Carbon Emission Reduction with Capital Constraint under Greening Financing and Cost Sharing Contract.

PubMed

Qin, Juanjuan; Zhao, Yuhui; Xia, Liangjie

2018-04-13

Motivated by the industrial practices, this work explores the carbon emission reductions for the manufacturer, while taking into account the capital constraint and the cap-and-trade regulation. To alleviate the capital constraint, two contracts are analyzed: greening financing and cost sharing. We use the Stackelberg game to model four cases as follows: (1) in Case A1, the manufacturer has no greening financing and no cost sharing; (2) in Case A2, the manufacturer has greening financing, but no cost sharing; (3) in Case B1, the manufacturer has no greening financing but has cost sharing; and, (4) in Case B2, the manufacturer has greening financing and cost sharing. Then, using the backward induction method, we derive and compare the equilibrium decisions and profits of the participants in the four cases. We find that the interest rate of green finance does not always negatively affect the carbon emission reduction of the manufacturer. Meanwhile, the cost sharing from the retailer does not always positively affect the carbon emission reduction of the manufacturer. When the cost sharing is low, both of the participants' profits in Case B1 (under no greening finance) are not less than that in Case B2 (under greening finance). When the cost sharing is high, both of the participants' profits in Case B1 (under no greening finance) are less than that in Case B2 (under greening finance).

Evolution of design considerations in complex craniofacial reconstruction using patient-specific implants.

PubMed

Peel, Sean; Bhatia, Satyajeet; Eggbeer, Dominic; Morris, Daniel S; Hayhurst, Caroline

2017-06-01

Previously published evidence has established major clinical benefits from using computer-aided design, computer-aided manufacturing, and additive manufacturing to produce patient-specific devices. These include cutting guides, drilling guides, positioning guides, and implants. However, custom devices produced using these methods are still not in routine use, particularly by the UK National Health Service. Oft-cited reasons for this slow uptake include the following: a higher up-front cost than conventionally fabricated devices, material-choice uncertainty, and a lack of long-term follow-up due to their relatively recent introduction. This article identifies a further gap in current knowledge - that of design rules, or key specification considerations for complex computer-aided design/computer-aided manufacturing/additive manufacturing devices. This research begins to address the gap by combining a detailed review of the literature with first-hand experience of interdisciplinary collaboration on five craniofacial patient case studies. In each patient case, bony lesions in the orbito-temporal region were segmented, excised, and reconstructed in the virtual environment. Three cases translated these digital plans into theatre via polymer surgical guides. Four cases utilised additive manufacturing to fabricate titanium implants. One implant was machined from polyether ether ketone. From the literature, articles with relevant abstracts were analysed to extract design considerations. In all, 19 frequently recurring design considerations were extracted from previous publications. Nine new design considerations were extracted from the case studies - on the basis of subjective clinical evaluation. These were synthesised to produce a design considerations framework to assist clinicians with prescribing and design engineers with modelling. Promising avenues for further research are proposed.

Identified research directions for using manufacturing knowledge earlier in the product lifecycle

PubMed Central

Hedberg, Thomas D.; Hartman, Nathan W.; Rosche, Phil; Fischer, Kevin

2016-01-01

Design for Manufacturing (DFM), especially the use of manufacturing knowledge to support design decisions, has received attention in the academic domain. However, industry practice has not been studied enough to provide solutions that are mature for industry. The current state of the art for DFM is often rule-based functionality within Computer-Aided Design (CAD) systems that enforce specific design requirements. That rule-based functionality may or may not dynamically affect geometry definition. And, if rule-based functionality exists in the CAD system, it is typically a customization on a case-by-case basis. Manufacturing knowledge is a phrase with vast meanings, which may include knowledge on the effects of material properties decisions, machine and process capabilities, or understanding the unintended consequences of design decisions on manufacturing. One of the DFM questions to answer is how can manufacturing knowledge, depending on its definition, be used earlier in the product lifecycle to enable a more collaborative development environment? This paper will discuss the results of a workshop on manufacturing knowledge that highlights several research questions needing more study. This paper proposes recommendations for investigating the relationship of manufacturing knowledge with shape, behavior, and context characteristics of product to produce a better understanding of what knowledge is most important. In addition, the proposal includes recommendations for investigating the system-level barriers to reusing manufacturing knowledge and how model-based manufacturing may ease the burden of knowledge sharing. Lastly, the proposal addresses the direction of future research for holistic solutions of using manufacturing knowledge earlier in the product lifecycle. PMID:27990027

Identified research directions for using manufacturing knowledge earlier in the product lifecycle.

PubMed

Hedberg, Thomas D; Hartman, Nathan W; Rosche, Phil; Fischer, Kevin

2017-01-01

Design for Manufacturing (DFM), especially the use of manufacturing knowledge to support design decisions, has received attention in the academic domain. However, industry practice has not been studied enough to provide solutions that are mature for industry. The current state of the art for DFM is often rule-based functionality within Computer-Aided Design (CAD) systems that enforce specific design requirements. That rule-based functionality may or may not dynamically affect geometry definition. And, if rule-based functionality exists in the CAD system, it is typically a customization on a case-by-case basis. Manufacturing knowledge is a phrase with vast meanings, which may include knowledge on the effects of material properties decisions, machine and process capabilities, or understanding the unintended consequences of design decisions on manufacturing. One of the DFM questions to answer is how can manufacturing knowledge, depending on its definition, be used earlier in the product lifecycle to enable a more collaborative development environment? This paper will discuss the results of a workshop on manufacturing knowledge that highlights several research questions needing more study. This paper proposes recommendations for investigating the relationship of manufacturing knowledge with shape, behavior, and context characteristics of product to produce a better understanding of what knowledge is most important. In addition, the proposal includes recommendations for investigating the system-level barriers to reusing manufacturing knowledge and how model-based manufacturing may ease the burden of knowledge sharing. Lastly, the proposal addresses the direction of future research for holistic solutions of using manufacturing knowledge earlier in the product lifecycle.

CIMOSA process classification for business process mapping in non-manufacturing firms: A case study

NASA Astrophysics Data System (ADS)

Latiffianti, Effi; Siswanto, Nurhadi; Wiratno, Stefanus Eko; Saputra, Yudha Andrian

2017-11-01

A business process mapping is one important means to enable an enterprise to effectively manage the value chain. One of widely used approaches to classify business process for mapping purpose is Computer Integrated Manufacturing System Open Architecture (CIMOSA). CIMOSA was initially designed for Computer Integrated Manufacturing (CIM) system based enterprises. This paper aims to analyze the use of CIMOSA process classification for business process mapping in the firms that do not fall within the area of CIM. Three firms of different business area that have used CIMOSA process classification were observed: an airline firm, a marketing and trading firm for oil and gas products, and an industrial estate management firm. The result of the research has shown that CIMOSA can be used in non-manufacturing firms with some adjustment. The adjustment includes addition, reduction, or modification of some processes suggested by CIMOSA process classification as evidenced by the case studies.

Investigation of an outbreak of hypersensitivity-type reactions during the 2004 national measles-mumps-rubella vaccination campaign in Brazil.

PubMed

Freitas, Daniel R C; Moura, Evoide; Araújo, Gisele; Cardoso, Alessandra; Scheidt, Penelope; Ferraz, Elizabete; Madalosso, Geraldine; Chen, Robert T; Hatch, Douglas L

2013-01-30

During Brazil's national measles, mumps, and rubella (MMR) vaccination campaign in August 2004, an unexpectedly high rate of hypersensitivity-type adverse events (HAEs) was reported. We reviewed information about children with suspected HAEs reported by clinicians to Brazil's national passive surveillance system for adverse events following immunization (AEFI), compared attack rate of HAE by manufacturer of MMR vaccine used in the campaign, and conducted a case-control study to determine possible risk factors for HAEs. During the 2004 national campaign, the rate of HAEs following MMR vaccination was one log higher for manufacturer A (15.2/100,000 doses administered) compared to the other two manufacturers (1.2 and 0.6/100,000 doses; p<0.0001); a similar pattern was observed retrospectively in analysis of the 2000-2003 AEFI surveillance (0.95 vs. 0.07 per 100,000 doses administered; p<0.0001). In the case-control study, among the 49 case-patients with HAEs identified, reported symptoms included conjunctival injection (60%), urticaria (55%), fever (54%), and facial edema (53%); no deaths occurred. The median time interval between vaccination and symptom onset was 42min (range: 5min-24h). We did not identify any differences in the proportion of case-patients and control children with a history of known allergy to food (including egg, egg-containing products or gelatin), drugs, or environmental antigens. Our study highlights the importance of a well-functioning routine AEFI surveillance system linked with mass vaccination campaigns. Such a system in Brazil permitted timely detection of HAEs and validation of a safety signal associated with one vaccine manufacturer. Unlike earlier publications, this outbreak linked to a single manufacturer of MMR showed no association with a prior allergic history to eggs or other foods, including gelatin; subsequent studies implicate the dextran stabilizer in MMR from manufacturer A as the likely cause of HAEs. Copyright © 2012 Elsevier Ltd. All rights reserved.

Case Studies in Modelling, Control in Food Processes.

PubMed

Glassey, J; Barone, A; Montague, G A; Sabou, V

This chapter discusses the importance of modelling and control in increasing food process efficiency and ensuring product quality. Various approaches to both modelling and control in food processing are set in the context of the specific challenges in this industrial sector and latest developments in each area are discussed. Three industrial case studies are used to demonstrate the benefits of advanced measurement, modelling and control in food processes. The first case study illustrates the use of knowledge elicitation from expert operators in the process for the manufacture of potato chips (French fries) and the consequent improvements in process control to increase the consistency of the resulting product. The second case study highlights the economic benefits of tighter control of an important process parameter, moisture content, in potato crisp (chips) manufacture. The final case study describes the use of NIR spectroscopy in ensuring effective mixing of dry multicomponent mixtures and pastes. Practical implementation tips and infrastructure requirements are also discussed.

Identifying Effective Pedagogical Approaches for Online Workplace Training: A Case Study of the South African Wood Products Manufacturing Sector

ERIC Educational Resources Information Center

Macdonald, Ian S.; Bullen, Mark; Kozak, R. A.

2007-01-01

This study investigated appropriate pedagogical techniques for workplace e-learning programs in the South African wood products (furniture) manufacturing sector. The study found that learners responded favourably to constructivist teaching approaches, such as asynchronous discussions, open-ended task-based activities, and assignments incorporating…

27 CFR 53.182 - Supporting evidence required in case of tax-paid articles used for further manufacture.

Code of Federal Regulations, 2010 CFR

2010-04-01

... required in case of tax-paid articles used for further manufacture. 53.182 Section 53.182 Alcohol, Tobacco... articles used for further manufacture. (a) Evidence to be submitted by claimant. No claim for credit or... material in the manufacture or production of, or as a component part of, a second article manufactured or...

Occupational Asthma in Antibiotic Manufacturing Workers: Case Reports and Systematic Review

PubMed Central

Díaz Angulo, Sara; Szram, Joanna; Welch, Jenny; Cannon, Julie; Cullinan, Paul

2011-01-01

Background. The risks of occupational asthma (OA) from antibiotics are uncertain. We report 4 new cases and a systematic review of the literature. Methods. Cases were identified through a specialist clinic, each underwent specific provocation testing (SPT). We subsequently reviewed the published literature. Results. The patients were employed in the manufacture of antibiotics; penicillins were implicated in three cases, in the fourth erythromycin, not previously reported to cause OA. In two, there was evidence of specific IgE sensitisation. At SPT each developed a late asthmatic reaction and increased bronchial hyperresponsiveness. 36 case reports have been previously published, 26 (citing penicillins or cephalosporins). Seven cross-sectional workplace-based surveys found prevalences of 5–8%. Conclusions. OA in antibiotic manufacturers may be more common than is generally recognised. Its pathogenesis remains unclear; immunological tests are of uncertain value and potential cases require confirmation with SPT. Further study of its frequency, mechanisms, and diagnosis is required. PMID:21603168

The make or buy debate: considering the limitations of domestic production in Tanzania.

PubMed

Wilson, Kinsley Rose; Kohler, Jillian Clare; Ovtcharenko, Natalia

2012-06-29

In order to ensure their population's regular access to essential medicines, many least developed countries and developing countries are faced with the policy question of whether to import or manufacture drugs locally, in particular for life-saving antiretroviral medicines for HIV/AIDS patients. In order for domestic manufacturing to be viable and cost-effective, the local industry must be able to compete with international suppliers of medicines by producing sufficiently low cost ARVs. This paper considers the 'make-or-buy' dilemma by using Tanzania as a case study. Key informant interviews, event-driven observation, and purposive sampling of documents were used to evaluate the case study. The case study focused on Tanzania's imitation technology transfer agreement to locally manufacture a first-line ARV (3TC + d4T + NVP), reverse engineering the ARV. Tanzania is limited by weak political support for the use of TRIPS flexibilities, limited production capacity for ARVs and limited competitiveness in both domestic and regional markets. The Ministry of Health and Social Welfare encourages the use of flexibilities while others push for increased IP protection. Insufficient production capacity and lack of access to donor-financed tenders make it difficult to obtain economies of scale and provide competitive prices. Within the "make-or-buy" context, it was determined that there are significant limitations in domestic manufacturing for developing countries. The case study highlights the difficulty of governments to make use of economies of scale and produce low-cost medicines, attract technology transfer, and utilize the flexibilities of the WTO Agreement on Trade-Related Aspects of Intellectual Property Rights (TRIPS). The results demonstrate the importance of evaluating barriers to the use of TRIPS flexibilities and long-term planning across sectors in future technology transfer and manufacturing initiatives.

Carbon Emission Reduction with Capital Constraint under Greening Financing and Cost Sharing Contract

PubMed Central

Qin, Juanjuan; Zhao, Yuhui; Xia, Liangjie

2018-01-01

Motivated by the industrial practices, this work explores the carbon emission reductions for the manufacturer, while taking into account the capital constraint and the cap-and-trade regulation. To alleviate the capital constraint, two contracts are analyzed: greening financing and cost sharing. We use the Stackelberg game to model four cases as follows: (1) in Case A1, the manufacturer has no greening financing and no cost sharing; (2) in Case A2, the manufacturer has greening financing, but no cost sharing; (3) in Case B1, the manufacturer has no greening financing but has cost sharing; and, (4) in Case B2, the manufacturer has greening financing and cost sharing. Then, using the backward induction method, we derive and compare the equilibrium decisions and profits of the participants in the four cases. We find that the interest rate of green finance does not always negatively affect the carbon emission reduction of the manufacturer. Meanwhile, the cost sharing from the retailer does not always positively affect the carbon emission reduction of the manufacturer. When the cost sharing is low, both of the participants’ profits in Case B1 (under no greening finance) are not less than that in Case B2 (under greening finance). When the cost sharing is high, both of the participants’ profits in Case B1 (under no greening finance) are less than that in Case B2 (under greening finance). PMID:29652859

Technology Solutions Case Study: Southern Energy Homes, First DOE Zero Energy Ready Manufactured Home

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

The country’s first Zero Energy Ready manufactured home that is certified by the U.S. Department of Energy (DOE) is up and running in Russellville, Alabama. The manufactured home was built by a partnership between Southern Energy Homes and the Advanced Residential Integrated Energy Solutions Collaborative (ARIES), which is a DOE Building America team. The effort was part of a three-home study including a standard-code manufactured home and an ENERGY STAR® manufactured home. Cooling-season results showed that the building used half the space-conditioning energy of a manufactured home built to the U.S. Department of Housing and Urban Development’s (HUD’s) Manufactured Homemore » Construction and Safety Standards. These standards are known collectively as the HUD Code, which is the building standard for all U.S. manufactured housing.« less

Market surveillance of in vitro diagnostics by the BfArM until end 2010: how safe are products for tumor diagnostics?

PubMed

Siekmeier, R; Wetzel, D

2013-01-01

The European Directive 98/79/EC on in vitro diagnostic medical devices (IVD) regulates the marketing and post market surveillance of IVD in the European Economic Area. In cases of incidents and field corrective actions the manufacturers have to inform the responsible Competent Authorities (CA). In Germany, the Federal Institute for Drugs and Medical Devices (BfArM) is the responsible CA for most IVD. In this study all notifications regarding IVD (tests, calibrators, kits, and control materials, except laboratory analyzers) for tumor diagnostics received by the BfArM between begin 1999 until end of 2010 were analyzed. All notifications were analyzed in respect to the type of product, the source of notification, the underlying product defects and the corrective actions performed. In the observation period, a total of 2,851 notifications were received of which 84 were related to IVD for tumor diagnostics included in this study (clinical chemistry - 63, histology - 6, molecular biology - 3, rapid tests - 12). Reports were received from manufacturers (68 cases), CA (8 cases), users (4 cases) and other sources (4 cases). In the group of IVD based on clinical chemistry means, the affected products were mostly those for the measurement of prostate specific antigen (PSA, 14 cases), human chorion gonadotropine (13 cases), carcino embryonic antigen (6 cases), CA 19-9 (6 cases), α(1)-fetoprotein (6 cases) and CA 125 (5 cases), whereas in test strips 9 out of the 12 notifications were related to PSA. Investigations of the manufacturers were able to identify the underlying root causes of product failures in 66 cases (78.6%). In 10 cases (11.9%) the root cause remained unclear and in 6 cases and 2 cases (7.1% and 2.4%) a product failure was excluded or a user error was the underlying cause. Most common root causes of product failures were material defects (24 cases) and manufacturing errors (15 cases). Corrective actions were performed by the manufacturers in 64 cases (76.2%) and were predominantly (multiple entries possible) customer information (62 cases, mandatory in case of a recall), recalls (45 cases), modifications in production or quality management (45 cases) and design changes (14 cases). The obtained results suggest that the system for post marketing surveillance of IVD is an established tool to enhance product safety and provides valuable information on product specific problems serving for improvement of product safety.

Ownership reform and the changing manufacturing landscape in Chinese cities: The case of Wuxi.

PubMed

Zhou, Lei; Yang, Shan; Wang, Shuguang; Xiong, Liyang

2017-01-01

Since the economic transition, manufacturing in China has undergone profound changes not only in number of enterprises, but also in ownership structure and intra-urban spatial distribution. Investigating the changing manufacturing landscape from the perspective of ownership structure is critical to a deep understanding of the changing role of market and government in re-shaping manufacturing location behavior. Through a case study of Wuxi, a city experiencing comprehensive ownership reform, this paper presents a detailed analysis of the intra-urban spatial shift of manufacturing, identifies the location discrepancies, and examines the underlying forces responsible for the geographical differentiations. Through zone- and district-based analysis, a distinctive trend of decentralization and suburbanization, as well as an uneven distribution of manufacturing, is unveiled. The results of Location Quotient analysis show that the distribution of manufacturing by ownership exhibits distinctive spatial patterns, which is characterized by a historically-based, market-led, and institutionally-created spatial variation. By employing Hot Spot analysis, the role of development zones in attracting manufacturing enterprises of different ownerships is established. Overall, the location behavior of the diversified manufacturing has been increasingly based on the forces of market since the land marketization began. A proactive role played by local governments has also guided the enterprise location decision through spatial planning and regulatory policies.

Ownership reform and the changing manufacturing landscape in Chinese cities: The case of Wuxi

PubMed Central

Zhou, Lei; Yang, Shan; Wang, Shuguang

2017-01-01

Since the economic transition, manufacturing in China has undergone profound changes not only in number of enterprises, but also in ownership structure and intra-urban spatial distribution. Investigating the changing manufacturing landscape from the perspective of ownership structure is critical to a deep understanding of the changing role of market and government in re-shaping manufacturing location behavior. Through a case study of Wuxi, a city experiencing comprehensive ownership reform, this paper presents a detailed analysis of the intra-urban spatial shift of manufacturing, identifies the location discrepancies, and examines the underlying forces responsible for the geographical differentiations. Through zone- and district-based analysis, a distinctive trend of decentralization and suburbanization, as well as an uneven distribution of manufacturing, is unveiled. The results of Location Quotient analysis show that the distribution of manufacturing by ownership exhibits distinctive spatial patterns, which is characterized by a historically-based, market-led, and institutionally-created spatial variation. By employing Hot Spot analysis, the role of development zones in attracting manufacturing enterprises of different ownerships is established. Overall, the location behavior of the diversified manufacturing has been increasingly based on the forces of market since the land marketization began. A proactive role played by local governments has also guided the enterprise location decision through spatial planning and regulatory policies. PMID:28278284

Effect of a chemical manufacturing plant on community cancer rates

PubMed Central

Mannes, Trish; Emmett, Katy; Willmore, Alan; Churches, Tim; Sheppeard, Vicky; Kaldor, Jill

2005-01-01

Background We conducted a retrospective study to determine if potential past exposure to dioxin had resulted in increased incidence of cancer in people living near a former manufacturing plant in New South Wales, Australia. During operation, from 1928 to 1970, by-products of the manufacturing process, including dioxin and other chemical waste, were dumped into wetlands and mangroves, discharged into a nearby bay and used to reclaim land along the foreshore, leaving a legacy of significant dioxin contamination. Methods We selected 20 Census Collector Districts within 1.5 kilometres of the former manufacturing plant as the study area. We obtained data on all cases of cancer and deaths from cancer in New South Wales from 1972 to 2001. We also compared rates for some cancer types that have been associated with dioxin exposure. Based on a person's residential address at time of cancer diagnosis, or at time of death due to cancer, various geo-coding software and processes were used to determine which collector district the case or death should be attributed to. Age and sex specific population data were used to calculate standardised incidence ratios and standardised mortality ratios, to compare the study area to two comparison areas, using indirect standardisation. Results During the 30-year study period 1,106 cases of cancer and 524 deaths due to cancer were identified in the study area. This corresponds to an age-sex standardised rate of 3.2 cases per 1,000 person-years exposed and 1.6 deaths per 1,000 person-years exposed. The study area had a lower rate of cancer and deaths from cancer than the comparison areas. The case incidence and mortality due to lung and bronchus carcinomas and haematopoietic cancers did not differ significantly from the comparison areas for the study period. There was no obvious geographical trend in ratios when comparing individual collector districts to New South Wales according to distance from the potential source of dioxin exposure. Conclusion This investigation found no evidence that dioxin contamination from this site resulted in increased cancer rates in the potentially exposed population living around the former manufacturing plant. PMID:15811184

Effect of a chemical manufacturing plant on community cancer rates.

PubMed

Mannes, Trish; Emmett, Katy; Willmore, Alan; Churches, Tim; Sheppeard, Vicky; Kaldor, Jill

2005-04-05

We conducted a retrospective study to determine if potential past exposure to dioxin had resulted in increased incidence of cancer in people living near a former manufacturing plant in New South Wales, Australia. During operation, from 1928 to 1970, by-products of the manufacturing process, including dioxin and other chemical waste, were dumped into wetlands and mangroves, discharged into a nearby bay and used to reclaim land along the foreshore, leaving a legacy of significant dioxin contamination. We selected 20 Census Collector Districts within 1.5 kilometres of the former manufacturing plant as the study area. We obtained data on all cases of cancer and deaths from cancer in New South Wales from 1972 to 2001. We also compared rates for some cancer types that have been associated with dioxin exposure. Based on a person's residential address at time of cancer diagnosis, or at time of death due to cancer, various geo-coding software and processes were used to determine which collector district the case or death should be attributed to. Age and sex specific population data were used to calculate standardised incidence ratios and standardised mortality ratios, to compare the study area to two comparison areas, using indirect standardisation. During the 30-year study period 1,106 cases of cancer and 524 deaths due to cancer were identified in the study area. This corresponds to an age-sex standardised rate of 3.2 cases per 1,000 person-years exposed and 1.6 deaths per 1,000 person-years exposed. The study area had a lower rate of cancer and deaths from cancer than the comparison areas. The case incidence and mortality due to lung and bronchus carcinomas and haematopoietic cancers did not differ significantly from the comparison areas for the study period. There was no obvious geographical trend in ratios when comparing individual collector districts to New South Wales according to distance from the potential source of dioxin exposure. This investigation found no evidence that dioxin contamination from this site resulted in increased cancer rates in the potentially exposed population living around the former manufacturing plant.

Global Value Chain and Manufacturing Analysis on Geothermal Power Plant Turbines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akar, Sertac; Augustine, Chad; Kurup, Parthiv

In this study, we have undertaken a robust analysis of the global supply chain and manufacturing costs for components of Organic Rankine Cycle (ORC) Turboexpander and steam turbines used in geothermal power plants. We collected a range of market data influencing manufacturing from various data sources and determined the main international manufacturers in the industry. The data includes the manufacturing cost model to identify requirements for equipment, facilities, raw materials, and labor. We analyzed three different cases; 1) 1 MW geothermal ORC Turboexpander 2) 5 MW ORC Turboexpander 3) 20 MW geothermal Steam Turbine

Corporate Energy Conservation Program for Alcoa North American Extrusions: Office of Industrial Technologies (OIT) Aluminum BestPractices Management Case Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

U.S. Department of Energy

2001-08-06

This case study is the latest in a series on industrial firms who are implementing energy efficient technologies and system improvements into their manufacturing processes. The case studies document the activities, savings, and lessons learned on these projects.

Decision-support tool for assessing biomanufacturing strategies under uncertainty: stainless steel versus disposable equipment for clinical trial material preparation.

PubMed

Farid, Suzanne S; Washbrook, John; Titchener-Hooker, Nigel J

2005-01-01

This paper presents the application of a decision-support tool, SIMBIOPHARMA, for assessing different manufacturing strategies under uncertainty for the production of biopharmaceuticals. SIMBIOPHARMA captures both the technical and business aspects of biopharmaceutical manufacture within a single tool that permits manufacturing alternatives to be evaluated in terms of cost, time, yield, project throughput, resource utilization, and risk. Its use for risk analysis is demonstrated through a hypothetical case study that uses the Monte Carlo simulation technique to imitate the randomness inherent in manufacturing subject to technical and market uncertainties. The case study addresses whether start-up companies should invest in a stainless steel pilot plant or use disposable equipment for the production of early phase clinical trial material. The effects of fluctuating product demands and titers on the performance of a biopharmaceutical company manufacturing clinical trial material are analyzed. The analysis highlights the impact of different manufacturing options on the range in possible outcomes for the project throughput and cost of goods and the likelihood that these metrics exceed a critical threshold. The simulation studies highlight the benefits of incorporating uncertainties when evaluating manufacturing strategies. Methods of presenting and analyzing information generated by the simulations are suggested. These are used to help determine the ranking of alternatives under different scenarios. The example illustrates the benefits to companies of using such a tool to improve management of their R&D portfolios so as to control the cost of goods.

Life Cycle Assessment of concrete manufacturing in small isolated states: the case of Cyprus

NASA Astrophysics Data System (ADS)

Chrysostomou, Chrystalla; Kylili, Angeliki; Nicolaides, Demetris; Fokaides, Paris A.

2017-10-01

Life Cycle Assessment (LCA) is an effective and valuable methodology for identifying the holistic sustainable behaviour of materials and products. It is also useful in analysing the impact a structure has over the course of its life cycle. Currently, there is no sufficient knowhow regarding the life cycle performance of building materials used in the case of small isolated states. This study focuses on the LCA of the production of concrete for the investigation of its environmental impact in isolated island states, using the case of Cyprus as an example. Four different scenarios for the production of 1 tonne of concrete are examined: (i) manufacturing of concrete by transporting raw materials from different locations around the island, (ii) manufacturing of concrete using alternative energy resources, (iii) manufacturing of concrete with reduced transportation needs, and (iv) on-site manufacturing of concrete. The results, in terms of environmental impacts of concrete produced, indicated that the use of renewable electricity instead of fossil-fuelled electricity in isolated states can drastically improve the environmental performance of the end product. Also, the minimisation of transportation distances and the use of locally available resources can also affect, to a degree, the environmental impact of concrete production.

Identifying viable regulatory and innovation pathways for regenerative medicine: a case study of cultured red blood cells.

PubMed

Mittra, J; Tait, J; Mastroeni, M; Turner, M L; Mountford, J C; Bruce, K

2015-01-25

The creation of red blood cells for the blood transfusion markets represents a highly innovative application of regenerative medicine with a medium term (5-10 year) prospect for first clinical studies. This article describes a case study analysis of a project to derive red blood cells from human embryonic stem cells, including the systemic challenges arising from (i) the selection of appropriate and viable regulatory protocols and (ii) technological constraints related to stem cell manufacture and scale up to clinical Good Manufacturing Practice (GMP) standard. The method used for case study analysis (Analysis of Life Science Innovation Systems (ALSIS)) is also innovative, demonstrating a new approach to social and natural science collaboration to foresight product development pathways. Issues arising along the development pathway include cell manufacture and scale-up challenges, affected by regulatory demands emerging from the innovation ecosystem (preclinical testing and clinical trials). Our discussion reflects on the efforts being made by regulators to adapt the current pharmaceuticals-based regulatory model to an allogeneic regenerative medicine product and the broader lessons from this case study for successful innovation and translation of regenerative medicine therapies, including the role of methodological and regulatory innovation in future development in the field. Copyright © 2014 The Authors. Published by Elsevier B.V. All rights reserved.

SOLVENT-BASED TO WATERBASED ADHESIVE-COATED SUBSTRATE RETROFIT - VOLUME III: LABEL MANUFACTURING CASE STUDY: NASHUA CORPORATION

EPA Science Inventory

This volume discusses Nashua Corporation's Omaha facility, a label and label stock manufacturing facility that no longer uses solvent-based adhesives. Information obtained includes issues related to the technical, economic, and environmental barriers and opportunities associated ...

Pollution prevention and the use of low-VOC/HAP coatings at wood furniture manufacturing facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marshall, A.M.; Spaight, J.L.; Jones, J.W.

1999-10-01

Midwest Research Institute, under a cooperative agreement with the Air Pollution Prevention and Control Division of the US Environmental Protection Agency`s (EPA`s) National Risk Management Research Laboratory, is conducting a study to identify wood furniture and cabinet manufacturing facilities that have converted to low-volatile organic compound/hazardous air pollutant (VOC/HAP) coatings and to develop case studies for those facilities. This paper discusses the progress of the project and pollution prevention options at wood furniture manufacturing facilities and the regulatory requirements (e.g., the National Emissions Standards for Hazardous Air Pollutants (NESHAP) for Wood Furniture Manufacturing Operations) that these facilities face.

New Whole-House Solutions Case Study: Northwest Energy Efficient Manufactured Housing Program High-Performance Test Homes - Pacific Northwest

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2015-05-01

This project represents the third phase of a multi-year effort to develop and bring to market a High Performance Manufactured Home (HPMH). In this project, the Northwest Energy Efficient Manufactured Housing Program worked with Building America Partnership for Improved Residential Construction and Bonneville Power Administration to help four factory homebuilders build prototype zero energy ready manufactured homes, resulting in what is expected to be a 30% savings relative to the Building America Benchmark. (The actual % savings varies depending on choice of heating equipment and climate zone). Previous phases of this project created a HPMH specification and prototyped individual measuresmore » from the package to obtain engineering approvals and develop preliminary factory construction processes. This case study describes the project team's work during 2014 to build prototype homes to the HPMH specifications and to monitor the homes for energy performance and durability. Monitoring is expected to continue into 2016.« less

National Manufacturing Strategy: Is a National Manufacturing Strategy Essential to National Security?

DTIC Science & Technology

2011-05-01

cycle found nearly a quarter of all homeowners owning more than their home was worth. 11 Both Paul Volcker and Warren Buffet arrived at similar...November 15, 2010; Warren Buffet , Testimony, Financial Crisis Inquiry Commission, June 2, 2010; “Subprime Mortgage Crisis,” http://en.wikipedia.org...overseas manufacturing. Case Study: Semiconductor Wafer Industry. The history of the semiconductor industry is an instructive account . It begins with

Wayne Manufacturing: A Teaching Case on the Detection of Misappropriation of Assets

ERIC Educational Resources Information Center

Orchard, Lou X.; Decker, Jeffrey L.; Kizirian, Tim

2007-01-01

This paper is a teaching case intended for use in an undergraduate auditing or fraud examination course. Students are introduced to Wayne Manufacturing, a medium-sized firm in the Midwestern U.S.A. that manufactures parts for companies such as General Motors (GM) and Ford. Wayne Manufacturing has some conditions present that put it at risk for…

Frontline Leaders: The Entry Point for Leadership Development in the Manufacturing Industry

ERIC Educational Resources Information Center

Liu, Lucy; McMurray, Adela J.

2004-01-01

This multi-method case study examined the roles, functions, capabilities, job satisfaction, strengths, weaknesses and skill gaps of frontline team leaders working on the shopfloor in the Australian automobile industry. The study was conducted in a large automobile manufacturing company employing 4,500 employees and rated as one of the top 22…

Alcoa North American Extrusions Implements Energy Use Assessments at Multiple Facilities: Office of Industrial Technologies (OIT) BestPractices Aluminum Assessment Case Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

U.S. Department of Energy

2001-08-05

This case study is the latest in a series on industrial firms who are implementing energy efficient technologies and system improvements into their manufacturing processes. The case studies document the activities, savings, and lessons learned on these projects.

How To Set Up Your Own Small Business. Service Company Case Study. Manufacturing Firm Case Study. Retail Store Case Study.

ERIC Educational Resources Information Center

Fallek, Max

This collection of case studies is intended for use in a course in setting up a small business. The first, a case study of the process of setting up a service company, covers analyzing the pros and cons of starting one's own business, assessing the competition and local market, and selecting a site for and financing the business. The principal…

Fixed obstructive lung disease among workers in the flavor-manufacturing industry--California, 2004-2007.

PubMed

2007-04-27

Bronchiolitis obliterans, a rare and life-threatening form of fixed obstructive lung disease, is known to be caused by exposure to noxious gases in occupational settings and has been described in workers in the microwave-popcorn industry who were exposed to artificial butter-flavoring chemicals, including diacetyl. In August 2004, the California Department of Health Services (CDHS) and Division of Occupational Safety and Health (Cal/OSHA) received the first report of a bronchiolitis obliterans diagnosis in a flavor-manufacturing worker in California. In April 2006, a second report was received of a case in a flavor-manufacturing worker from another company. Neither worker was employed in the microwave-popcorn industry; both were workers in the flavor-manufacturing industry, which produces artificial butter flavoring and other flavors such as cherry, almond, praline, jalapeno, and orange. Both workers had handled pure diacetyl, an ingredient in artificial butter and other flavorings, and additional chemicals involved in the manufacturing process. Studies have indicated that exposure to diacetyl causes severe respiratory epithelial injury in animals. Because the manufacture of flavorings involves more than 2,000 chemicals, workers in the general flavor-manufacturing industry are exposed to more chemicals than workers in the microwave-popcorn industry, which primarily uses butter flavorings. Food flavorings are designated "generally recognized as safe" when approved by the U.S. Food and Drug Administration; flavorings are not known to put consumers at risk for lung disease. This report describes the first two cases of bronchiolitis obliterans in flavor-manufacturing workers in California, the findings of the public health investigation, and the actions taken by state and federal agencies to prevent future cases of occupational bronchiolitis obliterans. To identify cases and reduce risk for lung disease from occupational exposure to flavorings, a timely, effective response is needed, including medical surveillance, exposure monitoring, and reduced exposure.

Utilities and manufacturers: Pioneering partnerships and their lessons for the 21st century

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bartsch, C.; DeVaul, D.

1994-12-31

Manufacturers who, in partnership with utilities, improved their production process through energy efficiency and waste minimization strategies are discussed. Frequently these investments changed the corporate culture and resulted in a commitment to continuous improvement that may ensure the industrialists adapt to a rapidly evolving marketplace. The Northeast-Midwest Institute`s work to record these case studies developed out of the observation that older manufacturing facilities too often are run until no longer competitive, then closed, and new plants are built somewhere else - increasingly overseas. Unemployment, poverty, and cycles of economic and social deterioration too often follow if a new economic basemore » cannot be created. At the same time, inefficient industrial plants tend to emit large quantities of waste materials; industry produces more than 600 million tons of hazardous wastes and approximately 13 billion tons of solid wastes each year. To help identify how to avoid such pitfalls, the Institute sought out manufacturers who modernized successfully. Case studies are presented that show that utilities often are instrumental in catalyzing change in their industrial partners. In fact, much can be gained from utilities and industries working together. Many manufacturers need technical and financial assistance to maintain peak productivity.« less

Corporate Energy Conservation Program for Alcoa North American Extrusions

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2001-08-01

This case study is the latest in a series on industrial firms who are implementing energy efficient technologies and system improvements into their manufacturing processes. The case studies document the activities, savings, and lessons learned on these projects.

A methodology for Manufacturing Execution Systems (MES) implementation

NASA Astrophysics Data System (ADS)

Govindaraju, Rajesri; Putra, Krisna

2016-02-01

Manufacturing execution system is information systems (IS) application that bridges the gap between IS at the top level, namely enterprise resource planning (ERP), and IS at the lower levels, namely the automation systems. MES provides a media for optimizing the manufacturing process as a whole in a real time basis. By the use of MES in combination with the implementation of ERP and other automation systems, a manufacturing company is expected to have high competitiveness. In implementing MES, functional integration -making all the components of the manufacturing system able to work well together, is the most difficult challenge. For this, there has been an industry standard that specifies the sub-systems of a manufacturing execution systems and defines the boundaries between ERP systems, MES, and other automation systems. The standard is known as ISA-95. Although the advantages from the use of MES have been stated in some studies, not much research being done on how to implement MES effectively. The purpose of this study is to develop a methodology describing how MES implementation project should be managed, utilising the support of ISA- 95 reference model in the system development process. A proposed methodology was developed based on a general IS development methodology. The developed methodology were then revisited based on the understanding about the specific charateristics of MES implementation project found in an Indonesian steel manufacturing company implementation case. The case study highlighted the importance of applying an effective requirement elicitation method during innitial system assessment process, managing system interfaces and labor division in the design process, and performing a pilot deployment before putting the whole system into operation.

Pollution prevention and the use of low-VOC/HAP coatings at wood furniture manufacturing facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marshall, A.M.; Spaight, J.L.; Jones, J.W.

1999-07-01

Midwest Research Institute, under a cooperative agreement with the Air Pollution Prevention and Control Division of the U.S. Environmental Protection Agency's (EPA's) National Risk Management Research Laboratory, is conducting a study to identify wood furniture and cabinet manufacturing facilities that have converted to low-volatile organic compound/hazardous air pollutant (VOC/HAP) coatings and to develop case studies for those facilities. The case studies include: (1) a discussion of the types of products each facility manufactures; (2) the types of low-VOC/HAP coatings each facility is using; (3) problems encountered in converting to low-VOC/HAP coatings; (4) equipment changes that were required; (5) the costsmore » associated with the conversion process, including capital costs associated with equipment purchases, research and development costs, and operating costs such as operator training in new application techniques; (6) advantages/disadvantages of the low-VOC/HAP coatings; and (7) customer feedback on products finished with the low-VOC/HAP coatings. The primary goals of the project are (1) to demonstrate that low-VOC/HAP coatings can be used successfully by many wood furniture manufacturing facilities, and (2) to assist other wood furniture manufacturing facilities in their conversion to low-VOC/HAP coatings, in particular facilities that do not have the resources to devote to extensive coatings research. This paper discusses the progress of the project and pollution prevention options at wood furniture manufacturing facilities and the regulatory requirements (e.g., the National Emissions Standards for Hazardous Air Pollutants [NESHAP] for Wood Furniture Manufacturing Operations) that these facilities face.« less

The make or buy debate: Considering the limitations of domestic production in Tanzania

PubMed Central

2012-01-01

Background In order to ensure their population’s regular access to essential medicines, many least developed countries and developing countries are faced with the policy question of whether to import or manufacture drugs locally, in particular for life-saving antiretroviral medicines for HIV/AIDS patients. In order for domestic manufacturing to be viable and cost-effective, the local industry must be able to compete with international suppliers of medicines by producing sufficiently low cost ARVs. Methods This paper considers the ‘make-or-buy’ dilemma by using Tanzania as a case study. Key informant interviews, event-driven observation, and purposive sampling of documents were used to evaluate the case study. The case study focused on Tanzania’s imitation technology transfer agreement to locally manufacture a first-line ARV (3TC + d4T + NVP), reverse engineering the ARV. Results Tanzania is limited by weak political support for the use of TRIPS flexibilities, limited production capacity for ARVs and limited competitiveness in both domestic and regional markets. The Ministry of Health and Social Welfare encourages the use of flexibilities while others push for increased IP protection. Insufficient production capacity and lack of access to donor-financed tenders make it difficult to obtain economies of scale and provide competitive prices. Conclusions Within the “make-or-buy” context, it was determined that there are significant limitations in domestic manufacturing for developing countries. The case study highlights the difficulty of governments to make use of economies of scale and produce low-cost medicines, attract technology transfer, and utilize the flexibilities of the WTO Agreement on Trade-Related Aspects of Intellectual Property Rights (TRIPS). The results demonstrate the importance of evaluating barriers to the use of TRIPS flexibilities and long-term planning across sectors in future technology transfer and manufacturing initiatives. PMID:22747578

Research on application information system integration platform in medicine manufacturing enterprise.

PubMed

Deng, Wu; Zhao, Huimin; Zou, Li; Li, Yuanyuan; Li, Zhengguang

2012-08-01

Computer and information technology popularizes in the medicine manufacturing enterprise for its potentials in working efficiency and service quality. In allusion to the explosive data and information of application system in current medicine manufacturing enterprise, we desire to propose a novel application information system integration platform in medicine manufacturing enterprise, which based on a combination of RFID technology and SOA, to implement information sharing and alternation. This method exploits the application integration platform across service interface layer to invoke the RFID middleware. The loose coupling in integration solution is realized by Web services. The key techniques in RFID event components and expanded role-based security access mechanism are studied in detail. Finally, a case study is implemented and tested to evidence our understanding on application system integration platform in medicine manufacturing enterprise.

Lean Thinking in Libraries: A Case Study on Improving Shelving Turnaround

ERIC Educational Resources Information Center

Kress, Nancy J.

2007-01-01

The University of Chicago's Joseph Regenstein Library Bookstacks Department has used process mapping and continuous improvement to successfully improve its overall operations. The most recent efforts focus on Lean manufacturing, an initiative centered on eliminating waste in manufacturing processes. The conversion of the Bookstacks Department from…

Case studies of pre-engineered and manufactured sound isolation rooms for music practice and radio broadcast

NASA Astrophysics Data System (ADS)

Probst, Ron N.; Rypka, Dann

2005-09-01

Pre-engineered and manufactured sound isolation rooms were developed to ensure guaranteed sound isolation while offering the unique ability to be disassembled and relocated without loss of acoustic performance. Case studies of pre-engineered sound isolation rooms used for music practice and various radio broadcast purposes are highlighted. Three prominent universities wrestle with the challenges of growth and expansion while responding to the specialized acoustic requirements of these spaces. Reduced state funding for universities requires close examination of all options while ensuring sound isolation requirements are achieved. Changing curriculum, renovation, and new construction make pre-engineered and manufactured rooms with guaranteed acoustical performance good investments now and for the future. An added benefit is the optional integration of active acoustics to provide simulations of other spaces or venues along with the benefit of sound isolation.

A Case Study of Rural Industrialization in Jamestown, North Dakota. Agricultural Economics Report No. 95.

ERIC Educational Resources Information Center

Helgeson, Delmer L.; Zink, Maurice J.

The study's objectives were to: (1) determine the criteria used by industry in the selection of an area as a plant site; (2) measure the interdependence and economic impact that a manufacturing sector has on an agriculturally dominated rural area; and (3) evaluate employees' attitudes toward their new jobs in manufacturing. Jamestown, North Dakota…

Electronic business model for small- and medium-sized manufacturing enterprises (SME): a case study

NASA Astrophysics Data System (ADS)

Yuen, Karina; Chung, Walter W.

2001-10-01

This paper identifies three essential factors (information infrastructure, executive information system and a new manufacturing paradigm) that are used to support the development of a new business model for competitiveness. They facilitate changes in organization structure in support of business transformation. A SME can source a good manufacturing practice using a model of academic-university collaboration to gain competitive advantage in the e-business world. The collaboration facilitates the change agents to use information systems development as a vehicle to increase the capability of executives in using information and knowledge management to gain higher responsiveness and customer satisfaction. The case company is used to illustrate the application of a web-based executive information system to interface internal communications with external operation. It explains where a good manufacturing practice may be re-applied by other SMEs to acquire skills as a learning organization grows in an extended enterprise setting.

Power Factor Study Reduces Energy Costs at Aluminum Extrusion Plant (Alcoa North American Extrusions)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2001-08-01

This case study is the latest in a series on industrial firms who are implementing energy efficient technologies and system improvements into their manufacturing processes. The case studies document the activities, savings, and lessons learned on these projects.

A system approach for reducing the environmental impact of manufacturing and sustainability improvement of nano-scale manufacturing

NASA Astrophysics Data System (ADS)

Yuan, Yingchun

This dissertation develops an effective and economical system approach to reduce the environmental impact of manufacturing. The system approach is developed by using a process-based holistic method for upstream analysis and source reduction of the environmental impact of manufacturing. The system approach developed consists of three components of a manufacturing system: technology, energy and material, and is useful for sustainable manufacturing as it establishes a clear link between manufacturing system components and its overall sustainability performance, and provides a framework for environmental impact reductions. In this dissertation, the system approach developed is applied for environmental impact reduction of a semiconductor nano-scale manufacturing system, with three case scenarios analyzed in depth on manufacturing process improvement, clean energy supply, and toxic chemical material selection. The analysis on manufacturing process improvement is conducted on Atomic Layer Deposition of Al2O3 dielectric gate on semiconductor microelectronics devices. Sustainability performance and scale-up impact of the ALD technology in terms of environmental emissions, energy consumption, nano-waste generation and manufacturing productivity are systematically investigated and the ways to improve the sustainability of the ALD technology are successfully developed. The clean energy supply is studied using solar photovoltaic, wind, and fuel cells systems for electricity generation. Environmental savings from each clean energy supply over grid power are quantitatively analyzed, and costs for greenhouse gas reductions on each clean energy supply are comparatively studied. For toxic chemical material selection, an innovative schematic method is developed as a visual decision tool for characterizing and benchmarking the human health impact of toxic chemicals, with a case study conducted on six chemicals commonly used as solvents in semiconductor manufacturing. Reliability of the schematic method is validated by comparing its benchmark results on 104 chemicals with that from the conventional Human Toxicity Potential (HTP) method. This dissertation concludes with discussions on environmental impact assessment of nanotechnologies and sustainability management of nano-particles. As nano-manufacturing is emerging for wide industrial applications, improvement and expansion of the system approach would be valuable for use in the environmental management of nano-manufacturing and in the risk control of nano-particles in the interests of public health and the environment.

Alcoa North American Extrusions Implements Energy Use Assessments at Multiple Facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2001-08-01

This case study is the latest in a series on industrial firms who are implementing energy efficient technologies and system improvements into their manufacturing processes. The case studies document the activities, savings, and lessons learned on these projects.

Analyzing industrial energy use through ordinary least squares regression models

NASA Astrophysics Data System (ADS)

Golden, Allyson Katherine

Extensive research has been performed using regression analysis and calibrated simulations to create baseline energy consumption models for residential buildings and commercial institutions. However, few attempts have been made to discuss the applicability of these methodologies to establish baseline energy consumption models for industrial manufacturing facilities. In the few studies of industrial facilities, the presented linear change-point and degree-day regression analyses illustrate ideal cases. It follows that there is a need in the established literature to discuss the methodologies and to determine their applicability for establishing baseline energy consumption models of industrial manufacturing facilities. The thesis determines the effectiveness of simple inverse linear statistical regression models when establishing baseline energy consumption models for industrial manufacturing facilities. Ordinary least squares change-point and degree-day regression methods are used to create baseline energy consumption models for nine different case studies of industrial manufacturing facilities located in the southeastern United States. The influence of ambient dry-bulb temperature and production on total facility energy consumption is observed. The energy consumption behavior of industrial manufacturing facilities is only sometimes sufficiently explained by temperature, production, or a combination of the two variables. This thesis also provides methods for generating baseline energy models that are straightforward and accessible to anyone in the industrial manufacturing community. The methods outlined in this thesis may be easily replicated by anyone that possesses basic spreadsheet software and general knowledge of the relationship between energy consumption and weather, production, or other influential variables. With the help of simple inverse linear regression models, industrial manufacturing facilities may better understand their energy consumption and production behavior, and identify opportunities for energy and cost savings. This thesis study also utilizes change-point and degree-day baseline energy models to disaggregate facility annual energy consumption into separate industrial end-user categories. The baseline energy model provides a suitable and economical alternative to sub-metering individual manufacturing equipment. One case study describes the conjoined use of baseline energy models and facility information gathered during a one-day onsite visit to perform an end-point energy analysis of an injection molding facility conducted by the Alabama Industrial Assessment Center. Applying baseline regression model results to the end-point energy analysis allowed the AIAC to better approximate the annual energy consumption of the facility's HVAC system.

Cobalt asthma in metalworkers from an automotive engine valve manufacturer.

PubMed

Walters, G I; Robertson, A S; Moore, V C; Burge, P S

2014-07-01

Cobalt asthma has previously been described in cobalt production workers, diamond polishers and glassware manufacturers. To describe a case series of occupational asthma (OA) due to cobalt, identified at the Birmingham Heartlands Occupational Lung Disease Unit, West Midlands, UK. Cases of cobalt asthma from a West Midlands' manufacturer of automotive engine valves, diagnosed between 1996 and 2005, were identified from the SHIELD database of OA. Case note data on demographics, employment status, asthma symptoms and diagnostic tests, including spirometry, peak expiratory flow (PEF) measurements, skin prick testing (SPT) and specific inhalational challenge (SIC) tests to cobalt chloride, were gathered, and descriptive statistics used to illustrate the data. The natural history of presentations has been described in detail, as well as a case study of one of the affected workers. Fourteen metalworkers (86% male; mean age 44.9 years) were diagnosed with cobalt asthma between 1996 and 2005. Workers were principally stellite grinders, stellite welders or machine setter-operators. All workers had positive Occupational Asthma SYStem analyses of serial PEF measurements, and sensitization to cobalt chloride was demonstrated in nine workers, by SPT or SIC. We have described a series of 14 workers with cobalt asthma from the automotive manufacturing industry, with objective evidence for sensitization. Health care workers should remain vigilant for cobalt asthma in the automotive manufacturing industry. © The Author 2014. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Evaluation of direct and indirect additive manufacture of maxillofacial prostheses.

PubMed

Eggbeer, Dominic; Bibb, Richard; Evans, Peter; Ji, Lu

2012-09-01

The efficacy of computer-aided technologies in the design and manufacture of maxillofacial prostheses has not been fully proven. This paper presents research into the evaluation of direct and indirect additive manufacture of a maxillofacial prosthesis against conventional laboratory-based techniques. An implant/magnet-retained nasal prosthesis case from a UK maxillofacial unit was selected as a case study. A benchmark prosthesis was fabricated using conventional laboratory-based techniques for comparison against additive manufactured prostheses. For the computer-aided workflow, photogrammetry, computer-aided design and additive manufacture (AM) methods were evaluated in direct prosthesis body fabrication and indirect production using an additively manufactured mould. Qualitative analysis of position, shape, colour and edge quality was undertaken. Mechanical testing to ISO standards was also used to compare the silicone rubber used in the conventional prosthesis with the AM material. Critical evaluation has shown that utilising a computer-aided work-flow can produce a prosthesis body that is comparable to that produced using existing best practice. Technical limitations currently prevent the direct fabrication method demonstrated in this paper from being clinically viable. This research helps prosthesis providers understand the application of a computer-aided approach and guides technology developers and researchers to address the limitations identified.

Effect of manufacturing process sequence on the corrosion resistance characteristics of coated metallic bipolar plates

NASA Astrophysics Data System (ADS)

Dur, Ender; Cora, Ömer Necati; Koç, Muammer

2014-01-01

Metallic bipolar plate (BPP) with high corrosion and low contact resistance, durability, strength, low cost, volume, and weight requirements is one of the critical parts of the PEMFC. This study is dedicated to understand the effect of the process sequence (manufacturing then coating vs. coating then manufacturing) on the corrosion resistance of coated metallic bipolar plates. To this goal, three different PVD coatings (titanium nitride (TiN), chromium nitride (CrN), zirconium nitride (ZrN)), with three thicknesses, (0.1, 0.5, 1 μm) were applied on BPPs made of 316L stainless steel alloy before and after two types of manufacturing (i.e., stamping or hydroforming). Corrosion test results indicated that ZrN coating exhibited the best corrosion protection while the performance of TiN coating was the lowest among the tested coatings and thicknesses. For most of the cases tested, in which coating was applied before manufacturing, occurrence of corrosion was found to be more profound than the case where coating was applied after manufacturing. Increasing the coating thickness was found to improve the corrosion resistance. It was also revealed that hydroformed BPPs performed slightly better than stamped BPPs in terms of the corrosion behavior.

Long-term health experience of jet engine manufacturing workers: VIII. glioblastoma incidence in relation to workplace experiences with parts and processes.

PubMed

Marsh, Gary M; Youk, Ada O; Buchanich, Jeanine M; Downing, Sarah; Kennedy, Kathleen J; Esmen, Nurtan A; Hancock, Roger P; Lacey, Steven E; Pierce, Jennifer S; Fleissner, Mary Lou

2013-06-01

To determine whether glioblastoma (GB) incidence rates among jet engine manufacturing workers were associated with workplace experiences with specific parts produced and processes performed. Subjects were 210,784 workers employed between 1952 and 2001. We conducted nested case-control and cohort incidence studies with focus on 277 GB cases. We estimated time experienced with 16 part families, 4 process categories, and 32 concurrent part-process combinations with 20 or more GB cases. In both the cohort and case-control studies, none of the part families, process categories, or both considered was associated with increased GB risk. If not due to chance alone, the not statistically significantly elevated GB rates in the North Haven plant may reflect external occupational factors or nonoccupational factors unmeasured in the current evaluation.

Team Building.

ERIC Educational Resources Information Center

1996

This document contains four papers presented at a symposium moderated by Allen Church at the 1996 conference of the Academy of Human Resource Development. "Teambuilding Intervention Strategy Development: A Case Study of Two Midwestern Manufacturing Industries" (Paul E. Brauchle, David W. Wright) discusses a qualitative case study of employee…

Case Study: Commercialization of sweet sorghum juice clarification for large-scale syrup manufacture

USDA-ARS?s Scientific Manuscript database

The precipitation and burning of insoluble granules of starch from sweet sorghum juice on heating coils prevented the large scale manufacture of syrup at a new industrial plant in Missouri, USA. To remove insoluble starch granules, a series of small and large-scale experiments were conducted at the...

The Industrial Manufacturing Technician Apprenticeship. Work-Based Learning in Action

ERIC Educational Resources Information Center

Scott, Geri

2016-01-01

This case study, one of a series of publications exploring effective and inclusive models of work-based learning, finds that entry-level occupations in manufacturing have historically been considered unskilled jobs for which little or no training is necessary. As a consequence, employers have experienced high turnover among new-hires, and…

The Evolutionary Process of Secondary Innovation in the Context of Globalization: A Case Study

ERIC Educational Resources Information Center

Wu, Xiaobo; Xu, Guannan; Ma, Rufei; Du, Jian

2008-01-01

This paper examines the evolutionary process of secondary innovation in a typical Chinese equipment manufacturing firm in the context of globalization and elaborates how to achieve latecomer's advantage from imitation to innovation. Four stages are identified in the process of international manufacturing: the equipment import stage, the production…

Analysis of Agility Performance of Supply Chain: A Case Study on Indian Automotive Manufacturer

NASA Astrophysics Data System (ADS)

Routroy, S.; Sharma, S.; Bhardwaj, A.

2018-04-01

Manufacturing companies should understand the changing customer needs and expectations, access and defend the competitive pressure, anticipate and manage the uncertain demand and supply chain risk, and implement the appropriate technology to survive and excel in today’s marketplace. Therefore, they are moving away from mass production (i.e. lean supply chain) to one based on fast-responsiveness and flexibility, capitalizing on the rapid advancement in internet technologies and factory-on-demand mode of production (i.e. agile supply chain). It is observed that manufacturing companies in India in general and automotive supply chain in specific are compelled to cultivate supply chain agility for enhancing its performance level on continuous basis and comparing its supply chain agility performance with competitors to survive and sustain in the competitive business environment. Therefore, a methodology is proposed to evaluate the supply chain agility of a manufacturing supply chain and compare its performance level with competitors using Fuzzy Analytic Hierarchy Process and Taguchi Loss Function. A case study is developed and the proposed methodology is applied to Indian automotive supply chain for explaining the salient features of it.

