Polyethylenimine-magadiite layered silicate sorbent for CO2 capture.

PubMed

Vieira, Rômulo B; Pastore, Heloise O

2014-02-18

This paper describes the preparation of a Layered Silicate Sorbent (LSS) for CO2 capture using the layered silicate magadiite and organo-magadiite modified with polyethylenimine (PEI). The sorbents were characterized and revealed the presence of PEI as well as its interaction with CO2 at low temperatures. The thermal stability of sorbents was confirmed by thermogravimetry experiments, and the adsorption capacity was evaluated by CO2-TPD experiments. Two kinds of PEI are present in the sorbent, one exposed PEI layer that is responsible for higher CO2 adsorption because its sites are external and another one, bulky PEI, capable of low CO2 adsorption due to the internal position of sites. The contribution of the exposed PEI layer may be increased by a previous exchange of CTA(+), but the presence of the surfactant decreased the total adsorption capacity. MAG-PEI25 reached a maximum adsorption capacity of 6.11 mmol g(-1) at 75 °C for 3 h of adsorption and showed a kinetic desorption of around 15 min at 150 °C.

Disappearance of 19P/Borrelly's Silicate Feature in 2001 Apparition Is Attributed to Increase in Grain Size

NASA Astrophysics Data System (ADS)

Wooden, D. H.; Woodward, C. E.; Harker, D. E.

2003-05-01

We report on observations and analysis of HIFOGS 10 \\micron \\ spectrophotometry of short period comet 19P/Borrelly on 2003 October 13, 15 UT at the NASA IRTF. 19P/Borrelly is one of two short period comets, comet 4P/Faye being the other, to have a silicate feature detected (Hanner et al. 1996, Icarus, 124, 344). During Borrelly.s perihelion passage in 1994 December, a silicate feature was present with a flux-to-continuum ratio of 0.25. Two apparitions later in 2003 October, the silicate feature is absent. Thermal emission modeling (cf. Harker et al. 2002, ApJ, 580, 579) using amorphous olivine and amorphous carbon shows that a slight increase in grain size accounts for the disappearance of the silicate feature. Analysis of 19P/Borrelly suggests grain size, and not the absence of olivine minerals, may be responsible for the absence of silicate features in most short period comets. 19P/Borrelly is one of the more active short period comets. However, short period comets as a family are less active than long period comets. Short period comets probably originated in the Kuiper Belt and suffered collisions while in residence in the outer solar system. Upon evolution into orbits that take them through the inner solar system, the surfaces of short period comets are exposed to sunlight through their many perihelion passages. This is in contrast to long period comets which probably originated near Jupiter and were expelled to the Oort cloud where they have existed and been exposed to cosmic ray processing. By studying the grain properties in short period comets and comparing to long period comets, we compare the effects on the grain populations of different parent body evolution histories. Upcoming opportunities to study short and long period comets will be advertised. This research is supported in part by an NSF Grant to the University of Minnesota.

Mapping the Spatial Distribution of Metal-Bearing Oxides in VY Canis Majoris

NASA Astrophysics Data System (ADS)

Burkhardt, Andrew; Booth, S. Tom; Remijan, Anthony; Carroll, Brandon; Ziurys, Lucy M.

2015-06-01

The formation of silicate-based dust grains is not well constrained. Despite this, grain surface chemistry is essential to modern astrochemical formation models. In carbon-poor stellar envelopes, such as the red hypergiant VY Canis Majoris (VY CMa), metal-bearing oxides, the building blocks of silicate grains, dominate the grain formation, and thus are a key location to study dust chemistry. TiO_2, which was only first detected in the radio recently (Kaminski et al., 2013a), has been proposed to be a critical molecule for silicate grain formation, and not oxides containing more abundant metals (eg. Si, Fe, and Mg) (Gail and Sedlmayr, 1998). In addition, other molecules, such as SO_2, have been found to trace shells produced by numerous outflows pushing through the expanding envelope, resulting in a complex velocity structure (Ziurys et al., 2007). With the advanced capabilities of ALMA, it is now possible to individually resolve the velocity structure of each of these outflows and constrain the underlying chemistry in the region. Here, we present high resolution maps of rotational transitions of several metal-bearing oxides in VY CMa from the ALMA Band 7 and Band 9 Science Verification observations. With these maps, the physical parameters of the region and the formation chemistry of metal-bearing oxides will be studied.

Delineation of Magnesium-rich Ultramafic Rocks Available for Mineral Carbon Sequestration in the United States

USGS Publications Warehouse

Krevor, S.C.; Graves, C.R.; Van Gosen, B. S.; McCafferty, A.E.

2009-01-01

The 2005 Intergovernmental Panel on Climate Change report on Carbon Dioxide Capture and Storage suggested that a major gap in mineral carbon sequestration is locating the magnesium-silicate bedrock available to sequester CO2. It is generally known that silicate minerals with high concentrations of magnesium are suitable for mineral carbonation. However, no assessment has been made covering the entire United States detailing their geographical distribution and extent, or evaluating their potential for use in mineral carbonation. Researchers at Columbia University and the U.S. Geological Survey have developed a digital geologic database of ultramafic rocks in the continental United States. Data were compiled from varied-scale geologic maps of magnesium-silicate ultramafic rocks. These rock types are potentially suitable as source material for mineral carbon-dioxide sequestration. The focus of the national-scale map is entirely on suitable ultramafic rock types, which typically consist primarily of olivine and serpentine minerals. By combining the map with digital datasets that show non-mineable lands (such as urban areas and National Parks), estimates on potential depth of a surface mine, and the predicted reactivities of the mineral deposits, one can begin to estimate the capacity for CO2 mineral sequestration within the United States. ?? 2009 Elsevier Ltd. All rights reserved.

Silicon based substrate with calcium aluminosilicate/thermal barrier layer

NASA Technical Reports Server (NTRS)

Eaton, Jr., Harry Edwin (Inventor); Allen, William Patrick (Inventor); Miller, Robert Alden (Inventor); Jacobson, Nathan S. (Inventor); Smialek, James L. (Inventor); Opila, Elizabeth J. (Inventor); Lee, Kang N. (Inventor); Nagaraj, Bangalore A. (Inventor); Wang, Hongyu (Inventor); Meschter, Peter Joel (Inventor)

2001-01-01

A barrier layer for a silicon containing substrate which inhibits the formation of gaseous species of silicon when exposed to a high temperature aqueous environment comprises a calcium alumino silicate.

Silicon based substrate with environmental/thermal barrier layer

NASA Technical Reports Server (NTRS)

Eaton, Jr., Harry Edwin (Inventor); Allen, William Patrick (Inventor); Jacobson, Nathan S. (Inventor); Bansal, Narottam P. (Inventor); Opila, Elizabeth J. (Inventor); Smialek, James L. (Inventor); Lee, Kang N. (Inventor); Spitsberg, Irene T. (Inventor); Wang, Hongyu (Inventor); Meschter, Peter Joel (Inventor)

2002-01-01

A barrier layer for a silicon containing substrate which inhibits the formation of gaseous species of silicon when exposed to a high temperature aqueous environment comprises a barium-strontium alumino silicate.

Silicon based substrate with environmental/ thermal barrier layer

NASA Technical Reports Server (NTRS)

Eaton, Jr., Harry Edwin (Inventor); Allen, William Patrick (Inventor); Jacobson, Nathan S. (Inventor); Bansal, Nanottam P. (Inventor); Opila, Elizabeth J. (Inventor); Smialek, James L. (Inventor); Lee, Kang N. (Inventor); Spitsberg, Irene T. (Inventor); Wang, Hongyu (Inventor); Meschter, Peter Joel (Inventor)

2002-01-01

A barrier layer for a silicon containing substrate which inhibits the formation of gaseous species of silicon when exposed to a high temperature aqueous environment comprises a barium-strontium alumino silicate.

Imaging of drug loading distributions in individual microspheres of calcium silicate hydrate - an X-ray spectromicroscopy study

NASA Astrophysics Data System (ADS)

Guo, Xiaoxuan; Wang, Zhiqiang; Wu, Jin; Wang, Jian; Zhu, Ying-Jie; Sham, Tsun-Kong

2015-04-01

Imaging is one of the most direct and ideal ways to track drug loading distributions in drug carriers on the molecular level, which will facilitate the optimization of drug carriers and drug loading capacities. Herein, we report the mapping of an individual mesoporous calcium silicate hydrate (CSH) microsphere before and after the loading of ibuprofen (IBU) and the interactions between drug carriers and drug molecules simultaneously by scanning transmission X-ray microscopy (STXM). Nanoscaled X-ray absorption near edge structure (XANES) spectroscopy clearly indicates that IBU is bonded to calcium and silicate sites via carboxylic acid groups. More importantly, STXM has been successfully used to determine the absolute thickness of IBU, revealing its distribution in the CSH microsphere.Imaging is one of the most direct and ideal ways to track drug loading distributions in drug carriers on the molecular level, which will facilitate the optimization of drug carriers and drug loading capacities. Herein, we report the mapping of an individual mesoporous calcium silicate hydrate (CSH) microsphere before and after the loading of ibuprofen (IBU) and the interactions between drug carriers and drug molecules simultaneously by scanning transmission X-ray microscopy (STXM). Nanoscaled X-ray absorption near edge structure (XANES) spectroscopy clearly indicates that IBU is bonded to calcium and silicate sites via carboxylic acid groups. More importantly, STXM has been successfully used to determine the absolute thickness of IBU, revealing its distribution in the CSH microsphere. Electronic supplementary information (ESI) available. See DOI: 10.1039/c4nr07471h

Silicon based substrate with calcium aluminosilicate environmental/thermal barrier layer

NASA Technical Reports Server (NTRS)

Eaton, Jr., Harry Edwin (Inventor); Allen, William Patrick (Inventor); Miller, Robert Alden (Inventor); Jacobson, Nathan S. (Inventor); Smialek, James L. (Inventor); Opila, Elizabeth J. (Inventor); Lee, Kang N. (Inventor); Nagaraj, Bangalore A. (Inventor); Wang, Hongyu (Inventor); Meschter, Peter Joel (Inventor)

2001-01-01

A barrier layer for a silicon containing substrate which inhibits the formation of gaseous species of silicon when exposed to a high temperature aqueous environment comprises a calcium alumino silicate.

Field, petrologic and detrital zircon study of the Kings sequence and Calaveras complex, Southern Lake Kaweah Roof Pendant, Tulare County, California

NASA Astrophysics Data System (ADS)

Buchen, Christopher T.

U-Pb dating of detrital zircon grains separated from elastic sedimentary rocks is combined with field, petrographic and geochemical data to reconstruct the geologic history of Mesozoic rocks exposed at the southern end of the Lake Kaweah metamorphic pendant, western Sierra Nevada. Identification of rocks exposed at Limekiln Hill, Kern County, CA, as belonging to the Calaveras complex and Kings sequence was confirmed. Detrital zircon populations from two Calaveras complex samples provide Permo-Triassic maximum depositional ages (MDA) and reveal a Laurentian provenance indicating that continental accretion of the northwest-trending Kings-Kaweah ophiolite belt was in process prior to the Jurassic Period. Rock types including radiolarian metachert, metachert-argillite, and calc-silicate rocks with marble lenses are interpreted as formed in a hemipelagic environment of siliceous radiolarian deposition, punctuated by extended episodes of lime-mud gravity flows mixing with siliceous ooze forming cafe-silicate protoliths and limestone olistoliths forming marble lenses. Two samples of the overlying Kings sequence turbidites yield detrital zircons with an MDA of 181.4 +/-3.0 Ma and an interpreted provenance similar to other Jurassic metasediments found in the Yokohl Valley, Sequoia and Boyden Cave roof pendants. Age peaks indicative of Jurassic erg heritage are also present. In contrast, detrital zircon samples from the Sequoia and Slate Mountain roof pendants bear age-probability distributions interpreted as characteristic of the Snow Lake block, a tectonic sliver offset from the Paleozoic miogeocline.

Mapping the Mineral Resource Base for Mineral Carbon-Dioxide Sequestration in the Conterminous United States

USGS Publications Warehouse

Krevor, S.C.; Graves, C.R.; Van Gosen, B. S.; McCafferty, A.E.

2009-01-01

This database provides information on the occurrence of ultramafic rocks in the conterminous United States that are suitable for sequestering captured carbon dioxide in mineral form, also known as mineral carbon-dioxide sequestration. Mineral carbon-dioxide sequestration is a proposed greenhouse gas mitigation technology whereby carbon dioxide (CO2) is disposed of by reacting it with calcium or magnesium silicate minerals to form a solid magnesium or calcium carbonate product. The technology offers a large capacity to permanently store CO2 in an environmentally benign form via a process that takes little effort to verify or monitor after disposal. These characteristics are unique among its peers in greenhouse gas disposal technologies. The 2005 Intergovernmental Panel on Climate Change report on Carbon Dioxide Capture and Storage suggested that a major gap in mineral CO2 sequestration is locating the magnesium-silicate bedrock available to sequester the carbon dioxide. It is generally known that silicate minerals with high concentrations of magnesium are suitable for mineral carbonation. However, no assessment has been made in the United States that details their geographical distribution and extent, nor has anyone evaluated their potential for use in mineral carbonation. Researchers at Columbia University and the U.S. Geological Survey have developed a digital geologic database of ultramafic rocks in the conterminous United States. Data were compiled from varied-scale geologic maps of magnesium-silicate ultramafic rocks. The focus of our national-scale map is entirely on ultramafic rock types, which typically consist primarily of olivine- and serpentine-rich rocks. These rock types are potentially suitable as source material for mineral CO2 sequestration.

Geographic variation in the relationships of temperature, salinity or sigma sub t versus plant nutrient concentrations in the world ocean. [silicic acid, nitrate, and phosphate concentration

NASA Technical Reports Server (NTRS)

Kamykowski, D.; Zentara, S. J.

1985-01-01

A NODC data set representing all regions of the world ocean was analyzed for temperature and sigma-t relationships with nitrate, phosphate or silicic acid. Six cubic regressions were for each ten degree square of latitude and longitude containing adequate data. World maps display the locations that allow the prediction of plant nutrient concentrations from temperature or sigma-t. Geographic coverage improves along the sequence: nitrate, phosphate, and silicic acid and is better for sigma-t than for temperature. Contour maps of the approximate temperature of sigma-t at which these nitrients are no longer measurable in a parcel of water are generated, based on a percentile analysis of the temperature or sigma-t at which less than a selected amount of plant nutrient occurs. Results are stored on magnetic tape in tabular form. The global potential to predict plant nutrient concentrations from remotely sensed temperature of sigma-t and to emphasize the latitudinally and longitudinally changing phytoplankton growth environment in present and past oceans is demonstrated.

The Puelche volcanic field: Extensive Pleistocene rhyolite lava flows in the Andes of central Chile

USGS Publications Warehouse

Hildreth, W.; Fierstein, J.; Godoy, E.; Drake, Robert E.; Singer, B.

1999-01-01

A remote volcanic field in the rugged headwaters of the Rio Puelche and Rio Invernada (35.8??S) constitutes the largest cluster of Quaternary rhyolite lava flows yet identified in the Andean Southern Volcanic Zone. The Puelche Volcanic Field belongs to an intra-arc belt of silicic magmatic centers that extends, at least, 140 km north-south and lies well east of the volcanic front but nonetheless considerably west of the intraplate extensional fields of basaltic and alkaline centers of pampean Argentina. The authors' mapping has distinguished one shallow intrusive mass of early Pleistocene biotite rhyodacite (70.5% SiO2), 11 eruptive units of mid-Pleistocene high-K biotite-rhyolite lava (71.3-75.6% SiO2), and 4 eruptive units of basaltic andesite (53.95-4.9% SiO2), the conduits of which cut some of the rhyolites. Basal contacts of the rhyolite lava flows (and subjacent pyroclastic precursors) are generally scree covered, but glacial erosion has exposed internal flow structures and lithologic zonation superbly. Thicknesses of individual rhyolite lava flows range from 75 m to 400 m. Feeders for several units are well exposed. Cliff-draping unconformities and intracanyon relationships among the 11 rhyolite units show that the eruptive sequence spanned at least one glacial episode that accentuated the local relief. Lack of ice-contact features suggests, however, that all or most eruptions took place during non-glacial intervals probably between 400 ka and 100 ka. Post-eruptive glacial erosion reduced the rhyolites to several non-contiguous remnants that altogether cover 83 km2 and represent a surviving volume of about 21 km3. Consideration of slopes, lava thicknesses, and paleotopography suggest that the original area and volume were each about three times greater. Phenocryst content of the rhyolites ranges from 1 to 12%, with plagioclase>>biotite>FeTi oxides in all units and amphibole conspicuous in the least silicic. The chemically varied basaltic andesites range from phenocryst-poor to phenocryst-rich, exhibiting large differences in proportions of clinopyroxene, olivine, plagioclase, and xenocrystic quartz. Compositional bimodality of the volcanic field is striking, there being no Quaternary eruptive units having SiO2 contents between 55 and 70%. Major and trace element compositions of the mafic and silicic rocks are nonetheless typical of continental-margin arc suites, not of intracontinental suites. The lack of intermediate eruptive units and the differences between the mafic and rhyolitic lavas in Sr-isotope composition suggest that the rhyolites fractionated from a hybrid parent rather than continuously from basaltic magma. The rhyolites may contain larger contributions of upper-crustal partial melts than do silicic products of the volcanic-front centers 30 km to the west.

Nature and time of emplacement of a pegmatoidal granite within the Delhi Fold Belt near Bayalan, Rajasthan, India

NASA Astrophysics Data System (ADS)

Dasgupta, N.; Sen, J.; Pal, T.; Ghosh, T.

2009-04-01

The study area is situated about 70 km south east of Ajmer, in Rajasthan, India around the village Bayala (26o 02' 19 N''; 74o 21' 01'') within the Ajmer district of Central Rajasthan. The area is along the eastern flank of the central portion of the Precambrian South Delhi Fold Belt (SDFB) and it stratigraphically belongs to the Bhim Group of rocks. Basement rocks of Archaean age, commonly known as the Banded gneissic Complex (BGC), is exposed to the east, where the rocks of the Bhim Group rests unconformably over BGC. To the west gneissic basement rocks of mid-Proterozoic times underlie the Bhim Group and have been referred to as the Beawar gneiss (BG). The Bhim Group of rocks comprises of metamorphosed marls and calc-silicate gneisses with minor amounts of quartzites and pelitic schists, indicative of its shallow marine origin. Within the Bhim Group, a pegmatoidal granite has intruded the calc silicate gneisses of the area. The pegmatoidal granite body is elliptical in outline with the long dimension(20 km) trending N-S and covers an area of 300 sq. km. approximately. This granite have so far been mapped as basement rocks (BG) surrounding the Beawar town (26o 06' 05'' N; 74o 19' 03'' E), 50 km south east of Ajmer. Rafts of calc-silicate gneisses, belonging to the Bhim Group, are seen to be entrapped within granite. Fragments of BG and its equivalents have also been found as caught up blocks within this pegmatoidal granite body near Andheri Devari, a small hamlet east of Beawar. The objective of the study was to map this pegmatoidal body, and decipher the mechanism and time of emplacement of this granite. A detailed structural mapping of the area in a 1:20000 scale spread over a 30 sq. km area in the vicinity of Bayala was carried out to analyse the geometry and the time of emplacement of the pegmatitic granite. The ridges of calc silicates and marbles adjoining the area were studied for the structural analyses of the Delhi fold belt rocks of the area. The calc silicate gneisses of the Bhim Group have been deformed by three major phases of folding, namely D1, D2 and D3. Of these the D1 folds defined by transposed compositional layering are intrafolial and isoclinal in nature. The D2 folds are asymmetric with alternate steeply and gently easterly dipping limbs and are defined by compositional banding and schistosity (S1). A good compositional layering parallel to the S2 fabric has been observed within the calc silicate gneisses. The D2 folds are close to tight, gently plunging with a modal plunge of 20o towards 40o; and has an inclined axial plane which has an easterly vergence. This is the most dominant phase of deformation. The D3 folds have developed on the gentle limbs of the D2 folds with a horizontal axis on a vertical axial plane. Interference of the D1 with D2 and D1 with D3 has produced Type III type of interference pattern. The pegmatitic granite body is a coarse grained rock composed of quartz feldspar (dominantly K-feldspar), muscovite, biotite, and tourmaline. A weak foliation has developed within this rock which is parallel to the D3 axial planar structure found within the calc silicate gneisses. Thus from the structural study it is proposed that the pegmatitic granite was emplaced post-D2 and possibly syn D3. The presence of narrow planar zones of hornfelsic rocks parallel to the D3 axial plane within the calc silicate rocks also attests to the above fact. Therefore the D3 axial planes provided the necessary conduits of the granite fluid movement within the calcsilicate rocks. The intrusions have scaled off the calc silicate gneisses into large continuous pieces along the gneissosity plane and got emplaced along the hinges of the D2 and D3 folds. Though disturbed, it has been seen that the orientation of the structural elements within these ripped off blocks of the calc silicate gneisses were quite similar to those found within the ridges, unaffected by the granite. The granites were thus emplaced lit-par-lit in the country rocks and on their contact with the calc gneisses shows hornfelsic textures within the calcsilicates (Tremolite-actinolite schists). It is thought of that this pegmatoidal granite has a bearing in age with the wide scale granite activity seen within this region. The structural study shows that this pegmatitic granite was emplaced synchronous to the D3 deformation episode which is the last major recognizable deformation within the Delhi Orogeny. Therefore this pegmatitic granite marks the closing stages of the Delhi Orogeny. Combined with the 1 Ga age of the formation of crust, in the western segment of the Delhi basin, a proper dating of this granite could give us the exact time span of the delhi orogenic cycle.

Non-fibrous inorganic particles in bronchoalveolar lavage fluid of pottery workers.

PubMed Central

Falchi, M; Paoletti, L; Mariotta, S; Giosue, S; Guidi, L; Biondo, L; Scavalli, P; Bisetti, A

1996-01-01

AIM: To study the actual exposure of pottery workers to silica particles, as their risk of silicosis is potentially high because of the presence of inhalable crystalline silica particles in the workplace. METHODS: Nine pottery workers underwent bronchoalveolar lavage. The recovered fluid was analysed for cytological and mineralogical content by analytical transmission electron microscopy. The data were compared with those obtained from a control group composed of seven patients with sarcoidosis and six patients with haemoptysis. RESULTS: Cytological results showed a similar profile in exposed workers and controls, whereas in patients with sarcoidosis a lymphocytic alveolitis was found. Microanalysis of the particulate identified the presence of silicates, CRSs, and metals. Pottery workers had higher numbers of total particles and CRSs, and had a higher silicate/metal ratio. In five workers, the presence of zirconium silicate was also detected. Patients with sarcoidosis had the lowest number of particles, and an inverted silicate/metal ratio. CONCLUSION: Microanalysis by transmission electron microscope can provide useful information to assess occupational exposure to dusts. PMID:9038801

Lithologic mapping of silicate rocks using TIMS

NASA Technical Reports Server (NTRS)

Gillespie, A. R.

1986-01-01

Common rock-forming minerals have thermal infrared spectral features that are measured in the laboratory to infer composition. An airborne Daedalus scanner (TIMS) that collects six channels of thermal infrared radiance data (8 to 12 microns), may be used to measure these same features for rock identification. Previously, false-color composite pictures made from channels 1, 3, and 5 and emittance spectra for small areas on these images were used to make lithologic maps. Central wavelength, standard deviation, and amplitude of normal curves regressed on the emittance spectra are related to compositional information for crystalline igneous silicate rocks. As expected, the central wavelength varies systematically with silica content and with modal quartz content. Standard deviation is less sensitive to compositional changes, but large values may result from mixed admixture of vegetation. Compression of the six TIMS channels to three image channels made from the regressed parameters may be effective in improving geologic mapping from TIMS data, and these synthetic images may form a basis for the remote assessment of rock composition.

Interactions of silicate glasses with aqueous environments under conditions of prolonged contact and flow

NASA Technical Reports Server (NTRS)

Barkatt, Aaron; Saad, E. E.; Adiga, R. B.; Sousanpour, W.; Barkatt, AL.; Feng, X.; O'Keefe, J. A.; Alterescu, S.

1988-01-01

This paper discusses mechanisms involving saturation and reactions that lead to the formation of altered phases in silicate glasses considered for use in geologic repositories for nuclear waste. It is shown that the rate of dissolution of silicate glasses exposed to a broad range of contact times, leachant compositions, and surface-to-volume ratios is strongly affected by the presence of reactive species such as Al, Mg, and Fe. The reactive materials may originate in the leachant or, under conditions of high surface-to-volume ratio, in the glass itself. The effects of glass composition on the course of the corrosion process can be viewed in terms of the formation of a surface layer on the leached glass; the type, composition, and structure of this layer control the dissolution behavior of the glass.

Geologic map of the Strawberry Butte 7.5’ quadrangle, Meagher County, Montana

USGS Publications Warehouse

Reynolds, Mitchell W.; Brandt, Theodore R.

2017-06-19

The 7.5′ Strawberry Butte quadrangle in Meagher County, Montana near the southwest margin of the Little Belt Mountains, encompasses two sharply different geologic terranes.  The northern three-quarters of the quadrangle are underlain mainly by Paleoproterozoic granite gneiss, across which Middle Cambrian sedimentary rocks rest unconformably.  An ancestral valley of probable late Eocene age, eroded northwest across the granite gneiss terrane, is filled with Oligocene basalt and overlying Miocene and Oligocene sandstone, siltstone, tuffaceous siltstone, and conglomerate.  The southern quarter of the quadrangle is underlain principally by deformed Mesoproterozoic sedimentary rocks of the Newland Formation, which are intruded by Eocene biotite hornblende dacite dikes.  In this southern terrane, Tertiary strata are exposed only in a limited area near the southeast margin of the quadrangle.  The distinct terranes are juxtaposed along the Volcano Valley fault zone—a zone of recurrent crustal movement beginning possibly in Mesoproterozoic time and certainly established from Neoproterozoic–Early Cambrian to late Tertiary time.  Movement along the fault zone has included normal faulting, the southern terrane faulted down relative to the northern terrane, some reverse faulting as the southern terrane later moved up against the northern terrane, and lateral movement during which the southern terrane likely moved west relative to the northern terrane.  Near the eastern margin of the quadrangle, the Newland Formation is locally the host of stratabound sulfide mineralization adjacent to the fault zone; west along the fault zone across the remainder of the quadrangle are significant areas and bands of hematite and iron-silicate mineral concentrations related to apparent alteration of iron sulfides.  The map defines the distribution of a variety of surficial deposits, including the distribution of hematite-rich colluvium and iron-silicate boulders.  The southeast corner of the quadrangle is the site of active exploration and potential development for copper from the sulfide-bearing strata of the Newland Formation.

Aeromagnetic map of the Fossil Springs Roadless Area, Yavapai, Gila, and Coconino counties, Arizona

USGS Publications Warehouse

Davis, W.E.; Weir, G.W.

1984-01-01

The magnetic anomalies and patterns on the aeromagnetic map reflect variations of magnetization in the underlying rocks. Basaltic rocks contain moderate amounts of magnetic minerals, mainly magnetite, and possess strong intensities of magnetization. The more silicic volcanic rocks have much lower magnetization intensities. Sedimentary rocks contain little or no magnetite and are virtually nonmagnetic.

A field trip guide to the petrology of Quaternary volcanism on the Yellowstone Plateau

USGS Publications Warehouse

Vazquez, Jorge A.; Stelten, Mark; Bindeman, Ilya N.; Cooper, Kari

2017-12-19

The Yellowstone Plateau is one of the largest manifestations of silicic volcanism on Earth, and marks the youngest focus of magmatism associated with the Yellowstone Hot Spot. The earliest products of Yellowstone Hot Spot volcanism are from ~17 million years ago, but may be as old as ~32 Ma, and include contemporaneous eruption of voluminous mafic and silicic magmas, which are mostly located in the region of northwestern Nevada and southeastern Oregon. Since 17 Ma, the main locus of Yellowstone Hot Spot volcanism has migrated northeastward producing numerous silicic caldera complexes that generally remain active for ~2–4 million years, with the present-day focus being the Yellowstone Plateau. Northeastward migration of volcanism associated with the Yellowstone Hot Spot resulted in the formation of the Snake River Plain, a low relief physiographic feature extending ~750 kilometers from northern Nevada to eastern Idaho. Most of the silicic volcanic centers along the Snake River Plain have been inundated by younger basalt volcanism, but many of their ignimbrites and lava flows are exposed in the extended regions at the margins of the Snake River Plain. 

Coordinated STEM/FIB/NanoSIMS Analyses of Presolar Silicates in Comet Dust and Primitive Meteorites

NASA Technical Reports Server (NTRS)

Keller, Lindsay; Nguyen, A.; Rahman, Z.; Messenger, S.

2012-01-01

Silicate grains were among the most abundant mineralogical building blocks of our Solar System. These grains were the detritus from earlier generations of stars that have been recycled in the early solar nebula. Rare sub-micrometer survivors of this processing have been identified in meteorites, micrometeorites and interplanetary dust particles (IDPs). These silicate grains are recognized as presolar in origin because of their extremely anomalous isotopic compositions that reflect nucleosynthetic processes in their stellar sources (evolved stars, novae and supernovae). We perform coordinated chemical, mineralogical and isotopic studies of these grains to determine their origins and histories. We examine the complex mineralogy and petrography of presolar silicates using imaging, diffraction and chemical data obtained from thin sections with the JSC JEOL 2500 field-emission STEM equipped with a Noran thin window energy dispersive x-ray (EDX) spectrometer and a Gatan Tridiem GIF. Quantitative element x-ray maps (spectrum images) are acquired by rastering a 4 nm incident probe whose dwell time is minimized to avoid beam damage and element diffusion during mapping. Successive image layers are acquired and combined in order to achieve approx 1% counting statistics for major elements. The IDP samples are prepared by ultramicrotomy of particles embedded in epoxy or elemental sulfur. After EDX mapping, the sections are subjected to C, N, and O isotopic imaging with the JSC NanoSIMS 50L ion microprobe. We prepare sections of some meteorite grains using the JSC FEI Quanta 3D focused ion beam (FIB) instrument. The specimen surface is protected from the FIB milling process by layers of electron beam-deposited C and Pt followed by an ion-deposited Pt layer. We also use the FIB to preferentially remove surrounding grains to reduce the background in subsequent NanoSIMS measurements. For mineralogical studies, we again employ the FIB instrument to deposit a protective cap over the grain of interest and then extract the grain and thin it to electron transparency for TEM analysis.

Geologic map of the central San Juan caldera cluster, southwestern Colorado

USGS Publications Warehouse

Lipman, Peter W.

2006-01-01

The San Juan Mountains are the largest erosional remnant of a composite volcanic field that covered much of the southern Rocky Mountains in middle Tertiary time. The San Juan field consists mainly of intermediate-composition lavas and breccias, erupted about 35-30 Ma from scattered central volcanoes (Conejos Formation) and overlain by voluminous ash-flow sheets erupted from caldera sources. In the central San Juan Mountains, eruption of at least 8,800 km3 of dacitic-rhyolitic magma as nine major ash flow sheets (individually 150-5,000 km3) was accompanied by recurrent caldera subsidence between 28.3 Ma and about 26.5 Ma. Voluminous andesitic-dacitic lavas and breccias erupted from central volcanoes prior to the ash-flow eruptions, and similar lava eruptions continued within and adjacent to the calderas during the period of more silicic explosive volcanism. Exposed calderas vary in size from 10 to 75 km in maximum dimension; the largest calderas are associated with the most voluminous eruptions.

Conservative approach of a symptomatic carious immature permanent tooth using a tricalcium silicate cement (Biodentine): a case report

PubMed Central

Grosgogeat, Brigitte; Seux, Dominique; Farge, Pierre

2013-01-01

The restorative management of deep carious lesions and the preservation of pulp vitality of immature teeth present real challenges for dental practitioners. New tricalcium silicate cements are of interest in the treatment of such cases. This case describes the immediate management and the follow-up of an extensive carious lesion on an immature second right mandibular premolar. Following anesthesia and rubber dam isolation, the carious lesion was removed and a partial pulpotomy was performed. After obtaining hemostasis, the exposed pulp was covered with a tricalcium silicate cement (Biodentine, Septodont) and a glass ionomer cement (Fuji IX extra, GC Corp.) restoration was placed over the tricalcium silicate cement. A review appointment was arranged after seven days, where the tooth was asymptomatic with the patient reporting no pain during the intervening period. At both 3 and 6 mon follow up, it was noted that the tooth was vital, with normal responses to thermal tests. Radiographic examination of the tooth indicated dentin-bridge formation in the pulp chamber and the continuous root formation. This case report demonstrates a fast tissue response both at the pulpal and root dentin level. The use of tricalcium silicate cement should be considered as a conservative intervention in the treatment of symptomatic immature teeth. PMID:24303363

New dust opacity maps from Viking IR thermal mapper data

NASA Technical Reports Server (NTRS)

Martin, T. Z.; Richardson, M. I.

1992-01-01

Mapping of dust opacity of the Martian atmosphere, using the silicate-induced absorption of 9 micron radiation, was performed with the Viking Infrared Thermal Mapper (IRTM) data for several local dust storms and in a global sense. We present here the first results from an effort to extend the earlier mapping work to the period of the 1977b major storm, and to concentrate attention on the details of opacity behavior during the initial phases of the 1977a and b storms.

Geologic map of the Yucca Mountain region, Nye County, Nevada

USGS Publications Warehouse

Potter, Christopher J.; Dickerson, Robert P.; Sweetkind, Donald S.; Drake II, Ronald M.; Taylor, Emily M.; Fridrich, Christopher J.; San Juan, Carma A.; Day, Warren C.

2002-01-01

Yucca Mountain, Nye County, Nev., has been identified as a potential site for underground storage of high-level radioactive waste. This geologic map compilation, including all of Yucca Mountain and Crater Flat, most of the Calico Hills, western Jackass Flats, Little Skull Mountain, the Striped Hills, the Skeleton Hills, and the northeastern Amargosa Desert, portrays the geologic framework for a saturated-zone hydrologic flow model of the Yucca Mountain site. Key geologic features shown on the geologic map and accompanying cross sections include: (1) exposures of Proterozoic through Devonian strata inferred to have been deformed by regional thrust faulting and folding, in the Skeleton Hills, Striped Hills, and Amargosa Desert near Big Dune; (2) folded and thrust-faulted Devonian and Mississippian strata, unconformably overlain by Miocene tuffs and lavas and cut by complex Neogene fault patterns, in the Calico Hills; (3) the Claim Canyon caldera, a segment of which is exposed north of Yucca Mountain and Crater Flat; (4) thick densely welded to nonwelded ash-flow sheets of the Miocene southwest Nevada volcanic field exposed in normal-fault-bounded blocks at Yucca Mountain; (5) upper Tertiary and Quaternary basaltic cinder cones and lava flows in Crater Flat and at southernmost Yucca Mountain; and (6) broad basins covered by Quaternary and upper Tertiary surficial deposits in Jackass Flats, Crater Flat, and the northeastern Amargosa Desert, beneath which Neogene normal and strike-slip faults are inferred to be present on the basis of geophysical data and geologic map patterns. A regional thrust belt of late Paleozoic or Mesozoic age affected all pre-Tertiary rocks in the region; main thrust faults, not exposed in the map area, are interpreted to underlie the map area in an arcuate pattern, striking north, northeast, and east. The predominant vergence of thrust faults exposed elsewhere in the region, including the Belted Range and Specter Range thrusts, was to the east, southeast, and south. The vertical to overturned strata of the Striped Hills are hypothesized to result from successive stacking of three south-vergent thrust ramps, the lowest of which is the Specter Range thrust. The CP thrust is interpreted as a north-vergent backthrust that may have been roughly contemporaneous with the Belted Range and Specter Range thrusts. The southwest Nevada volcanic field consists predominantly of a series of silicic tuffs and lava flows ranging in age from 15 to 8 Ma. The map area is in the southwestern quadrant of the southwest Nevada volcanic field, just south of the Timber Mountain caldera complex. The Claim Canyon caldera, exposed in the northern part of the map area, contains thick deposits of the 12.7-Ma Tiva Canyon Tuff, along with widespread megabreccia deposits of similar age, and subordinate thick exposures of other 12.8- to 12.7-Ma Paintbrush Group rocks. An irregular, blocky fault array, which affects parts of the caldera and much of the nearby area, includes several large-displacement, steeply dipping faults that strike radially to the caldera and bound south-dipping blocks of volcanic rock. South and southeast of the Claim Canyon caldera, in the area that includes Yucca Mountain, the Neogene fault pattern is dominated by closely spaced, north-northwest- to north-northeast-striking normal faults that lie within a north-trending graben. This 20- to 25-km-wide graben includes Crater Flat, Yucca Mountain, and Fortymile Wash, and is bounded on the east by the 'gravity fault' and on the west by the Bare Mountain fault. Both of these faults separate Proterozoic and Paleozoic sedimentary rocks in their footwalls from Miocene volcanic rocks in their hanging walls. Stratigraphic and structural relations at Yucca Mountain demonstrate that block-bounding faults were active before and during eruption of the 12.8- to 12.7-Ma Paintbrush Group, and significant motion on these faults continued unt

Mineralogenic characteristics of osteogenic lineage-committed human dental pulp stem cells following their exposure to a discoloration-free calcium aluminosilicate cement.

PubMed

Niu, Li-Na; Pei, Dan-Dan; Morris, Matthew; Jiao, Kai; Huang, Xue-Qing; Primus, Carolyn M; Susin, Lisiane F; Bergeron, Brian E; Pashley, David H; Tay, Franklin R

2016-10-01

An experimental discoloration-free calcium aluminosilicate cement has been developed with the intention of maximizing the beneficial attributes of tricalcium silicate cements and calcium aluminate cements. The present study examined the effects of this experimental cement (Quick-Set2) on the mineralogenic characteristics of osteogenic lineage-committed human dental pulp stem cells (hDPSCs), by comparing the cellular responses with a commercially available tricalcium silicate cement (white mineral trioxide aggregate (ProRoot(®) MTA); WMTA). The osteogenic potential of hDPSCs exposed to the cements was examined using qRT-PCR for osteogenic gene expressions, Western blot for osteogenic-related protein expressions, alkaline phosphatase enzyme activity, Alizarin red S staining, Fourier transform infrared spectroscopy and transmission electron microscopy of extracellular calcium deposits. Results of the six assays indicated that osteogenic differentiation of hDPSCs was significantly enhanced after exposure to the tricalcium silicate cement or the experimental calcium aluminosilicate cement, with the former demonstrating better mineralogenic stimulation capacity. The better osteogenic stimulating effect of the tricalcium silicate cement on hDPSCs may be due to its relatively higher silicate content, or higher OH(-) and Ca(2+) release. Further investigations with the use of in vivo animal models are required to validate the potential augmenting osteogenic effects of the experimental discoloration-free calcium aluminosilicate cement. Published by Elsevier Ltd.

Titanite chronology, thermometry, and speedometry of ultrahigh-temperature (UHT) calc-silicates from south Madagascar: U-Pb dates, Zr temperatures, and lengthscales of trace-element diffusion

NASA Astrophysics Data System (ADS)

Holder, R. M.; Hacker, B. R.

2017-12-01

Calc-silicate rocks are often overlooked as sources of pressure-temperature-time data in granulite-UHT metamorphic terranes due to the strong dependence of calc-silicate mineral assemblages on complex fluid compositions and a lack of thermodynamic data on common high-temperature calc-silicate minerals such as scapolite. In the Ediacaran-Cambrian UHT rocks of southern Madagascar, clinopyroxene-scapolite-feldspar-quartz-zircon-titanite calc-silicate rocks are wide-spread. U-Pb dates of 540-520 Ma from unaltered portions of titanite correspond to cooling of the rocks through upper-amphibolite facies and indicate UHT metamorphism occurred before 540 Ma. Zr concentrations in these domains preserve growth temperatures of 900-950 °C, consistent with peak temperatures calculated by pseudosection modeling of nearby osumilite-bearing gneisses. Younger U-Pb dates (510-490 Ma) correspond to fluid-mediated Pb loss from titanite grains, which occurred below their diffusive Pb-closure temperature, along fractures. The extent of fluid alteration is seen clearly in back-scattered electron images and Zr-, Al-, Fe-, Ce-, and Nb-concentration maps. Laser-ablation depth profiling of idioblastic titanite grains shows preserved Pb diffusion profiles at grain rims, but there is no evidence for Zr diffusion, indicating that it was effectively immobile even at UHT.

Multiple generations of grain aggregation in different environments preceded solar system body formation.

PubMed

Ishii, Hope A; Bradley, John P; Bechtel, Hans A; Brownlee, Donald E; Bustillo, Karen C; Ciston, James; Cuzzi, Jeffrey N; Floss, Christine; Joswiak, David J

2018-06-26

The solar system formed from interstellar dust and gas in a molecular cloud. Astronomical observations show that typical interstellar dust consists of amorphous ( a -) silicate and organic carbon. Bona fide physical samples for laboratory studies would yield unprecedented insight about solar system formation, but they were largely destroyed. The most likely repositories of surviving presolar dust are the least altered extraterrestrial materials, interplanetary dust particles (IDPs) with probable cometary origins. Cometary IDPs contain abundant submicron a- silicate grains called GEMS (glass with embedded metal and sulfides), believed to be carbon-free. Some have detectable isotopically anomalous a- silicate components from other stars, proving they are preserved dust inherited from the interstellar medium. However, it is debated whether the majority of GEMS predate the solar system or formed in the solar nebula by condensation of high-temperature (>1,300 K) gas. Here, we map IDP compositions with single nanometer-scale resolution and find that GEMS contain organic carbon. Mapping reveals two generations of grain aggregation, the key process in growth from dust grains to planetesimals, mediated by carbon. GEMS grains, some with a- silicate subgrains mantled by organic carbon, comprise the earliest generation of aggregates. These aggregates (and other grains) are encapsulated in lower-density organic carbon matrix, indicating a second generation of aggregation. Since this organic carbon thermally decomposes above ∼450 K, GEMS cannot have accreted in the hot solar nebula, and formed, instead, in the cold presolar molecular cloud and/or outer protoplanetary disk. We suggest that GEMS are consistent with surviving interstellar dust, condensed in situ, and cycled through multiple molecular clouds. Copyright © 2018 the Author(s). Published by PNAS.

Trapping Planetary Noble Gases During the Fischer-Tropsch-Type Synthesis of Organic Materials

NASA Technical Reports Server (NTRS)

Nuth, Joseph A.; Johnson, N. M.; Meshik, A.

2010-01-01

When hydrogen, nitrogen and CO arc exposed to amorphous iron silicate surfaces at temperatures between 500 - 900K, a carbonaceous coating forms via Fischer-Tropsch type reactions!, Under normal circumstances such a catalytic coating would impede or stop further reaction. However, we find that this coating is a better catalyst than the amorphous iron silicates that initiate these rcactions:u . The formation of a self-perpetuating catalytic coating on grain surfaces could explain the rich deposits of macromolecular carbon found in primitive meteorites and would imply that protostellar nebulae should be rich in organic materiaL Many more experiments are needed to understand this chemical system and its application to protostellar nebulae.

The Mineralogy of Circumstellar Silicates Preserved in Cometary Dust

NASA Technical Reports Server (NTRS)

Keller, L. P.; Messenger, S.

2010-01-01

Interplanetary dust particles (IDPs) contain a record of the building blocks of the solar system including presolar grains, molecular cloud material, and materials formed in the early solar nebula. Cometary IDPs have remained relatively unaltered since their accretion because of the lack of parent body thermal and aqueous alteration. We are using coordinated transmission electron microscope (TEM) and ion microprobe studies to establish the origins of the various components within cometary IDPs. Of particular interest is the nature and abundance of presolar silicates in these particles because astronomical observations suggest that crystalline and amorphous silicates are the dominant grain types produced in young main sequence stars and evolved O-rich stars. Five circumstellar grains have been identified including three amorphous silicate grains and two polycrystalline aggregates. All of these grains are between 0.2 and 0.5 micrometers in size. The isotopic compositions of all five presolar silicate grains fall within the range of presolar oxides and silicates, having large (17)O-enrichments and normal (18)O/(16)O ratios (Group 1 grains from AGB and RG stars). The amorphous silicates are chemically heterogeneous and contain nanophase FeNi metal and FeS grains in a Mg-silicate matrix. Two of the amorphous silicate grains are aggregates with subgrains showing variable Mg/Si ratios in chemical maps. The polycrystalline grains show annealed textures (equilibrium grains boundaries, uniform Mg/Fe ratios), and consist of 50-100 nm enstatite and pyrrhotite grains with lesser forsterite. One of the polycrystalline aggregates contains a subgrain of diopside. The polycrystalline aggregates form by subsolidus annealing of amorphous precursors. The bulk compositions of the five grains span a wide range in Mg/Si ratios from 0.4 to 1.2 (avg. 0.86). The average Fe/Si (0.40) and S/Si (0.21) ratios show a much narrower range of values and are approximately 50% of their solar abundances. The latter observation may indicate a decoupling of the silicate and sulfide components in grains that condense in stellar outflows. The amorphous silicate grains described here were not extensively affected by irradiation, sputtering, or thermal processing and may represent relatively pristine circumstellar grains. They are strong candidates for the "dirty silicates" in astronomical observations of circumstellar dust shells. The polycrystalline grains were originally amorphous silicate grains that were likely annealed in the early solar nebula but the processing was not sufficient to erase their anomalous oxygen isotopic compositions.

Morpho-structural and ecological features of a shallow vermetid bioconstruction in the Tyrrhenian Sea (Mediterranean Sea, Italy)

NASA Astrophysics Data System (ADS)

Donnarumma, Luigia; Sandulli, Roberto; Appolloni, Luca; Di Stefano, Floriana; Russo, Giovanni Fulvio

2018-01-01

Biogenic formations, built up by the sessile and gregarious vermetid gastropod Dendropoma cristatum, were studied from June to October 2014 along the rocky shores of Licosa islet (Gulf of Salerno, Tyrrhenian Sea), where they build up the northernmost reefs in the Mediterranean Sea in order to shed light on possible latitudinal changes. The islet has two differently exposed sides, with three types of vermetid formations: the first consists in a thin layer composed by vermetid gastropods and the coralline alga N. brassica-florida, widespread only in the sheltered side of the islet; the second is represented by small isolated pillows (13.9 ± 5.64 cm), all around the islet at depth of more than fifteen centimetres; the third is a well-structured reef, characterized by a dense layer of mollusc shells that overgrow each other, only found in the exposed side of the islet. The vermetid reef was monitored in two sites with different substrates: ancient walls, made of calcareous lateritious material, and the flysch rocks, composed by siliceous turbiditic deposits. While no differences arise in gastropod density related to rock type (calcareous lateritious material versus siliceous turbiditic deposits), significant differences have been found along a vertical gradient, seeing density increases from the upper intertidal to the upper subtidal level. The associated algal cover seems to be inversely related to the vermetid density. In the upper intertidal, D. cristatum was almost completely covered (about 83%) by a thick layer of encrusting alga N. brassica-florida. In the lower intertidal the encrusting alga disappear but the shells of vermetid gastropods were remarkably colonized by the erected red algae of the "Laurencia complex" (70%) while in the upper subtidal, the vermetid shells were scarcely covered, mainly by other algal species (13%). By comparing present data with those of Sicilian reefs no evidences arise due to the different latitude. Innovative approaches (Remotely Piloted Aircraft Systems technology and fractal geometry) applied to these marine bioconstructions, resulted very effective in mapping and structuring the complexity of the reefs.

Volcanism on Io: Insights from Global Geologic Mapping

NASA Astrophysics Data System (ADS)

Williams, D. A.; Keszthelyi, L. P.; Crown, D. A.; Yff, J. A.; Jaeger, W. L.; Schenk, P. M.

2008-12-01

NASA's Galileo Mission (1996-2003) acquired excellent images of the antijovian (or far side) hemisphere of Jupiter's volcanic moon Io, which are complementary to the subjovian (or near side) images obtained by the 1979 NASA Voyager Mission. In 2005 the U.S. Geological Survey produced a set of global image mosaics of Io (spatial resolution 1 kilometer/picture element and full color) that enable for the first time production of a complete global geologic map. We have mapped Io using ArcGIS software to assess the types and abundances of process-related geologic material units and structures, to gain further insights into the types and styles of activity that shape this hyperactive volcanic moon. We find that lava flow fields make up about 28% of the surface, in which bright (presumably sulfur) flows are twice as abundant as dark (presumably silicate) flows. Many of the bright flows do not have adjacent dark flows, perhaps indicative of extensive primary rather than secondary sulfur volcanism (i.e., effusion of crustal sulfur magma, rather than sulfur-rich country rock melted by adjacent silicate magma). Ephemeral, diffuse pyroclastic plume deposits mantle about 18% of the surface at any time, and include condensed sulfur and sulfur dioxide gases and silicate ash. Patera (i.e., caldera) floors contain lava flows and/or some lava lakes, and cover only 2.5% of the surface, but are the source of most of the active hot spots. Restriction of effusive resurfacing mostly to caldera-like topographic depressions, and the ephemeral nature of plume deposits, explains the relatively small amount of surface changes observed between the Voyager and Galileo missions. Tectonic mountains, rising up to 17 km, cover about 3% of the surface, but close association of about one-third to one-half of the mountains with paterae suggest linkage of volcanic and tectonic processes. About 67% of Io is covered by plains, thought to consist of silicate crust covered with accumulations of lava flows and pyroclastics whose boundaries are not discernable. No impact craters have been found on Io, indicating a surface age of less than a few tens of millions of years. We will discuss the implications of these results for Io's volcanism.

Analysis of multispectral and hyperspectral longwave infrared (LWIR) data for geologic mapping

NASA Astrophysics Data System (ADS)

Kruse, Fred A.; McDowell, Meryl

2015-05-01

Multispectral MODIS/ASTER Airborne Simulator (MASTER) data and Hyperspectral Thermal Emission Spectrometer (HyTES) data covering the 8 - 12 μm spectral range (longwave infrared or LWIR) were analyzed for an area near Mountain Pass, California. Decorrelation stretched images were initially used to highlight spectral differences between geologic materials. Both datasets were atmospherically corrected using the ISAC method, and the Normalized Emissivity approach was used to separate temperature and emissivity. The MASTER data had 10 LWIR spectral bands and approximately 35-meter spatial resolution and covered a larger area than the HyTES data, which were collected with 256 narrow (approximately 17nm-wide) spectral bands at approximately 2.3-meter spatial resolution. Spectra for key spatially-coherent, spectrally-determined geologic units for overlap areas were overlain and visually compared to determine similarities and differences. Endmember spectra were extracted from both datasets using n-dimensional scatterplotting and compared to emissivity spectral libraries for identification. Endmember distributions and abundances were then mapped using Mixture-Tuned Matched Filtering (MTMF), a partial unmixing approach. Multispectral results demonstrate separation of silica-rich vs non-silicate materials, with distinct mapping of carbonate areas and general correspondence to the regional geology. Hyperspectral results illustrate refined mapping of silicates with distinction between similar units based on the position, character, and shape of high resolution emission minima near 9 μm. Calcite and dolomite were separated, identified, and mapped using HyTES based on a shift of the main carbonate emissivity minimum from approximately 11.3 to 11.2 μm respectively. Both datasets demonstrate the utility of LWIR spectral remote sensing for geologic mapping.

Properties of zirconium silicate and zirconium-silicon oxynitride high-k dielectric alloys for advanced microelectronic applications: Chemical and electrical characterizations

NASA Astrophysics Data System (ADS)

Ju, Byongsun

2005-11-01

As the microelectronic devices are aggressively scaled down to the 1999 International Technology Roadmap, the advanced complementary metal oxide semiconductor (CMOS) is required to increase packing density of ultra-large scale integrated circuits (ULSI). High-k alternative dielectrics can provide the required levels of EOT for device scaling at larger physical thickness, thereby providing a materials pathway for reducing the tunneling current. Zr silicates and its end members (SiO2 and ZrO2) and Zr-Si oxynitride films, (ZrO2)x(Si3N 4)y(SiO2)z, have been deposited using a remote plasma-enhanced chemical vapor deposition (RPECVD) system. After deposition of Zr silicate, the films were exposed to He/N2 plasma to incorporate nitrogen atoms into the surface of films. The amount of incorporated nitrogen atoms was measured by on-line Auger electron spectrometry (AES) as a function of silicate composition and showed its local minimum around the 30% silicate. The effect of nitrogen atoms on capacitance-voltage (C-V) and leakage-voltage (J-V) were also investigated by fabricating metal-oxide-semiconductor (MOS) capacitors. Results suggested that incorporating nitrogen into silicate decreased the leakage current in SiO2-rich silicate, whereas the leakage increased in the middle range of silicate. Zr-Si oxynitride was a pseudo-ternary alloy and no phase separation was detected by x-ray photoelectron spectroscopy (XPS) analysis up to 1100°C annealing. The leakage current of Zr-Si oxynitride films showed two different temperature dependent activation energies, 0.02 eV for low temperature and 0.3 eV for high temperature. Poole-Frenkel emission was the dominant leakage mechanism. Zr silicate alloys with no Si3N4 phase were chemically separated into the SiO2 and ZrO2 phase as annealed above 900°C. While chemical phase separation in Zr silicate films with Si 3N4 phase (Zr-Si oxynitride) were suppressed as increasing the amount of Si3N4 phase due to the narrow bonding network m Si3N4 phase. (3.4 bonds/atom for Si3 N4 network, 2.67 bonds/atom for SiO2 network).

Polymeric microcapsules with switchable mechanical properties for self-healing concrete: synthesis, characterisation and proof of concept

NASA Astrophysics Data System (ADS)

Kanellopoulos, A.; Giannaros, P.; Palmer, D.; Kerr, A.; Al-Tabbaa, A.

2017-04-01

Microcapsules, with sodium silicate solution as core, were produced using complex coacervation in a double, oil-in-water-in oil, emulsion system. The shell material was a gelatin-acacia gum crosslinked coacervate and the produced microcapsules had diameters ranging from 300 to 700 μm. The shell material designed with switchable mechanical properties. When it is hydrated exhibits soft and ‘rubbery’ behaviour and, when dried, transitions to a stiff and ‘glassy’ material. The microcapsules survived drying and rehydrating cycles and preserved their structural integrity when exposed to highly alkaline solutions that mimic the pH environment of concrete. Microscopy revealed that the shell thickness of the microcapsules varies across their perimeter from 5 to 20 μm. Thermal analysis showed that the produced microcapsules were very stable up to 190 °C. Proof of concept investigation has demonstrated that the microcapsules successfully survive and function when exposed to a cement-based matrix. Observations showed that the microcapsules survive mixing with cement and rupture successfully upon crack formation releasing the encapsulated sodium silicate solution.

Development of inverted metamorphic isograds in the western metamorphic belt, Juneau, Alaska

USGS Publications Warehouse

Himmelberg, G.R.; Brew, D.A.; Ford, A.B.

1991-01-01

An inverted metamorphic gradient is preserved in the western metamorphic belt near Juneau, Alaska. Detailed mapping of pelitic single-mineral isograds, systematic changes in mineral assemblages, and silicate geothermometry indicate that thermal peak metamorphic conditions increase structurally upward over a distance of about 8 km. Silicate geobarometry suggests that the thermal peak metamorphism occurred under pressures of 9-11 kbar. Our preferred interpretation of the cause of the inverted gradient is that it formed during compression of a thickened wedge of relatively wet and cool rocks in response to heat flow associated with the formation and emplacement of tonalite sill magma. -from Authors

Geophysical methods as mapping tools in a strata-bound gold deposit: Haile mine, South Carolina slate belt.

USGS Publications Warehouse

Wynn, J.C.; Luce, R.W.

1984-01-01

The Haile mine is the largest gold producer in the eastern USA. It is postulated to be a strata-bound gold deposit formed by a fumarolic or hot-spring system in felsic tuffs of Cambrian(?) age. Two mineralized zones occur, each composed of a sericitic part overlain by a siliceous part. Au is concentrated in especially silicified horizons and in pyrite horizons in the siliceous part of each mineralized zone. The tuffs are metamorphosed to greenschist facies and intruded by diabase and other mafic dykes. Weathering is deep and the mineralized tuffs are partly covered by coastal-plain sediments. It is suggested that certain geophysical methods may be useful in mapping and exploring Haile-type deposits in the Carolina slate belt. Very low frequency electromagnetic resistivity surveys help define alteration and silicified zones. A magnetic survey found sharp highs that correlate with unexposed mafic and ultramafic dykes. Induced polarization proved useful in giving a two-dimensional view of the structure.-G.J.N.

Biocompatibility and bioactivity of calcium silicate-based endodontic sealers in human dental pulp cells.

PubMed

Mestieri, Leticia Boldrin; Gomes-Cornélio, Ana Lívia; Rodrigues, Elisandra Márcia; Salles, Loise Pedrosa; Bosso-Martelo, Roberta; Guerreiro-Tanomaru, Juliane Maria; Tanomaru-Filho, Mário

2015-10-01

Mineral Trioxide Aggregate (MTA) is a calcium silicate-based material. New sealers have been developed based on calcium silicate as MTA Fillapex and MTA Plus. The aim of this study was to evaluate biocompatibility and bioactivity of these two calcium silicate-based sealers in culture of human dental pulp cells (hDPCs). The cells were isolated from third molars extracted from a 16-year-old patient. Pulp tissue was sectioned into fragments with approximately 1 mm3 and kept in supplemented medium to obtain hDPCs adherent cultures. Cell characterization assays were performed to prove the osteogenic potential. The evaluated materials were: MTA Plus (MTAP); MTA Fillapex (MTAF) and FillCanal (FC). Biocompatibility was evaluated with MTT and Neutral Red (NR) assays, after hDPCs exposure for 24 h to different dilutions of each sealer extract (1:2, 1:3 and 1:4). Unexposed cells were the positive control (CT). Bioactivity was assessed by alkaline phosphatase (ALP) enzymatic assay in cells exposed for one and three days to sealer extracts (1:4 dilution). All data were analyzed by ANOVA and Tukey post-test (p≤0.05%). MTT and NR results showed suitable cell viability rates for MTAP at all dilutions (90-135%). Cells exposed to MTAF and FC (1:2 and 1:4 dilutions) showed significant low viability rate when compared to CT in MTT. The NR results demonstrated cell viability for all materials tested. In MTAP group, the cells ALP activity was similar to CT in one and three days of exposure to the material. MTAF and FC groups demonstrated a decrease in ALP activity when compared to CT at both periods of cell exposure. The hDPCs were suitable for the evaluation of new endodontic materialsin vitro. MTAP may be considered a promising material for endodontic treatments.

Characterization of waste rock associated with acid drainage at the Penn Mine, California, by ground-based visible to short-wave infrared reflectance spectroscopy assisted by digital mapping

USGS Publications Warehouse

Montero, S.I.C.; Brimhall, G.H.; Alpers, Charles N.; Swayze, G.A.

2005-01-01

Prior to remediation at the abandoned Cu-Zn Penn Mine in the Foothills massive sulfide belt of the Sierra Nevada, CA, acid mine drainage (AMD) was created, in part, by the subaerial oxidation of sulfides exposed on several waste piles. To support remediation efforts, a mineralogical study of the waste piles was undertaken by acquiring reflectance spectra (measured in the visible to short-wave infrared range of light (0.35-2.5 ??m) using a portable, digitally integrated pen tablet PC mapping system with differential global positioning system and laser rangefinder support. Analysis of the spectral data made use of a continuum removal and band-shape comparison method, and of reference spectral libraries of end-member minerals and mineral mixtures. Identification of secondary Fe-bearing minerals focused on band matching in the region between 0.43 and 1.3 ??m. Identification of sheet and other silicates was based on band-shape analysis in the region between 1.9 and 2.4 ??m. Analysis of reflectance spectra of characterized rock samples from the mine helped in gauging the spectral response to particle size and mixtures. The resulting mineral maps delineated a pattern of accumulation of secondary Fe minerals, wherein centers of copiapite and jarosite that formed at low pH (<3) were surrounded successively by goethite and hematite, which mark progressive increases in pH. This pattern represents the evolution of acid solutions discharged from the pyritic waste piles and the subsequent accumulation of secondary precipitates by hydrolysis reactions. The results highlight the high capacity of the pyritic waste to release further acid mine drainage into the environment, as well as the effectiveness of the mapping method to detect subtle changes in surface mineralogy and to produce maps useful to agencies responsible for remediating the site. ?? 2004 Elsevier B.V. All rights reserved.

Bonding by Hydroxide-Catalyzed Hydration and Dehydration

NASA Technical Reports Server (NTRS)

Gwo, Dz-Hung

2008-01-01

A simple, inexpensive method for bonding solid objects exploits hydroxide-catalyzed hydration and dehydration to form silicate-like networks in thin surface and interfacial layers between the objects. The method can be practiced at room temperature or over a wide range of temperatures. The method was developed especially to enable the formation of precise, reliable bonds between precise optical components. The bonds thus formed exhibit the precision and transparency of bonds formed by the conventional optical-contact method and the strength and reliability of high-temperature frit bonds. The method also lends itself to numerous non-optical applications in which there are requirements for precise bonds and/or requirements for bonds, whether precise or imprecise, that can reliably withstand severe environmental conditions. Categories of such non-optical applications include forming composite materials, coating substrates, forming laminate structures, and preparing objects of defined geometry and composition. The method is applicable to materials that either (1) can form silicate-like networks in the sense that they have silicate-like molecular structures that are extensible into silicate-like networks or (2) can be chemically linked to silicate-like networks by means of hydroxide-catalyzed hydration and dehydration. When hydrated, a material of either type features surface hydroxyl (-OH) groups. In this method, a silicate-like network that bonds two substrates can be formed either by a bonding material alone or by the bonding material together with material from either or both of the substrates. Typically, an aqueous hydroxide bonding solution is dispensed and allowed to flow between the mating surfaces by capillary action. If the surface figures of the substrates do not match precisely, bonding could be improved by including a filling material in the bonding solution. Preferably, the filling material should include at least one ingredient that can be hydrated to have exposed hydroxyl groups and that can be chemically linked, by hydroxide catalysis, to a silicate-like network. The silicate-like network could be generated in situ from the filling material and/or substrate material, or could be originally present in the bonding material.

Production of Organic Grain Coatings by Surface-Mediated Reactions and the Consequences of This Process for Meteoritic Constituents

NASA Technical Reports Server (NTRS)

Nuth, Joseph A., III; Johnson, Natasha M.

2011-01-01

When hydrogen, nitrogen and CO are exposed to amorphous iron silicate surfaces at temperatures between 500 - 900K, a carbonaceous coating forms via Fischer-Tropsch type reactions. Under normal circumstances such a catalytic coating would impede or stop further reaction. However, we find that this coating is a better catalyst than the amorphous iron silicates that initiate these reactions. The formation of a self-perpetuating catalytic coating on grain surfaces could explain the rich deposits of macromolecular carbon found in primitive meteorites and would imply that protostellar nebulae should be rich in organic material. Many more experiments are needed to understand this chemical system and its application to protostellar nebulae.

The hydrophilic-to-hydrophobic transition in glassy silica is driven by the atomic topology of its surface

NASA Astrophysics Data System (ADS)

Yu, Yingtian; Krishnan, N. M. Anoop; Smedskjaer, Morten M.; Sant, Gaurav; Bauchy, Mathieu

2018-02-01

The surface reactivity and hydrophilicity of silicate materials are key properties for various industrial applications. However, the structural origin of their affinity for water remains unclear. Here, based on reactive molecular dynamics simulations of a series of artificial glassy silica surfaces annealed at various temperatures and subsequently exposed to water, we show that silica exhibits a hydrophilic-to-hydrophobic transition driven by its silanol surface density. By applying topological constraint theory, we show that the surface reactivity and hydrophilic/hydrophobic character of silica are controlled by the atomic topology of its surface. This suggests that novel silicate materials with tailored reactivity and hydrophilicity could be developed through the topological nanoengineering of their surface.

Validation of Innovative Exploration Technologies for Newberry Volcano: Drill Site Location Map 2010

DOE Data Explorer

Jaffe, Todd

2012-01-01

Newberry seeks to explore "blind" (no surface evidence) convective hydrothermal systems associated with a young silicic pluton on the flanks of Newberry Volcano. This project will employ a combination of innovative and conventional techniques to identify the location of subsurface geothermal fluids associated with the hot pluton. Newberry project drill site location map 2010. Once the exploration mythology is validated, it can be applied throughout the Cascade Range and elsewhere to locate and develop “blind” geothermal resources.

Carbonate-silicate liquid immiscibility upon impact melting, Ries Crater, Germany

NASA Astrophysics Data System (ADS)

Graup, Guenther

1999-05-01

The 24-km-diameter Ries impact crater in southern Germany is one of the most studied impact structures on Earth. The Ries impactor struck a Triassic to Upper Jurassic sedimentary sequence overlying Hercynian crystalline basement. At the time of impact (14.87 +/- 0.36 Ma; Storzer et al., 1995), the 350 m thick Malm limestone was present only to the S and E of the impact site. To the N and W, the Malm had been eroded away, exposing the underlying Dogger and Lias. The largest proportion of shocked target material is in the impact melt-bearing breccia suevite. The suevite had been believed to be derived entirely from the crystalline basement. Calcite in the suevite has been interpreted as a post-impact hydrothermal deposit. From optical inspection of 540 thin sections of suevite from 32 sites, I find that calcite in the suevite shows textural evidence of liquid immiscibility with the silicate impact melt. Textural evidence of liquid immiscibility between silicate and carbonate melt in the Ries suevite includes: carbonate globules within silicate glass, silicate globules embedded in carbonate, deformable and coalescing carbonate spheres within silicate glass, sharp menisci or cusps and budding between silicate and carbonate melt, fluidal textures and gas vesicles in carbonate schlieren, a quench crystallization sequence of the carbonate, spinifex textured quenched carbonate, separate carbonate spherules in the suevite mineral-fragment-matrix, and inclusions of mineral fragments suspended in carbonate blebs. Given this evidence of liquid immiscibility, the carbonate in the suevite has, therefore, like the silicate melt a primary origin by impact shock melting. Evidence of carbonate-silicate liquid immiscibility is abundant in the suevites to the SW to E of the Ries crater. The rarer suevites to the W to NE of the crater are nearly devoid of carbonate melts. This correspondence between the occurrence of outcropping limestones at the target surface and the formation of carbonate melt, indicates that the Malm limestones are the source rocks of the carbonate impact melt. This correspondence shows that the suevites preserve a compositional memory of their source rocks. From the regional distribution of suevites with or without immiscible carbonate melts, it is inferred that the Ries impactor hit the steep Albtrauf escarpment at its toe, in an oblique impact from the north.

Field and Experimental Constraints on the Dynamics of Replenished Silicic Magma Chambers

NASA Astrophysics Data System (ADS)

Bain, A. A.; Jellinek, M.

2008-12-01

The underlying causes of catastrophic caldera-forming volcanic eruptions remain poorly understood. However, the occurrence of magma mixing within bimodal systems has become increasingly linked with such eruptions. In particular, buoyancy effects related to unstable density contrasts arising as a result of silicic- basaltic magma interactions may play an important role in the growth, differentiation and catastrophic eruption of silicic magma chambers. Evidence of such magmatic interactions can be found in layered intrusions from the Coastal Maine Magmatic Province (USA), where well-exposed cross-sections reveal hundreds of laterally-extensive basaltic sheets, apparently injected as intrusive lava flows onto the growing floors of silicic magma chambers. Interfaces between mafic and silicic layers are commonly sharply defined and exhibit deformation parallel to the inferred direction of palaeo-gravity. Our field observations suggest that the cooling, settling and buckling of gravitationally-unstable mafic replenishments may have driven large-scale (basalt layer depth) and small- scale (crystal diameter) upwelling and/or overturning of underlying buoyant silicic cumulate material. In order to characterize the full range of buoyancy effects, we carried out extensive spectral analysis of high- resolution digital field measurements from the Pleasant Bay and Mount Desert Island intrusions. In many cases, Rayleigh-Taylor theory and the longest measured wavelength of deformation indicate that a large and potentially-quantifiable fraction of the original, pre-replenishment silicic cumulate thickness may be missing, implying that vertical mass transfer has occurred. In addition, the shortest wavelengths of deformation are generally consistent with observed length-scales of crystals and clumps of crystals at these localities. With the aim of understanding the initial conditions that gave rise to these field observations, we conduct a series of laboratory experiments in which we observe the development of a Rayleigh-Taylor instability between a buoyant basal fluid layer overlain by a denser fluid layer. In order to identify the important parameters in the problem, we perform these experiments for a wide range of density contrasts, layer thicknesses and fluid rheologies (i.e. we vary particle concentration from the dilute to highly-crystalline limits to simulate freezing basalt and re-heated silicic cumulate rheologies). Regimes in which the entire silicic layer becomes unstable are potentially responsible for overturning the system and iniating large volcanic eruptions.

Bismuth silicate glass containing heavy metal oxide as a promising radiation shielding material

NASA Astrophysics Data System (ADS)

Elalaily, Nagia A.; Abou-Hussien, Eman M.; Saad, Ebtisam A.

2016-12-01

Optical and FTIR spectroscopic measurements and electron paramagnetic resonance (EPR) properties have been utilized to investigate and characterize the given compositions of binary bismuth silicate glasses. In this work, it is aimed to study the possibility of using the prepared bismuth silicate glasses as a good shielding material for γ-rays in which adding bismuth oxide to silicate glasses causes distinguish increase in its density by an order of magnitude ranging from one to two more than mono divalent oxides. The good thermal stability and high density of the bismuth-based silicate glass encourage many studies to be undertaken to understand its radiation shielding efficiency. For this purpose a glass containing 20% bismuth oxide and 80% SiO2 was prepared using the melting-annealing technique. In addition the effects of adding some alkali heavy metal oxides to this glass, such as PbO, BaO or SrO, were also studied. EPR measurements show that the prepared glasses have good stability when exposed to γ-irradiation. The changes in the FTIR spectra due to the presence of metal oxides were referred to the different housing positions and physical properties of the respective divalent Sr2+, Ba2+ and Pb2+ ions. Calculations of optical band gap energies were presented for some selected glasses from the UV data to support the probability of using these glasses as a gamma radiation shielding material. The results showed stability of both optical and magnetic spectra of the studied glasses toward gamma irradiation, which validates their irradiation shielding behavior and suitability as the radiation shielding candidate materials.

CaCl 2 -Accelerated Hydration of Tricalcium Silicate: A STXM Study Combined with 29 Si MAS NMR

DOE PAGES

Li, Qinfei; Ge, Yong; Geng, Guoqing; ...

2015-01-01

Tmore » he effect of calcium chloride (CaCl 2 ) on tricalcium silicate (C 3 S) hydration was investigated by scanning transmission X-ray microscopy (SXM) with Near Edge X-ray Absorption Fine Structure (NEXAFS) spectra and 29 Si MAS NMR. SXM is demonstrated to be a powerful tool for studying the chemical composition of a cement-based hydration system. he Ca L 3,2 -edge NEXAFS spectra obtained by examining C 3 S hydration in the presence of CaCl 2 showed that this accelerator does not change the coordination of calcium in the calcium silicate hydrate (C-S-H), which is the primary hydration product. O K-edge NEXAFS is also very useful in distinguishing the chemical components in hydrated C 3 S. Based on the Ca L 3,2 -edge spectra and chemical component mapping, we concluded that CaCl 2 prefers to coexist with unhydrated C 3 S instead of C-S-H. In Si K-edge NEXAFS analysis, CaCl 2 increases the degree of silicate polymerization of C-S-H in agreement with the 29 Si CP/MAS NMR results, which show that the presence of CaCl 2 in hydrated C 3 S considerably accelerates the formation of middle groups ( Q 2 ) and branch sites ( Q 3 ) in the silicate chains of C-S-H gel at 1-day hydration.« less

Mapping Intraplate Volcanic Fields: A Case Study from Harrat Rahat, Saudi Arabia

NASA Astrophysics Data System (ADS)

Downs, D. T.; Stelten, M. E.; Champion, D. E.; Dietterich, H. R.

2017-12-01

Continental intraplate mafic volcanoes are typically small-volume (<1 km3), but are one of the most prevalent volcanic landforms on Earth, particularly in the >200 volcanic fields proposed to be active worldwide during the Holocene. Their small individual eruption volumes make any hazards low, however their high prevalence offsets this by raising the risk to populations and infrastructure. The western Arabian Plate hosts at least 15 continental, intra-plate volcanic fields that stretch >3,000 km south to north from Yemen to Turkey. In total, these volcanic fields comprise one of the largest alkali basalt volcanic provinces on Earth, covering an area of 180,000 km2. With a total volume of 20,000 km3, Harrat Rahat in western Saudi Arabia is one of the largest of these volcanic fields. Our study focused on mapping the northern third of the Harrat Rahat volcanic field using a multidisciplinary approach. We have discriminated >200 individual eruptive units, mainly basaltic lava flows throughout Harrat Rahat that are distinguished through a combination of field observations, petrography, geochemistry, paleomagnetism, and 40Ar/39Ar radiometric and 36Cl cosmogenic surface-exposure dating. We have compiled these results into a high-resolution geologic map, which provides new information about the timing, compositions, and eruptive processes of Quaternary volcanism in Harrat Rahat. For example, prior mapping and geochronology undertaken during the 1980s suggested that the majority of mafic and silicic volcanics erupted during the Miocene and Pliocene, whereas several of the youngest-appearing lava flows were interpreted to be Neolithic ( 7,000 to 4,500 years BP) to post-Neolithic. New mapping and age-constrained stratigraphic relations indicate that all exposed volcanic units within the northern third of Harrat Rahat erupted during the Pleistocene, with the exception of a single Holocene eruption in 1256 AD. This new multidisciplinary mapping is critical for understanding the overall spatial, temporal, and compositional evolution of Harrat Rahat, timescales of magmatic processes in the mantle and crust, and understanding hazards and risks associated with the varied styles of volcanism in the region.

Experimental Study of Porosity Changes in Shale Caprocks Exposed to Carbon Dioxide-Saturated Brine II: Insights from Aqueous Geochemistry

DOE PAGES

Miller, Quin R. S.; Wang, Xiuyu; Kaszuba, John P.; ...

2016-07-18

Laboratory experiments evaluated two shale caprock formations, the Gothic Shale and Marine Tuscaloosa Formation, at conditions relevant to carbon dioxide (CO 2) sequestration. Both rocks were exposed to CO 2-saturated brines at 160°C and 15 MPa for ~45 days. Baseline experiments for both rocks were pressurized with argon to 15 MPa for ~35 days. Varying concentrations of iron, aqueous silica, sulfate, and initial pH decreases coincide with enhanced carbonate and silicate dissolution due to reaction between CO 2-saturated brine and shale. Saturation indices were calculated and activity diagrams were constructed to gain insights into sulfate, silicate, and carbonate mineral stabilities.more » We found that upon exposure to CO 2-saturated brines, the Marine Tuscaloosa Formation appeared to be more reactive than the Gothic Shale. Evolution of aqueous geochemistry in the experiments is consistent with mineral precipitation and dissolution reactions that affect porosity. Finally, this study highlights the importance of tracking fluid chemistry to clarify downhole physicochemical responses to CO 2 injection and subsequent changes in sealing capacity in CO 2 storage and utilization projects.« less

Mesosiderites on Vesta: A Hyperspectral VIS-NIR Investigation

NASA Technical Reports Server (NTRS)

Palomba, E.; Longobardo, A.; DeSanctis, M. C.; Mittlefehldt, D. W.; Ammannito, E.; Capaccioni, F.; Capria, M. T.; Frigeri, A.; Tosi, F.; Zambon, F.;

The chemistry of Saudi Arabian sand: A deposition problem on helicopter turbine airfoils

NASA Technical Reports Server (NTRS)

Smialek, James L.

1991-01-01

Recent operations in the Persian Gulf have exposed military helicopter turbines to excessive amounts of ingested sand. Fine particles, less than 10 microns, are able to bypass the particle separators and enter the cooling and combustion systems. The initial sand chemistry varies by location, but is made up of a calcium aluminum silicate glass, SiO2 low quartz (Ca,Mg) CO3 dolomite, CaCO3 calcite, and occasionally CaCl rocksalt. The sand reacts in the hot combustion gases and deposits onto the turbine vanes as CaSO4, glass, and various crystalline silicates. Deposits up to 0.25 in. thick have been collected. Although cooling hole plugging is a considerable problem, excessive corrosion is not commonly observed due to the high melting point of GaSO4.

The chemistry of Saudi Arabian sand - A deposition problem on helicopter turbine airfoils

NASA Astrophysics Data System (ADS)

Smialek, James L.; Archer, Frances A.; Garlick, Ralph G.

Operations in the Persian Gulf have exposed military helicopter turbines to excessive amounts of ingested sand. Fine particles, less than 10 microns, are able to bypass the particle separators and enter the cooling and combustion systems. The initial sand chemistry varies by location, but is made up of a calcium aluminum silicate glass, SiO2 low quartz, (Ca,Mg)CO3 dolomite, CaCO3 calcite, and occasionally NaCl rocksalt. The sand reacts in the hot combustion gases and deposits onto the turbine vanes as CaSO4, glass, and various crystalline silicates. Deposits up to 5 mm thick have been collected. Although cooling hole plugging is a considerable problem, excessive corrosion is not commonly observed due to the high melting point of CaSO4.

The Chemistry of Saudi Arabian Sand - A Deposition Problem on Helicopter Turbine Airfoils

NASA Technical Reports Server (NTRS)

Smialek, James L.; Archer, Frances A.; Garlick, Ralph G.

1992-01-01

Operations in the Persian Gulf have exposed military helicopter turbines to excessive amounts of ingested sand. Fine particles, less than 10 microns, are able to bypass the particle separators and enter the cooling and combustion systems. The initial sand chemistry varies by location, but is made up of a calcium aluminum silicate glass, SiO2 low quartz, (Ca,Mg)CO3 dolomite, CaCO3 calcite, and occasionally NaCl rocksalt. The sand reacts in the hot combustion gases and deposits onto the turbine vanes as CaSO4, glass, and various crystalline silicates. Deposits up to 5 mm thick have been collected. Although cooling hole plugging is a considerable problem, excessive corrosion is not commonly observed due to the high melting point of CaSO4.

Insights into the martian hydrosphere from the nakhlites

NASA Astrophysics Data System (ADS)

Tomkinson, T.; Mark, D. F.; Lee, M.; Lindgren, P.; Stuart, F.

2011-12-01

The nakhlite meteorites contain minerals including clays, salts and carbonates that crystallized from water within an impact-induced hydrothermal system or subsurface aquifer [1,2]. These minerals can be used to explore the longevity, scale and evolution of the aqueous system. However, such work has proven to be challenging owing to their very fine crystal size and their compositional complexity. In this study we have used a suite of techniques including CT tomography, scanning and transmission electron microscopy and Ar/Ar dating to explore the history of secondary mineralization in the nakhlites. In total there are thirteen nakhlites, however, this study has focused on Nakhla as it is the only fall. To further understand their alteration relationships we also plan to study Lafayette, MIL 003346, Yamato 000593, 000749 and NWA 5790. In contrast to previous studies that have used polished thin sections, we have examined secondary minerals exposed on freshly produced fracture surfaces from the interior of the Nakhla meteorite. This technique has revealed six textures that have not previously been described. (1) Areas of nanocrystalline/amorphous growth of sheeted silicates appearing to nucleate from underlying Cl and C rich fibrous material. (2) Underlying material which forms on the olivine grains surface with a nanoscale fibrous structure contains intergrown <5 μm sized euhedral calcium sulphate crystals. (3) The overlying sheeted silicates are also cross-cut by veins of this Cl and C enriched fibrous material. (4) A concentrically Si, Cl, Ca, Mn and Fe zoned region of alteration with a diameter of ~90 μm that has also been observed potentially sourcing enrichments from an underlying halite grain and augite and magnetite inclusions formed from symplectic exsolution in the host olivine [3]. Additionally, we have observed (5) radial growth structures emanating from halite grains and (6) etch pits in the surfaces of olivines. We will also present preliminary Ar/Ar ages for the K-bearing alteration material within the nakhlites. The textures that we have observed suggest that the sheeted silicate material formed either during fluctuations in fluid compositions or as a result of these newly discovered sites of nucleation growth from the underlying Cl and C enriched fibrous material. The presence of the fibrous material cross-cutting the silicate could indicate the following: a subsequent injection of a saline fluid, an expansion of the fibrous material rupturing the silicate, or the remobilisation of the fibrous material. The sharp contacts of the silicate with these cross cutting veins of fibrous material suggest that this material (likely brine) was exposed to only very low temperatures [4] thus not remobilising and equilibrating with the surrounding material. Some of the features that we have found would have been lost in conventional thin section manufacture and may explain why they have not been observed previously.

Appalachian piedmont regolith: Relations of saprolite and residual soils to rock-type

USGS Publications Warehouse

Pavich, M.J.

1996-01-01

Saprolite is a major product of rock weathering on the Appalachian Piedmont from New Jersey to Alabama. On the Piedmont, it is the primary substrate from which residual soils are developed. Properties of saprolite and residual soils are highly related to their parent rocks. Studies of cores and outcrops illustrate that rock structure and mineralogy control upland regolith zonation. Saprolite develops by in situ chemical alteration of a wide variety of mafic to highly silicic rocks. Thickness of upland saprolite varies from a few meters on mafic rocks to tens of meters on silicic rocks. Saprolite thickness decreases with increasing slope and saprolite is generally thin or absent in valley bottoms. Massive residual subsoils and soils develop by physical and chemical processes that alter the upper few meters of saprolite. The fabric, texture and mineralogy of residual soils are distinctly different from underlying saprolite. The boundary between soil and saprolite is often gradual, and often a zone of low permeability. Geologic maps are useful guides to Piedmont regolith thickness and zonation. In regional design studies, geologic maps and regolith characteristics can be useful in environmental decision-making.

Mapping the distribution of vesicular textures on silicic lavas using the Thermal Infrared Multispectral Scanner

NASA Technical Reports Server (NTRS)

Ondrusek, Jaime; Christensen, Philip R.; Fink, Jonathan H.

1993-01-01

To investigate the effect of vesicularity on TIMS (Thermal Infrared Multispectral Scanner) imagery independent of chemical variations, we studied a large rhyolitic flow of uniform composition but textural heterogeneity. The imagery was recalibrated so that the digital number values for a lake in the scene matched a calculated ideal spectrum for water. TIMS spectra for the lava show useful differences in coarsely and finely vesicular pumice data, particularly in TIMS bands 3 and 4. Images generated by ratioing these bands accurately map out those areas known from field studies to be coarsely vesicular pumice. These texture-related emissivity variations are probably due to the larger vesicles being relatively deeper and separated by smaller septa leaving less smooth glass available to give the characteristic emission of the lava. In studies of inaccessible lava flows (as on Mars) areas of coarsely vesicular pumice must be identified and avoided before chemical variations can be interpreted. Remotely determined distributions of vesicular and glassy textures can also be related to the volatile contents and potential hazards associated with the emplacement of silicic lava flows on Earth.

