The testing effect and analogical problem-solving.

PubMed

Peterson, Daniel J; Wissman, Kathryn T

2018-06-25

Researchers generally agree that retrieval practice of previously learned material facilitates subsequent recall of same material, a phenomenon known as the testing effect. There is debate, however, about when such benefits transfer to related (though not identical) material. The current study examines the phenomenon of transfer in the domain of analogical problem-solving. In Experiments 1 and 2, learners were presented a source text describing a problem and solution to read which was subsequently either restudied or recalled. Following a short (Experiment 1) or long (Experiment 2) delay, learners were given a new target text and asked to solve a problem. The two texts shared a common structure such that the provided solution for the source text could be applied to solve the problem in the target text. In a combined analysis of both experiments, learners in the retrieval practice condition were more successful at solving the problem than those in the restudy condition. Experiment 3 explored the degree to which retrieval practice promotes cued versus spontaneous transfer by manipulating whether participants were provided with an explicit hint that the source and target texts were related. Results revealed no effect of retrieval practice.

A Laboratory Exercise with Related Rates.

ERIC Educational Resources Information Center

Sworder, Steven C.

A laboratory experiment, based on a simple electric circuit that can be used to demonstrate the existence of real-world "related rates" problems, is outlined and an equation for voltage across the capacitor terminals during discharge is derived. The necessary materials, setup methods, and experimental problems are described. A student laboratory…

ANSYS tools in modeling tires

NASA Technical Reports Server (NTRS)

Ali, Ashraf; Lovell, Michael

1995-01-01

This presentation summarizes the capabilities in the ANSYS program that relate to the computational modeling of tires. The power and the difficulties associated with modeling nearly incompressible rubber-like materials using hyperelastic constitutive relationships are highlighted from a developer's point of view. The topics covered include a hyperelastic material constitutive model for rubber-like materials, a general overview of contact-friction capabilities, and the acoustic fluid-structure interaction problem for noise prediction. Brief theoretical development and example problems are presented for each topic.

Pet Problems at Home: Pet Problems in the Community.

ERIC Educational Resources Information Center

Soltow, Willow

1984-01-01

Discusses problems of pets in the community, examining the community's role related to disruptive pets and pet overpopulation. Also discusses pet problems at home, offering advice on selecting a pet, meeting a pet's needs, and disciplining pets. Includes a list of books, films/filmstrips, teaching materials, and various instructional strategies.…

Research requirements to improve reliability of civil helicopters

NASA Technical Reports Server (NTRS)

Dougherty, J. J., III; Barrett, L. D.

1978-01-01

The major reliability problems of the civil helicopter fleet as reported by helicopter operational and maintenance personnel are documented. An assessment of each problem is made to determine if the reliability can be improved by application of present technology or whether additional research and development are required. The reliability impact is measured in three ways: (1) The relative frequency of each problem in the fleet. (2) The relative on-aircraft manhours to repair, associated with each fleet problem. (3) The relative cost of repair materials or replacement parts associated with each fleet problem. The data reviewed covered the period of 1971 through 1976 and covered only turbine engine aircraft.

Problems of the high-cycle fatigue of the materials intended for the parts of modern gas-turbine engines and power plants

NASA Astrophysics Data System (ADS)

Petukhov, A. N.

2010-10-01

The problems related to the determination of the life of the structural materials applied for important parts in gas-turbine engines and power plants from the results of high-cycle fatigue tests are discussed. Methods for increasing the reliability of the high-cycle fatigue characteristics and the factors affecting the operational reliability are considered.

An Alternative Time for Telling: When Conceptual Instruction Prior to Problem Solving Improves Mathematical Knowledge

ERIC Educational Resources Information Center

Fyfe, Emily R.; DeCaro, Marci S.; Rittle-Johnson, Bethany

2014-01-01

Background: The sequencing of learning materials greatly influences the knowledge that learners construct. Recently, learning theorists have focused on the sequencing of instruction in relation to solving related problems. The general consensus suggests explicit instruction should be provided; however, when to provide instruction remains unclear.…

The Speaker Respoken: Material Rhetoric as Feminist Methodology.

ERIC Educational Resources Information Center

Collins, Vicki Tolar

1999-01-01

Presents a methodology based on the concept of "material rhetoric" that can help scholars avoid problems as they reclaim women's historical texts. Defines material rhetoric and positions it theoretically in relation to other methodologies, including bibliographical studies, reception theory, and established feminist methodologies. Illustrates…

Comparison of highway striping materials.

DOT National Transportation Integrated Search

1980-01-01

This study was undertaken to investigate problems relating to the durability of pavement striping materials used by the Department. The research was limited to an evaluation of the durability and retroreflectance characteristics of selected paints, t...

Finite element analysis of fretting contact for nonhomogenous materials

NASA Astrophysics Data System (ADS)

Korkmaz, Y. M.; Coker, D.

2018-01-01

Fretting problem arises in the case of relatively small sliding motion between contacting surfaces. Fatigue life of the components that are in contact with each other, especially in rotorcraft may be significantly reduced due to fretting. The purpose of this study is to investigate material inhomogeneity near the contact region on the fretting problem in a cylindrical on flat contact configuration. A finite element (FE) model was constructed by using commercial finite element package ABAQUSTMto study partial sliding and stress concentrations. In order to investigate the effect of material inhomogeneity, the fretting contact is analyzed by introducing voids near the contact region. The void size and an array of voids is introduced into the substrate. The results are compared in terms of pressure, shear traction, tangential stress magnitudes and relative slip between the contacting materials.

Family Material Hardship and Chinese Adolescents’ Problem Behaviors: A Moderated Mediation Analysis

PubMed Central

Sun, Wenqiang; Li, Dongping; Zhang, Wei; Bao, Zhenzhou; Wang, Yanhui

2015-01-01

In the current study, we examined a moderated mediation model using the risk and resilience framework. Specifically, the impact of family material hardship on adolescent problem behaviors was examined in a Chinese sample; we used the family stress model framework to investigate parental depression and negative parenting as potential mediators of the relation between family material hardship and adolescents’ problem behaviors. In addition, based on resilience theory, we investigated adolescents’ resilience as a potential protective factor in the development of their internalizing and externalizing problems. Participants included 1,419 Chinese adolescents (mean age = 15.38 years, SD = 1.79) and their primary caregivers. After controlling for covariates (age, gender, location of family residence, and primary caregiver), we found that parental depression and negative parenting mediated the association between family material hardship and adolescents’ problem behaviors. Furthermore, the adolescent resilience moderated the relationship between negative parenting and internalizing problems in a protective-stabilizing pattern; in addition, a protective-reactive pattern also emerged when adolescent resilience was examined as a moderator of the relationship between negative parenting and externalizing problems. These findings contribute to a comprehensive understanding of the mechanisms of risk and resilience in youth development. Moreover, the findings have important implications for the prevention of adolescent problem behaviors. PMID:26010256

Comparison of highway striping materials : installation report.

DOT National Transportation Integrated Search

1980-01-01

This study has been undertaken to investigate problems relating to the durability of highway striping materials used by the Department The research is limited to an evaluation of the durability and retroreflectance characteristics of selected paints,...

Green's functions for dislocations in bonded strips and related crack problems

NASA Technical Reports Server (NTRS)

Ballarini, R.; Luo, H. A.

1990-01-01

Green's functions are derived for the plane elastostatics problem of a dislocation in a bimaterial strip. Using these fundamental solutions as kernels, various problems involving cracks in a bimaterial strip are analyzed using singular integral equations. For each problem considered, stress intensity factors are calculated for several combinations of the parameters which describe loading, geometry and material mismatch.

Adult Nutrition Education Materials. January 1982-October 1988. Quick Bibliography Series.

ERIC Educational Resources Information Center

Irving, Holly Berry

This annotated bibliography of materials available from the National Agricultural Library through interlibrary loan to local libraries focuses on nutrition and dietetics as they relate to physical health and special health problems. The bibliography was derived from online searches of the AGRICOLA database, and materials include audiovisuals,…

Applications of NASTRAN to nuclear problems

NASA Technical Reports Server (NTRS)

Spreeuw, E.

1972-01-01

The extent to which suitable solutions may be obtained for one physics problem and two engineering type problems is traced. NASTRAN appears to be a practical tool to solve one-group steady-state neutron diffusion equations. Transient diffusion analysis may be performed after new levels that allow time-dependent temperature calculations are developed. NASTRAN piecewise linear anlaysis may be applied to solve those plasticity problems for which a smooth stress-strain curve can be used to describe the nonlinear material behavior. The accuracy decreases when sharp transitions in the stress-strain relations are involved. Improved NASTRAN usefulness will be obtained when nonlinear material capabilities are extended to axisymmetric elements and to include provisions for time-dependent material properties and creep analysis. Rigid formats 3 and 5 proved to be very convenient for the buckling and normal-mode analysis of a nuclear fuel element.

Delineation and management of sulfidic materials in Virginia highway corridors.

DOT National Transportation Integrated Search

2002-01-01

Excavation through sulfidic geologic materials during road construction has resulted in acid drainage related problems at numerous discrete locations across Virginia. Barren acidic roadbanks, and acidic runoff and fill seepage clearly cause local env...

[Health-related quality of life evaluation of elderly aged 65 years and over living at home].

PubMed

Jalenques, I; Auclair, C; Rondepierre, F; Gerbaud, L; Tourtauchaux, R

2015-06-01

To assess health-related quality of life in French adults aged 65 years and over, living at home, with a specific self-administered questionnaire, the LEIPAD, cross-culturally adapted in French. Elderly completed socio-demographic and medical questionnaires, a questionnaire about negative life events during the last 12 months and the LEIPAD. Data of 195 subjects (mean age: 72.6 years, men: 56.5%) were analyzed. The response rates to the LEIPAD scales were superior to 90%. Elderly reported on the whole a good health-related quality of life. Age had a negative effect on quality on life, which deteriorates over years. Age was correlated to the scales "Physical function", "Self-care", "Cognitive functioning" and "Sexual functioning". Elderly hospitalized in the last year had worse quality of life with a significant difference for "Physical function" scale. The number of health problems was positively correlated to "Physical function" scale. Elderly declaring at least one health problem had worse quality of life for this scale. Problems in couple, materials and financial problems had also negative effects on health-related quality of life. Our study highlights a good health-related quality of life for the majority of these adults aged 65 years and over, as well as the negative effect of age, health, couple, materials and financial problems on their quality of life. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

System simulation application for determining the size of daily raw material purchases at PT XY

NASA Astrophysics Data System (ADS)

Napitupulu, H. L.

2018-02-01

Every manufacturing company needs to implement green production, including PT XY as a marine catchment processing industry in Sumatera Utara Province. The company is engaged in the processing of squid for export purposes. The company’s problem relates to the absence of a decision on the daily purchase amount of the squid. The purchase of daily raw materials in varying quantities has caused companies to face the problem of excess raw materials or otherwise the lack of raw materials. The low purchase of raw materials will result in reduced productivity, while large purchases will lead to increased cooling costs for storage of excess raw materials, as well as possible loss of damage raw material. Therefore it is necessary to determine the optimal amount of raw material purchases every day. This can be determined by applying simulation. Application of system simulations can provide the expected optimal amount of raw material purchases.

The role of biomaterials as occupational hazards in dentistry.

PubMed

Hensten-Pettersen, A; Jacobsen, N

1990-06-01

Many of the biomaterials and auxilliary products used in dentistry are chemically and biologically reactive and may be of concern in occupational safety programmes. Observations from 1936 to 1975 indicated that most occupational problems were related to skin contact with procaine, soaps, eugenol, iodine, formalin, phenol, and other disinfectants. Methyl methacrylate monomer was identified as an irritant and allergen in the later part of this period. Investigations from 1975 to 1985 indicated that disinfectants and detergents were still important causes of dermatoses, whereas reactions to procaine had been replaced by reactions to pantocaine. Furthermore, adverse reactions to methyl methacrylate monomer and to elastomeric impression materials had replaced the former iodine, tricresol and eugenol reactions. In recent studies the frequency of occupation-related dermatoses varied from 21 per cent to 43 per cent, depending on the prevailing material usage in the various specialties. Reactions to local anaesthetics seemed to have disappeared. Transient, irritative reactions of the eyes and airways have been observed, mostly associated with exposure to volatiles from resin-based materials, X-ray chemicals and cleansers. The occupational problems related to biomaterials in dentistry seem to have been fairly constant over the years, reflecting the type of materials in common use, and with dermatological disorders being a tenacious companion. Neuropathological conditions in dental technicians have been associated with prolonged exposure to vapours of methyl methacrylate monomer. The more recent extensive use of volatile resin-based materials, and the use of protective gloves seems to have created new problems that need to be investigated.

Microgravity Processing of Oxide Superconductors

NASA Technical Reports Server (NTRS)

Olive, James R.; Hofmeister, William H.; Bayuzick, Robert J.; Vlasse, Marcus

1999-01-01

Considerable effort has been concentrated on the synthesis and characterization of high T(sub c) oxide superconducting materials. The YBaCuO system has received the most intense study, as this material has shown promise for the application of both thin film and bulk materials. There are many problems with the application of bulk materials- weak links, poor connectivity, small coherence length, oxygen content and control, environmental reactivity, phase stability, incongruent melting behavior, grain boundary contamination, brittle mechanical behavior, and flux creep. The extent to which these problems are intrinsic or associated with processing is the subject of controversy. This study seeks to understand solidification processing of these materials, and to use this knowledge for alternative processing strategies, which, at the very least, will improve the understanding of bulk material properties and deficiencies. In general, the phase diagram studies of the YBaCuO system have concentrated on solid state reactions and on the Y2BaCuO(x) + liquid yields YBa2Cu3O(7-delta) peritectic reaction. Little information is available on the complete melting relations, undercooling, and solidification behavior of these materials. In addition, rare earth substitutions such as Nd and Gd affect the liquidus and phase relations. These materials have promising applications, but lack of information on the high temperature phase relations has hampered research. In general, the understanding of undercooling and solidification of high temperature oxide systems lags behind the science of these phenomena in metallic systems. Therefore, this research investigates the fundamental melting relations, undercooling, and solidification behavior of oxide superconductors with an emphasis on improving ground based synthesis of these materials.

Development of Finnish Elementary Pupils' Problem-Solving Skills in Mathematics

ERIC Educational Resources Information Center

Laine, Anu; Näveri, Liisa; Ahtee, Maija; Pehkonen, Erkki

2014-01-01

The purpose of this study is to determine how Finnish pupils' problem-solving skills develop from the 3rd to 5th grade. As research data, we use one non-standard problem from pre- and post-test material from a three-year follow-up study, in the area of Helsinki, Finland. The problems in both tests consisted of four questions related to each other.…

Kramers-Kronig relations in Laser Intensity Modulation Method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tuncer, Enis

2006-01-01

In this short paper, the Kramers-Kronig relations for the Laser Intensity Modulation Method (LIMM) are presented to check the self-consistency of experimentally obtained complex current densities. The numerical procedure yields well defined, precise estimates for the real and the imaginary parts of the LIMM current density calculated from its imaginary and real parts, respectively. The procedure also determines an accurate high frequency real current value which appears to be an intrinsic material parameter similar to that of the dielectric permittivity at optical frequencies. Note that the problem considered here couples two different material properties, thermal and electrical, consequently the validitymore » of the Kramers-Kronig relation indicates that the problem is invariant and linear.« less

THE POLITICS OF RISK AND EU GOVERNANCE OF HUMAN MATERIAL

PubMed Central

Farrel, Anne-Maree

2012-01-01

This paper examines the politics of EU risk governance in relation to human material. It is argued that the political context has informed the way in which risks in relation to various types of human material have come to be defined as policy problems at EU level. In turn, this has influenced the design and/or persistence of institutional arrangements to manage such problems. It is further argued that this political context has resulted in a significant level of disconnection in risk governance in the area. This has happened in two ways. First, there has been a growing level of disconnection between institutional and stakeholder demands for a more expansive approach to risk governance in the area and the narrowly-circumscribed competence under Article 152(4)(a) EC, which permits the adoption of risk regulation regimes that set minimum standards of quality and safety in relation to blood, tissue/cells and organs. Second, it has led to the development of institutional arrangements that promote a bifurcated approach to risk governance, specifically in relation to blood and tissues/cells. Although a hybrid of traditional and new governance mechanisms have been employed to address this problem of disconnection, this has nevertheless added a further layer to already complex institutional arrangements for risk governance in the area. It is suggested that a more integrated approach to EU risk governance in relation to human material is needed. Implementing such an approach would contribute to greater clarity, transparency and accountability in decision-making processes, and this could enhance public trust in what is a politically-sensitive area of governance at EU level. PMID:23326180

Committee on renewable resources for industrial materials (Corrim)

Treesearch

Robert W. Meyer; Carol B. Ovens

1976-01-01

In recent years major emphasis has been placed on nonrenewable resources in relation to potential national problems that may arise from possible changes in materials supply or utilization. Renewable resources, however, have received disproportionately small attention in spite of their current importance as industrial raw materials and their potential for the future. In...

7 CFR Exhibit A to Subpart B of... - Grant Agreement-Growth Management and Housing Planning for Approved Designated Energy Impacted Areas

Code of Federal Regulations, 2011 CFR

2011-01-01

... met; (iii) Problems, delays, or adverse conditions which will materially affect attainment of planned... process which will improve local conditions and alleviate problems associated with increased coal or... Grantee programs, projects, related activities, and problems. (b) The Grantee shall inform the Grantor as...

Horticulture Materials for Agricultural Education Programs. Core Agricultural Education Curriculum, Central Cluster.

ERIC Educational Resources Information Center

Illinois Univ., Urbana. Office of Agricultural Communications and Education.

This curriculum guide contains five units with relevant problem areas for horticulture. These problem areas have been selected as suggested areas of study to be included in a core curriculum for secondary students enrolled in an agricultural education program. Each problem area includes some or all of the following components: related problem…

Global Positioning System Bibliography

DTIC Science & Technology

1992-03-01

Nev., November, pp. 110-121. Chrzanowski, A. (1987). " Experiencias con GPS en mediciones de deformaciones." Presented at: Workshop on New Techniques...Material Placed in Open Waters Area 2 - Material Properties Related to Navigation and Dredging Area 3 - Dredge Plant Equipment and Systems Processes Area 4...Positioning System." Proceedings of the Second International Symposium on Problems Related to the Redefinintion of North American Geodetic Networks

Vigilance problems in orbiter processing

NASA Technical Reports Server (NTRS)

Swart, William W.; Safford, Robert R.; Kennedy, David B.; Yadi, Bert A.; Barth, Timothy S.

1993-01-01

A pilot experiment was done to determine what factors influence potential performance errors related to vigilance in Orbiter processing activities. The selected activities include post flight inspection for burned gap filler material and pre-rollout inspection for tile processing shim material. It was determined that the primary factors related to performance decrement were the color of the target and the difficulty of the target presentation.

Bibliography of information on mechanics of structural failure (hydrogen embrittlement, protective coatings, composite materials, NDE)

NASA Technical Reports Server (NTRS)

Carpenter, J. L., Jr.

1976-01-01

This bibliography is comprised of approximately 1,600 reference citations related to four problem areas in the mechanics of failure in aerospace structures. The bibliography represents a search of the literature published in the period 1962-1976, the effort being largely limited to documents published in the United States. Listings are subdivided into the four problem areas: Hydrogen Embrittlement; Protective Coatings; Composite Materials; and Nondestructive Evaluation. An author index is included.

Thermal control of high energy nuclear waste, space option. [mathematical models

NASA Technical Reports Server (NTRS)

Peoples, J. A.

1979-01-01

Problems related to the temperature and packaging of nuclear waste material for disposal in space are explored. An approach is suggested for solving both problems with emphasis on high energy density waste material. A passive cooling concept is presented which utilized conduction rods that penetrate the inner core. Data are presented to illustrate the effectiveness of the rods and the limit of their capability. A computerized thermal model is discussed and developed for the cooling concept.

