Map showing selected surface-water data for the Alton-Kolob coal-fields area, Utah

USGS Publications Warehouse

Price, Don

1982-01-01

This is one of a series of maps that describe the geology and related natural resources of the Alton-Kolob coal-fields area, Utah. Streamflow records used to compile the map and the following table were collected by the U.S. Geological Survey in cooperation with the Utah Department of Natural Resources, Division of Water Rights, and the Utah Department of Transportation. The principal runoff-producing areas were delineated form a work map (scale 1:250,000) compiled to estimate water yields in Utah (Bagley and others, 1964).

The Difference Between the Potentiometric Surfaces of the Magothy Aquifer in Southern Maryland, September 1975 and September 2009

USGS Publications Warehouse

Curtin, Stephen E.; Andreasen, David C.; Staley, Andrew W.

2010-01-01

This report presents a map showing the change in the potentiometric surface of the Magothy aquifer in the Magothy Formation of Late Cretaceous age in Southern Maryland between September 1975 and September 2009. The map, based on water level differences obtained from 48 wells, shows that during the 34-year period, the potentiometric surface had little change at the outcrop area, which is in the northernmost part of the study area, but declined 75 feet at Waldorf. Waldorf is located near the southwesternmost part of the study area, and approaches the downdip boundary of the aquifer. The map also shows well yield in gallons per day for 2008 at wells or well fields.

Tuberculosis disease mapping in Kedah using standardized morbidity ratio

NASA Astrophysics Data System (ADS)

Diah, Ijlal Mohd; Aziz, Nazrina; Kasim, Maznah Mat

2017-10-01

This paper presents the results of relative risk estimation that applied to TB data in Kedah using the most common approach, Standardized Morbidity Ratio (SMR). Disease mapping has been recognized as one of the methods that can be used by government and public health in order to control diseases since it can give a clear picture of the risk areas. To get good disease mapping, relative risk estimation is an important issue that need to be considered. TB risk areas will be recognized through the map. From the result, Kulim shows the lowest risk areas of contracting TB while Kota Setar has the highest risk area.

Map showing principal drainage basins, principal runoff-producing areas, and selected stream flow data in the Kaiparowits coal-basin area, Utah

USGS Publications Warehouse

Price, Don

1978-01-01

This is one of a series of maps that describe the geology and related natural resources in the Kaiparowits coal-basin area. Streamflow records used to compile this map and the accompanying table were collected by the U.S. Geological Survey in cooperation with the Utah State Engineer and the Utah Department of Transportation. The principal runoff-producing areas were delineated from a work map (scale 1:250,000) compiled to estimate water yields in Utah (Bagley and others, 1964). Information about Lake Powell was furnished by the U.S. Bureau of Reclamation.

Automating the selection of standard parallels for conic map projections

NASA Astrophysics Data System (ADS)

Šavriǒ, Bojan; Jenny, Bernhard

2016-05-01

Conic map projections are appropriate for mapping regions at medium and large scales with east-west extents at intermediate latitudes. Conic projections are appropriate for these cases because they show the mapped area with less distortion than other projections. In order to minimize the distortion of the mapped area, the two standard parallels of conic projections need to be selected carefully. Rules of thumb exist for placing the standard parallels based on the width-to-height ratio of the map. These rules of thumb are simple to apply, but do not result in maps with minimum distortion. There also exist more sophisticated methods that determine standard parallels such that distortion in the mapped area is minimized. These methods are computationally expensive and cannot be used for real-time web mapping and GIS applications where the projection is adjusted automatically to the displayed area. This article presents a polynomial model that quickly provides the standard parallels for the three most common conic map projections: the Albers equal-area, the Lambert conformal, and the equidistant conic projection. The model defines the standard parallels with polynomial expressions based on the spatial extent of the mapped area. The spatial extent is defined by the length of the mapped central meridian segment, the central latitude of the displayed area, and the width-to-height ratio of the map. The polynomial model was derived from 3825 maps-each with a different spatial extent and computationally determined standard parallels that minimize the mean scale distortion index. The resulting model is computationally simple and can be used for the automatic selection of the standard parallels of conic map projections in GIS software and web mapping applications.

An image-space parallel convolution filtering algorithm based on shadow map

NASA Astrophysics Data System (ADS)

Li, Hua; Yang, Huamin; Zhao, Jianping

2017-07-01

Shadow mapping is commonly used in real-time rendering. In this paper, we presented an accurate and efficient method of soft shadows generation from planar area lights. First this method generated a depth map from light's view, and analyzed the depth-discontinuities areas as well as shadow boundaries. Then these areas were described as binary values in the texture map called binary light-visibility map, and a parallel convolution filtering algorithm based on GPU was enforced to smooth out the boundaries with a box filter. Experiments show that our algorithm is an effective shadow map based method that produces perceptually accurate soft shadows in real time with more details of shadow boundaries compared with the previous works.

Benthic Habitat Mapping by Combining Lyzenga’s Optical Model and Relative Water Depth Model in Lintea Island, Southeast Sulawesi

NASA Astrophysics Data System (ADS)

Hafizt, M.; Manessa, M. D. M.; Adi, N. S.; Prayudha, B.

2017-12-01

Benthic habitat mapping using satellite data is one challenging task for practitioners and academician as benthic objects are covered by light-attenuating water column obscuring object discrimination. One common method to reduce this water-column effect is by using depth-invariant index (DII) image. However, the application of the correction in shallow coastal areas is challenging as a dark object such as seagrass could have a very low pixel value, preventing its reliable identification and classification. This limitation can be solved by specifically applying a classification process to areas with different water depth levels. The water depth level can be extracted from satellite imagery using Relative Water Depth Index (RWDI). This study proposed a new approach to improve the mapping accuracy, particularly for benthic dark objects by combining the DII of Lyzenga’s water column correction method and the RWDI of Stumpt’s method. This research was conducted in Lintea Island which has a high variation of benthic cover using Sentinel-2A imagery. To assess the effectiveness of the proposed new approach for benthic habitat mapping two different classification procedures are implemented. The first procedure is the commonly applied method in benthic habitat mapping where DII image is used as input data to all coastal area for image classification process regardless of depth variation. The second procedure is the proposed new approach where its initial step begins with the separation of the study area into shallow and deep waters using the RWDI image. Shallow area was then classified using the sunglint-corrected image as input data and the deep area was classified using DII image as input data. The final classification maps of those two areas were merged as a single benthic habitat map. A confusion matrix was then applied to evaluate the mapping accuracy of the final map. The result shows that the new proposed mapping approach can be used to map all benthic objects in all depth ranges and shows a better accuracy compared to that of classification map produced using only with DII.

Preliminary map showing limonitic areas in the Silver City 1 degree by 2 degrees Quadrangle, Arizona and New Mexico

USGS Publications Warehouse

Raines, Gary L.

1984-01-01

This map is a part of a folio of maps of the Silver City 1o x 2o quadrangle, Arizona and New Mexico, prepared under the Conterminous United States Mineral Assessment Program. As a part of this study Landstat images were used to map the anomalous areas of limonitic materials as a guide to hydrothermal alteration which, in turn, acts as a guide to mineralized systems. The term limonite, defined by Blanchard (1968) as a general term for undifferentiated ferric oxide percipitates, is here modified to include any mineral with the typical spectral reflectance properties of the ferric oxide minerals such as hematite and goethite, as defined by Hunt (1980). The nap shows anomalous areas of limonitic miaterials that might be associated with mineralization. 

Topographic maps: Tools for planning

USGS Publications Warehouse

Kaufman, George A.

1980-01-01

Topographic maps are a detailed record of a land area, giving geographic positions and elevations for both natural and man-made features. They show the shape of the land the mountains, valleys, and plains by means of brown contour lines (lines of equal elevation above sea level). In steep mountainous areas, contours are closely spaced; in flatter areas, they are far apart. The elevation of any point on the map can be estimated by referring to the elevations of the contour lines above and below it.

Use of slope, aspect, and elevation maps derived from digital elevation model data in making soil surveys

USGS Publications Warehouse

Klingebiel, A.A.; Horvath, E.H.; Moore, D.G.; Reybold, W.U.

1987-01-01

Maps showing different classes of slope, aspect, and elevation were developed from U.S. Geological Survey digital elevation model data. The classes were displayed on clear Mylar at 1:24 000-scale and registered with topographic maps and orthophotos. The maps were used with aerial photographs, topographic maps, and other resource data to determine their value in making order-three soil surveys. They were tested on over 600 000 ha in Wyoming, Idaho, and Nevada under various climatic and topographic conditions. Field evaluations showed that the maps developed from digital elevation model data were accurate, except for slope class maps where slopes were <4%. The maps were useful to soil scientists, especially where (i) class boundaries coincided with soil changes, landform delineations, land use and management separations, and vegetation changes, and (ii) rough terrain and dense vegetation made it difficult to traverse the area. In hot, arid areas of sparse vegetation, the relationship of slope classes to kinds of soil and vegetation was less significant.

Remotely sensed high resolution irrigated area mapping in India for 2000 to 2015

PubMed Central

Ambika, Anukesh Krishnankutty; Wardlow, Brian; Mishra, Vimal

2016-01-01

India is among the countries that uses a significant fraction of available water for irrigation. Irrigated area in India has increased substantially after the Green revolution and both surface and groundwater have been extensively used. Under warming climate projections, irrigation frequency may increase leading to increased irrigation water demands. Water resources planning and management in agriculture need spatially-explicit irrigated area information for different crops and different crop growing seasons. However, annual, high-resolution irrigated area maps for India for an extended historical record that can be used for water resources planning and management are unavailable. Using 250 m normalized difference vegetation index (NDVI) data from Moderate Resolution Imaging Spectroradiometer (MODIS) and 56 m land use/land cover data, high-resolution irrigated area maps are developed for all the agroecological zones in India for the period of 2000–2015. The irrigated area maps were evaluated using the agricultural statistics data from ground surveys and were compared with the previously developed irrigation maps. High resolution (250 m) irrigated area maps showed satisfactory accuracy (R2=0.95) and can be used to understand interannual variability in irrigated area at various spatial scales. PMID:27996974

Hydrocarbon Reservoir Identification in Volcanic Zone by using Magnetotelluric and Geochemistry Information

NASA Astrophysics Data System (ADS)

Firda, S. I.; Permadi, A. N.; Supriyanto; Suwardi, B. N.

2018-03-01

The resistivity of Magnetotelluric (MT) data show the resistivity mapping in the volcanic reservoir zone and the geochemistry information for confirm the reservoir and source rock formation. In this research, we used 132 data points divided with two line at exploration area. We used several steps to make the resistivity mapping. There are time series correction, crosspower correction, then inversion of Magnetotelluric (MT) data. Line-2 and line-3 show anomaly geological condition with Gabon fault. The geology structure from the resistivity mapping show the fault and the geological formation with the geological rock data mapping distribution. The geochemistry information show the maturity of source rock formation. According to core sample analysis information, we get the visual porosity for reservoir rock formation in several geological structure. Based on that, we make the geological modelling where the potential reservoir and the source rock around our interest area.

Color Map of Ceres Elliptical Projection

NASA Image and Video Library

2016-03-22

This global map elliptical map from NASA Dawn spacecraft shows the surface of Ceres in enhanced color, encompassing infrared wavelengths beyond human visual range. Some areas near the poles are black where Dawn color imaging coverage is incomplete.

Topographic map analysis to determine Arjuno-Welirang volcanostratigraphy and implication for geothermal exploration

NASA Astrophysics Data System (ADS)

Apriani, Lestari; Satriana, Joshua; Aulian Chalik, Citra; Syahputra Mulyana, Reza; Hafidz, Muhammad; Suryantini

2017-12-01

Volcanostratigraphy study is used for supporting geothermal exploration on preliminary survey. This study is important to identify volcanic eruption center which shows potential area of geothermal heat source. The purpose of volcanostratigraphy study in research area is going to distinguish the characteristics of volcanic eruption product that construct the volcanic body. The analysis of Arjuno-Welirang volcanostratigraphy identification are based on topographic maps of Malang sheet with 1:100.000 scale, 1:50.000 scale, and a geological map. Regarding to the delineation of ridge and river, we determine five crowns, three hummocks, one brigade and one super brigade. The crowns consist of Ringgit, Welirang, Arjuno, Kawi, and Penanggungan, the hummocks comprise of Kembar III, Kembar II, and Kembar I, the brigade is Arjuno-Welirang, and the super brigade is Tengger. Based on topographic map interpretation and geothermal prospect evaluation method analysis, shows that Arjuno-Welirang prospect area have good geothermal resource potential.

A GIS/Remote Sensing-based methodology for groundwater potentiality assessment in Tirnavos area, Greece

NASA Astrophysics Data System (ADS)

Oikonomidis, D.; Dimogianni, S.; Kazakis, N.; Voudouris, K.

2015-06-01

The aim of this paper is to assess the groundwater potentiality combining Geographic Information Systems and Remote Sensing with data obtained from the field, as an additional tool to the hydrogeological research. The present study was elaborated in the broader area of Tirnavos, covering 419.4 km2. The study area is located in Thessaly (central Greece) and is crossed by two rivers, Pinios and Titarisios. Agriculture is one of the main elements of Thessaly's economy resulting in intense agricultural activity and consequently increased exploitation of groundwater resources. Geographic Information Systems (GIS) and Remote Sensing (RS) were used in order to create a map that depicts the likelihood of existence of groundwater, consisting of five classes, showing the groundwater potentiality and ranging from very high to very low. The extraction of this map is based on the study of input data such as: rainfall, potential recharge, lithology, lineament density, slope, drainage density and depth to groundwater. Weights were assigned to all these factors according to their relevance to groundwater potential and eventually a map based on weighted spatial modeling system was created. Furthermore, a groundwater quality suitability map was illustrated by overlaying the groundwater potentiality map with the map showing the potential zones for drinking groundwater in the study area. The results provide significant information and the maps could be used from local authorities for groundwater exploitation and management.

Simulation of boreal Summer Monsoon Rainfall using CFSV2_SSiB model: sensitivity to Land Use Land Cover (LULC)

NASA Astrophysics Data System (ADS)

Chilukoti, N.; Xue, Y.

2016-12-01

The land surface play a vital role in determining the surface energy budget, accurate representation of land use and land cover (LULC) is necessary to improve forecast. In this study, we have investigated the influence of surface vegetation maps with different LULC on simulating the boreal summer monsoon rainfall. Using a National Centres for Environmental Prediction (NCEP) Coupled Forecast System version 2(CFSv2) model coupled with Simplified Simple Biosphere (SSiB) model, two experiments were conducted: one with old vegetation map and one with new vegetation map. The significant differences between new and old vegetation map were in semi-arid and arid areas. For example, in old map Tibetan plateau classified as desert, which is not appropriate, while in new map it was classified as grasslands or shrubs with bare soil. Old map classified the Sahara desert as a bare soil and shrubs with bare soil, whereas in new map it was classified as bare ground. In addition to central Asia and the Sahara desert, in new vegetation map, Europe had more cropped area and India's vegetation cover was changed from crops and forests to wooded grassland and small areas of grassland and shrubs. The simulated surface air temperature with new map shows a significant improvement over Asia, South Africa, and northern America by some 1 to 2ºC and 2 to 3ºC over north east China and these are consistent with the reduced rainfall biases over Africa, near Somali coast, north east India, Bangladesh, east China sea, eastern Pacific and northern USA. Over Indian continent and bay of Bengal dry rainfall anomalies that is the only area showing large dry rainfall bias, however, they were unchanged with new map simulation. Overall the CFSv2(coupled with SSiB) model with new vegetation map show a promising result in improving the monsoon forecast by improving the Land -Atmosphere interactions. To compare with the LULC forcing, experiment was conducted using the Global Forecast System (GFS) simulations forced with different observed Sea Surface Temperatures (SST) for the same period: one is from NCEP reanalysis and one from Hadley Center. They have substantial difference in Indian Ocean. Preliminary analysis shows that, the impact of these two SST data sets on Indian summer monsoon rainfall has no significant impact.

Object-oriented classification of drumlins from digital elevation models

NASA Astrophysics Data System (ADS)

Saha, Kakoli

Drumlins are common elements of glaciated landscapes which are easily identified by their distinct morphometric characteristics including shape, length/width ratio, elongation ratio, and uniform direction. To date, most researchers have mapped drumlins by tracing contours on maps, or through on-screen digitization directly on top of hillshaded digital elevation models (DEMs). This paper seeks to utilize the unique morphometric characteristics of drumlins and investigates automated extraction of the landforms as objects from DEMs by Definiens Developer software (V.7), using the 30 m United States Geological Survey National Elevation Dataset DEM as input. The Chautauqua drumlin field in Pennsylvania and upstate New York, USA was chosen as a study area. As the study area is huge (approximately covers 2500 sq.km. of area), small test areas were selected for initial testing of the method. Individual polygons representing the drumlins were extracted from the elevation data set by automated recognition, using Definiens' Multiresolution Segmentation tool, followed by rule-based classification. Subsequently parameters such as length, width and length-width ratio, perimeter and area were measured automatically. To test the accuracy of the method, a second base map was produced by manual on-screen digitization of drumlins from topographic maps and the same morphometric parameters were extracted from the mapped landforms using Definiens Developer. Statistical comparison showed a high agreement between the two methods confirming that object-oriented classification for extraction of drumlins can be used for mapping these landforms. The proposed method represents an attempt to solve the problem by providing a generalized rule-set for mass extraction of drumlins. To check that the automated extraction process was next applied to a larger area. Results showed that the proposed method is as successful for the bigger area as it was for the smaller test areas.

Landslide susceptibility mapping for a landslide-prone area (Findikli, NE of Turkey) by likelihood-frequency ratio and weighted linear combination models

NASA Astrophysics Data System (ADS)

Akgun, Aykut; Dag, Serhat; Bulut, Fikri

2008-05-01

Landslides are very common natural problems in the Black Sea Region of Turkey due to the steep topography, improper use of land cover and adverse climatic conditions for landslides. In the western part of region, many studies have been carried out especially in the last decade for landslide susceptibility mapping using different evaluation methods such as deterministic approach, landslide distribution, qualitative, statistical and distribution-free analyses. The purpose of this study is to produce landslide susceptibility maps of a landslide-prone area (Findikli district, Rize) located at the eastern part of the Black Sea Region of Turkey by likelihood frequency ratio (LRM) model and weighted linear combination (WLC) model and to compare the results obtained. For this purpose, landslide inventory map of the area were prepared for the years of 1983 and 1995 by detailed field surveys and aerial-photography studies. Slope angle, slope aspect, lithology, distance from drainage lines, distance from roads and the land-cover of the study area are considered as the landslide-conditioning parameters. The differences between the susceptibility maps derived by the LRM and the WLC models are relatively minor when broad-based classifications are taken into account. However, the WLC map showed more details but the other map produced by LRM model produced weak results. The reason for this result is considered to be the fact that the majority of pixels in the LRM map have high values than the WLC-derived susceptibility map. In order to validate the two susceptibility maps, both of them were compared with the landslide inventory map. Although the landslides do not exist in the very high susceptibility class of the both maps, 79% of the landslides fall into the high and very high susceptibility zones of the WLC map while this is 49% for the LRM map. This shows that the WLC model exhibited higher performance than the LRM model.

Status of shallow-aquifer mapping in the Northern Front Range Area, Colorado

USGS Publications Warehouse

Robson, Stanley G.

2001-01-01

Mapping of shallow aquifers in the northern Front Range area of Colorado has been completed as part of the U.S. Geological Survey Front Range Infrastructure Resources Project. The aquifer mapping was undertaken as part of a comprehensive effort to better define the mineral, energy, cartographic, biological, and water resources that are critical to the support and development of the area's infrastructure, such as streets. highways, airports, and buildings. The aquifer mapping was undertaken in cooperation with the Colorado Division of Water Resources and the Colorado Water Conservation Board. The shallow aquifers have been mapped in a 2,450-square-mile area extending as an approximately 30-mile-wide band from north of Fort Collins to the Arapahoe-Douglas County line south of Denver (fig. I). The shallow aquifer mapping in the Denver metropolitan area was published in 1996 as Hydrologic Investigations Atlas HA-736 (Robson. 1996). Shallow aquifer mapping in the Greeley-Nunn area was published as HA-746A (Robson, Arnold, and Heiny, 2000a); mapping in the Fort Collins-Loveland area was published as HA-746B (Robson, Arnold, and Heiny, 2000b); mapping in the Fort Lupton-Gilcrest area was published as HA-746C (Robson, Heiny, and Arnold, 2000c); and mapping in the Boulder-Longmont area was published as HA-746D (Robson, Heiny, and Arnold, 2000d). Each of the five atlases contains five map sheets at 1:50,000 scale showing: 1. The thickness and extent of the unconsolidated sediments (loose gravel. sand. silt, and clay) that overlie the bedrock formations in the area (fig. 2). 2. The altitude and configuration of the bedrock surface. 3. The altitude of the water table and direction of ground-water movement. 4. The saturated thickness of the shallow aquifers. 5. The depth to the water table in the shallow aquifers.

Database and Map of Quaternary Faults and Folds in Peru and its Offshore Region

USGS Publications Warehouse

Machare, Jose; Fenton, Clark H.; Machette, Michael N.; Lavenu, Alain; Costa, Carlos; Dart, Richard L.

2003-01-01

This publication consists of a main map of Quaternary faults and fiolds of Peru, a table of Quaternary fault data, a region inset map showing relative plate motion, and a second inset map of an enlarged area of interest in southern Peru. These maps and data compilation show evidence for activity of Quaternary faults and folds in Peru and its offshore regions of the Pacific Ocean. The maps show the locations, ages, and activity rates of major earthquake-related features such as faults and fault-related folds. These data are accompanied by text databases that describe these features and document current information on their activity in the Quaternary.

Karst in the United States: a digital map compilation and database

USGS Publications Warehouse

Weary, David J.; Doctor, Daniel H.

2014-01-01

This report describes new digital maps delineating areas of the United States, including Puerto Rico and the U.S. Virgin Islands, having karst or the potential for development of karst and pseudokarst. These maps show areas underlain by soluble rocks and also by volcanic rocks, sedimentary deposits, and permafrost that have potential for karst or pseudokarst development. All 50 States contain rocks with potential for karst development, and about 18 percent of their area is underlain by soluble rocks having karst or the potential for development of karst features. The areas of soluble rocks shown are based primarily on selection from State geologic maps of rock units containing significant amounts of carbonate or evaporite minerals. Areas underlain by soluble rocks are further classified by general climate setting, degree of induration, and degree of exposure. Areas having potential for volcanic pseudokarst are those underlain chiefly by basaltic-flow rocks no older than Miocene in age. Areas with potential for pseudokarst features in sedimentary rocks are in relatively unconsolidated rocks from which pseudokarst features, such as piping caves, have been reported. Areas having potential for development of thermokarst features, mapped exclusively in Alaska, contain permafrost in relatively thick surficial deposits containing ground ice. This report includes a GIS database with links from the map unit polygons to online geologic unit descriptions.

Modeled distributions of 12 tree species in New York

Treesearch

Rachel I. Riemann; Barry T. Wilson; Andrew J. Lister; Oren Cook; Sierra Crane-Murdoch

2014-01-01

These maps depict the distribution of 12 tree species across the state of New York. The maps show where these trees do not occur (gray), occasionally occur (pale green), are a minor component (medium green), are a major component (dark green), or are the dominant species (black) in the forest, as determined by that species' total basal area. Basal area is the area...

Exploiting Dragon Envisat Times Series and Other Earth Observation Data

NASA Astrophysics Data System (ADS)

Marie, Tiphanie; Lai, Xijun; Huber, Claire; Chen, Xiaoling; Uribe, Carlos; Huang, Shifeng; Lafaye, Murielle; Yesou, Herve

2010-10-01

Earth Observation data were used for mapping potential Schistosomiasis japonica distribution, within Poyang Lake (Jiangxi Province, PR China). In the first of two steps, areas suitable for the development of Oncomelania hupensis, the intermediate host snail of Schistosoma japonicum, were derived from submersion time parameters and vegetation community indicators. Y early maps from 2003 to 2008 indicate five principally potential endemic areas: Poyang Lake National Nature Reserve, Dalianzi Hu, Gan Delta, Po Jiang and Xi He. Monthly maps showing the annual dynamic of potential O. hupensis presence areas were obtained from December 2005 to December 2008. In a second step human potential transmission risk was handled through the mapping of settlements and the identification of some human activities. The urban areas and settlements were mapped all around the lake and fishing net locations in the central part of Poyang Lake were identified. Finally, data crossing of the different parameters highlight the potential risk of transmission in most of the fishing nets areas.

Mineral mapping in the Maherabad area, eastern Iran, using the HyMap remote sensing data

NASA Astrophysics Data System (ADS)

Molan, Yusuf Eshqi; Refahi, Davood; Tarashti, Ali Hoseinmardi

2014-04-01

This study applies matched filtering on the HyMap airborne hyperspectral data to obtain the distribution map of alteration minerals in the Maherabad area and uses virtual verification to verify the results. This paper also introduces "moving threshold" which tries to find an appropriate threshold value to convert gray scale images, produced by mapping methods, to target and background pixels. The Maherabad area, located in the eastern part of the Lut block, is a Cu-Au porphyry system in which quartz-sericite-pyrite, argillic and propylitic alteration are most common. Minimum noise fraction transform coupled with a pixel purity index was applied on the HyMap images to extract the endmembers of the alteration minerals, including kaolinite, montmorillonite, sericite (muscovite/illite), calcite, chlorite, epidote, and goethite. Since there was no access to any portable spectrometer and/or lab spectral measurements for the verification of the remote sensing imagery results, virtual verification achieved using the USGS spectral library and showed an agreement of 83.19%. The comparison between the results of the matched filtering and X-ray diffraction (XRD) analyses also showed an agreement of 56.13%.

Research on Integrated Mapping——A Case Study of Integrated Land Use with Swamp Mapping

NASA Astrophysics Data System (ADS)

Zhang, S.; Yan, F.; Chang, L.

2015-12-01

Unified real estate registration system shows the attention, determination and effort to of CPC Central Committee and State Council on real estate registration in China. However, under current situation, China's real estate registration work made less progress. One of the reasons is that it's hard to express the property right of real estate on one map under the multi-sector management system. Under current multi-sector management system in China, different departments usually just survey and mapping the land type under its jurisdiction. For example, wetland investigation only mapping all kinds of wetland resources but not mapping other resource types. As a result, it cause he problem of coincidence or leak in integration of different results from different departments. As resources of the earth's surface, the total area of forest, grassland, wetland and so on should be equal to the total area of the earth's surface area. However, under the current system, the area of all kinds of resources is not equal to the sum of the earth's surface. Therefore, it is of great importance to express all the resources on one map. On one hand, this is conducive to find out the real area and distribution of resources and avoid the problem of coincidence or leak in integration; On the other hand, it is helpful to study the dynamic change of different resources. Therefore, we first proposed the "integrated mapping" as a solution, and take integrated land use with swamp mapping in Northeast China as an example to investigate the feasibility and difficulty. Study showed that: integrated land use with swamp mapping can be achieved through combining land use survey standards with swamps survey standards and "second mapping" program. Based on the experience of integrated land use with swamp mapping, we point out its reference function on integrated mapping and unified real estate registration system. We concluded that: (1) Comprehending and integrating different survey standard of different resources is the premise of "integrated mapping", (2) We put forward "multiple code" and "multiple interpretation" scheme in order to solve the problem of "attribute overlap", (3) The area of "attribute overlap" can be segmented by a certain ratio to determine the property right in unified real estate registration.

Looking for an old map

USGS Publications Warehouse

,

1996-01-01

Many people want maps that show an area of the United States as it existed many years ago. These are called historical maps, and there are two types. The most common type consists of special maps prepared by commercial firms to show such historical features as battle-fields, military routes, or the paths taken by famous travelers. Typically, these maps are for sale to tourists at the sites of historical events. The other type is the truly old map--one compiled by a surveyor or cartographer many years ago. Lewis and Clark, for example, made maps of their journeys into the Northwest Territories in 1803-6, and originals of some of these maps still exist.

Potentiometric Surface of the Magothy Aquifer in Southern Maryland, September 2009

USGS Publications Warehouse

Curtin, Stephen E.; Andreasen, David C.; Staley, Andrew W.

2010-01-01

This report presents a map showing the potentiometric surface of the Magothy aquifer in the Magothy Formation of Late Cretaceous age in Southern Maryland during September 2009. The map is based on water-level measurements in 66 wells. The highest measured water level was 85 feet above sea level near the northern boundary and outcrop area of the aquifer in the north-central part of Anne Arundel County. The potentiometric surface declined towards the south. Local hydraulic gradients were directed toward the center of a cone of depression in the Waldorf area that developed in response to pumping. Measured groundwater levels were as low as 71 feet below sea level in the Waldorf area. The map also shows well yield in gallons per day for 2008 at wells or well fields.

Pictorial Atlas of the Netherlands.

ERIC Educational Resources Information Center

Information and Documentation Centre for the Geography of the Netherlands, Utrecht.

The atlas contains almost 40 photographs and 40 maps of geographical aspects of the Netherlands: the coast, dikes, canals, towns, and farmland. Each page contains a photograph, a section of a map showing the area in which the photograph was taken, and a discussion of several paragraphs about the geographical problems of the area and how they have…

Structural map of the summit area of Kilauea Volcano, Hawaii

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1982-01-01

The map shows the faults, sets of fissures, eruptive vent lines and collapse features in the summit area of the volcano. It covers most of the USGS Kilauea Crater 7-1/2 minute quadrangle, together with parts of Volcano, Makaopuhi Crater, and Kau Desert 7-1/2 minute quadrangles. (ACR)

Geologic Map of the Atlin Quadrangle, Southeastern Alaska

USGS Publications Warehouse

Brew, David A.; Himmelberg, Glen R.; Ford, Arthur B.

2009-01-01

This map presents the results of U.S. Geological Survey (USGS) geologic bedrock mapping studies in the mostly glacier covered Atlin 1:250,000-scale quadrangle, northern southeastern Alaska. These studies are part of a long-term systematic effort by the USGS to provide bedrock geologic and mineral-resource information for all of southeastern Alaska, covering all of the Tongass National Forest (including Wilderness Areas) and Glacier Bay National Park and Preserve. Some contributions to this effort are those concerned with southwesternmost part of the region, the Craig and Dixon Entrance quadrangles (Brew, 1994; 1996) and with the Wrangell-Petersburg area (Brew, 1997a-m; Brew and Grybeck, 1997; Brew and Koch, 1997). As shown on the index map (fig. 1), the study area is almost entirely in the northern Coast Mountains adjacent to British Columbia, Canada. No previous geologic map has been published for the area, although Brew and Ford (1985) included a small part of it in a preliminary compilation of the adjoining Juneau quadrangle; and Brew and others (1991a) showed the geology at 1:500,000 scale. Areas mapped nearby in British Columbia and the United States are also shown on figure 1. All of the map area is in the Coast Mountains Complex as defined by Brew and others (1995a). A comprehensive bibliography is available for this and adjacent areas (Brew, 1997n).

Mapping malaria risk using geographic information systems and remote sensing: The case of Bahir Dar City, Ethiopia.

PubMed

Minale, Amare Sewnet; Alemu, Kalkidan

2018-05-07

The main objective of this study was to develop a malaria risk map for Bahir Dar City, Amhara, which is situated south of Lake Tana on the Ethiopian plateau. Rainfall, temperature, altitude, slope and land use/land cover (LULC), as well as proximity measures to lake, river and health facilities, were investigated using remote sensing and geographical information systems. The LULC variable was derived from a 2012 SPOT satellite image by supervised classification, while 30-m spatial resolution measurements of altitude and slope came from the Shuttle Radar Topography Mission. Metrological data were collected from the National Meteorological Agency, Bahir Dar branch. These separate datasets, represented as layers in the computer, were combined using weighted, multi-criteria evaluations. The outcome shows that rainfall, temperature, slope, elevation, distance from the lake and distance from the river influenced the malaria hazard the study area by 35%, 15%, 10%, 7%, 5% and 3%, respectively, resulting in a map showing five areas with different levels of malaria hazard: very high (11.2%); high (14.5%); moderate (63.3%); low (6%); and none (5%). The malaria risk map, based on this hazard map plus additional information on proximity to health facilities and current LULC conditions, shows that Bahir Dar City has areas with very high (15%); high (65%); moderate (8%); and low (5%) levels of malaria risk, with only 2% of the land completely riskfree. Such risk maps are essential for planning, implementing, monitoring and evaluating disease control as well as for contemplating prevention and elimination of epidemiological hazards from endemic areas.

St. Louis Area Earthquake Hazards Mapping Project - A Progress Report-November 2008

USGS Publications Warehouse

Karadeniz, D.; Rogers, J.D.; Williams, R.A.; Cramer, C.H.; Bauer, R.A.; Hoffman, D.; Chung, J.; Hempen, G.L.; Steckel, P.H.; Boyd, O.L.; Watkins, C.M.; McCallister, N.S.; Schweig, E.

2009-01-01

St. Louis has experienced minor earthquake damage at least 12 times in the past 200 years. Because of this history and its proximity to known active earthquake zones, the St. Louis Area Earthquake Hazards Mapping Project (SLAEHMP) is producing digital maps that show variability of earthquake hazards, including liquefaction and ground shaking, in the St. Louis area. The maps will be available free via the internet. Although not site specific enough to indicate the hazard at a house-by-house resolution, they can be customized by the user to show specific areas of interest, such as neighborhoods or transportation routes. Earthquakes currently cannot be predicted, but scientists can estimate how strongly the ground is likely to shake as the result of an earthquake. Earthquake hazard maps provide one way of conveying such estimates. The U.S. Geological Survey (USGS), which produces earthquake hazard maps for the Nation, is working with local partners to develop detailed maps for urban areas vulnerable to strong ground shaking. These partners, which along with the USGS comprise the SLAEHMP, include the Missouri University of Science and Technology-Rolla (Missouri S&T), Missouri Department of Natural Resources (MDNR), Illinois State Geological Survey (ISGS), Saint Louis University, Missouri State Emergency Management Agency, and URS Corporation. Preliminary hazard maps covering a test portion of the 29-quadrangle St. Louis study area have been produced and are currently being evaluated by the SLAEHMP. A USGS Fact Sheet summarizing this project was produced and almost 1000 copies have been distributed at several public outreach meetings and field trips that have featured the SLAEHMP (Williams and others, 2007). In addition, a USGS website focusing on the SLAEHMP, which provides links to project results and relevant earthquake hazard information, can be found at: http://earthquake.usgs.gov/regional/ceus/urban_map/st_louis/index.php. This progress report summarizes the methodology and data used to generate these preliminary maps. For more details about many of the topics in this summary the reader is referred to the Karadeniz (2007) and Chung (2007) Ph.D. theses.

An integrated pan-tropical biomass map using multiple reference datasets.

PubMed

Avitabile, Valerio; Herold, Martin; Heuvelink, Gerard B M; Lewis, Simon L; Phillips, Oliver L; Asner, Gregory P; Armston, John; Ashton, Peter S; Banin, Lindsay; Bayol, Nicolas; Berry, Nicholas J; Boeckx, Pascal; de Jong, Bernardus H J; DeVries, Ben; Girardin, Cecile A J; Kearsley, Elizabeth; Lindsell, Jeremy A; Lopez-Gonzalez, Gabriela; Lucas, Richard; Malhi, Yadvinder; Morel, Alexandra; Mitchard, Edward T A; Nagy, Laszlo; Qie, Lan; Quinones, Marcela J; Ryan, Casey M; Ferry, Slik J W; Sunderland, Terry; Laurin, Gaia Vaglio; Gatti, Roberto Cazzolla; Valentini, Riccardo; Verbeeck, Hans; Wijaya, Arief; Willcock, Simon

2016-04-01

We combined two existing datasets of vegetation aboveground biomass (AGB) (Proceedings of the National Academy of Sciences of the United States of America, 108, 2011, 9899; Nature Climate Change, 2, 2012, 182) into a pan-tropical AGB map at 1-km resolution using an independent reference dataset of field observations and locally calibrated high-resolution biomass maps, harmonized and upscaled to 14 477 1-km AGB estimates. Our data fusion approach uses bias removal and weighted linear averaging that incorporates and spatializes the biomass patterns indicated by the reference data. The method was applied independently in areas (strata) with homogeneous error patterns of the input (Saatchi and Baccini) maps, which were estimated from the reference data and additional covariates. Based on the fused map, we estimated AGB stock for the tropics (23.4 N-23.4 S) of 375 Pg dry mass, 9-18% lower than the Saatchi and Baccini estimates. The fused map also showed differing spatial patterns of AGB over large areas, with higher AGB density in the dense forest areas in the Congo basin, Eastern Amazon and South-East Asia, and lower values in Central America and in most dry vegetation areas of Africa than either of the input maps. The validation exercise, based on 2118 estimates from the reference dataset not used in the fusion process, showed that the fused map had a RMSE 15-21% lower than that of the input maps and, most importantly, nearly unbiased estimates (mean bias 5 Mg dry mass ha(-1) vs. 21 and 28 Mg ha(-1) for the input maps). The fusion method can be applied at any scale including the policy-relevant national level, where it can provide improved biomass estimates by integrating existing regional biomass maps as input maps and additional, country-specific reference datasets. © 2015 John Wiley & Sons Ltd.

Preservation of motor maps with increased motor evoked potential amplitude threshold in RMT determination.

PubMed

Lucente, Giuseppe; Lam, Steven; Schneider, Heike; Picht, Thomas

2018-02-01

Non-invasive pre-surgical mapping of eloquent brain areas with navigated transcranial magnetic stimulation (nTMS) is a useful technique linked to the improvement of surgical planning and patient outcomes. The stimulator output intensity and subsequent resting motor threshold determination (rMT) are based on the motor-evoked potential (MEP) elicited in the target muscle with an amplitude above a predetermined threshold of 50 μV. However, a subset of patients is unable to achieve complete relaxation in the target muscles, resulting in false positives that jeopardize mapping validity with conventional MEP determination protocols. Our aim is to explore the feasibility and reproducibility of a novel mapping approach that investigates how an increase of the MEP amplitude threshold to 300 and 500 μV affects subsequent motor maps. Seven healthy subjects underwent motor mapping with nTMS. RMT was calculated with the conventional methodology in conjunction with experimental 300- and 500-μV MEP amplitude thresholds. Motor mapping was performed with 105% of rMT stimulator intensity using the FDI as the target muscle. Motor mapping was possible in all patients with both the conventional and experimental setups. Motor area maps with a conventional 50-μV threshold showed poor correlation with 300-μV (α = 0.446, p < 0.001) maps, but showed excellent consistency with 500-μV motor area maps (α = 0.974, p < 0.001). MEP latencies were significantly less variable (23 ms for 50 μV vs. 23.7 ms for 300 μV vs. 23.7 ms for 500 μV, p < 0.001). A slight but significant increase of the electric field (EF) value was found (EF: 60.8 V/m vs. 64.8 V/m vs. 66 V/m p < 0.001). Our study demonstrates the feasibility of increasing the MEP detection threshold to 500 μV in rMT determination and motor area mapping with nTMS without losing precision.

Potentiometric surface of the Upper Patapsco aquifer in southern Maryland, September 2009

USGS Publications Warehouse

Curtin, Stephen E.; Andreasen, David C.; Staley, Andrew W.

2010-01-01

This report presents a map showing the potentiometric surface of the upper Patapsco aquifer in the Patapsco Formation of Early Cretaceous age in Southern Maryland during September 2009. The map is based on water-level measurements in 65 wells. The highest measured water level was 118 feet above sea level near the northern boundary and outcrop area of the aquifer in northern Anne Arundel County. From this area, the potentiometric surface declined to the south toward a well field in the Annapolis-Arnold area, and from all directions toward three additional cones of depression. These cones are located in the Waldorf-La Plata area, Chalk Point, and the Leonardtown-Lexington Park area. The lowest measured groundwater levels were 26 feet below sea level at Annapolis, 108 feet below sea level south of Waldorf, 60 feet below sea level at Chalk Point, and 83 feet below sea level at Leonardtown. The map also shows well yield in gallons per day for 2008 at wells or well fields.

Flood inundation map library, Fort Kent, Maine

USGS Publications Warehouse

Lombard, Pamela J.

2012-01-01

Severe flooding occurred in northern Maine from April 28 to May 1, 2008, and damage was extensive in the town of Fort Kent (Lombard, 2010). Aroostook County was declared a Federal disaster area on May 9, 2008. The extent of flooding on both the Fish and St. John Rivers during this event showed that the current Federal Emergency Management Agency (FEMA) Flood Insurance Study (FIS) and Flood Insurance Rate Map (FIRM) (Federal Emergency Management Agency, 1979) were out of date. The U.S. Geological Survey (USGS) conducted a study to develop a flood inundation map library showing the areas and depths for a range of flood stages from bankfull to the flood of record for Fort Kent to complement an updated FIS (Federal Emergency Management Agency, in press). Hydrologic analyses that support the maps include computer models with and without the levee and with various depths of backwater on the Fish River. This fact sheet describes the methods used to develop the maps and describes how the maps can be accessed.

Method for the Preparation of Hazard Map in Urban Area Using Soil Depth and Groundwater Level

NASA Astrophysics Data System (ADS)

Kim, Sung-Wook; Choi, Eun-Kyeong; Cho, Jin Woo; Lee, Ju-Hyoung

2017-04-01

The hazard maps for predicting collapse on natural slopes consists of a combination of topographic, hydrological, and geological factors. Topographic factors are extracted from DEM, including aspect, slope, curvature, and topographic index. Hydrological factors, such as distance to drainage, drainage density, stream-power index, and wetness index are most important factors for slope instability. However, most of the urban areas are located on the plains and it is difficult to apply the hazard map using the topography and hydrological factors. In order to evaluate the risk of collapse of flat and low slope areas, soil depth and groundwater level data were collected and used as a factor for interpretation. In addition, the reliability of the hazard map was compared with the disaster history of the study area (Gangnam-gu and Yeouido district). In the disaster map of the disaster prevention agency, the urban area was mostly classified as the stable area and did not reflect the collapse history. Soil depth, drainage conditions and groundwater level obtained from boreholes were added as input data of hazard map, and disaster vulnerability increased at the location where the actual collapse points. In the study area where damage occurred, the moderate and low grades of the vulnerability of previous hazard map were 12% and 88%, respectively. While, the improved map showed 2% high grade, moderate grade 29%, low grade 66% and very low grade 2%. These results were similar to actual damage. Keywords: hazard map, urban area, soil depth, ground water level Acknowledgement This research was supported by a Grant from a Strategic Research Project (Horizontal Drilling and Stabilization Technologies for Urban Search and Rescue (US&R) Operation) funded by the Korea Institute of Civil Engineering and Building Technology.

Geochemical map of the Rattlesnake Roadless Area, Coconino and Yavapai counties, Arizona

USGS Publications Warehouse

Gerstel, W.J.

1985-01-01

The geochemical survey of the Rattlesnake Roadless Area was conducted in May 1982 by the U.S. Geological Survey to aid in a mineral resource appraisal of the area. A total of 114 stream-sediment samples, 68 heavy-mineral concentrates from stream sediment, 20 rock samples, and 4 water samples was collected by S.C. Rose, D.E. Hendzel, and W.J. Gerstel, with helicopter support from Jack Ruby, pilot for Helicopters Unlimited. All sample localities are plotted on the map; sample localities showing anomalous barium and lead are also indicated on the map.

Age mapping and dating of monazite on the electron microprobe: Deconvoluting multistage tectonic histories

NASA Astrophysics Data System (ADS)

Williams, Michael L.; Jercinovic, Michael J.; Terry, Michael P.

1999-11-01

High-resolution X-ray mapping and dating of monazite on the electron microprobe are powerful geochronological tools for structural, metamorphic, and tectonic analysis. X-ray maps commonly show complex Th, U, and Pb zoning that reflects monazite growth and overgrowth events. Age maps constructed from the X-ray maps simplify the zoning and highlight age domains. Microprobe dating offers a rapid, in situ method for estimating ages of mapped domains. Application of these techniques has placed new constraints on the tectonic history of three areas. In western Canada, age mapping has revealed multiphase monazite, with older cores and younger rims, included in syntectonic garnet. Microprobe ages show that tectonism occurred ca. 1.9 Ga, 700 m.y. later than mylonitization in the adjacent Snowbird tectonic zone. In New Mexico, age mapping and dating show that the dominant fabric and triple-point metamorphism occurred during a 1.4 Ga reactivation, not during the 1.7 Ga Yavapai-Mazatzal orogeny. In Norway, monazite inclusions in garnet constrain high-pressure metamorphism to ca. 405 Ma, and older cores indicate a previously unrecognized component of ca. 1.0 Ga monazite. In all three areas, microprobe dating and age mapping have provided a critical textural context for geochronologic data and a better understanding of the complex age spectra of these multistage orogenic belts.

32 CFR 644.42 - Appraisal report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... designed, dates of original construction and/or additions; include, for privately owned property, a ten... to show how they indicate the value of the land being appraised. 13. VALUE ESTIMATE BY COMPARATIVE... MAP. (Within the city or area) 19. COMPARATIVE MAP DATA. Show geographic location of the appraised...

32 CFR 644.42 - Appraisal report.

Code of Federal Regulations, 2010 CFR

2010-07-01

... designed, dates of original construction and/or additions; include, for privately owned property, a ten... to show how they indicate the value of the land being appraised. 13. VALUE ESTIMATE BY COMPARATIVE... MAP. (Within the city or area) 19. COMPARATIVE MAP DATA. Show geographic location of the appraised...

32 CFR 644.42 - Appraisal report.

Code of Federal Regulations, 2014 CFR

2014-07-01

... designed, dates of original construction and/or additions; include, for privately owned property, a ten... to show how they indicate the value of the land being appraised. 13. VALUE ESTIMATE BY COMPARATIVE... MAP. (Within the city or area) 19. COMPARATIVE MAP DATA. Show geographic location of the appraised...

32 CFR 644.42 - Appraisal report.

Code of Federal Regulations, 2011 CFR

2011-07-01

... designed, dates of original construction and/or additions; include, for privately owned property, a ten... to show how they indicate the value of the land being appraised. 13. VALUE ESTIMATE BY COMPARATIVE... MAP. (Within the city or area) 19. COMPARATIVE MAP DATA. Show geographic location of the appraised...

32 CFR 644.42 - Appraisal report.

Code of Federal Regulations, 2012 CFR

2012-07-01

... designed, dates of original construction and/or additions; include, for privately owned property, a ten... to show how they indicate the value of the land being appraised. 13. VALUE ESTIMATE BY COMPARATIVE... MAP. (Within the city or area) 19. COMPARATIVE MAP DATA. Show geographic location of the appraised...

Prediction of Exploration Target Areas for GEM Deposits in Mogok Stone Tract, Northern Myanmar by Integrating Remote Sensing and Geoscience Data

NASA Astrophysics Data System (ADS)

Oo, Tin Ko

2011-07-01

The Mogok Stone Tract area has long been known for world famous finest ruby since 1597. The Mogok area lies in northern Myanmar and is located at about 205.99km northeast from Mandalay, the second largest city of Myanmar. The Mogok Group of metasedimentary rocks is divided into four units: (1) Wabyudaung Marble, (2) Ayenyeinchantha Calc-silicate, (3) Gwebin Quartzite, and (4) Kabe Gneiss. Igneous rocks in the Mogok area are classified into two units: (1) Kabaing Granite and (2) Pingutaung Leucogranite. The Mogok area has a complex structure involving several folds and faults. Using marbles and calc-silicates as marker horizons, a series of anticline and syncline can be identified such as Mogok syncline, Ongaing anticline, Bawpadan syncline, and Kyatpyin anticline. All the foldings show a low-angle plunge to the south. The main precious stones of the Mogok area are ruby and sapphire; and the other important semi-precious stones are spinel, topaz, peridot, garnet, apatite, beryl, tourmaline (rubellite), quartz, diopside, fluorite, and enstatite. Geological and remote sensing data are processed to extract the indicative features of gem mineralized areas: lithology, structure, and hydrothermal alteration. Density slice version of Landsat ETM band ratios 5/7 is used to map clay alterations. Filtering Landsat ETM band 5 by using edge detection filter is applied for lineament mapping. Spatial integration of various geoscience and remote sensing data sets such as geological maps, Landsat ETM images, and the location map of gem mines show the distribution of alteration zones associated with the gem mineralization in the study area. Geographic Information System (GIS) model has been designed and implemented by ARCVIEW software package based on the overlay of lithologic, lineament, and alteration vector maps. This process has resulted in delineation of most promising areas of probable gem mineralized zones as on the output map.

Correlation-based perfusion mapping using time-resolved MR angiography: A feasibility study for patients with suspicions of steno-occlusive craniocervical arteries.

PubMed

Nam, Yoonho; Jang, Jinhee; Park, Sonya Youngju; Choi, Hyun Seok; Jung, So-Lyung; Ahn, Kook-Jin; Kim, Bum-Soo

2018-05-22

To explore the feasibility of using correlation-based time-delay (CTD) maps produced from time-resolved MR angiography (TRMRA) to diagnose perfusion abnormalities in patients suspected to have steno-occlusive lesions in the craniocervical arteries. Twenty-seven patients who were suspected to have steno-occlusive lesions in the craniocervical arteries underwent both TRMRA and brain single-photon emission computed tomography (SPECT). TRMRA was performed on the supra-aortic area after intravenous injection of a 0.03 mmol/kg gadolinium-based contrast agent. Time-to-peak (TTP) maps and CTD maps of the brain were automatically generated from TRMRA data, and their quality was assessed. Detection of perfusion abnormalities was compared between CTD maps and the time-series maximal intensity projection (MIP) images from TRMRA and TTP maps. Correlation coefficients between quantitative changes in SPECT and parametric maps for the abnormal perfusion areas were calculated. The CTD maps were of significantly superior quality than TTP maps (p < 0.01). For perfusion abnormality detection, CTD maps (kappa 0.84, 95% confidence interval [CI] 0.67-1.00) showed better agreement with SPECT than TTP maps (0.66, 0.46-0.85). For perfusion deficit detection, CTD maps showed higher accuracy (85.2%, 95% CI 66.3-95.8) than MIP images (66.7%, 46-83.5), with marginal significance (p = 0.07). In abnormal perfusion areas, correlation coefficients between SPECT and CTD (r = 0.74, 95% CI 0.34-0.91) were higher than those between SPECT and TTP (r = 0.66, 0.20-0.88). CTD maps generated from TRMRA were of high quality and offered good diagnostic performance for detecting perfusion abnormalities associated with steno-occlusive arterial lesions in the craniocervical area. • Generation of perfusion parametric maps from time-resolved MR angiography is clinically useful. • Correlation-based delay maps can be used to detect perfusion abnormalities associated with steno-occlusive craniocervical arteries. • Estimation of correlation-based delay is robust for low signal-to-noise 4D MR data.

Time Series Analysis OF SAR Image Fractal Maps: The Somma-Vesuvio Volcanic Complex Case Study

NASA Astrophysics Data System (ADS)

Pepe, Antonio; De Luca, Claudio; Di Martino, Gerardo; Iodice, Antonio; Manzo, Mariarosaria; Pepe, Susi; Riccio, Daniele; Ruello, Giuseppe; Sansosti, Eugenio; Zinno, Ivana

2016-04-01

The fractal dimension is a significant geophysical parameter describing natural surfaces representing the distribution of the roughness over different spatial scale; in case of volcanic structures, it has been related to the specific nature of materials and to the effects of active geodynamic processes. In this work, we present the analysis of the temporal behavior of the fractal dimension estimates generated from multi-pass SAR images relevant to the Somma-Vesuvio volcanic complex (South Italy). To this aim, we consider a Cosmo-SkyMed data-set of 42 stripmap images acquired from ascending orbits between October 2009 and December 2012. Starting from these images, we generate a three-dimensional stack composed by the corresponding fractal maps (ordered according to the acquisition dates), after a proper co-registration. The time-series of the pixel-by-pixel estimated fractal dimension values show that, over invariant natural areas, the fractal dimension values do not reveal significant changes; on the contrary, over urban areas, it correctly assumes values outside the natural surfaces fractality range and show strong fluctuations. As a final result of our analysis, we generate a fractal map that includes only the areas where the fractal dimension is considered reliable and stable (i.e., whose standard deviation computed over the time series is reasonably small). The so-obtained fractal dimension map is then used to identify areas that are homogeneous from a fractal viewpoint. Indeed, the analysis of this map reveals the presence of two distinctive landscape units corresponding to the Mt. Vesuvio and Gran Cono. The comparison with the (simplified) geological map clearly shows the presence in these two areas of volcanic products of different age. The presented fractal dimension map analysis demonstrates the ability to get a figure about the evolution degree of the monitored volcanic edifice and can be profitably extended in the future to other volcanic systems with very distinctive characteristics, with the aim to perform land classification, such as the identification of areas characterized by similar soil use, slopes and exposures.

Volcanic hazard management in dispersed volcanism areas

NASA Astrophysics Data System (ADS)

Marrero, Jose Manuel; Garcia, Alicia; Ortiz, Ramon

2014-05-01

Traditional volcanic hazard methodologies were developed mainly to deal with the big stratovolcanoes. In such type of volcanoes, the hazard map is an important tool for decision-makers not only during a volcanic crisis but also for territorial planning. According to the past and recent eruptions of a volcano, all possible volcanic hazards are modelled and included in the hazard map. Combining the hazard map with the Event Tree the impact area can be zoned and defining the likely eruptive scenarios that will be used during a real volcanic crisis. But in areas of disperse volcanism is very complex to apply the same volcanic hazard methodologies. The event tree do not take into account unknown vents, because the spatial concepts included in it are only related with the distance reached by volcanic hazards. The volcanic hazard simulation is also difficult because the vent scatter modifies the results. The volcanic susceptibility try to solve this problem, calculating the most likely areas to have an eruption, but the differences between low and large values obtained are often very small. In these conditions the traditional hazard map effectiveness could be questioned, making necessary a change in the concept of hazard map. Instead to delimit the potential impact areas, the hazard map should show the expected behaviour of the volcanic activity and how the differences in the landscape and internal geo-structures could condition such behaviour. This approach has been carried out in La Palma (Canary Islands), combining the concept of long-term hazard map with the short-term volcanic scenario to show the expected volcanic activity behaviour. The objective is the decision-makers understand how a volcanic crisis could be and what kind of mitigation measurement and strategy could be used.

DEVELOPMENT OF A RADON PROTECTION MAP FOR LARGE BUILDINGS IN FLORIDA

EPA Science Inventory

The report discusses the development of a radon protection map to show from soil and geological features the areas of Florida that require different levels of Radon protection for large building construction. The map was proposed as a basis for implementing radon-protective const...

A new catalog of planetary maps

NASA Technical Reports Server (NTRS)

Batson, R. M.; Inge, J. L.

1991-01-01

A single, concise reference to all existing planetary maps, including lunar ones, is being prepared that will allow map users to identify and locate maps of their areas of interest. This will be the first such comprehensive listing of planetary maps. Although the USGS shows index maps on the collar of each map sheet, periodically publishes index maps of Mars, and provides informal listings of the USGS map database, no tabulation exists that identifies all planetary maps, including those published by DMA and other organizations. The catalog will consist of a booklet containing small-scale image maps with superimposed quadrangle boundaries and map data tabulations.

Application of laboratory reflectance spectroscopy to target and map expansive soils: example of the western Loiret, France

NASA Astrophysics Data System (ADS)

Hohmann, Audrey; Dufréchou, Grégory; Grandjean, Gilles; Bourguignon, Anne

2014-05-01

Swelling soils contain clay minerals that change volume with water content and cause extensive and expensive damage on infrastructures. Based on spatial distribution of infrastructure damages and existing geological maps, the Bureau de Recherches Géologiques et Minières (BRGM, i.e. the French Geological Survey) published in 2010 a 1:50 000 swelling hazard map of France, indexing the territory to low, moderate, or high swelling risk. This study aims to use SWIR (1100-2500 nm) reflectance spectra of soils acquired under laboratory controlled conditions to estimate the swelling potential of soils and improve the swelling risk map of France. 332 samples were collected at the W of Orléans (France) in various geological formations and swelling risk areas. Comparisons of swelling potential of soil samples and swelling risk areas of the map show several inconsistent associations that confirm the necessity to redraw the actual swelling risk map of France. New swelling risk maps of the sampling area were produce from soil samples using three interpolation methods. Maps produce using kriging and Natural neighbour interpolation methods did not permit to show discrete lithological units, introduced unsupported swelling risk zones, and did not appear useful to refine swelling risk map of France. Voronoi polygon was also used to produce map where swelling potential estimated from each samples were extrapolated to a polygon and all polygons were thus supported by field information. From methods tested here, Voronoi polygon appears thus the most adapted method to produce expansive soils maps. However, size of polygon is highly dependent of the samples spacing and samples may not be representative of the entire polygon. More samples are thus needed to provide reliable map at the scale of the sampling area. Soils were also sampled along two sections with a sampling interval of ca. 260 m and ca. 50 m. Sample interval of 50 m appears more adapted for mapping of smallest lithological units. The presence of several samples close to themselves indicating the same swelling potential is a good indication of the presence of a zone with constant swelling potential. Combination of Voronoi method and sampling interval of ca. 50 m appear adapted to produce local swelling potential maps in areas where doubt remain or where infrastructure damages attributed to expansive soils are knew.

Diagnostic classification of macular ganglion cell and retinal nerve fiber layer analysis: differentiation of false-positives from glaucoma.

PubMed

Kim, Ko Eun; Jeoung, Jin Wook; Park, Ki Ho; Kim, Dong Myung; Kim, Seok Hwan

2015-03-01

To investigate the rate and associated factors of false-positive diagnostic classification of ganglion cell analysis (GCA) and retinal nerve fiber layer (RNFL) maps, and characteristic false-positive patterns on optical coherence tomography (OCT) deviation maps. Prospective, cross-sectional study. A total of 104 healthy eyes of 104 normal participants. All participants underwent peripapillary and macular spectral-domain (Cirrus-HD, Carl Zeiss Meditec Inc, Dublin, CA) OCT scans. False-positive diagnostic classification was defined as yellow or red color-coded areas for GCA and RNFL maps. Univariate and multivariate logistic regression analyses were used to determine associated factors. Eyes with abnormal OCT deviation maps were categorized on the basis of the shape and location of abnormal color-coded area. Differences in clinical characteristics among the subgroups were compared. (1) The rate and associated factors of false-positive OCT maps; (2) patterns of false-positive, color-coded areas on the GCA deviation map and associated clinical characteristics. Of the 104 healthy eyes, 42 (40.4%) and 32 (30.8%) showed abnormal diagnostic classifications on any of the GCA and RNFL maps, respectively. Multivariate analysis revealed that false-positive GCA diagnostic classification was associated with longer axial length and larger fovea-disc angle, whereas longer axial length and smaller disc area were associated with abnormal RNFL maps. Eyes with abnormal GCA deviation map were categorized as group A (donut-shaped round area around the inner annulus), group B (island-like isolated area), and group C (diffuse, circular area with an irregular inner margin in either). The axial length showed a significant increasing trend from group A to C (P=0.001), and likewise, the refractive error was more myopic in group C than in groups A (P=0.015) and B (P=0.014). Group C had thinner average ganglion cell-inner plexiform layer thickness compared with other groups (group A=B>C, P=0.004). Abnormal OCT diagnostic classification should be interpreted with caution, especially in eyes with long axial lengths, large fovea-disc angles, and small optic discs. Our findings suggest that the characteristic patterns of OCT deviation map can provide useful clues to distinguish glaucomatous changes from false-positive findings. Copyright © 2015 American Academy of Ophthalmology. Published by Elsevier Inc. All rights reserved.

Clinical Impact and Implication of Real-Time Oscillation Analysis for Language Mapping.

PubMed

Ogawa, Hiroshi; Kamada, Kyousuke; Kapeller, Christoph; Prueckl, Robert; Takeuchi, Fumiya; Hiroshima, Satoru; Anei, Ryogo; Guger, Christoph

2017-01-01

We developed a functional brain analysis system that enabled us to perform real-time task-related electrocorticography (ECoG) and evaluated its potential in clinical practice. We hypothesized that high gamma activity (HGA) mapping would provide better spatial and temporal resolution with high signal-to-noise ratios. Seven awake craniotomy patients were evaluated. ECoG was recorded during language tasks using subdural grids, and HGA (60-170 Hz) maps were obtained in real time. The patients also underwent electrocortical stimulation (ECS) mapping to validate the suspected functional locations on HGA mapping. The results were compared and calculated to assess the sensitivity and specificity of HGA mapping. For reference, bedside HGA-ECS mapping was performed in 5 epilepsy patients. HGA mapping demonstrated functional brain areas in real time and was comparable with ECS mapping. Sensitivity and specificity for the language area were 90.1% ± 11.2% and 90.0% ± 4.2%, respectively. Most HGA-positive areas were consistent with ECS-positive regions in both groups, and there were no statistical between-group differences. Although this study included a small number of subjects, it showed real-time HGA mapping with the same setting and tasks under different conditions. This study demonstrates the clinical feasibility of real-time HGA mapping. Real-time HGA mapping enabled simple and rapid detection of language functional areas in awake craniotomy. The mapping results were highly accurate, although the mapping environment was noisy. Further studies of HGA mapping may provide the potential to elaborate complex brain functions and networks. Copyright © 2016 Elsevier Inc. All rights reserved.

Map Showing Quaternary Geology and Geomorphology of the Granite Park Area, Grand Canyon, Arizona

USGS Publications Warehouse

Hereford, Richard; Burke, Kelly J.; Thompson, Kathryn S.

2000-01-01

View to west-northwest showing map area and setting of Granite Park; Grand Canyon, Arizona. The Colorado River flows from right to left. Granite Park Wash is the light-colored area in foreground of photograph. The debris fan of 209 Mile Canyon is at left center. Pleistocene gravel is exposed in the steep, light-colored bank above 209 Mile Rapids at left edge of photograph. The black-colored ledge that forms the dark cliff at upper right of photograph is the basalt flow of Hamblin (1994). Sand dunes, debris fans, and terraces of the Colorado River cover the lower half of this area shown in this photograph.

Mapping the seafloor geology offshore of Massachusetts

USGS Publications Warehouse

Barnhardt, Walter A.; Andrews, Brian D.

2006-01-01

Geologic and bathymetric maps help us understand the evolutionary history of the Massachusetts coast and the processes that have shaped it. The maps show the distribution of bottom types (for example, bedrock, gravel, sand, mud) and water depths over large areas of the seafloor. In turn, these two fundamental parameters largely determine the species of flora and fauna that inhabit a particular area. Knowledge of bottom types and water depths provides a framework for mapping benthic habitats and managing marine resources. The need for coastal–zone mapping to inform policy and management is widely recognized as critical for mitigating hazards, creating resource inventories, and tracking environmental changes (National Research Council, 2004; U.S. Commission on Ocean Policy, 2004).

Seismotectonic Map of Afghanistan and Adjacent Areas

USGS Publications Warehouse

Wheeler, Russell L.; Rukstales, Kenneth S.

2007-01-01

Introduction This map is part of an assessment of Afghanistan's geology, natural resources, and natural hazards. One of the natural hazards is from earthquake shaking. One of the tools required to address the shaking hazard is a probabilistic seismic-hazard map, which was made separately. The information on this seismotectonic map has been used in the design and computation of the hazard map. A seismotectonic map like this one shows geological, seismological, and other information that previously had been scattered among many sources. The compilation can show spatial relations that might not have been seen by comparing the original sources, and it can suggest hypotheses that might not have occurred to persons who studied those scattered sources. The main map shows faults and earthquakes of Afghanistan. Plate convergence drives the deformations that cause the earthquakes. Accordingly, smaller maps and text explain the modern plate-tectonic setting of Afghanistan and its evolution, and relate both to patterns of faults and earthquakes.

Surficial geologic map of the greater Omaha area, Nebraska and Iowa

USGS Publications Warehouse

Shroba, R.R.; Brandt, T.R.; Blossom, J.C.

2001-01-01

Geologic mapping, in support of the USGS Omaha-Kansas City Geologic Mapping Project, shows the spatial distribution of artificial-fill, alluvial, eolian, and glacial deposits and bedrock in and near Omaha, Nebraska. Artificial fill deposits are mapped chiefly beneath commercial structures, segments of interstate highways and other major highways, railroad tracks, airport runways, and military facilities, and in landfills and earth fills. Alluvial deposits are mapped beneath flood plains, in stream terraces, and on hill slopes. They include flood-plain and stream-channel alluvium, sheetwash alluvium, and undivided sheetwash alluvium and stream alluvium. Wind-deposited loess forms sheets that mantle inter-stream areas and late Wisconsin terrace alluvium. Peoria Loess is younger of the two loess sheets and covers much of the inter-stream area in the map area. Loveland Loess is older and is exposed in a few small areas in the eastern part of the map area. Glacial deposits are chiefly heterogeneous, ice-deposited, clayey material (till) and minor interstratified stream-deposited sand and gravel. Except for small outcrops, glacial deposits are covered by eolian and alluvial deposits throughout most of the map area. Bedrock is locally exposed in natural exposures along the major streams and in quarries. It consists of Dakota Sandstone and chiefly limestone and shale of the Lansing and Kansas City Groups. Sand and gravel in flood plain and stream-channel alluvium in the Platte River valley are used mainly for concrete aggregate. Limestone of the Lansing and Kansas City Groups is used for road-surfacing material, rip rap, and fill material.

Geologic Map of the Central Marysvale Volcanic Field, Southwestern Utah

USGS Publications Warehouse

Rowley, Peter D.; Cunningham, Charles G.; Steven, Thomas A.; Workman, Jeremiah B.; Anderson, John J.; Theissen, Kevin M.

2002-01-01

The geologic map of the central Marysvale volcanic field, southwestern Utah, shows the geology at 1:100,000 scale of the heart of one of the largest Cenozoic volcanic fields in the Western United States. The map shows the area of 38 degrees 15' to 38 degrees 42'30' N., and 112 degrees to 112 degrees 37'30' W. The Marysvale field occurs mostly in the High Plateaus, a subprovince of the Colorado Plateau and structurally a transition zone between the complexly deformed Great Basin to the west and the stable, little-deformed main part of the Colorado Plateau to the east. The western part of the field is in the Great Basin proper. The volcanic rocks and their source intrusions in the volcanic field range in age from about 31 Ma (Oligocene) to about 0.5 Ma (Pleistocene). These rocks overlie sedimentary rocks exposed in the mapped area that range in age from Ordovician to early Cenozoic. The area has been deformed by thrust faults and folds formed during the late Mesozoic to early Cenozoic Sevier deformational event, and later by mostly normal faults and folds of the Miocene to Quaternary basin-range episode. The map revises and updates knowledge gained during a long-term U.S. Geological Survey investigation of the volcanic field, done in part because of its extensive history of mining. The investigation also was done to provide framework geologic knowledge suitable for defining geologic and hydrologic hazards, for locating hydrologic and mineral resources, and for an understanding of geologic processes in the area. A previous geologic map (Cunningham and others, 1983, U.S. Geological Survey Miscellaneous Investigations Series I-1430-A) covered the same area as this map but was published at 1:50,000 scale and is obsolete due to new data. This new geologic map of the central Marysvale field, here published as U.S. Geological Survey Geologic Investigations Series I-2645-A, is accompanied by gravity and aeromagnetic maps of the same area and the same scale (Campbell and others, 1999, U.S. Geological Survey Geologic Investigations Series I-2645-B).

Assessment of the spatial extent and height of flooding in Lake Champlain during May 2011, using satellite remote sensing and ground-based information

USGS Publications Warehouse

Bjerklie, David M.; Trombley, Thomas J.; Olson, Scott A.

2014-01-01

Landsat 5 and moderate resolution imaging spectro-radiometer satellite imagery were used to map the area of inundation of Lake Champlain, which forms part of the border between New York and Vermont, during May 2011. During this month, the lake’s water levels were record high values not observed in the previous 150 years. Lake inundation area determined from the satellite imagery is correlated with lake stage measured at three U.S. Geological Survey lake level gages to provide estimates of lake area at different lake levels (stage/area rating) and also compared with the levels of the high-water marks (HWMs) located on the Vermont side of the lake. The rating developed from the imagery shows a somewhat different relation than a similar stage/area rating developed from a medium-resolution digital elevation model (DEM) of the region. According to the rating derived from the imagery, the lake surface area during the peak lake level increased by about 17 percent above the average or “normal” lake level. By using a comparable rating developed from the DEM, the increase above average is estimated to be about 12 percent. The northern part of the lake (north of Burlington) showed the largest amount of flooding. Based on intersecting the inundation maps with the medium-resolution DEM, lake levels were not uniform around the lake. This is also evident from the lake level gage measurements and HWMs. The gage data indicate differences up to 0.5 feet between the northern and southern end of the lake. Additionally, the gage data show day-to-day and intradaily variation of the same range (0.5 foot). The high-water mark observations show differences up to 2 feet around the lake, with the highest level generally along the south- and west-facing shorelines. The data suggest that during most of May 2011, water levels were slightly higher and less variable in the northern part of the lake. These phenomena may be caused by wind effects as well as proximity to major river inputs to the lake. The inundation areas generated from the imagery generally coincide with flood mapping as estimated by the Federal Emergency Management Agency (FEMA) and shown on its digital flood insurance rate maps. Where areas in the flood inundation map derived from the imagery and the FEMA estimated flooded areas differ substantially, this difference may be due to differences between the flood magnitude at the time of the image and the assumed flood condition used for the FEMA modeling and mapping, wind/storage effects not accounted for by the FEMA modeling, and the resolution of the image compared to the DEM used in the FEMA mapping.

43 CFR 3592.1 - Operating plans.

Code of Federal Regulations, 2014 CFR

2014-10-01

... OPERATIONS Plans and Maps § 3592.1 Operating plans. (a) Before conducting any operations under any lease(s... description of geologic conditions and mineral resources, with appropriate maps, within the area where mining is to be conducted; (3) A copy of a suitable map or aerial photograph showing the topography, the...

43 CFR 3592.1 - Operating plans.

Code of Federal Regulations, 2013 CFR

2013-10-01

... OPERATIONS Plans and Maps § 3592.1 Operating plans. (a) Before conducting any operations under any lease(s... description of geologic conditions and mineral resources, with appropriate maps, within the area where mining is to be conducted; (3) A copy of a suitable map or aerial photograph showing the topography, the...

43 CFR 3592.1 - Operating plans.

Code of Federal Regulations, 2012 CFR

2012-10-01

... OPERATIONS Plans and Maps § 3592.1 Operating plans. (a) Before conducting any operations under any lease(s... description of geologic conditions and mineral resources, with appropriate maps, within the area where mining is to be conducted; (3) A copy of a suitable map or aerial photograph showing the topography, the...

Geomorphology applied to landscape analysis for planning and management of natural spaces. Case study: Las Batuecas-S. de Francia and Quilamas natural parks, (Salamanca, Spain).

PubMed

Martínez-Graña, A M; Silva, P G; Goy, J L; Elez, J; Valdés, V; Zazo, C

2017-04-15

Geomorphology is fundamental to landscape analysis, as it represents the main parameter that determines the land spatial configuration and facilitates reliefs classification. The goal of this article is the elaboration of thematic maps that enable the determination of different landscape units and elaboration of quality and vulnerability synthetic maps for landscape fragility assessment prior to planning human activities. For two natural spaces, the final synthetic maps were created with direct (visual-perceptual features) and indirect (cartographic models and 3D simulations) methods from thematic maps with GIS technique. This enabled the creation of intrinsic and extrinsic landscape quality maps showing sectors needing most preservation, as well as intrinsic and extrinsic landscape fragility maps (environment response capacity or vulnerability towards human actions). The resulting map shows absorption capacity for areas of maximum and/or minimum human intervention. Sectors of high absorption capacity (minimum need for preservation) are found where the incidence of human intervention is minimum: escarpment bottoms, fitted rivers, sinuous high lands with thick vegetation coverage and valley interiors, or those areas with high landscape quality, low fragility and high absorption capacity, whose average values are found across lower hillsides of some valleys, and sectors with low absorption capacity (areas needing most preservation) found mainly in the inner parts of natural spaces: peaks and upper hillsides, synclines flanks and scattered areas. For the integral analysis of landscape, a mapping methodology has been set. It comprises a valid criterion for rational and sustainable planning, management and protection of natural spaces. Copyright © 2017 Elsevier B.V. All rights reserved.

Mapping Weathering and Alteration Minerals in the Comstock and Geiger Grade Areas using Visible to Thermal Infrared Airborne Remote Sensing Data

NASA Technical Reports Server (NTRS)

Vaughan, Greg R.; Calvin, Wendy M.

2005-01-01

To support research into both precious metal exploration and environmental site characterization a combination of high spatial/spectral resolution airborne visible, near infrared, short wave infrared (VNIR/SWIR) and thermal infrared (TIR) image data were acquired to remotely map hydrothermal alteration minerals around the Geiger Grade and Comstock alteration regions, and map the mineral by-products of weathered mine dumps in Virginia City. Remote sensing data from the Airborne Visible Infrared Imaging Spectrometer (AVIRIS), SpecTIR Corporation's airborne hyperspectral imager (HyperSpecTIR), the MODIS-ASTER airborne simulator (MASTER), and the Spatially Enhanced Broadband Array Spectrograph System (SEBASS) were acquired and processed into mineral maps based on the unique spectral signatures of image pixels. VNIR/SWIR and TIR field spectrometer data were collected for both calibration and validation of the remote data sets, and field sampling, laboratory spectral analyses and XRD analyses were made to corroborate the surface mineralogy identified by spectroscopy. The resulting mineral maps show the spatial distribution of several important alteration minerals around each study area including alunite, quartz, pyrophyllite, kaolinite, montmorillonite/muscovite, and chlorite. In the Comstock region the mineral maps show acid-sulfate alteration, widespread propylitic alteration and extensive faulting that offsets the acid-sulfate areas, in contrast to the larger, dominantly acid-sulfate alteration exposed along Geiger Grade. Also, different mineral zones within the intense acid-sulfate areas were mapped. In the Virginia City historic mining district the important weathering minerals mapped include hematite, goethite, jarosite and hydrous sulfate minerals (hexahydrite, alunogen and gypsum) located on mine dumps. Sulfate minerals indicate acidic water forming in the mine dump environment. While there is not an immediate threat to the community, there are clearly sources of acidic drainage that were identified remotely.

Mapping landslide source and transport areas in VHR images with Object-Based Analysis and Support Vector Machines

NASA Astrophysics Data System (ADS)

Heleno, Sandra; Matias, Magda; Pina, Pedro

2015-04-01

Visual interpretation of satellite imagery remains extremely demanding in terms of resources and time, especially when dealing with numerous multi-scale landslides affecting wide areas, such as is the case of rainfall-induced shallow landslides. Applying automated methods can contribute to more efficient landslide mapping and updating of existing inventories, and in recent years the number and variety of approaches is rapidly increasing. Very High Resolution (VHR) images, acquired by space-borne sensors with sub-metric precision, such as Ikonos, Quickbird, Geoeye and Worldview, are increasingly being considered as the best option for landslide mapping, but these new levels of spatial detail also present new challenges to state of the art image analysis tools, asking for automated methods specifically suited to map landslide events on VHR optical images. In this work we develop and test a methodology for semi-automatic landslide recognition and mapping of landslide source and transport areas. The method combines object-based image analysis and a Support Vector Machine supervised learning algorithm, and was tested using a GeoEye-1 multispectral image, sensed 3 days after a damaging landslide event in Madeira Island, together with a pre-event LiDAR DEM. Our approach has proved successful in the recognition of landslides on a 15 Km2-wide study area, with 81 out of 85 landslides detected in its validation regions. The classifier also showed reasonable performance (false positive rate 60% and false positive rate below 36% in both validation regions) in the internal mapping of landslide source and transport areas, in particular in the sunnier east-facing slopes. In the less illuminated areas the classifier is still able to accurately map the source areas, but performs poorly in the mapping of landslide transport areas.

Bedrock geologic map of the northern Alaska Peninsula area, southwestern Alaska

USGS Publications Warehouse

Wilson, Frederic H.; Blodgett, Robert B.; Blome, Charles D.; Mohadjer, Solmaz; Preller, Cindi C.; Klimasauskas, Edward P.; Gamble, Bruce M.; Coonrad, Warren L.

2017-03-03

The northern Alaska Peninsula is a region of transition from the classic magmatic arc geology of the Alaska Peninsula to a Proterozoic and early Paleozoic carbonate platform and then to the poorly understood, tectonically complex sedimentary basins of southwestern Alaska. Physiographically, the region ranges from the high glaciated mountains of the Alaska-Aleutian Range to the coastal lowlands of Cook Inlet on the east and Bristol Bay on the southwest. The lower Ahklun Mountains and finger lakes on the west side of the map area show strong effects from glaciation. Structurally, a number of major faults cut the map area. Most important of these are the Bruin Bay Fault that parallels the coast of Cook Inlet, the Lake Clark Fault that cuts diagonally northeast to southwest across the eastern part of the map area, and the presently active Holitna Fault to the northwest that cuts surficial deposits.Distinctive rock packages assigned to three provinces are overlain by younger sedimentary rocks and intruded by widely dispersed latest Cretaceous and (or) early Tertiary granitic rocks. Much of the east half of the map area lies in the Alaska-Aleutian Range province; the Jurassic to Tertiary Alaska-Aleutian Range batholith and derivative Jurassic sedimentary rocks form the core of this province, which is intruded and overlain by the Aleutian magmatic arc. The Lime Hills province, the carbonate platform, occurs in the north-central part of the map area. The Paleozoic and Mesozoic Ahklun Mountains province in the western part of the map area includes abundant chert, argillite, and graywacke and lesser limestone, basalt, and tectonic mélange. The Kuskokwim Group, an Upper Cretaceous turbidite sequence, is extensively exposed and bounds all three provinces in the west-central part of the map area.

Modelling of Singapore's topographic transformation based on DEMs

NASA Astrophysics Data System (ADS)

Wang, Tao; Belle, Iris; Hassler, Uta

2015-02-01

Singapore's topography has been heavily transformed by industrialization and urbanization processes. To investigate topographic changes and evaluate soil mass flows, historical topographic maps of 1924 and 2012 were employed, and basic topographic features were vectorized. Digital elevation models (DEMs) for the two years were reconstructed based on vector features. Corresponding slope maps, a surface difference map and a scatter plot of elevation changes were generated and used to quantify and categorize the nature of the topographic transformation. The surface difference map is aggregated into five main categories of changes: (1) areas without significant height changes, (2) lowered-down areas where hill ranges were cut down, (3) raised-up areas where valleys and swamps were filled in, (4) reclaimed areas from the sea, and (5) new water-covered areas. Considering spatial proximity and configurations of different types of changes, topographic transformation can be differentiated as either creating inland flat areas or reclaiming new land from the sea. Typical topographic changes are discussed in the context of Singapore's urbanization processes. The two slope maps and elevation histograms show that generally, the topographic surface of Singapore has become flatter and lower since 1924. More than 89% of height changes have happened within a range of 20 m and 95% have been below 40 m. Because of differences in land surveying and map drawing methods, uncertainties and inaccuracies inherent in the 1924 topographic maps are discussed in detail. In this work, a modified version of a traditional scatter plot is used to present height transformation patterns intuitively. This method of deriving categorical maps of topographical changes from a surface difference map can be used in similar studies to qualitatively interpret transformation. Slope maps and histograms were also used jointly to reveal additional patterns of topographic change.

Expert system-based mineral mapping using AVIRIS

NASA Technical Reports Server (NTRS)

Kruse, Fred A.; Lefkoff, A. B.; Dietz, J. B.

1992-01-01

Integrated analysis of imaging spectrometer data and field spectral measurements were used in conjunction with conventional geologic field mapping to characterize bedrock and surficial geology at the northern end of Death Valley, California and Nevada. A knowledge-based expert system was used to automatically produce image maps from Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data showing the principal surface mineralogy. The imaging spectrometer data show the spatial distribution of spectrally distinct minerals occurring both as primary rock-forming minerals and as alteration and weathering products. Field spectral measurements were used to verify the mineral maps and field mapping was used to extend the remote sensing results. Geographically referenced image-maps produced from these data form new base maps from which to develop improved understanding of the processes of deposition and erosion affecting the present land surface. The 'northern Grapevine Mountains' (NGM) study area was reported on in numerous papers. This area is an unnamed northwestward extension of the range. Most of the research here has concentrated on mapping of Jurassic-age plutons and associated hydrothermal alteration, however, the nature and scope of these studies is much broader, pertaining to the geologic history and development of the entire Death Valley region. AVIRIS data for the NGM site were obtained during May 1989. Additional AVIRIS data were acquired during September 1989 as part of the Geologic Remote Sensing Field Experiment (GRSFE). The area covered by these data overlaps slightly with the May 1989 data. Three and one-half AVIRIS scenes total were analyzed.

Reconnaissance geologic mapping in the Dry Valleys of Antarctica using the Earth Resources Technology Satellite

NASA Technical Reports Server (NTRS)

Houston, R. S. (Principal Investigator); Zochol, F. W.; Smithson, S. B.