Geologic Mapping and Mineral Resource Assessment of the Healy and Talkeetna Mountains Quadrangles, Alaska Using Minimal Cloud- and Snow-Cover ASTER Data

USGS Publications Warehouse

Hubbard, Bernard E.; Rowan1, Lawrence C.; Dusel-Bacon, Cynthia; Eppinger, Robert G.

2007-01-01

On July 8, 2003, ASTER acquired satellite imagery of a 60 km-wide swath of parts of two 1:250,000 Alaska quadrangles, under favorable conditions of minimal cloud- and snow-cover. Rocks from eight different lithotectonic terranes are exposed within the swath of data, several of which define permissive tracts for various mineral deposit types such as: volcanic-hosted massive sulfides (VMS) and porphyry copper and molybdenum. Representative rock samples collected from 13 different lithologic units from the Bonnifield mining district within the Yukon-Tanana terrane (YTT), plus hydrothermally altered VMS material from the Red Mountain prospect, were analyzed to produce a spectral library spanning the VNIR-SWIR (0.4 - 2.5 ?m) through the TIR (8.1 - 11.7 ?m). Comparison of the five-band ASTER TIR emissivity and decorrelation stretch data to available geologic maps indicates that rocks from the YTT display the greatest range and diversity of silica composition of the mapped terranes, ranging from mafic rocks to silicic quartzites. The nine-band ASTER VNIR-SWIR reflectance data and spectral matched-filter processing were used to map several lithologic sequences characterized by distinct suites of minerals that exhibit diagnostic spectral features (e.g. chlorite, epidote, amphibole and other ferrous-iron bearing minerals); other sequences were distinguished by their weathering characteristics and associated hydroxyl- and ferric-iron minerals, such as illite, smectite, and hematite. Smectite, kaolinite, opaline silica, jarosite and/or other ferric iron minerals defined narrow (< 250 m diameter) zonal patterns around Red Mountain and other potential VMS targets. Using ASTER we identified some of the known mineral deposits in the region, as well as mineralogically similar targets that may represent potential undiscovered deposits. Some known deposits were not identified and may have been obscured by vegetation- or snow-cover, or were too small to be resolved.

Geologic map of upper Eocene to Holocene volcanic and related rocks in the Cascade Range, Washington

USGS Publications Warehouse

Smith, James G.

1993-01-01

For geothermal reasons, the maps emphasize Quaternary volcanic rocks. Large igneous-related geothermal systems that have high temperatures are associated with Quaternary volcanic fields, and geothermal potential declines rapidly as age increases (Smith and Shaw, 1975). Most high-grade recoverable geothermal energy is likely to be associated with silicic volcanism less than 1 Ma. Lower grade (= lower temperature) geothermal resources may be associated with somewhat older rocks; however, volcanic rocks older than about 2 Ma are unlikely geothermal targets (Smith and Shaw, 1975).

The Zamama-Thor region of Io: Insights from a synthesis of mapping, topography, and Galileo spacecraft data

USGS Publications Warehouse

Williams, D.A.; Keszthelyi, L.P.; Schenk, P.M.; Milazzo, M.P.; Lopes, R.M.C.; Rathbun, J.A.; Greeley, R.

2005-01-01

We have studied data from the Galileo spacecraft's three remote sensing instruments (Solid-State Imager (SSI), Near-Infrared Mapping Spectrometer (NIMS), and Photopolarimeter-Radiometer (PPR)) covering the Zamama - Thor region of Io's antijovian hemisphere, and produced a geomorphological map of this region. This is the third of three regional maps we are producing from the Galileo spacecraft data. Our goal is to assess the variety of volcanic and tectonic materials and their interrelationships on Io using planetary mapping techniques, supplemented with all available Galileo remote sensing data. Based on the Galileo data analysis and our mapping, we have determined that the most recent geologic activity in the Zamama - Thor region has been dominated by two sites of large-scale volcanic surface changes. The Zamama Eruptive Center is a site of both explosive and effusive eruptions, which emanate from two relatively steep edifices (Zamama Tholi A and B) that appear to be built by both silicate and sulfur volcanism. A ???100-km long flow field formed sometime after the 1979 Voyager flybys, which appears to be a site of promethean-style compound flows, flow-front SO2 plumes, and adjacent sulfur flows. Larger, possibly stealthy, plumes have on at least one occasion during the Galileo mission tapped a source that probably includes S and/or Cl to produce a red pyroclastic deposit from the same vent from which silicate lavas were erupted. The Thor Eruptive Center, which may have been active prior to Voyager, became active again during the Galileo mission between May and August 2001. A pillanian-style eruption at Thor included the tallest plume observed to date on Io (at least 500 km high) and new dark lava flows. The plume produced a central dark pyroclastic deposit (probably silicate-rich) and an outlying white diffuse ring that is SO2-rich. Mapping shows that several of th000e new dark lava flows around the plume vent have reoccupied sites of earlier flows. Unlike most of the other pillanian eruptions observed during the Galileo mission, the 2001 Thor eruption did not produce a large red ring deposit, indicating a relative lack of S and/or Cl gases interacting with the magma during that eruption. Between these two eruptive centers are two paterae, Thomagata and Reshef. Thomagata Patera is located on a large shield-like mesa and shows no signs of activity. In contrast, Reshef Patera is located on a large, irregular mesa that is apparently undergoing degradation through erosion (perhaps from SO2 -sapping or chemical decomposition of sulfur-rich material) from multiple secondary volcanic centers. ?? 2005 Elsevier Inc. All rights reserved.

Geologic Mapping of the Chaac-Camaxtli Region of Io from Galileo Imaging Data

NASA Technical Reports Server (NTRS)

Williams, David A.; Radebaugh, Jani; Keszthelyi, Laszlo P.; McEwen, Alfred S.; Lopes, Rosaly M. C.; Doute, Sylvain; Greekely, Ronald

2003-01-01

We produced a geologic/geomorphologic map of the Chaac-Camaxtli region of Io's leading anti-Jovian hemisphere using regional resolution ( 186 m/pixel) Galileo imaging data collected during orbit I27 (February 2000) integrated with lower resolution (1.4 km/pixel) color data, along with other Galileo imaging and spectral data. This is the first regional map of Io made from Galileo data. Nine color and geomorphologic units have been mapped, and the close proximity of dark and various colored bright materials suggests that there is an intimate interaction between (presumably) silicate magmas and sulfur-bearing volatile materials that produced a variety of explosive and effusive deposits in the recent geologic past. This region of Io is dominated by 11 volcanic centers, most of which are paterae that are analogous in morphology to terrestrial calderas but larger in size. Mapping of structural features indicates that most of the active regions occur in topographic lows, and less active or inactive paterae are associated with topographic highs. This indicates that crustal thickness variations influence magma access to the surface. Surface changes in this region since the Voyager flybys are relatively minor (additional bright and dark flows, color changes), although several active vents have migrated within paterae. This observation, along with the identification of the relatively regular spacing of paterae (approx. 100 - 150 km) along a line, may indicate there are multiple interlacing fractures in the crust that serve as magma conduits from the interior. This connection between volcanism and tectonism may have implications for tidal heating mechanisms and their effect on Io's lithosphere. Some inactive patera floors may be evolving into bright plains material, which, if composed of silicates, might explain the strength of Io's crust to support steep patera walls and tall mountains.

Geologic Mapping of the Chaac-Camaxtli Region of Io from Galileo Imaging Data

NASA Technical Reports Server (NTRS)

Williams, David A.; Radebaugh, Jani; Keszthelyi, Laszlo P.; McEwen, Alfred S.; Lopes, Rosaly M. C.; Doute, Sylvain; Greeley, Ronald

2002-01-01

We produced a geologic/geomorphologic map of the Chaac-Camaxtli region of Io's leading anti-Jovian hemisphere using regional resolution (186 m/pixel) Galileo imaging data collected during orbit I27 (February 2000) integrated with lower resolution (1.4 km/pixel) color data, along with other Galileo imaging and spectral data. This is the first regional map of Io made from Galileo data. Nine color and geomorphologic units have been mapped, and the close proximity of dark and various colored bright materials suggests that there is an intimate interaction between (presumably) silicate magmas and sulfur-bearing volatile materials that produced a variety of explosive and effusive deposits in the recent geologic past. This region of Io is dominated by 11 volcanic centers, most of which are paterae that are analogous in morphology to terrestrial calderas but larger in size. Mapping of structural features indicates that most of the active regions occur in topographic lows, and less active or inactive paterae are associated with topographic highs. This indicates that crustal thickness variations influence magma access to the surface. Surface changes in this region since the Voyager flybys (1979) are relatively minor (additional bright and dark flows, color changes), although several active vents have migrated within paterae. This observation, along with the identification of the relatively regular spacing of paterae (approx. 100- 150 km) along a line, may indicate there are multiple interlacing fractures in the crust that serve as magma conduits from the interior. This connection between volcanism and tectonism may have implications for tidal heating mechanisms and their effect on Io's lithosphere. Some inactive patera floors may be evolving into bright plains material, which, if composed of silicates, might explain the strength of Io's crust to support steep patera walls and tall mountains.

Structural Analysis of Silicic Lavas Reveals the Importance of Endogenous Flow During Emplacement

NASA Astrophysics Data System (ADS)

Andrews, G. D.; Martens, A.; Isom, S.; Maxwell, A.; Brown, S. R.

2017-12-01

Recent observations of silicic lava flows in Chile strongly suggest sustained, endogeneous flow beneath an insulating carapace, where the flow advances through breakouts at the flow margin. New mapping of vertical exposures around the margin of Obsidian Dome, California, has identified discreet lobe structures in cross-section, suggesting that flow-front breakouts occured there during emplacement. The flow lobes are identified through structural measurements of flow-banding orientation and the stretching directions of vesicles. Newly acquired lidar of the Inyo Domes, including Obsidian Dome, is being analyzed to better understand the patterns of folding on the upper surface of the lavas, and to test for fold vergence patterns that may distinguish between endogenous and exogenous flow.

Cytotoxicity and osteogenic potential of silicate calcium cements as potential protective materials for pulpal revascularization.

PubMed

Bortoluzzi, Eduardo A; Niu, Li-Na; Palani, Chithra D; El-Awady, Ahmed R; Hammond, Barry D; Pei, Dan-Dan; Tian, Fu-Cong; Cutler, Christopher W; Pashley, David H; Tay, Franklin R

2015-12-01

In pulpal revascularization, a protective material is placed coronal to the blood clot to prevent recontamination and to facilitate osteogenic differentiation of mesenchymal stem cells to produce new dental tissues. Although mineral trioxide aggregate (MTA) has been the material of choice for clot protection, it is easily displaced into the clot during condensation. The present study evaluated the effects of recently introduced calcium silicate cements (Biodentine and TheraCal LC) on the viability and osteogenic differentiation of human dental pulp stem cells (hDPSCs) by comparing with MTA Angelus. Cell viability was assessed using XTT assay and flow cytometry. The osteogenic potential of hDPSCs exposed to calcium silicate cements was examined using qRT-PCR for osteogenic gene expressions, alkaline phosphatase enzyme activity, Alizarin red S staining and transmission electron microscopy of extracellular calcium deposits. Parametric statistical methods were employed for analyses of significant difference among groups, with α=0.05. The cytotoxic effects of Biodentine and TheraCal LC on hDPSCs were time- and concentration-dependent. Osteogenic differentiation of hDPSCs was enhanced after exposure to Biodentine that was depleted of its cytotoxic components. This effect was less readily observed in hDPSCs exposed to TheraCal LC, although both cements supported extracellular mineralization better than the positive control (zinc oxide-eugenol-based cement). A favorable tissue response is anticipated to occur with the use of Biodentine as a blood clot-protecting material for pulpal revascularization. Further investigations with the use of in vivo animal models are required to validate the potential adverse biological effects of TheraCal LC on hDPSCs. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Cytotoxicity and Osteogenic Potential of Silicate Calcium Cements as Potential Protective Materials for Pulpal Revascularization

PubMed Central

Bortoluzzi, Eduardo A.; Niu, Li-na; Palani, Chithra D.; El-Awady, Ahmed R.; Hammond, Barry D.; Pei, Dan-dan; Tian, Fu-cong; Cutler, Christopher W.; Pashley, David H.; Tay, Franklin R.

2016-01-01

Objectives In pulpal revascularization, a protective material is placed coronal to the blood clot to prevent recontamination and to facilitate osteogenic differentiation of mesenchynal stem cells to produce new dental tissues. Although mineral trioxide aggregate (MTA) has been the material of choice for clot protection, it is easily displaced into the clot during condensation. The present study evaluated the effects of recently-introduced calcium silicate cements (Biodentine and TheraCal LC) on the viability and osteogenic differentiation of human dental pulp stem cells (hDPSCs) by comparing with MTA Angelus. Methods Cell viability was assessed using XTT assay and flow cytometry. The osteogenic potential of hDPSCs exposed to calcium silicate cements was examined using qRT-PCR for osteogeic gene expressions, alkaline phosphatase enzyme activity, Alizarin red S staining and transmission electron microscopy of extracellular calcium deposits. Parametric statistical methods were employed for analyses of significant difference among groups, with α=0.05. Results The cytotoxic effects of Biodentine and TheraCal LC on hDPSCs were time- and concentration-dependent. Osteogenic differentiation of hDPSCs was enhanced after exposure to Biodentine that was depleted of its cytotoxic components. This effect was less readily observed in hDPSCs exposed to TheraCal LC, although both cements supported extracelluar mineralization better than the positive control (zinc oxide-eugenol–based cement). Significance A favorable tissue response is anticipated to occur with the use of Biodentine as a blood clot-protecting material for pulpal revascularizaiton. Further investigations with the use of in vivo animal models are required to validate the potential adverse biological effects of TheraCal LC on hDPSCs. PMID:26494267

Effusive silicic volcanism in the Paraná Magmatic Province, South Brazil: Evidence for locally-fed lava flows and domes from detailed field work

NASA Astrophysics Data System (ADS)

Polo, L. A.; Janasi, V. A.; Giordano, D.; Lima, E. F.; Cañon-Tapia, E.; Roverato, M.

2018-04-01

Lava flows and dome complexes of silicic composition were identified in the Lower Cretaceous Paraná Magmatic Province (PMP) at Rio Grande do Sul state, southern Brazil. Detailed mapping and image analysis reveals significant volumes of effusive deposits aligned according to main lineaments, likely representing the fissural systems that fed the three Palmas-type silicic units. Different structures indicative of effusive emplacement (lava domes, lobated flows, sheet flows and autobreccias) are very common in the study area, and are probably also more abundant than previously thought in whole PMP silicic magmatism. In fact, effusive deposits seem predominant in the three distinct silicic units identified in the area, since no remnants of pyroclastic components have been identified. The vitreous dacites that make up the upper flows of the basaltic andesite to dacite Barros Cassal sequence are clearly effusive, as indicated by their occurrence as thin sheet flows. The much thicker early Caxias do Sul dacites occur mostly as lava flow lobes and pancake-like, of low to moderate viscosity, and lava domes. The younger, high SiO2 Santa Maria rhyolite unit shows unequivocal examples of effusive deposits at its lower portion, as lobated flows formed by vesicle-rich obsidian. In spite of higher viscosities relative to the previous units ( 106 Pa·s), it is probable that the very low H2O contents 1 wt% of these rhyolite melts, associated with high discharge rates, resulted in an effusive nature in most to this unit.

Making Earth's earliest continental crust - an analogue from voluminous Neogene silicic volcanism in NE-Iceland

NASA Astrophysics Data System (ADS)

Berg, Sylvia E.; Troll, Valentin R.; Burchardt, Steffi; Riishuus, Morten S.; Deegan, Frances M.; Harris, Chris; Whitehouse, Martin J.; Gústafsson, Ludvik E.

2014-05-01

Borgarfjörður Eystri in NE-Iceland represents the second-most voluminous exposure of silicic eruptive rocks in Iceland and is a superb example of bimodal volcanism (Bunsen-Daly gap), which represents a long-standing controversy that touches on the problem of crustal growth in early Earth. The silicic rocks in NE-Iceland approach 25 % of the exposed rock mass in the region (Gústafsson et al., 1989), thus they significantly exceed the usual ≤ 12 % in Iceland as a whole (e.g. Walker, 1966; Jonasson, 2007). The origin, significance, and duration of the voluminous (> 300 km3) and dominantly explosive silicic activity in Borgarfjörður Eystri is not yet constrained (c.f. Gústafsson, 1992), leaving us unclear as to what causes silicic volcanism in otherwise basaltic provinces. Here we report SIMS zircon U-Pb ages and δ18O values from the region, which record the commencement of silicic igneous activity with rhyolite lavas at 13.5 to 12.8 Ma, closely followed by large caldera-forming ignimbrite eruptions from the Breiðavik and Dyrfjöll central volcanoes (12.4 Ma). Silicic activity ended abruptly with dacite lava at 12.1 Ma, defining a ≤ 1 Myr long window of silicic volcanism. Magma δ18O values estimated from zircon range from 3.1 to 5.5 (± 0.3; n = 170) and indicate up to 45 % assimilation of a low-δ18O component (e.g. typically δ18O = 0 ‰, Bindeman et al., 2012). A Neogene rift relocation (Martin et al., 2011) or the birth of an off-rift zone to the east of the mature rift associated with a thermal/chemical pulse in the Iceland plume (Óskarsson & Riishuus, 2013), likely brought mantle-derived magma into contact with fertile hydrothermally-altered basaltic crust. The resulting interaction triggered large-scale crustal melting and generated mixed-origin silicic melts. Such rapid formation of silicic magmas from sustained basaltic volcanism may serve as an analogue for generating continental crust in a subduction-free early Earth (e.g. ≥ 3 Ga, Kamber et al., 2005). REFERENCES: Bindeman, I.N., et al., 2012. Terra Nova 24, 227-232. Gústafsson, L.E., et al., 1989. Jökull, v. 39, 75-89. Gústafsson, L.E., 1992. PhD dissertation, Freie Universität Berlin. Jonasson, K., 2007. Journal of Geodynamics, 43, 101-117. Kamber, B.S., et al., 2005. Earth Planet. Sci. Lett., Vol. 240 (2), 276-290. Martin, E., et al., 2011. Earth Planet. Sc. Lett., 311, 28-38. Óskarsson, B.V., & Riishuus, M.S., 2013. J. Volcanol. Geoth.Res., 267, 92-118. Walker, G.P.L., 1966. Bull. Volcanol., 29 (1), 375-402.

Embryonic Methamphetamine Exposure Inhibits Methamphetamine Cue Conditioning and Reduces Dopamine Concentrations in Adult N2 C. elegans

PubMed Central

Katner, S.N.; Neal-Beliveau, B.S.; Engleman, E.A.

2016-01-01

Methamphetamine (MAP) addiction is substantially prevalent in today's society, resulting in thousands of deaths and costing billions of dollars annually. Despite the potential deleterious consequences, few studies have examined the long-term effects of embryonic MAP exposure. Using the invertebrate nematode Caenorhabditis elegans (C. elegans) allows for a controlled analysis of behavioral and neurochemical changes due to early developmental drug exposure. The objective of the current studies was to determine the long-term behavioral and neurochemical effects of embryonic exposure to MAP in C. elegans. In addition, we sought to improve our conditioning and testing procedures by utilizing liquid filtration, as opposed to agar, and smaller, 6-well testing plates to increase throughput. Wild-type N2 C. elegans were embryonically exposed to 50 μM MAP. Using classical conditioning, adult-stage C. elegans were conditioned to MAP (17 and 500 μM) in the presence of either sodium ions (Na+) or chloride (Cl-) ions as conditioned stimuli (CS+/CS-). Following conditioning, a preference test was performed by placing worms in 6-well test plates spotted with the CS+ and CS- at opposite ends of each well. A preference index (PI) was determined by counting the number of worms in the CS+ target zone divided by the total number of worms in the CS+ and CS- target zones. A food conditioning experiment was also performed in order to determine if embryonic MAP exposure affected food conditioning behavior. For the neurochemical experiments, adult worms that were embryonically exposed to MAP were analyzed for (dopamine) DA content using high performance liquid chromatography (HPLC). The liquid filtration conditioning procedure employed here in combination with the use 6-well test plates significantly decreased the time required to perform these experiments and ultimately increased throughput. The MAP conditioning data found that pairing an ion with MAP at 17 or 500 μM significantly increased the preference for that ion (CS+) in worms that were not pre-exposed to MAP. However, worms embryonically exposed to MAP did not exhibit significant drug cue conditioning. The inability of MAP exposed worms to condition to MAP was not associated with deficits in food conditioning, as MAP exposed worms exhibited a significant cue preference associated with food. Furthermore, our results found that embryonic MAP exposure reduced DA levels in adult C. elegans, which could be a key mechanism contributing to the long-term effects of embryonic MAP exposure. It is possible that embryonic MAP exposure may be impairing the ability for C. elegans to learn associations between MAP and the CS+ or inhibiting the reinforcing properties of MAP, however, our food conditioning data suggest that MAP exposed animals can form associations between cues and food. The depletion of DA levels during embryonic exposure to MAP could be responsible for driving either of these processes during adulthood. PMID:27233671

Embryonic Methamphetamine Exposure Inhibits Methamphetamine Cue Conditioning and Reduces Dopamine Concentrations in Adult N2 Caenorhabditis elegans.

PubMed

Katner, Simon N; Neal-Beliveau, Bethany S; Engleman, Eric A

2016-01-01

Methamphetamine (MAP) addiction is substantially prevalent in today's society, resulting in thousands of deaths and costing billions of dollars annually. Despite the potential deleterious consequences, few studies have examined the long-term effects of embryonic MAP exposure. Using the invertebrate nematode Caenorhabditis elegans allows for a controlled analysis of behavioral and neurochemical changes due to early developmental drug exposure. The objective of the current study was to determine the long-term behavioral and neurochemical effects of embryonic exposure to MAP in C. elegans. In addition, we sought to improve our conditioning and testing procedures by utilizing liquid filtration, as opposed to agar, and smaller, 6-well testing plates to increase throughput. Wild-type N2 C. elegans were embryonically exposed to 50 μM MAP. Using classical conditioning, adult-stage C. elegans were conditioned to MAP (17 and 500 μM) in the presence of either sodium ions (Na+) or chloride ions (Cl-) as conditioned stimuli (CS+/CS-). Following conditioning, a preference test was performed by placing worms in 6-well test plates spotted with the CS+ and CS- at opposite ends of each well. A preference index was determined by counting the number of worms in the CS+ target zone divided by the total number of worms in the CS+ and CS- target zones. A food conditioning experiment was also performed in order to determine whether embryonic MAP exposure affected food conditioning behavior. For the neurochemical experiments, adult worms that were embryonically exposed to MAP were analyzed for dopamine (DA) content using high-performance liquid chromatography. The liquid filtration conditioning procedure employed here in combination with the use of 6-well test plates significantly decreased the time required to perform these experiments and ultimately increased throughput. The MAP conditioning data found that pairing an ion with MAP at 17 or 500 μM significantly increased the preference for that ion (CS+) in worms that were not pre-exposed to MAP. However, worms embryonically exposed to MAP did not exhibit significant drug cue conditioning. The inability of MAP-exposed worms to condition to MAP was not associated with deficits in food conditioning, as MAP-exposed worms exhibited a significant cue preference associated with food. Furthermore, our results found that embryonic MAP exposure reduced DA levels in adult C. elegans, which could be a key mechanism contributing to the long-term effects of embryonic MAP exposure. It is possible that embryonic MAP exposure may be impairing the ability of C. elegans to learn associations between MAP and the CS+ or inhibiting the reinforcing properties of MAP. However, our food conditioning data suggest that MAP-exposed animals can form associations between cues and food. The depletion of DA levels during embryonic exposure to MAP could be responsible for driving either of these processes during adulthood. © 2016 S. Karger AG, Basel.

Early Age Carbonation Heat and Products of Tricalcium Silicate Paste Subject to Carbon Dioxide Curing.

PubMed

Li, Zhen; He, Zhen; Shao, Yixin

2018-05-04

This paper presents a study on the carbonation reaction heat and products of tricalcium silicate (C₃S) paste exposed to carbon dioxide (CO₂) for rapid curing. Reaction heat was measured using a retrofitted micro-calorimeter. The highest heat flow of a C₃S paste subject to carbonation curing was 200 times higher than that by hydration, and the cumulative heat released by carbonation was three times higher. The compressive strength of a C₃S paste carbonated for 2 h and 24 h was 27.5 MPa and 62.9 MPa, respectively. The 24-h carbonation strength had exceeded the hydration strength at 28 days. The CO₂ uptake of a C₃S paste carbonated for 2 h and 24 h was 17% and 26%, respectively. The X-ray diffraction (XRD), transmission electron microscope coupled with energy dispersive spectrometer (TEM-EDS), and 29 Si magic angle spinning⁻nuclear magnetic resonance ( 29 Si MAS-NMR) results showed that the products of a carbonated C₃S paste were amorphous silica (SiO₂) and calcite crystal. There was no trace of calcium silicate hydrate (C⁻S⁻H) or other polymorphs of calcium carbonate (CaCO₃) detected.

Removal of sulphur dioxide from flue gases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ersoy-Mericboyu, A.

1999-08-01

Mixtures of Ca(OH){sub 2} and different siliceous materials such as fly ash, bentonite, silica fume, and diatomite were hydrated to produce reactive SO{sub 2} sorbents. It was observed that these sorbents showed a better reactivity toward SO{sub 2} than the Ca(OH){sub 2} itself. This behavior is closely related to the pozzolanic nature of the hydrated sorbents and to the greater surface area. The reactivity of the sorbents was strongly influenced by the source of siliceous material and the hydration conditions. The total sulphation capacities of the sorbents were determined at 338 K with a synthetic gaseous mixture containing 5,000 ppmmore » SO{sub 2} and 55% relative humidity. Depending on the chemical and physical properties of the sorbents, the SO{sub 2} captures ranged from 1.20 to 5.58 mmol SO{sub 2}/g sorbent. The amount of SO{sub 2} capture increased with the increasing surface area of the sorbent. The utilization of Ca(OH){sub 2} with SO{sub 2} improved significantly when Ca(OH){sub 2} was hydrated with siliceous materials first and later exposed to SO{sub 2}.« less

Prediction of Exploration Target Areas for GEM Deposits in Mogok Stone Tract, Northern Myanmar by Integrating Remote Sensing and Geoscience Data

NASA Astrophysics Data System (ADS)

Oo, Tin Ko

2011-07-01

The Mogok Stone Tract area has long been known for world famous finest ruby since 1597. The Mogok area lies in northern Myanmar and is located at about 205.99km northeast from Mandalay, the second largest city of Myanmar. The Mogok Group of metasedimentary rocks is divided into four units: (1) Wabyudaung Marble, (2) Ayenyeinchantha Calc-silicate, (3) Gwebin Quartzite, and (4) Kabe Gneiss. Igneous rocks in the Mogok area are classified into two units: (1) Kabaing Granite and (2) Pingutaung Leucogranite. The Mogok area has a complex structure involving several folds and faults. Using marbles and calc-silicates as marker horizons, a series of anticline and syncline can be identified such as Mogok syncline, Ongaing anticline, Bawpadan syncline, and Kyatpyin anticline. All the foldings show a low-angle plunge to the south. The main precious stones of the Mogok area are ruby and sapphire; and the other important semi-precious stones are spinel, topaz, peridot, garnet, apatite, beryl, tourmaline (rubellite), quartz, diopside, fluorite, and enstatite. Geological and remote sensing data are processed to extract the indicative features of gem mineralized areas: lithology, structure, and hydrothermal alteration. Density slice version of Landsat ETM band ratios 5/7 is used to map clay alterations. Filtering Landsat ETM band 5 by using edge detection filter is applied for lineament mapping. Spatial integration of various geoscience and remote sensing data sets such as geological maps, Landsat ETM images, and the location map of gem mines show the distribution of alteration zones associated with the gem mineralization in the study area. Geographic Information System (GIS) model has been designed and implemented by ARCVIEW software package based on the overlay of lithologic, lineament, and alteration vector maps. This process has resulted in delineation of most promising areas of probable gem mineralized zones as on the output map.

ASTER spectral sensitivity of carbonate rocks - Study in Sultanate of Oman

NASA Astrophysics Data System (ADS)

Rajendran, Sankaran; Nasir, Sobhi

2014-02-01

Remote sensing satellite data plays a vital role and capable in detecting minerals and discriminating rock types for explorations of mineral resources and geological studies. Study of spectral absorption characters of remotely sensed data are under consideration by the exploration and mining companies, and demonstrating the spectral absorption characters of carbonates on the cost-effective multispectral image (rather than the hyperspectral, Lidar image) for easy understanding of all geologists and exploration communities of carbonates is very much important. The present work is an integrated study and an outcome of recently published works on the economic important carbonate rocks, includes limestone, marl, listwaenites and carbonatites occurred in parts of the Sultanate of Oman. It demonstrates the spectral sensitivity of such rocks for simple interpretation over satellite data and describes and distinguishes them based on the absorptions of carbonate minerals in the spectral bands of advanced spaceborne thermal emission and reflection radiometer (ASTER) for mapping and exploration studies. The study results that the ASTER spectral band 8 discriminates the carbonate rocks due to the presence of predominantly occurred carbonate minerals; the ASTER band 5 distinguishes the limestones and marls (more hydroxyl clay minerals) from listwaenite (hydrothermally altered rock) due to the presence of altered minerals and the ASTER band 4 detects carbonatites (ultramafic intrusive alkaline rocks) which contain relatively more silicates. The study on the intensity of the total absorptions against the reflections of these rocks shows that the limestones and marls have low intensity in absorptions (and high reflection values) due to the presence of carbonate minerals (calcite and dolomite) occurred in different proportions. The listwaenites and carbonatites have high intensity of absorptions (low reflection values) due to the occurrence of Mn-oxide in listwaenites and carbonates in carbonatites apart the influence of major carbonate minerals that occurred predominantly in these rocks. The study of ASTER thermal infrared (TIR) spectral bands distinguished the marls have low emissivity of energy due to the presence of hydroxyl bearing alumina-silicate minerals from the other rocks such as limestones, listwaenites and carbonatites which have high emissivity due to the absence of hydroxyl bearing alumina-silicate minerals and the presence of carbonate minerals and carbonates. Further, the study demonstrates and confirms the spectral sensitivity of marls and carbonatites. Marls have high reflectivity in ASTER visible near infrared (VNIR) and shortwave infrared (SWIR) spectral bands and low emissivity of energy in ASTER TIR spectral bands due to the presence of hydroxyl bearing alumina-silicate minerals. Carbonatites have low reflectivity in ASTER VNIR-SWIR spectral bands and high emissivity in ASTER TIR spectral bands due to the absence of hydroxyl bearing alumina-silicate minerals and the presence of the carbonate minerals and carbonates. These have been discussed by providing the grey scale color image of 14 ASTER spectral bands of the study sites. The study is based on the interpretation of image spectra of multispectral image conducted to map such economic valuable carbonate rocks. It provides a simple methods and basic knowledge, which are of great help to the geology and exploration communities. It is recommended to the geologists, industrialists, exploration communities of carbonates and mine owners to take up the knowledge for economic exploration of such deposits. Further, the study has proved that the technique is time and cost effective in mapping of such deposits and can be used to the areas which have extremely rugged topography occurred in similar arid region, where difficult to do exhaustive sampling and not reachable for conventional geological mapping.

Experimental Investigation on the Topotaxy of Sulfide and Silicate Melts in Peridotite: Implications for the Origin of PGE-depleted Cu-Ni Sulfide Deposit

NASA Astrophysics Data System (ADS)

Wang, Z.; Zhang, J.; Jin, Z.

2016-12-01

Cu-Ni sulfide deposit is generally considered partial melt originated from the mantle which is usually PGE-enriched. However, the largest Cu-Ni sulfide deposits of China (the Jinchuan Cu-Ni deposit) is PGE-depleted. Comparing to silicate melt, the nature and topotaxy of sulfide melt have remained poorly understood. Here we report experimental investigation on the topotaxy of sulfide and silicate melts in peridotite using a piston-cylinder press and a 5GPa Griggs-type deformation apparatus. The starting material consists of polycrystalline olivine or pyrolite and 1 wt% Fe-Ni-Cu sulfide. Hydrostatic and deformation experiments were conducted at a pressure of 1.5 GPa and a temperature of 1250°. Under hydrostatic conditions, our results reveal that the apparent dihedral angle of sulfide melt in an olivine matrix( 96°) is much larger than that of silicate + sulfide melt in pyrolite(<60°) under hydrostatic conditions. The sulfide melt pockets appear mostly as blobs in triple junctions with an immiscible Ni-poor center surrounded by a Ni-rich layer. Under deformation conditions, olivine develops pronounced fabrics with the pole of the (010) forming high concentrations approximately normal to the foliation plane and the [100] axes forming a girdle in the foliation plane. EBSD phase mapping analyses reveal strong shape preferred orientations (SPO) of sulfide +silicate melt in the 45, 90, 135 degree directions for deformation experiments indicating complete wetting of grain boundaries and forming a favorable source for ore deposits. Deformation also causes mixing of the Ni-rich and the Ni-poor sulfide melts. As the platinum-group elements(PGE) prefer to concentrate in the Ni-rich sulfide melt at high temperatures, our results suggest that the metallogenetic source of the PGE-depleted Cu-Ni deposits may have formed under relatively intense deformation and low temperatures with a small fraction of mixed sulfide and silicate melts.

Ceres' Global Cryosphere

NASA Astrophysics Data System (ADS)

Sizemore, H. G.; Prettyman, T. H.; De Sanctis, M. C.; Schmidt, B. E.; Hughson, K.; Chilton, H.; Castillo, J. C.; Platz, T.; Schorghofer, N.; Bland, M. T.; Sori, M.; Buczkowski, D.; Byrne, S.; Landis, M. E.; Fu, R.; Ermakov, A.; Raymond, C. A.; Schwartz, S. J.

2017-12-01

Prior to the arrival of the Dawn spacecraft at Ceres, the dwarf planet was anticipated to have a deep global cryosphere protected by a thin silicate lag. Gravity science along with data collected by Dawn's Framing Camera (FC), Gamma Ray and Neutron Detector (GRaND), and Visible and Infrared Mapping Spectrometer (VIR-MS) during the primary mission at Ceres have confirmed the existence of a global, silicate-rich cryosphere, and suggest the existence of deeper ice, brine, or mud layers. As such, Ceres' surface morphology has characteristics in common with both Mars and the small icy bodies of the outer solar system. We will summarize the evidence for the existence and global extent of the Cerean cryosphere. We will also discuss the range of morphological features that have been linked to subsurface ice, and highlight outstanding science questions.

Summary mineral resource appraisal of the Richfield 1 degree x 2 degrees Quadrangle, west-central Utah

USGS Publications Warehouse

Steven, Thomas August; Morris, Hal T.

1987-01-01

The mineral resource potential of the Richfield 1? x 2? quadrangle, Utah, has been appraised using geological, geophysical, geochemical, and remote-sensing techniques. These studies have led to many publications giving basic data and interpretations; of these, a series of 18 maps at 1:250,000 and 1:500,000 scales summarizing aspects of the geology, geophysics, geochemistry, and remote sensing is designated the CUSMAP (Conterminous United States Mineral Appraisal Program) folio. This circular uses the data shown on these maps to appraise the mineral resource potential of the quadrangle. The oldest rocks exposed in the Richfield quadrangle are small patches of Early Proterozoic (1.7 billion years old) gneiss and schist on the west side of the Mineral Mountains. These rocks presumably formed the basement on which many thousands of meters of Late Proterozoic, Paleozoic, and lower Mesozoic sedimentary strata were deposited. These rocks were deformed during the Late Cretaceous Sevier orogeny when Precambrian and Paleozoic strata in the western part of the quadrangle were thrust relatively eastward across Paleozoic and Mesozoic strata in the eastern part of the quadrangle. Late Cretaceous and early Tertiary highlands above the overthrust belt were eroded and much of the debris was deposited in broad basins east of the belt. Volcanism in Oligocene and earliest Miocene time formed an east-northeast-trending belt of calcalkalic volcanoes across the southern half of the quadrangle. In early Miocene time, the composition of the volcanic rocks changed to a bimodal assemblage of mafic rocks and high-silica alkali rhyolite that has been erupted episodically ever since. Syngenetic mineral resources developed during formation of both sedimentary and volcanic rocks. These include limestone and dolomite, silica-rich sandstone, metalliferous black shale, evaporite deposits, zeolite deposits, pumice, cinders and scoria, and evaporitic or diagenetic deposits in playa environments. Most of these deposits need to have markets established, or extraction and fabrication techniques developed, for them to be utilized. Most epigenetic deposits are of volcanogenic-hydrothermal origin. Deposits associated with calc-alkalic igneous activity largely contain Cu, Pb, Zn, Au, and Ag, and occur in a variety of types zoned around core intrusions. Younger deposits are mostly associated with silicic igneous centers belonging to the bimodal mafic-silicic igneous association. Resources associated with this latter group are likely to contain one or more of the elements Mo, W, U, Sn, Be, and F, as well as Pb, Zn, Au, and Ag. Alunite and kaolinite deposits are found at many mineralized centers. Most epigenetically mineralized areas expose only the upper, near-surface parts of the different hydrothermal systems; most of whatever mineral deposits formed in these systems probably still exist at depth, awaiting discovery. Our conclusion is that many mineralized areas have excellent possibilities for the occurrence of mineral resources. Each of the many identified centers of mineralization is discussed briefly in this report and an estimate made of its resource potential.

Water cycling between ocean and mantle: Super-earths need not be waterworlds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cowan, Nicolas B.; Abbot, Dorian S., E-mail: n-cowan@northwestern.edu

2014-01-20

Large terrestrial planets are expected to have muted topography and deep oceans, implying that most super-Earths should be entirely covered in water, so-called waterworlds. This is important because waterworlds lack a silicate weathering thermostat so their climate is predicted to be less stable than that of planets with exposed continents. In other words, the continuously habitable zone for waterworlds is much narrower than for Earth-like planets. A planet's water is partitioned, however, between a surface reservoir, the ocean, and an interior reservoir, the mantle. Plate tectonics transports water between these reservoirs on geological timescales. Degassing of melt at mid-ocean ridgesmore » and serpentinization of oceanic crust depend negatively and positively on seafloor pressure, respectively, providing a stabilizing feedback on long-term ocean volume. Motivated by Earth's approximately steady-state deep water cycle, we develop a two-box model of the hydrosphere and derive steady-state solutions to the water partitioning on terrestrial planets. Critically, hydrostatic seafloor pressure is proportional to surface gravity, so super-Earths with a deep water cycle will tend to store more water in the mantle. We conclude that a tectonically active terrestrial planet of any mass can maintain exposed continents if its water mass fraction is less than ∼0.2%, dramatically increasing the odds that super-Earths are habitable. The greatest source of uncertainty in our study is Earth's current mantle water inventory: the greater its value, the more robust planets are to inundation. Lastly, we discuss how future missions can test our hypothesis by mapping the oceans and continents of massive terrestrial planets.« less

Stratigraphic relationships and timing of the 2012 Havre submarine silicic volcanic eruption revealed by high resolution bathymetric mapping and observations by underwater vehicles.

NASA Astrophysics Data System (ADS)

Carey, R.; Soule, S. A.; Houghton, B. F.; White, J. D. L.; Manga, M.; Wysoczanski, R. J.; Tani, K.; McPhie, J.; Fornari, D. J.; Jutzeler, M.; Caratori Tontini, F.; Ikegami, F.; Jones, M.; Murch, A.; Fauria, K.; Mitchell, S. J.; Cahalan, R. C.; Conway, C.; McKenzie, W.

2015-12-01

The 2012 deep rhyolitic caldera eruption of Havre volcano in the Kermadec arc is the first historic observed submarine eruption that produced a pumice raft observed at the ocean's surface. Ship-based bathymetric surveys before and after the eruption permit the intricacies of eruption styles, products and timescales to be quantified. In 2015 we mapped this submarine volcano in unprecedented detail with two submergence vehicles in tandem, facilitating a wide and comprehensive geological survey and sampling mission. These efforts and observations show highly complex and often simultaneous eruptive behavior from more than 14 vents along two 3 km-long fissures that represent massive ruptures of the caldera walls. This survey also revealed an important role for pre- and inter-eruptive periods of mass wasting processes derived from the intrusion of magma and destablisation of caldera walls. The detailed characterization of the eruption products, and quantification of timescales provides the scientific community with the first glimpse of the nature of submarine, intermediate magnitude, deep silicic caldera eruptions and permits unanswered yet first order fundamental questions of submarine eruption and transport processes to be addressed in the decades to come.

Geologic map of the Lassen region, Cascade Range, USA

USGS Publications Warehouse

Clynne, Michael; Muffler, L.J.

1990-01-01

A preliminary geologic map at 1:50,000 of the Lassen region encompasses 1400 km2. The map displays many small, monogenetic volcanoes of basalt to andesite as well as three major late Pliocene and Quaternary volcanic centers that have erupted products ranging from basaltic andesite to rhyolite. The youngest of these volcanic centers is the Lassen volcanic center, active from 600,000 years B.P. to the present. A major caldera formed at 400,000 years B.P. and has subsequently been filled with silicic lavas. The Lassen geothermal system, which consists of a central vapor-dominated reservoir at a temperature of 235??C underlain by a reservoir of hot water, is centered at Bumpass Hell within Lassen Volcanic National Park.

Apatite formation on bioactive calcium-silicate cements for dentistry affects surface topography and human marrow stromal cells proliferation.

PubMed

Gandolfi, Maria Giovanna; Ciapetti, Gabriela; Taddei, Paola; Perut, Francesca; Tinti, Anna; Cardoso, Marcio Vivan; Van Meerbeek, Bart; Prati, Carlo

2010-10-01

The effect of ageing in phosphate-containing solution of bioactive calcium-silicate cements on the chemistry, morphology and topography of the surface, as well as on in vitro human marrow stromal cells viability and proliferation was investigated. A calcium-silicate cement (wTC) mainly based on dicalcium-silicate and tricalcium-silicate was prepared. Alpha-TCP was added to wTC to obtain wTC-TCP. Bismuth oxide was inserted in wTC to prepare a radiopaque cement (wTC-Bi). A commercial calcium-silicate cement (ProRoot MTA) was tested as control. Cement disks were aged in DPBS for 5 h ('fresh samples'), 14 and 28 days, and analyzed by ESEM/EDX, SEM/EDX, ATR-FTIR, micro-Raman techniques and scanning white-light interferometry. Proliferation, LDH release, ALP activity and collagen production of human marrow stromal cells (MSC) seeded for 1-28 days on the cements were evaluated. Fresh samples exposed a surface mainly composed of calcium-silicate hydrates CSH (from the hydration of belite and alite), calcium hydroxide, calcium carbonate, and ettringite. Apatite nano-spherulites rapidly precipitated on cement surfaces within 5 h. On wTC-TCP the Ca-P deposits appeared thicker than on the other cements. Aged cements showed an irregular porous calcium-phosphate (Ca-P) coating, formed by aggregated apatite spherulites with interspersed calcite crystals. All the experimental cements exerted no acute toxicity in the cell assay system and allowed cell growth. Using biochemical results, the scores were: fresh cements>aged cements for cell proliferation and ALP activity (except for wTC-Bi), whereas fresh cements

Silica-Induced Protein (Sip) in Thermophilic Bacterium Thermus thermophilus Responds to Low Iron Availability

PubMed Central

Fujino, Yasuhiro; Nagayoshi, Yuko; Iwase, Makoto; Yokoyama, Takushi; Ohshima, Toshihisa

2016-01-01

ABSTRACT Thermus thermophilus HB8 expresses silica-induced protein (Sip) when cultured in medium containing supersaturated silicic acids. Using genomic information, Sip was identified as a Fe3+-binding ABC transporter. Detection of a 1-kb hybridized band in Northern analysis revealed that sip transcription is monocistronic and that sip has its own terminator and promoter. The sequence of the sip promoter showed homology with that of the σA-dependent promoter, which is known as a housekeeping promoter in HB8. Considering that sip is transcribed when supersaturated silicic acids are added, the existence of a repressor is presumed. DNA microarray analysis suggested that supersaturated silicic acids and iron deficiency affect Thermus cells similarly, and enhanced sip transcription was detected under both conditions. This suggested that sip transcription was initiated by iron deficiency and that the ferric uptake regulator (Fur) controlled the transcription. Three Fur gene homologues (TTHA0255, TTHA0344, and TTHA1292) have been annotated in the HB8 genome, and electrophoretic mobility shift assays revealed that the TTHA0344 product interacts with the sip promoter region. In medium containing supersaturated silicic acids, free Fe3+ levels were decreased due to Fe3+ immobilization on colloidal silica. This suggests that, because Fe3+ ions are captured by colloidal silica in geothermal water, Thermus cells are continuously exposed to the risk of iron deficiency. Considering that Sip is involved in iron acquisition, Sip production may be a strategy to survive under conditions of low iron availability in geothermal water. IMPORTANCE The thermophilic bacterium Thermus thermophilus HB8 produces silica-induced protein (Sip) in the presence of supersaturated silicic acids. Sip has homology with iron-binding ABC transporter; however, the mechanism by which Sip expression is induced by silicic acids remains unexplained. We demonstrate that Sip captures iron and its transcription is regulated by the repressor ferric uptake regulator (Fur). This implies that Sip is expressed with iron deficiency. In addition, it is suggested that negatively charged colloidal silica in supersaturated solution absorbs Fe3+ ions and decreases iron availability. Considering that geothermal water contains ample silicic acids, it is suggested that thermophilic bacteria are always facing iron starvation. Sip production may be a strategy for surviving under conditions of low iron availability in geothermal water. PMID:26994077

Predicting the dissolution kinetics of silicate glasses using machine learning

NASA Astrophysics Data System (ADS)

Anoop Krishnan, N. M.; Mangalathu, Sujith; Smedskjaer, Morten M.; Tandia, Adama; Burton, Henry; Bauchy, Mathieu

2018-05-01

Predicting the dissolution rates of silicate glasses in aqueous conditions is a complex task as the underlying mechanism(s) remain poorly understood and the dissolution kinetics can depend on a large number of intrinsic and extrinsic factors. Here, we assess the potential of data-driven models based on machine learning to predict the dissolution rates of various aluminosilicate glasses exposed to a wide range of solution pH values, from acidic to caustic conditions. Four classes of machine learning methods are investigated, namely, linear regression, support vector machine regression, random forest, and artificial neural network. We observe that, although linear methods all fail to describe the dissolution kinetics, the artificial neural network approach offers excellent predictions, thanks to its inherent ability to handle non-linear data. Overall, we suggest that a more extensive use of machine learning approaches could significantly accelerate the design of novel glasses with tailored properties.

Eruptive history and tectonic setting of Medicine Lake Volcano, a large rear-arc volcano in the southern Cascades

USGS Publications Warehouse

Donnelly-Nolan, J. M.; Grove, T.L.; Lanphere, M.A.; Champion, D.E.; Ramsey, D.W.

2008-01-01

Medicine Lake Volcano (MLV), located in the southern Cascades ??? 55??km east-northeast of contemporaneous Mount Shasta, has been found by exploratory geothermal drilling to have a surprisingly silicic core mantled by mafic lavas. This unexpected result is very different from the long-held view derived from previous mapping of exposed geology that MLV is a dominantly basaltic shield volcano. Detailed mapping shows that < 6% of the ??? 2000??km2 of mapped MLV lavas on this southern Cascade Range shield-shaped edifice are rhyolitic and dacitic, but drill holes on the edifice penetrated more than 30% silicic lava. Argon dating yields ages in the range ??? 475 to 300??ka for early rhyolites. Dates on the stratigraphically lowest mafic lavas at MLV fall into this time frame as well, indicating that volcanism at MLV began about half a million years ago. Mafic compositions apparently did not dominate until ??? 300??ka. Rhyolite eruptions were scarce post-300??ka until late Holocene time. However, a dacite episode at ??? 200 to ??? 180??ka included the volcano's only ash-flow tuff, which was erupted from within the summit caldera. At ??? 100??ka, compositionally distinctive high-Na andesite and minor dacite built most of the present caldera rim. Eruption of these lavas was followed soon after by several large basalt flows, such that the combined area covered by eruptions between 100??ka and postglacial time amounts to nearly two-thirds of the volcano's area. Postglacial eruptive activity was strongly episodic and also covered a disproportionate amount of area. The volcano has erupted 9 times in the past 5200??years, one of the highest rates of late Holocene eruptive activity in the Cascades. Estimated volume of MLV is ??? 600??km3, giving an overall effusion rate of ??? 1.2??km3 per thousand years, although the rate for the past 100??kyr may be only half that. During much of the volcano's history, both dry HAOT (high-alumina olivine tholeiite) and hydrous calcalkaline basalts erupted together in close temporal and spatial proximity. Petrologic studies indicate that the HAOT magmas were derived by dry melting of spinel peridotite mantle near the crust mantle boundary. Subduction-derived H2O-rich fluids played an important role in the generation of calcalkaline magmas. Petrology, geochemistry and proximity indicate that MLV is part of the Cascades magmatic arc and not a Basin and Range volcano, although Basin and Range extension impinges on the volcano and strongly influences its eruptive style. MLV may be analogous to Mount Adams in southern Washington, but not, as sometimes proposed, to the older distributed back-arc Simcoe Mountains volcanic field.

The influence of object pre-exposure on two-year-olds' disambiguation of novel labels.

PubMed

Graham, Susan A; Turner, Juanita N; Henderson, Annette M E

2005-02-01

We investigated whether manipulating the perceived novelty of nameless objects would influence two-year-olds' tendency to map novel words to these objects. In Experiment 1, children who had been pre-exposed to target nameless objects were more likely to map novel words onto those objects than children who were not pre-exposed to the objects or children who were pre-exposed to non-target members of the nameless object categories. In Experiment 2, children who were pre-exposed to a nameless object were more likely to assign the novel label to that object than to either a familiar object or an unfamiliar object that had not been pre-exposed. The results of these studies suggest that reducing the novelty of nameless objects increases two-year-olds' tendency to map a novel word to a nameless object.

Winter nutrient behaviours in the Pearl River estuary

NASA Astrophysics Data System (ADS)

Wang, G.; Jin, S.; Du, M.

2017-12-01

Nutrient (nitrate, nitrite, ammonium, phosphate, and silicate) mapping and time-series investigation were carried out in winter in the Pearl River estuary, China. These nutrients behaved non-conservatively in the upper estuary. In the middle and lower estuary, however, nitrate and silicate seemed to be controled by physical mixing, while additions of nitrite, ammonium, and phosphate were found in the middle estuary. Nitrate was the dominant disslved inorganic nitrogen, with a fraction of more than 2/3. From the upper to the lower estuary the N:P ratio decreased from more than 200 to near the Redfield ratio of 16. Nutrients near the surface behaved almost the same as near the bottom in the water column at both the uppper and lower estuary. During a tidal cycle these nutrients seemed to be regulated more by physical mixing than by other processes.

The Physical and Petrologic Evolution of a Multi-vent Volcanic Field Associated With Yellowstone-Newberry Volcanism

NASA Astrophysics Data System (ADS)

Brueseke, M. E.; Hart, W. K.

2004-12-01

The Santa Rosa-Calico volcanic field (SC) of northern Nevada is perhaps the most chemically and physically diverse of all volcanic fields associated with mid-Miocene northwestern USA volcanism. SC volcanism occurred from 16.5 to 14 Ma and was characterized by the eruption of a complete compositional spectrum from basalt through high-Si rhyolite. Locally derived tholeiitic lava flows and shallow intrusive bodies are chemically and isotopically identical to the Steens Basalt (87/86Sri=<0.7040), the Oregon Plateau-wide mid-Miocene flood basalt. Andesite-dacite lava flows are exposed as at least four geographically and chemically distinct packages representing products of multiple, discrete magmatic systems. The most voluminous of these is calc-alkaline and characterized by abundant granitoid and mafic xenoliths/xenocrysts and radiogenic Sr isotopic ratios. Subalkaline silicic lava flows, domes, and shallow intrusive bodies define three diffuse north-south trending zones. Textural, chemical, and isotopic variability within the silicic units is linked to their spatial and temporal distribution, again necessitating the existence of multiple magmatic systems. The youngest locally derived silicic units are ash flows exposed in the central portion of the SC that erupted in actively forming sedimentary basins at ˜15.4 Ma. Underlying the 400-1500m thick package of SC volcanic rocks are temporally ( ˜103 and ˜85 Ma), chemically, and isotopically (87/86Sr at 16 Ma= 0.7045 to 0.7058 and 0.7061 to >0.7070) heterogeneous granitoid plutons and a package of ˜20-23 Ma calc-alkaline, arc-related intermediate lava flows. The observed disequilibrium textures, xenoliths, and chemical/isotopic diversity suggests that upwelling Steens magma interacted with local crust, siliceous crustal melts, and the mafic plutonic roots of early Miocene arc volcanism in multiple magmatic systems characterized by heterogeneous open system processes. The formation of these systems is tectonically controlled as evidenced by magma eruption/ascent along active zones of lithospheric extension. Thus, the observed physical and chemical diversity in this volcanic field is attributed to a combination of factors; tectonic setting, availability of upwelling mafic magma(s), nature of pre-Miocene crustal addition and lithospheric modification, and the resulting array of magma sources and petrogenetic processes.

Mechanical properties of silicate glasses exposed to a low-Earth orbit

NASA Technical Reports Server (NTRS)

Wiedlocher, David E.; Tucker, Dennis S.; Nichols, Ron; Kinser, Donald L.

1992-01-01

The effects of a 5.8 year exposure to low earth orbit environment upon the mechanical properties of commercial optical fused silica, low iron soda-lime-silica, Pyrex 7740, Vycor 7913, BK-7, and the glass ceramic Zerodur were examined. Mechanical testing employed the ASTM-F-394 piston on 3-ball method in a liquid nitrogen environment. Samples were exposed on the Long Duration Exposure Facility (LDEF) in two locations. Impacts were observed on all specimens except Vycor. Weibull analysis as well as a standard statistical evaluation were conducted. The Weibull analysis revealed no differences between control samples and the two exposed samples. We thus concluded that radiation components of the Earth orbital environment did not degrade the mechanical strength of the samples examined within the limits of experimental error. The upper bound of strength degradation for meteorite impacted samples based upon statistical analysis and observation was 50 percent.

Early Age Carbonation Heat and Products of Tricalcium Silicate Paste Subject to Carbon Dioxide Curing

PubMed Central

Li, Zhen; He, Zhen; Shao, Yixin

2018-01-01

This paper presents a study on the carbonation reaction heat and products of tricalcium silicate (C3S) paste exposed to carbon dioxide (CO2) for rapid curing. Reaction heat was measured using a retrofitted micro-calorimeter. The highest heat flow of a C3S paste subject to carbonation curing was 200 times higher than that by hydration, and the cumulative heat released by carbonation was three times higher. The compressive strength of a C3S paste carbonated for 2 h and 24 h was 27.5 MPa and 62.9 MPa, respectively. The 24-h carbonation strength had exceeded the hydration strength at 28 days. The CO2 uptake of a C3S paste carbonated for 2 h and 24 h was 17% and 26%, respectively. The X-ray diffraction (XRD), transmission electron microscope coupled with energy dispersive spectrometer (TEM-EDS), and 29Si magic angle spinning–nuclear magnetic resonance (29Si MAS-NMR) results showed that the products of a carbonated C3S paste were amorphous silica (SiO2) and calcite crystal. There was no trace of calcium silicate hydrate (C–S–H) or other polymorphs of calcium carbonate (CaCO3) detected. PMID:29734681

Activity and diversity of methane-oxidizing bacteria in glacier forefields on siliceous and calcareous bedrock

NASA Astrophysics Data System (ADS)

Nauer, P. A.; Dam, B.; Liesack, W.; Zeyer, J.; Schroth, M. H.

2012-01-01

The global methane (CH4) cycle is largely driven by methanogenic archaea and methane-oxidizing bacteria (MOB), but little is known about their activity and diversity in pioneer ecosystems. We conducted a field survey in forefields of 13 receding Swiss glaciers on both siliceous and calcareous bedrock to investigate and quantify CH4 turnover based on soil-gas CH4 concentration profiles, and to characterize MOB communities using pmoA sequencing and T-RFLP. Methane turnover was fundamentally different in the two bedrock categories. Of the 36 CH4 concentration profiles from siliceous locations, 11 showed atmospheric CH4 consumption at concentrations of ∼1-2 μl l-1 with soil-atmosphere CH4 fluxes of -0.14 to -1.1 mg m-2 d-1. Another 11 profiles showed no apparent activity, while the remaining 14 exhibited slightly increased CH4 concentrations of ∼2-10 μl l-1, most likely due to microsite methanogenesis. In contrast, all profiles from calcareous sites suggested a substantial, yet unknown CH4 source below our sampling zone, with soil-gas CH4 concentrations reaching up to 1400 μl l-1. Remarkably, most soils oxidized ∼90% of the deep-soil CH4, resulting in soil-atmosphere fluxes of 0.12 to 31 mg m-2 d-1. MOB showed limited diversity in both siliceous and calcareous forefields: all identified pmoA sequences formed only 5 OTUs and, with one exception, could be assigned to either Methylocystis or the as-yet-uncultivated Upland Soil Cluster γ (USCγ). The latter dominated T-RFLP patterns of all siliceous and most calcareous samples, while Methylocystis dominated in 4 calcareous samples. As Type I MOB are widespread in cold climate habitats with elevated CH4 concentrations, USCγ might be the corresponding Type I MOBs in habitats exposed to near-atmospheric CH4 concentrations.

The Diversity and Evolution of Different type Granitoids in Eastern Dharwar Craton: Evidence from "Arc-Plume" Collision in Neoarchaean

NASA Astrophysics Data System (ADS)

Nandy, J.; Dey, S.

2017-12-01

Neoarchaean crustal growth, role of plate tectonics and potential secular changes is still disoriented in Dharwar craton. To provide constraints on these questions, geochronological and geochemical data are presented on the unstudied granitoids associated with Kadiri greenstone belt, eastern Dharwar craton. Five diverse type of granitoids suites are identified in that area. Field setting, petrography, whole rock geochemistry study with Sm-Nd isotopes and zircon dates help to identify their source and petrogenesis. Along the eastern margin of the Kadiri belt a sanukitoid-like granitoid body is exposed which was probably derived from a metasomatised mantle wedge above a subduction zone followed by some older crustal contamination. Along the western margin transitional TTG is exposed displaying an intrusive relation with Kadiri dacite-rhyolite. This suite is interpreted to be derived from a mafic source with some enriched crustal component. Further east and west vast area is occupied highly silicic biotite monzogranite which is enriched in LILE, high K2O/Na2O. These granitoids are product of intracrustal shallow melting. At the south-eastern tip of the Kadiri belt occurs a well-foliated and banded transitional TTG which was probably derived from melting of mafic source with some contribution of felsic crustal material. At the north-eastern tip of the belt a highly silicic ferroan granitoid is exposed. Geochemical characteristics indicate that it is A-type granite, produced from shallow melting of a felsic crustal source. The basalt in greenstone belt is generated in oceanic plateau setting and granitoids in arc setting in different time. A tectonic scenario envisaging collision between an arc and oceanic plateau followed by repeated slab break-off and crustal recycling is proposed to explain the evolution of the terrain.

Effect of Exposed Surface Area, Volume and Environmental pH on the Calcium Ion Release of Three Commercially Available Tricalcium Silicate Based Dental Cements.

PubMed

Rajasekharan, Sivaprakash; Vercruysse, Chris; Martens, Luc; Verbeeck, Ronald

2018-01-13

Tricalcium silicate cements (TSC) are used in dental traumatology and endodontics for their bioactivity which is mostly attributed to formation of calcium hydroxide during TSC hydration and its subsequent release of calcium and hydroxide ions. The aim of this study was to determine the effect of volume (Vol), exposed surface area (ESA) and pH of surrounding medium on calcium ion release. Three commercially available hydraulic alkaline dental cements were mixed and condensed into cylindrical tubes of varying length and diameter ( n = 6/group). For the effect of ESA and Vol, tubes were immersed in 10 mL of deionized water. To analyze the effect of environmental pH, the tubes were randomly immersed in 10 mL of buffer solutions with varying pH (10.4, 7.4 or 4.4). The solutions were collected and renewed at various time intervals. pH and/or calcium ion release was measured using a pH glass electrode and atomic absorption spectrophotometer respectively. The change of pH, short-term calcium ion release and rate at which calcium ion release reaches maximum were dependent on ESA ( p < 0.05) while maximum calcium ion release was dependent on Vol of TSC ( p < 0.05). Maximum calcium ion release was significantly higher in acidic solution followed by neutral and alkaline solution ( p < 0.05).

Effect of Exposed Surface Area, Volume and Environmental pH on the Calcium Ion Release of Three Commercially Available Tricalcium Silicate Based Dental Cements

PubMed Central

Rajasekharan, Sivaprakash; Vercruysse, Chris; Martens, Luc; Verbeeck, Ronald

2018-01-01

Tricalcium silicate cements (TSC) are used in dental traumatology and endodontics for their bioactivity which is mostly attributed to formation of calcium hydroxide during TSC hydration and its subsequent release of calcium and hydroxide ions. The aim of this study was to determine the effect of volume (Vol), exposed surface area (ESA) and pH of surrounding medium on calcium ion release. Three commercially available hydraulic alkaline dental cements were mixed and condensed into cylindrical tubes of varying length and diameter (n = 6/group). For the effect of ESA and Vol, tubes were immersed in 10 mL of deionized water. To analyze the effect of environmental pH, the tubes were randomly immersed in 10 mL of buffer solutions with varying pH (10.4, 7.4 or 4.4). The solutions were collected and renewed at various time intervals. pH and/or calcium ion release was measured using a pH glass electrode and atomic absorption spectrophotometer respectively. The change of pH, short-term calcium ion release and rate at which calcium ion release reaches maximum were dependent on ESA (p < 0.05) while maximum calcium ion release was dependent on Vol of TSC (p < 0.05). Maximum calcium ion release was significantly higher in acidic solution followed by neutral and alkaline solution (p < 0.05). PMID:29342837

Allochthonous Addition of Meteoritic Organics to the Lunar Regolith

NASA Technical Reports Server (NTRS)

Thomas-Keprta, K. L.; Clemett, S.; Ross, D. K.; Le, L.; Rahman, Z.; McKay, D. S.; Gibson, E. K.; Gonzalez, C.

2013-01-01

Preparation of lunar samples 74220,861 was discussed in detail in [3, 4]. Our analysis sequence was as follows: optical microscopy, UV fluorescence imaging, -Raman, FESEM-EDX imaging and mapping, FETEMEDX imaging and mapping of a Focused Ion Beam (FIB) extracted section, and NanoSIMs analysis. We observed fluffytextured C-rich regions of interest (ROI) on three different volcanic glass beads. Each ROI was several m2 in size and fluoresced when exposed to UV. Using FESEM/EDX, the largest ROI measured 36 m and was located on an edge of a plateau located on the uppermost surface of the bead. The ROI was covered on one edge by a siliceous filament emanating from the plateau surface indicating it was attached to the bead while on the Moon. EDX mapping of the ROI shows it is composed primarily of heterogeneously distributed C. Embedded with the carbonaceous phase are localized concentrations of Si, Fe, Al and Ti indicating the presence of glass and/or minerals grains. -Raman showed strong D- and G-bands and their associated second order bands; intensity and location of these bands indicates the carbonaceous matter is structurally disorganized. A TEM thin section was extracted from the surface of a glass bead using FIB microscopy. High resolution TEM imaging and selected area electron diffraction demonstrate the carbonaceous layer to be amorphous; it lacked any long or short range order characteristic of micro- or nanocrystalline graphite. Additionally TEM imaging also revealed the presence of submicron mineral grains, typically < 50 nm in size, dispersed within the carbonaceous layer. NanoSIMs data will be presented and discussed at the meeting. Given the noted similarities between the carbonaceous matter present on 74220 glass beads and meteoritic kerogen, we suggest the allochthonous addition of meteoritic organics as the most probable source for the C-rich ROIs.

Branchial and renal pathology in the fish exposed chronically to methoxy ethyl mercuric chloride

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gill, T.S.; Pant, J.C.; Tewari, H.

1988-08-01

Pathological manifestations causally related to pesticide poisoning have been described in both surficial and internal tissues of the fishes. Among the various organomercurials are phenyl mercuric acetate, methyl mercuric dicyanidiamide, methoxy ethyl mercuric chloride, methoxy ethyl mercuric silicate etc. Of these, the methoxy ethyl mercuric chloride (MEMC) is used in agriculture as an antifungal seed dressing, and its toxicity is primarily manifest in the Hg/sup 2 +/ ion. This report describes pathogenesis of branchial and renal lesions in the common freshwater fish, Puntius conchonius exposed chronically to sublethal levels of MEMC. Prior to this, alterations in the peripheral blood andmore » metabolite levels in response to experimental MEMC poisoning have been demonstrated in this species.« less

Origin of silicic crust by rifting and bimodal plume volcanism in the Afar Depression

NASA Astrophysics Data System (ADS)

Ghatak, A.; Basu, A. R.; Ebinger, C. J.

2010-12-01

The youngest mantle plume province worldwide occurs at the seismically and volcanically active East African - Red Sea - Gulf of Aden (Afar) triple junction, where one or more upwellings has impinged the thick cratonic lithosphere since ~45 Ma. A spectacular example of magmatism in the Afar depression is seen in the present to < 2 Ma old bimodal fissural mafic and peralkaline silicic eruptions in the ~60 km-long Dabbahu-Manda Hararo (DMH) Rift. In this study we report major, trace elements, and Nd-Sr-Pb isotopes in recent basaltic and silicic rocks originating from the center of the DMH rift segment, exposed along the rift axis and flanks of this segment. The rare earth element (REE) patterns of the silicic rocks and basalts are different in two significant ways: (1) the silicic rocks show a prominent positive Ce-anomaly that is extremely rare in volcanic rocks; and (2) this positive Ce-anomaly is accompanied by a strong negative Eu-anomaly. These anomalies are absent in the basaltic rocks. The positive Ce-anomaly is probably due to interaction in a magma chamber, similar in composition to the basalts, with deep saline aquifer or brines that typically show positive Ce-anomaly. The REE patterns of the two lava groups are interpreted to be due to fractional crystallization of plagioclase in a magma chamber similar in REE composition as the basalts that erupted in the DMH segments. We interpret the silicic rocks to be residues after ~20% fractional crystallization of plagioclase in the DMH basalts. The Nd-Pb isotopic composition of the basalts and rhyolites of the DMH are similar to the Ethiopian plume as defined by the ~30 Ma old Ethiopian flood basalts. Based on their high 3He/4He ratios (R/RA ~30) and Nd-Sr-Pb isotopic data, the source of the Ethiopian plume is generally believed to be in the lower mantle. Therefore, the similarity of the Nd-Pb and Pb-Pb isotopic variations between the Ethiopian plume and the DMH lavas indicates that these lavas were sourced from the lower mantle, and this source zone showed little variation over the past 30 Ma. Some of the silicic lavas fall distinctly outside the plume field toward more radiogenic 87Sr/86Sr at relatively restricted Nd and Pb isotopic compositions. This excursion in Sr-isotopic ratios of the silicic lavas, in concert with their positive Ce-anomaly, is interpreted to be due to mixing of the Afar plume derived basaltic magma with fluids from saline aquifers. We conclude that the bimodal lavas are consanguineous, the silicic lavas being generated by fractional crystallization of plagioclase in a lower mantle plume-derived basaltic magma-chamber, caused by the interaction with saline aquifers. The generation of bimodal volcanism from parental primitive basalts without any contribution from pre-existing continental crust in Dabbahu may explain other similar intraplate magmatism including early Archean-Hadean continental crust formation prior to onset of arc-volcanism.

An AMS study of different silicic units from the southern Paraná-Etendeka Magmatic Province in Brazil: Implications for the identification of flow directions and local sources

NASA Astrophysics Data System (ADS)

Guimarães, L. F.; Raposo, M. I. B.; Janasi, V. A.; Cañón-Tapia, E.; Polo, L. A.

2018-04-01

In the Southern portion of the Paraná-Etendeka Magmatic Province in Brazil, extensive silicic (dacite-rhyolite) deposits occur at the top of a sequence of low-Ti pahoehoe to rubbly basalts. The internal architecture of the silicic deposits and their eruptive style, as well as the location of their sources are still unsatisfactorily known. In an attempt to provide independent evidence for flow directions in deposits previously characterized as effusive, and test the hypothesis of local sources, we carried out anisotropy of magnetic susceptibility (AMS) studies on the two main silicic units (Caxias do Sul dacites and Santa Maria Rhyolites) with the best exposures in an area previously mapped in detail. Magnetic anisotropies were determined on oriented cylindrical specimens from a total of 28 sites. Rock magnetism properties indicate that "pseudo-single-domain" magnetite carries the fabrics and the remanence. Magnetic fabrics were determined by applying anisotropy of low-field magnetic susceptibility (AMS) and anisotropy of anhysteretic remanent magnetization (AARM). Both AMS and AARM tensors are coaxial, indicating that the AMS fabric is not affected by the effect of magnetite single-domain grains. Magnetic data from several dacitic coulées (Caxias do Sul unit) indicate flows from SE to NW. The location and spatial distribution of these lavas support the hypothesis of local sources, aligned along a NE-SW trend. These data are in agreement with the alignments of structures (dome-shaped hills) observed in field work and DEM images. On the other hand, magnetic data obtained in Santa Maria rhyolites indicate that flow directions in two different areas are distinct (towards NW/NE and W), suggesting that they derived from different emission centers. So, regarding the silicic volcanism in the studied region, our data do not support the model which classifies the entire silicic volcanism of the province as extensive rheomorphic pyroclastic deposits released from a central conduit. In contrast, we propose the occurrence of local volcanic events, implying in the existence of different sources, possibly characterized by local emission centers.

Geology of parts of the Johnny Gulch quadrangle, Montana

USGS Publications Warehouse

Freeman, Val L.

1954-01-01

An area of about 35 square miles, situated about 30 miles southeast of Helena, Montana, was mapped during the summer of 1952 at a scale of l:24, 000. The area includes a part of the eastern foothills of the Elkhorn Mountains, and is underlain by sedimentary mad volcanic rocks of Cretaceous age that were intruded during late Cretaceous or early Tertiary time by several types of igneous rocks. The oldest rocks in the map area are the nonmarine sandstone, shale, and limestone of the Kootenai formation. These are overlain disconformably by the black shale siltstone, sandstone, and siliceous mudstone of the Colorado group that is subdivided into three map units; a lower black shale unit composed of black shale and silty shale with a basal clean sandstone, all of probable marine origin; a middle siliceous unit composed of sandstone, siltstone, and siliceous mudstone of both marine and nonmarine origin; and an upper black unit composed of black shale of marine origin. Conformably above the Colorado group are crystal lithic turfs of the Slim Sam formation; in places theme grade into and in other places are unconformably overlain by the Elkhorn Mountains volcanics composed of crystal tuff, breccia, flows, and bedded tuff of andesitic composition. The rocks of the Elkhorn Mountains volcanics and older formations have been intruded by diorite porphyry and related rocks and by hornblende quartz monzonite. The diorite porphyry and related rocks include hornblende diorite porphyry, hornblende augite diorite porphyry, augite diorite porphyry, and basalt. Resting with marked unconformity upon older rocks are volcanic sedimentary rocks of early Tertiary age that are locally overlain by thin rhyolite flows. Late Tertiary and Quaternary fans overlie the rhyolite flows. Alluvium, talus, and other mantle are present in small amounts in many parts of the area. The sedimentary rocks of the area mapped form a part of the east flank of a major anticline. A major north-south syncline to the north of map area is believed to have been deflected to the east of the area because of the rigidity of large irregular plutons of diorite porphyry. The location of the plutons may have been controlled by the initiation of the major syncline, by a postulated pre-intrusive fault, or by both. Most of the small-scale structural features are related to the emplacement of the plutons. During emplacement the intruded sediments yielded either by faulting or by folding; the deeper rocks failed by faulting and the shallower rocks failed by folding. The area contains deposits of gold, silver, copper, lead, and zinc, none of which are currently being mined; and a deposit of magnetite which is being mined for use in cement.

Geophysical interpretation of U, Th, and rare earth element mineralization of the Bokan Mountain peralkaline granite complex, Prince of Wales Island, southeast Alaska

USGS Publications Warehouse

McCafferty, Anne E.; Stoeser, Douglas B.; Van Gosen, Bradley S.

2014-01-01

A prospectivity map for rare earth element (REE) mineralization at the Bokan Mountain peralkaline granite complex, Prince of Wales Island, southeastern Alaska, was calculated from high-resolution airborne gamma-ray data. The map displays areas with similar radioelement concentrations as those over the Dotson REE-vein-dike system, which is characterized by moderately high %K, eU, and eTh (%K, percent potassium; eU, equivalent parts per million uranium; and eTh, equivalent parts per million thorium). Gamma-ray concentrations of rocks that share a similar range as those over the Dotson zone are inferred to locate high concentrations of REE-bearing minerals. An approximately 1300-m-long prospective tract corresponds to shallowly exposed locations of the Dotson zone. Prospective areas of REE mineralization also occur in continuous swaths along the outer edge of the pluton, over known but undeveloped REE occurrences, and within discrete regions in the older Paleozoic country rocks. Detailed mineralogical examinations of samples from the Dotson zone provide a means to understand the possible causes of the airborne Th and U anomalies and their relation to REE minerals. Thorium is sited primarily in thorite. Uranium also occurs in thorite and in a complex suite of ±Ti±Nb±Y oxide minerals, which include fergusonite, polycrase, and aeschynite. These oxides, along with Y-silicates, are the chief heavy REE (HREE)-bearing minerals. Hence, the eU anomalies, in particular, may indicate other occurrences of similar HREE-enrichment. Uranium and Th chemistry along the Dotson zone showed elevated U and total REEs east of the Camp Creek fault, which suggested the potential for increased HREEs based on their association with U-oxide minerals. A uranium prospectivity map, based on signatures present over the Ross-Adams mine area, was characterized by extremely high radioelement values. Known uranium deposits were identified in the U-prospectivity map, but the largest tract occurs over a radioelement-rich granite phase within the pluton that is likely not related to mineralization. Neither mineralization type displays a well-defined airborne magnetic signature.

Thermal Emission Variability of Zamama, Culann and Tupan on Io Using Galileo Near-Infrared Mapping Spectrometer (NIMS) Data

NASA Technical Reports Server (NTRS)

Ennis, M. E.; Davies, A. G.

2005-01-01

The Jovian satellite Io is the most volcanically active body in the Solar System. Previous analyses [e.g., 1-4] indicate the presence of high-temperature silicate volcanism on Io, similar to silicate volcanism occurring on Earth. Instruments onboard the Galileo spacecraft, especially the Near Infrared Mapping Spectrometer (NIMS) and the Solid State Imager (SSI), provided much data of Io s active volcanoes throughout the duration of the Galileo mission (June 1996-September 2003). NIMS data is particularly sensitive to thermal emission from active and cooling lava over cooling times of seconds to a few years. The objective of this ongoing study of Io s volcanism is to determine the variability of thermal emission from volcanoes on Io s surface, in order to better understand the styles of eruption, and to constrain the volumes of material erupted. Ultimately, this will help to constrain the contribution of active volcanism to Io s thermal budget. Data have been analyzed for the volcano Zamama, located at 173 W, 21 N, and the power output of Zamama, the volumes of lava being erupted, and the eruption rate determined. Culann and Tupan have also been analysed in this way. This abstract primarily concentrates on Zamama.

Ca isotopes, chemical weathering, and geomorphic controls on long-term climate

NASA Astrophysics Data System (ADS)

Moore, J.; Jacobson, A. D.; Holmden, C. E.; Craw, D.

2009-12-01

Calcium isotope geochemistry (δ44Ca) offers a unique opportunity to directly quantify proportions of riverine Ca originating from silicate versus carbonate weathering, which is essential for understanding how geomorphic processes affecting landscape evolution, such as tectonic uplift and glaciation, influence the long-term cycling of atmospheric CO2. We measured the elemental and δ44Ca chemistry of river and rock samples from the New Zealand Southern Alps. In combination with our geochemical data, we used runoff and suspended sediment fluxes to elucidate relationships between chemical weathering, mechanical erosion, and long-term climate. The S. Alps have uniform bedrock chemistry but significant tectonic and climatic gradients. West of the main topographic divide, watersheds drain schist and experience high runoff, uplift, and erosion rates. East of the main divide, watersheds drain greywacke or schist and experience lower runoff, uplift, and erosion rates. Glaciated watersheds with high erosion rates are present throughout the mountain range. Both schist and greywacke contain up to 3% metamorphic and hydrothermal calcite. Waters exhibit two-component mixing between calcite and silicate end-members when plotted as δ44Ca versus Ca/Sr. Scatter about the mixing curve is generally smaller than the analytical uncertainty of the measurements and likely reflects variability of the end-member compositions rather than fractionation. We used the mixing relationships to calculate percentages of Ca from silicate weathering. Rivers draining greywacke average 27.6% of Ca from silicate weathering with glaciated and non-glaciated watersheds yielding 41.8 and 19.5%, respectively. Rivers draining schist average 9.8% with glaciated and non-glaciated watersheds yielding 17.7 and 3.9%, respectively. Although Ca fluxes are larger west of the main divide where erosion and runoff are higher, the percentage of Ca from silicate weathering is smaller. Hence, long-term atmospheric CO2 consumption rates do not increase linearly with mechanical erosion because erosion continuously exposes fresh calcite. For non-glacial watersheds, δ44Ca and traditional Ca/Na mixing models yield similar results. However, a substantial difference exists for glacial watersheds. We think δ44Ca is a more sensitive tracer as the difference likely reflects glacial communition, which facilitates rapid and non-stoichiometric release of Ca ions from freshly cleaved silicate surfaces.¶ This study demonstrates the utility of using δ44Ca to trace silicate versus carbonate sources of riverine Ca. Our findings support previous contentions that much of the riverine Ca flux emanating from active orogens originates from carbonate weathering, which is not a sink for atmospheric CO2 over geologic timescales. However, our findings also reveal that silicate weathering and atmospheric CO2 consumption rates in glaciated watersheds are higher than previously realized.

The link between volcanism and plutonism in epizonal magma systems; high-precision U–Pb zircon geochronology from the Organ Mountains caldera and batholith, New Mexico

USGS Publications Warehouse

Rioux, Matthew; Farmer, Lang; Bowring, Samuel; Wooton, Kathleen M.; Amato, Jeffrey M.; Coleman, Drew S.; Verplanck, Philip L.

2016-01-01

The Organ Mountains caldera and batholith expose the volcanic and epizonal plutonic record of an Eocene caldera complex. The caldera and batholith are well exposed, and extensive previous mapping and geochemical analyses have suggested a clear link between the volcanic and plutonic sections, making this an ideal location to study magmatic processes associated with caldera volcanism. Here we present high-precision thermal ionization mass spectrometry U–Pb zircon dates from throughout the caldera and batholith, and use these dates to test and improve existing petrogenetic models. The new dates indicate that Eocene volcanic and plutonic rocks in the Organ Mountains formed from ~44 to 34 Ma. The three largest caldera-related tuff units yielded weighted mean 206Pb/238U dates of 36.441 ± 0.020 Ma (Cueva Tuff), 36.259 ± 0.016 Ma (Achenback Park tuff), and 36.215 ± 0.016 Ma (Squaw Mountain tuff). An alkali feldspar granite, which is chemically similar to the erupted tuffs, yielded a synchronous weighted mean 206Pb/238U date of 36.259 ± 0.021 Ma. Weighted mean 206Pb/238U dates from the larger volume syenitic phase of the underlying Organ Needle pluton range from 36.130 ± 0.031 to 36.071 ± 0.012 Ma, and the youngest sample is 144 ± 20 to 188 ± 20 ka younger than the Squaw Mountain and Achenback Park tuffs, respectively. Younger plutonism in the batholith continued through at least 34.051 ± 0.029 Ma. We propose that the Achenback Park tuff, Squaw Mountain tuff, alkali feldspar granite and Organ Needle pluton formed from a single, long-lived magma chamber/mush zone. Early silicic magmas generated by partial melting of the lower crust rose to form an epizonal magma chamber. Underplating of the resulting mush zone led to partial melting and generation of a high-silica alkali feldspar granite cap, which erupted to form the tuffs. The deeper parts of the chamber underwent continued recharge and crystallization for 144 ± 20 ka after the final eruption. Calculated magmatic fluxes for the Organ Needle pluton range from 0.0006 to 0.0030 km3/year, in agreement with estimates from other well-studied plutons. The petrogenetic evolution proposed here may be common to many small-volume silicic volcanic systems.

Accurate predictions of iron redox state in silicate glasses: A multivariate approach using X-ray absorption spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dyar, M. Darby; McCanta, Molly; Breves, Elly

2016-03-01

Pre-edge features in the K absorption edge of X-ray absorption spectra are commonly used to predict Fe3+ valence state in silicate glasses. However, this study shows that using the entire spectral region from the pre-edge into the extended X-ray absorption fine-structure region provides more accurate results when combined with multivariate analysis techniques. The least absolute shrinkage and selection operator (lasso) regression technique yields %Fe3+ values that are accurate to ±3.6% absolute when the full spectral region is employed. This method can be used across a broad range of glass compositions, is easily automated, and is demonstrated to yield accurate resultsmore » from different synchrotrons. It will enable future studies involving X-ray mapping of redox gradients on standard thin sections at 1 × 1 μm pixel sizes.« less

Accurate predictions of iron redox state in silicate glasses: A multivariate approach using X-ray absorption spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dyar, M. Darby; McCanta, Molly; Breves, Elly

2016-03-01

Pre-edge features in the K absorption edge of X-ray absorption spectra are commonly used to predict Fe 3+ valence state in silicate glasses. However, this study shows that using the entire spectral region from the pre-edge into the extended X-ray absorption fine-structure region provides more accurate results when combined with multivariate analysis techniques. The least absolute shrinkage and selection operator (lasso) regression technique yields %Fe 3+ values that are accurate to ±3.6% absolute when the full spectral region is employed. This method can be used across a broad range of glass compositions, is easily automated, and is demonstrated to yieldmore » accurate results from different synchrotrons. It will enable future studies involving X-ray mapping of redox gradients on standard thin sections at 1 × 1 μm pixel sizes.« less

USING IMAGE PROCESSING METHODS WITH RASTER EDITING TOOLS FOR MAPPING EELGRASS DISTRIBUTIONS IN PACIFIC NORHWEST ESTUARIES

EPA Science Inventory

False-color near-infrared (CIR) aerial photography of seven Oregon estuaries was acquired at extreme low tides and digitally orthorectified with a ground pixel resolution of 25 cm to provide data for intertidal vegetation mapping. Exposed, semi-exposed and some submerged eelgras...

