Finite element analysis of three patterns of internal fixation of fractures of the mandibular condyle.

PubMed

Aquilina, Peter; Chamoli, Uphar; Parr, William C H; Clausen, Philip D; Wroe, Stephen

2013-06-01

The most stable pattern of internal fixation for fractures of the mandibular condyle is a matter for ongoing discussion. In this study we investigated the stability of three commonly used patterns of plate fixation, and constructed finite element models of a simulated mandibular condylar fracture. The completed models were heterogeneous in the distribution of bony material properties, contained about 1.2 million elements, and incorporated simulated jaw-adducting musculature. Models were run assuming linear elasticity and isotropic material properties for bone. This model was considerably larger and more complex than previous finite element models that have been used to analyse the biomechanical behaviour of differing plating techniques. The use of two parallel 2.0 titanium miniplates gave a more stable configuration with lower mean element stresses and displacements over the use of a single miniplate. In addition, a parallel orientation of two miniplates resulted in lower stresses and displacements than did the use of two miniplates in an offset pattern. The use of two parallel titanium plates resulted in a superior biomechanical result as defined by mean element stresses and relative movement between the fractured fragments in these finite element models. Copyright © 2012 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Tooth movements in foxhounds after one or two alveolar corticotomies.

PubMed

Sanjideh, Payam A; Rossouw, P Emile; Campbell, Phillip M; Opperman, Lynne A; Buschang, Peter H

2010-02-01

The aim of this split-mouth experimental study was to determine (1) whether corticotomy procedures increase tooth movement and (2) the effects of a second corticotomy procedure after 4 weeks on the rate of tooth movement. The mandibular third and maxillary second premolars of five skeletally mature male foxhounds, approximately 2 years of age, were extracted. One randomly selected mandibular quadrant had buccal and lingual flaps and corticotomies performed around the second premolar; the other quadrant served as the control. Both maxillary quadrants had initial buccal flaps and corticotomies; one randomly selected quadrant had a second buccal flap surgery and corticotomy after 28 days. Coil springs (200 g force), along with a 0.045 mm diameter tube on a 0.040 mm diameter guiding wire, were used to move the mandibular second and maxillary third premolars. Records, including digital calliper measurements and radiographs, were taken on days 0, 10, 14, 28, 42, and 56. Multilevel statistical procedures were used to model longitudinal tooth movements. The radiographic measurements initially showed increasing mandibular tooth movement rates, peaking between 22 and 25 days, and then decelerating. Total mandibular tooth movements were significantly (P < 0.05) greater on the experimental (2.4 mm) than on the control (1.3 mm) side. The rates of maxillary tooth movement slowed over time, with significantly (P < 0.05) more overall tooth movement on the side that had two (2.3 mm) than one (2.0 mm) corticotomy procedure. Alveolar corticotomy significantly increases orthodontic tooth movement. Performing a second corticotomy procedure after 4 weeks maintained higher rates of tooth movement over a longer duration and produced greater overall tooth movement than performing just one initial corticotomy, but the difference was small.

Functional anatomy of the temporo-mandibular joint (II).

PubMed

Sava, Anca; Scutariu, Monica

2012-01-01

Jaw movement is analyzed as an action between two rigid components jointed together in a particular way, the movable mandible against the stabilized cranium. Opening and closing movements are symmetrical; that is, both sides of the cranio-mandibular articulation are making the same movements. Protrusive and retrusive movements may also be symmetrical. The mandibular muscles determine all the complicated postures and-movements of the jaw. Their behavior can be greatly clarified by restating certain fundamentals crucial to purposive muscular activity. The joint derives its arterial supply from the superficial temporal artery and the maxillary artery. Branches of the auriculo-temporal and masseteric nerves and postganglionic sympathetic nerves supply the tissues associated with the capsular ligament and the looser posterior bilaminar extension of the disc.

Diagnostic abilities of three-dimensional electronic axiography on the basis of ARCUSdigma device.

PubMed

Bakalczuk, Magdalena; Bozyk, Andrzej; Iwanek, Michał; Borowicz, Janusz; Sykut, Janusz; Kleinrok, Janusz

2004-01-01

The ARCUSdigma is an electronic facebow enabling presentation and graphic analysis of mandibular movements on the computer screen. A kinematic hinge axis of the mandible can be determined using this device. The paper presents the diagnostic potential of the ARCUSdigma in relation to programming an articulator according to individual parameters of mandibular movements of the patient and its application in the diagnosis of temporo-mandibular joints.

Reduced mandibular range of motion in Duchenne Muscular Dystrophy: predictive factors.

PubMed

van Bruggen, H W; Van Den Engel-Hoek, L; Steenks, M H; Bronkhorst, E M; Creugers, N H J; de Groot, I J M; Kalaykova, S I

2015-06-01

Patients with Duchenne muscular dystrophy (DMD) experience negative effects upon feeding and oral health. We aimed to determine whether the mandibular range of motion in DMD is impaired and to explore predictive factors for the active maximum mouth opening (aMMO). 23 patients with DMD (mean age 16.7 ± 7.7 years) and 23 controls were assessed using a questionnaire about mandibular function and impairments. All participants underwent a clinical examination of the masticatory system, including measurement of mandibular range of motion and variables related to mandibular movements. In all patients, quantitative ultrasound of the digastric muscle and the geniohyoid muscle and the motor function measure (MFM) scale were performed. The patients were divided into early and late ambulatory stage (AS), early non-ambulatory stage (ENAS) and late non-ambulatory stage (LNAS). All mandibular movements were reduced in the patient group (P < 0.001) compared to the controls. Reduction in the aMMO (<40 mm) was found in 26% of the total patient group. LNAS patients had significantly smaller mandibular movements compared to AS and ENAS (P < 0.05). Multiple linear regression analysis for aMMO revealed a positive correlation with the body height and disease progression, with MFM total score as the strongest independent risk factor (R(2) = 0.71). Mandibular movements in DMD are significantly reduced and become more hampered with loss of motor function, including the sitting position, arm function, and neck and head control. We suggest that measurement of the aMMO becomes a part of routine care of patients with DMD. © 2015 John Wiley & Sons Ltd.

A Method of Three-Dimensional Recording of Mandibular Movement Based on Two-Dimensional Image Feature Extraction

PubMed Central

Li, Zhongke; Yang, Huifang; Lü, Peijun; Wang, Yong; Sun, Yuchun

2015-01-01

Background and Objective To develop a real-time recording system based on computer binocular vision and two-dimensional image feature extraction to accurately record mandibular movement in three dimensions. Methods A computer-based binocular vision device with two digital cameras was used in conjunction with a fixed head retention bracket to track occlusal movement. Software was developed for extracting target spatial coordinates in real time based on two-dimensional image feature recognition. A plaster model of a subject’s upper and lower dentition were made using conventional methods. A mandibular occlusal splint was made on the plaster model, and then the occlusal surface was removed. Temporal denture base resin was used to make a 3-cm handle extending outside the mouth connecting the anterior labial surface of the occlusal splint with a detection target with intersecting lines designed for spatial coordinate extraction. The subject's head was firmly fixed in place, and the occlusal splint was fully seated on the mandibular dentition. The subject was then asked to make various mouth movements while the mandibular movement target locus point set was recorded. Comparisons between the coordinate values and the actual values of the 30 intersections on the detection target were then analyzed using paired t-tests. Results The three-dimensional trajectory curve shapes of the mandibular movements were consistent with the respective subject movements. Mean XYZ coordinate values and paired t-test results were as follows: X axis: -0.0037 ± 0.02953, P = 0.502; Y axis: 0.0037 ± 0.05242, P = 0.704; and Z axis: 0.0007 ± 0.06040, P = 0.952. The t-test result showed that the coordinate values of the 30 cross points were considered statistically no significant. (P<0.05) Conclusions Use of a real-time recording system of three-dimensional mandibular movement based on computer binocular vision and two-dimensional image feature recognition technology produced a recording accuracy of approximately ± 0.1 mm, and is therefore suitable for clinical application. Certainly, further research is necessary to confirm the clinical applications of the method. PMID:26375800

Restricted Mandibular Movement Attributed to Ossification of Mandibular Depressors and Medial Pterygoid Muscles in Patients With Fibrodysplasia Ossificans Progressiva: A Report of 3 Cases.

PubMed

Okuno, Tetsuko; Suzuki, Hitoshi; Inoue, Akio; Kusukawa, Jingo

2017-09-01

Fibrodysplasia ossificans progressiva (FOP) is an extremely rare genetic condition characterized by congenital malformation and progressive heterotopic ossification (HO) caused by a recurrent single nucleotide substitution at position 617 in the ACVR1 gene. As the condition progresses, HO leads to joint ankylosis, breathing difficulties, and mouth-opening restriction, and it can shorten the patient's lifespan. This report describes 3 cases of FOP confirmed by genetic testing in patients with restricted mouth opening. Each patient presented a different onset and degree of jaw movement restriction. The anatomic ossification site of the mandibular joint was examined in each patient using reconstructed computed tomographic (CT) images and 3-dimensional reconstructed CT (3D-CT) images. A 29-year-old woman complained of jaw movement restriction since 13 years of age. 3D-CT image of the mandibular joint showed an osseous bridge, formed by the mandibular depressors that open the mouth, between the hyoid bone and the mentum of the mandible. A 39-year-old man presented with jaw movement restriction that developed at 3 years of age after a mouth injury. 3D-CT image of the jaw showed ankylosis of the jaw from ossification of the mandibular depressors that was worse than in patient 1. CT images showed no HO findings of the masticatory muscles. To the authors' knowledge, these are the first 2 case descriptions of the anatomic site of ankylosis involving HO of the mandibular depressors in the jaw resulting from FOP. In contrast, a 62-year-old bedridden woman with an interincisal distance longer than 10 mm (onset, 39 years of age) had no HO of the mandibular depressors and slight HO of the medial pterygoid muscle on the right and left sides. These findings suggest that restricted mouth opening varies according to the presence or absence of HO of the mandibular depressors. Copyright © 2017. Published by Elsevier Inc.

Protraction of mandibular second and third molars assisted by partial corticision and miniscrew anchorage.

PubMed

Mimura, Hiroshi

2013-08-01

A woman, aged 47 years 6 months, with an anterior open bite and a left-shifted mandible was treated with a mandibular right first molar extraction and without orthognathic surgery. However, her mandibular second molar did not move mesially during treatment because of the dense lamina dura; therefore, corticision was applied only on the mesial aspect of the mandibular second molar, and a miniscrew was inserted simultaneously. Corticision was introduced as a supplemental dentoalveolar surgery in orthodontic therapy to achieve accelerated tooth movement with minimal surgical intervention. In this technique, a reinforced scalpel was used as a thin chisel to separate the interproximal cortices transmucosally without a flap. This technique was applied not to accelerate tooth movement, but to protract the mandibular molars. One miniscrew was inserted on the mesiobuccal side of the mandibular right molar for protraction and intrusion. In addition, 2 miniscrews were inserted in the buccal sides of the maxillary first and second molars and the palatal side of the maxillary first molar to intrude them for correction of the mandibular shift and the cant of the occlusal plane. Excellent occlusion and correction of the anterior open bite were achieved without surgery. At the 2-year follow-up examination, the patient had a good occlusion and showed good stability with no opening of the extraction space. A partial corticision is an effective option for facilitating movement of mandibular molars. Copyright © 2013 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Electromyography of the buccal musculature of octopus (Octopus bimaculoides): a test of the function of the muscle articulation in support and movement.

PubMed

Uyeno, Theodore A; Kier, William M

2007-01-01

The buccal mass musculature of the octopus (Octopus bimaculoides) was studied with electromyography to test the predictions of a previous morphological study in which we suggested that the muscles of the buccal mass serve as both the effectors of movement and as the joint itself, forming a new category of flexible joint termed a ;muscle articulation'. The predictions of muscle function were tested by correlating muscle electrical activity in isolated buccal masses with spontaneous beak movements. Bipolar electromyography electrodes were implanted in the various beak muscles and beak position was recorded simultaneously with an electronic movement monitor (N=14). The results are consistent with the hypothesis that the lateral mandibular muscles produce opening movements of the beaks and provide the first definitive explanation of the opening mechanism. The results are also consistent with the hypothesis that the superior mandibular muscle functions primarily in closing. Co-contraction of the lateral mandibular muscles and the superior mandibular muscles was also observed, suggesting that these muscles may also stabilize the beaks during movement or provide a means of controlling the location of the pivot between the beaks. This study provides an important first test of the predictions of the role of the complex musculature found in muscle articulations such as the cephalopod buccal mass.

Afferent and Efferent Aspects of Mandibular Sensorimotor Control in Adults who Stutter

PubMed Central

Daliri, Ayoub; Prokopenko, Roman A.; Max, Ludo

2013-01-01

Purpose Individuals who stutter show sensorimotor deficiencies in speech and nonspeech movements. For the mandibular system, we dissociated the sense of kinesthesia from the efferent control component to examine whether kinesthetic integrity itself is compromised in stuttering or whether deficiencies occur only when generating motor commands. Method We investigated 11 stuttering and 11 nonstuttering adults’ kinesthetic sensitivity threshold and kinesthetic accuracy for passive jaw movements as well as their minimal displacement threshold and positioning accuracy for active jaw movements. We also investigated the correlation with an anatomical index of jaw size. Results The groups showed no statistically significant differences on sensory measures for passive jaw movements. Although some stuttering individuals performed more poorly than any nonstuttering participants on the active movement tasks, between-group differences for active movements were also not statistically significant. Unlike fluent speakers, however, the stuttering group showed a statistically significant correlation between mandibular size and performance in the active and passive near-threshold tasks. Conclusions Previously reported minimal movement differences were not replicated. Instead, stuttering individuals’ performance varied with anatomical properties. These correlational results are consistent with the hypothesis that stuttering participants generate and perceive movements based on less accurate internal models of the involved neuromechanical systems. PMID:23816664

Deranged jaw-neck motor control in whiplash-associated disorders.

PubMed

Eriksson, Per-Olof; Zafar, Hamayun; Häggman-Henrikson, Birgitta

2004-02-01

Recent findings of simultaneous and well coordinated head-neck movements during single as well as rhythmic jaw opening-closing tasks has led to the conclusion that 'functional jaw movements' are the result of activation of jaw as well as neck muscles, leading to simultaneous movements in the temporomandibular, atlanto-occipital and cervical spine joints. It can therefore be assumed that disease or injury to any of these joint systems would disturb natural jaw function. To test this hypothesis, amplitudes, temporal coordination, and spatiotemporal consistency of concomitant mandibular and head-neck movements during single maximal jaw opening-closing tasks were analysed in 25 individuals suffering from whiplash-associated disorders (WAD) using optoelectronic movement recording technique. In addition, the relative durations for which the head position was equal to, leading ahead of, or lagging behind the mandibular position during the entire jaw opening-closing cycle were determined. Compared with healthy individuals, the WAD group showed smaller amplitudes, and changed temporal coordination between mandibular and head-neck movements. No divergence from healthy individuals was found for the spatiotemporal consistency or for the analysis during the entire jaw opening-closing cycle. These findings in the WAD group of a 'faulty', but yet consistent, jaw-neck behavior may reflect a basic importance of linked control of the jaw and neck sensory-motor systems. In conclusion, the present results suggest that neck injury is associated with deranged control of mandibular and head-neck movements during jaw opening-closing tasks, and therefore might compromise natural jaw function.

Individual tooth macrowear pattern guides the reconstruction of Sts 52 (Australopithecus africanus) dental arches.

PubMed

Benazzi, Stefano; Kullmer, Ottmar; Schulz, Dieter; Gruppioni, Giorgio; Weber, Gerhard W

2013-02-01

The functional restoration of the occlusal relationship between maxillary and mandibular tooth rows is a major challenge in modern dentistry and maxillofacial surgery. Similar technical challenges are present in paleoanthropology when considering fragmented and deformed mandibular and maxillary fossils. Sts 52, an Australopithecus africanus specimen from Sterkfontein Member 4, represents a typical case where the original shape of the dental arches is no longer preserved. It includes a partial lower face (Sts 52a) and a fragmented mandible (Sts 52b), both incomplete and damaged to such an extent to thwart attempts at matching upper and lower dentitions. We show how the preserved macro wear pattern of the tooth crowns can be used to functionally reconstruct Sts 52's dental arches. High-resolution dental stone casts of Sts 52 maxillary and mandibular dentition were mounted and repositioned in a dental articulator. The occlusal relationship between antagonists was restored based on the analysis of the occlusal wear pattern of each preserved tooth, considering all dental contact movements represented in the occlusal compass. The reconstructed dental arches were three-dimensional surface scanned and their occlusal kinematics tested in a simulation. The outcome of this contribution is the first functional restoration of A. africanus dental arches providing new morphometric data for specimen Sts 52. It is noteworthy that the method described in this case study might be applied to several other fossil specimens. Copyright © 2013 Wiley Periodicals, Inc.

Accuracy of a Real-Time, Computerized, Binocular, Three-Dimensional Trajectory-Tracking Device for Recording Functional Mandibular Movements

PubMed Central

Zhao, Tian; Yang, Huifang; Sui, Huaxin; Salvi, Satyajeet Sudhir; Wang, Yong; Sun, Yuchun

2016-01-01

Objective Developments in digital technology have permitted researchers to study mandibular movements. Here, the accuracy of a real-time, computerized, binocular, three-dimensional (3D) trajectory-tracking device for recording functional mandibular movements was evaluated. Methods An occlusal splint without the occlusal region was created based on a plaster cast of the lower dentition. The splint was rigidly connected with a target on its labial side and seated on the cast. The cast was then rigidly attached to the stage of a high-precision triaxial electronic translator, which was used to move the target-cast-stage complex. Half-circular movements (5.00-mm radius) in three planes (XOY, XOZ, YOZ) and linear movements along the x-axis were performed at 5.00 mm/s. All trajectory points were recorded with the binocular 3D trajectory-tracking device and fitted to arcs or lines, respectively, with the Imageware software. To analyze the accuracy of the trajectory-tracking device, the mean distances between the trajectory points and the fitted arcs or lines were measured, and the mean differences between the lengths of the fitted arcs’ radii and a set value (5.00 mm) were then calculated. A one-way analysis of variance was used to evaluate the spatial consistency of the recording accuracy in three different planes. Results The mean distances between the trajectory points and fitted arcs or lines were 0.076 ± 0.033 mm or 0.089 ± 0.014 mm. The mean difference between the lengths of the fitted arcs’ radii and the set value (5.00 mm) was 0.025 ± 0.071 mm. A one-way ANOVA showed that the recording errors in three different planes were not statistically significant. Conclusion These results suggest that the device can record certain movements at 5.00 mm/s, which is similar to the speed of functional mandibular movements. In addition, the recordings had an error of <0.1 mm and good spatial consistency. Thus, the device meets some of the requirements necessary for recording human mandibular movements. PMID:27701462

Condylar motion in children with primary dentition during lateral excursion.

PubMed

Yamasaki, Youichi; Hayasaki, Haruaki; Nishi, Megumi; Nakata, Shiho; Nakata, Minoru

2002-07-01

Normal development of primary and mixed dentition is indispensable for establishing a healthy mandibular function of the permanent dentition. Because condylar movements are crucial for mandibular function, extensive studies have been reported. However, most of these studies have dealt with mandibular functions in adults, and there is less known about children with primary dentition. The purpose of this study was to clarify the condylar movements during lateral excursions in children with primary dentition and compare these movements with those of adults from the viewpoint of functional development. With use of an optoelectronic recording system with six degrees of freedom, the lateral excursions of 24 children and 20 young women, with sound dentition, were recorded at 100 Hz. The results show that the balancing side condyle of the children had a significantly smaller vertical excursion and a significantly larger anteroposterior excursion than that of adults, indicating the shallower and more anteriorly directed movements of the entire mandible during lateral excursions in children with primary dentition.

[Temporo-mandibular joint. Morpho-functional considerations].

PubMed

Scutariu, M D; Indrei, Anca

2004-01-01

The temporo-mandibular joint is distinguished from most other synovial joints of the body by two features: 1. the two jointed components carry teeth whose position and occlusion introduce a very strong influence on the movements of the temporo-mandibular joint and 2. its articular surfaces are not covered by hyaline cartilage, but by a dense, fibrous tissue. This paper describes the parts of the temporo-mandibular joint: the articular surfaces (the condylar process of the mandible and the glenoid part of the temporal bone), the fibrocartilaginous disc which is interposed between the mandibular and the temporal surface, the fibrous capsule of the temporo-mandibular joint and the ligaments of this joint. All these parts present a very strong adaptation at the important functions of the temporo-mandibular joint.

The fabrication of a customized occlusal splint based on the merging of dynamic jaw tracking records, cone beam computed tomography, and CAD-CAM digital impression.

PubMed

Aslanidou, Katerina; Kau, Chung How; Vlachos, Christos; Saleh, Tayem Abou

2017-01-01

The aim of this case report was to present the procedure of fabricating a customized occlusal splint, through a revolutionary software that combines cone beam computed tomography (CBCT) with jaw motion tracking (JMT) data and superimposes a digital impression. The case report was conducted on a 46-year-old female patient diagnosed with the temporomandibular disorder. A CBCT scan and an optical impression were obtained. The range of the patient's mandibular movements was captured with a JMT device. The data were combined in the SICAT software (SICAT, Sirona, Bonn, Germany). The software enabled the visualization of patient-specific mandibular movements and provided a real dynamic anatomical evaluation of the condylar position in the glenoid fossa. After the assessment of the range of movements during opening, protrusion, and lateral movements all the data were sent to SICAT and a customized occlusal splint was manufactured. The SICAT software provides a three-dimensional real-dynamic simulation of mandibular movements relative to the patient-specific anatomy of the jaw; thus, it opens new possibilities and potentials for the management of temporomandibular disorders.

Kinematics of the human mandible for different head postures.

PubMed

Visscher, C M; Huddleston Slater, J J; Lobbezoo, F; Naeije, M

2000-04-01

The influence of head posture on movement paths of the incisal point (IP) and of the mandibular condyles during free open-close movements was studied. Ten persons, without craniomandibular or cervical spine disorders, participated in the study. Open close mandibular movements were recorded with the head in five postures, viz., natural head posture, forward head posture, military posture, and lateroflexion to the right and to the left side, using the Oral Kinesiologic Analysis System (OKAS-3D). This study showed that in a military head posture, the opening movement path of the incisal point is shifted anteriorly relative to the path in a natural head posture. In a forward head posture, the movement path is shifted posteriorly whereas during lateroflexion, it deviates to the side the head has moved to. Moreover, the intra-articular distance in the temporomandibular joint during closing is smaller with the head in military posture and greater in forward head posture, as compared to the natural head posture. During lateroflexion, the intra-articular distance on the ipsilateral side is smaller. The influence of head posture upon the kinematics of the mandible is probably a manifestation of differences in mandibular loading in the different head postures.

Alloplastic total temporomandibular joint replacements: do they perform like natural joints? Prospective cohort study with a historical control.

PubMed

Wojczyńska, A; Leiggener, C S; Bredell, M; Ettlin, D A; Erni, S; Gallo, L M; Colombo, V

2016-10-01

The aim of this study was to qualitatively and quantitatively describe the biomechanics of existing total alloplastic reconstructions of temporomandibular joints (TMJ). Fifteen patients with unilateral or bilateral TMJ total joint replacements and 15 healthy controls were evaluated via dynamic stereometry technology. This non-invasive method combines three-dimensional imaging of the subject's anatomy with jaw tracking. It provides an insight into the patient's jaw joint movements in real time and provides a quantitative evaluation. The patients were also evaluated clinically for jaw opening, protrusive and laterotrusive movements, pain, interference with eating, and satisfaction with the joint replacements. The qualitative assessment revealed that condyles of bilateral total joint replacements displayed similar basic motion patterns to those of unilateral prostheses. Quantitatively, mandibular movements of artificial joints during opening, protrusion, and laterotrusion were all significantly shorter than those of controls. A significantly restricted mandibular range of motion in replaced joints was also observed clinically. Fifty-three percent of patients suffered from chronic pain at rest and 67% reported reduced chewing function. Nonetheless, patients declared a high level of satisfaction with the replacement. This study shows that in order to gain a comprehensive understanding of complex therapeutic measures, a multidisciplinary approach is needed. Copyright © 2016 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Adapted cuing technique: facilitating sequential phoneme production.

PubMed

Klick, S L

1994-09-01

ACT is a visual cuing technique designed to facilitate dyspraxic speech by highlighting the sequential production of phonemes. In using ACT, cues are presented in such a way as to suggest sequential, coarticulatory movement in an overall pattern of motion. While using ACT, the facilitator's hand moves forward and back along the side of her (or his) own face. Finger movements signal specific speech sounds in formations loosely based on the manual alphabet for the hearing impaired. The best movements suggest the flowing, interactive nature of coarticulated phonemes. The synergistic nature of speech is suggested by coordinated hand motions which tighten and relax, move quickly or slowly, reflecting the motions of the vocal tract at various points during production of phonemic sequences. General principles involved in using ACT include a primary focus on speech-in-motion, the monitoring and fading of cues, and the presentation of stimuli based on motor-task analysis of phonemic sequences. Phonemic sequences are cued along three dimensions: place, manner, and vowel-related mandibular motion. Cuing vowels is a central feature of ACT. Two parameters of vowel production, focal point of resonance and mandibular closure, are cued. The facilitator's hand motions reflect the changing shape of the vocal tract and the trajectory of the tongue that result from the coarticulation of vowels and consonants. Rigid presentation of the phonemes is secondary to the facilitator's primary focus on presenting the overall sequential movement. The facilitator's goal is to self-tailor ACT in response to the changing needs and abilities of the client.(ABSTRACT TRUNCATED AT 250 WORDS)

Positional relationships between the masticatory muscles and their innervating nerves with special reference to the lateral pterygoid and the midmedial and discotemporal muscle bundles of temporalis

PubMed Central

AKITA, KEIICHI; SHIMOKAWA, TAKASHI; SATO, TATSUO

2000-01-01

For an accurate assessment of jaw movement, it is crucial to understand the comprehensive formation of the masticatory muscles with special reference to the relationship to the disc of the temporomandibular joint. Detailed dissection was performed on 26 head halves of 14 Japanese cadavers in order to obtain precise anatomical information of the positional relationships between the masticatory muscles and the branches of the mandibular nerve. After complete removal of the bony elements, the midmedial muscle bundle in all specimens and the discotemporal muscle bundle in 6 specimens, derivatives of the temporalis, which insert into the disc were observed. On the anterior area of the articular capsule and the disc of the temporomandibular joint, the upper head of the lateral pterygoid, the midmedial muscle bundle of temporalis and the discotemporal bundle of temporalis were attached mediolaterally, and in 3 specimens the posterosuperior margin of the zygomaticomandibularis was attached to the anterolateral area of the disc. It is suggested that these muscles and muscle bundles contribute to various mandibular movements. Although various patterns of the positional relationships between the muscles and muscle bundles and the their innervating nerves are observed in the present study, relative positional relationships of the muscles and muscle bundles and of nerves of the mandibular nerve are consistent. A possible scheme of the developmental formation of the masticatory muscles based on the findings of the positional relationships between the muscles and the nerves is presented. PMID:11005720

Orthodontic decompensation in skeletal Class III malocclusion: redefining the amount of movement assessed by Cone-Beam Computed Tomography

PubMed Central

Cappellozza, José Antonio Zuega; Guedes, Fabio Pinto; Nary, Hugo; Capelozza, Leopoldino; Cardoso, Mauricio de Almeida

2015-01-01

Introduction: Cone-Beam Computed Tomography (CBCT) is essential for tridimensional planning of orthognathic surgery, as it allows visualization and evaluation of bone structures and mineralized tissues. Tomographic slices allow evaluation of tooth inclination and individualization of movement performed during preoperative decompensation. The aim of this paper was to assess maxillary and mandibular incisors inclination pre and post orthodontic decompensation in skeletal Class III malocclusion. Methods: The study was conducted on six individuals with skeletal Class III malocclusion, surgically treated, who had Cone-Beam Computed Tomographic scans obtained before and after orthodontic decompensation. On multiplanar reconstruction view, tomographic slices (axial, coronal and sagittal) were obtained on the long axis of each incisor. The sagittal slice was used for measurement taking, whereas the references used to assess tooth inclination were the long axis of maxillary teeth in relation to the palatal plane and the long axis of mandibular teeth in relation to the mandibular plane. Results: There was significant variation in the inclination of incisors before and after orthodontic decompensation. This change was of greater magnitude in the mandibular arch, evidencing that natural compensation is more effective in this arch, thereby requiring more intensive decompensation. Conclusion: When routinely performed, the protocols of decompensation treatment in surgical individuals often result in intensive movements, which should be reevaluated, since the extent of movement predisposes to reduction in bone attachment levels and root length. PMID:26560818

Accurate 3D kinematic measurement of temporomandibular joint using X-ray fluoroscopic images

NASA Astrophysics Data System (ADS)

Yamazaki, Takaharu; Matsumoto, Akiko; Sugamoto, Kazuomi; Matsumoto, Ken; Kakimoto, Naoya; Yura, Yoshiaki

2014-04-01

Accurate measurement and analysis of 3D kinematics of temporomandibular joint (TMJ) is very important for assisting clinical diagnosis and treatment of prosthodontics and orthodontics, and oral surgery. This study presents a new 3D kinematic measurement technique of the TMJ using X-ray fluoroscopic images, which can easily obtain the TMJ kinematic data in natural motion. In vivo kinematics of the TMJ (maxilla and mandibular bone) is determined using a feature-based 2D/3D registration, which uses beads silhouette on fluoroscopic images and 3D surface bone models with beads. The 3D surface models of maxilla and mandibular bone with beads were created from CT scans data of the subject using the mouthpiece with the seven strategically placed beads. In order to validate the accuracy of pose estimation for the maxilla and mandibular bone, computer simulation test was performed using five patterns of synthetic tantalum beads silhouette images. In the clinical applications, dynamic movement during jaw opening and closing was conducted, and the relative pose of the mandibular bone with respect to the maxilla bone was determined. The results of computer simulation test showed that the root mean square errors were sufficiently smaller than 1.0 mm and 1.0 degree. In the results of clinical application, during jaw opening from 0.0 to 36.8 degree of rotation, mandibular condyle exhibited 19.8 mm of anterior sliding relative to maxillary articular fossa, and these measurement values were clinically similar to the previous reports. Consequently, present technique was thought to be suitable for the 3D TMJ kinematic analysis.

Biology of biomechanics: Finite element analysis of a statically determinate system to rotate the occlusal plane for correction of a skeletal Class III open-bite malocclusion.

PubMed

Roberts, W Eugene; Viecilli, Rodrigo F; Chang, Chris; Katona, Thomas R; Paydar, Nasser H

2015-12-01

In the absence of adequate animal or in-vitro models, the biomechanics of human malocclusion must be studied indirectly. Finite element analysis (FEA) is emerging as a clinical technology to assist in diagnosis, treatment planning, and retrospective analysis. The hypothesis tested is that instantaneous FEA can retrospectively simulate long-term mandibular arch retraction and occlusal plane rotation for the correction of a skeletal Class III malocclusion. Seventeen published case reports were selected of patients treated with statically determinate mechanics using posterior mandible or infrazygomatic crest bone screw anchorage to retract the mandibular arch. Two-dimensional measurements were made for incisor and molar movements, mandibular arch rotation, and retraction relative to the maxillary arch. A patient with cone-beam computed tomography imaging was selected for a retrospective FEA. The mean age for the sample was 23.3 ± 3.3 years; there were 7 men and 10 women. Mean incisor movements were 3.35 ± 1.55 mm of retraction and 2.18 ± 2.51 mm of extrusion. Corresponding molar movements were retractions of 4.85 ± 1.78 mm and intrusions of 0.85 ± 2.22 mm. Retraction of the mandibular arch relative to the maxillary arch was 4.88 ± 1.41 mm. Mean posterior rotation of the mandibular arch was -5.76° ± 4.77° (counterclockwise). The mean treatment time (n = 16) was 36.2 ± 15.3 months. Bone screws in the posterior mandibular region were more efficient for intruding molars and decreasing the vertical dimension of the occlusion to close an open bite. The full-cusp, skeletal Class III patient selected for FEA was treated to an American Board of Orthodontics Cast-Radiograph Evaluation score of 24 points in about 36 months by en-masse retraction and posterior rotation of the mandibular arch: the bilateral load on the mandibular segment was about 200 cN. The mandibular arch was retracted by about 5 mm, posterior rotation was about 16.5°, and molar intrusion was about 3 mm. There was a 4° decrease in the mandibular plane angle to close the skeletal open bite. Retrospective sequential iterations (FEA animation) simulated the clinical response, as documented with longitudinal cephalometrics. The level of periodontal ligament stress was relatively uniform (<5 kPa) for all teeth in the mandibular arch segment. En-masse retraction of the mandibular arch is efficient for conservatively treating a skeletal Class III malocclusion. Posterior mandibular anchorage causes intrusion of the molars to close the vertical dimension of the occlusion and the mandibular plane angle. Instantaneous FEA as modeled here could be used to reasonably predict the clinical results of an applied load. Copyright © 2015 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Realization of masticatory movement by 3-dimensional simulation of the temporomandibular joint and the masticatory muscles.

PubMed

Park, Jong-Tae; Lee, Jae-Gi; Won, Sung-Yoon; Lee, Sang-Hee; Cha, Jung-Yul; Kim, Hee-Jin

2013-07-01

Masticatory muscles are closely involved in mastication, pronunciation, and swallowing, and it is therefore important to study the specific functions and dynamics of the mandibular and masticatory muscles. However, the shortness of muscle fibers and the diversity of movement directions make it difficult to study and simplify the dynamics of mastication. The purpose of this study was to use 3-dimensional (3D) simulation to observe the functions and movements of each of the masticatory muscles and the mandible while chewing. To simulate the masticatory movement, computed tomographic images were taken from a single Korean volunteer (30-year-old man), and skull image data were reconstructed in 3D (Mimics; Materialise, Leuven, Belgium). The 3D-reconstructed masticatory muscles were then attached to the 3D skull model. The masticatory movements were animated using Maya (Autodesk, San Rafael, CA) based on the mandibular motion path. During unilateral chewing, the mandible was found to move laterally toward the functional side by contracting the contralateral lateral pterygoid and ipsilateral temporalis muscles. During the initial mouth opening, only hinge movement was observed at the temporomandibular joint. During this period, the entire mandible rotated approximately 13 degrees toward the bicondylar horizontal plane. Continued movement of the mandible to full mouth opening occurred simultaneously with sliding and hinge movements, and the mandible rotated approximately 17 degrees toward the center of the mandibular ramus. The described approach can yield data for use in face animation and other simulation systems and for elucidating the functional components related to contraction and relaxation of muscles during mastication.

Sliding mechanics with microscrew implant anchorage.

PubMed

Park, Hyo-Sang; Kwon, Tae-Geon

2004-10-01

Three cases are illustrated. One was treated with maxillary microscrew implants, another with mandibular microscrew implants, and the third with both maxillary and mandibular microscrew implants. With the maxillary microscrew implants, the maxillary anterior teeth were retracted bodily with a slight intrusion and all the premolar extraction space was closed without loss of anchorage. Furthermore, the maxillary posterior teeth showed distal movement. The mandibular microscrew implants controlled the vertical position of the mandibular posterior teeth and played an important role in improving the facial profile. The efficacy of sliding mechanics with microscrew implant anchorage on the treatment of skeletal Class II malocclusion is also discussed.

Evolution of Muscle Activity Patterns Driving Motions of the Jaw and Hyoid during Chewing in Gnathostomes

PubMed Central

Konow, Nicolai; Herrel, Anthony; Ross, Callum F.; Williams, Susan H.; German, Rebecca Z.; Sanford, Christopher P. J.; Gintof, Chris

2011-01-01

Although chewing has been suggested to be a basal gnathostome trait retained in most major vertebrate lineages, it has not been studied broadly and comparatively across vertebrates. To redress this imbalance, we recorded EMG from muscles powering anteroposterior movement of the hyoid, and dorsoventral movement of the mandibular jaw during chewing. We compared muscle activity patterns (MAP) during chewing in jawed vertebrate taxa belonging to unrelated groups of basal bony fishes and artiodactyl mammals. Our aim was to outline the evolution of coordination in MAP. Comparisons of activity in muscles of the jaw and hyoid that power chewing in closely related artiodactyls using cross-correlation analyses identified reorganizations of jaw and hyoid MAP between herbivores and omnivores. EMG data from basal bony fishes revealed a tighter coordination of jaw and hyoid MAP during chewing than seen in artiodactyls. Across this broad phylogenetic range, there have been major structural reorganizations, including a reduction of the bony hyoid suspension, which is robust in fishes, to the acquisition in a mammalian ancestor of a muscle sling suspending the hyoid. These changes appear to be reflected in a shift in chewing MAP that occurred in an unidentified anamniote stem-lineage. This shift matches observations that, when compared with fishes, the pattern of hyoid motion in tetrapods is reversed and also time-shifted relative to the pattern of jaw movement. PMID:21705368

Afferent and Efferent Aspects of Mandibular Sensorimotor Control in Adults Who Stutter

ERIC Educational Resources Information Center

Daliri, Ayoub; Prokopenko, Roman A.; Max, Ludo

2013-01-01

Purpose: Individuals who stutter show sensorimotor deficiencies in speech and nonspeech movements. For the mandibular system, the authors dissociated the sense of kinesthesia from the efferent control component to examine whether kinesthetic integrity itself is compromised in stuttering or whether deficiencies occur only when generating motor…

Nonsurgical correction of a Class III malocclusion in an adult by miniscrew-assisted mandibular dentition distalization.

PubMed

Jing, Yan; Han, Xianglong; Guo, Yongwen; Li, Jingyu; Bai, Ding

2013-06-01

This article reports the successful use of miniscrews in the mandible to treat a 20-year-old Mongolian woman with a chief complaint of anterior crossbite. The patient had a skeletal Class III malocclusion with a mildly protrusive mandible, an anterior crossbite, and a deviated midline. In light of the advantages for reconstruction of the occlusal plane and distal en-masse movement of the mandibular arch, we used a multiloop edgewise archwire in the initial stage. However, the maxillary incisors were in excessive labioversion accompanied by little retraction of the mandibular incisors; these results were obviously not satisfying after 4 months of multiloop edgewise archwire treatment. Two miniscrews were subsequently implanted vertically in the external oblique ridge areas of the bilateral mandibular ramus as skeletal anchorage for en-masse distalization of the mandibular dentition. During treatment, the mandibular anterior teeth were retracted about 4.0 mm without negative lingual inclinations. The movement of the mandibular first molar was almost bodily translation. The maxillary incisors maintained good inclinations by rotating their brackets 180° along with the outstanding performance of the beta-titanium wire. The patient received a harmonious facial balance, an attractive smile, and ideal occlusal relationships. The outcome was stable after 1 year of retention. Our results suggest that the application of miniscrews in the posterior area of the mandible is an effective approach for Class III camouflage treatment. This technique requires minimal compliance and is particularly useful for correcting Class III patients with mild mandibular protrusion and minor crowding. Copyright © 2013 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Dive and beak movement patterns in leatherback turtles Dermochelys coriacea during internesting intervals in French Guiana.

PubMed

Fossette, Sabrina; Gaspar, Philippe; Handrich, Yves; Le Maho, Yvon; Georges, Jean-Yves

2008-03-01

1. Investigating the foraging patterns of free-ranging species is essential to estimate energy/time budgets for assessing their real reproductive strategy. Leatherback turtles Dermochelys coriacea (Vandelli 1761), commonly considered as capital breeders, have been reported recently to prospect actively during the breeding season in French Guiana, Atlantic Ocean. In this study we investigate the possibility of this active behaviour being associated with foraging, by studying concurrently diving and beak movement patterns in gravid females equipped with IMASEN (Inter-MAndibular Angle SENsor). 2. Four turtles provided data for periods varying from 7.3 to 56.1 h while exhibiting continuous short and shallow benthic dives. Beak movement ('b-m') events occurred in 34% of the dives, on average 1.8 +/- 1.4 times per dive. These b-m events lasted between 1.5 and 20 s and occurred as isolated or grouped (two to five consecutive beak movements) events in 96.0 +/- 4.0% of the recorded cases, and to a lesser extent in series (> five consecutive beak movements). 3. Most b-m events occurred during wiggles at the bottom of U- and W-shaped dives and at the beginning and end of the bottom phase of the dives. W-shaped dives were associated most frequently with beak movements (65% of such dives) and in particular with grouped beak movements. 4. Previous studies proposed wiggles to be indicator of predatory activity, U- and W-shaped dives being putative foraging dives. Beak movements recorded in leatherbacks during the first hours of their internesting interval in French Guiana may be related to feeding attempts. 5. In French Guiana, leatherbacks show different mouth-opening patterns for different dive patterns, suggesting that they forage opportunistically on occasional prey, with up to 17% of the dives appearing to be successful feeding dives. 6. This study highlights the contrasted strategies adopted by gravid leatherbacks nesting on the Pacific coasts of Costa Rica, in the deep-water Caribbean Sea and in the French Guianan shallow continental shelf, and may be related to different local prey accessibility among sites. Our results may help to explain recently reported site-specific individual body size and population dynamics.

[Comparison of self-controlled retruded approach and bimanual manipulation method on the relationship of incisal point displacement in the mandibular retruded contact position].

PubMed

Zhang, Lei; Li, Yun-xia; Kang, Yan-feng; Yang, Guang-ju; Xie, Qiu-fei

2014-02-18

To evaluate the relationship of incisal point displacements in the mandibular retruded contact position (RCP) between the self-controlled retruded approach and bimanual manipulation method. Twelve healthy young volunteers were selected. The RCP was guided through the self-controlled retruded approach and bimanual manipulation method. The track of the incisal point was recorded, using the mandibular movement trace recording system. The movement direction of the incisal point in horizontal plane was observed. The distance between the incisal point of the RCP and intercuspal contact position (ICP) was measured. Except one volunteer's incisal point movement direction of the RCP was oblique, others were straight toward posterior. The displacements of the incisal point from the ICP to RCP guided through self-controlled approach and bimanual manipulation method were (1.15 ± 0.64) mm, (0.98 ± 0.29) mm respectively. There was no statistical significance between the two methods (P > 0.05). The displacements of the incisal point from the ICP to RCP guided through self-controlled approach and bimanual manipulation method are approximately the same.

Are Biodegradable Plates Applicable in Endoscope-Assisted Open Reduction and Internal Fixation of Mandibular Subcondyle Fractures?

PubMed

Son, Jang-Ho; Ha, Jinhee; Cho, Yeong-Cheol; Sung, Iel-Yong

2017-08-01

To investigate whether biodegradable plates are applicable in endoscope-assisted open reduction and internal fixation (EAORIF) of mandibular subcondyle fractures. This retrospective case-series study included patients with mandibular subcondyle fractures treated with EAORIF using an unsintered hydroxyapatite particles/poly-l-lactide biodegradable plate system, with at least 6 months of clinical follow-up data available. The outcome variables were fracture healing with postoperative stability and postoperative complications. Other variables included age, gender, fracture site, cause of injury, accompanying mandibular fracture, total follow-up period, fracture classification, extent of displacement, preoperative status of occlusion, preoperative mandibular movements, fixation materials in accompanying mandibular fracture, location and number of fixation plates, periods of intermaxillary fixation/elastic bands, and postoperative mandibular movements. Fracture healing in these patients was assessed by comparing the immediate postoperative cone-beam computed tomography (CBCT) images with those obtained at least 3 months after surgery. A total of 11 patients, 9 male and 2 female, with a mean ± standard deviation age of 35.3 ± 15.9 years, were included. The mean follow-up period was 18.8 ± 7.8 months. Four patients had an accompanying mandibular fracture. Two 4-hole, 2.0-mm biodegradable plates were fixed with 6-mm screws along the posterior border of the mandibular ramus and near the sigmoid notch. Complete bone formation around the fracture lines or fading of the fracture lines, with no change in the position of the fractured segments, was observed on the postoperative CBCT images at 3 months. With the exception of 2 patients, no patient complained of plate palpability, deviation in occlusion, or discomfort during the postoperative follow-up period. EAORIF using biodegradable plates for mandible subcondylar fractures is a stable and reliable method, with considerable advantages compared with titanium plates. Copyright © 2017 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Measurements of jaw movements and TMJ pain intensity in patients treated with GaAlAs laser.

PubMed

Mazzetto, Marcelo Oliveira; Hotta, Takami Hirono; Pizzo, Renata Campi de Andrade

2010-01-01

The aim of this study was to evaluate the effectiveness of low-level laser therapy (LLLT) on the improvement of the mandibular movements and painful symptoms in individuals with temporomandibular disorders (TMD). Forty patients were randomly divided into two groups (n=20): Group 1 received the effective dose (GaAlAs laser λ 830 nm, 40 mW, 5J/cm²) and Group 2 received the placebo application (0 J/cm²), in continuous mode on the affected condyle lateral pole: superior, anterior, posterior, and posterior-inferior, twice a week during 4 weeks. Four evaluations were performed: E1 (before laser application), E2 (right after the last application), E3 (one week after the last application) and E4 (30 days after the last application). The Kruskal-Wallis test showed significant more improvements (p<0.01) in painful symptoms in the treated group than in the placebo group. A significant improvement in the range of mandibular movements was observed when the results were compared between the groups at E4. Laser application can be a supportive therapy in the treatment of TMD, since it resulted in the immediate decrease of painful symptoms and increased range of mandibular movements in the treated group. The same results were not observed in the placebo group.

Cranial and mandibular shape variation in the genus Carollia (Mammalia: Chiroptera) from Colombia: biogeographic patterns and morphological modularity.

PubMed

López-Aguirre, Camilo; Pérez-Torres, Jairo; Wilson, Laura A B

2015-01-01

Neotropical bats of the genus Carollia are widely studied due to their abundance, distribution and relevance for ecosystems. However, the ecomorphological boundaries of these species are poorly differentiated, and consequently correspondence between their geographic distribution, ecological plasticity and morphological variation remains unclear. In this study, patterns of cranial and mandibular morphological variation were assessed for Carollia brevicauda, C. castanea and C. perspicillata from Colombia. Using geometric morphometrics, morphological variation was examined with respect to: differences in intraspecific variation, morphological modularity and integration, and biogeographic patterns. Patterns of intraspecific variation were different for each species in both cranial and mandibular morphology, with functional differences apparent according to diet. Cranial modularity varied between species whereas mandibular modularity did not. High cranial and mandibular correlation reflects Cranium-Mandible integration as a functional unit. Similarity between the biogeographic patterns in C. brevicauda and C. perspicillata indicates that the Andes do not act as a barrier but rather as an independent region, isolating the morphology of Andean populations of larger-bodied species. The biogeographic pattern for C. castanea was not associated with the physiography of the Andes, suggesting that large body size does not benefit C. brevicauda and C. perspicillata in maintaining homogeneous morphologies among populations.

Cranial and mandibular shape variation in the genus Carollia (Mammalia: Chiroptera) from Colombia: biogeographic patterns and morphological modularity

PubMed Central

Pérez-Torres, Jairo; Wilson, Laura A. B.

2015-01-01

Neotropical bats of the genus Carollia are widely studied due to their abundance, distribution and relevance for ecosystems. However, the ecomorphological boundaries of these species are poorly differentiated, and consequently correspondence between their geographic distribution, ecological plasticity and morphological variation remains unclear. In this study, patterns of cranial and mandibular morphological variation were assessed for Carollia brevicauda, C. castanea and C. perspicillata from Colombia. Using geometric morphometrics, morphological variation was examined with respect to: differences in intraspecific variation, morphological modularity and integration, and biogeographic patterns. Patterns of intraspecific variation were different for each species in both cranial and mandibular morphology, with functional differences apparent according to diet. Cranial modularity varied between species whereas mandibular modularity did not. High cranial and mandibular correlation reflects Cranium-Mandible integration as a functional unit. Similarity between the biogeographic patterns in C. brevicauda and C. perspicillata indicates that the Andes do not act as a barrier but rather as an independent region, isolating the morphology of Andean populations of larger-bodied species. The biogeographic pattern for C. castanea was not associated with the physiography of the Andes, suggesting that large body size does not benefit C. brevicauda and C. perspicillata in maintaining homogeneous morphologies among populations. PMID:26413433

Rotational movements of mandibular two-implant overdentures.

PubMed

Kimoto, Suguru; Pan, Shaoxia; Drolet, Nicolas; Feine, Jocelyne S

2009-08-01

Clinicians have reported that their patients complain that their mandibular two-implant overdentures (IOD) rotate. Therefore, we studied the frequency and severity of rotation of IODs with two-ball attachments, how rotation may influence perceived satisfaction ratings of chewing ability, and the factors that are involved in the rotation of IODs. Seventy-nine participants were recruited and asked to rate their general satisfaction of their IODs, as well as their ability to chew foods, the existence of any mandibular denture rotation, and to what degree denture rotation bothered them. Data on participant sociodemographic, anatomical, and prosthesis characteristics were also collected. Student's t-test and logistic regression analyses were performed to analyze the differences between participants who did (R group) and did not report (NR group) denture rotation. Thirty-seven of 79 participants were aware of rotational movement in their IODs. These patients were significantly less satisfied with their chewing ability than those who felt no rotation (69.1 mm R group vs. 82.9 mm), and discomfort caused by the rotation bothered them moderately (39/100 mm). The multivariate logistic regression analysis revealed that the arrangement of the anterior teeth and the length of the denture are significantly associated with awareness of denture rotation. Thirty-eight percent in the R group and 31% in the NR group had non-scheduled visits. Rotational movement with a mandibular two-IOD has a negative effect on perceived chewing ability and is associated with anterior tooth arrangement and denture length.

Second molar impaction associated with lip bumper therapy

PubMed Central

Jacob, Helder Baldi; LeMert, Shawn; Alexander, Richard G.; Buschang, Peter H.

2014-01-01

INTRODUCTION: Although lip bumpers (LBs) provide significant clinical gain of mandibular arch perimeter in mixed-dentition patients, orthodontists are reluctant to use them due to the possibility of permanent second molar eruptive disturbances. OBJECTIVE: The present study was conducted to assess second molar impaction associated with the use of LBs, and to investigate how they can be solved. MATERIAL AND METHODS: Lateral and panoramic radiographs of 67 patients (34 females and 33 males) were assessed prior (T1) and post-LB treatment (T2). LB therapy lasted for approximately 1.8 ± 0.9 years. Concomitant rapid palatal expansion (RPE) was performed in the maxilla at LB treatment onset. Impaction of mandibular second molars was assessed by means of panoramic radiographs in relation to the position of first mandibular molars. Horizontal and vertical movements of first and second molars were assessed cephalometrically on lateral cephalometric radiographs based on mandibular superimpositions. RESULTS: Eight (11.9%) patients had impacted second molars at the end of LB therapy. Two patients required surgical correction, whereas five required spacers and one patient was self-corrected. Mandibular first molar tip and apex migrated forward 1.3 mm and 2.3 mm, respectively. Second molar tip showed no statistically significant horizontal movement. CONCLUSION: Although LB therapy increased the risk of second molar impaction, impactions were, in most instances, easily solved. PMID:25628086

Investigating the Use of Coherence Analysis on Mandibular Electromyograms to Investigate Neural Control of Early Oromandibular Behaviours: A Pilot Study

ERIC Educational Resources Information Center

Steeve, Roger W.; Price, Christiana M.

2010-01-01

An empirical method for investigating differences in neural control of jaw movement across oromandibular behaviours is to compute the coherence function for electromyographic signals obtained from mandibular muscle groups. This procedure has been used with adults but not extended to children. This pilot study investigated if coherence analysis…

Prevalence and Pattern of Mandibular Third Molar Impaction in Eritrean Population: A Retrospective Study.

PubMed

Kumar, V Raj; Yadav, Priya; Kahsu, Efrem; Girkar, Farhana; Chakraborty, Rajnish

2017-02-01

The most commonly impacted tooth in the oral cavity is the mandibular third molar. Various etiologic factors have been suggested for impacted mandibular third molars. The pattern and prevalence of impacted mandibular third molars vary with different population and region. This study throws light on the prevalence and pattern of impacted mandibular third molars in Eritrea, East Africa. This is the first reported study regarding the same from Eritrea. To assess the prevalence and pattern of impacted mandibu-lar third molars in the population of Eritrea, East Africa by conducting a retrospective study from January 2009 to January 2014. This study was conducted in the Department of Oral and Maxillofacial Surgery, Orotta School of Medicine and Dental Medicine and the Orotta Referral Medical and Surgical Hospital, Asmara, Eritrea. A total of 1,813 clinical and radiographic records [orthopantomograms] were assessed and 276 cases were selected for the study as per the inclusion criteria. They were evaluated for the frequency among the various age groups, gender and region along with the sides affected, angulation and level of impaction. The presence of systemic conditions and associated pathologies was also assessed according to the type of impaction. The average age of these patients in the study was found to be 30 years, with the 20 to 30 years age group being the most affected (67.4%). Females (53.3%) were affected more than the males (46.7%). People from the Asmara region showed significantly more prevalence (79.7%) than the adjoining areas (20.3%). Mesioangular impaction was the most common angulation with a definite relationship to the age groups (p = 0.032). The level of impaction had no significant relationship to the age groups, gender, or region, although class I position A was found to be the most common type. Mesioangular class I position A impac-tion showed an apparent relationship with underlying systemic conditions, but it was statistically insignificant. Mesioangular impaction was found to be associated with the most number of pathologies (p = 0.001). The prevalence of mandibular impaction was less in Eritrea (15.2%) compared with other populations. This study provides useful baseline data for the prevalence and pattern of mandibular impaction in the Eritrean population. This study throws light on the pattern, type, and frequency of mandibular impacted teeth as per age, sex, and region among the population of Eritrea.

[Maxillo-facial surgery in skeletal Class II: repercussions on the temporo-mandibular joints].

PubMed

Manière-Ezvan, Armelle; Savoldelli, Charles; Busson, Floriant; Oueiss, Arlette; Orthlieb, Jean-Daniel

2016-03-01

These interventions usually aimed at the correction of the skeletal discrepancy by mandibular retrognatism with an advancement of the distal portion of the mandible after mandibular osteotomy. The position of the condyle is determined during the osteosynthesis with miniplates. Condyles are set back in relation with the supine position of the patient and the weakness of his (her) curarized muscle. All studies show that surgery of mandibular advancement causes a lateral, torque and backward movement of the condyles, all harmful to the condyles. Factors that predispose to condylar resorption are "the patient": a woman, young (between 15 and 40), high mandibular angle, with a history of temporo-mandibular disorders and surgical overload applied to the condyles. What are the possible solutions to avoid failures? Patient preparation before surgery and surgery simulation with an articulator, condylar position control during surgery, working with surgeons to achieve a condylar portion stabilization system (with the CAD), quickly set up a mobilization of the mandible by physiotherapy. © EDP Sciences, SFODF, 2016.

Gender determination: Role of lip prints, finger prints and mandibular canine index

PubMed Central

KRISHNAN, RESHMA POOTHAKULATH; THANGAVELU, RADHIKA; RATHNAVELU, VIDHYA; NARASIMHAN, MALATHI

2016-01-01

Personal identification has a pivotal role in forensic investigations. Gender determination is an essential step in personal identification. Despite the advent of advanced techniques such as DNA fingerprinting, methods such as lip print and fingerprint analysis and mandibular canine index calculations are routinely used in gender determination, as they are simple and cost-effective. The present study investigated the hypothesis that lip print analysis is an effective tool in gender determination compared with fingerprint analysis and the mandibular canine index. The predominant patterns of lip prints and fingerprints were analyzed in males and females, and the efficacy of the mandibular canine index in gender determination was evaluated. The study group comprised 50 students, 25 males and 25 females who were 18–25 years of age. Lip prints and fingerprints were obtained and classified according to Tsuchihashi's classification and Kücken and Newell's classification, respectively. Mandibular impressions were made and the mandibular canine index was calculated. Type I and Type I' lip prints were predominant in females, and Type IV lip prints were predominant in males. The analysis of fingerprints revealed that the loop fingerprint pattern was predominant in both males and females. The mandibular canine index was not found to be significant in gender identification. The predominant patterns of lip prints were distinct for males and females; conversely, fingerprints were demonstrated to be similar in both genders. Therefore, lip prints hold an increased potential for gender determination, as compared with fingerprints, and the mandibular canine index is not a reliable indicator of gender. PMID:27284316

Incongruity between Affinity Patterns Based on Mandibular and Lower Dental Dimensions following the Transition to Agriculture in the Near East, Anatolia and Europe

PubMed Central

Pinhasi, Ron; Eshed, Vered; von Cramon-Taubadel, Noreen

2015-01-01

While it has been suggested that malocclusion is linked with urbanisation, it remains unclear as to whether its high prevalence began 8,000 years earlier concomitant with the transition to agriculture. Here we investigate the extent to which patterns of affinity (i.e., among-population distances), based on mandibular form and dental dimensions, respectively, match across Epipalaeolithic, Mesolithic, and Neolithic samples from the Near East/Anatolia and Europe. Analyses were conducted using morphological distance matrices reflecting dental and mandibular form for the same 292 individuals across 21 archaeological populations. Thereafter, statistical analyses were undertaken on four sample aggregates defined on the basis of their subsistence strategy, geography, and chronology to test for potential differences in dental and mandibular form across and within groups. Results show a clear separation based on mandibular morphology between European hunter-gatherers, European farmers, and Near Eastern transitional farmers and semi-sedentary hunter-gatherers. In contrast, the dental dimensions show no such pattern and no clear association between the position of samples and their temporal or geographic attributes. Although later farming groups have, on average, smaller teeth and mandibles, shape analyses show that the mandibles of farmers are not simply size-reduced versions of earlier hunter-gatherer mandibles. Instead, it appears that mandibular form underwent a complex series of shape changes commensurate with the transition to agriculture that are not reflected in affinity patterns based on dental dimensions. In the case of hunter-gatherers there is a correlation between inter-individual mandibular and dental distances, suggesting an equilibrium between these two closely associated morphological units. However, in the case of semi-sedentary hunter-gatherers and farming groups, no such correlation was found, suggesting that the incongruity between dental and mandibular form began with the shift towards sedentism and agricultural subsistence practices in the core region of the Near East and Anatolia. PMID:25651540

Variations in the branching pattern of posterior division of mandibular nerve: a case report.

PubMed

Muraleedharan, Aparna; Veeramani, Raveendranath; Chand, Parkash

2014-11-01

Abnormal communications among the branches of mandibular nerve especially the posterior division are significant due to various procedures undertaken in this region. These variations are worth reporting as they pose serious implications in several interventions in this region, and may even lead to false diagnosis. During routine dissection, the mandibular nerve and its branches were dissected in the infratemporal fossa. The branches from the posterior division of the mandibular nerve namely the inferior alveolar and auriculotemporal nerves were carefully dissected, and their abnormal branching pattern was noted. There was a communicating branch between left inferior alveolar and auriculotemporal nerve. There was also a variant recurrent branch from the left inferior alveolar nerve that supplied the lateral pterygoid muscle. Such variant branches and communications between the branches of mandibular nerve as seen in this case have an embryological basis and are clinically important in this region especially for dental surgeries and anesthesia.

Aspects of masticatory form and function in common tree shrews, Tupaia glis.

PubMed

Fish, D R

1983-04-01

Tree shrews have relatively primitive tribosphenic molars that are apparently similar to those of basal eutherians; thus, these animals have been used as a model to describe mastication in early mammals. In this study the gross morphology of the bony skull, joints, dentition, and muscles of mastication are related to potential jaw movements and cuspal relationships. Potential for complex mandibular movements is indicated by a mobile mandibular symphysis, shallow mandibular fossa that is large compared to its resident condyle, and relatively loose temporomandibular joint ligaments. Abrasive tooth wear is noticeable, and is most marked at the first molars and buccal aspects of the upper cheek teeth distal to P2. Muscle morphology is basically similar to that previously described for Tupaia minor and Ptilocercus lowii. However, in T. glis, an intraorbital part of deep temporalis has the potential for inducing lingual translation of its dentary, and the large medial pterygoid has extended its origin anteriorly to the floor of the orbit, which would enhance protrusion. The importance of the tongue and hyoid muscles during mastication is suggested by broadly expanded anterior bellies of digastrics, which may assist mylohyoids in tensing the floor of the mouth during forceful tongue actions, and by preliminary electromyography, which suggests that masticatory muscles alone cannot fully account for jaw movements in this species.

Temporo-mandibular joint kinetics and chewing cycles in children. A 3-year follow-up.

PubMed

Bodin, C; Lodetti, G; Marinone, M G

2002-01-01

To report the temporo-mandibular joint (TMJ) kinetics and masticatory function in healthy children. Temporo-mandibular joint palpation and electrognathographic registrations of chewing cycles were repeated for 3 years in order to evaluate changes. Healthy children without systemic pathologies, decayed cavities and previous dental treatment. Electrognathographic (EGN) registration of masticatory cycles and TMJ palpation were carried out on 52 patients (mean age: 5 years 8 months, range: 5 years 1 month, 6 years 8 months), by two university researchers, once a year for 3 consecutive years. TMJ palpation, differentiated TMJ synchronism (simultaneous bilateral opening movement) and TMJ asynchronism (not simultaneous bilateral opening movement), TMJ subluxation and click were observed. Electrognathographic registrations differentiated normal and abnormal jaw chewing cycles, and narrow and large cycles. Temporo-mandibular joint asynchronism was evident in 34 of 52 patients in the primary dentition, in 42 of 52 patients after the eruption of the first permanent molar, and in 31 of 52 patients after the eruption of the permanent incisors. TMJ subluxation increased during the full period of observation. Three temporomandibular clicks appeared after the eruption of the permanent incisors. Altered mastication was not always associated with TMJ disorders. In children, normal chewing cycles can coexist with occlusal discrepancies, cranio-facial growth and TMJ alterations.

Association between masticatory performance using a colour-changeable chewing gum and jaw movement.

PubMed

Komagamine, Y; Kanazawa, M; Minakuchi, S; Uchida, T; Sasaki, Y

2011-08-01

The purpose of this study was to investigate the relationship between masticatory performance as determined using a colour-changeable chewing gum and mandibular movements. Subjects comprised 45 fully dentate adults (23 men, 22 women; mean age, 28·1 years). The gum was chewed for a specified number of chewing strokes (20, 40, 60, 80, 120 or 160 strokes) without any instructions as to chewing side. A colourimeter was used to measure L*, a* and b* values (CIE-L*a*b* colour system) for the chewed gum, then the difference between two colours in the CIE-L*a*b* colour space (ΔE) for each number of chewing strokes was calculated according to a formula. Index of masticatory performance (ΔE60) for each subject was obtained using ΔE for 20, 40, 60, 80, 120 and 160 strokes. Mandibular movements were recorded using an opto-electric system with six degrees of freedom. Twelve parameters of mandibular movements relating to amplitude, duration, velocity and angle were computed for each cycle, and mean values for 10 cycles (from cycle 11 to 20) were calculated separately. Stepwise multiple regression analysis identified maximum closing velocity and closing angle as predictors accounting for 18% of the variation in ΔE60. These results suggest that lower angles of approach to intercuspation and faster speed during closing duration are associated with colour changes in the colour-changeable chewing gum. © 2011 Blackwell Publishing Ltd.

Mandibular Fracture Patterns at a Medical Center in Central Taiwan: A 3-Year Epidemiological Review.

PubMed

Lin, Fu-Yu; Wu, Chao-I; Cheng, Hsu-Tang

2017-12-01

Mandibular fractures constitute a major portion of maxillofacial trauma and may lead to considerable functional and aesthetic sequelae if treatment is inadequate or delayed. An epidemiology study on mandibular fractures may guide the preventive efforts of the Taiwan public health care system. Therefore, a retrospective review was conducted at a medical center in central Taiwan to evaluate the current mandibular fracture epidemiology.The medical records and digitized radiographs of 198 patients who received treatment for mandibular fractures during a 3-year period (from October 2010 to September 2013) at a medical center in central Taiwan were reviewed to obtain demographic and injury data.The average age was 29.4 years (3-82 years). Patients aged 21 to 30 years sustained the most mandibular fractures (62 patients, 31.3%). The overall sex distribution (male to female) ratio was 1.8. Motor-vehicle accidents (MVAs) were the most common mechanism of injury (162 patients, 82%), and scooter and motorcycle riders wearing partial-coverage helmets constituted the majority of patients. A chart review identified 198 patients with 335 mandibular fractures; 113 patients (57.1%) had multiple mandibular fractures. The most common fracture sites were the symphysis and parasymphysis regions (38.9%), followed by the condyle (26.0%), angle (14.3%), body (14.3%), and ramus (6.6%).MVAs are the major cause of mandibular fractures in central Taiwan, and patients aged <30 years sustained the most mandibular fractures. Compared with previous studies, the present study has a higher percentage of women with mandibular fractures. In addition, inadequate mandibular protection by partial-coverage helmets may be a major reason for mandibular fractures most commonly localized in the symphysis and parasymphysis regions. The incidence and causes of mandibular fractures may reflect the trauma patterns within the community, thus facilitating the development of a preventive strategy for the socioeconomic and environmental background of central Taiwan. Copyright © 2017 The Authors. Published by Wolters Kluwer Health, Inc. All rights reserved.

Overall intelligibility, articulation, resonance, voice and language in a child with Nager syndrome.

PubMed

Van Lierde, Kristiane M; Luyten, Anke; Mortier, Geert; Tijskens, Anouk; Bettens, Kim; Vermeersch, Hubert

2011-02-01

The purpose of this study was to provide a description of the language and speech (intelligibility, voice, resonance, articulation) in a 7-year-old Dutch speaking boy with Nager syndrome. To reveal these features comparison was made with an age and gender related child with a similar palatal or hearing problem. Language was tested with an age appropriate language test namely the Dutch version of the Clinical Evaluation of Language Fundamentals. Regarding articulation a phonetic inventory, phonetic analysis and phonological process analysis was performed. A nominal scale with four categories was used to judge the overall speech intelligibility. A voice and resonance assessment included a videolaryngostroboscopy, a perceptual evaluation, acoustic analysis and nasometry. The most striking communication problems in this child were expressive and receptive language delay, moderately impaired speech intelligibility, the presence of phonetic and phonological disorders, resonance disorders and a high-pitched voice. The explanation for this pattern of communication is not completely straightforward. The language and the phonological impairment, only present in the child with the Nager syndrome, are not part of a more general developmental delay. The resonance disorders can be related to the cleft palate, but were not present in the child with the isolated cleft palate. One might assume that the cul-de-sac resonance and the much decreased mandibular movement and the restricted tongue lifting are caused by the restricted jaw mobility and micrognathia. To what extent the suggested mandibular distraction osteogenesis in early childhood allows increased mandibular movement and better speech outcome with increased oral resonance is subject for further research. According to the results of this study the speech and language management must be focused on receptive and expressive language skills and linguistic conceptualization, correct phonetic placement and the modification of hypernasality and nasal emission. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Morphological Integration of the Modern Human Mandible during Ontogeny

PubMed Central

Polanski, Joshua M.

2011-01-01

Craniofacial integration is prevalent in anatomical modernity research. Little investigation has been done on mandibular integration. Integration patterns were quantified in a longitudinal modern human sample of mandibles. This integration pattern is one of modularization between the alveolar and muscle attachment regions, but with age-specific differences. The ascending ramus and nonalveolar portions of the corpus remain integrated throughout ontogeny. The alveolar region is dynamic, becoming modularized according to the needs of the mandible at a particular developmental stage. Early in ontogeny, this modularity reflects the need for space for the developing dentition; later, modularity is more reflective of mastication. The overall pattern of modern human mandibular integration follows the integration pattern seen in other mammals, including chimpanzees. Given the differences in craniofacial integration patterns between humans and chimpanzees, but the similarities in mandibular integration, it is likely that the mandible has played the more passive role in hominin skull evolution. PMID:21716741

An Epidemiological Study on Pattern and Incidence of Mandibular Fractures

PubMed Central

Natu, Subodh S.; Pradhan, Harsha; Gupta, Hemant; Alam, Sarwar; Gupta, Sumit; Pradhan, R.; Mohammad, Shadab; Kohli, Munish; Sinha, Vijai P.; Shankar, Ravi; Agarwal, Anshita

2012-01-01

Mandible is the second most common facial fracture. There has been a significant increase in the number of cases in recent years with the advent of fast moving automobiles. Mandibular fractures constitute a substantial proportion of maxillofacial trauma cases in Lucknow. This study was undertaken to study mandibular fractures clinicoradiologically with an aim to calculate incidence and study pattern and the commonest site of fractures in population in and around Lucknow. Patient presenting with history of trauma at various centers of maxillofacial surgery in and around Lucknow were included in this study. Detailed case history was recorded followed by thorough clinical examination, and radiological interpretation was done for establishing the diagnosis and the data obtained was analyzed statistically. Out of 66 patients with mandibular fractures, highest percentage was found in 21–30 years of age with male predominance. Road traffic accidents were the most common cause of fracture with parasymphysis being commonest site. Commonest combination was parasymphysis with subcondyle. There was no gender bias in etiology with number of fracture sites. The incidence and causes of mandibular fracture reflect trauma patterns within the community and can provide a guide to the design of programs geared toward prevention and treatment. PMID:23227327

Orthodontic treatment for oral rehabilitation after multiple maxillofacial bone fractures.

PubMed

Nakamura, Yoshiki; Ogino, Tomoko Kuroiwa; Hirashita, Ayao

2008-09-01

We present the orthodontic treatment of a patient with occlusal dysfunction after plastic surgery for multiple maxillofacial bone fractures caused by a traffic accident. The patient had mandibular deviation to the right because of inappropriate repositioning and fixation of the fractured bone and complete avulsion of both mandibular central incisors. The bilateral mandibular incisors, canines, and premolars were also suspected of partial avulsion or alveolar bone fracture. Several tests, including percussion and dental computed tomography, were performed on these teeth to rule out ankylosis and confirm tooth movement. Camouflage orthodontic treatment was carried out with expansion of the maxillary arch, alignment of both arches, and space closure between the mandibular lateral incisors to improve the occlusion. Good occlusion and interdigitation were obtained. Orthodontic treatment is useful for the rehabilitation of occlusal dysfunction caused by multiple maxillofacial bone fractures.

Exclusion of pituitary homeobox 2 gene polymorphism in vertical mandibular asymmetry patients: a preliminary study

NASA Astrophysics Data System (ADS)

Sofyanti, Ervina; Boel, Trelia; Soegiharto, Benny; Ilyas, Syafruddin; Irani Nainggolan, Lidya; Auerkari, Elza Ibrahim

2018-03-01

Pituitary Homeobox 2 (PITX2), is an active gene as a paired-related homeobox gene that encodes multiple isoforms. Its Nodal pathway in determination of left-right patterning during embryogenesis has been reported in satellite cells and expressed in adult human skeletal muscle. PITX2A and PITX2B are produced by alternative splicing and used of different promoters. PITX2C uses an alternative promoter located upstream of exon 4. PITX2D is produced by PITX2C alternative promoter and differential splicing. The 5’-primers and 3’- antisense primer were unique for each isoforms. Variability measurement in vertical dimension showed stronger genetic component than sagittal. This study aims to obtain the genotype marker of vertical mandibular asymmetry related to PITX2A and PITX2D isoform by visualization of the amplified product on stained gel to allele specific oligonucleotide between the case and control with Restriction Fragment Length Polymorphism (RFLP). Determination of vertical mandibular asymmetry based on condylar height asymmetry index of pre-treatment panoramic radiograph using Kjellberg’s technique whilst vertical mandibular growth pattern using lateral cephalogram. The differences of condylar height asymmetry in case-control based on vertical growth pattern was compared using Pearson’s chi-squared test. DNA extraction of 129 out-coming orthodontic patients in Universitas Sumatera Utara Dental Hospital were obtained from Buccal swab. Then DNA samples were amplified by Polymerase chain reaction (PCR) and digested with NciI restriction enzyme prior to electrophoresis visualization. There was no significant statistical difference in vertical mandibular asymmetry compared to vertical mandibular growth pattern. The RFLP analysis did not show any polymorphism for PITX2A and PITX2D isoform. All of the samples showed wild type homozygote. Further analysis method, except RFLP, were required to understand the genetic factor in the variance of vertical mandibular asymmetry.

Correction of a mutilated dentition with mini-implants as anchorage.

PubMed

Hyun, Jae-Man; Kim, Tae-Woo

2010-11-01

The patient was an adolescent boy, aged 15.6 years, with a mutilated dentition. He had extrusion of the maxillary left first molar because of loss of the mandibular first molar and lingual tilting and rotation of the mandibular second molars. Both left and right second molars were in scissors-bite that was more severe on the left side. By using mini-implants and a TPA with hooks, a 3-mm intrusion was successfully made on the maxillary left first molar. This provided room for mesial movement of the mandibular left second molar. The second molar was protracted into the space of the missing first molar, and the mandibular left third molar was positioned in place of the second molar. The second molars scissors-bite was corrected. Active treatment took 45 months, and the treatment result remained stable 2 years after debonding. Copyright © 2010 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Signaling pathways regulating the expression of Prx1 and Prx2 in the Chick Mandibular Mesenchyme

PubMed Central

Doufexi, Aikaterini-El; Mina, Mina

2009-01-01

Prx1 and Prx2 are members of the aristaless-related homeobox genes shown to play redundant but essential roles in morphogenesis of the mandibular processes. To gain insight into the signaling pathways that regulate expression of Prx genes in the mandibular mesenchyme, we used the chick as a model system. We examined the patterns of gene expression in the face and the roles of signals derived from the epithelium on the expression of Prx genes in the mandibular mesenchyme. Our results demonstrated stage-dependent roles of mandibular epithelium on the expression of Prx in the mandibular mesenchyme and provide evidence for positive roles of members of the fibroblast and hedgehog families derived from mandibular epithelium on the expression of Prx genes in the mandibular mesenchyme. Our studies suggest that endothelin-1 signaling derived from the mesenchyme is involved in restricting the expression of Prx2 to the medial mandibular mesenchyme. PMID:18942149

[Extramedullary fixation combined with intramedullary fixation in the surgical reduction of sagittal mandibular condylar fractures].

PubMed

Chuanjun, Chen; Xiaoyang, Chen; Jing, Chen

2016-10-01

This study aimed to evaluate the clinical effect of extramedullary fixation combined with intramedullary fixation during the surgical reduction of sagittal mandibular condylar fractures. Twenty-four sagittal fractures of the mandibular condyle in18 patients were fixed by two appliances: intramedullary with one long-screw osteosynthesis or Kirschner wire and extramedullary with one micro-plate. The radiologically-recorded post-operative stability-associated com-plications included the screw/micro-plate loosening, micro-plate twisting, micro-plate fractures, and fragment rotation. The occluding relations, the maximalinter-incisal distances upon mouth opening, and the mandibular deflection upon mouth opening were evaluated based on follow-up clinical examination. Postoperative panoramic X-ray and CT scans showed good repositioning of the fragment, with no redislocation or rotation, no screw/plate loosening, and no plate-twisting or fracture. Clinical examination showed that all patients regained normal mandibular movements, ideal occlusion, and normal maximal inter-incisal distances upon mouth opening. Extramedullary fixation combined with intramedullary fixation is highly recommended for sagittal condylar fractures because of the anti-rotation effect of the fragment and the reasonable place-ment of the fixation appliances.

Effect of pacifier use on mandibular position in preterm infants.

PubMed

Tonkin, Shirley L; Lui, Dana; McIntosh, Christine G; Rowley, Simon; Knight, David B; Gunn, Alistair J

2007-10-01

It has been hypothesized that the association of pacifier use with reduced risk of sudden infant death is mediated by forward movement of the mandible and tongue that helps open the upper airway. Our aim was to examine whether the mandible is moved forward when an infant is sucking on a pacifier, and if so, whether the mandible remains advanced after the pacifier is removed. In sixty clinically stable premature infants (corrected gestation age 36.5 +/- 0.3 weeks, mean +/- SEM) the distance from each ear where the pinna met the cheek to the most prominent point of the chin was measured bilaterally, and the average was used as an index of mandibular position. Mandibular position was determined before and after allowing the infants to suck on a pacifier for 10-15 min, and after removing the pacifier. There was a significant forward movement of the mandible when the infants were sucking on the pacifier (59.5 +/- 0.7 vs. 58.6 +/- 0.7 mm, p = 0.001), with no significant change after the pacifier was removed. Pacifier use in preterm infants was associated with a small significant forward displacement of the jaw. These data suggest that pacifier use may help protect the upper airway.

[Clinical analysis of caries status of the mandibular second molar].

PubMed

You, Chun-an; Zheng, Ping; Hu, Ning; Su, Qin

2014-04-01

To collect the cases which have caries on the mandibular second molar and analyze the caries status and correlative factors. Patients treated in the Department of Endodontics in West China Hospital of Stomatology were randomly collected. The baseline information, primary sites and severity of dental caries on the mandibular second molar, and eruption pattern of the mandibular third molar were recorded. The data was analyzed with SPSS13.0 software package. Four hundred eighty-one patients including 227 males and 254 females were collected. Caries on the mandibular second molar starting from the occlusal, distal proximal and buccal surfaces accounted for 33.8%, 33.2% and 24.4%, respectively. Caries involving dental pulp (49.7%) were significantly more than deep and shallow to moderate caries (31.7% and 18.6%). Gender was not correlated with the site and severity of caries. However, impacted mandibular third molars and age were significantly related to both caries site and severity. Occlusal and distal proximal surfaces are the most predisposed sites to have caries on mandibular second molar. Impacted mandibular third molar and age are significantly related to caries of mandibular second molar.

Mandibular fracture patterns consistent with posterior maxillary fractures involving the posterior maxillary sinus, pterygoid plate or both: CT characteristics.

PubMed

Imai, T; Sukegawa, S; Kanno, T; Fujita, G; Yamamoto, N; Furuki, Y; Michizawa, M

2014-01-01

The aim of this study was to determine the incidence of posterior maxillary fractures involving the posterior maxillary sinus wall, pterygoid plate or both, unrelated to major midface fractures in patients with mandibular fractures, and to characterize associated fractures. A CT study was performed in patients with mandibular fractures to identify posterior maxillary fractures. Patients aged under 16 years, those with mandibular fractures involving only dentoalveolar components and those with concurrent major midfacial fractures were excluded. 13 (6.7%) of 194 patients with mandibular fractures also had posterior maxillary fractures (case group). The injury pattern correlated with the external force directed to the lateral side of the mandible (p < 0.001), alcohol consumption (p = 0.049), the presence of multifocal fractures (p = 0.002) and the fracture regions in the symphysis/parasymphysis (p = 0.001) and the angle/ramus (p = 0.001). No significant difference between the case and non-case groups was seen for age, sex or cause of trauma. Non-displaced fractures in the ipsilateral posterior mandible occurred with significant frequency (p = 0.001) when the posterior maxillary fractures involved only the sinus. Mandibular fractures accompanied by posterior maxillary fractures are not rare. The finding of a unilateral posterior maxillary fracture on CT may aid the efficient radiological examination of the mandible based on possible patterns of associated fractures, as follows: in the ipsilateral posterior region as a direct fracture when the impact is a medially directed force, and in the symphysis/parasymphysis or contralateral condylar neck as an indirect fracture.

Changes in maxillofacial morphology and velopharyngeal function with two-stage maxillary distraction-mandibular setback surgery in patients with cleft lip and palate.

PubMed

Susami, T; Mori, Y; Ohkubo, K; Takahashi, M; Hirano, Y; Saijo, H; Takato, T

2018-03-01

Maxillary distraction is increasingly used for the correction of severe maxillary retrusion in patients with cleft lip and palate. However, control of the maxillary movement is difficult, and the need to wear visible distractors for a long period of time causes psychosocial problems. A two-stage surgical approach consisting of maxillary distraction and mandibular setback was developed to overcome these problems. In this study, changes in maxillofacial morphology and velopharyngeal function were examined in 22 patients with cleft lip and palate who underwent this two-stage approach. Lateral cephalograms taken just before the first surgery, immediately after the second surgery, and at completion of the active post-surgical orthodontic treatment were used to examine maxillofacial morphology. Velopharyngeal function was evaluated by speech therapists using a 4-point scale for hypernasality. The average forward movement of the maxilla with surgery at point A was 7.5mm, and the average mandibular setback at pogonion was 8.6mm. The average relapse rate during post-surgical orthodontic treatment was 25.2% for the maxilla and 11.2% for the mandible. After treatment, all patients had positive overjet, and skeletal relapse was covered by tooth movement during postoperative orthodontics. Velopharyngeal function was not changed by surgery. This method can shorten the period during which the distractors have to be worn and reduce the patient burden. Copyright © 2017 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Treatment effects of a fixed intermaxillary device to correct class II malocclusions in growing patients.

PubMed

Heinrichs, Dean A; Shammaa, Imad; Martin, Chris; Razmus, Thomas; Gunel, Erdogan; Ngan, Peter

2014-01-01

The objective of this study was to evaluate the treatment effects of Forsus™ Fatigue Resistant Device (FRD; 3M Unitek, Monrovia, CA, USA) in growing patients with Class II non-extraction malocclusions. A retrospective sample of 24 class II patients treated consecutively with the FRD followed by comprehensive orthodontic treatment was compared to a sample of untreated control subjects from the Bolton Brush Study who was matched in age, sex, and craniofacial morphology. Lateral cephalometric radiographs were taken before treatment (T1) and after removal of fixed appliances (T2). Growth changes were subtracted from the treatment changes to obtain the treatment effects of the appliance. Data were analyzed using ANOVA and a match paired t test. Significant differences were found between the treated and control groups for 12 of the 29 measured variables (Co-Gn minus Co-Apt, Wits, Is-OLp, Ii-OLp, overjet, Mi-OLp, molar relationship, overbite, Mic-ML, SNA, ANB, and Ii-ML). With 27.8 months of treatment, all patients were corrected to a class I dental arch relationship. Overjet and molar relationships were improved by an average of 4.7 and 3.1 mm, respectively. This was contributed by a 1.2 mm of restraint in forward maxillary growth, 0.7 mm of forward movement of the mandible, 1.5 mm of backward movement of the maxillary incisors, 1.3 mm forward movement of the mandibular incisors, 0.5 mm backward movement of the maxillary molars, and 1.3 mm of forward movement of the mandibular molars. The overbite was decreased by 2 mm with no significant change in the occlusal, palatal, or mandibular plane. Individual variations in response to the FRD treatment were large for most of the parameters tested. Significant differences in treatment changes between male and female subjects were found only in a few parameters measured. These results demonstrate that significant overjet and overbite corrections can be obtained with the Forsus FRD in conjunction with comprehensive orthodontic treatment.

