40 CFR 59.110 - Incorporations by Reference.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Register. (1) ASTM D 1613-96, Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products, IBR approved for § 59.104(d). (2) ASTM D... Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA, 19428, telephone...

30 CFR 75.1900 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... serve its intended function for 1 hour when subjected to a fire test incorporating an ASTM E119-88 time/temperature heat input, or equivalent. The publication ASTM E119-88 “Standard Test Methods for Fire Tests of... for Testing Materials (ASTM), 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA, 19428-2959...

ASTM Validates Air Pollution Test Methods

ERIC Educational Resources Information Center

Chemical and Engineering News, 1973

1973-01-01

The American Society for Testing and Materials (ASTM) has validated six basic methods for measuring pollutants in ambient air as the first part of its Project Threshold. Aim of the project is to establish nationwide consistency in measuring pollutants; determining precision, accuracy and reproducibility of 35 standard measuring methods. (BL)

Stress Corrosion Testing

NASA Technical Reports Server (NTRS)

1985-01-01

Advanced testing of structural materials was developed by Lewis Research Center and Langley Research Center working with the American Society for Testing and Materials (ASTM). Under contract, Aluminum Company of America (Alcoa) conducted a study for evaluating stress corrosion cracking, and recommended the "breaking load" method which determines fracture strengths as well as measuring environmental degradation. Alcoa and Langley plan to submit the procedure to ASTM as a new testing method.

Final Report, Volume 2, The Development of Qualification Standards for Cast Duplex Stainless Steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russell, Steven, W.; Lundin, Carl, W.

2005-09-30

The scope of testing cast Duplex Stainless Steel (DSS) required testing to several ASTM specifications, while formulating and conducting industry round robin tests to verify and study the reproducibility of the results. ASTM E562 (Standard Test Method for Determining Volume Fraction by Systematic manual Point Count) and ASTM A923 (Standard Test Methods for Detecting Detrimental Intermetallic Phase in Wrought Duplex Austenitic/Ferritic Stainless Steels) were the specifications utilized in conducting this work. An ASTM E562 industry round robin, ASTM A923 applicability study, ASTM A923 industry round robin, and an ASTM A923 study of the effectiveness of existing foundry solution annealing proceduresmore » for producing cast DSS without intermetallic phases were implemented. In the ASTM E562 study, 5 samples were extracted from various cast austenitic and DSS in order to have varying amounts of ferrite. Each sample was metallographically prepared by UT and sent to each of 8 participants for volume fraction of ferrite measurements. Volume fraction of ferrite was measured using manual point count per ASTM E562. FN was measured from the Feritescope® and converted to volume fraction of ferrite. Results indicate that ASTM E562 is applicable to DSS and the results have excellent lab-to-lab reproducibility. Also, volume fraction of ferrite conversions from the FN measured by the Feritescope® were similar to volume fraction of ferrite measured per ASTM E562. In the ASTM A923 applicability to cast DSS study, 8 different heat treatments were performed on 3 lots of ASTM A890-4A (CD3MN) castings and 1 lot of 2205 wrought DSS. The heat treatments were selected to produce a wide range of cooling rates and hold times in order to study the suitability of ASTM A923 to the response of varying amounts on intermetallic phases [117]. The test parameters were identical to those used to develop ASTM A923 for wrought DSS. Charpy V-notch impact samples were extracted from the castings and wrought DSS and tested per ASTM A923 method B (Charpy impact test). Method A (sodium hydroxide etch test) was performed on one half of a fractured Charpy V-notch impact sample and Method C (ferric chloride corrosion weight loss test) was performed on another half. Test results for the three cast lots and one wrought lot indicate that ASTM A923 is relevant for detecting intermetallic phases in cast DSS. In the ASTM A923 round robin study, five laboratories conducted ASTM A923 Methods A & C on cast DSS material and the lab-to-lab reproducibility of the data was determined. Two groups of samples were sent to the participants. Group 1 samples were tested per ASTM A923 Method A, group 2 samples were tested by ASTM A923 Method C. Testing procedures for this round robin study were identical to those used in the ASTM A923 applicability study. Results from this round robin indicate that there is excellent lab-to-lab reproducibility of ASTM A923 with respect to cast DSS and that ASTM A923 could be expanded to cover both wrought and cast DSS. In the ASTM A923 study of the effectiveness of existing foundry solution annealing procedures for producing cast DSS without intermetallic phases, Ten heats of ASTM A890-4A (CD3MN) in the foundry solution annealed condition were tested per ASTM A923 Methods A, B, & C. Testing of these materials per ASTM A923 was used to determine if the foundry solution anneal procedures were adequate to completely eliminate any intermetallic phases, which may have precipitated during the casting and subsequent heat treatment processes. All heats showed no sign of intermetallic phase per Method A, passed minimum Charpy impact energy requirements per Method B (> 40 ft-lbs @ -40°C (-40°F)), and showed negligible weight loss per Method C (< 10 mdd). These results indicate that the solution annealing procedure used by foundries is adequate to produce a product free from intermetallic phases.« less

Final Report, Volume 2, The Development of Qualification Standards for Cast Duplex Stainless Steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russell, Steven, W.; Lundin, Carl, D.

2005-09-30

The scope of testing cast Duplex Stainless Steel (DSS) required testing to several ASTM specifications, while formulating and conducting industry round robin tests to verify and study the reproducibility of the results. ASTM E562 (Standard Test Method for Determining Volume Fraction by Systematic manual Point Count) and ASTM A923 (Standard Test Methods for Detecting Detrimental Intermetallic Phase in Wrought Duplex Austenitic/Ferritic Stainless Steels) were the specifications utilized in conducting this work. An ASTM E562 industry round robin, ASTM A923 applicability study, ASTM A923 industry round robin, and an ASTM A923 study of the effectiveness of existing foundry solution annealing proceduresmore » for producing cast DSS without intermetallic phases were implemented. In the ASTM E562 study, 5 samples were extracted from various cast austenitic and DSS in order to have varying amounts of ferrite. Each sample was metallographically prepared by UT and sent to each of 8 participants for volume fraction of ferrite measurements. Volume fraction of ferrite was measured using manual point count per ASTM E562. FN was measured from the Feritescope{reg_sign} and converted to volume fraction of ferrite. Results indicate that ASTM E562 is applicable to DSS and the results have excellent lab-to-lab reproducibility. Also, volume fraction of ferrite conversions from the FN measured by the Feritescope{reg_sign} were similar to volume fraction of ferrite measured per ASTM E562. In the ASTM A923 applicability to cast DSS study, 8 different heat treatments were performed on 3 lots of ASTM A890-4A (CD3MN) castings and 1 lot of 2205 wrought DSS. The heat treatments were selected to produce a wide range of cooling rates and hold times in order to study the suitability of ASTM A923 to the response of varying amounts on intermetallic phases [117]. The test parameters were identical to those used to develop ASTM A923 for wrought DSS. Charpy V-notch impact samples were extracted from the castings and wrought DSS and tested per ASTM A923 method B (Charpy impact test). Method A (sodium hydroxide etch test) was performed on one half of a fractured Charpy V-notch impact sample and Method C (ferric chloride corrosion weight loss test) was performed on another half. Test results for the three cast lots and one wrought lot indicate that ASTM A923 is relevant for detecting intermetallic phases in cast DSS. In the ASTM A923 round robin study, five laboratories conducted ASTM A923 Methods A & C on cast DSS material and the lab-to-lab reproducibility of the data was determined. Two groups of samples were sent to the participants. Group 1 samples were tested per ASTM A923 Method A, group 2 samples were tested by ASTM A923 Method C. Testing procedures for this round robin study were identical to those used in the ASTM A923 applicability study. Results from this round robin indicate that there is excellent lab-to-lab reproducibility of ASTM A923 with respect to cast DSS and that ASTM A923 could be expanded to cover both wrought and cast DSS. In the ASTM A923 study of the effectiveness of existing foundry solution annealing procedures for producing cast DSS without intermetallic phases, Ten heats of ASTM A890-4A (CD3MN) in the foundry solution annealed condition were tested per ASTM A923 Methods A, B, & C. Testing of these materials per ASTM A923 was used to determine if the foundry solution anneal procedures were adequate to completely eliminate any intermetallic phases, which may have precipitated during the casting and subsequent heat treatment processes. All heats showed no sign of intermetallic phase per Method A, passed minimum Charpy impact energy requirements per Method B (> 40 ft-lbs {at} -40 C (-40 F)), and showed negligible weight loss per Method C (< 10 mdd). These results indicate that the solution annealing procedure used by foundries is adequate to produce a product free from intermetallic phases.« less

Life Prediction/Reliability Data of Glass-Ceramic Material Determined for Radome Applications

NASA Technical Reports Server (NTRS)

Choi, Sung R.; Gyekenyesi, John P.

2002-01-01

Brittle materials, ceramics, are candidate materials for a variety of structural applications for a wide range of temperatures. However, the process of slow crack growth, occurring in any loading configuration, limits the service life of structural components. Therefore, it is important to accurately determine the slow crack growth parameters required for component life prediction using an appropriate test methodology. This test methodology also should be useful in determining the influence of component processing and composition variables on the slow crack growth behavior of newly developed or existing materials, thereby allowing the component processing and composition to be tailored and optimized to specific needs. Through the American Society for Testing and Materials (ASTM), the authors recently developed two test methods to determine the life prediction parameters of ceramics. The two test standards, ASTM 1368 for room temperature and ASTM C 1465 for elevated temperatures, were published in the 2001 Annual Book of ASTM Standards, Vol. 15.01. Briefly, the test method employs constant stress-rate (or dynamic fatigue) testing to determine flexural strengths as a function of the applied stress rate. The merit of this test method lies in its simplicity: strengths are measured in a routine manner in flexure at four or more applied stress rates with an appropriate number of test specimens at each applied stress rate. The slow crack growth parameters necessary for life prediction are then determined from a simple relationship between the strength and the applied stress rate. Extensive life prediction testing was conducted at the NASA Glenn Research Center using the developed ASTM C 1368 test method to determine the life prediction parameters of a glass-ceramic material that the Navy will use for radome applications.

49 CFR 178.345-2 - Material and material thickness.

Code of Federal Regulations, 2010 CFR

2010-10-01

... authorized for cargo tanks “constructed in accordance with the ASME Code”, Section VIII. ASTM A 569 ASTM A 570 ASTM A 572 ASTM A 622 ASTM A 656 ASTM A 715 ASTM A 1008/ A 1008M, ASTM A 1011/A 1011M (2) Aluminum... ASTM specifications may be used for cargo tanks “constructed in accordance with the ASME Code”: ASTM B...

Environmentally safe aviation fuels

NASA Technical Reports Server (NTRS)

Liberio, Patricia D.

1995-01-01

In response to the Air Force directive to remove Ozone Depleting Chemicals (ODC's) from military specifications and Defense Logistics Agency's Hazardous Waste Minimization Program, we are faced with how to ensure a quality aviation fuel without using such chemicals. Many of these chemicals are found throughout the fuel and fuel related military specifications and are part of test methods that help qualify the properties and quality of the fuels before they are procured. Many years ago there was a directive for military specifications to use commercially standard test methods in order to provide standard testing in private industry and government. As a result the test methods used in military specifications are governed by the American Society of Testing and Materials (ASTM). The Air Force has been very proactive in the removal or replacement of the ODC's and hazardous materials in these test methods. For example, ASTM D3703 (Standard Test Method for Peroxide Number of Aviation Turbine Fuels), requires the use of Freon 113, a known ODC. A new rapid, portable hydroperoxide test for jet fuels similar to ASTM D3703 that does not require the use of ODC's has been developed. This test has proved, in limited testing, to be a viable substitute method for ASTM D3703. The Air Force is currently conducting a round robin to allow the method to be accepted by ASTM and therefore replace the current method. This paper will describe the Air Force's initiatives to remove ODC's and hazardous materials from the fuel and fuel related military specifications that the Air Force Wright Laboratory.

ASTM METHODS

EPA Science Inventory

ASTM is a not-for-profit organization that provides a forum for producers, users, ultimate consumers, and those having a general interest (representatives of government and academia) to meet on common ground and write standards for materials, products, systems, and services. From...

ASTM E 1559 method for measuring material outgassing/deposition kinetics has applications to aerospace, electronics, and semiconductor industries

NASA Technical Reports Server (NTRS)

Garrett, J. W.; Glassford, A. P. M.; Steakley, J. M.

1994-01-01

The American Society for Testing and Materials has published a new standard test method for characterizing time and temperature-dependence of material outgassing kinetics and the deposition kinetics of outgassed species on surfaces at various temperatures. This new ASTM standard, E 1559(1), uses the quartz crystal microbalance (QCM) collection measurement approach. The test method was originally developed under a program sponsored by the United States Air Force Materials Laboratory (AFML) to create a standard test method for obtaining outgassing and deposition kinetics data for spacecraft materials. Standardization by ASTM recognizes that the method has applications beyond aerospace. In particular, the method will provide data of use to the electronics, semiconductor, and high vacuum industries. In ASTM E 1559 the material sample is held in vacuum in a temperature-controlled effusion cell, while its outgassing flux impinges on several QCM's which view the orifice of the effusion cell. Sample isothermal total mass loss (TML) is measured as a function of time from the mass collected on one of the QCM's which is cooled by liquid nitrogen, and the view factor from this QCM to the cell. The amount of outgassed volatile condensable material (VCM) on surfaces at higher temperatures is measured as a function of time during the isothermal outgassing test by controlling the temperatures of the remaining QCM's to selected values. The VCM on surfaces at temperatures in between those of the collector QCM's is determined at the end of the isothermal test by heating the QCM's at a controlled rate and measuring the mass loss from the end of the QCM's as a function of time and temperature. This reevaporation of the deposit collected on the QCM's is referred to as QCM thermogravimetric analysis. Isothermal outgassing and deposition rates can be determined by differentiating the isothermal TML and VCM data, respectively, while the evaporation rates of the species can be obtained as a function of temperature by differentiating the QCM thermogravimetric analysis data.

Comparative field permeability measurement of permeable pavements using ASTM C1701 and NCAT permeameter methods.

PubMed

Li, Hui; Kayhanian, Masoud; Harvey, John T

2013-03-30

Fully permeable pavement is gradually gaining support as an alternative best management practice (BMP) for stormwater runoff management. As the use of these pavements increases, a definitive test method is needed to measure hydraulic performance and to evaluate clogging, both for performance studies and for assessment of permeability for construction quality assurance and maintenance needs assessment. Two of the most commonly used permeability measurement tests for porous asphalt and pervious concrete are the National Center for Asphalt Technology (NCAT) permeameter and ASTM C1701, respectively. This study was undertaken to compare measured values for both methods in the field on a variety of permeable pavements used in current practice. The field measurements were performed using six experimental section designs with different permeable pavement surface types including pervious concrete, porous asphalt and permeable interlocking concrete pavers. Multiple measurements were performed at five locations on each pavement test section. The results showed that: (i) silicone gel is a superior sealing material to prevent water leakage compared with conventional plumbing putty; (ii) both methods (NCAT and ASTM) can effectively be used to measure the permeability of all pavement types and the surface material type will not impact the measurement precision; (iii) the permeability values measured with the ASTM method were 50-90% (75% on average) lower than those measured with the NCAT method; (iv) the larger permeameter cylinder diameter used in the ASTM method improved the reliability and reduced the variability of the measured permeability. Copyright © 2013 Elsevier Ltd. All rights reserved.

Comparative study of methods to measure the density of Cementious powders

PubMed Central

Helsel, Michelle A.; Bentz, Dale

2016-01-01

The accurate measurement of the density of hydraulic cement has an essential role in the determination of concrete mixture proportions. As more supplementary cementitious materials (SCM), such as fly ash, and slag, or cement replacements materials such as limestone and calcium carbonate are used in blended cements, knowledge of the density of each powder or of the blended cement would allow a more accurate calculation of the proportions of a concrete mixture by volume instead of by mass. The current ASTM standard for measuring cement density is the “Test Method for Density of Hydraulic Cements” (ASTM C188-14), which utilizes a liquid displacement method to measure the volume of the cement. This paper will examine advantageous modifications of the current ASTM test, by alcohol substitutions for kerosene. In addition, a gas (helium) pycnometry method is evaluated as a possible alternative to the current standard. The described techniques will be compared to determine the most precise and reproducible method for measuring the density of hydraulic cements and other powders. PMID:27099404

Comparative study of methods to measure the density of Cementious powders.

PubMed

Helsel, Michelle A; Ferraris, Chiara F; Bentz, Dale

2016-11-01

The accurate measurement of the density of hydraulic cement has an essential role in the determination of concrete mixture proportions. As more supplementary cementitious materials (SCM), such as fly ash, and slag, or cement replacements materials such as limestone and calcium carbonate are used in blended cements, knowledge of the density of each powder or of the blended cement would allow a more accurate calculation of the proportions of a concrete mixture by volume instead of by mass. The current ASTM standard for measuring cement density is the "Test Method for Density of Hydraulic Cements" (ASTM C188-14), which utilizes a liquid displacement method to measure the volume of the cement. This paper will examine advantageous modifications of the current ASTM test, by alcohol substitutions for kerosene. In addition, a gas (helium) pycnometry method is evaluated as a possible alternative to the current standard. The described techniques will be compared to determine the most precise and reproducible method for measuring the density of hydraulic cements and other powders.

40 CFR 60.17 - Incorporations by reference.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (C267-01), U.S. EPA, Research Triangle Park, NC or at the National Archives and Records Administration... Testing and Materials (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428...) ASTM D86-96, Standard Test Method for Distillation of Petroleum Products (Approved April 10, 1996), IBR...

Mode II Interlaminar Fracture Toughness and Fatigue Characterization of a Graphite Epoxy Composite Material

NASA Technical Reports Server (NTRS)

O'Brien, T. Kevin; Johnston, William M.; Toland, Gregory J.

2010-01-01

Mode II interlaminar fracture toughness and delamination onset and growth characterization data were generated for IM7/8552 graphite epoxy composite materials from two suppliers for use in fracture mechanics analyses. Both the fracture toughness testing and the fatigue testing were conducted using the End-notched Flexure (ENF) test. The ENF test for mode II fracture toughness is currently under review by ASTM as a potential standard test method. This current draft ASTM protocol was used as a guide to conduct the tests on the IM7/8552 material. This report summarizes the test approach, methods, procedures and results of this characterization effort.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lindahl, P.C.

A proposed American Society for Testing and Materials (ASTM) method for the determination of arsenic and selenium content in coal has been used and evaluated in the Analytical Chemistry Laboratory (ACL) at Argonne National Laboratory (ANL) as part of an interlaboratory study. Coal is conducted with Eschka's mixture (MgO + Na/sub 2/CO/sub 3/), followed by determination of the aresnic and selenium content by hydride generation/atomic absorption spectrophotometry. The method was evaluated on a series of coals, including two National Bureau of Standards-Standards Reference Material (NBS-SRM) coals and twelve ASTM coal samples. Comparison of ACL/ANL arsenic and selenium data for themore » suite of coal analyzed showed excellent agreement with certified values for the NBS-SRM coals and with interlaboratory data from five other laboratories for the ASTM coals. 11 refs., 3 figs., 6 tabs.« less

ASTM test methods for composite characterization and evaluation

NASA Technical Reports Server (NTRS)

Masters, John E.

1994-01-01

A discussion of the American Society for Testing and Materials is given. Under the topic of composite materials characterization and evaluation, general industry practice and test methods for textile composites are presented.

40 CFR 92.5 - Reference materials.

Code of Federal Regulations, 2011 CFR

2011-07-01

... § 92.113 ASTM D 1945-91, Standard Test Method for Analysis of Natural Gas by Gas Chromatography § 92... Supercritical Fluid Chromatography § 92.113 ASTM E 29-93a, Standard Practice for Using Significant Digits in....119 SAE Recommended Practice J244, Measurement of Intake Air or Exhaust Gas Flow of Diesel Engines...

Analytical methods for determining fire resistance of timber members

Treesearch

Robert H. White

2008-01-01

The fire resistance ratings of wood members and assemblies, as of other materials, have traditionally been obtained by testing the assembly in a furnace in accordance with ASTM International (ASTM) Standard E119, International Organization for Standardization (ISO) Standard 834, and similar standards. These ratings are published in listings, such as Underwriters...

46 CFR 160.077-19 - Approval Testing-Recreational Hybrid PFD's.

Code of Federal Regulations, 2010 CFR

2010-10-01

... distribution, and inflation medium retention test, UL 1517, sections 18 and 19, except: (i) Recreational hybrid... Method Standard 191, or ASTM D 751 (incorporated by reference, see § 160.077-5). (4) Permeability. The permeability of chamber materials must be determined according to ASTM D 1434 (incorporated by reference, see...

46 CFR 160.077-19 - Approval Testing-Recreational Hybrid PFD's.

Code of Federal Regulations, 2013 CFR

2013-10-01

... distribution, and inflation medium retention test, UL 1517, sections 18 and 19, except: (i) Recreational hybrid... Method Standard 191, or ASTM D 751 (incorporated by reference, see § 160.077-5). (4) Permeability. The permeability of chamber materials must be determined according to ASTM D 1434 (incorporated by reference, see...

46 CFR 160.077-19 - Approval Testing-Recreational Hybrid PFD's.

Code of Federal Regulations, 2011 CFR

2011-10-01

... distribution, and inflation medium retention test, UL 1517, sections 18 and 19, except: (i) Recreational hybrid... Method Standard 191, or ASTM D 751 (incorporated by reference, see § 160.077-5). (4) Permeability. The permeability of chamber materials must be determined according to ASTM D 1434 (incorporated by reference, see...

46 CFR 160.077-19 - Approval Testing-Recreational Hybrid PFD's.

Code of Federal Regulations, 2012 CFR

2012-10-01

... distribution, and inflation medium retention test, UL 1517, sections 18 and 19, except: (i) Recreational hybrid... Method Standard 191, or ASTM D 751 (incorporated by reference, see § 160.077-5). (4) Permeability. The permeability of chamber materials must be determined according to ASTM D 1434 (incorporated by reference, see...

46 CFR 160.077-19 - Approval Testing-Recreational Hybrid PFD's.

Code of Federal Regulations, 2014 CFR

2014-10-01

... distribution, and inflation medium retention test, UL 1517, sections 18 and 19, except: (i) Recreational hybrid... Method Standard 191, or ASTM D 751 (incorporated by reference, see § 160.077-5). (4) Permeability. The permeability of chamber materials must be determined according to ASTM D 1434 (incorporated by reference, see...

Development of ASTM Standard for SiC-SiC Joint Testing Final Scientific/Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jacobsen, George; Back, Christina

2015-10-30

As the nuclear industry moves to advanced ceramic based materials for cladding and core structural materials for a variety of advanced reactors, new standards and test methods are required for material development and licensing purposes. For example, General Atomics (GA) is actively developing silicon carbide (SiC) based composite cladding (SiC-SiC) for its Energy Multiplier Module (EM2), a high efficiency gas cooled fast reactor. Through DOE funding via the advanced reactor concept program, GA developed a new test method for the nominal joint strength of an endplug sealed to advanced ceramic tubes, Fig. 1-1, at ambient and elevated temperatures called themore » endplug pushout (EPPO) test. This test utilizes widely available universal mechanical testers coupled with clam shell heaters, and specimen size is relatively small, making it a viable post irradiation test method. The culmination of this effort was a draft of an ASTM test standard that will be submitted for approval to the ASTM C28 ceramic committee. Once the standard has been vetted by the ceramics test community, an industry wide standard methodology to test joined tubular ceramic components will be available for the entire nuclear materials community.« less

Determination of MIL-H-6083 Hydraulic Fluid In-Service Use Limits for Self-Propelled Artillery

DTIC Science & Technology

1991-09-01

determined using the American Society for Testing and Materials (ASTM) D1744 Karl Fischer Reagent method . The specification limit is 0.05% (500 pans per...cazefully controlled. TOTAL ACID NUMBER The acid number was determined by the ASTM D664 potentiometric titration test method . Unfortunately, data were...fluid condition t results with AOAP tent date was found. The Navy Patch Kit method for particle contamination meamrement was evaluated as a possible

Solvent Assisted Delamination Crack Growth Behavior of Amorphous Thermoplastic Materials

DTIC Science & Technology

1989-02-01

72CRD285. October 1972. 4. Standard Method of Test for Plane- Strain Fracture Toughness of Metallic Materials. 1988 Annual Book of ASTM Standards, Technical...intensity factor K I or the associated strain energy release rate, G I . ASTM compact tension test yields stress intensity factor, KI, via Equation 1...are such that a constant deadweight load results in increasing strain energy release rate with increasing crack length. Figure 3 shows the neat resin

40 CFR 90.7 - Reference materials.

Code of Federal Regulations, 2013 CFR

2013-07-01

... EMISSIONS FROM NONROAD SPARK-IGNITION ENGINES AT OR BELOW 19 KILOWATTS General § 90.7 Reference materials... Fuels by the Research Method Appendix A to subpart D, Table 3. ASTM D2700-92: Standard Test Method for...

40 CFR 90.7 - Reference materials.

Code of Federal Regulations, 2014 CFR

2014-07-01

... EMISSIONS FROM NONROAD SPARK-IGNITION ENGINES AT OR BELOW 19 KILOWATTS General § 90.7 Reference materials... Fuels by the Research Method Appendix A to subpart D, Table 3. ASTM D2700-92: Standard Test Method for...

40 CFR 90.7 - Reference materials.

Code of Federal Regulations, 2012 CFR

2012-07-01

... EMISSIONS FROM NONROAD SPARK-IGNITION ENGINES AT OR BELOW 19 KILOWATTS General § 90.7 Reference materials... Fuels by the Research Method Appendix A to subpart D, Table 3. ASTM D2700-92: Standard Test Method for...

40 CFR 60.17 - Incorporations by reference.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (C267-01), U.S. EPA, Research Triangle Park, NC or at the National Archives and Records Administration... Testing and Materials (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428...), 60.593(d), 60.593a(d), and 60.633(h). (8) ASTM D129-64, 78, 95, 00, Standard Test Method for Sulfur...

40 CFR 60.17 - Incorporations by reference.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (C267-01), U.S. EPA, Research Triangle Park, NC or at the National Archives and Records Administration... Testing and Materials (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428...), 60.593(d), 60.593a(d), and 60.633(h). (8) ASTM D129-64, 78, 95, 00, Standard Test Method for Sulfur...

78 FR 63164 - Certain Small Diameter Carbon and Alloy Seamless Standard, Line and Pressure Pipe From Romania...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-23

... American Society for Testing and Materials (ASTM) A- 53, ASTM A-106, ASTM A-333, ASTM A-334, ASTM A-335, ASTM A-589, ASTM A- 795, and the American Petroleum Institute (API) 5L specifications and meeting the... to the application of external heat. Seamless carbon steel pressure pipe meeting the ASTM A- 106...

47 CFR 90.379 - ASTM E2213-03 DSRC Standard (ASTM-DSRC Standard).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false ASTM E2213-03 DSRC Standard (ASTM-DSRC Standard... Communications Service (dsrcs) § 90.379 ASTM E2213-03 DSRC Standard (ASTM-DSRC Standard). Roadside Units... incorporated by reference: American Society for Testing and Materials (ASTM) E2213-03, “Standard Specification...

Mechanical Properties of a High Lead Glass Used in the Mars Organic Molecule Analyzer

NASA Technical Reports Server (NTRS)

Salem, Jonathan A.; Smith, Nathan A.; Ersahin, Akif

2015-01-01

The elastic constants, strength, fracture toughness, slow crack growth parameters, and mirror constant of a high lead glass supplied as tubes and funnels were measured using ASTM International (formerly ASTM, American Society for Testing and Materials) methods and modifications thereof. The material exhibits lower Young's modulus and slow crack growth exponent as compared to soda-lime silica glass. Highly modified glasses exhibit lower fracture toughness and slow crack growth exponent than high purity glasses such as fused silica.

Automated acid and base number determination of mineral-based lubricants by fourier transform infrared spectroscopy: commercial laboratory evaluation.

PubMed

Winterfield, Craig; van de Voort, F R

2014-12-01

The Fluid Life Corporation assessed and implemented Fourier transform infrared spectroscopy (FTIR)-based methods using American Society for Testing and Materials (ASTM)-like stoichiometric reactions for determination of acid and base number for in-service mineral-based oils. The basic protocols, quality control procedures, calibration, validation, and performance of these new quantitative methods are assessed. ASTM correspondence is attained using a mixed-mode calibration, using primary reference standards to anchor the calibration, supplemented by representative sample lubricants analyzed by ASTM procedures. A partial least squares calibration is devised by combining primary acid/base reference standards and representative samples, focusing on the main spectral stoichiometric response with chemometrics assisting in accounting for matrix variability. FTIR(AN/BN) methodology is precise, accurate, and free of most interference that affects ASTM D664 and D4739 results. Extensive side-by-side operational runs produced normally distributed differences with mean differences close to zero and standard deviations of 0.18 and 0.26 mg KOH/g, respectively. Statistically, the FTIR methods are a direct match to the ASTM methods, with superior performance in terms of analytical throughput, preparation time, and solvent use. FTIR(AN/BN) analysis is a viable, significant advance for in-service lubricant analysis, providing an economic means of trending samples instead of tedious and expensive conventional ASTM(AN/BN) procedures. © 2014 Society for Laboratory Automation and Screening.

Summary: Update to ASTM guide E 1523 to charge control and charge referencing techniques in x-ray photoelectron spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baer, D.R.

2005-05-01

An updated version of the American Society for Testing and Materials (ASTM) guide E 1523 to the methods to charge control and charge referencing techniques in x-ray photoelectron spectroscopy has been released by ASTM [Annual Book of ASTM Standards Surface Analysis (American Society for Testing and Materials, West Conshohocken, PA, 2004), Vol. 03.06]. The guide is meant to acquaint x-ray photoelectron spectroscopy (XPS) users with the various charge control and charge referencing techniques that are and have been used in the acquisition and interpretation of XPS data from surfaces of insulating specimens. The current guide has been expanded to includemore » new references as well as recommendations for reporting information on charge control and charge referencing. The previous version of the document had been published in 1997 [D. R. Baer and K. D. Bomben, J. Vac. Sci. Technol. A 16, 754 (1998)].« less

Microbial ranking of porous packaging materials (exposure chamber method), ASTM method: collaborative study.

PubMed

Placencia, A M; Peeler, J T

1999-01-01

A collaborative study involving 11 laboratories was conducted to measure the microbial barrier effectiveness of porous medical packaging. Two randomly cut samples from each of 6 commercially available porous materials and one positive and one negative control were tested by one operator in each of 11 laboratories. Microbial barrier effectiveness was measured in terms of logarithm reduction value (LRV), which reflects the log10 microbial penetration of the material being tested. The logarithm of the final concentration is subtracted from that of the initial concentration to obtain the LRV. Thus the higher the LRV, the better the barrier. Repeatability standard deviations ranged from 6.42 to 16.40; reproducibility standard deviations ranged from 15.50 to 22.70. Materials B(53), C(50), D(CT), and E(45MF) differ significantly from the positive control. The microbial ranking of porous packaging materials (exposure chamber method), ASTM method, has been adopted First Action by AOAC INTERNATIONAL.

46 CFR 170.015 - Incorporation by reference.

Code of Federal Regulations, 2010 CFR

2010-10-01

... the sources listed below. (b) ASTM International (formerly American Society for Testing and Materials) (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959: (1) ASTM F 1196-00, Standard Specification for Sliding Watertight Door Assemblies (2000) (“ASTM F 1196”), 170.270; and (2) ASTM F 1197-00...

Fuel and Fuel System Materials Compatibility Test Program for A JP-8+100 Fuel Additive. Volume 1: Thermal Stability Additive Package BetzDearborn Spec Aid(Registered) 8Q462

DTIC Science & Technology

2001-10-01

SAE Rings, Sealing, Butadiene-Acrylonitrile ( NBR ), Rubber Fuel and Low Temperature Resistant 60 - 70 MIL-R-83248C Rubber , Fluorocarbon...KAPTON/TEFLON (COMPOSITE) WIRE I.I.10 34 VI. REFERENCE DOCUMENTS Non-Metallics MIL-HDBK-149B Military Standardization Hand Book Rubber ...ASTM D-1414 Standard Test Methods for Rubber O-Rings ASTM D-412 Type II Standard Test Methods for Vulcanized Rubber and Thermoplastic

49 CFR 179.300-7 - Materials.

Code of Federal Regulations, 2010 CFR

2010-10-01

... carbon steel must not exceed 0.31 percent, although the individual ASTM specification may allow for a... (longitudinal) (minimum) ASTM A 240/A 240M type 304 75,000 25 ASTM A 240/A 240M type 304L 70,000 25 ASTM A 240/A 240M type 316 75,000 25 ASTM A 240/A 240M type 316L 70,000 25 ASTM A 240/A 240M type 321 75,000 25 ASTM...

10 CFR 431.263 - Materials incorporated by reference.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Society for Testing and Materials (ASTM) Standard F2324-03, “Standard Test Method for Prerinse Spray..., Forrestal Building, Room 1J-018 (Resource Room of the Building Technologies Program), 1000 Independence...

10 CFR 431.263 - Materials incorporated by reference.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Society for Testing and Materials (ASTM) Standard F2324-03, “Standard Test Method for Prerinse Spray..., Forrestal Building, Room 1J-018 (Resource Room of the Building Technologies Program), 1000 Independence...

Effectiveness of Cool Roof Coatings with Ceramic Particles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brehob, Ellen G; Desjarlais, Andre Omer; Atchley, Jerald Allen

2011-01-01

Liquid applied coatings promoted as cool roof coatings, including several with ceramic particles, were tested at Oak Ridge National Laboratory (ORNL), Oak Ridge, Tenn., for the purpose of quantifying their thermal performances. Solar reflectance measurements were made for new samples and aged samples using a portable reflectometer (ASTM C1549, Standard Test Method for Determination of Solar Reflectance Near Ambient Temperature Using a Portable Solar Reflectometer) and for new samples using the integrating spheres method (ASTM E903, Standard Test Method for Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating Spheres). Thermal emittance was measured for the new samples using amore » portable emissometer (ASTM C1371, Standard Test Method for Determination of Emittance of Materials Near Room 1 Proceedings of the 2011 International Roofing Symposium Temperature Using Portable Emissometers). Thermal conductivity of the coatings was measured using a FOX 304 heat flow meter (ASTM C518, Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus). The surface properties of the cool roof coatings had higher solar reflectance than the reference black and white material, but there were no significant differences among coatings with and without ceramics. The coatings were applied to EPDM (ethylene propylene diene monomer) membranes and installed on the Roof Thermal Research Apparatus (RTRA), an instrumented facility at ORNL for testing roofs. Roof temperatures and heat flux through the roof were obtained for a year of exposure in east Tennessee. The field tests showed significant reduction in cooling required compared with the black reference roof (~80 percent) and a modest reduction in cooling compared with the white reference roof (~33 percent). The coating material with the highest solar reflectivity (no ceramic particles) demonstrated the best overall thermal performance (combination of reducing the cooling load cost and not incurring a large heating penalty cost) and suggests solar reflectivity is the significant characteristic for selecting cool roof coatings.« less

46 CFR 163.003-3 - ASTM standard.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false ASTM standard. 163.003-3 Section 163.003-3 Shipping...: SPECIFICATIONS AND APPROVAL CONSTRUCTION Pilot Ladder § 163.003-3 ASTM standard. The following standard of the American Society for Testing and Materials (ASTM) is incorporated by reference into this subpart: ASTM D...

40 CFR 63.14 - Incorporations by reference.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Testing and Materials (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428... (Reapproved 2010), Standard Test Method for Water in Petroleum Products and Bituminous Materials by...-09 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter...

7 CFR 3201.7 - Determining biobased content.

Code of Federal Regulations, 2014 CFR

2014-01-01

... International Radioisotope Standard Method D 6866. ASTM International Radioisotope Standard Method D 6866... the weight (mass) of the total organic carbon in the material or product. (d) Products with the same...

46 CFR 54.01-1 - Incorporation by reference.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) ASTM International (formerly American Society for Testing and Materials) (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959: (1) ASTM A 20/A 20M-97a, Standard Specification for General Requirements for Steel Plates for Pressure Vessels (“ASTM A 20”), 54.05-10; 54.25-10; (2) ASTM A 203/A 203M-97...

40 CFR 91.6 - Reference materials.

Code of Federal Regulations, 2014 CFR

2014-07-01

... EMISSIONS FROM MARINE SPARK-IGNITION ENGINES General § 91.6 Reference materials. (a) Incorporation by... the Research Method Appendix A to Subpart D. ASTM D2700-92: Standard Test Method for Knock... 40 CFR part 91 reference SAE J1228/ISO 8665 November 1991 Small Craft-Marine Propulsion Engine and...

40 CFR 91.6 - Reference materials.

Code of Federal Regulations, 2013 CFR

2013-07-01

... EMISSIONS FROM MARINE SPARK-IGNITION ENGINES General § 91.6 Reference materials. (a) Incorporation by... the Research Method Appendix A to Subpart D. ASTM D2700-92: Standard Test Method for Knock... 40 CFR part 91 reference SAE J1228/ISO 8665 November 1991 Small Craft-Marine Propulsion Engine and...

40 CFR 91.6 - Reference materials.

Code of Federal Regulations, 2012 CFR

2012-07-01

... EMISSIONS FROM MARINE SPARK-IGNITION ENGINES General § 91.6 Reference materials. (a) Incorporation by... the Research Method Appendix A to Subpart D. ASTM D2700-92: Standard Test Method for Knock... 40 CFR part 91 reference SAE J1228/ISO 8665 November 1991 Small Craft-Marine Propulsion Engine and...

46 CFR 164.015-1 - Applicable specifications and standards.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL MATERIALS Plastic Foam, Unicellular, Buoyant, Sheet... following specification and standard, of the issue in effect on the date the plastic foam material is...) ASTM D4986-98, Standard Test Method for Horizontal Burning Characteristics of Cellular Polymeric...

Automatic Detection of Pearlite Spheroidization Grade of Steel Using Optical Metallography.

PubMed

Chen, Naichao; Chen, Yingchao; Ai, Jun; Ren, Jianxin; Zhu, Rui; Ma, Xingchi; Han, Jun; Ma, Qingqian

2016-02-01

To eliminate the effect of subjective factors during manually determining the pearlite spheroidization grade of steel by analysis of optical metallography images, a novel method combining image mining and artificial neural networks (ANN) is proposed. The four co-occurrence matrices of angular second moment, contrast, correlation, and entropy are adopted to objectively characterize the images. ANN is employed to establish a mathematical model between the four co-occurrence matrices and the corresponding spheroidization grade. Three materials used in coal-fired power plants (ASTM A315-B steel, ASTM A335-P12 steel, and ASTM A355-P11 steel) were selected as the samples to test the validity of our proposed method. The results indicate that the accuracies of the calculated spheroidization grades reach 99.05, 95.46, and 93.63%, respectively. Hence, our newly proposed method is adequate for automatically detecting the pearlite spheroidization grade of steel using optical metallography.

Kinetics and microscopic processes of long term fracture in polyethylene piping materials

NASA Astrophysics Data System (ADS)

Brown, N.; Lu, X.

1992-07-01

The report contains 9 completed works as follows: The Dependence of Slow Crack Growth in a Polyethylene Copolymer on Testing Temperature and Morphology; A Test of Slow Crack Growth Failure of PE Under Constant Load; Effect of Annealing on Slow Crack Growth in an Ethylene-Hexene Copolymer; The Fundamental Material Parameters that Govern Slow Crack Growth in Linear Polyethylene; Slow Crack Growth in Blends of HDPE and UHMWPE; The Mechanism of Fatigue Failure in a Polyethylene Copolymer; PENT Quality Control Test for PE Gas Pipes and Resins; International Round Robin Study of a Fatigue Test Approach to the Ranking of Polyethylene Pipe Material; and Proposed ASTM Specification for ASTM F17.40 Test Methods Committee.

40 CFR 90.7 - Reference materials.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Appendix A to subpart D, Table 3. ASTM D2699-92: Standard Test Method for Knock Characteristics of Motor... Knock Characteristics of Motor and Aviation Fuels by the Motor Method Appendix A to subpart D, Table 3...

40 CFR 90.7 - Reference materials.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Appendix A to subpart D, Table 3. ASTM D2699-92: Standard Test Method for Knock Characteristics of Motor... Knock Characteristics of Motor and Aviation Fuels by the Motor Method Appendix A to subpart D, Table 3...

46 CFR 174.007 - Incorporation by reference.

Code of Federal Regulations, 2010 CFR

2010-10-01

... are: American Society for Testing and Materials (ASTM) 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. ASTM F 1196-94, Standard Specification for Sliding Watertight Door Assemblies—174.100 ASTM F...

Test Standard Developed for Determining the Slow Crack Growth of Advanced Ceramics at Ambient Temperature

NASA Technical Reports Server (NTRS)

Choi, Sung R.; Salem, Jonathan A.