A pressure relaxation closure model for one-dimensional, two-material Lagrangian hydrodynamics based on the Riemann problem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kamm, James R; Shashkov, Mikhail J

2009-01-01

Despite decades of development, Lagrangian hydrodynamics of strengthfree materials presents numerous open issues, even in one dimension. We focus on the problem of closing a system of equations for a two-material cell under the assumption of a single velocity model. There are several existing models and approaches, each possessing different levels of fidelity to the underlying physics and each exhibiting unique features in the computed solutions. We consider the case in which the change in heat in the constituent materials in the mixed cell is assumed equal. An instantaneous pressure equilibration model for a mixed cell can be cast asmore » four equations in four unknowns, comprised of the updated values of the specific internal energy and the specific volume for each of the two materials in the mixed cell. The unique contribution of our approach is a physics-inspired, geometry-based model in which the updated values of the sub-cell, relaxing-toward-equilibrium constituent pressures are related to a local Riemann problem through an optimization principle. This approach couples the modeling problem of assigning sub-cell pressures to the physics associated with the local, dynamic evolution. We package our approach in the framework of a standard predictor-corrector time integration scheme. We evaluate our model using idealized, two material problems using either ideal-gas or stiffened-gas equations of state and compare these results to those computed with the method of Tipton and with corresponding pure-material calculations.« less

In Print or Out of Print? The Continuing Problem.

ERIC Educational Resources Information Center

Kayden, Mimi

1982-01-01

Briefly describes the problems encountered by libraries in attempting to purchase out-of-stock books and discusses some of the reasons for changes in the way publishers handle backlist materials, including sales volume and its relation to increased printing costs. (JL)

The role of damage-softened material behavior in the fracture of composites and adhesives

NASA Technical Reports Server (NTRS)

Ungsuwarungsri, T.; Knauss, W. G.

1986-01-01

Failure mechanisms of materials under very high strains experienced at and ahead of the crack tip such as formation, growth, and interaction of microvoids in ductile materials, microcracks in brittle solids or crazes in polymers and adhesives are represented by one-dimensional, nonlinear stress-strain relations possessing different ways by which the material loses capacity to carry load up to fracture or total separation. A double cantilever beam (DCB) type specimen is considered. The nonlinear material is confined to a thin strip between the two elastic beams loaded by a wedge. The problem is first modeled as a beam on a nonlinear foundation. The pertinent equation is solved numerically as a two-point boundary value problem for both the stationary and the quasi-stationay propagating crack. A finite element model is then used to model the problem in more detail in order to assess the adequacy of the beam model for the reduction of experimental data to determine in-situ properties of the thin interlayer.

Representative Structural Element - A New Paradigm for Multi-Scale Structural Modeling

DTIC Science & Technology

2016-07-05

developed by NASA Glenn Research Center based on Aboudi’s micromechanics theories [5] that provides a wide range of capabilities for modeling ...to use appropriate models for related problems based on the capability of corresponding approaches. Moreover, the analyses will give a general...interface of heterogeneous materials but also help engineers to use appropriate models for related problems based on the capability of corresponding

Focus On: Classroom Energy Materials. Publication Number 11895.

ERIC Educational Resources Information Center

Kocsis, Mitzie

The Massachusetts Dissemination Project presents this compendium of energy-related educational resources as a reference guide for persons interested in exploring energy problems, conservation techniques, and alternate energy sources with their students. Provided are brief descriptions of available bibliographies, classroom materials, publications,…

Bibliography of information on mechanics of structural failure

NASA Technical Reports Server (NTRS)

Carpenter, J. L., Jr.; Moya, N.; Shaffer, R. A.; Smith, D. M.

1973-01-01

A bibliography of approximately 1500 reference citations related to six problem areas in the mechanics of failure in aerospace structures is presented. The bibliography represents a search of the literature published in the ten year period 1962-1972 and is largely limited to documents published in the United States. Listings are subdivided into the six problem areas: (1) life prediction of structural materials; (2) fracture toughness data; (3) fracture mechanics analysis; (4) hydrogen embrittlement; (5) protective coatings; and (6) composite materials. An author index is included.

SYNTHESIS OF NOVEL ALL-DIELECTRIC GRATING FILTERS USING GENETIC ALGORITHMS

NASA Technical Reports Server (NTRS)

Zuffada, Cinzia; Cwik, Tom; Ditchman, Christopher

1997-01-01

We are concerned with the design of inhomogeneous, all dielectric (lossless) periodic structures which act as filters. Dielectric filters made as stacks of inhomogeneous gratings and layers of materials are being used in optical technology, but are not common at microwave frequencies. The problem is then finding the periodic cell's geometric configuration and permittivity values which correspond to a specified reflectivity/transmittivity response as a function of frequency/illumination angle. This type of design can be thought of as an inverse-source problem, since it entails finding a distribution of sources which produce fields (or quantities derived from them) of given characteristics. Electromagnetic sources (electric and magnetic current densities) in a volume are related to the outside fields by a well known linear integral equation. Additionally, the sources are related to the fields inside the volume by a constitutive equation, involving the material properties. Then, the relationship linking the fields outside the source region to those inside is non-linear, in terms of material properties such as permittivity, permeability and conductivity. The solution of the non-linear inverse problem is cast here as a combination of two linear steps, by explicitly introducing the electromagnetic sources in the computational volume as a set of unknowns in addition to the material unknowns. This allows to solve for material parameters and related electric fields in the source volume which are consistent with Maxwell's equations. Solutions are obtained iteratively by decoupling the two steps. First, we invert for the permittivity only in the minimization of a cost function and second, given the materials, we find the corresponding electric fields through direct solution of the integral equation in the source volume. The sources thus computed are used to generate the far fields and the synthesized triter response. The cost function is obtained by calculating the deviation between the synthesized value of reflectivity/transmittivity and the desired one. Solution geometries for the periodic cell are sought as gratings (ensembles of columns of different heights and widths), or combinations of homogeneous layers of different dielectric materials and gratings. Hence the explicit unknowns of the inversion step are the material permittivities and the relative boundaries separating homogeneous parcels of the periodic cell.

Using Invention to Change How Students Tackle Problems

PubMed Central

Smith, Karen M.; van Stolk, Adrian P.; Spiegelman, George B.

2010-01-01

Invention activities challenge students to tackle problems that superficially appear unrelated to the course material but illustrate underlying fundamental concepts that are fundamental to material that will be presented. During our invention activities in a first-year biology class, students were presented with problems that are parallel to those that living cells must solve, in weekly sessions over a 13-wk term. We compared students who participated in the invention activities sessions with students who participated in sessions of structured problem solving and with students who did not participate in either activity. When faced with developing a solution to a challenging and unfamiliar biology problem, invention activity students were much quicker to engage with the problem and routinely provided multiple reasonable hypotheses. In contrast the other students were significantly slower in beginning to work on the problem and routinely produced relatively few ideas. We suggest that the invention activities develop a highly valuable skill that operates at the initial stages of problem solving. PMID:21123697

Gender and engineering aptitude: Is the color of science, technology, engineering, and math materials related to children's performance?

PubMed

Mulvey, Kelly Lynn; Miller, Bridget; Rizzardi, Victoria

2017-08-01

To investigate gender stereotypes, demonstrated engineering aptitude, and attitudes, children (N=105) solved an engineering problem using either pastel-colored or primary-colored materials. Participants also evaluated the acceptability of denial of access to engineering materials based on gender and counter-stereotypic preferences (i.e., a boy who prefers pastel-colored materials). Whereas material color was not related to differences in female participants' performance, younger boys assigned to pastel materials demonstrated lower engineering aptitude than did other participants. In addition, results documented age- and gender-related differences; younger participants, and sometimes boys, exhibited less flexibility regarding gender stereotypes than did older and female participants. The findings suggest that attempts to enhance STEM (science, technology, engineering, and math) engagement or performance through the color of STEM materials may have unintended consequences. Copyright © 2017 Elsevier Inc. All rights reserved.

Bio-Inspired Functional Surfaces Based on Laser-Induced Periodic Surface Structures

PubMed Central

Müller, Frank A.; Kunz, Clemens; Gräf, Stephan

2016-01-01

Nature developed numerous solutions to solve various technical problems related to material surfaces by combining the physico-chemical properties of a material with periodically aligned micro/nanostructures in a sophisticated manner. The utilization of ultra-short pulsed lasers allows mimicking numerous of these features by generating laser-induced periodic surface structures (LIPSS). In this review paper, we describe the physical background of LIPSS generation as well as the physical principles of surface related phenomena like wettability, reflectivity, and friction. Then we introduce several biological examples including e.g., lotus leafs, springtails, dessert beetles, moth eyes, butterfly wings, weevils, sharks, pangolins, and snakes to illustrate how nature solves technical problems, and we give a comprehensive overview of recent achievements related to the utilization of LIPSS to generate superhydrophobic, anti-reflective, colored, and drag resistant surfaces. Finally, we conclude with some future developments and perspectives related to forthcoming applications of LIPSS-based surfaces. PMID:28773596

Bio-Inspired Functional Surfaces Based on Laser-Induced Periodic Surface Structures.

PubMed

Müller, Frank A; Kunz, Clemens; Gräf, Stephan

2016-06-15

Nature developed numerous solutions to solve various technical problems related to material surfaces by combining the physico-chemical properties of a material with periodically aligned micro/nanostructures in a sophisticated manner. The utilization of ultra-short pulsed lasers allows mimicking numerous of these features by generating laser-induced periodic surface structures (LIPSS). In this review paper, we describe the physical background of LIPSS generation as well as the physical principles of surface related phenomena like wettability, reflectivity, and friction. Then we introduce several biological examples including e.g., lotus leafs, springtails, dessert beetles, moth eyes, butterfly wings, weevils, sharks, pangolins, and snakes to illustrate how nature solves technical problems, and we give a comprehensive overview of recent achievements related to the utilization of LIPSS to generate superhydrophobic, anti-reflective, colored, and drag resistant surfaces. Finally, we conclude with some future developments and perspectives related to forthcoming applications of LIPSS-based surfaces.

An optimization method for the problems of thermal cloaking of material bodies

NASA Astrophysics Data System (ADS)

Alekseev, G. V.; Levin, V. A.

2016-11-01

Inverse heat-transfer problems related to constructing special thermal devices such as cloaking shells, thermal-illusion or thermal-camouflage devices, and heat-flux concentrators are studied. The heatdiffusion equation with a variable heat-conductivity coefficient is used as the initial heat-transfer model. An optimization method is used to reduce the above inverse problems to the respective control problem. The solvability of the above control problem is proved, an optimality system that describes necessary extremum conditions is derived, and a numerical algorithm for solving the control problem is proposed.

Carpet in Schools: Myth and Reality.

ERIC Educational Resources Information Center

Chan, T. C.; Richardson, Michael D.; Jording, Cathy

2001-01-01

Carpet can serve as a type of finish over concrete, improves the acoustical environment, and helps build a more conducive, personalized learning environment. Problems associated with carpeting are related to raw materials, texture, cleaning materials, cost factors, moisture, and alleged contribution to poor indoor air quality. Recommendations are…

An Out-of-Math Experience: Einstein, Relativity, and the Developmental Mathematics Student.

ERIC Educational Resources Information Center

Fiore, Greg

2000-01-01

Discusses Einstein's special relativity theory and some of the developmental mathematics involved. Presents motivational classroom materials used in discussing relative-motion problems, evaluating a radical expression, graphing with asymptotes, interpreting a graph, studying variation, and solving literal and radical equations. (KHR)

Self-Paced Physics, Segments 6-10.

ERIC Educational Resources Information Center

New York Inst. of Tech., Old Westbury.

Five segments of the Self-Paced Physics Course materials are presented in this problems and solutions book for use as the second part of student course work. The subject-matter topics are related to circular motion, work, power, kinetic energy, potential energy, conservative forces, conservation of energy, spring problems, center of mass, and…

BASIC Simulation Programs; Volumes I and II. Biology, Earth Science, Chemistry.

ERIC Educational Resources Information Center

Digital Equipment Corp., Maynard, MA.

Computer programs which teach concepts and processes related to biology, earth science, and chemistry are presented. The seven biology problems deal with aspects of genetics, evolution and natural selection, gametogenesis, enzymes, photosynthesis, and the transport of material across a membrane. Four earth science problems concern climates, the…

Self-Paced Physics, Segments 11-14.

ERIC Educational Resources Information Center

New York Inst. of Tech., Old Westbury.

Four segments of the Self-Paced Physics Course materials are presented in this problems and solutions book for use as the third part of student course work. The subject-matter topics are related to impulses, inelastic and elastic collisions, two-dimensional collision problems, universal constant of gravitation, gravitational acceleration and…

The Management of Online Resources: Problems and Opportunities.

ERIC Educational Resources Information Center

Lewis, D. A.; Adkins, R.

1981-01-01

Describes the management of online information services at ICI Plastics Division in terms of control and development, reviews implications for higher management, and identifies problems and opportunities related to manpower, money, materials, machinery, and time. Project RADIUS (Rapid Access to Data and Information by Untrained Scientists) is also…

Environmental Pollution, Student's Book (Experiences/Experiments/Activities).

ERIC Educational Resources Information Center

Weaver, Elbert C.

Described in this student's manual are numerous experiments to acquaint the learner with community environmental problems. Experiments are relatively simple and useful in the junior high school grades. Activities are provided which emphasize some of the materials involved in pollution problems, such as carbon dioxide, sulfur compounds, and others,…

Crack propagation and arrest in pressurized containers

NASA Technical Reports Server (NTRS)

Erdogan, F.; Delale, F.; Owczarek, J. A.

1976-01-01

The problem of crack propagation and arrest in a finite volume cylindrical container filled with pressurized gas is considered. It is assumed that the cylinder contains a symmetrically located longitudinal part-through crack with a relatively small net ligament. The net ligament suddenly ruptures initiating the process of fracture propagation and depressurization in the cylinder. Thus the problem is a coupled gas dynamics and solid mechanics problem the exact formulation of which does not seem to be possible. The problem is reduced to a proper initial value problem by introducing a dynamic fracture criterion which relates the crack acceleration to the difference between a load factor and the corresponding strength parameter. The results indicate that generally in gas filled cylinders fracture arrest is not possible unless the material behaves in a ductile manner and the container is relatively long.

Boundary shape identification problems in two-dimensional domains related to thermal testing of materials

NASA Technical Reports Server (NTRS)

Banks, H. T.; Kojima, Fumio

1988-01-01

The identification of the geometrical structure of the system boundary for a two-dimensional diffusion system is reported. The domain identification problem treated here is converted into an optimization problem based on a fit-to-data criterion and theoretical convergence results for approximate identification techniques are discussed. Results of numerical experiments to demonstrate the efficacy of the theoretical ideas are reported.

Noise levels, noise annoyance, and hearing-related problems in a dental college.

PubMed

Ahmed, Hafiz Omer; Ali, Wesal Jasim

2017-05-04

Through a cross-sectional survey and integrated sound level meter, this research examined noise exposure and auditory- and nonauditory-related problems experienced by students of a dentistry college located in the United Arab Emirates (UAE). A structured interview questionnaire was used to examine hearing-related problems, noise annoyance, and awareness of 114 students toward noise. The results showed that maximum noise levels were between 65 and 79 dB(A) with peak levels (high and low frequencies) ranging between 89 and 93 dB(A). Around 80% of the students experienced a certain degree of noise annoyance; 54% reported one of the hearing-related problems; and about 10% claimed to have hearing loss to a certain extent. It is recommended that sound-absorbent materials be used during the construction of dental clinics and laboratories to reduce the noise levels.

Sustainability in a materials world

USGS Publications Warehouse

Amey, E.B.; Lemons, J.F.; Berry, Darbi R.

1996-01-01

Many adverse impacts on the environment can be directly related to the materials dispersed to the environment during processing or use, or after use as refuse and waste. Some materials, such as toxic wastes, are a major concern because they create immediate problems with longer-term effects. Gases released by major manufacturing industries can contribute to long-term regional and global problems such as acid rain or increased carbon dioxide in the atmosphere. The use of other materials, however, appears to be more benign or strictly localized in their impacts. If the current per capita level of material consumption in the United States was achieved worldwide, it would create major stresses on both resource adequacy and the environment. In fact, stresses have been created and will continue from this consumption style (developed countries) even if others don't achieve them. ?? 1996 International Association for Mathematical Geology.

"We want the world and we want it now": Materialism, time perspectives and problem spending tendency of Chinese.

PubMed

Ku, Lisbeth; Wu, Anise M S; Lao, Angie K P; Lam, Kerwin I N

2016-10-06

Chinese consumers' spending has been expanding rapidly in the past decade, and along with it household and credit card debt. The present research collected evidence to triangulate the contention that materialism is positively related with Chinese's problem spending tendency (PST), and that present-time-perspective (PTP) and future-time perspectives (FTP) interact systematically with materialism to affect PST. A survey of the general population in Macao, China (Study 1; N = 239) confirmed that materialism was positively correlated with PST. An interaction between materialism and PTP intensified the relationship, whereas an interaction with FTP weakened the relationship. Another survey with a sample of university students (Study 2; N = 223) again found positive relationships among PST, materialism, and PTP, as measured by temporal discount rate. But further exploration showed that PST was only related with temporal discounting among high materialists, but not among low materialists. Study 3 experimentally examined the causal effects of materialism and FTP on PST. When being primed of an orientation towards materialism (n = 33), the participants' planned consumption doubled that of the control group (n = 31). A FTP prime interacted with materialism prime and put a "damper" on participants' planned spending (n = 29), compared to their counterparts who were not primed of such a time perspective. © 2016 International Union of Psychological Science.

Plastics in Perspective.

ERIC Educational Resources Information Center

Bergandine, David R.; Holm, D. Andrew

The materials in this curriculum supplement, developed for middle school or high school science classes, present solid waste problems related to plastics. The set of curriculum materials is divided into two units to be used together or independently. Unit I begins by comparing patterns in solid waste from 1960 to 1990 and introducing methods for…

Wood for structural and architectural purposes

Treesearch

C.W. Boyd; P. Koch; H.B. MeKean; C.R. Morschauser; S.B. Preston; F.F. Wangaard

1976-01-01

In recent years major emphasis has been placed on nonrenewable resources in relation to potential national problems that may arise from possible changes in materials supply or utilization. Renewable resources, however, have received disproportionately small attention in spite of their current importance as industrial raw materials and their potential for the future. In...

Millwright Apprenticeship. Related Training Modules. 6.1-6.12 Human Relations.

ERIC Educational Resources Information Center

Lane Community Coll., Eugene, OR.

This packet, part of the instructional materials for the Oregon apprenticeship program for millwright training, contains 12 modules covering human relations. The modules provide information on the following topics: communications skills, feedback, individual strengths, interpersonal conflicts, group problem solving, goal setting and decision…

Variational and numerical analysis of a quasistatic viscoelastic problem with normal compliance, friction and damage

NASA Astrophysics Data System (ADS)

Han, Weimin; Shillor, Meir; Sofonea, Mircea

2001-12-01

We consider a model for quasistatic frictional contact between a viscoelastic body and a foundation. The material constitutive relation is assumed to be nonlinear. The mechanical damage of the material, caused by excessive stress or strain, is described by the damage function, the evolution of which is determined by a parabolic inclusion. The contact is modeled with the normal compliance condition and the associated version of Coulomb's law of dry friction. We derive a variational formulation for the problem and prove the existence of its unique weak solution. We then study a fully discrete scheme for the numerical solutions of the problem and obtain error estimates on the approximate solutions.

Failure evolution in granular material retained by rigid wall in active mode

NASA Astrophysics Data System (ADS)

Pietrzak, Magdalena; Leśniewska, Danuta

2012-10-01

This paper presents a detailed study of a selected small scale model test, performed on a sample of surrogate granular material, retained by a rigid wall (typical geotechnical problem of earth thrust on a retaining wall). The experimental data presented in this paper show that the deformation of granular sample behind retaining wall can undergo some cyclic changes. The nature of these cycles is not clear - it is probably related to some micromechanical features of granular materials, which are recently extensively studied in many research centers in the world. Employing very precise DIC (PIV) method can help to relate micro and macro-scale behavior of granular materials.