1973-01-01

The author has identified the following significant results. Reconnaissance geologic mapping can be done with 60-70% accuracy in the Dry Valleys of Antarctica using ERTS-1 imagery. Bedrock geology can be mapped much better than unconsolidated deposits of Quaternary age. Mapping of bedrock geology is facilitated by lack of vegetation, whereas mapping of Quaternary deposits is hindered by lack of vegetation. Antarctic images show remarkable clarity and under certain conditions (moderate relief, selection of the optimum band for specific rock types, stereo-viewing) irregular contacts can be mapped in local areas that are amazing like those mapped at a scale of 1:25,000, but, of course, lack details due to resolution limitations. ERTS-1 images should be a valuable aid to Antarctic geologists who have some limited ground truth and wish to extend boundaries of geologic mapping from known areas.

Surficial geologic map of the Dillingham quadrangle, southwestern Alaska

USGS Publications Warehouse

Wilson, Frederic H.

2018-05-14

The geologic map of the Dillingham quadrangle in southwestern Alaska shows surficial unconsolidated deposits, many of which are alluvial or glacial in nature. The map area, part of Alaska that was largely not glaciated during the late Wisconsin glaciation, has a long history reflecting local and more distant glaciations. Late Wisconsin glacial deposits have limited extent in the eastern part of the quadrangle, but are quite extensive in the western part of the quadrangle. This map and accompanying digital files are the result of the interpretation of black and white aerial photographs from the 1950s as well as more modern imagery. Limited new field mapping in the area was conducted as part of a bedrock mapping project in the northeastern part of the quadrangle; however, extensive aerial photographic interpretation represents the bulk of the mapping effort.

Detection of water bodies in Saline County, Kansas

NASA Technical Reports Server (NTRS)

Barr, B. G. (Principal Investigator)

1973-01-01

The author has identified the following significant results. A total of 2,272 water bodies were mapped in Saline County, Kansas in 1972 using ERTS-1 imagery. A topographic map of 1955 shows 1,056 water bodies in the county. The major increase took place in farm ponds. Preliminary comparison of image and maps indicates that water bodies larger than ten acres in area proved consistently detectable. Most water areas between four and ten acres are also detectable, although occasionally image context prevents detection. Water areas less than four acres in extent are sometimes detected, but the number varies greatly depending on image context and the individual interpretor.

Where Do Neurologists Look When Viewing Brain CT Images? An Eye-Tracking Study Involving Stroke Cases

PubMed Central

Matsumoto, Hideyuki; Terao, Yasuo; Yugeta, Akihiro; Fukuda, Hideki; Emoto, Masaki; Furubayashi, Toshiaki; Okano, Tomoko; Hanajima, Ritsuko; Ugawa, Yoshikazu

2011-01-01

The aim of this study was to investigate where neurologists look when they view brain computed tomography (CT) images and to evaluate how they deploy their visual attention by comparing their gaze distribution with saliency maps. Brain CT images showing cerebrovascular accidents were presented to 12 neurologists and 12 control subjects. The subjects' ocular fixation positions were recorded using an eye-tracking device (Eyelink 1000). Heat maps were created based on the eye-fixation patterns of each group and compared between the two groups. The heat maps revealed that the areas on which control subjects frequently fixated often coincided with areas identified as outstanding in saliency maps, while the areas on which neurologists frequently fixated often did not. Dwell time in regions of interest (ROI) was likewise compared between the two groups, revealing that, although dwell time on large lesions was not different between the two groups, dwell time in clinically important areas with low salience was longer in neurologists than in controls. Therefore it appears that neurologists intentionally scan clinically important areas when reading brain CT images showing cerebrovascular accidents. Both neurologists and control subjects used the “bottom-up salience” form of visual attention, although the neurologists more effectively used the “top-down instruction” form. PMID:22174928

Geologic map of south-central Yucca Mountain, Nye County, Nevada

USGS Publications Warehouse

Dickerson, Robert P.; Drake II, Ronald M.

2004-01-01

New 1:6,000-scale geologic mapping in a 20-square-kilometer area near the south end of Yucca Mountain, Nevada, which is the proposed site of an underground repository for the storage of high-level radioactive wastes, substantially supplements the stratigraphic and structural data obtained from earlier, 1:24,000-scale mapping. Principal observations and interpretations resulting from the larger scale, more detailed nature of the recent investigation include: (1) the thickness of the Miocene Tiva Canyon Tuff decreases from north to south within the map area, and the lithophysal zones within the formation have a greater lateral variability than in areas farther north; and (2) fault relations are far more complex than shown on previous maps, with both major (block-bounding) and minor (intrablock) faults showing much lateral variation in (a) the number of splays and (b) the amount, distribution, and width of anastomosing breccia and fracture zones.

Indicator Development for Potential Presence of Schistosomiasis Japonicum's Vector in Lake and Marshland Regions- A Case Study of Poyang Lake, Jiangxi Province, P.R. China

NASA Astrophysics Data System (ADS)

Marie, Tiphanie; Yesou, Herve; Huber, Claire; De Fraipont, Paul; Uribe, Carlos; Lacaux, Jean-Pierre; Lafaye, Murielle; Lai, Xijun; Desnos, Yves-Louis

2013-01-01

Earth observation data and bibliography on environmental parameters were used for mapping Oncomelania hupensis distribution, the Schistosomiasis japonicum’s intermediate host snail, within Poyang Lake (Jiangxi Province, P.R. China). Areas suitable for the development of O. hupensis, the vector of schistosomiasis, were derived from submersion time parameters and vegetation community indicators. ENVISAT time series data acquired from 2000 to 2009 were used for submersion times mapping, and 5 Beijing-1 data acquired during the dry season between 2006 and 2008 were used to map suitable vegetation for vector development. Yearly maps obtained indicate four principally potential endemic areas: the Gan Delta, the bank of the Fu He River, the Dalianzi Hu sector and the Poyang Lake Nature Reserve. Monthly maps from December 2005 to December 2008 show the dynamic of potential O. hupensis presence areas.

Influence of bicortical techniques in internal connection placed in premaxillary area by 3D finite element analysis.

PubMed

Verri, Fellippo Ramos; Cruz, Ronaldo Silva; Lemos, Cleidiel Aparecido Araújo; de Souza Batista, Victor Eduardo; Almeida, Daniel Augusto Faria; Verri, Ana Caroline Gonçales; Pellizzer, Eduardo Piza

2017-02-01

The aim of study was to evaluate the stress distribution in implant-supported prostheses and peri-implant bone using internal hexagon (IH) implants in the premaxillary area, varying surgical techniques (conventional, bicortical and bicortical in association with nasal floor elevation), and loading directions (0°, 30° and 60°) by three-dimensional (3D) finite element analysis. Three models were designed with Invesalius, Rhinoceros 3D and Solidworks software. Each model contained a bone block of the premaxillary area including an implant (IH, Ø4 × 10 mm) supporting a metal-ceramic crown. 178 N was applied in different inclinations (0°, 30°, 60°). The results were analyzed by von Mises, maximum principal stress, microstrain and displacement maps including ANOVA statistical test for some situations. Von Mises maps of implant, screws and abutment showed increase of stress concentration as increased loading inclination. Bicortical techniques showed reduction in implant apical area and in the head of fixation screws. Bicortical techniques showed slight increase stress in cortical bone in the maximum principal stress and microstrain maps under 60° loading. No differences in bone tissue regarding surgical techniques were observed. As conclusion, non-axial loads increased stress concentration in all maps. Bicortical techniques showed lower stress for implant and screw; however, there was slightly higher stress on cortical bone only under loads of higher inclinations (60°).

Preliminary Geologic Map of the Mount Hood 30- by 60-minute Quadrangle, Northern Cascade Range, Oregon

USGS Publications Warehouse

Sherrod, David R.; Scott, William E.

1995-01-01

This map shows the geology of the central and eastern parts of the Cascade Range in northern Oregon. The Quaternary andesitic stratovolcano of Mount Hood dominates the northwest quarter of the quadrangle, but nearly the entire area is underlain by arc-related volcanic and volcaniclastic rocks of the Cascade Range. Most stratigraphic units were emplaced since middle Miocene time, and all are Oligocene or younger. Despite the proximity of the map area to the Portland metropolitan area, large parts remained virtually unstudied or known only from limited reconnaissance until the late 1970s. A notable exception is the area surrounding Mount Hood, where mapping and chemical analyses by Wise (1969) provided a framework for geologic interpretation. Mapping since 1975 was conducted first to understand the stratigraphy and structure of the Columbia River Basalt Group (Anderson, 1978; Vogt, 1981; J.L. Anderson, in Swanson and others, 1981; Vandiver-Powell, 1978; Burck, 1986) and later to examine the geothermal potential of Mount Hood (Priest and others, 1982). Additional mapping was completed in 1985 for a geologic map of the Cascade Range in Oregon (Sherrod and Smith, 1989). From 1987 to 1990, detailed mapping was conducted in three 15-minute quadrangles on a limited basis (D.R. Sherrod, unpublished mapping) (see fig. 1 for index to mapping). An ongoing volcanic hazards study of Mount Hood by the U.S. Geological Survey (Scott and others, 1994) has provided the catalyst for completing the geologic map of the Mount Hood 30-minute by 60-minute quadrangle. As of June 1994, only two broad areas still remain largely unmapped. One of these areas, labeled 'unmapped' on the geologic map, lies in the Salmon River valley south of Zigzag along the west margin of the quadrangle. Although strata of the Columbia River Basalt Group in the Salmon River valley were mapped in detail by Burck (1986), the overlying middle and upper(?) Miocene lava flows, volcaniclastic strata, and intrusions have never been studied. The other poorly known area, the Mutton Mountains in the southeastern part of the map area, consists of Oligocene and lower Miocene volcanic and volcaniclastic rocks. Overlying lava flows of the Columbia River Basalt Group were mapped in some detail by Anderson (in Swanson and others, 1981).

Quantifying annual changes in built-up area in complex urban-rural landscapes from analyses of PALSAR and Landsat images

NASA Astrophysics Data System (ADS)

Qin, Yuanwei; Xiao, Xiangming; Dong, Jinwei; Chen, Bangqian; Liu, Fang; Zhang, Geli; Zhang, Yao; Wang, Jie; Wu, Xiaocui

2017-02-01

Built-up area supports human settlements and activities, and its spatial distribution and temporal dynamics have significant impacts on ecosystem services and global environment change. To date, most of urban remote sensing has generated the maps of impervious surfaces, and limited effort has been made to explicitly identify the area, location and density of built-up in the complex and fragmented landscapes based on the freely available datasets. In this study, we took the lower Yangtze River Delta (Landsat Path/Row: 118/038), China, where extensive urbanization and industrialization have occurred, as a case study site. We analyzed the structure and optical features of typical land cover types from (1) the HH and HV gamma-naught imagery from the Advanced Land Observation Satellite (ALOS) Phased Array type L-band Synthetic Aperture Radar (PALSAR), and (2) time series Landsat imagery. We proposed a pixel- and rule-based decision tree approach to identify and map built-up area at 30-m resolution from 2007 to 2010, using PALSAR HH gamma-naught and Landsat annual maximum Normalized Difference Vegetation Index (NDVImax). The accuracy assessment showed that the resultant annual maps of built-up had relatively high user (87-93%) and producer accuracies (91-95%) from 2007 to 2010. The built-up area was 2805 km2 in 2010, about 16% of the total land area of the study site. The annual maps of built-up in 2007-2010 show relatively small changes in the urban core regions, but large outward expansion along the peri-urban regions. The average annual increase of built-up areas was about 80 km2 per year from 2007 to 2010. Our annual maps of built-up in the lower Yangtze River Delta clearly complement the existing maps of impervious surfaces in the region. This study provides a promising new approach to identify and map built-up area, which is critical to investigate the interactions between human activities and ecosystem services in urban-rural systems.

Reconstructing time series water volumes of drying lakes in Central Asia with ZY-3 stereo remote sensing data

NASA Astrophysics Data System (ADS)

Li, J.; Warner, T.; Bao, A.

2017-12-01

Central Asia is one of the world most vulnerable areas responding to global change. Lakes in arid regions of Central Asia remain sensitive to climatic change and fluctuate with temperature and precipitation variations. Study showed that some central asian inland lakes in showed a trend of area shrinkage or extinct in the last decades. Quantitative analysis of lake volume changes in spatio-temporal processes will improve our understanding water resource utilization in arid regions and their responses to regional climate change. However, due to the lack of lake bathmetry or observation data, the volumes of these lakes remain unknown. In this paper, three lakes, such as Chaiwopu lake, Alik Lake and Selectyteniz Lake in Central Asia are used to reconstruct lake volume changes. Firstly, stereo mapping technologies derived from ZY-3 high resolution data are used to map the high-precision 3-D lake bathmetry, so as to create "Area-Level-Volume" based on contours of lake bathmetry. Secondly, time series lake areas in the last 50 years are mapped with multi-source and multi-temporal remote sensing images. Based on lake storage curves and time series lake areas, lake volumes in the last 5 decades can be reconstructed, and the spatio-temporal characteristics of lake volume changes and their mechanisms are also analyzed. The results showed that the high-precision lake hydrological elements are reconstructed on arid drying lakes through the application of stereo mapping technology in remote sensing.

Maps showing water geochemistry of the Buffalo Peaks Wilderness Study Area, Lake, Park, and Chaffee Counties, Colorado

USGS Publications Warehouse

Nowlan, G.A.; Ficklin, Walter H.; Dover, Robert A.

1985-01-01

This report presents results of geochemical studies carried out in June and July of 1982 in the Buffalo Peaks Wilderness Study Area, Colo. (see index map). Samples of water were collected from 84 streams and 18 springs draining the study area. Tabulations of the analyses and a sample locality map are in Ficklin and others (1984). The geochemistry of stream sediments and panned concentrates of the study area is in Nowlan and Gerstel (1985). The geology of the study area and vicinity is in Hedlund (1985). The mineral resource potential of the study area is described in Hedlund and others (1983). This report (1) assists in the assessment of the mineral resource potential of the Buffalo Peaks Wilderness Study Area; and (2) compares analyses of water samples with analyses of stream-sediment and panned-concentrate samples (Nowlan and Gerstel, 1985).

Map showing depth to pre-Cenozoic basement in the Death Valley ground-water model area, Nevada and California

USGS Publications Warehouse

Blakely, R.J.; Ponce, D.A.

2001-01-01

A depth to basement map of the Death Valley groundwater model area was prepared using over 40,0000 gravity stations as part of an interagency effort by the U.S. Geological Survey and the U.S. Department of Energy to help characterize the geology and hydrology of southwest Nevada and parts of California.

The difference between the potentiometric surfaces of the Magothy aquifer, September 1975 and September 1999 in southern Maryland

USGS Publications Warehouse

Curtin, Stephen E.; Andreasen, David C.; Wheeler, Judith C.

2001-01-01

This report presents a map showing the change in the potentiometric surface of the Magothy aquifer in the Magothy Formation of Cretaceous age in Southern Maryland for September 1975 and September 1999. The map, based on water level measurements in 61 wells, shows that the potentiometric surface during the 24-year period ranged from zero at the outcrop area, which is in the northernmost part of the study area, to a decline of 76 feet in Waldorf. Waldorf is located near the southwesternmost part of the study area, and approaches the downdip boundary of the aquifer.

The difference between the potentiometric surfaces of the Magothy aquifer, September 1975 and September 2003 in southern Maryland

USGS Publications Warehouse

Curtin, Stephen E.; Andreasen, David C.; Wheeler, Judith C.

2005-01-01

This report presents a map showing the change in the potentiometric surface of the Magothy aquifer in the Magothy Formation of Cretaceous age in Southern Maryland for September 1975 and September 2003. The map, based on water level measurements in 51 wells, shows that during the 28-year period, the potentiometric surface had no change at the outcrop area, which is in the northernmost part of the study area, but declined 71 feet at Waldorf. Waldorf is located near the southwesternmost part of the study area, and approaches the downdip boundary of the aquifer.

The Difference Between the Potentiometric Surfaces of the Magothy Aquifer, September 1975 and September 2001 in Southern Maryland

USGS Publications Warehouse

Curtin, Stephen E.; Andreasen, David C.; Wheeler, Judith C.

2002-01-01

This report presents a map showing the change in the potentiometric surface of the Magothy aquifer in the Magothy Formation of Cretaceous age in Southern Maryland for September 1975 and September 2001. The map, based on water level measurements in 54 wells, shows that during the 26-year period, the potentiometric surface ranged from zero at the outcrop area, which is in the northernmost part of the study area, to a decline of 75 feet at Waldorf. Waldorf is located near the southwesternmost part of the study area, and approaches the downdip boundary of the aquifer.

The Difference Between the Potentiometric Surfaces of the Magothy Aquifer in Southern Maryland, September 1975 and September 2007

USGS Publications Warehouse

Curtin, Stephen E.; Andreasen, David C.; Staley, Andrew W.

2009-01-01

This report presents a map showing the change in the potentiometric surface of the Magothy aquifer in the Magothy Formation of Late Cretaceous age in Southern Maryland for September 1975 and September 2007. The map, based on water-level measurements in 51 wells, shows that during the 32-year period, the potentiometric surface had no change at the outcrop area, which is in the northernmost part of the study area, but declined 90 feet at Waldorf. Waldorf is located near the southwesternmost part of the study area, and approaches the downdip boundary of the aquifer.

Intercomparison of Satellite-Derived Snow-Cover Maps

NASA Technical Reports Server (NTRS)

Hall, Dorothy K.; Tait, Andrew B.; Foster, James L.; Chang, Alfred T. C.; Allen, Milan

1999-01-01

In anticipation of the launch of the Earth Observing System (EOS) Terra, and the PM-1 spacecraft in 1999 and 2000, respectively, efforts are ongoing to determine errors of satellite-derived snow-cover maps. EOS Moderate Resolution Imaging Spectroradiometer (MODIS) and Advanced Microwave Scanning Radiometer-E (AMSR-E) snow-cover products will be produced. For this study we compare snow maps covering the same study area acquired from different sensors using different snow- mapping algorithms. Four locations are studied: 1) southern Saskatchewan; 2) a part of New England (New Hampshire, Vermont and Massachusetts) and eastern New York; 3) central Idaho and western Montana; and 4) parts of North and South Dakota. Snow maps were produced using a prototype MODIS snow-mapping algorithm used on Landsat Thematic Mapper (TM) scenes of each study area at 30-m and when the TM data were degraded to 1 -km resolution. National Operational Hydrologic Remote Sensing Center (NOHRSC) 1 -km resolution snow maps were also used, as were snow maps derived from 1/2 deg. x 1/2 deg. resolution Special Sensor Microwave Imager (SSM/1) data. A land-cover map derived from the International Geosphere-Biosphere Program (IGBP) land-cover map of North America was also registered to the scenes. The TM, NOHRSC and SSM/I snow maps, and land-cover maps were compared digitally. In most cases, TM-derived maps show less snow cover than the NOHRSC and SSM/I maps because areas of incomplete snow cover in forests (e.g., tree canopies, branches and trunks) are seen in the TM data, but not in the coarser-resolution maps. The snow maps generally agree with respect to the spatial variability of the snow cover. The 30-m resolution TM data provide the most accurate snow maps, and are thus used as the baseline for comparison with the other maps. Comparisons show that the percent change in amount of snow cover relative to the 3 0-m resolution TM maps is lowest using the TM I -km resolution maps, ranging from 0 to 40%. The highest percent change (less than 100%) is found in the New England study area, probably due to the presence of patchy snow cover. A scene with patchy snow cover is more difficult to map accurately than is a scene with a well-defined snowline such as is found on the North and South Dakota scene where the percent change ranged from 0 to 40%. There are also some important differences in the amount of snow mapped using the two different SSM/I algorithms because they utilize different channels.

Altitude, depth, and thickness of the Galena-Platteville Bedrock Unit in the subcrop area of Illinois and Wisconsin

USGS Publications Warehouse

Brown, Timothy A.; Dunning, Charles P.; Sharpe, Jennifer B.

2000-01-01

The report series will enable investigators involved in site-specific studies within the subcrop area to understand the regional geologic framework of the unit and to find additional reference sources. This report consists of four sheets that show the altitude (sheet 1), depth from land surface (sheet 2), total thickness (sheet 3), and location of altitude data (sheet 4) of the lithologic units that constitute the Galena-Platteville bedrock unit within the subcrop area. The sheets also show major known geologic features within the Galena-Platteville study area in Illinois and Wisconsin. A geographic information system (GIS) was used to generate data layers (coverages) from point data and from published and unpublished contour maps at various scales and detail. Standard GIS procedures were used to change the coverages into the maps shown on the sheets presented in this report. A list of references for the data used to prepare the maps is provided. 

New NASA Satellite Flood Map of Southeastern Texas (Sentinel-1 Data)

NASA Image and Video Library

2017-08-31

The Advanced Rapid Imaging and Analysis (ARIA) team at NASA's Jet Propulsion Laboratory in Pasadena, California, used synthetic aperture radar imagery from the European Space Agency's (ESA) Sentinel-1 satellite to create this Flood Proxy Map of Southeastern Texas, showing areas that are likely flooded as a result of Hurricane Harvey (light blue pixels). The images used to create the map were taken before (Aug. 5, 2017) and after (Aug. 29, 2017) Hurricane Harvey made landfall. The map covers an area of 155 by 211 miles (250 by 340 kilometers). Each pixel measures about 33 yards (30 meters) across. Local ground observations provided anecdotal preliminary validation. The results were also cross-validated with the ARIA ALOS-2 flood proxy map v0.2. The map should be used as guidance, and may be less reliable over urban areas. Sentinel-1 data were accessed through the Copernicus Open Access Hub. Contains modified Copernicus Sentinel data 2017. https://photojournal.jpl.nasa.gov/catalog/PIA21932

Radar Shows Italy Area Moved 8 Inches by Amatrice Earthquake

NASA Image and Video Library

2016-08-27

NASA and its partners are contributing observations and expertise to the ongoing response to the Aug. 23, 2016, magnitude 6.2 Amatrice earthquake in central Italy caused widespread building damage to several towns throughout the region. This earthquake was the strongest in that area since the 2009 earthquake that destroyed the city of L'Aquila. Scientists with the Advanced Rapid Imaging and Analysis project (ARIA), a collaboration between NASA's Jet Propulsion Laboratory, Pasadena, California, and the California Institute of Technology in Pasadena, analyzed interferometric synthetic aperture radar images from the PALSAR-2 instrument on the ALOS-2 satellite operated by the Japan Aerospace Exploration Agency (JAXA) to calculate a map of the deformation of Earth's surface caused by the quake. This false-color map shows the amount of permanent surface movement, as viewed by the satellite, during a seven-month interval between two ALOS-2 images acquired on Sept. 9, 2015 and Aug. 24, 2016. The movement was caused almost entirely by the earthquake. In this map, the colors of the surface displacements are proportional to the surface motion. The red and pink tones show the areas where the land moved toward the satellite by up to 2 inches (5 centimeters). The area with various shades of blue moved away from the satellite, mostly downward, by as much as 8 inches (20 centimeters). Contours on the surface motion are 2 inches (5 centimeters) The green star shows the epicenter where the earthquake started as located by the U.S. Geological Survey National Earthquake Information Center. Black dots show town locations. Scientists use these maps to build detailed models of the fault slip at depth and associated land movements to better understand the impact on future earthquake activity. The map shows the fault or faults that moved in the earthquake is about 14 miles (22 kilometers) long between Amatrice and Norcia and slopes to the west beneath the area that moved downward. The PALSAR-2 data were provided by JAXA through a science project. http://photojournal.jpl.nasa.gov/catalog/PIA20893

Geologic framework, structure, and hydrogeologic characteristics of the Knippa Gap area in eastern Uvalde and western Medina Counties, Texas

USGS Publications Warehouse

Clark, Allan K.; Pedraza, Diana E.; Morris, Robert R.

2013-01-01

By using data that were compiled and collected for this study and previous studies, a revised map was constructed depicting the geologic framework, structure, and hydrogeologic characteristics of the Knippa Gap area in eastern Uvalde and western Medina Counties, Tex. The map also shows the interpreted structural dip directions and interpreted location of a structural low (trough) in the area known as the Knippa Gap.

Evaluation of nine-frame enhanced multiband photography San Andreas fault zone, Carrizo Plain, California

NASA Technical Reports Server (NTRS)

Wallace, R. E.

1969-01-01

Nine-frame multiband aerial photography of a sample area 4500 feet on a side was processed to enhance spectral contrasts. The area concerned is in the Carrizo Plain, 45 miles west of Bakersfield, California, in sec. 29, T 31 S., R. 21 E., as shown on the Panorama Hills quadrangle topographic map published by the U. S. Geological Survey. The accompany illustrations include an index map showing the location of the Carrizo Plain area; a geologic map of the area based on field studies and examination of black and white aerial photographs; an enhanced multiband aerial photograph; an Aero Ektachrome photograph; black and white aerial photographs; and infrared image in the 8-13 micron band.

The World Karst Aquifer Mapping project: concept, mapping procedure and map of Europe

NASA Astrophysics Data System (ADS)

Chen, Zhao; Auler, Augusto S.; Bakalowicz, Michel; Drew, David; Griger, Franziska; Hartmann, Jens; Jiang, Guanghui; Moosdorf, Nils; Richts, Andrea; Stevanovic, Zoran; Veni, George; Goldscheider, Nico

2017-05-01

Karst aquifers contribute substantially to freshwater supplies in many regions of the world, but are vulnerable to contamination and difficult to manage because of their unique hydrogeological characteristics. Many karst systems are hydraulically connected over wide areas and require transboundary exploration, protection and management. In order to obtain a better global overview of karst aquifers, to create a basis for sustainable international water-resources management, and to increase the awareness in the public and among decision makers, the World Karst Aquifer Mapping (WOKAM) project was established. The goal is to create a world map and database of karst aquifers, as a further development of earlier maps. This paper presents the basic concepts and the detailed mapping procedure, using France as an example to illustrate the step-by-step workflow, which includes generalization, differentiation of continuous and discontinuous carbonate and evaporite rock areas, and the identification of non-exposed karst aquifers. The map also shows selected caves and karst springs, which are collected in an associated global database. The draft karst aquifer map of Europe shows that 21.6% of the European land surface is characterized by the presence of (continuous or discontinuous) carbonate rocks; about 13.8% of the land surface is carbonate rock outcrop.

Texture, Carbonate Content, and Preliminary Maps of Surficial Sediments of the Flower Garden Banks Area, Northwestern Gulf of Mexico Outer Shelf

USGS Publications Warehouse

Scanlon, Kathryn M.; Ackerman, Seth D.; Rozycki, Jill E.

2003-01-01

The purpose of this report is to release texture and carbonate content analyses of 107 seafloor sediments collected within and near the East and West Flower Garden Banks areas of the Sanctuary and to show relationships between these data and existing bathymetric data. The sediment data, in conjunction with previously collected geological, geophysical and biological data were used to construct a reconnaissance-scale map of the distribution of seafloor sediment types. This map will be useful for resource managers and can be used, with additional data, as a basis for future habitat mapping.

Detection of alteration associated with a porphyry copper deposit in southern Arizona

NASA Technical Reports Server (NTRS)

Abrams, M. J.; Siegal, B. S.

1977-01-01

Computer processing of Landsat MSS data was performed using contrast stretching and band-to-band ratioing. A false color ratio composite picture showed color anomalies which coincided with known areas of alteration on and about Red Mountain. A helicopter survey of the study area was undertaken using a portable field reflectance spectrometer. One hundred fifty-six spectra were obtained in the 0.4 to 2.5 micrometer wavelength region. The spectra were digitized, and contour maps for 24 wavelength intervals were produced; no spectral anomalies were evident for the known altered areas. A contour map produced from the 1.6 and 2.2 micrometer ratio generally delineated the alteration areas. The 1.3, 1.6, and 2.2 micrometer wavelength data were canonically transformed using a transformation empirically derived from discriminant function analysis of altered and unaltered materials for the Goldfield, Nevada region, and a contour map was produced for the first canonical variable. The known areas of alteration were clearly defined on the contour map.

Structural Maps of the V-17 Beta Regio Quadrangle, Venus

NASA Technical Reports Server (NTRS)

Basilevsky, A. t.; Head, James W.

2008-01-01

These represent slices of the geologic map into 7 time-stratigraphic levels whose descriptions are found in [3-6]. From older to younger they are: 1) Tessera material unit (t), 2) Densely fractured plains material unit (pdf), 3) Fractured and ridged plains material unit (pfr), 4) Tessera transitional terrain structural unit (tt), 5) Fracture belts structural unit (fb), 6) Shield plains (psh) and plains with wrinkle ridges (pwr) material units combined, and 7) Lobate (pl) and smooth (ps) plains material units combined and, approximately contemporaneous with them, the structural unit of rifted terrain (rt). Each slice shows the generalized pattern of structures typical of these units. Figures 1-7 show the seven maps and Figure 8 shows the combined map illustrating what is shown in the seven maps. To visualize the Beta Regio uplift outlines, the major structure of this area, we show the +0.5 km and +2.5 km contour lines, corresponding respectively to the base and the mid-height of the uplift. It is seen in Figures 1-2 and 4 the trends of t, pdf and tt occupy relatively small areas and their structures seen in these small windows appear rather variable and with almost no orientation heritage with time. Figure 3 shows that swarms of ridge belts trend mostly NW and go through the Beta structure with no alignment with it, suggesting that this structure did not yet exist at this time. Figure 5 shows that fracture belts align along the northern base of the Beta uplift suggesting onset of the formation of this structure. Figure 6 shows that wrinkle ridges do not show alignment with the Beta uplift suggesting that this already forming structure was not high enough to exert topographic stress in its vicinity. Figure 7 shows that the Beta uplift has Devana Chasma as an axial rift zone, suggesting a genetic link between the uplift and rifting. Figure 8 shows that structural trends in this area significantly changed with time.

Weights of Evidence Method for Landslide Susceptibility Mapping in Takengon, Central Aceh, Indonesia

NASA Astrophysics Data System (ADS)

Pamela; Sadisun, Imam A.; Arifianti, Yukni

2018-02-01

Takengon is an area prone to earthquake disaster and landslide. On July 2, 2013, Central Aceh earthquake induced large numbers of landslides in Takengon area, which resulted in casualties of 39 people. This location was chosen to assess the landslide susceptibility of Takengon, using a statistical method, referred to as the weight of evidence (WoE). This WoE model was applied to indicate the main factors influencing the landslide susceptible area and to derive landslide susceptibility map of Takengon. The 251 landslides randomly divided into two groups of modeling/training data (70%) and validation/test data sets (30%). Twelve thematic maps of evidence are slope degree, slope aspect, lithology, land cover, elevation, rainfall, lineament, peak ground acceleration, curvature, flow direction, distance to river and roads used as landslide causative factors. According to the AUC, the significant factor controlling the landslide is the slope, the slope aspect, peak ground acceleration, elevation, lithology, flow direction, lineament, and rainfall respectively. Analytical result verified by using test data of landslide shows AUC prediction rate is 0.819 and AUC success rate with all landslide data included is 0.879. This result showed the selective factors and WoE method as good models for assessing landslide susceptibility. The landslide susceptibility map of Takengon shows the probabilities, which represent relative degrees of susceptibility for landslide proneness in Takengon area.

Understanding natural systems; a perspective for land-use planning in Appalachian Kentucky

USGS Publications Warehouse

Newell, Wayne L.

1978-01-01

An eight-county area at the headwaters of the Kentucky River has been designated the Kentucky River Area Development District (KRADD) by the Appalachian Regional Commission. The objective of the project described in this report has been to provide materials to KRADD planners in a format and containing terminology usable by local people untrained in earth science. Experimental maps (not included in this report) have been prepared largely from preexisting data. Time and cost limitations required a regional analysis as well as somewhat more detailed examples of selected localities. Most of the maps produced to meet these needs show the abundance and distribution of naturally occurring materials and the areas affected by various geomorphic processes. Three types of maps, showing current land use, slope, and flood-prone areas, present both basic and derived data directly applicable to specific land-use decisions. Basic map information on quality and quantity of surface and ground water, bedrock and surficial geology, and mineral fuels can be interpreted for a wide variety of current and potential uses. Texts accompanying the maps explain bedrock control of geomorphic processes, distribution and significance of surficial deposits, and hydrologic characteristics of the intricately dissected eastern Kentucky terrain. Within this conceptual framework, geomorphic processes and the landscape may be evaluated in humanly significant terms of low to high potential risk, thereby indicating both opportunities and limitations for land use.

Geological analysis of parts of the southern Arabian Shield based on Landsat imagery

NASA Astrophysics Data System (ADS)

Qari, Mohammed Yousef Hedaytullah T.

This thesis examines the capability and applicability of Landsat multispectral remote sensing data for geological analysis in the arid southern Arabian Shield, which is the eastern segment of the Nubian-Arabian Shield surrounding the Red Sea. The major lithologies in the study area are Proterozoic metavolcanics, metasediments, gneisses and granites. Three test-sites within the study area, located within two tectonic assemblages, the Asir Terrane and the Nabitah Mobile Belt, were selected for detailed comparison of remote sensing methods and ground geological studies. Selected digital image processing techniques were applied to full-resolution Landsat TM imagery and the results are interpreted and discussed. Methods included: image contrast improvement, edge enhancement for detecting lineaments and spectral enhancement for geological mapping. The last method was based on two principles, statistical analysis of the data and the use of arithmetical operators. New and detailed lithological and structural maps were constructed and compared with previous maps of these sites. Examples of geological relations identified using TM imagery include: recognition and mapping of migmatites for the first time in the Arabian Shield; location of the contact between the Asir Terrane and the Nabitah Mobile Belt; and mapping of lithologies, some of which were not identified on previous geological maps. These and other geological features were confirmed by field checking. Methods of lineament enhancement implemented in this study revealed structural lineaments, mostly mapped for the first time, which can be related to regional tectonics. Structural analysis showed that the southern Arabian Shield has been affected by at least three successive phases of deformation. The third phase is the most dominant and widespread. A crustal evolutionary model in the vicinity of the study area is presented showing four stages, these are: arc stage, accretion stage, collision stage and post-collision stage. The results of this study demonstrate that Landsat TM data can be used reliably for geological investigations in the Arabian Shield and comparable areas, particularly to generate detailed geological maps over large areas by using quantitative remote sensing methods, providing there is prior knowledge of part of the area.

Climate Ready Estuaries Partner Projects Map

EPA Pesticide Factsheets

CRE partners with the National Estuary Program to develop climate change projects in coastal U.S. areas, such as bays and harbors; to develop adaptation action plans, identify climate impacts and indicators, and more. This map shows project locations.

Natural speech reveals the semantic maps that tile human cerebral cortex

PubMed Central

Huth, Alexander G.; de Heer, Wendy A.; Griffiths, Thomas L.; Theunissen, Frédéric E.; Gallant, Jack L.

2016-01-01

The meaning of language is represented in regions of the cerebral cortex collectively known as the “semantic system”. However, little of the semantic system has been mapped comprehensively, and the semantic selectivity of most regions is unknown. Here we systematically map semantic selectivity across the cortex using voxel-wise modeling of fMRI data collected while subjects listened to hours of narrative stories. We show that the semantic system is organized into intricate patterns that appear consistent across individuals. We then use a novel generative model to create a detailed semantic atlas. Our results suggest that most areas within the semantic system represent information about specific semantic domains, or groups of related concepts, and our atlas shows which domains are represented in each area. This study demonstrates that data-driven methods—commonplace in studies of human neuroanatomy and functional connectivity—provide a powerful and efficient means for mapping functional representations in the brain. PMID:27121839

Evaluation of ERTS-1 imagery for mapping Quaternary deposits and landforms in the Great Plains and Midwest

NASA Technical Reports Server (NTRS)

Morrison, R. B. (Principal Investigator); Hallberg, G. R.

1973-01-01

The author has identified the following significant results. The main landform associations and larger landforms are readily identifiable on the better images and commonly the gross associations of surficial Quaternary deposits also can be determined primarily by information on landforms and soils (obtained by analysis of stream dissection and drainage and stream-divide patterns, land use patterns, etc.). Maps showing the Quaternary geologic-terrain units that can be distinguished on the ERTS-1 images are being prepared for study areas in Illinois, Iowa, Missouri, Kansas, Nebraska, and South Dakota. Preliminary maps of 1:1,000,000 scale are included for three of the study areas: the Grand Island and Fremont, Nebraska, and the Davenport, Iowa-Illinois, 1 deg x 2 deg quadrangles. These maps exemplify the first phase of investigations, which consists of identifying and mapping landform and land use characteristics and geologic-surficial materials directly from the ERTS-1 images alone, with no additional information. These maps show that commonly the boundaries of geologic-terrain units can be delineated more accurately on ERTS-1 images than on topographic maps at 1:250,000 scale.

Annual Changes of Paddy Rice Planting Areas in Northeastern Asia from MODIS images in 2000-2014

NASA Astrophysics Data System (ADS)

Xiao, X.; Zhang, G.; Dong, J.; Menarguez, M. A.; Kou, W.; Jin, C.; Qin, Y.; Zhou, Y.; Wang, J.; Moore, B., III

2014-12-01

Knowledge of the area and spatial distribution of paddy rice is important for assessment of food security, management of water resources, estimation of greenhouse gas (methane) emissions, and understanding avian influenza virus transmission. Over the past two decades, paddy rice cultivation has expanded northward in temperate and cold temperate zones, particularly in Northeastern China. There is a need to quantify and map changes in paddy rice planting areas in Northeastern Asia (Japan, North and South Korea, and northeast China) at annual interval. We developed a pixel- and phenology-based image analysis system, MODIS-RICE, to map the paddy rice in Northeastern Asia by using multi-temporal MODIS thermal and surface reflectance imagery. Paddy rice fields during the flooding and transplanting phases have unique physical and spectral characteristics, which make it possible for the development of an automated and robust algorithm to track flooding and transplanting phases of paddy rice fields over time. In this presentation, we will show the MODIS-based annual maps of paddy rice planting area in the Northeastern Asia from 2000-2014 (500-m spatial resolution). Accuracy assessments using high-resolution images show that the resultant paddy rice map of Northeastern Asia had a comparable accuracy to the existing products, including 2010 Landsat-based National Land Cover Dataset (NLCD) of China, the 2010 RapidEye-based paddy rice map in North Korea, and the 2010 AVNIR-2-based National Land Cover Dataset in Japan in terms of both area and spatial pattern of paddy rice. This study has demonstrated that our novel MODIS-Rice system, which use both thermal and optical MODIS data over a year, are simple and robust tools to identify and map paddy rice fields in temperate and cold temperate zones.

Remote sensing and GIS-based landslide hazard analysis and cross-validation using multivariate logistic regression model on three test areas in Malaysia

NASA Astrophysics Data System (ADS)

Pradhan, Biswajeet

2010-05-01

This paper presents the results of the cross-validation of a multivariate logistic regression model using remote sensing data and GIS for landslide hazard analysis on the Penang, Cameron, and Selangor areas in Malaysia. Landslide locations in the study areas were identified by interpreting aerial photographs and satellite images, supported by field surveys. SPOT 5 and Landsat TM satellite imagery were used to map landcover and vegetation index, respectively. Maps of topography, soil type, lineaments and land cover were constructed from the spatial datasets. Ten factors which influence landslide occurrence, i.e., slope, aspect, curvature, distance from drainage, lithology, distance from lineaments, soil type, landcover, rainfall precipitation, and normalized difference vegetation index (ndvi), were extracted from the spatial database and the logistic regression coefficient of each factor was computed. Then the landslide hazard was analysed using the multivariate logistic regression coefficients derived not only from the data for the respective area but also using the logistic regression coefficients calculated from each of the other two areas (nine hazard maps in all) as a cross-validation of the model. For verification of the model, the results of the analyses were then compared with the field-verified landslide locations. Among the three cases of the application of logistic regression coefficient in the same study area, the case of Selangor based on the Selangor logistic regression coefficients showed the highest accuracy (94%), where as Penang based on the Penang coefficients showed the lowest accuracy (86%). Similarly, among the six cases from the cross application of logistic regression coefficient in other two areas, the case of Selangor based on logistic coefficient of Cameron showed highest (90%) prediction accuracy where as the case of Penang based on the Selangor logistic regression coefficients showed the lowest accuracy (79%). Qualitatively, the cross application model yields reasonable results which can be used for preliminary landslide hazard mapping.

Response variance in functional maps: neural darwinism revisited.

PubMed

Takahashi, Hirokazu; Yokota, Ryo; Kanzaki, Ryohei

2013-01-01

The mechanisms by which functional maps and map plasticity contribute to cortical computation remain controversial. Recent studies have revisited the theory of neural Darwinism to interpret the learning-induced map plasticity and neuronal heterogeneity observed in the cortex. Here, we hypothesize that the Darwinian principle provides a substrate to explain the relationship between neuron heterogeneity and cortical functional maps. We demonstrate in the rat auditory cortex that the degree of response variance is closely correlated with the size of its representational area. Further, we show that the response variance within a given population is altered through training. These results suggest that larger representational areas may help to accommodate heterogeneous populations of neurons. Thus, functional maps and map plasticity are likely to play essential roles in Darwinian computation, serving as effective, but not absolutely necessary, structures to generate diverse response properties within a neural population.

Response Variance in Functional Maps: Neural Darwinism Revisited

PubMed Central

Takahashi, Hirokazu; Yokota, Ryo; Kanzaki, Ryohei

2013-01-01

The mechanisms by which functional maps and map plasticity contribute to cortical computation remain controversial. Recent studies have revisited the theory of neural Darwinism to interpret the learning-induced map plasticity and neuronal heterogeneity observed in the cortex. Here, we hypothesize that the Darwinian principle provides a substrate to explain the relationship between neuron heterogeneity and cortical functional maps. We demonstrate in the rat auditory cortex that the degree of response variance is closely correlated with the size of its representational area. Further, we show that the response variance within a given population is altered through training. These results suggest that larger representational areas may help to accommodate heterogeneous populations of neurons. Thus, functional maps and map plasticity are likely to play essential roles in Darwinian computation, serving as effective, but not absolutely necessary, structures to generate diverse response properties within a neural population. PMID:23874733

A search for stratiform massive-sulfide exploration targets in Appalachian Devonian rocks; a case study using computer-assisted attribute-coincidence mapping

USGS Publications Warehouse

Wedow, Helmuth

1983-01-01

The empirical model for sediment-associated, stratiform, exhalative, massive-sulfide deposits presented by D. Large in 1979 and 1980 has been redesigned to permit its use in a computer-assisted search for exploration-target areas in Devonian rocks of the Appalachian region using attribute-coincidence mapping (ACM). Some 36 gridded-data maps and selected maps derived therefrom were developed to show the orthogonal patterns, using the 7-1/2 minute quadrangle as an information cell, of geologic data patterns relevant to the empirical model. From these map and data files, six attribute-coincidence maps were prepared to illustrate both variation in the application of ACM techniques and the extent of possible significant exploration-target areas. As a result of this preliminary work in ACM, four major (and some lesser) exploration-target areas needing further study and analysis have been defined as follows: 1) in western and central New York in the outcrop area of lowermost Upper Devonian rocks straddling the Clarendon-Linden fault; 2) in western Virginia and eastern West Virginia in an area largely coincident with the well-known 'Oriskany' Mn-Fe ores; 3) an area in West Virginia, Maryland, and Virginia along and nearby the trend of the Alabama-New York lineament of King and Zietz approximately between 38- and 40-degrees N. latitude; and 4) an area in northeastern Ohio overlying an area coincident with a significant thickness of Silurian salt and high modern seismic activity. Some lesser, smaller areas suggested by relatively high coincidence may also be worthy of further study.

Proposal for a study of computer mapping of terrain using multispectral data from ERTS-A for the Yellowstone National Park test site

NASA Technical Reports Server (NTRS)

Smedes, H. W. (Principal Investigator); Root, R. R.; Roller, N. E. G.; Despain, D.

1978-01-01

The author has identified the following significant results. A terrain map of Yellowstone National Park showed plant community types and other classes of ground cover in what is basically a wild land. The map comprised 12 classes, six of which were mapped with accuracies of 70 to 95%. The remaining six classes had spectral reflectances that overlapped appreciably, and hence, those were mapped less accurately. Techniques were devised for quantitatively comparing the recognition map of the park with control data acquired from ground inspection and from analysis of sidelooking radar images, a thermal IR mosaic, and IR aerial photos of several scales. Quantitative analyses were made in ten 40 sq km test areas. Comparison mechanics were performed by computer with the final results displayed on line printer output. Forested areas were mapped by computer using ERTS data for less than 1/4 the cost of the conventional forest mapping technique for topographic base maps.

Map showing mineral resource potential of the Sierra Ancha Wilderness and Salome Study Area, Gila County, Arizona

USGS Publications Warehouse

Otton, James K.; Light, Thomas D.; Shride, Andrew F.; Bergquist, Joel R.; Wrucke, Chester T.; Theobald, Paul K.; Duval, Joseph S.; Wilson, Dolores M.

1981-01-01

The Wilderness Act (Public Law 88-577, Sept. 3, 1964) and certain related Acts require the Geological Survey and the Bureau of Mines to survey certain areas on Federal lands to determine their mineral-resource potential. Results must be made available to the public and be submitted to the Administration and the Congress. These maps and reports present the results of a geologic and mineral survey of the Sierra Ancha Wilderness and Salome Study Area, Gila County, Arizona.

Automated Radar Image of Deformation for Amatrice, Italy Earthquake

NASA Image and Video Library

2016-08-31

Amatrice earthquake in central Italy, which caused widespread building damage to several towns throughout the region. This earthquake was the strongest in that area since the 2009 earthquake that destroyed the city of L'Aquila. The Advanced Rapid Imaging and Analysis (ARIA) data system, a collaborative project between NASA's Jet Propulsion Laboratory, Pasadena, California, and the California Institute of Technology in Pasadena, automatically generated interferometric synthetic aperture radar images from the Copernicus Sentinel 1A satellite operated by the European Space Agency (ESA) for the European Commission to calculate a map of the deformation of Earth's surface caused by the quake. This false-color map shows the amount of permanent surface movement, as viewed by the satellite, during a 12-day interval between two Sentinel 1 images acquired on Aug. 15, 2016, and Aug. 27, 2016. The movement was caused almost entirely by the earthquake. In this map, the colors of the surface displacements are proportional to the surface motion. The red and pink tones show the areas where the land moved toward the satellite by up to 2 inches (5 centimeters). The area with various shades of blue moved away from the satellite, mostly downward, by as much as 8 inches (20 centimeters). Contours on the surface motion are 2 inches (5 centimeters) The green star shows the epicenter where the earthquake started as located by the U.S. Geological Survey National Earthquake Information Center. Black dots show town locations. Scientists use these maps to build detailed models of the fault slip at depth and associated land movements to better understand the impact on future earthquake activity. The map shows the fault or faults that moved in the earthquake is about 14 miles (22 kilometers) long between Amatrice and Norcia and slopes to the west beneath the area that moved downward. http://photojournal.jpl.nasa.gov/catalog/PIA20896

On the Invariant Cantor Sets of Period Doubling Type of Infinitely Renormalizable Area-Preserving Maps

NASA Astrophysics Data System (ADS)

Lilja, Dan

2018-03-01

Since its inception in the 1970s at the hands of Feigenbaum and, independently, Coullet and Tresser the study of renormalization operators in dynamics has been very successful at explaining universality phenomena observed in certain families of dynamical systems. The first proof of existence of a hyperbolic fixed point for renormalization of area-preserving maps was given by Eckmann et al. (Mem Am Math Soc 47(289):vi+122, 1984). However, there are still many things that are unknown in this setting, in particular regarding the invariant Cantor sets of infinitely renormalizable maps. In this paper we show that the invariant Cantor set of period doubling type of any infinitely renormalizable area-preserving map in the universality class of the Eckmann-Koch-Wittwer renormalization fixed point is always contained in a Lipschitz curve but never contained in a smooth curve. This extends previous results by de Carvalho, Lyubich and Martens about strongly dissipative maps of the plane close to unimodal maps to the area-preserving setting. The method used for constructing the Lipschitz curve is very similar to the method used in the dissipative case but proving the nonexistence of smooth curves requires new techniques.

Flood mapping from Sentinel-1 and Landsat-8 data: a case study from river Evros, Greece

NASA Astrophysics Data System (ADS)

Kyriou, Aggeliki; Nikolakopoulos, Konstantinos

2015-10-01

Floods are suddenly and temporary natural events, affecting areas which are not normally covered by water. The influence of floods plays a significant role both in society and the natural environment, therefore flood mapping is crucial. Remote sensing data can be used to develop flood map in an efficient and effective way. This work is focused on expansion of water bodies overtopping natural levees of the river Evros, invading the surroundings areas and converting them in flooded. Different techniques of flood mapping were used using data from active and passive remote sensing sensors like Sentinlel-1 and Landsat-8 respectively. Space borne pairs obtained from Sentinel-1 were processed in this study. Each pair included an image during the flood, which is called "crisis image" and another one before the event, which is called "archived image". Both images covering the same area were processed producing a map, which shows the spread of the flood. Multispectral data From Landsat-8 were also processed in order to detect and map the flooded areas. Different image processing techniques were applied and the results were compared to the respective results of the radar data processing.

Alabama-Mississippi Coastal Classification Maps - Perdido Pass to Cat Island

USGS Publications Warehouse

Morton, Robert A.; Peterson, Russell L.

2005-01-01

The primary purpose of the USGS National Assessment of Coastal Change Project is to provide accurate representations of pre-storm ground conditions for areas that are designated high-priority because they have dense populations or valuable resources that are at risk from storm waves. Another purpose of the project is to develop a geomorphic (land feature) coastal classification that, with only minor modification, can be applied to most coastal regions in the United States. A Coastal Classification Map describing local geomorphic features is the first step toward determining the hazard vulnerability of an area. The Coastal Classification Maps of the National Assessment of Coastal Change Project present ground conditions such as beach width, dune elevations, overwash potential, and density of development. In order to complete a hazard vulnerability assessment, that information must be integrated with other information, such as prior storm impacts and beach stability. The Coastal Classification Maps provide much of the basic information for such an assessment and represent a critical component of a storm-impact forecasting capability. The map above shows the areas covered by this web site. Click on any of the location names or outlines to view the Coastal Classification Map for that area.

Linear programming model to develop geodiversity map using utility theory

NASA Astrophysics Data System (ADS)

Sepehr, Adel

2015-04-01

In this article, the classification and mapping of geodiversity based on a quantitative methodology was accomplished using linear programming, the central idea of which being that geosites and geomorphosites as main indicators of geodiversity can be evaluated by utility theory. A linear programming method was applied for geodiversity mapping over Khorasan-razavi province located in eastern north of Iran. In this route, the main criteria for distinguishing geodiversity potential in the studied area were considered regarding rocks type (lithology), faults position (tectonic process), karst area (dynamic process), Aeolian landforms frequency and surface river forms. These parameters were investigated by thematic maps including geology, topography and geomorphology at scales 1:100'000, 1:50'000 and 1:250'000 separately, imagery data involving SPOT, ETM+ (Landsat 7) and field operations directly. The geological thematic layer was simplified from the original map using a practical lithologic criterion based on a primary genetic rocks classification representing metamorphic, igneous and sedimentary rocks. The geomorphology map was provided using DEM at scale 30m extracted by ASTER data, geology and google earth images. The geology map shows tectonic status and geomorphology indicated dynamic processes and landform (karst, Aeolian and river). Then, according to the utility theory algorithms, we proposed a linear programming to classify geodiversity degree in the studied area based on geology/morphology parameters. The algorithm used in the methodology was consisted a linear function to be maximized geodiversity to certain constraints in the form of linear equations. The results of this research indicated three classes of geodiversity potential including low, medium and high status. The geodiversity potential shows satisfied conditions in the Karstic areas and Aeolian landscape. Also the utility theory used in the research has been decreased uncertainty of the evaluations.

Map of debris flows caused by rainfall during 1996 in parts of the Reedsport and Deer Head Point quadrangles, Douglas County, southern Coast Range, Oregon

USGS Publications Warehouse

Coe, Jeffrey A.; Michael, John A.; Burgos, Marianela Mercado

2011-01-01

This 1:12,000-scale map shows an inventory of debris flows caused by rainfall during 1996 in a 94.4 km2 area in the southern Coast Range of Oregon. This map and associated digital data are part of a larger U.S. Geological Survey study of debris flows in the southern Coast Range. Available evidence indicates that the flows were triggered by a rain storm that occurred between November 17 and 19. The closest rain gage in the Coast Range (Goodwin Peak) recorded 245 mm during the storm. Maximum rainfall intensity during the storm was 13.2 mm/hr on November 18. Debris flows were photogrammetrically mapped from 1:12,000-scale aerial photographs flown in May, 1997. The inventory is presented on imagery derived from LiDAR data acquired in 2008. We classified mapped debris flows into four categories based on the type of debris-flow activity: (1) discrete slide source areas, (2) predominantly erosion, (3) predominantly transport or mixed erosion and deposition, and (4) predominantly deposition. Locations of woody-debris jams are also shown on the map. The area encompassed by debris flows is 2.1 percent of the 94.4 km2 map area.

Forest and range mapping in the Houston area with ERTS-1

NASA Technical Reports Server (NTRS)

Heath, G. R.; Parker, H. D.

1973-01-01

ERTS-1 data acquired over the Houston area has been analyzed for applications to forest and range mapping. In the field of forestry the Sam Houston National Forest (Texas) was chosen as a test site, (Scene ID 1037-16244). Conventional imagery interpretation as well as computer processing methods were used to make classification maps of timber species, condition and land-use. The results were compared with timber stand maps which were obtained from aircraft imagery and checked in the field. The preliminary investigations show that conventional interpretation techniques indicated an accuracy in classification of 63 percent. The computer-aided interpretations made by a clustering technique gave 70 percent accuracy. Computer-aided and conventional multispectral analysis techniques were applied to range vegetation type mapping in the gulf coast marsh. Two species of salt marsh grasses were mapped.

Map of Io Volcanic Heat Flow

NASA Image and Video Library

2015-09-15

This frame from an animation shows Jupiter volcanic moon Io as seen by NASA Voyager and Galileo spacecraft (at left) and the pattern of heat flow from 242 active volcanoes (at right). The red and yellow areas are places where local heat flow is greatest -- the result of magma erupting from Io's molten interior onto the surface. The map is the result of analyzing decades of observations from spacecraft and ground-based telescopes. It shows Io's usual volcanic thermal emission, excluding the occasional massive but transient "outburst" eruption; in other words, this is what Io looks like most of the time. This heat flow map will be used to test models of interior heating. The map shows that areas of enhanced volcanic heat flow are not necessarily correlated with the number of volcanoes in a particular region and are poorly correlated with expected patterns of heat flow from current models of tidal heating -- something that is yet to be explained. This research is published in association with a 2015 paper in the journal Icarus by A. Davies et al., titled "Map of Io's Volcanic Heat Flow," (http://dx.doi.org/10.1016/j.icarus.2015.08.003.) http://photojournal.jpl.nasa.gov/catalog/PIA19655

Malaria Risk Mapping for Control in the Republic of Sudan

PubMed Central

Noor, Abdisalan M.; ElMardi, Khalid A.; Abdelgader, Tarig M.; Patil, Anand P.; Amine, Ahmed A. A.; Bakhiet, Sahar; Mukhtar, Maowia M.; Snow, Robert W.

2012-01-01

Evidence shows that malaria risk maps are rarely tailored to address national control program ambitions. Here, we generate a malaria risk map adapted for malaria control in Sudan. Community Plasmodium falciparum parasite rate (PfPR) data from 2000 to 2010 were assembled and were standardized to 2–10 years of age (PfPR2–10). Space-time Bayesian geostatistical methods were used to generate a map of malaria risk for 2010. Surfaces of aridity, urbanization, irrigation schemes, and refugee camps were combined with the PfPR2–10 map to tailor the epidemiological stratification for appropriate intervention design. In 2010, a majority of the geographical area of the Sudan had risk of < 1% PfPR2–10. Areas of meso- and hyperendemic risk were located in the south. About 80% of Sudan's population in 2011 was in the areas in the desert, urban centers, or where risk was < 1% PfPR2–10. Aggregated data suggest reducing risks in some high transmission areas since the 1960s. PMID:23033400

Ground gamma-ray spectrometric studies of El-Sahu area, southwestern Sinai, Egypt

NASA Astrophysics Data System (ADS)

Abdrabboh, Ahmad M.

2017-12-01

Based on the previous airborne gamma-ray spectrometric study carried out in southwestern Sinai area, El Sahu area was selected for detail ground gamma-ray spectrometric survey. This area is considered as a good target for radioactive mineral exploration. The study area is exposed in a Paleozoic basin covered by different rocks (ranging from Precambrian to Quaternary). The ground gamma-ray spectrometric survey has been conducted along the study area through random survey. The resultant gamma-ray spectrometric maps show different levels of radioactivity over the studied area, which reflect contrasting radioelement contents for the exposed various rock types. The studied area possesses total count ranging from 2.6 to 326 Ur, 0.1 to 2.8% K, 1.7 to 316 ppm eU and 0.9 to 47.5 ppm eTh. The highest uranium concentrations are located in the northern and southern parts of El Sahu area. They are mainly associated with Um Bogma Formation occurrences. Uranium ratio maps (eU/K and eU/eTh) as well as ternary maps show sharp increase of eU content over both potassium and thorium contents associated with the ENE and NNW trends in Um Bogma Formation, indicating an increase in the U-potentiality than the surrounding rocks. This indicates that the mineralization in the study area may be structurally-controlled.

A comparative study on the predictive ability of the decision tree, support vector machine and neuro-fuzzy models in landslide susceptibility mapping using GIS

NASA Astrophysics Data System (ADS)

Pradhan, Biswajeet

2013-02-01

The purpose of the present study is to compare the prediction performances of three different approaches such as decision tree (DT), support vector machine (SVM) and adaptive neuro-fuzzy inference system (ANFIS) for landslide susceptibility mapping at Penang Hill area, Malaysia. The necessary input parameters for the landslide susceptibility assessments were obtained from various sources. At first, landslide locations were identified by aerial photographs and field surveys and a total of 113 landslide locations were constructed. The study area contains 340,608 pixels while total 8403 pixels include landslides. The landslide inventory was randomly partitioned into two subsets: (1) part 1 that contains 50% (4000 landslide grid cells) was used in the training phase of the models; (2) part 2 is a validation dataset 50% (4000 landslide grid cells) for validation of three models and to confirm its accuracy. The digitally processed images of input parameters were combined in GIS. Finally, landslide susceptibility maps were produced, and the performances were assessed and discussed. Total fifteen landslide susceptibility maps were produced using DT, SVM and ANFIS based models, and the resultant maps were validated using the landslide locations. Prediction performances of these maps were checked by receiver operating characteristics (ROC) by using both success rate curve and prediction rate curve. The validation results showed that, area under the ROC curve for the fifteen models produced using DT, SVM and ANFIS varied from 0.8204 to 0.9421 for success rate curve and 0.7580 to 0.8307 for prediction rate curves, respectively. Moreover, the prediction curves revealed that model 5 of DT has slightly higher prediction performance (83.07), whereas the success rate showed that model 5 of ANFIS has better prediction (94.21) capability among all models. The results of this study showed that landslide susceptibility mapping in the Penang Hill area using the three approaches (e.g., DT, SVM and ANFIS) is viable. As far as the performance of the models are concerned, the results appeared to be quite satisfactory, i.e., the zones determined on the map being zones of relative susceptibility.

Map showing general availability of ground water in the Alton-Kolob coal-fields area, Utah

USGS Publications Warehouse

Price, Don

1982-01-01

This is one of a series of maps that describes the geology and related natural resources of the Alton-Kolob coal-fields area, Utah. Shown on this map is the general availability of ground water as indicated by potential yields of individual wells and expected depth to water in wells. Most data used to compile this map were collected by the U.S. Geological Survey in cooperation with the Utah Department of Natural Resources Division of Water Rights. Other sources of data included the U.S. Geological Survey 7½- and 15-minute topographic quadrangle maps, unpublished reports of field evaluations of potential shock-watering sites by U.S. Geological Survey personnel, and the geologic map of Utah (Stokes, 1964).This map is very generalized and is intended chiefly for planning purposes. It should be used with discretion. For more detailed information about the availability of ground water in various parts of the map area the reader is referred to the following reports: Thomas and Taylor (1946); Marine (1963); Sandberg (1963, 1966); Carpenter, Robinson, and Bjorklund (1964, 1967); Feltis (1966); Goode (1964, 1966); Cordova, Sandberg, and McConkie (1972); Cordova (1978, 1981); and Bjorklund, Sumison, and Sandberg (1977, 1978). For a general description of the chemical quality of ground water in the Alton-Kolob coal-fields area the reader is referred to Price (1981).

Integrated study of basins in the Four Corners region

NASA Astrophysics Data System (ADS)

Fagbola, Olamide Olawumi

2007-12-01

This dissertation is an integrated study of basins in the four corners area of the central part of the Colorado Plateau. The Colorado Plateau is a structurally unique part of the Rocky Mountain region because it has only been moderately deformed when compared to the more intensely deformed areas around it. The Colorado Plateau covers a portion of Utah, Colorado, New Mexico and Arizona. The study area extends from latitude 34°N-40°N to longitude 106°W-111W° encompassing a series of major basins and uplifts: the San Juan, Black Mesa, Paradox, and the Blanding basins; and the Zuni, Defiance, Four Corners, Monument uplifts and the San Juan dome and volcanic field. An analysis of gravity anomalies, basement and crustal structure for basins in the four corners region was carried out. This involved using gravity, magnetic, well, outcrop, seismic estimates of crustal thickness, and geologic data in an integrated fashion. Six filtered gravity and three filtered magnetic maps were generated to aid in the interpretation of the gravity and magnetic anomalies in the study area. A detailed comparison of these maps was carried out. The results show a deep seated mafic structure in the basement acting as a crustal boundary separating the high gravity anomalies from the low. These maps also show that the sources of these anomalies are quite shallow resulting from the upper crust in the study area. The structures in the study area are characterized by northwest and northeast trends which correspond to the Precambrian and the Late Paleozoic structures, respectively. A crustal thickness map of the area was also constructed from seismic estimates of crustal thickness. A comparison was done between the crustal thickness map and the 45 km upward continuation Bouguer anomaly map. The result of this comparison shows that areas of thicker ix crust corresponded to low gravity while areas of thinner crust means mantle material is closer to the surface, thereby producing a high gravity anomaly. The thinnest crust encountered is about 32 km while the thickest crust is about 50 km. Seven gravity models were constructed and these include three crustal-scale profiles crisscrossing the study area and four local profiles. The gravity profiles were modeled using well data, structural thickness maps, cross section data, geologic maps and previous gravity models as constraints. Basement inhomogeneities beneath the basins and the uplifts were delineated by the gravity modeling. One of results from this study reveals that the basement beneath the Four Corners area is highly inhomogeneous. This study reveals that there is a high density deep seated mafic intrusion present in the basement which is responsible for the high gravity and magnetic anomaly in A. This dissertation has also shown that the Four Corners region does not possess a single crustal signature as shown by the different crustal trends in San Juan basin trending northeast and the east-west trending Uncompahgre uplift. The 45 km upward continuation gravity map was also found to correlate with seismic estimates of crustal thickness. The Precambrian basement in this region is also not homogeneous as shown by the necessity of inserting exotic bodies into the basement to compensate for high gravity anomalies and lastly an attempt was made to better define Tweto's (1980) outline of geologic features in the study area. On integrating gravity, magnetics, well and outcrop data, the relief of the Defiance uplift is not as high as delineated by Tweto's (1980) outline.

Preliminary photointerpretation map of landslide and other surficial deposits of the Mount Hamilton quadrangle and parts of the Mount Boardman and San Jose quadrangles, Alameda and Santa Clara Counties, California

USGS Publications Warehouse

Nilsen, Tor H.

1972-01-01

This map, then, shows the cumulative effects of various processes that have yielded surficial deposits up to the time the photographs used for photointerpretation were taken. It does not indicate directly areas where processes will be most active, nor does it show the rate at which they will operate. However, knowledge of the history of geologic events is a key to understanding and predicting the evolution of an area, even where man's activities significantly change the character of the land. Almost all new landslides, for example, occur in areas with a history of landslide activity.

Examining geographic patterns of mortality: the atlas of mortality in small areas in Spain (1987-1995).

PubMed

Benach, Joan; Yasui, Yutaka; Borrell, Carme; Rosa, Elisabeth; Pasarín, M Isabel; Benach, Núria; Español, Esther; Martínez, José Miguel; Daponte, Antonio

2003-06-01

Small-area mortality atlases have been demonstrated to be a useful tool for both showing general geographical patterns in mortality data and identifying specific high-risk locations. In Spain no study has so far systematically examined geographic patterns of small-area mortality for the main causes of death. This paper presents the main features, contents and potential uses of the Spanish Atlas of Mortality in small areas (1987-1995). Population data for 2,218 small areas were drawn from the 1991 Census. Aggregated mortality data for 14 specific causes of death for the period 1987-1995 were obtained for each small area. Empirical Bayes-model-based estimates of age-adjusted relative risk were displayed in small-area maps for each cause/gender/age group (0-64 or 65 and over) combination using the same range of values (i.e. septiles) and colour schemes. The 'Spanish Atlas of Mortality' includes multiple choropleth (area-shaded) small-area maps and graphs to answer different questions about the data. The atlas is divided into three main sections. Section 1 includes the methods and comments on the main maps. Section 2 presents a two-page layout for each leading cause of death by gender including 1) a large map with relative risk estimates, 2) a map that indicates high- and low-risk small areas, 3) a graph with median and interquartile range of relative risk estimates for 17 large regions of Spain, and 4) relative-risk maps for two age groups. Section 3 provides specific information on the geographical units of analysis, statistical methods and other supplemental maps. The 'Spanish Atlas of Mortality' is a useful tool for examining geographical patterns of mortality risk and identifying specific high-risk areas. Mortality patterns displayed in the atlas may have important implications for research and social/health policy planning purposes.

Aeromagnetic interpretation and mineral investigations in the Bolu, Canakkale-Karabiga, Demirkoy, Ezine, and Orhaneli areas of northwestern Turkey in 1968

USGS Publications Warehouse

Jacobson, Herbert Samuel; Tumer, Ural; Karahacioglu, Hamit

1972-01-01

This report reviews progress made during 1968 in the continuing Joint Haden Tetkik ve Arama Enstitusu (MSA)-U. S. Geological Survey (USGS) Mineral Exploration and Training Project, Subproject 2. Subproject 2 is concerned with aeromagnetic interpretation of MTA's aeromagnetic surveys, and ground investigations of selected aeromagnetic anomalies. This report includes new aeromagnetic maps for the Bolu, Canakkale-Karabiga, Demirkoy, and Orhaneli areas and reviews ground investigations in five areas. Activities for each area are sunmarized below: 1. Bolu area: The aeromagnetic map shows two belts of anomalies related to regional magnetite-bearing formations and a group of discrete anomalies, some of which may reflect significant concentrations of magnetite. To date three of these anomalies have been checked on the ground and at one a metamorphic rock containing 14 percent magnetite was observed. 2. Canakkale-Karabiga area: Ground checks were made of six aeromagnetic anomalies. At one locality (Cakirly-Koyu) 6 km south of Nazmara Sea a small magnetite deposit was found. The magnetic anomaly over the area is 150 meters long, and about 3 meters deep in the center of the anomaly exposed massive magnetite boulders. 3. Demirkoy area: The aeromagnetic map shows only one significant anomaly which was checked on the ground and found to be caused by minor magnetite at an intrusive contact. 4. Ezine area: A ground survey of 4.5 sq km area was made where magnetite boulders are locally present on the surface. No significant magnetic anomaly or iron mineralization were found. 5. Orhaneli area: The aeromagnetic map o# the area showed regional magnetic anomaly patterns related to magnetite in mafic intrusives, ultramafic rocks, and mafic flow rocks. In addition 16 localized anomalies were identified. Most of these anomalies were checked on the ground but no significant iron deposits were found. The largest deposit found was a one-meter wide magnetite vein. During the 1969 field season further investigation of anomalies in the Bolu and Orhaneli areas is planned.

Diagnostic Ability of Wide-field Retinal Nerve Fiber Layer Maps Using Swept-Source Optical Coherence Tomography for Detection of Preperimetric and Early Perimetric Glaucoma.

PubMed

Lee, Won June; Na, Kyeong Ik; Kim, Young Kook; Jeoung, Jin Wook; Park, Ki Ho

2017-06-01

To evaluate the diagnostic ability of wide-field retinal nerve fiber layer (RNFL) maps with swept-source optical coherence tomography (SS-OCT) for detection of preperimetric (PPG) and early perimetric glaucoma (EG). One hundred eighty-four eyes, including 67 healthy eyes, 43 eyes with PPG, and 74 eyes with EG, were analyzed. Patients underwent a comprehensive ocular examination including red-free RNFL photography, visual field testing and wide-field SS-OCT scanning (DRI-OCT-1 Atlantis; Topcon, Tokyo, Japan). SS-OCT provides a wide-field RNFL thickness map and a SuperPixel map, which are composed of the RNFL deviation map of the peripapillary area and the deviation map of the composition of the ganglion cell layer with the inner plexiform layer and RNFL (GC-IPL+RNFL) in the macular area. The ability to discriminate PPG and EG from healthy eyes was assessed using sensitivity, specificity, and area under the receiver operating characteristic curve (AUC) for all parameters and criteria provided by the wide-field SS-OCT scan. The wide-field RNFL thickness map using SS-OCT showed the highest sensitivity of PPG-diagnostic and EG-diagnostic performance compared with the other SS-OCT criteria based on the internal normative base (93.0 and 97.3%, respectively). Among the SS-OCT continuous parameters, the RFNL thickness of the 7 clock-hour, inferior and inferotemporal macular ganglion cell analyses showed the largest AUC of PPG-diagnostic and EG-diagnostic performance (AUC=0.809 to 0.865). The wide-field RNFL thickness map using SS-OCT performed well in distinguishing eyes with PPG and EG from healthy eyes. In the clinical setting, wide-field RNFL maps of SS-OCT can be useful tools for detection of early-stage glaucoma.

Policy Implications and Suggestions on Administrative Measures of Urban Flood

NASA Astrophysics Data System (ADS)

Lee, S. V.; Lee, M. J.; Lee, C.; Yoon, J. H.; Chae, S. H.

2017-12-01

The frequency and intensity of floods are increasing worldwide as recent climate change progresses gradually. Flood management should be policy-oriented in urban municipalities due to the characteristics of urban areas with a lot of damage. Therefore, the purpose of this study is to prepare a flood susceptibility map by using data mining model and make a policy suggestion on administrative measures of urban flood. Therefore, we constructed a spatial database by collecting relevant factors including the topography, geology, soil and land use data of the representative city, Seoul, the capital city of Korea. Flood susceptibility map was constructed by applying the data mining models of random forest and boosted tree model to input data and existing flooded area data in 2010. The susceptibility map has been validated using the 2011 flood area data which was not used for training. The predictor importance value of each factor to the results was calculated in this process. The distance from the water, DEM and geology showed a high predictor importance value which means to be a high priority for flood preparation policy. As a result of receiver operating characteristic (ROC), random forest model showed 78.78% and 79.18% accuracy of regression and classification and boosted tree model showed 77.55% and 77.26% accuracy of regression and classification, respectively. The results show that the flood susceptibility maps can be applied to flood prevention and management, and it also can help determine the priority areas for flood mitigation policy by providing useful information to policy makers.

Prior-knowledge-based spectral mixture analysis for impervious surface mapping

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Jinshui; He, Chunyang; Zhou, Yuyu

2014-01-03

In this study, we developed a prior-knowledge-based spectral mixture analysis (PKSMA) to map impervious surfaces by using endmembers derived separately for high- and low-density urban regions. First, an urban area was categorized into high- and low-density urban areas, using a multi-step classification method. Next, in high-density urban areas that were assumed to have only vegetation and impervious surfaces (ISs), the Vegetation-Impervious model (V-I) was used in a spectral mixture analysis (SMA) with three endmembers: vegetation, high albedo, and low albedo. In low-density urban areas, the Vegetation-Impervious-Soil model (V-I-S) was used in an SMA analysis with four endmembers: high albedo, lowmore » albedo, soil, and vegetation. The fraction of IS with high and low albedo in each pixel was combined to produce the final IS map. The root mean-square error (RMSE) of the IS map produced using PKSMA was about 11.0%, compared to 14.52% using four-endmember SMA. Particularly in high-density urban areas, PKSMA (RMSE = 6.47%) showed better performance than four-endmember (15.91%). The results indicate that PKSMA can improve IS mapping compared to traditional SMA by using appropriately selected endmembers and is particularly strong in high-density urban areas.« less

Radon potential mapping of the Tralee-Castleisland and Cavan areas (Ireland) based on airborne gamma-ray spectrometry and geology.

PubMed

Appleton, J D; Doyle, E; Fenton, D; Organo, C

2011-06-01

The probability of homes in Ireland having high indoor radon concentrations is estimated on the basis of known in-house radon measurements averaged over 10 km × 10 km grid squares. The scope for using airborne gamma-ray spectrometer data for the Tralee-Castleisland area of county Kerry and county Cavan to predict the radon potential (RP) in two distinct areas of Ireland is evaluated in this study. Airborne data are compared statistically with in-house radon measurements in conjunction with geological and ground permeability data to establish linear regression models and produce radon potential maps. The best agreement between the percentage of dwellings exceeding the reference level (RL) for radon concentrations in Ireland (% > RL), estimated from indoor radon data, and modelled RP in the Tralee-Castleisland area is produced using models based on airborne gamma-ray spectrometry equivalent uranium (eU) and ground permeability data. Good agreement was obtained between the % > RL from indoor radon data and RP estimated from eU data in the Cavan area using terrain specific models. In both areas, RP maps derived from eU data are spatially more detailed than the published 10 km grid map. The results show the potential for using airborne radiometric data for producing RP maps.

Global seafloor geomorphic features map: applications for ocean conservation and management

NASA Astrophysics Data System (ADS)

Harris, P. T.; Macmillan-Lawler, M.; Rupp, J.; Baker, E.

2013-12-01

Seafloor geomorphology, mapped and measured by marine scientists, has proven to be a very useful physical attribute for ocean management because different geomorphic features (eg. submarine canyons, seamounts, spreading ridges, escarpments, plateaus, trenches etc.) are commonly associated with particular suites of habitats and biological communities. Although we now have better bathymetric datasets than ever before, there has been little effort to integrate these data to create an updated map of seabed geomorphic features or habitats. Currently the best available global seafloor geomorphic features map is over 30 years old. A new global seafloor geomorphic features map (GSGM) has been created based on the analysis and interpretation of the SRTM (Shuttle Radar Topography Mission) 30 arc-second (~1 km) global bathymetry grid. The new map includes global spatial data layers for 29 categories of geomorphic features, defined by the International Hydrographic Organisation. The new geomorphic features map will allow: 1) Characterization of bioregions in terms of their geomorphic content (eg. GOODS bioregions, Large Marine Ecosystems (LMEs), ecologically or biologically significant areas (EBSA)); 2) Prediction of the potential spatial distribution of vulnerable marine ecosystems (VME) and marine genetic resources (MGR; eg. associated with hydrothermal vent communities, shelf-incising submarine canyons and seamounts rising to a specified depth); and 3) Characterization of national marine jurisdictions in terms of their inventory of geomorphic features and their global representativeness of features. To demonstrate the utility of the GSGM, we have conducted an analysis of the geomorphic feature content of the current global inventory of marine protected areas (MPAs) to assess the extent to which features are currently represented. The analysis shows that many features have very low representation, for example fans and rises have less than 1 per cent of their total area inside existing protected areas. The ';best' represented features, trenches and troughs, have only 8.7 and 5.9 per cent respectively of their total area inside existing protected areas. Seamounts have only 2.8% of their area within existing MPAs. Diagram showing the hierarchy of geomorphic features mapped in the present study. Base layer features are the shelf, slope, abyss and hadal zones. The occurrence of some features is confined to one of the base layers, whereas the occurrence of other features is confined to two or more base layers, as illustrated by shading. Basins and sills are the only features that occur over all four base layers.

Canopy Density Mapping on Ultracam-D Aerial Imagery in Zagros Woodlands, Iran

NASA Astrophysics Data System (ADS)

Erfanifard, Y.; Khodaee, Z.

2013-09-01

Canopy density maps express different characteristics of forest stands, especially in woodlands. Obtaining such maps by field measurements is so expensive and time-consuming. It seems necessary to find suitable techniques to produce these maps to be used in sustainable management of woodland ecosystems. In this research, a robust procedure was suggested to obtain these maps by very high spatial resolution aerial imagery. It was aimed to produce canopy density maps by UltraCam-D aerial imagery, newly taken in Zagros woodlands by Iran National Geographic Organization (NGO), in this study. A 30 ha plot of Persian oak (Quercus persica) coppice trees was selected in Zagros woodlands, Iran. The very high spatial resolution aerial imagery of the plot purchased from NGO, was classified by kNN technique and the tree crowns were extracted precisely. The canopy density was determined in each cell of different meshes with different sizes overlaid on the study area map. The accuracy of the final maps was investigated by the ground truth obtained by complete field measurements. The results showed that the proposed method of obtaining canopy density maps was efficient enough in the study area. The final canopy density map obtained by a mesh with 30 Ar (3000 m2) cell size had 80% overall accuracy and 0.61 KHAT coefficient of agreement which shows a great agreement with the observed samples. This method can also be tested in other case studies to reveal its capability in canopy density map production in woodlands.

A study of the utilization of ERTS-1 data from the Wabash River Basin

NASA Technical Reports Server (NTRS)

Landgrebe, D. A. (Principal Investigator)

1974-01-01

The author has identified the following significant results. The identification and area estimation of crops experiment tested the usefulness of ERTS data for crop survey and produced results indicating that crop statistics could be obtained from ERTS imagery. Soil association mapping results showed that strong relationships exist between ERTS data derived maps and conventional soil maps. Urban land use analysis experiment results indicate potential for accurate gross land use mapping. Water resources mapping demonstrated the feasibility of mapping water bodies using ERTS imagery.

130. ARAII Administration building (ARA613) vicinity map and plot plan ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

130. ARA-II Administration building (ARA-613) vicinity map and plot plan showing relationship to other existing buildings on site and to ARA-602, to which this building was attached. F.C. Torkelson Comapny 842-area/SL-1-101-U-1. Date: October 1959. Ineel index code no. 070-0101-65-851-150053. - Idaho National Engineering Laboratory, Army Reactors Experimental Area, Scoville, Butte County, ID

Map of Ceres' Bright Spots

NASA Image and Video Library

2017-12-12

This map from NASA's Dawn mission shows locations of bright material on dwarf planet Ceres. There are more than 300 bright areas, called "faculae," on Ceres. Scientists have divided them into four categories: bright areas on the floors of crater (red), on the rims or walls of craters (green), in the ejecta blankets of craters (blue), and on the flanks of the mountain Ahuna Mons (yellow). https://photojournal.jpl.nasa.gov/catalog/PIA21914

The influence of land use change on landslide susceptibility zonation: the Briga catchment test site (Messina, Italy).

PubMed

Reichenbach, P; Busca, C; Mondini, A C; Rossi, M

2014-12-01

The spatial distribution of landslides is influenced by different climatic conditions and environmental settings including topography, morphology, hydrology, lithology, and land use. In this work, we have attempted to evaluate the influence of land use change on landslide susceptibility (LS) for a small study area located in the southern part of the Briga catchment, along the Ionian coast of Sicily (Italy). On October 1, 2009, the area was hit by an intense rainfall event that triggered abundant slope failures and resulted in widespread erosion. After the storm, an inventory map showing the distribution of pre-event and event landslides was prepared for the area. Moreover, two different land use maps were developed: the first was obtained through a semi-automatic classification of digitized aerial photographs acquired in 1954, the second through the combination of supervised classifications of two recent QuickBird images. Exploiting the two land use maps and different land use scenarios, LS zonations were prepared through multivariate statistical analyses. Differences in the susceptibility models were analyzed and quantified to evaluate the effects of land use change on the susceptibility zonation. Susceptibility maps show an increase in the areal percentage and number of slope units classified as unstable related to the increase in bare soils to the detriment of forested areas.

Landslide susceptibility mapping using a bivariate statistical model in a tropical hilly area of southeastern Brazil

NASA Astrophysics Data System (ADS)

Araújo, J. P. C.; DA Silva, L. M.; Dourado, F. A. D.; Fernandes, N.