1998-01-01

The service life of structural ceramic components is often limited by the process of slow crack growth. Therefore, it is important to develop an appropriate testing methodology for accurately determining the slow crack growth design parameters necessary for component life prediction. In addition, an appropriate test methodology can be used to determine the influences of component processing variables and composition on the slow crack growth and strength behavior of newly developed materials, thus allowing the component process to be tailored and optimized to specific needs. At the NASA Lewis Research Center, work to develop a standard test method to determine the slow crack growth parameters of advanced ceramics was initiated by the authors in early 1994 in the C 28 (Advanced Ceramics) committee of the American Society for Testing and Materials (ASTM). After about 2 years of required balloting, the draft written by the authors was approved and established as a new ASTM test standard: ASTM C 1368-97, Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Ambient Temperature. Briefly, the test method uses constant stress-rate testing to determine strengths as a function of stress rate at ambient temperature. Strengths are measured in a routine manner at four or more stress rates by applying constant displacement or loading rates. The slow crack growth parameters required for design are then estimated from a relationship between strength and stress rate. This new standard will be published in the Annual Book of ASTM Standards, Vol. 15.01, in 1998. Currently, a companion draft ASTM standard for determination of the slow crack growth parameters of advanced ceramics at elevated temperatures is being prepared by the authors and will be presented to the committee by the middle of 1998. Consequently, Lewis will maintain an active leadership role in advanced ceramics standardization within ASTM. In addition, the authors have been and are involved with several international standardization organizations including the Versailles Project on Advanced Materials and Standards (VAMAS), the International Energy Agency (IEA), and the International Organization for Standardization (ISO). The associated standardization activities involve fracture toughness, strength, elastic modulus, and the machining of advanced ceramics.

An Improved Approach for Analyzing the Oxygen Compatibility of Solvents and other Oxygen-Flammable Materials for Use in Oxygen Systems

NASA Technical Reports Server (NTRS)

Harper, Susan A.; Juarez, Alfredo; Peralta, Stephen F.; Stoltzfus, Joel; Arpin, Christina Pina; Beeson, Harold D.

2016-01-01

Solvents used to clean oxygen system components must be assessed for oxygen compatibility, as incompatible residue or fluid inadvertently left behind within an oxygen system can pose a flammability risk. The most recent approach focused on solvent ignition susceptibility to assess the flammability risk associated with these materials. Previous evaluations included Ambient Pressure Liquid Oxygen (LOX) Mechanical Impact Testing (ASTM G86) and Autogenous Ignition Temperature (AIT) Testing (ASTM G72). The goal in this approach was to identify a solvent material that was not flammable in oxygen. As environmental policies restrict the available options of acceptable solvents, it has proven difficult to identify one that is not flammable in oxygen. A more rigorous oxygen compatibility approach is needed in an effort to select a new solvent for NASA applications. NASA White Sands Test Facility proposed an approach that acknowledges oxygen flammability, yet selects solvent materials based on their relative oxygen compatibility ranking, similar to that described in ASTM G63-99. Solvents are selected based on their ranking with respect to minimal ignition susceptibility, damage and propagation potential, as well as their relative ranking when compared with other solvent materials that are successfully used in oxygen systems. Test methods used in this approach included ASTM G86 (Ambient Pressure LOX Mechanical Impact Testing and Pressurized Gaseous Oxygen (GOX) Mechanical Impact Testing), ASTM G72 (AIT Testing), and ASTM D240 (Heat of Combustion (HOC) Testing). Only four solvents were tested through the full battery of tests for evaluation of oxygen compatibility: AK-225G as a baseline comparison, Solstice PF, L-14780, and Vertrel MCA. Baseline solvent AK-225G exhibited the lowest HOC and highest AIT of solvents tested. Nonetheless, Solstice PF, L-14780, and Vertrel MCA HOCs all fell well within the range of properties that are associated with proven oxygen system materials. Tested AITs for these solvents fell only slightly lower than the AIT for the proven AK-225G solvent. Based on these comparisons in which solvents exhibited properties within those ranges seen with proven oxygen system materials, it is believed that Solstice PF, L-14780, and Vertrel MCA would perform well with respect to oxygen compatibility.

47 CFR 95.1509 - ASTM E2213-03 DSRC Standard.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false ASTM E2213-03 DSRC Standard. 95.1509 Section 95... ASTM E2213-03 DSRC Standard. On-Board Units operating in the 5850-5925 MHz band shall comply with the... Materials (ASTM) E2213-03, Standard Specification for Telecommunications and Information Exchange Between...

46 CFR 105.01-3 - Incorporation by reference.

Code of Federal Regulations, 2010 CFR

2010-10-01

... from the sources listed below. (b) American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, telephone 610-832-9585, http://www.astm.org. (1) ASTM D 323-94...

46 CFR 163.003-3 - ASTM standard.

Code of Federal Regulations, 2011 CFR

2011-10-01

... American Society for Testing and Materials (ASTM) is incorporated by reference into this subpart: ASTM D... Society at 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. [USCG-1999-5151, 64 FR 67185, Dec. 1...

Interlaboratory evaluation of a standardized inductively coupled plasma mass spectrometry method for the determination of trace beryllium in air filter samples.

PubMed

Ashley, Kevin; Brisson, Michael J; Howe, Alan M; Bartley, David L

2009-12-01

A collaborative interlaboratory evaluation of a newly standardized inductively coupled plasma mass spectrometry (ICP-MS) method for determining trace beryllium in workplace air samples was carried out toward fulfillment of method validation requirements for ASTM International voluntary consensus standard test methods. The interlaboratory study (ILS) was performed in accordance with an applicable ASTM International standard practice, ASTM E691, which describes statistical procedures for investigating interlaboratory precision. Uncertainty was also estimated in accordance with ASTM D7440, which applies the International Organization for Standardization Guide to the Expression of Uncertainty in Measurement to air quality measurements. Performance evaluation materials (PEMs) used consisted of 37 mm diameter mixed cellulose ester filters that were spiked with beryllium at levels of 0.025 (low loading), 0.5 (medium loading), and 10 (high loading) microg Be/filter; these spiked filters were prepared by a contract laboratory. Participating laboratories were recruited from a pool of over 50 invitees; ultimately, 20 laboratories from Europe, North America, and Asia submitted ILS results. Triplicates of each PEM (blanks plus the three different loading levels) were conveyed to each volunteer laboratory, along with a copy of the draft standard test method that each participant was asked to follow; spiking levels were unknown to the participants. The laboratories were requested to prepare the PEMs by one of three sample preparation procedures (hotplate or microwave digestion or hotblock extraction) that were described in the draft standard. Participants were then asked to analyze aliquots of the prepared samples by ICP-MS and to report their data in units of mu g Be/filter sample. Interlaboratory precision estimates from participating laboratories, computed in accordance with ASTM E691, were 0.165, 0.108, and 0.151 (relative standard deviation) for the PEMs spiked at 0.025, 0.5, and 10 microg Be/filter, respectively. Overall recoveries were 93.2%, 102%, and 80.6% for the low, medium, and high beryllium loadings, respectively. Expanded uncertainty estimates for interlaboratory analysis of low, medium, and high beryllium loadings, calculated in accordance with ASTM D7440, were 18.8%, 19.8%, and 24.4%, respectively. These figures of merit support promulgation of the analytical procedure as an ASTM International standard test method, ASTM D7439.

40 CFR 265.314 - Special requirements for bulk and containerized liquids.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (iii) Mixtures of these non-bio-degrad-a-ble materials. (2) Tests for non-bio-degrad-a-ble sorbents. (i) The sorbent material is determined to be non-bio-degrad-a-ble under ASTM Method G21-70 (1984a...

40 CFR 265.314 - Special requirements for bulk and containerized liquids.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (iii) Mixtures of these non-bio-degrad-a-ble materials. (2) Tests for non-bio-degrad-a-ble sorbents. (i) The sorbent material is determined to be non-bio-degrad-a-ble under ASTM Method G21-70 (1984a...

40 CFR 265.314 - Special requirements for bulk and containerized liquids.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (iii) Mixtures of these non-bio-degrad-a-ble materials. (2) Tests for non-bio-degrad-a-ble sorbents. (i) The sorbent material is determined to be non-bio-degrad-a-ble under ASTM Method G21-70 (1984a...

40 CFR 265.314 - Special requirements for bulk and containerized liquids.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (iii) Mixtures of these non-bio-degrad-a-ble materials. (2) Tests for non-bio-degrad-a-ble sorbents. (i) The sorbent material is determined to be non-bio-degrad-a-ble under ASTM Method G21-70 (1984a...

A simple method for the measurement of reflective foil emissivity

NASA Astrophysics Data System (ADS)

Ballico, M. J.; van der Ham, E. W. M.

2013-09-01

Reflective metal foil is widely used to reduce radiative heat transfer within the roof space of buildings. Such foils are typically mass-produced by vapor-deposition of a thin metallic coating onto a variety of substrates, ranging from plastic-coated reinforced paper to "bubble-wrap". Although the emissivity of such surfaces is almost negligible in the thermal infrared, typically less than 0.03, an insufficiently thick metal coating, or organic contamination of the surface, can significantly increase this value. To ensure that the quality of the installed insulation is satisfactory, Australian building code AS/NZS 4201.5:1994 requires a practical agreed method for measurement of the emissivity, and the standard ASTM-E408 is implied. Unfortunately this standard is not a "primary method" and requires the use of specified expensive apparatus and calibrated reference materials. At NMIA we have developed a simple primary technique, based on an apparatus to thermally modulate the sample and record the apparent modulation in infra-red radiance with commercially available radiation thermometers. The method achieves an absolute accuracy in the emissivity of approximately 0.004 (k=2). This paper theoretically analyses the equivalence between the thermal emissivity measured in this manner, the effective thermal emissivity in application, and the apparent emissivity measured in accordance with ASTM-E408.

A simple method for the measurement of reflective foil emissivity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ballico, M. J.; Ham, E. W. M. van der

Reflective metal foil is widely used to reduce radiative heat transfer within the roof space of buildings. Such foils are typically mass-produced by vapor-deposition of a thin metallic coating onto a variety of substrates, ranging from plastic-coated reinforced paper to 'bubble-wrap'. Although the emissivity of such surfaces is almost negligible in the thermal infrared, typically less than 0.03, an insufficiently thick metal coating, or organic contamination of the surface, can significantly increase this value. To ensure that the quality of the installed insulation is satisfactory, Australian building code AS/NZS 4201.5:1994 requires a practical agreed method for measurement of the emissivity,more » and the standard ASTM-E408 is implied. Unfortunately this standard is not a 'primary method' and requires the use of specified expensive apparatus and calibrated reference materials. At NMIA we have developed a simple primary technique, based on an apparatus to thermally modulate the sample and record the apparent modulation in infra-red radiance with commercially available radiation thermometers. The method achieves an absolute accuracy in the emissivity of approximately 0.004 (k=2). This paper theoretically analyses the equivalence between the thermal emissivity measured in this manner, the effective thermal emissivity in application, and the apparent emissivity measured in accordance with ASTM-E408.« less

40 CFR 63.5719 - How do I conduct a performance test?

Code of Federal Regulations, 2011 CFR

2011-07-01

... appendix A to 40 CFR part 60, as appropriate, to select the sampling sites. (2) Use Method 2, 2A, 2C, 2D... emissions. (4) You may use American Society for Testing and Materials (ASTM) D6420-99 (available for... parts being made and material application methods. The production conditions during the test must also...

49 CFR 179.220-25 - Stamping.

Code of Federal Regulations, 2010 CFR

2010-10-01

...: Material ASTM A240-316L. Shell thickness Shell 0.167 in. Head thickness Head 0.150 in. Tank builders initials ABC. Date of original test 00-0000. Outer shell: Material ASTM A285-C. Tank builders initials WYZ...

40 CFR 60.41b - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Society of Testing and Materials in ASTM D3699 (incorporated by reference, see § 60.17), biodiesel as... § 60.17), or biodiesel blends as defined by the American Society of Testing and Materials in ASTM D7467...

40 CFR 60.41b - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Society of Testing and Materials in ASTM D3699 (incorporated by reference, see § 60.17), biodiesel as... § 60.17), or biodiesel blends as defined by the American Society of Testing and Materials in ASTM D7467...

40 CFR 60.41b - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Society of Testing and Materials in ASTM D3699 (incorporated by reference, see § 60.17), biodiesel as... § 60.17), or biodiesel blends as defined by the American Society of Testing and Materials in ASTM D7467...

76 FR 78614 - Welded ASTM A-312 Stainless Steel Pipe From South Korea and Taiwan: Continuation of Antidumping...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-19

... standards and specifications set forth by the American Society for Testing and Materials (ASTM) for the... stainless steel flat-rolled products into a tubular configuration and welding along the seam. Welded ASTM A...

On-Board Monitoring of Engine Oil

DTIC Science & Technology

2011-04-01

Viscosity of Transparent and Opaque Liquids at 40°C Infracal Soot Meter Karl Fischer Titration ASTM D 664 Standard Test Method for Acid Number of... methods involve potentiometric and colorimetric titrations, respectively. For both tests, a titration solvent is prepared and added to the oil. The...ASTM D 2896 and ASTM D 4739 [17]. Both methods involve potentiometric titrations. ASTM D 2896 uses a stronger acid and more polar solvent than ASTM D

On the Interplay Between Adhesion Strength and Tensile Properties of Thermal Spray Coated Laminates—Part II: Low-Velocity Thermal Spray Coatings

NASA Astrophysics Data System (ADS)

Luo, Xiaotao; Smith, Gregory M.; Sampath, Sanjay

2018-02-01

In this two-part study, uniaxial tensile testing was used to evaluate coating/substrate bonding and compared with traditional ASTM C633 bond pull test results for thermal spray (TS) coated steel laminates. In Part I, the rationale, methodology, and applicability of the test to high-velocity TS coatings were demonstrated. In this Part II, the method was investigated for low-velocity TS processes (air plasma spray and arc spray) on equivalent materials. Ni and Ni-5wt.%Al coatings were deposited on steel substrates with three different roughness levels and tested using both uniaxial tensile and ASTM C633 methods. The results indicate the uniaxial tensile approach provides useful information about the nature of the coating/substrate bonding and goes beyond the traditional bond pull test in providing insightful information on the load sharing processes across the interface. Additionally, this proposed methodology alleviates some of the longstanding shortcomings and potentially reduces error associated with the traditional ASTM C633 test. The mechanisms governing the load transfer between the substrate and the coating were investigated, and the influence of Al in the coating material evaluated.

40 CFR 98.7 - What standardized methods are incorporated by reference into this part?

Code of Federal Regulations, 2012 CFR

2012-07-01

....astm.org. (1) ASTM C25-06 Standard Test Method for Chemical Analysis of Limestone, Quicklime, and....194(c), and § 98.334(b). (2) ASTM C114-09 Standard Test Methods for Chemical Analysis of Hydraulic... approved for § 98.6. (4) ASTM D240-02 (Reapproved 2007) Standard Test Method for Heat of Combustion of...

40 CFR 98.7 - What standardized methods are incorporated by reference into this part?

Code of Federal Regulations, 2013 CFR

2013-07-01

....astm.org. (1) ASTM C25-06 Standard Test Method for Chemical Analysis of Limestone, Quicklime, and....194(c), and § 98.334(b). (2) ASTM C114-09 Standard Test Methods for Chemical Analysis of Hydraulic... approved for § 98.6. (4) ASTM D240-02 (Reapproved 2007) Standard Test Method for Heat of Combustion of...

76 FR 2056 - Incorporation of Revised ASTM Standards That Provide Flexibility in the Use of Alternatives to...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-12

... Sulfur in Petroleum Products (General Bomb Method); ASTM D2622-98, Standard Test Method for Sulfur in...; ASTM D240-00, Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb... Liquid Hydrocarbon Fuels by Bomb Calorimeter, ASTM D4809-00, Standard Test Method for Heat of Combustion...

40 CFR 63.5719 - How do I conduct a performance test?

Code of Federal Regulations, 2012 CFR

2012-07-01

... sampling sites. (2) Use Method 2, 2A, 2C, 2D, 2F or 2G of appendix A to 40 CFR part 60, as appropriate, to... organic HAP emissions. (4) You may use American Society for Testing and Materials (ASTM) D6420-99... respect to the types of parts being made and material application methods. The production conditions...

40 CFR 63.5719 - How do I conduct a performance test?

Code of Federal Regulations, 2014 CFR

2014-07-01

... sampling sites. (2) Use Method 2, 2A, 2C, 2D, 2F or 2G of appendix A to 40 CFR part 60, as appropriate, to... organic HAP emissions. (4) You may use American Society for Testing and Materials (ASTM) D6420-99... respect to the types of parts being made and material application methods. The production conditions...

40 CFR 63.5719 - How do I conduct a performance test?

Code of Federal Regulations, 2013 CFR

2013-07-01

... sampling sites. (2) Use Method 2, 2A, 2C, 2D, 2F or 2G of appendix A to 40 CFR part 60, as appropriate, to... organic HAP emissions. (4) You may use American Society for Testing and Materials (ASTM) D6420-99... respect to the types of parts being made and material application methods. The production conditions...

40 CFR 89.6 - Reference materials.

Code of Federal Regulations, 2014 CFR

2014-07-01

... July 1, 2009), Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (the Calculation of Dynamic Viscosity), IBR approved for appendix A to subpart D. (6) ASTM D613-95, Standard Test...

40 CFR 89.6 - Reference materials.

Code of Federal Regulations, 2012 CFR

2012-07-01

... July 1, 2009), Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (the Calculation of Dynamic Viscosity), IBR approved for appendix A to subpart D. (6) ASTM D613-95, Standard Test...

40 CFR 89.6 - Reference materials.

Code of Federal Regulations, 2013 CFR

2013-07-01

... July 1, 2009), Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (the Calculation of Dynamic Viscosity), IBR approved for appendix A to subpart D. (6) ASTM D613-95, Standard Test...

Polyhydroxyalkanoates (PHA) Bioplastic Packaging Materials

DTIC Science & Technology

2010-05-01

FINAL REPORT Polyhydroxyalkanoates (PHA) Bioplastic Packaging Materials SERDP Project WP-1478 MAY 2010 Dr.Chris Schwier Metabolix...biopolymer, biodegradable, polyhydroxyalkanoate 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT 18. NUMBER OF PAGES 19a. NAME OF...Acronyms and Definitions ASTM – American Society of Test Methods ISO – International Standardization Organization PHA – Polyhydroxyalkanoates

46 CFR 114.600 - Incorporation by reference.

Code of Federal Regulations, 2011 CFR

2011-10-01

... supplement—Safety Glazing Materials For Glazing Motor Vehicles Operating on Land Highways 116.1030 American... Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position... Burning Characteristics of Building Materials 116.405; 116.422; 116.423 ASTM E 648-97, Standard Test...

An Elementary Overview of the Selection of Materials for Service in Oxygen-Enriched Environments

NASA Technical Reports Server (NTRS)

Davis, Samuel Eddie

2012-01-01

The process for selecting materials for use in oxygen or oxygen-enriched environments is one that continues to be investigated by many industries due to the importance to those industries of oxygen systems. There are several excellent resources available to assist oxygen systems design engineers and end-users, with the most comprehensive being ASTM MNL-36, Safe Use of Oxygen and Oxygen Systems: Handbook for Design, Operation and Maintenance, 2nd Edition. ASTM also makes available several standards for oxygen systems. However, the ASTM publications are extremely detailed, and typically designed for professionals who already possess a working knowledge of oxygen systems. No notable resource exists, whether an ASTM or other organizational publication, which can be used to educate engineers or technicians who have no prior knowledge of the nuances of oxygen system design and safety. This paper will fill the void for information needed by organizations that design or operate oxygen systems. The information in this paper is not new information, but is a concise and easily understood summary of selecting materials for oxygen systems. This paper will serve well as an employee s first introduction to oxygen system materials selection, and probably the employee s first introduction to ASTM.

Vapor Pressure Data and Analysis for Selected HD Decomposition Products: 1,4-Thioxane, Divinyl Sulfoxide, Chloroethyl Acetylsulfide, and 1,4-Dithiane

DTIC Science & Technology

2018-06-01

decomposition products from bis-(2-chloroethyl) sulfide (HD). These data were measured using an ASTM International method that is based on differential...2.1 Materials and Method ........................................................................................2 2.2 Data Analysis...and Method The source and purity of the materials studied are listed in Table 1. Table 1. Sample Information for Title Compounds Compound

CCR+: Metadata Based Extended Personal Health Record Data Model Interoperable with the ASTM CCR Standard.

PubMed

Park, Yu Rang; Yoon, Young Jo; Jang, Tae Hun; Seo, Hwa Jeong; Kim, Ju Han

2014-01-01

Extension of the standard model while retaining compliance with it is a challenging issue because there is currently no method for semantically or syntactically verifying an extended data model. A metadata-based extended model, named CCR+, was designed and implemented to achieve interoperability between standard and extended models. Furthermore, a multilayered validation method was devised to validate the standard and extended models. The American Society for Testing and Materials (ASTM) Community Care Record (CCR) standard was selected to evaluate the CCR+ model; two CCR and one CCR+ XML files were evaluated. In total, 188 metadata were extracted from the ASTM CCR standard; these metadata are semantically interconnected and registered in the metadata registry. An extended-data-model-specific validation file was generated from these metadata. This file can be used in a smartphone application (Health Avatar CCR+) as a part of a multilayered validation. The new CCR+ model was successfully evaluated via a patient-centric exchange scenario involving multiple hospitals, with the results supporting both syntactic and semantic interoperability between the standard CCR and extended, CCR+, model. A feasible method for delivering an extended model that complies with the standard model is presented herein. There is a great need to extend static standard models such as the ASTM CCR in various domains: the methods presented here represent an important reference for achieving interoperability between standard and extended models.

30 CFR 75.301 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-warning fire detection systems using newer technology that provides equal or greater protection, as... be purchased from the American Society for Testing Materials (ASTM), 1916 Race Street, Philadelphia..., copies of the document can be purchased from the American Society for Testing Materials (ASTM), 100 Barr...

29 CFR Appendix A to Subpart Q of... - References to subpart Q of Part 1926

Code of Federal Regulations, 2010 CFR

2010-07-01

... (ASTM C39-86). • Standard Test Method for Making and Curing Concrete Test Specimens in the Field (ASTM C31-85). • Standard Test Method for Penetration Resistance of Hardened Concrete (ASTM C803-82... (ASTM C873-85). • Standard Method for Developing Early Age Compressive Test Values and Projecting Later...

Improved ASTM G72 Test Method for Ensuring Adequate Fuel-to-Oxidizer Ratios

NASA Technical Reports Server (NTRS)

Juarez, Alfredo; Harper, Susana A.

2016-01-01

The ASTM G72/G72M-15 Standard Test Method for Autogenous Ignition Temperature of Liquids and Solids in a High-Pressure Oxygen-Enriched Environment is currently used to evaluate materials for the ignition susceptibility driven by exposure to external heat in an enriched oxygen environment. Testing performed on highly volatile liquids such as cleaning solvents has proven problematic due to inconsistent test results (non-ignitions). Non-ignition results can be misinterpreted as favorable oxygen compatibility, although they are more likely associated with inadequate fuel-to-oxidizer ratios. Forced evaporation during purging and inadequate sample size were identified as two potential causes for inadequate available sample material during testing. In an effort to maintain adequate fuel-to-oxidizer ratios within the reaction vessel during test, several parameters were considered, including sample size, pretest sample chilling, pretest purging, and test pressure. Tests on a variety of solvents exhibiting a range of volatilities are presented in this paper. A proposed improvement to the standard test protocol as a result of this evaluation is also presented. Execution of the final proposed improved test protocol outlines an incremental step method of determining optimal conditions using increased sample sizes while considering test system safety limits. The proposed improved test method increases confidence in results obtained by utilizing the ASTM G72 autogenous ignition temperature test method and can aid in the oxygen compatibility assessment of highly volatile liquids and other conditions that may lead to false non-ignition results.

ASTM and other specifications and classifications for petroleum products and lubricants. Fifth edition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1989-01-01

This book includes specifications and classifications from ASTM committees on paint and related coatings and materials; road and paving materials; wood; roofing, waterproofing and bituminous materials; rubber; soaps and other detergents; aromatic hydrocarbons and related chemicals; and electrical insulating liquids and gases. Also included are several related, important specifications and classifications from other organizations.

CCR+: Metadata Based Extended Personal Health Record Data Model Interoperable with the ASTM CCR Standard

PubMed Central

Park, Yu Rang; Yoon, Young Jo; Jang, Tae Hun; Seo, Hwa Jeong

2014-01-01

Objectives Extension of the standard model while retaining compliance with it is a challenging issue because there is currently no method for semantically or syntactically verifying an extended data model. A metadata-based extended model, named CCR+, was designed and implemented to achieve interoperability between standard and extended models. Methods Furthermore, a multilayered validation method was devised to validate the standard and extended models. The American Society for Testing and Materials (ASTM) Community Care Record (CCR) standard was selected to evaluate the CCR+ model; two CCR and one CCR+ XML files were evaluated. Results In total, 188 metadata were extracted from the ASTM CCR standard; these metadata are semantically interconnected and registered in the metadata registry. An extended-data-model-specific validation file was generated from these metadata. This file can be used in a smartphone application (Health Avatar CCR+) as a part of a multilayered validation. The new CCR+ model was successfully evaluated via a patient-centric exchange scenario involving multiple hospitals, with the results supporting both syntactic and semantic interoperability between the standard CCR and extended, CCR+, model. Conclusions A feasible method for delivering an extended model that complies with the standard model is presented herein. There is a great need to extend static standard models such as the ASTM CCR in various domains: the methods presented here represent an important reference for achieving interoperability between standard and extended models. PMID:24627817

40 CFR 761.19 - References.

Code of Federal Regulations, 2014 CFR

2014-07-01

... approved materials are also available for inspection at the National Archives and Records Administration...://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. In addition, these... Bomb Method), IBR approved for § 761.71. (3) ASTM D240-87, Standard Test Method for Heat of Combustion...

40 CFR 761.19 - References.

Code of Federal Regulations, 2012 CFR

2012-07-01

... approved materials are also available for inspection at the National Archives and Records Administration...://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. In addition, these... Bomb Method), IBR approved for § 761.71. (3) ASTM D240-87, Standard Test Method for Heat of Combustion...

40 CFR 761.19 - References.

Code of Federal Regulations, 2013 CFR

2013-07-01

... approved materials are also available for inspection at the National Archives and Records Administration...://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. In addition, these... Bomb Method), IBR approved for § 761.71. (3) ASTM D240-87, Standard Test Method for Heat of Combustion...

40 CFR 80.1468 - Incorporation by reference.

Code of Federal Regulations, 2010 CFR

2010-07-01

....astm.org). (1) ASTM D 1250-08 (“ASTM D 1250”), Standard Guide for Use of the Petroleum Measurement Tables, Approved 2008; IBR approved for § 80.1426(f)(8)(ii)(B). (2) ASTM D 4442-07 (“ASTM D 4442... 2007; IBR approved for § 80.1426(f)(7)(v)(B). (3) ASTM D 4444-08 (“ASTM D 4444”), Standard Test Method...

Methods for Evaluating Flammability Characteristics of Shipboard Materials

DTIC Science & Technology

1994-02-28

E 23 • smoke optical properties; and • (toxic) gas production rates. In general, the prediction of these full-scale burning characteristics requires ...Method. The ASTM Room/Corner Test Method can be used to calculate the heat release rate of a material based upon oxygen depletion calorimetry. As can be...Clearly, more validation is required for the theoretical calculations . All are consistent in the use of calorimeter and UFT-type property data, all show

27 CFR 21.6 - Incorporations by reference.

Code of Federal Regulations, 2010 CFR

2010-04-01

..._regulations/ibr_locations.html. (b) Material from Parts 23, 25, and 29 of the 1980 Annual Book of ASTM..._locations.html. (c) Material from the “Official Methods of Analysis of the Association of Official.../federal_register/code_of_federal_regulations/ibr_locations.html. [T.D. ATF-133, 48 FR 24673, June 2, 1983...

40 CFR 72.13 - Incorporation by reference.

Code of Federal Regulations, 2010 CFR

2010-07-01

... and Material (ASTM), 1916 Race Street, Philadelphia, Pennsylvania 19103; and the University Microfilms International 300 North Zeeb Road, Ann Arbor, Michigan 48106. (1) ASTM D388-92, Standard Classification of Coals by Rank for § 72.2 of this chapter. (2) ASTM D396-90a, Standard Specification for Fuel Oils, for § 72...

40 CFR 1065.1010 - Reference materials.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Method for Phosphorus in Gasoline 1065.710 ASTM D3237-06e01, Standard Test Method for Lead in Gasoline By... atomic absorption spectrometry 1065.705 IP-500, Determination of the phosphorus content of residual fuels..., iron, sodium, calcium, zinc and phosphorus in residual fuel oil by ashing, fusion and inductively...

INTERLABORATORY STUDY OF THE COLD VAPOR TECHNIQUE FOR TOTAL MERCURY IN WATER

EPA Science Inventory

The American Society for Testing and Materials (ASTM) and the U.S. Environmental Protection Agency (EPA) conducted a joint study of the cold vapor technique for total mercury in water, before formal acceptance of the method by each organization. The method employs an acid-permang...

40 CFR 98.7 - What standardized methods are incorporated by reference into this part?

Code of Federal Regulations, 2014 CFR

2014-07-01

...-B2959, (800) 262-1373, http://www.astm.org. (1) ASTM C25-06 Standard Test Method for Chemical Analysis...), § 98.174(b), § 98.184(b), § 98.194(c), and § 98.334(b). (2) ASTM C114-09 Standard Test Methods for... Dry Cleaning Solvent), IBR approved for § 98.6. (4) ASTM D240-02 (Reapproved 2007) Standard Test...

77 FR 2456 - Incorporation of Revised ASTM Standards That Provide Flexibility in the Use of Alternatives to...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-18

... (General Bomb Method), IBR approved for appendix A to subpart D. (4) ASTM D287-92, Standard Test Method for... Method for Sulfur in Petroleum Products (General Bomb Method), IBR approved for Sec. 94.108. (4) ASTM...

19 CFR 151.12 - Accreditation of commercial laboratories.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., published by such organizations as the American Society for Testing and Materials (ASTM) and the American... American Society for Testing and Materials (ASTM) E548 (Standard Guide for General Criteria Used for... bachelor's degree in science or have two years related experience in an analytical laboratory. (g) How will...

19 CFR 151.12 - Accreditation of commercial laboratories.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., published by such organizations as the American Society for Testing and Materials (ASTM) and the American... American Society for Testing and Materials (ASTM) E548 (Standard Guide for General Criteria Used for... bachelor's degree in science or have two years related experience in an analytical laboratory. (g) How will...

19 CFR 151.12 - Accreditation of commercial laboratories.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., published by such organizations as the American Society for Testing and Materials (ASTM) and the American... American Society for Testing and Materials (ASTM) E548 (Standard Guide for General Criteria Used for... bachelor's degree in science or have two years related experience in an analytical laboratory. (g) How will...

19 CFR 151.12 - Accreditation of commercial laboratories.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., published by such organizations as the American Society for Testing and Materials (ASTM) and the American... American Society for Testing and Materials (ASTM) E548 (Standard Guide for General Criteria Used for... bachelor's degree in science or have two years related experience in an analytical laboratory. (g) How will...

19 CFR 151.12 - Accreditation of commercial laboratories.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., published by such organizations as the American Society for Testing and Materials (ASTM) and the American... American Society for Testing and Materials (ASTM) E548 (Standard Guide for General Criteria Used for... bachelor's degree in science or have two years related experience in an analytical laboratory. (g) How will...

46 CFR 164.120-5 - Incorporation by reference.

Code of Federal Regulations, 2012 CFR

2012-10-01

...), IBR approved for § 164.120-7 (“ASTM D 543”). (2) ASTM D 570-98 (Reapproved 2005), Standard Test Method for Water Absorption of Plastics, (approved November 1, 2005), IBR approved for § 164.120-7 (“ASTM D 570”). (3) ASTM D 638-08, Standard Test Method for Tensile Properties of Plastics, (approved April 1...

27 CFR 21.107 - Ethyl acetate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... applicable ASTM method, see 1980 Annual Book of ASTM Standards, Part 29, page 70, Standard No. D 302-58 (1975.... (5) Specific gravity at 20 °/20 °C. Not less than 0.899. (6) Distillation range. (For applicable ASTM method, see 1980 Annual Book of ASTM Standards, Part 29, page 433, Standard No. D 3127-77; for...

75 FR 43107 - Full-Size and Non-Full Size Baby Cribs: Withdrawal of Advance Notice of Proposed Rulemaking

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-23

... worked with the voluntary standards group, ASTM International (formerly known as the American Society for Testing and Materials), which added provisions in its standard for full-size baby cribs, ASTM F 1169, to... the same as voluntary standards ASTM F 1169-10, Standard Consumer Safety Specification for Full-Size...

ASTM and VAMAS activities in titanium matrix composites test methods development

NASA Technical Reports Server (NTRS)

Johnson, W. S.; Harmon, D. M.; Bartolotta, P. A.; Russ, S. M.

1994-01-01

Titanium matrix composites (TMC's) are being considered for a number of aerospace applications ranging from high performance engine components to airframe structures in areas that require high stiffness to weight ratios at temperatures up to 400 C. TMC's exhibit unique mechanical behavior due to fiber-matrix interface failures, matrix cracks bridged by fibers, thermo-viscoplastic behavior of the matrix at elevated temperatures, and the development of significant thermal residual stresses in the composite due to fabrication. Standard testing methodology must be developed to reflect the uniqueness of this type of material systems. The purpose of this paper is to review the current activities in ASTM and Versailles Project on Advanced Materials and Standards (VAMAS) that are directed toward the development of standard test methodology for titanium matrix composites.

Test Methods for Vertebrate Pest Control and Management Materials. A Symposium Sponsored by ASTM Committee E-35 on Pesticides, American Society for Testing and Materials, Monterey, California, March 8, 1976.

ERIC Educational Resources Information Center

Jackson, W. B., Ed.; Marsh, R. E., Ed.

The first symposium on "Test Methods for Vertebrate Pest Management" was held in March, 1976. Much of the thrust was toward explaining and defining the "state of the art." Concerns included rodents and rabbits, predators, scavengers, and large game animals, and a variety of bird species. Environments were as restricted as a…

Biocompatibility of metal injection molded versus wrought ASTM F562 (MP35N) and ASTM F1537 (CCM) cobalt alloys.

PubMed

Chen, Hao; Sago, Alan; West, Shari; Farina, Jeff; Eckert, John; Broadley, Mark

2011-01-01

We present a comparative analysis between biocompatibility test results of wrought and Metal Injection Molded (MIM) ASTM F562-02 UNS R30035 (MP35N) and F1537 UNS R31538 (CCM) alloy samples that have undergone the same generic orthopedic implant's mechanical, chemical surface pre-treatment, and a designed pre-testing sample preparation method. Because the biocompatibility properties resulting from this new MIM cobalt alloy process are not well understood, we conducted tests to evaluate cytotoxicity (in vitro), hemolysis (in vitro), toxicity effects (in vivo), tissue irritation level (in vivo), and pyrogenicity count (in vitro) on such samples. We show that our developed MIM MP35N and CCM materials and treatment processes are biocompatible, and that both the MIM and wrought samples, although somewhat different in microstructure and surface, do not show significant differences in biocompatibility.

40 CFR 761.19 - References.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Products (General Bomb Method) § 761.71(b)(2)(vi) ASTM D 240-87 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuel by Bomb Calorimeter § 761.71(b)(2)(vi) ASTM D 482-87 Standard Test Method... in New and Used Petroleum Products (Bomb Method) § 761.71(b)(2)(vi) ASTM D 923-86 Standard Test...

Method for Estimating Evaporative Potential (IM/CLO) from ASTM Standard Single Wind Velocity Measures

DTIC Science & Technology

2016-08-10

IM/CLO) FROM ASTM STANDARD SINGLE WIND VELOCITY MEASURES DISCLAIMER The opinions or assertions contained herein are the private views of the...USARIEM TECHNICAL REPORT T16-14 METHOD FOR ESTIMATING EVAPORATIVE POTENTIAL (IM/CLO) FROM ASTM STANDARD SINGLE WIND VELOCITY...ASTM STANDARD SINGLE WIND VELOCITY MEASURES Adam W. Potter Biophysics and Biomedical Modeling Division U.S. Army Research Institute of Environmental

Comparison of ASTM D613 and ASTM D6890

DTIC Science & Technology

2016-04-01

product , process, or service by trade name, trademark, manufacturer, or otherwise, does not necessarily constitute or imply its endorsement...state or reflect those of the United States Government or the DoA, and shall not be used for advertising or product endorsement purposes...methylnaphthalene proved to be an impractical material for reference values. The ASTM Diesel National Exchange Group ran a study and determined that

40 CFR 721.5185 - Morpholine, 4-(1-oxo-2-propenyl)-.

Code of Federal Regulations, 2010 CFR

2010-07-01

...), (a)(5)(i), (a)(5)(ii), (a)(5)(iii), (a)(5)(xii), (a)(5)(xiii), (a)(5)(xiv), (a)(5)(xv), (a)(6)(v), (b) (concentration set at 0. 1 percent), and (c). The following material has been tested in accordance with the American Society for Testing Materials (ASTM) F739 method and found by EPA to satisfy the consent order's...

Relation between the national handbook of recommended methods for water data acquisition and ASTM standards

USGS Publications Warehouse

Glysson, G. Douglas; Skinner, John V.

1991-01-01

In the late 1950's, intense demands for water and growing concerns about declines in the quality of water generated the need for more water-resources data. About thirty Federal agencies, hundreds of State, county and local agencies, and many private organizations had been collecting water data. However, because of differences in procedures and equipment, many of the data bases were incompatible. In 1964, as a step toward establishing more uniformity, the Bureau of the Budget (now the Office of Management and Budget, OMB) issued 'Circular A-67' which presented guidelines for collecting water data and also served as a catalyst for creating the Office of Water Data Coordination (OWDC) within the U.S. Geological Survey. This paper discusses past, present, and future aspects of the relation between methods in the National Handbook and standards published by ASTM (American Society for Testing and Materials) Committee D-19 on Water's Subcommittee D-19.07 on Sediment, Geomorphology, and Open Channel Flow. The discussion also covers historical aspects of standards - development work jointly conducted by OWDC and ASTM.

Developing a More Rapid Test to Assess Sulfate Resistance of Hydraulic Cements

PubMed Central

Ferraris, Chiara; Stutzman, Paul; Peltz, Max; Winpigler, John

2005-01-01

External sulfate attack of concrete is a major problem that can appear in regions where concrete is exposed to soil or water containing sulfates, leading to softening and cracking of the concrete. Therefore, it is important that materials selection and proportioning of concrete in susceptible regions be carefully considered to resist sulfate attack. American Society for Testing Materials (ASTM) limits the tricalcium aluminate phase in cements when sulfate exposure is of concern. The hydration products of tricalcium aluminate react with the sulfates resulting in expansion and cracking. While ASTM standard tests are available to determine the susceptibility of cements to sulfate attack, these tests require at least 6 months and often up to a year to perform; a delay that hinders development of new cements. This paper presents a new method for testing cement resistance to sulfate attack that is three to five times faster than the current ASTM tests. Development of the procedure was based upon insights on the degradation process by petrographic examination of sulfate-exposed specimens over time. Also key to the development was the use of smaller samples and tighter environmental control. PMID:27308177

Fire Safety Tests for Spherical Resorcinol Formaldehyde Resin: Data Summary Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Dong-Sang; Peterson, Reid A.; Schweiger, Michael J.

2012-07-30

A draft safety evaluation of the scenario for spherical resorcinol-formaldehyde (SRF) resin fire inside the ion exchange column was performed by the Hanford Tank Waste Treatment and Immobilization Plant (WTP) Fire Safety organization. The result of this draft evaluation suggested a potential change of the fire safety classification for the Cesium Ion Exchange Process System (CXP) emergency elution vessels, equipment, and piping, which may be overly bounding based on the fire performance data from the manufacturer of the ion exchange resin selected for use at the WTP. To resolve this question, the fire properties of the SRF resin were measuredmore » by Southwest Research Institute (SwRI), following the American Society for Testing and Materials (ASTM) standard procedures, through a subcontract managed by Pacific Northwest National Laboratory (PNNL). For some tests, the ASTM standard procedures were not entirely appropriate or practical for the SRF resin material, so the procedures were modified and deviations from the ASTM standard procedures were noted. This report summarizes the results of fire safety tests performed and reported by SwRI. The efforts by PNNL were limited to summarizing the test results provided by SwRI into one consolidated data report. All as-received SwRI reports are attached to this report in the Appendix. Where applicable, the precision and bias of each test method, as given by each ASTM standard procedure, are included and compared with the SwRI test results of the SRF resin.« less

40 CFR 80.585 - What is the process for approval of a test method for determining the sulfur content of diesel or...

Code of Federal Regulations, 2010 CFR

2010-07-01

... Society for Testing and Materials (ASTM) or International Standards Organization (ISO), shall be approved... description of the technology and/or instrumentation that makes the method functional. (2) Information... part 51. Anyone may purchase copies of this standard from the American Society for Testing and...

40 CFR 80.585 - What is the process for approval of a test method for determining the sulfur content of diesel or...

Code of Federal Regulations, 2011 CFR

2011-07-01

... Society for Testing and Materials (ASTM) or International Standards Organization (ISO), shall be approved... description of the technology and/or instrumentation that makes the method functional. (2) Information... part 51. Anyone may purchase copies of this standard from the American Society for Testing and...

40 CFR Appendix A to Subpart II of... - VOC Data Sheet 1

Code of Federal Regulations, 2010 CFR

2010-07-01

...: (Dc)s __ g/L [] ASTM D1475-90 *[] Other 3 B. Total Volatiles: (mv)s __ Mass Percent [] ASTM D2369-93....14. 3 Explain the other method used under “Remarks.” [] ASTM D3792-91 *[] ASTM D4017-81, 90, or 96a... (nonvolatiles) 2. __ g/L coating (less water and exempt compounds) G. Thinner Density: Dth __ g/L ASTM...

46 CFR 58.03-1 - Incorporation by reference.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Test Method for Flash and Fire Points by Cleveland Open Cup (“ASTM D 92”), 58.30-10; (8) ASTM D 93-97, Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester (“ASTM D 93”), 58.01-10; and (9...