A Bibliography on Police and Community Relations.

ERIC Educational Resources Information Center

Miller, Martin G., Comp.

A reflection of concerns of social scientists and of those involved in law enforcement, this extensive bibliography on police and community relations covers general material (including historical reviews); problems and approaches in police administration; the police image and community relations; the impact of the civil rights movement and civil…

Importance biasing scheme implemented in the PRIZMA code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kandiev, I.Z.; Malyshkin, G.N.

1997-12-31

PRIZMA code is intended for Monte Carlo calculations of linear radiation transport problems. The code has wide capabilities to describe geometry, sources, material composition, and to obtain parameters specified by user. There is a capability to calculate path of particle cascade (including neutrons, photons, electrons, positrons and heavy charged particles) taking into account possible transmutations. Importance biasing scheme was implemented to solve the problems which require calculation of functionals related to small probabilities (for example, problems of protection against radiation, problems of detection, etc.). The scheme enables to adapt trajectory building algorithm to problem peculiarities.

What's all the Fuss about Mercury?

ERIC Educational Resources Information Center

Roy, Ken

2004-01-01

Mercury tends to vaporize when exposed to air. The warmer the air, the more quickly it vaporizes. Although swallowing mercury can be a problem, the greater risk results from inhalation and skin absorption. Symptoms and health-related problems can result within hours of exposure. Spilled mercury settles in cracks and absorbent material such as…

Instance-Based Ontology Matching for Open and Distance Learning Materials

ERIC Educational Resources Information Center

Cerón-Figueroa, Sergio; López-Yáñez, Itzamá; Villuendas-Rey, Yenny; Camacho-Nieto, Oscar; Aldape-Pérez, Mario; Yáñez-Márquez, Cornelio

2017-01-01

The present work describes an original associative model of pattern classification and its application to align different ontologies containing Learning Objects (LOs), which are in turn related to Open and Distance Learning (ODL) educative content. The problem of aligning ontologies is known as Ontology Matching Problem (OMP), whose solution is…

Simulator test to study hot-flow problems related to a gas cooled reactor

NASA Technical Reports Server (NTRS)

Poole, J. W.; Freeman, M. P.; Doak, K. W.; Thorpe, M. L.

1973-01-01

An advance study of materials, fuel injection, and hot flow problems related to the gas core nuclear rocket is reported. The first task was to test a previously constructed induction heated plasma GCNR simulator above 300 kW. A number of tests are reported operating in the range of 300 kW at 10,000 cps. A second simulator was designed but not constructed for cold-hot visualization studies using louvered walls. A third task was a paper investigation of practical uranium feed systems, including a detailed discussion of related problems. The last assignment resulted in two designs for plasma nozzle test devices that could be operated at 200 atm on hydrogen.

Communication Skills for OMRDD Direct Care Workers: Distance Learning Study Guide.

ERIC Educational Resources Information Center

Denny, Verna Haskins

This self-directed, self-paced adult distance education program provides developmental aides and transitional employees with practice in job-related reading, writing, math, and problem solving. Participants use e-mail, print materials, and videotapes to do assignments. An introductory brochure precedes materials for 12 theme areas and 105 units…

Environmental radiation and the lung

PubMed Central

Hamrick, Philip E.; Walsh, Phillip J.

1974-01-01

Environmental sources of radioactive materials and their relation to lung doses and lung burdens are described. The approaches used and the problems encountered in estimating lung doses are illustrated. Exposure to radon daughter products is contrasted to exposure to plutonium as particular examples of the hazards associated with radioactive materials of different chemical and physical characteristics. PMID:4620334

Teaching about Hazardous Materials. ERIC/SMEAC Environmental Education Digest No. 2.

ERIC Educational Resources Information Center

Disinger, John F.

Problems related to the handling of hazardous substances and toxic wastes have escalated making this environmental dilemma a national concern. This digest provides an update of key legislative and management efforts associated with hazardous wastes and reviews current instructional materials in the area. Major topics addressed include: (1) waste…

Materials Science Laboratory

NASA Technical Reports Server (NTRS)

Jackson, Dionne

2005-01-01

The NASA Materials Science Laboratory (MSL) provides science and engineering services to NASA and Contractor customers at KSC, including those working for the Space Shuttle. International Space Station. and Launch Services Programs. These services include: (1) Independent/unbiased failure analysis (2) Support to Accident/Mishap Investigation Boards (3) Materials testing and evaluation (4) Materials and Processes (M&P) engineering consultation (5) Metrology (6) Chemical analysis (including ID of unknown materials) (7) Mechanical design and fabrication We provide unique solutions to unusual and urgent problems associated with aerospace flight hardware, ground support equipment and related facilities.

The Online Catalog: Exceeding Our Grasp.

ERIC Educational Resources Information Center

Lipow, Anne Grodzins

1989-01-01

Discusses two problems related to the use of online catalogs: (1) staff training has not kept pace with new catalogs, resulting in a lack of search expertise in staff and patrons; and (2) users expect instant access to materials found in the catalog. It is argued that these problems must be addressed to adequately serve library patrons. (CLB)

Timoshenko beam model for chiral materials

NASA Astrophysics Data System (ADS)

Ma, T. Y.; Wang, Y. N.; Yuan, L.; Wang, J. S.; Qin, Q. H.

2017-12-01

Natural and artificial chiral materials such as deoxyribonucleic acid (DNA), chromatin fibers, flagellar filaments, chiral nanotubes, and chiral lattice materials widely exist. Due to the chirality of intricately helical or twisted microstructures, such materials hold great promise for use in diverse applications in smart sensors and actuators, force probes in biomedical engineering, structural elements for absorption of microwaves and elastic waves, etc. In this paper, a Timoshenko beam model for chiral materials is developed based on noncentrosymmetric micropolar elasticity theory. The governing equations and boundary conditions for a chiral beam problem are derived using the variational method and Hamilton's principle. The static bending and free vibration problem of a chiral beam are investigated using the proposed model. It is found that chirality can significantly affect the mechanical behavior of beams, making materials more flexible compared with nonchiral counterparts, inducing coupled twisting deformation, relatively larger deflection, and lower natural frequency. This study is helpful not only for understanding the mechanical behavior of chiral materials such as DNA and chromatin fibers and characterizing their mechanical properties, but also for the design of hierarchically structured chiral materials.

Timoshenko beam model for chiral materials

NASA Astrophysics Data System (ADS)

Ma, T. Y.; Wang, Y. N.; Yuan, L.; Wang, J. S.; Qin, Q. H.

2018-06-01

Natural and artificial chiral materials such as deoxyribonucleic acid (DNA), chromatin fibers, flagellar filaments, chiral nanotubes, and chiral lattice materials widely exist. Due to the chirality of intricately helical or twisted microstructures, such materials hold great promise for use in diverse applications in smart sensors and actuators, force probes in biomedical engineering, structural elements for absorption of microwaves and elastic waves, etc. In this paper, a Timoshenko beam model for chiral materials is developed based on noncentrosymmetric micropolar elasticity theory. The governing equations and boundary conditions for a chiral beam problem are derived using the variational method and Hamilton's principle. The static bending and free vibration problem of a chiral beam are investigated using the proposed model. It is found that chirality can significantly affect the mechanical behavior of beams, making materials more flexible compared with nonchiral counterparts, inducing coupled twisting deformation, relatively larger deflection, and lower natural frequency. This study is helpful not only for understanding the mechanical behavior of chiral materials such as DNA and chromatin fibers and characterizing their mechanical properties, but also for the design of hierarchically structured chiral materials.

Proceedings of the NASA Conference on Materials for Improved Fire Safety

NASA Technical Reports Server (NTRS)

1970-01-01

The Manned Spacecraft Center was pleased to host the NASA Conference on Materials for Improved Fire Safety which was held on May 6 and 7, 1970. This document is a compilation of papers presented at the conference and represents the culmination of several years of effort by NASA and industry which was directed toward the common objective of minimizing the fire hazard in manned spacecraft and in some other related areas. One of the more serious problem areas in the Apollo program was the flammability of nonmetallic materials. The effective and timely solution of this problem area resulted from much of the effort reported herein and contributed greatly toward the successful achievement of landing men on the moon and returning them safely to earth.

Modeling the behaviour of shape memory materials under large deformations

NASA Astrophysics Data System (ADS)

Rogovoy, A. A.; Stolbova, O. S.

2017-06-01

In this study, the models describing the behavior of shape memory alloys, ferromagnetic materials and polymers have been constructed, using a formalized approach to develop the constitutive equations for complex media under large deformations. The kinematic and constitutive equations, satisfying the principles of thermodynamics and objectivity, have been derived. The application of the Galerkin procedure to the systems of equations of solid mechanics allowed us to obtain the Lagrange variational equation and variational formulation of the magnetostatics problems. These relations have been tested in the context of the problems of finite deformation in shape memory alloys and ferromagnetic materials during forward and reverse martensitic transformations and in shape memory polymers during forward and reverse relaxation transitions from a highly elastic to a glassy state.

On the finite length-scale of compressible shock-waves formed in free-surface flows of dry granular materials down a slope

NASA Astrophysics Data System (ADS)

Faug, Thierry

2017-04-01

The Rankine-Hugoniot jump conditions traditionally describe the theoretical relationship between the equilibrium state on both sides of a shock-wave. They are based on the crucial assumption that the length-scale needed to adjust the equilibrium state upstream of the shock to downstream of it is too small to be of significance to the problem. They are often used with success to describe the shock-waves in a number of applications found in both fluid and solid mechanics. However, the relations based on jump conditions at singular surfaces may fail to capture some features of the shock-waves formed in complex materials, such as granular matter. This study addresses the particular problem of compressible shock-waves formed in flows of dry granular materials down a slope. This problem is for instance relevant to full-scale geophysical granular flows in interaction with natural obstacles or man-made structures, such as topographical obstacles or mitigation dams respectively. Steady-state jumps formed in granular flows and travelling shock-waves produced at the impact of a granular avalanche-flow with a rigid wall are considered. For both situations, new analytical relations which do not consider that the granular shock-wave shrinks into a singular surface are derived, by using balance equations in their depth-averaged forms for mass and momentum. However, these relations need additional inputs that are closure relations for the size and the shape of the shock-wave, and a relevant constitutive friction law. Small-scale laboratory tests and numerical simulations based on the discrete element method are shortly presented and used to infer crucial information needed for the closure relations. This allows testing some predictive aspects of the simple analytical approach proposed for both steady-state and travelling shock-waves formed in free-surface flows of dry granular materials down a slope.

Against Laplacian Reduction of Newtonian Mass to Spatiotemporal Quantities

NASA Astrophysics Data System (ADS)

Martens, Niels C. M.

2018-05-01

Laplace wondered about the minimal choice of initial variables and parameters corresponding to a well-posed initial value problem. Discussions of Laplace's problem in the literature have focused on choosing between spatiotemporal variables relative to absolute space (i.e. substantivalism) or merely relative to other material bodies (i.e. relationalism) and between absolute masses (i.e. absolutism) or merely mass ratios (i.e. comparativism). This paper extends these discussions of Laplace's problem, in the context of Newtonian Gravity, by asking whether mass needs to be included in the initial state at all, or whether a purely spatiotemporal initial state suffices. It is argued that mass indeed needs to be included; removing mass from the initial state drastically reduces the predictive and explanatory power of Newtonian Gravity.

Against Laplacian Reduction of Newtonian Mass to Spatiotemporal Quantities

NASA Astrophysics Data System (ADS)

Martens, Niels C. M.

2018-03-01

Laplace wondered about the minimal choice of initial variables and parameters corresponding to a well-posed initial value problem. Discussions of Laplace's problem in the literature have focused on choosing between spatiotemporal variables relative to absolute space (i.e. substantivalism) or merely relative to other material bodies (i.e. relationalism) and between absolute masses (i.e. absolutism) or merely mass ratios (i.e. comparativism). This paper extends these discussions of Laplace's problem, in the context of Newtonian Gravity, by asking whether mass needs to be included in the initial state at all, or whether a purely spatiotemporal initial state suffices. It is argued that mass indeed needs to be included; removing mass from the initial state drastically reduces the predictive and explanatory power of Newtonian Gravity.

Improving Student Science Achievement in Grades 4-6 through Hands-On Materials and Concept Verbalization.

ERIC Educational Resources Information Center

Brooks, Roger C.

This report describes a program designed to improve science achievement among students in grades 4-6 in a New Hampshire school. The areas of improvement included physical, earth, and life sciences. Analysis of the problem indicated a need for improved teaching techniques and for additional materials related to the instructional strategies. The…

Study of multiple hologram recording in lithium niobate

NASA Technical Reports Server (NTRS)

Gaylord, T. K.; Callen, W. R.

1974-01-01

The results of detailed experimental and theoretical considerations relating to multiple hologram recording in lithium niobate are reported. The following problem areas are identified and discussed: (1) the angular selectivity of the stored holograms, (2) interference effects due to the crystal surfaces, (3) beam divergence effects, (4) material recording sensitivity, and (5) scattered light from material inhomogeneities.

Cultural Materialism and Behavior Analysis: Common Problems and Radical Solutions

ERIC Educational Resources Information Center

Harris, Marvin

2007-01-01

This article presents a transcribed audio recording of the invited address the author gave to Sigrid Glenn on the relations between cultural materialism and radical behaviorism at the 12th annual conference of the Association for Behavior Analysis in Milwaukee, Wisconsin on May 23rd, 1986. In his address, the author emphasizes that the necessity…

ASSESSMENTS OF FUTURE ENVIRONMENTAL TRENDS AND PROBLEMS OF INCREASED USE, RECYCLING, AND COMBUSTION OF FIBER-REINFORCED, PLASTIC AND METAL COMPOSITE MATERIALS

EPA Science Inventory

The purpose of the study is to identify and define future environmental concerns related to the projected utilization, recycling, and combustion of composite materials. The study is being conducted for the Office of Strategic Assessment and Special Studies (OSASS) of the U.S. Env...

Biological Science: An Ecological Approach. BSCS Green Version. Teacher's Resource Book and Test Item Bank. Sixth Edition.

ERIC Educational Resources Information Center

Biological Sciences Curriculum Study, Colorado Springs.

This book consists of four sections: (1) "Supplemental Materials"; (2) "Supplemental Investigations"; (3) "Test Item Bank"; and (4) "Blackline Masters." The first section provides additional background material related to selected chapters and investigations in the student book. Included are a periodic table of the elements, genetics problems and…

Common problems and pitfalls in gear design

NASA Technical Reports Server (NTRS)

Townsend, Dennis P.

1986-01-01

There are several pitfalls and problems associated with the successful design of a new gear transmission. A new design will require the knowledge and experience of several technical areas of engineering. Most of the pitfalls and problems associated with a new design are related to an inadequate evaluation of several areas, such as, the lubrication and cooling requirements, complete static and dynamic load analysis, evaluation of materials and heat treatment and the latest manufacturing technology. Some of the common problems of the gear design process are discussed with recommendations made for avoiding these conditions.

Inorganic Photovoltaics Materials and Devices: Past, Present, and Future

NASA Technical Reports Server (NTRS)

Hepp, Aloysius F.; Bailey, Sheila G.; Rafaelle, Ryne P.

2005-01-01

This report describes recent aspects of advanced inorganic materials for photovoltaics or solar cell applications. Specific materials examined will be high-efficiency silicon, gallium arsenide and related materials, and thin-film materials, particularly amorphous silicon and (polycrystalline) copper indium selenide. Some of the advanced concepts discussed include multi-junction III-V (and thin-film) devices, utilization of nanotechnology, specifically quantum dots, low-temperature chemical processing, polymer substrates for lightweight and low-cost solar arrays, concentrator cells, and integrated power devices. While many of these technologies will eventually be used for utility and consumer applications, their genesis can be traced back to challenging problems related to power generation for aerospace and defense. Because this overview of inorganic materials is included in a monogram focused on organic photovoltaics, fundamental issues and metrics common to all solar cell devices (and arrays) will be addressed.

Carbonaceous electrode materials for supercapacitors.

PubMed

Hao, Long; Li, Xianglong; Zhi, Linjie

2013-07-26

Supercapacitors have been widely studied around the world in recent years, due to their excellent power density and long cycle life. As the most frequently used electrode materials for supercapacitors, carbonaceous materials attract more and more attention. However, their relatively low energy density still holds back the widespread application. Up to now, various strategies have been developed to figure out this problem. This research news summarizes the recent advances in improving the supercapacitor performance of carbonaceous materials, including the incorporation of heteroatoms and the pore size effect (subnanopores' contribution). In addition, a new class of carbonaceous materials, porous organic networks (PONs) has been managed into the supercapacitor field, which promises great potential in not only improving the supercapacitor performances, but also unraveling the related mechanisms. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

What causes addiction problems? Environmental, biological and constitutional explanations in press portrayals from four European welfare societies.

PubMed

Hellman, Matilda; Majamäki, Maija; Rolando, Sara; Bujalski, Michał; Lemmens, Paul

2015-03-01

Press items (N = 1327) about addiction related problems were collected from politically independent daily newspapers in Finland, Italy, the Netherlands, and Poland from 1991, 1998, and 2011. A synchronized qualitative coding was performed for discerning the descriptions of the genesis to the problems in terms of described causes to and reasons for why they occur. Environmental explanations were by far the most common and they varied most between the materials. The analysis documents how the portrayals include traces of their contextual origin, relating to different media tasks and welfare cultural traditions. Meaning-based differences were also assigned to the kind of problems that held the most salience in the press reporting. A general worry over societal change is tied into the explanations of accumulating addiction problems and underpins the press reporting in all countries.

[Biomedical foundation for human safety in aviation].

PubMed

Ushakov, I B

2004-01-01

According to the author, preventive medical issues of providing human safety in aviation are related to the fundamental biomedical and socio-psychological problems of human beings in the present-day world. Factual material for analysis was compiled in the study performed at the State Research and Test Institute of Military Medicine. Outlined are main vectors of the future attack on the problem.

Resource Management Resource Guide. A Resource for Teaching the Resource Management Core Course Area of Ohio's Work and Family Life Program.

ERIC Educational Resources Information Center

Kister, Joanna; And Others

This Resource Management Resource Guide is intended to help teachers implement Ohio's Work and Family Life Program. Course content focuses on the practical problems related to managing human and material resources, making consumer decisions, and feeding, clothing, and housing the family. These practical problems are posed through case studies and…

Review of Recent Literature on Figure Drawing Tests as Related to Research Problems in Art Education

ERIC Educational Resources Information Center

McWhinnie, Harold J.

1971-01-01

McFee's perception-delineation theory is supported. Major methodological problems of the psychological research presented are in the area of set and the control of specific art materials. Among the conclusions: figure drawing may not be culture fair; a person trained in visual arts should be employed in research using figure drawing tests. (VW)

An Interactive Videodisc Program To Evaluate and Train Job-Related Math Skills for Transition. Final Report.

ERIC Educational Resources Information Center

Harris, Carolyn DeMeyer; And Others

The project designed and developed a videodisc package that provides both assessment and related instruction programs for job-related mathematics problem solving, using simulations to provide direct access to vocational situations. The materials are intended to meet the needs of youth and young adults with mild mental handicaps in transition from…

Problem-based learning on quantitative analytical chemistry course

NASA Astrophysics Data System (ADS)

Fitri, Noor

2017-12-01

This research applies problem-based learning method on chemical quantitative analytical chemistry, so called as "Analytical Chemistry II" course, especially related to essential oil analysis. The learning outcomes of this course include aspects of understanding of lectures, the skills of applying course materials, and the ability to identify, formulate and solve chemical analysis problems. The role of study groups is quite important in improving students' learning ability and in completing independent tasks and group tasks. Thus, students are not only aware of the basic concepts of Analytical Chemistry II, but also able to understand and apply analytical concepts that have been studied to solve given analytical chemistry problems, and have the attitude and ability to work together to solve the problems. Based on the learning outcome, it can be concluded that the problem-based learning method in Analytical Chemistry II course has been proven to improve students' knowledge, skill, ability and attitude. Students are not only skilled at solving problems in analytical chemistry especially in essential oil analysis in accordance with local genius of Chemistry Department, Universitas Islam Indonesia, but also have skilled work with computer program and able to understand material and problem in English.