2015-12-01

Landslides are the most damaging natural hazard in the mountainous region of Rio de Janeiro State in Brazil, responsible for thousands of deaths and important financial and environmental losses. However, this region has currently few landslide susceptibility maps implemented on an adequate scale. Identification of landslide susceptibility areas is fundamental in successful land use planning and management practices to reduce risk. This paper applied the Bayes' theorem based on weight of evidence (WoE) using 8 landslide-related factors in a geographic information system (GIS) for landslide susceptibility mapping. 378 landslide locations were identified and mapped on a selected basin in the city of Nova Friburgo, triggered by the January 2011 rainfall event. The landslide scars were divided into two subsets: training and validation subsets. The 8 landslide-related factors weighted by WoE were performed using chi-square test to indicate which variables are conditionally independent of each other to be used in the final map. Finally, the maps of weighted factors were summed up to construct the landslide susceptibility map and validated by the validation landslide subset. According to the results, slope, aspect and contribution area showed the higher positive spatial correlation with landslides. In the landslide susceptibility map, 21% of the area presented very low and low susceptibilities with 3% of the validation scars, 41% presented medium susceptibility with 22% of the validation scars and 38% presented high and very high susceptibilities with 75% of the validation scars. The very high susceptibility class stands for 16% of the basin area and has 54% of the all scars. The approach used in this study can be considered very useful since 75% of the area affected by landslides was included in the high and very high susceptibility classes.

A comparison of the IGBP DISCover and University of Maryland 1 km global land cover products

USGS Publications Warehouse

Hansen, M.C.; Reed, B.

2000-01-01

Two global 1 km land cover data sets derived from 1992-1993 Advanced Very High Resolution Radiometer (AVHRR) data are currently available, the International Geosphere-Biosphere Programme Data and Information System (IGBP-DIS) DISCover and the University of Maryland (UMd) 1 km land cover maps. This paper makes a preliminary comparison of the methodologies and results of the two products. The DISCover methodology employed an unsupervised clustering classification scheme on a per-continent basis using 12 monthly maximum NDVI composites as inputs. The UMd approach employed a supervised classification tree method in which temporal metrics derived from all AVHRR bands and the NDVI were used to predict class membership across the entire globe. The DISCover map uses the IGBP classification scheme, while the UMd map employs a modified IGBP scheme minus the classes of permanent wetlands, cropland/natural vegetation mosaic and ice and snow. Global area totals of aggregated vegetation types are very similar and have a per-pixel agreement of 74%. For tall versus short/no vegetation, the per-pixel agreement is 84%. For broad vegetation types, core areas map similarly, while transition zones around core areas differ significantly. This results in high regional variability between the maps. Individual class agreement between the two 1 km maps is 49%. Comparison of the maps at a nominal 0.5 resolution with two global ground-based maps shows an improvement of thematic concurrency of 46% when viewing average class agreement. The absence of the cropland mosaic class creates a difficulty in comparing the maps, due to its significant extent in the DISCover map. The DISCover map, in general, has more forest, while the UMd map has considerably more area in the intermediate tree cover classes of woody savanna/ woodland and savanna/wooded grassland.

Grid-based mapping: A method for rapidly determining the spatial distributions of small features over very large areas

NASA Astrophysics Data System (ADS)

Ramsdale, Jason D.; Balme, Matthew R.; Conway, Susan J.; Gallagher, Colman; van Gasselt, Stephan A.; Hauber, Ernst; Orgel, Csilla; Séjourné, Antoine; Skinner, James A.; Costard, Francois; Johnsson, Andreas; Losiak, Anna; Reiss, Dennis; Swirad, Zuzanna M.; Kereszturi, Akos; Smith, Isaac B.; Platz, Thomas

2017-06-01

The increased volume, spatial resolution, and areal coverage of high-resolution images of Mars over the past 15 years have led to an increased quantity and variety of small-scale landform identifications. Though many such landforms are too small to represent individually on regional-scale maps, determining their presence or absence across large areas helps form the observational basis for developing hypotheses on the geological nature and environmental history of a study area. The combination of improved spatial resolution and near-continuous coverage significantly increases the time required to analyse the data. This becomes problematic when attempting regional or global-scale studies of metre and decametre-scale landforms. Here, we describe an approach for mapping small features (from decimetre to kilometre scale) across large areas, formulated for a project to study the northern plains of Mars, and provide context on how this method was developed and how it can be implemented. Rather than ;mapping; with points and polygons, grid-based mapping uses a ;tick box; approach to efficiently record the locations of specific landforms (we use an example suite of glacial landforms; including viscous flow features, the latitude dependant mantle and polygonised ground). A grid of squares (e.g. 20 km by 20 km) is created over the mapping area. Then the basemap data are systematically examined, grid-square by grid-square at full resolution, in order to identify the landforms while recording the presence or absence of selected landforms in each grid-square to determine spatial distributions. The result is a series of grids recording the distribution of all the mapped landforms across the study area. In some ways, these are equivalent to raster images, as they show a continuous distribution-field of the various landforms across a defined (rectangular, in most cases) area. When overlain on context maps, these form a coarse, digital landform map. We find that grid-based mapping provides an efficient solution to the problems of mapping small landforms over large areas, by providing a consistent and standardised approach to spatial data collection. The simplicity of the grid-based mapping approach makes it extremely scalable and workable for group efforts, requiring minimal user experience and producing consistent and repeatable results. The discrete nature of the datasets, simplicity of approach, and divisibility of tasks, open up the possibility for citizen science in which crowdsourcing large grid-based mapping areas could be applied.

Spirit's Course

NASA Technical Reports Server (NTRS)

2004-01-01

[figure removed for brevity, see original site] [figure removed for brevity, see original site] Figure 1Figure 2

This digital elevation map shows the topography of the 'Columbia Hills,' just in front of the Mars Exploration Rover Spirit's current position. Rover planners have plotted the safest route for Spirit to climb to the front hill, called 'West Spur.' The black line in the middle of the image represents the rover's traverse path, which starts at 'Hank's Hollow' and ends at the top of 'West Spur.' Scientists are sending Spirit up the hill to investigate the interesting rock outcrops visible in images taken by the rover. Data from the Mars Orbital Camera on the orbiting Mars Global Surveyor were used to create this 3-D map.

In figure 1, the digital map shows the slopes of the 'Columbia Hills,' just in front of the Mars Exploration Rover Spirit's current position. Colors indicate the slopes of the hills, with red areas being the gentlest and blue the steepest. Rover planners have plotted the safest route for Spirit to climb the front hill, called 'West Spur.' The path is indicated here with a curved black line. Stereo images from the Mars Orbital Camera on the orbiting Mars Global Surveyor were used to create this 3-D map.

In figure 2, the map shows the north-facing slopes of the 'Columbia Hills,' just in front of the Mars Exploration Rover Spirit's current position. Bright areas indicate surfaces sloping more toward the north than dark areas. To reach the rock outcrop at the top of the hill, engineers will aim to drive the rover around the dark areas, which would yield less solar power. The curved black line in the middle represents the rover's planned traverse path.

An application of adaptive neuro-fuzzy inference system to landslide susceptibility mapping (Klang valley, Malaysia)

NASA Astrophysics Data System (ADS)

Sezer, Ebru; Pradhan, Biswajeet; Gokceoglu, Candan

2010-05-01

Landslides are one of the recurrent natural hazard problems throughout most of Malaysia. Recently, the Klang Valley area of Selangor state has faced numerous landslide and mudflow events and much damage occurred in these areas. However, only little effort has been made to assess or predict these events which resulted in serious damages. Through scientific analyses of these landslides, one can assess and predict landslide-susceptible areas and even the events as such, and thus reduce landslide damages through proper preparation and/or mitigation. For this reason , the purpose of the present paper is to produce landslide susceptibility maps of a part of the Klang Valley areas in Malaysia by employing the results of the adaptive neuro-fuzzy inference system (ANFIS) analyses. Landslide locations in the study area were identified by interpreting aerial photographs and satellite images, supported by extensive field surveys. Landsat TM satellite imagery was used to map vegetation index. Maps of topography, lineaments and NDVI were constructed from the spatial datasets. Seven landslide conditioning factors such as altitude, slope angle, plan curvature, distance from drainage, soil type, distance from faults and NDVI were extracted from the spatial database. These factors were analyzed using an ANFIS to construct the landslide susceptibility maps. During the model development works, total 5 landslide susceptibility models were obtained by using ANFIS results. For verification, the results of the analyses were then compared with the field-verified landslide locations. Additionally, the ROC curves for all landslide susceptibility models were drawn and the area under curve values was calculated. Landslide locations were used to validate results of the landslide susceptibility map and the verification results showed 98% accuracy for the model 5 employing all parameters produced in the present study as the landslide conditioning factors. The validation results showed sufficient agreement between the obtained susceptibility map and the existing data on landslide areas. Qualitatively, the model yields reasonable results which can be used for preliminary land-use planning purposes. As a final conclusion, the results obtained from the study showed that the ANFIS modeling is a very useful and powerful tool for the regional landslide susceptibility assessments. However, the results to be obtained from the ANFIS modeling should be assessed carefully because the overlearning may cause misleading results. To prevent overlerning, the numbers of membership functions of inputs and the number of training epochs should be selected optimally and carefully.

A novel approach for monitoring writing interferences during navigated transcranial magnetic stimulation mappings of writing related cortical areas.

PubMed

Rogić Vidaković, Maja; Gabelica, Dragan; Vujović, Igor; Šoda, Joško; Batarelo, Nikolina; Džimbeg, Andrija; Zmajević Schönwald, Marina; Rotim, Krešimir; Đogaš, Zoran

2015-11-30

It has recently been shown that navigated repetitive transcranial magnetic stimulation (nTMS) is useful in preoperative neurosurgical mapping of motor and language brain areas. In TMS mapping of motor cortices the evoked responses can be quantitatively monitored by electromyographic (EMG) recordings. No such setup exists for monitoring of writing during nTMS mappings of writing related cortical areas. We present a novel approach for monitoring writing during nTMS mappings of motor writing related cortical areas. To our best knowledge, this is the first demonstration of quantitative monitoring of motor evoked responses from hand by EMG, and of pen related activity during writing with our custom made pen, together with the application of chronometric TMS design and patterned protocol of rTMS. The method was applied in four healthy subjects participating in writing during nTMS mapping of the premotor cortical area corresponding to BA 6 and close to the superior frontal sulcus. The results showed that stimulation impaired writing in all subjects. The corresponding spectra of measured signal related to writing movements was observed in the frequency band 0-20 Hz. Magnetic stimulation affected writing by suppressing normal writing frequency band. The proposed setup for monitoring of writing provides additional quantitative data for monitoring and the analysis of rTMS induced writing response modifications. The setup can be useful for investigation of neurophysiologic mechanisms of writing, for therapeutic effects of nTMS, and in preoperative mapping of language cortical areas in patients undergoing brain surgery. Copyright © 2015 Elsevier B.V. All rights reserved.

NASA-Produced Map Shows Extent of Southern California Wildfire Damage

NASA Image and Video Library

2017-12-14

The Advanced Rapid Imaging and Analysis (ARIA) team at NASA's Jet Propulsion Laboratory in Pasadena, California, and Caltech, also in Pasadena, created a Damage Proxy Map (DPM) depicting areas in Southern California that are likely damaged (shown by red and yellow pixels) as a result of recent wildfires, including the Thomas Fire in Ventura and Santa Barbara Counties, highlighted in the attached image taken from the DPM. The map is derived from synthetic aperture radar (SAR) images from the Copernicus Sentinel-1 satellites, operated by the European Space Agency (ESA). The images were taken before (Nov. 28, 2017, 6 a.m. PST) and after (Dec. 10, 2017, 6 a.m. PST) the onset of the fires. The map covers an area of 107 by 107 miles (172 by 172 kilometers), shown by the large red polygon. Each pixel measures about 33 yards (30 meters) across. The color variation from yellow to red indicates increasingly more significant ground surface change. Preliminary validation was done by comparing the map to optical satellite imagery from DigitalGlobe. This damage proxy map should be used as guidance to identify damaged areas, and may be less reliable over vegetated areas. For example, the colored pixels seen over mountainous areas may seem a little scattered even though the reality could be that the contiguous areas were burned. Patches of farmland can also appear as signals due to plowing or irrigation. The full map is available to download from https://aria-share.jpl.nasa.gov/events/20171210-SoCal_Fire/. https://photojournal.jpl.nasa.gov/catalog/PIA22191

An integrated approach of analytical network process and fuzzy based spatial decision making systems applied to landslide risk mapping

NASA Astrophysics Data System (ADS)

Abedi Gheshlaghi, Hassan; Feizizadeh, Bakhtiar

2017-09-01

Landslides in mountainous areas render major damages to residential areas, roads, and farmlands. Hence, one of the basic measures to reduce the possible damage is by identifying landslide-prone areas through landslide mapping by different models and methods. The purpose of conducting this study is to evaluate the efficacy of a combination of two models of the analytical network process (ANP) and fuzzy logic in landslide risk mapping in the Azarshahr Chay basin in northwest Iran. After field investigations and a review of research literature, factors affecting the occurrence of landslides including slope, slope aspect, altitude, lithology, land use, vegetation density, rainfall, distance to fault, distance to roads, distance to rivers, along with a map of the distribution of occurred landslides were prepared in GIS environment. Then, fuzzy logic was used for weighting sub-criteria, and the ANP was applied to weight the criteria. Next, they were integrated based on GIS spatial analysis methods and the landslide risk map was produced. Evaluating the results of this study by using receiver operating characteristic curves shows that the hybrid model designed by areas under the curve 0.815 has good accuracy. Also, according to the prepared map, a total of 23.22% of the area, amounting to 105.38 km2, is in the high and very high-risk class. Results of this research are great of importance for regional planning tasks and the landslide prediction map can be used for spatial planning tasks and for the mitigation of future hazards in the study area.

Right parietal cortex and calculation processing: intraoperative functional mapping of multiplication and addition in patients affected by a brain tumor.

PubMed

Della Puppa, Alessandro; De Pellegrin, Serena; d'Avella, Elena; Gioffrè, Giorgio; Munari, Marina; Saladini, Marina; Salillas, Elena; Scienza, Renato; Semenza, Carlo

2013-11-01

The role of parietal areas in number processing is well known. The significance of intraoperative functional mapping of these areas has been only partially explored, however, and only a few discordant data are available in the surgical literature with regard to the right parietal lobe. The purpose of this study was to evaluate the clinical impact of simple calculation in cortical electrostimulation of right-handed patients affected by a right parietal brain tumor. Calculation mapping in awake surgery was performed in 3 right-handed patients affected by high-grade gliomas located in the right parietal lobe. Preoperatively, none of the patients presented with calculation deficits. In all 3 cases, after sensorimotor and language mapping, cortical and intraparietal sulcus areas involved in single-digit multiplication and addition calculations were mapped using bipolar electrostimulation. In all patients, different sites of the right parietal cortex, mainly in the inferior lobule, were detected as being specifically related to calculation (multiplication or addition). In 2 patients the intraparietal sulcus was functionally specific for multiplication. No functional sites for language were detected. All sites functional for calculation were spared during tumor resection, which was complete in all cases without postoperative neurological deficits. These findings provide intraoperative data in support of an anatomofunctional organization for multiplication and addition within the right parietal area. Furthermore, the study shows the potential clinical relevance of intraoperative mapping of calculation in patients undergoing surgery in the right parietal area. Further and larger studies are needed to confirm these data and assess whether mapped areas are effectively essential for function.

A Method of Spatial Mapping and Reclassification for High-Spatial-Resolution Remote Sensing Image Classification

PubMed Central

Wang, Guizhou; Liu, Jianbo; He, Guojin

2013-01-01

This paper presents a new classification method for high-spatial-resolution remote sensing images based on a strategic mechanism of spatial mapping and reclassification. The proposed method includes four steps. First, the multispectral image is classified by a traditional pixel-based classification method (support vector machine). Second, the panchromatic image is subdivided by watershed segmentation. Third, the pixel-based multispectral image classification result is mapped to the panchromatic segmentation result based on a spatial mapping mechanism and the area dominant principle. During the mapping process, an area proportion threshold is set, and the regional property is defined as unclassified if the maximum area proportion does not surpass the threshold. Finally, unclassified regions are reclassified based on spectral information using the minimum distance to mean algorithm. Experimental results show that the classification method for high-spatial-resolution remote sensing images based on the spatial mapping mechanism and reclassification strategy can make use of both panchromatic and multispectral information, integrate the pixel- and object-based classification methods, and improve classification accuracy. PMID:24453808

The Effect of Shadow Area on Sgm Algorithm and Disparity Map Refinement from High Resolution Satellite Stereo Images

NASA Astrophysics Data System (ADS)

Tatar, N.; Saadatseresht, M.; Arefi, H.

2017-09-01

Semi Global Matching (SGM) algorithm is known as a high performance and reliable stereo matching algorithm in photogrammetry community. However, there are some challenges using this algorithm especially for high resolution satellite stereo images over urban areas and images with shadow areas. As it can be seen, unfortunately the SGM algorithm computes highly noisy disparity values for shadow areas around the tall neighborhood buildings due to mismatching in these lower entropy areas. In this paper, a new method is developed to refine the disparity map in shadow areas. The method is based on the integration of potential of panchromatic and multispectral image data to detect shadow areas in object level. In addition, a RANSAC plane fitting and morphological filtering are employed to refine the disparity map. The results on a stereo pair of GeoEye-1 captured over Qom city in Iran, shows a significant increase in the rate of matched pixels compared to standard SGM algorithm.

Ground-water levels in the alluvial aquifer at Louisville, Kentucky, 1982-87

USGS Publications Warehouse

Faust, R.J.; Lyverse, M.A.

1987-01-01

Water level data have been collected in the alluvial aquifer at Louisville, Kentucky by the U.S. Geological Survey since 1943. Interpretations of these data have been published in several reports by the Survey, but none have been published since 1983. Contour maps and hydrographs are presented in this report to document and to help interpret water level changes for the period 1982-87. Maps and hydrographs show that groundwater levels generally stabilized in the 1980 's after rising for many years. Two areas of groundwater withdrawals are apparent in the maps and hydrographs. Withdrawals in an industrial area in west Louisville disrupt the typical pattern of the contours to curve landward around the area of withdrawal. Resumption of pumping of groundwater for heating and cooling of some buildings in the downtown area in 1985 caused declines of about 3 to 4 ft in the downtown area. (Author 's abstract)

Fusiform-Rust-Hazard Maps for Loblolly and Slash Pines

Treesearch

Robert L. Anderson; Thomas C. McCartney; Noel D. Cost; Hugh Devine; Martin Botkin

1988-01-01

Rust-hazard saps made from Forest Inventory and Analysis plot data show that fusiform rust on slash pine is most common in north-central Florida, in southeastern Georgia, and in areas north of slash pine's natural range. On loblolly pine, the disease is most common in central and southeastern Georgia and in portions of South Carolina. These maps show the general...

Mapping flood and flooding potential indices: a methodological approach to identifying areas susceptible to flood and flooding risk. Case study: the Prahova catchment (Romania)

NASA Astrophysics Data System (ADS)

Zaharia, Liliana; Costache, Romulus; Prăvălie, Remus; Ioana-Toroimac, Gabriela

2017-04-01

Given that floods continue to cause yearly significant worldwide human and material damages, flood risk mitigation is a key issue and a permanent challenge in developing policies and strategies at various spatial scales. Therefore, a basic phase is elaborating hazard and flood risk maps, documents which are an essential support for flood risk management. The aim of this paper is to develop an approach that allows for the identification of flash-flood and flood-prone susceptible areas based on computing and mapping of two indices: FFPI (Flash-Flood Potential Index) and FPI (Flooding Potential Index). These indices are obtained by integrating in a GIS environment several geographical variables which control runoff (in the case of the FFPI) and favour flooding (in the case of the FPI). The methodology was applied in the upper (mountainous) and middle (hilly) catchment of the Prahova River, a densely populated and socioeconomically well-developed area which has been affected repeatedly by water-related hazards over the past decades. The resulting maps showing the spatialization of the FFPI and FPI allow for the identification of areas with high susceptibility to flashfloods and flooding. This approach can provide useful mapped information, especially for areas (generally large) where there are no flood/hazard risk maps. Moreover, the FFPI and FPI maps can constitute a preliminary step for flood risk and vulnerability assessment.

Map showing the potentiometric surface of the Magothy Aquifer in southern Maryland, September 1982

USGS Publications Warehouse

Mack, Frederick K.; Wheeler, Judith C.; Curtin, Stephen E.

1982-01-01

A map was prepared that shows the potentiometric surface of the Magothy aquifer in southern Maryland in September 1982. The map is based on measurements from a network of 83 observation wells. The highest levels of the potentiometric surface, 57 and 58 feet above sea level, were measured near the outcrop-subcrop of the aquifer in topographically high areas of Anne Arundel and Prince Georges Counties. The potentiometric surface slopes to the southeast to about sea level along much of the western shore of the Chesapeake Bay. Three distinct and extensive cones of depression have developed in the potentiometric surface around the well fields of the Annapolis area, Waldorf area, and Chalk Point. Several square miles of each cone are below sea level, and in some areas at Chalk Point and Waldorf, the cone is more than 50 feet below sea level. The network of wells was developed as part of the cooperative program between the U.S. Geological Survey, the Maryland Geological Survey, and the Maryland Energy Administration. (USGS)

Geologic map of the Lassen Peak, Chaos Crags, and Upper Hat Creek area, California

USGS Publications Warehouse

Christiansen, Robert L.; Clynne, Michael A.; Muffler, L.J. Patrick

2002-01-01

This digital publication contains all the information used to publish U.S. Geological Survey Geologic Investigations Series I-2723 (Christiansen and others, 2002). The map shows the distribution and relationships of volcanic and surficial-sedimentary deposits in an area of Lassen Volcanic National Park and vicinity. Emphasis is on products of the 1914-1917 eruptions of Lassen Peak and the approximately 1000-year-old eruptions of Chaos Crags. ArcInfo grids were prepared from scanned composite images of four U.S. Geological Survey 7.5' topographic quadrangle maps and were georeferenced and reprojected.

Infrared thermal remote sensing for soil salinity assessment on landscape scale

NASA Astrophysics Data System (ADS)

Ivushkin, Konstantin; Bartholomeus, Harm; Bregt, Arnold K.; Pulatov, Alim; Bui, Elisabeth N.; Wilford, John

2017-04-01

Soil salinity is considered as one of the most severe land degradation aspects. An increased soil salt level inhibits growth and development of crops. Therefore, up to date soil salinity information is vital for appropriate management practices and reclamation strategies. This information is required at increasing spatial and temporal resolution for appropriate management adaptations. Conventional soil sampling and associated laboratory analyses are slow, expensive, and often cannot deliver the temporal and spatial resolution required. The change of canopy temperature is one of the stress indicators in plants. Its behaviour in response to salt stress on individual plant level is well studied in laboratory and greenhouse experiments, but its potential for landscape scale studies using remote sensing techniques is not investigated yet. In our study, possibilities of satellite thermography for landscape scale soil salinity assessment of cropped areas were studied. The performance of satellite thermography is compared with other approaches that have been used before, like Normalised Difference Vegetation Index (NDVI) and Enhanced Vegetation Index (EVI). The study areas were Syrdarya province of Uzbekistan and four study areas in four Australian states namely, Western Australia, South Australia, Queensland and New South Wales. The diversity of the study areas allowed us to analyse behaviour of canopy temperature of different crops (wheat, cotton, barley) and different agriculture practices (rain fed and irrigated). MODIS and Landsat TM multiannual satellite images were used to measure canopy temperature. As ground truth for Uzbekistan study area we used a provincial soil salinity map. For the Australian study areas we used the EC map for the whole country. ANOVA was used to analyse relations between the soil salinity maps and canopy temperature, NDVI, EVI. Time series graphs were created to analyse the dynamics of the indicators during the growing season. The results showed significant relations between the soil salinity maps and canopy temperature. The amplitude of canopy temperature difference between salinity classes varies for different crops, but the trend of temperature increase under increased salinity is present in all cases. The calculated F-values were higher for canopy temperature than for all other compared indicators. The vegetation indices also showed significant differences, but F-values were lower compared to canopy temperature. Also the visual comparison of the soil salinity map and the canopy temperature map show similar spatial patterns. The NDVI and EVI maps look more random and noisy and patterns are less pronounced than for the canopy temperature map. The strongest relation between the soil salinity map and canopy temperature was usually observed at the end of a dry season and in the period of maximum crop development. Satellite thermography appeared to be a valuable approach to detect soil salinity under agricultural crops at landscape scale.

Surface Temperature Anomalies Derived from Night Time ASTER Data Corrected for Solar and Topographic Effects, Archuleta County

DOE Data Explorer

Khalid Hussein

2012-02-01

This map shows areas of anomalous surface temperature in Alamosa and Saguache Counties identified from ASTER thermal data and spatial based insolation model. The temperature is calculated using the Emissivity Normalization Algorithm that separate temperature from emissivity. The incoming solar radiation was calculated using spatial based insolation model developed by Fu and Rich (1999). Then the temperature due to solar radiation was calculated using emissivity derived from ASTER data. The residual temperature, i.e. temperature due to solar radiation subtracted from ASTER temperature was used to identify thermally anomalous areas. Areas that had temperature greater than 2o were considered ASTER modeled "very warm modeled surface temperature" are shown in red on the map. Areas that had temperatures between 1o and 2o were considered ASTER modeled "warm modeled surface temperature" are shown in yellow on the map. This map also includes the locations of shallow temperature survey points, locations of springs or wells with favorable geochemistry, faults, transmission lines, and areas of modeled basement weakness "fairways." Note: 'o' is used in this description to represent lowercase sigma.

Surface Temperature Anomalies Derived from Night Time ASTER Data Corrected for Solar and Topographic Effects, San Miguel County, Colorado

DOE Data Explorer

Khalid Hussein

2012-02-01

This map shows areas of anomalous surface temperature in Alamosa and Saguache Counties identified from ASTER thermal data and spatial based insolation model. The temperature is calculated using the Emissivity Normalization Algorithm that separate temperature from emissivity. The incoming solar radiation was calculated using spatial based insolation model developed by Fu and Rich (1999). Then the temperature due to solar radiation was calculated using emissivity derived from ASTER data. The residual temperature, i.e. temperature due to solar radiation subtracted from ASTER temperature was used to identify thermally anomalous areas. Areas that had temperature greater than 2o were considered ASTER modeled "very warm modeled surface temperature" are shown in red on the map. Areas that had temperatures between 1o and 2o were considered ASTER modeled "warm modeled surface temperature" are shown in yellow on the map. This map also includes the locations of shallow temperature survey points, locations of springs or wells with favorable geochemistry, faults, transmission lines, and areas of modeled basement weakness "fairways." Note: 'o' is used in this description to represent lowercase sigma.

Surface Temperature Anomalies Derived from Night Time ASTER Data Corrected for Solar and Topographic Effects, Fremont County, Colorado

DOE Data Explorer

Khalid Hussein

2012-02-01

This map shows areas of anomalous surface temperature in Alamosa and Saguache Counties identified from ASTER thermal data and spatial based insolation model. The temperature is calculated using the Emissivity Normalization Algorithm that separate temperature from emissivity. The incoming solar radiation was calculated using spatial based insolation model developed by Fu and Rich (1999). Then the temperature due to solar radiation was calculated using emissivity derived from ASTER data. The residual temperature, i.e. temperature due to solar radiation subtracted from ASTER temperature was used to identify thermally anomalous areas. Areas that had temperature greater than 2o were considered ASTER modeled "very warm modeled surface temperature" are shown in red on the map. Areas that had temperatures between 1o and 2o were considered ASTER modeled "warm modeled surface temperature" are shown in yellow on the map. This map also includes the locations of shallow temperature survey points, locations of springs or wells with favorable geochemistry, faults, transmission lines, and areas of modeled basement weakness "fairways." Note: 'o' is used in this description to represent lowercase sigma.

Surface Temperature Anomalies Derived from Night Time ASTER Data Corrected for Solar and Topographic Effects, Routt County, Colorado

DOE Data Explorer

Khalid Hussein

2012-02-01

This map shows areas of anomalous surface temperature in Alamosa and Saguache Counties identified from ASTER thermal data and spatial based insolation model. The temperature is calculated using the Emissivity Normalization Algorithm that separate temperature from emissivity. The incoming solar radiation was calculated using spatial based insolation model developed by Fu and Rich (1999). Then the temperature due to solar radiation was calculated using emissivity derived from ASTER data. The residual temperature, i.e. temperature due to solar radiation subtracted from ASTER temperature was used to identify thermally anomalous areas. Areas that had temperature greater than 2o were considered ASTER modeled "very warm modeled surface temperature" are shown in red on the map. Areas that had temperatures between 1o and 2o were considered ASTER modeled"warm modeled surface temperature" are shown in yellow on the map. This map also includes the locations of shallow temperature survey points, locations of springs or wells with favorable geochemistry, faults, transmission lines, and areas of modeled basement weakness "fairways." Note: 'o' is used in this description to represent lowercase sigma.

Surface Temperature Anomalies Derived from Night Time ASTER Data Corrected for Solar and Topographic Effects, Alamosa and Saguache Counties, Colorado

DOE Data Explorer

Khalid Hussein

2012-02-01

This map shows areas of anomalous surface temperature in Alamosa and Saguache Counties identified from ASTER thermal data and spatial based insolation model. The temperature is calculated using the Emissivity Normalization Algorithm that separate temperature from emissivity. The incoming solar radiation was calculated using spatial based insolation model developed by Fu and Rich (1999). Then the temperature due to solar radiation was calculated using emissivity derived from ASTER data. The residual temperature, i.e. temperature due to solar radiation subtracted from ASTER temperature was used to identify thermally anomalous areas. Areas that had temperature greater than 2o were considered ASTER modeled "very warm modeled surface temperature" are shown in red on the map. Areas that had temperatures between 1o and 2o were considered ASTER modeled "warm modeled surface temperature" are shown in yellow on the map. This map also includes the locations of shallow temperature survey points, locations of springs or wells with favorable geochemistry, faults, transmission lines, and areas of modeled basement weakness "fairways." Note: 'o' is used in this description to represent lowercase sigma.

Surface Temperature Anomalies Derived from Night Time ASTER Data Corrected for Solar and Topographic Effects, Dolores County

DOE Data Explorer

Khalid Hussein

2012-02-01

This map shows areas of anomalous surface temperature in Alamosa and Saguache Counties identified from ASTER thermal data and spatial based insolation model. The temperature is calculated using the Emissivity Normalization Algorithm that separate temperature from emissivity. The incoming solar radiation was calculated using spatial based insolation model developed by Fu and Rich (1999). Then the temperature due to solar radiation was calculated using emissivity derived from ASTER data. The residual temperature, i.e. temperature due to solar radiation subtracted from ASTER temperature was used to identify thermally anomalous areas. Areas that had temperature greater than 2o were considered ASTER modeled "very warm modeled surface temperature" are shown in red on the map. Areas that had temperatures between 1o and 2o were considered ASTER modeled "warm modeled surface temperature" are shown in yellow on the map. This map also includes the locations of shallow temperature survey points, locations of springs or wells with favorable geochemistry, faults, transmission lines, and areas of modeled basement weakness "fairways." Note: 'o' is used in this description to represent lowercase sigma.

Application of ERTS-1 imagery to detecting and mapping modern erosion features and to monitoring erosional changes, in southern Arizona

NASA Technical Reports Server (NTRS)

Morrison, R. B. (Principal Investigator); Cooley, M. E.

1973-01-01

The author has identified the following significant results. The chief results during the reporting period were three 1:1,000,000 scale maps made from one ERTS-1 frame (1085-17330, 16 October 1972) showing: (1) the three most important types of materials in terms of the modern erosion problem: the readily erodible soils, gravel piedmonts and basin-fill areas, and consolidated rocks; (2) alluvial fans (dissected and relatively undissected); and (3) (as an additional bonus) linear structural features. Eight key areas (small parts of the whole study area) were selected for detailed study, and mapping was started in two of them, by interpretation of ultrahigh (U-2 and RB-57) airphotos, supplemented by field studies. In these areas detailed mapping was done not only on the modern erosion phenomena (arroyos, gullies, modern flood plains and terraces, and areas of sheet erosion and deposition), but also other features pertinent to the erosion problem, such as slope-local relief, landforms rock units, soil particle size and erodibility, and classes of vegetative cover.

Mapping of unknown industrial plant using ROS-based navigation mobile robot

NASA Astrophysics Data System (ADS)

Priyandoko, G.; Ming, T. Y.; Achmad, M. S. H.

2017-10-01

This research examines how humans work with teleoperated unmanned mobile robot inspection in industrial plant area resulting 2D/3D map for further critical evaluation. This experiment focuses on two parts, the way human-robot doing remote interactions using robust method and the way robot perceives the environment surround as a 2D/3D perspective map. ROS (robot operating system) as a tool was utilized in the development and implementation during the research which comes up with robust data communication method in the form of messages and topics. RGBD SLAM performs the visual mapping function to construct 2D/3D map using Kinect sensor. The results showed that the mobile robot-based teleoperated system are successful to extend human perspective in term of remote surveillance in large area of industrial plant. It was concluded that the proposed work is robust solution for large mapping within an unknown construction building.

Surficial Geologic Map of the Ashby-Lowell-Sterling-Billerica 11-Quadrangle Area in Northeast-Central Massachusetts

USGS Publications Warehouse

Stone, Byron D.; Stone, Janet R.

2007-01-01

The surficial geologic map shows the distribution of nonlithified earth materials at land surface in an area of eleven 7.5-minute quadrangles (total 505 mi2) in northeast-central Massachusetts. The geologic map differentiates surficial materials of Quaternary age on the basis of their lithologic characteristics (such as grain size and sedimentary structures), constructional geomorphic features, stratigraphic relationships, and age. Surficial earth materials significantly affect human use of the land, and an accurate description of their distribution is particularly important for water resources, construction aggregate resources, earth-surface hazards assessments, and land-use decisions. This compilation of surficial geologic materials is an interim product that defines the areas of exposed bedrock, and the boundaries between glacial till, glacial stratified deposits, and overlying postglacial deposits. This work is part of a comprehensive study to produce a statewide digital map of the surficial geology at a 1:24,000-scale level of accuracy. This report includes explanatory text (PDF), a regional map at 1:50,000 scale (PDF), quadrangle maps at 1:24,000 scale (PDF files), GIS data layers (ArcGIS shapefiles), metadata for the GIS layers, scanned topographic base maps (TIF), and a readme.txt file.

Surficial Geologic Map of the Salem Depot-Newburyport East-Wilmington-Rockport 16-Quadrangle Area in Northeast Massachusetts

USGS Publications Warehouse

Stone, Byron D.; Stone, Janet Radway; DiGiacomo-Cohen, Mary L.

2006-01-01

The surficial geologic map shows the distribution of nonlithified earth materials at land surface in an area of 16 7.5-minute quadrangles (total 658 mi2) in northeast Massachusetts. The geologic map differentiates surficial materials of Quaternary age on the basis of their lithologic characteristics (grain size, sedimentary structures, mineral and rock-particle composition), constructional geomorphic features, stratigraphic relationships, and age. Surficial earth materials significantly affect human use of the land, and an accurate description of their distribution is particularly important for water resources, construction aggregate resources, earth-surface hazards assessments, and land-use decisions. This compilation of surficial geologic materials is an interim product that defines the areas of exposed bedrock, and the boundaries between glacial till, glacial stratified deposits, and overlying postglacial deposits. This work is part of a comprehensive study to produce a statewide digital map of the surficial geology at a 1:24,000-scale level of accuracy. This report includes explanatory text (PDF), a regional map at 1:50,000 scale (PDF), quadrangle maps at 1:24,000 scale (PDF files), GIS data layers (ArcGIS shapefiles), metadata for the GIS layers, scanned topographic base maps (TIF), and a readme.txt file.

Map showing the potential for mineral deposits associated with Precambrian mafic and ultramafic rocks in the Blacktail and Henrys Lake mountains and the Greenhorn and Ruby ranges of southwestern Montana

USGS Publications Warehouse

Hammarstrom, Jane M.; Van Gosen, Bradley S.; Carlson, Robert R.; Kulik, Dolores M.

1998-01-01

In response to requests from the Bureau of Land Management (BLM) and the U.S. Forest Service (USFS), the U.S. Geological Survey (USGS) conducted a mineral resource assessment in the Dillon BLM Resource Area in Beaverhead and Madison Counties, southwestern Montana. These agencies use mineral resource data in creating and updating land-use management plans for federal lands for the reasonably foreseeable future. Mineral resources that have not been developed in the past may be developed in the future, based on changing commodity demands and market conditions. Therefore, federal land managers need geologic information on known mineral occurrences as well as on areas that are permissive for the occurrence of undiscovered mineral resources. This map was prepared to provide this type of geologic information for mineral deposits that can be associated with ultramafic rocks. Areas of exposed Precambrian ultramafic rocks are labeled with uppercase letters (A-F). Sources of geologic maps used to compile this map are shown on the smaller index map ("Index to Geologic Mapping"); lowercase letters (a-m) on the index map are keyed to the reference list.

The use of crop rotation for mapping soil organic content in farmland

NASA Astrophysics Data System (ADS)

Yang, Lin; Song, Min; Zhu, A.-Xing; Qin, Chengzhi

2017-04-01

Most of the current digital soil mapping uses natural environmental covariates. However, human activities have significantly impacted the development of soil properties since half a century, and therefore become an important factor affecting soil spatial variability. Many researches have done field experiments to show how soil properties are impacted and changed by human activities, however, spatial variation data of human activities as environmental covariates have been rarely used in digital soil mapping. In this paper, we took crop rotation as an example of agricultural activities, and explored its effectiveness in characterizing and mapping the spatial variability of soil. The cultivated area of Xuanzhou city and Langxi County in Anhui Province was chosen as the study area. Three main crop rotations,including double-rice, wheat-rice,and oilseed rape-cotton were observed through field investigation in 2010. The spatial distribution of the three crop rotations in the study area was obtained by multi-phase remote sensing image interpretation using a supervised classification method. One-way analysis of variance (ANOVA) for topsoil organic content in the three crop rotation groups was performed. Factor importance of seven natural environmental covariates, crop rotation, Land use and NDVI were generated by variable importance criterion of Random Forest. Different combinations of environmental covariates were selected according to the importance rankings of environmental covariates for predicting SOC using Random Forest and Soil Landscape Inference Model (SOLIM). A cross validation was generated to evaluated the mapping accuracies. The results showed that there were siginificant differences of topsoil organic content among the three crop rotation groups. The crop rotation is more important than parent material, land use or NDVI according to the importance ranking calculated by Random Forest. In addition, crop rotation improved the mapping accuracy, especially for the flat clutivated area. This study demonstrates the usefulness of human activities in digital soil mapping and thus indicates the necessity for human activity factors in digital soil mapping studies.

Potentiometric Surface of the Magothy Aquifer in Southern Maryland, September 2001

USGS Publications Warehouse

Curtin, Stephen E.; Andreasen, David C.; Wheeler, Judith C.

2002-01-01

This report presents a map showing the change in the potentiometric surface of the Aquia aquifer in the Aquia Formation of Paleocene age in Southern Maryland for September 1982 and September 2001. The map, based on water level measurements in 58 wells, shows that the potentiometric surface during the 19-year period declined from zero in the northernmost part of the study area, which is the outcrop of the aquifer, to 120 feet at Lexington Park. Lexington Park is near the southeasternmost part of the study area and approaches the downdip boundary of the aquifer.

Annual summary of ground-water conditions in Arizona, spring 1977 to spring 1978

USGS Publications Warehouse

,

1978-01-01

The withdrawal of ground water was about 5.5 million acre-feet in Arizona in 1977. About 4.7 million acre-feet of ground water was used for the irrigation of crops in 1977. The Salt River Valley and the lower Santa Cruz basin are the largest agricultural areas in the State. For 1973-77, ground-water withdrawal in the two areas was about 8.1 and 5.1 million acre-feet, respectively, and, in general, water levels are declining. Other areas in which ground-water withdrawals have caused water-level declines are the Willcox, San Simon, upper Santa Cruz, Avra Valley, Gila Bend, Harquahala Plains, and McMullen Valley areas. Two small-scale maps of Arizona show (1) pumpage of ground water by areas and (2) the status of the ground-water inventory in the State. The main map, scale 1:500 ,000, shows potential well production, depth to water in selected wells in spring 1978, and change in water level in selected wells from 1973 to 1978. The brief text that accompanies the maps summarizes the current ground-water conditions in the State. (Woodard-USGS)

Annual summary of ground-water conditions in Arizona, spring 1975 to spring 1976

USGS Publications Warehouse

Babcock, H.M.

1977-01-01

Two small-scale maps of Arizona show (1) pumpage of ground water by areas and (2) the status of the ground-water inventory in the State. A larger map of the State at a scale of 1:500,000 shows potential well production, depth to water in selected wells in spring 1976, and change in water level in selected wells from 1971 to 1976. The brief text that accompanies the maps summarizes the current ground-water conditions in the State. The withdrawal of ground water in Arizona was about 5.6 million acre-feet in 1975, of which about 4.7 million acre-feet was used for the irrigation of crops. The Salt River Valley and the lower Santa Cruz basin are the largest agricultural areas in the State. For 1971-75, ground-water withdrawal in the two areas was about 8.3 and 4.7 million acre-feet, respectively, and, in general, water levels are declining. Other areas in which ground-water withdrawals have caused large water-level declines are the Willcox, San Simon, upper Santa Cruz, Avra Valley, Gila Bend, Harquahala Plains, and McMullen Valley areas. (Woodard-USGS)

Annual summary of ground-water conditions in Arizona, spring 1976 to spring 1977

USGS Publications Warehouse

Babcock, H.M.

1977-01-01

Two small-scale maps of Arizona show (1) pumpage of ground water by areas and (2) the status of the ground-water inventory in the State. The main map, which is at a scale of 1:500,000, shows potential well production, depth of water in selected wells in spring 1977, and change in water level in selected wells from 1972 to 1977. The brief text that accompanies the maps summarizes the current ground-water conditions in the State. The withdrawal of ground water was about 5.5 million acre-feet in Arizona in 1976 of which about 4.7 million acre-feet was used for the irrigation. The Salt River Valley and the lower Santa Cruz basin are the largest agricultural areas in the State. For 1972-76, ground-water withdrawal in the two areas was about 8.2 to 4.9 million acre-feet, respectively, and, in general, water levels are declining. Other areas in which ground-water withdrawals have caused large water-level declines are the Willcox, San Simon, upper Santa Cruz, Avra Valley, Gila Bend, Harquahala Plains, and McMullen Valley areas. (Woodard-USGS)

Mapping Vulnerability to Disasters in Latin America and the Caribbean, 1900-2007

USGS Publications Warehouse

Maynard-Ford, Miriam C.; Phillips, Emily C.; Chirico, Peter G.

2008-01-01

The vulnerability of a population and its infrastructure to disastrous events is a factor of both the probability of a hazardous event occurring and the community's ability to cope with the resulting impacts. Therefore, the ability to accurately identify vulnerable populations and places in order to prepare for future hazards is of critical importance for disaster mitigation programs. This project created maps of higher spatial resolution of vulnerability to disaster in Latin America and the Caribbean from 1900 to 2007 by mapping disaster data by first-level administrative boundaries with the objective of identifying geographic trends in regional occurrences of disasters and vulnerable populations. The method of mapping by administrative level is an improvement on displaying and analyzing disasters at the country level and shows the relative intensity of vulnerability within and between countries in the region. Disaster mapping at the country level produces only a basic view of which countries experience various types of natural disasters. Through disaggregation, the data show which geographic areas of these countries, including populated areas, are historically most susceptible to different hazard types.

Predictive landslide susceptibility mapping using spatial information in the Pechabun area of Thailand

NASA Astrophysics Data System (ADS)

Oh, Hyun-Joo; Lee, Saro; Chotikasathien, Wisut; Kim, Chang Hwan; Kwon, Ju Hyoung

2009-04-01

For predictive landslide susceptibility mapping, this study applied and verified probability model, the frequency ratio and statistical model, logistic regression at Pechabun, Thailand, using a geographic information system (GIS) and remote sensing. Landslide locations were identified in the study area from interpretation of aerial photographs and field surveys, and maps of the topography, geology and land cover were constructed to spatial database. The factors that influence landslide occurrence, such as slope gradient, slope aspect and curvature of topography and distance from drainage were calculated from the topographic database. Lithology and distance from fault were extracted and calculated from the geology database. Land cover was classified from Landsat TM satellite image. The frequency ratio and logistic regression coefficient were overlaid for landslide susceptibility mapping as each factor’s ratings. Then the landslide susceptibility map was verified and compared using the existing landslide location. As the verification results, the frequency ratio model showed 76.39% and logistic regression model showed 70.42% in prediction accuracy. The method can be used to reduce hazards associated with landslides and to plan land cover.

Soil maps as data input for soil erosion models: errors related to map scales

NASA Astrophysics Data System (ADS)

van Dijk, Paul; Sauter, Joëlle; Hofstetter, Elodie

2010-05-01

Soil erosion rates depend in many ways on soil and soil surface characteristics which vary in space and in time. To account for spatial variations of soil features, most distributed soil erosion models require data input derived from soil maps. Ideally, the level of spatial detail contained in the applied soil map should correspond to the objective of the modelling study. However, often the model user has only one soil map available which is then applied without questioning its suitability. The present study seeks to determine in how far soil map scale can be a source of error in erosion model output. The study was conducted on two different spatial scales, with for each of them a convenient soil erosion model: a) the catchment scale using the physically-based Limbourg Soil Erosion Model (LISEM), and b) the regional scale using the decision-tree expert model MESALES. The suitability of the applied soil map was evaluated with respect to an imaginary though realistic study objective for both models: the definition of erosion control measures at strategic locations at the catchment scale; the identification of target areas for the definition of control measures strategies at the regional scale. Two catchments were selected to test the sensitivity of LISEM to the spatial detail contained in soil maps: one catchment with relatively little contrast in soil texture, dominated by loess-derived soil (south of the Alsace), and one catchment with strongly contrasted soils at the limit between the Alsatian piedmont and the loess-covered hills of the Kochersberg. LISEM was run for both catchments using different soil maps ranging in scale from 1/25 000 to 1/100 000 to derive soil related input parameters. The comparison of the output differences was used to quantify the map scale impact on the quality of the model output. The sensitivity of MESALES was tested on the Haut-Rhin county for which two soil maps are available for comparison: 1/50 000 and 1/100 000. The order of resulting target areas (communes) was compared to evaluate the error induced by using the coarser soil data at 1/100 000. Results shows that both models are sensitive to the soil map scale used for model data input. A low sensitivity was found for the catchment with relatively homogeneous soil textures and the use of 1/100 000 soil maps seems allowed. The results for the catchment with strong soil texture variations showed significant differences depending on soil map scale on 75% of the catchment area. Here, the use of 1/100 000 soil map will indeed lead to wrong erosion diagnostics and will hamper the definition of a sound erosion control strategy. The regional scale model MESALES proved to be very sensitive to soil information. The two soil related model parameters (crusting sensitivity, and soil erodibility) reacted very often in the same direction therewith amplifying the change in the final erosion hazard class. The 1/100 000 soil map yielded different results on 40% of the sloping area compared to the 1/50 000 map. Significant differences in the order of target areas were found as well. The present study shows that the degree of sensitivity of the model output to soil map scale is rather variable and depends partly on the spatial variability of soil texture within the study area. Soil (textural) diversity needs to be accounted for to assure a fruitful use of soil erosion models. In some situations this might imply that additional soil data need to be collected in the field to refine the available soil map.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Halliday, M.E.; Cook, K.L.

Regional gravity data were collected in portions of the Pavant Range, Tushar Mountains, northern Sevier Plateau, the Antelope Range, and throughout Sevier Valley approximately between the towns of Richfield and Junction, Utah. Additionally, detailed gravity and ground magnetic data were collected in the vicinity of hot springs in both the Monroe and Joseph Known Geothermal Resource Areas (KGRA's) and subsurface geologic models were constructed. The regional gravity data were terrain corrected out to a distance of 167 km from the station and 948 gravity station values were compiled into a complete Bouguer gravity anomaly map of the survey area. Thismore » map shows a strong correlation with most structural features mapped in the survey area. Four regional gravity profiles were modeled using two-dimensional formerd and inverse algorithms.« less

Application of an adaptive neuro-fuzzy inference system to ground subsidence hazard mapping

NASA Astrophysics Data System (ADS)

Park, Inhye; Choi, Jaewon; Jin Lee, Moung; Lee, Saro

2012-11-01

We constructed hazard maps of ground subsidence around abandoned underground coal mines (AUCMs) in Samcheok City, Korea, using an adaptive neuro-fuzzy inference system (ANFIS) and a geographical information system (GIS). To evaluate the factors related to ground subsidence, a spatial database was constructed from topographic, geologic, mine tunnel, land use, and ground subsidence maps. An attribute database was also constructed from field investigations and reports on existing ground subsidence areas at the study site. Five major factors causing ground subsidence were extracted: (1) depth of drift; (2) distance from drift; (3) slope gradient; (4) geology; and (5) land use. The adaptive ANFIS model with different types of membership functions (MFs) was then applied for ground subsidence hazard mapping in the study area. Two ground subsidence hazard maps were prepared using the different MFs. Finally, the resulting ground subsidence hazard maps were validated using the ground subsidence test data which were not used for training the ANFIS. The validation results showed 95.12% accuracy using the generalized bell-shaped MF model and 94.94% accuracy using the Sigmoidal2 MF model. These accuracy results show that an ANFIS can be an effective tool in ground subsidence hazard mapping. Analysis of ground subsidence with the ANFIS model suggests that quantitative analysis of ground subsidence near AUCMs is possible.

Monitoring Temporal Evolution of the Presence Intermediate Host of the Schistosomiasis and its Risk Transmission Based on Dragon Times Series in Poyang Lake Area Jiangxi Province, P.R. China

NASA Astrophysics Data System (ADS)

Marie, Tiphanie; Lai, Xijun; Huber, Claire; Chen, Xiaoling; Uribe, Carlos; Huang, Shifeng; LaCaux, Jean-Pierre; LaFaye, Murielle; Yesou, Herve

2010-12-01

Earth Observation data were used for mapping potential Schistosomiasis japonica distribution, within Poyang Lake (Jiangxi Province, PR China), as well as transmission risk associated with fishing activities. Areas suitable for the development of Oncomelania hupensis, the intermediate host snail of Schistosoma japonicum, were derived from submersion time parameters and vegetation community indicators. Monthly maps showing the annual dynamic of potential O. hupensis presence areas were obtained from December 2005 to December 2008. Human potential transmission risk was handled through the mapping of settlements and the identification of the principal human activity sensitive to transmission: fishing in the central part of Poyang Lake. Finally, data crossing of the different parameters highlight the potential risk of transmission in most of the fishing nets areas.

Mapping Landslides Susceptibility in a Traditional Northern Nigerian City

NASA Astrophysics Data System (ADS)

Oluwafemi, Olawale A.; Yakubu, Tahir A.; Muhammad, Mahmud U.; Shitta, Nyofo; Akinwumiju, Akinola S.

2018-05-01

As a result of dearth of relevant information about Landslides Susceptibility in Nigeria, the monitoring and assessment appears intractable. Hence, the study developed a Remote Sensing approach to mapping landslides susceptibility, landuse and landcover analysis in Jos South LGA, Plateau State, Nigeria. Field Observation, SPOT 5 2009 and 2012, ASTER DEM 2009, Geological Map 2006, Topographical Map 1966 were used to map Landslide Susceptibility and Landuse /Lancover Analysis in the study area. Geospatial Analytical Operations employed using ArcGIS 10.3 and Erdas Imagine 2014 include Spatial Modeling, Vectorization, Pre-lineament Extraction, Image Processing among others. Result showed that 72.38 % of the study area is underlain by granitic rocks. The landuse/cover types delineated for the study area include floodplain (29.27 %), farmland (23.96 %), sparsely vegetated land (15.43 %), built up area (13.65 %), vegetated outcrop (8.48 %), light vegetation (5.37 %), thick vegetation (2.39 %), water body (0.58 %), plantation (0.50 %) and mining pond (0.37 %). Landslide Susceptibility Analysis also revealed that 87 % of the study area is relatively at low to very low risk of landslide event. While only 13 % of the study area is at high to very high risk of landslide event. The study revealed that the susceptibility of landslide event is very low in the study area. However, possible landslide event in the hot spots could be pronounced and could destabilize the natural and man-made environmental systems of the study area.

LOFAR Lightning Imaging: Mapping Lightning With Nanosecond Precision

NASA Astrophysics Data System (ADS)

Hare, B. M.; Scholten, O.; Bonardi, A.; Buitink, S.; Corstanje, A.; Ebert, U.; Falcke, H.; Hörandel, J. R.; Leijnse, H.; Mitra, P.; Mulrey, K.; Nelles, A.; Rachen, J. P.; Rossetto, L.; Rutjes, C.; Schellart, P.; Thoudam, S.; Trinh, T. N. G.; ter Veen, S.; Winchen, T.

2018-03-01

Lightning mapping technology has proven instrumental in understanding lightning. In this work we present a pipeline that can use lightning observed by the LOw-Frequency ARray (LOFAR) radio telescope to construct a 3-D map of the flash. We show that LOFAR has unparalleled precision, on the order of meters, even for lightning flashes that are over 20 km outside the area enclosed by LOFAR antennas (˜3,200 km2), and can potentially locate over 10,000 sources per lightning flash. We also show that LOFAR is the first lightning mapping system that is sensitive to the spatial structure of the electrical current during individual lightning leader steps.

Mineral resource potential map of the Pyramid Roadless Area, El Dorado County, Colorado

USGS Publications Warehouse

Armstrong, Augustus K.; Chaffee, Maurice A.; Scott, Douglas F.

1983-01-01

Studies show., there is low potential for small deposits of gold, silver, and base metals in the Pyramid Roadless Area. There are two uranium claims (Cliff Ridge mining claims) located within the roadless area, but samples from this site showed no uranium. There are no indications of geothermal resources, coal, oil, or gas.

Geophysical Data (Gravity and Magnetic) from the Area Between Adana, Kahramanmaras and Hatay in the Eastern Mediterranean Region: Tectonic Implications

NASA Astrophysics Data System (ADS)

Over, Semir; Akin, Ugur; Sen, Rahime

2018-01-01

The gravity and magnetic maps of the area between Adana-Kahramanmaras-Hatay provinces were produced from a compilation of data gathered during the period between 1973 and 1989. Reduced to the pole (RTP) and pseudo-gravity transformation (PGT) methods were applied to the magnetic data, while derivative ratio (DR) processing was applied to both gravity and magnetic data, respectively. Bouguer, RTP and PGT maps show the image of a buried structure corresponding to ophiolites under undifferentiated Quaternary deposits in the Adana depression and Iskenderun Gulf. DR maps show two important faults which reflect the tectonic framework in the study area: (1) the Karatas-Osmaniye Fault extending from Osmaniye to Karatas in the south between Adana and Iskenderun depressions and (2) Amanos Fault (southern part of East Anatolian Fault) in the Hatay region running southward from Turkoglu to Amik Basin along Amanos Mountain forming the actual plate boundary between the Anatolian block (part of Eurasian plate) and Arabian plate.

Large area mapping of soil moisture using the ESTAR passive microwave radiometer

NASA Technical Reports Server (NTRS)

Jackson, T. J.; Levine, D. M.; Swift, C. T.; Schmugge, T. J.

1994-01-01

Investigations designed to study land surface hydrologic-atmospheric interactions, showing the potential of L band passive microwave radiometry for measuring surface soil moisture over large areas, are discussed. Satisfying the data needs of these investigations requires the ability to map large areas rapidly. With aircraft systems this means a need for more beam positions over a wider swath on each flightline. For satellite systems the essential problem is resolution. Both of these needs are currently being addressed through the development and verification of Electronically Scanned Thinned Array Radiometer (ESTAR) technology. The ESTAR L band radiometer was evaluated for soil moisture mapping applications in two studies. The first was conducted over the semiarid rangeland Walnut Gulch watershed located in south eastern Arizona (U.S.). The second was performed in the subhumid Little Washita watershed in south west Oklahoma (U.S.). Both tests showed that the ESTAR is capable of providing soil moisture with the same level of accuracy as existing systems.

Potentiometric Surface of the Aquia Aquifer in Southern Maryland, September 2009

USGS Publications Warehouse

Curtin, Stephen E.; Andreasen, David C.; Staley, Andrew W.

2010-01-01

This report presents a map showing the potentiometric surface of the Aquia aquifer in the Aquia Formation of Paleocene age in Southern Maryland during September 2009. The map is based on water-level measurements in 82 wells. The highest measured water level was 48 feet above sea level near the northern boundary and in the outcrop area of the aquifer in the central part of Anne Arundel County. Water levels also were above sea level in Kent County and northern Queen Anne's County. Water levels were below sea level south and east of these areas and in the remainder of the study area. The hydraulic gradient increased southeastward toward a cone of depression around well fields at Lexington Park and Solomons Island. The lowest measured water level was 145 feet below sea level at the center of a cone of depression at Lexington Park. The map also shows well yield in gallons per day for 2008 at wells or well fields.

Spatial-area selective retrieval of multiple object-place associations in a hierarchical cognitive map formed by theta phase coding.

PubMed

Sato, Naoyuki; Yamaguchi, Yoko

2009-06-01

The human cognitive map is known to be hierarchically organized consisting of a set of perceptually clustered landmarks. Patient studies have demonstrated that these cognitive maps are maintained by the hippocampus, while the neural dynamics are still poorly understood. The authors have shown that the neural dynamic "theta phase precession" observed in the rodent hippocampus may be capable of forming hierarchical cognitive maps in humans. In the model, a visual input sequence consisting of object and scene features in the central and peripheral visual fields, respectively, results in the formation of a hierarchical cognitive map for object-place associations. Surprisingly, it is possible for such a complex memory structure to be formed in a few seconds. In this paper, we evaluate the memory retrieval of object-place associations in the hierarchical network formed by theta phase precession. The results show that multiple object-place associations can be retrieved with the initial cue of a scene input. Importantly, according to the wide-to-narrow unidirectional connections among scene units, the spatial area for object-place retrieval can be controlled by the spatial area of the initial cue input. These results indicate that the hierarchical cognitive maps have computational advantages on a spatial-area selective retrieval of multiple object-place associations. Theta phase precession dynamics is suggested as a fundamental neural mechanism of the human cognitive map.

Near real-time skin deformation mapping

NASA Astrophysics Data System (ADS)

Kacenjar, Steve; Chen, Suzie; Jafri, Madiha; Wall, Brian; Pedersen, Richard; Bezozo, Richard

2013-02-01

A novel in vivo approach is described that provides large area mapping of the mechanical properties of the skin in human patients. Such information is important in the understanding of skin health, cosmetic surgery[1], aging, and impacts of sun exposure. Currently, several methods have been developed to estimate the local biomechanical properties of the skin, including the use of a physical biopsy of local areas of the skin (in vitro methods) [2, 3, and 4], and also the use of non-invasive methods (in vivo) [5, 6, and 7]. All such methods examine localized areas of the skin. Our approach examines the local elastic properties via the generation of field displacement maps of the skin created using time-sequence imaging [9] with 2D digital imaging correlation (DIC) [10]. In this approach, large areas of the skin are reviewed rapidly, and skin displacement maps are generated showing the contour maps of skin deformation. These maps are then used to precisely register skin images for purposes of diagnostic comparison. This paper reports on our mapping and registration approach, and demonstrates its ability to accurately measure the skin deformation through a described nulling interpolation process. The result of local translational DIC alignment is compared using this interpolation process. The effectiveness of the approach is reported in terms of residual RMS, image entropy measures, and differential segmented regional errors.

Evaluation of ERTS-1 imagery for mapping Quaternary deposits and landforms in the Great Plains and Midwest

NASA Technical Reports Server (NTRS)

Morrison, R. B. (Principal Investigator); Hallberg, G. R.

1973-01-01

The author has identified the following significant results. The main landform associations and larger landforms are readily identifiable on the better images and commonly the gross associations of surficial Quaternary deposits also can be differentiated, primarily by information on landforms and soils. Maps showing the Quaternary geologic-terrain units that can be differentiated from the ERTS-1 images are being prepared for study areas in Illinois, Iowa, Missouri, Kansas, Nebraska, and South Dakota. Preliminary maps at 1:1 million scale are given of two of the study areas, the Peoria and Decatur, Illinois, 1 deg x 2 quadrangles. These maps exemplify the first phase of investigations, which consists of identifying and mapping landform and land use characteristics and geologic-surficial materials directly from ERTS-1 images alone, without input of additional data. These maps shown that commonly the boundaries of geologic-terrain units can be identified more accurately on ERTS-1 images than on topographic maps of 1:250,000 scale. From analysis of drainage patterns, stream-divide relations, and tone and textural variations on the ERTS-1 images, the trends of numerous moraines of Wisconsinan and possibly some of Illinoian age were mapped. In the Peoria study area the trend of a buried valley of the Mississippi River is revealed.

Bathymetric survey of Carroll Creek Tributary to Lake Tuscaloosa, Tuscaloosa County, Alabama, 2010

USGS Publications Warehouse

Lee, K.G.; Kimbrow, D.R.

2011-01-01

The U.S. Geological Survey, in cooperation with the City of Tuscaloosa, conducted a bathymetric survey of Carroll Creek, on May 12-13, 2010. Carroll Creek is one of the major tributaries to Lake Tuscaloosa and contributes about 6 percent of the surface drainage area. A 3.5-mile reach of Carroll Creek was surveyed to prepare a current bathymetric map, determine storage capacities at specified water-surface elevations, and compare current conditions to historical cross sections. Bathymetric data were collected using a high-resolution interferometric mapping system consisting of a phase-differencing bathymetric sonar, navigation and motion-sensing system, and a data acquisition computer. To assess the accuracy of the interferometric mapping system and document depths in shallow areas of the study reach, an electronic total station was used to survey 22 cross sections spaced 50 feet apart. The data were combined and processed and a Triangulated Irregular Network (TIN) and contour map were generated. Cross sections were extracted from the TIN and compared with historical cross sections. Between 2004 and 2010, the area (cross section 1) at the confluence of Carroll Creek and the main run of LakeTuscaloosa showed little to no change in capacity area. Another area (cross section 2) showed a maximum change in elevation of 4 feet and an average change of 3 feet. At the water-surface elevation of 224 feet (National Geodetic Vertical Datum of 1929), the cross-sectional area has changed by 260 square feet for a total loss of 28 percent of cross-sectional storage area. The loss of area may be attributed to sedimentation in Carroll Creek and (or) the difference in accuracy between the two surveys.

Identification of areas of recharge and discharge using Landsat-TM satellite imagery and aerial photography mapping techniques

NASA Astrophysics Data System (ADS)

Salama, R. B.; Tapley, I.; Ishii, T.; Hawkes, G.

1994-10-01

Aerial photographs (AP) and Landsat (TM) colour composites were used to map the geomorphology, geology and structures of the Salt River System of Western Australia. Geomorphic features identified are sand plains, dissected etchplain, colluvium, lateritic duricrust and rock outcrops. The hydrogeomorphic units include streams, lakes and playas, palaeochannels and palaeodeltas. The structural features are linear and curvilinear lineaments, ring structures and dolerite dykes. Suture lines control the course of the main river channel. Permeable areas around the circular granitic plutons were found to be the main areas of recharge in the uplands. Recharge was also found to occur in the highly permeable areas of the sandplains. Discharge was shown to be primarily along the main drainage lines, on the edge of the circular sandplains, in depressions and in lakes. The groundwater occurrence and hydrogeological classification of the recharge potential of the different units were used to classify the mapped areas into recharge and discharge zones. The results also show that TM colour composites provide a viable source of data comparable with AP for mapping and delineating areas of recharge and discharge on a regional scale.

Testing of stack-unit/aquifer sensitivity analysis using contaminant plume distribution in the subsurface of Savannah River Site, South Carolina, USA

USGS Publications Warehouse

Rine, J.M.; Shafer, J.M.; Covington, E.; Berg, R.C.

2006-01-01

Published information on the correlation and field-testing of the technique of stack-unit/aquifer sensitivity mapping with documented subsurface contaminant plumes is rare. The inherent characteristic of stack-unit mapping, which makes it a superior technique to other analyses that amalgamate data, is the ability to deconstruct the sensitivity analysis on a unit-by-unit basis. An aquifer sensitivity map, delineating the relative sensitivity of the Crouch Branch aquifer of the Administrative/Manufacturing Area (A/M) at the Savannah River Site (SRS) in South Carolina, USA, incorporates six hydrostratigraphic units, surface soil units, and relevant hydrologic data. When this sensitivity map is compared with the distribution of the contaminant tetrachloroethylene (PCE), PCE is present within the Crouch Branch aquifer within an area classified as highly sensitive, even though the PCE was primarily released on the ground surface within areas classified with low aquifer sensitivity. This phenomenon is explained through analysis of the aquifer sensitivity map, the groundwater potentiometric surface maps, and the plume distributions within the area on a unit-by- unit basis. The results of this correlation show how the paths of the PCE plume are influenced by both the geology and the groundwater flow. ?? Springer-Verlag 2006.

Assessment of Three Flood Hazard Mapping Methods: A Case Study of Perlis

NASA Astrophysics Data System (ADS)

Azizat, Nazirah; Omar, Wan Mohd Sabki Wan

2018-03-01

Flood is a common natural disaster and also affect the all state in Malaysia. Regarding to Drainage and Irrigation Department (DID) in 2007, about 29, 270 km2 or 9 percent of region of the country is prone to flooding. Flood can be such devastating catastrophic which can effected to people, economy and environment. Flood hazard mapping can be used is an important part in flood assessment to define those high risk area prone to flooding. The purposes of this study are to prepare a flood hazard mapping in Perlis and to evaluate flood hazard using frequency ratio, statistical index and Poisson method. The six factors affecting the occurrence of flood including elevation, distance from the drainage network, rainfall, soil texture, geology and erosion were created using ArcGIS 10.1 software. Flood location map in this study has been generated based on flooded area in year 2010 from DID. These parameters and flood location map were analysed to prepare flood hazard mapping in representing the probability of flood area. The results of the analysis were verified using flood location data in year 2013, 2014, 2015. The comparison result showed statistical index method is better in prediction of flood area rather than frequency ratio and Poisson method.

New geologic mapping of the northwestern Willamette Valley, Oregon, and its American Viticultural Areas (AVAs)—A foundation for understanding their terroir

USGS Publications Warehouse

Wells, Ray E.; Haugerud, Ralph A.; Niem, Alan; Niem, Wendy; Ma, Lina; Madin, Ian; Evarts, Russell C.

2018-04-10

A geologic map of the greater Portland, Oregon, metropolitan area is planned that will document the region’s complex geology (currently in review: “Geologic map of the greater Portland metropolitan area and surrounding region, Oregon and Washington,” by Wells, R.E., Haugerud, R.A., Niem, A., Niem, W., Ma, L., Evarts, R., Madin, I., and others). The map, which is planned to be published as a U.S. Geological Survey Scientific Investigations Map, will consist of 51 7.5′ quadrangles covering more than 2,500 square miles, and it will represent more than 100 person-years of geologic mapping and studies. The region was mapped at the relatively detailed scale of 1:24,000 to improve understanding of its geology and its earthquake hazards. More than 100 geologic map units will record the 50-million-year history of volcanism, sedimentation, folding, and faulting above the Cascadia Subduction Zone. The geology contributes to the varied terroir of four American Viticultural Areas (AVAs) in the northwestern Willamette Valley: the Yamhill-Carlton, Dundee Hills, Chehalem Mountains, and Ribbon Ridge AVAs. Terroir is defined as the environmental conditions, especially climate and soils, that influence the quality and character of a region’s crops—in this case, grapes for wine.On this new poster (“New geologic mapping of the northwestern Willamette Valley, Oregon, and its American Viticultural Areas (AVAs)—A foundation for understanding their terroir”), we present the geologic map at a reduced scale (about 1:175,000) to show the general distribution of geologic map units, and we highlight, discuss, and illustrate six major geologic events that helped shape the region and form its terrior. We also discuss the geologic elements that contribute to the character of each of the four AVAs in the northwestern Willamette Valley.

An Example of Unsupervised Networks Kohonen's Self-Organizing Feature Map

NASA Technical Reports Server (NTRS)

Niebur, Dagmar

1995-01-01

Kohonen's self-organizing feature map belongs to a class of unsupervised artificial neural network commonly referred to as topographic maps. It serves two purposes, the quantization and dimensionality reduction of date. A short description of its history and its biological context is given. We show that the inherent classification properties of the feature map make it a suitable candidate for solving the classification task in power system areas like load forecasting, fault diagnosis and security assessment.

Automated Glacier Mapping using Object Based Image Analysis. Case Studies from Nepal, the European Alps and Norway

NASA Astrophysics Data System (ADS)

Vatle, S. S.

2015-12-01

Frequent and up-to-date glacier outlines are needed for many applications of glaciology, not only glacier area change analysis, but also for masks in volume or velocity analysis, for the estimation of water resources and as model input data. Remote sensing offers a good option for creating glacier outlines over large areas, but manual correction is frequently necessary, especially in areas containing supraglacial debris. We show three different workflows for mapping clean ice and debris-covered ice within Object Based Image Analysis (OBIA). By working at the object level as opposed to the pixel level, OBIA facilitates using contextual, spatial and hierarchical information when assigning classes, and additionally permits the handling of multiple data sources. Our first example shows mapping debris-covered ice in the Manaslu Himalaya, Nepal. SAR Coherence data is used in combination with optical and topographic data to classify debris-covered ice, obtaining an accuracy of 91%. Our second example shows using a high-resolution LiDAR derived DEM over the Hohe Tauern National Park in Austria. Breaks in surface morphology are used in creating image objects; debris-covered ice is then classified using a combination of spectral, thermal and topographic properties. Lastly, we show a completely automated workflow for mapping glacier ice in Norway. The NDSI and NIR/SWIR band ratio are used to map clean ice over the entire country but the thresholds are calculated automatically based on a histogram of each image subset. This means that in theory any Landsat scene can be inputted and the clean ice can be automatically extracted. Debris-covered ice can be included semi-automatically using contextual and morphological information.

Native protein mapping and visualization of protein interactions in the area of human plasma high-density lipoprotein by combining nondenaturing micro 2DE and quantitative LC-MS/MS.

PubMed

Jin, Ya; Bu, Shujie; Zhang, Jun; Yuan, Qi; Manabe, Takashi; Tan, Wen

2014-07-01

A human plasma sample was subjected to nondenaturing micro 2DE and a gel area (5 mm × 18 mm) that includes high-density lipoprotein (HDL) was cut into 1 mm × 1 mm squares, then the proteins in the 90 gel pieces were analyzed by quantitative LC-MS/MS. Grid-cutting of the gel was employed to; (i) ensure the total analysis of the proteins in the area, (ii) standardize the conditions of analysis by LC-MS/MS, (iii) reconstruct the protein distribution patterns from the quantity data. Totally 154 proteins were assigned in the 90 gel pieces and the quantity distribution of each was reconstructed as a color density pattern (a native protein map). The map of apolipoprotein (Apo) A-I showed a wide apparent mass distribution characteristic to HDL and was compared with the maps of the other 153 proteins. Eleven proteins showed maps of wide distribution that overlapped with the map of Apo A-I, and all have been reported to be the components of HDL. Further, seven minor proteins associated with HDL were detected at the gel positions of high Apo A-I quantity. These results for the first time visualized the localization of HDL apolipoproteins on a nondenaturing 2DE gel and strongly suggested their interactions. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Bedrock geologic map of the Seward Peninsula, Alaska, and accompanying conodont data

USGS Publications Warehouse

Till, Alison B.; Dumoulin, Julie A.; Werdon, Melanie B.; Bleick, Heather A.

2011-01-01

This 1:500,000-scale geologic map depicts the bedrock geology of Seward Peninsula, western Alaska, on the North American side of the Bering Strait. The map encompasses all of the Teller, Nome, Solomon, and Bendeleben 1:250,000-scale quadrangles, and parts of the Shishmaref, Kotzebue, Candle, and Norton Bay 1:250,000-scale quadrangles (sh. 1; sh. 2). The geologic map is presented on Sheet 1. The pamphlet includes an introductory text, detailed unit descriptions, tables of geochronologic data, and an appendix containing conodont (microfossil) data and a text explaining those data. Sheet 2 shows metamorphic and tectonic units, conodont color alteration indices, key metamorphic minerals, and locations of geochronology samples listed in the pamphlet. The map area covers 74,000 km2, an area slightly larger than West Virginia or Ireland.

A global tectonic activity map with orbital photographic supplement

NASA Technical Reports Server (NTRS)

Lowman, P. D., Jr.

1981-01-01

A three part map showing equatorial and polar regions was compiled showing tectonic and volcanic activity of the past one million years, including the present. Features shown include actively spreading ridges, spreading rates, major active faults, subduction zones, well defined plates, and volcanic areas active within the past one million years. Activity within this period was inferred from seismicity (instrumental and historic), physiography, and published literature. The tectonic activity map was used for planning global geodetic programs of satellite laser ranging and very long base line interferometry and for geologic education.

Investigations using data from LANDSAT-2. [earth resources program maps forecasting

NASA Technical Reports Server (NTRS)

Hossain, A. (Principal Investigator)

1976-01-01

The author has identified the following significant results. LANDSAT imageries have given positive indication of new land formation in the Bay of Bengal. A map of the bay region showing depth of new formations south of Patherghata test site was prepared. Winter crop estimation of the Sylhet-Mymensingh districts was made. This estimate shows an agreement of about 93% with 1973 data of the Agriculture Department. A preliminary land use map of the Sylhet-Mymensingh area using LANDSAT imageries in conjunction with aerial photographs and ground survey was also prepared.

Diagnostic lumbosacral segmental nerve blocks with local anesthetics: a prospective double-blind study on the variability and interpretation of segmental effects.

PubMed

Wolff, A P; Groen, G J; Crul, B J

2001-01-01

Selective spinal nerve infiltration blocks are used diagnostically in patients with chronic low back pain radiating into the leg. Generally, a segmental nerve block is considered successful if the pain is reduced substantially. Hypesthesia and elicited paresthesias coinciding with the presumed segmental level are used as controls. The interpretation depends on a standard dermatomal map. However, it is not clear if this interpretation is reliable enough, because standard dermatomal maps do not show the overlap of neighboring dermatomes. The goal of the present study is to establish if dissimilarities exist between areas of hypesthesia, spontaneous pain reported by the patient, pain reduction by local anesthetics, and paresthesias elicited by sensory electrostimulation. A secondary goal is to determine to what extent the interpretation is improved when the overlaps of neighboring dermatomes are taken into account. Patients suffering from chronic low back pain with pain radiating into the leg underwent lumbosacral segmental nerve root blocks at subsequent levels on separate days. Lidocaine (2%, 0.5 mL) mixed with radiopaque fluid (0.25 mL) was injected after verifying the target location using sensory and motor electrostimulation. Sensory changes (pinprick method), paresthesias (reported by the patient), and pain reduction (Numeric Rating Scale) were reported. Hypesthesia and paresthesias were registered in a standard dermatomal map and in an adapted map which included overlap of neighboring dermatomes. The relationships between spinal level of injection, extent of hypesthesia, location of paresthesias, and corresponding dermatome were assessed quantitatively. Comparison of the results between both dermatomal maps was done by paired t-tests. After inclusion, data were processed for 40 segmental nerve blocks (L2-S1) performed in 29 patients. Pain reduction was achieved in 43%. Hypesthetic areas showed a large variability in size and location, and also in comparison to paresthesias. Mean hypesthetic area amounted 2.7 +/- 1.4 (+/- SD: range, 0 to 6; standard map) and 3.6 +/- 1.8 (0 to 6; adapted map; P <.001) dermatomes. In these cases, hypesthesia in the corresponding dermatome was found in 80% (standard map) and 88% of the cases (adapted map, not significant). Paresthesias occurring in the corresponding dermatome were found in 80% (standard map) compared with 98% (adapted map, P <.001). In 85% (standard map) and 88% (adapted map), spontaneous pain was present in the dermatome corresponding to the level of local anesthetic injection. In 55% (standard map) versus 75% (adapted map, P <.005), a combination of spontaneous pain, hypesthesia, and paresthesias was found in the corresponding dermatome. Hypesthetic areas determined after lumbosacral segmental nerve blocks show a large variability in size and location compared with elicited paresthesias. Confirmation of an adequately performed segmental nerve block, determined by coexistence of hypesthesia, elicited paresthesias and pain in the presumed dermatome, is more reliable when the overlap of neighboring dermatomes is taken into account.

Map showing how the potentiometric surface of the Magothy Aquifer of August 1980 differed from the potentiometric surface of September 1977, in southern Maryland

USGS Publications Warehouse

Mack, Frederick K.; Wheeler, J.C.; Curtin, Stephen E.

1982-01-01

The map is based on the differences between two sets of water-level measurements made in 65 observation wells. One set was made in 1977, a relatively dry year, and the other set was made in 1980, another relatively dry year. The map shows that the potentiometric surface was higher in 1980, by as much as 9 feet, than it was in 1977, in a band a few miles wide near the outcrop and subcrop areas of the aquifer in northern Prince Georges County and central Anne Arundel County. In the remainder of the map area, the 1980 potentiometric surface was lower than it had been in 1977, with declines as great as 20 feet measured in well fields at Waldorf and Chalk Point. The network of observation wells was developed and is operated and maintained as part of the cooperative program between the U.S. Geological Survey and agencies of the Maryland Department of Natural Resources. (USGS)

Map showing general chemical quality of surface water in the Richfield Quadrangle, Utah

USGS Publications Warehouse

Price, Don

1980-01-01

This is one of a series of maps that describe the geology and related natural resources of the Richfield 2° quadrangle, Utah. The purpose of this map is to show the general chemical quality of surface water in the area by ranges of dissolved-solids concentrations.Data used to compile this map were collected by the U.S. Geological Survey in cooperation with the Utah Department of Natural Resources, Division of Water Rights. In those areas where little or no surface-water-quality data are available, ranges of dissolved-solids concentrations of the water are inferred on the basis of such factors as geology (Stokes, 1964), precipitation, topography, known ground-water quality, and water uses – all of which affect the chemical quality of surface water.Additional information about the chemical quality of surface water in various parts of the Richfield 2° quadrangle may be found in the following reports: Hahl and Cabell (1965), Hahl and Mundorff (1968), Stephens (1974, 1976), Cruff and Mower (1976), and Cruff(1977)

Mapping Malaria Transmission Risk in Northern Morocco Using Entomological and Environmental Data

PubMed Central

Adlaoui, E.; Faraj, C.; El Bouhmi, M.; El Aboudi, A.; Ouahabi, S.; Tran, A.; Fontenille, D.; El Aouad, R.

2011-01-01

Malaria resurgence risk in Morocco depends, among other factors, on environmental changes as well as the introduction of parasite carriers. The aim of this paper is to analyze the receptivity of the Loukkos area, large wetlands in Northern Morocco, to quantify and to map malaria transmission risk in this region using biological and environmental data. This risk was assessed on entomological risk basis and was mapped using environmental markers derived from satellite imagery. Maps showing spatial and temporal variations of entomological risk for Plasmodium vivax and P. falciparum were produced. Results showed this risk to be highly seasonal and much higher in rice fields than in swamps. This risk is lower for Afrotropical P. falciparum strains because of the low infectivity of Anopheles labranchiae, principal malaria vector in Morocco. However, it is very high for P. vivax mainly during summer corresponding to the rice cultivation period. Although the entomological risk is high in Loukkos region, malaria resurgence risk remains very low, because of the low vulnerability of the area. PMID:22312566

Maps and tables showing data and analyses of semiquantitative emmission spectrometry and atomic-absorption spectrophotometry of rock samples, Ugashik, Bristol Bay, and part of Karluk quadrangles, Alaska

USGS Publications Warehouse

Wilson, Frederic H.; O'Leary, R. M.

1986-01-01

The accompanying maps and tables show analytical data and data analyses from rock samples collected in conjunction with geologic mapping in the Ugashik, Bristol Bay and western Karluck quadrangles from 1979 through 1981. This work was conducted under the auspices of the Alaska Mineral Resource Assessment Program (AMRAP). A total of 337 samples were collected for analysis, primarily in areas of surficial alteration. The sample locations are shown on sheet 1: they are concentrated along the Pacific Ocean side of the area because the Bristol Bay lowlands part of the map is predominantly unconsolidated Quaternary deposits. Sample collection was by the following people, with their respective two letter identifying code shown in parentheses: W.H. Allaway (AY), J.E. Case (CE), D.P. Cox (CX), R.L. Detterman, (DT), T.G. Theodore (MK), F.H. Wilson (WS), and M.E. Yount (YB).

Geologic Map of The Volcanoes Quadrangle, Bernalillo and Sandoval Counties, New Mexico

USGS Publications Warehouse

Thompson, Ren A.; Shroba, Ralph R.; Menges, Christopher M.; Schmidt, Dwight L.; Personius, Stephen F.; Brandt, Theodore R.