[Bruxism, temporo-mandibular dysfunction and botulinum toxin].

PubMed

Chikhani, L; Dichamp, J

2003-07-01

Tooth grinding and tooth clenching are unvoluntary mainly nocturnal habits that result in an hypertrophy of masseter and temporalis muscles with an unbalance between opening and closing muscles of the jaw and lead to an alteration of mandibular condyles movements and to hyper pressure in the temporo-mandibular joints (TMJ) which can generate severe pain. Intra muscular injections of botulinum toxin permit to restablish the balance between closing and opening muscles, to relieve pain, to treat masseteric hypertrophy with improvement of face outline and to recover a normal cinetic of temporo-mandibular joints. Moreover, botulinum toxin injections permit to quit habits of tooth grinding and clenching and one single session of injections is curative for 2/3 of the patients. There are no side effects apart from slight diffusion to superficial muscles of the face resulting in a "fixed" smile for about 6 to 8 weeks. So injections of botulinum toxin in masseter and temporalis muscles are an efficient treatment of bruxism and TMJ dysfunction, cheap with no lasting side effect.

Patterns of mandibular variation in Pan and Gorilla and implications for African ape taxonomy.

PubMed

Taylor, Andrea B; Groves, Colin P

2003-05-01

Pan and Gorilla taxonomy is currently in a state of flux, with the number of existing species and subspecies of common chimpanzee and gorilla having been recently challenged. While Pan and Gorilla systematics have been evaluated on the basis of craniometric and odontometric data, only a handful of studies have evaluated multivariate craniometric variation within P. troglodytes, and none have evaluated in detail mandibular variation in either P. troglodytes or Gorilla gorilla. In this paper, we examine ontogenetic and adult mandibular variation in Pan and Gorilla. We test the hypothesis that patterns and degrees of mandibular variation in Pan and Gorilla closely correspond to those derived from previous analyses of craniometric variation. We then use these data to address some current issues surrounding Pan and Gorilla taxonomy. Specifically, we evaluate the purported distinctiveness of P.t. verus from the other two subspecies of Pan troglodytes, and the recent proposals to recognize Nigerian gorillas as a distinct subspecies, Gorilla gorilla diehli, and to acknowledge mountain and lowland gorillas as two separate species. Overall, patterns and degrees of multivariate mandibular differentiation parallel those obtained previously for the cranium and dentition. Thus, differences among the three conventionally recognized gorilla subspecies are somewhat greater than among subspecies of common chimpanzees, but differences between P. paniscus and P. troglodytes are greater than those observed between any gorilla subspecies. In this regard, the mandible does not appear to be more variable, or of less taxonomic value, than the face and other parts of the cranium. There are, however, some finer differences in the pattern and degree of morphological differentiation in Pan and Gorilla, both with respect to cranial and dental morphology, and in terms of the application and manner of size adjustment. Mandibular differentiation supports the conventional separation of bonobos from chimpanzees regardless of size adjustment, but size correction alters the relative alignment of taxa. Following size correction, intergroup distances are greatest between P.t. verus and all other groups, but there is considerable overlap amongst chimpanzee subspecies. Amongst gorillas, the greatest separation is between eastern and western gorillas, but adjustment relative to palatal vs. basicranial length results in a greater accuracy of group classification for G.g. gorilla and G.g. graueri, and more equivalent intergroup distances amongst all gorilla groups. We find no multivariate differentiation of the Nigerian gorillas based on mandibular morphology, suggesting that the primary difference between Nigerian and other western lowland gorillas lies in the nuchal region. Though intergroup distances are greatest between P.t. verus and other chimpanzee subspecies, the degree of overlap amongst all three groups does not indicate a markedly greater degree of distinction in mandibular, as opposed to other morphologies. Finally, mandibular differentiation corroborates previous craniodental studies indicating the greatest distinction amongst gorillas is between eastern and western groups. Thus, patterns and degrees of mandibular variation are in agreement with other kinds of data that have been used to diagnose eastern and western gorillas as separate species.

Relationship between cervical vertebral maturation and mandibular growth.

PubMed

Ball, Gina; Woodside, Donald; Tompson, Bryan; Hunter, W Stuart; Posluns, James

2011-05-01

The cervical vertebrae have been proposed as a method of determining biologic maturity. The purposes of this study were to establish a pattern of mandibular growth and to relate this pattern to the stages of cervical vertebral maturation. Cephalometric radiographs, taken annually from ages 9 to 18 years, were evaluated for 90 boys from the Burlington Growth Center, Toronto, Ontario, Canada. Mandibular lengths were measured from articulare to gnathion, and incremental growth was determined. Cervical vertebral maturation stages were assessed by using a 6-stage method. Advanced, average, and delayed maturation groups were established. The prepubertal mandibular growth minimum velocity occurred during cervical stages 1 through 4 (P = 0.7327). Peak mandibular growth velocity occurred most frequently during stage 4 in all 3 maturation groups, with a statistical difference in the average and delayed groups (P <0.0001) and the advanced group (P = 0.0143). The average number of years spent in stage 4 was 3.79 (P <0.0001). The average amount of mandibular growth occurring during stage 4 was 9.40 mm (P <0.0001). The average amount of growth in stages 5 and 6 combined was 7.09 mm. Progression from cervical stages 1 through 6 does not occur annually; time spent in each stage varies depending on the stage and the maturation group. Cervical vertebral maturation stages cannot accurately identify the mandibular prepubertal growth minimum and therefore cannot predict the onset of the peak in mandibular growth. The cervical vertebral maturation stages should be used with other methods of biologic maturity assessment when considering both dentofacial orthopedic treatment and orthognathic surgery. Copyright © 2011 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Mandibular fracture patterns consistent with posterior maxillary fractures involving the posterior maxillary sinus, pterygoid plate or both: CT characteristics

PubMed Central

Sukegawa, S; Kanno, T; Fujita, G; Yamamoto, N; Furuki, Y; Michizawa, M

2014-01-01

Objectives: The aim of this study was to determine the incidence of posterior maxillary fractures involving the posterior maxillary sinus wall, pterygoid plate or both, unrelated to major midface fractures in patients with mandibular fractures, and to characterize associated fractures. Methods: A CT study was performed in patients with mandibular fractures to identify posterior maxillary fractures. Patients aged under 16 years, those with mandibular fractures involving only dentoalveolar components and those with concurrent major midfacial fractures were excluded. Results: 13 (6.7%) of 194 patients with mandibular fractures also had posterior maxillary fractures (case group). The injury pattern correlated with the external force directed to the lateral side of the mandible (p < 0.001), alcohol consumption (p = 0.049), the presence of multifocal fractures (p = 0.002) and the fracture regions in the symphysis/parasymphysis (p = 0.001) and the angle/ramus (p = 0.001). No significant difference between the case and non-case groups was seen for age, sex or cause of trauma. Non-displaced fractures in the ipsilateral posterior mandible occurred with significant frequency (p = 0.001) when the posterior maxillary fractures involved only the sinus. Conclusions: Mandibular fractures accompanied by posterior maxillary fractures are not rare. The finding of a unilateral posterior maxillary fracture on CT may aid the efficient radiological examination of the mandible based on possible patterns of associated fractures, as follows: in the ipsilateral posterior region as a direct fracture when the impact is a medially directed force, and in the symphysis/parasymphysis or contralateral condylar neck as an indirect fracture. PMID:24336313

[Comparative effectiveness of surgical and non-surgical treatment for pediatric mandibular condylar fractures].

PubMed

Hu, Min; Wang, Yanyi; Zhang, Lihai; Yao, Jun

2010-12-01

To compare the effectiveness of open reduction and conservative treatment for pediatric mandibular condylar fractures and to provide the evidence for the selection of clinical therapy. The clinical data were retrospectively analyzed from 25 patients with the mandibular condylar fractures between January 1988 and December 2006. Of them, 8 patients (11 fractures) were treated with surgical treatment (surgical group) and 17 patients (22 fractures) with non-surgical treatment (non-surgical group). In surgical group, there were 6 males (9 fractures) and 2 females (2 fractures) with an age range of 8-13 years; fracture was caused by tumbling in 7 cases and by traffic accident in 1 with an interval of 1-6 days between injury and hospitalization; and 5 cases were identified as unilateral condylar fractures (3 complicated by mental fractures) and 3 cases as bilateral condylar fractures complicated by mental fractures. In non-surgical group, there were 12 males (15 fractures) and 5 females (7 fractures) with an age range of 3-12 years; fracture was caused by falling from height in 4 cases, by tumbling in 10, and by traffic accident in 3 with an interval of 1-25 days between injury and hospitalization; and 12 cases were identified as unilateral condylar fractures (3 complicated by mental fractures) and 5 cases as bilateral condylar fractures (1 complicated by mental fracture). Incision healed by first intention in surgical group, and 25 cases were followed up 1-6 years with an average of 3.5 years. At 12 months after treatment, no temporomandibular joint pain, eating disorder, or limited mandibular movement occurred in 2 groups. No significant difference was observed in opening mouth extent, protrusive and lateral movements between 2 groups at 6 and 12 months (P > 0.05). During centric occlusion, mental point located at the midline with symmetric face figure. Two patients in surgical group and 3 in non-surgical group had slight snap when opening their mouths. Mandible deviation was observed in 3 patients of 2 groups, respectively when gaping. The X-ray films showed healing of fracture and condylar remodeling at 3-6 months. Mandibular ramus were symmetric in cephalometry. Good effectiveness can be obtained by surgical or non-surgical treatment in pediatric mandibular condylar fractures. Considering the pediatric mandibular condyle having powerful healing and reconstructing potency and avoiding secondary injury on the temporomandibular joint from surgery, non-surgical treatment should be first selected for the pediatric mandibular condylar fractures in patients under 7 years.

Occlusal force, electromyographic activity of masticatory muscles and mandibular flexure of subjects with different facial types

PubMed Central

CUSTODIO, William; GOMES, Simone Guimarães Farias; FAOT, Fernanda; GARCIA, Renata Cunha Matheus Rodrigues; DEL BEL CURY, Altair Antoninha

2011-01-01

Objective The aim of this study was to evaluate whether vertical facial patterns influence maximal occlusal force (MOF), masticatory muscle electromyographic (EMG) activity, and medial mandibular flexure (MMF). Material and Methods Seventy-eight dentate subjects were divided into 3 groups by Ricketts's analysis: brachyfacial, mesofacial and dolychofacial. Maximum occlusal force in the molar region was bilaterally measured with a force transducer. The electromyographic activities of the masseter and anterior temporal muscles were recorded during maximal voluntary clenching. Medial mandibular flexure was calculated by subtracting the intermolar distance of maximum opening or protrusion from the distance in the rest position. The data were analyzed using ANOVA followed by Tukey's HSD test. The significance level was set at 5%. Results Data on maximum occlusal force showed that shorter faces had higher occlusal forces (P<0.0001). Brachyfacial subjects presented higher levels of masseter electromyographic activity and medial mandibular flexure, followed by the mesofacial and dolychofacial groups. Additionally, dolychofacial subjects showed significantly lower electromyographic temporalis activities (P<0.05). Conclusion Within the limitations of the study, it may be concluded that maximum occlusal force, masticatory muscle activity and medial mandibular flexure were influenced by the vertical facial pattern. PMID:21655772

Worn is born: The role of the maxillo-mandibular relation in management of worn dentition.

PubMed

Li, Zhongjie; Yang, Zheng; Lan, Tingting; Zhao, Hanchi; Liu, Yang

2017-07-01

Worn dentition, often accompanied by occlusion changes such as reduced vertical dimension, poses a big challenge to both diagnosis and treatment. Current established causes fail to explain the observed tooth wearing patterns, and the treatments based on the documented pathogeneses are often unpredictable and require frequent maintenance. From the perspective of stomatognathic system, we postulate that the role of maxillo-mandibular relation is a crucial part in the tooth wear progression patterns, and should be well addressed in treatment planning. Incompatible occlusion with the inherent tendency of maxillo-mandibular relation has a profound effect on either wearing of natural teeth or failures of restorations. With the aid of cephalometrics and analysis of occlusion it is now possible to reduce this fallacy and achieve a harmony by re-designing the occlusion. According to our treated worn dentition cases, the restoring treatment guided by the tendency of maxillo-mandibular relation showed very promising results. Copyright © 2017 Elsevier Ltd. All rights reserved.

Lower incisor dentoalveolar compensation and symphysis dimensions among Class I and III malocclusion patients with different facial vertical skeletal patterns.

PubMed

Molina-Berlanga, Núria; Llopis-Perez, Jaume; Flores-Mir, Carlos; Puigdollers, Andreu

2013-11-01

To compare lower incisor dentoalveolar compensation and mandible symphysis morphology among Class I and Class III malocclusion patients with different facial vertical skeletal patterns. Lower incisor extrusion and inclination, as well as buccal (LA) and lingual (LP) cortex depth, and mandibular symphysis height (LH) were measured in 107 lateral cephalometric x-rays of adult patients without prior orthodontic treatment. In addition, malocclusion type (Class I or III) and facial vertical skeletal pattern were considered. Through a principal component analysis (PCA) related variables were reduced. Simple regression equation and multivariate analyses of variance were also used. Incisor mandibular plane angle (P < .001) and extrusion (P  =  .03) values showed significant differences between the sagittal malocclusion groups. Variations in the mandibular plane have a negative correlation with LA (Class I P  =  .03 and Class III P  =  .01) and a positive correlation with LH (Class I P  =  .01 and Class III P  =  .02) in both groups. Within the Class III group, there was a negative correlation between the mandibular plane and LP (P  =  .02). PCA showed that the tendency toward a long face causes the symphysis to elongate and narrow. In Class III, alveolar narrowing is also found in normal faces. Vertical facial pattern is a significant factor in mandibular symphysis alveolar morphology and lower incisor positioning, both for Class I and Class III patients. Short-faced Class III patients have a widened alveolar bone. However, for long-faced and normal-faced Class III, natural compensation elongates the symphysis and influences lower incisor position.

The Predentary Bone and Its Significance in the Evolution of Feeding Mechanisms in Ornithischian Dinosaurs.

PubMed

Nabavizadeh, Ali; Weishampel, David B

2016-10-01

The characteristic predentary bone in ornithischian dinosaurs is a unique, unpaired element located at the midline of the mandibular symphysis. Although traditionally thought to only be a plant "nipping" bone, the true functional significance of this bone among feeding mechanisms of ornithischian dinosaurs is poorly known. Recent studies of a select few ornithischian genera have suggested rotation of the mandibular corpora around their long axes relative to their midline joint articulation with the predentary bone. This study aims to re-evaluate these hypotheses as well as provide in-depth qualitative comparative descriptions of predentary bone morphology in ornithischian genera throughout all subclades, including heterodontosaurids, thyreophorans, ornithopods, and marginocephalians. Descriptions evaluate overall shape of the predentary, its articular surfaces contacting the rostral ends of the dentaries, and the morphology of the rostral extent of the dentaries and their midline symphysis. Functionally relevant morphologies in each predentary morphotype are accentuated for further speculation of feeding mechanisms. Three predentary morphotypes are described throughout ornithischian subclades and each plays a unique role in feeding adaptations. Most notably, the predentary likely evolved as a midline axial point of the mandibular symphysis for simultaneous variable movement or rotation of the mandibular corpora in many, but not all, taxa. This simultaneous movement of the hemimandibles would have aided in feeding on both sides of the jaw at once. The function of the predentary as well as other jaw adaptations is discussed for genera throughout all subclades, focusing on both general shape and joint morphology. Anat Rec, 299:1358-1388, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Analysis of two different surgical approaches for fractures of the mandibular condyle.

PubMed

Kumaran, S; Thambiah, L J

2012-01-01

Fractures of the condyle account for one third of all the mandibular fractures. Different surgical approaches to the condyle described hitherto testify to the advantages and disadvantages of the different surgical techniques used for approaching the condyle in such cases of fractures. We have described and compared two of such surgical techniques in this study. The aim of this study is to compare the outcome of dealing with condylar fractures by two different surgical techniques: the mini retromandibular approach, and the preauricular approach. A prospective study of 31 patients who had suffered with mandibular condylar fractures was carried out. Of these, 26 patients had unilateral condylar fractures, and 5 patients had a bilateral fracture. Further, 19 of these patients were treated by the mini retromandibular approach and 12 by the preauricular approach. The treated patients were followed up and evaluated for a minimum period of 1 year and assessed for parameters such as the maximum mouth opening, lateral movement on the fractured side, mandibular movements such as protrusion, dental occlusion, scar formation, facial nerve weakness, salivary fistula formation and time taken for the completion of the surgical procedure. t- test was used for statistical analysis of the data obtained in the study. Dental occlusion was restored in all the cases, and good anatomical reduction was achieved. The mean operating time was higher 63.53 (mean) ± 18.12 minutes standard deviation (SD) in the preauricular approach compared to 45.22 (mean) ± 18.86 minutes SD in the mini retromandibular approach. Scar formation was satisfactory in almost all the cases.

Functional and morphological correlates of mandibular symphyseal form in a living human sample.

PubMed

Holton, Nathan E; Franciscus, Robert G; Ravosa, Matthew J; Southard, Thomas E

2014-03-01

Variation in recent human mandibular form is often thought to reflect differences in masticatory behavior associated with variation in food preparation and subsistence strategies. Nevertheless, while mandibular variation in some human comparisons appear to reflect differences in functional loading, other comparisons indicate that this relationship is not universal. This suggests that morphological variation in the mandible is influenced by other factors that may obscure the effects of loading on mandibular form. It is likely that highly strained mandibular regions, including the corpus, are influenced by well-established patterns of lower facial skeletal integration. As such, it is unclear to what degree mandibular form reflects localized stresses incurred during mastication vs. a larger set of correlated features that may influence bone distribution patterns. In this study, we examine the relationship between mandibular symphyseal bone distribution (i.e., second moments of area, cortical bone area) and masticatory force production (i.e., in vivo maximal bite force magnitude and estimated symphyseal bending forces) along with lower facial shape variation in a sample of n = 20 living human male subjects. Our results indicate that while some aspects of symphyseal form (e.g., wishboning resistance) are significantly correlated with estimates of symphyseal bending force magnitude, others (i.e., vertical bending resistance) are more closely tied to variation in lower facial shape. This suggests that while the symphysis reflects variation in some variables related to functional loading, the complex and multifactorial influences on symphyseal form underscores the importance of exercising caution when inferring function from the mandible especially in narrow taxonomic comparisons. Copyright © 2013 Wiley Periodicals, Inc.

Pattern of mandibular third molar impaction and its association to caries in mandibular second molar: A clinical variant.

PubMed

Prajapati, V K; Mitra, Ruchi; Vinayak, K M

2017-01-01

Caries in second molar is common and prophylactic removal of the impacted teeth may be considered appropriate. Caries detection and restoration can be difficult and a restored second molar can undergo recurrent caries if the third molar is not removed prophylactically. In this study, the clinical findings related to impaction and its association with angular position and depth of impacted third molar were evaluated. A retrospective descriptive study was carried out among the patients visiting the outpatient, department of Dentistry, RIMS, Ranchi. The clinical examination, periapical radiographs and Pre-op OPG were taken. Teeth positions were analyzed by Pell and Gregory and Winter classification. The angulation and depth of mandibular third molar impaction and caries in the second molar with the eruption status of the mandibular third molar was determined. A total of 200 patients were included in the study between age group 17-45 years. Majority of the Patients reported to the hospital with complaints of decayed tooth (66%) and pain (59%). The most common third molar impaction was mesioangular followed by distoangular. A statistically highly significant difference ( P = 0.001) was obtained with the presence of caries in second molar adjacent to mesioangular third molar in class I and level B. According to this study, pattern of mandibular third molar impaction is in association to caries in mandibular second molar. More future studies are needed. In addition, the results of the present study can be used to screen and inform the patients about the possibility of caries in relation to third molar mandibular impaction.

Effect of dental wear, stabilization appliance and anterior tooth reconstruction on mandibular movements during speech.

PubMed

Serrano, Priscila de Oliveira; Faot, Fernanda; Del Bel Cury, Altair Antoninha; Rodrigues Garcia, Renata Cunha Matheus

2008-01-01

This study described changes in mandibular movements during pronunciation of /m/ and /s/ sounds in Portuguese, in patients presenting dental wear before and after appliance insertion and tooth reconstruction. Subjects were divided into a control group of dentate patients and an experimental group of patients with incisal tooth wear due to bruxism. A magnetic jaw tracking device measured the jaw opening, and translations to left and right sides of the mandible during pronunciation of phonemes. Evaluations were carried out 1 week and immediately before appliance insertion; 24 h, 7, 30 and 60 days after appliance insertion; and 1 week and 1 month after tooth reconstruction. Data were submitted to two-way ANOVA, Mann-Whitney and Friedman tests (p<0.05). Jaw opening was different (p<0.05) for both sounds in all periods. The anteroposterior amplitude for /s/ showed differences immediately before and 1 month after appliance insertion (p<0.05). Lateral amplitude for the right side showed differences between groups after appliance insertion for /s/, and 1 and 2 months after appliance insertion for the /m/ (p<0.05). Volunteers with anterior tooth wear had a wider opening movement, and the movements during speech of /m/ and /s/ sounds were not changed after appliance insertion and reconstruction of teeth.

The use of resorbable plates in association with dental arch stabilization in the treatment of mandibular fractures in children.

PubMed

Li, Zhi; David, Ongodia; Li, Zu-Bing

2014-07-01

The purpose of this study was to investigate the effect of resorbable plate fixation in association with dental arch stabilization in the treatment of displaced mandibular fractures in children. Thirteen children (5 girls and 8 boys, age range 2 years 5 months to 12 years 2 months) with displaced mandibular fractures were included in this case series. Open reduction by intraoral approach was performed on these patients, and the fractures were fixed using resorbable plates and monocortical screws placed at the lower border of the mandible. At the same time, an arch bar or orthodontic wire splint was anchored using stainless steel wires or resin on the teeth to stabilize the whole mandibular dental arch. Postoperatively, follow-up was undertaken to evaluate the fracture healing, mandible movement, and mandible growth. Postoperatively, all patients achieved uneventful healing; premorbid occlusion restoration and wound healing were achieved, along with unimpaired function and normal growth and development of the mandible. Complications such as damage to tooth buds, infection, malunion, and nonunion were not encountered in these patients. Resorbable plates use in association with dental arch stabilization can provide good stabilization for mandibular fractures and is a promising approach for the treatment of displaced mandibular fractures in children. Copyright © 2013 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

A finite element analysis of the optimal bending angles in a running loop for mesial translation of a mandibular molar using indirect skeletal anchorage.

PubMed

Kim, M-J; Park, J H; Kojima, Y; Tai, K; Chae, J-M

2018-02-01

To estimate the optimal bending angles in the running loop for mesial translation of a mandibular second molar using indirect skeletal anchorage and to clarify the mechanics of tipping and rotating the molar. A three-dimensional finite element model was developed for predicting tooth movement, and a mechanical model based on the beam theory was constructed for clarifying the force systems. When using a running loop without bends, the molar tipped mesially 14.4° and lingually 0.6°, rotated counterclockwise 4.1°, and the incisors retracted 0.02 mm and intruded 0.05 mm. These angles were about the same as those estimated by the beam theory. When the amount of tip back and toe-in angles was 11.0°, mesial translation of the molar was achieved, and incisors retracted 0.10 mm and intruded 0.30 mm. Mesial translation of a mandibular second molar without any significant movement of anterior teeth was achieved during protraction by controlling the tip back and toe-in angles and enhancing anterior anchorage with the combined use of a running loop and indirect skeletal anchorage. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Camouflage of moderate Class III malocclusions with extraction of lower second molars and mandibular cervical headgear.

PubMed

Mora, Diego Rey; Oberti, Giovanni; Ealo, Martha; Baccetti, Tiziano

2007-01-01

Orthodontic camouflage in patients with slight or moderate skeletal Class III malocclusions, can be obtained through different treatment alternatives. The purpose of this paper is to present a treatment that has not been described in the literature and which consists of the extraction of lower second molars and distal movement of the posterior segments by means of mandibular cervical headgear (MCH) and fixed appliances as a camouflage alternative. The force applied by the MCH was 250 gr per side (14hr/day). The total treatment time was 1 1/2 years. the extraction of lower second molars along with the use of mandibular cervical headgear is a good treatment alternative for camouflage in moderate Class III patients in order to obtain good occlusal relationships without affecting facial esthetics or producing marked dental compensations.

Cephalometric superimpositions.

PubMed

Gu, Yan; McNamara, James A

2008-11-01

To test the hypothesis that there is no difference between the information produced by superimposition of serial lateral headfilms on anatomical structures and that produced by superimposition on metallic implants according to the protocols of Björk. Serial cephalograms of 10 untreated subjects who had tantalum implants placed in the maxilla and mandible during childhood were analyzed. Headfilms taken at six consecutive stages of cervical vertebral maturation (CS1-CS6) for six female and four male subjects were used. Tracings were superimposed according to the methods of superimpositions advocated by the American Board of Orthodontics (ABO). In addition, superimpositions along the inferior border of the mandible were performed. Finally, superimpositions of serial tracings on stable intraosseous implants were made to determine the actual growth and remodeling patterns of the maxilla and mandible. The ABO maxillary superimposition method underestimates the vertical displacement and overestimates the forward movement of maxillary landmarks. Superimposing on the internal cortical outline of the symphysis and the inferior alveolar nerve canals generally approximates the mandibular superimposition on implants, although the lower anterior border of the symphysis may be a preferable area of superimposition. Superimposition on the lower border of the mandible does not reflect accurately the actual pattern of growth and remodeling of the mandible. When analyzing serial headfilms, erroneous information concerning patterns of bone growth and remodeling can be obtained if convenient, but biologically incorrect superimposition protocols are used. In addition, tooth movements measured can be distorted significantly depending on the method of superimposition.

Root Canal Treatment of Mandibular Second Premolar with Three Separate Roots and Canals Using Spiral Computed Tomographic

PubMed Central

Hariharavel, V. P.; Kumar, A. Ashok; Ganesh, C.; Aravindhan, R.

2014-01-01

Anatomic and internal morphology of a root canal system is more complex and differs for each individual tooth of which mandibular premolars have earned the reputation for having aberrant anatomy. The occurrence of three canals with three separate foramina in mandibular second premolars is very rare. A wider knowledge on both clinical and radiological anatomy especially spiral computed tomographic is absolutely essential for the success of endodontic treatment. These teeth may require skillful and special root canal special shaping and obturating techniques. This paper reports an unusual case of a mandibular second premolar with atypical canal pattern that was successfully treated endodontically. PMID:25101187

Sexual dimorphism of the internal mandibular chamber in Fayum Pliohyracidae (Mammalia)

USGS Publications Warehouse

de Blieux, D.D.; Baumrind, M.R.; Simons, E.L.; Chatrath, P.S.; Meyer, G.E.; Attia, Y.S.

2006-01-01

An internal mandibular fenestra and chamber are found in many fossil hyracoids. The internal mandibular fenestra is located on the lingual surface of the mandibular corpus and opens into a chamber within the mandible. The mandibular chamber is maximally developed in late Eocene Thyrohyrax meyeri and early Oligocene Thyrohyrax domorictus from the Fayum Province of Egypt. The function of this chamber is unknown as it is not found in extant hyraxes, nor is it known to occur in any other mammal. In Thyrohyrax, this feature appears to be sexually dimorphic because it is confined to roughly one half of the specimens that otherwise cannot be separated by dental characteristics or measurements. It has been suggested that the chamber is found in females based on the presumed distribution of this character in other fossil hyracoids. Fossils from Fayum Quarry L-41, preserving the sexually dimorphic anterior dentition, show that, in Thyrohyrax meyeri and Thyrohyrax domorictus, the internal mandibular chamber is found in males. In Thyrohyrax litholagus, an internal mandibular fenestra and inflated mandibular chamber occurs in males whereas females show the variable presence of an internal mandibular fossa or fenestra but lack an expanded chamber. Other genera show differing patterns of sexual variation in which some Fayum hyracoids have an internal mandibular fenestra in both sexes but with the greatest development of the mandibular chamber occurring in males. We review functions proposed for the internal mandibular chamber and suggest that it housed a laryngeal air sac that may have had a vocal function by acting as a resonating chamber. ?? 2006 by the Society of Vertebrate Paleontology.

Treatment of chronic mandibular dislocations by eminectomy: follow-up of 10 cases and literature review.

PubMed

Vasconcelos, Belmiro-Cavalcanti do Egito; Porto, Gabriela-Granja; Neto, José-Pacheco-Martins-Ribeiro; Vasconcelos, César-Freire de Melo

2009-11-01

Temporomandibular joint (TMJ) dislocation is defined as an excessive forward movement of the condyle beyond the articular eminence, with complete separation of the articular surfaces and fixation in that position. To report ten cases treated by eminectomy for chronic mandibular dislocations, to evaluate the results of these surgeries and make a critical review of the literature. The sample was obtained from the records of the Department of Oral and Maxillofacial Surgery, University of Pernambuco and comprises cases submitted to chronic mandibular dislocation treatment by eminectomy between 2002 and 2007. Pre- and postoperative assessment included a thorough history and physical examination to determine the maximal mouth opening, presence of pain and sounds, frequency of luxations, recurrence rate and presence of facial nerve paralysis. The mean maximal mouth opening in the preoperative period was 48.4 +/- 8.5 mm and in the postoperative period it was 41.3 +/- 5.0 mm. No facial nerve paralysis or recurrence was observed. The treatment of chronic mandibular dislocations by eminectomy was shown to be efficient in relationship to the postoperative maximal mouth opening, recurrence and articular function.

[Stress analysis of the mandible by 3D FEA in normal human being under three loading conditions].

PubMed

Sun, Jian; Zhang, Fu-qiang; Wang, Dong-wei; Yu, Jia; Wang, Cheng-tao

2004-02-01

The condition and character of stress distribution in the mandibular in normal human being during centric, protrusive, laterotrusive occlusion were analysed. The three-dimensional finite element model of the mandibular was developed by helica CT scanning and CAD/CAM software, and three-dimensional finite element stress analysis was done by ANSYS software. Three-dimensional finite element model of the mandibular was generated. Under these three occlusal conditions, the stress of various regions in the mandible were distributed unequally, and the stress feature was different;while the stress of corresponding region in bilateral mandibular was in symmetric distribution. The stress value of condyle neck, the posterior surface of coronoid process and mandibular angle were high. The material properties of mandible were closely correlated to the value of stress. Stress distribution were similar according to the three different loading patterns, but had different effects on TMJ joint. The concentrated areas of stress were in the condyle neck, the posterior surface of coronoid process and mandibular angle.

Craniofacial morphometric analysis of mandibular prognathism.

PubMed

Chang, H P; Liu, P H; Yang, Y H; Lin, H C; Chang, C H

2006-03-01

The purpose of this study was to provide more information about the morphological characteristics of the craniofacial complex in mandibular prognathism. Forty young adult males having mandibular prognathism were compared with 40 having normal occlusion. This was conducted to carry out geometric morphometric assessments to localize alterations, using Procrustes analysis and thin-plate spline analysis, in addition to conventional cephalometric techniques. Procrustes analysis indicated that the mean craniofacial, midfacial and mandibular morphology was significantly different in prognathic subjects compared with normal controls. This finding was corroborated by the multivariate Hotelling T(2)-test of cephalometric variables. Mandibular prognathism demonstrated a shorter and slightly retropositioned maxilla, a greater total length and anterior positioning of the mandible. Thin-plate spline analysis revealed a developmental diminution of the palatomaxillary region anteroposteriorly and a developmental elongation of the mandible anteroposteriorly, leading to the appearance of a prognathic mandibular profile. In conclusion, thin-plate spline analysis seems to provide a valuable supplement for conventional cephalometric analysis because the complex patterns of craniofacial shape change are visualized suggestive by means of grid deformations.

Pattern of mandibular third molar impaction and its association to caries in mandibular second molar: A clinical variant

PubMed Central

Prajapati, V. K.; Mitra, Ruchi; Vinayak, K. M.

2017-01-01

Background: Caries in second molar is common and prophylactic removal of the impacted teeth may be considered appropriate. Caries detection and restoration can be difficult and a restored second molar can undergo recurrent caries if the third molar is not removed prophylactically. In this study, the clinical findings related to impaction and its association with angular position and depth of impacted third molar were evaluated. Materials and Methods: A retrospective descriptive study was carried out among the patients visiting the outpatient, department of Dentistry, RIMS, Ranchi. The clinical examination, periapical radiographs and Pre-op OPG were taken. Teeth positions were analyzed by Pell and Gregory and Winter classification. The angulation and depth of mandibular third molar impaction and caries in the second molar with the eruption status of the mandibular third molar was determined. Results: A total of 200 patients were included in the study between age group 17-45 years. Majority of the Patients reported to the hospital with complaints of decayed tooth (66%) and pain (59%). The most common third molar impaction was mesioangular followed by distoangular. A statistically highly significant difference (P = 0.001) was obtained with the presence of caries in second molar adjacent to mesioangular third molar in class I and level B. Conclusion: According to this study, pattern of mandibular third molar impaction is in association to caries in mandibular second molar. More future studies are needed. In addition, the results of the present study can be used to screen and inform the patients about the possibility of caries in relation to third molar mandibular impaction. PMID:28584538

Three-dimensional computer-assisted study model analysis of long-term oral-appliance wear. Part 1: Methodology.

PubMed

Chen, Hui; Lowe, Alan A; de Almeida, Fernanda Riberiro; Wong, Mary; Fleetham, John A; Wang, Bangkang

2008-09-01

The aim of this study was to test a 3-dimensional (3D) computer-assisted dental model analysis system that uses selected landmarks to describe tooth movement during treatment with an oral appliance. Dental casts of 70 patients diagnosed with obstructive sleep apnea and treated with oral appliances for a mean time of 7 years 4 months were evaluated with a 3D digitizer (MicroScribe-3DX, Immersion, San Jose, Calif) compatible with the Rhinoceros modeling program (version 3.0 SR3c, Robert McNeel & Associates, Seattle, Wash). A total of 86 landmarks on each model were digitized, and 156 variables were calculated as either the linear distance between points or the distance from points to reference planes. Four study models for each patient (maxillary baseline, mandibular baseline, maxillary follow-up, and mandibular follow-up) were superimposed on 2 sets of reference points: 3 points on the palatal rugae for maxillary model superimposition, and 3 occlusal contact points for the same set of maxillary and mandibular model superimpositions. The patients were divided into 3 evaluation groups by 5 orthodontists based on the changes between baseline and follow-up study models. Digital dental measurements could be analyzed, including arch width, arch length, curve of Spee, overbite, overjet, and the anteroposterior relationship between the maxillary and mandibular arches. A method error within 0.23 mm in 14 selected variables was found for the 3D system. The statistical differences in the 3 evaluation groups verified the division criteria determined by the orthodontists. The system provides a method to record 3D measurements of study models that permits computer visualization of tooth position and movement from various perspectives.

Mandibular anterior crowding: normal or pathological?

PubMed

Consolaro, Alberto; Cardoso, Mauricio de Almeida

2018-01-01

The teeth become very close to each other when they are crowded, but their structures remain individualized and, in this situation, the role of the epithelial rests of Malassez is fundamental to release the EGF. The concept of tensegrity is fundamental to understand the responses of tissues submitted to forces in body movements, including teeth and their stability in this process. The factors of tooth position stability in the arch - or dental tensegrity - should be considered when one plans and perform an orthodontic treatment. The direct causes of the mandibular anterior crowding are decisive to decide about the correct retainer indication: Should they be applied and indicated throughout life? Should they really be permanently used for lifetime? These aspects of the mandibular anterior crowding and their implication at the orthodontic practice will be discussed here to induct reflections and insights for new researches, as well as advances in knowledge and technology on this subject.

Multidisciplinary approach to an asymmetric traumatic occlusion: a case report.

PubMed

Pinho, T; Coutinho-Alves, C; Neves, M

2013-01-01

The case of a 47-year-old female patient with an asymmetric traumatic occlusion, great alveolar destruction in the mandibular left central incisor, gingival recession with attachment loss and lack o fkeratinized tissue more accentuated in the crossbite teeth is described. This situation was caused by the traumatic position of the teeth, aggravated by a forced asymmetric anterior position of the mandible and aggravated by mandibular movements. After the extraction of the left central mandibular incisor, keratinized tissue reconstruction and alveolar bone regeneration were performed to obtain enough bone to move the adjacent teeth in this direction and allow the correct placement of an implant at the end of orthodontic treatment. The orthodontic treatment achieved general stable occlusal contacts and esthetic results that were finalized with a definitive prosthetic treatment. This interdisciplinary management was important to solve in the present case the seriously compromised function and esthetics that would never be achieved without this combination.

Prosthodontic management of segmental mandibulectomy patient with guidance appliance and overlay denture.

PubMed

Aruna, U; Thulasingam, C

2013-12-01

Patients who undergo segmental or hemi-mandibulectomy suffer from various postoperative problems in esthetics and function. The solution to such problem is providing a mandibular guidance appliance to correct mandibular deviation to resected side due to loss of muscle action on the affected side. This article describes the treatment of a female patient who underwent segmental mandibulectomy on right side secondary to adenoid cystic carcinoma of the base of tongue. An acrylic guidance appliance was constructed to help control the mandibular deviation and co-ordinate masticatory movements. The prosthesis was worn continuously by the patient for 1 month which corrected the occlusion on the left side. To compensate for the open-bite caused due to rotation of mandible following partial mandibulectomy, an overlay removable partial denture was given. The patient was satisfied with the improvement in esthetics and mastication.

[Anatomical rationale for lingual nerve injury prevention during mandibular block].

PubMed

Semkin, V A; Dydikin, S S; Kuzin, A V; Sogacheva, V V

2015-01-01

The topographic and anatomical study of lingual nerve structural features was done. It was revealed that during mandibular anesthesia possible lingual nerve injury can occur if puncture needle is lower than 1 cm. of molars occlusal surface level. The position of the lingual nerve varies withmandible movements. At the maximum open mouth lingual nerve is not mobile and is pressed against the inner surface of the mandibular ramus by the medial pterygoid muscle and the temporal muscle tendon. When closing the mouth to 1.25±0.2 cmfrom the physiological maximum, lingual nerve is displaced posteriorly from the internal oblique line of the mandible and gets mobile. On the basis of topographic and anatomic features of the lingual nervestructure the authors recommend the re-do of inferior alveolar nerve block, a semi-closed mouth position or the use the "high block techniques" (Torus anesthesia, Gow-Gates, Vazirani-Akinozi).

[Exploring a new method for superimposition of pre-treatment and post-treatment mandibular digital dental casts in adults].

PubMed

Dai, F F; Liu, Y; Xu, T M; Chen, G

2018-04-18

To explore a cone beam computed tomography (CBCT)-independent method for mandibular digital dental cast superimposition to evaluate three-dimensional (3D) mandibular tooth movement after orthodontic treatment in adults, and to evaluate the accuracy of this method. Fifteen post-extraction orthodontic treatment adults from the Department of Orthodontics, Peking University School and Hospital of Stomatology were included. All the patients had four first premolars extracted, and were treated with straight wire appliance. The pre- and post-treatment plaster dental casts and craniofacial CBCT scans were obtained. The plaster dental casts were transferred to digital dental casts by 3D laser scanning, and lateral cephalograms were created from the craniofacial CBCT scans by orthogonal projection. The lateral cephalogram-based mandibular digital dental cast superimposition was achieved by sequential maxillary dental cast superimposition registered on the palatal stable region, occlusal transfer, and adjustment of mandibular rotation and translation obtained from lateral cephalogram superimposition. The accuracy of the lateral cephalogram-based mandibular digital dental cast superimposition method was evaluated with the CBCT-based mandibular digital dental cast superimposition method as the standard reference. After mandibular digital dental cast superimposition using both methods, 3D coordinate system was established, and 3D displacements of the lower bilateral first molars, canines and central incisors were measured. Differences between the two superimposition methods in tooth displacement measurements were assessed using the paired t-test with the level of statistical significance set at P<0.05. No significant differences were found between the lateral cephalogram-based and CBCT-based mandibular digital dental cast superimposition methods in 3D displacements of the lower first molars, and sagittal and vertical displacements of the canines and central incisors; transverse displacements of the canines and central incisors differed by (0.3±0.5) mm with statistical significance. The lateral cephalogram-based mandibular digital dental cast superimposition method has the similar accuracy as the CBCT-based mandibular digital dental cast superimposition method in 3D evaluation of mandibular orthodontic tooth displacement, except for minor differences for the transverse displacements of anterior teeth. This method is applicable to adult patients with conventional orthodontic treatment records, especially the previous precious orthodontic data in the absence of CBCT scans.

Morphological assessment of the mandibular canal trajectory in edentate subjects.

PubMed

Nimigean, Victor; Sîrbu, Valentin Daniel; Nimigean, Vanda Roxana; Bădiţă, Daniela Gabriela; Poll, Alexandru; Moraru, Simona Andreea; Păun, Diana Loreta

2018-01-01

The mandibular canal and its content represent the vital structure, which can complicate dentoalveolar surgical procedures in the posterior region of the mandible. The purpose of the present study was to determine the path the mandibular canal takes in relation to the horizontal and the vertical anatomical reference planes in edentate subjects, in order to minimize the risk of affecting its neurovascular content during various oral surgery procedures. Morphometric evaluations were performed on 12 dried fully edentulous human mandibles and on cone-beam computed tomography (CBCT) cross-sectional images of the mandible, from 20 patients with either partial or complete edentulism. Both methods were utilized, in three target areas (corresponding to the second premolar, to the first molar and to the second molar regions), in order to measure the distance between the mandibular canal and the following reference points: (i) the lateral (buccal) surface of the mandible (MC-BS distance); (ii) the medial (lingual) surface of the mandible (MC-LS distance); (iii) the alveolar surface of the mandible (MC-AS distance). The results were statistically processed in Stata MP/13 software package using analysis of variance (ANOVA) test. The mandibular canal crossed the trabecular bone from the posterior towards the anterior, and from the lingual towards the buccal, reaching the premolar region, distal to the mental foramen, where it was located in the centre of the trabecular bone, main topographic pattern encountered in 27 (84.37%) of the cases. In five (15.63%) of the cases, in the premolar region, the mandibular canal was located near the buccal cortical plate. The mandibular canal descended from the second molar region towards the premolar region, main topographic pattern found in 28 (87.5%) of the cases. In four (12.5%) cases, the mandibular canal had a descending trajectory in the molar regions and it took a slightly ascending course in the premolar region. According to the results, the second molar region represents the highest risk area in the accidental injury to the content of the mandibular canal, during various oral surgery procedures.

Superimposition of 3D digital models: A case report.

PubMed

José Viñas, María; Pie de Hierro, Verónica; M Ustrell-Torrent, Josep

2018-06-01

Superimposition of digital models may be performed to assess tooth movement in three dimensions. Detailed analysis of changes in tooth position after treatment may be achieved by this method. This article describes the method of superimposing digital models with a clinical case. It emphasizes the difficult procedure of superimposing 3D models in the lower arch. A methodology for superimposing mandibular models acquired with a structured light 3D scanner is discussed. Superimposition of digital models is useful to analyse tooth movement in the three planes of space, presenting advantages over the method of cephalogram superimposition. It seems feasible to superimpose digital models in the lower arch in patients without growth by using a coordinate system based on the palatal rugae and occlusion. The described method aims to advance the difficult procedure of superimposing digital models in the mandibular arch, but further research is nonetheless required in this field. Copyright © 2018 CEO. Published by Elsevier Masson SAS. All rights reserved.

Effects of first premolar extraction on maxillary and mandibular third molar angulation after orthodontic therapy

PubMed Central

Gohilot, Avinash; Pradhan, Tejashri; Keluskar, Kanhoba Mahabaleshwar

2012-01-01

Background/Aims To compare the change in the angulation of developing mandibular third molar in both first premolar extraction and non-extraction cases and to determine whether premolar extraction results in a more mesial movement of the mandibular buccal segment and causes favorable rotational changes in the mandibular third molar tilt, which can enhance later eruption of the third molars. Materials and methods Pretreatment (T1) and post treatment (T2) panoramic radiographs were taken of 25 subjects (age 14–19 years) who had been treated by the extraction of all the first premolars and 25 subjects who had been treated with non-extraction. The horizontal reference plane was used to measure and compare the changes in the angles of the developing mandibular third molars. Results The mean uprighting of the maxillary third molars seen in the extraction group was 4 ± 9° on the left side and −17 ± 13° on the right side following treatment (T2 _ T1). For the non-extraction group the mean difference was −16 ± 12° on the left side and 2 ± 13° on the right side. There was a statistically significant difference between the groups (P _ 0.021 on the right side and P _ 0.041 on the left side). Mandibular 3rd molars in extraction group showed no statistical significant change in the angulation. Conclusion Premolar extractions had a positive influence on the developing maxillary third molar angulations both on right and left. Mandibular 3rd molar have shown change in the angulation but not statistically significant. Non-extraction therapy did not have any adverse effect. PMID:25737843

Effects of first premolar extraction on maxillary and mandibular third molar angulation after orthodontic therapy.

PubMed

Gohilot, Avinash; Pradhan, Tejashri; Keluskar, Kanhoba Mahabaleshwar

2012-01-01

To compare the change in the angulation of developing mandibular third molar in both first premolar extraction and non-extraction cases and to determine whether premolar extraction results in a more mesial movement of the mandibular buccal segment and causes favorable rotational changes in the mandibular third molar tilt, which can enhance later eruption of the third molars. Pretreatment (T1) and post treatment (T2) panoramic radiographs were taken of 25 subjects (age 14-19 years) who had been treated by the extraction of all the first premolars and 25 subjects who had been treated with non-extraction. The horizontal reference plane was used to measure and compare the changes in the angles of the developing mandibular third molars. The mean uprighting of the maxillary third molars seen in the extraction group was 4 ± 9° on the left side and -17 ± 13° on the right side following treatment (T2 _ T1). For the non-extraction group the mean difference was -16 ± 12° on the left side and 2 ± 13° on the right side. There was a statistically significant difference between the groups (P _ 0.021 on the right side and P _ 0.041 on the left side). Mandibular 3rd molars in extraction group showed no statistical significant change in the angulation. Premolar extractions had a positive influence on the developing maxillary third molar angulations both on right and left. Mandibular 3rd molar have shown change in the angulation but not statistically significant. Non-extraction therapy did not have any adverse effect.

Thin-plate spline graphical analysis of the mandible in mandibular prognathism.

PubMed

Chang, Hsin-Fu; Chang, Hong-Po; Liu, Pao-Hsin; Chang, Chih-Han

2002-11-01

The chin cup has been used to treat skeletal mandibular prognathism in growing patients for 200 years. The pull on the orthopedic-force chin cup is oriented along a line from the mandibular symphysis to the mandibular condyle. Various levels of success have been reported with this restraining device. The vertical chin cup produces strong vertical compression stress on the maxillary molar regions when the direction of traction is 20 degrees more vertical than the chin-condyle line. This treatment strategy may prevent relapse due to counter-clockwise rotation of the mandible. In this report, we describe a new strategy for using chin-cup therapy involving thin-plate spline (TPS) analysis of lateral cephalometric roentgenograms to visualize transformation of the mandible. The actual sites of mandibular skeletal change are not detectable with conventional cephalometric analysis. A case of mandibular prognathism treated with a chin cup and a case of dental Class III malocclusion without orthodontic treatment are described. The case analysis illustrates that specific patterns of mandibular transformation are associated with Class III malocclusion with or without orthopedic therapy, and that visualization of these deformations is feasible using TPS graphical analysis.

A Biomechanical Comparison of Three 1.5-mm Plate and Screw Configurations and a Single 2.0-mm Plate for Internal Fixation of a Mandibular Condylar Fracture

PubMed Central

Aquilina, Peter; Parr, William C.H.; Chamoli, Uphar; Wroe, Stephen; Clausen, Philip

2014-01-01

The most stable pattern of internal fixation for mandibular condyle fractures is an area of ongoing discussion. This study investigates the stability of three patterns of plate fixation using readily available, commercially pure titanium implants. Finite element models of a simulated mandibular condyle fracture were constructed. The completed models were heterogeneous in bone material properties, contained approximately 1.2 million elements and incorporated simulated jaw adducting musculature. Models were run assuming linear elasticity and isotropic material properties for bone. No human subjects were involved in this investigation. The stability of the simulated condylar fracture reduced with the different implant configurations, and the von Mises stresses of a 1.5-mm X-shaped plate, a 1.5-mm rectangular plate, and a 1.5-mm square plate (all Synthes (Synthes GmbH, Zuchwil, Switzerland) were compared. The 1.5-mm X plate was the most stable of the three 1.5-mm profile plate configurations examined and had comparable mechanical performance to a single 2.0-mm straight four-hole plate. This study does not support the use of rectangular or square plate patterns in the open reduction and internal fixation of mandibular condyle fractures. It does provide some support for the use of a 1.5-mm X plate to reduce condylar fractures in selected clinical cases. PMID:25136411

Graphic tracings of condylar paths and measurements of condylar angles.

PubMed

el-Gheriani, A S; Winstanley, R B

1989-01-01

A study was carried out to determine the accuracy of different methods of measuring condylar inclination from graphical recordings of condylar paths. Thirty subjects made protrusive mandibular movements while condylar inclination was recorded on a graph paper card. A mandibular facebow and intraoral central bearing plate facilitated the procedure. The first method proved to be too variable to be of value in measuring condylar angles. The spline curve fitting technique was shown to be accurate, but its use clinically may prove complex. The mathematical method was more practical and overcame the variability of the tangent method. Other conclusions regarding condylar inclination are outlined.

Nonsurgical Management of Pediatric Temporomandibular Joint Dysfunction.

PubMed

Scrivani, Steven John; Khawaja, Shehryar Nasir; Bavia, Paula Furlan

2018-02-01

Temporomandibular disorders (TMD) are a subgroup of craniofacial pain problems involving the temporomandibular joint (TMJ), masticatory muscles, and associated head and neck musculoskeletal structures. These disorders are subclassified into TMJ articular disorders and masticatory muscle disorders. Patients with TMD most commonly present with pain, restricted or asymmetric mandibular motion, and TMJ sounds during mandibular movements. The prevalence tends to increase with age. Management of TMJ articular disorders consists of a combination of patient education, home-care plan, biobehavioral therapy, physical therapy, orthotic jaw appliance therapy, pharmacotherapy, and/or surgery. The goal is to increase function, reduce pain, and improve quality of life. Copyright © 2017 Elsevier Inc. All rights reserved.

Maxillary and Mandibular First Premolars Showing Three-Cusp Pattern: An Unusual Presentation

PubMed Central

Kotrashetti, Vijayalakshmi; Nayak, Aarati; Patil, Viraj; Kulkarni, Mayuri; Somannavar, Pradeep

2013-01-01

Dental anatomy is the study of morphology of various teeth in human dentitions. The application of dental anatomy in clinical practice is important, and dentist should have a thorough knowledge regarding the morphology of the teeth. At times as a result of genetic variation, environmental factors, diet of an individual and race, variations in the morphology of the teeth can be observed. These variations have been extensively studied by the researcher in the field of anthropology to define a particular race. The most commonly observed changes include peg-shaped laterals, shovel-shaped incisors, and extra cusp on molar. Common variations documented with regard to maxillary and mandibular first premolars are the variation in the number of roots. But the variations with respect to crown morphology are few. We report a first documented unusual presentation of maxillary and mandibular first premolars with three-cusps pattern in a female patient. PMID:23476817

Morphologic and functional implications of the surgical-orthodontic management of mandibular prognathism: a comprehensive review.

PubMed

Athanasiou, A E

1993-05-01

The aim of this review is to present the various morphologic and functional implications of the surgical-orthodontic management of mandibular prognathism, thus providing a more complete determination of the efficacy of this modality of treatment. Major conclusions that can be drawn from the bibliography indicate that: (1) After treatment considerable improvement takes place on the soft tissue and dentoskeletal profile, occlusal tooth contacts, and temporomandibular joint function and and pain; (2) Surgical management of mandibular prognathism can be associated with decreased maximum interincisal opening; (3) Although immediately after surgery there is a tendency for the condyles to be distracted downward and anteriorly from their preoperative position, in long-term postsurgery the condyles, on the average, regain their initial position; (4) Compensatory alterations in the pharyngeal, suprahyoid, and infrahyoid muscular regions take place postoperatively; (5) Skeletal changes after mandibular setback to correct mandibular prognathism occur frequently, but their magnitude and patterns exhibit variation and are not necessarily detrimental; and (6) Fulfillment of expectations toward surgical-orthodontic management of mandibular prognathism was reported to be frequent.

Orthodontic Extraction of High-Risk Impacted Mandibular Third Molars in Close Proximity to the Mandibular Canal: A Systematic Review.

PubMed

Kalantar Motamedi, Mahmood Reza; Heidarpour, Majid; Siadat, Sara; Kalantar Motamedi, Alimohammad; Bahreman, Ali Akbar

2015-09-01

Extraction of mandibular third molars (M3s) in close proximity to the mandibular canal has some inherent risks to adjacent structures, such as neurologic damage to teeth, bone defects distal to the mandibular second molar (M2), or pathologic fractures in association with enlarged dentigerous cysts. The procedure for extrusion and subsequent extraction of high-risk M3s is called orthodontic extraction. This is a systematic review of the available approaches for orthodontic extraction of impacted mandibular M3s in close proximity to the mandibular canal and their outcomes. The PubMed, Scopus, Cochrane Central Register of Controlled Trials (CENTRAL), DOAJ, Google Scholar, OpenGrey, Iranian Science Information Database (SID), Iranmedex, and Irandoc databases were searched using specific keywords up to June 2, 2014. Studies were evaluated based on predetermined eligibility criteria, treatment approaches, and their outcomes. Thirteen articles met the inclusion criteria. A total of 123 impacted teeth were extracted by orthodontic extraction and 2 cases were complicated by transient paresthesia. Three types of biomechanical approaches were used: 1) using the posterior maxillary region as the anchor for orthodontic extrusion of lower M3s, 2) simple cantilever springs attached to the M3 buttonhole, and 3) cantilever springs tied to a bonded orthodontic bracket on the M3 plus multiple-loop spring wire for distal movement of the M3. Osteo-periodontal status of M2s also improved uneventfully. Despite the drawbacks of orthodontic extraction, removal of deeply impacted M3s using the described techniques is safe with regard to mandibular nerve injury and neurologic damage. Orthodontic extraction is recommended for extraction of impacted M3s that present a high risk of postoperative osteo-periodontal defects on the distal surface of the adjacent M2 and those associated with dentigerous cysts. Copyright © 2015 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Comparison of periodontal ligament injection and inferior alveolar nerve block in mandibular primary molars pulpotomy: a randomized control trial.

PubMed

Haghgoo, Roza; Taleghani, Ferial

2015-05-01

Inferior alveolar nerve block is a common technique for anesthesia of the primary mandibular molars. A number of disadvantages have been shown to be associated with this technique. Periodontal ligament (PDL) injection could be considered as an alternative to inferior alveolar nerve block. The aim of this study was to evaluate the effectiveness of PDL injection in the anesthesia of primary molar pulpotomy with mandibular block. This study was performed using a sequential double-blind randomized trial design. 80 children aged 3-7 years old who required pulpotomy in symmetrical mandibular primary molars were selected. The teeth of these children were anesthetized with periodontal injection on one side of the mandible and block on the other. Pulpotomy was performed on each patient during the same appointment. Signs of discomfort, including hand and body tension and eye movement, the verbal complaint and crying (SEM scale), were evaluated by a dental assistant who was blinded to the treatment allocation of the patients. Finally, the data were analyzed using the exact Fisher test and Pearson Chi-squared exact test. Success rate was 88/75 and 91/25 in the PDL injection and nerve block groups, respectively. There was no statistically significant difference between the two techniques (P = 0.250). Results showed that PDL injection can be used as an alternative to nerve block in pulpotomy of the mandibular primary molars.

Surgical management of pediatric mandibular trauma.

PubMed

Aldelaimi, Tahrir N; Khalil, Afrah A

2013-05-01

Surgical treatment of pediatric maxillofacial region is a complex and challenging task to maxillofacial surgeons. Incorrect and inappropriate treatment of trauma will end with a secondary deformity that is very difficult to correct. Twenty-eight children with mandibular trauma were seen at the maxillofacial surgery department of Ramadi Teaching Hospital during the period from July 2009 to June 2012. Age, sex, etiology, associated injuries, pattern of fractures, and treatments were reviewed. Road traffic accident was the most common cause for pediatric mandibular trauma. Significant advances have been made in the management of these injuries, decreasing the incidence of secondary deformities.

Temporo-mandibular joint condylectomy and its effect over occlusion in cats: cadaveric study.

PubMed

El-Warrak, A O; Ferrer, G A; Lanthier, T; Loureiro Silva, B; El-Warrak, L O

2011-03-01

To determine the effect of unilateral condylectomy on dental occlusion in cats. Twelve feline cadaver heads were randomly submitted to either a right or left unilateral condylectomy of the temporo-mandibular joint. The distance between the mandibular and maxillary canine tooth was measured before (B0) and after the unilateral condylectomy (P0). A right or left latero--lateral standardised force (4 N) was applied to the mandibular mentus area before and after the surgical procedure. These measurements were analysed with a linear model for repeated measures. The comparative analysis between pre- and postsurgical values indicated no significant variation in teeth displacement following condylectomy between B0 and P0 measurements. Statistically significant differences were detected after either left or right condylectomy with respect to all measurements after application of the standardised forces. Occlusion changes are significant when comparing bites before and after surgery. Unilateral condylectomy causes a significant increase in latero-lateral amplitude of jaw movement which might clinically affect feline dental occlusion. Clinical studies are required to determine the effect of unilateral condylectomies on mastication and dental occlusion in feline patients. © 2011 British Small Animal Veterinary Association.

Cap’n’collar differentiates the mandible from the maxilla in the beetle Tribolium castaneum

PubMed Central

2012-01-01

Background The biting mandible of the arthropods is thought to have evolved in the ancestor of the insects, crustaceans and myriapods: the Mandibulata. A unique origin suggests a common set of developmental genes will be required to pattern the mandible in different arthropods. To date we have functional studies on patterning of the mandibular segment of Drosophila melanogaster showing in particular the effects of the gene cap’n’collar (cnc), however, the dipteran head is far from representative of insects or of more distantly related mandibulates; Drosophila does not even possess a mandibular appendage. To study the development of a more representative insect mandible, we chose the red flour beetle Tribolium castaneum and investigated the function of the Tribolium orthologs of cap’n’collar (Tc-cnc) and the Hox gene Deformed (Tc-Dfd). In order to determine the function of Tc-cnc and Tc-Dfd, transcripts were knocked down by maternal RNA interference (RNAi). The effects of gene knockdown were examined in the developing embryos and larvae. The effect of Tc-cnc and Tc-Dfd knockdown on the expression of other genes was determined by using in situ hybridization on Tribolium embryos. Results Our analyses show that Tc-cnc is required for specification of the identity of the mandibular segment of Tribolium and differentiates the mandible from maxillary identity. Loss of Tc-cnc function results in a transformation of the mandible to maxillary identity as well as deletion of the labrum. Tc-Dfd and the Tribolium homolog of proboscipedia (Tc-mxp = maxillopedia), Hox genes that are required to pattern the maxillary appendage, are expressed in a maxilla-like manner in the transformed mandible. Tribolium homologs of paired (Tc-prd) and Distal-less (Tc-Dll) that are expressed in the endites and telopodites of embryonic appendages are also expressed in a maxilla-like manner in the transformed mandible. We also show that Tc-Dfd is required to activate the collar of Tc-cnc expression in the mandibular segment but not the cap expression in the labrum. Tc-Dfd is also required for the activation of Tc-prd in the endites of the mandible and maxillary appendages. Conclusions Tc-cnc is necessary for patterning the mandibular segment of Tribolium. Together, Tc-cnc and Tc-Dfd cooperate to specify mandibular identity, as in Drosophila. Expression patterns of the homologs of cnc and Dfd are conserved in mandibulate arthropods suggesting that the mandible specifying function of cnc is likely to be conserved across the mandibulate arthropods. PMID:23114106

Oral-motor and electromyographic characterization of patients submitted to open a nd closed reductions of mandibular condyle fracture.

PubMed

Silva, Amanda Pagliotto da; Sassi, Fernanda Chiarion; Andrade, Claudia Regina Furquim de

To characterize the oral-motor system of adults with mandibular condyle facture comparing the performance of individuals submitted to open reduction with internal fixation (ORIF) and closed reduction with mandibulomaxillary fixation (CRMMF). Study participants were 26 adults divided into three groups: G1 - eight individuals submitted to ORIF for correction of condyle fracture; G2 - nine individuals submitted to CRMMF for correction of condyle fracture; CG - nine healthy volunteers with no alterations of the orofacial myofunctional system. All participants underwent the same clinical protocol: assessment of the orofacial myofunctional system; evaluation of the mandibular range of motion; and surface electromyography (sEMG) of the masticatory muscles. Results indicated that patients with condyle fractures from both groups presented significant differences compared with those from the control group in terms of mobility of the oral-motor organs, mastication, and deglutition. Regarding the measures obtained for mandibular movements, participants with facial fractures from both groups showed significant differences compared with those from the control group, indicating greater restrictions in mandibular motion. As for the analysis of sEMG results, G1 patients presented more symmetrical masseter activation during the task of maximal voluntary teeth clenching. Patients with mandibular condyle fractures present significant deficits in posture, mobility, and function of the oral-motor system. The type of medical treatment does not influence the results of muscle function during the first six months after fracture reduction. Individuals submitted to ORIF of the condyle fracture present more symmetrical activation of the masseter muscle.

[The effect of first premolar extraction on third molar angulation and eruption space].

PubMed

Xie, Jing-zhong

2009-12-01

To study the influence of the first premolar extraction on the angulation and eruption space of third molar. One hundred and twenty patients cases of Class I malocclusions were divided into 2 groups by age, who were treated with extraction and non-extraction respectively. The following values was measured: angle of cusp line between the second and third molar(alpha angle),impact state and depth, distance from Rickett's Xi to distal cusp of third mandibular molar along the occlusal plane(Xi-LTM), anterior border of ramus to the third mandibular molar(R-LTM), distance from projection of distal contact point of maxillary third molar to intersection of pterygoid vertical on occlusal plane (PTV-UTM). The change between pre- and post-treatment was calculated and analyzed with SPSS10.0 software package. alpha angle, Xi-LTM, R-LTM, R-LTM were tested with independent-sample t test, impact state and depth was tested with Chi-square test. Influence of age on the values was also evaluated. In younger group, changes of mandibular alpha angle and Xi-LTM in extraction group was 7.16 degrees and 3.22mm, but in elder group, these changes was 2.42 degrees and 2.10mm, all values were significantly larger than non-extraction group (P<0.05). Impact state and depth of third mandibular molar improved in extraction group, while there was no significant changes in the maxilla. The third mandibular molar becomes upright and distal movement after first premolar extraction. The possibility of the third mandibular molar impaction is decreased, but the effect on the maxilla is not significant.

[A functional orthodontic magnetic appliance (FOMA) after Vardimon. 1. A three-dimensional analysis of the force system of the attractive magnets].

PubMed

Bourauel, C; Vardimon, A D; Drescher, D; Schmuth, G P

1995-09-01

The functional magnetic system (FMS) is a removable functional appliance which induces mandibular advance by means of mandibular and maxillary magnets in an attracting configuration. The maxillary and mandibular plates are each equipped with 2 cylindrically shaped cobalt-samarium magnets, 4 mm in diameter and 3 mm in height, which are welded into stainless steel housings. The force system of this magnetic configuration was analyzed using the orthodontic measurement and simulation system (OMSS). OMSS simulated the mandibular jaw movements by separating the installed magnets vertically, corresponding to a mouth opening of X = -10 mm, transversally (right excursion, +/left excursion, -) at Y = +/- 10 mm and sagittally (anterior displacement, +/posterior displacement, -) at Z = +/- 10 mm. The resulting 2D and 3D force/displacement diagrams elucidate the outstanding centripetal-spatial orientation characteristics of the functional magnetic appliance in reference to the full overlap brought about by the attraction of the mandibular magnet by the maxillary magnet. The maximum centripetal forces reached a value of approximately FY, max = 0.65 N for the vertical attracting force at full overlap of the mandibular and maxillary magnets (X = 0.55 mm, Y = Z = 0 mm), a value of FY, max = 0.65 N for the medial shearing force at a partial transversal overlap Z = 0, Y = +/- 2 mm and Y = +/- 6 mm), and for the sagittal shearing force a value of FZ, max = 1.2 N at a partial sagittal overlap of the magnets (Y = 0 mm, Z = +/- 2 mm).(ABSTRACT TRUNCATED AT 250 WORDS)

[Molecular cloning, expression of rat Msx-1 and Msx-2 during early embryo genesis and roles for mandibular chondrogenesis].

PubMed

Ishiguro, S

1999-03-01

Quail-chick chimera experiments have shown a contribution of carnial neural crest cells to the craniofacial skeletal elements. Moreover, tissue interactions between epithelial-mesenchymal interaction during early facial process development are required for both skeletal differentiation and morphogenesis. In this study, it was observed that Msx homeobox containing genes expressed in the facial process were important molecules of cartilage morphogenesis. Rat cDNAs were isolated and encoded by Msx-1 and -2, and then the expression patterns using in situ hybridization were investigated during early rat face development. These genes were correlatively expressed in the cranial neural crest forming area (E 9.5 dpc) and the facial process (E 12.5 dpc). Antisence inhibition of Msx genes in the E 12.5 mandibular process exhibited the alteration of their gene expression and cartilage patterns. Antisence inhibition of Msx-1 induced lack of the medial portion of cartilage, and antisence inhibition of Msx-2 enhanced chondrogenesis of mandibular process under the organ culture condition. Thus it was concluded that expression of Msx genes during mandibular process development comprises important signals of chondrogenesis.

Development of a Mandibular Motion Simulator for Total Joint Replacement

PubMed Central

Celebi, Nukhet; Rohner, E. Carlos; Gateno, Jaime; Noble, Philip C.; Ismaily, Sabir K.; Teichgraeber, John F.; Xia, James J.

2015-01-01

Purpose The purpose of this study was to develop a motion simulator capable of recreating and recording the full range of mandibular motions in a cadaveric preparation for an intact temporomandibular joint (TMJ) and after total joint replacement. Material and Methods A human cadaver head was used. Two sets of tracking balls were attached to the forehead and mandible, respectively. Computed tomographic (CT) scan was performed and 3-dimensional CT models of the skull were generated. The cadaver head was then dissected to attach the muscle activation cables and mounted onto the TMJ simulator. Realistic jaw motions were generated through the application of the following muscle forces: lateral pterygoid muscle, suprahyoid depressors (geniohyoid, mylohyoid, and digastric muscles), and elevator muscles. To simulate muscle contraction, cables were inserted into the mandible at the center area of each muscle's attachment. To provide a minimum mouth closing force at the initial position, the elevator muscles were combined at the anterior mandible. During mandibular movement, each motion was recorded using a high-resolution laser scanner. The right TMJ of the same head was reconstructed with a total TMJ prosthesis. The same forces were applied and the jaw motions were recorded again. CT scan was performed and 3-dimensional CT models of the skull with TMJ prosthesis were generated. Results Mandibular motions, before and after TMJ replacement, with and without lateral pterygoid muscle reattachment, were re-created in a cadaveric preparation. The laser-scanned data during the mandibular motion were used to drive 3-dimensional CT models. A movie for each mandibular motion was subsequently created for motion path analysis. Compared with mandibular motion before TMJ replacement, mandibular lateral and protrusive motions after TMJ replacement, with and without lateral pterygoid muscle reattachment, were greatly limited. The jaw motion recorded before total joint replacement was applied to the mandibular and prostheses models after total TMJ replacement. The condylar component was observed sinking into the fossa during jaw motion. Conclusion A motion simulator capable of re-creating and recording full range of mandibular motions in a cadaveric preparation has been developed. It can be used to simulate mandibular motions for the intact TMJ and total joint prosthesis, and to re-create and record their full range of mandibular motions. In addition, the full range of the recorded motion can be re-created as motion images in a computer. These images can be used for motion path analysis and to study the causation of limited range of motion after total joint replacement and strategies for improvement. PMID:21050636

Investigation of predictors affecting food mixing ability in mandibulectomy and/or glossectomy patients.

PubMed

Otomaru, Takafumi; Sumita, Yuka I; Chang, Qingan; Fueki, Kenji; Igarashi, Yoshimasa; Taniguchi, Hisashi

2009-07-01

Several previous reports have described factors that affect masticatory function. However, there are no known predictors that affect the food mixing ability of the masticatory function, and it has been impossible to predict masticatory function in mandibulectomy and/or glossectomy patients. The purpose of the present study was to develop a numerical formula that could predict the food mixing ability of the masticatory function among mandibulectomy and/or glossectomy patients. The null hypothesis of the study was that five predictors, namely mandibulectomy, mandibular continuity, number of residual mandibular teeth, occlusal units and tongue movement score, were unable to account for the mixing ability index (MAI) in mandibulectomy and/or glossectomy patients. The subjects were 20 patients who had undergone mandibulectomy and/or glossectomy. The above-described five predictors were assessed. Tongue movement was evaluated with a tongue movement test and the MAI was evaluated with a mixing ability test. Multiple regression analysis was used to examine whether the five predictors affected the MAI after prosthetic treatment. A regression equation was determined for the five predictors (R(2)=0.83; adjusted R(2)=0.77; p<0.001). The obtained regression equation could successfully account for the MAI in mandibulectomy and/or glossectomy patients.

Relationship between vertical facial patterns and dental arch form in class II malocclusion.

PubMed

Grippaudo, Cristina; Oliva, Bruno; Greco, Anna Lucia; Sferra, Simone; Deli, Roberto

2013-11-07

The purpose of this study is to evaluate the relationship between dental arch form and the vertical facial pattern determined by the angle between the mandibular plane and the anterior cranial base (Sella-nasion/mandibular plane angle (SN-MP)) in skeletal class II untreated patients. A sample of 73 Caucasians patients with untreated skeletal class II in permanent dentition was divided into three groups according to the values of the angle SN-MP. An evaluation of the arch form was performed by angular and linear relation values on each patient. Regression analysis was used to determine the statistical significance of the relationships between SN-MP angle and dental arch form. The differences among the three groups were analyzed for significance using a variance analysis. A decrease of the upper arch transversal diameters in high SN-MP angle patients and an increase in low angle SN-MP ones (P<0.05) were shown. Result analysis showed a change in upper arch shape, with a smaller intercanine width in patients with high SN-MP angle and a greater one in low angle patients. As SN-MP angle increased, the upper arch form tended to be narrower. No statistically significant difference in mandibular arch form among the three groups was found, except the angle value related to incisors position. The results showed the association between the upper dental arch form and the vertical facial pattern. On the contrary, the lower arch form was not related to the mandibular divergence.

Association between third molar agenesis patterns and agenesis of other teeth in a Japanese orthodontic population.

PubMed

Endo, Saori; Sanpei, Sugako; Ishida, Rieko; Sanpei, Shinya; Abe, Ryota; Endo, Toshiya

2015-01-01

The purpose of this study was to investigate the patterns of third molar agenesis and incidence of agenesis of other permanent teeth in a Japanese orthodontic patient group. A total of 417 Japanese subjects (134 males and 283 females) with agenesis of one or more third molars were divided into four groups according to the agenesis pattern, and 874 other Japanese subjects (302 males and 572 females) without third molar agenesis were assigned to a control group. Panoramic radiographs and medical and dental records were used to examine for tooth agenesis. The Chi-square test and odds ratio were used to make statistical comparisons. The prevalence of third molar agenesis worked out at 32.3% with no statistically significant gender difference. A high prevalence rate of agenesis of third molars, unilateral or bilateral, could be considered characteristic of the Japanese orthodontic population. Significant increases in occurrence of oligodontia, and unilateral or bilateral agenesis of other teeth, including maxillary lateral incisors and maxillary and mandibular second premolars, were observed in all or almost all of the third molar agenesis groups, compared with the controls. A significantly increased prevalence rate of mandibular lateral incisor agenesis was observed in almost all of the third molar agenesis groups. The Japanese patients with third molar agenesis had a significantly increased occurrence of oligodontia, and unilateral or bilateral agenesis of maxillary and mandibular lateral incisors and second premolars, except for bilateral agenesis of mandibular lateral incisors.

BIOMECHANICAL ANALYSIS OF THE STRESSES GENERATED BY DIFFERENT DISOCCLUSION PATTERNS IN AN IMPLANT-SUPPORTED MANDIBULAR COMPLETE DENTURE

PubMed Central

Greco, Gustavo Diniz; Jansen, Wellington Corrêa; Landre, Janis; Seraidarian, Paulo Isaías

2009-01-01

Objectives: This study evaluated by three-dimensional finite element analysis the tensions generated by different disocclusion patterns (canine guide and bilateral balanced occlusion) in an implant-supported mandibular complete denture. Material and Methods: A three-dimensional model of implant-supported mandibular complete denture was fabricated according to the Brånemark protocol. A 5-element 3.75 x 13-mm screw-shape dental implant system was modeled for this study. The implants were located in the intermental foramen region with 3-mm-high prosthetic components joined by a nickel-chromium framework with 12-mm bilateral cantilever covered by acrylic resin and 12 acrylic denture teeth. SolidWorks® software was used before and after processing the simulations. The mechanical properties of the components were inserted in the model and a 15 N load was established in fixed points, in each one of the simulations. Data were collected in the entire nickel-chromium framework. The results were displayed three-dimensionally as color graphic scales. Results: The canine guide generated greater tensions in the region of the first implant, while the bilateral balanced occlusion generated great tensions in the entire metallic framework. The maximum tension found in the simulation of the bilateral balanced occlusion was 3.22 fold higher than the one found in the simulation of the disocclusion in canine guide. Conclusion: The pattern of disocclusion in canine guide is the ideal for implant-supported mandibular complete denture. PMID:19936535

Biomechanical analysis of the stresses generated by different disocclusion patterns in an implant-supported mandibular complete denture.

PubMed

Greco, Gustavo Diniz; Jansen, Wellington Corrêa; Landre Junior, Janis; Seraidarian, Paulo Isaías

2009-01-01

This study evaluated by three-dimensional finite element analysis the tensions generated by different disocclusion patterns (canine guide and bilateral balanced occlusion) in an implant-supported mandibular complete denture. A three-dimensional model of implant-supported mandibular complete denture was fabricated according to the Brånemark protocol. A 5-element 3.75 x 13-mm screw-shape dental implant system was modeled for this study. The implants were located in the inter-mental foramen region with 3-mm-high prosthetic components joined by a nickel-chromium framework with 12-mm bilateral cantilever covered by acrylic resin and 12 acrylic denture teeth. SolidWorks software was used before and after processing the simulations. The mechanical properties of the components were inserted in the model and a 15 N load was established in fixed points, in each one of the simulations. Data were collected in the entire nickel-chromium framework. The results were displayed three-dimensionally as color graphic scales. The canine guide generated greater tensions in the region of the first implant, while the bilateral balanced occlusion generated great tensions in the entire metallic framework. The maximum tension found in the simulation of the bilateral balanced occlusion was 3.22 fold higher than the one found in the simulation of the disocclusion in canine guide. The pattern of disocclusion in canine guide is the ideal for implant-supported mandibular complete denture.

Treatment of Pediatric Condylar Fractures: A 20-Year Experience.

PubMed

Ghasemzadeh, Ali; Mundinger, Gerhard S; Swanson, Edward W; Utria, Alan F; Dorafshar, Amir H

2015-12-01

The purpose of this study was to define patterns of injury and treatment for condylar and subcondylar fractures and evaluate short-term outcomes in the pediatric population. A retrospective chart review was performed on pediatric patients with mandibular condylar fractures who presented between 1990 and 2010. Computed tomographic imaging was reviewed for all patients to assess fracture characteristics. Mandibular fractures were codified using the Strasbourg Osteosynthesis Research Group and Lindahl classification methods. Sixty-four patients with 92 condylar fractures were identified. Of these patients, 29 had isolated condylar fracture and 35 had a condylar fracture associated with an additional mandibular arch fracture. The most common fracture patterns were diacapitular fracture in the Strasbourg Osteosynthesis Research Group system (n = 46) and vertical condylar head fracture in the Lindahl system (n = 14). Condylar fracture with additional mandibular arch fractures were treated with maxillomandibular fixation more often than patients with condylar fracture [n = 40 (74.1 percent) versus n = 14 (25.9 percent); p = 0.004]. No condylar fracture was treated in an open fashion. Forty-three patients returned for follow-up. The median follow-up period was 81 days (interquartile range, 35 to 294 days). Ten patients had complications (23.3 percent). The most common complication was malocclusion (n = 5). Nine of 10 patients with complications had condylar fracture with an additional mandibular arch fracture. Closed treatment of condylar fractures yields satisfactory results in pediatric patients. Pediatric patients with condylar fractures combined with additional arch fractures experience a higher rate of unfavorable outcomes.

Cone-beam computed tomography as advanced diagnostic aid in endodontic treatment of molars with multiple canals: Two case reports

PubMed Central

Kamble, Amit Pralhad; Pawar, Rohini Rangarao; Mattigatti, Sudha; Mangala, T. M.; Makandar, Saleem

2017-01-01

The purpose of these case reports is to emphasize the importance of knowledge regarding the root canal morphology and current diagnostic aids one should have as both of these important factors going to affect the prognosis of the endodontic treatment. These two case reports describe the maxillary and mandibular first molars with multiple canals. After clinical and radiographic diagnosis, additional help of cone-beam computed tomography (CBCT) of mandibular molar has been taken to evaluate the morphology and canal pattern; while maxillary molar was evaluated using CBCT scan to evaluate the canal configuration and obturation. In CBCT evaluation, the mandibular molar was diagnosed with six separated canals with three mesial and three distal canals and with radix paramolaris and radix entomolaris. The maxillary molar had five canals with three mesiobuccal (MB) canals. Both molars were instrumented with conventional hand and rotary file systems and obturated by conventional lateral compaction method. The axial images from CBCT show Vertucci Type VIII canal pattern in both roots of first mandibular molars and in MB root of maxillary first molar Sert and Bayirli Type XVIII canal configuration and no accessory canal in distobuccal and palatal root. With the recent innovations in diagnostic and operating aids, we can come across many variations in the root canal morphology of both mandibular and maxillary teeth, especially multi-rooted one (i.e., molars), and the knowledge of which leads to successful endodontic treatment with an excellent prognosis. PMID:29259367

[Comparative study of root canal morphology of mandibular first premolar by micro-CT and radio visio graphy].

PubMed

Li, Xiangjie; Liu, Na; Liu, Rui; Dong, Zhengmou; Liu, Luchuan; Deng, Manjing

2012-02-01

To compare the consistency of root canal configuration types of mandibular first premolar by using micro-CT and radio visio graphy (RVG). One hundred extracted mandibular first premolars with complete dental root and apex which received no endodontic treatment were randomly selected. Each tooth was radiographed with RVG through a buccolingual and mesiodistal direction, and then scanned with micro-CT and reconstructed. The classifications of the root canal types according to Vertucci's type with the two methods were compared. The canal patterns were classified as type I (67%), type III (3%), type V (18%), type VII (2%), additional type (10%) with micro-CT and canal patterns as type I (71%), type III (2%), type V (23%), type VII (1%), additional type (3%) with RVG. 63% of teeth showed one canal in both micro-CT and RVG. Only 25% of teeth were diagnosed as complex canal by the same canal type in both micro-CT and RVG. The Kappa value between micro-CT and RVG was 0.541 which suggested that the two kinds of methods had intermediate consistency. 82.8% of the premolars with root groove had two or more than two canals. Although RVG can basically reflect the root canal system type of the mandibular first premolars in vitro, it offers poor accuracy images to complex root canals. Micro-CT three-dimensional images could clearly and precisely display the root canal system morphology of the mandibular first pre-molars in vitro.

Restoration of a vertical alveolar bone defect by orthodontic relocation of a mesially impacted mandibular first molar.

PubMed

Kim, Sung-Jin; Kim, Jin-Wook; Choi, Tae-Hyun; Lee, Kee-Joon

2015-04-01

An impacted mandibular first molar tends to cause serious bone defects of the adjacent teeth. When choosing between the 2 typical treatment options-extraction or orthodontic relocation of the impacted tooth-the decision should be based on assessment of the prognosis. A 22-year-old man with severe mesioangulation and impaction of the mandibular first molar and a related vertical bone defect on the distal side of the second premolar was treated with extraction of the second molar and orthodontic relocation of the first molar with a retromolar miniscrew. Comprehensive orthodontic treatment involving premolar extraction was conducted. Strategic extraction of the molar and adequate orthodontic movement helped to restore the bone structure on the affected side. This case report suggests the effectiveness of restoration of bone defects by using viable periodontal tissues around the impacted tooth for the longevity of the periodontium. Copyright © 2015 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

[Observation of oral actions using digital image processing system].

PubMed

Ichikawa, T; Komoda, J; Horiuchi, M; Ichiba, H; Hada, M; Matsumoto, N

1990-04-01

A new digital image processing system to observe oral actions is proposed. The system provides analyses of motion pictures along with other physiological signals. The major components are a video tape recorder, a digital image processor, a percept scope, a CCD camera, an A/D converter and a personal computer. Five reference points were marked on the lip and eyeglasses of 9 adult subjects. Lip movements were recorded and analyzed using the system when uttering five vowels and [ka, sa, ta, ha, ra, ma, pa, ba[. 1. Positions of the lip when uttering five vowels were clearly classified. 2. Active articulatory movements of the lip were not recognized when uttering consonants [k, s, t, h, r[. It seemed lip movements were dependent on tongue and mandibular movements. Downward and rearward movements of the upper lip, and upward and forward movements of the lower lip were observed when uttering consonants [m, p, b[.

Management of pediatric mandibular fracture: a case series.