Pain-related and Psychological Symptoms in Adolescents With Musculoskeletal and Sleep Problems

PubMed Central

Wilson, Sue; Munafò, Marcus R.

2016-01-01

Objectives: Two-thirds of adolescents with chronic musculoskeletal pain report a concurrent sleep problem. Both musculoskeletal pain and sleep problems can have deleterious effects on physiological and psychological well-being. We explored the prevalence of sleep problems and musculoskeletal pain, using data on 3568 adolescents from the Avon Longitudinal Study of Children. Materials and Methods: A comprehensive battery of questionnaires was administered to derive clinical phenotypes of musculoskeletal pain. Adolescents with single symptoms were compared with those reporting both musculoskeletal pain and sleep problems. Linear and logistic regression analyses were used to compare groups on pain-related variables and psychological complaints. The association between sociodemographic variables and comorbid musculoskeletal pain and sleep problems was assessed using logistic regression. Results: Over half the sample was female (n=2076, 58.2%) and the majority of European ancestry (n=3174, 97.7%). Only 5.5% (n=196) of participants were identified as having a pain condition, while 21.2% (n=749) reported a significant sleep problem, and 2.8% (n=99) reported comorbid musculoskeletal pain and sleep problems. Adolescents with comorbid problems experienced greater pain intensity and pain-related anxiety. Other psychological complaints were also higher in those who experienced concurrent problems, including depression, fatigue, concentration, and overall severity of psychological symptoms. Discussion: Comorbid sleep and pain problems were associated with a higher incidence of pain-related and psychological symptoms. Sleep problems may therefore be an important modifiable risk factor for alleviating distress in adolescents with musculoskeletal pain. PMID:25974623

The materials processing research base of the Materials Processing Center. Report for FY 1982

NASA Technical Reports Server (NTRS)

Flemings, M. C.

1983-01-01

The work described, while involving research in the broad field of materials processing, has two common features: the problems are closed related to space precessing of materials and have both practical and fundamental significance. An interesting and important feature of many of the projects is that the interdisciplinary nature of the problem mandates complementary analytical modeling/experimental approaches. An other important aspect of many of the projects is the increasing use of mathematical modeling techniques as one of the research tools. The predictive capability of these models, when tested against measurements, plays a very important role in both the planning of experimental programs and in the rational interpretation of the results. Many of the projects described have a space experiment as their ultimate objective. Mathematical models are proving to be extremely valuable in projecting the findings of ground - based experiments to microgravity conditions.

Teaching the Black Experience.

ERIC Educational Resources Information Center

Kirschenbaum, Howard

1968-01-01

Instructional materials and teaching approaches can be used to get students to seriously and constructively confront problems in race relations which they will eventually have to solve. For example, Richard Wright's "Black Boy," an anthology of Negro poetry or a collection of poems on race relations, and such films as "Where is Prejudice?" can…

Overview of NORM and activities by a NORM licensed permanent decontamination and waste processing facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mirro, G.A.

1997-02-01

This paper presents an overview of issues related to handling NORM materials, and provides a description of a facility designed for the processing of NORM contaminated equipment. With regard to handling NORM materials the author discusses sources of NORM, problems, regulations and disposal options, potential hazards, safety equipment, and issues related to personnel protection. For the facility, the author discusses: description of the permanent facility; the operations of the facility; the license it has for handling specific radioactive material; operating and safety procedures; decontamination facilities on site; NORM waste processing capabilities; and offsite NORM services which are available.

Critical time for acoustic wavesin weakly nonlinear poroelastic materials

NASA Astrophysics Data System (ADS)

Wilmanski, K.

2005-05-01

The final time of existence (critical time) of acoustic waves is a characteristic feature of nonlinear hyperbolic models. We consider such a problem for poroelastic saurated materials of which the material properties are described by Signorini-type constitutitve relations for stresses in the skeleton, and whose material parameters depend on the current porosity. In the one-dimensional case under consideration, the governing set of equations describes changes of extension of the skeleton, a mass density of the fluid, partial velocities of the skeleton and of the fluid and a porosity. We rely on a second order approximation. Relations of the critical time to an initial porosity and to an initial amplitude are discussed. The connection to the threshold of liquefaction is indicated.

Roofing research: a bibliography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robinson, J.N.; Nichols, C.L.

1981-04-01

A listing, indexed by subject, primary author, and secondary authors, is presented of some 530 references in the literature related to roofing research - materials, construction, and in-service problems. Structural design of roofing systems is not covered.

O-atom degradation mechanisms of materials

NASA Technical Reports Server (NTRS)

Coulter, Daniel R.; Liang, Ranty H.; Chung, Shirley Y.; Smith, Keri Oda; Gupta, Amitava

1987-01-01

The low Earth orbit environment is described and the critical issues relating to oxygen atom degradation are discussed. Some analytic techniques for studying the problem and preliminary results on the underlying degradation mechanisms are presented.

Cracking of coated materials under transient thermal stresses

NASA Technical Reports Server (NTRS)

Rizk, A. A.; Erdogan, Fazil

1988-01-01

The crack problem for a relatively thin layer bonded to a very thick substrate under thermal shock conditions is considered. The effect of surface cooling rate is studied by assuming the temperature boundary condition to be a ramp function. Among the crack geometries considered are the edge crack in the coating layer, the broken layer, the edge crack going through the interface, the undercoat crack in the substrate and the embedded crack crossing the interface. The primary calculated quantity is the stress intensity factor at various singular points and the main variables are the relative sizes and locations of cracks, the time, and the duration of the cooling ramp. The problem is solved and rather extensive results are given for two material pairs, namely a stainless steel layer welded on a ferritic medium and a ceramic coating on a steel substrate.

Cracking of coated materials under transient thermal stresses

NASA Technical Reports Server (NTRS)

Rizk, A. A.; Erdogan, F.

1989-01-01

The crack problem for a relatively thin layer bonded to a very thick substrate under thermal shock conditions is considered. The effect of surface cooling rate is studied by assuming the temperature boundary condition to be a ramp function. Among the crack geometries considered are the edge crack in the coating layer, the broken layer, the edge crack going through the interface, the undercoat crack in the substrate and the embedded crack crossing the interface. The primary calculated quantity is the stress intensity factor at various singular points and the main variables are the relative sizes and locations of cracks, the time, and the duration of the cooling ramp. The problem is solved and rather extensive results are given for two material pairs, namely a stainless steel layer welded on a ferritic medium and a ceramic coating on a steel substrate.

MO-F-204-00: Preparing for the ABR Diagnostic and Nuclear Medical Physics Exams

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

Adequate, efficient preparation for the ABR Diagnostic and Nuclear Medical Physics exams is key to successfully obtain ABR certification. Each part of the ABR exam presents its own challenges: Part I: Determine the scope of basic medical physics study material, efficiently review this material, and solve related written questions/problems. Part II: Understand imaging principles, modalities, and systems, including image acquisition, processing, and display. Understand the relationship between imaging techniques, image quality, patient dose and safety, and solve related written questions/problems. Part III: Gain crucial, practical, clinical medical physics experience. Effectively communicate and explain the practice, performance, and significance of allmore » aspects of clinical medical physics. All parts of the ABR exam require specific skill sets and preparation: mastery of basic physics and imaging principles; written problem solving often involving rapid calculation; responding clearly and succinctly to oral questions about the practice, methods, and significance of clinical medical physics. This symposium focuses on the preparation necessary for each part of the ABR exam. Although there is some overlap, the nuclear exam covers a different body of knowledge than the diagnostic exam. A separate speaker will address those unique aspects of the nuclear exam, and how preparing for a second specialty differs from the first. Medical physicists who recently completed each ABR exam portion will share their experiences, insights, and preparation methods to help attendees best prepare for the challenges of each part of the ABR exam. In accordance with ABR exam security policy, no recalls or exam questions will be discussed. Learning Objectives: How to prepare for Part 1 of the ABR exam by determining the scope of basic medical physics study material and related problem solving/calculations How to prepare for Part 2 of the ABR exam by understanding diagnostic and/or nuclear imaging physics, systems, dosimetry, safety and related problem solving/calculations How to prepare for Part 3 of the ABR exam by effectively communicating the practice, methods, and significance of clinical diagnostic and/or nuclear medical physics.« less

MO-F-204-02: Preparing for Part 2 of the ABR Diagnostic Physics Exam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szczykutowicz, T.

Adequate, efficient preparation for the ABR Diagnostic and Nuclear Medical Physics exams is key to successfully obtain ABR certification. Each part of the ABR exam presents its own challenges: Part I: Determine the scope of basic medical physics study material, efficiently review this material, and solve related written questions/problems. Part II: Understand imaging principles, modalities, and systems, including image acquisition, processing, and display. Understand the relationship between imaging techniques, image quality, patient dose and safety, and solve related written questions/problems. Part III: Gain crucial, practical, clinical medical physics experience. Effectively communicate and explain the practice, performance, and significance of allmore » aspects of clinical medical physics. All parts of the ABR exam require specific skill sets and preparation: mastery of basic physics and imaging principles; written problem solving often involving rapid calculation; responding clearly and succinctly to oral questions about the practice, methods, and significance of clinical medical physics. This symposium focuses on the preparation necessary for each part of the ABR exam. Although there is some overlap, the nuclear exam covers a different body of knowledge than the diagnostic exam. A separate speaker will address those unique aspects of the nuclear exam, and how preparing for a second specialty differs from the first. Medical physicists who recently completed each ABR exam portion will share their experiences, insights, and preparation methods to help attendees best prepare for the challenges of each part of the ABR exam. In accordance with ABR exam security policy, no recalls or exam questions will be discussed. Learning Objectives: How to prepare for Part 1 of the ABR exam by determining the scope of basic medical physics study material and related problem solving/calculations How to prepare for Part 2 of the ABR exam by understanding diagnostic and/or nuclear imaging physics, systems, dosimetry, safety and related problem solving/calculations How to prepare for Part 3 of the ABR exam by effectively communicating the practice, methods, and significance of clinical diagnostic and/or nuclear medical physics.« less

MO-F-204-03: Preparing for Part 3 of the ABR Diagnostic Physics Exam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zambelli, J.

Adequate, efficient preparation for the ABR Diagnostic and Nuclear Medical Physics exams is key to successfully obtain ABR certification. Each part of the ABR exam presents its own challenges: Part I: Determine the scope of basic medical physics study material, efficiently review this material, and solve related written questions/problems. Part II: Understand imaging principles, modalities, and systems, including image acquisition, processing, and display. Understand the relationship between imaging techniques, image quality, patient dose and safety, and solve related written questions/problems. Part III: Gain crucial, practical, clinical medical physics experience. Effectively communicate and explain the practice, performance, and significance of allmore » aspects of clinical medical physics. All parts of the ABR exam require specific skill sets and preparation: mastery of basic physics and imaging principles; written problem solving often involving rapid calculation; responding clearly and succinctly to oral questions about the practice, methods, and significance of clinical medical physics. This symposium focuses on the preparation necessary for each part of the ABR exam. Although there is some overlap, the nuclear exam covers a different body of knowledge than the diagnostic exam. A separate speaker will address those unique aspects of the nuclear exam, and how preparing for a second specialty differs from the first. Medical physicists who recently completed each ABR exam portion will share their experiences, insights, and preparation methods to help attendees best prepare for the challenges of each part of the ABR exam. In accordance with ABR exam security policy, no recalls or exam questions will be discussed. Learning Objectives: How to prepare for Part 1 of the ABR exam by determining the scope of basic medical physics study material and related problem solving/calculations How to prepare for Part 2 of the ABR exam by understanding diagnostic and/or nuclear imaging physics, systems, dosimetry, safety and related problem solving/calculations How to prepare for Part 3 of the ABR exam by effectively communicating the practice, methods, and significance of clinical diagnostic and/or nuclear medical physics.« less

MO-F-204-01: Preparing for Part 1 of the ABR Diagnostic Physics Exam

DOE Office of Scientific and Technical Information (OSTI.GOV)

McKenney, S.

Adequate, efficient preparation for the ABR Diagnostic and Nuclear Medical Physics exams is key to successfully obtain ABR certification. Each part of the ABR exam presents its own challenges: Part I: Determine the scope of basic medical physics study material, efficiently review this material, and solve related written questions/problems. Part II: Understand imaging principles, modalities, and systems, including image acquisition, processing, and display. Understand the relationship between imaging techniques, image quality, patient dose and safety, and solve related written questions/problems. Part III: Gain crucial, practical, clinical medical physics experience. Effectively communicate and explain the practice, performance, and significance of allmore » aspects of clinical medical physics. All parts of the ABR exam require specific skill sets and preparation: mastery of basic physics and imaging principles; written problem solving often involving rapid calculation; responding clearly and succinctly to oral questions about the practice, methods, and significance of clinical medical physics. This symposium focuses on the preparation necessary for each part of the ABR exam. Although there is some overlap, the nuclear exam covers a different body of knowledge than the diagnostic exam. A separate speaker will address those unique aspects of the nuclear exam, and how preparing for a second specialty differs from the first. Medical physicists who recently completed each ABR exam portion will share their experiences, insights, and preparation methods to help attendees best prepare for the challenges of each part of the ABR exam. In accordance with ABR exam security policy, no recalls or exam questions will be discussed. Learning Objectives: How to prepare for Part 1 of the ABR exam by determining the scope of basic medical physics study material and related problem solving/calculations How to prepare for Part 2 of the ABR exam by understanding diagnostic and/or nuclear imaging physics, systems, dosimetry, safety and related problem solving/calculations How to prepare for Part 3 of the ABR exam by effectively communicating the practice, methods, and significance of clinical diagnostic and/or nuclear medical physics.« less

MO-F-204-04: Preparing for Parts 2 & 3 of the ABR Nuclear Medicine Physics Exam

DOE Office of Scientific and Technical Information (OSTI.GOV)

MacDougall, R.

Adequate, efficient preparation for the ABR Diagnostic and Nuclear Medical Physics exams is key to successfully obtain ABR certification. Each part of the ABR exam presents its own challenges: Part I: Determine the scope of basic medical physics study material, efficiently review this material, and solve related written questions/problems. Part II: Understand imaging principles, modalities, and systems, including image acquisition, processing, and display. Understand the relationship between imaging techniques, image quality, patient dose and safety, and solve related written questions/problems. Part III: Gain crucial, practical, clinical medical physics experience. Effectively communicate and explain the practice, performance, and significance of allmore » aspects of clinical medical physics. All parts of the ABR exam require specific skill sets and preparation: mastery of basic physics and imaging principles; written problem solving often involving rapid calculation; responding clearly and succinctly to oral questions about the practice, methods, and significance of clinical medical physics. This symposium focuses on the preparation necessary for each part of the ABR exam. Although there is some overlap, the nuclear exam covers a different body of knowledge than the diagnostic exam. A separate speaker will address those unique aspects of the nuclear exam, and how preparing for a second specialty differs from the first. Medical physicists who recently completed each ABR exam portion will share their experiences, insights, and preparation methods to help attendees best prepare for the challenges of each part of the ABR exam. In accordance with ABR exam security policy, no recalls or exam questions will be discussed. Learning Objectives: How to prepare for Part 1 of the ABR exam by determining the scope of basic medical physics study material and related problem solving/calculations How to prepare for Part 2 of the ABR exam by understanding diagnostic and/or nuclear imaging physics, systems, dosimetry, safety and related problem solving/calculations How to prepare for Part 3 of the ABR exam by effectively communicating the practice, methods, and significance of clinical diagnostic and/or nuclear medical physics.« less

WE-D-213-04: Preparing for Parts 2 & 3 of the ABR Nuclear Medicine Physics Exam

DOE Office of Scientific and Technical Information (OSTI.GOV)

MacDougall, R.

Adequate, efficient preparation for the ABR Diagnostic and Nuclear Medical Physics exams is key to successfully obtain ABR professional certification. Each part of the ABR exam presents its own challenges: Part I: Determine the scope of basic medical physics study material, efficiently review this material, and solve related written questions/problems. Part II: Understand imaging principles, modalities, and systems, including image acquisition, processing, and display. Understand the relationship between imaging techniques, image quality, patient dose and safety, and solve related written questions/problems. Part III: Gain crucial, practical, clinical medical physics experience. Effectively communicate and explain the practice, performance, and significance ofmore » all aspects of clinical medical physics. All three parts of the ABR exam require specific skill sets and preparation: mastery of basic physics and imaging principles; written problem solving often involving rapid calculation; responding clearly and succinctly to oral questions about the practice, methods, and significance of clinical medical physics. This symposium focuses on the preparation and skill sets necessary for each part of the ABR exam. Although there is some overlap, the nuclear exam covers a different body of knowledge than the diagnostic exam. A separate speaker will address those aspects that are unique to the nuclear exam. Medical physicists who have recently completed each of part of the ABR exam will share their experiences, insights, and preparation methods to help attendees best prepare for the challenges of each part of the ABR exam. In accordance with ABR exam security policy, no recalls or exam questions will be discussed. Learning Objectives: How to prepare for Part 1 of the ABR exam by determining the scope of basic medical physics study material and related problem solving/calculations How to Prepare for Part 2 of the ABR exam by understanding diagnostic and/or nuclear imaging physics, systems, dosimetry, safety and related problem solving/calculations How to Prepare for Part 3 of the ABR exam by effectively communicating the practice, methods, and significance of clinical diagnostic and/or nuclear medical physics.« less

WE-D-213-00: Preparing for the ABR Diagnostic and Nuclear Medicine Physics Exams

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

Adequate, efficient preparation for the ABR Diagnostic and Nuclear Medical Physics exams is key to successfully obtain ABR professional certification. Each part of the ABR exam presents its own challenges: Part I: Determine the scope of basic medical physics study material, efficiently review this material, and solve related written questions/problems. Part II: Understand imaging principles, modalities, and systems, including image acquisition, processing, and display. Understand the relationship between imaging techniques, image quality, patient dose and safety, and solve related written questions/problems. Part III: Gain crucial, practical, clinical medical physics experience. Effectively communicate and explain the practice, performance, and significance ofmore » all aspects of clinical medical physics. All three parts of the ABR exam require specific skill sets and preparation: mastery of basic physics and imaging principles; written problem solving often involving rapid calculation; responding clearly and succinctly to oral questions about the practice, methods, and significance of clinical medical physics. This symposium focuses on the preparation and skill sets necessary for each part of the ABR exam. Although there is some overlap, the nuclear exam covers a different body of knowledge than the diagnostic exam. A separate speaker will address those aspects that are unique to the nuclear exam. Medical physicists who have recently completed each of part of the ABR exam will share their experiences, insights, and preparation methods to help attendees best prepare for the challenges of each part of the ABR exam. In accordance with ABR exam security policy, no recalls or exam questions will be discussed. Learning Objectives: How to prepare for Part 1 of the ABR exam by determining the scope of basic medical physics study material and related problem solving/calculations How to Prepare for Part 2 of the ABR exam by understanding diagnostic and/or nuclear imaging physics, systems, dosimetry, safety and related problem solving/calculations How to Prepare for Part 3 of the ABR exam by effectively communicating the practice, methods, and significance of clinical diagnostic and/or nuclear medical physics.« less

WE-D-213-01: Preparing for Part 1 of the ABR Diagnostic Physics Exam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simiele, S.