A Process Management System for Networked Manufacturing

NASA Astrophysics Data System (ADS)

Liu, Tingting; Wang, Huifen; Liu, Linyan

With the development of computer, communication and network, networked manufacturing has become one of the main manufacturing paradigms in the 21st century. Under the networked manufacturing environment, there exist a large number of cooperative tasks susceptible to alterations, conflicts caused by resources and problems of cost and quality. This increases the complexity of administration. Process management is a technology used to design, enact, control, and analyze networked manufacturing processes. It supports efficient execution, effective management, conflict resolution, cost containment and quality control. In this paper we propose an integrated process management system for networked manufacturing. Requirements of process management are analyzed and architecture of the system is presented. And a process model considering process cost and quality is developed. Finally a case study is provided to explain how the system runs efficiently.

Inpatient hospital admission rates for nonmalignant respiratory disease among workers exposed to metal removal fluids at a U.S. automobile manufacturer.

PubMed

Reeve, Gordon R; Stout, Allen W; Hands, David; Curry, Emmanuel

2003-11-01

This study was undertaken to determine the impact of exposure to metal removal fluids (MRFs) on the respiratory health of exposed workers. The outcome measure selected was the rate of hospital admissions for nonmalignant respiratory disease episodes as determined from healthcare insurance claims data. A cohort of MRF-exposed employees was assembled from 11 manufacturing facilities where MRFs were extensively used in the manufacture of automotive engines, transmissions, and other machined parts. The MRF-exposed cohort included 20,434 employees of such facilities who worked at any time from 1993 through 1997. A non-MRF-exposed cohort was assembled from other employees of the same company during the same time period, but working in warehouse operations and other manufacturing facilities that did not use MRFs or any known respiratory sensitizing agents. The non-exposed cohort included 8681 employees. The crude hospital admission rate for the MRF-exposed cohort was 44 percent higher than that of the non-exposed cohort over the 5-year study period (6.67 vs. 4.62 per 1000 person years at risk, p < 0.05). With age adjustment, the MRF population's rate was still 35 percent higher, and still statistically significant. A nested case-control study was also conducted to determine whether the risk of hospital admission increased with the level of MRF exposure in the population working in MRF plants. The industrial hygiene reconstruction found the levels of exposures of both cases and controls to be very low, with the vast majority of study subjects (more than 90%) having exposures of less than 0.5 mg/m(3). The case-control study did not find any association between increased levels of MRF exposure and risk of hospitalization. The study did document an elevated risk of hospitalization among a sizable population employed in manufacturing operations where MRFs are used.

Risk Assessment at the Cosmetic Product Manufacturer by Expert Judgment Method

NASA Astrophysics Data System (ADS)

Vtorushina, A. N.; Larionova, E. V.; Mezenceva, I. L.; Nikonova, E. D.

2017-05-01

A case study was performed in a cosmetic product manufacturer. We have identified the main risk factors of occupational accidents and their causes. Risk of accidents is assessed by the expert judgment method. Event tree for the most probable accident is built and recommendations on improvement of occupational health and safety protection system at the cosmetic product manufacturer are developed. The results of this paper can be used to develop actions to improve the occupational safety and health system in the chemical industry.

Gender differences on the job satisfaction in the phase of implementing advanced manufacturing technology in the Chinese manufacturing firms.

PubMed

Yu, Na; Shen, Li Ming; Lewark, Siegfried

2012-01-01

This research gave an effort to study on gender differences in the job satisfaction for technological innovation at Chinese manufacturing firm. The exploratory study was conducted in four Chinese furniture manufacturing firms, which are all in the phases of introducing advanced manufacturing system. The results of statistical analysis show that general satisfaction of female employees to their jobs is significantly higher than male employees. In addition, supervisory satisfaction of female employees is significantly higher than male employees. The findings of the study reveal that activities are suggested to be carried out to increase the job satisfaction of male employees, especially improve communication and relationship between the managerial and the non-managerial levels in the innovation process. In addition, the higher job satisfaction of female employees could be considered a positive factor for the successful implementation of AMT in the technological innovation, although male employees are still dominated work force in the case study firms.

A PetriNet-Based Approach for Supporting Traceability in Cyber-Physical Manufacturing Systems

PubMed Central

Huang, Jiwei; Zhu, Yeping; Cheng, Bo; Lin, Chuang; Chen, Junliang

2016-01-01

With the growing popularity of complex dynamic activities in manufacturing processes, traceability of the entire life of every product has drawn significant attention especially for food, clinical materials, and similar items. This paper studies the traceability issue in cyber-physical manufacturing systems from a theoretical viewpoint. Petri net models are generalized for formulating dynamic manufacturing processes, based on which a detailed approach for enabling traceability analysis is presented. Models as well as algorithms are carefully designed, which can trace back the lifecycle of a possibly contaminated item. A practical prototype system for supporting traceability is designed, and a real-life case study of a quality control system for bee products is presented to validate the effectiveness of the approach. PMID:26999141

A PetriNet-Based Approach for Supporting Traceability in Cyber-Physical Manufacturing Systems.

PubMed

Huang, Jiwei; Zhu, Yeping; Cheng, Bo; Lin, Chuang; Chen, Junliang

2016-03-17

With the growing popularity of complex dynamic activities in manufacturing processes, traceability of the entire life of every product has drawn significant attention especially for food, clinical materials, and similar items. This paper studies the traceability issue in cyber-physical manufacturing systems from a theoretical viewpoint. Petri net models are generalized for formulating dynamic manufacturing processes, based on which a detailed approach for enabling traceability analysis is presented. Models as well as algorithms are carefully designed, which can trace back the lifecycle of a possibly contaminated item. A practical prototype system for supporting traceability is designed, and a real-life case study of a quality control system for bee products is presented to validate the effectiveness of the approach.

Evaluation of the Effectiveness of the Integration of a LITEE Case Study for a Freshman Level Mechanical Engineering Course at The University of Toledo

ERIC Educational Resources Information Center

Franchetti, Matthew

2011-01-01

The purpose of this paper is to report the findings of the integration of a manufacturing case study to a freshman level mechanical engineering course at The University of Toledo. The approach to integrate this case study into the class was completed via weekly assignments analyzing the case, small group discussion, and weekly group discussion.…

Irritable Bowel Syndrome and Complementary Health Practices: What the Science Says

MedlinePlus

... controlled trials on various herbal preparations; however, the methodological quality of most of these studies is poor. ... if improperly manufactured. A 2012 systematic review of case reports and case series concluded that using certain ...

Manufacturing methods of a composite cell case for a Ni-Cd battery

NASA Technical Reports Server (NTRS)

Bauer, J. L.

1979-01-01

Basic manufacturing method refinements for using graphite epoxy material for a nickel cadmium battery cell case were performed to demonstrate production feasibility. The various facets of production scale-up, i.e., process and tooling development, together with material and process control, were integrated into a comprehensive manufacturing process that assures production reproducibility and product uniformity. Test results substantiate that a battery cell case produced from graphite epoxy pre-impregnated material, utilizing the internal pressure bag fabrication method, is feasible.

Workplace Literacy: The Effects of an In-house Program on the Organization.

ERIC Educational Resources Information Center

Fretz, Barbara

The effects of an in-house workplace literacy program on an organization are examined. A small Canadian manufacturing plant that began a workplace literacy program called Learning in the Workplace in 1990 was the site of this case study research. The plant was CCL Custom Manufacturing, which specialized in household powder-based products. Four…

Does Lean Production Sacrifice Learning in a Manufacturing Environment? An Action Learning Case Study.

ERIC Educational Resources Information Center

Scott, Fiona M.; Butler, Jim; Edwards, John

2001-01-01

An action learning program was implemented by a manufacturer using lean production practices. Action learning practices were accommodated during times of stability, but abandoned in times of crisis. The meaning of work in this organizational culture excluded all practices, such as reflection, that were not visible and targeted at immediate…

Building Lean Supply Chain and Manufacturing Skills through an Interactive Case Study

ERIC Educational Resources Information Center

Ozelkan, Ertunga C.; Teng, S. Gary; Johnson, Thomas; Benson, Tom; Nestvogel, Dean

2007-01-01

With the ongoing global pressure to cut costs and focus on quality, many companies have been implementing "lean manufacturing" concepts to survive in the competitive marketplace. Thus it is imperative that engineering and business graduates are equipped with the lean principles, and are ready to take ownership of lean initiatives as they enter the…

Mechanics and energetics in tool manufacture and use: a synthetic approach.

PubMed

Wang, Liyu; Brodbeck, Luzius; Iida, Fumiya

2014-11-06

Tool manufacture and use are observed not only in humans but also in other animals such as mammals, birds and insects. Manufactured tools are used for biomechanical functions such as effective control of fluids and small solid objects and extension of reaching. These tools are passive and used with gravity and the animal users' own energy. From the perspective of evolutionary biology, manufactured tools are extended phenotypes of the genes of the animal and exhibit phenotypic plasticity. This incurs energetic cost of manufacture as compared to the case with a fixed tool. This paper studies mechanics and energetics aspects of tool manufacture and use in non-human beings. Firstly, it investigates possible mechanical mechanisms of the use of passive manufactured tools. Secondly, it formulates the energetic cost of manufacture and analyses when phenotypic plasticity benefits an animal tool maker and user. We take a synthetic approach and use a controlled physical model, i.e. a robot arm. The robot is capable of additively manufacturing scoop and gripper structures from thermoplastic adhesives to pick and place fluid and solid objects, mimicking primates and birds manufacturing tools for a similar function. We evaluate the effectiveness of tool use in pick-and-place and explain the mechanism for gripper tools picking up solid objects with a solid-mechanics model. We propose a way to formulate the energetic cost of tool manufacture that includes modes of addition and reshaping, and use it to analyse the case of scoop tools. Experiment results show that with a single motor trajectory, the robot was able to effectively pick and place water, rice grains, a pebble and a plastic box with a scoop tool or gripper tools that were manufactured by itself. They also show that by changing the dimension of scoop tools, the energetic cost of tool manufacture and use could be reduced. The work should also be interesting for engineers to design adaptive machines. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

Mechanics and energetics in tool manufacture and use: a synthetic approach

PubMed Central

Wang, Liyu; Brodbeck, Luzius; Iida, Fumiya

2014-01-01

Tool manufacture and use are observed not only in humans but also in other animals such as mammals, birds and insects. Manufactured tools are used for biomechanical functions such as effective control of fluids and small solid objects and extension of reaching. These tools are passive and used with gravity and the animal users' own energy. From the perspective of evolutionary biology, manufactured tools are extended phenotypes of the genes of the animal and exhibit phenotypic plasticity. This incurs energetic cost of manufacture as compared to the case with a fixed tool. This paper studies mechanics and energetics aspects of tool manufacture and use in non-human beings. Firstly, it investigates possible mechanical mechanisms of the use of passive manufactured tools. Secondly, it formulates the energetic cost of manufacture and analyses when phenotypic plasticity benefits an animal tool maker and user. We take a synthetic approach and use a controlled physical model, i.e. a robot arm. The robot is capable of additively manufacturing scoop and gripper structures from thermoplastic adhesives to pick and place fluid and solid objects, mimicking primates and birds manufacturing tools for a similar function. We evaluate the effectiveness of tool use in pick-and-place and explain the mechanism for gripper tools picking up solid objects with a solid-mechanics model. We propose a way to formulate the energetic cost of tool manufacture that includes modes of addition and reshaping, and use it to analyse the case of scoop tools. Experiment results show that with a single motor trajectory, the robot was able to effectively pick and place water, rice grains, a pebble and a plastic box with a scoop tool or gripper tools that were manufactured by itself. They also show that by changing the dimension of scoop tools, the energetic cost of tool manufacture and use could be reduced. The work should also be interesting for engineers to design adaptive machines. PMID:25209405

Additive Manufacturing in Production: A Study Case Applying Technical Requirements

NASA Astrophysics Data System (ADS)

Ituarte, Iñigo Flores; Coatanea, Eric; Salmi, Mika; Tuomi, Jukka; Partanen, Jouni

Additive manufacturing (AM) is expanding the manufacturing capabilities. However, quality of AM produced parts is dependent on a number of machine, geometry and process parameters. The variability of these parameters affects the manufacturing drastically and therefore standardized processes and harmonized methodologies need to be developed to characterize the technology for end use applications and enable the technology for manufacturing. This research proposes a composite methodology integrating Taguchi Design of Experiments, multi-objective optimization and statistical process control, to optimize the manufacturing process and fulfil multiple requirements imposed to an arbitrary geometry. The proposed methodology aims to characterize AM technology depending upon manufacturing process variables as well as to perform a comparative assessment of three AM technologies (Selective Laser Sintering, Laser Stereolithography and Polyjet). Results indicate that only one machine, laser-based Stereolithography, was feasible to fulfil simultaneously macro and micro level geometrical requirements but mechanical properties were not at required level. Future research will study a single AM system at the time to characterize AM machine technical capabilities and stimulate pre-normative initiatives of the technology for end use applications.

A study on the applications of AI in finishing of additive manufacturing parts

NASA Astrophysics Data System (ADS)

Fathima Patham, K.

2017-06-01

Artificial intelligent and computer simulation are the technological powerful tools for solving complex problems in the manufacturing industries. Additive Manufacturing is one of the powerful manufacturing techniques that provide design flexibilities to the products. The products with complex shapes are directly manufactured without the need of any machining and tooling using Additive Manufacturing. However, the main drawback of the components produced using the Additive Manufacturing processes is the quality of the surfaces. This study aims to minimize the defects caused during Additive Manufacturing with the aid of Artificial Intelligence. The developed AI system has three layers, each layer is trying to eliminate or minimize the production errors. The first layer of the AI system optimizes the digitization of the 3D CAD model of the product and hence reduces the stair case errors. The second layer of the AI system optimizes the 3D printing machine parameters in order to eliminate the warping effect. The third layer of AI system helps to choose the surface finishing technique suitable for the printed component based on the Degree of Complexity of the product and the material. The efficiency of the developed AI system was examined on the functional parts such as gears.

Compressed Air System Redesign Results in Increased Production at a Fuel System Plant (Caterpillar Fuel Systems Pontiac Plant)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2001-06-01

This case study is one in a series on industrial firms who are implementing energy efficient technologies and system improvements into their manufacturing processes. This case study documents the activities, savings, and lessons learned on the Caterpillar's Pontiac Plant project.

JOB REDESIGN FOR OLDER WORKERS--CASE STUDIES.

ERIC Educational Resources Information Center

ROTHBERG, HERMAN J.

INDUSTRIAL ESTABLISHMENTS SUCCESSFULLY USED METHODS OF JOB REDESIGN TO MAINTAIN THE EMPLOYMENT AND PRODUCTIVITY, AS WELL AS THE MORALE, OF AGING EMPLOYEES. EXAMPLES OF JOB REDESIGN WERE FOUND IN A WIDE VARIETY OF MANUFACTURING INDUSTRIES. CASE STUDIES WERE MADE IN PLANTS PRODUCING AIRCRAFT ENGINES, ALUMINUM FRAMING, BUILDING MATERIALS, CARPETS,…

Upgrade of Compressed Air Control System Reduces Energy Costs at Michelin Tire Plant. Office of Industrial Technologies (OIT) BestPractices Project Case Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2002-01-01

This case study highlights the upgraded compressed air system at a Michelin tire manufacturing plant in Spartanburg, South Carolina. The controls upgrade project enabled multiple compressor operation without blow-off, and significantly reduced energy costs.

Performance Evaluation Process.

ERIC Educational Resources Information Center

1998

This document contains four papers from a symposium on the performance evaluation process and human resource development (HRD). "Assessing the Effectiveness of OJT (On the Job Training): A Case Study Approach" (Julie Furst-Bowe, Debra Gates) is a case study of the effectiveness of OJT in one of a high-tech manufacturing company's product…

[Empirical studies on some drugs for patent lawsuits in the age of manufacturing patents].

PubMed

Yamakawa, Koji; Nishitani, Kiyoshi

2009-01-01

Empirical studies on patent lawsuits for some drugs by author (K.Y.) from 1953-1998, are described. Case 1: One of the authors (K.Y.) clarified that silylmethylation of a penicillin derivative gave either N, O-disilylmethylated product or O-monosilylmethylated product. However, only O-silylmethylated product was obtained after the usual work-up (Fig. 1). Case 2: A point under discussion of the trial is whether the reported manufacturing process of "metoclopramide" is possible or not. One of the authors (K. Y.) clarified the possibility by means of a careful synthetic experiment (Fig. 2). Case 3: The essential effective structure of herbicides, Roundup (Monsanto Co.) and Sulfosate (Stoph Co.), was the same in highly diluted solution (Fig. 3). Case 4: Cimetidine has been prepared by the Oxy procedure (SKB Co.), but another cimetidine (Fujimoto Co.) was prepared by the Lek procedure. Is it true? Experimental preparations of both cimetidines by the respective Oxy and Lek processes, were achieved by the authors. The cimetidine in the tablet named "Cylock" by Fujimoto Pharm. Co., Ltd. should be manufactured by the Oxy process on the basis of the by-products analysis (Fig. 4). Finally, a short history of patents in Japan from 1899-1975 is described.

Characterization of Effect of Support Structures in Laser Additive Manufacturing of Stainless Steel

NASA Astrophysics Data System (ADS)

Järvinen, Jukka-Pekka; Matilainen, Ville; Li, Xiaoyun; Piili, Heidi; Salminen, Antti; Mäkelä, Ismo; Nyrhilä, Olli

Laser additive manufacturing (LAM) of stainless steel is a layer wisetechnology for fabricating 3D parts from metal powder via selectively melting powder with laser beam. Support structures play a significant role in LAM process as they help to remove heat away from the process and on the other hand hold the work piece in its place. A successful design of support structures can help to achievea building process fast and inexpensive with high quality. Aimof this study was to characterize the usability of two types of support structures: web and tube supports. Purpose of this studywas also to analyze how suitable they are in two industrial application cases: case for dental application and case for jewelry application. It was concluded that the removability of web supports was much better than tube supports. It was noticed that support structures are an important part of LAM process and they strongly affect the manufacturability and the end quality of the part.

Global Value Chain and Manufacturing Analysis on Geothermal Power Plant Turbines: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akar, Sertac; Augustine, Chad R; Kurup, Parthiv

The global geothermal electricity market has significantly grown over the last decade and is expected to reach a total installed capacity of 18.4 GWe in 2021 (GEA, 2016). Currently, geothermal project developers customize the size of the power plant to fit the resource being developed. In particular, the turbine is designed and sized to optimize efficiency and resource utilization for electricity production; most often, other power plant components are then chosen to complement the turbine design. These custom turbine designs demand one-off manufacturing processes, which result in higher manufacturing setup costs, longer lead-times, and higher capital costs overall in comparisonmore » to larger-volume line manufacturing processes. In contrast, turbines produced in standard increments, manufactured in larger volumes, could result in lower costs per turbine. This study focuses on analysis of the global supply chain and manufacturing costs for Organic Rankine Cycle (ORC) turboexpanders and steam turbines used in geothermal power plants. In this study, we developed a manufacturing cost model to identify requirements for equipment, facilities, raw materials, and labor. We analyzed three different cases 1) 1 MWe geothermal ORC turboexpander 2) 5 MWe ORC turboexpander and 3) 20 MWe geothermal steam turbine, and calculated the cost of manufacturing the major components, such as the impellers/blades, shaft/rotor, nozzles, inlet guide lanes, disks, and casings. Then we used discounted cash flow (DCF) analysis to calculate the minimum sustainable price (MSP). MSP is the minimum price that a company must sell its product for in order to pay back the capital and operating expenses during the plant lifetime (CEMAC, 2017). The results showed that MSP could highly vary between 893 dollar/kW and 30 dollar/kW based on turbine size, standardization and volume of manufacturing. The analysis also showed that the economy of scale applies both to the size of the turbine and the number manufactured in a single run. Sensitivity analysis indicated these savings come largely from reduced labor costs for design and engineering and manufacturing setup.« less

Global Value Chain and Manufacturing Analysis on Geothermal Power Plant Turbines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akar, Sertac; Augustine, Chad R; Kurup, Parthiv

The global geothermal electricity market has significantly grown over the last decade and is expected to reach a total installed capacity of 18.4 GWe in 2021 (GEA, 2016). Currently, geothermal project developers customize the size of the power plant to fit the resource being developed. In particular, the turbine is designed and sized to optimize efficiency and resource utilization for electricity production; most often, other power plant components are then chosen to complement the turbine design. These custom turbine designs demand one-off manufacturing processes, which result in higher manufacturing setup costs, longer lead-times, and higher capital costs overall in comparisonmore » to larger-volume line manufacturing processes. In contrast, turbines produced in standard increments, manufactured in larger volumes, could result in lower costs per turbine. This study focuses on analysis of the global supply chain and manufacturing costs for Organic Rankine Cycle (ORC) turboexpanders and steam turbines used in geothermal power plants. In this study, we developed a manufacturing cost model to identify requirements for equipment, facilities, raw materials, and labor. We analyzed three different cases 1) 1 MWe geothermal ORC turboexpander 2) 5 MWe ORC turboexpander and 3) 20 MWe geothermal steam turbine, and calculated the cost of manufacturing the major components, such as the impellers/blades, shaft/rotor, nozzles, inlet guide lanes, disks, and casings. Then we used discounted cash flow (DCF) analysis to calculate the minimum sustainable price (MSP). MSP is the minimum price that a company must sell its product for in order to pay back the capital and operating expenses during the plant lifetime (CEMAC, 2017). The results showed that MSP could highly vary between 893 dollar/kW and 30 dollar/kW based on turbine size, standardization and volume of manufacturing. The analysis also showed that the economy of scale applies both to the size of the turbine and the number manufactured in a single run. Sensitivity analysis indicated these savings come largely from reduced labor costs for design and engineering and manufacturing setup.« less

Occupational risk factors of lung cancer: a hospital based case-control study

PubMed Central

Droste, J. H.; Weyler, J. J.; Van Meerbeeck, J. P.; Vermeire, P. A.; van Sprundel, M. P.

1999-01-01

OBJECTIVES: To investigate the relation between lung cancer and exposure to occupational carcinogens in a highly industrialised region in western Europe. METHODS: In a case-control study 478 cases and 536 controls, recruited from 10 hospitals in the Antwerp region, were interviewed. Cases were male patients with histologically confirmed lung cancer; controls were male patients without cancer or primary lung diseases. Data were collected by questionnaires to obtain information on occupations, exposures, and smoking history. Job titles were coded with the Office of Populations, Censuses and Surveys industrial classification. Exposure was assessed by self report and by job-task exposure matrix. Exposure odds ratios were calculated with logistic regression analysis adjusted for age, smoking history, and marital and socio-economic status. RESULTS: A job history in the categories manufacturing of transport equipment other than automobiles (for example, shipyard workers), transport support services (for example, dockers), and manufacturing of metal goods (for example, welders) was significantly associated with lung cancer (odds ratios (ORs) 2.3, 1.6, and 1.6 respectively). These associations were independent of smoking, education, civil, and economic status. Self reported exposure to potential carcinogens did not show significant associations with lung cancer, probably due to nondifferential misclassification. When assessed by job-task exposure matrix, exposure to molybdenum, mineral oils, and chromium were significantly associated with lung cancer. A strong association existed between smoking and lung cancer: OR of ex- smokers 4.2, OR of current smokers 14.5 v non-smokers. However, smoking did not confound the relation between occupational exposure and lung cancer. CONCLUSIONS: The study has shown a significant excess risk of lung cancer among workers in manufacturing of metal goods, manufacturing of transport equipment (other than automobiles), and transport support services. Assessment of exposure to specific carcinogens resulted in significant associations of chromium, mineral oils, and molybdenum with lung cancer. This study is, to our knowledge, the first study reporting a significant association between occupational exposure to molybdenum and lung cancer.   PMID:10472306

Training Implications of Technological Change in Manufacturing in New Industrial Countries: The Case of Ireland. Training Policies Discussion Paper No. 14.

ERIC Educational Resources Information Center

International Labour Office, Geneva (Switzerland).

This report on Ireland is one in a series of studies for a research project designed to identify training and education policies pursued by governments and individual firms that have contributed to innovation, technological adaptation, and skill development in manufacturing. Part 1 describes Ireland's economic, social, and educational structure…

Towards a Service-Oriented Enterprise: The Design of a Cloud Business Integration Platform in a Medium-Sized Manufacturing Enterprise

ERIC Educational Resources Information Center

Stamas, Paul J.

2013-01-01

This case study research followed the two-year transition of a medium-sized manufacturing firm towards a service-oriented enterprise. A service-oriented enterprise is an emerging architecture of the firm that leverages the paradigm of services computing to integrate the capabilities of the firm with the complementary competencies of business…

Issues in nanocomposite ceramic engineering: focus on processing and properties of alumina-based composites.

PubMed

Palmero, Paola; Kern, Frank; Sommer, Frank; Lombardi, Mariangela; Gadow, Rainer; Montanaro, Laura

2014-12-30

Ceramic nanocomposites, containing at least one phase in the nanometric dimension, have received special interest in recent years. They have, in fact, demonstrated increased performance, reliability and lifetime with respect to monolithic ceramics. However, a successful approach to the production of tailored composite nanostructures requires the development of innovative concepts at each step of manufacturing, from the synthesis of composite nanopowders, to their processing and sintering.This review aims to deepen understanding of some of the critical issues associated with the manufacturing of nanocomposite ceramics, focusing on alumina-based composite systems. Two case studies are presented and briefly discussed. The former illustrates the benefits, in terms of sintered microstructure and related mechanical properties, resulting from the application of an engineering approach to a laboratory-scale protocol for the elaboration of nanocomposites in the system alumina-ZrO2-YAG (yttrium aluminium garnet). The latter illustrates the manufacturing of alumina-based composites for large-scale applications such as cutting tools, carried out by an injection molding process. The need for an engineering approach to be applied in all processing steps is demonstrated also in this second case study, where a tailored manufacturing process is required to obtain the desired results.

Dilemmas of Transfer Pricing Comparability Analysis in Manufacturing Entities. Polish-Czech Case Study

NASA Astrophysics Data System (ADS)

Sulik-Górecka, Aleksandra

2018-06-01

Modern manufacturing entities often operate in capital groups, and their role is sometimes limited to the function of cost centers. From the legal point of view, however, they are separate entities obliged to apply transfer pricing regulations. Meeting the requirements of the arm's length principle can be very difficult at this time, given the relationships and conflicts of interest in the capital group. Complexity increases in capital groups operating in different countries, due to differences in tax regulations. The main purpose of the paper is to demonstrate that the need to valuate the sale of finished goods to a manufacturing entity, which is a subject to a different tax jurisdiction, may lead to a problem of compliance with the arm's length principle. In addition, the paper proposes a methodology for comparability analysis that may be used by manufacturing entities to defend conditions of setting transfer pricing. The paper presents the different functional profiles of manufacturing entities and points out the difficulties that they may encounter when preparing the comparability analysis. It has also been noted that there are differences in transfer pricing regulations in different countries, for example by analyzing Polish and Czech regulations. The lack of uniform benchmarking legislation can cause inconsistencies in the selection of comparable data, resulting in differences in transfer pricing. The paper uses the method of legal regulation review and analysis of results of published studies concerning the scope of transfer pricing and comparability analysis. The paper also adopts a case study analysis.

Manufacturing methods of a composite cell case for a Ni-Cd battery

NASA Technical Reports Server (NTRS)

Bauer, J. L.; Bogner, R. S.; Lowe, E. P.; Orlowski, E.

1979-01-01

Graphite epoxy material for a nickel cadmium battery cell case has been evaluated and determined to perform in the simulated environment of the battery. The basic manufacturing method requires refinement to demonstrate production feasibility. The various facets of production scale-up, i.e., process and tooling development together with material and process control, have been integrated into a comprehensive manufacturing process that assures production reproducibility and product uniformity. Test results substantiate that a battery cell case produced from graphite epoxy pre-impregnated material utilizing internal pressure bag fabrication method is feasible.

Reporting of occupational injury and illness in the semiconductor manufacturing industry.

PubMed

McCurdy, S A; Schenker, M B; Samuels, S J

1991-01-01

In the United States, occupational illness and injury cases meeting specific reporting criteria are recorded on company Occupational Safety and Health Administration (OSHA) 200 logs; case description data are submitted to participating state agencies for coding and entry in the national Supplementary Data System (SDS). We evaluated completeness of reporting (the percentage of reportable cases that were recorded in the company OSHA 200 log) in the semiconductor manufacturing industry by reviewing company health clinic records for 1984 of 10 manufacturing sites of member companies of a national semiconductor manufacturing industry trade association. Of 416 randomly selected work-related cases, 101 met OSHA reporting criteria. Reporting completeness was 60 percent and was lowest for occupational illnesses (44 percent). Case-description data from 150 reported cases were submitted twice to state coding personnel to evaluate coding reliability. Reliability was high (kappa 0.82-0.93) for "nature," "affected body part," "source," and "type" variables. Coding for the SDS appears reliable; reporting completeness may be improved by use of a stepwise approach by company personnel responsible for reporting decisions.

Methods and Case Studies for Teaching and Learning about Failure and Safety.

ERIC Educational Resources Information Center

Bignell, Victor

1999-01-01

Discusses methods for analyzing case studies of failures of technological systems. Describes two distance learning courses that compare standard models of failure and success with the actuality of given scenarios. Provides teaching and learning materials and information sources for application to aspects of design, manufacture, inspection, use,…

The Relationships between Organizational Culture and Environmental Scanning: A Case Study.

ERIC Educational Resources Information Center

Miller, Jerry P.

1994-01-01

Based on interview and survey data from 220 upper- and middle-level managers within a Fortune 500 manufacturing firm, this case study describes how differences in organizational values influence the frequency with which decision makers use oral, written, and electronic sources of information for environmental scanning. (91 references) (LRW)

Data Mining CMMSs: How to Convert Data into Knowledge.

PubMed

Fennigkoh, Larry; Nanney, D Courtney

2018-01-01

Although the healthcare technology management (HTM) community has decades of accumulated medical device-related maintenance data, little knowledge has been gleaned from these data. Finding and extracting such knowledge requires the use of the well-established, but admittedly somewhat foreign to HTM, application of inferential statistics. This article sought to provide a basic background on inferential statistics and describe a case study of their application, limitations, and proper interpretation. The research question associated with this case study involved examining the effects of ventilator preventive maintenance (PM) labor hours, age, and manufacturer on needed unscheduled corrective maintenance (CM) labor hours. The study sample included more than 21,000 combined PM inspections and CM work orders on 2,045 ventilators from 26 manufacturers during a five-year period (2012-16). A multiple regression analysis revealed that device age, manufacturer, and accumulated PM inspection labor hours all influenced the amount of CM labor significantly (P < 0.001). In essence, CM labor hours increased with increasing PM labor. However, and despite the statistical significance of these predictors, the regression analysis also indicated that ventilator age, manufacturer, and PM labor hours only explained approximately 16% of all variability in CM labor, with the remainder (84%) caused by other factors that were not included in the study. As such, the regression model obtained here is not suitable for predicting ventilator CM labor hours.

Present Status and Future Growth of Advanced Maintenance Technology and Strategy in US Manufacturing.

PubMed

Jin, Xiaoning; Weiss, Brian A; Siegel, David; Lee, Jay

2016-01-01

The goals of this paper are to 1) examine the current practices of diagnostics, prognostics, and maintenance employed by United States (U.S.) manufacturers to achieve productivity and quality targets and 2) to understand the present level of maintenance technologies and strategies that are being incorporated into these practices. A study is performed to contrast the impact of various industry-specific factors on the effectiveness and profitability of the implementation of prognostics and health management technologies, and maintenance strategies using both surveys and case studies on a sample of U.S. manufacturing firms ranging from small to mid-sized enterprises (SMEs) to large-sized manufacturing enterprises in various industries. The results obtained provide important insights on the different impacts of specific factors on the successful adoption of these technologies between SMEs and large manufacturing enterprises. The varying degrees of success with respect to current maintenance programs highlight the opportunity for larger manufacturers to improve maintenance practices and consider the use of advanced prognostics and health management (PHM) technology. This paper also provides the existing gaps, barriers, future trends, and roadmaps for manufacturing PHM technology and maintenance strategy.

Present Status and Future Growth of Advanced Maintenance Technology and Strategy in US Manufacturing

PubMed Central

Jin, Xiaoning; Weiss, Brian A.; Siegel, David; Lee, Jay

2016-01-01

The goals of this paper are to 1) examine the current practices of diagnostics, prognostics, and maintenance employed by United States (U.S.) manufacturers to achieve productivity and quality targets and 2) to understand the present level of maintenance technologies and strategies that are being incorporated into these practices. A study is performed to contrast the impact of various industry-specific factors on the effectiveness and profitability of the implementation of prognostics and health management technologies, and maintenance strategies using both surveys and case studies on a sample of U.S. manufacturing firms ranging from small to mid-sized enterprises (SMEs) to large-sized manufacturing enterprises in various industries. The results obtained provide important insights on the different impacts of specific factors on the successful adoption of these technologies between SMEs and large manufacturing enterprises. The varying degrees of success with respect to current maintenance programs highlight the opportunity for larger manufacturers to improve maintenance practices and consider the use of advanced prognostics and health management (PHM) technology. This paper also provides the existing gaps, barriers, future trends, and roadmaps for manufacturing PHM technology and maintenance strategy. PMID:28058173

Lean Manufacturing Principles Improving the Targeting Process

DTIC Science & Technology

2012-06-08

author has familiarity with Lean manufacturing principles. Third, Lean methods have been used in different industries and have proven adaptable to the...92 The case study also demonstrates the multi organizational application of VSM, JIT and the 5S method ...new members not knowing the process, this will serve as a start point for the developing of understanding. Within the Food industry we observed “the

Training Implications of Technological Change in Manufacturing in New Industrial Countries: The Case of Yugoslavia. Training Policies Discussion Paper No. 15.

ERIC Educational Resources Information Center

Matejic, Vlastimir; Kamhi, Meri

This report is a study of the training implications of technological change in manufacturing in Yugoslavia. Part 1 analyzes the general technological and educational infrastructure in Yugoslavia. The sources of technology as well as the present state and future prospects of technological research are described. Education is discussed in terms of…

Overview of Additive Manufacturing Initiatives at NASA Marshall Space Flight Center

NASA Technical Reports Server (NTRS)

Clinton, R. G., Jr.

2018-01-01

NASA's In Space Manufacturing Initiative (ISM) includes: The case for ISM - why; ISM path to exploration - results from the 3D Printing In Zero-G Technology Demonstration - ISM challenges; In space Robotic Manufacturing and Assembly (IRMA); Additive construction. Additively Manufacturing (AM) development for liquid rocket engine space flight hardware. MSFC standard and specification for additively manufactured space flight hardware. Summary.

Scheduling job shop - A case study

NASA Astrophysics Data System (ADS)

Abas, M.; Abbas, A.; Khan, W. A.

2016-08-01

The scheduling in job shop is important for efficient utilization of machines in the manufacturing industry. There are number of algorithms available for scheduling of jobs which depend on machines tools, indirect consumables and jobs which are to be processed. In this paper a case study is presented for scheduling of jobs when parts are treated on available machines. Through time and motion study setup time and operation time are measured as total processing time for variety of products having different manufacturing processes. Based on due dates different level of priority are assigned to the jobs and the jobs are scheduled on the basis of priority. In view of the measured processing time, the times for processing of some new jobs are estimated and for efficient utilization of the machines available an algorithm is proposed and validated.

Affordable Design: A Methodolgy to Implement Process-Based Manufacturing Cost into the Traditional Performance-Focused Multidisciplinary Design Optimization

NASA Technical Reports Server (NTRS)

Bao, Han P.; Samareh, J. A.

2000-01-01

The primary objective of this paper is to demonstrate the use of process-based manufacturing and assembly cost models in a traditional performance-focused multidisciplinary design and optimization process. The use of automated cost-performance analysis is an enabling technology that could bring realistic processbased manufacturing and assembly cost into multidisciplinary design and optimization. In this paper, we present a new methodology for incorporating process costing into a standard multidisciplinary design optimization process. Material, manufacturing processes, and assembly processes costs then could be used as the objective function for the optimization method. A case study involving forty-six different configurations of a simple wing is presented, indicating that a design based on performance criteria alone may not necessarily be the most affordable as far as manufacturing and assembly cost is concerned.

Design and Evaluation of Glass/epoxy Composite Blade and Composite Tower Applied to Wind Turbine

NASA Astrophysics Data System (ADS)

Park, Hyunbum

2018-02-01

In the study, the analysis and manufacturing of small class wind turbine blade was performed. In the structural design, firstly the loading conditions are defined through the load case analysis. The proposed structural configuration of blade has a sandwich type composite structure with the E-glass/Epoxy face sheets and the Urethane foam core for lightness, structural stability, low manufacturing cost and easy manufacturing process. And also, this work proposes a design procedure and results of tower for the small scale wind turbine systems. Structural analysis of blade including load cases, stress, deformation, buckling, vibration and fatigue life was performed using the finite element method, the load spectrum analysis and the Miner rule. Moreover, investigation on structural safety of tower was verified through structural analysis by FEM. The manufacturing of blade and tower was performed based on structural design. In order to investigate the designed structure, the structural tests were conducted and its results were compared with the calculated results. It is confirmed that the final proposed blade and tower meet the design requirements.

Control of formaldehyde and TVOC emission from wood-based flooring composites at various manufacturing processes by surface finishing.

PubMed

Kim, Sumin

2010-04-15

This paper assesses the reproducibility of testing formaldehyde and TVOC emission behavior from wood flooring composites bonded by urea-formaldehyde resin at various manufacturing steps for surface finishing materials. The surface adhesion step of laminate flooring for this research was divided into two steps; HDF only and HDF with LPMs. In the case of engineered flooring, the manufacturing steps were divided into three steps; plywood only, fancy veneer bonded on plywood and UV coated on fancy veneer with plywood. Formaldehyde and VOCs emission decreased at the process of final surface finishing materials; LPMs were applied on the surface of HDF for laminate flooring. Although emissions increased when fancy veneer was bonded onto plywood in the case of engineered flooring, emission was dramatically reduced up to similar level with plywood only when final surface finishing; UV-curable coating was applied on fancy veneer. This study suggests that formaldehyde and VOCs emission from floorings can be controlled at manufacturing steps for surface finishing. 2009 Elsevier B.V. All rights reserved.

A case study on Simulation and Design optimization to improve Productivity in cooling tower manufacturing industry

NASA Astrophysics Data System (ADS)

Pranav Nithin, R.; Gopikrishnan, S.; Sumesh, A.

2018-02-01

Cooling towers are the heat transfer devices commonly found in industries which are used to extract the high temperature from the coolants and make it reusable in various plants. Basically, the cooling towers has Fills made of PVC sheets stacked together to increase the surface area exposure of the cooling liquid flowing through it. This paper focuses on the study in such a manufacturing plant where fills are being manufactured. The productivity using the current manufacturing method was only 6 to 8 fills per day, where the ideal capacity was of 14 fills per day. In this plant manual labor was employed in the manufacturing process. A change in the process modification designed and implemented will help the industry to increase the productivity to 14. In this paper, initially the simulation study was done using ARENA the simulation package and later the new design was done using CAD Package and validated using Ansys Mechanical APDL. It’s found that, by the implementation of the safe design the productivity can be increased to 196 Units.

P.C. disposal decisions: a banking industry case study

NASA Astrophysics Data System (ADS)

Shah, Sejal P.; Sarkis, Joseph

2002-02-01

The service industry and the manufacturing industry are interlinked in a supply chain situation. Part of the effectiveness of some manufacturing industry environmental performance based on remanufacturing and recycling is dependent on service industry decisions. In the information technology arena, personal computers (PCs) are the hard equipment of the service industry. The end-of-life decisions made by the service industry, and in this case the banking industry will have implications for the amount of systems within the waste or reverse logistics stream for manufacturers. Looking at some of the issues (and presenting a model for evaluation) related to decision making concerning end-of-life disposition for PCs is something this paper investigates. The analytical hierarchy process (AHP) is applied in this circumstance. The development of the model, its application, and results, provide the basis for much of the discussion in this paper.

100 Successful Years of Vertical Lift Gates of Bhatghar Dam—Design, Manufacturing, Erection, and Maintenance: A Case Study

NASA Astrophysics Data System (ADS)

Mahajan, Dinakar Rajaram

2017-09-01

The Bhatghar dam is having 81 vertical lift gates (fixed wheel type) on waste ways. The design of these gates is so beautiful and based on simple principles of science and engineering that these gates outlast for 100 years without failure, performing their intended purpose satisfactorily. It is achieved by meticulous design, manufacturing, erection, subsequent use and maintenance practices. It has become guiding and inspiration for further practices in design, manufacturing, erection, and maintenance for dam gates as well as all other disciplines of engineering today.

Inter-Organizational Trust in EDI Adoption: The Case of Ford Motor Company and PBR Limited in Australia.

ERIC Educational Resources Information Center

Ratnasingam, Pauline

2001-01-01

This study examines behavioral dimensions of trading partner trust in EDI (electronic data interchange) adoption via a qualitative interpretative case study conducted between an automotive manufacturer (Ford Motor Company) in Australia and their first tier supplier, PBR Limited. Findings suggest that trust is important for cooperative long-term…

Integrated Dynamic Process Planning and Scheduling in Flexible Manufacturing Systems via Autonomous Agents

NASA Astrophysics Data System (ADS)

Nejad, Hossein Tehrani Nik; Sugimura, Nobuhiro; Iwamura, Koji; Tanimizu, Yoshitaka

Process planning and scheduling are important manufacturing planning activities which deal with resource utilization and time span of manufacturing operations. The process plans and the schedules generated in the planning phase shall be modified in the execution phase due to the disturbances in the manufacturing systems. This paper deals with a multi-agent architecture of an integrated and dynamic system for process planning and scheduling for multi jobs. A negotiation protocol is discussed, in this paper, to generate the process plans and the schedules of the manufacturing resources and the individual jobs, dynamically and incrementally, based on the alternative manufacturing processes. The alternative manufacturing processes are presented by the process plan networks discussed in the previous paper, and the suitable process plans and schedules are searched and generated to cope with both the dynamic status and the disturbances of the manufacturing systems. We initiatively combine the heuristic search algorithms of the process plan networks with the negotiation protocols, in order to generate suitable process plans and schedules in the dynamic manufacturing environment. A simulation software has been developed to carry out case studies, aimed at verifying the performance of the proposed multi-agent architecture.

Going Large or Going Small in Plant Design: Comparison between a P.P. with three small Kaplan turbines and a P.P. with just one Large Kaplan turbine

NASA Astrophysics Data System (ADS)

Castro-Otero, C.

2017-04-01

Very often small turbine manufacturers are requested to produce sizeable turbines, too large in terms of physical dimensions, power or designing capacity. In these cases clever alternative solutions should be found to meet customers’ needs. For instance: in the old times twin runner Francis turbines were an option instead of one large machine, or if a too large Pelton turbine cannot be manufactured or designed, a good option is to install a medium size Francis and a small Pelton. Likewise, a similar approach needs to be taken should the manufacturer be asked for a too large Kaplan. Facing this situation a good option is to install three or more small Kaplan turbines. This particular case was studied in depth and after all the considerations had been made, the following question arouse: Is this a way out for the manufacturer or is it really the best option for the customer? The choice made as a way out for the manufacturer became the best option for the customer and a success for both parties. This paper aims to encourage developers and engineering firms to search for more options than the traditional one to find the best option in plant design.

Product Liability: Extent of ’Litigation Explosion’ in Federal Courts Questioned.

DTIC Science & Technology

1988-01-28

Dow Pharmaceuticals Inc., the manufacturer of bendectin , a morning-sickness drug. We also gathered information on product liability cases filed in...Shield, bendectin , asbestos, and metal-cutting and metal-forming equipment. We obtained these data from previously conducted studies, manufacturers, and...growth in filings unrelated to the Dalkon Shield, bendectin , and asbestos does not appear to have been rapidly accelerating or explo- sive. These are

Biosimilarity Versus Manufacturing Change: Two Distinct Concepts.

PubMed

Declerck, Paul; Farouk-Rezk, Mourad; Rudd, Pauline M

2016-02-01

As products of living cells, biologics are far more complicated than small molecular-weight drugs not only with respect to size and structural complexity but also their sensitivity to manufacturing processes and post-translational changes. Most of the information on the manufacturing process of biotherapeutics is proprietary and hence not fully accessible to the public. This information gap represents a key challenge for biosimilar developers and plays a key role in explaining the differences in regulatory pathways required to demonstrate biosimilarity versus those required to ensure that a change in manufacturing process did not have implications on safety and efficacy. Manufacturing process changes are frequently needed for a variety of reasons including response to regulatory requirements, up scaling production, change in facility, change in raw materials, improving control of quality (consistency) or optimising production efficiency. The scope of the change is usually a key indicator of the scale of analysis required to evaluate the quality. In most cases, where the scope of the process change is limited, only quality and analytical studies should be sufficient while comparative clinical studies can be required in case of major changes (e.g., cell line changes). Biosimilarity exercises have been addressed differently by regulators on the understanding that biosimilar developers start with fundamental differences being a new cell line and also a knowledge gap of the innovator's processes, including culture media, purification processes, and potentially different formulations, and are thus required to ensure that differences from innovators do not result in differences in efficacy and safety.

Burns from illegal drug manufacture: case series and management.

PubMed

Porter, C J W; Armstrong, J R

2004-01-01

This case series presents our experience with burns sustained while manufacturing illegal drugs. All adult burn admissions in an 18-month period were retrospectively reviewed. All patients suspected of sustaining burns from illegal drug manufacture were contacted. Information regarding the burn mechanism was sought. Nine of the 64 adult burn admissions were caused by explosions during the manufacture of cannabis oil. Young males with hand and face burns were heavily represented. First-aid treatment was often ignored in favor of hiding incriminating evidence. Only two patients gave honest admission histories. Illegal drug manufacture is becoming more common as synthetic drugs become more consumer desirable. Burns sustained may be thermal and/or chemical. Dishonest patient histories negatively influence burn management. A high level of suspicion is required for diagnosing and treating burns from illegal drug manufacture. Public education is unlikely to be effective as the financial rewards outweigh the perceived risks.

14 CFR 1260.57 - New technology.

Code of Federal Regulations, 2013 CFR

2013-01-01

... operate, in case of a machine or system; and, in each case, under such conditions as to establish that the... items include, but are not limited to, new processes, machines, manufactures, and compositions of matter, and improvements to, or new applications of, existing processes, machines, manufactures, and...

14 CFR 1260.57 - New technology.

Code of Federal Regulations, 2012 CFR

2012-01-01

... operate, in case of a machine or system; and, in each case, under such conditions as to establish that the... items include, but are not limited to, new processes, machines, manufactures, and compositions of matter, and improvements to, or new applications of, existing processes, machines, manufactures, and...

Critical operations capabilities in a high cost environment: a multiple case study

NASA Astrophysics Data System (ADS)

Sansone, C.; Hilletofth, P.; Eriksson, D.

2018-04-01

Operations capabilities have been a popular research area for many years and several frameworks have been proposed in the literature. The current frameworks do not take specific contexts into consideration, for instance a high cost environment. This research gap is of particular interest since a manufacturing relocation process has been ongoing the last decades, leading to a huge amount of manufacturing being moved from high to low cost environments. The purpose of this study is to identify critical operations capabilities in a high cost environment. The two research questions were: What are the critical operations capabilities dimensions in a high cost environment? What are the critical operations capabilities in a high cost environment? A multiple case study was conducted and three Swedish manufacturing firms were selected. The study was based on the investigation of an existing framework of operations capabilities. The main dimensions of operations capabilities included in the framework were: cost, quality, delivery, flexibility, service, innovation and environment. Each of the dimensions included two or more operations capabilities. The findings confirmed the validity of the framework and its usefulness in a high cost environment and a new operations capability was revealed (employee flexibility).

Continued investigation of solid propulsion economics. Task 1B: Large solid rocket motor case fabrication methods - Supplement process complexity factor cost technique

NASA Technical Reports Server (NTRS)

Baird, J.

1967-01-01

This supplement to Task lB-Large Solid Rocket Motor Case Fabrication Methods supplies additional supporting cost data and discusses in detail the methodology that was applied to the task. For the case elements studied, the cost was found to be directly proportional to the Process Complexity Factor (PCF). The PCF was obtained for each element by identifying unit processes that are common to the elements and their alternative manufacturing routes, by assigning a weight to each unit process, and by summing the weighted counts. In three instances of actual manufacture, the actual cost per pound equaled the cost estimate based on PCF per pound, but this supplement, recognizes that the methodology is of limited, rather than general, application.

A Case Study of Human Resource Development Professionals' Decision Making in Vendor Selection for Employee Development: A Degrees-of-Freedom Analysis

ERIC Educational Resources Information Center

Cathcart, Stephen Michael

2016-01-01

This mixed method study examines HRD professionals' decision-making processes when making an organizational purchase of training. The study uses a case approach with a degrees of freedom analysis. The data to analyze will examine how HRD professionals in manufacturing select outside vendors human resource development programs for training,…

Comparison of the Delay in Processing Time and Protective Plastic Cases in Two Phosphor Plate Systems

PubMed Central

Aktan, Ali Murat; Çiftçi, Mehmet Ertuğrul; Akgünlü, Faruk

2012-01-01

Objective. The purpose of this study was to analyze two phosphor plate systems (PSPs) (Dürr Dental, Digora Optime) according to their scanning delay and protective plastic case performances. Methods. Two PSPs using an aluminum step wedge were exposed. These plates were placed in three different protective plastic cases (manufacturers' original cases, black case, and white case) before obtaining the radiographs and were then processed immediately and 1, 5, 10, 30, 60, 120, 240, and 480 min after exposure. Mean gray values (MGVs) of the 3rd, 5th, 7th, and 9th steps of the wedges were compared using ANOVA. Results. Statistically significant differences were found between the two PSPs (P < 0.001). ANOVA revealed that the MGVs of four steps of the wedges were significantly different from each other for all scan delays (P < 0.001). MGVs increased with increasing scanning delay, except the group with Dürr plates in their original cases. Reduction in image quality began 5 min after exposure in the other Dürr plate groups. Conclusions. Within the limitations of the current study, it can be concluded that scanning delay causes a reduction in image quality, and using the manufacturer's original protective case will result in better performance of PSPs. PMID:23213301

Comparison of the delay in processing time and protective plastic cases in two phosphor plate systems.

PubMed

Aktan, Ali Murat; Ciftçi, Mehmet Ertuğrul; Akgünlü, Faruk

2012-01-01

The purpose of this study was to analyze two phosphor plate systems (PSPs) (Dürr Dental, Digora Optime) according to their scanning delay and protective plastic case performances. Two PSPs using an aluminum step wedge were exposed. These plates were placed in three different protective plastic cases (manufacturers' original cases, black case, and white case) before obtaining the radiographs and were then processed immediately and 1, 5, 10, 30, 60, 120, 240, and 480 min after exposure. Mean gray values (MGVs) of the 3rd, 5th, 7th, and 9th steps of the wedges were compared using ANOVA. Statistically significant differences were found between the two PSPs (P < 0.001). ANOVA revealed that the MGVs of four steps of the wedges were significantly different from each other for all scan delays (P < 0.001). MGVs increased with increasing scanning delay, except the group with Dürr plates in their original cases. Reduction in image quality began 5 min after exposure in the other Dürr plate groups. Within the limitations of the current study, it can be concluded that scanning delay causes a reduction in image quality, and using the manufacturer's original protective case will result in better performance of PSPs.

48 CFR 1852.227-70 - New technology.

Code of Federal Regulations, 2011 CFR

2011-10-01

... method; or to operate, in case of a machine or system; and, in each case, under such conditions as to... contract. Reportable items include, but are not limited to, new processes, machines, manufactures, and compositions of matter, and improvements to, or new applications of, existing processes, machines, manufactures...

14 CFR § 1260.57 - New technology.

Code of Federal Regulations, 2014 CFR

2014-01-01

... operate, in case of a machine or system; and, in each case, under such conditions as to establish that the... items include, but are not limited to, new processes, machines, manufactures, and compositions of matter, and improvements to, or new applications of, existing processes, machines, manufactures, and...

A PageRank-based reputation model for personalised manufacturing service recommendation

NASA Astrophysics Data System (ADS)

Zhang, W. Y.; Zhang, S.; Guo, S. S.

2017-05-01

The number of manufacturing services for cross-enterprise business collaborations is increasing rapidly because of the explosive growth of Web service technologies. This trend demands intelligent and robust models to address information overload in order to enable efficient discovery of manufacturing services. In this paper, we present a personalised manufacturing service recommendation approach, which combines a PageRank-based reputation model and a collaborative filtering technique in a unified framework for recommending the right manufacturing services to an active service user for supply chain deployment. The novel aspect of this research is adapting the PageRank algorithm to a network of service-oriented multi-echelon supply chain in order to determine both user reputation and service reputation. In addition, it explores the use of these methods in alleviating data sparsity and cold start problems that hinder traditional collaborative filtering techniques. A case study is conducted to validate the practicality and effectiveness of the proposed approach in recommending the right manufacturing services to active service users.

Towards Knowledge Management for Smart Manufacturing.

PubMed

Feng, Shaw C; Bernstein, William Z; Hedberg, Thomas; Feeney, Allison Barnard

2017-09-01

The need for capturing knowledge in the digital form in design, process planning, production, and inspection has increasingly become an issue in manufacturing industries as the variety and complexity of product lifecycle applications increase. Both knowledge and data need to be well managed for quality assurance, lifecycle-impact assessment, and design improvement. Some technical barriers exist today that inhibit industry from fully utilizing design, planning, processing, and inspection knowledge. The primary barrier is a lack of a well-accepted mechanism that enables users to integrate data and knowledge. This paper prescribes knowledge management to address a lack of mechanisms for integrating, sharing, and updating domain-specific knowledge in smart manufacturing. Aspects of the knowledge constructs include conceptual design, detailed design, process planning, material property, production, and inspection. The main contribution of this paper is to provide a methodology on what knowledge manufacturing organizations access, update, and archive in the context of smart manufacturing. The case study in this paper provides some example knowledge objects to enable smart manufacturing.

A Manufacturing Cost and Supply Chain Analysis of SiC Power Electronics Applicable to Medium-Voltage Motor Drives

DOE Office of Scientific and Technical Information (OSTI.GOV)

Horowitz, Kelsey; Remo, Timothy; Reese, Samantha

Wide bandgap (WBG) semiconductor devices are increasingly being considered for use in certain power electronics applications, where they can improve efficiency, performance, footprint, and, potentially, total system cost compared to systems using traditional silicon (Si) devices. Silicon carbide (SiC) devices in particular -- which are currently more mature than other WBG devices -- are poised for growth in the coming years. Today, the manufacturing of SiC wafers is concentrated in the United States, and chip production is split roughly equally between the United States, Japan, and Europe. Established contract manufacturers located throughout Asia typically carry out manufacturing of WBG powermore » modules. We seek to understand how global manufacturing of SiC components may evolve over time by illustrating the regional cost drivers along the supply chain and providing an overview of other factors that influence where manufacturing is sited. We conduct this analysis for a particular case study where SiC devices are used in a medium-voltage motor drive.« less

Development of the supply chain oriented quality assurance system for aerospace manufacturing SMEs and its implementation perspectives

NASA Astrophysics Data System (ADS)

Hussein, Abdullahi; Cheng, Kai

2016-10-01

Aerospace manufacturing SMEs are continuously facing the challenge on managing their supply chain and complying with the aerospace manufacturing quality standard requirement due to their lack of resources and the nature of business. In this paper, the ERP system based approach is presented to quality control and assurance work in light of seamless integration of in-process production data and information internally and therefore managing suppliers more effectively and efficiently. The Aerospace Manufacturing Quality Assurance Standard (BS/EN9100) is one of the most recognised and essential protocols for developing the industry-operated-and-driven quality assurance systems. The research investigates using the ERP based system as an enabler to implement BS/EN9100 quality management system at manufacturing SMEs and the associated implementation and application perspectives. An application case study on a manufacturing SME is presented by using the SAP based implementation, which helps further evaluate and validate the approach and application system development.