46 CFR 58.03-1 - Incorporation by reference.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Test Method for Flash and Fire Points by Cleveland Open Cup (“ASTM D 92”), 58.30-10; (8) ASTM D 93-97, Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester (“ASTM D 93”), 58.01-10; and (9...

33 CFR 127.003 - Incorporation by reference.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Testing and Materials (ASTM) 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. ASTM F 1121-87 (1993... NFPA 51B, Fire Prevention in Use of Cutting and Welding Processes, 1994 127.405; 127.1405 NFPA 59A...

Comparison of different measurement methods for transmittance haze

NASA Astrophysics Data System (ADS)

Yu, Hsueh-Ling; Hsaio, Chin-Chai

2009-08-01

Transmittance haze is increasingly important to the LCD and solar cell industry. Most commercial haze measurement instruments are designed according to the method recommended in the documentary standards like ASTM D 1003 (ASTM 2003 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics), JIS K 7361 (JIS 1997 Plastics—Determination of the Total Luminous Transmittance of Transparent Materials—Part 1: Single Beam Instrument) and ISO 14782 (ISO 1997 Plastics—Determination of Haze of Transparent Materials). To improve the measurement accuracy of the current standards, a new apparatus was designed by the Center for Measurement Standards (Yu et al 2006 Meas. Sci. Technol. 17 N29-36). Besides the methods mentioned above, a double-beam method is used in the design of some instruments. There are discrepancies between the various methods. But no matter which method is used, a white standard is always needed. This paper compares the measurement results from different methods, presents the effect of the white standard, and analyses the measurement uncertainty.

Biotribological evaluation of artificial disc arthroplasty devices: influence of loading and kinematic patterns during in vitro wear simulation.

PubMed

Grupp, Thomas M; Yue, James J; Garcia, Rolando; Basson, Janet; Schwiesau, Jens; Fritz, Bernhard; Blömer, Wilhelm

2009-01-01

Wear simulation is an essential pre-clinical method to predict the mid- and long-term clinical wear behavior of newly introduced devices for total disc arthroplasty. The main requirement of a suitable method for spinal wear simulation has to be the ability to distinguish between design concepts and allow for a direct comparison of predicate devices. The objective of our study was to investigate the influence of loading and kinematic patterns based on two different protocols for spinal wear simulation (ISO/FDIS 18192-1 (2006) and ASTM F2423-05). In vitro wear simulation was performed with six activ L lumbar artificial disc devices (Aesculap Tuttlingen, Germany). The applied kinematic pattern of movement was multidirectional for ISO (elliptic track) and unidirectional with a curvilinear shape for ASTM. Testing was done for 10 million cycles in the ISO loading mode and afterwards with the same specimens for 5 million cycles according to the ASTM protocol with a customized six-station servohydraulic spinal wear simulator (EndoLab Thansau, Germany). Gravimetrical and geometrical wear assessment, a slide track analysis correlated to an optical surface characterization, and an estimation of particle size and morphology were performed. The gravimetric wear rate for the first 10 million cycles was ISO(initial) = 2.7 +/- 0.3 mg/million cycles. During the ASTM test period (10-15 million cycles) a gravimetric wear rate of 0.14 +/- 0.06 mg/million cycles was estimated. The wear rates between the ISO and ASTM driven simulations differ substantially (approximately 20-fold) and statistical analysis demonstrates a significant difference (p < 0.001) between the test groups. The main explanation of divergency between ISO and ASTM driven wear simulations is the multidirectional pattern of movement described in the ISO document resulting in a cross-shear stress on the polyethylene material. Due to previous retrieval observations, it seems to be very unlikely that a lumbar artificial disc is loaded with a linear wear path.Testing according to ASTM F2423-05 with pure unidirectional motion does not reflect the kinematics of TDA patients' daily activities. Based on our findings it seems to be more reliable to predict the clinical wear behavior of an artificial disc replacement using the ISO/FDIS 18192-1 method.

Biotribological evaluation of artificial disc arthroplasty devices: influence of loading and kinematic patterns during in vitro wear simulation

PubMed Central

Yue, James J.; Garcia, Rolando; Basson, Janet; Schwiesau, Jens; Fritz, Bernhard; Blömer, Wilhelm

2008-01-01

Wear simulation is an essential pre-clinical method to predict the mid- and long-term clinical wear behavior of newly introduced devices for total disc arthroplasty. The main requirement of a suitable method for spinal wear simulation has to be the ability to distinguish between design concepts and allow for a direct comparison of predicate devices. The objective of our study was to investigate the influence of loading and kinematic patterns based on two different protocols for spinal wear simulation (ISO/FDIS 18192-1 (2006) and ASTM F2423-05). In vitro wear simulation was performed with six activ® L lumbar artificial disc devices (Aesculap Tuttlingen, Germany). The applied kinematic pattern of movement was multidirectional for ISO (elliptic track) and unidirectional with a curvilinear shape for ASTM. Testing was done for 10 million cycles in the ISO loading mode and afterwards with the same specimens for 5 million cycles according to the ASTM protocol with a customized six-station servohydraulic spinal wear simulator (EndoLab Thansau, Germany). Gravimetrical and geometrical wear assessment, a slide track analysis correlated to an optical surface characterization, and an estimation of particle size and morphology were performed. The gravimetric wear rate for the first 10 million cycles was ISOinitial = 2.7 ± 0.3 mg/million cycles. During the ASTM test period (10–15 million cycles) a gravimetric wear rate of 0.14 ± 0.06 mg/million cycles was estimated. The wear rates between the ISO and ASTM driven simulations differ substantially (approximately 20-fold) and statistical analysis demonstrates a significant difference (p < 0.001) between the test groups. The main explanation of divergency between ISO and ASTM driven wear simulations is the multidirectional pattern of movement described in the ISO document resulting in a cross-shear stress on the polyethylene material. Due to previous retrieval observations, it seems to be very unlikely that a lumbar artificial disc is loaded with a linear wear path.Testing according to ASTM F2423-05 with pure unidirectional motion does not reflect the kinematics of TDA patients‘ daily activities. Based on our findings it seems to be more reliable to predict the clinical wear behavior of an artificial disc replacement using the ISO/FDIS 18192-1 method. PMID:19050942

Third Annual Joint Service Pollution Prevention Conference and Exhibition. "Achieving Compliance Through Pollution Prevention"

DTIC Science & Technology

1998-01-01

ASTM D5229, "Standard Test Method for Moisture Absorption Properties and Equilibrium Conditioning of Polymer Matrix Composite Materials." Sandwich...and pollution prevention. Methods and techniques have been established to make building disassembly and salvage cost-competitive with complete...specialized construction methods . • If natural resource conservation is a goal, consider timber framing using sustainably harvested timber, and

Gravimetric measurements of materials outgassing applied to graphite-epoxy laminates

NASA Technical Reports Server (NTRS)

Scialdone, John J.

1990-01-01

The outgassing rates of two graphite-epoxy laminates, American Cyanamide 985B-626 and HST-7B-112, were obtained using a gravimetric method. The rates as a function of time and temperature were derived from the measurements of their mass losses at temperatures varying from 25 to 150 C and for a time span of up to 400 hours in a vacuum. The data from those measurements were reduced to obtain the outgassing activation energies, the mass losses per unit mass or area, and the corresponding outgassing rates. The rates are expressed in closed-form equations and are directly usable for modeling computations. The procedures to obtain these parameters are shown and may be used for the evaluation of other materials. The results of the tests show that the activation energies of the two materials are: 4630 cal/mole for the 985B-626 materials and 4791 cal/mole for the HST-7B-112 sample no. 10 Graphite Epoxy. The outgassing rates of these materials are in the 1OE-5 g sq cm/hr range and they decay according to a power of time of 0.60 at 25 C, indicating that the outgassing process is mainly a diffusion at that temperature. The normalized mass losses versus time obtained from these tests were compared to the discrete results obtained from the ASTM-E595 tests. The comparison provides general indications on the effects of temperature and time in relation to the ASTM test values obtained at 125 C for a 24-hour test duration.

Gravimetric measurements of materials outgassing applied to graphite-epoxy laminates

NASA Technical Reports Server (NTRS)

Scialdone, John J.

1989-01-01

The outgassing rates of two graphite-epoxy laminates, American Cyanamide 985B-626 and HST-7B-112, were obtained using a gravimetric method. The rates as a function of time and temperature were derived from the measurements of their mass losses at temperatures varying from 25 to 150 C and for a time span of up to 400 hours in a vacuum. The data from those measurements were reduced to obtain the outgassing activation energies, the mass losses per unit mass or area, and the corresponding outgassing rates. The rates are expressed in closed-form equations and are directly usable for medling computations. The procedures to obtain these parameters are shown and may be used for the evaluation of other materials. The results of the tests show that the activation energies of the two materials are: 4630 cal/mole for the 985B-626 materials and 4791 cal/mole for the HST-7B-112 sample no. 10 Graphite Exoxy. The outgassing rates of these materials are in the 10E-5 g/sq cm/hr range and they decay according to a power of time of 0.60 at 25 C, indicating that the outgassing process is mainly a diffusion at that temperature. The normalized mass losses versus time obtained from these tests were compared to the discrete results obtained from the ASTM-E595 tests. The comparison provides general indications on the effects of temperature and time in relation to the ASTM test values obtained at 125 C for a 24-hour test duration.

An Experimental Copyright Moratorium: Study of a Proposed Solution to the Copyright Photocopying Problem. Final Report to the American Society for Testing and Materials (ASTM).

ERIC Educational Resources Information Center

Heilprin, Laurence B.

The Committee to Investigate Copyright Problems (CICP), a non-profit organization dedicated to resolving the conflict known as the "copyright photocopying problem" was joined by the American Society for Testing and Materials (ASTM), a large national publisher of technical and scientific standards, in a plan to simulate a long-proposed…

ASTM Committee D-7 : Wood : promoting safety and standardization for 100 years

Treesearch

David W. Green; Robert L. Ethington

2004-01-01

In October 2004, Committee D-7 on Wood of the American Society for Testing and Materials (ASTM) is celebrating 100 years of contributions to the safe and efficient use of wood as a building material. Born during a period of rapid social, economic, and technological change, the Committee faced controversial issues and the challenge of a changing forest resource. This...

Laboratory Characterization of SAM-35 Concrete

DTIC Science & Technology

2006-09-01

procedures given in American Society for Testing and Materials (ASTM) D 2216 (ASTM 2002e). Based on the appropriate values of posttest water content, wet...composition properties of the material. All of the mechanical property tests were conducted quasi -statically with axial strain rates on the order...nondestructive pulse-velocity measurements were performed on each specimen. The TXC tests exhibited a continuous increase in principal stress

Laboratory Characterization of White Masonry Concrete

DTIC Science & Technology

2006-09-01

procedures given in American Society for Testing and Materials (ASTM) D 2216 (ASTM 2002e). Based on the appropriate values of posttest water content...properties of the material. All of the mechanical property tests were conducted quasi -statically with axial strain rates on the order of 10-4 to 10...mechanical property tests, nondestructive pulse-velocity measurements were performed on each specimen. The TXC tests exhibited a continuous increase

PROPOSED ASTM METHOD FOR THE DETERMINATION OF ASBESTOS IN AIR BY TEM AND INFORMATION ON INTERFERING FIBERS

EPA Science Inventory

The draft of the ASTM Test Method for air entitled: "Airborne Asbestos Concentration in Ambient and Indoor Atmospheres as Determined by Transmission Electron Microscopy Direct Transfer (TEM)" (ASTM Z7077Z) is an adaptation of the International Standard, ISO 10312. It is currently...

Heat release from wood wall assemblies using oxygen consumption method

Treesearch

Hao C. Tran; Robert E. White

1990-01-01

The concept of heat release rate is gaining acceptance in the evaluation of fire performance of materials and assemblies. However, this concept has not been incorporated into fire endurance testing such as the ASTM E-119 test method. Heat release rate of assemblies can be useful in determining the time at which the assemblies start to contribute to the controlled fire...

46 CFR 56.01-2 - Incorporation by reference.

Code of Federal Regulations, 2011 CFR

2011-10-01

...) American Society of Mechanical Engineers (ASME) International, Three Park Avenue, New York, NY 10016-5990... (“ASME SA-675”), 56.60-2. (e) ASTM International (formerly American Society for Testing and Materials... 15540 Ships and Marine Technology-Fire Resistance of Hose Assemblies-Test Methods, First Edition (Aug. 1...

77 FR 31742 - Energy Conservation Program for Consumer Products and Certain Commercial and Industrial Equipment...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-30

.... Test Procedure for Commercial Prerinse Spray Valves 4. Design Requirements for Showerheads 5... procedures prescribed or amended under this section shall be reasonably designed to produce test results...] American Society for Testing and Materials [ASTM] Standard F2324, entitled `Standard Test Method for Pre...

Fitting psychometric functions using a fixed-slope parameter: an advanced alternative for estimating odor thresholds with data generated by ASTM E679.

PubMed

Peng, Mei; Jaeger, Sara R; Hautus, Michael J

2014-03-01

Psychometric functions are predominately used for estimating detection thresholds in vision and audition. However, the requirement of large data quantities for fitting psychometric functions (>30 replications) reduces their suitability in olfactory studies because olfactory response data are often limited (<4 replications) due to the susceptibility of human olfactory receptors to fatigue and adaptation. This article introduces a new method for fitting individual-judge psychometric functions to olfactory data obtained using the current standard protocol-American Society for Testing and Materials (ASTM) E679. The slope parameter of the individual-judge psychometric function is fixed to be the same as that of the group function; the same-shaped symmetrical sigmoid function is fitted only using the intercept. This study evaluated the proposed method by comparing it with 2 available methods. Comparison to conventional psychometric functions (fitted slope and intercept) indicated that the assumption of a fixed slope did not compromise precision of the threshold estimates. No systematic difference was obtained between the proposed method and the ASTM method in terms of group threshold estimates or threshold distributions, but there were changes in the rank, by threshold, of judges in the group. Overall, the fixed-slope psychometric function is recommended for obtaining relatively reliable individual threshold estimates when the quantity of data is limited.

Mechanical and Physical Properties of ASTM C33 Sand

DTIC Science & Technology

2008-02-01

ERDC/GSL TR-08-2 7 Grain-size Distribution (1) (ASTM D 422) 1 test run on total sand sample Proctor Density Curves (2) (ASTM D 698 and D... Proctor (Figure 4). Because of the noncohesive nature of the SP material, a series of relative density tests measuring both minimum and maximum... density tests were conducted with moisture added to the sand. A summary of the minimum and maximum densities is given in Table 2. During Proctor

Design of Measurement Apparatus for Electromagnetic Shielding Effectiveness Using Flanged Double Ridged Waveguide

NASA Astrophysics Data System (ADS)

Kwon, Jong Hwa; Choi, Jae Ick; Yook, Jong Gwan

In this paper, we design and manufacture a flanged double ridged waveguide with a tapered section as a sample holder for measuring the electromagnetic shielding effectiveness (SE) of planar material in broadband frequency ranges up to 10GHz. The proposed technique overcomes the limitations of the conventional ASTM D4935 test method at high frequencies. The simulation results for the designed sample holders agree well with the fabricated ones in consideration of the design specification of S11 < -20dB within the frequency range of 1-10GHz. To verify the proposed measurement apparatus, the measured SE data of the commercial shielding materials from 1 to 10GHz were indirectly compared with those obtained from the ASTM D4935 from 30MHz to 1GHz. We observed that the SE data obtained by using both experimental techniques agree with each other.

Crack Growth Testing of an Aluminum Oxynitride (AlON) for International Space Station Kick Panes

NASA Technical Reports Server (NTRS)

Salem, Jonathan A.

2017-01-01

The mechanical properties of an aluminum oxynitride supplied as ground beams and disks were measured using ASTM International (formerly American Society for Testing and Materials) standard test methods. The slow crack growth tests were complicated by a "short" finish that increased strength scatter. Refining of the finish by more material removal in the second stage of grinding or the use of uniaxial grinding as specified in ASTM C1499 might have avoided the issue. The structural design parameters are an elastic modulus of E = 319 GPa, Poisson's ratio of v = 0.26, a fracture toughness of KIvb(A) = 2.18 MPa/m, slow crack growth (SCG) parameter n = 36, and SCG parameter A = 1.96 x 10-11 m/s.(MPa/m)n. For a ground finish, the Weibull parameters are a mean modulus of m = 14.0 and characteristic strength of ?sigma theta = 250.2 MPa. The 2015 vintage material exhibits similar mechanical properties to a 2010 vintage billet. Indentation flaws were not sensitive to the inherent crack growth mechanisms of this material and produced misleading results.

ASTM Committee C28: International Standards for Properties and Performance of Advanced Ceramics, Three Decades of High-quality, Technically-rigorous Normalization

NASA Technical Reports Server (NTRS)

Jenkins, Michael G.; Salem, Jonathan A.

2016-01-01

Physical and mechanical properties and performance of advanced ceramics and glasses are difficult to measure correctly without the proper techniques. For over three decades, ASTM Committee C28 on Advanced Ceramics, has developed high quality, rigorous, full-consensus standards (e.g., test methods, practices, guides, terminology) to measure properties and performance of monolithic and composite ceramics that may be applied to glasses in some cases. These standards testing particulars for many mechanical, physical, thermal, properties and performance of these materials. As a result these standards provide accurate, reliable, repeatable and complete data. Within Committee C28 users, producers, researchers, designers, academicians, etc. have written, continually updated, and validated through round-robin test programs, nearly 50 standards since the Committees founding in 1986. This paper provides a retrospective review of the 30 years of ASTM Committee C28 including a graphical pictogram listing of C28 standards along with examples of the tangible benefits of advanced ceramics standards to demonstrate their practical applications.

76 FR 67673 - Welded ASTM A-312 Stainless Steel Pipe From South Korea and Taiwan: Final Results of Expedited...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-02

... meets the standards and specifications set forth by the American Society for Testing and Materials (ASTM... produced by forming stainless steel flat-rolled products into a tubular configuration and welding along the...

16 CFR 460.7 - Which test version to use.

Code of Federal Regulations, 2010 CFR

2010-01-01

... HOME INSULATION § 460.7 Which test version to use. Use the version of the ASTM test method that was in effect when this regulation was promulgated. If ASTM changes a test method, the new version will automatically replace the old one in these rules 90 days after ASTM first publishes the change. However, the...

ASTM international workshop on standards and measurements for tissue engineering scaffolds.

PubMed

Simon, Carl G; Yaszemski, Michael J; Ratcliffe, Anthony; Tomlins, Paul; Luginbuehl, Reto; Tesk, John A

2015-07-01

The "Workshop on Standards & Measurements for Tissue Engineering Scaffolds" was held on May 21, 2013 in Indianapolis, IN, and was sponsored by the ASTM International (ASTM). The purpose of the workshop was to identify the highest priority items for future standards work for scaffolds used in the development and manufacture of tissue engineered medical products (TEMPs). Eighteen speakers and 78 attendees met to assess current scaffold standards and to prioritize needs for future standards. A key finding was that the ASTM TEMPs subcommittees (F04.41-46) have many active "guide" documents for educational purposes, but few standard "test methods" or "practices." Overwhelmingly, the most clearly identified need was standards for measuring the structure of scaffolds, followed by standards for biological characterization, including in vitro testing, animal models and cell-material interactions. The third most pressing need was to develop standards for assessing the mechanical properties of scaffolds. Additional needs included standards for assessing scaffold degradation, clinical outcomes with scaffolds, effects of sterilization on scaffolds, scaffold composition, and drug release from scaffolds. Discussions highlighted the need for additional scaffold reference materials and the need to use them for measurement traceability. Workshop participants emphasized the need to promote the use of standards in scaffold fabrication, characterization, and commercialization. Finally, participants noted that standards would be more broadly accepted if their impact in the TEMPs community could be quantified. Many scaffold standard needs have been identified and focus is turning to generating these standards to support the use of scaffolds in TEMPs. © 2014 Wiley Periodicals, Inc.

Chemical and physical properties of dry flue gas desulfurization products.

PubMed

Kost, David A; Bigham, Jerry M; Stehouwer, Richard C; Beeghly, Joel H; Fowler, Randy; Traina, Samuel J; Wolfe, William E; Dick, Warren A

2005-01-01

Beneficial and environmentally safe recycling of flue gas desulfurization (FGD) products requires detailed knowledge of their chemical and physical properties. We analyzed 59 dry FGD samples collected from 13 locations representing four major FGD scrubbing technologies. The chemistry of all samples was dominated by Ca, S, Al, Fe, and Si and strong preferential partitioning into the acid insoluble residue (i.e., coal ash residue) was observed for Al, Ba, Be, Cr, Fe, Li, K, Pb, Si, and V. Sulfur, Ca, and Mg occurred primarily in water- or acid-soluble forms associated with the sorbents or scrubber reaction products. Deionized water leachates (American Society for Testing and Materials [ASTM] method) and dilute acetic acid leachates (toxicity characteristic leaching procedure [TCLP] method) had mean pH values of >11.2 and high mean concentrations of S primarily as SO(2-)4 and Ca. Concentrations of Ag, As, Ba, Cd, Cr, Hg, Pb, and Se (except for ASTM Se in two samples) were below drinking water standards in both ASTM and TCLP leachates. Total toxicity equivalents (TEQ) of dioxins, for two FGD products used for mine reclamation, were 0.48 and 0.53 ng kg(-1). This was similar to the background level of the mine spoil (0.57 ng kg(-1)). The FGD materials were mostly uniform in particle size. Specific surface area (m2 g(-1)) was related to particle size and varied from 1.3 for bed ash to 9.5 for spray dryer material. Many of the chemical and physical properties of these FGD samples were associated with the quality of the coal rather than the combustion and SO2 scrubbing processes used.

Evaluation of Storage Effects on Commercial, Biodegradable, Synthetic or Bio-sourced Hydraulic Fluid

DTIC Science & Technology

2007-01-10

Water Content (ASTM D 6304) Coulometric Karl Fischer Titration for water content was conducted in accordance with ASTM D 6304, Standard Test Method ...Point7 (ASTM D 92) • Lubricity (4-Ball Wear)8 (ASTM D 4172) • Total Acid Number (TAN)9 (ASTM D 664) • Water Content by Karl Fischer Coulometric...2001 and the data from FLTT in 2005. However, FLTT procured a new Karl Fischer water titrator in 2003. But FLTT continued to use the same

HACCP: Integrating Science and Management through ASTM Standards

EPA Science Inventory

From a technical perspective, hazard analysis-critical control point (HACCP) evaluation may be considered a risk management tool suited to a wide range of applications. As one outcome of a symposium convened by American Society for Testing and Materials (ASTM) in August, 2005, th...

49 CFR 179.300-7 - Materials.

Code of Federal Regulations, 2014 CFR

2014-10-01

... ASTM A 515/A 515M Gr. 70 70,000 20 ASTM A 516/A 516M Gr. 70 70,000 20 1 Maximum stresses to be used in...) [Reserved] (c) All plates must have their heat number and the name or brand of the manufacturer legibly...

49 CFR 179.300-7 - Materials.

Code of Federal Regulations, 2013 CFR

2013-10-01

... ASTM A 515/A 515M Gr. 70 70,000 20 ASTM A 516/A 516M Gr. 70 70,000 20 1 Maximum stresses to be used in...) [Reserved] (c) All plates must have their heat number and the name or brand of the manufacturer legibly...

Notched bar Izod impact properties of zinc die castings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schrems, K.K.; Dogan, O.N.; Goodwin, F.E.

2007-03-01

Notched bar Izod impact testing of zinc die cast Alloy 3, Alloy 5, ZA-8, and AcuZinc 5 was performed at five temperatures between -40\\mDC and room temperature in accordance with ASTM E23 for impact testing of metallic materials. A direct comparison between ASTM D256 for impact testing of plastics and ASTM E23 was performed using continuously cast zinc specimens of Alloy 5 and ZA-8 at -40\\mDC and room temperature. There are differences in sample sizes, impact velocity, and striker geometry between the two tests. Bulk zinc tested according to ASTM E23 resulted in higher impact energies at -40\\mDC and lowermore » impact energies at room temperature then did the same alloys when tested according to ASTM D256.« less

Experimental Investigation of Mechanical Properties of Welded Corten Steel A588 Grade Plate Using ER70S - 6 Filler Material for Construction Application

NASA Astrophysics Data System (ADS)

Deepak, J. R.; Bupesh Raja, V. K.; Janardhan Guptha, Mittapalli; Durga Prasad, Palaparthi Hari; Sriram, V.

2017-05-01

ASTM A588 Grade A steel plate is a high strength, low alloy structural steel with 0.19 % of carbon content. When exposed to the atmosphere, A588 Grade A is suitable for construction in the bare (paint - free) condition. The main problems are lack of fusion, lack of penetration and corrosion on heat affected zone. In this research work Corten ASTM A588 Grade steel of 3mm thickness is electroplated with copper and then both raw and copper electroplated are welded by GMAW welding process with ER70S-6 as a filler material. The welded ASTM A588 is cut according to ASTM size for further testing of mechanical properties. Considering its welding strength after the process of electroplating, this research clearly states the metal can be utilized for better results in any given field. Here both the tensile and hardness are higher in copper electroplated welded when compare to raw welded.

Results of ASTM round robin testing for mode 1 interlaminar fracture toughness of composite materials

NASA Technical Reports Server (NTRS)

Obrien, T. Kevin; Martin, Roderick H.

1992-01-01

The results are summarized of several interlaboratory 'round robin' test programs for measuring the mode 1 interlaminar fracture toughness of advanced fiber reinforced composite materials. Double Cantilever Beam (DCB) tests were conducted by participants in ASTM committee D30 on High Modulus Fibers and their Composites and by representatives of the European Group on Fracture (EGF) and the Japanese Industrial Standards Group (JIS). DCB tests were performed on three AS4 carbon fiber reinforced composite materials: AS4/3501-6 with a brittle epoxy matrix; AS4/BP907 with a tough epoxy matrix; and AS4/PEEK with a tough thermoplastic matrix. Difficulties encountered in manufacturing panels, as well as conducting the tests are discussed. Critical issues that developed during the course of the testing are highlighted. Results of the round robin testing used to determine the precision of the ASTM DCB test standard are summarized.

Deicer scaling resistance of concrete mixtures containing slag cement. Phase 2 : evaluation of different laboratory scaling test methods.

DOT National Transportation Integrated Search

2012-07-01

With the use of supplementary cementing materials (SCMs) in concrete mixtures, salt scaling tests such as ASTM C672 have been found to be overly aggressive and do correlate well with field scaling performance. The reasons for this are thought to be b...

24 CFR 3280.604 - Materials.

Code of Federal Regulations, 2012 CFR

2012-04-01

.... Welding and Seamless Wrought Steel Pipe—ANSI/ASME B36.10-1979. Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless—ASTM A53-93. Pipe Threads, General Purpose (Inch... Seamless Copper Pipe, Standard Sizes—ASTM B42-93. Standard Specification for General Requirements for...

24 CFR 3280.604 - Materials.

Code of Federal Regulations, 2013 CFR

2013-04-01

.... Welding and Seamless Wrought Steel Pipe—ANSI/ASME B36.10-1979. Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless—ASTM A53-93. Pipe Threads, General Purpose (Inch... Seamless Copper Pipe, Standard Sizes—ASTM B42-93. Standard Specification for General Requirements for...

24 CFR 3280.604 - Materials.

Code of Federal Regulations, 2011 CFR

2011-04-01

.... Welding and Seamless Wrought Steel Pipe—ANSI/ASME B36.10-1979. Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless—ASTM A53-93. Pipe Threads, General Purpose (Inch... Seamless Copper Pipe, Standard Sizes—ASTM B42-93. Standard Specification for General Requirements for...

40 CFR 260.11 - References.

Code of Federal Regulations, 2011 CFR

2011-07-01

...). (7) ASTM E 168-88, “Standard Practices for General Techniques of Infrared Quantitative Analysis,” IBR...-Visible Quantitative Analysis,” IBR approved for § 264.1063. (9) ASTM E 260-85, “Standard Practice for... materials are available for purchase from the Environmental Protection Agency, Research Triangle Park, NC...

46 CFR 175.600 - Incorporation by reference.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Vessels Under 61 Meters (200 feet) in Length, 1983 (“ABS Steel Vessel Rules (Meters)”) 177.300. Rules..., Standard Practice for Operating Salt Spray (Fog) Apparatus (“ASTM B 117”) 175.400. ASTM B 122/B 122M-95... (“ASTM D 93”) 175.400. ASTM D 635-97, Standard test Method for Rate of Burning and or Extent and Time of...

Alternative Fuels Data Center: ASTM Biodiesel Specifications

Science.gov Websites

purchased from ASTM International. Property Test Method Grade No.1-B S15 Grade No.1-B S500 Grade No.2-B S15 ASTM International. Property Test Method Grade B6 to B20 S15 B6 to B20 S500 j B6 to B20 S5000 Acid for the intended use and expected ambient temperatures. Test Methods D 4539 and D 6371 may be useful

Standards and guidelines for biopolymers in tissue-engineered medical products: ASTM alginate and chitosan standard guides. American Society for Testing and Materials.

PubMed

Dornish, M; Kaplan, D; Skaugrud, O

2001-11-01

The American Society for Testing and Materials (ASTM) is making a concerted effort to establish standards and guidelines for the entire field of tissue-engineered medical products (TEMPS). Safety, consistency, and functionality of biomaterials used as matrices, scaffolds, and immobilizing agents in TEMPS are a concern. Therefore, the ASTM has established a number of task groups to produce standards and guidelines for such biomaterials. Alginate is a naturally occurring biomaterial used for immobilizing living cells to form an artificial organ, such as encapsulated pancreatic islets. In order to aid in successful clinical applications and to help expedite regulatory approval, the alginate used must be fully documented. The ASTM alginate guide gives information on selection of testing methodologies and safety criteria. Critical parameters such as monomer content, molecular weight, and viscosity, in addition to more general parameters, such as dry matter content, heavy metal content, bioburden, and endotoxin content are described in the ASTM document. In a like manner, the characterization parameters for chitosan, a bioadhesive polycationic polysaccharide, are described in a separate guide. For chitosan, the degree of deacetylation is of critical importance. Control of protein content and, hence, potential for hypersensitivity, endotoxin content, and total bioburden are important in chitosan preparations for TEMPS. Together these two guides represent part of the effort on behalf of the ASTM and other interested parties to ensure quality and standardization in TEMPS.

Performance Concept in Buildings. Volume 1: Invited Papers. Proceedings of a Symposium Jointly Sponsored by the International Union of Testing and Research Laboratories for Materials and Structures (RILEM), the American Society for Testing and Materials (ASTM), and the International Council for Building Research Studies and Documentation (CIB) (Philadelphia, Pennsylvania, May 2-5, 1972).

ERIC Educational Resources Information Center

Foster, Bruce E., Ed.

Volume 1 contains all the invited papers accepted for the symposium. The subject matter covered in the papers includes physiological, anthropometrical, psychological, sociological, and economic human requirements and methods of evaluation; physical requirements and methods of evaluation in mechanical, acoustical, thermal, dimensional stability,…

Application of a Novel DCPD Adjustment Method for the J-R Curve Characterization: A study based on ORNL and ASTM Interlaboratory Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Xiang; Sokolov, Mikhail A; Nanstad, Randy K

Material fracture toughness in the fully ductile region can be described by a J-integral vs. crack growth resistance curve (J-R curve). As a conventional J-R curve measurement method, the elastic unloading compliance (EUC) method becomes impractical for elevated temperature testing due to relaxation of the material and friction induced back-up shape of the J-R curve. One alternative solution of J-R curve testing applies the Direct Current Potential Drop (DCPD) technique for measuring crack extension. However, besides crack growth, potential drop can also be influenced by plastic deformation, crack tip blunting, etc., and uncertainties exist in the current DCPD methodology especiallymore » in differentiating potential drop due to stable crack growth and due to material deformation. Thus, using DCPD for J-R curve determination remains a challenging task. In this study, a new adjustment procedure for applying DCPD to derive the J-R curve has been developed for conventional fracture toughness specimens, including compact tension, three-point bend, and disk-shaped compact specimens. Data analysis has been performed on Oak Ridge National Laboratory (ORNL) and American Society for Testing and Materials (ASTM) interlaboratory results covering different specimen thicknesses, test temperatures, and materials, to evaluate the applicability of the new DCPD adjustment procedure for J-R curve characterization. After applying the newly-developed procedure, direct comparison between the DCPD method and the normalization method on the same specimens indicated close agreement for the overall J-R curves, as well as the provisional values of fracture toughness near the onset of ductile crack extension, Jq, and of tearing modulus.« less

Filtration Effects Due to Bioassay Cage Design and Screen Type

DTIC Science & Technology

2010-01-01

Optical Nonimaging Light- Scattering Instruments (ASTM, 2003). Droplet sizing data included volume median diam (DV50), and the 10% and 90% diam (DV10 and...optical nonimaging light-scattering instru- ments. In: Annual book of ASTM standards. West Conshohocken, PA: American Society for Testing and Materials

40 CFR 1065.1010 - Reference materials.

Code of Federal Regulations, 2013 CFR

2013-07-01

... for Aviation Turbine Fuels, IBR approved for § 1065.701. (10) ASTM D1837-02a (Reapproved 2007...), IBR approved for § 1065.720. (19) ASTM D2880-03, Standard Specification for Gas Turbine Fuel Oils, IBR... Fuels and Aviation Turbine Fuels By Supercritical Fluid Chromatography, IBR approved for § 1065.703. (26...

40 CFR 1065.1010 - Reference materials.

Code of Federal Regulations, 2012 CFR

2012-07-01

... for Aviation Turbine Fuels, IBR approved for § 1065.701. (10) ASTM D1837-02a (Reapproved 2007...), IBR approved for § 1065.720. (19) ASTM D2880-03, Standard Specification for Gas Turbine Fuel Oils, IBR... Fuels and Aviation Turbine Fuels By Supercritical Fluid Chromatography, IBR approved for § 1065.703. (26...

Applications of Automation Methods for Nonlinear Fracture Test Analysis

NASA Technical Reports Server (NTRS)

Allen, Phillip A.; Wells, Douglas N.

2013-01-01

Using automated and standardized computer tools to calculate the pertinent test result values has several advantages such as: 1. allowing high-fidelity solutions to complex nonlinear phenomena that would be impractical to express in written equation form, 2. eliminating errors associated with the interpretation and programing of analysis procedures from the text of test standards, 3. lessening the need for expertise in the areas of solid mechanics, fracture mechanics, numerical methods, and/or finite element modeling, to achieve sound results, 4. and providing one computer tool and/or one set of solutions for all users for a more "standardized" answer. In summary, this approach allows a non-expert with rudimentary training to get the best practical solution based on the latest understanding with minimum difficulty.Other existing ASTM standards that cover complicated phenomena use standard computer programs: 1. ASTM C1340/C1340M-10- Standard Practice for Estimation of Heat Gain or Loss Through Ceilings Under Attics Containing Radiant Barriers by Use of a Computer Program 2. ASTM F 2815 - Standard Practice for Chemical Permeation through Protective Clothing Materials: Testing Data Analysis by Use of a Computer Program 3. ASTM E2807 - Standard Specification for 3D Imaging Data Exchange, Version 1.0 The verification, validation, and round-robin processes required of a computer tool closely parallel the methods that are used to ensure the solution validity for equations included in test standard. The use of automated analysis tools allows the creation and practical implementation of advanced fracture mechanics test standards that capture the physics of a nonlinear fracture mechanics problem without adding undue burden or expense to the user. The presented approach forms a bridge between the equation-based fracture testing standards of today and the next generation of standards solving complex problems through analysis automation.

Compliance Testing of Grissom Air Force Base Central Heating Plant Coal- Fired Boilers 3, 4, and 5, Grissom Air Force Base, Indiana

DTIC Science & Technology

1992-06-01

coal as classified ac- Department of Environmental Manage- be or, a wet basis and the following conver- cording to ASTM D388-88, "Standard ment...fifteen (15) minutes at the same Sec. 5. (a) Owners or operators of af- erifte p)iute at te me coal as classified according to ASTM fected facilities shall...representative of normal operations or conditions; under other capacities or conditions Testing and Materials ( ASTM ) proce- (B) additional tests to allow

21 CFR 177.1320 - Ethylene-ethyl acrylate copolymers.

Code of Federal Regulations, 2013 CFR

2013-04-01

... scan from 10.5 microns to 12.5 microns. Obtain a baseline absorbance at 11.6 microns and divide by the... specific gravity of not less than 0.920 nor more than 0.935, as determined by ASTM method D1505-68... incorporated by reference. Copies may be obtained from the American Society for Testing Materials, 100 Barr...

21 CFR 177.1320 - Ethylene-ethyl acrylate copolymers.

Code of Federal Regulations, 2012 CFR

2012-04-01

... scan from 10.5 microns to 12.5 microns. Obtain a baseline absorbance at 11.6 microns and divide by the... specific gravity of not less than 0.920 nor more than 0.935, as determined by ASTM method D1505-68... incorporated by reference. Copies may be obtained from the American Society for Testing Materials, 100 Barr...

21 CFR 172.862 - Oleic acid derived from tall oil fatty acids.

Code of Federal Regulations, 2012 CFR

2012-04-01

... titer (solidification point) shall not exceed 13.5 °C and unsaponifiable matter shall not exceed 0.5.... (2) The resin acid content does not exceed 0.01 as determined by ASTM method D1240-82, “Standard Test... the American Society for Testing Materials, 100 Barr Harbor Dr., West Conshohocken, Philadelphia, PA...

Diffusion and solubility coefficients determined by permeation and immersion experiments for organic solvents in HDPE geomembrane.

PubMed

Chao, Keh-Ping; Wang, Ping; Wang, Ya-Ting

2007-04-02

The chemical resistance of eight organic solvents in high density polyethylene (HDPE) geomembrane has been investigated using the ASTM F739 permeation method and the immersion test at different temperatures. The diffusion of the experimental organic solvents in HDPE geomembrane was non-Fickian kinetic, and the solubility coefficients can be consistent with the solubility parameter theory. The diffusion coefficients and solubility coefficients determined by the ASTM F739 method were significantly correlated to the immersion tests (p<0.001). The steady state permeation rates also showed a good agreement between ASTM F739 and immersion experiments (r(2)=0.973, p<0.001). Using a one-dimensional diffusion equation based on Fick's second law, the diffusion and solubility coefficients obtained by immersion test resulted in over estimates of the ASTM F739 permeation results. The modeling results indicated that the diffusion and solubility coefficients should be obtained using ASTM F739 method which closely simulates the practical application of HDPE as barriers in the field.

SRC-I demonstration plant analytical laboratory methods manual. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klusaritz, M.L.; Tewari, K.C.; Tiedge, W.F.

1983-03-01

This manual is a compilation of analytical procedures required for operation of a Solvent-Refined Coal (SRC-I) demonstration or commercial plant. Each method reproduced in full includes a detailed procedure, a list of equipment and reagents, safety precautions, and, where possible, a precision statement. Procedures for the laboratory's environmental and industrial hygiene modules are not included. Required American Society for Testing and Materials (ASTM) methods are cited, and ICRC's suggested modifications to these methods for handling coal-derived products are provided.

Laboratory Characterization of Solid Grade SW Brick

DTIC Science & Technology

2007-08-01

Society for Testing and Materials (ASTM) D 2216 (ASTM 2002e). Based on the appropriate values of posttest water content, wet density, and an assumed...strain path (UX/SP) tests. In addition to the mechanical property tests, nondestructive pulse-velocity measurements were performed on each specimen...Figure 3. Spring-arm lateral deformeter mounted on test specimen

Standard specification for nuclear grade hafnium oxide pellets. ASTM standard

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This specification is under the jurisdiction of ASTM Committee C-26 on Nuclear Fuel Cycle and is the direct responsibility of Subcommittee C26.03 on Neutron Absorber Materials Specifications. Current edition approved May 10, 1997. Published May 1998. Originally published as C 1076-87. Last previous edition C 1076-92.

Permeation of 70% isopropyl alcohol through surgical gloves: comparison of the standard methods ASTM F739 and EN 374.

PubMed

Mäkelä, Erja A; Vainiotalo, Sinikka; Peltonen, Kimmo

2003-06-01

Standard test methods ASTM F739 and EN 374 were compared by assessing the permeation of 70% isopropyl alcohol (2-propanol) through seven brands of surgical gloves. The two standards differ in the flow rates of the collection medium and in the chemical permeation rate at which the breakthrough time (BTT) is detected, the EN detection level being 10 times higher than the permeation rate used by ASTM. In a departure from the EN standard method, a 4 h testing time was used instead of 8 h. All of the tested gloves were from the same manufacturer and were made from either natural rubber (NR) (six brands) or chloroprene rubber (CR) (one brand). Two of the NR glove brands were double layered. For the thin NR gloves (0.22, 0.28 and 0.27 mm) the permeation rates were higher throughout the tests with a flow rate of 474 ml/min (EN) of the collection medium (nitrogen) compared with the permeation rates obtained with a flow rate of 52 ml/min (ASTM). These resulted in BTTs of 4.6, 6.5 and 7.6 min (EN) and 4.8, 6.5 and 9.1 min (ASTM), respectively. No statistical difference could be observed between the BTT values obtained with the two standard methods for any of the thin gloves. Thus, although the ASTM standard has a lower criterion for the detection of permeation, it does not necessarily produce shorter BTTs. For the better barriers the methods yielded more equivalent permeation rate curves and thus the EN BTTs were longer than the ASTM BTTs: the EN results were 21, 80, 122 and >240 min compared with the ASTM results of 12, 32, 38 and 103 min for glove thicknesses of 0.37 (NR), 0.22 + 0.22 (double layered NR), 0.31 + 0.29 (double layered NR) and 0.19 mm (CR), respectively.