Adequate, efficient preparation for the ABR Diagnostic and Nuclear Medical Physics exams is key to successfully obtain ABR professional certification. Each part of the ABR exam presents its own challenges: Part I: Determine the scope of basic medical physics study material, efficiently review this material, and solve related written questions/problems. Part II: Understand imaging principles, modalities, and systems, including image acquisition, processing, and display. Understand the relationship between imaging techniques, image quality, patient dose and safety, and solve related written questions/problems. Part III: Gain crucial, practical, clinical medical physics experience. Effectively communicate and explain the practice, performance, and significance ofmore » all aspects of clinical medical physics. All three parts of the ABR exam require specific skill sets and preparation: mastery of basic physics and imaging principles; written problem solving often involving rapid calculation; responding clearly and succinctly to oral questions about the practice, methods, and significance of clinical medical physics. This symposium focuses on the preparation and skill sets necessary for each part of the ABR exam. Although there is some overlap, the nuclear exam covers a different body of knowledge than the diagnostic exam. A separate speaker will address those aspects that are unique to the nuclear exam. Medical physicists who have recently completed each of part of the ABR exam will share their experiences, insights, and preparation methods to help attendees best prepare for the challenges of each part of the ABR exam. In accordance with ABR exam security policy, no recalls or exam questions will be discussed. Learning Objectives: How to prepare for Part 1 of the ABR exam by determining the scope of basic medical physics study material and related problem solving/calculations How to Prepare for Part 2 of the ABR exam by understanding diagnostic and/or nuclear imaging physics, systems, dosimetry, safety and related problem solving/calculations How to Prepare for Part 3 of the ABR exam by effectively communicating the practice, methods, and significance of clinical diagnostic and/or nuclear medical physics.« less

WE-D-213-03: Preparing for Part 3 of the ABR Diagnostic Physics Exam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bevins, N.

Adequate, efficient preparation for the ABR Diagnostic and Nuclear Medical Physics exams is key to successfully obtain ABR professional certification. Each part of the ABR exam presents its own challenges: Part I: Determine the scope of basic medical physics study material, efficiently review this material, and solve related written questions/problems. Part II: Understand imaging principles, modalities, and systems, including image acquisition, processing, and display. Understand the relationship between imaging techniques, image quality, patient dose and safety, and solve related written questions/problems. Part III: Gain crucial, practical, clinical medical physics experience. Effectively communicate and explain the practice, performance, and significance ofmore » all aspects of clinical medical physics. All three parts of the ABR exam require specific skill sets and preparation: mastery of basic physics and imaging principles; written problem solving often involving rapid calculation; responding clearly and succinctly to oral questions about the practice, methods, and significance of clinical medical physics. This symposium focuses on the preparation and skill sets necessary for each part of the ABR exam. Although there is some overlap, the nuclear exam covers a different body of knowledge than the diagnostic exam. A separate speaker will address those aspects that are unique to the nuclear exam. Medical physicists who have recently completed each of part of the ABR exam will share their experiences, insights, and preparation methods to help attendees best prepare for the challenges of each part of the ABR exam. In accordance with ABR exam security policy, no recalls or exam questions will be discussed. Learning Objectives: How to prepare for Part 1 of the ABR exam by determining the scope of basic medical physics study material and related problem solving/calculations How to Prepare for Part 2 of the ABR exam by understanding diagnostic and/or nuclear imaging physics, systems, dosimetry, safety and related problem solving/calculations How to Prepare for Part 3 of the ABR exam by effectively communicating the practice, methods, and significance of clinical diagnostic and/or nuclear medical physics.« less

WE-D-213-02: Preparing for Part 2 of the ABR Diagnostic Physics Exam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zambelli, J.

Adequate, efficient preparation for the ABR Diagnostic and Nuclear Medical Physics exams is key to successfully obtain ABR professional certification. Each part of the ABR exam presents its own challenges: Part I: Determine the scope of basic medical physics study material, efficiently review this material, and solve related written questions/problems. Part II: Understand imaging principles, modalities, and systems, including image acquisition, processing, and display. Understand the relationship between imaging techniques, image quality, patient dose and safety, and solve related written questions/problems. Part III: Gain crucial, practical, clinical medical physics experience. Effectively communicate and explain the practice, performance, and significance ofmore » all aspects of clinical medical physics. All three parts of the ABR exam require specific skill sets and preparation: mastery of basic physics and imaging principles; written problem solving often involving rapid calculation; responding clearly and succinctly to oral questions about the practice, methods, and significance of clinical medical physics. This symposium focuses on the preparation and skill sets necessary for each part of the ABR exam. Although there is some overlap, the nuclear exam covers a different body of knowledge than the diagnostic exam. A separate speaker will address those aspects that are unique to the nuclear exam. Medical physicists who have recently completed each of part of the ABR exam will share their experiences, insights, and preparation methods to help attendees best prepare for the challenges of each part of the ABR exam. In accordance with ABR exam security policy, no recalls or exam questions will be discussed. Learning Objectives: How to prepare for Part 1 of the ABR exam by determining the scope of basic medical physics study material and related problem solving/calculations How to Prepare for Part 2 of the ABR exam by understanding diagnostic and/or nuclear imaging physics, systems, dosimetry, safety and related problem solving/calculations How to Prepare for Part 3 of the ABR exam by effectively communicating the practice, methods, and significance of clinical diagnostic and/or nuclear medical physics.« less

Application of high explosion cratering data to planetary problems

NASA Technical Reports Server (NTRS)

Oberbeck, V. R.

1977-01-01

The present paper deals with the conditions of explosion or nuclear cratering required to simulate impact crater formation. Some planetary problems associated with three different aspects of crater formation are discussed, and solutions based on high-explosion data are proposed. Structures of impact craters and some selected explosion craters formed in layered media are examined and are related to the structure of lunar basins. The mode of ejection of material from impact craters is identified using explosion analogs. The ejection mode is shown to have important implications for the origin of material in crater and basin deposits. Equally important are the populations of secondary craters on lunar and planetary surfaces.

Crack problems involving nonhomogeneous interfacial regions in bonded materials

NASA Technical Reports Server (NTRS)

Erdogan, F.

1990-01-01

Consideration is given to two classes of fracture-related solid mechanics problems in which the model leads to some physically anomalous results. The first is the interface crack problem associated with the debonding process in which the corresponding elasticity solution predicts severe oscillations of stresses and the crack surface displacements vary near the crack tip. The second deals with crack intersecting the interface. The nature of the solutions around the crack tips arising from these problems is reviewed. The rationale for introducing a new interfacial zone model is discussed, its analytical consequences within the context of the two crack-problem classes are described, and some examples are presented.

Advanced Materials and Coatings for Aerospace Applications

NASA Technical Reports Server (NTRS)

Miyoshi, Kazuhisa

2004-01-01

In the application area of aerospace tribology, researchers and developers must guarantee the highest degree of reliability for materials, components, and systems. Even a small tribological failure can lead to catastrophic results. The absence of the required knowledge of tribology, as Professor H.P. Jost has said, can act as a severe brake in aerospace vehicle systems-and indeed has already done so. Materials and coatings must be able to withstand the aerospace environments that they encounter, such as vacuum terrestrial, ascent, and descent environments; be resistant to the degrading effects of air, water vapor, sand, foreign substances, and radiation during a lengthy service; be able to withstand the loads, stresses, and temperatures encountered form acceleration and vibration during operation; and be able to support reliable tribological operations in harsh environments throughout the mission of the vehicle. This presentation id divided into two sections: surface properties and technology practice related to aerospace tribology. The first section is concerned with the fundamental properties of the surfaces of solid-film lubricants and related materials and coatings, including carbon nanotubes. The second is devoted to applications. Case studies are used to review some aspects of real problems related to aerospace systems to help engineers and scientists to understand the tribological issues and failures. The nature of each problem is analyzed, and the tribological properties are examined. All the fundamental studies and case studies were conducted at the NASA Glenn Research Center.

Faded-example as a Tool to Acquire and Automate Mathematics Knowledge

NASA Astrophysics Data System (ADS)

Retnowati, E.

2017-04-01

Students themselves accomplish Knowledge acquisition and automation. The teacher plays a role as the facilitator by creating mathematics tasks that assist students in building knowledge efficiently and effectively. Cognitive load caused by learning material presented by teachers should be considered as a critical factor. While the intrinsic cognitive load is related to the degree of complexity of the material learning ones can handle, the extraneous cognitive load is directly caused by how the material is presented. Strategies to present a learning material in computational learning domains like mathematics are a namely worked example (fully-guided task) or problem-solving (discovery task with no guidance). According to the empirical evidence, learning based on problem-solving may cause high-extraneous cognitive load for students who have limited prior knowledge, conversely learn based on worked example may cause high-extraneous cognitive load for students who have mastered the knowledge base. An alternative is a faded example consisting of the partly-completed task. Learning from faded-example can facilitate students who already acquire some knowledge about the to-be-learned material but still need more practice to automate the knowledge further. This instructional strategy provides a smooth transition from a fully-guided into an independent problem solver. Designs of faded examples for learning trigonometry are discussed.

Hydrologic-information needs for oil-shale development, northwestern Colorado

USGS Publications Warehouse

Taylor, O.J.

1982-01-01

Hydrologic information is not adequate for proper development of the large oil-shale reserves of Piceance basin in northwestern Colorado. Exploratory drilling and aquifer testing are needed to define the hydrologic system, to provide wells for aquifer testing, to design mine-drainage techniques, and to explore for additional water supplies. Sampling networks are needed to supply hydrologic data on the quantity and quality of surface water, ground water, and springs. A detailed sampling network is proposed for the White River basin because of expected impacts related to water supplies and waste disposal. Emissions from oil-shale retorts to the atmosphere need additional study because of possible resulting corrosion problems and the destruction of fisheries. Studies of the leachate materials and the stability of disposed retorted shale piles are needed to insure that these materials will not cause problems. Hazards related to in-situ retorts, and the wastes related to oil-shale development in general also need further investigation. (USGS)

Easy as ABCABC: Abstract Language Facilitates Performance on a Concrete Patterning Task

ERIC Educational Resources Information Center

Fyfe, Emily R.; McNeil, Nicole M.; Rittle-Johnson, Bethany

2015-01-01

The labels used to describe patterns and relations can influence children's relational reasoning. In this study, 62 preschoolers (M[subscript age] = 4.4 years) solved and described eight pattern abstraction problems (i.e., recreated the relation in a model pattern using novel materials). Some children were exposed to concrete labels (e.g.,…

Genetics Home Reference: Koolen-de Vries syndrome

MedlinePlus

... of Koolen-de Vries syndrome , has undergone an inversion . An inversion involves two breaks in a chromosome; the resulting ... lineage have no health problems related to the inversion. However, genetic material can be lost or duplicated ...

Investigation of a novel approach for the cross-linking characterization of SU-8 photoresist materials by means of optical dispersion measurements

NASA Astrophysics Data System (ADS)

Taudt, Ch.; Baselt, T.; Koch, E.; Hartmann, P.

2014-03-01

The increase in efficiency and precision in the production of semiconductor structures under the use of polymeric materials like SU-8 is crucial in securing the technological innovation within this industry. The manufacturing of structures on wafers demands a high quality of materials, tools and production processes. In particular, deviations in the materials' parameters (e.g. cross-linking state, density or mechanical properties) could lead to subsequent problems such as a reduced lifetime of structures and systems. In particular problems during the soft and post-exposure bake process can lead to an inhomogeneous distribution of material properties. This paper describes a novel approach for the characterization of SU-8 material properties in relation to a second epoxy-based material of different cross-linking by the measurement of optical dispersion within the material. A white-light interferometer was used. In particular the setup consisted of a white-light source, a Michelson-type interferometer and a spectrometer. The investigation of the dispersion characteristics was carried out by the detection of the equalization wavelength for different positions of the reference arm in a range from 400 to 900 nm. The measured time delay due to dispersion ranges from 850 to 1050 ps/m. For evaluation purposes a 200μm SU-8 sample was characterized in the described setup regarding its dispersion characteristics in relation to bulk epoxy material. The novel measurement approach allowed a fast and high-resolution material characterization for SU-8 micro structures which was suitable for integration in production lines. The outlook takes modifications of the experimental setup regarding on-wafer measurements into account.

Predicting materials for sustainable energy sources: The key role of density functional theory

NASA Astrophysics Data System (ADS)

Galli, Giulia

Climate change and the related need for sustainable energy sources replacing fossil fuels are pressing societal problems. The development of advanced materials is widely recognized as one of the key elements for new technologies that are required to achieve a sustainable environment and provide clean and adequate energy for our planet. We discuss the key role played by Density Functional Theory, and its implementations in high performance computer codes, in understanding, predicting and designing materials for energy applications.

Multicultural Curriculum Training with Pre-Student Teachers in Language Arts.

ERIC Educational Resources Information Center

Hubble, Martha Weidman

This study relates to two problems in multicultural education: the inability of teachers to relate to and understand the culturally diverse learner; and the dearth of teaching materials based on the minority group members' cultural heritages. A Multicultural Curriculum Training (MCT) program was developed to promote in prospective teachers an…

How Brooding Minds Inhibit Negative Material: An Event-Related fMRI Study

ERIC Educational Resources Information Center

Vanderhasselt, Marie-Anne; Baeken, Chris; Van Schuerbeek, Peter; Luypaert, Rob; De Mey, Johan; De Raedt, Rudi

2013-01-01

Depressive brooding--a passive ruminative focus on one's problems, negative mood and their consequences--is a thinking style that places individuals at a greater risk to develop future psychopathology. In this study, we investigated whether inter-individual differences in depressive brooding are related to neural differences underlying the…

Multi-objective robust design of energy-absorbing components using coupled process-performance simulations

NASA Astrophysics Data System (ADS)

Najafi, Ali; Acar, Erdem; Rais-Rohani, Masoud

2014-02-01

The stochastic uncertainties associated with the material, process and product are represented and propagated to process and performance responses. A finite element-based sequential coupled process-performance framework is used to simulate the forming and energy absorption responses of a thin-walled tube in a manner that both material properties and component geometry can evolve from one stage to the next for better prediction of the structural performance measures. Metamodelling techniques are used to develop surrogate models for manufacturing and performance responses. One set of metamodels relates the responses to the random variables whereas the other relates the mean and standard deviation of the responses to the selected design variables. A multi-objective robust design optimization problem is formulated and solved to illustrate the methodology and the influence of uncertainties on manufacturability and energy absorption of a metallic double-hat tube. The results are compared with those of deterministic and augmented robust optimization problems.

HEMP 3D: A finite difference program for calculating elastic-plastic flow, appendix B

NASA Astrophysics Data System (ADS)

Wilkins, Mark L.

1993-05-01

The HEMP 3D program can be used to solve problems in solid mechanics involving dynamic plasticity and time dependent material behavior and problems in gas dynamics. The equations of motion, the conservation equations, and the constitutive relations listed below are solved by finite difference methods following the format of the HEMP computer simulation program formulated in two space dimensions and time.

Partnering for A Solution: A Case Study

NASA Technical Reports Server (NTRS)

Jimenez-Smith, Deyrah

2003-01-01

A material-related issue has been identified, which has the potential of impacting the Space Program. Although "in-house" efforts have been underway to solve the problem, a solution has not yet been reached. This presentation shows how a GIDEP member organization is using a Problem Advisory as a solution approach in an effort to receive information from other industry and/or government organizations that may contribute in finding a solution.

Interdisciplinary research and development on the effects of the nature and properties of ceramic materials in the design of advanced structural components

NASA Technical Reports Server (NTRS)

1978-01-01

An educational development and supportive research program on ceramic materials established to advance design methodology, improve materials, and develop engineers knowledgable in design with and use of high performance ceramic materials is described. Emphasis is on the structures and related materials problems in a ceramic turbine engine, but applications in coal gasification, solar conversion, and magnetohydrodynamic technologies are considered. Progress of various research projects in the areas of new materials, processing, characterization, and nondestructive testing is reported. Fracture toughness determination, extended X-ray absorption fine structure measurements, and grain boundary effects in beta-alumina are among the topics covered.

Changes in Body Mass Index and Stoma Related Problems in the Elderly

PubMed Central

Skeps, Raymond; McMullen, Carmit K.; Wendel, Christopher S.; Bulkley, Joanna; Grant, Marcia; Mohler, Jane; Hornbrook, Mark C.; Krouse, Robert S.; Herrinton, Lisa J.

2012-01-01

Objectives Weight gain can cause retraction of an intestinal stoma, possibly resulting in difficulty with wafer and pouch fit, daily care challenges, and discomfort. This cross-sectional study examined the association between body mass index (BMI) and ostomy-related problems among long-term (>5 years post-diagnosis) colorectal cancer (CRC) survivors. Materials and Methods CRC survivors from three Kaiser Permanente Regions completed a mailed survey. The response rate for those with an ostomy was 53% (283/529). Questions included stoma-related problems and time to conduct daily ostomy care. Poisson regression evaluated associations between report of problems and change in BMI. Our analysis sample included 235 survivors. Results Sample was 76% ≥65 years of age. Since their surgeries, BMI remained stable in 44% (ST), decreased in 20% (DE), and increased in 35% (IN) of survivors. Compared to ST, male IN (RR 2.15 [1.09–4.25]) and female DE (RR 5.06 [1.26–25.0]) were more likely to spend more than 30 minutes per day on stoma care. IN (vs. ST) were more likely to report interference with clothing (RR 1.51 [1.06–2.17]) and other stoma-related problems (RR 2.32 [1.30–4.14]). Survivors who were obese at time of survey were more likely to report interference with clothing (RR 1.88 [1.38–2.56]) and other stoma-related problems (RR 1.68 [1.07–2.65]). Conclusion A change in BMI is associated with ostomy-related problems among long-term CRC survivors. Equipment and care practices may need to be adapted for changes in abdominal shape. Health care providers should caution that a significant increase or decrease in BMI may cause ostomy-related problems. PMID:24071496

Final Technical Report for DE-SC0001878 [Theory and Simulation of Defects in Oxide Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chelikowsky, James R.

2014-04-14

We explored a wide variety of oxide materials and related problems, including materials at the nanoscale and generic problems associated with oxide materials such as the development of more efficient computational tools to examine these materials. We developed and implemented methods to understand the optical and structural properties of oxides. For ground state properties, our work is predominantly based on pseudopotentials and density functional theory (DFT), including new functionals and going beyond the local density approximation (LDA): LDA+U. To study excited state properties (quasiparticle and optical excitations), we use time dependent density functional theory, the GW approach, and GW plusmore » Bethe-Salpeter equation (GW-BSE) methods based on a many-body Green function approaches. Our work focused on the structural, electronic, optical and magnetic properties of defects (such as oxygen vacancies) in hafnium oxide, titanium oxide (both bulk and clusters) and related materials. We calculated the quasiparticle defect states and charge transition levels of oxygen vacancies in monoclinic hafnia. we presented a milestone G0W0 study of two of the crystalline phases of dye-sensitized TiO{sub 2} clusters. We employed hybrid density functional theory to examine the electronic structure of sexithiophene/ZnO interfaces. To identify the possible effect of epitaxial strain on stabilization of the ferromagnetic state of LaCoO{sub 3} (LCO), we compare the total energy of the magnetic and nonmagnetic states of the strained theoretical bulk structure.« less

Case histories of building material problems caused by condensation at an enclosed swimming pool and an enclosed ice rink

DOE Office of Scientific and Technical Information (OSTI.GOV)

VanGeem, M.G.; Farahmandpour, K.; Gajda, J.