2009-01-01

This geologic map, in support of the U.S. Geological Survey Middle Rio Grande Basin Geologic Mapping Project, shows the spatial distribution of surficial deposits, lava flows, and related sediments of the Albuquerque volcanoes, upper Santa Fe Group sediments, faults, and fault-related structural features. These deposits are on, along, and beneath the Llano de Albuquerque (West Mesa) west of Albuquerque, New Mexico. Some of these deposits are in the western part of Petroglyph National Monument. Artificial fill deposits are mapped chiefly beneath and near the City of Albuquerque Soil Amendment Facility and the Double Eagle II Airport. Alluvial deposits were mapped in and along stream channels, beneath terrace surfaces, and on the Llano de Albuquerque and its adjacent hill slopes. Deposits composed of alluvium and colluvium are also mapped on hill slopes. Wedge-shaped deposits composed chiefly of sandy sheetwash deposits, eolian sand, and intercalated calcic soils have formed on the downthrown-sides of faults. Deposits of active and inactive eolian sand and sandy sheetwash deposits mantle the Llano de Albuquerque. Lava flows and related sediments of the Albuquerque volcanoes were mapped near the southeast corner of the map area. They include eleven young lava flow units and, where discernable, associated vent and near-vent pyroclastic deposits associated with cinder cones. Upper Santa Fe Group sediments are chiefly fluvial in origin, and are well exposed near the western boundary of the map area. From youngest to oldest they include a gravel unit, pebbly sand unit, tan sand and mud unit, tan sand unit, tan sand and clay unit, and silty sand unit. Undivided upper Santa Fe Group sediments are mapped in the eastern part of the map area. Faults were identified on the basis of surface expression determined from field mapping and interpretation of aeromagnetic data where concealed beneath surficial deposits. Fault-related structural features are exposed and were mapped near the western boundary of the map area.

Bedmap2; Mapping, visualizing and communicating the Antarctic sub-glacial environment.

NASA Astrophysics Data System (ADS)

Fretwell, Peter; Pritchard, Hamish

2013-04-01

Bedmap2; Mapping, visualizing and communicating the Antarctic sub-glacial environment. The Bedmap2 project has been a large cooperative effort to compile, model, map and visualize the ice-rock interface beneath the Antarctic ice sheet. Here we present the final output of that project; the Bedmap2 printed map. The map is an A1, double sided print, showing 2d and 3d visualizations of the dataset. It includes scientific interpretations, cross sections and comparisons with other areas. Paper copies of the colour double sided map will be freely distributed at this session.

A spatial database of bedding attitudes to accompany Geologic Map of Boulder-Fort Collins-Greeley Area, Colorado

USGS Publications Warehouse

Colton, Roger B.; Brandt, Theodore R.; Moore, David W.; Murray, Kyle E.

2003-01-01

This digital map shows bedding attitude data displayed over the geographic extent of rock stratigraphic units (formations) as compiled by Colton in 1976 (U.S.Geological Survey Map I-855-G) under the Front Range Urban Corridor Geology Program. Colton used his own mapping and published geologic maps having varied map unit schemes to compile one map with a uniform classification of geologic units. The resulting published color paper map was intended for planning for use of land in the Front Range Urban Corridor. In 1997-1999, under the USGS Front Range Infrastructure Resources Project, Colton's map was digitized to provide data at 1:100,000 scale to address urban growth issues(see cross-reference). In general, the west part of the map shows a variety of Precambrian igneous and metamorphic rocks, major faults and brecciated zones along an eastern strip (5-20 km wide) of the Front Range. The eastern and central part of the map (Colorado Piedmont) depicts a mantle of Quaternary unconsolidated deposits and interspersed Cretaceous or Tertiary-Cretaceous sedimentary rock outcrops. The Quaternary mantle is comprised of eolian deposits (quartz sand and silt), alluvium (gravel, sand, and silt of variable composition), colluvium, and few landslides. At the mountain front, north-trending, dipping Paleozoic and Mesozoic sandstone and shale formations (and sparse limestone) form hogbacks, intervening valleys, and in range-front folds, anticlines, and fault blocks. Localized dikes and sills of Tertiary rhyodacite and basalt intrude rocks near the range front, mostly in the Boulder area.

Assessment and mapping of water pollution indices in zone-III of municipal corporation of hyderabad using remote sensing and geographic information system.

PubMed

Asadi, S S; Vuppala, Padmaja; Reddy, M Anji

2005-01-01

A preliminary survey of area under Zone-III of MCH was undertaken to assess the ground water quality, demonstrate its spatial distribution and correlate with the land use patterns using advance techniques of remote sensing and geographical information system (GIS). Twenty-seven ground water samples were collected and their chemical analysis was done to form the attribute database. Water quality index was calculated from the measured parameters, based on which the study area was classified into five groups with respect to suitability of water for drinking purpose. Thematic maps viz., base map, road network, drainage and land use/land cover were prepared from IRS ID PAN + LISS III merged satellite imagery forming the spatial database. Attribute database was integrated with spatial sampling locations map in Arc/Info and maps showing spatial distribution of water quality parameters were prepared in Arc View. Results indicated that high concentrations of total dissolved solids (TDS), nitrates, fluorides and total hardness were observed in few industrial and densely populated areas indicating deteriorated water quality while the other areas exhibited moderate to good water quality.

Preliminary lithogeochemical map showing near-surface rock types in the Chesapeake Bay watershed, Virginia and Maryland

USGS Publications Warehouse

Peper, John D.; McCartan, Lucy; Horton, J. Wright; Reddy, James E.

2001-01-01

This preliminary experimental lithogeochemical map shows the distribution of rock types in the Virginia and Maryland parts of the Chesapeake Bay watershed. The map was produced digitally by classifying geologic-map units according to composition, mineralogy, and texture; rather than by age and stratigraphic relationships as shown on traditional geologic maps. This map differs from most lithologic maps in that the lithogeochemical unit classification distinguishes those rock units having key water-reactive minerals that may induce acid neutralization, or reduction, of hosted water at the weathering interface. The validity of these rock units, however, is independent of water chemistry, because the rock units are derived from geologic maps and rock descriptions. Areas of high soil carbon content, and sulfide metal deposits are also shown. Water-reactive minerals and their weathering reactions yield five lithogeochemical unit classes: 1) carbonate rock and calcareous rocks and sediments, the most acid-neutralizing; 2)carbonaceous-sulfidic rocks and sediments, oxygen-depleting and reducing; 3) quartzofeldspathic rocks and siliciclastic sediments, relatively weakly reactive with water; 4) mafic silicate rocks/sediments, oxygen consuming and high solute-load delivering; and, 5) the rarer calcareous-sulfidic (carbonaceous) rocks, neutralizing and reducing. Earlier studies in some parts of the map area have related solute loads in ground and stream waters to some aspects of bedrock lithology. More recent preliminary tests of relationships between four of the classes of mapped lithogeochemical units and ground water chemistry, in the Mid-Atlantic area using this map, have focused on and verified the nitrate-reducing and acid-neutralizing properties of some bedrock and unconsolidated aquifer rock types. Sulfide mineral deposits and their mine-tailings effects on waters are beginning to be studied by others. Additional testing of relationships among the lithogeochemical units and aspects of ground and surface water chemistry could help to refine the lithogeochemical classification, and this map. The testing could also improve the usefulness of the map for assessing aquifer reactivity and the transport properties of reactive contaminants such as acid rain, and nitrate from agricultural sources, in the Chesapeake Bay watershed.

Mapping Urban Environmental Noise Using Smartphones.

PubMed

Zuo, Jinbo; Xia, Hao; Liu, Shuo; Qiao, Yanyou

2016-10-13

Noise mapping is an effective method of visualizing and accessing noise pollution. In this paper, a noise-mapping method based on smartphones to effectively and easily measure environmental noise is proposed. By using this method, a noise map of an entire area can be created using limited measurement data. To achieve the measurement with certain precision, a set of methods was designed to calibrate the smartphones. Measuring noise with mobile phones is different from the traditional static observations. The users may be moving at any time. Therefore, a method of attaching an additional microphone with a windscreen is proposed to reduce the wind effect. However, covering an entire area is impossible. Therefore, an interpolation method is needed to achieve full coverage of the area. To reduce the influence of spatial heterogeneity and improve the precision of noise mapping, a region-based noise-mapping method is proposed in this paper, which is based on the distribution of noise in different region types tagged by volunteers, to interpolate and combine them to create a noise map. To validate the effect of the method, a comparison of the interpolation results was made to analyse our method and the ordinary Kriging method. The result shows that our method is more accurate in reflecting the local distribution of noise and has better interpolation precision. We believe that the proposed noise-mapping method is a feasible and low-cost noise-mapping solution.

Mapping Urban Environmental Noise Using Smartphones

PubMed Central

Zuo, Jinbo; Xia, Hao; Liu, Shuo; Qiao, Yanyou

2016-01-01

Noise mapping is an effective method of visualizing and accessing noise pollution. In this paper, a noise-mapping method based on smartphones to effectively and easily measure environmental noise is proposed. By using this method, a noise map of an entire area can be created using limited measurement data. To achieve the measurement with certain precision, a set of methods was designed to calibrate the smartphones. Measuring noise with mobile phones is different from the traditional static observations. The users may be moving at any time. Therefore, a method of attaching an additional microphone with a windscreen is proposed to reduce the wind effect. However, covering an entire area is impossible. Therefore, an interpolation method is needed to achieve full coverage of the area. To reduce the influence of spatial heterogeneity and improve the precision of noise mapping, a region-based noise-mapping method is proposed in this paper, which is based on the distribution of noise in different region types tagged by volunteers, to interpolate and combine them to create a noise map. To validate the effect of the method, a comparison of the interpolation results was made to analyse our method and the ordinary Kriging method. The result shows that our method is more accurate in reflecting the local distribution of noise and has better interpolation precision. We believe that the proposed noise-mapping method is a feasible and low-cost noise-mapping solution. PMID:27754359

Annual Dynamics of Forest Areas in South America during 2007-2010 at 50-m Spatial Resolution

NASA Astrophysics Data System (ADS)

Qin, Y.; Xiao, X.; Dong, J.; Zhou, Y.; Wang, J.; Doughty, R.; Chen, Y.; Zou, Z.; Moore, B., III

2017-12-01

The user community has an urgent need for high accuracy tropical forest distribution and spatio-temporal changes since tropical forests are facing defragmentation and persistent clouds. In this study, we selected South America as a hotspot and presented a robust approach to map annual forests during 2007-2010 based on the coupled greenness-relevant MOD13Q1 NDVI and structure/biomass-relevant ALOS PALSAR time series data. We analyzed the consistency and uncertainty among eight major forest maps at continental, country, and pixel scales. The 50-m PALSAR/MODIS forest area in South America was about 8.63×106 km2 in 2010. Large differences in total forest area (8.2×106 km2-12.7×106 km2) existed among these forest products. Forest products generated under a similar forest definition had similar or even larger variation than those generated under differing forest definitions. One needs to consider leaf area index as an adjusting factor and use much higher threshold values in the VCF datasets to estimate forest cover. Analyses of PALSAR/MODIS forest maps showed a relatively small and equivalent rate of loss (3.2×104 km2 year-1) in net forest cover to that of FAO FRA (3.3×104 km2 year-1). PALSAR/MODIS forest maps showed that more and more deforestation occurred in the intact forest areas. The rate of forest loss (1.95×105 km2 year-1) was higher than that of Global Forest Watch (0.81×105 km2 year-1). Caution should be used when using the different forest maps to analyze forest loss and make policies regarding forest ecosystem services and biodiversity conservation.

Soil Carbon Mapping in Low Relief Areas with Combined Land Use Types and Percentages

NASA Astrophysics Data System (ADS)

Liu, Y. L.; Wu, Z. H.; Chen, Y. Y.; Wang, B. Z.

2018-05-01

Accurate mapping of soil carbon in low relief areas is of great challenge because of the defect of conventional "soil-landscape" model. Efforts have been made to integrate the land use information in the modelling and mapping of soil organic carbon (SOC), in which the spatial context was ignored. With 256 topsoil samples collected from Jianghan Plain, we aim to (i) explore the land-use dependency of SOC via one-way ANOVA; (ii) investigate the "spillover effect" of land use on SOC content; (iii) examine the feasibility of land use types and percentages (obtained with a 200-meter buffer) for soil mapping via regression Kriging (RK) models. Results showed that the SOC of paddy fields was higher than that of woodlands and irrigated lands. The land use type could explain 20.5 % variation of the SOC, and the value increased to 24.7 % when the land use percentages were considered. SOC was positively correlated with the percentage of water area and irrigation canals. Further research indicated that SOC of irrigated lands was significantly correlated with the percentage of water area and irrigation canals, while paddy fields and woodlands did not show similar trends. RK model that combined land use types and percentages outperformed the other models with the lowest values of RMSEC (5.644 g/kg) and RMSEP (6.229 g/kg), and the highest R2C (0.193) and R2P (0.197). In conclusions, land use types and percentages serve as efficient indicators for the SOC mapping in plain areas. Additionally, irrigation facilities contributed to the farmland SOC sequestration especially in irrigated lands.

Next-Level ShakeZoning for Earthquake Hazard Definition in Nevada

NASA Astrophysics Data System (ADS)

Louie, J. N.; Savran, W. H.; Flinchum, B. A.; Dudley, C.; Prina, N.; Pullammanappallil, S.; Pancha, A.

2011-12-01

We are developing "Next-Level ShakeZoning" procedures tailored for defining earthquake hazards in Nevada. The current Federally sponsored tools- the USGS hazard maps and ShakeMap, and FEMA HAZUS- were developed as statistical summaries to match earthquake data from California, Japan, and Taiwan. The 2008 Wells and Mogul events in Nevada showed in particular that the generalized statistical approach taken by ShakeMap cannot match actual data on shaking from earthquakes in the Intermountain West, even to first order. Next-Level ShakeZoning relies on physics and geology to define earthquake shaking hazards, rather than statistics. It follows theoretical and computational developments made over the past 20 years, to capitalize on detailed and specific local data sets to more accurately model the propagation and amplification of earthquake waves through the multiple geologic basins of the Intermountain West. Excellent new data sets are now available for Las Vegas Valley. Clark County, Nevada has completed the nation's very first effort to map earthquake hazard class systematically through an entire urban area using Optim's SeisOpt° ReMi technique, which was adapted for large-scale data collection. Using the new Parcel Map in computing shaking in the Valley for scenario earthquakes is crucial for obtaining realistic predictions of ground motions. In an educational element of the project, a dozen undergraduate students have been computing 50 separate earthquake scenarios affecting Las Vegas Valley, using the Next-Level ShakeZoning process. Despite affecting only the upper 30 meters, the Vs30 geotechnical shear-velocity from the Parcel Map shows clear effects on 3-d shaking predictions computed so far at frequencies from 0.1 Hz up to 1.0 Hz. The effect of the Parcel Map on even the 0.1-Hz waves is prominent even with the large mismatch of wavelength to geotechnical depths. Amplifications and de-amplifications affected by the Parcel Map exceed a factor of two, and are highly dependent on the particular scenario. As well, Parcel Map amplification effects extend into areas not characterized in the Parcel Map. The fully 3-d Next-Level ShakeZoning scenarios show many areas of shaking amplification and de-amplification that USGS ShakeMap scenarios cannot predict. For example, the Frenchman Mountain scenario shows PGV of the two approaches within 15% of each other near the source, but upwards of 200% relative amplification or de-amplification, depending on location, throughout Las Vegas Valley.

Geology and land use in the western part of the Gulf Coast coal-bearing region

USGS Publications Warehouse

Warwick, Peter D.; Aubourg, C.E.; Hook, R.W.; SanFilipo, John R.

2002-01-01

This map series is a compilation of the outcrop geology in the U.S. Gulf Coast coal region. The maps show the regional geologic setting for primary coal occurrences and detailed geology and historic mining areas.The CD contains ESRI ArcView SHP files of cities, urban areas, historical mines (points and polygons), counties, current mines, 1:100,000 quadrangle outlines of the study area, fossil fuel powerplants, nuclear powerplants, political boundaries, federally managed lands, roads and railroads in the study area, hydrology in the study area (polygons and arcs), geology nomenclature breaks, geological features (faults), and geology. ArcExplorer is included on the CD.

A conceptual method for monitoring locust habitat

USGS Publications Warehouse

Howard, Stephen M.; Loveland, Thomas R.; Ohlen, Donald O.; Moore, Donald G.; Gallo, Kevin P.; Olsson, Jonathon

1987-01-01

A procedure to map and monitor vegetation conditions in near-real time was developed at the United States Geological Survey;s Earth Resources Observation Systems Data Center for use in locust control efforts. Meteorological satellite dat were acquired daily for 3 weeks in October and November 1986 over a 1.4-million-square-kilometer study area centered on Botswana in southern Africa. Advanced Very High Resolution Radiometer data were screened to remove cloud-contaminated data and registered to a 1-kilometer geographic base. Each day the normalized difference vegetation index (NDVI) was calculated to determine the presence and relative amounts of green vegetation in the area. Over a 10-day cycle, subsequent dates of NDVI data were composited to fill in data removed by the cloud-screening process. At any pixel location, the maximum NDVI value was retained. At the end of the 10-day cycle, a composite vegetation-greenness map was produced and another cycle started. Greenness-change maps were produced by comparing two 10-day composite greenness images. Automated map production procedures were used to merge the NDVI image data with cartographic data (boundaries, roads, tick marks) digitized from 1:1,000,000-scale operational navigation charts. The vegetation-greenness map shoes the current distribution of vegetation in the region and can be used to locate potential locust breeding area. The change map shows areas where increases and decreases in greenness have occurred between processing cycles. Significant areas of locust damage in remote regions are characterized by an unexpected decrease in greenness. These maps can be used by locust control teams to efficiently target areas for reconnaissance. In general, the procedures and products have utility for resource managers who are required to monitor vegetation resources over large geographic regions.

The pattern of spatial flood disaster region in DKI Jakarta

NASA Astrophysics Data System (ADS)

Tambunan, M. P.

2017-02-01

The study of disaster flood area was conducted in DKI Jakarta Province, Indonesia. The aim of this research is: to study the spatial distribution of potential and actual of flood area The flood was studied from the geographic point of view using spatial approach, while the study of the location, the distribution, the depth and the duration of flooding was conducted using geomorphologic approach and emphasize on the detailed landform unit as analysis unit. In this study the landforms in DKI Jakarta have been a diversity, as well as spatial and temporal pattern of the actual and potential flood area. Landform at DKI Jakarta has been largely used as built up area for settlement and it facilities, thus affecting the distribution pattern of flooding area. The collection of the physical condition of landform in DKI Jakarta data prone were conducted through interpretation of the topographic map / RBI map and geological map. The flood data were obtained by survey and secondary data from Kimpraswil (Public Work) of DKI Jakarta Province for 3 years (1996, 2002, and 2007). Data of rainfall were obtained from BMKG and land use data were obtained from BPN DKI Jakarta. The analysis of the causal factors and distribution of flooding was made spatially and temporally using geographic information system. This study used survey method with a pragmatic approach. In this study landform as result from the analytical survey was settlement land use as result the synthetic survey. The primary data consist of landform, and the flood characteristic obtained by survey. The samples were using purposive sampling. Landform map was composed by relief, structure and material stone, and process data Landform map was overlay with flood map the flood prone area in DKI Jakarta Province in scale 1:50,000 to show. Descriptive analysis was used the spatial distribute of the flood prone area. The result of the study show that actual of flood prone area in the north, west and east of Jakarta lowland both in beach ridge, coastal alluvial plain, and alluvial plain; while the flood potential area on the slope is found flat and steep at alluvial fan, alluvial plain, beach ridge, and coastal alluvial plain in DKI Jakarta. Based on the result can be concluded that actual flood prone is not distributed on potential flood prone

Attention Priority Map of Face Images in Human Early Visual Cortex.

PubMed

Mo, Ce; He, Dongjun; Fang, Fang

2018-01-03

Attention priority maps are topographic representations that are used for attention selection and guidance of task-related behavior during visual processing. Previous studies have identified attention priority maps of simple artificial stimuli in multiple cortical and subcortical areas, but investigating neural correlates of priority maps of natural stimuli is complicated by the complexity of their spatial structure and the difficulty of behaviorally characterizing their priority map. To overcome these challenges, we reconstructed the topographic representations of upright/inverted face images from fMRI BOLD signals in human early visual areas primary visual cortex (V1) and the extrastriate cortex (V2 and V3) based on a voxelwise population receptive field model. We characterized the priority map behaviorally as the first saccadic eye movement pattern when subjects performed a face-matching task relative to the condition in which subjects performed a phase-scrambled face-matching task. We found that the differential first saccadic eye movement pattern between upright/inverted and scrambled faces could be predicted from the reconstructed topographic representations in V1-V3 in humans of either sex. The coupling between the reconstructed representation and the eye movement pattern increased from V1 to V2/3 for the upright faces, whereas no such effect was found for the inverted faces. Moreover, face inversion modulated the coupling in V2/3, but not in V1. Our findings provide new evidence for priority maps of natural stimuli in early visual areas and extend traditional attention priority map theories by revealing another critical factor that affects priority maps in extrastriate cortex in addition to physical salience and task goal relevance: image configuration. SIGNIFICANCE STATEMENT Prominent theories of attention posit that attention sampling of visual information is mediated by a series of interacting topographic representations of visual space known as attention priority maps. Until now, neural evidence of attention priority maps has been limited to studies involving simple artificial stimuli and much remains unknown about the neural correlates of priority maps of natural stimuli. Here, we show that attention priority maps of face stimuli could be found in primary visual cortex (V1) and the extrastriate cortex (V2 and V3). Moreover, representations in extrastriate visual areas are strongly modulated by image configuration. These findings extend our understanding of attention priority maps significantly by showing that they are modulated, not only by physical salience and task-goal relevance, but also by the configuration of stimuli images. Copyright © 2018 the authors 0270-6474/18/380149-09$15.00/0.

A batch sliding window method for local singularity mapping and its application for geochemical anomaly identification

NASA Astrophysics Data System (ADS)

Xiao, Fan; Chen, Zhijun; Chen, Jianguo; Zhou, Yongzhang

2016-05-01

In this study, a novel batch sliding window (BSW) based singularity mapping approach was proposed. Compared to the traditional sliding window (SW) technique with disadvantages of the empirical predetermination of a fixed maximum window size and outliers sensitivity of least-squares (LS) linear regression method, the BSW based singularity mapping approach can automatically determine the optimal size of the largest window for each estimated position, and utilizes robust linear regression (RLR) which is insensitive to outlier values. In the case study, tin geochemical data in Gejiu, Yunnan, have been processed by BSW based singularity mapping approach. The results show that the BSW approach can improve the accuracy of the calculation of singularity exponent values due to the determination of the optimal maximum window size. The utilization of RLR method in the BSW approach can smoothen the distribution of singularity index values with few or even without much high fluctuate values looking like noise points that usually make a singularity map much roughly and discontinuously. Furthermore, the student's t-statistic diagram indicates a strong spatial correlation between high geochemical anomaly and known tin polymetallic deposits. The target areas within high tin geochemical anomaly could probably have much higher potential for the exploration of new tin polymetallic deposits than other areas, particularly for the areas that show strong tin geochemical anomalies whereas no tin polymetallic deposits have been found in them.

Web Based Rapid Mapping of Disaster Areas using Satellite Images, Web Processing Service, Web Mapping Service, Frequency Based Change Detection Algorithm and J-iView

NASA Astrophysics Data System (ADS)

Bandibas, J. C.; Takarada, S.

2013-12-01

Timely identification of areas affected by natural disasters is very important for a successful rescue and effective emergency relief efforts. This research focuses on the development of a cost effective and efficient system of identifying areas affected by natural disasters, and the efficient distribution of the information. The developed system is composed of 3 modules which are the Web Processing Service (WPS), Web Map Service (WMS) and the user interface provided by J-iView (fig. 1). WPS is an online system that provides computation, storage and data access services. In this study, the WPS module provides online access of the software implementing the developed frequency based change detection algorithm for the identification of areas affected by natural disasters. It also sends requests to WMS servers to get the remotely sensed data to be used in the computation. WMS is a standard protocol that provides a simple HTTP interface for requesting geo-registered map images from one or more geospatial databases. In this research, the WMS component provides remote access of the satellite images which are used as inputs for land cover change detection. The user interface in this system is provided by J-iView, which is an online mapping system developed at the Geological Survey of Japan (GSJ). The 3 modules are seamlessly integrated into a single package using J-iView, which could rapidly generate a map of disaster areas that is instantaneously viewable online. The developed system was tested using ASTER images covering the areas damaged by the March 11, 2011 tsunami in northeastern Japan. The developed system efficiently generated a map showing areas devastated by the tsunami. Based on the initial results of the study, the developed system proved to be a useful tool for emergency workers to quickly identify areas affected by natural disasters.

Mapping Norway - a Method to Register and Survey the Status of Accessibility

NASA Astrophysics Data System (ADS)

Michaelis, Sven; Bögelsack, Kathrin

2018-05-01

The Norwegian mapping authority has developed a standard method for mapping accessibility mostly for people with limited or no walking abilities in urban and recreational areas. We choose an object-orientated approach where points, lines and polygons represents objects in the environment. All data are stored in a geospatial database, so they can be presented as web map and analyzed using GIS software. By the end of 2016 more than 160 municipalities are mapped using that method. The aim of this project is to establish a national standard for mapping and to provide a geodatabase that shows the status of accessibility throughout Norway. The data provide a useful tool for national statistics, local planning authorities and private users. First results show that accessibility is low and Norway still faces many challenges to meet the government's goals for Universal Design.

Quantitative assessment of urban wetland dynamics using high spatial resolution satellite imagery between 2000 and 2013.

PubMed

Hu, Tangao; Liu, Jiahong; Zheng, Gang; Li, Yao; Xie, Bin

2018-05-09

Accurate and timely information describing urban wetland resources and their changes over time, especially in rapidly urbanizing areas, is becoming more important. We applied an object-based image analysis and nearest neighbour classifier to map and monitor changes in land use/cover using multi-temporal high spatial resolution satellite imagery in an urban wetland area (Hangzhou Xixi Wetland) from 2000, 2005, 2007, 2009 and 2013. The overall eight-class classification accuracies averaged 84.47% for the five years. The maps showed that between 2000 and 2013 the amount of non-wetland (urban) area increased by approximately 100%. Herbaceous (32.22%), forest (29.57%) and pond (23.85%) are the main land-cover types that changed to non-wetland, followed by cropland (6.97%), marsh (4.04%) and river (3.35%). In addition, the maps of change patterns showed that urban wetland loss is mainly distributed west and southeast of the study area due to real estate development, and the greatest loss of urban wetlands occurred from 2007 to 2013. The results demonstrate the advantages of using multi-temporal high spatial resolution satellite imagery to provide an accurate, economical means to map and analyse changes in land use/cover over time and the ability to use the results as inputs to urban wetland management and policy decisions.

Domestic well locations and populations served in the contiguous U.S.: 1990

USGS Publications Warehouse

Johnson, Tyler; Belitz, Kenneth

2017-01-01

We estimate the location and population served by domestic wells in the contiguous United States in two ways: (1) the “Block Group Method” or BGM, uses data from the 1990 census, and (2) the “Road-Enhanced Method” or REM, refines the locations by using a buffer expansion and shrinkage technique along roadways to define areas where domestic wells exist. The fundamental assumption is that houses (and therefore domestic wells) are located near a named road. The results are presented as two nationally-consistent domestic-well population datasets.While both methods can be considered valid, the REM map is more precise in locating domestic wells; the REM map has a smaller amount of spatial bias (Type 1 and Type 2 errors nearly equal vs biased in Type 1), total error (10.9% vs 23.7%), and distance error (2.0 km vs 2.7 km), when comparing the REM and BGM maps to a calibration map in California. However, the BGM map is more inclusive of all potential locations for domestic wells. Independent domestic well datasets from the USGS, and the States of MN, NV, and TX show that the BGM captures about 5 to 10% more wells than the REM.One key difference between the BGM and the REM is the mapping of low density areas. The REM reduces areas mapped as low density by 57%, concentrating populations into denser regions. Therefore, if one is trying to capture all of the potential areas of domestic-well usage, then the BGM map may be more applicable. If location is more imperative, then the REM map is better at identifying areas of the landscape with the highest probability of finding a domestic well. Depending on the purpose of a study, a combination of both maps can be used.

Flooding risks: a comparison of lay people's perceptions and expert's assessments in Switzerland.

PubMed

Siegrist, Michael; Gutscher, Heinz

2006-08-01

Experts on the risk of flooding have developed very detailed maps for different parts of Switzerland that indicate the types of damage possible and the probabilities of adverse events. Four categories of risk severity are defined on the maps, ranging from high risk to no risk. Based on these existing maps, we selected respondents for a mail survey, some from areas high in risk and others from low-risk regions. Respondents answered several questions related to flood risk perception and preparedness. Survey results showed that respondents' risk perceptions were correlated with the experts' risk assessments. Respondents who lived in areas designated "no risk" by the experts had lower perceptions of risk than respondents who lived in areas with higher levels of designated risk. With regard to concrete prevention behavior, no differences between people living in different risk areas were observed. Survey results further suggest that many inhabitants do not know that flooding maps exist for their region. Results suggest that in some regions people overestimate the risks associated with flooding. Consequently, some people are more afraid of flooding than is justified by the facts. Some people show prevention behavior that most likely is superfluous. However, in other regions people underestimate the risks associated with flooding. These people do not show prevention behavior, and they are not well prepared for an adverse event. Furthermore, results suggest that respondents' experiences with flooding are positively related to their perceptions of flood risk. Findings of the present study are in line with the availability heuristic.

Reserve networks based on richness hotspots and representation vary with scale.

PubMed

Shriner, Susan A; Wilson, Kenneth R; Flather, Curtis H

2006-10-01

While the importance of spatial scale in ecology is well established, few studies have investigated the impact of data grain on conservation planning outcomes. In this study, we compared species richness hotspot and representation networks developed at five grain sizes. We used species distribution maps for mammals and birds developed by the Arizona and New Mexico Gap Analysis Programs (GAP) to produce 1-km2, 100-kmn2, 625-km2, 2500-km2, and 10,000-km2 grid cell resolution distribution maps. We used these distribution maps to generate species richness and hotspot (95th quantile) maps for each taxon in each state. Species composition information at each grain size was used to develop two types of representation networks using the reserve selection software MARXAN. Reserve selection analyses were restricted to Arizona birds due to considerable computation requirements. We used MARXAN to create best reserve networks based on the minimum area required to represent each species at least once and equal area networks based on irreplaceability values. We also measured the median area of each species' distribution included in hotspot (mammals and birds of Arizona and New Mexico) and irreplaceability (Arizona birds) networks across all species. Mean area overlap between richness hotspot reserves identified at the five grain sizes was 29% (grand mean for four within-taxon/state comparisons), mean overlap for irreplaceability reserve networks was 32%, and mean overlap for best reserve networks was 53%. Hotspots for mammals and birds showed low overlap with a mean of 30%. Comparison of hotspots and irreplaceability networks showed very low overlap with a mean of 13%. For hotspots, median species distribution area protected within reserves declined monotonically from a high of 11% for 1-km2 networks down to 6% for 10,000-km2 networks. Irreplaceability networks showed a similar, but more variable, pattern of decline. This work clearly shows that map resolution has a profound effect on conservation planning outcomes and that hotspot and representation outcomes may be strikingly dissimilar. Thus, conservation planning is scale dependent, such that reserves developed using coarse-grained data do not subsume fine-grained reserves. Moreover, preserving both full species representation and species rich areas may require combined reserve design strategies.

Interdisciplinary applications and interpretations of ERTS data within the Susquehanna River Basin; resources inventory, land use and pollution

NASA Technical Reports Server (NTRS)

Mcmurtry, G. J. (Principal Investigator)

1973-01-01

The author has identified the following significant results. Identification and mapping of three major kinds of coal refuse targets based on spectral signatures in channels four through seven of the ERTS-1 MSS were conducted. Correlation of the placement of the coal refuse targets with an existing map of their location was accomplished. Digital processing of ERTS-1 data permitted identification of stripped areas including ones that are not discernible by visual analysis of ERTS imagery. Combined visual and digital techniques of analyzing ERTS-1 data for geologic formations have been tried on selected areas of Pennsylvania. Mapping of two major agriculture counties to show land forms, drainage patterns, water, and urban areas were made using positive transparencies of MSS data. Two frames of the same central Pennsylvania area were brought into registration by translation and then merged even though the frames were obtained 71 days apart.

A GIS-BASED MULTI-CRITERIA EVALUATION SYSTEM FOR SELECTION OF LANDFILL SITES: a case study from Abu Dhabi, United Arab Emirates

NASA Astrophysics Data System (ADS)

Issa, S. M.; Shehhi, B. Al

2012-07-01

Landfill sites receive 92% of total annual solid waste produced by municipalities in the emirate of Abu Dhabi. In this study, candidate sites for an appropriate landfill location for the Abu Dhabi municipal area are determined by integrating geographic information systems (GIS) and multi-criteria evaluation (MCE) analysis. To identify appropriate landfill sites, eight input map layers including proximity to urban areas, proximity to wells and water table depth, geology and topography, proximity to touristic and archeological sites, distance from roads network, distance from drainage networks, and land slope are used in constraint mapping. A final map was generated which identified potential areas showing suitability for the location of the landfill site. Results revealed that 30% of the study area was identified as highly suitable, 25% as suitable, and 45% as unsuitable. The selection of the final landfill site, however, requires further field research.

Mapping regional patterns of large forest fires in Wildland-Urban Interface areas in Europe.

PubMed

Modugno, Sirio; Balzter, Heiko; Cole, Beth; Borrelli, Pasquale

2016-05-01

Over recent decades, Land Use and Cover Change (LUCC) trends in many regions of Europe have reconfigured the landscape structures around many urban areas. In these areas, the proximity to landscape elements with high forest fuels has increased the fire risk to people and property. These Wildland-Urban Interface areas (WUI) can be defined as landscapes where anthropogenic urban land use and forest fuel mass come into contact. Mapping their extent is needed to prioritize fire risk control and inform local forest fire risk management strategies. This study proposes a method to map the extent and spatial patterns of the European WUI areas at continental scale. Using the European map of WUI areas, the hypothesis is tested that the distance from the nearest WUI area is related to the forest fire probability. Statistical relationships between the distance from the nearest WUI area, and large forest fire incidents from satellite remote sensing were subsequently modelled by logistic regression analysis. The first European scale map of the WUI extent and locations is presented. Country-specific positive and negative relationships of large fires and the proximity to the nearest WUI area are found. A regional-scale analysis shows a strong influence of the WUI zones on large fires in parts of the Mediterranean regions. Results indicate that the probability of large burned surfaces increases with diminishing WUI distance in touristic regions like Sardinia, Provence-Alpes-Côte d'Azur, or in regions with a strong peri-urban component as Catalunya, Comunidad de Madrid, Comunidad Valenciana. For the above regions, probability curves of large burned surfaces show statistical relationships (ROC value > 0.5) inside a 5000 m buffer of the nearest WUI. Wise land management can provide a valuable ecosystem service of fire risk reduction that is currently not explicitly included in ecosystem service valuations. The results re-emphasise the importance of including this ecosystem service in landscape valuations to account for the significant landscape function of reducing the risk of catastrophic large fires. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Application of remote sensing technology to the solution of problems in the management of resources in Indiana

NASA Technical Reports Server (NTRS)

Weismiller, R. A.; Mroczynski, R. P. (Principal Investigator)

1977-01-01

The author has identified the following significant results. The Lydick, South Bend West, South Bend East, and Osceola quadrangles were successfully classified into twenty-six cover types with a high degree of accuracy. The ability of this computer-assisted classification system to delineate various stages of urban development, from heavy industry to new suburban development, was of particular interest to the planning commission. The classification is clearly more beneficial than the existing agricultural soils and topographic maps, because it shows the current ground cover conditions all on one map. It shows how an area is developing along with the specific type and location of new development. The classification also shows at a glance whether development is taking place in an area suitable for development or if growth is taking place in prime agricultural land, areas of poor foundation material, or other places where development is not desirable.

EnviroAtlas - Austin, TX - Atlas Area Boundary

EPA Pesticide Factsheets

This EnviroAtlas dataset shows the boundary of the Austin, TX Atlas Area. It represents the outside edge of all the block groups included in the EnviroAtlas Area.This dataset was produced by the US EPA to support research and online mapping activities related to EnviroAtlas. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the contiguous United States. The dataset is available as downloadable data (https://edg.epa.gov/data/Public/ORD/EnviroAtlas) or as an EnviroAtlas map service. Additional descriptive information about each attribute in this dataset can be found in its associated EnviroAtlas Fact Sheet (https://www.epa.gov/enviroatlas/enviroatlas-fact-sheets).

Inventory and mapping of flood inundation using interactive digital image analysis techniques

USGS Publications Warehouse

Rohde, Wayne G.; Nelson, Charles A.; Taranik, J.V.

1979-01-01

LANDSAT digital data and color infra-red photographs were used in a multiphase sampling scheme to estimate the area of agricultural land affected by a flood. The LANDSAT data were classified with a maximum likelihood algorithm. Stratification of the LANDSAT data, prior to classification, greatly reduced misclassification errors. The classification results were used to prepare a map overlay showing the areal extent of flooding. These data also provided statistics required to estimate sample size in a two phase sampling scheme, and provided quick, accurate estimates of areas flooded for the first phase. The measurements made in the second phase, based on ground data and photo-interpretation, were used with two phase sampling statistics to estimate the area of agricultural land affected by flooding These results show that LANDSAT digital data can be used to prepare map overlays showing the extent of flooding on agricultural land and, with two phase sampling procedures, can provide acreage estimates with sampling errors of about 5 percent. This procedure provides a technique for rapidly assessing the areal extent of flood conditions on agricultural land and would provide a basis for designing a sampling framework to estimate the impact of flooding on crop production.

Map showing surface ruptures associated with the Mammoth Lakes, California, earthquakes of May 1980

USGS Publications Warehouse

Clark, M.M.; Yount, J.C.; Vaughn, P.R.; Zepeda, R.L.

1982-01-01

This map shows surface ruptures associated with the M 6 Mammoth Lakes earthquakes of May 25-27, 1980 (Sherburne, 1980). The ruptures were mapped during USGS field investigations May 28 to June 4 and July 14-19, 1980. The map also includes some of the ruptures recorded by California Division of Mines and Geology investigators May 26-31, June 26-27, and July 7-11, 1980 (Taylor and Bryant, 1980). Because most of the surface ruptures developed in either unconsolidated pumice, alluvium, or till (and many were on slopes of scarps created by earlier faulting), wind, rain and animals quickly erased many of the ruptures. In places, the minimum detectable slip was 3-10 mm. Thus the lines on the map do not record all of the ruptures that formed at the time of the earthquake. Many of the areas were we show gaps between lines on the map probably had cracks originally. 

Retrieval and Mapping of Heavy Metal Concentration in Soil Using Time Series Landsat 8 Imagery

NASA Astrophysics Data System (ADS)

Fang, Y.; Xu, L.; Peng, J.; Wang, H.; Wong, A.; Clausi, D. A.

2018-04-01

Heavy metal pollution is a critical global environmental problem which has always been a concern. Traditional approach to obtain heavy metal concentration relying on field sampling and lab testing is expensive and time consuming. Although many related studies use spectrometers data to build relational model between heavy metal concentration and spectra information, and then use the model to perform prediction using the hyperspectral imagery, this manner can hardly quickly and accurately map soil metal concentration of an area due to the discrepancies between spectrometers data and remote sensing imagery. Taking the advantage of easy accessibility of Landsat 8 data, this study utilizes Landsat 8 imagery to retrieve soil Cu concentration and mapping its distribution in the study area. To enlarge the spectral information for more accurate retrieval and mapping, 11 single date Landsat 8 imagery from 2013-2017 are selected to form a time series imagery. Three regression methods, partial least square regression (PLSR), artificial neural network (ANN) and support vector regression (SVR) are used to model construction. By comparing these models unbiasedly, the best model are selected to mapping Cu concentration distribution. The produced distribution map shows a good spatial autocorrelation and consistency with the mining area locations.

Geologic map of the Boulder-Fort Collins-Greeley Area, Colorado

USGS Publications Warehouse

Colton, Roger B.

1978-01-01

This digital map shows the geographic extent of rock stratigraphic units (formations) as compiled by Colton in 1976 under the Front Range Urban Corridor Geology Program. Colton used his own geologic mapping and previously published geologic maps to compile one map having a single classification of geologic units. The resulting published color paper map (USGS Map I-855-G, Colton, 1978) was intended for land-use planning and to depict the regional geology. In 1997-1999, another USGS project designed to address urban growth issues was undertaken. This project, the USGS Front Range Infrastructure Resources Project, undertook to digitize Colton's map at 1:100,000 scale, making it useable in Geographical Information Systems (GIS). That product is described here. In general, the digitized map depicts in its western part Precambrian igneous and metamorphic rocks, Pennsylvanian and younger sedimentary rock units, major faults, and brecciated zones along an eastern strip (5-20 km wide) of the Front Range. The central and eastern parts of the map (Colorado Piedmont) show a mantle of Quaternary unconsolidated deposits and interspersed outcrops of sedimentary rock of Cretaceous or Tertiary age. A surficial mantle of unconsolidated deposits of Quaternary age is differentiated and depicted as eolium (wind-blown sand and silt), alluvium (river gravel, sand, and silt of variable composition), colluvium, and a few landslide deposits. At the mountain front, north-trending, Paleozoic and Mesozoic formations of sandstone, shale, and minor limestone dip mostly eastward and form folds, fault blocks, hogbacks and intervening valleys. Local dikes and sills of Tertiary rhyodacite and basalt intrude rocks near the range front, mostly in the Boulder area.

Speaker Invariance for Phonetic Information: an fMRI Investigation

PubMed Central

Salvata, Caden; Blumstein, Sheila E.; Myers, Emily B.

2012-01-01

The current study explored how listeners map the variable acoustic input onto a common sound structure representation while being able to retain phonetic detail to distinguish among the identity of talkers. An adaptation paradigm was utilized to examine areas which showed an equal neural response (equal release from adaptation) to phonetic change when spoken by the same speaker and when spoken by two different speakers, and insensitivity (failure to show release from adaptation) when the same phonetic input was spoken by a different speaker. Neural areas which showed speaker invariance were located in the anterior portion of the middle superior temporal gyrus bilaterally. These findings provide support for the view that speaker normalization processes allow for the translation of a variable speech input to a common abstract sound structure. That this process appears to occur early in the processing stream, recruiting temporal structures, suggests that this mapping takes place prelexically, before sound structure input is mapped on to lexical representations. PMID:23264714

Surficial Geologic Map of the Clinton-Concord-Grafton-Medfield 12-Quadrangle Area in East Central Massachusetts

USGS Publications Warehouse

Stone, Janet R.; Stone, Byron D.

2006-01-01

The surficial geologic map shows the distribution of nonlithified earth materials at land surface in an area of twelve 7.5-minute quadrangles (total 660 square miles) in east-central Massachusetts. The geologic map differentiates surficial materials of Quaternary age on the basis of their lithologic characteristics (grain size, sedimentary structures, mineral and rock-particle composition), constructional geomorphic features, stratigraphic relationships, and age. Surficial earth materials significantly affect human use of the land, and an accurate description of their distribution is particularly important for water resources, construction aggregate resources, earth-surface hazards assessments, and land-use decisions. This compilation of surficial geologic materials is an interim product that defines the areas of exposed bedrock, and the boundaries between glacial till, glacial stratified deposits, and overlying postglacial deposits. This work is part of a comprehensive study to produce a statewide digital map of the surficial geology at a 1:24,000-scale level of accuracy. This report includes explanatory text (PDF), a regional map at 1:50,000 scale (PDF), quadrangle maps at 1:24,000 scale (12 PDF files), GIS data layers (ArcGIS shapefiles), scanned topographic base maps (TIF), metadata for the GIS layers, and a readme.txt file.

Remote sensing applied to land-use studies in Wyoming

NASA Technical Reports Server (NTRS)

Breckenridge, R. M.; Marrs, R. W.; Murphy, D. J.

1973-01-01

Impending development of Wyoming's vast fuel resources requires a quick and efficient method of land use inventory and evaluation. Preliminary evaluations of ERTS-1 imagery have shown that physiographic and land use inventory maps can be compiled by using a combination of visual and automated interpretation techniques. Test studies in the Powder River Basin showed that ERTS image interpretations can provide much of the needed physiographic and land use information. Water impoundments as small as one acre were detected and water bodies larger than five acres could be mapped and their acreage estimated. Flood plains and irrigated lands were successfully mapped, and some individual crops were identified and mapped. Coniferous and deciduous trees were mapped separately using color additive analysis on the ERTS multispectral imagery. Gross soil distinctions were made with the ERTS imagery, and were found to be closely related to the bedrock geology. Several broad unstable areas were identified. These were related to specific geologic and slope conditions and generally extended through large regions. Some new oil fields and all large open-cut coal mines were mapped. The most difficult task accomplished was that of mapping urban areas. Work in the urban areas provides a striking example of snow enhancement and the detail available from a snow enhanced image.

Potentiometric surface of the Minnekahta Aquifer in the Black Hills area, South Dakota

USGS Publications Warehouse

Strobel, Michael L.; Galloway, Joel M.; Hamade, Ghaith R.; Jarrell, Gregory J.

2000-01-01

This map is a product of the Black Hills Hydrology Study, which was initiated in 1990 to assess the quantity, quality, and distribution of surface water and ground water in the Black Hills area of South Dakota (Driscoll, 1992). This long-term study is a cooperative effort between the U.S. Geological Survey (USGS), the South Dakota Department of Environment and Natural Resources, and the West Dakota Water Development District, which represents various local and county cooperators. This map is part of a series of 1:100,000-scale maps for the study. The maps include a hydrogeologic map, structure-contour maps (altitudes of the tops of formations) for five formations that contain major aquifers in the study area, and potentiometric maps for these five major aquifers (the Inyan Kara, Minnekahta, Minnelusa, Madison, and Deadwood aquifers).The study area consists of the topographically defined Black Hills and adjacent areas located in western South Dakota. The Black Hills area is an elongated, dome-shaped feature, about 125 miles long and 60 miles wide, which was uplifted during the Laramide orogeny (Feldman and Heimlich, 1980). The oldest geologic units in the study area are Precambrian metamorphic and igneous rocks, which are exposed in the central core of the Black Hills. Surrounding the Precambrian core is a layered series of sedimentary rocks including limestones, sandstones, and shales that are exposed in roughly concentric rings around the uplifted flanks of the Black Hills. The bedrock sedimentary units typically dip away from the uplifted Black Hills at angles that approach or exceed 10 degrees near the outcrops, and decrease with distance from the uplift. Many of the sedimentary units contain aquifers, both within and beyond the study area. Recharge to these aquifers occurs from infiltration of precipitation upon the outcrops and, in some cases, from infiltration of streamflow (Hortness and Driscoll, 1998). Artesian conditions generally exist within these aquifers where an upper confining layer is present. Flowing wells and springs that originate from the confined aquifers are common around the periphery of the Black Hills.The purpose of this map is to show the potentiometric surface of the Minnekahta aquifer within the study area. The map provides a tool for evaluating ground-water flow directions and hydraulic gradients in the Minnekahta aquifer.

Potentiometric surface of the Inyan Kara Aquifer in the Black Hills area, South Dakota

USGS Publications Warehouse

Strobel, Michael L.; Galloway, Joel M.; Hamade, Ghaith R.; Jarrell, Gregory J.

2000-01-01

This map is a product of the Black Hills Hydrology Study, which was initiated in 1990 to assess the quantity, quality, and distribution of surface water and ground water in the Black Hills area of South Dakota (Driscoll, 1992). This long-term study is a cooperative effort between the U.S. Geological Survey (USGS), the South Dakota Department of Environment and Natural Resources, and the West Dakota Water Development District, which represents various local and county cooperators. This map is part of a series of 1:100,000-scale maps for the study. The maps include a hydrogeologic map, structure-contour maps (altitudes of the tops of formations) for five formations that contain major aquifers in the study area, and potentiometric maps for these five major aquifers (the Inyan Kara, Minnekahta, Minnelusa, Madison, and Deadwood aquifers).The study area consists of the topographically defined Black Hills and adjacent areas located in western South Dakota. The Black Hills area is an elongated, dome-shaped feature, about 125 miles long and 60 miles wide, which was uplifted during the Laramide orogeny (Feldman and Heimlich, 1980). The oldest geologic units in the study area are Precambrian metamorphic and igneous rocks, which are exposed in the central core of the Black Hills. Surrounding the Precambrian core is a layered series of sedimentary rocks including limestones, sandstones, and shales that are exposed in roughly concentric rings around the uplifted flanks of the Black Hills. The bedrock sedimentary units typically dip away from the uplifted Black Hills at angles that approach or exceed 10 degrees near the outcrops, and decrease with distance from the uplift. Many of the sedimentary units contain aquifers, both within and beyond the study area. Recharge to these aquifers occurs from infiltration of precipitation upon the outcrops and, in some cases, from infiltration of streamflow (Hortness and Driscoll, 1998). Artesian conditions generally exist within these aquifers where an upper confining layer is present. Flowing wells and springs that originate from the confined aquifers are common around the periphery of the Black Hills.The purpose of this map is to show the potentiometric surface of the Inyan Kara aquifer within the study area. The map provides a tool for evaluating ground-water flow directions and hydraulic gradients in the Inyan Kara aquifer.

Potentiometric surface of the Deadwood Aquifer in the Black Hills area, South Dakota

USGS Publications Warehouse

Strobel, Michael L.; Galloway, Joel M.; Hamade, Ghaith R.; Jarrell, Gregory J.

2000-01-01

This map is a product of the Black Hills Hydrology Study, which was initiated in 1990 to assess the quantity, quality, and distribution of surface water and ground water in the Black Hills area of South Dakota (Driscoll, 1992). This long-term study is a cooperative effort between the U.S. Geological Survey (USGS), the South Dakota Department of Environment and Natural Resources, and the West Dakota Water Development District, which represents various local and county cooperators. This map is part of a series of 1:100,000-scale maps for the study. The maps include a hydrogeologic map, structure-contour maps (altitudes of the tops of formations) for five formations that contain major aquifers in the study area, and potentiometric maps for these five major aquifers (the Inyan Kara, Minnekahta, Minnelusa, Madison, and Deadwood aquifers).The study area consists of the topographically defined Black Hills and adjacent areas located in western South Dakota. The Black Hills area is an elongated, dome-shaped feature, about 125 miles long and 60 miles wide, which was uplifted during the Laramide orogeny (Feldman and Heimlich, 1980). The oldest geologic units in the study area are Precambrian metamorphic and igneous rocks, which are exposed in the central core of the Black Hills. Surrounding the Precambrian core is a layered series of sedimentary rocks including limestones, sandstones, and shales that are exposed in roughly concentric rings around the uplifted flanks of the Black Hills. The bedrock sedimentary units typically dip away from the uplifted Black Hills at angles that approach or exceed 10 degrees near the outcrops, and decrease with distance from the uplift. Many of the sedimentary units contain aquifers, both within and beyond the study area. Recharge to these aquifers occurs from infiltration of precipitation upon the outcrops and, in some cases, from infiltration of streamflow (Hortness and Driscoll, 1998). Artesian conditions generally exist within these aquifers where an upper confining layer is present. Flowing wells and springs that originate from the confined aquifers are common around the periphery of the Black Hills.The purpose of this map is to show the potentiometric surface of the Deadwood aquifer within the study area. The map provides a tool for evaluating ground-water flow directions and hydraulic gradients in the Deadwood aquifer.

Potentiometric surface of the Minnelusa Aquifer in the Black Hills area, South Dakota

USGS Publications Warehouse

Strobel, Michael L.; Galloway, Joel M.; Hamade, Ghaith R.; Jarrell, Gregory J.

2000-01-01

This map is a product of the Black Hills Hydrology Study, which was initiated in 1990 to assess the quantity, quality, and distribution of surface water and ground water in the Black Hills area of South Dakota (Driscoll, 1992). This long-term study is a cooperative effort between the U.S. Geological Survey (USGS), the South Dakota Department of Environment and Natural Resources, and the West Dakota Water Development District, which represents various local and county cooperators. This map is part of a series of 1:100,000-scale maps for the study. The maps include a hydrogeologic map, structure-contour maps (altitudes of the tops of formations) for five formations that contain major aquifers in the study area, and potentiometric maps for these five major aquifers (the Inyan Kara, Minnekahta, Minnelusa, Madison, and Deadwood aquifers).The study area consists of the topographically defined Black Hills and adjacent areas located in western South Dakota. The Black Hills area is an elongated, dome-shaped feature, about 125 miles long and 60 miles wide, which was uplifted during the Laramide orogeny (Feldman and Heimlich, 1980). The oldest geologic units in the study area are Precambrian metamorphic and igneous rocks, which are exposed in the central core of the Black Hills. Surrounding the Precambrian core is a layered series of sedimentary rocks including limestones, sandstones, and shales that are exposed in roughly concentric rings around the uplifted flanks of the Black Hills. The bedrock sedimentary units typically dip away from the uplifted Black Hills at angles that approach or exceed 10 degrees near the outcrops, and decrease with distance from the uplift. Many of the sedimentary units contain aquifers, both within and beyond the study area. Recharge to these aquifers occurs from infiltration of precipitation upon the outcrops and, in some cases, from infiltration of streamflow (Hortness and Driscoll, 1998). Artesian conditions generally exist within these aquifers where an upper confining layer is present. Flowing wells and springs that originate from the confined aquifers are common around the periphery of the Black Hills.The purpose of this map is to show the potentiometric surface of the Minnelusa aquifer within the study area. The map provides a tool for evaluating ground-water flow directions and hydraulic gradients in the Minnelusa aquifer.

Potentiometric surface of the Madison Aquifer in the Black Hills area, South Dakota

USGS Publications Warehouse

Strobel, Michael L.; Galloway, Joel M.; Hamade, Ghaith R.; Jarrell, Gregory L.

2000-01-01

This map is a product of the Black Hills Hydrology Study, which was initiated in 1990 to assess the quantity, quality, and distribution of surface water and ground water in the Black Hills area of South Dakota (Driscoll, 1992). This long-term study is a cooperative effort between the U.S. Geological Survey (USGS), the South Dakota Department of Environment and Natural Resources, and the West Dakota Water Development District, which represents various local and county cooperators. This map is part of a series of 1:100,000-scale maps for the study. The maps include a hydrogeologic map, structure-contour maps (altitudes of the tops of formations) for five formations that contain major aquifers in the study area, and potentiometric maps for these five major aquifers (the Inyan Kara, Minnekahta, Minnelusa, Madison, and Deadwood aquifers).The study area consists of the topographically defined Black Hills and adjacent areas located in western South Dakota. The Black Hills area is an elongated, dome-shaped feature, about 125 miles long and 60 miles wide, which was uplifted during the Laramide orogeny (Feldman and Heimlich, 1980). The oldest geologic units in the study area are Precambrian metamorphic and igneous rocks, which are exposed in the central core of the Black Hills. Surrounding the Precambrian core is a layered series of sedimentary rocks including limestones, sandstones, and shales that are exposed in roughly concentric rings around the uplifted flanks of the Black Hills. The bedrock sedimentary units typically dip away from the uplifted Black Hills at angles that approach or exceed 10 degrees near the outcrops, and decrease with distance from the uplift. Many of the sedimentary units contain aquifers, both within and beyond the study area. Recharge to these aquifers occurs from infiltration of precipitation upon the outcrops and, in some cases, from infiltration of streamflow (Hortness and Driscoll, 1998). Artesian conditions generally exist within these aquifers where an upper confining layer is present. Flowing wells and springs that originate from the confined aquifers are common around the periphery of the Black Hills.The purpose of this map is to show the potentiometric surface of the Madison aquifer within the study area. The map provides a tool for evaluating ground-water flow directions and hydraulic gradients in the Madison aquifer.

Explicit area-based accuracy assessment for mangrove tree crown delineation using Geographic Object-Based Image Analysis (GEOBIA)

NASA Astrophysics Data System (ADS)

Kamal, Muhammad; Johansen, Kasper

2017-10-01

Effective mangrove management requires spatially explicit information of mangrove tree crown map as a basis for ecosystem diversity study and health assessment. Accuracy assessment is an integral part of any mapping activities to measure the effectiveness of the classification approach. In geographic object-based image analysis (GEOBIA) the assessment of the geometric accuracy (shape, symmetry and location) of the created image objects from image segmentation is required. In this study we used an explicit area-based accuracy assessment to measure the degree of similarity between the results of the classification and reference data from different aspects, including overall quality (OQ), user's accuracy (UA), producer's accuracy (PA) and overall accuracy (OA). We developed a rule set to delineate the mangrove tree crown using WorldView-2 pan-sharpened image. The reference map was obtained by visual delineation of the mangrove tree crowns boundaries form a very high-spatial resolution aerial photograph (7.5cm pixel size). Ten random points with a 10 m radius circular buffer were created to calculate the area-based accuracy assessment. The resulting circular polygons were used to clip both the classified image objects and reference map for area comparisons. In this case, the area-based accuracy assessment resulted 64% and 68% for the OQ and OA, respectively. The overall quality of the calculation results shows the class-related area accuracy; which is the area of correctly classified as tree crowns was 64% out of the total area of tree crowns. On the other hand, the overall accuracy of 68% was calculated as the percentage of all correctly classified classes (tree crowns and canopy gaps) in comparison to the total class area (an entire image). Overall, the area-based accuracy assessment was simple to implement and easy to interpret. It also shows explicitly the omission and commission error variations of object boundary delineation with colour coded polygons.

Visual Field Map Clusters in Macaque Extrastriate Visual Cortex

PubMed Central

Kolster, Hauke; Mandeville, Joseph B.; Arsenault, John T.; Ekstrom, Leeland B.; Wald, Lawrence L.; Vanduffel, Wim

2009-01-01

The macaque visual cortex contains more than 30 different functional visual areas, yet surprisingly little is known about the underlying organizational principles that structure its components into a complete ‘visual’ unit. A recent model of visual cortical organization in humans suggests that visual field maps are organized as clusters. Clusters minimize axonal connections between individual field maps that represent common visual percepts, with different clusters thought to carry out different functions. Experimental support for this hypothesis, however, is lacking in macaques, leaving open the question of whether it is unique to humans or a more general model for primate vision. Here we show, using high-resolution BOLD fMRI data in the awake monkey at 7 Tesla, that area MT/V5 and its neighbors are organized as a cluster with a common foveal representation and a circular eccentricity map. This novel view on the functional topography of area MT/V5 and satellites indicates that field map clusters are evolutionarily preserved and may be a fundamental organizational principle of the old world primate visual cortex. PMID:19474330

A temperature and vegetation adjusted NTL urban index for urban area mapping and analysis

NASA Astrophysics Data System (ADS)

Zhang, Xiya; Li, Peijun

2018-01-01

Accurate and timely information regarding the extent and spatial distribution of urban areas on regional and global scales is crucially important for both scientific and policy-making communities. Stable nighttime light (NTL) data from the Defense Meteorological Satellite Program (DMSP) Operational Linescan System (OLS) provides a unique proxy of human settlement and activity, which has been used in the mapping and analysis of urban areas and urbanization dynamics. However, blooming and saturation effects of DMSP/OLS NTL data are two unresolved problems in regional urban area mapping and analysis. This study proposed a new urban index termed the Temperature and Vegetation Adjusted NTL Urban Index (TVANUI). It is intended to reduce blooming and saturation effects and to enhance urban features by combining DMSP/OLS NTL data with Normalized Difference Vegetation Index (NDVI) and land surface temperature (LST) data from the Moderate Resolution Imaging Spectroradiometer onboard the Terra satellite. The proposed index was evaluated in two study areas by comparison with established urban indices. The results demonstrated the proposed TVANUI was effective in enhancing the variation of DMSP/OLS light in urban areas and in reducing blooming and saturation effects, showing better performance than three established urban indices. The TVANUI also significantly outperformed the established urban indices in urban area mapping using both the global-fixed threshold and the local-optimal threshold methods. Thus, the proposed TVANUI provides a useful variable for urban area mapping and analysis on regional scale, as well as for urbanization dynamics using time-series DMSP/OLS and related satellite data.

Clay deposits of the Connecticut River Valley, Connecticut: a special problem in land management

USGS Publications Warehouse

Langer, William H.

1972-01-01

When man first settled the United States, two natural features favored settlement; flat land that was easy to build on and to farm, and a nearby river that could act as a source of water, transportation, and power. The Connecticut River Valley from Middletown, Ct. north past the Connecticut-Massachusetts state line satisfied these two needs, and was favored by many early Americans in New England. This area remains an area of rapid urbanization, partly because of the broad flat lowlands. The subdued topography of this area is due in large part to deposition of fine-grained materials into glacial Lake Hitchcock. This lake was formed during the Wisconsinan age when southward drainage in the Triassic valley of Connecticut was dammed by glacial drift in the area of Rocky Hill, Connecticut. Lake Hitchcock grew to and beyond St. Johnsbury, Vt. with much of the lake being filled with cyclical lake-bottom deposits during the 2,290 to 2,350 years of its life. Aside from the relative flatness inherent in the deposition of fine-grained lake-bottom deposits, these deposits present very few characteristics that are favorable for urbanization. Favorable characteristics are possible sources of clay for manufacturing and possible sources for waste storage sites. Unfavorable characteristics include low water yields resulting in poor urban water-supply sources, and very low flows in streams during dry periods; low percolation rates resulting In drainage and septic problems; and low or uneven bearing strength which create problems in construction. Fine-grained lake-bottom deposits have been mapped for six quadrangles in the Connecticut Valley lowlands; the quadrangles of Windsor Locks, Broad Brook, Hartford North, Manchester, Hartford South, and Glastonbury (all located in Connecticut). All the maps were prepared from existing information including well and test hole data on file at the Water Resources Division in Hartford, surficial geologic quadrangle maps, and bedrock contour maps. The maps also reflect geologic interpretations of the history of glacial Lake Hitchcock. The Hartford North maps were prepared as test maps to determine if the project was feasible. They were prepared using the previously described information plus additional subsurface data obtained from engineering firms and the State Highway Department. During preparation of the maps, an arcuate-shaped, ice-contact deposit composed of coarse sand and gravel was delineated in the Broad Brook and Windsor Locks quadrangles. This feature marks the location of a zone of stagnant ice In front of and marginal to active ice to the north. Two types of maps were prepared for the area in study; Thickness of the Principal Clay Deposit, and Thickness of Material Overlying the Principal Clay Deposit. The term "principal clay deposit" refers to the fine-grained lake-bottom deposits of Glacial Lake Hitchcock. These maps define the distribution of the deposit, and show the thickness of the deposit in 50 foot intervals and the thickness of the material overlying the deposit In 20 foot intervals. The maps indicate that much of the area is underlain with substantial thicknesses of finegrained lake-bottom deposits (50 feet thick or greater), and that much of the deposit is within 20 feet of the surface. The maps included in this report can be used for land-use planning. Uses include location of favorable sites for specific uses such as landfills, utility corridors, heavy construction, etc; location of problem areas for specific land uses; identification of possible problems for specific areas; design and construction cost estimates; and prospecting for exploitable clay deposits. It Is suggested that, for effective planning, these maps be used together or in conjunction with other maps such as maps showing surface materials, depth to bedrock, depth to water table, and flood prone areas.

Rock Magnetic Fields Shield the Surface of Mars from Harmful Radiation

NASA Astrophysics Data System (ADS)

Alves, E. I.; Baptista, A. R.

2004-03-01

We intend to show that there is a negative correlation between areas of magnetic anomalies and areas of energetic particles bombardment on the surface of Mars, by comparing MGS MAG-ER and Mars Odyssey MARIE maps. Terra Sirenum is the most shielded area.

Terra and Aqua satellites track tiger mosquito invasion: modelling the potential distribution of Aedes albopictus in north-eastern Italy

PubMed Central

2011-01-01

Background The continuing spread of the Asian tiger mosquito Aedes albopictus in Europe is of increasing public health concern due to the potential risk of new outbreaks of exotic vector-borne diseases that this species can transmit as competent vector. We predicted the most favorable areas for a short term invasion of Ae. albopictus in north-eastern Italy using reconstructed daily satellite data time series (MODIS Land Surface Temperature maps, LST). We reconstructed more than 11,000 daily MODIS LST maps for the period 2001-09 (i.e. performed spatial and temporal gap-filling) in an Open Source GIS framework. We aggregated these LST maps over time and identified the potential distribution areas of Ae. albopictus by adapting published temperature threshold values using three variables as predictors (0°C for mean January temperatures, 11°C for annual mean temperatures and 1350 growing degree days filtered for areas with autumnal mean temperatures > 11°C). The resulting maps were integrated into the final potential distribution map and this was compared with the known current distribution of Ae. albopictus in north-eastern Italy. Results LST maps show the microclimatic characteristics peculiar to complex terrains, which would not be visible in maps commonly derived from interpolated meteorological station data. The patterns of the three indicator variables partially differ from each other, while winter temperature is the determining limiting factor for the distribution of Ae. albopictus. All three variables show a similar spatial pattern with some local differences, in particular in the northern part of the study area (upper Adige valley). Conclusions Reconstructed daily land surface temperature data from satellites can be used to predict areas of short term invasion of the tiger mosquito with sufficient accuracy (200 m pixel resolution size). Furthermore, they may be applied to other species of arthropod of medical interest for which temperature is a relevant limiting factor. The results indicate that, during the next few years, the tiger mosquito will probably spread toward northern latitudes and higher altitudes in north-eastern Italy, which will considerably expand the range of the current distribution of this species. PMID:21812983

Alaska: Glaciers of Kenai Fjords National Park and Katmai National Park and Preserve

NASA Technical Reports Server (NTRS)

Giffens, Bruce A.; Hall, Dorothy K.; Chien, Janet Y. L.

2014-01-01

There are hundreds of glaciers in Kenai Fjords National Park (KEFJ) and Katmai National Park and Preserve (KATM) covering over 2,276 sq km of park land (ca. 2000). There are two primary glacierized areas in KEFJ (the Harding Icefield and the Grewingk-Yalik Glacier Complex) and three primary glacierized areas in KATM (the Mt. Douglas area, the Kukak Volcano to Mt. Katmai area, and the Mt. Martin area). Most glaciers in these parks terminate on land, though a few terminate in lakes. Only KEFJ has tidewater glaciers, which terminate in the ocean. Glacier mapping and analysis of the change in glacier extent has been accomplished on a decadal scale using satellite imagery, primarily Landsat data from the 1970s, 1980s, and from2000. Landsat Multispectral Scanner (MSS),Thematic Mapper (TM), and Enhanced Thematic Mapper Plus (ETM) imagery was used to map glacier extent on a park-wide basis. Classification of glacier ice using image-processing software, along with extensive manual editing, was employed to create Geographic Information System (GIS)outlines of the glacier extent for each park. Many glaciers that originate in KEFJ but terminate outside the park boundaries were also mapped. Results of the analysis show that there has been a reduction in the amount of glacier ice cover in the two parks over the study period. Our measurements show a reduction of approximately 21 sq km, or 1.5(from 1986 to 2000), and 76 sq km, or 7.7 (from19861987 to 2000), in KEFJ and KATM, respectively. This work represents the first comprehensive study of glaciers of KATM. Issues that complicate the mapping of glacier extent include debris cover(moraine and volcanic ash), shadows, clouds, fresh snow, lingering snow from the previous season, and differences in spatial resolution between the MSS,TM, or ETM sensors. Similar glacier mapping efforts in western Canada estimate mapping errors of 34. Measurements were also collected from a suite of glaciers in KEFJ and KATM detailing terminus positions and rates of recession using datasets including 15 min USGS quadrangle maps(19501951), Landsat imagery (19861987, 2000,2006), and 2005 IKONOS imagery (KEFJ only).

Alaska: Glaciers of Kenai Fjords National Park and Katmai and Lake Clark National Parks and Preserve

NASA Technical Reports Server (NTRS)

Giffen, bruce A.; Hall, Dorothy K.; Chien, Janet Y. L.

2011-01-01

There are hundreds of glaciers in Kenai Fjords National Park (KEFJ) and Katmai National Park and Preserve (KATM) covering over 2276 sq km of park land (circa 2000). There are two primary glacierized areas in KEFJ -- the Harding Icefield and the Grewingk-Yalik Glacier Complex, and three primary glacierized areas in KATM - the Mt. Douglas area, the Kukak Volcano to Mt. Katmai area and the Mt. Martin area. Most glaciers in these parks terminate on land, though a few terminate in lakes. Only KEFJ has tidewater glaciers, which terminate in the ocean. Glacier mapping and analysis of the change in glacier extent has been accomplished on a decadal scale using satellite imagery, primarily Landsat data from the 1970s, 1980s, and from 2000. Landsat Multispectral Scanner (MSS), Thematic Mapper (TM) and Enhanced Thematic Mapper Plus (ETM+) imagery was used to map glacier extent on a park-wide basis. Classification of glacier ice using image processing software, along with extensive manual editing, was employed to create Geographic Information System (GIS) outlines of the glacier extent for each park. Many glaciers that originate in KEFJ but terminate outside the park boundaries were also mapped. Results of the analysis show that there has been a reduction in the amount of glacier ice cover in the two parks over the study period. Our measurements show a reduction of approximately 21 sq km, or -1.5% (from 1986 to 2000), and 76 sq km, or -7.7% (from 1986/87 to 2000), in KEFJ and KATM, respectively. This work represents the first comprehensive study of glaciers of KATM. Issues that complicate the mapping of glacier extent include: debris-cover (moraine and volcanic ash), shadows, clouds, fresh snow, lingering snow from the previous season, and differences in spatial resolution between the MSS and TM or ETM+ sensors. Similar glacier mapping efforts in western Canada estimate mapping errors of 3-4%. Measurements were also collected from a suite of glaciers in KEFJ and KATM detailing terminus positions and rates of recession using datasets including the 15-minute USGS quadrangle maps (1950/1951), Landsat imagery (1986/1987, 2000, 2006) and 2005 Ikonos imagery (KEFJ only).

A promising tool for subsurface permafrost mapping-An application of airborne geophysics from the Yukon River Basin, Alaska

USGS Publications Warehouse

Abraham, Jared E.

2011-01-01

In the area of Fort Yukon, the AEM survey shows elevated resistivities extending to depth, likely indicative of thick permafrost. This depth corresponds well to observations from a borehole drilled in the area in the late 1990s, which detected permafrost to a depth of about 100 meters (Clark and others, 2009). In contrast to the area of Fort Yukon, the Yukon River and its floodplain are not associated with deep resistive sediments, suggesting a lack of deep permafrost, at least within the depth range of the AEM mapping (fig. 3).

Thermal structure of Sikhote Alin and adjacent areas based on spectral analysis of the anomalous magnetic field

NASA Astrophysics Data System (ADS)

Didenko, A. N.; Nosyrev, M. Yu.; Shevchenko, B. F.; Gilmanova, G. Z.

2017-11-01

The depth of the base of the magnetoactive layer and the geothermal gradient in the Sikhote Alin crust are estimated based on a method determining the Curie depth point of magnetoactive masses by using spectral analysis of the anomalous magnetic field. A detailed map of the geothermal gradient is constructed for the first time for the Sikhote Alin and adjacent areas of the Central Asian belt. Analysis of this map shows that the zones with a higher geothermal gradient geographically fit the areas with a higher level of seismicity.

Islands of biogeodiversity in arid lands on a polygons map study: Detecting scale invariance patterns from natural resources maps.

PubMed

Ibáñez, J J; Pérez-Gómez, R; Brevik, Eric C; Cerdà, A

2016-12-15

Many maps (geology, hydrology, soil, vegetation, etc.) are created to inventory natural resources. Each of these resources is mapped using a unique set of criteria, including scales and taxonomies. Past research indicates that comparing results of related maps (e.g., soil and geology maps) may aid in identifying mapping deficiencies. Therefore, this study was undertaken in Almeria Province, Spain to (i) compare the underlying map structures of soil and vegetation maps and (ii) investigate if a vegetation map can provide useful soil information that was not shown on a soil map. Soil and vegetation maps were imported into ArcGIS 10.1 for spatial analysis, and results then exported to Microsoft Excel worksheets for statistical analyses to evaluate fits to linear and power law regression models. Vegetative units were grouped according to the driving forces that determined their presence or absence: (i) climatophilous (ii) lithologic-climate; and (iii) edaphophylous. The rank abundance plots for both the soil and vegetation maps conformed to Willis or Hollow Curves, meaning the underlying structures of both maps were the same. Edaphophylous map units, which represent 58.5% of the vegetation units in the study area, did not show a good correlation with the soil map. Further investigation revealed that 87% of the edaphohygrophilous units were found in ramblas, ephemeral riverbeds that are not typically classified and mapped as soils in modern systems, even though they meet the definition of soil given by the most commonly used and most modern soil taxonomic systems. Furthermore, these edaphophylous map units tend to be islands of biodiversity that are threatened by anthropogenic activity in the region. Therefore, this study revealed areas that need to be revisited and studied pedologically. The vegetation mapped in these areas and the soils that support it are key components of the earth's critical zone that must be studied, understood, and preserved. Copyright © 2016 Elsevier B.V. All rights reserved.

NASA Damage Map Aids Northern California Wildfire Response

NASA Image and Video Library

2017-10-18

The Advanced Rapid Imaging and Analysis (ARIA) team at NASA's Jet Propulsion Laboratory in Pasadena, California, and Caltech, also in Pasadena, created this Damage Proxy Map depicting areas in Northern California that are likely damaged (shown by red and yellow pixels) as a result of the region's current outbreak of wildfires. The map is derived from synthetic aperture radar (SAR) images from the Copernicus Sentinel-1 satellites, operated by the European Space Agency (ESA). The images were taken before (Sep. 27, 2017, 7 p.m. PDT) and after (Oct. 9, 2017, 7 p.m. PDT) the onset of the fires. The map has been provided to various agencies to aid in the wildfire response. The map covers the area within the large red polygon, and measures 155 by 106 miles (250 by 170 kilometers). The illustrative figure from the map depicted in the inset shows damage in the city of Santa Rosa. Each pixel in the Damage Proxy Map measures about 98 feet (30 meters) across. The color variation from yellow to red indicates increasingly more significant ground surface change. Preliminary validation was done by comparing to optical satellite imagery from DigitalGlobe. This Damage Proxy Map should be used as guidance to identify damaged areas, and may be less reliable over vegetated areas. Sentinel-1 data were accessed through the Copernicus Open Access Hub. The image contains modified Copernicus Sentinel data (2017), processed by ESA and analyzed by the NASA-JPL/Caltech ARIA team. This research was carried out at JPL under a contract with NASA. https://photojournal.jpl.nasa.gov/catalog/PIA22048

Earthquake Hazard Class Mapping by Parcel in Las Vegas Valley

NASA Astrophysics Data System (ADS)

Pancha, A.; Pullammanappallil, S.; Louie, J. N.; Hellmer, W. K.

2011-12-01

Clark County, Nevada completed the very first effort in the United States to map earthquake hazard class systematically through an entire urban area. The map is used in development and disaster response planning, in addition to its direct use for building code implementation and enforcement. The County contracted with the Nevada System of Higher Education to classify about 500 square miles including urban Las Vegas Valley, and exurban areas considered for future development. The Parcel Map includes over 10,000 surface-wave array measurements accomplished over three years using Optim's SeisOpt° ReMi measurement and processing techniques adapted for large scale data. These array measurements classify individual parcels on the NEHRP hazard scale. Parallel "blind" tests were conducted at 93 randomly selected sites. The rms difference between the Vs30 values yielded by the blind data and analyses and the Parcel Map analyses is 4.92%. Only six of the blind-test sites showed a difference with a magnitude greater than 10%. We describe a "C+" Class for sites with Class B average velocities but soft surface soil. The measured Parcel Map shows a clearly definable C+ to C boundary on the west side of the Valley. The C to D boundary is much more complex. Using the parcel map in computing shaking in the Valley for scenario earthquakes is crucial for obtaining realistic predictions of ground motions.

Global climate change and local land subsidence exacerbate inundation risk to the San Francisco Bay Area

PubMed Central

Shirzaei, Manoochehr; Bürgmann, Roland

2018-01-01

The current global projections of future sea level rise are the basis for developing inundation hazard maps. However, contributions from spatially variable coastal subsidence have generally not been considered in these projections. We use synthetic aperture radar interferometric measurements and global navigation satellite system data to show subsidence rates of less than 2 mm/year along most of the coastal areas along San Francisco Bay. However, rates exceed 10 mm/year in some areas underlain by compacting artificial landfill and Holocene mud deposits. The maps estimating 100-year inundation hazards solely based on the projection of sea level rise from various emission scenarios underestimate the area at risk of flooding by 3.7 to 90.9%, compared with revised maps that account for the contribution of local land subsidence. Given ongoing land subsidence, we project that an area of 125 to 429 km2 will be vulnerable to inundation, as opposed to 51 to 413 km2 considering sea level rise alone. PMID:29536042

Map showing structure of the Mississippi Valley Graben in the vicinity of New Madrid, Missouri

USGS Publications Warehouse

Wheeler, Russell L.; Rhea, Susan; Dart, Richard L.

1994-01-01

This is one of a series of five seismotectonic maps of the seismically active New Madrid area in southeast Missouri and adjacent parts of Arkansas, Kentucky, and Tennessee (table 1). We cannot legibly show all the seismotectonic data on a single map, therefore each of the five maps in this series groups a different type of related information. Rhea and others (1994) summarized the background and purpose of the seismotectonic map folio. The different types of data shown on this map are described in table 2. Except for a few exposed faults, all structures shown on the map are in Paleozoic sedimentary rocks of the midcontinent or underlying metamorphic and igneous basement rocks of presumed Precambrian age (Dart, 1992; Muehlberger, 1992). Edge of Mississippi Embayment, as shown on the map, marks the contact between gently dipping, exposed Paleozoic rocks to the northwest (Anderson and others, 1979) and unconformably overlying, flat or gently dipping Mesozoic and Cenozoic strata of the embayment to the southeast.

Assessment of an air pollution monitoring network to generate urban air pollution maps using Shannon information index, fuzzy overlay, and Dempster-Shafer theory, A case study: Tehran, Iran

NASA Astrophysics Data System (ADS)

Pahlavani, Parham; Sheikhian, Hossein; Bigdeli, Behnaz

2017-10-01

Air pollution assessment is an imperative part of megacities planning and control. Hence, a new comprehensive approach for air pollution monitoring and assessment was introduced in this research. It comprises of three main sections: optimizing the existing air pollutant monitoring network, locating new stations to complete the coverage of the existing network, and finally, generating an air pollution map. In the first section, Shannon information index was used to find less informative stations to be candidate for removal. Then, a methodology was proposed to determine the areas which are not sufficiently covered by the current network. These areas are candidates for establishing new monitoring stations. The current air pollution monitoring network of Tehran was used as a case study, where the air pollution issue has been worsened due to the huge population, considerable commuters' absorption and topographic barriers. In this regard, O3, NO, NO2, NOx, CO, PM10, and PM2.5 were considered as the main pollutants of Tehran. Optimization step concluded that all the 16 active monitoring stations should be preserved. Analysis showed that about 35% of the Tehran's area is not properly covered by monitoring stations and about 30% of the area needs additional stations. The winter period in Tehran always faces the most severe air pollution in the year. Hence, to produce the air pollution map of Tehran, three-month of winter measurements of the mentioned pollutants, repeated for five years in the same period, were selected and extended to the entire area using the kriging method. Experts specified the contribution of each pollutant in overall air pollution. Experts' rankings aggregated by a fuzzy-overlay process. Resulted maps characterized the study area with crucial air pollution situation. According to the maps, more than 45% of the city area faced high pollution in the study period, while only less than 10% of the area showed low pollution. This situation confirms the need for effective plans to mitigate the severity of the problem. In addition, an effort made to investigate the rationality of the acquired air pollution map respect to the urban, cultural, and environmental characteristics of Tehran, which also confirmed the results.

Use of remote sensing and GIS in mapping the environmental sensitivity areas for desertification of Egyptian territory

NASA Astrophysics Data System (ADS)

Gad, A.; Lotfy, I.

2008-06-01

Desertification is defined in the first art of the convention to combat desertification as "land degradation in arid, semiarid and dry sub-humid areas resulting from climatic variations and human activities". Its consequence include a set of important processes which are active in arid and semi arid environment, where water is the main limiting factor of land use performance in such ecosystem . Desertification indicators or the groups of associated indicators should be focused on a single process. They should be based on available reliable information sources, including remotely sensed images, topographic data (maps or DEM'S), climate, soils and geological data. The current work aims to map the Environmental Sensitivity Areas (ESA's) to desertification in whole territory of Egypt at a scale of 1:1 000 000. ETM satellite images, geologic and soil maps were used as main sources for calculating the index of Environmental Sensitivity Areas (ESAI) for desertification. The algorism is adopted from MEDALLUS methodology as follows; ESAI = (SQI * CQI * VQI)1/3 Where SQI is the soil quality index, CQI is the climate quality index and VQI is the vegetation quality index. The SQI is based on rating the parent material, slope, soil texture, and soil depth. The VQI is computed on bases of rating three categories (i.e. erosion protection, drought resistance and plant cover). The CQI is based on the aridity index, derived from values of annual rainfall and potential evapotranspiration. Arc-GIS 9 software was used for the computation and sensitivity maps production. The results show that the soil of the Nile Valley are characterized by a moderate SQI, however the those in the interference zone are low soil quality indexed. The dense vegetation of the valley has raised its VQI to be good, however coastal areas are average and interference zones are low. The maps of ESA's for desertification show that 86.1% of Egyptian territory is classified as very sensitive areas, while 4.3% as Moderately sensitive, and 9.6% as sensitive. It can be concluded that implementing the maps of sensitivity to desertification is rather useful in the arid and semi arid areas as they give more likely quantitative trend for frequency of sensitive areas. The integration of different factors contributing to desertification sensitivity may lead to plan a successful combating. The usage of space data and GIS proved to be suitable tools to rely estimation and to fulfill the needed large computational requirements. They are also useful in visualizing the sensitivity situation of different desertification parameters.