ASTM Committee C28: International Standards for Properties and Performance of Advanced Ceramics-Three Decades of High-Quality, Technically-Rigorous Normalization

NASA Technical Reports Server (NTRS)

Jenkins, Michael G.; Salem, Jonathan A.

2016-01-01

Physical and mechanical properties and performance of advanced ceramics and glasses are difficult to measure correctly without the proper techniques. For over three decades, ASTM Committee C28 on Advanced Ceramics, has developed high-quality, technically-rigorous, full-consensus standards (e.g., test methods, practices, guides, terminology) to measure properties and performance of monolithic and composite ceramics that may be applied to glasses in some cases. These standards contain testing particulars for many mechanical, physical, thermal, properties and performance of these materials. As a result these standards are used to generate accurate, reliable, repeatable and complete data. Within Committee C28, users, producers, researchers, designers, academicians, etc. have written, continually updated, and validated through round-robin test programs, 50 standards since the Committee's founding in 1986. This paper provides a detailed retrospective of the 30 years of ASTM Committee C28 including a graphical pictogram listing of C28 standards along with examples of the tangible benefits of standards for advanced ceramics to demonstrate their practical applications.

Collection Efficiencies of Various Airborne Spray Flux Samplers Used in Aerial Application Research

DTIC Science & Technology

2008-01-01

provided by ASTM Standard E1260: Standard Test Method for Determining Liquid Drop Size Characteristics in a Spray Using Optical Nonimaging Light...Size Characteristics in a Spray Using Optical Nonimaging Light-Scattering Instruments,” Annual Book of ASTM Stan- dards, ASTM International, West

Vacuum decay container/closure integrity testing technology. Part 1. ASTM F2338-09 precision and bias studies.

PubMed

Wolf, Heinz; Stauffer, Tony; Chen, Shu-Chen Y; Lee, Yoojin; Forster, Ronald; Ludzinski, Miron; Kamat, Madhav; Godorov, Phillip; Guazzo, Dana Morton

2009-01-01

ASTM F2338-09 Standard Test Method for Nondestructive Detection of Leaks in Packages by Vacuum Decay Method is applicable for leak-testing rigid and semi-rigid non-lidded trays; trays or cups sealed with porous barrier lidding materials; rigid, nonporous packages; and flexible, nonporous packages. Part 1 of this series describes the precision and bias studies performed in 2008 to expand this method's scope to include rigid, nonporous packages completely or partially filled with liquid. Round robin tests using three VeriPac 325/LV vacuum decay leak testers (Packaging Technologies & Inspection, LLC, Tuckahoe, NY) were performed at three test sites. Test packages were 1-mL glass syringes. Positive controls had laser-drilled holes in the barrel ranging from about 5 to 15 microm in nominal diameter. Two different leak tests methods were performed at each site: a "gas leak test" performed at 250 mbar (absolute) and a "liquid leak test" performed at about 1 mbar (absolute). The gas leak test was used to test empty, air-filled syringes. All defects with holes > or = 5.0 microm and all no-defect controls were correctly identified. The only false negative result was attributed to a single syringe with a < 5.0-microm hole. Tests performed using a calibrated air leak supported a 0.10-cm3 x min(-1) (ccm) sensitivity limit (99/99 lower tolerance limit). The liquid leak test was used to test both empty, air-filled syringes and water-filled syringes. Test results were 100% accurate for all empty and water-filled syringes, both without holes and with holes (5, 10, and 15 microm). Tests performed using calibrated air flow leaks of 0, 0.05, and 0.10 ccm were also 100% accurate; data supported a 0.10-ccm sensitivity limit (99/99 lower tolerance limit). Quantitative differential pressure results strongly correlated to hole size using either liquid or gas vacuum decay leak tests. The higher vacuum liquid leak test gave noticeably higher pressure readings when water was present in the defect. Both the ASTM F2338-09 test method and the precision and bias study report are available by contacting ASTM International in West Conshohocken, PA, USA (www.astm.org).

Probabilistic Analysis for Comparing Fatigue Data Based on Johnson-Weibull Parameters

NASA Technical Reports Server (NTRS)

Hendricks, Robert C.; Zaretsky, Erwin V.; Vicek, Brian L.

2007-01-01

Probabilistic failure analysis is essential when analysis of stress-life (S-N) curves is inconclusive in determining the relative ranking of two or more materials. In 1964, L. Johnson published a methodology for establishing the confidence that two populations of data are different. Simplified algebraic equations for confidence numbers were derived based on the original work of L. Johnson. Using the ratios of mean life, the resultant values of confidence numbers deviated less than one percent from those of Johnson. It is possible to rank the fatigue lives of different materials with a reasonable degree of statistical certainty based on combined confidence numbers. These equations were applied to rotating beam fatigue tests that were conducted on three aluminum alloys at three stress levels each. These alloys were AL 2024, AL 6061, and AL 7075. The results were analyzed and compared using ASTM Standard E739-91 and the Johnson-Weibull analysis. The ASTM method did not statistically distinguish between AL 6010 and AL 7075. Based on the Johnson-Weibull analysis confidence numbers greater than 99 percent, AL 2024 was found to have the longest fatigue life, followed by AL 7075, and then AL 6061. The ASTM Standard and the Johnson-Weibull analysis result in the same stress-life exponent p for each of the three aluminum alloys at the median or L(sub 50) lives.

Standards in capstone design courses and the engineering curriculum.

PubMed

Goldberg, Jay

2012-01-01

In 1990, I was the group leader of Research and Development for Surgitek, a urological device manufacturer in Racine, Wisconsin, which was the market leader in ureteral stents. I recognized the need for an industry standard for ureteral stents, felt that taking a leadership role in the development of a new standard would be a good professional development activity, and volunteered to serve as the chair of the American Society for Testing and Materials (ASTM, now known as ASTM International) Task Group on Ureteral Stents. After several years, the standard was approved, and I continue to serve as the chair of the ASTM Subcommittee on Urological Materials and Devices. This experience helped me understand the value of industry standards, expanded my professional network and visibility within the medical device industry, and helped develop my leadership skills.

46 CFR 56.60-1 - Acceptable materials and specifications (replaces 123 and Table 126.1 in ASME B31.1).

Code of Federal Regulations, 2011 CFR

2011-10-01

..., and fittings when it receives certification of their mechanical properties. Without this certification... certifying that the mechanical properties at room temperature specified in ASTM A 520 (incorporated by... manufacturer certifying that the mechanical properties for A192 in ASTM A 520 have been met. Without this...

Development of a Midscale Test for Flame Resistant Protection

DTIC Science & Technology

2016-08-01

Evaluation of Flame Resistant Clothing for Protection against Fire Simulations Using an Instrumented Manikin, which provides both radiant and convective heat...TEST METHODS FIRE RESISTANT MATERIALS TORCHES SIMULATION TEST EQUIPMENT FLAME RESISTANT CLOTHING PERFORMANCE(ENGINEERING... fabric during a fire , and even after the fire has been extinguished. The best known full scale transmitted heat flux test is the "ASTM F1930

Evaluation of SAGE Electrochromic Devices: Cooperative Research and Development Final Report, CRADA Number CRD-15-579

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tenent, Robert C.

2017-12-06

NREL will conduct durability testing of Sage Electrochromics dynamic windows products using American Society for Testing and Materials (ASTM) standard methods and drive parameters as defined by Sage. Window units will be tested and standard analysis performed. Data will be summarized and reported back to Sage at the end of the testing period.

21 CFR 175.270 - Poly(vinyl fluoride) resins.

Code of Federal Regulations, 2014 CFR

2014-04-01

...(vinyl fluoride) basic resins have an intrinsic viscosity of not less than 0.75 deciliter per gram as determined by ASTM method D1243-79, “Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride... (ASTM method D1243-79, “Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers...

Data development for ASTM E24.06.02 round robin program on instability prediction

NASA Technical Reports Server (NTRS)

Mccabe, D. E.

1979-01-01

Basis data for use in an ASTM E24.06.02 task group round robin activity was developed. Compact specimens were made of 2024-T351, 7075-T651 aluminum alloys, and 304 stainless steel. All were 12.7 mm thick and planar dimension variables incorporated were for 1T, 2T and 4T sizes. Representative raw data for each material and specimen size are contained herein. R-curves plotted in terms of delta a physical and delta a effective are plotted for each material.

49 CFR 173.120 - Class 3-Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Closed Cup Tester, (ASTM D 56) (IBR; see § 171.7 of this subchapter); (B) Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus, (ASTM D 3278) (IBR; see § 171.7 of this subchapter... for Flash Point by Pensky-Martens Closed Cup Tester, (ASTM D 93) (IBR; see § 171.7 of this subchapter...

46 CFR 35.25-10 - Requirements for fuel oil-T/ALL.

Code of Federal Regulations, 2010 CFR

2010-10-01

... tankships shall have a flashpoint of not less than 140°F. (Pensky-Martens Closed Cup Method, ASTM D 93... vendor, the name of the oil producer, and the flashpoint (Pensky-Martens Closed Cup Method, ASTM D 93...

46 CFR 35.25-10 - Requirements for fuel oil-T/ALL.

Code of Federal Regulations, 2011 CFR

2011-10-01

... tankships shall have a flashpoint of not less than 140°F. (Pensky-Martens Closed Cup Method, ASTM D 93... vendor, the name of the oil producer, and the flashpoint (Pensky-Martens Closed Cup Method, ASTM D 93...

Ignitability analysis using the cone calorimeter and lift apparatus

Treesearch

Mark A. Dietenberger

1996-01-01

The irradiance plotted as function of time to ignition for wood materials tested in the Cone Calorimeter (ASTM E1354) differs signiticantly from that tested in the Lateral Ignition and Flame spread Test (LIFT) apparatus (ASTM E1321). This difference in piloted ignitabilty is primarily due to the difference in forced convective cooling of the specimen tested in both...

Use of the Digital Surface Roughness Meter in Virginia.

DOT National Transportation Integrated Search

2006-01-01

Pavement surface texture is measured in a variety of ways in Virginia. Two methods commonly used are ASTM E 965, Standard Test Method for Measuring Pavement Macrotexture Depth Using a Volumetric Technique, known as the "sand patch" test, and ASTM E 2...

Roofing research and standards development: Fourth volume. ASTM special technical publication 1349

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wallace, T.J.; Rossiter, W.J. Jr.

1999-07-01

As the roofing industry has stabilized, a broad variety of roof systems have found general acceptance by the building owners, architects, engineers, contractors, and others who select and install roofs. These roof systems include those based on conventional built-up membranes using glass and synthetic reinforcements, synthetic polymeric membranes using elastomers and thermoplastics, polymer-modified membranes, and sprayed polyurethane foam. ASTM Committee D8 on Roofing, Waterproofing, and Bituminous Materials has contributed significantly in many important ways to the roofing community's stabilization including issuing standard specifications to assist consumers in the selection and use of these systems. This is not surprising, as itmore » has always been among the purpose of D8 to provide standards to assist in the selection and use of low-sloped and steep roofing. The Committee's scope includes development of standards associated with application, inspection, maintenance, and analyses. Some of the issues facing the roofing community today--for example, enhanced system durability, better methods of material characterization, environmental impact, recycling of materials and systems, industry conversation to the S.I. system metric--readily fall within D8's scope. The availability of sound standard can contribute to the resolution of many of these issues.« less

The Effect of Curing Temperature on the Fracture Toughness of Fiberglass Epoxy Composites

NASA Astrophysics Data System (ADS)

Ryan, Thomas J.

The curing reaction in a thermoset polymer matrix composite is often accelerated by the addition of heat in an oven or autoclave. The heat added increases the rate of the polymerization reaction and cross-linking in the material. The cure cycle used (temperature, pressure and time) can therefore alter the final material properties. This research focuses on how the curing temperature (250, 275, 300 °F) affects the yield strength and the mode I interlaminar fracture toughness, GI, of a unidirectional S-2 glass epoxy composite. The test method that was used for the tension test was ASTM D3039 and the test method for the mode I interlaminar fracture toughness, the double cantilever beam (DCB) test, was ASTM D5528. The DCB specimens were fabricated with a non-adhesive insert at the midplane of the composite that serves as the initiatior of the delamination. Opening forces were then applied to the specimen, causing the crack propagation. The results show that increasing the cure temperature by 50 °F increased the tensile strength by 10% (86.54 - 94.73 ksi) and decreased the fracture toughness 20% (506.23 - 381.31 J/m 2). Thus, the curing temperature can cause a trade-off between these two properties, which means that the curing cycle will need to be altered based on the intended use and the required material properties.

40 CFR 721.5185 - 2-Propen-1-one, 1-(4-morpholinyl)-.

Code of Federal Regulations, 2013 CFR

2013-07-01

...), (a)(3)(ii), (a)(4), (a)(6)(v), (b) (concentration set at 1.0 percent), and (c). Safety 4/4H EVOH/PE... in accordance with the American Society for Testing Materials (ASTM) F739 method and found by EPA to.... Requirements as specified in § 721.72 (a), (b), (c), (d), (e) (concentration set at 1.0 percent), (f), (g)(1...

40 CFR 721.5185 - 2-Propen-1-one, 1-(4-morpholinyl)-.

Code of Federal Regulations, 2011 CFR

2011-07-01

...), (a)(3)(ii), (a)(4), (a)(6)(v), (b) (concentration set at 1.0 percent), and (c). Safety 4/4H EVOH/PE... in accordance with the American Society for Testing Materials (ASTM) F739 method and found by EPA to.... Requirements as specified in § 721.72 (a), (b), (c), (d), (e) (concentration set at 1.0 percent), (f), (g)(1...

40 CFR 721.5185 - 2-Propen-1-one, 1-(4-morpholinyl)-.

Code of Federal Regulations, 2012 CFR

2012-07-01

...), (a)(3)(ii), (a)(4), (a)(6)(v), (b) (concentration set at 1.0 percent), and (c). Safety 4/4H EVOH/PE... in accordance with the American Society for Testing Materials (ASTM) F739 method and found by EPA to.... Requirements as specified in § 721.72 (a), (b), (c), (d), (e) (concentration set at 1.0 percent), (f), (g)(1...

40 CFR 721.5185 - 2-Propen-1-one, 1-(4-morpholinyl)-.

Code of Federal Regulations, 2014 CFR

2014-07-01

...), (a)(3)(ii), (a)(4), (a)(6)(v), (b) (concentration set at 1.0 percent), and (c). Safety 4/4H EVOH/PE... in accordance with the American Society for Testing Materials (ASTM) F739 method and found by EPA to.... Requirements as specified in § 721.72 (a), (b), (c), (d), (e) (concentration set at 1.0 percent), (f), (g)(1...

Application of self-organizing feature maps to analyze the relationships between ignitable liquids and selected mass spectral ions.

PubMed

Frisch-Daiello, Jessica L; Williams, Mary R; Waddell, Erin E; Sigman, Michael E

2014-03-01

The unsupervised artificial neural networks method of self-organizing feature maps (SOFMs) is applied to spectral data of ignitable liquids to visualize the grouping of similar ignitable liquids with respect to their American Society for Testing and Materials (ASTM) class designations and to determine the ions associated with each group. The spectral data consists of extracted ion spectra (EIS), defined as the time-averaged mass spectrum across the chromatographic profile for select ions, where the selected ions are a subset of ions from Table 2 of the ASTM standard E1618-11. Utilization of the EIS allows for inter-laboratory comparisons without the concern of retention time shifts. The trained SOFM demonstrates clustering of the ignitable liquid samples according to designated ASTM classes. The EIS of select samples designated as miscellaneous or oxygenated as well as ignitable liquid residues from fire debris samples are projected onto the SOFM. The results indicate the similarities and differences between the variables of the newly projected data compared to those of the data used to train the SOFM. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Corrosion Behavior of Sacrificial Coatings on Grade 10.9 Fasteners for Multimetal Armor Applications

DTIC Science & Technology

2013-08-01

hexavalent chromium , immersion, magniplate, trivalent chromium (TCP), bolts nonchromate, hexavalent chrome, grade 10.9 fasteners, bolt-on armor...for Testing and Materials (ASTM) B633 (4) electroplated zinc with hexavalent chromium conversion coating 2. Trivalent Chromium Process (TCP): ASTM...B633 (4) electroplated zinc with trivalent chromium conversion coating 3. AlumiPlate: Process details, entire surface electroplated with aluminum (Al

Accelerated weathering of fire-retardant-treated wood for fire testing

Treesearch

Robert H. White

2009-01-01

Fire-retardant-treated products for exterior applications must be subjected to actual or accelerated weathering prior to fire testing. For fire-retardant-treated wood, the two accelerated weathering methods have been Method A and B of ASTM D 2898. The rain test is Method A of ASTM D 2898. Method B includes exposures to ultraviolet (UV) sunlamps in addition to water...

Promoted Combustion Test Data Re-Examined

NASA Technical Reports Server (NTRS)

Lewis, Michelle; Jeffers, Nathan; Stoltzfus, Joel

2010-01-01

Promoted combustion testing of metallic materials has been performed by NASA since the mid-1980s to determine the burn resistance of materials in oxygen-enriched environments. As the technolo gy has advanced, the method of interpreting, presenting, and applying the promoted combustion data has advanced as well. Recently NASA changed the bum criterion from 15 cm (6 in.) to 3 cm (1.2 in.). This new burn criterion was adopted for ASTM G 124, Standard Test Method for Determining the Combustion Behavior- of Metallic Materials in Oxygen-Enriched Atmospheres. Its effect on the test data and the latest method to display the test data will be discussed. Two specific examples that illustrate how this new criterion affects the burn/no-bum thresholds of metal alloys will also be presented.

Brain activity is related to individual differences in the number of items stored in auditory short-term memory for pitch: evidence from magnetoencephalography.

PubMed

Grimault, Stephan; Nolden, Sophie; Lefebvre, Christine; Vachon, François; Hyde, Krista; Peretz, Isabelle; Zatorre, Robert; Robitaille, Nicolas; Jolicoeur, Pierre

2014-07-01

We used magnetoencephalography (MEG) to examine brain activity related to the maintenance of non-verbal pitch information in auditory short-term memory (ASTM). We focused on brain activity that increased with the number of items effectively held in memory by the participants during the retention interval of an auditory memory task. We used very simple acoustic materials (i.e., pure tones that varied in pitch) that minimized activation from non-ASTM related systems. MEG revealed neural activity in frontal, temporal, and parietal cortices that increased with a greater number of items effectively held in memory by the participants during the maintenance of pitch representations in ASTM. The present results reinforce the functional role of frontal and temporal cortices in the retention of pitch information in ASTM. This is the first MEG study to provide both fine spatial localization and temporal resolution on the neural mechanisms of non-verbal ASTM for pitch in relation to individual differences in the capacity of ASTM. This research contributes to a comprehensive understanding of the mechanisms mediating the representation and maintenance of basic non-verbal auditory features in the human brain. Copyright © 2014 Elsevier Inc. All rights reserved.

40 CFR 80.580 - What are the sampling and testing methods for sulfur?

Code of Federal Regulations, 2010 CFR

2010-07-01

...,000 ppm sulfur standard of § 80.510(k), sulfur content may be determined using ASTM D2622... the 500 ppm sulfur standard of § 80.510(a)(1), sulfur content may be determined using ASTM D2622... to the 1,000 ppm sulfur standard of § 80.510(k), sulfur content may be determined using ASTM D4294...

40 CFR Table 4 to Subpart Zzzz of... - Requirements for Performance Tests

Code of Federal Regulations, 2010 CFR

2010-07-01

... and outlet of the control device; and (1) Portable CO and O2 analyzer. (a) Using ASTM D6522-00 (2005... control device (1) Portable CO and O2 analyzer. (a) Using ASTM D6522-00 (2005) a,b (incorporated by..., appendix A, or ASTM Method D6522-00 (2005) (a) Measurements to determine O2 concentration must be made at...

Assessment of wrought ASTM F1058 cobalt alloy properties for permanent surgical implants.

PubMed

Clerc, C O; Jedwab, M R; Mayer, D W; Thompson, P J; Stinson, J S

1997-01-01

The behavior of the ASTM F1058 wrought cobalt-chromium-nickel-molybdenum-iron alloy (commonly referred to as Elgiloy or Phynox) is evaluated in terms of mechanical properties, magnetic resonance imaging, corrosion resistance, and biocompatibility. The data found in the literature, the experimental corrosion and biocompatibility results presented in this article, and its long track record as an implant material demonstrate that the cobalt superalloy is an appropriate material for permanent surgical implants that require high yield strength and fatigue resistance combined with high elastic modulus, and that it can be safely imaged with magnetic resonance.

Is the apical soft tissue margin a better predictor of biochemical recurrence than the surgical specimen?

PubMed

Godoy, Guilherme; Tareen, Basir U; Lepor, Herbert

2011-01-01

To identify predictors of apical surgical margin (ASM) and apical soft tissue margin (ASTM), determine if the ASTM is a better predictor of biochemical recurrence (BR) than the ASM, and ascertain the impact of apical biopsies on BR rates. One thousand three hundred eight consecutive men underwent open radical retropubic prostatectomy (RP) between October 2000 and December 2006. Circumferential biopsies of the ASTM were obtained intraoperatively and submitted for frozen section analysis. Logistic regression models were utilized to identify the factors associated with the presence of positive ASMs and ASTMs. The estimated 5-year risk of BR was calculated by the Kaplan-Meier method. Overall, 43 (3.3%) and 86 (6.6%) of cases exhibited positive ASM and ASTM, respectively. ASM was significantly associated with higher mean serum prostate-specific antigen levels, presence of perineural invasion, and greater volume of tumor in the biopsy specimen. None of these factors were observed to be associated with the presence of cancer in the ASTMs. In the multivariate analysis, only the presence of perineural invasion was a significant independent predictor of ASMs. The estimated 5-year BR rates in the positive ASMs only, ASTMs only, and both positive ASMs and ASTMs groups were 48.6%, 4.7%, and 38.8%, respectively. A positive ASM was associated with a significantly greater risk of BR compared with a positive ASTM. The very low estimated risk of BR at 5 years in cases with ASTM suggests that performing the ASTM biopsies may increase the cure rates achieved with RP. Copyright © 2011 Elsevier Inc. All rights reserved.

Comparing the Methodologies in ASTM G198: Is There an Easy Way Out?

Treesearch

Samuel L. Zelinka

2013-01-01

ASTM(1) G198, Standard test method for determining the relative corrosion performance of driven fasteners in contact with treated wood, was accepted by consensus and published in 2011. The method has two different exposure conditions for determining fastener corrosion performance in treated wood. The first method places the wood and embedded...

Mechanical characterization of commercial biodegradable plastic films

NASA Astrophysics Data System (ADS)

Vanstrom, Joseph R.

Polylactic acid (PLA) is a biodegradable plastic that is relatively new compared to other plastics in use throughout industry. The material is produced by the polymerization of lactic acid which is produced by the fermentation of starches derived from renewable feedstocks such as corn. Polylactic acid can be manufactured to fit a wide variety of applications. This study details the mechanical and morphological properties of selected commercially available PLA film products. Testing was conducted at Iowa State University and in conjunction with the United States Department of Agriculture (USDA) BioPreferred ProgramRTM. Results acquired by Iowa State were compared to a similar study performed by the Cortec Corporation in 2006. The PLA films tested at Iowa State were acquired in 2009 and 2010. In addition to these two studies at ISU, the films that were acquired in 2009 were aged for a year in a controlled environment and then re-tested to determine effects of time (ageing) on the mechanical properties. All films displayed anisotropic properties which were confirmed by inspection of the films with polarized light. The mechanical testing of the films followed American Society for Testing and Materials (ASTM) standards. Mechanical characteristics included: tensile strength (ASTM D882), elongation of material at failure (ASTM D882), impact resistance (ASTM D1922), and tear resistance (ASTM D4272). The observed values amongst all the films ranged as followed: tensile strength 33.65--8.54 MPa; elongation at failure 1,665.1%--47.2%; tear resistance 3.61--0.46 N; and puncture resistance 2.22--0.28 J. There were significant differences between the observed data for a number of films and the reported data published by the Cortec Corp. In addition, there were significant differences between the newly acquired material from 2009 and 2010, as well as the newly acquired materials in 2009 and the aged 2009 materials, suggesting that ageing and manufacturing date had an effect on the mechanical properties. The morphological properties were tested using Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA). The material properties examined were: glass transition temperature (Tg), degree of crystallinity (Wc), and material composition in terms of inorganic content. Results from DSC testing revealed that the glass transition temperatures ranged from 43.2--52.2 °C, the degree of crystallintiy ranged from 4.1--13.8%, and material composition of the films ranged from 89.9--100% organic materials. The morphological examination of the polymers also indicated that the mechanical properties of the films may have been altered by the manufacturing and processing of the film material or by the addition of filler or plasticizers.

Ocean Engineering Studies. Volume 1. Acrylic Submersibles

DTIC Science & Technology

1990-04-01

2.3 ASTM-DIO03-61 Heat distortion temperature +3.60F/minute at 264 psi 200OF: ASTM-0648-56 +3.60F/minute at 66 psi 220OF ASTM-0648-56 Thermal...of Revolution with Axisymmetric Pressures, Temperatures, and Distributed Loads", WAPD -TM-398, December 1963. 4. Stachiw, J. D., Mack, K. L., "The...at 264 psi 200°F +3.6°F/min at 66 psi 220°F Thermal expansion/°F at 20°F 35 x 10-6 Fed. Stan. 406 Method 2031 Water absorpt,.on; 1/8 inch ASTM-D570

Novel studies of non-aqueous volatiles in lint Cotton moisture tests by complementary thermal methods

USDA-ARS?s Scientific Manuscript database

Moisture affects economical and rheological properties of cotton, making its accurate determination important. A significant difference in moisture contents between the current and most cited standard oven drying ASTM method (ASTM D 2495, SOD) and volumetric Karl Fischer Titration (KFT) has been est...

Methods to Use Surface Infiltration Tests in Permeable Pavement Systems to Determine Maintenance Frequency

EPA Science Inventory

Currently, there is limited guidance on selecting test sites to measure surface infiltration rates in permeable pavement systems to determine maintenance frequency. The ASTM method (ASTM C1701) for measuring infiltration rate of in-place pervious concrete suggest to either (1) p...

Proficiency Testing for Evaluating Aerospace Materials Test Anomalies

NASA Technical Reports Server (NTRS)

Hirsch, D.; Motto, S.; Peyton, S.; Beeson, H.

2006-01-01

ASTM G 86 and ASTM G 74 are commonly used to evaluate materials susceptibility to ignition in liquid and gaseous oxygen systems. However, the methods have been known for their lack of repeatability. The inherent problems identified with the test logic would either not allow precise identification or the magnitude of problems related to running the tests, such as lack of consistency of systems performance, lack of adherence to procedures, etc. Excessive variability leads to increasing instances of accepting the null hypothesis erroneously, and so to the false logical deduction that problems are nonexistent when they really do exist. This paper attempts to develop and recommend an approach that could lead to increased accuracy in problem diagnostics by using the 50% reactivity point, which has been shown to be more repeatable. The initial tests conducted indicate that PTFE and Viton A (for pneumatic impact) and Buna S (for mechanical impact) would be good choices for additional testing and consideration for inter-laboratory evaluations. The approach presented could also be used to evaluate variable effects with increased confidence and tolerance optimization.

Feasibility of Underwater Friction Stir Welding of Hardenable Alloy Steel

DTIC Science & Technology

2010-12-01

Base Material CNC – Computer Numerical Controlled EDM – Electrical Discharge Machining FSP – Friction Stir Processing FSW – Friction Stir Welding...Hydrogen content was determined through vacuum hot extraction according to ASTM E 146-83. All other components were analyzed by direct current plasma ...emission spectroscopy according to ASTM E 1097-07. C. MICROSTRUCTURE ANALYSIS 1. Specimen Preparation A Charmilles Andrew EF630 CNC Wire EDM

Laboratory Characterization of Type N Mortar

DTIC Science & Technology

2009-03-01

and test results are documented in Chapter 2. Comparative plots and anal- yses of the experimental results are presented in Chapter 3. A summary is...determinations are provided in Table 1. Measurements of posttest water content1 were conducted in accordance with procedures given in American Society for...Testing and Materials (ASTM) D 2216 (ASTM 2005d). Based on the appropriate values of posttest water content, wet density, and an assumed grain density

Investigation to Identify Performance Criteria and Test Methods for Evaluating Single-Ply Roofing Systems.

DTIC Science & Technology

1987-03-01

Reinforced Black EPDM Rubber Sheets for Use in Roofing Applications ( Rubber Manufacturers Association [RMAJ, 1984). Minimum Requirements for Fabric-Reinforced...Black Polychloroprene Rubber Sheets for Use in Roofing Applications (RMA, 1984). Minimum Requirements for Non-Reinforced Black EPDM Rubber Sheets for...and materials. The Rubber Manufacturers Amoeiation (RMA) (USA) RMA is funding a study in conjunction with ASTM to evaluate three different EPDM

The breaking load method - Results and statistical modification from the ASTM interlaboratory test program

NASA Technical Reports Server (NTRS)

Colvin, E. L.; Emptage, M. R.

1992-01-01

The breaking load test provides quantitative stress corrosion cracking data by determining the residual strength of tension specimens that have been exposed to corrosive environments. Eight laboratories have participated in a cooperative test program under the auspices of ASTM Committee G-1 to evaluate the new test method. All eight laboratories were able to distinguish between three tempers of aluminum alloy 7075. The statistical analysis procedures that were used in the test program do not work well in all situations. An alternative procedure using Box-Cox transformations shows a great deal of promise. An ASTM standard method has been drafted which incorporates the Box-Cox procedure.

40 CFR 63.7142 - What are the requirements for claiming area source status?

Code of Federal Regulations, 2013 CFR

2013-07-01

... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

40 CFR 63.7142 - What are the requirements for claiming area source status?

Code of Federal Regulations, 2011 CFR

2011-07-01

... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

40 CFR 63.7142 - What are the requirements for claiming area source status?

Code of Federal Regulations, 2012 CFR

2012-07-01

... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

40 CFR 63.7142 - What are the requirements for claiming area source status?

Code of Federal Regulations, 2010 CFR

2010-07-01

... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

40 CFR 63.7142 - What are the requirements for claiming area source status?

Code of Federal Regulations, 2014 CFR

2014-07-01

... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

Biomechanical stability according to different configurations of screws and rods.

PubMed

Ha, Kee-Yong; Hwang, Sung-Chul; Whang, Tae-Hyuk

2013-05-01

Comparison of biomechanical strength according to 2 different configurations of screws and rods. To compare the biomechanical strength of different configurations of screws and rods composed of the same material and of the same size. Many complications related to instrumentation have been reported. The incidence of metallic failure would differ according to the materials and configurations of the assembly of the screws and rods used. However, to our knowledge, the biomechanical effects of implant assembly rods and screws with different configurations and different contours have not been reported. Biomechanical testing was conducted to compare top tightening (TT) screw-rod configuration with side tightening (ST) screw-rod configuration. All tests were conducted using a hydraulic all-purpose testing machine. All data were acquired at a rate of 10 Hz. Both screw systems used spinal rods of 6 mm diameter and were made of TiAl4V ELI material. Among 5 types of tests, 3 were conducted on the basis of American Society for Testing and Materials (ASTM) F 1798 to 97 and F1717-10. The other 2 tests were conducted for comparing the characteristics between TT and ST pedicle screws according to modified methods from ASTM F 1717-10 and ASTM F 1798-97. All results including axial gripping capacity and yield forces were obtained using the same methods on the basis of the mentioned ASTM standards. In the axial gripping capacity test, the mean axial gripping capacity of the TT screw-rod configuration was 3332 ± 118 N and that of ST was 2222 ± 147 N in straight rods (P = 0.019). In 15-degree contoured rods, TT was 2988 ± 199 N and ST was 2116 ± 423 N (P = 0.014). In 30-degree contoured rods, TT was 2227 ± 408 N and ST was 1814 ± 285 N (P = 0.009). In the pulling-out test, the pulling-out force of ST was 8695 ± 1616 N and that of TT was 6106 ± 195 N (P = 0.014). In the rod-pushing test, the failure force of ST was 4131 ± 205 N and that of TT was 5639 ± 105 N. In the compressive fatigue test, the maximum load was 145 N in ST and 119 N in TT. In the cycle fatigue test, the fatigue strength of ST was higher than that of TT. In the rod-pushing test, the failure force of ST was 4131 ± 205 N and that of TT was 5639 ± 105 N (P=0.046). Two different configurations of rod-screw systems found statistically significant differences with axial gripping, pulling out, and fatigue failures. ST constructs improved fixation stability over TT constructs. It was concluded that ST configuration may reduce complications related to implantation.

Corrosion and Fatigue Behavior of High-Strength Steel Treated with a Zn-Alloy Thermo-diffusion Coating

NASA Astrophysics Data System (ADS)

Mulligan, C. P.; Vigilante, G. N.; Cannon, J. J.

2017-11-01

High and low cycle fatigue tests were conducted on high-strength steel using four-point bending. The materials tested were ASTM A723 steel in the as-machined condition, grit-blasted condition, MIL-DTL-16232 heavy manganese phosphate-coated condition, and ASTM A1059 Zn-alloy thermo-diffusion coated (Zn-TDC). The ASTM A723 steel base material exhibits a yield strength of 1000 MPa. The effects of the surface treatments versus uncoated steel were examined. The fatigue life of the Zn-TDC specimens was generally reduced on as-coated specimens versus uncoated or phosphate-coated specimens. Several mechanisms are examined including the role of compressive residual stress relief with the Zn-TDC process as well as fatigue crack initiation from the hardened Zn-Fe alloy surface layer produced in the gas-metal reaction. Additionally, the effects of corrosion pitting on the fatigue life of coated specimens are explored as the Zn-TDC specimens exhibit significantly improved corrosion resistance over phosphate-coated and oiled specimens.

40 CFR 98.324 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Procedures and Inspection Tracking System Handbook Number: PH-08-V-1, January 1, 2008 (incorporated by... paragraphs (d)(1) through (d)(2) of this section. (1) ASTM D1945-03, Standard Test Method for Analysis of... Reformed Gas by Gas Chromatography; ASTM D4891-89 (Reapproved 2006), Standard Test Method for Heating Value...

40 CFR 98.324 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Procedures and Inspection Tracking System Handbook Number: PH-08-V-1, January 1, 2008 (incorporated by... paragraphs (d)(1) through (d)(2) of this section. (1) ASTM D1945-03, Standard Test Method for Analysis of... Reformed Gas by Gas Chromatography; ASTM D4891-89 (Reapproved 2006), Standard Test Method for Heating Value...

40 CFR 98.324 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Procedures and Inspection Tracking System Handbook Number: PH-08-V-1, January 1, 2008 (incorporated by... ASTM D1945-03, Standard Test Method for Analysis of Natural Gas by Gas Chromatography; ASTM D1946-90... (Reapproved 2006), Standard Test Method for Heating Value of Gases in Natural Gas Range by Stoichiometric...

A novel method to determine air leakage in heat pump clothes dryers

DOE PAGES

Bansal, Pradeep; Mohabir, Amar; Miller, William

2016-01-06

A heat pump clothes dryer offers the potential to save a significant amount of energy as compared with conventional vented electric dryers. Although heat pump clothes dryers (HPCD) offer higher energy efficiency; it has been observed that they are prone to air leakages, which inhibits the HPCD's gain in efficiency. This study serves to develop a novel method of quantifying leakage, and to determine specific leakage locations in the dryer drum and air circulation system. The basis of this method is the American Society of Testing and Materials (ASTM) standard E779 10, which is used to determine air leakage areamore » in a household ventilation system through fan pressurization. This ASTM method is adapted to the dryer system, and the leakage area is determined by an analysis of the leakage volumetric flow - pressure relationship. Easily accessible leakage points were quantified: the front and back crease (in the dryer drum), the leakage in the dryer duct, the air filter, and the remaining leakage in the drum. The procedure allows investigators to determine major components contributing to leakage in HPCDs, thus improving component design features that result in more efficient HPCD systems.« less

A novel method to determine air leakage in heat pump clothes dryers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bansal, Pradeep; Mohabir, Amar; Miller, William

A heat pump clothes dryer offers the potential to save a significant amount of energy as compared with conventional vented electric dryers. Although heat pump clothes dryers (HPCD) offer higher energy efficiency; it has been observed that they are prone to air leakages, which inhibits the HPCD's gain in efficiency. This study serves to develop a novel method of quantifying leakage, and to determine specific leakage locations in the dryer drum and air circulation system. The basis of this method is the American Society of Testing and Materials (ASTM) standard E779 10, which is used to determine air leakage areamore » in a household ventilation system through fan pressurization. This ASTM method is adapted to the dryer system, and the leakage area is determined by an analysis of the leakage volumetric flow - pressure relationship. Easily accessible leakage points were quantified: the front and back crease (in the dryer drum), the leakage in the dryer duct, the air filter, and the remaining leakage in the drum. The procedure allows investigators to determine major components contributing to leakage in HPCDs, thus improving component design features that result in more efficient HPCD systems.« less

Validation and Verification (V and V) Testing on Midscale Flame Resistant (FR) Test Method

DTIC Science & Technology

2016-12-16

Method for Evaluation of Flame Resistant Clothing for Protection against Fire Simulations Using an Instrumented Manikin. Validation and...complement (not replace) the capabilities of the ASTM F1930 Standard Test Method for Evaluation of Flame Resistant Clothing for Protection against Fire ...Engineering Center (NSRDEC) to complement the ASTM F1930 Standard Test Method for Evaluation of Flame Resistant Clothing for Protection against Fire

Application of Response Surface Methodology for Modeling of Postweld Heat Treatment Process in a Pressure Vessel Steel ASTM A516 Grade 70.

PubMed

Peasura, Prachya

2015-01-01

This research studied the application of the response surface methodology (RSM) and central composite design (CCD) experiment in mathematical model and optimizes postweld heat treatment (PWHT). The material of study is a pressure vessel steel ASTM A516 grade 70 that is used for gas metal arc welding. PWHT parameters examined in this study included PWHT temperatures and time. The resulting materials were examined using CCD experiment and the RSM to determine the resulting material tensile strength test, observed with optical microscopy and scanning electron microscopy. The experimental results show that using a full quadratic model with the proposed mathematical model is YTS = -285.521 + 15.706X1 + 2.514X2 - 0.004X1(2) - 0.001X2(2) - 0.029X1X2. Tensile strength parameters of PWHT were optimized PWHT time of 5.00 hr and PWHT temperature of 645.75°C. The results show that the PWHT time is the dominant mechanism used to modify the tensile strength compared to the PWHT temperatures. This phenomenon could be explained by the fact that pearlite can contribute to higher tensile strength. Pearlite has an intensity, which results in increased material tensile strength. The research described here can be used as material data on PWHT parameters for an ASTM A516 grade 70 weld.

[Influence of mechanical effect due to MRI-magnet on tattoo seal and eye makeup].

PubMed

Morishita, Yuta; Miyati, Tosiaki; Ueda, Jousei; Shimizu, Mitsuru; Hamaguchi, Takashi; Fujiwara, Yasuhiro; Hayashi, Hiroyuki

2008-05-20

The purpose of our study was to assess the mechanical effect on tattoo seals and eye makeup caused by a spatial magnetic gradient in the magnetic resonance imaging (MRI) system. Seven kinds of tattoo seals and three kinds of eye makeup, i.e., mascara, eye shadow, and eyeliner were used. On a 3.0-Tesla MRI, we determined these deflection angles according to a method established by the American Society for Testing and Materials (ASTM) at the position that produced the greatest magnetically induced deflection. Eighty-five percent of the tattoo seals showed deflection angles greater than 45 degrees of the ASTM guidelines, and the mascara and eye shadow showed over 40 degrees. This was because these contained ferromagnetic pigments such as an iron oxide, but those translational forces were very small owing to slight mass. However, it is desirable that these should be removed before MRI examination to prevent secondary problems.

Army Oil Analysis Program for Vehicle Testing

DTIC Science & Technology

1996-08-16

4 TOP 2-2-690 16 August 1996 (l) Water determination: Karl Fischer method (TM 38-301-2 or ASTM-D1744 3 ): Set up the Karl Fischer titrator in...higher temperature if required. aMagnification. bReflected. CTransmitted. 5. DATA REQUIRED. a. Water: Karl Fischer percent water-- (% H2 0). b...Liquid Petroleum Products by Karl Fischer Reagent, 1984. 4. DL 18, Karl Fischer Titrator Operating Instructions. 5. ASTM-D445, Annual Book of ASTM

The electrical conductivities of candidate beam-waveguide antenna shroud materials

NASA Technical Reports Server (NTRS)

Otoshi, T. Y.; Franco, M. M.

1994-01-01

The shroud on the beam-waveguide (BWG) antenna at DSS 13 is made from highly magnetic American Society for Testing and Materials (ASTM) A36 steel. Measurements at 8.42 GHz showed that this material (with paint) has a very poor electrical conductivity that is 600 times worse than aluminum. In cases where the BWG mirrors might be slightly misaligned, unintentional illumination and poor electrical conductivity of the shroud walls can cause system noise temperature to be increased significantly. This potential increase of noise temperature contribution can be reduced through the use of better conductivity materials for the shroud walls. An alternative is to attempt to improve the conductivity of the currently used ASTM A36 steel by means of some type of plating, surface treatment, or high-conductivity paints. This article presents the results of a study made to find improved materials for future shrouds and mirror supports.