1999-07-01

Enclosed swimming pools and ice rinks in winter climates have the potential for high indoor relative humidities and cold building materials. These elements can contribute to condensation and premature deterioration of building materials. Case histories are provided for an enclosed swimming pool and an enclosed ice rink with condensation problems. An evaluation was performed after roof leaks were reported at a recently constructed indoor swimming pool in a Chicago suburb. After a preliminary inspection, it was evident that the reported leaks were related to building moisture problems rather than a roof leak. Exterior brick masonry exhibited heavy efflorescence in themore » area of the swimming pools, and water streaks were visible on the exterior walls below the eaves. The evaluation included laboratory testing, a visual inspection, field tests and measurements, and analyses for condensation potential. Results of the evaluation indicated the presence of condensed moisture as a direct cause of the observed water stains, and masonry efflorescence. Recommended corrective actions developed. A 54-year-old enclosed ice rink in New England was under investigation to determine the cause of a deteriorated wood deck roof. The building did not have dehumidification or air handling systems, and was heated only when occupied. The evaluation included visual inspection and analyses for condensation potential. Results of the evaluation indicated condensation within the wood decking and insulation during winter months, and high relative humidities that prohibited drying during the spring, summer, and fall. These conditions, over an extended number of years, resulted in decay of the wood decking.« less

Materials-Related Aspects of Thermochemical Water and Carbon Dioxide Splitting: A Review

PubMed Central

Roeb, Martin; Neises, Martina; Monnerie, Nathalie; Call, Friedemann; Simon, Heike; Sattler, Christian; Schmücker, Martin; Pitz-Paal, Robert

2012-01-01

Thermochemical multistep water- and CO2-splitting processes are promising options to face future energy problems. Particularly, the possible incorporation of solar power makes these processes sustainable and environmentally attractive since only water, CO2 and solar power are used; the concentrated solar energy is converted into storable and transportable fuels. One of the major barriers to technological success is the identification of suitable active materials like catalysts and redox materials exhibiting satisfactory durability, reactivity and efficiencies. Moreover, materials play an important role in the construction of key components and for the implementation in commercial solar plants. The most promising thermochemical water- and CO2-splitting processes are being described and discussed with respect to further development and future potential. The main materials-related challenges of those processes are being analyzed. Technical approaches and development progress in terms of solving them are addressed and assessed in this review.

Status and applications of diamond and diamond-like materials: An emerging technology

NASA Technical Reports Server (NTRS)

1990-01-01

Recent discoveries that make possible the growth of crystalline diamond by chemical vapor deposition offer the potential for a wide variety of new applications. This report takes a broad look at the state of the technology following from these discoveries in relation to other allied materials, such as high-pressure diamond and cubic boron nitride. Most of the potential defense, space, and commercial applications are related to diamond's hardness, but some utilize other aspects such as optical or electronic properties. The growth processes are reviewed, and techniques for characterizing the resulting materials' properties are discussed. Crystalline diamond is emphasized, but other diamond-like materials (silicon carbide, amorphous carbon containing hydrogen) are also examined. Scientific, technical, and economic problem areas that could impede the rapid exploitation of these materials are identified. Recommendations are presented covering broad areas of research and development.

[Enclosed environments and health].

PubMed

Maroni, M; Barbieri, F

1989-01-01

Problems related to Indoor Air Quality are subject of study since about twenty years. New architectural criteria, new building materials and increasing demands of energy saving have progressively changed residences, offices and all non-industrial indoor environments. This paper present a review of the IAQ-related issues from sources characterization, to pollutant assessment and definition of effects on human health.

Educational differences in leisure-time physical inactivity: a descriptive and explanatory study.

PubMed

Droomers, M; Schrijvers, C T; van de Mheen, H; Mackenbach, J P

1998-12-01

In this study we aim to explain educational differences in leisure-time physical inactivity in terms of psychosocial and material factors. Cross-sectional data were obtained from the baseline of the Dutch GLOBE study in 1991, including 2598 men and women, aged 15-74 years. Physical inactivity during leisure time was defined as not participating in any activity, such as sports, gardening, walking or cycling. Psychosocial factors included in the study were coping resources, personality, and stressors. Material factors were financial situation, employment status, and living conditions. Logistic regression models were used to calculate educational differences in physical inactivity. Physical inactivity was more prevalent in lower educational groups. Psychosocial factors related to physical inactivity were locus of control, parochialism, neuroticism, emotional social support, active problem focussing, optimistic and palliative coping styles. Material factors associated with physical inactivity were income, employment status and financial problems. All correlates of physical inactivity were unequally distributed over educational groups, except optimistic and palliative coping. Personality and coping style were the main contributors to the observed educational differences in physical inactivity. That is to say, parochialism, locus of control, neuroticism and active problem focussing explained about half of elevated odds ratios of physical inactivity in the lower educational groups. The material factors, equivalent income and employment status explained about 40% of the elevated odds ratios. Psychosocial and material correlates together reduced the odds ratios of lower educational groups by on average 75%. These results have practical consequences for the design of more effective interventions to promote physical activity. In particular, personality and coping style of risk groups, such as lower educational groups, should be taken into consideration at the future development of these interventions, as well as inequalities in material restrictions related to engaging in physical activity. Supplementary interventions focussing on childhood conditions which, partly, influence both personality and physical inactivity may also contribute to a reduction of socio-economic differences in physical inactivity.

MARS-MD: rejection based image domain material decomposition

NASA Astrophysics Data System (ADS)

Bateman, C. J.; Knight, D.; Brandwacht, B.; McMahon, J.; Healy, J.; Panta, R.; Aamir, R.; Rajendran, K.; Moghiseh, M.; Ramyar, M.; Rundle, D.; Bennett, J.; de Ruiter, N.; Smithies, D.; Bell, S. T.; Doesburg, R.; Chernoglazov, A.; Mandalika, V. B. H.; Walsh, M.; Shamshad, M.; Anjomrouz, M.; Atharifard, A.; Vanden Broeke, L.; Bheesette, S.; Kirkbride, T.; Anderson, N. G.; Gieseg, S. P.; Woodfield, T.; Renaud, P. F.; Butler, A. P. H.; Butler, P. H.

2018-05-01

This paper outlines image domain material decomposition algorithms that have been routinely used in MARS spectral CT systems. These algorithms (known collectively as MARS-MD) are based on a pragmatic heuristic for solving the under-determined problem where there are more materials than energy bins. This heuristic contains three parts: (1) splitting the problem into a number of possible sub-problems, each containing fewer materials; (2) solving each sub-problem; and (3) applying rejection criteria to eliminate all but one sub-problem's solution. An advantage of this process is that different constraints can be applied to each sub-problem if necessary. In addition, the result of this process is that solutions will be sparse in the material domain, which reduces crossover of signal between material images. Two algorithms based on this process are presented: the Segmentation variant, which uses segmented material classes to define each sub-problem; and the Angular Rejection variant, which defines the rejection criteria using the angle between reconstructed attenuation vectors.

Crack Initiation and Propagation Properties of HY 130 Steel Weldments Following Temper Embrittlement.

DTIC Science & Technology

1982-09-01

mechanics ( EPFM ) may be applied to engineering problems to determine material properties related to crack initiation and propagation. Specifically, these...Introduction The application of linear elastic fracture mechanics (LEFM) to engineering fracture analyses has become increasingly widespread and the use...structures to which the particular material was to be applied. The advent of elastic-plastic fracture mechanics ( EPFM ) has proven valuable because a

Accelerated Insertion of Materials - Composites (AIM-C) Methodology

DTIC Science & Technology

2004-05-12

the groups even after this point in the maturation process, but the key is that the applications team must know what the technology development team...Threats ( SWOT ) analysis? Was a check made of past showstoppers/major issues related to problem statements of a similar nature? (This will be...in this methodology and in the AIM-C system is helpful to performing strength, weakness, opportunities, and threats ( SWOT ) analyses on the materials

Selective loss of verbal imagery.

PubMed

Mehta, Z; Newcombe, F

1996-05-01

This single case study of the ability to generate verbal and non-verbal imagery in a woman who sustained a gunshot wound to the brain reports a significant difficulty in generating images of word shapes but not a significant problem in generating object images. Further dissociation, however, was observed in her ability to generate images of living vs non-living material. She made more errors in imagery and factual information tasks for non-living items than for living items. This pattern contrasts with our previous report of the agnosic patient, M.S., who had severe difficulty in generating images of living material, whereas his ability to image the shape of words was comparable to that of normal control subjects. Furthermore, with regard to the generation of images of living compared with non-living material, M.S. shows more errors with living than nonliving items. In contrast, the present patient, S.M., made significantly more errors with non-living relative to living items. There appear to be two types of double dissociation which reinforce the growing evidence of dissociable impairments in the ability to generate images for different types of verbal and non-verbal material. Such dissociations, presumably related to sensory and cognitive processing demands, address the problem of the neural basis of imagery.

Born into adversity: psychological distress in two birth cohorts of second-generation Irish children growing up in Britain.

PubMed

Das-Munshi, J; Clark, C; Dewey, M E; Leavey, G; Stansfeld, S A; Prince, M J

2014-03-01

Worldwide, the Irish diaspora experience health inequalities persisting across generations. The present study sought to establish the prevalence of psychological morbidity in the children of migrant parents from Ireland, and reasons for differences. Data from two British birth cohorts were used for analysis. Each surveyed 17 000 babies born in one week in 1958 and 1970 and followed up through childhood. Validated scales assessed psychological health. Relative to the rest of the cohort, second-generation Irish children grew up in material hardship and showed greater psychological problems at ages 7, 11 (1958 cohort) and 16 (both cohorts). Adjusting for material adversity and maternal psychological distress markedly reduced differences. Relative to non-Irish parents, Irish-born parents were more likely to report chronic health problems (odds ratio [OR]: 1.29; 95% confidence interval [CI]: 1.08-1.54), and Irish-born mothers were more likely to be psychologically distressed (OR: 1.44; 95% CI: 1.13-1.84, when child was 10). Effect sizes diminished once material adversity was taken into account. Second-generation Irish children experienced high levels of psychological morbidity, but this was accounted for through adverse material circumstances in childhood and psychological distress in parents. Public health initiatives focusing on settlement experiences may reduce health inequalities in migrant children.

Bi-material plane with interface crack for the model of semi-linear material

NASA Astrophysics Data System (ADS)

Domanskaya, T. O.; Malkov, V. M.; Malkova, Yu. V.

2018-05-01

The singular plane problems of nonlinear elasticity (plane strain and plane stress) are considered for bi-material infinite plane with interface crack. The plane is formed of two half-planes. Mechanical properties of half-planes are described by the model of semi-linear material. Using model of this harmonic material has allowed to apply the theory of complex functions and to obtain exact analytical global solutions of some nonlinear problems. Among them the problem of bi-material plane with the stresses and strains jumps at an interface is considered. As an application of the problem of jumps, the problem of interface crack is solved. The values of nominal (Piola) and Cauchy stresses and displacements are founded. Based on the global solutions the asymptotic expansions are constructed for stresses and displacements in a vicinity of crack tip. As an example the case of a free crack in bi-material plane subjected to constant stresses at infinity is studied. As a special case, the analytical solution of the problem of a crack in a homogeneous plane is obtained from the problem for bi-material plane with interface crack.

Evaluation of moisture barrier coatings on carbon-phenolic SRM nozzle materials

NASA Technical Reports Server (NTRS)

Mcnutt, Ronald C.

1986-01-01

The carbon-phenolic composite ablative material used on the Solid Rocket Motor (SRM) nozzle is known to absorb moisture from the atmosphere. This could cause problems such as pocketing during firing. Several moisture barrier coatings were tested on the SRM nozzle material. Data are presented for six of the 12 coatings to be tested. The data were obtained from immersion of coated samples in an environmental chamber at 100 F and 100% relative humidity and by using a modified TGA (thermal gravimetric analysis) technique. The TGA technique involved allowing wet nitrogen (25 C, 80% relative humidity) to flow across a small sample at about 65 cu cm per minute while continually monitoring the weight increase. These preliminary results show Kel-F-800, a material supplied by 3M Corporation to be the better moisture barrier. A second task was to collect data on the relative absorption of water and kerosene into the carbon-phenolic SRM nozzle material. These data indicate that water absorbs into the nozzle material to a much greater extent than kerosene. Thus kerosene is the more likely solvent in which to make specific gravity measurements on the SRM nozzle material.

Thermal design of composite material high temperature attachments

NASA Technical Reports Server (NTRS)

1972-01-01

An evaluation has been made of the thermal aspects of utilizing advanced filamentary composite materials as primary structures on the shuttle vehicle. The technical objectives of this study are to: (1) establish and design concepts for maintaining material temperatures within allowable limits at TPS attachments and or penetrations applicable to the space shuttle; and (2) verify the thermal design analysis by testing selected concepts. Specific composite materials being evaluated are boron epoxy, graphite/epoxy, boron polyimide, and boron aluminum; graphite/polyimide has been added to this list for property data identification and preliminary evaluation of thermal design problems. The TPS standoff to composite structure attachment over-temperature problem is directly related to TPS maximum surface temperature. To provide a thermally comprehensive evaluation of attachment temperature characteristics, maximum surface temperatures of 900 F, 1200 F, 1800 F, 2500 F and 3000 F are considered in this study. This range of surface temperatures and the high and low maximum temperature capability of the selected composite materials will result in a wide range of thermal requirements for composite/TPS standoff attachments.

Good practices in managing work-related indoor air problems: a psychosocial perspective.

PubMed

Lahtinen, Marjaana; Huuhtanen, Pekka; Vähämäki, Kari; Kähkönen, Erkki; Mussalo-Rauhamaa, Helena; Reijula, Kari

2004-07-01

Indoor air problems at workplaces are often exceedingly complex. Technical questions are interrelated with the dynamics of the work community, and the cooperation and interaction skills of the parties involved in the problem solving process are also put to the test. The objective of our study was to analyze the process of managing and solving indoor air problems from a psychosocial perspective. This collective case study was based on data from questionnaires, interviews and various documentary materials. Technical inspections of the buildings and indoor air measurements were also carried out. The following four factors best differentiated successful cases from impeded cases: extensive multiprofessional collaboration and participative action, systematic action and perseverance, investment in information and communication, and process thinking and learning. The study also proposed a theoretical model for the role of the psychosocial work environment in indoor air problems. The expertise related to social and human aspects of problem solving plays a significant role in solving indoor air problems. Failures to properly handle these aspects may lead to resources being wasted and result in a problematic situation becoming stagnant or worse. Copyright 2004 Wiley-Liss, Inc.

Advances in the surface modification techniques of bone-related implants for last 10 years

PubMed Central

Qiu, Zhi-Ye; Chen, Cen; Wang, Xiu-Mei; Lee, In-Seop

2014-01-01

At the time of implanting bone-related implants into human body, a variety of biological responses to the material surface occur with respect to surface chemistry and physical state. The commonly used biomaterials (e.g. titanium and its alloy, Co–Cr alloy, stainless steel, polyetheretherketone, ultra-high molecular weight polyethylene and various calcium phosphates) have many drawbacks such as lack of biocompatibility and improper mechanical properties. As surface modification is very promising technology to overcome such problems, a variety of surface modification techniques have been being investigated. This review paper covers recent advances in surface modification techniques of bone-related materials including physicochemical coating, radiation grafting, plasma surface engineering, ion beam processing and surface patterning techniques. The contents are organized with different types of techniques to applicable materials, and typical examples are also described. PMID:26816626

A cylindrical shell with an arbitrarily oriented crack

NASA Technical Reports Server (NTRS)

Yahsi, O. S.; Erdogan, F.

1982-01-01

The general problem of a shallow shell with constant curvatures is considered. It is assumed that the shell contains an arbitrarily oriented through crack and the material is specially orthotropic. The nonsymmetric problem is solved for arbitrary self equilibrating crack surface tractions, which, added to an appropriate solution for an uncracked shell, would give the result for a cracked shell under most general loading conditions. The problem is reduced to a system of five singular integral equations in a set of unknown functions representing relative displacements and rotations on the crack surfaces. The stress state around the crack tip is asymptotically analyzed and it is shown that the results are identical to those obtained from the two dimensional in plane and antiplane elasticity solutions. The numerical results are given for a cylindrical shell containing an arbitrarily oriented through crack. Some sample results showing the effect of the Poisson's ratio and the material orthotropy are also presented.

Effect of Tutorial Giving on The Topic of Special Theory of Relativity in Modern Physics Course Towards Students’ Problem-Solving Ability

NASA Astrophysics Data System (ADS)

Hartatiek; Yudyanto; Haryoto, Dwi

2017-05-01

A Special Theory of Relativity handbook has been successfully arranged to guide students tutorial activity in the Modern Physics course. The low of students’ problem-solving ability was overcome by giving the tutorial in addition to the lecture class. It was done due to the limited time in the class during the course to have students do some exercises for their problem-solving ability. The explicit problem-solving based tutorial handbook was written by emphasizing to this 5 problem-solving strategies: (1) focus on the problem, (2) picture the physical facts, (3) plan the solution, (4) solve the problem, and (5) check the result. This research and development (R&D) consisted of 3 main steps: (1) preliminary study, (2) draft I. product development, and (3) product validation. The developed draft product was validated by experts to measure the feasibility of the material and predict the effect of the tutorial giving by means of questionnaires with scale 1 to 4. The students problem-solving ability in Special Theory of Relativity showed very good qualification. It implied that the tutorial giving with the help of tutorial handbook increased students problem-solving ability. The empirical test revealed that the developed handbook was significantly affected in improving students’ mastery concept and problem-solving ability. Both students’ mastery concept and problem-solving ability were in middle category with gain of 0.31 and 0.41, respectively.

Phenomenological and mechanics aspects of nondestructive evaluation and characterization by sound and ultrasound of material and fracture properties

NASA Technical Reports Server (NTRS)

Fu, L. S. W.

1982-01-01

Developments in fracture mechanics and elastic wave theory enhance the understanding of many physical phenomena in a mathematical context. Available literature in the material, and fracture characterization by NDT, and the related mathematical methods in mechanics that provide fundamental underlying principles for its interpretation and evaluation are reviewed. Information on the energy release mechanism of defects and the interaction of microstructures within the material is basic in the formulation of the mechanics problems that supply guidance for nondestructive evaluation (NDE).

Building an archives in a medical library.

PubMed Central

Sammis, S K

1984-01-01

In 1979 the University of Medicine and Dentistry of New Jersey established an archives to collect, preserve, and retrieve important documentation related to its history. This paper examines various steps in building an archives and the development of a coherent collection policy, including potential sources for archival material. Problems and possible solutions concerning what to preserve from the vast quantities of material generated by an institution are considered. The relationship between the archives and the medical library and the requirements of the physical plant are discussed, including the storage and preservation of materials. PMID:6743876

Metallic anodes for next generation secondary batteries.

PubMed

Kim, Hansu; Jeong, Goojin; Kim, Young-Ugk; Kim, Jae-Hun; Park, Cheol-Min; Sohn, Hun-Joon

2013-12-07

Li-air(O2) and Li-S batteries have gained much attention recently and most relevant research has aimed to improve the electrochemical performance of air(O2) or sulfur cathode materials. However, many technical problems associated with the Li metal anode have yet to be overcome. This review mainly focuses on the electrochemical behaviors and technical issues related to metallic Li anode materials as well as other metallic anode materials such as alkali (Na) and alkaline earth (Mg) metals, including Zn and Al when these metal anodes were employed for various types of secondary batteries.

Exploring Communication Technology.

ERIC Educational Resources Information Center

Wood, Jimmie; Kellum, Mary

These teacher's materials for a seven-unit course were developed to help students develop technological literacy, career exploration, and problem-solving skills relative to the communication industries. The seven units are on an introduction to communication, verbal communication, design and sketching, drafting, graphic reproduction, photography,…

A Summary of Research on Energy Saving and Emission Reduction of Transportation

NASA Astrophysics Data System (ADS)

Cheng, Dongxiang; Wu, Lufen

2017-12-01

Road transport is an important part of transportation, and road in the field of energy-saving emission reduction is a very important industry. According to the existing problems of road energy saving and emission reduction, this paper elaborates the domestic and international research on energy saving and emission reduction from three aspects: road network optimization, pavement material and pavement maintenance. Road network optimization may be overlooked, and the research content is still relatively preliminary; pavement materials mainly from the asphalt pavement temperature mixed asphalt technology research; pavement maintenance technology development is relatively comprehensive.

History of materials used for recording static and dynamic occlusal contact marks: a literature review

PubMed Central

Rahul, G R.; Poduval, Soorya T.; Shetty, Karunakar; Gupta, Bhawna; Rajora, Varun

2013-01-01

In the discipline of prosthetic dentistry it is important not only to examine the occlusion, but to be able to record, store, and transfer the information. Over the years many occlusion testing materials have been used. It has been suggested the clinical recording and transfer of information using waxes and other occlusion recording materials have disadvantages relating to inaccuracy and problems of manipulation. Therefore, there has been introduction of many new systems for recording occlusion contacts to overcome such problems. The correct physiological recovery of occlusion posses as much a challenge as ever for every dentist and technician. Even the smallest high spots measuring just a few microns can cause dysfunctions like temporo-mandibular pain. Occlusal proportions are being constantly changed with every procedure. Therefore, an understanding of the synergy of the teeth in static and dynamic occlusion forms the basis of good dentistry. The purpose of this review article is to give and overview of the various materials and methods that have been used to record occlusal contact marks. Key words:Occlusal contact marks, Occlusion indicators, Occlusion test materials, Occlusion recording materials. PMID:24455051

Nanoporous Materials for the Onboard Storage of Natural Gas.