PubMed

Agarwal, Ravi M; Yeluri, Ramakrishna; Singh, Chanchal; Chaudhry, Kalpna; Munshi, Autar K

2014-09-01

A pediatric mandibular fracture can cause a child severe pain and the parent or caregiver extreme worry. While the pattern of fractures and associated injuries in children is similar to adults, the incidence is low. Due to a number of factors, including the anatomical complexity of the developing mandible in a child, management of such fractures differs from that of adults and can greatly challenge the pediatric dentist. Various treatment modalities of managing mandibular fracture are available, such as closed/open cap splint with circummandibular wiring, arch-bar fixation, and cementation of the cap splint. This article reviews 19 cases in the management of pediatric facial fracture using varied treatment methods.

Comparison of Periodontal Ligament Injection and Inferior Alveolar Nerve Block in Mandibular Primary Molars Pulpotomy: A Randomized Control Trial

PubMed Central

Haghgoo, Roza; Taleghani, Ferial

2015-01-01

Background: Inferior alveolar nerve block is a common technique for anesthesia of the primary mandibular molars. A number of disadvantages have been shown to be associated with this technique. Periodontal ligament (PDL) injection could be considered as an alternative to inferior alveolar nerve block. The aim of this study was to evaluate the effectiveness of PDL injection in the anesthesia of primary molar pulpotomy with mandibular block. Methods: This study was performed using a sequential double-blind randomized trial design. 80 children aged 3-7 years old who required pulpotomy in symmetrical mandibular primary molars were selected. The teeth of these children were anesthetized with periodontal injection on one side of the mandible and block on the other. Pulpotomy was performed on each patient during the same appointment. Signs of discomfort, including hand and body tension and eye movement, the verbal complaint and crying (SEM scale), were evaluated by a dental assistant who was blinded to the treatment allocation of the patients. Finally, the data were analyzed using the exact Fisher test and Pearson Chi-squared exact test. Results: Success rate was 88/75 and 91/25 in the PDL injection and nerve block groups, respectively. There was no statistically significant difference between the two techniques (P = 0.250). Conclusion: Results showed that PDL injection can be used as an alternative to nerve block in pulpotomy of the mandibular primary molars. PMID:26028895

Mandibular angle resection and masticatory muscle hypertrophy - a technical note and morphological optimization.

PubMed

Andreishchev, A R; Nicot, R; Ferri, J

2014-11-01

Mandibular angle resection is rarely used, but is a highly effective means of correcting facial defects. We report a mandibular angle resection technique associated with the removal of a part of hypertrophic masseter muscles and resection of buccal fat pad. Anatomical reminders: the most important entities are the facial artery and vein, crossing the lower margin of the jaw just in front of the anterior boarder of the masseter muscle and the temporomaxillary vein, passing through the temporomaxillary fossa; preoperative aspects: the preoperative examination included a radiological assessment of the shape and size of the mandibular angle; surgical technique: an intra-oral approach was usually used. The most effective and convenient method for the osteotomy was using a reciprocating saw. This technique allowed achieving a smooth contour of masseter muscles during masticatory movements or at rest. Eleven mandibular angle resections were performed from 2001 to 2009. The surgery was supplemented by remodeling the lower margin of the jaw for 5 other patients. No permanent facial palsy was noted. One patient presented a unilateral long-term loss of sensitivity of the lower lip and chin. This surgical technique if simple even requires using good technical equipment, and observing a set of rules. Using these principles allows simplifying the surgical technique, and decreasing its morbidity. A part of the masseter muscles and the buccal fat pad can sometimes be resected to improve the morphological results. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

Surgical Treatment of the Atrophic Mandibular Fractures by Locked Plates Systems: Our Experience and a Literature Review

PubMed Central

Novelli, Giorgio; Sconza, Cristiano; Ardito, Emanuela; Bozzetti, Alberto

2012-01-01

The management of atrophic mandibular fractures in edentulous patients represents an insidious issue for the maxillofacial surgeon due to the biological and biomechanical conditions that are unfavorable for fracture fixation and bone healing. The purpose of this study was to evaluate the results of the treatment of atrophic mandibular fractures and to compare the outcomes of different plating systems used for stabilization. We selected a study group of 16 patients with fractures of completely edentulous atrophic mandibles who were treated in our department between 2004 and 2010. All patients were surgically treated by open reduction and internal rigid fixation using 2.0-mm large-profile locking and 2.4-mm locking bone plates. All patients achieved a complete fracture healing and fast functional recovery of mandibular movements without intraoperative or postoperative surgical complications. The results of our study demonstrated the efficacy of this type of treatment in association with a low postoperative complication rate, a reduction in the recovery time, and the possibility to have an immediately functional rehabilitation. There were very similar results using each of the two bone plating methods considered: no case had hardware failure or nonunion of the fracture. The 2.0-mm large locking plate is thinner, exposes through the soft tissues less frequently, and is much easier to shape and adapt to the mandibular anatomy. However, the 2.4-mm locking plate system still represents the reference hardware in the condition of severe bone atrophy. PMID:23730420

Soldier-Specific Modification of the Mandibular Motor Neurons in Termites

PubMed Central

Ishikawa, Yuki; Aonuma, Hitoshi; Miura, Toru

2008-01-01

Social insects exhibit a variety of caste-specific behavioral tendencies that constitute the basis of division of labor within the colony. In termites, the soldier caste display distinctive defense behaviors, such as aggressively attacking enemies with well-developed mandibles, while the other castes retreat into the colony without exhibiting any aggressive response. It is thus likely that some form of soldier-specific neuronal modification exists in termites. In this study, the authors compared the brain (cerebral ganglion) and the suboesophageal ganglion (SOG) of soldiers and pseudergates (workers) in the damp-wood termite, Hodotermopsis sjostedti. The size of the SOG was significantly larger in soldiers than in pseudergates, but no difference in brain size was apparent between castes. Furthermore, mandibular nerves were thicker in soldiers than in pseudergates. Retrograde staining revealed that the somata sizes of the mandibular motor neurons (MdMNs) in soldiers were more than twice as large as those of pseudergates. The enlargement of MdMNs was also observed in individuals treated with a juvenile hormone analogue (JHA), indicating that MdMNs become enlarged in response to juvenile hormone (JH) action during soldier differentiation. This enlargement is likely to have two functions: a behavioral function in which soldier termites will be able to defend more effectively through relatively faster and stronger mandibular movements, and a developmental function that associates with the development of soldier-specific mandibular muscle morphogenesis in termite head. The soldier-specific enlargement of mandibular motor neurons was observed in all examined species in five termite families that have different mechanisms of defense, suggesting that such neuronal modification was already present in the common ancestor of termites and is significant for soldier function. PMID:18612458

Influence of implant number on the movement of mandibular implant overdentures.

PubMed

Oda, Ken; Kanazawa, Manabu; Takeshita, Shin; Minakuchi, Shunsuke

2017-03-01

The rotational movement of an implant overdenture (IOD) has a negative effect on the perceived masticatory ability of the denture wearer. However, the influence of implant number on the movement of IODs has not been investigated. The purpose of this in vitro study was to evaluate the denture movement of mandibular IODs anchored by different numbers of implants. An edentulous mandibular test model with artificial mucosa and 5 experimental overdentures (N=5) was fabricated. The locator attachment system with blue nylon inserts was chosen for this study. Three implant positions were prepared: anterior midline (1-IOD), bilateral lateral incisor regions (2-IOD), and anterior midline and bilateral canine regions (3-IOD). Vertical loads of 50 N were applied to the mid-anterior region, the left canine region, the left premolar region, and the left first molar region. The vertical and horizontal displacements at the right distal edge and the vertical displacements at the loading point were measured. The displacement values were statistically analyzed using a 1-way analysis of variance and the post hoc Tukey honest significant difference test with the implant number as a factor. In addition, the values of the vertical and horizontal displacements at the distal edge of the overdenture were statistically compared using a paired t test, and the values of the vertical displacement at the distal edge of the overdenture were statistically analyzed by a repeated measures analysis of variance and the post hoc Tukey honest significance difference test with the loading point as a factor (a=.05). Upon anterior loading, the 2-IOD showed significantly larger vertical displacements at the right distal edge than the 1-IOD or 3-IOD (P<.01). The horizontal displacements at the right distal edge were small compared with the vertical displacements at the same point, although the displacement of the 2-IOD was significantly larger than that of the 1-IOD upon anterior loading (P=.03). The magnitude of the vertical displacement at the loading point of the 2-IOD was significantly larger than that of the 3-IOD upon anterior loading (P<.01). No statistically significant differences were shown under the other conditions for each loading (P>.05). Within the limitations of this in vitro study, the following conclusions were drawn: During mastication with the anterior teeth, the use of 2 implants for anchoring an IOD increased the rotation of the denture base more than the use of 1 or 3 implants. The horizontal movements of the IODs were small compared with the vertical movements. Denture movement under the occlusal force in the molar region was smaller than that in the anterior region. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Semireal Time Monitoring Of The Functional Movements Of The Mandible

NASA Astrophysics Data System (ADS)

Isaacson, Robert J.; Baumrind, Sheldon; Curry, Sean; Molthen, Robert A.

1983-07-01

Many branches of dental practice would benefit from the availability of a relatively accurate, precise, and efficient method for monitoring the movements of the human mandible during function. Mechanical analog systems have been utilized in the past but these are difficult to quantify, have limited accuracy due to frictional resistance of the components, and contain information only on the borders of the envelopes of possible movement of the landmarks measured (rather than on the functional paths of the landmarks which lie within their envelopes). Those electronic solutions which have been attempted thus far have been prohibitively expensive and time consuming for clinical use, have had lag times between data acquisition and display, or have involved such restrictions of freedom of motion as to render ambiguous the meaning of the data obtained. We report work aimed at developing a relatively non-restrictive semi-real time acoustical system for monitoring the functional movement of the mandible relative to the rest of the head. A set of three sparking devices is mounted to the mandibular component of a light, relatively non-constraining extra-oral harness and another set of three sparkers is attached to the harness' cranial or skull component. The sparkers are fired sequentially by a multiplexer and the sound associated with each firing is recorded by an array of three or more microphones. Computations based on the known speed of sound are used to evaluate the distances between the sparkers and the microphones. These data can then be transformed by computer to provide numeric or graphic information on the movement of selected mandibular landmarks with respect to the skull. Total elapsed time between the firing of the sparkers and the display of graphic information need not exceed 30-60 seconds using even a relatively modest modern computer.

Functional reconstruction of total lower lip defects using innervated gracilis flap in the setting of high-energy ballistic injury to the lower face: preliminary report.

PubMed

Gurunluoglu, Raffi; Glasgow, Mark; Williams, Susan A; Gurunluoglu, Aslin; Antrobus, Jarod; Eusterman, Vincent

2012-10-01

Reconstruction of total full-thickness lower lip defects combined with extensive composite mandibular defects particularly in the setting of close-range high-energy ballistic injury presents a formidable challenge for the reconstructive plastic surgeon. While the fibular flap has been widely accepted for its usefulness in the reconstruction of composite mandibular defects, to date, there is no definitive widely established method of total lower lip reconstruction. The article presents authors' approach using innervated gracilis muscle flap for total lower lip reconstruction in the setting of high-energy gunshot injuries to the face. Three patients underwent composite mandibular defect reconstruction using fibular osteocutaneous flap and functional lower lip reconstruction using innervated gracilis muscle flap. Lip lining was reconstructed using the skin paddle of the fibular flap. The external surface of the gracilis muscle was skin-grafted. Facial artery myomucosal flap provided vermilion reconstruction in two patients. All fibular (n=3) and gracilis flap transfers (n=3) were viable. An electromyographic study at 1 year postoperatively demonstrated successful re-innervation of the gracilis muscle. Starting at about 10 weeks postoperatively, patients exhibited voluntary lip movements and oral competence. In addition, all patients achieved near-normal speech, evidence of recovered protective sensitivity and satisfactory appearance. The mean follow-up was 16.1 months. Our preliminary report in three patients demonstrated that innervated gracilis muscle transfer combined with fibular flap provides a successful reconstruction of extensive composite mandibular and total lower lip defects resulting from gunshot injuries to the face. Oral continence was achieved by combination of regained tonicity and voluntary movement of the gracilis muscle following re-innervation and assistance of the cheek muscles on the gracilis muscle. The described technique was reliable and the results were promising. Copyright © 2012 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

A within-subject comparison of mandibular long-bar and hybrid implant-supported prostheses: evaluation of masticatory function.

PubMed

Tang, L; Lund, J P; Taché, R; Clokie, C M; Feine, J S

1999-09-01

Sixteen edentulous subjects participated in a within-subject crossover clinical trial to test the hypotheses that a long-bar overdenture attached to 4 implants gives greater patient satisfaction and masticatory efficiency than a two-implant hybrid overdenture. All subjects were given a new maxillary conventional denture. Ten received mandibular long-bar overdentures first and six the hybrid overdentures. Two months later, psychometric assessments and functional tests were repeated 3 times at one-week intervals. The mandibular prosthesis was then changed, and recordings were repeated after another 2 months. Mandibular movements and electromyographic activity of jaw muscles were recorded while subjects chewed standard-sized pieces of 5 foods: bread, cheese, apple, sausage, and carrot. Measurements included masticatory time, cleaning time (the time between the end of mastication and the last swallow), and duration and amplitude of masticatory cycles and phases. Multilevel analyses were performed. No significant differences in masticatory time were found between prostheses for any test food. However, cleaning time for carrot [estimated mean of difference (delta) +/- SE: 1.6 sec +/- 0.7] and bread (delta = 1.0 sec +/- 0.4) was slightly but significantly longer for subjects wearing long-bar overdentures. Cycle duration was longer with the long-bar overdenture only for subjects chewing carrot. The opening phase was shorter and the closing phase longer with the long-bar overdenture for almost all test foods. Vertical amplitude was significantly less with the long-bar overdenture for cheese (delta = -2.6 mm +/- 1.1), apple (delta = -2.6 mm +/- 1.0), and sausage (delta = -2.9 mm +/- 1.3). These results suggest that mastication with the 2 prostheses is equally efficient, although clearance of some foods from the mouth is longer with the long-bar overdentures. They also indicate that patients adapt their masticatory movements to the characteristics of different prostheses.

Mandibular condylar morphology for bruxers with different grinding patterns.

PubMed

Tao, Jianxiang; Wu, Junhua; Zhang, Xuying

2015-12-29

The purpose of this study was to investigate the mandibular condylar morphology for bruxers with different grinding patterns. Condylar sectional morphology and condylar position of 30 subjects were determined by two viewers using cone beam computed tomography (CBCT) image data sets. The grinding patterns during sleep bruxism (SB) were determined objectively using a Brux-checker device.Chi-square tests were used for statistical analysis for the condylar morphology type between different tooth grinding patterns. Spearman's rank correlation coefficient was used for correlation analysis between condylar position and the canine guidance area during SB. Theincidence of condylarmorphologicaldivergence from idealwas35%.There isa significant difference in distribution of condylar morphology type between the group grinding (GG) and GG combined with mediotrusive side grinding (MG) (Pv 0.05). There was no significant correlation between condylar position and canine guidance area during bruxism. MG during SB is associated with condylar morphology that is considered not to be ideal.

Mandibular condylar morphology for bruxers with different grinding patterns.

PubMed

Tao, Jianxiang; Wu, Junhua; Zhang, Xuying

2016-07-01

The purpose of this study was to investigate the mandibular condylar morphology for bruxers with different grinding patterns. Condylar sectional morphology and condylar position of 30 subjects were determined by two viewers using cone beam computed tomography (CBCT) image data sets. The grinding patterns during sleep bruxism (SB) were determined objectively using a Brux-checker device.Chi-square tests were used for statistical analysis for the condylar morphology type between different tooth grinding patterns. Spearman's rank correlation coefficient was used for correlation analysis between condylar position and the canine guidance area during SB. Theincidence of condylarmorphologicaldivergence from idealwas35%.There isa significant difference in distribution of condylar morphology type between the group grinding (GG) and GG combined with mediotrusive side grinding (MG) (p < 0.05). There was no significant correlation between condylar position and canine guidance area during bruxism. MG during SB is associated with condylar morphology that is considered not to be ideal.

Evolutionarily conserved morphogenetic movements at the vertebrate head-trunk interface coordinate the transport and assembly of hypopharyngeal structures.

PubMed

Lours-Calet, Corinne; Alvares, Lucia E; El-Hanfy, Amira S; Gandesha, Saniel; Walters, Esther H; Sobreira, Débora Rodrigues; Wotton, Karl R; Jorge, Erika C; Lawson, Jennifer A; Kelsey Lewis, A; Tada, Masazumi; Sharpe, Colin; Kardon, Gabrielle; Dietrich, Susanne

2014-06-15

The vertebrate head-trunk interface (occipital region) has been heavily remodelled during evolution, and its development is still poorly understood. In extant jawed vertebrates, this region provides muscle precursors for the throat and tongue (hypopharyngeal/hypobranchial/hypoglossal muscle precursors, HMP) that take a stereotype path rostrally along the pharynx and are thought to reach their target sites via active migration. Yet, this projection pattern emerged in jawless vertebrates before the evolution of migratory muscle precursors. This suggests that a so far elusive, more basic transport mechanism must have existed and may still be traceable today. Here we show for the first time that all occipital tissues participate in well-conserved cell movements. These cell movements are spearheaded by the occipital lateral mesoderm and ectoderm that split into two streams. The rostrally directed stream projects along the floor of the pharynx and reaches as far rostrally as the floor of the mandibular arch and outflow tract of the heart. Notably, this stream leads and engulfs the later emerging HMP, neural crest cells and hypoglossal nerve. When we (i) attempted to redirect hypobranchial/hypoglossal muscle precursors towards various attractants, (ii) placed non-migratory muscle precursors into the occipital environment or (iii) molecularly or (iv) genetically rendered muscle precursors non-migratory, they still followed the trajectory set by the occipital lateral mesoderm and ectoderm. Thus, we have discovered evolutionarily conserved morphogenetic movements, driven by the occipital lateral mesoderm and ectoderm, that ensure cell transport and organ assembly at the head-trunk interface. Copyright © 2014 The Authors. Published by Elsevier Inc. All rights reserved.

Evolutionarily conserved morphogenetic movements at the vertebrate head–trunk interface coordinate the transport and assembly of hypopharyngeal structures

PubMed Central

Lours-Calet, Corinne; Alvares, Lucia E.; El-Hanfy, Amira S.; Gandesha, Saniel; Walters, Esther H.; Sobreira, Débora Rodrigues; Wotton, Karl R.; Jorge, Erika C.; Lawson, Jennifer A.; Kelsey Lewis, A.; Tada, Masazumi; Sharpe, Colin; Kardon, Gabrielle; Dietrich, Susanne

2014-01-01

The vertebrate head–trunk interface (occipital region) has been heavily remodelled during evolution, and its development is still poorly understood. In extant jawed vertebrates, this region provides muscle precursors for the throat and tongue (hypopharyngeal/hypobranchial/hypoglossal muscle precursors, HMP) that take a stereotype path rostrally along the pharynx and are thought to reach their target sites via active migration. Yet, this projection pattern emerged in jawless vertebrates before the evolution of migratory muscle precursors. This suggests that a so far elusive, more basic transport mechanism must have existed and may still be traceable today. Here we show for the first time that all occipital tissues participate in well-conserved cell movements. These cell movements are spearheaded by the occipital lateral mesoderm and ectoderm that split into two streams. The rostrally directed stream projects along the floor of the pharynx and reaches as far rostrally as the floor of the mandibular arch and outflow tract of the heart. Notably, this stream leads and engulfs the later emerging HMP, neural crest cells and hypoglossal nerve. When we (i) attempted to redirect hypobranchial/hypoglossal muscle precursors towards various attractants, (ii) placed non-migratory muscle precursors into the occipital environment or (iii) molecularly or (iv) genetically rendered muscle precursors non-migratory, they still followed the trajectory set by the occipital lateral mesoderm and ectoderm. Thus, we have discovered evolutionarily conserved morphogenetic movements, driven by the occipital lateral mesoderm and ectoderm, that ensure cell transport and organ assembly at the head–trunk interface. PMID:24662046

Design and finite element analysis of a novel sliding rod microscrew implantation device for mandibular prognathism

PubMed Central

Li, Yanfeng; Lv, Yuan; Lu, Yongjin; Zeng, Pan; Zeng, Xianglong; Guo, Xiaoqian; Han, Weili

2015-01-01

Tooth distalization is an effective approach for mandibular prognathism. Current distalization devices are bulky and clinically complicated. Here, we designed a novel molar distalization device by using a sliding rod and a microscrew and performed a mechanical analysis and finite element model (FEM) analysis of force distribution and displacement of the upper canine, first and second premolar and first molar. A 2D FEM was constructed using the Beam3 element and a 3D FEM was constructed of the mandibular teeth, the periodontal membrane, and the alveolar bones using the UG software. The upper first molar was divided into 12 points on the dental surface to facilitate stress analysis. Force analysis using the ANSYS WORKBECNH revealed that, both horizontally and vertically, the traction force causing distalization of the first molar decreased when the spring coil moved down the L shaped sliding rod. The 3D FEM force analysis revealed distomedial displacement of the upper first molar when the sliding rod microscrew implantation device caused distalization of the molar. These findings support further exploration for the use of the sliding rod microscrew implants as an anchorage for group distal movement of the teeth of patients with mandibular prognathism. PMID:26379860

Growth trajectories in the cave bear and its extant relatives: an examination of ontogenetic patterns in phylogeny.

PubMed

Fuchs, Manuela; Geiger, Madeleine; Stange, Madlen; Sánchez-Villagra, Marcelo R

2015-11-02

The study of postnatal ontogeny can provide insights into evolution by offering an understanding of how growth trajectories have evolved resulting in adult morphological disparity. The Ursus lineage is a good subject for studying cranial and mandibular shape and size variation in relation to postnatal ontogeny and phylogeny because it is at the same time not diverse but the species exhibit different feeding ecologies. Cranial and mandibular shapes of Ursus arctos (brown bear), U. maritimus (polar bear), U. americanus (American black bear), and the extinct U. spelaeus (cave bear) were examined, using a three-dimensional geometric morphometric approach. Additionally, ontogenetic series of crania and mandibles of U. arctos and U. spelaeus ranging from newborns to senile age were sampled. The distribution of specimens in morphospace allowed to distinguish species and age classes and the ontogenetic trajectories U. arctos and U. spelaeus were found to be more similar than expected by chance. Cranial shape changes during ontogeny are largely size related whereas the evolution of cranial shape disparity in this clade appears to be more influenced by dietary adaptation than by size and phylogeny. The different feeding ecologies are reflected in different cranial and mandibular shapes among species. The cranial and mandibular shape disparity in the Ursus lineage appears to be more influenced by adaptation to diet than by size or phylogeny. In contrast, the cranial and mandibular shape changes during postnatal ontogeny in U. arctos and U. spelaeus are probably largely size related. The patterns of morphospace occupation of the cranium and the mandible in adults and through ontogeny are different.

Treatment of Pediatric Condylar Fractures: A 20-Year Experience

PubMed Central

Ghasemzadeh, Ali; Mundinger, Gerhard S.; Swanson, Edward W.; Utria, Alan F.; Dorafshar, Amir H.

2016-01-01

Background The purpose of this study was to define patterns of injury and treatment for condylar and subcondylar fractures and evaluate short-term outcomes in the pediatric population. Methods A retrospective chart review was performed on pediatric patients with mandibular condylar fractures who presented between 1990 and 2010. Computed tomographic imaging was reviewed for all patients to assess fracture characteristics. Mandibular fractures were codified using the Strasbourg Osteosynthesis Research Group and Lindahl classification methods. Results Sixty-four patients with 92 condylar fractures were identified. Of these patients, 29 had isolated condylar fracture and 35 had a condylar fracture associated with an additional mandibular arch fracture. The most common fracture patterns were diacapitular fracture in the Strasbourg Osteosynthesis Research Group system (n = 46) and vertical condylar head fracture in the Lindahl system (n = 14). Condylar fracture with additional mandibular arch fractures were treated with maxillomandibular fixation more often than patients with condylar fracture [n = 40 (74.1 percent) versus n = 14 (25.9 percent); p = 0.004]. No condylar fracture was treated in an open fashion. Forty-three patients returned for follow-up. The median follow-up period was 81 days (interquartile range, 35 to 294 days). Ten patients had complications (23.3 percent). The most common complication was malocclusion (n = 5). Nine of 10 patients with complications had condylar fracture with an additional mandibular arch fracture. Conclusions Closed treatment of condylar fractures yields satisfactory results in pediatric patients. Pediatric patients with condylar fractures combined with additional arch fractures experience a higher rate of unfavorable outcomes. PMID:26595021

[Using dynamic magnetotherapy and transdermal electroneurostimulation in the combined treatment of patients with mandibular fractures and concomitant periodontal inflammatory diseases].

PubMed

Lepilin, A V; Erokina, N L; Rogatina, T V; Khlusov, I Iu

2009-01-01

The objective of this study was to compare results of dynamic magnetotherapy (DMT), transdermal electroneurostimulation (TDENS), and traditional ultrahigh frequency (UHF) therapy in 473 patients with mandibular fractures and concomitant inflammatory diseases of paradontium. The parameters measured in the study included hygienic and paradontal indices, microcirculation patterns (using laser Doppler flowmetry), and the degree of mandibular fragment consolidation. It was shown that combined treatment with DMT and TDENS using an AMO-ATOS-E apparatus permits to eliminate clinical symptoms of paradontal inflammatory diseases twice as fast as traditional ultrahigh frequency therapy and ensures a two-fold reduction in the frequency of complications.

An Assessment of Correlation between Dermatoglyphic Patterns and Sagittal Skeletal Discrepancies

PubMed Central

Philip, Biju; Madathody, Deepika; Mathew, Manu; Paul, Jose; Dlima, Johnson Prakash

2017-01-01

Introduction Investigators over years have been fascinated by dermatoglyphic patterns which has led to the development of dermatoglyphics as a science with numerous applications in various fields other than being the best and most widely used method for personal identification. Aim To assess the correlation between dermatoglyphic patterns and sagittal skeletal discrepancies. Materials and Methods A total of 180 patients, aged 18-40 years, were selected from those who attended the outpatient clinic of the Deparment of Orthodontics and Dentofacial Orthopedics, Mar Baselios Dental College, Kothamangalam, Kerala, India. The fingerprints of both hands were taken by ink and stamp method after proper hand washing. The patterns of arches, loops and whorls in fingerprints were assessed. The total ridge count was also evaluated. Data was also sent to the fingerprint experts for expert evaluation. The sagittal jaw relation was determined from the patient’s lateral cephalogram. The collected data was then statistically analyzed using Chi-square tests, ANOVA and Post-hoc tests and a Multinomial regression prediction was also done. Results A significant association was observed between the dermatoglyphic pattern exhibited by eight fingers and the sagittal skeletal discrepancies (p<0.05). An increased distribution of whorl pattern was observed in the skeletal Class II with maxillary excess group and skeletal Class II with mandibular deficiency group while an increased distribution of loop pattern was seen in the skeletal Class III with mandibular excess group and skeletal Class III with maxillary deficiency group. Higher mean of total ridge count was also seen in the groups of skeletal Class II with maxillary excess and skeletal Class II with mandibular deficiency. Multinomial regression predicting skeletal pattern with respect to the fingerprint pattern showed that the left thumb impression fits the best model for predicting the skeletal pattern. Conclusion There was a significant association between dermatoglyphic patterns and sagittal skeletal discrepancies. Dermatoglyphics could serve as a cost effective screening tool of these craniofacial problems. PMID:28511506

Impaction of lower third molars and their association with age: radiological perspectives.

PubMed

Ryalat, Soukaina; AlRyalat, Saif Aldeen; Kassob, Zaid; Hassona, Yazan; Al-Shayyab, Mohammad H; Sawair, Faleh

2018-04-04

Third molars are the most commonly impacted teeth, and their extraction is the most commonly performed procedure in oral and maxillofacial surgery. The aim of the present study is to describe the pattern of mandibular third molar impaction and to define the most appropriate age for prophylactic extraction of mandibular third molar teeth. A total of 1198 orthopantomographs (OPGs) with 1810 impacted lower third molars were reviewed by two authors. The pattern of eruption in relation to patient's age was examined using standard radiographic points and angles. Statistical analysis was performed using SPSS for Windows release 16.0 (SPSS Inc., Chicago, IL, USA). In patients older than 20 years, vertical pattern of impaction was the most common (21.4%); while in young patients; horizontal impaction was more common (21.3%). Furthermore, there was a constant pattern of increase in Pell-Gregory ramus class 1 with increasing age, as the prevalence of class 1 was 0% at age 18 years compared to 54.9% at the age of 26 years. Frequency of vertical impaction of lower third molars was seen more at an older age (> 20 years) in this study, with an increase in the retromolar space. Late extraction of mandibular third molar teeth (i.e. after the age of 20) is therefore recommended when prophylactic extraction is considered.

Increased sternocleidomastoid, but not trapezius, muscle activity in response to increased chewing load.

PubMed

Häggman-Henrikson, Birgitta; Nordh, Erik; Eriksson, Per-Olof

2013-10-01

Previous findings, during chewing, that boluses of larger size and harder texture result in larger amplitudes of both mandibular and head-neck movements suggest a relationship between increased chewing load and incremental recruitment of jaw and neck muscles. The present report evaluated jaw (masseter and digastric) and neck [sternocleidomastoid (SCM) and trapezius] muscle activity during the chewing of test foods of different sizes and textures by 10 healthy subjects. Muscle activity was recorded by surface electromyography and simultaneous mandibular and head movements were recorded using an optoelectronic technique. Each subject performed continuous jaw-opening/jaw-closing movements whilst chewing small and large boluses of chewing gum and rubber silicone (Optosil). For jaw opening/jaw closing without a bolus, SCM activity was recorded for jaw opening concomitantly with digastric activity. During chewing, SCM activity was recorded for jaw closing concomitantly with masseter activity. Trapezius activity was present in some, but not all, cycles. For the masseter and SCM muscles, higher activity was seen with larger test foods, suggesting increased demand and recruitment of these muscles in response to an increased chewing load. This result reinforces the previous notion of a close functional connection between the jaw and the neck motor systems in jaw actions and has scientific and clinical significance for studying jaw function and dysfunction. © 2013 Eur J Oral Sci.

Unpredictability of soft tissue changes after camouflage treatment of Class II division 1 malocclusion with maximum anterior retraction using miniscrews.

PubMed

Kim, Kayoung; Choi, Sung-Hwan; Choi, Eun-Hee; Choi, Yoon-Jeong; Hwang, Chung-Ju; Cha, Jung-Yul

2017-03-01

To compare soft and hard tissue responses based on the degree of maxillary incisor retraction using maximum anchorage in patients with Class II division 1 malocclusion. This retrospective study sample was divided into moderate retraction (<8.0 mm; n = 28) and maximum retraction (≥8.0 mm; n = 29) groups based on the amount of maxillary incisor retraction after extraction of the maxillary and mandibular first premolars for camouflage treatment. Pre- and posttreatment lateral cephalograms were analyzed. There were 2.3 mm and 3.0 mm of upper and lower lip retraction, respectively, in the moderate group; and 4.0 mm and 5.3 mm, respectively, in the maximum group. In the moderate group, the upper lip was most influenced by posterior movement of the cervical point of the maxillary incisor (β = 0.94). The lower lip was most influenced by posterior movement of B-point (β = 0.84) and the cervical point of the mandibular incisor (β = 0.83). Prediction was difficult in the maximum group; no variable showed a significant influence on upper lip changes. The lower lip was highly influenced by posterior movement of the cervical point of the maxillary incisor (β = 0.50), but this correlation was weak in the maximum group. Posterior movement of the cervical point of the anterior teeth is necessary for increased lip retraction. However, periodic evaluation of the lip profile is needed during maximum retraction of the anterior teeth because of limitations in predicting soft tissue responses.

External and internal anatomy of third molars.

PubMed

Guerisoli, D M; de Souza, R A; de Sousa Neto, M D; Silva, R G; Pécora, J D

1998-01-01

The external and internal anatomy of 269 third molars (155 maxillary and 114 mandibular) were studied. The teeth were measured, classified according to their root number and shape and the internal anatomy was observed by the use of diaphanization. A great anatomical variability was found, with the presence of up to 5 roots in maxillary third molars and 3 roots in mandibular third molars. The number of root canals followed the same pattern.

Rhythmic chewing with oral jaws in teleost fishes: a comparison with amniotes.

PubMed

Gintof, Chris; Konow, Nicolai; Ross, Callum F; Sanford, Christopher P J

2010-06-01

Intra-oral prey processing (chewing) using the mandibular jaws occurs more extensively among teleost fishes than previously documented. The lack of muscle spindles, gamma-motoneurons and periodontal afferents in fishes makes them useful for testing hypotheses regarding the relationship between these sensorimotor components and rhythmic chewing in vertebrates. Electromyography (EMG) data from the adductor mandibulae (AM) were used to quantify variation in chew cycle duration in the bowfin Amia, three osteoglossomorphs (bony-tongues), four salmonids and one esocid (pike). All species chewed prey using their oral jaw in repetitive trains of between 3 and 30 consecutive chews, a pattern that resembles cyclic chewing in amniote vertebrates. Variance in rhythmicity was compared within and between lineages using coefficients of variation and Levene's test for homogeneity of variance. These comparisons revealed that some teleosts exhibit degrees of rhythmicity that are comparable to mammalian mastication and higher than in lepidosaurs. Moreover, chew cycle durations in fishes, as in mammals, scale positively with mandible length. Chewing among basal teleosts may be rhythmic because it is stereotyped and inflexible, the result of patterned interactions between sensory feedback and a central pattern generator, because the lack of a fleshy tongue renders jaw-tongue coordination unnecessary and/or because stereotyped opening and closing movements are important for controlling fluid flow in the oral cavity.

Patterns Associated with Adult Mandibular Fractures in Southern Taiwan—A Cross-Sectional Retrospective Study

PubMed Central

Lin, Ko-Chien; Peng, Shu-Hui; Kuo, Pao-Jen; Chen, Yi-Chun; Rau, Cheng-Shyuan; Hsieh, Ching-Hua

2017-01-01

Purpose: This study aimed to determine the patterns associated with adult mandibular fractures from a Level-I trauma center in southern Taiwan. Methods: The data of adult trauma patients admitted between 1 January 2009 and 31 December 2014 were retrieved from the Trauma Registry System and retrospectively reviewed. Fracture site and cause of injury were categorized into groups for comparison, and corresponding odds ratios (ORs) and 95% confidence intervals (CIs) were obtained by multivariate logistic regression. Results: Motorcycle accidents were the most common cause of mandibular fractures (76.3%), followed by falls (10.9%), motor vehicle accidents (4.8%), and being struck by/against objects (4.5%). Of the 503 cases of mandibular fractures, the condylar neck and head were the most common sites (32.0%), followed by the parasymphysis (21.7%), symphysis (19.5%), angle and ramus (17.5%), and body (9.3%). The location of mandibular fractures in patients who had motorcycle accidents was similar to that in all patients. Motor vehicle accidents resulted in a significantly higher number of body fractures (OR 3.3, 95% CI 1.24–8.76, p = 0.017) and struck injury in a significantly higher number of angle and ramus fractures (OR 3.9, 95% CI 1.48–10.26, p = 0.006) compared to motorcycle accidents. The helmet-wearing status and body weight were not associated with the location of mandibular fractures in motorcycle accidents. Conclusions: Our study revealed that the anatomic fracture sites of mandible were specifically related to different etiologies. In southern Taiwan, motorcycle accidents accounted for the major cause of mandibular fractures and were associated with the condylar neck and head as the most frequent fracture sites. In contrast, motor vehicle accidents and struck injuries tended to cause more body fracture as well as angle and ramus fracture compared to motorcycle accidents. Furthermore, the status of helmet-wearing and body weight were not associated with the location of mandible fractures caused by motorcycle accidents. PMID:28737727

[Finite element analysis of mechanical characteristics during retracting mandibular incisors through sliding mechanics].

PubMed

Gu, Yong-Jia; Wu, Yan-Ping; Gao, Mei-Qin; Yao, Ning; Chen, Wen-Jing

2008-10-01

To analyze the mechanical characteristic changes of teeth and arch under different loading direction during retracting mandibular incisors through implant, simulating clinical loading system. Three- dimensional finite element model, including brackets, archwire, crampable hooks and implants, was reconstructed. The force direction was determined by connecting the points in crampable hook and the center point of implant, and the force point and force direction were changed with the adjustment of the height of crampable hook and the height of implant. Then three-dimensional movement trend of teeth, stress distribution in periodontal membrane and the largest displacement of archwire nodes in each group were calculated and analyzed. SPSS13.0 software package was used for statistical analysis. It was found that the height of implant and the height of crampable hook were correlated with the movement of teeth and stress distribution in periodontal membrane (P<0.01). The movement trend of teeth in the condition of different height of implant and different height of crampable hook was illustrated as follows:(1)with the height increase of crampable hook, the movement trend of the central and lateral incisors varied from mesial lingual tipping to mesial labial tipping. However, canines tipped distally and lingually; the second premolars tipped mesially and lingually, and the first molar roots tipped distally and buccally with decreasing tipping angle. (2) The largest stress distribution in the whole arch was located in the labial apical one-third area of the lateral incisors, while that of canines and the first molars was located in the alveolar ridges and root bifurcations. These findings indicate that the different movement trend during retracting anterior teeth can be achieved through the adjustment of the height of crampable hook, and implant, anchorage can effectively control anterior movement of the posterior teeth. Supported by Research Fund of Bureau of Science and Technology of Nantong City (Grant No. S40023).

Stress distribution in the temporo-mandibular joint discs during jaw closing: a high-resolution three-dimensional finite-element model analysis.

PubMed

Savoldelli, Charles; Bouchard, Pierre-Olivier; Loudad, Raounak; Baque, Patrick; Tillier, Yannick

2012-07-01

This study aims at analysing the stresses distribution in the temporomandibular joint (TMJ) using a complete high-resolution finite element model (FE Model). This model is used here to analyse the stresses distribution in the discs during a closing jaw cycle. In the end, this model enables the prediction of the stress evolution in the TMJ disc submitted to various loadings induced by mandibular trauma, surgery or parafunction. The geometric data for the model were obtained from MRI and CT scans images of a healthy male patient. Surface and volume meshes were successively obtained using a 3D image segmentation software (AMIRA(®)). Bone components of skull and mandible, both of joint discs, temporomandibular capsules and ligaments and dental arches were meshed as separate bodies. The volume meshes were transferred to the FE analysis software (FORGE(®)). Material properties were assigned for each region. Boundary conditions for closing jaw simulations were represented by different load directions of jaws muscles. The von Mises stresses distribution in both joint discs during closing conditions was analyzed. The pattern of von Mises stresses in the TMJ discs is non-symmetric and changed continuously during jaw movement. Maximal stress is reached on the surface disc in areas in contact with others bodies. The three-dimension finite element model of masticatory system will make it possible to simulate different conditions that appear to be important in the cascade of events leading to joint damage.

Mechanics in the Production of Mandibular Fractures: A Clinical, Retrospective Case-Control Study

PubMed Central

Yang, Rongtao; Li, Zhi; Li, Zubing

2016-01-01

As the mandible is susceptible to fracture, the aim of this study was to use multivariate logistic regression analysis to identify and distinguish various internal factors that may influence the location of mandibular fractures. The study included 1131 patients with maxillofacial fractures during the period from January 2000 to December 2009 to evaluate the association of mandibular fracture location (unilateral symphysis, body, angle, condylar, or bilateral condylar fractures) with various internal factors. Among the 1131 patients, 869 had mandibular fractures. Data on age, sex, soft tissue injuries, dental trauma, and maxillofacial fracture type were collected and analyzed using multivariate logistic regression. In total, 387, 210, 139, 319, and 172 patients were diagnosed with unilateral symphysis, body, angle, unilateral, or bilateral condylar fractures, respectively. The dental trauma in patients with bilateral condylar fractures differed from that in patients with unilateral condylar fractures. Patients with mandibular fracture (unilateral symphysis, body, unilateral or bilateral condylar) possessed an approximately equal risk of soft tissue injuries in the mandible. Patients with either unilateral or bilateral condylar fractures were associated with a low risk of mandibular angle fracture (OR < 1). Similarly, patients with mandibular angle fracture were associated with a low risk of unilateral or bilateral condylar fractures (OR < 1). Moreover, patients with symphysis fracture were associated with a low risk of bilateral condylar fractures (90 of 387 [23.3%], OR 0.899). By contrast, patients with bilateral condylar fractures were associated with a high risk of symphysis fracture (90 of 172 [52.3%], OR 17.38). Patients with condylar fractures, particularly those with bilateral condylar fractures, were infrequently associated with secondary mandibular fractures. Mandibular fractures tended to have less of an association with midfacial fractures. The occurrence of mandibular fractures is strongly correlated with age, sex, soft tissue injuries, dental trauma, and the pattern and position of the maxillofacial fractures in patients. PMID:26900699

Maxillary and mandibular contribution to the establishment of class II malocclusion in an adult Lebanese population.

PubMed

El Hajj, Nadine; Bassil-Nassif, Nayla; Tauk, Alain; Mouhanna-Fattal, Carole; Bouserhal, Joseph P

2017-12-01

The main aim of this study was to describe the contribution of the maxilla and the mandible to the establishment of a Class II skeletal malocclusion in an adult Lebanese population. Secondary aims were to detect the presence of sex-based dimorphism and to study the influence of the vertical dimension on the Class II skeletal pattern. A sample of 90 adults in skeletal Class II was recruited and equally distributed according to sex and vertical typology. The study describes the skeletal and dentoalveolar cephalometric characteristics of the Class II sample, essentially according to Coben's cephalometric analysis. The total effective depth of the cranial base and the anterior cranial base angle (SN-BaH) were both greater in the Class II sample. In females, the effective depth of the maxilla (Ptm-A) was larger than normal while SNB was smaller. The parameters describing the size and shape of the body of the mandible were significantly different from those of normal subjects. The upper incisors were in a retrusive position, while the axis of the lower incisors was located normally. The mandibular molars had a more distal sagittal position. Hyperdivergent subjects had more significant posterior alveolar growth, a more retrusive mandibular position and smaller mandibular dimensions than the other two vertical sub-groups. The cranial base contributes to the establishment of a Class II malocclusion, and mandibular retrusion cannot be considered as a characteristic shared by all skeletal Class II subjects. Lessening of the absolute length of the mandibular body is the second most frequent etiological factor noted in the Class II sample studied. Most individuals in skeletal Class II have an associated dental Class II malocclusion, and the vertical dimension has an influence on the Class II skeletal pattern. Copyright © 2017 CEO. Published by Elsevier Masson SAS. All rights reserved.

Anesthetic technique for inferior alveolar nerve block: a new approach

PubMed Central

PALTI, Dafna Geller; de ALMEIDA, Cristiane Machado; RODRIGUES, Antonio de Castro; ANDREO, Jesus Carlos; LIMA, José Eduardo Oliveira

2011-01-01

Background Effective pain control in Dentistry may be achieved by local anesthetic techniques. The success of the anesthetic technique in mandibular structures depends on the proximity of the needle tip to the mandibular foramen at the moment of anesthetic injection into the pterygomandibular region. Two techniques are available to reach the inferior alveolar nerve where it enters the mandibular canal, namely indirect and direct; these techniques differ in the number of movements required. Data demonstrate that the indirect technique is considered ineffective in 15% of cases and the direct technique in 1329% of cases. Objective Objective: The aim of this study was to describe an alternative technique for inferior alveolar nerve block using several anatomical points for reference, simplifying the procedure and enabling greater success and a more rapid learning curve. Materials and Methods A total of 193 mandibles (146 with permanent dentition and 47 with primary dentition) from dry skulls were used to establish a relationship between the teeth and the mandibular foramen. By using two wires, the first passing through the mesiobuccal groove and middle point of the mesial slope of the distolingual cusp of the primary second molar or permanent first molar (right side), and the second following the oclusal plane (left side), a line can be achieved whose projection coincides with the left mandibular foramen. Results The obtained data showed correlation in 82.88% of cases using the permanent first molar, and in 93.62% of cases using the primary second molar. Conclusion This method is potentially effective for inferior alveolar nerve block, especially in Pediatric Dentistry. PMID:21437463

A Cephalometric Comparison of Twin Block and Bionator Appliances in Treatment of Class II Malocclusion

PubMed Central

Ahmadian-Babaki, Fatemeh; Araghbidi-Kashani, S. Mehdi

2017-01-01

Background Class II malocclusion is one of the most common orthodontic problems. In cases of class II malocclusion with mandibular deficiency, functional appliances often are used with the intent of stimulating mandibular growth. Bionator and twin block are two of the more popular functional appliances. The aim of this study was to compare the treatment outcomes of these two appliances using cephalometric radiographs. Material and Methods Cephalometric radiographs of 33 patients who had class II division I malocclusion, before and after treatment were digitalized. The mean changes in twin block and bionator groups were compared using independent t test. Results Twin block and bionator showed no statistically significant differences in cephalometric parameters except for ANB, NA-Pog, Basal and Ar-Go-Me angles. Conclusions There were no statistically significant differences in dentoalveolar and mandibular position between twin block and bionator (p>0.1). Twin block was more efficient in inhibition of forward movement of maxilla (p<0.1). Key words:Functional, Class II malocclusion, Cephalometrics, Twin block, Bionator, Treatment. PMID:28149473

Distal extension mandibular removable partial denture with implant support

PubMed Central

Bural, Canan; Buzbas, Begum; Ozatik, Sebnem; Bayraktar, Gulsen; Emes, Yusuf

2016-01-01

This case report describes the fabrication of a distal extension removable partial denture (RPD) of a 65-year-old man with implant support. Loss of fibroelasticity of the peripheral tissues and reduced mandibular vestibular sulcular depth due to a previous surgical resection and radiotherapy at the right side were the main clinical factors that created difficulty for denture retention and stability. The fabrication of a mandibular RPD supported by anterior teeth and two bilaterally placed implants in the molar area to convert from Kennedy Class 1 design to Kennedy Class 3 implant-bounded RPD is reported. Retention and stability of the denture were improved with implant support on the distal extension site of the RPD. The common clinical problems about distally extended RPDs are lack of retention and stability due to the movement around the rotational axis. Dental implant placement to the distal edentulous site minimizes the potential dislodgement of the RPD is popular. Implant-supported RPD can be suggested as an advantageous and cost-effective treatment option for the partially edentulous patients. PMID:28042277

Dual odontogenic origins develop at the early stage of rat maxillary incisor development.

PubMed

Kriangkrai, Rungarun; Iseki, Sachiko; Eto, Kazuhiro; Chareonvit, Suconta

2006-03-01

Developmental process of rat maxillary incisor has been studied through histological analysis and investigation of tooth-related gene expression patterns at initial tooth development. The tooth-related genes studied here are fibroblast growth factor-8 (Fgf-8), pituitary homeobox gene-2 (Pitx-2), sonic hedgehog (Shh), muscle segment homeobox-1 (Msx-1), paired box-9 (Pax-9) and bone morphogenetic protein-4 (Bmp-4). The genes are expressed in oral epithelium and/or ectomesenchyme at the stage of epithelial thickening to the early bud stage of tooth development. Both the histological observation and tooth-related gene expression patterns during early stage of maxillary incisor development demonstrate that dual odontogenic origins aligned medio-laterally in the medial nasal process develop, subsequently only single functional maxillary incisor dental placode forms. The cascade of tooth-related gene expression patterns in rat maxillary incisor studied here is quite similar to those of the previous studies in mouse mandibular molar, even though the origins of oral epithelium and ectomesenchyme involved in development of maxillary incisor and mandibular molar are different. Thus, we conclude that maxillary incisor and mandibular molar share a similar signaling control of Fgf-8, Pitx-2, Shh, Msx-1, Pax-9 and Bmp-4 genes at the stage of oral epithelial thickening to the early bud stage of tooth development.

Dental arch dimensional changes after adenotonsillectomy in prepubertal children.

PubMed

Petraccone Caixeta, Anna Cristina; Andrade, Ildeu; Bahia Junqueira Pereira, Tatiana; Franco, Letícia Paiva; Becker, Helena Maria Gonçalves; Souki, Bernardo Quiroga

2014-04-01

The purposes of this study were to investigate the dental arch changes after adenotonsillectomies in prepubertal children and to compare the dental arch dimensions of mouth-breathing and nasal-breathing children. The sample included 49 prepubertal severely obstructed mouth-breathing children and 46 prepubertal nasal-breathing children. Twenty-four of the 49 mouth-breathing children had an adenotonsillectomy and composed the adenotonsillectomy subgroup. The 25 children in whom the mouth-breathing pattern was unchanged during the 1-year study period composed the control subgroup. The mouth-breathing children showed a deeper palatal vault, a larger mandibular width, and a larger mandibular arch length in comparison with the nasal-breathing children. After airway clearance, the adenotonsillectomy group showed a significant maxillary transverse width gain compared with the control subgroup. The control subgroup showed a significant deepening of the palatal height when compared with the adenotonsillectomy subgroup after 1 year. The adenotonsillectomy subgroup had a significantly different pattern of arch development compared with the untreated controls. After adenotonsillectomy, the mouth-breathing children showed greater maxillary transverse development than did the controls. The palatal vault deepened in the untreated children. The mouth-breathing children showed a deeper palatal vault, a larger mandibular width, and a larger mandibular arch length in comparison with the nasal-breathing children. Copyright © 2014 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Control factors in removable complete dentures: from the articulation quintet to kinetic contact

PubMed Central

Pompa, Giorgio; Giovannetti, Agostino; Gentile, Tina; Di Carlo, Stefano

2010-01-01

Summary Hanau’s laws and the so-called articulation quintet have contributed greatly to the evolution of the prosthetic dentistry and have been further elaborated by various authors. The main aim of this study was to establish the stability of prosthetic plates by attaining balanced occlusion. Several authors have addressed the problem of removable and fixed prostheses by classifying mandibular movements into functional and parafunctional movements which extends the classical occlusal mechanics for the modern occlusal feedback model. Moreover, they suggest the use of the angle of convergence as a reference plane when manufacturing prosthetic. PMID:22238706

Fracture patterns in the maxillofacial region: a four-year retrospective study

PubMed Central

2015-01-01

Objectives The facial bones are the most noticeable area in the human body, and facial injuries can cause significant functional, aesthetic, and psychological complications. Continuous study of the patterns of facial bone fractures and changes in trends is helpful in the prevention and treatment of maxillofacial fractures. The purpose of the current clinico-statistical study is to investigate the pattern of facial fractures over a 4-year period. Materials and Methods A retrospective analysis of 1,824 fracture sites was carried out in 1,284 patients admitted to SMG-SNU Boramae Medical Center for facial bone fracture from January 2010 to December 2013. We evaluated the distributions of age/gender/season, fracture site, cause of injury, duration from injury to treatment, hospitalization period, and postoperative complications. Results The ratio of men to women was 3.2:1. Most fractures occurred in individuals aged between teens to 40s and were most prevalent at the middle and end of the month. Fractures occurred in the nasal bone (65.0%), orbital wall (29.2%), maxillary wall (15.3%), zygomatic arch (13.2%), zygomaticomaxillary complex (9.8%), mandibular symphysis (6.5%), mandibular angle (5.9%), mandibular condyle (4.9%), and mandibular body (1.9%). The most common etiologies were fall (32.5%) and assault (26.0%). The average duration of injury to treatment was 6 days, and the average hospitalization period was 5 days. Eighteen postoperative complications were observed in 17 patients, mainly infection and malocclusion in the mandible. Conclusion This study reflects the tendency for trauma in the Seoul metropolitan region because it analyzes all facial fracture patients who visited our hospital regardless of the specific department. Distinctively, in this study, midfacial fractures had a much higher incidence than mandible fractures. PMID:26734557

Etiology and patterns of pediatric mandibular fractures in Portugal: a retrospective study of 10 years.

PubMed

Ferreira, Pedro Costa; Amarante, José Manuel; Silva, Alvaro Catarino; Pereira, José Miguel; Cardoso, Maria Augusta; Rodrigues, Jorge Manuel

2004-05-01

To determine the pattern of occurrence of mandibular fractures in the pediatric population in Portugal. This retrospective study reviews the records of patients 18 years of age or younger from the 10-year period 1993 to 2002. Age, gender, anatomic site, cause of the accident, weekly and monthly variation, location and type of fractures, presence and location of associated injuries, treatment methods, and complications were reviewed. During this 10-year period, 521 patients with 681 mandibular fractures were treated. Motor-vehicle accident (MVA) was the most common (53.9% patients) cause of fracture. Almost half of the patients (48.8%) were in the oldest age group (16 to 18 years old). The condyle of the mandible was involved in 31.0% of the fractures. Maxillomandibular (MMF) fixation was used in 534 (78.4%) fractures. Overall mortality in this series was 0.6% (3 patients); mortality was caused by multiple traumas, mainly head trauma. There is a need to reinforce legislation aimed to prevent MVA and the total enforcement of existing laws to reduce maxillofacial injuries among children and adolescents.

Alteration of functional loads after tongue volume reduction.

PubMed

Ye, W; Duan, Y Z; Liu, Z J

2013-11-01

An earlier study revealed that the patterns of biomechanical loads on bones around the tongue altered significantly right after tongue volume reduction surgery. The current study was to examine whether these alterations persist or vanish over time post-surgery. Five sibling pairs of 12-week-old Yucatan minipigs were used. For each pair, one had surgery reducing tongue volume by about 15% (reduction) while the other had same incisions without tissue removal (sham). All animals were raised for 4 weeks after surgery. Three rosette strain gauges were placed on the bone surfaces of pre-maxilla (PM), mandibular incisor (MI), and mandibular molar (MM); two single-element gauges were placed across the pre-maxilla-maxillar suture (PMS) and mandibular symphysis (MSP), and two pressure transducers were placed on the bone surfaces of hard palate (PAL) and mandibular body (MAN). These bone strains and pressures were recorded during natural mastication. Overall amount of all loads increased significantly as compared to those in previous study in all animals. Instead of decreased loads in reduction animals as seen in that study, shear strains at PM, MI, and MM, tensile strains at PMS, and pressure at MAN were significantly higher in reduction than sham animals. Compared to the sham, strain dominance shifted at PM, MI, and MM and orientation of tensile strain altered at MI in reduction animals. A healed volume-reduced tongue may change loading regime significantly by elevating loading and altering strain-dominant pattern and orientation on its surrounding structures, and these changes are more remarkable in mandibular than maxillary sites. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Dentoskeletal and Soft Tissue Effects in the Treatment of Class II Malocclusion with Klammt's Elastic Open Activator.

PubMed

Inamassu-Lemes, Sheila Marques; Fuziy, Acácio; Costa, André Luiz Ferreira; Carvalho, Paulo Eduardo Guedes; Nahás-Scocate, Ana Carla Raphaelli

2016-01-01

The purpose of this study was to evaluate the dentoskeletal and soft tissue effects resulting from treatment with Klammt's elastic open activator (EOA) functional orthopedic appliance in patients with Class II malocclusion characterized by mandibular deficiency. Teleradiographs were evaluated in the lateral aspect of the initial (T1) and final (T2) orthopedic phases for 16 patients with Class II, Division 1 malocclusion. The age range was from 9 to 11.2 years, with a mean age of 9.9 years. The cephalometric points were demarcated, and cephalometric measurements were obtained by the same investigator to avoid interobserver variability. The EOA promoted increased lower anterior facial height (LAFH), increased effective mandibular length, clockwise rotation of the mandible, retrusion and verticalization of the upper incisors, proclination and protrusion of the lower incisors, extrusion of the upper molars, mesial movement of the lower molars and anterior projection of the lower lip. Skeletal changes characterized by an increase in mandibular length and dentoalveolar changes with an emphasis on the verticalization and retrusion of the upper incisors, proclination of the lower incisors and mesial positioning of the lower molars were key to improving the occlusal relationship and esthetic facial factors. The EOA is well indicated in patients with Class II malocclusion due to mandibular deficiency with increased overbite, proclined upper incisors and verticalized lower incisors.

Morphofunctional Analysis of the Quadrate of Spinosauridae (Dinosauria: Theropoda) and the Presence of Spinosaurus and a Second Spinosaurine Taxon in the Cenomanian of North Africa.

PubMed Central

Hendrickx, Christophe; Mateus, Octávio; Buffetaut, Eric

2016-01-01

Six quadrate bones, of which two almost certainly come from the Kem Kem beds (Cenomanian, Upper Cretaceous) of south-eastern Morocco, are determined to be from juvenile and adult individuals of Spinosaurinae based on phylogenetic, geometric morphometric, and phylogenetic morphometric analyses. Their morphology indicates two morphotypes evidencing the presence of two spinosaurine taxa ascribed to Spinosaurus aegyptiacus and? Sigilmassasaurus brevicollis in the Cenomanian of North Africa, casting doubt on the accuracy of some recent skeletal reconstructions which may be based on elements from several distinct species. Morphofunctional analysis of the mandibular articulation of the quadrate has shown that the jaw mechanics was peculiar in Spinosauridae. In mature spinosaurids, the posterior parts of the two mandibular rami displaced laterally when the jaw was depressed due to a lateromedially oriented intercondylar sulcus of the quadrate. Such lateral movement of the mandibular ramus was possible due to a movable mandibular symphysis in spinosaurids, allowing the pharynx to be widened. Similar jaw mechanics also occur in some pterosaurs and living pelecanids which are both adapted to capture and swallow large prey items. Spinosauridae, which were engaged, at least partially, in a piscivorous lifestyle, were able to consume large fish and may have occasionally fed on other prey such as pterosaurs and juvenile dinosaurs. PMID:26734729

Patients' and sleeping partners' experience of treatment for sleep-related breathing disorders with a mandibular repositioning splint.

PubMed

Bates, C J; McDonald, J P

2006-01-28

To determine in detail the complications associated with the use of mandibular repositioning splints (MRS) to treat sleep-related breathing disorders. This prospective cross-sectional cohort study audits the management with mandibular repositioning splints of 121 patients suffering from sleep-related breathing disorders. Investigation of patients' and sleeping partners' perspectives on treatment was undertaken with the use of a questionnaire based study. Sixty-eight per cent of respondents reported that they were compliant with treatment; various side effects were reported of which excess salivation was the most common. Investigation of sleeping partners' perspectives revealed that 70% felt that their partners' snoring was improved and 47% felt that their partner's breathing pauses during sleep were reduced. Sixty-four per cent of the sleeping partners also reported that their own sleep pattern had improved since their partner's treatment. Mandibular repositioning splints used in the manner described by this paper are demonstrated to have a good compliance rate, provide successful treatment and exhibit only minor, reversible side effects.

Thin-plate spline (TPS) graphical analysis of the mandible on cephalometric radiographs.

PubMed

Chang, H P; Liu, P H; Chang, H F; Chang, C H

2002-03-01

We describe two cases of Class III malocclusion with and without orthodontic treatment. A thin-plate spline (TPS) analysis of lateral cephalometric radiographs was used to visualize transformations of the mandible. The actual sites of mandibular skeletal change are not detectable with conventional cephalometric analysis. These case analyses indicate that specific patterns of mandibular transformation are associated with Class III malocclusion with or without orthopaedic therapy, and visualization of these deformations is feasible using TPS graphical analysis.

Numeric simulation of occlusal interferences in molars restored with ultrathin occlusal veneers.

PubMed

Magne, Pascal; Cheung, Raymond

2017-01-01

Selecting material for a minimally invasive occlusal veneer reconstruction concept requires an understanding of how stresses are distributed during functional and parafunctional forces. The purpose of this in vitro study was to investigate stress distribution in a maxillary molar restored with ultrathin occlusal veneers and subjected by an antagonistic mandibular molar to clenching and working and nonworking movements. A maxillary first molar was modeled from microcomputed tomography (micro-CT) data, using medical image processing software, stereolithography editing/optimizing software, and finite element software. Simulated ultrathin occlusal veneer materials were used. The mandibular molar antagonist was a solid nondeformable geometric entity. Loads simulated clenching, working, and nonworking movements with loading of 500 N. The values of the maximum principal stress were recorded. In the clenching load situation, maximum tensile stresses were located at the occlusal veneer (52 MPa for composite resin versus 47 MPa for ceramic). In the working movement, significant additional tensile stresses were found on the palatal root (87 MPa for composite resin and 85 MPa for ceramic). In the nonworking movement, tensile stress on the ultrathin occlusal veneer increased to 118 MPa for composite resin and 143 MPa for ceramic veneers. Tensile stress peaks shifted to the mesiobuccal root (75 MPa for composite resin and 74 MPa for ceramic). The topography of stresses generated by the various occlusal interferences were clearly identified. Significant tensile stress concentrations were found within the restoration's occlusal topography and root, with the nonworking interference being the most harmful and also the most revealing of the difference between the composite resin and ceramic ultrathin occlusal veneers. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Longitudinal eruptive and posteruptive tooth movements, studied on oblique and lateral cephalograms with implants.

PubMed

Zhang, Xiaoyun; Baumrind, Sheldon; Chen, Gui; Chen, Huizhong; Liang, Yi; Xu, Tianmin

2018-05-01

The purpose of this study was to investigate the eruptive and posteruptive tooth displacements of untreated growing subjects longitudinally and the potential connections between posteruptive displacement of the maxillary and mandibular first molars and skeletal facial growth. The sample comprised 11 series of right 45° oblique cephalograms and lateral cephalograms of untreated children with metallic implants of the Björk type obtained from the archives of a growth study. Cephalograms generated at approximately 2-year intervals between the ages of 8.5 and 16 years were selected and traced. Superimpositions of serial tracings of oblique cephalograms on stable intraosseous implants were made to determine the displacements of buccal segment teeth in both arches, and superimpositions of serial tracings of lateral cephalograms were used to evaluate growth of the jaws. Continuous mesial tipping of the maxillary molars was observed from 8.5 to 16 years of age, averaging 8.2° ± 5.5° for the first molars and 18.3°± 8.5° for the second molars. Compared with the maxillary molars, the mandibular first molars showed less change in angulation except in the later mixed dentition when more than half of the subjects had accelerated forward tipping of the first molar in the late mixed dentition associated with migration into the leeway space. Average amounts of cumulative eruption from 8.5 to 16 years of age were 12.1 ± 2.1 mm downward and 3.8 ± 1.7 mm forward for the maxillary first molar. The mandibular first molar showed 8.6 ± 2.3 mm of eruption and 4.4 ± 1.9 mm of mesial migration. Peak velocity of vertical eruption of the maxillary and mandibular first molars corresponded to the skeletal vertical growth spurt. The maxillary canines and first premolars showed remarkable and continuous uprighting migration during eruption, averaging 9.5° ± 5.0° and 10.5° ± 6.7°, respectively. However, when they erupted into the occlusion, their changes in angulation reverted to forward tipping. The same tendency was also found in the mandibular canines and first premolars. Remarkable eruption and migration occur to the teeth of both arches during childhood and adolescence. Rates of first molar eruption during adolescence follow the general pattern of somatic growth. We infer that maintaining the original distal crown angulation of the maxillary molars may be an effective protocol for preservation of anchorage. Copyright © 2018 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Three-dimensional analysis of postoperative returning movement of perioperative condylar displacement after bilateral sagittal split ramus osteotomy for mandibular setback with different fixation methods.

PubMed

Han, Jeong Joon; Hwang, Soon Jung

2015-11-01

This study aimed to evaluate postoperative returning movement of perioperative condylar displacement after bilateral sagittal split ramus osteotomy (BSSRO) depending on a fixation method using three-dimensional (3D) analysis of computed tomography (CT). Twenty-five mandibular prognathic patients (50 condyles) who underwent orthognathic surgery with BSSRO were divided into three groups depending on the fixation method, which consisted of miniplate only (Group A), combined with single bicortical screw (Group B), or with more than one bicortical screw (Group C). CT data taken before, immediately after, and 3 to 6 months after surgery were analyzed. The condyle exhibited mainly lateral bodily displacement and inward and inferior rotation immediately after surgery. The amount of perioperative lateral displacement of the condyle increased according to the increasing number of fixation screws, but the mean displacements were not significantly different among the three groups. During the postoperative follow-up period, the amount of medial returning of the condyle was 102.2% of the intraoperative lateral displacement in Group A. In contrast, Group B and C exhibited partial returning movement by 71.3% and 38.9% of cases, respectively. In conclusion, stronger rigid internal fixation in orthognathic surgery using BSSRO is associated with reduced flexibility of postoperative functional adjustment of displaced condyle to the preoperative condylar position. Copyright © 2015 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

[Characteristics of opening movement in patients with unilateral mastication].

PubMed

Jia, Ling; Wang, Yun; Wang, Mengya

2016-08-01

To analyze characteristics of mandibular movement in patients with unilateral mastication.
 Undergraduate students in oral medicine from Grade 2011 and 2012 in Wannan Medical College were enrolled for this study by cluster sampling method, which include 30 people with unilateral mastication and 30 people with bilateral mastication. The surface electromyogram (sEMG) of masseter muscle and anterovent of digastric muscle were recorded and the trajectory of mandibular incisor point was recorded simultaneously in the maximum opening and closing movement. The results were analyzed by SPSS 19.0 software.
 Average electrical peak of left anterior digastric muscle and right anterior digastric muscle in the unilateral chewing group was lower than that in the bilateral chewing group (P<0.05). The jaw tangent point trajectory was separate in the unilateral chewing group. There were significant differences at the opening type between the 2 groups. The vertical displacement and the sagittal displacement in the unilateral chewing group were significantly lower than those in the bilateral chewing group (P<0.01). There was significant positive correlation between the average peak potential of masseter muscle and displacement on the right side.
 Average electrical peak of left masseter muscle, left anterior digastric muscle, and right anterior digastric muscle decreases in the unilateral chewing group. Jaw tracking in most people deflects to the working side. Opening and closing jaw tracking is separate in 50% unilateral chewing individuals with the decreased opening degree. Unilateral chewing leads to changes in muscle performance accompanied by trajectory anomalies.

Class III correction using an inter-arch spring-loaded module

PubMed Central

2014-01-01

Background A retrospective study was conducted to determine the cephalometric changes in a group of Class III patients treated with the inter-arch spring-loaded module (CS2000®, Dynaflex, St. Ann, MO, USA). Methods Thirty Caucasian patients (15 males, 15 females) with an average pre-treatment age of 9.6 years were treated consecutively with this appliance and compared with a control group of subjects from the Bolton-Brush Study who were matched in age, gender, and craniofacial morphology to the treatment group. Lateral cephalograms were taken before treatment and after removal of the CS2000® appliance. The treatment effects of the CS2000® appliance were calculated by subtracting the changes due to growth (control group) from the treatment changes. Results All patients were improved to a Class I dental arch relationship with a positive overjet. Significant sagittal, vertical, and angular changes were found between the pre- and post-treatment radiographs. With an average treatment time of 1.3 years, the maxillary base moved forward by 0.8 mm, while the mandibular base moved backward by 2.8 mm together with improvements in the ANB and Wits measurements. The maxillary incisor moved forward by 1.3 mm and the mandibular incisor moved forward by 1.0 mm. The maxillary molar moved forward by 1.0 mm while the mandibular molar moved backward by 0.6 mm. The average overjet correction was 3.9 mm and 92% of the correction was due to skeletal contribution and 8% was due to dental contribution. The average molar correction was 5.2 mm and 69% of the correction was due to skeletal contribution and 31% was due to dental contribution. Conclusions Mild to moderate Class III malocclusion can be corrected using the inter-arch spring-loaded appliance with minimal patient compliance. The overjet correction was contributed by forward movement of the maxilla, backward and downward movement of the mandible, and proclination of the maxillary incisors. The molar relationship was corrected by mesialization of the maxillary molars, distalization of the mandibular molars together with a rotation of the occlusal plane. PMID:24934153

Evaluation of Class II treatment by cephalometric regional superpositions versus conventional measurements.

PubMed

Efstratiadis, Stella; Baumrind, Sheldon; Shofer, Frances; Jacobsson-Hunt, Ulla; Laster, Larry; Ghafari, Joseph

2005-11-01

The aims of this study were (1) to evaluate cephalometric changes in subjects with Class II Division 1 malocclusion who were treated with headgear (HG) or Fränkel function regulator (FR) and (2) to compare findings from regional superpositions of cephalometric structures with those from conventional cephalometric measurements. Cephalographs were taken at baseline, after 1 year, and after 2 years of 65 children enrolled in a prospective randomized clinical trial. The spatial location of the landmarks derived from regional superpositions was evaluated in a coordinate system oriented on natural head position. The superpositions included the best anatomic fit of the anterior cranial base, maxillary base, and mandibular structures. Both the HG and the FR were effective in correcting the distoclusion, and they generated enhanced differential growth between the jaws. Differences between cranial and maxillary superpositions regarding mandibular displacement (Point B, pogonion, gnathion, menton) were noted: the HG had a more horizontal vector on maxillary superposition that was also greater (.0001 < P < .05) than the horizontal displacement observed with the FR. This discrepancy appeared to be related to (1) the clockwise (backward) rotation of the palatal and mandibular planes observed with the HG; the palatal plane's rotation, which was transferred through the occlusion to the mandibular plane, was factored out on maxillary superposition; and (2) the interaction between the inclination of the maxillary incisors and the forward movement of the mandible during growth. Findings from superpositions agreed with conventional angular and linear measurements regarding the basic conclusions for the primary effects of HG and FR. However, the results suggest that inferences of mandibular displacement are more reliable from maxillary than cranial superposition when evaluating occlusal changes during treatment.

Dental and skeletal changes in patients with mandibular retrognathism following treatment with Herbst and pre-adjusted fixed appliance

PubMed Central

Vigorito, Fabio de Abreu; Dominguez, Gladys Cristina; Aidar, Luís Antônio de Arruda

2014-01-01

Objective To assess the dentoskeletal changes observed in treatment of Class II, division 1 malocclusion patients with mandibular retrognathism. Treatment was performed with the Herbst orthopedic appliance during 13 months (phase I) and pre-adjusted orthodontic fixed appliance (phase II). Methods Lateral cephalograms of 17 adolescents were taken in phase I onset (T1) and completion (T2); in the first thirteen months of phase II (T3) and in phase II completion (T4). Differences among the cephalometric variables were statistically analyzed (Bonferroni variance and multiple comparisons). Results From T1 to T4, 42% of overall maxillary growth was observed between T1 and T2 (P < 0.01), 40.3% between T2 and T3 (P < 0.05) and 17.7% between T3 and T4 (n.s.). As for overall mandibular movement, 48.2% was observed between T1 and T2 (P < 0.001) and 51.8% between T2 and T4 (P < 0.01) of which 15.1% was observed between T2 and T3 (n.s.) and 36.7% between T3 and T4 (P < 0.01). Class II molar relationship and overjet were properly corrected. The occlusal plane which rotated clockwise between T1 and T2, returned to its initial position between T2 and T3 remaining stable until T4. The mandibular plane inclination did not change at any time during treatment. Conclusion Mandibular growth was significantly greater in comparison to maxillary, allowing sagittal maxillomandibular adjustment. The dentoalveolar changes (upper molar) that overcorrected the malocclusion in phase I, partially recurred in phase II, but did not hinder correction of the malocclusion. Facial type was preserved. PMID:24713559

Anterior implant-supported overdentures.

PubMed

Ben-Ur, Z; Gorfil, C; Shifman, A

1996-09-01

Retention of complete mandibular dentures can be successfully achieved by means of an implant-retained or natural tooth-retained bar and clip system in the anterior segment of the mandible. The same design principles hold true for both methods of anchoring the retentive bar. These retentive elements must be constructed to allow some freedom of movement around a fulcrum line designed to be perpendicular to the sagittal plane.

Incidence and pattern of mandibular fractures in Rohilkhand region, Uttar Pradesh state, India: A retrospective study

PubMed Central

Giri, Kolli Yada; Singh, Aishwarya Pratap; Dandriyal, Ramakant; Indra, Niranjanaprasad; Rastogi, Sanjay; Mall, Sunil Kumar; Chowdhury, Shouvik; Singh, Himanshu Pratap

2015-01-01

Aims To understand and evaluate the significance of various aetiological factors in determining the incidence and dictating the patterns of mandibular fractures in Rohilkhand region. Methods The patient records and radiographs for 144 patients treated for mandibular fractures were reviewed between the time periods from January 2012 to December 2013. Data on age, gender, aetiology, use of intoxicants, head injury, associated injuries, days of the week, anatomic site and multiple fractures within the mandible were recorded and assessed. Results Maximum incidence of fractures was observed among the individuals in 3rd decade (35.4%) followed by 2nd and 4th decades, which exhibited 32 and 30 cases (22.2% and 20.8%), respectively. Male to female ratio was biased (4:1) portraying a male predominance. Road traffic accidents (RTAs) were observed to be the predominant aetiological factor responsible accounting for 79.2% of the total injuries followed by assaults (11.8%) and falls (9%). Parasymphysis exhibited the highest incidence (32.63%) amongst the anatomic sites, followed by body (18.75%), angle (16.66%), condyle (15.27%), symphysis (12.50%), ramus (2.77%) and coronoid (1.38%). Conclusion The study reveals that majority of affected patients were in the 2nd and 3rd decades. A definitive relationship existed between RTA and the incidence of mandibular fractures. The frequency further increased with consumption of social intoxicants. The most commonly fractured site was parasymphysis either isolated or associated with other fractures in the mandible. PMID:26587379

Management of Chronic Recurrent Dislocation of Temporomandibular Joint Using 'U' Shaped Graft: A New Restrictive Technique.

PubMed

Gadre, Kiran; Singh, Divya; Gadre, Pushkar; Halli, Rajshekhar

2017-06-01

Numerous procedures have been described for the treatment of chronic recurrent dislocation of the temporo-mandibular joint (TMJ), either in the form of enhancement or restriction of the condylar movement, with their obvious merits and demerits. We present a new technique of using U shaped iliac bone graft to restrict the condylar movement and its advantages over the conventional techniques.We have used this technique successfully in 8 cases where Dautrey's procedure had failed with follow up period of 2 years. No patient complained of recurrent dislocation postoperatively. This a very simple and effective technique where other procedures have failed.

Study of the kinematic variables of unilateral and habitual mastication of healthy individuals.

PubMed

Pasinato, Fernanda; Oliveira, Andréia Gussi de; Santos-Couto-Paz, Clarissa C; Zeredo, Jorge Luis Lopes; Bolzan, Geovana de Paula; Macedo, Sergio Bruzadelli; Corrêa, Eliane C R

2017-03-30

To describe and compare the temporal-spatial kinematic variables of mandibular movement during deliberate unilateral and habitual mastication in healthy young-adult individuals. The study sample was composed of eight male healthy volunteers aged 19 to 24 years. The kinematic data were obtained using a motion analysis system - Qualisys Track Manager (QTM) ProReflex MCU. Recordings were performed during deliberate unilateral mastication (UM) and habitual mastication (HM) of firm-consistency gummy candy. The following variables were analyzed: (1) masticatory sequence: duration, number of masticatory cycles, and chewing rate; (2) masticatory cycle: duration, vertical and medial-lateral mandibular range of motion in relation to the skull, and maximum velocity during the opening and closing phases. Data of the variables were compared during UM and HM by the paired t test, and the effect sizes ('d' Cohen) were calculated. Regarding the variables of the masticatory sequence, smaller chewing rate was observed for UM compared with that for HM (1.19±0.21Hz and 1.29±0.16Hz, respectively, p=0.004, d=0.53). Smaller values of maximum velocity during the opening (MU=67.4 mm/s and MH=80.02, p=0.053, d=0.80) and closing (MU=71.77±9.35mm/s and MH=3.51±7mm/s, p=0.014, d=0.79) phases of the masticatory cycle were observed in deliberate unilateral mastication compared with those in habitual mastication. Kinematic variables associated with the sequence and cycle of mastication are influenced by the chewing pattern adopted - deliberate unilateral or habitual.

Endoscopic subcondylar fracture repair: functional, aesthetic, and radiographic outcomes.

PubMed

Lee, C; Mueller, R V; Lee, K; Mathes, S J

1998-10-01

An endoscopic method of mandibular subcondylar fracture repair has been described recently. To determine the effectiveness of this new technique, we longitudinally studied functional, aesthetic, and radiographic parameters following endoscopic repair of 22 subcondylar fractures in 20 patients. Restoration of mandibular function was achieved without postoperative maxillomandibular fixation. Premorbid occlusion was restored. Clinical jaw motion was found to progressively increase with a mean interincisal jaw opening of 43 mm achieved after the eighth postoperative week. Patients were pleased with the aesthetic restoration of their chin projection,jaw line, and the symmetric midline movement of the chin point onjaw opening. Anatomic fracture reduction with rigid plate fixation was confirmed on early postsurgical radiographs. Late radiographs showed fracture union without remodeling of the condylar head. Endoscopic subcondylar fracture repair was efficacious at functional, aesthetic, and radiographic restoration of the mandible.

Temperature changes on the root surfaces of mandibular incisors after an 810-nm high-intensity intracanal diode laser irradiation

NASA Astrophysics Data System (ADS)

da Fonseca Alvarez, Andrea; Moura-Netto, Cacio; Daliberto Frugoli, Alexandre; Fernando, Casemiro; Correa Aranha, Ana Cecilia; Davidowicz, Harry

2012-01-01

Temperature changes caused by laser irradiation can promote damage to the surrounding dental tissues. In this study, we evaluated the temperature changes of recently extracted human mandibular incisors during intracanal irradiation with an 810-nm diode laser at different settings. Fifty mandibular incisors were enlarged up to an apical size of ISO No. 40 file. After the final rinse with 17% ethylenediaminetetraacetic acid, 0.2% lauryl sodium sulfate biologic detergent, and sterile water, samples were irradiated with circular movements from apex to crown through five different settings of output power (1.5, 2.0, 2.5, 3.0, and 3.5 W) in continuous mode. The temperature changes were measured on both sides of the apical and middle root thirds using two thermopar devices. A temperature increase of 7 °C was considered acceptable as a safe threshold when applying the diode laser. Results: The results showed that only 3.5-W output power increased the outer surface temperature above the critical value. Conclusion: The recommended output power can be stipulated as equal to or less than 3 W to avoid overheating during diode laser irradiation on thin dentin walls.

Patients referred for stomatognathic treatment--a survey of 282 patients.

PubMed

Magnusson, T

1984-01-01

The signs and symptoms of mandibular dysfunction and the treatment results were studied in 282 patients referred to the Clinic of Stomatognathic Physiology, Luleå, Sweden. Seventy two per cent of the patients were women. The most common clinical finding was muscles tender to palpation, which was found in 60% of the patients, but other signs such as TMJ-clickings (27%) and limited mandibular movement (16%) were common, as were interferences in the retruded position (33%) and on the non-working side (19%). Splint therapy, therapeutic exercises for the lower jaw and occlusal adjustment in combination with counselling were by far the most common modes of therapy. More than half of the patients had completed the course of treatment within four visits and only a few patients needed more than ten visits. Eighty one per cent of the patients reported no or only mild symptoms after treatment but in a few cases fairly severe or very severe symptoms persisted. The investigation shows that most patients referred because of mandibular dysfunction can be cured or improved with relatively simple treatment methods and after a few visits. In some cases, however, the patients need more complex and time-consuming treatment.

Neurovascular structures of the mandibular angle and condyle: a comprehensive anatomical review.

PubMed

Yang, Hun-Mu; Won, Sung-Yoon; Kim, Hee-Jin; Hu, Kyung-Seok

2015-11-01

Various surgical interventions including esthetic surgery, salivary gland excision, and open reduction of fracture have been performed in the area around the mandibular angle and condyle. This study aimed to comprehensively review the anatomy of the neurovascular structures on the angle and condyle with recent anatomic and clinical research. We provide detailed information about the branching and distributing patterns of the neurovascular structures at the mandibular angle and condyle, with reported data of measurements and proportions from previous anatomical and clinical research. Our report should serve to help practitioners gain a better understanding of the area in order or reduce potential complications during local procedures. Reckless manipulation during mandibular angle reduction could mutilate arterial branches, not only from the facial artery, but also from the external carotid artery. The transverse facial artery and superficial temporal artery could be damaged during approach and incision in the condylar area. The marginal mandibular branch of the facial nerve can be easily damaged during submandibular gland excision or facial rejuvenation treatment. The main trunk of the facial nerve and its upper and lower distinct divisions have been damaged during parotidectomy, rhytidectomy, and open reductions of condylar fractures. By revisiting the information in the present study, surgeons will be able to more accurately prevent procedure-related complications, such as iatrogenic vascular accidents on the mandibular angle and condyle, complete and partial facial palsy, gustatory sweating (Frey syndrome), and traumatic neuroma after parotidectomy.

Neuromandibular integration in humans and chimpanzees: Implications for dental and mandibular reduction in Homo.

PubMed

Veneziano, Alessio; Meloro, Carlo; Irish, Joel D; Stringer, Chris; Profico, Antonio; De Groote, Isabelle

2018-05-08

Although the evolution of the hominin masticatory apparatus has been linked to diet and food processing, the physical connection between neurocranium and lower jaw suggests a role of encephalization in the trend of dental and mandibular reduction. Here, the hypothesis that tooth size and mandibular robusticity are influenced by morphological changes in the neurocranium was tested. Three-dimensional landmarks, alveolar lengths, and mandibular robusticity data were recorded on a sample of chimpanzee and human skulls. The morphological integration between the neurocranium and the lower jaw was analyzed by means of Singular Warps Analysis. Redundancy Analysis was performed to understand if the pattern of neuromandibular integration affects tooth size and mandibular robusticity. There is significant morphological covariation between neurocranium and lower jaw in both chimpanzees and humans. In humans, changes in the temporal fossa seem to produce alterations of the relative orientation of jaw parts, while the influence of similar neurocranial changes in chimpanzees are more localized. In both species, postcanine alveolar lengths and mandibular robusticity are associated with shape changes of the temporal fossa. The results of this study support the hypothesis that the neurocranium is able to affect the evolution and development of the lower jaw, although most likely through functional integration of mandible, teeth, and muscles within the masticatory apparatus. This study highlights the relative influence of structural constraints and adaptive factors in the evolution of the human skull. © 2018 Wiley Periodicals, Inc.

Genetic integration of molar cusp size variation in baboons

PubMed Central

Koh, Christina; Bates, Elizabeth; Broughton, Elizabeth; Do, Nicholas T.; Fletcher, Zachary; Mahaney, Michael C.; Hlusko, Leslea J.