Framework for adaptive interoperability of manufacturing enterprises (FAIME): a case study

NASA Astrophysics Data System (ADS)

Sims, John E.; Chu, Bei Tseng B.; Long, Junshen; Matthews, Mike; Barnes, Johnny G.; Jones, Chris H.; Anderson, Rayne A.; Lambert, Russ; Drake, Doug C.; Hamilton, Mark A.; Connard, Mark

1997-01-01

In todays global economy, manufacturing industries require to connect disparate applications seamlessly. They require not only to exchange data and transactions, but present a single business process image to their employees in the office, headquarters, and on the plant floor. Also, it is imperative that small and medium size manufacturing companies deploy manufacturing execution systems applications in conjunction with modern enterprise resource programs for cycle time reduction and better quality. This paper presents the experiences and reflections on a project that created a tool set to assist the above be accomplished not only in a shorter cycle time, with a better predictable quality, and with an object oriented framework, but also a tool set that allows the manufacturer to still use legacy applications. This framework has the capability of plug-and- play so that future migrations and re-engineering of processes are more productive.

A Study on Human Oriented Autonomous Distributed Manufacturing System —Real-time Scheduling Method Based on Preference of Human Operators

NASA Astrophysics Data System (ADS)

Iwamura, Koji; Kuwahara, Shinya; Tanimizu, Yoshitaka; Sugimura, Nobuhiro

Recently, new distributed architectures of manufacturing systems are proposed, aiming at realizing more flexible control structures of the manufacturing systems. Many researches have been carried out to deal with the distributed architectures for planning and control of the manufacturing systems. However, the human operators have not yet been discussed for the autonomous components of the distributed manufacturing systems. A real-time scheduling method is proposed, in this research, to select suitable combinations of the human operators, the resources and the jobs for the manufacturing processes. The proposed scheduling method consists of following three steps. In the first step, the human operators select their favorite manufacturing processes which they will carry out in the next time period, based on their preferences. In the second step, the machine tools and the jobs select suitable combinations for the next machining processes. In the third step, the automated guided vehicles and the jobs select suitable combinations for the next transportation processes. The second and third steps are carried out by using the utility value based method and the dispatching rule-based method proposed in the previous researches. Some case studies have been carried out to verify the effectiveness of the proposed method.

Cost-Benefit Analysis for the Advanced Near Net Shape Technology (ANNST) Method for Fabricating Stiffened Cylinders

NASA Technical Reports Server (NTRS)

Stoner, Mary Cecilia; Hehir, Austin R.; Ivanco, Marie L.; Domack, Marcia S.

2016-01-01

This cost-benefit analysis assesses the benefits of the Advanced Near Net Shape Technology (ANNST) manufacturing process for fabricating integrally stiffened cylinders. These preliminary, rough order-of-magnitude results report a 46 to 58 percent reduction in production costs and a 7-percent reduction in weight over the conventional metallic manufacturing technique used in this study for comparison. Production cost savings of 35 to 58 percent were reported over the composite manufacturing technique used in this study for comparison; however, the ANNST concept was heavier. In this study, the predicted return on investment of equipment required for the ANNST method was ten cryogenic tank barrels when compared with conventional metallic manufacturing. The ANNST method was compared with the conventional multi-piece metallic construction and composite processes for fabricating integrally stiffened cylinders. A case study compared these three alternatives for manufacturing a cylinder of specified geometry, with particular focus placed on production costs and process complexity, with cost analyses performed by the analogy and parametric methods. Furthermore, a scalability study was conducted for three tank diameters to assess the highest potential payoff of the ANNST process for manufacture of large-diameter cryogenic tanks. The analytical hierarchy process (AHP) was subsequently used with a group of selected subject matter experts to assess the value of the various benefits achieved by the ANNST method for potential stakeholders. The AHP study results revealed that decreased final cylinder mass and quality assurance were the most valued benefits of cylinder manufacturing methods, therefore emphasizing the relevance of the benefits achieved with the ANNST process for future projects.

A case study on implementing lean ergonomic manufacturing systems (LEMS) in an automobile industry

NASA Astrophysics Data System (ADS)

Srinivasa Rao, P.; Niraj, Malay

2016-09-01

Lean manufacturing is a business strategy developed in Japan. In the present scenario, the global market is developing new techniques for getting more and more production rate with a good quality under low cost. In this context, human factors have to be given importance to their working conditions. The study demonstrates the adoption of ergonomic conditions in lean manufacturing for the improvement of organizational performance of the industry. The aim of ergonomics is to adapt the new techniques to their work in efficient and safe ways in order to optimize the human health conditions and increasing the production rate. By conducting survey on various disciplines and showed how the production rate and human ergonomic conditions is affected.

The Impact of Technological Change on Manpower and Skill Demand: Case-Study Data and Policy Implications.

ERIC Educational Resources Information Center

Crossman, Edward R. F. W.; Laner, Stephen

To prove or disprove the hypothesis that automation and technological change impose increased skill demands on manufacturing and service industries, case studies were made of a bank and a steel and air products company, and of two oil companies, airlines, and electric power companies. The basic conceptual tool used to measure skill demands was the…

Case Study on Technical and Vocational Education in Japan. Case Studies on Technical and Vocational Education in Asia and the Pacific.

ERIC Educational Resources Information Center

Iwamoto, Muneharu

In the course of Japan's economic progress, remarkable changes have occurred in the structure of industry and employment. Workers are in extremely short supply in such occupations as mining, manufacturing and construction, services, transportation and communication, sales, and professional and technical. On the basis of recommendations of the…

An Application of Six Sigma to Reduce Supplier Quality Cost

NASA Astrophysics Data System (ADS)

Gaikwad, Lokpriya Mohanrao; Teli, Shivagond Nagappa; Majali, Vijay Shashikant; Bhushi, Umesh Mahadevappa

2016-01-01

This article presents an application of Six Sigma to reduce supplier quality cost in manufacturing industry. Although there is a wider acceptance of Six Sigma in many organizations today, there is still a lack of in-depth case study of Six Sigma. For the present research the case study methodology was used. The company decided to reduce quality cost and improve selected processes using Six Sigma methodologies. Regarding the fact that there is a lack of case studies dealing with Six Sigma especially in individual manufacturing organization this article could be of great importance also for the practitioners. This paper discusses the quality and productivity improvement in a supplier enterprise through a case study. The paper deals with an application of Six Sigma define-measure-analyze-improve-control methodology in an industry which provides a framework to identify, quantify and eliminate sources of variation in an operational process in question, to optimize the operation variables, improve and sustain performance viz. process yield with well-executed control plans. Six Sigma improves the process performance (process yield) of the critical operational process, leading to better utilization of resources, decreases variations and maintains consistent quality of the process output.

Development of Energy Models for Production Systems and Processes to Inform Environmentally Benign Decision-Making

NASA Astrophysics Data System (ADS)

Diaz-Elsayed, Nancy

Between 2008 and 2035 global energy demand is expected to grow by 53%. While most industry-level analyses of manufacturing in the United States (U.S.) have traditionally focused on high energy consumers such as the petroleum, chemical, paper, primary metal, and food sectors, the remaining sectors account for the majority of establishments in the U.S. Specifically, of the establishments participating in the Energy Information Administration's Manufacturing Energy Consumption Survey in 2006, the non-energy intensive" sectors still consumed 4*109 GJ of energy, i.e., one-quarter of the energy consumed by the manufacturing sectors, which is enough to power 98 million homes for a year. The increasing use of renewable energy sources and the introduction of energy-efficient technologies in manufacturing operations support the advancement towards a cleaner future, but having a good understanding of how the systems and processes function can reduce the environmental burden even further. To facilitate this, methods are developed to model the energy of manufacturing across three hierarchical levels: production equipment, factory operations, and industry; these methods are used to accurately assess the current state and provide effective recommendations to further reduce energy consumption. First, the energy consumption of production equipment is characterized to provide machine operators and product designers with viable methods to estimate the environmental impact of the manufacturing phase of a product. The energy model of production equipment is tested and found to have an average accuracy of 97% for a product requiring machining with a variable material removal rate profile. However, changing the use of production equipment alone will not result in an optimal solution since machines are part of a larger system. Which machines to use, how to schedule production runs while accounting for idle time, the design of the factory layout to facilitate production, and even the machining parameters --- these decisions affect how much energy is utilized during production. Therefore, at the facility level a methodology is presented for implementing priority queuing while accounting for a high product mix in a discrete event simulation environment. A baseline case is presented and alternative factory designs are suggested, which lead to energy savings of approximately 9%. At the industry level, the majority of energy consumption for manufacturing facilities is utilized for machine drive, process heating, and HVAC. Numerous studies have characterized the energy of manufacturing processes and HVAC equipment, but energy data is often limited for a facility in its entirety since manufacturing companies often lack the appropriate sensors to track it and are hesitant to release this information for confidentiality purposes. Without detailed information about the use of energy in manufacturing sites, the scope of factory studies cannot be adequately defined. Therefore, the breakdown of energy consumption of sectors with discrete production is presented, as well as a case study assessing the electrical energy consumption, greenhouse gas emissions, their associated costs, and labor costs for selected sites in the United States, Japan, Germany, China, and India. By presenting energy models and assessments of production equipment, factory operations, and industry, this dissertation provides a comprehensive assessment of energy trends in manufacturing and recommends methods that can be used beyond these case studies and industries to reduce consumption and contribute to an energy-efficient future.

Diverse task scheduling for individualized requirements in cloud manufacturing

NASA Astrophysics Data System (ADS)

Zhou, Longfei; Zhang, Lin; Zhao, Chun; Laili, Yuanjun; Xu, Lida

2018-03-01

Cloud manufacturing (CMfg) has emerged as a new manufacturing paradigm that provides ubiquitous, on-demand manufacturing services to customers through network and CMfg platforms. In CMfg system, task scheduling as an important means of finding suitable services for specific manufacturing tasks plays a key role in enhancing the system performance. Customers' requirements in CMfg are highly individualized, which leads to diverse manufacturing tasks in terms of execution flows and users' preferences. We focus on diverse manufacturing tasks and aim to address their scheduling issue in CMfg. First of all, a mathematical model of task scheduling is built based on analysis of the scheduling process in CMfg. To solve this scheduling problem, we propose a scheduling method aiming for diverse tasks, which enables each service demander to obtain desired manufacturing services. The candidate service sets are generated according to subtask directed graphs. An improved genetic algorithm is applied to searching for optimal task scheduling solutions. The effectiveness of the scheduling method proposed is verified by a case study with individualized customers' requirements. The results indicate that the proposed task scheduling method is able to achieve better performance than some usual algorithms such as simulated annealing and pattern search.

Utilization of curve offsets in additive manufacturing

NASA Astrophysics Data System (ADS)

Haseltalab, Vahid; Yaman, Ulas; Dolen, Melik

2018-05-01

Curve offsets are utilized in different fields of engineering and science. Additive manufacturing, which lately becomes an explicit requirement in manufacturing industry, utilizes curve offsets widely. One of the necessities of offsetting is for scaling which is required if there is shrinkage after the fabrication or if the surface quality of the resulting part is unacceptable. Therefore, some post-processing is indispensable. But the major application of curve offsets in additive manufacturing processes is for generating head trajectories. In a point-wise AM process, a correct tool-path in each layer can reduce lots of costs and increase the surface quality of the fabricated parts. In this study, different curve offset generation algorithms are analyzed to show their capabilities and disadvantages through some test cases and improvements on their drawbacks are suggested.

Bronchiolitis obliterans and consumer exposure to butter-flavored microwave popcorn: a case series.

PubMed

Egilman, David S; Schilling, John Henry

2012-01-01

Respiratory exposure to diacetyl and diacetyl-containing flavorings used in butter-flavored microwave popcorn (BFMP) causes lung disease, including bronchiolitis obliterans (BO), in flavorings and popcorn manufacturing workers. However, there are no published reports of lung disease among BFMP consumers. We present a case series of three BFMP consumers with biopsy-confirmed BO. We review data relating to consumer exposures, estimate case exposures, and compare them to diacetyl-containing flavoring-exposed manufacturing workers with lung disease. These consumer cases' exposure levels are comparable to those that caused disease in workers. We were unable to identify any other exposures or diseases known or suspected to cause BO in these cases. BFMP poses a significant respiratory risk to consumers. Some manufacturers have substituted diacetyl with other alpha-diketones that are likely to pose a similar risk. Simple consumer practices such as cooling the popcorn bag would eliminate the risk of severe lung disease.

Summary and recommendations. [reduced gravitational effects on materials manufactured in space

NASA Technical Reports Server (NTRS)

1975-01-01

An economic analysis using econometric and cost benefit analysis techniques was performed to determine the feasibility of space processing of certain products. The overall objectives of the analysis were (1) to determine specific products or processes uniquely connected with space manufacturing, (2) to select a specific product or process from each of the areas of semiconductors, metals, and biochemicals, and (3) to determine the overall price/cost structure of each product or process considered. The economic elements of the analysis involved a generalized decision making format for analyzing space manufacturing, a comparative cost study of the selected processes in space vs. earth manufacturing, and a supply and demand study of the economic relationships of one of the manufacturing processes. Space processing concepts were explored. The first involved the use of the shuttle as the factory with all operations performed during individual flights. The second concept involved a permanent unmanned space factory which would be launched separately. The shuttle in this case would be used only for maintenance and refurbishment. Finally, some consideration was given to a permanent manned space factory.

Cryosurgical treatment of warts: dimethyl ether and propane versus liquid nitrogen - case report and review of the literature.

PubMed

Nguyen, Nicholas V; Burkhart, Craig G

2011-10-01

For years, dermatologists have relied on cryotherapy with liquid nitrogen as a safe and effective treatment for warts. More recently, several over-the-counter (OTC) wart-freezing therapies have become available. Manufacturers have substituted liquid nitrogen with dimethyl ether and propane (DMEP), and marketed these new preparations to be safe and effective alternatives to in-office cryotherapy with liquid nitrogen. However, data from in vitro studies and comparative studies in humans refute manufacturers' claims that these products reproduce in-office cryotherapy.

21 CFR 1301.33 - Application for bulk manufacture of Schedule I and II substances.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Application for bulk manufacture of Schedule I and... manufacture of Schedule I and II substances. (a) In the case of an application for registration or reregistration to manufacture in bulk a basic class of controlled substance listed in Schedule I or II, the...

A Roadmap for the Implementation of Continued Process Verification.

PubMed

Boyer, Marcus; Gampfer, Joerg; Zamamiri, Abdel; Payne, Robin

2016-01-01

In 2014, the members of the BioPhorum Operations Group (BPOG) produced a 100-page continued process verification case study, entitled "Continued Process Verification: An Industry Position Paper with Example Protocol". This case study captures the thought processes involved in creating a continued process verification plan for a new product in response to the U.S. Food and Drug Administration's guidance on the subject introduced in 2011. In so doing, it provided the specific example of a plan developed for a new molecular antibody product based on the "A MAb Case Study" that preceded it in 2009.This document provides a roadmap that draws on the content of the continued process verification case study to provide a step-by-step guide in a more accessible form, with reference to a process map of the product life cycle. It could be used as a basis for continued process verification implementation in a number of different scenarios: For a single product and process;For a single site;To assist in the sharing of data monitoring responsibilities among sites;To assist in establishing data monitoring agreements between a customer company and a contract manufacturing organization. The U.S. Food and Drug Administration issued guidance on the management of manufacturing processes designed to improve quality and control of drug products. This involved increased focus on regular monitoring of manufacturing processes, reporting of the results, and the taking of opportunities to improve. The guidance and practice associated with it is known as continued process verification This paper summarizes good practice in responding to continued process verification guidance, gathered from subject matter experts in the biopharmaceutical industry. © PDA, Inc. 2016.

Old Dogs, New Tricks: Training Mature-Aged Manufacturing Workers

ERIC Educational Resources Information Center

Smith, Erica; Smith, Andrew; Smith, Chris Selby

2010-01-01

Purpose: This paper aims to examine the employment and training of mature-aged workers, so that suggestions for improving training for mature-aged workers may be offered. Design/methodology/approach: Six expert interviews were carried out by telephone, and three case studies involving company site visits were completed. Each company case study…

Making Total Quality Management + Just-in-Time Manufacturing Work.

ERIC Educational Resources Information Center

Waldrop, Phillip S.; Scott, Thomas E.

2000-01-01

In one case study, teamwork was implemented in mainstream production; in a second, teamwork was applied to an ad hoc project. The cases show that process technologies and management strategies such as just-in-time are not enough; selection of the appropriate mix of individuals with complementary traits is crucial. (SK)

Unraveling Appalachia's Rural Economy: The Case of a Flexible Manufacturing Network.

ERIC Educational Resources Information Center

Oberhauser, Ann M.; Pratt, Amy; Turnage, Anne-Marie

2001-01-01

The growing importance of multiple-income strategies in the changing rural Appalachian economy is discussed via a case study of a network of female home-based machine-knitters. Social networks are an important part of the knitters' recruitment and training process, promote leadership development, and help overcome some of women's economic…

National outbreak of Salmonella Give linked to a local food manufacturer in Malta, October 2016.

PubMed

Donachie, A; Melillo, T; Bubba, L; Hartman, H; Borg, M-L

2018-06-26

Salmonella Give is a rare serotype across Europe. In October 2016, a national outbreak of S. Give occurred in Malta. We describe the epidemiological, environmental, microbiological and veterinary investigations. Whole-genome sequencing (WGS) was performed on human, food, environmental and veterinary isolates. Thirty-six human cases were reported between October and November 2016, 10 (28%) of whom required hospitalisation. Twenty-six (72%) cases were linked to four restaurants. S. Give was isolated from ready-to-eat antipasti served by three restaurants which were all supplied by the same local food manufacturer. Food-trace-back investigations identified S. Give in packaged bean dips, ham, pork and an asymptomatic food handler at the manufacturer; inspections found inadequate separation between raw and ready-to-eat food during processing. WGS indicated two genetically distinguishable strains of S. Give with two distinct clusters identified; one cluster linked to the local food manufacturer and a second linked to veterinary samples. Epidemiological, environmental and WGS evidence pointed towards cross-contamination of raw and ready-to-eat foods at the local manufacturer as the likely source of one cluster. Severity of illness indicates a high virulence of this specific serotype. To prevent future cases and outbreaks, adherence to food safety practices at manufacturing level need to be reinforced.

Environmental and Economic Implications of Distributed Additive Manufacturing: The Case of Injection Mold Tooling: Environmental Implications of Additive Manufacturing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Runze; Riddle, Matthew E.; Graziano, Diane

Additive manufacturing (AM) holds great potentials in enabling superior engineering functionality, streamlining supply chains, and reducing life cycle impacts compared to conventional manufacturing (CM). This study estimates the net changes in supply-chain lead time, life cycle primary energy consumption, greenhouse gas (GHG) emissions, and life cycle costs (LCC) associated with AM technologies for the case of injection molding, to shed light on the environmental and economic advantages of a shift from international or onshore CM to AM in the United States. A systems modeling framework is developed, with integrations of lead-time analysis, life cycle inventory analysis, LCC model, and scenariosmore » considering design differences, supply-chain options, productions, maintenance, and AM technological developments. AM yields a reduction potential of 3% to 5% primary energy, 4% to 7% GHG emissions, 12% to 60% lead time, and 15% to 35% cost over 1 million cycles of the injection molding production depending on the AM technology advancement in future. The economic advantages indicate the significant role of AM technology in raising global manufacturing competitiveness of local producers, while the relatively small environmental benefits highlight the necessity of considering trade-offs and balance techniques between environmental and economic performances when AM is adopted in the tooling industry. The results also help pinpoint the technological innovations in AM that could lead to broader benefits in future.« less

Environmental and Economic Implications of Distributed Additive Manufacturing: The Case of Injection Mold Tooling: Environmental Implications of Additive Manufacturing

DOE PAGES

Huang, Runze; Riddle, Matthew E.; Graziano, Diane; ...

2017-08-26

Additive manufacturing (AM) holds great potentials in enabling superior engineering functionality, streamlining supply chains, and reducing life cycle impacts compared to conventional manufacturing (CM). This study estimates the net changes in supply-chain lead time, life cycle primary energy consumption, greenhouse gas (GHG) emissions, and life cycle costs (LCC) associated with AM technologies for the case of injection molding, to shed light on the environmental and economic advantages of a shift from international or onshore CM to AM in the United States. A systems modeling framework is developed, with integrations of lead-time analysis, life cycle inventory analysis, LCC model, and scenariosmore » considering design differences, supply-chain options, productions, maintenance, and AM technological developments. AM yields a reduction potential of 3% to 5% primary energy, 4% to 7% GHG emissions, 12% to 60% lead time, and 15% to 35% cost over 1 million cycles of the injection molding production depending on the AM technology advancement in future. The economic advantages indicate the significant role of AM technology in raising global manufacturing competitiveness of local producers, while the relatively small environmental benefits highlight the necessity of considering trade-offs and balance techniques between environmental and economic performances when AM is adopted in the tooling industry. The results also help pinpoint the technological innovations in AM that could lead to broader benefits in future.« less

A low cost technique to evaluate usable product for small manufacturing companies: a case study on Garcia robot.

PubMed

An, Vatana; Soares, Marcelo

2012-01-01

A usability evaluation technique to evaluate user interfaces is introduces. The technique is effective and affordable for small manufacturing companies. By using this technique, an integration of users' feedbacks and some usability concepts, a product can be 3 times easier to use among potential users and more than 5 times easier to use among motivated users. In addition, the technique can be implemented with the company's employees as participants.

Fabrication of a Cranial Prosthesis Combined with an Ocular Prosthesis Using Rapid Prototyping: A Case Report.

PubMed

Shankaran, Gayatri; Deogade, Suryakant Chhagan; Dhirawani, Rajesh

2016-01-01

Rapid prototyping (RP) is a technique of manufacturing parts by the additive layer manufacturing technology; where, a three-dimensional (3D) model created in a computer aided design (CAD) system is sectioned into 2D profiles, which are further constructed by RP layer by layer. Its use is not limited to industrial or engineering fields and has extended to the medical field for the manufacturing of custom implants and prostheses, the study of anatomy and surgical planning. Nowadays, dentists are more frequently encountered with the individuals affected with craniofacial defects due to trauma. In such cases, the craniomaxillofacial rehabilitation is a real challenge to bring the patients back to society and promote their well-being. The conventional impression technique for facial prosthesis fabrication has the disadvantage of deforming the soft tissue and causing discomfort for the patient. Herein, we describe the fabrication of a cranial prosthesis combined with an ocular prosthesis with RP and stereolithography.

Fabrication of a Cranial Prosthesis Combined with an Ocular Prosthesis Using Rapid Prototyping: A Case Report

PubMed Central

Shankaran, Gayatri; Dhirawani, Rajesh

2016-01-01

Rapid prototyping (RP) is a technique of manufacturing parts by the additive layer manufacturing technology; where, a three-dimensional (3D) model created in a computer aided design (CAD) system is sectioned into 2D profiles, which are further constructed by RP layer by layer. Its use is not limited to industrial or engineering fields and has extended to the medical field for the manufacturing of custom implants and prostheses, the study of anatomy and surgical planning. Nowadays, dentists are more frequently encountered with the individuals affected with craniofacial defects due to trauma. In such cases, the craniomaxillofacial rehabilitation is a real challenge to bring the patients back to society and promote their well-being. The conventional impression technique for facial prosthesis fabrication has the disadvantage of deforming the soft tissue and causing discomfort for the patient. Herein, we describe the fabrication of a cranial prosthesis combined with an ocular prosthesis with RP and stereolithography. PMID:27536331

26 CFR 48.6416(b)(3)-3 - Supporting evidence required in case of tax-paid articles used for further manufacture.

Code of Federal Regulations, 2010 CFR

2010-04-01

... articles used for further manufacture. 48.6416(b)(3)-3 Section 48.6416(b)(3)-3 Internal Revenue INTERNAL... manufacture. (a) Evidence to be submitted by claimant. No claim for credit or refund of an overpayment, within... of payment, (5) Indicating that the article was used by the claimant as material in the manufacture...

Some results of hemosorption columns development and usage in Czechoslovakia.

PubMed

Kálal, J; Tlustáková, M

Hemoperfusion columns packed with active charcoal and a synthetic resin have been manufactured in Czechoslovakia since 1983. In both cases the sorption packings are coated with a layer of poly(2-hydroxyethyl methacrylate). The columns are manufactured in two sizes: for adults (800 ml) and for children (400 ml). The manufacturer is OPS Kolín: the number of columns manufactured so far is 3400.

UV-CURED FINISHING WORKS FOR LANE

EPA Science Inventory

The Midwest Research Institute, under a cooperative agreement with the U.S. EPA, conducted a study to identify wood furniture manufacturing facilities that had converted to low-VOC/HAP wood furniture coatings and to develop case studies for those facilities. This article addresse...

27 CFR 53.142 - Denial, revocation or suspension of registration.

Code of Federal Regulations, 2010 CFR

2010-04-01

... TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY (CONTINUED) FIREARMS MANUFACTURERS EXCISE TAXES... tax free under section 4221 of the Code in any case in which he finds that: (1) The registrant is not a bona fide manufacturer, or a purchaser reselling direct to manufacturers or exporters; (2) The...

MapReduce Based Parallel Bayesian Network for Manufacturing Quality Control

NASA Astrophysics Data System (ADS)

Zheng, Mao-Kuan; Ming, Xin-Guo; Zhang, Xian-Yu; Li, Guo-Ming

2017-09-01

Increasing complexity of industrial products and manufacturing processes have challenged conventional statistics based quality management approaches in the circumstances of dynamic production. A Bayesian network and big data analytics integrated approach for manufacturing process quality analysis and control is proposed. Based on Hadoop distributed architecture and MapReduce parallel computing model, big volume and variety quality related data generated during the manufacturing process could be dealt with. Artificial intelligent algorithms, including Bayesian network learning, classification and reasoning, are embedded into the Reduce process. Relying on the ability of the Bayesian network in dealing with dynamic and uncertain problem and the parallel computing power of MapReduce, Bayesian network of impact factors on quality are built based on prior probability distribution and modified with posterior probability distribution. A case study on hull segment manufacturing precision management for ship and offshore platform building shows that computing speed accelerates almost directly proportionally to the increase of computing nodes. It is also proved that the proposed model is feasible for locating and reasoning of root causes, forecasting of manufacturing outcome, and intelligent decision for precision problem solving. The integration of bigdata analytics and BN method offers a whole new perspective in manufacturing quality control.

Optimizing the construction of devices to control inaccesible surfaces - case study

NASA Astrophysics Data System (ADS)

Niţu, E. L.; Costea, A.; Iordache, M. D.; Rizea, A. D.; Babă, Al

2017-10-01

The modern concept for the evolution of manufacturing systems requires multi-criteria optimization of technological processes and equipments, prioritizing associated criteria according to their importance. Technological preparation of the manufacturing can be developed, depending on the volume of production, to the limit of favourable economical effects related to the recovery of the costs for the design and execution of the technological equipment. Devices, as subsystems of the technological system, in the general context of modernization and diversification of machines, tools, semi-finished products and drives, are made in a multitude of constructive variants, which in many cases do not allow their identification, study and improvement. This paper presents a case study in which the multi-criteria analysis of some structures, based on a general optimization method, of novelty character, is used in order to determine the optimal construction variant of a control device. The rational construction of the control device confirms that the optimization method and the proposed calculation methods are correct and determine a different system configuration, new features and functions, and a specific method of working to control inaccessible surfaces.

Retailer Stackelberg game in a supply chain with pricing and service decisions and simple price discount contract.

PubMed

Sadjadi, Seyed Jafar; Asadi, Hashem; Sadeghian, Ramin; Sahebi, Hadi

2018-01-01

This paper studies the Retailer Stackelberg game in a supply chain consisting of two manufacturers and one retailer where they compete simultaneously under three factors including price, service and simple price discount contract. It is assumed that the second manufacturer provides service directly to his customers, and the retailer provides service for the first product's customers, while the retailer buys the first product under price discount from the first manufacturer. The analysis of the optimal equilibrium solutions and the results of the numerical examples show that if a manufacturer chooses the appropriate range of discount rate, he will gain more profit than when there is no discount given to the retailer. This situation can be considered as an effective tool for the coordination of the first manufacturer and the retailer to offer discount by manufacturer and to provide the service by the retailer. We obtain equilibrium solution of Retailer Stackelberg game and analyze the numerical examples under two cases: a) the manufacturers sell their products to the retailer without price discount contract. b) The first manufacturer sells his products to the retailer with the simple price discount contract. The preliminary results show that the service and the price discount contract can improve the performance of supply chain.

Retailer Stackelberg game in a supply chain with pricing and service decisions and simple price discount contract

PubMed Central

Sadjadi, Seyed Jafar; Sadeghian, Ramin; Sahebi, Hadi

2018-01-01

This paper studies the Retailer Stackelberg game in a supply chain consisting of two manufacturers and one retailer where they compete simultaneously under three factors including price, service and simple price discount contract. It is assumed that the second manufacturer provides service directly to his customers, and the retailer provides service for the first product’s customers, while the retailer buys the first product under price discount from the first manufacturer. The analysis of the optimal equilibrium solutions and the results of the numerical examples show that if a manufacturer chooses the appropriate range of discount rate, he will gain more profit than when there is no discount given to the retailer. This situation can be considered as an effective tool for the coordination of the first manufacturer and the retailer to offer discount by manufacturer and to provide the service by the retailer. We obtain equilibrium solution of Retailer Stackelberg game and analyze the numerical examples under two cases: a) the manufacturers sell their products to the retailer without price discount contract. b) The first manufacturer sells his products to the retailer with the simple price discount contract. The preliminary results show that the service and the price discount contract can improve the performance of supply chain. PMID:29649315

A New Approach to Integrate Internet-of-Things and Software-as-a-Service Model for Logistic Systems: A Case Study

PubMed Central

Chen, Shang-Liang; Chen, Yun-Yao; Hsu, Chiang

2014-01-01

Cloud computing is changing the ways software is developed and managed in enterprises, which is changing the way of doing business in that dynamically scalable and virtualized resources are regarded as services over the Internet. Traditional manufacturing systems such as supply chain management (SCM), customer relationship management (CRM), and enterprise resource planning (ERP) are often developed case by case. However, effective collaboration between different systems, platforms, programming languages, and interfaces has been suggested by researchers. In cloud-computing-based systems, distributed resources are encapsulated into cloud services and centrally managed, which allows high automation, flexibility, fast provision, and ease of integration at low cost. The integration between physical resources and cloud services can be improved by combining Internet of things (IoT) technology and Software-as-a-Service (SaaS) technology. This study proposes a new approach for developing cloud-based manufacturing systems based on a four-layer SaaS model. There are three main contributions of this paper: (1) enterprises can develop their own cloud-based logistic management information systems based on the approach proposed in this paper; (2) a case study based on literature reviews with experimental results is proposed to verify that the system performance is remarkable; (3) challenges encountered and feedback collected from T Company in the case study are discussed in this paper for the purpose of enterprise deployment. PMID:24686728

A new approach to integrate Internet-of-things and software-as-a-service model for logistic systems: a case study.

PubMed

Chen, Shang-Liang; Chen, Yun-Yao; Hsu, Chiang

2014-03-28

Cloud computing is changing the ways software is developed and managed in enterprises, which is changing the way of doing business in that dynamically scalable and virtualized resources are regarded as services over the Internet. Traditional manufacturing systems such as supply chain management (SCM), customer relationship management (CRM), and enterprise resource planning (ERP) are often developed case by case. However, effective collaboration between different systems, platforms, programming languages, and interfaces has been suggested by researchers. In cloud-computing-based systems, distributed resources are encapsulated into cloud services and centrally managed, which allows high automation, flexibility, fast provision, and ease of integration at low cost. The integration between physical resources and cloud services can be improved by combining Internet of things (IoT) technology and Software-as-a-Service (SaaS) technology. This study proposes a new approach for developing cloud-based manufacturing systems based on a four-layer SaaS model. There are three main contributions of this paper: (1) enterprises can develop their own cloud-based logistic management information systems based on the approach proposed in this paper; (2) a case study based on literature reviews with experimental results is proposed to verify that the system performance is remarkable; (3) challenges encountered and feedback collected from T Company in the case study are discussed in this paper for the purpose of enterprise deployment.

Yacht-maker's lung: A case of hypersensitivity pneumonitis in yacht manufacturing.

PubMed

Volkman, Kristen K; Merrick, James G; Zacharisen, Michael C

2006-10-01

We present a case of hypersensitivity pneumonitis in a 46-year-old female working at a yacht manufacturing company. She reported a 2-month history of progressive dyspnea, chest tightness, and daytime, nocturnal, and exertional cough in temporal relationship to work where she was exposed to chemicals involved in the manufacture of yachts. Treatment with systemic antibiotic therapy, inhaled bronchodilators, and inhaled corticosteroids provided minimal relief of symptoms. Spirometry revealed a restrictive defect and a chest x-ray demonstrated a diffuse interstitial pattern. She improved on oral corticosteroids and with avoidance of her work environment had resolution of her symptoms and normalization of her spirometry. Among the various chemicals the patient was exposed to, the most likely causative agents for her symptoms were dimethyl phthalate and styrene. Although the specific chemical or antigen could not be determined, the history and objective findings are consistent with occupational hypersensitivity pneumonitis. This represents a case of hypersensitivity pneumonitis related to the manufacture of yachts.

International outbreak of Salmonella Eastbourne infection traced to contaminated chocolate.

PubMed

Craven, P C; Mackel, D C; Baine, W B; Barker, W H; Gangarosa, E J

1975-04-05

Between Dec. 4, 1973, and Feb. 15, 1974, 80 cases of infection due to Salmonella eastbourne, previously a rare isolated serotype in the United States, were reported from twenty-three States. An additional 39 cases were reported from seven Provinces in Canada during a similar period. A telephone case-control study implicated Christmas-wrapped chocolate balls manufactured by a Canadian company as the vehicle of transmission. S. eastbourne was subsequently isolated from several samples of leftover chocolate balls obtained from homes where cases occurred. Investigation of the factory revealed that the contaminated Christmas and Easter chocolates, and a few chocolate items for year-round sale, had been produced between May and October, 1973. Bacteriological testing of samples taken at the plant implicated cocoa beans as the probable source of the salmonella organisms which, in the low-moisture chocolate, were able to survive heating during production. This outbreak and the finding of salmonella of other serotypes in chocolates produced by another manufacturer suggest that chocolate-related salmonellosis may be a significant public-health problem.

The Development of Technical and Vocational Education in Malaysia--A Case Study in Quality Improvement. Case Studies on Technical and Vocational Education in Asia and the Pacific.

ERIC Educational Resources Information Center

Hee, Tieng Fok

The economic profile of Malaysia has changed from an economy mainly based on agriculture and the production of tin ore to a more balanced economy with continuing growth in the manufacturing and industrial sectors. Educational programs need to be upgraded and improved, particularly the direction and development of technical and vocational education…

CASE STUDIES: LOW-VOC/HAP WOOD FURNITURE COATINGS

EPA Science Inventory

The report gives results of a study in which wood furniture manufacturing facilities were identified that had converted at least one of their primary coating steps to low-volatile organic compound (VOC)/hazardous Air pollutant (HAP) wood furniture coatings: high-solids, water...

Asbestos related diseases among workers of asbestos processing plants in relation to type of production and asbestos use.

PubMed

Szeszenia-Dąbrowska, Neonila; Świątkowska, Beata; Sobala, Wojciech; Szubert, Zuzanna; Wilczyńska, Urszula

2015-01-01

Asbestos dust is one of the most dangerous pneumoconiotic and carcinogenic agents. The aim of this study was to assess the occurrence of asbestosis and pleural mesothelioma, depending on asbestos consumption and the type of manufactured products, among former asbestos workers in Poland. The study subjects included employees of 18 large state-owned asbestos processing enterprises operating in the Polish market in 1945-1998. The study is based on data obtained from asbestos company records and the Central Register of Occupational Diseases data on the cases of asbestosis and mesothelioma for the period from 1970 till 2012 as well as data from Amiantus Programme. The analysis was performed for 5 sectors comprising plants classified according to the products manufactured and applied production technology. In the study period, 2160 cases of asbestosis and 138 cases of mesothelioma were reported. The plants processed a total of about 2 million tons of asbestos, including about 7.5% of crocidolite. Total asbestosis consumption was a strong predictor of the rate of asbestosis incidence (R2 = 0.68, p = 0.055). The highest risk occurrence of asbestosis was observed in the production of textiles and sealing products. Mesothelioma occurred only in plants where crocidolite had been ever processed. Total asbestos consumption was a strong predictor of the rate of asbestosis incidence. The observation confirms the relationship between exposure to crocidolite and the occurrence of mesothelioma, regardless of the manufactured products, and suggests the absence of such a link for the total volume of asbestos consumption.

Q-marker based strategy for CMC research of Chinese medicine: A case study of Panax Notoginseng saponins.

PubMed

Zhong, Yi; Zhu, Jieqiang; Yang, Zhenzhong; Shao, Qing; Fan, Xiaohui; Cheng, Yiyu

2018-01-31

To ensure pharmaceutical quality, chemistry, manufacturing and control (CMC) research is essential. However, due to the inherent complexity of Chinese medicine (CM), CMC study of CM remains a great challenge for academia, industry, and regulatory agencies. Recently, quality-marker (Q-marker) was proposed to establish quality standards or quality analysis approaches of Chinese medicine, which sheds a light on Chinese medicine's CMC study. Here manufacture processes of Panax Notoginseng Saponins (PNS) is taken as a case study and the present work is to establish a Q-marker based research strategy for CMC of Chinese medicine. The Q-markers of Panax Notoginseng Saponins (PNS) is selected and established by integrating chemical profile with pharmacological activities. Then, the key processes of PNS manufacturing are identified by material flow analysis. Furthermore, modeling algorithms are employed to explore the relationship between Q-markers and critical process parameters (CPPs) of the key processes. At last, CPPs of the key processes are optimized in order to improving the process efficiency. Among the 97 identified compounds, Notoginsenoside R 1 , ginsenoside Rg 1 , Re, Rb 1 and Rd are selected as the Q-markers of PNS. Our analysis on PNS manufacturing show the extraction process and column chromatography process are the key processes. With the CPPs of each process as the inputs and Q-markers' contents as the outputs, two process prediction models are built separately for the extraction process and column chromatography process of Panax notoginseng, which both possess good prediction ability. Based on the efficiency models of extraction process and column chromatography process we constructed, the optimal CPPs of both processes are calculated. Our results show that the Q-markers derived from CMC research strategy can be applied to analyze the manufacturing processes of Chinese medicine to assure product's quality and promote key processes' efficiency simultaneously. Copyright © 2018 Elsevier GmbH. All rights reserved.

ENVIRONMENTAL RESEARCH BRIEF: POLLUTION PREVENTION ASSESSMENT FOR A MANUFACTURER OF GEAR CASES FOR OUTBOARD MOTORS

EPA Science Inventory

The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small and medium-size manufacturers who want to minimize their generation of waste but who lack the expertise to do so. n an effort to assist these manufacturers Waste Minimization Assessment Cent...

49 CFR 325.37 - Location and operation of sound level measurement system; highway operations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... recommendation of the manufacturer of the sound level measurement system. (2) In no case shall the holder or... angle that is consistent with the recommendation of the system's manufacturer. If the manufacturer of... system; highway operations. 325.37 Section 325.37 Transportation Other Regulations Relating to...

Snap-lock bags with red band: A study of manufacturing characteristics, thermal and chemical properties.

PubMed

Sim, Yvonne Hui Ying; Koh, Alaric C W; Lim, Shing Min; Yew, Sok Yee

2015-10-01

Drug packaging is commonly submitted to the Forensic Chemistry and Physics Laboratory of the Health Sciences Authority, Singapore, for examination. The drugs seized are often packaged in plastic bags. These bags are examined for linkages to provide law enforcement with useful associations between the traffickers and drug abusers. The plastic bags submitted may include snap-lock bags, some with a red band located above the snap-lock closure and some without. Current techniques for examination involve looking at the physical characteristics (dimensions, thickness and polarising patterns) and manufacturing marks of these bags. In cases where manufacturing marks on the main body of the bags are poor or absent, the manufacturing characteristics present on the red band can be examined. A study involving approximately 1000 bags was conducted to better understand the variations in the manufacturing characteristics of the red band. This understanding is crucial in helping to determine associations/eliminations between bags. Two instrumental techniques, namely differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FT-IR) were explored to evaluate the effectiveness of examining the chemical composition to discriminate the bags. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Properties of various silicon oxide phases in thin films

NASA Technical Reports Server (NTRS)

Ritter, E.

1980-01-01

Layers of SiO2 with reproducible properties can be manufactured relatively easily today. In the case of SiO and Si2O3 layers, it is necessary to carefully check all of the manufacturing parameters for producing layers with reproducible properties. The properties of the layers in the case of SiO2 do conform to expectations. In the case of Si2O3 and SiO, they can be understood at least qualitatively. Additional interesting models are available for a quantitative understanding.

Relationship between industrial discharges and contamination of raw water resources by perfluorinated compounds: part II: Case study of a fluorotelomer polymer manufacturing plant.

PubMed

Dauchy, Xavier; Boiteux, Virginie; Rosin, Christophe; Munoz, Jean-François

2012-09-01

In this study, the concentrations of 10 perfluorinated compounds (PFCs) were measured in effluents of a fluorotelomer polymer manufacturing plant and its wastewater treatment plant. A 50-fold increase between the two effluents mass flows was observed. The water quality of two drinking water treatment plants located downstream at 15 and 25 km from the manufacturing plant was examined. An increase of the sum of PFCs was observed between the river (30 ng/L) and an alluvial well (70 ng/L), and between the raw water (9 ng/L) and the outlet of a biological treatment (97 ng/L). These results indicate a possible degradation of fluorotelomers, occurring during wastewater treatment, sediment infiltration in the alluvial aquifer, and drinking water treatment.

Special Feature: Epistemological Paradigms in Evaluation: Implications for Practice. Section 1: "Paradigm Contrast" Case Studies.

ERIC Educational Resources Information Center

Rose, Tom; And Others

1991-01-01

This section presents two pragmatic studies focusing on a real-life situation and specific applications in managerial decision making. One study deals with improving occupational safety in a bedding manufacturing plant, whereas the other concentrates on managing a state mental health program. (SLD)

Towards Additive Manufacture of Functional, Spline-Based Morphometric Models of Healthy and Diseased Coronary Arteries: In Vitro Proof-of-Concept Using a Porcine Template.

PubMed

Jewkes, Rachel; Burton, Hanna E; Espino, Daniel M

2018-02-02

The aim of this study is to assess the additive manufacture of morphometric models of healthy and diseased coronary arteries. Using a dissected porcine coronary artery, a model was developed with the use of computer aided engineering, with splines used to design arteries in health and disease. The model was altered to demonstrate four cases of stenosis displaying varying severity, based on published morphometric data available. Both an Objet Eden 250 printer and a Solidscape 3Z Pro printer were used in this analysis. A wax printed model was set into a flexible thermoplastic and was valuable for experimental testing with helical flow patterns observed in healthy models, dominating the distal LAD (left anterior descending) and left circumflex arteries. Recirculation zones were detected in all models, but were visibly larger in the stenosed cases. Resin models provide useful analytical tools for understanding the spatial relationships of blood vessels, and could be applied to preoperative planning techniques, but were not suitable for physical testing. In conclusion, it is feasible to develop blood vessel models enabling experimental work; further, through additive manufacture of bio-compatible materials, there is the possibility of manufacturing customized replacement arteries.

Towards Additive Manufacture of Functional, Spline-Based Morphometric Models of Healthy and Diseased Coronary Arteries: In Vitro Proof-of-Concept Using a Porcine Template

PubMed Central

Jewkes, Rachel; Burton, Hanna E.; Espino, Daniel M.

2018-01-01

The aim of this study is to assess the additive manufacture of morphometric models of healthy and diseased coronary arteries. Using a dissected porcine coronary artery, a model was developed with the use of computer aided engineering, with splines used to design arteries in health and disease. The model was altered to demonstrate four cases of stenosis displaying varying severity, based on published morphometric data available. Both an Objet Eden 250 printer and a Solidscape 3Z Pro printer were used in this analysis. A wax printed model was set into a flexible thermoplastic and was valuable for experimental testing with helical flow patterns observed in healthy models, dominating the distal LAD (left anterior descending) and left circumflex arteries. Recirculation zones were detected in all models, but were visibly larger in the stenosed cases. Resin models provide useful analytical tools for understanding the spatial relationships of blood vessels, and could be applied to preoperative planning techniques, but were not suitable for physical testing. In conclusion, it is feasible to develop blood vessel models enabling experimental work; further, through additive manufacture of bio-compatible materials, there is the possibility of manufacturing customized replacement arteries. PMID:29393899

Research on rebuilding the data information environment for aeronautical manufacturing enterprise

NASA Astrophysics Data System (ADS)

Feng, Xilan; Jiang, Zhiqiang; Zong, Xuewen; Shi, Jinfa

2005-12-01

The data environment on integrated information system and the basic standard on information resource management are the key effectively of the remote collaborative designing and manufacturing for complex product. A study project on rebuilding the data information environment for aeronautical manufacturing enterprise (Aero-ME) is put forwarded. Firstly, the data environment on integrated information system, the basic standard on information resource management, the basic establishment on corporation's information, the development on integrated information system, and the information education are discussed profoundly based on the practical requirement of information resource and technique for contemporary Aero-ME. Then, the idea and method with the data environment rebuilding based on I-CASE in the corporation is put forward, and the effective method and implement approach for manufacturing enterprise information is brought forwards. It will also the foundation and assurance that rebuilding the corporation data-environment and promoting standardizing information resource management for the development of Aero-ME information engineering.

New Whole-House Solutions Case Study: Technology Solutions for New Manufactured Homes, Idaho, Oregon, and Washington

DOE Office of Scientific and Technical Information (OSTI.GOV)

BA-PIRC

2013-11-01

The Building America Partnership for Improved Residential Construction, the Bonneville Power Administration (BPA), and Northwest Energy Works (NEW), the current Northwest Energy Efficient Manufactured Housing Program (NEEM) administrator, have been collaborating to conduct research on new specifications that would improve on the energy requirements of a NEEM home. In its role as administrator, NEW administers the technical specs, performs research and engineering analysis, implements ongoing construction quality management procedures, and maintains a central database with home tracking. This project prototyped and assessed the performances of cost-effective high performance building assemblies and mechanical systems that are not commonly deployed in themore » manufacturing setting. The package of measures is able to reduce energy used for space conditioning, water heating and lighting by 50 percent over typical manufactured homes produced in the northwest.« less

A statistical approach to nuclear fuel design and performance

NASA Astrophysics Data System (ADS)

Cunning, Travis Andrew

As CANDU fuel failures can have significant economic and operational consequences on the Canadian nuclear power industry, it is essential that factors impacting fuel performance are adequately understood. Current industrial practice relies on deterministic safety analysis and the highly conservative "limit of operating envelope" approach, where all parameters are assumed to be at their limits simultaneously. This results in a conservative prediction of event consequences with little consideration given to the high quality and precision of current manufacturing processes. This study employs a novel approach to the prediction of CANDU fuel reliability. Probability distributions are fitted to actual fuel manufacturing datasets provided by Cameco Fuel Manufacturing, Inc. They are used to form input for two industry-standard fuel performance codes: ELESTRES for the steady-state case and ELOCA for the transient case---a hypothesized 80% reactor outlet header break loss of coolant accident. Using a Monte Carlo technique for input generation, 105 independent trials are conducted and probability distributions are fitted to key model output quantities. Comparing model output against recognized industrial acceptance criteria, no fuel failures are predicted for either case. Output distributions are well removed from failure limit values, implying that margin exists in current fuel manufacturing and design. To validate the results and attempt to reduce the simulation burden of the methodology, two dimensional reduction methods are assessed. Using just 36 trials, both methods are able to produce output distributions that agree strongly with those obtained via the brute-force Monte Carlo method, often to a relative discrepancy of less than 0.3% when predicting the first statistical moment, and a relative discrepancy of less than 5% when predicting the second statistical moment. In terms of global sensitivity, pellet density proves to have the greatest impact on fuel performance, with an average sensitivity index of 48.93% on key output quantities. Pellet grain size and dish depth are also significant contributors, at 31.53% and 13.46%, respectively. A traditional limit of operating envelope case is also evaluated. This case produces output values that exceed the maximum values observed during the 105 Monte Carlo trials for all output quantities of interest. In many cases the difference between the predictions of the two methods is very prominent, and the highly conservative nature of the deterministic approach is demonstrated. A reliability analysis of CANDU fuel manufacturing parametric data, specifically pertaining to the quantification of fuel performance margins, has not been conducted previously. Key Words: CANDU, nuclear fuel, Cameco, fuel manufacturing, fuel modelling, fuel performance, fuel reliability, ELESTRES, ELOCA, dimensional reduction methods, global sensitivity analysis, deterministic safety analysis, probabilistic safety analysis.

A sustainable manufacturing system design: A fuzzy multi-objective optimization model.

PubMed

Nujoom, Reda; Mohammed, Ahmed; Wang, Qian

2017-08-10

In the past decade, there has been a growing concern about the environmental protection in public society as governments almost all over the world have initiated certain rules and regulations to promote energy saving and minimize the production of carbon dioxide (CO 2 ) emissions in many manufacturing industries. The development of sustainable manufacturing systems is considered as one of the effective solutions to minimize the environmental impact. Lean approach is also considered as a proper method for achieving sustainability as it can reduce manufacturing wastes and increase the system efficiency and productivity. However, the lean approach does not include environmental waste of such as energy consumption and CO 2 emissions when designing a lean manufacturing system. This paper addresses these issues by evaluating a sustainable manufacturing system design considering a measurement of energy consumption and CO 2 emissions using different sources of energy (oil as direct energy source to generate thermal energy and oil or solar as indirect energy source to generate electricity). To this aim, a multi-objective mathematical model is developed incorporating the economic and ecological constraints aimed for minimization of the total cost, energy consumption, and CO 2 emissions for a manufacturing system design. For the real world scenario, the uncertainty in a number of input parameters was handled through the development of a fuzzy multi-objective model. The study also addresses decision-making in the number of machines, the number of air-conditioning units, and the number of bulbs involved in each process of a manufacturing system in conjunction with a quantity of material flow for processed products. A real case study was used for examining the validation and applicability of the developed sustainable manufacturing system model using the fuzzy multi-objective approach.

The Impact of Industrial Relocation on Displaced Workers: A Case Study of Cortland, NY.

ERIC Educational Resources Information Center

Beneria, Lourdes

1998-01-01

This report examines a typical case of a small town within a predominantly rural county losing its largest employer of many years. During 1992-95, over 850 workers were laid off in Cortland, New York, as Smith-Corona Corporation transferred its manufacturing operations from Cortland to Tijuana, Mexico. Interviews with laid-off workers, conducted…

49 CFR 529.1 - Scope and purpose.

Code of Federal Regulations, 2013 CFR

2013-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION MANUFACTURERS OF MULTISTAGE AUTOMOBILES § 529.1 Scope and purpose. This part determines, in cases where more than one person is the manufacturer of an automobile, which...

49 CFR 529.1 - Scope and purpose.

Code of Federal Regulations, 2012 CFR

2012-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION MANUFACTURERS OF MULTISTAGE AUTOMOBILES § 529.1 Scope and purpose. This part determines, in cases where more than one person is the manufacturer of an automobile, which...

49 CFR 529.1 - Scope and purpose.

Code of Federal Regulations, 2014 CFR

2014-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION MANUFACTURERS OF MULTISTAGE AUTOMOBILES § 529.1 Scope and purpose. This part determines, in cases where more than one person is the manufacturer of an automobile, which...

49 CFR 529.1 - Scope and purpose.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION MANUFACTURERS OF MULTISTAGE AUTOMOBILES § 529.1 Scope and purpose. This part determines, in cases where more than one person is the manufacturer of an automobile, which...

49 CFR 529.1 - Scope and purpose.

Code of Federal Regulations, 2011 CFR

2011-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION MANUFACTURERS OF MULTISTAGE AUTOMOBILES § 529.1 Scope and purpose. This part determines, in cases where more than one person is the manufacturer of an automobile, which...

Sugar cane manufacturing is associated with tuberculosis in an indigenous population in Brazil.

PubMed

Sacchi, Flávia Patussi Correia; Croda, Mariana Garcia; Estevan, Anderson Oliveira; Ko, Albert I; Croda, Julio

2013-03-01

Tuberculosis (TB) remains one of the leading causes of morbidity and mortality among indigenous peoples in Brazil, and identifying the risk factors for TB in this population secondary to specific epidemiological conditions is essential for recommending interventions aimed at disease control. This case-control study was conducted with an indigenous population between June 2009 and August 2011 in Dourados, Brazil. Tuberculosis cases reported to the national disease surveillance programme were paired with two control cases matched by age and geographic location. There were 63 cases included in this study, and the annual incidence of TB in the indigenous communities examined was 222 (95% CI, 148-321) per 100 000 inhabitants. The multivariate analysis demonstrated that the variables associated with TB infection included male gender (OR 2.6; 95% CI 1.3-5.3), not owning a home (OR 3.4; 95% CI 1.2-10.1), illiteracy (OR 2.4; 95% CI 1.1-5.0), TB contact (OR 2.4; 95% CI 1.2-4.8) and work performed in a sugar cane factory (OR 6.8; 95% CI 1.2-36.9). There is a potential relationship between exposure to sugar cane manufacturing processes and tuberculosis infection among indigenous populations.

Fiberglass distribution poles: A case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, M.F.; Hosford, G.S.; Boozer, J.F. III

1995-01-01

This paper addresses the design considerations and manufacturing techniques along with mechanical test results of fiberglass reinforced composite (FRC) primary distribution poles. With it`s light weight, and virtually no maintenance it offers a viable alternative for use in remote and inaccessible locations. This paper also discusses a case study where seventy five FRC primary distribution poles have been installed on a distribution system in a remote area accessible only by foot and helicopter.

Long-term health experience of jet engine manufacturing workers: V. Issues with the analysis of non-malignant central nervous system neoplasms.

PubMed

Buchanich, Jeanine M; Youk, Ada O; Marsh, Gary M; Kennedy, Kathleen J; Lacey, Steven E; Hancock, Roger P; Esmen, Nurtan A; Cunningham, Michael A; Leiberman, Frank S; Fleissner, Mary Lou

2011-01-01

We attempted to examine non-malignant central nervous system (CNS) neoplasms incidence rates for workers at 8 jet engine manufacturing facilities in Connecticut. The objective of this manuscript is to describe difficulties encountered regarding these analyses to aid future studies. We traced the cohort for incident cases of CNS neoplasms in states where 95% of deaths in the total cohort occurred. We used external and internal analyses in an attempt to obtain the true risk of non-malignant CNS in the cohort. Because these analyses were limited by data constraints, we conducted sensitivity analyses, including using state driver's license data to adjust person-year stop dates to help minimize underascertainment and more accurately determine cohort risk estimates. We identified 3 unanticipated challenges: case identification, determination of population-based cancer incidence rates, and handling of case underascertainment. These factors precluded an accurate assessment of non-malignant CNS neoplasm incidence risks in this occupational epidemiology study. The relatively recent (2004) mandate of capturing non-malignant CNS tumor data at the state level means that, in time, it may be possible to conduct external analyses of these data. Meanwhile, similar occupational epidemiology studies may be limited to descriptive analysis of the non-malignant CNS case characteristics.

Outbreak of sudden cardiac deaths in a tire manufacturing facility: can it be caused by nanoparticles?

PubMed

Kim, Eun-A; Park, Jungsun; Kim, Kun-Hyung; Lee, Naroo; Kim, Dae-Seong; Kang, Seong-Kyu

2012-03-01

The purpose of this study was to review clinical characteristics and working environments of sudden cardiac death (SCD) cases associated with a tire manufacturer in Korea, and review possible occupational risk factors for cardiovascular disease including nanoparticles (ultrafine particles, UFPs). We reviewed (i) the clinical course of SCD cases and (ii) occupational and non-occupational risk factors including chemicals, the physical work environment, and job characteristics. Possible occupational factors were chemicals, UFPs of rubber fume, a hot environment, shift work, overworking, and noise exposure. The mean diameter of rubber fume (63-73 nm) was (larger than diesel exhaust [12 nm] and outdoor dust [50 nm]). The concentration of carbon disulfide, carbon monoxide and styrene were lower than the limit of detection. Five SCD cases were exposed to shift work and overworking. Most of the cases had several non-occupational factors such as hypertension, overweight and smoking. The diameter of rubber fume was larger than outdoor and the diesel exhaust, the most well known particulate having a causal relationship with cardiovascular disease. The possibility of a causal relation between UFPs of rubber fume and SCD was not supported in this study. However, it is necessary to continue studying the relationship between large sized UFPs and SCD.