PubMed

Kumar, K Vasanth; Preuss, Kathrin; Titirici, Maria-Magdalena; Rodríguez-Reinoso, Francisco

2017-02-08

Climate change, global warming, urban air pollution, energy supply uncertainty and depletion, and rising costs of conventional energy sources are, among others, potential socioeconomic threats that our community faces today. Transportation is one of the primary sectors contributing to oil consumption and global warming, and natural gas (NG) is considered to be a relatively clean transportation fuel that can significantly improve local air quality, reduce greenhouse-gas emissions, and decrease the energy dependency on oil sources. Internal combustion engines (ignited or compression) require only slight modifications for use with natural gas; rather, the main problem is the relatively short driving distance of natural-gas-powered vehicles due to the lack of an appropriate storage method for the gas, which has a low energy density. The U.S. Department of Energy (DOE) has set some targets for NG storage capacity to obtain a reasonable driving range in automotive applications, ruling out the option of storing methane at cryogenic temperatures. In recent years, both academia and industry have foreseen the storage of natural gas by adsorption (ANG) in porous materials, at relatively low pressures and ambient temperatures, as a solution to this difficult problem. This review presents recent developments in the search for novel porous materials with high methane storage capacities. Within this scenario, both carbon-based materials and metal-organic frameworks are considered to be the most promising materials for natural gas storage, as they exhibit properties such as large surface areas and micropore volumes, that favor a high adsorption capacity for natural gas. Recent advancements, technological issues, advantages, and drawbacks involved in natural gas storage in these two classes of materials are also summarized. Further, an overview of the recent developments and technical challenges in storing natural gas as hydrates in wetted porous carbon materials is also included. Finally, an analysis of design factors and technical issues that need to be considered before adapting vehicles to ANG technology is also presented.

Approximate static condensation algorithm for solving multi-material diffusion problems on meshes non-aligned with material interfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kikinzon, Evgeny; Kuznetsov, Yuri; Lipnikov, Konstatin

In this study, we describe a new algorithm for solving multi-material diffusion problem when material interfaces are not aligned with the mesh. In this case interface reconstruction methods are used to construct approximate representation of interfaces between materials. They produce so-called multi-material cells, in which materials are represented by material polygons that contain only one material. The reconstructed interface is not continuous between cells. Finally, we suggest the new method for solving multi-material diffusion problems on such meshes and compare its performance with known homogenization methods.

Approximate static condensation algorithm for solving multi-material diffusion problems on meshes non-aligned with material interfaces

DOE PAGES

Kikinzon, Evgeny; Kuznetsov, Yuri; Lipnikov, Konstatin; ...

2017-07-08

In this study, we describe a new algorithm for solving multi-material diffusion problem when material interfaces are not aligned with the mesh. In this case interface reconstruction methods are used to construct approximate representation of interfaces between materials. They produce so-called multi-material cells, in which materials are represented by material polygons that contain only one material. The reconstructed interface is not continuous between cells. Finally, we suggest the new method for solving multi-material diffusion problems on such meshes and compare its performance with known homogenization methods.

Ion beam figuring technique used as final step in the manufacturing of the optics for the E-ELT

NASA Astrophysics Data System (ADS)

Ghigo, M.; Vecchi, G.; Basso, S.; Citterio, O.; Civitani, M.; Pareschi, G.; Sironi, G.

The INAF-Astronomical Observatory of Brera (INAF-OAB) is exploring the technical problems related to the ion beam figuring (IBF) of the Zerodur hexagonal mirrors (1.45 m corner to corner) of M1 for the European Extremely Large Telescope (E-ELT). As starting step a scaled down version mirror of the same material having size of 1 m corner to corner has been used to assess the relevant figuring problems. This specific mirror is spherical and has a radius of curvature of 3 m which allows a simple interferometric measurement setup. A mechanical support was designed to minimize its deformations due to gravity. The Ion Beam Figuring Facility used for this study has been recently completed in the Brera Observatory and has a figuring area of 170 cm x 140 cm. Aim of this study is the estimation and optimization of the time requested for the correction of the surface using also strategies to control the well-known thermal problems related to the Zerodur material. In this paper we report the results obtained figuring the 1 m corner-to-corner test segment.

Related Instructional Material for Electrical Apprentice Technical Training. Student Worksheets. Series C (Third Year). Revised to Meet 1978 Electrical Code.

ERIC Educational Resources Information Center

North Carolina State Dept. of Community Colleges, Raleigh.

Information sheets and student worksheets for twenty-five lesson plans designed for a third-year electrical apprentice technical training program are presented in this workbook. The information sheets provide summary information about the lesson topics and the worksheets contain problems to be solved and questions to be answered relating to each…

Related Instructional Material for Electrical Apprentice Technical Training. Student Worksheets. Series D (Fourth Year). Revised to Meet 1978 Electrical Code.

ERIC Educational Resources Information Center

North Carolina State Dept. of Community Colleges, Raleigh.

Information sheets and student worksheets for twenty-seven lesson plans designed for a fourth-year electrical apprentice technical training program are presented in this workbook. The information sheets provide summary information about the lesson topics and the worksheets contain problems to be solved and questions to be answered relating to each…

Sixty years of aeronautical research, 1917-1977. [Langley Research Center

NASA Technical Reports Server (NTRS)

Anderton, D. A.

1978-01-01

The history of Langley Research Center and its contributions to solving problems related to flight over the past six decades is recounted. Technical innovations described include those related to air craft construction materials, jet and rocket propulsion, flight testing and simulation, wind tunnel tests, noise reduction, supersonic flight, air traffic control, structural analysis, computational aerodynamics, and fuel efficiency.

Investigating Encrypted Material

NASA Astrophysics Data System (ADS)

McGrath, Niall; Gladyshev, Pavel; Kechadi, Tahar; Carthy, Joe

When encrypted material is discovered during a digital investigation and the investigator cannot decrypt the material then s/he is faced with the problem of how to determine the evidential value of the material. This research is proposing a methodology of extracting probative value from the encrypted file of a hybrid cryptosystem. The methodology also incorporates a technique for locating the original plaintext file. Since child pornography (KP) images and terrorist related information (TI) are transmitted in encrypted format the digital investigator must ask the question Cui Bono? - who benefits or who is the recipient? By doing this the scope of the digital investigation can be extended to reveal the intended recipient.

Federal Library Programs for Acquisition of Foreign Materials.

ERIC Educational Resources Information Center

Cylke, Frank Kurt

Sixteen libraries representing those agencies holding membership on the Federal Library Committee were surveyed to determine library foreign language or imprint holdings, acquisitions techniques, procedures and/or problems. Specific questions, relating to holdings, staff, budget and the acquisition, processing, reference and translation services…

INTERdependence Curriculum Aid.

ERIC Educational Resources Information Center

World Affairs Council of Philadelphia, PA.

Stressing global interdependence, this guide suggests resources, materials, and activities related to major world problems. Global interdependence is interpreted as connections between and among nations in areas of war and peace, human rights, environmental use, economics, and international law. The major objective is to help students understand…

Advanced numerical models and material characterisation techniques for composite materials subject to impact and shock wave loading

NASA Astrophysics Data System (ADS)

Clegg, R. A.; White, D. M.; Hayhurst, C.; Ridel, W.; Harwick, W.; Hiermaier, S.

2003-09-01

The development and validation of an advanced material model for orthotropic materials, such as fibre reinforced composites, is described. The model is specifically designed to facilitate the numerical simulation of impact and shock wave propagation through orthotropic materials and the prediction of subsequent material damage. Initial development of the model concentrated on correctly representing shock wave propagation in composite materials under high and hypervelocity impact conditions [1]. This work has now been extended to further concentrate on the development of improved numerical models and material characterisation techniques for the prediction of damage, including residual strength, in fibre reinforced composite materials. The work is focussed on Kevlar-epoxy however materials such as CFRP are also being considered. The paper describes our most recent activities in relation to the implementation of advanced material modelling options in this area. These enable refined non-liner directional characteristics of composite materials to be modelled, in addition to the correct thermodynamic response under shock wave loading. The numerical work is backed by an extensive experimental programme covering a wide range of static and dynamic tests to facilitate derivation of model input data and to validate the predicted material response. Finally, the capability of the developing composite material model is discussed in relation to a hypervelocity impact problem.

Influence of the recycled material percentage on the rheological behaviour of HDPE for injection moulding process.

PubMed

Javierre, C; Clavería, I; Ponz, L; Aísa, J; Fernández, A

2007-01-01

The amount of polymer material wasted during thermoplastic injection moulding is very high. It comes from both the feed system of the part, and parts necessary to set up the mould, as well as the scrap generated along the process due to quality problems. The residues are managed through polymer recycling that allows reuse of the materials in the manufacturing injection process. Recycling mills convert the parts into small pieces that are used as feed material for injection, by mixing the recycled feedstock in different percentages with raw material. This mixture of both raw and recycled material modifies material properties according to the percentage of recycled material introduced. Some of the properties affected by this modification are those related to rheologic behaviour, which strongly conditions the future injection moulding process. This paper analyzes the rheologic behaviour of material with different percentages of recycled material by means of a capillary rheometer, and evaluates the influence of the corresponding viscosity curves obtained on the injection moulding process, where small variations of parameters related to rheological behaviour, such as pressure or clamping force, can be critical to the viability and cost of the parts manufactured by injection moulding.

On the mechanics of stress analysis of fiber-reinforced composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, V.G.

A general mathematical formulation is developed for the three-dimensional inclusion and inhomogeneity problems, which are practically important in many engineering applications such as fiber pullout of reinforced composites, load transfer behavior in the stiffened structural components, and material defects and impurities existing in engineering materials. First, the displacement field (Green's function) for an elastic solid subjected to various distributions of ring loading is derived in closed form using the Papkovich-Neuber displacement potentials and the Hankel transforms. The Green's functions are used to derive the displacement and stress fields due to a finite cylindrical inclusion of prescribed dilatational eigenstrain such asmore » thermal expansion caused by an internal heat source. Unlike an elliptical inclusion, the interior stress field in the cylindrical inclusion is not uniform. Next, the three-dimensional inhomogeneity problem of a cylindrical fiber embedded in an infinite matrix of different material properties is considered to study load transfer of a finite fiber to an elastic medium. By using the equivalent inclusion method, the fiber is modeled as an inclusion with distributed eigenstrains of unknown strength, and the inhomogeneity problem can be treated as an equivalent inclusion problem. The eigenstrains are determined to simulate the disturbance due to the existing fiber. The equivalency of elastic field between inhomogeneity and inclusion problems leads to a set of integral equations. To solve the integral equations, the inclusion domain is discretized into a finite number of sub-inclusions with uniform eigenstrains, and the integral equations are reduced to a set of algebraic equations. The distributions of eigenstrains, interior stress field and axial force along the fiber are presented for various fiber lengths and the ratio of material properties of the fiber relative to the matrix.« less

A position-aware linear solid constitutive model for peridynamics

DOE PAGES

Mitchell, John A.; Silling, Stewart A.; Littlewood, David J.

2015-11-06

A position-aware linear solid (PALS) peridynamic constitutive model is proposed for isotropic elastic solids. The PALS model addresses problems that arise, in ordinary peridynamic material models such as the linear peridynamic solid (LPS), due to incomplete neighborhoods near the surface of a body. We improved model behavior in the vicinity of free surfaces through the application of two influence functions that correspond, respectively, to the volumetric and deviatoric parts of the deformation. Furthermore, the model is position-aware in that the influence functions vary over the body and reflect the proximity of each material point to free surfaces. Demonstration calculations onmore » simple benchmark problems show a sharp reduction in error relative to the LPS model.« less

A position-aware linear solid constitutive model for peridynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, John A.; Silling, Stewart A.; Littlewood, David J.

A position-aware linear solid (PALS) peridynamic constitutive model is proposed for isotropic elastic solids. The PALS model addresses problems that arise, in ordinary peridynamic material models such as the linear peridynamic solid (LPS), due to incomplete neighborhoods near the surface of a body. We improved model behavior in the vicinity of free surfaces through the application of two influence functions that correspond, respectively, to the volumetric and deviatoric parts of the deformation. Furthermore, the model is position-aware in that the influence functions vary over the body and reflect the proximity of each material point to free surfaces. Demonstration calculations onmore » simple benchmark problems show a sharp reduction in error relative to the LPS model.« less

International waste management fact book

DOE Office of Scientific and Technical Information (OSTI.GOV)

Amaya, J P; LaMarche, M N; Upton, J F

1997-10-01

Many countries around the world are faced with nuclear and environmental management problems similar to those being addressed by the US Department of Energy. The purpose of this Fact Book is to provide the latest information on US and international organizations, programs, activities and key personnel to promote mutual cooperation to solve these problems. Areas addressed include all aspects of closing the commercial and nuclear fuel cycle and managing the wastes and sites from defense-related, nuclear materials production programs.

Op weg naar een didactiek voor natuurkunde-experimenten op afstand : Ontwerp en evaluatie van een via internet uitvoerbaar experiment voor leerlingen uit het voortgezet onderwijs

NASA Astrophysics Data System (ADS)

Engelbarts, M. B. A.

2009-02-01

The subject of this thesis is a developmental study on “remote experimenting” in education. It concerns the development of a remote experiment that enables pre-university students to carry out a physics experiment at a distance via the internet. Remote experiments can offer several (practical) benefits when compared to conventional experiments but the desire to exploit these benefits put special demands on the design of the experiment, since the students might be conducting the experiment without a teacher in the vicinity. As a consequence of these demands it was decided to focus on exploring the possibilities and problems of remote experiments conducted in the absence of a teacher. The research was carried out in two cycles and focused on the development of a remote experiment that could be conducted autonomously by pre-university students to measure the speed of light in several media. This should answer the global question: What should a technically, as well as didactically, well-functioning remote experiment look like? The first cycle had an explorative character. It showed that technically the experiment already functioned quite well. However, many problems were observed concerning the content, and the way the students were tackling it. This led to two categories of recommendations. Concerning the content, the material should aim at making the students more aware of what they are doing and why they are doing it and several content related problems needed to be avoided. The second category of recommendations concerned the format of the material: the design and the working method. Special attention should be paid to designing a clear structure for the website and adding interaction and control, (feedback- and reflection facilities) to activate the students and guide them through the material. In the second research cycle these recommendations were followed by designing the material within the theoretical framework of the problem posing theory. A didactical structure was designed before writing the actual lesson material for the website describing the inter-related conceptual and content-related motivational pathway of the intended teaching-learning process. The lesson material was set up in such a way that the students are repeatedly confronted with a practical problem to solve and they play an active role in developing the method of measurement. Secondly, in an attempt to compensate for the absence of the teacher and support the teaching-learning process some format elements were developed and deployed like an automated question-, and feedback system that supported the students, activated them and gave them insight into their learning process and a ‘Where-am-I’-window that showed their current position within the material. This all had led to a technically as well as didactically well functioning remote experiment in which, at a global level, the line of reasoning was made explicit and recognizable for the students, and ad a local level was build up out of well connected successive activities and required the students to adopt an active attitude.

Degradation of sustainable mulch materials in two types of soil under laboratory conditions

NASA Astrophysics Data System (ADS)

Villena, Jaime; González, Sara; Moreno, Carmen; Aceituno, Patricia; Campos, Juan; Meco, Ramón; María Moreno, Marta

2017-04-01

Mulching is a technique used in cultivation worldwide, especially for vegetable crops, for reducing weed growth, minimising or eliminating soil erosion, and often for enhancing total yields. Manufactured plastic films, mainly polyethylene (PE), have been widely used for this purpose due to their excellent mechanical properties, light weight and relatively low prices in recent years. However, the use of PE is associated with serious environmental problems related to its petrochemical origin and its long shelf-life, which causes a waste problem in our crop fields. For this reason, the use of biodegradable mulch materials (biopolymers and papers) as alternative to PE is increasing nowadays, especially in organic farming. However, these materials can suffer an undesirable early degradation (and therefore not fulfilling their function successfully), greatly resulting from the type of soil. For this reason, this study aimed to analyse the degradation pattern of different mulch materials buried in two types of soils, clay and sand, under laboratory conditions (25°C, dark surroundings, constant humidity). The mulch materials used were: 1) black polyethylene (15 µm); black biopolymers (15 µm): 2) maize starch-based, 3) potato starch-based, 4) polylactic acid-based, 5) black paper, 85 g/m2. Periodically (every 15-20 days), the weight and surface loss of the different materials were recorded. The results indicate that mulch degradation was earlier and higher in the clay soil, especially in the paper and in the potato starch-based materials, followed by the maize starch-based mulch, while polylactic acid-based suffered the least and the latest degradation. Keywords: mulch, biodegradable, biopolymer, paper, degradation. Acknowledgements: the research was funded by Project RTA2011-00104-C04-03 from the INIA (Spanish Ministry of Economy and Competitiveness).

Modeling granular material flows: The angle of repose, fluidization and the cliff collapse problem

NASA Astrophysics Data System (ADS)

Holsapple, Keith A.

2013-07-01

I discuss theories of granular material flows, with application to granular flows on the earth and planets. There are two goals. First, there is a lingering belief of some that the standard continuum plasticity Mohr-Coulomb and/or Drucker-Prager models are not adequate for many large-scale granular flow problems. The stated reason for those beliefs is the fact that the final slopes of the run-outs in collapse, landslide problems, and large-scale cratering are well below the angle of repose of the material. That observation, combined with the supposition that in those models flow cannot occur with slopes less than the angle of repose, has led to a number of researchers suggesting a need for lubrication or fluidization mechanisms and modeling. That issue is investigated in detail and shown to be false. A complete analysis of slope failures according to the Mohr-Coulomb model is presented, with special attention to the relations between the angle of repose and slope failures. It is shown that slope failure can occur for slope angles both larger than and smaller than the angle of repose. Second, to study the details of landslide run-outs, finite-difference continuum code simulations of the prototypical cliff collapse problem, using the classical plasticity models, are presented, analyzed and compared to experiments. Although devoid of any additional fluidization models, those simulations match experiments in the literature extremely well. The dynamics of this problem introduces additional important features relating to the run-out and final slope angles. The vertical free surface begins to fall at the initial 90° and flow continues to a final slope less than 10°. The detail in the calculation is examined to show why flow persists at slope angles that appear to be less than the angle of repose. The motions include regions of solid-like, fluid-like, and gas-like flows without invoking any additional models.

Thermo-elasto-viscoplastic analysis of problems in extension and shear

NASA Technical Reports Server (NTRS)

Riff, R.; Simitses, G. J.

1987-01-01

The problems of extension and shear behavior of structural elements made of carbon steel and subjected to large thermomechanical loads are investigated. The analysis is based on nonlinear geometric and constitutive relations, and is expressed in a rate form. The material constitutive equations are capable of reproducing all nonisothermal, elasto-viscoplastic characteristics. The results of the test problems show that: (1) the formulation can accommodate very large strains and rotations; (2) the model incorporates the simplification associated with rate-insensitive elastic response without losing the ability to model a rate-temperature dependent yield strength and plasticity; and (3) the formulation does not display oscillatory behavior in the stresses for the simple shear problem.

Theoretical comparison of maser materials for a 32-GHz maser amplifier

NASA Technical Reports Server (NTRS)

Lyons, James R.

1988-01-01

The computational results of a comparison of maser materials for a 32 GHz maser amplifier are presented. The search for a better maser material is prompted by the relatively large amount of pump power required to sustain a population inversion in ruby at frequencies on the order of 30 GHz and above. The general requirements of a maser material and the specific problems with ruby are outlined. The spin Hamiltonian is used to calculate energy levels and transition probabilities for ruby and twelve other materials. A table is compiled of several attractive operating points for each of the materials analyzed. All the materials analyzed possess operating points that could be superior to ruby. To complete the evaluation of the materials, measurements of inversion ratio and pump power requirements must be made in the future.