2010-01-01

Many studies of primate diversity and evolution rely on dental morphology for insight into diet, behavior, and phylogenetic relationships. Consequently, variation in molar cusp size has increasingly become a phenotype of interest. In 2007 we published a quantitative genetic analysis of mandibular molar cusp size variation in baboons. Those results provided more questions than answers, as the pattern of genetic integration did not fit predictions from odontogenesis. To follow up, we expanded our study to include data from the maxillary molar cusps. Here we report on these later analyses, as well as inter-arch comparisons with the mandibular data. We analyzed variation in two-dimensional maxillary molar cusp size using data collected from a captive pedigreed breeding colony of baboons, Papio hamadryas, housed at the Southwest National Primate Research Center. These analyses show that variation in maxillary molar cusp size is heritable and sexually dimorphic. We also estimated additive genetic correlations between cusps on the same crown, homologous cusps along the tooth row, and maxillary and mandibular cusps. The pattern for maxillary molars yields genetic correlations of one between the paracone-metacone and protocone-hypocone. Bivariate analyses of cuspal homologues on adjacent teeth yield correlations that are high or not significantly different from one. Between dental arcades, the non-occluding cusps consistently yield high genetic correlations, especially the metaconid-paracone and metaconid-metacone. This pattern of genetic correlation does not immediately accord with the pattern of development and/or calcification, however these results do follow predictions that can be made from the evolutionary history of the tribosphenic molar. PMID:20034010

Genetic integration of molar cusp size variation in baboons.

PubMed

Koh, Christina; Bates, Elizabeth; Broughton, Elizabeth; Do, Nicholas T; Fletcher, Zachary; Mahaney, Michael C; Hlusko, Leslea J

2010-06-01

Many studies of primate diversity and evolution rely on dental morphology for insight into diet, behavior, and phylogenetic relationships. Consequently, variation in molar cusp size has increasingly become a phenotype of interest. In 2007 we published a quantitative genetic analysis of mandibular molar cusp size variation in baboons. Those results provided more questions than answers, as the pattern of genetic integration did not fit predictions from odontogenesis. To follow up, we expanded our study to include data from the maxillary molar cusps. Here we report on these later analyses, as well as inter-arch comparisons with the mandibular data. We analyzed variation in two-dimensional maxillary molar cusp size using data collected from a captive pedigreed breeding colony of baboons, Papio hamadryas, housed at the Southwest National Primate Research Center. These analyses show that variation in maxillary molar cusp size is heritable and sexually dimorphic. We also estimated additive genetic correlations between cusps on the same crown, homologous cusps along the tooth row, and maxillary and mandibular cusps. The pattern for maxillary molars yields genetic correlations of one between the paracone-metacone and protocone-hypocone. Bivariate analyses of cuspal homologues on adjacent teeth yield correlations that are high or not significantly different from one. Between dental arcades, the nonoccluding cusps consistently yield high genetic correlations, especially the metaconid-paracone and metaconid-metacone. This pattern of genetic correlation does not immediately accord with the pattern of development and/or calcification, however these results do follow predictions that can be made from the evolutionary history of the tribosphenic molar. Copyright 2009 Wiley-Liss, Inc.

Autotransplantation of Mandibular Third Molar with Buccal Cortical Plate to Replace Vertically Fractured Mandibular Second Molar: A Novel Technique.

PubMed

Zufía, Juan; Abella, Francesc; Trebol, Ivan; Gómez-Meda, Ramón

2017-09-01

Tooth replacement often leads to inadequate vertical volume in the recipient site bone when a tooth has been extracted because of a vertical root fracture (VRF). This case report presents the autotransplantation of a mandibular third molar (tooth #32) with the attached buccal cortical plate to replace a mandibular second molar (tooth #31) diagnosed with a VRF. After extraction of tooth #31, the recipient socket was prepared based on the size measured in advance with cone-beam computed tomographic imaging. The precise and calculated osteotomy of the cortical bone of tooth #32 allowed for the exact placement of the donor tooth in the position of tooth #31. The total extraoral time was only 25 minutes. The block was fixed to the recipient socket with an osteosynthesis screw and splinted with a double resin wire for 8 weeks. At the 6-month follow-up, the screw was removed, and the stability of the tooth and the regeneration obtained throughout the vestibular area were confirmed. At the 2-year follow-up, the transplanted tooth was asymptomatic and maintained a normal bone level. Advantages of autotransplantation over dental implants include maintenance of proprioception, possible orthodontic movements, and a relatively low cost. This case report demonstrates that an autotransplantation of a third molar attached to its buccal cortical plate is a viable option to replace teeth with a VRF. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Functional constraints on tooth morphology in carnivorous mammals

PubMed Central

2012-01-01

Background The range of potential morphologies resulting from evolution is limited by complex interacting processes, ranging from development to function. Quantifying these interactions is important for understanding adaptation and convergent evolution. Using three-dimensional reconstructions of carnivoran and dasyuromorph tooth rows, we compared statistical models of the relationship between tooth row shape and the opposing tooth row, a static feature, as well as measures of mandibular motion during chewing (occlusion), which are kinetic features. This is a new approach to quantifying functional integration because we use measures of movement and displacement, such as the amount the mandible translates laterally during occlusion, as opposed to conventional morphological measures, such as mandible length and geometric landmarks. By sampling two distantly related groups of ecologically similar mammals, we study carnivorous mammals in general rather than a specific group of mammals. Results Statistical model comparisons demonstrate that the best performing models always include some measure of mandibular motion, indicating that functional and statistical models of tooth shape as purely a function of the opposing tooth row are too simple and that increased model complexity provides a better understanding of tooth form. The predictors of the best performing models always included the opposing tooth row shape and a relative linear measure of mandibular motion. Conclusions Our results provide quantitative support of long-standing hypotheses of tooth row shape as being influenced by mandibular motion in addition to the opposing tooth row. Additionally, this study illustrates the utility and necessity of including kinetic features in analyses of morphological integration. PMID:22899809

Endosseous titanium implants as anchors for mesiodistal tooth movement in the beagle dog.

PubMed

Saito, S; Sugimoto, N; Morohashi, T; Ozeki, M; Kurabayashi, H; Shimizu, H; Yamasaki, K; Shiba, A; Yamada, S; Shibasaki, Y

2000-12-01

The purpose of this study was to determine the anchorage potential of titanium implants (Branemark; 3.75 x 7 mm) with the use of a sectional arch wire technique for orthodontic mesiodistal tooth movement, as assessed by the osseointegration of implants and tooth movement. Two implants were surgically placed in healed mandibular extraction sites of the second and third premolars on each side in 4 adult male beagle dogs. The implants were surgically uncovered 18 weeks later, and second-stage abutments with soldered edgewise tubes were attached. Segmented edgewise rectangular archwires (0.017 x 0. 025 inch) with a T-loop or an L-loop were placed between the implants and the fourth premolars on both sides as the anchorage unit. One segment in each dog served as a loaded side, and the archwire was calibrated to produce 200 g of lateral force on the fourth premolar. The contralateral segment served as an unloaded side and was not subjected to orthodontic force. Sectional wires were activated biweekly 24, 28, 28, and 32 weeks, respectively, depending on the magnitude and the appearance of mesial tipping movement of the fourth premolar. After mandibular impressions were taken to measure the distance between the first molar and the fourth premolar, the animals were euthanized and dissected mandibles were prepared. The specimens were then embedded in polyester resin and cut to take backscattered electron images. On the basis of these images, the percentage of peri-implant bone volume was calculated and defined as an index of osseointegration. The differences between the initial and final fourth premolar to first molar distances varied (7.40, 8.85, 10.50, and 3.30 mm) on the loaded side, whereas the unloaded side showed no movement. Not only was there no statistical difference in the percent of peri-implant bone volume between the loaded and unloaded sides, but there was also no statistical difference between the compression and tension sides in both loaded and unloaded implants, which suggests that the implants maintained rigid osseointegration. In conclusion, the present study demonstrated that endosseous titanium implants can function as anchors for long-term orthodontic mesiodistal movement.

Management of mandibular fractures in a developing country: a review of 314 cases from two urban centers in Nigeria.

PubMed

Adeyemo, Wasiu L; Iwegbu, Innocent O; Bello, Seidu A; Okoturo, Eyituoyo; Olaitan, Ademola A; Ladeinde, Akinola L; Ogunlewe, Mobolanle O; Adepoju, Adegbenga A; Taiwo, Olanrewaju A

2008-12-01

This study was designed to establish the current demographic and treatment patterns of mandibular fractures in two urban centers (Lagos University Teaching Hospital, Lagos, and National Hospital, Abuja) in Nigeria. All cases of mandibular fractures diagnosed and treated at the Department of Oral and Maxillofacial Surgery, Lagos University Teaching Hospital, Lagos (1998-2007) and Department of Oral and Maxillofacial Surgery, National Hospital, Abuja, Nigeria (2001-2007) were reviewed. Data collected included age, sex, etiology of fracture, anatomic site of fracture, associated maxillofacial fracture, types of treatment, and postoperative complications. The highest incidence of mandibular fractures (49.3%) occurred in the age group 21-30 years and the lowest in the age group 0-10 years, with male preponderance in nearly all age groups. Road traffic crashes (RTC) were the leading cause (67.5%), followed by assault (18.8%), and gunshot. Of the RTC cases, 85 (40%) were sustained from motorcycle-related crashes. The commonest site of fracture was the body of the mandible (n = 137), followed by the angle (n = 114). The majority (83.1%) were treated by closed reduction using intermaxillary fixation, 13.1% by open reduction and internal fixation, and 3.8% had conservative treatment. Mandibular fractures are commonest during the third decade of life and in men, with almost half of the cases due to of road traffic crashes. RTC was the leading cause of mandibular fractures in all age groups. Motorcycle-related mandibular fractures seem to be increasing in Nigeria. There is a need to enforce legislation designed to prevent RTC to reduce maxillofacial fractures in Nigeria.

A novel computer algorithm for modeling and treating mandibular fractures: A pilot study.

PubMed

Rizzi, Christopher J; Ortlip, Timothy; Greywoode, Jewel D; Vakharia, Kavita T; Vakharia, Kalpesh T

2017-02-01

To describe a novel computer algorithm that can model mandibular fracture repair. To evaluate the algorithm as a tool to model mandibular fracture reduction and hardware selection. Retrospective pilot study combined with cross-sectional survey. A computer algorithm utilizing Aquarius Net (TeraRecon, Inc, Foster City, CA) and Adobe Photoshop CS6 (Adobe Systems, Inc, San Jose, CA) was developed to model mandibular fracture repair. Ten different fracture patterns were selected from nine patients who had already undergone mandibular fracture repair. The preoperative computed tomography (CT) images were processed with the computer algorithm to create virtual images that matched the actual postoperative three-dimensional CT images. A survey comparing the true postoperative image with the virtual postoperative images was created and administered to otolaryngology resident and attending physicians. They were asked to rate on a scale from 0 to 10 (0 = completely different; 10 = identical) the similarity between the two images in terms of the fracture reduction and fixation hardware. Ten mandible fracture cases were analyzed and processed. There were 15 survey respondents. The mean score for overall similarity between the images was 8.41 ± 0.91; the mean score for similarity of fracture reduction was 8.61 ± 0.98; and the mean score for hardware appearance was 8.27 ± 0.97. There were no significant differences between attending and resident responses. There were no significant differences based on fracture location. This computer algorithm can accurately model mandibular fracture repair. Images created by the algorithm are highly similar to true postoperative images. The algorithm can potentially assist a surgeon planning mandibular fracture repair. 4. Laryngoscope, 2016 127:331-336, 2017. © 2016 The American Laryngological, Rhinological and Otological Society, Inc.

The variation of cancellous bones at lumbar vertebra, femoral neck, mandibular angle and rib in ovariectomized sheep.

PubMed

Zhang, Yongqiang; Li, Yongfeng; Gao, Qi; Shao, Bo; Xiao, Jianrui; Zhou, Hong; Niu, Qiang; Shen, Mingming; Liu, Baolin; Hu, Kaijin; Kong, Liang

2014-07-01

This study aimed to compare the variation of cancellous bones at four skeletal sites: lumbar vertebra, femoral neck, mandibular angle and rib in ovariectomized sheep. Sixteen adult sheep were randomly divided into two groups: eight sheep were ovariectomized served as experimental group; the other eight untreated sheep were served as control group. Bone mineral density was assessed by dual-energy X-ray absorptiometry on lumbar vertebrae at baseline and twelve months after ovariectomy. After 12 months, lumbar vertebrae L3 and L4, femoral necks, mandibular angles and the fourth ribs were harvested for micro-CT scanning, histological analysis and biomechanical test. The results showed that bone mineral density of lumbar vertebra decreased significantly in twelfth month (p<0.05). The results of micro-CT showed that the bone volume/total volume decreased by 45.6%, 36.1% 21.3% and 18.7% in lumbar vertebrae, femoral necks, mandibular angles and ribs in experimental group (p<0.05) respectively. The trabecular number showed the same downtrend (p<0.05). Histological analysis showed trabecular area/tissue area decreased by 32.1%, 23.2% and 20.7% in lumbar vertebrae, femoral necks and mandibular angles respectively (p<0.05), but no significant difference in ribs. Specimens elastic modulus from lumbar vertebra, femoral neck and mandibular angle were 952±76MPa (628±70MPa), 961±173MPa (610±72MPa) and 595±60MPa (444±31MPa) in control group (experimental group) respectively. These datum indicated that the sensibility of cancellous bones to oestrogen deficiency in ovariectomized sheep was site-specific on a pattern as follows: lumbar vertebra, femoral neck, mandibular angle and rib. Copyright © 2014 Elsevier Ltd. All rights reserved.

Mandibular second molar exhibiting a unique "Y-" and "J-" "shaped" root canal anatomy diagnosed using cone-beam computed tomographic scanning: A case report.

PubMed

Parashar, Saumya-Rajesh; Kowsky, R Dinesh; Natanasabapathy, Velmurugan

2017-01-01

This article aims to report a unique case with aberrant root canal anatomy exhibiting "Y-" and "J"-shaped canal pattern in a mandibular second molar. Anatomic complexities may pose challenges for endodontic treatment. Before performing endodontic treatment, the clinician should be aware of the internal anatomy of the tooth being treated and should recognize anatomic aberrations if present. Presence of unusual anatomy may call for modifications in treatment planning. This report describes in detail about a mandibular second molar tooth associated with two paramolar tubercles having a peculiar "Y-" and "J-"shaped canal anatomy detected with the aid of cone beam computed tomography, which has never been reported in the dental literature. The proposed treatment protocol for the endodontic management of the same has also been discussed.

[Study on accuracy of virtual surgical planning in free fibula mandibular reconstruction by using SurgiCase software].

PubMed

Yan, Guangqi; Wang, Xue; Tan, Xuexin; Wang, Xukai; Yang, Mingliang; Lu, Li

2013-08-01

To evaluate the directional significance of SurgiCase software in free fibula mandibular reconstruction. Between September 2010 and March 2012, 10 patients with mandibular defect underwent free fibula mandibular reconstruction. There were 7 males and 3 females, with an age range of 19-43 years (mean, 27 years). The extent of lesions was 7 cm x 5 cm to 16 cm x 8 cm. In each case, three-dimensional spiral CT scan of the maxilla, mandible, and fibula was obtained before surgery. The CT data were imported into the SurgiCase software and the virtual surgery planning was performed. After that, the mandibular rapid prototyping was made according to customized design. The reconstruction surgery was then carried out using these preoperative data. During actual surgery, the extent of mandibular defect was from 6 cm x 3 cm to 16 cm x 5 cm; the length of fibula which was used to reconstruct mandible was 6-17 cm; and the area of flap was from 6 cm x 5 cm to 16 cm x 6 cm. Preoperative data could not be applied because the intraoperative size of tumor was larger than preoperative design in 1 case of mandibular ameloblastoma, and the fibula was shaped according to the actual osteotomy location; operations were performed successfully according to preoperative design in the other 9 patients. The operation time was 5-7 hours (mean, 6 hours). Primary healing of incision was obtained, without early complications. Ten patients were followed up 1 year. At last follow-up, 8 patients were satisfactory with the appearance and 2 patients complained with unsatisfied wide facial pattern. The panoramic radiograghs showed good bone healing. The range of mouth opening was 2.5-3.5 cm. SurgiCase software can provide precise data for free fibula mandibular reconstruction during surgery. It can be applied widely in clinic.

The Role of Genetic Drift in Shaping Modern Human Cranial Evolution: A Test Using Microevolutionary Modeling

PubMed Central

Smith, Heather F.

2011-01-01

The means by which various microevolutionary processes have acted in the past to produce patterns of cranial variation that characterize modern humans is not thoroughly understood. Applying a microevolutionary framework, within- and among-population variance/covariance (V/CV) structure was compared for several functional and developmental modules of the skull across a worldwide sample of modern humans. V/CV patterns in the basicranium, temporal bone, and face are proportional within and among groups, which is consistent with a hypothesis of neutral evolution; however, mandibular morphology deviated from this pattern. Degree of intergroup similarity in facial, temporal bone, and mandibular morphology is significantly correlated with geographic distance; however, much of the variance remains unexplained. These findings provide insight into the evolutionary history of modern human cranial variation by identifying signatures of genetic drift, gene flow, and migration and set the stage for inferences regarding selective pressures that early humans encountered since their initial migrations around the world. PMID:21461369

An Immunohistochemical Study of Matrix Proteins in the Craniofacial Cartilage in Midterm Human Fetuses

PubMed Central

Shibata, S.; Sakamoto, Y.; Baba, O.; Qin, C.; Murakami, G.; Cho, B.H.

2013-01-01

Immunohistochemical localization of collagen types I, II, and X, aggrecan, versican, dentin matrix protein (DMP)-1, martix extracellular phosphoprotein (MEPE) were performed for Meckel’s cartilage, cranial base cartilage, and mandibular condylar cartilage in human midterm fetuses; staining patterns within the condylar cartilage were compared to those within other cartilaginous structures. Mandibular condylar cartilage contained aggrecan; it also had more type I collagen and a thicker hypertrophic cell layer than the other two types of cartilage; these three characteristics are similar to those of the secondary cartilage of rodents. MEPE immunoreactivity was first evident in the cartilage matrix of all types of cartilage in the human fetuses and in Meckel’s cartilage of mice and rats. MEPE immunoreactivity was enhanced in the deep layer of the hypertrophic cell layer and in the cartilaginous core of the bone trabeculae in the primary spongiosa. These results indicated that MEPE is a component of cartilage matrix and may be involved in cartilage mineralization. DMP-1 immunoreactivity first became evident in human bone lacunae walls and canaliculi; this pattern of expression was comparable to the pattern seen in rodents. In addition, chondroid bone was evident in the mandibular (glenoid) fossa of the temporal bone, and it had aggrecan, collagen types I and X, MEPE, and DMP-1 immunoreactivity; these findings indicated that chondroid bone in this region has phenotypic expression indicative of both hypertrophic chondrocytes and osteocytes. PMID:24441192

[The use of the "cine-technic" in the MRT diagnosis of the temporomandibular joint].

PubMed

Vogl, T J; Eberhard, D; Weigl, P; Assal, J; Randzio, J

1992-03-01

A new cine-technique in a prospective study using rapid gradient echo sequences was evaluated for the MRT investigation of the temporo-mandibular joint. A newly developed hydraulic apparatus was used to produce progressive opening of the jaw and MRT appearances were recorded during predetermined points of mandibular movement. The investigation included 16 normals and 34 patients. A modified gradient echo sequence was combined with an optimised surface coil or a special double coil and this provided good spatial resolution of the articular disc and of the muscular and bony structure. Amongst the abnormal findings were luxation of the disc (15 cases), tears in the disc (5 cases), late effects of internal derangements (12 cases) and condylar hypermotility (7 cases). The new cine-technique provides specific images in any chosen position of the mandible depending on the clinical disability of the patient.

Hard and Soft Tissue Changes Following Maxillary Distraction Osteogenesis and Mandibular Setback with Bilateral Sagittal Split Osteotomy.

PubMed

Bawane, Shilpa S; Andrade, Neelam N

2016-12-01

(1) To highlight the role of intraoral submerged device in distraction osteogenesis (DO) of patients requiring two jaw surgeries for the correction of severe developmental maxillary hypoplasia (MH) and mandibular prognathism (MP) (2) To analyse the hard and soft tissue changes following maxillary DO and mandibular setback with bilateral sagittal split osteotomy (BSSO) in patients with severe MH and MP requiring two jaw surgeries. During the period Jan 2004 to Dec 2006, five patients with severe developmental MH along with MP were treated. In 1st stage maxillary distraction was done. Distraction started on 6th postoperative day, 1 mm distraction was carried out for 10-15 days on either side. Serial radiographs were taken immediate postoperative period for baseline comparison, post-distraction and at the end of distraction. After a period of 3-4 months of distraction 2nd stage was done. In 2nd stage, mandibular setback was done with BSSO and distractors were removed under general anesthesia. Radiographs were taken immediately and at 4 months post-operatively. Cephalometric tracings were carried out preoperatively, post DO and finally after mandibular setback with BSSO. The mean horizontal movement of maxilla was 11.4 mm at ANS and 9.6 mm at A point. Upper incisor edge was advanced by 8.8 mms. SNA increased by 8.4° and SNB decreased by 4.6°. Nasal projection advanced by 4°. Nasolabial angle normalized in all patients, mean change achieved was 10.8°. Upper lip moved forward by 5.4 mm. Lower lip moved backward by 5.4 mm. Mandible positioned backward by 4 mm at B point. No vertical change occurred in the position of A, ANS and upper incisor edges. Mean increase in skeletal angle of convexity was 26.4°. Concave profile was significantly changed to convex in all patients. Maxillary DO and mandibular setback with BSSO was associated with improved facial balance and esthetics.

Bone structure of the temporo-mandibular joint in the individuals aged 18-25.

PubMed

Parafiniuk, M; Gutsch-Trepka, A; Trepka, S; Sycz, K; Wolski, S; Parafiniuk, W

1998-01-01

Osteohistometric studies were performed in 15 female and 15 male cadavers aged 18-25. Condyloid process and right and left acetabulum of the temporo-mandibular joint have been studied. Density has been investigated using monitor screen linked with microscope (magnification 80x). Density in the spongy part of the condyloid process was 26.67-26.77%; in the subchondrial layer--72.13-72.72%, and in the acetabular wall 75.03-75.91%. Microscopic structure of the bones of the temporo-mandibular joint revealed no differences when compared with images of compact and cancellous bone shown in the histology textbooks. Sex and the side of the body had no influence on microscopic image and proportional bone density. Isles of chondrocytes in the trabeculae of the spongy structure of the condyloid process were found in 4 cases and isles of the condensed bone resembling the compact pattern in 7 cases.

[Comparative study of expression of homeobox gene Msx-1, Msx-2 mRNA during the hard tissue formation of mouse tooth development].

PubMed

Wang, Y; Wang, J; Gao, Y

2001-07-01

To observe and compare the expression pattern of Msx-1, Msx-2 mRNA during the different stages of hard tissue formation in the first mandibular molar of mouse and investigate the relationship between the two genes. First mandibular molar germs from 1, 3, 7 and 14-days old mouse were separated and reverse transcription-polymerase chain reaction was performed on the total RNA of them using Msx-1, Msx-2 specific primers separately. Expression of both genes were detected during the different stages of hard tissue formation in the mouse first mandibular molars, but there was some interesting differences in the quantitiy between the two genes. Msx-1 transcripts appeared at the 1 day postnatally, and increase through 3 day, 7 day, then maximally expressed at 14 days postnatally; while Msx-2 mRNA was seen and expressed maximally at the 3 days postnatally, then there was a gradual reduction at 7 days, and 14 days postnatally. The homeobox gene Msx-1, Msx-2 may play a role in the events of the hard tissue formation. The complementary expression pattern of them during the specific stage of hard tissue formation indicates that there may be some functional redundancy between them during the biomineralization.

Evaluation of Buccal Infiltration with Articaine and Inferior Alveolar Nerve Block with Lignocaine for Pulp Therapy in Mandibular Primary Molars.

PubMed

Chopra, Radhika; Marwaha, Mohita; Bansal, Kalpana; Mittal, Meenu

2016-01-01

Failure of inferior alveolar nerve block in achieving profound anesthesia of the pulp due to various reasons has led to the introduction of more potent local anesthetic agents like articaine. This study was conducted to compare the efficacy of buccal infiltration with articaine in achieving pulpal anesthesia of primary molars as compared to inferior alveolar nerve block with lignocaine. 30 patients (4-8 years) with indication of pulp therapy in at least two mandibular primary molars were selected. Patients were randomly assigned to receive nerve block with lignocaine or infiltration with articaine on first appointment and the other solution on second appointment. All the pulpotomies and pulpectomies were performed by a pediatric dentist. Two researchers standing at a distance of 1.5 m recorded the Pain Scores and Sound, Eye, Motor (SEM) scores. After the completion of procedure, the patient was asked to record the Facial Image score and Heft-Parker Visual Analogue Score (HP-VAS). Pain Score recorded at the time of injection showed significantly more movements with block as compared to infiltration (p<0.001). SEM scores at time of pulp extirpation were also higher for block than infiltration (p<0.001). Articaine infiltration has the potential to replace inferior alveolar nerve block for primary mandibular molars.

Soft, hard-tissues and pharyngeal airway volume changes following maxillomandibular transverse osteodistraction: Computed tomography and three-dimensional laser scanner evaluation.

PubMed

Bianchi, Francesca Antonella; Gerbino, Giovanni; Corsico, Marina; Schellino, Eleonora; Barla, Niccolò; Verzè, Laura; Ramieri, Guglielmo

2017-01-01

Maxillomandibular transverse osteodistraction (MMTOD) is an alternative approach to the traditional treatment for transverse maxillary and mandibular deficiencies and crowding. The aim was to report soft and hard-tissues changes and airway volume variation. In this study, skeletally mature, non-syndromic patients with transverse maxillary and mandibular hypoplasia, who underwent a MMTOD between 2010 and 2012, were included. Surgical changes were analysed using clinical evaluation, three-dimensional facial surface data and computed tomography analysis before (T0) and after the completion of post-op orthodontic treatment (T1). Nineteen patients (eight males and eleven females; average age: 26.3 years) were enrolled. MMTOD produces facial changes in the cheek, paranasal areas, nasal base and chin. Facial changes are mostly explained by the underlying skeletal movements, which are essentially represented by the transverse enlargement of both the maxilla and the mandible. Following MMTOD, the airway volume and the lateral dimension of the cross-sectional airway increased significantly. MMTOD is a technique that allows an increase in airway volume and in both maxillary and mandibular arch perimeters simultaneously by increasing skeletal width. Facial appearance is improved and a stable occlusion is obtained. Copyright © 2016 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Orthodontic Intervention to Impacted and Transposed Lower Canines

PubMed Central

Kılıç, Nihat

2017-01-01

Impacted and transposed teeth cause serious difficulties in tooth eruption and movement as well as esthetic and functional outcomes. Proper treatment planning including good biomechanical control is essential in order to avoid side effects during traction and aligning of the impacted and/or transposed teeth. The purpose of the present study was to present a successfully treated female patient having transposed and impacted lower canines by means of a modified lingual arch and fixed orthodontic appliance. A female patient aged 13 years and 9 months presented to the orthodontic department with a chief compliant of bilateral spacing and missing teeth in mandibular dentition. After leveling and creating sufficient space in the mandibular arch for the canines, a modified lingual arch was cemented to the mandibular first molars. The lingual arch had two hooks extending to the distobuccal areas of the canine spaces. Elastic chains were applied between the hooks on the lingual arch and the ligatures tied to the attachments on the canine crowns. The light forces generated by elastic materials caused impacted canines to erupt and tend towards their own spaces in the dental arch. As a result, impacted and transposed lower canines were properly positioned in their spaces, and the treatment results were stable during the retention period. PMID:28540090

A preliminary analysis of correlations between chewing motor patterns and mandibular morphology across mammals.

PubMed

Vinyard, Christopher J; Williams, Susan H; Wall, Christine E; Doherty, Alison H; Crompton, Alfred W; Hylander, William L

2011-08-01

The establishment of a publicly-accessible repository of physiological data on feeding in mammals, the Feeding Experiments End-user Database (FEED), along with improvements in reconstruction of mammalian phylogeny, significantly improves our ability to address long-standing questions about the evolution of mammalian feeding. In this study, we use comparative phylogenetic methods to examine correlations between jaw robusticity and both the relative recruitment and the relative time of peak activity for the superficial masseter, deep masseter, and temporalis muscles across 19 mammalian species from six orders. We find little evidence for a relationship between jaw robusticity and electromyographic (EMG) activity for either the superficial masseter or temporalis muscles across mammals. We hypothesize that future analyses may identify significant associations between these physiological and morphological variables within subgroups of mammals that share similar diets, feeding behaviors, and/or phylogenetic histories. Alternatively, the relative peak recruitment and timing of the balancing-side (i.e., non-chewing-side) deep masseter muscle (BDM) is significantly negatively correlated with the relative area of the mandibular symphysis across our mammalian sample. This relationship exists despite BDM activity being associated with different loading regimes in the symphyses of primates compared to ungulates, suggesting a basic association between magnitude of symphyseal loads and symphyseal area among these mammals. Because our sample primarily represents mammals that use significant transverse movements during chewing, future research should address whether the correlations between BDM activity and symphyseal morphology characterize all mammals or should be restricted to this "transverse chewing" group. Finally, the significant correlations observed in this study suggest that physiological parameters are an integrated and evolving component of feeding across mammals.

Incidence of attachment loss of canines in an overdenture population.

PubMed

Ettinger, Ronald L; Qian, Fang

2014-12-01

Caries and periodontal disease are the most common cause of tooth loss in overdenture populations. Longitudinal data on attachment loss in this population have not been well reported. The purpose of this longitudinal study was to measure periodontal attachment loss in overdenture abutments. In this longitudinal overdenture study, 272 persons fulfilled all of the inclusion criteria. These persons had 662 teeth, 465 (70.2%) of which were canines. This report focused only on participants with canines who returned for 3 consecutive recalls in the 42 months of the study and included 53 persons with 116 canines. During this 42-month period, 6 teeth were extracted. Attachment loss was measured at baseline and at 6 to 18 months, 19 to 30 months, and 31 to 42 months at the mesial, distal, mid-buccal, and mid-lingual surface of each tooth, and was calculated as the combination of pocket probing depth plus height above the gingiva. Attachment loss was compared at each recall. A single examiner made all the measurements. At baseline, the greatest amount of loss was at the mid-buccal surface (5.43 mm), followed by the mid-lingual (4.95 mm), distal (4.41 mm), and mesial (4.35 mm) surfaces. This pattern of attachment loss did not change over the 3 time periods, except that, at the 6 to 18-month recall, the distal measurement was less than at baseline. This decrease could be due to the wear of the abutment or loss of a restoration due to caries. Attachment loss was greater on the mandibular abutments than on the maxillary abutments and could be due to the greater amount of movement of the mandibular overdenture, especially in a buccolingual direction. Attachment loss varied by arch and by site in patients who wore overdentures. Copyright © 2014.

Pilot study on laser propagation in maxillary and mandibular bone: Grey level image analysis for optical measurements.

PubMed

Guiselini, Monalisa Jacob; Deana, Alessandro Melo; de Fátima Teixeira da Silva, Daniela; Koshoji, Nelson Hideyoshi; Mesquita-Ferrari, Raquel Agnelli; do Vale, Katia Llanos; Mascaro, Marcelo Betti; de Moraes, Simone Aleksandra; Bussadori, Sandra Kalil; Fernandes, Kristianne Porta Santos

2017-06-01

Bone tissue anatomy, density and porosity vary among subjects in different phases of life and even within areas of a single specimen. The optical characteristics of changes in bone tissue are analyzed based on these properties. Photobiomodulation has been used to improve bone healing after surgery or fractures. Thus, knowledge on light propagation is of considerable importance to the obtainment of successful clinical outcomes. This study determines light penetration and distribution in human maxillary and mandibular bones in three different regions (anterior, middle, and posterior). A HeNe laser (633nm) irradiated maxillary and mandibular bones in the cervical-apical direction. The light propagation and scattering pattern were acquired and the grey level of the images was analyzed. Three-dimensional plots of the intensity profile and attenuation profiles were created. Differences in optical properties were found between the mandibular and maxillary bones. The maxilla attenuated more light than the mandible at all sites, leading to a shallower penetration depth. Our results provide initial information on the behavior of the propagation of red laser on alveolar bone using an optical method. Copyright © 2017 Elsevier B.V. All rights reserved.

An automatic method for skeletal patterns classification using craniomaxillary variables on a Colombian population.

PubMed

Niño-Sandoval, Tania Camila; Guevara Perez, Sonia V; González, Fabio A; Jaque, Robinson Andrés; Infante-Contreras, Clementina

2016-04-01

The mandibular bone is an important part of the forensic facial reconstruction and it has the possibility of getting lost in skeletonized remains; for this reason, it is necessary to facilitate the identification process simulating the mandibular position only through craniomaxillary measures, for this task, different modeling techniques have been performed, but they only contemplate a straight facial profile that belong to skeletal pattern Class I, but the 24.5% corresponding to the Colombian skeletal patterns Class II and III are not taking into account, besides, craniofacial measures do not follow a parametric trend or a normal distribution. The aim of this study was to employ an automatic non-parametric method as the Support Vector Machines to classify skeletal patterns through craniomaxillary variables, in order to simulate the natural mandibular position on a contemporary Colombian sample. Lateral cephalograms (229) of Colombian young adults of both sexes were collected. Landmark coordinates protocols were used to create craniomaxillary variables. A Support Vector Machine with a linear kernel classifier model was trained on a subset of the available data and evaluated over the remaining samples. The weights of the model were used to select the 10 best variables for classification accuracy. An accuracy of 74.51% was obtained, defined by Pr-A-N, N-Pr-A, A-N-Pr, A-Te-Pr, A-Pr-Rhi, Rhi-A-Pr, Pr-A-Te, Te-Pr-A, Zm-A-Pr and PNS-A-Pr angles. The Class Precision and the Class Recall showed a correct distinction of the Class II from the Class III and vice versa. Support Vector Machines created an important model of classification of skeletal patterns using craniomaxillary variables that are not commonly used in the literature and could be applicable to the 24.5% of the contemporary Colombian sample. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Hydroxyapatite collagen scaffold with autologous bone marrow aspirate for mandibular condylar reconstruction.

PubMed

Howlader, Debraj; Vignesh, U; Bhutia, Dichen P; Pandey, Rahul; Kumar, Sumit; Chandra, Tulika; Mehrotra, Divya

2017-09-01

This study was designed with the aim to assess the efficiency of hydroxyapatite/collagen (HA/Col) bio-scaffold with bone marrow aspirate (BMA) to reconstruct mandibular condyle in patients with temporomandibular joint (TMJ) ankylosis. Seven pediatric patients with TMJ ankylosis, who visited our outpatient clinic and whose parents opted for this procedure, were included in this study. After a history and clinical examination for TMJ movements, computed tomography (CT) scans were obtained. Interposition arthroplasty, with or without coronoidectomy, was performed to gain at least 35 mm of mouth opening. A 2-ml quantity of BMA was aspirated from the posterior iliac crest. A HA/Col block was carved to shape the condyle, and was fixed to the ramus using a plate and screws. A collagen sponge soaked in BMA was interposed in between the graft and ramal end, and the temporal fascia was rotated between the glenoid fossa and graft. Physiotherapy was started on postoperative day 10. All patients were followed up for 1 year. Success was graded on the basis of the mouth opening and TMJ score based on efficiency of chewing, speech, activity, recreation, mood, and anxiety on a five-point ordinal scale. The mean age was 9.71 years (range 5-14 years), and the male-to-female ratio was 5:2. The mean preoperative mouth opening was 4.14 mm, which improved to 34.57 mm at 1-year follow-up. The mean protrusive movement improved from 0 to 2.86 mm. The mean success score was 4.43 out of 5. The mean TMJ score improved from 2.38 to 3.94. A HA/Col bio-scaffold with bone marrow aspirate is a safe and cost-effective alternative for reconstruction of the mandibular condyle, particularly in growing individuals with high osteogenic potential. Copyright © 2017 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Motor behavior during the first chewing cycle in subjects with fixed tooth- or implant-supported prostheses.

PubMed

Grigoriadis, Joannis; Trulsson, Mats; Svensson, Krister G

2016-04-01

Appropriate sensory information from periodontal mechanoreceptors (PMRs) is important for optimizing the positioning of food and adjustment of force vectors during precision biting. This study was designed to describe motor behavior during the first cycle of a natural chewing task and to evaluate the role of such sensory input in this behavior. While 10 subjects with natural dentition, 11 with bimaxillary fixed tooth-supported prostheses (TSP) and 10 with bimaxillary fixed implant-supported prostheses (ISP) (mean age 69 [range 61-83]) chewed a total of five hazelnuts, their vertical and lateral jaw movements were recorded. Data obtained during the first chewing cycle of each hazelnut were analyzed. The amplitude of vertical and lateral mandibular movement and duration of jaw opening did not differ between the groups, indicating similar behavior during this part of the chewing cycle. However, only 30% of the subjects in the natural dentate group, but 82% of those in the TSP and 70% in the ISP group exhibited slippage of the hazelnut during jaw closure in at least one of five trials. The TSP and ISP groups also exhibited more irregular and narrower patterns of motion (total lateral/vertical movement = 0.15 and 0.19, respectively, compared to 0.27 for the natural group). Subjects with fixed tooth- or implant-supported prostheses in both jaws show altered behavior, including inadequate control of the hazelnut, during the first chewing cycle. We propose that these differences are due to impairment or absence of sensory signaling from PMRs in these individuals. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

In vivo bone strain in the mandibular corpus of Sapajus during a range of oral food processing behaviors.

PubMed

Ross, Callum F; Iriarte-Diaz, Jose; Reed, David A; Stewart, Thomas A; Taylor, Andrea B

2016-09-01

It has been hypothesized that mandibular corpus morphology of primates is related to the material properties of the foods that they chew. However, chewing foods with different material properties is accompanied by low levels of variation in mandibular strain patterns in macaques. We hypothesized that if variation in primate mandible form reflects adaptations to feeding on foods with different material and geometric properties, then this variation will be driven primarily by differences in oral food processing behavior rather than differences in chewing per se. To test this hypothesis, we recorded in vivo bone strain data from the lateral and medial surfaces of the mandibular corpus during complete feeding sequences in three adult male Sapajus as they fed on foods with a range of sizes and material properties. We assessed whether variation in mandibular corpus strain regimes is associated with variation in feeding behaviors and/or chewing on different foods, and we quantified the relative variation in mandibular corpus strain regimes associated with chewing on foods of different material properties versus a range of oral food processing behaviors (incisor, premolar, and molar biting; pulling on incisors; mastication). Feeding behavior had a significant effect on mandibular corpus strain regimes, as did chewing side and the cycle number in a feeding sequence. However, food type had weaker effects and usually only through interaction effects with chewing side and/or cycle type. Strain regimes varied most across different chew sides, then across different behaviors, and lastly between mastication cycles on different foods. Strain magnitudes associated with premolar, molar, and incisor biting were larger than those recorded during mastication. These data suggest that intra- and inter-specific variation in mandible morphology is a trade-off between performance requirements of different oral food processing behaviors and of variation in chewing side, with direct effects of food type being less important. Copyright © 2016 Elsevier Ltd. All rights reserved.

The use of three-dimensional imaging to evaluate the effect of conventional orthodontic approach in treating a subject with facial asymmetry

PubMed Central

Kheir, Nadia Abou; Kau, Chung How

2016-01-01

The growth of the craniofacial skeleton takes place from the 3rd week of intra-uterine life until 18 years of age. During this period, the craniofacial complex is affected by extrinsic and intrinsic factors which guide or alter the pattern of growth. Asymmetry can be encountered due to these multifactorial effects or as the normal divergence of the hemifacial counterpart occurs. At present, an orthodontist plays a major role not only in diagnosing dental asymmetry but also facial asymmetry. However, an orthodontist's role in treating or camouflaging the asymmetry can be limited due to the severity. The aim of this research is to report a technique for facial three-dimensional (3D) analysis used to measure the progress of nonsurgical orthodontic treatment approach for a subject with maxillary asymmetry combined with mandibular angular asymmetry. The facial analysis was composed of five parts: Upper face asymmetry analysis, maxillary analysis, maxillary cant analysis, mandibular cant analysis, and mandibular asymmetry analysis which were applied using 3D software InVivoDental 5.2.3 (Anatomage Company, San Jose, CA, USA). The five components of the facial analysis were applied in the initial cone-beam computed tomography (T1) for diagnosis. Maxillary analysis, maxillary cant analysis, and mandibular cant analysis were applied to measure the progress of the orthodontics treatment (T2). Twenty-two linear measurements bilaterally and sixteen angular criteria were used to analyze the facial structures using different anthropometric landmarks. Only angular mandibular asymmetry was reported. However, the subject had maxillary alveolar ridge cant of 9.96°and dental maxillary cant was 2.95° in T1. The mandibular alveolar ridge cant was 7.41° and the mandibular dental cant was 8.39°. Highest decrease in the cant was reported maxillary alveolar ridge around 2.35° and in the mandibular alveolar ridge around 3.96° in T2. Facial 3D analysis is considered a useful adjunct in evaluating inter-arch biomechanics. PMID:27563618

Imaging in traumatic mandibular fractures

PubMed Central

Gemal, Hugo; Reed, Duncan

2017-01-01

A fracture of the mandible is a common trauma presentation amongst young males and represents one of the most frequently encountered fractured bones within the viscerocranium. Historically, assault was the dominant contributing factor but now due to the increased number of vehicles used per capita, motor vehicle accidents are the primary cause. Mandibular fractures can be classified anatomically, by dentition, by muscle group and by severity. The fracture may also be closed, open, comminuted, displaced or pathological. It is important that the imaging modality used identifies the classification as this will decide definitive treatment. X-ray projections have typically been used to detect a mandibular fracture, but are limited to an anteroposterior (AP), lateral and oblique view in an unstable trauma patient. These views are inadequate to detail the level of fracture displacement and show poor detail of the condylar region. Computer tomography (CT) is the imaging modality of choice when assessing a traumatic mandibular injury and can demonstrate a 100% sensitivity in detecting a fracture. This is through use of a multidetector-row CT, which reduces motion blur and therefore produces accurate coronal and sagittal reconstructions. Furthermore, reconstructive three-dimensional CT images gained from planar views, allows a better understanding of the spatial relationship of the fracture with other anatomical landmarks. This ensures a better appreciation of the severity and classification of a mandibular fracture, which therefore influences operative planning. Ultrasound is another useful modality in detecting a mandibular fracture when the patient is too unstable to be transferred to a CT scanner. The sensitivity however is less in comparison to a CT series of images and provides limited detail on the fracture pattern. Magnetic resonance imaging demonstrates use in assessing soft tissue injury of the temporomandibular joint but this is unlikely to be of priority when initially assessing a trauma patient. PMID:28932703

Fracture patterns after bilateral sagittal split osteotomy of the mandibular ramus according to the Obwegeser/Dal Pont and Hunsuck/Epker modifications.

PubMed

Möhlhenrich, Stephan Christian; Kniha, Kristian; Peters, Florian; Ayoub, Nassim; Goloborodko, Evgeny; Hölzle, Frank; Fritz, Ulrike; Modabber, Ali

2017-05-01

The aim of this study was to compare the fracture patterns after sagittal split osteotomy according to Obwegeser/Dal Pont (ODP) and Hunsuck/Epker (HE), as well as to investigate the relationship between lateral bone cut ending or angle and the incidence of unfavorable/bad splits. Postoperative cone-beam computed tomograms of 124 splits according to ODP and 60 according to HE were analyzed. ODP led to 75.8% and HE led to 60% lingual fractures with mandibular foramen contact. Horizontal fractures were found in 9.7% and 6.7%, respectively, and unfavorable/bad splits were found in 11.3% and 10%, respectively. The lateral osteotomy angle was 106.22° (SD 12.03)° for bad splits and 106.6° (SD 13.12)° for favorable splits. Correlations were found between favorable fracture patterns and split modifications and between buccal ending of the lateral bone cut and bad splits (p < 0.001). No relationship was observed between split modifications (p = 0.792) or the osteotomy angle (p = 0.937) and the incidence of unfavorable/bad splits. Split modifications had no influence on the incidence of unfavorable/bad splits, but the buccal ending of the lateral bone cut did have an influence. More lingual fractures with mandibular foramen contact are expected with the ODP modification. The osteotomy angle did not differ between favorable and bad splits. Copyright © 2017 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

[Preliminary study on HA-coated titanium implants used as anchorage for protraction of dog molar teeth].

PubMed

Liang, X; Tang, S; Wang, H

1998-05-01

HA-coated titanium implants were placed surgically into dog mandible to protract the mandibular second molars with an orthodontic force of 150 g. During the force application period of 3 months, the movement of the molars was tested periodically and relevant reasons of movement were analysed. The results showed that the mesial moving distances of the second molar were respectively 1.04 mm, 1.68 mm and 1.76 mm at the first, second and third month, and the main reason of tooth mobility was ascribed to the implant anchorage. It can be concluded tiat HA-coated titanium implant can be used as anchorage for moving and fixing posterior teeth in the orthodontic treatment.

Radiographic assessment of lower third molar eruption in different anteroposterior skeletal patterns and age-related groups.

PubMed

Jakovljevic, Aleksandar; Lazic, Emira; Soldatovic, Ivan; Nedeljkovic, Nenad; Andric, Miroslav

2015-07-01

To analyze radiographic predictors for lower third molar eruption among subjects with different anteroposterior skeletal relations and of different age groups. In total, 300 lower third molars were recorded on diagnostic digital orthopantomograms (DPTs) and lateral cephalograms (LCs). The radiographs were grouped according to sagittal intermaxillary angle (ANB), subject age, and level of lower third molar eruption. The DPT was used to analyze retromolar space, mesiodistal crown width, space/width ratio, third and second molar angulation (α, γ), third molar inclination (β), and gonion angle. The LC was used to determine ANB, angles of maxillar and mandibular prognathism (SNA, SNB), mandibular plane angle (SN/MP), and mandibular lengths. A logistic regression model was created using the statistically significant predictors. The logistic regression analysis revealed a statistically significant impact of β angle and distance between gonion and gnathion (Go-Gn) on the level of lower third molar eruption (P < .001 and P < .015, respectively). The retromolar space was significantly increased in the adult subgroup for all skeletal classes. The lower third molar impaction rate was significantly higher in the adult subgroup with the Class II (62.3%) compared with Class III subjects (31.7%; P < .013). The most favorable values of linear and angular predictors of mandibular third molar eruption were measured in Class III subjects. For valid estimation of mandibular third molar eruption, certain linear and angular measures (β angle, Go-Gn), as well as the size of the retromolar space, need to be considered.

Mandibular asymmetry and the fourth dimension.

PubMed

Kaban, Leonard B

2009-03-01

This paper represents more than 30 years of discussion and collaboration with Drs Joseph Murray and John Mulliken in an attempt to understand growth patterns over time (ie, fourth dimension) in patients with hemifacial microsomia (HFM). This is essential for the development of rational treatment protocols for children and adults with jaw asymmetry. Traditionally, HFM was thought of as a unilateral deformity, but it was recognized that 20% to 30% of patients had bilateral abnormalities. However, early descriptions of skeletal correction addressed almost exclusively lengthening of the short (affected) side of the face. Based on longitudinal clinical observations of unoperated HFM patients, we hypothesized that abnormal mandibular growth is the earliest skeletal manifestation and that restricted growth of the mandible plays a pivotal role in progressive distortion of both the ipsilateral and contralateral facial skeleton. This hypothesis explains the progressive nature of the asymmetry in patients with HFM and provides the rationale for surgical lengthening of the mandible in children to prevent end-stage deformity. During the past 30 years, we have learned that this phenomenon of progressive distortion of the adjacent and contralateral facial skeleton occurs with other asymmetric mandibular undergrowth (tumor resection, radiation therapy, or posttraumatic defects) and overgrowth (mandibular condylar hyperplasia) conditions. In this paper, I describe the progression of deformity with time in patients with mandibular asymmetry as a result of undergrowth and overgrowth. Understanding these concepts is critical for the development of rational treatment protocols for adults with end-stage asymmetry and for children to minimize secondary deformity.

The CHARGE association: report of two cases.

PubMed

Venetikidou, A

1993-01-01

Although many reports of the CHARGE association appear in the literature, the dental findings were never discussed before. In this report of two cases, both patients present with delayed eruption of the permanent teeth and a remarkable similarity of the eruption pattern of the mandibular teeth. One lower permanent central incisor is congenitally missing, while the other is malformed. The lower permanent laterals of JM have erupted lingually and interfere with his speech and function of the tongue. Mandibular retrognathism is present. TM had a V-shaped constricted upper arch, which was expanded in a first phase of orthodontic intervention. Fixed appliances are the future considerations for the correction of the malocclusion.

A comparison of skeletal stability after mandibular advancement and use of two rigid internal fixation techniques.

PubMed

Blomqvist, J E; Ahlborg, G; Isaksson, S; Svartz, K

1997-06-01

Two different methods of rigid fixation were compared for postoperative stability 6 months after mandibular advancement for treatment of Class II malocclusion. Sixty (30 + 30) patients from two different oral and maxillofacial units treated for a Class II malocclusion by bilateral saggital split osteotomy (BSSO), and two different methods of internal rigid fixation were prospectively investigated. Two groups (S1, n = 15; S2, n = 15) had bicortical noncompressive screws inserted in the gonial area through a transcutaneous approach, and the other two groups (P1, n = 15; P2, n = 15) had the bone segments fixed with unicortical screws and miniplates on the lateral surface of the mandibular body. Cephalograms were taken preoperatively, 2 days postoperatively and 6 months after the operation. A computer program was used to superimpose the three cephalograms and to register the mandibular advancement and postoperative change both sagittally and vertically. These were minor differences in the advancement and postoperative changes between the four groups, but statistically no significant difference was shown in either sagittal or vertical directions. However, statistically verified differences proved that increasing age was associated with a smaller amount of postsurgical relapse. Low-angle cases (ML/NSL < 25 degrees) had a bigger amount of surgical (P = .0008) and postsurgical (P = .0195) movement compared with the patients in the high-angle group (ML/NSL < 38 degrees). Using a multiple regression test, a positive correlation was also shown between the amount of surgical advancement and the amount of postsurgical instability (P = .018). This prospective dual-center study indicates that the two different methods of internal rigid fixation after surgical advancement of the mandible by BSSO did not significantly differ from each other, and it is up to the individual operator to choose the method for internal rigid fixation.

Mandibular pseudocarcinomatous hyperplasia.

PubMed

Warter, A; Walter, P; Meyer, C; Barrière, P; Galatir, L; Wilk, A

2000-08-01

Three unusual cases of pseudocarcinomatous (pseudoepitheliomatous) hyperplasia (PH) affecting chronic osteomyelitic mandibular sequestra are reported to highlight the differences with the various squamous neoplasms which occur in that site. In two patients carrying a mandibular graft following the excision of an ameloblastoma, mucosal ulcers resulted in chronic osteomyelitis. In a third patient, an apical dental infection was associated with fistulated osteomyelitis. Histology of the three sequestra showed an intraosseous squamous proliferation. It was characterized by a peripheral involvement of medullary spaces, the more mature epithelial layer covering the bone trabeculae without intervening stroma, and the basal type epithelial layer surrounding a central fibrovascular core. There were no histological or cytological signs of malignancy. PH shows an inverted pattern when compared with the centro-medullary tumoural islands seen in the various oral or odontogenic squamous neoplasms which occur in the jaws. The lack of signs of malignancy distinguish PH from common squamous cell carcinomas. A short clinical course is an important feature in the distinction of PH from the well differentiated squamous cell carcinomas which may develop in fistulated chronic osteomyelitis.

Relationship between masticatory performance using a gummy jelly and masticatory movement.

PubMed

Uesugi, Hanako; Shiga, Hiroshi

2017-10-01

The purpose of this study was to clarify the relationship between masticatory performance using a gummy jelly and masticatory movement. Thirty healthy males were asked to chew a gummy jelly on their habitual chewing side for 20s, and the parameters of masticatory performance and masticatory movement were calculated as follows. For evaluating the masticatory performance, the amount of glucose extraction during chewing of a gummy jelly was measured. For evaluating the masticatory movement, the movement of the mandibular incisal point was recorded using the MKG K6-I, and ten parameters of the movement path (opening distance and masticatory width), movement rhythm (opening time, closing time, occluding time, and cycle time), stability of movement (stability of path and stability of rhythm), and movement velocity (opening maximum velocity and closing maximum velocity) were calculated from 10 cycles of chewing beginning with the fifth cycle. The relationship between the amount of glucose extraction and parameters representing masticatory movement was investigated and then stepwise multiple linear regression analysis was performed. The amount of glucose extraction was associated with 7 parameters representing the masticatory movement. Stepwise multiple linear regression analysis showed that the opening distance, closing time, stability of rhythm, and closing maximum velocity were the most important factors affecting the glucose extraction. From these results it was suggested that there was a close relation between masticatory performance and masticatory movement, and that the masticatory performance could be increased by rhythmic, rapid and stable mastication with a large opening distance. Copyright © 2017 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Evaluation of total alloplastic temporo-mandibular joint replacement with two different types of prostheses: A three-year prospective study

PubMed Central

Gonzalez-Perez-Somarriba, Borja; Centeno, Gabriel; Vallellano, Carpóforo; Montes-Carmona, Jose-Francisco

2016-01-01

Background Temporo-Mandibular Joint (TMJ) replacement has been used clinically for years. The objective of this study was to evaluate outcomes achieved in patients with two different categories of TMJ prostheses. Material and Methods All patients who had a TMJ replacement (TMJR) implanted during the study period from 2006 through 2012 were included in this 3-year prospective study. All procedures were performed using the Biomet Microfixation TMJ Replacement System, and all involved replacing both the skull base component (glenoid fossa) and the mandibular condyle. Results Fifty-seven patients (38 females and 19 males), involving 75 TMJs with severe disease requiring reconstruction (39 unilateral, 18 bilateral) were operated on consecutively, and 68 stock prostheses and 7 custom-made prostheses were implanted. The mean age at surgery was 52.6±11.5 years in the stock group and 51.8±11.7 years in the custom-made group. In the stock group, after three years of TMJR, results showed a reduction in pain intensity from 6.4±1.4 to 1.6±1.2 (p<0.001), and an improvement in jaw opening from 2.7±0.9 cm to 4.2±0.7 cm (p<0.001). In the custom-made group, after three years of TMJR, results showed a reduction in pain intensity from 6.0±1.6 to 2.2±0.4 (p<0.001), and an improvement in jaw opening from 1.5±0.5 cm to 4.3±0.6 cm (p<0.001). No statistically significant differences between two groups were detected. Conclusions The results of this three-year prospective study support the surgical placement of TMJ prostheses (stock prosthetic, and custom-made systems), and show that the approach is efficacious and safe, reduces pain, and improves maximum mouth opening movement, with few complications. As such, TMJR represents a viable technique and a stable long-term solution for cranio-mandibular reconstruction in patients with irreversible end-stage TMJ disease. Comparing stock and custom-made groups, no statistically significant differences were detected with respect to pain intensity reduction and maximum mouth opening improvement. Key words:Temporo-mandibular joint, temporo-mandibular joint replacement, prosthesis, biomaterials, biomedical engineering, computer-aided design and manufacturing. PMID:27475697

Mandibular fractures in children: analysis of 61 cases and review of the literature.

PubMed

Glazer, Michael; Joshua, Ben Zion; Woldenberg, Yitzhak; Bodner, Lipa

2011-01-01

The purpose was to evaluate the incidence, etiology, site and patterns, management and treatment methods, and outcome of pediatric patients with mandibular fractures. Pediatric patients (1.5-16 years old) with mandibular fractures, treated at the Soroka University Medical Center were included in the study. Age, gender, etiology, site and type of fracture, associated injuries, mode of treatment, outcome, complications, and follow up were evaluated. The cases were divided into 3 age groups: Group A: 1.5-5 years, Group B: 6-11 years, and Group C: 12-16 years. Sixty one patients were included in the study. The male to female ratio was 2:1. Motor vehicle accident was the most common cause. Associated trauma was more common in young children. The condyle was involved in 54% of the fractures. Closed reduction and intermaxillary fixation was the most common treatment used. Complications were rare. Management of mandibular fracture in the pediatric age group is a challenge. The anatomical complexity of the developing mandible and teeth strongly suggest the use of surgical techniques that are different from those routinely used in adults. The conservative approach is recommended. Whenever possible closed reduction should be the treatment of choice. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Event-Related Beta EEG Changes During Active, Passive Movement and Functional Electrical Stimulation of the Lower Limb.

PubMed

Qiu, Shuang; Yi, Weibo; Xu, Jiapeng; Qi, Hongzhi; Du, Jingang; Wang, Chunfang; He, Feng; Ming, Dong

2016-02-01

A number of electroencephalographic (EEG) studies have reported on event-related desynchronization/synchronization (ERD/ERS) during active movements, passive movements, and the movements induced by functional electrical stimulation (FES). However, the quantitative differences in ERD values and affected frequency bands associated with the lower limb have not been discussed. The goal of this paper was to quantitatively compare the ERD patterns during active movement, passive movement and FES-induced movement of the lower limb. 64-channel EEG signals were recorded to investigate the brain oscillatory patterns during active movement, passive movement and FES-induced movement of the lower limb in twelve healthy subjects. And passive movement and FES-induced movement were also performed in a hemiplegic stroke patient. For healthy subjects, FES-induced movement presented significantly higher characteristic frequency of central beta ERD while there was no significant difference in ERD values compared with active or passive movement. Meanwhile, beta ERD values of FES-induced movement were significantly correlated with those of active movement, and spatial distribution of beta ERD pattern for FES-induced movement was more correlated with that for active movement. In addition, the stroke patient presented central ERD patterns during FES-induced movement, while no ERD with similar frequencies could be found during passive movement. This work implies that the EEG oscillatory pattern under FES-induced movement tends more towards active movement instead of passive movement. The quantification of ERD patterns could be expected as a potential technique to evaluate the brain response during FES-induced movement.

A morphological novelty for feeding and sound production in the yellowtail clownfish.

PubMed

Olivier, Damien; Frédérich, Bruno; Herrel, Anthony; Parmentier, Eric

2015-04-01

The yellowtail clownfish Amphiprion clarkii is able to close its mouth very quickly by means of the cerato-mandibular (c-md) ligament, a synapomorphic trait of Pomacentridae joining the hyoid bar to the medial part of the lower jaw. This fast closure induces tooth collision, thus producing sounds that the clownfish uses during agonistic behaviors. To investigate whether this rapid jaw movement is also used during feeding, we analyzed the kinematics of sound production and feeding. Sound production, feeding on live planktonic prey, and feeding on food attached to tweezers was filmed with a high-speed camera. Three kinds of kinematic patterns were detected and were associated with the two different types of food presented: one performed to catch planktonic prey (PP), and two (called B-1 and B-2) to bite attached food items. The kinematic pattern of B-2 is similar to that observed during sound production (SP) and the transection of the c-md ligament highlights that sound production and biting-2 motions are dependent on this morphological trait. Our data show that the c-md ligament in addition to its role in sound production allows duplication of the mouth-closing mechanism during feeding. This highlights the key role played by the c-md ligament in sound production and feeding on attached prey. J. Exp. Zool. 323A: 227-238, 2015. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

Dental and skeletal components of Class II open bite treatment with a modified Thurow appliance

PubMed Central

Jacob, Helder Baldi; dos Santos-Pinto, Ary; Buschang, Peter H.

2014-01-01

Introduction Due to the lack of studies that distinguish between dentoalveolar and basal changes caused by the Thurow appliance, this clinical study, carried out by the School of Dentistry - State University of São Paulo/Araraquara, aimed at assessing the dental and skeletal changes induced by modified Thurow appliance. Methods The sample included an experimental group comprising 13 subjects aged between 7 and 10 years old, with Class II malocclusion and anterior open bite, and a control group comprising 22 subjects similar in age, sex and mandibular plane angle. Maxillary/mandibular, horizontal/vertical, dental/skeletal movements (ANS, PNS, U1, U6, Co, Go, Pog, L1, L6) were assessed, based on 14 landmarks, 8 angles (S-N-ANS, SNA, PPA, S-N-Pog, SNB, MPA, PP/MPA, ANB) and 3 linear measures (N-Me, ANS-Me, S-Go). Results Treatment caused significantly greater angle decrease between the palatal and the mandibular plane of the experimental group, primarily due to an increase in the palatal plane angle. ANB, SNA and S-N-ANS angles significantly decreased more in patients from the experimental group. PNS was superiorly remodeled. Lower face height (ANS-Me) decreased in the experimental group and increased in the control group. Conclusions The modified Thurow appliance controlled vertical and horizontal displacements of the maxilla, rotated the maxilla and improved open bite malocclusion, decreasing lower facial height. PMID:24713556

Modifying patterns of movement in people with low back pain -does it help? A systematic review.

PubMed

Laird, Robert A; Kent, Peter; Keating, Jennifer L

2012-09-07

Physiotherapy for people with low back pain frequently includes assessment and modification of lumbo-pelvic movement. Interventions commonly aim to restore normal movement and thereby reduce pain and improve activity limitation. The objective of this systematic review was to investigate: (i) the effect of movement-based interventions on movement patterns (muscle activation, lumbo-pelvic kinematics or postural patterns) of people with low back pain (LBP), and (ii) the relationship between changes in movement patterns and subsequent changes in pain and activity limitation. MEDLINE, Cochrane Central, EMBASE, AMI, CINAHL, Scopus, AMED, ISI Web of Science were searched from inception until January 2012. Randomised controlled trials or controlled clinical trials of people with LBP were eligible for inclusion. The intervention must have been designed to influence (i) muscle activity patterns, (ii) lumbo-pelvic kinematic patterns or (iii) postural patterns, and included measurement of such deficits before and after treatment, to allow determination of the success of the intervention on the lumbo-pelvic movement. Twelve trials (25% of retrieved studies) met the inclusion criteria. Two reviewers independently identified, assessed and extracted data. The PEDro scale was used to assess method quality. Intervention effects were described using standardised differences between group means and 95% confidence intervals. The included trials showed inconsistent, mostly small to moderate intervention effects on targeted movement patterns. There was considerable heterogeneity in trial design, intervention type and outcome measures. A relationship between changes to movement patterns and improvements in pain or activity limitation was observed in one of six studies on muscle activation patterns, one of four studies that examined the flexion relaxation response pattern and in two of three studies that assessed lumbo-pelvic kinematics or postural characteristics. Movement-based interventions were infrequently effective for changing observable movement patterns. A relationship between changes in movement patterns and improvement in pain or activity limitation was also infrequently observed. No independent studies confirm any observed relationships. Challenges for future research include defining best methods for measuring (i) movement aberrations, (ii) improvements in movements, and (iii) the relationship between changes in how people move and associated changes in other health indicators such as activity limitation.

Three-dimensional finite element analysis of the stress distribution pattern in a mandibular first molar tooth restored with five different restorative materials.

PubMed

D'souza, Kathleen Manuela; Aras, Meena Ajay

2017-01-01

Badly broken or structurally compromised posterior teeth are frequently associated with crown/root fracture. Numerous restorative materials have been used to fabricate indirect full-coverage restorations for such teeth. This study aims to evaluate and compare the effect of restorative materials on the stress distribution pattern in a mandibular first molar tooth, under varying loading conditions and to compare the stress distribution pattern in five commonly used indirect restorative materials. Five three-dimensional finite element models representing a mandibular first molar tooth restored with crowns of gold, porcelain fused to metal, composite (Artglass), alumina-based zirconia (In-Ceram Zirconia [ICZ]), and double-layered zirconia-based materials (zirconia core veneered with porcelain, Lava) were constructed, using a Finite Element Analysis Software (ANSYS version 10; ANSYS Inc., Canonsburg, PA, USA). Two loading conditions were applied, simulating maximum bite force of 600 N axially and normal masticatory bite force of 225 N axially and nonaxially. Both all-ceramic crowns allowed the least amount of stress distribution to the surrounding tooth structure. In maximum bite force-simulation test, alumina-based all-ceramic crown displayed the highest von Mises stresses (123.745 MPa). In the masticatory bite force-simulation test, both all-ceramic crowns (122.503-133.13 MPa) displayed the highest von Mises stresses. ICZ crown displayed the highest peak von Mises stress values under maximum and masticatory bite forces. ICZ and Lava crowns also allowed the least amount of stress distribution to the surrounding tooth structure, which is indicative of a favorable response of the underlying tooth structure to the overlying full-coverage indirect restorative material. These results suggest that ICZ and Lava crowns can be recommended for clinical use in cases of badly damaged teeth.

Patterns of mandible fracture in children under 12 years in a district trauma center in India.

PubMed

Namdev, Ritu; Jindal, Ayushi; Bhargava, Smriti; Dutta, Samir; Singhal, Parul; Grewal, Priyanka

2016-02-01

This study aims to present the data of mandibular fracture among children in the age group of 0-12 years treated in a district trauma center in India. Sixty-two children younger than 12 years treated for mandibular fractures over two-and-a-half-year period were studied by age, gender, anatomic site, etiology, socioeconomic status, residing area, interval from trauma to reporting, and treatment performed. The cases were divided into three age groups, and the records of the patients were analyzed. The male to female ratio was 1.58:1. Common fall and fall from bike together was a cause for injury in 50% (31 patients), of total patients. Condylar fractures occurred in 25 patients (40.3%). Multiple fractures were seen in 13% of the patients. In 47 (75.8%) patients, associated injuries other than the mandibular fractures were also present. Most patients with mandibular fractures were treated by closed reduction (36 patients, 58%). Conservative treatment and open reduction were done in 18 (29%) and 8 (13%) patients, respectively. In addition to factors such as age, gender, etiology, anatomic site, and treatment of mandibular fracture, this study also reported statistics regarding other factors such as residing area, socioeconomic status, and interval from trauma to reporting in Indian patients. It is hoped that the data presented here will be valuable to the government agencies and healthcare professionals for planning treatment, recommending preventive measures and encouraging research in this area. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Accuracy of Dolphin visual treatment objective (VTO) prediction software on class III patients treated with maxillary advancement and mandibular setback.

PubMed

Peterman, Robert J; Jiang, Shuying; Johe, Rene; Mukherjee, Padma M

2016-12-01

Dolphin® visual treatment objective (VTO) prediction software is routinely utilized by orthodontists during the treatment planning of orthognathic cases to help predict post-surgical soft tissue changes. Although surgical soft tissue prediction is considered to be a vital tool, its accuracy is not well understood in tow-jaw surgical procedures. The objective of this study was to quantify the accuracy of Dolphin Imaging's VTO soft tissue prediction software on class III patients treated with maxillary advancement and mandibular setback and to validate the efficacy of the software in such complex cases. This retrospective study analyzed the records of 14 patients treated with comprehensive orthodontics in conjunction with two-jaw orthognathic surgery. Pre- and post-treatment radiographs were traced and superimposed to determine the actual skeletal movements achieved in surgery. This information was then used to simulate surgery in the software and generate a final soft tissue patient profile prediction. Prediction images were then compared to the actual post-treatment profile photos to determine differences. Dolphin Imaging's software was determined to be accurate within an error range of +/- 2 mm in the X-axis at most landmarks. The lower lip predictions were most inaccurate. Clinically, the observed error suggests that the VTO may be used for demonstration and communication with a patient or consulting practitioner. However, Dolphin should not be useful for precise treatment planning of surgical movements. This program should be used with caution to prevent unrealistic patient expectations and dissatisfaction.

An equilibrium-point model of electromyographic patterns during single-joint movements based on experimentally reconstructed control signals.

PubMed

Latash, M L; Goodman, S R

1994-01-01

The purpose of this work has been to develop a model of electromyographic (EMG) patterns during single-joint movements based on a version of the equilibrium-point hypothesis, a method for experimental reconstruction of the joint compliant characteristics, the dual-strategy hypothesis, and a kinematic model of movement trajectory. EMG patterns are considered emergent properties of hypothetical control patterns that are equally affected by the control signals and peripheral feedback reflecting actual movement trajectory. A computer model generated the EMG patterns based on simulated movement kinematics and hypothetical control signals derived from the reconstructed joint compliant characteristics. The model predictions have been compared to published recordings of movement kinematics and EMG patterns in a variety of movement conditions, including movements over different distances, at different speeds, against different-known inertial loads, and in conditions of possible unexpected decrease in the inertial load. Changes in task parameters within the model led to simulated EMG patterns qualitatively similar to the experimentally recorded EMG patterns. The model's predictive power compares it favourably to the existing models of the EMG patterns. Copyright © 1994. Published by Elsevier Ltd.

Distance of the contact glide in the closing masticatory stroke during mastication of three types of food.

PubMed

Rilo, B; Fernández-Formoso, N; Mora, M J; Cadarso-Suárez, C; Santana, U

2009-08-01

This study was designed to characterize the distance of the contact glide in the closing masticatory stroke in healthy adult subjects, during chewing of three types of food (crustless bread, chewing gum and peanuts). Mandibular movements (masticatory movements and laterality movements with dental contact) were registered using a gnathograph (MK-6I Diagnostic System) on the right and left side during unilateral chewing of the three food types. Length of dental contact was measured in masticatory cycle, which is defined as where the terminal part of the chewing cycles could be superimposed on the pathways taken by the mandible during lateral excursions with occlusal contacts. The length of dental contact during mastication of chewing gum is 1.46 +/- 1 mm, during chewing of soft bread is 1.38 +/- 0.7 mm and during chewing of peanuts is 1.45 +/- 0.9 mm. There is no significant difference in the lengths of dental contact during mastication of three types of foods that enable direct tooth gliding.

Negative Influence of Motor Impairments on Upper Limb Movement Patterns in Children with Unilateral Cerebral Palsy. A Statistical Parametric Mapping Study

PubMed Central

Simon-Martinez, Cristina; Jaspers, Ellen; Mailleux, Lisa; Desloovere, Kaat; Vanrenterghem, Jos; Ortibus, Els; Molenaers, Guy; Feys, Hilde; Klingels, Katrijn

2017-01-01

Upper limb three-dimensional movement analysis (UL-3DMA) offers a reliable and valid tool to evaluate movement patterns in children with unilateral cerebral palsy (uCP). However, it remains unknown to what extent the underlying motor impairments explain deviant movement patterns. Such understanding is key to develop efficient rehabilitation programs. Although UL-3DMA has been shown to be a useful tool to assess movement patterns, it results in a multitude of data, challenging the clinical interpretation and consequently its implementation. UL-3DMA reports are often reduced to summary metrics, such as average or peak values per joint. However, these metrics do not take into account the continuous nature of the data or the interdependency between UL joints, and do not provide phase-specific information of the movement pattern. Moreover, summary metrics may not be sensitive enough to estimate the impact of motor impairments. Recently, Statistical Parametric Mapping (SPM) was proposed to overcome these problems. We collected UL-3DMA of 60 children with uCP and 60 typically developing children during eight functional tasks and evaluated the impact of spasticity and muscle weakness on UL movement patterns. SPM vector field analysis was used to analyze movement patterns at the level of five joints (wrist, elbow, shoulder, scapula, and trunk). Children with uCP showed deviant movement patterns in all joints during a large percentage of the movement cycle. Spasticity and muscle weakness negatively impacted on UL movement patterns during all tasks, which resulted in increased wrist flexion, elbow pronation and flexion, increased shoulder external rotation, decreased shoulder elevation with a preference for movement in the frontal plane and increased trunk internal rotation. Scapular position was altered during movement initiation, although scapular movements were not affected by muscle weakness or spasticity. In conclusion, we identified pathological movement patterns in children with uCP and additionally mapped the negative impact of spasticity and muscle weakness on these movement patterns, providing useful insights that will contribute to treatment planning. Last, we also identified a subset of the most relevant tasks for studying UL movements in children with uCP, which will facilitate the interpretation of UL-3DMA data and undoubtedly contribute to its clinical implementation. PMID:29051729

Performance of Remotely Controlled Mandibular Protrusion Sleep Studies for Prediction of Oral Appliance Treatment Response

PubMed Central

Sutherland, Kate; Ngiam, Joachim; Cistulli, Peter A.

2017-01-01

Study Objectives: Mandibular protrusion during sleep monitoring has been proposed as a method to predict oral appliance treatment outcome. A commercial remotely controlled mandibular protrusion (RCMP) device has become available for this purpose with predictive accuracy demonstrated in an initial study. Our aim was to validate this RCMP method for oral appliance treatment outcome prediction in a clinical sleep laboratory setting. Methods: Forty-two obstructive sleep apnea (OSA) patients (apnea-hypopnea index [AHI] > 10 events/h) were recruited to undergo a RCMP sleep study before commencing oral appliance treatment. The RCMP study was used to make a prediction of treatment “Success” or “Failure” based on a rule of ≤ 1 respiratory event per 5 min supine rapid eye movement sleep. Oral appliance treatment response was verified by polysomonography and defined as treatment AHI < 10 events/h with 50% reduction. Results: Participants were on average middle-aged (57.1 ± 11.6 y) and overweight (29.6 ± 4.5 kg/m2) with baseline AHI 31.5 ± 20.5 events/h, 39% severe OSA (AHI > 30 events/h). Two participants (5%) were not able to tolerate the RCMP study. Oral appliance treatment outcome was verified in 33 participants (RCMP results: “Success” n = 10, “Failure” n = 15, “Inconclusive” n = 8). In those with a treatment outcome prediction (n = 25) the diagnostic characteristics of the RCMP test were sensitivity 81.8%, specificity 92.9%, positive predictive value 90%, and negative predictive value 86.7% (n = 3 misclassified). Conclusions: The RCMP device was well tolerated by patients and successfully used to perform mandibular protrusion sleep studies in our sleep laboratory. The RCMP sleep study showed good accuracy as a prediction technique for oral appliance treatment outcome, although there was a high rate of inconclusive tests. Citation: Sutherland K, Ngiam J, Cistulli PA. Performance of remotely controlled mandibular protrusion sleep studies for prediction of oral appliance treatment response. J Clin Sleep Med. 2017;13(3):411–417. PMID:27923436

Comparison of treatments with the Forsus fatigue resistant device in relation to skeletal maturity: a cephalometric and magnetic resonance imaging study.

PubMed

Aras, Aynur; Ada, Emel; Saracoğlu, Hatice; Gezer, Naciye S; Aras, Isil

2011-11-01

The aim of this study was to compare the dentoskeletal changes and alterations of mandibular condyle-disc-fossa relationships in subjects at the peak and the end of the pubertal growth period treated with the Forsus fatigue resistant device (3M Unitek, Monrovia, Calif). The sample consisted of 29 subjects with Class II Division 1 malocclusions who were classified according to their hand-wrist radiographs. Fifteen patients were at or just before the peak phase of pubertal growth (peak pubertal group). Fourteen patients were near the end of the pubertal growth period (late pubertal group). The study was conducted by using lateral cephalometric radiographs and magnetic resonance images obtained at the beginning and at the end of the application of the Forsus fatigue resistant device. The treatment period was 9 months. The Wilcoxon signed rank test was used to evaluate differences within groups. The changes observed in both groups were compared by using the Mann-Whitney U test. There were statistically significant group differences in mandibular length and ramus length, with significant increases of these parameters in the peak pubertal group (P <0.05). No significant differences were observed between the groups concerning dental parameters (P >0.05), with the exception of mandibular molar vertical movements, which were significantly greater in the peak pubertal group (P <0.05). Analysis of the magnetic resonance images showed no positional changes of the mandibular condyle in relation to the glenoid fossa in either group (P >0.05). Although the articular disc was positioned more anteriorly in the peak pubertal group compared with its pretreatment position (P <0.05), the position of the disc was still within the physiologic range. No significant intergroup difference was observed for disc-condyle relationship (P >0.05). The Forsus fatigue resistant device did not appear to cause significant increases in mandibular dimensions in subjects in late puberty. According to the magnetic resonance image findings, Forsus treatment is not a risk factor for the development of temporomandibular dysfunction in subjects with no signs and clinical symptoms of dysfunction. Copyright © 2011 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

The effectiveness of adhesives on the retention of mandibular free end saddle partial dentures: An in vitro study.

PubMed

Quiney, Daniel; Nishio Ayre, Wayne; Milward, Paul

2017-07-01

Existing in vitro methods for testing denture adhesives do not fully replicate the complex oral geometries and environment; and in vivo methods are qualitative, prone to bias and not easily reproducible. The purpose of this study was to develop a novel, quantitative and more accurate model to test the effect of adhesives on the retentive force of mandibular free end saddle partial dentures. An in vitro model was developed based on an anatomically accurate cast of a clinical case. Experimentally, the amount of adhesive was varied (0.2g-1g) and the tensile force required for displacement was measured. Different commercially available adhesives were then tested at the optimum volume using the in vitro model. A 3D finite element model of the denture was used to assess how the forces to induce denture displacement varied according to the position of the force along the saddle length. The mass of adhesive was found to significantly alter retention forces, with 0.4-0.7g being the optimum range for this particular scenario. Use of adhesives significantly improved mandibular free end saddle partial denture retention with the worst performing adhesive increasing retention nine-fold whilst the best performing adhesive increased retention twenty three-fold. The finite element model revealed that 77% more force was required to displace the denture by positioning forces towards the mesial end of the saddle compared to the distal end. An in vitro denture adhesive model was developed, which demonstrated that mass of adhesive plays a significant role in enhancing denture retention and supported the design principle of placing as few teeth as clinically necessary on the distal end of the free end saddles. Limiting the position of teeth on free end saddles to the mesial and mid portion of the saddle will reduce displacements caused by mastication. The movement of mandibular free end saddle partial dentures can be restricted with the use of denture adhesives. Altering the mass of adhesive used can further improve the retention of mandibular free end saddle partial dentures for patients. Copyright © 2017 Elsevier Ltd. All rights reserved.

Prevalence and distribution of dental anomalies: a comparison between maxillary and mandibular tooth agenesis.

PubMed

Al-Abdallah, Mariam; AlHadidi, Abeer; Hammad, Mohammad; Al-Ahmad, Hazem; Saleh, Raja'

2015-11-01

The aim of this study was to compare the pattern and prevalence of associated dental anomalies between maxillary and mandibular tooth agenesis (hypodontia). A sample of 3315 dental patients, aged 8.6 to 25.4 years, was surveyed for tooth agenesis (excluding third molars): 106 subjects were diagnosed with maxillary hypodontia (group 1) and 70 with mandibular hypodontia (group 2). Both groups were examined for the following dental anomalies: retained deciduous molars, infraocclusion of deciduous molars, impaction, microdontia of maxillary lateral incisors, supernumerary teeth, transposition, transmigration, and ectopic eruption of the permanent molars. For statistical testing, the chi-square test (P <0.05) was used to compare the occurrences of these anomalies among the groups. We found that 77.5% of the patients in the mandibular hypodontia group had at least 1 dental anomaly compared with 49.5% in the maxillary hypodontia group (P <0.0001). The only dental anomaly with a significantly increased prevalence in the maxillary hypodontia group compared with the mandibular hypodontia group was microdontia of the maxillary lateral incisors (groups 1, 46.7%; group 2, 12.9%; P <0.0001). On the other hand, the prevalences of retained deciduous molars (group 1, 9.4%; group 2, 60.0%), infraoccluded deciduous molars (group 1, 0.9%; group 2, 7.1%), and impacted teeth (group 1, 22.6%; group 2, 38.6%) were significantly higher in the mandibular hypodontia group. The prevalences of supernumerary teeth, transposition, transmigration, and ectopic eruption of permanent molars were low and not significantly different between the groups. Tooth agenesis isolated to the maxilla is frequently associated with microdontia of the maxillary lateral incisors, whereas tooth agenesis isolated to the mandible is frequently associated with retained deciduous molars, infraoccluded deciduous molars, and impacted teeth. The results of this study may provide additional evidence supporting the field-specific genetic control theory for dental development in both jaws. Copyright © 2015 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

A numerical simulation of tooth movement by wire bending.

PubMed

Kojima, Yukio; Fukui, Hisao

2006-10-01

In orthodontic treatment, wires are bent and attached to teeth to move them via elastic recovery. To predict how a tooth will move, the initial force system produced from the wire is calculated. However, the initial force system changes as the tooth moves and may not be used to predict the final tooth position. The purpose of this study was to develop a comprehensive mechanical, 3-dimensional, numerical model for predicting tooth movement. Tooth movements produced by wire bending were simulated numerically. The teeth moved as a result of bone remodeling, which occurs in proportion to stress in the periodontal ligament. With an off-center bend, a tooth near the bending position was subjected to a large moment and tipped more noticeably than the other teeth. Also, a tooth far from the bending position moved slightly in the mesial or the distal direction. With the center V-bend, when the second molar was added as an anchor tooth, the tipping angle and the intrusion of the canine increased, and movement of the first molar was prevented. When a wire with an inverse curve of Spee was placed in the mandibular arch, the calculated tendency of vertical tooth movements was the same as the measured result. In these tooth movements, the initial force system changed as the teeth moved. Tooth movement was influenced by the size of the root surface area. Tooth movements produced by wire bending could be estimated. It was difficult to predict final tooth positions from the initial force system.

Long-term movement patterns of a coral reef predator

NASA Astrophysics Data System (ADS)

Heupel, M. R.; Simpfendorfer, C. A.

2015-06-01

Long-term monitoring is required to fully define periodicity and patterns in animal movement. This is particularly relevant for defining what factors are driving the presence, location, and movements of individuals. The long-term movement and space use patterns of grey reef sharks, Carcharhinus amblyrhynchos, were examined on a whole of reef scale in the southern Great Barrier Reef to define whether movement and activity space varied through time. Twenty-nine C. amblyrhynchos were tracked for over 2 years to define movement patterns. All individuals showed high residency within the study site, but also had high roaming indices. This indicated that individuals remained in the region and used all of the monitored habitat (i.e., the entire reef perimeter). Use of space was consistent through time with high reuse of areas most of the year. Therefore, individuals maintained discrete home ranges, but undertook broader movements around the reef at times. Mature males showed greatest variation in movement with larger activity spaces and movement into new regions during the mating season (August-September). Depth use patterns also differed, suggesting behaviour or resource requirements varied between sexes. Examination of the long-term, reef-scale movements of C. amblyrhynchos has revealed that reproductive activity may play a key role in space use and activity patterns. It was unclear whether mating behaviour or an increased need for food to sustain reproductive activity and development played a greater role in these patterns. Reef shark movement patterns are becoming more clearly defined, but research is still required to fully understand the biological drivers for the observed patterns.