A HYBRID HIGH RESOLUTION IMAGE CLASSIFICATION METHOD FOR MAPPING EELGRASS DISTRIBUTIONS IN YAQUINA BAY ESTUARY, OREGON

EPA Science Inventory

False-color infrared aerial photography of the Yaquina Bay Estuary, Oregon was acquired at extreme low tides and digitally orthorectified with a ground pixel resolution of 20 cm to provide data for intertidal vegetation mapping. Submerged, semi-exposed and exposed eelgrass mead...

The largest volcanic eruptions on Earth

NASA Astrophysics Data System (ADS)

Bryan, Scott E.; Peate, Ingrid Ukstins; Peate, David W.; Self, Stephen; Jerram, Dougal A.; Mawby, Michael R.; Marsh, J. S. (Goonie); Miller, Jodie A.

2010-10-01

Large igneous provinces (LIPs) are sites of the most frequently recurring, largest volume basaltic and silicic eruptions in Earth history. These large-volume (> 1000 km 3 dense rock equivalent) and large-magnitude (> M8) eruptions produce areally extensive (10 4-10 5 km 2) basaltic lava flow fields and silicic ignimbrites that are the main building blocks of LIPs. Available information on the largest eruptive units are primarily from the Columbia River and Deccan provinces for the dimensions of flood basalt eruptions, and the Paraná-Etendeka and Afro-Arabian provinces for the silicic ignimbrite eruptions. In addition, three large-volume (675-2000 km 3) silicic lava flows have also been mapped out in the Proterozoic Gawler Range province (Australia), an interpreted LIP remnant. Magma volumes of > 1000 km 3 have also been emplaced as high-level basaltic and rhyolitic sills in LIPs. The data sets indicate comparable eruption magnitudes between the basaltic and silicic eruptions, but due to considerable volumes residing as co-ignimbrite ash deposits, the current volume constraints for the silicic ignimbrite eruptions may be considerably underestimated. Magma composition thus appears to be no barrier to the volume of magma emitted during an individual eruption. Despite this general similarity in magnitude, flood basaltic and silicic eruptions are very different in terms of eruption style, duration, intensity, vent configuration, and emplacement style. Flood basaltic eruptions are dominantly effusive and Hawaiian-Strombolian in style, with magma discharge rates of ~ 10 6-10 8 kg s -1 and eruption durations estimated at years to tens of years that emplace dominantly compound pahoehoe lava flow fields. Effusive and fissural eruptions have also emplaced some large-volume silicic lavas, but discharge rates are unknown, and may be up to an order of magnitude greater than those of flood basalt lava eruptions for emplacement to be on realistic time scales (< 10 years). Most silicic eruptions, however, are moderately to highly explosive, producing co-current pyroclastic fountains (rarely Plinian) with discharge rates of 10 9-10 11 kg s -1 that emplace welded to rheomorphic ignimbrites. At present, durations for the large-magnitude silicic eruptions are unconstrained; at discharge rates of 10 9 kg s -1, equivalent to the peak of the 1991 Mt Pinatubo eruption, the largest silicic eruptions would take many months to evacuate > 5000 km 3 of magma. The generally simple deposit structure is more suggestive of short-duration (hours to days) and high intensity (~ 10 11 kg s -1) eruptions, perhaps with hiatuses in some cases. These extreme discharge rates would be facilitated by multiple point, fissure and/or ring fracture venting of magma. Eruption frequencies are much elevated for large-magnitude eruptions of both magma types during LIP-forming episodes. However, in basalt-dominated provinces (continental and ocean basin flood basalt provinces, oceanic plateaus, volcanic rifted margins), large magnitude (> M8) basaltic eruptions have much shorter recurrence intervals of 10 3-10 4 years, whereas similar magnitude silicic eruptions may have recurrence intervals of up to 10 5 years. The Paraná-Etendeka province was the site of at least nine > M8 silicic eruptions over an ~ 1 Myr period at ~ 132 Ma; a similar eruption frequency, although with a fewer number of silicic eruptions is also observed for the Afro-Arabian Province. The huge volumes of basaltic and silicic magma erupted in quick succession during LIP events raises several unresolved issues in terms of locus of magma generation and storage (if any) in the crust prior to eruption, and paths and rates of ascent from magma reservoirs to the surface. Available data indicate four end-member magma petrogenetic pathways in LIPs: 1) flood basalt magmas with primitive, mantle-dominated geochemical signatures (often high-Ti basalt magma types) that were either transferred directly from melting regions in the upper mantle to fissure vents at surface, or resided temporarily in reservoirs in the upper mantle or in mafic underplate thereby preventing extensive crustal contamination or crystallisation; 2) flood basalt magmas (often low-Ti types) that have undergone storage at lower ± upper crustal depths resulting in crustal assimilation, crystallisation, and degassing; 3) generation of high-temperature anhydrous, crystal-poor silicic magmas (e.g., Paraná-Etendeka quartz latites) by large-scale AFC processes involving lower crustal granulite melting and/or basaltic underplate remelting; and 4) rejuvenation of upper-crustal batholiths (mainly near-solidus crystal mush) by shallow intrusion and underplating by mafic magma providing thermal and volatile input to produce large volumes of crystal-rich (30-50%) dacitic to rhyolitic magma and for ignimbrite-producing eruptions, well-defined calderas up to 80 km diameter (e.g., Fish Canyon Tuff model), and which characterise of some silicic eruptions in silicic LIPs.

Thermal infrared spectral character of Hawaiian basaltic glasses

NASA Technical Reports Server (NTRS)

Crisp, Joy; Kahle, Anne B.; Abbott, Elsa A.

1990-01-01

Thermal IR reflectance spectra of exposed surfaces of Hawaiian basalt samples from Mauna Loa and Kilauea show systematic changes with age. Spectra of fresh glass collected from active lava flows showed evidence of a strong degree of disorder. After a few weeks of exposure to the laboratory environment, spectra of the top surfaces of these samples began to exhibit spectral features suggestive of ordering into silicate chainlike ansd sheetlike units. With progressive aging, features of apparent sheetlike structures became the preferred mode.

Regional Geological Mapping in the Graham Land of Antarctic Peninsula Using LANDSAT-8 Remote Sensing Data

NASA Astrophysics Data System (ADS)

Pour, A. B.; Hashim, M.; Park, Y.

2017-10-01

Geological investigations in Antarctica confront many difficulties due to its remoteness and extreme environmental conditions. In this study, the applications of Landsat-8 data were investigated to extract geological information for lithological and alteration mineral mapping in poorly exposed lithologies in inaccessible domains such in Antarctica. The north-eastern Graham Land, Antarctic Peninsula (AP) was selected in this study to conduct a satellite-based remote sensing mapping technique. Continuum Removal (CR) spectral mapping tool and Independent Components Analysis (ICA) were applied to Landsat-8 spectral bands to map poorly exposed lithologies at regional scale. Pixels composed of distinctive absorption features of alteration mineral assemblages associated with poorly exposed lithological units were detected by applying CR mapping tool to VNIR and SWIR bands of Landsat-8.Pixels related to Si-O bond emission minima features were identified using CR mapping tool to TIR bands in poorly mapped andunmapped zones in north-eastern Graham Land at regional scale. Anomaly pixels in the ICA image maps related to spectral featuresof Al-O-H, Fe, Mg-O-H and CO3 groups and well-constrained lithological attributions from felsic to mafic rocks were detectedusing VNIR, SWIR and TIR datasets of Landsat-8. The approach used in this study performed very well for lithological andalteration mineral mapping with little available geological data or without prior information of the study region.

The presence of carbonates on Mars: origin, terrestrial analogues and analytical tecniques ambiguity

NASA Astrophysics Data System (ADS)

Marinangeli, Lucia; Liberi, Francesca; Pompilio, Loredana; Piluso, Eugenio; Rosatelli, Gianluigi; Tranquilli, Andrea; Pepe, Monica

2013-04-01

The most common cause of carbonates formation on Earth is the chemical deposition from Ca-rich waters in sedimentary basins, mostly in shallow water. The lack of widespread exposure of carbonates on the Mars' surface in areas where geomorphological and sedimentological mapping confirms the presence of water for a long period of the Martian history, led us to look for a potential different origin of the carbonates identified on CRISM data [1, 2,3]. We suggest the presence of carbonatites on Mars and we have also investigated the capabilities of analytical tecniques for mineralogical analysis to recognise these peculiar type of rocks. Carbonatites are igneous rocks containing more than 50 percent of carbonate minerals and associated silicate minerals as olivine, pyroxene and phyllosilicates. Carbonatites are associated with alkali silicate rocks that are usually of nephelinitic or melilititic affinity. The Martian carbonates are often present in layered rocks and in association with hydrated Fe-Mg silicates (clays family) and kaolinite-group minerals at places [1]. This mineralogical association is very similar to an water-altered carbonatite. We have compared the compositional and mineralogical affinity of some carbonatite samples from different alkaline-carbonatite complexes from Uganda, Spain and Italy, with the mineralogy described for the carbonate- and phyllosolicate rich rocks on Mars, using the XRD and IR analyses. The mineral assemblage has been defined through petrographic analyses as well. It is important to stress that only with XRD analysis some minerals diagnos-tic of carbonatitic assemblage (i.e. melilite) were identified. The relationships between carbonatites and their associated silicate rocks are complex and are still not fully understood on Earth as well, however, it deserves further investigations to better explain the carbonates and silicate volcanic rocks on Mars and its crustal dynamics. References: [1] Michalski and Niles, 2010, Nature Geoscience, 751-755. [2] Helmann et al., 2008, Science, 322, 1828-1832. [3] Morris et al., 2010, Science, 329, 421-424.

The geology of the Inconsolable Range, east-central Sierra Nevada, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hathaway, G.M; Reed, W.E.

1993-04-01

Detailed mapping of the Inconsolable Range in the east-central Sierra Nevada reveals a structurally and lithologically complex region of multi-phase intrusions. Some plutons are compositionally-zoned [e.g., Inconsolable (100 Ma) and Lamarck (90 Ma)]; others may be the result of magma mixing. Intrusive borders vary from brittle to ductile and sharp to gradational, and are bounded by contact aureoles of varying metamorphic grade. A shear zone (Long Lake shear zone -- LLSZ) bounds the western margin of the Inconsolable Range for 8 km; this is truncated in the south by the Cretaceous Lamarck intrusive suite, and is tectonically overlain in themore » north by the Bishop Creek Pendant (Ordovician ). The LLSZ is a complex zone of interleaved septa of biotite schists, orthogneisses, aplitic screens, and calc-silicate gneisses approximately 500 to 800 m wide. Preliminary interpretation suggests that the LLSZ is the sheared remnant of a Triassic-Jurassic igneous terrane complete with metasedimentary pendants. Juxtaposition of greenschist facies meta-sedimentary rocks of the Chocolate Peak klippe over highly deformed amphibolite grade meta-igneous rocks of the LLSZ postdates movement along the LLSZ. Metamorphic grades suggest that deeper structural levels are exposed within the LLSZ near its southern terminus. Twenty plutonic lithologies have been mapped and informally named (e.g., Spotted biotite quartz diorite), including 3 compositionally-zoned plutons. Zonation within the Lamarck, Inconsolable, and Spotted intrusions are the result of multiple emplacement events into partially crystallized host plutons. Along the eastern border of the Lamarck intrusive suite field evidence indicates four separate intrusive events. The Inconsolable body is a compositionally-zoned biotite, clinopyroxene, quartz diorite with irregular granodiorite margins. The base of the Spotted intrusion appears to have been magmatically eroded by a pulse of the younger Lamarck intrusion.« less

Evaluation of thermal control coatings for use on solar dynamic radiators in low earth orbit

NASA Technical Reports Server (NTRS)

Dever, Joyce A.; Rodriguez, Elvin; Slemp, Wayne S.; Stoyack, Joseph E.

1991-01-01

Thermal control coatings with high thermal emittance and low solar absorptance are needed for Space Station Freedom (SSF) solar dynamic power module radiator (SDR) surfaces for efficient heat rejection. Additionally, these coatings must be durable to low earth orbital (LEO) environmental effects of atomic oxygen, ultraviolet radiation and deep thermal cycles which occur as a result of start-up and shut-down of the solar dynamic power system. Eleven candidate coatings were characterized for their solar absorptance and emittance before and after exposure to ultraviolet (UV) radiation (200 to 400 nm), vacuum UV (VUV) radiation (100 to 200 nm) and atomic oxygen. Results indicated that the most durable and best performing coatings were white paint thermal control coatings Z-93, zinc oxide pigment in potassium silicate binder, and YB-71, zinc orthotitanate pigment in potassium silicate binder. Optical micrographs of these materials exposed to the individual environmental effects of atomic oxygen and vacuum thermal cycling showed that no surface cracking occurred.

Cell-based composite materials with programmed structures and functions

DOEpatents

None

2016-03-01

The present invention is directed to the use of silicic acid to transform biological materials, including cellular architecture into inorganic materials to provide biocomposites (nanomaterials) with stabilized structure and function. In the present invention, there has been discovered a means to stabilize the structure and function of biological materials, including cells, biomolecules, peptides, proteins (especially including enzymes), lipids, lipid vesicles, polysaccharides, cytoskeletal filaments, tissue and organs with silicic acid such that these materials may be used as biocomposites. In many instances, these materials retain their original biological activity and may be used in harsh conditions which would otherwise destroy the integrity of the biological material. In certain instances, these biomaterials may be storage stable for long periods of time and reconstituted after storage to return the biological material back to its original form. In addition, by exposing an entire cell to form CSCs, the CSCs may function to provide a unique system to study enzymes or a cascade of enzymes which are otherwise unavailable.

Cell-based composite materials with programmed structures and functions

DOEpatents

Kaehr, Bryan J.; Brinker, C. Jeffrey; Townson, Jason L.

2018-05-15

The present invention is directed to the use of silicic acid to transform biological materials, including cellular architecture into inorganic materials to provide biocomposites (nanomaterials) with stabilized structure and function. In the present invention, there has been discovered a means to stabilize the structure and function of biological materials, including cells, biomolecules, peptides, proteins (especially including enzymes), lipids, lipid vesicles, polysaccharides, cytoskeletal filaments, tissue and organs with silicic acid such that these materials may be used as biocomposites. In many instances, these materials retain their original biological activity and may be used in harsh conditions which would otherwise destroy the integrity of the biological material. In certain instances, these biomaterials may be storage stable for long periods of time and reconstituted after storage to return the biological material back to its original form. In addition, by exposing an entire cell to form CSCs, the CSCs may function to provide a unique system to study enzymes or a cascade of enzymes which are otherwise unavailable.

Sputtering of sodium and potassium from nepheline: Secondary ion yields and velocity spectra

NASA Astrophysics Data System (ADS)

Martinez, R.; Langlinay, Th.; Ponciano, C. R.; da Silveira, E. F.; Palumbo, M. E.; Strazzulla, G.; Brucato, J. R.; Hijazi, H.; Agnihotri, A. N.; Boduch, P.; Cassimi, A.; Domaracka, A.; Ropars, F.; Rothard, H.

2017-09-01

Silicates are the dominant surface material of many Solar System objects, which are exposed to ion bombardment by solar wind ions and cosmic rays. Induced physico-chemical processes include sputtering which can contribute to the formation of an exosphere. We have measured sputtering yields and velocity spectra of secondary ions ejected from nepheline, an aluminosilicate thought to be a good analogue for Mercury's surface, as a laboratory approach to understand the evolution of silicate surfaces and the presence of Na and K vapor in the exosphere. Experiments were performed with highly charged ion beams (keV/u-MeV/u) delivered by GANIL using an imaging XY-TOF-SIMS device under UHV conditions. The fluence dependence of sputtering yields gives information about the evolution of surface stoichiometry during irradiation. From the energy distributions N(E) of sputtered particles, the fraction of particles which could escape from the gravitational field of Mercury, and of those falling back and possibly contributing to populate the exosphere can be roughly estimated.

Evaluation of thermal control coatings for use on solar dynamic radiators in low Earth orbit

NASA Technical Reports Server (NTRS)

Dever, Joyce A.; Rodriguez, Elvin; Slemp, Wayne S.; Stoyack, Joseph E.

1991-01-01

Thermal control coatings with high thermal emittance and low solar absorptance are needed for Space Station Freedom (SSF) solar dynamic power module radiator (SDR) surfaces for efficient heat rejection. Additionally, these coatings must be durable to low earth orbital (LEO) environmental effects of atomic oxygen, ultraviolet radiation and deep thermal cycles which occur as a result of start-up and shut-down of the solar dynamic power system. Eleven candidate coatings were characterized for their solar absorptance and emittance before and after exposure to ultraviolet (UV) radiation (200 to 400 nm), vacuum UV (VUV) radiation (100 to 200 nm) and atomic oxygen. Results indicated that the most durable and best performing coatings were white paint thermal control coatings Z-93, zinc oxide pigment in potassium silicate binder, and YB-71, zinc orthotitanate pigment in potassium silicate binder. Optical micrographs of these materials exposed to the individual environmental effects of atomic oxygen and vacuum thermal cycling showed that no surface cracking occurred.

Oceanic slab melting and mantle metasomatism.

PubMed

Scaillet, B; Prouteau, G

2001-01-01

Modern plate tectonic brings down oceanic crust along subduction zones where it either dehydrates or melts. Those hydrous fluids or melts migrate into the overlying mantle wedge trigerring its melting which produces arc magmas and thus additional continental crust. Nowadays, melting seems to be restricted to cases of young (< 50 Ma) subducted plates. Slab melts are silicic and strongly sodic (trondhjemitic). They are produced at low temperatures (< 1000 degrees C) and under water excess conditions. Their interaction with mantle peridotite produces hydrous metasomatic phases such as amphibole and phlogopite that can be more or less sodium rich. Upon interaction the slab melt becomes less silicic (dacitic to andesitic), and Mg, Ni and Cr richer. Virtually all exposed slab melts display geochemical evidence of ingestion of mantle material. Modern slab melts are thus unlike Archean Trondhjemite-Tonalite-Granodiorite rocks (TTG), which suggests that both types of magmas were generated via different petrogenetic pathways which may imply an Archean tectonic model of crust production different from that of the present-day, subduction-related, one.

Does Silicate Weathering of Loess Affect Atmospheric CO2?

NASA Astrophysics Data System (ADS)

Anderson, S. P.

2002-12-01

Weathering of glacial loess may be a significant, yet unrecognized, component of the carbon cycle. Glaciers produce fine-grained sediment, exposing vast amounts of mineral surface area to weathering processes, yet silicate mineral weathering rates at glacier beds and of glacial till are not high. Thus, despite the tremendous potential for glaciers to influence global weathering rates and atmospheric CO2 levels, this effect has not been demonstrated. Loess, comprised of silt-clay sizes, may be the key glacial deposit in which silicate weathering rates are high. Loess is transported by wind off braid plains of rivers, and deposited broadly (order 100 km from the source) in vegetated areas. Both the fine grain size, and hence large mineral surface area, and presence of vegetation should render loess deposits highly susceptible to silicate weathering. These deposits effectively extend the geochemical impact of glaciation in time and space, and bring rock flour into conditions conducive to chemical weathering. A simple 1-d model of silicate weathering fluxes from a soil profile demonstrates the potential of loess deposition to enhance CO2 consumption. At each time step, computed mineral dissolution (using anorthite and field-based rate constants) modifies the size of mineral grains within the soil. In the case of a stable soil surface, this results in a gradual decline in weathering fluxes and CO2 consumption through time, as finer grain sizes dissolve away. Computed weathering fluxes for a typical loess, with an initial mean grain size of 25 μm, are an order of magnitude greater than fluxes from a non-loess soil that differs only in having a mean grain size of 320 μm. High weathering fluxes are maintained through time if loess is continually deposited. Deposition rates as low as 0.01 mm/yr (one loess grain thickness per year) can lead to a doubling of CO2 consumption rates within 5 ka. These results suggest that even modest loess deposition rates can significantly increase CO2 consumption rates due to silicate weathering in soils. Thick loess deposits cover 5-10% of the global land surface, and loess deposits too thin to be included in global inventories cover a much greater area. Loess deposition and weathering over timescales greater than the duration of glaciation must be considered in models of atmospheric CO2 variation.

Osmium mass balance in peridotite and the effects of mantle-derived sulphides on basalt petrogenesis

NASA Astrophysics Data System (ADS)

Harvey, J.; Dale, C. W.; Gannoun, A.; Burton, K. W.

2011-10-01

Analyses of enriched mantle (EM)-basalts, using lithophile element-based isotope systems, have long provided evidence for discrete mantle reservoirs with variable composition. Upon partial melting, the mantle reservoir imparts its isotopic fingerprint upon the partial melt produced. However, it has increasingly been recognised that it may not be simple to delimit these previously well-defined mantle reservoirs; the "mantle zoo" may contain more reservoirs than previously envisaged. Here we demonstrate that a simple model with varying contributions from two populations of compositionally distinct mantle sulphides can readily account for the observed heterogeneities in Os isotope systematics of such basalts without additional mantle reservoirs. Osmium elemental and isotopic analyses of individual sulphide grains separated from spinel lherzolites from Kilbourne Hole, New Mexico, USA demonstrate that two discrete populations of mantle sulphide exist in terms of both Re-Os systematics and textural relationship with co-existing silicates. One population, with a rounded morphology, is preserved in silicate grains and typically possesses high [Os] and low [Re] with unradiogenic, typically sub-chondritic 187Os/ 188Os attributable to long term isolation in a low-Re environment. By contrast, irregular-shaped sulphides, preserved along silicate grain boundaries, possess low [Os], higher [Re] and a wider range of, but generally supra-chondritic 187Os/ 188Os ([Os] typically ⩽ 1-2 ppm, 187Os/ 188Os ⩽ 0.3729; this study). This population is thought to represent metasomatic sulphide. Uncontaminated silicate phases contain negligible Os (<100 ppt) therefore the Os elemental and isotope composition of basalts is dominated by volumetrically insignificant sulphide ([Os] ⩽ 37 ppm; this study). During the early stages of partial melting, supra-chondritic interstitial sulphides are mobilised and incorporated into the melt, adding their radiogenic 187Os/ 188Os signature. Only when sulphides armoured within silicates are exposed to the melt through continued partial melting will enclosed sulphides add their high [Os] and unradiogenic 187Os/ 188Os to the aggregate melt. Platinum-group element data for whole rocks are also consistent with this scenario. The sequence of (i) addition of all of the metasomatic sulphide, followed by (ii) the incorporation of small amounts of armoured sulphide can thus account for the range of both [Os] and 187Os/ 188Os of EM-basalts worldwide without the need for contributions from additional silicate mantle reservoirs.

Mapping Glauconite Unites with Using Remote Sensing Techniques in North East of Iran

NASA Astrophysics Data System (ADS)

Ahmadirouhani, R.; Samiee, S.

2014-10-01

Glauconite is a greenish ferric-iron silicate mineral with micaceous structure, characteristically formed in shallow marine environments. Glauconite has been used as a pigmentation agent for oil paint, contaminants remover in environmental studies and a source of potassium in plant fertilizers, and other industries. Koppeh-dagh basin is extended in Iran, Afghanistan and Turkmenistan countries and Glauconite units exist in this basin. In this research for enhancing and mapping glauconitic units in Koppeh-dagh structural zone in north east of Iran, remote sensing techniques such as Spectral Angle Mapper classification (SAM), band ratio and band composition methods on SPOT, ASTER and Landsat data in 3 steps were applied.

Final Stages of the 1:24,000-Scale Geologic Mapping of Basin Deposits Exposed in Hadriacus Cavi, Mars

NASA Astrophysics Data System (ADS)

Skinner, J. A.; Fortezzo, C. M.

2018-06-01

This abstract presents a brief summary of the surface and section characteristics of a type area for stratified deposits exposed in Hadriacus Cavi (78.0°E, –27.3°N), Mars based on 1:24,000 scale geologic mapping and stratigraphic analyses.

The Effect of Mycobacterium avium Complex Infections on Routine Mycobacterium bovis Diagnostic Tests

PubMed Central

Barry, Claire; Corbett, David; Bakker, Douwe; Andersen, Peter; McNair, Jim; Strain, Sam

2011-01-01

Bovine tuberculosis (bTB) is diagnosed in naturally infected populations exposed to a wide variety of other pathogens. This study describes the cell-mediated immune responses of cattle exposed to Mycobacterium avium subspecies paratuberculosis (Map) and Mycobacterium avium subspecies avium with particular reference to routine antefmortem Mycobacterium bovis diagnostic tests. The IFN-γ released in response to stimulated blood was found to peak later in the Map-exposed group and was more sustained when compared to the Maa-exposed group. There was a very close correlation between the responses to the purified protein derivatives (PPD) used for stimulation (PPDa, PPDb, and PPDj) with PPDa and PPDj most closely correlated. On occasion, in the Map-infected cattle, PPDb-biased responses were seen compared to PPDa suggesting that some Map-infected cattle could be misclassified as M. bovis infected using this test with these reagents. This bias was not seen when PPDj was used. SICCT results were consistent with the respective infections and all calves would have been classed skin test negative. PMID:21772961

Thermal Residual Stress in Environmental Barrier Coated Silicon Nitride - Modeled

NASA Technical Reports Server (NTRS)

Ali, Abdul-Aziz; Bhatt, Ramakrishna T.

2009-01-01

When exposed to combustion environments containing moisture both un-reinforced and fiber reinforced silicon based ceramic materials tend to undergo surface recession. To avoid surface recession environmental barrier coating systems are required. However, due to differences in the elastic and thermal properties of the substrate and the environmental barrier coating, thermal residual stresses can be generated in the coated substrate. Depending on their magnitude and nature thermal residual stresses can have significant influence on the strength and fracture behavior of coated substrates. To determine the maximum residual stresses developed during deposition of the coatings, a finite element model (FEM) was developed. Using this model, the thermal residual stresses were predicted in silicon nitride substrates coated with three environmental coating systems namely barium strontium aluminum silicate (BSAS), rare earth mono silicate (REMS) and earth mono di-silicate (REDS). A parametric study was also conducted to determine the influence of coating layer thickness and material parameters on thermal residual stress. Results indicate that z-direction stresses in all three systems are small and negligible, but maximum in-plane stresses can be significant depending on the composition of the constituent layer and the distance from the substrate. The BSAS and REDS systems show much lower thermal residual stresses than REMS system. Parametric analysis indicates that in each system, the thermal residual stresses can be decreased with decreasing the modulus and thickness of the coating.

Hydrated mineral stratigraphy of Ius Chasma, Valles Marineris

USGS Publications Warehouse

Roach, L.H.; Mustard, J.F.; Swayze, G.; Milliken, R.E.; Bishop, J.L.; Murchie, S.L.; Lichtenberg, K.

2010-01-01

New high-resolution spectral and morphologic imaging of deposits on walls and floor of Ius Chasma extend previous geomorphic mapping, and permit a new interpretation of aqueous processes that occurred during the development of Valles Marineris. We identify hydrated mineralogy based on visible-near infrared (VNIR) absorptions. We map the extents of these units with CRISM spectral data as well as morphologies in CTX and HiRISE imagery. Three cross-sections across Ius Chasma illustrate the interpreted mineral stratigraphy. Multiple episodes formed and transported hydrated minerals within Ius Chasma. Polyhydrated sulfate and kieserite are found within a closed basin at the lowest elevations in the chasma. They may have been precipitates in a closed basin or diagenetically altered after deposition. Fluvial or aeolian processes then deposited layered Fe/Mg smectite and hydrated silicate on the chasma floor, postdating the sulfates. The smectite apparently was weathered out of Noachian-age wallrock and transported to the depositional sites. The overlying hydrated silicate is interpreted to be an acid-leached phyllosilicate transformed from the underlying smectite unit, or a smectite/jarosite mixture. The finely layered smectite and massive hydrated silicate units have an erosional unconformity between them, that marks a change in surface water chemistry. Landslides transported large blocks of wallrock, some altered to contain Fe/Mg smectite, to the chasma floor. After the last episode of normal faulting and subsequent landslides, opal was transported short distances into the chasma from a few m-thick light-toned layer near the top of the wallrock, by sapping channels in Louros Valles. Alternatively, the material was transported into the chasma and then altered to opal. The superposition of different types of hydrated minerals and the different fluvial morphologies of the units containing them indicate sequential, distinct aqueous environments, characterized by alkaline, then circum-neutral, and finally very acidic surface or groundwater chemistry. ?? 2009 Elsevier Inc. All rights reserved.

Factors that Influence Fast Mapping in Children Exposed to Spanish and English

ERIC Educational Resources Information Center

Alt, Mary; Meyers, Christina; Figueroa, Cecilia

2013-01-01

Purpose: The purpose of this study was to determine whether children exposed to 2 languages would benefit from the phonotactic probability cues of a single language in the same way as monolingual peers and to determine whether crosslinguistic influence would be present in a fast-mapping task. Method: Two groups of typically developing children…

Constituent elements and their distribution in the radioactive Cs-bearing silicate glass microparticles released from Fukushima nuclear plant.

PubMed

Kogure, Toshihiro; Yamaguchi, Noriko; Segawa, Hiroyo; Mukai, Hiroki; Motai, Satoko; Akiyama-Hasegawa, Kotone; Mitome, Masanori; Hara, Toru; Yaita, Tsuyoshi

2016-10-01

Microparticles of radioactive cesium (Cs)-bearing silicate glass emitted from the Fukushima Daiichi nuclear power plant were investigated mainly using state-of-the-art energy-dispersive X-ray spectroscopy in scanning transmission electron microscopes. Precise elemental maps of the particles were obtained using double silicon drift detectors with a large collection angle of X-rays, and qualitative elemental analysis was performed using high-resolution X-ray spectroscopy with a microcalorimetry detector. Beside the substantial elements (O, Si, Cl, K, Fe, Zn, Rb, Sn and Cs) as previously reported, Mn and Ba were also common, though their amounts were small. The atomic ratios of the substantial elements were not the same but varied among individual particles. Fe and Zn were relatively homogeneously distributed, whereas the concentration of alkali ions varied radially. Generally, Cs was rich and K and Rb were poor outward of the particles but the degree of such radial dependence was considerably different among the particles. A concentration of Sn on the particle surface was observed. High-resolution imaging indicated the formation of SnO 2 (cassiterite) nanocrystals on the surface. Synthesis of the bulk glass with a similar composition to the microparticles was attempted by quenching the silicate melt from ∼1600°C. However, homogeneous silicate glass like that of the microparticles could not be obtained due to the segregation of nano-spherules rich in Fe and Zn, suggesting that the microparticles were formed in a very specific condition in the nuclear reactor. © The Author 2016. Published by Oxford University Press on behalf of The Japanese Society of Microscopy. All rights reserved.For permissions, please e-mail: journals.permissions@oup.com.

[Integrated use of data bases to map manufacturing processes involving exposure to carcinogens in the Piedmont Region: the example of formaldehyde].

PubMed

Falcone, U; Gilardi, Luisella; Pasqualini, O; Santoro, S; Coffano, Elena

2010-01-01

Exposure to carcinogens is still widespread in working environments. For the purpose of defining priority of interventions, it is necessary to estimate the number and the geographic distribution of workers potentially exposed to carcinogens. It could therefore be useful to test the use of tools and information sources already available in order to map the distribution of exposure to carcinogens. Formaldehyde is suggested as an example of an occupational carcinogen in this study. The study aimed at verifying and investigating the potential of 3 integrated databases: MATline, CAREX, and company databases resulting from occupational accident and disease claims (INAIL), in order to estimate the number of workers exposed to formaldehyde and map their distribution in the Piedmont Region. The list of manufacturing processes involving exposure to formaldehyde was sorted by MIATline; for each process the number of firms and employees were obtained from the INAIL archives. By applying the prevalence of exposed workers obtained with CAREX, an estimate of exposure for each process was determined. A map of the distribution of employees associated with a specific process was produced using ArcView GIS software. It was estimated that more than 13,000 employees are exposed to formaldehyde in the Piedmont Region. The manufacture of furniture was identified as the process with the highest number of workers exposed to formaldehyde (3,130),followed by metal workers (2,301 exposed) and synthetic resin processing (1,391 exposed). The results obtained from the integrated use of databases provide a basis for defining priority of preventive interventions required in the industrial processes involving exposure to carcinogens in the Piedmont Region.

Geologic Map of the Bodie Hills Volcanic Field, California and Nevada: Anatomy of Miocene Cascade Arc Magmatism in the Western Great Basin

NASA Astrophysics Data System (ADS)

John, D. A.; du Bray, E. A.; Blakely, R. J.; Box, S.; Fleck, R. J.; Vikre, P. G.; Rytuba, J. J.; Moring, B. C.

2011-12-01

The Bodie Hills Volcanic Field (BHVF) is a >700 km2, long-lived (~9 Ma) but episodic, Miocene eruptive center in the southern part of the ancestral Cascade magmatic arc. A 1:50,000-scale geologic map based on extensive new mapping, combined with 40Ar/39Ar dates, geochemical data, and detailed gravity and aeromagnetic surveys, defines late Miocene magmatic and hydrothermal evolution of the BHVF and contrasts the subduction-related BHVF with the overlying, post-subduction, bimodal Plio-Pleistocene Aurora Volcanic Field (AVF). Important features of the BHVF include: Eruptions occurred during 3 major eruptive stages: dominantly trachyandesite stratovolcanoes (~14.7 to 12.9 Ma), mixed silicic trachyandesite, dacite, and rhyolite (~11.3 to 9.6 Ma), and dominantly silicic trachyandesite to dacite domes (~9.2 to 8.0 Ma). Small rhyolite domes were emplaced at ~6 Ma. Trachyandesitic stratovolcanoes with extensive debris flow aprons form the outer part of BHVF, whereas silicic trachyandesite to rhyolite domes are more centrally located. Geophysical data suggest that many BHVF volcanoes have shallow plutonic roots that extend to depths ≥1-2 km below the surface, and much of the Bodie Hills may be underlain by low density plutons presumably related to BHVF volcanism. BHVF rocks contain ~50 to 78% SiO2 (though few rocks have <55% SiO2), have high-K calc-alkaline compositions, and have negative Ti-P-Nb-Ta anomalies and high Ba/Nb, Ba/Ta, and La/Nb typical of subduction-related continental margin arcs. BHVF rocks include mafic trachyandesite/basaltic andesite (50%), silicic trachyandesite-dacite (40%), and rhyolite (10%). Approximately circular, polygenetic volcanoes and scarcity of dikes suggest a low differential horizontal stress field during formation of BHVF. Subduction ceased beneath the Bodie Hills at ~10 Ma, but the composition and eruptive style of volcanism continued unchanged for 2 Ma. However, kinematic data for veins and faults in mining districts suggest a change in the stress field from transtensional to extensional approximately coincident with cessation of subduction. The Bodie Hills are flanked to the east, north, and west by sedimentary basins that began to form in the late Miocene (locally >11 Ma). Fine to coarse sedimentary deposits within the BHVF include stream deposits in channels that cut across the hills and were partly filled by ~9.4 Ma Eureka Valley Tuff erupted 20 km to the northwest. Shallow dips and preservation of primary volcanic morphologies indicate only minor post-volcanic extension of the Bodie Hills. Hydrothermal activity alternated with volcanism, forming both large epithermal Au-Ag vein deposits and large areas of strongly altered but weakly mineralized rock. Compared to AVF, BHVF had a higher average eruptive rate, includes more phenocryst-rich lavas, and formed diverse types of volcanoes inferred to be underlain by large plutons. Consequently, the 2 volcanic fields were probably associated with substantially different magmatic processes and formed in different stress regimes.

Further Investigations of the Passive Optical Sample Assembly (POSA) - I Flight Experiment

NASA Technical Reports Server (NTRS)

Finckenor, Miria M.; Kamenetzky, Rachel R.; Vaughn, Jason A.; Mell, Richard; Deshpande, M. S.

2001-01-01

The Passive Optical Sample Assembly-I (POSA-I), part of the Mir Environmental Effects Payload (MEEP), was designed to study the combined effects of contamination, atomic oxygen, ultraviolet radiation, vacuum, then-nal cycling, and other constituents of the space environment on spacecraft materials. The MEEP program is a Phase I International Space Station Risk Mitigation Experiment. Candidate materials for the International Space Station (ISS) were exposed in a specially designed "suitcase" carrier, with identical specimens facing either Mir or space. The payload was attached by EVA to the exterior of the Mir docking module during the STS-76 mission (f'ig. 1). It was removed during the STS-86 mission after an 18-month exposure. During the mission, it received approximately 7 x 1019 atoMS/CM2 atomic oxygen, as calculated by polymer mass loss, and 413 ESH of solar ultraviolet radiation on the Mir-facing side. The side facing away from Mir received significant contaminant deposition, so atomic oxygen fluence has not been reliably determined. The side facing away from Mir received 571 ESH of solar UV. Contamination was observed on both the Mir-facing and space-facing sides of the POSA-I experiment , with a greater amount of deposition on the space facing side than the Mir side. The contamination has been determined to be outgassed silicone photofixed by ultraviolet radiation and converted to silicate by atomic oxygen interaction. Electron spectroscopy for chemical analysis (ESCA) with depth profiling indicated the presence of 26 - 31 nm silicate on the Mir-facing side and 500 - 1000 nm silicate on the space-facing side. The depth profiling also showed that the contaminant layer was uniform, with a small amount of carbon present on the surface and trace amounts of nitrogen, phosphorus, sulfur, and tin. The surface carbon layer is likely due to post-flight exposure in the laboratory and is similar to carbonaceous deposits on control samples. EDAX and FTIR analysis concurred with ESCA for the presence of silicon, oxygen, and carbon. Nearly 400 samples were exposed on POSA-I, which included materials such as thermal control coatings polymeric films, optical materials, and multi-layer insulation blankets. A previous paper discussed the effects of the space environment exposure and contaminant deposition on candidate materials for ISS, including Z93P inorganic thermal control coating, various anodizes, and multi-layer insulation blankets. This paper details the investigation of environmental effects on the remainder of POSA-I samples, particularly the innovative conductive thermal control coatings developed by AZ Technology of Huntsville, AL and HT Research Institute of Chicago, IL. The silicone/silicate contamination had a significant impact on the solar absorptance of white inorganic thermal control coatings on the space-facing side of POSA-I. The effect of contamination on electrical conductivity is discussed. Samples of conductive anodized aluminum developed by Boundary Technologies of Buffalo Grove, IL were also exposed on POSA-I. The effects of the space environment and contaminant deposition on the optical and electrical properties of the conductive anodized aluminum are discussed.

Detection of hydrated silicates in crustal outcrops in the northern plains of Mars.

PubMed

Carter, J; Poulet, F; Bibring, J-P; Murchie, S

2010-06-25

The composition of the ancient martian crust is a key ingredient in deciphering the environment and evolution of early Mars. We present an analysis of the composition of large craters in the martian northern plains based on data from spaceborne imaging spectrometers. Nine of the craters have excavated assemblages of phyllosilicates from ancient, Noachian crust buried beneath the plains' cover. The phyllosilicates are indistinguishable from those exposed in widespread locations in the southern highlands, demonstrating that liquid water once altered both hemispheres of Mars.

Evaluation of hot corrosion behavior of thermal barrier coatings

NASA Technical Reports Server (NTRS)

Hodge, P. E.; Miller, R. A.; Gedwill, M. A.

1980-01-01

Calcium silicate and yttria stabilized zirconia/MCrAlY thermal barrier coating systems on air-cooled specimens were exposed to sodium plus vanadium doped Mach 0.3 combustion gases. Thermal barrier coating endurance was determined to be a strong inverse function of ceramic coating thickness. Coating system durability was increased through the use of higher Cr + Al NiCrAl and CoCrAlY bond coatings. Chemical and electron microprobe analyses supported the predictions of condensate compositions and the determination of their roles in causing spalling of the ceramic coatings.

Map showing structure of the Mississippi Valley Graben in the vicinity of New Madrid, Missouri

USGS Publications Warehouse

Wheeler, Russell L.; Rhea, Susan; Dart, Richard L.

1994-01-01

This is one of a series of five seismotectonic maps of the seismically active New Madrid area in southeast Missouri and adjacent parts of Arkansas, Kentucky, and Tennessee (table 1). We cannot legibly show all the seismotectonic data on a single map, therefore each of the five maps in this series groups a different type of related information. Rhea and others (1994) summarized the background and purpose of the seismotectonic map folio. The different types of data shown on this map are described in table 2. Except for a few exposed faults, all structures shown on the map are in Paleozoic sedimentary rocks of the midcontinent or underlying metamorphic and igneous basement rocks of presumed Precambrian age (Dart, 1992; Muehlberger, 1992). Edge of Mississippi Embayment, as shown on the map, marks the contact between gently dipping, exposed Paleozoic rocks to the northwest (Anderson and others, 1979) and unconformably overlying, flat or gently dipping Mesozoic and Cenozoic strata of the embayment to the southeast.

Insights Into Magma Ascent During Shallow-Level Crustal Shortening From Magnetic Fabrics of the Philipsburg Batholith, SW Montana

NASA Astrophysics Data System (ADS)

Naibert, T. J.; Geissman, J. W.

2007-12-01

Latest Cretaceous development of the Sevier fold and thrust belt in SW Montana overlapped spatially with silicic magmatism. In the fold thrust belt, large volumes of magma were emplaced well east of the main magmatic arc, now exposed as the Idaho Batholith. Hypothesized mechanisms for emplacement of magma within the overthrust belt often involve magma ascent along shallow, west-dipping faults. The ~ 74 Ma (K-Ar method) Philipsburg Batholith is a 122 km2 tabular granodiorite emplaced into deformed Precambrian Belt Supergroup through Cretaceous strata. The Philipsburg Batholith lies in the upper plate of the Georgetown- Princeton Thrust, NW of Anaconda, Montana and cross-cuts two other previously mapped faults. Anisotropy of magnetic susceptibility (AMS) measurements of 122 sites from the Philipsburg Batholith define magnetic foliations and/or lineations to test magma ascent along the Georgetown-Princeton Thrust. AMS fabrics in the Philipsburg Batholith, dominantly defined by magnetite, are generally oblate or triaxial and are typically very consistent at the site level. Preliminary fabric data show subhorizontal foliations across most of the batholith, with steeply dipping foliations near the margins and a minor increase in foliation dip near the inferred fault trace. The hypothesis of magma ascent along fault surfaces will be supported if further data confirm the concentration of relatively steep foliation orientations across the trace of the Georgetown-Princeton thrust.

Feldspathic Rocks and Associated Mineral Phases on Mars: Evidence for Metamorphism?

NASA Astrophysics Data System (ADS)

Sessa, A. M.; Wray, J. J.

2017-12-01

It is widely accepted that the great majority of Martian crust is basaltic, suggesting that magmatic differentiation was not a key contributor to its production. However, remote sensing studies employing thermal emission imaging instruments aboard Mars Global Surveyor and Mars Odyssey, and recent in situ analyses performed by ChemCam onboard Curiosity, have indicated the presence of more silicic, feldspar-rich rocks with minimal mafics. Using the Compact Reconnaissance Imaging Spectrometer for Mars (CRISM), conceivably similar feldspathic rocks have been reported in other locations across the surface, which include: small outcrops located in the lower stratigraphic section of eastern Vallis Marineris; light-toned, polygonally fractured outcrops exposed within flat-floored craters; as well as other erosional or structural exposures (e.g., buttes, massifs, and crater rims). These previously observed occurrences can be classified as either 1) relatively unaltered rock spectrally dominated by feldspar or 2) an altered material in which CRISM detects feldspar in addition to Al, Fe, Mg-phyllosilicates and/or zeolites. Here we report on feldspathic outcrops that differ in their geologic setting from the previously identified occurrences in that they are associated with complex craters. These outcrops are accompanied by mineral phases that are relatively rare on Mars (i.e., analcime and other zeolites, chlorite, prehnite, mica, and carbonate) and may be indicative of hydrothermal or metamorphic processes. In these craters, feldspathic rocks can be found in and around the central uplift, in crater floor deposits, and in the ejecta, with tentative trends in associated mineralogy. These spatial, and mineralogical, relationships will be illustrated by CRISM RGB composite maps overlain on Context Camera imagery for select scenes. We also report new occurrences like those identified by Carter and Poulet (2013), where feldspar and Al-phyllosilicates are the most spectrally dominant phases in isolated ancient crust exposures. The common co-occurrence of these phases, in the absence of any clear indicators of acidic leaching (e.g., alunite or jarosite), is significant because it is consistent with a protolith, prior to alteration, that was devoid of mafic minerals and composed primarily of aluminum silicates.

Ground-based observation of near-Earth asteroids

NASA Technical Reports Server (NTRS)

Gaffey, Michael J.

1992-01-01

An increased ground-based observation program is an essential component of any serious attempt to assess the resource potential of near-Earth asteroids. A vigorous search and characterization program could lead to the discovery and description of about 400 to 500 near-Earth asteroids in the next 20 years. This program, in conjunction with meteorite studies, would provide the data base to ensure that the results of a small number of asteroid-rendezvous and sample-return missions could be extrapolated with confidence into a geological base map of the Aten, Apollo, and Amor asteroids. Ground-based spectral studies of nearly 30 members of the Aten/Apollo/Amor population provide good evidence that this class includes bodies composed of silicates, metal-silicates, and carbonaceous assemblages similar to those found in meteorites. The instruments that are being used or could be used to search for near-Earth asteroids are listed. Techniques useful in characterizing asteroids and the types of information obtainable using these techniques are listed.

FE-SEM, FIB and TEM Study of Surface Deposits of Apollo 15 Green Glass Volcanic Spherules

NASA Technical Reports Server (NTRS)

Ross, Daniel K.; Thomas-Keprta, K. L.; Rahman, Z.; Wentworth, S. J.; McKay, D. S.

2011-01-01

Surface deposits on lunar pyroclastic green (Apollo 15) and orange (Apollo 17) glass spherules have been attributed to condensation from the gas clouds that accompanied fire-fountain eruptions. The fire fountains cast molten lava high above the lunar surface and the silicate melt droplets quenched before landing producing the glass beads. Early investigations showed that these deposits are rich in sulfur and zinc. The deposits are extremely fine-grained and thin, so that it was never possible to determine their chemical compositions cleanly by SEM/EDX or electron probe x-ray analysis because most of the excited volume was in the under-lying silicate glass. We are investigating the surface deposits by TEM, using focused ion beam (FIB) microscopy to extract and thin the surface deposits. Here we report on chemical mapping of a FIB section of surface deposits of an Apollo green glass bead 15401using the ultra-high resolution JEOL 2500 STEM located at NASA Johnson Space Center.

Satellite-derived mineral mapping and monitoring of weathering, deposition and erosion

PubMed Central

Cudahy, Thomas; Caccetta, Mike; Thomas, Matilda; Hewson, Robert; Abrams, Michael; Kato, Masatane; Kashimura, Osamu; Ninomiya, Yoshiki; Yamaguchi, Yasushi; Collings, Simon; Laukamp, Carsten; Ong, Cindy; Lau, Ian; Rodger, Andrew; Chia, Joanne; Warren, Peter; Woodcock, Robert; Fraser, Ryan; Rankine, Terry; Vote, Josh; de Caritat, Patrice; English, Pauline; Meyer, Dave; Doescher, Chris; Fu, Bihong; Shi, Pilong; Mitchell, Ross

2016-01-01

The Earth’s surface comprises minerals diagnostic of weathering, deposition and erosion. The first continental-scale mineral maps generated from an imaging satellite with spectral bands designed to measure clays, quartz and other minerals were released in 2012 for Australia. Here we show how these satellite mineral maps improve our understanding of weathering, erosional and depositional processes in the context of changing weather, climate and tectonics. The clay composition map shows how kaolinite has developed over tectonically stable continental crust in response to deep weathering during northwardly migrating tropical conditions from 45 to 10 Ma. The same clay composition map, in combination with one sensitive to water content, enables the discrimination of illite from montmorillonite clays that typically develop in large depositional environments over thin (sinking) continental crust such as the Lake Eyre Basin. Cutting across these clay patterns are sandy deserts that developed <10 Ma and are well mapped using another satellite product sensitive to the particle size of silicate minerals. This product can also be used to measure temporal gains/losses of surface clay caused by periodic wind erosion (dust) and rainfall inundation (flood) events. The accuracy and information content of these satellite mineral maps are validated using published data. PMID:27025192

Probing the deep critical zone beneath the Luquillo Experimental Forest, Puerto Rico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buss, Heather; Brantley, S. L.; Scatena, Fred

2013-01-01

Recent work has suggested that weathering processes occurring in the subsurface produce the majority of silicate weathering products discharged to the world s oceans, thereby exerting a primary control on global temperature via the well-known positive feedback between silicate weathering and CO2. In addition, chemical and physical weathering processes deep within the critical zone create aquifers and control groundwater chemistry, watershed geometry and regolith formation rates. Despite this, most weathering studies are restricted to the shallow critical zone (e.g., soils, outcrops). Here we investigate the chemical weathering, fracturing and geomorphology of the deep critical zone in the Bisley watershed inmore » the Luquillo Critical Zone Observatory, Puerto Rico, from two boreholes drilled to 37.2 and 27.0 m depth, from which continuous core samples were taken. Corestones exposed aboveground were also sampled. Weathered rinds developed on exposed corestones and along fracture surfaces on subsurface rocks slough off of exposed corestones once rinds attain a thickness up to ~1 cm, preventing the corestones from rounding due to diffusion limitation. Such corestones at the land surface are assumed to be what remains after exhumation of similar, fractured bedrock pieces that were observed in the drilled cores between thick layers of regolith. Some of these subsurface corestones are massive and others are highly fractured, whereas aboveground corestones are generally massive with little to no apparent fracturing. Subsurface corestones are larger and less fractured in the borehole drilled on a road where it crosses a ridge compared to the borehole drilled where the road crosses the stream channel. Both borehole profiles indicate that the weathering zone extends to well below the stream channel in this upland catchment; hence weathering depth is not controlled by the stream level within the catchment and not all of the water in the watershed is discharged to the stream.« less

Evolution of silicic magma in the upper crust: the mid-Tertiary Latir volcanic field and its cogenetic granitic batholith, northern New Mexico, USA

USGS Publications Warehouse

Lipman, P.W.

1988-01-01

Structural and topographic relief along the eastern margin of the Rio Grande rift, northern New Mexico, provides a remarkable cross-section through the 26-Ma Questa caldera and cogenetic volcanic and plutonic rocks of the Latir field. Exposed levels increase in depth from mid-Tertiary depositional surfaces in northern parts of the igneous complex to plutonic rocks originally at 3-5 km depths in the S. Erosional remnants of an ash-flow sheet of weakly peralkaline rhyolite (Amalia Tuff) and andesitic to dactitic precursor lavas, disrupted by rift-related faults, are preserved as far as 45 km beyond their sources at the Questa caldera. Broadly comagmatic 26 Ma batholithic granitic rocks, exposed over an area of 20 by 35 km, range from mesozonal granodiorite to epizonal porphyritic granite and aplite; shallower and more silicic phases are mostly within the caldera. Compositionally and texturally distinct granites defined resurgent intrusions within the caldera and discontinuous ring dikes along its margins: a batholithic mass of granodiorite extends 20 km S of the caldera and locally grades vertically to granite below its flat-lying roof. A negative Bouguer gravity anomaly (15-20 mgal), which encloses exposed granitic rocks and coincides with boundaries of the Questa caldera, defined boundaries of the shallow batholith, emplaced low in the volcanic sequence and in underlying Precambrian rocks. Paleomagnetic pole positions indicate that successively crystallised granitic plutons cooled through Curie temperatures during the time of caldera formation, initial regional extension, and rotational tilting of the volcanic rocks. Isotopic ages for most intrusions are indistinguishable from the volcanic rocks. These relations indicate that the batholithic complex broadly represents the source magma for the volcanic rocks, into which the Questa caldera collapsed, and that the magma was largely liquid during regional tectonic disruption. -from Author

Probing the deep critical zone beneath the Luquillo Experimental Forest, Puerto Rico

USGS Publications Warehouse

Buss, Heather L.; Brantley, Susan L.; Scatena, Fred; Bazilevskaya, Katya; Blum, Alex E.; Schulz, Marjorie S.; Jiménez, Rafael; White, Arthur F.; Rother, G.; Cole, D.

2013-01-01

Recent work has suggested that weathering processes occurring in the subsurface produce the majority of silicate weathering products discharged to the world's oceans, thereby exerting a primary control on global temperature via the well-known positive feedback between silicate weathering and CO2. In addition, chemical and physical weathering processes deep within the critical zone create aquifers and control groundwater chemistry, watershed geometry and regolith formation rates. Despite this, most weathering studies are restricted to the shallow critical zone (e.g. soils, outcrops). Here we investigate the chemical weathering, fracturing and geomorphology of the deep critical zone in the Bisley watershed in the Luquillo Critical Zone Observatory, Puerto Rico, from two boreholes drilled to 37.2 and 27.0 m depth, from which continuous core samples were taken. Corestones exposed aboveground were also sampled. Weathered rinds developed on exposed corestones and along fracture surfaces on subsurface rocks slough off of exposed corestones once rinds attain a thickness up to ~1 cm, preventing the corestones from rounding due to diffusion limitation. Such corestones at the land surface are assumed to be what remains after exhumation of similar, fractured bedrock pieces that were observed in the drilled cores between thick layers of regolith. Some of these subsurface corestones are massive and others are highly fractured, whereas aboveground corestones are generally massive with little to no apparent fracturing. Subsurface corestones are larger and less fractured in the borehole drilled on a road where it crosses a ridge compared with the borehole drilled where the road crosses the stream channel. Both borehole profiles indicate that the weathering zone extends to well below the stream channel in this upland catchment; hence weathering depth is not controlled by the stream level within the catchment and not all of the water in the watershed is discharged to the stream

Mechanical and Microstructural Evaluations of Lightweight Aggregate Geopolymer Concrete before and after Exposed to Elevated Temperatures

PubMed Central

Abdulkareem, Omar A.; Abdullah, Mohd Mustafa Al Bakri; Hussin, Kamarudin; Ismail, Khairul Nizar; Binhussain, Mohammed

2013-01-01

This paper presents the mechanical and microstructural characteristics of a lightweight aggregate geopolymer concrete (LWAGC) synthesized by the alkali-activation of a fly ash source (FA) before and after being exposed to elevated temperatures, ranging from 100 to 800 °C. The results show that the LWAGC unexposed to the elevated temperatures possesses a good strength-to-weight ratio compared with other LWAGCs available in the published literature. The unexposed LWAGC also shows an excellent strength development versus aging times, up to 365 days. For the exposed LWAGC to the elevated temperatures of 100 to 800 °C, the results illustrate that the concretes gain compressive strength after being exposed to elevated temperatures of 100, 200 and 300 °C. Afterward, the strength of the LWAGC started to deteriorate and decrease after being exposed to elevated temperatures of 400 °C, and up to 800 °C. Based on the mechanical strength results of the exposed LWAGCs to elevated temperatures of 100 °C to 800 °C, the relationship between the exposure temperature and the obtained residual compressive strength is statistically analyzed and achieved. In addition, the microstructure investigation of the unexposed LWAGC shows a good bonding between aggregate and mortar at the interface transition zone (ITZ). However, this bonding is subjected to deterioration as the LWAGC is exposed to elevated temperatures of 400, 600 and 800 °C by increasing the microcrack content and swelling of the unreacted silicates. PMID:28788339

Mechanical and Microstructural Evaluations of Lightweight Aggregate Geopolymer Concrete before and after Exposed to Elevated Temperatures.

PubMed

Abdulkareem, Omar A; Abdullah, Mohd Mustafa Al Bakri; Hussin, Kamarudin; Ismail, Khairul Nizar; Binhussain, Mohammed

2013-10-09

This paper presents the mechanical and microstructural characteristics of a lightweight aggregate geopolymer concrete (LWAGC) synthesized by the alkali-activation of a fly ash source (FA) before and after being exposed to elevated temperatures, ranging from 100 to 800 °C. The results show that the LWAGC unexposed to the elevated temperatures possesses a good strength-to-weight ratio compared with other LWAGCs available in the published literature. The unexposed LWAGC also shows an excellent strength development versus aging times, up to 365 days. For the exposed LWAGC to the elevated temperatures of 100 to 800 °C, the results illustrate that the concretes gain compressive strength after being exposed to elevated temperatures of 100, 200 and 300 °C. Afterward, the strength of the LWAGC started to deteriorate and decrease after being exposed to elevated temperatures of 400 °C, and up to 800 °C. Based on the mechanical strength results of the exposed LWAGCs to elevated temperatures of 100 °C to 800 °C, the relationship between the exposure temperature and the obtained residual compressive strength is statistically analyzed and achieved. In addition, the microstructure investigation of the unexposed LWAGC shows a good bonding between aggregate and mortar at the interface transition zone (ITZ). However, this bonding is subjected to deterioration as the LWAGC is exposed to elevated temperatures of 400, 600 and 800 °C by increasing the microcrack content and swelling of the unreacted silicates.

PenMap demonstration project, landslide mapping system

DOT National Transportation Integrated Search

2002-12-01

This report documents the findings of a technology transfer project to demonstrate the effectiveness of a portable field mapping system to landslide field reconnaissance work. The objective of this project was to expose the latest field data collecti...

Organ specific mapping of in vivo redox state in control and cigarette smoke-exposed mice using EPR/NMR co-imaging

PubMed Central

Caia, George L.; Efimova, Olga V.; Velayutham, Murugesan; El-Mahdy, Mohamed A.; Abdelghany, Tamer M.; Kesselring, Eric; Petryakov, Sergey; Sun, Ziqi; Samouilov, Alexandre; Zweier, Jay L.

2014-01-01

In vivo mapping of alterations in redox status is important for understanding organ specific pathology and disease. While electron paramagnetic resonance imaging (EPRI) enables spatial mapping of free radicals, it does not provide anatomic visualization of the body. Proton MRI is well suited to provide anatomical visualization. We applied EPR/NMR co-imaging instrumentation to map and monitor the redox state of living mice under normal or oxidative stress conditions induced by secondhand cigarette smoke (SHS) exposure. A hybrid co-imaging instrument, EPRI (1.2 GHz) / proton MRI (16.18 MHz), suitable for whole-body co-imaging of mice was utilized with common magnet and gradients along with dual EPR/NMR resonators that enable co-imaging without sample movement. The metabolism of the nitroxide probe, 3–carbamoyl–proxyl (3-CP), was used to map the redox state of control and SHS-exposed mice. Co-imaging allowed precise 3D mapping of radical distribution and reduction in major organs such as the heart, lungs, liver, bladder and kidneys. Reductive metabolism was markedly decreased in SHS-exposed mice and EPR/NMR co-imaging allowed quantitative assessment of this throughout the body. Thus, in vivo EPR/NMR co-imaging enables in vivo organ specific mapping of free radical metabolism and redox stress and the alterations that occur in the pathogenesis of disease. PMID:22296801

Organ specific mapping of in vivo redox state in control and cigarette smoke-exposed mice using EPR/NMR co-imaging

NASA Astrophysics Data System (ADS)

Caia, George L.; Efimova, Olga V.; Velayutham, Murugesan; El-Mahdy, Mohamed A.; Abdelghany, Tamer M.; Kesselring, Eric; Petryakov, Sergey; Sun, Ziqi; Samouilov, Alexandre; Zweier, Jay L.

2012-03-01

In vivo mapping of alterations in redox status is important for understanding organ specific pathology and disease. While electron paramagnetic resonance imaging (EPRI) enables spatial mapping of free radicals, it does not provide anatomic visualization of the body. Proton MRI is well suited to provide anatomical visualization. We applied EPR/NMR co-imaging instrumentation to map and monitor the redox state of living mice under normal or oxidative stress conditions induced by secondhand cigarette smoke (SHS) exposure. A hybrid co-imaging instrument, EPRI (1.2 GHz)/proton MRI (16.18 MHz), suitable for whole-body co-imaging of mice was utilized with common magnet and gradients along with dual EPR/NMR resonators that enable co-imaging without sample movement. The metabolism of the nitroxide probe, 3-carbamoyl-proxyl (3-CP), was used to map the redox state of control and SHS-exposed mice. Co-imaging allowed precise 3D mapping of radical distribution and reduction in major organs such as the heart, lungs, liver, bladder and kidneys. Reductive metabolism was markedly decreased in SHS-exposed mice and EPR/NMR co-imaging allowed quantitative assessment of this throughout the body. Thus, in vivo EPR/NMR co-imaging enables in vivo organ specific mapping of free radical metabolism and redox stress and the alterations that occur in the pathogenesis of disease.

The system CaO-MgO-SiO2-CO2 at 1 GPa, metasomatic wehrlites, and primary carbonatite magmas

NASA Astrophysics Data System (ADS)

Lee, W. J.; Wyllie, P. J.

New experimental data in CaO-MgO-SiO2-CO2 at 1GPa define the vapor-saturated silicate-carbonate liquidus field boundary involving primary minerals calcite, forsterite and diopside. The eutectic reaction for melting of model calcite (1% MC)-wehrlite at 1GPa is at 1100°C, with liquid composition (by weight) 72% CaCO3 (CC), 9% MgCO3 (MC), and 18% CaMgSi2O6 (Di). These data combined with previous results permit construction of the isotherm-contoured vapor-saturated liquidus surface for the calcite/dolomite field, and part of the adjacent forsterite and diopside fields. Nearly pure calcite crystals in mantle xenoliths cannot represent equilibrium liquids. We recently determined the complete vapor-saturated liquidus surface between carbonates and model peridotites at 2.7GPa the peritectic reaction for dolomite (25% MC)-wehrlite at 2.7GPa occurs at 1300°C, with liquid composition 60% CC, 29% MC, and 11% Di. The liquidus field boundaries on these two surfaces provide the road-map for interpretation of magmatic processes in various peridotite-CO2 systems at depths between the Moho and about 100km. Relationships among kimberlites, melilitites, carbonatites and the liquidus phase boundaries are discussed. Experimental data for carbonatite liquid protected by metasomatic wehrlite have been reported. The liquid trends directly from dolomitic towards CaCO3 with decreasing pressure. The 1.5GPa liquid contains 87% CC and 4% Di, much lower in silicate components than our phase boundary. However, the liquids contain approximately the same CaCO3 (90+/- 1wt%) in terms of only carbonate components. For CO2-bearing mantle, all magmas at depth must pass through initial dolomitic compositions. Rising dolomitic carbonatite melt will vesiculate and may erupt as primary magmas through cracks from about 70km. If it percolates through metasomatic wehrlite from 70km toward the Moho at 35-40km, primary calcic siliceous carbonatite magma can be generated with silicate content at least 11-18% (70-40km) on the silicate-carbonate boundary.

Effects of Irradiation on Albite's Chemical Durability.

PubMed

Hsiao, Yi-Hsuan; La Plante, Erika Callagon; Krishnan, N M Anoop; Le Pape, Yann; Neithalath, Narayanan; Bauchy, Mathieu; Sant, Gaurav

2017-10-19

Albite (NaAlSi 3 O 8 ), a framework silicate of the plagioclase feldspar family and a common constituent of felsic rocks, is often present in the siliceous mineral aggregates that compose concrete. When exposed to radiation (e.g., in the form of neutrons) in nuclear power plants, the crystal structure of albite can undergo significant alterations. These alterations may degrade its chemical durability. Indeed, careful examinations of Ar + -implanted albite carried out using Fourier transform infrared spectroscopy (FTIR) and molecular dynamics simulations show that albite's crystal structure, upon irradiation, undergoes progressive disordering, resulting in an expansion in its molar volume (i.e., a reduction of density) and a reduction in the connectivity of its atomic network. This loss of network connectivity (i.e., rigidity) results in an enhancement of the aqueous dissolution rate of albite-measured using vertical scanning interferometry (VSI) in alkaline environments-by a factor of 20. This enhancement in the dissolution rate (i.e., reduction in chemical durability) of albite following irradiation has significant impacts on the durability of felsic rocks and of concrete containing them upon their exposure to radiation in nuclear power plant (NPP) environments.

The McDermitt Caldera, NV-OR, USA: Geologic mapping, volcanology, mineralization, and high precision 40Ar/39Ar dating of early Yellowstone hotspot magmatism

NASA Astrophysics Data System (ADS)

Henry, C. D.; Castor, S. B.; Starkel, W. A.; Ellis, B. S.; Wolff, J. A.; Heizler, M. T.; McIntosh, W. C.

2012-12-01

The irregularly keyhole-shaped, 40x30 to 22 km, McDermitt caldera formed at 16.35±0.03 Ma (n=4; Fish Canyon sanidine = 28.201 Ma) during eruption of a zoned, aphyric, mildly peralkaline rhyolite to abundantly anorthoclase-phyric, metaluminous dacite (McDermitt Tuff, MDT). Intracaldera MDT is locally strongly rheomorphic and, where MDT and caldera floor are well-exposed along the western margin, contains abundant megabreccia but is a maximum of ~450 m thick. If this thickness is representative of the caldera, intracaldera MDT has a volume of ~400 km3. Outflow MDT is currently known up to 13 km south of the caldera but only 3 km north of the caldera. Maximum outflow thickness is ~100 m, and outflow volume is probably no more than about 10% that of intracaldera MDT. The thickness and volume relations indicate collapse began very early during eruption, and most tuff ponded within the caldera. Outflow is strongly rheomorphic where draped over paleotopography. Late, undated icelandite lavas and domes are probably residual magma from the caldera chamber. Resurgence is expressed as both a broad, symmetrical dome in the north part and a fault-bound uplift in the south part of the caldera. Mineralization associated with the caldera includes Zr-rich U deposits that are indistinguishable in age with the McDermitt Tuff, Hg, Au, Ga, and Li-rich intracaldera tuffaceous sediments. Although formed during probable regional extension, the caldera is flat-lying and cut only at its west and east margins by much younger, high-angle normal faults. The caldera formed in an area of highly diverse Cenozoic volcanic rocks. The oldest are 39 and 46 Ma metaluminous dacite lavas along the northwest margin. Coarsely plagioclase-phyric to aphyric Steens Basalt lavas crop out around the west, northwest, and northeast margin. An anorthoclase-phyric, low-Si rhyolite lava (16.69±0.02 Ma) that is interbedded with probable Steens lavas northeast of the caldera and a biotite rhyolite lava dome (16.62±0.02 Ma) in the west floor of the caldera are the oldest middle Miocene silicic rocks near the caldera. Other pre-caldera rocks are a mix of variably peralkaline, distal ignimbrites; biotite rhyolite domes and lavas; and variably peralkaline rhyolite lavas that were emplaced between about 16.50 and 16.36 Ma. Silicic volcanism around the McDermitt caldera is some of the oldest of the Yellowstone hotspot track, but two known calderas in NW Nevada and unidentified sources of distal ignimbrites near McDermitt are older than the McDermitt caldera. Initial hotspot silicic volcanism occurred over a large area across NW Nevada, SE Oregon, and SW Idaho.

Stratigraphy of lower to middle Paleozoic rocks of northern Nevada and the Antler orogeny

USGS Publications Warehouse

Ketner, Keith B.

2013-01-01

Commonly accepted concepts concerning the lower Paleozoic stratigraphy of northern Nevada are based on the assumption that the deep-water aspects of Ordovician to Devonian siliceous strata are due to their origin in a distant oceanic environment, and their presence where we find them is due to tectonic emplacement by the Roberts Mountains thrust. The concept adopted here is based on the assumption that their deep-water aspects are the result of sea-level rise in the Cambrian, and all of the Paleozoic strata in northern Nevada are indigenous to that area. The lower part of the Cambrian consists mainly of shallow-water cross-bedded sands derived from the craton. The upper part of the Cambrian, and part of the Ordovician, consists mainly of deep-water carbonate clastics carried by turbidity currents from the carbonate shelf in eastern Nevada, newly constructed as a result of sea-level rise. Ordovician to mid-Devonian strata are relatively deep-water siliceous deposits, which are the western facies assemblage. The basal contact of this assemblage on autochthonous Cambrian rocks is exposed in three mountain ranges and is clearly depositional in all three. The western facies assemblage can be divided into distinct stratigraphic units of regional extent. Many stratigraphic details can be explained simply by known changes in sea level. Upper Devonian to Mississippian strata are locally and westerly derived orogenic clastic beds deposited disconformably on the western facies assemblage. This disconformity, clearly exposed in 10 mountain ranges, indicates regional uplift and erosion of the western facies assemblage and absence of local deformation. The disconformity represents the Antler orogeny.

Handmade Multitextured Maps.

ERIC Educational Resources Information Center

Trevelyan, Simon

1984-01-01

Tactile maps for visually impaired persons can be made by drawing lines with an aqueous adhesive solution, dusting with thermoengraving powder, and exposing the card to a source of intense heat (such as a heat gun or microwave oven). A raised line map results. (CL)

Hot Spots on Io: Initial Results From Galileo's Near Infrared Mapping Spectrometer

NASA Technical Reports Server (NTRS)

Lopes-Gautier, Rosaly; Davies, A. G.; Carlson, R.; Smythe, W.; Kamp, L.; Soderblom, L.; Leader, F. E.; Mehlman, R.

1997-01-01

The Near-Infrared Mapping Spectrometer on Galileo has monitored the volcanic activity on Io since June 28, 1996. This paper presents preliminary analysis of NIMS thermal data for the first four orbits of the Galileo mission. NIMS has detected 18 new hot spots and 12 others which were previously known to be active. The distribution of the hot spots on Io's surface may not be random, as hot spots surround the two bright, SO2-rich regions of Bosphorus Regio and Colchis Regio. Most hot spots scan to be persistently active from orbit to orbit and 10 of those detected were active in 1979 during the Voyager encounters. We report the distribution of hot spot temperatures and find that they are consistent with silicate volcanism.

Mars Surface Diversity as Revealed by the OMEGA/Mars Express Observations

NASA Astrophysics Data System (ADS)

Bibring, Jean-Pierre; Langevin, Yves; Gendrin, Aline; Gondet, Brigitte; Poulet, François; Berthé, Michel; Soufflot, Alain; Arvidson, Ray; Mangold, Nicolas; Mustard, John; Drossart, P.; OMEGA Team; Erard, Stéphane; Forni, Olivier; Combes, Michel; Encrenaz, Thérèse; Fouchet, Thierry; Merchiorri, Riccardo; Belluci, GianCarlo; Altieri, Francesca; Formisano, Vittorio; Bonello, Guillaume; Capaccioni, Fabricio; Cerroni, Pricilla; Coradini, Angioletta; Fonti, Sergio; Kottsov, Volodia; Ignatiev, Nikolai; Moroz, Vassili; Titov, Dimitri; Zasova, Ludmilla; Mangold, Micholas; Pinet, Patrick; Douté, Sylvain; Schmitt, Bernard; Sotin, Christophe; Hauber, Ernst; Hoffmann, Harald; Jaumann, Ralf; Keller, Uwe; Duxbury, Tom; Forget, François

2005-03-01

The Observatoire pour la Minéralogie, l'Eau, les Glaces, et l'Activité (OMEGA) investigation, on board the European Space Agency Mars Express mission, is mapping the surface composition of Mars at a 0.3- to 5-kilometer resolution by means of visible-near-infrared hyperspectral reflectance imagery. The data acquired during the first 9 months of the mission already reveal a diverse and complex surface mineralogy, offering key insights into the evolution of Mars. OMEGA has identified and mapped mafic iron-bearing silicates of both the northern and southern crust, localized concentrations of hydrated phyllosilicates and sulfates but no carbonates, and ices and frosts with a water-ice composition of the north polar perennial cap, as for the south cap, covered by a thin carbon dioxide-ice veneer.

Factors That Influence Fast Mapping in Children Exposed to Spanish and English

PubMed Central

Alt, Mary; Meyers, Christina; Figueroa, Cecilia

2015-01-01

Purpose The purpose of this study was to determine if children exposed to two languages would benefit from the phonotactic probability cues of a single language in the same way as monolingual peers and to determine if cross-linguistic influence would be present in a fast mapping task. Method Two groups of typically-developing children (monolingual English and bilingual Spanish-English) took part in a computer-based fast mapping task which manipulated phonotactic probability. Children were preschool-aged (N = 50) or school-aged (N = 34). Fast mapping was assessed through name identification and naming tasks. Data were analyzed using mixed ANOVAs with post-hoc testing and simple regression. Results Bilingual and monolingual preschoolers showed sensitivity to English phonotactic cues in both tasks, but bilingual preschoolers were less accurate than monolingual peers in the naming task. School-aged bilingual children had nearly identical performance to monolingual peers. Conclusions Knowing that children exposed to two languages can benefit from the statistical cues of a single language can help inform ideas about instruction and assessment for bilingual learners. PMID:23816663

Geology and Conceptual Model of the Domuyo Geothermal Area, Patagonia, Argentina

NASA Astrophysics Data System (ADS)

Fragoso, A. S.; Ferrari, L.; Norini, G.

2017-12-01

Cerro Domuyo is the highest mountain in Patagonia and its western slope is characterized by thermal springs with boiling fluids as well as silicic domes and pyroclastic deposits that suggest the existence of a geothermal reservoir. Early studies proposed that the thermal springs were fault-controlled and the reservoir was located in a graben bounded by E-W normal faults. A recent geochemical study estimated a temperature of 220ºC for the fluid reservoir and a thermal energy release of 1.1 GW, one of the world largest advective heat flux from a continental volcanic center. We carried out a geologic survey and U-Pb and U-Th geochronologic study to elaborate an updated conceptual model for the Domuyo geothermal area. Our study indicates that the Domuyo Volcanic Complex (DVC) is a dome complex overlying an older, Middle Miocene to Pliocene volcanic sequence widely exposed to the southwest and to the north, which in turn covers: 1) the Jurassice-Early Creteacoeus Neuquen marine sedimentary succession, 2) silicic ignimbrites dated at 186.7 Ma and, 3) the Paleozoic metamorphic basement intruded by 288 Ma granite bodies. These pre-Cenozoic successions are involved in dominantly N-S trending folds and thrust faults later displaced by E-W striking normal faults with a right lateral component of motion that underlie the DVC. The volcanic cycle forming the DVC is distinctly bimodal with the emplacement of massive silicic domes but also less voluminous olivine basalts on its southern slope. The central dome underwent a major collapse that produced 0.35 km3 of ash and block flow and associated pyroclastic flows that filled the valley to the southwest up to 30 km from the source. This was followed by a voluminous effusive activity that formed silicic domes dated between 254-322 Ky, which is inferred to overlain a partially molten silicic magma chamber. Integrating the geologic model with magnetotelluric and gravity surveys we developed a conceptual model of the geothermal system in which the reservoir is inferred at a depth of less than 2 km in pre-Pliocene fractured rocks, bounded by E-W faults and sealed by the pyroclastic deposits and rhyolitic lavas of the DVC. The location of most thermal springs is not controlled by faults. Rather, they are lateral flows emerging at the contact between the fractured basement and the caprock.

Reconstructing the Jurassic Talkeetna Intra-oceanic Arc of Alaska Using Thermobarometry

NASA Astrophysics Data System (ADS)

Hacker, B. R.; Mehl, L.; Kelemen, P. B.; Rioux, M.; Greene, A.

2005-12-01

The Talkeetna arc is one of two intra-oceanic arcs where the entire section from the upper mantle tectonite through the sediments capping the volcanic carapace is well exposed. The objective of this study is to reconstruct the vertical section of the Talkeetna arc by determining the (re) crystallization pressures at various structural levels. This information is crucial if the Talkeetna arc is to be exploited as an archetypal cross section for purposes as diverse as understanding the evolution of the Earth's crust, assessing rates and mechanisms of arc growth, and understanding the tectonic history arcs in general. The base of the arc crust exposed at Bernard and Scarp Mtns includes rare gabbro(norites) with metamorphic garnets-mineral assemblages excellent for thermobarometry. Broad core-to-rim garnet zoning toward lower Mg#, pyroxenes with near-rim, steep increases in Mg# and Al2O3, and unzoned plagioclase document cooling following core crystallization at ~900- 1025 °C and 0.9-1.0 GPa. Hornblende gabbros with magmatic garnet exposed in the Klanelneechena klippe indicate significantly lower P-T of ~700-835°C, 0.69- 0.77 GPa. Hornblende gabbro (norites) that comprise the bulk of the arc were studied in the Tazlina, Barnette, Scarp, and Pippin Ridge sections. Differences in mineral composition indicate qualitatively that the Tazlina, Barnette, and Scarp sections crystallized at successively greater depths. Temperature was calculated using hbl- plg [Holland and Blundy, 1994] and cpx-opx [QUILF; Andersen et al., 1993] net- transfer equilibria, and P was constrained using high δV/δS equilibria among plg, amph, opx, and cpx. Poorly known amphibole and pyroxene Tschermak-component activity models yield large uncertainties for P, but relative P differences can be anchored to the better-determined garnet gabbro P's, revealing that the rocks from the Barnette Creek section crystallized at ~0.40-0.55 GPa and the Tazlina and Pippin sections formed at ~0.25-0.35 GPa. Al-in-hornblende barometry indicates 0.23 GPa for granodiorites intruding the volcanic section. Calc-silicate rocks within the arc include metasedimentary wall rocks and carbonate veins cutting igneous rock. Grossular-andradite + diopside + calcite +/- sphene + quartz +/- wollastonite +/- scapolite mineral assemblages were strongly overprinted by a prehnite-pumpellyite facies alteration that includes datolite. Calculating P-T for the calc-silicate rocks is tenuous for several reasons-including large calculated Fe3+ in garnet and cpx, complete replacement of plagioclase, extreme partitioning of Mg into cpx, and ill-constrained aCO2--but a general correspondence between P-T inferred for the calc-silicate rocks and nearby metamafic rocks suggests that the calc-silicate assemblages grew during the magmatic development of the arc. Metamorphic rocks in float of the McHugh Complex(?) structurally beneath the Klanelneechena Klippe contain a strong amphibolite-facies fabric formed at 500°C and 1.0 ± 0.1 GPa. In summary, the granodiorites intruded at c. 6-10 km into a volcanic section estimated from stratigraphy to be 7 km thick [Clift et al., 2005]. The shallowest, Tazlina and Pippin, gabbros cooled at ~9-12 km; the Barnette section at ~14-19 km; the Klanelneechena klippe at ~24-26 km; and the base of the arc at ~30-34 km depth. Thus, the arc consists of a volcanic:plutonic ratio of ~28:72, and the current 5-7 km structural thickness of the plutonic section of the arc is ~20-35% of the original 20-26 km thickness.

Mass loss of TEOS-coated RCC subjected to the environment at the shuttle wing leading edge

NASA Technical Reports Server (NTRS)

Stroud, C. W.; Rummler, D. R.

1981-01-01

Coated, reinforced carbon-carbon (RCC) is used for the leading edges of the Space Shuttle. The mass loss characteristics of RCC specimens coated with tetra-ethyl-ortho-silicate (TEOS) were determined for conditions which simulated the entry environment expected at the stagnation area of the wing leading edge. Maximum specimen temperature was 1632 K. Specimens were exposed for up to 100 missions. Stress levels up to 8.274 MPa caused an average increase in oxidation of 6 percent over unstressed specimens. Experimentally determined mass losses were compared with those predicted by an existing empirical analysis.

Studies related to the evolution of the lunar soil materials

NASA Technical Reports Server (NTRS)

Carter, J. L.

1973-01-01

Studies of the chemistry and morphology of the lunar samples are reported. The presence of fragments of plagoclase in the centers of the impact craters indicate that the glass spheres were derived by meteoritic impact from high velocity particles, while the glass was at high temperatures. From the study of the Apollo 16 samples, it is suggested that this material was formed in a hot impact ejecta blanket, or in an igneous environment, and later exposed to meteoritic impact. It is suggested that particles from Apollo 17 were formed in a cloud of siliceous vapors.

Monitoring Io's Volcanic Activity in the Visible and Infrared from JUICE - It's All About (Eruption) Style

NASA Astrophysics Data System (ADS)

Davies, A. G.; Matson, D.; McEwen, A. S.; Keszthelyi, L. P.

2012-12-01

The European Space Agency's Jupiter Icy Moons Explorer (JUICE) will provide many opportunities for long-range monitoring of Io's extraordinary silicate, high-temperature volcanic activity [1, 2]. A considerable amount of valuable work can be performed even with relatively low-spatial-resolution observations [2]. Techniques developed from the examination and analysis of Galileo Near Infrared Mapping Spectrometer (NIMS) data, as well as observations of terrestrial silicate volcanic activity, allows the identification of likely eruption style [2] at many locations where the entire eruption is sub-pixel. Good temporal coverage, especially for episodic eruptions (including high-energy "outburst" eruptions), is important for modelling purposes. With opportunities to observe Io on a regular basis (hours-days) during cruise/orbital reduction phases, a visible-to-near-infrared mapping spectrometer (covering ~0.4-5.5 μm) is the best instrument to chart the magnitude and variability of Io's volcanic activity, allowing comparison with an existing and constantly expanding set of Io observations [e.g. 1, 3]. The eruption temperature of Io's dominant silicate lava, a constraint on interior composition and conditions, is a major unanswered question in the wake of the Galileo mission [1]. A careful approach to instrument design is needed to ensure that observations by both imager and IR spectrometer on JUICE are capable of determining lava eruption temperature [e.g., 4] in low spatial resolution data. With an ideal thermal target (e.g., an outburst eruption, or the proposed lava lake at Pele) the imager should obtain multi-spectral data in a rapid sequence to allow stability of the thermal source to be quantified. Observations by imager and spectrometer have to be contemporaneous and unsaturated. References: [1] Davies, A. (2007) "Volcanism on Io", Cam. Univ. Press. [2] Davies, A. et al. (2010) JVGR, 194, 75-99. [3] Veeder, G. et al. (2012) Icarus, 219, 701-722. [4] Davies, A. et al. (2011) GRL, 38, L21308. This work was performed at the Jet Propulsion Laboratory-California Institute of Technology, under NASA contract. AGD thanks the NASA Outer Planets Research Program for support.

Installation Restoration Program (IRP) for IRP Sites Numbers 4, 5, 7 and 14. 152 Tactical Reconnaissance Group, Nevada Air National Guard, Reno Tahoe International Airport, Reno, Nevada

DTIC Science & Technology

1996-01-01

For: HQ/ANG/CEVR Andrews AFB, Maryland Prepared By: ERM-West, Inc. 5111. N. Scottsdale Road, Suite 108 ERM Scottsdale, Arizona 85250 FINAL Document...predominantly andesite and andesite porphyry flow rock, hypabyssal intrusives, and minor siliceous welded tuff, which are commonly represented by the Kate...TERTIARY ROCKSI tuslýýj porphyry and olcomic brii I SOURCE ORNL/ETS. 1994 GEOLOGIC MAP OF THE FIGURE 3-1 RENO. NEVADA AREA 152nd TACTICAL RECONNAISSANCE

Trace element content of gossans at four mines in the West Shasta massive sulfide district.