Tradespace Assessment: Thermal Strain Modeling Comparison Of Multiple Clothing Configurations Based On Different Environmental Conditions

DTIC Science & Technology

2017-02-01

risks, by modeling thermal strain. Twenty clothing ensembles were tested for thermal and evaporative resistances according to American Society of...e.g., football, hockey, etc.) or during military, law enforcement, or first responder operations (e.g., body armor, flame resistant clothing, etc...Each clothing configuration was tested to American Society of Testing and Materials (ASTM) standards for “dry” thermal resistance (Rct) (ASTM F1291

Evaluation of the WavTrac Expeditionary Mobility Matting System

DTIC Science & Technology

2017-04-01

pavement applications. Designation D6951. West Conshohocken, PA: ASTM International. www.astm.org. Rushing, T. W., and J. F. Rowland. 2012. Comparison of...respective owners. The findings of this report are not to be construed as an official Department of the Army position unless so designated by other...The technical monitor was Jeb S. Tingle. The work was performed by the Airfields and Pavements Branch (APB) of the Engineering Systems and Materials

Evaluation of Cement, Lime, and Asphalt Amended Municipal Solid Waste Incinerator Residues

DTIC Science & Technology

1989-09-01

the lime column over time ( Atlas & Bartha , 1987). Certainly, a more extensive evaluation of the lime amended residue’s microbial activity is required...4.02 ASTM D 1559 (1988) Annual Book of ASTM Standards: Road & Paving Materials; Traveled Surface Characteristics, Sec 4, Vol 4.03 Atlas , R. & R. Bartha ...1987) Microbial Ecology : Fundamentals & Applications, Benjamin-Cummings, Menlo, CA Barrow N., J. Bowden, A. Posner, & J. Quirk (1981) Describing the

Comparison of attrition test methods: ASTM standard fluidized bed vs jet cup

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, R.; Goodwin, J.G. Jr.; Jothimurugesan, K.

2000-05-01

Attrition resistance is one of the key design parameters for catalysts used in fluidized-bed and slurry phase types of reactors. The ASTM fluidized-bed test has been one of the most commonly used attrition resistance evaluation methods; however, it requires the use of 50 g samples--a large amount for catalyst development studies. Recently a test using the jet cup requiring only 5 g samples has been proposed. In the present study, two series of spray-dried iron catalysts were evaluated using both the ASTM fluidized-bed test and a test based on the jet cup to determine this comparability. It is shown thatmore » the two tests give comparable results. This paper, by reporting a comparison of the jet-cup test with the ASTM standard, provides a basis for utilizing the more efficient jet cup with confidence in catalyst attrition studies.« less

Standard test method for grindability of coal by the Hardgrove-machine method. ASTM standard

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1998-05-01

This test method is under the jurisdiction of ASTM Committee D-5 on Coal and Coke and is the direct responsibility of Subcommittee D05.07 on Physical Characteristics of Coal. The current edition was approved on November 10, 1997, and published May 1998. It was originally published as D 409-51. The last previous edition was D 409-93a.

Comparing the Methodologies in ASTM G198 Using Combined Hygrothermal-Corrosion Modeling

Treesearch

Samuel L. Zelinka

2013-01-01

ASTM G198, “Standard test method for determining the relative corrosion performance of driven fasteners in contact with treated wood,” was accepted by consensus and published in 2011. The method has two different exposure conditions for determining fastener corrosion performance in treated wood. The first method places the wood and embedded fasteners in a...

FUELS IN SOIL TEST KIT: FIELD USE OF DIESEL DOG SOIL TEST KITS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Unknown

2001-05-31

Western Research Institute (WRI) is commercializing Diesel Dog Portable Soil Test Kits for performing analysis of fuel-contaminated soils in the field. The technology consists of a method developed by WRI (U.S. Patents 5,561,065 and 5,976,883) and hardware developed by WRI that allows the method to be performed in the field (patent pending). The method is very simple and does not require the use of highly toxic reagents. The aromatic components in a soil extract are measured by absorption at 254 nm with a field-portable photometer. WRI added significant value to the technology by taking the method through the American Societymore » for Testing and Materials (ASTM) approval and validation processes. The method is designated ASTM Method D-5831-96, Standard Test Method for Screening Fuels in Soils. This ASTM designation allows the method to be used for federal compliance activities. In FY 99, twenty-five preproduction kits were successfully constructed in cooperation with CF Electronics, Inc., of Laramie, Wyoming. The kit components work well and the kits are fully operational. In the calendar year 2000, kits were provided to the following entities who agreed to participate as FY 99 and FY 00 JSR (Jointly Sponsored Research) cosponsors and use the kits as opportunities arose for field site work: Wyoming Department of Environmental Quality (DEQ) (3 units), F.E. Warren Air Force Base, Gradient Corporation, The Johnson Company (2 units), IT Corporation (2 units), TRC Environmental Corporation, Stone Environmental, ENSR, Action Environmental, Laco Associates, Barenco, Brown and Caldwell, Dames and Moore Lebron LLP, Phillips Petroleum, GeoSyntek, and the State of New Mexico. By early 2001, ten kits had been returned to WRI following the six-month evaluation period. On return, the components of all ten kits were fully functional. The kits were upgraded with circuit modifications, new polyethylene foam inserts, and updated instruction manuals.« less

40 CFR 98.324 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Tracking System Handbook Number: PH-08-V-1, January 1, 2008 (incorporated by reference, see § 98.7). You... paragraphs (d)(1) through (d)(2) of this section. (1) ASTM D1945-03, Standard Test Method for Analysis of... Reformed Gas by Gas Chromatography; ASTM D4891-89 (Reapproved 2006), Standard Test Method for Heating Value...

High Temperature, Long Service Life Fuel Cell Bladder Materials

DTIC Science & Technology

2004-03-01

50 Table 19. Inner Liner Rubber , D471 Results – Fluid Aging in JP8+100 @ 225°F............................. 52 Table 20. Inner Liner Rubber ...Tensile Properties – Fluid Aging in JP8+100 @ 225°F ..................... 52 Table 21. Inner Liner Rubber , Tear Properties – Fluid Aging in JP8+100...samples in accordance with ASTM D 471: Test Method for Rubber Property - Effects of Liquids. Fluid aging experiments were performed in friction

Overview (this manuscript is an overview of an ASTM ...

EPA Pesticide Factsheets

The Symposium on Developing Consensus Standards for Measuring Chemical Emissions from Spray Polyurethane Foam (SPF) Insulation was held on April 30th and May 1, 2015. Sponsored by ASTM Committee D22 on Air Quality, the symposium was held in Anaheim, CA, in conjunction with the standards development meetings of the Committee. ASTM D22.05 is developing tools to answer fundamental questions: what is emitted from SPF, how long do the emissions persist, how does ventilation impact concentrations and potential exposures? How can we model these processes to address the multiplicity of products, applications, and environmental conditions that may impact exposure to emissions over the life cycle of the material? These are complex and interrelated questions that have challenged the indoor environments research community for many years. Objectives of Symposium: Standardized methods are needed to assess the potential impacts of SPF insulation products on indoor air quality, establish re-entry times for trade workers or re-occupancy times for building occupants after product installation and to evaluate post-occupancy ventilation. The objective of the symposium was to provide a forum for the exchange of ideas from SPF manufacturers, regulatory agencies, indoor air quality professionals, testing labs, air quality consultants, instrument vendors and other stakeholders. Following the presentations on the current status of measuring emissions from SPF insulation, participants di

Paperless or vanishing society

NASA Astrophysics Data System (ADS)

Turner Luke, Joy

2002-06-01

In the 1940s color photography became available and within a few years, extremely popular. As people switched from black and white photographs made with the old metallic silver process to the new color films, pictures taken to record their lives and families began a slow disappearing act. The various color processes, coupled with the substrates they were printed on, affected their longevity, but many color photographs taken from the late 1950s through the 1970s, and even into the 1980s, faded not only when exposed to the light, but also when stored in the dark. Henry Wilhelm's excellent book 'The Permanence and Care of Color Photographs' documents this history in detail. Today we are making another transition in the storage of pictures and information. There are questions about the longevity of different types of digital storage, and also of the images printed by various types of inkjet printers, or by laser printers using colored toners. Very expensive and very beautiful works of art produced on Iris printers are appearing in art exhibitions. Some of these are referred to as Giclee prints and are offered on excellent papers. Artists are told the prints will last a lifetime; and if by change they don't it is only necessary to make another print. Henry Wilhelm has begun to test and rate these images for lightfastness; however, his test method was developed for examining longevity in colored photographs. It is of interest to find out how these prints will hold up in the tests required for fine art materials. Thus far companies producing digital inks and printers have not invested the time and money necessary to develop an American Society for Testing and Materials (ASTM) standard method for evaluating the lightfastness of digital prints. However, it is possible to use ASTM D 5383, Standard Practice for Visual Determination of the Lightfastness of Art Materials by Art Technologists, to pinpoint colors that will fade in a short time, even though the test is not as severe as ASTM D 4303, which is used to rate the lightfastness of artists's paint.

Cadmium (Tank) Electroplating Alternative

DTIC Science & Technology

2011-08-01

ASTM F519 HE: 75% NFS 200 hrs HRE : 45% NFS 150 hrs Threshold limit greater than /equal to LHE Cd (AMS 2417G) ASETS Defense Focused Workshop (2011...Test Specimens  Reporting Sustained/Threshold load (%NFS), Time to failure. HRE Testing Cd Zn-Ni IVD Al LHE Cd Re-Embrittlement Test Fluids:  DI...Hydrogen Embrittlement/ HRE ASTM F519 A5, Type 1.a.1 Brush Plating ASETS Defense Focused Workshop (2011) Luzmarie G. Santiago Materials Engineer Naval Air

Evaluation of Candidate Materials for Fines Filter Media in the C2 Canister

DTIC Science & Technology

1992-05-01

Philadelphia PA 19103. (5) Owens - Corning Technical Center, "Breaking Strength", Test Report 48708, October 1, 1990. (6) ASTM F778-88, "Gas Flow...strength per ASTM D1682-64. Appendix A 39 OWENS - CORNING TESTING SERVICES TECHNICAL CENTER, 2790 Columbus Rd. OWENS - CORNING FIBERGLAS CORPORATION Granville... Owens - Corning Testing Services makes no warranty, express or implied, whether of merchantability or fitness for any particular purpose, with respect to

Characterization of the fretting corrosion behavior, surface and debris from head-taper interface of two different modular hip prostheses.

PubMed

Dos Santos, Claudio T; Barbosa, Cassio; Monteiro, Maurício J; Abud, Ibrahim C; Caminha, Ieda M V; Roesler, Carlos R M

2016-09-01

Modular hip prostheses are flexible to match anatomical variations and to optimize mechanical and tribological properties of each part by using different materials. However, micromotions associated with the modular components can lead to fretting corrosion and, consequently, to release of debris which can cause adverse local tissue reactions in human body. In the present study, the surface damage and residues released during in vitro fretting corrosion tests were characterized by stereomicroscope, SEM and EDS. Two models of modular hip prosthesis were studied: Model SS/Ti Cementless whose stem was made of ASTM F136 Ti-6Al-4V alloy and whose metallic head was made of ASTM F138 austenitic stainless steel, and Model SS/SS Cemented with both components made of ASTM F138 stainless steel. The fretting corrosion tests were evaluated according to the criteria of ASTM F1875 standard. Micromotions during the test caused mechanical wear and material loss in the head-taper interface, resulting in fretting-corrosion. Model SS/SS showed higher grade of corrosion. Different morphologies of debris predominated in each model studied. Small and agglomerated particles were observed in the Model SS/Ti and irregular particles in the Model SS/SS. After 10 million cycles, the Model SS/Ti was more resistant to fretting corrosion than the Model SS/SS. Copyright © 2016 Elsevier Ltd. All rights reserved.

Determination of calibration constants for the hole-drilling residual stress measurement technique applied to orthotropic composites. I - Theoretical considerations

NASA Technical Reports Server (NTRS)

Prasad, C. B.; Prabhakaran, R.; Tompkins, S.

1987-01-01

The hole-drilling technique for the measurement of residual stresses using electrical resistance strain gages has been widely used for isotropic materials and has been adopted by the ASTM as a standard method. For thin isotropic plates, with a hole drilled through the thickness, the idealized hole-drilling calibration constants are obtained by making use of the well-known Kirsch's solution. In this paper, an analogous attempt is made to theoretically determine the three idealized hole-drilling calibration constants for thin orthotropic materials by employing Savin's (1961) complex stress function approach.

Best Technical Approach for the Petroleum Quality Analysis (PQA) System

DTIC Science & Technology

1994-08-01

two test methods for determination of water content in a fuel. The Karl Fischer titration method (ASTM D 1744) measures for total water, both...difficult to automate. ASTM D 664, "Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration," is simple to automate...release. distribution unlimnied 13. ABSTRACT (Maximum 2C3 words) Recent U.S. militar-y operations have identified a need for improved methods of fuel and

Gas chromatographic sulphur speciation in heavy crude oil using a modified standard D5623 method and microfluidic Deans switching.

PubMed

Heshka, Nicole E; Choy, Joanne M; Chen, Jinwen

2017-12-29

A modification to American Society for Testing and Materials (ASTM) method D5623 is proposed to enable successful and repeatable analysis of heavy crude oil samples. A two-dimensional gas chromatography configuration was implemented, with separation of sulphur compounds occurring on two columns. A Deans switch is used to enable heart-cutting of volatile sulphur compounds onto a DB-Sulfur stationary phase, and separation occurs concurrently with the backflushing of the primary column. The use of a sulphur-selective detector increases selectivity, and 22 volatile sulphur species are quantified in less than 15min, which is almost half the time of the original ASTM method. Samples ranging from light distillation cuts to whole crudes (boiling from 100°C to >750°C) were analyzed with minimal sample preparation. The calculated limit of detection was 0.7mg/kg, repeatability was 3% relative standard deviation (RSD), and a linear range of 1-250mg/kg was obtained, with an R 2 value of 0.994 or better, depending on the compound. Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.

Standard Test Methods for Textile Composites

NASA Technical Reports Server (NTRS)

Masters, John E.; Portanova, Marc A.

1996-01-01

Standard testing methods for composite laminates reinforced with continuous networks of braided, woven, or stitched fibers have been evaluated. The microstructure of these textile' composite materials differs significantly from that of tape laminates. Consequently, specimen dimensions and loading methods developed for tape type composites may not be applicable to textile composites. To this end, a series of evaluations were made comparing testing practices currently used in the composite industry. Information was gathered from a variety of sources and analyzed to establish a series of recommended test methods for textile composites. The current practices established for laminated composite materials by ASTM and the MIL-HDBK-17 Committee were considered. This document provides recommended test methods for determining both in-plane and out-of-plane properties. Specifically, test methods are suggested for: unnotched tension and compression; open and filled hole tension; open hole compression; bolt bearing; and interlaminar tension. A detailed description of the material architectures evaluated is also provided, as is a recommended instrumentation practice.

Application of Response Surface Methodology for Modeling of Postweld Heat Treatment Process in a Pressure Vessel Steel ASTM A516 Grade 70

PubMed Central

Peasura, Prachya

2015-01-01

This research studied the application of the response surface methodology (RSM) and central composite design (CCD) experiment in mathematical model and optimizes postweld heat treatment (PWHT). The material of study is a pressure vessel steel ASTM A516 grade 70 that is used for gas metal arc welding. PWHT parameters examined in this study included PWHT temperatures and time. The resulting materials were examined using CCD experiment and the RSM to determine the resulting material tensile strength test, observed with optical microscopy and scanning electron microscopy. The experimental results show that using a full quadratic model with the proposed mathematical model is Y TS = −285.521 + 15.706X 1 + 2.514X 2 − 0.004X 1 2 − 0.001X 2 2 − 0.029X 1 X 2. Tensile strength parameters of PWHT were optimized PWHT time of 5.00 hr and PWHT temperature of 645.75°C. The results show that the PWHT time is the dominant mechanism used to modify the tensile strength compared to the PWHT temperatures. This phenomenon could be explained by the fact that pearlite can contribute to higher tensile strength. Pearlite has an intensity, which results in increased material tensile strength. The research described here can be used as material data on PWHT parameters for an ASTM A516 grade 70 weld. PMID:26550602

Current activities in standardization of high-temperature, low-cycle-fatigue testing techniques in the United States

NASA Technical Reports Server (NTRS)

Verrilli, Michael J.; Ellis, J. Rodney; Swindeman, Robert W.

1990-01-01

The American Society for Testing and Materials (ASTM) standard E606-80 is the most often used recommended testing practice for low-cycle-fatigue (LCF) testing in the United States. The standard was first adopted in 1977 for LCF testing at room temperature and was modified in 1980 to include high-temperature testing practices. Current activity within ASTM is aimed at extending the E606-80 recommended practices to LCF under thermomechanical conditions, LCF in high-pressure hydrogen, and LCF in metal-matrix composite materials. Interlaboratory testing programs conducted to generate a technical base for modifying E606-80 for the aforementioned LCF test types are discussed.

Repair, Evaluation, Maintenance, and Rehabilitation Research Program: Factors Related to the Performance of Concrete Repair Materials.

DTIC Science & Technology

1988-03-01

in reference HRS 78.) The ASTM C 883 effective shrinkage standard test method involves constructing a laminate consisting of an epoxy-resin system...Evaluation of a Hiah-Strenrth Polyester Snythetic Concrete, U.S. Army Construction Engineering Research Laboratory, CERL Technical Report M-2, Champaign...Colorado, August 1, 1983. Can 67 F. Canovas, (Effects of ) Temperature Ch anges on Epoxy Pavements, Informes de la construccion (Madrid), 19, No. 189, pp

ASTM standards for fire debris analysis: a review.

PubMed

Stauffer, Eric; Lentini, John J

2003-03-12

The American Society for Testing and Materials (ASTM) recently updated its standards E 1387 and E 1618 for the analysis of fire debris. The changes in the classification of ignitable liquids are presented in this review. Furthermore, a new standard on extraction of fire debris with solid phase microextraction (SPME) was released. Advantages and drawbacks of this technique are presented and discussed. Also, the standard on cleanup by acid stripping has not been reapproved. Fire debris analysts that use the standards should be aware of these changes.

ASTM lights the way for tissue engineered medical products standards: jump start for combination medical products that restore biological function of human tissues.

PubMed

Picciolo, G L; Stocum, D L

2001-01-01

Everybody hopes for better health and restoration of impaired bodily function, and now that hope is illuminated by the promise of powerful biological tools that make human cells grow and replace human tissue. ASTM Committee F04 on Medical and Surgical Materials and Devices is taking the lead by defining some of those tools as standards that can be used for the development, production, testing, and regulatory approval of medical products.

40 CFR 94.5 - Reference materials.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., Washington, DC 20460 or at the National Archives and Records Administration (NARA). For information on the.../code_of_federal_regulations/ibr_locations.html. (a) ASTM material. Table 1 of § 94.5 lists material... internal combustion engines—Exhaust emission measurement—Part 1: Test-bed measurement of gaseous and...

Laboratory comparison of several tests for evaluating the transport properties of concrete.

DOT National Transportation Integrated Search

2006-01-01

The transport properties of concrete are a primary element in determining the durability of concrete. In this study, several new test methods that directly measure aspects of fluid and ionic transport in concrete were examined. ASTM C 1543 and ASTM C...

Outgassing Data for Selecting Spacecraft Materials

NASA Technical Reports Server (NTRS)

Campbell, William A., Jr.; Marriott, Richard S.; Park, John J.

1984-01-01

Outgassing data, derived from tests at 396 K (125 C) for 24 hours in vacuum as per ASTM E 595-77, have been compiled for numerous materials for spacecraft use. The data presented are the total mass loss (TML) and the collected volatile condensable materials (CVCM). The various materials are compiled by likely usage and alphabetically.

Measuring Thermal Conductivity at LH2 Temperatures

NASA Technical Reports Server (NTRS)

Selvidge, Shawn; Watwood, Michael C.

2004-01-01

For many years, the National Institute of Standards and Technology (NIST) produced reference materials for materials testing. One such reference material was intended for use with a guarded hot plate apparatus designed to meet the requirements of ASTM C177-97, "Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus." This apparatus can be used to test materials in various gaseous environments from atmospheric pressure to a vacuum. It allows the thermal transmission properties of insulating materials to be measured from just above ambient temperature down to temperatures below liquid hydrogen. However, NIST did not generate data below 77 K temperature for the reference material in question. This paper describes a test method used at NASA's Marshall Space Flight Center (MSFC) to optimize thermal conductivity measurements during the development of thermal protection systems. The test method extends the usability range of this reference material by generating data at temperatures lower than 77 K. Information provided by this test is discussed, as are the capabilities of the MSFC Hydrogen Test Facility, where advanced methods for materials testing are routinely developed and optimized in support of aerospace applications.

Leaching characteristics of solid wastes from thermal power plants of western Turkey and comparison of toxicity methodologies.

PubMed

Baba, Alper; Kaya, Abidin

2004-11-01

Use of lignite in power generation has led to increasing environmental problems associated not only with gaseous emissions, but also with the disposal of ash residues. In particular, use of low quality coals with high ash content results in huge quantities of both fly and bottom ashes to be disposed of. A main problem related to coal ash disposal is the heavy metal content of the residue. In this regard, experimental results of numerous studies indicate that toxic trace metals may leach when fly and bottom ashes are in contact with water. In this study, fly and bottom ash samples obtained from thermal power plants, namely Yenikoy, Kemerkoy and Yatagan, located at the southwestern coast of Turkey, were subjected to toxicity tests such as the extraction (EP) and toxicity characteristic leaching (TCLP) procedures of the US Environmental Protection Agency (USEPA) and the so-called 'Method A' extraction procedure of the American Society of Testing and Material (ASTM). The geochemical composition of ash samples showed variations depending on the coal burned in the plants. Furthermore, the EP, TCLP and ASTM toxicity tests showed variations such that the ash samples were classified as 'toxic waste' based on EP and TCLP results whereas they were classified as 'non-toxic' based on ASTM results, indicating test results are pH dependent. When the extraction results were compared with the chemical composition of water samples obtained in the vicinity of the thermal power plants, it was found that the results obtained using the ASTM procedure cannot be used to predict subsurface contamination whereas the EP and TCLP procedures can be used.

Examination of the Measurement of Absorption Using the Reverberant Room Method for Highly Absorptive Acoustic Foam

NASA Technical Reports Server (NTRS)

Hughes, William O.; McNelis, Anne M.; Chris Nottoli; Eric Wolfram

2015-01-01

The absorption coefficient for material specimens are needed to quantify the expected acoustic performance of that material in its actual usage and environment. The ASTM C423-09a standard, "Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberant Room Method" is often used to measure the absorption coefficient of material test specimens. This method has its basics in the Sabine formula. Although widely used, the interpretation of these measurements are a topic of interest. For example, in certain cases the measured Sabine absorption coefficients are greater than 1.0 for highly absorptive materials. This is often attributed to the diffraction edge effect phenomenon. An investigative test program to measure the absorption properties of highly absorbent melamine foam has been performed at the Riverbank Acoustical Laboratories. This paper will present and discuss the test results relating to the effect of the test materials' surface area, thickness and edge sealing conditions. A follow-on paper is envisioned that will present and discuss the results relating to the spacing between multiple piece specimens, and the mounting condition of the test specimen.

Spray Drift Reduction Evaluations of Spray Nozzles Using a Standardized Testing Protocol

DTIC Science & Technology

2010-07-01

Drop Size Characteristics in a Spray Using Optical Nonimaging Light-Scattering Instruments,” Annual Book of ASTM Standards, Vol. 14-02, ASTM...Test Method for Determining Liquid Drop Size Characteristics in a Spray Using Optical Non- imaging Light-Scattering Instruments 22. AGDISP Model

7 CFR 1755.860 - RUS specification for filled buried wires.

Code of Federal Regulations, 2012 CFR

2012-01-01

... sufficient heat barrier to prevent visible evidence of conductor insulation deformation or adhesion between... Insulations and Jackets for Telecommunications Wire and Cable; ASTM D 4566-90, Standard Test Methods for Electrical Performance Properties of Insulations and Jackets for Telecommunications Wire and Cable; ASTM D...

7 CFR 1755.860 - RUS specification for filled buried wires.

Code of Federal Regulations, 2014 CFR

2014-01-01

... sufficient heat barrier to prevent visible evidence of conductor insulation deformation or adhesion between... Insulations and Jackets for Telecommunications Wire and Cable; ASTM D 4566-90, Standard Test Methods for Electrical Performance Properties of Insulations and Jackets for Telecommunications Wire and Cable; ASTM D...

7 CFR 1755.860 - RUS specification for filled buried wires.

Code of Federal Regulations, 2013 CFR

2013-01-01

... sufficient heat barrier to prevent visible evidence of conductor insulation deformation or adhesion between... Insulations and Jackets for Telecommunications Wire and Cable; ASTM D 4566-90, Standard Test Methods for Electrical Performance Properties of Insulations and Jackets for Telecommunications Wire and Cable; ASTM D...

Evaluation of Surface Infiltration Testing Procedures in Permeable Pavement Systems

EPA Science Inventory

The ASTM method (ASTM C1701) for measuring infiltration rate of in-place pervious concrete provides limited guidance on how to select testing locations, so research is needed to evaluate how testing sites should be selected and how results should be interpreted to assess surface ...

27 CFR 21.114 - Kerosene.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Kerosene. 21.114 Section 21.114 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Kerosene. (a) Distillation range. (For applicable ASTM method, see 1980 Annual Book of ASTM Standards, Part...

27 CFR 21.114 - Kerosene.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2014-04-01 2014-04-01 false Kerosene. 21.114 Section 21.114 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Kerosene. (a) Distillation range. (For applicable ASTM method, see 1980 Annual Book of ASTM Standards, Part...

27 CFR 21.114 - Kerosene.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2011-04-01 2011-04-01 false Kerosene. 21.114 Section 21.114 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Kerosene. (a) Distillation range. (For applicable ASTM method, see 1980 Annual Book of ASTM Standards, Part...

27 CFR 21.114 - Kerosene.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2012-04-01 2012-04-01 false Kerosene. 21.114 Section 21.114 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Kerosene. (a) Distillation range. (For applicable ASTM method, see 1980 Annual Book of ASTM Standards, Part...

27 CFR 21.114 - Kerosene.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2013-04-01 2013-04-01 false Kerosene. 21.114 Section 21.114 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Kerosene. (a) Distillation range. (For applicable ASTM method, see 1980 Annual Book of ASTM Standards, Part...

78 FR 14702 - Hazardous Materials: Miscellaneous Petitions for Rulemaking (RRR)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-07

... Standard Specification for Polyethylene Plastics Molding and Extrusion Materials to provide a range of acceptable resin tolerances in the plastic drum and IBC material; Allow smokeless powder classed as a... incorporate by reference ASTM Standard 04976-06 without stating that plastic drums and IBCs made from...

Comparative analysis of international standards for the fatigue testing of posterior spinal fixation systems.

PubMed

Villa, Tomaso; La Barbera, Luigi; Galbusera, Fabio

2014-04-01

Preclinical evaluation of the long-term reliability of devices for lumbar fixation is a mandatory activity before they are put into market. The experimental setups are described in two different standards edited by the International Organization for Standardization (ISO) and the American Society for Testing Materials (ASTM), but the evaluation of the suitability of such tests to simulate the actual loading with in vivo situations has never been performed. To calculate through finite element (FE) simulations the stress in the rods of the fixator when subjected to ASTM and ISO standards. To compare the calculated stresses arising in the same fixator once it has been virtually mounted in a physiological environment and loaded with physiological forces and moments. FE simulations and validation experimental tests. FE models of the ISO and ASTM setups were created to conduct simulations of the tests prescribed by standards and calculate stresses in the rods. Validation of the simulations were performed through experimental tests; the same fixator was virtually mounted in an L2-L4 FE model of the lumbar spine and stresses in the rods were calculated when the spine was subjected to physiological forces and moments. The comparison between FE simulations and experimental tests showed good agreement between results obtained using the two methodologies, thus confirming the suitability of the FE method to evaluate stresses in the device in different loading situations. The usage of a physiological load with ASTM standard is impossible due to the extreme severity of the ASTM configuration; in this circumstance, the presence of an anterior support is suggested. Also, ISO prescriptions, although the choice of the setup correctly simulates the mechanical contribution of the discs, seem to overstress the device as compared with a physiological loading condition. Some daily activities, other than walking, can induce a further state of stress in the device that should be taken into account in setting up new experimental procedures. ISO standard loading prescriptions seems to be more severe than the expected physiological ones. The ASTM standard should be completed by including some anterior supporting device and declaring the value of the load to be imposed. Moreover, a further enhancement of standards would be simulating other movements representative of daily activities different from walking. Copyright © 2014 Elsevier Inc. All rights reserved.

Probabilistic Analysis for Comparing Fatigue Data Based on Johnson-Weibull Parameters

NASA Technical Reports Server (NTRS)

Vlcek, Brian L.; Hendricks, Robert C.; Zaretsky, Erwin V.

2013-01-01

Leonard Johnson published a methodology for establishing the confidence that two populations of data are different. Johnson's methodology is dependent on limited combinations of test parameters (Weibull slope, mean life ratio, and degrees of freedom) and a set of complex mathematical equations. In this report, a simplified algebraic equation for confidence numbers is derived based on the original work of Johnson. The confidence numbers calculated with this equation are compared to those obtained graphically by Johnson. Using the ratios of mean life, the resultant values of confidence numbers at the 99 percent level deviate less than 1 percent from those of Johnson. At a 90 percent confidence level, the calculated values differ between +2 and 4 percent. The simplified equation is used to rank the experimental lives of three aluminum alloys (AL 2024, AL 6061, and AL 7075), each tested at three stress levels in rotating beam fatigue, analyzed using the Johnson- Weibull method, and compared to the ASTM Standard (E739 91) method of comparison. The ASTM Standard did not statistically distinguish between AL 6061 and AL 7075. However, it is possible to rank the fatigue lives of different materials with a reasonable degree of statistical certainty based on combined confidence numbers using the Johnson- Weibull analysis. AL 2024 was found to have the longest fatigue life, followed by AL 7075, and then AL 6061. The ASTM Standard and the Johnson-Weibull analysis result in the same stress-life exponent p for each of the three aluminum alloys at the median, or L(sub 50), lives

Soils Project Risk-Based Corrective Action Evaluation Process with ROTC 1 and ROTC 2, Revision 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matthews, Patrick; Sloop, Christina

2012-04-01

This document formally defines and clarifies the NDEP-approved process the NNSA/NSO Soils Activity uses to fulfill the requirements of the FFACO and state regulations. This process is used to establish FALs in accordance with the risk-based corrective action (RBCA) process stipulated in Chapter 445 of the Nevada Administrative Code (NAC) as described in the ASTM International (ASTM) Method E1739-95 (NAC, 2008; ASTM, 1995). It is designed to provide a set of consistent standards for chemical and radiological corrective actions.

Spray drift reduction test method correlation

USDA-ARS?s Scientific Manuscript database

ASTM Standard E609 Terminology Relating to Pesticides defines drift as “The physical movement of an agrochemical through the air at the time of application or soon thereafter to any non or off target site.” Since there are many commercial tank mix adjuvants designed to reduce spray drift, ASTM esta...

30 CFR 75.1900 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... serve its intended function for 1 hour when subjected to a fire test incorporating an ASTM E119-88 time/temperature heat input, or equivalent. The publication ASTM E119-88 “Standard Test Methods for Fire Tests of... Wilson Blvd., Room 2352, Arlington, Virginia 22209-3939; or at the National Archives and Records...

30 CFR 75.1900 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... serve its intended function for 1 hour when subjected to a fire test incorporating an ASTM E119-88 time/temperature heat input, or equivalent. The publication ASTM E119-88 “Standard Test Methods for Fire Tests of... Wilson Blvd., Room 2352, Arlington, Virginia 22209-3939; or at the National Archives and Records...

30 CFR 75.1900 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... serve its intended function for 1 hour when subjected to a fire test incorporating an ASTM E119-88 time/temperature heat input, or equivalent. The publication ASTM E119-88 “Standard Test Methods for Fire Tests of... Wilson Blvd., Room 2352, Arlington, Virginia 22209-3939; or at the National Archives and Records...

30 CFR 75.1900 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... serve its intended function for 1 hour when subjected to a fire test incorporating an ASTM E119-88 time/temperature heat input, or equivalent. The publication ASTM E119-88 “Standard Test Methods for Fire Tests of... Wilson Blvd., Room 2352, Arlington, Virginia 22209-3939; or at the National Archives and Records...

Composite material making from empty fruit bunches of palm oil (EFB) and Ijuk (Arengapinnata) using plastic bottle waste as adhesives

NASA Astrophysics Data System (ADS)

Rihayat, T.; Salim, S.; Audina, N.; Khan, N. S. P.; Zaimahwati; Sami, M.; Yunus, M.; Salisah, Z.; Alam, P. N.; Saifuddin; Yusuf, I.

2018-03-01

Reviewed from the current technological required a new methods to capable offering a high profit value without overriding the quality. The development of composite technology is now beginning to shift from traditional composite materials based petroleum to natural fibers composite. In the present study, aim to made specimens using natural fibers in form of EFB as a composite reinforcedment with Polyethylene Terephtalate (PET) derived from Plastic bottles waste as matrix with mixed composition parameters and time-tolerance in the mixing process to build a biocomposite material. The characterization of mechanical properties includes tensile test (ASTM D638-01) and bending test (ASTM D790-02) followed by thermal analysis using Thermogravimetric Analysis (TGA), and morphological analysis using scanning electron microscope (SEM). The analysis effect of EFB, Ijuk and PET mixtures on the composite matrix is very influential with mechanical properties characterization, including tensile test and bending strength. The results demonstrated that from the sample named : 50 : 25: 25, hybrid composites showed improved properties such as tensile strength of 167 MPa while the 90:05:05 based composites exhibited tensile strength values of 30 MPa, respectively. In term the flexural test the best result of composition on the properties with 10 minutes duration time its load value 7,5 Mpa for 80:10:10.

Sterility and Safety Validation for Transport Packaging of Organs and Tissues.

PubMed

Cobos, M; Trunzo, L; Vogt, M V; Romero, O; Anessi, C; Pachado, J; Ciávaro, M N; Horak, C; Bacqué, M C

2018-03-01

The bags used in the transport of organs and tissues must be sterile, nontoxic, pyrogen free, and must serve as a barrier throughout their useful life. The goal of this study was to show the sterility, safety, and functionality of the bags subjected to irradiation, through validated procedures and techniques. The selected sterilization method was the use of gamma radiation. The sterilization dose was determined based on validated standards for the sterilization of medical products, ISO 11137-2: 2013 and ISO/TS 13004: 2013, using the Verification Dose Maximum method on samples belonging to 3 manufacturing lots. The ISO 10993-5: 2009 standard was used in the cytotoxicity tests, by means of extracts test and quantitative technique of MTT, 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide. The tests to determine the expiration date of the kit were performed by ASTM F1980, accelerated aging, and ASTM D3078 to evaluate hermeticity. The irradiation dose validated to reach the required sterility safety level was 22.5 kGy. The constituent materials and the sterilization method do not generated cellular toxicity, and the product was not modified during the simulated time of 5 years. Sterilization by irradiation is a method that leaves no residue, does not harm the properties of the material because it is conducted in cold, and as the sterilizing agent, the energy absorbed by the product is highly penetrating and can be treated in its final packaging, with no risk of postcontamination. It is for this reason that it is prioritized over other methods of sterilization. Copyright © 2017 Elsevier Inc. All rights reserved.

Outgassing Data for Selecting Spacecraft Materials. Revision 4

NASA Technical Reports Server (NTRS)

Walter, Neil A.; Scialdone, John J.

1997-01-01

Outgassing data, derived from tests at 398 K (125 C) for 24 hours in a vacuum as per ASTM E 595-84, have been compiled for numerous materials for spacecraft use. The data presented are the total mass loss (TML) and the collected volatile condensable materials (CVCM). The various materials are compiled by likely usage and alphabetically.

Mechanics Aspects of Microcrack Growth in Inconel 718-Implications for Engine Retirement for Cause Analysis

DTIC Science & Technology

1985-03-18

Implications Obtaining crack growth behavior for cracks rO.5 mm long ( deep ) requires tracking procedures other than typically used methods. ASTM stand...Kmx. When helpful, relevant fractography is included. Where reference is made to the long crack trend, the results presented in Figure 12(b) for the... learned is that continuum fracture mechanics must be applied with caution in dealing with coarse-grained high-strength materials. That is, rp/a, based on

FUELS IN SOIL TEST KIT: FIELD USE OF DIESEL DOG SOIL TEST KITS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Susan S. Sorini; John F. Schabron; Joseph F. Rovani, Jr.

Western Research Institute (WRI) has developed a new commercial product ready for technology transfer, the Diesel Dog{reg_sign} Portable Soil Test Kit, for performing analysis of fuel-contaminated soils in the field. The technology consists of a method developed by WRI (U.S. Patents 5,561,065 and 5,976,883) and hardware developed by WRI that allows the method to be performed in the field (patent pending). The method is very simple and does not require the use of highly toxic reagents. The aromatic components in a soil extract are measured by absorption at 254 nm with a field-portable photometer. WRI added significant value to themore » technology by taking the method through the American Society for Testing and Materials (ASTM) approval and validation processes. The method is designated as ASTM Method D 5831-96, Standard Test Method for Screening Fuels in Soils. This ASTM designation allows the method to be used for federal compliance activities. In June 2001, the Diesel Dog technology won an American Chemical Society Regional Industrial Innovations Award. To gain field experience with the new technology, Diesel Dog kits have been used for a variety of site evaluation and cleanup activities. Information gained from these activities has led to improvements in hardware configurations and additional insight into correlating Diesel Dog results with results from laboratory methods. The Wyoming Department of Environmental Quality (DEQ) used Diesel Dog Soil Test Kits to guide cleanups at a variety of sites throughout the state. ENSR, of Acton, Massachusetts, used a Diesel Dog Portable Soil Test Kit to evaluate sites in the Virgin Islands and Georgia. ChemTrack and the U.S. Army Corps of Engineers successfully used a test kit to guide excavation at an abandoned FAA fuel-contaminated site near Fairbanks, Alaska. Barenco, Inc. is using a Diesel Dog Portable Soil Test Kit for site evaluations in Canada. A small spill of diesel fuel was cleaned up in Laramie, Wyoming using a Diesel Dog Soil Test Kit.« less

Standard Methods for Unnotched Tension Testing of Textile Composites

NASA Technical Reports Server (NTRS)

Portanova, M. A.

1995-01-01

An investigation was conducted by researchers at the Boeing Defense & Space Group to investigate the effects of specimen sizing on several braided textile materials. Test results from this and other test programs were compared in an effort to determine what effect, if any, specimen size has on elastic property measurements of unnotched tension test. In general, the unnotched tensile strength of 2-D braids was found to be insensitive to specimen width, length, or thickness effects. The results from this study suggest that standard testing methods used for tape materials may be sufficient for tension testing of textile composite materials. Specifically, the straight sided specimen geometry described in ASTM 3034, and used by Boeing, should provide acceptable results. Further experiments performed at Boeing and by other investigators on other textile architectures suggest similar results. Although specimen size studies were not conducted, failing stresses varied on the same order as those obtained with the 2-D materials. This suggests that the accuracy of the results were consistent with those obtained with the 2-D materials.

Heat treated 9 Cr-1 Mo steel material for high temperature application

DOEpatents

Jablonski, Paul D.; Alman, David; Dogan, Omer; Holcomb, Gordon; Cowen, Christopher

2012-08-21

The invention relates to a composition and heat treatment for a high-temperature, titanium alloyed, 9 Cr-1 Mo steel exhibiting improved creep strength and oxidation resistance at service temperatures up to 650.degree. C. The novel combination of composition and heat treatment produces a heat treated material containing both large primary titanium carbides and small secondary titanium carbides. The primary titanium carbides contribute to creep strength while the secondary titanium carbides act to maintain a higher level of chromium in the finished steel for increased oxidation resistance, and strengthen the steel by impeding the movement of dislocations through the crystal structure. The heat treated material provides improved performance at comparable cost to commonly used high-temperature steels such as ASTM P91 and ASTM P92, and requires heat treatment consisting solely of austenization, rapid cooling, tempering, and final cooling, avoiding the need for any hot-working in the austenite temperature range.

Acidity of biomass fast pyrolysis bio-oils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oasmaa, Anja; Elliott, Douglas C.; Korhonen, Jaana

2010-12-17

The use of the TAN method for measuring the acidity of biomass fast pyrolysis bio-oil was evaluated. Suggestions for carrying out the analysis have been made. The TAN method by ASTM D664 or D3339 can be used for measuring the acidity of fast pyrolysis bio-oils and their hydrotreating products. The main difference between the methods is that ASTM D664 is specified for higher TAN values than ASTM D3339. Special focus should be placed on the interpretation of the TAN curves because they differ significantly from those of mineral oils. The curve for bio-oils is so gentle that the automatic detectionmore » may not observe the end point properly and derivatization should be used. The acidity of fast pyrolysis bio-oils is mainly derived (60-70%) from volatile acids. Other groups of compounds in fast pyrolysis bio-oils that influence acidity include phenolics, fatty and resin acids, and hydroxy acids.« less

Evaluation of the flexibility of protective gloves.