Outbreak of Sudden Cardiac Deaths in a Tire Manufacturing Facility: Can It Be Caused by Nanoparticles?

PubMed Central

Kim, Eun-A; Kim, Kun-Hyung; Lee, Naroo; Kim, Dae-Seong; Kang, Seong-Kyu

2012-01-01

Objectives The purpose of this study was to review clinical characteristics and working environments of sudden cardiac death (SCD) cases associated with a tire manufacturer in Korea, and review possible occupational risk factors for cardiovascular disease including nanoparticles (ultrafine particles, UFPs). Methods We reviewed (i) the clinical course of SCD cases and (ii) occupational and non-occupational risk factors including chemicals, the physical work environment, and job characteristics. Results Possible occupational factors were chemicals, UFPs of rubber fume, a hot environment, shift work, overworking, and noise exposure. The mean diameter of rubber fume (63-73 nm) was (larger than diesel exhaust [12 nm] and outdoor dust [50 nm]). The concentration of carbon disulfide, carbon monoxide and styrene were lower than the limit of detection. Five SCD cases were exposed to shift work and overworking. Most of the cases had several non-occupational factors such as hypertension, overweight and smoking. Conclusion The diameter of rubber fume was larger than outdoor and the diesel exhaust, the most well known particulate having a causal relationship with cardiovascular disease. The possibility of a causal relation between UFPs of rubber fume and SCD was not supported in this study. However, it is necessary to continue studying the relationship between large sized UFPs and SCD. PMID:22953232

21 CFR 1301.33 - Application for bulk manufacture of Schedule I and II substances.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 9 2013-04-01 2013-04-01 false Application for bulk manufacture of Schedule I and II substances. 1301.33 Section 1301.33 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF... manufacture of Schedule I and II substances. (a) In the case of an application for registration or...

27 CFR 478.92 - How must licensed manufacturers and licensed importers identify firearms, armor piercing...

Code of Federal Regulations, 2010 CFR

2010-04-01

... Conduct of Business § 478.92 How must licensed manufacturers and licensed importers identify firearms... business; and (E) In the case of an imported firearm, the name of the country in which it was manufactured... place of business. For additional requirements relating to imported firearms, see Customs regulations at...

Democratizing science with the aid of parametric design and additive manufacturing: Design and fabrication of a versatile and low-cost optical instrument for scattering measurement.

PubMed

Nadal-Serrano, Jose M; Nadal-Serrano, Adolfo; Lopez-Vallejo, Marisa

2017-01-01

This paper focuses on the application of rapid prototyping techniques using additive manufacturing in combination with parametric design to create low-cost, yet accurate and reliable instruments. The methodology followed makes it possible to make instruments with a degree of customization until now available only to a narrow audience, helping democratize science. The proposal discusses a holistic design-for-manufacturing approach that comprises advanced modeling techniques, open-source design strategies, and an optimization algorithm using free parametric software for both professional and educational purposes. The design and fabrication of an instrument for scattering measurement is used as a case of study to present the previous concepts.

Democratizing science with the aid of parametric design and additive manufacturing: Design and fabrication of a versatile and low-cost optical instrument for scattering measurement

PubMed Central

Lopez-Vallejo, Marisa

2017-01-01

This paper focuses on the application of rapid prototyping techniques using additive manufacturing in combination with parametric design to create low-cost, yet accurate and reliable instruments. The methodology followed makes it possible to make instruments with a degree of customization until now available only to a narrow audience, helping democratize science. The proposal discusses a holistic design-for-manufacturing approach that comprises advanced modeling techniques, open-source design strategies, and an optimization algorithm using free parametric software for both professional and educational purposes. The design and fabrication of an instrument for scattering measurement is used as a case of study to present the previous concepts. PMID:29112987

Challenges with the introduction of radio-frequency identification systems into a manufacturer's supply chain - a pilot study

NASA Astrophysics Data System (ADS)

Kumar, Sameer; Kadow, Brooke B.; Lamkin, Melissa K.

2011-05-01

As radio-frequency identification (RFID) implementation becomes more widespread it is important for managers to consider if this technology is right for their businesses. This study examines challenges of RFID implementation along with a cost-benefit analysis of a pharmaceuticals manufacturer's supply chain. Research was gathered from a variety of sources on the topic of RFID to provide an in-depth analysis of challenges and benefits found with RFID systems. Furthermore, the study reviews the real case applications of the RFID technology in healthcare and customer services. Many of the challenges with RFID stem from improper planning of the synchronisation of the supply chain and the integration of RFID technology into facilities and software systems. Customer privacy, excess information and obsolete technology are also of concern to companies considering RFID. Benefits such as increased information sharing, product visibility and real-time information help to offset these challenges. In addition, pharmaceuticals manufacturer real case application showed cost savings from reducing labour and decreased opportunities for lost product counteract the expense to implement an RFID system. This study will be of value to managers who are attempting to implement RFID technology in their companies. It is intended that readers, both academics and practitioners, will be able to identify possible challenges and mitigate them as the RFID technology is put into practice.

CASE STUDIES: LOW-VOC/HAP WOOD FURNITURE COATINGS (PROJECT SUMMARY)

EPA Science Inventory

The report gives results of a study in which wood furniture manufacturing fa-cilities were identified that had converted at least one of their primary coating steps to low-volatile organic compound (VOC)/hazardous air pollut-ant (HAP) wood furniture coatings [high-solids, waterbo...

Contamination during production of heater-cooler units by Mycobacterium chimaera potential cause for invasive cardiovascular infections: results of an outbreak investigation in Germany, April 2015 to February 2016.

PubMed

Haller, Sebastian; Höller, Christiane; Jacobshagen, Anja; Hamouda, Osamah; Abu Sin, Muna; Monnet, Dominique L; Plachouras, Diamantis; Eckmanns, Tim

2016-04-28

Invasive infections with Mycobacterium chimaera were reported in patients with previous open chest surgery and exposure to contaminated heater-cooler units (HCUs). We present results of the surveillance of clinical cases and of contaminated HCUs as well as environmental investigations in Germany up until February 2016. Clinical infections occurred in five male German cases over 50 years of age (range 53-80). Cases had been exposed to HCUs from one single manufacturer during open chest surgery up to five years prior to onset of symptoms. During environmental investigations, M. chimaera was detected in samples from used HCUs from three different countries and samples from new HCUs as well as in the environment at the manufacturing site of one manufacturer in Germany. Our investigation suggests that at least some of the M. chimaera infections may have been caused by contamination of HCUs at manufacturing site. We recommend that until sustainable measures for safe use of HCUs in operation theatres are implemented, users continue to adhere to instructions for use of HCUs and Field Safety Notices issued by the manufacturer, implement local monitoring for bacterial contamination and continuously check the websites of national and European authorities for current recommendations for the safe operation of HCUs.

Perceptions of water scarcity: The case of Genadendal and outstations

NASA Astrophysics Data System (ADS)

Noemdoe, S.; Jonker, L.; Swatuk, L. A.

The water resources management regime has shifted from one focusing almost exclusively on augmenting supply to one where ensuring access, equity and sustainability are an integral part of process. It is widely recognized that South Africa will face water scarcity in the near future. But ‘scarcity’, as we show in our case study, is a relative concept. This paper interrogates perceptions of scarcity in the small South African rural community of Greater Genadendal. Using a wide variety of data, we explore the intersection between poverty alleviation and adequate water supply. The results show that notwithstanding sufficient water being available, the community experiences what Mehta [Mehta, L., 2001. The manufacture of popular perceptions of scarcity: dams and water-related narratives in Gujarat, India. World Development 29 (12), 2025-2041] calls ‘manufactured scarcity’. This is due to inadequate infrastructure, institutional incapacity and a history of political inequality. In the case of Greater Genadendal, these forms of scarcity are present simultaneously leading to a very complex situation. Overcoming these types of scarcity, however, require more than just new infrastructure. They require socio-economic and socio-political types of intervention that target the bases for manufactured scarcity: abiding poverty and socio-inequality. However, there appears to be a lack of social capital, in particular the trust that would enable government and local people to work together for improved livelihoods and sustainable water supplies. Joint resource rehabilitation activities may be one way of building social capital and moving toward IWRM in the study area.

Occupational risk factors for brain cancer: a population-based case-control study in Iowa.

PubMed

Zheng, T; Cantor, K P; Zhang, Y; Keim, S; Lynch, C F

2001-04-01

A number of occupations and industries have been inconsistently associated with the risk of brain cancer. To further explore possible relationships, we conducted a population-based case-control study of brain glioma in the state of Iowa, involving 375 histologically confirmed incident cases and 2434 population-based controls. Among men, the industries and/or occupations that had a significantly increased risk for employment of more than 10 years included roofing, siding, and sheet metalworking; newspaper work; rubber and plastics products, particularly tires and inner tubes; miscellaneous manufacturing industries; wholesale trade of durable goods, grain, and field beans; cleaning and building service occupations; miscellaneous mechanics and repairers; and janitors and cleaners. Subjects who worked in plumbing, heating, and air conditioning; electrical services; gasoline service stations; and military occupations also experienced a significantly increased risk. Among women, significant excess risk was observed for occupations in agricultural services and farming, apparel and textile products, electrical and electronic equipment manufacturing, various retail sales, record-keeping, and restaurant service. Workers in industries with a potential for gasoline or motor exhaust exposures experienced a non-significant excess risk of brain glioma.

Vision-related problems among the workers engaged in jewellery manufacturing.

PubMed

Salve, Urmi Ravindra

2015-01-01

American Optometric Association defines Computer Vision Syndrome (CVS) as "complex of eye and vision problems related to near work which are experienced during or related to computer use." This happens when visual demand of the tasks exceeds the visual ability of the users. Even though problems were initially attributed to computer-related activities subsequently similar problems are also reported while carrying any near point task. Jewellery manufacturing activities involves precision designs, setting the tiny metals and stones which requires high visual attention and mental concentration and are often near point task. It is therefore expected that the workers engaged in jewellery manufacturing may also experience symptoms like CVS. Keeping the above in mind, this study was taken up (1) To identify the prevalence of symptoms like CVS among the workers of the jewellery manufacturing and compare the same with the workers working at computer workstation and (2) To ascertain whether such symptoms have any permanent vision-related problems. Case control study. The study was carried out in Zaveri Bazaar region and at an IT-enabled organization in Mumbai. The study involved the identification of symptoms of CVS using a questionnaire of Eye Strain Journal, opthalmological check-ups and measurement of Spontaneous Eye Blink rate. The data obtained from the jewellery manufacturing was compared with the data of the subjects engaged in computer work and with the data available in the literature. A comparative inferential statistics was used. Results showed that visual demands of the task carried out in jewellery manufacturing were much higher than that of carried out in computer-related work.

Mortality from nephritis and nephrosis in the fibreglass manufacturing industry

PubMed Central

Chiazze, L.; Watkins, D. K.; Fryar, C.; Fayerweather, W.; Bender, J. R.; Chiazze, M.

1999-01-01

OBJECTIVES: To investigate the question of whether there is an association between exposure to silica or respirable glass fibre and mortality from nephritis or nephrosis among workers in fibrous glass wool manufacturing facilities. METHODS: A case-control study with cases and controls derived from the Owens Corning mortality surveillance system. Two case-control analyses were carried out, one where the cases are defined with nephritis or nephrosis as the underlying cause of death and one where cases are defined as those where nephritis or nephrosis is either the underlying or a contributing cause of death. RESULTS: There is no consistent relation between respirable fibres or respirable silica and nephritis or nephrosis when the analysis is based either on underlying cause only or on underlying plus contributing cause of death. None of the sociodemographic variables considered suggests an increased risk when considering both underlying and contributing cause of death. CONCLUSIONS: These data would seem to support the contention that the most accurate picture of renal disease will be gained from the use of all information on the death certificate and not only the underlying cause. For these data, all odds ratios (ORs) for respirable fibres and silica based on both underlying and contributing cause of death are < 1 with the exception of the highest exposure to silica which is slightly > 1 (OR = 1.04). Although these results do not prove that there is no association between nephritis and nephrosis and exposure to fibreglass or silica in the fibreglass manufacturing environment, they do not support the assertion that such an association exists.   PMID:10448324

Collaboration management framework for OEM - suppliers relationships: a trust-based conceptual approach

NASA Astrophysics Data System (ADS)

Belkadi, Farouk; Messaadia, Mourad; Bernard, Alain; Baudry, David

2017-08-01

Due to the increased competitiveness and the diversity of requirements in today's markets, manufacturing companies need to join their competencies and resources to propose innovative solutions for each specific market, with the possibility to transpose these solutions to another market, by means of slight adaptations. Thus, manufacturing firms must constantly conduct new collaborations with known partners in most cases, but also with new partners. The critical question for managers in this latter case is how to define the best collaborative strategy according to the goals of the project and the specificity of the target market. This paper tackles the problem by proposing a conceptual framework for supporting the management of collaborative situations in the case of Original equipment manufacturers (OEMs). Based on the concept of trust level, the framework proposes a classification of different collaboration modes to be adopted in various contexts of inter-enterprise relationships, in manufacturing sector. The aim is to support the flexible navigation between different collaborative situations by taking into account all decision-making levels from the strategy to the implementation of the information technologies (IT) systems at the operational level.

Using the Fuzzy DEMATEL to Determine Environmental Performance: A Case of Printed Circuit Board Industry in Taiwan

PubMed Central

Tsai, Sang-Bing; Chien, Min-Fang; Xue, Youzhi; Li, Lei; Jiang, Xiaodong; Chen, Quan; Zhou, Jie; Wang, Lei

2015-01-01

The method by which high-technology product manufacturers balance profits and environmental performance is of crucial concern for governments and enterprises. To examine the environmental performance of manufacturers, the present study applied Fuzzy-DEMATEL model to examine environmental performance of the PCB industry in Taiwan. Fuzzy theory was employed to examine the environmental performance criteria of manufacturers and analyse fuzzy linguistics. The fuzzy-DEMATEL model was then employed to assess the direction and level of interaction between environmental performance criteria. The core environmental performance criteria which were critical for enhancing environmental performance of the PCB industry in Taiwan were identified and presented. The present study revealed that green design (a1), green material procurement (a2), and energy consumption (b3) constitute crucial reason criteria, the core criteria influencing other criteria, and the driving factors for resolving problems. PMID:26052710

Using the Fuzzy DEMATEL to Determine Environmental Performance: A Case of Printed Circuit Board Industry in Taiwan.

PubMed

Tsai, Sang-Bing; Chien, Min-Fang; Xue, Youzhi; Li, Lei; Jiang, Xiaodong; Chen, Quan; Zhou, Jie; Wang, Lei

2015-01-01

The method by which high-technology product manufacturers balance profits and environmental performance is of crucial concern for governments and enterprises. To examine the environmental performance of manufacturers, the present study applied Fuzzy-DEMATEL model to examine environmental performance of the PCB industry in Taiwan. Fuzzy theory was employed to examine the environmental performance criteria of manufacturers and analyse fuzzy linguistics. The fuzzy-DEMATEL model was then employed to assess the direction and level of interaction between environmental performance criteria. The core environmental performance criteria which were critical for enhancing environmental performance of the PCB industry in Taiwan were identified and presented. The present study revealed that green design (a1), green material procurement (a2), and energy consumption (b3) constitute crucial reason criteria, the core criteria influencing other criteria, and the driving factors for resolving problems.

Micro-dynamics of business location and growth and its effects on the transportation network and congestion in Georgia and the southeast region.

DOT National Transportation Integrated Search

2014-08-01

The project explored the linkages between industry dynamics and economic activity, and the : macro-congestion aspects of freight transport. The Kia Motors manufacturing plant near West Point, : Georgia was selected for case study. The principal study...

Workplace Skills in Practice. Case Studies of Technical Work.

ERIC Educational Resources Information Center

Stasz, Cathleen; And Others

A study was conducted to explore skills and work-related dispositions in technical work. It used a sociocultural approach to examine skills in seven target jobs in worksites representing diverse industries--health care, traffic management, transportation, and semiconductor manufacturing. It explored employers' strategies for obtaining the skills…

A Multimedia Database Management System Supporting Contents Search in Media Data

DTIC Science & Technology

1989-03-01

predicates: car (x), manufacturer (x, Horch ), year-built (x, 1922) to designate that the car was manufactured by Horch in the year 1922. The use of the name...manufacturer (imagel, x, " Horch "). year-built (imagel, x, 1922). query(I) :- car (I, Z), manufacturer (I, Z, " Horch "). ?- query(Image). yes. Image = image... Horch ) : imageJ 1, imageJ2, etc. In certain cases a predicate may generate entries in more than one list. For example, if the predicate of action

1400314

NASA Image and Video Library

2014-04-21

2. ENGINEERS AND TECHNICIANS PREPARE FOR AN UPCOMING HOT-FIRE TEST OF A ROCKET INJECTOR MANUFACTURED USING ADDITIVE MANUFACTURING, OR 3-D PRINTING…(L TO R) WILLIE PARKER, INFOPRO TECHNICIAN, BRAD BULLARD, NASA, NICK CASE, NASA, AND RANDALL MCALLISTER, INFOPRO TECHNICIAN

Integration of Optimal Scheduling with Case-Based Planning.

DTIC Science & Technology

1995-08-01

integrates Case-Based Reasoning (CBR) and Rule-Based Reasoning (RBR) systems. ’ Tachyon : A Constraint-Based Temporal Reasoning Model and Its...Implementation’ provides an overview of the Tachyon temporal’s reasoning system and discusses its possible applications. ’Dual-Use Applications of Tachyon : From...Force Structure Modeling to Manufacturing Scheduling’ discusses the application of Tachyon to real world problems, specifically military force deployment and manufacturing scheduling.

Toward Eco Product Development with Qualitative and CAE Design Process - Case Study of Flame Guiding Module

NASA Astrophysics Data System (ADS)

Chen, W. L.; Chao, F. L.

2018-04-01

Sustainable products become increasingly important for company in addressing eco-performance to satisfy global environmental regulations. Case study of flame guiding module reviewed design process and concerns related to the torch design. For enhancing flame height, the torch was embedded with an airflow guidance structure. The design process and design methodologies were investigated as an eco-design case study. Combine qualitative and CAE simulation were proposed to fulfil its main and auxiliary functions including reduction of impact during use. The design guidelines help prevent mistake arrangements, CAE helps understand combustion phenomenon. The flow field simulation enables fine tune of geometric design. Functional test and measurement are carried out to confirm the product features. On Eco-performance, we choose 5 items for evaluation the status of previous and redesign module, namely function need, low impact material, few manufacturing steps, low energy consumption, and safety. The radar diagram indicates that eco-performance of redesign module is better. Life cycle assessment calculated the carbon footprint of the manufacturing and processing stage with Eco-it. By using recycled steel in the flame module, it reduces raw material stage carbon footprint significantly.

Laser Additive Manufacturing of Magnetic Materials

NASA Astrophysics Data System (ADS)

Mikler, C. V.; Chaudhary, V.; Borkar, T.; Soni, V.; Jaeger, D.; Chen, X.; Contieri, R.; Ramanujan, R. V.; Banerjee, R.

2017-03-01

While laser additive manufacturing is becoming increasingly important in the context of next-generation manufacturing technologies, most current research efforts focus on optimizing process parameters for the processing of mature alloys for structural applications (primarily stainless steels, titanium base, and nickel base alloys) from pre-alloyed powder feedstocks to achieve properties superior to conventionally processed counterparts. However, laser additive manufacturing or processing can also be applied to functional materials. This article focuses on the use of directed energy deposition-based additive manufacturing technologies, such as the laser engineered net shaping (LENS™) process, to deposit magnetic alloys. Three case studies are presented: Fe-30 at.%Ni, permalloys of the type Ni-Fe-V and Ni-Fe-Mo, and Fe-Si-B-Cu-Nb (derived from Finemet) alloys. All these alloys have been processed from a blend of elemental powders used as the feedstock, and their resultant microstructures, phase formation, and magnetic properties are discussed in this paper. Although these alloys were produced from a blend of elemental powders, they exhibited relatively uniform microstructures and comparable magnetic properties to those of their conventionally processed counterparts.

3D planning in orthognathic surgery: CAD/CAM surgical splints and prediction of the soft and hard tissues results - our experience in 16 cases.

PubMed

Aboul-Hosn Centenero, Samir; Hernández-Alfaro, Federico

2012-02-01

The aim of this article is to determine the advantages of 3D planning in predicting postoperative results and manufacturing surgical splints using CAD/CAM (Computer Aided Design/Computer Aided Manufacturing) technology in orthognathic surgery when the software program Simplant OMS 10.1 (Materialise(®), Leuven, Belgium) was used for the purpose of this study which was carried out on 16 patients. A conventional preoperative treatment plan was devised for each patient following our Centre's standard protocol, and surgical splints were manufactured. These splints were used as study controls. The preoperative treatment plans devised were then transferred to a 3D-virtual environment on a personal computer (PC). Surgery was simulated, the prediction of results on soft and hard tissue produced, and surgical splints manufactured using CAD/CAM technology. In the operating room, both types of surgical splints were compared and the degree of similitude in results obtained in three planes was calculated. The maxillary osteotomy line was taken as the point of reference. The level of concordance was used to compare the surgical splints. Three months after surgery a second set of 3D images were obtained and used to obtain linear and angular measurements on screen. Using the Intraclass Correlation Coefficient these postoperative measurements were compared with the measurements obtained when predicting postoperative results. Results showed that a high degree of correlation in 15 of the 16 cases. A high coefficient of correlation was obtained in the majority of predictions of results in hard tissue, although less precise results were obtained in measurements in soft tissue in the labial area. The study shows that the software program used in the study is reliable for 3D planning and for the manufacture of surgical splints using CAD/CAM technology. Nevertheless, further progress in the development of technologies for the acquisition of 3D images, new versions of software programs, and further studies of objective data are necessary to increase precision in computerised 3D planning. Copyright © 2011 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Strategic Downsizing and Learning Organisations.

ERIC Educational Resources Information Center

Griggs, Harvey E.; Hyland, Paul

2003-01-01

Downsizing or brain drain may damage the learning capacity of organizations. A case study of an aerospace manufacturing firm shows that appropriate strategies to analyze the impact on formal and informal learning networks may help manage or minimize the damage. (Contains 55 references.) (SK)

A CASE STUDY OF CANCER DATA SET COMBINATIONS FOR PCBs

EPA Science Inventory

Results of several animal bioassays have demonstrated the carcinogenic potential of polychlorinated biphenyl (PCB) mixtures. Although PCBs are no longer manufactured, cancer risk assessment for PCBs remains an important issue because of continued potential human exposure from man...

Upgrade of Compressed Air Control System Reduces Energy Costs at Michelin Tire Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2002-01-01

This case study highlights the upgraded compressed air system at a Michelin tire manufacturing plant in Spartanburg, South Carolina. The controls upgrade project enabled multiple compressor operation without blow-off, and significantly reduced energy costs.

Information Systems and Management Training.

ERIC Educational Resources Information Center

Curry, B.; Smith, D. G.

1991-01-01

A case study of a South Wales manufacturer illustrates the need for companies to adopt an integrated strategy for computerization and information systems. Lack of management training blending computing and business skills can have a crippling effect on system development and organizational health. (SK)

A grey DEMATEL-based approach for modeling enablers of green innovation in manufacturing organizations.

PubMed

Gupta, Himanshu; Barua, Mukesh Kumar

2018-04-01

Incorporating green practices into the manufacturing process has gained momentum over the past few years and is a matter of great concern for both manufacturers as well as researchers. Regulatory pressures in developed countries have forced the organizations to adopt green practices; however, this issue still lacks attention in developing economies like India. There is an urgent need to identify enablers of green innovation for manufacturing organizations and also to identify prominent enablers among those. This study is an attempt to first identify enablers of green innovation and then establish a causal relationship among them to identify the enablers that can drive others. Grey DEMATEL (Decision Making Trial and Evaluation Laboratory) methodology is used for establishing the causal relationship among enablers. The novelty of this study lies in the fact that no study has been done in the past to identify the enablers of green innovation and then establishing the causal relationship among them. A total of 21 enablers of green innovation have been identified; research indicates developing green manufacturing capabilities, resources for green innovation, ease of getting loans from financial institutions, and environmental regulations as the most influential enablers of green innovation. Managerial and practical implications of the research are also presented to assist managers of the case company in adopting green innovation practices at their end.

The role of private industry in pragmatic comparative effectiveness trials.

PubMed

Buesching, Don P; Luce, Bryan R; Berger, Marc L

2012-03-01

Comparative effectiveness research (CER) includes pragmatic clinical trials (PCTs) to address 'real-world' effectiveness. CER interest would be expected to stimulate biopharmaceutical manufacturer PCT investment; however, this does not seem to be the case. In this article we identify all industry-sponsored PCT studies from 1996 to 2010; analyze them across a variety of characteristics, including sponsor, research question, design, comparators and results; and suggest methodological and policy changes to spur future manufacturer PCT investment. Nine 'naturalistic', head-to-head versus standard of care or similar agent PCTs were identified. Two included a 'usual care' arm. Chronic care trials' length averaged 12 months (range: 6-24 months), six of which reported equivocal or no difference in effectiveness; results of two chronic and the single acute care PCTs favored the sponsor drug. None reported the sponsor drug inferior. Of seven that evaluated utilization or costs, six reported no differences and four of five studies comparing brand-generic drugs reported no difference. Whereas private investment in PCTs is in the public interest, manufacturers apparently have not yet seen the business case. To induce investment, we propose several methodological and regulatory policy innovations designed to reduce business risk by decreasing outcome variability and increasing trial efficiency, flexibility and market applicability.

Are computer numerical control (CNC)-manufactured patient-specific metal templates available for posterior thoracic pedicle screw insertion? Feasibility and accuracy evaluation.

PubMed

Kong, Xiangxue; Tang, Lei; Ye, Qiang; Huang, Wenhua; Li, Jianyi

2017-11-01

Accurate and safe posterior thoracic pedicle insertion (PTPI) remains a challenge. Patient-specific drill templates (PDTs) created by rapid prototyping (RP) can assist in posterior thoracic pedicle insertion, but pose biocompatibility risks. The aims of this study were to develop alternative PDTs with computer numerical control (CNC) and assess their feasibility and accuracy in assisting PTPI. Preoperative CT images of 31 cadaveric thoracic vertebras were obtained and then the optimal pedicle screw trajectories were planned. The PDTs with optimal screw trajectories were randomly assigned to be designed and manufactured by CNC or RP in each vertebra. With the guide of the CNC- or RP-manufactured PDTs, the appropriate screws were inserted into the pedicles. Postoperative CT scans were performed to analyze any deviations at entry point and midpoint of the pedicles. The CNC group was found to be significant manufacture-time-shortening, and cost-decreasing, when compared with the RP group (P < 0.01). The PDTs fitted the vertebral laminates well while all screws were being inserted into the pedicles. There were no significant differences in absolute deviations at entry point and midpoint of the pedicle on either axial or sagittal planes (P > 0.05). The screw positions were grade 0 in 90.3% and grade 1 in 9.7% of the cases in the CNC group and grade 0 in 93.5% and grade 1 in 6.5% of the cases in the RP group (P = 0.641). CNC-manufactured PDTs are viable for assisting in PTPI with good feasibility and accuracy.

Failure to Treat Life-Threatening Ventricular Tachyarrhythmias in Contemporary Implantable Cardioverter–Defibrillators

PubMed Central

Thøgersen, Anna Margrethe; Larsen, Jacob Moesgaard; Johansen, Jens Brock; Abedin, Moeen

2017-01-01

Background: In clinical trials, manufacturer-specific, strategic programming of implantable cardioverter–defibrillators (ICDs), including faster detection rates, reduces unnecessary therapy but permits therapy for ventricular tachycardia/ventricular fibrillation (VF). Present consensus recommends a generic rate threshold between 185 and 200 beats per minute, which exceeds the rate tested in clinical trials for some manufacturers. In a case series, we sought to determine the relationship between programmed parameters and failure of modern ICDs to treat VF. Methods and Results: We reviewed cases in which normally functioning ICDs failed to deliver timely therapy for VF from April 2015 to January 2017 at 4 institutions. Of 10 ambulatory patients, 5 died from untreated VF, 4 had cardiac arrests requiring external shocks, and 1 was rescued by a delayed ICD shock. VF did not satisfy programmed detection criteria in 9 patients (90%). Seven of these patients had slowest detection rates that were consistent with generic recommendations but not tested in a peer-reviewed trial for their manufacturer’s ICDs. Manufacturer-specific factors interacted with fast detection rates to withhold therapy, including strict VF episode termination rules, enhancements to minimize T-wave oversensing, and features that restrict therapy to regular rhythms in ventricular tachycardia zones. Untreated VF despite recommended programming accounted for 56% of sudden deaths and 11% of all deaths during the study period. Conclusions: Complex and unanticipated interactions between manufacturer-specific features and generic programming can prevent therapy for VF. More data are needed to assess the risks and benefits of translating evidence-based detection parameters from one manufacturer to another. PMID:28916511

Occupational injury and illness in the semiconductor manufacturing industry.

PubMed

McCurdy, S A; Schenker, M B; Lassiter, D V

1989-01-01

Two thousand nine hundred and ninety-four reports of OSHA-reportable occupational injury or illness cases in 1984 from member companies of a national trade association of semiconductor manufacturing firms were analyzed. The 37 participating manufacturing facilities represented 16 companies employing over 95,000 persons, or approximately one-third of the U.S. work force for this industry in 1984. The annual incidence rate for all reportable injuries and illnesses was 2.7 per 100 full-time employees (FTE) for men and 3.7 per 100 FTE for women. Strains, sprains, or dislocations were the most frequently reported incidents (N = 956 [31.9%]), followed by cuts, lacerations, punctures, scratches, and abrasions (N = 445 [14.9%]), and chemical burns (N = 401 [13.4%]). Increased work-loss days per case were associated with manufacturing sites that did not have an employee health clinic on the premises, with custodial occupations, and with female gender.

Study of a dry room in a battery manufacturing plant using a process model

NASA Astrophysics Data System (ADS)

Ahmed, Shabbir; Nelson, Paul A.; Dees, Dennis W.

2016-09-01

The manufacture of lithium ion batteries requires some processing steps to be carried out in a dry room, where the moisture content should remain below 100 parts per million. The design and operation of such a dry room adds to the cost of the battery. This paper studied the humidity management of the air to and from the dry room to understand the impact of design and operating parameters on the energy demand and the cost contribution towards the battery manufacturing cost. The study was conducted with the help of a process model for a dry room with a volume of 16,000 cubic meters. For a defined base case scenario it was found that the dry room operation has an energy demand of approximately 400 kW. The paper explores some tradeoffs in design and operating parameters by looking at the humidity reduction by quenching the make-up air vs. at the desiccant wheel, and the impact of the heat recovery from the desiccant regeneration cycle.

Outbreak of Salmonella Goldcoast infections linked to consumption of fermented sausage, Germany 2001.

PubMed Central

Bremer, V.; Leitmeyer, K.; Jensen, E.; Metzel, U.; Meczulat, H.; Weise, E.; Werber, D.; Tschaepe, H.; Kreienbrock, L.; Glaser, S.; Ammon, A.

2004-01-01

Salmonella Goldcoast (SGC), an uncommon serotype in Germany, was identified in 25 isolates between 1 April and 7 May 2001. To determine the cause of the outbreak, we conducted a matched case-control study including 24 cases and 51 controls. In a multivariable regression model, only consumption of a raw fermented sausage manufactured by a local company remained significant (adjusted odds ratio 20.0, 95 % confidence interval 2.7-302.5). SGC isolated from case-patients shared an indistinguishable pulsed-field gel electrophoresis pattern. A part of the produced raw fermented sausage was sold after only 4 days of fermentation. Samples from the premises and products of the company were negative for SGC. However, short-time raw fermented sausage is more likely to contain pathogens. Irradiation of raw ingredients is not accepted by German consumers, thus strict adherence to good manufacturing practices, the use of HACCP programmes as well as on-farm programmes remain crucial to reduce Salmonella. PMID:15473151

Outbreak of Salmonella Goldcoast infections linked to consumption of fermented sausage, Germany 2001.

PubMed

Bremer, V; Leitmeyer, K; Jensen, E; Metzel, U; Meczulat, H; Weise, E; Werber, D; Tschaepe, H; Kreienbrock, L; Glaser, S; Ammon, A

2004-10-01

Salmonella Goldcoast (SGC), an uncommon serotype in Germany, was identified in 25 isolates between 1 April and 7 May 2001. To determine the cause of the outbreak, we conducted a matched case-control study including 24 cases and 51 controls. In a multivariable regression model, only consumption of a raw fermented sausage manufactured by a local company remained significant (adjusted odds ratio 20.0, 95 % confidence interval 2.7-302.5). SGC isolated from case-patients shared an indistinguishable pulsed-field gel electrophoresis pattern. A part of the produced raw fermented sausage was sold after only 4 days of fermentation. Samples from the premises and products of the company were negative for SGC. However, short-time raw fermented sausage is more likely to contain pathogens. Irradiation of raw ingredients is not accepted by German consumers, thus strict adherence to good manufacturing practices, the use of HACCP programmes as well as on-farm programmes remain crucial to reduce Salmonella.

Using genetic algorithm to determine the optimal order quantities for multi-item multi-period under warehouse capacity constraints in kitchenware manufacturing

NASA Astrophysics Data System (ADS)

Saraswati, D.; Sari, D. K.; Johan, V.

2017-11-01

The study was conducted on a manufacturer that produced various kinds of kitchenware with kitchen sink as the main product. There were four types of steel sheets selected as the raw materials of the kitchen sink. The problem was the manufacturer wanted to determine how much steel sheets to order from a single supplier to meet the production requirements in a way to minimize the total inventory cost. In this case, the economic order quantity (EOQ) model was developed using all-unit discount as the price of steel sheets and the warehouse capacity was limited. Genetic algorithm (GA) was used to find the minimum of the total inventory cost as a sum of purchasing cost, ordering cost, holding cost and penalty cost.

10 CFR 2.501 - Notice of hearing on application under subpart F of 10 CFR part 52 for a license to manufacture...

Code of Federal Regulations, 2011 CFR

2011-01-01

... part 52 for a license to manufacture nuclear power reactors. 2.501 Section 2.501 Energy NUCLEAR... Procedures Applicable to Proceedings for the Issuance of Licenses To Manufacture Nuclear Power Reactors To Be... power reactors. (a) In the case of an application under subpart F of part 52 of this chapter for a...

10 CFR 2.501 - Notice of hearing on application under subpart F of 10 CFR part 52 for a license to manufacture...

Code of Federal Regulations, 2010 CFR

2010-01-01

... part 52 for a license to manufacture nuclear power reactors. 2.501 Section 2.501 Energy NUCLEAR... Procedures Applicable to Proceedings for the Issuance of Licenses To Manufacture Nuclear Power Reactors To Be... power reactors. (a) In the case of an application under subpart F of part 52 of this chapter for a...

Reconstruction of an Extensive Midfacial Defect Using Additive Manufacturing Techniques.

PubMed

Fernandes, Nelson; van den Heever, Jacobus; Hoogendijk, Christiaan; Botha, Sarel; Booysen, Gerrie; Els, Johan

2016-10-01

Malignant peripheral nerve sheath tumors are extremely rare tumors arising in peripheral nerves. Only 17 cases involving the trigeminal nerve have ever been reported. These tumors have a very poor prognosis and very high rates of recurrence and metastases. Their recommended treatment involves complete tumor resection followed by radiation. This can be problematic in the head and neck region. We present a clinical case involving a 33-year-old female patient presenting with a slow-growing, exophytic mass of the anterior maxilla. Incisional biopsy and subsequent histological examination revealed a diagnosis of a malignant peripheral nerve sheath tumor. Surgical resection involved a complete maxillectomy, rhinectomy, and resection of the upper lip and aspects of the left and right cheeks. Reconstruction of the subsequent defect incorporated the placement of four zygomatic oncology implants to aid in retention of a facial prosthesis. These implants, however, were subsequently lost; and an anatomical model of the hard tissues was manufactured via 3D printing. This model was used to design and manufacture a titanium frame (customized implant) for the patient. The frame was then fixated and secured intraoperatively with 21 cortical screws. A maxillary denture and silicone facial prosthesis were also made to fit onto this frame. This is the first known case where additive manufacturing, via the use of rapid prototyping and 3D printing, was employed to manufacture a facial prosthesis. © 2016 by the American College of Prosthodontists.

Passenger car crippling end-load test and analyses

DOT National Transportation Integrated Search

2017-09-01

The Transportation Technology Center, Inc. (TTCI) performed a series of full-scale tests and a finite element analysis (FEA) in a case study that may become a model for manufacturers seeking to use the waiver process of Tier I crashworthiness and occ...

Atha Road Elementary School, Monroe, Georgia.

ERIC Educational Resources Information Center

Design Cost Data, 2002

2002-01-01

Describes the building design of the library and technology center named in the title, including the educational context and design goals. Includes a general description; information on the architect, construction team, and manufacturers and suppliers; and a case study of costs and specifications. (EV)

40 CFR 79.11 - Information and assurances to be provided by the fuel manufacturer.

Code of Federal Regulations, 2010 CFR

2010-07-01

... description (or identification, in the case of a generally accepted method) of a suitable analytical technique... sold, offered for sale, or introduced into commerce for use in motor vehicles manufactured after model...

Hybrid Electric Transit Bus Testing | Transportation Research | NREL

Science.gov Websites

this study are featured in the Long Beach Transit: Two-Year Evaluation of Gasoline-Electric Hybrid manufactured by Orion Industries with BAE propulsion systems. The results of this study are featured in the In power units. The results of this study are featured in the Ebus Hybrid Electric Buses and Trolleys case

GPS Receivers Use-Case Information : GPS Adjacent Band Compatibility Assessment Workshop

DOT National Transportation Integrated Search

2014-09-18

Topics 1. Background. 2. Use Case Template. 3. Description of Submitted UseCases from DOT Extended Pos/Nav Working Group. 4. Utilization of UseCase Information. 5. Request of Information for Additional UseCases from GPS Receiver Manufacturer...

National supply-chain survey of drug manufacturer back orders.

PubMed

Wellman, G S

2001-07-01

The impact of manufacturer back orders on the supply chain for pharmaceuticals in the institutional setting was studied. A questionnaire was distributed during May and June 2000 to 600 institutional pharmacies affiliated with a major national drug and supply group purchasing organization. The instrument included questions on basic institutional demographics, perceptions about the frequency of manufacturer back orders for pharmaceuticals, the quality of communication with manufacturers and wholesalers about back orders, the two most significant back orders that had occurred in the 12 months preceding the survey, and the reasons for and impact of back orders. A total of 170 usable surveys were returned (net response rate, 28.3%). Reported manufacturer back orders included an array of drug classes, including blood products, antimicrobials, antiarrhythmics, benzodiazepine antagonists, thrombolytics, corticosteroids, and antihypertensives. Respondents perceived significant back orders as increasing in frequency. Communication by manufacturers and wholesalers about back orders was reported to be relatively poor. A raw-material shortage was the most common reason given by manufacturers for back orders (36.5%), followed by a regulatory issue (23.2%). In most cases (92%), medical staff members had to be contacted, indicating an interruption in the normal drug distribution process. In over a third of instances, respondents stated that the back order resulted in less optimal therapy. A survey found that manufacturer back orders for pharmaceuticals were increasing in frequency and that information flow within the supply chain was insufficient to meet the needs of end users.

Repairing a Facial Cleft by Polyether-Ether-Ketone Implant Combined With Titanium Mesh.

PubMed

Deng, Yuan; Tang, Weiwei; Li, Zhengkang

2018-05-15

The Tessier Number 4 cleft is one of the rarest, most complex craniofacial anomalies that presents difficulties in surgical treatment. In this article, we report a case of simultaneous facial depression, eye displacement, and medial canthus deformity. In this case, the maxillary bony defect was reconstructed using computer-assisted design computer-assisted manufacturing (CAD-CAM) polyether-ether-ketone (PEEK) material, and the orbital floor defect was repaired with AO prefabricated titanium mesh. Additionally, the medial canthus was modified with canthopexy and a single Z-plasty flap. Owing to its relative rarity and varied clinical presentations, no definitive operative methods have been accepted for Tessier No. 4 facial cleft. This study presents the combination of CAD-CAM manufactured PEEK material and titanium mesh as an alternative approach for reconstructing the bony defect of Tessier No. 4 facial clefts.

Work environment investments: outcomes from three cases.

PubMed

Rydell, Alexis; Andersson, Ing-Marie

2017-09-27

Work environment investments are important in order to create a healthy and safe workplace. This article presents findings from a seven-step interventions process aimed at examining and following-up work environment investments in small and medium-sized enterprises (SMEs), with a particular focus on air contaminants. Three different cases were analyzed and included in the study: (a) an educational center for welding; (b) a paint station in furniture manufacturing; (c) a joinery in furniture manufacturing. The results show that the work environment investments were highly appreciated by the employees and managers, but at the same time the investment could be optimized through markedly decreased exposure levels for the worker. Factors such as follow-ups of the investment, education and training in how to use the equipment, worker involvement in the process and leadership engagement are important in order to optimize work environment investments.

A follow-up study of cancer incidence among workers in manufacture of phenoxy herbicides in Denmark.

PubMed Central

Lynge, E.

1985-01-01

The purpose of this cohort study is to shed further light on the potential carcinogenic effect indicated by a Swedish case control study of the 2,4-dichlorophenol and 4-chloro-ortho-cresol based phenoxy herbicides, unlikely to be contaminated with 2,3,7,8-tetrachlorodibenzo-p-dioxin (2,3,7,8-TCDD). In the present study it was the intention to include all persons employed in manufacture of phenoxy herbicides in Denmark before 1982. The predominant product was MCPA and only a very limited amount of 2,4,5-T was processed in one of the two factories included in the study. Registration of the cohort was based on company records, supplemented with data from a public pension scheme from 1964 onwards. Ninety-nine percent of registered employees could be followed up. Cancer cases were identified by linkage with the National Cancer Register. Totals of 3,390 males and 1,069 females were included in the study. In the analysis special attention was given to soft tissue sarcomas (STS) and malignant lymphomas (ML) which are the diagnostic groups indicated to be associated with exposure to phenoxy herbicides in the Swedish studies. Five cases of STS were observed among male employees in contrast to 1.84 expected cases. This result supports the Swedish observation of an increased risk of STS following exposure to phenoxy herbicides unlikely to be contaminated with 2,3,7,8-TCDD. However, several potential biases have to be taken into account in interpretation of this observation and these are discussed. Seven cases of ML were observed among male employees in contrast to 5.37 expected which does not support the Swedish observation of an excess risk. The total cancer risk among persons employed in manufacture and packaging of phenoxy herbicides was equivalent to the cancer risk in the Danish population. Among males thus employed 11 lung cancer cases were observed in contrast to 5.33 expected. Attention should be given to exposure to spray dried MCPA-sodium salt in the plants, but other work place exposures and tobacco consumption may have contributed to the increased risk. The tabulation of data by many diagnostic groups may explain the excesses observed for rectum cancer among males and cervical cancer among females. The study has revealed that several potential biases have to be taken into account when the Swedish observations are tested in other settings. PMID:4027168

Comparative Analysis of Two Industries for Validating Green Manufacturing (GM) Framework: An Indian Scenario

NASA Astrophysics Data System (ADS)

Rehman, Minhaj Ahemad Abdul; Shrivastava, Rakesh Lakshmikumar; Shrivastava, Rashmi Rakesh

2017-04-01

Green Manufacturing (GM) deals with manufacturing practices that reduces or eliminates the adverse environmental impact during any of its phases. It emphasizes the use of processes that do not contaminate the environment or hurt consumers, employees, or other stakeholders. This paper presents the comparative analysis of two Indian industries representing different sectors for validating GM framework. It also highlights the road map of the companies for achieving performance improvement through GM implementation and its impact on organisational performance. The case studies helps in evaluating the companies GM implementation and overall business performance. For this, a developed diagnostic instrument in the form of questionnaire was administered amongst employees in the companies respectively and their responses were analysed. In order to have a better understanding of the impact of GM implementation, the information about overall business performance was obtained over the last 3 years. The diagnostic instrument developed here may be used by manufacturing organisations to prioritise their management efforts to assess and implement GM.

Incidence of cancer and exposure to toluene diisocyanate and methylene diphenyldiisocyanate: a cohort based case-referent study in the polyurethane foam manufacturing industry.

PubMed Central

Hagmar, L; Strömberg, U; Welinder, H; Mikoczy, Z

1993-01-01

OBJECTIVE--To assess the association between occupational exposure to toluene diisocyanate or methylene diphenyldiisocyanate and risk of cancer. DESIGN--A cohort based case-referent study. STUDY BASE--7023 subjects employed during the period 1958 to 1987 in nine Swedish polyurethane foam manufacturing plants. MAIN OUTCOME MEASURES--Odds ratios adjusted with respect to the matching factors (age at risk, calendar year at risk, sex, and plant), calculated from the conditional logistic regression model. RESULTS--A non-significant association was found between high exposure to isocyanates and prostate cancer (OR 2.66, 90% confidence interval (90% CI) 0.39-18.1), which was not enhanced when an induction latency period of 10 years was applied. An association between isocyanate exposure and colon cancer was even weaker. No associations were seen for non-Hodgkin's lymphoma and rectal cancer. CONCLUSIONS--The tentative associations, derived from a previous cohort study, between isocyanate exposure and excess risk for non-Hodgkin's lymphoma and rectal cancer were not supported. Instead, non-significant associations with prostate cancer, and possibly colon cancer, were seen. PMID:8280625

Computer-Aided Design/Computer-Assisted Manufacture Monolithic Restorations for Severely Worn Dentition: A Case History Report.

PubMed

Abou-Ayash, Samir; Boldt, Johannes; Vuck, Alexander

Full-arch rehabilitation of patients with severe tooth wear due to parafunctional behavior is a challenge for dentists and dental technicians, especially when a highly esthetic outcome is desired. A variety of different treatment options and prosthetic materials are available for such a clinical undertaking. The ongoing progress of computer-aided design/computer-assisted manufacture technologies in combination with all-ceramic materials provides a predictable workflow for these complex cases. This case history report describes a comprehensive, step-by-step treatment protocol leading to an optimally predictable treatment outcome for an esthetically compromised patient.

Novel mechanism of premature battery failure due to lithium cluster formation in implantable cardioverter-defibrillators.

PubMed

Pokorney, Sean D; Greenfield, Ruth Ann; Atwater, Brett D; Daubert, James P; Piccini, Jonathan P

2014-12-01

Battery failure is an uncommon complication of implantable cardioverter-defibrillators (ICDs), but unanticipated battery depletion can have life-threatening consequences. The purpose of this study was to describe the prevalence of a novel mechanism of battery failure in St. Jude Medical Fortify and Unify ICDs. Cases of premature Fortify battery failure from a single center are reported. A search (January 1, 2010 through November 30, 2013) for Fortify and Unify premature batter failure was conducted of the Food and Drug Administration's Manufacturer and User Facility Device Experience Database (MAUDE). These findings were supplemented with information provided by St. Jude Medical. Premature battery failure for 2 Fortify ICDs in our practice were attributed to the presence of lithium clusters near the cathode, causing a short circuit and high current drain. The prevalence of this mechanism of premature battery failure was 0.6% in our practice. A MAUDE search identified 39 cases of Fortify (30) and Unify (9) premature battery depletion confirmed by the manufacturer, representing a 0.03% prevalence. Four additional Fortify and 2 Unify cases were identified in MAUDE as suspected premature battery depletion, but in these cases the pulse generator was not returned to the manufacturer for evaluation. St. Jude Medical identified 10 cases of premature battery failure due to lithium clusters in Fortify devices (9) and Unify devices (1), representing a 0.004% prevalence. The deposition of lithium clusters near the cathode is a novel mechanism of premature battery failure. The prevalence of this problem is unknown. Providers should be aware of this mechanism for patient management. Copyright © 2014 Heart Rhythm Society. Published by Elsevier Inc. All rights reserved.

Hybrid and disposable facilities for manufacturing of biopharmaceuticals: pros and cons.

PubMed

Ravisé, Aline; Cameau, Emmanuelle; De Abreu, Georges; Pralong, Alain

2009-01-01

Modern biotechnology has grown over the last 35 years to a maturing industry producing and delivering high-value biopharmaceuticals that yield important medical and economical benefits. The constantly increasing need for biopharmaceuticals and significant costs related to time-consuming R&D work makes this industry risky and highly competitive. This trend is confirmed by the important number of biopharmaceuticals that are actually under development at all stages by all major pharmaceutical industry companies. A consequence of this evolution is an increasing need for development and manufacturing capacity. The build up of traditional - stainless steel - technology is complicated, time consuming and very expensive. The decision for such a major investment needs to be taken early in the development cycle of a promising drug to cope with future demands for clinical trials and product launch. Possibilities for the reduction of R&D and manufacturing costs are therefore of significant interest in order to be competitive.In this chapter, four case studies are presented which outline ways to reduce significantly R&D and manufacturing costs by using disposable technology in the frame of a the transfer of an antibody manufacturing process, the preparation of media and buffers in commercial manufacturing and a direct comparison of a traditional and a fully disposable pilot plant.

The use of Tecnomatix software to simulate the manufacturing flows in an industrial enterprise producing hydrostatic components

NASA Astrophysics Data System (ADS)

Petrila, S.; Brabie, G.; Chirita, B.

2016-08-01

The analysis performed on manufacturing flows within industrial enterprises producing hydrostatic components twos made on a number of factors that influence smooth running of production such: distance between pieces, waiting time from one surgery to another; time achievement of setups on CNC machines; tool changing in case of a large number of operators and manufacturing complexity of large files [2]. To optimize the manufacturing flow it was used the software Tecnomatix. This software represents a complete portfolio of manufacturing solutions digital manufactured by Siemens. It provides innovation by linking all production methods of a product from process design, process simulation, validation and ending the manufacturing process. Among its many capabilities to create a wide range of simulations, the program offers various demonstrations regarding the behavior manufacturing cycles. This program allows the simulation and optimization of production systems and processes in several areas such as: car suppliers, production of industrial equipment; electronics manufacturing, design and production of aerospace and defense parts.

Making the Case for a Model-Based Definition of Engineering Materials (Postprint)

DTIC Science & Technology

2017-09-12

MBE relies on digi- tal representations, or a model-based definition (MBD), to define a product throughout design , manufacturing and sus- tainment...discovery through development, scale-up, product design and qualification, manufacture and sustainment have changed little over the past decades. This...testing data provided a certifiable material definition, so as to minimize risk and simplify procurement of materials during the design , manufacture , and

Job Rotation Designed to Prevent Musculoskeletal Disorders and Control Risk in Manufacturing Industries: A Systematic Review

PubMed Central

Padula, Rosimeire Simprini; Comper, Maria Luiza Caires; Sparer, Emily H.; Dennerlein, Jack T

2017-01-01

To better understand job rotation in the manufacturing industry, we completed a systematic review asking the following questions: 1) How do job-rotation programs impact work-related musculoskeletal disorders (MSDs) and related risk control for these MSDs, as well as psychosocial factors? and 2) How best should the job rotation programs be designed? We searched MEDLINE, EMBASE, Business Source Premier, ISI Web of Knowledge, CINAHL, PsyINFO, Scopus, and SciELO databases for articles published in peer-reviewed journals. Eligible studies were examined by two independent reviewers for relevance (population of manufacturing workers, outcomes of musculoskeletal disease, physical factors, psychosocial factors, and strategies used in job-rotation implantation) and methodological quality rating. From 10,809 potential articles, 71 were read for full text analysis. Of the 14 studies included for data extraction, two were non-randomized control trial studies, one was a case-control study, and 11 were cross-sectional comparisons. Only one, with a case-control design, was scored with good methodological quality. Currently, weak evidence exists supporting job rotation as a strategy for the prevention and control of musculoskeletal disorders. Job rotation did not appear to reduce the exposure of physical risk factors; yet, there are positive correlations between job rotation and higher job satisfaction. Worker training has been described as a crucial component of a successful job-rotation program. The studies reported a range of parameters used to implement and measure job-rotation programs. More rigorous studies are needed to better understand the full impact of job rotation on production and health. PMID:27633235

CASE-COHORT STUDY OF STYRENE EXPOSURE AND ISCHEMIC HEART DISEASE INVESTIGATORS

EPA Science Inventory

Investigators examined workers exposed to styrene while working in styrene-butadiene polymer manufacturing plants between 1943 and 1982. Workers who had died from ischemic heart disease were compared to a subgroup of all men employed in two styrene-butadiene polymer manufac...

SOLVENT-BASED TO WATERBASED ADHESIVE-COATED SUBSTRATE RETROFIT - VOLUME I: COMPARATIVE ANALYSIS

EPA Science Inventory

This volume represents the analysis of case study facilities' experience with waterbased adhesive use and retrofit requirements. (NOTE: The coated and laminated substrate manufacturing industry was selected as part of NRMRL'S support of the 33/50 Program because of its significan...

Information Society and the Transformation of Organizations in Finland.

ERIC Educational Resources Information Center

Blom, Raimo; Melin, Harri

2003-01-01

Case studies of three Finnish companies (involved in manufacturing, Internet catalogs, and municipal government services) were used to investigate the nature of organizational change. Significant differences among organizational types were apparent in team formation, pay systems, recruitment, and forms of control. Organization differences reflect…

Safety of plant-made pharmaceuticals: product development and regulatory considerations based on case studies of two autologous human cancer vaccines.

PubMed

Tusé, Daniel

2011-03-01

Guidelines issued by regulatory agencies for the development of plant-made pharmaceutical (PMP) products provide criteria for product manufacturing and characterization, safety determination, containment and mitigation of environmental risks. Features of plant-made products do not always enable an easy fit within the criteria subscribed to by regulators. The unconventional nature of plant-based manufacturing processes and peculiarities of plant biology relative to that of traditional biological production systems have led to special considerations in the regulatory scrutiny of PMP. Presented in this review are case studies of two plant-made autologous (patient-specific) cancer vaccines, the nature of which introduced challenges to conventional and standardized development and preclinical evaluation routes. The rationale presented to FDA by the sponsors of each vaccine to build consensus and obtain variances to existing guidelines is discussed. While development of many plant-made biologics can be accomplished within the existing regulatory framework, the development of specialized products can be defended with rational arguments based on strong science.

Case study of fly ash brick manufacturing units at Kota in Rajasthan

NASA Astrophysics Data System (ADS)

Sharma, Y.; Saxena, B. K.; Rao, K. V. S.

2018-03-01

Kota Super Thermal Power Station of 1240 MW is located at Kota in Rajasthan, India. The quantity of fly ash generated by it is about 1.64 to 2.03 million tonnes per year. This fly ash is being utilized for making bricks, tiles, portland pozzolana cement, construction of highways, and other purposes. 1.79 million tonnes of fly ash was utilized for different applications in one year duration from April 01st, 2015 to March 31st, 2016. Out of this total utilization, 0.6439 million tonnes (36.06 %) of fly ash was used for making bricks, blocks, and tiles. In this paper, a case study of two fly ash brick manufacturing units using fly ash produced from Kota Super Thermal Power Station is described. These units produce about 15,000 and 20,000 bricks respectively by employing 10 and 16 workers each and are making a profit of about Rs. 6,000 and Rs. 8,000 per day in one shift.

Supply chain value creation methodology under BSC approach

NASA Astrophysics Data System (ADS)

Golrizgashti, Seyedehfatemeh

2014-06-01

The objective of this paper is proposing a developed balanced scorecard approach to measure supply chain performance with the aim of creating more value in manufacturing and business operations. The most important metrics have been selected based on experts' opinion acquired by in-depth interviews focused on creating more value for stakeholders. Using factor analysis method, a survey research has been used to categorize selected metrics into balanced scorecard perspectives. The result identifies the intensity of correlation between perspectives and cause-and-effect chains among them using statistical method based on a real case study in home appliance manufacturing industries.

Detecting Nano-Scale Vibrations in Rotating Devices by Using Advanced Computational Methods

PubMed Central

del Toro, Raúl M.; Haber, Rodolfo E.; Schmittdiel, Michael C.