Movement Pattern Variability in Stone Knapping: Implications for the Development of Percussive Traditions

PubMed Central

Rein, Robert; Nonaka, Tetsushi; Bril, Blandine

2014-01-01

The earliest direct evidence for tool-use by our ancestors are 2.6 million year old stone tools from Africa. These earliest artifacts show that, already, early hominins had developed the required advanced movement skills and cognitive capacities to manufacture stone tools. Currently, it is not well understood, however, which specific movement skills are required for successful stone knapping and accordingly it is unknown how these skills emerged during early hominin evolution. In particular, it is not clear which striking movements are indicative of skilled performance, how striking movement patterns vary with task and environmental constraints, and how movement patterns are passed on within social groups. The present study addresses these questions by investigating striking movement patterns and striking variability in 18 modern stone knappers (nine experienced and nine novices). The results suggest that no single movement pattern characterizes successful stone knapping. Participants showed large inter-individual movement variability of the elementary knapping action irrespective of knapping experience and knapping performance. Changes in task- and environmental constraints led knappers to adapt their elementary striking actions using a combination of individual and common strategies. Investigation of striking pattern similarities within social groups showed only partial overlap of striking patterns across related individuals. The results therefore suggest that striking movement patterns in modern stone knappers are largely specific to the individual and movement variability is not indicative of knapping performance. The implications of these results for the development of percussive traditions are discussed. PMID:25426630

Mandibular fractures in British military personnel secondary to blast trauma sustained in Iraq and Afghanistan.

PubMed

Breeze, J; Gibbons, A J; Hunt, N C; Monaghan, A M; Gibb, I; Hepper, A; Midwinter, M

2011-12-01

Blast trauma is the primary cause of maxillofacial injury sustained by British service personnel on deployment, and the mandible is the maxillofacial structure most likely to be injured in combat, but there are few reports about the effect of blast trauma on it. The Joint Theatre Trauma Registry identified all mandibular fractures sustained by British servicemen secondary to blast injury between 1 January 2004 and 30 September 2009. These were matched to corresponding hospital notes from the Royal Centre for Defence Medicine (RCDM) for those evacuated servicemen and autopsy records for those who died of wounds. Seventy-four mandibular fractures were identified in 60 servicemen. Twenty-two soldiers were evacuated to the RCDM and the remaining 38 died from wounds. Fractures of the symphysis (39/106, 37%) and body (31/106, 29%) were more common than those of the angle (26/106, 25%) and condyle (10/106, 9%). This pattern of injury differs from that of civilian blunt trauma where the condyle is the site that is injured most often. Those fractures thought to result from the blast wave itself usually caused simple localised fractures, whereas those fractures thought to result from fragments of the blast caused comminution that affected several areas of the mandible. The pattern of fractures in personnel injured while they were inside a vehicle resembled that traditionally seen in blunt trauma, which supports the requirement for mandatory wearing of seat-belts in the rear of vehicles whenever tactically viable. All mandibular fractures in servicemen injured while in the turret of a vehicle had evidence of foreign bodies or radio-opaque fragments as a result of their exposed position. Many of these injuries could therefore be potentially prevented by the adoption of facial protection. Copyright © 2010 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Biomechanical analysis comparing natural and alloplastic temporomandibular joint replacement using a finite element model.

PubMed

Mesnard, Michel; Ramos, Antonio; Ballu, Alex; Morlier, Julien; Cid, M; Simoes, J A

2011-04-01

Prosthetic materials and bone present quite different mechanical properties. Consequently, mandible reconstruction with metallic materials (or a mandible condyle implant) modifies the physiologic behavior of the mandible (stress, strain patterns, and condyle displacements). The changing of bone strain distribution results in an adaptation of the temporomandibular joint, including articular contacts. Using a validated finite element model, the natural mandible strains and condyle displacements were evaluated. Modifications of strains and displacements were then assessed for 2 different temporomandibular joint implants. Because materials and geometry play important key roles, mechanical properties of cortical bone were taken into account in models used in finite element analysis. The finite element model allowed verification of the worst loading configuration of the mandibular condyle. Replacing the natural condyle by 1 of the 2 tested implants, the results also show the importance of the implant geometry concerning biomechanical mandibular behavior. The implant geometry and stiffness influenced mainly strain distribution. The different forces applied to the mandible by the elevator muscles, teeth, and joint loads indicate that the finite element model is a relevant tool to optimize implant geometry or, in a subsequent study, to choose a more suitable distribution of the screws. Bone screws (number and position) have a significant influence on mandibular behavior and on implant stress pattern. Stress concentration and implant fracture must be avoided. Copyright © 2011 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Finite element analysis of dental implant loading on atrophic and non-atrophic cancellous and cortical mandibular bone - a feasibility study.

PubMed

Marcián, Petr; Borák, Libor; Valášek, Jiří; Kaiser, Jozef; Florian, Zdeněk; Wolff, Jan

2014-12-18

The first aim of this study was to assess displacements and micro-strain induced on different grades of atrophic cortical and trabecular mandibular bone by axially loaded dental implants using finite element analysis (FEA). The second aim was to assess the micro-strain induced by different implant geometries and the levels of bone-to-implant contact (BIC) on the surrounding bone. Six mandibular bone segments demonstrating different grades of mandibular bone atrophy and various bone volume fractions (from 0.149 to 0.471) were imaged using a micro-CT device. The acquired bone STL models and implant (Brånemark, Straumann, Ankylos) were merged into a three-dimensional finite elements structure. The mean displacement value for all implants was 3.1 ±1.2 µm. Displacements were lower in the group with a strong BIC. The results indicated that the maximum strain values of cortical and cancellous bone increased with lower bone density. Strain distribution is the first and foremost dependent on the shape of bone and architecture of cancellous bone. The geometry of the implant, thread patterns, grade of bone atrophy and BIC all affect the displacement and micro-strain on the mandible bone. Preoperative finite element analysis could offer improved predictability in the long-term outlook of dental implant restorations. Copyright © 2014 Elsevier Ltd. All rights reserved.

Evolution of the vertebrate jaw: comparative embryology and molecular developmental biology reveal the factors behind evolutionary novelty

PubMed Central

Kuratani, Shigeru

2004-01-01

It is generally believed that the jaw arose through the simple transformation of an ancestral rostral gill arch. The gnathostome jaw differentiates from Hox-free crest cells in the mandibular arch, and this is also apparent in the lamprey. The basic Hox code, including the Hox-free default state in the mandibular arch, may have been present in the common ancestor, and jaw patterning appears to have been secondarily constructed in the gnathostomes. The distribution of the cephalic neural crest cells is similar in the early pharyngula of gnathostomes and lampreys, but different cell subsets form the oral apparatus in each group through epithelial–mesenchymal interactions: and this heterotopy is likely to have been an important evolutionary change that permitted jaw differentiation. This theory implies that the premandibular crest cells differentiate into the upper lip, or the dorsal subdivision of the oral apparatus in the lamprey, whereas the equivalent cell population forms the trabecula of the skull base in gnathostomes. Because the gnathostome oral apparatus is derived exclusively from the mandibular arch, the concepts ‘oral’ and ‘mandibular’ must be dissociated. The ‘lamprey trabecula’ develops from mandibular mesoderm, and is not homologous with the gnathostome trabecula, which develops from premandibular crest cells. Thus the jaw evolved as an evolutionary novelty through tissue rearrangements and topographical changes in tissue interactions. PMID:15575882

Associations between tongue movement pattern consistency and formant movement pattern consistency in response to speech behavioral modificationsa)

PubMed Central

Mefferd, Antje S.

2016-01-01

The degree of speech movement pattern consistency can provide information about speech motor control. Although tongue motor control is particularly important because of the tongue's primary contribution to the speech acoustic signal, capturing tongue movements during speech remains difficult and costly. This study sought to determine if formant movements could be used to estimate tongue movement pattern consistency indirectly. Two age groups (seven young adults and seven older adults) and six speech conditions (typical, slow, loud, clear, fast, bite block speech) were selected to elicit an age- and task-dependent performance range in tongue movement pattern consistency. Kinematic and acoustic spatiotemporal indexes (STI) were calculated based on sentence-length tongue movement and formant movement signals, respectively. Kinematic and acoustic STI values showed strong associations across talkers and moderate to strong associations for each talker across speech tasks; although, in cases where task-related tongue motor performance changes were relatively small, the acoustic STI values were poorly associated with kinematic STI values. These findings suggest that, depending on the sensitivity needs, formant movement pattern consistency could be used in lieu of direct kinematic analysis to indirectly examine speech motor control. PMID:27908069

Occlusion, sternocleidomastoid muscle activity, and body sway: a pilot study in male astronauts.

PubMed

Sforza, Chiarella; Tartaglia, Gianluca M; Solimene, Umberto; Morgun, Valery; Kaspranskiy, Rustem R; Ferrario, Virgilio F

2006-01-01

The modifications induced by microgravity on the coordinated patterns of movement of the head, trunk, and limbs are reported on extensively. However, apparently there is little data on the masticatory muscles. In normal gravitational conditions, information from the neck and stomatognathic apparatus play a role in maintaining the body's balance and equilibrium. The current pilot study used normal gravity conditions to investigate the hypothesis of a functional coupling between occlusion and neck muscles and body postural oscillations. The immediate effect of modified occlusal surfaces on the contraction pattern of the sternocleidomastoid muscles during maximum voluntary clenching and on the oscillation of the center of foot pressure was analyzed in 11 male astronauts (aged 31-54 yrs). All subjects were healthy and free from pathologies of the neck and stomatognathic apparatus. Occlusal splints were prepared using impressions of their dental arches. The splints were modeled on the mandibular arch, had only posterior contacts, and were modified to obtain a more symmetric, standardized contraction of the masseter and temporalis muscles during teeth clenching. Surface EMG activity of the sternocleidomastoid muscles was recorded during a maximal voluntary clench with and without the splint. Sternocleidomastoid potentials were standardized as percent of the mean potentials recorded during a maximum contralateral rotation of the head, and the symmetry of the EMG waves of left- and right-side muscles was measured. Body sway was assessed with and without the splint, either with eyes open or closed. The variations of the center of foot pressure were analyzed through bivariate analysis, and the area of the 90% standard ellipse was computed. Within each visual condition (eyes open or closed), the difference between the areas of oscillation measured with and without the splint was computed. Muscular activity was more symmetric with the splint. The area of oscillation of the center of foot pressure was larger without the splint than with the splint, both with eyes open and eyes closed. The modifications, induced by the occlusal splint in the sternocleidomastoid muscles' symmetry, and center of foot pressure differential area with closed eyes, were significantly related (p < 0.05): the larger the increment in muscular symmetry, the smaller the area of oscillation with the splint as compared to without the splint. A functionally more symmetric maxillo-mandibular position resulted in a more symmetric sternocleidomastoid muscle contraction pattern and less body sway. Modifications in the contraction of the masticatory muscles may therefore affect the whole body.

Qualitative assessment of awake nasopharyngoscopy for prediction of oral appliance treatment response in obstructive sleep apnoea.

PubMed

Sutherland, Kate; Chan, Andrew S L; Ngiam, Joachim; Darendeliler, M Ali; Cistulli, Peter A

2018-01-23

Clinical methods to identify responders to oral appliance (OA) therapy for obstructive sleep apnoea (OSA) are needed. Awake nasopharyngoscopy during mandibular advancement, with image capture and subsequent processing and analysis, may predict treatment response. A qualitative assessment of awake nasopharyngoscopy would be simpler for clinical practice. We aimed to determine if a qualitative classification system of nasopharyngoscopic observations reflects treatment response. OSA patients were recruited for treatment with a customised two-piece OA. A custom scoring sheet was used to record observations of the pharyngeal airway (velopharynx, oropharynx, hypopharynx) during supine nasopharyngoscopy in response to mandibular advancement and performance of the Müller manoeuvre. Qualitative scores for degree (< 25%, 25-50%, 50-75%, > 75%), collapse pattern (concentric, anteroposterior, lateral) and diameter change (uniform, anteroposterior, lateral) were recorded. Treatment outcome was confirmed by polysomnography after a titration period of 14.6 ± 9.8 weeks. Treatment response was defined as (1) Treatment AHI < 5, (2) Treatment AHI < 10 plus > 50% AHI reduction and (3) > 50% AHI reduction. Eighty OSA patients (53.8% male) underwent nasopharyngoscopy. The most common naspharyngoscopic observation with mandibular advancement was a small (< 50%) increase in velopharyngeal lateral diameter (37.5%). The majority of subjects (72.5%) were recorded as having > 75% velopharyngeal collapse on performance of the Müller manoeuvre. Mandibular advancement reduced the observed level of pharyngeal collapse at all three pharyngeal regions (p < 0.001). None of the nasopharyngoscopic qualitative scores differed between responder and non-responder groups. Qualitative assessment of awake nasopharyngoscopy appears useful for assessing the effect of mandibular advancement on upper airway collapsibility. However, it is not sensitive enough to predict oral appliance treatment outcome.

Effect of the bitterness of food on muscular activity and masticatory movement.

PubMed

Okada, Yamato; Shiga, Hiroshi

2017-10-01

The purpose of this study was to clarify the effect of the bitterness of food on muscular activity and masticatory movement. Twenty healthy subjects were asked to chew a non-bitter gummy jelly and a bitter gummy jelly on their habitual chewing side. The masseter muscular activity and the movement of mandibular incisal point were recorded simultaneously. For all cycles excluding the first cycle, parameters representing the muscular activity (total integral value and integral value per cycle) and masticatory movement (path, rhythm, and stability) were calculated and compared between the two types of gummy jellies. The total integral value of masseter muscular activity during the chewing of bitter gummy jelly was significantly smaller than during the chewing of non-bitter gummy jelly, however, no definite trends in the integral value per cycle and the stability of movement were observed. The parameters representing the movement path tended to be small during the chewing of bitter gummy jelly than during the chewing of non-bitter gummy jelly. The masticatory width was significantly smaller during the chewing of bitter gummy jelly. The parameters representing the rhythm of movement were significantly longer during the chewing of bitter gummy jelly than during the chewing of non-bitter gummy jelly. From these results it was suggested that the bitterness of food does not affect the integral value per cycle or the stability of the masticatory movement, but it does affect the movement path and rhythm, with narrowing of the path and slowing of the rhythm. Copyright © 2017 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Maxillary Expansion and Mandibular Setback Surgery With and Without Mandibular Anterior Segment Osteotomy to Correct Mandibular Prognathism With Obstructive Sleep Apnea.

PubMed

Han, Jeong Joon; Hong, Dong Hwan; Hwang, Soon Jung

2017-05-01

Mandibular prognathism is usually treated with mandibular setback surgery. However, this approach reduces the pharyngeal airway space, and can aggravate obstructive phenomena in patients with obstructive sleep apnea (OSA). While maxillary expansion is known to lead to an increase in the pharyngeal airway volume (PAS), its effect on the PAS in mandibular setback surgery has not yet been reported. The authors report a surgical approach with maxillary expansion in 2 patients with mandibular prognathism that was accompanied by OSA: maxillary midsagittal expansion with minimum maxillary advancement and minor mandibular setback without mandibular anterior segmental osteotomy (ASO) or major mandibular setback with mandibular ASO. Preoperative and postoperative computed tomography and polysomnography indicated that OSA was improved and pharyngeal airway space was increased or sustained, and the prognathic profile could be corrected to an acceptable facial esthetic profile. In summary, maxillary transversal expansion and mandibular setback with or without mandibular ASO can be successfully applied to treat mandibular prognathism with OSA.

Corticotomy-facilitated orthodontics using piezosurgery versus rotary instruments: an experimental study.

PubMed

Farid, Karim A; Mostafa, Yehya A; Kaddah, Mohammed A; El-Sharaby, Fouad Aly

2014-10-01

The aim of this study was to evaluate corticotomy-facilitated orthodontics (CFO) using piezosurgery versus conventional rotary instruments. Ten healthy adult male mongrel dogs of comparable age with a complete set of permanent dentition with average weights between 13-17 kilograms were used. CFO using conventional rotary instruments versus piezosurgery was performed on each dog in a split mouth design. For every dog, mandibular 2nd premolar retraction on each side was attempted after extracting 3rd premolars followed by corticotomy-facilitated orthodontics using conventional rotary surgical burs on the left side and an ultrasonic piezosurgery system on the right side of the same animal. Intraoral measurements of the rate of tooth movement were taken with a sliding caliper. Measurements were performed by the same operator at the time of surgery (appliance delivery) and every month for six months. The dogs were sacrificed after six months from initiation of tooth movement to evaluate the amount of tooth movement for both conventional rotary and piezosurgery corticotomy techniques. A statistically significantly higher mean amount of tooth movement for conventional rotary instrument versus the piezosurgery corticotomy technique was observed at all time intervals. Tooth movement was 1.6 times faster when CFO was done using conventional rotary instruments as compared to a piezosurgery device.

Reconstruction of large defects of the lips and commissure using a composite radial forearm palmaris longus free flap associated with a lengthening temporalis myoplasty.

PubMed

Martin, Thomas; Sury, Florent; Goga, Dominique; Parmentier, Jerome; Rozen, Adam; Laure, Boris

2012-08-01

We performed a single-stage operation to reconstruct a large defect of the lips and commissure using a composite radial forearm-palmaris longus free flap. To obtain cranial traction and a voluntary smile, independently from any jaw movement, traction was achieved by using a lengthening temporalis myoplasty. The tendon attached to the coronoid process was fixed to the palmaris longus tendon, recreating a new commissure and a "neo-modiolus." Physical therapy was started on the 21st postoperative day to facilitate progress from a "mandibular smile," to ideally a spontaneous and symmetric smile after 3 months of therapy. This procedure was able to obtain good oral continence and a good commissural movement during smile which has not previously been mentioned in the published literature.

Mandibular distraction osteogenesis with newly designed electromechanical distractor.

PubMed

Aykan, Andac; Ugurlutan, Rifat; Zor, Fatih; Ozturk, Serdar

2014-07-01

The purposes of this study were to design a fully automatic electromechanical distractor for continuous mandibular distraction osteogenesis and to investigate the efficacy of this newly developed distractor on sheep mandible model. Five sheep underwent unilateral mandibular osteotomy, and the mechanical component of electromechanical distractor was fixed on both sides of the osteotomy site using pins. After a 5-day latency period, the electromechanical distractor was activated at a rate of 0.30 mm per 8 hours using an electronic control unit. The bone was lengthened for 20 days without any intervention to the electromechanical distractor. The animals were killed on the sixth week of the consolidation period, and 5 distracted mandibles were examined through macroscopic observation and computed tomography. Distracted bone length was measured through computed tomography on sagittal slices. The device was tolerated by the distraction process without complications in all animals. New callus formation was observed on the distraction gap. Radiologic evaluation showed new callus formation in the distraction gap. New callus length was found to be, in average, 18.28 mm. In this preliminary study, a newly designed electromechanical distractor was successfully used for mandible distraction, which mainly provided a continuous lengthening during activation period spontaneously without any intervention. We think that the clinical application of this electromechanic distractor may provide patient comfort during distraction. Moreover, electromechanical distractor has the potential for high-resolution movement capacity when compared with annual distraction. The promising results from this prototype are encouraging to further investigations for human applications.

Comparison of Neck Screw and Conventional Fixation Techniques in Mandibular Condyle Fractures Using 3-Dimensional Finite Element Analysis.

PubMed

Conci, Ricardo Augusto; Tomazi, Flavio Henrique Silveira; Noritomi, Pedro Yoshito; da Silva, Jorge Vicente Lopes; Fritscher, Guilherme Genehr; Heitz, Claiton

2015-07-01

To compare the mechanical stress on the mandibular condyle after the reduction and fixation of mandibular condylar fractures using the neck screw and 2 other conventional techniques according to 3-dimensional finite element analysis. A 3-dimensional finite element model of a mandible was created and graphically simulated on a computer screen. The model was fixed with 3 different techniques: a 2.0-mm plate with 4 screws, 2 plates (1 1.5-mm plate and 1 2.0-mm plate) with 4 screws, and a neck screw. Loads were applied that simulated muscular action, with restrictions of the upper movements of the mandible, differentiation of the cortical and medullary bone, and the virtual "folds" of the plates and screws so that they could adjust to the condylar surface. Afterward, the data were exported for graphic visualization of the results and quantitative analysis was performed. The 2-plate technique exhibited better stability in regard to displacement of fractures, deformity of the synthesis materials, and minimum and maximum tension values. The results with the neck screw were satisfactory and were similar to those found when a miniplate was used. Although the study shows that 2 isolated plates yielded better results compared with the other groups using other fixation systems and methods, the neck screw could be an option for condylar fracture reduction. Copyright © 2015 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Analysis and evaluation of relative positions of mandibular third molar and mandibular canal impacts

PubMed Central

Kim, Hang-Gul

2014-01-01

Objectives This study used cone-beam computed tomography (CBCT) images to categorize the relationships between the mandibular canal and the roots and investigated the prevalence of nerve damage. Materials and Methods Through CBCT images, contact and three-dimensional positional relationships between the roots of the mandibular third molar and the mandibular canal were investigated. With this data, prevalence of nerve damage according to the presence of contact and three-dimensional positional relationships was studied. Other factors that affected the prevalence of nerve damage were also investigated. Results When the mandibular third molar and the mandibular canal were shown to have direct contact in CBCT images, the prevalence of nerve damage was higher than in other cases. Also, in cases where the mandibular canal was horizontally lingual to the mandibular third molar and the mandibular canal was vertically at the cervical level of the mandibular third molar, the prevalence of nerve damage was higher than in opposite cases. The percentage of mandibular canal contact with the roots of the mandibular third molar was higher when the mandibular canal was horizontally lingual to the mandibular third molar. Finally, the prevalence of nerve damage was higher when the diameter of the mandibular canal lumen suddenly decreased at the contact area between the mandibular canal and the roots, as shown in CBCT images. Conclusion The three-dimensional relationship of the mandibular third molar and the mandibular canal can help predict nerve damage and can guide patient expectations of the possibility and extent of nerve damage. PMID:25551092

The Endpoint Hypothesis: A Topological-Cognitive Assessment of Geographic Scale Movement Patterns

NASA Astrophysics Data System (ADS)

Klippel, Alexander; Li, Rui

Movement patterns of individual entities at the geographic scale are becoming a prominent research focus in spatial sciences. One pertinent question is how cognitive and formal characterizations of movement patterns relate. In other words, are (mostly qualitative) formal characterizations cognitively adequate? This article experimentally evaluates movement patterns that can be characterized as paths through a conceptual neighborhood graph, that is, two extended spatial entities changing their topological relationship gradually. The central questions addressed are: (a) Do humans naturally use topology to create cognitive equivalent classes, that is, is topology the basis for categorizing movement patterns spatially? (b) Are ‘all’ topological relations equally salient, and (c) does language influence categorization. The first two questions are addressed using a modification of the endpoint hypothesis stating that: movement patterns are distinguished by the topological relation they end in. The third question addresses whether language has an influence on the classification of movement patterns, that is, whether there is a difference between linguistic and non-linguistic category construction. In contrast to our previous findings we were able to document the importance of topology for conceptualizing movement patterns but also reveal differences in the cognitive saliency of topological relations. The latter aspect calls for a weighted conceptual neighborhood graph to cognitively adequately model human conceptualization processes.

Immunohistochemical Analysis on Cortex-to-Cortex Healing After Mandibular Vertical Ramus Osteotomy: A Preliminary Study.

PubMed

Jung, Hwi-Dong; Kim, Sang Yoon; Jung, Han-Sung; Park, Hyung-Sik; Jung, Young-Soo

2018-02-01

The present study analyzed the expression of specific cytokines in the transforming growth factor (TGF)-β superfamily postoperatively after mandibular vertical ramus osteotomy (VRO). Four beagle dogs were enrolled and euthanized at 1, 2, 4, and 8 weeks postoperatively for immunohistochemical analysis using 6 specific antibodies (bone morphogenetic protein [BMP]-2/4, BMP-7, TGF-β2, TGF-β3, matrix metalloproteinase-3, and vascular endothelial growth factor [VEGF]). The results from the surgical site and control (adjacent area) were compared. Generalized upregulation of BMP-2/4 was observed in all healing periods, and the strongest expression of BMP-7 was observed at 1 week postoperatively. The strongest expression of TGF-β2 was observed at 8 weeks with increasing pattern. The strong expression of TGF-β3 was observed at 1 and 4 weeks, with the strongest expression of VEGF at 1 week, with a decreasing pattern. No notable uptake was detected with the 6 specific antibodies in the adjacent bone (control). The absence of internal fixation after VRO led to dynamic healing with a specific expression pattern of BMP-7 and TGF-β2. The anatomic factors, including sufficient preexisting vascularity, led to the earlier expression pattern of VEGF. Copyright © 2017 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Effects of pulsed electromagnetic field vibration on tooth movement induced by magnetic and mechanical forces: a preliminary study.

PubMed

Darendeliler, M Ali; Zea, A; Shen, G; Zoellner, H

2007-12-01

This study was designed to determine whether or not high-frequency and low-magnitude vibration affects orthodontic tooth movement caused by magnetic or/and mechanical forces. Forty-four 7-week-old Wistar rats were randomly divided into four groups, with each group further divided into experimental and control subgroups. Neodymium-Iron-Boron (Nd-Fe-B) magnets and Sentalloy closed coil springs were placed between maxillary or mandibular first molars and incisors to activate tooth movement. The animals of experimental subgroups were exposed to the vibration induced by pulsed electromagnetic fields (PEMF) whilst the control subgroups were under normal atmosphere. The experiment lasted for 14 days and all of the animals were sacrificed for examination. The changes in the space between the molar and incisor were measured to indicate the amount of tooth movement. The coil springs, either with sham or active magnets, move molar much more than magnets alone, regardless of absence or presence of PEMF (p < 0.001). Under PEMF, the coil spring moved significantly more amount of tooth movement than that of coil-magnet combination (p < 0.01), as did the magnets compared to sham magnets (p < 0.019). Under a non-PEMF scenario, there was no significant difference in tooth movement between coil spring and coil-magnets combination, nor was there difference between magnets and sham magnets. It is suggested that the PEMF-induced vibration may enhance the effect of mechanical and magnetic forces on tooth movement.

Discovering loose group movement patterns from animal trajectories

USGS Publications Warehouse

Wang, Yuwei; Luo, Ze; Xiong, Yan; Prosser, Diann J.; Newman, Scott H.; Takekawa, John Y.; Yan, Baoping

2015-01-01

The technical advances of positioning technologies enable us to track animal movements at finer spatial and temporal scales, and further help to discover a variety of complex interactive relationships. In this paper, considering the loose gathering characteristics of the real-life groups' members during the movements, we propose two kinds of loose group movement patterns and corresponding discovery algorithms. Firstly, we propose the weakly consistent group movement pattern which allows the gathering of a part of the members and individual temporary leave from the whole during the movements. To tolerate the high dispersion of the group at some moments (i.e. to adapt the discontinuity of the group's gatherings), we further scheme the weakly consistent and continuous group movement pattern. The extensive experimental analysis and comparison with the real and synthetic data shows that the group pattern discovery algorithms proposed in this paper are similar to the the real-life frequent divergences of the members during the movements, can discover more complete memberships, and have considerable performance.

Useful Method for Intraoperative Monitoring of Facial Nerve in a Scarred Bed.

PubMed

Aysal, Bilge Kagan; Yapici, Abdulkerim; Bayram, Yalcin; Zor, Fatih

2016-10-01

Facial nerve is the main cranial nerve for the innervation of facial expression muscles. Main trunk of facial nerve passes approximately 1 to 2 cm deep to tragal pointer. In some patients, where a patient has multiple operations, fibrosis due to previous operations may change the natural anatomy and direction of the branches of facial nerve. A 22-year-old male patient had 2 operations for mandibular reconstruction after gunshot wound. During the second operation, there was a possible injury to the marginal mandibular nerve and a nerve stimulator was used intraoperatively to monitor the nerve at the tragal pointer because the excitability of the distal segments remains intact for 24 to 48 hours after nerve injuries. Thus, using a nerve stimulator at the operational site may lead to false-positive muscle movements in case of injuries. Using the nerve stimulator to stimulate the main trunk at the tragal point may help to distinguish the presence of possible injuries. A reliable method for intraoperative facial nerve monitoring in a scarred operational site was introduced in this letter.

Incisal Apical Root Resorption Evaluation after Low-Friction Orthodontic Treatment Using Two-Dimensional Radiographic Imaging and Trigonometric Correction.

PubMed

Savoldi, Fabio; Bonetti, Stefano; Dalessandri, Domenico; Mandelli, Gualtiero; Paganelli, Corrado

2015-11-01

Root resorption shall be taken into consideration during every orthodontic treatment, and it can be effected by the use of different techniques, such as the application of low friction mechanics. However, its routinely assessment on orthopantomography has limitations related to distortions and changes in dental inclination. The aim of this investigation was to evaluate the severity of apical root resorption of maxillary and mandibular incisors after low-friction orthodontic treatment, using the combination of panoramic and lateral radiographs, and applying a trigonometric correction. A hospital based Retrospective study at the orthodontic Department (Dental School, University of Brescia, Spedali Civili di Brescia, Brescia, Italy). Ninety-three subjects (53 females and 40 males; mean age, 14 years) with mild teeth crowding were treated without extractions by the same operator using a low-friction fixed appliance following an integrated straight wire (ISW) protocol. The pre- and post-treatment tooth lengths of the maxillary and mandibular incisors were measured on panoramic radiographs. A trigonometric factor of correction for the pre-treatment length was calculated based on the difference between the pre and post-treatment incisal inclination on lateral cephalograms. The changes in lengths were investigated using the Student's t-test for paired values (p<0.05). Maxillary central incisors showed no changes (0.3%, 0.6%), maxillary lateral incisors showed a small increase (1.4%, 1.8%) that was attributed to the completion of root development in younger patients, mandibular central and lateral incisors underwent slight resorption (-3.1%, -3.4%). A statistically significant difference was found for the mandibular incisors but not for the maxillary ones. In patients with mild crowding and consequent low amount of root movement, a low-friction orthodontic treatment can lead to slight apical root resorption, mainly involving lower incisors. The use of a trigonometric correction in the panoramic radiograph analysis may reduce the limitations of this 2D evaluation.

Movement Pattern and Parameter Learning in Children: Effects of Feedback Frequency

ERIC Educational Resources Information Center

Goh, Hui-Ting; Kantak, Shailesh S.; Sullivan, Katherine J.

2012-01-01

Reduced feedback during practice has been shown to be detrimental to movement accuracy in children but not in young adults. We hypothesized that the reduced accuracy is attributable to reduced movement parameter learning, but not pattern learning, in children. A rapid arm movement task that required the acquisition of a motor pattern scaled to…

Movement patterns of limb coordination in infant rolling.

PubMed

Kobayashi, Yoshio; Watanabe, Hama; Taga, Gentaro

2016-12-01

Infants must perform dynamic whole-body movements to initiate rolling, a key motor skill. However, little is known regarding limb coordination and postural control in infant rolling. To address this lack of knowledge, we examined movement patterns and limb coordination during rolling in younger infants (aged 5-7 months) that had just begun to roll and in older infants (aged 8-10 months) with greater rolling experience. Due to anticipated difficulty in obtaining measurements over the second half of the rolling sequence, we limited our analysis to the first half. Ipsilateral and contralateral limbs were identified on the basis of rolling direction and were classified as either a stationary limb used for postural stability or a moving limb used for controlled movement. We classified the observed movement patterns by identifying the number of stationary limbs and the serial order of combinational limb movement patterns. Notably, older infants performed more movement patterns that involved a lower number of stationary limbs than younger infants. Despite the wide range of possible movement patterns, a small group of basic patterns dominated in both age groups. Our results suggest that the fundamental structure of limb coordination during rolling in the early acquisition stages remains unchanged until at least 8-10 months of age. However, compared to younger infants, older infants exhibited a greater ability to select an effective rotational movement by positioning themselves with fewer stationary limbs and performing faster limb movements.

Abnormal motor patterns in the framework of the equilibrium-point hypothesis: a cause for dystonic movements?

PubMed

Latash, M L; Gutman, S R

1994-01-01

Until now, the equilibrium-point hypothesis (lambda model) of motor control has assumed nonintersecting force-length characteristics of the tonic stretch reflex for individual muscles. Limited data from animal experiments suggest, however, that such intersections may occur. We have assumed the possibility of intersection of the characteristics of the tonic stretch reflex and performed a computer simulation of movement trajectories and electromyographic patterns. The simulation has demonstrated, in particular, that a transient change in the slope of the characteristic of an agonist muscle may lead to temporary movement reversals, hesitations, oscillations, and multiple electromyographic bursts that are typical of movements of patients with dystonia. The movement patterns of three patients with idiopathic dystonia during attempts at fast single-joint movements (in the elbow, wrist, and ankle) were recorded and compared with the results of the computer simulation. This approach considers that motor disorders in dystonia result from faulty control patterns that may not correlate with any morphological or neurophysiological changes. It provides a basis for the high variability of dystonic movements. The uniqueness of abnormal motor patterns in dystonia, that precludes statistical analysis across patients, may result from subtle differences in the patterns of intersecting characteristics of the tonic stretch reflex. The applicability of our analysis to disordered multijoint movement patterns is discussed.

Orthodontic Consideration in Patients with Beta-Thalassemia Major: Case Report and Literature Review.

PubMed

Einy, Shmuel; Hazan-Molina, Hagai; Ben-Barak, Ayelet; Aizenbud, Dror

Beta Thalassemia (βT) patients present a unique facial appearance and specific craniofacial, jaw and dental patterns. Although this anomaly often requires orthodontic management, βT patients have received scant attention in the orthodontic and dental literature over the past 50 years. The aim of this article is to review the characteristic craniofacial and dental manifestation pattern of βT patients and to emphasize their preferred orthodontic management protocol by presenting a βT orthodontic treated patient. A 10 year old patient presented with a complaint of severe esthetic and functional disorders due to her diagnosis of βT. We initiated orthodontic treatment including a combined orthopedic and functional treatment modality to improve facial appearance. Maxillary restraint and increased mandibular size during treatment along with an increase in the vertical dimension were achieved. The patient presented with Angle class I molar relationship, with reduction of the excessive overjet and deep overbite. Orthodontic treatment comprised of maxillary orthopedic treatment directed especially toward premaxilla with light forces, and mandibular modification by functional appliance along with fixed orthodontic treatment is recommended in βT patients.

Differential expression of decorin and biglycan genes during mouse tooth development

NASA Technical Reports Server (NTRS)

Matsuura, T.; Duarte, W. R.; Cheng, H.; Uzawa, K.; Yamauchi, M.

2001-01-01

Small leucine-rich proteoglycans (SLRPs) have a number of biological functions and some of them are thought to regulate collagen mineralizaton in bone and tooth. We have previously identified and immunolocalized two members of the SLRPs family, decorin and biglycan, in bovine tooth/periodontium. To investigate their potential roles in tooth development, we examined the mRNA expression patterns of decorin, biglycan and type I collagen in newborn (day 19) mice tooth germs by in situ hybridization. At this developmental stage, the first maxillary and mandibular molars include stages before and after secretion of the predentin matrix, respectively. The expression of decorin mRNA coincided with that of type I collagen mRNA and was mostly observed in secretory odontoblasts, while the biglycan mRNA was expressed throughout the tooth germ, including pre-secretory odontoblasts/ameloblasts, dental papilla and stellate reticulum. However, its signal in secretory odontoblasts was not as evident as that of decorin. In mandibular incisors, where a significant amount of predentin matrix and a small amount of enamel matrix were already secreted, a similar differential expression pattern was observed. In secretory ameloblasts the biglycan mRNA expression was apparent, while that of decorin was not. These differential expression patterns suggest the distinct roles of biglycan and decorin in the process of tooth development.

Mathematical evaluation of the influence of multiple factors on implant stability quotient values in clinical practice: a retrospective study

PubMed Central

Huang, Hairong; Wismeijer, Daniel; Shao, Xianhong; Wu, Gang

2016-01-01

Objectives The objective of this study is to mathematically evaluate the influence of multiple factors on implant stability quotient values in clinical practice. Patients and methods Resonance frequency analysis was performed at T1 (measured immediately at the time of implant placement) and at T2 (measured before dental restoration) in 177 patients (329 implants). Using a multivariate linear regression model, we analyzed the influence of the following eleven candidate factors: sex, age, maxillary/mandibular location, bone type, immediate/delayed implantation, bone grafting (presence or absence), insertion torque, I-/II-stage healing pattern, implant diameter, implant length, and T1–T2 time interval. Results The following factors were identified to significantly influence the implant stability quotient (ISQ) values at T1: insertion torque, bone grafting, I-/II-stage healing pattern, immediate/delayed implantation, maxillary/mandibular location, implant diameter, and sex. In contrast, the ISQ values at T2 were significantly influenced only by three factors: implant diameter, T1–T2 time interval, and insertion torque. Conclusion Among the eleven candidate factors, seven key factors were found to influence the T1-ISQ values, while only three key factors influenced the T2-ISQ values. Both T1 and T2-ISQ values were found to be influenced by implant diameter and insertion torque. T1 was influenced specifically by the sex of the patient, the location (maxillary or mandibular), the implantation mode (immediate/delayed implantation), the healing stage, and the absence or presence of bone graft materials. PMID:27785040

Pattern of maxillary and mandibular proximal enamel thickness at the contact area of the permanent dentition from first molar to first molar.

PubMed

Sarig, Rachel; Vardimon, Alexander D; Sussan, Celine; Benny, Lea; Sarne, Ofer; Hershkovitz, Israel; Shpack, Nir

2015-04-01

Proximal enamel thickness (PET) at the mesial and distal contact areas of the complete permanent dentition has not been previously reported. Anatomic investigation of PET is essential for interproximal reduction treatment. Our objectives were to measure the PETs of the complete maxillary and mandibular dentitions at the contact areas, to compare the PETs of adjacent teeth, and to evaluate the vertical position of each contact area. We evaluated 720 extracted teeth; of these, 109 intact teeth were selected. The mesial and distal contact areas were demarcated, and each tooth was embedded in transparent epoxy resin. Blocks were prepared so that the 2 demarcated contact areas were exposed, and 6 measurements were taken and statistically analyzed. Both jaws showed the same PET pattern characterized by 5 features: PET increased progressively from incisor (0.63 mm) to first molar (1.48 mm). Per tooth, mesial and distal PET did not differ. Total maxillary (26.86 mm) and mandibular (24.52 mm) PETs were similar. Paired PETs at the interproximal interface were similar, with the exception of the lateral incisor-canine interfaces. From incisor to first molar, the contact area becomes located farther gingivally. The existing guideline of maximal 0.5-mm interproximal reduction per 2 adjacent teeth should be kept in the anterior region and could be increased to 1 mm in the posterior region, when an equal amount is removed. Copyright © 2015 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Subdivision of arthropod cap-n-collar expression domains is restricted to Mandibulata

PubMed Central

2014-01-01

Background The monophyly of Mandibulata - the division of arthropods uniting pancrustaceans and myriapods - is consistent with several morphological characters, such as the presence of sensory appendages called antennae and the eponymous biting appendage, the mandible. Functional studies have demonstrated that the patterning of the mandible requires the activity of the Hox gene Deformed and the transcription factor cap-n-collar (cnc) in at least two holometabolous insects: the fruit fly Drosophila melanogaster and the beetle Tribolium castaneum. Expression patterns of cnc from two non-holometabolous insects and a millipede have suggested conservation of the labral and mandibular domains within Mandibulata. However, the activity of cnc is unknown in crustaceans and chelicerates, precluding understanding of a complete scenario for the evolution of patterning of this appendage within arthropods. To redress these lacunae, here we investigate the gene expression of the ortholog of cnc in Parhyale hawaiensis, a malacostracan crustacean, and two chelicerates: the harvestman Phalangium opilio, and the scorpion Centruroides sculpturatus. Results In the crustacean P. hawaiensis, the segmental expression of Ph-cnc is the same as that reported previously in hexapods and myriapods, with two distinct head domains in the labrum and the mandibular segment. In contrast, Po-cnc and Cs-cnc expression is not enriched in the labrum of either chelicerate, but instead is expressed at comparable levels in all appendages. In further contrast to mandibulate orthologs, the expression domain of Po-cnc posterior to the labrum is not confined within the expression domain of Po-Dfd. Conclusions Expression data from two chelicerate outgroup taxa suggest that the signature two-domain head expression pattern of cnc evolved at the base of Mandibulata. The observation of the archetypal labral and mandibular segment domains in a crustacean exemplar supports the synapomorphic nature of mandibulate cnc expression. The broader expression of Po-cnc with respect to Po-Dfd in chelicerates further suggests that the regulation of cnc by Dfd was also acquired at the base of Mandibulata. To test this hypothesis, future studies examining panarthropod cnc evolution should investigate expression of the cnc ortholog in arthropod outgroups, such as Onychophora and Tardigrada. PMID:24405788

Movement and Movement Patterns of Early Childhood.

ERIC Educational Resources Information Center

Sinclair, Caroline B.

This study was undertaken to determine the progressive development in movement and movement patterns (coordinated movements of body parts used involuntarily to achieve an objective) of children 2- to 6-years-old, to identify general characteristics which may be studied for appraisal of growth and development, and to study variations in movement…

Anterior open-bite orthodontic treatment in an adult patient: A clinical case report.

PubMed

Gracco, Antonio; Siviero, Laura; de Stefani, Alberto; Bruno, Giovanni; Stellini, Edoardo

2016-06-01

A 45-year-old woman presented with an anterior open-bite complaining chiefly of her unpleasant smile esthetics and masticatory and speech problems. Treatment included speech therapy initiated immediately after bonding. Lingual spurs were positioned on the mandibular incisors in order to help tongue rehabilitation. During the working phase, temporary anchorage devices (TADs) were used at the mandibular anterior segment to intrude the lower left premolars. A splint was used to ensure retention in the upper and lower arches; an enveloppe linguale nocturne (ELN) was provided. Non-surgical open-bite treatment could offer a valid alternative to orthognanthic surgery when cephalometric evaluation shows no vertical growth pattern; patient compliance is essential to prevent relapse. Copyright © 2016 CEO. Published by Elsevier Masson SAS. All rights reserved.

Therapeutic objectives and surgical treatment of mandibular condyle fractures. Personal experience.

PubMed

Burlini, D

2004-10-01

A review of condylar fractures treated ''non-surgically'' and ''surgically'' over the last 5 years (1996-2001) at the Maxillofacial Surgery Division of the Brescia Civil Hospital (Italy) is presented. The non surgical and surgical treatments carried out, as well as their effectiveness and therapeutic aims, are illustrated. From June 1996 to June 2001, at the Maxillofacial Surgery Division of the Brescia Civil Hospital, 179 fractures of the mandibular condyle were treated. Of the 179 cases treated, a distinction was immediately made between ''non-surgical'' (103 cases) and ''surgical'' cases (76 cases). The 76 ''surgical'' cases were all treated with the same surgical technique. Out-patient follow-up was at days 20, 60, 90, and 1 year, together with a radiographic check-up at 60 days. Of the 76 condylar fractures treated surgically, 15 patients selected at random were re-examined; the medical history was investigated and clinical and radiological examinations performed. For each patient, the type of condylar fracture and whether this was associated with other mandibular fractures were recorded. The following data were also recorded: age of the patient; pain at the surgical site or at the mandible at the time of check-up; presence of normal occlusion and laterodeviation; any surgical sequelae at the facial nerve on the operated side; maximum mouth opening; any radiological defect; time since surgery. Then, the patient was asked to give his/her own evaluation of the surgical outcome, by expressing adequate, good or excellent result. In patients treated surgically the indication is almost absolute in the following cases: condylar fractures types II and IV of the Spiessl/Schroll classification, low or high condylar fractures with medial dislocation of the condyle; non-surgical treatment cannot be applied for reasons of patient's health; condylar fracture associated with other open fractures of the face. The use of rigid fixation also may help in the success of the technique adopted. In all the cases (surgical and non-surgical) it is important to achieve early mobilization of the mandible and carry out a rehabilitation program for masticatory function. The goals of condylar treatment may therefore be summarized as follows: to achieve a good occlusion; to eliminate pain; to achieve a proper mandibular symmetry; to achieve good mandibular movement in the 3 planes of space.

The role of simultaneous gap arthroplasty and distraction osteogenesis in the management of temporo-mandibular joint ankylosis with mandibular deformity in children.

PubMed

Rao, Krishna; Kumar, Sudhir; Kumar, Vijay; Singh, Arun Kumar; Bhatnagar, Sudhir Kumar

2004-02-01

Temporo-mandibular joint ankylosis is a common cause of acquired deformity in children. Surgical correction of the ankylosis only leaves the patient with an uncorrected mandibular deformity. This study was to evaluate the use of distraction osteogenesis for simultaneous correction of the mandibular deformity. This study was done on six children with temporo-mandibular joint ankylosis and mandibular deformity. Uniaxial double pin distractors with Schanz pins were used in this study. The patients underwent simultaneous gap arthroplasty and mandibular osteotomy (retromolar) with distractor insertion. Distraction was started on the fifth post-operative day. The patients were put on dynamic temporo-mandibular joint exercises on the first post-operative day. All patients had a satisfactory mouth opening on follow-up. Satisfactory cosmetic correction of the mandibular deformity was also achieved in all these patients. Some degree of malocclusion resulted from treatment due to which the patients were placed on orthodontic treatment. Distraction osteogenesis can be used simultaneously with gap arthroplasty in patients with temporo-mandibular ankylosis, for the correction of the mandibular deformity.

Memotain: A CAD/CAM nickel-titanium lingual retainer.

PubMed

Kravitz, Neal D; Grauer, Dan; Schumacher, Pascal; Jo, Yong-Min

2017-04-01

Approximately 1/2 of maxillary and 1/5 of mandibular multi-stranded lingual retainers fail during retention in some form, either bond failure or wire breakage. Memotain is a new CAD/CAM fabricated lingual retainer wire made of custom-cut nickel-titanium, as an alternative to multi-stranded lingual retainers. It offers numerous perceived advantages to the traditional multi-stranded stainless steel wire, including precision fit, avoidance of interferences, corrosion resistance and even the potential for minor tooth movement as an active lingual retainer. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

[Features of maxillary and mandibular nerves imaging during stem regional blockades. From paresthesia to 3D-CT guidance].

PubMed

Zaytsev, A Yu; Nazaryan, D N; Kim, S Yu; Dubrovin, K V; Svetlov, V A; Khovrin, V V

2014-01-01

There are difficulties in procedure of regional block of 2 and 3 brunches of the trigeminal nerve despite availability of many different methods of nerves imaging. The difficulties are connected with complex anatomy structure. Neurostimulation not always effective and as a rule, is accompanied with wrong interpretation of movement response on stimulation. The changing of the tactics on paraesthesia search improves the situation. The use of new methods of nerves imaging (3D-CT) also allows decreasing the frequency of fails during procedure of regional block of the brunches of the trigeminal nerve.

Histologic effects of intentional-socket-assisted orthodontic movement in rabbits.

PubMed

Yu, Ji-Yeon; Lee, Won; Park, Jae Hyun; Bayome, Mohamed; Kim, Yong; Kook, Yoon-Ah

2012-08-01

This study aimed to evaluate the effect of an intentionally created socket on bone remodeling with orthodontic tooth movement in rabbits. Eighteen male rabbits weighing 3.8 - 4.25 kg were used. An 8-mm deep and 2-mm wide socket was drilled in the bone 1 mm mesial to the right mandibular first premolar. The left first premolar was extracted to serve as an extraction socket. A traction force of 100 cN was applied to the right first premolar and left second premolar. Sections were obtained at the middle third of the moving tooth for both the drilled and extraction sockets and evaluated with hematoxylin and eosin staining and immunohistochemical analyses. The amount of tooth movement and tartrate-resistant acid phosphatase (TRAP)-positive cell count were compared between the 2 groups using the Mann-Whitney U test. At week 2, the distance of tooth movement was significantly higher in the intentional socket group (p < 0.05) than in the extraction socket group. The number of TRAP-positive cells decreased in week 2 but increased in week 3 (p < 0.05). However, there were no significant differences between the groups. Furthermore, results of transforming growth factor (TGF)-β staining revealed no significant differences. The intentional socket group showed greater distance of tooth movement than did the extraction socket group at week 2. Osteoclast counts and results of immunohistochemical analyses suggested elevated bone remodeling in both the groups. Thus, osteotomy may be an effective modality for enhancing tooth movement in orthodontic treatment.

Inducing any virtual two-dimensional movement in humans by applying muscle tendon vibration.

PubMed

Roll, Jean-Pierre; Albert, Frédéric; Thyrion, Chloé; Ribot-Ciscar, Edith; Bergenheim, Mikael; Mattei, Benjamin

2009-02-01

In humans, tendon vibration evokes illusory sensation of movement. We developed a model mimicking the muscle afferent patterns corresponding to any two-dimensional movement and checked its validity by inducing writing illusory movements through specific sets of muscle vibrators. Three kinds of illusory movements were compared. The first was induced by vibration patterns copying the responses of muscle spindle afferents previously recorded by microneurography during imposed ankle movements. The two others were generated by the model. Sixteen different vibratory patterns were applied to 20 motionless volunteers in the absence of vision. After each vibration sequence, the participants were asked to name the corresponding graphic symbol and then to reproduce the illusory movement perceived. Results showed that the afferent patterns generated by the model were very similar to those recorded microneurographically during actual ankle movements (r=0.82). The model was also very efficient for generating afferent response patterns at the wrist level, if the preferred sensory directions of the wrist muscle groups were first specified. Using recorded and modeled proprioceptive patterns to pilot sets of vibrators placed at the ankle or wrist levels evoked similar illusory movements, which were correctly identified by the participants in three quarters of the trials. Our proprioceptive model, based on neurosensory data recorded in behaving humans, should then be a useful tool in fields of research such as sensorimotor learning, rehabilitation, and virtual reality.

Improved single- and multi-contact life-time testing of dental restorative materials using key characteristics of the human masticatory system and a force/position-controlled robotic dental wear simulator.

PubMed

Raabe, D; Harrison, A; Ireland, A; Alemzadeh, K; Sandy, J; Dogramadzi, S; Melhuish, C; Burgess, S

2012-03-01

This paper presents a new in vitro wear simulator based on spatial parallel kinematics and a biologically inspired implicit force/position hybrid controller to replicate chewing movements and dental wear formations on dental components, such as crowns, bridges or a full set of teeth. The human mandible, guided by passive structures such as posterior teeth and the two temporomandibular joints, moves with up to 6 degrees of freedom (DOF) in Cartesian space. The currently available wear simulators lack the ability to perform these chewing movements. In many cases, their lack of sufficient DOF enables them only to replicate the sliding motion of a single occlusal contact point by neglecting rotational movements and the motion along one Cartesian axis. The motion and forces of more than one occlusal contact points cannot accurately be replicated by these instruments. Furthermore, the majority of wear simulators are unable to control simultaneously the main wear-affecting parameters, considering abrasive mechanical wear, which are the occlusal sliding motion and bite forces in the constraint contact phase of the human chewing cycle. It has been shown that such discrepancies between the true in vivo and the simulated in vitro condition influence the outcome and the quality of wear studies. This can be improved by implementing biological features of the human masticatory system such as tooth compliance realized through the passive action of the periodontal ligament and active bite force control realized though the central nervous system using feedback from periodontal preceptors. The simulator described in this paper can be used for single- and multi-occlusal contact testing due to its kinematics and ability to exactly replicate human translational and rotational mandibular movements with up to 6 DOF without neglecting movements along or around the three Cartesian axes. Recorded human mandibular motion and occlusal force data are the reference inputs of the simulator. Experimental studies of wear using this simulator demonstrate that integrating the biological feature of combined force/position hybrid control in dental material testing improves the linearity and reduces the variability of results. In addition, it has been shown that present biaxially operated dental wear simulators are likely to provide misleading results in comparative in vitro/in vivo one-contact studies due to neglecting the occlusal sliding motion in one plane which could introduce an error of up to 49% since occlusal sliding motion D and volumetric wear loss V(loss) are proportional.

[Orthodontic treatment of Class III patients with mandibular asymmetry].

PubMed

Duan, Yin-Zhong; Huo, Na; Chen, Lei; Chen, Xue-Peng; Lin, Yang

2008-12-01

To investigate the treatment outcome of Class III patients with dental, functional and mild skeletal mandibular asymmetry. Thirty-five patients (14 males and 21 females) with dental, functional and mild skeletal mandibular asymmetry were selected. The age range of the patients was 7 - 22 years with a mean age of 16.5 years. Dental mandibular asymmetry was treated with expansion of maxillary arch to help the mandible returning to normal position. Functional mandibular asymmetry was treated with activator or asymmetrical protraction and Class III elastics. Mild skeletal mandibular asymmetry was treated with camouflage treatment. Good occlusal relationships were achieved and facial esthetics was greatly improved after orthodontic treatment in patients with dental and functional mandibular asymmetry. However, patients with skeletal mandibular asymmetry should be treated with both extraction and genioplasty. Orthodontic treatment was suitable for patients with dental and functional mandibular asymmetry, while combined orthodontics and surgery could get good results in patients with skeletal mandibular asymmetry.

Patterns, severity, and management of maxillofacial injuries in a suburban South Western Nigeria tertiary center.

PubMed

Ogunmuyiwa, Stella Aimiede; Gbolahan, Olalere Omoyosola; Ayantunde, Abiodun Abraham; Odewabi, Adenike Abidemi

2015-01-01

Trauma remains a leading cause of maxillofacial injury globally. Changing etiological factors and patterns of maxillofacial injury continue to be reported and are largely modulated by socio-geographic and environmental factors. It is important to have an in-depth understanding of the pattern and etiology in a particular region before effective preventive measures can be developed. The aim was to evaluate the patterns, etiological factors, and management of maxillofacial injuries in Ogun state, Nigeria. A prospective descriptive cohort study of all consecutive patients that presented with maxillofacial injuries at our center between January and December 2013. Information about demographic data, types of maxillofacial and associated injury, etiology of injury, treatment received and complications were collected and analyzed. Seventy patients presented with maxillofacial injury during the study period with a male to female ratio of 4:1. The age range was 9 months to 60 years with a mean of 30.11 ± standard deviation 14.97 years. Majority of the facial fractures were due to motorcycle related crashes. There were 57.1% mandibular fractures and 55.7% middle third fractures. Closed reduction with maxillo-mandibular fixation was the major method of treatment of facial fractures. Postoperative complications were observed in 11.4% of patients. Road traffic crashes (RTCs) remain the leading etiological factor of maxillofacial injuries in our center. Enforcement of stricter traffic regulations and possibly replacement of motorcycles with tricycles for commercial transportation may help to reduce the incidence of RTCs.

Soft tissue changes and its stability as a sequlae to mandibular advancement.

PubMed

Uppada, Uday Kiran; Sinha, Ramen; Reddy, D Sreenatha; Paul, Dushyanth

2014-01-01

To predict the changes and evaluate the stability that occurs in the soft tissues following the skeletal movement subsequent to surgical advancement of the mandible through bilateral sagittal split osteotomy and to provide the patient reliable information with regard to esthetic changes that can be expected following the treatment. Twenty adult patients diagnosed with skeletal class II malocclusion and underwent bilateral sagittal split osteotomy for mandibular advancement by a mean of 8 mm using rigid fixation were included in the study. Soft tissue changes brought about by the surgical procedure and their stability over a period of time were evaluated prospectively using 12 linear (4 vertical and 8 horizontal) and 4 angular measurements on profile cephalograms which were taken preoperatively after the pre-surgical orthodontics (T1) and postoperatively with duration of 1 month (T2) and 6 months (T3) respectively. It was observed that compared to the linear measurements, the angular measurements showed significant changes. The improvement in the esthetic outcome is a direct reflection of the angular changes whereas the linear changes played a contributing role. Following mandibular advancement surgery the profiles of the patients was perceived to have improved with reduction in the facial convexity, an increase in the lower facial height, decrease in the depth of the mentolabial sulcus and improvement in the lip competency with lengthening, straightening and thinning of the lower lip. The soft tissue response and its stability depends on the stability of the surgical procedure itself, postsurgical growth and remodeling of the hard tissues and soft tissue changes as a result of maturation and aging.

Individual Movement Strategies Revealed through Novel Clustering of Emergent Movement Patterns

NASA Astrophysics Data System (ADS)

Valle, Denis; Cvetojevic, Sreten; Robertson, Ellen P.; Reichert, Brian E.; Hochmair, Hartwig H.; Fletcher, Robert J.

2017-03-01

Understanding movement is critical in several disciplines but analysis methods often neglect key information by adopting each location as sampling unit, rather than each individual. We introduce a novel statistical method that, by focusing on individuals, enables better identification of temporal dynamics of connectivity, traits of individuals that explain emergent movement patterns, and sites that play a critical role in connecting subpopulations. We apply this method to two examples that span movement networks that vary considerably in size and questions: movements of an endangered raptor, the snail kite (Rostrhamus sociabilis plumbeus), and human movement in Florida inferred from Twitter. For snail kites, our method reveals substantial differences in movement strategies for different bird cohorts and temporal changes in connectivity driven by the invasion of an exotic food resource, illustrating the challenge of identifying critical connectivity sites for conservation in the presence of global change. For human movement, our method is able to reliably determine the origin of Florida visitors and identify distinct movement patterns within Florida for visitors from different places, providing near real-time information on the spatial and temporal patterns of tourists. These results emphasize the need to integrate individual variation to generate new insights when modeling movement data.

Understanding eye movements in face recognition using hidden Markov models.

PubMed

Chuk, Tim; Chan, Antoni B; Hsiao, Janet H

2014-09-16

We use a hidden Markov model (HMM) based approach to analyze eye movement data in face recognition. HMMs are statistical models that are specialized in handling time-series data. We conducted a face recognition task with Asian participants, and model each participant's eye movement pattern with an HMM, which summarized the participant's scan paths in face recognition with both regions of interest and the transition probabilities among them. By clustering these HMMs, we showed that participants' eye movements could be categorized into holistic or analytic patterns, demonstrating significant individual differences even within the same culture. Participants with the analytic pattern had longer response times, but did not differ significantly in recognition accuracy from those with the holistic pattern. We also found that correct and wrong recognitions were associated with distinctive eye movement patterns; the difference between the two patterns lies in the transitions rather than locations of the fixations alone. © 2014 ARVO.

Convergence of marine megafauna movement patterns in coastal and open oceans.

PubMed

Sequeira, A M M; Rodríguez, J P; Eguíluz, V M; Harcourt, R; Hindell, M; Sims, D W; Duarte, C M; Costa, D P; Fernández-Gracia, J; Ferreira, L C; Hays, G C; Heupel, M R; Meekan, M G; Aven, A; Bailleul, F; Baylis, A M M; Berumen, M L; Braun, C D; Burns, J; Caley, M J; Campbell, R; Carmichael, R H; Clua, E; Einoder, L D; Friedlaender, Ari; Goebel, M E; Goldsworthy, S D; Guinet, C; Gunn, J; Hamer, D; Hammerschlag, N; Hammill, M; Hückstädt, L A; Humphries, N E; Lea, M-A; Lowther, A; Mackay, A; McHuron, E; McKenzie, J; McLeay, L; McMahon, C R; Mengersen, K; Muelbert, M M C; Pagano, A M; Page, B; Queiroz, N; Robinson, P W; Shaffer, S A; Shivji, M; Skomal, G B; Thorrold, S R; Villegas-Amtmann, S; Weise, M; Wells, R; Wetherbee, B; Wiebkin, A; Wienecke, B; Thums, M

2018-03-20

The extent of increasing anthropogenic impacts on large marine vertebrates partly depends on the animals' movement patterns. Effective conservation requires identification of the key drivers of movement including intrinsic properties and extrinsic constraints associated with the dynamic nature of the environments the animals inhabit. However, the relative importance of intrinsic versus extrinsic factors remains elusive. We analyze a global dataset of ∼2.8 million locations from >2,600 tracked individuals across 50 marine vertebrates evolutionarily separated by millions of years and using different locomotion modes (fly, swim, walk/paddle). Strikingly, movement patterns show a remarkable convergence, being strongly conserved across species and independent of body length and mass, despite these traits ranging over 10 orders of magnitude among the species studied. This represents a fundamental difference between marine and terrestrial vertebrates not previously identified, likely linked to the reduced costs of locomotion in water. Movement patterns were primarily explained by the interaction between species-specific traits and the habitat(s) they move through, resulting in complex movement patterns when moving close to coasts compared with more predictable patterns when moving in open oceans. This distinct difference may be associated with greater complexity within coastal microhabitats, highlighting a critical role of preferred habitat in shaping marine vertebrate global movements. Efforts to develop understanding of the characteristics of vertebrate movement should consider the habitat(s) through which they move to identify how movement patterns will alter with forecasted severe ocean changes, such as reduced Arctic sea ice cover, sea level rise, and declining oxygen content.

Movement pattern recognition in basketball free-throw shooting.

PubMed

Schmidt, Andrea

2012-04-01

The purpose of the present study was to analyze the movement patterns of free-throw shooters in basketball at different skill levels. There were two points of interest. First, to explore what information can be drawn from the movement pattern and second, to examine the methodological possibilities of pattern analysis. To this end, several qualitative and quantitative methods were employed. The resulting data were converged in a triangulation. Using a special kind of ANN named Dynamically Controlled Networks (DyCoN), a 'complex feature' consisting of several isolated features (angle displacements and velocities of the articulations of the kinematic chain) was calculated. This 'complex feature' was displayed by a trajectory combining several neurons of the network, reflecting the devolution of the twelve angle measures over the time course of each shooting action. In further network analyses individual characteristics were detected, as well as movement phases. Throwing patterns were successfully classified and the stability and variability of the realized pattern were established. The movement patterns found were clearly individually shaped as well as formed by the skill level. The triangulation confirmed the individual movement organizations. Finally, a high stability of the network methods was documented. Copyright © 2012. Published by Elsevier B.V.

Is having similar eye movement patterns during face learning and recognition beneficial for recognition performance? Evidence from hidden Markov modeling.

PubMed

Chuk, Tim; Chan, Antoni B; Hsiao, Janet H

2017-12-01

The hidden Markov model (HMM)-based approach for eye movement analysis is able to reflect individual differences in both spatial and temporal aspects of eye movements. Here we used this approach to understand the relationship between eye movements during face learning and recognition, and its association with recognition performance. We discovered holistic (i.e., mainly looking at the face center) and analytic (i.e., specifically looking at the two eyes in addition to the face center) patterns during both learning and recognition. Although for both learning and recognition, participants who adopted analytic patterns had better recognition performance than those with holistic patterns, a significant positive correlation between the likelihood of participants' patterns being classified as analytic and their recognition performance was only observed during recognition. Significantly more participants adopted holistic patterns during learning than recognition. Interestingly, about 40% of the participants used different patterns between learning and recognition, and among them 90% switched their patterns from holistic at learning to analytic at recognition. In contrast to the scan path theory, which posits that eye movements during learning have to be recapitulated during recognition for the recognition to be successful, participants who used the same or different patterns during learning and recognition did not differ in recognition performance. The similarity between their learning and recognition eye movement patterns also did not correlate with their recognition performance. These findings suggested that perceptuomotor memory elicited by eye movement patterns during learning does not play an important role in recognition. In contrast, the retrieval of diagnostic information for recognition, such as the eyes for face recognition, is a better predictor for recognition performance. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mandibular bone changes in 24 years and skeletal fracture prediction.

PubMed

Jonasson, G; Sundh, V; Hakeberg, M; Hassani-Nejad, A; Lissner, L; Ahlqwist, M

2013-03-01

The objectives of the investigation were to describe changes in mandibular bone structure with aging and to compare the usefulness of cortical and trabecular bone for fracture prediction. From 1968 to 1993, 1,003 women were examined. With the help of panoramic radiographs, cortex thickness was measured and cortex was categorized as: normal, moderately, or severely eroded. The trabeculation was assessed as sparse, mixed, or dense. Visually, the mandibular compact and trabecular bone transformed gradually during the 24 years. The compact bone became more porous, the intertrabecular spaces increased, and the radiographic image of the trabeculae seemed less mineralized. Cortex thickness increased up to the age of 50 and decreased significantly thereafter. At all examinations, the sparse trabeculation group had more fractures (71-78 %) than the non-sparse group (27-31 %), whereas the severely eroded compact group showed more fractures than the less eroded groups only in 1992/1993, 24 years later. Sparse trabecular pattern was associated with future fractures both in perimenopausal and older women (relative risk (RR), 1.47-4.37) and cortical erosion in older women (RR, 1.35-1.55). RR for future fracture associated with a severely eroded cortex increased to 4.98 for cohort 1930 in 1992/1993. RR for future fracture associated with sparse trabeculation increased to 11.43 for cohort 1922 in 1992/1993. Dental radiographs contain enough information to identify women most at risk of future fracture. When observing sparse mandibular trabeculation, dentists can identify 40-69 % of women at risk for future fractures, depending on participant age at examination.

Evaluation of arch width variations among different skeletal patterns in South Indian population.

PubMed

Prasad, Mandava; Kannampallil, Senny Thomas; Talapaneni, Ashok Kumar; George, Suja Ani; Shetty, Sharath Kumar

2013-01-01

Anterior cranial base can be taken as a reference line (SN) to determine the steepness of mandibular plane. Subjects with high mandibular plane angle tend to have a long face and one with low MP-SN angle has a shorter face. This study was done to investigate if dental arch widths correlated with vertical facial types and if there are any differences in arch widths between untreated male and female adults in South Indian population. Lateral cephalogram and dental casts were obtained from 180 untreated South Indian adults (90 males and 90 females) above 18 year old with no cross bite, minimal crowding and spacing. The angle between the anterior cranial base and the mandibular plane was measured on lateral cephalogram of each patient. Dental casts were used to obtain comprehensive dental measurements including maxillary and mandibular inter canine, inter premolar and inter molar widths, as well as amount of crowding or spacing. The results showed that male arch widths were significantly larger than those of females (P < 0.05) and there was a significant decrease in inter arch width as the MP-SN angle increased in untreated adult South Indian population. The results obtained in our study when compared with studies done in other population groups showed that there is difference in inter arch widths according to ethnicity and race. It was concluded that the dental arch width is associated with gender, race and vertical facial morphology. Thus using individualized arch wires according to each patient's pre treatment arch form and width is suggested during orthodontic treatment.

Characterizing mandibular growth using three-dimensional imaging techniques and anatomic landmarks

PubMed Central

Kelly, Michael P.; Vorperian, Houri K.; Wang, Yuan; Tillman, Katelyn K.; Werner, Helen M.; Chung, Moo K.; Gentry, Lindell R.

2017-01-01

Objective To provide quantitative data on the multi-planar growth of the mandible, this study derived accurate linear and angular mandible measurements using landmarks on three dimensional (3D) mandible models. This novel method was used to quantify 3D mandibular growth and characterize the emergence of sexual dimorphism. Design Cross-sectional and longitudinal imaging data were obtained from a retrospective computed tomography (CT) database for 51 typically developing individuals between the ages of one and nineteen years. The software Analyze was used to generate 104 3DCT mandible models. Eleven landmarks placed on the models defined six linear measurements (lateral condyle, gonion, and endomolare width, ramus and mental depth, and mandible length) and three angular measurements (gonion, gnathion, and lingual). A fourth degree polynomial fit quantified growth trends, its derivative quantified growth rates, and a composite growth model determined growth types (neural/cranial and somatic/skeletal). Sex differences were assessed in four age cohorts, each spanning five years, to determine the ontogenetic pattern producing sexual dimorphism of the adult mandible. Results Mandibular growth trends and growth rates were non-uniform. In general, structures in the horizontal plane displayed predominantly neural/cranial growth types, whereas structures in the vertical plane had somatic/skeletal growth types. Significant prepubertal sex differences in the inferior aspect of the mandible dissipated when growth in males began to outpace that of females at eight to ten years of age, but sexual dimorphism re-emerged during and after puberty. Conclusions This 3D analysis of mandibular growth provides preliminary normative developmental data for clinical assessment and craniofacial growth studies. PMID:28161602

Mandibular ramus shape variation and ontogeny in Homo sapiens and Homo neanderthalensis.

PubMed

Terhune, Claire E; Ritzman, Terrence B; Robinson, Chris A

2018-04-27

As the interface between the mandible and cranium, the mandibular ramus is functionally significant and its morphology has been suggested to be informative for taxonomic and phylogenetic analyses. In primates, and particularly in great apes and humans, ramus morphology is highly variable, especially in the shape of the coronoid process and the relationship of the ramus to the alveolar margin. Here we compare ramus shape variation through ontogeny in Homo neanderthalensis to that of modern and fossil Homo sapiens using geometric morphometric analyses of two-dimensional semilandmarks and univariate measurements of ramus angulation and relative coronoid and condyle height. Results suggest that ramus, especially coronoid, morphology varies within and among subadult and adult modern human populations, with the Alaskan Inuit being particularly distinct. We also identify significant differences in overall anterosuperior ramus and coronoid shapes between H. sapiens and H. neanderthalensis, both in adults and throughout ontogeny. These shape differences are subtle, however, and we therefore suggest caution when using ramus morphology to diagnose group membership for individual specimens of these taxa. Furthermore, we argue that these morphologies are unlikely to be representative of differences in masticatory biomechanics and/or paramasticatory behaviors between Neanderthals and modern humans, as has been suggested by previous authors. Assessments of ontogenetic patterns of shape change reveal that the typical Neanderthal ramus morphology is established early in ontogeny, and there is little evidence for divergent postnatal ontogenetic allometric trajectories between Neanderthals and modern humans as a whole. This analysis informs our understanding of intraspecific patterns of mandibular shape variation and ontogeny in H. sapiens and can shed further light on overall developmental and life history differences between H. sapiens and H. neanderthalensis. Copyright © 2018 Elsevier Ltd. All rights reserved.

Clinical signs of impending death in cancer patients.

PubMed

Hui, David; dos Santos, Renata; Chisholm, Gary; Bansal, Swati; Silva, Thiago Buosi; Kilgore, Kelly; Crovador, Camila Souza; Yu, Xiaoying; Swartz, Michael D; Perez-Cruz, Pedro Emilio; Leite, Raphael de Almeida; Nascimento, Maria Salete de Angelis; Reddy, Suresh; Seriaco, Fabiola; Yennu, Sriram; Paiva, Carlos Eduardo; Dev, Rony; Hall, Stacy; Fajardo, Julieta; Bruera, Eduardo

2014-06-01

The physical signs of impending death have not been well characterized in cancer patients. A better understanding of these signs may improve the ability of clinicians to diagnose impending death. We examined the frequency and onset of 10 bedside physical signs and their diagnostic performance for impending death. We systematically documented 10 physical signs every 12 hours from admission to death or discharge in 357 consecutive patients with advanced cancer admitted to two acute palliative care units. We examined the frequency and median onset of each sign from death backward and calculated their likelihood ratios (LRs) associated with death within 3 days. In total, 203 of 357 patients (52 of 151 in the U.S., 151 of 206 in Brazil) died. Decreased level of consciousness, Palliative Performance Scale ≤20%, and dysphagia of liquids appeared at high frequency and >3 days before death and had low specificity (<90%) and positive LR (<5) for impending death. In contrast, apnea periods, Cheyne-Stokes breathing, death rattle, peripheral cyanosis, pulselessness of radial artery, respiration with mandibular movement, and decreased urine output occurred mostly in the last 3 days of life and at lower frequency. Five of these signs had high specificity (>95%) and positive LRs for death within 3 days, including pulselessness of radial artery (positive LR: 15.6; 95% confidence interval [CI]: 13.7-17.4), respiration with mandibular movement (positive LR: 10; 95% CI: 9.1-10.9), decreased urine output (positive LR: 15.2; 95% CI: 13.4-17.1), Cheyne-Stokes breathing (positive LR: 12.4; 95% CI: 10.8-13.9), and death rattle (positive LR: 9; 95% CI: 8.1-9.8). We identified highly specific physical signs associated with death within 3 days among cancer patients. ©AlphaMed Press.

Mandibular position and movements: Suitability for diagnosis of sleep apnoea.

PubMed

Martinot, Jean-Benoit; Borel, Jean-Christian; Cuthbert, Valérie; Guénard, Hervé Jean-Pierre; Denison, Stéphane; Silkoff, Philip E; Gozal, David; Pepin, Jean-Louis

2017-04-01

Mandibular movements (MMs) and position during sleep reflect respiratory efforts related to increases in upper airway resistance and micro-arousals. The study objective was to assess whether MM identifies sleep-disordered breathing (SDB) in patients with moderate to high pre-test probability. This was a prospective study of 87 consecutive patients referred for an in-laboratory sleep test. Magnetometer-derived MM signals were incorporated into standard polysomnography (PSG). Respiratory events detected with MM analysis were compared with PSG for respiratory disturbance index (RDI) with a blinded scoring. All records were scored manually according to American Academy of Sleep Medicine rules. Primary outcome was to rule-in obstructive sleep apnoea syndrome (OSAS) defined as RDI cut-off value ≥5 or 15/h total sleep time (TST). High concordance emerged between MM and PSG-derived RDI with high temporal coincidence between events (R 2  = 0.906; P < 0.001). The mean diagnostic accuracy of MM for OSAS using RDI MM cut-off values of 5.9 and 13.5 was 0.935 (0.86-0.97) and 0.913 (0.84-0.95), with a mean positive likelihood ratio (LLR+) of 3.73 (2.7-20.4) and 8.46 (2.3-31.5), respectively. Receiver operating characteristic (ROC) curves at PSG cut-off values of 5 and 15/h TST had areas under the curve (AUC) of 0.96 (95% CI: 0.89-0.99) and 0.97 (95% CI: 0.91-0.99) (P < 0.001), respectively. MM analysis accurately identified SDB at different levels of severity. RDI assessed by MM is highly concordant with PSG, suggesting a role of ambulatory MM recordings to screen for SDB in patients with moderate to high pre-test probability. © 2016 Asian Pacific Society of Respirology.

Nonextraction and nonsurgical treatment of an adult with skeletal Class II open bite with severe retrognathic mandible and temporomandibular disorders.

PubMed

Kondo, Etsuko

2007-01-01

The treatment of an adult patient with a skeletal Class II Division 1 malocclusion, retrognathic mandible with downward and backward rotation, anterior open bite, and temporomandibular disorders is presented. Treatment objectives included establishing a stable occlusion with normal respiration, eliminating temporomandibular disorder symptoms, and improving facial esthetics through nonextraction and nonsurgical treatment. The patient was a Japanese adult female, who had previously been advised to have orthognathic surgery. An expansion plate was used to reshape the maxillary dentoalveolar arch. Distalization of the maxillary arch and forward movement of the mandible were achieved by reduced excessive posterior occlusal vertical dimension, through uprighting and intruding the mandibular posterior teeth, and rotating the mandible slightly upward and forward. The functional occlusal plane was reconstructed by uprighting and intruding the mandibular posterior teeth with a full-bracket appliance, combined with a maxillary expansion plate and short Class II elastics. Myofunctional therapy and masticatory and cervical muscle training involved chewing gum exercises and neck-muscle massage. The excessive posterior vertical occlusal dimension was significantly reduced, creating a small clearance between the posterior maxilla and mandible. The occlusal interferences in the posterior area were eliminated by the expansion of the maxillary dentoalveolar arch. As a result, the mandible moved forward, creating a more favorable jaw relationship. Distal movement of the maxillary arch was also achieved. The functional occlusal plane was reconstructed and a normal overjet and overbite were created. Adequate tongue space for normal respiration was established during the early stage of treatment. A stable occlusion with adequate posterior support and anterior guidance was established in a treatment time of 25 months, without orthognathic surgery, extraction, or headgear; this result was maintained at more than 1 year 8 months posttreatment.

Mandibular canine: A tool for sex identification in forensic odontology.

PubMed

Kumawat, Ramniwas M; Dindgire, Sarika L; Gadhari, Mangesh; Khobragade, Pratima G; Kadoo, Priyanka S; Yadav, Pradeep

2017-01-01

The aim of this study was to investigate the accuracy of mandibular canine index (MCI) and mandibular mesiodistal odontometrics in sex identification in the age group of 17-25 years in central Indian population. The study sample comprised total 300 individuals (150 males and 150 females) of an age group ranging from 17 to 25 years of central Indian population. The maximum mesiodistal diameter of mandibular canines, the linear distance between the tips of mandibular canines, was measured using digital vernier caliper on the study models. Overall sex could be predicted accurately in 79.66% (81.33% males and 78% females) of the population by MCI. Whereas, considering the mandibular canine width for sex identification, the overall accuracy was 75% for the right mandibular canine and 73% for the left mandibular canine observed. Sexual dimorphism of canine is population specific, and among the Indian population, MCI and mesiodistal dimension of mandibular canine can aid in sex determination.

Rotational Distraction for the Treatment of Severe Mandibular Retrognathia

PubMed Central

Mitsugi, Masaharu; Alcalde, Rafael E.; Yano, Tomoyuki; Uemura, Noriko; Okazaki, Mutsumi

2015-01-01

Backgrounds: The main problem with intraoral distraction of the mandible is the inability to achieve the three-dimensional mandibular correction as planned preoperatively. We developed a technique that allows spontaneous changes in the direction of mandibular elongation using an intraoral distractor. Methods: After mandibular osteotomy, the distractor is fixed to the distal segment of the mandible using a single bicortical screw, allowing anterior-posterior, vertical and limited lateromedial changes in the vector of distraction. Mandibular lengthening is performed while keeping the maxilla and mandible in class I occlusion with intermaxillary fixation. Results: As the distraction device is activated allowing mandibular elongation, the proximal segment, guided by the surrounding soft tissues, moves and rotates posterosuperiorly. Mandibular lengthening is continued until the condylar head reaches an adequate position in the mandibular fossa as confirmed clinically and radiographically. Conclusion Thirty-three patients with mandibular retrognathia received this treatment and good results were obtained. PMID:26301156

Rotational Distraction for the Treatment of Severe Mandibular Retrognathia.

PubMed

Ito, Osamu; Mitsugi, Masaharu; Alcalde, Rafael E; Yano, Tomoyuki; Uemura, Noriko; Okazaki, Mutsumi

2015-07-01

The main problem with intraoral distraction of the mandible is the inability to achieve the three-dimensional mandibular correction as planned preoperatively. We developed a technique that allows spontaneous changes in the direction of mandibular elongation using an intraoral distractor. After mandibular osteotomy, the distractor is fixed to the distal segment of the mandible using a single bicortical screw, allowing anterior-posterior, vertical and limited lateromedial changes in the vector of distraction. Mandibular lengthening is performed while keeping the maxilla and mandible in class I occlusion with intermaxillary fixation. As the distraction device is activated allowing mandibular elongation, the proximal segment, guided by the surrounding soft tissues, moves and rotates posterosuperiorly. Mandibular lengthening is continued until the condylar head reaches an adequate position in the mandibular fossa as confirmed clinically and radiographically. Thirty-three patients with mandibular retrognathia received this treatment and good results were obtained.

[Influence of the mandibular second premolar extraction on the angulation of the mandibular third molar].

PubMed

Feng, Guang-yao; Zou, Bing-shuang; Gao, Xue-mei; Zeng, Xiang-long; Wang, Xiu-jing; Yan, Yan

2013-02-18

To compare the angular changes in the developing mandibular third molars in the mandibular second premolar extraction and non-extraction cases and to determine whether the mandibular second premolar extraction causes favorable rotational changes in the angulations of the developing mandibular third molars and benefits its later eruption. Pretreatment and posttreatment panoramic radiographs were taken from 45 subjects who had been treated by the extraction of the mandibular second premolars and 48 subjects who had been treated without extraction. The horizontal reference plane was used to measure and compare the changes in the angulations of the developing mandibular third molars. The mean uprighting of the mandibular third molars seen in the extraction group was (5.9±2.5) degrees on the right side and (8.0±3.4) degrees on the left side following treatment. For the nonextraction group the mean uprighting was (1.8±2.4) degrees on the right side and (1.5±2.1) degrees on the left side. There was a statistically significant difference between the groups (P<0.05). Mandibular second premolar extraction might be a helpful procedure on the angulations of the developing mandibular third molars.

Pediatric facial fractures: evolving patterns of treatment.

PubMed

Posnick, J C; Wells, M; Pron, G E

1993-08-01

This study reviews the treatment of facial trauma between October 1986 and December 1990 at a major pediatric referral center. The mechanism of injury, location and pattern of facial fractures, pattern of facial injury, soft tissue injuries, and any associated injuries to other organ systems were recorded, and fracture management and perioperative complications reviewed. The study population consisted of 137 patients who sustained 318 facial fractures. Eighty-one patients (171 fractures) were seen in the acute stage, and 56 patients (147 fractures) were seen for reconstruction of a secondary deformity. Injuries in boys were more prevalent than in girls (63% versus 37%), and the 6- to 12-year cohort made up the largest group (42%). Most fractures resulted from traffic-related accidents (50%), falls (23%), or sports-related injuries (15%). Mandibular (34%) and orbital fractures (23%) predominated; fewer midfacial fractures (7%) were sustained than would be expected in a similar adult population. Three quarters of the patients with acute fractures required operative intervention. Closed reduction techniques with maxillomandibular fixation were frequently chosen for mandibular condyle fractures and open reduction techniques (35%) for other regions of the facial skeleton. When open reduction was indicated, plate-and-screw fixation was the preferred method of stabilization (65%). The long-term effects of the injuries and the treatment given on facial growth remain undetermined. Perioperative complication rates directly related to the surgery were low.

Eye Movements during Silent and Oral Reading in a Regular Orthography: Basic Characteristics and Correlations with Childhood Cognitive Abilities and Adolescent Reading Skills

PubMed Central

Krieber, Magdalena; Bartl-Pokorny, Katrin D.; Pokorny, Florian B.; Zhang, Dajie; Landerl, Karin; Körner, Christof; Pernkopf, Franz; Pock, Thomas; Einspieler, Christa; Marschik, Peter B.