USGS Publications Warehouse

Sanzolone, R.F.; Domenico, J.A.

1985-01-01

Paired analyses of the spongy whole-rock gossan and its botryoidal crust ("chipped rock rind') show little differences, whereas duplicate samples of each at individual sites show such extreme differences as to preclude the use of the data in areal mapping. Gossans from disseminated sulphides have lower and less variable trace-element contents than gossans from massive sulphides, due in part to dilution by rock silicates. Computer reduction of the data by a regionalizing algorithm enables determination of pattern differences among the four mines.-G.J.N.

Role of Clay Minerals in Long-Distance Transport of Landslides in Valles Marineris, Mars

NASA Astrophysics Data System (ADS)

Watkins, J.; Ehlmann, B. L.; Yin, A.

2014-12-01

Long-runout (> 50 km) subaerial landslides are rare on Earth, but are common features episodically shaping Mars' Valles Marineris (VM) trough system over the past 3.5 billion years. They display two end-member morphologies: a thick-skinned inner zone, characterized by fault-bounded, rotated blocks near their source region, and a thin-skinned, exceptionally long-runout outer zone, characterized by thin sheets spreading over 10s of km across the trough floor. Four decades of studies on the latter have resulted in two main competing hypotheses to explain their long-distance transport: (1) movement of landslides over layers of trapped air or soft materials containing ice or snow, enabling basal lubrication, and (2) fluidization of landslide materials with or without the presence of water and volatiles. To address this issue, we examine the mineralogic composition of landslides across VM using Compact Reconnaissance Imaging Spectrometer for Mars (CRISM) near-infrared spectral data analysis coupled with detailed geologic mapping and morphometric analysis of satellite images. Our survey reveals a general correlation between transport distance, significant lateral spreading, and the presence of hydrated silicates among VM landslides. Given that smectite clay absorbs water into its layered crystal structure and can reduce the friction coefficient by a factor of three v. that of dry rocks, these results suggest that hydrated silicates played a decisive role in facilitating long-runout landslide transport in VM. We propose that, concurrent with downslope failure and sliding of broken trough-wall rock, frontal landslide masses overrode and entrained hydrated-silicate-bearing trough-floor deposits, lubricating the basal sliding zones and permitting the landslide outer zones to spread laterally while moving forward over the low-friction surface. The key participation of hydrated silicates in episodic, sustained landslide activity throughout the canyon implies that clay minerals, generated by water-rock interactions in the Noachian and Hesperian (4.1- 3.3 Ga), exert a long-lasting influence on geomorphic processes that shape the surface of the planet.

Silicate calculi, a rare cause of kidney stones in children.

PubMed

Taşdemir, Mehmet; Fuçucuoğlu, Dilara; Özman, Oktay; Sever, Lale; Önal, Bülent; Bilge, Ilmay

2017-02-01

Urinary silicate calculi in humans are extremely rare. Reported cases of silicate calculi are mostly documented in adults and are commonly related to an excessive intake of magnesium trisilicate in food or drugs. Published studies on the presence of silicate calculi in children are scarce. Three cases of silicate kidney stones without prior silicate intake are reported. Two patients underwent surgical treatment, and the third patient was treated using conservative methods. Urinalysis revealed no underlying metabolic abnormalities. Analyses revealed that silicate was the major component of the stones. Siliceous deposits in urinary stones may be more common than anticipated, and the underlying pathophysiology remains to be clarified.

Space-weathering processes and products on volatile-rich asteroids

NASA Astrophysics Data System (ADS)

Britt, D.; Schelling, P.; Consolmagno, G.; Bradley, T.

2014-07-01

Space weathering is a generic term for the effects on atmosphereless solid bodies in the solar system from a range of processes associated with direct exposure to the space environment. These include impact processes (shock, vaporization, fragmentation, heating, melting, and ejecta formation), radiation damage (from galactic and solar cosmic rays), solar-wind effects (irradiation, ion implantation, and sputtering), and the chemical reactions driven by these processes. The classic example of space weathering is the formation of the lunar spectral red slope associated with the production of nanophase Fe (npFe0) in the dusty lunar regolith (C.R. Chapman, 2004, Annual Review of Earth & Planet. Sci. 32, C.M. Pieters, 2000, MAPS 35). Similar npFe0 has been recovered from asteroid (25143) Itokawa and some asteroid classes do exhibit modest spectral red slopes (T. Noguchi, 2011, Science 333). Space weathering can be thought of as driven by a combination of the chemical environment of space (hard vacuum, low oxygen fugacity, solar-wind implantation of hydrogen) along with thermal energy supplied by micrometeorite impacts. The forward modeling of space weathering as thermodynamically-driven decomposition of common rock-forming minerals suggests the production of a range of daughter products: (1) The silicate products typically lose oxygen, other volatile elements (i.e., sulfur and sodium), and metallic cations, producing minerals that are typically more disordered and less optically active than the original parent materials. (2) The decomposed metallic cations form in nano-sized blebs including npFe0, on the surfaces or in condensing rims of mineral grains. This creates a powerful optical component as seen in the lunar red slope. Surfaces with exposed npFe0 are an ideal environment for catalyzing further reactions. (3) The liberated volatile elements and gases (O, S, Na) may form an observable exosphere (e.g., Moon and Mercury) and can either escape from the body or recombine with available solar-wind-implanted hydrogen to form trace amounts of water and OH. Mineral decomposition can be thought of as the first stage of space weathering. It produces weathered surfaces somewhat depleted in volatile elements, creates a predictable set of minor or trace minerals, and leaves the surfaces with catalytic species, primarily npFe0. However, a second stage of further reactions and weathering depends upon the presence of ''feed-stock'' components that can participate in catalyzed chemical reactions on exposed surfaces. For volatile-rich small bodies, the available materials are not only silicates, but a volatile feedstock that can include water, carbon monoxide, ammonia, to name a few. Thermodynamically-driven decomposition of silicates will produce trace amounts of npFe0 which are ideal sites for Fischer-Tropsch type (FTT) catalytic reactions that can produce organics in situ on the asteroids including alkanes, polyaromatic hydrocarbons, and amino acids (J.E. Elsila, 2012, MAPS 47). The mix and range of products depends on the composition and morphology of the mineral surface, energy inputs produced by the micrometeorite impacts or other processes, and the composition of the input volatile feedstock. FFT reactions generate long-chain carbon compounds and amino acids. Secondary reactions that generate more complex carbon compounds and amino acids are likely to occur as the organic material matures. Weathering maturity can be thought of as a function of the abundance and diversity of the weathering products. Since the npFe0 is not destroyed in the reaction, continued micrometeorite bombardment would result in continuing processing and recombination of the existing organic feedstock. More weathering would result in progressively longer-chain carbon compounds as well as more complex and diverse amino acids, and eventually the kerogen-like insoluble-organic matter that forms a large fraction of carbonaceous meteorites. This insight has several major implications for our planetary science and, potentially, the formation of the precursors of life. First, the range of weathering products seen in remotely-sensed data, meteorites, and returned samples are not random, but the predictable outcome of the source region's mineral kinetics and chemical feedstock. Weathering products do not have to be optically active like the npFe0 that produces the lunar red slope; on the contrary, probably most weathering products are spectrally neutral or even suppress an object's near-IR reflectance spectrum. In the case of volatile-rich parent bodies, a major weathering product is a range of carbon-rich compounds. But an additional result of considerable interest is the generation of pre-biotic compounds as a routine and predictable byproduct of common space-weathering processes. Any atmosphereless body around any star with mafic silicate mineral compositions and volatile feedstocks should create amino acids as a standard byproduct of space weathering. The precursors of life are probably abundant in any space-weathered asteroid belt, in any solar system, and only wait being accreted to a hospitable environment.

Crustal extension and magmatism during the mid-Cenozoic ignimbrite flare-up in the Guazapares Mining District and Cerocahui basin regions, northern Sierra Madre Occidental, western Chihuahua, Mexico

NASA Astrophysics Data System (ADS)

Murray, Bryan Patrick

Silicic large igneous provinces are significant in the geologic record, due to their unusually extensive areal coverage (>100,000 km2) and large volumes (>250,000 km3), and may be characteristic of continental regions undergoing broad lithospheric extension. The Sierra Madre Occidental of northwestern Mexico is the biggest and best-preserved silicic large igneous province of the Cenozoic and is considered part of the extensive mid-Cenozoic ignimbrite flare-up that affected much of the southwestern North American Cordillera. Despite its size and preservation, very little is known about the geology of the Sierra Madre Occidental, and the timing and spatial extent of ignimbrite flare-up volcanism in relation to crustal extension is relatively unknown. This study presents new geologic mapping, stratigraphy, zircon U-Pb laser ablation ICP-MS dating, modal analysis, and geochemical data from the Guazapares Mining District and Cerocahui basin regions, two adjacent areas of the northern Sierra Madre Occidental in western Chihuahua. The rock exposure and topographic relief in this previously unmapped ~450 km2 area make it ideal for studying the relationships between silicic large igneous province volcanism and crustal extension. Three informal formations are identified in the study area: (1) the ca. 27.5 Ma Parajes formation, a ~1-km-thick succession of primarily welded silicic outflow ignimbrite sheets erupted from sources within ~50--100 km of the study area that were active during the Early Oligocene pulse of the mid-Cenozoic ignimbrite flare-up; (2) the ca. 27--24.5 Ma Temoris formation, composed primarily of locally erupted mafic-intermediate lavas and associated intrusions with interbedded alluvial deposits, likely related to rocks of the Southern Cordillera basaltic andesite province that were intermittently erupted across all of the northern Sierra Madre Occidental following the Early Oligocene ignimbrite pulse; and (3) the ca. 24.5--23 Ma Sierra Guazapares formation, composed of silicic vent to proximal facies ignimbrites, lavas, plugs, and reworked equivalents that record the initiation of explosive and effusive silicic fissure magmatism in the study area during the Early Miocene pulse of the mid-Cenozoic ignimbrite flare-up. The Guazapares Mining District and Cerocahui basin regions share this stratigraphy, but the rocks in the Cerocahui basin consist of a much higher proportion of alluvial deposits. The main geologic structures in the Guazapares Mining District and Cerocahui basin regions are NNW-trending normal faults, with an estimated minimum of 20% total horizontal extension. Many normal faults bound half-graben basins that show evidence of syndepositional extension. Normal faulting began by ca. 27.5 Ma during deposition of the youngest ignimbrites of the Parajes formation, concurrent with the end of the Early Oligocene silicic ignimbrite pulse of the ignimbrite flare-up to the east and before magmatism began in the study area. Preexisting normal faults localized mafic-intermediate volcanic vents of the Temoris formation and silicic vents of the Sierra Guazapares formation, and were active during deposition of these formations. In addition, the localization and timing of epithermal mineralization in the Guazapares Mining District appears to be favored where pre-to-synvolcanic extensional structures are in close association with Sierra Guazapares formation rhyolite plugs. The timing of extensional faulting and magmatism in the Guazapares Mining District and Cerocahui regions is consistent with regional-scale Middle Eocene to Early Miocene southwestward migration of active volcanism and extension in the northern Sierra Madre Occidental. Extension accompanied mafic-intermediate and silicic volcanism in the study area, and overlapped with the peak of mid-Cenozoic ignimbrite flare-up in the Sierra Madre Occidental; this supports the interpretation that there is likely a relationship between lithospheric extension and silicic large igneous province magmatism.

Recognizing subtle evidence for silicic magma derivation from petrochemically-similar arc crust: Isotopic and chemical evidence for the bimodal volcanic series of Gorely Volcanic Center, Kamchatka, Russia

NASA Astrophysics Data System (ADS)

Seligman, A. N.; Bindeman, I. N.; Ellis, B. S.; Ponomareva, V.; Leonov, V.

2012-12-01

The Kamchatka Peninsula is home to some of the most prolific subduction related volcanic activity in the world. Gorely caldera and its central volcano are located in the rear of its currently active Eastern Volcanic Front. Recent work determined the presence of explosive ignimbrite eruptions sourced from Gorely volcano during the Pleistocene. We studied 32 eruptive units, including tephrochronologically-dated Holocene tephra, stratigraphically-arranged ignimbrites, as well as pre- and post-caldera lavas. We analyzed oxygen isotope ratios of pyroxene and plagioclase grains by laser fluorination, and major and trace element compositions of whole rocks. In addition, we determined 87Sr/86Sr and 143Nd/144Nd ratios of caldera-forming ignimbrite eruptions. Chemical compositions show that Gorely eruptive units range from basalt to basaltic andesite in the "Pra-Gorely" stages prior to caldera formation and the modern Gorely stages forming its current edifice. In contrast, eruptive material from earlier ignimbrites exposed at Opasny Ravine consists primarily of dacite. Whole rock analyses for Gorely indicate that silicic rocks and ignimbrites volumetrically dominate all other products, forming separate bimodal peaks in our SiO2-frequency diagram. In addition, trace element concentrations and ratios define two trends, one for more silicic and another for more mafic material. δ18Omelt values range from a low of 4.85 up to 6.22‰, where the lowest value was found in the last caldera forming eruption, suggesting incorporation of hydrothermally-altered material from earlier eruptions. 87Sr/86Sr and 143Nd/144Nd ratios range from 0.70328 to 0.70351 and from 0.51303 to 0.51309 respectively, with higher and more diverse values being characteristic of earlier ignimbrite units; again suggesting incorporation of surrounding crustal material. In contrast to these results, MELTS modeling using a variety of likely primitive basalts from Gorely shows it is possible to obtain silicic chemical compositions near the evolved ignimbrite compositions, strictly through 70-80% fractional crystallization at 1-2 kbars and NNO oxygen fugacity. The combination of light δ18O values as well as elevated 87Sr/86Sr and low 143Nd/144Nd values, in addition to the volumetric excess of silicic rocks suggest assimilation of the older and petrochemically-similar country-rocks (Karymshina volcano and/or the underlying Akhomten Massif). This research can be utilized for studies of other volcanoes at "long-term centers", underscoring the importance of using both isotopes and modeling of fractional crystallization to determine silicic magma derivation through coupled shallow crustal assimilation of similar older material and fractional crystallization.

Geologic map of the Dusar area, Herat Province, Afghanistan; Modified from the 1973 original map compilations of V.I. Tarasenko and others

USGS Publications Warehouse

Tucker, Robert D.; Stettner, Will R.; Masonic, Linda M.; Bogdanow, Anya K.

2017-10-24

The geologic maps and cross sections presented in this report are redrafted and modified versions of the Geologic map and map of useful minerals of the Dusar area (scale 1:50,000) and Geologic sketch map of the Dusar and Namak-sory ore occurrences (scale 1:10,000), located in the Herat Province, Afghanistan. The original maps and cross sections are contained in unpublished Soviet report no. 0290 (Tarasenko and others, 1973) prepared in cooperation with the Ministry of Mines and Industries of the Royal Government of Afghanistan, in Kabul during 1973 under contract no. 50728. The redrafted maps and cross sections (modified from Tarasenko and others, 1973) illustrate the geological structure and mineral occurrences of the Dusar copper-gold-silver-lead-zinc prospect area of western Afghanistan, located within the Dusar-Shaida copper and tin area of interest (AOI), Herat Province, Afghanistan.Mineralization in the Dusar area is hosted within Early Jurassic to Early Cretaceous stratified volcanic and sedimentary rocks associated with numerous diabase and gabbro-diabase intrusive bodies and is generally near a major northeast-trending system of faults and quartz veins. Host rocks consist of quartz keratophyre and quartz-feldspar porphyry, with layers of schist, phyllite, and quartz-chlorite and chlorite-sericite slate; and limestone and shale, with schist and carbonate-chlorite and chlorite slate. Known mineralization includes an extensive quartz vein system, shown on the map as the “northern occurrence,” as well as the Dusar and Namak-sory gossan zones, interpreted to have formed from remnant pyrite mineralization. The veins of the northern occurrence and their altered host rocks are known to contain anomalous to economic concentrations of precious and base metals, with concentrations locally in excess of 2 parts per million gold, 100 parts per million silver, 5 percent copper, and 1 percent lead. These veins occur in swarms, and are hosted along structures that are approximately concordant with the plane of the metamorphic fabric. The veins consist mostly of quartz, with minor carbonate and sulfide minerals, and display weak alteration halos along their margins. The gossans are locally anomalous in these metals, but their size and extent makes them attractive exploration targets for potential massive sulfide mineralization.The Dusar gossan zone is a massive, ochreous, and siliceous limonitic rock, approximately 2,200 meters long, 30 to 250 meters wide, and 2.0 to 7.2 meters thick. Drilling below the Dusar gossan intersected a siliceous, sericitic, and limonitic rock underlain by quartz keratophyre with abundant disseminated pyrite. Mineralized sections grade 0.06 weight percent copper and up to 0.05 weight percent zinc. The Namak-sory gossan zone contains a similar deposit with anomalous concentrations of copper, zinc, and gold.The redrafted maps and cross sections reproduce the topology of rock units, contacts, and faults of the original Soviet maps and cross sections, and include minor modifications based on examination of the originals and observations made during two brief field visits by USGS staff in August, 2010, and June, 2013.

Characteristics of Vibration that Alter Cardiovascular Parameters in Mice

PubMed Central

Li, Yao; Rabey, Karyne N; Schmitt, Daniel; Norton, John N; Reynolds, Randall P

2015-01-01

We hypothesized that short-term exposure of mice to vibration within a frequency range thought to be near the resonant frequency range of mouse tissue and at an acceleration of 0 to 1 m/s2 would alter heart rate (HR) and mean arterial pressure (MAP). We used radiotelemetry to evaluate the cardiovascular response to vibration in C57BL/6 and CD1 male mice exposed to vertical vibration of various frequencies and accelerations. MAP was consistently increased above baseline values at an acceleration near 1 m/s2 and a frequency of 90 Hz in both strains, and HR was increased also in C57BL/6 mice. In addition, MAP increased at 80 Hz in individual mice of both strains. When both strains were analyzed together, mean MAP and HR were increased at 90 Hz at 1 m/s2, and HR was increased at 80 Hz at 1 m/s2. No consistent change in MAP or HR occurred when mice were exposed to frequencies below 80 Hz or above 90 Hz. The increase in MAP and HR occurred only when the mice had conscious awareness of the vibration, given that these changes did not occur when anesthetized mice were exposed to vibration. Tested vibration acceleration levels lower than 0.75 m/s2 did not increase MAP or HR at 80 or 90 Hz, suggesting that a relatively high level of vibration is necessary to increase these parameters. These data are important to establish the harmful frequencies and accelerations of environmental vibration that should be minimized or avoided in mouse facilities. PMID:26224436

Digital geologic map of the Thirsty Canyon NW quadrangle, Nye County, Nevada

USGS Publications Warehouse

Minor, S.A.; Orkild, P.P.; Sargent, K.A.; Warren, R.G.; Sawyer, D.A.; Workman, J.B.

1998-01-01

This digital geologic map compilation presents new polygon (i.e., geologic map unit contacts), line (i.e., fault, fold axis, dike, and caldera wall), and point (i.e., structural attitude) vector data for the Thirsty Canyon NW 7 1/2' quadrangle in southern Nevada. The map database, which is at 1:24,000-scale resolution, provides geologic coverage of an area of current hydrogeologic and tectonic interest. The Thirsty Canyon NW quadrangle is located in southern Nye County about 20 km west of the Nevada Test Site (NTS) and 30 km north of the town of Beatty. The map area is underlain by extensive layers of Neogene (about 14 to 4.5 million years old [Ma]) mafic and silicic volcanic rocks that are temporally and spatially associated with transtensional tectonic deformation. Mapped volcanic features include part of a late Miocene (about 9.2 Ma) collapse caldera, a Pliocene (about 4.5 Ma) shield volcano, and two Pleistocene (about 0.3 Ma) cinder cones. Also documented are numerous normal, oblique-slip, and strike-slip faults that reflect regional transtensional deformation along the southern part of the Walker Lane belt. The Thirsty Canyon NW map provides new geologic information for modeling groundwater flow paths that may enter the map area from underground nuclear testing areas located in the NTS about 25 km to the east. The geologic map database comprises six component ArcINFO map coverages that can be accessed after decompressing and unbundling the data archive file (tcnw.tar.gz). These six coverages (tcnwpoly, tcnwflt, tcnwfold, tcnwdike, tcnwcald, and tcnwatt) are formatted here in ArcINFO EXPORT format. Bundled with this database are two PDF files for readily viewing and printing the map, accessory graphics, and a description of map units and compilation methods.

Hot spots on Io: Initial results from Galileo's near infrared mapping spectrometer

USGS Publications Warehouse

Lopes-Gautier, R.; Davies, A.G.; Carlson, R.; Smythe, W.; Kamp, L.; Soderblom, L.; Leader, F.E.; Mehlman, R.

1997-01-01

The Near-Infrared Mapping Spectrometer on Galileo has monitored the volcanic activity on Io since June 28, 1996. This paper presents preliminary analysis of NIMS thermal data for the first four orbits of the Galileo mission. NIMS has detected 18 new hot spots and 12 others which were previously known to be active. The distribution of the hot spots on Io's surface may not be random, as hot spots surround the two bright, SO2-rich regions of Bosphorus Regio and Colchis Regio. Most hot spots seem to be persistently active from orbit to orbit and 10 of those detected were active in 1979 during the Voyager encounters. We report the distribution of hot spot temperatures and find that they are consistent with silicate volcanism. Copyright 1997 by the American Geophysical Union.

DNA double-strand breaks caused by new and contemporary endodontic sealers.

PubMed

Eldeniz, A U; Shehata, M; Högg, C; Reichl, F X

2016-12-01

To investigate the cytotoxicity and genotoxicity of a new silicate-based BioRoot RCS ® sealer in comparison with contemporary sealers. A periodontal ligament cell line using lentiviral gene transfer of human telomerase reverse transcriptase (hTERT) was used and exposed to subtoxic concentrations of 24-h eluates from two epoxy resin-based (AH Plus Jet ® and Acroseal ® ), four various methacrylate-based endodontic sealers (EndoREZ ® , RealSeal ® , RealSeal SE ® and Hybrid Root SEAL ® ) and three silicate-based sealers (BioRoot RCS ® , iRootSP ® and MTA Fillapex ® ). The XTT-based cell viability assay was used for cytotoxicity screening of materials. The γ-H2AX assay was used for genotoxicity screening. In the γ-H2AX immunofluorescence assay, PDL-hTERT cells were exposed to eluates of the substances for 6 h and DNA double-strand breaks (DSB) were detected microscopically. Induced foci represented DSBs, which can induce ATM-dependent phosphorylation of the histone H2AX. The statistical significance of the differences between the experimental groups was compared using the Student's t-test (P < 0.05). The cytotoxicity of the 24-h eluates could be ranked in the following order: Hybrid Root SEAL ® >RealSeal ® >Acroseal ® >RealSeal SE ® ≥ AH Plus Jet ® > EndoREZ ® >MTA Fillapex ® > iRoot SP ® >BioRoot RCS ® . In negative controls (cells which received medium only) 4.08 ± 0.53 DSB foci (mean ± SEM) whilst in positive controls 10.76 ± 4.05 DSB foci/cell were found. BioRoot RCS ® and RealSeal SE ® exhibited significant differences in foci formation at 1/3 EC50 compared with their 1/10 EC50 concentration (P < 0.05). Both concentrations (1/10 and 1/3 of EC50) of AH Plus Jet ® , Acroseal ® , RealSeal ® and MTA Fillapex ® sealers were not significantly different when compared with the medium control (P < 0.05). New BioRoot RCS ® was not toxic whilst Hybrid Root SEAL ® demonstrated more toxicity and DNA double-strand breaks when compared with other resin- and silicate-based root canal sealers. © 2015 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Influence of light and oxygen on the color stability of five calcium silicate-based materials.

PubMed

Vallés, Marta; Mercadé, Montse; Duran-Sindreu, Fernando; Bourdelande, Jose L; Roig, Miguel

2013-04-01

Difficult handling, long setting time, and potential discoloration are important drawbacks of white mineral trioxide aggregate (WMTA). The development of Biodentine, a recently developed calcium silicate-based material (CSM), has overcome some of these shortcomings; however, there are no available data on its color stability. A previous study showed that WMTA discolors under light irradiation in an oxygen-free environment. The present study evaluated the influence of light irradiation and oxygen on the color stability of 5 CSMs. Fifteen samples of 5 CSMs (ProRoot WMTA, Angelus WMTA, White Portland Cement [PC], PC with bismuth oxide, and Biodentine) were divided into 5 groups. Each group was exposed to different oxygen and light conditions. A spectrophotometer was used to determine the color of each specimen at 0, 120 seconds, and 5 days. Data were analyzed by using analysis of variance and Tukey honestly significant difference test. The materials PC with bismuth oxide, Angelus WMTA, and ProRoot WMTA showed dark discoloration after light irradiation in an oxygen-free environment, which was statistically significantly different from Biodentine and PC. In groups that were exposed to no light irradiation or to an oxygen atmosphere, all materials showed color stability over time, and no significant differences were observed among them. PC and Biodentine maintained color stability in all conditions over time and showed no significant differences. The combination of light and anaerobic conditions (similar to those in clinical situations) results in differences in color of the tested CSMs during a period of 5 days, of which Biodentine and PC demonstrated color stability. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Dentinogenic responses after direct pulp capping of miniature swine teeth with Biodentine.

PubMed

Tziafa, Christina; Koliniotou-Koumpia, Eugenia; Papadimitriou, Serafim; Tziafas, Dimitrios

2014-12-01

The aim of this study was to evaluate pulpal responses after experimental direct pulp capping of mechanically exposed teeth with a new calcium silicate-based dentin replacement material. Thirty-four anterior and posterior teeth of 3 miniature swine were used. Class V or I cavities were prepared on the buccal or occlusal surfaces, respectively. Pulpal exposures were further performed using a round carbide bur 0.8 mm in diameter. Exposures were treated with white MTA Angelus (Angelus, Londrina, PR, Brazil) or Biodentine (Septodont, Saint Maur des Fosses, France), and the cavities were further restored with Biodentine. The pulpal tissue responses were histologically assessed at postoperative periods of 3 and 8 weeks. Data were statistically analyzed using the Kruskal Wallis and the Mann-Whitney U tests. Inflammatory infiltration or pulp tissue necrosis was not found in any of the specimens. All teeth showed mineralized matrix formation in the form of a complete hard tissue bridge composed of osteodentin or osteodentin followed by a discontinuous or continuous reparative dentin zone. A significantly higher thickness of the hard tissue bridge was found in the group of teeth treated with Biodentine at both 3 and 8 weeks. A number of teeth, which were under root development at the onset of the experimental procedures, exhibited ectopic pulp calcification. The application of both calcium silicate-based materials in direct contact with the mechanically exposed pulp of healthy miniature swine teeth led to pulp repair with complete hard tissue bridge formation. The thickness of hard tissue bridges was significantly higher after pulp capping with Biodentine. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Preliminary isostatic residual gravity anomaly map of Paso Robles 30 x 60 minute quadrangle, California

USGS Publications Warehouse

McPhee, D.K.; Langenheim, V.E.; Watt, J.T.

2011-01-01

This isostatic residual gravity map is part of an effort to map the three-dimensional distribution of rocks in the central California Coast Ranges and will serve as a basis for modeling the shape of basins and for determining the location and geometry of faults within the Paso Robles quadrangle. Local spatial variations in the Earth\\'s gravity field, after accounting for variations caused by elevation, terrain, and deep crustal structure reflect the distribution of densities in the mid- to upper crust. Densities often can be related to rock type, and abrupt spatial changes in density commonly mark lithological or structural boundaries. High-density rocks exposed within the central Coast Ranges include Mesozoic granitic rocks (exposed northwest of Paso Robles), Jurassic to Cretaceous marine strata of the Great Valley Sequence (exposed primarily northeast of the San Andreas fault), and Mesozoic sedimentary and volcanic rocks of the Franciscan Complex [exposed in the Santa Lucia Range and northeast of the San Andreas fault (SAF) near Parkfield, California]. Alluvial sediments and Tertiary sedimentary rocks are characterized by low densities; however, with increasing depth of burial and age, the densities of these rocks may become indistinguishable from those of older basement rocks.

Mineralogy, Petrology, Chemistry, and Ar-39 - Ar-40 and Ages of the Caddo County IAB Iron: Evidence for Early Partial Melt Segregation of a Gabbro Area Rich in Plagioclase-Diopside

NASA Technical Reports Server (NTRS)

Takeda, Hiroshi; Bogard, Donald D.; Mittlefehldt, David W.; Garrison, Daniel H.

2000-01-01

We found coarse-grained gabbroic material rich in plagioclase and diopside in the Caddo County IAB iron meteorite. The polished thin sections studied were made from areas rich in Al and Ca detected by a micro-focus X-ray fluorescence (XRF) mapping technique. The gabbro is not a clast within a breccia, but rather this area is located mainly at silicate-metal boundaries only a few cm away from an area with fine-grained, ultramafic silicate similar to winonaites. Medium-grained orthopyroxene and olivine are found in transitional areas showing no disturbance of their crystalline textures. A vein-like region, starting at the area rich in fine-grained mafic silicate, extends towards the gabbroic area with a gradual increase in abundance of plagioclase and diopside. This texture and our accumulated knowledge of the formation mechanism of IAB/winonaltes meteorites, suggest that the gabbroic materials were formed by inhomogeneous segregation of partial melts of chondritic source materials. Compositional data on two mineralogically distinct samples of the gabbro-rich portion of the inclusion were obtained by INAA. Compared to an average of LAB silicate inclusions or winonaites, the Caddo County gabbro is enriched in the incompatible lithophile elements Na, Ca, Sc, REE and Hf, which is consistent with a melt origin for the gabbro. The cosmogenic space exposure age of Caddo County (511 Ma) is significantly younger than exposure ages of some other IAB meteorites, An 39Ar-40Ar age determination of the gabbroic material indicates a series of upward steps in age from 4.516 Ga to 4.523 Ga, with a few high temperature ages up to 4.54 Ga. The older age could approximate the primary recrystallization age of silicates. The stepped Ar age spectrum may indicate differences in Ar closure temperatures during slow cooling of -2-20'C/Myr in the parent body. Alternatively, the younger Ar-Ar ages may date a shock event which occurred while Caddo County was hot and which also created textures such as a linear metal vein with rounded zigzag walls in a diopside crystal and slightly miss-oriented rounded plagioclase domain.

Modifying Silicates for Better Dispersion in Nanocomposites

NASA Technical Reports Server (NTRS)

Campbell, Sandi

2005-01-01

An improved chemical modification has been developed to enhance the dispersion of layered silicate particles in the formulation of a polymer/silicate nanocomposite material. The modification involves, among other things, the co-exchange of an alkyl ammonium ion and a monoprotonated diamine with interlayer cations of the silicate. The net overall effects of the improved chemical modification are to improve processability of the nanocomposite and maximize the benefits of dispersing the silicate particles into the polymer. Some background discussion is necessary to give meaning to a description of this development. Polymer/silicate nanocomposites are also denoted polymer/clay composites because the silicate particles in them are typically derived from clay particles. Particles of clay comprise layers of silicate platelets separated by gaps called "galleries." The platelet thickness is 1 nm. The length varies from 30 nm to 1 m, depending on the silicate. In order to fully realize the benefits of polymer/silicate nanocomposites, it is necessary to ensure that the platelets become dispersed in the polymer matrices. Proper dispersion can impart physical and chemical properties that make nanocomposites attractive for a variety of applications. In order to achieve nanometer-level dispersion of a layered silicate into a polymer matrix, it is typically necessary to modify the interlayer silicate surfaces by attaching organic functional groups. This modification can be achieved easily by ion exchange between the interlayer metal cations found naturally in the silicate and protonated organic cations - typically protonated amines. Long-chain alkyl ammonium ions are commonly chosen as the ion-exchange materials because they effectively lower the surface energies of the silicates and ease the incorporation of organic monomers or polymers into the silicate galleries. This completes the background discussion. In the present improved modification of the interlayer silicate surfaces, the co-ion exchange strengthens the polymer/silicate interface and ensures irreversible separation of the silicate layers. One way in which it does this is to essentially tether one amine of each diamine molecule to a silicate surface, leaving the second amine free for reaction with monomers during the synthesis of a polymer. In addition, the incorporation of alkyl ammonium ions into the galleries at low concentration helps to keep low the melt viscosity of the oligomer formed during synthesis of the polymer and associated processing - a consideration that is particularly important in the case of a highly cross-linked, thermosetting polymer. Because of the chemical bonding between the surface-modifying amines and the monomers, even when the alkyl ammonium ions become degraded at high processing temperature, the silicate layers do not aggregate and, hence, nanometer-level dispersion is maintained.

Impact of a community-based prevention marketing intervention to promote physical activity among middle-aged women.

PubMed

Sharpe, Patricia A; Burroughs, Ericka L; Granner, Michelle L; Wilcox, Sara; Hutto, Brent E; Bryant, Carol A; Peck, Lara; Pekuri, Linda

2010-06-01

A physical activity intervention applied principles of community-based participatory research, the community-based prevention marketing framework, and social cognitive theory. A nonrandomized design included women ages 35 to 54 in the southeastern United States. Women (n = 430 preprogram, n = 217 postprogram) enrolled in a 24-week behavioral intervention and were exposed to a media campaign. They were compared to cross-sectional survey samples at pre- (n = 245) and postprogram (n = 820) from the media exposed county and a no-intervention county (n = 234 pre, n = 822 post). Women in the behavioral intervention had statistically significant positive changes on physical activity minutes, walking, park and trail use, knowledge of mapped routes and exercise partner, and negative change on exercise self-efficacy. Media exposed women had statistically significant pre- to postprogram differences on knowledge of mapped routes. No-intervention women had significant pre- to postprogram differences on physical activity minutes, walking, and knowledge of mapped routes.

21 CFR 172.410 - Calcium silicate.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Calcium silicate. 172.410 Section 172.410 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Agents § 172.410 Calcium silicate. Calcium silicate, including synthetic calcium silicate, may be safely...

21 CFR 172.410 - Calcium silicate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium silicate. 172.410 Section 172.410 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Agents § 172.410 Calcium silicate. Calcium silicate, including synthetic calcium silicate, may be safely...

21 CFR 172.410 - Calcium silicate.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Calcium silicate. 172.410 Section 172.410 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Agents § 172.410 Calcium silicate. Calcium silicate, including synthetic calcium silicate, may be safely...

21 CFR 172.410 - Calcium silicate.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Calcium silicate. 172.410 Section 172.410 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Agents § 172.410 Calcium silicate. Calcium silicate, including synthetic calcium silicate, may be safely...

21 CFR 172.410 - Calcium silicate.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Calcium silicate. 172.410 Section 172.410 Food and... PERMITTED FOR DIRECT ADDITION TO FOOD FOR HUMAN CONSUMPTION Anticaking Agents § 172.410 Calcium silicate. Calcium silicate, including synthetic calcium silicate, may be safely used in food in accordance with the...

The effect of Low Earth Orbit exposure on some experimental fluorine and silicon-containing polymers

NASA Technical Reports Server (NTRS)

Connell, John W.; Young, Philip R.; Kalil, Carol G.; Chang, Alice C.; Siochi, Emilie J.

1994-01-01

Several experimental fluorine and silicon-containing polymers in film form were exposed to low Earth orbit (LEO) on a Space Shuttle flight experiment (STS-46, Evaluation of Oxygen Interaction with Materials, EOIM-3). The environmental parameters of primary concern were atomic oxygen (AO) and ultraviolet (UV) radiation. The materials were exposed to 2.3 plus or minus 0.1 x 10(exp 20) oxygen atoms/sq cm and 30.6 UV sun hours during the flight. In some cases, the samples were exposed at ambient, 120 C and 200 C. The effects of exposure on these materials were assessed utilizing a variety of characterization techniques including optical, scanning electron (SEM) and scanning tunneling (STM) microscopy, UV-visible (UV-VIS) transmission, diffuse reflectance infrared (DR-FTIR), x-ray photoelectron (XPS) spectroscopy, and in a few cases, gel permeation chromatography (GPC). In addition, weight losses of the films, presumably due to AO erosion, were measured. The fluorine-containing polymers exhibited significant AO erosion and exposed films were diffuse or 'frosted' in appearance and consequently displayed dramatic reductions in optical transmission. The silicon-containing films exhibited minimum AO erosion and the optical transmission of exposed films was essentially unchanged. The silicon near the exposed surface in the films was converted to silicate/silicon oxide upon AO exposure which subsequently provided protection for the underlying material. The silicon-containing epoxies are potentially useful as AO resistant coatings and matrix resins as they are readily processed into carbon fiber reinforced composites and cured via electron radiation.

Geologic map of the southern Funeral Mountains including nearby groundwater discharge sites in Death Valley National Park, California and Nevada

USGS Publications Warehouse

Fridrich, C.J.; Thompson, R.A.; Slate, J.L.; Berry, M.E.; Machette, M.N.

2012-01-01

This 1:50,000-scale geologic map covers the southern part of the Funeral Mountains, and adjoining parts of four structural basins—Furnace Creek, Amargosa Valley, Opera House, and central Death Valley—in California and Nevada. It extends over three full 7.5-minute quadrangles, and parts of eleven others—an area of about 1,000 square kilometers (km2). The boundaries of this map were drawn to include all of the known proximal hydrogeologic features that may affect the flow of groundwater that discharges from springs of the Furnace Creek basin, in the west-central part of the map. These springs provide the main potable water supply for Death Valley National Park. Major hydrogeologic features shown on this map include: (1) springs of the Furnace Creek basin, (2) a large Pleistocene groundwater discharge mound in the northeastern part of the map, (3) the exposed extent of limestones and dolomites that constitute the Paleozoic carbonate aquifer, and (4) the exposed extent of the alluvial conglomerates that constitute the Funeral Formation aquifer.

Biological and therapeutic effects of ortho-silicic acid and some ortho-silicic acid-releasing compounds: New perspectives for therapy.

PubMed

Jurkić, Lela Munjas; Cepanec, Ivica; Pavelić, Sandra Kraljević; Pavelić, Krešimir

2013-01-08

Silicon (Si) is the most abundant element present in the Earth's crust besides oxygen. However, the exact biological roles of silicon remain unknown. Moreover, the ortho-silicic acid (H4SiO4), as a major form of bioavailable silicon for both humans and animals, has not been given adequate attention so far. Silicon has already been associated with bone mineralization, collagen synthesis, skin, hair and nails health atherosclerosis, Alzheimer disease, immune system enhancement, and with some other disorders or pharmacological effects. Beside the ortho-silicic acid and its stabilized formulations such as choline chloride-stabilized ortho-silicic acid and sodium or potassium silicates (e.g. M2SiO3; M= Na,K), the most important sources that release ortho-silicic acid as a bioavailable form of silicon are: colloidal silicic acid (hydrated silica gel), silica gel (amorphous silicon dioxide), and zeolites. Although all these compounds are characterized by substantial water insolubility, they release small, but significant, equilibrium concentration of ortho-silicic acid (H4SiO4) in contact with water and physiological fluids. Even though certain pharmacological effects of these compounds might be attributed to specific structural characteristics that result in profound adsorption and absorption properties, they all exhibit similar pharmacological profiles readily comparable to ortho-silicic acid effects. The most unusual ortho-silicic acid-releasing agents are certain types of zeolites, a class of aluminosilicates with well described ion(cation)-exchange properties. Numerous biological activities of some types of zeolites documented so far might probably be attributable to the ortho-silicic acid-releasing property. In this review, we therefore discuss biological and potential therapeutic effects of ortho-silicic acid and ortho-silicic acid -releasing silicon compounds as its major natural sources.

Method 366.0 Determination of Dissolved Silicate in Estuarine and Coastal Watersby Gas Segmented Continuous Flow Colorimetric Analysis

EPA Science Inventory

This method provides a procedure for the determination of dissolved silicate concentration in estuarine and coastal waters. The dissolved silicate is mainly in the form of silicic acid, H SiO , in estuarine and 4 4 coastal waters. All soluble silicate, including colloidal silici...

Degradation of the Adhesive Properties of MD-944 Diode Tape by Simulated Low Earth Orbit Environmental Factors

NASA Technical Reports Server (NTRS)

Albyn, K.; Finckenor, M.

2006-01-01

The International Space Station (ISS) solar arrays utilize MD-944 diode tape with silicone pressure-sensitive adhesive to protect the underlying diodes and also provide a high-emittance surface. On-orbit, the silicone adhesive will be exposed and ultimately convert to a glass-like silicate due to atomic oxygen (AO). The current operational plan is to retract ISS solar array P6 and leave it stored under load for a long duration (6 mo or more). The exposed silicone adhesive must not cause the solar array to stick to itself or cause the solar array to fail during redeployment. The Environmental Effects Branch at Marshall Space Flight Center, under direction from the ISS Program Office Environments Team, performed simulated space environment exposures with 5-eV AO, near ultraviolet radiation and ionizing radiation. The exposed diode tape samples were put under preload and then the resulting blocking force was measured using a tensile test machine. Test results indicate that high-energy AO, ultraviolet radiation, and electron ionizing radiation exposure all reduce the blocking force for a silicone-to-silicone bond. AO exposure produces the most significant reduction in blocking force

Gamma radiation effects on the dynamic fatigue measurements of glass discs

NASA Technical Reports Server (NTRS)

Ananaba, T. O. J.; Kinser, D. L.

1985-01-01

Circular specimens of low iron soda lime silicate glass were blasted with grit after having a circular notch etched into their centers. After separation into two groups, one group was exposed to gamma radiation. The fracture strengths of all samples were then tested by the biaxial technique, i.e., specimens were balanced on three balls and loaded in the center by a piston. The irradiated samples had received a 140,000 Gy dose from a Co-60 source. An enhanced interaction between the ambient moisture and the grit-blasted central notch was observed in the irradiated samples, which displayed accelerated corrosion.

Investigation of the Behavior of Hardening Masonry Exposed to Variable Stresses

PubMed Central

Šlivinskas, Tomas; Jonaitis, Bronius; Marčiukaitis, Jonas Gediminas

2018-01-01

This paper analyzes the behavior of masonry under variable loads during execution (construction stage). It specifies the creep coefficient for calcium silicate brick masonry, presenting the research data of masonry deformation under variable and constant long-term loads. The interaction of separate layers of composite material in masonry is introduced and the formulae for determining long-term deformations are offered. The research results of masonry’s compressive strength and deformation properties under variable and constant long-term loads are presented. These are then compared to calculated ones. According to the presented comparison, the calculated long-term deformations coincide quite well with those determined experimentally. PMID:29710802

Investigation of the Behavior of Hardening Masonry Exposed to Variable Stresses.

PubMed

Šlivinskas, Tomas; Jonaitis, Bronius; Marčiukaitis, Jonas Gediminas; Zavalis, Robertas

2018-04-28

This paper analyzes the behavior of masonry under variable loads during execution (construction stage). It specifies the creep coefficient for calcium silicate brick masonry, presenting the research data of masonry deformation under variable and constant long-term loads. The interaction of separate layers of composite material in masonry is introduced and the formulae for determining long-term deformations are offered. The research results of masonry’s compressive strength and deformation properties under variable and constant long-term loads are presented. These are then compared to calculated ones. According to the presented comparison, the calculated long-term deformations coincide quite well with those determined experimentally.

Evaluation of low cost/high temperature insulation, July 1974 - June 1975

NASA Technical Reports Server (NTRS)

Strauss, E. L.

1975-01-01

Six fiber products and six insulation blankets comprising silica, alumina, zirconia, mullite, and mixed ceramic systems were subjected to furnace exposures up to 500 hours at temperatures of 1000 to 1600 C and evaluated for chemical and dimensional stability and for changes in thermal conductivity. Alumina, zirconia, and mullite fibers were fabricated into reusable surface insulation (RSI) tile by water-felting and reimpregnation with ethyl silicate. Specimens were exposed to 25 thermal cycles at 1200 C and 1400 C and a pressure of 10 and 32 torr, respectively. Production costs for 930 sq m (10,000 sq ft) of blanket insulation and of alumina RSI tile were developed.

Anti-reflection coatings on large area glass sheets

NASA Technical Reports Server (NTRS)

Pastirik, E.

1980-01-01

Antireflective coatings which may be suitable for use on the covers of photovoltaic solar modules can be easily produced by a dipping process. The coatings are applied to glass by drawing sheets of glass vertically out of dilute aqueous sodium silicate solutions at a constant speed, allowing the adherent liquid film to dry, then exposing the dried film to concentrated sulfuric acid, followed by a water rinse and dry. The process produces coatings of good optical performance (96.7 percent peak transmission at 0.540 mu M wavelength) combined with excellent stain and soil resistance, and good resistance to abrasion. The process is reproduceable and easily controlled.

Barrier Properties of Layered-Silicate Reinforced Ethylenepropylenediene Monomer/Chloroprene Rubber Nanorubbers.

PubMed

Wu, Chang Mou; Hsieh, Wen Yen; Cheng, Kuo Bin; Lai, Chiu-Chun; Lee, Kuei Chi

2018-05-09

The triacetin and nitroglycerin barrier properties of layered-silicate reinforced ethylenepropylenediene monomer/chloroprene rubber (EPDM/CR) nanorubbers were investigated as rocket-propellant inhibitors. EPDM/CR nanorubbers with intercalated structures were formulated and prepared by the melt-compounding method. The triacetin permeability and nitroglycerin absorption were observed to decrease with increasing layered-silicate content. The layered silicates also improved the flame retardancies of the nanorubbers by forming silicate reinforced carbonaceous chars. Layered-silicate reinforced EPDM/CR nanorubbers are potentially effective rocket propellant-inhibiting materials.

The role of disseminated calcite in the chemical weathering of granitoid rocks

USGS Publications Warehouse

White, A.F.; Bullen, T.D.; Vivit, D.V.; Schulz, M.S.; Clow, D.W.

1999-01-01

Accessory calcite, present at concentrations between 300 and 3000 mg kg-1, occurs in fresh granitoid rocks sampled from the Merced watershed in Yosemite National Park, CA, USA; Loch Vale in Rocky Mountain National Park CO USA; the Panola watershed, GA USA; and the Rio Icacos, Puerto Rico. Calcite occurs as fillings in microfractures, as disseminated grains within the silicate matrix, and as replacement of calcic cores in plagioclase. Flow-through column experiments, using de-ionized water saturated with 0.05 atm. CO2, produced effluents from the fresh granitoid rocks that were dominated by Ca and bicarbonate and thermodynamically saturated with calcite. During reactions up to 1.7 yr, calcite dissolution progressively decreased and was superceded by steady state dissolution of silicates, principally biotite. Mass balance calculations indicate that most calcite had been removed during this time and accounted for 57-98% of the total Ca released from these rocks. Experimental effluents from surfically weathered granitoids from the same watersheds were consistently dominated by silicate dissolution. The lack of excess Ca and alkalinity indicated that calcite had been previously removed by natural weathering. The extent of Ca enrichment in watershed discharge fluxes corresponds to the amounts of calcite exposed in granitoid rocks. High Ca/Na ratios relative to plagioclase stoichiometries indicate excess Ca in the Yosemite, Loch Vale, and other alpine watersheds in the Sierra Nevada and Rocky Mountains of the western United States. This Ca enrichment correlates with strong preferential weathering of calcite relative to plagioclase in exfoliated granitoids in glaciated terrains. In contrast, Ca/Na flux ratios are comparable to or less than the Ca/Na ratios for plagioclase in the subtropical Panola and tropical Rio Icacos watersheds, in which deeply weathered regoliths exhibit concurrent losses of calcite and much larger masses of plagioclase during transport-limited weathering. These results indicate that the weathering of accessory calcite may strongly influence Ca and alkalinity fluxes from silicate rocks during and following periods of glaciation and tectonism but is much less important for older stable geomorphic surfaces.

Protein Kinase G Induces an Immune Response in Cows Exposed to Mycobacterium avium Subsp. paratuberculosis

PubMed Central

Bach, Eviatar; Chaffer, Marcelo; Lai, Wanika; Keefe, Greg; Begg, Douglas J.

2018-01-01

To establish infection, pathogens secrete virulence factors, such as protein kinases and phosphatases, to modulate the signal transduction pathways used by host cells to initiate immune response. The protein MAP3893c is annotated in the genome sequence of Mycobacterium avium subspecies paratuberculosis (MAP), the causative agent of Johne's disease, as the serine/threonine protein kinase G (PknG). In this work, we report that PknG is a functional kinase that is secreted within macrophages at early stages of infection. The antigen is able to induce an immune response from cattle exposed to MAP in the form of interferon gamma production after stimulation of whole blood with PknG. These findings suggest that PknG may contribute to the pathogenesis of MAP by phosphorylating macrophage signalling and/or adaptor molecules as observed with other pathogenic mycobacterial species. PMID:29581962

Protein Kinase G Induces an Immune Response in Cows Exposed to Mycobacterium avium Subsp. paratuberculosis.

PubMed

Bach, Horacio; Richard-Greenblatt, Melissa; Bach, Eviatar; Chaffer, Marcelo; Lai, Wanika; Keefe, Greg; Begg, Douglas J

2018-01-01

To establish infection, pathogens secrete virulence factors, such as protein kinases and phosphatases, to modulate the signal transduction pathways used by host cells to initiate immune response. The protein MAP3893c is annotated in the genome sequence of Mycobacterium avium subspecies paratuberculosis (MAP), the causative agent of Johne's disease, as the serine/threonine protein kinase G (PknG). In this work, we report that PknG is a functional kinase that is secreted within macrophages at early stages of infection. The antigen is able to induce an immune response from cattle exposed to MAP in the form of interferon gamma production after stimulation of whole blood with PknG. These findings suggest that PknG may contribute to the pathogenesis of MAP by phosphorylating macrophage signalling and/or adaptor molecules as observed with other pathogenic mycobacterial species.

Raining a magma ocean: Thermodynamics of rocky planets after a giant impact

NASA Astrophysics Data System (ADS)

Stewart, S. T.; Lock, S. J.; Caracas, R.

2017-12-01

Rocky planets in exoplanetary systems have equilibrium temperatures up to a few 1000 K. The thermal evolution after a giant impact is sensitive to the equilibrium temperature. Post-impact rocky bodies are thermally stratified, with cooler, lower-entropy silicate overlain by vaporized, higher-entropy silicate. The radii of impact-vaporized rocky planets are much larger than the radii of equivalent condensed bodies. Furthermore, after some high-energy, high-angular momentum collisions, the post-impact body exceeds the corotation limit for a rocky planet and forms a synestia. Initially, volatiles and silicates are miscible at the high temperatures of the outer layer. If the equilibrium temperature with the star is lower than the silicate condensation temperature ( 2000 K), silicate droplets form at the photosphere and fall while volatile components remain in the vapor. Radiation and turbulent convection cool the vapor outer layer to the silicate vapor curve. A distinct magma ocean forms as the thermal profile crosses the silicate vapor curve and the critical curves for the volatiles. Near the temperatures and pressures of the critical curves, volatiles and silicates are partially soluble in each other. As the system continues cooling, the volatile vapor and silicate liquid separate toward the end member compositions, which are determined by the equilibrium temperature and the total vapor pressure of volatiles. If the equilibrium temperature with the star is near or above the condensation temperature for silicates, there would be limited condensation at the photosphere. Initially, the cooler lower mantle would slowly, diffusively equilibrate with the hotter upper mantle. In some cases, the thermal profile may cross the silicate vapor curve in the middle of the silicate layer, producing a silicate rain layer within the body. With continued evolution toward an adiabatic thermal profile, the body would separate into a silicate liquid layer underlying a silicate-volatile vapor layer. As the hottest rocky planets become tidally locked to their star, cooling progresses asymmetrically. The timing and degree of differentiation of rocky planets into silicate mantles and volatile atmospheres depends on the thermal evolution of vaporized rocky planets and may vary widely with equilibrium temperature.

Transmission Electron Microscope Studies of Martian 'Iddingsite' in the Nakhlite Meteorite MIL 090032

NASA Astrophysics Data System (ADS)

Hallis, L.; Ishii, H.; Bradley, J. P.; Taylor, J.

2012-12-01

As with the other nakhlites, MIL 090032 contains iddingsite-like alteration veins in the olivine phenocrysts that reportedly originated on Mars[1]. These 'iddingsite' veins have been analysed in a number of the nakhlite meteorites[2], and the presence of hydrous silicate gel, smectite clays, siderite, Fe-oxides, gypsum and carbonate have been reported. The presence and proportion of these phases in the different nakhlites appears to relate to the composition and concentration of the martian brine that flowed through each, thus supporting the theory that the nakhlite secondary alteration phases were produced by an evaporation sequence on the surface of Mars[3]. We analyzed these martian 'iddingsite' veins in MIL 090032 with the aim of placing it and its three paired meteorites within the nakhlite alteration sequence. By expanding our knowledge of this alteration sequence, we will gain extra insight into the conditions on the martian surface at the time these 'iddingsite' veins formed (<1.3 Ga). We utilized the 80-300 kV aberration-corrected FEI Titan (Scanning) Transmission Electron Microscope (S-TEM) system at Lawrence Livermore National Laboratory to analyse a ~15×8μm Focused Ion Beam (FIB) section of an 'iddingsite' vein in MIL 090032. To allow the electrons to be transmitted through the FIB section, it was milled down to ~150 nm thickness. Our initial TEM data indicate this FIB section contains hydrous amorphous silicate gel towards the center, with areas of phyllosilicate (possibly nontronite) interspersed within this central zone. Towards the outer edge of the vein jarosite and then gypsum sulfates were present. At the very edge only partially broken down olivine was observed. The presence of phyllosilicate and silicate gel in this vein suggests the 'iddingsite' in MIL 090032 was produced by water-rich brine, and the abundance of sulfates suggests the brine was enriched in sulfur. This assemblage of minerals is most in line with that of the 'iddingsite' veins in the meteorite Lafayette, which is thought to have been exposed to the most aqueous brine in the nakhlite alteration sequence[2,3]. MIL 090032 is a meteorite find, and contains areas of terrestrially derived sulfate-rich alteration which appear to have similar compositions to the martian 'iddingsite' veins (although texturally the two are easily distinguishable). Therefore, in addition to our analysis of the above 'iddignsite' FIB section, we aim to analyze a similar FIB section of this terrestrial sulfate-rich alteration and compare the two. This comparison could not only determine if terrestrial weathering has affected the mineralogy and petrology of the pre-terrestrial alteration, but also whether the conditions on the martian surface were similar to those in the Antarctic valleys at the time the 'iddingsite' veins formed. [1]Gooding et al. (1991) Meteoritics 26, 135-143. [2]Changela and Bridges (2011) MAPS 45, 1847-1867. [3]Bridges et al. (2001) Space Sci. Rev. 96, 365-392.

Voluminous low δ18O magmas in the late Miocene Heise volcanic field, Idaho: Implications for the fate of Yellowstone hotspot calderas

USGS Publications Warehouse

Bindeman, I.N.; Watts, K.E.; Schmitt, A.K.; Morgan, L.A.; Shanks, P.W.C.

2007-01-01

We report oxygen isotope compositions of phenocrysts and U-Pb ages of zircons in four large caldera-forming ignimbrites and post-caldera lavas of the Heise volcanic field, a nested caldera complex in the Snake River Plain, that preceded volcanism in Yellowstone. Early eruption of three normal δ18O voluminous ignimbrites with δ18Oquartz = 6.4‰ and δ18Ozircon = 4.8‰ started at Heise at 6.6 Ma, and was followed by a 2‰–3‰ δ18O depletion in the subsequent 4.45 Ma Kilgore caldera cycle that includes the 1800 km3 Kilgore ignimbrite, and post-Kilgore intracaldera lavas with δ18Oquartz = 4.3‰ and δ18Ozircon = 1.5‰. The Kilgore ignimbrite represents the largest known low-δ18O magma in the Snake River Plain and worldwide. The post-Kilgore low δ18O volcanism likely represents the waning stages of silicic magmatism at Heise, prior to the reinitiation of normal δ18O silicic volcanism 100 km to the northeast at Yellowstone. The occurrence of low δ18O magmas at Heise and Yellowstone hallmarks a mature stage of individual volcanic cycles in each caldera complex. Sudden shifts in δ18O of silicic magmas erupted from the same nested caldera complexes argue against any inheritance of the low δ18O signature from mantle or crustal sources. Instead, δ18O age trends indicate progressive remelting of low δ18O hydrothermally altered intracaldera rocks of previous eruptions. This trend may be generally applicable to older caldera complexes in the Snake River Plain that are poorly exposed.

Effect of temperature on hydration kinetics and polymerization of tricalcium silicate in stirred suspensions of CaO-saturated solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grant, Steven A.; Boitnott, Ginger E.; Korhonen, Charles J.

2006-04-15

Tricalcium silicate was hydrated at 274, 278, 283, 298, and 313 K in stirred suspensions of saturated CaO solutions under a nitrogen-gas atmosphere until the end of deceleratory period. The suspension conductivities and energy flows were measured continuously. The individual reaction rates for tricalcium silicate dissolution, calcium silicate hydrate precipitation, and calcium hydroxide precipitation were calculated from these measurements. The results suggest that the proportion of tricalcium silicate dissolved was determined by the rate of tricalcium silicate dissolution and the time to very rapid calcium hydroxide precipitation. The time to very rapid calcium hydroxide precipitation was more sensitive to changesmore » in temperature than was the rate of tricalcium silicate dissolution, so that the proportion of tricalcium silicate hydration dissolved by the deceleratory period increased with decreasing temperature. The average chain length of the calcium silicate hydrate ascertained by magic-angle spinning nuclear magnetic resonance spectroscopy increased with increasing temperature.« less

Kinematics and age of Early Tertiary trench parallel volcano-tectonic lineaments in southern Mexico: Tectonic implications

NASA Astrophysics Data System (ADS)

Martini, M.; Ferrari, L.; Lopez Martinez, M.; Cerca Martinez, M.; Serrano Duran, L.

2007-05-01

We present new geological, structural, and geochronological data that constrain the timing and geometry of Early Tertiary strike slip deformation in southwestern Mexico and its relation with the concurrent magmatic activity. Geologic mapping in Guerrero and Michoacan States documented two regional WNW trending volcano-tectonic lineaments sub parallel to the present trench. The southernmost lineament runs for ~140 km from San Miguel Totolapan area (NW Guerrero) to Sanchiqueo (SE Michoacan), and passes through Ciudad Altamirano. Its southeastern part is marked by the alignment of at least eleven silicic to intermediate major domes as well as by the course of the Balsas River. The northwestern part of the lineament is characterized by ductile left lateral shear zones in Early Tertiary plutonic rocks observed in the Rio Chiquito valley. Domes near Ciudad Altamirano are unaffected by ductile shearing and yielded a ~42 Ma 40Ar/39Ar age, setting a minimum age for this deformation. The northern volcano-tectonic lineament runs for ~190 km between the areas of Huitzuco in northern Guerrero and the southern part of the Tzitzio fold in eastern Michoacan. The Huautla, Tilzapotla, Taxco, La Goleta and Nanchititla silicic centers (all in the range 37-34 Ma) are emplaced along this lineament, which continues to the WNW trough a mafic dike swarm exposed north of Tiquicheo (37-35 Ma) and the Purungueo subvolcanic body (~42 Ma). These rocks, unaffected by ductile shearing, give a minimum age of deformation similar to the southern Totolapan-Sanquicheo lineament. Post ~42 Ma deformation is essentially brittle and is characterized by several left lateral and right lateral transcurrent faults with typical Riedel patterns. Other trench-parallel left lateral shear zones active in pre-Oligocene times were recently reported in western Oaxaca. The recognizing of Early Tertiary trench-parallel and left-lateral ductile shearing in internal areas of southern Mexico suggest a field of widely distributed flow and shear zones with relatively small individual displacement that might represent an immature stage of the developing North American-Caribbean plate boundary. The documented transition from ductile to brittle deformation and the localization of shearing and volcanism in the Late Eocene may be related to the focusing of inter-plate deformation in a discrete left lateral transcurrent North America-Caribbean boundary. The opening of the Cayman Through at ~49 Ma may have accelerated this process.

A new global interior ocean mapped climatology: the 1° × 1° GLODAP version 2

NASA Astrophysics Data System (ADS)

Lauvset, Siv K.; Key, Robert M.; Olsen, Are; van Heuven, Steven; Velo, Anton; Lin, Xiaohua; Schirnick, Carsten; Kozyr, Alex; Tanhua, Toste; Hoppema, Mario; Jutterström, Sara; Steinfeldt, Reiner; Jeansson, Emil; Ishii, Masao; Perez, Fiz F.; Suzuki, Toru; Watelet, Sylvain

2016-08-01

We present a mapped climatology (GLODAPv2.2016b) of ocean biogeochemical variables based on the new GLODAP version 2 data product (Olsen et al., 2016; Key et al., 2015), which covers all ocean basins over the years 1972 to 2013. The quality-controlled and internally consistent GLODAPv2 was used to create global 1° × 1° mapped climatologies of salinity, temperature, oxygen, nitrate, phosphate, silicate, total dissolved inorganic carbon (TCO2), total alkalinity (TAlk), pH, and CaCO3 saturation states using the Data-Interpolating Variational Analysis (DIVA) mapping method. Improving on maps based on an earlier but similar dataset, GLODAPv1.1, this climatology also covers the Arctic Ocean. Climatologies were created for 33 standard depth surfaces. The conceivably confounding temporal trends in TCO2 and pH due to anthropogenic influence were removed prior to mapping by normalizing these data to the year 2002 using first-order calculations of anthropogenic carbon accumulation rates. We additionally provide maps of accumulated anthropogenic carbon in the year 2002 and of preindustrial TCO2. For all parameters, all data from the full 1972-2013 period were used, including data that did not receive full secondary quality control. The GLODAPv2.2016b global 1° × 1° mapped climatologies, including error fields and ancillary information, are available at the GLODAPv2 web page at the Carbon Dioxide Information Analysis Center (CDIAC; doi:10.3334/CDIAC/OTG.NDP093_GLODAPv2).

Regional geology mapping using satellite-based remote sensing approach in Northern Victoria Land, Antarctica

NASA Astrophysics Data System (ADS)

Pour, Amin Beiranvand; Park, Yongcheol; Park, Tae-Yoon S.; Hong, Jong Kuk; Hashim, Mazlan; Woo, Jusun; Ayoobi, Iman

2018-06-01

Satellite remote sensing imagery is especially useful for geological investigations in Antarctica because of its remoteness and extreme environmental conditions that constrain direct geological survey. The highest percentage of exposed rocks and soils in Antarctica occurs in Northern Victoria Land (NVL). Exposed Rocks in NVL were part of the paleo-Pacific margin of East Gondwana during the Paleozoic time. This investigation provides a satellite-based remote sensing approach for regional geological mapping in the NVL, Antarctica. Landsat-8 and the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) datasets were used to extract lithological-structural and mineralogical information. Several spectral-band ratio indices were developed using Landsat-8 and ASTER bands and proposed for Antarctic environments to map spectral signatures of snow/ice, iron oxide/hydroxide minerals, Al-OH-bearing and Fe, Mg-OH and CO3 mineral zones, and quartz-rich felsic and mafic-to-ultramafic lithological units. The spectral-band ratio indices were tested and implemented to Level 1 terrain-corrected (L1T) products of Landsat-8 and ASTER datasets covering the NVL. The surface distribution of the mineral assemblages was mapped using the spectral-band ratio indices and verified by geological expeditions and laboratory analysis. Resultant image maps derived from spectral-band ratio indices that developed in this study are fairly accurate and correspond well with existing geological maps of the NVL. The spectral-band ratio indices developed in this study are especially useful for geological investigations in inaccessible locations and poorly exposed lithological units in Antarctica environments.

Steam based conversion coating on AA6060 alloy: Effect of sodium silicate chemistry and corrosion performance

NASA Astrophysics Data System (ADS)

Din, Rameez Ud; Bordo, Kirill; Tabrizian, Naja; Jellesen, Morten Stendahl; Ambat, Rajan

2017-11-01

Surface treatment of aluminium alloy AA6060 using an industrially applicable pilot steam jet system with and without silicate chemistry has been investigated. Treatment using steam alone and steam with silicate, resulted in an oxide layer formation with thickness ∼425 nm and ∼160 nm, respectively. Moreover, the use of sodium silicate resulted in the formation of distinct microstructure and incorporation of silicate into the oxide film. These oxide films reduced the anodic activity 4 times, while the corrosion protection by silicate containing oxide was the function of its concentration. Further, in acid salt spray and filiform corrosion tests, oxide layer containing silicate exhibited two times higher corrosion resistance.

Acute eosinophilic pneumonia in a New York City firefighter exposed to World Trade Center dust.

PubMed

Rom, William N; Weiden, Michael; Garcia, Roberto; Yie, Ting An; Vathesatogkit, Pratan; Tse, Doris B; McGuinness, Georgeann; Roggli, Victor; Prezant, David

2002-09-15

We report a sentinel case of acute eosinophilic pneumonia in a firefighter exposed to high concentrations of World Trade Center dust during the rescue effort from September 11 to 24. The firefighter presented with a Pa(O2) of 53 mm Hg and responded to oxygen and corticosteroids. Computed tomography scan showed patchy ground glass density, thickened bronchial walls, and bilateral pleural effusions. Bronchoalveolar lavage recovered 70% eosinophils, with only 1% eosinophils in peripheral blood. Eosinophils were not degranulated and increased levels of interleukin-5 were measured in bronchoalveolar lavage and serum. Mineralogic analysis counted 305 commercial asbestos fibers/10(6) macrophages including those with high aspect ratios, and significant quantities of fly ash and degraded fibrous glass. Acute eosinophilic pneumonia is a rare consequence of acute high dust exposure. World Trade Center dust consists of large particle-size silicates, but fly ash and asbestos fibers may be found in bronchoalveolar lavage cells.

Locations of Ice-Exposing Fresh Craters on Mars

NASA Image and Video Library

2013-12-10

This map of Mars indicates locations of new craters that have excavated ice blue and those that have not red. Albedo information comes from NASA Mars Odyssey orbiter, and the map comes from NASA Mars Global Surveyor orbiter.

Barrier Properties of Layered-Silicate Reinforced Ethylenepropylenediene Monomer/Chloroprene Rubber Nanorubbers

PubMed Central

Hsieh, Wen Yen; Cheng, Kuo Bin; Lai, Chiu-Chun; Lee, Kuei Chi

2018-01-01

The triacetin and nitroglycerin barrier properties of layered-silicate reinforced ethylenepropylenediene monomer/chloroprene rubber (EPDM/CR) nanorubbers were investigated as rocket-propellant inhibitors. EPDM/CR nanorubbers with intercalated structures were formulated and prepared by the melt-compounding method. The triacetin permeability and nitroglycerin absorption were observed to decrease with increasing layered-silicate content. The layered silicates also improved the flame retardancies of the nanorubbers by forming silicate reinforced carbonaceous chars. Layered-silicate reinforced EPDM/CR nanorubbers are potentially effective rocket propellant-inhibiting materials. PMID:29747427

Building Interoperable FHIR-Based Vocabulary Mapping Services: A Case Study of OHDSI Vocabularies and Mappings.

PubMed

Jiang, Guoqian; Kiefer, Richard; Prud'hommeaux, Eric; Solbrig, Harold R

2017-01-01

The OHDSI Common Data Model (CDM) is a deep information model, in which its vocabulary component plays a critical role in enabling consistent coding and query of clinical data. The objective of the study is to create methods and tools to expose the OHDSI vocabularies and mappings as the vocabulary mapping services using two HL7 FHIR core terminology resources ConceptMap and ValueSet. We discuss the benefits and challenges in building the FHIR-based terminology services.

A close-range photogrammetric technique for mapping neotectonic features in trenches

USGS Publications Warehouse

Fairer, G.M.; Whitney, J.W.; Coe, J.A.

1989-01-01

Close-range photogrammetric techniques and newly available computerized plotting equipment were used to map exploratory trench walls that expose Quaternary faults in the vicinity of Yucca Mountain, Nevada. Small-scale structural, lithologic, and stratigraphic features can be rapidly mapped by the photogrammetric method. This method is more accurate and significantly more rapid than conventional trench-mapping methods, and the analytical plotter is capable of producing cartographic definition of high resolution when detailed trench maps are necessary. -from Authors

Digital Geologic Map Database of Medicine Lake Volcano, Northern California

NASA Astrophysics Data System (ADS)

Ramsey, D. W.; Donnelly-Nolan, J. M.; Felger, T. J.

2010-12-01

Medicine Lake volcano, located in the southern Cascades ~55 km east-northeast of Mount Shasta, is a large rear-arc, shield-shaped volcano with an eruptive history spanning nearly 500 k.y. Geologic mapping of Medicine Lake volcano has been digitally compiled as a spatial database in ArcGIS. Within the database, coverage feature classes have been created representing geologic lines (contacts, faults, lava tubes, etc.), geologic unit polygons, and volcanic vent location points. The database can be queried to determine the spatial distributions of different rock types, geologic units, and other geologic and geomorphic features. These data, in turn, can be used to better understand the evolution, growth, and potential hazards of this large, rear-arc Cascades volcano. Queries of the database reveal that the total area covered by lavas of Medicine Lake volcano, which range in composition from basalt through rhyolite, is about 2,200 km2, encompassing all or parts of 27 U.S. Geological Survey 1:24,000-scale topographic quadrangles. The maximum extent of these lavas is about 80 km north-south by 45 km east-west. Occupying the center of Medicine Lake volcano is a 7 km by 12 km summit caldera in which nestles its namesake, Medicine Lake. The flanks of the volcano, which are dotted with cinder cones, slope gently upward to the caldera rim, which reaches an elevation of nearly 2,440 m. Approximately 250 geologic units have been mapped, only half a dozen of which are thin surficial units such as alluvium. These volcanic units mostly represent eruptive events, each commonly including a vent (dome, cinder cone, spatter cone, etc.) and its associated lava flow. Some cinder cones have not been matched to lava flows, as the corresponding flows are probably buried, and some flows cannot be correlated with vents. The largest individual units on the map are all basaltic in composition, including the late Pleistocene basalt of Yellowjacket Butte (296 km2 exposed), the largest unit on the map, whose area is partly covered by a late Holocene andesite flow. Silicic lava flows are mostly confined to the main edifice of the volcano, with the youngest rhyolite flows found in and near the summit caldera, including the rhyolitic Little Glass Mountain (~1,000 yr B.P.) and Glass Mountain (~950 yr B.P.) flows, which are the youngest eruptions at Medicine Lake volcano. In postglacial time, 17 eruptions have added approximately 7.5 km3 to the volcano’s total estimated volume of 600 km3, which may be the largest by volume among Cascade Range volcanoes. The volcano has erupted nine times in the past 5,200 years, a rate more frequent than has been documented at all other Cascade volcanoes except Mount St. Helens.

Solubility of copper in silicate melts as function of oxygen and sulfur fugacities, temperature, and silicate composition

NASA Astrophysics Data System (ADS)

Holzheid, A.; Lodders, K.

2001-06-01

The solubility of Cu in silicate melts coexisting with liquid Cu(Fe) metal and liquid Cu(Fe) sulfide was determined experimentally at oxygen fugacities ranging from 10 -9.1 to 10 -13.6 bar and sulfur fugacities ranging from 10 -2.5 to 10 -6.3 bar at 1300°C. An iron oxide-free silicate of anorthite-diopside eutectic composition and a synthetic MgO-rich basaltic silicate (FeO-bearing) were used in the partitioning experiments. In S-containing systems, some of the metal reacted to metal sulfide. The silicates in the four systems investigated (Fe-free and S-free; Fe-containing and S-free; Fe-free and S-containing; Fe-containing and S-containing) had different colors depending on the dissolved Cu species and the presence of iron and/or sulfur. Irrespective of the presence of sulfur, the solubility of Cu in the silicate increases with increasing oxygen fugacity and metal/silicate partition coefficients for Cu decrease. Increasing the temperature from 1300°C to 1514°C increases the Cu solubility (decreases the metal/silicate partition coefficient) at an oxygen fugacity 0.5 log units below the iron-wüstite (IW) equilibrium in the Fe-free, S-free and Fe-containing, S-free systems. We infer the presence of monovalent Cu + ("CuO 0.5") in the silicate melt on the basis of the solubility of Cu as function of oxygen fugacity. Experiments containing iron yield a formal valence of ˜0.5 for Cu at very low oxygen fugacities, which is not observed in Fe-free systems. The low formal valence is explained by redox reactions between iron and copper in the silicate melts. There is no evidence for sulfidic dissolution of Cu in the silicates but sulfur has indirect effects on Cu partitioning. Iron metal/silicate partition coefficients depend on oxygen fugacity and on sulfur fugacity. Sulfidic dissolution of iron and oxide-sulfide exchange reactions with Cu cause a small increase in Cu metal/silicate partition coefficients. We derive an activity coefficient (γ CuO 0.5) of 10 ± 1 for liquid CuO 0.5 at 1300°C for the silicate melts used here. A comparison with literature data shows that log γ CuO 0.5 increases in proportion to the mass percentages [CaO +(Al 2O 3)/2] in silicate melts. We recommend the following equations for Cu metal/silicate and sulfide/silicate partitioning for geochemical and cosmochemical modeling if silicate composition and the activity of Cu in the metal or sulfide is known: log D met/sil = -0.48 - 0.25 · log fO 2 - log γ Cu metal + 0.02 · [CaO + (Al 2O 3)/2; wt%] silicate logD sul/sil=+0.76-0.25 · logfO 2+0.25logfS 2-logγ CS 0.5,sulfide +0.02 · [CaO+Al 2O 3/2;wt%] silicate. The derived Cu metal/silicate and metal/sulfide partition coefficients are applied to core formation in the Earth and Mars. The observed Cu abundances in the Earth cannot be easily explained by simple core-mantle equilibrium, but the observed Cu abundances for Mars are consistent with core-mantle equilibrium at low pressure and temperatures.

EFFECT OF SILICATE ON GRAM STAINING AND VIABILITY OF PNEUMOCOCCI AND OTHER BACTERIA

PubMed Central

MacLeod, Colin M.; Roe, Amy S.

1956-01-01

Application of silicate solutions to living or heat-killed pneumococci and to certain "viridans" streptococci causes their conversion from a Gram-positive to a Gram-negative state. The original staining properties can be restored by suspending the silicate-treated bacteria in alkaline solutions of various salts but not by simple washing in water. Living pneumococci and the strains of streptococci whose staining properties are similarly affected are killed when suspended in silicate solutions. In other Gram-positive species silicate causes conversion to Gram negativity but restoration to positivity occurs upon washing in water. In a third group of Gram-positive organisms silicate has no effect on the Gram reaction. The viability of organisms in these two groups is unaffected by silicate under the conditions employed. No effect on staining or viability of Gram-negative bacteria has been observed. The effects of silicate on staining and viability are inhibited by nutrient broth or whole serum but not by purified serum albumin. Lecithin, choline, and other substituted ammonium compounds also inhibit the effects of silicate on pneumococci. PMID:13306854

Rhenium - osmium heterogeneity of enriched mantle basalts explained by composition and behaviour of mantle-derived sulfides

NASA Astrophysics Data System (ADS)

Harvey, J.; Dale, C. W.; Gannoun, A.; Burton, K. W.

2010-12-01

Analyses of enriched mantle (EM) -basalts, using lithophile element-based isotope systems have long provided evidence for discrete, but variable mantle reservoirs [1]. Upon partial melting, the isotopic fingerprint of each reservoir is imparted upon the partial melt produced. However, recent work involving the Re-Os isotope systematics of EM-basalts [2] suggests that it may not be so simple to delimit these previously well defined mantle reservoirs; the “mantle zoo” [3] may contain more reservoirs than previously envisaged. However, a simple model, with varying contributions from two populations of compositionally distinct mantle sulfides can readily account for the observed heterogeneities in Re-Os isotope systematics of such basalts without additional mantle reservoirs. Rhenium-osmium elemental and isotopic analyses of individual sulfide grains separated from spinel lherzolites from Kilbourne Hole, NM, USA demonstrate that two discrete populations of mantle sulfide exist in terms of both Re-Os systematics and textural relationship with co-existing silicates. One population, with a rounded morphology, is preserved in silicate grains and typically possesses high [Os], low [Re] with unradiogenic, typically sub-chondritic, 187Os/188Os attributable to long term isolation in a low-Re environment. By contrast, irregular-shaped sulfides, preserved along silicate grain boundaries, possess low [Os], higher [Re] and a wider range of, but generally supra-chondritic, 187Os/188Os ([Os] typically ≤ 1-2 ppm, 187Os/188Os ≤ 0.3729; this study). This population is thought to represent metasomatic sulfide (e.g. [4,5]). Uncontaminated silicate phases contain negligible Os (<100 ppt) therefore the Os elemental and isotope composition of basalts is dominated by volumetrically insignificant sulfide ([Os] ≤ 37 ppm, this study). During the early stages of partial melting, supra-chondritic interstitial sulfides are mobilized and incorporated into the melt, adding their radiogenic 187Os/188Os signature. Only when sulfides armored within silicates are exposed to the melt through continued partial melting will enclosed sulfides add their high [Os] and unradiogenic 187Os/188Os to the aggregate melt. Platinum-group element data for whole rocks are also consistent with this scenario. The sequence of (i) addition of all the metasomatic sulfide, followed by (ii) the incorporation of small amounts of armored sulfide can thus account for the range of both [Os] and 187Os/188Os of EM-basalts worldwide without the need for contributions from additional silicate mantle reservoirs. References: [1] Zindler & Hart, (1986) Annu. Rev. Earth Planet. Sci. 14, 493-571. [2] Class et al. (2009) Earth Planet. Sci. Lett. 284, 219-227. [3] Stracke, et al. (2005) Geochem., Geophys., Geosys. 6, doi:10.1029/2004GC000824. [4] Burton et al., Earth Planet. Sci. Lett. (1999) 172, 311-322. [5] Alard et al., (2002) Earth Planet. Sci. Lett. 203, 651-663

The effect of thermal and organic additive in morphology of ceramic based silicate

NASA Astrophysics Data System (ADS)

Ginting, J.; Bangun, N.; Sembiring, H. Br; Putri, N. K.

2017-04-01

M-Silicate (M = Mg, Ca) has been prepared by exchange metal reaction from M-Chloride salts and sodium silicate. The resulting white solid of chloride salts then heated at 700, 800, 900 and 1000 °C. Due to increase the porosity of M-Silicate, 1,2-propanediol, oleic acid and glycerol were added, then formed M-silicates were heated at 800 °C. Then, obtained white solid M-Silicates were characterized by Scanning Electron Microscopy (SEM). SEM images show the variance of surface morphology when the temperature increases. The addition of organic compounds is involved in surface modification.

The utilization of waste by-products for removing silicate from mineral processing wastewater via chemical precipitation.

PubMed

Kang, Jianhua; Sun, Wei; Hu, Yuehua; Gao, Zhiyong; Liu, Runqing; Zhang, Qingpeng; Liu, Hang; Meng, Xiangsong

2017-11-15

This study investigates an environmentally friendly technology that utilizes waste by-products (waste acid and waste alkali liquids) to treat mineral processing wastewater. Chemical precipitation is used to remove silicate from scheelite (CaWO 4 ) cleaning flotation wastewater and the waste by-products are used as a substitute for calcium chloride (CaCl 2 ). A series of laboratory experiments is conducted to explain the removal of silicate and the characterization and formation mechanism of calcium silicate. The results show that silicate removal reaches 90% when the Ca:Si molar ratio exceeds 1.0. The X-ray diffraction (XRD) results confirm the characterization and formation of calcium silicate. The pH is the key factor for silicate removal, and the formation of polysilicic acid with a reduction of pH can effectively improve the silicate removal and reduce the usage of calcium. The economic analysis shows that the treatment costs with waste acid (0.63 $/m 3 ) and waste alkali (1.54 $/m 3 ) are lower than that of calcium chloride (2.38 $/m 3 ). The efficient removal of silicate is confirmed by industrial testing at a plant. The results show that silicate removal reaches 85% in the recycled water from tailings dam. Copyright © 2017 Elsevier Ltd. All rights reserved.

Concept Mapping as a Reading Strategy: Does It Scaffold Comprehension and Recall?

ERIC Educational Resources Information Center

Tajeddin, Zia; Tabatabaei, Soudabeh

2016-01-01

Concept maps reflect the linkage of concepts or facts within a text. This study was set out to investigate whether concept mapping as a learning strategy would have any scaffolding effect on the reading comprehension and recall of propositions by L2 learners. Out of 60 high school students, 30 in the experimental group were exposed to concept…

Argillization by descending acid at Steamboat Springs, Nevada

USGS Publications Warehouse

Schoen, Robert; White, Donald E.; Hemley, J.J.

1974-01-01

Steamboat Springs, Nevada, an area of present-day hot springs, clearly illustrates the genetic dependence of some kaolin deposits on hot-spring activity. Andesite, granodiorite and arkosic sediments are locally altered at the land surface to siliceous residues consisting of primary quartz and anatase, plus opal from primary silicates. These siliceous residues commonly exhibit the textural and structural features of their unaltered equivalents. Beneath the siliceous residues, kaolin and alunite replace primary silicates and fill open spaces, forming a blanketlike deposit. Beneath the kaolin-alunite zone, montmorillonite, commonly accompanied by pyrite, replaces the primary silicates. On the ground surface, the same alteration mineral zones can be traced outward from the siliceous residue; however, hematite rather than pyrite accompanies montmorillonite.Chemical analysis indicates that sulfuric acid is the active altering agent. The acid forms from hydrogen sulfide that exsolves from deep thermal water, rises above the water table and is oxidized by sulfur-oxidizing bacteria living near the ground surface. This acid dissolves in precipitation or condensed water vapor and percolates downward destroying most of the primary minerals producing a siliceous residue. Coincidence of the water table with the downward transition from siliceous residue to kaolin-alunite signifies decreasing hydrogen metasomatism because of dilution of descending acid by ground water.In hot-spring areas, beds of siliceous sinter deposited at the surface by hypogene thermal water look, superficially, like areas of surficial acid alteration. Features diagnostic of a surficial alteration are the relict rock structures of a siliceous residue and a kaolin-alunite zone immediately beneath.

Influence of Silicate Melt Composition on Metal/Silicate Partitioning of W, Ge, Ga and Ni

NASA Technical Reports Server (NTRS)

Singletary, S. J.; Domanik, K.; Drake, M. J.