2010-01-01

This paper presents a computational method for detecting vibrations related to eccentricity in ultra precision rotation devices used for nano-scale manufacturing. The vibration is indirectly measured via a frequency domain analysis of the signal from a piezoelectric sensor attached to the stationary component of the rotating device. The algorithm searches for particular harmonic sequences associated with the eccentricity of the device rotation axis. The detected sequence is quantified and serves as input to a regression model that estimates the eccentricity. A case study presents the application of the computational algorithm during precision manufacturing processes. PMID:22399918

A case study on Measurement of Degree of Performance of an Industry by using Lean Score Technique

NASA Astrophysics Data System (ADS)

Srinivasa Rao, P.; Niraj, Malay

2016-09-01

Lean manufacturing concept is becoming a very important strategy for both academicians and practitioners in the recent times, and Japanese are using this practice for more than a decade. In this present scenario, this paper describes an innovative approach for lean performance evaluation by using fuzzy membership functions before and after implementing lean manufacturing techniques and formulating a model to establish the lean score through the lean attributes by eliminating major losses. It shows a systematic lean performance measurement by producing a final integrated unit less-score.

Effectiveness of the live attenuated rotavirus vaccine produced by a domestic manufacturer in China studied using a population-based case-control design.

PubMed

Zhen, Shan-Shan; Li, Yue; Wang, Song-Mei; Zhang, Xin-Jiang; Hao, Zhi-Yong; Chen, Ying; Wang, Dan; Zhang, Yan-Hong; Zhang, Zhi-Yong; Ma, Jing-Chen; Zhou, Peng; Zhang, Zhen; Jiang, Zhi-Wei; Zhao, Yu-Liang; Wang, Xuan-Yi

2015-10-01

A universal rotavirus (RV) immunization program is a potentially cost-effective measure for preventing RV infection in China. However, the efficacy of the only licensed RV vaccine (Lanzhou lamb rotavirus vaccine, LLR), which is made by a domestic manufacturer, has not been proven by a properly designed clinical trial. In October 2011 to March 2012, to measure the potential protection provided by LLR, a case-control study nested in a population-based active diarrhea surveillance study of children <5 years of age was conducted in rural Zhengding county. During the study period, 308 episodes of diarrhea were identified as being caused by RV infection, resulting in an incidence rate of 48.0/1000 people/year. The predominant RV serotype was G3 (61.5%), followed by G1 (15.2%), and G9 (6.5%). Overall, a protection of 35.0% (95% confidence interval (CI), 13.0%-52.0%) was identified, and higher protection was found among moderate RV gastroenteritis cases caused by the serotype G3 (52.0% 95% CI: 2.0%-76.1%). A concurrently conducted case-control study comparing non-RV viral diarrheal cases with non-diarrheal controls in the same population found that the RV vaccine offered no protection against non-RV diarrhea. Even under a less ideal immunization schedule, the oral LLR conferred a certain level of protection against RV gastroenteritis. However, further studies are needed to understand the full characteristics of the LLR, including its efficacy when administered following the optimal regimen, the potential risk of inducing intussusception, and the direct and indirect protective effects of LLR.

Affordability and availability of off-patent drugs in the United States—the case for importing from abroad: observational study

PubMed Central

Gupta, Ravi; Bollyky, Thomas J; Cohen, Matthew; Ross, Joseph S

2018-01-01

Abstract Objectives To evaluate whether off-patent prescription drugs at risk of sudden price increases or shortages in the United States are available from independent manufacturers approved in other well regulated settings around the world. Design Observational study. Setting Off-patent drugs in the USA and approved by the Food and Drug Administration, up to 10 April 2017. Study cohort Novel tablet or capsule prescription drugs approved by the FDA since 1939 that were no longer protected by patents or other market exclusivity and had up to three generic versions. Main outcome measures Number of additional manufacturers that had obtained approval from any of seven non-US regulators with similar standards (European Medicines Agency (European Union), HealthCanada (Canada), Therapeutic Goods Association (Australia), Medsafe (New Zealand), Swissmedic (Switzerland), Medicines Control Council (South Africa), and the Israel Health Ministry). Association with drug characteristics including US orphan drug designation for drugs treating rare diseases, World Health Organization essential medicine designation, treatment area, drug product complexity (that is, with attributes that could complicate establishing bioequivalence or manufacturing), and total Medicaid spending in 2015. Results Of 170 eligible study drugs, more than half (109, 64%) had at least one manufacturer approved by a non-US regulator and 32 (19%) had four or more. Among 44 (26%) drugs with no FDA approved generic versions, 21 (48%) were available from at least one manufacturer approved by one of the seven non-US regulators, and two (5%) by four or more manufacturers. Across all drugs and regulators (including the FDA), 66 (39%) drugs were available from four or more total manufacturers. Of 109 drugs with at least one non-US regulator approved manufacturer, 12 (11%) were approved for patients with rare diseases and 29 (27%) were WHO designated essential medicines; only 12 (11%) were complex products that might be more complicated to import. The highest numbers of drugs were indicated for treating cardiovascular diseases, diabetes, or hyperlipidemia (19, 17%); psychiatric disease (16, 15%); and infectious diseases (15, 14%). In 2015, Medicaid alone spent nearly US$700m (£508m; €570m) on generic drugs without adequate US competition that could have had a manufacturer approved by non-US peer regulatory agencies. Conclusion In this study, more than half the off-patent drugs with no generic competition in the USA had at least one independent manufacturer approved by a non-US peer regulatory agency; slightly fewer than half had four or more total manufacturers. Facilitating US patient access to such manufacturers could help sustain affordable access to essential off-patent drugs. PMID:29555641

24 CFR 50.17 - Decision points for projects.

Code of Federal Regulations, 2013 CFR

2013-04-01

... (including sections 202 and 811), nursing homes, hospitals, group practice facilities and manufactured home... Disposition. Multifamily structures, college housing, nursing homes, manufactured homes and parks, group.... (e) HUD programs subject to 24 CFR part 58. For cases in which HUD exercises environmental...

24 CFR 50.17 - Decision points for projects.

Code of Federal Regulations, 2014 CFR

2014-04-01

... (including sections 202 and 811), nursing homes, hospitals, group practice facilities and manufactured home... Disposition. Multifamily structures, college housing, nursing homes, manufactured homes and parks, group.... (e) HUD programs subject to 24 CFR part 58. For cases in which HUD exercises environmental...

24 CFR 50.17 - Decision points for projects.

Code of Federal Regulations, 2011 CFR

2011-04-01

... (including sections 202 and 811), nursing homes, hospitals, group practice facilities and manufactured home... Disposition. Multifamily structures, college housing, nursing homes, manufactured homes and parks, group.... (e) HUD programs subject to 24 CFR part 58. For cases in which HUD exercises environmental...

An updated investigation of cancer incidence and mortality at a Scottish semiconductor manufacturing facility with case-control and case-only studies of selected cancers.

PubMed

Darnton, Andrew; Miller, Brian G; Maccalman, Laura; Galea, Karen S; Wilkinson, Sam; Cherrie, John W; Shafrir, Amy; McElvenny, Damien; Osman, John

2012-10-01

An earlier investigation raised concern that some cancer cases might be linked to work at a semiconductor manufacturing plant. The aim of this study was to describe an update of the cancer incidence and mortality of these workers and assess whether workplace exposures contributed to any increased risk of selected cancers. Standardised mortality ratios and standardised incidence ratios were calculated for cancer site groups of a priori interest in a cohort previously flagged against the National Health Service Central Register, with follow-up extended to the 2007 for deaths and 2006 for cancer registrations. Cases of female breast cancer, lung and stomach cancer, and male brain cancer, and a random sample of control subjects individually age-matched to the breast cancer cases, were identified from within the cohort dataset and invited to participate via general practitioners. Exposures were estimated using a job exposure matrix developed from a historical hygiene assessment and assigned to job histories obtained from personal interview of subjects (or proxies). Though the findings were uncertain, there were no excesses of mortality or cancer incidence, either overall or for specific cancer sites, suggestive of a workplace effect. Logistic regression analyses comparing 20 cases of breast cancer with 83 matched controls showed no consistent evidence of any relationship with occupational exposures. Assessment of commonalities of workplace exposures among case sets for other cancer types was limited by the small numbers. These results do not support earlier concerns about occupational cancer risks among this cohort.

Evaluation of an Al-Ce alloy for laser additive manufacturing

DOE PAGES

Plotkowski, A.; Rios, O.; Sridharan, N.; ...

2016-12-27

Our present research in metal additive manufacturing (AM) focuses on designing processing parameters around existing alloys designed for traditional manufacturing. However, to maximize the benefits of AM, alloys should be designed to specifically take advantage of the unique thermal conditions of these processes. Furthermore, our study focuses on the development of a design methodology for alloys in AM, using a newly developed Al-Ce alloy as an initial case study. To evaluate the candidacy of this system for fusion based additive manufacturing, single-line laser melts were made on cast Al-12Ce plates using three different beam velocities (100, 200, and 300 mm/min).more » The microstructure was evaluated in the as-melted and heat treated conditions (24 hrs at 300°C). An extremely fine microstructure was observed within the weld pools, evolving from eutectic at the outer solid-liquid boundaries to a primary Al FCC dendritic/cellular structure nearer the melt-pool centerline. We rationalized the observed microstructures through the construction of a microstructure selection map for the Al-Ce binary system, which will be used to enable future alloy design. Interestingly, the heat treated samples exhibited no microstructural coarsening.« less

Drivers and barriers to e-invoicing adoption in Greek large scale manufacturing industries

NASA Astrophysics Data System (ADS)

Marinagi, Catherine; Trivellas, Panagiotis; Reklitis, Panagiotis; Skourlas, Christos

2015-02-01

This paper attempts to investigate the drivers and barriers that large-scale Greek manufacturing industries experience in adopting electronic invoices (e-invoices), based on three case studies with organizations having international presence in many countries. The study focuses on the drivers that may affect the increase of the adoption and use of e-invoicing, including the customers demand for e-invoices, and sufficient know-how and adoption of e-invoicing in organizations. In addition, the study reveals important barriers that prevent the expansion of e-invoicing, such as suppliers' reluctance to implement e-invoicing, and IT infrastructures incompatibilities. Other issues examined by this study include the observed benefits from e-invoicing implementation, and the financial priorities of the organizations assumed to be supported by e-invoicing.

Emission factors of air toxics from semiconductor manufacturing in Korea.

PubMed

Eom, Yun-Sung; Hong, Ji-Hyung; Lee, Suk-Jo; Lee, Eun-Jung; Cha, Jun-Seok; Lee, Dae-Gyun; Bang, Sun-Ae

2006-11-01

The development of local, accurate emission factors is very important for the estimation of reliable national emissions and air quality management. For that, this study is performed for pollutants released to the atmosphere with source-specific emission tests from the semiconductor manufacturing industry. The semiconductor manufacturing industry is one of the major sources of air toxics or hazardous air pollutants (HAPs); thus, understanding the emission characteristics of the emission source is a very important factor in the development of a control strategy. However, in Korea, there is a general lack of information available on air emissions from the semiconductor industry. The major emission sources of air toxics examined from the semiconductor manufacturing industry were wet chemical stations, coating applications, gaseous operations, photolithography, and miscellaneous devices in the wafer fabrication and semiconductor packaging processes. In this study, analyses of emission characteristics, and the estimations of emission data and factors for air toxics, such as acids, bases, heavy metals, and volatile organic compounds from the semiconductor manufacturing process have been performed. The concentration of hydrogen chloride from the packaging process was the highest among all of the processes. In addition, the emission factor of total volatile organic compounds (TVOCs) for the packaging process was higher than that of the wafer fabrication process. Emission factors estimated in this study were compared with those of Taiwan for evaluation, and they were found to be of similar level in the case of TVOCs and fluorine compounds.

Comparison of the class and individual characteristics of Turkish 7.65 mm Browning/.32 Automatic caliber self-loading pistols with consecutive serial numbers.

PubMed

Sarıbey, Aylin Yalçin; Hannam, Abigail Grace

2013-01-01

Firearms identification is based on the fundamental principle that it is impossible to manufacture two identical items at the microscopic level. As firearm manufacturing technologies and quality assurance are improving, it is necessary to continually challenge this principle. In this study, two different makes of 7.65 mm Browning/.32 Automatic caliber self-loading pistols of Turkish manufacture were selected and examined. Ten pistols with consecutive serial numbers were examined and each fired 10 times. The fired cartridge cases were recovered for comparison purposes. It was found that for each make of pistol, the individual characteristics within the firing pin impression, ejector, and breech face marks of all 10 pistols were found to be significantly different. © 2012 American Academy of Forensic Sciences.

Advances in the manufacturing, types, and applications of biosensors

NASA Astrophysics Data System (ADS)

Ravindra, Nuggehalli M.; Prodan, Camelia; Fnu, Shanmugamurthy; Padronl, Ivan; Sikha, Sushil K.

2007-12-01

In recent years, there have been significant technological advancements in the manufacturing, types, and applications of biosensors. Applications include clinical and non-clinical diagnostics for home, bio-defense, bio-remediation, environment, agriculture, and the food industry. Biosensors have progressed beyond the detection of biological threats such as anthrax and are finding use in a number of non-biological applications. Emerging biosensor technologies such as lab-on-a-chip have revolutionized the integration approaches for a very flexible, innovative, and user-friendly platform. An overview of the fundamentals, types, applications, and manufacturers, as well as the market trends of biosensors is presented here. Two case studies are discussed: one focused on a characterization technique—patch clamping and dielectric spectroscopy as a biological sensor—and the other about lithium phthalocyanine, a material that is being developed for in-vivo oxymetry.

Falcon: Visual analysis of large, irregularly sampled, and multivariate time series data in additive manufacturing

DOE PAGES

Steed, Chad A.; Halsey, William; Dehoff, Ryan; ...

2017-02-16

Flexible visual analysis of long, high-resolution, and irregularly sampled time series data from multiple sensor streams is a challenge in several domains. In the field of additive manufacturing, this capability is critical for realizing the full potential of large-scale 3D printers. Here, we propose a visual analytics approach that helps additive manufacturing researchers acquire a deep understanding of patterns in log and imagery data collected by 3D printers. Our specific goals include discovering patterns related to defects and system performance issues, optimizing build configurations to avoid defects, and increasing production efficiency. We introduce Falcon, a new visual analytics system thatmore » allows users to interactively explore large, time-oriented data sets from multiple linked perspectives. Falcon provides overviews, detailed views, and unique segmented time series visualizations, all with adjustable scale options. To illustrate the effectiveness of Falcon at providing thorough and efficient knowledge discovery, we present a practical case study involving experts in additive manufacturing and data from a large-scale 3D printer. The techniques described are applicable to the analysis of any quantitative time series, though the focus of this paper is on additive manufacturing.« less

Falcon: Visual analysis of large, irregularly sampled, and multivariate time series data in additive manufacturing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steed, Chad A.; Halsey, William; Dehoff, Ryan

Flexible visual analysis of long, high-resolution, and irregularly sampled time series data from multiple sensor streams is a challenge in several domains. In the field of additive manufacturing, this capability is critical for realizing the full potential of large-scale 3D printers. Here, we propose a visual analytics approach that helps additive manufacturing researchers acquire a deep understanding of patterns in log and imagery data collected by 3D printers. Our specific goals include discovering patterns related to defects and system performance issues, optimizing build configurations to avoid defects, and increasing production efficiency. We introduce Falcon, a new visual analytics system thatmore » allows users to interactively explore large, time-oriented data sets from multiple linked perspectives. Falcon provides overviews, detailed views, and unique segmented time series visualizations, all with adjustable scale options. To illustrate the effectiveness of Falcon at providing thorough and efficient knowledge discovery, we present a practical case study involving experts in additive manufacturing and data from a large-scale 3D printer. The techniques described are applicable to the analysis of any quantitative time series, though the focus of this paper is on additive manufacturing.« less

Opportunities and challenges of real-time release testing in biopharmaceutical manufacturing.

PubMed

Jiang, Mo; Severson, Kristen A; Love, John Christopher; Madden, Helena; Swann, Patrick; Zang, Li; Braatz, Richard D

2017-11-01

Real-time release testing (RTRT) is defined as "the ability to evaluate and ensure the quality of in-process and/or final drug product based on process data, which typically includes a valid combination of measured material attributes and process controls" (ICH Q8[R2]). This article discusses sensors (process analytical technology, PAT) and control strategies that enable RTRT for the spectrum of critical quality attributes (CQAs) in biopharmaceutical manufacturing. Case studies from the small-molecule and biologic pharmaceutical industry are described to demonstrate how RTRT can be facilitated by integrated manufacturing and multivariable control strategies to ensure the quality of products. RTRT can enable increased assurance of product safety, efficacy, and quality-with improved productivity including faster release and potentially decreased costs-all of which improve the value to patients. To implement a complete RTRT solution, biologic drug manufacturers need to consider the special attributes of their industry, particularly sterility and the measurement of viral and microbial contamination. Continued advances in on-line and in-line sensor technologies are key for the biopharmaceutical manufacturing industry to achieve the potential of RTRT. Related article: http://onlinelibrary.wiley.com/doi/10.1002/bit.26378/full. © 2017 Wiley Periodicals, Inc.

Can managed care organizations partner with manufacturers for comparative effectiveness research?

PubMed

Luce, Bryan R; Paramore, L Clark; Parasuraman, Bhash; Liljas, Bengt; de Lissovoy, Gregory

2008-03-01

To describe 2 published pragmatic or practical clinical trials (PCTs) as case studies illustrating successful partnerships between managed care organizations (MCOs) and pharmaceutical manufacturers. In today's environment, there is increasing concern about the comparative effectiveness of medical interventions. Various opinion leaders and stakeholders lament the dearth of such evidence and are calling for the public and private sectors to invest up to billions of dollars to create better comparative evidence. We selected 2 PCTs conducted at different points in the drug life cycle to highlight strengths, limitations, and policy implications. The phase IV study compared fluoxetine hydrochloride vs 2 generic tricyclic antidepressants in selected primary care clinics of a health maintenance organization from 1992 through 1994. The phase IIIb study compared daily budesonide via dry powder inhaler vs triamcinolone acetonide metered-dose inhaler in adult patients with persistent asthma in 25 MCOs from 1995 through 1998. Both PCTs were successfully sponsored and funded by pharmaceutical manufacturers in collaboration with MCOs and provided potentially useful evidence of real-world effectiveness and evidence of value to healthcare decision makers. Industry-sponsored PCTs in managed care are feasible when manufacturer and MCO incentives align and can provide real-world evidence of comparative effectiveness and value for money. These trials can be conducted successfully in the phase IIIb and phase IV environments.

Mirror-Imaged Rapid Prototype Skull Model and Pre-Molded Synthetic Scaffold to Achieve Optimal Orbital Cavity Reconstruction.

PubMed

Park, Sung Woo; Choi, Jong Woo; Koh, Kyung S; Oh, Tae Suk

2015-08-01

Reconstruction of traumatic orbital wall defects has evolved to restore the original complex anatomy with the rapidly growing use of computer-aided design and prototyping. This study evaluated a mirror-imaged rapid prototype skull model and a pre-molded synthetic scaffold for traumatic orbital wall reconstruction. A single-center retrospective review was performed of patients who underwent orbital wall reconstruction after trauma from 2012 to 2014. Patients were included by admission through the emergency department after facial trauma or by a tertiary referral for post-traumatic orbital deformity. Three-dimensional (3D) computed tomogram-based mirror-imaged reconstruction images of the orbit and an individually manufactured rapid prototype skull model by a 3D printing technique were obtained for each case. Synthetic scaffolds were anatomically pre-molded using the skull model as guide and inserted at the individual orbital defect. Postoperative complications were assessed and 3D volumetric measurements of the orbital cavity were performed. Paired samples t test was used for statistical analysis. One hundred four patients with immediate orbital defect reconstructions and 23 post-traumatic orbital deformity reconstructions were included in this study. All reconstructions were successful without immediate postoperative complications, although there were 10 cases with mild enophthalmos and 2 cases with persistent diplopia. Reoperations were performed for 2 cases of persistent diplopia and secondary touchup procedures were performed to contour soft tissue in 4 cases. Postoperative volumetric measurement of the orbital cavity showed nonsignificant volume differences between the damaged orbit and the reconstructed orbit (21.35 ± 1.93 vs 20.93 ± 2.07 cm(2); P = .98). This protocol was extended to severe cases in which more than 40% of the orbital frame was lost and combined with extensive soft tissue defects. Traumatic orbital reconstruction can be optimized and successful using an individually manufactured rapid prototype skull model and a pre-molded synthetic scaffold by computer-aid design and manufacturing. Copyright © 2015 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Developing an experimental case in aluminium foils 1100 to determine the maximum angle of formability in a piece by Dieless-SPIF process

NASA Astrophysics Data System (ADS)

Gabriel, Paramo; Adrian, Benitez

2014-07-01

Incremental sheet forming by the method of single point incremental forming Dieless-SPIF, is a widely studied process, experimented and developed in countries with high manufacturing technologies, with friendly costs when the productive configuration in a productivity system is based in small production batches. United states, United kingdom and France lead this type of studies and cases, developing various proof with experimental geometries, different from the national environment such as Colombia, Bolivia, Chile, Ecuador and Peru where this process where discretely studied. Previously mentioned, it pretends develop an experimental case of a particular geometry, identifying the maximum formability angle of material permissible for the forming of a piece in one pass, the analysis of forming limit curve (FLC), with the objective to emphasizes in this innovative method based in CAD-CAM technologies, compare with other analogous process of deformation sheet metal like embossing, take correct decisions about the viability and applicability of this process (Dieless) in a particular industrial piece, which responses to the necessities of productive configurations mentioned and be highly taken like a manufacturing alternative to the other conventional process of forming sheet metal like embossing, for systems with slow batches production.

Comprehensive Mass Analysis for Chemical Processes, a Case Study on L-Dopa Manufacture

EPA Science Inventory

To evaluate the “greenness” of chemical processes in route selection and process development, we propose a comprehensive mass analysis to inform the stakeholders from different fields. This is carried out by characterizing the mass intensity for each contributing chemical or wast...

E3 Success Story - San Antonio E3 Case Study: UEMC “Now Hiring”

EPA Pesticide Factsheets

exas Manufacturing Assistance Center conducted an E3 assessment as part of the local Lean-Clean-Energy program in October of 2009. Overall, UEMC has reduced demand by approximately 30kw and reduced consumption by over 100,000 kwh/year.

An Architecture for Learning in Projects?

ERIC Educational Resources Information Center

Sense, Andrew J.

2004-01-01

This paper reports upon a two-year, qualitative, case study action research investigation into "learning within a project team". This project team undertook a significant socio-technical redesign project within a major Australian heavy engineering/manufacturing operation. The paper identifies and elaborates upon a number of elements that…

Whether Foreign Military Sales or Direct Commercial Sales: A Case Study of the UK E-3 AWACS

DTIC Science & Technology

1990-09-01

arrangements available include coproduction, licensed production, subcontractor production, overseas investment, technology transfer, and countertrade ...commercial arrangement between the U.S. manufacturer and a foreign entity. Countertrade - Purchase of goods and services from the buyer country as a

Ahmad Mayyas | NREL

Science.gov Websites

University-International Center for Automotive Research (CU-ICAR) (2009-2012) Intern/Reliability Engineer selection for body-in-white." International Journal of Sustainable Manufacturing 2, no. 4 (August 2012 Structure Case Study." Accepted for publication in International Journal of Sustainable Engineering

Annual Expeditionary Warfare Conference (22nd)

DTIC Science & Technology

2017-10-24

for many copies of data and a unique software stack to operate on it. PSI designs and manufactures shipping and carrying cases as well as providing...An ISO 9001:2008 rated company, Trijicon Inc., is committed to Customer Satisfaction through the design , development, and manufacture of superior...their endeavors to continue as a world leader in the design and manufacture of high quality, innovative sighting systems. TABLE TOP dISPLAyErS 12 LtGen

Models for formation and choice of variants for organizing digital electronics manufacturing

NASA Astrophysics Data System (ADS)

Korshunov, G. I.; Lapkova, M. Y.; Polyakov, S. L.; Frolova, E. A.

2018-03-01

The directions of organizing digital electronics manufacturing are considered by the example of surface mount technology. The basic equipment choice has to include not only individual characteristics, but also mutual influence of individual machines and the results of design for manufacturing. Application of special cases of the Utility function which are complicated in the general representation of polynomial functions are proposed for estimation of product quality in a staged automation.

A descriptive study of work aggravated asthma.

PubMed

Goe, S K; Henneberger, P K; Reilly, M J; Rosenman, K D; Schill, D P; Valiante, D; Flattery, J; Harrison, R; Reinisch, F; Tumpowsky, C; Filios, M S

2004-06-01

Work related asthma (WRA) is one of the most frequently reported occupational lung diseases in a number of industrialised countries. A better understanding of work aggravated asthma (WAA), as well as work related new onset asthma (NOA), is needed to aid in prevention efforts. WAA and NOA in the United States were compared using cases reported to the National Institute for Occupational Safety and Health (NIOSH) from four state Sentinel Event Notification Systems for Occupational Risks (SENSOR) surveillance programmes for 1993-95. A total of 210 WAA cases and 891 NOA cases were reported. WAA cases reported mineral and inorganic dusts as the most common exposure agent, as opposed to NOA cases, in which diisocyanates were reported most frequently. A similar percentage of WAA and NOA cases still experienced breathing problems at the time of the interview or had visited a hospital or emergency room for work related breathing problems. NOA cases were twice as likely to have applied for workers' compensation compared with WAA cases. However, among those who had applied for worker compensation, approximately three-fourths of both WAA and NOA cases had received awards. The services and manufacturing industrial categories together accounted for the majority of both WAA (62%) and NOA (75%) cases. The risk of WAA, measured by average annual rate, was clearly the highest in the public administration (14.2 cases/10(5)) industrial category, while the risk of NOA was increased in both the manufacturing (3.2 cases/10(5)) and public administration (2.9 cases/10(5)) categories. WAA cases reported many of the same adverse consequences as NOA cases. Certain industries were identified as potential targets for prevention efforts based on either the number of cases or the risk of WAA and NOA.

Decreasing incidence of cutaneous chemical burns in a resource limited burn centre: is this a positive effect of modernization?

PubMed

Nnabuko, R E E; Okoye, C P; Ogbonnaya, I S; Isiwele, Egi

2017-01-01

Burns present a devastating injury to patients. Burns caused by chemical agents, present a worse scenario. In a resource limited country like Nigeria, readily available sources of these corrosive agents are mainly from lead-acid battery vendors and to some extent local small scale soap manufacturers who use caustic soda. We hypothesized that with the reduction in small scale soap manufacturing and increasing trend towards modernization in the use of dry cell batteries, chemical burns may be on the decline, and we sought to investigate this. The records of all acute burn patients seen at the Burns and Plastic Department of the National Orthopaedic Hospital Enugu Nigeria between January 2011 and December 2014 were retrospectively reviewed. The results were compared to similar studies carried out at the same centre. A questionnaire was administered to corrosive chemical (sulphuric and caustic soda) vendors to assess the trends in product sales and use in recent times. A total of 624 acute burn cases were treated during the period; among which, 12 cases (1.9%) were chemical burns. When compared with previous studies at the centre, Chemical burn cases were  recorded as the lowest rate. The median age of patients was 24 years. There were eight males and four females. Interpersonal assault was the commonest mechanism of injury with sulphuric acid suspected to be the commonest agent in 83.3% of the cases, while 16.7% of the cases were from accidental use of caustic soda. The head and neck as well as the upper limbs were the most affected (30%). Twenty-six questionnaires to lead-acid vendors were analyzed and revealed that all respondents noticed a marked downward trend in the sale of either sulphuric acid or caustic soda, and they attributed this to the ready availability of imported alternatives to locally manufactured soap or wet lead-acid batteries. Ease of use, durability and convenience of the dry cell batteries were cited as principal reasons. There appears to be a downward trend in the prevalence of chemical burns in our study compared to previous studies in the centre which may be due to reduced availability and access of corrosive chemicals to the general public. Further prospective multicentre studies to confirm this are recommended.

North Country Successes: Case Studies of Successful Entrepreneurs in the ANCA Region.

ERIC Educational Resources Information Center

Chugh, Ram L.; Gandhi, Prem P.

This study identifies the characteristics of both successful small businesses and their entrepreneurial owners in a 14-county area of the Adirondack North Country Association (ANCA). Of the 100 survey respondents representing successful small businesses, 50% had been in business for less than 14 years; 38% were in manufacturing; 48% employed more…

Training in the Retail Trade in Portugal. Report for the FORCE Programme. Retail Sector.

ERIC Educational Resources Information Center

Cerdeira, Maria Conceicao; And Others

A study examined training in the retail trade in Portugal. Employment, work, and training patterns in Portugal's retail sector were researched, and case studies of two firms in the supermarket/hypermarket group, one firm in the stationary/cigarette shop sector, and one clothing manufacturer/retailer were conducted. Teams of researchers interviewed…

Workplace Education Efforts in Small Business: Learning from the Field. Final Report.

ERIC Educational Resources Information Center

Vencill, Mary P.; And Others

A study identified and conducted onsite case studies of 18 different education programs conducted by small companies. Two-thirds of them were conducted by manufacturing companies; the remainder were in health services, construction, or transportation companies. Most of the programs served fewer than 25 workers and had been in operation for less…

How Newcomers Learn the Social Norms of an Organization: A Case Study of the Socialization of Newly Hired Engineers

ERIC Educational Resources Information Center

Korte, Russell F.

2009-01-01

Current scholarship views organizational socialization as a learning process that is primarily the responsibility of the newcomer. Yet recent learning research recognizes the importance of the social interactions in the learning process. This study investigated how newly hired engineers at a large manufacturing company learned job-related tasks…

Determinants of the Satisfaction of Firms with the Competencies of University Students: A Spanish Case Study

ERIC Educational Resources Information Center

Marzo-Navarro, Mercedes; Pedraja-Iglesias, Marta; Rivera-Torres, Pilar

2008-01-01

In recognition of its increasing importance, many organizations make periodic assessments of their training and development activity. The objective of the present study was to extend the concept of capacity building to the assessment of training and development activity in an automobile component manufacturing organization, using a developed and…

Capacity Building as a Tool for Assessing Training and Development Activity: An Indian Case Study

ERIC Educational Resources Information Center

Krishnaveni, R.; Sripirabaa, B.

2008-01-01

In recognition of its increasing importance, many organizations make periodic assessments of their training and development activity. The objective of the present study was to extend the concept of capacity building to the assessment of training and development activity in an automobile component manufacturing organization, using a developed and…

The Influence of Corporate Leadership and Management Practices on a Public School District

ERIC Educational Resources Information Center

Napier, Randall Paul, Jr.

2012-01-01

The purpose of this case study is to understand how management and leadership ideas that were present in Toyota Motor Manufacturing Kentucky influenced management and leadership practices adopted by Scott County Public Schools during 2002-2011. Data for the study were collected during the summer of 2011, using individual and focus group interviews…

24 CFR 3280.702 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... a comfort cooling appliance where the condenser section is placed external to the manufactured home... a comfort cooling appliance where the condenser section is placed external to the manufactured home... case of a heat pump) heat air for use in comfort cooling (or heating) the living space. Air...

Outlet strut fracture of Björk-Shiley convexo-concave valves: can valve-manufacturing characteristics explain the risk?

PubMed

Omar, R Z; Morton, L S; Beirne, M; Blot, W J; Lawford, P V; Hose, R; Taylor, K M

2001-06-01

Björk-Shiley 60 degrees convexo-concave prosthetic heart valves (Shiley, Inc, Irvine, Calif, a subsidiary of Pfizer, Inc) continue to be a concern for approximately 35,000 nonexplanted patients worldwide, with approximately 600 events reported to the manufacturer to date. Fractures of the outlet struts of the valves began to appear in the early 1980s and have continued to the present, but their causes are only partially understood. A matched case-control study was conducted evaluating manufacturing records for 52 valves with outlet strut fractures and 248 control subjects matched for age at implantation, valve size, and valve position. In addition to the risk factors recognized as determinants of outlet strut fracture, the United Kingdom case-control study has observed 7- to 9-fold increased risk with performance of multiple hook deflection tests. This test was performed more than once, usually after rework on the valve. Six valves in this study underwent multiple hook deflection tests, of which 4 experienced an outlet strut fracture. Cracks and further rework were noted for these valves. Significant associations were also observed between outlet strut fracture and disc-to-strut gap measurements taken before the attachment of the sewing ring. It is our view that a combination of factors related to valve design, manufacturing process, and patient characteristics are responsible for outlet strut fractures of Björk-Shiley convexo-concave valves. Multiple hook deflection tests have emerged as a potential new risk factor for outlet strut fracture in both The Netherlands and the United Kingdom. This factor appears to be correlated with the presence of other abnormalities. A further study is needed to investigate the factors correlated with multiple hook deflection tests. On confirmation of risk, the presence of multiple hook deflection tests may be added to equations, quantifying the risk of outlet strut fracture for comparison against risk of mortality and serious morbidity from explant operations.

A manufacturing quality assessment model based-on two stages interval type-2 fuzzy logic

NASA Astrophysics Data System (ADS)

Purnomo, Muhammad Ridwan Andi; Helmi Shintya Dewi, Intan

2016-01-01

This paper presents the development of an assessment models for manufacturing quality using Interval Type-2 Fuzzy Logic (IT2-FL). The proposed model is developed based on one of building block in sustainable supply chain management (SSCM), which is benefit of SCM, and focuses more on quality. The proposed model can be used to predict the quality level of production chain in a company. The quality of production will affect to the quality of product. Practically, quality of production is unique for every type of production system. Hence, experts opinion will play major role in developing the assessment model. The model will become more complicated when the data contains ambiguity and uncertainty. In this study, IT2-FL is used to model the ambiguity and uncertainty. A case study taken from a company in Yogyakarta shows that the proposed manufacturing quality assessment model can work well in determining the quality level of production.

Characteristics and biodegradability of olive mill wastewaters.

PubMed

Karahan Özgün, Özlem; Pala Özkök, İlke; Kutay, Can; Orhon, Derin

2016-01-01

Olive mill wastewaters (OMWs) are mostly characterized by their high-organic content and complex organic compounds in addition to the phenolic compounds. European olive oil manufacturers have to cope up with the same wastewater treatment problem and the applied conventional treatment technologies for OMW were not proved to be very successful in each case. Olive mills are mostly small and medium-sized installations and OMW is generated during the three-four-month-long manufacturing season. The problem is not only the complex wastewater to be treated but also the scattered positioning of the olive mills, the seasonal wastewater generation and the size of the manufacturing facilities. The aim of the study is to identify the organic content of OMW and to assess the biological and chemical treatability of OMWs, in order to assist the development of integrated chemical-biological treatment schemes for best appropriate techniques implementation. The experimental studies show that separation of the particulate fraction improved the biodegradability or reduced the refractory and inhibitory effects of particulate organics.

Combining U.S.-based prioritization tools to improve screening level accountability for environmental impact: the case of the chemical manufacturing industry.

PubMed

Zhou, Xiaoying; Schoenung, Julie M

2009-12-15

There are two quantitative indicators that are most widely used to assess the extent of compliance of industrial facilities with environmental regulations: the quantity of hazardous waste generated and the amount of toxics released. These indicators, albeit useful in terms of some environmental monitoring, fail to account for direct or indirect effects on human and environmental health, especially when aggregating total quantity of releases for a facility or industry sector. Thus, there is a need for a more comprehensive approach that can prioritize a particular chemical (or industry sector) on the basis of its relevant environmental performance and impact on human health. Accordingly, the objective of the present study is to formulate an aggregation of tools that can simultaneously capture multiple effects and several environmental impact categories. This approach allows us to compare and combine results generated with the aid of select U.S.-based quantitative impact assessment tools, thereby supplementing compliance-based metrics such as data from the U.S. Toxic Release Inventory. A case study, which presents findings for the U.S. chemical manufacturing industry, is presented to illustrate the aggregation of these tools. Environmental impacts due to both upstream and manufacturing activities are also evaluated for each industry sector. The proposed combinatorial analysis allows for a more robust evaluation for rating and prioritizing the environmental impacts of industrial waste.

Multivariate statistical process control in product quality review assessment - A case study.

PubMed

Kharbach, M; Cherrah, Y; Vander Heyden, Y; Bouklouze, A

2017-11-01

According to the Food and Drug Administration and the European Good Manufacturing Practices (GMP) guidelines, Annual Product Review (APR) is a mandatory requirement in GMP. It consists of evaluating a large collection of qualitative or quantitative data in order to verify the consistency of an existing process. According to the Code of Federal Regulation Part 11 (21 CFR 211.180), all finished products should be reviewed annually for the quality standards to determine the need of any change in specification or manufacturing of drug products. Conventional Statistical Process Control (SPC) evaluates the pharmaceutical production process by examining only the effect of a single factor at the time using a Shewhart's chart. It neglects to take into account the interaction between the variables. In order to overcome this issue, Multivariate Statistical Process Control (MSPC) can be used. Our case study concerns an APR assessment, where 164 historical batches containing six active ingredients, manufactured in Morocco, were collected during one year. Each batch has been checked by assaying the six active ingredients by High Performance Liquid Chromatography according to European Pharmacopoeia monographs. The data matrix was evaluated both by SPC and MSPC. The SPC indicated that all batches are under control, while the MSPC, based on Principal Component Analysis (PCA), for the data being either autoscaled or robust scaled, showed four and seven batches, respectively, out of the Hotelling T 2 95% ellipse. Also, an improvement of the capability of the process is observed without the most extreme batches. The MSPC can be used for monitoring subtle changes in the manufacturing process during an APR assessment. Copyright © 2017 Académie Nationale de Pharmacie. Published by Elsevier Masson SAS. All rights reserved.

Data management in automated external defibrillators: a call for a standardised solution.

PubMed

Nielsen, A M; Rasmussen, L S

2011-07-01

The ECG data stored in automated external defibrillators (AEDs) may be valuable for establishing a final diagnosis and deciding further diagnostics and treatment. Different data management systems are used and this may create significant problems for data storage and access for physicians treating victims in whom an AED has been used. In this descriptive study, we collected information (number, manufacturer and model) on 17 December 2010 from a web page used for the voluntary registration of AEDs in Denmark. The manufacturers were contacted and asked to provide information about data downloading. There were 12 different manufactures and 20 different AED models. Five models were registered in a quantity <5. We report data from the remaining 15 models (3603 AEDs). Several models stored only one case or 15 min of ECG data. All models had a data transfer option, but most had outdated 'hardware': Seven had infrared transfer; one had a cable with a serial port. Four had a removable memory device, but only one was a USB. The software was available as freeware only in a few cases. Otherwise, a CD ROM was needed, some even with a licence. The software for the second most common AED could not be installed. The development of data management solutions is not a high priority. We encourage the manufacturers to collaborate with researchers to develop a simple data transfer solution in order to improve patient care and facilitate research. © 2011 The Authors. Acta Anaesthesiologica Scandinavica © 2011 The Acta Anaesthesiologica Scandinavica Foundation.

In vitro evaluation of microbial contamination of orthodontic brackets as received from the manufacturer using microbiological and molecular tests.

PubMed

Dos Santos Gerzson, Darlene R; Simon, Daniel; Dos Anjos, Aline Lima; Freitas, Maria Perpétua Mota

2015-11-01

To test the null hypothesis that orthodontic brackets as supplied by manufacturers do not have microbial contamination. The sample comprised 140 brackets of four different commercially available brands, used directly from the manufacturer's packaging, divided into 14 groups (n  =  10 brackets each). Of the 140 pieces, 60 were full cases and 80 were replacement brackets. Materials were tested to detect bacterial growth, analyze types of bacteria present (biochemical test), and identify bacteria (molecular test with polymerase chain reaction [PCR]). In two of 12 groups the brackets showed microbial contamination: group 1, Morelli full case brackets, and group 12, Abzil-3M Unitek replacement brackets. Staphylococcus aureus and Staphylococcus epidermidis were the bacteria identified in groups 1 and 12, respectively (suggested by the biochemical test and confirmed by PCR). Brackets of two brands (Morelli and Abzil-3M Unitek) were found to be contaminated by bacteria in the original packages supplied by the manufacturers, which suggests a risk for patient contamination. These data suggest that the manufacturers of these materials should improve the quality control of the packaging used, including sterilization, for the security of patient health.

Ethics in biomedical engineering.

PubMed

Morsy, Ahmed; Flexman, Jennifer

2008-01-01

This session focuses on a number of aspects of the subject of Ethics in Biomedical Engineering. The session starts by providing a case study of a company that manufactures artificial heart valves where the valves were failing at an unexpected rate. The case study focuses on Biomedical Engineers working at the company and how their education and training did not prepare them to deal properly with such situation. The second part of the session highlights the need to learn about various ethics rules and policies regulating research involving human or animal subjects.

Organizing the "Productive Transformation of Knowledge": Linking University and Industry in Traditional Manufacturing Areas

ERIC Educational Resources Information Center

Balduzzi, Giacomo; Rostan, Michele

2016-01-01

The article aims at underlining the role played by extra-academic and autonomous organizations strongly connected with university institutions and researchers in producing, acquiring, transferring and transforming knowledge. The study examines a particular Italian case, the "Politecnico Calzaturiero", a private institution providing…

Work Restructuring in Post-Apartheid South Africa.

ERIC Educational Resources Information Center

Webster, Edward; Omar, Rahmat

2003-01-01

Case studies of South African companies (mining, manufacturing, and telephone call centers) reveal a mix of management strategies that converge with and diverge from past practices. South Africa is attempting to balance the demands of efficiency, employee rights, and racial equity, a challenge that requires overcoming the legacy of the apartheid…

Managing Strategic Change through TQM: Learning from Failure.

ERIC Educational Resources Information Center

Redman, Tom; Grieves, Jim

1999-01-01

Case study of a manufacturing firm that implemented total quality management (TQM) found that the initiative may have failed because the company was undergoing rapid, radical structural change. Other problems included short-term focus, communication problems, and employee concerns about job security. TQM may be more compatible with continuous…

WASTE MINIMIZATION AUDIT REPORT: CASE STUDIES OF MINIMIZATION OF SOLVENT WASTE FROM PARTS CLEANING AND FROM ELECTRONIC CAPACITOR MANUFACTURING OPERATIONS

EPA Science Inventory

To promote waste minimization activities in accordance with the national policy objectives established under the 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and Recovery Act of 1976 (RCRA), the Hazardous Waste Engineering Research Laboratory (HWERL) of ...

Training of Existing Workers: Issues, Incentives and Models

ERIC Educational Resources Information Center

Mawer, Giselle; Jackson, Elaine

2005-01-01

This report presents issues associated with incentives for training existing workers in small to medium-sized firms, identified through a small sample of case studies from the retail, manufacturing, and building and construction industries. While the majority of employers recognise workforce skill levels are fundamental to the success of the…

Affordability and availability of off-patent drugs in the United States-the case for importing from abroad: observational study.

PubMed

Gupta, Ravi; Bollyky, Thomas J; Cohen, Matthew; Ross, Joseph S; Kesselheim, Aaron S

2018-03-19

To evaluate whether off-patent prescription drugs at risk of sudden price increases or shortages in the United States are available from independent manufacturers approved in other well regulated settings around the world. Observational study. Off-patent drugs in the USA and approved by the Food and Drug Administration, up to 10 April 2017. Novel tablet or capsule prescription drugs approved by the FDA since 1939 that were no longer protected by patents or other market exclusivity and had up to three generic versions. Number of additional manufacturers that had obtained approval from any of seven non-US regulators with similar standards (European Medicines Agency (European Union), HealthCanada (Canada), Therapeutic Goods Association (Australia), Medsafe (New Zealand), Swissmedic (Switzerland), Medicines Control Council (South Africa), and the Israel Health Ministry). Association with drug characteristics including US orphan drug designation for drugs treating rare diseases, World Health Organization essential medicine designation, treatment area, drug product complexity (that is, with attributes that could complicate establishing bioequivalence or manufacturing), and total Medicaid spending in 2015. Of 170 eligible study drugs, more than half (109, 64%) had at least one manufacturer approved by a non-US regulator and 32 (19%) had four or more. Among 44 (26%) drugs with no FDA approved generic versions, 21 (48%) were available from at least one manufacturer approved by one of the seven non-US regulators, and two (5%) by four or more manufacturers. Across all drugs and regulators (including the FDA), 66 (39%) drugs were available from four or more total manufacturers. Of 109 drugs with at least one non-US regulator approved manufacturer, 12 (11%) were approved for patients with rare diseases and 29 (27%) were WHO designated essential medicines; only 12 (11%) were complex products that might be more complicated to import. The highest numbers of drugs were indicated for treating cardiovascular diseases, diabetes, or hyperlipidemia (19, 17%); psychiatric disease (16, 15%); and infectious diseases (15, 14%). In 2015, Medicaid alone spent nearly US$700m (£508m; €570m) on generic drugs without adequate US competition that could have had a manufacturer approved by non-US peer regulatory agencies. In this study, more than half the off-patent drugs with no generic competition in the USA had at least one independent manufacturer approved by a non-US peer regulatory agency; slightly fewer than half had four or more total manufacturers. Facilitating US patient access to such manufacturers could help sustain affordable access to essential off-patent drugs. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Florida hospital saves 5.3 M dollars by adopting principles of lean manufacturing.

PubMed

2005-01-01

Florida hospital saves 5.3M dollars by adopting principles of lean manufacturing. Surgery cancellations have been slashed from 13% of cases to less than 3%, while emergency department admissions have increased by 20%. Those are just two of the results of a quality improvement project at Lee Memorial Health System in Fort Myers, FL, that focused on using the principles of lean manufacturing to improve patient flow in the five-hospital system

Application of Twin Screw Extrusion in the Manufacture of Cocrystals, Part I: Four Case Studies

PubMed Central

Daurio, Dominick; Medina, Cesar; Saw, Robert; Nagapudi, Karthik; Alvarez-Núñez, Fernando

2011-01-01

The application of twin screw extrusion (TSE) as a scalable and green process for the manufacture of cocrystals was investigated. Four model cocrystal forming systems, Caffeine-Oxalic acid, Nicotinamide-trans cinnamic acid, Carbamazepine-Saccharin, and Theophylline-Citric acid, were selected for the study. The parameters of the extrusion process that influenced cocrystal formation were examined. TSE was found to be an effective method to make cocrystals for all four systems studied. It was demonstrated that temperature and extent of mixing in the extruder were the primary process parameters that influenced extent of conversion to the cocrystal in neat TSE experiments. In addition to neat extrusion, liquid-assisted TSE was also demonstrated for the first time as a viable process for making cocrystals. Notably, the use of catalytic amount of benign solvents led to a lowering of processing temperatures required to form the cocrystal in the extruder. TSE should be considered as an efficient, scalable, and environmentally friendly process for the manufacture of cocrystals with little to no solvent requirements. PMID:24310598

Study of a dry room in a battery manufacturing plant using a process model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahmed, Shabbir; Nelson, Paul A.; Dees, Dennis W.

The manufacture of lithium ion batteries requires some processing steps to be carried out in a dry room, where the moisture content should remain below 100 parts per million. The design and operation of such a dry room adds to the cost of the battery. This paper studies the humidity management of the air to and from the dry room to understand the impact of design and operating parameters on the energy demand and the cost contribution towards the battery manufacturing cost. The study is conducted with the help of a process model for a dry room with a volumemore » of 16000 cubic meters. For a defined base case scenario it is found that the dry room operation has an energy demand of approximately 400 kW. The paper explores some tradeoffs in design and operating parameters by looking at the humidity reduction by quenching the make-up air vs. at the desiccant wheel, and the impact of the heat recovery from the desiccant regeneration cycle.« less

Freon injection injury to the hand. A report of four cases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goetting, A.T.; Carson, J.; Burton, B.T.

1992-08-01

During a 6-month period, the poison center was consulted on three occasions for advice regarding accidental injection of hexafluorethane (Freon) used in the manufacturing process of athletic shoes. A fourth case was later identified after consulting physicians near the manufacturing facility. Little information exists in the medical literature concerning injection of freon or other volatile substances. In each of these cases, workers inadvertently injected concentrated hexafluorethane into a finger while holding the shoe component and attempting to inject hexafluorethane. Each case presented with edema, limitation of motion, and crepitation. Hand roentgenogram revealed subcutaneous gas. Treatment was nonsurgical, consisting of splinting,more » tetanus immunization, and antibiotics. Rapid resolution of symptoms occurred in all four cases. Hexafluorethane is relatively inert when injected and has low toxicity. However, potential rapid expansion warrants observation for pressure injury.« less

Completeness of serious adverse drug event reports received by the US Food and Drug Administration in 2014.

PubMed

Moore, Thomas J; Furberg, Curt D; Mattison, Donald R; Cohen, Michael R

2016-06-01

Adverse drug event reports to the US Food and Drug Administration (FDA) remain the primary tool for identifying serious drug adverse effects without adequate existing warnings. We assessed the completeness of reports the FDA received in 2014. Serious adverse drug event reports were evaluated for whether they included age, gender, event date, and at least one medical term describing the event in computer excerpts. Report sources were direct reports to the FDA, manufacturer expedited reports about events without adequate warnings, and manufacturer periodic reports about events with existing warnings. In 2014, the FDA received 528,192 new case reports indicating a serious or fatal outcome, 25,038 (4.7%) directly from health professionals and consumers, and 503,154 (95.3%) from drug manufacturers. Overall, 21,595 (86.2%) of serious reports submitted directly to the FDA provided data for all four completeness variables, compared with 271,022 (40.4%) of manufacturer expedited reports and 24,988 (51.3%) of periodic reports. Among manufacturer serious reports, 37.9% lacked age and 46.9% had no event date. Performance by 25 manufacturers submitting 5000 or more reports varied from 24.4% complete on all variables to 67% complete. Patient death cases had the lowest completeness scores in all categories. By these measures, report completeness from drug manufacturers was poor compared with direct submissions to the agency. The FDA needs to update reporting requirements and compliance policies to help industry capture better adverse event information from new forms of manufacturer interactions with health professionals and consumers. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Pharmaceutical companies' role in state vaccination policymaking: the case of human papillomavirus vaccination.

PubMed

Mello, Michelle M; Abiola, Sara; Colgrove, James

2012-05-01

We sought to investigate roles that Merck & Co Inc played in state human papillomavirus (HPV) immunization policymaking, to elicit key stakeholders' perceptions of the appropriateness of these activities, and to explore implications for relationships between health policymakers and industry. We used a series of state case studies combining data from key informant interviews with analysis of media reports and archival materials. We interviewed 73 key informants in 6 states that were actively engaged in HPV vaccine policy deliberations. Merck promoted school-entry mandate legislation by serving as an information resource, lobbying legislators, drafting legislation, mobilizing female legislators and physician organizations, conducting consumer marketing campaigns, and filling gaps in access to the vaccine. Legislators relied heavily on Merck for scientific information. Most stakeholders found lobbying by vaccine manufacturers acceptable in principle, but perceived that Merck had acted too aggressively and nontransparently in this case. Although policymakers acknowledge the utility of manufacturers' involvement in vaccination policymaking, industry lobbying that is overly aggressive, not fully transparent, or not divorced from financial contributions to lawmakers risks undermining the prospects for legislation to foster uptake of new vaccines.

Occupational risk and the development of premalignant skin lesions among paraquat manufacturers.

PubMed

Wang, J D; Li, W E; Hu, F C; Hu, K H

1987-03-01

The objective of this study was to determine the prevalence rate and possible aetiological factors of premalignant skin lesions observed among paraquat manufacturers. A total of 228 workers in 28 factories were interviewed and independently examined by a dermatologist during site inspection in 1985. Information concerning past working experience, current toxic exposures, other risk factors of hyperpigmented macules and keratosis, and the past and present manufacturing processes of each factory was collected. Sixty nine cases of hyperpigmented macules and 17 of hyperkeratosis were found. Typical macules were irregular in shape, pin head size, hyperpigmented, with or without hyperkeratosis, and usually distributed symmetrically over the forearms, hands, neck, and upper chest, where exposure to sunlight was maximal. Six patients with hyperkeratotic lesions subsequently had biopsies performed and two showed Bowenoid changes. Eighty per cent (28 cases) and 67% (38 cases) of workers developed hyperpigmented macules if they had ever been engaged in bipyridine centrifugation and crystallisation, respectively; there were three workers 3% with such lesions among those who performed packaging or administrative jobs, or both. There was a significant trend (p less than 0.0001) for workers to develop hyperpigmented macules and hyperkeratosis the longer they had been exposed to centrifugation or crystallisation, or both, independent of age and the duration of exposure to sunlight. Evidence is presented to suggest that sunlight is a necessary cofactor and that the aetiological agent was produced during high temperature sodium process of bipyridine synthesis, and possibly bipyridine isomer(s).

Stamping of Thin-Walled Structural Components with Magnesium Alloy AZ31 Sheets

NASA Astrophysics Data System (ADS)

Chen, Fuh-Kuo; Chang, Chih-Kun

2005-08-01

In the present study, the stamping process for manufacturing cell phone cases with magnesium alloy AZ31 sheets was studied using both the experimental approach and the finite element analysis. In order to determine the proper forming temperature and set up a fracture criterion, tensile tests and forming limit tests were first conducted to obtain the mechanical behaviors of AZ31 sheets at various elevated temperatures. The mechanical properties of Z31 sheets obtained from the experiments were then adopted in the finite element analysis to investigate the effects of the process parameters on the formability of the stamping process of cell phone cases. The finite element simulation results revealed that both the fracture and wrinkle defects could not be eliminated at the same time by adjusting blank-holder force or blank size. A drawbead design was then performed using the finite element simulations to determine the size and the location of drawbead required to suppress the wrinkle defect. An optimum stamping process, including die geometry, forming temperature, and blank dimension, was then determined for manufacturing the cell phone cases. The finite element analysis was validated by the good agreement between the simulation results and the experimental data. It confirms that the cell phone cases can be produced with magnesium alloy AZ31 sheet by the stamping process at elevated temperatures.

The Effects of Partnership Management on Supply Chain Cooperative Performance: A Case Study of High-Tech Industry

NASA Astrophysics Data System (ADS)

Wu, Mei-Ying; Chang, Yun-Ju; Weng, Yung-Chien

2009-08-01

With the structural change of global supply chains, the relationship between manufacturers and suppliers has transformed into a long-term partnership. Thus, this study aims to explore the partnership between manufacturers and suppliers in Taiwan's high-tech industry. Four constructs, including partner characteristic, partnership quality, partnership closeness, and cooperative performance, induced from previous literatures are used to construct the research framework and hypotheses. A questionnaire survey is then performed on executives and staffs involved in the high-tech industry. The proposed framework and hypotheses are empirically validated through confirmatory factory analysis and structural equation modeling. It is expected that the research findings can serve as a reference for Taiwan's high-tech industry on building partnerships.

Searching for unpublished data for Cochrane reviews: cross sectional study

PubMed Central

Bero, Lisa; Gøtzsche, Peter C

2013-01-01

Objective To describe the experiences of authors of Cochrane reviews in searching for, getting access to, and using unpublished data. Design Cross sectional study. Setting Cochrane reviews. Participants 2184 corresponding authors of Cochrane reviews as of May 2012. Main outcome measure Frequencies of responses to open ended and closed questions in an online survey. Results Of 5915 authors contacted by email, 2184 replied (36.9% response rate). Of those, 1656 (75.8%) had searched for unpublished data. In 913 cases (55.1% of 1656), new data were obtained and we received details about these data for 794 data sources. The most common data source was “trialists/investigators,” accounting for 73.9% (n=587) of the 794 data sources. Most of the data were used in the review (82.0%, 651/794) and in 53.4% (424/794) of cases data were provided in less than a month. Summary data were most common, provided by 50.8% (403/794) of the data sources, whereas 20.5% (163/794) provided individual patient data. In only 6.3% (50/794) of cases were data reported to have been obtained from the manufacturers, and this group waited longer and had to make more contacts to get the data. The data from manufacturers were less likely to be for individual patients and less likely to be used in the review. Data from regulatory agencies accounted for 3.0% (24/794) of the obtained data. Conclusions Most authors of Cochrane reviews who searched for unpublished data received useful information, primarily from trialists. Our response rate was low and the authors who did not respond were probably less likely to have searched for unpublished data. Manufacturers and regulatory agencies were uncommon sources of unpublished data. PMID:23613540

Searching for unpublished data for Cochrane reviews: cross sectional study.