PubMed

Harrabi, Lotfi; Dolez, Patricia I; Vu-Khanh, Toan; Lara, Jaime

2008-01-01

Two mechanical methods have been developed for the characterization of the flexibility of protective gloves, a key factor affecting their degree of usefulness for workers. The principle of the first method is similar to the ASTM D 4032 standard relative to fabric stiffness and simulates the deformations encountered by gloves that are not tight fitted to the hand. The second method characterizes the flexibility of gloves that are worn tight fitted. Its validity was theoretically verified for elastomer materials. Both methods should prove themselves as valuable tools for protective glove manufacturers, allowing for the characterization of their existing products in terms of flexibility and the development of new ones better fitting workers' needs.

46 CFR 114.600 - Incorporation by reference.

Code of Federal Regulations, 2010 CFR

2010-10-01

... for Building and Classing Steel Vessels Under 61 Meters (200 Feet) in Length, 1983 116.300 Rules for...) Apparatus 114.400 ASTM B 122/B 122M-95, Standard Specification for Copper-Nickel-Tin Alloy , Copper-Nickel..., Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 114.400 ASTM D 635-97, Standard...

40 CFR 63.14 - Incorporations by reference.

Code of Federal Regulations, 2013 CFR

2013-07-01

...., Washington, DC, and at the EPA Library (MD-35), U.S. EPA, Research Triangle Park, North Carolina. For... (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428-2959, Telephone (610... following Web site: http://www.proquest.com. (1) ASTM D523-89, Standard Test Method for Specular Gloss, IBR...

40 CFR 63.14 - Incorporations by reference.

Code of Federal Regulations, 2012 CFR

2012-07-01

...., Washington, DC, and at the EPA Library (MD-35), U.S. EPA, Research Triangle Park, North Carolina. For... (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428-2959; or ProQuest, 300 North Zeeb Road, Ann Arbor, MI 48106. (1) ASTM D523-89, Standard Test Method for Specular Gloss, IBR...

77 FR 30976 - Hazardous Materials: Miscellaneous Petitions for Rulemaking (RRR)

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-24

... in specifications for resins used in the manufacture of plastic drums and Intermediate Bulk...-06, Standard Specification for Polyethylene Plastics Molding and Extrusion Materials, discussed in....801(c)(7) to ASTM D4976-06 Standard Specification for Polyethylene Plastics Molding and Extrusion...

46 CFR 160.176-8 - Materials.

Code of Federal Regulations, 2013 CFR

2013-10-01

... cartridge), be 410 stainless steel, have salt water and salt air corrosion characteristics equal or superior... material. (6) Corrosion resistance. Each metal component must— (i) Be galvanically compatible with each... on any surface after 720 hours of salt spray testing according to ASTM B 117 (incorporated by...

46 CFR 160.176-8 - Materials.

Code of Federal Regulations, 2012 CFR

2012-10-01

... cartridge), be 410 stainless steel, have salt water and salt air corrosion characteristics equal or superior... material. (6) Corrosion resistance. Each metal component must— (i) Be galvanically compatible with each... on any surface after 720 hours of salt spray testing according to ASTM B 117 (incorporated by...

46 CFR 160.176-8 - Materials.

Code of Federal Regulations, 2014 CFR

2014-10-01

... cartridge), be 410 stainless steel, have salt water and salt air corrosion characteristics equal or superior... material. (6) Corrosion resistance. Each metal component must— (i) Be galvanically compatible with each... on any surface after 720 hours of salt spray testing according to ASTM B 117 (incorporated by...

Porosity of Self-Compacting Concrete (SCC) incorporating high volume fly ash

NASA Astrophysics Data System (ADS)

Kristiawan, S. A.; Sunarmasto; Murti, G. Y.

2017-02-01

Degradation of concrete could be triggered by the presence of aggressive agents from the environment into the body of concrete. The penetration of these agents is influenced by the pore characteristics of the concrete. Incorporating a pozzolanic material such as fly ash could modify the pore characteristic of the concrete. This research aims to investigate the influence of incorporating fly ash at high volume level on the porosity of Self-Compacting Concrete (SCC). Laboratory investigations were carried out following the ASTM C642 for measuring density and volume of permeable pores (voids) of the SCC with varying fly ash contents (50-70% by weight of total binder). In addition, a measurement of permeable voids by saturation method was carried out to obtain an additional volume of voids that could not be measured by the immersion and boiling method of ASTM C642. The results show that the influence of fly ash content on the porosity appears to be dependent on age of SCC. At age less than 56 d, fly ash tends to cause an increase of voids but at 90 d of age it reduces the pores. The additional pores that can be penetrated by vacuum saturation method counts about 50% of the total voids.

Adulteration of diesel/biodiesel blends by vegetable oil as determined by Fourier transform (FT) near infrared spectrometry and FT-Raman spectroscopy.

PubMed

Oliveira, Flavia C C; Brandão, Christian R R; Ramalho, Hugo F; da Costa, Leonardo A F; Suarez, Paulo A Z; Rubim, Joel C

2007-03-28

In this work it has been shown that the routine ASTM methods (ASTM 4052, ASTM D 445, ASTM D 4737, ASTM D 93, and ASTM D 86) recommended by the ANP (the Brazilian National Agency for Petroleum, Natural Gas and Biofuels) to determine the quality of diesel/biodiesel blends are not suitable to prevent the adulteration of B2 or B5 blends with vegetable oils. Considering the previous and actual problems with fuel adulterations in Brazil, we have investigated the application of vibrational spectroscopy (Fourier transform (FT) near infrared spectrometry and FT-Raman) to identify adulterations of B2 and B5 blends with vegetable oils. Partial least square regression (PLS), principal component regression (PCR), and artificial neural network (ANN) calibration models were designed and their relative performances were evaluated by external validation using the F-test. The PCR, PLS, and ANN calibration models based on the Fourier transform (FT) near infrared spectrometry and FT-Raman spectroscopy were designed using 120 samples. Other 62 samples were used in the validation and external validation, for a total of 182 samples. The results have shown that among the designed calibration models, the ANN/FT-Raman presented the best accuracy (0.028%, w/w) for samples used in the external validation.

Proposed Reference Spectral Irradiance Standards to Improve Photovoltaic Concentrating System Design and Performance Evaluation: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Myers, D. R.; Emery, K. E.; Gueymard, C.

2002-05-01

This conference paper describes the American Society for Testing and Materials (ASTM), the International Electrotechnical Commission (IEC), and the International Standards Organization (ISO) standard solar terrestrial spectra (ASTM G-159, IEC-904-3, ISO 9845-1) provide standard spectra for photovoltaic performance applications. Modern terrestrial spectral radiation models and knowledge of atmospheric physics are applied to develop suggested revisions to update the reference spectra. We use a moderately complex radiative transfer model (SMARTS2) to produce the revised spectra. SMARTS2 has been validated against the complex MODTRAN radiative transfer code and spectral measurements. The model is proposed as an adjunct standard to reproduce the referencemore » spectra. The proposed spectra represent typical clear sky spectral conditions associated with sites representing reasonable photovoltaic energy production and weathering and durability climates. The proposed spectra are under consideration by ASTM.« less

The Effect of Boronizing on Metallic Alloys for Automotive Applications

NASA Astrophysics Data System (ADS)

Petrova, Roumiana S.; Suwattananont, Naruemon; Samardzic, Veljko

2008-06-01

In this study the wear resistance, corrosion resistance, and oxidation resistance of boronized metallic alloys were investigated. Thermochemical treatment was performed by powder pack boronizing process at temperature 850-950 °C for 4 h. Saw-tooth morphology and smooth interface microstructures were observed with an optical microscope; microhardness was measured across the coating depth. The phases present in the boron coatings depend on the substrate material. High-temperature oxidation resistance was investigated and it was found that boron coating on ferrous alloys can resist temperatures up to 800 °C. The corrosion resistance of the boronized samples was improved and the corrosion rate was calculated for boronized and plain specimens. Wear testing was conducted by following the procedures of ASTM G99, ASTM D2526, and ASTM D4060. The obtained experimental results revealed that boronizing significantly improves the wear-resistance, corrosion-resistance, and oxidation resistance of metallic alloys.

SPF Full-scale emissions test method development status ...

EPA Pesticide Factsheets

This is a non-technical presentation that is intended to inform ASTM task group members about our intended approach to full-scale emissions testing that includes the application of spray foam in an environmental chamber. The presentation describes the approach to emissions characterization, types of measurement systems employed, and expected outcomes from the planned tests. Purpose of this presentation is to update the ASTM D22.05 work group regarding status of our full-scale emissions test method development.

24 CFR 3280.604 - Materials.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Seamless Red Brass Pipe, Standard Sizes—ASTM B43-91. Cast Bronze Threaded Fittings, Classes 125 and 250... Food Waste Disposer Units—ASSE 1008-1986. Performance Requirements for Temperature Activated Mixing...

40 CFR 89.3 - Acronyms and abbreviations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... ASME American Society of Mechanical Engineers ASTM American Society for Testing and Materials CAA Clean... Oxygen OEM Original equipment manufacturer PM Particulate matter SAE Society of Automotive Engineers SEA...

40 CFR 89.3 - Acronyms and abbreviations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... ASME American Society of Mechanical Engineers ASTM American Society for Testing and Materials CAA Clean... Oxygen OEM Original equipment manufacturer PM Particulate matter SAE Society of Automotive Engineers SEA...

ASTM International Workshop on Standards & Measurements for Tissue Engineering Scaffolds

PubMed Central

Simon, Carl G.; Yaszemski, Michael J.; Ratcliffe, Anthony; Tomlins, Paul; Luginbuehl, Reto; Tesk, John A.

2016-01-01

The “Workshop on Standards & Measurements for Tissue Engineering Scaffolds” was held on May 21, 2013 in Indianapolis, IN and was sponsored by the ASTM International (ASTM). The purpose of the workshop was to identify the highest priority items for future standards work for scaffolds used in the development and manufacture of tissue engineered medical products (TEMPs). Eighteen speakers and 78 attendees met to assess current scaffold standards and to prioritize needs for future standards. A key finding was that the ASTM TEMPs subcommittees (F04.41-46) have many active “guide” documents for educational purposes, but that few standard “test methods” or “practices” have been published. Overwhelmingly, the most clearly identified need was standards for measuring the structure of scaffolds, followed by standards for biological characterization, including in vitro testing, animal models and cell-material interactions. The third most pressing need was to develop standards for assessing the mechanical properties of scaffolds. Additional needs included standards for assessing scaffold degradation, clinical outcomes with scaffolds, effects of sterilization on scaffolds, scaffold composition and drug release from scaffolds. Discussions also highlighted the need for additional scaffold reference materials and the need to use them for measurement traceability. Finally, dialogue emphasized the needs to promote the use of standards in scaffold fabrication, characterization, and commercialization and to assess the use and impact of standards in the TEMPs community. Many scaffold standard needs have been identified and focus should now turn to generating these standards to support the use of scaffolds in TEMPs. PMID:25220952

40 CFR 63.14 - Incorporations by reference.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (MD-35), U.S. EPA, Research Triangle Park, North Carolina. For information on the availability of this..., Post Office Box C700, West Conshohocken, PA 19428-2959; or ProQuest, 300 North Zeeb Road, Ann Arbor, MI 48106. (1) ASTM D523-89, Standard Test Method for Specular Gloss, IBR approved for § 63.782. (2) ASTM...

40 CFR 75.6 - Incorporation by reference.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., phone: 610-832-9585, http://www.astm.org/DIGITAL_LIBRARY/index.shtml. (1) ASTM D129-00, Standard Test... Information Reference Unit of the U.S. EPA, 401 M St., SW., Washington, DC and at the Library (MD-35), U.S... D4052-96 (Reapproved 2002), Standard Test Method for Density and Relative Density of Liquids by Digital...

40 CFR 75.6 - Incorporation by reference.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., phone: 610-832-9585, http://www.astm.org/DIGITAL_LIBRARY/index.shtml. (1) ASTM D129-00, Standard Test... Information Reference Unit of the U.S. EPA, 401 M St., SW., Washington, DC and at the Library (MD-35), U.S... D4052-96 (Reapproved 2002), Standard Test Method for Density and Relative Density of Liquids by Digital...

40 CFR 75.6 - Incorporation by reference.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., phone: 610-832-9585, http://www.astm.org/DIGITAL_LIBRARY/index.shtml. (1) ASTM D129-00, Standard Test... Information Reference Unit of the U.S. EPA, 401 M St., SW., Washington, DC and at the Library (MD-35), U.S... D4052-96 (Reapproved 2002), Standard Test Method for Density and Relative Density of Liquids by Digital...

40 CFR 75.6 - Incorporation by reference.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., phone: 610-832-9585, http://www.astm.org/DIGITAL_LIBRARY/index.shtml. (1) ASTM D129-00, Standard Test... Information Reference Unit of the U.S. EPA, 401 M St., SW., Washington, DC and at the Library (MD-35), U.S... D4052-96 (Reapproved 2002), Standard Test Method for Density and Relative Density of Liquids by Digital...

Hardware cleanliness methodology and certification

NASA Technical Reports Server (NTRS)

Harvey, Gale A.; Lash, Thomas J.; Rawls, J. Richard

1995-01-01

Inadequacy of mass loss cleanliness criteria for selection of materials for contamination sensitive uses, and processing of flight hardware for contamination sensitive instruments is discussed. Materials selection for flight hardware is usually based on mass loss (ASTM E-595). However, flight hardware cleanliness (MIL 1246A) is a surface cleanliness assessment. It is possible for materials (e.g. Sil-Pad 2000) to pass ASTM E-595 and fail MIL 1246A class A by orders of magnitude. Conversely, it is possible for small amounts of nonconforming material (Huma-Seal conformal coating) to not present significant cleanliness problems to an optical flight instrument. Effective cleaning (precleaning, precision cleaning, and ultra cleaning) and cleanliness verification are essential for contamination sensitive flight instruments. Polish cleaning of hardware, e.g. vacuum baking for vacuum applications, and storage of clean hardware, e.g. laser optics, is discussed. Silicone materials present special concerns for use in space because of the rapid conversion of the outgassed residues to glass by solar ultraviolet radiation and/or atomic oxygen. Non ozone depleting solvent cleaning and institutional support for cleaning and certification are also discussed.

Resistivity Measurement by Dual-Configuration Four-Probe Method

NASA Astrophysics Data System (ADS)

Yamashita, Masato; Nishii, Toshifumi; Mizutani, Hiroya

2003-02-01

The American Society for Testing and Materials (ASTM) Committee has published a new technique for the measurement of resistivity which is termed the dual-configuration four-probe method. The resistivity correction factor is the function of only the data which are obtained from two different electrical configurations of the four probes. The measurement of resistivity and sheet resistance are performed for graphite rectangular plates and indium tin oxide (ITO) films by the conventional four-probe method and the dual-configuration four-probe method. It is demonstrated that the dual-configuration four-probe method which includes a probe array with equal separations of 10 mm can be applied to specimens having thicknesses up to 3.7 mm if a relative resistivity difference up to 5% is allowed.

Materials Outgassing Rate Decay in Vacuum at Isothermal Conditions

NASA Technical Reports Server (NTRS)

Huang, Alvin Y.; Kastanas, George N.; Kramer, Leonard; Soares, Carlos E.; Mikatarian, Ronald R.

2016-01-01

As a laboratory for scientific research, the International Space Station has been in Low Earth Orbit for nearly 20 years and is expected to be on-orbit for another 10 years. The ISS has been maintaining a relatively pristine contamination environment for science payloads. Materials outgassing induced contamination is currently the dominant source for sensitive surfaces on ISS and modeling the outgassing rate decay over a 20 to 30 year period is challenging. Materials outgassing is described herein as a diffusion-reaction process using ASTM E 1559 rate data. The observation of -1/2 (diffusion) or non-integers (reaction limited) as rate decay exponents for common ISS materials indicate classical reaction kinetics is unsatisfactory in modeling materials outgassing. Non-randomness of reactant concentrations at the interface is the source of this deviation from classical reaction kinetics. A diffusion limited decay was adopted as the result of the correlation of the contaminant layer thicknesses on returned ISS hardware, the existence of high outgassing silicone exhibiting near diffusion limited decay, and the confirmation of non-depleted material after ten years in the Low Earth Orbit.Keywords: Materials Outgassing, ASTM E 1559, Reaction Kinetics, Diffusion, Space Environments Effects, Contamination

Evaluation of a standard test method for screening fuels in soils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sorini, S.S.; Schabron, J.F.

1996-12-31

A new screening method for fuel contamination in soils was recently developed as American Society for Testing and Materials (ASTM) Method D-5831-95, Standard Test Method for Screening Fuels in Soils. This method uses low-toxicity chemicals and can be sued to screen organic- rich soils, as well as being fast, easy, and inexpensive to perform. Fuels containing aromatic compounds, such as diesel fuel and gasoline, as well as other aromatic-containing hydrocarbon materials, such as motor oil, crude oil, and cola oil, can be determined. The screening method for fuels in soils was evaluated by conducting a Collaborative study on the method.more » In the Collaborative study, a sand and an organic soil spiked with various concentrations of diesel fuel were tested. Data from the Collaborative study were used to determine the reproducibility (between participants) and repeatability (within participants) precision of the method for screening the test materials. The Collaborative study data also provide information on the performance of portable field equipment (patent pending) versus laboratory equipment for performing the screening method and a comparison of diesel concentration values determined using the screening method versus a laboratory method.« less

Cryogenic insulation standard data and methodologies

NASA Astrophysics Data System (ADS)

Demko, J. A.; Fesmire, J. E.; Johnson, W. L.; Swanger, A. M.

2014-01-01

Although some standards exist for thermal insulation, few address the sub-ambient temperature range and cold-side temperatures below 100 K. Standards for cryogenic insulation systems require cryostat testing and data analysis that will allow the development of the tools needed by design engineers and thermal analysts for the design of practical cryogenic systems. Thus, this critically important information can provide reliable data and methodologies for industrial efficiency and energy conservation. Two Task Groups have been established in the area of cryogenic insulation systems Under ASTM International's Committee C16 on Thermal Insulation. These are WK29609 - New Standard for Thermal Performance Testing of Cryogenic Insulation Systems and WK29608 - Standard Practice for Multilayer Insulation in Cryogenic Service. The Cryogenics Test Laboratory of NASA Kennedy Space Center and the Thermal Energy Laboratory of LeTourneau University are conducting Inter-Laboratory Study (ILS) of selected insulation materials. Each lab carries out the measurements of thermal properties of these materials using identical flat-plate boil-off calorimeter instruments. Parallel testing will provide the comparisons necessary to validate the measurements and methodologies. Here we discuss test methods, some initial data in relation to the experimental approach, and the manner reporting the thermal performance data. This initial study of insulation materials for sub-ambient temperature applications is aimed at paving the way for further ILS comparative efforts that will produce standard data sets for several commercial materials. Discrepancies found between measurements will be used to improve the testing and data reduction techniques being developed as part of the future ASTM International standards.

Microstructural Evaluation of Forging Parameters for Superalloy Disks

NASA Technical Reports Server (NTRS)

Falsey, John R.

2004-01-01

Forgings of nickel base superalloy were formed under several different strain rates and forging temperatures. Samples were taken from each forging condition to find the ASTM grain size, and the as large as grain (ALA). The specimens were mounted in bakelite, polished, etched and then optical microscopy was used to determine grain size. The specimens ASTM grain sizes from each forging condition were plotted against strain rate, forging temperature, and presoak time. Grain sizes increased with increasing forging temperature. Grain sizes also increased with decreasing strain rates and increasing forging presoak time. The ALA had been determined from each forging condition using the ASTM standard method. Each ALA was compared with the ASTM grain size of each forging condition to determine if the grain sizes were uniform or not. The forging condition of a strain rate of .03/sec and supersolvus heat treatment produced non uniform grains indicated by critical grain growth. Other anomalies are noted as well.

49 CFR 171.7 - Reference material.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., PHH-10, 1200 New Jersey Avenue, SE., Washington, DC 20590-0001. For information on the availability of... Archives and Records Administration (NARA). For information on the availability of this material at NARA... Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service 173.5b. ASTM A 240/A...

46 CFR 54.05-5 - Toughness test specimens.

Code of Federal Regulations, 2011 CFR

2011-10-01

... V-notch tests shall be conducted in accordance with ASTM Specification E 23 (incorporated by... for that thickness shall be cut centered at the material's mid-thickness. For materials thicker than 1/2-inch, full size Charpy specimens shall be cut centered at a location as near as practicable to a...

40 CFR Table B-2 to Subpart B of... - Test Atmospheres

Code of Federal Regulations, 2013 CFR

2013-07-01

... of ASTM Standards, American Society for Testing and Materials, 1916 Race St., Philadelphia, PA..., American Society for Testing and Materials, 1916 Race St., Philadelphia, PA 19103. ... 40 Protection of Environment 6 2013-07-01 2013-07-01 false Test Atmospheres B Table B-2 to Subpart...

40 CFR Table B-2 to Subpart B of... - Test Atmospheres

Code of Federal Regulations, 2014 CFR

2014-07-01

... of ASTM Standards, American Society for Testing and Materials, 1916 Race St., Philadelphia, PA..., American Society for Testing and Materials, 1916 Race St., Philadelphia, PA 19103. ... 40 Protection of Environment 6 2014-07-01 2014-07-01 false Test Atmospheres B Table B-2 to Subpart...

40 CFR Table B-2 to Subpart B of... - Test Atmospheres

Code of Federal Regulations, 2012 CFR

2012-07-01

... of ASTM Standards, American Society for Testing and Materials, 1916 Race St., Philadelphia, PA..., American Society for Testing and Materials, 1916 Race St., Philadelphia, PA 19103. ... 40 Protection of Environment 6 2012-07-01 2012-07-01 false Test Atmospheres B Table B-2 to Subpart...

Making Materials Science and Engineering Data More Valuable Research Products (Postprint)

DTIC Science & Technology

2014-09-12

uncertainties in the publishing market - place.b Also, there is a possibility that some for-profit publishers could try to restrict access to digital...Kaufman JG, Glatzman JS (eds) Computerization and networking of materials databases: Second Volume, ASTM STP 1106. American Society for Testing and

46 CFR 160.176-4 - Incorporation by reference.

Code of Federal Regulations, 2011 CFR

2011-10-01

... the sections affected are: American Society for Testing and Materials (ASTM) 100 Barr Harbor Drive... Institute of Standards and Technology (NIST) (formerly National Bureau of Standards) C/O Superintendent of...

46 CFR 160.176-4 - Incorporation by reference.

Code of Federal Regulations, 2010 CFR

2010-10-01

... the sections affected are: American Society for Testing and Materials (ASTM) 100 Barr Harbor Drive... Institute of Standards and Technology (NIST) (formerly National Bureau of Standards) C/O Superintendent of...

Standardization Efforts for Mechanical Testing and Design of Advanced Ceramic Materials and Components

NASA Technical Reports Server (NTRS)

Salem, Jonathan A.; Jenkins, Michael G.

2003-01-01

Advanced aerospace systems occasionally require the use of very brittle materials such as sapphire and ultra-high temperature ceramics. Although great progress has been made in the development of methods and standards for machining, testing and design of component from these materials, additional development and dissemination of standard practices is needed. ASTM Committee C28 on Advanced Ceramics and ISO TC 206 have taken a lead role in the standardization of testing for ceramics, and recent efforts and needs in standards development by Committee C28 on Advanced Ceramics will be summarized. In some cases, the engineers, etc. involved are unaware of the latest developments, and traditional approaches applicable to other material systems are applied. Two examples of flight hardware failures that might have been prevented via education and standardization will be presented.

Application of sandwich honeycomb carbon/glass fiber-honeycomb composite in the floor component of electric car

NASA Astrophysics Data System (ADS)

Sukmaji, I. C.; Wijang, W. R.; Andri, S.; Bambang, K.; Teguh, T.

2017-01-01

Nowadays composite is a superior material used in automotive component due to its outstanding mechanical behavior. The sandwich polypropylene honeycomb core with carbon/glass fiber composite skin (SHCG) as based material in a floor component of electric car application is investigated in the present research. In sandwich structure form, it can absorb noise better compare with the conventional material [1]. Also in present paper, Finite Element Analysis (FEA) of SHCG as based material for floor component of the electric car is analyzed. The composite sandwich is contained with a layer uniform carbon fiber and mixing non-uniform carbon-glass fiber in upper and lower skin. Between skins of SHCG are core polypropylene honeycomb that it have good flexibility to form following dies profile. The variables of volume fraction ratio of carbon/glass fiber in SHCG skin are 20/80%, 30/70%, and 50/50%. The specimen of SHCG is tested using the universal testing machine by three points bending method refers to ASTM C393 and ASTM C365. The cross point between tensile strength to the volume fraction the mixing carbon/glass line and ratio cost line are the searched material with good mechanical performance and reasonable cost. The point is 30/70 volume fraction of carbon/glass fiber. The result of the testing experiment is become input properties of model structure sandwich in FEA simulation. FEA simulation approach is conducted to find critical strength and factor of complex safety geometry against varied distributed passenger loads of a floor component the electric car. The passenger loads variable are 80, 100, 150, 200, 250 and 300 kg.

Static and dynamic fatigue behavior of topology designed and conventional 3D printed bioresorbable PCL cervical interbody fusion devices.

PubMed

Knutsen, Ashleen R; Borkowski, Sean L; Ebramzadeh, Edward; Flanagan, Colleen L; Hollister, Scott J; Sangiorgio, Sophia N

2015-09-01

Recently, as an alternative to metal spinal fusion cages, 3D printed bioresorbable materials have been explored; however, the static and fatigue properties of these novel cages are not well known. Unfortunately, current ASTM testing standards used to determine these properties were designed prior to the advent of bioresorbable materials for cages. Therefore, the applicability of these standards for bioresorbable materials is unknown. In this study, an image-based topology and a conventional 3D printed bioresorbable poly(ε)-caprolactone (PCL) cervical cage design were tested in compression, compression-shear, and torsion, to establish their static and fatigue properties. Difficulties were in fact identified in establishing failure criteria and in particular determining compressive failure load. Given these limitations, under static loads, both designs withstood loads of over 650 N in compression, 395 N in compression-shear, and 0.25 Nm in torsion, prior to yielding. Under dynamic testing, both designs withstood 5 million (5M) cycles of compression at 125% of their respective yield forces. Geometry significantly affected both the static and fatigue properties of the cages. The measured compressive yield loads fall within the reported physiological ranges; consequently, these PCL bioresorbable cages would likely require supplemental fixation. Most importantly, supplemental testing methods may be necessary beyond the current ASTM standards, to provide more accurate and reliable results, ultimately improving preclinical evaluation of these devices. Copyright © 2015 Elsevier Ltd. All rights reserved.

Techniques for Reducing Thermal Contact Resistance in Steady-State Thermal Conductivity Measurements on Polymer Composites

NASA Astrophysics Data System (ADS)

Stacey, C.; Simpkin, A. J.; Jarrett, R. N.

2016-11-01

The National Physical Laboratory (NPL) has developed a new variation on the established guarded hot plate technique for steady-state measurements of thermal conductivity. This new guarded hot plate has been specifically designed for making measurements on specimens with a thickness that is practical for advanced industrial composite materials and applications. During the development of this new guarded hot plate, NPL carried out an experimental investigation into methods for minimising the thermal contact resistance between the test specimen and the plates of the apparatus. This experimental investigation included tests on different thermal interface materials for use in another NPL facility based on a commercial guarded heat flow meter apparatus conforming to standard ASTM E1530-11. The results show the effect of applying different quantities of the type of heat transfer compound suggested in ASTM E1530-11 (clause 10.7.3) and also the effect on thermal resistance of alternative types of thermal interface products. The optimum quantities of two silicone greases were determined, and a silicone grease filled with copper was found to offer the best combination of repeatability, small hysteresis effect and a low thermal contact resistance. However, two products based on a textured indium foil and pyrolytic graphite sheet were found to offer similar or better reductions in thermal contact resistance, but with quicker, easier application and the advantages of protecting the apparatus plates from damage and being useable with specimen materials that would otherwise absorb silicone grease.

10 CFR 431.303 - Materials incorporated by reference.

Code of Federal Regulations, 2011 CFR

2011-01-01

.... Department of Energy, Office of Energy Efficiency and Renewable Energy, Building Technologies Program, 6th..._standards/. Standards can be obtained from the sources listed below. (b) ASTM. American Society for Testing...

Autogenous accelerated curing of concrete cylinders. Part V, ASTM Cooperative Testing Program with additional emphasis on the influence of container and storage characteristics (supplemented by data on water bath curing from an earlier council project).

DOT National Transportation Integrated Search

1971-01-01

Concomitant with the Research Council's studies of accelerated curing for strength testing, Subcommittee II-i of ASTM Committee C-9 was developing and refining accelerated methods for standardization. This development included a cooperative testing p...

AM2 Brickwork Pattern Evaluation

DTIC Science & Technology

2016-12-01

pavement applications. Designation : D 6951. West Consho- hocken, PA: ASTM International. ASTM International. 2010a. Standard test method for in-place... design . This report provides test results for each evaluation and discussions comparing their perfor- mance to previous tests conducted under similar... designated by other authorized documents. DESTRUCTION NOTICE - For classified documents, follow the procedures in DOD5200.22-M, Industrial Security Manual

Waste Acceptance Testing of Secondary Waste Forms: Cast Stone, Ceramicrete and DuraLith

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mattigod, Shas V.; Westsik, Joseph H.; Chung, Chul-Woo

2011-08-12

To support the selection of a waste form for the liquid secondary wastes from WTP, Washington River Protection Solutions has initiated secondary-waste-form testing work at Pacific Northwest National Laboratory (PNNL). In anticipation of a down-selection process for a waste form for the Solidification Treatment Unit to be added to the ETF, PNNL is conducting tests on four candidate waste forms to evaluate their ability to meet potential waste acceptance criteria for immobilized secondary wastes that would be placed in the IDF. All three waste forms demonstrated compressive strengths above the minimum 3.45 MPa (500 psi) set as a target formore » cement-based waste forms. Further, none of the waste forms showed any significant degradation in compressive strength after undergoing thermal cycling (30 cycles in a 10 day period) between -40 C and 60 C or water immersion for 90 days. The three leach test methods are intended to measure the diffusion rates of contaminants from the waste forms. Results are reported in terms of diffusion coefficients and a leachability index (LI) calculated based on the diffusion coefficients. A smaller diffusion coefficient and a larger LI are desired. The NRC, in its Waste Form Technical Position (NRC 1991), provides recommendations and guidance regarding methods to demonstrate waste stability for land disposal of radioactive waste. Included is a recommendation to conduct leach tests using the ANS 16.1 method. The resulting leachability index (LI) should be greater than 6.0. For Hanford secondary wastes, the LI > 6.0 criterion applies to sodium leached from the waste form. For technetium and iodine, higher targets of LI > 9 for Tc and LI > 11 for iodine have been set based on early waste-disposal risk and performance assessment analyses. The results of these three leach tests conducted for a total time between 11days (ASTM C1308) to 90 days (ANS 16.1) showed: (1) Technetium diffusivity: ANSI/ANS 16.1, ASTM C1308, and EPA 1315 tests indicated that all the waste forms had leachability indices better than the target LI > 9 for technetium; (2) Rhenium diffusivity: Cast Stone 2M specimens, when tested using EPA 1315 protocol, had leachability indices better than the target LI > 9 for technetium based on rhenium as a surrogate for technetium. All other waste forms tested by ANSI/ANS 16.1, ASTM C1308, and EPA 1315 test methods had leachability indices that were below the target LI > 9 for Tc based on rhenium release. These studies indicated that use of Re(VII) as a surrogate for 99Tc(VII) in low temperature secondary waste forms containing reductants will provide overestimated diffusivity values for 99Tc. Therefore, it is not appropriate to use Re as a surrogate 99Tc in future low temperature waste form studies. (3) Iodine diffusivity: ANSI/ANS 16.1, ASTM C1308, and EPA 1315 tests indicated that the three waste forms had leachability indices that were below the target LI > 11 for iodine. Therefore, it may be necessary to use a more effective sequestering material than silver zeolite used in two of the waste forms (Ceramicrete and DuraLith); (4) Sodium diffusivity: All the waste form specimens tested by the three leach methods (ANSI/ANS 16.1, ASTM C1308, and EPA 1315) exceeded the target LI value of 6; (5) All three leach methods (ANS 16.1, ASTM C1308 and EPA 1315) provided similar 99Tc diffusivity values for both short-time transient diffusivity effects as well as long-term ({approx}90 days) steady diffusivity from each of the three tested waste forms (Cast Stone 2M, Ceramicrete and DuraLith). Therefore, any one of the three methods can be used to determine the contaminant diffusivities from a selected waste form.« less

78 FR 14836 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-07

... Production Act of 1993--ASTM International Standards Notice is hereby given that, on February 11, 2013... seq. (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between...

77 FR 34069 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-08

... Production Act of 1993--ASTM International Standards Notice is hereby given that, on May 11, 2012, pursuant... seq. (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between...

78 FR 64248 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-28

... Production Act of 1993--ASTM International Standards Notice is hereby given that, on September 16, 2013... seq. (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between May...

78 FR 35646 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-13

... Production Act of 1993--ASTM International Standards Notice is hereby given that, on May 10, 2013, pursuant... seq. (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between...

77 FR 61786 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-11

... Production Act of 1993--ASTM International Standards Notice is hereby given that, on September 10, 2012... seq. (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between May...

76 FR 34252 - Notice Pursuant to the National Cooperative Research and Production Act of 1993; ASTM...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-13

... Production Act of 1993; ASTM International Standards Notice is hereby given that, on May 11, 2011, pursuant... seq. (``the Act''), ASTM International Standards (``ASTM'') has filed written notifications.... Specifically, ASTM has provided an updated list of current, ongoing ASTM standards activities originating...

76 FR 12370 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-07

... Production Act of 1993--ASTM International Standards Notice is hereby given that, on February 4, 2011... seq. (``the Act''), ASTM International Standards (``ASTM'') has filed written notifications.... Specifically, ASTM has provided an updated list of current, ongoing ASTM standards activities originating...

78 FR 1884 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-09

... Production Act of 1993--ASTM International Standards Notice is hereby given that, on December 12, 2012... seq. (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between...

Influence of heat treatment on structural, mechanical and wear properties of crosslinked UHMWPE.

PubMed

Chiesa, R; Moscatelli, M; Giordano, C; Siccardi, F; Cigada, A

2004-01-01

New crosslinked ultra high molecular weight polyethylenes (UHMWPEs) have recently been developed, characterized and introduced in clinical applications. UHMWPE cross-linking treatments are very promising for reducing osteolysis induced by wear debris. The irradiation type, gamma or beta, the dosage and the thermal treatment performed during or following the irradiation process are all factors affecting polyethylene wear resistance. Thermal stabilization treatments performed after or during the irradiation process at a temperature above melting point (i.e. >130 degrees C) have been proven to effectively remove the free radicals generated during irradiation from UHMWPE, but their effect on the mechanical properties of UHMWPE are not completely clear. In addition to wear rate reduction, maintaining good mechanical properties is fundamental aspect in designing the new generation of crosslinked UHMWPE for artificial load bearing materials, especially considering the application in total knee replacements. In this study, we investigated the influence of different stabilization treatments, performed after gamma irradiation, on structural, wear and mechanical properties of UHMWPE. We performed four different stabilization treatments, with different temperatures and cooling rates, on 100 kGy gamma irradiated UHMWPE. Structural properties of UHMWPE were assessed by differential scanning calorimetry (DSC). To assess the mechanical performance of the materials, uni-axial tensile tests were performed according to the ASTM D638 standard, bi-axial tension performance was evaluated by small punch tests (ASTM F2183-02), toughness resistance was evaluated by the Izod method (ASTM F648), and cold flow resistance was analysed by a dynamic compressive test. Evaluation of wear resistance was by a multidirectional pin-on-disk screening machine. Materials considered were in "aged" and "non-aged" conditions. Results confirmed that cross-linking greatly enhances UHMWPE wear resistance, but introduces some detrimental effects on the mechanical properties. In this study, we found that the negative ef-fects on the mechanical properties of crosslinked UHMWPE can be modulated, to some extent, by choosing a thermal stabiliza-tion treatment at a correct temperature and cooling rate. (Journal of Applied Biomaterials & Biomechanics 2004; 2: 20-8).

46 CFR 160.032-1 - Applicable specifications.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Steel Castings, Carbon, Suitable for Fusion Welding for High-Temperature Service—160.032-3 (b) Copies on... ASTM from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA...

40 CFR 721.5310 - Neononanoic acid, ethenyl ester.

Code of Federal Regulations, 2010 CFR

2010-07-01

... accordance with the most current version of the American Society for Testing and Materials (ASTM) F739... control technology does not apply. Instead, if the waste stream containing the substance will be treated...

40 CFR 721.4215 - Hexanedioic acid, diethenyl ester.

Code of Federal Regulations, 2011 CFR

2011-07-01

... in accordance with the most current version of the American Society for Testing and Materials (ASTM... control technology does not apply. Instead, if the waste stream containing the substance will be treated...

40 CFR 721.4215 - Hexanedioic acid, diethenyl ester.

Code of Federal Regulations, 2010 CFR

2010-07-01

... in accordance with the most current version of the American Society for Testing and Materials (ASTM... control technology does not apply. Instead, if the waste stream containing the substance will be treated...

40 CFR 721.5310 - Neononanoic acid, ethenyl ester.

Code of Federal Regulations, 2011 CFR

2011-07-01

... accordance with the most current version of the American Society for Testing and Materials (ASTM) F739... control technology does not apply. Instead, if the waste stream containing the substance will be treated...

46 CFR 160.076-11 - Incorporation by reference.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Laboratories, Inc., 12 Laboratory Drive, Research Triangle Park, NC 27709-3995 (Phone (919) 549-1400; Facsimile... affected are as follows: American Society for Testing and Materials (ASTM) 100 Barr Harbor Drive, West...

Correlation of impression removal force with elastomeric impression material rigidity and hardness.

PubMed

Walker, Mary P; Alderman, Nick; Petrie, Cynthia S; Melander, Jennifer; McGuire, Jacob

2013-07-01

Difficult impression removal has been linked to high rigidity and hardness of elastomeric impression materials. In response to this concern, manufacturers have reformulated their materials to reduce rigidity and hardness to decrease removal difficulty; however, the relationship between impression removal and rigidity or hardness has not been evaluated. The purpose of this study was to determine if there is a positive correlation between impression removal difficulty and rigidity or hardness of current elastomeric impression materials. Light- and medium-body polyether (PE), vinylpolysiloxane (VPS), and hybrid vinyl polyether siloxane (VPES) impression materials were tested (n = 5 for each material/consistency/test method). Rigidity (elastic modulus) was measured via tensile testing of dumbbell-shaped specimens (Die C, ASTM D412). Shore A hardness was measured using disc specimens according to ASTM D2240-05 test specifications. Impressions were also made of a custom stainless steel model using a custom metal tray that could be attached to a universal tester to measure associated removal force. Within each impression material consistency, one-factor ANOVA and Tukey's post hoc analyses (α = 0.05) were used to compare rigidity, hardness, and removal force of the three types of impression materials. A Pearson's correlation (α = 0.05) was used to evaluate the association between impression removal force and rigidity or hardness. With medium-body materials, VPS exhibited significantly higher (p ≤ 0.05) rigidity and hardness than VPES or PE, while PE impressions required significantly higher (p ≤ 0.05) removal force than VPS or VPES impressions. With light-body materials, VPS again demonstrated significantly higher (p ≤ 0.05) hardness than VPES or PE, while the rigidity of the light-body materials did not significantly differ between materials (p > 0.05); however, just as with the medium-body materials, light-body PE impressions required significantly higher (p ≤ 0.05) removal force than VPS or VPES. Moreover, there was no positive correlation (p > 0.05) between impression removal force and rigidity or hardness with either medium- or light-body materials. The evidence suggests that high impression material rigidity and hardness are not predictors of impression removal difficulty. © 2013 by the American College of Prosthodontists.

76 FR 63658 - Notice Pursuant to the National Cooperative Research and Production Act of 1993; ASTM International

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-13

... Production Act of 1993; ASTM International Notice is hereby given that, on August 31, 2011, pursuant to.... (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with the..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between May...

75 FR 11196 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM International

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-10

... Production Act of 1993--ASTM International Notice is hereby given that, on February 16, 2010, pursuant to.... (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with the..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between May...

77 FR 14046 - Amended Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-08

... Research and Production Act of 1993--ASTM International Standards Notice is hereby given that, on February..., 15 U.S.C. 4301 et seq. (``the Act''), ASTM International Standards (``ASTM'') has filed written... circumstances. Specifically, ASTM has provided an updated list of current, ongoing ASTM standards activities...

77 FR 1085 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM International

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-09

... Production Act of 1993--ASTM International Notice is hereby given that, on December 5, 2011, pursuant to.... (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with the..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between...

75 FR 65657 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM International

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-26

... Production Act of 1993--ASTM International Notice is hereby given that, on September 23, 2010, pursuant to.... (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with the..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between May...

The characteristics of bioethanol fuel made of vegetable raw materials

NASA Astrophysics Data System (ADS)

Muhaji; Sutjahjo, D. H.

2018-01-01

The aim of this research is to identify the most potential vegetable raw as the material to make a bioethanol fuel as the alternative energy for gasoline. This study used experimental method. The high-level bioethanol was obtained through the process of saccharification, fermentation and stratified distillation. ASTM standards were used as the method of testing the chemical element (D 5501, D 1744, D 1688, D 512, D 2622, D 381), and physical test (D 1613, D 240, D 1298-99, D 445, and D 93). The result of the analysis showed that from the seven bioethanols being studied there is one bioethanol from Saccharum of icinarum linn that has physical and chemical properties close to the standard of bioethanol. Meanwhile, the others only meet some of the physical and chemical properties of the standard bioethanol.