2005-01-01

The depletion of the siderophile elements in the Earth's upper mantle relative to the chondritic meteorites is a geochemical imprint of core segregation. Therefore, metal/silicate partition coefficients (Dm/s) for siderophile elements are essential to investigations of core formation when used in conjunction with the pattern of elemental abundances in the Earth's mantle. The partitioning of siderophile elements is controlled by temperature, pressure, oxygen fugacity, and by the compositions of the metal and silicate phases. Several recent studies have shown the importance of silicate melt composition on the partitioning of siderophile elements between silicate and metallic liquids. It has been demonstrated that many elements display increased solubility in less polymerized (mafic) melts. However, the importance of silicate melt composition was believed to be minor compared to the influence of oxygen fugacity until studies showed that melt composition is an important factor at high pressures and temperatures. It was found that melt composition is also important for partitioning of high valency siderophile elements. Atmospheric experiments were conducted, varying only silicate melt composition, to assess the importance of silicate melt composition for the partitioning of W, Co and Ga and found that the valence of the dissolving species plays an important role in determining the effect of composition on solubility. In this study, we extend the data set to higher pressures and investigate the role of silicate melt composition on the partitioning of the siderophile elements W, Ge, Ga and Ni between metallic and silicate liquid.

Tableting properties of silica aerogel and other silicates.

PubMed

Hentzschel, C M; Alnaief, M; Smirnova, I; Sakmann, A; Leopold, C S

2012-04-01

In solid oral dosage forms silicates are commonly used as glidants in low concentration. However, due to their large specific surface area, silicates may also be used as carrier materials for drugs. Moreover, silicates allow amorphisation of drugs by co-grinding or processing with supercritical fluids. The aim of this study was to investigate the physical and the tableting properties of Silica Aerogel (special type of silica with an extremely large specific surface area), Neusilin(®) US2 (magnesium aluminometasilicate), Florite(®) (calcium silicate) and Aerosil(®) 200 (colloidal silica). Powder blends of Avicel(®) PH102 (microcrystalline cellulose) and different amounts of the respective silicate were compacted and analyzed for their tabletability (tensile strength vs. compaction pressure) as well as their Heckel plot. With Neusilin(®) the tabletability appeared to be independent of the silicate concentration, whereas with Florite(®) an increasing silicate concentration led to a higher tensile strength. In contrast, the addition of Silica Aerogel and Aerosil(®) resulted in a decrease of the tensile strength. With Aerosil(®) a maximum tolerable concentration of 20% [w/w] was determined. Plastic deformation of all powder blends decreased with increasing silicate concentration. This effect was most pronounced with Aerosil(®) and least with Florite(®). Tablets with acceptable tensile strength were obtained with all plain silicates except for Aerosil(®). Therefore, these silicates may be used in tablet formulations, e.g. as carrier materials for liquid or amorphous drugs.

Identification of the Hydrogeochemical Processes in Groundwater Using Classic Integrated Geochemical Methods and Geostatistical Techniques, in Amol-Babol Plain, Iran

PubMed Central

Sheikhy Narany, Tahoora; Ramli, Mohammad Firuz; Aris, Ahmad Zaharin; Sulaiman, Wan Nor Azmin; Juahir, Hafizan; Fakharian, Kazem

2014-01-01

Hydrogeochemical investigations had been carried out at the Amol-Babol Plain in the north of Iran. Geochemical processes and factors controlling the groundwater chemistry are identified based on the combination of classic geochemical methods with geographic information system (GIS) and geostatistical techniques. The results of the ionic ratios and Gibbs plots show that water rock interaction mechanisms, followed by cation exchange, and dissolution of carbonate and silicate minerals have influenced the groundwater chemistry in the study area. The hydrogeochemical characteristics of groundwater show a shift from low mineralized Ca-HCO3, Ca-Na-HCO3, and Ca-Cl water types to high mineralized Na-Cl water type. Three classes, namely, C1, C2, and C3, have been classified using cluster analysis. The spatial distribution maps of Na+/Cl−, Mg2+/Ca2+, and Cl−/HCO3 − ratios and electrical conductivity values indicate that the carbonate and weathering of silicate minerals played a significant role in the groundwater chemistry on the southern and western sides of the plain. However, salinization process had increased due to the influence of the evaporation-precipitation process towards the north-eastern side of the study area. PMID:24523640

Microscopic processes ruling the bioavailability of Zn to roots of Euphorbia pithyusa L. pioneer plant.

PubMed

Medas, Daniela; De Giudici, Giovanni; Casu, Maria Antonietta; Musu, Elodia; Gianoncelli, Alessandra; Iadecola, Antonella; Meneghini, Carlo; Tamburini, Elena; Sprocati, Anna Rosa; Turnau, Katarzyna; Lattanzi, Pierfranco

2015-02-03

Euphorbia pithyusa L. was used in a plant growth-promoting assisted field trial experiment. To unravel the microscopic processes at the interface, thin slices of E. pithyusa roots were investigated by micro-X-ray fluorescence mapping. Roots and rhizosphere materials were examined by X-ray absorption spectroscopy at the Zn K-edge, X-ray diffraction, and scanning electron microscopy. Results indicate some features common to all the investigated samples. (i) In the rhizosphere of E. pithyusa, Zn was found to exist in different phases. (ii) Si and Al are mainly concentrated in a rim at the epidermis of the roots. (iii) Zn is mostly stored in root epidermis and does not appear to be coordinated to organic molecules but mainly occurs in mineral phases such as Zn silicates. We interpreted that roots of E. pithyusa significantly promote mineral evolution in the rhizosphere. Concomitantly, the plant uses Si and Al extracted by soil minerals to build a biomineralization rim, which can capture Zn. This Zn silicate biomineralization has relevant implications for phytoremediation techniques and for further biotechnology development, which can be better designed and developed after specific knowledge of molecular processes ruling mineral evolution and biomineralization processes has been gained.

Regularities in Low-Temperature Phosphatization of Silicates

NASA Astrophysics Data System (ADS)

Savenko, A. V.

2018-01-01

The regularities in low-temperature phosphatization of silicates are defined from long-term experiments on the interaction between different silicate minerals and phosphate-bearing solutions in a wide range of medium acidity. It is shown that the parameters of the reaction of phosphatization of hornblende, orthoclase, and labradorite have the same values as for clayey minerals (kaolinite and montmorillonite). This effect may appear, if phosphotization proceeds, not after silicate minerals with a different structure and composition, but after a secondary silicate phase formed upon interaction between silicates and water and stable in a certain pH range. Variation in the parameters of the reaction of phosphatization at pH ≈ 1.8 is due to the stability of the silicate phase different from that at higher pH values.

Geologic map of the Skull Creek Quadrangle, Moffat County Colorado

USGS Publications Warehouse

Van Loenen, R. E.; Selner, Gary; Bryant, W.A.

1999-01-01

The Skull Creek quadrangle is in northwestern Colorado a few miles north of Rangely. The prominent structural feature of the Skull Creek quadrangle is the Skull Creek monocline. Pennsylvanian rocks are exposed along the axis of the monocline while hogbacks along its southern flank expose rocks that are from Permian to Upper Cretaceous in age. The Wolf Creek monocline and the Wolf Creek thrust fault, which dissects the monocline, are salient structural features in the northern part of the quadrangle. Little or no mineral potential exists within the quadrangle. A geologic map of the Lazy Y Point quadrangle, which is adjacent to the Skull Creek quadrangle on the west, is also available (Geologic Investigations Series I-2646). This companian map shows similar geologic features, including the western half of the Skull Creek monocline. The geology of this quadrangle was mapped because of its proximity to Dinosaur National Monument. It is adjacent to quadrangles previously mapped to display the geology of this very scenic and popular National Monument. The Skull Creek quadrangle includes parts of the Skull Creek Wilderness Study Area, which was assessed for its mineral resource potential.

EXTINCTION AND POLYCYCLIC AROMATIC HYDROCARBON INTENSITY VARIATIONS ACROSS THE H II REGION IRAS 12063-6259

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stock, D. J.; Peeters, E.; Otaguro, J. N.

The spatial variations in polycyclic aromatic hydrocarbon (PAH) band intensities are normally attributed to the physical conditions of the emitting PAHs, however in recent years it has been suggested that such variations are caused mainly by extinction. To resolve this question, we have obtained near-infrared (NIR), mid-infrared (MIR), and radio observations of the compact H II region IRAS 12063-6259. We use these data to construct multiple independent extinction maps and also to measure the main PAH features (6.2, 7.7, 8.6, and 11.2 {mu}m) in the MIR. Three extinction maps are derived: the first using the NIR hydrogen lines and casemore » B recombination theory; the second combining the NIR data with radio data; and the third making use of the Spitzer/IRS MIR observations to measure the 9.8 {mu}m silicate absorption feature using the Spoon method and PAHFIT (as the depth of this feature can be related to overall extinction). The silicate absorption over the bright, southern component of IRAS 12063-6259 is almost absent while the other methods find significant extinction. While such breakdowns of the relationship between the NIR extinction and the 9.8 {mu}m absorption have been observed in molecular clouds, they have never been observed for H II regions. We then compare the PAH intensity variations in the Spitzer/IRS data after dereddening to those found in the original data. It was found that in most cases, the PAH band intensity variations persist even after dereddening, implying that extinction is not the main cause of the PAH band intensity variations.« less

21 CFR 582.2437 - Magnesium silicate.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Magnesium silicate. 582.2437 Section 582.2437 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Magnesium silicate. (a) Product. Magnesium silicate. (b) Tolerance. 2 percent. (c) Limitations, restrictions...

21 CFR 582.2437 - Magnesium silicate.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Magnesium silicate. 582.2437 Section 582.2437 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Magnesium silicate. (a) Product. Magnesium silicate. (b) Tolerance. 2 percent. (c) Limitations, restrictions...

21 CFR 582.2437 - Magnesium silicate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Magnesium silicate. 582.2437 Section 582.2437 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Magnesium silicate. (a) Product. Magnesium silicate. (b) Tolerance. 2 percent. (c) Limitations, restrictions...

21 CFR 582.2437 - Magnesium silicate.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Magnesium silicate. 582.2437 Section 582.2437 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Magnesium silicate. (a) Product. Magnesium silicate. (b) Tolerance. 2 percent. (c) Limitations, restrictions...

21 CFR 582.2437 - Magnesium silicate.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Magnesium silicate. 582.2437 Section 582.2437 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Magnesium silicate. (a) Product. Magnesium silicate. (b) Tolerance. 2 percent. (c) Limitations, restrictions...

Influence of the type of aqueous sodium silicate on the stabilization and rheology of kaolin clay suspensions

NASA Astrophysics Data System (ADS)

Izak, Piotr; Ogłaza, Longin; Mozgawa, Włodzimierz; Mastalska-Popławska, Joanna; Stempkowska, Agata

2018-05-01

To avoid agglomeration and sedimentation of grains, ceramic slurries should be modified by stabilizers in order to increase the electrostatic interactions between the dispersed particles. In this study we present the spectral analysis of aqueous sodium silicates obtained by different synthesis methods and their influence on the rheological properties of kaolin based slurries. Infrared and Raman spectra can be used to describe the structure of silicate structural units present in aqueous sodium silicates. It was confirmed that the best stabilization results possess aqueous sodium silicates of the silicate moduli of about 2 and the optimal concentration of the used fluidizer is 0.3 wt% to the kaolin clay dry mass. One of the most important conclusions is that the synthesis method of the fluidizer has no significant effect on its stabilization properties but used medium does create adequate stabilization mechanism depending on the silicate structures present in the sodium silicate solution.

SILICATE COMPOSITION OF THE INTERSTELLAR MEDIUM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fogerty, S.; Forrest, W.; Watson, D. M.

2016-10-20

The composition of silicate dust in the diffuse interstellar medium and in protoplanetary disks around young stars informs our understanding of the processing and evolution of the dust grains leading up to planet formation. An analysis of the well-known 9.7 μ m feature indicates that small amorphous silicate grains represent a significant fraction of interstellar dust and are also major components of protoplanetary disks. However, this feature is typically modeled assuming amorphous silicate dust of olivine and pyroxene stoichiometries. Here, we analyze interstellar dust with models of silicate dust that include non-stoichiometric amorphous silicate grains. Modeling the optical depth alongmore » lines of sight toward the extinguished objects Cyg OB2 No. 12 and ζ Ophiuchi, we find evidence for interstellar amorphous silicate dust with stoichiometry intermediate between olivine and pyroxene, which we simply refer to as “polivene.” Finally, we compare these results to models of silicate emission from the Trapezium and protoplanetary disks in Taurus.« less

The role of MAP kinases in the induction of iNOS expression in neutrophils exposed to NDMA: the involvement transcription factors.

PubMed

Ratajczak-Wrona, W; Jablonska, E; Garley, M; Jablonski, J; Radziwon, P; Iwaniuk, A

2013-01-01

The role of MAP kinases in the activation of AP-1 (c-Jun, c-Fos) and NF-κB p65 engaged in the regulation of iNOS expression in human neutrophils (PMNs) exposed to N-nitrosodimethylamine (NDMA) was analyzed in the study. The study included a group of 20 healthy individuals. Isolated human PMN were incubated in the presence of NDMA. Selective MAP kinases inhibitors were used. The expression of proteins in the cytoplasmic and nuclear fractions was assessed using Western blot method. The results show that NDMA intensifies iNOS, c-Jun, NF-κB p65 and IκB-α expression in the analyzed PMNs. The blocking of the p38 pathway led to lower iNOS expression, and higher expression of c-Jun and c-Fos in the cytoplasmic fraction, and also lower c-Jun expression in the nuclear fraction of PMNs exposed to NDMA. A decrease in iNOS expression in the cytoplasmic fraction, and also c-Jun in both fractions of the examined cells, was observed as a result of JNK pathway inhibition. The blocking of the ERK5 pathway led to higher iNOS, c-Jun and c-Fos expression in the cytoplasmic fraction, and higher c-Jun expression in the nuclear fraction of PMNs exposed to NDMA. The study also demonstrated that blocking of the p38 and JNK pathways resulted in higher expression of NF-κB p65 and IκB-α in the cytoplasmic fraction and their lower expression in the nuclear fraction of these cells. Our data indicate the role of MAP kinases p38 and JNK in the activation of c-Jun and NF-κB p65 transcription factors engaged in the regulation of iNOS expression in human neutrophils exposed to NDMA. However ERK5 kinase is not involved in the regulation of iNOS and NO production by those cells.

Evaluation of an urban traffic Noise-Exposed population based on points of interest and noise maps: The case of Guangzhou.

PubMed

Wang, Haibo; Chen, Hanjie; Cai, Ming

2018-08-01

The primary objective of this study was to develop an evaluation method for assessing an urban traffic noise-exposed population and apply it in the main urban area of Guangzhou. The method based on points of interest (POIs) and noise map is realized in several steps. First, after regionalizing based on road networks and executing a cluster analysis for regions according to the properties of POIs, the environmental noise functional regions (NFRs) of the urban area are presented. Then, surrounding POIs are used to infer the type of buildings, and according to the attraction of different building types and the whole population of the region, the population distribution at the building level is calculated. Finally, with the help of a noise map, an evaluation method for assessing an urban traffic noise-exposed population is proposed. The method is applied in the main urban area of Guangzhou, and the results reveal the followings. 1) At daytime and nighttime, 23.63% and 30.53% of the population, respectively, experience noise levels that exceed the noise standards. The per capita noise exposure value at daytime and nighttime is 0.9 dB and 2.0 dB, respectively. 2) The percentages of the exposed population of Yuexiu District were 28.89% at daytime and 35.65% at nighttime, which are the largest, followed by the exposed population percentages of Liwan, Haizhu, and Tianhe Districts. 3) From the view of different classes of NFRs, the percentages of the exposed population of Class 1 and Class 4 are larger than the percentages of the exposed population from the other classes, especially at nighttime (48.24% of Class 1 and 40.79% of Class 4). 4) Although there are masses of people affected by traffic noise, a large percentage of them (85%) experience not more than 5 dB of traffic noise superscale. Copyright © 2018 Elsevier Ltd. All rights reserved.

Can early host responses to mycobacterial infection predict eventual disease outcomes?

PubMed

de Silva, Kumudika; Begg, Douglas J; Plain, Karren M; Purdie, Auriol C; Kawaji, Satoko; Dhand, Navneet K; Whittington, Richard J

2013-11-01

Diagnostic tests used for Johne's disease in sheep either have poor sensitivity and specificity or only detect disease in later stages of infection. Predicting which of the infected sheep are likely to become infectious later in life is currently not feasible and continues to be a major hindrance in disease control. We conducted this longitudinal study to investigate if a suite of diagnostic tests conducted in Mycobacterium avium subspecies paratuberculosis (MAP) exposed lambs at 4 months post infection can accurately predict their clinical status at 12 months post infection. We tracked cellular and humoral responses and quantity of MAP shedding for up to 12 months post challenge in 20 controls and 37 exposed sheep. Infection was defined at necropsy by tissue culture and disease spectrum by lesion type. Data were analysed using univariable and multivariable logistic regression models and a subset of variables from the earliest period post inoculation (4 months) was selected for predicting disease outcomes later on (12 months). Sensitivity and specificity of tests and their combinations in series and parallel were determined. Early elevation in faecal MAP DNA quantity and a lower interferon gamma (IFNγ) response were significantly associated with sheep becoming infectious as well as progressing to severe disease. Conversely, early low faecal MAP DNA and higher interleukin-10 responses were significantly associated with an exposed animal developing protective immunity. Combination of early elevated faecal MAP DNA or lower IFNγ response had the highest sensitivity (75%) and specificity (81%) for identifying sheep that would become infectious. Collectively, these results highlight the potential for combined test interpretation to aid in the early prediction of sheep susceptibility to MAP infection. Copyright © 2013 Elsevier B.V. All rights reserved.

40 CFR 721.9513 - Modified magnesium silicate polymer (generic).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Modified magnesium silicate polymer... Specific Chemical Substances § 721.9513 Modified magnesium silicate polymer (generic). (a) Chemical... as modified magnesium silicate polymer (PMN P-98-604) is subject to reporting under this section for...

40 CFR 721.9513 - Modified magnesium silicate polymer (generic).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Modified magnesium silicate polymer... Specific Chemical Substances § 721.9513 Modified magnesium silicate polymer (generic). (a) Chemical... as modified magnesium silicate polymer (PMN P-98-604) is subject to reporting under this section for...

21 CFR 182.2437 - Magnesium silicate.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Magnesium silicate. 182.2437 Section 182.2437 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Magnesium silicate. (a) Product. Magnesium silicate. (b) Tolerance. 2 percent. (c) Limitations, restrictions...

21 CFR 182.2437 - Magnesium silicate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Magnesium silicate. 182.2437 Section 182.2437 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Magnesium silicate. (a) Product. Magnesium silicate. (b) Tolerance. 2 percent. (c) Limitations, restrictions...

21 CFR 182.2437 - Magnesium silicate.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Magnesium silicate. 182.2437 Section 182.2437 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Magnesium silicate. (a) Product. Magnesium silicate. (b) Tolerance. 2 percent. (c) Limitations, restrictions...

21 CFR 182.2437 - Magnesium silicate.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Magnesium silicate. 182.2437 Section 182.2437 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Magnesium silicate. (a) Product. Magnesium silicate. (b) Tolerance. 2 percent. (c) Limitations, restrictions...

21 CFR 182.2122 - Aluminum calcium silicate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Aluminum calcium silicate. 182.2122 Section 182.2122 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED....2122 Aluminum calcium silicate. (a) Product. Aluminum calcium silicate. (b) Tolerance. 2 percent. (c...

21 CFR 182.2122 - Aluminum calcium silicate.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Aluminum calcium silicate. 182.2122 Section 182.2122 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED....2122 Aluminum calcium silicate. (a) Product. Aluminum calcium silicate. (b) Tolerance. 2 percent. (c...

21 CFR 582.2122 - Aluminum calcium silicate.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Aluminum calcium silicate. 582.2122 Section 582.2122 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED....2122 Aluminum calcium silicate. (a) Product. Aluminum calcium silicate. (b) Tolerance. 2 percent. (c...

21 CFR 582.2122 - Aluminum calcium silicate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Aluminum calcium silicate. 582.2122 Section 582.2122 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED....2122 Aluminum calcium silicate. (a) Product. Aluminum calcium silicate. (b) Tolerance. 2 percent. (c...

21 CFR 582.2227 - Calcium silicate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Calcium silicate. 582.2227 Section 582.2227 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Calcium silicate. (a) Product. Calcium silicate. (b) Tolerance. 2 percent and 5 percent. (c) Limitations...

21 CFR 582.2227 - Calcium silicate.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Calcium silicate. 582.2227 Section 582.2227 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Calcium silicate. (a) Product. Calcium silicate. (b) Tolerance. 2 percent and 5 percent. (c) Limitations...

40 CFR 721.9513 - Modified magnesium silicate polymer (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Modified magnesium silicate polymer... Specific Chemical Substances § 721.9513 Modified magnesium silicate polymer (generic). (a) Chemical... as modified magnesium silicate polymer (PMN P-98-604) is subject to reporting under this section for...

40 CFR 721.9513 - Modified magnesium silicate polymer (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Modified magnesium silicate polymer... Specific Chemical Substances § 721.9513 Modified magnesium silicate polymer (generic). (a) Chemical... as modified magnesium silicate polymer (PMN P-98-604) is subject to reporting under this section for...

40 CFR 721.9513 - Modified magnesium silicate polymer (generic).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Modified magnesium silicate polymer... Specific Chemical Substances § 721.9513 Modified magnesium silicate polymer (generic). (a) Chemical... as modified magnesium silicate polymer (PMN P-98-604) is subject to reporting under this section for...

21 CFR 582.2122 - Aluminum calcium silicate.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Aluminum calcium silicate. 582.2122 Section 582.2122 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED....2122 Aluminum calcium silicate. (a) Product. Aluminum calcium silicate. (b) Tolerance. 2 percent. (c...

21 CFR 582.2227 - Calcium silicate.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Calcium silicate. 582.2227 Section 582.2227 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Calcium silicate. (a) Product. Calcium silicate. (b) Tolerance. 2 percent and 5 percent. (c) Limitations...

21 CFR 182.2122 - Aluminum calcium silicate.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Aluminum calcium silicate. 182.2122 Section 182.2122 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED....2122 Aluminum calcium silicate. (a) Product. Aluminum calcium silicate. (b) Tolerance. 2 percent. (c...

21 CFR 582.2122 - Aluminum calcium silicate.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Aluminum calcium silicate. 582.2122 Section 582.2122 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED....2122 Aluminum calcium silicate. (a) Product. Aluminum calcium silicate. (b) Tolerance. 2 percent. (c...

21 CFR 582.2227 - Calcium silicate.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Calcium silicate. 582.2227 Section 582.2227 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Calcium silicate. (a) Product. Calcium silicate. (b) Tolerance. 2 percent and 5 percent. (c) Limitations...

21 CFR 582.2122 - Aluminum calcium silicate.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Aluminum calcium silicate. 582.2122 Section 582.2122 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED....2122 Aluminum calcium silicate. (a) Product. Aluminum calcium silicate. (b) Tolerance. 2 percent. (c...

21 CFR 182.2227 - Calcium silicate.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Calcium silicate. 182.2227 Section 182.2227 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Anticaking Agents § 182.2227 Calcium silicate. (a) Product. Calcium silicate...

21 CFR 582.2227 - Calcium silicate.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Calcium silicate. 582.2227 Section 582.2227 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Calcium silicate. (a) Product. Calcium silicate. (b) Tolerance. 2 percent and 5 percent. (c) Limitations...

21 CFR 182.2122 - Aluminum calcium silicate.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Aluminum calcium silicate. 182.2122 Section 182...) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Anticaking Agents § 182.2122 Aluminum calcium silicate. (a) Product. Aluminum calcium silicate. (b) Tolerance. 2 percent. (c) Limitations, restrictions, or explanation. This...

21 CFR 182.2122 - Aluminum calcium silicate.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Aluminum calcium silicate. 182.2122 Section 182.2122 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED....2122 Aluminum calcium silicate. (a) Product. Aluminum calcium silicate. (b) Tolerance. 2 percent. (c...

Corrosion resistant thermal barrier coating. [protecting gas turbines and other engine parts

NASA Technical Reports Server (NTRS)

Levine, S. R.; Miller, R. A.; Hodge, P. E. (Inventor)

1981-01-01

A thermal barrier coating system for protecting metal surfaces at high temperature in normally corrosive environments is described. The thermal barrier coating system includes a metal alloy bond coating, the alloy containing nickel, cobalt, iron, or a combination of these metals. The system further includes a corrosion resistant thermal barrier oxide coating containing at least one alkaline earth silicate. The preferred oxides are calcium silicate, barium silicate, magnesium silicate, or combinations of these silicates.

Constraining the Dust Opacity Law in Three Small and Isolated Molecular Clouds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Webb, K. A.; Thanjavur, K.; Di Francesco, J.

Density profiles of isolated cores derived from thermal dust continuum emission rely on models of dust properties, such as mass opacity, that are poorly constrained. With complementary measures from near-infrared extinction maps, we can assess the reliability of commonly used dust models. In this work, we compare Herschel -derived maps of the optical depth with equivalent maps derived from CFHT WIRCAM near-infrared observations for three isolated cores: CB 68, L 429, and L 1552. We assess the dust opacities provided from four models: OH1a, OH5a, Orm1, and Orm4. Although the consistency of the models differs between the three sources, themore » results suggest that the optical properties of dust in the envelopes of the cores are best described by either silicate and bare graphite grains (e.g., Orm1) or carbonaceous grains with some coagulation and either thin or no ice mantles (e.g., OH5a). None of the models, however, individually produced the most consistent optical depth maps for every source. The results suggest that either the dust in the cores is not well-described by any one dust property model, the application of the dust models cannot be extended beyond the very center of the cores, or more complex SED fitting functions are necessary.« less

Development and validation of a triplex real-time PCR for rapid detection and specific identification of M. avium sub sp. paratuberculosis in faecal samples.

PubMed

Irenge, Léonid M; Walravens, Karl; Govaerts, Marc; Godfroid, Jacques; Rosseels, Valérie; Huygen, Kris; Gala, Jean-Luc

2009-04-14

A triplex real-time (TRT-PCR) assay was developed to ensure a rapid and reliable detection of Mycobacterium avium subsp. paratuberculosis (Map) in faecal samples and to allow routine detection of Map in farmed livestock and wildlife species. The TRT-PCR assay was designed using IS900, ISMAP02 and f57 molecular targets. Specificity of TRT-PCR was first confirmed on a panel of control mycobacterial Map and non-Map strains and on faecal samples from Map-negative cows (n=35) and from Map-positive cows (n=20). The TRT-PCR assay was compared to direct examination after Ziehl-Neelsen (ZN) staining and to culture on 197 faecal samples collected serially from five calves experimentally exposed to Map over a 3-year period during the sub-clinical phase of the disease. The data showed a good agreement between culture and TRT-PCR (kappa score=0.63), with the TRT-PCR limit of detection of 2.5 x 10(2)microorganisms/g of faeces spiked with Map. ZN agreement with TRT-PCR was not good (kappa=0.02). Sequence analysis of IS900 amplicons from three single IS900 positive samples confirmed the true Map positivity of the samples. Highly specific IS900 amplification suggests therefore that each single IS900 positive sample from experimentally exposed animals was a true Map-positive specimen. In this controlled experimental setting, the TRT-PCT was rapid, specific and displayed a very high sensitivity for Map detection in faecal samples compared to conventional methods.

Measurement of the decay rate of the SiH feature as a function of temperature

NASA Technical Reports Server (NTRS)

Nuth, Joseph A., III; Kraus, George F.

1994-01-01

We have previously suggested that the SiH fundamental stretch could serve as a diagnostic indicator of the oxidation state of silicate surfaces exposed to the solar wind for prolonged periods. We have now measured the primary decay rate of SiH in vacuo as a function of temperature and find that the primary rate constant for the decay can be characterized by the following equation: k(min(exp -1)) approximately equals 0.186 exp(-9/RT) min(exp -1), where R = 2 x 10(exp -3) kcal deg(exp -1) mole(exp -1). This means that the half-life for the decay of the SiH feature at room temperature is approximately 20 yrs, whereas the half-life at a peak lunar regolith temperature of approximately 500K would be only approximately 20 days. At the somewhat lower temperature of approximately 400K the half-life for the decay is on the order of 200 days. The rate of loss of SiH as a function of temperature provides an upper limit to the quantity of H implanted by the solar wind which can be retained by a silicate grain in a planetary regolith. This will be discussed in more detail here.

Metal-silicate interaction in quenched shock-induced melt of the Tenham L6-chondrite

NASA Astrophysics Data System (ADS)

Leroux, Hugues; Doukhan, Jean-Claude; Guyot, François

2000-07-01

The metal-silicate microstructures in the shock-induced melt pockets of the Tenham (L6) chondrite have been investigated by analytical transmission electron microscopy. The melt areas, formed under high-pressure, high-temperature dynamic shock conditions, consist of spherical Fe-Ni metal/iron sulfide globules embedded in a silicate glass matrix, showing that the melt was quenched at high cooling rate. The Fe-Ni fraction in the globules is two-phase, composed of a bcc phase (˜5 wt% Ni) and an fcc phase (˜49 wt% Ni), indicating that fractional crystallisation of the metal occurred during the fast cooling. The metal fraction also contains appreciable amounts of non-siderophile elements (mostly Si, Mg and O) suggesting that these elements were trapped in the metal, either as alloying components or as tiny silicate or oxide inclusions. In the iron sulfide fraction, the Na content is high (>3 wt%), suggesting chalcophile behaviour for Na during the shock event. The composition of the silicate glass reflects non-equilibrium melting of several silicate phases (olivine, pyroxene and plagioclase). Moreover, the FeO content is high compared to the FeO contents of the unmelted silicates. Some Fe redistribution took place between metal and silicate liquids during the shock event. The silicate glass also contains tiny iron sulfide precipitates which most probably originated by exsolution during quench, suggesting that the molten silicate retained significant amounts of S, dissolved at high temperature and high pressure. Based on these observations, we suggest that non-equilibrium phenomena may be important in determining the compositions of metal and silicate reservoirs during their differentiation.

Experimental segregation of iron-nickel metal, iron-sulfide, and olivine in a thermal gradient: Preliminary results

NASA Technical Reports Server (NTRS)

Jurewicz, Stephen R.; Jones, J. H.

1993-01-01

Speculation about the possible mechanisms for core formation in small asteroids raises more questions than answers. Petrologic evidence from iron meteorites, pallasites, and astronomical observations of M asteroids suggests that many small bodies were capable of core formation. Recent work by Taylor reviews the geochemical evidence and examines the possible physical/mechanical constraints on segregation processes. Taylor's evaluation suggests that extensive silicate partial melting (preferably 50 vol. percent or greater) is required before metal can segregate from the surrounding silicate and form a metal core. The arguments for large degrees of silicate partial melting are two-fold: (1) elemental trends in iron meteorites require that the metal was at is liquidus; and (2) experimental observations of metal/sulfide inclusions in partially molten silicate meteorites show that the metal/sulfide tends to form spherules in the liquid silicate due to surface tension effects. Taylor points out that for these metal spherules to sink through a silicate mush, high degrees of silicate partial melting are required to lower the silicate yield strength. Although some qualitative experimental data exists, little is actually known about the behavior of metals and liquid sulfides dispersed in silicate systems. In addition, we have been impressed with the ability of cumulative olivine to expel trapped liquid when placed in a thermal gradient. Consequently, we undertook to accomplish the following: (1) experimentally evaluate the potential for metal/sulfide/silicate segregation in a thermal gradient; and (2) obtain quantitative data of the wetting parameters of metal-sulfide melts among silicate grains.

Pancam multispectral imaging results from the Spirit Rover at Gusev crater

USGS Publications Warehouse

Bell, J.F.; Squyres, S. W.; Arvidson, R. E.; Arneson, H.M.; Bass, D.; Blaney, D.; Cabrol, N.; Calvin, W.; Farmer, J.; Farrand, W. H.; Goetz, W.; Golombek, M.; Grant, J. A.; Greeley, R.; Guinness, E.; Hayes, A.G.; Hubbard, M.Y.H.; Herkenhoff, K. E.; Johnson, M.J.; Johnson, J. R.; Joseph, J.; Kinch, K.M.; Lemmon, M.T.; Li, R.; Madsen, M.B.; Maki, J.N.; Malin, M.; McCartney, E.; McLennan, S.; McSween, H.Y.; Ming, D. W.; Moersch, J.E.; Morris, R.V.; Dobrea, E.Z.N.; Parker, T.J.; Proton, J.; Rice, J. W.; Seelos, F.; Soderblom, J.; Soderblom, L.A.; Sohl-Dickstein, J. N.; Sullivan, R.J.; Wolff, M.J.; Wang, A.

2004-01-01

Panoramic Camera images at Gusev crater reveal a rock-strewn surface interspersed with high- to moderate-albedo fine-grained deposits occurring in part as drifts or in small circular swales or hollows. Optically thick coatings of fine-grained ferric iron-rich dust dominate most bright soil and rock surfaces. Spectra of some darker rock surfaces and rock regions exposed by brushing or grinding show near-infrared spectral signatures consistent with the presence of mafic silicates such as pyroxene or olivine. Atmospheric observations show a steady decline in dust opacity during the mission, and astronomical observations captured solar transits by the martian moons, Phobos and Deimos, as well as a view of Earth from the martian surface.

Pancam multispectral imaging results from the Spirit Rover at Gusev Crater.

PubMed

Bell, J F; Squyres, S W; Arvidson, R E; Arneson, H M; Bass, D; Blaney, D; Cabrol, N; Calvin, W; Farmer, J; Farrand, W H; Goetz, W; Golombek, M; Grant, J A; Greeley, R; Guinness, E; Hayes, A G; Hubbard, M Y H; Herkenhoff, K E; Johnson, M J; Johnson, J R; Joseph, J; Kinch, K M; Lemmon, M T; Li, R; Madsen, M B; Maki, J N; Malin, M; McCartney, E; McLennan, S; McSween, H Y; Ming, D W; Moersch, J E; Morris, R V; Dobrea, E Z Noe; Parker, T J; Proton, J; Rice, J W; Seelos, F; Soderblom, J; Soderblom, L A; Sohl-Dickstein, J N; Sullivan, R J; Wolff, M J; Wang, A

2004-08-06

Panoramic Camera images at Gusev crater reveal a rock-strewn surface interspersed with high- to moderate-albedo fine-grained deposits occurring in part as drifts or in small circular swales or hollows. Optically thick coatings of fine-grained ferric iron-rich dust dominate most bright soil and rock surfaces. Spectra of some darker rock surfaces and rock regions exposed by brushing or grinding show near-infrared spectral signatures consistent with the presence of mafic silicates such as pyroxene or olivine. Atmospheric observations show a steady decline in dust opacity during the mission, and astronomical observations captured solar transits by the martian moons, Phobos and Deimos, as well as a view of Earth from the martian surface.

Pancam multispectral imaging results from the Spirit Rover at Gusev Crater

NASA Technical Reports Server (NTRS)

Bell, J. F., III; Squyres, S. W.; Arvidson, R. E.; Arneson, H. M.; Bass, D.; Blaney, D.; Cabrol, N.; Calvin, W.; Farmer, J.; Farrand, W. H.;

Petrography and trace element signatures in silicates and Fe-Ti-oxides from the Lanjiahuoshan deposit, Panzhihua layered intrusion, Southwest China

NASA Astrophysics Data System (ADS)

Gao, Wenyuan; Ciobanu, Cristiana L.; Cook, Nigel J.; Huang, Fei; Meng, Lin; Gao, Shang

2017-12-01

Permian mafic-ultramafic layered intrusions in the central part of the Emeishan Large Igneous Province (ELIP), Southwestern China, host Fe-Ti-V-oxide ores that have features which distinguish them from other large layered intrusion-hosted deposits. The origin of these ores is highly debated. Careful petrographic examination, whole rock analysis, electron probe microanalysis, and measurement and mapping of trace element concentrations by laser ablation inductively coupled plasma mass spectrometry in all major and minor minerals (clinopyroxene, plagioclase, olivine, amphibole, titanomagnetite, ilmenite, pleonaste and pyrrhotite) has been undertaken on samples from the Lanjiahuoshan deposit, representing the Middle, Lower and Marginal Zone of the Panzhihua intrusion. Features are documented that impact on interpretation of intrusion petrology and with implications for genesis of the Fe-Ti-V-oxide ores. Firstly, there is evidence, as symplectites between clinopyroxene and plagioclase, for introduction of complex secondary melts. Secondly, reaction between a late hydrothermal fluid and clinopyroxene is recognized, which has led to formation of hydrated minerals (pargasite, phlogopite), as well as a potassium metasomatic event, postdating intrusion solidification, which led to formation of K-feldspar. Lastly, partitioning of trace elements between titanomagnetite and silicates needs to consider scavenging of metals by ilmenite (Mn, Sc, Zr, Nb, Sn, Hf and Ta) and sulfides, as well as the marked partitioning of Co, Ni, Zn, Ga, As and Sb into spinels exsolved from titanomagnetite. The role of these less abundant phases may have been understated in previous studies, highlighting the importance of petrographic examination of complex silicate-oxide-sulfide assemblages, as well as the need for a holistic approach to trace element analysis, acknowledging all minerals within the assemblage.

Potential effects of climate change on the distribution range of the main silicate sinker of the Southern Ocean.

PubMed

Pinkernell, Stefan; Beszteri, Bánk

2014-08-01

Fragilariopsis kerguelensis, a dominant diatom species throughout the Antarctic Circumpolar Current, is coined to be one of the main drivers of the biological silicate pump. Here, we study the distribution of this important species and expected consequences of climate change upon it, using correlative species distribution modeling and publicly available presence-only data. As experience with SDM is scarce for marine phytoplankton, this also serves as a pilot study for this organism group. We used the maximum entropy method to calculate distribution models for the diatom F. kerguelensis based on yearly and monthly environmental data (sea surface temperature, salinity, nitrate and silicate concentrations). Observation data were harvested from GBIF and the Global Diatom Database, and for further analyses also from the Hustedt Diatom Collection (BRM). The models were projected on current yearly and seasonal environmental data to study current distribution and its seasonality. Furthermore, we projected the seasonal model on future environmental data obtained from climate models for the year 2100. Projected on current yearly averaged environmental data, all models showed similar distribution patterns for F. kerguelensis. The monthly model showed seasonality, for example, a shift of the southern distribution boundary toward the north in the winter. Projections on future scenarios resulted in a moderately to negligibly shrinking distribution area and a change in seasonality. We found a substantial bias in the publicly available observation datasets, which could be reduced by additional observation records we obtained from the Hustedt Diatom Collection. Present-day distribution patterns inferred from the models coincided well with background knowledge and previous reports about F. kerguelensis distribution, showing that maximum entropy-based distribution models are suitable to map distribution patterns for oceanic planktonic organisms. Our scenario projections indicate moderate effects of climate change upon the biogeography of F. kerguelensis.

Distribution of disharmonic en echelon folds in siliceous beds of the Miocene Monterey Formation east of San Luis Obispo, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

McLean, H.

1991-02-01

A discontinuous series of tight, locally en echelon, northwest-trending folds in largely siliceous shales of Miocene Monterey Formation were delineated by recent detailed geologic mapping in the Lopez Mountain 7.5-min. quadrangle, San Luis Obispo County, California. Complexly folded strata within the informally named Lopez Mountain syncline represent the northern terminus of the broader and more gently folded Huasna syncline, which is located 25 km to the southeast. Flank dips on many folds in the Lopez Mountain syncline generally range from 60 to 70{degree} and locally are vertical or slightly overturned. Distances between fold axes range from as little as 100more » m to as much as 1 km. Some folds can be traced for only a few hundred meters, whereas others extend for as much as 3 km. Folding of the siliceous upper part of the Monterey appear to be disharmonic with respect to stratigraphically lower calcareous and/or phosphatic shales. Unconformably underlying Mesozoic and Tertiary strata tend to be less deformed than most Monterey strata, with the exception of highly deformed Franciscan assemblage melange and serpentine that from the basement beneath the Lopez Mountain syncline. The Lopez Mountain syncline lies between the Sur-Nacimiento fault zone on the east and the West Huasna fault zone on the west. Although the timing, magnitude, and sense of motion on the fault zones are poorly constrained, much of Monterey Formation deformation in the Lopez Mountain area probably occurred in latest Miocene or early Pliocene time, possibly as a result of differential wrench movement along the two adjacent fault zones.« less

21 CFR 182.2227 - Calcium silicate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium silicate. 182.2227 Section 182.2227 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Calcium silicate. (a) Product. Calcium silicate. (b) Tolerance. 2 percent and 5 percent. (c) Limitations...

21 CFR 182.2227 - Calcium silicate.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Calcium silicate. 182.2227 Section 182.2227 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Calcium silicate. (a) Product. Calcium silicate. (b) Tolerance. 2 percent and 5 percent. (c) Limitations...

40 CFR 721.9514 - Ethyl silicate, reaction products with modified alkoxysilane salt (generic).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Ethyl silicate, reaction products with... Significant New Uses for Specific Chemical Substances § 721.9514 Ethyl silicate, reaction products with.... (1) The chemical substance identified generically as Ethyl silicate, reaction products with modified...

40 CFR 721.9514 - Ethyl silicate, reaction products with modified alkoxysilane salt (generic).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Ethyl silicate, reaction products with... Significant New Uses for Specific Chemical Substances § 721.9514 Ethyl silicate, reaction products with.... (1) The chemical substance identified generically as Ethyl silicate, reaction products with modified...

21 CFR 182.2227 - Calcium silicate.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Calcium silicate. 182.2227 Section 182.2227 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Calcium silicate. (a) Product. Calcium silicate. (b) Tolerance. 2 percent and 5 percent. (c) Limitations...

21 CFR 182.2227 - Calcium silicate.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Calcium silicate. 182.2227 Section 182.2227 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Calcium silicate. (a) Product. Calcium silicate. (b) Tolerance. 2 percent and 5 percent. (c) Limitations...

Genesis of IIICD Iron Meteorites: Evidence From Silicate Inclusions

NASA Astrophysics Data System (ADS)

McCoy, T. J.; Keil, K.; Scott, E. R. D.; Haack, H.

1992-07-01

The IAB and IIICD iron meteorite groups exhibit much larger ranges in siderophile concentrations than other groups and commonly contain silicate inclusions. Extensive studies of metal in both groups and silicates in IAB irons have led to a variety of ideas to explain the genesis of these groups. Wasson et al. (1980) envision each meteorite forming in a separate impact melt pool. Kracher (1982, 1985) suggested that the siderophile trends might result from fractional crystallization of both metal and troilite in a S-saturated magma. A role for oxidation-reduction in these groups has been proposed by Scott and Bild (1974). Similarities in siderophile elemental trends indicate that IIICD metal has a similar origin, although data on silicate inclusions in IIICD irons are scarce (Ramdohr, 1973; Scott and Bild, 1974; Kracher and Kurat, 1977; Prinz et al., 1982; Clayton et al., 1983). We report the first detailed study of silicate inclusions in IIICD iron meteorites in an attempt to elucidate their history. We have studied the only silicate-bearing IIICD irons - Carlton, Dayton, and the recently reported Maltahohe. Silicate-graphite-phosphate inclusions comprise at most a few percent of the bulk meteorite, and silicates comprise <25 vol% of the inclusion. Silicate mineralogy and chemistry vary systematically with increasing M content of the metal. Maltahohe (10.7 wt% Ni) and Carlton (13.0%) contain olivine, pyroxene, and plagioclase, whereas Dayton (17.0%) contains pyroxene, plagioclase, and SiO2. Pyroxene becomes more FeO-rich from Maltahohe (FS(sub)7.8) to Carlton (Fs(sub)9.7) to Dayton (Fs(sub)11.6). Inverse FeO zoning in silicates and lower Fa than Fs indicate reduction in all three meteorites. Plagioclase compositions in IIICD (An(sub)1.1-4.9) are lower than IAB (An(sub)9.2-2l.5) and uncorrelated with Ni content. The abundances of associated phases also vary. Graphite comprises ~25 vol% of Maltahohe silicate inclusions, but only a few percent in Carlton, and is absent in Dayton silicate inclusions. Phosphate mineralogy and modal abundance also vary, with phosphates absent in Maltahohe, chlorapatite comprising 0-70 vol% of inclusions in Carlton, and the unusual phosphates brianite and panethite, along with whitlockite, comprising up to 55 vol% of Dayton's inclusions. The small number of silicate-bearing IIICD irons require that any conclusions must be considered tentative. The precursor silicate assemblage was similar for IAB and IIICD, as suggested by the general similarity between Maltahohe and IAB silicate inclusions. With increasing Ni contents, however, IIICD and IAB silicate inclusions become dramatically different, as indicated by the mineralogical and chemical trends present in IIICD and absent in IAB silicate inclusions. Silicate inclusions in the Ni-rich IAB irons (e.g., San Cristobal, 25 wt% Ni) do not resemble the phosphate-rich, evolved-silicate assemblages observed in Dayton. It is clear that one or more processes were capable of producing changes in metal compositions and silicate inclusion mineralogy, which correlated with one another. None of the observed trends in silicate mineralogy are predicted by the impact-melt model, although impact might have played a role in mixing silicates into the metallic magma. Some trends are consistent with oxidation-reduction, but variations in some siderophiles (e.g., Ir, Cu) cannot be explained easily by this mechanism. We believe that solid silicates must have been mixed with an evolving metallic melt, with the metallic magma dramatically influencing the mineralogy and chemistry of the inclusion, similar to the fractional crystallization model of Kracher (1982,1985). However, many details of this process remain obscure, including the mechanism that concentrated a S-rich melt, the mixing of metal and silicates, and the fractionation of S. References: Clayton et al. (1983) EPSL 65, 229-232. Kracher (1982) GRL 9, 412-415. Kracher (1985) PLPSC 15, C689-C698. Kracher and Kurat (1977) Meteoritics 12, 282-283. Scott and Bild (1974) GCA 38, 1379-1391. Prinz et al. (1982) LPSC XIlI, 632-633. Ramdohr (1973) Elsevier Pub. Co. Wasson et al. (1980) Z. Naturforsch. 35a, 781-795.

Field reconnaissance geologic mapping of the Columbia Hills, Mars, based on Mars Exploration Rover Spirit and MRO HiRISE observations

NASA Astrophysics Data System (ADS)

Crumpler, L. S.; Arvidson, R. E.; Squyres, S. W.; McCoy, T.; Yingst, A.; Ruff, S.; Farrand, W.; McSween, Y.; Powell, M.; Ming, D. W.; Morris, R. V.; Bell, J. F., III; Grant, J.; Greeley, R.; DesMarais, D.; Schmidt, M.; Cabrol, N. A.; Haldemann, A.; Lewis, Kevin W.; Wang, A. E.; Schröder, C.; Blaney, D.; Cohen, B.; Yen, A.; Farmer, J.; Gellert, R.; Guinness, E. A.; Herkenhoff, K. E.; Johnson, J. R.; Klingelhöfer, G.; McEwen, A.; Rice, J. W., Jr.; Rice, M.; deSouza, P.; Hurowitz, J.

2011-07-01

Chemical, mineralogic, and lithologic ground truth was acquired for the first time on Mars in terrain units mapped using orbital Mars Reconnaissance Orbiter's High Resolution Imaging Science Experiment (MRO HiRISE) image data. Examination of several dozen outcrops shows that Mars is geologically complex at meter length scales, the record of its geologic history is well exposed, stratigraphic units may be identified and correlated across significant areas on the ground, and outcrops and geologic relationships between materials may be analyzed with techniques commonly employed in terrestrial field geology. Despite their burial during the course of Martian geologic time by widespread epiclastic materials, mobile fines, and fall deposits, the selective exhumation of deep and well-preserved geologic units has exposed undisturbed outcrops, stratigraphic sections, and structural information much as they are preserved and exposed on Earth. A rich geologic record awaits skilled future field investigators on Mars. The correlation of ground observations and orbital images enables construction of a corresponding geologic reconnaissance map. Most of the outcrops visited are interpreted to be pyroclastic, impactite, and epiclastic deposits overlying an unexposed substrate, probably related to a modified Gusev crater central peak. Fluids have altered chemistry and mineralogy of these protoliths in degrees that vary substantially within the same map unit. Examination of the rocks exposed above and below the major unconformity between the plains lavas and the Columbia Hills directly confirms the general conclusion from remote sensing in previous studies over past years that the early history of Mars was a time of more intense deposition and modification of the surface. Although the availability of fluids and the chemical and mineral activity declined from this early period, significant later volcanism and fluid convection enabled additional, if localized, chemical activity.

Field Reconnaissance Geologic Mapping of the Columbia Hills, Mars: Results from MER Spirit and MRO HiRISE Observations

USGS Publications Warehouse

Crumpler, L.S.; Arvidson, R. E.; Squyres, S. W.; McCoy, T.; Yingst, A.; Ruff, S.; Farrand, W.; McSween, Y.; Powell, M.; Ming, D. W.; Morris, R.V.; Bell, J.F.; Grant, J.; Greeley, R.; DesMarais, D.; Schmidt, M.; Cabrol, N.A.; Haldemann, A.; Lewis, Kevin W.; Wang, A.E.; Schroder, C.; Blaney, D.; Cohen, B.; Yen, A.; Farmer, J.; Gellert, Ralf; Guinness, E.A.; Herkenhoff, K. E.; Johnson, J. R.; Klingelhofer, G.; McEwen, A.; Rice, J. W.; Rice, M.; deSouza, P.; Hurowitz, J.

2011-01-01

Chemical, mineralogic, and lithologic ground truth was acquired for the first time on Mars in terrain units mapped using orbital Mars Reconnaissance Orbiter's High Resolution Imaging Science Experiment (MRO HiRISE) image data. Examination of several dozen outcrops shows that Mars is geologically complex at meter length scales, the record of its geologic history is well exposed, stratigraphic units may be identified and correlated across significant areas on the ground, and outcrops and geologic relationships between materials may be analyzed with techniques commonly employed in terrestrial field geology. Despite their burial during the course of Martian geologic time by widespread epiclastic materials, mobile fines, and fall deposits, the selective exhumation of deep and well-preserved geologic units has exposed undisturbed outcrops, stratigraphic sections, and structural information much as they are preserved and exposed on Earth. A rich geologic record awaits skilled future field investigators on Mars. The correlation of ground observations and orbital images enables construction of a corresponding geologic reconnaissance map. Most of the outcrops visited are interpreted to be pyroclastic, impactite, and epiclastic deposits overlying an unexposed substrate, probably related to a modified Gusev crater central peak. Fluids have altered chemistry and mineralogy of these protoliths in degrees that vary substantially within the same map unit. Examination of the rocks exposed above and below the major unconformity between the plains lavas and the Columbia Hills directly confirms the general conclusion from remote sensing in previous studies over past years that the early history of Mars was a time of more intense deposition and modification of the surface. Although the availability of fluids and the chemical and mineral activity declined from this early period, significant later volcanism and fluid convection enabled additional, if localized, chemical activity.

Method for the production of mineral wool and iron from serpentine ore

DOEpatents

O'Connor, William K [Albany, OR; Rush, Gilbert E [Scio, OR; Soltau, Glen F [Lebanon, OR

2011-10-11

Magnesium silicate mineral wools having a relatively high liquidus temperature of at least about 1400.degree. C. and to methods for the production thereof are provided. The methods of the present invention comprise melting a magnesium silicate feedstock (e.g., comprising a serpentine or olivine ore) having a liquidus temperature of at least about 1400.degree. C. to form a molten magnesium silicate, and subsequently fiberizing the molten magnesium silicate to produce a magnesium silicate mineral wool. In one embodiment, the magnesium silicate feedstock contains iron oxide (e.g., up to about 12% by weight). Preferably, the melting is performed in the presence of a reducing agent to produce an iron alloy, which can be separated from the molten ore. Useful magnesium silicate feedstocks include, without limitation, serpentine and olivine ores. Optionally, silicon dioxide can be added to the feedstock to lower the liquidus temperature thereof.

Mineralogical Characterization of Fe-Bearing AGB and Supernova Silicate Grains From the Queen Alexandra Range 99177 Meteorite

NASA Technical Reports Server (NTRS)

Nguyen, A. N.; Keller, L. P.; Messenger, S.; Rahman, Z.

2017-01-01

Spectroscopic observations of the circumstellar envelopes of evolved O-rich stars indicate the dust is mostly amorphous silicate with olivine-like compositions. Spectral modeling suggests these grains are Fe-rich [Mg/(Mg+Fe) 0.5], but it is not known whether the Fe is distributed within the silicate matrix or exists as metal inclusions. In contrast, the crystalline silicates are inferred to be extremely Mg-rich [Mg/(Mg+Fe) > 0.95]. The mineralogies and chemical compositions of dust in supernova (SN) remnants are not as well constrained, but abundant silicates of olivine-like and enstatite-like compositions have been fit to the infrared emission features. Silicates in the interstellar medium (ISM) are >99% amor-phous and Fe-bearing. The dearth of crystalline silicates in the ISM requires that some amorphization or destruction mechanisms process these grains.

IN SITU INFRARED MEASUREMENTS OF FREE-FLYING SILICATE DURING CONDENSATION IN THE LABORATORY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ishizuka, Shinnosuke; Kimura, Yuki; Sakon, Itsuki

2015-04-20

We developed a new experimental system for infrared (IR) measurements on free-flying nucleating nanoparticles in situ and applied it to studies on silicate particles. We monitored the condensation of magnesium-bearing silicate nanoparticles from thermally evaporated magnesium and silicon monoxide vapor under an atmosphere of oxygen and argon. The IR spectrum of newly condensed particles showed a spectral feature for non-crystalline magnesium-bearing silicate that is remarkably consistent with the IR spectrum of astronomically observed non-crystalline silicate around oxygen-rich evolved stars. The silicate crystallized at <500 K and eventually developed a high crystallinity. Because of the size effects of nanoparticles, the silicatemore » would be expected to be like a liquid at least during the initial stages of nucleation and growth. Our experimental results therefore suggest decreasing the possible formation temperature of crystalline silicates in dust formation environments with relatively higher pressure.« less

Bimodal Silurian and Lower Devonian volcanic rock assemblages in the Machias-Eastport area, Maine

USGS Publications Warehouse

Gates, Olcott; Moench, R.H.

1981-01-01

Exposed in the Machias-Eastport area of southeastern Maine is the thickest (at least 8,000 m), best exposed, best dated, and most nearly complete succession of Silurian and Lower Devonian volcanic strata in the coastal volcanic belt, remnants of which crop out along the coasts of southern New Brunswick, Canada, and southeastern New England in the United States. The volcanics were erupted through the 600-700-million-year-old Avalonian sialic basement. To test the possibility that this volcanic belt was a magmatic arc above a subduction zone prior to presumed Acadian continental collision, samples representing the entire section in the Machias-Eastport area of Maine were chemically analyzed. Three strongly bimodal assemblages of volcanic rocks and associated intrusives are recognized, herein called the Silurian, older Devonian, and younger Devonian assemblages. The Silurian assemblage contains typically nonporphyritic high-alumina tholeiitic basalts, basaltic andesites, and diabase of continental characterand calc-alkalic rhyolites, silicic dacites, and one known dike of andesite. These rocks are associated with fossiliferous, predominantly marine strata of the Quoddy, Dennys, and Edmunds Formations, and the Leighton Formation of the Pembroke Group (the stratigraphic rank of both is revised herein for the Machias-Eastport area), all of Silurian age. The shallow marine Hersey Formation (stratigraphic rank also revised herein) of the Pembroke Group, of latest Silurian age (and possibly earliest Devonian, as suggested by an ostracode fauna), contains no known volcanics; and it evidently was deposited during a volcanic hiatus that immediately preceded emergence of the coastal volcanic belt and the eruption of the older Devonian assemblage. The older Devonian assemblage, in the lagoonal to subaerial Lower Devonian Eastport Formation, contains tholeiitic basalts and basaltic andesites, typically with abundant plagioclase phenocrysts and typically richer in iron and titanium and poorer in magnesium and nickel than the Silurian basalts; and the Eastport Formation has rhyolites and silicic dacites that have higher average SiO2 and K2O contents and higher ratios of FeO* to MgO than the Silurian ones. The younger Devonian assemblage is represented by one sample of basalt from a flow in red beds of the post-Acadian Upper Devonian Perry Formation, and by three samples from pre-Acadian diabases that intrude the Leighton and Hersey Formations. These rocks are even richer in titanium and iron and poorer in magnesium and nickel than the older Devonian basalts. Post-Acadian granitic plutons exposed along the coastal belt for which analyses are available are tentatively included in the younger Devonian assemblage. The most conspicuous features of the coastal volcanics and associated intrusives are the preponderance of rocks of basaltic composition ( < 52 percent SiO2 ) in the Silurian assemblage, and the near absence in all assemblages of intermediate rocks having 57-67 percent SiO2 (calculated without volatiles). All the rocks are variably altered spilites and keratophyres. The basaltic types are adequately defined, however, by eight samples of least altered basalts having calcic plagioclase, clinopyroxene, and 0.5 percent or less CO2 , The more altered basalts are variably enriched or depleted in Na2O, K2O, and CaO relative to the least altered ones. In the silicic rocks no primary ferromagnesian minerals are preserved. The Na2O and K2O contents of the silicic rocks are erratic; they are approximately reciprocal, possibly owing to alkali exchange while the rocks were still glassy. We propose that the coastal volcanic belt extended along an axis of thermal swelling in the Earth's mantle and upward intrusion of partially melted mantle into the sialic Avalonian crust. These processes were accompanied by shoaling and emergence of the belt, and they produced the bimodal volcanism. Tholeiitic basaltic melts segregated from mantle material

Rice husks as a sustainable silica source for hierarchical flower-like metal silicate architectures assembled into ultrathin nanosheets for adsorption and catalysis.

PubMed

Zhang, Shouwei; Gao, Huihui; Li, Jiaxing; Huang, Yongshun; Alsaedi, Ahmed; Hayat, Tasawar; Xu, Xijin; Wang, Xiangke

2017-01-05

Metal silicates have attracted extensive interests due to their unique structure and promising properties in adsorption and catalysis. However, their applications were hampered by the complex and expensive synthesis. In this paper, three-dimensional (3D) hierarchical flower-like metal silicate, including magnesium silicate, zinc silicate, nickel silicate and cobalt silicate, were for the first time prepared by using rice husks as a sustainable silicon source. The flower-like morphology, interconnected ultrathin nanosheets structure and high specific surface area endowed them with versatile applications. Magnesium silicate was used as an adsorbent with the maximum adsorption capacities of 557.9, 381.3, and 482.8mg/g for Pb 2+ , tetracycline (TC), and UO 2 2+ , respectively. Ni nanoparticles/silica (Ni NPs/SiO 2 ) exhibited high catalytic activity and good stability for 4-nitrophenol (4-NP) reduction within only ∼160s, which can be attributed to the ultra-small particle size (∼6.8nm), good dispersion and high loading capacity of Ni NPs. Considering the abundance and renewability of rice husks, metal silicate with complex architecture can be easily produced at a large scale and become a sustainable and reliable resource for multifunctional applications. Copyright © 2016 Elsevier B.V. All rights reserved.

A comparative study of the continuum and emission characteristics of comet dust. 1: Are the silicates in Comet Halley and Kohoutek amorphous or crystalline

NASA Technical Reports Server (NTRS)

Nansheng, Zhao; Greenberg, J. Mayo; Hage, J. I.

1989-01-01

A continuum emission was subtracted from the 10 micron emission observed towards comets Halley and Kohoutek. The 10 micron excess emissions were compared with BN absorption and laboratory amorphous silicates. The results show that cometary silicates are predominantly amorphous which is consistent with the interstellar dust model of comets. It is concluded that cometary silicates are predominantly similar to interstellar silicates. For a periodic comet like Comet Halley, it is to be expected that some of the silicate may have been heated enough to convert to crystalline form. But apparently, this is only a small fraction of the total. A comparison of Comet Halley silicates with a combination of the crystalline forms observed in interplanetary dust particles (IPDs) seemed reasonable at first sight (Walker 1988, Brownlee 1988). But, if true, it would imply that the total silicate mass in Comet Halley dust is lower than that given by mass spectrometry data of Kissel and Krueger (1987). They estimated m sub org/m sub sil = 0.5 while using crystalline silicate to produce the 10 micron emission would give m sub org/m sub sil = 5 (Greenberg et al. 1988). This is a factor of 10 too high.

Calcium silicate-based drug delivery systems.

PubMed

Zhu, Ying-Jie; Guo, Xiao-Xuan; Sham, Tsun-Kong

2017-02-01

Compared with other inorganic materials such as silica, metal oxides, noble metals and carbon, calcium silicate-based materials, especially nanostructured calcium silicate materials, have high biocompatibility, bioactivity and biodegradability, high specific surface area, nanoporous/hollow structure, high drug-loading capacity, pH-responsive drug release behavior and desirable drug release properties, and thus they are promising for the application in drug delivery. Calcium silicate-based drug delivery systems have a long drug-release time, which can significantly prolong the therapeutic effect of drugs. Another advantage of calcium silicate-based drug delivery systems is their pH-responsive drug release property, which can act as an ideal platform for targeted drug delivery. Areas covered: In recent years, studies have been carried out on calcium silicate-based drug delivery systems, and important results and insights have been documented. This article is not intended to offer a comprehensive review on the research on calcium silicate-based drug delivery systems, but presents some examples reported in the literature, and includes new insights obtained by tracking the interactions between drug molecules and calcium silicate carriers on the molecular level using the synchrotron-based X-ray spectroscopy. Expert opinion: Finally, our opinions on calcium silicate-based drug delivery systems are provided, and several research directions for the future studies are proposed.

Geologic map of the Caetano caldera, Lander and Eureka counties, Nevada

USGS Publications Warehouse

Colgan, Joseph P.; Henry, Christopher D.; John, David A.

2011-01-01

The Eocene (34 Ma) Caetano caldera in north-central Nevada offers an exceptional opportunity to study the physical and petrogenetic evolution of a large (20 km by 10–18 km pre-extensional dimensions) silicic magma chamber, from precursor magmatism to caldera collapse and intrusion of resurgent plutons. Caldera-related rocks shown on this map include two units of crystal-rich intracaldera tuff totaling over 4 km thickness, caldera collapse breccias, tuff dikes that fed the eruption, hydrothermally altered post-eruption rocks, and two generations of resurgent granitic intrusions (John et al., 2008). The map also depicts middle Miocene (about 16–12 Ma) normal faults and synextensional basins that accommodated >100 percent extension and tilted the caldera into a series of ~40° east-dipping blocks, producing exceptional 3-D exposures of the caldera interior (Colgan et al., 2008). This 1:75,000-scale map is a compilation of published maps and extensive new mapping by the authors (fig. 1), and supersedes a preliminary 1:100,000-scale map published by Colgan et al. (2008) and John et al. (2008). New mapping focused on the margins of the Caetano caldera, the distribution and lithology of rocks within the caldera, and on the Miocene normal faults and sedimentary basins that record Neogene extensional faulting. The definition of geologic units and their distribution within the caldera is based entirely on new mapping, except in the northern Toiyabe Range, where mapping by Gilluly and Gates (1965) was modified with new field observations. The distribution of pre-Cenozoic rocks outside the caldera was largely compiled from existing sources with minor modifications, with the exception of the northeastern caldera margin (west of the Cortez Hills Mine), which was remapped in the course of this work and published as a stand-alone 1:6000-scale map (Moore and Henry, 2010).

Geologic map of the Wenatchee 1:100,000 Quadrangle, central Washington

USGS Publications Warehouse

Tabor, R.W.; Waitt, R.B.; Frizzell, V.A.; Swanson, D.A.; Byerly, G.R.; Bentley, R.D.

1982-01-01

The rocks and deposits within the Wenatchee quadrangle can be grouped into six generalized units: (1) Precambrian(?) Swakane Biotite Gneiss in the northeastern part of the quadrangle and the probable Jurassic low-grade metamorphic suite, mostly composed of the Easton Schist, in the southwestern part; (2) the Mesozoic Ingalls Tectonic Complex; (3) the Mesozoic Mount Stuart batholith; (4) lower and middle Tertiary nonmarine sedimentary and volcanic rocks; (5) Miocene basalt flows and interbedded epiclastic rocks constituting part of the Columbia River Basalt Group and interbedded silicic volcaniclastic rocks of the Ellensburg Formation; and (6) Pliocene to Holocene alluvium, glacial, flood, and mass-wastage deposits.

Exposure and vulnerability assessment of buildings extracted from lidar derived datasets in Bucao River floodplains, Zambales, Philippines

NASA Astrophysics Data System (ADS)

Paz-Alberto, Annie Melinda; Ramos, Gloria N.; Espiritu, Jo Adrianne; Mapanao, Kathrina M.; Lao, Ranilo B.

2017-09-01

The Philippines has a geographic and geological setting that make it prone to various hazards including weather and climate-related. It is usually strongly affected by monsoon and typhoon occurrences that cause floods due to torrential rains that causes great risks in man's life and properties, resulting in a significant national loss. Strategies for disaster prevention to protect human lives, properties and social infrastructure is therefore necessary. Different important parameters in disaster risk management such as earth observations, Light Detection and Ranging and Geographic Information System were integrated and utilized in this study. This study dealt with mapping and assessment of buildings that might possibly be exposed and vulnerable to flooding based on the simulated flood maps at different rainfall scenarios in Bucao River Basin. The assessment was done through GIS overlay analysis of the CLSU PHIL-LiDAR 1 Project outputs, the 3D building GIS database and flood hazard maps. Results of this study were series of maps with statistics at different rainfall scenarios. From 23,097 building features extracted, 10,118 buildings, 4,258 buildings and 7,433 buildings were the identified highest number of buildings exposed to flooding and a total of 2,427 buildings, 3,914 buildings and 7,204 buildings from the exposed were identified that had high vulnerabilities in terms of height at low, medium and high hazards of 100 year return period, respectively. Through these maps, it is easier to disseminate information that is more realistic to the residents about the hazardous areas and to help them act on warning and evacuating measures.

Measurement of the efficacy of calcium silicate for the protection and repair of dental enamel.

PubMed

Parker, Alexander S; Patel, Anisha N; Al Botros, Rehab; Snowden, Michael E; McKelvey, Kim; Unwin, Patrick R; Ashcroft, Alexander T; Carvell, Mel; Joiner, Andrew; Peruffo, Massimo

2014-06-01

To investigate the formation of hydroxyapatite (HAP) from calcium silicate and the deposition of calcium silicate onto sound and acid eroded enamel surfaces in order to investigate its repair and protective properties. Calcium silicate was mixed with phosphate buffer for seven days and the resulting solids analysed for crystalline phases by Raman spectroscopy. Deposition studies were conducted on bovine enamel surfaces. Acid etched regions were produced on the enamel surfaces using scanning electrochemical cell microscopy (SECCM) with acid filled pipettes and varying contact times. Following treatment with calcium silicate, the deposition was visualised with FE-SEM and etch pit volumes were measured by AFM. A second set of bovine enamel specimens were pre-treated with calcium silicate and fluoride, before acid exposure with the SECCM. The volumes of the resultant acid etched pits were measured using AFM and the intrinsic rate constant for calcium loss was calculated. Raman spectroscopy confirmed that HAP was formed from calcium silicate. Deposition studies demonstrated greater delivery of calcium silicate to acid eroded than sound enamel and that the volume of acid etched enamel pits was significantly reduced following one treatment (p<0.05). In the protection study, the intrinsic rate constant for calcium loss from enamel was 0.092 ± 0.008 cm/s. This was significantly reduced, 0.056 ± 0.005 cm/s, for the calcium silicate treatments (p<0.0001). Calcium silicate can transform into HAP and can be deposited on acid eroded and sound enamel surfaces. Calcium silicate can provide significant protection of sound enamel from acid challenges. Calcium silicate is a material that has potential for a new approach to the repair of demineralised enamel and the protection of enamel from acid attacks, leading to significant dental hard tissue benefits. © 2014 Elsevier Ltd. All rights reserved.

Mineral stimulation of subsurface microorganisms: release of limiting nutrients from silicates

USGS Publications Warehouse

Roger, Jennifer Roberts; Bennett, Philip C.

2004-01-01

Microorganisms play an important role in the weathering of silicate minerals in many subsurface environments, but an unanswered question is whether the mineral plays an important role in the microbial ecology. Silicate minerals often contain nutrients necessary for microbial growth, but whether the microbial community benefits from their release during weathering is unclear. In this study, we used field and laboratory approaches to investigate microbial interactions with minerals and glasses containing beneficial nutrients and metals. Field experiments from a petroleum-contaminated aquifer, where silicate weathering is substantially accelerated in the contaminated zone, revealed that phosphorus (P) and iron (Fe)-bearing silicate glasses were preferentially colonized and weathered, while glasses without these elements were typically barren of colonizing microorganisms, corroborating previous studies using feldspars. In laboratory studies, we investigated microbial weathering of silicates and the release of nutrients using a model ligand-promoted pathway. A metal-chelating organic ligand 3,4 dihydroxybenzoic acid (3,4 DHBA) was used as a source of chelated ferric iron, and a carbon source, to investigate mineral weathering rate and microbial metabolism.In the investigated aquifer, we hypothesize that microbes produce organic ligands to chelate metals, particularly Fe, for metabolic processes and also form stable complexes with Al and occasionally with Si. Further, the concentration of these ligands is apparently sufficient near an attached microorganism to destroy the silicate framework while releasing the nutrient of interest. In microcosms containing silicates and glasses with trace phosphate mineral inclusions, microbial biomass increased, indicating that the microbial community can use silicate-bound phosphate inclusions. The addition of a native microbial consortium to microcosms containing silicates or glasses with iron oxide inclusions correlated to accelerated weathering and release of Si into solution as well as the accelerated degradation of the model substrate 3,4 DHBA. We propose that silicate-bound P and Fe inclusions are bioavailable, and microorganisms may use organic ligands to dissolve the silicate matrix and access these otherwise limiting nutrients.

Predicting the Sources and Formation Mechanisms of Evolved Lunar Crust by Linking K/Ca Ratios of Lunar Granites to Analogous Terrestrial Igneous Rocks

NASA Technical Reports Server (NTRS)

Mills, R. D.; Simon, J. I.

2012-01-01

Although silicic rocks (i.e. granites and rhyolites) comprise a minor component of the sampled portion of the lunar crust, recent remote sensing studies [e.g., 1-4] indicate that several un-sampled regions of the Moon have significantly higher concentrations of silicic material (also high in [K], [U], and [Th]) than sampled regions. Within these areas are morphological features that are best explained by the existence of chemically evolved volcanic rocks. Observations of silicic domes [e.g., 1-5] suggest that sizable networks of silicic melt were present during crust formation. Isotopic data indicate that silicic melts were generated over a prolonged timespan from 4.3 to 3.9 Ga [e.g., 6-8]. The protracted age range and broad distribution of silicic rocks on the Moon indicate that their petrogenesis was an important mechanism for secondary crust formation. Understanding the origin and evolution of such silicic magmas is critical to determining the composition of the lunar crustal highlands and will help to distinguish between opposing ideas for the Moon's bulk composition and differentiation. The two main hypotheses for generating silicic melts on Earth are fractional crystallization or partial melting. On the Moon silicic melts are thought to have been generated during extreme fractional crystallization involving end-stage silicate liquid immiscibility (SLI) [e.g. 9, 10]. However, SLI cannot account for the production of significant volumes of silicic melt and its wide distribution, as reported by the remote global surveys [1, 2, 3]. In addition, experimental and natural products of SLI show that U and Th, which are abundant in the lunar granites and seen in the remote sensing data of the domes, are preferentially partitioned into the depolymerized ferrobasaltic magma and not the silicic portion [11, 12]. If SLI is not the mechanism that generated silicic magmas on the Moon then alternative processes such as fractional crystallization (only crystal-liquid separation) or partial melting should be considered as viable possibilities to be tested.

Final report on the safety assessment of potassium silicate, sodium metasilicate, and sodium silicate.

PubMed

Elmore, Amy R

2005-01-01

Potassium Silicate, Sodium Metasilicate, and Sodium Silicate combine metal cations with silica to form inorganic salts used as corrosion inhibitors in cosmetics. Sodium Metasilicate also functions as a chelating agent and Sodium Silicate as a buffering and pH adjuster. Sodium Metasilicate is currently used in 168 formulations at concentrations ranging from 13% to 18%. Sodium Silicate is currently used in 24 formulations at concentrations ranging from 0.3% to 55%. Potassium Silicate and Sodium Silicate have been reported as being used in industrial cleaners and detergents. Sodium Metasilicate is a GRAS (generally regarded as safe) food ingredient. Aqueous solutions of Sodium Silicate species are a part of a chemical continuum of silicates based on an equilibrium of alkali, water, and silica. pH determines the solubility of silica and, together with concentration, determines the degree of polymerization. Sodium Silicate administered orally is readily absorbed from the alimentary canal and excreted in the urine. The toxicity of these silicates has been related to the molar ratio of SiO2/Na2O and the concentration being used. The Sodium Metasilicate acute oral LD50 ranged from 847 mg/kg in male rats to 1349.3 mg/kg in female rats and from 770 mg/kg in female mice to 820 mg/kg in male mice. Gross lesions of variable severity were found in the oral cavity, pharynx, esophagus, stomach, larynx, lungs, and kidneys of dogs receiving 0.25 g/kg or more of a commercial detergent containing Sodium Metasilicate; similar lesions were also seen in pigs administered the same detergent and dose. Male rats orally administered 464 mg/kg of a 20% solution containing either 2.0 or 2.4 to 1.0 ratio of sodium oxide showed no signs of toxicity, whereas doses of 1000 and 2150 mg/kg produced gasping, dypsnea, and acute depression. Dogs fed 2.4 g/kg/day of Sodium Silicate for 4 weeks had gross renal lesions but no impairment of renal function. Dermal irritation of Potassium Silicate, Sodium Metasilicate, and Sodium Silicate ranged from negligible to severe, depending on the species tested and the molar ratio and concentration tested. Sodium Metasilicate was negative in the local lymph node assay (LLNA), but a delayed-type hypersensitivity response was observed in mice. Potassium Silicate was nonirritating in two acute eye irritation studies in rabbits. Sodium Metasilicate (42.4% H2O) was corrosive to the rabbit eye. Sodium Silicate was a severe eye irritant in some eye irritation studies, but was irritating or nonirritating in others. A skin freshener containing Sodium Silicate was nonirritating. Sodium Metasilicate was nonmutagenic in bacterial cells. Rats given Sodium Silicate (600 and 1200 ppm of added silica) in the drinking water in reproductive studies produced a reduced number of offspring: to 67% of controls at 600 ppm and to 80% of controls at 1200 ppm. Three adult rats injected intratesticularly and subcutaneously with 0.8 mM/kg of Sodium Silicate showed no morphological changes in the testes and no effect on the residual spermatozoa in the ductus deferens. Sodium Metasilicate (37% in a detergent) mixed with water was a severe skin irritant when tested on intact and abraded human skin, but 6%, 7%, and 13% Sodium Silicate were negligible skin irritants to intact and abraded human skin. Sodium Silicate (10% of a 40% aqueous solution) was negative in a repeat-insult predictive patch test in humans. The same aqueous solution of Sodium Silicate was considered a mild irritant under normal use conditions in a study of cumulative irritant properties. The Cosmetic Ingredient Review (CIR) Expert Panel recognized the irritation potential of these ingredients, especially in leave-on products. However, because these ingredients have limited dermal absorption and Sodium Metasilicate is a GRAS direct food substance, the Panel deemed the ingredients safe for use in cosmetic products in the practices of use and concentration described in this safety assessment, when formulated to avoid irritation.

Geologic Map of the Weaverville 15' Quadrangle, Trinity County, California

USGS Publications Warehouse

Irwin, William P.

2009-01-01

The Weaverville 15' quadrangle spans parts of five generally north-northwest-trending accreted terranes. From east to west, these are the Eastern Klamath, Central Metamorphic, North Fork, Eastern Hayfork, and Western Hayfork terranes. The Eastern Klamath terrane was thrust westward over the Central Metamorphic terrane during early Paleozoic (Devonian?) time and, in Early Cretaceous time (approx. 136 Ma), was intruded along its length by the massive Shasta Bally batholith. Remnants of overlap assemblages of the Early Cretaceous (Hauterivian) Great Valley sequence and the Tertiary Weaverville Formation cover nearly 10 percent of the quadrangle. The base of the Eastern Klamath terrane in the Weaverville quadrangle is a peridotite-gabbro complex that probably is correlative to the Trinity ophiolite (Ordovician), which is widely exposed farther north beyond the quadrangle. In the northeast part of the Weaverville quadrangle, the peridotite-gabbro complex is overlain by the Devonian Copley Greenstone and the Mississippian Bragdon Formation. Where these formations were intruded by the Shasta Bally batholith, they formed an aureole of gneissic and other metamorphic rocks around the batholith. Westward thrusting of the Eastern Klamath terrane over an adjacent body of mafic volcanic and overlying quartzose sedimentary rocks during Devonian time formed the Salmon Hornblende Schist and the Abrams Mica Schist of the Central Metamorphic terrane. Substantial beds of limestone in the quartzose sedimentary unit, generally found near the underlying volcanic rock, are too metamorphosed for fossils to have survived. Rb-Sr analysis of the Abrams Mica Schist indicates a metamorphic age of approx. 380 Ma. West of Weavervillle, the Oregon Mountain outlier of the Eastern Klamath terrane consists mainly of Bragdon Formation(?) and is largely separated from the underlying Central Metamorphic terrane by serpentinized peridotite that may be a remnant of the Trinity ophiolite. The North Fork terrane is faulted against the west edge of the Central Metamorphic terrane, and its northerly trend is disrupted by major left-lateral offsets along generally west-northwest-trending faults. The serpentinized peridotite-gabbro complex that forms the western base of the terrane is the Permian North Fork ophiolite, which to the east is overlain by broken formation of mafic-volcanic rocks, red chert, siliceous tuff, argillite, minor limestone, and clastic sedimentary rocks. The chert and siliceous tuff contain radiolarians of Permian and Mesozoic ages, and some are as young as Early Jurassic (Pliensbachian). Similar Pliensbachian radiolarians are found in Franciscan rocks of the Coast Ranges. The Eastern Hayfork terrane is broken formation and melange of mainly chert, sandstone, argillite, and various exotic blocks. The cherts yield radiolarians of Permian and Triassic ages but none of clearly Jurassic age. Limestone bodies of the Eastern Hayfork terrane contain Permian microfaunas of Tethyan affinity. The Western Hayfork terrane, exposed only in a small area in the southwestern part of the quadrangle, consists dominantly of mafic tuff and dark slaty argillite. Sparse paleontologic data indicate a Mesozoic age for the strata. The terrane includes small bodies of diorite that are related to the nearby Wildwood pluton of Middle Jurassic age and probably are related genetically to the stratified rocks. The terrane is interpreted to be the accreted remnants of a Middle Jurassic volcanic arc. Shortly after intrusion by Shasta Bally batholith (approx. 136 Ma), much of the southern half of the Weaverville quadrangle was overlapped by Lower Cretaceous, dominantly Hauterivian, marine strata of the Great Valley sequence, and to a lesser extent later during Oligocene and (or) Miocene time by fluvial and lacustrine deposits of the Weaverville Formation. This map of the Weaverville Quadrangle is a digital rendition of U.S. Geological Survey Miscellaneous Field

40 CFR 180.1268 - Potassium silicate; exemption from the requirement of a tolerance.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 24 2014-07-01 2014-07-01 false Potassium silicate; exemption from the... Exemptions From Tolerances § 180.1268 Potassium silicate; exemption from the requirement of a tolerance. Potassium silicate is exempt from the requirement of a tolerance in or on all food commodities so long as...

40 CFR 180.1268 - Potassium silicate; exemption from the requirement of a tolerance.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 25 2012-07-01 2012-07-01 false Potassium silicate; exemption from the... Exemptions From Tolerances § 180.1268 Potassium silicate; exemption from the requirement of a tolerance. Potassium silicate is exempt from the requirement of a tolerance in or on all food commodities so long as...

40 CFR 180.1268 - Potassium silicate; exemption from the requirement of a tolerance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Potassium silicate; exemption from the... Exemptions From Tolerances § 180.1268 Potassium silicate; exemption from the requirement of a tolerance. Potassium silicate is exempt from the requirement of a tolerance in or on all food commodities so long as...

40 CFR 180.1268 - Potassium silicate; exemption from the requirement of a tolerance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 25 2013-07-01 2013-07-01 false Potassium silicate; exemption from the... Exemptions From Tolerances § 180.1268 Potassium silicate; exemption from the requirement of a tolerance. Potassium silicate is exempt from the requirement of a tolerance in or on all food commodities so long as...

40 CFR 180.1268 - Potassium silicate; exemption from the requirement of a tolerance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Potassium silicate; exemption from the... Exemptions From Tolerances § 180.1268 Potassium silicate; exemption from the requirement of a tolerance. Potassium silicate is exempt from the requirement of a tolerance in or on all food commodities so long as...

Soft X-Ray Irradiation of Silicates: Implications for Dust Evolution in Protoplanetary Disks

NASA Astrophysics Data System (ADS)

Ciaravella, A.; Cecchi-Pestellini, C.; Chen, Y.-J.; Muñoz Caro, G. M.; Huang, C.-H.; Jiménez-Escobar, A.; Venezia, A. M.

2016-09-01

The processing of energetic photons on bare silicate grains was simulated experimentally on silicate films submitted to soft X-rays of energies up to 1.25 keV. The silicate material was prepared by means of a microwave assisted sol-gel technique. Its chemical composition reflects the Mg2SiO4 stoichiometry with residual impurities due to the synthesis method. The experiments were performed using the spherical grating monochromator beamline at the National Synchrotron Radiation Research Center in Taiwan. We found that soft X-ray irradiation induces structural changes that can be interpreted as an amorphization of the processed silicate material. The present results may have relevant implications in the evolution of silicate materials in X-ray-irradiated protoplanetary disks.

Epithermal mineralization controlled by synextensional magmatism in the Guazapares Mining District of the Sierra Madre Occidental silicic large igneous province, Mexico

NASA Astrophysics Data System (ADS)

Murray, Bryan P.; Busby, Cathy J.