2017-01-01

The present study aimed to define differences between silent and oral reading with respect to spatial and temporal eye movement parameters. Eye movements of 22 German-speaking adolescents (14 females; mean age = 13;6 years;months) were recorded while reading an age-appropriate text silently and orally. Preschool cognitive abilities were assessed at the participants’ age of 5;7 (years;months) using the Kaufman Assessment Battery for Children. The participants’ reading speed and reading comprehension at the age of 13;6 (years;months) were determined using a standardized inventory to evaluate silent reading skills in German readers (Lesegeschwindigkeits- und -verständnistest für Klassen 6–12). The results show that (i) reading mode significantly influenced both spatial and temporal characteristics of eye movement patterns; (ii) articulation decreased the consistency of intraindividual reading performances with regard to a significant number of eye movement parameters; (iii) reading skills predicted the majority of eye movement parameters during silent reading, but influenced only a restricted number of eye movement parameters when reading orally; (iv) differences with respect to a subset of eye movement parameters increased with reading skills; (v) an overall preschool cognitive performance score predicted reading skills at the age of 13;6 (years;months), but not eye movement patterns during either silent or oral reading. However, we found a few significant correlations between preschool performances on subscales of sequential and simultaneous processing and eye movement parameters for both reading modes. Overall, the findings suggest that eye movement patterns depend on the reading mode. Preschool cognitive abilities were more closely related to eye movement patterns of oral than silent reading, while reading skills predicted eye movement patterns during silent reading, but less so during oral reading. PMID:28151950

Feeding & Motor Functioning: Start at the Hips to Get to the Lips

ERIC Educational Resources Information Center

Donato, Jessica; Fox, Cathy; Mormon, Johnnie; Mormon, Mike

2008-01-01

Swallowing is one of the most complex movement patterns that people must use accurately throughout the day and night from the time they are born. These movement patterns are very closely integrated with breathing and movement of food through the aerodigestive tract. Malalignment or dysfunction in any part of these integrated patterns and systems…

Patterns of Movement in Foster Care: An Optimal Matching Analysis

PubMed Central

Havlicek, Judy

2011-01-01

Placement instability remains a vexing problem for child welfare agencies across the country. This study uses child welfare administrative data to retrospectively follow the entire placement histories (birth to age 17.5) of 474 foster youth who reached the age of majority in the state of Illinois and to search for patterns in their movement through the child welfare system. Patterns are identified through optimal matching and hierarchical cluster analyses. Multiple logistic regression is used to analyze administrative and survey data in order to examine covariates related to patterns. Five distinct patterns of movement are differentiated: Late Movers, Settled with Kin, Community Care, Institutionalized, and Early Entry. These patterns suggest high but variable rates of movement. Implications for child welfare policy and service provision are discussed. PMID:20873020

Targeted presurgical decompensation in patients with yaw-dependent facial asymmetry

PubMed Central

Kim, Kyung-A; Lee, Ji-Won; Park, Jeong-Ho; Kim, Byoung-Ho; Ahn, Hyo-Won

2017-01-01

Facial asymmetry can be classified into the rolling-dominant type (R-type), translation-dominant type (T-type), yawing-dominant type (Y-type), and atypical type (A-type) based on the distorted skeletal components that cause canting, translation, and yawing of the maxilla and/or mandible. Each facial asymmetry type represents dentoalveolar compensations in three dimensions that correspond to the main skeletal discrepancies. To obtain sufficient surgical correction, it is necessary to analyze the main skeletal discrepancies contributing to the facial asymmetry and then the skeletal-dental relationships in the maxilla and mandible separately. Particularly in cases of facial asymmetry accompanied by mandibular yawing, it is not simple to establish pre-surgical goals of tooth movement since chin deviation and posterior gonial prominence can be either aggravated or compromised according to the direction of mandibular yawing. Thus, strategic dentoalveolar decompensations targeting the real basal skeletal discrepancies should be performed during presurgical orthodontic treatment to allow for sufficient skeletal correction with stability. In this report, we document targeted decompensation of two asymmetry patients focusing on more complicated yaw-dependent types than others: Y-type and A-type. This may suggest a clinical guideline on the targeted decompensation in patient with different types of facial asymmetries. PMID:28523246

Targeted presurgical decompensation in patients with yaw-dependent facial asymmetry.

PubMed

Kim, Kyung-A; Lee, Ji-Won; Park, Jeong-Ho; Kim, Byoung-Ho; Ahn, Hyo-Won; Kim, Su-Jung

2017-05-01

Facial asymmetry can be classified into the rolling-dominant type (R-type), translation-dominant type (T-type), yawing-dominant type (Y-type), and atypical type (A-type) based on the distorted skeletal components that cause canting, translation, and yawing of the maxilla and/or mandible. Each facial asymmetry type represents dentoalveolar compensations in three dimensions that correspond to the main skeletal discrepancies. To obtain sufficient surgical correction, it is necessary to analyze the main skeletal discrepancies contributing to the facial asymmetry and then the skeletal-dental relationships in the maxilla and mandible separately. Particularly in cases of facial asymmetry accompanied by mandibular yawing, it is not simple to establish pre-surgical goals of tooth movement since chin deviation and posterior gonial prominence can be either aggravated or compromised according to the direction of mandibular yawing. Thus, strategic dentoalveolar decompensations targeting the real basal skeletal discrepancies should be performed during presurgical orthodontic treatment to allow for sufficient skeletal correction with stability. In this report, we document targeted decompensation of two asymmetry patients focusing on more complicated yaw-dependent types than others: Y-type and A-type. This may suggest a clinical guideline on the targeted decompensation in patient with different types of facial asymmetries.

Upper airway changes after Xbow appliance therapy evaluated with cone beam computed tomography.

PubMed

Erbas, Banu; Kocadereli, Ilken

2014-07-01

To determine the treatment effects of the Xbow appliance on the upper airway dimensions and volume using cone-beam computed tomography (CBCT); to evaluate the cephalometric changes in the skeletal and dental structures of the skeletal Class II patients. The sample consisted of 25 Class II patients (11 male, 14 female) with a mean age of 11.1 ± 1.1 years. CBCT images were obtained at the beginning of the treatment (T0) and after the debonding of the Xbow (T1). Changes in superior, middle, and inferior parts of the oropharynx in the retroglossal region and changes in the oropharyngeal airway volume were statistically significant (P < .05, P < .01). The differences favoring the Xbow for the changes in the direction of Class II correction included SNA, SNB, ANB, maxillary depth angles, and point A-NPg and Co-B distances. Data of the dental parameters showed palatal tipping and extrusion of the maxillary incisors, labial tipping of the mandibular incisors, and mesial movement and extrusion of the mandibular molars. Treatment with the Xbow appliance in Class II patients resulted in favorable increase in the oropharyngeal airway dimensions and volume. Further studies with larger study samples and with control groups are needed.

Strategy of arm movement control is determined by minimization of neural effort for joint coordination.

PubMed

Dounskaia, Natalia; Shimansky, Yury

2016-06-01

Optimality criteria underlying organization of arm movements are often validated by testing their ability to adequately predict hand trajectories. However, kinematic redundancy of the arm allows production of the same hand trajectory through different joint coordination patterns. We therefore consider movement optimality at the level of joint coordination patterns. A review of studies of multi-joint movement control suggests that a 'trailing' pattern of joint control is consistently observed during which a single ('leading') joint is rotated actively and interaction torque produced by this joint is the primary contributor to the motion of the other ('trailing') joints. A tendency to use the trailing pattern whenever the kinematic redundancy is sufficient and increased utilization of this pattern during skillful movements suggests optimality of the trailing pattern. The goal of this study is to determine the cost function minimization of which predicts the trailing pattern. We show that extensive experimental testing of many known cost functions cannot successfully explain optimality of the trailing pattern. We therefore propose a novel cost function that represents neural effort for joint coordination. That effort is quantified as the cost of neural information processing required for joint coordination. We show that a tendency to reduce this 'neurocomputational' cost predicts the trailing pattern and that the theoretically developed predictions fully agree with the experimental findings on control of multi-joint movements. Implications for future research of the suggested interpretation of the trailing joint control pattern and the theory of joint coordination underlying it are discussed.

Correlation of panoramic radiography and cone beam CT findings in the assessment of the relationship between impacted mandibular third molars and the mandibular canal

PubMed Central

Neves, F S; Souza, T C; Almeida, S M; Haiter-Neto, F; Freitas, D Q; Bóscolo, F N

2012-01-01

Objectives The aim of this study was to assess the reliability of four panoramic radiographic findings, both individually and in association, in predicting the absence of corticalization between the mandibular canal and the third molar on cone beam CT (CBCT) images. Methods The sample consisted of 72 individuals (142 mandibular third molars) who underwent pre-operative radiographic evaluation before extraction of impacted mandibular third molars. On panoramic radiographs, the most common signs of corticalization (darkening of roots, diversion of mandibular canal, narrowing of mandibular canal and interruption of white line) and the presence or absence of corticalization between the mandibular third molar and the mandibular canal on CBCT images were evaluated. Results Darkening of roots and interruption of white line associated with the absence of corticalization between the mandibular third molar and the mandibular canal on CBCT images were statistically significant, both as isolated findings (p = 0.0001 and p = 0.0006, respectively) and in association (p = 0.002). No statistically significant association was observed for the other panoramic radiographic findings, either individually or in association (p > 0.05). Conclusion Darkening of roots and interruption of white line observed on panoramic radiographs, both as isolated findings and in association, were effective in determining the risk relationship between the tooth roots and the mandibular canal, requiring three-dimensional evaluation of the case. PMID:22282507

Prevalence of Temporal Bone Fractures in Patients with Mandibular Fractures Using Multidetector-Row CT.

PubMed

Ogura, I; Kaneda, T; Sasaki, Y; Buch, K; Sakai, O

2015-06-01

Temporal bone fracture after mandibular trauma is thought to be rare, and its prevalence has not been reported in the literature. The purpose of this study was to investigate the prevalence of temporal bone fractures in patients with mandibular fractures and the relationship between temporal bone fractures and the mandibular fracture location using multidetector-row computed tomography (MDCT). A prospective study was performed in 201 patients with mandibular fractures who underwent 64-MDCT scans. The mandibular fracture locations were classified as median, paramedian, angle, and condylar types. Statistical analysis for the relationship between prevalence of temporal bone fractures and mandibular fracture locations was performed using χ(2) test with Fisher's exact test. A P-value < 0.05 was considered statistically significant. The percentage of cases with temporal bone fracture was 3.0 % of all patients with mandibular fractures and 19.0 % of those with multiple mandibular fractures of paramedian and condylar type. There was a significant relationship between the incidence of temporal bone fracture and the paramedian- and condylar-type mandibular fracture (P = 0.001). Multiple mandibular fractures of paramedian and condylar type may be a stronger indicator for temporal bone fractures. This study suggests that patients with mandibular fracture, especially the paramedian and condylar type, should be examined for coexisting temporal bone fracture using MDCT.

HNK-1 immunoreactivity during early morphogenesis of the head region in a nonmodel vertebrate, crocodile embryo

NASA Astrophysics Data System (ADS)

Kundrát, Martin

2008-11-01

The present study examines HNK-1 immunoidentification of a population of the neural crest (NC) during early head morphogenesis in the nonmodel vertebrate, the crocodile ( Crocodylus niloticus) embryos. Although HNK-1 is not an exclusive NC marker among vertebrates, temporospatial immunoreactive patterns found in the crocodile are almost consistent with NC patterns derived from gene expression studies known in birds (the closest living relatives of crocodiles) and mammals. In contrast to birds, the HNK-1 epitope is immunoreactive in NC cells at the neural fold level in crocodile embryos and therefore provides sufficient base to assess early migratory events of the cephalic NC. I found that crocodile NC forms three classic migratory pathways in the head: mandibular, hyoid, and branchial. Further, I demonstrate that, besides this classic phenotype, there is also a forebrain-derived migratory population, which consolidates into a premandibular stream in the crocodile. In contrast to the closely related chick model, crocodilian premandibular and mandibular NC cells arise from the open neural tube suggesting that species-specific heterochronic behavior of NC may be involved in the formation of different vertebrate facial phenotypes.

Comparative stress distribution of implant-retained mandibular ball-supported and bar-supported overlay dentures: a finite element analysis.

PubMed

Vafaei, Fariborz; Khoshhal, Masoumeh; Bayat-Movahed, Saeed; Ahangary, Ahmad Hassan; Firooz, Farnaz; Izady, Alireza; Rakhshan, Vahid

2011-08-01

Implant-retained mandibular ball-supported and bar-supported overlay dentures are the two most common treatment options for the edentulous mandible. The superior option in terms of strain distribution should be determined. The three-dimensional model of mandible (based on computerized tomography scan) and its overlying implant-retained bar-supported and ball-supported overlay dentures were simulated using SolidWorks, NURBS, and ANSYS Workbench. Loads A (60 N) and B (60 N) were exerted, respectively, in protrusive and laterotrusive motions, on second molar mesial, first molar mesial, and first premolar. The strain distribution patterns were assessed on (1) implant tissue, (2) first implant-bone, and (3) second implant-bone interfaces. Protrusive: Strain was mostly detected in the apical of the fixtures and least in the cervical when bar design was used. On the nonworking side, however, strain was higher in the cervical and lower in the apical compared with the working side implant. Laterotrusive: The strain values were closely similar in the two designs. It seems that both designs are acceptable in terms of stress distribution, although a superior pattern is associated with the application of bar design in protrusive motion.

Do flexible acrylic resin lingual flanges improve retention of mandibular complete dentures?

PubMed Central

Ahmed Elmorsy, Ayman Elmorsy; Ahmed Ibraheem, Eman Mostafa; Ela, Alaa Aboul; Fahmy, Ahmed; Nassani, Mohammad Zakaria

2015-01-01

Objectives: The aim of this study was to compare the retention of conventional mandibular complete dentures with that of mandibular complete dentures having lingual flanges constructed with flexible acrylic resin “Versacryl.” Materials and Methods: The study sample comprised 10 completely edentulous patients. Each patient received one maxillary complete denture and two mandibular complete dentures. One mandibular denture was made of conventional heat-cured acrylic resin and the other had its lingual flanges made of flexible acrylic resin Versacryl. Digital force-meter was used to measure retention of mandibular dentures at delivery and at 2 weeks and 45 days following denture insertion. Results: The statistical analysis showed that at baseline and follow-up appointments, retention of mandibular complete dentures with flexible lingual flanges was significantly greater than retention of conventional mandibular dentures (P < 0.05). In both types of mandibular dentures, retention of dentures increased significantly over the follow-up period (P < 0.05). Conclusions: The use of flexible acrylic resin lingual flanges in the construction of mandibular complete dentures improved denture retention. PMID:26539387

Movement patterns of Tenebrio beetles demonstrate empirically that correlated-random-walks have similitude with a Lévy walk.

PubMed

Reynolds, Andy M; Leprêtre, Lisa; Bohan, David A

2013-11-07

Correlated random walks are the dominant conceptual framework for modelling and interpreting organism movement patterns. Recent years have witnessed a stream of high profile publications reporting that many organisms perform Lévy walks; movement patterns that seemingly stand apart from the correlated random walk paradigm because they are discrete and scale-free rather than continuous and scale-finite. Our new study of the movement patterns of Tenebrio molitor beetles in unchanging, featureless arenas provides the first empirical support for a remarkable and deep theoretical synthesis that unites correlated random walks and Lévy walks. It demonstrates that the two models are complementary rather than competing descriptions of movement pattern data and shows that correlated random walks are a part of the Lévy walk family. It follows from this that vast numbers of Lévy walkers could be hiding in plain sight.

The role of insect dispersal and migration in population processes

NASA Technical Reports Server (NTRS)

Rabb, R. L.; Stinner, R. E.

1979-01-01

Movement functions in the population dynamics of insects are discussed. Modes of movement, movement from a population view, and population patterns are described and predicted. A wide-area of spatial and temporal patterns are presented.

An equilibrium-point model for fast, single-joint movement: I. Emergence of strategy-dependent EMG patterns.

PubMed

Latash, M L; Gottlieb, G L

1991-09-01

We describe a model for the regulation of fast, single-joint movements, based on the equilibrium-point hypothesis. Limb movement follows constant rate shifts of independently regulated neuromuscular variables. The independently regulated variables are tentatively identified as thresholds of a length sensitive reflex for each of the participating muscles. We use the model to predict EMG patterns associated with changes in the conditions of movement execution, specifically, changes in movement times, velocities, amplitudes, and moments of limb inertia. The approach provides a theoretical neural framework for the dual-strategy hypothesis, which considers certain movements to be results of one of two basic, speed-sensitive or speed-insensitive strategies. This model is advanced as an alternative to pattern-imposing models based on explicit regulation of timing and amplitudes of signals that are explicitly manifest in the EMG patterns.

The Effect of Core Stability Training on Functional Movement Patterns in Collegiate Athletes.

PubMed

Bagherian, Sajad; Ghasempoor, Khodayar; Rahnama, Nader; Wikstrom, Erik A

2018-02-06

Pre-participation examinations are the standard approach for assessing poor movement quality that would increase musculoskeletal injury risk. However, little is known about how core stability influences functional movement patterns. The primary purpose of this study was to determine the effect of an 8-week core stability program on functional movement patterns in collegiate athletes. The secondary purpose was to determine if the core stability training program would be more effective in those with worse movement quality (i.e. ≤14 baseline FMS score). Quasi-experimental design. Athletic Training Facility. One-hundred collegiate athletes. Functional movement patterns included the Functional Movement Screen (FMS), Lateral step down (LSD) and Y balance test (YBT) and were assessed before and after the 8-week program. Participants were placed into 1 of the 2 groups: intervention and control. The intervention group was required to complete a core stability training program that met 3 times per week for 8-week. Significant group x time interactions demonstrated improvements in FMS, LSD and YBT scores in the experimental group relative to the control group (p<0.001). Independent sample t-tests demonstrate that change scores were larger (greater improvement) for the FMS total score and Hurdle step (p<0.001) in athletes with worse movement quality. An 8-week core stability training program enhances functional movement patterns and dynamic postural control in collegiate athletes. The benefits are more pronounced in collegiate athletes with poor movement quality.

Coarse-scale movement patterns of a small-bodied fish inhabiting a desert stream

USGS Publications Warehouse

Dzul, M.C.; Quist, M.C.; Dinsmore, S.J.; Gaines, D.B.; Bower, M.R.

2013-01-01

Located on the floor of Death Valley (CA, USA), Salt Creek harbors a single fish species, the Salt Creek pupfish, Cyprinodon salinus salinus, which has adapted to this extremely harsh environment. Salt Creek is fed by an underground spring and is comprised of numerous pools, runs, and marshes that exhibit substantial variability in temperature, salinity, and dissolved oxygen concentrations. In addition, the wetted area of Salt Creek is reduced throughout the summer months due to high rates of evaporation, with some reaches drying completely. Therefore, it seems logical that short- and long-term movement patterns may play an important role in Salt Creek pupfish population dynamics. The objective of this study was to describe coarse-scale movements of Salt Creek pupfish in Salt Creek during their breeding season from March to May. Sex ratios and length–frequency distributions varied spatially within Salt Creek, suggesting population segregation during the breeding season. Long-distance movements were generally rare, although two fish moved more than 1.2 km. Movement in upstream reaches was rare or absent, in contrast to the greater movement observed in downstream reaches (29% of recaptures). Temporal trends and demographic patterns in movement were not observed. Because the two most downstream habitats dry up in the summer, our results indicate that coarse-scale movements that re-populate downstream reaches likely occur during other times of year. Consequently, the importance of small- and large-scale movements is influenced by season. Further assessment of Salt Creek movement patterns conducted during other times of year may better illuminate long-distance movement patterns and source-sink dynamics.

Contemporary movements and tectonics on Canada's west coast: A discussion

NASA Astrophysics Data System (ADS)

Riddihough, Robin P.

1982-06-01

Evidence from published tidal records and geodetic relevelling data in British Columbia indicates that there is a consistent pattern of contemporary uplift on the outer coast (2 mm/yr) and subsidence on the inner coast (1-2 mm/yr). The zero uplift contour or "hinge-line" runs through Hecate Strait, Georgia Strait and Victoria. This pattern continues southwards into Washington State but is interrupted to the north by considerable uplift in southeastern Alaska. Although glacio-isostatic recovery has dominated vertical movements in the region over the last 10,000 years, the distribution and trend of the observed contemporary movements are not compatible with the pattern to be expected from this source and are most probably tectonic in origin. There is, however, no clear distinction between the movements seen opposite the Queen Charlotte transform margin and the Vancouver Island convergent margin. Comparison with movements observed at other active plate margins show that the pattern is essentially similar to that seen in association with subduction and convergence. The paradox that the vertical movement rates are much too great to explain observed geology and topography may be soluble by assuming that discontinuous lateral shifts of the movement pattern occur on a scale of hundreds of thousands of years.

Independent digit movements and precision grip patterns in 1-5-month-old human infants: hand-babbling, including vacuous then self-directed hand and digit movements, precedes targeted reaching.

PubMed

Wallace, Patricia S; Whishaw, Ian Q

2003-01-01

Previous work has described human reflexive grasp patterns in early infancy and visually guided reaching and grasping in late infancy. There has been no examination of hand movements in the intervening period. This was the purpose of the present study. We video recorded the spontaneous hand and digit movements made by alert infants over their first 5 months of age. Over this period, spontaneous hand and digit movements developed from fists to almost continuous, vacuous movements and then to self-directed grasping movements. Amongst the many hand and digit movements observed, four grasping patterns emerged during this period: fists, pre-precision grips associated with numerous digit postures, precision grips including the pincer grasp, and self-directed grasps. The finding that a wide range of independent digit movements and grasp patterns are displayed spontaneously by infants within their first 5 months of age is discussed in relation to the development of the motor system, including the suggestion that direct connections of the pyramidal tract are functional relatively early in infancy. It is also suggested that hand babbling, consisting of first vacuous and then self-directed movements, is preparatory to targeted reaching.

Computer mouse movement patterns: A potential marker of mild cognitive impairment.

PubMed

Seelye, Adriana; Hagler, Stuart; Mattek, Nora; Howieson, Diane B; Wild, Katherine; Dodge, Hiroko H; Kaye, Jeffrey A

2015-12-01

Subtle changes in cognitively demanding activities occur in MCI but are difficult to assess with conventional methods. In an exploratory study, we examined whether patterns of computer mouse movements obtained from routine home computer use discriminated between older adults with and without MCI. Participants were 42 cognitively intact and 20 older adults with MCI enrolled in a longitudinal study of in-home monitoring technologies. Mouse pointer movement variables were computed during one week of routine home computer use using algorithms that identified and characterized mouse movements within each computer use session. MCI was associated with making significantly fewer total mouse moves ( p <.01), and making mouse movements that were more variable, less efficient, and with longer pauses between movements ( p <.05). Mouse movement measures were significantly associated with several cognitive domains ( p 's<.01-.05). Remotely monitored computer mouse movement patterns are a potential early marker of real-world cognitive changes in MCI.

Altered movement patterns and muscular activity during single and double leg squats in individuals with anterior cruciate ligament injury.

PubMed

Trulsson, Anna; Miller, Michael; Hansson, Gert-Åke; Gummesson, Christina; Garwicz, Martin

2015-02-13

Individuals with Anterior Cruciate Ligament (ACL) injury often show altered movement patterns, suggested to be partly due to impaired sensorimotor control. Here, we therefore aimed to assess muscular activity during movements often used in ACL-rehabilitation and to characterize associations between deviations in muscular activity and specific altered movement patterns, using and further exploring the previously developed Test for substitution Patterns (TSP). Sixteen participants (10 women) with unilateral ACL rupture performed Single and Double Leg Squats (SLS; DLS). Altered movement patterns were scored according to TSP, and Surface Electromyography (SEMG) was recorded bilaterally in six hip, thigh and shank muscles. To quantify deviations in muscular activity, SEMG ratios were calculated between homonymous muscles on injured and non-injured sides, and between antagonistic muscles on the same side. Correlations between deviations of injured/non-injured side SEMG ratios and specific altered movement patterns were calculated. Injured/non-injured ratios were low at transition from knee flexion to extension in quadriceps in SLS, and in quadriceps and hamstrings in DLS. On injured side, the quadriceps/hamstrings ratio prior to the beginning of DLS and end of DLS and SLS, and tibialis/gastrocnemius ratio at end of DLS were lower than on non-injured side. Correlations were found between specific altered movement patterns and deviating muscular activity at transition from knee flexion to extension in SLS, indicating that the more deviating the muscular activity on injured side, the more pronounced the altered movement pattern. "Knee medial to supporting foot" correlated to lower injured/non-injured ratios in gluteus medius (rs = -0.73, p = 0.001), "lateral displacement of hip-pelvis-region" to lower injured/non-injured ratios in quadriceps (rs = -0.54, p = 0.03) and "displacement of trunk" to higher injured/non-injured ratios in gluteus medius (rs = 0.62, p = 0.01). Deviations in muscular activity between injured and non-injured sides and between antagonistic muscular activity within injured as compared to non-injured sides indicated specific alterations in sensorimotor control of the lower limb in individuals with ACL rupture. Also, correlations between deviating muscular activity and specific altered movement patterns were suggested as indications of altered sensorimotor control. We therefore advocate that quantitative assessments of altered movement patterns should be considered in ACL-rehabilitation.

Phase separation driven by density-dependent movement: A novel mechanism for ecological patterns.

PubMed

Liu, Quan-Xing; Rietkerk, Max; Herman, Peter M J; Piersma, Theunis; Fryxell, John M; van de Koppel, Johan

2016-12-01

Many ecosystems develop strikingly regular spatial patterns because of small-scale interactions between organisms, a process generally referred to as spatial self-organization. Self-organized spatial patterns are important determinants of the functioning of ecosystems, promoting the growth and survival of the involved organisms, and affecting the capacity of the organisms to cope with changing environmental conditions. The predominant explanation for self-organized pattern formation is spatial heterogeneity in establishment, growth and mortality, resulting from the self-organization processes. A number of recent studies, however, have revealed that movement of organisms can be an important driving process creating extensive spatial patterning in many ecosystems. Here, we review studies that detail movement-based pattern formation in contrasting ecological settings. Our review highlights that a common principle, where movement of organisms is density-dependent, explains observed spatial regular patterns in all of these studies. This principle, well known to physics as the Cahn-Hilliard principle of phase separation, has so-far remained unrecognized as a general mechanism for self-organized complexity in ecology. Using the examples presented in this paper, we explain how this movement principle can be discerned in ecological settings, and clarify how to test this mechanism experimentally. Our study highlights that animal movement, both in isolation and in unison with other processes, is an important mechanism for regular pattern formation in ecosystems. Copyright © 2016 Elsevier B.V. All rights reserved.

21 CFR 872.4770 - Temporary mandibular condyle reconstruction plate.

Code of Federal Regulations, 2014 CFR

2014-04-01

... device that is intended to stabilize mandibular bone and provide for temporary reconstruction of the... surgical procedures requiring removal of the mandibular condyle and mandibular bone. This device is not...

The use of the mandibular infiltration anesthetic technique in adults.

PubMed

Meechan, John G

2011-09-01

The author describes the use of the infiltration anesthetic technique to anesthetize mandibular teeth in adults and explores its mechanism of action. The author reviewed articles describing randomized controlled trials of the mandibular infiltration anesthetic technique in healthy participants. The author found that using the mandibular infiltration anesthetic technique can produce anesthesia in adult mandibular teeth. The success was dose dependent and the choice of anesthetic solution was significant; 4 percent articaine with 1:100,000 epinephrine was more effective than 2 percent lidocaine with 1:100,000 epinephrine. Combining buccal and lingual infiltrations increased success in the mandibular incisor region. The success of the mechanism of infiltration of anesthetic at the mandibular first molar appeared to depend on the mental foramen. The mandibular infiltration anesthetic technique is an effective method of anesthetizing mandibular incisors. Four percent articaine with epinephrine appears to be the preferred solution. The choice of anesthetic solution is important when using the infiltration anesthetic technique in the adult mandible.

How multi segmental patterns deviate in spastic diplegia from typical developed.

PubMed

Zago, Matteo; Sforza, Chiarella; Bona, Alessia; Cimolin, Veronica; Costici, Pier Francesco; Condoluci, Claudia; Galli, Manuela

2017-10-01

The relationship between gait features and coordination in children with Cerebral Palsy is not sufficiently analyzed yet. Principal Component Analysis can help in understanding motion patterns decomposing movement into its fundamental components (Principal Movements). This study aims at quantitatively characterizing the functional connections between multi-joint gait patterns in Cerebral Palsy. 65 children with spastic diplegia aged 10.6 (SD 3.7) years participated in standardized gait analysis trials; 31 typically developing adolescents aged 13.6 (4.4) years were also tested. To determine if posture affects gait patterns, patients were split into Crouch and knee Hyperextension group according to knee flexion angle at standing. 3D coordinates of hips, knees, ankles, metatarsal joints, pelvis and shoulders were submitted to Principal Component Analysis. Four Principal Movements accounted for 99% of global variance; components 1-3 explained major sagittal patterns, components 4-5 referred to movements on frontal plane and component 6 to additional movement refinements. Dimensionality was higher in patients than in controls (p<0.01), and the Crouch group significantly differed from controls in the application of components 1 and 4-6 (p<0.05), while the knee Hyperextension group in components 1-2 and 5 (p<0.05). Compensatory strategies of children with Cerebral Palsy (interactions between main and secondary movement patterns), were objectively determined. Principal Movements can reduce the effort in interpreting gait reports, providing an immediate and quantitative picture of the connections between movement components. Copyright © 2017 Elsevier Ltd. All rights reserved.

Tc-knirps plays different roles in the specification of antennal and mandibular parasegment boundaries and is regulated by a pair-rule gene in the beetle Tribolium castaneum

PubMed Central

2013-01-01

Background The Drosophila larval head is evolutionarily derived at the genetic and morphological level. In the beetle Tribolium castaneum, development of the larval head more closely resembles the ancestral arthropod condition. Unlike in Drosophila, a knirps homologue (Tc-kni) is required for development of the antennae and mandibles. However, published Tc-kni data are restricted to cuticle phenotypes and Tc-even-skipped and Tc-wingless stainings in knockdown embryos. Hence, it has remained unclear whether the entire antennal and mandibular segments depend on Tc-kni function, and whether the intervening intercalary segment is formed completely. We address these questions with a detailed examination of Tc-kni function. Results By examining the expression of marker genes in RNAi embryos, we show that Tc-kni is required only for the formation of the posterior parts of the antennal and mandibular segments (i.e. the parasegmental boundaries). Moreover, we find that the role of Tc-kni is distinct in these segments: Tc-kni is required for the initiation of the antennal parasegment boundary, but only for the maintenance of the mandibular parasegmental boundary. Surprisingly, Tc-kni controls the timing of expression of the Hox gene Tc-labial in the intercalary segment, although this segment does form in the absence of Tc-kni function. Unexpectedly, we find that the pair-rule gene Tc-even-skipped helps set the posterior boundary of Tc-kni expression in the mandible. Using the mutant antennaless, a likely regulatory Null mutation at the Tc-kni locus, we provide evidence that our RNAi studies represent a Null situation. Conclusions Tc-kni is required for the initiation of the antennal and the maintenance of the mandibular parasegmental boundaries. Tc-kni is not required for specification of the anterior regions of these segments, nor the intervening intercalary segment, confirming that Tc-kni is not a canonical ‘gap-gene’. Our finding that a gap gene orthologue is regulated by a pair rule gene adds to the view that the segmentation gene hierarchies differ between Tribolium and Drosophila upstream of the pair rule gene level. In Tribolium, as in Drosophila, head and trunk segmentation gene networks cooperate to pattern the mandibular segment, albeit involving Tc-kni as novel component. PMID:23777260

Evaluation of total alloplastic temporo-mandibular joint replacement with two different types of prostheses: A three-year prospective study.

PubMed

Gonzalez-Perez, L-M; Gonzalez-Perez-Somarriba, B; Centeno, G; Vallellano, C; Montes-Carmona, J-F

2016-11-01

Temporo-Mandibular Joint (TMJ) replacement has been used clinically for years. The objective of this study was to evaluate outcomes achieved in patients with two different categories of TMJ prostheses. All patients who had a TMJ replacement (TMJR) implanted during the study period from 2006 through 2012 were included in this 3-year prospective study. All procedures were performed using the Biomet Microfixation TMJ Replacement System, and all involved replacing both the skull base component (glenoid fossa) and the mandibular condyle. Fifty-seven patients (38 females and 19 males), involving 75 TMJs with severe disease requiring reconstruction (39 unilateral, 18 bilateral) were operated on consecutively, and 68 stock prostheses and 7 custom-made prostheses were implanted. The mean age at surgery was 52.6±11.5 years in the stock group and 51.8±11.7 years in the custom-made group. In the stock group, after three years of TMJR, results showed a reduction in pain intensity from 6.4±1.4 to 1.6±1.2 (p<0.001), and an improvement in jaw opening from 2.7±0.9 cm to 4.2±0.7 cm (p<0.001). In the custom-made group, after three years of TMJR, results showed a reduction in pain intensity from 6.0±1.6 to 2.2±0.4 (p<0.001), and an improvement in jaw opening from 1.5±0.5 cm to 4.3±0.6 cm (p<0.001). No statistically significant differences between two groups were detected. The results of this three-year prospective study support the surgical placement of TMJ prostheses (stock prosthetic, and custom-made systems), and show that the approach is efficacious and safe, reduces pain, and improves maximum mouth opening movement, with few complications. As such, TMJR represents a viable technique and a stable long-term solution for cranio-mandibular reconstruction in patients with irreversible end-stage TMJ disease. Comparing stock and custom-made groups, no statistically significant differences were detected with respect to pain intensity reduction and maximum mouth opening improvement.

[Evaluation of the correction of the skeletal class III malocclusion by distalization of the whole mandible dentition with micro-implant anchorage].

PubMed

2017-06-18

To evaluate the clinical effect of distalizing mandibular dentition with micro-implant in patients with skeletal class III malocclusion. In the study, 20 patients with skeletal class IIImalocclusion were selected. They are consist of 8 males and 12 female with an age range from 16 to 38 years old and an average age of (21.5±5.6) years.They were treated with straight wire technique and the implant were inserted into the mandibular external oblique line to distlize the lower dentition to a class I molar relationships. Cephalometrics films were taken before and after treatment. The changes of hard tissue and soft tissue were analyzed by evaluating 26 measurement measurements. Class I molar relationships were achieved, and the profile were improved after treatment. ANB increased by (0.80±1.02) °,Wits increased by (1.67±1.74) mm,after treatment (P<0.05). The lower dentition were significantly retracted after treatment with L1-NB distance decreased by(2.64±1.50) mm, P<0.05; the mesial buccal cusp and mesial root of the lower first molars were retracted by (3.26±1.95) mm and (0.79±1.27) mm respectively (P<0.05); the mesial buccal cusp of the lower second molars were retracted by (3.06±1.80) mm (P<0.05). After treatment, mandibular teeth got up-righted distally. From incisors to molar, L1/MP, L5/MP, L6/MP, L7/MP angle decreased by (6.37±8.53)°, (10.59±8.50)°, (11.48±7.22)°, (15.72±7.16)°on average respectively (P<0.05), all of those changes had the statically significant effects. Soft tissue change after treatment, the distance from lower lip to esthetic plane were decreased by (1.70±1.59) mm on average (P<0.05). Distalizing mandibular dentition with micro-implant can get an satisfying result in patients with skeletal class III malocclusion, the lower teeth were retracted by controlled tipping movement.

Patterns, Severity, and Management of Maxillofacial Injuries in a Suburban South Western Nigeria Tertiary Center

PubMed Central

Ogunmuyiwa, Stella Aimiede; Gbolahan, Olalere Omoyosola; Ayantunde, Abiodun Abraham; Odewabi, Adenike Abidemi

2015-01-01

Background: Trauma remains a leading cause of maxillofacial injury globally. Changing etiological factors and patterns of maxillofacial injury continue to be reported and are largely modulated by socio-geographic and environmental factors. It is important to have an in-depth understanding of the pattern and etiology in a particular region before effective preventive measures can be developed. Aim: The aim was to evaluate the patterns, etiological factors, and management of maxillofacial injuries in Ogun state, Nigeria. Materials and Methods: A prospective descriptive cohort study of all consecutive patients that presented with maxillofacial injuries at our center between January and December 2013. Information about demographic data, types of maxillofacial and associated injury, etiology of injury, treatment received and complications were collected and analyzed. Results: Seventy patients presented with maxillofacial injury during the study period with a male to female ratio of 4:1. The age range was 9 months to 60 years with a mean of 30.11 ± standard deviation 14.97 years. Majority of the facial fractures were due to motorcycle related crashes. There were 57.1% mandibular fractures and 55.7% middle third fractures. Closed reduction with maxillo-mandibular fixation was the major method of treatment of facial fractures. Postoperative complications were observed in 11.4% of patients. Conclusion: Road traffic crashes (RTCs) remain the leading etiological factor of maxillofacial injuries in our center. Enforcement of stricter traffic regulations and possibly replacement of motorcycles with tricycles for commercial transportation may help to reduce the incidence of RTCs. PMID:25838765

Hoxa2 knockdown in Xenopus results in hyoid to mandibular homeosis.

PubMed

Baltzinger, Mireille; Ori, Michela; Pasqualetti, Massimo; Nardi, Irma; Rijli, Filippo M

2005-12-01

The skeletal structures of the face and throat are derived from cranial neural crest cells (NCCs) that migrate from the embryonic neural tube into a series of branchial arches (BAs). The first arch (BA1) gives rise to the upper and lower jaw cartilages, whereas hyoid structures are generated from the second arch (BA2). The Hox paralogue group 2 (PG2) genes, Hoxa2 and Hoxb2, show distinct roles for hyoid patterning in tetrapods and fishes. In the mouse, Hoxa2 acts as a selector of hyoid identity, while its paralogue Hoxb2 is not required. On the contrary, in zebrafish Hoxa2 and Hoxb2 are functionally redundant for hyoid arch patterning. Here, we show that in Xenopus embryos morpholino-induced functional knockdown of Hoxa2 is sufficient to induce homeotic changes of the second arch cartilage. Moreover, Hoxb2 is downregulated in the BA2 of Xenopus embryos, even though initially expressed in second arch NCCs, similar to mouse and unlike in zebrafish. Finally, Xbap, a gene involved in jaw joint formation, is selectively upregulated in the BA2 of Hoxa2 knocked-down frog embryos, supporting a hyoid to mandibular change of NCC identity. Thus, in Xenopus Hoxa2 does not act redundantly with Hoxb2 for BA2 patterning, similar to mouse and unlike in fish. These data bring novel insights into the regulation of Hox PG2 genes and hyoid patterning in vertebrate evolution and suggest that Hoxa2 function is required at late stages of BA2 development. Copyright 2005 Wiley-Liss, Inc.

Paresthesia during orthodontic treatment: case report and review.

PubMed

Monini, André da Costa; Martins, Renato Parsekian; Martins, Isabela Parsekian; Martins, Lídia Parsekian

2011-10-01

Paresthesia of the lower lip is uncommon during orthodontic treatment. In the present case, paresthesia occurred during orthodontic leveling of an extruded mandibular left second molar. It was decided to remove this tooth from the appliance and allow it to relapse. A reanatomization was then performed by grinding. The causes and treatment options of this rare disorder are reviewed and discussed. The main cause of paresthesia during orthodontic treatment may be associated with contact between the dental roots and inferior alveolar nerve, which may be well observed on tomography scans. Treatment usually involves tooth movement in the opposite direction of the cause of the disorder.

Remodeling of a nontreated displaced parasymphyseal fracture of a child.

PubMed

Kerem, Hakan; Usluer, Ayşen; Yoleri, Levent

2011-07-01

There have been considerable advances in the management of craniomaxillofacial injuries in children. Conservative approaches such as close observation, a liquid-to-soft diet, and analgesics can be used for the management of mandibular fractures without displacement and malocclusion. However, displaced fractures need to be an anatomic reduction and immobilization. The basic principle of displaced mandibular fractures in both children and adults is the stabilization of fracture fragments forming the pretraumatic contour and occlusion state until osteosynthesis occurs. The major differences of pediatric fractures from adults are the flexibility of bones and very rapid healing pattern. Therefore, reduction in pediatric age group must be accomplished earlier. This case was an 11-year-old boy presented with a severely displaced parasymphyseal mandibular fracture resulting from a fall. He was given a soft diet and analgesic, given anti-inflammatory treatment of edema, and scheduled for operation. Subsequently, it was surprisingly observed that there was a significant improvement in the fracture line on the 12th posttraumatic day. The comparison of maxillofacial computed tomographic scans of the first and 12th posttraumatic days revealed a noteworthy remodeling and a remarkable approximation of the fracture lines. It can be concluded that bone remodelization in the pediatric age groups is perfect and very rapid, even in severely displaced fractures.

Context-aware pattern discovery for moving object trajectories

NASA Astrophysics Data System (ADS)

Sharif, Mohammad; Asghar Alesheikh, Ali; Kaffash Charandabi, Neda

2018-05-01

Movement of point objects are highly sensitive to the underlying situations and conditions during the movement, which are known as contexts. Analyzing movement patterns, while accounting the contextual information, helps to better understand how point objects behave in various contexts and how contexts affect their trajectories. One potential solution for discovering moving objects patterns is analyzing the similarities of their trajectories. This article, therefore, contextualizes the similarity measure of trajectories by not only their spatial footprints but also a notion of internal and external contexts. The dynamic time warping (DTW) method is employed to assess the multi-dimensional similarities of trajectories. Then, the results of similarity searches are utilized in discovering the relative movement patterns of the moving point objects. Several experiments are conducted on real datasets that were obtained from commercial airplanes and the weather information during the flights. The results yielded the robustness of DTW method in quantifying the commonalities of trajectories and discovering movement patterns with 80 % accuracy. Moreover, the results revealed the importance of exploiting contextual information because it can enhance and restrict movements.

Multi-Dimensional Pattern Discovery of Trajectories Using Contextual Information

NASA Astrophysics Data System (ADS)

Sharif, M.; Alesheikh, A. A.

2017-10-01

Movement of point objects are highly sensitive to the underlying situations and conditions during the movement, which are known as contexts. Analyzing movement patterns, while accounting the contextual information, helps to better understand how point objects behave in various contexts and how contexts affect their trajectories. One potential solution for discovering moving objects patterns is analyzing the similarities of their trajectories. This article, therefore, contextualizes the similarity measure of trajectories by not only their spatial footprints but also a notion of internal and external contexts. The dynamic time warping (DTW) method is employed to assess the multi-dimensional similarities of trajectories. Then, the results of similarity searches are utilized in discovering the relative movement patterns of the moving point objects. Several experiments are conducted on real datasets that were obtained from commercial airplanes and the weather information during the flights. The results yielded the robustness of DTW method in quantifying the commonalities of trajectories and discovering movement patterns with 80 % accuracy. Moreover, the results revealed the importance of exploiting contextual information because it can enhance and restrict movements.

Head position affects the direction of occlusal force during tapping movement.

PubMed

Nakamura, K; Minami, I; Wada, J; Ikawa, Y; Wakabayashi, N

2018-05-01

Despite numerous reports describing the relationship between head position and mandibular movement in human subjects, the direction and magnitude of force at the occlusal contacts have not been investigated in relation to head position. The objective was to investigate the effect of head position on the direction of occlusal force while subjects performed a tapping movement. Twenty-three healthy adult subjects were asked to sit on a chair with their back upright and to perform 15 tapping movements in five different head positions: natural head position (control); forward; backward; and right and left rolled. The direction and magnitude of force were measured using a small triaxial force sensor. The Wilcoxon signed-rank test and Bonferroni test were used to compare head positions in each angle of the anteroposterior axis direction and the lateral axis direction with respect to the superior axis. The force element in the anteroposterior axis shifted to the forward direction in the head position pitched backward, compared with control, pitched forward and rolled left positions (P = .02, <.01 and <.01, respectively). The force direction in the lateral axis with the head position rolled to the right or left shifted to the left and right directions, respectively, compared with those in the other positions (P < .05). Results of this study suggest that the head should be maintained in a position in which a stable tapping movement can be performed in a relaxed position without anteroposterior and lateral loading. © 2018 John Wiley & Sons Ltd.

Morphometric study on mandibular foramen and incidence of accessory mandibular foramen in mandibles of south Indian population and its clinical implications in inferior alveolar nerve block.

PubMed

Shalini, R; RaviVarman, C; Manoranjitham, R; Veeramuthu, M

2016-12-01

The mandibular foramen is a landmark for procedures like inferior alveolar nerve block, mandibular implant treatment, and mandibular osteotomies. The present study was aimed to identify the precise location of the mandibular foramen and the incidence of accessory mandibular foramen in dry adult mandibles of South Indian population. The distance of mandibular foramen from the anterior border of the ramus, posterior border of the ramus, mandibular notch, base of the mandible, third molar, and apex of retromolar trigone was measured with a vernier caliper in 204 mandibles. The mean distance of mandibular foramen from the anterior border of ramus of mandible was 17.11±2.74 mm on the right side and 17.41±3.05 mm on the left side, from posterior border was 10.47±2.11 mm on the right side and 9.68±2.03 mm on the left side, from mandibular notch was 21.74±2.74 mm on the right side and 21.92±3.33 mm on the left side, from the base of the ramus was 22.33±3.32 mm on the right side and 25.35±4.5 mm on the left side, from the third molar tooth was 22.84±3.94 mm on the right side and 23.23±4.21 mm on the left side, from the apex of retromolar trigone was 12.27±12.13 mm on the right side and 12.13±2.35 mm on the left side. Accessory mandibular foramen was present in 32.36% of mandibles. Knowledge of location mandibular foramen is useful to the maxillofacial surgeons, oncologists and radiologists.

Morphometric study on mandibular foramen and incidence of accessory mandibular foramen in mandibles of south Indian population and its clinical implications in inferior alveolar nerve block

PubMed Central

RaviVarman, C.; Manoranjitham, R.; Veeramuthu, M.

2016-01-01

The mandibular foramen is a landmark for procedures like inferior alveolar nerve block, mandibular implant treatment, and mandibular osteotomies. The present study was aimed to identify the precise location of the mandibular foramen and the incidence of accessory mandibular foramen in dry adult mandibles of South Indian population. The distance of mandibular foramen from the anterior border of the ramus, posterior border of the ramus, mandibular notch, base of the mandible, third molar, and apex of retromolar trigone was measured with a vernier caliper in 204 mandibles. The mean distance of mandibular foramen from the anterior border of ramus of mandible was 17.11±2.74 mm on the right side and 17.41±3.05 mm on the left side, from posterior border was 10.47±2.11 mm on the right side and 9.68±2.03 mm on the left side, from mandibular notch was 21.74±2.74 mm on the right side and 21.92±3.33 mm on the left side, from the base of the ramus was 22.33±3.32 mm on the right side and 25.35±4.5 mm on the left side, from the third molar tooth was 22.84±3.94 mm on the right side and 23.23±4.21 mm on the left side, from the apex of retromolar trigone was 12.27±12.13 mm on the right side and 12.13±2.35 mm on the left side. Accessory mandibular foramen was present in 32.36% of mandibles. Knowledge of location mandibular foramen is useful to the maxillofacial surgeons, oncologists and radiologists. PMID:28127498

The efficacy of supplemental intraosseous anesthesia after insufficient mandibular block.

PubMed

Prohić, Samir; Sulejmanagić, Halid; Secić, Sadeta

2005-02-01

It is a well-known scientific fact that only a small percentage of infiltration of inferior alveolar nerve is clinically proven to be efficient. The objective of this study was to determine the anesthetic efficacy of supplemental intraosseous injection, used after the insufficient classical mandibular block that didn't provide deep pulp anesthesia of mandibular molar planed for extraction. The experimental teeth consisted of 98 mandibular molars with clinical indication for extraction. Based on the history of disease, we indicated the extraction of the tooth. After that each tooth was tested with a electric pulp tester P1. We tested the pulp vitality and precisely determined the level of vitality. After that, each patient received classical mandibular block, and the pulp vitality was tested again. If the pulp tester indicated negative vitality for the certain mandibular molar, and the patient didn't complain about pain or discomfort during the extraction, the molar was extracted and the result was added to anesthetic success rate for the classical mandibular block. If, five minutes after receiving the mandibular block, the pulp tester indicated positive vitality (parameters of vitality) or the patient complained about pain or discomfort (parameters of pain and discomfort), we used the Stabident intraosseous anesthesia system. Three minutes after the application of supplemental intraosseous injection the molar was tested with the pulp tester again. The anesthetic solution used in both anesthetic techniques is lidocaine with 1:100.000 epinephrine. The results of this study indicate that the anesthetic efficacy of the mandibular block is 74.5%, and that supplemental intraosseous anesthesia, applied after the insufficient mandibular block, provides pulpal anesthesia in 94.9% of mandibular molars. The difference between anesthetic efficacy of the classical mandibular block and anesthetic efficacy of the supplemental intraosseous anesthesia, applied after the insufficient mandibular block, is obvious.

Unilateral posterior crossbite and mastication.

PubMed

Rilo, Benito; da Silva, José Luis; Mora, María Jesús; Cadarso-Suárez, Carmen; Santana, Urbano

2007-05-01

This study was designed to characterize masticatory-cycle morphology, and distance of the contact glide in the closing masticatory stroke, in adult subjects with uncorrected unilateral posterior crossbite (UPXB), comparing the results obtained with those obtained in a parallel group of normal subjects. Mandibular movements (masticatory movements and laterality movements with dental contact) were registered using a gnathograph (MK-6I Diagnostic System) during unilateral chewing of a piece of gum. Traces were recorded on the crossbite and non-crossbite sides in the crossbite group, and likewise on both sides in the non-crossbite group. Mean contact glide distance on the crossbite side in the UPXB group was significantly lower than in the control group (p<0.001), and mean contact glide distance on the non-crossbite side in the UPXB group was significantly lower than in the control group (p=0.042). Cycle morphology was abnormal during chewing on the crossbite side, with the frequency distribution of cycle types differing significantly from that for the noncrossbite side and that for the control group (p<0.001). Patients with crossbite showed alterations in both contact glide distances and masticatory cycle morphology. These alterations are probably adaptive responses allowing maintenance of adequate masticatory function despite the crossbite.

Long-term treatment effects of the FR-2 appliance: a prospective evalution 7 years post-treatment

PubMed Central

Franchi, Lorenzo; Cevidanes, Lucia H. S.; Scanavini, Marco A.; McNamara, James A.

2014-01-01

AIM To examine the long-term effects induced by treatment with the function regulator (FR-2) appliance 7 years post-treatment compared with untreated class II subjects. SUBJECTS AND METHODS The FR-2 sample was collected prospectively and comprised 17 subjects (10 boys and 7 girls, mean age 10.8 years) who were treated with the FR-2 appliance for 1.7 years and re-evaluated 7.1 years after treatment. The step-by-step mandibular advancement was performed gradually (increments up to 3–4 mm), until a ‘super class I’ molar relationship was obtained. The control group consisted of 17 class II subjects (9 boys and 8 girls, mean age 11.3 years) with class II malocclusion, excessive overjet, and class II molar relationship, matched to the treated group as to ages at all times, gender distribution, and stages of skeletal maturity (evaluated by the cervical vertebral maturation method). The lateral cephalograms were analysed at T1 (initial), T2 (final), and T3 (7.1 years post-treatment). The compatibility between the groups and the comparisons of their changes at T1–T2, T2–T3, and T1–T3 intervals were examined by independent sample t-tests (P < 0.05). RESULTS FR-2 treatment provided a significant improvement in the maxillomandibular relationship due to an increase in mandibular length compared with controls, which remained stable over time. Also overjet, overbite, and molar relationship corrections demonstrated stability. Among dentoalveolar changes, only the increased mesial movement of the mandibular molars in the FR-2 group demonstrated stability. CONCLUSIONS Correction of class II malocclusion remained stable 7 years after FR-2 treatment mainly due to the stability of the skeletal changes. PMID:23736378

Soft tissue changes and its stability as a sequlae to mandibular advancement

PubMed Central

Uppada, Uday Kiran; Sinha, Ramen; Reddy, D. Sreenatha; Paul, Dushyanth

2014-01-01

Purpose of the Study: To predict the changes and evaluate the stability that occurs in the soft tissues following the skeletal movement subsequent to surgical advancement of the mandible through bilateral sagittal split osteotomy and to provide the patient reliable information with regard to esthetic changes that can be expected following the treatment. Materials and Methods: Twenty adult patients diagnosed with skeletal class II malocclusion and underwent bilateral sagittal split osteotomy for mandibular advancement by a mean of 8 mm using rigid fixation were included in the study. Soft tissue changes brought about by the surgical procedure and their stability over a period of time were evaluated prospectively using 12 linear (4 vertical and 8 horizontal) and 4 angular measurements on profile cephalograms which were taken preoperatively after the pre-surgical orthodontics (T1) and postoperatively with duration of 1 month (T2) and 6 months (T3) respectively. Results: It was observed that compared to the linear measurements, the angular measurements showed significant changes. The improvement in the esthetic outcome is a direct reflection of the angular changes whereas the linear changes played a contributing role. Following mandibular advancement surgery the profiles of the patients was perceived to have improved with reduction in the facial convexity, an increase in the lower facial height, decrease in the depth of the mentolabial sulcus and improvement in the lip competency with lengthening, straightening and thinning of the lower lip. Conclusion: The soft tissue response and its stability depends on the stability of the surgical procedure itself, postsurgical growth and remodeling of the hard tissues and soft tissue changes as a result of maturation and aging. PMID:25593860

Orthodontic retreatment using anchorage with miniplate to camouflage a Class III skeletal pattern.

PubMed

Farret, Marcel Marchiori

2016-06-01

This manuscript describes the treatment of a 27-year-old patient who was previously treated with two maxillary first premolar extractions. The patient had skeletal Class III malocclusion, Class III canine relationship, anterior crossbite, and a concave profile. As the patient refused orthognathic surgery, a miniplate was used on the right side of the lower arch as an anchorage unit after the extraction of mandibular first premolars, aiding the retraction of anterior teeth. At the end of treatment, anterior crossbite was corrected, in which first molars and canines were in a Class I relationship, and an excellent intercuspation was reached. Furthermore, patient's profile remarkably improved as a result of mandibular incisor retraction. A 30-month follow-up showed good stability of the results obtained. This case was presented to the Brazilian Board of Orthodontics and Dentofacial Orthopedics (BBO) as one of the requirements to become diplomate by the BBO.

Orthodontic retreatment using anchorage with miniplate to camouflage a Class III skeletal pattern

PubMed Central

Farret, Marcel Marchiori

2016-01-01

ABSTRACT This manuscript describes the treatment of a 27-year-old patient who was previously treated with two maxillary first premolar extractions. The patient had skeletal Class III malocclusion, Class III canine relationship, anterior crossbite, and a concave profile. As the patient refused orthognathic surgery, a miniplate was used on the right side of the lower arch as an anchorage unit after the extraction of mandibular first premolars, aiding the retraction of anterior teeth. At the end of treatment, anterior crossbite was corrected, in which first molars and canines were in a Class I relationship, and an excellent intercuspation was reached. Furthermore, patient's profile remarkably improved as a result of mandibular incisor retraction. A 30-month follow-up showed good stability of the results obtained. This case was presented to the Brazilian Board of Orthodontics and Dentofacial Orthopedics (BBO) as one of the requirements to become diplomate by the BBO. PMID:27409659

Exploratory Movement Generates Higher-Order Information That Is Sufficient for Accurate Perception of Scaled Egocentric Distance

PubMed Central

Mantel, Bruno; Stoffregen, Thomas A.; Campbell, Alain; Bardy, Benoît G.

2015-01-01

Body movement influences the structure of multiple forms of ambient energy, including optics and gravito-inertial force. Some researchers have argued that egocentric distance is derived from inferential integration of visual and non-visual stimulation. We suggest that accurate information about egocentric distance exists in perceptual stimulation as higher-order patterns that extend across optics and inertia. We formalize a pattern that specifies the egocentric distance of a stationary object across higher-order relations between optics and inertia. This higher-order parameter is created by self-generated movement of the perceiver in inertial space relative to the illuminated environment. For this reason, we placed minimal restrictions on the exploratory movements of our participants. We asked whether humans can detect and use the information available in this higher-order pattern. Participants judged whether a virtual object was within reach. We manipulated relations between body movement and the ambient structure of optics and inertia. Judgments were precise and accurate when the higher-order optical-inertial parameter was available. When only optic flow was available, judgments were poor. Our results reveal that participants perceived egocentric distance from the higher-order, optical-inertial consequences of their own exploratory activity. Analysis of participants’ movement trajectories revealed that self-selected movements were complex, and tended to optimize availability of the optical-inertial pattern that specifies egocentric distance. We argue that accurate information about egocentric distance exists in higher-order patterns of ambient energy, that self-generated movement can generate these higher-order patterns, and that these patterns can be detected and used to support perception of egocentric distance that is precise and accurate. PMID:25856410

Retention of movement pattern changes after a lower extremity injury prevention program is affected by program duration.

PubMed

Padua, Darin A; DiStefano, Lindsay J; Marshall, Stephen W; Beutler, Anthony I; de la Motte, Sarah J; DiStefano, Michael J

2012-02-01

Changes in movement patterns have been repeatedly observed immediately after completing a lower extremity injury prevention program. However, it is not known if movement pattern changes are maintained after discontinuing the training program. The ability to maintain movement pattern changes after training has ceased may be influenced by the program's duration. The authors hypothesized that among individuals who completed either a 3-month or 9-month training program and who demonstrated immediate movement pattern changes, only those who completed the 9-month training program would maintain movement pattern changes after a 3-month period of no longer performing the exercises. Cohort study; Level of evidence, 2. A total of 140 youth soccer athletes from 15 separate teams volunteered to participate. Athletes' movement patterns were assessed using the Landing Error Scoring System (LESS) at pretest, posttest, and 3 months after ceasing the program (retention test). Eighty-four of the original 140 participants demonstrated improvements in their LESS scores between pretest and posttest (change in LESS score >0) and were included in the final analyses for this study (n = 84; 20 boys and 64 girls; mean age, 14 ± 2 years; age range, 11-17 years). Teams performed 3-month (short-duration group) and 9-month (extended-duration group) injury prevention programs. The exercises performed were identical for both groups. Teams performed the programs as part of their normal warm-up routine. Although both groups improved their total LESS scores from pretest to posttest, only the extended-duration training group retained their improvements 3 months after ceasing the injury prevention program (F(2,137) = 3.38; P = .04). Results suggest that training duration may be an important factor to consider when designing injury prevention programs that facilitate long-term changes in movement control.

Exploring patterns of movement suspension in pedestrian mobility.

PubMed

Orellana, Daniel; Wachowicz, Monica

2011-01-01

One of the main tasks in analyzing pedestrian movement is to detect places where pedestrians stop, as those places usually are associated with specific human activities, and they can allow us to understand pedestrian movement behavior. Very few approaches have been proposed to detect the locations of stops in positioning data sets, and they often are based on selecting the location of candidate stops as well as potential spatial and temporal thresholds according to different application requirements. However, these approaches are not suitable for analyzing the slow movement of pedestrians where the inaccuracy of a nondifferential global positioning system commonly used for movement tracking is so significant that it can hinder the selection of adequate thresholds. In this article, we propose an exploratory statistical approach to detect patterns of movement suspension using a local indicator of spatial association (LISA) in a vector space representation. Two different positioning data sets are used to evaluate our approach in terms of exploring movement suspension patterns that can be related to different landscapes: players of an urban outdoor mobile game and visitors of a natural park. The results of both experiments show that patterns of movement suspension were located at places such as checkpoints in the game and different attractions and facilities in the park. Based on these results, we conclude that using LISA is a reliable approach for exploring movement suspension patterns that represent the places where the movement of pedestrians is temporally suspended by physical restrictions (e.g., checkpoints of a mobile game and the route choosing points of a park).

Losing dexterity: patterns of impaired coordination of finger movements in musician’s dystonia

PubMed Central

Furuya, Shinichi; Tominaga, Kenta; Miyazaki, Fumio; Altenmüller, Eckart

2015-01-01

Extensive training can bring about highly-skilled action, but may also impair motor dexterity by producing involuntary movements and muscular cramping, as seen in focal dystonia (FD) and tremor. To elucidate the underlying neuroplastic mechanisms of FD, the present study addressed the organization of finger movements during piano performance in pianists suffering from the condition. Principal component (PC) analysis identified three patterns of fundamental joint coordination constituting finger movements in both patients and controls. The first two coordination patterns described less individuated movements between the “dystonic” finger and key-striking fingers for patients compared to controls. The third coordination pattern, representing the individuation of movements between the middle and ring fingers, was evident during a sequence of strikes with these fingers in controls, which was absent in the patients. Consequently, rhythmic variability of keystrokes was more pronounced during this sequence of strikes for the patients. A stepwise multiple-regression analysis further identified greater variability of keystrokes for individuals displaying less individuated movements between the affected and striking fingers. The findings suggest that FD alters dexterous joint coordination so as to lower independent control of finger movements, and thereby degrades fine motor control. PMID:26289433

Evaluation of the Transverse Displacement of the Proximal Segment After Bilateral Sagittal Split Ramus Osteotomy With Different Lingual Split Patterns and Advancement Amounts Using the Finite Element Method.

PubMed

Dai, Zhi; Hou, Min; Ma, Wen; Song, Da-Li; Zhang, Chun-Xiang; Zhou, Wei-Yuan

2016-11-01

To evaluate transverse displacement of the proximal segment after bilateral sagittal split ramus osteotomy (BSSO) advancement with different lingual split patterns and advancement amounts and to determine the influential factors related to mandibular width. A 3-dimensional finite element model of the mandible including the temporomandibular joint was created for a presurgical simulation and for BSSO with lingual split patterns I (T1; Hunsuck split) and II (T2; Obwegeser split). The mandible was advanced 3 mm (A3) and 8 mm (A8) and fixated with a conventional titanium plate. Ansys software was used to measure the linear distances of the interproximal segments and to analyze the transverse displacement distribution of proximal segments after applying the load of masticatory muscle force groups. After surgical simulation, T1A3, T1A8, T2A3, and T2A8 showed increased transverse widths (mean, 2.99, 4.70, 2.36, and 4.42 mm, respectively). For transverse augmentation, there was a statistically significant difference between the 2 different mandibular advancement amounts in T1 and in T2 (P ≤ .000), but no significant differences was observed between T1 and T2 (P ≥ .058). The maximum transverse displacement distribution in the proximal segment was measured around the gonial area, and the early contact area was found near the border between the horizontal and sagittal osteotomy lines. Transverse displacements of proximal segments occur after BSSO advancement with T1 and T2 and transverse augmentation has statistically meaningful effects depending on the amount of advancement; however, no differences in transverse augmentation between T1 and T2 were identified. The fulcrum caused by the early contact between the proximal and distal segments could be an influential factor related to mandibular width. Copyright © 2016 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Long Term Stability and Relapse Following Mandibular Advancement and Mandibular Setback Surgeries: A Cephalometric Study

PubMed Central

Darshan, S Vinay; Ronad, Yusuf Ahammed; Kishore, M S V; Shetty, K Sadashiva; Rajesh, M; Suman, S D

2014-01-01

Background: The aim was to evaluate the long-term hard and soft tissue changes following mandibular advancement and setback surgeries. Materials and Methods: A total of 16 subjects each were selected who underwent bilateral sagittal split osteotomy mandibular advancement and mandibular setback groups. Pre-surgical (T1), immediate post-surgical (T2) and long-term post-surgical (T3) cephalograms were compared for hard and soft tissue changes. After cephalometric measurements, the quantity of changes between T1-T2 and T1-T3 were determined for each patient. The mean difference between T1-T2 and T1-T3 was compared with assess the long-term changes and stability. Results: In mandibular advancement the mean difference between immediate post-surgical and long term post-surgical is 7%, which accounts for a relapse of 7%. In mandibular setback, the mean difference between immediate post-surgical and long-term post-surgical is 29%, which accounts for a relapse of 29%. Conclusion: Mandibular advancement remained stable over the long period when compared to mandibular setback. PMID:25395792

Long term stability and relapse following mandibular advancement and mandibular setback surgeries: a cephalometric study.

PubMed

Darshan, S Vinay; Ronad, Yusuf Ahammed; Kishore, M S V; Shetty, K Sadashiva; Rajesh, M; Suman, S D

2014-09-01

The aim was to evaluate the long-term hard and soft tissue changes following mandibular advancement and setback surgeries. A total of 16 subjects each were selected who underwent bilateral sagittal split osteotomy mandibular advancement and mandibular setback groups. Pre-surgical (T1), immediate post-surgical (T2) and long-term post-surgical (T3) cephalograms were compared for hard and soft tissue changes. After cephalometric measurements, the quantity of changes between T1-T2 and T1-T3 were determined for each patient. The mean difference between T1-T2 and T1-T3 was compared with assess the long-term changes and stability. In mandibular advancement the mean difference between immediate post-surgical and long term post-surgical is 7%, which accounts for a relapse of 7%. In mandibular setback, the mean difference between immediate post-surgical and long-term post-surgical is 29%, which accounts for a relapse of 29%. Mandibular advancement remained stable over the long period when compared to mandibular setback.

A prospective study of mandibular trabecular bone to predict fracture incidence in women: a low-cost screening tool in the dental clinic.

PubMed

Jonasson, Grethe; Sundh, Valter; Ahlqwist, Margareta; Hakeberg, Magnus; Björkelund, Cecilia; Lissner, Lauren

2011-10-01

Bone structure is the key to the understanding of fracture risk. The hypothesis tested in this prospective study is that dense mandibular trabeculation predicts low fracture risk, whereas sparse trabeculation is predictive of high fracture risk. Out of 731 women from the Prospective Population Study of Women in Gothenburg with dental examinations at baseline 1968, 222 had their first fracture in the follow-up period until 2006. Mandibular trabeculation was defined as dense, mixed dense plus sparse, and sparse based on panoramic radiographs from 1968 and/or 1980. Time to fracture was ascertained and used as the dependent variable in three Cox proportional hazards regression analyses. The first analysis covered 12 years of follow-up with self-reported endpoints; the second covered 26 years of follow-up with hospital verified endpoints; and the third combined the two follow-up periods, totaling 38 years. Mandibular trabeculation was the main independent variable predicting incident fractures, with age, physical activity, alcohol consumption and body mass index as covariates. The Kaplan-Meier curve indicated a graded association between trabecular density and fracture risk. During the whole period covered, the hazard ratio of future fracture for sparse trabeculation compared to mixed trabeculation was 2.9 (95% CI: 2.2-3.8, p<0.0001), and for dense versus mixed trabeculation was 0.21 (95% CI: 0.1-0.4, p<0.0001). The trabecular pattern was a highly significant predictor of future fracture risk. Our findings imply that dentists, using ordinary dental radiographs, can identify women at high risk for future fractures at 38-54 years of age, often long before the first fracture occurs. Copyright © 2011 Elsevier Inc. All rights reserved.

Evaluation of arch width variations among different skeletal patterns in South Indian population

PubMed Central

Prasad, Mandava; Kannampallil, Senny Thomas; Talapaneni, Ashok Kumar; George, Suja Ani; Shetty, Sharath Kumar

2013-01-01

Background: Anterior cranial base can be taken as a reference line (SN) to determine the steepness of mandibular plane. Subjects with high mandibular plane angle tend to have a long face and one with low MP-SN angle has a shorter face. Objective: This study was done to investigate if dental arch widths correlated with vertical facial types and if there are any differences in arch widths between untreated male and female adults in South Indian population. Materials and Methods: Lateral cephalogram and dental casts were obtained from 180 untreated South Indian adults (90 males and 90 females) above 18 year old with no cross bite, minimal crowding and spacing. The angle between the anterior cranial base and the mandibular plane was measured on lateral cephalogram of each patient. Dental casts were used to obtain comprehensive dental measurements including maxillary and mandibular inter canine, inter premolar and inter molar widths, as well as amount of crowding or spacing. Results: The results showed that male arch widths were significantly larger than those of females (P < 0.05) and there was a significant decrease in inter arch width as the MP-SN angle increased in untreated adult South Indian population. The results obtained in our study when compared with studies done in other population groups showed that there is difference in inter arch widths according to ethnicity and race. Conclusion: It was concluded that the dental arch width is associated with gender, race and vertical facial morphology. Thus using individualized arch wires according to each patient's pre treatment arch form and width is suggested during orthodontic treatment. PMID:23633842

Study between anb angle and wits appraisal in cone beam computed tomography (cbct)

PubMed Central

Cibrián, Rosa; Gandia, Jose L.; Paredes, Vanessa

2013-01-01

Objectives: To analyse the ANB and Wits values and to study correlations between those two measurements and other measurements in diagnosing the anteroposterior maxilo-mandibular relationship with CBCT. Study Design: Ninety patients who had previously a CBCT (i-CAT®) as a diagnostic register were selected. A 3D cephalometry was designed using one software package, InVivo5®. This cephalometry included 3 planes of reference, 3 angle measurements and 1 linear measurement. The means and standard deviations of the mean of each measurement were assessed. After that, a Pearson´s correlation coefficient has been performed to analyse the significance of each relationship. Results: When classifying the sample according to the anteroposterior relationship, the values obtained of ANB (Class I: 53%; Class II: 37%; Class III: 10%) and Wits (Class I: 35%; Class II: 56%; Class III: 9%) did not coincide, except for the Class III group. However, of the patients classified differently (Class I and Class II patients) by ANB and Wits, a high percentage of individuals (n=22; 49%), had a mesofacial pattern with a mandibular plane angle within normal values. A correlation has been found between ANB and Wits (r=0,262), occlusal plane angle and ANB (r=0,426), and mandibular plane angle and Wits (r=0,242). No correlation was found between either Wits or ANB in relation with the age of the individuals. Conclusions: ANB and Wits must be included in 3D cephalometric analyses as both are necessary to undertake a more accurate diagnosis of the maxillo-mandibular relationship of the patients. Key words:Cone beam computed tomography, ANB, Wits, cephalometrics. PMID:23722136

Cephalometric Evaluation of Children with Allergic Rhinitis and Mouth Breathing.

PubMed

Agostinho, Helena Afonso; Furtado, Ivo Ãlvares; Silva, Francisco Salvado; Ustrell Torrent, Josep

2015-01-01

Orthodontists frequently treat children with mouth breathing. The purpose of the present study was to examine dental positions, skeletal effects and the pharyngeal airway space of children with chronic allergic rhinitis, when compared with a control group exhibiting a normal breathing pattern. Seventy Caucasian children from Santa Maria University Hospital - North Lisbon Hospital Center were evaluated, between September 2009 and February 2013. The study group comprised of 35 children with chronic allergic rhinitis, both genders, aged 5 - 14, with positive reaction to allergens, mouth breathing and malocclusion. The control group was composed of 35 children, both genders, displaying normal nasal breathing and malocclusion, who resorted to the orthodontic department. Measures of Ricketts, Steiner and McNamara's analysis were used and the t- Student test was applied to the data obtained. Statistically significant differences were observed between the oral and nasal breathers, respectively: lower facial height (49.1/45.9 mm), Frankfurt â mandibular plane angle (30.1/26.9º) and Sela-Nasion - oclusal plane angle (17.3/15º), maxillary length (78.4/82.4 mm), mandibular length (102.4/107 mm), overbite (0.8/3.1mm) and overjet (4/4.7 mm). Comparison between the allergic rhinitis and control group showed that there is an increased lower facial height, larger Frankfurt â mandibular plane angle and Sela-Nasion oclusal plane angle in children with chronic allergic rhinitis. This group also had a shorter maxillary and mandibular length, less overbite and decreased upper airway space. Children with allergic rhinitis and mouth breathing have longer faces, shorter maxillas and mandibles and a narrowed pharyngeal airway space. No statistical differences between the groups in sagital relationships or in dental inclinations were found.

Pediatric facial injuries: It's management

PubMed Central

Singh, Geeta; Mohammad, Shadab; Pal, U. S.; Hariram; Malkunje, Laxman R.; Singh, Nimisha

2011-01-01

Background: Facial injuries in children always present a challenge in respect of their diagnosis and management. Since these children are of a growing age every care should be taken so that later the overall growth pattern of the facial skeleton in these children is not jeopardized. Purpose: To access the most feasible method for the management of facial injuries in children without hampering the facial growth. Materials and Methods: Sixty child patients with facial trauma were selected randomly for this study. On the basis of examination and investigations a suitable management approach involving rest and observation, open or closed reduction and immobilization, trans-osseous (TO) wiring, mini bone plate fixation, splinting and replantation, elevation and fixation of zygoma, etc. were carried out. Results and Conclusion: In our study fall was the predominant cause for most of the facial injuries in children. There was a 1.09% incidence of facial injuries in children up to 16 years of age amongst the total patients. The age-wise distribution of the fracture amongst groups (I, II and III) was found to be 26.67%, 51.67% and 21.67% respectively. Male to female patient ratio was 3:1. The majority of the cases of facial injuries were seen in Group II patients (6-11 years) i.e. 51.67%. The mandibular fracture was found to be the most common fracture (0.60%) followed by dentoalveolar (0.27%), mandibular + midface (0.07) and midface (0.02%) fractures. Most of the mandibular fractures were found in the parasymphysis region. Simple fracture seems to be commonest in the mandible. Most of the mandibular and midface fractures in children were amenable to conservative therapies except a few which required surgical intervention. PMID:22639504

Pediatric facial injuries: It's management.

PubMed

Singh, Geeta; Mohammad, Shadab; Pal, U S; Hariram; Malkunje, Laxman R; Singh, Nimisha

2011-07-01

Facial injuries in children always present a challenge in respect of their diagnosis and management. Since these children are of a growing age every care should be taken so that later the overall growth pattern of the facial skeleton in these children is not jeopardized. To access the most feasible method for the management of facial injuries in children without hampering the facial growth. Sixty child patients with facial trauma were selected randomly for this study. On the basis of examination and investigations a suitable management approach involving rest and observation, open or closed reduction and immobilization, trans-osseous (TO) wiring, mini bone plate fixation, splinting and replantation, elevation and fixation of zygoma, etc. were carried out. In our study fall was the predominant cause for most of the facial injuries in children. There was a 1.09% incidence of facial injuries in children up to 16 years of age amongst the total patients. The age-wise distribution of the fracture amongst groups (I, II and III) was found to be 26.67%, 51.67% and 21.67% respectively. Male to female patient ratio was 3:1. The majority of the cases of facial injuries were seen in Group II patients (6-11 years) i.e. 51.67%. The mandibular fracture was found to be the most common fracture (0.60%) followed by dentoalveolar (0.27%), mandibular + midface (0.07) and midface (0.02%) fractures. Most of the mandibular fractures were found in the parasymphysis region. Simple fracture seems to be commonest in the mandible. Most of the mandibular and midface fractures in children were amenable to conservative therapies except a few which required surgical intervention.

Interspecies difference in placement of developing teeth and its relationship with cross-sectional geometry of the mandibular symphysis in four primate species including modern humans.

PubMed

Fukase, Hitoshi

2012-02-01

The form of the anthropoid mandibular symphysis has recently been addressed in association with spatial requirements for the forming anterior teeth. To evaluate potential relationships between the symphyseal shape and teeth further, the growth patterns of the symphyseal region and the positioning of the tooth crypts were examined using CT data, comparing four primate species (modern humans, chimpanzees, Japanese monkeys, and hamadryas baboons) with varied symphyseal curvature and tooth size. First, results showed that interspecies differences in overall mandibular shape including symphyseal inclination and bicanine width are consistently expressed throughout postnatal ontogeny, although local symphyseal configurations related to the superior transverse torus (STT) tended to change considerably during growth in chimpanzees. Second, the four species were found to exhibit differentiated formation positions of the incisor and canine crypts. In particular, I2 developed between I1 and C in humans with a broad bicanine space and small teeth, whereas it was positioned posterior to I1 and above C in the cercopithecines with an extremely narrow bicanine space. In chimpanzees, despite the large bicanine width, I1 and I2 grew with a large antero-posterior overlap owing to their large size. These results indicate that the dental positioning is determined in concert with the size balance of the available mandibular space and forming teeth. Finally, the positions/contours of I2 crypt were shown to correspond strongly with the STT across the taxa. This suggests that interspecies differences in symphyseal shape should be interpreted partially by the species-specific positional relationships of the developing anterior teeth. Copyright © 2011 Wiley Periodicals, Inc.

The usefulness of GPS telemetry to study wolf circadian and social activity

USGS Publications Warehouse

Merrill, S.B.; David, Mech L.

2003-01-01

This study describes circadian and social movement patterns of 9 wolves and illustrates capabilities and limitations of Global Positioning System (GPS) telemetry for analysis of animal activity patterns. Wolves were studied at the Camp Ripley National Guard Training Site in Little Falls, Minnesota, and were captured via helicopter net-gunning. All study wolves showed nocturnal movement patterns regardless of time of year. One wolf's movement pattern switched to diurnal when he conducted an extraterritorial foray from his natal territory. All data sets with GPS intervals ???1 hour (n = 4) showed crepuscular movement peaks. We identified patterns of den visitation and attendance, estimated minimum distances traveled and minimum rates of movement, and observed that GPS location intervals may affect perceived rates of wolf travel. Global Positioning System telemetry was useful in determining when pack members were traveling together or apart and how long a breeding female wolf spent near her pups (e.g., 10-month-old pups were left unattended by their mother for as long as 17 days).

Passive Transport Disrupts Grid Signals in the Parahippocampal Cortex.

PubMed

Winter, Shawn S; Mehlman, Max L; Clark, Benjamin J; Taube, Jeffrey S

2015-10-05

Navigation is usually thought of relative to landmarks, but neural signals representing space also use information generated by an animal's movements. These signals include grid cells, which fire at multiple locations, forming a repeating grid pattern. Grid cell generation depends upon theta rhythm, a 6-10 Hz electroencephalogram (EEG) oscillation that is modulated by the animals' movement velocity. We passively moved rats in a clear cart to eliminate motor related self-movement cues that drive moment-to-moment changes in theta rhythmicity. We found that passive movement maintained theta power and frequency at levels equivalent to low active movement velocity, spared overall head-direction (HD) cell characteristics, but abolished both velocity modulation of theta rhythmicity and grid cell firing patterns. These results indicate that self-movement motor cues are necessary for generating grid-specific firing patterns, possibly by driving velocity modulation of theta rhythmicity, which may be used as a speed signal to generate the repeating pattern of grid cells. Copyright © 2015 Elsevier Ltd. All rights reserved.

Passive Transport Disrupts Grid Signals in the Parahippocampal Cortex

PubMed Central

Winter, Shawn S.; Mehlman, Max L.; Clark, Benjamin J.; Taube, Jeffrey S.

2015-01-01

Summary Navigation is usually thought of relative to landmarks, but neural signals representing space also use information generated by an animal’s movements. These signals include grid cells, which fire at multiple locations forming a repeating grid pattern. Grid cell generation depends upon theta rhythm, a 6-10 Hz EEG oscillation that is modulated by the animals’ movement velocity. We passively moved rats in a clear cart to eliminate motor related self-movement cues that drive moment-to-moment changes in theta rhythmicity. We found that passive movement maintained theta power and frequency at levels equivalent to low active movement velocity, spared overall HD cell characteristics, and abolished velocity modulation of theta rhythmicity and grid cell firing patterns. These results indicate that self-movement motor cues are necessary for generating grid-specific firing patterns, possibly by driving velocity modulation of theta rhythmicity. Velocity modulation of theta may be used as a speed signal to generate the repeating pattern of grid cells. PMID:26387719

Time series association learning

DOEpatents

Papcun, George J.

1995-01-01

An acoustic input is recognized from inferred articulatory movements output by a learned relationship between training acoustic waveforms and articulatory movements. The inferred movements are compared with template patterns prepared from training movements when the relationship was learned to regenerate an acoustic recognition. In a preferred embodiment, the acoustic articulatory relationships are learned by a neural network. Subsequent input acoustic patterns then generate the inferred articulatory movements for use with the templates. Articulatory movement data may be supplemented with characteristic acoustic information, e.g. relative power and high frequency data, to improve template recognition.

Individual-level movement bias leads to the formation of higher-order social structure in a mobile group of baboons.

PubMed

Bonnell, Tyler R; Clarke, Parry M; Henzi, S Peter; Barrett, Louise

2017-07-01

In mobile social groups, influence patterns driving group movement can vary between democratic and despotic. The arrival at any single pattern of influence is thought to be underpinned by both environmental factors and group composition. To identify the specific patterns of influence driving travel decision-making in a chacma baboon troop, we used spatially explicit data to extract patterns of individual movement bias. We scaled these estimates of individual-level bias to the level of the group by constructing an influence network and assessing its emergent structural properties. Our results indicate that there is heterogeneity in movement bias: individual animals respond consistently to particular group members, and higher-ranking animals are more likely to influence the movement of others. This heterogeneity resulted in a group-level network structure that consisted of a single core and two outer shells. Here, the presence of a core suggests that a set of highly interdependent animals drove routine group movements. These results suggest that heterogeneity at the individual level can lead to group-level influence structures, and that movement patterns in mobile social groups can add to the exploration of both how these structures develop (i.e. mechanistic aspects) and what consequences they have for individual- and group-level outcomes (i.e. functional aspects).

Individual-level movement bias leads to the formation of higher-order social structure in a mobile group of baboons

PubMed Central

Clarke, Parry M.; Henzi, S. Peter; Barrett, Louise

2017-01-01

In mobile social groups, influence patterns driving group movement can vary between democratic and despotic. The arrival at any single pattern of influence is thought to be underpinned by both environmental factors and group composition. To identify the specific patterns of influence driving travel decision-making in a chacma baboon troop, we used spatially explicit data to extract patterns of individual movement bias. We scaled these estimates of individual-level bias to the level of the group by constructing an influence network and assessing its emergent structural properties. Our results indicate that there is heterogeneity in movement bias: individual animals respond consistently to particular group members, and higher-ranking animals are more likely to influence the movement of others. This heterogeneity resulted in a group-level network structure that consisted of a single core and two outer shells. Here, the presence of a core suggests that a set of highly interdependent animals drove routine group movements. These results suggest that heterogeneity at the individual level can lead to group-level influence structures, and that movement patterns in mobile social groups can add to the exploration of both how these structures develop (i.e. mechanistic aspects) and what consequences they have for individual- and group-level outcomes (i.e. functional aspects). PMID:28791140

Treatment of temporomandibular myofascial pain with deep dry needling

PubMed Central

Gonzalez-Perez, Luis M.; Granados-Nuñez, Mercedes; Urresti-Lopez, Francisco J.