Geologic map of the La Mesita Negra SE Quadrangle, Bernalillo County, New Mexico

USGS Publications Warehouse

Shroba, Ralph R.; Thompson, Ren A.; Schmidt, Dwight L.; Personius, Stephen F.; Maldonado, Florian; Brandt, Theodore R.

2003-01-01

Geologic mapping, in support of the USGS Middle Rio Grande Basin Geologic Mapping Project, shows the spatial distribution of artificial-fill, alluvial, colluvial, and eolian deposits, lava flows and related sediments of the Albuquerque volcanoes, and upper Santa Fe Group sediments. These deposits are on, beneath, and along the West Mesa (Llano de Albuquerque) just west of Albuquerque, New Mexico. Artificial fill deposits are mapped chiefly beneath and near segments of Interstate 40, in an inactive landfill (or dump) north of Interstate 40 near the eastern boundary of the map area, and in the active Cerro Colorado landfill near the southwestern corner of the map area. Alluvial deposits are mapped in stream channels, beneath treads of terraces, and on hill slopes. They include alluvium in stream channels and beneath treads of low terraces, terrace alluvium, sheetwash deposits, gravelly alluvium, and old alluvium and calcic soils of the Llano de Albuquerque. Alluvial and colluvial deposits are mapped on hill slopes. They include young alluvial-slope deposits, alluvium and colluvium, undivided, and old alluvial-slope deposits. Colluvial deposits are also mapped on hill slopes. They include colluvial deposits, undivided, as well as alluvial deposits, eolian sand, and calcic soils associated with fault scarps. Eolian deposits as well as eolian and alluvial deposits mantle gently slopping surfaces on the Llano de Albuquerque. They include active eolian sand, active and inactive eolian sand and sheetwash deposits, undivided, and inactive eolian sand and sheetwash deposits, undivided. Lava flows and related sediments of the Albuquerque volcanoes were mapped near the southeast corner of the map area. They include five young lava flows, two young cinder deposits, and old lava flows. Upper Santa Fe Group sediments are well exposed and mapped in the western part of the map area. They include a gravel unit, a pebbly sand unit, and a mud and sand unit. Undivided upper Santa Fe Group sediments were mapped in the eastern part of the map area. Sediments and lava flows in the map area record alluvial, eolian, colluvial, and volcanic processes of the past several million years. The surficial deposits (post-Santa Fe Group sediments) on the map are known or estimated to be at least 1 m thick; most deposits are poorly exposed. Thin (< 50 cm), discontinuous deposits of eolian sand and sheetwash (Qea, Qes, and Qsw) locally are present on gently sloping map units older than the alluvium in stream channels and low terraces (Qa). These thin eolian and sheetwash deposits are not mapped, but they are widespread on the gravel unit of the upper Santa Fe Group sediments (Tg) on the eastern flank of the Llano de Albuquerque, near the eastern boundary of the map area (quadrangle). Small deposits of artificial fill (af) less than about 25 m wide are not mapped. Fractional map symbols (for example, Qsw/Qby1) are used where sheetwash deposits mantle lava flows. These fractional units are not described here; instead refer to descriptions of individual units.

Groundwater vulnerability assessment for organic compounds: fuzzy multi-criteria approach for Mexico city.

PubMed

Mazari-Hiriart, Marisa; Cruz-Bello, Gustavo; Bojórquez-Tapia, Luis A; Juárez-Marusich, Lourdes; Alcantar-López, Georgina; Marín, Luis E; Soto-Galera, Ernesto

2006-03-01

This study was based on a groundwater vulnerability assessment approach implemented for the Mexico City Metropolitan Area (MCMA). The approach is based on a fuzzy multi-criteria procedure integrated in a geographic information system. The approach combined the potential contaminant sources with the permeability of geological materials. Initially, contaminant sources were ranked by experts through the Analytic Hierarchy Process. An aggregated contaminant sources map layer was obtained through the simple additive weighting method, using a scalar multiplication of criteria weights and binary maps showing the location of each source. A permeability map layer was obtained through the reclassification of a geology map using the respective hydraulic conductivity values, followed by a linear normalization of these values against a compatible scale. A fuzzy logic procedure was then applied to transform and combine the two map layers, resulting in a groundwater vulnerability map layer of five classes: very low, low, moderate, high, and very high. Results provided a more coherent assessment of the policy-making priorities considered when discussing the vulnerability of groundwater to organic compounds. The very high and high vulnerability areas covered a relatively small area (71 km(2) or 1.5% of the total study area), allowing the identification of the more critical locations. The advantage of a fuzzy logic procedure is that it enables the best possible use to be made of the information available regarding groundwater vulnerability in the MCMA.

Testing an innovative framework for flood forecasting, monitoring and mapping in Europe

NASA Astrophysics Data System (ADS)

Dottori, Francesco; Kalas, Milan; Lorini, Valerio; Wania, Annett; Pappenberger, Florian; Salamon, Peter; Ramos, Maria Helena; Cloke, Hannah; Castillo, Carlos

2017-04-01

Between May and June 2016, France was hit by severe floods, particularly in the Loire and Seine river basins. In this work, we use this case study to test an innovative framework for flood forecasting, mapping and monitoring. More in detail, the system integrates in real-time two components of the Copernicus Emergency mapping services, namely the European Flood Awareness System and the satellite-based Rapid Mapping, with new procedures for rapid risk assessment and social media and news monitoring. We explore in detail the performance of each component of the system, demonstrating the improvements in respect to stand-alone flood forecasting and monitoring systems. We show how the performances of the forecasting component can be refined using the real-time feedback from social media monitoring to identify which areas were flooded, to evaluate the flood intensity, and therefore to correct impact estimations. Moreover, we show how the integration with impact forecast and social media monitoring can improve the timeliness and efficiency of satellite based emergency mapping, and reduce the chances of missing areas where flooding is already happening. These results illustrate how the new integrated approach leads to a better and earlier decision making and a timely evaluation of impacts.

GIS-aided low flow mapping

NASA Astrophysics Data System (ADS)

Saghafian, B.; Mohammadi, A.

2003-04-01

Most studies involving water resources allocation, water quality, hydropower generation, and allowable water withdrawal and transfer require estimation of low flows. Normally, frequency analysis on at-station D-day low flow data is performed to derive various T-yr return period values. However, this analysis is restricted to the location of hydrometric stations where the flow discharge is measured. Regional analysis is therefore conducted to relate the at-station low flow quantiles to watershed characteristics. This enables the transposition of low flow quantiles to ungauged sites. Nevertheless, a procedure to map the regional regression relations for the entire stream network, within the bounds of the relations, is particularly helpful when one studies and weighs alternative sites for certain water resources project. In this study, we used a GIS-aided procedure for low flow mapping in Gilan province, part of northern region in Iran. Gilan enjoys a humid climate with an average of 1100 mm annual precipitation. Although rich in water resources, the highly populated area is quite dependent on minimum amount of water to sustain the vast rice farming and to maintain required flow discharge for quality purposes. To carry out the low flow analysis, a total of 36 hydrometric stations with sufficient and reliable discharge data were identified in the region. The average area of the watersheds was 250 sq. km. Log Pearson type 3 was found the best distribution for flow durations over 60 days, while log normal fitted well the shorter duration series. Low flows with return periods of 2, 5, 10, 25, 50, and 100 year were then computed. Cluster analysis identified two homogeneous areas. Although various watershed parameters were examined in factor analysis, the results showed watershed area, length of the main stream, and annual precipitation were the most effective low flow parameters. The regression equations were then mapped with the aid of GIS based on flow accumulation maps and the corresponding spatially averaged values of other parameters over the upslope area of all stream pixels exceeding a certain threshold area. Such map clearly shows the spatial variation of low flow quantiles along the stream network and enables the study of low flow profiles along any stream.

Potentiometric maps of the Sparta Sand, northern Louisiana and southern Arkansas, 1900, 1965, 1975, and 1980

USGS Publications Warehouse

Ryals, G.N.

1980-01-01

The potentiometric surface of the Sparta Sand in northern Louisiana is shown by contours on four maps. Maps for 1900, 1965 , and spring 1975 are generalized, small-scale maps from previously published reports. The spring 1980 map (1:500,000) is based on measurements in 144 wells and includes the southern tier of counties in southern Arkansas. The map shows regional effects of pumping from the Sparta Sand and effects of local pumping centers at Magnolia and El Dorado, Ark., and at Minden, Ruston, Jonesboro-Hodge, Winnfield, Bastrop, and in the Monroe area of Louisiana. (USGS)

Seabed maps showing topography, ruggedness, backscatter intensity, sediment mobility, and the distribution of geologic substrates in Quadrangle 6 of the Stellwagen Bank National Marine Sanctuary Region offshore of Boston, Massachusetts

USGS Publications Warehouse

Valentine, Page C.; Gallea, Leslie B.

2015-11-10

The U.S. Geological Survey (USGS), in cooperation with the National Oceanic and Atmospheric Administration's National Marine Sanctuary Program, has conducted seabed mapping and related research in the Stellwagen Bank National Marine Sanctuary (SBNMS) region since 1993. The area is approximately 3,700 square kilometers (km2) and is subdivided into 18 quadrangles. Seven maps, at a scale of 1:25,000, of quadrangle 6 (211 km2) depict seabed topography, backscatter, ruggedness, geology, substrate mobility, mud content, and areas dominated by fine-grained or coarse-grained sand. Interpretations of bathymetric and seabed backscatter imagery, photographs, video, and grain-size analyses were used to create the geology-based maps. In all, data from 420 stations were analyzed, including sediment samples from 325 locations. The seabed geology map shows the distribution of 10 substrate types ranging from boulder ridges to immobile, muddy sand to mobile, rippled sand. Mapped substrate types are defined on the basis of sediment grain-size composition, surface morphology, sediment layering, the mobility or immobility of substrate surfaces, and water depth range. This map series is intended to portray the major geological elements (substrates, topographic features, processes) of environments within quadrangle 6. Additionally, these maps will be the basis for the study of the ecological requirements of invertebrate and vertebrate species that utilize these substrates and guide seabed management in the region.

Tectonic map of the Circum-Pacific region, Pacific basin sheet

USGS Publications Warehouse

Scheibner, E.; Moore, G.W.; Drummond, K.J.; Dalziel, Corvalan Q.J.; Moritani, T.; Teraoka, Y.; Sato, T.; Craddock, C.

2013-01-01

Circum-Pacific Map Project: The Circum-Pacific Map Project was a cooperative international effort designed to show the relationship of known energy and mineral resources to the major geologic features of the Pacific basin and surrounding continental areas. Available geologic, mineral, and energy-resource data are being complemented by new, project-developed data sets such as magnetic lineations, seafloor mineral deposits, and seafloor sediment. Earth scientists representing some 180 organizations from more than 40 Pacific-region countries are involved in this work. Six overlapping equal-area regional maps at a scale of 1:10,000,000 form the cartographic base for the project: the four Circum-Pacific Quadrants (Northwest, Southwest, Southeast, and Northeast), and the Antarctic and Arctic Sheets. There is also a Pacific Basin Sheet at a scale of 1:17,000,000. The Base Map Series and the Geographic Series (published from 1977 to 1990), the Plate-Tectonic Series (published in 1981 and 1982), the Geodynamic Series (published in 1984 and 1985), and the Geologic Series (published from 1984 to 1989) all include six map sheets. Other thematic map series in preparation include Mineral-Resources, Energy-Resources and Tectonic Maps. Altogether, more than 50 map sheets are planned. The maps were prepared cooperatively by the Circum-Pacific Council for Energy and Mineral Resources and the U.S. Geological Survey and are available from the Branch of Distribution, U. S. Geological Survey, Box 25286, Federal Center, Denver, Colorado 80225, U.S.A. The Circum-Pacific Map Project is organized under six panels of geoscientists representing national earth-science organizations, universities, and natural-resource companies. The six panels correspond to the basic map areas. Current panel chairmen are Tomoyuki Moritani (Northwest Quadrant), R. Wally Johnson (Southwest Quadrant), Ian W.D. Dalziel (Antarctic Region), vacant. (Southeast Quadrant), Kenneth J. Drummond (Northeast Quadrant), and George W. Moore (Arctic Region). Project coordination and final cartography was being carried out through the cooperation of the Office of the Chief Geologist of the U.S. Geological Survey, under the direction of General Chairman, George Gryc of Menlo Park, California. Project headquarters were located at 345 Middlefield Road, MS 952, Menlo Park, California 94025, U.S.A. The framework for the Circum-Pacific Map Project was developed in 1973 by a specially convened group of 12 North American geoscientists meeting in California. The project was officially launched at the First Circum-Pacific Conference on Energy and Mineral Resources, which met in Honolulu, Hawaii, in August 1974. Sponsors of the conference were the AAPG, Pacific Science Association (PSA), and the Coordinating Committee for Offshore Prospecting for Mineral Resources in Offshore Asian Areas (CCOP). The Circum-Pacific Map Project operates as an activity of the Circum-Pacific Council for Energy and Mineral Resources, a nonprofit organization that promotes cooperation among Circum-Pacific countries in the study of energy and mineral resources of the Pacific basin. Founded by Michel T. Halbouty in 1972, the Council also sponsors conferences, topical symposia, workshops and the Earth Science Series books. Tectonic Map Series: The tectonic maps distinguish areas of oceanic and continental crust. Symbols in red mark active plate boundaries, and colored patterns show tectonic units (volcanic or magmatic arcs, arc-trench gaps, and interarc basins) associated with active plate margins. Well-documented inactive plate boundaries are shown by symbols in black. The tectonic development of oceanic crust is shown by episodes of seafloor spreading. These correlate with the rift and drift sequences at passive continental margins and episodes of tectonic activity at active plate margins. The recognized episodes of seafloor spreading seem to reflect major changes in plate kinematics. Oceanic plateaus and other prominences of greater than normal oceanic crustal thickness such as hotspot traces are also shown. Colored areas on the continents show the ages of deformation and metamorphism of basement rocks and the emplacement of igneous rocks. Transitional tectonic (molassic) and reactivation basins are shown by a colored boundary, and if they are deformed, a colored horizontal line pattern indicates the age of deformation. Colored bands along basin boundaries indicate age of inception, and isopachs indicate thickness of platform strata on continental crust and cover on oceanic crust. Colored patterns at separated continental margins show the age of inception of rift and drift (breakup) sequences. Symbols mark folds and faults, and special symbols show volcanoes and other structural features. Affiliations are as of compilation of the data. This map was created in quadrants and then compiled together. They are the Northwest land, Northwest Marine (different compilers), Northeast, Southwest and Southeast, and parts in plate-boundary sections.

Relation between thallium-201/iodine 123-BMIPP subtraction and fluorine 18 deoxyglucose polar maps in patients with hypertrophic cardiomyopathy.

PubMed

Ito, Y; Hasegawa, S; Yamaguchi, H; Yoshioka, J; Uehara, T; Nishimura, T

2000-01-01

Clinical studies have shown discrepancies in the distribution of thallium-201 and iodine 123-beta-methyl-iodophenylpentadecanoic acid (BMIPP) in patients with hypertrophic cardiomyopathy (HCM). Myocardial uptake of fluorine 18 deoxyglucose (FDG) is increased in the hypertrophic area in HCM. We examined whether the distribution of a Tl-201/BMIPP subtraction polar map correlates with that of an FDG polar map. We normalized to maximum count each Tl-201 and BMIPP bull's-eye polar map of 6 volunteers and obtained a standard Tl-201/BMIPP subtraction polar map by subtracting a normalized BMIPP bull's-eye polar map from a normalized Tl-201 bull's-eye polar map. The Tl-201/BMIPP subtraction polar map was then applied to 8 patients with HCM (mean age 65+/-12 years) to evaluate the discrepancy between Tl-201 and BMIPP distribution. We compared the Tl-201/BMIPP subtraction polar map with an FDG polar map. In patients with HCM, the Tl-201/BMIPP subtraction polar map showed a focal uptake pattern in the hypertrophic area similar to that of the FDG polar map. By quantitative analysis, the severity score of the Tl-201/BMIPP subtraction polar map was significantly correlated with the percent dose uptake of the FDG polar map. These results suggest that this new quantitative method may be an alternative to FDG positron emission tomography for the routine evaluation of HCM.

Potentiometric Surface of the Patuxent Aquifer in Southern Maryland, September 2009

USGS Publications Warehouse

Curtin, Stephen E.; Andreasen, David C.; Staley, Andrew W.

2010-01-01

This report presents a map showing the potentiometric surface of the Patuxent aquifer in the Patuxent Formation of Early Cretaceous age in Southern Maryland during September 2009. The map is based on water-level measurements in 42 wells. The highest measured water level was 169 feet above sea level in the outcrop area of the aquifer in northern Prince George's County. From this area, the potentiometric surface declined south towards well fields at Glen Burnie, Bryans Road, the Morgantown power plant, and the Chalk Point power plant. The measured groundwater levels were 78 feet below sea level at Glen Burnie, 56 feet below sea level at Bryans Road, 29 feet below sea level at the Morgantown power plant, and 28 feet below sea level at the Chalk Point power plant. The map also shows well yield in gallons per day for 2008 at wells or well fields.

Geologic Mapping of Ascraeus Mons, Mars

NASA Technical Reports Server (NTRS)

Mohr, K. J.; Williams, D. A.; Garry, W. B.

2016-01-01

Ascraeus Mons (AM) is the northeastern most large shield volcano residing in the Tharsis province on Mars. We are funded by NASA's Mars Data Analysis Program to complete a digital geologic map based on the mapping style. Previous mapping of a limited area of these volcanoes using HRSC images (13-25 m/pixel) revealed a diverse distribution of volcanic landforms within the calderas, along the flanks, rift aprons, and surrounding plains. The general scientific objectives for which this mapping is based is to show the different lava flow morphologies across AM to better understand the evolution and geologic history.

DeepSurveyCam--A Deep Ocean Optical Mapping System.

PubMed

Kwasnitschka, Tom; Köser, Kevin; Sticklus, Jan; Rothenbeck, Marcel; Weiß, Tim; Wenzlaff, Emanuel; Schoening, Timm; Triebe, Lars; Steinführer, Anja; Devey, Colin; Greinert, Jens

2016-01-28

Underwater photogrammetry and in particular systematic visual surveys of the deep sea are by far less developed than similar techniques on land or in space. The main challenges are the rough conditions with extremely high pressure, the accessibility of target areas (container and ship deployment of robust sensors, then diving for hours to the ocean floor), and the limitations of localization technologies (no GPS). The absence of natural light complicates energy budget considerations for deep diving flash-equipped drones. Refraction effects influence geometric image formation considerations with respect to field of view and focus, while attenuation and scattering degrade the radiometric image quality and limit the effective visibility. As an improvement on the stated issues, we present an AUV-based optical system intended for autonomous visual mapping of large areas of the seafloor (square kilometers) in up to 6000 m water depth. We compare it to existing systems and discuss tradeoffs such as resolution vs. mapped area and show results from a recent deployment with 90,000 mapped square meters of deep ocean floor.

Manifestation of a neuro-fuzzy model to produce landslide susceptibility map using remote sensing data derived parameters

NASA Astrophysics Data System (ADS)

Pradhan, Biswajeet; Lee, Saro; Buchroithner, Manfred

Landslides are the most common natural hazards in Malaysia. Preparation of landslide suscep-tibility maps is important for engineering geologists and geomorphologists. However, due to complex nature of landslides, producing a reliable susceptibility map is not easy. In this study, a new attempt is tried to produce landslide susceptibility map of a part of Cameron Valley of Malaysia. This paper develops an adaptive neuro-fuzzy inference system (ANFIS) based on a geographic information system (GIS) environment for landslide susceptibility mapping. To ob-tain the neuro-fuzzy relations for producing the landslide susceptibility map, landslide locations were identified from interpretation of aerial photographs and high resolution satellite images, field surveys and historical inventory reports. Landslide conditioning factors such as slope, plan curvature, distance to drainage lines, soil texture, lithology, and distance to lineament were extracted from topographic, soil, and lineament maps. Landslide susceptible areas were analyzed by the ANFIS model and mapped using the conditioning factors. Furthermore, we applied various membership functions (MFs) and fuzzy relations to produce landslide suscep-tibility maps. The prediction performance of the susceptibility map is checked by considering actual landslides in the study area. Results show that, triangular, trapezoidal, and polynomial MFs were the best individual MFs for modelling landslide susceptibility maps (86

Geologic map and structure sections of the Clear Lake Volcanics, Northern California

USGS Publications Warehouse

Hearn, B.C.; Donnelly-Nolan, J. M.; Goff, F.E.

1995-01-01

The Clear Lake Volcanics are located in the California Coast Ranges about 150 km north of San Francisco. This Quaternary volcanic field has erupted intermittently since 2.1 million years ago. This volcanic field is considered a high-threat volcanic system (Ewert and others, 2005) The adjacent Geysers geothermal field, largest power-producing geothermal field in the world, is powered by the magmatic heat source for the volcanic field. This report consists of three sheets that include the geologic map, one table, two figures, three cross sections, description of map units, charts of standard and diagrammatic correlation of map units, and references. This map supersedes U.S. Geological Survey Open-File Report 76-751. Descriptions of map units are grouped by geographic area. Summaries of the evolution, chemistry, structure, and tectonic setting of the Clear Lake Volcanics are given in Hearn and others (1981) and Donnelly-Nolan and others (1981). The geology of parts of the area underlain by the Cache Formation is based on mapping by Rymer (1981); the geology of parts of the areas underlain by the Sonoma Volcanics, Franciscan assemblage, and Great Valley sequence is based on mapping by McLaughlin (1978). Volcanic compositional map units are basalt, basaltic andesite, andesite, dacite, rhyodacite, and rhyolite, based on SiO2 content. Included in this report are maps showing the distribution of volcanic rocks through time and a chart showing erupted volumes of different lava types through time. A table gives petrographic data for each map unit by mineral type, abundance, and size. Most ages are potassium-argon (K/Ar) ages determined for whole-rock samples and mineral separates by Donnelly-Nolan and others (1981), unless otherwise noted. A few ages are carbon-14 ages or were estimated from geologic relationships. Magnetic polarities are from Mankinen and others (1978; 1981) or were determined in the field by B.C. Hearn, Jr., using a portable fluxgate magnetometer. Thickness for most units is estimated from topographic relief except where drill-hole data were available.

Time-series studies of drainage pattern and morphological features along the Leitha river (Eastern Austria)

NASA Astrophysics Data System (ADS)

Zámolyi, A.; Draganits, E.; Doneus, M.; Fera, M.; Griebl, M.

2009-04-01

Geomorphologic mapping and drainage network analysis was conducted in the Southern Vienna Basin on the Leitha and Fischa rivers. The study area belongs to an active pull-apart basin between the Eastern Alps and the Carpathians that started to subside in Karpatian times (~ 17 Ma), but with still active faults, proven by fault scarps and earth quakes. The investigated rivers are important tributaries to the Danube river and run through a region that has been subject to settlement since Neoltihic times. Thus, interaction between land use, settlement pattern and river dynamics can be studied. Several datasets are integrated to perform a comprehensive overview of geomorphological, as well as river dynamic changes in the landscape. During an earlier stage of this investigation a map of paleochannel distribution including the location and shape of the paleochannels was extracted from color-infrared and RGB digital orthophotos. Based on this map the location, character and shape of palaeomeanders is studied on different georeferenced historic maps (Timár et al., 2006; Biszak et al., 2007) in order to derive a time-series study. The paleochannels extracted from the digital orthophotos show a good coincidence with the depicted rivers on the historic maps. This partly allows quite well constrained age estimates of the paleochannel sections. The investigated maps are the Walter maps, the First, Second and Third Military Survey of the Habsburg/Austro-Hungarian Empire. Mapping of the Walter maps was conducted 1754-56 (Ulbrich, 1952), the First, Second and Third Military Surveys were mapped in this area in the time-span of 1782-1785, 1819-1869, and 1872-1873, respectively (Kretschmer et al., 2004). This sequence of georeferenced historical maps allows to study only a very short time-span (1755 - 1873) compared to the geological time scale. However, the characteristics of river dynamics special for the study area can be derived and, considering certain assumptions, extrapolated to a wider time range. Within the observable time period the Leitha river preserved its meandering characteristics. Small shifts of the mean channel towards E or W can be detected. A disadvantage of the maps previous to the Third Military Survey is the lack of contour lines. On these maps, variation in terrain elevation was mapped „a la vue" and rather depicted as changes in slope of the terrain by applying hatchures showing a density increase with higher slope. This method provided a very plastic overview of changes in the terrain, but the reading of absolute or relative elevations is not possible. According to this, geomorphologic observations from these maps are constricted to the comparison of the horizontal position of elevated areas and the change of their outline. This study shows that historical maps provide an essential tool to investigate younger river dynamics and sensitively show the impact of anthropological modifications as well as active tectonics. Biszak, S., Timár, G., Molnár, G., Jankó, A. (2007): Digitized maps of the Habsburg Empire - The third military survey, Österreichisch-Ungarische Monarchie, 1869-1887, 1:75000. DVD-issue, Arcanum, Budapest. ISBN 978-963-73-7451-7 Kretschmer, I., Dörflinger, J., Wawrick, F. (2004): Österreichische Kartographie. Wiener Schiften zur Geographie und Kartographie - Band 15. Institut für Geographie und Regionalforschung der Universität Wien, Wien. Timár, G., Molnár, G., Székely, B., Biszak, S., Varga, J., Jankó, A. (2006): Digitized maps of the Habsburg Empire - The map sheets of the second military survey and their georeferenced version. Arcanum, Budapest, 59 p. ISBN 963-7374-33-7 Ulbrich K. (1952): Die Grenzkarte Ungarn-Niederösterreich von C. J. Walter (1754 - 56). Burgenländische Heimatblätter, 14, 108-121

Temporal and spatial mapping of red grouper Epinephelus morio sound production.

PubMed

Wall, C C; Simard, P; Lindemuth, M; Lembke, C; Naar, D F; Hu, C; Barnes, B B; Muller-Karger, F E; Mann, D A

2014-11-01

The goals of this project were to determine the daily, seasonal and spatial patterns of red grouper Epinephelus morio sound production on the West Florida Shelf (WFS) using passive acoustics. An 11 month time series of acoustic data from fixed recorders deployed at a known E. morio aggregation site showed that E. morio produce sounds throughout the day and during all months of the year. Increased calling (number of files containing E. morio sound) was correlated to sunrise and sunset, and peaked in late summer (July and August) and early winter (November and December). Due to the ubiquitous production of sound, large-scale spatial mapping across the WFS of E. morio sound production was feasible using recordings from shorter duration-fixed location recorders and autonomous underwater vehicles (AUVs). Epinephelus morio were primarily recorded in waters 15-93 m deep, with increased sound production detected in hard bottom areas and within the Steamboat Lumps Marine Protected Area (Steamboat Lumps). AUV tracks through Steamboat Lumps, an offshore marine reserve where E. morio hole excavations have been previously mapped, showed that hydrophone-integrated AUVs could accurately map the location of soniferous fish over spatial scales of <1 km. The results show that passive acoustics is an effective, non-invasive tool to map the distribution of this species over large spatial scales. © 2014 The Fisheries Society of the British Isles.

Groundwater favorability map using GIS multicriteria data analysis on crystalline terrain, São Paulo State, Brazil

NASA Astrophysics Data System (ADS)

Madrucci, Vanessa; Taioli, Fabio; de Araújo, Carlos César

2008-08-01

SummaryThis paper presents the groundwater favorability mapping on a fractured terrain in the eastern portion of São Paulo State, Brazil. Remote sensing, airborne geophysical data, photogeologic interpretation, geologic and geomorphologic maps and geographic information system (GIS) techniques have been used. The results of cross-tabulation between these maps and well yield data allowed groundwater prospective parameters in a fractured-bedrock aquifer. These prospective parameters are the base for the favorability analysis whose principle is based on the knowledge-driven method. The multicriteria analysis (weighted linear combination) was carried out to give a groundwater favorability map, because the prospective parameters have different weights of importance and different classes of each parameter. The groundwater favorability map was tested by cross-tabulation with new well yield data and spring occurrence. The wells with the highest values of productivity, as well as all the springs occurrence are situated in the excellent and good favorability mapped areas. It shows good coherence between the prospective parameters and the well yield and the importance of GIS techniques for definition of target areas for detail study and wells location.

Multipurpose bedrock surficial, and environmental geologic maps, New River valley, southwest Virginia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schultz, A.; Collins, T.

1994-03-01

Multipurpose bedrock, surficial, and environmental geologic maps have recently been completed for portions of the Valley and Ridge province of southwest VA. The maps, at both 1:100,000 and 1:24,000 scales, show generalized and detailed bedrock geology grouped by lithology and environmental hazard associations. Also shown are a variety of alluvial, colluvial, debris flow, and landslide deposits, as well as karst features. Multidisciplinary research topics addressed during the mapping included slope evolution and geomorphology, drainage history and terrace distribution, ancient large-scale landsliding, and sinkhole development. The maps have been used by land-use planners and engineering firms in an evaluation of Appalachianmore » paleoseismicity and to assess potential groundwater contamination and subsidence in karst areas. The maps are being used for environmental hazard assessment and site selection of a proposed large electric powerline that crosses the Jefferson National Forest. Also, the maps are proving useful in planning for a public access interpretive geologic enter focused on large-scale slope failures. Some of the largest known landslides in eastern North America took place within the map area. Field comparisons and detailed structure mapping of similar features along the Front Range of the Colorado Rockies indicate that the landslides were probably emplaced during a single catastrophic event of short duration. Although the giles County seismic zone is nearby, stability analyses of slopes in the map area have shown that failure need not have been initiated by a seismic event. Several distinct colluvial units mapped within the area of landslides document a period of extensive weathering that postdates slide emplacement. Radiocarbon dates from landslide sag ponds indicate a minimum age of 9,860 B.P. for emplacement of some of the landslides. These results indicate that pre-slide colluvial and debris flow deposits are at least Pleistocene in age.« less

Altitude of the Top of the Deadwood Formation in the Black Hills area, South Dakota, 1999

USGS Publications Warehouse

Carter, Janet M.; Redden, Jack A.

2000-01-01

This map is a product of the Black Hills Hydrology Study, which was initiated in 1990 to assess the quantity, quality, and distribution of surface water and ground water in the Black Hills area of South Dakota (Driscoll, 1992). This long-term study is a cooperative effort between the U.S. Geological Survey (USGS), the South Dakota Department of Environment and Natural Resources, and the West Dakota Water Development District, which represents various local and county cooperators. This map is part of a series of 1:100,000-scale maps for the study. The maps include a hydrogeologic map, structure-contour maps (altitudes of the tops of formations) for five formations that contain major aquifers in the study area, and potentiometric maps for these five major aquifers (the Inyan Kara, Minnekahta, Minnelusa, Madison, and Deadwood aquifers).The study area consists of the topographically defined Black Hills and adjacent areas located in western South Dakota. The Black Hills area is an elongated, dome-shaped feature, about 125 miles long and 60 miles wide, which was uplifted during the Laramide orogeny (Feldman and Heimlich, 1980). The oldest geologic units in the study area are Precambrian metamorphic and igneous rocks, which are exposed in the central core of the Black Hills. Surrounding the Precambrian core is a layered series of sedimentary rocks including limestones, sandstones, and shales that are exposed in roughly concentric rings around the uplifted flanks of the Black Hills. The bedrock sedimentary units typically dip away from the uplifted Black Hills at angles that approach or exceed 10 degrees near the outcrops, and decrease with distance from the uplift. Many of the sedimentary units contain aquifers, both within and beyond the study area. Recharge to these aquifers occurs from infiltration of precipitation upon the outcrops and, in some cases, from infiltration of streamflow (Hortness and Driscoll, 1998). Artesian conditions generally exist within these aquifers where an upper confining layer is present. Flowing wells and artesian springs that originate from confined aquifers are common around the periphery of the Black Hills.The purpose of this map is to show the altitude of the top (structure contours) of the Deadwood Formation within the area of the Black Hills Hydrology Study. The depth to the top of the Deadwood Formation can be estimated at a specific site by subtracting the altitude of the top of the formation from the topographic elevation, However, caution is urged in determining the depth to the top of the formation in areas on the map where the contours are approximately located.

Altitude of the Top of the Minnelusa Formation in the Black Hills area, South Dakota, 1999

USGS Publications Warehouse

Carter, Janet M.; Redden, Jack A.

2000-01-01

This map is a product of the Black Hills Hydrology Study, which was initiated in 1990 to assess the quantity, quality, and distribution of surface water and ground water in the Black Hills area of South Dakota (Driscoll, 1992). This long-term study is a cooperative effort between the U.S. Geological Survey (USGS), the South Dakota Department of Environment and Natural Resources, and the West Dakota Water Development District, which represents various local and county cooperators. This map is part of a series of 1:100,000-scale maps for the study. The maps include a hydrogeologic map, structure-contour maps (altitudes of the tops of formations) for five formations that contain major aquifers in the study area, and potentiometric maps for these five major aquifers (the Inyan Kara, Minnekahta, Minnelusa, Madison, and Deadwood aquifers).The study area consists of the topographically defined Black Hills and adjacent areas located in western South Dakota. The Black Hills area is an elongated, dome-shaped feature, about 125 miles long and 60 miles wide, which was uplifted during the Laramide orogeny (Feldman and Heimlich, 1980). The oldest geologic units in the study area are Precambrian metamorphic and igneous rocks, which are exposed in the central core of the Black Hills. Surrounding the Precambrian core is a layered series of sedimentary rocks including limestones, sandstones, and shales that are exposed in roughly concentric rings around the uplifted flanks of the Black Hills. The bedrock sedimentary units typically dip away from the uplifted Black Hills at angles that approach or exceed 10 degrees near the outcrops, and decrease with distance from the uplift. Many of the sedimentary units contain aquifers, both within and beyond the study area. Recharge to these aquifers occurs from infiltration of precipitation upon the outcrops and, in some cases, from infiltration of streamflow (Hortness and Driscoll, 1998). Artesian conditions generally exist within these aquifers where an upper confining layer is present. Flowing wells and artesian springs that originate from confined aquifers are common around the periphery of the Black Hills.The purpose of this map is to show the altitude of the top (structure contours) of the Minnelusa Formation within the area of the Black Hills Hydrology Study. The depth to the top of the Minnelusa Formation can be estimated at a specific site by subtracting the altitude of the top of the formation from the topographic elevation. However, caution is urged in determining the depth to the top of the formation in areas on the map where the contours are approximately located.

Altitude of the Top of the Minnekahta Limestone in the Black Hills area, South Dakota, 1999

USGS Publications Warehouse

Carter, Janet M.; Redden, Jack A.

2000-01-01

This map is a product of the Black Hills Hydrology Study, which was initiated in 1990 to assess the quantity, quality, and distribution of surface water and groundwater in the Black Hills area of South Dakota (Driscoli, 1992). This long-term study is a cooperative effort between the U.S. Geological Survey (USGS), the South Dakota Department of environment and Natural Resources, and the West Dakota Water development District, which represents various local and county cooperators. This map is part of a series of 1:100,000-scale maps for the study. The maps include a hydrogeologic map, structure-contour maps (altitudes of the tops of formations) for five formations that contain major aquifers in the study area, and potentiometric maps for these five major aquifers (the Inyan Kara. Minnekahta, Minnelusa, Madison, and Deadwood aquifers).The study area consists of the topographically defined Black Hills and adjacent areas located in western South Dakota. The Black Hills area is an elongated, dome-shaped feature, about 125 miles long and 60 miles wide, which was uplifted during the Laramide orogeny (Feldman and Heimlich, 1980). The oldest geologic units in the study area are Precambrian metamorphic and igneous rocks, which are exposed in the central core of the Black Hills. Surrounding the Precambrian core is a layered series of sedimentary rocks including limestones, sandstones, and shales that are exposed in roughly concentric rings around the uplifted flanks of the Black Hills. The bedrock sedimentary units typically dip away from the uplifted Black Hills at angles that approach or exceed 10 degrees near the outcrops, and decrease with distance from the uplift. Many of the sedimentary units contain aquifers, both within and beyond the study area. Recharge to these aquifers occurs from infiltration of precipitation upon the outcrops and, in some cases, from infiltration of streamflow (Hortness and Driscoll, 1998). Artesian conditions generally exist within these aquifers where an upper confining layer is present. Flowing wells and artesian springs that originate from confined aquifers are common around the periphery of the Black Hills.The purpose of this map is to show the altitude of the top(structure contours) of the Minnekahta limestone within the area of the Black Hills Hydrology Study. The depth to the top of the Minnekahta Limestone can be estimated at a specific site by subtracting the altitude of the top of the formation from the topographic elevation. However, caution is urged in determining the depth to the top of the formation in areas on the map where the contours are approximately located.

Evaluation of carrier collection probability in bifacial interdigitated-back-contact crystalline silicon solar cells by the internal quantum efficiency mapping method

NASA Astrophysics Data System (ADS)

Tachibana, Tomihisa; Tanahashi, Katsuto; Mochizuki, Toshimitsu; Shirasawa, Katsuhiko; Takato, Hidetaka

2018-04-01

Bifacial interdigitated-back-contact (IBC) silicon solar cells with a high bifaciality of 0.91 were fabricated. Screen printing and firing technology were used to reduce the production cost. For the first time, the relationship between the rear side structure and carrier collection probability was evaluated using internal quantum efficiency (IQE) mapping. The measurement results showed that the screen-printed electrode and back surface field (BSF) area led to low IQE. The low carrier collection probability by BSF area can be explained by electrical shading effects. Thus, it is clear that the IQE mapping system is useful to evaluate the IBC cell.

Maps to estimate average streamflow and headwater limits for streams in U.S. Army Corps of Engineers, Mobile District, Alabama and adjacent states

USGS Publications Warehouse

Nelson, George H.

1984-01-01

U.S. Army Corps of Engineers permits are required for discharges of dredged or fill-material downstream from the ' headwaters ' of specified streams. The term ' headwaters ' is defined as the point of a freshwater (non-tidal) stream above which the average flow is less than 5 cu ft/s. Maps of the Mobile District area showing (1) lines of equal average streamflow, and (2) lines of equal drainage areas required to produce an average flow of 5 cu ft/s are contained in this report. These maps are for use by the Corps of Engineers in their permitting program. (USGS)

A Brief History of Soil Mapping and Classification in the USA

NASA Astrophysics Data System (ADS)

Brevik, Eric C.; Hartemink, Alfred E.

2014-05-01

Soil maps show the distribution of soils across an area but also depict soil science theory and ideas on soil formation and classification at the time the maps were created. The national soil mapping program in the USA was established in 1899. The first nation-wide soil map was published by M. Whitney in 1909 and showed soil provinces that were largely based on geology. In 1912, G.N. Coffey published the first country-wide map based on soil properties. The map showed 5 broad soil units that used parent material, color and drainage as diagnostic criteria. The 1913 national map was produced by C.F. Marbut, H.H. Bennett, J.E. Lapham, and M.H. Lapham and showed broad physiographic units that were further subdivided into soil series, soil classes and soil types. In 1935, Marbut drafted a series of maps based on soil properties, but these maps were replaced as official U.S. soil maps in 1938 with the work of M. Baldwin, C.E. Kellogg, and J. Thorp. A series of soil maps similar to modern USA maps appeared in the 1960s with the 7th Approximation followed by revisions with the 1975 and 1999 editions of Soil Taxonomy. This review has shown that soil maps in the United States produced since the early 1900s moved initially from a geologic-based concept to a pedologic concept of soils. Later changes were from property-based systems to process-based, and then back to property-based. The information in this presentation is based on Brevik and Hartemink (2013). Brevik, E.C., and A.E. Hartemink. 2013. Soil Maps of the United States of America. Soil Science Society of America Journal 77:1117-1132. doi:10.2136/sssaj2012.0390.

Mapping the Extent and Magnitude of Severe Flooding Induced by Hurricanes Harvey, Irma, and Maria with Sentinel-1 SAR and InSAR Observations

NASA Astrophysics Data System (ADS)

Zhang, B.; Koirala, R.; Oliver-Cabrera, T.; Wdowinski, S.; Osmanoglu, B.

2017-12-01

Hurricanes can cause winds, rainfall and storm surge, all of which could result in flooding. Between August and September 2017, Hurricanes Harvey, Irma and Maria made landfall over Texas, Florida and Puerto Rico causing destruction and damages. Flood mapping is important for water management and to estimate risks and property damage. Though water gauges are able to monitor water levels, they are normally distributed sparsely. To map flooding products of these extreme events, we use Synthetic Aperture Radar (SAR) observations acquired by the European satellite constellation Sentinel-1. We obtained two acquisitions from before each flooding event, a single acquisition during the hurricane, and two after each event, a total of five acquisitions. We use both amplitude and phase observations to map extent and magnitude of flooding respectively. To map flooding extents, we use amplitude images from before, after and if possible during the hurricane pass. A calibration is used to convert the image raw data to backscatter coefficient, termed sigma nought. We generate a composite of the two image layers using red and green bands to show the change of sigma nought between acquisitions, which directly reflects the extent of flooding. Because inundation can result with either an increase or decrease of sigma nought values depending on the surface scattering characteristics, we map flooded areas in location where sigma nought changes were above a detection threshold. To study magnitude of flooding we study Interferometric Synthetic Aperture Radar (InSAR) phase changes. Changes in the water level can be detected by the radar when the signal is reflected away from water surface and bounces again by another object (e.g. trees and/or buildings) known as double bounce phase. To generate meaningful interferograms, we compare phase information with the nearest water gauge records to verify our results. Preliminary results show that the three hurricanes caused flooding condition over wide area including both rural and urban areas. The flooding in Everglades National Park in Florida following hurricane Irma covered area 1087.35 km2. Flooding in Puerto Rico main island was limited to low flat areas covering 287.84 km2. Preliminary results of the InSAR analysis shows that flooding magnitude reached in some location level of 1 m.

Averaged ratio between complementary profiles for evaluating shape distortions of map projections and spherical hierarchical tessellations

NASA Astrophysics Data System (ADS)

Yan, Jin; Song, Xiao; Gong, Guanghong

2016-02-01

We describe a metric named averaged ratio between complementary profiles to represent the distortion of map projections, and the shape regularity of spherical cells derived from map projections or non-map-projection methods. The properties and statistical characteristics of our metric are investigated. Our metric (1) is a variable of numerical equivalence to both scale component and angular deformation component of Tissot indicatrix, and avoids the invalidation when using Tissot indicatrix and derived differential calculus for evaluating non-map-projection based tessellations where mathematical formulae do not exist (e.g., direct spherical subdivisions), (2) exhibits simplicity (neither differential nor integral calculus) and uniformity in the form of calculations, (3) requires low computational cost, while maintaining high correlation with the results of differential calculus, (4) is a quasi-invariant under rotations, and (5) reflects the distortions of map projections, distortion of spherical cells, and the associated distortions of texels. As an indicator of quantitative evaluation, we investigated typical spherical tessellation methods, some variants of tessellation methods, and map projections. The tessellation methods we evaluated are based on map projections or direct spherical subdivisions. The evaluation involves commonly used Platonic polyhedrons, Catalan polyhedrons, etc. Quantitative analyses based on our metric of shape regularity and an essential metric of area uniformity implied that (1) Uniform Spherical Grids and its variant show good qualities in both area uniformity and shape regularity, and (2) Crusta, Unicube map, and a variant of Unicube map exhibit fairly acceptable degrees of area uniformity and shape regularity.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Yuyu; Smith, Steven J.; Elvidge, Christopher

Accurate information of urban areas at regional and global scales is important for both the science and policy-making communities. The Defense Meteorological Satellite Program/Operational Linescan System (DMSP/OLS) nighttime stable light data (NTL) provide a potential way to map urban area and its dynamics economically and timely. In this study, we developed a cluster-based method to estimate the optimal thresholds and map urban extents from the DMSP/OLS NTL data in five major steps, including data preprocessing, urban cluster segmentation, logistic model development, threshold estimation, and urban extent delineation. Different from previous fixed threshold method with over- and under-estimation issues, in ourmore » method the optimal thresholds are estimated based on cluster size and overall nightlight magnitude in the cluster, and they vary with clusters. Two large countries of United States and China with different urbanization patterns were selected to map urban extents using the proposed method. The result indicates that the urbanized area occupies about 2% of total land area in the US ranging from lower than 0.5% to higher than 10% at the state level, and less than 1% in China, ranging from lower than 0.1% to about 5% at the province level with some municipalities as high as 10%. The derived thresholds and urban extents were evaluated using high-resolution land cover data at the cluster and regional levels. It was found that our method can map urban area in both countries efficiently and accurately. Compared to previous threshold techniques, our method reduces the over- and under-estimation issues, when mapping urban extent over a large area. More important, our method shows its potential to map global urban extents and temporal dynamics using the DMSP/OLS NTL data in a timely, cost-effective way.« less

Application of Radial Basis Functional Link Networks to Exploration for Proterozoic Mineral Deposits in Central Iran

DOE Office of Scientific and Technical Information (OSTI.GOV)

Behnia, Pouran

2007-06-15

The metallogeny of Central Iran is characterized mainly by the presence of several iron, apatite, and uranium deposits of Proterozoic age. Radial Basis Function Link Networks (RBFLN) were used as a data-driven method for GIS-based predictive mapping of Proterozoic mineralization in this area. To generate the input data for RBFLN, the evidential maps comprising stratigraphic, structural, geophysical, and geochemical data were used. Fifty-eight deposits and 58 'nondeposits' were used to train the network. The operations for the application of neural networks employed in this study involve both multiclass and binary representation of evidential maps. Running RBFLN on different input datamore » showed that an increase in the number of evidential maps and classes leads to a larger classification sum of squared error (SSE). As a whole, an increase in the number of iterations resulted in the improvement of training SSE. The results of applying RBFLN showed that a successful classification depends on the existence of spatially well distributed deposits and nondeposits throughout the study area.« less

Landslides triggered by Hurricane Mitch in Guatemala -- inventory and discussion

USGS Publications Warehouse

Bucknam, Robert C.; Coe, Jeffrey A.; Chavarria, Manuel Mota; Godt, Jonathan W.; Tarr, Arthur C.; Bradley, Lee-Ann; Rafferty, Sharon A.; Hancock, Dean; Dart, Richard L.; Johnson, Margo L.

2001-01-01

The torrential rains that accompanied Hurricane Mitch in October and November of 1998 triggered thousands of landslides in the moderate to steep terrain bordering the Motagua and Polochic Rivers in eastern Guatemala. Using aerial photographs taken between January and March 2000 we mapped all visible landslides larger than about 15 m in minimum dimension in a study area of 10,000 km2 encompassing twenty 1:50,000-scale topographic map quadrangles. Rainfall from Hurricane Mitch was exceptional because it was geographically widespread, prolonged over a period of about a week, moderate to heavy in intensity, and occurred at the end of the rainy season when the ground already had a high moisture content. As documented in this report, this type of rainfall, on saturated or nearly saturated ground, has the capability to trigger both shallow and deep-seated landslides over a large area. We mapped about 11,500 landslides in the study area. The mapped landslides were of two general types: relatively small, translational and rotational landslides that commonly mobilized into debris flows and covered less than several hectares in area (not including flow paths), and large, commonly translational, landslides that sometimes generated debris flows and covered between 15 ha and 25 ha (not including flow paths). The main concentrations of landslides are on moderate-to-steep hillslopes underlain by diverse geologic units. For the purpose of describing the mapped landslides, we divided the study area into five distinct regions based on differing geologic and geomorphic characteristics. These regions include the upper Polochic valley and surrounding highlands, the central Sierra de las Minas, the hills surrounding La Union and Zacapa, the eastern Sierra de las Minas, and the border region with Honduras. All of these areas received between 200 mm and 600 mm of rain over a 13-day period between October 25 and November 6. The highest rainfall amounts (400 mm to 600 mm) occurred in the Upper Polochic valley and surrounding highlands and in the central Sierra de las Minas. The lower rainfall amounts (200 mm to 400 mm) occurred in the hills surrounding La Union, the eastern Sierra de las Minas, and in the border region with Honduras. In general, the rainfall received in these areas is roughly equivalent to the average precipitation received in a 1-year period. We used 10-m digital elevation models (DEMs) generated from contours on two quadrangles in the central Sierra de las Minas to create a map showing areas that were susceptible to landslides during Hurricane Mitch. To create the Hurricane Mitch susceptibility map, we developed a susceptibility threshold equation based on elevation and gradient. The analysis indicates that, at least on two quadrangles, gradients less than 9? were not susceptible to landslides during Hurricane Mitch. The slope of the line defined by the threshold equation indicates that less rainfall was required to initiate landslides on steep gradients than on shallow gradients. Ninety percent of the mapped landslides that were triggered by Hurricane Mitch are within the susceptible zone shown on the map. Eightysix percent of landslides that were mapped as predating Hurricane Mitch, and all landslides mapped as postdating Hurricane Mitch, are within the susceptible zone. We used LAHARZ software to model the potential downstream area affected by debris if a large landslide dam on the Rio La Lima were to fail. The model shows that the area affected would be similar to the area that was affected by a debris flow that mobilized from a large landslide along the Rio La Lima during Hurricane Mitch. The characteristics of rainfall-triggered landslides described in this report can be used as a partial guide to future landslide activity triggered by rainstorms. On the basis of existing data, hazardous areas include: moderate to steep hillslopes and

Mapping the mineralogy and lithology of Canyonlands, Utah with imaging spectrometer data and the multiple spectral feature mapping algorithm

NASA Technical Reports Server (NTRS)

Clark, Roger N.; Swayze, Gregg A.; Gallagher, Andrea

1992-01-01

The sedimentary sections exposed in the Canyonlands and Arches National Parks region of Utah (generally referred to as 'Canyonlands') consist of sandstones, shales, limestones, and conglomerates. Reflectance spectra of weathered surfaces of rocks from these areas show two components: (1) variations in spectrally detectable mineralogy, and (2) variations in the relative ratios of the absorption bands between minerals. Both types of information can be used together to map each major lithology and the Clark spectral features mapping algorithm is applied to do the job.

Pluto Topography and Composition Map

NASA Image and Video Library

2017-09-28

These maps are from New Horizons' data on the topography (top) and composition (bottom) of Pluto's surface. In the high-resolution topographical map, the highlighted red region is high in elevation. The map below, showing the composition, indicates the same section also contains methane, color-coded in orange. One can see the orange features spread into the fuzzier, lower-resolution data that covers the rest of the globe, meaning those areas, too, are high in methane, and therefore likely to be high in elevation. https://photojournal.jpl.nasa.gov/catalog/PIA22036

The difference between the potentiometric surfaces of the Magothy Aquifer of September 1986 and September 1988 in southern Maryland

USGS Publications Warehouse

Mack, Frederick K.; Andreasen, David C.; Curtin, Stephen E.; Wheeler, Judith C.

1990-01-01

A map was prepared that shows the net change in the potentiometric surface of the Magothy aquifer (in the Cretaceous Magothy Formation) in southern Maryland from the fall of 1986 to the fall of 1988. The map, based on water level measurements from 79 observation wells, shows that during the 2 year period the potentiometric surface declined less than 5 ft in most of the northern part of the study area and more than 10 ft in a 4-sq-mi area in northern Charles County. Net water-level rises of as much as 2 ft were measured in central Charles County. (USGS)

Summary geochemical maps for samples of rock, stream sediment, and nonmagnetic heavy-mineral concentrate, Sweetwater Roadless Area, Mono County, California and Lyon and Douglas Counties, Nevada

USGS Publications Warehouse

Chaffee, Maurice A.

1986-01-01

Map A shows the locations of all sites where rock samples were collected for this report and the distributions of anomalous concentrations for 12 elements in the 127 rock samples collected. In a similar manner, map B shows the collection sites for 59 samples of minus-60-mesh stream sediment, and 59 samples of nonmagnetic heavy-mineral concentrate derived from stream sediment and also shows the distributions of anomalous concentrations for 13 elements in the stream-sediment samples and 17 elements in the concentrate samples. Map C shows outlines of those drainage basins containing samples of stream sediment and concentrate with anomalous element concentrations and also shows weighted values for each outlined basin based on the number of elements with anomalous concentrations in each stream-sediment and concentrate sample and on the degree to which these concentrations are anomalous in each sample.

Alteration mineral mapping for iron prospecting using ETM+ data, Tonkolili iron field, northern Sierra Leone

NASA Astrophysics Data System (ADS)

Mansaray, Lamin R.; Liu, Lei; Zhou, Jun; Ma, Zhimin

2013-10-01

The Tonkolili iron field in northern Sierra Leone has the largest known iron ore deposit in Africa. It occurs in a greenstone belt in an Achaean granitic basement. This study focused mainly on mapping areas with iron-oxide and hydroxyl bearing minerals, and identifying potential areas for haematite mineralization and banded iron formations (BIFs) in Tonkolili. The predominant mineral assemblage at the surface (laterite duricrust) of this iron field is haematitegoethite- limonite ±magnetite. The mineralization occurs in quartzitic banded ironstones, layered amphibolites, granites, schists and hornblendites. In this study, Crosta techniques were applied on Enhanced Thematic Mapper (ETM+) data to enhance areas with alteration minerals and target potential areas of haematite and BIF units in the Tonkolili iron field. Synthetic analysis shows that alteration zones mapped herein are consistent with the already discovered magnetite BIFs in Tonkolili. Based on the overlaps of the simplified geological map and the remote sensing-based alteration mineral maps obtained in this study, three new haematite prospects were inferred within, and one new haematite prospect was inferred outside the tenement boundary of the Tonkolili exploration license. As the primary iron mineral in Tonkolili is magnetite, the study concludes that, these haematite prospects could also be underlain by magnetite BIFs. This study also concludes that, the application of Crosta techniques on ETM+ data is effective not only in mapping iron-oxide and hydroxyl alterations but can also provide a basis for inferring areas of potential iron resources in Algoma-type banded iron formations (BIFs), such as those in the Tonkolili field.

Standardized morbidity ratio for leptospirosis mapping in Malaysia

NASA Astrophysics Data System (ADS)

Awang, Aznida Che; Samat, Nor Azah

2017-05-01

Leptospirosis is a worldwide zoonotic disease that affects human health in many parts of the world including Malaysia. Leptospirosis is a disease caused by the infection of pathogenic Leptospira genus called Spirochaetes. Leptospirosis can be transmitted directly or indirectly from rats to human. The human infection is usually caused by human contact with urine or tissues of infected animal. This disease can be spread through mucus membrane such as mouth, nose and eyes, ingestion of contaminated food and water and also exposed injured skin to contaminated water or soil. There is still no vaccine currently available for the prevention or treatment of leptospirosis disease but this disease can be treated if it is diagnosed early. Therefore, the aim of this study is to estimate the relative risk for leptospirosis disease based initially on the most common statistic used in the study of disease mapping called Standardized Morbidity Ratio (SMR). We then apply SMR to leptospirosis data obtained in Malaysia. The results show that the states of Melaka have very high risk areas. The states of Kedah, Terengganu and Kelantan are identified as high risk areas. The states of Perak, Perlis, Sabah and Sarawak showed medium risk areas. This is followed by low risk by other states except Pahang, Johor and Labuan with very low risk areas. In conclusion, SMR method is the best method for mapping leptospirosis because by referring to the relative risk maps, the states that deserve closer look and disease prevention can be identified.

Subsidence in the Central Valley, California 2007 - present measured by InSAR

NASA Astrophysics Data System (ADS)

Farr, T. G.; Liu, Z.; Jones, C. E.

2015-12-01

Subsidence caused by groundwater pumping in the rich agricultural area of California's Central Valley has been a problem for decades. Over the last few years, interferometric synthetic aperture radar (InSAR) observations from satellite and aircraft platforms have been used to produce maps of subsidence with ~cm accuracy. For this study, we have obtained and analyzed Japanese PALSAR data for 2006 - 2011, Canadian Radarsat-1 data for 2011 - 2013, Radarsat-2 data for 2012 - 2015, and ESA's Sentinel-1A for 2015 and produced maps of subsidence for those periods. High resolution InSAR data were also acquired along the California Aqueduct by the NASA UAVSAR from 2013 - 2015. Using multiple scenes acquired by these systems, we were able to produce the time histories of subsidence at selected locations and transects showing how subsidence varies both spatially and temporally. The maps show that subsidence is continuing in areas with a history of subsidence and that the rates and areas affected have increased due to increased groundwater extraction during the extended western US drought. The high resolution maps from UAVSAR were used to identify and quantify new, highly localized areas of accelerated subsidence along the California Aqueduct that occurred in 2014. The California Department of Water Resources (DWR) funded this work to provide the background and an update on subsidence in the Central Valley to support future policy. Geographic Information System (GIS) files are being furnished to DWR for further analysis of the 4 dimensional subsidence time-series maps. Part of this work was carried out at the Jet Propulsion Laboratory, California Institute of Technology, under contract with NASA.

Coastal habitat mapping in the Aegean Sea using high resolution orthophoto maps

NASA Astrophysics Data System (ADS)

Topouzelis, Konstantinos; Papakonstantinou, Apostolos; Doukari, Michaela; Stamatis, Panagiotis; Makri, Despina; Katsanevakis, Stelios

2017-09-01

The significance of coastal habitat mapping lies in the need to prevent from anthropogenic interventions and other factors. Until 2015, Landsat-8 (30m) imagery were used as medium spatial resolution satellite imagery. So far, Sentinel-2 satellite imagery is very useful for more detailed regional scale mapping. However, the use of high resolution orthophoto maps, which are determined from UAV data, is expected to improve the mapping accuracy. This is due to small spatial resolution of the orthophoto maps (30 cm). This paper outlines the integration of UAS for data acquisition and Structure from Motion (SfM) pipeline for the visualization of selected coastal areas in the Aegean Sea. Additionally, the produced orthophoto maps analyzed through an object-based image analysis (OBIA) and nearest-neighbor classification for mapping the coastal habitats. Classification classes included the main general habitat types, i.e. seagrass, soft bottom, and hard bottom The developed methodology applied at the Koumbara beach (Ios Island - Greece). Results showed that UAS's data revealed the sub-bottom complexity in large shallow areas since they provide such information in the spatial resolution that permits the mapping of seagrass meadows with extreme detail. The produced habitat vectors are ideal as reference data for studies with satellite data of lower spatial resolution.

Geospatial association of endemicity of ataxic polyneuropathy and highly cyanogenic cassava cultivars.

PubMed

Oluwole, Olusegun Steven Ayodele; Oludiran, Adeyinka

2013-09-14

Exposure to cyanide from cassava foods is present in communities where ataxic polyneuropathy is endemic. Ataxic polyneuropathy is endemic in coastal parts of southwest and southeast Nigeria, and coastal Newala, south India, but it has been reported in epidemic or endemic forms from Africa, Asia, or Caribbean. This study was done to determine if cyanogenicity of cassava cultivars is higher in lowland than highland areas, and if areas of endemicity of ataxic polyneuropathy colocalize with areas of highest cyanogenicity of cassava. Roots of cassava cultivars were collected from 150 farmers in 32 of 37 administrative areas in Nigeria. Global positioning system was used to determine the location of the roots. Roots were assayed for concentrations of cyanogens. Thin Plate Spline regression was used to produce the contour map of cyanogenicity of the study area. Contour maps of altitude of the endemic areas were produced. Relationship of cyanogenicity of cassava cultivars and altitude, and of locations of areas of high cyanogenicity and areas of endemicity were determined. Geometrical mean (95% CI) cyanogen concentration was 182 (142-233) mg HCN eq/kg dry wt for cassava cultivars in areas ≤ 25 m above sea level, but 54 (43-66) mg HCN eq/kg dry wt for areas > 375 m. Non-spatial linear regression of altitude on logarithm transformed concentrations of cyanogens showed highly significant association, (p < 0.0001). Contour map of concentrations of cyanogens in cassava cultivars in Nigeria showed four areas with average concentrations of cassava cyanogens > 250 mg HCN eq/kg dry wt, and one area of moderately high cyanogen concentration > 150 mg HCN eq/kg dry wt. The endemic areas colocalized with areas of highest cassava cyanogenicity in lowland areas close to the Atlantic Ocean. This study shows strong geospatial association of areas of endemicity of ataxic polyneuropathy and areas of highest cyanogenicity of cassava cultivars. Finding of higher cyanogenicity of cassava in lowland than highland areas indicate strong influence of altitude on expression of cyanogens in cassava cultivars.

Geospatial association of endemicity of ataxic polyneuropathy and highly cyanogenic cassava cultivars

PubMed Central

2013-01-01

Background Exposure to cyanide from cassava foods is present in communities where ataxic polyneuropathy is endemic. Ataxic polyneuropathy is endemic in coastal parts of southwest and southeast Nigeria, and coastal Newala, south India, but it has been reported in epidemic or endemic forms from Africa, Asia, or Caribbean. This study was done to determine if cyanogenicity of cassava cultivars is higher in lowland than highland areas, and if areas of endemicity of ataxic polyneuropathy colocalize with areas of highest cyanogenicity of cassava. Methods Roots of cassava cultivars were collected from 150 farmers in 32 of 37 administrative areas in Nigeria. Global positioning system was used to determine the location of the roots. Roots were assayed for concentrations of cyanogens. Thin Plate Spline regression was used to produce the contour map of cyanogenicity of the study area. Contour maps of altitude of the endemic areas were produced. Relationship of cyanogenicity of cassava cultivars and altitude, and of locations of areas of high cyanogenicity and areas of endemicity were determined. Results Geometrical mean (95% CI) cyanogen concentration was 182 (142–233) mg HCN eq/kg dry wt for cassava cultivars in areas ≤ 25 m above sea level, but 54 (43–66) mg HCN eq/kg dry wt for areas > 375 m. Non-spatial linear regression of altitude on logarithm transformed concentrations of cyanogens showed highly significant association, (p < 0.0001). Contour map of concentrations of cyanogens in cassava cultivars in Nigeria showed four areas with average concentrations of cassava cyanogens > 250 mg HCN eq/kg dry wt, and one area of moderately high cyanogen concentration > 150 mg HCN eq/kg dry wt. The endemic areas colocalized with areas of highest cassava cyanogenicity in lowland areas close to the Atlantic Ocean. Conclusion This study shows strong geospatial association of areas of endemicity of ataxic polyneuropathy and areas of highest cyanogenicity of cassava cultivars. Finding of higher cyanogenicity of cassava in lowland than highland areas indicate strong influence of altitude on expression of cyanogens in cassava cultivars. PMID:24034556

Implementation of landslide susceptibility maps in Lower Austria as part of risk governance

NASA Astrophysics Data System (ADS)

Bell, Rainer; Petschko, Helene; Bauer, Christian; Glade, Thomas; Granica, Klaus; Heiss, Gerhard; Leopold, Philip; Pomaroli, Gilbert; Proske, Herwig; Schweigl, Joachim

2013-04-01

Landslides frequently cause damage to agricultural land and infrastructure in Lower Austria - a province of Austria. Also settlements and people are threatened by landslides. To reduce landslide risks and to prevent the establishment of new settlements in highly landslide prone areas, the project "MoNOE" (Method development for landslide susceptibility modeling in Lower Austria) was set up by the provincial government. The main aim of the project is the development of methods to model rock fall and slide susceptibility for an area of approx. 15,900 km2 and to implement the resulting susceptibility maps into the spatial planning strategies of the state. Right from the beginning of the project a close cooperation between the involved scientists and the stakeholders from the Geological Survey of Lower Austria and the Department of Spatial Planning and Regional Policy of Lower Austria was established to ensure that method development and final susceptibility maps meet exactly the needs and demands of the stakeholders. This posed huge challenges, together with its realization in the large study area and a (heterogeneous) complex geological situation,. Limitations were given by restricted data availability (e.g. for geology or landslide inventories) in such a large study area. Rock fall susceptibility was modeled by a combined approach of determining rock fall release areas by empirical slope thresholds (dependent on geology) followed by empirical run-out modeling. Slide susceptibility was modeled based on the statistical approaches of weights of evidence (WofE) and generalized additive models (GAM) by two different research groups. Huge efforts were spent on the validation of all susceptibility models. In a later stage of the project we found that the best scientific maps are not necessarily the best maps to be implemented in spatial planning strategies. Thus, in close cooperation with the stakeholders, decisions had to be taken to find the best resolution of the maps, the number of susceptibility classes, their colour and naming, as well as on the instructions for actions referring to each susceptibility class respectively. All susceptibility maps showed very good validation results. Both, the WofE and the GAM slide susceptibility map showed high median AUROC values of 0.9 and the geomorphological plausibility proved to be very good in both cases. Due to these results it was concluded the stakeholders should take the decision which of the two slide susceptibility maps should be used. This decision was performed as a blind test providing resulting maps and their respective performance measures but coded with a color so that the stakeholders did not know which maps were produced by whom and with which method. This presentation is thus focusing on a detailed description of all these aspects and it is discussed how this participative approach led to a high acceptance of the final landslide susceptibility maps by the stakeholders. Consequently these maps are going to be implemented in the spatial planning strategies soon.

Wetland Classification for Black Duck Habitat Management Using Combined Polarimetric RADARSAT 2 and SPOT Imagery

NASA Astrophysics Data System (ADS)

Zhang, W.; Hu, B.; Brown, G.

2018-04-01

The black duck population has decreased significantly due to loss of its breeding habitat. Wetlands are an important feature that relates to habitat management and requires monitoring. Synthetic Aperture Radar (SAR) systems are helpful to map the wetland as the microwave signals are sensitive to water content and can be used to map surface water extent, saturated soils, and flooded vegetation. In this study, RadarSat 2 Polarimetric data is employed to map surface water and track changes in extent over the years through image thresholding and reviewed different approaches of Polarimetric decompositions for detecting flooded vegetation. Also, object-based analysis associated with beaver activity is conducted with combined multispectral SPOT satellite imagery. Results show SAR data has proven ability to improve mapping open water areas and locate flooded vegetation areas.

Environmental aspects of engineering geological mapping in the United States

USGS Publications Warehouse

Radbruch-Hall, Dorothy H.

1979-01-01

Many engineering geological maps at different scales have been prepared for various engineering and environmental purposes in regions of diverse geological conditions in the United States. They include maps of individual geological hazards and maps showing the effect of land development on the environment. An approach to assessing the environmental impact of land development that is used increasingly in the United States is the study of a single area by scientists from several disciplines, including geology. A study of this type has been made for the National Petroleum Reserve in northern Alaska. In the San Francisco Bay area, a technique has been worked out for evaluating the cost of different types of construction and land development in terms of the cost of a number of kinds of earth science factors. ?? 1979 International Association of Engineering Geology.

Incorporating Geographic Information Systems (GIS) into program evaluation: lessons from a rural medicine initiative.

PubMed

Booza, Jason C; Bridge, Patrick D; Neale, Anne Victoria; Schenk, Maryjean

2010-01-01

To address the shortage of physicians practicing in rural areas of Michigan, the Wayne State University School of Medicine developed an integrated rural core curriculum to interest students in rural practice careers. Here we focus on the evaluation strategy used to determine the extent to which students in the new rural medicine interest group who self-identified as selecting a rural clerkship or externship did secure a clinical training experience in a rural setting. Three measures of rurality were compared to determine whether students were placed in rural training settings: (1) the percentage of the county living in rural areas; (2) a county-level dichotomous measure of rural/nonrural; and (3) a dichotomous measure based on urban area boundaries within the county. Practice address and geographic data were integrated into geographic information systems software, which we used to map out rural characteristics of Michigan counties through a process called thematic mapping; this shows characteristic variation by color-shading geographic features. In addition, reference maps were created showing the boundaries of urban areas and metropolitan/micropolitan areas. Once these processes were completed, we overlaid the practice location on the contextual-level geographic features to produce a visual representation of the relationship between student placement and rural areas throughout the state. The outcome of student placement in rural practices varied by the definition of rural. We concluded that, although students were not placed in the most rural areas of Michigan, they received clerkship or externship training near rural areas or in semirural areas. This process evaluation had a direct impact on program management by highlighting gaps in preceptor recruitment. A greater effort is being made to recruit physicians for more rural areas of the state rather than urban and semirural areas. Geographic information systems mapping also defined levels of ruralism for students to help them make informed selections of training sties. This is especially important for students who are not sure about a rural experience and might be discouraged by placement in a remote rural area.

Hydrogeologic characteristics and geospatial analysis of water-table changes in the alluvium of the lower Arkansas River Valley, southeastern Colorado, 2002, 2008, and 2015

USGS Publications Warehouse

Holmberg, Michael J.

2017-05-15

The U.S. Geological Survey in cooperation with the Lower Arkansas Valley Water Conservancy District measures groundwater levels periodically in about 100 wells completed in the alluvial material of the Arkansas River Valley in Pueblo, Crowley, Otero, Bent, and Prowers Counties in southeastern Colorado, of which 95 are used for the analysis in this report. The purpose of this report is to provide information to water-resource administrators, managers, planners, and users about groundwater characteristics in the alluvium of the lower Arkansas Valley extending roughly 150 miles between Pueblo Reservoir and the Colorado-Kansas State line. This report includes three map sheets showing (1) bedrock altitude at the base of the alluvium of the lower Arkansas Valley; (2) estimated spring-to-spring and fall-to-fall changes in water-table altitude between 2002, 2008, and 2015; and (3) estimated saturated thickness in the alluvium during spring and fall of 2002, 2008, and 2015, and thickness of the alluvium in the lower Arkansas Valley. Water-level changes were analyzed by geospatial interpolation methods.Available data included all water-level measurements made between January 1, 2001, and December 31, 2015; however, only data from fall and spring of 2002, 2008, and 2015 are mapped in this report. To account for the effect of John Martin Reservoir in Bent County, Colorado, lake levels at the reservoir were assigned to points along the approximate shoreline and were included in the water-level dataset. After combining the water-level measurements and lake levels, inverse distance weighting was used to interpolate between points and calculate the altitude of the water table for fall and spring of each year for comparisons. Saturated thickness was calculated by subtracting the bedrock surface from the water-table surface. Thickness of the alluvium was calculated by subtracting the bedrock surface from land surface using a digital elevation model.In order to analyze the response of the alluvium to varying environmental and anthropogenic conditions, the percentage of area of the lower Arkansas Valley showing an absolute change of 3 feet or less was calculated for each of the six water-table altitude change maps. For fall water-table altitude change maps, the periods between 2002 and 2008, 2008 and 2015, and 2002 and 2015 showed that 86.5 percent, 85.2 percent, and 66.3 percent of the study area, respectively, showed a net change of 3 feet or less. In the spring water-table altitude change maps these periods showed a net change of 3 feet or less in 94.4 percent, 96.1 percent, and 90.2 percent of the study area, respectively. While the estimated change in water-table altitude was slightly greater and more variable in fall-to-fall comparisons, these high percentages of area with relatively small net changes indicated that, at least in comparisons of the years presented, there was not a large amount of fluctuation in the altitude of the water table.The saturated thickness in the lower Arkansas Valley was between 25 and 50 feet in 34.4 to 35.9 percent of the study area, depending on the season and year. Between 30.2 and 35.6 percent of the area showed saturated thicknesses between 0 and 25 feet. Less than 1 percent of the area showed a saturated thickness greater than 200 feet in all mapped seasons and years.

Potential Deep Seated Landslide Mapping from Various Temporal Data - Benchmark, Aerial Photo, and SAR

NASA Astrophysics Data System (ADS)

Wang, Kuo-Lung; Lin, Jun-Tin; Lee, Yi-Hsuan; Lin, Meei-Ling; Chen, Chao-Wei; Liao, Ray-Tang; Chi, Chung-Chi; Lin, Hsi-Hung

2016-04-01

Landslide is always not hazard until mankind development in highly potential area. The study tries to map deep seated landslide before the initiation of landslide. Study area in central Taiwan is selected and the geological condition is quite unique, which is slate. Major direction of bedding in this area is northeast and the dip ranges from 30-75 degree to southeast. Several deep seated landslides were discovered in the same side of bedding from rainfall events. The benchmarks from 2002 ~ 2009 are in this study. However, the benchmarks were measured along Highway No. 14B and the road was constructed along the peak of mountains. Taiwan located between sea plates and continental plate. The elevation of mountains is rising according to most GPS and benchmarks in the island. The same trend is discovered from benchmarks in this area. But some benchmarks are located in landslide area thus the elevation is below average and event negative. The aerial photos from 1979 to 2007 are used for orthophoto generation. The changes of land use are obvious during 30 years and enlargement of river channel is also observed in this area. Both benchmarks and aerial photos have discovered landslide potential did exist this area but how big of landslide in not easy to define currently. Thus SAR data utilization is adopted in this case. DInSAR and SBAS sar analysis are used in this research and ALOS/PALSAR from 2006 to 2010 is adopted. DInSAR analysis shows that landslide is possible mapped but the error is not easy to reduce. The error is possibly form several conditions such as vegetation, clouds, vapor, etc. To conquer the problem, time series analysis, SBAS, is adopted in this research. The result of SBAS in this area shows that large deep seated landslides are easy mapped and the accuracy of vertical displacement is reasonable.

Image Analysis for Facility Siting: a Comparison of Lowand High-altitude Image Interpretability for Land Use/land Cover Mapping

NASA Technical Reports Server (NTRS)

Borella, H. M.; Estes, J. E.; Ezra, C. E.; Scepan, J.; Tinney, L. R.

1982-01-01

For two test sites in Pennsylvania the interpretability of commercially acquired low-altitude and existing high-altitude aerial photography are documented in terms of time, costs, and accuracy for Anderson Level II land use/land cover mapping. Information extracted from the imagery is to be used in the evaluation process for siting energy facilities. Land use/land cover maps were drawn at 1:24,000 scale using commercially flown color infrared photography obtained from the United States Geological Surveys' EROS Data Center. Detailed accuracy assessment of the maps generated by manual image analysis was accomplished employing a stratified unaligned adequate class representation. Both 'area-weighted' and 'by-class' accuracies were documented and field-verified. A discrepancy map was also drawn to illustrate differences in classifications between the two map scales. Results show that the 1:24,000 scale map set was more accurate (99% to 94% area-weighted) than the 1:62,500 scale set, especially when sampled by class (96% to 66%). The 1:24,000 scale maps were also more time-consuming and costly to produce, due mainly to higher image acquisition costs.

Regional liquefaction hazard evaluation following the 2010-2011 Christchurch (New Zealand) earthquake sequence

NASA Astrophysics Data System (ADS)

Begg, John; Brackley, Hannah; Irwin, Marion; Grant, Helen; Berryman, Kelvin; Dellow, Grant; Scott, David; Jones, Katie; Barrell, David; Lee, Julie; Townsend, Dougal; Jacka, Mike; Harwood, Nick; McCahon, Ian; Christensen, Steve

2013-04-01

Following the damaging 4 Sept 2010 Mw7.1 Darfield Earthquake, the 22 Feb 2011 Christchurch Earthquake and subsequent damaging aftershocks, we completed a liquefaction hazard evaluation for c. 2700 km2 of the coastal Canterbury region. Its purpose was to distinguish at a regional scale areas of land that, in the event of strong ground shaking, may be susceptible to damaging liquefaction from areas where damaging liquefaction is unlikely. This information will be used by local government for defining liquefaction-related geotechnical investigation requirements for consent applications. Following a review of historic records of liquefaction and existing liquefaction assessment maps, we undertook comprehensive new work that included: a geologic context from existing geologic maps; geomorphic mapping using LiDAR and integrating existing soil map data; compilation of lithological data for the surficial 10 m from an extensive drillhole database; modelling of depth to unconfined groundwater from existing subsurface and surface water data. Integrating and honouring all these sources of information, we mapped areas underlain by materials susceptible to liquefaction (liquefaction-prone lithologies present, or likely, in the near-surface, with shallow unconfined groundwater) from areas unlikely to suffer widespread liquefaction damage. Comparison of this work with more detailed liquefaction susceptibility assessment based on closely spaced geotechnical probes in Christchurch City provides a level of confidence in these results. We tested our susceptibility map by assigning a matrix of liquefaction susceptibility rankings to lithologies recorded in drillhole logs and local groundwater depths, then applying peak ground accelerations for four earthquake scenarios from the regional probabilistic seismic hazard model (25 year return = 0.13g; 100 year return = 0.22g; 500 year return = 0.38g and 2500 year return = 0.6g). Our mapped boundary between liquefaction-prone areas and areas unlikely to sustain heavy damage proved sound. In addition, we compared mapped liquefaction extents (derived from post-earthquake aerial photographs) from the 4 Sept 2010 Mw7.1 and 22 Feb 2011 Mw6.2 earthquakes with our liquefaction susceptibility map. The overall area of liquefaction for these two earthquakes was similar, and statistics show that for the first (large regional) earthquake, c. 93% of mapped liquefaction fell within the liquefaction-prone area, and for the second (local, high peak ground acceleration) earthquake, almost 99% fell within the liquefaction-prone area. We conclude that basic geological and groundwater data when coupled with LiDAR data can usefully delineate areas susceptible to liquefaction from those unlikely to suffer damaging liquefaction. We believe that these techniques can be used successfully in many other cities around the world.

Map Projections and the Visual Detective: How to Tell if a Map Is Equal-Area, Conformal, or Neither

ERIC Educational Resources Information Center

Olson, Judy M.

2006-01-01

The ability to see whether a map is equal-area, conformal, or neither is useful for looking intelligently at large-area maps. For example, only if a map is equal-area can reliable judgments of relative size be made. If a map is equal-area, latitude-longitude cells are equal in size between a given pair of parallels, the cells between a given pair…

Land cover mapping of the National Park Service northwest Alaska management area using Landsat multispectral and thematic mapper satellite data

USGS Publications Warehouse

Markon, C.J.; Wesser, Sara

1998-01-01

A land cover map of the National Park Service northwest Alaska management area was produced using digitally processed Landsat data. These and other environmental data were incorporated into a geographic information system to provide baseline information about the nature and extent of resources present in this northwest Alaskan environment.This report details the methodology, depicts vegetation profiles of the surrounding landscape, and describes the different vegetation types mapped. Portions of nine Landsat satellite (multispectral scanner and thematic mapper) scenes were used to produce a land cover map of the Cape Krusenstern National Monument and Noatak National Preserve and to update an existing land cover map of Kobuk Valley National Park Valley National Park. A Bayesian multivariate classifier was applied to the multispectral data sets, followed by the application of ancillary data (elevation, slope, aspect, soils, watersheds, and geology) to enhance the spectral separation of classes into more meaningful vegetation types. The resulting land cover map contains six major land cover categories (forest, shrub, herbaceous, sparse/barren, water, other) and 19 subclasses encompassing 7 million hectares. General narratives of the distribution of the subclasses throughout the project area are given along with vegetation profiles showing common relationships between topographic gradients and vegetation communities.

Regional Disparities in Online Map User Access Volume and Determining Factors

NASA Astrophysics Data System (ADS)

Li, R.; Yang, N.; Li, R.; Huang, W.; Wu, H.

2017-09-01

The regional disparities of online map user access volume (use `user access volume' in this paper to indicate briefly) is a topic of growing interest with the increment of popularity in public users, which helps to target the construction of geographic information services for different areas. At first place we statistically analysed the online map user access logs and quantified these regional access disparities on different scales. The results show that the volume of user access is decreasing from east to the west in China as a whole, while East China produces the most access volume; these cities are also the crucial economic and transport centres. Then Principal Component Regression (PCR) is applied to explore the regional disparities of user access volume. A determining model for Online Map access volume is proposed afterwards, which indicates that area scale is the primary determining factor for regional disparities, followed by public transport development level and public service development level. Other factors like user quality index and financial index have very limited influence on the user access volume. According to the study of regional disparities in user access volume, map providers can reasonably dispatch and allocate the data resources and service resources in each area and improve the operational efficiency of the Online Map server cluster.

Surficial Geologic Map of the Pocasset-Provincetown-Cuttyhunk-Nantucket 24-Quadrangle Area of Cape Cod and Islands, Southeast Massachusetts

USGS Publications Warehouse

Stone, Byron D.; DiGiacomo-Cohen, Mary L.

2006-01-01

The surficial geologic map layer shows the distribution of nonlithified earth materials at land surface in an area of 24 7.5-minute quadrangles (555 mi2 total) in southeast Massachusetts. Across Massachusetts, these materials range from a few feet to more than 500 ft in thickness. They overlie bedrock, which crops out in upland hills and as resistant ledges in valley areas. On Cape Cod and adjacent islands, these materials completely cover the bedrock surface. The geologic map differentiates surficial materials of Quaternary age on the basis of their lithologic characteristics (such as grain size and sedimentary structures), constructional geomorphic features, stratigraphic relations, and age. Surficial earth materials significantly affect human use of the land, and an accurate description of their distribution is particularly important for assessing water resources, construction aggregate resources, and earth-surface hazards, and for making land-use decisions. This work is part of a comprehensive study to produce a statewide digital map of the surficial geology at a 1:24,000-scale level of accuracy. This report includes explanatory text (PDF), quadrangle maps at 1:24,000 scale (PDF files), GIS data layers (ArcGIS shapefiles), metadata for the GIS layers, scanned topographic base maps (TIF), and a readme.txt file.