2015-03-01

We show here that epithermal mineralization in the Guazapares Mining District is closely related to extensional deformation and magmatism during the mid-Cenozoic ignimbrite flare-up of the Sierra Madre Occidental silicic large igneous province, Mexico. Three Late Oligocene-Early Miocene synextensional formations are identified by detailed volcanic lithofacies mapping in the study area: (1) ca. 27.5 Ma Parajes formation, composed of silicic outflow ignimbrite sheets; (2) ca. 27-24.5 Ma Témoris formation, consisting primarily of locally erupted mafic-intermediate composition lavas and interbedded fluvial and debris flow deposits; (3) ca. 24.5-23 Ma Sierra Guazapares formation, composed of silicic vent to proximal ignimbrites, lavas, subvolcanic intrusions, and volcaniclastic deposits. Epithermal low-to intermediate-sulfidation, gold-silver-lead-zinc vein and breccia mineralization appears to be associated with emplacement of Sierra Guazapares formation rhyolite plugs and is favored where pre-to-synvolcanic extensional structures are in close association with these hypabyssal intrusions. Several resource areas in the Guazapares Mining District are located along the easternmost strands of the Guazapares Fault Zone, a NNW-trending normal fault system that hosts most of the epithermal mineralization in the mining district. This study describes the geology that underlies three of these areas, which are, from north to south: (1) The Monte Cristo resource area, which is underlain primarily by Sierra Guazapares formation rhyolite dome collapse breccia, lapilli-tuffs, and fluvially reworked tuffs that interfinger with lacustrine sedimentary rocks in a synvolcanic half-graben bounded by the Sangre de Cristo Fault. Deposition in the hanging wall of this half-graben was concurrent with the development of a rhyolite lava dome-hypabyssal intrusion complex in the footwall; mineralization is concentrated in the high-silica rhyolite intrusions in the footwall and along the syndepositional fault and adjacent hanging wall graben fill. (2) The San Antonio resource area, underlain by interstratified mafic-intermediate lavas and fluvial sandstone of the Témoris formation, faulted and tilted by two en echelon NW-trending normal faults with opposing dip-directions. Mineralization occurs along subvertical structures in the accommodation zone between these faults. There are no silicic intrusions at the surface within the San Antonio resource area, but they outcrop ˜0.5 km to the east, where they are intruded along the La Palmera Fault, and are located ˜120 m-depth in the subsurface. (3) The La Unión resource area, which is underlain by mineralized andesite lavas and lapilli-tuffs of the Témoris Formation. Adjacent to the La Unión resource area is Cerro Salitrera, one of the largest silicic intrusions in the area. The plug that forms Cerro Salitrera was intruded along the La Palmera Fault, and was not recognized as an intrusion prior to our work. We show here that epithermal mineralization is Late Oligocene to Miocene-age and hosted in extensional structures, younger than Laramide (Cretaceous-Eocene) ages of mineralization inferred from unpublished mining reports for the region. We further infer that mineralization was directly related to the emplacement of silicic intrusions of the Sierra Guazapares formation, when the mid-Cenozoic ignimbrite flare-up of the Sierra Madre Occidental swept westward into the study area about 24.5-23 Ma ago.

3D Observation of GEMS by Electron Tomography

NASA Technical Reports Server (NTRS)

Matsuno, Junya; Miyake, Akira; Tsuchiyama, Akira; Nakamura-Messenger, Keiko; Messenger, Scott

2014-01-01

Amorphous silicates in chondritic porous interplanetary dust particles (CP-IDPs) coming from comets are dominated by glass with embedded metal and sulfides (GEMS). GEMS grains are submicron-sized rounded objects (typically 100-500) nm in diameter) with anaometer-sized (10-50 nm) Fe-Ni metal and sulfide grains embedded in an amorphous silicate matrix. Several formation processes for GEMS grains have been proposed so far, but these models are still being debated [2-5]. Bradley et al. proposed that GEMS grains are interstellar silicate dust that survived various metamorphism or alteration processes in the protoplanetary disk and that they are amorphiation products of crystalline silicates in the interstellar medium by sputter-deposition of cosmic ray irradiation, similar to space weathering [2,4]. This consideration is based on the observation of nano-sized crystals (approximately 10 nm) called relict grains in GEMS grains and their shapes are pseudomorphs to the host GEMS grains. On the other hand, Keller and Messenger proposed that most GEMS formed in the protoplanetary disk as condensates from high temperature gas [3,5]. This model is based on the fact that most GEMS grains have solar isotopic compositions and have extremely heterogeneous and non-solar elemental compositions. Keller and Messenger (2011) also reported that amorphous silicates in GEMS grains are surrounded by sulfide grains, which formed as sulfidization of metallic iron grains located on the GEMS surface. The previous studies were performed with 2D observation by using transmission electron microscopy (TEM) or scanning TEM (STEM). In order to understand the structure of GEMS grains described above more clearly, we observed 3D structure of GEMS grains by electron tomography using a TEM/STEM (JEM-2100F, JEOL) at Kyoto University. Electron tomography gives not only 3D structures but also gives higher spatial resolution (approximately a few nm) than that in conventional 2D image, which is restricted by sample thickness ) approx. or greater than 50 nm). Three cluster IDPs (L2036AA5 cluster4, L2009L8 cluster 13 and W726A2) were used for the observations. ID W726A2 was collected without silicon oil, which is ordinary used to collect IDPs, so this sample has no possibility of contaminations caused by silicon oil or solvent to rinse it [6]. The samples were embedded in epoxy risin and sliced into ultrathin sections (50-300 nm) using an ultramicotome. The sections were observed by BF-TEM and HAADF-STEM (high angle annular dark field-scanning TEM) modes. Images were obtained by rotating the sample tilt angle over a range of +/- 65 deg in 1 deg steps. The obtained images were reconstructed to slice images. Mineral phases in the slice images were estimated by comparing with a 2D elemental map obtained by an EDS (energy dispersive X-ray spectroscopy) system equipped in the TEM/STEM. Careful examination of the slice images confirmed that iron grains are embedded in the amorphous silicate matrix of the GEMS grains, but sulfide grains were mainly present on the surface of the amorphous silicate. These results are consistent with the model that GEMS grains formed as condensates [3,5], although more data are needed to conclude the origin of GEMS grains. The present study is the first successful example adapting the electron tomography to the IDPs. This type of analysis will be important for planetary material sciences in the future.

Investigation of the H7 ordinary chondrite, Watson 012: Implications for recognition and classification of Type 7 meteorites

NASA Astrophysics Data System (ADS)

Tait, Alastair W.; Tomkins, Andrew G.; Godel, Bélinda M.; Wilson, Siobhan A.; Hasalova, Pavlina

2014-06-01

Despite the fact that the number of officially classified meteorites is now over 45,000, we lack a clearly defined sequence of samples from a single parent body that records the entire range in metamorphic temperatures from pristine primitive meteorites up to the temperatures required for extensive silicate partial melting. Here, we conduct a detailed analysis of Watson 012, an H7 ordinary chondrite, to generate some clarity on the textural and chemical changes associated with equilibrium-based silicate partial melting in chondritic meteorites. To do this we compare the textures in the meteorite with those preserved in metamorphic contact aureoles on Earth. The most distinctive texture generated by the partial melting that affected Watson 012 is an extensively interconnected plagioclase network, which is clearly observable with a petrographic microscope. Enlarged metal-troilite grains are encapsulated at widenings in this plagioclase network, and this is clearly visible in reflected light. Together with these features, we define a series of other characteristics that can be used to more clearly classify chondritic meteorites as being of petrologic Type 7. To provide comprehensive evidence of silicate partial melting and strengthen the case for using simple petrographic observations to classify similar meteorites, we use high-resolution X-ray computed tomography to demonstrate that the plagioclase network has a high degree of interconnectedness and crystallised as large (cm-scale) skeletal crystals within an olivine-orthopyroxene-clinopyroxene framework, essentially pseudomorphing a melt network. Back-scattered electron imaging and element mapping are used to show that some of the clino- and orthopyroxene in Watson 012 also crystallised from silicate melt, and the order of crystallisation was orthopyroxene → clinopyroxene → plagioclase. X-ray diffraction data, supported by bulk geochemistry, are used to show that plagioclase and ortho- and clinopyroxene were added to the Watson 012 sample by through-flowing basaltic melt. Along with the absence of glass and granophyre, this interconnected network of coarse-grained skeletal plagioclase indicates that the sample cooled slowly at depth within the parent body. The evidence of melt flux indicates that Watson 012 formed in the presence of a gravitational gradient, and thus at significant distance from the centre of the H chondrite parent body (the gravitational gradient at the centre would be zero). Our interpretation is that incipient silicate partial melting in Watson 012 occurred when a region of radiogenically heated H6 material located at considerable depth (possibly at ∼15-20 km from surface) was heated by an additional ca. 200-300 °C in association with a large shock event. Due to insulation at depth within an already hot parent body, the post-shock temperature equilibrated and remained above the solidus long enough for widespread equilibrium-based silicate partial melting, and for melt to migrate. Although the observed melting may have been facilitated by additional heating from an impact event, this is not an example of instantaneous shock melting, which produces thermal disequilibrium at short length scales and distinctly different textures. A small number of H, L and LL chondrites have been previously classified as being of petrologic Type 7; with our new criteria to support that classification, these represent our best opportunity to explore the transition from high temperature sub-solidus metamorphism through the onset of silicate partial melting in three different parent bodies.

Fundamental Studies on Crashworthiness Design with Uncertainties in the System

DTIC Science & Technology

2005-01-01

studied; examples include using the Response Surface Methods (RSM) and Design of Experiment (DOE) [2-4]. Space Mapping (SM) is another practical...Exposed to Impact Load Using a Space Mapping Technique,” Struct. Multidisc. Optim., Vol. 27, pp. 411-420 (2004). 6. Mayer, R. R., Kikuchi, N. and Scott

Mapping coastal vegetation, land use and environmental impact from ERTS-1. [Delaware coastal zone

NASA Technical Reports Server (NTRS)

Klemas, V. (Principal Investigator)

1973-01-01

The author has identified the following significant results. Digital analysis of ERTS-1 imagery was used in an attempt to map and inventory the significant ecological communities of Delaware's coastal zone. Eight vegetation and land use discrimination classes were selected: (1) Phragmites communis (giant reed grass); (2) Spartina alterniflora (salt marsh cord grass); (3) Spartina patens (salt marsh hay); (4) shallow water and exposed mud; (5) deep water (greater than 2 m); (6) forest; (7) agriculture; and (8) exposed sand and concrete. Canonical analysis showed the following classification accuracies: Spartina alterniflora, exposed sand, concrete, and forested land - 94% to 100%; shallow water - mud and deep water - 88% and 93% respectively; Phragmites communis 83%; Spartina patens - 52%. Classification accuracy for agriculture was very poor (51%). Limitations of time and available class-memory space resulted in limiting the analysis of agriculture to very gross identification of a class which actually consists of many varied signature classes. Abundant ground truth was available in the form of vegetation maps compiled from color and color infrared photographs. It is believed that with further refinement of training set selection, sufficiently accurate results can be obtained for all categories.

Light scattering and absorption by space weathered planetary bodies: Novel numerical solution

NASA Astrophysics Data System (ADS)

Markkanen, Johannes; Väisänen, Timo; Penttilä, Antti; Muinonen, Karri

2017-10-01

Airless planetary bodies are exposed to space weathering, i.e., energetic electromagnetic and particle radiation, implantation and sputtering from solar wind particles, and micrometeorite bombardment.Space weathering is known to alter the physical and chemical composition of the surface of an airless body (C. Pieters et al., J. Geophys. Res. Planets, 121, 2016). From the light scattering perspective, one of the key effects is the production of nanophase iron (npFe0) near the exposed surfaces (B. Hapke, J. Geophys. Res., 106, E5, 2001). At visible and ultraviolet wavelengths these particles have a strong electromagnetic response which has a major impact on scattering and absorption features. Thus, to interpret the spectroscopic observations of space-weathered asteroids, the model should treat the contributions of the npFe0 particles rigorously.Our numerical approach is based on the hierarchical geometric optics (GO) and radiative transfer (RT). The modelled asteroid is assumed to consist of densely packed silicate grains with npFe0 inclusions. We employ our recently developed RT method for dense random media (K. Muinonen, et al., Radio Science, submitted, 2017) to compute the contributions of the npFe0 particles embedded in silicate grains. The dense media RT method requires computing interactions of the npFe0 particles in the volume element for which we use the exact fast superposition T-matrix method (J. Markkanen, and A.J. Yuffa, JQSRT 189, 2017). Reflections and refractions on the grain surface and propagation in the grain are addressed by the GO. Finally, the standard RT is applied to compute scattering by the entire asteroid.Our numerical method allows for a quantitative interpretation of the spectroscopic observations of space-weathered asteroids. In addition, it may be an important step towards more rigorous a thermophysical model of asteroids when coupled with the radiative and conductive heat transfer techniques.Acknowledgments. Research supported by European Research Council with Advanced Grant No. 320773 SAEMPL. Computational resources provided by CSC- IT Centre for Science Ltd, Finland.

Investigating the Source of Water and/or Hydroxyl on Asteroid (16) Psyche

NASA Astrophysics Data System (ADS)

Takir, D.; Reddy, V.; Sanchez, J. A.; Shepard, M. K.; Emery, J. P.

2017-12-01

Asteroid (16) Psyche will be visited by the Psyche mission, which was selected by NASA and will be launched in 2022 as the 14th Discovery mission. Psyche is thought to be one of the most massive exposed metallic core in the asteroid belt. The high radar albedos, thermal inertia, and density of Psyche revealed that this asteroid is composed of almost entirely of Fe-Ni metal. Psyche is also characterized by moderately red spectra and the presence of weak features (attributed to silicates) in the visible and near-infrared (NIR) region (0.3-2.5 µm). Recent NIR observations also showed rotational spectral variations indicating a possible change in the metal/silicate ratio on the surface of this asteroid. Additionally, we observed Psyche in the 3-µm spectral region using the long-wavelength cross-dispersed (LXD: 1.9-4.2 µm) mode of the SpeX spectrograph/imager at the NASA Infrared Telescope Facility (IRTF). Our observations revealed that Psyche exhibits a 3-µm feature, more likely attributed to water- and/or hydroxyl molecules. While the source of water and/or hydroxyl on Psyche remains unclear, we proposed a few possible mechanisms for their formation: (1) the water/hydroxyl-rich materials detected on Psyche might have been delivered to its surface by carbonaceous impactors (like on Vesta), (2) Psyche may not be entirely exposed metallic, instead, its surface has a core-mantle boundary of a differentiated body that was disrupted by impacts (e.g., Pallasite-like), or (3) the water/hydroxyl-rich materials detected on Psyche is produced by Solar wind implantation (like on the Moon). In this talk we will discuss these three possible mechanisms and hypotheses and how they can be tested prior to the launch of the Psyche spacecraft using predictive laboratory measurements and modeling, and during the spacecraft encounter with the asteroid using the mission main instruments that will include the multispectral imagers, the gamma-ray and neutron spectrometer, and the dual fluxgate magnetometers.

Efficacy of Erbium, Chromium-doped:Yttrium, Scandium, Gallium, and Garnet Laser Irradiation Combined with Resin-based Tricalcium Silicate and Calcium Hydroxide on Direct Pulp Capping: A Randomized Clinical Trial.

PubMed

Cengiz, Esra; Yilmaz, Hasan Guney

2016-03-01

The purpose of this randomized clinical study was to evaluate the efficiency of erbium, chromium-doped:yttrium, scandium, gallium, and garnet (Er,Cr:YSGG) laser irradiation combined with a resin-based tricalcium silicate material and calcium hydroxide in direct pulp capping for a 6-month follow-up period. A total of 60 teeth of 60 patients between the ages of 18 and 41 years were recruited for this study. Sixty permanent vital teeth without symptoms and radiographic changes were randomly assigned to the following 4 groups (n = 15): Gr CH, the exposed area was sealed with calcium hydroxide (CH) paste; Gr laser CH, the treated area was sealed with CH paste after Er,Cr:YSGG laser irradiation at an energy level of 0.5 W without water and with 45% air; Gr TheraCal, TheraCal LC (Bisco, Schaumburg, IL) was applied directly to the exposed pulp; and Gr Laser TheraCal, TheraCal LC was applied after irradiation with an Er,Cr:YSGG laser. At the 1-week and 1-, 3-, and 6-month recall examinations, the loss of vitality, spontaneous pain, reactions to thermal stimuli and percussion, and radiographic changes were considered as failure. The success rates in the CH and TheraCal groups were 73.3% and 66.6%, respectively. These rates did not reveal any significant difference. In both laser groups, success rates were 100%. The Er,Cr:YSGG laser-irradiated TheraCal and Er,Cr:YSGG laser-irradiated CH groups showed statistically higher success rates than the TheraCal and CH groups, respectively. Er,Cr:YSGG laser irradiation at 0.5 W without water combined with pulp capping agents can be recommended for direct pulp therapy. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Experimentation of cooperative learning model Numbered Heads Together (NHT) type by concept maps and Teams Games Tournament (TGT) by concept maps in terms of students logical mathematics intellegences

NASA Astrophysics Data System (ADS)

Irawan, Adi; Mardiyana; Retno Sari Saputro, Dewi

2017-06-01

This research is aimed to find out the effect of learning model towards learning achievement in terms of students’ logical mathematics intelligences. The learning models that were compared were NHT by Concept Maps, TGT by Concept Maps, and Direct Learning model. This research was pseudo experimental by factorial design 3×3. The population of this research was all of the students of class XI Natural Sciences of Senior High School in all regency of Karanganyar in academic year 2016/2017. The conclusions of this research were: 1) the students’ achievements with NHT learning model by Concept Maps were better than students’ achievements with TGT model by Concept Maps and Direct Learning model. The students’ achievements with TGT model by Concept Maps were better than the students’ achievements with Direct Learning model. 2) The students’ achievements that exposed high logical mathematics intelligences were better than students’ medium and low logical mathematics intelligences. The students’ achievements that exposed medium logical mathematics intelligences were better than the students’ low logical mathematics intelligences. 3) Each of student logical mathematics intelligences with NHT learning model by Concept Maps has better achievement than students with TGT learning model by Concept Maps, students with NHT learning model by Concept Maps have better achievement than students with the direct learning model, and the students with TGT by Concept Maps learning model have better achievement than students with Direct Learning model. 4) Each of learning model, students who have logical mathematics intelligences have better achievement then students who have medium logical mathematics intelligences, and students who have medium logical mathematics intelligences have better achievement than students who have low logical mathematics intelligences.

Geologic map of the Lazy Y Point Quadrangle, Moffat County Colorado

USGS Publications Warehouse

Van Loenen, R. E.; Selner, G.I.; Bryant, W.A.

1999-01-01

The Lazy Y Point quadrangle is in northwestern Colorado a few miles north of Rangely. The prominent structural feature of the Lazy Y Point quadrangle is the Skull Creek monocline. Pennsylvanian rocks are exposed along the axis of the monocline while hogbacks along its southern flank expose rocks that are from Permian to Upper Cretaceous in age. The Wolf Creek monocline and the Wolf Creek thrust fault, which dissects the monocline, are salient structural features in the northern part of the quadrangle. Little or no mineral potential exists within the quadrangle. A geologic map of the Skull Creek quadrangle, which is adjacent to the Lazy Y Point quadrangle on the east, is also available (Geologic Investigations Series I-2647). This companian map shows similar geologic features, including the eastern half of the Skull Creek monocline. The geology of this quadrangle was mapped because of its proximity to Dinosaur National Monument. It is adjacent to quadrangles previously mapped to display the geology of this very scenic and popular National Monument. The Lazy Y Point quadrangle includes parts of the Willow and Skull Creek Wilderness Study Areas, which were assessed for their mineral resource potential.

Wind driven saltation: a hitherto overlooked challenge for life on Mars

NASA Astrophysics Data System (ADS)

Bak, Ebbe; Goul, Michael; Rasmussen, Martin; Moeller, Ralf; Nørnberg, Per; Knak Jensen, Svend; Finster, Kai

2017-04-01

The Martian surface is a hostile environment characterized by low water availability, low atmospheric pressure and high UV and ionizing radiation. Furthermore, wind-driven saltation leads to abrasion of silicates with a production of reactive surface sites and, through triboelectric charging, a release of electrical discharges with a concomitant production of reactive oxygen species. While the effects of low water availability, low pressure and radiation have been extensively studied in relation to the habitability of the Martian surface and the preservation of organic biosignatures, the effects of wind-driven saltation have hitherto been ignored. In this study, we have investigated the effect of exposing bacteria to wind-abraded silicates and directly to wind-driven saltation on Mars in controlled laboratory simulation experiments. Wind-driven saltation was simulated by tumbling mineral samples in a Mars-like atmosphere in sealed quartz ampoules. The effects on bacterial survival and structure were evaluated by colony forming unit counts in combination with scanning electron microscopy, quantitative polymerase chain reaction and life/dead-staining with flow cytometry. The viability of vegetative cells of P. putida, B. subtilis and D. radiodurans in aqueous suspensions was reduced by more than 99% by exposure to abraded basalt, while the viability of B. subtilis endospores was unaffected. B. subtilis mutants lacking different spore components were likewise highly resistant to the exposure to abraded basalt, which indicates that the resistance of spores is not associated with any specific spore component. We found a significant but reduced effect of abraded quartz and we suggest that the stress effect of abraded silicates is induced by a production of reactive oxygen species and hydroxyl radicals produced by Fenton-like reactions in the presence of transition metals. Direct exposure to simulated saltation had a dramatic effect on both D. radiodurans cells and B. subtilis spore with a more than 99.9% decrease in survival after 17 days. The high susceptibility of the usually multi-resistant D. radiodurans cells and B. sublitis spores to the effects of wind-driven saltation indicates that wind abraded silicates as well as direct exposure to saltation represent a considerable stress for microorganisms at the Martian surface, which may have limited the chance of indigenous life, could limit the risk of forward contamination and may have degraded potential organic biosignatures.

Amorphous Silicate Smokes as Catalysts for the Production of Complex Organic Species in the Primitive Solar Nebula

NASA Technical Reports Server (NTRS)

Nuth, J. A., III; Hill, H. G. M.

2002-01-01

Amorphous Mg-silicates are excellent Fischer-Tropsch catalysts that convert H2 and CO into hydrocarbons almost as well as Fe-silicates. Mg-silicates do not catalyze formation of ammonia. N is incorporated into the organics if CO, N2 and H2 are used. Additional information is contained in the original extended abstract.

FE and MG Isotopic Analyses of Isotopically Unusual Presolar Silicate Grains

NASA Technical Reports Server (NTRS)

Nguyen, A. N.; Messenger, S.; Ito, M.; Rahman, Z.

2011-01-01

Interstellar and circumstellar silicate grains are thought to be Mg-rich and Fe-poor, based on astronomical observations and equilibrium condensation models of silicate dust formation in stellar outflows. On the other hand, presolar silicates isolated from meteorites have surprisingly high Fe contents and few Mg-rich grains are observed. The high Fe contents in meteoritic presolar silicates may indicate they formed by a non-equilibrium condensation process. Alternatively, the Fe in the stardust grains could have been acquired during parent body alteration. The origin of Fe in presolar silicates may be deduced from its isotopic composition. Thus far, Fe isotopic measurements of presolar silicates are limited to the Fe-54/Fe-56 ratios of 14 grains. Only two slight anomalies (albeit solar within error) were observed. However, these measurements suffered from contamination of Fe from the adjacent meteorite matrix, which diluted any isotopic anomalies. We have isolated four presolar silicates having unusual O isotopic compositions by focused ion beam (FIB) milling and obtained their undiluted Mg and Fe isotopic compositions. These compositions help to identify the grains stellar sources and to determine the source of Fe in the grains.

Mineralogical Studies of a Highly O-17-Depleted and an O-17-Rich Presolar Grain from the Acfer 094 Meteorite

NASA Technical Reports Server (NTRS)

Nguyen, A. N.; Keller, L. P.; Rahman, Z.; Messenger, S.

2012-01-01

Silicate grains are the most abundant condensate around O-rich evolved stars, including red giants, supernovae (SNe) and binary systems. These grains have been identified in abundance in primitive meteorites and interplanetary dust particles [1,2]. Astronomical observations of the silicate spectroscopic features around circumstellar disks indicate that most silicates are amorphous olivine-like grains, though some sources show a large crystalline portion [3]. Fewer astronomical observations of SN and nova silicates exist, but amorphous Mg-rich grains predominate [4,5]. The laboratory analysis of presolar silicates by transmission electron microscopy (TEM) offers more details on the structure and chemistry of individual grains. These studies provide information on the physical and chemical conditions of the parent stellar atmosphere during grain condensation. Moreover, be-cause silicates are susceptible to secondary alteration, processing events succeeding condensation can be traced. Thus far, similar microstructures have been observed for silicates that condensed in SN outflows and in the envelopes of asymptotic giant branch (AGB) stars, but not as many of the comparatively rare SN grains have been analyzed. Here we examine the mineralogies of two presolar silicate grains having different origins.

*Assessing differential transcriptional regulation of IL-8 expression by human airway epithelial cells exposed to diesel exhaust particles

EPA Science Inventory

Background: Exposure to Diesel Exhaust Particles (DEP) induces inflammatory signaling characterized by MAP kinase-mediated activation of NFkB and AP-l in vitro and in bronchial biopsies obtained from human subjects exposed to DEP. NFkB and AP-l activation results in the upregulat...

Comment on "The shape and composition of interstellar silicate grains"

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bradley, J P; Ishii, H

2007-09-27

In the paper entitled 'The shape and composition of interstellar silicate grains' (A & A, 462, 667-676 (2007)), Min et al. explore non-spherical grain shape and composition in modeling the interstellar 10 and 20 {micro}m extinction features. This progression towards more realistic models is vitally important to enabling valid comparisons between dust observations and laboratory measurements. Min et al. proceed to compare their model results with GEMS (glass with embedded metals and sulfides) from IDPs (interplanetary dust particles) and to discuss the nature and origin of GEMS. Specifically, they evaluate the hypothesis of Bradley (1994) that GEMS are interstellar (IS)more » amorphous silicates. From a comparison of the mineralogy, chemical compositions, and infrared (IR) spectral properties of GEMS with their modeling results, Min et al. conclude: 'GEMS are, in general, not unprocessed leftovers from the diffuse ISM'. This conclusion is based, however, on erroneous and incomplete GEMS data. It is important to clarify first that Bradley (1994) never proposed that GEMS are unprocessed leftovers from the diffuse ISM, nor did he suggest that individual subnanogram mass GEMS are a representative sampling of the enormous mass of silicates in the diffuse ISM. Bradley (1994) simply showed that GEMS properties are consistent with those of IS amorphous silicates. It is widely accepted that circumstellar outflows are important sources of IS silicates, and whether GEMS are processed or not, the circumstellar heritage of some has been rigorously confirmed through measurements of non-solar oxygen (O) isotope abundances (Messenger et al., 2003; Floss et al., 2006). Keller et al. (2000) assert that even GEMS without detectable O isotope anomalies are probably also extrasolar IS silicates because they are embedded in carbonaceous material with non-solar D/H isotopic composition. (Much of the silicate dust in the ISM may be isotopically homogenized (Zhukovska et al., 2007)). Recent measurements show that the elemental compositions of GEMS with non-solar isotopic compositions are 'remarkably similar' to those with solar isotopic compositions (Keller & Messenger, 2007). About 80% of all isotopically anomalous IS silicates identified to date are GEMS with detectable and variable O isotopic memories of a circumstellar ancestry (Messenger, 2007). Bradley (1999) proposed that GEMS are IS silicates from 'a presolar interstellar molecular cloud, presumably the local molecular cloud from which the solar system formed'. Although based on incorrect data (detailed below), Min et al. propose that most GEMS actually formed in the presolar molecular cloud, and they further propose that none of them are IS silicates. IS silicate sources include molecular clouds, circumstellar outflows, supernovae, and even recently discovered black hole winds (Molster & Waters; 2003; Jones, 2005; Zhukovska et al. 2007; Markwick-Kemper et al. 2007). The average IS 10 {micro}m extinction feature observed along lines of sight towards the galactic center (modeled by Min et al.) presumably provides a good average for IS silicates, but it cannot distinguish amorphous silicates originating in the presolar molecular cloud from amorphous silicates originating in other interstellar molecular clouds or indeed other sources of amorphous IS silicates. Even if most GEMS accreted in the presolar molecular cloud, then they must also be representatives of some portion of the IS amorphous silicate population. Laboratory heating experiments indicate it is highly unlikely that GEMS were modified in a protoplanetary accretion disk environment (Brownlee et al. 2005). In summary, Min et al. conclude from their modeling of the shape and composition of IS silicates that the properties of GEMS are generally inconsistent with those of IS silicates. First, it has been rigorously confirmed via ion microprobe measurements that some GEMS are indeed presolar IS silicates. Second, regardless of whether GEMS, or components of GEMS, originated in presolar circumstellar outflows or a presolar molecular cloud they are all IS silicates. Third, key GEMS data reported in Min et al. are inaccurate. Had complete isotopic, chemical, mineralogical and infrared (IR) spectral properties of GEMS been considered, Min et al. may have concluded that the properties of GEMS, although not an exact match, are generally consistent with those of amorphous silicates in the ISM.« less

Cooked GEMS - Insights into the Hot Origins of Crystalline Silicates in Circumstellar Disks and the Cold Origins of GEMS

NASA Technical Reports Server (NTRS)

Brownlee, D. E.; Joswiak, D. J.; Bradley, J. P.; Matrajt, G.; Wooden, D. H.

2005-01-01

The comparison of interstellar, circumstellar and primitive solar nebula silicates has led to a significant conundrum in the understanding of the nature of solid materials that begin the planet forming processes. Crystalline silicates are found in circumstellar regions around young stars and also evolved stars ejecting particles into the interstellar medium (ISM) but they are not seen in the interstellar medium itself, the source material for star and planet formation. Crystalline silicates are minor to major components of all known early solar system materials that have been examined as meteorites or interplanetary dust samples. The strong presence of Mg-rich crystalline silicates in Oort cloud comets and their minor presence in some Kuiper belt comets is also indicated by 11.2 m peak in approx. 10 microns "silicate" infrared feature. This evidence strongly indicates that Mg-rich crystalline silicates were abundant components of the solar nebula disk out to at least 10 AU, and present out to 30 AU.

Constraints on cosmic silicates

NASA Astrophysics Data System (ADS)

Ossenkopf, V.; Henning, Th.; Mathis, J. S.

1992-08-01

Observational determinations of opacities of circumstellar silicates, relative to the peak value near 10 microns, are used to estimate the optical constants n and k, the real and imaginary parts of the index of refraction. Circumstellar dust is modified by processing within the interstellar medium. This leads to higher band strengths and a somewhat larger ratio of the opacities at the 18 and 10-micron peaks, compared with circumstellar silicates. By using an effective-medium theory, we calculate the effects of small spherical inclusions of various materials (various oxides, sulfides, carbides, amorphous carbon, and metallic iron) upon silicate opacities. Some of these can increase the absorption coefficient k in the 2-8 micron region appreciably, as is needed to reconcile laboratory silicate opacities with observations of both the interstellar medium and envelopes around late-type stars. We give tables of two sets of optical constants for warm oxygen-deficient and cool oxygen-rich silicates, representative for circumstellar and interstellar silicates. The required opacity in the 2-8 micron region is provided by iron and magnetite.

Battery components employing a silicate binder

DOEpatents

Delnick, Frank M [Albuquerque, NM; Reinhardt, Frederick W [Albuquerque, NM; Odinek, Judy G [Rio Rancho, NM

2011-05-24

A battery component structure employing inorganic-silicate binders. In some embodiments, casting or coating of components may be performed using aqueous slurries of silicates and electrode materials or separator materials.

SOFT X-RAY IRRADIATION OF SILICATES: IMPLICATIONS FOR DUST EVOLUTION IN PROTOPLANETARY DISKS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ciaravella, A.; Cecchi-Pestellini, C.; Jiménez-Escobar, A.

2016-09-01

The processing of energetic photons on bare silicate grains was simulated experimentally on silicate films submitted to soft X-rays of energies up to 1.25 keV. The silicate material was prepared by means of a microwave assisted sol–gel technique. Its chemical composition reflects the Mg{sub 2}SiO{sub 4} stoichiometry with residual impurities due to the synthesis method. The experiments were performed using the spherical grating monochromator beamline at the National Synchrotron Radiation Research Center in Taiwan. We found that soft X-ray irradiation induces structural changes that can be interpreted as an amorphization of the processed silicate material. The present results may havemore » relevant implications in the evolution of silicate materials in X-ray-irradiated protoplanetary disks.« less

Identification of an Extremely 180-Rich Presolar Silicate Grain in Acfer 094

NASA Technical Reports Server (NTRS)

Nguyen, A. N.; Messenger, S.

2009-01-01

Presolar silicate grains have been abundantly identified since their first discovery less than a decade ago [1,2,3]. The O isotopic compositions of both silicate and oxide stardust indicate the vast majority (>90%) condensed around Orich asymptotic giant branch (AGB) stars. Though both presolar phases have average sizes of 300 nm, grains larger than 1 m are extremely uncommon for presolar silicates. Thus, while numerous isotopic systems have been measured in presolar oxide grains [4], very few isotopic analyses for presolar silicates exist outside of O and Si [2,5]. And still, these measurements suffer from isotopic dilution with surrounding matrix material [6]. We conduct a search for presolar silicates in the primitive carbonaceous chondrite Acfer 094 and in some cases obtain high spatial resolution, high precision isotopic ratios.

Geologic Mapping Results for Ceres from NASA's Dawn Mission

NASA Astrophysics Data System (ADS)

Williams, D. A.; Mest, S. C.; Buczkowski, D.; Scully, J. E. C.; Raymond, C. A.; Russell, C. T.

2017-12-01

NASA's Dawn Mission included a geologic mapping campaign during its nominal mission at dwarf planet Ceres, including production of a global geologic map and a series of 15 quadrangle maps to determine the variety of process-related geologic materials and the geologic history of Ceres. Our mapping demonstrates that all major planetary geologic processes (impact cratering, volcanism, tectonism, and gradation (weathering-erosion-deposition)) have occurred on Ceres. Ceres crust, composed of altered and NH3-bearing silicates, carbonates, salts and 30-40% water ice, preserves impact craters and all sizes and degradation states, and may represent the remains of the bottom of an ancient ocean. Volcanism is manifested by cryovolcanic domes, such as Ahuna Mons and Cerealia Facula, and by explosive cryovolcanic plume deposits such as the Vinalia Faculae. Tectonism is represented by several catenae extending from Ceres impact basins Urvara and Yalode, terracing in many larger craters, and many localized fractures around smaller craters. Gradation is manifested in a variety of flow-like features caused by mass wasting (landslides), ground ice flows, as well as impact ejecta lobes and melts. We have constructed a chronostratigraphy and geologic timescale for Ceres that is centered around major impact events. Ceres geologic periods include Pre-Kerwanan, Kerwanan, Yalodean/Urvaran, and Azaccan (the time of rayed craters, similar to the lunar Copernican). The presence of geologically young cryovolcanic deposits on Ceres surface suggests that there could be warm melt pockets within Ceres shallow crust and the dwarf planet remain geologically active.

A review of bioactive silicate ceramics.

PubMed

Wu, Chengtie; Chang, Jiang

2013-06-01

Silicate bioceramics, as a new family of biomaterials, have received significant attention in their application to hard tissue regeneration. Some silicate bioceramics have shown excellent apatite mineralization in simulated body fluids and their ionic products have been shown to enhance the proliferation, osteogenic differentiation and gene expression of stem cells. In this paper, we review the advances in the research of silicate system bioceramics, including preparation methods, mechanical strength, apatite mineralization, dissolution and in vitro and in vivo biological properties. The biological properties and the corresponding mechanism have been highlighted. A look forward to the application of silicate bioceramics to bone regeneration is further suggested.

Diverse subaerial and sublacustrine hot spring settings of the Cerro Negro epithermal system (Jurassic, Deseado Massif), Patagonia, Argentina

NASA Astrophysics Data System (ADS)

Guido, Diego M.; Campbell, Kathleen A.

2012-06-01

The Late Jurassic (~ 150 Ma) Cerro Negro volcanic-epithermal-geothermal system (~ 15 km2 area), Deseado Massif, Patagonia, Argentina, includes two inferred volcanic emission centers characterized by rhyolitic domes linked along NW-SE regional faults that are associated with deeper level Au/Ag mineralization to the NW, and with shallow epithermal quartz veins and mainly travertine surface hot spring manifestations to the SE. Some travertines are silica-replaced, and siliceous and mixed silica-carbonate geothermal deposits also are found. Five hot spring-related facies associations were mapped in detail, which show morphological and textural similarities to Pleistocene-Recent geothermal deposits at Yellowstone National Park (U.S.A.), the Kenya Rift Valley, and elsewhere. They are interpreted to represent subaerial travertine fissure ridge/mound deposits (low-flow spring discharge) and apron terraces (high-flow spring discharge), as well as mixed silica-carbonate lake margin and shallow lake terrace vent-conduit tubes, stromatolitic mounds, and volcano-shaped cones. The nearly 200 mapped fossil vent-associated deposits at Cerro Negro are on a geographical and numerical scale comparable with subaerial and sublacustrine hydrothermal vents at Mammoth Hot Springs, and affiliated with Yellowstone Lake, respectively. Overall, the Cerro Negro geothermal system yields paleoenvironmentally significant textural details of variable quality, owing to both the differential preservation potential of particular subaerial versus subaqueous facies, as well as to the timing and extent of carbonate diagenesis and silica replacement of some deposits. For example, the western fault associated with the Eureka epithermal quartz vein facilitated early silicification of the travertine deposits in the SE volcanic emission center, thereby preserving high-quality, microbial macro- and micro-textures of this silica-replaced "pseudosinter." Cerro Negro provides an opportunity to reconstruct paleogeographic, paleohydrologic and paleoenvironmental associations in a well-exposed, extensive and diverse fossil geothermal system. This Late Jurassic hydrothermal deposit will likely contribute to a better understanding of the impact of depositional and post-depositional history on the development and long-term preservation potential of Lagerstätte in epithermal settings and, more generally, in extreme environments of the geological record.

Geologic Maps and Cross Sections of the Tuba City Open Dump Site and Vicinity, With Implications for the Occurrence and Flow of Ground Water

USGS Publications Warehouse

Otton, James K.; Johnson, Ray H.; Horton, Robert J.

2008-01-01

This report is designed to make available to interested parties geologic and limited hydrologic and geochemical information about the Tuba City Open Dump (TCOD) site. This information has been gathered during studies of the site from January to September 2008. Mapping by the authors and construction of cross sections show that a section of gently northeast-dipping Jurassic sedimentary rocks underlies the TCOD and vicinity. Low mesas in the area are capped by variably cemented gravels and siliceous limestones. Surficial sediments are composed of eolian sand and fluvially reworked eolian sand that overlie bedrock underneath the TCOD. Nearby Pasture Canyon is underlain by fluvial and floodplain sediment consisting of sand and silt. Shallow ground water of the water-table aquifer at the TCOD moves westward through the surficial sediment and the underlying weathered bedrock to Pasture Canyon then southward along the canyon. A fracture zone extends up the wash that passes just to the north of the TCOD and brings deeper ground water of the N-aquifer to the water-table aquifer. Bedrock consists of the Jurassic Navajo Sandstone composed of thick sections of eolian crossbedded sandstone with lesser laterally discontinuous layers of silty sandstone, siltstone, and limestone. Below the Navajo Sandstone is a section informally known as the Kayenta Formation-Navajo Sandstone transition zone. It is composed of calcareous sandstone, silty sandstone, siltstone, and limestone beds that intertongue with crossbedded sandstone. The finer grained rocks in both major bedrock units form aquitards that limit downward movement of ground water. The water-table aquifer is perched on these aquitards, which locally occurs beneath the two open dumps that form the TCOD site. A monocline occupies the position of Pasture Canyon west of the TCOD. Fractures likely related to the monocline are exposed in several localities. Deep ground waters consist of dilute calcium-bicarbonate waters low in all trace elements. Shallow ground water is variably affected by near-surface processes, which add varying amounts of sodium, chloride, sulfate, and trace elements. Locally, human influences, such as the TCOD, affect shallow ground-water chemistry.

Implications of meso- to micro-scale deformation for fault sealing capacity: Insights from the Lenghu5 fold-and-thrust belt, Qaidam Basin, NE Tibetan Plateau

NASA Astrophysics Data System (ADS)

Xie, Liujuan; Pei, Yangwen; Li, Anren; Wu, Kongyou

2018-06-01

As faults can be barriers to or conduits for fluid flow, it is critical to understand fault seal processes and their effects on the sealing capacity of a fault zone. Apart from the stratigraphic juxtaposition between the hanging wall and footwall, the development of fault rocks is of great importance in changing the sealing capacity of a fault zone. Therefore, field-based structural analysis has been employed to identify the meso-scale and micro-scale deformation features and to understand their effects on modifying the porosity of fault rocks. In this study, the Lenghu5 fold-and-thrust belt (northern Qaidam Basin, NE Tibetan Plateau), with well-exposed outcrops, was selected as an example for meso-scale outcrop mapping and SEM (Scanning Electron Microscope) micro-scale structural analysis. The detailed outcrop maps enabled us to link the samples with meso-scale fault architecture. The representative rock samples, collected in both the fault zones and the undeformed hanging walls/footwalls, were studied by SEM micro-structural analysis to identify the deformation features at the micro-scale and evaluate their influences on the fluid flow properties of the fault rocks. Based on the multi-scale structural analyses, the deformation mechanisms accounting for porosity reduction in the fault rocks have been identified, which are clay smearing, phyllosilicate-framework networking and cataclasis. The sealing capacity is highly dependent on the clay content: high concentrations of clay minerals in fault rocks are likely to form continuous clay smears or micro- clay smears between framework silicates, which can significantly decrease the porosity of the fault rocks. However, there is no direct link between the fault rocks and host rocks. Similar stratigraphic juxtapositions can generate fault rocks with very different magnitudes of porosity reduction. The resultant fault rocks can only be predicted only when the fault throw is smaller than the thickness of a faulted bed, in which scenario self-juxtaposition forms between the hanging wall and footwall.

Geologic Map of The Volcanoes Quadrangle, Bernalillo and Sandoval Counties, New Mexico

USGS Publications Warehouse

Thompson, Ren A.; Shroba, Ralph R.; Menges, Christopher M.; Schmidt, Dwight L.; Personius, Stephen F.; Brandt, Theodore R.

2009-01-01

This geologic map, in support of the U.S. Geological Survey Middle Rio Grande Basin Geologic Mapping Project, shows the spatial distribution of surficial deposits, lava flows, and related sediments of the Albuquerque volcanoes, upper Santa Fe Group sediments, faults, and fault-related structural features. These deposits are on, along, and beneath the Llano de Albuquerque (West Mesa) west of Albuquerque, New Mexico. Some of these deposits are in the western part of Petroglyph National Monument. Artificial fill deposits are mapped chiefly beneath and near the City of Albuquerque Soil Amendment Facility and the Double Eagle II Airport. Alluvial deposits were mapped in and along stream channels, beneath terrace surfaces, and on the Llano de Albuquerque and its adjacent hill slopes. Deposits composed of alluvium and colluvium are also mapped on hill slopes. Wedge-shaped deposits composed chiefly of sandy sheetwash deposits, eolian sand, and intercalated calcic soils have formed on the downthrown-sides of faults. Deposits of active and inactive eolian sand and sandy sheetwash deposits mantle the Llano de Albuquerque. Lava flows and related sediments of the Albuquerque volcanoes were mapped near the southeast corner of the map area. They include eleven young lava flow units and, where discernable, associated vent and near-vent pyroclastic deposits associated with cinder cones. Upper Santa Fe Group sediments are chiefly fluvial in origin, and are well exposed near the western boundary of the map area. From youngest to oldest they include a gravel unit, pebbly sand unit, tan sand and mud unit, tan sand unit, tan sand and clay unit, and silty sand unit. Undivided upper Santa Fe Group sediments are mapped in the eastern part of the map area. Faults were identified on the basis of surface expression determined from field mapping and interpretation of aeromagnetic data where concealed beneath surficial deposits. Fault-related structural features are exposed and were mapped near the western boundary of the map area.

Thorium-uranium fission radiography

NASA Technical Reports Server (NTRS)

Haines, E. L.; Weiss, J. R.; Burnett, D. S.; Woolum, D. S.

1976-01-01

Results are described for studies designed to develop routine methods for in-situ measurement of the abundance of Th and U on a microscale in heterogeneous samples, especially rocks, using the secondary high-energy neutron flux developed when the 650 MeV proton beam of an accelerator is stopped in a 42 x 42 cm diam Cu cylinder. Irradiations were performed at three different locations in a rabbit tube in the beam stop area, and thick metal foils of Bi, Th, and natural U as well as polished silicate glasses of known U and Th contents were used as targets and were placed in contact with mica which served as a fission track detector. In many cases both bare and Cd-covered detectors were exposed. The exposed mica samples were etched in 48% HF and the fission tracks counted by conventional transmitted light microscopy. Relative fission cross sections are examined, along with absolute Th track production rates, interaction tracks, and a comparison of measured and calculated fission rates. The practicality of fast neutron radiography revealed by experiments to data is discussed primarily for Th/U measurements, and mixtures of other fissionable nuclei are briefly considered.

Additive Effects on Si3n4 Oxidation/Volatilization in Water Vapor

NASA Technical Reports Server (NTRS)

Opila, Elizabeth J.; Robinson, R. Craig; Fox, Dennis S.; Wenglarz, Richard A.; Ferber, Mattison K.

2002-01-01

Two commercially available additive-containing silicon nitride materials were exposed in four environments which range in severity from dry oxygen at 1 atm pressure, and low gas velocity to an actual turbine engine. Oxidation and volatilization kinetics were monitored at temperatures ranging from 1066 to 1400 C. The main purpose of this paper is to examine the surface oxide morphology resulting from the exposures. It was found that the material surface was enriched in rare earth silicate phases in combustion environments when compared to the oxides formed on materials exposed in dry oxygen. However, the in situ formation of rare earth disilicate phases offered little additional protection from the volatilization of silica observed in combustion environments. It was concluded that externally applied environmental barrier coatings are needed to protect additive-containing silicon nitride materials from volatilization reactions in combustion environments. Introduction Si3N4 is proposed for use as components, such as vanes, in turbine applications. Tens of thousands of hours of life are needed for both land-based turbines and aeropropulsion applications. Additive-containing SisN4 materials are

Cytotoxicity, oxidative stress and expression of adhesion molecules in human umbilical vein endothelial cells exposed to dust from paints with or without nanoparticles.

PubMed

Mikkelsen, Lone; Jensen, Keld A; Koponen, Ismo K; Saber, Anne T; Wallin, Håkan; Loft, Steffen; Vogel, Ulla; Møller, Peter

2013-03-01

Nanoparticles in primary form and nanoproducts might elicit different toxicological responses. We compared paint-related nanoparticles with respect to effects on endothelial oxidative stress, cytotoxicity and cell adhesion molecule expression. Primary human umbilical vein endothelial cells were exposed to primary nanoparticles (fine, photocatalytic or nanosized TiO(2), aluminium silicate, carbon black, nano-silicasol or axilate) and dust from sanding reference- or nanoparticle-containing paints. Most of the samples increased cell surface expressions of vascular cell adhesion molecule-1 (VCAM-1) and intracellular adhesion molecule-1 (ICAM-1), but paint sanding dust samples generally generated less response than primary particles of TiO(2) and carbon black. We found no relationship between the expression of adhesion molecules, cytotoxicity and production of reactive oxygen species. In conclusion, sanding dust from nanoparticle-containing paint did not generate more oxidative stress or expression of cell adhesion molecules than sanding dust from paint without nanoparticles, whereas the primary particles had the largest effect on mass basis.

Pt, Au, Pd and Ru Partitioning Between Mineral and Silicate Melts: The Role of Metal Nanonuggets

NASA Technical Reports Server (NTRS)

Malavergne, V.; Charon, E.; Jones, J.; Agranier, A.; Campbell, A.

2012-01-01

The partition coefficients of Pt and other Pt Group Elements (PGE) between metal and silicate D(sub Metal-Silicate) and also between silicate minerals and silicate melts D(sub Metal-Silicate) are among the most challenging coefficients to obtain precisely. The PGE are highly siderophile elements (HSE) with D(sub Metal-Silicate) >10(exp 3) due to the fact that their concentrations in silicates are very low (ppb to ppt range). Therefore, the analytical difficulty is increased by the possible presence of HSE-rich-nuggets in reduced silicate melts during experiments). These tiny HSE nuggets complicate the interpretation of measured HSE concentrations. If the HSE micro-nuggets are just sample artifacts, then their contributions should be removed before calculations of the final concentration. On the other hand, if they are produced during the quench, then they should be included in the analysis. We still don't understand the mechanism of nugget formation well. Are they formed during the quench by precipitation from precursor species dissolved homogeneously in the melts, or are they precipitated in situ at high temperature due to oversaturation? As these elements are important tracers of early planetary processes such as core formation, it is important to take up this analytical and experimental challenge. In the case of the Earth for example, chondritic relative abundances of the HSE in some mantle xenoliths have led to the concept of the "late veneer" as a source of volatiles (such as water) and siderophiles in the silicate Earth. Silicate crystal/liquid fractionation is responsible for most, if not all, the HSE variation in the martian meteorite suites (SNC) and Pt is the element least affected by these fractionations. Therefore, in terms of reconstructing mantle HSE abundances for Mars, Pt becomes a very important player. In the present study, we have performed high temperature experiments under various redox conditions in order to determine the abundances of Pt, Au, Ru and Pd in minerals (olivine and diopside) and in silicate melts, but also to characterize the sizes, density and chemistry of HSE nuggets when present in the samples.

Quantification of thickness and wrinkling of exfoliated two-dimensional zeolite nanosheets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Prashant; Agrawal, Kumar Varoon; Tsapatsis, Michael

Some two-dimensional (2D) exfoliated zeolites are single- or near single-unit cell thick silicates that can function as molecular sieves. Although they have already found uses as catalysts, adsorbents and membranes precise determination of their thickness and wrinkling is critical as these properties influence their functionality. Here we demonstrate a method to accurately determine the thickness and wrinkles of a 2D zeolite nanosheet by comprehensive 3D mapping of its reciprocal lattice. Since the intensity modulation of a diffraction spot on tilting is a fingerprint of the thickness, and changes in the spot shape are a measure of wrinkling, this mapping ismore » achieved using a large-angle tilt-series of electron diffraction patterns. As a result, application of the method to a 2D zeolite with MFI structure reveals that the exfoliated MFI nanosheet is 1.5 unit cells (3.0 nm) thick and wrinkled anisotropically with up to 0.8 nm average surface roughness.« less

Quantification of thickness and wrinkling of exfoliated two-dimensional zeolite nanosheets

DOE PAGES

Kumar, Prashant; Agrawal, Kumar Varoon; Tsapatsis, Michael; ...

2015-05-11

Some two-dimensional (2D) exfoliated zeolites are single- or near single-unit cell thick silicates that can function as molecular sieves. Although they have already found uses as catalysts, adsorbents and membranes precise determination of their thickness and wrinkling is critical as these properties influence their functionality. Here we demonstrate a method to accurately determine the thickness and wrinkles of a 2D zeolite nanosheet by comprehensive 3D mapping of its reciprocal lattice. Since the intensity modulation of a diffraction spot on tilting is a fingerprint of the thickness, and changes in the spot shape are a measure of wrinkling, this mapping ismore » achieved using a large-angle tilt-series of electron diffraction patterns. As a result, application of the method to a 2D zeolite with MFI structure reveals that the exfoliated MFI nanosheet is 1.5 unit cells (3.0 nm) thick and wrinkled anisotropically with up to 0.8 nm average surface roughness.« less

A global cloud map of the nearest known brown dwarf.

PubMed

Crossfield, I J M; Biller, B; Schlieder, J E; Deacon, N R; Bonnefoy, M; Homeier, D; Allard, F; Buenzli, E; Henning, Th; Brandner, W; Goldman, B; Kopytova, T

2014-01-30

Brown dwarfs--substellar bodies more massive than planets but not massive enough to initiate the sustained hydrogen fusion that powers self-luminous stars--are born hot and slowly cool as they age. As they cool below about 2,300 kelvin, liquid or crystalline particles composed of calcium aluminates, silicates and iron condense into atmospheric 'dust', which disappears at still cooler temperatures (around 1,300 kelvin). Models to explain this dust dispersal include both an abrupt sinking of the entire cloud deck into the deep, unobservable atmosphere and breakup of the cloud into scattered patches (as seen on Jupiter and Saturn). However, hitherto observations of brown dwarfs have been limited to globally integrated measurements, which can reveal surface inhomogeneities but cannot unambiguously resolve surface features. Here we report a two-dimensional map of a brown dwarf's surface that allows identification of large-scale bright and dark features, indicative of patchy clouds. Monitoring suggests that the characteristic timescale for the evolution of global weather patterns is approximately one day.

Experimental evidence for the absence of iron isotope fractionation between metal and silicate liquids at 1 GPa and 1250-1300 °C and its cosmochemical consequences

NASA Astrophysics Data System (ADS)

Hin, Remco C.; Schmidt, Max W.; Bourdon, Bernard

2012-09-01

Iron isotope fractionation during metal-silicate differentiation has been proposed as a cause for differences in iron isotope compositions of chondrites, iron meteorites and the bulk silicate Earth. Stable isotope fractionation, however, rapidly decreases with increasing temperature. We have thus performed liquid metal-liquid silicate equilibration experiments at 1250-1300 °C and 1 GPa to address whether Fe isotope fractionation is resolvable at the lowest possible temperatures for magmatic metal-silicate differentiation. A centrifuging piston cylinder apparatus enabled quantitative metal-silicate segregation. Elemental tin or sulphur was used in the synthetic metal-oxide mixtures to lower the melting temperature of the metal. The analyses demonstrate that eight of the 10 experimental systems equilibrated in a closed isotopic system, as was assessed by varying run durations and starting Fe isotope compositions. Statistically significant iron isotope fractionation between quenched metals and silicates was absent in nine of the 10 experiments and all 10 experiments yield an average metal-silicate fractionation factor of 0.01 ± 0.04‰, independent of whether graphite or silica glass capsules were used. This implies that Fe isotopes do not fractionate during low pressure metal-silicate segregation under magmatic conditions. In large bodies such as the Earth, fractionation between metal and high pressure (>20 GPa) silicate phases may still be a possible process for equilibrium fractionation during metal-silicate differentiation. However, the 0.07 ± 0.02‰ heavier composition of bulk magmatic iron meteorites relative to the average of bulk ordinary/carbonaceous chondrites cannot result from equilibrium Fe isotope fractionation during core segregation. The up to 0.5‰ lighter sulphide than metal fraction in iron meteorites and in one ordinary chondrite can only be explained by fractionation during subsolidus processes.

The effect of melt composition on metal-silicate partitioning of siderophile elements and constraints on core formation in the angrite parent body

NASA Astrophysics Data System (ADS)

Steenstra, E. S.; Sitabi, A. B.; Lin, Y. H.; Rai, N.; Knibbe, J. S.; Berndt, J.; Matveev, S.; van Westrenen, W.

2017-09-01

We present 275 new metal-silicate partition coefficients for P, S, V, Cr, Mn, Co, Ni, Ge, Mo, and W obtained at moderate P (1.5 GPa) and high T (1683-1883 K). We investigate the effect of silicate melt composition using four end member silicate melt compositions. We identify possible silicate melt dependencies of the metal-silicate partitioning of lower valence elements Ni, Ge and V, elements that are usually assumed to remain unaffected by changes in silicate melt composition. Results for the other elements are consistent with the dependence of their metal-silicate partition coefficients on the individual major oxide components of the silicate melt composition suggested by recently reported parameterizations and theoretical considerations. Using multiple linear regression, we parameterize compiled metal-silicate partitioning results including our new data and report revised expressions that predict their metal-silicate partitioning behavior as a function of P-T-X-fO2. We apply these results to constrain the conditions that prevailed during core formation in the angrite parent body (APB). Our results suggest the siderophile element depletions in angrite meteorites are consistent with a CV bulk composition and constrain APB core formation to have occurred at mildly reducing conditions of 1.4 ± 0.5 log units below the iron-wüstite buffer (ΔIW), corresponding to a APB core mass of 18 ± 11%. The core mass range is constrained to 21 ± 8 mass% if light elements (S and/or C) are assumed to reside in the APB core. Incorporation of light elements in the APB core does not yield significantly different redox states for APB core-mantle differentiation. The inferred redox state is in excellent agreement with independent fO2 estimates recorded by pyroxene and olivine in angrites.

Mapping the mineralogy and lithology of Canyonlands, Utah with imaging spectrometer data and the multiple spectral feature mapping algorithm

NASA Technical Reports Server (NTRS)

Clark, Roger N.; Swayze, Gregg A.; Gallagher, Andrea

1992-01-01

The sedimentary sections exposed in the Canyonlands and Arches National Parks region of Utah (generally referred to as 'Canyonlands') consist of sandstones, shales, limestones, and conglomerates. Reflectance spectra of weathered surfaces of rocks from these areas show two components: (1) variations in spectrally detectable mineralogy, and (2) variations in the relative ratios of the absorption bands between minerals. Both types of information can be used together to map each major lithology and the Clark spectral features mapping algorithm is applied to do the job.

Sulfur Saturation Limits in Silicate Melts and their Implications for Core Formation Scenarios for Terrestrial Planets

NASA Technical Reports Server (NTRS)

Holzheid, Astrid; Grove, Timothy L.

2002-01-01

This study explores the controls of temperature, pressure, and silicate melt composition on S solubility in silicate liquids. The solubility of S in FeO-containing silicate melts in equilibrium with metal sulfide increases significantly with increasing temperature but decreases with increasing pressure. The silicate melt structure also exercises a control on S solubility. Increasing the degree of polymerization of the silicate melt structure lowers the S solubility in the silicate liquid. The new set of experimental data is used to expand the model of Mavrogenes and O'Neill(1999) for S solubility in silicate liquids by incorporating the influence of the silicate melt structure. The expected S solubility in the ascending magma is calculated using the expanded model. Because the negative pressure dependence of S solubility is more influential than the positive temperature dependence, decompression and adiabatic ascent of a formerly S-saturated silicate magma will lead to S undersaturation. A primitive magma that is S-saturated in its source region will, therefore, become S-undersaturated as it ascends to shallower depth. In order to precipitate magmatic sulfides, the magma must first cool and undergo fractional crystallization to reach S saturation. The S content in a metallic liquid that is in equilibrium with a magma ocean that contains approx. 200 ppm S (i.e., Earth's bulk mantle S content) ranges from 5.5 to 12 wt% S. This range of S values encompasses the amount of S (9 to 12 wt%) that would be present in the outer core if S is the light element. Thus, the Earth's proto-mantle could be in equilibrium (in terms of the preserved S abundance) with a core-forming metallic phase.

Lattice thermal conductivity of silicate glasses at high pressures

NASA Astrophysics Data System (ADS)

Chang, Y. Y.; Hsieh, W. P.

2016-12-01

Knowledge of the thermodynamic and transport properties of magma holds the key to understanding the thermal evolution and chemical differentiation of Earth. The discovery of the remnant of a deep magma ocean above the core mantle boundary (CMB) from seismic observations suggest that the CMB heat flux would strongly depend on the thermal conductivity, including lattice (klat) and radiative (krad) components, of dense silicate melts and major constituent minerals around the region. Recent measurements on the krad of dense silicate glasses and lower-mantle minerals show that krad of dense silicate glasses could be significantly smaller than krad of the surrounding solid mantle phases, and therefore the dense silicate melts would act as a thermal insulator in deep lower mantle. This conclusion, however, remains uncertain due to the lack of direct measurements on the lattice thermal conductivity of silicate melts under relevant pressure-temperature conditions. Besides the CMB, magmas exist in different circumstances beneath the surface of the Earth. Chemical compositions of silicate melts vary with geological and geodynamic settings of the melts and have strong influences on their thermal properties. In order to have a better view of heat transport within the Earth, it is important to study compositional and pressure dependences of thermal properties of silicate melts. Here we report experimental results on lattice thermal conductivities of silicate glasses with basaltic and rhyolitic compositions up to Earth's lower mantle pressures using time-domain thermoreflectance coupled with diamond-anvil cell techniques. This study not only provides new data for the thermal conductivity of silicate melts in the Earth's deep interior, but is crucial for further understanding of the evolution of Earth's complex internal structure.

Silicate Inclusions in the Kodaikanal IIE Iron Meteorite

NASA Technical Reports Server (NTRS)

Kurat, G.; Varela, M. E.; Zinner, E.

2005-01-01

Silicate inclusions in iron meteorites display an astonishing chemical and mineralogical variety, ranging from chondritic to highly fractionated, silica- and alkali-rich assemblages. In spite of this, their origin is commonly considered to be a simple one: mixing of silicates, fractionated or unfractionated, with metal. The latter had to be liquid in order to accommodate the former in a pore-free way which all models accomplish by assuming shock melting. II-E iron meteorites are particularly interesting because they contain an exotic zoo of silicate inclusions, including some chemically strongly fractionated ones. They also pose a formidable conundrum: young silicates are enclosed by very old metal. This and many other incompatibilities between models and reality forced the formulation of an alternative genetic model for irons. Here we present preliminary findings in our study of Kodaikanal silicate inclusions.

The Abundance and Distribution of Presolar Materials in Cluster IDPS

NASA Technical Reports Server (NTRS)

Messenger, Scott; Keller, Lindsay; Nakamura-Messenger, Keiko; Ito, Motoo

2007-01-01

Presolar grains and remnants of interstellar organic compounds occur in a wide range of primitive solar system materials, including meteorites, interplanetary dust particles (IDPs), and comet Wild-2 samples. Among the most abundant presolar phases are silicate stardust grains and molecular cloud material. However, these materials have also been susceptible to destruction and alteration during parent body and nebular processing. In addition to their importance as direct samples of remote and ancient astrophysical environments, presolar materials thus provide a measure of how well different primitive bodies have preserved the original solar system starting materials. The matrix normalized abundances of presolar silicate grains in meteorites range from 20 ppm in Semarkona and Bishunpur to 170 ppm for Acfer 094. The lower abundances of presolar silicates in Bishunpur and Semarkona has been ascribed to the destruction of presolar silicates during aqueous processes. Presolar silicates appear to be significantly more abundant in anhydrous IDPs, possibly because these materials did not experience parent body hydrothermal alteration. Among IDPs the estimated abundances of presolar silicates vary by more than an order of magnitude, from 480 to 5500 ppm. The wide disparity in the abundances of presolar silicates of IDPs may be a consequence of the relatively small total area analyzed in those studies and the fine grain sizes of the IDPs. Alternatively, there may be a wide range in presolar silicate abundances between different IDPs. This view is supported by the observation that 15N-rich IDPs have higher presolar silicate abundances than those with isotopically normal N.

Crystal Structure and Chemical Composition of a Presolar Silicate from the Queen Elizabeth Range 99177 Meteorite

NASA Technical Reports Server (NTRS)

Nguyen, A. N.; Keller, L. P.; Rahman, Z.; Messenger, S.

2013-01-01

Mineral characterization of presolar silicate grains, the most abundant stardust phase, has provided valuable information about the formation conditions in circumstellar environments and in super-nova (SN) outflows. Spectroscopic observations of dust around evolved stars suggest a majority of amor-phous, Mg-rich olivine grains, but crystalline silicates, most of which are pyroxene, have also been observed [1]. The chemical compositions of hundreds of presolar silicates have been determined by Auger spectroscopy and reveal high Fe contents and nonstoichiometric compositions intermediate to olivine and pyroxene [2-6]. The unexpectedly high Fe contents can partly be attributed to secondary alteration on the meteorite parent bodies, as some grains have Fe isotopic anomalies from their parent stellar source [7]. Only about 35 presolar silicates have been studied for their mineral structures and chemical compositions by transmission electron microscopy (TEM). These grains display a wide range of compositions and structures, including crystalline forsterite, crystalline pyroxene, nanocrystalline grains, and a majority of amorphous nonstoichiometric grains. Most of these grains were identified in the primitive Acfer 094 meteorite. Presolar silicates from this meteorite show a wide range of Fe-contents, suggestive of secondary processing on the meteorite parent body. The CR chondrite QUE 99177 has not suffered as much alteration [8] and displays the highest presolar silicate abundance to date among carbonaceous chondrites [3, 6]. However, no mineralogical studies of presolar silicates from this meteorite have been performed. Here we examine the mineralogy of a presolar silicate from QUE 99177.

Textbook Treatments of Electrostatic Potential Maps in General and Organic Chemistry

ERIC Educational Resources Information Center

Hinze, Scott R.; Williamson, Vickie M.; Deslongchamps, Ghislain; Shultz, Mary Jane; Williamson, Kenneth C.; Rapp, David N.

2013-01-01

Electrostatic potential maps (EPMs) allow for representation of key molecular-level information in a relatively simple and inexpensive format. As these visualizations become more prevalent in instruction, it is important to determine how students are exposed to them and supported in their use. A systematic review of current general and organic…

Antigenicity of recombinant maltose binding protein-Mycobacterium avium subsp. paratuberculosis fusion proteins with and without factor Xa cleaving

USDA-ARS?s Scientific Manuscript database

Mycobacterium avium subsp paratuberculosis (MAP) causes Johne’s disease (JD) in ruminants. Proteomic studies have shown that MAP expresses certain proteins when exposed to in vitro physiological stress conditions similar to the conditions experienced within a host during natural infection. Such prot...

Dynamic laser-induced effects in nanocomposite systems based on the cadmium sulfide quantum dots in a silicate matrix.

PubMed

Voznesenskiy, S S; Sergeev, A A; Postnova, I V; Galkina, A N; Shchipunov, Yu A; Kulchin, Yu N

2015-02-23

In this paper we study the laser-induced modification of optical properties of nanocomposite based on cadmium sulphide quantum dots encapsulated into thiomalic acid shell which were embedded into a porous silica matrix. It was found that exposure to laser radiation at λ = 405.9 nm leads to modification of optical properties of nanocomposite. For this exposed area there is a significant amount of photodynamic changes under subsequent exposure to laser radiation at λ = 405.9 nm, namely photoabsorption and photorefraction which were studied at λ = 633 nm. The value of these effects dependent on the concentration of quantum dots and modifying radiation parameters. Moreover, it has dependence from polarization of exposure radiation.

Granulites from Northwest Indian Shield: Their differences and similarities with Southern Indian granulite terrain

NASA Technical Reports Server (NTRS)

Sharma, R. S.

1988-01-01

Granulite facies suite in the NW Indian Shield is exposed at Sand Mata, Udaipur district, Rajasthan, as an oval-shaped massif within amphibolite facies rocks of the Banded Gneissic Complex (3.5 to 2.6 b.y. old) - a possible analogue of the Peninsular gneiss of Dharwar craton. On the basis of quantitative P-T estimates, combined with the textural evidence for the crystallization sequence of the Al-silicate polymorphs (kyanite to sillimanite to kyanite) in the pelitic granulite, the deduced P-T path for the Sand Mata granulites is the reverse of that characterizing the Plate tectonic collision zone. It, however, agrees with the P-T path inferred in the case of the southern Indian granulitic rocks.

Mid-tertiary ash flow tuff cauldrons, southwestern New Mexico

NASA Technical Reports Server (NTRS)

Elston, W. E.

1984-01-01

Characteristics of 28 known or suspected mid-Tertiary ash-flow tuff cauldrons in New Mexico are described. The largest region is 40 km in diameter, and erosional and block faulting processes have exposed levels as far down as the plutonic roots. The study supports a five-stage process: precursor, caldera collapse, early post-collapse, volcanism, major ring-fracture volcanism, and hydrothermal activity. The stages can repeat or the process can stop at any stage. Post-collapse lavas fell into two categories: cauldron lavas, derived from shallow defluidized residues of caldera-forming ash flow tuff eruption, and framework lavas, evolved from a siliceous pluton below the cauldron complex. The youngest caldera was shallow and formed from asymmetric subsidence and collapse of the caldera walls.

Journey to a metal world: Concept for a Discovery mission to Psyche

NASA Astrophysics Data System (ADS)

Wenkert, D.; Elkins-Tanton, L. T.; Asphaug, E. I.; Bairstow, S.; Bell, J. F.; Bercovici, D. A.; Bills, B. G.; Binzel, R. P.; Bottke, W. F.; Jun, I.; Landau, D.; Marchi, S.; Oh, D.; Weiss, B. P.; Zuber, M. T.

2013-12-01

Psyche is one of the most singular asteroids in the main belt. It is thought to be the core of a Vesta-sized planetesimal, exposed through collisions. Based on spectra, radar surface properties, and bulk density estimates, it appears to be a world not of ice or silicate rock, but of iron. By understanding its nature, we can glean insights into the differentiation of planetesimals, the growth of planets, the composition and structure of a planetary core, and the geology of a metallic body. For all of these reasons, and its relative accessibility to low cost rendezvous and orbit, Psyche is a superb target for a Discovery-class mission that would measure its geology and geomorphology, shape, composition, magnetic field, and mass distribution.

Preliminary lithogeochemical map showing near-surface rock types in the Chesapeake Bay watershed, Virginia and Maryland

USGS Publications Warehouse

Peper, John D.; McCartan, Lucy; Horton, J. Wright; Reddy, James E.

2001-01-01

This preliminary experimental lithogeochemical map shows the distribution of rock types in the Virginia and Maryland parts of the Chesapeake Bay watershed. The map was produced digitally by classifying geologic-map units according to composition, mineralogy, and texture; rather than by age and stratigraphic relationships as shown on traditional geologic maps. This map differs from most lithologic maps in that the lithogeochemical unit classification distinguishes those rock units having key water-reactive minerals that may induce acid neutralization, or reduction, of hosted water at the weathering interface. The validity of these rock units, however, is independent of water chemistry, because the rock units are derived from geologic maps and rock descriptions. Areas of high soil carbon content, and sulfide metal deposits are also shown. Water-reactive minerals and their weathering reactions yield five lithogeochemical unit classes: 1) carbonate rock and calcareous rocks and sediments, the most acid-neutralizing; 2)carbonaceous-sulfidic rocks and sediments, oxygen-depleting and reducing; 3) quartzofeldspathic rocks and siliciclastic sediments, relatively weakly reactive with water; 4) mafic silicate rocks/sediments, oxygen consuming and high solute-load delivering; and, 5) the rarer calcareous-sulfidic (carbonaceous) rocks, neutralizing and reducing. Earlier studies in some parts of the map area have related solute loads in ground and stream waters to some aspects of bedrock lithology. More recent preliminary tests of relationships between four of the classes of mapped lithogeochemical units and ground water chemistry, in the Mid-Atlantic area using this map, have focused on and verified the nitrate-reducing and acid-neutralizing properties of some bedrock and unconsolidated aquifer rock types. Sulfide mineral deposits and their mine-tailings effects on waters are beginning to be studied by others. Additional testing of relationships among the lithogeochemical units and aspects of ground and surface water chemistry could help to refine the lithogeochemical classification, and this map. The testing could also improve the usefulness of the map for assessing aquifer reactivity and the transport properties of reactive contaminants such as acid rain, and nitrate from agricultural sources, in the Chesapeake Bay watershed.

Partial Melting of the Indarch (EH4) Meteorite : A Textural, Chemical and Phase Relations View of Melting and Melt Migration

NASA Technical Reports Server (NTRS)

McCoy, Timothy J.; Dickinson, Tamara L.; Lofgren, Gary E.

2000-01-01

To Test whether Aubrites can be formed by melting of enstatite Chondrites and to understand igneous processes at very low oxygen fugacities, we have conducted partial melting experiments on the Indarch (EH4) chondrite at 1000-1500 C. Silicate melting begins at 1000 C. Substantial melt migration occurs at 1300-1400 C and metal migrates out of the silicate change at 1450 C and approx. 50% silicate partial melting. As a group, our experiments contain three immiscible metallic melts 9Si-, and C-rich), two immiscible sulfide melts(Fe-and FeMgMnCa-rich) and Silicate melt. Our partial melting experiments on the Indarch (EH4) enstatite Chondrite suggest that igneous processes at low fO2 exhibit serveral unique features. The complete melting of sulfides at 1000 C suggest that aubritic sulfides are not relicts. Aubritic oldhamite may have crystallized from Ca and S complexed in the silicate melt. Significant metal-sulfide melt migration might occur at relatively low degrees of silicate partial melting. Substantial elemental exchange occurred between different melts (e.g., between sulfide and silicate, Si between silicate and metal), a feature not observed during experiments at higher fO2. This exchange may help explain the formation of aubrites from known enstatite chondrites.

A design of spectrophotometric microfluidic chip sensor for analyzing silicate in seawater

NASA Astrophysics Data System (ADS)

Cao, X.; Zhang, S. W.; Chu, D. Z.; Wu, N.; Ma, H. K.; Liu, Y.

2017-08-01

High quality and continuous in situ silicate data are required to investigate the mechanism of the biogeochemical cycles and the formation of red tide. There is an urgently growing need for autonomous in situ silicate instruments that perform determination on various platforms. However, due to the high reagents and power consumption, as well as high system complexity leading to low reliability and robustness, the performance of the commercially available silicate sensors is not satisfactory. With these problems, here we present a new generation of microfluidic continuous flow analysis silicate sensor with sufficient analytical performance and robustness, for in situ determination of soluble silicate in seawater. The reaction mechanism of this sensor is based on the reaction of silicate with ammonium molybdate to form a yellow silicomolybdate complex and further reduction to silicomoIybdenum blue by ascorbic acid. The minimum limit of detection was 45.1 nmol L-1, and the linear determination range of the sensor is 0-400 μmol L-1. The recovery rate of the actual water is between 98.1%-104.0%, and the analyzing cycle of the sensor is about 5 minutes. This sensor has the advantages of high accuracy, high integration, low water consumption, and strong anti-interference ability. It has been successfully applied to measuring the silicate in seawater in Jiaozhou Bay.

Mode of action studies on the formation of enamel minerals from a novel toothpaste containing calcium silicate and sodium phosphate salts.

PubMed

Sun, Yuekui; Li, Xiaoke; Deng, Yan; Sun, Jianing N; Tao, DanYing; Chen, Hui; Hu, Qinghong; Liu, Renjiang; Liu, Weining; Feng, Xiping; Wang, Jinfang; Carvell, Mel; Joiner, Andrew

2014-06-01

To investigate in vitro and in situ the deposition and formation of hydroxyapatite (HAP) on enamel surfaces following brushing with a novel toothpaste containing calcium silicate (CaSi), sodium phosphate salts and fluoride. Polished enamel blocks were brushed in vitro with a slurry of the CaSi toothpaste. After one brush and four weeks simulated brushing the enamel surfaces were analysed. In an in situ protocol, enamel blocks were attached to first or second molar teeth of healthy subjects, exposed to 4 weeks twice per day brushing with the CaSi toothpaste and then analysed. The surface deposits were analysed using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM) and selected area electron diffraction (SAED). In addition, the CaSi toothpaste was slurried in simulated oral fluid (SOF) over a 3 hour period and the solids were isolated and analysed by Fourier transform infrared spectroscopy (FTIR). The FTIR study demonstrated that calcium phosphate phases had formed and these became increasingly crystalline over 3 hours. CaSi was deposited onto enamel surfaces following one brushing with the toothpaste in vitro.The deposited particles showed evidence of HAP crystalline phases associated with the CaSi. Following 4 weeks brushing in vitro, the deposition increased and analyses showed that the deposited material was HAP. These results were confirmed by the in situ study. Calcium silicate can be deposited onto enamel surfaces from a novel toothpaste formulation where it can form the enamel mineral HAP. A novel toothpaste formulation containing CaSi can form HAP on enamel surfaces. The potential of this technology is for a novel approach to the repair of demineralised enamel and the protection of enamel during acid exposure. © 2014 Elsevier Ltd. All rights reserved.

Space Weathering Products Found on the Surfaces of the Itokawa Dust Particles: A Summary of the Initial Analysis

NASA Technical Reports Server (NTRS)

Noguchi, T.; Kimura, M.; Hashimoto, T.; Konno, M.; Nakamura, T.; Ogami, T.; Ishida, H.; Sagae, R.; Tsujimoto, S.; Tsuchiyama, A,;

Experimental Investigation of Space Radiation Processing in Lunar Soil Ilmenite: Combining Perspectives from Surface Science and Transmission Electron Microscopy

NASA Technical Reports Server (NTRS)

Christoffersen, R.; Keller, L. P.; Rahman, Z.; Baragiola, R.

2010-01-01

Energetic ions mostly from the solar wind play a major role in lunar space weathering because they contribute structural and chemical changes to the space-exposed surfaces of lunar regolith grains. In mature mare soils, ilmenite (FeTiO3) grains in the finest size fraction have been shown in transmission electron microscope (TEM) studies to exhibit key differences in their response to space radiation processing relative to silicates [1,2,3]. In ilmenite, solar ion radiation alters host grain outer margins to produce 10-100 nm thick layers that are microstructurally complex, but dominantly crystalline compared to the amorphous radiation-processed rims on silicates [1,2,3]. Spatially well-resolved analytical TEM measurements also show nm-scale compositional and chemical state changes in these layers [1,3]. These include shifts in Fe/Ti ratio from strong surface Fe-enrichment (Fe/Ti >> 1), to Fe depletion (Fe/Ti < 1) at 40-50 nm below the grain surface [1,3]. These compositional changes are not observed in the radiation-processed rims on silicates [4]. Several mechanism(s) to explain the overall relations in the ilmenite grain rims by radiation processing and/or additional space weathering processes were proposed by [1], and remain under current consideration [3]. A key issue has concerned the ability of ion radiation processing alone to produce some of the deeper- penetrating compositional changes. In order to provide some experimental constraints on these questions, we have performed a combined X-ray photoelectron spectroscopy (XPS) and field-emission scanning transmission electron (FE-STEM) study of experimentally ion-irradiated ilmenite. A key feature of this work is the combination of analytical techniques sensitive to changes in the irradiated samples at depth scales going from the immediate surface (approx.5 nm; XPS), to deeper in the grain interior (5-100 nm; FE-STEM).

Effect of silicate ions on electrode overvoltage

NASA Technical Reports Server (NTRS)

Gras, J. M.; Seite, C.

1979-01-01

The influence of the addition of a silicate to a caustic solution (KOH) is studied in order to determine the degree to which silicates inhibit the corrosion of chrysotile under conditions of electrolysis at working temperatures of 100 C and above. In an alkaline solution containing various silicate concentrations, current density was increased and electrode overvoltage was measured. Results show that silicate ion concentrations in the electrolyte increase with temperature without effecting electrochemical performance up to 115 C at 700 MA/sqcm. At this point the concentration is about 0.5 g Si/100 g KOH. Beyond this limit, electrolytic performance rapidly degenerates due to severe oxidation of the electrodes.

Laboratory simulation of infrared astrophysical features. Ph.D. Thesis; [emission spectra of comets

NASA Technical Reports Server (NTRS)

Rose, L. A.

1977-01-01

Intermediate resolution emission spectroscopy was used to study a group of 9 terrestrial silicates, 1 synthetic silicate, 6 meteorites and 2 lunar soils; comparisons were made with the intermediate resolution spectra of Comet Kohoutek in order to determine which materials best simulate the 10um astrophysical feature. Mixtures of silicates which would yield spectra matching the spectrum of the comet in the 10um region include: (1) A hydrous layer lattice silicate in combination with a high temperature condensate; (2) an amorphous magnesium silicate in combination with a high temperature condensate and (3) glassy olivine and glassy anorthite in approximately equal proportions.

Nature of very small grains - PAH molecules or silicates?. [Polycyclic Aromatic Hydrocarbon in interstellar dust

NASA Technical Reports Server (NTRS)

Desert, F. X.; Leger, A.; Puget, J. L.; Boulanger, F.; Sellgren, K.

1986-01-01

The predictions of the model of Puget et al. (1985) for the emission from Very Small Grains (VSGs) including both graphitic and silicate components are compared with published 8-13-micron observations of astronomical sources. The VSGs are found to be mainly graphitic and an upper limit is placed on the relative mass of silicates based on lack of the 9.7-micron silicate emission feature on M 82 and NGC 2023. This dissymetry in the composition of VSGs supports the suggestion that they are formed in grain-grain collisions where the behaviors of graphite and silicate grains are expected to be quite different.

Lithologic mapping in the Mountain Pass, California area using Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) data

USGS Publications Warehouse

Rowan, L.C.; Mars, J.C.

2003-01-01

Evaluation of an Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) image of the Mountain Pass, California area indicates that several important lithologic groups can be mapped in areas with good exposure by using spectral-matching techniques. The three visible and six near-infrared bands, which have 15-m and 30-m resolution, respectively, were calibrated by using in situ measurements of spectral reflectance. Calcitic rocks were distinguished from dolomitic rocks by using matched-filter processing in which image spectra were used as references for selected spectral categories. Skarn deposits and associated bright coarse marble were mapped in contact metamorphic zones related to intrusion of Mesozoic and Tertiary granodioritic rocks. Fe-muscovite, which is common in these intrusive rocks, was distinguished from Al-muscovite present in granitic gneisses and Mesozoic granite. Quartzose rocks were readily discriminated, and carbonate rocks were mapped as a single broad unit through analysis of the 90-m resolution, five-band surface emissivity data, which is produced as a standard product at the EROS Data Center. Three additional classes resulting from spectral-angle mapper processing ranged from (1) a broad granitic rock class (2) to predominately granodioritic rocks and (3) a more mafic class consisting mainly of mafic gneiss, amphibolite and variable mixtures of carbonate rocks and silicate rocks. ?? 2002 Elsevier Science Inc. All rights reserved.

Ultra-high sensitivity moment magnetometry of geological samples using magnetic microscopy

NASA Astrophysics Data System (ADS)

Lima, Eduardo A.; Weiss, Benjamin P.

2016-09-01

Useful paleomagnetic information is expected to be recorded by samples with moments up to three orders of magnitude below the detection limit of standard superconducting rock magnetometers. Such samples are now detectable using recently developed magnetic microscopes, which map the magnetic fields above room-temperature samples with unprecedented spatial resolutions and field sensitivities. However, realizing this potential requires the development of techniques for retrieving sample moments from magnetic microscopy data. With this goal, we developed a technique for uniquely obtaining the net magnetic moment of geological samples from magnetic microscopy maps of unresolved or nearly unresolved magnetization. This technique is particularly powerful for analyzing small, weakly magnetized samples such as meteoritic chondrules and terrestrial silicate crystals like zircons. We validated this technique by applying it to field maps generated from synthetic sources and also to field maps measured using a superconducting quantum interference device (SQUID) microscope above geological samples with moments down to 10-15 Am2. For the most magnetic rock samples, the net moments estimated from the SQUID microscope data are within error of independent moment measurements acquired using lower sensitivity standard rock magnetometers. In addition to its superior moment sensitivity, SQUID microscope net moment magnetometry also enables the identification and isolation of magnetic contamination and background sources, which is critical for improving accuracy in paleomagnetic studies of weakly magnetic samples.

Tree growth prediction using size and exposed crown area

Treesearch

Peter H. Wyckoff; James S. Clark

2005-01-01

We address the relationships between tree growth rate and growing environment for 21 co-occurring species. Tree growth rates are obtained from mapped plots at the Coweeta Long-Term Ecological Research site in the southern Appalachian Mountains. We employ high-resolution aerial photography to assess the light environment for trees growing in these plots, using exposed...

Microfabrics in Siliceous Hotsprings: Yellowstone National Park, Wyoming

NASA Technical Reports Server (NTRS)

Guidry, S. A.; Chafetz, H. S.; Westall, F.

2001-01-01

Microfabrics shed light on the mechanisms governing siliceous sinter precipitation, the profound effects of microorganisms, as well as a conventional facies model for siliceous hotsprings. Additional information is contained in the original extended abstract.