PubMed

Schroll, Jeppe Bennekou; Bero, Lisa; Gøtzsche, Peter C

2013-04-23

To describe the experiences of authors of Cochrane reviews in searching for, getting access to, and using unpublished data. Cross sectional study. Cochrane reviews. 2184 corresponding authors of Cochrane reviews as of May 2012. Frequencies of responses to open ended and closed questions in an online survey. Of 5915 authors contacted by email, 2184 replied (36.9% response rate). Of those, 1656 (75.8%) had searched for unpublished data. In 913 cases (55.1% of 1656), new data were obtained and we received details about these data for 794 data sources. The most common data source was "trialists/investigators," accounting for 73.9% (n=587) of the 794 data sources. Most of the data were used in the review (82.0%, 651/794) and in 53.4% (424/794) of cases data were provided in less than a month. Summary data were most common, provided by 50.8% (403/794) of the data sources, whereas 20.5% (163/794) provided individual patient data. In only 6.3% (50/794) of cases were data reported to have been obtained from the manufacturers, and this group waited longer and had to make more contacts to get the data. The data from manufacturers were less likely to be for individual patients and less likely to be used in the review. Data from regulatory agencies accounted for 3.0% (24/794) of the obtained data. Most authors of Cochrane reviews who searched for unpublished data received useful information, primarily from trialists. Our response rate was low and the authors who did not respond were probably less likely to have searched for unpublished data. Manufacturers and regulatory agencies were uncommon sources of unpublished data.

Mortality and cancer incidence among alachlor manufacturing workers 1968-99.

PubMed

Acquavella, J F; Delzell, E; Cheng, H; Lynch, C F; Johnson, G

2004-08-01

Alachlor is the active ingredient in pre-emergent herbicide formulations that have been used widely on corn, soybeans, and other crops. It has been found to cause nasal, stomach, and thyroid tumours in rodent feeding studies at levels that are much higher than likely human exposures. To evaluate mortality rates from 1968 to 1999 and cancer incidence rates from 1969 to 1999 for alachlor manufacturing workers at a plant in Muscatine, Iowa. Worker mortality and cancer incidence rates were compared to corresponding rates for the Iowa state general population. Analyses addressed potential intensity and duration of exposure. For workers with any period of high alachlor exposure, mortality from all causes combined was lower than expected (42 observed deaths, SMR 64, 95% CI 46 to 86) and cancer mortality was slightly lower than expected (13 observed deaths, SMR 79, 95% CI 42 to 136). Cancer incidence for workers with potential high exposure was similar to that for Iowa residents, both overall (29 observed cases, SIR 123, 95% CI 82 to 177) and for workers exposed for five or more years and with at least 15 years since first exposure (eight observed cases, SIR 113, 95% CI 49 to 224). There were no cases of nasal, stomach, or thyroid cancer. There were no cancers of the types found in toxicology studies and no discernible relation between cancer incidence for any site and years of alachlor exposure or time since first exposure. Despite the small size of this population, the findings are important because these workers had chronic exposure potential during extended manufacturing campaigns, while use in agriculture is typically limited to a few days or weeks each year.

Application of FUN3D and CFL3D to the Third Workshop on CFD Uncertainty Analysis

NASA Technical Reports Server (NTRS)

Rumsey, C. L.; Thomas, J. L.

2008-01-01

Two Reynolds-averaged Navier-Stokes computer codes - one unstructured and one structured - are applied to two workshop cases (for the 3rd Workshop on CFD Uncertainty Analysis, held at Instituto Superior Tecnico, Lisbon, in October 2008) for the purpose of uncertainty analysis. The Spalart-Allmaras turbulence model is employed. The first case uses the method of manufactured solution and is intended as a verification case. In other words, the CFD solution is expected to approach the exact solution as the grid is refined. The second case is a validation case (comparison against experiment), for which modeling errors inherent in the turbulence model and errors/uncertainty in the experiment may prevent close agreement. The results from the two computer codes are also compared. This exercise verifies that the codes are consistent both with the exact manufactured solution and with each other. In terms of order property, both codes behave as expected for the manufactured solution. For the backward facing step, CFD uncertainty on the finest grid is computed and is generally very low for both codes (whose results are nearly identical). Agreement with experiment is good at some locations for particular variables, but there are also many areas where the CFD and experimental uncertainties do not overlap.

The effects of gray scale image processing on digital mammography interpretation performance.

PubMed

Cole, Elodia B; Pisano, Etta D; Zeng, Donglin; Muller, Keith; Aylward, Stephen R; Park, Sungwook; Kuzmiak, Cherie; Koomen, Marcia; Pavic, Dag; Walsh, Ruth; Baker, Jay; Gimenez, Edgardo I; Freimanis, Rita

2005-05-01

To determine the effects of three image-processing algorithms on diagnostic accuracy of digital mammography in comparison with conventional screen-film mammography. A total of 201 cases consisting of nonprocessed soft copy versions of the digital mammograms acquired from GE, Fischer, and Trex digital mammography systems (1997-1999) and conventional screen-film mammograms of the same patients were interpreted by nine radiologists. The raw digital data were processed with each of three different image-processing algorithms creating three presentations-manufacturer's default (applied and laser printed to film by each of the manufacturers), MUSICA, and PLAHE-were presented in soft copy display. There were three radiologists per presentation. Area under the receiver operating characteristic curve for GE digital mass cases was worse than screen-film for all digital presentations. The area under the receiver operating characteristic for Trex digital mass cases was better, but only with images processed with the manufacturer's default algorithm. Sensitivity for GE digital mass cases was worse than screen film for all digital presentations. Specificity for Fischer digital calcifications cases was worse than screen film for images processed in default and PLAHE algorithms. Specificity for Trex digital calcifications cases was worse than screen film for images processed with MUSICA. Specific image-processing algorithms may be necessary for optimal presentation for interpretation based on machine and lesion type.

40 CFR 89.118 - Deterioration factors and service accumulation.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., subsystems, or components selected by the manufacturer under § 89.117(d). The manufacturer shall describe the... must be based on good engineering judgment. (iii) Engineering analysis for established technologies. (A) In the case where an engine family uses established technology, an analysis based on good engineering...

40 CFR 89.118 - Deterioration factors and service accumulation.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., subsystems, or components selected by the manufacturer under § 89.117(d). The manufacturer shall describe the... must be based on good engineering judgment. (iii) Engineering analysis for established technologies. (A) In the case where an engine family uses established technology, an analysis based on good engineering...

40 CFR 89.118 - Deterioration factors and service accumulation.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., subsystems, or components selected by the manufacturer under § 89.117(d). The manufacturer shall describe the... must be based on good engineering judgment. (iii) Engineering analysis for established technologies. (A) In the case where an engine family uses established technology, an analysis based on good engineering...

40 CFR 89.118 - Deterioration factors and service accumulation.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., subsystems, or components selected by the manufacturer under § 89.117(d). The manufacturer shall describe the... must be based on good engineering judgment. (iii) Engineering analysis for established technologies. (A) In the case where an engine family uses established technology, an analysis based on good engineering...

40 CFR 89.118 - Deterioration factors and service accumulation.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., subsystems, or components selected by the manufacturer under § 89.117(d). The manufacturer shall describe the... must be based on good engineering judgment. (iii) Engineering analysis for established technologies. (A) In the case where an engine family uses established technology, an analysis based on good engineering...

40 CFR 86.007-30 - Certification.

Code of Federal Regulations, 2014 CFR

2014-07-01

... certificate may be deemed void ab initio. (C) The manufacturer shall bear the burden of establishing to the... be deemed void ab initio. (C) The manufacturer shall bear the burden of establishing to the... of conformity, the Administrator may deem such certificate void ab initio. (4) In any case in which...

40 CFR 91.1103 - Prohibited acts.

Code of Federal Regulations, 2010 CFR

2010-07-01

... case of a manufacturer of new marine SI engines or vessels for distribution in commerce, the sale, the offering for sale, or the introduction, or delivery for introduction, into commerce, of any new marine SI... deliver into commerce, a marine SI engine unless the manufacturer has complied with the requirements of...

49 CFR 577.5 - Notification pursuant to a manufacturer's decision.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., the difference between the performance of the noncomplying vehicle or item of replacement equipment and the performance specified by the standard; (3) A statement of any operating or other conditions... remedy tires without charge. (iii) In the case of remedy by repair through the manufacturer's dealers or...

77 FR 57191 - Proposed Collection; Comment Request for Notice 2006-54

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-17

... Notice 2006-54, Alternative Fuel Motor Vehicle Credit. DATES: Written comments should be received on or... INFORMATION: Title: Alternative Fuel Motor Vehicle Credit. OMB Number: 1545-1993. Notice Number: Notice 2006... motor vehicles to rely on the domestic manufacturer's (or, in the case of a foreign manufacturer, its...

49 CFR 579.3 - Application.

Code of Federal Regulations, 2010 CFR

2010-10-01

... for sale, sold, or leased in the United States by the manufacturer, including any parent corporation... sale, sold, or leased in a foreign country by the manufacturer, including any parent corporation, any... offered for sale, sold, or leased in the United States. (b) In the case of any report required under...

Job rotation designed to prevent musculoskeletal disorders and control risk in manufacturing industries: A systematic review.

PubMed

Padula, Rosimeire Simprini; Comper, Maria Luiza Caires; Sparer, Emily H; Dennerlein, Jack T

2017-01-01

To better understand job rotation in the manufacturing industry, we completed a systematic review asking the following questions: 1) How do job-rotation programs impact work-related musculoskeletal disorders (MSDs) and related risk control for these MSDs, as well as psychosocial factors? and 2) How best should the job rotation programs be designed? We searched MEDLINE, EMBASE, Business Source Premier, ISI Web of Knowledge, CINAHL, PsyINFO, Scopus, and SciELO databases for articles published in peer-reviewed journals. Eligible studies were examined by two independent reviewers for relevance (population of manufacturing workers, outcomes of musculoskeletal disorders, physical factors, psychosocial factors, and strategies used in job-rotation implantation) and methodological quality rating. From 10,809 potential articles, 71 were read for full text analysis. Of the 14 studies included for data extraction, two were non-randomized control trial studies, one was a case-control study, and 11 were cross-sectional comparisons. Only one, with a case-control design, was scored with good methodological quality. Currently, weak evidence exists supporting job rotation as a strategy for the prevention and control of musculoskeletal disorders. Job rotation did not appear to reduce the exposure of physical risk factors; yet, there are positive correlations between job rotation and higher job satisfaction. Worker training has been described as a crucial component of a successful job-rotation program. The studies reported a range of parameters used to implement and measure job-rotation programs. More rigorous studies are needed to better understand the full impact of job rotation on production and health. CRD42014013319. Copyright © 2016 Elsevier Ltd. All rights reserved.

Green perspective in food industry production line design: A review

NASA Astrophysics Data System (ADS)

Xian, C. Y.; Sin, T. C.; Liyana, M. R. N.; Awang, A.; Fathullah, M.

2017-09-01

The design of green manufacturing process in food industries is currently a hot research topic in the multidisciplinary area of applied chemistry, biology and technology. Several process such as freezing, cutting, drying, tempering, bleaching, sterilization, extraction and filtering have been applied efficiency in the food industry. Due to the rapid development of food and peripheral technology, the use of new physical processing or auxiliary processing methods can maintain food inherent nutrients, texture, color, and freshness and also reduce environmental pollution and energy consumption in food processing. Hence, this review paper will study and summarize the effects of green manufacturing process in food industries in term of waste reduction, materials and sustainability manufacturing. In any case, All the food processing equipment must comply with strict standards and regulation, this action will ensure the securing the food quality and safety of food products to consumers.

MRP (materiel requirements planning) II implementation: a case study.

PubMed

Sheldon, D

1994-05-01

Manufacturing resource planning (MRP II) is a powerful and effective business planning template on which to build a continuous improvement culture. MRP II, when successfully implemented, encourages a disciplined yet nonthreatening environment centered on measurement and accountability. From the education that accompanies an MRP II implementation, the employees can better understand the vision and mission of the organization. This common goal keeps everyone's energy directed toward the same final objective. The Raymond Corporation is a major materiels handling equipment manufacturer headquartered in Greene, New York, with class "A" MRP II manufacturing facilities in Greene and Brantford, Ontario and an aftermark distribution facility in East Syracuse, New York. Prior to the implementation of MRP II in its Greene plant (from 1988 through 1990) good intentions and hard work were proving to be less than necessary to compete in the global market. Certified class "A" in February 1990. The Raymond Corporation has built a world-class organization from these foundations.

Continuous powder feeding for pharmaceutical solid dosage form manufacture: a short review.

PubMed

Blackshields, Caroline A; Crean, Abina M

2018-07-01

There has been a noticeable shift from pharmaceutical batch processing towards a more continuous mode of manufacture for solid oral dosage forms. Continuous solid oral dose processes would not be possible in the absence of a highly accurate feeding system. The performance of feeders defines the content of formulations and is therefore a critical operation in continuous manufacturing of solid dosage forms. It was the purpose of this review to review the role of the initial powder feeding step in a continuous manufacturing process. Different feeding mechanisms are discussed with a particular emphasis on screw controlled loss in weight (LIW) feeding. The importance of understanding the physical properties of the raw materials and its impact on the feeding process is reviewed. Prior knowledge of materials provides an initial indication of how the powders will behave through processing and facilitates in the selection of the most suitable (i) feeder (capacity), (ii) feeding mechanism, and (iii) in the case of screw feeder - screw type. The studies identified in this review focus on the impact of material on powder feeding performance.

Hierarchical modeling of professional skills in the field of castings manufacture engineering

NASA Astrophysics Data System (ADS)

Samuilă, V.; Soporan, V. F.; Conțiu, G.; Pădurețu, S.; Lehene, T. R.; Vescan, M. M.

2017-06-01

The paper presents a method of hierarchizing professional skills in the manufacturing of molded parts (castings) by using and adapting the FAHP algorithm (Fuzzy Analitical Hierarchy Process). Assessments are made regarding the peculiarities of the professional training process, specifying the activities to be carried out and the competences necessary for their development. The contribution of the design of the method extends to the design of the hierarchy system architecture, the linguistic determination of the importance of each characteristic, the construction of the fuzzy ordering matrices for each stage of the process, the determination of the share of the characteristics for each hierarchy step and establishing the hierarchy of the characteristics taking into account the influences of the others, grouped at the level of the steps and within the global matrix. The research carried out represents the support for generating an instrument of hierarchy of professional competencies that can be used in various professional and institutional contexts. Case study on the hierarchy of professional skills in the manufacturing of molded parts engineering. Keywords: Materials engineering, castings manufacture professional skills, hierarchy, AHP method, standard occupational curriculum.

Understanding and modeling the economics of ECM

NASA Astrophysics Data System (ADS)

Wells, Wayne E.; Edinbarough, Immanuel A.

2004-12-01

Traditional economic analysis methods for manufacturing decisions include only the clearly identified immediate cost and revenue streams. Environmental issues have generally been seen as costs, in the form of waste material losses, conformance tests and pre-discharge treatments. The components of the waste stream often purchased as raw materials, become liabilities at the "end of the pipe" and their intrinsic material value is seldom recognized. A new mathematical treatment of manufacturing economics is proposed in which the costs of separation are compared with the intrinsic value of the waste materials to show how their recovery can provide an economic advantage to the manufacturer. The model is based on a unique combination of thermodynamic analysis, economic modeling and linear optimization. This paper describes the proposed model, and examines case studies in which the changed decision rules have yielded significant savings while protecting the environment. The premise proposed is that by including the value of the waste materials in the profit objective of the firm and applying the appropriate technological solution, manufacturing processes can become closed systems in which losses approach zero and environmental problems are converted into economic savings.

Drivers and barriers to e-invoicing adoption in Greek large scale manufacturing industries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marinagi, Catherine, E-mail: marinagi@teihal.gr, E-mail: ptrivel@yahoo.com, E-mail: preklitis@yahoo.com; Trivellas, Panagiotis, E-mail: marinagi@teihal.gr, E-mail: ptrivel@yahoo.com, E-mail: preklitis@yahoo.com; Reklitis, Panagiotis, E-mail: marinagi@teihal.gr, E-mail: ptrivel@yahoo.com, E-mail: preklitis@yahoo.com

2015-02-09

This paper attempts to investigate the drivers and barriers that large-scale Greek manufacturing industries experience in adopting electronic invoices (e-invoices), based on three case studies with organizations having international presence in many countries. The study focuses on the drivers that may affect the increase of the adoption and use of e-invoicing, including the customers demand for e-invoices, and sufficient know-how and adoption of e-invoicing in organizations. In addition, the study reveals important barriers that prevent the expansion of e-invoicing, such as suppliers’ reluctance to implement e-invoicing, and IT infrastructures incompatibilities. Other issues examined by this study include the observed benefitsmore » from e-invoicing implementation, and the financial priorities of the organizations assumed to be supported by e-invoicing.« less

The Ford Partnership for Advanced Studies: A New Case for Curriculum Integration in Technology Education

ERIC Educational Resources Information Center

Zinser, Richard; Poledink, Paul

2005-01-01

The Ford Motor Company launched a new pre-engineering curriculum for high schools in the Fall of 2004. Building on an earlier manufacturing program, the development process for the Ford Partnership for Advanced Studies took approximately three years. Ford and the course designers wanted the new program to incorporate the best principles and…

CAD/CAM at a Distance: Assessing the Effectiveness of Web-Based Instruction To Meet Workforce Development Needs. AIR 2000 Annual Forum Paper.

ERIC Educational Resources Information Center

Wilkerson, Joyce A.; Elkins, Susan A.

This qualitative case study assessed web-based instruction in a computer-aided design/computer-assisted manufacturing (CAD/CAM) course designed for workforce development. The study examined students' and instructors' experience in a CAD/CAM course delivered exclusively on the Internet, evaluating course content and delivery, clarity of…

How Newcomers Learn the Social Norms of an Organization: A Case Study of the Socialization of Newly Hired Engineers. Research Brief

ERIC Educational Resources Information Center

Korte, Russel

2009-01-01

Current scholarship views organizational socialization as a learning process that is primarily the responsibility of the newcomer. Yet recent learning research recognizes the importance of the social interactions in the learning process. This study investigated how newly hired engineers at a large manufacturing company learned job-related tasks…

The Effects of Temporary Services and Contracting Out on Low-Skilled Workers: Evidence from Auto Suppliers, Hospitals, and Public Schools. Staff Working Paper.

ERIC Educational Resources Information Center

Erickcek, George; Houseman, Susan; Kalleberg, Arne

A study examined why employers use temporary agency and contract company workers and implications of these practices for wages, benefits, and working conditions of workers in low-skilled labor markets. Case studies in manufacturing (automotive supply), services (hospitals), and public sector (primary and secondary schools) industries defined the…

Using RFID Tagging in a Mining Industry Maintenance, Repair, and Operating (MRO) Supply Warehouse: A Case Study

ERIC Educational Resources Information Center

Smith, George D.

2008-01-01

The use of Radio Frequency Identification (RFID) technology has been shown to be successful by reducing operating costs in the retail and manufacturing industries, but has never been considered in the literature for a mining industry maintenance, repair, and operating (MRO) supply chain. This field study was conducted to determine whether or not…

Costs incurred by applying computer-aided design/computer-aided manufacturing techniques for the reconstruction of maxillofacial defects.

PubMed

Rustemeyer, Jan; Melenberg, Alex; Sari-Rieger, Aynur

2014-12-01

This study aims to evaluate the additional costs incurred by using a computer-aided design/computer-aided manufacturing (CAD/CAM) technique for reconstructing maxillofacial defects by analyzing typical cases. The medical charts of 11 consecutive patients who were subjected to the CAD/CAM technique were considered, and invoices from the companies providing the CAD/CAM devices were reviewed for every case. The number of devices used was significantly correlated with cost (r = 0.880; p < 0.001). Significant differences in mean costs were found between cases in which prebent reconstruction plates were used (€3346.00 ± €29.00) and cases in which they were not (€2534.22 ± €264.48; p < 0.001). Significant differences were also obtained between the costs of two, three and four devices, even when ignoring the cost of reconstruction plates. Additional fees provided by statutory health insurance covered a mean of 171.5% ± 25.6% of the cost of the CAD/CAM devices. Since the additional fees provide financial compensation, we believe that the CAD/CAM technique is suited for wide application and not restricted to complex cases. Where additional fees/funds are not available, the CAD/CAM technique might be unprofitable, so the decision whether or not to use it remains a case-to-case decision with respect to cost versus benefit. Copyright © 2014 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Effect of Manufacturing Procedures on Human Islet Isolation from Donor Pancreata Standardized by the North American Islet Donor Score

PubMed Central

Yeh, Chun-Chieh; Wang, Ling-Jia; Mcgarrigle, James J.; Wang, Yong; Liao, Chien-Chang; Omami, Mustafa; Khan, Arshad; Nourmohammadzadeh, Mohammad; Mendoza-Elias, Joshua; Mccracken, Benjamin; Marchese, Enza; Barbaro, Barbara; Oberholzer, Jose

2017-01-01

This study investigates manufacturing procedures that affect islet isolation outcomes from donor pancreata standardized by the North American Islet Donor Score (NAIDS). Islet isolations performed at the University of Illinois, Chicago, from pancreata with NAIDS ≥65 were investigated. The research cohort was categorized into two groups based on a postpurification yield either greater than (group A) or less than (group B) 400,000 IEQ. Associations between manufacturing procedures and islet isolation outcomes were analyzed using multivariate logistic or linear regressions. A total of 119 cases were retrieved from 630 islet isolations performed since 2003. Group A is composed of 40 cases with an average postpurified yield of 570,098 IEQ, whereas group B comprised 79 cases with an average yield of 235,987 IEQ. One third of 119 cases were considered successful islet isolations that yielded >400,000 IEQ. The prepurified and postpurified islet product outcome parameters were detailed for future reference. The NAIDS (>80 vs. 65–80) [odds ratio (OR): 2.91, 95% confidence interval (CI): 1.27–6.70], cold ischemic time (≤10 vs. >10 h) (OR: 3.68, 95% CI: 1.61–8.39), and enzyme perfusion method (mechanical vs. manual) (OR: 2.38, 95% CI: 1.01–5.56) were independent determinants for postpurified islet yield ≥400,000 IEQ. The NAIDS (>80, p < 0.001), cold ischemic time (≤10 h, p < 0.05), increased unit of collagenase (p < 0.01), and pancreatic duct cannulation time (<30 min, p < 0.01) all independently correlated with better islet quantity parameters. Furthermore, cold ischemic time (≤10 h, p < 0.05), liberase MTF (p < 0.001), increased unit of collagenase (p < 0.05), duct cannulation time (<30 min, p < 0.05), and mechanical enzyme perfusion (p < 0.05) were independently associated with better islet morphology score. Analysis of islet manufacturing procedures from the pancreata with standardized quality is essential in identifying technical issues within islet isolation. Adequate processing duration in each step of islet isolation, using liberase MTF, and mechanical enzyme perfusion all affect isolation outcomes. PMID:27524672

Cost benefit of investment on quality in pharmaceutical manufacturing: WHO GMP pre- and post-certification of a Nigerian pharmaceutical manufacturer.

PubMed

Anyakora, Chimezie; Ekwunife, Obinna; Alozie, Faith; Esuga, Mopa; Ukwuru, Jonathan; Onya, Steve; Nwokike, Jude

2017-09-18

Pharmaceutical companies in Africa need to invest in both facilities and quality management systems to achieve good manufacturing practice (GMP) compliance. Compliance to international GMP standards is important to the attainment of World Health Organization (WHO) prequalification. However, most of the local pharmaceutical manufacturing companies may be deterred from investing in quality because of many reasons, ranging from financial constraints to technical capacity. This paper primarily evaluates benefits against the cost of investing in GMP, using a Nigerian pharmaceutical company, Chi Pharmaceuticals Limited, as a case study. This paper also discusses how to drive more local manufacturers to invest in quality to attain GMP compliance; and proffers practical recommendations for local manufacturers who would want to invest in quality to meet ethical and regulatory obligations. The cost benefit of improving the quality of Chi Pharmaceuticals Limited's facilities and system to attain WHO GMP certification for the production of zinc sulfate 20-mg dispersible tablets was calculated by dividing the annual benefits derived from quality improvement interventions by the annual costs of implementing quality improvement interventions, referred to as a benefit-cost ratio (BCR). Cost benefit of obtaining WHO GMP certification for the production of zinc sulfate 20-mg dispersible tablets was 5.3 (95% confidence interval of 5.0-5.5). Investment in quality improvement intervention is cost-beneficial for local manufacturing companies. Governments and regulators in African countries should support pharmaceutical companies striving to invest in quality. Collaboration of local manufacturing companies with global companies will further improve quality. Local pharmaceutical companies should be encouraged to key into development opportunities available for pharmaceutical companies in Africa.

Work-related olfactory disorder: a case series and review.

PubMed

Park, Soon Woo; Kang, Young Joong; Eom, Huisu; Cho, Hyun-Jin; Ahn, Jungho; Lee, Sang-Gil

2018-01-01

The olfactory bulb is anatomically exposed and thus can be directly damaged by external stimulation. This can occur as an occupational injury owing to contact with organic solvents or other causes. We present cases of eight patients who sustained occupation-related exposure to potentially toxic substances and later presented with signs and symptoms of anosmia. We examined the occupational and medical characteristics of the patients and evaluated their work-relatedness. Case 1: A 50-year-old man performed high-frequency heat treatments for approximately 11 years. He experienced decreased senses for olfaction and taste during the later years culminating in the diagnosis of anosmia after 3 years (high work-relatedness). Case 2: A 54-year-old man whose work involved exposure to various organic solvents, such as spray painting and application of paint and thinners for approximately 4 years, was subsequently diagnosed with anosmia based on rhinorrhea, headache, and loss of olfaction (high work-relatedness). Case 3: A 44-year-old-man who performed spray painting for approximately 17 years developed anosmia (high work-relatedness). Case 4: A 44-year-old man was involved in ship engine cleaning once a month, for approximately 7 h per cleaning session; he was diagnosed with anosmia based on loss of olfaction (low work-relatedness). Case 5: A 41-year-old man worked in ship building block construction for approximately 13 years; anosmia diagnosis was based on loss of olfaction (low work-relatedness). Case 6: A 47-year-old woman performed product inspection and labeling at a plant manufacturing automobile parts; anosmia diagnosis was based on decreased olfaction and taste (low work-relatedness). Case 7: A 50-year-old woman performed epoxy coating in a plant manufacturing automobile parts; anosmia diagnosis was based on diminishing olfaction (low work-relatedness). Case 8: A 57-year-old woman performed cleaning of the area where mobile phone parts were manufactured; anosmia diagnosis was based on diminishing olfaction (low work-relatedness). The study results confirmed work-relatedness when the subject was young, and the duration of exposure was long without any other cause of anosmia. Regarding compensation for occupational diseases, work-relatedness can be recognized as a relative concept.

Challenges in conducting post-authorisation safety studies (PASS): A vaccine manufacturer's view.

PubMed

Cohet, Catherine; Rosillon, Dominique; Willame, Corinne; Haguinet, Francois; Marenne, Marie-Noëlle; Fontaine, Sandrine; Buyse, Hubert; Bauchau, Vincent; Baril, Laurence

2017-05-25

Post-authorisation safety studies (PASS) of vaccines assess or quantify the risk of adverse events following immunisation that were not identified or could not be estimated pre-licensure. The aim of this perspective paper is to describe the authors' experience in the design and conduct of twelve PASS that contributed to the evaluation of the benefit-risk of vaccines in real-world settings. We describe challenges and learnings from selected PASS of rotavirus, malaria, influenza, human papillomavirus and measles-mumps-rubella-varicella vaccines that assessed or identified potential or theoretical risks, which may lead to changes to risk management plans and/or to label updates. Study settings include the use of large healthcare databases and de novo data collection. PASS methodology is influenced by the background incidence of the outcome of interest, vaccine uptake, availability and quality of data sources, identification of the at-risk population and of suitable comparators, availability of validated case definitions, and the frequent need for case ascertainment in large databases. Challenges include the requirement for valid exposure and outcome data, identification of, and access to, adequate data sources, and mitigating limitations including bias and confounding. Assessing feasibility is becoming a key step to confirm that study objectives can be met in a timely manner. PASS provide critical information for regulators, public health agencies, vaccine manufacturers and ultimately, individuals. Collaborative approaches and synergistic efforts between vaccine manufacturers and key stakeholders, such as regulatory and public health agencies, are needed to facilitate access to data, and to drive optimal study design and implementation, with the aim of generating robust evidence. Copyright © 2017 GSK Biologicals SA. Published by Elsevier Ltd.. All rights reserved.

Delivering Value In A Global Aerospace Manufacturer Through The Effective Use Of Numerical Process Simulation

NASA Astrophysics Data System (ADS)

Ward, M. J.; Walløe, S. J.

2004-06-01

Numerical models are used extensively in the aerospace sector to identify appropriate manufacturing parameters, and to minimize the risk associated with new product introduction and manufacturing change. This usage is equally prevalent in original equipment manufacturers (OEMs), and in their supply chains. The wide range of manufacturing processes and production environments involved, coupled with the varying degrees of technology maturity associated with numerical models of different processes leads to a situation of significant complexity from the OEM perspective. In addition, the intended use of simulation technology can vary considerably between applications, from simple geometric assessment of die shape at one extreme, to full process design or development at the other. Consequently there is an increasing trend towards multi-scale modelling, i.e. the use of several different model types, with differing attributes in terms of accuracy and speed to support a range of different new product introduction decisions. This makes the allocation of appropriate levels of activity to the research and implementation of new capabilities a difficult problem. This paper uses a number of industrial cases studies to illustrate a framework for making such allocation decisions such that value to the OEM is maximized, and investigates how such a framework is likely to shift over the next few years based on technological developments.

Energy-efficiency based classification of the manufacturing workstation

NASA Astrophysics Data System (ADS)

Frumuşanu, G.; Afteni, C.; Badea, N.; Epureanu, A.

2017-08-01

EU Directive 92/75/EC established for the first time an energy consumption labelling scheme, further implemented by several other directives. As consequence, nowadays many products (e.g. home appliances, tyres, light bulbs, houses) have an EU Energy Label when offered for sale or rent. Several energy consumption models of manufacturing equipments have been also developed. This paper proposes an energy efficiency - based classification of the manufacturing workstation, aiming to characterize its energetic behaviour. The concept of energy efficiency of the manufacturing workstation is defined. On this base, a classification methodology has been developed. It refers to specific criteria and their evaluation modalities, together to the definition & delimitation of energy efficiency classes. The energy class position is defined after the amount of energy needed by the workstation in the middle point of its operating domain, while its extension is determined by the value of the first coefficient from the Taylor series that approximates the dependence between the energy consume and the chosen parameter of the working regime. The main domain of interest for this classification looks to be the optimization of the manufacturing activities planning and programming. A case-study regarding an actual lathe classification from energy efficiency point of view, based on two different approaches (analytical and numerical) is also included.

Microstructure characterisation of Ti-6Al-4V from different additive manufacturing processes

NASA Astrophysics Data System (ADS)

Neikter, M.; Åkerfeldt, P.; Pederson, R.; Antti, M.-L.

2017-10-01

The focus of this work has been microstructure characterisation of Ti-6Al-4V manufactured by five different additive manufacturing (AM) processes. The microstructure features being characterised are the prior β size, grain boundary α and α lath thickness. It was found that material manufactured with powder bed fusion processes has smaller prior β grains than the material from directed energy deposition processes. The AM processes with fast cooling rate render in thinner α laths and also thinner, and in some cases discontinuous, grain boundary α. Furthermore, it has been observed that material manufactured with the directed energy deposition processes has parallel bands, except for one condition when the parameters were changed, while the powder bed fusion processes do not have any parallel bands.

The economics of telerehabilitation.

PubMed

Dhurjaty, Sreeram

2004-01-01

This paper is an analysis of the economics of physical telerehabilitation, at home, in the clinic, and at work. This study was a precursor to generating a business case for manufacturing telerehabilitation systems. Pilot studies were performed and structured interviews conducted with providers, payers, patients, and employers. The data obtained were analyzed, in conjunction with published data, to understand the economics with respect to parameters such as lost opportunity costs at work, faster rehabilitation, and cost savings to patients, providers, payers, and employers. The results showed that telerehabilitation has a positive business case with respect to all the stakeholders. The ability to quantify and analyze data from patients remotely is convenient and economical to providers. Patients benefit by getting back to their normal activities faster, both at home as well as work. Telerehabilitation at work allows employees to be treated at work without having to take time to go to a clinic. Lost opportunity costs for employers are minimized when workers return to work faster and are treated onsite. The ability to measure progress quantitatively is beneficial for patients, providers, payers, and employers. Additionally, malingering can be detected and eradicated using telerehabilitation. Proper application of appropriate telerehabilitation technologies makes eminent economical sense. There is a strong business case for the application of telerehabilitation, onsite, in large corporations and therefore is profitable to medical device manufacturers.

Applications of dynamic scheduling technique to space related problems: Some case studies

NASA Astrophysics Data System (ADS)

Nakasuka, Shinichi; Ninomiya, Tetsujiro

1994-10-01

The paper discusses the applications of 'Dynamic Scheduling' technique, which has been invented for the scheduling of Flexible Manufacturing System, to two space related scheduling problems: operation scheduling of a future space transportation system, and resource allocation in a space system with limited resources such as space station or space shuttle.

Cooperative Education: Entrepreneurial Development by Colleges and Universities. A Case Study of Oakwood College, Huntsville, Alabama.

ERIC Educational Resources Information Center

Kramer, Frank

The entrepreneurial development and experiential education environments of Oakwood College, Huntsville, Alabama, are described. The college-owned industries of the dairy, farm, garment and linen service, bakery, food manufacturing, convenience store, and snack bar are discussed in terms of markets and marketing, permissions and protections,…

Mathematical String Sculptures: A Case Study in Computationally-Enhanced Mathematical Crafts

ERIC Educational Resources Information Center

Eisenberg, Michael

2007-01-01

Mathematical string sculptures constitute an extremely beautiful realm of mathematical crafts. This snapshot begins with a description of a marvelous (and no longer manufactured) toy called Space Spider, which provided a framework with which children could experiment with string sculptures. Using a computer-controlled laser cutter to create frames…

Agent Regeneration and Hazardous Waste Minimization and Teaching Note. IBM Case Study. Doc #93-1.

ERIC Educational Resources Information Center

Oliker, L. Richard; And Others

The manufacturing process used to produce printbands for International Business Machines, Inc. involves a photolithographic process in which the stainless steel panels are chemically machined using strong ferric chloride etching solution containing hydrochloric acid. The waste material that results from this chemical reaction is a solution…

SOLVENT-BASED TO WATERBASED ADHESIVE-COATED SUBSTRATE RETROFIT - VOLUME IV: FILM AND LABEL MANUFACTURING CASE STUDY: FLEXCON COMPANY, INC.

EPA Science Inventory

This volume discusses a visit to a site operated by FLEXcon Company, Inc., a pressure-sensitive adhesive coater, to collect information on the pollution prevention opportunities and barriers associated with waterbased adhesives. The purpose of the visit to FLEXcon was to gather i...

Technology vs the Academic Book Thief

ERIC Educational Resources Information Center

American School and University, 1972

1972-01-01

Three case studies describe successful installations of three leading book security manufacturers. Reports on a 92 percent book loss cut at West Leyden High School, Northlake, Illinois; a substantial savings and a loss cut at the Charles Stewart Mott Library, Flint, Michigan; and a 75 percent loss cut at Chabot College, Hayward, California. (EA)

Airborne Wind Shear Detection and Warning Systems: Third Combined Manufacturers' and Technologists' Conference, part 1

NASA Technical Reports Server (NTRS)

Vicroy, Dan D. (Compiler); Bowles, Roland L. (Compiler); Schlickenmaier, Herbert (Compiler)

1991-01-01

Papers presented at the conference on airborne wind shear detection and warning systems are compiled. The following subject areas are covered: terms of reference; case study; flight management; sensor fusion and flight evaluation; Terminal Doppler Weather Radar data link/display; heavy rain aerodynamics; and second generation reactive systems.

Correlation of genetic variability with safety of mumps vaccine Urabe AM9 strain.

PubMed

Amexis, G; Fineschi, N; Chumakov, K

2001-08-15

The Urabe AM9 strain of mumps vaccine live is known for its genetic instability and some vaccines derived from this strain were withdrawn from the market due to an excessive number of vaccine-associated parotitis and meningitis cases. To identify the molecular basis of this instability, we determined complete nucleotide sequences of several stocks of the Urabe strain used for vaccine production by different manufacturers and of two clinical isolates from cases of vaccine-associated meningitis. In contrast to previously published studies relating the Lys335 --> Glu mutation in the viral HN gene with neurovirulence of mumps virus, we could not confirm any association of this mutation with the safety of mumps vaccine. Each of the three vaccine stocks studied had its own characteristic profile of mutations that was identified by cDNA sequencing and quantitated by mutant analysis by PCR and restriction enzyme cleavage. Determination of the mutational profile of mumps vaccine lots could allow vaccine manufacturers to characterize seed viruses and monitor the consistency of vaccine production to prevent emergence of virulent revertants.

A cloud-based production system for information and service integration: an internet of things case study on waste electronics

NASA Astrophysics Data System (ADS)

Wang, Xi Vincent; Wang, Lihui

2017-08-01

Cloud computing is the new enabling technology that offers centralised computing, flexible data storage and scalable services. In the manufacturing context, it is possible to utilise the Cloud technology to integrate and provide industrial resources and capabilities in terms of Cloud services. In this paper, a function block-based integration mechanism is developed to connect various types of production resources. A Cloud-based architecture is also deployed to offer a service pool which maintains these resources as production services. The proposed system provides a flexible and integrated information environment for the Cloud-based production system. As a specific type of manufacturing, Waste Electrical and Electronic Equipment (WEEE) remanufacturing experiences difficulties in system integration, information exchange and resource management. In this research, WEEE is selected as the example of Internet of Things to demonstrate how the obstacles and bottlenecks are overcome with the help of Cloud-based informatics approach. In the case studies, the WEEE recycle/recovery capabilities are also integrated and deployed as flexible Cloud services. Supporting mechanisms and technologies are presented and evaluated towards the end of the paper.

Evacuated displacement compression molding

NASA Technical Reports Server (NTRS)

Heier, W. C. (Inventor)

1973-01-01

A process for molding long, thin-wall tubular bodies from thermosetting plastic molding compounds is described. The tubular bodies produced may have body lengths several times the diameters. The application of the process for manufacturing rocket engine cases and nozzles is discussed. The advantages of the system over other methods of circular tube manufacture are analyzed.

75 FR 70775 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-18

... approved collection. Title: Notice 2007-46--Credit for New Medium-Duty and Heavy-Duty Hybrid Motor Vehicles... hybrid vehicles to rely on the domestic manufacturer's (or, in the case of a foreign manufacturer, its... a qualified hybrid motor vehicle under Sec. 30B(3) and (d), and the amount of the credit allowable...

24 CFR 201.23 - Borrower's initial payment.

Code of Federal Regulations, 2010 CFR

2010-04-01

... gift or a loan from some other source, the borrower must disclose the source of such gift or loan on... lender in the loan file. (b) Manufactured home purchase loans. In the case of a manufactured home purchase loan, the borrower shall make a minimum cash downpayment of at least five percent of the purchase...

76 FR 30295 - Airworthiness Directives; SOCATA Model TBM 700 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-25

... case of elevator trim tab actuator jamming once the trim tab arrived to stop. The investigations conducted by the trim tab actuator manufacturer have shown that there was a discrepancy with PRECILEC manufacturing process of elevator trim tab actuator which caused this event. It has been determined as well that...

78 FR 52759 - Foreign-Trade Zone 265-Conroe, Texas: Authorization of Production Activity; Bauer Manufacturing...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-26

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [B-39-2013] Foreign-Trade Zone 265--Conroe, Texas: Authorization of Production Activity; Bauer Manufacturing Inc. (Foundation Casings and Tools/Accessories for Pile Drivers and Boring Machinery), Conroe, Texas On April 18, 2013, the City of Conroe, Texas, grantee...

Can demand-side policies stop the tobacco industry's damage? Lessons from Turkey.

PubMed

Gultekin-Karakas, Derya

2015-01-01

Trade and investment liberalisation in the post-1980 period allowed the penetration of transnational tobacco companies into the Turkish market. State control over the market was gradually removed and tobacco farming, manufacturing, trade and consumption were reshaped in line with the needs of transnational tobacco companies. The resultant increase in product proliferation and aggressive marketing strategies led to a dramatic rise in cigarette consumption in the 1990s, making Turkey a market with one of the sharpest consumption increases in the world. While Turkey implemented demand-side tobacco control policies to reduce consumption after 1996, it continued to stimulate manufacturing and trade in a conflicting way. The Turkish case verifies that the liberalisation process facilitated by the state under the auspices of international institutions conflicts with tobacco control. Liberalisation paves the way for market expansions of transnational tobacco companies that resist tobacco control in their drive for profit. Current global tobacco control policies, with no interest in controlling manufacturing, have limited effect on consumption. The Turkish case indicates the necessity of establishing public control over tobacco manufacturing and trade from a public health perspective.

Implementation workshop of WHO guidelines on evaluation of malaria vaccines: Current regulatory concepts and issues related to vaccine quality, Pretoria, South Africa 07 Nov 2014.

PubMed

Ho, Mei Mei; Baca-Estrada, Maria; Conrad, Christoph; Karikari-Boateng, Eric; Kang, Hye-Na

2015-08-26

The current World Health Organization (WHO) guidelines on the quality, safety and efficacy of recombinant malaria vaccines targeting the pre-erythrocytic and blood stages of Plasmodium falciparum were adopted by the WHO Expert Committee on Biological Standardization in 2012 to provide guidance on the quality, nonclinical and clinical aspects of recombinant malaria vaccines. A WHO workshop was organised to facilitate implementation into African (national/regional) regulatory practices, of the regulatory evaluation principles outlined in the guidelines regarding quality aspects. The workshop was used also to share knowledge and experience on regulatory topics of chemistry, manufacturing and control with a focus on vaccines through presentations and an interactive discussion using a case study approach. The basic principles and concepts of vaccine quality including consistency of production, quality control and manufacturing process were presented and discussed in the meeting. By reviewing and practicing a case study, better understanding on the relationship between consistency of production and batch release tests of an adjuvanted pre-erythrocytic recombinant malaria vaccine was reached. The case study exercise was considered very useful to understand regulatory evaluation principles of vaccines and a suggestion was made to WHO to provide such practices also through its Global Learning Opportunities for Vaccine Quality programme. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

Operations & Maintenance Best Practices - A Guide to Achieving Operational Efficiency (Release 3)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sullivan, Greg; Pugh, Ray; Melendez, Aldo P.

This guide highlights operations and maintenance programs targeting energy and water efficiency that are estimated to save 5% to 20% on energy bills without a significant capital investment. The purpose of this guide is to provide you, the Operations and Maintenance (O&M)/Energy manager and practitioner, with useful information about O&M management, technologies, energy and water efficiency, and cost-reduction approaches. To make this guide useful and to reflect your needs and concerns, the authors met with O&M and Energy managers via Federal Energy Management Program (FEMP) workshops. In addition, the authors conducted extensive literature searches and contacted numerous vendors and industrymore » experts. The information and case studies that appear in this guide resulted from these activities. It needs to be stated at the outset that this guide is designed to provide information on effective O&M as it applies to systems and equipment typically found at Federal facilities. This guide is not designed to provide the reader with step-by-step procedures for performing O&M on any specific piece of equipment. Rather, this guide first directs the user to the manufacturer's specifications and recommendations. In no way should the recommendations in this guide be used in place of manufacturer's recommendations. The recommendations in this guide are designed to supplement those of the manufacturer, or, as is all too often the case, provide guidance for systems and equipment for which all technical documentation has been lost. As a rule, this guide will first defer to the manufacturer's recommendations on equipment operation and maintenance.« less

Asbestos-related occupational cancers compensated under the Industrial Accident Compensation Insurance in Korea.

PubMed

Ahn, Yeon-Soon; Kang, Seong-Kyu

2009-04-01

Compensation for asbestos-related cancers occurring in occupationally-exposed workers is a global issue; this is also an issue in Korea. To provide basic information regarding compensation for workers exposed to asbestos, 60 cases of asbestos-related occupational lung cancer and mesothelioma that were compensated during 15 yr; from 1993 (the year the first case was compensated) to 2007 by the Korea Labor Welfare Corporation (KLWC) are described. The characteristics of the cases were analyzed using the KLWC electronic data and the epidemiologic investigation data conducted by the Occupational Safety and Health Research Institute (OSHRI) of the Korea Occupational Safety and Health Agency (KOSHA). The KLWC approved compensation for 41 cases of lung cancer and 19 cases of mesothelioma. Males accounted for 91.7% (55 cases) of the approved cases. The most common age group was 50-59 yr (45.0%). The mean duration of asbestos exposure for lung cancer and mesothelioma cases was 19.2 and 16.0 yr, respectively. The mean latency period for lung cancer and mesothelioma cases was 22.1 and 22.6 yr, respectively. The major industries associated with mesothelioma cases were shipbuilding and maintenance (4 cases) and manufacture of asbestos textiles (3 cases). The major industries associated with lung cancer cases were shipbuilding and maintenance (7 cases), construction (6 cases), and manufacture of basic metals (4 cases). The statistics pertaining to asbestos-related occupational cancers in Korea differ from other developed countries in that more cases of mesothelioma were compensated than lung cancer cases. Also, the mean latency period for disease onset was shorter than reported by existing epidemiologic studies; this discrepancy may be related to the short history of occupational asbestos use in Korea. Considering the current Korean use of asbestos, the number of compensated cases in Korea is expected to increase in the future but not as much as developed countries.

Reducing uncertainty in value-based pricing using evidence development agreements: the case of continuous intraduodenal infusion of levodopa/carbidopa (Duodopa®) in Sweden.

PubMed

Willis, Michael; Persson, Ulf; Zoellner, York; Gradl, Birgit

2010-01-01

Value-based pricing (VBP), whereby prices are set according to the perceived benefits offered to the consumer at a time when costs and benefits are characterized by considerable uncertainty and are then reviewed ex post, is a much discussed topic in pharmaceutical reimbursement. It is usually combined with coverage with evidence development (CED), a tool in which manufacturers are granted temporary reimbursement but are required to collect and submit additional health economic data at review. Many countries, including the UK, are signalling shifts in this direction. Several countries, including Sweden, have already adopted this approach and offer good insight into the benefits and pitfalls in actual practice. To describe VBP reimbursement decision making using CED in actual practice in Sweden. Decision making by The Dental and Pharmaceutical Benefits Agency (TLV) in Sweden was reviewed using a case study of continuous intraduodenal infusion of levodopa/carbidopa (Duodopa®) in the treatment of advanced Parkinson's disease (PD) with severe motor fluctuations. The manufacturer of Duodopa® applied for reimbursement in late 2003. While the proper economic data were not included in the submission, TLV granted reimbursement until early 2005 to provide time for the manufacturer to submit a formal economic evaluation. The re-submission with economic data was considered inadequate to judge cost effectiveness, so TLV granted an additional extension of reimbursement until August 2007, at which time conclusive data were expected. The manufacturer initiated a 3-year, prospective health economic study and a formal economic model. Data from a pre-planned interim analysis of the data were loaded into the model and the cost-effectiveness ratio was the basis of the next re-submission. TLV concluded that the data were suitable for making a definite decision and that the drug was not cost effective, deciding to discontinue reimbursement for any new patients (current patients were unaffected). The manufacturer continued to collect data and to improve the economic model and re-submitted in 2008. New data and the improved model resulted in reduced uncertainty and a lower cost-effectiveness ratio in the range of Swedish kronor (SEK)430,000 per QALY gained in the base-case analysis, ranging up to SEK900,000 in the most conservative sensitivity analysis, resulting in reimbursement being granted. The case of Duodopa® provides excellent insight into VBP reimbursement decision making in combination with CED and ex post review in actual practice. Publicly available decisions document the rigorous, time-consuming process (four iterations were required before a final decision could be reached). The data generated as part of the risk-sharing agreement proved correct the initial decision to grant limited coverage despite lack of economic data. Access was provided to 100 patients while evidence was generated. Economic appraisal differs from clinical assessment, and decision makers benefit from analysis of naturalistic, actual practice data. Despite reviewing the initial trial-based, 'piggy-back' economic analysis, TLV was uncertain of the cost effectiveness in actual practice and deferred a final decision until observational data from the DAPHNE study became available. Second, acceptance of economic modelling and use of temporary reimbursement conditional on additional evidence development provide a mechanism for risk sharing between TLV and manufacturers, which enabled patient access to a drug with proven clinical benefit while necessary evidence to support claims of cost effectiveness could be generated.

Studies of the use of high-temperature nuclear heat from an HTGR for hydrogen production

NASA Technical Reports Server (NTRS)

Peterman, D. D.; Fontaine, R. W.; Quade, R. N.; Halvers, L. J.; Jahromi, A. M.

1975-01-01

The results of a study which surveyed various methods of hydrogen production using nuclear and fossil energy are presented. A description of these methods is provided, and efficiencies are calculated for each case. The process designs of systems that utilize the heat from a general atomic high temperature gas cooled reactor with a steam methane reformer and feed the reformer with substitute natural gas manufactured from coal, using reforming temperatures, are presented. The capital costs for these systems and the resultant hydrogen production price for these cases are discussed along with a research and development program.

[Fatal occupational accidents in Lombardy].

PubMed

Pianosi, G

1995-01-01

All fatal occupational accidents compensated in Lombardy from 1984 to 1989 were analyzed (1259 cases): significant differences between geographical distribution of fatal occupational accidents and workers were observed. Males accounted for about 95% of fatalities; an excess of cases was shown in both young and elderly workers. Death was the consequence of injuries involving most frequently the head, thorax and spinal cord. An excess of fatalities was observed in agriculture and, at a lower level, in manufacturing industries; small enterprises were involved in approximately 25% of fatalities occurring in the manufacturing industries and services. Employers were the victims of fatal accidents in 50% of cases in agriculture and in 70% of cases in craft industries. Construction, agriculture and transport accounted for about 50% of all fatalities. About 50% of fatal occupational accidents were related to vehicle use: the victim was the driver in the majority of cases, sometimes the victim was run over by a vehicle or fell from a vehicle. The results agree with some previous observations (e.g.: sex and age distribution; construction, agriculture and transport as working activities at high accident risk); but some original observations have emerged, in particular about the frequency of employers as victims and the role of vehicles in the genesis of fatal occupational accidents. If further studies confirm these latter observations, important developments could follow in preventive action design and implementation.

Characterizing synthetic gypsum for wallboard manufacture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henkels, P.J.; Gynor, J.C.

1996-12-31

United States Gypsum Company (USGC) has developed specifications and guidelines covering the chemical and physical aspects of synthetic gypsum to help predict end use acceptability in wallboard manufacture. These guidelines are based in part on past experiences with natural and synthetic gypsum. Similarly, most wallboard manufacturers in North America have developed their own guidelines based in part on its unique history and particular experiences with synthetic gypsum. While there are similarities between manufacturers` guidelines, differences do exist. This paper discusses the importance of selected parameters contained in the FGD gypsum guidelines. In most cases, the parameters are equally relevant tomore » other synthetic gypsums and the naturally occurring gypsum mineral as well.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Plotkowski, A.; Rios, O.; Sridharan, N.

Our present research in metal additive manufacturing (AM) focuses on designing processing parameters around existing alloys designed for traditional manufacturing. However, to maximize the benefits of AM, alloys should be designed to specifically take advantage of the unique thermal conditions of these processes. Furthermore, our study focuses on the development of a design methodology for alloys in AM, using a newly developed Al-Ce alloy as an initial case study. To evaluate the candidacy of this system for fusion based additive manufacturing, single-line laser melts were made on cast Al-12Ce plates using three different beam velocities (100, 200, and 300 mm/min).more » The microstructure was evaluated in the as-melted and heat treated conditions (24 hrs at 300°C). An extremely fine microstructure was observed within the weld pools, evolving from eutectic at the outer solid-liquid boundaries to a primary Al FCC dendritic/cellular structure nearer the melt-pool centerline. We rationalized the observed microstructures through the construction of a microstructure selection map for the Al-Ce binary system, which will be used to enable future alloy design. Interestingly, the heat treated samples exhibited no microstructural coarsening.« less

Tools and Strategies for Product Life Cycle Management ñ A Case Study in Foundry

NASA Astrophysics Data System (ADS)

Patil, Rajashekar; Kumar, S. Mohan; Abhilash, E.

2012-08-01

Advances in information and communication technology (ICT) have opened new possibilities of collaborations among the customers, suppliers, manufactures and partners to effectively tackle various business challenges. Product Life Cycle Management(PLM) has been a proven approach for Original Equipment Manufacturers (OEMs) to increase their productivity, improve their product quality, speed up delivery, and increase their profit and to become more efficient. However, their Tier 2 and Tier 3 suppliers like foundry industries are still in their infancy without adopting PLM. Hence to enhance their understanding, the basic concepts, the tools and strategies for PLM are presented is this paper. By selecting and implementing appropriate PLM strategies in a small foundry, an attempt was also made to understand the immediate benefits of using PLM tools (commercial PLM software and digital manufacturing tools). This study indicated a reduction in lead time and improved utilization of organizational resources in the production of automobile impeller. These observations may be further extrapolated to other multiproduct, multi-discipline and multi-customer companies to realize the advantages of using PLM technology

Scanning electron microscopic characteristics of commercially available 1- and 3-piece intraocular lenses.

PubMed

Brockmann, Tobias; Brockmann, Claudia; Nietzsche, Sandor; Bertelmann, Eckart; Strobel, Juergen; Dawczynski, Jens

2013-12-01

To evaluate commercially available 1- and 3-piece intraocular lenses (IOLs) with scanning electron microscopy (SEM). Department of Ophthalmology and Electron Microscopy Center, University Hospital Jena, Jena, Germany. Experimental study. Seven +23.0 diopter IOLs of different design and material and from different manufacturers were chosen for a detailed assessment. Scanning electron microscopy was used at standardized magnifications to assess typical IOL characteristics. The particular focus was the optic edge, the optic surface, the haptic–optic junction, and the haptic. All square-edged IOLs had a curvature radius of less than 10 μm, while the mean optic edge thickness ranged between 216 μm and 382 μm. A 360-degree square-edged boundary was present in all 3-piece IOLs and in a single 1-piece model. Relevant production remnants on the optic edge were observed in 1 case. Regarding the haptic, 3-piece IOLs had uniformly shaped fibers with a mean thickness of 177 μm ± 51 (SD) (range 116 to 220 μm). Chemical adhesives were used to attach the haptic in 1 case, where alterations of the IOL material were observed. In another case, the haptic fiber was press-fitted into the optic, which resulted in bulging of the optic profile. Inspection of surface characteristics showed wavelike patterns in 2 IOLs. Taking clinical relevance into account, all IOLs were of high manufacturing quality. Certain attention was paid in creating a sharp optic edge. Surface irregularities of 2 IOLs were attributed to the manufacturing technique. Methods for implementing the haptic–optic junction were diverse.

The Role of the Manufacturer in Air Transportation Planning

NASA Technical Reports Server (NTRS)

Mackenzie, J.

1972-01-01

The role of the aircraft manufacturer in the airline industry is considered. The process is illustrated by using a fictitious airline as an example--that is, a case study approach with Mid-Coast Airways serving as the example. Both in slide form and with supporting papers, a brief history of the airline, a description of its route structure and a forecast based on econometric analysis are presented. Once the forecast rationale is explained, information outlines the requirements for additional aircraft and the application of new aircraft across the system using alternative fleet plan options. The fleet plan is translated into financial summaries which indicate the relative merit of alternative aircraft types or operating plans.

Manufacture and use of home made ophthalmoscopes: a 150th anniversary tribute to Helmholtz

PubMed Central

Armour, Roger H

2000-01-01

Objective To produce a simple, effective, and inexpensive training ophthalmoscope. Design Case study. Setting A coffee table in a sitting room and an eye clinic. Participants 10 friends and relatives, several patients, and a cooperative Persian cat. Interventions Direct ophthalmoscopy with instrument made with easily available material and tools from art and office equipment shops. Main outcome measures Efficiency, clarity of view, and price of ophthalmoscope. Results The instrument was readily made; of the 50 manufactured two thirds gave a good view; and each cost less than £1 to make. Conclusion The ophthalmoscope is fun to make, works well, and anyone can make one. PMID:11124172

Trends in Process Analytical Technology: Present State in Bioprocessing.