UAS close range remote sensing for mapping coastal environments

NASA Astrophysics Data System (ADS)

Papakonstantinou, Apostolos; Topouzelis, Kostantinos; Doukari, Michaela

2017-09-01

Coastline change and marine litter concentration in shoreline zones are two different emerging problems indicating the vulnerability as well as the quality of a coastal environment. Both problems present spatiotemporal changes due to weather and anthropogenic factors. Traditionally spatiotemporal changes in coastal environments are monitored using high-resolution satellite images and manned surveys. The last years, Unmanned Aerial Systems (UAS) are used as additional tool for monitoring environmental phenomena in sensitive coastal areas. In this study, two different case studies for mapping emerging coastal phenomena i.e. coastline changes and marine litter in Lesvos island, are presented. Both phenomena have increasing interest among scientists monitoring sensitive coastal areas. This paper outlines the integration of UAS for data acquisition and Structure from Motion (SfM) pipeline for the visualization of selected coastal areas in the Aegean Sea. The followed UAS-SfM methodology produces very detailed orthophoto maps. This high resolution spatial information is used for mapping and detecting primarily, marine litter on coastal and underwater zones and secondly, coastline changes and coastal erosion. More specific the produced orthophoto maps analyzed through GIS and with the use of the appropriate cartographic techniques the objective environmental parameters were mapped. Results showed that UAS-SfM pipeline produces geoinformation with high accuracy and spatial resolution that helps scientists to map with confidence environmental changes that take place in shoreline zones.

Identifying Population Vulnerable to Extreme Heat Events in San Jose, California.

NASA Astrophysics Data System (ADS)

Rivera, A. L.

2016-12-01

The extreme heat days not only make cities less comfortable for living but also they are associated with increased morbidity and mortality. Mapping studies have demonstrated spatial variability in heat vulnerability. A study conducted between 2000 and 2011 in New York City shows that deaths during heat waves was more likely to occur in black individuals, at home in census tracts which received greater public assistance. This map project intends to portray areas in San Jose California that are vulnerable to extreme heat events. The variables considered to build a vulnerability index are: land surface temperature, vegetated areas (NDVI), and people exposed to these area (population density).

Shaded seafloor relief, backscatter strength, and surficial geology; German Bank, Scotian Shelf, offshore Nova Scotia

USGS Publications Warehouse

Todd, B.J.; Valentine, Page C.

2010-01-01

This map is part of a three-map series of German Bank, located on the Scotian Shelf off southern Nova Scotia.  This map is the product of a number of surveys (1997-2003) that used a multibeam sonar system to map 5321 km2 of the seafloor.  Other surveys collected geological data for scientific interpretation.  This map sheet shows the seafloor topography of German Bank in shaded-relief view and seafloor depth (coded by colour) at a scale of 1:1000,000.  Topographic contours generated from the multibeam data are shown (in white) on the colour-coded multibeam topography at a depth interval of 20 m.  Bathymetic contours (in blue) outside the multibeam survey area, presented at a depth interval of 10 m, are from the Natural Resource Map series (Canadian Hydrographic Service, 1967, 1971a, 1971b, 1972). Sheet 2 shows coloured backscatter strength in shaded-relief view.  Sheet 3 shows seafloor topography in shaded-relief view with colour-coded surficial geological units.

Altitude of the Top of the Madison Limestone in the Black Hills area, South Dakota, 1999

USGS Publications Warehouse

Carter, Janet M.; Redden, Jack A.

2000-01-01

This map is a product of the Black Hills Hydrology Study, which was initiated in 1990 to assess the quantity, quality, and distribution of surface water and groundwater in the Black Hills area of South Dakota (Driscoll, 1992). This long-term study is a cooperative effort between the U.S. Geological Survey (USGS), the South Dakota Department of Environment and Natural Resources, and the West Dakota Water Development District, which represents various local and county cooperators. This map is part of a series of 1:100,000-scale maps for the study. The maps include a hydrogeologic map, structure-contour maps (altitudes of the tops of formations) for five formations that contain major aquifers in the study area, and potentiometric maps for these five major aquifers (the Inyan Kara, Minnekahta, Minnelusa, Madison, and Deadwood aquifers).The study area consists of the topographically defined Black Hills and adjacent areas located in western South Dakota. The Black Hills area is an elongated, dome-shaped feature, about 125 miles long and 60 miles wide, which was uplifted during the Laramide orogeny (Feldman and Heimlich, 1980). The oldest geologic units in the study arca arc Precambrian metamorphic and igneous rocks, which are exposed in the central core of the Black Hills. Surrounding the Precambrian core is a layered series of sedimentary rocks including limestones, sandstones, and shales that are exposed in roughly concentric rings around the uplifted flanks of the Black Hills. The bedrock sedimentary units typically dip away from the uplifted Black Hills at angles that approach or exceed 10 degrees near the outcrops, and decrease with distance from the uplift. Many of the sedimentary units contain aquifers, both within and beyond the study area. Recharge to these aquifers occurs from infiltration of precipitation upon the outcrops and, in some cases, from infiltration of streamflow (Hortness and Driscoll, 1998). Artesian conditions generally exist within these aquifers where an upper confining layer is present. Flowing wells and artesian springs that originate from confined aquifers are common around the periphery of the Black Hills.The purpose of this map is to show the altitude of the top (structure contours) of the Madison Limestone within the area of the Black Hills Hydrology Study. The depth to the top of the Madison Limestone can be estimated at a specific site by subtracting the altitude of the top of the formation from the topographic elevation. However, caution is urged in determining the depth to the top of the formation in areas on the map where the contours are approximately located.

Active, capable, and potentially active faults - a paleoseismic perspective

USGS Publications Warehouse

Machette, M.N.

2000-01-01

Maps of faults (geologically defined source zones) may portray seismic hazards in a wide range of completeness depending on which types of faults are shown. Three fault terms - active, capable, and potential - are used in a variety of ways for different reasons or applications. Nevertheless, to be useful for seismic-hazards analysis, fault maps should encompass a time interval that includes several earthquake cycles. For example, if the common recurrence in an area is 20,000-50,000 years, then maps should include faults that are 50,000-100,000 years old (two to five typical earthquake cycles), thus allowing for temporal variability in slip rate and recurrence intervals. Conversely, in more active areas such as plate boundaries, maps showing faults that are <10,000 years old should include those with at least 2 to as many as 20 paleoearthquakes. For the International Lithosphere Programs' Task Group II-2 Project on Major Active Faults of the World our maps and database will show five age categories and four slip rate categories that allow one to select differing time spans and activity rates for seismic-hazard analysis depending on tectonic regime. The maps are accompanied by a database that describes evidence for Quaternary faulting, geomorphic expression, and paleoseismic parameters (slip rate, recurrence interval and time of most recent surface faulting). These maps and databases provide an inventory of faults that would be defined as active, capable, and potentially active for seismic-hazard assessments.

U.S. Geological Survey 2002 Petroleum Resource Assessment of the National Petroleum Reserve in Alaska (NPRA): GIS Play Maps

USGS Publications Warehouse

Garrity, Christopher P.; Houseknecht, David W.; Bird, Kenneth J.

2002-01-01

This report provides digital GIS files of maps for each of the 24 plays evaluated in the U.S. Geological Survey (USGS) 2002 petroleum resource assessment of the NPRA (Bird and Houseknecht, 2002a). These are the same maps released in pdf format by Bird and Houseknecht (2002b). The USGS released in 2002 a summary of the estimated volume of technically recoverable, undiscovered oil and nonassociated gas resources for 24 plays in NPRA (Bird and Houseknecht, 2002b). The NPRA assessment study area includes Federal and Native onshore land and adjacent State offshore areas. A map showing the areal extent of each play was prepared by USGS geologists as a preliminary step in the assessment process. Boundaries were drawn on the basis of a variety of information, including seismic reflection data, results of previous exploration drilling, and regional patterns of rock properties. Play boundary polygons were captured by digitizing the play maps prepared by USGS geologists. Federal, Native, and State areas were later clipped from the play boundary polygons, allowing for acreages to be calculated for entire plays and for various subareas within plays.

Multi-Hazard Vulnerability Assessment Along the Coast of Visakhapatnam, North-East Coast of India

NASA Astrophysics Data System (ADS)

Vivek, G.; Grinivasa Kumar, T.

2016-08-01

The current study area is coastal zone of Visakhapatnam, district of Andhra Pradesh along the coast of India. This area is mostly vulnerable to many disasters such as storms, cyclone, flood, tsunami and erosion. This area is considered as cyclone prone area because of frequently occurrence of the cyclones in this area. Recently the two tropical cyclones that formed in the Bay of Bengal are Hudhud (October 13, 2014) and Phylin (October 11, 2013), has caused devastating impacts on the eastern coast and shows that the country has lack of preparedness to cyclone, storm surge and related natural hazards. The multi-hazard vulnerability maps prepared here are a blended and combined overlay of multiple hazards those affecting the coastal zone. The present study aims to develop a methodology for coastal multi-hazard vulnerability assessment. This study carried out using parameters like probability of coastal slope, tsunami arrival height, future sea level rise, coastal erosion and tidal range. The multi-hazard vulnerability maps prepared by overlaying of multi hazards those affecting the coastal zone. Multi-hazard vulnerability maps further reproduced as risk maps with the land use information. The decision making tools presented here can provide a useful information during the disaster for the evacuation process and to evolve a management strategy.

Quantitative assessment of desertification in south of Iran using MEDALUS method.

PubMed

Sepehr, A; Hassanli, A M; Ekhtesasi, M R; Jamali, J B

2007-11-01

The main aim of this study was the quantitative assessment of desertification process in the case study area of the Fidoye-Garmosht plain (Southern Iran). Based on the MEDALUS approach and the characteristics of study area a regional model developed using GIS. Six main factors or indicators of desertification including: soil, climate, erosion, plant cover, groundwater and management were considered for evaluation. Then several sub-indicators affecting the quality of each main indicator were identified. Based on the MEDALUS approach, each sub-indicator was quantified according to its quality and given a weighting of between 1.0 and 2.0. ArcGIS 9 was used to analyze and prepare the layers of quality maps using the geometric mean to integrate the individual sub-indicator maps. In turn the geometric mean of all six quality maps was used to generate a single desertification status map. Results showed that 12% of the area is classified as very severe, 81% as severe and 7% as moderately affected by desertification. In addition the plant cover and groundwater indicators were the most important factors affecting desertification process in the study area. The model developed may be used to assess desertification process and distinguish the areas sensitive to desertification in the study region and in regions with the similar characteristics.

Identification of wild areas in southern lower Michigan. [terrain analysis from aerial photography, and satellite imagery

NASA Technical Reports Server (NTRS)

Habowski, S.; Cialek, C.

1978-01-01

An inventory methodology was developed to identify potential wild area sites. A list of site criteria were formulated and tested in six selected counties. Potential sites were initially identified from LANDSAT satellite imagery. A detailed study of the soil, vegetation and relief characteristics of each site based on both high-altitude aerial photographs and existing map data was conducted to eliminate unsuitable sites. Ground reconnaissance of the remaining wild areas was made to verify suitability and acquire information on wildlife and general aesthetics. Physical characteristics of the wild areas in each county are presented in tables. Maps show the potential sites to be set aside for natural preservation and regulation by the state under the Wilderness and Natural Areas Act of 1972.

Object-based Classification for Detecting Landslides and Stochastic Procedure to landslide susceptibility maps - A Case at Baolai Village, SW Taiwan

NASA Astrophysics Data System (ADS)

Lin, Ying-Tong; Chang, Kuo-Chen; Yang, Ci-Jian

2017-04-01

As the result of global warming in the past decades, Taiwan has experienced more and more extreme typhoons with hazardous massive landslides. In this study, we use object-oriented analysis method to classify landslide area at Baolai village by using Formosat-2 satellite images. We used for multiresolution segmented to generate the blocks, and used hierarchical logic to classified 5 different kinds of features. After that, classification the landslide into different type of landslide. Beside, we use stochastic procedure to integrate landslide susceptibility maps. This study assumed that in the extreme event, 2009 Typhoon Morakot, which precipitation goes to 1991.5mm in 5 days, and the highest landslide susceptible area. The results show that study area's landslide area was greatly changes, most of landslide was erosion by gully and made dip slope slide, or erosion by the stream, especially at undercut bank. From the landslide susceptibility maps, we know that the old landslide area have high potential to occur landslides in the extreme event. This study demonstrates the changing of landslide area and the landslide susceptible area. Keywords: Formosat-2, object-oriented, segmentation, classification, landslide, Baolai Village, SW Taiwan, FS

Surveying the area of deforestation of the Amazon by LANDSAT satellite imagery. [Mato grosso, Goias and Para, Brazil

NASA Technical Reports Server (NTRS)

Dejesusparada, N. (Principal Investigator); Tardin, A. T.; Dossantos, A. P.; Lee, D. C. L.; Soaresmaia, F. C.; Mendonca, F. J.; Assuncao, G. V.; Rodrigues, J. E.; Demouraabdon, M.; Novaes, R. A.

1979-01-01

LANDSAT imagery was used to determine the amount of deforestation in a study area comprising 55 million hectares of the Amazon region. Results show that more than 4 million hectares were deforested. Maps and pictures of the deforested area in relation to the total area of the Amazon are included.

Probabilistic mapping of flood-induced backscatter changes in SAR time series

NASA Astrophysics Data System (ADS)

Schlaffer, Stefan; Chini, Marco; Giustarini, Laura; Matgen, Patrick

2017-04-01

The information content of flood extent maps can be increased considerably by including information on the uncertainty of the flood area delineation. This additional information can be of benefit in flood forecasting and monitoring. Furthermore, flood probability maps can be converted to binary maps showing flooded and non-flooded areas by applying a threshold probability value pF = 0.5. In this study, a probabilistic change detection approach for flood mapping based on synthetic aperture radar (SAR) time series is proposed. For this purpose, conditional probability density functions (PDFs) for land and open water surfaces were estimated from ENVISAT ASAR Wide Swath (WS) time series containing >600 images using a reference mask of permanent water bodies. A pixel-wise harmonic model was used to account for seasonality in backscatter from land areas caused by soil moisture and vegetation dynamics. The approach was evaluated for a large-scale flood event along the River Severn, United Kingdom. The retrieved flood probability maps were compared to a reference flood mask derived from high-resolution aerial imagery by means of reliability diagrams. The obtained performance measures indicate both high reliability and confidence although there was a slight under-estimation of the flood extent, which may in part be attributed to topographically induced radar shadows along the edges of the floodplain. Furthermore, the results highlight the importance of local incidence angle for the separability between flooded and non-flooded areas as specular reflection properties of open water surfaces increase with a more oblique viewing geometry.

An interpretation of the 1996 aeromagnetic data for the Santa Cruz basin, Tumacacori Mountains, Santa Rita Mountains, and Patagonia Mountains, south-central Arizona

USGS Publications Warehouse

Gettings, Mark E.

2002-01-01

High resolution aeromagnetic survey data flown at 250 m above the terrain and 250 m line spacing over the Santa Cruz Valley and the surrounding Tumacacori, Patagonia, and Santa Rita Mountains has been interpreted by correlation of the magnetic anomaly field and various derivative maps with geologic maps. Measurements of in-situ magnetic properties of several of the map units determined whether or not mapped lithologies were responsible for observed anomalies. Correlation of the magnetic anomaly field with mapped geology shows that numerous map units of volcanic and intrusive rocks from Jurassic Middle Tertiary in age are reversely polarized, some of which have not been previously reported. Trends derived from the magnetic anomaly data correlate closely with structures from major tectonic events in the geologic history of the area including Triassic-Jurassic crustal accretion and magmatism, Laramide magmatism and tectonism, northeast-southwest Mid-Tertiary extension, and east-west Basin and Range extension. Application of two textural measures to the magnetic anomaly data, number of peaks and troughs per km (a measure of roughness) and Euclidean length per km (a measure of amplitude), delineated areas of consistent magnetic anomaly texture. These measures were successful at the delineation of areas of consistent magnetic lithology both on the surface and in the subsurface beneath basin fill. Several areas of basement prospective for mineral resources beneath basin fill were identified.

Terrestrial Sediments of the Earth: Development of a Global Unconsolidated Sediments Map Database (GUM)

NASA Astrophysics Data System (ADS)

Börker, J.; Hartmann, J.; Amann, T.; Romero-Mujalli, G.

2018-04-01

Mapped unconsolidated sediments cover half of the global land surface. They are of considerable importance for many Earth surface processes like weathering, hydrological fluxes or biogeochemical cycles. Ignoring their characteristics or spatial extent may lead to misinterpretations in Earth System studies. Therefore, a new Global Unconsolidated Sediments Map database (GUM) was compiled, using regional maps specifically representing unconsolidated and quaternary sediments. The new GUM database provides insights into the regional distribution of unconsolidated sediments and their properties. The GUM comprises 911,551 polygons and describes not only sediment types and subtypes, but also parameters like grain size, mineralogy, age and thickness where available. Previous global lithological maps or databases lacked detail for reported unconsolidated sediment areas or missed large areas, and reported a global coverage of 25 to 30%, considering the ice-free land area. Here, alluvial sediments cover about 23% of the mapped total ice-free area, followed by aeolian sediments (˜21%), glacial sediments (˜20%), and colluvial sediments (˜16%). A specific focus during the creation of the database was on the distribution of loess deposits, since loess is highly reactive and relevant to understand geochemical cycles related to dust deposition and weathering processes. An additional layer compiling pyroclastic sediment is added, which merges consolidated and unconsolidated pyroclastic sediments. The compilation shows latitudinal abundances of sediment types related to climate of the past. The GUM database is available at the PANGAEA database (https://doi.org/10.1594/PANGAEA.884822).

Probability mapping of scarred myocardium using texture and intensity features in CMR images

PubMed Central

2013-01-01

Background The myocardium exhibits heterogeneous nature due to scarring after Myocardial Infarction (MI). In Cardiac Magnetic Resonance (CMR) imaging, Late Gadolinium (LG) contrast agent enhances the intensity of scarred area in the myocardium. Methods In this paper, we propose a probability mapping technique using Texture and Intensity features to describe heterogeneous nature of the scarred myocardium in Cardiac Magnetic Resonance (CMR) images after Myocardial Infarction (MI). Scarred tissue and non-scarred tissue are represented with high and low probabilities, respectively. Intermediate values possibly indicate areas where the scarred and healthy tissues are interwoven. The probability map of scarred myocardium is calculated by using a probability function based on Bayes rule. Any set of features can be used in the probability function. Results In the present study, we demonstrate the use of two different types of features. One is based on the mean intensity of pixel and the other on underlying texture information of the scarred and non-scarred myocardium. Examples of probability maps computed using the mean intensity of pixel and the underlying texture information are presented. We hypothesize that the probability mapping of myocardium offers alternate visualization, possibly showing the details with physiological significance difficult to detect visually in the original CMR image. Conclusion The probability mapping obtained from the two features provides a way to define different cardiac segments which offer a way to identify areas in the myocardium of diagnostic importance (like core and border areas in scarred myocardium). PMID:24053280

Implementing automatic LiDAR and supervised mapping methodologies to quantify agricultural terraced landforms at landscape scale: the case of Veneto Region

NASA Astrophysics Data System (ADS)

Eugenio Pappalardo, Salvatore; Ferrarese, Francesco; Tarolli, Paolo; Varotto, Mauro

2016-04-01

Traditional agricultural terraced landscapes presently embody an important cultural value to be deeply investigated, both for their role in local heritage and cultural economy and for their potential geo-hydrological hazard due to abandonment and degradation. Moreover, traditional terraced landscapes are usually based on non-intensive agro-systems and may enhance some important ecosystems services such as agro-biodiversity conservation and cultural services. Due to their unplanned genesis, mapping, quantifying and classifying agricultural terraces at regional scale is often critical as far as they are usually set up on geomorphologically and historically complex landscapes. Hence, traditional mapping methods are generally based on scientific literature and local documentation, historical and cadastral sources, technical cartography and aerial images visual interpretation or, finally, field surveys. By this, limitations and uncertainty in mapping at regional scale are basically related to forest cover and lack in thematic cartography. The Veneto Region (NE of Italy) presents a wide heterogeneity of agricultural terraced landscapes, mainly distributed within the hilly and Prealps areas. Previous studies performed by traditional mapping method quantified 2,688 ha of terraced areas, showing the higher values within the Prealps of Lessinia (1,013 ha, within the Province of Verona) and in the Brenta Valley (421 ha, within the Province of Vicenza); however, terraced features of these case studies show relevant differences in terms of fragmentation and intensity of terraces, highlighting dissimilar degrees of clusterization: 1.7 ha on one hand (Province of Verona) and 1.2 ha per terraced area (Province of Vicenza) on the other one. The aim of this paper is to implement and to compare automatic methodologies with traditional survey methodologies to map and assess agricultural terraces in two representative areas of the Veneto Region. Testing different Remote Sensing analyses such as LiDAR topography survey and visual interpretation from aerial orthophotos (RGB+NIR bands) we performed a territorial analysis in the Lessinia and Brenta Valley case studies. Preliminary results show that terraced feature extraction by automatic LiDAR survey is more efficient both in identifying geometries (walls and terraced surfaces) and in quantifying features under the forest canopy; however, traditional mapping methodology confirms its strength by matching different methods and different data such as aerial photo, visual interpretation, maps and field surveys. Hence, the two methods here compared represent a cross-validation and let us to better know the complexity of this kind of landscape.

Operational monitoring of land-cover change using multitemporal remote sensing data

NASA Astrophysics Data System (ADS)

Rogan, John

2005-11-01

Land-cover change, manifested as either land-cover modification and/or conversion, can occur at all spatial scales, and changes at local scales can have profound, cumulative impacts at broader scales. The implication of operational land-cover monitoring is that researchers have access to a continuous stream of remote sensing data, with the long term goal of providing for consistent and repetitive mapping. Effective large area monitoring of land-cover (i.e., >1000 km2) can only be accomplished by using remotely sensed images as an indirect data source in land-cover change mapping and as a source for land-cover change model projections. Large area monitoring programs face several challenges: (1) choice of appropriate classification scheme/map legend over large, topographically and phenologically diverse areas; (2) issues concerning data consistency and map accuracy (i.e., calibration and validation); (3) very large data volumes; (4) time consuming data processing and interpretation. Therefore, this dissertation research broadly addresses these challenges in the context of examining state-of-the-art image pre-processing, spectral enhancement, classification, and accuracy assessment techniques to assist the California Land-cover Mapping and Monitoring Program (LCMMP). The results of this dissertation revealed that spatially varying haze can be effectively corrected from Landsat data for the purposes of change detection. The Multitemporal Spectral Mixture Analysis (MSMA) spectral enhancement technique produced more accurate land-cover maps than those derived from the Multitemporal Kauth Thomas (MKT) transformation in northern and southern California study areas. A comparison of machine learning classifiers showed that Fuzzy ARTMAP outperformed two classification tree algorithms, based on map accuracy and algorithm robustness. Variation in spatial data error (positional and thematic) was explored in relation to environmental variables using geostatistical interpolation techniques. Finally, the land-cover modification maps generated for three time intervals (1985--1990--1996--2000), with nine change-classes revealed important variations in land-cover gain and loss between northern and southern California study areas.

Maps showing aeromagnetic data and interpretation for the Kalmiopsis Wilderness, southwestern Oregon

USGS Publications Warehouse

Blakely, Richard J.; Page, Norman J; Gray, Floyd; Senior, Lisa; Ryan, Holly F.

1983-01-01

Most individual anomalies in this area are caused by known geologic boundaries or topographic features; those that are not are of particular interest because they may reflect areas of increased or decreased magnetization associated with zones of minerlization. 

Mapping urban climate zones and quantifying climate behaviors--an application on Toulouse urban area (France).

PubMed

Houet, Thomas; Pigeon, Grégoire

2011-01-01

Facing the concern of the population to its environment and to climatic change, city planners are now considering the urban climate in their choices of planning. The use of climatic maps, such Urban Climate Zone‑UCZ, is adapted for this kind of application. The objective of this paper is to demonstrate that the UCZ classification, integrated in the World Meteorological Organization guidelines, first can be automatically determined for sample areas and second is meaningful according to climatic variables. The analysis presented is applied on Toulouse urban area (France). Results show first that UCZ differentiate according to air and surface temperature. It has been possible to determine the membership of sample areas to an UCZ using landscape descriptors automatically computed with GIS and remote sensed data. It also emphasizes that climate behavior and magnitude of UCZ may vary from winter to summer. Finally we discuss the influence of climate data and scale of observation on UCZ mapping and climate characterization. Copyright © 2011 Elsevier Ltd. All rights reserved.

Coherence area profiling in multi-spatial-mode squeezed states

DOE PAGES

Lawrie, Benjamin J.; Pooser, Raphael C.; Otterstrom, Nils T.

2015-09-12

The presence of multiple bipartite entangled modes in squeezed states generated by four-wave mixing enables ultra-trace sensing, imaging, and metrology applications that are impossible to achieve with single-spatial-mode squeezed states. For Gaussian seed beams, the spatial distribution of these bipartite entangled modes, or coherence areas, across each beam is largely dependent on the spatial modes present in the pump beam, but it has proven difficult to map the distribution of these coherence areas in frequency and space. We demonstrate an accessible method to map the distribution of the coherence areas within these twin beams. In addition, we also show thatmore » the pump shape can impart different noise properties to each coherence area, and that it is possible to select and detect coherence areas with optimal squeezing with this approach.« less

Digital geologic map database of the Nevada Test Site area, Nevada

USGS Publications Warehouse

Wahl, R.R.; Sawyer, D.A.; Minor, S.A.; Carr, M.D.; Cole, J.C.; Swadley, W.C.; Laczniak, R.J.; Warren, R.G.; Green, K.S.; Engle, C.M.

1997-01-01

Forty years of geologic investigations at the Nevada Test Site (NTS) have been digitized. These data include all geologic information that: (1) has been collected, and (2) can be represented on a map within the map borders at the map scale is included in the map digital coverages. The following coverages are included with this dataset: Coverage Type Description geolpoly Polygon Geologic outcrops geolflts line Fault traces geolatts Point Bedding attitudes, etc. geolcald line Caldera boundaries geollins line Interpreted lineaments geolmeta line Metamorphic gradients The above coverages are attributed with numeric values and interpreted information. The entity files documented below show the data associated with each coverage.

Finding Your Way with Map and Compass

USGS Publications Warehouse

,

2001-01-01

A topographic map tells you where things are and how to get to them, whether you're hiking, biking, hunting, fishing, or just interested in the world around you. These maps describe the shape of the land. They define and locate natural and manmade features like woodlands, waterways, important buildings, and bridges. They show the distance between any two places, and they also show the direction from one point to another. Distances and directions take a bit of figuring, but the topography and features of the land are easy to determine. The topography is shown by contours. These are imaginary lines that follow the ground surface at a constant elevation; they are usually printed in brown, in two thicknesses. The heavier lines are called index contours, and they are usually marked with numbers that give the height in feet or meters. The contour interval, a set difference in elevation between the brown lines, varies from map to map; its value is given in the margin of each map. Contour lines that are close together represent steep slopes. Natural and manmade features are represented by colored areas and by a set of standard symbols on all U.S. Geological Survey (USGS) topographic maps. Woodlands, for instance, are shown in a green tint; waterways, in blue. Buildings may be shown on the map as black squares or outlines. Recent changes in an area may be shown by a purple overprint. A road may be printed in red or black solid or dashed lines, depending on its size and surface. A list of symbols is available from the Earth Science Information Center (ESIC).

Soil erosion assessment using the Universal Soil Loss Equation (USLE) in a GIS framework: A case study of Zacatecas, México

NASA Astrophysics Data System (ADS)

Betanzos Arroyo, L. I.; Prol Ledesma, R. M.; da Silva Pinto da Rocha, F. J. P.

2014-12-01

The Universal Soil Loss Equation (USLE), which is considered to be a contemporary approach in soil loss assessment, was used to assess soil erosion hazard in the Zacatecas mining district. The purpose of this study is to produce erosion susceptibility maps for an area that is polluted with mining tailings which are susceptible to erosion and can disperse the particles that contain heavy metals and other toxic elements. USLE method is based in the estimation of soil loss per unit area and takes into account specific parameters such as precipitation data, topography, soil erodibility, erosivity and runoff. The R-factor (rainfall erosivity) was calculated from monthly and annual precipitation data. The K-factor (soil erodibility) was estimated using soil maps available from the CONABIO at a scale of 1:250000. The LS-factor (slope length and steepness) was determined from a 30-m digital elevation model. A raster-based Geographic Information System (GIS) was used to interactively calculate soil loss and map erosion hazard. The results show that estimated erosion rates ranged from 0 to 4770.48 t/ha year. Maximum proportion of the total area of the Zacatecas mining district have nil to very extremely slight erosion severity. Small areas in the central and south part of the study area shows the critical condition requiring sustainable land management.

Suitability aero-geophysical methods for generating conceptual soil maps and their use in the modeling of process-related susceptibility maps

NASA Astrophysics Data System (ADS)

Tilch, Nils; Römer, Alexander; Jochum, Birgit; Schattauer, Ingrid

2014-05-01

In the past years, several times large-scale disasters occurred in Austria, which were characterized not only by flooding, but also by numerous shallow landslides and debris flows. Therefore, for the purpose of risk prevention, national and regional authorities also require more objective and realistic maps with information about spatially variable susceptibility of the geosphere for hazard-relevant gravitational mass movements. There are many and various proven methods and models (e.g. neural networks, logistic regression, heuristic methods) available to create such process-related (e.g. flat gravitational mass movements in soil) suszeptibility maps. But numerous national and international studies show a dependence of the suitability of a method on the quality of process data and parameter maps (f.e. Tilch & Schwarz 2011, Schwarz & Tilch 2011). In this case, it is important that also maps with detailed and process-oriented information on the process-relevant geosphere will be considered. One major disadvantage is that only occasionally area-wide process-relevant information exists. Similarly, in Austria often only soil maps for treeless areas are available. However, in almost all previous studies, randomly existing geological and geotechnical maps were used, which often have been specially adapted to the issues and objectives. This is one reason why very often conceptual soil maps must be derived from geological maps with only hard rock information, which often have a rather low quality. Based on these maps, for example, adjacent areas of different geological composition and process-relevant physical properties are razor sharp delineated, which in nature appears quite rarly. In order to obtain more realistic information about the spatial variability of the process-relevant geosphere (soil cover) and its physical properties, aerogeophysical measurements (electromagnetic, radiometric), carried out by helicopter, from different regions of Austria were interpreted. Previous studies show that, especially with radiometric measurements, the two-dimensional spatial variability of the nature of the process-relevant soil, close to the surface can be determined. In addition, the electromagnetic measurements are more important to obtain three-dimensional information of the deeper geological conditions and to improve the area-specific geological knowledge and understanding. The validation of these measurements is done with terrestrial geoelectrical measurements. So both aspects, radiometric and electromagnetic measurements, are important and subsequently, interpretation of the geophysical results can be used as the parameter maps in the modeling of more realistic susceptibility maps with respect to various processes. Within this presentation, results of geophysical measurements, the outcome and the derived parameter maps, as well as first process-oriented susceptibility maps in terms of gravitational soil mass movements will be presented. As an example results which were obtained with a heuristic method in an area in Vorarlberg (Western Austria) will be shown. References: Schwarz, L. & Tilch, N. (2011): Why are good process data so important for the modelling of landslide susceptibility maps?- EGU-Postersession "Landslide hazard and risk assessment, and landslide management" (NH 3.6), Vienna. [http://www.geologie.ac.at/fileadmin/user_upload/dokumente/pdf/poster/poster_2011_egu_schwarz_tilch_1.pdf] Tilch, N. & Schwarz, L. (2011): Spatial and scale-dependent variability in data quality and their influence on susceptibility maps for gravitational mass movements in soil, modelled by heuristic method.- EGU-Postersession "Landslide hazard and risk assessment, and landslide management" (NH 3.6); Vienna. [http://www.geologie.ac.at/fileadmin/user_upload/dokumente/pdf/poster/poster_2011_egu_tilch_schwarz.pdf

Remote Sensing for Hydrology: Surface Water Dynamics from Three Decades of Landsat Data

NASA Astrophysics Data System (ADS)

Tulbure, M. G.; Broich, M.; Kingsford, R.; Lucas, R.; Keith, D.

2014-12-01

Surface water is a vital resource affected by changes in climate and anthropogenic factors. Knowledge of surface water dynamics provides critical information for flood and drought management. Here we focused on the on the entire Murray-Darling Basin (MDB) of Australia, a large semi-arid region with scarce water resources, high hydroclimatic variability and competing water demands, impacted by climate change, altered flow regimes and land use changes. The MDB is also an area where substantial investment in environmental water allocation of large volumes of environmental flow was made. We used Landsat TM and ETM+ time series to synoptically map the dynamic of surface water extent with an internally consistent algorithm (Tulbure and Broich, 2013) over decades (1986-2011). We used a subset of Landsat path/rows for image training in both wet and dry years. Results show high interannual variability in number and size of flooded areas, with flooded areas during the Millennium Drought (until 2009) being substantially smaller than during the excessive 2010-2011 La Nina flooding. Flooding frequency in 2006, a very dry year was lower than in 2010, the La Nina year when extensive floods occurred. More developed areas of the basin showed different inter-annual patterns from natural areas of the basin. At Barmah-Millewa, the largest river red gum forest in the world, we also mapped flooded forest and tracked changes in NDVI. Higher NDVI values were found in areas more frequently flooded. Knowledge of the spatial and temporal dynamics of flooding and the response of riparian vegetation communities to flooding is important for management of floodplain wetlands and vegetation communities and for investigating effectiveness of environmental flows and flow regimes in the MDB. Existing maps of inundated areas are linked with river flow to quantify the relationship between river flow and inundated area in the MDB. Historic flood inundation extent mapped via remote sensing can be used to quantify spatially explicit changes in surface water dynamics and vegetation communities as outcomes of management scenarios in response to water management decisions. This methodology is globally applicable and relevant to areas prone to flooding with competing water demands and can be used for mapping water availability in data scarce regions.

Using a binary logistic regression method and GIS for evaluating and mapping the groundwater spring potential in the Sultan Mountains (Aksehir, Turkey)

NASA Astrophysics Data System (ADS)

Ozdemir, Adnan

2011-07-01

SummaryThe purpose of this study is to produce a groundwater spring potential map of the Sultan Mountains in central Turkey, based on a logistic regression method within a Geographic Information System (GIS) environment. Using field surveys, the locations of the springs (440 springs) were determined in the study area. In this study, 17 spring-related factors were used in the analysis: geology, relative permeability, land use/land cover, precipitation, elevation, slope, aspect, total curvature, plan curvature, profile curvature, wetness index, stream power index, sediment transport capacity index, distance to drainage, distance to fault, drainage density, and fault density map. The coefficients of the predictor variables were estimated using binary logistic regression analysis and were used to calculate the groundwater spring potential for the entire study area. The accuracy of the final spring potential map was evaluated based on the observed springs. The accuracy of the model was evaluated by calculating the relative operating characteristics. The area value of the relative operating characteristic curve model was found to be 0.82. These results indicate that the model is a good estimator of the spring potential in the study area. The spring potential map shows that the areas of very low, low, moderate and high groundwater spring potential classes are 105.586 km 2 (28.99%), 74.271 km 2 (19.906%), 101.203 km 2 (27.14%), and 90.05 km 2 (24.671%), respectively. The interpretations of the potential map showed that stream power index, relative permeability of lithologies, geology, elevation, aspect, wetness index, plan curvature, and drainage density play major roles in spring occurrence and distribution in the Sultan Mountains. The logistic regression approach has not yet been used to delineate groundwater potential zones. In this study, the logistic regression method was used to locate potential zones for groundwater springs in the Sultan Mountains. The evolved model was found to be in strong agreement with the available groundwater spring test data. Hence, this method can be used routinely in groundwater exploration under favourable conditions.

Glacier Surface Lowering and Stagnation in the Manaslu Region of Nepal

NASA Astrophysics Data System (ADS)

Robson, B. A.; Nuth, C.; Nielsen, P. R.; Hendrickx, M.; Dahl, S. O.

2015-12-01

Frequent and up-to-date glacier outlines are needed for many applications of glaciology, not only glacier area change analysis, but also for masks in volume or velocity analysis, for the estimation of water resources and as model input data. Remote sensing offers a good option for creating glacier outlines over large areas, but manual correction is frequently necessary, especially in areas containing supraglacial debris. We show three different workflows for mapping clean ice and debris-covered ice within Object Based Image Analysis (OBIA). By working at the object level as opposed to the pixel level, OBIA facilitates using contextual, spatial and hierarchical information when assigning classes, and additionally permits the handling of multiple data sources. Our first example shows mapping debris-covered ice in the Manaslu Himalaya, Nepal. SAR Coherence data is used in combination with optical and topographic data to classify debris-covered ice, obtaining an accuracy of 91%. Our second example shows using a high-resolution LiDAR derived DEM over the Hohe Tauern National Park in Austria. Breaks in surface morphology are used in creating image objects; debris-covered ice is then classified using a combination of spectral, thermal and topographic properties. Lastly, we show a completely automated workflow for mapping glacier ice in Norway. The NDSI and NIR/SWIR band ratio are used to map clean ice over the entire country but the thresholds are calculated automatically based on a histogram of each image subset. This means that in theory any Landsat scene can be inputted and the clean ice can be automatically extracted. Debris-covered ice can be included semi-automatically using contextual and morphological information.

Molecular imaging of cannabis leaf tissue with MeV-SIMS method

NASA Astrophysics Data System (ADS)

Jenčič, Boštjan; Jeromel, Luka; Ogrinc Potočnik, Nina; Vogel-Mikuš, Katarina; Kovačec, Eva; Regvar, Marjana; Siketić, Zdravko; Vavpetič, Primož; Rupnik, Zdravko; Bučar, Klemen; Kelemen, Mitja; Kovač, Janez; Pelicon, Primož

2016-03-01

To broaden our analytical capabilities with molecular imaging in addition to the existing elemental imaging with micro-PIXE, a linear Time-Of-Flight mass spectrometer for MeV Secondary Ion Mass Spectrometry (MeV-SIMS) was constructed and added to the existing nuclear microprobe at the Jožef Stefan Institute. We measured absolute molecular yields and damage cross-section of reference materials, without significant alteration of the fragile biological samples during the duration of measurements in the mapping mode. We explored the analytical capability of the MeV-SIMS technique for chemical mapping of the plant tissue of medicinal cannabis leaves. A series of hand-cut plant tissue slices were prepared by standard shock-freezing and freeze-drying protocol and deposited on the Si wafer. We show the measured MeV-SIMS spectra showing a series of peaks in the mass area of cannabinoids, as well as their corresponding maps. The indicated molecular distributions at masses of 345.5 u and 359.4 u may be attributed to the protonated THCA and THCA-C4 acids, and show enhancement in the areas with opened trichome morphology.

Map showing general availability of ground water in the Kaiparowits coal-basin area, Utah

USGS Publications Warehouse

Price, Don

1977-01-01

This is one of a series of maps that describe the geology and related natural resources in the Kaiparowits coal-basin area. This map is based partly on records of water wells, springs, and coal and petroleum exploration holes, partly on unpublished reports of field evaluations of prospective stock-water well sites by personnel of the U.S. Geological Survey, and partly on a 6-day field reconnaissance by the writer in parts of the mapped area.Most of the data used to compile this map were collected by the U.S. Geological Survey in cooperation with State, local, and other Federal agencies. Published sources of data included Phoenix (1963), Iorns, Hembree, and Phoenix (1964), Cooley (1965), Feltis (1966), Goode (1966, 1969), and the final environmental impact statement for the proposed Kaiparowits power project (U.S. Bureau of Land Management, 1976).Few data about the availability or depth of ground water could be obtained for large areas in the Kaiparowits coal basin. In those areas, expected yields of individual wells are inferred from the geology as compiled by Stokes (1964) and Hackman and Wyant (1973), and depths of ground water in wells are inferred largely from the local topography.El Paso Natural Gas Co., Resources Co., Kaiser Engineers, and Southern California Edison Co. provided specific information regarding the availability and depth of ground water in their exploratory holes on the Kaiparowits Plateau. The cooperation of those firms is gratefully acknowledged.

Integrating aeromagnetic and Landsat™ 8 data into subsurface structural mapping of Precambrian basement complex

NASA Astrophysics Data System (ADS)

Kayode, John Stephen; Nawawi, M. N. M.; Abdullah, Khiruddin B.; Khalil, Amin E.

2017-01-01

The integration of Aeromagnetic data and remotely sensed imagery with the intents of mapping the subsurface geological structures in part of the South-western basement complex of Nigeria was developed using the PCI Geomatica Software. 2013. The data obtained from the Nigerian Geological Survey Agency; was corrected using Regional Residual Separation of the Total Magnetic field anomalies enhanced, and International Geomagnetic Reference Field removed. The principal objective of this study is, therefore, to introduce a rapid and efficient method of subsurface structural depth estimate and structural index evaluation through the incorporation of the Euler Deconvolution technique into PCI Geomatica 2013 to prospect for subsurface geological structures. The shape and depth of burial helped to define these structures from the regional aeromagnetic map. The method enabled various structural indices to be automatically delineated for an index of between 0.5 SI and 3.0 SI at a maximum depth of 1.1 km that clearly showed the best depths estimate for all the structural indices. The results delineate two major magnetic belts in the area; the first belt shows an elongated ridge-like structure trending mostly along the NorthNortheast-SouthSouthwest and the other anomalies trends primarily in the Northeast, Northwest, Northeast-Southwest parts of the study area that could be attributed to basement complex granitic intrusions from the tectonic history of the area. The majority of the second structures showed various linear structures different from the first structure. Basically, a significant offset was delineated at the core segment of the study area, suggesting a major subsurface geological feature that controls mineralisation in this area.

Geologic framework for the national assessment of carbon dioxide storage resources: Williston Basin, Central Montana Basins, and Montana Thrust Belt study areas: Chapter J in Geologic framework for the national assessment of carbon dioxide storage resources

USGS Publications Warehouse

Buursink, Marc L.; Merrill, Matthew D.; Craddock, William H.; Roberts-Ashby, Tina L.; Brennan, Sean T.; Blondes, Madalyn S.; Freeman, P.A.; Cahan, Steven M.; DeVera, Christina A.; Lohr, Celeste D.; Warwick, Peter D.; Corum, Margo D.

2014-01-01

Figures in this report show the study area boundaries along with the SAU extent and cell maps of well penetrations through sealing units into the top of the storage formations. The USGS does not necessarily know the location of all wells and cannot guarantee the full extent of drilling through specific formations in any given cell shown on the cell maps.

Potentiometric surface map of the Magothy aquifer in southern Maryland, September, 2003

USGS Publications Warehouse

Curtin, Stephen E.; Andreasen, David C.; Wheeler, Judith C.

2005-01-01

This report presents a map showing the potentiometric surface of the Magothy aquifer in the Magothy Formation of Upper Cretaceous age in Southern Maryland during September 2002. The map is based on water-level measurements in 79 wells. The highest measured water level was 83 feet above sea level near the northern boundary and outcrop area of the aquifer in the north-central part of Anne Arundel County. The potentiometric surface declined towards the south and east. Local gradients were directed toward the centers of two cones of depression that developed in response to pumping. These cones of depression were centered around well fields in the Waldorf area and at the Chalk Point power plant. Measured ground-water levels were as low as 81 feet below sea level in the Waldorf area and 75 feet below sea level at Chalk Point.

Teton Dam flood of June 1976, Firth quadrangle, Idaho

USGS Publications Warehouse

Hubbard, Larry L.; Bartells, John H.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Firth quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, Rose quadrangle, Idaho

USGS Publications Warehouse

Bartells, John H.; Hubbard, Larry L.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Rose quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, Rexburg quadrangle, Idaho

USGS Publications Warehouse

Harenberg, W.A.; Bigelow, B.B.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification on these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Rexburg quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, Deer Parks quadrangle, Idaho

USGS Publications Warehouse

Ray, Herman A.; Bennett, C. Michael; Records, Andrew W.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Deer Parks quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, Parker quadrangle, Idaho

USGS Publications Warehouse

Thomas, Cecil Albert; Ray, Herman A.

1976-01-01

The failure of Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls, Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Parker quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, St. Anthony quadrangle, Idaho

USGS Publications Warehouse

Thomas, Cecil A.; Ray, Herman A.; Matthai, Howard F.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the St. Anthony quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, Woodville quadrangle, Idaho

USGS Publications Warehouse

Matthai, Howard F.; Ray, Herman A.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Woodville quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, Menan Buttes quadrangle, Idaho

USGS Publications Warehouse

Thomas, Cecil A.; Ray, Herman A.; Harenberg, William A.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Menan Buttes quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, Idaho Falls South quadrangle, Idaho

USGS Publications Warehouse

Ray, Herman A.; Matthai, Howard F.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Idaho Falls South quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, Lewisville quadrangle, Idaho

USGS Publications Warehouse

Ray, Herman A.; Bigelow, Bruce B.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Lewisville quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, Idaho Falls North quadrangle, Idaho

USGS Publications Warehouse

Ray, Herman A.; Matthai, Howard F.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Idaho Falls North quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, Pingree quadrangle, Idaho

USGS Publications Warehouse

Hubbard, Larry L.; Bartells, John H.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Pingree quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, Blackfoot quadrangle, Idaho

USGS Publications Warehouse

Bartells, J.H.; Hubbard, Larry L.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Blackfoot quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, Rigby quadrangle, Idaho

USGS Publications Warehouse

Ray, Herman A.; Bigelow, Bruce B.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Rigby quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, Newdale quadrangle, Idaho

USGS Publications Warehouse

Ray, Herman A.; Matthai, Howard F.; Thomas, Cecil A.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Newdale quadrangle. (Woodard-USGS)

Teton Dam flood of June 1976, Moody quadrangle, Idaho

USGS Publications Warehouse

Harenberg, William A.; Bigelow, Bruce B.

1976-01-01

The failure of the Teton Dam caused extreme flooding along the Teton River, Henrys Fork, and Snake River in southeastern Idaho on June 5-8, 1976. No flooding occurred downstream from American Falls Reservoir. The inundated areas and maximum water-surface elevations are shown in a series of 17 hydrologic atlases. The area covered by the atlases extends from Teton Dam downstream to American Falls Reservoir, a distance of 100 miles. The extent of flooding shown on the maps was obtained by field inspections and aerial photographs made during and immediately after the flood. There may be small isolated areas within the boundaries shown that were not flooded, but the identification of these sites was beyond the scope of the study. The elevation data shown are mean-sea-level elevations of high-water marks identified in the field. This particular map (in the 17-map series) shows conditions in the Moody quadrangle. (Woodard-USGS)

Earthquake hazard assessment in the Zagros Orogenic Belt of Iran using a fuzzy rule-based model

NASA Astrophysics Data System (ADS)

Farahi Ghasre Aboonasr, Sedigheh; Zamani, Ahmad; Razavipour, Fatemeh; Boostani, Reza

2017-08-01

Producing accurate seismic hazard map and predicting hazardous areas is necessary for risk mitigation strategies. In this paper, a fuzzy logic inference system is utilized to estimate the earthquake potential and seismic zoning of Zagros Orogenic Belt. In addition to the interpretability, fuzzy predictors can capture both nonlinearity and chaotic behavior of data, where the number of data is limited. In this paper, earthquake pattern in the Zagros has been assessed for the intervals of 10 and 50 years using fuzzy rule-based model. The Molchan statistical procedure has been used to show that our forecasting model is reliable. The earthquake hazard maps for this area reveal some remarkable features that cannot be observed on the conventional maps. Regarding our achievements, some areas in the southern (Bandar Abbas), southwestern (Bandar Kangan) and western (Kermanshah) parts of Iran display high earthquake severity even though they are geographically far apart.

Summary appraisal of water resources in the Redmond Quadrangle, Sanpete and Sevier counties, Utah

USGS Publications Warehouse

Price, Don

1981-01-01

This map was compiled in conjunction with an energy-related geologic-mapping project on the Redmond Quadrangle (Witkind, 1980) in order to show the general availability and chemical quality of water in the area. The map is based chiefly on data collected by the U.S. Geological Survey under a continuing cooperative program with the Utah Department of Natural Resources, Division of Water Rights, and on cursory field observations by the writer. Most of the existing fata are in reports of Carpenter and Young (1963), Hahl and Cabell (1965), Young and Carpenter (1965) and Hahl and Mundorff (1968). Additional information about water and related land resources in the map area may be found in a report of the U.S. Department of Agriculture (1969).The map is intended for general planning purposes only and needs to be used with discretion. Detailed site-specific information about the availability and quality of water or about water-related problems can be gained only by special on-site investigations.

A large-scale extinction map of the Galactic Anticentre from 2MASS

NASA Astrophysics Data System (ADS)

Froebrich, D.; Murphy, G. C.; Smith, M. D.; Walsh, J.; Del Burgo, C.

2007-07-01

We present a 127 × 63-deg2 extinction map of the Anticentre of the Galaxy, based on < J - H > and < H - K > colour excess maps from the Two-Micron All-Sky Survey. This 8001-deg2 map with a resolution of 4 arcmin is provided as online material. The colour excess ratio < J - H >/< H - K > is used to determine the power-law index of the reddening law (β) for individual regions contained in the area (e.g. Orion, Perseus, Taurus, Auriga, Monoceros, Camelopardalis, Cassiopeia). On average we find a dominant value of β = 1.8 +/- 0.2 for the individual clouds, in agreement with the canonical value for the interstellar medium. We also show that there is an internal scatter of β values in these regions, and that in some areas more than one dominant β values are present. This indicates large-scale variations in the dust properties. The analysis of the AV values within individual regions shows a change in the slope of the column density distribution with distance. This can be attributed either to a change in the governing physical processes in molecular clouds on spatial scales of about 1pc or to an AV dilution with distance in our map.

Multisensor monitoring of deforestation in the Guinea Highlands of West Africa

NASA Technical Reports Server (NTRS)

Gilruth, Peter T.; Hutchinson, Charles F.

1990-01-01

Multiple remote sensing systems were used to assess deforestation in the Guinea Highlands (Fouta Djallon) of West Africa. Sensor systems included: (1) historical (1953) and current (1989) aerial mapping photography; (2) current large-scale, small format (35mm) aerial photography; (3) current aerial video imagery; and (4) historical (1973) and recent (1985) LANDSAT MSS. Photographic and video data were manually interpreted and incorporated in a vector-based geographic information system (GIS). LANDSAT data were digitally classified. General results showed an increase in permanent and shifting agriculture over the past 35 years. This finding is consistent with hypothesized strategies to increase agricultural production through a shortening of the fallow period in areas of shifting cultivation. However, results also show that the total area of both permanent and shifting agriculture had expanded at the expense of natural vegetation and an increase in erosion. Although sequential LANDSAT MSS cannot be used in this region to accurately map land over, the location, direction and magnitude of changes can be detected in relative terms. Historical and current aerial photography can be used to map agricultural land use changes with some accuracy. Video imagery is useful as ancillary data for mapping vegetation. The most prudent approach to mapping deforestation would incorporate a multistage approach based on these sensors.

Map visualization of groundwater withdrawals at the sub-basin scale

NASA Astrophysics Data System (ADS)

Goode, Daniel J.

2016-06-01

A simple method is proposed to visualize the magnitude of groundwater withdrawals from wells relative to user-defined water-resource metrics. The map is solely an illustration of the withdrawal magnitudes, spatially centered on wells—it is not capture zones or source areas contributing recharge to wells. Common practice is to scale the size (area) of withdrawal well symbols proportional to pumping rate. Symbols are drawn large enough to be visible, but not so large that they overlap excessively. In contrast to such graphics-based symbol sizes, the proposed method uses a depth-rate index (length per time) to visualize the well withdrawal rates by volumetrically consistent areas, called "footprints". The area of each individual well's footprint is the withdrawal rate divided by the depth-rate index. For example, the groundwater recharge rate could be used as a depth-rate index to show how large withdrawals are relative to that recharge. To account for the interference of nearby wells, composite footprints are computed by iterative nearest-neighbor distribution of excess withdrawals on a computational and display grid having uniform square cells. The map shows circular footprints at individual isolated wells and merged footprint areas where wells' individual footprints overlap. Examples are presented for depth-rate indexes corresponding to recharge, to spatially variable stream baseflow (normalized by basin area), and to the average rate of water-table decline (scaled by specific yield). These depth-rate indexes are water-resource metrics, and the footprints visualize the magnitude of withdrawals relative to these metrics.

Map visualization of groundwater withdrawals at the sub-basin scale

USGS Publications Warehouse

Goode, Daniel J.

2016-01-01

A simple method is proposed to visualize the magnitude of groundwater withdrawals from wells relative to user-defined water-resource metrics. The map is solely an illustration of the withdrawal magnitudes, spatially centered on wells—it is not capture zones or source areas contributing recharge to wells. Common practice is to scale the size (area) of withdrawal well symbols proportional to pumping rate. Symbols are drawn large enough to be visible, but not so large that they overlap excessively. In contrast to such graphics-based symbol sizes, the proposed method uses a depth-rate index (length per time) to visualize the well withdrawal rates by volumetrically consistent areas, called “footprints”. The area of each individual well’s footprint is the withdrawal rate divided by the depth-rate index. For example, the groundwater recharge rate could be used as a depth-rate index to show how large withdrawals are relative to that recharge. To account for the interference of nearby wells, composite footprints are computed by iterative nearest-neighbor distribution of excess withdrawals on a computational and display grid having uniform square cells. The map shows circular footprints at individual isolated wells and merged footprint areas where wells’ individual footprints overlap. Examples are presented for depth-rate indexes corresponding to recharge, to spatially variable stream baseflow (normalized by basin area), and to the average rate of water-table decline (scaled by specific yield). These depth-rate indexes are water-resource metrics, and the footprints visualize the magnitude of withdrawals relative to these metrics.

GIS-based rare events logistic regression for mineral prospectivity mapping

NASA Astrophysics Data System (ADS)

Xiong, Yihui; Zuo, Renguang

2018-02-01

Mineralization is a special type of singularity event, and can be considered as a rare event, because within a specific study area the number of prospective locations (1s) are considerably fewer than the number of non-prospective locations (0s). In this study, GIS-based rare events logistic regression (RELR) was used to map the mineral prospectivity in the southwestern Fujian Province, China. An odds ratio was used to measure the relative importance of the evidence variables with respect to mineralization. The results suggest that formations, granites, and skarn alterations, followed by faults and aeromagnetic anomaly are the most important indicators for the formation of Fe-related mineralization in the study area. The prediction rate and the area under the curve (AUC) values show that areas with higher probability have a strong spatial relationship with the known mineral deposits. Comparing the results with original logistic regression (OLR) demonstrates that the GIS-based RELR performs better than OLR. The prospectivity map obtained in this study benefits the search for skarn Fe-related mineralization in the study area.

Human population, urban settlement patterns and their impact on Plasmodium falciparum malaria endemicity.

PubMed

Tatem, Andrew J; Guerra, Carlos A; Kabaria, Caroline W; Noor, Abdisalan M; Hay, Simon I

2008-10-27

The efficient allocation of financial resources for malaria control and the optimal distribution of appropriate interventions require accurate information on the geographic distribution of malaria risk and of the human populations it affects. Low population densities in rural areas and high population densities in urban areas can influence malaria transmission substantially. Here, the Malaria Atlas Project (MAP) global database of Plasmodium falciparum parasite rate (PfPR) surveys, medical intelligence and contemporary population surfaces are utilized to explore these relationships and other issues involved in combining malaria risk maps with those of human population distribution in order to define populations at risk more accurately. First, an existing population surface was examined to determine if it was sufficiently detailed to be used reliably as a mask to identify areas of very low and very high population density as malaria free regions. Second, the potential of international travel and health guidelines (ITHGs) for identifying malaria free cities was examined. Third, the differences in PfPR values between surveys conducted in author-defined rural and urban areas were examined. Fourth, the ability of various global urban extent maps to reliably discriminate these author-based classifications of urban and rural in the PfPR database was investigated. Finally, the urban map that most accurately replicated the author-based classifications was analysed to examine the effects of urban classifications on PfPR values across the entire MAP database. Masks of zero population density excluded many non-zero PfPR surveys, indicating that the population surface was not detailed enough to define areas of zero transmission resulting from low population densities. In contrast, the ITHGs enabled the identification and mapping of 53 malaria free urban areas within endemic countries. Comparison of PfPR survey results showed significant differences between author-defined 'urban' and 'rural' designations in Africa, but not for the remainder of the malaria endemic world. The Global Rural Urban Mapping Project (GRUMP) urban extent mask proved most accurate for mapping these author-defined rural and urban locations, and further sub-divisions of urban extents into urban and peri-urban classes enabled the effects of high population densities on malaria transmission to be mapped and quantified. The availability of detailed, contemporary census and urban extent data for the construction of coherent and accurate global spatial population databases is often poor. These known sources of uncertainty in population surfaces and urban maps have the potential to be incorporated into future malaria burden estimates. Currently, insufficient spatial information exists globally to identify areas accurately where population density is low enough to impact upon transmission. Medical intelligence does however exist to reliably identify malaria free cities. Moreover, in Africa, urban areas that have a significant effect on malaria transmission can be mapped.

Geologic mapping of Northern Atla Regio on Venus: Preliminary data

NASA Technical Reports Server (NTRS)

Nikishin, A. M.; Burba, G. A.

1993-01-01

The Northern part of Atla Regio within the frame of C1-formate Magellan photo map 15N197 was mapped geologically at scale 1:8,000,000. This is a part of Russia's contribution into C1 geologic mapping efforts. The map is reproduced here being reduced about twice. The map shows that the Northern Atla area is predominantly a volcanic plain with numerous volcanic features: shield volcanoes, domes and hills with various morphology, corona-like constructions, radar bright and dark spots often with flow-like outlines. Relatively small areas of tessera occurred in the area are mainly semi-flooded with the plain material. Tesserae are considered to be the oldest terrains within the map sheet. There are many lineated terrains in the region. They are interpreted as the old, almost-buried tesserae (those with crossed lineaments) or partly buried ridge belts (those with parallel lineaments). These lineated terrains have an intermediate age between the young volcanic plains and the old tessera areas. Two prominent high volcanic shields are located within the region - Ozza Mons and Sapas Mona. The most prominent structure in Northern Atla is Ganis Chasma rift. The rift cuts volcanic plain and is considered to be under formation during approximately the same time with Ozza Mons shield. Ganis Chasma rift valley is highly fractured and bounded with fault scarps. Rift shoulder uplifts are typical for Ganis Chasma. There are few relatively young volcanic features inside the rift valley. The analysis of fracturing and rift valley geometry shows the rift originated due to 5-10 percent crustal extention followed by the crustal subsidence. The age sequence summary for the main terrain types in the region is (from older to younger ones): tesserae; lineated terrains with crossed lineaments; lineated terrains with parallel lineaments; volcanic plains; and prominent volcanic shields and Ganis Chasma rift valley. The geologic structure of Atla Regio as it appeared now with the Magellan high resolution images is very close to that of Beta Regio. Such conclusion coincide with the earlier ones based on the coarser data.

Long-term development of the Czech landscape studied on the basis of old topographic maps

NASA Astrophysics Data System (ADS)

Skokanová, H.; Havlíček, M.

2009-04-01

The paper deals with long-term land use changes in the Czech Republic with the help of old topographic maps. Departments of Landscape Ecology and GIS Applications from the Silva Tarouca Research Institute for Landscape and Ornamental Gardening, v.v.i. study these changes mainly in the research project MSM 6293359101 Research into sources and indicators of biodiversity in cultural landscape in the context of its fragmentation dynamics, the subpart Quantitative analysis of the dynamics of the Czech landscape development. In this paper, the authors concentrate mainly on map sources, which were acquired for the purpose of the project and also introduce partial results. Maps, which are the sources for the analyses, are following: maps from 2nd Austrian military survey in the scale 1:28 800 (created for the territory of the Czech Republic in the period 1836-1852), maps from 3rd Austrian military survey in the scale 1:25 000 (created for the Czech Republic in the period 1876-1880), Czechoslovak military topographic maps in the scale 1:25 000 from 1950s and 1990s, and Czech topographic base maps in the scale 1:10 000 from 2002-2006. It is necessary to complete maps of the 2nd and 3rd Austrian military survey thanks to their incompleteness, mainly along state borders. Also maps from 1nd Austrian military survey in the scale 1:28 800 (created for the Czech Republic in the period 1764-1783) are available; however, their usage for the accurate analyses in the GIS environment is restricted by their poor cartographic accuracy. Apart of the above mentioned maps, there has been progress in collecting maps from the interwar and war period (revised maps of the 3rd Austrian military survey maps, maps of the provisional military survey from 1923-1933, maps of definitive military survey from 1934-1938 and maps from survey of Moravian part of the Protectorate of Bohemia and Moravia, so called Messtischblätter from 1939-1945). Maps from five periods are manually vectorised in the GIS environment. When vectorizing maps, nine land use categories are distinguished according to the methodology created at the author's workplace. Only areas larger than 0.8 ha are vectorized with regard to the output scale of the project (1:200 000), which includes the whole territory of the republic. The so far vectorized areas are shown in the overview maps. The main analyses lay in overlaying vectorized maps and in calculation of the number of land use changes for the whole researched period. These then show stable areas, i.e. areas where no change in land use occurred, and dynamic areas with one or more changes. Also types of the land use changes both among individual maps and for the whole period can be detected.

Geologic map of the greater Denver area, Front Range urban corridor, Colorado

USGS Publications Warehouse

Trimble, Donald E.; Machette, Michael N.

1979-01-01

This digital map shows the areal extent of surficial deposits and rock stratigraphic units (formations) as compiled by Trimble and Machette from 1973 to 1977 and published in 1979 under the Front Range Urban Corridor Geology Program. Trimble and Machette compiled their geologic map from published geologic maps and unpublished geologic mapping having varied map unit schemes. A convenient feature of the compiled map is its uniform classification of geologic units that mostly matches those of companion maps to the north (USGS I-855-G) and to the south (USGS I-857-F). Published as a color paper map, the Trimble and Machette map was intended for land-use planning in the Front Range Urban Corridor. This map recently (1997-1999) was digitized under the USGS Front Range Infrastructure Resources Project. In general, the mountainous areas in the western part of the map exhibit various igneous and metamorphic bedrock units of Precambrian age, major faults, and fault brecciation zones at the east margin (5-20 km wide) of the Front Range. The eastern and central parts of the map (Colorado Piedmont) depict a mantle of unconsolidated deposits of Quaternary age and interspersed outcroppings of Cretaceous or Tertiary-Cretaceous sedimentary bedrock. The Quaternary mantle comprises eolian deposits (quartz sand and silt), alluvium (gravel, sand, and silt of variable composition), colluvium, and a few landslides. At the mountain front, north-trending, dipping Paleozoic and Mesozoic sandstone, shale, and limestone bedrock formations form hogbacks and intervening valleys.

Structural and functional changes across the visual cortex of a patient with visual form agnosia.

PubMed

Bridge, Holly; Thomas, Owen M; Minini, Loredana; Cavina-Pratesi, Cristiana; Milner, A David; Parker, Andrew J

2013-07-31

Loss of shape recognition in visual-form agnosia occurs without equivalent losses in the use of vision to guide actions, providing support for the hypothesis of two visual systems (for "perception" and "action"). The human individual DF received a toxic exposure to carbon monoxide some years ago, which resulted in a persisting visual-form agnosia that has been extensively characterized at the behavioral level. We conducted a detailed high-resolution MRI study of DF's cortex, combining structural and functional measurements. We present the first accurate quantification of the changes in thickness across DF's occipital cortex, finding the most substantial loss in the lateral occipital cortex (LOC). There are reduced white matter connections between LOC and other areas. Functional measures show pockets of activity that survive within structurally damaged areas. The topographic mapping of visual areas showed that ordered retinotopic maps were evident for DF in the ventral portions of visual cortical areas V1, V2, V3, and hV4. Although V1 shows evidence of topographic order in its dorsal portion, such maps could not be found in the dorsal parts of V2 and V3. We conclude that it is not possible to understand fully the deficits in object perception in visual-form agnosia without the exploitation of both structural and functional measurements. Our results also highlight for DF the cortical routes through which visual information is able to pass to support her well-documented abilities to use visual information to guide actions.

Map showing availability of hydrologic data published by the U.S. Environmental Data Service and by the U.S. Geological Survey and cooperative agencies, greater Denver area, Front Range Urban Corridor, Colorado

USGS Publications Warehouse

Hampton, E.R.

1975-01-01

What is the rainfall of this region? What areas are prone to periodic flooding? What is the water supply? What is the chemical quality of the ground water and water in the streams? How deep is the water table? Which streams are gaged, and where? These and similar questions are being asked regularly by land and resource developers, urban planners, industrial consultants, and governmental resource managers. This map provides the first step toward answering these questions. It shows by symbols and color the hydrologic data published as of January 1974 for the Greater Denver area by the U.S. Environmental Data Service and by the U.S. Geological Survey and cooperating agencies, and the points or areas where these data have been collected. The sources of the data are given in both the following discussion and the references.

Improved regional-scale Brazilian cropping systems' mapping based on a semi-automatic object-based clustering approach

NASA Astrophysics Data System (ADS)

Bellón, Beatriz; Bégué, Agnès; Lo Seen, Danny; Lebourgeois, Valentine; Evangelista, Balbino Antônio; Simões, Margareth; Demonte Ferraz, Rodrigo Peçanha

2018-06-01

Cropping systems' maps at fine scale over large areas provide key information for further agricultural production and environmental impact assessments, and thus represent a valuable tool for effective land-use planning. There is, therefore, a growing interest in mapping cropping systems in an operational manner over large areas, and remote sensing approaches based on vegetation index time series analysis have proven to be an efficient tool. However, supervised pixel-based approaches are commonly adopted, requiring resource consuming field campaigns to gather training data. In this paper, we present a new object-based unsupervised classification approach tested on an annual MODIS 16-day composite Normalized Difference Vegetation Index time series and a Landsat 8 mosaic of the State of Tocantins, Brazil, for the 2014-2015 growing season. Two variants of the approach are compared: an hyperclustering approach, and a landscape-clustering approach involving a previous stratification of the study area into landscape units on which the clustering is then performed. The main cropping systems of Tocantins, characterized by the crop types and cropping patterns, were efficiently mapped with the landscape-clustering approach. Results show that stratification prior to clustering significantly improves the classification accuracies for underrepresented and sparsely distributed cropping systems. This study illustrates the potential of unsupervised classification for large area cropping systems' mapping and contributes to the development of generic tools for supporting large-scale agricultural monitoring across regions.

Earthquakes in Virginia and vicinity 1774 - 2004

USGS Publications Warehouse

Tarr, Arthur C.; Wheeler, Russell L.

2006-01-01

This map summarizes two and a third centuries of earthquake activity. The seismic history consists of letters, journals, diaries, and newspaper and scholarly articles that supplement seismograph recordings (seismograms) dating from the early twentieth century to the present. All of the pre-instrumental (historical) earthquakes were large enough to be felt by people or to cause shaking damage to buildings and their contents. Later, widespread use of seismographs meant that tremors too small or distant to be felt could be detected and accurately located. Earthquakes are a legitimate concern in Virginia and parts of adjacent States. Moderate earthquakes cause slight local damage somewhere in the map area about twice a decade on the average. Additionally, many buildings in the map area were constructed before earthquake protection was added to local building codes. The large map shows all historical and instrumentally located earthquakes from 1774 through 2004.

Volcanism on Io: Insights from Global Geologic Mapping

NASA Technical Reports Server (NTRS)

Williams, D. A.; Keszthelyi, L. P.; Crown, D. A.; Geissler, P. E.; Schenk, P. M.; Yff, Jessica; Jaeger, W. L.

2009-01-01

We are preparing a new global geo-logic map of Jupiter s volcanic moon, Io. Here we report the type of data that are now available from our global mapping efforts, and how these data can be used to investigate questions regarding the volcano-tectonic evolution of Io. We are using the new map to investigate several specific questions about the geologic evolution of Io that previously could not be well addressed, including (for example) a comparison of the areas vs. the heights of Ionian mountains to assess their stability and evolution (Fig. 1). The area-height relationships of Io s visible mountains show the low abundance and low relief of volcanic mountains (tholi) relative to tectonic mountains, consistent with formation from low-viscosity lavas less likely to build steep edifices. Mottled mountains are generally less high than lineated mountains, consistent with a degradational formation.

Application of Poisson kriging to the mapping of cholera and dysentery incidence in an endemic area of Bangladesh.

PubMed

Ali, Mohammad; Goovaerts, Pierre; Nazia, Nushrat; Haq, M Zahirul; Yunus, Mohammad; Emch, Michael

2006-10-13

Disease maps can serve to display incidence rates geographically, to inform on public health provision about the success or failure of interventions, and to make hypothesis or to provide evidences concerning disease etiology. Poisson kriging was recently introduced to filter the noise attached to rates recorded over sparsely populated administrative units. Its benefit over simple population-weighted averages and empirical Bayesian smoothers was demonstrated by simulation studies using county-level cancer mortality rates. This paper presents the first application of Poisson kriging to the spatial interpolation of local disease rates, resulting in continuous maps of disease rate estimates and the associated prediction variance. The methodology is illustrated using cholera and dysentery data collected in a cholera endemic area (Matlab) of Bangladesh. The spatial analysis was confined to patrilineally-related clusters of households, known as baris, located within 9 kilometers from the Matlab hospital to avoid underestimating the risk of disease incidence, since patients far away from the medical facilities are less likely to travel. Semivariogram models reveal a range of autocorrelation of 1.1 km for dysentery and 0.37 km for cholera. This result translates into a cholera risk map that is patchier than the dysentery map that shows a large zone of high incidence in the south-central part of the study area, which is quasi-urban. On both maps, lower risk values are found in the Northern part of the study area, which is also the most distant from the Matlab hospital. The weaker spatial continuity of cholera versus dysentery incidence rates resulted in larger kriging variance across the study area. The approach presented in this paper enables researchers to incorporate the pattern of spatial dependence of incidence rates into the mapping of risk values and the quantification of the associated uncertainty. Differences in spatial patterns, in particular the range of spatial autocorrelation, reflect differences in the mode of transmission of cholera and dysentery. Our risk maps for cholera and dysentery incidences should help identifying putative factors of increased disease incidence, leading to more effective prevention and remedial actions in endemic areas.

Application of Poisson kriging to the mapping of cholera and dysentery incidence in an endemic area of Bangladesh

PubMed Central

Ali, Mohammad; Goovaerts, Pierre; Nazia, Nushrat; Haq, M Zahirul; Yunus, Mohammad; Emch, Michael

2006-01-01

Background Disease maps can serve to display incidence rates geographically, to inform on public health provision about the success or failure of interventions, and to make hypothesis or to provide evidences concerning disease etiology. Poisson kriging was recently introduced to filter the noise attached to rates recorded over sparsely populated administrative units. Its benefit over simple population-weighted averages and empirical Bayesian smoothers was demonstrated by simulation studies using county-level cancer mortality rates. This paper presents the first application of Poisson kriging to the spatial interpolation of local disease rates, resulting in continuous maps of disease rate estimates and the associated prediction variance. The methodology is illustrated using cholera and dysentery data collected in a cholera endemic area (Matlab) of Bangladesh. Results The spatial analysis was confined to patrilineally-related clusters of households, known as baris, located within 9 kilometers from the Matlab hospital to avoid underestimating the risk of disease incidence, since patients far away from the medical facilities are less likely to travel. Semivariogram models reveal a range of autocorrelation of 1.1 km for dysentery and 0.37 km for cholera. This result translates into a cholera risk map that is patchier than the dysentery map that shows a large zone of high incidence in the south-central part of the study area, which is quasi-urban. On both maps, lower risk values are found in the Northern part of the study area, which is also the most distant from the Matlab hospital. The weaker spatial continuity of cholera versus dysentery incidence rates resulted in larger kriging variance across the study area. Conclusion The approach presented in this paper enables researchers to incorporate the pattern of spatial dependence of incidence rates into the mapping of risk values and the quantification of the associated uncertainty. Differences in spatial patterns, in particular the range of spatial autocorrelation, reflect differences in the mode of transmission of cholera and dysentery. Our risk maps for cholera and dysentery incidences should help identifying putative factors of increased disease incidence, leading to more effective prevention and remedial actions in endemic areas. PMID:17038192

Rectification of historical topographic maps: a tool revealing the course changes and dynamics of Lower Gaula River, South Trondelag, Norway

NASA Astrophysics Data System (ADS)

Timár, Gábor; Baranya, Sándor; Rüther, Nils; Kvarteig, Sidsel; Galambos, Csilla; Biszak, Előd; Nagy, Diána

2017-04-01

The 1:50,000 and 1:100,000 scale historical sheets of the Norwegian topographic 'Rektangelkart' map series were georeferenced, in order to obtain the original hydrography of the Gaula River, at a ca 50 kilometer long section between Støren and the estuary to the Gulosen Bay. The 1:50,000 scale sheets are the earliest systematic topographic works of the area, surveyed in 1866-9, while the smaller scale sheets were surveyed forty years later, in 1906-8. Both series represent a river status before the extensive control works. Thus, together with the modern, present-day cartographic and GIS products, these two 'snapshots' from 100 and 150 years ago show not only the original, uncontrolled status of the river but also some elements of the natural changes of the course/thalweg. To make the georeference, instead of using terrain points, the geodetic parameters of the Norwegian 'Rektangelkart' series were defined in GIS environment. The Cassini map projection was defined with a projection center in the fortress of Kongsvinger, Eastern Norway, some 350 kilometers from the study area. Knowing the sheet labeling system and the terrain position of the sheets in this Cassini projection, only their four corner points were defined in all sheets. The accuracy of the horizontal control of georeferenced was less than half map millimeter (25/50 meters). The sheets show an interesting meander cutoff process between Ler and Kvål. In 1869, the meander curve is still active and fully operating. A cutoff channel is clearly mapped in 1906, together with the old one. Nowadays, almost no map signs show the old channel course, however in the field, it is still traceable. Another interesting map element shows the complete bar structure in the channel. These gravel bars showed a different pattern in the old maps, as there were more gravel sediments in the time before the building of upspring reservoirs. Gravel bars are important in some environmental processes, eg. as salmon habitats, This database shows their original status, providing an important input for environmental engineering. The research was carried out in the frame of EEA/156/M4-0002 project.

Classifying unresolved objects from simulated space data.

NASA Technical Reports Server (NTRS)

Nalepka, R. F.; Hyde, P. D.

1973-01-01

A multispectral scanner data set gathered at a flight altitude of 10,000 ft. over an agricultural area was modified to simulate the spatial resolution of the spacecraft scanners. Signatures were obtained for several major crops and their proportions were estimated over a large area. For each crop, a map was generated to show its approximate proportion in each resolution element, and hence its distribution over the area of interest. A statistical criterion was developed to identify data points that may not represent a mixture of the specified crops. This allows for great reduction in the effect of unknown or alien objects on the estimated proportions. This criterion can be used to locate special features, such as roads or farm houses. Preliminary analysis indicates a high level of consistency between estimated proportions and available ground truth. Large concentrations of major crops show up especially well on the maps.

DeepSurveyCam—A Deep Ocean Optical Mapping System

PubMed Central

Kwasnitschka, Tom; Köser, Kevin; Sticklus, Jan; Rothenbeck, Marcel; Weiß, Tim; Wenzlaff, Emanuel; Schoening, Timm; Triebe, Lars; Steinführer, Anja; Devey, Colin; Greinert, Jens

2016-01-01

Underwater photogrammetry and in particular systematic visual surveys of the deep sea are by far less developed than similar techniques on land or in space. The main challenges are the rough conditions with extremely high pressure, the accessibility of target areas (container and ship deployment of robust sensors, then diving for hours to the ocean floor), and the limitations of localization technologies (no GPS). The absence of natural light complicates energy budget considerations for deep diving flash-equipped drones. Refraction effects influence geometric image formation considerations with respect to field of view and focus, while attenuation and scattering degrade the radiometric image quality and limit the effective visibility. As an improvement on the stated issues, we present an AUV-based optical system intended for autonomous visual mapping of large areas of the seafloor (square kilometers) in up to 6000 m water depth. We compare it to existing systems and discuss tradeoffs such as resolution vs. mapped area and show results from a recent deployment with 90,000 mapped square meters of deep ocean floor. PMID:26828495

Definition and GIS-based characterization of an integral risk index applied to a chemical/petrochemical area.

PubMed

Nadal, Martí; Kumar, Vikas; Schuhmacher, Marta; Domingo, José L

2006-08-01

A risk map of the chemical/petrochemical industrial area of Tarragona (Catalonia, Spain) was designed following a two-stage procedure. The first step was the creation of a ranking system (Hazard Index) for a number of different inorganic and organic pollutants: heavy metals, polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), polychlorinated biphenyls (PCBs) and polychlorinated aromatic hydrocarbons (PAHs) by applying self-organizing maps (SOM) to persistence, bioaccumulation and toxicity properties of the chemicals. PCBs seemed to be the most hazardous compounds, while the light PAHs showed the minimum values. Subsequently, an Integral Risk Index was developed taking into account the Hazard Index and the concentrations of all pollutants in soil samples collected in the assessed area of Tarragona. Finally, a risk map was elaborated by representing the spatial distribution of the Integral Risk Index with a geographic information system (GIS). The results of the present study seem to indicate that the development of an integral risk map might be useful to help in making-decision processes concerning environmental pollutants.

Comparison of traditional burn wound mapping with a computerized program.

PubMed

Williams, James F; King, Booker T; Aden, James K; Serio-Melvin, Maria; Chung, Kevin K; Fenrich, Craig A; Salinas, José; Renz, Evan M; Wolf, Steven E; Blackbourne, Lorne H; Cancio, Leopoldo C

2013-01-01

Accurate burn estimation affects the use of burn resuscitation formulas and treatment strategies, and thus can affect patient outcomes. The objective of this process-improvement project was to compare the accuracy of a computer-based burn mapping program, WoundFlow (WF), with the widely used hand-mapped Lund-Browder (LB) diagram. Manikins with various burn representations (from 1% to more than 60% TBSA) were used for comparison of the WF system and LB diagrams. Burns were depicted on the manikins using red vinyl adhesive. Healthcare providers responsible for mapping of burn patients were asked to perform burn mapping of the manikins. Providers were randomized to either an LB or a WF group. Differences in the total map area between groups were analyzed. Also, direct measurements of the burn representations were taken and compared with LB and WF results. The results of 100 samples, compared using Bland-Altman analysis, showed no difference between the two methods. WF was as accurate as LB mapping for all burn surface areas. WF may be additionally beneficial in that it can track daily progress until complete wound closure, and can automatically calculate burn size, thus decreasing the chances of mathematical errors.

Groundwater vulnerability assessment using hydrogeologic and geoelectric layer susceptibility indexing at Igbara Oke, Southwestern Nigeria

NASA Astrophysics Data System (ADS)

Oni, T. E.; Omosuyi, G. O.; Akinlalu, A. A.

2017-12-01

Groundwater vulnerability assessment was carried out at Igbara Oke Southwestern Nigeria, with a view to classify the area into vulnerability zones, by applying the electrical resistivity method, using Schlumberger electrode arrays with maximum electrode separation (AB/2) of 65 m in (41) different locations for data acquisition. Geoelectric parameters (layer resistivity and thickness) were determined from the interpreted data. The study area comprises four geoelectric layers (topsoil, lateritic layer, weathered/fractured layer and fresh basement). The geoelectric parameters of the overlying layers across the area were used to assess the vulnerability of the underlying aquifers to near-surface contaminants with the aid of vulnerability maps generated. Three models were compared by maps using geo-electrically derived models; longitudinal conductance, GOD (groundwater occurrence, overlying lithology and depth to the aquifer) and GLSI (geoelectric layer susceptibility indexing). The total longitudinal conductance map shows the north central part of the study area as a weakly protected (0.1-0.19) area, while the northern and southern parts have poor protective capacity (<0.1); this is in agreement with the GOD method which shows the northern part of the study area as less vulnerable (0-0.1) while the southern part has low/moderate (0.1-0.3) vulnerability to contamination. The longitudinal conductance exaggerates the degree of susceptibility to contamination than the GOD and GLSI models. From the models, vulnerability to contamination can be considered higher at the southern part than the northern part and therefore, sources of contamination like septic tank, refuse dump should be cited far from groundwater development area.

Use of a ground-water flow model with particle tracking to evaluate ground-water vulnerability, Clark County, Washington

USGS Publications Warehouse

Snyder, D.T.; Wilkinson, J.M.; Orzol, L.L.