2012-01-01

Objectives: The present study was designed to evaluate the usefulness of deep dry needling in the treatment of temporomandibular myofascial pain. Study Design: We selected 36 patients with myofascial pain located in the external pterygoid muscle (30 women/6 men, mean age=27 years with SD±6,5). We studied differences in pain with a visual analog scale and range of mandibular movements before and after intervention. Results: We found a statistically significant relationship (p<0,01) between therapeutic intervention and the improvement of pain and jaw movements, which continued up to 6 months after treatment. Pain reduction was greater the higher was the intensity of pain at baseline. Conclusions: Although further studies are needed, our findings suggest that deep dry needling in the trigger point in the external pterygoid muscle can be effective in the management of patients with myofascial pain located in that muscle. Key words:Temporomandibular joint, myofascial pain, external pterygoid muscle, trigger point, deep dry needling. PMID:22549679

A high-resolution line sensor-based photostereometric system for measuring jaw movements in 6 degrees of freedom.

PubMed

Hayashi, T; Kurokawa, M; Miyakawa, M; Aizawa, T; Kanaki, A; Saitoh, A; Ishioka, K

1994-01-01

Photostereometry has widely been applied to the measurement of mandibular movements in 6 degrees of freedom. In order to improve the accuracy of this measurement, we developed a system utilizing small LEDs mounted on the jaws in redundant numbers and a 5000 pixel linear charge-coupled device (CCD) as a photo-sensor. A total of eight LEDs are mounted on the jaws, in two sets of four, by means of connecting facebows, each weighing approximately 55 g. The position of the LEDs are detected in three-dimensions by two sets of three CCD cameras, located bilaterally. The position and orientation of the mandible are estimated from the positions of all LEDs measured in the sense of least-squares, thereby effectively reducing the measurement errors. The static overall accuracy at all tooth and condylar points was considered to lie within 0.19 and 0.34 mm, respectively, from various accuracy verification tests.

Class III malocclusion with complex problems of lateral open bite and severe crowding successfully treated with miniscrew anchorage and lingual orthodontic brackets.

PubMed

Yanagita, Takeshi; Kuroda, Shingo; Takano-Yamamoto, Teruko; Yamashiro, Takashi

2011-05-01

In this article, we report the successful use of miniscrews in a patient with an Angle Class III malocclusion, lateral open bite, midline deviation, and severe crowding. Simultaneously resolving such problems with conventional Class III treatment is difficult. In this case, the treatment procedure was even more challenging because the patient preferred to have lingual brackets on the maxillary teeth. As a result, miniscrews were used to facilitate significant asymmetric tooth movement in the posterior and downward directions; this contributed to the camouflage of the skeletal mandibular protrusion together with complete resolution of the severe crowding and lateral open bite. Analysis of the jaw motion showed that irregularities in chewing movement were also resolved, and a stable occlusion was achieved. Improvements in the facial profile and dental arches remained stable at the 18-month follow-up. Copyright © 2011 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Step selection techniques uncover the environmental predictors of space use patterns in flocks of Amazonian birds.

PubMed

Potts, Jonathan R; Mokross, Karl; Stouffer, Philip C; Lewis, Mark A

2014-12-01

Understanding the behavioral decisions behind animal movement and space use patterns is a key challenge for behavioral ecology. Tools to quantify these patterns from movement and animal-habitat interactions are vital for transforming ecology into a predictive science. This is particularly important in environments undergoing rapid anthropogenic changes, such as the Amazon rainforest, where animals face novel landscapes. Insectivorous bird flocks are key elements of avian biodiversity in the Amazonian ecosystem. Therefore, disentangling and quantifying the drivers behind their movement and space use patterns is of great importance for Amazonian conservation. We use a step selection function (SSF) approach to uncover environmental drivers behind movement choices. This is used to construct a mechanistic model, from which we derive predicted utilization distributions (home ranges) of flocks. We show that movement decisions are significantly influenced by canopy height and topography, but depletion and renewal of resources do not appear to affect movement significantly. We quantify the magnitude of these effects and demonstrate that they are helpful for understanding various heterogeneous aspects of space use. We compare our results to recent analytic derivations of space use, demonstrating that the analytic approximation is only accurate when assuming that there is no persistence in the animals' movement. Our model can be translated into other environments or hypothetical scenarios, such as those given by proposed future anthropogenic actions, to make predictions of spatial patterns in bird flocks. Furthermore, our approach is quite general, so could potentially be used to understand the drivers of movement and spatial patterns for a wide variety of animal communities.

Step selection techniques uncover the environmental predictors of space use patterns in flocks of Amazonian birds

PubMed Central

Potts, Jonathan R; Mokross, Karl; Stouffer, Philip C; Lewis, Mark A

2014-01-01

Understanding the behavioral decisions behind animal movement and space use patterns is a key challenge for behavioral ecology. Tools to quantify these patterns from movement and animal–habitat interactions are vital for transforming ecology into a predictive science. This is particularly important in environments undergoing rapid anthropogenic changes, such as the Amazon rainforest, where animals face novel landscapes. Insectivorous bird flocks are key elements of avian biodiversity in the Amazonian ecosystem. Therefore, disentangling and quantifying the drivers behind their movement and space use patterns is of great importance for Amazonian conservation. We use a step selection function (SSF) approach to uncover environmental drivers behind movement choices. This is used to construct a mechanistic model, from which we derive predicted utilization distributions (home ranges) of flocks. We show that movement decisions are significantly influenced by canopy height and topography, but depletion and renewal of resources do not appear to affect movement significantly. We quantify the magnitude of these effects and demonstrate that they are helpful for understanding various heterogeneous aspects of space use. We compare our results to recent analytic derivations of space use, demonstrating that the analytic approximation is only accurate when assuming that there is no persistence in the animals' movement. Our model can be translated into other environments or hypothetical scenarios, such as those given by proposed future anthropogenic actions, to make predictions of spatial patterns in bird flocks. Furthermore, our approach is quite general, so could potentially be used to understand the drivers of movement and spatial patterns for a wide variety of animal communities. PMID:25558353

Neuroleptic-induced movement disorders in a naturalistic schizophrenia population: diagnostic value of actometric movement patterns.

PubMed

Janno, Sven; Holi, Matti M; Tuisku, Katinka; Wahlbeck, Kristian

2008-04-18

Neuroleptic-induced movement disorders (NIMDs) have overlapping co-morbidity. Earlier studies have described typical clinical movement patterns for individual NIMDs. This study aimed to identify specific movement patterns for each individual NIMD using actometry. A naturalistic population of 99 schizophrenia inpatients using conventional antipsychotics and clozapine was evaluated. Subjects with NIMDs were categorized using the criteria for NIMD found in the Diagnostic and Statistical Manual for Mental Disorders - Fourth Edition (DSM-IV).Two blinded raters evaluated the actometric-controlled rest activity data for activity periods, rhythmical activity, frequencies, and highest acceleration peaks. A simple subjective question was formulated to test patient-based evaluation of NIMD. The patterns of neuroleptic-induced akathisia (NIA) and pseudoakathisia (PsA) were identifiable in actometry with excellent inter-rater reliability. The answers to the subjective question about troubles with movements distinguished NIA patients from other patients rather well. Also actometry had rather good screening performances in distinguishing akathisia from other NIMD. Actometry was not able to reliably detect patterns of neuroleptic-induced parkinsonism and tardive dyskinesia. The present study showed that pooled NIA and PsA patients had a different pattern in lower limb descriptive actometry than other patients in a non-selected sample. Careful questioning of patients is a useful method of diagnosing NIA in a clinical setting.

Movement characteristics of persons with prader-willi syndrome rising from supine.

PubMed

Belt, A B; Hertel, T A; Mante, J R; Marks, T; Rockett, V L; Wade, C; Clayton-Krasinski, D

2001-01-01

The purposes of this study were to: 1) determine if previously published descriptors of the supine to stand rising task in healthy individuals could be applied to the movements of persons with Prader-Willi Syndrome (PWS); and 2) assess upper extremity (UE), axial region (AX), and lower extremity (LE) movements among subjects with PWS compared with controls. Nine subjects with PWS (seven-36 years of age) and matched controls were videotaped performing 10 rising trials. The UE, AX, and LE movements were classified using published descriptors. Occurrence frequencies of movement patterns, duration of movement, and the relationships among body region movement score, BMI, and age were determined. Subjects with PWS utilized developmentally less advanced asymmetrical rising patterns, took longer to rise, and demonstrated less within subject variability than controls. Categorical descriptors, with minor modifications, can be used to describe rising movements in persons with PWS. Knowledge of successful rising patterns may assist PTs when examining or planning intervention strategies for teaching the rising task.

Factors associated with mandibular third molar eruption and impaction.

PubMed

Tsai, Hung-Huey

2005-01-01

A retrospective study, using panoramic radiographs, was conducted on 152 Taiwanese (72 males and 80 females) to investigate mandibular third molar eruption and impaction. The following measurements were made: inclinations and mesiodistal crown widths of the mandibular molars, vertical and horizontal spaces between the distal surface of the second molar and the anterior surface of the ramus, lengths and widths of the mandibular ramus and body, the ramus inclination, the mandibular plane angle, and the mandibular gonial angle. Differences between non-impaction and impaction groups were studied, and the variables were analyzed with multivariate discriminatory analysis. Significant differences between the two groups were found; variables describing spaces between the anterior of the ramus and the distal of the mandibular second molar and tooth size appeared to be the primary contributors to the differences observed.

Endodontic management of contralateral mandibular first molars with six root canals

PubMed Central

Bhargav, Kambhampati; Sirisha, Kantheti; Jyothi, Mandava; Boddeda, Mohan Rao

2017-01-01

The knowledge of variations in root canal morphology is essential for a successful endodontic outcome. Contralateral mandibular molar with six root canals is a rare entity. Root canal treatment of mandibular molars with aberrant canal configuration can be diagnostically and technically challenging. While dealing with variant mandibular molars, mishaps may happen. This case report describes variations in contralateral mandibular molars and also an endodontic mishap while managing them. PMID:29259369

A Correlational Study of Scoliosis and Trunk Balance in Adult Patients with Mandibular Deviation

PubMed Central

Yang, Yang; Wang, Na; Wang, Wenyong; Ding, Yin; Sun, Shiyao

2013-01-01

Previous studies have confirmed that patients with mandibular deviation often have abnormal morphology of their cervical vertebrae. However, the relationship between mandibular deviation, scoliosis, and trunk balance has not been studied. Currently, mandibular deviation is usually treated as a single pathology, which leads to poor clinical efficiency. We investigated the relationship of spine coronal morphology and trunk balance in adult patients with mandibular deviation, and compared the finding to those in healthy volunteers. 35 adult patients with skeletal mandibular deviation and 10 healthy volunteers underwent anterior X-ray films of the head and posteroanterior X-ray films of the spine. Landmarks and lines were drawn and measured on these films. The axis distance method was used to measure the degree of scoliosis and the balance angle method was used to measure trunk balance. The relationship of mandibular deviation, spine coronal morphology and trunk balance was evaluated with the Pearson correlation method. The spine coronal morphology of patients with mandibular deviation demonstrated an “S” type curve, while a straight line parallel with the gravity line was found in the control group (significant difference, p<0.01). The trunk balance of patients with mandibular deviation was disturbed (imbalance angle >1°), while the control group had a normal trunk balance (imbalance angle <1°). There was a significant difference between the two groups (p<0.01). The degree of scoliosis and shoulder imbalance correlated with the degree of mandibular deviation, and presented a linear trend. The direction of mandibular deviation was the same as that of the lateral bending of thoracolumbar vertebrae, which was opposite to the direction of lateral bending of cervical vertebrae. Our study shows the degree of mandibular deviation has a high correlation with the degree of scoliosis and trunk imbalance, all the three deformities should be clinically evaluated in the management of mandibular deviation. PMID:23555836

Ectopic application of recombinant BMP-2 and BMP-4 can change patterning of developing chick facial primordia.

PubMed

Barlow, A J; Francis-West, P H

1997-01-01

The facial primordia initially consist of buds of undifferentiated mesenchyme, which give rise to a variety of tissues including cartilage, muscle and nerve. These must be arranged in a precise spatial order for correct function. The signals that control facial outgrowth and patterning are largely unknown. The bone morphogenetic proteins Bmp-2 and Bmp-4 are expressed in discrete regions at the distal tips of the early facial primordia suggesting possible roles for BMP-2 and BMP-4 during chick facial development. We show that expression of Bmp-4 and Bmp-2 is correlated with the expression of Msx-1 and Msx-2 and that ectopic application of BMP-2 and BMP-4 can activate Msx-1 and Msx-2 gene expression in the developing facial primordia. We correlate this activation of gene expression with changes in skeletal development. For example, activation of Msx-1 gene expression across the distal tip of the mandibular primordium is associated with an extension of Fgf-4 expression in the epithelium and bifurcation of Meckel's cartilage. In the maxillary primordium, extension of the normal domain of Msx-1 gene expression is correlated with extended epithelial expression of shh and bifurcation of the palatine bone. We also show that application of BMP-2 can increase cell proliferation of the mandibular primordia. Our data suggest that BMP-2 and BMP-4 are part of a signalling cascade that controls outgrowth and patterning of the facial primordia.

Cattle movement patterns in Australia: an analysis of the NLIS database 2008-2012.

PubMed

Iglesias, R M; East, I J

2015-11-01

To identify patterns of cattle movement that could influence disease spread in the Australian cattle population. Records from the National Livestock Identification System database for the period January 2008 to December 2012 were accessed and analysed. Postcodes were used to allocate each individual property to one of 12 livestock production regions. National movement patterns and the characteristics of each livestock production region were quantified in terms of the number of consignments and animals moved, and seasonality of movements. The majority of cattle movements remained within a single livestock production region, while those that did not, usually remained within the same state or territory. Producers were the most common source of cattle, and abattoirs and other producers the most common destinations, with approximately 40% of animals moving via a saleyard. The northern regions generally moved larger consignments than the southern regions and were less connected to other regions. The eastern and south-eastern regions were very well connected by cattle movements. Seasonal patterns were seen for some regions, particularly the northern regions where weather patterns strongly influence the ability of producers to muster and transport stock. The movement patterns observed provide quantitative support for previous information based on surveys and expert opinion, and capture more of the variability in Australian cattle production. This information may assist with management of animal disease risks, in particular exotic diseases, and in planning surveillance programs. © 2015 2015 Commonwealth of Australia Australian Veterinary Journal © 2015 Australian Veterinary Association.

Mutual information in the evolution of trajectories in discrete aiming movements.

PubMed

Lai, Shih-Chiung; Mayer-Kress, Gottfried; Newell, Karl M

2008-07-01

This study investigated the mutual information in the trajectories of discrete aiming movements on a computer controlled graphics tablet where movement time ( 300 - 2050 ms) was manipulated in a given distance (100 mm) and movement distance (15-240 mm) in 2 given movement times (300 ms and 800 ms ). For the distance-fixed conditions, there was higher mutual information in the slower movements in the 0 vs. 80-100% trajectory point comparisons, whereas the mutual information was higher for the faster movements when comparing within the 80 and 100% points of the movement trajectory. For the time-fixed conditions, the spatial constraints led to a decreasing pattern of the mutual information throughout the points of the trajectory, with the highest mutual information found in the 80 vs. 100% comparison. Overall, the pattern of mutual information reveals systematic modulation of the trajectories between the attractive fixed point of the target as a function of movement condition. These mutual information patterns are postulated to be the consequence of the different relative contributions of feedforward and feedback control processes in trajectory formation as a function of task constraints.

Superolateral dislocation of an intact mandibular condyle into the temporal fossa: case report and literature review.

PubMed

Sharma, Divashree; Khasgiwala, Ankit; Maheshwari, Bharat; Singh, Charanpreet; Shakya, Neelam

2017-02-01

Temporomandibular joint dislocation refers to the dislodgement of mandibular condyle from the glenoid fossa. Anterior and anteromedial dislocations of the mandibular condyle are frequently reported in the literature, but superolateral dislocation is a rare presentation. This report outlines a case of superolateral dislocation of an intact mandibular condyle that occurred in conjunction with an ipsilateral mandibular parasymphysis fracture. A review of the clinical features of superolateral dislocation of the mandibular condyle and the possible techniques of its reduction ranging from the most conservative means to extensive surgical interventions is presented. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Management of mandibular body fractures in pediatric patients: a case report with review of literature.

PubMed

John, Baby; John, Reena R; Stalin, A; Elango, Indumathi

2010-10-01

Mandibular fractures are relatively less frequent in children when compared to adults, which may be due to the child's protected anatomic features and infrequent exposure of children to alcohol related traffic accidents. Treatment principles of mandibular fractures differ from that of adults due to concerns regarding mandibular growth and development of dentition. A case of a 4.5-year-old boy with fractured body of mandible managed by closed reduction using open occlusal acrylic splint and circum mandibular wiring is presented. This article also provides a review of literature regarding the management of mandibular body fracture in young children.

Management of mandibular body fractures in pediatric patients: A case report with review of literature

PubMed Central

John, Baby; John, Reena R.; Stalin, A.; Elango, Indumathi

2010-01-01

Mandibular fractures are relatively less frequent in children when compared to adults, which may be due to the child's protected anatomic features and infrequent exposure of children to alcohol related traffic accidents. Treatment principles of mandibular fractures differ from that of adults due to concerns regarding mandibular growth and development of dentition. A case of a 4.5-year-old boy with fractured body of mandible managed by closed reduction using open occlusal acrylic splint and circum mandibular wiring is presented. This article also provides a review of literature regarding the management of mandibular body fracture in young children. PMID:22114443

Heritability of mandibular cephalometric variables in twins with completed craniofacial growth.

PubMed

Šidlauskas, Mantas; Šalomskienė, Loreta; Andriuškevičiūtė, Irena; Šidlauskienė, Monika; Labanauskas, Žygimantas; Vasiliauskas, Arūnas; Kupčinskas, Limas; Juzėnas, Simonas; Šidlauskas, Antanas

2016-10-01

To determine genetic and environmental impact on mandibular morphology using lateral cephalometric analysis of twins with completed mandibular growth and deoxyribonucleic acid (DNA) based zygosity determination. The 39 cephalometric variables of 141 same gender adult pair of twins were analysed. Zygosity was determined using 15 specific DNA markers and cervical vertebral maturation method was used to assess completion of the mandibular growth. A genetic analysis was performed using maximum likelihood genetic structural equation modelling (GSEM). The genetic heritability estimates of angular variables describing horizontal mandibular position in relationship to cranial base and maxilla were considerably higher than in those describing vertical position. The mandibular skeletal cephalometric variables also showed high heritability estimates with angular measurements being considerably higher than linear ones. Results of this study indicate that the angular measurements representing mandibular skeletal morphology (mandibular form) have greater genetic determination than the linear measurements (mandibular size). The shape and sagittal position of the mandible is under stronger genetic control, than is its size and vertical relationship to cranial base. © The Author 2015. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Reliability of mandibular canines as indicators for sexual dichotomy.

PubMed

Hosmani, Jagadish V; Nayak, Ramakant S; Kotrashetti, Vijayalakshmi S; S, Pradeep; Babji, Deepa

2013-02-01

Amongst the various calcified structures in the human body, teeth have gained lot of popularity in estimating the sex of an individual as they are highly resistant to destruction and decomposition. Using permanent mandibular canines many researchers have predicted a high level of accuracy in identifying the sex correctly. The purpose of our study was to gauge the effectiveness of mandibular canines in discerning sex. Fifty dental casts each of males and females were utilized for the study. Mesio-distal dimension and inter-canine distance of mandibular right and left canine was recorded using digital vernier caliper and mandibular canine index was calculated. The mean value of mesio-distal dimensions of right and left mandibular canine was slightly greater in males compared to females. The mandibular canine index was equal in both sexes. Inter-canine distance was marginally higher in males compared to females. Despite of higher values in males none of the parameters were statistically significant. The results herein bolster contemporary studies that mesio-distal dimensions of mandibular canines and mandibular canine index do not reflect sexual dimorphism and that its application should be discontinued in sex prediction among Indian populations. How to cite this article: Hosmani J V, Nayak R S, Kotrashetti V S, Pradeep S, Babji D. Reliability of Mandibular Canines as Indicators for Sexual Dichotomy. J Int Oral Health 2013; 5(1):1-7.

The “at-home LLLT” in temporo-mandibular disorders pain control: a pilot study

PubMed Central

Pelosi, A; Queirolo, V; Vescovi, P; Merigo, E

2015-01-01

Objectives: The Temporo-Mandibular Disorders (TMD) are a set of dysfunctional patterns concerning the temporo-mandibular joints (TMJ) and the masticatory muscles; its main symptom is pain, probably caused by inflammatory changes in the synovial membrane, alterations in the bone marrow of the mandibular condyle and impingement and compression. The aim of this preliminary study was to investigate the effectiveness in the TMD pain reduction of a new laser device recently proposed by the commerce that, due to its reduced dimensions and to be a class I laser according the ANSI classification, may be used at home by the patient himself. Material and methods: Twenty-four patients with TMD were randomly selected: the inclusion criteria for the sample was the diagnosis of mono- or bi-lateral TMD, with acute pain restricted to the joint area, associated with the absence of any muscle tenderness during palpation. The patients were randomly assigned to two groups: Group 1 (12 patients): patients receiving real LLLT (experimental group). Group 2 (12 patients): patients receiving inactive laser (placebo group). The treatment was performed once a day for two weeks with an 808 nm diode laser by the patient himself with irradiation of the cutaneous zone corresponding to the TMJ for 15 minutes each side. Each patient was instructed to express its pain in a visual analogue scale (VAS) making a perpendicular line between the two extremes representing the felt pain level. Statistical analysis was realized with GraphPad Instat Software, where P<0.05 was considered significant and P<0.01 very significant. Results: The patient's pain evaluation was expressed in the two study groups before the treatment, 1 week and two weeks after the treatment. The differences between the two groups result extremely significant with p<0.0001 for the comparison of VAS value after 1 and 2 weeks. Conclusion: This study, even if it may be considered such a pilot study, investigated a new way to control the pain in the temporo-mandibular diseases by an at home self administered laser device. Results are encouraging but they will have to be confirmed by greater studies. PMID:25941425

The "at-home LLLT" in temporo-mandibular disorders pain control: a pilot study.

PubMed

Fornaini, C; Pelosi, A; Queirolo, V; Vescovi, P; Merigo, E

2015-03-31

The Temporo-Mandibular Disorders (TMD) are a set of dysfunctional patterns concerning the temporo-mandibular joints (TMJ) and the masticatory muscles; its main symptom is pain, probably caused by inflammatory changes in the synovial membrane, alterations in the bone marrow of the mandibular condyle and impingement and compression. The aim of this preliminary study was to investigate the effectiveness in the TMD pain reduction of a new laser device recently proposed by the commerce that, due to its reduced dimensions and to be a class I laser according the ANSI classification, may be used at home by the patient himself. Twenty-four patients with TMD were randomly selected: the inclusion criteria for the sample was the diagnosis of mono- or bi-lateral TMD, with acute pain restricted to the joint area, associated with the absence of any muscle tenderness during palpation. The patients were randomly assigned to two groups: Group 1 (12 patients): patients receiving real LLLT (experimental group). Group 2 (12 patients): patients receiving inactive laser (placebo group). The treatment was performed once a day for two weeks with an 808 nm diode laser by the patient himself with irradiation of the cutaneous zone corresponding to the TMJ for 15 minutes each side. Each patient was instructed to express its pain in a visual analogue scale (VAS) making a perpendicular line between the two extremes representing the felt pain level. Statistical analysis was realized with GraphPad Instat Software, where P<0.05 was considered significant and P<0.01 very significant. The patient's pain evaluation was expressed in the two study groups before the treatment, 1 week and two weeks after the treatment. The differences between the two groups result extremely significant with p<0.0001 for the comparison of VAS value after 1 and 2 weeks. This study, even if it may be considered such a pilot study, investigated a new way to control the pain in the temporo-mandibular diseases by an at home self administered laser device. RESULTS are encouraging but they will have to be confirmed by greater studies.

How landscape dynamics link individual- to population-level movement patterns: A multispecies comparison of ungulate relocation data

USGS Publications Warehouse

Mueller, Thomas; Olson, K.A.; Dressler, G.; Leimgruber, Peter; Fuller, Todd K.; Nicholson, Craig; Novaro, A.J.; Bolgeri, M.J.; Wattles, David W.; DeStefano, Stephen; Calabrese, J.M.; Fagan, William F.

2011-01-01

Aim  To demonstrate how the interrelations of individual movements form large-scale population-level movement patterns and how these patterns are associated with the underlying landscape dynamics by comparing ungulate movements across species.Locations  Arctic tundra in Alaska and Canada, temperate forests in Massachusetts, Patagonian Steppes in Argentina, Eastern Steppes in Mongolia.Methods  We used relocation data from four ungulate species (barren-ground caribou, Mongolian gazelle, guanaco and moose) to examine individual movements and the interrelation of movements among individuals. We applied and developed a suite of spatial metrics that measure variation in movement among individuals as population dispersion, movement coordination and realized mobility. Taken together, these metrics allowed us to quantify and distinguish among different large-scale population-level movement patterns such as migration, range residency and nomadism. We then related the population-level movement patterns to the underlying landscape vegetation dynamics via long-term remote sensing measurements of the temporal variability, spatial variability and unpredictability of vegetation productivity.Results  Moose, which remained in sedentary home ranges, and guanacos, which were partially migratory, exhibited relatively short annual movements associated with landscapes having very little broad-scale variability in vegetation. Caribou and gazelle performed extreme long-distance movements that were associated with broad-scale variability in vegetation productivity during the peak of the growing season. Caribou exhibited regular seasonal migration in which individuals were clustered for most of the year and exhibited coordinated movements. In contrast, gazelle were nomadic, as individuals were independently distributed and moved in an uncoordinated manner that relates to the comparatively unpredictable (yet broad-scale) vegetation dynamics of their landscape.Main conclusions  We show how broad-scale landscape unpredictability may lead to nomadism, an understudied type of long-distance movement. In contrast to classical migration where landscapes may vary at broad scales but in a predictable manner, long-distance movements of nomadic individuals are uncoordinated and independent from other such individuals. Landscapes with little broad-scale variability in vegetation productivity feature smaller-scale movements and allow for range residency. Nomadism requires distinct integrative conservation strategies that facilitate long-distance movements across the entire landscape and are not limited to certain migration corridors.

How landscape dynamics link individual- to population-level movement patterns: A multispecies comparison of ungulate relocation data

USGS Publications Warehouse

Mueller, T.; Olson, K.A.; Dressler, G.; Leimgruber, P.; Fuller, T.K.; Nicolson, C.; Novaro, A.J.; Bolgeri, M.J.; Wattles, David W.; DeStefano, S.; Calabrese, J.M.; Fagan, W.F.

2011-01-01

Aim To demonstrate how the interrelations of individual movements form large-scale population-level movement patterns and how these patterns are associated with the underlying landscape dynamics by comparing ungulate movements across species. Locations Arctic tundra in Alaska and Canada, temperate forests in Massachusetts, Patagonian Steppes in Argentina, Eastern Steppes in Mongolia. Methods We used relocation data from four ungulate species (barren-ground caribou, Mongolian gazelle, guanaco and moose) to examine individual movements and the interrelation of movements among individuals. We applied and developed a suite of spatial metrics that measure variation in movement among individuals as population dispersion, movement coordination and realized mobility. Taken together, these metrics allowed us to quantify and distinguish among different large-scale population-level movement patterns such as migration, range residency and nomadism. We then related the population-level movement patterns to the underlying landscape vegetation dynamics via long-term remote sensing measurements of the temporal variability, spatial variability and unpredictability of vegetation productivity. Results Moose, which remained in sedentary home ranges, and guanacos, which were partially migratory, exhibited relatively short annual movements associated with landscapes having very little broad-scale variability in vegetation. Caribou and gazelle performed extreme long-distance movements that were associated with broad-scale variability in vegetation productivity during the peak of the growing season. Caribou exhibited regular seasonal migration in which individuals were clustered for most of the year and exhibited coordinated movements. In contrast, gazelle were nomadic, as individuals were independently distributed and moved in an uncoordinated manner that relates to the comparatively unpredictable (yet broad-scale) vegetation dynamics of their landscape. Main conclusions We show how broad-scale landscape unpredictability may lead to nomadism, an understudied type of long-distance movement. In contrast to classical migration where landscapes may vary at broad scales but in a predictable manner, long-distance movements of nomadic individuals are uncoordinated and independent from other such individuals. Landscapes with little broad-scale variability in vegetation productivity feature smaller-scale movements and allow for range residency. Nomadism requires distinct integrative conservation strategies that facilitate long-distance movements across the entire landscape and are not limited to certain migration corridors. ?? 2011 Blackwell Publishing Ltd.

Long-Term Results of Mandibular Distraction Osteogenesis with a Resorbable Device in Infants with Robin Sequence: Effects on Developing Molars and Mandibular Growth.

PubMed

Paes, Emma C; Bittermann, Gerhard K P; Bittermann, Dirk; Muradin, Marvick M; van Hogezand, Rose; Etty, Erika; Mink van der Molen, Aebele B; Kon, Moshe; Breugem, Corstiaan C

2016-02-01

Mandibular distraction osteogenesis with a unidirectional resorbable device is an effective treatment option for severe upper airway obstruction in infants with Robin sequence. Long-term effects, especially with regard to tooth development and mandibular outgrowth, are not known. Robin sequence infants with a follow-up of greater than or equal to 5 years were included. Baseline characteristics were extracted from medical records. Panoramic and lateral cephalometric radiographs were analyzed and patients were recalled for physical examination. Ten infants underwent mandibular distraction osteogenesis at a mean age of 3.7 months (median, 19 months; range, 11 days to 27 months). Mean length of follow-up was 6.8 years (range, 5.0 to 7.9 years). Ten Robin sequence infants without mandibular distraction osteogenesis (mean length of follow-up, 7.4 years; range, 6.7 to 8.9 years) were the controls. Shape anomalies, positional changes, and root malformations of molars were seen significantly more often than in the control group (p = 0.007, p = 0.009, and p = 0.043, respectively). Mandibular length was shorter (p = 0.030), but mandibular ramus height was comparable (p = 0.838) with that of the non-mandibular distraction osteogenesis group. Compared with healthy controls, all Robin sequence infants had a significantly shorter mandible. Mandibular distraction osteogenesis with a resorbable system reveals overall good short- and long-term results, but the effects on developing molars and mandibular outgrowth likely necessitate secondary procedures. This factor should be considered when deciding on treatment options and counseling of parents. Therapeutic, III.

How superdiffusion gets arrested: ecological encounters explain shift from Lévy to Brownian movement

PubMed Central

de Jager, Monique; Bartumeus, Frederic; Kölzsch, Andrea; Weissing, Franz J.; Hengeveld, Geerten M.; Nolet, Bart A.; Herman, Peter M. J.; van de Koppel, Johan

2014-01-01

Ecological theory uses Brownian motion as a default template for describing ecological movement, despite limited mechanistic underpinning. The generality of Brownian motion has recently been challenged by empirical studies that highlight alternative movement patterns of animals, especially when foraging in resource-poor environments. Yet, empirical studies reveal animals moving in a Brownian fashion when resources are abundant. We demonstrate that Einstein's original theory of collision-induced Brownian motion in physics provides a parsimonious, mechanistic explanation for these observations. Here, Brownian motion results from frequent encounters between organisms in dense environments. In density-controlled experiments, movement patterns of mussels shifted from Lévy towards Brownian motion with increasing density. When the analysis was restricted to moves not truncated by encounters, this shift did not occur. Using a theoretical argument, we explain that any movement pattern approximates Brownian motion at high-resource densities, provided that movement is interrupted upon encounters. Hence, the observed shift to Brownian motion does not indicate a density-dependent change in movement strategy but rather results from frequent collisions. Our results emphasize the need for a more mechanistic use of Brownian motion in ecology, highlighting that especially in rich environments, Brownian motion emerges from ecological interactions, rather than being a default movement pattern. PMID:24225464

How superdiffusion gets arrested: ecological encounters explain shift from Lévy to Brownian movement.

PubMed

de Jager, Monique; Bartumeus, Frederic; Kölzsch, Andrea; Weissing, Franz J; Hengeveld, Geerten M; Nolet, Bart A; Herman, Peter M J; van de Koppel, Johan

2014-01-07

Ecological theory uses Brownian motion as a default template for describing ecological movement, despite limited mechanistic underpinning. The generality of Brownian motion has recently been challenged by empirical studies that highlight alternative movement patterns of animals, especially when foraging in resource-poor environments. Yet, empirical studies reveal animals moving in a Brownian fashion when resources are abundant. We demonstrate that Einstein's original theory of collision-induced Brownian motion in physics provides a parsimonious, mechanistic explanation for these observations. Here, Brownian motion results from frequent encounters between organisms in dense environments. In density-controlled experiments, movement patterns of mussels shifted from Lévy towards Brownian motion with increasing density. When the analysis was restricted to moves not truncated by encounters, this shift did not occur. Using a theoretical argument, we explain that any movement pattern approximates Brownian motion at high-resource densities, provided that movement is interrupted upon encounters. Hence, the observed shift to Brownian motion does not indicate a density-dependent change in movement strategy but rather results from frequent collisions. Our results emphasize the need for a more mechanistic use of Brownian motion in ecology, highlighting that especially in rich environments, Brownian motion emerges from ecological interactions, rather than being a default movement pattern.

Idiosyncratic characteristics of saccadic eye movements when viewing different visual environments.

PubMed

Andrews, T J; Coppola, D M

1999-08-01

Eye position was recorded in different viewing conditions to assess whether the temporal and spatial characteristics of saccadic eye movements in different individuals are idiosyncratic. Our aim was to determine the degree to which oculomotor control is based on endogenous factors. A total of 15 naive subjects viewed five visual environments: (1) The absence of visual stimulation (i.e. a dark room); (2) a repetitive visual environment (i.e. simple textured patterns); (3) a complex natural scene; (4) a visual search task; and (5) reading text. Although differences in visual environment had significant effects on eye movements, idiosyncrasies were also apparent. For example, the mean fixation duration and size of an individual's saccadic eye movements when passively viewing a complex natural scene covaried significantly with those same parameters in the absence of visual stimulation and in a repetitive visual environment. In contrast, an individual's spatio-temporal characteristics of eye movements during active tasks such as reading text or visual search covaried together, but did not correlate with the pattern of eye movements detected when viewing a natural scene, simple patterns or in the dark. These idiosyncratic patterns of eye movements in normal viewing reveal an endogenous influence on oculomotor control. The independent covariance of eye movements during different visual tasks shows that saccadic eye movements during active tasks like reading or visual search differ from those engaged during the passive inspection of visual scenes.

21 CFR 872.3960 - Mandibular condyle prosthesis.

Code of Federal Regulations, 2010 CFR

2010-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3960 Mandibular condyle prosthesis. (a) Identification. A mandibular condyle prosthesis is a device that is intended to be implanted in the human jaw to... requirement for premarket approval for any mandibular condyle prosthesis intended to be implanted in the human...

Activity characteristics and movement patterns in people with and people without low back pain who participate in rotation-related sports

PubMed Central

Chimenti, Ruth L.; Scholtes, Sara A.

2013-01-01

Many risk factors have been identified as contributing to the development or persistence of low back pain (LBP). However, the juxtaposition of both high and low levels of physical activity being associated with LBP reflects the complexity of the relationship between a risk factor and LBP. Moreover, not everyone with an identified risk factor, such as a movement pattern of increased lumbopelvic rotation, has LBP. Objective The purpose of this study was to examine differences in activity level and movement patterns between people with and people without chronic or recurrent LBP who participate in rotation-related sports. Design Case Case-control study. Setting University laboratory environment. Participants 52 people with chronic or recurrent LBP and 25 people without LBP who all play a rotation-related sport. Main Outcome Measures Participants completed self-report measures including the Baecke Habitual Activity Questionnaire and a questionnaire on rotation-related sports. A 3-dimensional motion-capture system was used to collect movement-pattern variables during 2 lower-limb-movement tests. Results Compared with people without LBP, people with LBP reported a greater difference between the sport subscore and an average work and leisure composite subscore on the Baecke Habitual Activity Questionnaire (F = 6.55, P = .01). There were no differences between groups in either rotation-related-sport participation or movement-pattern variables demonstrated during 2 lower-limb movement tests (P > .05 for all comparisons). Conclusions People with and people without LBP who regularly play a rotation-related sport differed in the amount and nature of activity participation but not in movement pattern variables. An imbalance between level of activity during sport and daily functions may contribute to the development or persistence of LBP in people who play a rotation-related sport. PMID:23295458

Pre-Participation Screening: The Use of Fundamental Movements as an Assessment of Function – Part 1

PubMed Central

Burton, Lee; Hoogenboom, Barb

2006-01-01

To prepare an athlete for the wide variety of activities needed to participate in their sport, the analysis of fundamental movements should be incorporated into pre-participation screening in order to determine who possesses, or lacks, the ability to perform certain essential movements. In a series of two articles, the background and rationale for the analysis of fundamental movement will be provided. In addition, one such evaluation tool that attempts to assess the fundamental movement patterns performed by an individual, the Functional Movement Screen (FMS™), will be described. Three of the seven fundamental movement patterns that comprise the FMS™ are described in detail in Part I: deep squat, hurdle step, and in-line lunge. Part II of this series, which will be published in the August issue of NAJSPT, will provide a brief review of the analysis of fundamental movements, as well a detailed description of the four additional patterns that complement those presented in Part I (to complete the total of seven fundamental movement patterns which comprise the FMS™): shoulder mobility, active straight leg raise, trunk stability push-up, and rotary stability. The intent of this two part series is to introduce the concept of the evaluation of fundamental movements, whether it is the FMS™ system or a different system devised by another clinician. Such a functional assessment should be incorporated into pre-participation screening in order to determine whether the athlete has the essential movements needed to participate in sports activities with a decreased risk of injury. PMID:21522216

Neuroleptic-induced movement disorders in a naturalistic schizophrenia population: diagnostic value of actometric movement patterns

PubMed Central

Janno, Sven; Holi, Matti M; Tuisku, Katinka; Wahlbeck, Kristian

2008-01-01

Background Neuroleptic-induced movement disorders (NIMDs) have overlapping co-morbidity. Earlier studies have described typical clinical movement patterns for individual NIMDs. This study aimed to identify specific movement patterns for each individual NIMD using actometry. Methods A naturalistic population of 99 schizophrenia inpatients using conventional antipsychotics and clozapine was evaluated. Subjects with NIMDs were categorized using the criteria for NIMD found in the Diagnostic and Statistical Manual for Mental Disorders – Fourth Edition (DSM-IV). Two blinded raters evaluated the actometric-controlled rest activity data for activity periods, rhythmical activity, frequencies, and highest acceleration peaks. A simple subjective question was formulated to test patient-based evaluation of NIMD. Results The patterns of neuroleptic-induced akathisia (NIA) and pseudoakathisia (PsA) were identifiable in actometry with excellent inter-rater reliability. The answers to the subjective question about troubles with movements distinguished NIA patients from other patients rather well. Also actometry had rather good screening performances in distinguishing akathisia from other NIMD. Actometry was not able to reliably detect patterns of neuroleptic-induced parkinsonism and tardive dyskinesia. Conclusion The present study showed that pooled NIA and PsA patients had a different pattern in lower limb descriptive actometry than other patients in a non-selected sample. Careful questioning of patients is a useful method of diagnosing NIA in a clinical setting. PMID:18419829

Efficacy of the Nance appliance as an anchorage-reinforcement method.

PubMed

Al-Awadhi, Ebrahim A; Garvey, Therese M; Alhag, Mohamed; Claffey, Noel M; O'Connell, Brian

2015-03-01

The Nance appliance is widely considered to be an efficient method of anchorage reinforcement; however, much of the perceived advantage is based on clinical judgment. The aim of this study was to assess the amounts of anchorage loss and desired tooth movement associated with the Nance appliance. The mandibular arches of 7 beagle dogs were used. The first and third premolars were extracted. Reference miniscrews were placed at the first premolar sites as stable references to measure the amounts of anchorage loss and desired tooth movement. Four beagles were fitted with custom-made Nance appliances on the fourth premolars and orthodontic bands on the second premolars (Nance group). Three beagles were fitted with orthodontic bands on the second and fourth premolars with no anchorage reinforcement (control group). The second premolars were retracted over 15 weeks in both groups. The amounts of second premolar movement (desired tooth movement) and fourth premolar movement (anchorage loss) were recorded at 5, 10, and 15 weeks. The percentages of desired tooth movement and anchorage loss to the total space closure were calculated. The mean desired tooth movement was significantly more in the Nance group than in the control group at 10 weeks (P <0.05) but was not significantly different at 5 and 15 weeks. The mean percentages of anchorage loss to the total space closure at 15 weeks were 45.7% in the control group and 28.8% in the Nance group. The Nance group had 16.9% less anchorage loss and 16.6% more desired tooth movement than did the control group at 15 weeks (P <0.05). Most of the anchorage loss (80%) in the Nance group occurred during the first 10 weeks. The Nance appliance did not provide absolute anchorage, but there was significantly less anchorage loss with it than in the control group. The majority of anchorage loss occurred during the first 10 weeks in the Nance group. Copyright © 2015 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Successful Treatment of Postpeak Stage Patients with Class II Division 1 Malocclusion Using Non-extraction and Multiloop Edgewise Archwire Therapy: A Report on 16 Cases

PubMed Central

Liu, Jun; Zou, Ling; Zhao, Zhi-he; Welburn, Neala; Yang, Pu; Tang, Tian; Li, Yu

2009-01-01

Aim To determine cephalometrically the mechanism of the treatment effects of non-extraction and multiloop edgewise archwire (MEAW) technique on postpeak Class II Division 1 patients. Methodology In this retrospective study, 16 postpeak Class II Division 1 patients successfully corrected using a non-extraction and MEAW technique were cephalometrically evaluated and compared with 16 matched control subjects treated using an extraction technique. Using CorelDRAW® software, standardized digital cephalograms pre- and post-active treatments were traced and a reference grid was set up. The superimpositions were based on the cranial base, the mandibular and the maxilla regions,and skeletal and dental changes were measured. Changes following treatment were evaluated using the paired-sample t-test. Student's t-test for unpaired samples was used to assess the differences in changes between the MEAW and the extraction control groups. Results The correction of the molar relationships comprised 54% skeletal change (mainly the advancement of the mandible) and 46% dental change. Correction of the anterior teeth relationships comprised 30% skeletal change and 70% dental change. Conclusion The MEAW technique can produce the desired vertical and sagittal movement of the tooth segment and then effectively stimulate mandibular advancement by utilizing the residual growth potential of the condyle. PMID:20690424

Radiation-induced temporo-mandibular joint disorder in post-radiotherapy nasopharyngeal carcinoma patients: assessment and treatment.

PubMed

Wu, Vincent W C; Lam, Ying-Na

2016-06-01

Nasopharyngeal carcinoma (NPC) is endemic in southern China, and its incidence in Hong Kong is relatively high. Radiotherapy is the mainstay treatment for NPC due to its relatively high radiosensitivity and deep-seated anatomical position, which is not readily accessible by surgery. Although the technique of radiotherapy in NPC has been advancing and offers promising treatment outcome, complications around the irradiation areas are inevitable and the quality of life of the post-radiotherapy patients is often compromised. Trismus, which is defined as the restricted mouth opening or jaw movement due to the disorder of temporo-mandibular joint (TMJ), is one of the possible late complications for radiotherapy of NPC and is found in 5-17% of the post-radiotherapy (post-RT) patients. Trismus at early stage may only affect the speech, but in severe cases nutritional intake and oral hygiene condition may deteriorate seriously. This article reviewed the possible causes of radiation-induced TMJ damage, the various assessments including imaging modalities and possible treatments. The conclusion is that the availability of simple, yet effective examinations for trismus is essential for delaying the progression and restoring TMJ functions. Although there is no absolutely effective treatment for trismus, many supportive, restorative and palliative management are possible under different clinical situations.

Characterization of iris pattern stretches and application to the measurement of roll axis eye movements.

PubMed

Nishiyama, Junpei; Hashimoto, Tsutomu; Sakashita, Yusuke; Fujiyoshi, Hironobu; Hirata, Yutaka

2008-01-01

Eye movements are utilized in many scientific studies as a probe that reflects the neural representation of 3 dimensional extrapersonal space. This study proposes a method to accurately measure the roll component of eye movements under the conditions in which the pupil diameter changes. Generally, the iris pattern matching between a reference and a test iris image is performed to estimate roll angle of the test image. However, iris patterns are subject to change when the pupil size changes, thus resulting in less accurate roll angle estimation if the pupil sizes in the test and reference images are different. We characterized non-uniform iris pattern contraction/expansion caused by pupil dilation/constriction, and developed an algorithm to convert an iris pattern with an arbitrary pupil size into that with the same pupil size as the reference iris pattern. It was demonstrated that the proposed method improved the accuracy of the measurement of roll eye movement by up to 76.9%.

Restoration of movement patterns of the Hawaiian Goose

USGS Publications Warehouse

Hess, Steven C.; Leopold, Christina R.; Misajon, Kathleen; Hu, Darcy; Jeffrey, John J.

2012-01-01

We used visual observations of banded individuals and satellite telemetry from 2007 to 2011 on Hawai′i Island to document movement patterns of the Hawaiian Goose (Branta sandvicensis), commonly known as Nene. Visual observations of numbered leg bands identified >19% and ≤10% of 323 geese at one of two breeding sites and one of two distant non-breeding areas during 2007-2011. We used satellite telemetry to document movement patterns of 10 male Nene from 2009 to 2011, and log-linear models to quantify the magnitude and individual differences in altitudinal migration. Two subpopulations of Nene moved 974.4 m (95% CI ± 22.0) and 226.4 m (95% CI ± 40.7) in elevation between seasons on average, from high-elevation shrublands during the non-breeding season of May-August, to lower-elevation breeding and molting areas in September-April. Traditional movement patterns were thought to be lost until recently, but the movement pattern we documented with satellite telemetry was similar to altitudinal migration described by early naturalists in Hawai′i prior to the severe population decline of Nene in the 20th century.

Human sperm pattern of movement during chemotactic re-orientation towards a progesterone source

PubMed Central

Blengini, Cecilia Soledad; Teves, Maria Eugenia; Uñates, Diego Rafael; Guidobaldi, Héctor Alejandro; Gatica, Laura Virginia; Giojalas, Laura Cecilia

2011-01-01

Human spermatozoa may chemotactically find out the egg by following an increasing gradient of attractant molecules. Although human spermatozoa have been observed to show several of the physiological characteristics of chemotaxis, the chemotactic pattern of movement has not been easy to describe. However, it is apparent that chemotactic cells may be identified while returning to the attractant source. This study characterizes the pattern of movement of human spermatozoa during chemotactic re-orientation towards a progesterone source, which is a physiological attractant candidate. By means of videomicroscopy and image analysis, a chemotactic pattern of movement was identified as the spermatozoon returned towards the source of a chemotactic concentration of progesterone (10 pmol l−1). First, as a continuation of its original path, the spermatozoon swims away from the progesterone source with linear movement and then turns back with a transitional movement that can be characterized by an increased velocity and decreased linearity. This sperm behaviour may help the spermatozoon to re-orient itself towards a progesterone source and may be used to identify the few cells that are undergoing chemotaxis at a given time. PMID:21765441

The relationship between control, kinematic and electromyographic variables in fast single-joint movements in humans.

PubMed

Feldman, A G; Adamovich, S V; Levin, M F

1995-01-01

Two versions of the hypothesis that discrete movements are produced by shifts in the system's equilibrium point are considered. The first suggests that shifts are monotonic and end near the peak velocity of movement, and the second presumes that they are nonmonotonic ("N-shaped") and proceed until the end of movement. The first version, in contrast to the second, predicts that movement time may be significantly reduced by opposing loads without changes in the control pattern. The purpose of the present study was to test the two hypotheses about the duration and shape of the shift in the equilibrium point based on their respective predictions concerning the effects of perturbations on kinematic and EMG patterns in fast elbow flexor movements. Subjects performed unopposed flexions of about 55-70 degrees (control trials) and, in random test trials, movements were opposed by spring-like loads generated by a torque motor. Subjects had no visual feedback and were instructed not to correct arm deflections in case of perturbations. After the end of the movement, the load was removed leading to a secondary movement to the same final position as that in control trials (equifinality). When the load was varied, the static arm positions before unloading and associated joint torques (ranging from 0 to 80-90% of maximum voluntary contraction) had a monotonic relationship. Test movements opposed by a high load (80-90% of maximal voluntary contraction) ended near the peak velocity of control movements. Phasic and tonic electromyographic patterns were load-dependent. In movements opposed by high loads, the first agonist burst was significantly prolonged and displayed a high level of tonic activity for as long as the load was maintained. In the same load conditions, the antagonist burst was suppressed during the dynamic and static phases of movement. The findings of suppression of the antagonist burst does not support the hypothesis of an N-shaped control signal. Equally, the substantial reduction in movement time by the introduction of an opposing load cannot be reconciled in this model. Instead, our data indicate that the shifts in the equilibrium point underlying fast flexor movements are of short duration, ending near the peak velocity of unopposed movement. This suggests that kinematic and electromyographic patterns represent a long-lasting oscillatory response of the system to the short-duration monotonic control pattern, external forces and proprioceptive feedback.

Physiological Motion and Registration of Abnormalities in Liver During Focused Ultrasound Surgery

NASA Astrophysics Data System (ADS)

Chauhan, Sunita; Rh, Abhilash

Continuous deformation and dislocation of soft tissues in the abdominal and thoracic region presents a major issue for effective targeting of all non-invasive ablative modalities such as radiotherapy/surgery and Focused Ultrasound Surgery. Most significant among these is the movement of the target organs due to physiological processes such as respiration. The movement is found to be most significant for liver and kidneys. We studied movement and compensation strategies with the aim to implement them during ultrasound ablation using our robotic system for targeted FUS dose delivery. The motion pattern of the liver can be assumed to be in a single plane as it closely follows the movement of the diaphragm. However, the movement of kidneys is three dimensional and follows complicated patterns. Kidney motion is highly subject specific and has poor repeatability. In our research, we quantify the relation of liver movement and the breathing pattern so as to achieve real-time movement compensation using a prediction-correlation approach.

Effect of mini-implant-supported mandibular overdentures on electromyographic activity of the masseter muscle during chewing of hard and soft food.

PubMed

Ashmawy, Tarek Mohy; El Talawy, Dina Bahgat; Shaheen, Nasser Hussein

2014-09-01

To objectively evaluate the effect of mini-implant- supported mandibular overdentures on electromyographic activity (EMG) of the masseter muscle during chewing of hard and soft foods. Twelve completely edentulous patients (4 females and 8 males) with maladaptive experience of wearing mandibular dentures received new maxillary and mandibular dentures. After 3 months of adaptation, four mini dental implants (MDIs) were inserted in the interforaminal region of the mandible, and the new mandibular dentures were connected to the implants immediately with O/ring attachments. The activity of masseter muscle (EMG) and the duration of chewing cycle were measured during chewing hard (carrot) and soft (gum) foods. The measurements were made 3 months after wearing each of the following prostheses: the new conventional dentures; and the MDI-retained mandibular overdentures. The EMG of masseter muscle increased and the DC decreased with MDI-retained mandibular overdentures when compared to conventional dentures. Hard food (carrot) was associated with increased EMG and decreased DC when compared to soft food (gum) for both conventional dentures and MDI-retained mandibular overdentures. Mini-implant-supported mandibular overdentures are associated with increased activity of masseter muscle and decreased duration of chewing cycle for both hard and soft foods when compared to conventional dentures.

[Needle breakage during mandibular block anaesthesia: prevention and retrieval].

PubMed

Baart, J A; van Amerongen, W E; de Jong, K J M; Allard, R H B

2006-12-01

Disposable needles for dental local anaesthesia do not break easily. Still, needle breakage does occur, and is mainly caused by unexpected movements of the patient or pre-use bending of the needle by the dentist. If a dental needle breaks while administering local anaesthesia, the dentist should prevent panic. If the patient opens his mouth wide the needle might still be visible. If so, the needle is removed. If the needle is no longer visible, the site where the needle has penetrated the mucosa should be marked with a permanent marker. The dentist will contact a maxillofacial surgeon for immediate consultation. The maxillofacial surgeon will try to retrieve the broken dental needle under general anaesthesia.

Efficacy of clear aligners in controlling orthodontic tooth movement: a systematic review.

PubMed

Rossini, Gabriele; Parrini, Simone; Castroflorio, Tommaso; Deregibus, Andrea; Debernardi, Cesare L

2015-09-01

To assess the scientific evidence related to the efficacy of clear aligner treatment (CAT) in controlling orthodontic tooth movement. PubMed, PMC, NLM, Embase, Cochrane Central Register of Controlled Clinical Trials, Web of Knowledge, Scopus, Google Scholar, and LILACs were searched from January 2000 to June 2014 to identify all peer-reviewed articles potentially relevant to the review. Methodological shortcomings were highlighted and the quality of the studies was ranked using the Cochrane Tool for Risk of Bias Assessment. Eleven relevant articles were selected (two Randomized Clinical Trials (RCT), five prospective non-randomized, four retrospective non-randomized), and the risk of bias was moderate for six studies and unclear for the others. The amount of mean intrusion reported was 0.72 mm. Extrusion was the most difficult movement to control (30% of accuracy), followed by rotation. Upper molar distalization revealed the highest predictability (88%) when a bodily movement of at least 1.5 mm was prescribed. A decrease of the Little's Index (mandibular arch: 5 mm; maxillary arch: 4 mm) was observed in aligning arches. CAT aligns and levels the arches; it is effective in controlling anterior intrusion but not anterior extrusion; it is effective in controlling posterior buccolingual inclination but not anterior buccolingual inclination; it is effective in controlling upper molar bodily movements of about 1.5 mm; and it is not effective in controlling rotation of rounded teeth in particular. However, the results of this review should be interpreted with caution because of the number, quality, and heterogeneity of the studies.

Thin-plate spline analysis of mandibular growth.

PubMed

Franchi, L; Baccetti, T; McNamara, J A

2001-04-01

The analysis of mandibular growth changes around the pubertal spurt in humans has several important implications for the diagnosis and orthopedic correction of skeletal disharmonies. The purpose of this study was to evaluate mandibular shape and size growth changes around the pubertal spurt in a longitudinal sample of subjects with normal occlusion by means of an appropriate morphometric technique (thin-plate spline analysis). Ten mandibular landmarks were identified on lateral cephalograms of 29 subjects at 6 different developmental phases. The 6 phases corresponded to 6 different maturational stages in cervical vertebrae during accelerative and decelerative phases of the pubertal growth curve of the mandible. Differences in shape between average mandibular configurations at the 6 developmental stages were visualized by means of thin-plate spline analysis and subjected to permutation test. Centroid size was used as the measure of the geometric size of each mandibular specimen. Differences in size at the 6 developmental phases were tested statistically. The results of graphical analysis indicated a statistically significant change in mandibular shape only for the growth interval from stage 3 to stage 4 in cervical vertebral maturation. Significant increases in centroid size were found at all developmental phases, with evidence of a prepubertal minimum and of a pubertal maximum. The existence of a pubertal peak in human mandibular growth, therefore, is confirmed by thin-plate spline analysis. Significant morphological changes in the mandible during the growth interval from stage 3 to stage 4 in cervical vertebral maturation may be described as an upward-forward direction of condylar growth determining an overall "shrinkage" of the mandibular configuration along the measurement of total mandibular length. This biological mechanism is particularly efficient in compensating for major increments in mandibular size at the adolescent spurt.

Three-Dimensional Analysis of Mandibular Angle Classification and Aesthetic Evaluation of the Lower Face in Chinese Female Adults.

PubMed

Mao, Xiaoyan; Fu, Xi; Niu, Feng; Chen, Ying; Jin, Qi; Qiao, Jia; Gui, Lai

2018-05-14

Reduction gonioplasty is very popular in East Asia. However, there has been little quantitative criteria for mandibular angle classification or aesthetics. The aim of this study was to investigate the quantitative differences of mandibular angle types and determine the morphologic features of mandibular angle in attractive women. We created a database of skull computed tomography and standardized frontal and lateral photographs of 96 Chinese female adults. Mandibular angle was classified into 3 groups, namely, extraversion, introversion, and healthy group, based on the position of gonion. We used a 5-point Likert scale to quantify attractiveness based on photographs. Those who scored 4 or higher were defined as attractive women. Three types of computed tomography measurements of the mandible were taken, including 4 distances, 4 angles, and 3 proportions. Discriminant analysis was applied to establish a mathematic model for mandibular angle aesthetics evaluation. Significant differences were observed between the different types of mandibular angle in lower facial width (Gol-Gor), mandibular angle (Co-Go-Me), and gonion divergence angle (Gol-Me-Gor) (P < 0.01). Chinese attractive women had a mandibular angle of 123.913 ± 2.989 degrees, a FH-MP of 27.033 ± 2.695 degrees, and a Go-Me/Co-Go index of 2.0. The "healthy" women had a mandibular angle of 116.402 ± 5.373 degrees, a FH-MP of 19.556 ± 5.999 degrees, and a Go-Me/Co-Go index of 1.6. The estimated Fisher linear discriminant function for the identification of attractive women was as follows: Y = -0.1516X1(Co-Go) + 0.128X2(Go-Me) + 0.04936X3(Co-Go-Me) +0.0218X4(FH-MP). Our study quantified the differences of mandibular angle types and identified the morphological features of mandibular angle in attractive Chinese female adults. Our results could assist plastic surgeons in presurgical designing of new aesthetic gonion and help to evaluate lower face aesthetics.

Mandibular marginal contouring in oriental aesthetic surgery: refined surgical concept and operative procedure.

PubMed

Satoh, Kaneshige; Mitsukawa, Nobuyuki

2014-05-01

In aesthetic mandibular contouring surgery, which is often conducted in Asians, the operative procedure is thought to deliver a more aesthetic mandibular shape by means of contouring conducted as a whole from the ramus to the symphysis. The authors describe the refined concept and operative procedures of mandibular marginal contouring. For the 7-year period from 2004 to 2011, mandibular marginal contouring has been used in 57 consecutive series of Japanese subjects. Patient ages ranged from 18 to 33 years, and the subjects included 15 men and 42 women. The surgery was carried out by cutting off the protruding deformed mandibular margin from the ramus to the symphysis. In 53 of 57 cases, the focus was on angle contouring. Concomitant genioplasty by horizontal osteotomy of the chin was conducted in 42 of 57 cases (recession, advancement, shortening, elongation, and correction of the shift variously). In 22 materials exhibiting bulk around the mandibular, the ramus to the body was excised sagittally and thinned. In all the patients, mandibular marginal contouring from the ramus to the symphysis was completed. Partial masseter muscle resection was conducted in 11 of 57 cases. Mandibular contouring effectively achieved a highly satisfactory result in all cases. The upper portion of the peripheral branch of the trunk of the mental nerve was dissected by an electric scalpel in 1 case but sutured immediately using an 8-0 nylon stitch. Transient palsy of the mental nerve was noticed in a few cases but subsided in 1 to 2 months. No particular complications were encountered. No secondary revision was required in this series. In mandibular angle plasty, mandibular marginal contouring from the ramus to the symphysis should be carried out by cutting off the angle keeping in mind the entire mandibular shape. This concept and the procedure can deliver greater patient satisfaction.

Movements of wintering surf scoters: Predator responses to different prey landscapes

USGS Publications Warehouse

Kirk, M.; Esler, Daniel N.; Iverson, S.A.; Boyd, W.S.

2008-01-01

The distribution of predators is widely recognized to be intimately linked to the distribution of their prey. Foraging theory suggests that predators will modify their behaviors, including movements, to optimize net energy intake when faced with variation in prey attributes or abundance. While many studies have documented changes in movement patterns of animals in response to temporal changes in food, very few have contrasted movements of a single predator species naturally occurring in dramatically different prey landscapes. We documented variation in the winter movements, foraging range size, site fidelity, and distribution patterns of a molluscivorous sea duck, the surf scoter (Melanitta perspicillata), in two areas of coastal British Columbia with very different shellfish prey features. Baynes Sound has extensive tidal flats with abundant clams, which are high-quality and temporally stable prey for scoters. Malaspina Inlet is a rocky fjord-like inlet where scoters consume mussels that are superabundant and easily accessible in some patches but are heavily depleted over the course of winter. We used radio telemetry to track surf scoter movements in both areas and found that in the clam habitats of Baynes Sound, surf scoters exhibited limited movement, small winter ranges, strong foraging site fidelity, and very consistent distribution patterns. By contrast, in mussel habitats in the Malaspina Inlet, surf scoters displayed more movement, larger ranges, little fidelity to specific foraging sites, and more variable distribution patterns. We conclude that features associated with the different prey types, particularly the higher depletion rates of mussels, strongly influenced seasonal space use patterns. These findings are consistent with foraging theory and confirm that predator behavior, specifically movements, is environmentally mediated. ?? 2008 Springer-Verlag.

Bridging the gulf between correlated random walks and Lévy walks: autocorrelation as a source of Lévy walk movement patterns.

PubMed

Reynolds, Andy M

2010-12-06

For many years, the dominant conceptual framework for describing non-oriented animal movement patterns has been the correlated random walk (CRW) model in which an individual's trajectory through space is represented by a sequence of distinct, independent randomly oriented 'moves'. It has long been recognized that the transformation of an animal's continuous movement path into a broken line is necessarily arbitrary and that probability distributions of move lengths and turning angles are model artefacts. Continuous-time analogues of CRWs that overcome this inherent shortcoming have appeared in the literature and are gaining prominence. In these models, velocities evolve as a Markovian process and have exponential autocorrelation. Integration of the velocity process gives the position process. Here, through a simple scaling argument and through an exact analytical analysis, it is shown that autocorrelation inevitably leads to Lévy walk (LW) movement patterns on timescales less than the autocorrelation timescale. This is significant because over recent years there has been an accumulation of evidence from a variety of experimental and theoretical studies that many organisms have movement patterns that can be approximated by LWs, and there is now intense debate about the relative merits of CRWs and LWs as representations of non-orientated animal movement patterns.

Temporomandibular joint formation requires two distinct hedgehog-dependent steps.

PubMed

Purcell, Patricia; Joo, Brian W; Hu, Jimmy K; Tran, Pamela V; Calicchio, Monica L; O'Connell, Daniel J; Maas, Richard L; Tabin, Clifford J

2009-10-27

We conducted a genetic analysis of the developing temporo-mandibular or temporomandi-bular joint (TMJ), a highly specialized synovial joint that permits movement and function of the mammalian jaw. First, we used laser capture microdissection to perform a genome-wide expression analysis of each of its developing components. The expression patterns of genes identified in this screen were examined in the TMJ and compared with those of other synovial joints, including the shoulder and the hip joints. Striking differences were noted, indicating that the TMJ forms via a distinct molecular program. Several components of the hedgehog (Hh) signaling pathway are among the genes identified in the screen, including Gli2, which is expressed specifically in the condyle and in the disk of the developing TMJ. We found that mice deficient in Gli2 display aberrant TMJ development such that the condyle loses its growth-plate-like cellular organization and no disk is formed. In addition, we used a conditional strategy to remove Smo, a positive effector of the Hh signaling pathway, from chondrocyte progenitors. This cell autonomous loss of Hh signaling allows for disk formation, but the resulting structure fails to separate from the condyle. Thus, these experiments establish that Hh signaling acts at two distinct steps in disk morphogenesis, condyle initiation, and disk-condyle separation and provide a molecular framework for future studies of the TMJ.

Temporomandibular joint formation requires two distinct hedgehog-dependent steps

PubMed Central

Purcell, Patricia; Joo, Brian W.; Hu, Jimmy K.; Tran, Pamela V.; Calicchio, Monica L.; O'Connell, Daniel J.; Maas, Richard L.; Tabin, Clifford J.

2009-01-01

We conducted a genetic analysis of the developing temporo-mandibular or temporomandi-bular joint (TMJ), a highly specialized synovial joint that permits movement and function of the mammalian jaw. First, we used laser capture microdissection to perform a genome-wide expression analysis of each of its developing components. The expression patterns of genes identified in this screen were examined in the TMJ and compared with those of other synovial joints, including the shoulder and the hip joints. Striking differences were noted, indicating that the TMJ forms via a distinct molecular program. Several components of the hedgehog (Hh) signaling pathway are among the genes identified in the screen, including Gli2, which is expressed specifically in the condyle and in the disk of the developing TMJ. We found that mice deficient in Gli2 display aberrant TMJ development such that the condyle loses its growth-plate-like cellular organization and no disk is formed. In addition, we used a conditional strategy to remove Smo, a positive effector of the Hh signaling pathway, from chondrocyte progenitors. This cell autonomous loss of Hh signaling allows for disk formation, but the resulting structure fails to separate from the condyle. Thus, these experiments establish that Hh signaling acts at two distinct steps in disk morphogenesis, condyle initiation, and disk–condyle separation and provide a molecular framework for future studies of the TMJ. PMID:19815519

Segregation or aggregation? Sex-specific patterns in the seasonal occurrence of white sharks Carcharodon carcharias at the Neptune Islands, South Australia.

PubMed

Bruce, B; Bradford, R

2015-12-01

The seasonal patterns of occurrence of male and female white sharks Carcharodon carcharias at the Neptune Islands in South Australia were reviewed. Analyses of a 14 year data series indicate that females seasonally aggregate in late autumn and winter coinciding with the maximum in-water availability of lactating female long-nose fur seals and seal pups. During this period, observed male:female sex ratios were similar; whereas during late spring and summer, males continued to visit, but females were rarely recorded. There was no evidence for segregation by sex or size at the Neptunes, but the highly focused seasonal pattern of occurrence of females compared with the year-round records of males suggests that there are likely to be differences between the sexes in overall distribution and movement patterns across southern Australia. It is suggested that foraging strategies and prey selection differ between sexes in C. carcharias across the life-history stages represented and that sex-specific foraging strategies may play an important role in structuring movement patterns and the sex ratios observed at such aggregation sites. Differences between sexes in distribution, movement patterns and foraging strategies are likely to have implications for modelling the consequences of fisheries by-catch between regions or jurisdictions and other spatially or temporally discrete anthropogenic effects on C. carcharias populations. Such differences urge for caution when estimating the size of C. carcharias populations based on observations at pinniped colonies due to the likelihood of sex-specific differences in movements and patterns of residency. These differences also suggest a need to account for sex-specific movement patterns and distribution in population and movement models as well as under conservation actions. © 2015 The Fisheries Society of the British Isles.

Identifying Movement Patterns and Severity of Associated Pain in Sign Language Interpreters

ERIC Educational Resources Information Center

Freeman, Julie K.; Rogers, Janet L.

2010-01-01

Our research sought to identify the most common movement patterns and postures performed by sign language interpreters and the frequency and severity of any pain that may be associated with the movements. A survey was developed and mailed to registered sign language interpreters throughout the state of Illinois. For each specific upper extremity…

Winter movements of Louisiana pine snakes (Pituophis ruthveni) in Texas and Louisiana

Treesearch

Josh B. Pierce; D. Craig Rudolph; Shirley J. Burgdorf; Richard R. Schaefer; Richard N. Conner; John G. Himes; C. Mike Duran; Laurence M. Hardy; Robert R. Fleet

2014-01-01

Despite concerns that the Louisiana Pine Snake (Pituophis ruthveni) has been extirpated from large portions of its historic range, only a limited number of studies on their movement patterns have been published. Winter movement patterns are of particular interest since it has been hypothesized that impacts of management practices would be reduced during the winter....

Hand Movements and Braille Reading Efficiency: Data from the Alphabetic Braille and Contracted Braille Study

ERIC Educational Resources Information Center

Wright, Tessa; Wormsley, Diane P.; Kamei-Hannan, Cheryl

2009-01-01

Using a subset of data from the Alphabetic Braille and Contracted Braille Study, researchers analyzed the patterns and characteristics of hand movements as predictors of reading performance. Statistically significant differences were found between one- and two-handed readers and between patterns of hand movements and reading rates. (Contains 6…

Attention Switching during Scene Perception: How Goals Influence the Time Course of Eye Movements across Advertisements

ERIC Educational Resources Information Center

Wedel, Michel; Pieters, Rik; Liechty, John

2008-01-01

Eye movements across advertisements express a temporal pattern of bursts of respectively relatively short and long saccades, and this pattern is systematically influenced by activated scene perception goals. This was revealed by a continuous-time hidden Markov model applied to eye movements of 220 participants exposed to 17 ads under a…

The Use of Census Migration Data to Approximate Human Movement Patterns across Temporal Scales

PubMed Central

Wesolowski, Amy; Buckee, Caroline O.; Pindolia, Deepa K.; Eagle, Nathan; Smith, David L.; Garcia, Andres J.; Tatem, Andrew J.

2013-01-01

Human movement plays a key role in economies and development, the delivery of services, and the spread of infectious diseases. However, it remains poorly quantified partly because reliable data are often lacking, particularly for low-income countries. The most widely available are migration data from human population censuses, which provide valuable information on relatively long timescale relocations across countries, but do not capture the shorter-scale patterns, trips less than a year, that make up the bulk of human movement. Census-derived migration data may provide valuable proxies for shorter-term movements however, as substantial migration between regions can be indicative of well connected places exhibiting high levels of movement at finer time scales, but this has never been examined in detail. Here, an extensive mobile phone usage data set for Kenya was processed to extract movements between counties in 2009 on weekly, monthly, and annual time scales and compared to data on change in residence from the national census conducted during the same time period. We find that the relative ordering across Kenyan counties for incoming, outgoing and between-county movements shows strong correlations. Moreover, the distributions of trip durations from both sources of data are similar, and a spatial interaction model fit to the data reveals the relationships of different parameters over a range of movement time scales. Significant relationships between census migration data and fine temporal scale movement patterns exist, and results suggest that census data can be used to approximate certain features of movement patterns across multiple temporal scales, extending the utility of census-derived migration data. PMID:23326367

To Evaluate the Correlation Between Skeletal and Dental Parameters to the Amount of Crowding in Class II Div. 1 Malocclusions.

PubMed

Singh, Shivani; Shivaprakash, G

2017-09-01

Crowding of teeth is one of the most common problem that motivates the patient to seek orthodontic treatment. Determination of etiology of crowding could have a significant effect on treatment planning and prognosis of Class II malocclusion. Aim of this study was to evaluate the relationship of skeletal and dental parameters to amount of dental crowding in patients with Class II Divison 1 (div.1) malocclusion. Pretreatment lateral cephalograms and dental casts of 60 patients with skeletal Class II malocclusion were collected for the study. The sample was divided into two groups according to severity of pretreatment mandibular crowding. Group I consisted of cases with crowding ≥3 mm and Group II with crowding <3 mm. Lateral cephalograms for each patient was manually traced and skeletal parameters (effective maxillary and mandibular length, mandibular plane angle, Y Axis, lower anterior face height) and dental parameters (axial inclination of lower incisor, inclination of lower incisor to mandibular plane, interincisal angle) were measured. Unpaired t-test was used for intergroup comparison and relationship between different measurements was investigated using Pearson correlation coefficient. Among the skeletal parameters measured, only effective mandibular length exhibited statistically significant difference between the two groups. No statistically significant difference was found between the two groups for any of the dental parameters. Significant inverse correlation was found between mandibular crowding and effective mandibular length. Subjects with Class II div.1 malocclusion and moderate to severe mandibular crowding have significantly smaller effective mandibular base length than subjects with the same malocclusion and slight mandibular crowding.

A randomized clinical trial comparing mandibular incisor proclination produced by fixed labial appliances and clear aligners.

PubMed

Hennessy, Joe; Garvey, Thérèse; Al-Awadhi, Ebrahim A

2016-09-01

To compare the mandibular incisor proclination produced by fixed labial appliances and third generation clear aligners. Patients underwent a course of orthodontic treatment using either fixed labial appliances or clear aligners (Invisalign). Mandibular incisor proclination was measured by comparing pretreatment and near-end treatment lateral cephalograms. Eligibility criteria included adult patients with mild mandibular incisor crowding (<4 mm) and Class I skeletal bases (ANB, 1-4°). The main outcome was the cephalometric change in mandibular incisor inclination to the mandibular plane at the end of treatment. Eligible patients picking a sealed opaque envelope, which indicated their group allocation, was used to achieve randomization. Data was analyzed using a Welch two-sample t-test. Forty-four patients (mean age, 26.4 ± 7.7 years) were randomized in a 1:1 ratio to either the fixed labial appliance or the clear aligner group. Baseline characteristics were similar for both groups: Fixed appliance mean crowding was 2.1 ± 1.3 mm vs clear aligner mean crowding, 2.5 ± 1.3 mm; pretreatment mean mandibular incisor inclination for the fixed appliance group was 90.8 ± 5.4° vs 91.6 ± 6.4° for the clear aligner group. Fixed appliances produced 5.3 ± 4.3° of mandibular incisor proclination. Clear aligners proclined the mandibular incisors by 3.4 ± 3.2°. The difference between the two groups was not statistically significant (P > .05). There was no difference in the amount of mandibular incisor proclination produced by clear aligners and fixed labial appliances in mild crowding cases.

Association between third molar and mandibular angle fracture: A systematic review and meta-analysis.

PubMed

Giovacchini, Francesco; Paradiso, Daniele; Bensi, Caterina; Belli, Stefano; Lomurno, Giuseppe; Tullio, Antonio

2018-04-01

The aim of this study was to investigate the risk of mandibular angle fracture associated with the presence of a mandibular third molar and its position when the mandibular fracture occurs. A systematic literary search was performed in Pubmed, Scopus, and the Cochrane Library for observational studies with at least 250 patients that included frequency of mandibular angle fracture, presence of third molar, and its position. A total of seven studies were included in the review, from an initial search of 622 titles. The relative risk of mandibular angle fracture with third molar was 1.90 (95% CI = 1.47-2.46). The relative risk of mandibular angle fracture related to third molar position (according to the Pell and Gregory classification) was 1.18 (95% CI = 0.62-2.25), 1.98 (95% CI = 0.95-4.10), 2.72 (95% CI = 1.78-4.16), 1.31 (95% CI = 0.80-2.14), 2.21 (95% CI = 1.69-2.87) and 2.99 (95% CI = 2.12-4.22) for Class A, Class B, Class C, Class I, Class II, and Class III, respectively. Our meta-analysis reported a two-fold increased risk of mandibular angle fracture with the presence of a third molar in patients who presented with mandibular fractures. Even the third molar position seemed to influence mandibular angle fracture, especially Class C, Class II, and Class III. Copyright © 2017 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Movement patterns of peak-dose levodopa-induced dyskinesias in patients with Parkinson's disease.

PubMed

Gour, Jackie; Edwards, Roderick; Lemieux, Sarah; Ghassemi, Mehrdad; Jog, Mandar; Duval, Christian

2007-09-14

The present study characterized involuntary movements associated with levodopa-induced dyskinesias (LID) in patients with Parkinson's disease. We used amplitude, proportional energy, frequency dispersion and sample entropy to determine whether LID movement patterns are truly random, as clinical description seems to suggest, or possess some underlying pattern that is not visible to the naked eye. LID was captured using a magnetic tracker system, which provided 3D rendering of whole-body LID. Patients were instructed to maintain a standing position, with arms extended in front of them. We compared the measurements of the dyskinetic PD group (DPD) with 10 patients without dyskinesias (NDPD) and 10 control subjects. In comparison to the other two groups, movement patterns from the DPD group had significantly higher amplitude, confirming the presence of dyskinesias. In addition, higher frequency components in the power spectrum of velocity were detected, suggestive of higher velocity in LID movement. Furthermore, there was a concentration in narrow frequency bands, which suggested stable oscillatory activity. Finally, sample entropy revealed more regularity in the DPD group. Although not statistically significant, we found that the amplitude from the NDPD group had a tendency to be smaller than those of controls. As well, the spectra were often more dispersed for the NDPD group. In conclusion, the present results suggest that LID cannot be considered as purely random movement since they possess some deterministic pattern of motion. This may provide a way for patients to adapt to these involuntary movements while performing voluntary motor acts.

Influence of adequate pelvic floor muscle contraction on the movement of the coccyx during pelvic floor muscle training.

PubMed

Fujisaki, Akiko; Shigeta, Miwa; Shimoinaba, Misa; Yoshimura, Yasukuni

2018-04-01

[Purpose] Pelvic floor muscle training is a first-line therapy for female stress urinary incontinence. Previous studies have suggested that the coccyx tip moves ventrally and cranially during pelvic floor muscle contraction. The study aimed to elucidate the influence of adequate pelvic floor muscle contraction on coccyx movement. [Subjects and Methods] Sixty-three females (57 patients with stress urinary incontinence and additional 6 healthy volunteers) were enrolled. Using magnetic resonance imaging, coccyx movement was evaluated during pelvic floor muscle contraction and strain. An adequate contraction was defined as a contraction with good Oxford grading scale [≥3] and without inadequate muscle substitution patterns. [Results] Inadequate muscle substitution patterns were observed in 33 participants (52.4%). No significant difference was observed in the movement of the coccyx tip in the ventrodorsal direction between females with and without inadequate muscle substitution patterns. However, a significant increase in the movement of the coccyx tip in the cranial direction was detected in the group without inadequate muscle substitution patterns. Compared to participants with inadequate pelvic floor muscle contraction, those who had adequate pelvic floor muscle contraction exhibited significantly increased cranial movement of the coccyx. [Conclusion] Adequate pelvic floor muscle contraction can produce cranial movement of the coccyx tip.

Activity patterns of extrinsic finger flexors and extensors during movements of instructed and non-instructed fingers.

PubMed

van Beek, Nathalie; Stegeman, Dick F; van den Noort, Josien C; H E J Veeger, DirkJan; Maas, Huub

2018-02-01

The fingers of the human hand cannot be controlled fully independently. This phenomenon may have a neurological as well as a mechanical basis. Despite previous studies, the neuromechanics of finger movements are not fully understood. The aims of this study were (1) to assess the activation and coactivation patterns of finger specific flexor and extensor muscle regions during instructed single finger flexion and (2) to determine the relationship between enslaved finger movements and respective finger muscle activation. In 9 healthy subjects (age 22-29), muscle activation was assessed during single finger flexion using a 90 surface electromyography electrode grid placed over the flexor digitorum superficialis (FDS) and the extensor digitorum (ED). We found (1) no significant differences in muscle activation timing between fingers, (2) considerable muscle activity in flexor and extensor regions associated with the non-instructed fingers and (3) no correlation between the muscle activations and corresponding movement of non-instructed fingers. A clear disparity was found between the movement pattern of the non-instructed fingers and the activity pattern of the corresponding muscle regions. This suggests that mechanical factors, such as intertendinous and myofascial connections, may also affect finger movement independency and need to be taken into consideration when studying finger movement. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Correlation of Blood Glucose Concentration and the Movement of Laser Secondary Speckle Pattern of the Artery

NASA Astrophysics Data System (ADS)

Saputra, M. A.; Prajitno, P.

2018-04-01

Blood glucose is the molecule needed for human life, it usually measured invasively (by taking blood). but that measurement is still very vulnerable. The alternative method namely the non-invasive method is very interesting. In addition, the article [1] explains the relationship between the movement of the arterial pulse with glucose concentration, therefore the research study to investigate the correlation between the blood glucose and the movement of laser speckle pattern resulted from the arterial movement will be promising as the non-invasive method for measuring the blood glucose concentration. In this study, the laser speckle pattern imaging method, where the microscopically movement of the object is illuminated by a laser beam and recorded by the high-speed camera in a certain interval time, are used to identify the movement patterns of the artery. From the image processing, the graphs such as electrocardiograph (ECG) can be extracted. The average of the maximum peaks of the graph can be correlated with the blood glucose concentration in the blood, as the same as shown in the article [2]. From the data that has been obtained in this research, the movement of the speckle tends to increase in accordance with the rise of blood glucose concentration.

Mandibular reconstruction using plates prebent to fit rapid prototyping 3-dimensional printing models ameliorates contour deformity.

PubMed

Azuma, Masaki; Yanagawa, Toru; Ishibashi-Kanno, Naomi; Uchida, Fumihiko; Ito, Takaaki; Yamagata, Kenji; Hasegawa, Shogo; Sasaki, Kaoru; Adachi, Koji; Tabuchi, Katsuhiko; Sekido, Mitsuru; Bukawa, Hiroki

2014-10-23

Recently, medical rapid prototyping (MRP) models, fabricated with computer-aided design and computer-aided manufacture (CAD/CAM) techniques, have been applied to reconstructive surgery in the treatment of head and neck cancers. Here, we tested the use of preoperatively manufactured reconstruction plates, which were produced using MRP models. The clinical efficacy and esthetic outcome of using these products in mandibular reconstruction was evaluated. A series of 28 patients with malignant oral tumors underwent unilateral segmental resection of the mandible and simultaneous mandibular reconstruction. Twelve patients were treated with prebent reconstruction plates that were molded to MRP mandibular models designed with CAD/CAM techniques and fabricated on a combined powder bed and inkjet head three-dimensional printer. The remaining 16 patients were treated using conventional reconstruction methods. The surgical and esthetic outcomes of the two groups were compared by imaging analysis using post-operative panoramic tomography. The mandibular symmetry in patients receiving the MRP-model-based prebent plates was significantly better than that in patients receiving conventional reconstructive surgery. Patients with head and neck cancer undergoing reconstructive surgery using a prebent reconstruction plate fabricated according to an MRP mandibular model showed improved mandibular contour compared to patients undergoing conventional mandibular reconstruction. Thus, use of this new technology for mandibular reconstruction results in an improved esthetic outcome with the potential for improved quality of life for patients.

Effect of removable functional appliances on mandibular length in patients with class II with retrognathism: systematic review and meta-analysis.

PubMed

Santamaría-Villegas, Adriana; Manrique-Hernandez, Rubén; Alvarez-Varela, Emery; Restrepo-Serna, Claudia

2017-02-01

Orthopedic functional devices, are used to improve mandibular length in skeletal class II patients. However, the orthopedic functional device with the best effect to increasing the mandibular length, has not been identified before. Thus, the aim of the present investigation was to evaluate Randomized Controlled Trials (RCT), to determine the best functional appliance improving mandibular length in subjects with retrognathism. A systematic review and meta-analysis was performed, including studies published and indexed in databases between 1966 and 2016. RCTs evaluating functional appliances' effects on mandibular length (Condilion-Gnation (Co-Gn) and Condilion-Pogonion (Co-Po)), were included. Reports' structure was evaluated according to 2010 CONSORT guide. The outcome measure was distance between Co-Gn and/or Co-Po after treatment. Data were analyzed with Cochran Q Test and random effects model. Five studies were included in the meta-analysis. The overall difference in mandibular length was 1.53 mm (Confidence Interval (CI) 95% 1.15-1.92) in comparison to non-treated group. The Sander Bite Jumping reported the greatest increase in mandibular length (3.40 mm; CI 95% 1.69-5.11), followed by Twin Block, Bionator, Harvold Activator and Frankel devices. All removable functional appliances, aiming to increase mandibular length, are useful. Sander Bite Jumping was observed to be the most effective device to improve the mandibular length.