PubMed

Jenzsch, Marco; Bell, Christian; Buziol, Stefan; Kepert, Felix; Wegele, Harald; Hakemeyer, Christian

2017-08-04

Process analytical technology (PAT), the regulatory initiative for incorporating quality in pharmaceutical manufacturing, is an area of intense research and interest. If PAT is effectively applied to bioprocesses, this can increase process understanding and control, and mitigate the risk from substandard drug products to both manufacturer and patient. To optimize the benefits of PAT, the entire PAT framework must be considered and each elements of PAT must be carefully selected, including sensor and analytical technology, data analysis techniques, control strategies and algorithms, and process optimization routines. This chapter discusses the current state of PAT in the biopharmaceutical industry, including several case studies demonstrating the degree of maturity of various PAT tools. Graphical Abstract Hierarchy of QbD components.

Implementation of activity-based costing (ABC) to drive cost reduction efforts in a semiconductor manufacturing operation

NASA Astrophysics Data System (ADS)

Naguib, Hussein; Bol, Igor I.; Lora, J.; Chowdhry, R.

1994-09-01

This paper presents a case study on the implementation of ABC to calculate the cost per wafer and to drive cost reduction efforts for a new IC product line. The cost reduction activities were conducted through the efforts of 11 cross-functional teams which included members of the finance, purchasing, technology development, process engineering, equipment engineering, production control, and facility groups. The activities of these cross functional teams were coordinated by a cost council. It will be shown that these activities have resulted in a 57% reduction in the wafer manufacturing cost of the new product line. Factors contributed to successful implementation of an ABC management system are discussed.

Innovations in Advanced Materials and Metals Manufacturing Project (IAM2)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott, Elizabeth

This project, under the Jobs and Innovation Accelerator Challenge, Innovations in Advanced Materials and Metals Manufacturing Project, contracted with Cascade Energy to provide a shared energy project manager engineer to work with five different companies throughout the Portland metro grant region to implement ten energy efficiency projects and develop a case study to analyze the project model. As a part of the project, the energy project manager also looked into specific new technologies and methodologies that could change the way energy is consumed by manufacturers—from game-changing equipment and technology to monitor energy use to methodologies that change the way companiesmore » interact and use their machines to reduce energy consumption.« less

Production scheduling with ant colony optimization

NASA Astrophysics Data System (ADS)

Chernigovskiy, A. S.; Kapulin, D. V.; Noskova, E. E.; Yamskikh, T. N.; Tsarev, R. Yu

2017-10-01

The optimum solution of the production scheduling problem for manufacturing processes at an enterprise is crucial as it allows one to obtain the required amount of production within a specified time frame. Optimum production schedule can be found using a variety of optimization algorithms or scheduling algorithms. Ant colony optimization is one of well-known techniques to solve the global multi-objective optimization problem. In the article, the authors present a solution of the production scheduling problem by means of an ant colony optimization algorithm. A case study of the algorithm efficiency estimated against some others production scheduling algorithms is presented. Advantages of the ant colony optimization algorithm and its beneficial effect on the manufacturing process are provided.

Additive Manufacturing Techniques for the Reconstruction of 3D Fetal Faces.

PubMed

Speranza, Domenico; Citro, Daniela; Padula, Francesco; Motyl, Barbara; Marcolin, Federica; Calì, Michele; Martorelli, Massimo

2017-01-01

This paper deals with additive manufacturing techniques for the creation of 3D fetal face models starting from routine 3D ultrasound data. In particular, two distinct themes are addressed. First, a method for processing and building 3D models based on the use of medical image processing techniques is proposed. Second, the preliminary results of a questionnaire distributed to future parents consider the use of these reconstructions both from an emotional and an affective point of view. In particular, the study focuses on the enhancement of the perception of maternity or paternity and the improvement in the relationship between parents and physicians in case of fetal malformations, in particular facial or cleft lip diseases.

Battery resource assessment. Subtask 2.5: Battery manufacturing capability recycling of battery materials

NASA Astrophysics Data System (ADS)

Pemsler, P.

1981-02-01

Studies were conducted on the recycling of advanced battery system components for six different battery systems. These include: nickel/zinc, nickel/iron, zinc/chlorine, zinc/bromine, sodium/sulfur, and lithium-aluminum/iron sulfide. For each battery system, one or more processes were developed which would permit recycling of the major or active materials. Each recycle process was designed to produce a product material which can be used directly as a raw material by the battery manufacturer. Metal recoverabilities are in the range of 93 to 95% for all processes. In each case, capital and operating costs were developed for a recycling plant which processes 100,000 electric vehicle batteries per year.

Litigation involving DES.

PubMed

Rheingold, P D

1976-01-01

Focus is on the diethylstilbestrol (DES) litigation which has resulted from the 1971 discovery that this synthetic estrogen can cause cancer in the daughters of women who used the drug during pregnancy in an effort to prevent threatened abortion. Possibly 100 suits are pending at this time in which DES daughters claim injuries. In most of these vaginal or cervical cancer has appeared -- with or without a hysterectomy having been performed. Several women died from cancer. The fact that the use of DES occurred many years ago is the legal hurdle most troublesome to lawyers. The average women coming to a lawyer's office today has a mother who used some form of DES, perhaps in 1955. Few drugstores have records today of the prescriptions which they filled 20 years ago. It has been estimated that over the 1950-1970 period more than 200 different companies manufactured or "tabletized" under their own name DES plus a variety of similar synthetic estrogens promoted for the prevention of threatened abortion. A further hurdle caused by the passage of time is that even the records of the physicians are frequently lost. A final problem created by the age of the cases is statute of limitations. If the actual manufacturer of the DES cannot be identified, this is generally the end of the lawyer's interest in the case. The chance of the plaintiff winning may be increased if the action against all the manufacturers is a class action. Most of the pending DES suits are against the manufacturer and not against the doctor. Thus far no DES case has been tried to completion. Several have been settled by the manufacturers on the eve of the trial, generally for less than the full sum that a cancer victim would expect to receive.

A preliminary 'test case' manufacturing sequence for 50 cents/watt solar photovoltaic modules in 1986

NASA Technical Reports Server (NTRS)

Bickler, D. B.

1979-01-01

The paper describes a 'test case' manufacturing process sequence for solar photovoltaic modules which will cost 50 cents/watt in 1986. The process, which starts with the purification of silicon grown into 75-mm-wide thin ribbons, is discussed, and the plant layout is depicted; each department is sized to produce 250 MW of modules/per year. The cost of this process sequence is compared to present technology at various companies showing considerable spread for each process; data are tabulated in a composite state-of-the-art cell processing cost summary for these processes.

n-Hexane polyneuropathy in a ball-manufacturing factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, C.C.; Shih, T.S.; Cheng, S.Y.

Five overt and two occult cases of n-hexane polyneuropathy occurred in a ball-manufacturing factory in Taiwan. The severity of polyneuropathy was directly related to the index of n-hexane exposure that occurred during the processes of cement coating and nylon fiber winding in a poorly ventilated room. The n-hexane concentrations over eight hours of personal sampling of the air of the cement coating and nylon fiber winding areas were 109 ppm and 86 ppm, respectively. After installation of a new factory ventilation system, these seven patients recovered completely, and there were no new cases in the two-year follow-up.

26 CFR 48.4216(d)-1 - Sales of installment accounts.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 26 Internal Revenue 16 2011-04-01 2011-04-01 false Sales of installment accounts. 48.4216(d)-1... Manufacturers Taxes § 48.4216(d)-1 Sales of installment accounts. (a) In general. Except as provided in paragraph (d) of this section, in case of a sale or other disposition by a manufacturer, producer, or...

26 CFR 48.4216(d)-1 - Sales of installment accounts.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 16 2010-04-01 2010-04-01 true Sales of installment accounts. 48.4216(d)-1... Manufacturers Taxes § 48.4216(d)-1 Sales of installment accounts. (a) In general. Except as provided in paragraph (d) of this section, in case of a sale or other disposition by a manufacturer, producer, or...

Consumer ring count and grain texture preferences of selected eastern United States hardwoods

Treesearch

Delton Alderman; Matthew Bumgardner; Scott Bowe; David Brinberg

2008-01-01

Historically, eastern hardwoods have been a staple of forest products production. However, hardwood producers are now faced with serious challenges from substitutable products, such as imports of foreign species, utilization of foreign species in overseas manufacture (e.g., case goods, etc.), and composite-based materials that are imported or manufactured here in the...

77 FR 6822 - Notice of Lodging of Consent Decree Under the Clean Air Act

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-09

... Manufacturing, Inc. Case No. 4:12-cv-00471-DMR, was lodged with the United States District Court for the... relief against Columbus Manufacturing Inc. (``CMI'') for violations of Section 112(r)(1) and 112(r)(7) of... (``EPCRA''), with respect to CMI's two meat processing facilities located in South San Francisco and...

27 CFR 53.91 - Charges to be included in sale price.

Code of Federal Regulations, 2010 CFR

2010-04-01

... the Code and § 53.100. In the case of sales on credit, a carrying, finance, or service charge is... connection with collection). (b) Tools and dies. Separate charges for tools and dies used in the manufacture... manufacture taxable articles, the tools and dies used in production pass to the purchaser, only the amount of...

19 CFR 19.15 - Withdrawal for exportation of articles manufactured in bond; waste or byproducts for consumption.

Code of Federal Regulations, 2010 CFR

2010-04-01

... direct exportation, unless an authorization of the manufacturer is endorsed on the face of the withdrawal... be required as in the case of other warehouse withdrawals for exportation. (l) When the fact of... 19 Customs Duties 1 2010-04-01 2010-04-01 false Withdrawal for exportation of articles...

Evaluation of workers' exposure to methylene diphenyl diisocyanate (MDI) in an automobile manufacturing company, Iran.

PubMed

Kakooei, Hossein; Shahtaheri, Seyed Jamaleddin; Karbasi, Hossein-Ali

2006-01-01

Evaluation of personal inhalation exposure to methylene diphenyl diisocyanate (MDI) among 39 employees, working in the window fixation and window glue processes in an automobile manufacturing company was performed. This study was conducted for both case and control groups. After sampling and sample preparation processes, MDI was determined with a UV-VIS spectrophotometer at 590 nm; the lung function was assessed with a digital spirometer, too. The average concentration of MDI in the window fixation, and window glue workplaces were 34.53 and 27.37 micro g/m3, respectively, which was lower than the threshold limit value (TLV) recommended by the American Conference of Governmental Industrial Hygienists (ACGIH) (51 micro g/m3). Respiratory symptoms in the exposed group were significantly different compared to the unexposed group (p < .05). Lung capacities in the case group were lower than in the control group (p < .05). Therefore, MDI can be easily measured making it possible to evaluate the adverse effects caused by occupational exposure.

Sustainable development strategies in international business: The case of resource-based firms in the Andean Region of Latin America

NASA Astrophysics Data System (ADS)

Garcia, Percy Luis

This research possesses four relevant characteristics with a potential to contribute to the international business literature. First, it was conducted in three Latin American countries: Peru, Chile and Ecuador (emerging economies) where little research in international business, in comparison with other regions, has been conducted. Second, it was conducted in two industries: mining and oil and gas, which have different ways of organizing and operating in comparison with production and manufacturing industries. Third, it was conducted in remote and sensitive environmental and social areas, where stakeholders and their concerns are different from those of production and manufacturing industries. And fourth, it integrates sustainable development strategies into the field of international business. This thesis provides an in-depth discussion of three case studies and presents conclusions and implications for theory development, managers, and policy makers. The purpose of this research is to contribute to mainstream of the literature on international business by describing and analyzing the incorporation of sustainable development into management strategies.

Cost model relationships between textile manufacturing processes and design details for transport fuselage elements

NASA Technical Reports Server (NTRS)

Metschan, Stephen L.; Wilden, Kurtis S.; Sharpless, Garrett C.; Andelman, Rich M.

1993-01-01

Textile manufacturing processes offer potential cost and weight advantages over traditional composite materials and processes for transport fuselage elements. In the current study, design cost modeling relationships between textile processes and element design details were developed. Such relationships are expected to help future aircraft designers to make timely decisions on the effect of design details and overall configurations on textile fabrication costs. The fundamental advantage of a design cost model is to insure that the element design is cost effective for the intended process. Trade studies on the effects of processing parameters also help to optimize the manufacturing steps for a particular structural element. Two methods of analyzing design detail/process cost relationships developed for the design cost model were pursued in the current study. The first makes use of existing databases and alternative cost modeling methods (e.g. detailed estimating). The second compares design cost model predictions with data collected during the fabrication of seven foot circumferential frames for ATCAS crown test panels. The process used in this case involves 2D dry braiding and resin transfer molding of curved 'J' cross section frame members having design details characteristic of the baseline ATCAS crown design.

Developing a Template for Electronic Portfolios in Career and Technical Education

ERIC Educational Resources Information Center

Fowler, Matthew

2012-01-01

The purposes of this multiple case study were to determine if manufacturing and services sector employers found value in the use of an ePortfolio in the hiring process, and to develop a suggested template for an ePortfolio format to be used within career and technical education. Electronic portfolios "allow students to showcase their…

System Simulation Modeling: A Case Study Illustration of the Model Development Life Cycle

Treesearch

Janice K. Wiedenbeck; D. Earl Kline

1994-01-01

Systems simulation modeling techniques offer a method of representing the individual elements of a manufacturing system and their interactions. By developing and experimenting with simulation models, one can obtain a better understanding of the overall physical system. Forest products industries are beginning to understand the importance of simulation modeling to help...

A Can of Bull? Do Energy Drinks Really Provide a Source of Energy?

ERIC Educational Resources Information Center

Heidemann, Merle; Urquhart, Gerald R.

2005-01-01

This case study involves the biochemical analysis of the components of commonly available energy drinks, which many students purchase at fairly high prices. Students research the ingredients in each product and their physiological role in the human body, and then attempt to match what they learn with the product manufacturers' marketing claims.…

Effect of Foreign Presence on Domestic Performance: The Cases of Education in the US and Manufacturing Firms in Ethiopia

ERIC Educational Resources Information Center

Abegaz, Melaku

2016-01-01

This dissertation studies the effects of foreign presence on the performance of domestic institutions and economic agents. We identify three types of foreign presence: international students, inward foreign investment, and exporting activities. The first chapter investigates the impacts of international students on the graduation performance of…

A joint labor-management hazard communication training program: a case study in worker health and safety training.

PubMed

Robins, T G; Hugentobler, M K; Kaminski, M; Klitzman, S

1994-01-01

The 1983 OSHA Hazard Communication Standard requires training of employees exposed to hazardous chemicals. The authors provide a detailed look at the successes and failures of a joint labor-management training program that was designed to bring a firm with more than 50 manufacturing facilities into compliance with the standard.

Distribution of Employment Growth in 10 Ozark Communities. A Case Study.

ERIC Educational Resources Information Center

Oliveira, Victor J.; Kuehn, John A.

Service industries, some manufacturing, and a concentration of retirees can provide a strong economic base in a rural area. Rapid growth of service businesses, especially wholesale and retail firms and other businesses related to tourism and recreation, attracted job-seekers to a 10-county area in the Ozark Mountains of Arkansas and Missouri…

Rural Industrialization: Case Study of a Tissue Paper Mill in Pickens, Mississippi.

ERIC Educational Resources Information Center

Crecink, John C.

The shortrun (1962-1966) economic impact of a tissue paper mill in Pickens, Mississippi, a town of under 1,000 in a depressed rural area with a predominance of poor Negroes, was analyzed. The tissue mill began in a building formerly occupied by a North Carolina furniture manufacturer. Initial financing came from the Area Redevelopment…

Promising Practices in Young Adult Employment: Lessons Learned from Manufacturing and Automotive Career Pathway Programs

ERIC Educational Resources Information Center

Wagner, Stacey

2015-01-01

The National Fund's Young Adult Initiatives aim to test and implement new strategies for targeting America's young adults and share this information so that employers and workforce development can join forces in investing in the millions of young adults across the nation. This case study focuses on promising findings from automotive and…

Commercial Parts Technology Qualification Processes

NASA Technical Reports Server (NTRS)

Cooper, Mark S.

2013-01-01

Many high-reliability systems, including space systems, use selected commercial parts (including Plastic Encapsulated Microelectronics or PEMs) for unique functionality, small size, low weight, high mechanical shock resistance, and other factors. Predominantly this usage is subjected to certain 100% tests (typically called screens) and certain destructive tests usually (but not always) performed on the flight lot (typically called qualification tests). Frequently used approaches include those documented in EEE-INST-002 and JPL DocID62212 (which are sometimes modified by the particular aerospace space systems manufacturer). In this study, approaches from these documents and several space systems manufacturers are compared to approaches from a launch systems manufacturer (SpaceX), an implantable medical electronics manufacturer (Medtronics), and a high-reliability transport system process (automotive systems). In the conclusions section, these processes are outlined for all of these cases and presented in tabular form. Then some simple comparisons are made. In this introduction section, the PEM technology qualification process is described, as documented in EEE-INST-002 (written by the Goddard Space Flight Center, GSFC), as well as the somewhat modified approach employed at the Jet Propulsion Laboratory (JPL). Approaches used at several major NASA contractors are also described

Improved turbopump dynamics

NASA Technical Reports Server (NTRS)

Kiefling, L.

1985-01-01

A study was initiated to investigate the practicality of increasing rotor critical speeds by changes in manufacturing method. The technique would be to build a pump with an all laser welded shaft and case; such unit to be opened by laser cutting and rebuilt by rewelding the same surface. Use of a split casing, common in industry, would permit assembly of the rotor outside the case. A team was formed to perform the study; however, the work of the team was severely restricted by conflict with higher priority tasks. No manpower was available to evaluate alternate configurations. Thus, much of the synergetic effects of cohesive design modification was lost. Although very limited results were achieved, nothing was found to indicate that the method is not worth further investigation.

Effects of Defects in Laser Additive Manufactured Ti-6Al-4V on Fatigue Properties

NASA Astrophysics Data System (ADS)

Wycisk, Eric; Solbach, Andreas; Siddique, Shafaqat; Herzog, Dirk; Walther, Frank; Emmelmann, Claus

Laser Additive Manufacturing (LAM) enables economical production of complex lightweight structures as well as patient individual implants. Due to these possibilities the additive manufacturing technology gains increasing importance in the aircraft and the medical industry. Yet these industries obtain high quality standards and demand predictability of material properties for static and dynamic load cases. However, especially fatigue and crack propagation properties are not sufficiently determined. Therefore this paper presents an analysis and simulation of crack propagation behavior considering Laser Additive Manufacturing specific defects, such as porosity and surface roughness. For the mechanical characterization of laser additive manufactured titanium alloy Ti-6Al-4V, crack propagation rates are experimentally determined and used for an analytical modeling and simulation of fatigue. Using experimental results from HCF tests and simulated data, the fatigue and crack resistance performance is analyzed considering material specific defects and surface roughness. The accumulated results enable the reliable prediction of the defects influence on fatigue life of laser additive manufactured titanium components.

Safety of laboratory analyzers for infection testing - results of the market surveillance by the BfArM until end 2007

PubMed Central

2009-01-01

The European Directive 98/79/EC on in vitro diagnostic medical devices (IVD) stipulates the marketing and post market surveillance of IVD in the European Economic Area. In cases of issues and field corrective actions, the manufacturers have to inform the responsible Competent Authorities (CA). In Germany, the Federal Institute for Drugs and Medical Devices (BfArM) is the responsible CA for most IVD, with a small subset of IVD for immune hematological and infectiological testing as well as tissue typing as specified in Annex II of the Directive, being within the responsibility of the Paul-Ehrlich-Institute (PEI). In this study, all issues regarding laboratory analyzers for infection testing and their consumables, but not reagents, kits and general culture media, reported to the BfArM between begin 1999 and end of 2007 were analyzed in respect to the sources of report, the underlying product failure and the performed corrective actions. Within the observation period a total of 1471 reports for IVD were received of which 73 related to the IVD for infection testing were included in our study. Reports were predominantly received from manufacturers (56) and competent authorities (15). Affected products were most frequently those for immunological analysis (42) whereas those based on culturing techniques (17) and molecular biological techniques (14) played only minor roles. In all these groups, laboratory analyzers (55) were more frequently affected than their consumables (18). Investigations of the manufacturers were able to identify the underlying root causes of product failures in 62 cases (84.9%). In 2 cases (2.7%) the root cause remained unclear and in 9 cases (12.3%) a product failure was excluded or a user error was the underlying cause. Product failures in laboratory analyzers were most frequently caused by software errors (31) and constructional faults (8) whereas the predominant cause of product failure in consumables were errors in production and quality control (8). Manufacturers issued corrective measures in 66 cases (90.4%) from which 49 and 17 were related to laboratory analyzers and their consumables, respectively. Based on the underlying root causes of product failures these were predominantly customer information (48), recalls (40), software-updates (30) and design changes (9) in the product group of laboratory analyzers as well as customer information (16), recalls (12) and modifications of production and quality management (11) in the group of consumables. The results and experiences obtained since 1999 suggest that the system for post marketing surveillance of IVD is an established tool to ensure product safety, even though the current system can be further enhanced. PMID:20156760

Impact of a financial risk-sharing scheme on budget-impact estimations: a game-theoretic approach.

PubMed

Gavious, Arieh; Greenberg, Dan; Hammerman, Ariel; Segev, Ella

2014-06-01

As part of the process of updating the National List of Health Services in Israel, health plans (the 'payers') and manufacturers each provide estimates on the expected number of patients that will utilize a new drug. Currently, payers face major financial consequences when actual utilization is higher than the allocated budget. We suggest a risk-sharing model between the two stakeholders; if the actual number of patients exceeds the manufacturer's prediction, the manufacturer will reimburse the payers by a rebate rate of α from the deficit. In case of under-utilization, payers will refund the government at a rate of γ from the surplus budget. Our study objective was to identify the optimal early estimations of both 'players' prior to and after implementation of the risk-sharing scheme. Using a game-theoretic approach, in which both players' statements are considered simultaneously, we examined the impact of risk-sharing within a given range of rebate proportions, on players' early budget estimations. When increasing manufacturer's rebate α to be over 50 %, then manufacturers will announce a larger number, and health plans will announce a lower number of patients than they would without risk sharing, thus substantially decreasing the gap between their estimates. Increasing γ changes players' estimates only slightly. In reaction to applying a substantial risk-sharing rebate α on the manufacturer, both players are expected to adjust their budget estimates toward an optimal equilibrium. Increasing α is a better vehicle for reaching the desired equilibrium rather than increasing γ, as the manufacturer's rebate α substantially influences both players, whereas γ has little effect on the players behavior.

A Comparative Case Study Analysis of Administrators Perceptions on the Adaptation of Quality and Continuous Improvement Tools to Community Colleges in the State of Michigan

ERIC Educational Resources Information Center

Mattis, Ted B.

2011-01-01

The purpose of this study was to determine whether community college administrators in the state of Michigan believe that commonly known quality and continuous improvement tools, prevalent in a manufacturing environment, can be adapted to a community college model. The tools, specifically Six Sigma, benchmarking and process mapping have played a…

Development of a skull/brain model for military wound ballistics studies.

PubMed

Carr, Debra; Lindstrom, Anne-Christine; Jareborg, Andreas; Champion, Stephen; Waddell, Neil; Miller, David; Teagle, Michael; Horsfall, Ian; Kieser, Jules

2015-05-01

Reports on penetrating ballistic head injuries in the literature are dominated by case studies of suicides; the penetrating ammunition usually being .22 rimfire or shotgun. The dominating cause of injuries in modern warfare is fragmentation and hence, this is the primary threat that military helmets protect the brain from. When helmets are perforated, this is usually by bullets. In combat, 20% of penetrating injuries occur to the head and its wounding accounts for 50% of combat deaths. A number of head simulants are described in the academic literature, in ballistic test methods for helmets (including measurement of behind helmet blunt trauma, BHBT) and in the 'open' and 'closed' government literature of several nations. The majority of these models are not anatomically correct and are not assessed with high-velocity rifle ammunition. In this article, an anatomically correct 'skull' (manufactured from polyurethane) and 'brain' (manufactured from 10%, by mass, gelatine) model for use in military wound ballistic studies is described. Filling the cranium completely with gelatine resulted in a similar 'skull' fracture pattern as an anatomically correct 'brain' combined with a representation of cerebrospinal fluid. In particular, posterior cranial fossa and occipital fractures and brain ejection were observed. This pattern of injury compared favourably to reported case studies of actual incidents in the literature.

Case study on risk evaluation of printed electronics using nanosilver ink.

PubMed

Kim, Ellen; Lee, Ji Hyun; Kim, Jin Kwon; Lee, Gun Ho; Ahn, Kangho; Park, Jung Duck; Yu, Il Je

2016-01-01

With the ever-increasing development of nanotechnology, our society is being surrounded by possible risks related to exposure to manufactured nanomaterials. The consumer market already includes many products that contain silver nanoparticles (AgNPs), including various household products, such as yoga mats, cutting boards, running shirts, and socks. There is a growing concern over the release of AgNPs in workplaces related to the manufacture and application of nanomaterials. This study investigated the release of AgNPs during the operation of a printed electronics printer. Using an exposure simulation chamber, a nanoparticle collector, scanning mobility particle sizer (SMPS), condensation particle counter (CPC), dust monitor, and mixed cellulose ester (MCE) filters are all connected to measure the AgNP exposure levels when operating a printed electronics printer. A very small amount of AgNPs was released during the operation of the printed electronics printer, and the number of AgNPs inside the exposure simulation chamber was lower than that outside background. In addition, when evaluating the potential risks for consumers and workers using a margin of exposure (MOE) approach and target MOE of 1000, the operational results far exceeded the target MOE in this simulation study and in a previous workplace exposure study. The overall results indicate a no-risk concern level in the case of printed electronics using nanosilver ink.

Safety, effectiveness and comparability of professional skin cleansers.

PubMed

Terhaer, Flora K; Bock, Meike; Fartasch, Manigé; Gabard, Bernard; Elsner, Peter; Kleesz, Peter; Landeck, Lilla; Pohrt, Ute; Seyfarth, Florian; Schliemann, Sibylle; Diepgen, Thomas L; Zagrodnik, Fred; John, Swen Malte

2010-10-01

There are no widely-accepted methodical specifications with which to objectify cleansing effectiveness and skin compatibility of occuptional skin cleansing products in Europe. Therefore the German Social Insurance Agency (DGUV) initiated a study with the goal to evaluate such products in view of the potency and the safety of hand cleansers. A market analysis was a part of the project. The product descriptions and safety data sheets of 120 products (5-20/manufacturer) of 11 manufacturers were evaluated between 02/2008 and 04/2008. The manufacturers used mainly ingredients of low irritancy. The declaration of the applied ingredients was in the majority of the cases correctly labeled according to the INCI Declaration. Although there was documentation of skin tolerability for most products, the manufacturers used widely differing tests of skin compatibility. Evidences for cleansing effectiveness were not declared or have not been provided. One manufacturer even promised medical effects of its products. There was no uniform general classification of products making it difficult to identify characteristics of cleansers and choose between them. Presently, there are no commonly accepted criteria to classify products in view of cleansing effectiveness und skin compatibility. Generally accepted criteria and test methods are needed for the evaluation of hand cleansers in order to provide the possibility of transparency and comparability. © The Authors • Journal compilation © Blackwell Verlag GmbH, Berlin.

Equipment failures and their contribution to industrial incidents and accidents in the manufacturing industry.

PubMed

Bourassa, Dominic; Gauthier, François; Abdul-Nour, Georges

2016-01-01

Accidental events in manufacturing industries can be caused by many factors, including work methods, lack of training, equipment design, maintenance and reliability. This study is aimed at determining the contribution of failures of commonly used industrial equipment, such as machines, tools and material handling equipment, to the chain of causality of industrial accidents and incidents. Based on a case study which aimed at the analysis of an existing pulp and paper company's accident database, this paper examines the number, type and gravity of the failures involved in these events and their causes. Results from this study show that equipment failures had a major effect on the number and severity of accidents accounted for in the database: 272 out of 773 accidental events were related to equipment failure, where 13 of them had direct human consequences. Failures that contributed directly or indirectly to these events are analyzed.

Methodology for designing and manufacturing complex biologically inspired soft robotic fluidic actuators: prosthetic hand case study.

PubMed

Thompson-Bean, E; Das, R; McDaid, A

2016-10-31

We present a novel methodology for the design and manufacture of complex biologically inspired soft robotic fluidic actuators. The methodology is applied to the design and manufacture of a prosthetic for the hand. Real human hands are scanned to produce a 3D model of a finger, and pneumatic networks are implemented within it to produce a biomimetic bending motion. The finger is then partitioned into material sections, and a genetic algorithm based optimization, using finite element analysis, is employed to discover the optimal material for each section. This is based on two biomimetic performance criteria. Two sets of optimizations using two material sets are performed. Promising optimized material arrangements are fabricated using two techniques to validate the optimization routine, and the fabricated and simulated results are compared. We find that the optimization is successful in producing biomimetic soft robotic fingers and that fabrication of the fingers is possible. Limitations and paths for development are discussed. This methodology can be applied for other fluidic soft robotic devices.

Design of forging process variables under uncertainties

NASA Astrophysics Data System (ADS)

Repalle, Jalaja; Grandhi, Ramana V.

2005-02-01

Forging is a complex nonlinear process that is vulnerable to various manufacturing anomalies, such as variations in billet geometry, billet/die temperatures, material properties, and workpiece and forging equipment positional errors. A combination of these uncertainties could induce heavy manufacturing losses through premature die failure, final part geometric distortion, and reduced productivity. Identifying, quantifying, and controlling the uncertainties will reduce variability risk in a manufacturing environment, which will minimize the overall production cost. In this article, various uncertainties that affect the forging process are identified, and their cumulative effect on the forging tool life is evaluated. Because the forging process simulation is time-consuming, a response surface model is used to reduce computation time by establishing a relationship between the process performance and the critical process variables. A robust design methodology is developed by incorporating reliability-based optimization techniques to obtain sound forging components. A case study of an automotive-component forging-process design is presented to demonstrate the applicability of the method.

Underwater Calibration of Dome Port Pressure Housings

NASA Astrophysics Data System (ADS)

Nocerino, E.; Menna, F.; Fassi, F.; Remondino, F.

2016-03-01

Underwater photogrammetry using consumer grade photographic equipment can be feasible for different applications, e.g. archaeology, biology, industrial inspections, etc. The use of a camera underwater can be very different from its terrestrial use due to the optical phenomena involved. The presence of the water and camera pressure housing in front of the camera act as additional optical elements. Spherical dome ports are difficult to manufacture and consequently expensive but at the same time they are the most useful for underwater photogrammetry as they keep the main geometric characteristics of the lens unchanged. Nevertheless, the manufacturing and alignment of dome port pressure housing components can be the source of unexpected changes of radial and decentring distortion, source of systematic errors that can influence the final 3D measurements. The paper provides a brief introduction of underwater optical phenomena involved in underwater photography, then presents the main differences between flat and dome ports to finally discuss the effect of manufacturing on 3D measurements in two case studies.

Media milling process optimization for manufacture of drug nanoparticles using design of experiments (DOE).

PubMed

Nekkanti, Vijaykumar; Marwah, Ashwani; Pillai, Raviraj

2015-01-01

Design of experiments (DOE), a component of Quality by Design (QbD), is systematic and simultaneous evaluation of process variables to develop a product with predetermined quality attributes. This article presents a case study to understand the effects of process variables in a bead milling process used for manufacture of drug nanoparticles. Experiments were designed and results were computed according to a 3-factor, 3-level face-centered central composite design (CCD). The factors investigated were motor speed, pump speed and bead volume. Responses analyzed for evaluating these effects and interactions were milling time, particle size and process yield. Process validation batches were executed using the optimum process conditions obtained from software Design-Expert® to evaluate both the repeatability and reproducibility of bead milling technique. Milling time was optimized to <5 h to obtain the desired particle size (d90 < 400 nm). The desirability function used to optimize the response variables and observed responses were in agreement with experimental values. These results demonstrated the reliability of selected model for manufacture of drug nanoparticles with predictable quality attributes. The optimization of bead milling process variables by applying DOE resulted in considerable decrease in milling time to achieve the desired particle size. The study indicates the applicability of DOE approach to optimize critical process parameters in the manufacture of drug nanoparticles.

[Interchangeability of biological drugs: considerations about the approval of biogeneric formulations in Chile].

PubMed

Saavedra S, Iván; Quiñones S, Luis

2006-12-01

Once drug patents expire, the health authorities can approve the registry of similar products. They must request to the manufacturer, the bibliographic background of the original product and the analytical results that certify drug quality. An inspection of the premises of the manufacturer is also required. The main goal of this approval is to decrease cost, considering that the original product is usually more expensive. This is a current situation due to the imminent expiration of the patents of many biopharmaceutical products. Therefore, in Chile, the Public Health (ISP) and the Ministry of Health should consider that for this kind of products, until now, there are no interchangeable generic drugs, and that the similar drugs that are offered have a different chemical composition, since they have been manufactured through different processes. In the case of biological drugs (e.g. erythropoietir, somatotropin, heparin) the quality and homogeneity depend from the manufacture process. Its complete composition can not be absolutely elucidated; therefore small impurities or conformational variants can elicit an altered immune response or unexpected adverse reactions. This indicates that the approval of a biogeneric drug requires in addition to pharmacokinetic studies, preclinical and clinical analytical studies such as physicochemical assays, biological and immunological test. This issues have been established by WHO and have been incorporated for the main drug registry entities all over the world (FDA, EMEA, ANVISA) to approve biogeneric products.

Opportunities for development of local forest markets: the case of Amish furniture manufacturing

Treesearch

Matt Bumgardner; Gary Graham; Charles Goebel

2012-01-01

A dramatic decline in the production of hardwood furniture in the United States has had profound impacts on employment and hardwood markets. Against this backdrop, the Amish-based furniture manufacturing cluster in Ohio has expanded and hardwood lumber consumption by the cluster is significant. Recent research suggests that 71 percent of firms in the cluster expanded...

[The requirements of standard and conditions of interchangeability of medical articles].

PubMed

Men'shikov, V V; Lukicheva, T I

2013-11-01

The article deals with possibility to apply specific approaches under evaluation of interchangeability of medical articles for laboratory analysis. The development of standardized analytical technologies of laboratory medicine and formulation of requirements of standards addressed to manufacturers of medical articles the clinically validated requirements are to be followed. These requirements include sensitivity and specificity of techniques, accuracy and precision of research results, stability of reagents' quality in particular conditions of their transportation and storage. The validity of requirements formulated in standards and addressed to manufacturers of medical articles can be proved using reference system, which includes master forms and standard samples, reference techniques and reference laboratories. This approach is supported by data of evaluation of testing systems for measurement of level of thyrotrophic hormone, thyroid hormones and glycated hemoglobin HB A1c. The versions of testing systems can be considered as interchangeable only in case of results corresponding to the results of reference technique and comparable with them. In case of absence of functioning reference system the possibilities of the Joined committee of traceability in laboratory medicine make it possible for manufacturers of reagent sets to apply the certified reference materials under development of manufacturing of sets for large listing of analytes.

Achieving continuous manufacturing for final dosage formation: challenges and how to meet them. May 20-21, 2014 Continuous Manufacturing Symposium.

PubMed

Byrn, Stephen; Futran, Maricio; Thomas, Hayden; Jayjock, Eric; Maron, Nicola; Meyer, Robert F; Myerson, Allan S; Thien, Michael P; Trout, Bernhardt L

2015-03-01

We describe the key issues and possibilities for continuous final dosage formation, otherwise known as downstream processing or drug product manufacturing. A distinction is made between heterogeneous processing and homogeneous processing, the latter of which is expected to add more value to continuous manufacturing. We also give the key motivations for moving to continuous manufacturing, some of the exciting new technologies, and the barriers to implementation of continuous manufacturing. Continuous processing of heterogeneous blends is the natural first step in converting existing batch processes to continuous. In heterogeneous processing, there are discrete particles that can segregate, versus in homogeneous processing, components are blended and homogenized such that they do not segregate. Heterogeneous processing can incorporate technologies that are closer to existing technologies, where homogeneous processing necessitates the development and incorporation of new technologies. Homogeneous processing has the greatest potential for reaping the full rewards of continuous manufacturing, but it takes long-term vision and a more significant change in process development than heterogeneous processing. Heterogeneous processing has the detriment that, as the technologies are adopted rather than developed, there is a strong tendency to incorporate correction steps, what we call below "The Rube Goldberg Problem." Thus, although heterogeneous processing will likely play a major role in the near-term transformation of heterogeneous to continuous processing, it is expected that homogeneous processing is the next step that will follow. Specific action items for industry leaders are: Form precompetitive partnerships, including industry (pharmaceutical companies and equipment manufacturers), government, and universities. These precompetitive partnerships would develop case studies of continuous manufacturing and ideally perform joint-technology development, including development of small-scale equipment and processes. Develop ways to invest internally in continuous manufacturing. How best to do this will depend on the specifics of a given organization, in particular the current development projects. Upper managers will need to energize their process developers to incorporate continuous manufacturing in at least part of their processes to gain experience and demonstrate directly the benefits. Training of continuous manufacturing technologies, organizational approaches, and regulatory approaches is a key area that industrial leaders should pursue together. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

a Case Study: Exploring Industrial Agglomeration of Manufacturing Industries in Shanghai Using Duranton and Overman's K-Density Function

NASA Astrophysics Data System (ADS)

Tian, S.; Wang, J.; Gui, Z.; Wu, H.; Wang, Y.

2017-09-01

There has wide academic and policy attention on the issue of scale economy and industrial agglomeration, with most of the attention paid to industrial geography concentration. This paper adopted a scale-independent and distance-based measurement method, K-density function or known as Duranton and Overman (DO) index, to study the manufacturing industries localization in Shanghai, which is the most representative economic development zone in China and East Asia. The result indicates the industry has a growing tendency of localization, and various spatial distribution patterns in different distances. Furthermore, the class of industry also show significant influence on the concentration pattern. Besides, the method has been coded and published on GeoCommerce, a visualization and analysis portal for industrial big data, to provide geoprocessing and spatial decision support.

76 FR 2088 - Notice of Intent To Grant Exclusive Patent License; IRFlex Corporation

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-12

... No. 78,344.//U.S. Patent No. 6,928,227: Amplification with Chalcogenide Glass Fiber, Navy Case No. 82...,797: Manufacturing Process for Chalcogenide Glasses, Navy Case No. 96,838.// U.S. Patent Application...

Magnesium in North America: A Changing Landscape

NASA Astrophysics Data System (ADS)

Slade, Susan

The changing landscape of North American manufacturing in the context of global competition is impacting the market of all raw materials, including magnesium. Current automotive fuel economy legislation and pending legislation on the emissions of greenhouse gases are impacting magnesium's largest consuming industries, such as aluminum, automotive components, steel and transition metals. These industries are all considering innovative ways to efficiently incorporate the needed raw materials into their processes. The North American magnesium market differs from other regions based on maturity, supply streams, changing manufacturing capabilities and trade cases, combined with the transformation of North American manufacturing.

Managing Risk Aversion for Low-Carbon Supply Chains with Emission Abatement Outsourcing.

PubMed

Wang, Qinpeng; He, Longfei

2018-02-21

Reducing carbon emissions, including emission abatement outsourcing at the supply-chain level, is becoming a significant but challenging problem in practice. Confronting this challenge, we therefore break down the practice to focus on a low-carbon supply chain consisting of one supplier, one manufacturer and one third-party emission-reducing contractor. The contractor offers a carbon reduction service to the manufacturer. In view of the increasing proportion of Greenhouse Gases (GHG) emissions and absence of carbon reduction policies in developing countries, we adopt the prospect of consumers' low-carbon preferences to capture the demand sensitivity on carbon emission. By exploiting the Mean-Variance (MV) model, we develop a supply chain game model considering risk aversion. Comparing the supply chain performances of the cases under risk neutrality and risk aversion, we investigate the impact of the risk aversion of the supplier and the manufacturer on the low-carbon supply chain performances, respectively. We show that the risk aversion of chain members will not influence the relationship underlain by the profit-sharing contract between the manufacturer and contractor, whereas they may extend the supplier's concerning range. Although the manufacturer's risk aversion has a positive impact on the wholesale price, interestingly, the supplier's impact on the wholesale price is negative. Furthermore, we propose a contract to coordinate the risk-averse low-carbon supply chain by tuning the aversion levels of the supplier and the manufacturer, respectively. Through numerical study, we draw on managerial insights for industrial practitioners to adopt a low carbon strategy potentially by managing the risk attitudes along the supply chain channel.

The Clinical Test of Nano gold Cosmetic for Recovering Skin Damage Due to Chemicals: Special Case

NASA Astrophysics Data System (ADS)

Taufikurohmah, T.; Wardana, A. P.; Tjahjani, S.; Sanjaya, I. G. M.; Baktir, A.; Syahrani, A.

2018-01-01

Manufacturing of Nano gold cosmetics was done at PT. Gizi Indonesia. Clinical trials to cosmetics data supported that cosmetics are able to treat skin health which has been reported partially. For special cases, the recovery process of facial skin damage should also receive attention including cases of facial skin damage caused by chemicals such as phenol, HCl, aqua regia or other harsh chemicals. The problem determined whether the Nano gold is able to recover skin damage due to the harsh chemicals. This clinical trial data on the forms of early skin damage caused by phenol was delivered in the forms of facial photos patients. The recovery progress of facial skin condition was obtained every week for two months. The data included the forms of widespread wounds during the recovery process. This statement supported by anova statistical analysis of the widespread wound changing every week for 8 times. The conclusion is skin damage due to Phenol impregnation can be recovered with the use of Nano gold cosmetics for 8 weeks. This results support the manufacturing of Nano gold cosmetics for the needs of society. It also suggest that Nano gold material can be used for medicine manufacturing in the future.

SEMATECH, A Case Study: Analysis of a Government-Industry Partnership

DTIC Science & Technology

1993-09-23

profit potential in the private market. Often, public sector technologies do not. Commercial technologies must be technically and economically...and Private Spending .................. 80 ix I. INTRODUCTION AND BACKGROUND Critics proclaim the Semiconductor Manufacturing Technology Initiative...in the R&D market and in the product market." (Katz and Ordover, 1990, p. 150) Technological spillovers result primarily from private R&D investment

Partnerships for Effective Training to Work Transitions: A Case Study of the Skillman Alliance

ERIC Educational Resources Information Center

Crisonà, Giovanni

2017-01-01

Europe hosts a significant number of global organizations in the transport market, the largest industrial R&D investor in the EU [European Union]. The market contains a significant number of jobs, and thus, there is a need for learning solutions in its domain. One of the pillars for its expansion is advanced manufacturing technology. The EU…

Vocational Education and Training in Tanzania and Zimbabwe in the Context of Economic Reform. Education Research Paper.

ERIC Educational Resources Information Center

Bennell, Paul; Bendera, Shane; Kanyenze, Godfrey; Kimambo, Emrode; Kiwia, Sixtus; Mbiriyakura, Tichafa; Mukyanuzi, Faustin; Munetsi, N.; Muzulu, Jo; Parsalaw, Willy; Temu, John

Developments in vocational education and training (VET) in Tanzania and Zimbabwe since the 1980s were examined in the context of economic reform. Formal VET provision in each country's public and private sectors was reviewed, and case studies of one firm in each country's manufacturing and tourism industries were conducted. The research identified…

Application of PBL in the Course Fluid and Electrical Drive Systems, Case Study: Manufacturing an Automated Punch Machine

ERIC Educational Resources Information Center

Sedaghat, Ahmad; AlJundub, Mohammad; Eilaghi, Armin; Bani-Hani, Ehab; Sabri, Farhad; Mbarki, Raouf; Assad, M. El Haj

2017-01-01

The PBL unit of fluid and electrical drive systems is taught in final semester of undergraduates in mechanical engineering department of the Australian College of Kuwait (ACK). The recent project on an automated punching machine is discovered more appealing to both students and instructors in triggering new ideas and satisfaction end results. In…

An Examination of the Dynamics of Organizational Culture and Values-Based Leader Identities and Behaviors: One Company's Experience

ERIC Educational Resources Information Center

MacTavish, Murray D.; Kolb, Judith A.

2008-01-01

This in-depth case study utilized grounded theory methodology to discover how a large privately-owned manufacturing firm in Northeastern USA develops values-based leaders, particularly from minority populations. Over 18 months, interviews with 35 leaders from five levels explored the perceived influence of the environment on leaders' behaviors and…

Training for the Future? A Case Study of Emerging Education, Training and Development Practitioners in the South African Clothing Manufacturing Industry

ERIC Educational Resources Information Center

Jones, Barbara; Cooper, Linda; McMillan, Janice

2006-01-01

This article investigates how training instructors in the South African clothing industry were prepared for their roles as Education, Training and Development Practitioners (ETDPs) by a university adult education programme. The key focus is on how these emerging ETDPs experienced their changing roles, identities and approaches to teaching and the…

"Arubaito," or Short-Term Working Abroad in Japan: A Case Study of Brazilian University Students of Japanese Descent

ERIC Educational Resources Information Center

Sasaki, Lindsey

2012-01-01

International migration between Japan and Brazil dates back to 1908, when the first group of Japanese migrated to Brazil. However, in the 1980s, a reverse flow occurred, as thousands of Brazilians of Japanese descent traveled to Japan to work in manufacturing and construction factories ("dekasegi" workers). Japanese Brazilians up until…

Styling and Design in Multi-Segmented Market Strategies: The Case of the Italian Knitwear Sector

ERIC Educational Resources Information Center

Marcone, Maria Rosaria

2013-01-01

This study analyses Italian knitwear manufacturers that operate both in international consumer and in business markets and assesses the different forms of competition that exist between them. The purpose of the research is to analyse the different positioning of these firms within the chain of production that they belong to. The firms that deal…

Jobs to Manufacturing Careers: Work-Based Courses. Work-Based Learning in Action

ERIC Educational Resources Information Center

Kobes, Deborah

2016-01-01

This case study, one of a series of publications exploring effective and inclusive models of work-based learning, finds that work-based courses bring college to the production line by using the job as a learning lab. Work-based courses are an innovative way to give incumbent workers access to community college credits and degrees. They are…

Computer integration of engineering design and production: A national opportunity

NASA Astrophysics Data System (ADS)

1984-10-01

The National Aeronautics and Space Administration (NASA), as a purchaser of a variety of manufactured products, including complex space vehicles and systems, clearly has a stake in the advantages of computer-integrated manufacturing (CIM). Two major NASA objectives are to launch a Manned Space Station by 1992 with a budget of $8 billion, and to be a leader in the development and application of productivity-enhancing technology. At the request of NASA, a National Research Council committee visited five companies that have been leaders in using CIM. Based on these case studies, technical, organizational, and financial issues that influence computer integration are described, guidelines for its implementation in industry are offered, and the use of CIM to manage the space station program is recommended.

Computer integration of engineering design and production: A national opportunity

NASA Technical Reports Server (NTRS)

1984-01-01

The National Aeronautics and Space Administration (NASA), as a purchaser of a variety of manufactured products, including complex space vehicles and systems, clearly has a stake in the advantages of computer-integrated manufacturing (CIM). Two major NASA objectives are to launch a Manned Space Station by 1992 with a budget of $8 billion, and to be a leader in the development and application of productivity-enhancing technology. At the request of NASA, a National Research Council committee visited five companies that have been leaders in using CIM. Based on these case studies, technical, organizational, and financial issues that influence computer integration are described, guidelines for its implementation in industry are offered, and the use of CIM to manage the space station program is recommended.

Additive Manufacturing Techniques for the Reconstruction of 3D Fetal Faces

PubMed Central

Citro, Daniela; Padula, Francesco; Motyl, Barbara; Marcolin, Federica; Calì, Michele

2017-01-01

This paper deals with additive manufacturing techniques for the creation of 3D fetal face models starting from routine 3D ultrasound data. In particular, two distinct themes are addressed. First, a method for processing and building 3D models based on the use of medical image processing techniques is proposed. Second, the preliminary results of a questionnaire distributed to future parents consider the use of these reconstructions both from an emotional and an affective point of view. In particular, the study focuses on the enhancement of the perception of maternity or paternity and the improvement in the relationship between parents and physicians in case of fetal malformations, in particular facial or cleft lip diseases. PMID:29410600

Investigation of dimensional variation in parts manufactured by fused deposition modeling using Gauge Repeatability and Reproducibility

NASA Astrophysics Data System (ADS)

Mohamed, Omar Ahmed; Hasan Masood, Syed; Lal Bhowmik, Jahar

2018-02-01

In the additive manufacturing (AM) market, the question is raised by industry and AM users on how reproducible and repeatable the fused deposition modeling (FDM) process is in providing good dimensional accuracy. This paper aims to investigate and evaluate the repeatability and reproducibility of the FDM process through a systematic approach to answer this frequently asked question. A case study based on the statistical gage repeatability and reproducibility (gage R&R) technique is proposed to investigate the dimensional variations in the printed parts of the FDM process. After running the simulation and analysis of the data, the FDM process capability is evaluated, which would help the industry for better understanding the performance of FDM technology.

Rituximab for the treatment of relapsed/refractory chronic lymphocytic leukaemia.

PubMed

Dretzke, J; Barton, P; Kaambwa, B; Connock, M; Uthman, O; Bayliss, S; Meads, C

2010-10-01

This paper presents a summary of the evidence review group (ERG) report on the clinical effectiveness and cost-effectiveness of rituximab with chemotherapy compared to chemotherapy only for the treatment of relapsed/refractory chronic lymphocytic leukaemia (CLL) based on the manufacturer's submission to the National Institute for Health and Clinical Excellence (NICE) as part of the single technology appraisal (STA) process. Evidence was available in the form of one open-label, ongoing, unpublished randomised controlled trial (RCT), REACH (Rituximab in the Study of Relapsed Chronic Lymphocytic Leukemia), conducted by the manufacturer, which compared rituximab with a fludarabine and cyclophosphamide combination (R-FC) to fludarabine and cyclophosphamide (FC) only. REACH was scheduled to run for 8 years; however, the data provided were immature, with a median observation time at the time of data analysis of 2.1 years. REACH provided evidence of prolonged progression free survival with R-FC compared to FC (10 months, investigators' data), but no evidence of an overall survival benefit with R-FC. Patients refractory to fludarabine and with prior rituximab exposure were excluded from REACH and no controlled studies were identified by the ERG for these patient groups. The ERG had concerns about the structure of the economic model submitted by the manufacturer, which did not allow improvement in quality of life from treatment while in a progressed state. The manufacturer's model further assumed a divergence in cumulative deaths between the R-FC and FC treatment arms from the outset, which did not accord with observed data from REACH. When the survival advantage was removed, the manufacturer's base-case incremental cost-effectiveness ratio (ICER) changed from 15,593 pounds to between 40,000 pounds and 42,000 pounds per quality-adjusted life-year (QALY). With no survival advantage, the ICER became sensitive to changes in utility. There was no good empirical evidence on the utility of CLL patients in different states. Allowing for the possibility of a survival advantage with rituximab (although not supported by current evidence), the ERG performed further modelling, which found that rituximab would be cost-effective at 20,000 pounds/QALY (30,000 pounds/QALY) if a reduction in survival advantage relative to the manufacturer's base case of 40% (80%) was assumed. The guidance issued by NICE in July 2010 as a result of the STA recommends rituximab with FC for people with relapsed or refractory chronic lymphocytic leukaemia, except when the condition is refractory to fludarabine or where there has been previous treatment with rituximab.

[Anaphylaxis related to measles, mumps, and rubella vaccine in Santa Catarina State, Brazil, 2014 and 2015].

PubMed

Fantinato, Francieli Fontana Sutile Tardetti; Vargas, Alexander; Carvalho, Sandra Maria Deotti; Domingues, Carla Magda Allan Santos; Barreto, Gisele; Fialho, Arieli Schiessl; Silva, Roselita Heinen da; Saad, Eduardo; Agredo, Ivonne Natalia Solarte

2018-03-12

The study aimed to describe cases and verify the frequency of anaphylaxis related to measles, mumps, and rubella (MMR) vaccine produced by manufacturer A and to assess associated risk factors. This was a case-control study (1:4) in Santa Catarina State, Brazil, from July 14, 2014, to January 12, 2015, in children from one year to less than five years of age, vaccinated with MMR and reported with anaphylaxis, while the controls were without anaphylaxis. The measure of association was odds ratio (OR) with 95% confidence interval (95%CI), using the chi-square and Fisher's exact tests. Anaphylaxis rates were calculated per doses distributed/administered. Fifteen cases and 60 controls were interviewed in 12 municipalities (counties). Anaphylaxis rates were 2.46 and 5.05 cases per 100,000 doses distributed and administered, respectively. Among the cases of anaphylaxis, eight (53.4%) were males, and among the controls, 36 (60%), with p = 0.64. The bivariate analysis of anaphylaxis and cow's milk protein allergy (CMPA) showed OR = 51.62, with p = 0.00002 and 95%CI: 5.59-476.11. The variables family food allergy, breastfeeding, previous post-vaccine adverse event (PVAE), and simultaneous vaccination were not statistically significant (p = 0.48; p = 1.00; p = 0.49; p = 0.61). Anaphylaxis rates per doses distributed/administered exceeded 1/100,000 doses administered (expected rate). Anaphylaxis and CMPA showed a statistically significant association. No statistically significant associations were found with simultaneous vaccination, breastfeeding, family food allergy, or history of PVAE. the manufacturer should specify the product's components in the package insert, and children with a history of CMPA should not be vaccinated with this vaccine.

'You've got m@il: fluoxetine coming soon!': accessibility and quality of a prescription drug sold on the web.

PubMed

Gelatti, U; Pedrazzani, R; Marcantoni, C; Mascaretti, S; Repice, C; Filippucci, L; Zerbini, I; Dal Grande, M; Orizio, G; Feretti, D

2013-09-01

The increasing phenomenon of online pharmacies has potential for serious public health problems. This study aimed to evaluate the possibility of accessing a prescription drug in the absence of a prescription for an Italian purchaser. Fluoxetine pills were ordered from several online pharmacies. The study included website analysis, and the quality of the received product including packaging, chemical and microbiological analyses. Orders could be placed correctly on 61 of the 98 selected websites, and a sales transaction was concluded successfully on 17 websites. Thirteen drug samples were eventually received. In one case it was necessary to fill in a questionnaire before ordering the drugs. All websites displayed aggressive marketing strategies. There was wide variation in terms of domain registration, company base (when declared) and manufacturer's location (mostly India). All pills were delivered in sealed blister packs showing the lot number and manufacturer's details. A leaflet was enclosed in one case only. In three cases we received more pills than ordered, and in one case Viagra pills as a free gift. Pharmacopoeia microbiological requirements were satisfied. Chemical analysis revealed that the active principle was always present, although many samples did not meet the Pharmacopoeia "other impurities" or "total impurities" criteria. Heavy metals and solvents regulated by the Pharmacopoeia did not exceed the set limits; some of the non-regulated ones were also assessed, in some cases with a positive result (e.g. styrene). About 20% of purchase attempts resulted in delivery of the drugs, even in the absence of a medical prescription. Traceability was poor and drug quality was generally worse compared to conventional pharmacy-purchased products. Based on all these broad-spectrum results, user safety appears not to be globally guaranteed. Copyright © 2013 Elsevier B.V. All rights reserved.

Quantification of human epidermal growth factor receptor 2 immunohistochemistry using the Ventana Image Analysis System: correlation with gene amplification by fluorescence in situ hybridization: the importance of instrument validation for achieving high (>95%) concordance rate.

PubMed

Dennis, Jake; Parsa, Rezvaneh; Chau, Donnie; Koduru, Prasad; Peng, Yan; Fang, Yisheng; Sarode, Venetia Rumnong

2015-05-01

The use of computer-based image analysis for scoring human epidermal growth factor receptor 2 (HER2) immunohistochemistry (IHC) has gained a lot of interest recently. We investigated the performance of the Ventana Image Analysis System (VIAS) in HER2 quantification by IHC and its correlation with fluorescence in situ hybridization (FISH). We specifically compared the 3+ IHC results using the manufacturer's machine score cutoffs versus laboratory-defined cutoffs with the FISH assay. Using the manufacturer's 3+ cutoff (VIAS score; 2.51 to 3.5), 181/536 (33.7%) were scored 3+, and FISH was positive in 147/181 (81.2%), 2 (1.1%) were equivocal, and 32 (17.6%) were FISH (-). Using the laboratory-defined 3+ cutoff (VIAS score 3.5), 52 (28.7%) cases were downgraded to 2+, of which 29 (55.7%) were FISH (-), and 23 (44.2%) were FISH (+). With the revised cutoff, there were improvements in the concordance rate from 89.1% to 97.0% and in the positive predictive value from 82.1% to 97.6%. The false-positive rate for 3+ decreased from 9.0% to 0.8%. Six of 175 (3.4%) IHC (-) cases were FISH (+). Three cases with a VIAS score 3.5 showed polysomy of chromosome 17. In conclusion, the VIAS may be a valuable tool for assisting pathologists in HER2 scoring; however, the positive cutoff defined by the manufacturer is associated with a high false-positive rate. This study highlights the importance of instrument validation/calibration to reduce false-positive results.