1996-01-01

A ground-water flow model was used in conjunction with particle tracking to evaluate ground-water vulnerability in Clark County, Washington. Using the particle-tracking program, particles were placed in every cell of the flow model (about 60,000 particles) and tracked backwards in time and space upgradient along flow paths to their recharge points. A new computer program was developed that interfaces the results from a particle-tracking program with a geographic information system (GIS). The GIS was used to display and analyze the particle-tracking results. Ground-water vulnerability was evaluated by selecting parts of the ground-water flow system and combining the results with ancillary information stored in the GIS to determine recharge areas, characteristics of recharge areas, downgradient impact of land use at recharge areas, and age of ground water. Maps of the recharge areas for each hydrogeologic unit illustrate the presence of local, intermediate, or regional ground-water flow systems and emphasize the three-dimensional nature of the ground-water flow system in Clark County. Maps of the recharge points for each hydrogeologic unit were overlaid with maps depicting aquifer sensitivity as determined by DRASTIC (a measure of the pollution potential of ground water, based on the intrinsic characteristics of the near-surface unsaturated and saturated zones) and recharge from on-site waste-disposal systems. A large number of recharge areas were identified, particularly in southern Clark County, that have a high aquifer sensitivity, coincide with areas of recharge from on-site waste-disposal systems, or both. Using the GIS, the characteristics of the recharge areas were related to the downgradient parts of the ground-water system that will eventually receive flow that has recharged through these areas. The aquifer sensitivity, as indicated by DRASTIC, of the recharge areas for downgradient parts of the flow system was mapped for each hydrogeologic unit. A number of public-supply wells in Clark County may be receiving a component of water that recharged in areas that are more conducive to contaminant entry. The aquifer sensitivity maps illustrate a critical deficiency in the DRASTIC methodology: the failure to account for the dynamics of the ground-water flow system. DRASTIC indices calculated for a particular location thus do not necessarily reflect the conditions of the ground-water resources at the recharge areas to that particular location. Each hydrogeologic unit was also mapped to highlight those areas that will eventually receive flow from recharge areas with on-site waste-disposal systems. Most public-supply wells in southern Clark County may eventually receive a component of water that was recharged from on-site waste-disposal systems.Traveltimes from particle tracking were used to estimate the minimum and maximum age of ground water within each model-grid cell. Chlorofluorocarbon (CFC)-age dating of ground water from 51 wells was used to calibrate effective porosity values used for the particle- tracking program by comparison of ground-water ages determined through the use of the CFC-age dating with those calculated by the particle- tracking program. There was a 76 percent agreement in predicting the presence of modern water in the 51 wells as determined using CFCs and calculated by the particle-tracking program. Maps showing the age of ground water were prepared for all the hydrogeologic units. Areas with the youngest ground-water ages are expected to be at greatest risk for contamination from anthropogenic sources. Comparison of these maps with maps of public- supply wells in Clark County indicates that most of these wells may withdraw ground water that is, in part, less than 100 years old, and in many instances less than 10 years old. Results of the analysis showed that a single particle-tracking analysis simulating advective transport can be used to evaluate ground-water vulnerability for any part of a ground-wate

Altitude of the top of the Inyan Kara Group in the Black Hills area, South Dakota

USGS Publications Warehouse

Carter, Janet M.; Redden, Jack A.

2000-01-01

This map is a product of the Black Hills Hydrology Study, which was initiated in 1990 to assess the quantity, quality, and distribution of surface water and ground water in the Black Hills area of South Dakota (Driscoll, 1992). This long-term study is a cooperative effort between the U.S. Geological Survey (USGS), the South Dakota Department of Environment and Natural Resources, and the West Dakota Water Development District, which represents various local and county cooperators. This map is part of a series of 1:100,000-scale maps for the study. The maps include a hydrogeologic map, structure-contour maps (altitudes of the tops of formations) for five formations that contain major aquifers in the study area, and potentiometric maps for these five major aquifers (the Inyan Kara, Minnekahta, Minnelusa, Madison, and Deadwood aquifers).The study area consists of the topographically defined Black Hills and adjacent areas located in western South Dakota. The Black Hills area is an elongated, dome-shaped feature, about 125 miles long and 60 miles wide, which was uplifted during the Laramide orogeny (Feldman and Heimlich, 1980). The oldest geologic units in the study area are Precambrian metamorphic and igneous rocks, which are exposed in the central core of the Black Hills. Surrounding the Precambrian core is a layered series of sedimentary rocks including limestones, sandstones, and shales that are exposed in roughly concentric rings around the uplifted flanks of the Black Hills. The bedrock sedimentary units typically dip away from the uplifted Black Hills at angles that approach or exceed 10 degrees near the outcrops, and decrease with distance from the uplift. Many of the sedimentary units contain aquifers, both within and beyond the study area. Recharge to these aquifers occurs from infiltration of precipitation upon the outcrops and, in some cases, from infiltration of streamflow (Hortness and Driscoll, 1998). Artesian conditions generally exist within these aquifers where an upper confining layer is present. Flowing wells and artesian springs that originate from confined aquifers are common around the periphery of the Black Hills.The purpose of this map is to show the altitude of the top (structure contours) of the Inyan Kara Group within the area of the Black Hills Hydrology Study. The depth to the top of the Inyan Kara Group can be estimated at a specific site by subtracting the altitude of the top of the formation from the topographic elevation. However, caution is urged in determining the depth to the top of the formation in areas on the map where the contours are approximately located.

Tampa Bay environmental atlas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kunneke, J.T.; Palik, T.F.

1984-12-01

Biological and water resource data for Tampa Bay were compiled and mapped at a scale of 1:24,000. This atlas consists of (1) composited information overlain on 18 biological and 20 water resource base maps and (2) an accompanying map narrative. Subjects mapped on the water resource maps are contours of the mean middepth specific conductivity which can be converted to salinity; bathymetry, sediments, tidal currents, the freshwater/saltwater interface, dredge spoil disposal sites; locations of industrial and municipal point source discharges, tide stations, and water quality sampling stations. The point source discharge locations show permitted capacity and the water quality samplingmore » stations show 5-year averages for chlorophyll, conductivity, turbidity, temperature, and total nitrogen. The subjects shown on the biological resource maps are clam and oyster beds, shellfish harvest areas, colonial bird nesting sites, manatee habitat, seagrass beds and artificial reefs. Spawning seasons, nursery habitats, and adult habitats are identified for major fish species. The atlas will provide useful information for coastal planning and management in Tampa Bay.« less

Hydrologic feasibility of artificial forestation in the semi-arid Loess Plateau of China

NASA Astrophysics Data System (ADS)

Jin, T. T.; Fu, B. J.; Liu, G. H.; Wang, Z.

2011-08-01

Hydrologic viability, in terms of moisture availability, is fundamental to ecosystem sustainability in arid and semi-arid regions. In this study, we examine the spatial distribution and after-planting variations of soil moisture content (SMC) in black locust tree (Robinia pseudoacacia L.) plantings in the Loess Plateau of China at a regional scale. Thirty sites (5 to 45 yr old) were selected, spanning an area of 300 km by 190 km in the northern region of the Shaanxi Province. The SMC was measured to a depth of 100 cm at intervals of 10 cm. Geographical, topographic and vegetation information was recorded, and soil organic matter was evaluated. The results show that, at the regional scale, SMC spatial variability was most highly correlated with rainfall. The negative relationship between the SMC at a depth of 20-50 cm and the stand age was stronger than at other depths, although this relationship was not significant at a 5 % level. Watershed analysis shows that the after-planting SMC variation differed depending upon precipitation. The SMC of plantings in areas receiving sufficient precipitation (e.g., mean annual precipitation (MAP) of 617 mm) may increase with stand age due to improvements in soil water-holding capacity and water-retention abilities after planting. For areas experiencing water shortages (e.g., MAP = 509 mm), evapotranspiration may cause planting soils to dry within the first 20 yr of growth. It is expected that, as arid and semi-arid plantings age, evapotranspiration will decrease, and the soil profile may gradually recover. In extremely dry areas (e.g., MAP = 352 mm), the variation in after-planting SMC with stand age was found to be negligible. The MAP can be used as an index to divide the study area into different ecological regions. Afforestation may sequentially exert positive, negative and negligible effects on SMCs with a decrease in the MAP. Therefore, future restoration measures should correspond to the local climate conditions, and the MAP should be a major consideration for the Loess Plateau. Large-scale and long-term research on the effects of restoration projects on SMCs is needed to support more effective restoration policies. The interaction between afforestation and local environmental conditions, particularly water availability to plants, should be taken into account in afforestation campaigns in arid and semi-arid areas.

Mapping and Modelling Malaria Risk Areas Using Climate, Socio-Demographic and Clinical Variables in Chimoio, Mozambique.

PubMed

Ferrao, Joao L; Niquisse, Sergio; Mendes, Jorge M; Painho, Marco

2018-04-19

Background : Malaria continues to be a major public health concern in Africa. Approximately 3.2 billion people worldwide are still at risk of contracting malaria, and 80% of deaths caused by malaria are concentrated in only 15 countries, most of which are in Africa. These high-burden countries have achieved a lower than average reduction of malaria incidence and mortality, and Mozambique is among these countries. Malaria eradication is therefore one of Mozambique’s main priorities. Few studies on malaria have been carried out in Chimoio, and there is no malaria map risk of the area. This map is important to identify areas at risk for application of Public Precision Health approaches. By using GIS-based spatial modelling techniques, the research goal of this article was to map and model malaria risk areas using climate, socio-demographic and clinical variables in Chimoio, Mozambique. Methods : A 30 m × 30 m Landsat image, ArcGIS 10.2 and BioclimData were used. A conceptual model for spatial problems was used to create the final risk map. The risks factors used were: the mean temperature, precipitation, altitude, slope, distance to water bodies, distance to roads, NDVI, land use and land cover, malaria prevalence and population density. Layers were created in a raster dataset. For class value comparisons between layers, numeric values were assigned to classes within each map layer, giving them the same importance. The input dataset were ranked, with different weights according to their suitability. The reclassified outputs of the data were combined. Results : Chimoio presented 96% moderate risk and 4% high-risk areas. The map showed that the central and south-west “Residential areas”, namely, Centro Hipico, Trangapsso, Bairro 5 and 1° de Maio, had a high risk of malaria, while the rest of the residential areas had a moderate risk. Conclusions : The entire Chimoio population is at risk of contracting malaria, and the precise estimation of malaria risk, therefore, has important precision public health implications and for the planning of effective control measures, such as the proper time and place to spray to combat vectors, distribution of bed nets and other control measures.

Statistics of Petroleum Exploration in the World Outside the United States and Canada Through 2001

USGS Publications Warehouse

Attanasi, E.D.; Freeman, P.A.; Glovier, Jennifer A.

2007-01-01

Future oil and gas supplies depend, in part, on the reserves that are expected to be added through exploration and new discoveries. This Circular presents a summary of the statistics and an analysis of petroleum exploration in the world outside the United States and Canada (the study area) through 2001. It updates U.S. Geological Survey Circular 1096 (by E.D. Attanasi and D.H. Root, 1993) and expands coverage of the statistics to areas where drilling and discovery data have recently become available. These new areas include China, the formerly Communist countries of Eastern Europe, and the countries that once were part of the former Soviet Union in Europe and Asia. Data are presented by country but are organized by petroleum provinces delineated by the U.S. Geological Survey World Energy Assessment Team (USGS Digital Data Series DDS?60, published in 2000). The data and analysis are presented in maps and graphs, providing a visual summary of the exploration maturity of an area. The maps show the delineated prospective areas and explored areas through 2001; explored areas have a drilling density that would rule out the occurrence of undetected large petroleum accumulations. Graphs summarize the exploration yields in terms of cumulative recoverable discovered oil and gas by delineated prospective area. From 1992 through 2001 in areas outside the United States and Canada, the delineated prospective area expanded at a rate of about 50,000 square miles per year while the explored area grew at the rate of about 11,000 square miles per year. The delineated prospective area established by 1970 contains about 75 percent of the oil discovered to date in the study area. This area is slightly less than 40 percent of the delineated prospective area established through 2001. Maps and graphs show the extension of the delineated prospective area to deepwater areas offshore of Brazil and West Africa. From 1991 through 2000, offshore discoveries accounted for 59 percent of the oil and 77 percent of the gas discovered in the study area. The petroleum industry's decision to incur the greater costs of moving offshore and into deeper waters appears to be a response to the absence of onshore prospects of comparable quality. Where natural gas can be commercially developed and marketed, data show an expansion of exploration to target gas-prone areas.

NASA Damage Map Aids FEMA's Hurricane Maria Rescue Operation in Puerto Rico

NASA Image and Video Library

2017-09-26

The Advanced Rapid Imaging and Analysis (ARIA) team at NASA's Jet Propulsion Laboratory in Pasadena, California, and Caltech, also in Pasadena, created this Damage Proxy Map (DPM) depicting areas of Eastern Puerto Rico that are likely damaged (shown by red and yellow pixels) as a result of Hurricane Maria (a Category 4 hurricane at landfall in Puerto Rico on Sept. 20, 2017). The map is derived from synthetic aperture radar (SAR) images from the Copernicus Sentinel-1A and Sentinel-1B satellites, operated by the European Space Agency (ESA). The images were taken before (March 25, 2017) and after (Sept. 21, 2017) the storm's landfall. The map was delivered to responding agencies, including the Federal Emergency Management Agency (FEMA), on Sept. 22, 2017. FEMA combined the map with building infrastructure data to estimate a damage density map, which was sent to its Urban Search and Rescue teams in the field in Puerto Rico. The map covers an area of 105 by 60 miles (169 by 96 kilometers), shown by the large red polygon in the figure. The inset, denoted by the orange rectangle, shows the extent of damage in and around the capital city of San Juan. Each pixel measures about 98 feet (30 meters) across. The color variation from yellow to red indicates increasingly more significant ground surface change. Preliminary validation was done by comparing the map with anecdotal reports of damage. This damage proxy map should be used as guidance to identify damaged areas, and may be less reliable over vegetated and flooded areas. Sentinel-1 data were accessed through the Copernicus Open Access Hub. The image contains modified Copernicus Sentinel data (2017), processed by ESA and analyzed by the NASA-JPL/Caltech ARIA team. This research was carried out at JPL under a contract with NASA. https://photojournal.jpl.nasa.gov/catalog/PIA21964

Hydrogeologic aspects of the Knippa Gap area in eastern Uvalde and western Medina counties, Texas

USGS Publications Warehouse

Lambert, Rebecca B.; Clark, Allan K.; Pedraza, Diana E.; Morris, Robert R.

2014-01-01

The Edwards aquifer is the primary source of potable water for the San Antonio area in south-central Texas. The Knippa Gap area is a structural low (trough) postulated to channel or restrict flow in the Edwards aquifer in eastern Uvalde and western Medina Counties, Tex. To better understand the function of the Knippa Gap, the U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers, developed the first detailed surficial geologic map of the Knippa Gap area with data and information obtained from previous investigations and field observations. A simplified version of the detailed geologic map depicting the hydrologic units, faulting, and structural dips of the Knippa Gap area is provided in this fact sheet. The map shows that groundwater flow in the Edwards aquifer is influenced by the Balcones Fault Zone, a structurally complex area of the aquifer that contains relay ramps that have formed in extensional fault systems and allowed for deformational changes along fault blocks. Faulting in southeast Uvalde and southwest Medina Counties has produced relay-ramp structures that dip downgradient to the structural low (trough) of the Knippa Gap.

The influence of environmental and lithologic factors on rockfall at a regional scale: an evaluation using GIS

NASA Astrophysics Data System (ADS)

Menéndez Duarte, Rosana; Marquínez, Jorge

2002-02-01

Analysis of the spatial distribution of rockfall deposits at a regional scale (over an area of 250 km 2 of northern Spain) using a cartographic database supported by a Geographic Information System (GIS) reveals several relationships between rockfall activity and environmental variables. Recent rockfall activity is inferred when recent scree is preserved at the bottom of the rock slopes. In order to identify the slope source areas of the scree we have mapped the deposit's drainage basin, applying topographic criteria, and we have combined these basins with the rock slopes map. A method for setting the basin boundaries automatically will replace manual cartography. This method is based on algorithms available within many commercial software programs and originally planned to analyse the behaviour of fluids over a topographic surface. The results obtained by combining the rockfall area source map with the geology and DTM show the relationships between the distribution of rockfall deposits and lithology, elevation and slope of the rockwall and a strong control of the joint type and density. Elevation influence on rockfall has been associated with climatic variations with elevation. Other variables, such as orientation, show complex influences that are difficult to interpret.

The Sea-Floor Mapping Facility at the U.S. Geological Survey Woods Hole Field Center, Woods Hole, Massachusetts

USGS Publications Warehouse

Deusser, Rebecca E.; Schwab, William C.; Denny, Jane F.

2002-01-01

Researchers of the sea-floor mapping facility at the U.S. Geological Survey (USGS) Woods Hole Field Center in Woods Hole, Mass., use state-of-the-art technology to produce accurate geologic maps of the sea floor. In addition to basic bathymetry and morphology, sea-floor maps may contain information about the distribution of sand resources, patterns of coastal erosion, pathways of pollutant transport, and geologic controls on marine biological habitats. The maps may also show areas of human impacts, such as disturbance by bottom fishing and pollution caused by offshore waste disposal. The maps provide a framework for scientific research and provide critical information to decisionmakers who oversee resources in the coastal ocean.

Geologic map of MTM -40252 and -40257 quadrangles, Reull Vallis region of Mars

USGS Publications Warehouse

Mest, Scott C.; Crown, David A.

2002-01-01

Mars Transverse Mercator (MTM) quadrangles -40252 and -40257 cover a portion of the highlands of Promethei Terra northeast of the Hellas basin. The map area consists of heavily cratered ancient highland materials of moderate to high relief, isolated knobs and massifs of rugged mountainous materials, extensive tracts of smooth and channeled plains, and other surficial deposits. Reull Vallis, an approximately 1,500 km-long outflow channel system, cuts through the southeast corner of the map area. Regional slopes are to the southwest, toward the Hellas basin, as indicated by Martian topographic maps and the orientations of channels along the northeast rim of the Hellas basin. The Martian highlands cover more than 60 percent of the planet's surface and are primarily in the southern hemisphere. Most of the highlands consist of rugged, densely cratered terrains believed to represent the final phase of heavy bombardment in the inner solar system about 4.0 billion years ago. Parts of the Martian highlands show evidence of extensive degradation and modification. The map area shows landforms created by numerous geologic processes, including tectonism, fluvial activity, and mass wasting. The occurrence of fluvial features, such as outflow channels and valley networks, has significant implications for past Martian conditions. Determining the geology of the highlands northeast of the Hellas basin provides a better understanding of the role and timing of volatile-driven activity in the evolution of the highlands. Photogeologic mapping at 1:500,000 scale from analysis of Viking Orbiter images complements geomorphic studies of Reull Vallis and other highland outflow systems, of drainage networks, and of highland debris aprons and regional geologic mapping studies of the highlands at the 1:2,000,000 scale and 1:1,000,000 scale. Crater size-frequency distributions have been compiled to constrain the relative ages of geologic units and determine the timing and extents of the observed geologic processes.

Forest Biomass Mapping From Lidar and Radar Synergies

NASA Technical Reports Server (NTRS)

Sun, Guoqing; Ranson, K. Jon; Guo, Z.; Zhang, Z.; Montesano, P.; Kimes, D.

2011-01-01

The use of lidar and radar instruments to measure forest structure attributes such as height and biomass at global scales is being considered for a future Earth Observation satellite mission, DESDynI (Deformation, Ecosystem Structure, and Dynamics of Ice). Large footprint lidar makes a direct measurement of the heights of scatterers in the illuminated footprint and can yield accurate information about the vertical profile of the canopy within lidar footprint samples. Synthetic Aperture Radar (SAR) is known to sense the canopy volume, especially at longer wavelengths and provides image data. Methods for biomass mapping by a combination of lidar sampling and radar mapping need to be developed. In this study, several issues in this respect were investigated using aircraft borne lidar and SAR data in Howland, Maine, USA. The stepwise regression selected the height indices rh50 and rh75 of the Laser Vegetation Imaging Sensor (LVIS) data for predicting field measured biomass with a R(exp 2) of 0.71 and RMSE of 31.33 Mg/ha. The above-ground biomass map generated from this regression model was considered to represent the true biomass of the area and used as a reference map since no better biomass map exists for the area. Random samples were taken from the biomass map and the correlation between the sampled biomass and co-located SAR signature was studied. The best models were used to extend the biomass from lidar samples into all forested areas in the study area, which mimics a procedure that could be used for the future DESDYnI Mission. It was found that depending on the data types used (quad-pol or dual-pol) the SAR data can predict the lidar biomass samples with R2 of 0.63-0.71, RMSE of 32.0-28.2 Mg/ha up to biomass levels of 200-250 Mg/ha. The mean biomass of the study area calculated from the biomass maps generated by lidar- SAR synergy 63 was within 10% of the reference biomass map derived from LVIS data. The results from this study are preliminary, but do show the potential of the combined use of lidar samples and radar imagery for forest biomass mapping. Various issues regarding lidar/radar data synergies for biomass mapping are discussed in the paper.

Spatial point analysis based on dengue surveys at household level in central Brazil

PubMed Central

Siqueira-Junior, João B; Maciel, Ivan J; Barcellos, Christovam; Souza, Wayner V; Carvalho, Marilia S; Nascimento, Nazareth E; Oliveira, Renato M; Morais-Neto, Otaliba; Martelli, Celina MT

2008-01-01

Background Dengue virus (DENV) affects nonimunne human populations in tropical and subtropical regions. In the Americas, dengue has drastically increased in the last two decades and Brazil is considered one of the most affected countries. The high frequency of asymptomatic infection makes difficult to estimate prevalence of infection using registered cases and to locate high risk intra-urban area at population level. The goal of this spatial point analysis was to identify potential high-risk intra-urban areas of dengue, using data collected at household level from surveys. Methods Two household surveys took place in the city of Goiania (~1.1 million population), Central Brazil in the year 2001 and 2002. First survey screened 1,586 asymptomatic individuals older than 5 years of age. Second survey 2,906 asymptomatic volunteers, same age-groups, were selected by multistage sampling (census tracts; blocks; households) using available digital maps. Sera from participants were tested by dengue virus-specific IgM/IgG by EIA. A Generalized Additive Model (GAM) was used to detect the spatial varying risk over the region. Initially without any fixed covariates, to depict the overall risk map, followed by a model including the main covariates and the year, where the resulting maps show the risk associated with living place, controlled for the individual risk factors. This method has the advantage to generate smoothed risk factors maps, adjusted by socio-demographic covariates. Results The prevalence of antibody against dengue infection was 37.3% (95%CI [35.5–39.1]) in the year 2002; 7.8% increase in one-year interval. The spatial variation in risk of dengue infection significantly changed when comparing 2001 with 2002, (ORadjusted = 1.35; p < 0.001), while controlling for potential confounders using GAM model. Also increasing age and low education levels were associated with dengue infection. Conclusion This study showed spatial heterogeneity in the risk areas of dengue when using a spatial multivariate approach in a short time interval. Data from household surveys pointed out that low prevalence areas in 2001 surveys shifted to high-risk area in consecutive year. This mapping of dengue risks should give insights for control interventions in urban areas. PMID:18937868

Using simulated maps to interpret the geochemistry, formation and quality of the Blue Gem Coal Bed, Kentucky, USA

USGS Publications Warehouse

Geboy, Nicholas J.; Olea, Ricardo A.; Engle, Mark A.; Martin-Fernandez, Jose Antonio

2013-01-01

This study presents geostatistical simulations of coal-quality parameters, major oxides and trace metals for an area covering roughly 812 km2 of the Blue Gem coal bed in southeastern Kentucky, USA. The Blue Gem, characterized by low ash yield and low sulfur content, is an important economic resource. Past studies have characterized the Blue Gem's geochemistry, palynology and petrography and inferred a depositional setting of a planar peat deposit that transitioned to slightly domed later in its development. These studies have focused primarily on vertical geochemical trends within the coal bed. Simulated maps of chemical elements derived from 45 measured sample locations across the study area provide an opportunity to observe changes in the horizontal direction within the coal bed. As the Blue Gem coal bed shows significant vertical chemical trends, care was taken in this study to try to select samples from a single, middle portion of the coal. By revealing spatial distribution patterns of elements across the middle of the bed, associations between different components of the coal can be seen. The maps therefore help to provide a picture of the coal-forming peat bog at an instant in geologic time and allow interpretation of a depositional setting in the horizontal direction. Results from this middle portion of the coal suggest an association of SiO2 with both K2O and TiO2 in different parts of the study area. Further, a pocket in the southeast of the study area shows elevated concentrations of elements attributable to observed carbonate-phase minerals (MgO, CaO, Ba and Sr) as well as elements commonly associated with sulfide-phase minerals (Cu, Mo and Ni). Areas of relatively high ash yield are observed in the north and south of the mapped area, in contrast to the low ash yields seen towards the east. Additionally, we present joint probability maps where multiple coal-quality parameters are plotted simultaneously on one figure. This application allows researchers to investigate associations of more than two components in a straight-forward manner useful in guiding resource exploration.

Value of right ventricular mapping in patients with postinfarction ventricular tachycardia.

PubMed

Yokokawa, Miki; Good, Eric; Crawford, Thomas; Chugh, Aman; Pelosi, Frank; Latchamsetty, Rakesh; Oral, Hakan; Morady, Fred; Bogun, Frank

2012-06-01

Postinfarction ventricular tachycardia (VT) typically involves the left ventricular endocardium. Right ventricular involvement in the arrhythmogenic substrate of postinfarction VT is considered unusual. To assess the role of right ventricular mapping and ablation in patients with prior septal myocardial infarction. From among 37 consecutive patients with recurrent postinfarction VT, 18 patients with evidence of left ventricular septal involvement of myocardial infarction were identified; these patients were the subjects of this report. In these 18 patients, 166 VTs (cycle length 372 ± 117 ms) were induced. Right ventricular voltage mapping was performed in all 18 patients with left ventricular septal myocardial infarction. Right ventricular voltage mapping showed areas of low voltage in 11 patients; pace mapping from these areas revealed matching pace maps for 17 VTs, and radiofrequency ablation from the right ventricular endocardium but not the left ventricular endocardium eliminated 14 of 17 VTs. VTs with critical components in the right ventricle had a left bundle branch block morphology that had similar characteristics as left bundle branch block VTs with critical areas involving the left ventricular septum. Patients with right ventricular VT breakthrough sites had a lower ejection fraction than did patients without VT breaking out on the right ventricular septum (18% ± 5% vs 33% ± 15%; P = .01). Right ventricular mapping and ablation may be necessary in order to eliminate all inducible VTs in patients with postinfarction VT. More than half the patients with septal myocardial infarction have right ventricular septal areas that are critical for postinfarction VT and that cannot be eliminated by left ventricular ablation alone. Copyright © 2012 Heart Rhythm Society. All rights reserved.

Potentiometric Surface of the Magothy Aquifer in Southern Maryland, September 2007

USGS Publications Warehouse

Curtin, Stephen E.; Andreasen, David C.; Staley, Andrew W.

2009-01-01

This report presents a map showing the potentiometric surface of the Magothy aquifer in the Magothy Formation of Late Cretaceous age in Southern Maryland during September 2007. The map is based on water-level measurements in 69 wells. The highest measured water level was 85 feet above sea level near the northern boundary and outcrop area of the aquifer in the north-central part of Anne Arundel County. The potentiometric surface declined towards the south. Local gradients were directed toward the center of a cone of depression in the Waldorf area that developed in response to pumping. Measured ground-water levels were as low as 90 feet below sea level in the Waldorf area.

Geologic map of Chickasaw National Recreation Area, Murray County, Oklahoma

USGS Publications Warehouse

Blome, Charles D.; Lidke, David J.; Wahl, Ronald R.; Golab, James A.

2013-01-01

This 1:24,000-scale geologic map is a compilation of previous geologic maps and new geologic mapping of areas in and around Chickasaw National Recreation Area. The geologic map includes revisions of numerous unit contacts and faults and a number of previously “undifferentiated” rock units were subdivided in some areas. Numerous circular-shaped hills in and around Chickasaw National Recreation Area are probably the result of karst-related collapse and may represent the erosional remnants of large, exhumed sinkholes. Geospatial registration of existing, smaller scale (1:72,000- and 1:100,000-scale) geologic maps of the area and construction of an accurate Geographic Information System (GIS) database preceded 2 years of fieldwork wherein previously mapped geology (unit contacts and faults) was verified and new geologic mapping was carried out. The geologic map of Chickasaw National Recreation Area and this pamphlet include information pertaining to how the geologic units and structural features in the map area relate to the formation of the northern Arbuckle Mountains and its Arbuckle-Simpson aquifer. The development of an accurate geospatial GIS database and the use of a handheld computer in the field greatly increased both the accuracy and efficiency in producing the 1:24,000-scale geologic map.

Investigations using data from LANDSAT-2

NASA Technical Reports Server (NTRS)

Hossain, A. (Principal Investigator)

1977-01-01

The author has identified the following significant results. LANDSAT imageries of Mirpur area of Dacca district were used in connection with surveys for black plastic clay. The imageries showed the broad pattern of small valleys cutting into Madhupur clay. Land use maps of Haor areas of Sylhet and Mymensingh districts were prepared. As a test case, two thana areas, namely Nickley and Astogram, were classified in different categories such as crop, settlement, and water. It does not show much agreement with the Agriculture Dept.'s statistics.

Structure and shale gas production patterns from eastern Kentucky field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shumaker, R.C.

Computer-derived subsurface structure, isopach, and gas-flow maps, based on 4000 drillers logs, have been generated for eastern Kentucky under a project sponsored by the Gas Research Institute. Structure maps show low-relief flextures related to basement structure. Some structures have been mapped at the surface, others have not. Highest final open-flow (fof) of shale gas from wells in Martin County follow a structural low between (basement) anticlines. From there, elevated gas flows (fof) extend westward along the Warfield monocline to Floyd County where the high flow (fof) trend extends southward along the Floyd County channel. In Knott County, the number ofmore » wells with high gas flow (fof) decreases abruptly. The center of highest gas flow (fof) in Floyd County spreads eastward to Pike County, forming a triangular shaped area of high production (fof). The center of highest gas flow (fof) is in an area where possible (basement) structure trends intersect and where low-relief surface folds (probably detached structure) were mapped and shown on the 1922 version of the Floyd County structure map. Modern regional maps, based on geophysical logs from widely spaced wells, do not define the low-relief structures that have been useful in predicting gas flow trends. Detailed maps based on drillers logs can be misleading unless carefully edited. Comparative analysis of high gas flows (fof) and 10-year cumulative production figures in a small area confirms that there is a relationship between gas flow (fof) values and long-term cumulative production.« less

Cell Based Associations: A procedure for considering scarce and mixed mineral occurrences in predictive mapping

NASA Astrophysics Data System (ADS)

Tourlière, Bruno; Pakyuz-Charrier, Evren; Cassard, Daniel; Barbanson, Luc; Gumiaux, Charles

2015-05-01

Cell Based Association is an innovative mineral favorability procedure designed to answer special needs of the mining industry in data wise critical situations where usual favorability methods may not yield satisfactory results. Those situations relate to input data quality (e.g. clustered points, mixed and scarce data, approximate location) or some assumptions that are considered unreasonable (e.g. map areas relevance, conditional independence). The principle of CBA consists in replacing polygons of geological units with a square cell grid (hence the 'cell-based'). Each cell contains a range of units ('association') that are binary coded in terms of their presence (1) or absence (0) within study area. The loss of resolution inherent to this procedure is compensated by the enriched information contained in each cell owing to the notion of (lithological) association. Lithological associations are considered as binary spectra and as such are classified using Ascendant Hierarchical Clustering (AHC) thus obtaining a synthetic map of lithological associations. The prospectivity map shows as favourable the cells of the same AHC classes that the ones including mineral occurrences. It was observed that CBA can distinguish between different ore deposit varieties from a blended mineral occurrences data set. CBA can theoretically include any spatialized data (e.g. geophysics, structural data) as an extra variable to specify classification and narrow favourable areas. Doing so would make it an independent favorability mapping procedure and is still under development. Cell size in a grid is a critical parameter of the procedure; it must be compatible with the looked-for phenomena and should have a sufficient lithological variability. In addition to its use for producing favorability maps, a CBA-derived map could help in understanding the background information contained in geological maps. CBA can also be applied to other fields, such as agriculture and urban planning. Modelling of mineral prospectivity is a regional- or district scale mapping activity, whether field based or GIS based, which aims to delineate prospective areas for further exploration at the next higher scales of mapping. Notwithstanding the scale of mapping, mineral prospectivity is related to the degrees of presence and degrees of importance of individual pieces of spatial evidence of occurrence of mineral deposits of the type sought. That is, in a region or district under investigation, if there are more important pieces of spatial evidence in an area than in another area, then the former is considered to have higher prospectivity than the latter".

Areas with Surface Thermal Anomalies as Detected by ASTER and LANDSAT Data around Pinkerton Hot Springs, Colorado

DOE Data Explorer

Khalid Hussein

2012-02-01

This map shows areas of anomalous surface temperature in northern Saguache Counties identified from ASTER and LANDSAT thermal data and spatial based insolation model. The temperature for the ASTER data was calculated using the Emissivity Normalization Algorithm that separate temperature from emissivity. The incoming solar radiation was calculated using spatial based insolation model developed by Fu and Rich (1999). Then the temperature due to solar radiation was calculated using emissivity derived from ASTER data. The residual temperature, i.e. temperature due to solar radiation subtracted from ASTER temperature was used to identify thermally anomalous areas. Areas having anomalous temperature in the ASTER data are shown in blue diagonal hatch, while areas having anomalous temperature in the LANDSAT data are shown in magenta on the map. Thermal springs and areas with favorable geochemistry are also shown. Springs or wells having non-favorable geochemistry are shown as blue dots.

Areas with Surface Thermal Anomalies as Detected by ASTER and LANDSAT Data in Northwest Delta, Colorado

DOE Data Explorer

Khalid Hussein

2012-02-01

This map shows areas of anomalous surface temperature in northern Saguache Counties identified from ASTER and LANDSAT thermal data and spatial based insolation model. The temperature for the ASTER data was calculated using the Emissivity Normalization Algorithm that separate temperature from emissivity. The incoming solar radiation was calculated using spatial based insolation model developed by Fu and Rich (1999). Then the temperature due to solar radiation was calculated using emissivity derived from ASTER data. The residual temperature, i.e. temperature due to solar radiation subtracted from ASTER temperature was used to identify thermally anomalous areas. Areas having anomalous temperature in the ASTER data are shown in blue diagonal hatch, while areas having anomalous temperature in the LANDSAT data are shown in magenta on the map. Thermal springs and areas with favorable geochemistry are also shown. Springs or wells having non-favorable geochemistry are shown as blue dots.

Areas with Surface Thermal Anomalies as Detected by ASTER and LANDSAT Data in Ouray, Colorado

DOE Data Explorer

Khalid Hussein

2012-02-01

This map shows areas of anomalous surface temperature in Ouray identified from ASTER and LANDSAT thermal data and spatial based insolation model. The temperature for the ASTER data was calculated using the Emissivity Normalization Algorithm that separate temperature from emissivity. The incoming solar radiation was calculated using spatial based insolation model developed by Fu and Rich (1999). Then the temperature due to solar radiation was calculated using emissivity derived from ASTER data. The residual temperature, i.e. temperature due to solar radiation subtracted from ASTER temperature was used to identify thermally anomalous areas. Areas having anomalous temperature in the ASTER data are shown in blue diagonal hatch, while areas having anomalous temperature in the LANDSAT data are shown in magenta on the map. Thermal springs and areas with favorable geochemistry are also shown. Springs or wells having non-favorable geochemistry are shown as blue dots.

Areas with Surface Thermal Anomalies as Detected by ASTER and LANDSAT Data in Southwest Steamboat Springs, Garfield County, Colorado

DOE Data Explorer

Khalid Hussein

2012-02-01

This map shows areas of anomalous surface temperature around south Steamboat Springs as identified from ASTER and LANDSAT thermal data and spatial based insolation model. The temperature for the ASTER data was calculated using the Emissivity Normalization Algorithm that separate temperature from emissivity. The incoming solar radiation was calculated using spatial based insolation model developed by Fu and Rich (1999). Then the temperature due to solar radiation was calculated using emissivity derived from ASTER data. The residual temperature, i.e. temperature due to solar radiation subtracted from ASTER temperature was used to identify thermally anomalous areas. Areas having anomalous temperature in the ASTER data are shown in blue diagonal hatch, while areas having anomalous temperature in the LANDSAT data are shown in magenta on the map. Thermal springs and areas with favorable geochemistry are also shown. Springs or wells having non-favorable geochemistry are shown as blue dots.

Areas with Surface Thermal Anomalies as Detected by ASTER and LANDSAT Data in Northern Saguache County, Colorado

DOE Data Explorer

Khalid Hussein

2012-02-01

This map shows areas of anomalous surface temperature in northern Saguache Counties identified from ASTER and LANDSAT thermal data and spatial based insolation model. The temperature for the ASTER data was calculated using the Emissivity Normalization Algorithm that separate temperature from emissivity. The incoming solar radiation was calculated using spatial based insolation model developed by Fu and Rich (1999). Then the temperature due to solar radiation was calculated using emissivity derived from ASTER data. The residual temperature, i.e. temperature due to solar radiation subtracted from ASTER temperature was used to identify thermally anomalous areas. Areas having anomalous temperature in the ASTER data are shown in blue diagonal hatch, while areas having anomalous temperature in the LANDSAT data are shown in magenta on the map. Thermal springs and areas with favorable geochemistry are also shown. Springs or wells having non-favorable geochemistry are shown as blue dots.

Mapping the distribution of mangrove species in the Core Zone of Mai Po Marshes Nature Reserve, Hong Kong, using hyperspectral data and high-resolution data

NASA Astrophysics Data System (ADS)

Jia, Mingming; Zhang, Yuanzhi; Wang, Zongming; Song, Kaishan; Ren, Chunying

2014-12-01

Mangrove species compositions and distributions are essential for conservation and restoration efforts. In this study, hyperspectral data of EO-1 HYPERION sensor and high spatial resolution data of SPOT-5 sensor were used in Mai Po mangrove species mapping. Objected-oriented method was used in mangrove species classification processing. Firstly, mangrove objects were obtained via segmenting high spatial resolution data of SPOT-5. Then the objects were classified into different mangrove species based on the spectral differences of HYPERION image. The classification result showed that in the top canopy, Kandelia obovata and Avicennia marina dominated Mai Po Marshes Natural Reserve, with area of 196.8 ha and 110.8 ha, respectively, Acanthus ilicifolius and Aegiceras corniculatum were mixed together and living at the edge of channels with an area of 11.7 ha. Additionally, mangrove species shows clearly zonations and associations in the Mai Po Core Zone. The overall accuracy of our mangrove map was 88% and the Kappa confidence was 0.83, which indicated great potential of using hyperspectral and high-resolution data for distinguishing and mapping mangrove species.

Flood-inundation maps for the Susquehanna River near Harrisburg, Pennsylvania, 2013

USGS Publications Warehouse

Roland, Mark A.; Underwood, Stacey M.; Thomas, Craig M.; Miller, Jason F.; Pratt, Benjamin A.; Hogan, Laurie G.; Wnek, Patricia A.

2014-01-01

A series of 28 digital flood-inundation maps was developed for an approximate 25-mile reach of the Susquehanna River in the vicinity of Harrisburg, Pennsylvania. The study was selected by the U.S. Army Corps of Engineers (USACE) national Silver Jackets program, which supports interagency teams at the state level to coordinate and collaborate on flood-risk management. This study to produce flood-inundation maps was the result of a collaborative effort between the USACE, National Weather Service (NWS), Susquehanna River Basin Commission (SRBC), The Harrisburg Authority, and the U.S. Geological Survey (USGS). These maps are accessible through Web-mapping applications associated with the NWS, SRBC, and USGS. The maps can be used in conjunction with the real-time stage data from the USGS streamgage 01570500, Susquehanna River at Harrisburg, Pa., and NWS flood-stage forecasts to help guide the general public in taking individual safety precautions and will provide local municipal officials with a tool to efficiently manage emergency flood operations and flood mitigation efforts. The maps were developed using the USACE HEC–RAS and HEC–GeoRAS programs to compute water-surface profiles and to delineate estimated flood-inundation areas for selected stream stages. The maps show estimated flood-inundation areas overlaid on high-resolution, georeferenced, aerial photographs of the study area for stream stages at 1-foot intervals between 11 feet and 37 feet (which include NWS flood categories Action, Flood, Moderate, and Major) and the June 24, 1972, peak-of-record flood event at a stage of 33.27 feet at the Susquehanna River at Harrisburg, Pa., streamgage.

Preliminary applications of Landsat images and aerial photography for determining land-use, geologic, and hydrologic characteristics, Yampa River basin, Colorado and Wyoming

USGS Publications Warehouse

Heimes, F.J.; Moore, G.K.; Steele, T.D.

1978-01-01

Expanded energy- and recreation-related activities in the Yampa River basin, Colorado and Wyoming, have caused a rapid increase in economic development which will result in increased demand and competition for natural resources. In planning for efficient allocation of the basin 's natural resources, Landsat images and small-scale color and color-infrared photographs were used for selected geologic, hydrologic and land-use applications within the Yampa River basin. Applications of Landsat data included: (1) regional land-use classification and mapping, (2) lineament mapping, and (3) areal snow-cover mapping. Results from the Landsat investigations indicated that: (1) Landsat land-use classification maps, at a regional level, compared favorably with areal land-use patterns that were defined from available ground information, (2) lineaments were mapped in sufficient detail using recently developed techniques for interpreting aerial photographs, (3) snow cover generally could be mapped for large areas with the exception of some densely forested areas of the basin and areas having a large percentage of winter-season cloud cover. Aerial photographs were used for estimation of turbidity for eight stream locations in the basin. Spectral reflectance values obtained by digitizing photographs were compared with measured turbidity values. Results showed strong correlations (variances explained of greater than 90 percent) between spectral reflectance obtained from color photographs and measured turbidity values. (Woodard-USGS)

Cortical connective field estimates from resting state fMRI activity.

PubMed

Gravel, Nicolás; Harvey, Ben; Nordhjem, Barbara; Haak, Koen V; Dumoulin, Serge O; Renken, Remco; Curčić-Blake, Branislava; Cornelissen, Frans W

2014-01-01

One way to study connectivity in visual cortical areas is by examining spontaneous neural activity. In the absence of visual input, such activity remains shaped by the underlying neural architecture and, presumably, may still reflect visuotopic organization. Here, we applied population connective field (CF) modeling to estimate the spatial profile of functional connectivity in the early visual cortex during resting state functional magnetic resonance imaging (RS-fMRI). This model-based analysis estimates the spatial integration between blood-oxygen level dependent (BOLD) signals in distinct cortical visual field maps using fMRI. Just as population receptive field (pRF) mapping predicts the collective neural activity in a voxel as a function of response selectivity to stimulus position in visual space, CF modeling predicts the activity of voxels in one visual area as a function of the aggregate activity in voxels in another visual area. In combination with pRF mapping, CF locations on the cortical surface can be interpreted in visual space, thus enabling reconstruction of visuotopic maps from resting state data. We demonstrate that V1 ➤ V2 and V1 ➤ V3 CF maps estimated from resting state fMRI data show visuotopic organization. Therefore, we conclude that-despite some variability in CF estimates between RS scans-neural properties such as CF maps and CF size can be derived from resting state data.

A spatial database of bedding attitudes to accompany Geologic map of the greater Denver area, Front Range Urban Corridor, Colorado

USGS Publications Warehouse

Trimble, Donald E.; Machette, Michael N.; Brandt, Theodore R.; Moore, David W.; Murray, Kyle E.

2003-01-01

This digital map shows bedding attitude symbols display over the geographic extent of surficial deposits and rock stratigraphic units (formations) as compiled by Trimble and Machette 1973-1977 and published in 1979 (U.S. Geological Survey Map I-856-H) under the Front Range Urban Corridor Geology Program. Trimble and Machette compiled their geologic map from published geologic maps and unpublished geologic mapping having varied map unit schemes. A convenient feature of the compiled map is its uniform classification of geologic units that mostly matches those of companion maps to the north (USGS I-855-G) and to the south (USGS I-857-F). Published as a color paper map, the Trimble and Machette map was intended for land-use planning in the Front Range Urban Corridor. This map recently (1997-1999), was digitized under the USGS Front Range Infrastructure Resources Project (see cross-reference). In general, the mountainous areas in the west part of the map exhibit various igneous and metamorphic bedrock units of Precambrian age, major faults, and fault brecciation zones at the east margin (5-20 km wide) of the Front Range. The eastern and central parts of the map (Colorado Piedmont) depict a mantle of unconsolidated deposits of Quaternary age and interspersed outcroppings of Cretaceous or Tertiary-Cretaceous sedimentary bedrock. The Quaternary mantle is comprised of eolian deposits (quartz sand and silt), alluvium (gravel, sand, and silt of variable composition), colluvium, and few landslides. At the mountain front, north-trending, dipping Paleozoic and Mesozoic sandstone, shale, and limestone bedrock formations form hogbacks and intervening valleys.

Natural and Man-Made Hazards in the Cayman Islands

NASA Astrophysics Data System (ADS)

Novelo-Casanova, D. A.; Suarez, G.

2010-12-01

Located in the western Caribbean Sea to the northwest of Jamaica, the Cayman Islands are a British overseas territory comprised of three islands: Grand Cayman, Cayman Brac, and Little Cayman. These three islands occupy around 250 km2 of land area. In this work, historical and recent data were collected and classified to identify and rank the natural and man-made hazards that may potentially affect the Cayman Islands and determine the level of exposure of Grand Cayman to these events. With this purpose, we used the vulnerability assessment methodology developed by the North Caroline Department of Environment and Natural Resources. The different degrees of physical vulnerability for each hazard were graphically interpreted with the aid of maps using a relative scoring system. Spatial maps were generated showing the areas of different levels of exposure to multi-hazards. The more important natural hazard to which the Cayman Islands are exposed is clearly hurricanes. To a lesser degree, the islands may be occasionally exposed to earthquakes and tsunamis. Explosions or leaks of the Airport Texaco Fuel Depot and the fuel pipeline at Grand Cayman are the most significant man-made hazards. Our results indicate that there are four areas in Grand Cayman with various levels of exposure to natural and man-made hazards: The North Sound, Little Sound and Eastern West Bay (Area 1) show a very high level of exposure; The Central Mangroves, Central Bodden Town, Central George Town and the West Bay (Area 2) have high level of exposure; The Northwestern West Bay, Western Georgetown-Bodden Town, and East End-North Side (Area 3) are under moderate levels of exposure. The remainder of the island shows low exposure (Area 4). It is important to underline that this study presents a first evaluation of the main natural and man-made hazards that may affect the Cayman Islands. The maps generated will be useful tools for emergency managers and policy developers and will increase the overall awareness of decision makers for disasters prevention and mitigation plans. Our results constitute the basis of future mitigation risk projects in the islands. Areas showing the level of exposure to natural and man-made hazards at Grand Cayman.

The difference between the potentiometric surfaces of the Upper Patapsco aquifer in southern Maryland, September 1990 and September 2009

USGS Publications Warehouse

Curtin, Stephen E.; Andreasen, David C.; Staley, Andrew W.

2010-01-01

This report presents a map showing the change in the potentiometric surface of the upper Patapsco aquifer in the Patapsco Formation of Early Cretaceous age in Southern Maryland between September 1990 and September 2009. The map, based on water level differences obtained from 33 wells, shows that during the 19-year period, the change in the potentiometric surface ranged from zero at the edge of the outcrop area in northern Anne Arundel County to a decline of 20 feet at Broad Creek, 16 feet near Arnold, 32 feet at Waldorf, 37 feet at the Chalk Point power plant, and 43 feet at Lexington Park. The map also shows well yield in gallons per day for 2008 at wells or well fields.

The aluminum phosphate zone in the Peace River area, land-pebble phosphate field, Florida

USGS Publications Warehouse

Cathcart, James B.

1953-01-01

The Peace River area, comprising T. 30 and 31 S., R. 24 and 25 E., contains a thicker and more persistent aluminum phosphate zone, and one that is higher in P2O5 and uranium content than is known elsewhere in the land-pebble phosphate district. This report has been prepared to bring together all of the information on the aluminum phosphate zone in the area where the first plant to treat this material will probably be located. The area may be divided into three physiographic units, (1) the ridge, (2) the flatwoods, and (3) the valley. Maps showing distribution and grade of the aluminum phosphate zone indicate that the zone is thin or absent in the ridge unit, thickest and most persistent, and of the best grade in P2O5 and uranium in the flatwoods unit, and absent or very low in grade in the valley unit. Maps of thickness and of chemical composition show that even in favorable areas there are places where the aluminum phosphate zone is missing or of questionable economic importance. The distribution maps also show that areas of high P2O5 and high uranium content coincide closely. Areas containing thick aluminum phosphate material usually have high uranium and P2O5 contents. It is estimated that an average of 13,000 tons per day of aluminum phosphate material might be mined from this area. This figure is based on the probable amount of time, per year, that mining would be in favorable ground. When all mines in the area are in favorable ground, the tonnage per day might be about 23,000 tons. Tonnages of aluminum phosphate material have been computed for about 36 percent of the area of T. 30 S., R. 25 E., and for 18 percent of the area of T. 31 S., R. 25 E. The total inferred tonnage is about 150,000,000 short tons, with an average grade of 0.012 percent U3O8.

The Research and Compilation of City Maps in the National Geomatics Atlas of the PEOPLE'S Republic of China

NASA Astrophysics Data System (ADS)

Wang, G.; Wang, D.; Zhou, W.; Chen, M.; Zhao, T.

2018-04-01

The research and compilation of new century version of the National Huge Atlas of the People's Republic of China is the special basic work project by Ministry of Science and Technology of the People's Republic of China. Among them, the research and compilation of the National Geomatics Atlas of the People's Republic of China is its main content. The National Geomatics Atlas of China consists of 4 groups of maps and place name index. The 4 groups of maps are separately nationwide thematic map group, provincial fundamental geographical map group, landcover map group and city map group. The city map group is an important component part of the National Geomatics Atlas of China and mainly shows the process of urbanization in China. This paper, aim at design and compilation of 39 city-wide maps, briefly introduces mapping area research and scale design, mapping technical route, content selection and cartographic generalization, symbol design and visualization of map, etc.

Assessment of groundwater vulnerability in the coastal region of Oman using DRASTIC index method in GIS environment.

PubMed

Jamrah, Ahmad; Al-Futaisi, Ahmed; Rajmohan, Natarajan; Al-Yaroubi, Saif

2008-12-01

A study was carried out to develop a vulnerability map for Barka region in the North Batina of Oman using DRASTIC vulnerability index method in GIS environment. DRASTIC layers were created using data from published reports and the seven DRASTIC layers were processed by the ArcGIS geographic information system. Finally, DRASTIC maps were created for 1995 and 2004 to understand the long-term changes in the vulnerability index. DRASTIC vulnerability maps were evaluated using groundwater quality data such as chemical and biological parameters. DRASTIC vulnerability maps of 1995 and 2004 indicate that the northern part of Barka is more vulnerable to pollution than southern part and the central part of Barka also shows high relative vulnerability which is mostly related to the high conductivity values. Moreover, the changes in water level due to high abstraction rate of groundwater reflect in the vulnerability maps and low vulnerability area is increased in the southern part during 2004 compared to 1995. Moreover, regional distribution maps of nitrate, chloride and total and fecal coliforms are well correlated with DRASTIC vulnerability maps. In contrast to this, even though DRASTIC method predicted the central part of the study region is highly vulnerable, both chemical and biological parameters show lower concentrations in this region compared to coastal belt, which is mainly due to agricultural and urban development. In Barka, urban development and agricultural activities are very high in coastal region compared to southern and central part of the study area. Hence, this study concluded that DRASTIC method is also applicable in coastal region having ubiquitous contamination sources.

[Functional mapping using subdural electrodes combined with monitoring during awake craniotomy enabled preservation of function and extensive resection of a glioma adjacent to the parietal lobe language sites: a case report].

PubMed

Takebayashi, Kento; Saito, Taiichi; Nitta, Masayuki; Tamura, Manabu; Maruyama, Takashi; Muragaki, Yoshihiro; Okada, Yoshikazu

2015-01-01

Surgical resection of gliomas located in the dominant parietal lobe is difficult because this lesion is surrounded by multiple functional areas. Although functional mapping during awake craniotomy is very useful for resection of gliomas adjacent to eloquent areas, the limited time available makes it difficult to sufficiently evaluate multiple functions, such as language, calculative ability, distinction of right and left sides, and finger recognition. Here, we report a case of anaplastic oligodendroglioma, which was successfully treated with a combination of functional mapping using subdural electrodes and monitoring under awake craniotomy for glioma. A 32-year-old man presented with generalized seizure. Magnetic resonance imaging revealed a non-enhanced tumor in the left angular and supramarginal gyri. In addition, the tumor showed high accumulation on 11C-methionine positron emission tomography(PET)(tumor/normal brain tissue ratio=3.20). Preparatory mapping using subdural electrodes showed absence of brain function on the tumor lesion. Surgical removal was performed using cortical mapping during awake craniotomy with an updated navigation system using intraoperative magnetic resonance imaging(MRI). The tumor was resected until aphasia was detected by functional monitoring, and the extent of tumor resection was 93%. The patient showed transient transcortical aphasia and Gerstmann's syndrome after surgery but eventually recovered. The pathological diagnosis was anaplastic oligodendroglioma, and the patient was administered chemo-radiotherapy. The patient has been progression free for more than 2 years. The combination of subdural electrode mapping and monitoring during awake craniotomy is useful in order to achieve preservation of function and extensive resection for gliomas in the dominant parietal lobe.

National-scale cropland mapping based on spectral-temporal features and outdated land cover information.

PubMed

Waldner, François; Hansen, Matthew C; Potapov, Peter V; Löw, Fabian; Newby, Terence; Ferreira, Stefanus; Defourny, Pierre

2017-01-01

The lack of sufficient ground truth data has always constrained supervised learning, thereby hindering the generation of up-to-date satellite-derived thematic maps. This is all the more true for those applications requiring frequent updates over large areas such as cropland mapping. Therefore, we present a method enabling the automated production of spatially consistent cropland maps at the national scale, based on spectral-temporal features and outdated land cover information. Following an unsupervised approach, this method extracts reliable calibration pixels based on their labels in the outdated map and their spectral signatures. To ensure spatial consistency and coherence in the map, we first propose to generate seamless input images by normalizing the time series and deriving spectral-temporal features that target salient cropland characteristics. Second, we reduce the spatial variability of the class signatures by stratifying the country and by classifying each stratum independently. Finally, we remove speckle with a weighted majority filter accounting for per-pixel classification confidence. Capitalizing on a wall-to-wall validation data set, the method was tested in South Africa using a 16-year old land cover map and multi-sensor Landsat time series. The overall accuracy of the resulting cropland map reached 92%. A spatially explicit validation revealed large variations across the country and suggests that intensive grain-growing areas were better characterized than smallholder farming systems. Informative features in the classification process vary from one stratum to another but features targeting the minimum of vegetation as well as short-wave infrared features were consistently important throughout the country. Overall, the approach showed potential for routinely delivering consistent cropland maps over large areas as required for operational crop monitoring.

Ningaloo Reef: Shallow Marine Habitats Mapped Using a Hyperspectral Sensor

PubMed Central

Kobryn, Halina T.; Wouters, Kristin; Beckley, Lynnath E.; Heege, Thomas

2013-01-01

Research, monitoring and management of large marine protected areas require detailed and up-to-date habitat maps. Ningaloo Marine Park (including the Muiron Islands) in north-western Australia (stretching across three degrees of latitude) was mapped to 20 m depth using HyMap airborne hyperspectral imagery (125 bands) at 3.5 m resolution across the 762 km2 of reef environment between the shoreline and reef slope. The imagery was corrected for atmospheric, air-water interface and water column influences to retrieve bottom reflectance and bathymetry using the physics-based Modular Inversion and Processing System. Using field-validated, image-derived spectra from a representative range of cover types, the classification combined a semi-automated, pixel-based approach with fuzzy logic and derivative techniques. Five thematic classification levels for benthic cover (with probability maps) were generated with varying degrees of detail, ranging from a basic one with three classes (biotic, abiotic and mixed) to the most detailed with 46 classes. The latter consisted of all abiotic and biotic seabed components and hard coral growth forms in dominant or mixed states. The overall accuracy of mapping for the most detailed maps was 70% for the highest classification level. Macro-algal communities formed most of the benthic cover, while hard and soft corals represented only about 7% of the mapped area (58.6 km2). Dense tabulate coral was the largest coral mosaic type (37% of all corals) and the rest of the corals were a mix of tabulate, digitate, massive and soft corals. Our results show that for this shallow, fringing reef environment situated in the arid tropics, hyperspectral remote sensing techniques can offer an efficient and cost-effective approach to mapping and monitoring reef habitats over large, remote and inaccessible areas. PMID:23922921

Rapid and minimum invasive functional brain mapping by real-time visualization of high gamma activity during awake craniotomy.

PubMed

Ogawa, Hiroshi; Kamada, Kyousuke; Kapeller, Christoph; Hiroshima, Satoru; Prueckl, Robert; Guger, Christoph

2014-11-01

Electrocortical stimulation (ECS) is the gold standard for functional brain mapping during an awake craniotomy. The critical issue is to set aside enough time to identify eloquent cortices by ECS. High gamma activity (HGA) ranging between 80 and 120 Hz on electrocorticogram is assumed to reflect localized cortical processing. In this report, we used real-time HGA mapping and functional neuronavigation integrated with functional magnetic resonance imaging (fMRI) for rapid and reliable identification of motor and language functions. Four patients with intra-axial tumors in their dominant hemisphere underwent preoperative fMRI and lesion resection with an awake craniotomy. All patients showed significant fMRI activation evoked by motor and language tasks. During the craniotomy, we recorded electrocorticogram activity by placing subdural grids directly on the exposed brain surface. Each patient performed motor and language tasks and demonstrated real-time HGA dynamics in hand motor areas and parts of the inferior frontal gyrus. Sensitivity and specificity of HGA mapping were 100% compared with ECS mapping in the frontal lobe, which suggested HGA mapping precisely indicated eloquent cortices. We found different HGA dynamics of language tasks in frontal and temporal regions. Specificities of the motor and language-fMRI did not reach 85%. The results of HGA mapping was mostly consistent with those of ECS mapping, although fMRI tended to overestimate functional areas. This novel technique enables rapid and accurate identification of motor and frontal language areas. Furthermore, real-time HGA mapping sheds light on underlying physiological mechanisms related to human brain functions. Copyright © 2014 Elsevier Inc. All rights reserved.

National-scale cropland mapping based on spectral-temporal features and outdated land cover information

PubMed Central

Hansen, Matthew C.; Potapov, Peter V.; Löw, Fabian; Newby, Terence; Ferreira, Stefanus; Defourny, Pierre

2017-01-01

The lack of sufficient ground truth data has always constrained supervised learning, thereby hindering the generation of up-to-date satellite-derived thematic maps. This is all the more true for those applications requiring frequent updates over large areas such as cropland mapping. Therefore, we present a method enabling the automated production of spatially consistent cropland maps at the national scale, based on spectral-temporal features and outdated land cover information. Following an unsupervised approach, this method extracts reliable calibration pixels based on their labels in the outdated map and their spectral signatures. To ensure spatial consistency and coherence in the map, we first propose to generate seamless input images by normalizing the time series and deriving spectral-temporal features that target salient cropland characteristics. Second, we reduce the spatial variability of the class signatures by stratifying the country and by classifying each stratum independently. Finally, we remove speckle with a weighted majority filter accounting for per-pixel classification confidence. Capitalizing on a wall-to-wall validation data set, the method was tested in South Africa using a 16-year old land cover map and multi-sensor Landsat time series. The overall accuracy of the resulting cropland map reached 92%. A spatially explicit validation revealed large variations across the country and suggests that intensive grain-growing areas were better characterized than smallholder farming systems. Informative features in the classification process vary from one stratum to another but features targeting the minimum of vegetation as well as short-wave infrared features were consistently important throughout the country. Overall, the approach showed potential for routinely delivering consistent cropland maps over large areas as required for operational crop monitoring. PMID:28817618

Quantitative validation of sensory mapping in persistent postherniorrhaphy inguinal pain patients undergoing triple neurectomy.

PubMed

Bjurström, M F; Álvarez, R; Nicol, A L; Olmstead, R; Amid, P K; Chen, D C

2017-04-01

Neurectomy of the inguinal nerves may be considered for selected refractory cases of chronic postherniorrhaphy inguinal pain (CPIP). There is to date a paucity of easily applicable clinical tools to identify neuropathic pain and examine the neurosensory effects of remedial surgery. The present quantitative sensory testing (QST) pilot study evaluates a sensory mapping technique. Longitudinal (preoperative, immediate postoperative, and late postoperative) dermatomal sensory mapping and a comprehensive QST protocol were conducted in CPIP patients with unilateral, predominantly neuropathic inguinodynia presenting for triple neurectomy (n = 13). QST was conducted in four areas on the affected, painful side and in one contralateral comparison site. QST variables were compared according to sensory mapping outcomes: (o)/normal sensation, (+)/pain, and (-)/numbness. Diagnostic ability of the sensory mapping outcomes to detect QST-assessed allodynia or hypoesthesia was estimated through calculation of specificity and sensitivity values. Preoperatively, patients exhibited mechanical hypoesthesia and allodynia and pressure allodynia and hyperalgesia in painful areas mapped (+) (p < .05); sensory mapping outcome (+) demonstrated high ability to detect mechanical allodynia [sensitivity 0.74 (95% CI 0.61-0.86), specificity 0.94 (0.84-1.00)] and pressure allodynia [sensitivity 0.96 (0.89-1.00), specificity 1.00 (1.00-1.00)], but not thermal allodynia. Postoperatively, mapped areas of numbness (-) were associated with mechanical and thermal hypoesthesia (p < .05); (-) showed high sensitivity and specificity to detect mechanical and cold hypoesthesia. Sensory mapping provides an accurate clinical neuropathic assessment with strong correlation to QST findings of preoperative mechanical and pressure allodynia, and postoperative mechanical and thermal hypoesthesia in CPIP patients undergoing neurectomy.

Cumulative impacts of oil fields on northern Alaskan landscapes

USGS Publications Warehouse

Walker, D.A.; Webber, P.J.; Binnian, Emily F.; Everett, K.R.; Lederer, N.D.; Nordstrand, E.A.; Walker, M.D.

1987-01-01

Proposed further developments on Alaska's Arctic Coastal Plain raise questions about cumulative effects on arctic tundra ecosystems of development of multiple large oil fields. Maps of historical changes to the Prudhoe Bay Oil Field show indirect impacts can lag behind planned developments by many years and the total area eventually disturbed can greatly exceed the planned area of construction. For example, in the wettest parts of the oil field (flat thaw-lake plains), flooding and thermokarst covered more than twice the area directly affected by roads and other construction activities. Protecting critical wildlife habitat is the central issue for cumulative impact analysis in northern Alaska. Comprehensive landscape planning with the use of geographic information system technology and detailed geobotanical maps can help identify and protect areas of high wildlife use.

Evaluating pixel and object based image classification techniques for mapping plant invasions from UAV derived aerial imagery: Harrisia pomanensis as a case study

NASA Astrophysics Data System (ADS)

Mafanya, Madodomzi; Tsele, Philemon; Botai, Joel; Manyama, Phetole; Swart, Barend; Monate, Thabang

2017-07-01

Invasive alien plants (IAPs) not only pose a serious threat to biodiversity and water resources but also have impacts on human and animal wellbeing. To support decision making in IAPs monitoring, semi-automated image classifiers which are capable of extracting valuable information in remotely sensed data are vital. This study evaluated the mapping accuracies of supervised and unsupervised image classifiers for mapping Harrisia pomanensis (a cactus plant commonly known as the Midnight Lady) using two interlinked evaluation strategies i.e. point and area based accuracy assessment. Results of the point-based accuracy assessment show that with reference to 219 ground control points, the supervised image classifiers (i.e. Maxver and Bhattacharya) mapped H. pomanensis better than the unsupervised image classifiers (i.e. K-mediuns, Euclidian Length and Isoseg). In this regard, user and producer accuracies were 82.4% and 84% respectively for the Maxver classifier. The user and producer accuracies for the Bhattacharya classifier were 90% and 95.7%, respectively. Though the Maxver produced a higher overall accuracy and Kappa estimate than the Bhattacharya classifier, the Maxver Kappa estimate of 0.8305 is not significantly (statistically) greater than the Bhattacharya Kappa estimate of 0.8088 at a 95% confidence interval. The area based accuracy assessment results show that the Bhattacharya classifier estimated the spatial extent of H. pomanensis with an average mapping accuracy of 86.1% whereas the Maxver classifier only gave an average mapping accuracy of 65.2%. Based on these results, the Bhattacharya classifier is therefore recommended for mapping H. pomanensis. These findings will aid in the algorithm choice making for the development of a semi-automated image classification system for mapping IAPs.

Mapping Invasive Plant Species with a Combination of Field and Remote Sensing Data

NASA Astrophysics Data System (ADS)

Skowronek, S.; Feilhauer, H.; Van De Kerchove, R.; Ewald, M.; Aerts, R.; Somers, B.; Warrie, J.; Kempeneers, P.; Lenoir, J.; Honnay, O.; Asner, G. P.; Schmidtlein, S.; Hattab, T.; Rocchini, D.

2015-12-01

Advanced hyperspectral and LIDAR data offer a great potential to map and monitor invasive plant species and their impact on ecosystems. These species are often difficult to detect over large areas with traditional mapping approaches. One challenge is the combination of the remote sensing data with the field data for calibration and validation. Therefore, our goals were to (1) develop an approach that allows to efficiently map species invasions based on presence-only data of the target species and remote sensing data; and (2) use this approach to create distribution maps for invasive plant species in two study areas in western Europe, which offer the basis for further analysis of the impact of invasions and to infer possible management options. For this purpose, on the island of Sylt in Northern Germany, we collected vegetation data on 120 plots with a size of 3 m x 3 m with different cover fractions of two invasive plant species; the moss Campylopus introflexus and the shrub Rosa rugosa. In the forest of Compiègne in Northern France, we sampled a total of 50 plots with a size of 25 x 25 m, targeting the invasive tree Prunus serotina. In both study areas, independent validation datasets containing presence and absence points of the target species were collected. Airborne hyperspectral data (APEX), which were simultaneously acquired for both study areas in summer 2014, provided 285 spectral bands covering the visible, near infrared and short-wave infrared region with a pixel size of 1.8 and 3 m. First results showed that mapping using one-class classifiers is possible: For C. introflexus, AUC value was 0.89 and OAC 0.72, for R. rugosa., AUC was 0.93 and OAC 0.92. However, for both species, a few areas were mapped incorrectly. Possible explanations are the different appearances of the target species in different biotope types underrepresented in the calibration data, and a high cover of species with similar reflectance properties.

Geologic Map of the San Luis Quadrangle, Costilla County, Colorado

USGS Publications Warehouse

Machette, Michael N.; Thompson, Ren A.; Drenth, Benjamin J.

2008-01-01

The map area includes San Luis and the primarily rural surrounding area. San Luis, the county seat of Costilla County, is the oldest surviving settlement in Colorado (1851). West of the town are San Pedro and San Luis mesas (basalt-covered tablelands), which are horsts with the San Luis fault zone to the east and the southern Sangre de Cristo fault zone to the west. The map also includes the Sanchez graben (part of the larger Culebra graben), a deep structural basin that lies between the San Luis fault zone (on the west) and the central Sangre de Cristo fault zone (on the east). The oldest rocks exposed in the map area are the Pliocene to upper Oligocene basin-fill sediments of the Santa Fe Group, and Pliocene Servilleta Basalt, a regional series of 3.7?4.8 Ma old flood basalts. Landslide deposits and colluvium that rest on sediments of the Santa Fe Group cover the steep margins of the mesas. Rare exposures of the sediment are comprised of siltstones, sandstones, and minor fluvial conglomerates. Most of the low ground surrounding the mesas and in the graben is covered by surficial deposits of Quaternary age. The alluvial deposits are subdivided into three Pleistocene-age units and three Holocene-age units. The oldest Pleistocene gravel (unit Qao) forms extensive coalesced alluvial fan and piedmont surfaces, the largest of which is known as the Costilla Plain. This surface extends west from San Pedro Mesa to the Rio Grande. The primary geologic hazards in the map area are from earthquakes, landslides, and localized flooding. There are three major fault zones in the area (as discussed above), and they all show evidence for late Pleistocene to possible Holocene movement. The landslides may have seismogenic origins; that is, they may be stimulated by strong ground shaking during large earthquakes. Machette and Thompson based this geologic map entirely on new mapping, whereas Drenth supplied geophysical data and interpretations.

Forgotten forests--issues and prospects in biome mapping using Seasonally Dry Tropical Forests as a case study.

PubMed

Särkinen, Tiina; Iganci, João R V; Linares-Palomino, Reynaldo; Simon, Marcelo F; Prado, Darién E

2011-11-24

South America is one of the most species diverse continents in the world. Within South America diversity is not distributed evenly at both local and continental scales and this has led to the recognition of various areas with unique species assemblages. Several schemes currently exist which divide the continental-level diversity into large species assemblages referred to as biomes. Here we review five currently available biome maps for South America, including the WWF Ecoregions, the Americas basemap, the Land Cover Map of South America, Morrone's Biogeographic regions of Latin America, and the Ecological Systems Map. The comparison is performed through a case study on the Seasonally Dry Tropical Forest (SDTF) biome using herbarium data of habitat specialist species. Current biome maps of South America perform poorly in depicting SDTF distribution. The poor performance of the maps can be attributed to two main factors: (1) poor spatial resolution, and (2) poor biome delimitation. Poor spatial resolution strongly limits the use of some of the maps in GIS applications, especially for areas with heterogeneous landscape such as the Andes. Whilst the Land Cover Map did not suffer from poor spatial resolution, it showed poor delimitation of biomes. The results highlight that delimiting structurally heterogeneous vegetation is difficult based on remote sensed data alone. A new refined working map of South American SDTF biome is proposed, derived using the Biome Distribution Modelling (BDM) approach where georeferenced herbarium data is used in conjunction with bioclimatic data. Georeferenced specimen data play potentially an important role in biome mapping. Our study shows that herbarium data could be used as a way of ground-truthing biome maps in silico. The results also illustrate that herbarium data can be used to model vegetation maps through predictive modelling. The BDM approach is a promising new method in biome mapping, and could be particularly useful for mapping poorly known, fragmented, or degraded vegetation. We wish to highlight that biome delimitation is not an exact science, and that transparency is needed on how biomes are used as study units in macroevolutionary and ecological research.

Forgotten forests - issues and prospects in biome mapping using Seasonally Dry Tropical Forests as a case study

PubMed Central

2011-01-01

Background South America is one of the most species diverse continents in the world. Within South America diversity is not distributed evenly at both local and continental scales and this has led to the recognition of various areas with unique species assemblages. Several schemes currently exist which divide the continental-level diversity into large species assemblages referred to as biomes. Here we review five currently available biome maps for South America, including the WWF Ecoregions, the Americas basemap, the Land Cover Map of South America, Morrone's Biogeographic regions of Latin America, and the Ecological Systems Map. The comparison is performed through a case study on the Seasonally Dry Tropical Forest (SDTF) biome using herbarium data of habitat specialist species. Results Current biome maps of South America perform poorly in depicting SDTF distribution. The poor performance of the maps can be attributed to two main factors: (1) poor spatial resolution, and (2) poor biome delimitation. Poor spatial resolution strongly limits the use of some of the maps in GIS applications, especially for areas with heterogeneous landscape such as the Andes. Whilst the Land Cover Map did not suffer from poor spatial resolution, it showed poor delimitation of biomes. The results highlight that delimiting structurally heterogeneous vegetation is difficult based on remote sensed data alone. A new refined working map of South American SDTF biome is proposed, derived using the Biome Distribution Modelling (BDM) approach where georeferenced herbarium data is used in conjunction with bioclimatic data. Conclusions Georeferenced specimen data play potentially an important role in biome mapping. Our study shows that herbarium data could be used as a way of ground-truthing biome maps in silico. The results also illustrate that herbarium data can be used to model vegetation maps through predictive modelling. The BDM approach is a promising new method in biome mapping, and could be particularly useful for mapping poorly known, fragmented, or degraded vegetation. We wish to highlight that biome delimitation is not an exact science, and that transparency is needed on how biomes are used as study units in macroevolutionary and ecological research. PMID:22115315

Spatial prediction of ground subsidence susceptibility using an artificial neural network.

PubMed

Lee, Saro; Park, Inhye; Choi, Jong-Kuk

2012-02-01

Ground subsidence in abandoned underground coal mine areas can result in loss of life and property. We analyzed ground subsidence susceptibility (GSS) around abandoned coal mines in Jeong-am, Gangwon-do, South Korea, using artificial neural network (ANN) and geographic information system approaches. Spatial data of subsidence area, topography, and geology, as well as various ground-engineering data, were collected and used to create a raster database of relevant factors for a GSS map. Eight major factors causing ground subsidence were extracted from the existing ground subsidence area: slope, depth of coal mine, distance from pit, groundwater depth, rock-mass rating, distance from fault, geology, and land use. Areas of ground subsidence were randomly divided into a training set to analyze GSS using the ANN and a test set to validate the predicted GSS map. Weights of each factor's relative importance were determined by the back-propagation training algorithms and applied to the input factor. The GSS was then calculated using the weights, and GSS maps were created. The process was repeated ten times to check the stability of analysis model using a different training data set. The map was validated using area-under-the-curve analysis with the ground subsidence areas that had not been used to train the model. The validation showed prediction accuracies between 94.84 and 95.98%, representing overall satisfactory agreement. Among the input factors, "distance from fault" had the highest average weight (i.e., 1.5477), indicating that this factor was most important. The generated maps can be used to estimate hazards to people, property, and existing infrastructure, such as the transportation network, and as part of land-use and infrastructure planning.

Map showing outcrop of the coal-bearing units and land use in the Gulf Coast region

USGS Publications Warehouse

Warwick, Peter D.; SanFilipo, John R.; Crowley, Sharon S.; Thomas, Roger E.; Freid, John; Tully, John K.

1997-01-01

This map is a preliminary compilation of the outcrop geology of the known coal-bearing units in the Gulf Coast Coal region. The map has been compiled for use in the National Coal Resource Assessment Project currently being conducted by the U.S. Geological Survey, and will be updated as the assessment progresses. The purpose of the map is to show the distribution of coal-bearing rocks in the Gulf Coastal Plain Region and to show stratigraphic correlations, transportation network, fossil-fuel burning power plants, and federally managed lands in the region. It is hoped that this map may aid coal exploration and development in the region. Geologic contacts were digitized from paper copies of the maps listed in the reference section below. The primary source of information was the 1:500,000-scale state geology map series, but larger scale maps were use to better define certain areas, notably the Jackson-Claiborne contact in western Kentucky and Tennessee for example (Olive, 1980). Contacts along state boundaries were modified to best-fit information available from the border areas. Note that coal distribution in the mapped units is not uniform. For example, the Jackson Group contains coal in Texas, but in Mississippi is not presently known to contain significant coal deposits. The unit is widespread and in part non-marine and thus of potential future interest. In contrast, the Jackson Group is not shown in Georgia where it is mostly marine and residuum (weathered material) at the surface. Tertiary age coal has also been noted in the Vicksburg Group (Oligocene) of Louisiana and Mississippi, but is not shown on this map. Contacts with mapped surficial units are not always shown. The locations of coal mine permit boundaries are based on information available at the time of publication and were obtained from the Division of Surface Mining and Reclamation, Railroad Commission of Texas, Austin, and the Injection and Mining Division, Department of Natural Resources, Baton Rouge, Louisiana. The correlation of map units and formation names generally follow Galloway and others (1991). We have placed the Paleocene-Eocene boundary in the middle of the Calvert Bluff Formation in Texas based on unpublished pollen biostratigraphy reports (N.O. Fredericksen, unpublished data, 1993; D.J. Nichols, unpublished data, 1996).

Geologic Map of Lassen Volcanic National Park and Vicinity, California

USGS Publications Warehouse

Clynne, Michael A.; Muffler, L.J. Patrick

2010-01-01

The geologic map of Lassen Volcanic National Park (LVNP) and vicinity encompasses 1,905 km2 at the south end of the Cascade Range in Shasta, Lassen, Tehama, and Plumas Counties, northeastern California (fig. 1, sheet 3). The park includes 430 km2 of scenic volcanic features, glacially sculpted terrain, and the most spectacular array of thermal features in the Cascade Range. Interest in preserving the scenic wonders of the Lassen area as a national park arose in the early 1900s to protect it from commercial development and led to the establishment in 1907 of two small national monuments centered on Lassen Peak and Cinder Cone. The eruptions of Lassen Peak in 1914-15 were the first in the Cascade Range since widespread settling of the West in the late 1800s. Through the printed media, the eruptions aroused considerable public interest and inspired renewed efforts, which had languished since 1907, to establish a national park. In 1916, Lassen Volcanic National Park was established by combining the areas of the previously established national monuments and adjacent lands. The southernmost Cascade Range is bounded on the west by the Sacramento Valley and the Klamath Mountains, on the south by the Sierra Nevada, and on the east by the Basin and Range geologic provinces. Most of the map area is underlain by middle to late Pleistocene volcanic rocks; Holocene, early Pleistocene, and late Pliocene volcanic rocks (<3.5 m.y.) are less common. Paleozoic and Mesozoic rocks are inferred to underlie the volcanic deposits (Jachens and Saltus, 1983), but the nearest exposures of pre-Tertiary rocks are 15 km to the south, 9 km to the southwest, and 12 km to the west. Diller (1895) recognized the young volcanic geology and produced the first geologic map of the Lassen area. The map (sheet 1) builds on and extends geologic mapping by Williams (1932), Macdonald (1963, 1964, 1965), and Wilson (1961). The Lassen Peak area mapped by Christiansen and others (2002) and published in greater detail (1:24,000) was modified for inclusion here. Figure 2 (sheet 3) shows the mapping credit for previous work; figure 3 (sheet 3) shows locations discussed throughout the text. A CD-ROM entitled Database for the Geologic Map of Lassen Volcanic National Park and Vicinity, California accompanies the printed map (Muffler and others, 2010). The CD-ROM contains ESRI compatible geographic information system data files used to create the 1:50,000-scale geologic map, both geologic and topographic data and their associated metadata files, and printable versions of the geologic map and pamphlet as PDF formatted files. The 1:50,000-scale geologic map was compiled from 1:24,000-scale geologic maps of individual quadrangles that are also included in the CD-ROM. It also contains ancillary data that support the map including locations of rock samples selected for chemical analysis (Clynne and others, 2008) and radiometric dating, photographs of geologic features, and links to related data or web sites. Data contained in the CD-ROM are also available on this Web site. The southernmost Cascade Range consists of a regional platform of basalt and basaltic andesite, with subordinate andesite and sparse dacite. Nested within these regional rocks are 'volcanic centers', defined as large, long-lived, composite, calc-alkaline edifices erupting the full range of compositions from basalt to rhyolite, but dominated by andesite and dacite. Volcanic centers are produced by the focusing of basaltic flux from the mantle and resultant enhanced interaction of mafic magma with the crust. Collectively, volcanic centers mark the axis of the southernmost Cascade Range. The map area includes the entire Lassen Volcanic Center, parts of three older volcanic centers (Maidu, Dittmar, and Latour), and the products of regional volcanism (fig. 4, sheet 3). Terminology used for subdivision of the Lassen Volcanic Center has been modified from Clynne (1984, 1990).

Combination of techniques for mapping structural and functional connectivity of soil erosion processes: a case study in a small watershed

NASA Astrophysics Data System (ADS)

Seeger, Manuel; Taguas, Encarnación; Brings, Christine; Wirtz, Stefan; Rodrigo Comino, Jesus; Albert, Enrique; Ries, Johabbes B.

2016-04-01

Sediment connectivity is understood as the interaction of sediment sources, the sinks and the pathways which connect them. During the last decade, the research on connectivity has increased, as it is crucial to understand the relation between the observed sediments at a certain point, and the processes leading them to that location. Thus, the knowledge of the biogeophysical features involved in sediment connectivity in an area of interest is essential to understand its functioning and to design treatments allowing its management, e. g. to reduce soil erosion. The structural connectivity is given by landscape elements which enable the production, transport and deposition of sediments, whereas the functional connectivity is understood here as variable processes that lead the sediments through a catchment. Therefore, 2 different levels of connectivity have been considered which superpose each other according to the catchments conditions. We studied the different connectivity features in a catchment almost completely covered by an olive grove. It is located south of Córdoba (Spain), close to the city of Puente Genil. The olive plantation type is of low productivity. The soil management was no tillage for the least 9 years. The farmer allow weed growing in the lanes although he applied herbicide treatment and tractor passes usually in the end of spring. Firstly, a detailed mapping of geomorphodynamic features was carried out. We identified spatially distributed areas of increased sheet-wash and crusting, but also areas where rill erosion has leadedto a high density of rills and small gullies. Especially within these areas rock outcrops up to several m² were mapped, showing like this (former) intense erosion processes. In addition, field measurements with different methodologies were applied on infiltration (single ring infiltrometers, rainfall simulations), soil permeability (Guelph permeameter), interrill erosion (rainfall simulator) and concentrated flow (rill experiment). The measurements were conducted at representative areas identified in advance by precedent mapping. Preliminary results show that the rills are highly effective in producing sediments, but also in connecting fast the different sources with the catchment's outlet. But also they act as a disconnecting feature to the areas of observation, as they may lead the runoff (and the transported sediments) outside the catchment. On the other side, the experiments showed that the evidently degraded areas produce only very delayed runoff, and thus also sediments, whereas the areas with stable deep soils show evidences of fast runoff and erosive responses. The preliminary results of the combination of mapping and experimental techniques demonstrate the different levels at where functional and structural connectivity have to be evaluated. The latter one may be, as a geomorphological feature, the result of former process distributions, whereas the directly observable (functional) connectivity may shift in time due to internal feedbacks, such as the result of soil degradation.