On the Relation of Silicates and SiO Maser in Evolved Stars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Jiaming; Jiang, Biwei, E-mail: bjiang@bnu.edu.cn

2017-04-01

The SiO molecule is one of the candidates for the seed of silicate dust in the circumstellar envelope of evolved stars, but this opinion is challenged. In this work we investigate the relation of the SiO maser emission power and the silicate dust emission power. With both our own observation by using the PMO/Delingha 13.7 m telescope and archive data, a sample is assembled of 21 SiO v  = 1, J  = 2 − 1 sources and 28 SiO v  = 1, J  = 1 − 0 sources that exhibit silicate emission features in the ISO /SWS spectrum as well. The analysis of their SiO maser and silicatemore » emission power indicates a clear correlation, which is not against the hypothesis that the SiO molecules are the seed nuclei of silicate dust. On the other hand, no correlation is found between SiO maser and silicate crystallinity, which may imply that silicate crystallinity does not correlate with mass-loss rate.« less

AC electrical breakdown phenomena of epoxy/layered silicate nanocomposite in needle-plate electrodes.

PubMed

Park, Jae-Jun; Lee, Jae-Young

2013-05-01

Epoxy/layered silicate nanocomposite for the insulation of heavy electric equipments were prepared by dispersing 1 wt% of a layered silicate into an epoxy matrix with a homogenizing mixer and then AC electrical treeing and breakdown tests were carried out. Wide-angle X-ray diffraction (WAXD) analysis and transmission electron microscopy (TEM) observation showed that nano-sized monolayers were exfoliated from a multilayered silicate in the epoxy matrix. When the nano-sized silicate layers were incorporated into the epoxy matrix, the breakdown rate in needle-plate electrode geometry was 10.6 times lowered than that of the neat epoxy resin under the applied electrical field of 520.9 kV/mm at 30 degrees C, and electrical tree propagated with much more branches in the epoxy/layered silicate nanocomposite. These results showed that well-dispersed nano-sized silicate layers retarded the electrical tree growth rate. The effects of applied voltage and ambient temperature on the tree initiation, growth, and breakdown rate were also studied, and it was found that the breakdown rate was largely increased, as the applied voltage and ambient temperature increased.

Mapping Relative Likelihood for the Presence of Naturally Occurring Asbestos in Placer and Eastern Sacramento Counties, California

NASA Astrophysics Data System (ADS)

Higgins, C. T.; Clinkenbeard, J. P.; Churchill, R. K.

2006-12-01

Naturally occurring asbestos (NOA) is a term applied to the geologic occurrence of six types of silicate minerals that have asbestiform habit. These include the serpentine mineral chrysotile and the amphibole minerals actinolite, amosite, anthophyllite, crocidolite, and tremolite; all are classified as known human carcinogens. NOA, which is likely to be present in at least 50 of the 58 counties of California, is most commonly associated with serpentinite, but has been identified in other geologic settings as well. Because of health concerns, knowledge of where NOA may be present is important to regulatory agencies and the public. To improve this knowledge, the California Geological Survey (CGS) has prepared NOA maps of Placer County and eastern Sacramento County; both counties contain geologic settings where NOA has been observed. The maps are based primarily on geologic information compiled and interpreted from existing geologic and soils maps and on limited fieldwork. The system of map units is modified from an earlier one developed by the CGS for an NOA map of nearby western El Dorado County. In the current system, the counties are subdivided into different areas based on relative likelihood for the presence of NOA. Three types of areas are defined as most likely, moderately likely, and least likely to contain NOA. A fourth type is defined as areas of faulting and shearing; these geologic structures may locally increase the likelihood for the presence of NOA within or adjacent to areas most likely or moderately likely to contain NOA. The maps do not indicate if NOA is present or absent in bedrock or soils at any particular location. Local air pollution control districts are using the maps to help determine where to minimize generation of and exposure to dust that may contain NOA. The maps and accompanying reports can be viewed at http://www.consrv.ca.gov/cgs/ under Hazardous Minerals.

40 CFR 721.10018 - Calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Calcium hydroxide oxide silicate (Ca6... New Uses for Specific Chemical Substances § 721.10018 Calcium hydroxide oxide silicate (Ca6(OH)2O2... substance identified as calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3) (PMN P-01-442; CAS No. 13169...

40 CFR 721.10018 - Calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Calcium hydroxide oxide silicate (Ca6... New Uses for Specific Chemical Substances § 721.10018 Calcium hydroxide oxide silicate (Ca6(OH)2O2... substance identified as calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3) (PMN P-01-442; CAS No. 13169...

40 CFR 721.10018 - Calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Calcium hydroxide oxide silicate (Ca6... New Uses for Specific Chemical Substances § 721.10018 Calcium hydroxide oxide silicate (Ca6(OH)2O2... substance identified as calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3) (PMN P-01-442; CAS No. 13169...

40 CFR 721.10018 - Calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Calcium hydroxide oxide silicate (Ca6... New Uses for Specific Chemical Substances § 721.10018 Calcium hydroxide oxide silicate (Ca6(OH)2O2... substance identified as calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3) (PMN P-01-442; CAS No. 13169...

40 CFR 721.10018 - Calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Calcium hydroxide oxide silicate (Ca6... New Uses for Specific Chemical Substances § 721.10018 Calcium hydroxide oxide silicate (Ca6(OH)2O2... substance identified as calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3) (PMN P-01-442; CAS No. 13169...

Polysilicate binding for silicate paints

NASA Astrophysics Data System (ADS)

Ivanovna, Loganina Valentina; Nikolaevna, Kislitsyna Svetlana; Bisengalievich, Mazhitov Yerkebulan

2018-06-01

It was suggested, that the polysilicate solutions obtained by mixing liquid glass and silicic acid sol as a binder in the manufacture of silicate paints. Information is provided on the structure and a property of the sodium polysilicate binder is presented. It has been found that the addition of silica powder to a liquid glass causes gelling in the course of time. It has been established that the introduction of the sol (increasing the silicate module) contributes to an increase in the fraction of high-polymer fractions of silicic anion, with the increase in the sol content of the polymer form of silica increasing. The research results the structure of sols and polysilicate solutions by the method of violation of total internal reflection. By the method of IR spectroscopy, the molybdate method established the presence of silica in the polysilicate binder polymeric varieties, which provides an increase in the stability of silicate coatings.

THE METABOLISM OF SILICON IN THE RAT AND ITS RELATION TO THE FORMATION OF ARTIFICIAL SILICEOUS CALCULI

PubMed Central

Keeler, Richard F.; Lovelace, Stuart A.

1959-01-01

The urinary excretion of silicon in the rat was found to be enhanced beyond normal levels by the administration of various chemical forms of silicon. The excretion was enhanced to a much greater degree by the administration of ethyl silicate than by magnesium trisilicate, sodium metasilicate, or water glass. The tolerance level of rats to sustained daily doses of ethyl silicate fed via stomach tube was approximately 15 to 30 mg. of silicon per rat per day. Urinary silicon excretion was found to be a straight line function of the concentration of ethyl silicate administered, via stomach tube, with approximately 18 per cent of the administered silicon appearing in the urine at all levels tested. Using sustained dietary additions of ethyl silicate as a means of enhancing urine silicon levels, artificial siliceous urinary calculi were consistently produced on zinc pellets implanted in the bladders of rats. PMID:13654631

Search for Large Presolar Silicate Grains in the QUE 99177 CR Chondrite

NASA Technical Reports Server (NTRS)

Nguyen, A. N.; Messenger, S.

2012-01-01

Silicates are among the most abundant pre-solar grain type, and their diverse chemical and isotopic compos-tions preserve detailed constraints on their stellar origins, condensation conditions, and nucleosynthetic and interstellar processes. Yet, owing to their small sizes, relatively few grains have been measured for isotopic compositions besides O and Si, and their mineralogy is poorly characterized. The average grain size (approx 270 nm) limits the number of analyses that can be conducted on a given grain, and their identification among solar system silicates introduces contaminating signal. These difficulties can be overcome by identifying large presolar silicate grains. However, such grains are very rare and only two approx 1 micron grains have been discovered. We are conducting a dedicated search for large presolar silicates in size-separated QUE 99177 matrix material. This primitive meteorite has among the highest abundance of presolar silicates

Layer-by-Layer Templated Assembly of Silica at the Nanoscale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hinestrosa, Juan Pablo; Sutton, Jonathan E.; Allison, David P.

2013-01-29

Bioinspired bottom-up assembly and layer-by-layer (LbL) construction of inorganic materials from lithographically defined organic templates enables the fabrication of nanostructured systems under mild temperature and pH conditions. Such processes open the door to low-impact manufacturing and facile recycling of hybrid materials for energy, biology, and information technologies. Here, templated LbL assembly of silica was achieved using a combination of electron beam lithography, chemical lift-off, and aqueous solution chemistry. Nanopatterns of lines, honeycomb-lattices, and dot arrays were defined in polymer resist using electron beam lithography. Following development, exposed areas of silicon were functionalized with a vapor deposited amine-silane monolayer. Silicic acidmore » solutions of varying pH and salt content were reacted with the patterned organic amine-functional templates. Vapor treatment and solution reaction could be repeated, allowing LbL deposition. Conditions for the silicic acid deposition had a strong effect on thickness of each layer, and the morphology of the amorphous silica formed. Defects in the arrays of silica nanostructures were minor and do not affect the overall organization of the layers. In conclusion, the bioinspired method described here facilitates the bottom-up assembly of inorganic nanostructures defined in three dimensions and provides a path, via LbL processing, for the construction of layered hybrid materials under mild conditions.« less

Surficial geologic map of the greater Omaha area, Nebraska and Iowa

USGS Publications Warehouse

Shroba, R.R.; Brandt, T.R.; Blossom, J.C.

2001-01-01

Geologic mapping, in support of the USGS Omaha-Kansas City Geologic Mapping Project, shows the spatial distribution of artificial-fill, alluvial, eolian, and glacial deposits and bedrock in and near Omaha, Nebraska. Artificial fill deposits are mapped chiefly beneath commercial structures, segments of interstate highways and other major highways, railroad tracks, airport runways, and military facilities, and in landfills and earth fills. Alluvial deposits are mapped beneath flood plains, in stream terraces, and on hill slopes. They include flood-plain and stream-channel alluvium, sheetwash alluvium, and undivided sheetwash alluvium and stream alluvium. Wind-deposited loess forms sheets that mantle inter-stream areas and late Wisconsin terrace alluvium. Peoria Loess is younger of the two loess sheets and covers much of the inter-stream area in the map area. Loveland Loess is older and is exposed in a few small areas in the eastern part of the map area. Glacial deposits are chiefly heterogeneous, ice-deposited, clayey material (till) and minor interstratified stream-deposited sand and gravel. Except for small outcrops, glacial deposits are covered by eolian and alluvial deposits throughout most of the map area. Bedrock is locally exposed in natural exposures along the major streams and in quarries. It consists of Dakota Sandstone and chiefly limestone and shale of the Lansing and Kansas City Groups. Sand and gravel in flood plain and stream-channel alluvium in the Platte River valley are used mainly for concrete aggregate. Limestone of the Lansing and Kansas City Groups is used for road-surfacing material, rip rap, and fill material.

Surface-structural Control on Minor Element Zoning and Growth Mechanism in Synthetic Magmatic Clinopyroxene

NASA Astrophysics Data System (ADS)

Paquette, J.; Deakin, M.; Baker, D. R.

2006-12-01

Because in situ observations of actively growing surfaces are technically impractical, our understanding of crystal growth mechanisms at hydrothermal and magmatic conditions lags behind that of minerals that can be grown from aqueous solutions at or near room temperature. Growing silicate minerals from hydrous synthetic carbonate melts offers the opportunity to relate directly minor element incorporation to their surface microtopography. Natural hydrothermal diopside was used to seed experiments in which synthetic clinopyroxene crystals were grown at 800 degrees C and 10 kbars for 24 hours, from alkaline melts modelled after the lavas of the Tanzanian volcano Oldoinyo Lengai. The melts were prepared from Na2CO3, K2CO3, CaCO3, MgCO3 and Fe3O4 reagents. One run was anhydrous and the others contained either 2.5 or 5 wt. % H2O. Euhedral tabular crystals ranging in size from 100 to 300 ìm across were found in all three runs, hand-picked and freed from their carbonate matrix by overnight immersion in dilute acetic acid. The crystals consist of \\{110\\} prism, \\{100\\} and \\{001\\} pinacoids and a \\{111\\} dipyramid. AFM images resolved a distinct surface microtopography on each form: arrays of broad macrosteps on \\{100\\}, lens- shaped islands on \\{001\\} facets and striated fiber-like crystallites on \\{110\\}. EMP analyses of polished grain mounts show that compositional zoning of Na and Fe occurs not only among non-equivalent growth sectors but also within single \\{100\\} sectors. Electron microprobe maps of sequentially polished sections indicate that zoning within \\{100\\} sectors reflects differential uptake of Na and Fe on symmetrically non-equivalent steps. Near the crystal surface, the non- equivalent coeval vicinal faces of growth hillocks on \\{100\\} are either diopside-like, Na.007Ca1.00(Mg0.754Fe2+0.22Mn2+0.013Al_{0.003)Si2.00O6 , or acmitic, Ca0.63Na0.35(Mg0.64Fe3+ 0.36)Al0.01Si1.99O6 in composition. Step-specific incorporation of minor elements in a clinopyroxene face has only been documented once, in a hydrothermal diopside from Orford (Quebec), where Fe(II) and Mn(II) were differentially incorporated on steps oriented parallel to [010] on \\{100\\} faces. This natural example and our synthetic crystals reflect growth regimes where minor element incorporation was limited by surface-structural kinetics rather than diffusion- controlled kinetics. Such step-specific surface-structural control has never been reported in clinopyroxenes grown from silicate melts. Is it present, but more subtle, or do silicate melts promote a significantly different growth regime? Comparing zoning patterns in synthetic silicates grown from carbonate versus silicate melts could put new constraints on current models of element partitioning.

Partitioning of carbon between Fe-rich alloy melt and silicate melt in a magma ocean - Implications for the abundance and origin of volatiles in Earth, Mars, and the Moon

NASA Astrophysics Data System (ADS)

Chi, Han; Dasgupta, Rajdeep; Duncan, Megan S.; Shimizu, Nobumichi

2014-08-01

The budget and origin of carbon in Earth and other terrestrial planets are debated and one of the key unknowns is the fate of carbon during early planetary processes including accretion, core formation, and magma ocean (MO) crystallization. Here we determine, experimentally, the solubility of carbon in coexisting Fe-Ni alloy melt and basaltic silicate melt in shallow MO conditions, i.e., at 1-3 GPa, 1500-1800 °C. Oxygen fugacity of the experiments, estimated based on Fe (in metallic alloy melt)-FeO (in silicate melt) equilibrium, varied between ∼IW-0.4 and IW-1.0, where IW refers to the oxygen fugacity imposed by the coexistence of iron and wüstite. Four different starting mixes, each with 7:3 silicate:metal mass ratio and silicate melt NBO/T (estimated proportion of non-bridging oxygen with respect to tetrahedral cations; NBO/T=2×/total OT -4, where T = Si + Ti + Al + Cr + P) ranging from 0.81 to 1.54 were studied. Concentrations of carbon in the alloy melt were determined using electron microprobe whereas carbon contents of quenched basaltic glasses were determined using secondary ionization mass spectrometry (SIMS). Identification of carbon and hydrogen-bearing species in silicate glasses was performed using Raman and Fourier Transformed Infrared (FTIR) spectroscopy. Our results show that carbon in the metallic melt varies between 4.4 wt.% and 7.4 wt.% and increases with increasing temperature and modestly with increasing pressure but decreases with increasing Ni content of the alloy melt. Carbon concentration in the silicate melts, on the other hand, varies from 11 ± 1 ppm to 111 ± 7 ppm and is negatively correlated with pressure but positively correlated with temperature, the NBO/T, the oxygen fugacity and the water content of the silicate melts. Raman and FTIR results show that at our experimental conditions, carbon in silicate melt is dissolved both as hydrogenated species and CO32-. The calculated carbon partition coefficient DCmetal/silicate varies from 510 ± 53 to 5369 ± 217 and varies systematically as a function of P, T, fO2, water content, the composition of the silicate melt (expressed using NBO/T), and Ni content of alloy melt (XNi). The range of DCmetal/silicate measured in our study with carbonated and hydrogenated carbon species in silicate melt is similar to that reported in the literature for experiments where carbonyl complexes are the chief carbon species in silicate melts. A parameterization was derived using the data from this and existing studies such as lnDCmetal/silicate=a/T+b·P/T+c·ln(fO2)+d·(NBO/T)+e·ln(1-XNi)+f where a = -33,510, b = 1357, c = -0.596, d = -1.182, e = 4.15, f = 13.38, the temperature is in Kelvin, and the pressure is in gigapascal. Using this parameterization and the estimated conditions for the base of the MOs, the average DCmetal/silicate value for Earth, Mars, and the Moon can be predicted. The deep MO of Earth is predicted to cause the strongest depletion of its silicate carbon budget, closely followed by Mars with intermediate depth MO, and then the Moon with a shallow MO. We predict that the lunar mantle carbon budget, similar to that of the Earth’s present-day upper mantle, might have been set by equilibrium core-mantle fractionation in MO; whereas for Earth, later processes such as ingassing from a proto-atmosphere and late-stage accretion of volatile-rich material was necessary for delivery of carbon and other volatiles. Finally, the comparison of our measured and predicted value of DCmetal/silicate for terrestrial MO with similar constraints on DNmetal/silicate from the literature suggests that the apparent depletion of nitrogen relative to carbon for the bulk silicate Earth and the Earth’s upper mantle is unlikely to be caused by preferential partitioning of nitrogen to alloy melt during core formation.

Spinodal decomposition in amorphous metal-silicate thin films: Phase diagram analysis and interface effects on kinetics

NASA Astrophysics Data System (ADS)

Kim, H.; McIntyre, P. C.

2002-11-01

Among several metal silicate candidates for high permittivity gate dielectric applications, the mixing thermodynamics of the ZrO2-SiO2 system were analyzed, based on previously published experimental phase diagrams. The driving force for spinodal decomposition was investigated in an amorphous silicate that was treated as a supercooled liquid solution. A subregular model was used for the excess free energy of mixing of the liquid, and measured invariant points were adopted for the calculations. The resulting simulated ZrO2-SiO2 phase diagram matched the experimental results reasonably well and indicated that a driving force exists for amorphous Zr-silicate compositions between approx40 mol % and approx90 mol % SiO2 to decompose into a ZrO2-rich phase (approx20 mol % SiO2) and SiO2-rich phase (>98 mol % SiO2) through diffusional phase separation at a temperature of 900 degC. These predictions are consistent with recent experimental reports of phase separation in amorphous Zr-silicate thin films. Other metal-silicate systems were also investigated and composition ranges for phase separation in amorphous Hf, La, and Y silicates were identified from the published bulk phase diagrams. The kinetics of one-dimensional spinodal decomposition normal to the plane of the film were simulated for an initially homogeneous Zr-silicate dielectric layer. We examined the effects that local stresses and the capillary driving force for component segregation to the interface have on the rate of spinodal decomposition in amorphous metal-silicate thin films.

In situ insights to Se (S) partitioning between silicate and metallic melts at extreme conditions

NASA Astrophysics Data System (ADS)

Borchert, M.; Petitgirard, S.; Appel, K.; Watenphul, A.; Morgenroth, W.

2012-12-01

The Earth's core mainly consists of a metallic Fe-Ni mixture. However, seismic observations show that the density is about 5-10% lower than expected for an Fe-Ni alloy under similar pressure and temperature conditions (e.g., [1,2]). This discovery initiated numerous studies to identify and quantify light elements in the Earth0s core. Among others, sulphur has been suggested to be a promisingly candidate to alloy with the metallic core because of its depletion in the crust and the mantle relative to other volatile elements by several orders of magnitude (e.g., [3-5]). In the last decades, several experimental studies have aimed to quantify the sulphur content in the Earth's core and to determine its influence on the physical properties (e.g., [6]). However, experimental data on sulphur partitioning between silicate and metallic liquids at pressures and temperatures relevant for core-mantle boundary conditions are missing. This lack is due to pressure and temperature limitations of conventional experimental approaches (up to 25 GPa and 2200 K). New developments, like laser-heated diamond-anvil cells (LDAC), allow studies at core-mantle boundary conditions, but in-situ chemical analysis of sulphur in LDACs is impossible due to the high absorption of S fluorescence in the diamonds. Instead of sulphur, selenium can be used to model sulphur partitioning between silicate and metallic melts at elevated PT conditions. This is based on the fact that sulphur and selenium can be considered as geochemical twins ([7,8]). The main advantage of this approach is the much higher excitation energy of selenium compared to sulphur, which enables in-situ XRF analysis in LDACs. Here, we present preliminary data on Se partitioning between silicate and metallic melt at extreme conditions. The experiments have been performed in double-sided laser-heated LDACs at the high pressure beamlines P02.2 (DESY, Germany) and ID27 (ESRF, France) as described in [9]. Micro-XRF mappings are used to visualise changes of the Se distribution before and after laser heating. Micro-XRD is used to determine the experimental pressure, the onset of melting and also provides information on distribution of high-pressure / high temperature phases (XRD map). In order to fully apply the observed in-situ Se results to the S partitioning, the recovered samples will be additionally analysed ex-situ for Se and S by EMP, SEM and HRTEM. This will also set constraints on the effect of quenching. [1] Birch (1952) J. Geophys. Res. 57, 227-286. [2] McDonough (2003) Treatise on Geochemistry, Vol. 2, pp. 547-568. [3] Manson (1966) Nature 211, 616-618. [4] Rama Murthy and Hall (1970) Phys. Earth. Planet. Inter. 2, 276-282. [5] Dreibus and Palme (1996) Geochim. Cosmochim Acta. 60, 1125-1130. [6] Morard et al. (2008) Earth. Planet Sci Lett. 272, 620-626. [7] Jenner et al. (2009) Geostand. Geoanal. Res. 33, 309-317. [8] Wykes et al. (2010) Ontario Geological Survey, Miscellaneous Release-Data 269. [9] Petitgirard et al. (2012) Rev. Sci. Instrum. 83, 013904.

Protective Coating For Laser Drilling Of Silicon

NASA Technical Reports Server (NTRS)

Shlichta, Paul J.

1988-01-01

Sodium silicate prevents spattered silicon from fusing with surrounding material. Sodium silicate solution applied to wafer by dipping and draining or by spinning; application by spraying also works. When dried in oven, solution leaves thin coating of sodium silicate glass.

Geologic map of the Maumee quadrangle, Searcy and Marion Counties, Arkansas

USGS Publications Warehouse

Turner, Kenzie J.; Hudson, Mark R.

2010-01-01

This map summarizes the geology of the Maumee 7.5-minute quadrangle in northern Arkansas. The map area is in the Ozark plateaus region on the southern flank of the Ozark dome. The Springfield Plateau, composed of Mississippian cherty limestone, overlies the Salem Plateau, composed of Ordovician carbonate and clastic rocks, with areas of Silurian rocks in between. Erosion related to the Buffalo River and its tributaries, Tomahawk, Water, and Dry Creeks, has exposed a 1,200-ft-thick section of Mississippian, Silurian, and Ordovician rocks mildly deformed by faults and folds. An approximately 130-mile-long corridor along the Buffalo River forms the Buffalo National River that is administered by the National Park Service. McKnight (1935) mapped the geology of the Maumee quadrangle as part of a larger 1:125,000-scale map focused on understanding the lead and zinc deposits common in the area. Detailed new mapping for this study was compiled using a Geographic Information System (GIS) at 1:24,000 scale. Site location and elevation were obtained by using a Global Positioning Satellite (GPS) receiver in conjunction with a U.S. Geological Survey 7.5-minute topographic map and barometric altimeter. U.S. Geological Survey 10-m digital elevation model data were used to derive a hill-shade-relief map used along with digital orthophotographs to map ledge-forming units between field sites. Bedding attitudes were measured in drainage bottoms and on well-exposed ledges. Bedding measured at less than 2 degree dip is indicated as horizontal. Structure contours constructed for the base of the Boone Formation are constrained by field-determined elevations on both upper and lower formation contacts.

Architecture of near-surface magma transport in the Columbia River Flood Basalts as defined by a career's worth of feeder dike mapping: The legacy dataset of William H. Taubeneck

NASA Astrophysics Data System (ADS)

Karlstrom, L.; Morriss, M. C.; Nasholds, M. W.

2016-12-01

The Miocene Columbia River Flood Basalts (CRFB) are the youngest, best preserved, and most thoroughly studied Large Igneous Province on Earth. The Grande Ronde basalts erupted 150,000 km3in less than 100 kyr ( 72% of the CRFB volume) from a network of feeder dikes, the Chief Joseph dike swarm, exposed in SE Washington, NE Oregon, and W Idaho, USA. William H. Taubeneck (1923-2016) spent several decades mapping CRFB dikes. His extensive, meticulous field work defined the spatial extent and dominant trends in the Chief Joseph dike swarm, providing a key constraint for theories of CRFB emplacement and their deep origin. However, these measurements were never published nor made public. We are revitalizing Taubeneck's maps, notebooks, and numerous unpublished geochemical analyses, synthesizing his work with other published and mapped dikes and field checking select measurements to ensure accurate interpretation. This dataset should lead to increased understandings of the CRFB shallow plumbing system and flood basalt eruptive dynamics in general. Preliminary analysis of 4,410 mapped CRFB feeder dike segments from Taubeneck and other workers reveals systematic trends in both dike orientation and lithology of host rock. Average dike orientation strikes to the north-northwest across 400 km. Orientations are generally parallel to the cratonic boundary, but appear generally unaffected by a major transition in craton position and also exhibit minor trends with near orthogonal orientations. Dike spatial density peaks in Paleozoic to Cenozoic accreted terranes. Exposed dikes are concentrated among Jurassic and Cretaceous plutons, which host 53% of mapped dikes and accommodate the largest variability in dike orientation. Preliminary investigations suggest variations of feeder dike thickness with depth in the plumbing system as preserved through exposure in the uplifted Wallowa Mountains, although this is complicated by evidence for dikes that accommodated multiple injections and uncertain duration of flow. Ongoing work aims to resolve these issues. Summary figure: (a) Dikes mapped by Taubeneck and others versus latitude. (b) Dike orientation. (c) Paleozoic and Mesozoic accreted terranes and the cratonic margin. Dikes are mostly exposed in the Baker and Wallowa Terranes. (d) Dike host rock lithology.

Pyrolytic Synthesis of Carbon Nanotubes from Sucrose on a Mesoporous Silicate

NASA Technical Reports Server (NTRS)

Abdel-Fattah, Tarek; Siochi, Mia; Crooks, Roy

2005-01-01

Multiwall carbon nanotubes were synthesized from sucrose by a pyrolytic technique using mesoporous MCM-41 silicate templates without transition metal catalysts. The Nanotubes were examined in the carbon/silicate composite and after dissolution of the silicate. High resolution transmission electron microscopy study of the multiwall nanotubes showed them to be 15 nm in diameter, 200 nm in length and close-ended. There was variation in crystallinity with some nanotubes showing disordered wall structures.

Reagentless and calibrationless silicate measurement in oceanic waters.

PubMed

Giraud, William; Lesven, Ludovic; Jońca, Justyna; Barus, Carole; Gourdal, Margaux; Thouron, Danièle; Garçon, Véronique; Comtat, Maurice

2012-08-15

Determination of silicate concentration in seawater without addition of liquid reagents was the key prerequisite for developing an autonomous in situ electrochemical silicate sensor (Lacombe et al., 2007) [11]. The present challenge is to address the issue of calibrationless determination. To achieve such an objective, we chose chronoamperometry performed successively on planar microelectrode (ME) and ultramicroelectrode (UME) among the various possibilities. This analytical method allows estimating simultaneously the diffusion coefficient and the concentration of the studied species. Results obtained with ferrocyanide are in excellent agreement with values of the imposed concentration and diffusion coefficient found in the literature. For the silicate reagentless method, successive chronoamperometric measurements have been performed using a pair of gold disk electrodes for both UME and ME. Our calibrationless method was tested with different concentrations of silicate in artificial seawater from 55 to 140×10(-6) mol L(-1). The average value obtained for the diffusion coefficient of the silicomolybdic complex is 2.2±0.4×10(-6) cm(2) s(-1), consistent with diffusion coefficient values of molecules in liquid media. Good results were observed when comparing known concentration of silicate with experimentally derived ones. Further work is underway to explore silicate determination within the lower range of oceanic silicate concentration, down to 0.1×10(-6) mol L(-1). Copyright © 2012 Elsevier B.V. All rights reserved.

Quantitative Trait Loci for Resistance to Aspergillus Ear Rot: Analysis by Linkage Mapping, Characterization of Near-Isogenic Lines and Meta-Analysis

USDA-ARS?s Scientific Manuscript database

High levels of aflatoxin contamination of maize can be deadly for exposed human populations. Resistance to aflatoxin accumulation in maize has been reported in multiple studies and acts at multiple steps where there is fungal-plant interaction. In this study, we report the identification and mapping...

MAPPING INTERTIDAL EELGRASS (ZOSTERA MARINA L.) IN THREE COASTAL ESTUARIES OF THE PACIFIC NORTHWEST USA USING FALSE-COLOUR NEAR-INFRARED AERIAL PHOTOGRAPHY

EPA Science Inventory

This study describes a hybrid technique of digitally classifying aerial photography used for mapping the intertidal habitat of eelgrass (Zostera marina L.) in Pacific Northwest USA estuaries. The large tidal range (2-3 m) in this region exposes most of this seagrass community at ...

The ontogeny of the homing pigeon navigational map: evidence for a sensitive learning period.

PubMed Central

Gagliardo, A; Ioalè, P; Odetti, F; Bingman, V P

2001-01-01

Homing pigeons can learn a navigational map by relying on the heterogeneous distribution of atmospheric odours in the environment. To test whether there might be a sensitive period for learning an olfactory-based navigational map, we maintained a group of young pigeons in an aviary screened from the winds until the age of three to four months post-fledging. Subsequently, the screens were removed and the pigeons were exposed to the winds and the environmental odours they carry for three months. One control group of pigeons was held in a similar aviary but exposed to the winds immediately upon Hedging, while another control group of pigeons was allowed free-flight. When the pigeons from the three groups were released from two distant release sites at about six months of age post-fledging, the two control groups were found to be equally good at orientating and returning home, while the experimental pigeons held in the shielded aviary for the first three months post-fledging were unable to orientate homeward and they were generally unsuccessful in returning home. This result supports the hypothesis that environmental experience during the first three months post-fledging is critical for some aspect of navigational map learning and that navigational map learning displays sensitive period-like properties. PMID:11209891

The ontogeny of the homing pigeon navigational map: evidence for a sensitive learning period.

PubMed

Gagliardo, A; Ioalè, P; Odetti, F; Bingman, V P

2001-01-22

Homing pigeons can learn a navigational map by relying on the heterogeneous distribution of atmospheric odours in the environment. To test whether there might be a sensitive period for learning an olfactory-based navigational map, we maintained a group of young pigeons in an aviary screened from the winds until the age of three to four months post-fledging. Subsequently, the screens were removed and the pigeons were exposed to the winds and the environmental odours they carry for three months. One control group of pigeons was held in a similar aviary but exposed to the winds immediately upon Hedging, while another control group of pigeons was allowed free-flight. When the pigeons from the three groups were released from two distant release sites at about six months of age post-fledging, the two control groups were found to be equally good at orientating and returning home, while the experimental pigeons held in the shielded aviary for the first three months post-fledging were unable to orientate homeward and they were generally unsuccessful in returning home. This result supports the hypothesis that environmental experience during the first three months post-fledging is critical for some aspect of navigational map learning and that navigational map learning displays sensitive period-like properties.

The effects of sulfide composition on the solubility of sulfur in coexisting silicate melts

NASA Astrophysics Data System (ADS)

Smythe, Duane; Wood, Bernard; Kiseeva, Ekaterina

2016-04-01

The extent to which sulfur dissolves in silicate melts saturated in an immiscible sulfide phase is a fundamental question in igneous petrology and plays a primary role in the generation of magmatic ore deposits, volcanic degassing and planetary differentiation. Terrestrial sulfide melts often contain over 20 weight percent Ni + Cu, however, most experimental studies investigating sulfur solubility in silicate melt have been primarily concerned with the effects of silicate melt composition, and pure FeS has been use as the immiscible sulfide melt (O'Neill and Mavrogenes, 2002; Li and Ripley, 2005). To investigation of the effects of sulfide composition, in addition to those of temperature, pressure and silicate melt composition, on sulfur solubility in silicate melts, we have carried out a series of experiments done at pressures between 1.5 and 3 GPa and temperatures from 1400 to 1800C over a range of compositions of both the silicate and sulfide melt. We find that the solubility of sulfur in silicate melts drops significantly with the substitution of Ni and Cu for Fe in the immiscible sulfide melt, decreasing by approximately 40% at mole fractions of NiS + Cu2S of 0.4. Combining our results with those from the previous studies investigating sulfur solubility in silicate melts we have also found that solubility increases with increasing temperature and decreases pressure. These results show that without considering the composition of the immiscible sulfide phase the sulfur content of silicate melts can be significantly overestimated. This may serve to explain the relatively low sulfur concentrations in MORB melts, which previous models predict to be undersaturated in a sulfide phase despite showing chemical and textural evidence for sulfide saturation. Li, C. & Ripley, E. M. (2005). Empirical equations to predict the sulfur content of mafic magmas at sulfide saturation and applications to magmatic sulfide deposits. Mineralium Deposita 40, 218-230. O'Neill, H. S. C. & Mavrogenes, J. A. (2002). The Sulfide Capacity and the Sulfur Content at Sulfide Saturation of Silicate Melts at 1400°C and 1 bar. Journal of Petrology 43, 1049-1087.

Perlite toxicology and epidemiology--a review.

PubMed

Maxim, L Daniel; Niebo, Ron; McConnell, Ernest E

2014-04-01

Perlite is a generic name for an amorphous volcanic alumina-silicate rock that expands by a factor of 4-20 when rapidly heated to 1400-1800 °F (760-980 °C). Both the ore and the expanded product have extensive and widespread commercial applications. Limited data on the toxicology of perlite in animal studies indicate that the LD₅₀ (oral ingestion) is more than 10 g/kg and, from a chronic inhalation study in guinea pigs and rats, that the NOAEL for the inhalation pathway is 226 mg/m³. Health surveillance studies of workers in US perlite mines and expansion plants (including some workers exposed to levels greater than prevailing occupational exposure limits (OELs) conducted over 20 years indicate that the respiratory health of workers is not adversely affected. Studies in Turkish mines and expanding plants had generally similar results, but are more difficult to interpret because of high smoking rates in these populations. A recent mortality study of permanent residents of the island of Milos (Greece) exposed to various mining dusts (including perlite) resulted in non-significant increases in standard mortality ratios for pneumonia and chronic obstructive pulmonary disease (COPD), whereas a companion morbidity study revealed elevated odds ratios for allergic rhinitis, pneumonia, and COPD when compared to another industrial area of Greece. Residents were exposed to other mining dusts and other possible causes or contributing factors and no ambient monitoring data were presented so it is not possible to use this study for risk calculations of perlite-exposed populations. Perlite is regulated as a "nuisance dust" in most countries.

Accessing Martian Fluvial and Lacustrine Sediments by Landing in Holden Crater, Margaritifer Sinus

NASA Technical Reports Server (NTRS)

Parker, T. J.; Grant, J. A.

2001-01-01

Rover missions to the surface of Mars after MER 2003, are likely to be centered around focused geologic field mapping. One objective with high priority in selecting landing sites for these missions will be to characterize the nature, spatial distribution, internal structure, composition, and depositional history of exposed sedimentary layered deposits by visiting a number of distributed outcrops identified previously (and with a high degree of certainty) from orbit. These deposits may contain prebiotic material, even fossil organisms, but their primary value will be to enable an assessment of the planet's climate at the time they were emplaced. High resolution imaging from a mobile rover will enable the detailed study of these deposits over a wide area, their internal structure and mineralogy at distributed localities, and could resolve biologically-derived structures (such as stromatolite-like textures) if they are present. With the addition of a spectrometer, it should be possible to ascertain the presence of carbonates, sulfates, organics, water (liquid, frost, and bound water), as well as a variety of silicate minerals in the context of the collected imagery. Such a mission approach is directly relevant to future exploration of Mars, because it provides the geologic context comparable to what a field geologist visiting a site for the first time would acquire. Rover missions after MER will likely have much better targeting and hazard avoidance landing systems, enabling access to planimetrically-challenged sites of high scientific interest. These vehicles will also likely have greater mobility than MER, capable of driving greater distances in a shorter amount of time. Many scientists and mission planners have realized the need to design a rover whose mobility can be comparable to the dimensions of its 3-sigma landing error ellipse.

Search for Extralunar Materials in Apollo Soil Samples

NASA Astrophysics Data System (ADS)

Lucey, P. G.; Honniball, C.; Crites, S.; Taylor, G. J.; Martel, L.

2017-12-01

It has long been proposed that the lunar surface is a pristine collector of material from across the solar system. The Moon is exposed to the same meteorite flux as the Earth, but because its surface is unaltered by processes such as plate tectonics, aqueous alteration, or recent volcanism, the Moon may have recorded a much longer meteoritic history than the chemically and physically active Earth. By studying lunar soils at the individual grain level, we have the potential to identify and study material from across the inner solar system. We have developed three hyperspectral imaging microscopes to search a large quantity of lunar soil grains for rare lunar, and extra-lunar minerals. We are using lunar-exotic mineralogy as a tracer to detect extralunar candidates. One hyperspectral microscope covers the 1-2.5 micron region for detection of water and hydroxyl overtones in alteration minerals such as phyllosilicates. The second instrument covers the 2.5 to 5 micron region to characterize the 3 micron water region, and for detection of organics and carbonates. The third covers the thermal infrared for detection of phosphates and zeolites as well as the major lunar silicates. We are examining 1 million grains of varying sizes from Apollo 11 ,12, 14 and 16 landing sites. Using the USGS spectral library and the Tetracorder mineral mapping algorithm, we are matching library mineral spectra with the grain spectra we acquire. To validate our ability to detect and match mineral spectra, we are conducting scans of relevent mineral seperates and mixtures at the individual grain level. Results of this mineral inventory will provide contraints on various models and estimates for material transfer between the terrestrial planets.

Field reconnaissance geologic mapping of the Columbia Hills, Mars, based on Mars Exploration Rover Spirit and MRO HiRISE observations

USGS Publications Warehouse

Crumpler, L.S.; Arvidson, R. E.; Squyres, S. W.; McCoy, T.; Yingst, A.; Ruff, S.; Farrand, W.; McSween, Y.; Powell, M.; Ming, D. W.; Morris, R.V.; Bell, J.F.; Grant, J.; Greeley, R.; DesMarais, D.; Schmidt, M.; Cabrol, N.A.; Haldemann, A.; Lewis, K.W.; Wang, A.E.; Schroder, C.; Blaney, D.; Cohen, B.; Yen, A.; Farmer, J.; Gellert, Ralf; Guinness, E.A.; Herkenhoff, K. E.; Johnson, J. R.; Klingelhfer, G.; McEwen, A.; Rice, J.W.; Rice, M.; deSouza, P.; Hurowitz, J.

2011-01-01

Chemical, mineralogic, and lithologic ground truth was acquired for the first time on Mars in terrain units mapped using orbital Mars Reconnaissance Orbiter's High Resolution Imaging Science Experiment (MRO HiRISE) image data. Examination of several dozen outcrops shows that Mars is geologically complex at meter length scales, the record of its geologic history is well exposed, stratigraphic units may be identified and correlated across significant areas on the ground, and outcrops and geologic relationships between materials may be analyzed with techniques commonly employed in terrestrial field geology. Despite their burial during the course of Martian geologic time by widespread epiclastic materials, mobile fines, and fall deposits, the selective exhumation of deep and well-preserved geologic units has exposed undisturbed outcrops, stratigraphic sections, and structural information much as they are preserved and exposed on Earth. A rich geologic record awaits skilled future field investigators on Mars. The correlation of ground observations and orbital images enables construction of a corresponding geologic reconnaissance map. Most of the outcrops visited are interpreted to be pyroclastic, impactite, and epiclastic deposits overlying an unexposed substrate, probably related to a modified Gusev crater central peak. Fluids have altered chemistry and mineralogy of these protoliths in degrees that vary substantially within the same map unit. Examination of the rocks exposed above and below the major unconformity between the plains lavas and the Columbia Hills directly confirms the general conclusion from remote sensing in previous studies over past years that the early history of Mars was a time of more intense deposition and modification of the surface. Although the availability of fluids and the chemical and mineral activity declined from this early period, significant later volcanism and fluid convection enabled additional, if localized, chemical activity. Copyright ?? 2011 by the American Geophysical Union.

DEMONSTRATION BULLETIN: SOLIDIFICATION/STABILIZATION OF ORGANIC/INORGANIC CONTAMINANTS - SILICATE TECHNOLOGY CORPORATION

EPA Science Inventory

Silicate Technology Corporation's (STC's) technology for treating hazardous waste utilizes silicate compounds to stabilize organic and inorganic constituents in contaminated soils and sludges. STC has developed two groups of reagents: SOILSORB HM for treating wastes with inorgan...

Wind-Eroded Silicate as a Source of Hydrogen Peroxide on Mars

NASA Astrophysics Data System (ADS)

Bak, E. N.; Merrison, J. P.; Jensen, S. K.; Nørnberg, P.; Finster, K.

2014-07-01

Laboratory simulations show that wind-eroded silicate can be a source of hydrogen peroxide. The ubiquitous, fine-grained silicate dust might thus explain the oxidizing properties of the martian soil and affect the preservation of organic compounds.

Understanding Vesuvius magmatic processes: Evidence from primitive silicate-melt inclusions in medieval scoria clinopyroxenes (Terzigno formation)

USGS Publications Warehouse

Lima, A.; Belkin, H.E.; Torok, K.

1999-01-01

Microthermometric investigations of silicate-melt inclusions and electron microprobe analyses were conducted on experimentally homogenized silicate-melt inclusions and on the host clinopyroxenes from 4 scoria samples of different layers from the Mt. Somma-Vesuvius medieval eruption (Formazione di Terzigno, 893 A.D.). The temperature of homogenization, considered the minimum trapping temperature, ranges from 1190 to 1260??5 ??C for all clinopyroxene-hosted silicate melt inclusions. The major and minor-element compositional trends shown by Terzigno scoria and matrix glass chemical analysis are largely compatible with fractional crystallization of clinopyroxene and Fe-Ti oxides. Sulfur contents of the homogenized silicate-melt inclusions in clinopyroxene phenocrysts compared with that in the host scoria show that S has been significantly degassed in the erupted products; whereas, Cl has about the same abundance in the inclusions and in host scoria. Fluorine is low (infrequently up to 800 ppm) in the silicate-melt inclusions compared to 2400 ppm in the bulk scoria. Electron microprobe analyses of silicate-melt inclusions show that they have primitive magma compositions (Mg# = 75-91). The composition of the host clinopyroxene phenocrysts varies from typical plinian-related (Mg#???85) to non-plinian related (Mg#???85). The mixed source of the host clinopyroxenes and primitive nature of the silicate-melt inclusions implies that these phenocrysts, in part, may be residual and/or have a polygenetic origin. The similar variation trends of major and minor-elements between homogenized silicate-melt inclusions from the Terzigno scoria, and silicate-melt inclusions in olivine and diopside phenocrysts from plinian eruptions (Marianelli et al., 1995) suggest that the trapped inclusions represent melts similar to those that supplied the plinian and sub-plinian magma chambers. These geochemical characteristics suggest that the Vesuvius magmatic system retained a vestige of the most recent plinian event.

Cometary crystalline silicate before and after perihelion passage II

NASA Astrophysics Data System (ADS)

Ootsubo, Takafumi

2014-01-01

Crystalline silicate is often observed in comets as an 11.3-micron resonant emission feature, and may be used for probing the early solar nebula. Because the formation of the crystalline silicate requires high temperature, they are thought to have been born from amorphous silicate at the inner region, and then transported toward the outer regions where comets were born. This transportation can produce the difference in the crystalline fraction in the cometary silicate dust between two dynamical types of comets, Oort-cloud comets (OCs) and Ecliptic comets (ECs), due to the different heliocentric distances of their birth places. The study of peak wavelengths in crystalline features is important to investigate the conditions of the crystalline silicate formation as well. Thus far, we don't have enough observational samples of OCs. Fortunately, we can observe comet C/2012 K1 (PanSTARRS) along with C/2013 A1 (Siding Spring) in this semester. In particular, the comet C/2012 K1 (PanSTARRS) is a bright and good target for this silicate peak feature study. Observations at pre- and post-perihelion provide us precious information on the dust evolution of the comet.

A SYSTEMATIC SEARCH FOR THE SPECTRA WITH FEATURES OF CRYSTALLINE SILICATES IN THE SPITZER IRS ENHANCED PRODUCTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Rui; Luo, Ali; Liu, Jiaming

2016-06-01

The crystalline silicate features are mainly reflected in infrared bands. The Spitzer Infrared Spectrograph (IRS) collected numerous spectra of various objects and provided a big database to investigate crystalline silicates in a wide range of astronomical environments. We apply the manifold ranking algorithm to perform a systematic search for the spectra with crystalline silicate features in the Spitzer IRS Enhanced Products available. In total, 868 spectra of 790 sources are found to show the features of crystalline silicates. These objects are cross-matched with the SIMBAD database as well as with the Large Sky Area Multi-object Fiber Spectroscopic Telescope (LAMOST)/DR2. Themore » average spectrum of young stellar objects shows a variety of features dominated either by forsterite or enstatite or neither, while the average spectrum of evolved objects consistently present dominant features of forsterite in AGB, OH/IR, post-AGB, and planetary nebulae. They are identified optically as early-type stars, evolved stars, galaxies and so on. In addition, the strength of spectral features in typical silicate complexes is calculated. The results are available through CDS for the astronomical community to further study crystalline silicates.« less

Increase of Elderly Population in the Rainstorm Hazard Areas of China.

PubMed

Liang, Pujun; Xu, Wei; Ma, Yunjia; Zhao, Xiujuan; Qin, Lianjie

2017-08-26

In light of global warming, increased extreme precipitation events have enlarged the population exposed to floods to some extent. Extreme precipitation risk assessments are of great significance in China and allow for the response to climate change and mitigation of risks to the population. China is one of the countries most influenced by climate change and has unique national population conditions. The influence of extreme precipitation depends on the degree of exposure and vulnerability of the population. Accurate assessments of the population exposed to rising rainstorm trends are crucial to mapping extreme precipitation risks. Studying the population exposed to rainstorm hazard areas (RSHA) at the microscale is extremely urgent, due to the local characteristics of extreme precipitation events and regional diversity of the population. The spatial distribution of population density was mapped based on the national population census data from China in 1990, 2000 and 2010. RSHA were also identified using precipitation data from 1975-2015 in China, and the rainstorm tendency values were mapped using GIS in this paper. The spatial characteristics of the rainstorm tendencies were then analyzed. Finally, changes in the population in the RSHA are discussed. The results show that the extreme precipitation trends are increasing in southeastern China. From 1990 to 2010, the population in RSHA increased by 110 million, at a rate of 14.6%. The elderly in the region increased by 38 million at a rate of 86.4%. Studying the size of the population exposed to rainstorm hazards at the county scale can provide scientific evidence for developing disaster prevention and mitigation strategies from the bottom up.

Analysis of tsunami disaster map by Geographic Information System (GIS): Aceh Singkil-Indonesia

NASA Astrophysics Data System (ADS)

Farhan, A.; Akhyar, H.

2017-02-01

Tsunami risk map is used by stakeholder as a base to decide evacuation plan and evaluates from disaster. Aceh Singkil district of Aceh- Indonesia’s disaster maps have been developed and analyzed by using GIS tool. Overlay methods through algorithms are used to produce hazard map, vulnerability, capacity and finally created disaster risk map. Spatial maps are used topographic maps, administrative map, SRTM. The parameters are social, economic, physical environmental vulnerability, a level of exposed people, parameters of houses, public building, critical facilities, productive land, population density, sex ratio, poor ratio, disability ratio, age group ratio, the protected forest, natural forest, and mangrove forest. The results show high-risk tsunami disaster at nine villages; moderate levels are seventeen villages, and other villages are shown in the low level of tsunami risk disaster.

Genetic Influences on Survival Time After Severe Hemorrhage in Inbred Rat Strains

DTIC Science & Technology

2011-04-12

technique (10, 41) immediately after insertion of the carotid catheter. A second incision was made in the skin in the medial aspect of the thigh to expose...rat strains. Both baseline and post hemorrhage mean arterial pres- sures (MAP) differed among inbred rat strains as did the decrease in MAP produced...measure for a given strain are different (P 0.05) between experiments for that strain. Mean arterial pressure (MAP) was recorded at 1 min prior to

SILICATES FOR CORROSION CONTROL IN BUILDING POTABLE WATER SYSTEMS

EPA Science Inventory

Silicates have been used to control the corrosion of drinking water distribution system materials. Previous work has shown that they are particularly useful in reducing the release of zinc from galvanized materials in hot water systems. Negatively charged silicate species were re...

COORDINATED ANALYSES OF PRESOLAR GRAINS IN THE ALLAN HILLS 77307 AND QUEEN ELIZABETH RANGE 99177 METEORITES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Ann N.; Nittler, Larry R.; Alexander, Conel M. O'D.

2010-08-10

We report the identification of presolar silicates ({approx}177 ppm), presolar oxides ({approx}11 ppm), and one presolar SiO{sub 2} grain in the Allan Hills (ALHA) 77307 chondrite. Three grains having Si-isotopic compositions similar to SiC X and Z grains were also identified, though the mineral phases are unconfirmed. Similar abundances of presolar silicates ({approx}152 ppm) and oxides ({approx}8 ppm) were also uncovered in the primitive CR chondrite Queen Elizabeth Range (QUE) 99177, along with 13 presolar SiC grains and one presolar silicon nitride. The O-isotopic compositions of the presolar silicates and oxides indicate that most of the grains condensed in low-massmore » red giant and asymptotic giant branch stars. Interestingly, unlike presolar oxides, few presolar silicate grains have isotopic compositions pointing to low-metallicity, low-mass stars (Group 3). The {sup 18}O-rich (Group 4) silicates, along with the few Group 3 silicates that were identified, likely have origins in supernova outflows. This is supported by their O- and Si-isotopic compositions. Elemental compositions for 74 presolar silicate grains were determined by scanning Auger spectroscopy. Most of the grains have non-stoichiometric elemental compositions inconsistent with pyroxene or olivine, the phases commonly used to fit astronomical spectra, and have comparable Mg and Fe contents. Non-equilibrium condensation and/or secondary alteration could produce the high Fe contents. Transmission electron microscopic analysis of three silicate grains also reveals non-stoichiometric compositions, attributable to non-equilibrium or multistep condensation, and very fine scale elemental heterogeneity, possibly due to subsequent annealing. The mineralogies of presolar silicates identified in meteorites thus far seem to differ from those in interplanetary dust particles.« less

Effect of natural fiber types and sodium silicate coated on natural fiber mat/PLA composites: Tensile properties and rate of fire propagation

NASA Astrophysics Data System (ADS)

Thongpin, C.; Srimuk, J.; hipkam, N.; Wachirapong, P.

2015-07-01

In this study, 3 types of natural fibres, i.e. jute, sisal and abaca, were plain weaved to fibre mat. Before weaving, the fibres were treated with 5% NaOH to remove hemi cellulose and lignin. The weaving was performed by hand using square wooden block fit with nails for weaving using one and two types of natural fibres as weft and warp fibre to produce natural fibre mat. The fibre mat was also impregnated in sodium silicate solution extracted from rich husk ash. The pH of the solution was adjusted to pH 7 using H2SO4 before impregnation. After predetermined time, sodium silicate was gelled and deposited on the mat. The fabric mat and sodium silicate coated mat were then impregnated with PLA solution to produce prepreg. Dried pepreg was laminated with PLA sheet using compressing moulding machine to obtain natural fibre mat/PLA composite. The composite containing abaca aligned in longitudinal direction with respect to tension force enhanced Young's modulus more than 300%. Fibre mat composites with abaca aligned in longitudinal direction also showed tensile strength enhancement nearly 400% higher than neat PLA. After coating with sodium silicate, the tensile modulus of the composites was found slightly increased. The silicate coating was disadvantage on tensile strength of the composite due to the effect of sodium hydroxide solution that was used as solvent for silicate extraction from rice husk ash. However, sodium silicate could retard rate of fire propagation about 50%compare to neat PLA and about 10% reduction compared to fibre mat composites without sodium silicate coated fibre mat.

Compositional effects on Si–OH bond length in hydrous silicates with implications for trends in the SiOH acidity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zarubin, Dmitri P., E-mail: dmitri.zarubin@mtu-net.ru

2014-04-01

Theoretical calculations of the structure and Brønsted acidity of SiOH groups in silica clusters have never addressed the question if these vary with the degree of SiOH deprotonation. In this connection, a statistical analysis is presented of Si–OH bond lengths in crystalline hydrogen silicates with well-determined structures with a special emphasis placed on effects of the silicate composition. It is found that among hydrogen silicates of large cations with low charges the Si–OH bonds are always longer than terminal Si–O bonds in the same anion and correlate in length with the anionic charge per tetrahedron. The findings are explained bymore » steric limitations on charge balancing at oxygen atoms by hydrogen bonds and/or cations. It is suggested that similar limitations and imbalances may underlie the well-known trends in the Brønsted acidity of silicic acids and silicas in aqueous media: decreased acidity with increased SiOH deprotonation and increased acidity with increased tetrahedra connectivity. - Graphical abstract: Si–OH bonds in crystalline silicates lengthen with the anionic charge per tetrahedron, which is in parallel with the well-known trend of decreased acidity of silicic acids and silicas in solution with increased degree of deprotonation. - Highlights: • Si–OH bonds in alkali hydrogen silicates are always longer than terminal Si–O bonds. • Si–OH bonds in silicates lengthen with the anionic charge per tetrahedron. • The Si–OH bond elongation results from inherent underbonding of terminal O atoms. • The longer the Si–OH bond, the less acidic the OH group is.« less

Carbonation of metal silicates for long-term CO2 sequestration

DOEpatents

Blencoe, James G; Palmer, Donald A; Anovitz, Lawrence M; Beard, James S

2014-03-18

In a preferred embodiment, the invention relates to a process of sequestering carbon dioxide. The process comprises the steps of: (a) reacting a metal silicate with a caustic alkali-metal hydroxide to produce a hydroxide of the metal formerly contained in the silicate; (b) reacting carbon dioxide with at least one of a caustic alkali-metal hydroxide and an alkali-metal silicate to produce at least one of an alkali-metal carbonate and an alkali-metal bicarbonate; and (c) reacting the metal hydroxide product of step (a) with at least one of the alkali-metal carbonate and the alkali-metal bicarbonate produced in step (b) to produce a carbonate of the metal formerly contained in the metal silicate of step (a).

Carbonation of metal silicates for long-term CO.sub.2 sequestration

DOEpatents

Blencoe, James G [Harriman, TN; Palmer, Donald A [Oliver Springs, TN; Anovitz, Lawrence M [Knoxville, TN; Beard, James S [Martinsville, VA

2012-02-14

In a preferred embodiment, the invention relates to a process of sequestering carbon dioxide. The process comprises the steps of: (a) reacting a metal silicate with a caustic alkali-metal hydroxide to produce a hydroxide of the metal formerly contained in the silicate; (b) reacting carbon dioxide with at least one of a caustic alkali-metal hydroxide and an alkali-metal silicate to produce at least one of an alkali-metal carbonate and an alkali-metal bicarbonate; and (c) reacting the metal hydroxide product of step (a) with at least one of the alkali-metal carbonate and the alkali-metal bicarbonate produced in step (b) to produce a carbonate of the metal formerly contained in the metal silicate of step (a).

Geologic map of the Wildcat Lake 7.5' quadrangle: Kitsap and Mason counties, Washington

USGS Publications Warehouse

Haeussler, Peter J.; Clark, Kenneth P.

2000-01-01

The Wildcat Lake quadrangle lies in the forearc of the Cascadia subduction zone, about 20-km east of the Cascadia accretionary complex exposed in the Olympic Mountains (Tabor and Cady, 1978),and about 100-km west of the axis of the Cascades volcanic arc. The quadrangle lies near the middle of the Puget Lowland, which typically has elevations less than 600 feet (183 m), but on Gold Mountain, in the center of the quadrangle, the elevation rises to 1761 feet (537 m). This anomalously high topography also provides a glimpse of the deeper crust beneath the Lowland. Exposed on Green and Gold Mountains are rocks related to the Coast Range basalt terrane. This terrane consists of Eocene submarine and subaerial tholeiitic basalt of the Crescent Formation, which probably accreted to the continental margin in Eocene time (Snavely and others, 1968). The Coast Range basalt terrane may have originated as an oceanic plateau or by oblique marginal rifting (Babcock and others, 1992), but its subsequent emplacement history is complex (Wells and others, 1984). In southern Oregon, onlapping strata constrain the suturing to have occured by 50 Ma; but on southern Vancouver Island where the terrane-bounding Leech River fault is exposed, Brandon and Vance (1992) concluded suturing to North America occurred in the broad interval between 42 and 24 Ma. After emplacement of the Coast Range basalt terrane, the Cascadia accretionary complex,exposed in the Olympic Mountains west of the quadrangle,developed by frontal accretion and underplating (e.g., Clowes and others, 1987). The Seattle basin, part of which lies to the north of Green Mountain, also began to develop in late Eocene time due to forced flexural subsidence along the Seattle fault zone (Johnson and others, 1994). Domal uplift of the accretionary complex beneath the Olympic Mountains occurred after approximately 18 million years ago (Brandon and others, 1998). Ice-sheet glaciation during Quaternary time reshaped the topography of the quadrangle, and approximately two-thirds of the map area is covered with Quaternary deposits related to the last glaciation. Geophysical studies and regional mapping indicate the Seattle fault lies north of Green Mountain. This fault produced a large earthquake about 1000 years ago and may pose a significant earthquake hazard (Bucknam and others, 1992; Atwater and Moore, 1992; Karlin and Abella,1992; Schuster and others, 1992; Jacoby and others, 1992). We found no evidence of Holocene faulting in the Wildcat Lake quadrangle. Geologic mapping within and marginal to the quadrangle began with Willis (1898), who described glacial deposits in Puget Sound. Weaver (1937) correlated volcanic rocks in the quadrangle to the Eocene Metchosin Volcanics on Vancouver Island. Sceva (1957), Garling and Moleenar (1965), and Deeter (1978) all focused on mapping and understanding the Quaternary stratigraphy of the Kitsap Peninsula, but they also examined bedrock in the quadrangle. Reeve (1979) was the first to examine the igneous rocks on Green and Gold Mountains in some detail, and Clark (1989) significantly improved Reeve's (1979) mapping. Clark's (1989) mapping was conducted soon after extensive logging on the mountains. A surficial geologic map of the Seattle 1:100,000-scale quadrangle, which includes the Wildcat Lake 1:24,000-scale quadrangle, was published by Yount and others (1993). Yount and Gower (1991) also published a bedrock geologic map of the Seattle quadrangle. Geologic mapping for this report was conducted by Haeussler in the spring and summer of 1998 and in the winter of 1999. We could not substantially improve upon the bedrock mapping of Clark (1989) and thus it is incorporated into this map. Well data in the southeastern corner of the map area also helped to constrain the surficial mapping (Geomatrix Consultants, 1997). In addition, 1995 vintage 1:12,000-scale aerial photographs were used in mapping Quaternary deposits. Geologic time scale is that of Berggeren and others (1995).

SILICATE TECHNOLOGY CORPORATION'S SOLIDIFICATION/ STABILIZATION TECHNOLOGY FOR ORGANIC AND INORGANIC CONTAMINANTS IN SOILS - APPLICATIONS ANALYSIS REPORT

EPA Science Inventory

This Applications Analysis Report evaluates the solidification/stabilization treatment process of Silicate Technology Corporation (STC) for the on-site treatment of hazardous waste. The STC immobilization technology utilizes a proprietary product (FMS Silicate) to chemically stab...

TECHNOLOGY EVALUATION REPORT: SILICATE TECHNOLOGY CORPORATION - SOLIDIFICATION/STABILIZATION OF PCP AND INORGANIC CONTAMINANTS IN SOILS - SELMA, CA

EPA Science Inventory

This Technolgy Evaluation Report evaluates the solidification/stabilization process of Silicate Technology Corporation (STC) for the on-site treatment of contaminated soil The STC immobilization technology uses a proprietary product (FMS Silicate) to chemically stabilize and ...

77 FR 21676 - Silicic Acid, Sodium Salt etc.; Tolerance Exemption

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-11

... Silicic acid, sodium salt, reaction products with chlorotrimethylsilane and iso-propyl alcohol, reaction..., reaction products with chlorotrimethylsilane and iso-propyl alcohol, reaction with poly(oxypropylene)-poly... from the requirement of a tolerance for residues of Silicic acid, sodium salt, reaction products with...

Metal/Silicate Partitioning of P, Ga, and W at High Pressures and Temperatures: Dependence on Silicate Melt Composition

NASA Technical Reports Server (NTRS)

Bailey, Edward; Drake, Michael J.

2004-01-01

The distinctive pattern of element concentrations in the upper mantle provides essential evidence in our attempts to understand the accretion and differentiation of the Earth (e.g., Drake and Righter, 2002; Jones and Drake, 1986; Righter et al., 1997; Wanke 1981). Core formation is best investigated through use of metal/silicate partition coefficients for siderophile elements. The variables influencing partition coefficients are temperature, pressure, the major element compositions of the silicate and metal phases, and oxygen fugacity. Examples of studies investigating the effects of these variables on partitioning behavior are: composition of the metal phase by Capobianco et al. (1999) and Righter et al. (1997); silicate melt composition by Watson (1976), Walter and Thibault (1995), Hillgren et al. (1996), Jana and Walker (1997), and Jaeger and Drake (2000); and oxygen fugacity by Capobianco et al. (1999), and Walter and Thibault (1995). Here we address the relative influences of silicate melt composition, pressure and temperature.

Heterogeneous Nucleation of Protein Crystals on Fluorinated Layered Silicate

PubMed Central

Ino, Keita; Udagawa, Itsumi; Iwabata, Kazuki; Takakusagi, Yoichi; Kubota, Munehiro; Kurosaka, Keiichi; Arai, Kazuhito; Seki, Yasutaka; Nogawa, Masaya; Tsunoda, Tatsuo; Mizukami, Fujio; Taguchi, Hayao; Sakaguchi, Kengo

2011-01-01

Here, we describe an improved system for protein crystallization based on heterogeneous nucleation using fluorinated layered silicate. In addition, we also investigated the mechanism of nucleation on the silicate surface. Crystallization of lysozyme using silicates with different chemical compositions indicated that fluorosilicates promoted nucleation whereas the silicates without fluorine did not. The use of synthesized saponites for lysozyme crystallization confirmed that the substitution of hydroxyl groups contained in the lamellae structure for fluorine atoms is responsible for the nucleation-inducing property of the nucleant. Crystallization of twelve proteins with a wide range of pI values revealed that the nucleation promoting effect of the saponites tended to increase with increased substitution rate. Furthermore, the saponite with the highest fluorine content promoted nucleation in all the test proteins regardless of their overall net charge. Adsorption experiments of proteins on the saponites confirmed that the density of adsorbed molecules increased according to the substitution rate, thereby explaining the heterogeneous nucleation on the silicate surface. PMID:21818343

Teaching contact metamorphism, isograds, and mixed-volatile reactions: A suite-based approach

NASA Astrophysics Data System (ADS)

Peck, W. H.

2003-12-01

An important goal of teaching Introductory Petrology is to demonstrate how different kinds of approaches are integrated in studying petrologic problems. Depending on the goals of the study data used can be from the field, hand-sample, microscope, electron beam instrument, or mass spectrometer. A suite of samples with a known geographical and geological context can help students in drawing connections between different petrologic approaches, as the `geologic story' of the samples becomes a unifying theme. For teaching a unit on calc-silicates I use a suite of siliceous dolomite samples collected from the Ubehebe contact aureole (Death Valley, NV) as well as published data (Roselle et al., 1997; 1999) in a linked series of laboratory exercises and problem sets. The geology of the contact aureole is introduced in a three-hour laboratory exercise, where students identify the appearance of tremolite, forsterite, and periclase/brucite and the disappearance of quartz as the intrusion is approached. A concurrent problem set uses simplified mineral assemblage maps from the aureole. In the problem set students delineate isograds and determine the balanced metamorphic reactions by which the metamorphic minerals formed. Lecture material during this unit focuses on the physical properties of fluids in the crust and the mineralogical evidence for fluid-flow (with an emphasis on mixed-volatile reactions and T-XCO2 diagrams). A concrete field example helps focus student attention on the interrelation of disparate approaches by which petrologic problems addressed. The Ubehebe suite then becomes a unifying theme throughout the course: the specimens or regional geology are used in subsequent laboratories and lectures when introducing concepts such as grain nucleation and growth, reaction overstepping, and replacement textures. A virtual field trip of the Alta aureole, UT (using field photographs, maps, and photomicrographs) concludes the unit. The geology of the Alta aureole is similar to that of Ubehebe, and the virtual field trip acts as a review that emphases the general usefulness of the approaches discussed.

Psyche: The Science of a Metal World

NASA Astrophysics Data System (ADS)

Elkins-Tanton, L. T.

2016-12-01

(16) Psyche is a large metallic asteroid orbiting in the outer main belt at 3 AU. Psyche's metal composition is indicated by high radar albedo, thermal inertia, and density. Models show that among the accretionary collisions early in the solar system, some destructive "hit and run" impacts could strip the silicate mantle from differentiated bodies. This is the leading hypothesis for Psyche's formation: it is a bare planetesimal core. It is the only one we can explore for substantial information about a metal core (other metallic asteroids are far smaller and not roughly spherical). If our observations indicate that it is not a core, Psyche may instead be highly reduced, primordial metal-rich materials that accreted closer to the Sun, and never melted. Psyche is also a Discovery-class mission, selected for a Step 2 concept study, to investigate this metal body. The Psyche investigation has three broad goals: Understand a previously unexplored building block of planet formation: iron cores. Look inside the terrestrial planets, including Earth, by directly examining the interior of a differentiated body, which otherwise could not be seen. Explore a new type of world. For the first time, examine a world made not of rock, ice, or gas, but of metal. We will meet our science objectives with three domestic high heritage instruments and radio science: Multispectral imagers with clear and seven color filters map surface morphology and reveal the distribution of residual mantle silicates. A gamma-ray and neutron spectrometer determines elemental composition, particularly the concentrations of iron, nickel, silicon, and potassium. Dual fluxgate magnetometers, in a gradiometer configuration, characterize the magnetic field. Radio science maps the gravity field sufficiently to differentiate among core-formation hypotheses. New models for magnetic dynamo generation and solidification of planetesimal cores make testable predictions for geophysical measurements, and lead as well to predictions about tectonics and surface compositions. In this presentation we will show how measurements from these flight instruments can confirm or disprove hypotheses for Psyche's formation and evolution.

Martian Surface Compositions and Spectral Unit Mapping From the Thermal Emission Imaging System

NASA Astrophysics Data System (ADS)

Bandfield, J. L.; Christensen, P. R.; Rogers, D.

2005-12-01

The Thermal Emission Imaging System (THEMIS) on board the Mars Odyssey spacecraft observes Mars at nine spectral intervals between 6 and 15 microns and at 100 meter spatial sampling. This spectral and spatial resolution allows for mapping of local spectral units and coarse compositional determination of a variety of rock-forming materials such as carbonates, sulfates, and silicates. A number of data processing and atmospheric correction techniques have been developed to ease and speed the interpretation of multispectral THEMIS infrared images. These products and techniques are in the process of being made publicly available via the THEMIS website and were used to produce the results presented here. Spectral variability at kilometer scales in THEMIS data is more common in the southern highlands than in the northern lowlands. Many of the spectral units are associated with a mobile surface layer such as dune fields and mantled dust. However, a number of spectral units appear to be directly tied to the local geologic rock units. These spectral units are commonly associated with crater walls, floors, and ejecta blankets. Other surface compositions are correlated with layered volcanic materials and knobby remnant terrains. Most of the spectral variability observed to date appears to be tied to a variation in silicate mineralogy. Olivine rich units that have been previously reported in Nili Fossae, Ares Valles, and the Valles Marineris region appear to be sparse but common in a number of regions in the southern highlands. Variations in silica content consistent with previously reported global surface units also appear to be present in THEMIS images, allowing for an examination of their local geologic context. Previously reported quartz and feldspar rich exposures in northern Syrtis Major appear more extensive in the region than previously reported. A coherent global and local picture of the mineralogy of the Martian surface is emerging from THEMIS measurements along with other orbital thermal and near infrared spectroscopy measurements from the Mars Express and Mars Global Surveyor spacecraft.

Space Weathering on Icy Satellites in the Outer Solar System

NASA Technical Reports Server (NTRS)

Clark, R. N.; Perlman, Z.; Pearson, N.; Cruikshank, D. P.

2014-01-01

Space weathering produces well-known optical effects in silicate minerals in the inner Solar System, for example, on the Moon. Space weathering from solar wind and UV (ultraviolet radiation) is expected to be significantly weaker in the outer Solar System simply because intensities are low. However, cosmic rays and micrometeoroid bombardment would be similar to first order. That, combined with the much higher volatility of icy surfaces means there is the potential for space weathering on icy outer Solar System surfaces to show optical effects. The Cassini spacecraft orbiting Saturn is providing evidence for space weathering on icy bodies. The Cassini Visible and Infrared Mapping Spectrometer (VIMS) instrument has spatially mapped satellite surfaces and the rings from 0.35-5 microns and the Ultraviolet Imaging Spectrograph (UVIS) instrument from 0.1 to 0.2 microns. These data have sampled a complex mixing space between H2O ice and non-ice components and they show some common spectral properties. Similarly, spectra of the icy Galilean satellites and satellites in the Uranian system have some commonality in spectral properties with those in the Saturn system. The UV absorber is spectrally similar on many surfaces. VIMS has identified CO2, H2 and trace organics in varying abundances on Saturn's satellites. We postulate that through the spatial relationships of some of these compounds that they are created and destroyed through space weathering effects. For example, the trapped H2 and CO2 observed by VIMS in regions with high concentrations of dark material may in part be space weathering products from the destruction of H2O and organic molecules. The dark material, particularly on Iapetus which has the highest concentration in the Saturn system, is well matched by space-weathered silicates in the .4 to 2.6 micron range, and the spectral shapes closely match those of the most mature lunar soils, another indicator of space weathered material.

Geological mapping of lunar highland crater Lalande: Topographic configuration, morphology and cratering process

NASA Astrophysics Data System (ADS)

Li, Bo; Ling, Zongcheng; Zhang, Jiang; Chen, Jian; Liu, ChangQing; Bi, Xiangyu

2018-02-01

Highland crater Lalande (4.45°S, 8.63°W; D = 23.4 km) is located on the PKT area of the lunar near side, southeast of the Mare Insularum. It is a complex crater in Copernican era and has three distinguishing features: high silicic anomaly, the highest Th abundance and special landforms on its floor. There are some low-relief bulges on the left of Lalande's floor with regular circle or ellipse shapes. They are ∼250-680 m wide and ∼30-91 m high with maximum flank slopes >20°. There are two possible scenarios for the formation of these low-relief bulges which are impact melt products or young silicic volcanic eruptions. We estimated the absolute model ages of the ejecta deposits, several melt ponds and the hummocky floor and determined the ratio of diameter and depth of the crater Lalande. In addition, we found some similar bugle features within other Copernican-aged craters and there were no volcanic source vents on Lalande's floor. Thus, we hypothesized that these low-relief bulges were most consistent with an origin of impact melts during the crater formation instead of small and young volcanic activities occurring on the floor. Based on Kaguya Terrain Camera (TC) ortho-mosaic and Digital Terrain Model (DTM) data produced by TC imagery in stereo, geological units and some linear features on the floor and wall of Lalande have been mapped. Eight geological units are organized by crater floor units: hummocky floor, central peak and low-relief bulges; and crater wall units: terraced walls, channeled and veneered walls, interior walls, mass wasting areas, blocky areas, and melt ponds. These geological units and linear features provided us a chance to understand some details of the cratering process and elevation differences on the floor. We proposed that subsidence due to melt cooling, late-stage wall collapse and rocks uplifted from beneath the surface could be the possible causes of the observed elevation differences on Lalande's floor.

Effects of Incorporating High-Volume Fly Ash into Tricalcium Silicate on the Degree of Silicate Polymerization and Aluminum Substitution for Silicon in Calcium Silicate Hydrate

DOE PAGES

Bae, Sungchul; Taylor, Rae; Kilcoyne, David; ...

2017-02-04

This study assesses the quantitative effects of incorporating high-volume fly ash (HVFA) into tricalcium silicate (C 3S) paste on the hydration, degree of silicate polymerization, and Al substitution for Si in calcium silicate hydrate (C–S–H). Thermogravimetric analysis and isothermal conduction calorimetry showed that, although the induction period of C 3S hydration was significantly extended, the degree of hydration of C 3S after the deceleration period increased due to HVFA incorporation. Synchrotron-sourced soft X-ray spectromicroscopy further showed that most of the C 3S in the C 3S-HVFA paste was fully hydrated after 28 days of hydration, while that in the puremore » C 3S paste was not. The chemical shifts of the Si K edge peaks in the near-edge X-ray fine structure of C–S–H in the C 3S-HVFA paste directly indicate that Al substitutes for Si in C–S–H and that the additional silicate provided by the HVFA induces an enhanced degree of silicate polymerization. This new spectromicroscopic approach, supplemented with 27Al and 29Si magic-angle spinning nuclear magnetic resonance spectroscopy and transmission electron microscopy, turned out to be a powerful characterization tool for studying a local atomic binding structure of C–S–H in C 3S-HVFA system and presented results consistent with previous literature.« less

Effects of Incorporating High-Volume Fly Ash into Tricalcium Silicate on the Degree of Silicate Polymerization and Aluminum Substitution for Silicon in Calcium Silicate Hydrate

PubMed Central

Bae, Sungchul; Taylor, Rae; Kilcoyne, David; Moon, Juhyuk; Monteiro, Paulo J. M.

2017-01-01

This study assesses the quantitative effects of incorporating high-volume fly ash (HVFA) into tricalcium silicate (C3S) paste on the hydration, degree of silicate polymerization, and Al substitution for Si in calcium silicate hydrate (C–S–H). Thermogravimetric analysis and isothermal conduction calorimetry showed that, although the induction period of C3S hydration was significantly extended, the degree of hydration of C3S after the deceleration period increased due to HVFA incorporation. Synchrotron-sourced soft X-ray spectromicroscopy further showed that most of the C3S in the C3S-HVFA paste was fully hydrated after 28 days of hydration, while that in the pure C3S paste was not. The chemical shifts of the Si K edge peaks in the near-edge X-ray fine structure of C–S–H in the C3S-HVFA paste directly indicate that Al substitutes for Si in C–S–H and that the additional silicate provided by the HVFA induces an enhanced degree of silicate polymerization. This new spectromicroscopic approach, supplemented with 27Al and 29Si magic-angle spinning nuclear magnetic resonance spectroscopy and transmission electron microscopy, turned out to be a powerful characterization tool for studying a local atomic binding structure of C–S–H in C3S-HVFA system and presented results consistent with previous literature. PMID:28772490

Effects of Incorporating High-Volume Fly Ash into Tricalcium Silicate on the Degree of Silicate Polymerization and Aluminum Substitution for Silicon in Calcium Silicate Hydrate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bae, Sungchul; Taylor, Rae; Kilcoyne, David

This study assesses the quantitative effects of incorporating high-volume fly ash (HVFA) into tricalcium silicate (C 3S) paste on the hydration, degree of silicate polymerization, and Al substitution for Si in calcium silicate hydrate (C–S–H). Thermogravimetric analysis and isothermal conduction calorimetry showed that, although the induction period of C 3S hydration was significantly extended, the degree of hydration of C 3S after the deceleration period increased due to HVFA incorporation. Synchrotron-sourced soft X-ray spectromicroscopy further showed that most of the C 3S in the C 3S-HVFA paste was fully hydrated after 28 days of hydration, while that in the puremore » C 3S paste was not. The chemical shifts of the Si K edge peaks in the near-edge X-ray fine structure of C–S–H in the C 3S-HVFA paste directly indicate that Al substitutes for Si in C–S–H and that the additional silicate provided by the HVFA induces an enhanced degree of silicate polymerization. This new spectromicroscopic approach, supplemented with 27Al and 29Si magic-angle spinning nuclear magnetic resonance spectroscopy and transmission electron microscopy, turned out to be a powerful characterization tool for studying a local atomic binding structure of C–S–H in C 3S-HVFA system and presented results consistent with previous literature.« less

Reconnaissance Geologic Map of the Hayfork 15' Quadrangle, Trinity County, California

USGS Publications Warehouse

Irwin, William P.

2010-01-01

The Hayfork 15' quadrangle is located just west of the Weaverville 15' quadrangle in the southern part of the Klamath Mountains geologic province of northern California. It spans parts of six generally north-northwest-trending tectonostratigraphic terranes that are, from east to west, the Eastern Klamath, Central Metamorphic, North Fork, Eastern Hayfork, Western Hayfork, and Rattlesnake Creek terranes. Remnants of a once-widespread postaccretionary overlap assemblage, the Cretaceous Great Valley sequence, crop out at three localities in the southern part of the Hayfork quadrangle. The Tertiary fluvial and lacustrine Weaverville Formation occupies a large, shallow, east-northeast-trending graben in the south half of the quadrangle. The small area of Eastern Klamath terrane is part of the Oregon Mountain outlier, which is more widely exposed to the east in the Weaverville 15' quadrangle. It was originally mapped as a thrust plate of Bragdon(?) Formation, but it is now thought by some to be part of an outlier of Yreka terrane that has been dislocated 60 km southward by the La Grange Fault. The Central Metamorphic terrane, which forms the footwall of the La Grange Fault, was formed by the eastward subduction of oceanic crustal basalt (the Salmon Hornblende Schist) and its overlying siliceous sediments with interbedded limestone (the Abrams Mica Schist) beneath the Eastern Klamath terrane. Rb-Sr analysis of the Abrams Mica Schist indicates a Middle Devonian metamorphic age of approximately 380 Ma, which probably represents the age of subduction. The North Fork terrane, which is faulted against the western boundary of the Central Metamorphic terrane, consists of the Permian(?) North Fork ophiolite and overlying broken formation and melange of Permian to Early Jurassic (Pliensbachian) marine metasedimentary and metavolcanic rocks. The ophiolite, which crops out along the western border of the terrane, is thrust westward over the Eastern Hayfork terrane. The Eastern Hayfork terrane is a broken formation and melange of volcanic and sedimentary rocks, including chert and blocks of amphibolite, limestone, and serpentinized ultramafic rocks. The chert contains radiolarians of Permian and Triassic ages, but none of clearly Jurassic age. In contrast, the cherts of the North Fork terrane contain Early and Middle Jurassic radiolarians in addition to those of Permian and Triassic ages; also, some limestones of the Eastern Hayfork terrane contain fossil faunas of Tethyan affinity, but those of the North Fork terrane do not. The Western Hayfork terrane is an andesitic volcanic arc that was accreted to the Eastern Hayfork terrane. It consists mainly of metavolcaniclastic andesitic agglomerate and tuff, as well as argillite and chert, and it includes the dioritic Ironside Mountain batholith, which intruded during Middle Jurassic time. Two large patches of Western Hayfork terrane mapped in the central part of the Eastern Hayfork terrane may be exposed through windows in the Eastern Hayfork terrane, although the structural relation is not clear. The Rattlesnake Creek terrane is a melange that occupies only a small area in the southwest corner of the Hayfork quadrangle; however, it is a major unit in the Hyampom 15' quadrangle to the west. It consists mainly of broken and sheared ophiolitic rocks of probable Permian or early Mesozoic age. The Cretaceous Great Valley sequence overlap assemblage here postdates the Early Cretaceous (approximately 136 Ma) emplacement of the Shasta Bally batholith, which is widely exposed to the east in the Weaverville 15' quadrangle. The Great Valley sequence once covered much of the southern Klamath Mountains; however, in the Hayfork quadrangle, only three small patches remain near its southern boundary. Weakly consolidated nonmarine sedimentary rocks of the Weaverville Formation of mid-Tertiary age, which contain abundant fossil plants, occupy a large, shallow, east-northeast-trending graben

21 CFR 182.2437 - Magnesium silicate.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Magnesium silicate. 182.2437 Section 182.2437 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Anticaking Agents § 182.2437 Magnesium silicate. (a) Product. Magnesium...

Natural Weathering Rates of Silicate Minerals

NASA Astrophysics Data System (ADS)

White, A. F.

2003-12-01

Silicates constitute more than 90% of the rocks exposed at Earth's land surface (Garrels and Mackenzie, 1971). Most primary minerals comprising these rocks are thermodynamically unstable at surface pressure/temperature conditions and are therefore susceptible to chemical weathering. Such weathering has long been of interest in the natural sciences. Hartt (1853) correctly attributed chemical weathering to "the efficacy of water containing carbonic acid in promoting the decomposition of igneous rocks." Antecedent to the recent interest in the role of vegetation on chemical weathering, Belt (1874) observed that the most intense weathering of rocks in tropical Nicaragua was confined to forested regions. He attributed this effect to "the percolation through rocks of rain water charged with a little acid from decomposing vegetation." Chamberlin (1899) proposed that the enhanced rates of chemical weathering associated with major mountain building episodes in Earth's history resulted in a drawdown of atmospheric CO2 that led to periods of global cooling. Many of the major characteristics of chemical weathering had been described when Merrill (1906) published the groundbreaking volume Rocks, Rock Weathering, and Soils.The major advances since that time, particularly during the last several decades, have centered on understanding the fundamental chemical, hydrologic, and biologic processes that control weathering and in establishing quantitative weathering rates. This research has been driven by the importance of chemical weathering to a number environmentally and economically important issues. Undoubtedly, the most significant aspect of chemical weathering is the breakdown of rocks to form soils, a process that makes life possible on the surface of the Earth. The availability of many soil macronutrients such as magnesium, calcium, potassium, and PO4 is directly related to the rate at which primary minerals weather. Often such nutrient balances are upset by anthropogenic activities. For example, Huntington et al. (2000) show that extensive timber harvesting in the southeastern forests of the United States, which are underlain by intensely weathered saprolites, produces net calcium exports that exceed inputs from weathering, thus creating a long-term regional problem in forest management.The role of chemical weathering has long been recognized in economic geology. Tropical bauxites, which account for most of world's aluminum ores, are typical examples of residual concentration of silicate rocks by chemical weathering over long time periods (Samma, 1986). Weathering of ultramafic silicates such as peridotites forms residual lateritic deposits that contain significant deposits of nickel and cobalt. Ores generated by chemical mobilization include uranium deposits that are produced by weathering of granitic rocks under oxic conditions and subsequent concentration by sorption and precipitation ( Misra, 2000).Over the last several decades, estimating rates of silicate weathering has become important in addressing new environmental issues. Acidification of soils, rivers, and lakes has become a major concern in many parts of North America and Europe. Areas at particular risk are uplands where silicate bedrock, resistant to chemical weathering, is overlain by thin organic-rich soils (Driscoll et al., 1989). Although atmospheric deposition is the most important factor in watershed acidification, land use practices, such as conifer reforestation, also create acidification problems ( Farley and Werritty, 1989). In such environments, silicate hydrolysis reactions are the principal buffer against acidification. As pointed out by Drever and Clow (1995), a reasonable environmental objective is to decrease the inputs of acidity such that they are equal to or less than the rate of neutralization by weathering in sensitive watersheds.The intensive interest in past and present global climate change has renewed efforts to understand quantitatively feedback mechanisms between climate and chemical weathering. On timescales longer than a million years, atmospheric CO2 levels have been primarily controlled by the balance between the rate of volcanic inputs from the Earth's interior and the rate of uptake through chemical weathering of silicates at the Earth's surface (Ruddiman, 1997). Weathering is proposed as the principal moderator in controlling large increases and decreases in global temperature and precipitation through the greenhouse effects of CO2 over geologic time (R. A. Berner and E. K. Berner, 1997). Weathering processes observed in paleosols, discussed elsewhere in this volume (see Chapter 5.18), have also been proposed as indicating changes in Archean atmospheric CO2 and O2 levels (Ohmoto, 1996; Rye and Holland, 1998).