Material Total Mass Loss in Vacuum Obtained From Various Outgassing Systems

NASA Technical Reports Server (NTRS)

Scialdone, John; Isaac, Peggy; Clatterbuck, Carroll; Hunkeler, Ronald

2000-01-01

Several instruments including the Cahn Microbalance, the Knudsen Cell, the micro-CVCM, and the vacuum Thermogravimetric Analyzer (TGA) were used in the testing of a graphite/epoxy (GR/EP) composite that is proposed for use as a rigidizing element of an inflatable deployment system. This GR/EP will be cured in situ. The purpose of this testing is to estimate the gaseous production resulting from the curing of the GR/EP composite, to predict the resulting pressure, and to calculate the required venting. Every test was conducted under vacuum at 125 degrees C for 24 hours. Upon comparison of the results, the ASTM E-595 was noted to have given readings that were consistently lower than those obtained using the other instruments, which otherwise provided similar results. The GR/EP was tested using several different geometric arrangements. This paper describes the analysis evaluating the molecular and continuum flow of the outgassing products issuing from the exit port of the ASTM E-595 system. The effective flow conductance provided by the physical dimensions of the vent passage of the ASTM E-595 system and that of the material sample among other factors were investigated to explain the reduced amount of outgassing released during the 24-hour test period.

Applications of Automation Methods for Nonlinear Fracture Test Analysis

NASA Technical Reports Server (NTRS)

Allen, Phillip A.; Wells, Douglas N.

2013-01-01

As fracture mechanics material testing evolves, the governing test standards continue to be refined to better reflect the latest understanding of the physics of the fracture processes involved. The traditional format of ASTM fracture testing standards, utilizing equations expressed directly in the text of the standard to assess the experimental result, is self-limiting in the complexity that can be reasonably captured. The use of automated analysis techniques to draw upon a rich, detailed solution database for assessing fracture mechanics tests provides a foundation for a new approach to testing standards that enables routine users to obtain highly reliable assessments of tests involving complex, non-linear fracture behavior. Herein, the case for automating the analysis of tests of surface cracks in tension in the elastic-plastic regime is utilized as an example of how such a database can be generated and implemented for use in the ASTM standards framework. The presented approach forms a bridge between the equation-based fracture testing standards of today and the next generation of standards solving complex problems through analysis automation.

Perfect sound insulation property of reclaimed waste tire rubber

NASA Astrophysics Data System (ADS)

Ubaidillah, Harjana, Yahya, Iwan; Kristiani, Restu; Muqowi, Eki; Mazlan, Saiful Amri

2016-03-01

This article reports an experimental investigation of sound insulation and absorption performance of a materials made of reclaimed ground tire rubber which is known as un-recyclable thermoset. The bulk waste tire is processed using single step recycling methods namely high-pressure high-temperature sintering (HPHTS). The bulk waste tire is simply placed into a mold and then a pressure load of 3 tons and a heating temperature of 200°C are applied to the mold. The HPHTS conducted for an hour and then it is cooled in room temperature. The resulted product is then evaluated the acoustical properties namely sound transmission loss (STL) and sound absorption coefficient using B&K Tube Kit Type 4206-T based on ISO 10534-2, ASTM E1050 and ASTM E2611. The sound absorption coefficient is found about 0.04 until 0.08 while STL value ranges between 50 to 60 dB. The sound absorption values are found to be very low (<0.1), while the average STL is higher than other elastomeric matrix found in previous work. The reclaimed tire rubber through HPHTS technique gives good soundproof characteristic.

Outgassing data for spacecraft materials

NASA Technical Reports Server (NTRS)

Campbell, W. A., Jr.; Marriott, R. S.; Park, J. J.

1980-01-01

A system for determining the mass loss in vacuum and for collecting the outgassed compounds was developed. Outgassing data, derived from tests at 398 K (125 degrees C) for 24 hours in vacuum as per ASTM E 59577, are compiled for numerous materials for spacecraft use. The data presented are the total mass loss (TML) and the collected volatile condensable materials (CVCM). The various materials are compiled by likely usage and alphabetically.

40 CFR Table 6 to Subpart Ddddd of... - Fuel Analysis Requirements

Code of Federal Regulations, 2014 CFR

2014-07-01

... D2013/D2013M a (for coal), ASTM D5198 a (for biomass), or EPA 3050 a (for solid fuel), or EPA 821-R-01... (for coal) or ASTM E711 a (for biomass), or ASTM D5864 a for liquids and other solids, or ASTM D240 a... D2234/D2234M a (for coal) or ASTM D6323 a (for coal or biomass), ASTM D4177 a (for liquid fuels) or ASTM...

40 CFR Table 6 to Subpart Ddddd of... - Fuel Analysis Requirements

Code of Federal Regulations, 2013 CFR

2013-07-01

... D2013/D2013M a (for coal), ASTM D5198 a (for biomass), or EPA 3050 a (for solid fuel), or EPA 821-R-01... (for coal) or ASTM E711 a (for biomass), or ASTM D5864 a for liquids and other solids, or ASTM D240 a... D2234/D2234M a (for coal) or ASTM D6323 a (for coal or biomass), ASTM D4177 a (for liquid fuels) or ASTM...

24 CFR 3280.604 - Materials.

Code of Federal Regulations, 2014 CFR

2014-04-01

.... Material and Property Standard for Special Cast Iron Fittings—IAPMO PS 5-84. Welding and Seamless Wrought Steel Pipe—ANSI/ASME B36.10-1979. Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless—ASTM A53-93. Pipe Threads, General Purpose (Inch)—ANSI/ASME B1.20.1-1983...

46 CFR 56.60-2 - Limitations on materials.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Boiler and Pressure Vessel Code * ASTM specifications Source of allowable stress Notes Ferrous Materials...-5. 2 Allowable stresses shall be the same as those listed in UCS23 of section VIII of the ASME.... 4 Allowable stresses shall be the same as those listed in UCS23 of section VIII of the ASME Boiler...

46 CFR 56.60-2 - Limitations on materials.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Boiler and Pressure Vessel Code * ASTM specifications Source of allowable stress Notes Ferrous Materials...-5. 2 Allowable stresses shall be the same as those listed in UCS23 of section VIII of the ASME.... 4 Allowable stresses shall be the same as those listed in UCS23 of section VIII of the ASME Boiler...

Groundwater Protection through Prevention. A Curriculum for Agricultural Education in Secondary Schools.

ERIC Educational Resources Information Center

Iowa State Univ. of Science and Technology, Ames. Dept. of Agricultural Education.

Water is one of the natural resources vital to any agricultural system. This material was developed in support of the Iowa Agricultural Science, Technology and Marketing (ASTM) program, focusing on groundwater educational concepts related to the 1987 Iowa Groundwater Protection Act. This material was designed to assist teachers in providing…

Thermal performance characterization of residential wall systems using a calibrated hot box with airflow induced by differential pressures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, D.C.; Ober, D.G.; Goodrow, J.T.

1995-09-01

ASTM E 283 ad ASTM E 1424 in conjunction with ASTM C 976 were used to study the effect of airflow on thermal performance of the wall. A typical residential 2 {times} 4 stud wall was constructed and placed on top of a subfloor, making a 2.44 {times} 2.74 m (8 by 9 ft) test specimen. This base wall assembly was then covered with two types of XPS sheathing, various housewraps, a 15{number_sign} felt, and a polyethylene vapor retarder film in 40 different configurations and tested individually per ASTM E 283 and per ASTM C 976. For 24 of themore » 40 C 976 tests, a differential pressure was induced across the test wall as per and ASTM E 1424. Airflows ranged from undetectable airflow at 0 {center_dot} Pa {Delta}P to 1.63 L/s {center_dot} m{sup 2} for the base wall assembly alone. Difference in airflow resistance performance between the ASTM E 283 and ASTM E 1424 test methods were noted. Thermal testing results incorporating both ASTM C 976 and ASTM E 1424 for tests 1--28 produced apparent thermal conductances (C-values) in the range of 0.40 W/m{sup 2} {center_dot} K for a nondetectable airflow level to 1.81 W/m{sup 2} {center_dot} K for an airflow of 1.53 L/s {center_dot} m{sup 2} for the base wall assembly alone with a 20-Pa {Delta}P. The calculated C-value for this base wall assembly was 0.40 W/m{sup 2} {center_dot} K. Test results reveal that airflow rates as low as 0.2 L/s {center_dot} m{sup 2} could produce a 46% increase in apparent C-value. Similar thermal performance differences were revealed when thicker shiplap XPS sheathing was used. Tests were also conducted using an Air-Tight Drywall configuration showing the effect of wind washing on thermal performance. By sealing the gypsum drywall on the base wall assembly tested, the apparent C-value, when exposed to a 12.5 Pa wind pressure, was found to be equivalent to a base wall assembly configuration which allows 0.15 L/s {center_dot} m{sup 2} airflow to penetrate completely through.« less

Design of nanocoatings by in situ phosphatizing reagent catalyzed polysilsesquioxane for corrosion inhibition and adhesion promotion on metal alloys

NASA Astrophysics Data System (ADS)

Henderson, Kimberly B.

When a metal reacts with oxygen and water, a redox reaction happens, which will cause corrosion. Current surface pretreatment for inhibiting corrosion on metal alloys is a phosphate conversion bath. The phosphate conversion bath will generate a phosphate-chromate layer to adhere strongly to a metal substrate. However, it is toxic and unfriendly to the environment. Our group proposed an innovative coating that contains a phosphate component (ISPR-In-situ Phosphatizing Reagent) within a protective coating. The ISPR coating will form a bound phosphate layer on the metal surface acting as the corrosion barrier and enhancing adhesion into the metal surface; moreover, it is low in cost and non-toxic. Within this dissertation, there are four projects that investigate design of ISPR nanocoatings for the use of corrosion inhibition and adhesion promotion. Surface modification and adjusting concentrations of materials with the different formulations are explored. The first project focuses on the adhesion enhancement of a coating created by modifying the surface of an aluminum panel. Secondly, the next project will discuss and present the use of three rare earth element formulations as a replacement for phosphate conversion coatings on magnesium alloy, AZ61. The third project is the design of a nanocoating by using heat dissipating materials to fill in small vacant spaces in the ISPR network coating on various metal alloys. The last project, studies the strategic selection of incorporating metal components into ISPR network by the reduction potential values on several different alloys. Many methods of analysis are used; SEM, TEM, ASTM B117, ASTM D1308, ASTM D3359, EIS, and thickness probe. It was found that the addition of ISPR in the nanocoatings dramatically improves the vitality of metal alloys and these results will be presented during this dissertation.

Summary: Update to ASTM Guide E 1523 to Charge Control and Charge Referencing Techniques in X-ray Photoelectron Spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baer, Donald R.

2005-04-22

An updated version of the ASTM guide E1523 to the methods to charge control and charge referencing techniques in x-ray photoelectron spectroscopy has been released by ASTM. The guide is meant to acquaint x-ray photoelectron spectroscopy (XPS) users with the various charge control and charge referencing techniques that are and have been used in the acquisition and interpretation of XPS data from surfaces of insulating specimens. The current guide has been expanded to include new references as well as recommendations for reporting information on charge control and charge referencing. The previous version of the document had been published in 1997.

40 CFR 52.742 - Incorporation by reference.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Water-Reducible Paints by Direct Injection into a Gas Chromatograph, for § 52.741(a)(4)(i)(B)(3)(iii... Chromatograph, for § 52.741(a)(4)(i)(B)(3)(v). (6) ASTM D2697-86, Standard Test Method for Volume Nonvolatile... Liquids by Isoteniscope, for § 52.741(a)(3), (a)(8)(ii), (a)(9)(iii), and (a)(10)(iii). (11) ASTM D323-82...

Fourier Transform Infrared Absorption Spectroscopy for Quantitative Analysis of Gas Mixtures at Low Temperatures for Homeland Security Applications.

PubMed

Meier, D C; Benkstein, K D; Hurst, W S; Chu, P M

2017-05-01

Performance standard specifications for point chemical vapor detectors are established in ASTM E 2885-13 and ASTM E 2933-13. The performance evaluation of the detectors requires the accurate delivery of known concentrations of the chemical target to the system under test. Referee methods enable the analyte test concentration and associated uncertainties in the analyte test concentration to be validated by independent analysis, which is especially important for reactive analytes. This work extends the capability of a previously demonstrated method for using Fourier transform infrared (FT-IR) absorption spectroscopy for quantitatively evaluating the composition of vapor streams containing hazardous materials at Acute Exposure Guideline Levels (AEGL) to include test conditions colder than laboratory ambient temperatures. The described method covers the use of primary reference spectra to establish analyte concentrations, the generation of secondary reference spectra suitable for measuring analyte concentrations under specified testing environments, and the use of additional reference spectra and spectral profile strategies to mitigate the uncertainties due to impurities and water condensation within the low-temperature (7 °C, -5 °C) test cell. Important benefits of this approach include verification of the test analyte concentration with characterized uncertainties by in situ measurements co-located with the detector under test, near-real-time feedback, and broad applicability to toxic industrial chemicals.

Fourier Transform Infrared Absorption Spectroscopy for Quantitative Analysis of Gas Mixtures at Low Temperatures for Homeland Security Applications

PubMed Central

Meier, D.C.; Benkstein, K.D.; Hurst, W.S.; Chu, P.M.

2016-01-01

Performance standard specifications for point chemical vapor detectors are established in ASTM E 2885-13 and ASTM E 2933-13. The performance evaluation of the detectors requires the accurate delivery of known concentrations of the chemical target to the system under test. Referee methods enable the analyte test concentration and associated uncertainties in the analyte test concentration to be validated by independent analysis, which is especially important for reactive analytes. This work extends the capability of a previously demonstrated method for using Fourier transform infrared (FT-IR) absorption spectroscopy for quantitatively evaluating the composition of vapor streams containing hazardous materials at Acute Exposure Guideline Levels (AEGL) to include test conditions colder than laboratory ambient temperatures. The described method covers the use of primary reference spectra to establish analyte concentrations, the generation of secondary reference spectra suitable for measuring analyte concentrations under specified testing environments, and the use of additional reference spectra and spectral profile strategies to mitigate the uncertainties due to impurities and water condensation within the low-temperature (7 °C, −5 °C) test cell. Important benefits of this approach include verification of the test analyte concentration with characterized uncertainties by in situ measurements co-located with the detector under test, near-real-time feedback, and broad applicability to toxic industrial chemicals. PMID:28090126

40 CFR 86.513-2004 - Fuel and engine lubricant specifications.

Code of Federal Regulations, 2010 CFR

2010-07-01

... ASTM D 86-97 23.9—35.0 1 2. 10% point, °C ASTM D 86-97 48.9—57.2 3. 50% point, °C ASTM D 86-97 93.3—110.0 4. 90% point, °C ASTM D 86-97 148.9—162.8 5. End point, °C ASTM D 86-97 212.8 Hydrocarbon composition: 1. Olefins, volume % ASTM D 1319-98 10 maximum 2. Aromatics, volume % ASTM D 1319-98 35 maximum 3...

40 CFR 1036.805 - Symbols, acronyms, and abbreviations.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... ASTM American Society for Testing and Materials. BTU British thermal units. CFR Code of Federal... pound. lbC pound carbon. LPG liquefied petroleum gas. Mg megagrams (10 6 grams, or one metric ton). MJ...

40 CFR 1036.805 - Symbols, acronyms, and abbreviations.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... ASTM American Society for Testing and Materials. BTU British thermal units. CFR Code of Federal... pound. lbC pound carbon. LPG liquefied petroleum gas. Mg megagrams (10 6 grams, or one metric ton). MJ...

40 CFR 1036.805 - Symbols, acronyms, and abbreviations.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... ASTM American Society for Testing and Materials. BTU British thermal units. CFR Code of Federal... pound. lbC pound carbon. LPG liquefied petroleum gas. Mg megagrams (10 6 grams, or one metric ton). MJ...

40 CFR 721.4250 - Hexanoic acid, 2-ethyl-, ethenyl ester.

Code of Federal Regulations, 2010 CFR

2010-07-01

... accordance with the most current version of the American Society for Testing and Materials (ASTM) F739... control technology does not apply. Instead, if the waste stream containing the substance will be treated...

40 CFR 721.4250 - Hexanoic acid, 2-ethyl-, ethenyl ester.

Code of Federal Regulations, 2011 CFR

2011-07-01

... accordance with the most current version of the American Society for Testing and Materials (ASTM) F739... control technology does not apply. Instead, if the waste stream containing the substance will be treated...

Class-conditional feature modeling for ignitable liquid classification with substantial substrate contribution in fire debris analysis.

PubMed

Lopatka, Martin; Sigman, Michael E; Sjerps, Marjan J; Williams, Mary R; Vivó-Truyols, Gabriel

2015-07-01

Forensic chemical analysis of fire debris addresses the question of whether ignitable liquid residue is present in a sample and, if so, what type. Evidence evaluation regarding this question is complicated by interference from pyrolysis products of the substrate materials present in a fire. A method is developed to derive a set of class-conditional features for the evaluation of such complex samples. The use of a forensic reference collection allows characterization of the variation in complex mixtures of substrate materials and ignitable liquids even when the dominant feature is not specific to an ignitable liquid. Making use of a novel method for data imputation under complex mixing conditions, a distribution is modeled for the variation between pairs of samples containing similar ignitable liquid residues. Examining the covariance of variables within the different classes allows different weights to be placed on features more important in discerning the presence of a particular ignitable liquid residue. Performance of the method is evaluated using a database of total ion spectrum (TIS) measurements of ignitable liquid and fire debris samples. These measurements include 119 nominal masses measured by GC-MS and averaged across a chromatographic profile. Ignitable liquids are labeled using the American Society for Testing and Materials (ASTM) E1618 standard class definitions. Statistical analysis is performed in the class-conditional feature space wherein new forensic traces are represented based on their likeness to known samples contained in a forensic reference collection. The demonstrated method uses forensic reference data as the basis of probabilistic statements concerning the likelihood of the obtained analytical results given the presence of ignitable liquid residue of each of the ASTM classes (including a substrate only class). When prior probabilities of these classes can be assumed, these likelihoods can be connected to class probabilities. In order to compare the performance of this method to previous work, a uniform prior was assumed, resulting in an 81% accuracy for an independent test of 129 real burn samples. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

High Temperature, Slow Strain Rate Forging of Advanced Disk Alloy ME3

NASA Technical Reports Server (NTRS)

Gabb, Timothy P.; OConnor, Kenneth

2001-01-01

The advanced disk alloy ME3 was designed in the HSR/EPM disk program to have extended durability at 1150 to 1250 F in large disks. This was achieved by designing a disk alloy and process producing balanced monotonic, cyclic, and time-dependent mechanical properties. combined with robust processing and manufacturing characteristics. The resulting baseline alloy, processing, and supersolvus heat treatment produces a uniform, relatively fine mean grain size of about ASTM 7, with as-large-as (ALA) grain size of about ASTM 3. There is a long term need for disks with higher rim temperature capabilities than 1250 F. This would allow higher compressor exit (T3) temperatures and allow the full utilization of advanced combustor and airfoil concepts under development. Several approaches are being studied that modify the processing and chemistry of ME3, to possibly improve high temperature properties. Promising approaches would be applied to subscale material, for screening the resulting mechanical properties at these high temperatures. n obvious path traditionally employed to improve the high temperature and time-dependent capabilities of disk alloys is to coarsen the grain size. A coarser grain size than ASTM 7 could potentially be achieved by varying the forging conditions and supersolvus heat treatment. The objective of this study was to perform forging and heat treatment experiments ("thermomechanical processing experiments") on small compression test specimens of the baseline ME3 composition, to identify a viable forging process allowing significantly coarser grain size targeted at ASTM 3-5, than that of the baseline, ASTM 7.

Three-Body Abrasion Testing Using Lunar Dust Simulants to Evaluate Surface System Materials

NASA Technical Reports Server (NTRS)

Kobrick, Ryan L.; Budinski, Kenneth G.; Street, Kenneth W., Jr.; Klaus, David M.

2010-01-01

Numerous unexpected operational issues relating to the abrasive nature of lunar dust, such as scratched visors and spacesuit pressure seal leaks, were encountered during the Apollo missions. To avoid reoccurrence of these unexpected detrimental equipment problems on future missions to the Moon, a series of two- and three-body abrasion tests were developed and conducted in order to begin rigorously characterizing the effect of lunar dust abrasiveness on candidate surface system materials. Two-body scratch tests were initially performed to examine fundamental interactions of a single particle on a flat surface. These simple and robust tests were used to establish standardized measurement techniques for quantifying controlled volumetric wear. Subsequent efforts described in the paper involved three-body abrasion testing designed to be more representative of actual lunar interactions. For these tests, a new tribotester was developed to expose samples to a variety of industrial abrasives and lunar simulants. The work discussed in this paper describes the three-body hardware setup consisting of a rotating rubber wheel that applies a load on a specimen as a loose abrasive is fed into the system. The test methodology is based on ASTM International (ASTM) B611, except it does not mix water with the abrasive. All tests were run under identical conditions. Abraded material specimens included poly(methyl methacrylate) (PMMA), hardened 1045 steel, 6061-T6 aluminum (Al) and 1018 steel. Abrasives included lunar mare simulant JSC- 1A-F (nominal size distribution), sieved JSC-1A-F (<25 m particle diameter), lunar highland simulant NU-LHT-2M, alumina (average diameter of 50 m used per ASTM G76), and silica (50/70 mesh used per ASTM G65). The measured mass loss from each specimen was converted using standard densities to determine total wear volume in cm3. Abrasion was dominated by the alumina and the simulants were only similar to the silica (i.e., sand) on the softer materials of aluminum and PMMA. The nominal JSC- 1A-F consistently showed more abrasion wear than the sieved version of the simulant. The lunar dust displayed abrasivity to all of the test materials, which are likely to be used in lunar landing equipment. Based on this test experience and pilot results obtained, recommendations are made for systematic abrasion testing of candidate materials intended for use in lunar exploration systems and in other environments with similar dust challenges.

Mechanical characterization of Al-2024 reinforced with fly ash and E-glass by stir casting method

NASA Astrophysics Data System (ADS)

Ramesh, B. T.; Swamy, R. P.; Vinayak, Koppad

2018-04-01

The properties of MMCs enhance their handling in automotive and various applications for the reason that of encouraging properties of high stiffness and high strength, low density, high electrical and thermal conductivity, corrosion resistance, improved wear resistance etc. Metal Matrix Composites are a vital family of materials designed at achieving an improved combination of properties. Our paper deals through to fabricate Hybrid Composite by heating Al 2024 in furnace at a temperature of around 4000 C. E-Glass fiber & Fly ash will be added to the molten metal with changing weight fractions and stirred strongly. Then the ensuing composition will poured into the mould to obtain hybrid composite casting. Aluminium alloy (2024) is the matrix metal used in the present investigation. Fly ash and e-glass are used as the reinforced materials to produce the composite by stir casting. Fly ash is selected because of it is less expensive and low density reinforcement available in great quantities as solid disposal from thermal power plants. The Test specimen is prepared as per ASTM standards size by machining operations to conduct Tensile, Compression, Hardness, and wear test. The test specimens are furnished for tensile, compression strength and wear as per ASTM standard E8, E9 and G99 respectively using Universal Testing Machine and pin on disk machine. It is seen that the fabricated MMC obtained has got enhanced mechanical strength.

49 CFR 192.113 - Longitudinal joint factor (E) for steel pipe.

Code of Federal Regulations, 2010 CFR

2010-10-01

... class Longitudinal joint factor (E) ASTM A 53/A53M Seamless 1.00 Electric resistance welded 1.00 Furnace butt welded .60 ASTM A 106 Seamless 1.00 ASTM A 333/A 333M Seamless 1.00 Electric resistance welded 1.00 ASTM A 381 Double submerged arc welded 1.00 ASTM A 671 Electric-fusion-welded 1.00 ASTM A 672...

Laminated thermoplastic composite material from recycled high density polyethylene

NASA Technical Reports Server (NTRS)

Liu, Ping; Waskom, Tommy L.

1994-01-01

The design of a materials-science, educational experiment is presented. The student should understand the fundamentals of polymer processing and mechanical property testing of materials. The ability to use American Society for Testing and Materials (ASTM) standards is also necessary for designing material test specimens and testing procedures. The objectives of the experiment are (1) to understand the concept of laminated composite materials, processing, testing, and quality assurance of thermoplastic composites and (2) to observe an application example of recycled plastics.

A standardized evaluation of artefacts from metallic compounds during fast MR imaging

PubMed Central

Murakami, Shumei; Kataoka, Miyoshi; Kakimoto, Naoya; Shimamoto, Hiroaki; Kreiborg, Sven

2016-01-01

Objectives: Metallic compounds present in the oral and maxillofacial regions (OMRs) cause large artefacts during MR scanning. We quantitatively assessed these artefacts embedded within a phantom according to standards set by the American Society for Testing and Materials (ASTM). Methods: Seven metallic dental materials (each of which was a 10-mm3 cube embedded within a phantom) were scanned [i.e. aluminium (Al), silver alloy (Ag), type IV gold alloy (Au), gold–palladium–silver alloy (Au-Pd-Ag), titanium (Ti), nickel–chromium alloy (NC) and cobalt–chromium alloy (CC)] and compared with a reference image. Sequences included gradient echo (GRE), fast spin echo (FSE), gradient recalled acquisition in steady state (GRASS), a spoiled GRASS (SPGR), a fast SPGR (FSPGR), fast imaging employing steady state (FIESTA) and echo planar imaging (EPI; axial/sagittal planes). Artefact areas were determined according to the ASTM-F2119 standard, and artefact volumes were assessed using OsiriX MD software (Pixmeo, Geneva, Switzerland). Results: Tukey–Kramer post hoc tests were used for statistical comparisons. For most materials, scanning sequences eliciting artefact volumes in the following (ascending) order FSE-T1/FSE-T2 < FSPGR/SPGR < GRASS/GRE < FIESTA < EPI. For all scanning sequences, artefact volumes containing Au, Al, Ag and Au-Pd-Ag were significantly smaller than other materials (in which artefact volume size increased, respectively, from Ti < NC < CC). The artefact-specific shape (elicited by the cubic sample) depended on the scanning plane (i.e. a circular pattern for the axial plane and a “clover-like” pattern for the sagittal plane). Conclusions: The availability of standardized information on artefact size and configuration during MRI will enhance diagnosis when faced with metallic compounds in the OMR. PMID:27459058

Certification of alternative aviation fuels and blend components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson III, George R.; Edwards, Tim; Corporan, Edwin

2013-01-15

Aviation turbine engine fuel specifications are governed by ASTM International, formerly known as the American Society for Testing and Materials (ASTM) International, and the British Ministry of Defence (MOD). ASTM D1655 Standard Specification for Aviation Turbine Fuels and MOD Defence Standard 91-91 are the guiding specifications for this fuel throughout most of the world. Both of these documents rely heavily on the vast amount of experience in production and use of turbine engine fuels from conventional sources, such as crude oil, natural gas condensates, heavy oil, shale oil, and oil sands. Turbine engine fuel derived from these resources and meetingmore » the above specifications has properties that are generally considered acceptable for fuels to be used in turbine engines. Alternative and synthetic fuel components are approved for use to blend with conventional turbine engine fuels after considerable testing. ASTM has established a specification for fuels containing synthesized hydrocarbons under D7566, and the MOD has included additional requirements for fuels containing synthetic components under Annex D of DS91-91. New turbine engine fuel additives and blend components need to be evaluated using ASTM D4054, Standard Practice for Qualification and Approval of New Aviation Turbine Fuels and Fuel Additives. This paper discusses these specifications and testing requirements in light of recent literature claiming that some biomass-derived blend components, which have been used to blend in conventional aviation fuel, meet the requirements for aviation turbine fuels as specified by ASTM and the MOD. The 'Table 1' requirements listed in both D1655 and DS91-91 are predicated on the assumption that the feedstocks used to make fuels meeting these requirements are from approved sources. Recent papers have implied that commercial jet fuel can be blended with renewable components that are not hydrocarbons (such as fatty acid methyl esters). These are not allowed blend components for turbine engine fuels as discussed in this paper.« less

40 CFR 799.5085 - Chemical testing requirements for first group of high production volume chemicals (HPV1).

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Acute Toxicity to Daphnia: ASTM E 729 3. Toxicity to Plants (Algae): ASTM E 1218 Test Group 2 for C1: 1. Chronic Toxicity to Daphnia: ASTM E 1193 2. Toxicity to Plants (Algae): ASTM E 1218 The following are the... conditions. Test Group 1 for C2: 1. Acute Toxicity to Daphnia: ASTM E 729 2. Toxicity to Plants (Algae): ASTM...

40 CFR 799.5085 - Chemical testing requirements for first group of high production volume chemicals (HPV1).

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Acute Toxicity to Daphnia: ASTM E 729 3. Toxicity to Plants (Algae): ASTM E 1218 Test Group 2 for C1: 1. Chronic Toxicity to Daphnia: ASTM E 1193 2. Toxicity to Plants (Algae): ASTM E 1218 The following are the... conditions. Test Group 1 for C2: 1. Acute Toxicity to Daphnia: ASTM E 729 2. Toxicity to Plants (Algae): ASTM...

Nuclear Gauge Calibration and Testing Guidelines for Hawaii

DOT National Transportation Integrated Search

2006-12-15

Project proposal brief: AASHTO and ASTM nuclear gauge testing procedures can lead to misleading density and moisture readings for certain Hawaiian soils. Calibration curves need to be established for these unique materials, along with clear standard ...

COAL SULFUR MEASUREMENTS

EPA Science Inventory

The report describes a new technique for sulfur forms analysis based on low-temperature oxygen plasma ashing. The technique involves analyzing the low-temperature plasma ash by modified ASTM techniques after selectively removing the organic material. The procedure has been tested...

16 CFR § 1215.2 - Requirements for infant bath seats.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959 USA, phone: 610-832-9585; http://www.astm... Archives and Records Administration (NARA). For information on the availability of this material at NARA...

16 CFR 1224.2 - Requirements for portable bed rails.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959 USA, phone: 610-832-9585; http://www.astm... Archives and Records Administration (NARA). For information on the availability of this material at NARA...

An Evaluation of a Proposed Revision of the ASTM D 1990 Grouping Procedure

Treesearch

Steve P Verrill; James W. Evans; David E. Kretschmann; Cherilyn A. Hatfield

2013-01-01

Lum, Taylor, and Zidek have proposed a revised procedure for wood species grouping in ASTM standard D 1990. We applaud the authors’ recognition of the importance of considering a strength distribution’s variability as well as its fifth percentile. However, we have concerns about their proposed method of incorporating this information into a standard. We detail these...

Comparative study between EDXRF and ASTM E572 methods using two-way ANOVA

NASA Astrophysics Data System (ADS)

Krummenauer, A.; Veit, H. M.; Zoppas-Ferreira, J.

2018-03-01

Comparison with reference method is one of the necessary requirements for the validation of non-standard methods. This comparison was made using the experiment planning technique with two-way ANOVA. In ANOVA, the results obtained using the EDXRF method, to be validated, were compared with the results obtained using the ASTM E572-13 standard test method. Fisher's tests (F-test) were used to comparative study between of the elements: molybdenum, niobium, copper, nickel, manganese, chromium and vanadium. All F-tests of the elements indicate that the null hypothesis (Ho) has not been rejected. As a result, there is no significant difference between the methods compared. Therefore, according to this study, it is concluded that the EDXRF method was approved in this method comparison requirement.

40 CFR 63.5758 - How do I determine the organic HAP content of materials?

Code of Federal Regulations, 2010 CFR

2010-07-01

... for each material used in your open molding resin and gel coat operations, carpet and fabric adhesive... ASTM) to measure the mass fraction of volatile matter of resins and gel coats for open molding... section, such as manufacturer's formulation data, according to paragraphs (a)(5)(i) through (iii) of this...

46 CFR 56.60-15 - Ductile iron.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Ductile iron. 56.60-15 Section 56.60-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Materials § 56.60-15 Ductile iron. (a) Ductile cast iron components made of material conforming to ASTM A 395 (incorporated by reference, see 46 CF...

46 CFR 56.60-15 - Ductile iron.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Ductile iron. 56.60-15 Section 56.60-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Materials § 56.60-15 Ductile iron. (a) Ductile cast iron components made of material conforming to ASTM A 395 (incorporated by reference, see 46 CF...

46 CFR 56.60-15 - Ductile iron.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Ductile iron. 56.60-15 Section 56.60-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Materials § 56.60-15 Ductile iron. (a) Ductile cast iron components made of material conforming to ASTM A 395 (incorporated by reference, see 46 CF...

46 CFR 56.60-15 - Ductile iron.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Ductile iron. 56.60-15 Section 56.60-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Materials § 56.60-15 Ductile iron. (a) Ductile cast iron components made of material conforming to ASTM A 395 (incorporated by reference, see 46 CF...

46 CFR 56.60-15 - Ductile iron.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Ductile iron. 56.60-15 Section 56.60-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Materials § 56.60-15 Ductile iron. (a) Ductile cast iron components made of material conforming to ASTM A 395 (incorporated by reference, see 46 CF...

40 CFR 799.5087 - Chemical testing requirements for second group of high production volume chemicals (HPV2).

Code of Federal Regulations, 2011 CFR

2011-07-01

...: ASTM E 729-96 (Reapproved 2007) 3. Toxicity to Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C1: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97 (Reapproved 2004) 2. Toxicity to Plants (Algae): ASTM E 1218... Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C2: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97...

40 CFR 799.5087 - Chemical testing requirements for second group of high production volume chemicals (HPV2).

Code of Federal Regulations, 2013 CFR

2013-07-01

...: ASTM E 729-96 (Reapproved 2007) 3. Toxicity to Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C1: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97 (Reapproved 2004) 2. Toxicity to Plants (Algae): ASTM E 1218... Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C2: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97...

40 CFR 799.5087 - Chemical testing requirements for second group of high production volume chemicals (HPV2).

Code of Federal Regulations, 2012 CFR

2012-07-01

...: ASTM E 729-96 (Reapproved 2007) 3. Toxicity to Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C1: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97 (Reapproved 2004) 2. Toxicity to Plants (Algae): ASTM E 1218... Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C2: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97...

40 CFR 799.5087 - Chemical testing requirements for second group of high production volume chemicals (HPV2).

Code of Federal Regulations, 2014 CFR

2014-07-01

...: ASTM E 729-96 (Reapproved 2007) 3. Toxicity to Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C1: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97 (Reapproved 2004) 2. Toxicity to Plants (Algae): ASTM E 1218... Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C2: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97...

Evaluation of manual resuscitators used in ICUs in Brazil*

PubMed Central

Ortiz, Tatiana de Arruda; Forti, Germano; Volpe, Márcia Souza; Beraldo, Marcelo do Amaral; Amato, Marcelo Britto Passos; Carvalho, Carlos Roberto Ribeiro; Tucci, Mauro Roberto

2013-01-01

OBJECTIVE: To evaluate the performance of manual resuscitators (MRs) used in Brazil in accordance with international standards. METHODS: Using a respiratory system simulator, four volunteer physiotherapists employed eight MRs (five produced in Brazil and three produced abroad), which were tested for inspiratory and expiratory resistance of the patient valve; functioning of the pressure-limiting valve; and tidal volume (VT) generated when the one-handed and two-handed techniques were used. The tests were performed and analyzed in accordance with the American Society for Testing and Materials (ASTM) F920-93 criteria. RESULTS: Expiratory resistance was greater than 6 cmH2O . L−1 . s−1 in only one MR. The pressure-limiting valve, a feature of five of the MRs, opened at low pressures (< 17 cmH2O), and the maximal pressure was 32.0-55.9 cmH2O. Mean VT varied greatly among the MRs tested. The mean VT values generated with the one-handed technique were lower than the 600 mL recommended by the ASTM. In the situations studied, mean VT was generally lower from the Brazilian-made MRs that had a pressure-limiting valve. CONCLUSIONS: The resistances imposed by the patient valve met the ASTM criteria in all but one of the MRs tested. The pressure-limiting valves of the Brazilian-made MRs usually opened at low pressures, providing lower VT values in the situations studied, especially when the one-handed technique was used, suggesting that both hands should be used and that the pressure-limiting valve should be closed whenever possible. PMID:24310633

Impact of using scatter-mimicking beams instead of standard beams to measure penetration when assessing the protective value of radiation-protective garments.

PubMed

Jones, A Kyle; Pasciak, Alexander S; Wagner, Louis K

2018-03-01

Use standardized methods to determine how assessment of protective value of radiation-protective garments changes under conditions employing standard beam qualities, scatter-mimicking primary beams, and a modified H p (10) measurement. The shielding properties of radiation-protective garments depend on the spectrum of beam energies striking the garment and the attenuation properties of materials used to construct the garment, including x-ray fluorescence produced by these materials. In this study the primary beam spectra employed during clinical interventional radiology and cardiology procedures (clinical primary beams, CPB) were identified using radiation dose structured reports (RDSR) and fluoroscope log data. Monte Carlo simulation was used to determine the scattered radiation spectra produced by these CPB during typical clinical application. For these scattered spectra, scatter-mimicking primary beams (SMPB) were determined using numerical optimization-based spectral reconstruction that adjusted kV and filtration to produce the SMPB that optimally matched the scattered spectrum for each CPB. The penetration of a subset of SMPB through four radiation-protective garments of varying compositions and nominal thicknesses was measured using a geometry specified by the International Electrotechnical Commission (IEC). The diagnostic radiological index of protection (DRIP), which increases with increasing penetration through a garment, was calculated using these measurements. Penetration through the same garments was measured for standard beams specified by the American Society of Testing and Materials (ASTM). Finally, 10 mm of PMMA was affixed to the inside of each garment and the DRIP remeasured in this configuration to simulate H p (10). The SMPB based on actual CPB were in general characterized by lower kV (range 60-76) and higher half-value layer (HVL, range 3.44-4.89 mm Al) than standard beam qualities specified by ASTM (kV range 70-85; HVL range 3.4-4.0 mm Al). A lead garment of nominal thickness 0.5 mm (D) had a DRIP of 0.8%, two lead-free garments of 0.5 mm nominal thickness had DRIPs of 1.2% (A) and 2.2% (B), and a lead-free bilayer (C) had a DRIP of 1.4%. When standard beam qualities specified by the ASTM were used, the DRIP for D was 2.2%, 175% higher than the DRIP measured using SMPB, and for A, B, and C was 2.8%, 3.2%, and 2.9%, respectively. This was 133%, 45%, and 107% higher than the DRIP measured using SMPB. Differences between the DRIP of lead-alternative garments and the lead garment were reduced when measured with 10 mm of PMMA. Using this method, the measured DRIPs were 2.2% (A), 3.1% (B), 2.5% (C), and 2.3% (D). Penetration of radiation through radiation-protective garments depended strongly on the methods and X-ray spectra used for evaluation. The DRIP was higher (i.e., protective value was lower) for lead-alternative garments than for lead garments in this evaluation. The DRIP was lower for all garments when SMPB based on actual clinical beam quality data were used to measure penetration compared to ASTM standard beams. Differences in penetration between lead-alternative and lead garments were less when the DRIP was measured with 10 mm of PMMA between the garment and the chamber. © 2018 American Association of Physicists in Medicine.

Preparation and characterization of functionalized single walled carbon nanotubes (fSWCNT)/ Hydroxyapatite (HAp)-Nylon hybridized composite biomaterial to study the mechanical properties

NASA Astrophysics Data System (ADS)

Khanal, Suraj; Leventouri, Theodora; Mahfuz, Hassan; Rondinone, Adam

2014-03-01

Synthetic hydroxyapatite (HAp) bears poor mechanical properties that limit its applicability in orthopedics. We study the possibility of overcoming such limitations by incorporating functionalized single walled carbon nanotubes (fSWCNT) in a biocompatible/bioactive nano-composite. We present results from synthesis and characterization of samples prepared under different processing parameters. Ultra sonication method was to disperse functionalized single walled carbon nanotubes (fSWCNT) in HAp followed by a simple hot assorting method to incorporate with polymerized ɛ-caprolactam. The fracture toughness of the composite materials was tested in compliance with the ASTM D-5045 standard. We have found that while the fracture toughness strongly depends on the processing parameters, a value comparable to the one for cortical bone is achieved. Mechanical properties, electron microscopy and crystal structure properties of the composite materials will be discussed.

75 FR 30440 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM International

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-01

... Production Act of 1993--ASTM International Notice is hereby given that, on May 6, 2010, pursuant to Section 6... Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with the Attorney... recovery of antitrust plaintiffs to actual damages under specified circumstances. Specifically, ASTM has...

Sequestration Coating Performance Requirements for ...

EPA Pesticide Factsheets

symposium paper The EPA’s National Homeland Security Research Center (NHSRC), in collaboration with ASTM International, developed performance standards for materials which could be applied to exterior surfaces contaminated by an RDD to mitigate the spread and migration of radioactive contamination.

Harmonization of texture and skid-resistance measurements.

DOT National Transportation Integrated Search

2008-09-30

Due to safety concerns associated with friction testing on both high and low-speed facilities, testing at variable speeds has been previously investigated by the Florida DOT. The American Society for Testing and materials (ASTM) has endorsed this con...

Development of apparent viscosity test for hot-poured crack sealants.

DOT National Transportation Integrated Search

2008-11-01

Current crack sealant specifications focuses on utilizing simple empirical tests such as penetration, : resilience, flow, and bonding to cement concrete briquettes (ASTM D3405) to measure the ability of the material : to resist cohesive and adhesion ...

30 CFR 254.26 - What information must I include in the “Worst case discharge scenario” appendix?

Code of Federal Regulations, 2011 CFR

2011-07-01

... limits of current technology, for the range of environmental conditions anticipated at your facility; and... Society for Testing of Materials (ASTM) publication F625-94, Standard Practice for Describing...