12 CFR 345.43 - Content and availability of public file.

Code of Federal Regulations, 2011 CFR

2011-01-01

...; (3) A list of the bank's branches, their street addresses, and geographies; (4) A list of branches... street addresses, and geographies; (5) A list of services (including hours of operation, available loan...) A map of each assessment area showing the boundaries of the area and identifying the geographies...

Exploring discrepancies between quantitative validation results and the geomorphic plausibility of statistical landslide susceptibility maps

NASA Astrophysics Data System (ADS)

Steger, Stefan; Brenning, Alexander; Bell, Rainer; Petschko, Helene; Glade, Thomas

2016-06-01

Empirical models are frequently applied to produce landslide susceptibility maps for large areas. Subsequent quantitative validation results are routinely used as the primary criteria to infer the validity and applicability of the final maps or to select one of several models. This study hypothesizes that such direct deductions can be misleading. The main objective was to explore discrepancies between the predictive performance of a landslide susceptibility model and the geomorphic plausibility of subsequent landslide susceptibility maps while a particular emphasis was placed on the influence of incomplete landslide inventories on modelling and validation results. The study was conducted within the Flysch Zone of Lower Austria (1,354 km2) which is known to be highly susceptible to landslides of the slide-type movement. Sixteen susceptibility models were generated by applying two statistical classifiers (logistic regression and generalized additive model) and two machine learning techniques (random forest and support vector machine) separately for two landslide inventories of differing completeness and two predictor sets. The results were validated quantitatively by estimating the area under the receiver operating characteristic curve (AUROC) with single holdout and spatial cross-validation technique. The heuristic evaluation of the geomorphic plausibility of the final results was supported by findings of an exploratory data analysis, an estimation of odds ratios and an evaluation of the spatial structure of the final maps. The results showed that maps generated by different inventories, classifiers and predictors appeared differently while holdout validation revealed similar high predictive performances. Spatial cross-validation proved useful to expose spatially varying inconsistencies of the modelling results while additionally providing evidence for slightly overfitted machine learning-based models. However, the highest predictive performances were obtained for maps that explicitly expressed geomorphically implausible relationships indicating that the predictive performance of a model might be misleading in the case a predictor systematically relates to a spatially consistent bias of the inventory. Furthermore, we observed that random forest-based maps displayed spatial artifacts. The most plausible susceptibility map of the study area showed smooth prediction surfaces while the underlying model revealed a high predictive capability and was generated with an accurate landslide inventory and predictors that did not directly describe a bias. However, none of the presented models was found to be completely unbiased. This study showed that high predictive performances cannot be equated with a high plausibility and applicability of subsequent landslide susceptibility maps. We suggest that greater emphasis should be placed on identifying confounding factors and biases in landslide inventories. A joint discussion between modelers and decision makers of the spatial pattern of the final susceptibility maps in the field might increase their acceptance and applicability.

Analysis of Environmental Vulnerability in The Landslide Areas (Case Study: Semarang Regency)

NASA Astrophysics Data System (ADS)

Hani'ah; Firdaus, H. S.; Nugraha, A. L.

2017-12-01

The Land conversion can increase the risk of landslide disaster in Semarang Regency caused by human activity. Remote sensing and geographic information system to be used in this study to mapping the landslide areas because satellite image data can represent the object on the earth surface in wide area coverage. Satellite image Landsat 8 is used to mapping land cover that processed by supervised classification method. The parameters to mapping landslide areas are based on land cover, rainfall, slope, geological factors and soil types. Semarang Regency have the minimum value of landslide is 1.6 and the maximum value is 4.3, which is dominated by landslide prone areas about 791.27 km2. The calculation of the environmental vulnerability index in the study area is based on Perka BNPB No. 2/2012. Accumulation score of environmental vulnerability index is moderate value, that means environment condition must be considered, such as vegetation as ground cover and many others aspects. The range of NDVI value shows that density level in conservation areas (0.030 - 0.844) and conservation forest (0.045 - 0.849), which rarely until high density level. The results of this study furthermore can be assessed to reduce disaster risks from landslide as an effort of disaster preventive.

An anatomical and functional topography of human auditory cortical areas

PubMed Central

Moerel, Michelle; De Martino, Federico; Formisano, Elia

2014-01-01

While advances in magnetic resonance imaging (MRI) throughout the last decades have enabled the detailed anatomical and functional inspection of the human brain non-invasively, to date there is no consensus regarding the precise subdivision and topography of the areas forming the human auditory cortex. Here, we propose a topography of the human auditory areas based on insights on the anatomical and functional properties of human auditory areas as revealed by studies of cyto- and myelo-architecture and fMRI investigations at ultra-high magnetic field (7 Tesla). Importantly, we illustrate that—whereas a group-based approach to analyze functional (tonotopic) maps is appropriate to highlight the main tonotopic axis—the examination of tonotopic maps at single subject level is required to detail the topography of primary and non-primary areas that may be more variable across subjects. Furthermore, we show that considering multiple maps indicative of anatomical (i.e., myelination) as well as of functional properties (e.g., broadness of frequency tuning) is helpful in identifying auditory cortical areas in individual human brains. We propose and discuss a topography of areas that is consistent with old and recent anatomical post-mortem characterizations of the human auditory cortex and that may serve as a working model for neuroscience studies of auditory functions. PMID:25120426

Tile prediction schemes for wide area motion imagery maps in GIS

NASA Astrophysics Data System (ADS)

Michael, Chris J.; Lin, Bruce Y.

2017-11-01

Wide-area surveillance, traffic monitoring, and emergency management are just several of many applications benefiting from the incorporation of Wide-Area Motion Imagery (WAMI) maps into geographic information systems. Though the use of motion imagery as a GIS base map via the Web Map Service (WMS) standard is not a new concept, effectively streaming imagery is particularly challenging due to its large scale and the multidimensionally interactive nature of clients that use WMS. Ineffective streaming from a server to one or more clients can unnecessarily overwhelm network bandwidth and cause frustratingly large amounts of latency in visualization to the user. Seamlessly streaming WAMI through GIS requires good prediction to accurately guess the tiles of the video that will be traversed in the near future. In this study, we present an experimental framework for such prediction schemes by presenting a stochastic interaction model that represents a human user's interaction with a GIS video map. We then propose several algorithms by which the tiles of the stream may be predicted. Results collected both within the experimental framework and using human analyst trajectories show that, though each algorithm thrives under certain constraints, the novel Markovian algorithm yields the best results overall. Furthermore, we make the argument that the proposed experimental framework is sufficient for the study of these prediction schemes.

Computing visible areas from proposed recreation developments...a case study

Treesearch

Gary H. Elsner

1971-01-01

A new computerized technique called VIEWIT for measuring the terrain visible from a given point was applied in a study on the Black Hills National Forest, South Dakota. The seen area from 12 heavily visited scenic points and along three proposed routes for a scenic tramway were delineated. The computer produced overlay maps that show the maximum area visible from each...

Where on Mars Does Carbon Dioxide Frost Form Often?

NASA Image and Video Library

2016-07-08

This map shows the frequency of carbon dioxide frost's presence at sunrise on Mars, as a percentage of days year-round. Carbon dioxide ice more often covers the ground at night in some mid-latitude regions than in polar regions, where it is generally absent for much of summer and fall. Color coding is based on data from the Mars Climate Sounder instrument on NASA's Mars Reconnaissance Orbiter. A color-key bar below the map shows how colors correspond to frequencies. Yellow indicates high frequencies, identifying areas where carbon dioxide ice is present on the ground at night during most of the year. Blue identifies areas where it is rarely present; red is intermediate. Areas without color coding are regions where carbon dioxide frost is not detected at any time of year. The areas with highest frequency of overnight carbon dioxide frost correspond to regions with surfaces of loose dust, which do not retain heat well, compared to rockier areas. Those areas also have some of the highest mid-afternoon temperatures on the planet. The dust surface heats up and cools off rapidly. http://photojournal.jpl.nasa.gov/catalog/PIA20758

GDP Spatialization and Economic Differences in South China Based on NPP-VIIRS Nighttime Light Imagery

NASA Astrophysics Data System (ADS)

Zhao, M.

2017-12-01

Accurate data on gross domestic product (GDP) at pixel level are needed to understand the dynamics of regional economies. GDP spatialization is the basis of quantitative analysis on economic diversities of different administrative divisions and areas with different natural or humanistic attributes. Data from the Visible Infrared Imaging Radiometer Suite (VIIRS), carried by the Suomi National Polar-orbiting Partnership (NPP) satellite, are capable of estimating GDP, but few studies have been conducted for mapping GDP at pixel level and further pattern analysis of economic differences in different regions using the VIIRS data. This paper produced a pixel-level (500 m × 500 m) GDP map for South China in 2014 and quantitatively analyzed economic differences among diverse geomorphological types. Based on a regression analysis, the total nighttime light (TNL) of corrected VIIRS data were found to exhibit R2 values of 0.8935 and 0.9243 for prefecture GDP and county GDP, respectively. This demonstrated that TNL showed a more significant capability in reflecting economic status (R2 > 0.88) than other nighttime light indices (R2 < 0.52), and showed quadratic polynomial relationships with GDP rather than simple linear correlations at both prefecture and county levels. The corrected NPP-VIIRS data showed a better fit than the original data, and the estimation at the county level was better than at the prefecture level. The pixel-level GDP map indicated that: (a) economic development in coastal areas was higher than that in inland areas; (b) low altitude plains were the most developed areas, followed by low altitude platforms and low altitude hills; and (c) economic development in middle altitude areas, and low altitude hills and mountains remained to be strengthened.

Identification, definition and mapping of terrestrial ecosystems in interior Alaska

NASA Technical Reports Server (NTRS)

Anderson, J. H. (Principal Investigator)

1973-01-01

The author has identified the following significant results. Two new, as yet unfinished vegetation maps are presented. These tend further to substantiate the belief that ERTS-1 imagery is a valuable mapping tool. Newly selected scenes show that vegetation interpretations can be refined through use of non-growing season imagery, particularly through the different spectral characteristics of vegetation lacking foliage and through the effect of vegetation structure on apparent snow cover. Scenes now are available for all test area north of the Alaska Range except Mt. McKinley National Park. No support was obtained for the hypothesis that similar interband ratios, from two areas apparently different spectrally because of different sun angles, would indicate similar surface features. However, attempts to test this hypothesis have so far been casual.

Transmission dynamics of schistosomiasis in Zimbabwe: A mathematical and GIS Approach

NASA Astrophysics Data System (ADS)

Ngarakana-Gwasira, E. T.; Bhunu, C. P.; Masocha, M.; Mashonjowa, E.

2016-06-01

Temperature and presence of water bodies are known to influence the transmission dynamics of schistosomiasis. In this work, effects of water bodies (taken in context of rainfall patterns) and temperature from 1950 to 2000 are considered in the model. With the aid of Geographic Information System (GIS), the reproduction number is mapped on the Zimbabwean country. Results of the mapping show high reproduction numbers along the Lowveld and the Zambezi valley catchment area. High reproduction numbers suggest high levels of schistosomiasis. This result suggests more control efforts should be targeted in these areas with high reproduction numbers.

Uav Photogrammetry: a Practical Solution for Challenging Mapping Projects

NASA Astrophysics Data System (ADS)

Saadatseresht, M.; Hashempour, A. H.; Hasanlou, M.

2015-12-01

We have observed huge attentions to application of unmanned aerial vehicle (UAV) in aerial mapping since a decade ago. Though, it has several advantages for handling time/cost/quality issues, there are a dozen of challenges in working with UAVs. In this paper, we; as the Robotic Photogrammetry Research Group (RPRG), will firstly review these challenges then show its advantages in three special practical projects. For each project, we will share our experiences through description of the UAV specifications, flight settings and processing steps. At the end, we will illustrate final result of each project and show how this technology could make unbelievable benefits to clients including 3D city realistic model in decimetre level, ultra high quality map production in several centimetre level, and accessing to a high risk and rough relief area for mapping aims.

Decadal and Seasonal Variations of Alpine Lakes in Glacierized areas of Central Asia during 1990-2015

NASA Astrophysics Data System (ADS)

Li, J.; Warner, T.; Chen, X.; Bao, A.

2016-12-01

Central Asia is one of the world's most vulnerable areas responding to global change. Glacier lakes in the alpine regions remain sensitive to climatic change and fluctuate with temperature and precipitation variations. Study shows that glaciers in Central Asia have retreated dramatically, leading to the expansion of the existing glacial lakes and the emergence of many new glacier lakes. The existence of these lakes increases the possibility of outburst flood during the ice melting season, which can bring a disaster to the downstream area. Mapping glacial lakes and monitoring their changes would improve our understanding of regional climate change and glacier-related hazards. Glacial lakes in Central Asia are mainly located at the Tianshan Mountains, the Altai Mountains, the Kunlun Mountains and the Pamirs with average elevation more than 1500 meters. Most of these lakes are supplied with the glaciers or snowmelt water during the summer seasons. Satellite remote sensing provides an efficient and objective tool to analyze the status and variations of glacial lakes. The increased availability of remote sensing sensors with appropriate spatial and temporal resolutions, broad coverage makes lake investigations more feasible and cost-effective. The paper intends to map glacier lake changes in glacierized alpine mountains with Landsat TM/ETM+ imagery. More than 600 scenes of Landsat images in circa 1990, circa 2000, circa 2010 and circa 2015 are used to map the decadal glacial lake changes over the Central Asia, and about 8 expanding glacial lakes are selected to map seasonal changes. Over 12000 glacial lakes were mapped in circa 1990, and in 2015, lake number are more than 16000, most of these new lakes are emerging in the last 10 years. The result shows that the number and area of the glacial lakes in the Altain Mountain remain stable, while the Tianshan Mountain have experienced expanding changes in the last two decades, and about a half number of lake areas are increased by 10% since the circa 1990. The glacier data, air temperature and precipitation data are also used explorer the relations between glacial lake changes and regional climate change. The result showed that glacier recession brings newly emerging glacial lakes, and precipitation increases are the main factors of lake expanding.

Geologic Map and Engineering Properties of the Surficial Deposits of the Tok Area, East-Central Alaska

USGS Publications Warehouse

Carrara, Paul E.

2007-01-01

The Tok area 1:100,000-scale map, through which the Alaska Highway runs, is in east-central Alaska about 160 km west of the Yukon border. The surficial geologic mapping in the map area is in support of the 'Geologic Mapping in support of land, resources, and hazards issues in Alaska' Project of the USGS National Cooperative Geologic Mapping Program. The Tok map area contains parts of three physiographic provinces, the Alaska Range, the Yukon-Tanana Upland, and the Northway-Tanana Lowland. The high, rugged, glaciated landscape of the eastern Alaska Range dominates the southwestern map area. The highest peak, an unnamed summit at the head of Cathedral Rapids Creek No. 2, rises to 2166 m. The gently rolling hills of the Yukon-Tanana Upland, in the northern map area, rise to about 1000 m. The Northway-Tanana Lowland contains the valley of the westerly flowing Tanana River. Elevations along the floor of the lowland generally range between 470 and 520 m. The dominant feature within the map is the Tok fan, which occupies about 20 percent of the map area. This large (450 km2), nearly featureless fan contains a high percentage of volcanic clasts derived from outside the present-day drainage of the Tok River. Because the map area is dominated by various surficial deposits, the map depicts 26 different surficial units consisting of man-made, alluvial, colluvial, eolian, lacustrine, organic, glaciofluvial, glacial, and periglacial deposits. The accompanying table provides information concerning the various units including their properties, characteristics, resource potential, and associated hazards in this area of the upper Tanana valley.

The use of multibeam backscatter intensity data as a tool for mapping glacial deposits in the Central North Sea, UK

NASA Astrophysics Data System (ADS)

Stewart, Heather; Bradwell, Tom

2014-05-01

Multibeam backscatter intensity data acquired offshore eastern Scotland and north-eastern England have been used to map drumlin fields, large arcuate moraine ridges, smaller scale moraine ridges, and incised channels on the sea floor. The study area includes the catchments of the previously proposed, but only partly mapped, Strathmore, Forth-Tay, and Tweed palaeo-ice streams. The ice sheet glacial landsystem is extremely well preserved on the sea bed and comprehensive mapping of the seafloor geomorphology has been undertaken. The authors demonstrate the value in utilising not only digital terrain models (both NEXTMap and multibeam bathymetry derived) in undertaking geomorphological mapping, but also examining the backscatter intensity data that is often overlooked. Backscatter intensity maps were generated using FM Geocoder by the British Geological Survey. FM Geocoder corrects the backscatter intensities registered by the multibeam echosounder system, and then geometrically corrects and positions each acoustic sample in a backscatter mosaic. The backscatter intensity data were gridded at the best resolution per dataset (between 2 and 5 m). The strength of the backscattering is dependent upon sediment type, grain size, survey conditions, sea-bed roughness, compaction and slope. A combination of manual interpretation and semi-automated classification of the backscatter intensity data (a predictive method for mapping variations in surficial sea-bed sediments) has been undertaken in the study area. The combination of the two methodologies has produced a robust glacial geomorphological map for the study area. Four separate drumlin fields have been mapped in the study area indicative of fast-flowing and persistent ice-sheet flow configurations. A number of individual drumlins are also identified located outside the fields. The drumlins show as areas of high backscatter intensity compared to the surrounding sea bed, indicating the drumlins comprise mixed sediments of gravelly sands and sandy gravels compared to the surrounding sandy and muddy sediments. Moraines are indicated as areas of high backscatter intensity and comprise coarse grained sediments. A range of moraine sizes have been identified from large scale moraines reflecting both frontal still stands or re-advances of the ice-sheet margin, de geer moraines and smaller moraines that may represent annual variations. Meltwater channels and tunnel valleys are revealed as areas of low backscatter intensity reflecting post-glacial soft sediment infill of the depressions incised into coarser grained and higher strength glacial deposits by these features.

Space Radar Image of Manaus, Brazil

NASA Image and Video Library

1999-01-27

These two images were created using data from the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR). On the left is a false-color image of Manaus, Brazil acquired April 12, 1994, onboard space shuttle Endeavour. In the center of this image is the Solimoes River just west of Manaus before it combines with the Rio Negro to form the Amazon River. The scene is around 8 by 8 kilometers (5 by 5 miles) with north toward the top. The radar image was produced in L-band where red areas correspond to high backscatter at HH polarization, while green areas exhibit high backscatter at HV polarization. Blue areas show low backscatter at VV polarization. The image on the right is a classification map showing the extent of flooding beneath the forest canopy. The classification map was developed by SIR-C/X-SAR science team members at the University of California,Santa Barbara. The map uses the L-HH, L-HV, and L-VV images to classify the radar image into six categories: Red flooded forest Green unflooded tropical rain forest Blue open water, Amazon river Yellow unflooded fields, some floating grasses Gray flooded shrubs Black floating and flooded grasses Data like these help scientists evaluate flood damage on a global scale. Floods are highly episodic and much of the area inundated is often tree-covered. http://photojournal.jpl.nasa.gov/catalog/PIA01712

The use of the LANDSAT data collection system and imagery in reservoir management and operation. [Maine, Vermont, New Hamphire, Canada, St. John River, Beech Ridge, Merrimack River, and Franklin Falls

NASA Technical Reports Server (NTRS)

Cooper, S. (Principal Investigator); Buckelew, T. D.; Mckim, H. L.; Merry, C. J.

1977-01-01

The author has identified the following significant results. An increase in the data collection system's (DCS) ability to function in the flood control mission with no additional manpower was demonstrated during the storms which struck New England during April and May of 1975 and August 1976. It was found that for this watershed, creditable flood hydrographs could be generated from DCS data. It was concluded that an ideal DCS for reservoir regulation would draw features from LANDSAT and GOES. MSS grayscale computer printout and a USGS topographic map were compared, yielding an optimum computer classification map of the wetland areas of the Merrimack River estuary. A classification accuracy of 75% was obtained for the wetlands unit, taking into account the misclassified and the unclassified pixels. The MSS band 7 grayscale printouts of the Franklin Falls reservoir showed good agreement to USGS topographic maps in total area of water depicted at the low water reservoir stage and at the maximum inundation level. Preliminary analysis of the LANDSAT digital data using the GISS computer algorithms showed that the radiance of snow cover/vegetation varied from approximately 20 mW/sq cm sr in nonvegetated areas to less than 4 mW/sq cm sr for densely covered forested area.

Subsurface structure identification uses derivative analyses of the magnetic data in Candi Umbul-Telomoyo geothermal prospect area

NASA Astrophysics Data System (ADS)

Septyasari, U.; Niasari, S. W.; Maghfira, P. D.

2018-04-01

Telomoyo geothermal prospect area is located in Central Java, Indonesia. One of the manifestations around Telomoyo is a warm spring, called Candi Umbul. The hydrothermal fluids from the manifestation could be from the subsurface flowing up through geological structures. The previous research about 2D magnetic modeling in Candi Umbul showed that there was a normal fault with strike/dip N60°E/45° respectively. This research aims to know the distance boundary and the kind of the geological structure in the study area. We also compared the geological structure direction based on the geologic map and the derivative maps. We used derivative analyses of the magnetic data, i.e. First Horizontal Derivative (FHD) which is the rate of change of the horizontal gradient in the horizontal direction. FHD indicates the boundaries of the geological structure. We also used Second Vertical Derivative (SVD) which is the rate of change of the vertical gradient in the vertical direction. SVD can reveal normal fault or thrust fault. The FHD and SVD maps show that the geological structure boundary has the same direction with the north west-south east geological structure. The geological structure boundary is in 486 m of the local distance. Our result confirms that there is a normal fault in the study area.

A GIS-based DRASTIC model for assessing intrinsic groundwater vulnerability in northeastern Missan governorate, southern Iraq

NASA Astrophysics Data System (ADS)

Al-Abadi, Alaa M.; Al-Shamma'a, Ayser M.; Aljabbari, Mukdad H.

2017-03-01

In this study, intrinsic groundwater vulnerability for the shallow aquifer in northeastern Missan governorate, south of Iraq is evaluated using commonly used DRASTIC model in framework of GIS environment. Preparation of DRASTIC parameters is attained through gathering data from different sources including field survey, geological and meteorological data, a digital elevation model DEM of the study area, archival database, and published research. The different data used to build DRASTIC model are arranged in a geospatial database using spatial analyst extension of ArcGIS 10.2 software. The obtained results related to the vulnerability to general contaminants show that the study area is characterized by two vulnerability zones: low and moderate. Ninety-four percentage (94 %) of the study area has a low class of groundwater vulnerability to contamination, whereas a total of (6 %) of the study area has moderate vulnerability. The pesticides DRASTIC index map shows that the study area is also characterized by two zones of vulnerability: low and moderate. The DRASTIC map of this version clearly shows that small percentage (13 %) of the study area has low vulnerability to contamination, and most parts have moderate vulnerability (about 87 %). The final results indicate that the aquifer system in the interested area is relatively protected from contamination on the groundwater surface. To mitigate the contamination risks in the moderate vulnerability zones, a protective measure must be put before exploiting the aquifer and before comprehensive agricultural activities begin in the area.

California State Waters Map Series-Offshore of Point Reyes, California

USGS Publications Warehouse

Watt, Janet T.; Dartnell, Peter; Golden, Nadine E.; Greene, H. Gary; Erdey, Mercedes D.; Cochrane, Guy R.; Johnson, Samuel Y.; Hartwell, Stephen R.; Kvitek, Rikk G.; Manson, Michael W.; Endris, Charles A.; Dieter, Bryan E.; Sliter, Ray W.; Krigsman, Lisa M.; Lowe, Erik; Chinn, John L.; Watt, Janet T.; Cochran, Susan A.

2015-01-01

This publication about the Offshore of Point Reyes map area includes ten map sheets that contain explanatory text, in addition to this descriptive pamphlet and a data catalog of geographic information system (GIS) files. Sheets 1, 2, and 3 combine data from four different sonar surveys to generate comprehensive high-resolution bathymetry and acoustic-backscatter coverage of the map area. These data reveal a range of physiographic features (highlighted in the perspective views on sheet 4) such as the flat, sediment-covered seafloor in Drakes Bay, as well as abundant “scour depressions” on the Bodega Head–Tomales Point shelf (see sheet 9) and local, tectonically controlled bedrock uplifts. To validate geological and biological interpretations of the sonar data shown in sheets 1, 2, and 3, the U.S. Geological Survey towed a camera sled over specific offshore locations, collecting both video and photographic imagery; these “ground-truth” surveying data are summarized on sheet 6. Sheet 5 is a “seafloor character” map, which classifies the seafloor on the basis of depth, slope, rugosity (ruggedness), and backscatter intensity and which is further informed by the ground-truth-survey imagery. Sheet 7 is a map of “potential habitats,” which are delineated on the basis of substrate type, geomorphology, seafloor process, or other attributes that may provide a habitat for a specific species or assemblage of organisms. Sheet 8 compiles representative seismic-reflection profiles from the map area, providing information on the subsurface stratigraphy and structure of the map area. Sheet 9 shows the distribution and thickness of young sediment (deposited over the last about 21,000 years, during the most recent sea-level rise) in both the map area and the larger Salt Point to Drakes Bay region, interpreted on the basis of the seismic-reflection data, and it identifies the Offshore of Point Reyes map area as lying within the Bodega Head–Tomales Point shelf, Point Reyes bar, and Bolinas shelf domains. Sheet 10 is a geologic map that merges onshore geologic mapping (compiled from existing maps by the California Geological Survey) and new offshore geologic mapping that is based on integration of high-resolution bathymetry and backscatter imagery (sheets 1, 2, 3), seafloor-sediment and rock samples (Reid and others, 2006), digital camera and video imagery (sheet 6), and high-resolution seismic-reflection profiles (sheet 8), as well as aerial-photographic interpretation of nearshore areas. The information provided by the map sheets, pamphlet, and data catalog have a broad range of applications. High-resolution bathymetry, acoustic backscatter, ground-truth-surveying imagery, and habitat mapping all contribute to habitat characterization and ecosystem-based management by providing essential data for delineation of marine protected areas and ecosystem restoration. Many of the maps provide high-resolution baselines that will be critical for monitoring environmental change associated with climate change, coastal development, or other forcings. High-resolution bathymetry is a critical component for modeling coastal flooding caused by storms and tsunamis, as well as inundation associated with longer term sea-level rise. Seismic-reflection and bathymetric data help characterize earthquake and tsunami sources, critical for natural-hazard assessments of coastal zones. Information on sediment distribution and thickness is essential to the understanding of local and regional sediment transport, as well as the development of regional sediment-management plans. In addition, siting of any new offshore infrastructure (for example, pipelines, cables, or renewable-energy facilities) will depend on high-resolution mapping. Finally, this mapping will both stimulate and enable new scientific research and also raise public awareness of, and education about, coastal environments and issues.

Active and Passive Remote Sensing Data Time Series for Flood Detection and Surface Water Mapping

NASA Astrophysics Data System (ADS)

Bioresita, Filsa; Puissant, Anne; Stumpf, André; Malet, Jean-Philippe

2017-04-01

As a consequence of environmental changes surface waters are undergoing changes in time and space. A better knowledge of the spatial and temporal distribution of surface waters resources becomes essential to support sustainable policies and development activities. Especially because surface waters, are not only a vital sweet water resource, but can also pose hazards to human settlements and infrastructures through flooding. Floods are a highly frequent disaster in the world and can caused huge material losses. Detecting and mapping their spatial distribution is fundamental to ascertain damages and for relief efforts. Spaceborne Synthetic Aperture Radar (SAR) is an effective way to monitor surface waters bodies over large areas since it provides excellent temporal coverage and, all-weather day-and-night imaging capabilities. However, emergent vegetation, trees, wind or flow turbulence can increase radar back-scatter returns and pose problems for the delineation of inundated areas. In such areas, passive remote sensing data can be used to identify vegetated areas and support the interpretation of SAR data. The availability of new Earth Observation products, for example Sentinel-1 (active) and Sentinel-2 (passive) imageries, with both high spatial and temporal resolution, have the potential to facilitate flood detection and monitoring of surface waters changes which are very dynamic in space and time. In this context, the research consists of two parts. In the first part, the objective is to propose generic and reproducible methodologies for the analysis of Sentinel-1 time series data for floods detection and surface waters mapping. The processing chain comprises a series of pre-processing steps and the statistical modeling of the pixel value distribution to produce probabilistic maps for the presence of surface waters. Images pre-processing for all Sentinel-1 images comprise the reduction SAR effect like orbit errors, speckle noise, and geometric effects. A modified Split Based Approach (MSBA) is used in order to focus on surface water areas automatically and facilitate the estimation of class models for water and non-water areas. A Finite Mixture Model is employed as the underlying statistical model to produce probabilistic maps. Subsequently, bilateral filtering is applied to take into account spatial neighborhood relationships in the generation of final map. The elimination of shadows effect is performed in a post-processing step. The processing chain is tested on three case studies. The first case is a flood event in central Ireland, the second case is located in Yorkshire county / Great Britain, and the third test case covers a recent flood event in northern Italy. The tests showed that the modified SBA step and the Finite Mixture Models can be applied for the automatic surface water detection in a variety of test cases. An evaluation again Copernicus products derived from very-high resolution imagery was performed, and showed a high overall accuracy and F-measure of the obtained maps. This evaluation also showed that the use of probability maps and bilateral filtering improved the accuracy of classification results significantly. Based on this quantitative evaluation, it is concluded that the processing chain can be applied for flood mapping from Sentinel-1 data. To estimate robust statistical distributions the method requires sufficient surface waters areas in the observed zone and sufficient contrast between surface waters and other land use classes. Ongoing research addresses the fusion of Sentinel-1 and passive remote sensing data (e.g. Sentinel-2) in order to reduce the current shortcomings in the developed processing chain. In this work, fusion is performed at the feature level to better account for the difference image properties of SAR and optical sensors. Further, the processing chain is currently being optimized in terms of calculation time for a further integration as a flood mapping service on the A2S (Alsace Aval Sentinel) high-performance computing infrastructure of University of Strasbourg.

Alteration Map Showing Major Faults and Veins and Associated Water-Quality Signatures of the Animas River Watershed Headwaters Near Silverton, Southwest Colorado

USGS Publications Warehouse

Bove, Dana J.; Yager, Douglas B.; Mast, M. Alisa; Dalton, J. Brad

2007-01-01

This map was produced to provide hard-copy and digital data for alteration assemblages in the historical mining area centered on the Tertiary San Juan and Silverton calderas. The data have direct application to geoenvironmental and mineral exploration objectives. This dataset represents alteration mapping for the upper Animas River watershed near Silverton, Colorado. The map is based on detailed 1:12,000-scale field mapping, X-ray diffraction (XRD) analysis, mineral mapping by remote sensing (AVIRIS) data, and 1:24,000-scale aerial photographic interpretation. Geologic structures were compiled and generalized from multiple published and unpublished sources (Burbank and Luedke, 1964; Steven and others, 1974; Luedke and Burbank 1975a, b; Lipman, 1976; Luedke and Burbank, 1987; Luedke, 1996) (see Index Map). Unpublished mapping of the Ironton quadrangle by D.J. Bove and J.P. Kurtz in 1997-1999 was included.

Quaternary Geology and Liquefaction Susceptibility, Napa, California 1:100,000 Quadrangle: A Digital Database

USGS Publications Warehouse

Sowers, Janet M.; Noller, Jay S.; Lettis, William R.

1998-01-01

Earthquake-induced ground failures such as liquefaction have historically brought loss of life and damage to property and infrastructure. Observations of the effects of historical large-magnitude earthquakes show that the distribution of liquefaction phenomena is not random. Liquefaction is restricted to areas underlain by loose, cohesionless sands and silts that are saturated with water. These areas can be delineated on the basis of thorough geologic, geomorphic, and hydrologic mapping and map analysis (Tinsley and Holzer, 1990; Youd and Perkins, 1987). Once potential liquefaction zones are delineated, appropriate public and private agencies can prepare for and mitigate seismic hazard in these zones. In this study, we create a liquefaction susceptibility map of the Napa 1:100,000 quadrangle using Quaternary geologic mapping, analysis of historical liquefaction information, groundwater data, and data from other studies. The study is atterned after state-of-the-art studies by Youd (1973) Dupre and Tinsley (1980) and Dupre (1990) in the Monterey-Santa Cruz area, Tinsley and others (1985) in the Los Angeles area, and Youd and Perkins (1987) in San Mateo County, California. The study area comprises the northern San Francisco Metropolitan Area, including the cities of Santa Rosa, Vallejo, Napa, Novato, Martinez, and Fairfield (Figure 1). Holocene estuarine deposits, Holocene stream deposits, eolian sands, and artificial fill are widely present in the region (Helley and Lajoie, 1979) and are the geologic materials of greatest concern. Six major faults capable of producing large earthquakes cross the study area, including the San Andreas, Rodgers Creek, Hayward, West Napa, Concord, and Green Valley faults (Figure 1).

Predicting the Location of Human Perirhinal Cortex, Brodmann's area 35, from MRI

PubMed Central

Augustinack, Jean C.; Huber, Kristen E.; Stevens, Allison A.; Roy, Michelle; Frosch, Matthew P.; van der Kouwe, André J.W.; Wald, Lawrence L.; Van Leemput, Koen; McKee, Ann; Fischl, Bruce

2012-01-01

The perirhinal cortex (Brodmann's area 35) is a multimodal area that is important for normal memory function. Specifically, perirhinal cortex is involved in detection of novel objects and manifests neurofibrillary tangles in Alzheimer's disease very early in disease progression. We scanned ex vivo brain hemispheres at standard resolution (1 mm × 1 mm × 1 mm) to construct pial/white matter surfaces in FreeSurfer and scanned again at high resolution (120 μm × 120 μm × 120 μm) to determine cortical architectural boundaries. After labeling perirhinal area 35 in the high resolution images, we mapped the high resolution labels to the surface models to localize area 35 in fourteen cases. We validated the area boundaries determined using histological Nissl staining. To test the accuracy of the probabilistic mapping, we measured the Hausdorff distance between the predicted and true labels and found that the median Hausdorff distance was 4.0 mm for left hemispheres (n = 7) and 3.2 mm for right hemispheres (n = 7) across subjects. To show the utility of perirhinal localization, we mapped our labels to a subset of the Alzheimer's Disease Neuroimaging Initiative dataset and found decreased cortical thickness measures in mild cognitive impairment and Alzheimer's disease compared to controls in the predicted perirhinal area 35. Our ex vivo probabilistic mapping of perirhinal cortex provides histologically validated, automated and accurate labeling of architectonic regions in the medial temporal lobe, and facilitates the analysis of atrophic changes in a large dataset for earlier detection and diagnosis. PMID:22960087

Participatory Mapping for Flood Disaster Zoning based on World View-2 Data in Long Beluah, North Kalimantan Province

NASA Astrophysics Data System (ADS)

Sudaryatno; Awanda, Disyacitta; Eka Pratiwi, Sufiyana

2017-12-01

Flood is one of the most frequent disasters in Indonesia. These conditions cause the necessary efforts to reduce the impact of these hazards. To reduce the impact of these hazards is to understand spatially the impact of previous disasters. Participatory mapping is one of the solutions to be able to assist in reducing the impact of flood disaster by conducting flood zoning so it can be known the range of the flood. The community plays an important role in participatory mapping because the experiences and mental maps of the community are the main sources of information used. North Kalimantan Province has a very large watershed area that is in Kayan watershed, there are several villages, one of them is Long Beluah Village. Kayan watershed has a flood problem annually that affects most of the areas including the Long Beluah Village. This study aims to map the zoning of floods in the village of Long Beluah in a participatory manner using remote sensing World View-2 data within community, so that people also understand the conditions they face. The method for achieving that goal is participatory mapping which means community involvement as well as the ability of community mental maps that will make an important contribution in this research. The results of this study show that flood zoning can be mapped based on experience and community mental maps that the greatest floods in February 2015 inundated most of the community settlements in Long Beluah Village. There are few places from the uninhabited areas of settlements and serve as refugee camps. The participatory zonation map of the participatory floods is quite appropriate with the situation at the time of the greatest flood that hit the village of Long Beluah, so that through the map can be drawn up plans to reduce the impact of such disasters such as evacuation routes and a more strategic refuge point.

Flood-hazard mapping in Honduras in response to Hurricane Mitch

USGS Publications Warehouse

Mastin, M.C.

2002-01-01

The devastation in Honduras due to flooding from Hurricane Mitch in 1998 prompted the U.S. Agency for International Development, through the U.S. Geological Survey, to develop a country-wide systematic approach of flood-hazard mapping and a demonstration of the method at selected sites as part of a reconstruction effort. The design discharge chosen for flood-hazard mapping was the flood with an average return interval of 50 years, and this selection was based on discussions with the U.S. Agency for International Development and the Honduran Public Works and Transportation Ministry. A regression equation for estimating the 50-year flood discharge using drainage area and annual precipitation as the explanatory variables was developed, based on data from 34 long-term gaging sites. This equation, which has a standard error of prediction of 71.3 percent, was used in a geographic information system to estimate the 50-year flood discharge at any location for any river in the country. The flood-hazard mapping method was demonstrated at 15 selected municipalities. High-resolution digital-elevation models of the floodplain were obtained using an airborne laser-terrain mapping system. Field verification of the digital elevation models showed that the digital-elevation models had mean absolute errors ranging from -0.57 to 0.14 meter in the vertical dimension. From these models, water-surface elevation cross sections were obtained and used in a numerical, one-dimensional, steady-flow stepbackwater model to estimate water-surface profiles corresponding to the 50-year flood discharge. From these water-surface profiles, maps of area and depth of inundation were created at the 13 of the 15 selected municipalities. At La Lima only, the area and depth of inundation of the channel capacity in the city was mapped. At Santa Rose de Aguan, no numerical model was created. The 50-year flood and the maps of area and depth of inundation are based on the estimated 50-year storm tide.

Geologic map of southwestern Sequoia National Park, Tulare County, California

USGS Publications Warehouse

Sisson, Thomas W.; Moore, James G.

2013-01-01

This map shows the geology of 675 km2 (260 mi2) on the west slope of the Sierra Nevada, California, mainly in Sequoia National Park and Sequoia National Forest. It was produced by the U.S. Geological Survey (USGS) at the request of the National Park Service to complete the geologic map coverage of Kings Canyon and Sequoia National Parks. The area includes the Mineral King 15’ topographic quadrangle (sheet 1) and strips along the east and northeast edges of the Kaweah 15’ topographic quadrangle (sheet 2), both in Tulare County. Mapping was performed mainly on the 1:24,000-scale Mineral King, Silver City, Quinn Peak, Moses Mountain, Case Mountain, and Dennison Peak 7.5’ topographic quadrangle bases. Rocks within the study area are chiefly Cretaceous granites and granodiorites of the Sierra Nevada batholith that intruded coherent masses of Mesozoic metasedimentary and metavolcanic rocks. Quaternary till and talus are the principal surficial deposits, with the exception of a large bouldery alluvial apron near the southwest corner of the map area. The study area includes the headwaters of the Kaweah River (East and South Forks), Tule River (North Fork and North Fork of the Middle Fork), and the Little Kern River. Relief is considerable, with elevations spanning from 1,500 feet along the Middle Fork Kaweah River to 12,432 feet at the summit of Florence Peak along the crest of the Great Western Divide.

Preliminary Geologic Map of the Sanchez Reservoir Quadrangle and Eastern Part of the Garcia Quadrangle, Costilla County, Colorado

USGS Publications Warehouse

Thompson, Ren A.; Machette, Michael N.; Drenth, Benjamin J.

2007-01-01

This geologic map is based entirely on new mapping by Thompson and Machette, whereas the geophysical data and interpretations were supplied by Drenth. The map area includes most of San Pedro Mesa, a basalt covered mesa that is uplifted as a horst between the Southern Sangre de Cristo fault zone (on the west) and the San Luis fault zone on the east. The map also includes most of the Sanchez graben, a deep structural basin that lies between the San Luis fault zone (on the west) and the Central Sangre de Cristo fault zone on the east. The oldest rocks in the map area are Proterozoic granites and Paleozoic sedimentary rocks, which are only exposed in a small hill on the west-central part of the mesa. The low hills that rise above San Pedro mesa are comprised of middle(?) Miocene volcanic rocks that are undated, but possibly correlative with mapped rocks to the east of Sanchez Reservoir. The bulk of the map area is comprised of the Servilleta Basalt, a regional series of flood basalts of Pliocene age. The west, north, and northeast margins of the mesa are covered by extensive landslide deposits that rest on poorly exposed sediment of the Santa Fe Group. Rare exposures of the sediment are comprised of siltstones, sandstones, and minor fluvial conglomerates. Most of the low ground surrounding the mesa is covered by surficial deposits of Quaternary age. The piedmont alluvium is subdivided into three Pleistocene units, and three Holocene units. The oldest Pleistocene gravel (unit Qao) forms an extensive coalesced alluvial fan and piedmont surface that is known as the Costilla Plains. This surface extends west from San Pedro Mesa to the Rio Grande. The primary geologic hazards in the map are are from earthquakes and landslides. There are three major fault zones in the area (as discussed above), and they all show evidence for late Pleistocene to possible Holocene movement. Two generations of landslides are mapped (younger and older), and both may have seismogenic origins.

Assessing MODIS-based Products and Techniques for Detecting Gypsy Moth Defoliation

NASA Technical Reports Server (NTRS)

Spruce, Joseph P.; Hargrove, William; Smoot, James C.; Prados, Don; McKellip, Rodney; Sader, Steven A.; Gasser, Jerry; May, George

2008-01-01

The project showed potential of MODIS and VIIRS time series data for contributing defoliation detection products to the USFS forest threat early warning system. This study yielded the first satellite-based wall-to-wall 2001 gypsy moth defoliation map for the study area. Initial results led to follow-on work to map 2007 gypsy moth defoliation over the eastern United States (in progress). MODIS-based defoliation maps offer promise for aiding aerial sketch maps either in planning surveys and/or adjusting acreage estimates of annual defoliation. More work still needs to be done to assess potential of technology for "now casts"of defoliation.

Preliminary Geologic Map of the Big Pine Mountain Quadrangle, California

USGS Publications Warehouse

Vedder, J.G.; McLean, Hugh; Stanley, R.G.

1995-01-01

Reconnaissance geologic mapping of the San Rafael Primitive Area (now the San Rafael Wilderness) by Gower and others (1966) and Vedder an others (1967) showed s number of stratigraphic and structural ambiguities. To help resolve some of those problems, additional field work was done on parts of the Big Pine Moutain quadrangle during short intervals in 1981 and 1984, and 1990-1994.

Mapping irrigated areas in Afghanistan over the past decade using MODIS NDVI

USGS Publications Warehouse

Pervez, Md Shahriar; Budde, Michael; Rowland, James

2014-01-01

Agricultural production capacity contributes to food security in Afghanistan and is largely dependent on irrigated farming, mostly utilizing surface water fed by snowmelt. Because of the high contribution of irrigated crops (> 80%) to total agricultural production, knowing the spatial distribution and year-to-year variability in irrigated areas is imperative to monitoring food security for the country. We used 16-day composites of the Normalized Difference Vegetation Index (NDVI) from the Moderate Resolution Imaging Spectroradiometer (MODIS) sensor to create 23-point time series for each year from 2000 through 2013. Seasonal peak values and time series were used in a threshold-dependent decision tree algorithm to map irrigated areas in Afghanistan for the last 14 years. In the absence of ground reference irrigated area information, we evaluated these maps with the irrigated areas classified from multiple snapshots of the landscape during the growing season from Landsat 5 optical and thermal sensor images. We were able to identify irrigated areas using Landsat imagery by selecting as irrigated those areas with Landsat-derived NDVI greater than 0.30–0.45, depending on the date of the Landsat image and surface temperature less than or equal to 310 Kelvin (36.9 ° C). Due to the availability of Landsat images, we were able to compare with the MODIS-derived maps for four years: 2000, 2009, 2010, and 2011. The irrigated areas derived from Landsat agreed well r2 = 0.91 with the irrigated areas derived from MODIS, providing confidence in the MODIS NDVI threshold approach. The maps portrayed a highly dynamic irrigated agriculture practice in Afghanistan, where the amount of irrigated area was largely determined by the availability of surface water, especially snowmelt, and varied by as much as 30% between water surplus and water deficit years. During the past 14 years, 2001, 2004, and 2008 showed the lowest levels of irrigated area (~ 1.5 million hectares), attesting to the severe drought conditions in those years, whereas 2009, 2012 and 2013 registered the largest irrigated area (~ 2.5 million hectares) due to record snowpack and snowmelt in the region. The model holds promise the ability to provide near-real-time (by the end of the growing seasons) estimates of irrigated area, which are beneficial for food security monitoring as well as subsequent decision making for the country. While the model is developed for Afghanistan, it can be adopted with appropriate adjustments in the derived threshold values to map irrigated areas elsewhere.

Preliminary geologic map of the Bowen Mountain quadrangle, Grand and Jackson Counties, Colorado

USGS Publications Warehouse

Cole, James C.; Braddock, William A.; Brandt, Theodore R.

2011-01-01

The map shows the geology of an alpine region in the southern Never Summer Mountains, including parts of the Never Summer Wilderness Area, the Bowen Gulch Protection Area, and the Arapaho National Forest. The area includes Proterozoic crystalline rocks in fault contact with folded and overturned Paleozoic and Mesozoic sedimentary rocks and Upper Cretaceous(?) and Paleocene Middle Park Formation. The folding and faulting appears to reflect a singular contractional deformation (post-Middle Park, so probably younger than early Eocene) that produced en echelon structural uplift of the Proterozoic basement of the Front Range. The geologic map indicates there is no through-going \\"Never Summer thrust\\" fault in this area. The middle Tertiary structural complex was intruded in late Oligocene time by basalt, quartz latite, and rhyolite porphyry plugs that also produced minor volcanic deposits; these igneous rocks are collectively referred to informally as the Braddock Peak intrusive-volcanic complex whose type area is located in the Mount Richthofen quadrangle immediately north (Cole and others, 2008; Cole and Braddock, 2009). Miocene boulder gravel deposits are preserved along high-altitude ridges that probably represent former gravel channels that developed during uplift and erosion in middle Tertiary time.

Cognitive Mapping Based on Conjunctive Representations of Space and Movement

PubMed Central

Zeng, Taiping; Si, Bailu

2017-01-01

It is a challenge to build robust simultaneous localization and mapping (SLAM) system in dynamical large-scale environments. Inspired by recent findings in the entorhinal–hippocampal neuronal circuits, we propose a cognitive mapping model that includes continuous attractor networks of head-direction cells and conjunctive grid cells to integrate velocity information by conjunctive encodings of space and movement. Visual inputs from the local view cells in the model provide feedback cues to correct drifting errors of the attractors caused by the noisy velocity inputs. We demonstrate the mapping performance of the proposed cognitive mapping model on an open-source dataset of 66 km car journey in a 3 km × 1.6 km urban area. Experimental results show that the proposed model is robust in building a coherent semi-metric topological map of the entire urban area using a monocular camera, even though the image inputs contain various changes caused by different light conditions and terrains. The results in this study could inspire both neuroscience and robotic research to better understand the neural computational mechanisms of spatial cognition and to build robust robotic navigation systems in large-scale environments. PMID:29213234

Surface magnetic field mapping on high albedo marking areas of the moon

NASA Astrophysics Data System (ADS)

Shibuya, H.; Aikawa, K.; Tsunakawa, H.; Takahashi, F.; Shimizu, H.; Matsushima, M.

2009-12-01

The correlation between high albedo markings (HAM) on the surface of the moon and strong magnetic anomalies has been claimed since the early time of the lunar magnetic field study (Hood and Schubert, 1980). Hood et al. (1989) mapped the smoothed magnetic field over the Reiner Gamma region using Lunar Prospector magnetometer (LP-MAG) data, and showed that the position of them matches well. We have developed a method to recover the 3-d magnetic field from satellite field observations (EPR method which stands for Equivalent Pole Reduction; Toyoshima et al. 2008). Applying EPR to the several areas of strong magnetic anomalies, we calculated the magnetic anomaly maps of near surface regions, to see how the anomaly and the HAM correlate each other. The data used is of the Lunar Prospector magnetometer (LP-MAG). They are selected from low altitude observations performed in 1998 to 1999. The areas studied are Reiner Gamma, Airy, Descartes, Abel, and Crisium Antipode regions. The EPR determines a set of magnetic monopoles at the moon surface which produce the magnetic field of the observation. In each studied area, we put poles in 0.1° intervals of both latitude and longitude, then the magnetic field at 5km in altitude is calculated. The field distribution is superimposed with the albedo map made from Clementine data. The total force (Bf) maps indicate that the HMA occurs at the strong anomaly regions, but their shape does not quite overlie. However, taking horizontal component (Bh), not only position but the shape and size of the anomalies coincide with HMA regions. It is particularly true for the Reiner Gamma, and Descartes regions. The shape of HMA fits in a Bh contour. The HMA is argued to be formed by the reduction of solar wind particles which are shielded by the magnetic field. Since the deflection of the charged particle becomes large at large horizontal component, the Bh distribution showed here support the argument.

The Geographic Information System applied to study schistosomiasis in Pernambuco

PubMed Central

Barbosa, Verônica Santos; Loyo, Rodrigo Moraes; Guimarães, Ricardo José de Paula Souza e; Barbosa, Constança Simões

2017-01-01

ABSTRACT OBJECTIVE Diagnose risk environments for schistosomiasis in coastal localities of Pernambuco using geoprocessing techniques. METHODS A coproscopic and malacological survey were carried out in the Forte Orange and Serrambi areas. Environmental variables (temperature, salinity, pH, total dissolved solids and water fecal coliform dosage) were collected from Biomphalaria breeding sites or foci. The spatial analysis was performed using ArcGis 10.1 software, applying the kernel estimator, elevation map, and distance map. RESULTS In Forte Orange, 4.3% of the population had S. mansoni and were found two B. glabrata and 26 B. straminea breeding sites. The breeding sites had temperatures of 25ºC to 41ºC, pH of 6.9 to 11.1, total dissolved solids between 148 and 661, and salinity of 1,000 d. In Serrambi, 4.4% of the population had S. mansoni and were found seven B. straminea and seven B. glabrata breeding sites. Breeding sites had temperatures of 24ºC to 36ºC, pH of 7.1 to 9.8, total dissolved solids between 116 and 855, and salinity of 1,000 d. The kernel estimator shows the clusters of positive patients and foci of Biomphalaria, and the digital elevation map indicates areas of rainwater concentration. The distance map shows the proximity of the snail foci with schools and health facilities. CONCLUSIONS Geoprocessing techniques prove to be a competent tool for locating and scaling the risk areas for schistosomiasis, and can subsidize the health services control actions. PMID:29166439

Village Level Tsunami Threat Maps for Tamil Nadu, SE Coast of India: Numerical Modeling Technique

NASA Astrophysics Data System (ADS)

MP, J.; Kulangara Madham Subrahmanian, D.; V, R. M.

2014-12-01

The Indian Ocean tsunami (IOT) devastated several countries of North Indian Ocean. India is one of the worst affected countries after Indonesia and Sri Lanka. In India, Tamil Nadu suffered maximum with fatalities exceeding 8,000 people. Historical records show that tsunami has invaded the shores of Tamil Nadu in the past and has made people realize that the tsunami threat looms over Tamil Nadu and it is necessary to evolve strategies for tsunami threat management. The IOT has brought to light that tsunami inundation and runup varied within short distances and for the disaster management for tsunami, large scale maps showing areas that are likely to be affected by future tsunami are identified. Therefore threat assessment for six villages including Mamallapuram (also called Mahabalipuram) which is famous for its rock-cut temples, from the northern part of Tamil Nadu state of India has been carried out and threat maps categorizing the coast into areas of different degree of threat are prepared. The threat was assessed by numerical modeling using TUNAMI N2 code considering different tsunamigenic sources along the Andaman - Sumatra trench. While GEBCO and C-Map data was used for bathymetry and for land elevation data was generated by RTK - GPS survey for a distance of 1 km from shore and SRTM for the inland areas. The model results show that in addition to the Sumatra source which generated the IOT in 2004, earthquakes originating in Car Nicobar and North Andaman can inflict more damage. The North Andaman source can generate a massive tsunami and an earthquake of magnitude more than Mw 9 can not only affect Tamil Nadu but also entire south east coast of India. The runup water level is used to demarcate the tsunami threat zones in the villages using GIS.

Preliminary report on geophysics of the Verde River headwaters region, Arizona

USGS Publications Warehouse

Langenheim, V.E.; Duval, J.S.; Wirt, Laurie; DeWitt, Ed

2000-01-01

This report summarizes the acquisition, data processing, and preliminary interpretation of a high-resolution aeromagnetic and radiometric survey near the confluence of the Big and Little Chino basins in the headwaters of the Verde River, Arizona. The goal of the aeromagnetic study is to improve understanding of the geologic framework as it affects groundwater flow, particularly in relation to the occurrence of springs in the upper Verde River headwaters region. Radiometric data were also collected to map surficial rocks and soils, thus aiding geologic mapping of the basin fill. Additional gravity data were collected to enhance existing coverage. Both aeromagnetic and gravity data indicate a large gradient along the Big Chino fault, a fault with Quaternary movement. Filtered aeromagnetic data show other possible faults within the basin fill and areas where volcanic rocks are shallowly buried. Gravity lows associated with Big Chino and Williamson Valleys indicate potentially significant accumulations of low-density basin fill. The absence of a gravity low associated with Little Chino Valley indicates that high-density rocks are shallow. The radiometric maps show higher radioactivity associated with the Tertiary latites and with the sediments derived from them. The surficial materials on the eastern side of the Big Chino Valley are significantly lower in radioactivity and reflect the materials derived from the limestone and basalt east of the valley. The dividing line between the low radioactivity materials to the east and the higher radioactiviy materials to the west coincides approximately with the major drainage system of the valley, locally known as Big Chino Wash. This feature is remarkably straight and is approximately parallel to the Big Chino Fault. The uranium map shows large areas with concentrations greater than 5 ppm eU, and we expect that these areas will have a significantly higher risk potential for indoor radon.

Geophysical imaging of karst features in Missouri

NASA Astrophysics Data System (ADS)

Obi, Jeremiah Chukwunonso

Automated electrical resistivity tomography (ERT) supported with multichannel analysis of surface waves (MASW) and boring data were used to map karst related features in Missouri in order to understand karst processes better in Missouri. Previous works on karst in Missouri were mostly surficial mapping of bedrock outcrops and joints, which are not enough to define the internal structure of karst system, since most critical processes in karst occur underground. To understand these processes better, the density, placement and pattern of karst related features like solution-widened joints and voids, as well as top of bedrock were mapped. In the course of the study, six study sites were visited in Missouri. The sites were in Nixa, Gasconade River Bridge in Lebanon, Battlefield, Aurora, Protem and Richland. The case studies reflect to a large extent some of the problems inherent in karst terrain, ranging from environmental problems to structural problems especially sinkhole collapses. The result of the study showed that karst in Missouri is mostly formed as a result of piping of sediments through solution-widened joints, with a pattern showing that the joints/fractures are mostly filled with moist clay-sized materials of low resistivity values. The highest density of mapped solution-widened joints was one in every one hundred and fifty feet, and these areas are where intense dissolution is taking place, and bedrock pervasively fractured. The study also showed that interpreted solution-widened joints trend in different directions, and often times conform with known structural lineaments in the area. About 40% of sinkhole collapses in the study areas are anthropogenic. Karst in Missouri varies, and can be classified as a combination of kI (juvenile), kIII (mature) and kIV (complex) karsts.

Corticostriatal connectivity fingerprints: Probability maps based on resting-state functional connectivity.

PubMed

Jaspers, Ellen; Balsters, Joshua H; Kassraian Fard, Pegah; Mantini, Dante; Wenderoth, Nicole

2017-03-01

Over the last decade, structure-function relationships have begun to encompass networks of brain areas rather than individual structures. For example, corticostriatal circuits have been associated with sensorimotor, limbic, and cognitive information processing, and damage to these circuits has been shown to produce unique behavioral outcomes in Autism, Parkinson's Disease, Schizophrenia and healthy ageing. However, it remains an open question how abnormal or absent connectivity can be detected at the individual level. Here, we provide a method for clustering gross morphological structures into subregions with unique functional connectivity fingerprints, and generate network probability maps usable as a baseline to compare individual cases against. We used connectivity metrics derived from resting-state fMRI (N = 100), in conjunction with hierarchical clustering methods, to parcellate the striatum into functionally distinct clusters. We identified three highly reproducible striatal subregions, across both hemispheres and in an independent replication dataset (N = 100) (dice-similarity values 0.40-1.00). Each striatal seed region resulted in a highly reproducible distinct connectivity fingerprint: the putamen showed predominant connectivity with cortical and cerebellar sensorimotor and language processing areas; the ventromedial striatum cluster had a distinct limbic connectivity pattern; the caudate showed predominant connectivity with the thalamus, frontal and occipital areas, and the cerebellum. Our corticostriatal probability maps agree with existing connectivity data in humans and non-human primates, and showed a high degree of replication. We believe that these maps offer an efficient tool to further advance hypothesis driven research and provide important guidance when investigating deviant connectivity in neurological patient populations suffering from e.g., stroke or cerebral palsy. Hum Brain Mapp 38:1478-1491, 2017. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

The Analysis of Object-Based Change Detection in Mining Area: a Case Study with Pingshuo Coal Mine

NASA Astrophysics Data System (ADS)

Zhang, M.; Zhou, W.; Li, Y.

2017-09-01

Accurate information on mining land use and land cover change are crucial for monitoring and environmental change studies. In this paper, RapidEye Remote Sensing Image (Map 2012) and SPOT7 Remote Sensing Image (Map 2015) in Pingshuo Mining Area are selected to monitor changes combined with object-based classification and change vector analysis method, we also used R in highresolution remote sensing image for mining land classification, and found the feasibility and the flexibility of open source software. The results show that (1) the classification of reclaimed mining land has higher precision, the overall accuracy and kappa coefficient of the classification of the change region map were 86.67 % and 89.44 %. It's obvious that object-based classification and change vector analysis which has a great significance to improve the monitoring accuracy can be used to monitor mining land, especially reclaiming mining land; (2) the vegetation area changed from 46 % to 40 % accounted for the proportion of the total area from 2012 to 2015, and most of them were transformed into the arable land. The sum of arable land and vegetation area increased from 51 % to 70 %; meanwhile, build-up land has a certain degree of increase, part of the water area was transformed into arable land, but the extent of the two changes is not obvious. The result illustrated the transformation of reclaimed mining area, at the same time, there is still some land convert to mining land, and it shows the mine is still operating, mining land use and land cover are the dynamic procedure.

Map showing geochemical data for panned stream sediments from the Bread Loaf Further Planning Area, Addison and Washington counties, Vermont

USGS Publications Warehouse

Grosz, A.E.; Schruben, P.G.; Atelsek, P.J.

1987-01-01

A geochemical survey of bedrock samples in the Bread Loaf Roadless Area (index map; fig. 1) was conducted by the U.S. Geological Survey (USGS) during October, 1981 in order to outline areas that may contain undiscovered mineral deposits. This report describes the results of a geochemical analysis of panned concentrates collected from stream sediments, and complements other geologic and geochemical investigations of the area (Slack and Bitar, 1983). The present study has offered us a chance to identify sampling media and a technique most appropriate for the enhancement of certain metallic elements in samples of panned concentrate. This study is important to the resource evaluation of the Bread Loaf Roadless Area because it reveals that geochemical anomalies produced by this technique are not evident in the standard magnetic and nonmagnetic fractions of panned concentrates.

Multi-component intrinsic brain activities as a safe, alternative to cortical stimulation for sensori-motor mapping in neurosurgery.

PubMed

Neshige, Shuichiro; Matsuhashi, Masao; Kobayashi, Katsuya; Sakurai, Takeyo; Shimotake, Akihiro; Hitomi, Takefumi; Kikuchi, Takayuki; Yoshida, Kazumichi; Kunieda, Takeharu; Matsumoto, Riki; Takahashi, Ryosuke; Miyamoto, Susumu; Maruyama, Hirofumi; Matsumoto, Masayasu; Ikeda, Akio

2018-06-18

To assess the feasibility of multi-component electrocorticography (ECoG)-based mapping using "wide-spectrum, intrinsic-brain activities" for identifying the primary sensori-motor area (S1-M1) by comparing that using electrical cortical stimulation (ECS). We evaluated 14 epilepsy patients with 1514 subdural electrodes implantation covering the perirolandic cortices at Kyoto University Hospital between 2011 and 2016. We performed multi-component, ECoG-based mapping (band-pass filter, 0.016-300/600 Hz) involving combined analyses of the single components: movement-related cortical potential (<0.5-1 Hz), event-related synchronization (76-200 Hz), and event-related de-synchronization (8-24 Hz) to identify the S1-M1. The feasibility of multi-component mapping was assessed through comparisons with single-component mapping and ECS. Among 54 functional areas evaluation, ECoG-based maps showed significantly higher rate of localization concordances with ECS maps when the three single-component maps were consistent than when those were inconsistent with each other (p < 0.001 in motor, and p = 0.02 in sensory mappings). Multi-component mapping revealed high sensitivity (89-90%) and specificity (94-97%) as compared with ECS. Wide-spectrum, multi-component ECoG-based mapping is feasible, having high sensitivity/specificity relative to ECS. This safe (non-stimulus) mapping strategy, alternative to ECS, would allow clinicians to rule in/out the possibility of brain function prior to resection surgery. Copyright © 2018 International Federation of Clinical Neurophysiology. Published by Elsevier B.V. All rights reserved.

Mapping Air Population

NASA Astrophysics Data System (ADS)

Peterson, Michael P.; Hunt, Paul; Weiß, Konrad

2018-05-01

"Air population" refers to the total number of people flying above the earth at any point in time. The total number of passengers can then be estimated by multiplying the number of seats for each aircraft by the current seat occupancy rate. Using this method, the estimated air population is determined by state for the airspace over the United States. In the interactive, real-time mapping system, maps are provided to show total air population, the density of air population (air population / area of state), and the ratio of air population to ground population.

ERTS-B applications to Minnesota resource management

NASA Technical Reports Server (NTRS)

Sizer, J. E. (Principal Investigator)

1976-01-01

The author has identified the following significant results. The shape, pattern, and extent of surface water (e.g. lakes) can be readily mapped. Comparing detailed maps of several lakes in Itasca County with the areas classified as water by the LANDSAT data shows that some lakes have changed considerably since they were mapped. Due to several droughts this year (1976), the water level in most lakes has dropped. At this time, it seems feasible that LANDSAT digital tape data estimate lake water level change, due to the 1976 drought conditions.

Population weighted raster maps can communicate findings of social audits: examples from three continents.

PubMed

Mitchell, Steven; Cockcroft, Anne; Andersson, Neil

2011-12-21

Maps can portray trends, patterns, and spatial differences that might be overlooked in tabular data and are now widely used in health research. Little has been reported about the process of using maps to communicate epidemiological findings. Population weighted raster maps show colour changes over the study area. Similar to the rasters of barometric pressure in a weather map, data are the health occurrence--a peak on the map represents a higher value of the indicator in question. The population relevance of each sentinel site, as determined in the stratified last stage random sample, combines with geography (inverse-distance weighting) to provide a population-weighted extension of each colour. This transforms the map to show population space rather than simply geographic space. Maps allowed discussion of strategies to reduce violence against women in a context of political sensitivity about quoting summary indicator figures. Time-series maps showed planners how experiences of health services had deteriorated despite a reform programme; where in a country HIV risk behaviours were improving; and how knowledge of an economic development programme quickly fell off across a region. Change maps highlighted where indicators were improving and where they were deteriorating. Maps of potential impact of interventions, based on multivariate modelling, displayed how partial and full implementation of programmes could improve outcomes across a country. Scale depends on context. To support local planning, district maps or local government authority maps of health indicators were more useful than national maps; but multinational maps of outcomes were more useful for regional institutions. Mapping was useful to illustrate in which districts enrolment in religious schools--a rare occurrence--was more prevalent. Population weighted raster maps can present social audit findings in an accessible and compelling way, increasing the use of evidence by planners with limited numeracy skills or little time to look at evidence. Maps complement epidemiological analysis, but they are not a substitute. Much less do they substitute for rigorous epidemiological designs, like randomised controlled trials.

Bush Encroachment Mapping for Africa - Multi-Scale Analysis with Remote Sensing and GIS

NASA Astrophysics Data System (ADS)

Graw, V. A. M.; Oldenburg, C.; Dubovyk, O.

2015-12-01

Bush encroachment describes a global problem which is especially facing the savanna ecosystem in Africa. Livestock is directly affected by decreasing grasslands and inedible invasive species which defines the process of bush encroachment. For many small scale farmers in developing countries livestock represents a type of insurance in times of crop failure or drought. Among that bush encroachment is also a problem for crop production. Studies on the mapping of bush encroachment so far focus on small scales using high-resolution data and rarely provide information beyond the national level. Therefore a process chain was developed using a multi-scale approach to detect bush encroachment for whole Africa. The bush encroachment map is calibrated with ground truth data provided by experts in Southern, Eastern and Western Africa. By up-scaling location specific information on different levels of remote sensing imagery - 30m with Landsat images and 250m with MODIS data - a map is created showing potential and actual areas of bush encroachment on the African continent and thereby provides an innovative approach to map bush encroachment on the regional scale. A classification approach links location data based on GPS information from experts to the respective pixel in the remote sensing imagery. Supervised classification is used while actual bush encroachment information represents the training samples for the up-scaling. The classification technique is based on Random Forests and regression trees, a machine learning classification approach. Working on multiple scales and with the help of field data an innovative approach can be presented showing areas affected by bush encroachment on the African continent. This information can help to prevent further grassland decrease and identify those regions where land management strategies are of high importance to sustain livestock keeping and thereby also secure livelihoods in rural areas.

Detailed interpretation of aeromagnetic data from the Patagonia Mountains area, southeastern Arizona

USGS Publications Warehouse

Bultman, Mark W.

2015-01-01

Euler deconvolution depth estimates derived from aeromagnetic data with a structural index of 0 show that mapped faults on the northern margin of the Patagonia Mountains generally agree with the depth estimates in the new geologic model. The deconvolution depth estimates also show that the concealed Patagonia Fault southwest of the Patagonia Mountains is more complex than recent geologic mapping represents. Additionally, Euler deconvolution depth estimates with a structural index of 2 locate many potential intrusive bodies that might be associated with known and unknown mineralization.

Assessment of the Old Red Rock Indian Line Sycamore Tree, Lake Red Rock, Marion County, Iowa

DTIC Science & Technology

1992-01-01

miles, when reduced to a straight line , from the junction of the White Breast and Des Moines (Stiles 1911:4). George W. Harrison was instructed to...AD-A255 372 Assessment of the Old Red Rock Indian Line Sycamore Tree, Lake Red Rock, Marion County, Iowa DACW25-92-M-0414 by Leah D. Rogers Project...portion of tree 22 9. Map showing location of Red Rock line within treaty cession area of 23 1842 10. Portion of 1844 map showing incorrect placement of

The changing of coastal landform at Chikou barrier island and lagoon coast, Tainan, Southwestern Taiwan

NASA Astrophysics Data System (ADS)

Jen, C.-H.; Chyi, S.-J.; Hsiao, L.-L.; Wu, M.-S.; Lei, H.-F.

2012-04-01

The coast of southwestern Taiwan is mainly made of barriers and lagoons, which are prone to erosional and depositional processes. By using a serial maps, historical survey data, and RTK-GPS survey data, the changes of coast landforms are depicted. The maps being used in this study include (1) 1904 map(1:50000 scale), (2) 1920 map (1:50000 scale), (3) 1921 map (1:25000 scale), (4) 1924 map (1:25000 scale), (5) 1956 map (1:25000 scale), (6) 1975 map with ortho-rectified image (1:5000 scale), (7) 1983 map with ortho-rectified image (1:5000 scale), (8) 1989 map with ortho-rectified image (1:5000 scale), (9) 1992 map with ortho-rectified image (1:5000 scale), (10) 2001 map with ortho-rectified image (1:5000 scale). All maps are scanned and georeferenced to build a GIS archive for digitizing and further analysis. The results show that this coast was made of continuous sand barriers and lagoons. While lagoons were gradually shrinking, the sand barriers had remained stable from 1904 to 1924. After that, lagoons substantially deposited in the southern part and sand barriers became landward. In 1975 map, lagoons vanished and replaced with a tidal flat and tidal creeks. The following maps show that lagoons start to form again and sand barriers moving landward continuously. It is a significant sign of serious erosion in the coast. The RTK-GPS survey data in recent years show more detail of coast erosion and landform changes. The post-typhoon investigation results show that the seaward side of barrier island is eroded largely, especially for the two segments of the central part of the barrier island. Some depositions were found on the top of northern and central part of barrier dune, as well as washovers. In the southern barrier island, the depositions were carried to backshore and were obstructed in front of the bamboo piles and marine solid bags. The survey indicated the areas eroded by storm surge were gradually accumulating except for the beaches separate with plastic sheet piles and marine solid bags, especially the northern section-north, after the Typhoon Megi happened two month. In late February of 2011, there are some deposition on the top of primary dune, backdune and tidal flat. But the parts of seaward beach which wave can reach are continuously eroded, especially the central segment of the barrier island is mostly vulnerable. In particular, the latter part of southern beach was accumulated, concerning with alongshore current transport. In the late winter monsoon season, elevation changes are smaller than in the medium, corresponding with the wave condition. The latter part of south section begin to be eroded, the sediments may be taken away by the southward current. Area A, located the central of barrier island, attacked by wave continuously, elevation of dune decrease constantly, and then overwashed frequently. Keywords: sand barrier and lagoon coast, archive map analysis, RTK-GPS survey, overwash

Satellite Radar Show Complex Set of Faults Moved in 2016 New Zealand Earthquake

NASA Image and Video Library

2017-03-23

NASA and its partners are contributing important observations and expertise to the ongoing response to the Nov. 14, 2016, magnitude 7.8 Kaikoura earthquake in New Zealand. This shallow earthquake was so complex and unusual, it is likely to change how scientists think about earthquake hazards in plate boundary zones around the world. Scientists with the Advanced Rapid Imaging and Analysis project (ARIA), a collaboration between NASA's Jet Propulsion Laboratory, Pasadena, California, and Caltech in Pasadena, analyzed interferometric synthetic aperture radar images from the PALSAR-2 instrument on the ALOS-2 satellite operated by the Japan Aerospace Exploration Agency (JAXA) to calculate maps of the deformation of Earth's surface caused by the quake. Two maps show motion of the surface in two different directions. Each false-color map shows the amount of permanent surface movement caused almost entirely by the earthquake, as viewed by the satellite, during a 28-day interval between two ALOS-2 wide-swath images acquired on Oct. 18 and Nov. 15, 2016. In these two new maps made from the wide-swath images, the colors of the surface displacements are proportional to the surface motion. The wide-swath images cover the entire 106-mile (170-kilometer) length of the complex set of earthquake ruptures. The arrows show the direction of the radar motion measurement. In the left image, the blue and purple tones show the areas where the land around the Kaikoura peninsula in the Marlborough region of New Zealand's South Island has moved toward the satellite by up to 13.2 feet (4 meters), both eastward and upward. In the right image, the blue and purple tones show the areas that moved to the north by up to 30 feet (9 meters) and green tones show the area that moved to the south. The sharp line of color change is across the Kekerengu Fault, which had the largest amount of motion in the earthquake. Field studies found maximum rupture at the surface was measured at 39 feet (12 meters) of horizontal displacement. Several other faults have sharp color changes due to smaller amounts of motion, with a total of at least 12 faults rupturing in this single large earthquake. Areas without color have snow, heavy vegetation or open water that prevents the radar measurements from being coherent between satellite images – a required condition to measure ground displacement. Scientists use these maps to build detailed models of the fault slip at depth and associated land movements to better understand the impact on future earthquake activity. The PALSAR-2 data were provided by JAXA through the Committee on Earth Observation Satellites (CEOS) and through scientific research projects. The background image is from Google Earth. http://photojournal.jpl.nasa.gov/catalog/PIA21210

Airborne gamma-ray spectrometer and magnetometer survey, Durango B, Colorado. Final report Volume II C. Detail area

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1983-01-01

This volume contains eight appendices: flight line maps, geology maps, explanation of geologic legend, flight line/geology maps, radiometric contour maps, magnetic contour maps, multi-variant analysis maps, and geochemical factor analysis maps. These appendices pertain to the Durango B detail area.

Evaluation of LiDAR Imagery as a Tool for Mapping the Northern San Andreas Fault in Heavily Forested Areas of Mendocino and Sonoma Counties, California

NASA Astrophysics Data System (ADS)

Prentice, C. S.; Koehler, R. D.; Baldwin, J. N.; Harding, D. J.

2004-12-01

We are mapping in detail active traces of the San Andreas Fault in Mendocino and Sonoma Counties in northern California, using recently acquired airborne LiDAR (also known as ALSM) data. The LiDAR data set provides a powerful new tool for mapping geomorphic features related to the San Andreas Fault because it can be used to produce high-resolution images of the ground surfaces beneath the forest canopy along the 70-km-long section of the fault zone encompassed by the data. Our effort represents the first use of LiDAR data to map active fault traces in a densely vegetated region along the San Andreas Fault. We are using shaded relief images generated from bare-earth DEMs to conduct detailed mapping of fault-related geomorphic features (e.g. scarps, offset streams, linear valleys, shutter ridges, and sag ponds) between Fort Ross and Point Arena. Initially, we map fault traces digitally, on-screen, based only on the geomorphology interpreted from LiDAR images. We then conduct field reconnaissance using the initial computer-based maps in order to verify and further refine our mapping. We found that field reconnaissance is of utmost importance in producing an accurate and detailed map of fault traces. Many lineaments identified as faults from the on-screen images were determined in the field to be old logging roads or other features unrelated to faulting. Also, in areas where the resolution of LiDAR data is poor, field reconnaissance, coupled with topographic maps and aerial photographs, permits a more accurate location of fault-related geomorphic features. LiDAR images are extremely valuable as a base for field mapping in this heavily forested area, and the use of LiDAR is far superior to traditional mapping techniques relying only on aerial photography and 7.5 minute USGS quadrangle topographic maps. Comparison with earlier mapping of the northern San Andreas fault (Brown and Wolfe, 1972) shows that in some areas the LiDAR data allow a correction of the fault trace location of up to several hundred meters. To date we have field checked approximately 24 km of the 70-km-long section of the fault for which LiDAR data is available. The remaining 46 km will be field checked in 2005. The result will be a much more accurate map of the active traces of the northern San Andreas Fault, which will be of great use for future fault studies.

Preliminary maps showing ground-water resources in the Lower Colorado River region, Arizona, Nevada, New Mexico, and Utah

USGS Publications Warehouse

Brown, S.G.

1976-01-01

This atlas was prepared to meet the need for information on the areal distribution, quantity, and availability of ground water in the lower Colorado River region, an area of about 140,000 square miles in parts of Arizona, Nevada, New Mexico, and Utah. The maps are necessarily generalized in places owing to the lack of sufficient data. In general the geohydrologic information pertains to large areas, and local exceptions occur. Users needing more detailed information for specific areas may address inquiries to the district chief of the U.S. Geological Survey at the addresses given in the section “Selected References.” The maps were prepared using data from previously published reports, data collected by other Federal State, and local agencies, and data from the files of the U.S. Geological Survey offices in Arizona, Nevada, New Mexico, and Utah. The report is the result of the lower Colorado River region Type I framework study made in cooperation with the U.S. Bureau of Reclamation.

Spatial frequency-dependent feedback of visual cortical area 21a modulating functional orientation column maps in areas 17 and 18 of the cat.

PubMed

Huang, Luoxiu; Chen, Xin; Shou, Tiande

2004-02-20

The feedback effect of activity of area 21a on orientation maps of areas 17 and 18 was investigated in cats using intrinsic signal optical imaging. A spatial frequency-dependent decrease in response amplitude of orientation maps to grating stimuli was observed in areas 17 and 18 when area 21a was inactivated by local injection of GABA, or by a lesion induced by liquid nitrogen freezing. The decrease in response amplitude of orientation maps of areas 17 and 18 after the area 21a inactivation paralleled the normal response without the inactivation. Application in area 21a of bicuculline, a GABAa receptor antagonist caused an increase in response amplitude of orientation maps of area 17. The results indicate a positive feedback from high-order visual cortical area 21a to lower-order areas underlying a spatial frequency-dependent mechanism.

Using Vegetation Maps to Provide Information on Soil Distribution

NASA Astrophysics Data System (ADS)

José Ibáñez, Juan; Pérez-Gómez, Rufino; Brevik, Eric C.; Cerdà, Artemi

2016-04-01

Many different types of maps (geology, hydrology, soil, vegetation, etc.) are created to inventory natural resources. Each of these resources is mapped using a unique set of criteria, including scales and taxonomies. Past research has indicated that comparing the results of different but related maps (e.g., soil and geology maps) may aid in identifying deficiencies in those maps. Therefore, this study was undertaken in the Almería Province (Andalusia, Spain) to (i) compare the underlying map structures of soil and vegetation maps and (ii) to investigate if a vegetation map can provide useful soil information that was not shown on a soil map. To accomplish this soil and vegetation maps were imported into ArcGIS 10.1 for spatial analysis. Results of the spatial analysis were exported to Microsoft Excel worksheets for statistical analyses to evaluate fits to linear and power law regression models. Vegetative units were grouped according to the driving forces that determined their presence or absence (P/A): (i) climatophilous (climate is the only determinant of P/A) (ii); lithologic-climate (climate and parent material determine PNV P/A); and (iii) edaphophylous (soil features determine PNV P/A). The rank abundance plots for both the soil and vegetation maps conformed to Willis or Hollow Curves, meaning the underlying structures of both maps were the same. Edaphophylous map units, which represent 58.5% of the vegetation units in the study area, did not show a good correlation with the soil map. Further investigation revealed that 87% of the edaphohygrophylous units (which demand more soil water than is supplied by other soil types in the surrounding landscape) were found in ramblas, ephemeral riverbeds that are not typically classified and mapped as soils in modern systems, even though they meet the definition of soil given by the most commonly used and most modern soil taxonomic systems. Furthermore, these edaphophylous map units tend to be islands of biodiversity that are threatened by anthropogenic activity in the region. Therefore, this study revealed areas in Almería Province that need to be revisited and studied pedologically. The vegetation mapped in these areas and the soils that support it are key components of the earth's critical zone that must be studied, understood, and preserved.

Critical metals in manganese nodules from the Cook Islands EEZ, abundances and distributions

USGS Publications Warehouse

Hein, James R.; Spinardi, Francesca; Okamoto, Nobuyuki; Mizell, Kira; Thorburn, Darryl; Tawake, Akuila

2015-01-01

Compiled data from a series of four cruises by the Japan International Cooperation Agency and the Mining agency of Japan from 1985 to 2000 were used to generate a map that defines the statistical distribution of nodule abundance throughout the EEZ, except the Manihiki Plateau. The abundance distribution map shows a belt of high nodule abundance (19–45 kg/m2) that starts in the southeast corner of the EEZ, runs northwest, and also bifurcates into a SW trending branch. Small, isolated areas contain abundances of nodules of up to 58 kg/m2. Six ~ 20,000 km2 areas of particularly high abundance were chosen to represent potential exploration areas, and maps for metal concentration were generated to visualize metal distribution and to extrapolate estimated metal tonnages within the six sites and the EEZ as a whole. Grades for Mn, Cu, and Ni are low in CIs nodules in areas of high abundance; however, Ti, Co, and REY show high contents where nodule abundances are high. Of the six areas identified to represent a range of metal contents, one at the northern end of the N-S abundance main belt optimizes the most metals and would yield the highest dry metric tons for Mn (61,002,292), Ni (1,247,834), Mo (186,166), V (356,247), W (30,215), and Zr (195,323). When compared with the Clarion–Clipperton Zone, the CIs nodules show higher nodule abundances (> 25 kg/m2 over ~ 123,844 km2), and are more enriched in the green-tech, high-tech, and energy metals Co, Ti, Te, Nb, REY, Pt, and Zr. The CIs EEZ shows a significant resource potential for these critical metals due to their high prices, high demand, and the high nodule abundance, which will allow for a smaller footprint for a 20-year mine site and therefore smaller environmental impact.