A national outbreak of Salmonella enteritidis infections from ice cream. The Investigation Team.

PubMed

Hennessy, T W; Hedberg, C W; Slutsker, L; White, K E; Besser-Wiek, J M; Moen, M E; Feldman, J; Coleman, W W; Edmonson, L M; MacDonald, K L; Osterholm, M T

1996-05-16

In September 1994, the Minnesota Department of Health detected an increase in the number of reports of Salmonella enteritidis infections. After a case-control study implicated a nationally distributed brand of ice cream (Schwan's) in the outbreak, the product was recalled and further epidemiologic and microbiologic investigations were conducted. We defined an outbreak-associated case of S. enteritidis infection as one in which S. enteritidis was cultured from a person who became ill in September or October 1994. We established national surveillance and surveyed customers of the implicated manufacturer. The steps involved in the manufacture of ice cream associated with cases of S. enteritidis infection were compared with those of products not known to be associated with infection matched for the date of manufacture. Cultures for bacteria were obtained from ice cream samples, the ice cream plant, and tanker trailers that had transported the ice cream base (premix) to the plant. We estimate that S. enteritidis gastroenteritis developed in 224,000 persons in the United States after they ate Schwan's ice cream. The attack rate for consumers was 6.6 percent. Ice cream associated with infection contained a higher percentage of premix that had been transported by tanker that had carried nonpasteurized eggs immediately before (P = 0.02). S. enteritidis was isolated from 8 of 226 ice cream products (3 percent), but not from environmental samples obtained from the ice cream plant (n = 157) or tanker trailers (n = 204). This nationwide outbreak of salmonellosis was most likely the result of contamination of pasteurized ice cream premix during transport in tanker trailers that had previously carried nonpasteurized liquid eggs containing S. enteritidis. To prevent further outbreaks, food products not destined for repasteurization should be transported in dedicated containers.

Typhoid fever outbreak associated with frozen mamey pulp imported from Guatemala to the western United States, 2010.

PubMed

Loharikar, Anagha; Newton, Anna; Rowley, Patricia; Wheeler, Charlotte; Bruno, Tami; Barillas, Haroldo; Pruckler, James; Theobald, Lisa; Lance, Susan; Brown, Jeffrey M; Barzilay, Ezra J; Arvelo, Wences; Mintz, Eric; Fagan, Ryan

2012-07-01

Fifty-four outbreaks of domestically acquired typhoid fever were reported between 1960 and 1999. In 2010, the Southern Nevada Health District detected an outbreak of typhoid fever among persons who had not recently travelled abroad. We conducted a case-control study to examine the relationship between illness and exposures. A case was defined as illness with the outbreak strain of Salmonella serotype Typhi, as determined by pulsed-field gel electrophoresis (PFGE), with onset during 2010. Controls were matched by neighborhood, age, and sex. Bivariate and multivariate statistical analyses were completed using logistic regression. Traceback investigation was completed. We identified 12 cases in 3 states with onset from 15 April 2010 to 4 September 2010. The median age of case patients was 18 years (range, 4-48 years), 8 (67%) were female, and 11 (92%) were Hispanic. Nine (82%) were hospitalized; none died. Consumption of frozen mamey pulp in a fruit shake was reported by 6 of 8 case patients (75%) and none of the 33 controls (matched odds ratio, 33.9; 95% confidence interval, 4.9). Traceback investigations implicated 2 brands of frozen mamey pulp from a single manufacturer in Guatemala, which was also implicated in a 1998-1999 outbreak of typhoid fever in Florida. Reporting of individual cases of typhoid fever and subtyping of isolates by PFGE resulted in rapid detection of an outbreak associated with a ready-to-eat frozen food imported from a typhoid-endemic region. Improvements in food manufacturing practices and monitoring will prevent additional outbreaks.

Study Of Pre-Shaped Membrane Mirrors And Electrostatic Mirrors With Nonlinear-Optical Correction

DTIC Science & Technology

2002-01-01

mirrors have been manufactured of glass-like material Zerodur with very low coefficient of linear expansion. They have a more light cellular construction...primary and flat secondary mirrors are both segmented ones. In the case of the primary mirror made of traditional materials such as Zerodur or fused...FINAL REPORT ISTC Project #2103p “Study of Pre-Shaped Membrane Mirrors and Electrostatic Mirrors with Nonlinear-Optical Correction” Manager

A case-control study of malignant and non-malignant respiratory disease among employees of a fiberglass manufacturing facility.

PubMed Central

Chiazze, L; Watkins, D K; Fryar, C

1992-01-01

A case-control study was conducted to determine the influence of non-workplace factors on risk of respiratory disease among workers at the Owens-Corning Fiberglas plant in Newark, Ohio. Cases and controls were drawn from a historical cohort mortality study conducted on behalf of the Thermal Insulation Manufacturers Association (TIMA) of workers employed at Newark for at least one year between 1 January 1940 and 31 December 1963 and followed up to the end of 1982. The TIMA study reported a statistically significant increase in respiratory cancer (compared with national death rates). Interviews were completed for 144 lung cancer cases and 299 matching controls and 102 non-malignant respiratory disease cases and 201 matching controls. Unadjusted odds ratios (ORs) were used to assess the association between lung cancer or non-malignant respiratory disease and birthplace, education, income, marital state, smoking with a duration of six months or more, age at which smoking first started, and duration of smoking. Only the smoking variables were statistically significant. For lung cancer, of the variables entered into a conditional logistic regression model, only the smoking OR of 23.4 (95% CI 3.2-172.9) was statistically significant. For non-malignant respiratory disease no variables entered into the final model were statistically significant. Results of the interview portion of our case-control study clearly indicate that smoking is the most important non-workplace factor for risk of lung cancer in this group of workers. Smoking does not seem to play as important a part, however, for non-malignant respiratory disease. Prevalence of cigarette smoking at the Newark plant was estimated for birth cohorts by calendar year. Corresponding data for the United States were compiled from national smoking surveys. Prevalence of cigarette smoking for Newark in 1955 appears to be sufficiently greater than the corresponding United States data in 1955 to suggest that some of the previously reported excess of lung cancer for Newark based on United States mortality may be accounted for by differences in the prevalence of cigarette smoking between white men in Newark and those in the United States as a whole. PMID:1599870

International Trade: Rules of Origin

DTIC Science & Technology

2009-03-06

products has been subcontracted to a global manufacturing company that operates in many countries. While some major retailers and brand -name distributors...often the case in today’s global trading environment—determining origin can be a very complex, sometimes subjective, and time-consuming process. U.S...CBP origin determinations, and the effects of the global manufacturing process on ROO. Third, we conclude with some alternatives and options that

International Trade: Rules of Origin

DTIC Science & Technology

2008-08-22

2007). and the Gap) and brand -name distributors of consumer products (such as Mattel, Nike , and Dell) utilize manufacturing companies in China and...subcontracted to a global manufacturing company that operates in many countries. While some major retailers and brand -name distributors have established...However, when a finished product’s component parts originate in many countries — as is often the case in today’s global trading environment

Damage-Tolerant Fan Casings for Jet Engines

NASA Technical Reports Server (NTRS)

2006-01-01

All turbofan engines work on the same principle. A large fan at the front of the engine draws air in. A portion of the air enters the compressor, but a greater portion passes on the outside of the engine this is called bypass air. The air that enters the compressor then passes through several stages of rotating fan blades that compress the air more, and then it passes into the combustor. In the combustor, fuel is injected into the airstream, and the fuel-air mixture is ignited. The hot gasses produced expand rapidly to the rear, and the engine reacts by moving forward. If there is a flaw in the system, such as an unexpected obstruction, the fan blade can break, spin off, and harm other engine components. Fan casings, therefore, need to be strong enough to contain errant blades and damage-tolerant to withstand the punishment of a loose blade-turned-projectile. NASA has spearheaded research into improving jet engine fan casings, ultimately discovering a cost-effective approach to manufacturing damage-tolerant fan cases that also boast significant weight reduction. In an aircraft, weight reduction translates directly into fuel burn savings, increased payload, and greater aircraft range. This technology increases safety and structural integrity; is an attractive, viable option for engine manufacturers, because of the low-cost manufacturing; and it is a practical alternative for customers, as it has the added cost saving benefits of the weight reduction.

Manufacturing Economics of Plant-Made Biologics: Case Studies in Therapeutic and Industrial Enzymes

PubMed Central

Tusé, Daniel; McDonald, Karen A.

2014-01-01

Production of recombinant biologics in plants has received considerable attention as an alternative platform to traditional microbial and animal cell culture. Industrially relevant features of plant systems include proper eukaryotic protein processing, inherent safety due to lack of adventitious agents, more facile scalability, faster production (transient systems), and potentially lower costs. Lower manufacturing cost has been widely claimed as an intuitive feature of the platform by the plant-made biologics community, even though cost information resides within a few private companies and studies accurately documenting such an advantage have been lacking. We present two technoeconomic case studies representing plant-made enzymes for diverse applications: human butyrylcholinesterase produced indoors for use as a medical countermeasure and cellulases produced in the field for the conversion of cellulosic biomass into ethanol as a fuel extender. Production economics were modeled based on results reported with the latest-generation expression technologies on Nicotiana host plants. We evaluated process unit operations and calculated bulk active and per-dose or per-unit costs using SuperPro Designer modeling software. Our analyses indicate that substantial cost advantages over alternative platforms can be achieved with plant systems, but these advantages are molecule/product-specific and depend on the relative cost-efficiencies of alternative sources of the same product. PMID:24977145

Manufacturing economics of plant-made biologics: case studies in therapeutic and industrial enzymes.

PubMed

Tusé, Daniel; Tu, Tiffany; McDonald, Karen A

2014-01-01

Production of recombinant biologics in plants has received considerable attention as an alternative platform to traditional microbial and animal cell culture. Industrially relevant features of plant systems include proper eukaryotic protein processing, inherent safety due to lack of adventitious agents, more facile scalability, faster production (transient systems), and potentially lower costs. Lower manufacturing cost has been widely claimed as an intuitive feature of the platform by the plant-made biologics community, even though cost information resides within a few private companies and studies accurately documenting such an advantage have been lacking. We present two technoeconomic case studies representing plant-made enzymes for diverse applications: human butyrylcholinesterase produced indoors for use as a medical countermeasure and cellulases produced in the field for the conversion of cellulosic biomass into ethanol as a fuel extender. Production economics were modeled based on results reported with the latest-generation expression technologies on Nicotiana host plants. We evaluated process unit operations and calculated bulk active and per-dose or per-unit costs using SuperPro Designer modeling software. Our analyses indicate that substantial cost advantages over alternative platforms can be achieved with plant systems, but these advantages are molecule/product-specific and depend on the relative cost-efficiencies of alternative sources of the same product.

National Institutes of Health-Sponsored Clinical Islet Transplantation Consortium Phase 3 Trial: Manufacture of a Complex Cellular Product at Eight Processing Facilities.

PubMed

Ricordi, Camillo; Goldstein, Julia S; Balamurugan, A N; Szot, Gregory L; Kin, Tatsuya; Liu, Chengyang; Czarniecki, Christine W; Barbaro, Barbara; Bridges, Nancy D; Cano, Jose; Clarke, William R; Eggerman, Thomas L; Hunsicker, Lawrence G; Kaufman, Dixon B; Khan, Aisha; Lafontant, David-Erick; Linetsky, Elina; Luo, Xunrong; Markmann, James F; Naji, Ali; Korsgren, Olle; Oberholzer, Jose; Turgeon, Nicole A; Brandhorst, Daniel; Chen, Xiaojuan; Friberg, Andrew S; Lei, Ji; Wang, Ling-Jia; Wilhelm, Joshua J; Willits, Jamie; Zhang, Xiaomin; Hering, Bernhard J; Posselt, Andrew M; Stock, Peter G; Shapiro, A M James; Chen, Xiaojuan

2016-11-01

Eight manufacturing facilities participating in the National Institutes of Health-sponsored Clinical Islet Transplantation (CIT) Consortium jointly developed and implemented a harmonized process for the manufacture of allogeneic purified human pancreatic islet (PHPI) product evaluated in a phase 3 trial in subjects with type 1 diabetes. Manufacturing was controlled by a common master production batch record, standard operating procedures that included acceptance criteria for deceased donor organ pancreata and critical raw materials, PHPI product specifications, certificate of analysis, and test methods. The process was compliant with Current Good Manufacturing Practices and Current Good Tissue Practices. This report describes the manufacturing process for 75 PHPI clinical lots and summarizes the results, including lot release. The results demonstrate the feasibility of implementing a harmonized process at multiple facilities for the manufacture of a complex cellular product. The quality systems and regulatory and operational strategies developed by the CIT Consortium yielded product lots that met the prespecified characteristics of safety, purity, potency, and identity and were successfully transplanted into 48 subjects. No adverse events attributable to the product and no cases of primary nonfunction were observed. © 2016 by the American Diabetes Association.

National Institutes of Health–Sponsored Clinical Islet Transplantation Consortium Phase 3 Trial: Manufacture of a Complex Cellular Product at Eight Processing Facilities

PubMed Central

Balamurugan, A.N.; Szot, Gregory L.; Kin, Tatsuya; Liu, Chengyang; Czarniecki, Christine W.; Barbaro, Barbara; Bridges, Nancy D.; Cano, Jose; Clarke, William R.; Eggerman, Thomas L.; Hunsicker, Lawrence G.; Kaufman, Dixon B.; Khan, Aisha; Lafontant, David-Erick; Linetsky, Elina; Luo, Xunrong; Markmann, James F.; Naji, Ali; Korsgren, Olle; Oberholzer, Jose; Turgeon, Nicole A.; Brandhorst, Daniel; Chen, Xiaojuan; Friberg, Andrew S.; Lei, Ji; Wang, Ling-jia; Wilhelm, Joshua J.; Willits, Jamie; Zhang, Xiaomin; Hering, Bernhard J.; Posselt, Andrew M.; Stock, Peter G.; Shapiro, A.M. James

2016-01-01

Eight manufacturing facilities participating in the National Institutes of Health–sponsored Clinical Islet Transplantation (CIT) Consortium jointly developed and implemented a harmonized process for the manufacture of allogeneic purified human pancreatic islet (PHPI) product evaluated in a phase 3 trial in subjects with type 1 diabetes. Manufacturing was controlled by a common master production batch record, standard operating procedures that included acceptance criteria for deceased donor organ pancreata and critical raw materials, PHPI product specifications, certificate of analysis, and test methods. The process was compliant with Current Good Manufacturing Practices and Current Good Tissue Practices. This report describes the manufacturing process for 75 PHPI clinical lots and summarizes the results, including lot release. The results demonstrate the feasibility of implementing a harmonized process at multiple facilities for the manufacture of a complex cellular product. The quality systems and regulatory and operational strategies developed by the CIT Consortium yielded product lots that met the prespecified characteristics of safety, purity, potency, and identity and were successfully transplanted into 48 subjects. No adverse events attributable to the product and no cases of primary nonfunction were observed. PMID:27465220

Recent advances in the reconstruction of cranio-maxillofacial defects using computer-aided design/computer-aided manufacturing.

PubMed

Oh, Ji-Hyeon

2018-12-01

With the development of computer-aided design/computer-aided manufacturing (CAD/CAM) technology, it has been possible to reconstruct the cranio-maxillofacial defect with more accurate preoperative planning, precise patient-specific implants (PSIs), and shorter operation times. The manufacturing processes include subtractive manufacturing and additive manufacturing and should be selected in consideration of the material type, available technology, post-processing, accuracy, lead time, properties, and surface quality. Materials such as titanium, polyethylene, polyetheretherketone (PEEK), hydroxyapatite (HA), poly-DL-lactic acid (PDLLA), polylactide-co-glycolide acid (PLGA), and calcium phosphate are used. Design methods for the reconstruction of cranio-maxillofacial defects include the use of a pre-operative model printed with pre-operative data, printing a cutting guide or template after virtual surgery, a model after virtual surgery printed with reconstructed data using a mirror image, and manufacturing PSIs by directly obtaining PSI data after reconstruction using a mirror image. By selecting the appropriate design method, manufacturing process, and implant material according to the case, it is possible to obtain a more accurate surgical procedure, reduced operation time, the prevention of various complications that can occur using the traditional method, and predictive results compared to the traditional method.

Characterizing dense suspensions: two case studies from the pharmaceutical industry

NASA Astrophysics Data System (ADS)

Goldfarb, David J.; Khawaja, Nazia; Kazakevich, Irina; Bhattacharjee, Himanshu; Heslinga, Michael; Dalton, Chad

2015-11-01

Liquid suspensions of Active Pharmaceutical Ingredient powders are present as pharmaceutical dosage forms in the form of oral suspensions and injectables. We present two case studies, both dense (~ 30-40%) suspensions, in which the physical characterization of the product, specifically, particle size & shape and rheology were key to understanding the key product attributes as pertaining to the manufacturing process and to patient administration. For the one case study, an oral suspension, identifying variations in particle morphology during the wet milling of the product was key to the product understanding necessary to modify the milling process. Rheological measurements were applied as well. For the second case study, an injectable, results from different particle size measurement techniques and rheological measurements indicated the possibility of flocculation in a formulation. Additionally, measurements were obtained to assess the ``injectability'' of the product via rheometer and texture analyzer measurements and Poiseuille flow modeling. As a result, the relevant shear rate regime for this drug product administration was identified.

The Super Efficient Refrigerator Program: Case study of a Golden Carrot program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eckert, J B

1995-07-01

The work in this report was conducted by the Analytic Studies Division (ASD) of the National Renewable Energy Laboratory (NREL) for the U.S. Department of Energy Office of Energy Efficiency and Renewable Energy, Office of Building Technologies. This case study describes the development and implementation of the Super Efficient Refrigerator Program (SERP), which awarded $30 million to the refrigerator manufacturer that developed and commercialized a refrigerator that exceeded 1993 federal efficiency standards by at least 25%. The program was funded by 24 public and private utilities. As the first Golden Carrot program to be implemented in the United States, SERPmore » was studied as an example for future `market-pull` efforts.« less

An automation of design and modelling tasks in NX Siemens environment with original software - cost module

NASA Astrophysics Data System (ADS)

Zbiciak, R.; Grabowik, C.; Janik, W.

2015-11-01

The design-constructional process is a creation activity which strives to fulfil, as well as it possible at the certain moment of time, all demands and needs formulated by a user taking into account social, technical and technological advances. Engineer knowledge and skills and their inborn abilities have the greatest influence on the final product quality and cost. They have also deciding influence on product technical and economic value. Taking into account above it seems to be advisable to make software tools that support an engineer in the process of manufacturing cost estimation. The Cost module is built with analytical procedures which are used for relative manufacturing cost estimation. As in the case of the Generator module the Cost module was written in object programming language C# in Visual Studio environment. During the research the following eight factors, that have the greatest influence on overall manufacturing cost, were distinguished and defined: (i) a gear wheel teeth type it is straight or helicoidal, (ii) a gear wheel design shape A, B with or without wheel hub, (iii) a gear tooth module, (iv) teeth number, (v) gear rim width, (vi) gear wheel material, (vii) heat treatment or thermochemical treatment, (viii) accuracy class. Knowledge of parameters (i) to (v) is indispensable for proper modelling of 3D gear wheels models in CAD system environment. These parameters are also processed in the Cost module. The last three parameters it is (vi) to (viii) are exclusively used in the Cost module. The estimation of manufacturing relative cost is based on indexes calculated for each particular parameter. Estimated in this way the manufacturing relative cost gives an overview of design parameters influence on the final gear wheel manufacturing cost. This relative manufacturing cost takes values from 0.00 to 1,00 range. The bigger index value the higher relative manufacturing cost is. Verification whether the proposed algorithm of relative manufacturing costs estimation has been designed properly was made by comparison of the achieved from the algorithm results with those obtained from industry. This verification has indicated that in most cases both group of results are similar. Taking into account above it is possible to draw a conclusion that the Cost module might play significant role in design constructional process by adding an engineer at the selection stage of alternative gear wheels design. It should be remembered that real manufacturing cost can differ significantly according to available in a factory manufacturing techniques and stock of machine tools.

Case Study: Microbial Ecology and Forensics of Chinese Drywall-Elemental Sulfur Disproportionation as Primary Generator of Hydrogen Sulfide.

PubMed

Tomei Torres, Francisco A

2017-06-21

Drywall manufactured in China released foul odors attributed to volatile sulfur compounds. These included hydrogen sulfide, methyl mercaptan, and sulfur dioxide. Given that calcium sulfate is the main component of drywall, one would suspect bacterial reduction of sulfate to sulfide as the primary culprit. However, when the forensics, i.e., the microbial and chemical signatures left in the drywall, are studied, the evidence suggests that, rather than dissimilatory sulfate reduction, disproportionation of elemental sulfur to hydrogen sulfide and sulfate was actually the primary cause of the malodors. Forensic evidence suggests that the transformation of elemental sulfur went through several abiological and microbial stages: (1) partial volatilization of elemental sulfur during the manufacture of plaster of Paris, (2) partial abiotic disproportionation of elemental sulfur to sulfide and thiosulfate during the manufacture of drywall, (3) microbial disproportionation of elemental sulfur to sulfide and sulfate resulting in neutralization of all alkalinity, and acidification below pH 4, (4) acidophilic microbial disproportionation of elemental sulfur to sulfide and sulfuric acid, and (5) hydrogen sulfide volatilization, coating of copper fixtures resulting in corrosion, and oxidation to sulfur dioxide.

Long-term lumen depreciation behavior and failure modes of multi-die array LEDs

NASA Astrophysics Data System (ADS)

Jayawardena, Asiri; Marcus, Daniel; Prugue, Ximena; Narendran, Nadarajah

2013-09-01

One of the main advantages of multi-die array light-emitting diodes (LEDs) is their high flux density. However, a challenge for using such a product in lighting fixture applications is the heat density and the need for thermal management to keep the junction temperatures of all the dies low for long-term reliable performance. Ten multi-die LED array samples for each product from four different manufacturers were subjected to lumen maintenance testing (as described in IES-LM-80-08), and their resulting lumen depreciation and failure modes were studied. The products were tested at the maximum case (or pin) temperature reported by the respective manufacturer by appropriately powering the LEDs. In addition, three samples for each product from two different manufacturers were subjected to rapid thermal cycling, and the resulting lumen depreciation and failure modes were studied. The results showed that the exponential lumen decay model using long-term lumen maintenance data as recommended in IES TM-21 does not fit for all package types. The failure of a string of dies and single die failure in a string were observed in some of the packages.

Carbon Capture and Utilization in the Industrial Sector.

PubMed

Psarras, Peter C; Comello, Stephen; Bains, Praveen; Charoensawadpong, Panunya; Reichelstein, Stefan; Wilcox, Jennifer

2017-10-03

The fabrication and manufacturing processes of industrial commodities such as iron, glass, and cement are carbon-intensive, accounting for 23% of global CO 2 emissions. As a climate mitigation strategy, CO 2 capture from flue gases of industrial processes-much like that of the power sector-has not experienced wide adoption given its high associated costs. However, some industrial processes with relatively high CO 2 flue concentration may be viable candidates to cost-competitively supply CO 2 for utilization purposes (e.g., polymer manufacturing, etc.). This work develops a methodology that determines the levelized cost ($/tCO 2 ) of separating, compressing, and transporting carbon dioxide. A top-down model determines the cost of separating and compressing CO 2 across 18 industrial processes. Further, the study calculates the cost of transporting CO 2 via pipeline and tanker truck to appropriately paired sinks using a bottom-up cost model and geo-referencing approach. The results show that truck transportation is generally the low-cost alternative given the relatively small volumes (ca. 100 kt CO 2 /a). We apply our methodology to a regional case study in Pennsylvania, which shows steel and cement manufacturing paired to suitable sinks as having the lowest levelized cost of capture, compression, and transportation.

A Digital Approach to Improved Overdentures for the Adolescent Oligodontia Patient.

PubMed

Cooper, Lyndon F; Culp, Lee; Luedin, Nicole

2016-05-01

The use of overdentures for treatment of oligodontia in adolescent patients using conventional techniques has described limitations. The aim of the case report is to demonstrate the use of CAD (Computer Aided Design) CAM (Computer Aided Manufacture) technology to produce an esthetic monolithic polymethylmethacrylate prosthesis that is retentive and stable on insertion. Adolescent oligodontia patients are typically not suitable candidates for dental implant therapy. Overdentures provide interim or definitive restorative advantages. Given the important esthetic, psychological, and social functions of the prosthesis, an important therapeutic goal for the overdenture prosthesis is esthetics. A CAD-CAM approach to overdenture manufacture can provide a highly esthetic, strong, and retentive prosthesis. CAD-CAM manufacture of monolithic acrylic overdentures offer several advantages that include (1) improved planning and clinical communication, (2) high fidelity manufacture, (3) improved flexural strength, impact strength, and porosity, (4) improved prosthesis integrity and durability (due to the monolithic design), (5) CNC control of occlusal contacts, (6) high esthetic potential due to quality of bulk material and iterative design, and (7) archival nature of the digital prosthesis. CAD-CAM manufacture of monolithic overdentures is a viable approach to completing high value esthetic management of the adolescent oligodontia patient. This case report identifies a new way to utilize CAD CAM technology to produce an improved overdenture for the oligodontia patient. It will be of interest to many and underscores the fundamental principles of smile design transfer to the digital environment. (J Esthet Restor Dent, 2016). © 2016 Wiley Periodicals, Inc.

A Review of the Aging Process and Facilities Topic.

PubMed

Jornitz, Maik W

2015-01-01

Aging facilities have become a concern in the pharmaceutical and biopharmaceutical manufacturing industry, so much that task forces are formed by trade organizations to address the topic. Too often, examples of aging or obsolete equipment, unit operations, processes, or entire facilities have been encountered. Major contributors to this outcome are the failure to invest in new equipment, disregarding appropriate maintenance activities, and neglecting the implementation of modern technologies. In some cases, a production process is insufficiently modified to manufacture a new product in an existing process that was used to produce a phased-out product. In other instances, manufacturers expanded the facility or processes to fulfill increasing demand and the scaling occurred in a non-uniform manner, which led to non-optimal results. Regulatory hurdles of post-approval changes in the process may thwart companies' efforts to implement new technologies. As an example, some changes have required 4 years to gain global approval. This paper will address cases of aging processes and facilities aside from modernizing options. © PDA, Inc. 2015.

Big Data Analysis of Manufacturing Processes

NASA Astrophysics Data System (ADS)

Windmann, Stefan; Maier, Alexander; Niggemann, Oliver; Frey, Christian; Bernardi, Ansgar; Gu, Ying; Pfrommer, Holger; Steckel, Thilo; Krüger, Michael; Kraus, Robert

2015-11-01

The high complexity of manufacturing processes and the continuously growing amount of data lead to excessive demands on the users with respect to process monitoring, data analysis and fault detection. For these reasons, problems and faults are often detected too late, maintenance intervals are chosen too short and optimization potential for higher output and increased energy efficiency is not sufficiently used. A possibility to cope with these challenges is the development of self-learning assistance systems, which identify relevant relationships by observation of complex manufacturing processes so that failures, anomalies and need for optimization are automatically detected. The assistance system developed in the present work accomplishes data acquisition, process monitoring and anomaly detection in industrial and agricultural processes. The assistance system is evaluated in three application cases: Large distillation columns, agricultural harvesting processes and large-scale sorting plants. In this paper, the developed infrastructures for data acquisition in these application cases are described as well as the developed algorithms and initial evaluation results.

Manufacture of threads with variable pitch by using noncircular gears

NASA Astrophysics Data System (ADS)

Slătineanu, L.; Dodun, O.; Coteață, M.; Coman, I.; Nagîț, G.; Beșliu, I.

2016-08-01

There are mechanical equipments in which shafts threaded with variable pitch are included. Such a shaft could be met in the case of worm specific to the double enveloping worm gearing. Over the years, the researchers investigated some possibilities to geometrically define and manufacture the shaft zones characterized by a variable pitch. One of the methods able to facilitate the manufacture of threads with variable pitch is based on the use of noncircular gears in the threading kinematic chain for threading by cutting. In order to design the noncircular gears, the mathematical law of pitch variation has to be known. An analysis of pitch variation based on geometrical considerations was developed in the case of a double enveloping globoid worm. Subsequently, on the bases of a proper situation, a numerical model was determined. In this way, an approximately law of pitch variation was determined and it could be taken into consideration when designing the noncircular gears included in the kinematic chain of the cutting machine tool.

Evaluation of Ophthalmic Surgical Instrument Sterility Using Short-Cycle Sterilization for Sequential Same-Day Use.

PubMed

Chang, David F; Hurley, Nikki; Mamalis, Nick; Whitman, Jeffrey

2018-03-27

The common practice of short-cycle sterilization for ophthalmic surgical instrumentation has come under increased regulatory scrutiny. This study was undertaken to evaluate the efficacy of short-cycle sterilization processing for consecutive same-day cataract procedures. Testing of specific sterilization processing methods by an independent medical device validation testing laboratory. Phaco handpieces from 3 separate manufacturers were tested along with appropriate biologic indicators and controls using 2 common steam sterilizers. A STATIM 2000 sterilizer (SciCan, Canonsburg, PA) with the STATIM metal cassette, and an AMSCO Century V116 pre-vacuum sterilizer (STERIS, Mentor, OH) using a Case Medical SteriTite container (Case Medical, South Hackensack, NJ) rigid container were tested using phaco tips and handpieces from 3 different manufacturers. Biological indicators were inoculated with highly resistant Geobacillus stearothermophilus, and each sterility verification test was performed in triplicate. Both wrapped and contained loads were tested with full dry cycles and a 7-day storage time to simulate prolonged storage. In adherence with the manufacturers' instructions for use (IFU), short cycles (3.0-3.5-minute exposure times) for unwrapped and contained loads were also tested after only 1 minute of dry time to simulate use on a consecutive case. Additional studies were performed to demonstrate whether any moisture present in the load containing phaco handpieces postprocessing was sterile and would affect the sterility of the contents after a 3-minute transit/storage time. This approximated the upper limit of time needed to transfer a containment device to the operating room. Presence or absence of microbial growth from cultured test samples. All inoculated test samples from both sterilizers were negative for growth of the target organism whether the full dry phase was interrupted or not. Pipetted postprocessing moisture samples and swabs of the handpieces were also negative for growth after a 3-minute transit/storage time. These studies support the use of unwrapped, short-cycle sterilization that adheres to the IFU of these 2 popular Food and Drug Administration-cleared sterilizers for sequential same-day cataract surgeries. A full drying phase is not necessary when the instruments are kept within the covered sterilizer containment device for prompt use on a sequential case. Copyright © 2018 American Academy of Ophthalmology. Published by Elsevier Inc. All rights reserved.

Investigations on the corrosion resistance of metallic bipolar plates (BPP) in proton exchange membrane fuel cells (PEMFC) - understanding the effects of material, coating and manufacturing

NASA Astrophysics Data System (ADS)

Dur, Ender

Polymer Electrolyte Membrane Fuel Cell (PEMFC) systems are promising technology for contributing to meet the deficiency of world`s clean and sustainable energy requirements in the near future. Metallic bipolar plate (BPP) as one of the most significant components of PEMFC device accounts for the largest part of the fuel cell`s stack. Corrosion for metallic bipolar plates is a critical issue, which influences the performance and durability of PEMFC. Corrosion causes adverse impacts on the PEMFC`s performance jeopardizing commercialization. This research is aimed at determining the corrosion resistance of metallic BPPs, particularly stainless steels, used in PEMFC from different aspects. Material selection, coating selection, manufacturing process development and cost considerations need to be addressed in terms of the corrosion behavior to justify the use of stainless steels as a BPP material in PEMFC and to make them commercially feasible in industrial applications. In this study, Ti, Ni, SS304, SS316L, and SS 430 blanks, and BPPs comprised of SS304 and SS316L were examined in terms of the corrosion behavior. SS316L plates were coated to investigate the effect of coatings on the corrosion resistance performance. Stamping and hydroforming as manufacturing processes, and three different coatings (TiN, CrN, ZrN) applied via the Physical Vapor Deposition (PVD) method in three different thicknesses were selected to observe the effects of manufacturing processes, coating types and coating thicknesses on the corrosion resistance of BPP, respectively. Uncoated-coated blank and formed BPP were subjected to two different corrosion tests: potentiostatic and potentiodynamic. Some of the substantial results: 1- Manufacturing processes have an adverse impact on the corrosion resistance. 2- Hydroformed plates have slightly higher corrosion resistance than stamped samples. 3- BPPs with higher channel size showed better corrosion resistance. 4- Since none of the uncoated samples meet the 2015 target of the U.S. Department of Energy, surface coating is required. 5- ZrN and CrN coated BPPs exhibited higher corrosion resistance meeting DOE target while TiN coated samples had the lowest corrosion resistance. Higher coating thicknesses improved the corrosion resistance of the BPPs. 6- Process sequence between coating and manufacturing is not significant for hydroforming case (ZrN and CrN) and stamping case (CrN) in terms of the corrosion resistance. In other words, coating the BPP`s substrate material before manufacturing process does not always decrease the corrosion resistance of the BPPs.

Comparative study of material loss at the taper interface in retrieved metal-on-polyethylene and metal-on-metal femoral components from a single manufacturer.

PubMed

Bills, Paul; Racasan, Radu; Bhattacharya, Saugatta; Blunt, Liam; Isaac, Graham

2017-08-01

There have been a number of reports on the occurrence of taper corrosion and/or fretting and some have speculated on a link to the occurrence of adverse local tissue reaction specifically in relation to total hip replacement which have a metal-on-metal bearing. As such a study was carried out to compare the magnitude of material loss at the taper in a series of retrieved femoral heads used in metal-on-polyethylene bearings with that in a series of retrieved heads used in metal-on-metal bearings. A total of 36 metal-on-polyethylene and 21 metal-on-metal femoral components were included in the study all of which were received from a customer complaint database. Furthermore, a total of nine as-manufactured femoral components were included to provide a baseline for characterisation. All taper surfaces were assessed using an established corrosion scoring method and measurements were taken of the female taper surface using a contact profilometry. In the case of metal-on-metal components, the bearing wear was also assessed using coordinate metrology to determine whether or not there was a relationship between bearing and taper material loss in these cases. The study found that in this cohort the median value of metal-on-polyethylene taper loss was 1.25 mm 3 with the consequent median value for metal-on-metal taper loss being 1.75 mm 3 . This study also suggests that manufacturing form can result in an apparent loss of material from the taper surface determined to have a median value of 0.59 mm 3 . Therefore, it is clear that form variability is a significant confounding factor in the measurement of material loss from the tapers of femoral heads retrieved following revision surgery.

Chairside Computer-Aided Design/Computer-Aided Manufacture All-Ceramic Crown and Endocrown Restorations: A 7-Year Survival Rate Study.

PubMed

Fages, Michel; Raynal, Jacques; Tramini, Paul; Cuisinier, Frédéric Jg; Durand, Jean-Cédric

The objective of the present study was to analyze the clinical outcomes of 447 monoblock ceramic chairside computer-aided design/computer-aided manufacture (CAD/CAM) reconstructions over a 7-year functional period. Of these reconstructions, 212 were peripheral crowns and 235 were endocrowns. The restorations were placed between 2003 and 2008 in a total of 323 patients. They were created using a chairside CAD/CAM method and the same materials in all cases. All of the crowns were manufactured and glued during the same clinical session by the same practitioner. Data were descriptively analyzed and survival probabilities were calculated using Kaplan-Meier statistics. Of the 447 restorations, only 6 failures occurred, resulting in a success rate of 98.66%. All of the failures were the result of a partial ceramic fracture. Of the six ceramic fractures, five appeared on peripheral crowns and one on an endocrown. All fractures appeared in the first 24 months, including two in the first month. Log-rank test comparing incidence rates between crowns and endocrowns showed no significant differences (P = .08). This survival rate study reinforced the use of CAD/CAM full ceramic crowns and endocrowns on molars, showing a much more favorable survival rate for endocrowns.

27 CFR 19.607 - Marks on cases.

Code of Federal Regulations, 2010 CFR

2010-04-01

.... Cases removed for export, transfer to customs bonded warehouses or customs manufacturing bonded warehouses, transfer to foreign-trade zones, or for use as supplies on certain vessels and aircraft, shall...; or (6) Labels or data describing the contents for commercial identification or accounting purposes...

Two Echelon Supply Chain Integrated Inventory Model for Similar Products: A Case Study

NASA Astrophysics Data System (ADS)

Parjane, Manoj Baburao; Dabade, Balaji Marutirao; Gulve, Milind Bhaskar

2017-06-01

The purpose of this paper is to develop a mathematical model towards minimization of total cost across echelons in a multi-product supply chain environment. The scenario under consideration is a two-echelon supply chain system with one manufacturer, one retailer and M products. The retailer faces independent Poisson demand for each product. The retailer and the manufacturer are closely coupled in the sense that the information about any depletion in the inventory of a product at a retailer's end is immediately available to the manufacturer. Further, stock-out is backordered at the retailer's end. Thus the costs incurred at the retailer's end are the holding costs and the backorder costs. The manufacturer has only one processor which is time shared among the M products. Production changeover from one product to another entails a fixed setup cost and a fixed set up time. Each unit of a product has a production time. Considering the cost components, and assuming transportation time and cost to be negligible, the objective of the study is to minimize the expected total cost considering both the manufacturer and retailer. In the process two aspects are to be defined. Firstly, every time a product is taken up for production, how much of it (production batch size, q) should be produced. Considering a large value of q favors the manufacturer while a small value of q suits the retailers. Secondly, for a given batch size q, at what level of retailer's inventory (production queuing point), the batch size S of a product be taken up for production by the manufacturer. A higher value of S incurs more holding cost whereas a lower value of S increases the chance of backorder. A tradeoff between the holding and backorder cost must be taken into consideration while choosing an optimal value of S. It may be noted that due to multiple products and single processor, a product `taken' up for production may not get the processor immediately, and may have to wait in a queue. The `S' should factor in the probability of waiting time in the queue.

Multiphysics modeling of selective laser sintering/melting

NASA Astrophysics Data System (ADS)

Ganeriwala, Rishi Kumar

A significant percentage of total global employment is due to the manufacturing industry. However, manufacturing also accounts for nearly 20% of total energy usage in the United States according to the EIA. In fact, manufacturing accounted for 90% of industrial energy consumption and 84% of industry carbon dioxide emissions in 2002. Clearly, advances in manufacturing technology and efficiency are necessary to curb emissions and help society as a whole. Additive manufacturing (AM) refers to a relatively recent group of manufacturing technologies whereby one can 3D print parts, which has the potential to significantly reduce waste, reconfigure the supply chain, and generally disrupt the whole manufacturing industry. Selective laser sintering/melting (SLS/SLM) is one type of AM technology with the distinct advantage of being able to 3D print metals and rapidly produce net shape parts with complicated geometries. In SLS/SLM parts are built up layer-by-layer out of powder particles, which are selectively sintered/melted via a laser. However, in order to produce defect-free parts of sufficient strength, the process parameters (laser power, scan speed, layer thickness, powder size, etc.) must be carefully optimized. Obviously, these process parameters will vary depending on material, part geometry, and desired final part characteristics. Running experiments to optimize these parameters is costly, energy intensive, and extremely material specific. Thus a computational model of this process would be highly valuable. In this work a three dimensional, reduced order, coupled discrete element - finite difference model is presented for simulating the deposition and subsequent laser heating of a layer of powder particles sitting on top of a substrate. Validation is provided and parameter studies are conducted showing the ability of this model to help determine appropriate process parameters and an optimal powder size distribution for a given material. Next, thermal stresses upon cooling are calculated using the finite difference method. Different case studies are performed and general trends can be seen. This work concludes by discussing future extensions of this model and the need for a multi-scale approach to achieve comprehensive part-level models of the SLS/SLM process.

Design and simulation of integration system between automated material handling system and manufacturing layout in the automotive assembly line

NASA Astrophysics Data System (ADS)

Seha, S.; Zamberi, J.; Fairu, A. J.

2017-10-01

Material handling system (MHS) is an important part for the productivity plant and has recognized as an integral part of today’s manufacturing system. Currently, MHS has growth tremendously with its technology and equipment type. Based on the case study observation, the issue involving material handling system contribute to the reduction of production efficiency. This paper aims to propose a new design of integration between material handling and manufacturing layout by investigating the influences of layout and material handling system. A method approach tool using Delmia Quest software is introduced and the simulation result is used to assess the influences of the integration between material handling system and manufacturing layout in the performance of automotive assembly line. The result show, the production of assembly line output increases more than 31% from the current system. The source throughput rate average value went up to 252 units per working hour in model 3 and show the effectiveness of the pick-to-light system as efficient storage equipment. Thus, overall result shows, the application of AGV and the pick-to-light system gave a large significant effect in the automotive assembly line. Moreover, the change of layout also shows a large significant improvement to the performance.

Interpreting cost of ownership for mix-and-match lithography

NASA Astrophysics Data System (ADS)

Levine, Alan L.; Bergendahl, Albert S.

1994-05-01

Cost of ownership modeling is a critical and emerging tool that provides significant insight into the ways to optimize device manufacturing costs. The development of a model to deal with a particular application, mix-and-match lithography, was performed in order to determine the level of cost savings and the optimum ways to create these savings. The use of sensitivity analysis with cost of ownership allows the user to make accurate trade-offs between technology and cost. The use and interpretation of the model results are described in this paper. Parameters analyzed include several manufacturing considerations -- depreciation, maintenance, engineering and operator labor, floorspace, resist, consumables and reticles. Inherent in this study is the ability to customize this analysis for a particular operating environment. Results demonstrate the clear advantages of a mix-and-match approach for three different operating environments. These case studies also demonstrate various methods to efficiently optimize cost savings strategies.

Long-term health experience of jet engine manufacturing workers: VI: incidence of malignant central nervous system neoplasms in relation to estimated workplace exposures.

PubMed

Marsh, Gary M; Youk, Ada O; Buchanich, Jeanine M; Xu, Hui; Downing, Sarah; Kennedy, Kathleen J; Esmen, Nurtan A; Hancock, Roger P; Lacey, Steven E; Fleissner, Mary Lou

2013-06-01

To determine whether glioblastoma (GB) incidence rates among jet engine manufacturing workers were associated with specific chemical or physical exposures. Subjects were 210,784 workers employed from 1952 to 2001. We conducted a cohort incidence study and two nested case-control studies with focus on the North Haven facility where we previously observed a not statistically significant overall elevation in GB rates. We estimated individual-level exposure metrics for 11 agents. In the total cohort, none of the agent metrics considered was associated with increased GB risk. The GB incidence rates in North Haven were also not related to workplace exposures, including the "blue haze" exposure unique to North Haven. If not due to chance alone, GB rates in North Haven may reflect external occupational factors, nonoccupational factors, or workplace factors unique to North Haven unmeasured in the current evaluation.

Continuous Manufacturing of Recombinant Therapeutic Proteins: Upstream and Downstream Technologies.

PubMed

Patil, Rohan; Walther, Jason

2017-03-07

Continuous biomanufacturing of recombinant therapeutic proteins offers several potential advantages over conventional batch processing, including reduced cost of goods, more flexible and responsive manufacturing facilities, and improved and consistent product quality. Although continuous approaches to various upstream and downstream unit operations have been considered and studied for decades, in recent years interest and application have accelerated. Researchers have achieved increasingly higher levels of process intensification, and have also begun to integrate different continuous unit operations into larger, holistically continuous processes. This review first discusses approaches for continuous cell culture, with a focus on perfusion-enabling cell separation technologies including gravitational, centrifugal, and acoustic settling, as well as filtration-based techniques. We follow with a review of various continuous downstream unit operations, covering categories such as clarification, chromatography, formulation, and viral inactivation and filtration. The review ends by summarizing case studies of integrated and continuous processing as reported in the literature.

Readiness for change and job satisfaction in a case of lean management application - a comparative study.

PubMed

Lipińska-Grobelny, Agnieszka; Papieska, Ewelina

2012-09-01

This current study investigates the effect of lean management system on work attitudes of workers of two manufacturing companies. "Lean management" is a concept of work processes and human relations that determines company's productivity and profitability. Workers of two enterprises, the first one with lean production and the second one with old mass production, were compared for their readiness for change and job satisfaction (both emotional and cognitive aspect). The sample of 102 employees completed a battery of instruments such as: the Job Description Inventory by Neuberger and Allerbeck, the Job Affect Scale by Burke et al. and the Change-Readiness Scale by Kriegel and Brandt. Individuals from the lean manufacturing company were characterized by higher level of readiness for change, positive affect at work, and cognitive job satisfaction. In this approach the introduction of lean production positively affected company's human resource attitudes.

Fashion garment manufacturing - FGM and cyclability theory

NASA Astrophysics Data System (ADS)

Mendes, F. D.; Dos Santos, M. C. L.

2017-10-01

This article, derived from an ongoing research, presents the possibilities of reducing the inappropriate disposal of textile residues generated by the fabric cutting sector of the Fashion Garment Manufacturing (FGM). The raw material used is very varied, resulting in a large number of productive processes. FGM produces clothing that has as its main features a short life cycle, a high rate of diversification and differentiation, and small production batches, resulting in few similar parts. The production process is differentiated according to the characteristics of the fabric and the look of the garment. During the production process, at least 10% of textile waste is generated during the cutting process, which is constantly discarded in an inadequate way. The Cyclability theory is researched aiming at the possibility of reduction in the generation of waste and elimination of inappropriate disposal. The case study presents the action research carried out in three small Brazilian companies to study the applicability of the Cyclability theory.

Injection molded polymer optics in the 21st Century

NASA Astrophysics Data System (ADS)

Beich, William S.

2005-08-01

Precision polymer optics, manufactured by injection molding techniques, has been a key enabling technology for several decades now. The technology, which can be thought of as a subset of the wider field of precision optics manufacturing, was pioneered in the United States by companies such as Eastman Kodak, US Precision Lens, and Polaroid. In addition to suppliers in the U.S. there are several companies worldwide that design and manufacture precision polymer optics, for example Philips High Tech Plastics in Europe and Fujinon in Japan. Designers who are considering using polymer optics need a fundamental understanding of exactly how the optics are created. This paper will survey the technology and processes that are employed in the successful implementation of a polymer optic solution from a manufacturer's perspective. Special emphasis will be paid to the unique relationship between the molds and the optics that they produce. We will discuss the key elements of production: molding resins, molds and molding equipment, and metrology. Finally we will offer a case study to illustrate just how the optics designer carries a design concept through to production. The underlying theme throughout the discussion of polymer optics is the need for the design team to work closely with an experienced polymer optics manufacturer with a solid track record of success in molded optics. As will be seen shortly, the complex interaction between thermoplastics, molds, and molding machines dictates the need for working closely with a supplier who has the critical knowledge needed to manage all aspects of the program.

A Hospital Is Not Just a Factory, but a Complex Adaptive System-Implications for Perioperative Care.

PubMed

Mahajan, Aman; Islam, Salim D; Schwartz, Michael J; Cannesson, Maxime

2017-07-01

Many methods used to improve hospital and perioperative services productivity and quality of care have assumed that the hospital is essentially a factory, and therefore, that industrial engineering and manufacturing-derived redesign approaches such as Six Sigma and Lean can be applied to hospitals and perioperative services just as they have been applied in factories. However, a hospital is not merely a factory but also a complex adaptive system (CAS). The hospital CAS has many subsystems, with perioperative care being an important one for which concepts of factory redesign are frequently advocated. In this article, we argue that applying only factory approaches such as lean methodologies or process standardization to complex systems such as perioperative care could account for difficulties and/or failures in improving performance in care delivery. Within perioperative services, only noncomplex/low-variance surgical episodes are amenable to manufacturing-based redesign. On the other hand, complex surgery/high-variance cases and preoperative segmentation (the process of distinguishing between normal and complex cases) can be viewed as CAS-like. These systems tend to self-organize, often resist or react unpredictably to attempts at control, and therefore require application of CAS principles to modify system behavior. We describe 2 examples of perioperative redesign to illustrate the concepts outlined above. These examples present complementary and contrasting cases from 2 leading delivery systems. The Mayo Clinic example illustrates the application of manufacturing-based redesign principles to a factory-like (high-volume, low-risk, and mature practice) clinical program, while the Kaiser Permanente example illustrates the application of both manufacturing-based and self-organization-based approaches to programs and processes that are not factory-like but CAS-like. In this article, we describe how factory-like processes and CAS can coexist within a hospital and how self-organization-based approaches can be used to improve care delivery in many situations where manufacturing-based approaches may not be appropriate.

Comparison of three methods for wind turbine capacity factor estimation.

PubMed

Ditkovich, Y; Kuperman, A

2014-01-01

Three approaches to calculating capacity factor of fixed speed wind turbines are reviewed and compared using a case study. The first "quasiexact" approach utilizes discrete wind raw data (in the histogram form) and manufacturer-provided turbine power curve (also in discrete form) to numerically calculate the capacity factor. On the other hand, the second "analytic" approach employs a continuous probability distribution function, fitted to the wind data as well as continuous turbine power curve, resulting from double polynomial fitting of manufacturer-provided power curve data. The latter approach, while being an approximation, can be solved analytically thus providing a valuable insight into aspects, affecting the capacity factor. Moreover, several other merits of wind turbine performance may be derived based on the analytical approach. The third "approximate" approach, valid in case of Rayleigh winds only, employs a nonlinear approximation of the capacity factor versus average wind speed curve, only requiring rated power and rotor diameter of the turbine. It is shown that the results obtained by employing the three approaches are very close, enforcing the validity of the analytically derived approximations, which may be used for wind turbine performance evaluation.

[Evidential value of dental materials identification by infrared spectroscopy in forensic medicine opinionating].

PubMed

Wachowiak, Roman; Strach, Bogna

2007-01-01

The potential for a release of dental restoration material or a spontaneous loss of a tooth structure fragment in the course of mastication frequently requires a reliable identification of the lost fragment in order to confirm its origin. The consequences of incidental mechanical injuries -- in view of the presence of dangerous solid fragments -- become particularly important in cases of using a chewing gum. The problem involves distinguishing between the structure of a fragment of restoration or a broken tooth structure and incidental contaminants of chewing gum produced in the process of gum manufacturing. The consequences of mechanical injuries or exposure to potential structural tooth damage in the course of gum chewing provide a subject for numerous litigations against manufacturer of chewing gum and require appropriate identification of the material. The studies were conducted using solid phase infrared spectroscopy in the range of 500-4000 wavelength (cm(-1)) for a quick identification of dental materials used in the dental practice. A database of infrared transmission spectra characteristic of commonly employed dental filling materials was prepared to provide a systemic reference system, useful in controversial interpretation cases.

Software for improving the quality of project management, a case study: international manufacture of electrical equipment

NASA Astrophysics Data System (ADS)

Preradović, D. M.; Mićić, Lj S.; Barz, C.

2017-05-01

Production conditions in today’s world require software support at every stage of production and development of new products, for quality assurance and compliance with ISO standards. In addition to ISO standards such as usual metrics of quality, companies today are focused on other optional standards, such as CMMI (Capability Maturity Model Integrated) or prescribing they own standards. However, while there is intensive progress being made in the PM (project management), there is still a significant number of projects, at the global level, that are failures. These have failed to achieve their goals, within budget or timeframe. This paper focuses on checking the role of software tools through the rate of success in projects implemented in the case of internationally manufactured electrical equipment. The results of this research show the level of contribution of the project management software used to manage and develop new products to improve PM processes and PM functions, and how selection of the software tools affects the quality of PM processes and successfully completed projects.

A comparative assessment of solar thermal electric power plants in the 1-10 MWe range

NASA Technical Reports Server (NTRS)

Rosenberg, L. S.; Revere, W. R.

1981-01-01

The candidate power system technologies were ranked in terms of the cost of electric energy each system produces. In all cases, it was assumed that development programs would result in mature power plant systems that could be commercially manufactured. The results of the study, a brief description of the systems examined, and the methodologies used are presented.

A Case Study of the NATO Identification System (NIS) Codevelopment Program

DTIC Science & Technology

1988-09-01

the otherhand are unrelated to the military equipment being purchased. These offsets include foreign investment, technology transfer, and countertrade ...manufacturer and a foreign entity. 6. Countertrade - a transaction that specifies the exchange of selected goods and services for another of equivalent...arrangements. In fact, U.S. agencies are permitted to provide advisory and marketing intelligence services to U.S. exporters involved in countertrade

Research on seamless development of surgical instruments based on biological mechanisms using CAD and 3D printer.

PubMed

Yamamoto, Ikuo; Ota, Ren; Zhu, Rui; Lawn, Murray; Ishimatsu, Takakazu; Nagayasu, Takeshi; Yamasaki, Naoya; Takagi, Katsunori; Koji, Takehiko

2015-01-01

In the area of manufacturing surgical instruments, the ability to rapidly design, prototype and test surgical instruments is critical. This paper provides a simple case study of the rapid development of two bio-mechanism based surgical instruments which are ergonomic, aesthetic and were successfully designed, prototyped and conceptually tested in a very short period of time.

Newly invented biobased materials from low-carbon, diverted waste fibers: research methods, testing, and full-scale application in a case study structure

Treesearch

Julee A Herdt; John Hunt; Kellen Schauermann

2016-01-01

This project demonstrates newly invented, biobased construction materials developed by applying lowcarbon, biomass waste sources through the Authors’ engineered fiber processes and technology. If manufactured and applied large-scale the project inventions can divert large volumes of cellulose waste into high-performance, low embodied energy, environmental construction...

Architectural Design Education: Designing a Library, Public Communication and Information Center in the Manufacturing Zone of Central Eskis, Ehir Turkey, a Case Study

ERIC Educational Resources Information Center

Caglar, Nur; Uludag, Zeynep

2006-01-01

It is a fact that architectural design education has become the focus of an extremely complicated set of issues and conscientious debates. Therefore, to extend and challenge educational understanding in architecture it becomes crucial to exchange pedagogical practices. In this article, a specific theoretical approach and teaching methodology,…

The evaluation of a new technology for gunshot residue (GSR) analysis in the field

NASA Astrophysics Data System (ADS)

Hondrogiannis, Ellen; Andersen, Danielle; Miziolek, Andrzej W.

2013-05-01

There continues to be a need for improved technology to be used in theater to quickly and accurately identify the person who shot any weapon during a terrorist attack as well as to link a suspect to the actual weapon fired during a crime. Beyond this, in areas of conflict it would be desirable to have the capability to establish the source country for weaponry and ammunition. Gunshot residue (GSR) analysis is a reasonably well-studied technology area. Recent scientific publications have reported that the residues have a rich composition of both organic and inorganic compounds. For the purposes of identifying the manufacturer or country of origin for the ammunition, the inorganic components of GSR appear to be especially promising since their presence in the propellant and primer formulations are either specific to a given chemical formula, or they represent impurities in the manufacturing process that can be unique to a manufacturer or the source country for the chemicals used for propellants and primers. The Laser Induced Breakdown Spectroscopy (LIBS) technology has already demonstrated considerable capability for elemental fingerprinting, especially for inorganic/metallic components. A number of reports have demonstrated LIBS capability in forensics for matching materials such as inks, fabrics, paper, glass, and paint. This work describes the encouraging results of an initial study to assess a new commercial field-portable (battery operated) LIBS system for GSR analysis with gunshot residues having been collected from inside cartridge casings from 3 different ammunition manufacturers.

40 CFR 90.119 - Certification procedure-testing.

Code of Federal Regulations, 2010 CFR

2010-07-01

... must select the duty cycle that will result in worst-case emission results for certification. For any... facility, in which case instrumentation and equipment specified by the Administrator must be made available... manufacturers may not use any equipment, instruments, or tools to identify malfunctioning, maladjusted, or...

77 FR 54933 - Government-Owned Inventions, Available for Licensing

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-06

... Manufacture, Copoly(imide Oxetane)s Containing Pendant Fluorocarbon Moieties, Oligomers and Processes Therefor...; NASA Case No.: LAR-17895-1: Physiologically Modulating Videogames or Simulations Which Use Motion... Crimped Connector; NASA Case No.: LAR-18006-1: Process and Apparatus for Nondestructive Evaluation of the...