24 CFR 200.942 - Supplementary specific procedural requirements under HUD building product standards and...

Code of Federal Regulations, 2010 CFR

2010-04-01

... the following standards: (i) AATCC 20A-81—Fiber Analysis: Quantitative; (ii) AATCC 16E-82... 12215, Research Triangle Park, NC 27709; (ii) American Society for Testing and Materials (ASTM), 1916...

24 CFR 200.942 - Supplementary specific procedural requirements under HUD building product standards and...

Code of Federal Regulations, 2014 CFR

2014-04-01

... the following standards: (i) AATCC 20A-81—Fiber Analysis: Quantitative; (ii) AATCC 16E-82... 12215, Research Triangle Park, NC 27709; (ii) American Society for Testing and Materials (ASTM), 1916...

24 CFR 200.942 - Supplementary specific procedural requirements under HUD building product standards and...

Code of Federal Regulations, 2011 CFR

2011-04-01

... the following standards: (i) AATCC 20A-81—Fiber Analysis: Quantitative; (ii) AATCC 16E-82... 12215, Research Triangle Park, NC 27709; (ii) American Society for Testing and Materials (ASTM), 1916...

24 CFR 200.942 - Supplementary specific procedural requirements under HUD building product standards and...

Code of Federal Regulations, 2013 CFR

2013-04-01

... the following standards: (i) AATCC 20A-81—Fiber Analysis: Quantitative; (ii) AATCC 16E-82... 12215, Research Triangle Park, NC 27709; (ii) American Society for Testing and Materials (ASTM), 1916...

24 CFR 200.942 - Supplementary specific procedural requirements under HUD building product standards and...

Code of Federal Regulations, 2012 CFR

2012-04-01

... the following standards: (i) AATCC 20A-81—Fiber Analysis: Quantitative; (ii) AATCC 16E-82... 12215, Research Triangle Park, NC 27709; (ii) American Society for Testing and Materials (ASTM), 1916...

Combined target factor analysis and Bayesian soft-classification of interference-contaminated samples: forensic fire debris analysis.

PubMed

Williams, Mary R; Sigman, Michael E; Lewis, Jennifer; Pitan, Kelly McHugh

2012-10-10

A bayesian soft classification method combined with target factor analysis (TFA) is described and tested for the analysis of fire debris data. The method relies on analysis of the average mass spectrum across the chromatographic profile (i.e., the total ion spectrum, TIS) from multiple samples taken from a single fire scene. A library of TIS from reference ignitable liquids with assigned ASTM classification is used as the target factors in TFA. The class-conditional distributions of correlations between the target and predicted factors for each ASTM class are represented by kernel functions and analyzed by bayesian decision theory. The soft classification approach assists in assessing the probability that ignitable liquid residue from a specific ASTM E1618 class, is present in a set of samples from a single fire scene, even in the presence of unspecified background contributions from pyrolysis products. The method is demonstrated with sample data sets and then tested on laboratory-scale burn data and large-scale field test burns. The overall performance achieved in laboratory and field test of the method is approximately 80% correct classification of fire debris samples. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Development and Sliding Wear Response of Epoxy Composites Filled with Coal Mine Overburden Material

NASA Astrophysics Data System (ADS)

Das, Prithika; Satapathy, Alok; Mishra, M. K.

2018-03-01

The paper reports on development and characterization of epoxy based composites filled with micro-sized mine overburden material. Coal mine overburden material is typically highly heterogeneous and is considered as waste material. For excavating each ton of coal, roughly 5 tons of overburden materials are removed and is dumped nearby occupying large space. Gainful utilization of this waste is a major challenge. In the present work, this material is used as filler materials in making a new class of epoxy matrix composites. Composites with different weight proportions of fillers (0, 10, 20, 30 and 40) wt. % are prepared by hand layup technique. Compression tests are performed as per corresponding ASTM standards to assess the compressive strength of these composites. Further, dry sliding tests are performed following ASTM G99 standards using a pin on disk machine. A design of experiment approach based on Taguchi’s L16 orthogonal arrays is adopted. Tests are performed at different sliding velocities for multiple sliding distances under varying normal loads. Specific wear rates of the composites under different test conditions are obtained. The analysis of the test results revealed that the filler content and the sliding velocity are the most predominant control factors affecting the wear rate. This work thus, opens up a new avenue for the value added utilization of coal mine overburden material.

Standard methods for filled hole tension testing of textile composites

NASA Technical Reports Server (NTRS)

Portanova, M. A.; Masters, J. E.

1995-01-01

The effects of two test specimen geometry parameters, the specimen width and W/D ratio, on filled-hole tensile strength were determined for textile composite materials. Test data generated by Boeing and Lockheed on 2-D and 3-D braids, and 3-D weaves were used to make these evaluations. The investigation indicated that filled-hole tensile-strength showed little sensitivity to either parameter. Test specimen configurations used in open-hole tension tests, such as those suggested by ASTM D5766 - Standard Test Method for Open Hole Tensile Strength of Polymer Matrix Composite Laminates or those proposed by MIL-HDBK-17-lD should provide adequate results for material comparisons studies. Comparisons of the materials' open-hole and filled-hole tensile strengths indicated that the latter were generally lower than the former. The 3-D braids were the exception; their filled-hole strengths were unexpected larger than their open-hole strengths. However, these increases were small compared to the scatter in the data. Thus, filled hole tension may be a critical design consideration for textile composite materials.

Measurement of susceptibility artifacts with histogram-based reference value on magnetic resonance images according to standard ASTM F2119.

PubMed

Heinrich, Andreas; Teichgräber, Ulf K; Güttler, Felix V

2015-12-01

The standard ASTM F2119 describes a test method for measuring the size of a susceptibility artifact based on the example of a passive implant. A pixel in an image is considered to be a part of an image artifact if the intensity is changed by at least 30% in the presence of a test object, compared to a reference image in which the test object is absent (reference value). The aim of this paper is to simplify and accelerate the test method using a histogram-based reference value. Four test objects were scanned parallel and perpendicular to the main magnetic field, and the largest susceptibility artifacts were measured using two methods of reference value determination (reference image-based and histogram-based reference value). The results between both methods were compared using the Mann-Whitney U-test. The difference between both reference values was 42.35 ± 23.66. The difference of artifact size was 0.64 ± 0.69 mm. The artifact sizes of both methods did not show significant differences; the p-value of the Mann-Whitney U-test was between 0.710 and 0.521. A standard-conform method for a rapid, objective, and reproducible evaluation of susceptibility artifacts could be implemented. The result of the histogram-based method does not significantly differ from the ASTM-conform method.

White Paper Summary of 2nd ASTM International Workshop on Hydrides in Zirconium Alloy Cladding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sindelar, R.; Louthan, M.; PNNL, B.

2015-05-29

This white paper recommends that ASTM International develop standards to address the potential impact of hydrides on the long term performance of irradiated zirconium alloys. The need for such standards was apparent during the 2nd ASTM International Workshop on Hydrides in Zirconium Alloy Cladding and Assembly Components, sponsored by ASTM International Committee C26.13 and held on June 10-12, 2014, in Jackson, Wyoming. The potentially adverse impacts of hydrogen and hydrides on the long term performance of irradiated zirconium-alloy cladding on used fuel were shown to depend on multiple factors such as alloy chemistry and processing, irradiation and post irradiation history,more » residual and applied stresses and stress states, and the service environment. These factors determine the hydrogen content and hydride morphology in the alloy, which, in turn, influence the response of the alloy to the thermo-mechanical conditions imposed (and anticipated) during storage, transport and disposal of used nuclear fuel. Workshop presentations and discussions showed that although hydrogen/hydride induced degradation of zirconium alloys may be of concern, the potential for occurrence and the extent of anticipated degradation vary throughout the nuclear industry because of the variations in hydrogen content, hydride morphology, alloy chemistry and irradiation conditions. The tools and techniques used to characterize hydrides and hydride morphologies and their impacts on material performance also vary. Such variations make site-to-site comparisons of test results and observations difficult. There is no consensus that a single material or system characteristic (e.g., reactor type, burnup, hydrogen content, end-of life stress, alloy type, drying temperature, etc.) is an effective predictor of material response during long term storage or of performance after long term storage. Multi-variable correlations made for one alloy may not represent the behavior of another alloy exposed to identical conditions and the material responses to thermo-mechanical exposures will be different depending on the materials and systems used. The discussions at the workshop showed several gaps in the standardization of processes and techniques necessary to assess the long term performance of irradiated zirconium alloy cladding during dry storage and transport. The development of, and adherence to, standards to help bridge these gaps will strengthen the technical basis for long term storage and post-storage operations, provide consistency across the nuclear industry, maximize the value of most observations, and enhance the understanding of behavioral differences among alloys. The need for, and potential benefits of, developing the recommended standards are illustrated in the various sections of this report.« less

49 CFR 179.400-5 - Materials.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400-5 Materials. (a) Stainless steel of ASTM A 240/A 240M (IBR, see § 171.7 of this subchapter), Type 304 or 304L must be used... the lading. (b) Any steel casting, steel forging, steel structural shape or carbon steel plate used to...

49 CFR 179.400-5 - Materials.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400-5 Materials. (a) Stainless steel of ASTM A 240/A 240M (IBR, see § 171.7 of this subchapter), Type 304 or 304L must be used... the lading. (b) Any steel casting, steel forging, steel structural shape or carbon steel plate used to...

49 CFR 179.400-5 - Materials.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400-5 Materials. (a) Stainless steel of ASTM A 240/A 240M (IBR, see § 171.7 of this subchapter), Type 304 or 304L must be used... the lading. (b) Any steel casting, steel forging, steel structural shape or carbon steel plate used to...

49 CFR 179.400-5 - Materials.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400-5 Materials. (a) Stainless steel of ASTM A 240/A 240M (IBR, see § 171.7 of this subchapter), Type 304 or 304L must be used... the lading. (b) Any steel casting, steel forging, steel structural shape or carbon steel plate used to...

Methods of measurement for semiconductor materials, process control, and devices

NASA Technical Reports Server (NTRS)

Bullis, W. M. (Editor)

1973-01-01

This progress report describes NBS activities directed toward the development of methods of measurement for semiconductor materials, process control, and devices. Significant accomplishments during this reporting period include design of a plan to provide standard silicon wafers for four-probe resistivity measurements for the industry, publication of a summary report on the photoconductive decay method for measuring carrier lifetime, publication of a comprehensive review of the field of wire bond fabrication and testing, and successful completion of organizational activity leading to the establishment of a new group on quality and hardness assurance in ASTM Committee F-1 on Electronics. Work is continuing on measurement of resistivity of semiconductor crystals; characterization of generation-recombination-trapping centers in silicon; study of gold-doped silicon; development of the infrared response technique; evaluation of wire bonds and die attachment; and measurement of thermal properties of semiconductor devices, delay time and related carrier transport properties in junction devices, and noise properties of microwave diodes.

7075-T6 and 2024-T351 Aluminum Alloy Fatigue Crack Growth Rate Data

NASA Technical Reports Server (NTRS)

Forth, Scott C.; Wright, Christopher W.; Johnston, William M., Jr.

2005-01-01

Experimental test procedures for the development of fatigue crack growth rate data has been standardized by the American Society for Testing and Materials. Over the past 30 years several gradual changes have been made to the standard without rigorous assessment of the affect these changes have on the precision or variability of the data generated. Therefore, the ASTM committee on fatigue crack growth has initiated an international round robin test program to assess the precision and variability of test results generated using the standard E647-00. Crack growth rate data presented in this report, in support of the ASTM roundrobin, shows excellent precision and repeatability.

49 CFR 192.63 - Marking of materials.

Code of Federal Regulations, 2011 CFR

2011-10-01

... thermoplastic fittings must be marked in accordance with ASTM D2513-87 (incorporated by reference, see § 192.7.... 9, 1989; 58 FR 14521, Mar. 18, 1993; Amdt. 192-76, 61 FR 26122, May 24, 1996; 61 FR 36826, July 15...

46 CFR 107.305 - Plans and information.

Code of Federal Regulations, 2013 CFR

2013-10-01

... systems. Marine Engineering (z) Plans required for marine engineering equipment and systems by Subchapter F of this chapter. Electrical Engineering (aa) Plans required for electrical engineering equipment... materials that do not conform to ABS or ASTM specifications, complete specifications, including chemical and...

16 CFR 1402.4 - Requirements to provide performance and technical data by labeling and instructions.

Code of Federal Regulations, 2014 CFR

2014-01-01

..._locations.html. (2) Color limit values shall be determined by ASTM D 1535-68, “Specifying Color by the... 1535-68 are available from the American Society for Testing and Materials, 1916 Race Street...

16 CFR 1402.4 - Requirements to provide performance and technical data by labeling and instructions.

Code of Federal Regulations, 2012 CFR

2012-01-01

..._locations.html. (2) Color limit values shall be determined by ASTM D 1535-68, “Specifying Color by the... 1535-68 are available from the American Society for Testing and Materials, 1916 Race Street...

Whole glove permeation of cyclohexanol through disposable nitrile gloves on a dextrous robot hand and comparison with the modified closed-loop ASTM F739 method 1. No fist clenching.

PubMed

Mathews, Airek R; Que Hee, Shane S

2017-04-01

The aim was to develop a whole glove permeation method for cyclohexanol to generate permeation parameter data for a non-moving dextrous robot hand (normalized breakthrough time t b , standardized breakthrough time t s , steady state permeation rate P s , and diffusion coefficient D). Four types of disposable powderless, unsupported, and unlined nitrile gloves from the same producer were investigated: Safeskin Blue and Kimtech Science Blue, Purple, and Sterling. The whole glove method developed involved a peristaltic pump for water circulation through chemically resistant Viton tubing to continually wash the inner surface of the test glove via holes in the tubing, a dextrous robot hand operated by a microprocessor, a chemically protective nitrile glove to protect the robot hand, an incubator to maintain 35°C temperature, and a hot plate to maintain 35°C at the sampling point of the circulating water. Aliquots of 1.0 mL were sampled at regular time intervals for the first 60 min followed by removal of 0.5 mL aliquots every hour to 8 hr. Quantification was by the internal standard method after gas chromatography-selective ion electron impact mass spectrometry using a non-polar capillary column. The individual glove values of t b and t s differed for the ASTM closed loop method except for Safeskin Blue, but did not for the whole glove method. Most of the kinetic parameters agreed within an order of magnitude for the two techniques. The order of most protective to least protective glove was Blue and Safeskin, then Purple followed by Sterling for the whole gloves. The analogous order for the modified F739 ASTM closed loop method was: Safeskin, Blue, Purple, and Sterling, almost the same as for the whole glove. The Sterling glove was "not recommended" from the modified ASTM data, and was "poor" from the whole glove data.

40 CFR 1065.701 - General requirements for test fuels.

Code of Federal Regulations, 2010 CFR

2010-07-01

... procedure 1 Light distillate and light blends with residual ASTM D975-07b. Diesel Middle distillate ASTM D6985-04a. Biodiesel (B100) ASTM D6751-07b. Intermediate and residual fuel All See § 1065.705. Gasoline Motor vehicle gasoline ASTM D4814-07a. Minor oxygenated gasoline blends ASTM D4814-07a. Alcohol Ethanol...

Fretting-corrosion at the modular tapers interface: Inspection of standard ASTM F1875-98.

PubMed

Bingley, Rachel; Martin, Alan; Manfredi, Olivia; Nejadhamzeeigilani, Mahdiyar; Oladokun, Abimbola; Beadling, Andrew Robert; Siddiqui, Sohail; Anderson, James; Thompson, Jonathan; Neville, Anne; Bryant, Michael

2018-05-01

Interest in the degradation mechanisms at the modular tapers interfaces has been renewed due to increased reported cases of adverse reactions to metal debris and the appearance of wear and corrosion at the modular tapers interfaces at revision. Over the past two decades, a lot of research has been expended to understand the degradation mechanisms, with two primary implant loading procedures and orientations used consistently across the literature. ASTM F1875-98 is often used as a guide to understand and benchmark the tribocorrosion processes occurring within the modular tapers interface. This article presents a comparison of the two methods outlined in ASTM F1875-98 as well as a critique of the standard considering the current paradigm in pre-clinical assessment of modular tapers.

Evaluation of a boron-nitrogen, phosphate-free fire-retardant treatment. Part I, Testing of Douglas-fir plywood per ASTM Standard D 5516-96

Treesearch

Jerrold E. Winandy; Michael J. Richards

2003-01-01

The objective of this work was to evaluate (a) the effects of a new boron– nitrogen, phosphate-free fire-retardant (FR) formulation on the initial strength of Douglas-fir AB-grade plywood and (b) the potential of this FR treatment to experience subsequent thermal degradation In-service when exposed to elevated temperatures. Test Method ASTM D 5516 was generally...

Demonstration of an In-Situ Friction-Sound Probe for Mapping Particle Size at Contaminated Sediment Sites

DTIC Science & Technology

2014-04-01

sedimentation according to the Stokes Law through pipettes (Plumb, 1981) or hydrometer (ASTM, 1988). Various optical techniques, electro-resistance (Coulter...used by the contracting laboratory (ASTM, 1998) is a combined mechanical sieving and hydrometer method. The sieves are used to quantify particle sizes...in the sand range (> 63 µm) and larger, and a sedimentation- hydrometer technique is used to quantify the silt and clay size ranges (< 63 µm

Characterization and Evaluation of TiB2-AlN Composites for Armor Applications

DTIC Science & Technology

2013-09-01

identified structural defects and studied the fracture mechanisms (15, 16). 2 2. Experimental One TiB2 powder was used for this study. The TiB2...on phase formation and grain size effects compounded with residual stress on the fracture mechanisms . However, it was determined that the composite...Temperature. Annu. Book ASTM Stand. 2002, Vol. 15.01. 18. ASTM C 1421-10. Standard Test Methods for Determination of Fracture Toughness of

Validation of Proposed Metrics for Two-Body Abrasion Scratch Test Analysis Standards

NASA Technical Reports Server (NTRS)

Kobrick, Ryan L.; Klaus, David M.; Street, Kenneth W., Jr.

2011-01-01

The objective of this work was to evaluate a set of standardized metrics proposed for characterizing a surface that has been scratched from a two-body abrasion test. This is achieved by defining a new abrasion region termed Zone of Interaction (ZOI). The ZOI describes the full surface profile of all peaks and valleys, rather than just measuring a scratch width as currently defined by the ASTM G 171 Standard. The ZOI has been found to be at least twice the size of a standard width measurement, in some cases considerably greater, indicating that at least half of the disturbed surface area would be neglected without this insight. The ZOI is used to calculate a more robust data set of volume measurements that can be used to computationally reconstruct a resultant profile for detailed analysis. Documenting additional changes to various surface roughness parameters also allows key material attributes of importance to ultimate design applications to be quantified, such as depth of penetration and final abraded surface roughness. Data are presented to show that different combinations of scratch tips and abraded materials can actually yield the same scratch width, but result in different volume displacement or removal measurements and therefore, the ZOI method is more discriminating than the ASTM method scratch width. Furthermore, by investigating the use of custom scratch tips for our specific needs, the usefulness of having an abrasion metric that can measure the displaced volume in this standardized manner, and not just by scratch width alone, is reinforced. This benefit is made apparent when a tip creates an intricate contour having multiple peaks and valleys within a single scratch. This work lays the foundation for updating scratch measurement standards to improve modeling and characterization of three-body abrasion test results.

ASTM F739 method for testing the permeation resistance of protective clothing materials: critical analysis with proposed changes in procedure and test-cell design.

PubMed

Anna, D H; Zellers, E T; Sulewski, R

1998-08-01

ASTM (American Society for Testing and Materials) Method F739-96 specifies a test-cell design and procedures for measuring the permeation resistance of chemical protective clothing. Among the specifications are open-loop collection stream flow rates of 0.050 to 0.150 L/min for a gaseous medium. At elevated temperatures the test must be maintained within 1 degree C of the set point. This article presents a critical analysis of the effect of the collection stream flow rate on the measured permeation rate and on the temperature uniformity within the test cell. Permeation tests were conducted on four polymeric glove materials with 44 solvents at 25 degrees C. Flow rates > 0.5 L/min were necessary to obtain accurate steady-state permeation rate (SSPR) values in 25 percent of the tests. At the lower flow rates the true SSPR typically was underestimated by a factor of two or less, but errors of up to 33-fold were observed. No clear relationship could be established between the need for a higher collection stream flow rate and either the vapor pressure or the permeation rate of the solvent, but test results suggest that poor mixing within the collection chamber was a contributing factor. Temperature gradients between the challenge and collection chambers and between the bottom and the top of the collection chamber increased with the water-bath temperature and the collection stream flow rate. Use of a test cell modified to permit deeper submersion reduced the gradients to < or = 0.5 degrees C. It is recommended that all SSPR measurements include verification of the adequacy of the collection stream flow rate. For testing at nonambient temperatures, the modified test cell described here could be used to ensure temperature uniformity throughout the cell.

ASTM D395 Short-Term Compression Set of Solid (Non-Porous) Siloxanes: SE 1700, Sylgard 184, and "New" M9787

DOE Office of Scientific and Technical Information (OSTI.GOV)

Small, Ward; Pearson, Mark A.; Jensen, Wayne A.

2015-09-13

Compression set of solid (non-porous) Dow Corning SE 1700, Sylgard 184, and “new” M9787 siloxane elastomers was measured according to ASTM D395 Method B. Specimens of SE 1700 were made using (1) the manufacturer’s suggested cure of 150°C for 30 min and (2) an extended cure of 60°C for 6 h and 150°C for 1 h followed by a post-cure under nitrogen purge at 125°C for 12 h. Four specimens of each material were aged at 25-27% compressive strain at 70°C under nitrogen purge for 70 h. Final thickness of each specimen was measured after a 30-min cooling/relaxation period, andmore » compression set relative to deflection was calculated. The average compression set relative to deflection was 6.0% for SE 1700 made using the extended cure and post-cure, 11.3% for SE 1700 made using the manufacturer’s suggested cure, 12.1% for Sylgard 184, and 1.9% for M9787. The extended cure and post-cure reduced the amount of compression set in SE 1700.« less

Effect of stress ratio on the fatigue behaviour of glass/epoxy composite

NASA Astrophysics Data System (ADS)

Syayuthi, A. R. A.; Majid, M. S. Abdul; Ridzuan, M. J. M.; Basaruddin, K. S.; Peng, T. L.

2017-10-01

The effect of stress ratio on the fatigue behaviour of the GFRE composite has been investigated. The glass fibre reinforced epoxy (GFRE) composite plates were fabricated using vacuum infusion method. Static tensile was performed in accordance with the ASTM D5766 standard, and the cyclic test was conducted according to ASTM D3479 with three different stress ratio, R = 0, 0.5, -1. Static tensile tests were carried out to determine the ultimate strength of this composite. Subsequently, fatigue tests loads ranging from 30% to 90% of the ultimate load were applied to each specimen. The S-N curve of different stress ratio loading of fibreglass/epoxy composites was then established. The results show that the number of cycles to failure increases as the loading is decreased. The specimens for fatigue tests loads 30% at R = 0 and -1 recorded the highest number of cycles at 2 million cycles. The results obtained from this test indicated a significant life reduction for R = -1 compared with the tension-tension loading, with the life reduction for R = -1 being greatest. The fatigue behaviour of the GFRE composite materials is not only influenced by the percentage of fatigue tests load but with different of stress ratio.

76 FR 1459 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM International

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-10

... Production Act of 1993-ASTM International Notice is hereby given that, on December 6, 2010, pursuant to.... (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with the...

The Acoustical Properties of the Polyurethane Concrete Made of Oyster Shell Waste Comparing Other Concretes as Architectural Design Components

NASA Astrophysics Data System (ADS)

Setyowati, Erni; Hardiman, Gagoek; Purwanto

2018-02-01

This research aims to determine the acoustical properties of concrete material made of polyurethane and oyster shell waste as both fine aggregate and coarse aggregate comparing to other concrete mortar. Architecture needs aesthetics materials, so the innovation in architectural material should be driven through the efforts of research on materials for building designs. The DOE methods was used by mixing cement, oyster shell, sands, and polyurethane by composition of 160 ml:40 ml:100 ml: 120 ml respectively. Refer to the results of previous research, then cement consumption is reduced up to 20% to keep the concept of green material. This study compared three different compositions of mortars, namely portland cement concrete with gravel (PCG), polyurethane concrete of oyster shell (PCO) and concrete with plastics aggregate (PCP). The methods of acoustical tests were conducted refer to the ASTM E413-04 standard. The research results showed that polyurethane concrete with oyster shell waste aggregate has absorption coefficient 0.52 and STL 63 dB and has a more beautiful appearance when it was pressed into moulding. It can be concluded that polyurethane concrete with oyster shell aggregate (PCO) is well implemented in architectural acoustics-components.

Development of a two-body wet abrasion test method with attention to the effects of reused abradant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blau, Peter Julian; Dehoff, Ryan R

2012-01-01

Abrasive wear is among the most common and costliest causes for material wastage, and it occurs in many forms. A simple method has been developed to quantify the response of metals and alloys to two-body wet abrasion. A metallographic polishing machine was modified to create a disk-on-flat sliding test rig. Adhesive-backed SiC grinding papers were used under fixed load and speed to rank the abrasive wear of seven alloy steels, some of which are candidates for drill cones for geothermal drilling. Standardized two-body abrasion tests, like those described in ASTM G132, feed unused abrasive into the contact; however, the currentmore » work investigated whether useful rankings could still be obtained with a simpler testing configuration in which specimens repeatedly slide on the same wear path under water-lubricated conditions. Tests using abrasive grit sizes of 120 and 180 resulted in the same relative ranking of the alloys although the coarser grit produced more total wear. Wear decreased when the same abrasive disk was re-used for up to five runs, but the relative rankings of the steels remained the same. This procedure was presented to ASTM Committee G2 on Wear and Erosion as a potential standard test for wet two-body abrasive wear.« less

Degradation Testing of Fluorotelomer-based polymers (FTPs)

EPA Science Inventory

Over the last decade, concern about sources of per and polyfluorochemicals (PFCs) have led to an increasing need for information on the microbial and/or abiotic degradation of polymer materials that contain PFC structural fragments that may be released. EPA, OECD, ASTM and other...

The Importance of Play: Part Two

ERIC Educational Resources Information Center

Exceptional Parent, 2008

2008-01-01

The International Playground Equipment Manufacturers Association (IPEMA) is a non-profit membership association of playground equipment and surfacing companies. IPEMA's primary mission is to provide playground equipment and surfacing with independently tested safety certification to meet American Society for Testing and Materials (ASTM) standards…

Dowel Bar Retrofit Mix Design and Specification : Technical Report

DOT National Transportation Integrated Search

2012-01-01

Current INDOT specifications for repair materials to be used in dowel bar retrofit (DBR) applications (Sections 507.08 and 901.07 of INDOTs Book of Specifications) are based, in large part, on the requirements of ASTM C 928 and the manufacturer-pr...

VIBRATION TESTING OF RESILIENT PACKAGE CUSHIONING MATERIALS

DTIC Science & Technology

government and industry. Testing equipment which meets tentative ASTM requirements was developed. Preliminary tests were conducted on a resilient expanded ... polystyrene foam (in 3 densities) and a polyether urethane foam (in one density). When vibrated under static loads known to provide optimum shock

Lithologic characterization of active ITD aggregate sources and implications for aggregate quality.

DOT National Transportation Integrated Search

2014-03-01

Aggregate from 40 material sources across Idaho were sampled and the lithologies identified quantitatively. Aggregate compositions are compared with commercial AASHTO T 303 and ASTM C1293 results and the geologic map of Idaho to identify those rock t...

16 CFR § 1402.4 - Requirements to provide performance and technical data by labeling and instructions.

Code of Federal Regulations, 2013 CFR

2013-01-01

..._locations.html. (2) Color limit values shall be determined by ASTM D 1535-68, “Specifying Color by the... 1535-68 are available from the American Society for Testing and Materials, 1916 Race Street...

The Use of AC-DC-AC Methods in Assessing Corrosion Resistance Performance of Coating Systems for Magnesium Alloys

NASA Astrophysics Data System (ADS)

McCune, Robert C.; Upadhyay, Vinod; Wang, Yar-Ming; Battocchi, Dante

The potential utility of AC-DC-AC electrochemical methods in comparative measures of corrosion-resisting coating system performance for magnesium alloys under consideration for the USAMP "Magnesium Front End Research and Development" project was previously shown in this forum [1]. Additional studies of this approach using statistically-designed experiments have been conducted with focus on alloy types, pretreatment, topcoat material and topcoat thickness as the variables. Additionally, sample coupons made for these designed experiments were also subjected to a typical automotive cyclic corrosion test cycle (SAE J2334) as well as ASTM B117 for comparison of relative performance. Results of these studies are presented along with advantages and limitations of the proposed methodology.

Smart Natural Fiber Reinforced Plastic (NFRP) Composites Based On Recycled Polypropylene in The Presence Kaolin

NASA Astrophysics Data System (ADS)

Suharty, N. S.; Ismail, H.; Diharjo, K.; Handayani, D. S.; Lestari, W. A.

2017-07-01

Composites contain double filler material which act as reinforcement and flame retardants of recycled polypropylene (rPP)/kaolin(Kao)/palm oil empty bunch fiber (PEBF) have been succesfully prepared. The composites were synthesized through reactively solution method, using coupling agent PP-g-AA and compatibilizer DVB. The effect of double filler [Kao/PEBF] were investigated flexural strength (FS), inflammability, and morphology. Mechanical testing result in accordance to ASTM D790, the FS of rPP/DVB/PP-g-AA/Kao+ZB/PEBF composite was 48% higher than that of rPP matrix. Moreover, flexural modulus (FM) was significantly improved by 56% as compared to that of rPP matrix. The scanning electron images (SEM) shown good dispersion of [Ka/PEBF] and good filler-matrix interaction. The inflammability testing result which is tested using ASTM D635, showed that the flame resistance of rPP/DVB/PP-g-AA/Kao+ZB/PEBF composite was improve by increasing of time to ignition (TTI) about 857% and burning rate (BR) decreasing to 66% compared to the raw material rPP matrix. In the same time, the addition of 20% (w/w) PEBF as a second filler to form rPP/DVB/PP-g-AA/Kao+ZB/PEBF composites (F5) is able to increase: the FS by 17.5%, the FM by 19%, the TTI by 7.6% and the BR by 3.7% compared to the composite without PEBF (F2).

Investigation on mechanical properties of basalt composite fabrics (experiment study)

NASA Astrophysics Data System (ADS)

Talebi Mazraehshahi, H.; Zamani, H.

2010-06-01

To fully appreciate the role and application of composite materials to structures, correct understanding of mechanical behaviors required for selection of optimum material. Fabric reinforced composites are composed of a matrix that is reinforced with pliable fabric, glass fabric is most popular reinforcement for different application specially in aircraft structure, although other fabric material are also used. At this study new fabric material called basalt with epoxy resin introduced and mechanical behaviors of this material investigated from view point of testing. For this study two type of fabric with different thickness used. Comparison between this composite reinforcement with popular reinforcement as carbon, glass, kevlar performed. To determine mechanical properties of epoxy based basalt fabric following test procedure performed : 1). Tensile testing according to ASTM D3039 in 0° and 90° direction to find ultimate strength in tension and shear, modulus of elasticity, elangation and ultimate strain. 2). Compression testing according to EN 2850 ultimate compression strength and maximum deformation under compression loading. 3). Shear testing according to ASTM D3518-94 to find in plane shear response of polymer matrix composites materials. 4). Predict flexural properties of sandwich construction which manufactured from basalt facing with PVC foam core according to ASTM C393-94. Material strength properties must be based on enough tests of material to meet the test procedure specifications [1]. For this reason six specimens were manufactured for testing and the tests were performed on them using an INSTRON machine model 5582. In the study, the effect of percent of resin in basalt reinforced composite was investigated. Also the weights of the ballast based composites with different percent of resin were measured with conventional composites. As the weight is an important parameter in aerospace industry when the designer wants to replace one material with another, the effect of weight must be considered. Weight measurement showed that the replacement of glass fabric reinforcement with basalt fabric has little effect on weight. Investigation also shows that mechanical behavior of basalt fabric is higher than glass fabric. This is due to the excellent mechanical properties of the ballast fabric such as Young modulus and strength in compare with the glass fabric. Figure1 shows the samples which used for tensile testing in warp direction.

Effect of the raw material composition of fabrics on the Limiting Oxygen Index (LOI)

NASA Technical Reports Server (NTRS)

Jeler, S.; Ceric, B.

1986-01-01

The raw material composition of fabrics is one of the most important factors for LOI value. LOI value was determined in samples of varying composition composed of cellulose, protein, and synthetic fibers and their mixtures, based on ASTM D 2863-76. Cellulose fibers and their mixtures exhibited the lowest value, while synthetic fibers had the highest LOI value.

Analytical modeling of fire growth on fire-resistive wood-based materials with changing conditions

Treesearch

Mark A. Dietenberger

2006-01-01

Our analytical model of fire growth for the ASTM E 84 tunnel, which simultaneously predicts heat release rate, flame-over area, and pyrolysis area as functions of time for constant conditions, was documented in the 2001 BCC Symposium for different treated wood materials. The model was extended to predict ignition and fire growth on exterior fire-resistive structures...

Evaluating physical property changes for small-diameter, plantation-grown southern pine after in situ polymerization of an acrylic monomer

Treesearch

Richard Bergman; Rebecca E. Ibach; Constantine LaPasha; Joseph Denig

2009-01-01

Because of the large percentage of juvenile wood in small-diameter southern pine, this material has lower strength properties compared with the historic published values in the ASTM Standard D2555. Finding new, simple, and inexpensive ways of increasing these strength properties would increase the use of this material for residential construction. For this study, we...

76 FR 13631 - Food and Drug Administration Modernization Act of 1997: Modifications to the List of Recognized...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-14

... equipment. I. Tissue Engineering 15-25 ASTM F2312--10 Standard ASTM F2312-10. Terminology Relating to Tissue Engineered Medical Products. 15-26 ASTM F2211--04 Standard ASTM F2211-04. Classification for Tissue...

Decolorization improves the fuel properties of algal biodiesel from Isochrysis sp.

USDA-ARS?s Scientific Manuscript database

Results from the comprehensive fuel testing according to the American Society for Testing and Materials International (ASTM) standards of an alkenone-free and decolorized biodiesel produced from the industrially grown marine microalgae Isochrysis sp. are presented. Fatty acid methyl ester (FAME) pro...

75 FR 27987 - Certain Welded Stainless Steel Pipes From the Republic of Korea: Final Results of Antidumping...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-19

... forth by the American Society for Testing and Materials (ASTM) for the welded form of chromium-nickel... configuration and welding along the seam. WSSP is a commodity product generally used as a conduit to transmit...

STEROID HORMONES AS BIOMARKERS OF ENDOCRINE DISRUPTION IN WILDLIFE. IN: ENVIRONMENTAL TOXICOLOGY AND RISK ASSESSMENT

EPA Science Inventory

Standardization of Biomarkers for Endocrine Disruption and Environmental Assessment. 8th Volume, ASTM STP 1364. D.S. Henshel, M.C. Black, and M.C. Harrass, Editors. American Society for Testing and Materials, West Conshohocken, PA. Pp. 254-270.

ALKALI-ACTIVATED CEMENT (AAC) AS A SUSTAINABLE BUILDING MATERIAL

EPA Science Inventory

It is expected that this project will result in 1) production of technical paper(s) and presentations that better explains the relationships between chemical, microstructural, and performance properties of AACs, 2) commercially viable AAC formulae that pass the ASTM C1157 stan...

Seismic performance of circular reinforced concrete bridge columns constructed with grade 80 reinforcement.

DOT National Transportation Integrated Search

2014-08-01

This project assessed the use of ASTM A706 Grade 80 reinforcing bars in reinforced concrete columns. : Grade 80 is not currently allowed in reinforced concrete columns due to lack of information on the : material characteristics and column performanc...

46 CFR 151.01-2 - Incorporation by reference.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., are: American Society for Nondestructive Testing (ASNT) 4153 Arlingate Road, Caller #28518, Columbus... Certification in Nondestructive Testing” 151.04-7(c)(2) American Society of Mechanical Engineers (ASME..., Nondestructive Examination (1986) 151.04-7(a)(1) American Society for Testing and Materials (ASTM) 100 Barr...

Alternative Test Method for Olefins in Gasoline

EPA Pesticide Factsheets

This action proposes to allow for an additional alternative test method for olefins in gasoline, ASTM D6550-05. The allowance of this additional alternative test method will provide more flexibility to the regulated industry.

40 CFR 98.254 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... methods. (1) ASTM D4809-06 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb...) Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (incorporated...

A novel route for processing cobalt–chromium–molybdenum orthopaedic alloys

PubMed Central

Patel, Bhairav; Inam, Fawad; Reece, Mike; Edirisinghe, Mohan; Bonfield, William; Huang, Jie; Angadji, Arash

2010-01-01

Spark plasma sintering has been used for the first time to prepare the ASTM F75 cobalt–chromium–molybdenum (Co–Cr–Mo) orthopaedic alloy composition using nanopowders. In the preliminary work presented in this report, the effect of processing variables on the structural features of the alloy (phases present, grain size and microstructure) has been investigated. Specimens of greater than 99.5 per cent theoretical density were obtained. Carbide phases were not detected in the microstructure but oxides were present. However, harder materials with finer grains were produced, compared with the commonly used cast/wrought processing methods, probably because of the presence of oxides in the microstructure. PMID:20200035

40 CFR 799.5085 - Chemical testing requirements for first group of high production volume chemicals (HPV1).

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Toxicity to Plants (Algae): ASTM E 1218 Test Group 2 for C1: 1. Chronic Toxicity to Daphnia: ASTM E 1193 2. Toxicity to Plants (Algae): ASTM E 1218 The following are the special conditions for C1, C2, C3, C4, C5.... Acute Toxicity to Daphnia: ASTM E 729 2. Toxicity to Plants (Algae): ASTM E 1218 Test Group 2 for C2: 1...

40 CFR 1065.720 - Liquefied petroleum gas.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., C3H8 Minimum, 0.85 m3/m3 ASTM D2163-05. Vapor pressure at 38 °C Maximum, 1400 kPa ASTM D1267-02 or 2598-022. Volatility residue (evaporated temperature, 35 °C) Maximum, −38 °C ASTM D1837-02a. Butanes Maximum, 0.05 m3/m3 ASTM D2163-05. Butenes Maximum, 0.02 m3/m3 ASTM D2163-05. Pentenes and heavier Maximum...

Re-cycling of sugar-ash: a raw feed material for rotary kilns.

PubMed

Kantiranis, Nikolaos

2004-01-01

Large amounts of sugar-ash, a material rich in calcium carbonate, are produced as a by-product in the Greek Sugar Industry. This work explores the possibility of re-cycling sugar-ash for use in the lime industry. A representative sample of sugar-ash from the Plati Imathias sugar plant was studied by PXRD, TG/DTG, calcination experiments at temperatures between 650 and 1150 degrees C and experiments to determine the quality of the quicklime produced at temperatures between 850 and 1150 degrees C following methods described in ASTM C110 standard. The sugar-ash was found to consist of 90 wt% calcium rich minerals (calcite and monohydrocalcite) and 10 wt% amorphous material. Traces of quartz were also detected. The quicklime of highest quality was produced at 950 degrees C. It is concluded that this "useless" material (sugar-ash) can be re-cycled for use in rotary kilns in the lime industry at calcination temperatures up to 950-1000 degrees C.

Efficacy of a surfactant-based wound dressing on biofilm control.

PubMed

Percival, Steven L; Mayer, Dieter; Salisbury, Anne-Marie

2017-09-01

The aim of this study was to evaluate the efficacy of both a nonantimicrobial and antimicrobial (1% silver sulfadiazine-SSD) surfactant-based wound dressing in the control of Pseudomonas aeruginosa, Enterococcus sp, Staphylococcus epidermidis, Staphylococcus aureus, and methicillin-resistant S. aureus (MRSA) biofilms. Anti-biofilm efficacy was evaluated in numerous adapted American Standards for Testing and Materials (ASTM) standard biofilm models and other bespoke biofilm models. The ASTM standard models employed included the Minimum biofilm eradication concentration (MBEC) biofilm model (ASTM E2799) and the Centers for Disease Control (CDC) biofilm reactor model (ASTM 2871). Such bespoke biofilm models included the filter biofilm model and the chamberslide biofilm model. Results showed complete kill of microorganisms within a biofilm using the antimicrobial surfactant-based wound dressing. Interestingly, the nonantimicrobial surfactant-based dressing could disrupt existing biofilms by causing biofilm detachment. Prior to biofilm detachment, we demonstrated, using confocal laser scanning microscopy (CLSM), the dispersive effect of the nonantimicrobial surfactant-based wound dressing on the biofilm within 10 minutes of treatment. Furthermore, the non-antimicrobial surfactant-based wound dressing caused an increase in microbial flocculation/aggregation, important for microbial concentration. In conclusion, this nonantimicrobial surfactant-based wound dressing leads to the effective detachment and dispersion of in vitro biofilms. The use of surfactant-based wound dressings in a clinical setting may help to disrupt existing biofilm from wound tissue and may increase the action of antimicrobial treatment. © 2017 by the Wound Healing Society.

40 CFR 312.11 - References.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the requirements set forth in §§ 312.23 through 312.31: (a) The procedures of ASTM International... Site Assessment Process.” (b) The procedures of ASTM International Standard E2247-08 entitled “Standard... or Rural Property.” This standard is available from ASTM International at http://www.astm.org, 1-610...