Preliminary geologic map of the Al Jawf Quadrangle, sheet 29D, Kingdom of Saudi Arabia

USGS Publications Warehouse

Meissner, C.R.; Dini, S.M.; Farasani, A.M.; Riddler, G.P.; Van Eck, Marcel; Aspinall, N.C.

1989-01-01

Phosphorite, a commodity of major economic interest in the Sirhan-Turayf basin, is exposed in the map area along escarpments that form the southeastern rim of the basin. The grade of the phosphorite is as much as 21 percent P2O5, but the beds are thin and lenticular.    

Opportunities for Monitoring Io's Volcanic Activity in the Visible and Infrared From JUICE - It's All About (Eruption) Style

NASA Astrophysics Data System (ADS)

Davies, Ashley; Matson, D.; McEwen, A. S.; Keszthelyi, L.

2012-10-01

The ESA Jupiter Icy Moons Explorer (JUICE) provides many opportunities for long-range monitoring of Io’s extraordinary silicate volcanic activity [1, 2]. A considerable amount of valuable work can be performed even with relatively low-spatial-resolution observations [2]. Techniques developed from the study of Galileo NIMS data and observations of terrestrial silicate volcanism allow the identification of likely eruption style [2] at many locations where the entire eruption is sub-pixel. Good temporal coverage, especially for episodic eruptions (including high-energy “outburst” eruptions), is important for modelling purposes. With opportunities to observe Io on a regular basis (hours-days) during cruise/orbital reduction phases, a visible-to-near-infrared mapping spectrometer (covering 0.4-5.5 µm) is the best instrument to chart the magnitude and variability of Io’s volcanic activity, allowing comparison with an existing and constantly expanding set of Io observations [e.g. 1, 3]. The eruption temperature of Io’s dominant silicate lava, a constraint on interior composition and conditions, is a major unanswered question in the wake of the Galileo mission [1]. A careful approach to instrument design is needed to ensure that observations by both imager and IR spectrometer on JUICE are capable of determining lava eruption temperature [e.g., 4] in low spatial resolution data. With an ideal thermal target (e.g., outburst eruption; the proposed lava lake at Pele) the imager should obtain multi-spectral data in a rapid sequence to allow stability of the thermal source to be quantified. Observations by imager and spectrometer have to be contemporaneous and unsaturated. References: [1] Davies, A. (2007) “Volcanism on Io”, Cam. Univ. Press. [2] Davies et al. (2010) JVGR, 194, 75-99. [3] Veeder et al. (2012) Icarus, 219, 701-722. [4] Davies et al. (2011) GRL, 38, L21308. This work was performed at the Jet Propulsion Laboratory-California Institute of Technology, under NASA contract. AGD thanks the NASA OPR program for support.

Making an Iron Planet: The Case for Repeated Hit and Run Collisions

NASA Astrophysics Data System (ADS)

Asphaug, E. I.; Reufer, A.

2014-12-01

Earth, Venus, Mars and some of the largest asteroids have massive silicate mantles surrounding iron cores, and chondritic compositions. Against this backdrop are anomalies like the iron planet Mercury, and the Moon with almost no core, and metallic asteroids like Psyche. The Moon can be explained by giant impact, but for Mercury a giant impact (Benz et al., Icarus 1988) is problematic. Mercury must retain substantial volatiles after its obliteration (e.g. Peplowski et al., Science 2011), and must somehow avoid accreting its ejected silicates (Gladman and Coffey, MAPS 2009). SPH simulations have shown (Asphaug and Reufer, Nature Geosciences 2014; Sarid et al., LPSC 2014) that a differentiated chondritic proto-Mercury about 3 times its present mass can be stripped of its mantle in one energetic hit and run collision with a larger planet (proto-Venus or proto-Earth). To preserve Mercury's volatiles we also consider the scenario of lower energy hit and runs, in succession. We show that if 20 Mars-like planets accreted stochastically to form Venus and the Earth, then the statistics of attrition is likely to lead to one planet (Mercury) expressing repeated mantle stripping, and another planet (Mars) relatively undisturbed. For iron asteroids the "missing mantle paradox" likewise looms prominent. Where does it go, and how do we strip away so much mantle rock (in some cases down to a bare iron core; Yang et al., Nature 2007, Moskovitz et al., EPSL 2011) while leaving asteroids like Vesta presumably intact? According to the hit and run hypothesis, the sink for all this missing silicate is the larger accreted bodies at the top of the feeding chain, as they win the pairwise dynamical competition for stripped materials. This exotic origin of relics is only relevant to those few pairwise encounters that do not accrete both bodies. So the small survivors are lucky, and how they are lucky -- their attrition bias -- is manifested as compositional diversity and a preponderance of iron relics.

Dysbiosis of the Fecal Microbiota in Cattle Infected with Mycobacterium avium subsp. paratuberculosis

PubMed Central

Vecchiarelli, Bonnie; Indugu, Nagaraju; Kumar, Sanjay; Gallagher, Susan C.; Fyock, Terry L.; Sweeney, Raymond W.

2016-01-01

Johne's disease (JD) is a chronic, intestinal infection of cattle, caused by Mycobacterium avium subsp. paratuberculosis (MAP). It results in granulomatous inflammation of the intestinal lining, leading to malabsorption, diarrhea, and weight loss. Crohn’s disease (CD), a chronic, inflammatory gastrointestinal disease of humans, has many clinical and pathologic similarities to JD. Dysbiosis of the enteric microbiota has been demonstrated in CD patients. It is speculated that this dysbiosis may contribute to the intestinal inflammation observed in those patients. The purpose of this study was to investigate the diversity patterns of fecal bacterial populations in cattle infected with MAP, compared to those of uninfected control cattle, using phylogenomic analysis. Fecal samples were selected to include samples from 20 MAP-positive cows; 25 MAP-negative herdmates; and 25 MAP-negative cows from a MAP-free herd. The genomic DNA was extracted; PCR amplified sequenced on a 454 Roche platform, and analyzed using QIIME. Approximately 199,077 reads were analyzed from 70 bacterial communities (average of 2,843 reads/sample). The composition of bacterial communities differed between the 3 treatment groups (P < 0.001; Permanova test). Taxonomic assignment of the operational taxonomic units (OTUs) identified 17 bacterial phyla across all samples. Bacteroidetes and Firmicutes constituted more than 95% of the bacterial population in the negative and exposed groups. In the positive group, lineages of Actinobacteria and Proteobacteria increased and those of Bacteroidetes and Firmicutes decreased (P < 0.001). Actinobacteria was highly abundant (30% of the total bacteria) in the positive group compared to exposed and negative groups (0.1–0.2%). Notably, the genus Arthrobacter was found to predominate Actinobacteria in the positive group. This study indicates that MAP-infected cattle have a different composition of their fecal microbiota than MAP-negative cattle. PMID:27494144

Dysbiosis of the Fecal Microbiota in Cattle Infected with Mycobacterium avium subsp. paratuberculosis.

PubMed

Fecteau, Marie-Eve; Pitta, Dipti W; Vecchiarelli, Bonnie; Indugu, Nagaraju; Kumar, Sanjay; Gallagher, Susan C; Fyock, Terry L; Sweeney, Raymond W

2016-01-01

Johne's disease (JD) is a chronic, intestinal infection of cattle, caused by Mycobacterium avium subsp. paratuberculosis (MAP). It results in granulomatous inflammation of the intestinal lining, leading to malabsorption, diarrhea, and weight loss. Crohn's disease (CD), a chronic, inflammatory gastrointestinal disease of humans, has many clinical and pathologic similarities to JD. Dysbiosis of the enteric microbiota has been demonstrated in CD patients. It is speculated that this dysbiosis may contribute to the intestinal inflammation observed in those patients. The purpose of this study was to investigate the diversity patterns of fecal bacterial populations in cattle infected with MAP, compared to those of uninfected control cattle, using phylogenomic analysis. Fecal samples were selected to include samples from 20 MAP-positive cows; 25 MAP-negative herdmates; and 25 MAP-negative cows from a MAP-free herd. The genomic DNA was extracted; PCR amplified sequenced on a 454 Roche platform, and analyzed using QIIME. Approximately 199,077 reads were analyzed from 70 bacterial communities (average of 2,843 reads/sample). The composition of bacterial communities differed between the 3 treatment groups (P < 0.001; Permanova test). Taxonomic assignment of the operational taxonomic units (OTUs) identified 17 bacterial phyla across all samples. Bacteroidetes and Firmicutes constituted more than 95% of the bacterial population in the negative and exposed groups. In the positive group, lineages of Actinobacteria and Proteobacteria increased and those of Bacteroidetes and Firmicutes decreased (P < 0.001). Actinobacteria was highly abundant (30% of the total bacteria) in the positive group compared to exposed and negative groups (0.1-0.2%). Notably, the genus Arthrobacter was found to predominate Actinobacteria in the positive group. This study indicates that MAP-infected cattle have a different composition of their fecal microbiota than MAP-negative cattle.

Water chemistry at Snowshoe Mountain, Colorado: mixed processes in a common bedrock

USGS Publications Warehouse

Hoch, A.R.; Reddy, M.M.

2001-01-01

At Snowshoe Mountain the primary bedrock is quite homogeneous, but weathering processes vary as waters moves through the soils, vadose zone and phreatic zone of the subsurface. In the thin soil, physical degradation of tuff facilitates preferential dissolution of potassium ion from glass within the rock matrix, while other silicate minerals remain unaltered. In the vadose zone, in the upper few meters of fractured bedrock, dilute water infiltrates during spring snowmelt and summer storms, leading to preferential dissolution of augite exposed on fracture surfaces. Deeper yet, in the phreatic zone of the fractured bedrock, Pleistocene calcite fracture fillings dissolve, and dioctahedral and trioctahedral clays form as penetrative weathering alters feldspar and pyroxene. Alkalinity is generated and silica concentrations are buffered by mineral alteration reactions.

Geology of the Mid-Miocene Rooster Comb Caldera and Lake Owyhee Volcanic Field, eastern Oregon: Silicic volcanism associated with Grande Ronde flood basalt

NASA Astrophysics Data System (ADS)

Benson, Thomas R.; Mahood, Gail A.

2016-01-01

The Lake Owyhee Volcanic Field (LOVF) of eastern Oregon consists of rhyolitic caldera centers and lava fields contemporaneous with and spatially related to Mid-Miocene Columbia River flood basalt volcanism. Previous studies delineated two calderas in the southeastern part of LOVF near Owyhee Reservoir, the result of eruptions of two ignimbrites, the Tuff of Leslie Gulch and the Tuff of Spring Creek. Our new interpretation is that these two map units are differentially altered parts of a single ignimbrite produced in a major phreatomagmatic eruption at 15.8 Ma. Areas previously mapped as Tuff of Spring Creek are locations where the ignimbrite contains abundant clinoptilolite ± mordenite, which made it susceptible to erosion. The resistant intracaldera Tuff of Leslie Gulch has an alteration assemblage of albite ± quartz, indicative of low-temperature hydrothermal alteration. Our new mapping of caldera lake sediments and pre- and post-caldera rhyolitic lavas and intrusions that are chemically similar to intracaldera Tuff of Leslie Gulch point to a single 20 × 25 km caldera, which we name the Rooster Comb Caldera. Erosion of the resurgently uplifted southern half of the caldera created dramatic exposures of intracaldera Tuff of Leslie Gulch cut by post-caldera rhyolite dikes and intrusions that are the deeper-level equivalents of lava domes and flows that erupted into the caldera lake preserved in exposures to the northeast. The Rooster Comb Caldera has features in common with more southerly Mid-Miocene calderas of the McDermitt Volcanic Field and High Rock Caldera Complex, including formation in a basinal setting shortly after flood basalt eruptions ceased in the region, and forming on eruption of peralkaline ignimbrite. The volcanism at Rooster Comb Caldera postdates the main activity at McDermitt and High Rock, but, like it, begins 300 ky after flood basalt volcanism begins in the area, and while flood basalts don't erupt through the silicic focus, are contemporaneous with the latest stages of eruptions nearby. High Rock and McDermitt rhyolites are associated with propagation of Steens Basalt dikes to the south, and LOVF rhyolites with later propagation of Grande Ronde Basalt dikes to the north and north-northwest.

Granite Exfoliation, Cosumnes River Watershed, Somerset, California

NASA Astrophysics Data System (ADS)

Crockett, I. Q.; Neiss-Cortez, M.

2015-12-01

In the Sierra Nevada foothills of California there are many exposed granite plutons within the greater Sierra Nevada batholith. As with most exposed parts of the batholith, these granite slabs exfoliate. It is important to understand exfoliation for issues of public safety as it can cause rock slides near homes, roads, and recreation areas. Through observation, measuring, and mapping we characterize exfoliation in our Cosumnes River watershed community.

Geologic map of the Peach Springs 30' x 60' quadrangle, Mohave and Coconino counties, northwestern Arizona

USGS Publications Warehouse

Billingsley, George H.; Block, Debra L.; Dyer, Helen C.

2006-01-01

This map is a product of a cooperative project of the U.S. Geological Survey, the U.S. National Park Service, and the Bureau of Land Management to provide geologic map coverage and regional geologic information for visitor services and resource management of Grand Canyon National Park, Lake Mead National Recreation Area, Grand Canyon-Parashant-National Monument, and adjacent lands in northwestern Arizona. This map is a synthesis of previous and new geologic mapping that encompasses the Peach Springs 30' x 60' quadrangle, Arizona. The geologic data will support future geologic, biologic, hydrologic, and other science resource studies of this area conducted by the National Park Service, the Hualapai Indian Tribe, the Bureau of Land Management, the State of Arizona, and private organizations. The Colorado River and its tributaries have dissected the southwestern Colorado Plateau into what is now the southwestern part of Grand Canyon. The erosion of Grand Canyon has exposed about 426 m (1,400 ft) of Proterozoic crystalline metamorphic rocks and granite, about 1,450 m (4,760 ft) of Paleozoic strata, and about 300 m (1,000 ft) of Tertiary sedimentary rocks. Outcrops of Proterozoic crystalline rocks are exposed at the bottom of Grand Canyon at Granite Park from Colorado River Mile 207 to 209, at Mile 212, and in the Lower Granite Gorge from Colorado River Mile 216 to 262, and along the Grand Wash Cliffs in the southwest corner of the map area.

High Pressure Response of Siliceous Materials

DTIC Science & Technology

2013-02-01

iron-containing soda lime silicate glass, opal (a hydrated silicate glass), ROBAX glass ceramic, and others were single crystal (α-quartz) and...10 2.6. Opal (hydrated amorphous silica...Raman spectrum as a function of stress for opal (hydrated silica) glass. ................... 29 4.9. Raman spectrum as a function of stress for

The stripping of penetration 85-100 asphalt from silicate aggregate rocks : a laboratory study.

DOT National Transportation Integrated Search

1972-01-01

In Virginia stripping has occurred when certain of the acidic silicate rocks have been used as aggregate in bituminous paving. The purpose of this project was to discover which kinds of silicate aggregate would be most apt to remain well bonded in bi...

Microstructures of Rare Silicate Stardust from Nova and Supernovae

NASA Technical Reports Server (NTRS)

Nguyen, A. N.; Keller, L. P.; Rahman, Z.; Messenger, S

2011-01-01

Most silicate stardust analyzed in the laboratory and observed around stellar environments derives from O-rich red giant and AGB stars [1,2]. Supernova (SN) silicates and oxides are comparatively rare, and fewer than 10 grains from no-va or binary star systems have been identified to date. Very little is known about dust formation in these stellar environments. Mineralogical studies of only three O-rich SN [3-5] and no nova grains have been performed. Here we report the microstructure and chemical makeup of two SN silicates and one nova grain.

Sol-gel-derived double-layered nanocrystal memory

NASA Astrophysics Data System (ADS)

Ko, Fu-Hsiang; You, Hsin-Chiang; Lei, Tan-Fu

2006-12-01

The authors have used the sol-gel spin-coating method to fabricate a coexisting hafnium silicate and zirconium silicate double-layered nanocrystal (NC) memories. From transmission electron microscopic and x-ray photoelectron spectroscopic analyses, the authors determined that the hafnium silicate and zirconium silicate NCs formed after annealing at 900°C for 1min. When using channel hot electron injection for charging and band-to-band tunneling-induced hot hole injection for discharging, the NC memories exhibited superior Vth shifting because of the higher probability for trapping the charge carrier.

Silicate-catalyzed chemical grouting compositions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1972-09-28

Chemical grouting compositions for stabilizing earth, sand, and other porous particulate formations or agglomerates of solids are described. The composition for producing a chemically grouting structure consists of an aqueous base solution of: (1) vegetative polyphenolic material consisting of condensed type tannins, and an aqueous catalyst solution of (2) a water-soluble alkali metal silicate. The polyphenolic material is present in an amount from 5% to 40% based on the weight of the base solution, and the water- soluble alkali metal silicate is present in an amount to provide from 1% to 15% SiOD2U in the silicate compound based on themore » weight of the polyphenolic material. These grouting compositions are completely safe to operating personnel and to surrounding environment, since the potassium or sodium silicate catalysts are nontoxic. (15 claims)« less

Carbonation of metal silicates for long-term CO.sub.2 sequestration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blencoe, James G.; Palmer, Donald A.; Anovitz, Lawrence M.

In a preferred embodiment, the invention relates to a process of sequestering carbon dioxide. The process comprises the steps of: (a) reacting a metal silicate with a caustic alkali-metal hydroxide to produce a hydroxide of the metal formerly contained in the silicate; (b) reacting carbon dioxide with at least one of a caustic alkali-metal hydroxide and an alkali-metal silicate to produce at least one of an alkali-metal carbonate and an alkali-metal bicarbonate; and (c) reacting the metal hydroxide product of step (a) with at least one of the alkali-metal carbonate and the alkali-metal bicarbonate produced in step (b) to producemore » a carbonate of the metal formerly contained in the metal silicate of step (a).« less

Pumping Iron and Silica Bodybuilding

NASA Astrophysics Data System (ADS)

Mcnair, H.; Brzezinski, M. A.; Krause, J. W.; Parker, C.; Brown, M.; Coale, T.; Bruland, K. W.

2016-02-01

The availability of dissolved iron influences the stoichiometry of nutrient uptake by diatoms. Under nutrient replete conditions diatoms consume silicic acid and nitrate in a 1:1 ratio, this ratio increases under iron stress. Using the tracers 32Si and PDMPO, the total community and group-specific silica production rates were measured along a gradient of dissolved iron in an upwelling plume off the California coast. At each station, a control (ambient silicic acid) and +20 µM silicic acid treatment were conducted with each tracer to determine whether silicic acid limitation controlled the rate of silica production. Dissolved iron was 1.3 nmol kg-1 nearshore and decreased to 0.15 nmol kg-1 offshore. Silicic acid decreased more rapidly than nitrate, it was nearly 9 µM higher in the nearshore and 7 µM lower than nitrate in the middle of the transect where the iron concentration had decreased. The rate of diatom silica production decreased in tandem with silicic acid concentration, and silica production limitation by low silicic acid was most pronounced when iron concentrations were >0.4 nmol kg-1. The composition of the diatom assemblage shifted from Chaetoceros spp. dominated nearshore to a more sparse pennate-dominated assemblage offshore. Changes in taxa-specific silica production rates will be reported based on examination of PDMPO labeled cells using confocal microscopy.

A framework for predicting global silicate weathering and CO2 drawdown rates over geologic time-scales.

PubMed

Hilley, George E; Porder, Stephen

2008-11-04

Global silicate weathering drives long-time-scale fluctuations in atmospheric CO(2). While tectonics, climate, and rock-type influence silicate weathering, it is unclear how these factors combine to drive global rates. Here, we explore whether local erosion rates, GCM-derived dust fluxes, temperature, and water balance can capture global variation in silicate weathering. Our spatially explicit approach predicts 1.9-4.6 x 10(13) mols of Si weathered globally per year, within a factor of 4-10 of estimates of global silicate fluxes derived from riverine measurements. Similarly, our watershed-based estimates are within a factor of 4-18 (mean of 5.3) of the silica fluxes measured in the world's ten largest rivers. Eighty percent of total global silicate weathering product traveling as dissolved load occurs within a narrow range (0.01-0.5 mm/year) of erosion rates. Assuming each mol of Mg or Ca reacts with 1 mol of CO(2), 1.5-3.3 x 10(8) tons/year of CO(2) is consumed by silicate weathering, consistent with previously published estimates. Approximately 50% of this drawdown occurs in the world's active mountain belts, emphasizing the importance of tectonic regulation of global climate over geologic timescales.

Effect of Silicate Slag Application on Wheat Grown Under Two Nitrogen Rates

PubMed Central

White, Brandon; Tubana, Brenda S.; Babu, Tapasya; Mascagni, Henry; Agostinho, Flavia; Datnoff, Lawrence E.; Harrison, Steve

2017-01-01

Field studies were established on the alluvial floodplain soils in Louisiana, from 2013 to 2015, to evaluate the effect of silicate slag applications on productivity of wheat (Triticum aestivum), under sufficient and high nitrogen (N) application rates. Treatments were arranged in a randomized complete block design, with four replications consisting of twelve treatments: a factorial combination of two N (101 and 145 kg N ha−1) and five silicate slag rates (0, 1, 2, 4.5, and 9 Mg ha−1), and two control plots (with and without lime). Nitrogen had a greater impact on wheat productivity than silicate slag application. Wheat grain yield reached over 7000 kg ha−1 with applications of 145 kg N, and 9 Mg silicate slag per ha for soil having Si level <20 mg kg−1. Yield increases due to N or Si were attributed to the increase in number of spike m−2 and grain number spike−1. Silicate slag application effectively raised soil pH, and availability of several plant-essential nutrients, including plant-available N (nitrate, NO3−), demonstrating the benefits of slag application are beyond increasing plant-available Si. The benefits of silicate slag application were clearly observed in wheat supplied with high N, and on soil with low plant-available Si. PMID:29019922

Discovery of Ni-smectite-rich saprolite at Loma Ortega, Falcondo mining district (Dominican Republic): geochemistry and mineralogy of an unusual case of "hybrid hydrous Mg silicate - clay silicate" type Ni-laterite

NASA Astrophysics Data System (ADS)

Tauler, Esperança; Lewis, John F.; Villanova-de-Benavent, Cristina; Aiglsperger, Thomas; Proenza, Joaquín A.; Domènech, Cristina; Gallardo, Tamara; Longo, Francisco; Galí, Salvador

2017-10-01

Hydrous Mg silicate-type Ni-laterite deposits, like those in the Falcondo district, Dominican Republic, are dominated by Ni-enriched serpentine and garnierite. Recently, abundant Ni-smectite in the saprolite zone have been discovered in Loma Ortega, one of the nine Ni-laterite deposits in Falcondo. A first detailed study on these Ni-smectites has been performed (μXRD, SEM, EPMA), in addition to a geochemical and mineralogical characterisation of the Loma Ortega profile (XRF, ICP-MS, XRD). Unlike other smectite occurrences in laterite profiles worldwide, the Loma Ortega smectites are trioctahedral and exhibit high Ni contents never reported before. These Ni-smectites may be formed from weathering of pyroxene and olivine, and their composition can be explained by the mineralogy and the composition of the Al-depleted, olivine-rich parent ultramafic rock. Our study shows that Ni-laterites are mineralogically complex, and that a hydrous Mg silicate ore and a clay silicate ore can be confined to the same horizon in the weathering profile, which has significant implications from a recovery perspective. In accordance, the classification of "hybrid hydrous Mg silicate - clay silicate" type Ni-laterite deposit for Loma Ortega would be more appropriate.

Determination of Ground-Laboratory to In-Space Effective Atomic Oxygen Fluence for DC 93?500 Silicone

NASA Technical Reports Server (NTRS)

deGroh, Kim K.; Banks, Bruce A.; Ma, David

2004-01-01

The objective of this research was to calibrate the ground-to-space effective atomic oxygen fluence for DC 93-500 silicone in a thermal energy electron cyclotron resonance (ECR) oxygen plasma facility. Silicones, commonly used spacecraft materials, do not chemically erode with atomic oxygen attack like other organic materials but form an oxidized hardened silicate surface layer. Therefore, the effective atomic oxygen fluence in a ground test facility should not be determined based on mass loss measurements, as they are with organic polymers. A technique has been developed at the Glenn Research Center to determine the equivalent amount of atomic oxygen exposure in an ECR ground test facility to produce the same degree of atomic oxygen damage as in space. The approach used was to compare changes in the surface hardness of ground test (ECR) exposed DC 93-500 silicone with DC 93-500 exposed to low Earth orbit (LEO) atomic oxygen as part of a shuttle flight experiment. The ground to in-space effective atomic oxygen fluence correlation was determined based on the fluence in the ECR source that produced the same hardness for the fluence in-space. Nanomechanical hardness versus contact depth measurements were obtained for five ECR exposed DC 93-500 samples (ECR exposed for 18 to 40 hrs, corresponding to Kapton effective fluences of 4.2 x 10(exp 20) to 9.4 x 10(exp 20) atoms/sq cm, respectively) and for space exposed DC 93-500 from the Evaluation of Oxygen Interactions with Materials III (EOIM III) shuttle flight experiment, exposed to LEO atomic oxygen for 2.3 x 10(exp 20) atoms/sq cm. Pristine controls were also evaluated. A ground-to-space correlation value was determined based on correlation values for four contact depths (150, 200, 250, and 300 nm), which represent the near surface depth data. The results indicate that the Kapton effective atomic oxygen fluence in the ECR facility needs to be 2.64 times higher than in LEO to replicate equivalent exposure damage in the ground test silicone as occurred in the space exposed silicone.

Geologic map of the Vancouver and Orchards quadrangles and parts of the Portland and Mount Tabor quadrangles, Clark County, Washington, and Multnomah County, Oregon

USGS Publications Warehouse

O'Connor, Jim E.; Cannon, Charles M.; Mangano, Joseph F.; Evarts, Russell C.

2016-06-03

IntroductionThis is a 1:24,000-scale geologic map of the Vancouver and Orchards quadrangles and parts of the Portland and Mount Tabor quadrangles in the States of Washington and Oregon. The map area is within the Portland Basin and includes most of the city of Vancouver, Washington; parts of Clark County, Washington; and a small part of northwestern Multnomah County, Oregon. The Columbia River flows through the southern part of the map area, generally forming the southern limit of mapping. Mapped Quaternary geologic units include late Pleistocene cataclysmic flood deposits, eolian deposits, and alluvium of the Columbia River and its tributaries. Older deposits include Miocene to Pleistocene alluvium from an ancestral Columbia River. Regional geologic structures are not exposed in the map area but are inferred from nearby mapping.

[Bone cement adhesion on ceramic surfaces - surface activation of retention surfaces of knee prostheses by atmospheric plasma versus thermal surface treatment].

PubMed

Marx, B; Marx, R; Reisgen, U; Wirtz, D

2015-04-01

CoCrMo alloys are contraindicated for allergy sufferers. For these patients, uncemented and cemented prostheses made of titanium alloy are indicated. Knee prostheses machined from that alloy, however, may have poor tribological behaviour, especially in relation to UHMWPE inlays. Therefore, for knee replacement cemented high-strength oxide ceramic prostheses are suitable for allergy sufferers and in cases of particle-induced aseptic loosening. For adhesion of bone cement, the ceramic surface, however, only exposes inefficient mechanical retention spots as compared with a textured metal surface. Undercuts generated by corundum blasting which in the short-term are highly efficient on a CoCrMo surface are not possible on a ceramic surface due to the brittleness of ceramics. Textures due to blasting may initiate cracks which will weaken the strength of a ceramic prosthesis. Due to the lack of textures mechanical retention is poor or even not existent. Micromotions are promoted and early aseptic loosening is predictable. Instead silicoating of the ceramic surface will allow specific adhesion and result in better hydrolytic stability of bonding thereby preventing early aseptic loosening. Silicoating, however, presupposes a clean and chemically active surface which can be achieved by atmospheric plasma or thermal surface treatment. In order to evaluate the effectiveness of silicoating the bond strengths of atmospheric plasma versus thermal surface treated and silicate layered ZPTA surfaces were compared with "as-fired" surfaces by utilising TiAlV probes (diameter 6 mm) for traction-adhesive strength tests. After preparing samples for traction-adhesive strength tests (sequence: ceramic substrate, silicate and silane, protective lacquer [PolyMA], bone cement, TiAlV probe) they were aged for up to 150 days at 37 °C in Ringer's solution. The bond strengths observed for all ageing intervals were well above 20 MPa and much higher and more hydrolytically stable for silicate layered compared with "as-fired" ZPTA samples. Silicoating may be effective for achieving high initial bond strength of bone cement on surfaces of oxide ceramics and also suitable to stabilise bond strength under hydrolytic conditions as present in the human body in the long-term. Activation by atmospheric plasma or thermal surface treatment seems to be effective for activation prior to silicoating. Due the proposed silicate layer migration, micromotions and debonding should be widely reduced or even eliminated. Georg Thieme Verlag KG Stuttgart · New York.

Rapid thermal rejuvenation of high-crystallinity magma linked to porphyry copper deposit formation; evidence from the Koloula Porphyry Prospect, Solomon Islands

NASA Astrophysics Data System (ADS)

Tapster, S.; Condon, D. J.; Naden, J.; Noble, S. R.; Petterson, M. G.; Roberts, N. M. W.; Saunders, A. D.; Smith, D. J.

2016-05-01

Magmas containing the components needed to form porphyry copper deposits are relatively common within arcs, yet mineralising events are uncommon within the long-lived magmatic systems that host them. Understanding what causes the transition from barren to productive intrusions is critical to the development of conceptual deposit models. We have constrained the tempo of pre- and syn-mineralisation magmatic events in relationship to the thermal evolution of the plutonic body that underlies one of the world's youngest exposed plutonic-porphyry systems, the Inamumu Zoned Pluton, Koloula Porphyry Prospect, Solomon Islands. High precision ID-TIMS U-Pb dates of texturally and chemically characterised zircons indicate pluton emplacement over <150 kyr was superseded after ca. 50 kyr by two discrete episodes of mineralising porphyritic melt emplacement. Their associated hydrothermal systems initiated within ca. 30 kyrs of each other. Zircon populations within evolved intrusions contain resorbed cores that were recycled from the deeper magmatic system, yet their youngest dates are statistically indistinguishable from those yielded by crystals lacking resorption. Comparisons of Ti-in-zircon proxy temperatures, modelled zircon saturation temperatures and temperature-crystallinity relationships suggest that prior to being heated and emplaced within the shallow level pluton, magmas were stored at depth in a high-crystallinity (>50% crystals) state, past the point of rheological lock-up. We estimate that thermal rejuvenation of the deeper high-crystallinity magma and generation of a mobile melt fraction may have occurred ≤10 kyr before its transport and emplacement within the porphyry environment. The underlying pluton likely cooled and returned to high-crystallinity states prior to subsequent remobilisation-emplacement events. Titanium-in-zircon geothermometry and whole-rock geochemistry suggest pre-mineralisation intrusions were remobilised by mixing of a silicic magma with a high-temperature, less-evolved melt. In contrast, syn-mineralisation melts were most likely remobilised by the percolation of hot volatiles exsolved from contemporaneous less-evolved intrusions cooling beneath the crystalline silicic magma. The evidence for the rapid thermal rejuvenation and long term storage of highly crystalline silicic magmas is consistent with previous studies that indicate two components of exsolved volatiles contribute to ore forming fluids. We conclude that the liberation of crystal-rich porphyry copper deposit forming magmas, and the addition of the chemical components required for ore formation, are intrinsically linked to the volatiles released during the recharge of less-evolved melt into a highly crystalline silicic magma.

Infrared mapping resolves soft tissue preservation in 50 million year-old reptile skin.

PubMed

Edwards, N P; Barden, H E; van Dongen, B E; Manning, P L; Larson, P L; Bergmann, U; Sellers, W I; Wogelius, R A

2011-11-07

Non-destructive Fourier Transform InfraRed (FTIR) mapping of Eocene aged fossil reptile skin shows that biological control on the distribution of endogenous organic components within fossilized soft tissue can be resolved. Mapped organic functional units within this approximately 50 Myr old specimen from the Green River Formation (USA) include amide and sulphur compounds. These compounds are most probably derived from the original beta keratin present in the skin because fossil leaf- and other non-skin-derived organic matter from the same geological formation do not show intense amide or thiol absorption bands. Maps and spectra from the fossil are directly comparable to extant reptile skin. Furthermore, infrared results are corroborated by several additional quantitative methods including Synchrotron Rapid Scanning X-Ray Fluorescence (SRS-XRF) and Pyrolysis-Gas Chromatography/Mass Spectrometry (Py-GC/MS). All results combine to clearly show that the organic compound inventory of the fossil skin is different from the embedding sedimentary matrix and fossil plant material. A new taphonomic model involving ternary complexation between keratin-derived organic molecules, divalent trace metals and silicate surfaces is presented to explain the survival of the observed compounds. X-ray diffraction shows that suitable minerals for complex formation are present. Previously, this study would only have been possible with major destructive sampling. Non-destructive FTIR imaging methods are thus shown to be a valuable tool for understanding the taphonomy of high-fidelity preservation, and furthermore, may provide insight into the biochemistry of extinct organisms.

Infrared mapping resolves soft tissue preservation in 50 million year-old reptile skin

PubMed Central

Edwards, N. P.; Barden, H. E.; van Dongen, B. E.; Manning, P. L.; Larson, P. L.; Bergmann, U.; Sellers, W. I.; Wogelius, R. A.

2011-01-01

Non-destructive Fourier Transform InfraRed (FTIR) mapping of Eocene aged fossil reptile skin shows that biological control on the distribution of endogenous organic components within fossilized soft tissue can be resolved. Mapped organic functional units within this approximately 50 Myr old specimen from the Green River Formation (USA) include amide and sulphur compounds. These compounds are most probably derived from the original beta keratin present in the skin because fossil leaf- and other non-skin-derived organic matter from the same geological formation do not show intense amide or thiol absorption bands. Maps and spectra from the fossil are directly comparable to extant reptile skin. Furthermore, infrared results are corroborated by several additional quantitative methods including Synchrotron Rapid Scanning X-Ray Fluorescence (SRS-XRF) and Pyrolysis-Gas Chromatography/Mass Spectrometry (Py-GC/MS). All results combine to clearly show that the organic compound inventory of the fossil skin is different from the embedding sedimentary matrix and fossil plant material. A new taphonomic model involving ternary complexation between keratin-derived organic molecules, divalent trace metals and silicate surfaces is presented to explain the survival of the observed compounds. X-ray diffraction shows that suitable minerals for complex formation are present. Previously, this study would only have been possible with major destructive sampling. Non-destructive FTIR imaging methods are thus shown to be a valuable tool for understanding the taphonomy of high-fidelity preservation, and furthermore, may provide insight into the biochemistry of extinct organisms. PMID:21429928

Silicate and carbonate mineral weathering in soil profiles developed on Pleistocene glacial drift (Michigan, USA): Mass balances based on soil water geochemistry

NASA Astrophysics Data System (ADS)

Jin, Lixin; Williams, Erika L.; Szramek, Kathryn J.; Walter, Lynn M.; Hamilton, Stephen K.

2008-02-01

Geochemistry of soil, soil water, and soil gas was characterized in representative soil profiles of three Michigan watersheds. Because of differences in source regions, parent materials in the Upper Peninsula of Michigan (the Tahquamenon watershed) contain only silicates, while those in the Lower Peninsula (the Cheboygan and the Huron watersheds) have significant mixtures of silicate and carbonate minerals. These differences in soil mineralogy and climate conditions permit us to examine controls on carbonate and silicate mineral weathering rates and to better define the importance of silicate versus carbonate dissolution in the early stage of soil-water cation acquisition. Soil waters of the Tahquamenon watershed are the most dilute; solutes reflect amphibole and plagioclase dissolution along with significant contributions from atmospheric precipitation sources. Soil waters in the Cheboygan and the Huron watersheds begin their evolution as relatively dilute solutions dominated by silicate weathering in shallow carbonate-free soil horizons. Here, silicate dissolution is rapid and reaction rates dominantly are controlled by mineral abundances. In the deeper soil horizons, silicate dissolution slows down and soil-water chemistry is dominated by calcite and dolomite weathering, where solutions reach equilibrium with carbonate minerals within the soil profile. Thus, carbonate weathering intensities are dominantly controlled by annual precipitation, temperature and soil pCO 2. Results of a conceptual model support these field observations, implying that dolomite and calcite are dissolving at a similar rate, and further dissolution of more soluble dolomite after calcite equilibrium produces higher dissolved inorganic carbon concentrations and a Mg 2+/Ca 2+ ratio of 0.4. Mass balance calculations show that overall, silicate minerals and atmospheric inputs generally contribute <10% of Ca 2+ and Mg 2+ in natural waters. Dolomite dissolution appears to be a major process, rivaling calcite dissolution as a control on divalent cation and inorganic carbon contents of soil waters. Furthermore, the fraction of Mg 2+ derived from silicate mineral weathering is much smaller than most of the values previously estimated from riverine chemistry.

The influence of oxalate-promoted growth of saponite and talc crystals

USGS Publications Warehouse

Schumann, Dirk; Hartman, Hyman; Eberl, Dennis D.; Sears, S. Kelly; Hesse, Reinhard; Vali, Hojatollah

2013-01-01

The intercalating growth of new silicate layers or metal hydroxide layers in the interlayer space of other clay minerals is known from various mixed-layer clay minerals such as illite-smectite (I-S), chlorite-vermiculite, and mica-vermiculite. In a recent study, the present authors proposed that smectite-group minerals can be synthesized from solution as new 2:1 silicate layers within the low-charge interlayers of rectorite. That study showed how oxalate catalyzes the crystallization of saponite from a silicate gel at low temperatures (60ºC) and ambient pressure. As an extension of this work the aim of the present study was to test the claim that new 2:1 silicate layers can be synthesized as new intercalating layers in the low-charge interlayers of rectorite and whether oxalate could promote such an intercalation synthesis. Two experiments were conducted at 60ºC and atmospheric pressure. First, disodium oxalate solution was added to a suspension of rectorite in order to investigate the effects that oxalate anions have on the structure of rectorite. In a second experiment, silicate gel of saponitic composition (calculated interlayer charge −0.33 eq/O10(OH)2) was mixed with a suspension of rectorite and incubated in disodium oxalate solution. The synthesis products were extracted after 3 months and analyzed by X-ray diffraction and high-resolution transmission electron microscopy (HRTEM). The treatment of ultrathin sections with octadecylammonium (nC = 18) cations revealed the presence of 2:1 layer silicates with different interlayer charges that grew from the silicate gel. The oxalate-promoted nucleation of saponite and talc crystallites on the rectorite led to the alteration and ultimately to the destruction of the rectorite structure. The change was documented in HRTEM lattice-fringe images. The crystallization of new 2:1 layer silicates also occurred within the expandable interlayers of rectorite but not as new 2:1 silicate layers parallel to the previous 2:1 silicate layers. Instead, they grew independently of any orientation predetermined by the rectorite crystal substrate and their crystallization was responsible for the destruction of the rectorite structure.

On the metallicity dependence of crystalline silicates in oxygen-rich asymptotic giant branch stars and red supergiants

NASA Astrophysics Data System (ADS)

Jones, O. C.; Kemper, F.; Sargent, B. A.; McDonald, I.; Gielen, C.; Woods, Paul M.; Sloan, G. C.; Boyer, M. L.; Zijlstra, A. A.; Clayton, G. C.; Kraemer, K. E.; Srinivasan, S.; Ruffle, P. M. E.

2012-12-01

We investigate the occurrence of crystalline silicates in oxygen-rich evolved stars across a range of metallicities and mass-loss rates. It has been suggested that the crystalline silicate feature strength increases with increasing mass-loss rate, implying a correlation between lattice structure and wind density. To test this, we analyse Spitzer Infrared Spectrograph and Infrared Space Observatory Short Wavelength Spectrometer spectra of 217 oxygen-rich asymptotic giant branch and 98 red supergiants in the Milky Way, the Large and Small Magellanic Clouds, and Galactic globular clusters. These encompass a range of spectral morphologies from the spectrally rich which exhibit a wealth of crystalline and amorphous silicate features to 'naked' (dust-free) stars. We combine spectroscopic and photometric observations with the GRAMS grid of radiative transfer models to derive (dust) mass-loss rates and temperature. We then measure the strength of the crystalline silicate bands at 23, 28 and 33 μm. We detect crystalline silicates in stars with dust mass-loss rates which span over 3 dex, down to rates of ˜10-9 M⊙ yr-1. Detections of crystalline silicates are more prevalent in higher mass-loss rate objects, though the highest mass-loss rate objects do not show the 23-μm feature, possibly due to the low temperature of the forsterite grains or it may indicate that the 23-μm band is going into absorption due to high column density. Furthermore, we detect a change in the crystalline silicate mineralogy with metallicity, with enstatite seen increasingly at low metallicity.

Studies on aerosols. I. Reduction of dust deposition in lungs of rabbits by aqueous aerosols

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dautrebande, L.; Highman, B.; Alford, W.C.

1948-01-01

Rabbits were exposed to air containing 0.01 to 0.04 mg/liter zinc silicate dust with a mean diameter of 0.9 ..mu..m. Irregular breathing with some cyanosis after 2 hr was observed. Pulmonary changes after 4.5 to 5 hr included bronchitis, patchy atelectasis, emphysema, interstitial pneumonitis (thickening of septa, moderate congestion, infiltration of mononuclear cells and polymorphonuclear leukocytes). After 1, 7, or 14 days recovery there were no or only slight pulmonary problems. There was localization of particles at surfaces facing, deflecting or slowing air currents, particularly near pleura and hilus and less in central portion of lobes. Rabbits exposed to abovemore » dust plus aqueous wetting agent aerosol averaging 0.5 ..mu..m in diameter showed no cyanosis or marked respiratory difficulty. Rabbits showed less of above pulmonary changes and lesser amount of dust in lungs, particularly in alveoli and alveolar ducts. Most particles were cleared in 1 day in both groups, especially aerosol group, and essentially were all gone after 7 days. Differences were primarily due to coating of particles with liquid (increased size) and aggregation.« less

Photoemission Experiments for Charge Characteristics of Individual Dust Grains

NASA Technical Reports Server (NTRS)

Abbas, M. M.; Spann, James F., Jr.; Craven, Paul D.; West, E.; Pratico, Jared; Scheianu, D.; Tankosic, D.; Venturini, C. C.; Whitaker, Ann F. (Technical Monitor)

2001-01-01

Photoemission experiments with UV radiation have been performed to investigate the microphysics and charge characteristics of individual isolated dust grains of various compositions and sizes by using the electrodynamic balance facility at NASA Marshall Space Flight Center. Dust particles of 1 - 100 micrometer diameter are levitated in a vacuum chamber at pressures approx. 10(exp -5) torr and exposed to a collimated beam of UV radiation in the 120-300 nanometers spectral range from a deuterium lamp source with a MgF2 window. A monochromator is used to select the UV radiation wavelength with a spectral resolution of 8 nanometers. The electrodynamic facility permits measurements of the charge and diameters of particles of known composition, and monitoring of photoemission rates with the incident UV radiation. Experiments have been conducted on Al2O3 and silicate particles, and in particular on JSC-1 Mars regolith simulants, to determine the photoelectron yields and surface equilibrium potentials of dust particles when exposed to UV radiation in the 120-250 micrometers spectral range. A brief discussion of the experimental procedure, the results of photoemission experiments, and comparisons with theoretical models will be presented.

Synchrotron x-ray spectroscopy of EuHN O3 aqueous solutions at high temperatures and pressures and Nb-bearing silicate melt phases coexisting with hydrothermal fluids using a modified hydrothermal diamond anvil cell and rail assembly

USGS Publications Warehouse

Mayanovic, Robert A.; Anderson, Alan J.; Bassett, William A.; Chou, I.-Ming

2007-01-01

A modified hydrothermal diamond anvil cell (HDAC) rail assembly has been constructed for making synchrotron x-ray absorption spectroscopy, x-ray fluorescence, and x-ray mapping measurements on fluids or solid phases in contact with hydrothermal fluids up to ???900??C and 700 MPa. The diamond anvils of the HDAC are modified by laser milling grooves or holes, for the reduction of attenuation of incident and fluorescent x rays and sample cavities. The modified HDAC rail assembly has flexibility in design for measurement of light elements at low concentrations or heavy elements at trace levels in the sample and the capability to probe minute individual phases of a multiphase fluid-based system using focused x-ray microbeam. The supporting rail allows for uniform translation of the HDAC, rotation and tilt stages, and a focusing mirror, which is used to illuminate the sample for visual observation using a microscope, relative to the direction of the incident x-ray beam. A structure study of Eu(III) aqua ion behavior in high-temperature aqueous solutions and a study of Nb partitioning and coordination in a silicate melt in contact with a hydrothermal fluid are described as applications utilizing the modified HDAC rail assembly. ?? 2007 American Institute of Physics.

CMAS-Resistant Plasma Sprayed Thermal Barrier Coatings Based on Y2O3-Stabilized ZrO2 with Al3+ and Ti4+ Solute Additions

NASA Astrophysics Data System (ADS)

Senturk, Bilge S.; Garces, Hector F.; Ortiz, Angel L.; Dwivedi, Gopal; Sampath, Sanjay; Padture, Nitin P.

2014-04-01

The higher operating temperatures in gas-turbine engines made possible by thermal barrier coatings (TBCs) are engendering a new problem: environmentally ingested airborne silicate particles (sand, ash) melt on the hot TBC surfaces and form calcium-magnesium-alumino-silicate (CMAS) glass deposits. The molten CMAS glass degrades the TBCs, leading to their premature failure. Here, we demonstrate the use of a commercially manufactured feedstock powder, in conjunction with air plasma spray process, to deposit CMAS-resistant yttria-stabilized zirconia-based TBCs containing Al3+ and Ti4+ in solid solution. Results from the characterization of these new TBCs and CMAS/TBCs interaction experiments are presented. The CMAS mitigation mechanisms in these new TBCs involve the crystallization of the anorthite phase. Raman microscopy is used to generate large area maps of the anorthite phase in the CMAS-interacted TBCs demonstrating the potential usefulness of this method for studying CMAS/TBCs interactions. The ubiquity of airborne sand/ash particles and the ever-increasing demand for higher operating temperatures in future high efficiency gas-turbine engines will necessitate CMAS resistance in all hot-section components of those engines. In this context, the versatility, ease of processing, and low cost offered by the process demonstrated here could benefit the development of these new CMAS-resistant TBCs.

Intrinsic Size Effect in Scaffolded Porous Calcium Silicate Particles and Mechanical Behavior of Their Self-Assembled Ensembles.

PubMed

Hwang, Sung Hoon; Shahsavari, Rouzbeh

2018-01-10

Scaffolded porous submicron particles with well-defined diameter, shape, and pore size have profound impacts on drug delivery, bone-tissue replacement, catalysis, sensors, photonic crystals, and self-healing materials. However, understanding the interplay between pore size, particle size, and mechanical properties of such ultrafine particles, especially at the level of individual particles and their ensemble states, is a challenge. Herein, we focus on porous calcium-silicate submicron particles with various diameters-as a model system-and perform extensive 900+ nanoindentations to completely map out their mechanical properties at three distinct structural forms from individual submicron particles to self-assembled ensembles to pressure-induced assembled arrays. Our results demonstrate a notable "intrinsic size effect" for individual porous submicron particles around ∼200-500 nm, induced by the ratio of particle characteristic diameter to pore characteristic size distribution. Increasing this ratio results in a brittle-to-ductile transition where the toughness of the submicron particles increases by 120%. This size effect becomes negligible as the porous particles form superstructures. Nevertheless, the self-assembled arrays collectively exhibit increasing elastic modulus as a function of applied forces, while pressure-induced compacted arrays exhibit no size effect. This study will impact tuning properties of individual scaffolded porous particles and can have implications on self-assembled superstructures exploiting porosity and particle size to impart new functionalities.

Bloom - Microbial Bebop

DOE Office of Scientific and Technical Information (OSTI.GOV)

Larsen, Peter

2012-10-01

This musical composition was created from data of microbes (bacteria, algae and other microorganisms) sampled in the English Channel. Argonne National Laboratory biologist Peter Larsen created the songs as a unique way to present and comprehend large datasets. This composition highlights seasonal patterns in marine physical parameters at the L4 Station. The chords are generated from seasonal changes in photosynthetically active radiation. The melody of each measure is comprised of eight notes, each mapped to a physical environmental parameter, in the following order: temperature, soluble reactive phosphate, nitrate, nitrite, saline, silicate and chlorophyll A concentrations. More information at http://www.anl.gov/articles/songs-key... Photomore » of cyanobacteria colonies is courtesy Specious Reasons (http://www.flickr.com/photos/28594931...) at Flickr via Creative Commons.« less

High Pressure Response of Siliceous Materials

DTIC Science & Technology

2013-02-01

quartz, Starphire soda lime silicate glass, hydrated Starphire, BOROFLOAT borosilicate glass, an iron-containing soda lime silicate glass, opal (a hydrated... Opal (hydrated amorphous silica). .............................................................................. 10 2.7. ROBAX glass ceramic...spectrum as a function of stress for BOROFLOAT borosilicate glass. .......... 29 4.8. Raman spectrum as a function of stress for opal (hydrated

Standards for electron probe microanalysis of silicates prepared by convenient method

NASA Technical Reports Server (NTRS)

Walter, L. S.

1966-01-01

Standard compositions suitable for electron probe microanalysis of various silicates are prepared by coprecipitation of specified salts with colloidal silica to form a gel which is decomposed into a powdered oxide mixture and compressed into thin pellets. These pellets of predetermined standard are compared with a silicate sample to determine its composition.

Geochemical and lithological factors in acid precipitation

Treesearch

James R. Kramer

1976-01-01

Acid precipitation is altered by interaction with rocks, sediment and soil. A calcareous region buffers even the most intense loading at pH ~8; an alumino silicate region with unconsolidated sediment buffers acid loadings at pH ~6.5; alumino silicate outcrops are generally acidified. Either FeOOH or alumino silicates are probable H+...

Continental erosion and the Cenozoic rise of marine diatoms

NASA Astrophysics Data System (ADS)

Cermeño, Pedro; Falkowski, Paul G.; Romero, Oscar E.; Schaller, Morgan F.; Vallina, Sergio M.

2015-04-01

Marine diatoms are silica-precipitating microalgae that account for over half of organic carbon burial in marine sediments and thus they play a key role in the global carbon cycle. Their evolutionary expansion during the Cenozoic era (66 Ma to present) has been associated with a superior competitive ability for silicic acid relative to other siliceous plankton such as radiolarians, which evolved by reducing the weight of their silica test. Here we use a mathematical model in which diatoms and radiolarians compete for silicic acid to show that the observed reduction in the weight of radiolarian tests is insufficient to explain the rise of diatoms. Using the lithium isotope record of seawater as a proxy of silicate rock weathering and erosion, we calculate changes in the input flux of silicic acid to the oceans. Our results indicate that the long-term massive erosion of continental silicates was critical to the subsequent success of diatoms in marine ecosystems over the last 40 My and suggest an increase in the strength and efficiency of the oceanic biological pump over this period.

Effect of silicate module of water glass on rheological parameters of poly(sodium acrylate)/sodium silicate hydrogels

NASA Astrophysics Data System (ADS)

Mastalska-Popiawska, J.; Izak, P.

2017-01-01

The poly(sodium acrylate)/sodium silicate hydrogels were synthesized in the presence of sodium thiosulphate and potassium persulphate as the redox initiators and N,N’-methylene-bisacrylamide as the cross-linking monomer. 20 wt% aqueous solution of sodium acrylate was polymerized together with water glass with different silicate modules (M) from 1.74 to 2.29, in three mass ratio of the monomer solution to the water glass 2:1, 1:1 and 1:2. Such obtained hybrid composites were rheologically tested using the oscillation method. It allowed to designate the crossover point during polymerization, as well as to define the viscoelastic properties of the casted hydrogel samples one week after the reaction. The obtained results of the oscillation measurements showed that cross-linking reaction proceeds very quickly and the lower the silicate module is, the process starts faster. After the completion of the reaction the silicate-polymer hydrogels are strongly elastic materials and the highest elasticity characterizes systems with the mass ratio 1:2, i.e. with the highest water glass content.

Synthesis, characterization and modelling of zinc and silicate co-substituted hydroxyapatite

PubMed Central

Friederichs, Robert J.; Chappell, Helen F.; Shepherd, David V.; Best, Serena M.

2015-01-01

Experimental chemistry and atomic modelling studies were performed here to investigate a novel ionic co-substitution in hydroxyapatite (HA). Zinc, silicate co-substituted HA (ZnSiHA) remained phase pure after heating to 1100°C with Zn and Si amounts of 0.6 wt% and 1.2 wt%, respectively. Unique lattice expansions in ZnSiHA, silicate Fourier transform infrared peaks and changes to the hydroxyl IR stretching region suggested Zn and silicate co-substitution in ZnSiHA. Zn and silicate insertion into HA was modelled using density functional theory (DFT). Different scenarios were considered where Zn substituted for different calcium sites or at a 2b site along the c-axis, which was suspected in singly substituted ZnHA. The most energetically favourable site in ZnSiHA was Zn positioned at a previously unreported interstitial site just off the c-axis near a silicate tetrahedron sitting on a phosphate site. A combination of experimental chemistry and DFT modelling provided insight into these complex co-substituted calcium phosphates that could find biomedical application as a synthetic bone mineral substitute. PMID:26040597

Continental erosion and the Cenozoic rise of marine diatoms

PubMed Central

Cermeño, Pedro; Falkowski, Paul G.; Romero, Oscar E.; Schaller, Morgan F.; Vallina, Sergio M.

2015-01-01

Marine diatoms are silica-precipitating microalgae that account for over half of organic carbon burial in marine sediments and thus they play a key role in the global carbon cycle. Their evolutionary expansion during the Cenozoic era (66 Ma to present) has been associated with a superior competitive ability for silicic acid relative to other siliceous plankton such as radiolarians, which evolved by reducing the weight of their silica test. Here we use a mathematical model in which diatoms and radiolarians compete for silicic acid to show that the observed reduction in the weight of radiolarian tests is insufficient to explain the rise of diatoms. Using the lithium isotope record of seawater as a proxy of silicate rock weathering and erosion, we calculate changes in the input flux of silicic acid to the oceans. Our results indicate that the long-term massive erosion of continental silicates was critical to the subsequent success of diatoms in marine ecosystems over the last 40 My and suggest an increase in the strength and efficiency of the oceanic biological pump over this period. PMID:25831504

Continental erosion and the Cenozoic rise of marine diatoms.

PubMed

Cermeño, Pedro; Falkowski, Paul G; Romero, Oscar E; Schaller, Morgan F; Vallina, Sergio M

2015-04-07

Marine diatoms are silica-precipitating microalgae that account for over half of organic carbon burial in marine sediments and thus they play a key role in the global carbon cycle. Their evolutionary expansion during the Cenozoic era (66 Ma to present) has been associated with a superior competitive ability for silicic acid relative to other siliceous plankton such as radiolarians, which evolved by reducing the weight of their silica test. Here we use a mathematical model in which diatoms and radiolarians compete for silicic acid to show that the observed reduction in the weight of radiolarian tests is insufficient to explain the rise of diatoms. Using the lithium isotope record of seawater as a proxy of silicate rock weathering and erosion, we calculate changes in the input flux of silicic acid to the oceans. Our results indicate that the long-term massive erosion of continental silicates was critical to the subsequent success of diatoms in marine ecosystems over the last 40 My and suggest an increase in the strength and efficiency of the oceanic biological pump over this period.

Silicate Crystal Formation in the Disk of an Erupting Star Artist Concept

NASA Image and Video Library

2009-05-13

This artist's concept illustrates how silicate crystals like those found in comets can be created by an outburst from a growing star. The image shows a young sun-like star encircled by its planet-forming disk of gas and dust. The silicate that makes up most of the dust would have begun as non-crystallized, amorphous particles. Streams of material are seen spiraling from the disk onto the star increasing its mass and causing the star to brighten and heat up dramatically. The outburst causes temperatures to rise in the star's surrounding disk. The animation (figure 1) zooms into the disk to show close-ups of silicate particles. When the disk warms from the star's outburst, the amorphous particles of silicate melt. As they cool off, they transform into forsterite (figure 2), a type of silicate crystal often found in comets in our solar system. In April 2008, NASA's Spitzer Space Telescope detected evidence of this process taking place on the disk of a young sun-like star called EX Lupi. http://photojournal.jpl.nasa.gov/catalog/PIA12008

A novel multifunctional pharmaceutical excipient: modification of the permeability of starch by processing with magnesium silicate.

PubMed

Rashid, Iyad; Al-Remawi, Mayyas; Leharne, Stephen A; Chowdhry, Babur Z; Badwan, Adnan

2011-06-15

A directly compressible excipient has been developed by co-processing starch with magnesium silicate. The foregoing was achieved either by co-precipitation of magnesium silicate onto different types of starch or by dry granulation of maize starch with magnesium silicate. A variety of techniques (permeability, water retention/swelling, compression analysis, scanning electron microscopy, tensile strength and disintegration/dissolution studies) were used to characterize these systems. The permeability of the formulations produced using the two methods was evaluated experimentally using Darcy's permeability law. Magnesium silicate, as an anti-adhering agent, increases the permeability of both maize and partially pregelatinized starch, resulting in compacts of high mechanical strength, short disintegration time and low lubricant sensitivity. Such advantages are evident when the properties of the physical mixture of maize starch with magnesium silicate are compared with the co-precipitation and dry granulation techniques. Formulation with this novel excipient system, using paracetamol as a model drug, indicated its suitability as a single multifunctional excipient. Copyright © 2011 Elsevier B.V. All rights reserved.

A mid-Permian chert event: widespread deposition of biogenic siliceous sediments in coastal, island arc and oceanic basins

USGS Publications Warehouse

Murchey, B.L.; Jones, D.L.

1992-01-01

Radiolarian and conodont of Permian siliceous rocks from twenty-three areas in teh the circum-Pacific and Mediterranean regions reveal a widespread Permian Chert Event during the middle Leonardian to Wordian. Radiolarian- and (or) sponge spicule-rich siliceous sediments accumulated beneath high productivity zones in coastal, island arc and oceanic basins. Most of these deposits now crop out in fault-bounded accreted terranes. Biogenic siliceous sediments did not accumulate in terranes lying beneath infertile waters including the marine sequences in terranes of northern and central Alaska. The Permian Chert Event is coeval with major phosphorite deposition along the western margin of Pangea (Phosphoria Formation and related deposits). A well-known analogue for this event is middle Miocene deposition of biogenic siliceous sediments beneath high productivity zones in many parts of the Pacific and concurrent deposition of phosphatic as well as siliceous sediments in basins along the coast of California. Interrelated factors associated with both the Miocene and Permian depositional events include plate reorientations, small sea-level rises and cool polar waters. ?? 1992.

Q-Speciation and Network Structure Evolution in Invert Calcium Silicate Glasses.

PubMed

Kaseman, Derrick C; Retsinas, A; Kalampounias, A G; Papatheodorou, G N; Sen, S

2015-07-02

Binary silicate glasses in the system CaO-SiO2 are synthesized over an extended composition range (42 mol % ≤ CaO ≤ 61 mol %), using container-less aerodynamic levitation techniques and CO2-laser heating. The compositional evolution of Q speciation in these glasses is quantified using (29)Si and (17)O magic angle spinning nuclear magnetic resonance spectroscopy. The results indicate progressive depolymerization of the silicate network upon addition of CaO and significant deviation of the Q speciation from the binary model. The equilibrium constants for the various Q species disproportionation reactions for these glasses are found to be similar to (much smaller than) those characteristic of Li (Mg)-silicate glasses, consistent with the corresponding trends in the field strengths of these modifier cations. Increasing CaO concentration results in an increase in the packing density and structural rigidity of these glasses and consequently in their glass transition temperature Tg. This apparent role reversal of conventional network-modifying cations in invert alkaline-earth silicate glasses are compared and contrasted with that in their alkali silicate counterparts.

Interpreting the 10 micron Astronomical Silicate Feature

NASA Astrophysics Data System (ADS)

Bowey, Janet E.

1998-11-01

10micron spectra of silicate dust in the diffuse medium towards Cyg OB2 no. 12 and towards field and embedded objects in the Taurus Molecular Cloud (TMC) were obtained with CGS3 at the United Kingdom Infrared Telescope (UKIRT). Cold molecular-cloud silicates are sampled in quiescent lines of sight towards the field stars Taurus-Elias 16 and Elias 13, whilst observations of the embedded young stellar objects HL Tau, Taurus-Elias 7 (Haro6-10) and Elias 18 also include emission from heated dust. To obtain the foreground silicate absorption profiles, featureless continua are estimated using smoothed astronomical and laboratory silicate emissivities. TMC field stars and Cyg OB2 no. 12 are modelled as photospheres reddened by foreground continuum and silicate extinction. Dust emission in the non-photospheric continua of HL Tau and Elias 7 (Haro6-10) is distinguished from foreground silicate absorption using a 10micron disk model, based on the IR-submm model of T Tauri stars by Adams, Lada & Shu (1988), with terms added to represent the foreground continuum and silicate extinction. The absorption profiles of HL Tau and Elias 7 are similar to that of the field star Elias 16. Fitted temperature indices of 0.43 (HL Tau) and 0.33 (Elias 7) agree with Boss' (1996) theoretical models of the 200-300K region, but are lower than those of IR-submm disks (0.5-0.61; Mannings & Emerson 1994); the modelled 10micron emission of HL Tau is optically thin, that of Elias 7 is optically thick. A preliminary arcsecond-resolution determination of the 10micron emissivity near θ1 Ori D in the Trapezium region of Orion and a range of emission temperatures (225-310K) are derived from observations by T. L. Hayward; this Ney-Allen emissivity is 0.6micron narrower than the Trapezium emissivity obtained by Forrest et al. (1975) with a large aperture. Published interstellar grain models, elemental abundances and laboratory studies of Solar System silicates (IDPs, GEMS and meteorites), the 10micron spectra of comets, interstellar silicates, synthetic silicates and terrestrial minerals, and the effects of laboratory processing on the 10micron spectra of crystalline and amorphous silicates are reviewed to provide insight into the mineralogy of interstellar silicate dust. The wavelengths of the peaks of the 10micron silicate profiles decrease between circumstellar, diffuse medium and molecular-cloud environments, indicating (after Gürtler & Henning 1986) that the amorphous pyroxene content of initially olivine-rich interstellar dust increases with time. This is accompanied by an increase in the FWHM of the features which indicates an increase in grain size and/or an increasing fraction of chemically-varied crystalline pyroxene. Fine structure in the Cyg OB2 no. 12, Elias 16, Elias 7, HL Tau profiles indicate that hydrated layer silicates similar to terrestrial serpentines, clays and talc may be a ubiquitous component of interstellar dust. At 10microns the narrow bands of mixed crystalline pyroxenes blend, making their identification difficult. Since no fine structure is observed near 11.2microns, the fraction of crystalline olivine is small. In geology direct olivine-plus-SiO2 to pyroxene reactions occur only at high pressure within the terrestrial mantle. Therefore the fraction of amorphous pyroxene is probably increased by the hydration of Mg-rich olivine to form a serpentine-like hydrated silicate, which is subsequently annealed to form a mixture of amorphous pyroxene and olivine. Terrestrial and laboratory olivine samples are readily converted to serpentine in the presence of water, and (after extended annealing) the first crystalline band to appear is the 11.2micron olivine feature frequently observed in cometary spectra.

Methylated silicates may explain the release of chlorinated methane from Martian soil

NASA Astrophysics Data System (ADS)

Bak, Ebbe N.; Jensen, Svend J. Knak; Nørnberg, Per; Finster, Kai

2016-01-01

The only organic compounds that have been detected in the Martian soil are simple chlorinated compounds released from heated surface material. However, the sources of the organic carbon are in dispute. Wind abraded silicates, which are widespread on the Martian surface, can sequester atmospheric methane which generates methylated silicates and thus could provide a mechanism for accumulation of reduced carbon in the surface soil. In this study we show that thermal volatilization of methylated silicates in the presence of perchlorate leads to the production of chlorinated methane. Thus, methylated silicates could be a source of the organic carbon released as chlorinated methane upon thermal volatilization of Martian soil samples. Further, our experiments show that the ratio of the different chlorinated compounds produced is dependent on the mass ratio of perchlorate to organic carbon in the soil.

Silicate Emission in the TW Hydrae Association

NASA Astrophysics Data System (ADS)

Sitko, Michael L.; Lynch, David K.; Russell, Ray W.

2000-11-01

The TW Hydrae association is the nearest young stellar association. Among its members are HD 98800, HR 4796A, and TW Hydrae itself, the nearest known classical T Tauri star. We have observed these three stars spectroscopically between 3 and 13 μm. In TW Hya, the spectrum shows a silicate emission feature that is similar to many other young stars' with protostellar disks. The 11.2 μm feature indicative of significant amounts of crystalline olivine is not as strong as in some young stars and solar system comets. In HR 4796A, the thermal emission in the silicate feature is very weak, suggesting little in the way of (small silicate) grains near the star. The silicate band of HD 98800 (observed by us, but also reported by Sylvester & Skinner) is intermediate in strength between TW Hya and HR 4796A.

Concentrations and behavior of oxygen and oxide ion in melts of composition CaO.MgO.xSiO2

NASA Technical Reports Server (NTRS)

Semkow, K. W.; Haskin, L. A.

1985-01-01

The behavior of oxygen and oxide ion in silicate melts was investigated through their electrochemical reactions at a platinum electrode. Values are given for the diffusion coefficient for molecular oxygen in diopside melt and the activation energy of diffusion. It is shown that molecular oxygen dissociates prior to undergoing reduction and that oxide ion reacts quickly with silicate polymers when it is produced. The concentration of oxide ion is kept low by a buffering effect of the silicate, the exact level being dependent on the silicate composition. Data on the kinetics of reaction of the dissociation of molecular oxygen and on the buffering reactions are provided. It is demonstrated that the data on oxygen in these silicate melts are consistent with those for solid buffers.

Geomorphology of unique reefs on the western Canadian shelf: sponge reefs mapped by multibeam bathymetry

NASA Astrophysics Data System (ADS)

Conway, Kim W.; Barrie, J. Vaughn; Krautter, Manfred

2005-09-01

Multibeam imagery of siliceous sponge reefs (Hexactinellida, Hexactinosida) reveals the setting, form, and organization of five reef complexes on the western Canadian continental shelf. The reefs are built by framework skeleton sponges which trap clay-rich sediments resulting in a distinctive pattern of low intensity backscatter from the reefs that colonize more reflective glacial sediments of higher backscatter intensity. Bathymetry and backscatter maps show the distribution and form of reefs in two large complexes in the Queen Charlotte Basin (QCB) covering hundreds of km2, and three smaller reef complexes in the Georgia Basin (GB). Ridges up to 7 km long and 21 m in height, together with diversely shaped, coalescing bioherms and biostromes form the principal reef shape in the QCB whereas chains of wave-form, streamlined mounds up to 14 m in height have developed in the GB. Reef initiation is dependent on the distribution of high backscatter-intensity relict glacial surfaces, and the variation in reef complex morphology is probably the result of tidally driven, near seabed currents.

Observations in the Saturn system during approach and orbital insertion, with Cassini's visual and infrared mapping spectrometer (VIMS)

USGS Publications Warehouse

Brown, R.H.; Baines, K.H.; Bellucci, G.; Buratti, B.J.; Capaccioni, F.; Cerroni, P.; Clark, R.N.; Coradini, A.; Cruikshank, D.P.; Drossart, P.; Formisano, V.; Jaumann, R.; Langevin, Y.; Matson, D.L.; McCord, T.B.; Mennella, V.; Nelson, R.M.; Nicholson, P.D.; Sicardy, B.; Sotin, Christophe; Baugh, N.; Griffith, C.A.; Hansen, G.B.; Hibbitts, C.A.; Momary, T.W.; Showalter, M.R.

2006-01-01

The Visual and Infrared Mapping Spectrometer observed Phoebe, Iapetus, Titan and Saturn's rings during Cassini's approach and orbital insertion. Phoebe's surface contains water ice, CO2, and ferrous iron. lapetus contains CO2 and organic materials. Titan's atmosphere shows methane fluorescence, and night-side atmospheric emission that may be CO2 and CH3D. As determined from cloud motions, the winds at altitude 25-30 km in the south polar region of Titan appear to be moving in a prograde direction at velocity ???1 m s-1. Circular albedo features on Titan's surface, seen at 2.02 ??m, may be palimpsests remaining from the rheological adjustment of ancient impact craters. As such, their long-term persistence is of special interest in view of the expected precipitation of liquids and solids from the atmosphere. Saturn's rings have changed little in their radial structure since the Voyager flybys in the early 1980s. Spectral absorption bands tentatively attributed to Fe2+ suggest that iron-bearing silicates are a source of contamination of the C ring and the Cassini Division. ?? ESO 2006.

Analysis of Colonial Currency

NASA Astrophysics Data System (ADS)

Kurkowski, Michael; Cangany, Catherine; Jordan, Louis; Manukyan, Khachatur; Schultz, Zachary; Wiescher, Michael

2017-09-01

This project entailed studying the cellulose in paper, the ink, colorants, and other materials used to produce American colonial currency. The technique primarily used in this project was X-Ray Fluorescence Spectroscopy (XRF). XRF mapping was used to provide both elemental analysis of large-scale objects as well as microscopic examination of individual pigment particles in ink, in addition to the inorganic additives used to prepare paper. The combination of elemental mapping with Fourier Transform Infrared (FTIR) and Raman Spectroscopies permits an efficient analysis of the currency. These spectroscopic methods help identify the molecular composition of the pigments. This combination of atomic and molecular analytical techniques provided an in-depth characterization of the paper currency on the macro, micro, and molecular levels. We have identified several of pigments that were used in the preparation of inks and colorants. Also, different inorganic crystals, such as alumina-silicates, have been detected in different papers. The FTIR spectroscopy allowed us to determine the type of cellulose fiber used in the production of paper currency. Our future research will be directed toward revealing important historical relationships between currencies printed throughout the colonies. ISLA Da Vinci Grant.

GEMS Revealed: Spectrum Imaging of Aggregate Grains in Interplanetary Dust

NASA Technical Reports Server (NTRS)

Keller, L. P.; Messenger, S.; Christoffersen, R.

2005-01-01

Anhydrous interplanetary dust particles (IDPs) of cometary origin contain abundant materials that formed in the early solar nebula. These materials were transported outward and subsequently mixed with molecular cloud materials and presolar grains in the region where comets accreted [1]. GEMS (glass with embedded metal and sulfides) grains are a major component of these primitive anhydrous IDPs, along with crystalline Mg-rich silicates, Fe-Ni sulfides, carbonaceous material, and other trace phases. Some GEMS grains (5%) are demonstrably presolar based on their oxygen isotopic compositions [2]. However, most GEMS grains are isotopically solar and have bulk chemical compositions that are incompatible with inferred compositions of interstellar dust, suggesting a solar system origin [3]. An alternative hypothesis is that GEMS grains represent highly irradiated interstellar grains whose oxygen isotopic compositions were homogenized through processing in the interstellar medium (ISM) [4]. We have obtained the first quantitative X-ray maps (spectrum images) showing the distribution of major and minor elements in individual GEMS grains. Nanometer-scale chemical maps provide critical data required to evaluate the differing models regarding the origin of GEMS grains.

Analysis of connectivity map: Control to glutamate injured and phenobarbital treated neuronal network

NASA Astrophysics Data System (ADS)

Kamal, Hassan; Kanhirodan, Rajan; Srinivas, Kalyan V.; Sikdar, Sujit K.

2010-04-01

We study the responses of a cultured neural network when it is exposed to epileptogenesis glutamate injury causing epilepsy and subsequent treatment with phenobarbital by constructing connectivity map of neurons using correlation matrix. This study is particularly useful in understanding the pharmaceutical drug induced changes in the neuronal network properties with insights into changes at the systems biology level.

History of Nebular Processing Traced by Silicate Stardust in IDPS

NASA Technical Reports Server (NTRS)

Messenger, Scott R.; Keller, L. P.; Nakamura-Messenger, K.

2010-01-01

Chondritic porous interplanetary dust particles (CP-IDPs) may be the best preserved remnants of primordial solar system materials, in part because they were not affected by parent body hydrothermal alteration. Their primitive characteristics include fine grained, unequilibrated, anhydrous mineralogy, enrichment in volatile elements, and abundant molecular cloud material and silicate stardust. However, while the majority of CP-IDP materials likely derived from the Solar System, their formation processes and provenance are poorly constrained. Stardust abundances provide a relative measure of the extent of processing that the Solar System starting materials has undergone in primitive materials. For example, among primitive meteorites silicate stardust abundances vary by over two orders of magnitude (less than 10-200 ppm). This range of abundances is ascribed to varying extents of aqueous processing in the meteorite parent bodies. The higher average silicate stardust abundances among CP-IDPs (greater than 375 ppm) are thus attributable to the lack of aqueous processing of these materials. Yet, silicate stardust abundances in IDPs also vary considerably. While the silicate stardust abundance in IDPs having anomalous N isotopic compositions was reported to be 375 ppm, the abundance in IDPs lacking N anomalies is less than 10 ppm. Furthermore, these values are significantly eclipsed among some IDPs with abundances ranging from 2,000 ppm to 10,000 ppm. Given that CP-IDPs have not been significantly affected by parent body processes, the difference in silicate stardust abundances among these IDPs must reflect varying extents of nebular processing. Here we present recent results of a systematic coordinated mineralogical/isotopic study of large cluster IDPs aimed at (1) characterizing the mineralogy of presolar silicates and (2) delineating the mineralogical and petrographic characteristics of IDPs with differing silicate stardust abundances. One of the goals of this study is to better understand the earliest stages of evolution of the Solar System starting materials.

Three-dimensional culture of dental pulp stem cells in direct contact to tricalcium silicate cements.

PubMed

Widbiller, M; Lindner, S R; Buchalla, W; Eidt, A; Hiller, K-A; Schmalz, G; Galler, K M

2016-03-01

Calcium silicate cements are biocompatible dental materials applicable in contact with vital tissue. The novel tricalcium silicate cement Biodentine™ offers properties superior to commonly used mineral trioxide aggregate (MTA). Objective of this study was to evaluate its cytocompatibility and ability to induce differentiation and mineralization in three-dimensional cultures of dental pulp stem cells after direct contact with the material. Test materials included a new tricalcium silicate (Biodentine™, Septodont, Saint-Maur-des-Fossés, France), MTA (ProRoot® MTA, DENSPLY Tulsa Dental Specialities, Johnson City, TN, USA), glass ionomer (Ketac™ Molar Aplicap™, 3M ESPE, Seefeld, Germany), human dentin disks and polystyrene. Magnetic activated cell sorting for to the surface antigen STRO-1 was performed to gain a fraction enriched with mesenchymal stem cells. Samples were allowed to set and dental pulp stem cells in collagen carriers were placed on top. Scanning electron microscopy of tricalcium silicate cement surfaces with and without cells was conducted. Cell viability was measured for 14 days by MTT assay. Alkaline phosphatase activity was evaluated (days 3, 7, and 14) and expression of mineralization-associated genes (COL1A1, ALP, DSPP, and RUNX2) was quantified by real-time quantitative PCR. Nonparametric statistical analysis for cell viability and alkaline phosphatase data was performed to compare different materials as well as time points (Mann-Whitney U test, α = 0.05). Cell viability was highest on tricalcium silicate cement, followed by MTA. Viability on glass ionomer cement and dentin disks was significantly lower. Alkaline phosphatase activity was lower in cells on new tricalcium silicate cement compared to MTA, whereas expression patterns of marker genes were alike. Increased cell viability and similar levels of mineralization-associated gene expression in three-dimensional cell cultures on the novel tricalcium silicate cement and mineral trioxide aggregate indicate that the material is cytocompatible and bioactive. The tested new tricalcium silicate cement confirms its suitability as an alternative to MTA in vital pulp therapy.

The stable Cr isotopic compositions of chondrites and silicate planetary reservoirs

NASA Astrophysics Data System (ADS)

Schoenberg, Ronny; Merdian, Alexandra; Holmden, Chris; Kleinhanns, Ilka C.; Haßler, Kathrin; Wille, Martin; Reitter, Elmar

2016-06-01

The depletion of chromium in Earth's mantle (∼2700 ppm) in comparison to chondrites (∼4400 ppm) indicates significant incorporation of chromium into the core during our planet's metal-silicate differentiation, assuming that there was no significant escape of the moderately volatile element chromium during the accretionary phase of Earth. Stable Cr isotope compositions - expressed as the ‰-difference in 53Cr/52Cr from the terrestrial reference material SRM979 (δ53/52CrSRM979 values) - of planetary silicate reservoirs might thus yield information about the conditions of planetary metal segregation processes when compared to chondrites. The stable Cr isotopic compositions of 7 carbonaceous chondrites, 11 ordinary chondrites, 5 HED achondrites and 2 martian meteorites determined by a double spike MC-ICP-MS method are within uncertainties indistinguishable from each other and from the previously determined δ53/52CrSRM979 value of -0.124 ± 0.101‰ for the igneous silicate Earth. Extensive quality tests support the accuracy of the stable Cr isotope determinations of various meteorites and terrestrial silicates reported here. The uniformity in stable Cr isotope compositions of samples from planetary silicate mantles and undifferentiated meteorites indicates that metal-silicate differentiation of Earth, Mars and the HED parent body did not cause measurable stable Cr isotope fractionation between these two reservoirs. Our results also imply that the accretionary disc, at least in the inner solar system, was homogeneous in its stable Cr isotopic composition and that potential volatility loss of chromium during accretion of the terrestrial planets was not accompanied by measurable stable isotopic fractionation. Small but reproducible variations in δ53/52CrSRM979 values of terrestrial magmatic rocks point to natural stable Cr isotope variations within Earth's silicate reservoirs. Further and more detailed studies are required to investigate whether silicate differentiation processes, such as partial mantle melting and crystal fractionation, can cause stable Cr isotopic fractionation on Earth and other planetary bodies.

The W-W02 Oxygen Fugacity Buffer at High Pressures and Temperatures: Implications for f02 Buffering and Metal-silicate Partitioning

NASA Technical Reports Server (NTRS)

Shofner, G. A.; Campbell, A. J.; Danielson, L.; Righter, K.

2013-01-01

Oxygen fugacity (fO2) controls multivalent phase equilibria and partitioning of redox-sensitive elements, and it is important to understand this thermodynamic parameter in experimental and natural systems. The coexistence of a metal and its oxide at equilibrium constitutes an oxygen buffer which can be used to control or calculate fO2 in high pressure experiments. Application of 1-bar buffers to high pressure conditions can lead to inaccuracies in fO2 calculations because of unconstrained pressure dependencies. Extending fO2 buffers to pressures and temperatures corresponding to the Earth's deep interior requires precise determinations of the difference in volume (Delta) V) between the buffer phases. Synchrotron x-ray diffraction data were obtained using diamond anvil cells (DAC) and a multi anvil press (MAP) to measure unit cell volumes of W and WO2 at pressures and temperatures up to 70 GPa and 2300 K. These data were fitted to Birch-Murnaghan 3rd-order thermal equations of state using a thermal pressure approach; parameters for W are KT = 306 GPa, KT' = 4.06, and aKT = 0.00417 GPa K-1. Two structural phase transitions were observed for WO2 at 4 and 32 GPa with structures in P21/c, Pnma and C2/c space groups. Equations of state were fitted for these phases over their respective pressure ranges yielding the parameters KT = 190, 213, 300 GPa, KT' = 4.24, 5.17, 4 (fixed), and aKT = 0.00506, 0.00419, 0.00467 GPa K-1 for the P21/c, Pnma and C2/c phases, respectively. The W-WO2 buffer (WWO) was extended to high pressure by inverting the W and WO2 equations of state to obtain phase volumes at discrete pressures (1-bar to 100 GPa, 1 GPa increments) along isotherms (300 to 3000K, 100 K increments). The slope of the absolute fO2 of the WWO buffer is positive with increasing temperature up to approximately 70 GPa and is negative above this pressure. The slope is positive along isotherms from 1000 to 3000K with increasing pressure up to at least 100 GPa. The WWO buffer is at a higher fO2 than the IW buffer at pressures lower than 40 GPa, and the magnitude of this difference decreases at higher pressures. This qualitatively indicates an increasingly lithophile character for W at higher pressures. The WWO buffer was quantitatively applied to W metal-silicate partitioning by using the WWO-IW buffer difference in combination with literature data on W metal-silicate partitioning to model the exchange coefficient (KD) for the Fe-W exchange reaction. This approach captures the pressure dependence of W metal-silicate partitioning using the WWO-IW buffer difference and models the activities of the components in the silicate and metallic phases using an expression of the Gibbs excess energy of mixing. Calculation of KD along a peridotite liquidus predicts a decrease in W siderophility at higher pressures that supports the qualitative behavior predicted by the WWO-IW buffer difference, and agrees with findings of others. Comparing the competing effects of temperature and pressure on W metal-silicate partitioning, our results indicate that pressure exerts a greater effect.