Camouflage treatment of skeletal Class III malocclusion with conventional orthodontic therapy.

PubMed

Park, Jae Hyun; Yu, Joseph; Bullen, Ryan

2017-04-01

Nonextraction camouflage treatment along with Class III elastics was used to treat a 39-year-old woman with a skeletal Class III pattern and a low mandibular plane angle and short lower anterior facial height. The total active treatment time was 26 months. Her occlusion, smile esthetics, and soft tissue profile were significantly improved after treatment. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Human mandibular shape is associated with masticatory muscle force.

PubMed

Sella-Tunis, Tanya; Pokhojaev, Ariel; Sarig, Rachel; O'Higgins, Paul; May, Hila

2018-04-16

Understanding how and to what extent forces applied to the mandible by the masticatory muscles influence its form, is of considerable importance from clinical, anthropological and evolutionary perspectives. This study investigates these questions. Head CT scans of 382 adults were utilized to measure masseter and temporalis muscle cross-sectional areas (CSA) as a surrogate for muscle force, and 17 mandibular anthropometric measurements. Sixty-two mandibles of young individuals (20-40 years) whose scans were without artefacts (e.g., due to tooth filling) were segmented and landmarked for geometric morphometric analysis. The association between shape and muscle CSA (controlled for size) was assessed using two-block partial least squares analysis. Correlations were computed between mandibular variables and muscle CSAs (all controlled for size). A significant association was found between mandibular shape and muscle CSAs, i.e. larger CSAs are associated with a wider more trapezoidal ramus, more massive coronoid, more rectangular body and a more curved basal arch. Linear measurements yielded low correlations with muscle CSAs. In conclusion, this study demonstrates an association between mandibular muscle force and mandibular shape, which is not as readily identified from linear measurements. Retrodiction of masticatory muscle force and so of mandibular loading is therefore best based on overall mandibular shape.

A patient with mandibular deviation and 3 mandibular incisors treated with asymmetrically bent improved superelastic nickel-titanium alloy wires.

PubMed

Ikeda, Yuhei; Kokai, Satoshi; Ono, Takashi

2018-01-01

Skeletal and dental discrepancies cause asymmetric malocclusions in orthodontic patients. It is difficult to achieve adequate functional occlusion and guidance in patients with congenital absence of a mandibular incisor due to the tooth-size discrepancy. Here, we describe the orthodontic treatment of a 22-year-old woman with an asymmetric Angle Class II malocclusion, mandibular deviation to the left, and 3 mandibular incisors. The anterior teeth and maxillary canines were crowded. We used an improved superelastic nickel-titanium alloy wire (Tomy International, Tokyo, Japan) to compensate for the asymmetric mandibular arch and an asymmetrically bent archwire to move the maxillary molars distally. A skeletal anchorage system provided traction for intermaxillary elastics, and extractions were not needed. We alleviated the crowding and created an ideal occlusion with proper overjet, overbite, and anterior guidance with Class I canine and molar relationships. This method of treatment with an asymmetrically bent nickel-titanium alloy wire provided proper Class I occlusion and anterior guidance despite the mandibular deviation to the left and 3 mandibular incisors, without the need for extractions. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Backward distraction osteogenesis in a patient with severe mandibular micrognathia.

PubMed

Mitsukawa, Nobuyuki; Morishita, Tadashi; Saiga, Atsuomi; Akita, Shinsuke; Kubota, Yoshitaka; Satoh, Kaneshige

2013-09-01

Maxillary skeletal prognathism can involve severe mandibular micrognathia with marked mandibular retrognathism or hypoplasia. For patients with such a condition, a conventional treatment is mandibular advancement by sagittal split ramus osteotomy (SSRO). This procedure has problems such as insufficient advancement, instability of jaw position, and postoperative relapse. Thus, in recent years, mandibular distraction osteogenesis has been used in some patients. Mandibular distraction has many advantages, but an ideal occlusion is difficult to achieve using this procedure. That is, 3-dimensional control cannot be attained using an internal device that is unidirectional. This report describes a case of severe mandibular micrognathia in a 14-year-old girl treated using backward distraction osteogenesis. This procedure was first reported by Ishii et al (Jpn J Jaw Deform 2004; 14:49) and involves a combination of SSRO and ramus distraction osteogenesis. In the present study, intermaxillary fixation in centric occlusion was performed after osteotomy, and proximal bone segments were distracted in a posterosuperior direction. This procedure is a superior surgical technique that avoids the drawbacks of SSRO and conventional mandibular distraction. However, it applies a large load to the temporomandibular joints and requires thorough management. Thus, careful evaluation needs to be made of the indication for backward distraction osteogenesis.

Movement initiation-locked activity of the anterior putamen predicts future movement instability in periodic bimanual movement.

PubMed

Aramaki, Yu; Haruno, Masahiko; Osu, Rieko; Sadato, Norihiro

2011-07-06

In periodic bimanual movements, anti-phase-coordinated patterns often change into in-phase patterns suddenly and involuntarily. Because behavior in the initial period of a sequence of cycles often does not show any obvious errors, it is difficult to predict subsequent movement errors in the later period of the cyclical sequence. Here, we evaluated performance in the later period of the cyclical sequence of bimanual periodic movements using human brain activity measured with functional magnetic resonance imaging as well as using initial movement features. Eighteen subjects performed a 30 s bimanual finger-tapping task. We calculated differences in initiation-locked transient brain activity between antiphase and in-phase tapping conditions. Correlation analysis revealed that the difference in the anterior putamen activity during antiphase compared within-phase tapping conditions was strongly correlated with future instability as measured by the mean absolute deviation of the left-hand intertap interval during antiphase movements relative to in-phase movements (r = 0.81). Among the initial movement features we measured, only the number of taps to establish the antiphase movement pattern exhibited a significant correlation. However, the correlation efficient of 0.60 was not high enough to predict the characteristics of subsequent movement. There was no significant correlation between putamen activity and initial movement features. It is likely that initiating unskilled difficult movements requires increased anterior putamen activity, and this activity increase may facilitate the initiation of movement via the basal ganglia-thalamocortical circuit. Our results suggest that initiation-locked transient activity of the anterior putamen can be used to predict future motor performance.

Environmental context explains Lévy and Brownian movement patterns of marine predators.

PubMed

Humphries, Nicolas E; Queiroz, Nuno; Dyer, Jennifer R M; Pade, Nicolas G; Musyl, Michael K; Schaefer, Kurt M; Fuller, Daniel W; Brunnschweiler, Juerg M; Doyle, Thomas K; Houghton, Jonathan D R; Hays, Graeme C; Jones, Catherine S; Noble, Leslie R; Wearmouth, Victoria J; Southall, Emily J; Sims, David W

2010-06-24

An optimal search theory, the so-called Lévy-flight foraging hypothesis, predicts that predators should adopt search strategies known as Lévy flights where prey is sparse and distributed unpredictably, but that Brownian movement is sufficiently efficient for locating abundant prey. Empirical studies have generated controversy because the accuracy of statistical methods that have been used to identify Lévy behaviour has recently been questioned. Consequently, whether foragers exhibit Lévy flights in the wild remains unclear. Crucially, moreover, it has not been tested whether observed movement patterns across natural landscapes having different expected resource distributions conform to the theory's central predictions. Here we use maximum-likelihood methods to test for Lévy patterns in relation to environmental gradients in the largest animal movement data set assembled for this purpose. Strong support was found for Lévy search patterns across 14 species of open-ocean predatory fish (sharks, tuna, billfish and ocean sunfish), with some individuals switching between Lévy and Brownian movement as they traversed different habitat types. We tested the spatial occurrence of these two principal patterns and found Lévy behaviour to be associated with less productive waters (sparser prey) and Brownian movements to be associated with productive shelf or convergence-front habitats (abundant prey). These results are consistent with the Lévy-flight foraging hypothesis, supporting the contention that organism search strategies naturally evolved in such a way that they exploit optimal Lévy patterns.

Retrospective Study of Root Canal Configurations of Mandibular Third Molars Using CBCT- Part-II.

PubMed

Somasundaram, Pavithra; Rawtiya, Manjusha; Wadhwani, Shefali; Uthappa, Roshan; Shivagange, Vinay; Khan, Sheeba

2017-06-01

Abnormal root canal morphologies of third molars can be diagnostically and technically challenging during root canal treatment. The aim of this retrospective study was to investigate the root and canal morphology of mandibular third molars in Central India population by using Cone Beam Computed Tomography (CBCT) analysis. CBCT images of 171 mandibular third molars were observed and data regarding number of roots, number of canals, Vertucci's classification in each root, prevalence of C shaped canal, gender and topographical relation of morphology in mandibular third molar was statistically evaluated. Majority of mandibular third molars had two roots (84.2%) and three canals (64.3%). Most mesial root had Vertucci Type II (55.6%) and Vertucci Type IV (22.2%), distal root had Type I canals (87.5%). Over all prevalence of C shaped canals in mandibular third molars was 9.4%. There was a high prevalence of two rooted mandibular third molars with three canals.

[Mandibular-driven simultaneous maxillo-mandibular distraction for hemifacial microsomia with rapid prototyping technology].

PubMed

Gao, Quan-Wen; Song, Hui-Feng; Xu, Ming-Huo; Liu, Chun-Ming; Chai, Jia-Ke

2013-11-01

To explore the clinical application of mandibular-driven simultaneous maxillo-mandihular distraction to correct hemifacial microsomia with rapid prototyping technology. The patient' s skull resin model was manufactured with rapid prototyping technology. The osteotomy was designed on skull resin model. According to the preoperative design, the patients underwent Le Fort I osteotomy and mandibular ramus osteotomy. The internal mandible distractor was embedded onto the osteotomy position. The occlusal titanium pin was implanted. Distraction were carried out by mandibular-driven simultaneous maxillo-mandihular distraction 5 days after operation. The distraction in five patients was complete as designed. No infection and dysosteogenesis happened. The longest distance of distraction was 28 mm, and the shortest distance was 16 mm. The facial asymmetry deformity was significantly improved at the end of distraction. The ocelusal plane of patients obviously improved. Rapid prototyping technology is helpful to design precisely osteotomy before operation. Mandibular-driven simultaneous maxillo-mandibular distraction can correct hemifacial microsomia. It is worth to clinical application.

Elders with implant overdentures: a 22-year clinical report.

PubMed

Alsabeeha, Nabeel H M

2012-09-01

To report on the long-term survival and prosthodontic maintenance of two edentulous adults with mandibular overdentures supported by hydroxyapatite (HA)-coated implants. Mandibular implant overdentures are a successful treatment option with positive impact on the quality of life of elderly edentulous adults. Long-term survival of the implants requires continued rigorous prosthodontic maintenance. Two elderly edentulous adults with mandibular overdentures supported by 2 HA-coated implants were presented for prosthodontic rehabilitation after 22 years of placement. The implants were osseo-integrated and surviving at presentation based on accepted criteria. The mandibular implant overdentures suffered recurrent loss of retention and stability. Prosthodontic treatment involving the replacement of defective attachment systems and construction of new sets of mandibular implant overdentures opposing complete maxillary dentures is presented. The long-term survival of mandibular 2-implant overdentures requires continued prosthodontic maintenance. A conservative approach in the rehabilitation of two older edentulous adults with mandibular 2-implant overdentures was described including proper selection of attachment systems. © 2012 The Gerodontology Society and John Wiley & Sons A/S.

Retrospective Study of Root Canal Configurations of Mandibular Third Molars Using CBCT- Part-II

PubMed Central

Somasundaram, Pavithra; Wadhwani, Shefali; Uthappa, Roshan; Shivagange, Vinay; Khan, Sheeba

2017-01-01

Introduction Abnormal root canal morphologies of third molars can be diagnostically and technically challenging during root canal treatment. Aim The aim of this retrospective study was to investigate the root and canal morphology of mandibular third molars in Central India population by using Cone Beam Computed Tomography (CBCT) analysis. Materials and Methods CBCT images of 171 mandibular third molars were observed and data regarding number of roots, number of canals, Vertucci’s classification in each root, prevalence of C shaped canal, gender and topographical relation of morphology in mandibular third molar was statistically evaluated. Results Majority of mandibular third molars had two roots (84.2%) and three canals (64.3%). Most mesial root had Vertucci Type II (55.6%) and Vertucci Type IV (22.2%), distal root had Type I canals (87.5%). Over all prevalence of C shaped canals in mandibular third molars was 9.4%. Conclusion There was a high prevalence of two rooted mandibular third molars with three canals. PMID:28764294

X-cephalometric study of different parts of the upper airway space and changes in hyoid position following mandibular fractures.

PubMed

Chen, L-J; Zhao, M-C; Pan, X-F; Wei, Y-Q; Wang, D-Y

2013-09-01

This study analyses the different parts of the upper airway space and the changes in hyoid position. The results provide a clinical reference for developing timely and effective treatment programmes for patients with mandibular fractures caused by maxillofacial trauma. Standard X-cephalometric measurements of the lateral skull of 210 subjects were taken. The subjects were divided into four fracture groups: condylar, mandibular angle, mandibular body, and parasymphyseal. The radiographs of the mandibular fracture groups were compared with the normal occlusion group to analyse the upper airway space and the changes in hyoid position. Different types of fractures have different effects on the upper airway space. Bilateral mandibular body fracture and the parasymphyseal fracture have a significant influence on the lower oropharyngeal and laryngopharyngeal airway spaces, with serious obstructions severely restricting the ventilatory function of patients. Fractures at different parts of the mandibular structure are closely related to the upper airway and hyoid position.

The punctum fixum-punctum mobile model: a neuromuscular principle for efficient movement generation?

PubMed

von Laßberg, Christoph; Rapp, Walter

2015-01-01

According to the "punctum fixum-punctum mobile model" that was introduced in prior studies, for generation of the most effective intentional acceleration of a body part the intersegmental neuromuscular onset succession has to spread successively from the rotation axis (punctum fixum) toward the body part that shall be accelerated (punctum mobile). The aim of the present study was to investigate whether this principle is, indeed, fundamental for any kind of efficient rotational accelerations in general, independent of the kind of movements, type of rotational axis, the current body position, or movement direction. Neuromuscular onset succession was captured by surface electromyography of relevant muscles of the anterior and posterior muscle chain in 16 high-level gymnasts during intentional accelerating movement phases while performing 18 different gymnastics elements (in various body positions to forward and backward, performed on high bar, parallel bars, rings and trampoline), as well as during non-sport specific pivot movements around the longitudinal axis. The succession patterns to generate the acceleration phases during these movements were described and statistically evaluated based on the onset time difference between the muscles of the corresponding muscle chain. In all the analyzed movement phases, the results clearly support the hypothesized succession pattern from punctum fixum to punctum mobile. This principle was further underlined by the finding that the succession patterns do change their direction running through the body when the rotational axis (punctum fixum) has been changed (e.g., high bar or rings [hands] vs. floor or trampoline [feet]). The findings improve our understanding of intersegmental neuromuscular coordination patterns to generate intentional movements most efficiently. This could help to develop more specific methods to facilitate such patterns in particular contexts, thus allowing for shorter motor learning procedures of context-specific key movement sequences in different disciplines of sports, as well as during non-sport specific movements.

The Punctum Fixum-Punctum Mobile Model: A Neuromuscular Principle for Efficient Movement Generation?

PubMed Central

von Laßberg, Christoph; Rapp, Walter

2015-01-01

According to the “punctum fixum–punctum mobile model” that was introduced in prior studies, for generation of the most effective intentional acceleration of a body part the intersegmental neuromuscular onset succession has to spread successively from the rotation axis (punctum fixum) toward the body part that shall be accelerated (punctum mobile). The aim of the present study was to investigate whether this principle is, indeed, fundamental for any kind of efficient rotational accelerations in general, independent of the kind of movements, type of rotational axis, the current body position, or movement direction. Neuromuscular onset succession was captured by surface electromyography of relevant muscles of the anterior and posterior muscle chain in 16 high-level gymnasts during intentional accelerating movement phases while performing 18 different gymnastics elements (in various body positions to forward and backward, performed on high bar, parallel bars, rings and trampoline), as well as during non-sport specific pivot movements around the longitudinal axis. The succession patterns to generate the acceleration phases during these movements were described and statistically evaluated based on the onset time difference between the muscles of the corresponding muscle chain. In all the analyzed movement phases, the results clearly support the hypothesized succession pattern from punctum fixum to punctum mobile. This principle was further underlined by the finding that the succession patterns do change their direction running through the body when the rotational axis (punctum fixum) has been changed (e.g., high bar or rings [hands] vs. floor or trampoline [feet]). The findings improve our understanding of intersegmental neuromuscular coordination patterns to generate intentional movements most efficiently. This could help to develop more specific methods to facilitate such patterns in particular contexts, thus allowing for shorter motor learning procedures of context-specific key movement sequences in different disciplines of sports, as well as during non-sport specific movements. PMID:25822498

[Inferior hemiarthroplasty of the temporo-mandibular joint with articulated condylar prosthesis type Stryker].

PubMed

Bucur, A; Dincă, O; Totan, C; Ghită, V

2007-01-01

The optimal reconstruction of the mandible and of the temporo-mandibular joint after mandibular hemi-resection with disarticulation is still controversial in literature. This paperwork presents our experience on four cases in the reconstruction of the mandible together with the inferior arthroplasty of the temporo-mandibular joint, after the resection of extended benign tumors of the mandible, based on fibular free vascularized grafts having attached a Stryker titanium condylar prosthesis reconstructing the inferior segment of the temporo-mandibular joint. Our results for the this technique were excellent, with a functional rehabilitation very close to normal. After reviewing the various techniques and their arguments in literature, with accent on the TMJ reconstruction, we consider this method to be optimal for the reconstruction of mandibular defects in patients with neoplastic conditions.

Aplasia of the mandibular condyle associated with some orthopaedic abnormalities

PubMed Central

Canger, E M; Çelenk, P

2012-01-01

A rare case of aplasia of mandibular condyle associated with some other orthopaedic problems is presented. A 5-year-old boy attended our clinic with a chief complaint of facial asymmetry and chewing difficulty. The mandible was deviated to the left. The occlusion also showed a deflection to the left of the mandibular midline. He also had walking difficulty owing to a hip abnormality. Panoramic radiographic examination of the patient revealed that the left mandibular condyl was totally absent. The right condyle was unremarkable. His history revealed neither trauma nor any significant disease. Aplasia is a rare anomaly and means the insufficient development of the mandibular condyle. True agnesis of the mandibular condyle is extremely rare. Association of the manifestations of the patient with some orthopaedic problems makes this case interesting. PMID:22116127

Winter movement dynamics of Black Brant

USGS Publications Warehouse

Lindberg, Mark S.; Ward, David H.; Tibbitts, T. Lee; Roser, John

2007-01-01

Although North American geese are managed based on their breeding distributions, the dynamics of those breeding populations may be affected by events that occur during the winter. Birth rates of capital breeding geese may be influenced by wintering conditions, mortality may be influenced by timing of migration and wintering distribution, and immigration and emigration among breeding populations may depend on winter movement and timing of pair formation. We examined factors affecting movements of black brant (Branta bernicla nigricans) among their primary wintering sites in Mexico and southern California, USA, (Mar 1998-Mar 2000) using capture-recapture models. Although brant exhibited high probability (>0.85) of monthly and annual fidelity to the wintering sites we sampled, we observed movements among all wintering sites. Movement probabilities both within and among winters were negatively related to distance between sites. We observed a higher probability both of southward movement between winters (Mar to Dec) and northward movement between months within winters. Between-winter movements were probably most strongly affected by spatial and temporal variation in habitat quality as we saw movement patterns consistent with contrasting environmental conditions (e.g., La Niña and El Niño southern oscillation cycles). Month-to-month movements were related to migration patterns and may also have been affected by differences in habitat conditions among sites. Patterns of winter movements indicate that a network of wintering sites may be necessary for effective conservation of brant.

Winter movement dynamics of black brant

USGS Publications Warehouse

Lindberg, Mark S.; Ward, David H.; Tibbitts, T. Lee; Roser, John

2007-01-01

Although North American geese are managed based on their breeding distributions, the dynamics of those breeding populations may be affected by events that occur during the winter. Birth rates of capital breeding geese may be influenced by wintering conditions, mortality may be influenced by timing of migration and wintering distribution, and immigration and emigration among breeding populations may depend on winter movement and timing of pair formation. We examined factors affecting movements of black brant (Branta bernicla nigricans) among their primary wintering sites in Mexico and southern California, USA, (Mar 1998–Mar 2000) using capture–recapture models. Although brant exhibited high probability (>0.85) of monthly and annual fidelity to the wintering sites we sampled, we observed movements among all wintering sites. Movement probabilities both within and among winters were negatively related to distance between sites. We observed a higher probability both of southward movement between winters (Mar to Dec) and northward movement between months within winters. Between-winter movements were probably most strongly affected by spatial and temporal variation in habitat quality as we saw movement patterns consistent with contrasting environmental conditions (e.g., La Niña and El Niño southern oscillation cycles). Month-to-month movements were related to migration patterns and may also have been affected by differences in habitat conditions among sites. Patterns of winter movements indicate that a network of wintering sites may be necessary for effective conservation of brant.

Impaired positioning of the gape in whiplash-associated disorders.

PubMed

Zafar, Hamayun; Nordh, Erik; Eriksson, Per-Olof

2006-01-01

We have previously introduced a new concept for natural jaw function suggesting that "functional jaw movements" are the result of coordinated jaw and neck muscle activation, leading to simultaneous movements in the temporomandibular, atlanto-occipital and cervical spine joints. Thus, jaw function requires a healthy state of both the jaw and the neck motor systems. The aim of this study was to examine the positioning of the gape in space during maximal jaw opening at fast and slow speed in healthy as well as whiplash-associated disorders (WAD) individuals. A wireless optoelectronic technique for three-dimensional movement recording was used. Subjects were seated in an upright position, with back support up to the mid-scapular level without headrest. The position of the gape in space was defined as the vertical midpoint position of the gape at maximal jaw opening (MP). In healthy, the MP generally coincided with the reference position at the start of jaw opening. In the WAD group, the MP was significantly lower than the reference position. No sex or speed related differences were found. The results suggest that both the width and orientation of the gape in space relies on coordinated jaw and neck muscle activation and mandibular and head-neck movements. This study also suggests an association between neck pain and dysfunction following trauma, and reduced width and impaired positioning of the gape in space. Finally, the MP seems to be a useful marker in evaluation of the functional state of the jaw-neck motor system.

Application of Optical Measurement Techniques During Stages of Pregnancy: Use of Phantom High Speed Cameras for Digital Image Correlation (D.I.C.) During Baby Kicking and Abdomen Movements

NASA Technical Reports Server (NTRS)

Gradl, Paul

2016-01-01

Paired images were collected using a projected pattern instead of standard painting of the speckle pattern on her abdomen. High Speed cameras were post triggered after movements felt. Data was collected at 120 fps -limited due to 60hz frequency of projector. To ensure that kicks and movement data was real a background test was conducted with no baby movement (to correct for breathing and body motion).

Pediatric mandibular fractures.

PubMed

Thaller, S R; Mabourakh, S

1991-06-01

In spite of curiosity, facial fractures, particularly mandibular fractures, in the pediatric age group embrace only a modest proportion of facial fractures that occur within the general population. Several large series report an overall incidence of approximately 1% of all facial bone fractures. A considerable volume of literature has been generated describing the pattern of injury and treatment modalities for pediatric facial bone fractures. At our institution, which is an extremely busy university-based regional trauma center, we have witnessed a persistent escalation in the number of patients requiring repair of their facial bone fractures. During the period of January 1989 through January 1990, we treated a total of 204 patients for repair of mandible fractures. An analysis of the records of this group revealed only 3 patients who were younger than 4 years of age and 2 additional patients younger than 8 years. There were another 10 patients 17 years and younger, for a total incidence of 0.08%. Additionally, we found that within this seemingly small group, there was a surprisingly high incidence of severe, associated injuries.

‘Mystery big cats’ in the Peruvian Amazon: morphometrics solve a cryptozoological mystery

PubMed Central

Sakamoto, Manabu; Hocking, Peter; Sanchez, Gustavo

2014-01-01

Two big cat skulls procured from hunters of Yanachaga National Park, Peru, were reported as those of cats informally dubbed the ‘striped tiger’ and ‘anomalous jaguar’. Observations suggested that both skulls were distinct from those of jaguars, associated descriptions of integument did not conform to this species, and it has been implied that both represent members of one or two novel species. We sought to resolve the identity of the skulls using morphometrics. DNA could not be retrieved since both had been boiled as part of the defleshing process. We took 36 cranial and 13 mandibular measurements and added them to a database incorporating nearly 300 specimens of over 30 felid species. Linear discriminant analysis resolved both specimens as part of Panthera onca with high probabilities for cranial and mandibular datasets. Furthermore, the specimens exhibit characters typical of jaguars. If the descriptions of their patterning and pigmentation are accurate, we assume that both individuals were aberrant. PMID:24688867

Global human mandibular variation reflects differences in agricultural and hunter-gatherer subsistence strategies

PubMed Central

von Cramon-Taubadel, Noreen

2011-01-01

Variation in the masticatory behavior of hunter-gatherer and agricultural populations is hypothesized to be one of the major forces affecting the form of the human mandible. However, this has yet to be analyzed at a global level. Here, the relationship between global mandibular shape variation and subsistence economy is tested, while controlling for the potentially confounding effects of shared population history, geography, and climate. The results demonstrate that the mandible, in contrast to the cranium, significantly reflects subsistence strategy rather than neutral genetic patterns, with hunter-gatherers having consistently longer and narrower mandibles than agriculturalists. These results support notions that a decrease in masticatory stress among agriculturalists causes the mandible to grow and develop differently. This developmental argument also explains why there is often a mismatch between the size of the lower face and the dentition, which, in turn, leads to increased prevalence of dental crowding and malocclusions in modern postindustrial populations. Therefore, these results have important implications for our understanding of human masticatory adaptation. PMID:22106280

Cephalomteric changes in airway dimensions with twin block therapy in growing Class II patients

PubMed Central

Vinoth, Santhana Krishnan; Thomas, Ashwin Varghese; Nethravathy, Ramya

2013-01-01

Introduction: Myofunctional appliances are commonly used for correction of skeletal Class II malrelationship. These appliances influence craniofacial and nasopharyngeal dimensions. Objectives: The present study was done to evaluate changes in airway with twin block therapy. Materials and Methods: Cephalometric assessment of airway was done in 25 growing children in the age group of 11-13 years with Class II skeletal pattern. All the patients were treated with twin block appliance. Pre and post treatment lateral cephalograms were taken to evaluate the changes in different airway and craniofacial dimensions during the treatment period. The average treatment duration was 14.5 months. Results: Airway: A significant increase was observed in upper and lower pharyngeal width and area of bony nasopharynx. Craniofacial dimension: There was a significant increase in effective mandibular length, ramal length and mandibular plane angle. There was an increase in SNB angle, which resulted in decreased ANB angle. Conclusion: There was a definite improvement in airway dimension following twin block therapy PMID:23946570

Developmental evidence for serial homology of the vertebrate jaw and gill arch skeleton

PubMed Central

Gillis, J. Andrew; Modrell, Melinda S.; Baker, Clare V. H.

2013-01-01

Gegenbaur’s classical hypothesis of jaw-gill arch serial homology is widely cited, but remains unsupported by either paleontological evidence (e.g. a series of fossils reflecting the stepwise transformation of a gill arch into a jaw) or developmental genetic data (e.g. shared molecular mechanisms underlying segment identity in the mandibular, hyoid and gill arch endoskeletons). Here we show that nested expression of Dlx genes – the “Dlx code” that specifies upper and lower jaw identity in mammals and teleosts – is a primitive feature of the mandibular, hyoid and gill arches of jawed vertebrates. Using fate-mapping techniques, we demonstrate that the principal dorsal and ventral endoskeletal segments of the jaw, hyoid and gill arches of the skate Leucoraja erinacea derive from molecularly equivalent mesenchymal domains of combinatorial Dlx gene expression. Our data suggest that vertebrate jaw, hyoid and gill arch cartilages are serially homologous, and were primitively patterned dorsoventrally by a common Dlx blueprint. PMID:23385581

[Pathomorphology of regenerative processes in mandibular fracture after sodium succinate treatment and laser magnetotherapy in an experimental setting].

PubMed

Faustov, L A; Nedel'ko, N A; Morozova, M V

2001-01-01

Morphological reactions in tissue adjacent to mandibular angular fracture were studied in guinea pigs treated with sodium succinate and laser magnetotherapy. Due to succinate therapy the exudative component of inflammation was less expressed in comparison with the control, macrophagal reaction and neoangiogenesis were activated, the volume of damaged muscle tissue and the incidence of suppurations decreased. The number of osteoblasts increased and new bone structures acquired a lamellar pattern earlier than in the control. Sodium succinate therapy in combination with laser magnetotherapy had a more pronounced positive effect as regards activation of macrophagal reaction and neoangiogenesis and a decrease in the area of fibrosclerotic changes in the zone of damaged muscles, where newly formed myosymplasts differentiated into myotubes and even in muscle fibers. Suppuration of the wound was prevented. Bone tissue in the fracture zone formed without preliminary formation of cartilaginous tissue, which resulted in more rapid osteogenesis (lamellar bone growth in the fracture zone).

Finite element analysis of the effect of force directions on tooth movement in extraction space closure with miniscrew sliding mechanics.

PubMed

Kojima, Yukio; Kawamura, Jun; Fukui, Hisao

2012-10-01

Miniscrews placed in bone have been used as orthodontic anchorage in extraction space closure with sliding mechanics. The movement patterns of the teeth depend on the force directions. To move the teeth in a desired pattern, the appropriate direction of force must be selected. The purpose of this article is to clarify the relationship between force directions and movement patterns. By using the finite element method, orthodontic movements were simulated based on the remodeling law of the alveolar bone. The power arm length and the miniscrew position were varied to change the force directions. When the power arm was lengthened, rotation of the entire maxillary dentition decreased. The posterior teeth were effective for preventing rotation of the anterior teeth through an archwire. In cases of a high position of a miniscrew, bodily tooth movement was almost achieved. The vertical component of the force produced intrusion or extrusion of the entire dentition. Within the limits of the method, the mechanical simulations demonstrated the effect of force direction on movement patterns. Copyright © 2012 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Homeotic genes and the arthropod head: Expression patterns of the labial, proboscipedia, and Deformed genes in crustaceans and insects

PubMed Central

Abzhanov, Arhat; Kaufman, Thomas C.

1999-01-01

cDNA fragments of the homologues of the Drosophila head homeotic genes labial (lab), proboscipedia (pb), and Deformed (Dfd) have been isolated from the crustacean Porcellio scaber. Because the accumulation domains of the head homeotic complex (Hox) genes had not been previously reported for crustaceans, we studied the expression patterns of these genes in P. scaber embryos by using in situ hybridization. The P. scaber lab homologue is expressed in the developing second antennal segment and its appendages. This expression domain in crustaceans and in the homologous intercalary segment of insects suggests that the lab gene specified this metamere in the last common ancestor of these two groups. The expression domain of the P. scaber pb gene is in the posterior part of the second antennal segment. This domain, in contrast to that in insects, is colinear with the domains of other head genes in P. scaber, and it differs from the insect pb gene expression domain in the posterior mouthparts, suggesting that the insect and crustacean patterns evolved independently from a broader ancestral domain similar to that found in modern chelicerates. P. scaber Dfd is expressed in the mandibular segment and paragnaths (a pair of ventral mouthpart structures associated with the stomodeum) and differs from insects, where expression is in the mandibular and maxillary segments. Thus, like pb, Dfd shows a divergent Hox gene deployment. We conclude that homologous structures of the mandibulate head display striking differences in their underlying developmental programs related to Hox gene expression. PMID:10468590

Rhythm Pattern of Sole through Electrification of the Human Body When Walking

NASA Astrophysics Data System (ADS)

Takiguchi, Kiyoaki; Wada, Takayuki; Tohyama, Shigeki

The rhythm of automatic cyclic movements such as walking is known to be generated by a rhythm generator called CPG in the spinal cord. The measurement of rhythm characteristics in walking is considered to be important for analyzing human bipedal walking and adaptive walking on irregular terrain. In particular, the soles that contact the terrain surface perform flexible movements similar to the movement of the fins of a lungfish, which is considered to be the predecessor of land animals. The sole movements are believed to be a basic movement acquired during prehistoric times. The detailed rhythm pattern of sole motion is considered to be important. We developed a method for measuring electrification without installing device on a subject's body and footwear for stabilizing the electrification of the human body. We measured the rhythm pattern of 20 subjects including 4 infants when walking by using this system and the corresponding equipment. Therefore, we confirmed the commonality of the correlative rhythm patterns of 20 subjects. Further, with regard to an individual subject, the reproducibility of a rhythm pattern with strong correlation coefficient > 0.93 ± 0.5 (mean ± SD) concerning rhythms of trials that are differently conducted on adult subjects could be confirmed.

An Assessment of Curve of Spee in Healthy Human Permanent Dentitions: A Cross Sectional Analytical Study in a Group of Young Indian Population.

PubMed

Krishnamurthy, Sushma; Hallikerimath, Rajendra B; Mandroli, Praveenkumar S

2017-01-01

An awareness of the standard value of the maxillary and the mandibular curves of Spee may aid the clinician in developing occlusion in the sagittal plane and would be useful when providing prosthetic rehabilitation for patients with occlusal derangement. To assess and compare the radius and depth of curve of Spee in maxillary and mandibular arches in men and women, in a group of young Indian population. The study cohort consisted of 25 men and 25 women between 19 to 24 years. Impression of maxillary and mandibular arches were made with alginate. Casts were poured in die stone. Standardized digital pictures of the right side of maxillary and mandibular dental casts were made with a digital camera and transferred to a computer. Tips of the distal cusps of molars, premolars and canines of the maxilla and mandible were located. The radius and the depth of the curve of Spee were measured from the digital photographs of dental casts, with the help of 'dimension tool' in the computer software (Corel DRAW X5). Mann-Whitney test was used to analyze the difference in the curve of Spee between men and women and the difference between maxillary and mandibular arches. The mean values were as follows: a) Men: Radii of curve of Spee in the maxillary and mandibular arch were 140.22±65.98 and 109.67±46.80 respectively; depths of curve of Spee in maxillary and mandibular arch were 1.65±0.67 and 1.49±0.74 respectively; b) Women: Radii of curve of Spee in the maxillary and mandibular arch were 120.58±63.91 and 98.31±63.59 respectively; depths of curve of Spee in maxillary and mandibular arch were 1.45±0.54 and 1.40±0.61 respectively. In the mandibular arch, the difference in the radii (p=0.0467) was statistically significant between men and women. In women, the difference in radii (p=0.0467) between maxillary and mandibular arches was statistically significant. The radii and depths of curve of Spee were larger in maxillary than mandibular arches in both men and women. Also, the difference in the radii of mandibular arch was statistically significant between men and women.

Movement and spatial proximity patterns of rangeland-raised Raramuri Criollo cow-calf pairs

USDA-ARS?s Scientific Manuscript database

The objective of this study was to compare movement patterns of nursing vs. nonnursing mature cows and to characterize cow-calf proximity patterns in two herds of Raramuri Criollo cattle. Herds grazed rangeland pastures in southern New Mexico (4355 ha) and west-central Chihuahua, Mexico (633 ha)'' A...

An overlay partial denture to restore worn mandibular anterior teeth.

PubMed

Samant, Asha; DeSciscio, Peter

2014-01-01

Restoring worn anterior mandibular teeth is a challenge, especially when teeth are small, esthetics are a concern, the long-term prognosis is questionable, and/or patient finances are an issue. This article describes an alternate treatment for a patient with a collapsed bite, missing posterior mandibular teeth, an ill-fitting complete maxillary denture with poor esthetics, and irregular, worn mandibular anterior teeth.

Reorganization of finger coordination patterns through motor exploration in individuals after stroke.

PubMed

Ranganathan, Rajiv

2017-09-11

Impairment of hand and finger function after stroke is common and affects the ability to perform activities of daily living. Even though many of these coordination deficits such as finger individuation have been well characterized, it is critical to understand how stroke survivors learn to explore and reorganize their finger coordination patterns for optimizing rehabilitation. In this study, I examine the use of a body-machine interface to assess how participants explore their movement repertoire, and how this changes with continued practice. Ten participants with chronic stroke wore a data glove and the finger joint angles were mapped on to the position of a cursor on a screen. The task of the participants was to move the cursor back and forth between two specified targets on a screen. Critically, the map between the finger movements and cursor motion was altered so that participants sometimes had to generate coordination patterns that required finger individuation. There were two phases to the experiment - an initial assessment phase on day 1, followed by a learning phase (days 2-5) where participants trained to reorganize their coordination patterns. Participants showed difficulty in performing tasks which had maps that required finger individuation, and the degree to which they explored their movement repertoire was directly related to clinical tests of hand function. However, over four sessions of practice, participants were able to learn to reorganize their finger movement coordination pattern and improve their performance. Moreover, training also resulted in improvements in movement repertoire outside of the context of the specific task during free exploration. Stroke survivors show deficits in movement repertoire in their paretic hand, but facilitating movement exploration during training can increase the movement repertoire. This suggests that exploration may be an important element of rehabilitation to regain optimal function.

Relationship between fracture of mandibular condyle and absence of unerupted mandibular third molar-a retrospective study.

PubMed

Rajan, Ritesh; Verma, Dinesh Kumar; Borle, R M; Yadav, Abhilasha

2016-06-01

The purpose of the present study was to find, if there exists, a co-relation between presence of unerupted mandibular third molar and fracture of mandibular condyle. A retrospective, multicenter study was done collecting the data of all mandibular condyle fractures treated from November 2006 till August 2015. Data was collected from the patient's records and radiographs for the following information: age, sex, etiology of fracture, presence and state of lower third molars, and associated fracture. The results were subjected to statistical analysis. Out of 180 patients of condylar fracture, unerupted third molars were present in 35 (19.44 %) cases compared to 145 (80.55 %) cases of condylar fracture where the unerupted third molars were not present. The difference was statistically significant (p < 0.05). In the unerupted third molar present group, isolated bilateral condylar fracture was seen in 4 (11.4 %) cases, bilateral condylar fracture associated with other mandibular fractures in 9 (25.7 %) cases, isolated unilateral condylar fracture in 0 (0.0 %) cases, and unilateral condylar fracture associated with other mandibular fractures in 17 (48.5 %) cases and condylar fracture associated with mid face fractures in 5 (14.2 %) cases. In the unerupted third molar absent group, isolated bilateral condylar fracture was seen in 5 (3.4 %) cases, bilateral condylar fracture associated with other mandibular fractures in 30 (20.6 %) cases, isolated unilateral condylar fracture in 24 (16.5 %) cases, unilateral condylar fracture associated with other mandibular fractures in 73 (50.34 %) cases, and condylar fracture associated with mid face fractures in 13(8.96 %) cases. The difference between the groups was statistically significant (p = 0.032). This study suggests that the fractures of mandibular condylar region have a significantly higher incidence in patients without an unerupted mandibular third molar.

Two Dimensional Movement Patterns of Juvenile Winter Run and Late Fall Run Chinook Salmon at the Fremont Weir, Sacramento River, CA

DTIC Science & Technology

2017-07-01

ER D C/ EL T R- 17 -1 0 Two-Dimensional Movement Patterns of Juvenile Winter- Run and Late-Fall- Run Chinook Salmon at the Fremont Weir...default. ERDC/EL TR-17-10 July 2017 Two-Dimensional Movement Patterns of Juvenile Winter- Run and Late-Fall- Run Chinook Salmon at the Fremont Weir...Sacramento River, smaller winter- run Chinook and larger late-fall- run Chinook salmon were tagged and released into a 2D telemetry array dur- ing the

Detection of EEG-patterns associated with real and imaginary movements using detrended fluctuation analysis

NASA Astrophysics Data System (ADS)

Pavlov, Alexey N.; Runnova, Anastasiya E.; Maksimenko, Vladimir A.; Grishina, Daria S.; Hramov, Alexander E.

2018-02-01

Authentic recognition of specific patterns of electroencephalograms (EEGs) associated with real and imagi- nary movements is an important stage for the development of brain-computer interfaces. In experiments with untrained participants, the ability to detect the motor-related brain activity based on the multichannel EEG processing is demonstrated. Using the detrended fluctuation analysis, changes in the EEG patterns during the imagination of hand movements are reported. It is discussed how the ability to recognize brain activity related to motor executions depends on the electrode position.

PRINCIPLES AND PATTERNS OF BAT MOVEMENTS: FROM AERODYNAMICS TO ECOLOGY

PubMed Central

Voigt, Christian C.; Frick, Winifred F.; Holderied, Marc W.; Holland, Richard; Kerth, Gerald; Mello, Marco A. R.; Plowright, Raina K.; Swartz, Sharon; Yovel, Yossi

2018-01-01

Movement ecology as an integrative discipline has advanced associated fields because it presents not only a conceptual framework for understanding movement principles but also helps formulate predictions about the consequences of movements for animals and their environments. Here, we synthesize recent studies on principles and patterns of bat movements in context of the movement ecology paradigm. The motion capacity of bats is defined by their highly articulated, flexible wings. Power production during flight follows a U-shaped curve in relation to speed in bats yet, in contrast to birds, bats use mostly exogenous nutrients for sustained flight. The navigation capacity of most bats is dominated by the echolocation system, yet other sensory modalities, including an iron-based magnetic sense, may contribute to navigation depending on a bat’s familiarity with the terrain. Patterns derived from these capacities relate to antagonistic and mutualistic interactions with food items. The navigation capacity of bats may influence their sociality, in particular, the extent of group foraging based on eavesdropping on conspecifics’ echolocation calls. We infer that understanding the movement ecology of bats within the framework of the movement ecology paradigm provides new insights into ecological processes mediated by bats, from ecosystem services to diseases. PMID:29861509

Epidemiology of Surgically Managed Mandibular Condylar Fractures at a Tertiary Referral Hospital in Urban Southwest China.

PubMed

Thapa, Swosti; Wang, Jun; Hu, Hong-Tao; Zhang, Fu-Gui; Ji, Ping

2017-01-01

Mandibular condylar fracture is one of the commonest maxillofacial fractures treated by maxillofacial surgeons. Demography of the patients, causation, and characteristics of the fracture depends on various socio-economic factors. Hence, maxillofacial surgeons should be familiar with epidemiology of mandibular condylar fracture. This study retrospectively describes the demography, etiology, fracture characteristics, and hospital utilization of surgically treated mandibular condylar fractures in a tertiary referral hospital in urban China in past five years. Data of all patients who underwent surgical management between 2011 and 2015 were collected. This included aetiology, characteristics of fracture, time, age, sex, associated injuries, and hospital utilization of 166 patients with 208 mandibular condylar fractures. These patients had undergone open reduction and internal fixation with either miniplates or lag screws. Among the fracture of head of mandibular condyle, 21.28% of the patients had the fracture segments removed. These data were statistically analyzed to describe the epidemiology of mandibular condylar fracture. Most of the patients had unilateral mandibular condylar fractures (74.7%). Male patients (76.51%) outnumbered female patients (23.49%) in this cohort. The average age of the patients was 37 years. The fractures were mostly caused by fall from height (60.84%) and were located at the condylar neck (53.61%). Most of the patients had other associated maxillofacial injuries (71.08%) which were mostly located at symphysis and parasymphysis (44.59%). It took 12.58 +/- 0.35 days of hospitalization for the treatment. Fall from height was the most prevalent cause of mandibular condylar injury in mountainous urban China. The people at highest risk were middle-aged men. Mandibular condylar fracture was mostly located at the condylar neck and was usually associated with fracture at the symphysis and parasymphysis.

TMD symptoms and vertical mandibular symmetry in young adult orthodontic patients in North Sumatra, Indonesia: a cross-sectional study

PubMed Central

Sofyanti, Ervina; Boel, Trelia; Soegiharto, Benny; Auerkari, Elza I.

2018-01-01

Background: Temporomandibular joint disorder (TMD) includes symptoms of pain and dysfunction in the muscles of mastication and the temporomandibular joint. Differences in vertical condylar height, observed in the assessment of mandibular asymmetry, is a structural alteration that represents a risk factor for TMD. The study aimed to evaluate the association between TMD symptoms and vertical mandibular symmetry in young adult orthodontic patients in North Sumatra, Indonesia.  Methods: The cross-sectional study included 18-25-year-old (mean ± SD, 21.9 ± 2.0 years) old orthodontic patients admitted to the Dental Hospital of Universitas Sumatera Utara, Medan, between June 2016 and March 2017. Vertical mandibular asymmetry was assessed from all 106 subjects using Kjellberg’s technique from pre-treatment panoramic radiographs. The TMD symptoms were assessed by structural interviews using modified questionnaires based on Temporomandibular Disorder Diagnostic Index and Fonseca’s Anamnestic Index. Results: Of the 106 subjects, 26 (24.5% of the total) with vertical mandibular symmetry and 39 (36.8%) with vertical mandibular asymmetry were positive for TMD symptoms. By contrast, 17 patients (16.0% of the total) with vertical condylar symmetry and 24 patients (22.6%) with vertical mandibular asymmetry were regarded negative for TMD symptoms. There was no significant difference (p=0.520) in TMD symptoms based on vertical mandibular symmetry. Conclusion: The results from this studied Sumatran population indicate that there are common TMD symptoms in young adult orthodontic patients, but there is no significant association between vertical mandibular asymmetry and TMD symptoms. Further study on the development of TMD, mandibular asymmetry and treatment planning for growing patients is suggested, using longitudinal and transitional approaches.

Patient satisfaction and dissatisfaction with mandibular two-implant overdentures using different attachment systems: 5-year outcomes.

PubMed

Al-Zubeidi, Mohammed I; Alsabeeha, Nabeel H M; Thomson, W Murray; Payne, Alan G T

2012-10-01

Different attachment systems for mandibular two-implant overdentures could influence levels of patient satisfaction. Positive consensus of the majority of patients being satisfied does not preclude the possibility of dissatisfaction for some. To evaluate patient satisfaction and dissatisfaction before and after 5 years of wearing mandibular two implant overdentures using different attachment systems ; to determine the prognostic relevance of pretreatment complete denture complaints to treatment outcomes. A total of 106 edentulous participants enrolled in a clinical trial completed a preliminary self-report inventory of their original complete denture complaints.New complete maxillary dentures and mandibular two-implant overdentures were provided to each participant using one of six different attachment systems. Patient satisfaction was determined at pretreatment; at baseline with mandibular two-implant overdenture insertion; and then annually for 5 years, using visual analogue and Likert-type scales. Patient satisfaction with mandibular two-implant overdentures showed significant changes pre- to posttreatment(baseline) in all domains, but these were significant immediately and maintained without further significance for 5 years, other than pain with the overdenture. After 5 years, no significant differences were observed with all the attachment systems. Highly significant differences were found with some social and psychological aspects by the fifth year compared to baseline. Diagnostic and prognostic indicators from a pretreatment inventory identified 12 participants (13.5%) who were dissatisfied. These indicators revealed a maladaptive predisposition to mandibular two-implant overdentures. The provision of mandibular two-implant overdentures will, in the majority of patients, significantly enhance levels of patient satisfaction for 5 years, as compared to complete mandibular dentures, regardless of the attachment system. Careful evaluation of pretreatment complaints with conventional dentures can possibly identify patient dissatisfaction with mandibular two-implant overdentures [corrected]. © 2010 Wiley Periodicals, Inc.

Posterior Mandibular Ridge Resorption Associated with Different Retentive Systems for Overdentures: A 7-Year Retrospective Preliminary Study.

PubMed

Elsyad, Moustafa Abdou; Mohamed, Shahinaz Sayed; Shawky, Ahmad Fathalla

This retrospective study compared posterior mandibular residual ridge resorption with two different retentive mechanisms for overdentures after 7 years. A convenience sample of 18 edentulous men was assigned to one of two equal groups. Two implants were placed in the mandibular canine areas for each patient using the conventional two-stage surgical protocol, and the implants were splinted with a round bar 3 months later. New mandibular overdentures were then connected to the bars with clips (clip-retained overdentures, CR group) or resilient liners (resilient liner-retained overdentures, RR group). Posterior mandibular ridge resorption (PMRR) was recorded using proportional measurements and posterior area index (PAI) on panoramic radiographs taken immediately after overdenture insertion (T 0 ) and 7 years later (T 7 ). A linear regression model was used to verify the relationship between PAI and the following considerations: attachment type, age, initial mandibular ridge height, period of mandibular edentulism, number of previously worn dentures, and relining events. After 7 years, the RR group demonstrated a significantly (P = .014) higher change in PAI (0.11 ± 0.02) than the CR group (0.06 ± 0.04). The average PMRR for each mm of posterior mandibular ridge was 0.79 mm (0.11 mm/year) in the CR group and 1.4 mm (0.2 mm/year) in the RR group. Attachment type, initial mandibular ridge height, and relining times were significantly correlated with change in the PAI (P = .004, P = .035, and P = .045, respectively). Within the limitations of this preliminary study's design, it was observed that following a 7-year period of use, resilient liner attachments for bar/implant-retained overdentures appear to be associated with greater posterior mandibular ridge resorption when compared to clip attachments.

Surgical treatment of comminuted mandibular fractures using a low-profile locking mandibular reconstruction plate system

PubMed Central

Kanno, Takahiro; Sukegawa, Shintaro; Nariai, Yoshiki; Tatsumi, Hiroto; Ishibashi, Hiroaki; Furuki, Yoshihiko; Sekine, Joji

2014-01-01

Objective: The treatment of comminuted mandibular fractures is challenging due to the severity of associated injuries and the need for a careful diagnosis with adequate treatment planning. Recently, open reduction and stable internal fixation (OR-IF) with a load-bearing reconstruction plate have been advocated for reliable clinical outcomes with minimal complications. This clinical prospective study evaluated OR-IF in the surgical management of comminuted mandibular fractures with a new low-profile, thin, mandibular locking reconstruction plate. Materials and Methods: We prospectively assessed OR-IF of comminuted mandibular fractures with a low-profile locking mandibular reconstruction plate in 12 patients (nine men, three women; mean age 32.2 [range 16-71] years) between April 2010 and December 2011. The clinical characteristics and associated clinical parameters of patients were evaluated over a minimum follow-up period of 12 months. Results: Traffic accidents caused 50% of the fractures, followed by falls (25%). Four patients (33.3%) had associated midfacial maxillofacial fractures, while five patients had other mandibular fractures. Seven patients (58.3%) needed emergency surgery, mostly for airway management. Anatomical reduction of the comminuted segments re-established the mandibular skeleton in stable occlusion with rigid IF via extraoral (33.3%), intraoral (50%), or combined (16.7%) approaches. Immediate functional recovery was achieved. Sound bone healing was confirmed in all patients, with no complications such as malocclusion, surgical site infection, or malunion with a mean follow-up of 16.3 (range 12-24) months. Conclusions: OR-IF using a low-profile reconstruction plate system is a reliable treatment for comminuted mandibular fractures, enabling immediate functional recovery with good clinical results. PMID:25593862

Multifactorial etiology of Torus mandibularis: study of twins.

PubMed

Auškalnis, Adomas; Rutkūnas, Vygandas; Bernhardt, Olaf; Šidlauskas, Mantas; Šalomskienė, Loreta; Basevičienė, Nomeda

2015-01-01

The aim of this study is to investigate the multifactorial etiology of mandibular tori analyzing the influence of genetics, occlusal overload, various clinical variables and their interactions. Overall, plaster casts of 162 twins (81 twin pairs) were analyzed for the presence or absence of mandibular tori. Atypical wear facets on canine tips or incisors were recorded to diagnose bruxism. Angle Class, any kind of anterior open bite and positive, negative or flat curve of Wilson were recorded. Zygosity determination was carried out using a DNA test. Mandibular tori were found in 56.8% of the cases. In 93.6% of all monozygotic twin pairs both individuals had or did not have mandibular tori (κ=0.96±0.04; p<0.001), compared to 79.4% concordance of mandibular tori in dizygotic co-twins (κ=0.7±0.12; p<0.001). Prevalence of mandibular tori was significantly higher in the group of bruxers (67.5%) compared to non-bruxers (31.3%) (p<0.001). Significant association between mandibular tori and negative or flat curve of Wilson in the maxillary second premolars and first molars was found (OR=2.55, 95% CI (1.19-5.46), p=0.016). In all monozygotic bruxers, 97.1% showed concordance of mandibular tori presence in both co-twins compared to 78.9% dizygotic bruxers, and this difference is statistically significant (p=0.007). Our results suggest that the mandibular tori are of a multifactorial origin. Mandibular tori seem to have genetic predisposition, and may be associated with teeth grinding as well as with negative or flat CW in region of maxillary second premolar and first molar.

Seasonal movement, residency, and migratory patterns of Wilson's Snipe (Gallinago delicata)

USGS Publications Warehouse

Cline, Brittany B.; Haig, Susan M.

2011-01-01

Cross-seasonal studies of avian movement establish links between geographically distinct wintering, breeding, and migratory stopover locations, or assess site fidelity and movement between distinct phases of the annual cycle. Far fewer studies have investigated individual movement patterns within and among seasons over an annual cycle. Within western Oregon's Willamette Valley throughout 2007, we quantified intra- and interseasonal movement patterns, fidelity (regional and local), and migratory patterns of 37 radiomarked Wilson's Snipe (Gallinago delicata) to elucidate residency in a region of breeding- and wintering-range overlap. Telemetry revealed complex regional population structure, including winter residents (74%), winter transients (14%), summer residents (9%), and one year-round resident breeder (3%). Results indicated a lack of connectivity between winter and summer capture populations, some evidence of partial migration, and between-season fidelity to the region (winter-resident return; subsequent fall). Across seasons, the extent of movements and use of multiple wetland sites suggested that Wilson's Snipe were capable of exploratory movements but more regularly perceived local and fine-scale segments of the landscape as connected. Movements differed significantly by season and residency; individuals exhibited contracted movements during late winter and more expansive movements during precipitation-limited periods (late spring, summer, fall). Mean home-range size was 3.5 ± 0.93 km2 (100% minimum convex polygon [MCP]) and 1.6 ± 0.42 km2 (95% fixed kernel) and did not vary by sex; however, home range varied markedly by season (range of 100% MCPs: 1.04–7.56 km2). The results highlight the need to consider seasonal and interspecific differences in shorebird life histories and space-use requirements when developing regional wetland conservation plans.

Early extraction of the mandibular third molar in case of eruption disturbances of the second molar.

PubMed

Kavadia, S; Antoniades, K; Kaklamanos, E; Antoniades, V; Markovitsi, E; Zafiriadis, L

2003-01-01

General consensus has been reached on extracting mandibular third molars when they are involved in pathologic processes. However, early extraction is advisable in cases of eruption disturbances of the mandibular second molar, before or during orthodontic treatment. Thirty-two patients with early extraction of the mandibular third molar before or during orthodontic treatment were examined. In these cases either the presence of the third molar presented an obstacle in the eruption path of the second, or third molar germ removal was considered beneficial to the course of orthodontic treatment. Early extraction of the mandibular third molar facilitates the eruption of the second molar, especially in cases where evidence of crowding and lack of space in the posterior mandibular region exist. Orthodontic treatment may, in some cases, aggravate eruption disturbances of the second molar.

Anatomy of Mandibular Vital Structures. Part I: Mandibular Canal and Inferior Alveolar Neurovascular Bundle in Relation with Dental Implantology

PubMed Central

Wang, Hom-Lay; Sabalys, Gintautas

2010-01-01

ABSTRACT Objectives It is critical to determine the location and configuration of the mandibular canal and related vital structures during the implant treatment. The purpose of the present study was to review the literature concerning the mandibular canal and inferior alveolar neurovascular bundle anatomical variations related to the implant surgery. Material and Methods Literature was selected through the search of PubMed, Embase and Cochrane electronic databases. The keywords used for search were mandibular canal, inferior alveolar nerve, and inferior alveolar neurovascular bundle. The search was restricted to English language articles, published from 1973 to November 2009. Additionally, a manual search in the major anatomy, dental implant, prosthetic and periodontal journals and books were performed. Results In total, 46 literature sources were obtained and morphological aspects and variations of the anatomy related to implant treatment in posterior mandible were presented as two entities: intraosseous mandibular canal and associated inferior alveolar neurovascular bundle. Conclusions A review of morphological aspects and variations of the anatomy related to mandibular canal and mandibular vital structures are very important especially in implant therapy since inferior alveolar neurovascular bundle exists in different locations and possesses many variations. Individual, gender, age, race, assessing technique used and degree of edentulous alveolar bone atrophy largely influence these variations. It suggests that osteotomies in implant dentistry should not be developed in the posterior mandible until the position of the mandibular canal is established. PMID:24421958

Craniofacial skeletal pattern: is it really correlated with the degree of adenoid obstruction?

PubMed Central

Feres, Murilo Fernando Neuppmann; Muniz, Tomas Salomão; de Andrade, Saulo Henrique; Lemos, Maurilo de Mello; Pignatari, Shirley Shizue Nagata

2015-01-01

OBJECTIVE: The aim of this study was to compare the cephalometric pattern of children with and without adenoid obstruction. METHODS: The sample comprised 100 children aged between four and 14 years old, both males and females, subjected to cephalometric examination for sagittal and vertical skeletal analysis. The sample also underwent nasofiberendoscopic examination intended to objectively assess the degree of adenoid obstruction. RESULTS: The individuals presented tendencies towards vertical craniofacial growth, convex profile and mandibular retrusion. However, there were no differences between obstructive and non-obstructive patients concerning all cephalometric variables. Correlations between skeletal parameters and the percentage of adenoid obstruction were either low or not significant. CONCLUSIONS: Results suggest that specific craniofacial patterns, such as Class II and hyperdivergency, might not be associated with adenoid hypertrophy. PMID:26352848

Geo-Located Tweets. Enhancing Mobility Maps and Capturing Cross-Border Movement.

PubMed

Blanford, Justine I; Huang, Zhuojie; Savelyev, Alexander; MacEachren, Alan M

2015-01-01

Capturing human movement patterns across political borders is difficult and this difficulty highlights the need to investigate alternative data streams. With the advent of smart phones and the ability to attach accurate coordinates to Twitter messages, users leave a geographic digital footprint of their movement when posting tweets. In this study we analyzed 10 months of geo-located tweets for Kenya and were able to capture movement of people at different temporal (daily to periodic) and spatial (local, national to international) scales. We were also able to capture both long and short distances travelled, highlighting regional connections and cross-border movement between Kenya and the surrounding countries. The findings from this study has broad implications for studying movement patterns and mapping inter/intra-region movement dynamics.

Geo-Located Tweets. Enhancing Mobility Maps and Capturing Cross-Border Movement

PubMed Central

Blanford, Justine I.; Huang, Zhuojie; Savelyev, Alexander; MacEachren, Alan M.

2015-01-01

Capturing human movement patterns across political borders is difficult and this difficulty highlights the need to investigate alternative data streams. With the advent of smart phones and the ability to attach accurate coordinates to Twitter messages, users leave a geographic digital footprint of their movement when posting tweets. In this study we analyzed 10 months of geo-located tweets for Kenya and were able to capture movement of people at different temporal (daily to periodic) and spatial (local, national to international) scales. We were also able to capture both long and short distances travelled, highlighting regional connections and cross-border movement between Kenya and the surrounding countries. The findings from this study has broad implications for studying movement patterns and mapping inter/intra-region movement dynamics. PMID:26086772

Spatial and temporal movement dynamics of brook Salvelinus fontinalis and brown trout Salmo trutta

USGS Publications Warehouse

Davis, L.A.; Wagner, Tyler; Barton, Meredith L.

2015-01-01

Native eastern brook trout Salvelinus fontinalis and naturalized brown trout Salmo trutta occur sympatrically in many streams across the brook trout’s native range in the eastern United States. Understanding within- among-species variability in movement, including correlates of movement, has implications for management and conservation. We radio tracked 55 brook trout and 45 brown trout in five streams in a north-central Pennsylvania, USA watershed to quantify the movement of brook trout and brown trout during the fall and early winter to (1) evaluate the late-summer, early winter movement patterns of brook trout and brown trout, (2) determine correlates of movement and if movement patterns varied between brook trout and brown trout, and (3) evaluate genetic diversity of brook trout within and among study streams, and relate findings to telemetry-based observations of movement. Average total movement was greater for brown trout (mean ± SD = 2,924 ± 4,187 m) than for brook trout (mean ± SD = 1,769 ± 2,194 m). Although there was a large amount of among-fish variability in the movement of both species, the majority of movement coincided with the onset of the spawning season, and a threshold effect was detected between stream flow and movement: where movement increased abruptly for both species during positive flow events. Microsatellite analysis of brook trout revealed consistent findings to those found using radio-tracking, indicating a moderate to high degree of gene flow among brook trout populations. Seasonal movement patterns and the potential for relatively large movements of brook and brown trout highlight the importance of considering stream connectivity when restoring and protecting fish populations and their habitats.

Agreement Between Visual Assessment and 2-Dimensional Analysis During Jump Landing Among Healthy Female Athletes.

PubMed

Rabin, Alon; Einstein, Ofira; Kozol, Zvi

2018-04-01

  Altered movement patterns, including increased frontal-plane knee movement and decreased sagittal-plane hip and knee movement, have been associated with several knee disorders. Nevertheless, the ability of clinicians to visually detect such altered movement patterns during high-speed athletic tasks is relatively unknown.   To explore the association between visual assessment and 2-dimensional (2D) analysis of frontal-plane knee movement and sagittal-plane hip and knee movement during a jump-landing task among healthy female athletes.   Cross-sectional study.   Gymnasiums of participating volleyball teams.   A total of 39 healthy female volleyball players (age = 21.0 ± 5.2 years, height = 172.0 ± 8.6 cm, mass = 64.2 ± 7.2 kg) from Divisions I and II of the Israeli Volleyball Association.   Frontal-plane knee movement and sagittal-plane hip and knee movement during jump landing were visually rated as good, moderate, or poor based on previously established criteria. Frontal-plane knee excursion and sagittal-plane hip and knee excursions were measured using free motion-analysis software and compared among athletes with different visual ratings of the corresponding movements.   Participants with different visual ratings of frontal-plane knee movement displayed differences in 2D frontal-plane knee excursion ( P < .01), whereas participants with different visual ratings of sagittal-plane hip and knee movement displayed differences in 2D sagittal-plane hip and knee excursions ( P < .01).   Visual ratings of frontal-plane knee movement and sagittal-plane hip and knee movement were associated with differences in the corresponding 2D hip and knee excursions. Visual rating of these movements may serve as an initial screening tool for detecting altered movement patterns during jump landings.

Management of pediatric mandibular fracture using orthodontic vacuum-formed thermoplastic splint: A case report and review of literature.

PubMed

Sanu, O O; Ayodele, Aos; Akeredolu, M O

2017-05-01

Fractures of the mandible are relatively less frequent in children when compared to adults. The anatomic features of children are protected. Children have a higher adaptation to maxillofacial fractures compared to adults. Treatment principles of mandibular fractures in children differ from that of adults due to concerns regarding mandibular growth and the developing dentition. A case of a 6-year-old boy with fractured mandibular symphysis managed by closed reduction using a vacuum formed thermoplastic splint and circummandibular wiring is presented. This article also provides a review of the literature regarding the management of mandibular fracture in young children.

[Topographological-anatomic changes in the structure of temporo-mandibular joint in case of fracture of the mandible condylar process at cervical level].

PubMed

Volkov, S I; Bazhenov, D V; Semkin, V A

2011-01-01

Pathological changes in soft tissues surrounding the fracture site as well as in the structural elements of temporo-mandibular joint always occured in condylar process fracture with shift at cervical mandibular jaw level. Other changes were also seen in the joint on the opposite normal side. Modelling of condylar process fracture at mandibular cervical level by means of three-dimensional computer model of temporo-mandibular joint contributed to proper understanding of this pathology emergence as well as to prediction and elimination of disorders arising in adjacent to the fracture site tissues.

Mandibular Symmetrical Bilateral Canine-Lateral Incisors Transposition: Its Early Diagnosis and Treatment Considerations.

PubMed

Shapira, Yehoshua; Finkelstein, Tamar; Kadry, Rana; Schonberger, Shirley; Shpack, Nir

2016-01-01

Bilateral mandibular tooth transposition is a relatively rare dental anomaly caused by distal migration of the mandibular lateral incisors and can be detected in the early mixed dentition by radiographic examination. Early diagnosis and interceptive intervention may reduce the risk of possible transposition between the mandibular canine and lateral incisor. This report illustrates the orthodontic management of bilateral mandibular canine-lateral incisor transposition. Correct positioning of the affected teeth was achieved on the left side while teeth on the right side were aligned in their transposed position. It demonstrates the outcome of good alignment of the teeth in the dental arch.

The use of surface monitoring data for the interpretation of landslide movement patterns

NASA Astrophysics Data System (ADS)

Petley, D. N.; Mantovani, F.; Bulmer, M. H.; Zannoni, A.

2005-03-01

The Tessina landslide is a large, seasonally active slope failure located on the southern slopes of Mt. Teverone, in the Alpago valley of NE Italy, consisting of a complex system that has developed in Tertiary Flysch deposits. The landslide, which first became active in 1960, threatens two villages and is hence subject to detailed monitoring, with high quality data being collected using piezometers, inclinometers, extensometers, and through the use of a highly innovative, automated Electronic Distance Measurement (EDM) system, which surveys the location of a large number of reflector targets once every 6 h. These systems form the basis of a warning system that protects the villages, but they also provide a very valuable insight into the patterns of movement of the landslide. In this paper, analysis is presented of the movement of the landslide, concentrating on the EDM dataset, which provides a remarkable record of surface displacement patterns. It is proposed that four distinct movement patterns can be established, which correspond closely to independently defined morphological assessments of the landslide complex. Any given block of material transitions through the four phases of movement as it progresses down the landslide, with the style of movement being controlled primarily by the groundwater conditions. The analysis is augmented with modelling of the landslide, undertaken using the Itasca FLAC code. The modelling suggests that different landslide patterns are observed for different parts of the landslide, primarily as a result of variations in the groundwater conditions. The model suggests that when a movement event occurs, displacements occur initially at the toe of the landslide, then retrogress upslope.

Movement and Orientation Decision Modeling of Rhyzopertha dominica (Coleoptera: Bostrichidae) in the Grain Mass.

PubMed

Cordeiro, Erick M G; Campbell, James F; Phillips, Thomas W

2016-04-01

Grain stored in bins is initially a relatively homogenous resource patch for stored-product insects, but over time, spatial pattern in insect distribution can form, due in part to insect movement patterns. However, the factors that influence stored-product insect movement patterns in grain are not well-understood. This research focused on the movement of the lesser grain borer, Rhyzopertha dominica (F.), within a simulated wheat grain mass (vertical monolayer of wheat) and the identification of factors that contribute to overall and upward movement (age since adult emergence from an infested kernel [1, 7, and 14 d], sex, strain, and different levels of environment quality). We also used the model selection approach to select the most relevant factors and determine the relationships among them. Three-week-old adults tended to stay closer to the surface compared with 1- or 2-wk-old insects. Also, females tended to be more active and to explore a larger area compared with males. Explored area and daily displacement were also significantly strain-dependent, and increasing grain infestation level decreased daily displacement and explored area. Variation in movement pattern is likely to influence the formation of spatial pattern and affect probability to disperse. Understanding movement behavior within a grain bin is crucial to designing better strategies to implement and interpret monitoring programs and to target control tactics. Published by Oxford University Press on behalf of Entomological Society of America 2016. This work is written by US Government employees and is in the public domain in the US.

Movement Patterns, Social Dynamics, and the Evolution of Cooperation

PubMed Central

Smaldino, Paul E.; Schank, Jeffrey C.

2012-01-01

The structure of social interactions influences many aspects of social life, including the spread of information and behavior, and the evolution of social phenotypes. After dispersal, organisms move around throughout their lives, and the patterns of their movement influence their social encounters over the course of their lifespan. Though both space and mobility are known to influence social evolution, there is little analysis of the influence of specific movement patterns on evolutionary dynamics. We explored the effects of random movement strategies on the evolution of cooperation using an agent-based prisoner’s dilemma model with mobile agents. This is the first systematic analysis of a model in which cooperators and defectors can use different random movement strategies, which we chose to fall on a spectrum between highly exploratory and highly restricted in their search tendencies. Because limited dispersal and restrictions to local neighborhood size are known to influence the ability of cooperators to effectively assort, we also assessed the robustness of our findings with respect to dispersal and local capacity constraints. We show that differences in patterns of movement can dramatically influence the likelihood of cooperator success, and that the effects of different movement patterns are sensitive to environmental assumptions about offspring dispersal and local space constraints. Since local interactions implicitly generate dynamic social interaction networks, we also measured the average number of unique and total interactions over a lifetime and considered how these emergent network dynamics helped explain the results. This work extends what is known about mobility and the evolution of cooperation, and also has general implications for social models with randomly moving agents. PMID:22838026

Multi-segmental movement patterns reflect juggling complexity and skill level.

PubMed

Zago, Matteo; Pacifici, Ilaria; Lovecchio, Nicola; Galli, Manuela; Federolf, Peter Andreas; Sforza, Chiarella

2017-08-01

The juggling action of six experts and six intermediates jugglers was recorded with a motion capture system and decomposed into its fundamental components through Principal Component Analysis. The aim was to quantify trends in movement dimensionality, multi-segmental patterns and rhythmicity as a function of proficiency level and task complexity. Dimensionality was quantified in terms of Residual Variance, while the Relative Amplitude was introduced to account for individual differences in movement components. We observed that: experience-related modifications in multi-segmental actions exist, such as the progressive reduction of error-correction movements, especially in complex task condition. The systematic identification of motor patterns sensitive to the acquisition of specific experience could accelerate the learning process. Copyright © 2017 Elsevier B.V. All rights reserved.

The effects of different nickel-titanium instruments on dentinal microcrack formations during root canal preparation.

PubMed

Ustun, Yakup; Aslan, Tugrul; Sagsen, Burak; Kesim, Bertan

2015-01-01

The aim of the present study was to investigate the incidence of dentinal microcracks caused by different preparation techniques. 120 extracted human mandibular incisor teeth were divided into five experimental groups and one control group (n = 20): Group 1: Hand preparation with balanced force technique up to #25 K-file. Group 2: Preparation with only ProTaper F2 instrument in a reciprocating movement. Group 3: Preparation with Reciproc R25 instrument in a reciprocating movement. Group 4: Preparation with ProTaper instruments up to F2 instrument. Group 5: Preparation with ProTaper Next instruments up to X2 instrument. No procedure was applied to control group. The roots were sectioned horizontally at 3, 6 and 9 mm from the apex and examined. Absence or presence of dentinal microcracks was noted. The Chi-square test was performed to compare the appearance of cracked roots between all groups. There were no significant differences among the groups (P > 0.05). In conclusion, except the hand file and control group, all experimental groups showed microcrack formations.

Prosthodontic Rehabilitation of Patients with Bell's Palsy: Our Experience.

PubMed

Rajapur, Anand; Mitra, Nirban; Prakash, V Jeevan; Rah, Sajad Ahmad; Thumar, Sagar

2015-01-01

Bell's palsy is an idiopathic unilateral lower motor neuron paresis or paralysis of the facial nerve of sudden onset. It involves loss of muscular control on the affected side of the face. This paper reports the prosthodontic management of patients with Bell's palsy and also describes a technique to stabilize the jaw movements in complete denture patients using interim dentures. A 65-year-old male edentulous patient and a 55-year-old female edentulous patient reported to the department of prosthodontics to get their missing teeth replaced. They both gave history of facial paralysis and were diagnosed for Bell's palsy. Interim training dentures with flat occlusal tables were fabricated first to correct and stabilize their mandibular movements. During initial 4 weeks, there was poor functioning of the interim dentures. Gradually by 8(th) week the patients started stabilizing the interim dentures and were functional. After observing the improvement when the patients had no pain and could stabilize and use the treatment dentures successfully, definitive complete dentures were fabricated. This case report presents a systematic approach to successively rehabilitate edentulous patients with Bell's palsy.

Prosthodontic Rehabilitation of Patients with Bell’s Palsy: Our Experience

PubMed Central

Rajapur, Anand; Mitra, Nirban; Prakash, V Jeevan; Rah, Sajad Ahmad; Thumar, Sagar

2015-01-01

Bell’s palsy is an idiopathic unilateral lower motor neuron paresis or paralysis of the facial nerve of sudden onset. It involves loss of muscular control on the affected side of the face. This paper reports the prosthodontic management of patients with Bell’s palsy and also describes a technique to stabilize the jaw movements in complete denture patients using interim dentures. A 65-year-old male edentulous patient and a 55-year-old female edentulous patient reported to the department of prosthodontics to get their missing teeth replaced. They both gave history of facial paralysis and were diagnosed for Bell’s palsy. Interim training dentures with flat occlusal tables were fabricated first to correct and stabilize their mandibular movements. During initial 4 weeks, there was poor functioning of the interim dentures. Gradually by 8th week the patients started stabilizing the interim dentures and were functional. After observing the improvement when the patients had no pain and could stabilize and use the treatment dentures successfully, definitive complete dentures were fabricated. This case report presents a systematic approach to successively rehabilitate edentulous patients with Bell’s palsy. PMID:26668488

Laban Movement Analysis towards Behavior Patterns

NASA Astrophysics Data System (ADS)

Santos, Luís; Dias, Jorge

This work presents a study about the use of Laban Movement Analysis (LMA) as a robust tool to describe human basic behavior patterns, to be applied in human-machine interaction. LMA is a language used to describe and annotate dancing movements and is divided in components [1]: Body, Space, Shape and Effort. Despite its general framework is widely used in physical and mental therapy [2], it has found little application in the engineering domain. Rett J. [3] proposed to implement LMA using Bayesian Networks. However LMA component models have not yet been fully implemented. A study on how to approach behavior using LMA is presented. Behavior is a complex feature and movement chain, but we believe that most basic behavior primitives can be discretized in simple features. Correctly identifying Laban parameters and the movements the authors feel that good patterns can be found within a specific set of basic behavior semantics.

Masticatory form and function in the African apes.

PubMed

Taylor, Andrea B

2002-02-01

This study examines variability in masticatory morphology as a function of dietary preference among the African apes. The African apes differ in the degree to which they consume leaves and other fibrous vegetation. Gorilla gorilla beringei, the eastern mountain gorilla, consumes the most restricted diet comprised of mechanically resistant foods such as leaves, pith, bark, and bamboo. Gorilla gorilla gorilla, the western lowland gorilla subspecies, consumes leaves and other terrestrial herbaceous vegetation (THV) but also consumes a fair amount of ripe, fleshy fruit. In contrast to gorillas, chimpanzees are frugivores and rely on vegetation primarily as fallback foods. However, there has been a long-standing debate regarding whether Pan paniscus, the pygmy chimpanzee (or bonobo), consumes greater quantities of THV as compared to Pan troglodytes, the common chimpanzee. Because consumption of resistant foods involves more daily chewing cycles and may require larger average bite force, the mechanical demands placed on the masticatory system are expected to be greater in folivores as compared to primates that consume large quantities of fleshy fruit. Therefore, more folivorous taxa are predicted to exhibit features that improve load-resistance capabilities and increase force production. To test this hypothesis, jaw and skull dimensions were compared in ontogenetic series of G. g. beringei, G. g. gorilla, P. t. troglodytes, and P. paniscus. Controlling for the influence of allometry, results show that compared to both chimpanzees and bonobos, gorillas exhibit some features of the jaw complex that are suggestive of improved masticatory efficiency. For example, compared to all other taxa, G. g. beringei has a significantly wider mandibular corpus and symphysis, larger area for the masseter muscle, higher mandibular ramus, and higher mandibular condyle relative to the occlusal plane of the mandible. However, the significantly wider mandibular symphysis may be an architectural response to increasing symphyseal curvature with interspecific increase in size. Moreover, Gorilla and Pan do not vary consistently in all features, and some differences run counter to predictions based on dietary variation. Thus, the morphological responses are not entirely consonant with predictions based on hypothesized loading regimes. Finally, despite morphological differences between bonobos and chimpanzees, there is no systematic pattern of differentiation that can be clearly linked to differences in diet. Results indicate that while some features may be linked to differences in diet among the African apes, diet alone cannot account for the patterns of morphological variation demonstrated in this study. Allometric constraints and dental development also appear to play a role in morphological differentiation among the African apes. Copyright 2002 Wiley-Liss, Inc.

Bilateral mandibular angle fractures: clinical considerations.

PubMed

Boffano, Paolo; Roccia, Fabio

2010-03-01

The mandibular angle is a frequent site of fracture. It is a weak zone that is more exposed to fractures than other areas of the mandibular bone. The presence of incompletely erupted third molars is associated with a further increased risk of angle fractures. Our objective was to evaluate and discuss the surgical outcomes of a group of patients with bilateral mandibular angle fractures.In our study, patients with bilateral mandibular angle fractures surgically treated from January 1, 2001, to June 30, 2009, at the Division of Maxillofacial Surgery of the University of Turin were retrospectively analyzed. A combined transbuccal and intraoral approach or an intraoral approach only was adopted.Eight patients (7 men and 1 woman) underwent surgery for bilateral mandibular angle fractures. Good to satisfactory reduction of the fractures was obtained with both surgical techniques. Good to fair restored occlusion was observed postoperatively in all patients.Successful treatment of bilateral mandibular angle fractures may be achieved via different techniques. Superficially impacted third molars seem to be associated with an increased risk of angle fractures. Bilateral angle fractures are an ideal model to study the biomechanical pathogenesis of angle fractures.

Chincup treatment modifies the mandibular shape in children with prognathism.

PubMed

Alarcón, José Antonio; Bastir, Markus; Rosas, Antonio; Molero, Julia

2011-07-01

Although chincups are the preferred treatment for growing children with mandibular prognathism, the mechanism by which chincups improve this condition remains unclear. The aim of this study was to use geometric morphometrics to evaluate changes in the shape of the mandible of prognathic children treated with a chincup. Geometric morphometrics were used to evaluate the short-term mandibular shape changes in 50 prognathic children treated with chincups compared with 40 untreated matched controls. Twenty-one 2-dimensional mandibular landmarks from cephalograms taken before and after 36 months of treatment or observation were analyzed by Procrustes superimposition and thin plate spline. Permutation tests of the treated patients showed highly significant differences in the mandibular shapes before and after treatment, and compared with the control group after the observation period. The thin plate spline grid deformations indicated more rectangular mandibular configuration, forward condyle orientation, condyle neck compression, gonial area compression, and symphysis narrowing. Early chincup treatment widely modifies the mandibular shape of prognathic children to improve Class III malocclusion. Copyright © 2011 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

24 CFR 570.456 - Ineligible activities and limitations on eligible activities.

Code of Federal Regulations, 2011 CFR

2011-04-01

... relocation of a plant or facility from one area to another, if it is demonstrated to HUD's satisfaction that... has been a significant current pattern of movement, to areas reasonably proximate, of jobs of the... significant pattern of job movement and the likelihood of continuation of such a pattern has been from a...

Construction of a cDNA library for miniature pig mandibular deciduous molars

PubMed Central

2014-01-01

Background The miniature pig provides an excellent experimental model for tooth morphogenesis because its diphyodont and heterodont dentition resembles that of humans. However, little information is available on the process of tooth development or the exact molecular mechanisms controlling tooth development in miniature pigs or humans. Thus, the analysis of gene expression related to each stage of tooth development is very important. Results In our study, after serial sections were made, the development of the crown of the miniature pigs’ mandibular deciduous molar could be divided into five main phases: dental lamina stage (E33-E35), bud stage (E35-E40), cap stage (E40-E50), early bell stage (E50-E60), and late bell stage (E60-E65). Total RNA was isolated from the tooth germ of miniature pig embryos at E35, E45, E50, and E60, and a cDNA library was constructed. Then, we identified cDNA sequences on a large scale screen for cDNA profiles in the developing mandibular deciduous molars (E35, E45, E50, and E60) of miniature pigs using Illumina Solexa deep sequencing. Microarray assay was used to detect the expression of genes. Lastly, through Unigene sequence analysis and cDNA expression pattern analysis at E45 and E60, we found that 12 up-regulated and 15 down-regulated genes during the four periods are highly conserved genes homologous with known Homo sapiens genes. Furthermore, there were 6 down-regulated and 2 up-regulated genes in the miniature pig that were highly homologous to Homo sapiens genes compared with those in the mouse. Conclusion Our results not only identify the specific transcriptome and cDNA profile in developing mandibular deciduous molars of the miniature pig, but also provide useful information for investigating the molecular mechanism of tooth development in the miniature pig. PMID:24750690

Inter-rater reliability for movement pattern analysis (MPA): measuring patterning of behaviors versus discrete behavior counts as indicators of decision-making style

PubMed Central

Connors, Brenda L.; Rende, Richard; Colton, Timothy J.

2014-01-01

The unique yield of collecting observational data on human movement has received increasing attention in a number of domains, including the study of decision-making style. As such, interest has grown in the nuances of core methodological issues, including the best ways of assessing inter-rater reliability. In this paper we focus on one key topic – the distinction between establishing reliability for the patterning of behaviors as opposed to the computation of raw counts – and suggest that reliability for each be compared empirically rather than determined a priori. We illustrate by assessing inter-rater reliability for key outcome measures derived from movement pattern analysis (MPA), an observational methodology that records body movements as indicators of decision-making style with demonstrated predictive validity. While reliability ranged from moderate to good for raw counts of behaviors reflecting each of two Overall Factors generated within MPA (Assertion and Perspective), inter-rater reliability for patterning (proportional indicators of each factor) was significantly higher and excellent (ICC = 0.89). Furthermore, patterning, as compared to raw counts, provided better prediction of observable decision-making process assessed in the laboratory. These analyses support the utility of using an empirical approach to inform the consideration of measuring patterning versus discrete behavioral counts of behaviors when determining inter-rater reliability of observable behavior. They also speak to the substantial reliability that may be achieved via application of theoretically grounded observational systems such as MPA that reveal thinking and action motivations via visible movement patterns. PMID:24999336