Semantic Relations for Problem-Oriented Medical Records

PubMed Central

Uzuner, Ozlem; Mailoa, Jonathan; Ryan, Russell; Sibanda, Tawanda

2010-01-01

Summary Objective We describe semantic relation (SR) classification on medical discharge summaries. We focus on relations targeted to the creation of problem-oriented records. Thus, we define relations that involve the medical problems of patients. Methods and Materials We represent patients’ medical problems with their diseases and symptoms. We study the relations of patients’ problems with each other and with concepts that are identified as tests and treatments. We present an SR classifier that studies a corpus of patient records one sentence at a time. For all pairs of concepts that appear in a sentence, this SR classifier determines the relations between them. In doing so, the SR classifier takes advantage of surface, lexical, and syntactic features and uses these features as input to a support vector machine. We apply our SR classifier to two sets of medical discharge summaries, one obtained from the Beth Israel-Deaconess Medical Center (BIDMC), Boston, MA and the other from Partners Healthcare, Boston, MA. Results On the BIDMC corpus, our SR classifier achieves micro-averaged F-measures that range from 74% to 95% on the various relation types. On the Partners corpus, the micro-averaged F-measures on the various relation types range from 68% to 91%. Our experiments show that lexical features (in particular, tokens that occur between candidate concepts, which we refer to as inter-concept tokens) are very informative for relation classification in medical discharge summaries. Using only the inter-concept tokens in the corpus, our SR classifier can recognize 84% of the relations in the BIDMC corpus and 72% of the relations in the Partners corpus. Conclusion These results are promising for semantic indexing of medical records. They imply that we can take advantage of lexical patterns in discharge summaries for relation classification at a sentence level. PMID:20646918

Teaching Old French Literature to Undergraduates.

ERIC Educational Resources Information Center

Stewart, Harry E.

As a prelude to graduate-level work for French majors, medieval studies are proposed for undergraduate students. Problems inherent in the establishment of the undergraduate program are identified with some suggested solutions. Concepts related to historical grammar, teaching materials, literature, and linguistics are developed. A logical course…

Space and Atmospheric Environments

NASA Technical Reports Server (NTRS)

Barth, Janet L.; Day, John H. (Technical Monitor)

2002-01-01

This viewgraph presentation provides information on space environments and the protection of materials and structures from their harsh conditions. Space environments are complex, and the complexity of spacecraft systems is increasing. Design accommodation must be realistic. Environmental problems can be limited at low cost relative to spacecraft cost.

Stress and the Organization.

ERIC Educational Resources Information Center

Davis, Richard H., Ed.

The proceedings of a conference on stress and the organization, sponsored by the Business Institute in Gerontology, are presented. The materials address the following areas of concern related to the problem of stress, including: (1) physiology and psychological effects; (2) organization-induced stress and its manifestations; (3) mid-life…

Mold-Resistant Construction.

ERIC Educational Resources Information Center

Huckabee, Christopher

2003-01-01

Asserts that one of the surest ways to prevent indoor air quality and mold issues is to use preventive construction materials, discussing typical resistance to dealing with mold problems (usually budget-related) and describing mold-resistant construction, which uses concrete masonry, brick, and stone and is intended to withstand inevitable…

Conservation of Photographic Print Collections.

ERIC Educational Resources Information Center

Swan, Alice

1981-01-01

Provides specific information on varying photographic materials and processes to aid archivists and curators in preserving photograph collections. Preservation problems related to major types of silver prints on paper (salt, albumen, collodion, gelatin) and to the silver image (oxidation, silver sulfide) are covered. Twenty references are cited.…

Healthy Buildings?

ERIC Educational Resources Information Center

Grubb, Deborah

Health problems related to school buildings can be categorized in five major areas: sick-building syndrome; health-threatening building materials; environmental hazards such as radon gas and asbestos; lead poisoning; and poor indoor air quality due to smoke, chemicals, and other pollutants. This paper provides an overview of these areas,…

Librarians and Teaching Faculty: Partners in Bibliographic Instruction.

ERIC Educational Resources Information Center

Carlson, David; Miller, Ruth H.

1984-01-01

This paper focuses on critical factors regarding the effectiveness of the course-related or course-integrated mode of bibliographic instruction: administrative problems (cost in time and personnel, coordination and scheduling materials development); critical role of faculty; consistency of instruction; transference of library knowledge from one…

Evaluation of the Interactionist Model of Socioeconomic Status and Problem Behavior: A Developmental Cascade across Generations

PubMed Central

Martin, Monica J.; Conger, Rand D.; Schofield, Thomas J.; Dogan, Shannon J.; Widaman, Keith F.; Donnellan, M. Brent; Neppl, Tricia K.

2010-01-01

The current multigenerational study evaluates the utility of the Interactionist Model of Socioeconomic Influence on human development (IMSI) in explaining problem behaviors across generations. The IMSI proposes that the association between socioeconomic status (SES) and human development involves a dynamic interplay that includes both social causation (SES influences human development) and social selection (individual characteristics affect SES). As part of the developmental cascade proposed by the IMSI, the findings from this investigation showed that G1 adolescent problem behavior predicted later G1 SES, family stress, and parental emotional investments, as well as the next generation of children's problem behavior. These results are consistent with a social selection view. Consistent with the social causation perspective, we found a significant relation between G1 SES and family stress, and in turn, family stress predicted G2 problem behavior. Finally, G1 adult SES predicted both material and emotional investments in the G2 child. In turn, emotional investments predicted G2 problem behavior, as did material investments. Some of the predicted pathways varied by G1 parent gender. The results are consistent with the view that processes of both social selection and social causation account for the association between SES and human development. PMID:20576188

A trans-phase granular continuum relation and its use in simulation

NASA Astrophysics Data System (ADS)

Kamrin, Ken; Dunatunga, Sachith; Askari, Hesam

The ability to model a large granular system as a continuum would offer tremendous benefits in computation time compared to discrete particle methods. However, two infamous problems arise in the pursuit of this vision: (i) the constitutive relation for granular materials is still unclear and hotly debated, and (ii) a model and corresponding numerical method must wear ``many hats'' as, in general circumstances, it must be able to capture and accurately represent the material as it crosses through its collisional, dense-flowing, and solid-like states. Here we present a minimal trans-phase model, merging an elastic response beneath a fictional yield criterion, a mu(I) rheology for liquid-like flow above the static yield criterion, and a disconnection rule to model separation of the grains into a low-temperature gas. We simulate our model with a meshless method (in high strain/mixing cases) and the finite-element method. It is able to match experimental data in many geometries, including collapsing columns, impact on granular beds, draining silos, and granular drag problems.

Proficiency Testing for Evaluating Aerospace Materials Test Anomalies

NASA Technical Reports Server (NTRS)

Hirsch, D.; Motto, S.; Peyton, S.; Beeson, H.

2006-01-01

ASTM G 86 and ASTM G 74 are commonly used to evaluate materials susceptibility to ignition in liquid and gaseous oxygen systems. However, the methods have been known for their lack of repeatability. The inherent problems identified with the test logic would either not allow precise identification or the magnitude of problems related to running the tests, such as lack of consistency of systems performance, lack of adherence to procedures, etc. Excessive variability leads to increasing instances of accepting the null hypothesis erroneously, and so to the false logical deduction that problems are nonexistent when they really do exist. This paper attempts to develop and recommend an approach that could lead to increased accuracy in problem diagnostics by using the 50% reactivity point, which has been shown to be more repeatable. The initial tests conducted indicate that PTFE and Viton A (for pneumatic impact) and Buna S (for mechanical impact) would be good choices for additional testing and consideration for inter-laboratory evaluations. The approach presented could also be used to evaluate variable effects with increased confidence and tolerance optimization.

Establishing mesh topology in multi-material cells: enabling technology for robust and accurate multi-material simulations

DOE PAGES

Kikinzon, Evgeny; Shashkov, Mikhail Jurievich; Garimella, Rao Veerabhadra

2018-05-29

Real world problems are typically multi-material, combining materials such as gases, liquids and solids that have very different properties. The material interfaces may be fixed in time or can be a part of the solution, as in fluid-structure interactions or air-water dynamics, and therefore move and change shape. In such problems the computational mesh may be non-conformal to interfaces due to complexity of these interfaces, presence of small fractions of materials, or because the mesh does not move with the flow, as in the arbitrary Lagrangian–Eulerian (ALE) methods. In order to solve problems of interest on such meshes, interface reconstructionmore » methods are usually used to recover an approximation of material regions within the cells. For a cell intersecting multiple material regions, these approximations of contained subregions can be considered as single-material subcells in a local mesh that we call a minimesh. In this paper, we discuss some of the requirements that discretization methods have on topological information in the resulting hierarchical meshes and present an approach that allows incorporating the buildup of sufficiently detailed topology into the nested dissections based PLIC-type reconstruction algorithms (e.g. Volume-of-Fluid, Moment-of-Fluid) in an efficient and robust manner. Specifically, we describe the X-MOF interface reconstruction algorithm in 2D, which extends the Moment-Of-Fluid (MOF) method to include the topology of minimeshes created inside of multi-material cells and parent-child relations between corresponding mesh entities on different hierarchy levels. X-MOF retains the property of being local to a cell and not requiring external communication, which makes it suitable for massively parallel applications. Here, we demonstrate some scaling results for the X-MOF implementation in Tangram, a modern interface reconstruction framework for exascale computing.« less

Establishing mesh topology in multi-material cells: enabling technology for robust and accurate multi-material simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kikinzon, Evgeny; Shashkov, Mikhail Jurievich; Garimella, Rao Veerabhadra

Real world problems are typically multi-material, combining materials such as gases, liquids and solids that have very different properties. The material interfaces may be fixed in time or can be a part of the solution, as in fluid-structure interactions or air-water dynamics, and therefore move and change shape. In such problems the computational mesh may be non-conformal to interfaces due to complexity of these interfaces, presence of small fractions of materials, or because the mesh does not move with the flow, as in the arbitrary Lagrangian–Eulerian (ALE) methods. In order to solve problems of interest on such meshes, interface reconstructionmore » methods are usually used to recover an approximation of material regions within the cells. For a cell intersecting multiple material regions, these approximations of contained subregions can be considered as single-material subcells in a local mesh that we call a minimesh. In this paper, we discuss some of the requirements that discretization methods have on topological information in the resulting hierarchical meshes and present an approach that allows incorporating the buildup of sufficiently detailed topology into the nested dissections based PLIC-type reconstruction algorithms (e.g. Volume-of-Fluid, Moment-of-Fluid) in an efficient and robust manner. Specifically, we describe the X-MOF interface reconstruction algorithm in 2D, which extends the Moment-Of-Fluid (MOF) method to include the topology of minimeshes created inside of multi-material cells and parent-child relations between corresponding mesh entities on different hierarchy levels. X-MOF retains the property of being local to a cell and not requiring external communication, which makes it suitable for massively parallel applications. Here, we demonstrate some scaling results for the X-MOF implementation in Tangram, a modern interface reconstruction framework for exascale computing.« less

High damping Al-Fe-Mo-Si/Zn-Al composites produced by rapidly solidified powder metallurgy process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, P.Y.; Dai, S.L.; Chai, S.C.

2000-05-10

The metallic materials commonly used in aircraft and aerospace fields, such as aluminum and titanium alloys, steels, etc., show extremely low damping capacity (usually of the order of or less than 10{sup {minus}3}). Thus, some problems related to vibration may emerge and influence the reliability, safety and life of airplanes, satellites, etc. It has been reported that almost two thirds of errors for rockets and satellites are related to vibration and noise. One effective way to solve these vibration-related problems is to adopt high damping metallic materials. Conventional high damping alloys exhibit damping capacity above 10{sup {minus}2}, however, their densitiesmore » are usually great than 5 x 10{sup 3} kg m{sup {minus}3}, or their strengths are less than 200 MPa (for alloys based on dislocation damping), making them impossible to be applied to aircraft and aerospace areas. Recently, some low-density high-damping metal/metal composites based on aluminum and high damping alloys have been developed in Beijing Institute of Aeronautical Materials (BIAM) by the rapidly solidified power metallurgy process. This paper aims to report the properties of the composites based on a high temperature Al-Fe-Mo-Si alloy and a high damping Zn-Al alloy, and compare them with that of 2618-T61 alloy produced by the ingot metallurgy process.« less

The Effect of Stochastic Perturbation of Fuel Distribution on the Criticality of a One Speed Reactor and the Development of Multi-Material Multinomial Line Statistics

NASA Technical Reports Server (NTRS)

Jahshan, S. N.; Singleterry, R. C.

2001-01-01

The effect of random fuel redistribution on the eigenvalue of a one-speed reactor is investigated. An ensemble of such reactors that are identical to a homogeneous reference critical reactor except for the fissile isotope density distribution is constructed such that it meets a set of well-posed redistribution requirements. The average eigenvalue, , is evaluated when the total fissile loading per ensemble element, or realization, is conserved. The perturbation is proven to increase the reactor criticality on average when it is uniformly distributed. The various causes of the change in reactivity, and their relative effects are identified and ranked. From this, a path towards identifying the causes. and relative effects of reactivity fluctuations for the energy dependent problem is pointed to. The perturbation method of using multinomial distributions for representing the perturbed reactor is developed. This method has some advantages that can be of use in other stochastic problems. Finally, some of the features of this perturbation problem are related to other techniques that have been used for addressing similar problems.

Spatial reasoning to determine stream network from LANDSAT imagery

NASA Technical Reports Server (NTRS)

Haralick, R. M.; Wang, S.; Elliott, D. B.

1983-01-01

In LANDSAT imagery, spectral and spatial information can be used to detect the drainage network as well as the relative elevation model in mountainous terrain. To do this, mixed information of material reflectance in the original LANDSAT imagery must be separated. From the material reflectance information, big visible rivers can be detected. From the topographic modulation information, ridges and valleys can be detected and assigned relative elevations. A complete elevation model can be generated by interpolating values for nonridge and non-valley pixels. The small streams not detectable from material reflectance information can be located in the valleys with flow direction known from the elevation model. Finally, the flow directions of big visible rivers can be inferred by solving a consistent labeling problem based on a set of spatial reasoning constraints.

Related Instructional Material for Electrical Apprentice Technical Training. Student Worksheets. Series No. A (First Year). Revised to Meet 1978 Electrical Code.

ERIC Educational Resources Information Center

North Carolina State Dept. of Community Colleges, Raleigh.

Information sheets and student worksheets for thirty-six lessons designed for a first-year electrical apprentice technical training program are presented in this workbook. The information sheets provide summary information about the lesson topics and the worksheets contain problems to be solved and questions to be answered relating to each lesson.…

Related Instructional Material for Electrical Apprentice Technical Training. Student Worksheets. Series No. B (Second Year). Revised to Meet 1978 Electrical Code.

ERIC Educational Resources Information Center

North Carolina State Dept. of Community Colleges, Raleigh.

Information sheets and student worksheets for twenty-eight lesson plans designed for a second-year electrical apprentice technical training program are presented in this workbook. The information sheets provide summary information about the lesson topics and the worksheets contain problems to be solved and questions to be answered relating to each…

Preparation of calibration materials for microanalysis of Ti minerals by direct fusion of synthetic and natural materials: experience with LA-ICP-MS analysis of some important minor and trace elements in ilmenite and rutile.

PubMed

Odegård, M; Mansfeld, J; Dundas, S H

2001-08-01

Calibration materials for microanalysis of Ti minerals have been prepared by direct fusion of synthetic and natural materials by resistance heating in high-purity graphite electrodes. Synthetic materials were FeTiO3 and TiO2 reagents doped with minor and trace elements; CRMs for ilmenite, rutile, and a Ti-rich magnetite were used as natural materials. Problems occurred during fusion of Fe2O3-rich materials, because at atmospheric pressure Fe2O3 decomposes into Fe3O4 and O2 at 1462 degrees C. An alternative fusion technique under pressure was tested, but the resulting materials were characterized by extensive segregation and development of separate phases. Fe2O3-rich materials were therefore fused below this temperature, resulting in a form of sintering, without conversion of the materials into amorphous glasses. The fused materials were studied by optical microscopy and EPMA, and tested as calibration materials by inductively coupled plasma mass spectrometry, equipped with laser ablation for sample introduction (LA-ICP-MS). It was demonstrated that calibration curves based on materials of rutile composition, within normal analytical uncertainty, generally coincide with calibration curves based on materials of ilmenite composition. It is, therefore, concluded that LA-ICP-MS analysis of Ti minerals can with advantage be based exclusively on calibration materials prepared for rutile, thereby avoiding the special fusion problems related to oxide mixtures of ilmenite composition. It is documented that sintered materials were in good overall agreement with homogeneous glass materials, an observation that indicates that in other situations also sintered mineral concentrates might be a useful alternative for instrument calibration, e.g. as alternative to pressed powders.

Shock waves simulated using the dual domain material point method combined with molecular dynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Duan Z.; Dhakal, Tilak Raj

Here in this work we combine the dual domain material point method with molecular dynamics in an attempt to create a multiscale numerical method to simulate materials undergoing large deformations with high strain rates. In these types of problems, the material is often in a thermodynamically nonequilibrium state, and conventional constitutive relations or equations of state are often not available. In this method, the closure quantities, such as stress, at each material point are calculated from a molecular dynamics simulation of a group of atoms surrounding the material point. Rather than restricting the multiscale simulation in a small spatial region,more » such as phase interfaces, or crack tips, this multiscale method can be used to consider nonequilibrium thermodynamic effects in a macroscopic domain. This method takes the advantage that the material points only communicate with mesh nodes, not among themselves; therefore molecular dynamics simulations for material points can be performed independently in parallel. The dual domain material point method is chosen for this multiscale method because it can be used in history dependent problems with large deformation without generating numerical noise as material points move across cells, and also because of its convergence and conservation properties. In conclusion, to demonstrate the feasibility and accuracy of this method, we compare the results of a shock wave propagation in a cerium crystal calculated using the direct molecular dynamics simulation with the results from this combined multiscale calculation.« less

Shock waves simulated using the dual domain material point method combined with molecular dynamics

DOE PAGES

Zhang, Duan Z.; Dhakal, Tilak Raj

2017-01-17

Here in this work we combine the dual domain material point method with molecular dynamics in an attempt to create a multiscale numerical method to simulate materials undergoing large deformations with high strain rates. In these types of problems, the material is often in a thermodynamically nonequilibrium state, and conventional constitutive relations or equations of state are often not available. In this method, the closure quantities, such as stress, at each material point are calculated from a molecular dynamics simulation of a group of atoms surrounding the material point. Rather than restricting the multiscale simulation in a small spatial region,more » such as phase interfaces, or crack tips, this multiscale method can be used to consider nonequilibrium thermodynamic effects in a macroscopic domain. This method takes the advantage that the material points only communicate with mesh nodes, not among themselves; therefore molecular dynamics simulations for material points can be performed independently in parallel. The dual domain material point method is chosen for this multiscale method because it can be used in history dependent problems with large deformation without generating numerical noise as material points move across cells, and also because of its convergence and conservation properties. In conclusion, to demonstrate the feasibility and accuracy of this method, we compare the results of a shock wave propagation in a cerium crystal calculated using the direct molecular dynamics simulation with the results from this combined multiscale calculation.« less

Grout formulation for disposal of low-level and hazardous waste streams containing fluoride

DOEpatents

McDaniel, E.W.; Sams, T.L.; Tallent, O.K.

1987-06-02

A composition and related process for disposal of hazardous waste streams containing fluoride in cement-based materials is disclosed. the presence of fluoride in cement-based materials is disclosed. The presence of fluoride in waste materials acts as a set retarder and as a result, prevents cement-based grouts from setting. This problem is overcome by the present invention wherein calcium hydroxide is incorporated into the dry-solid portion of the grout mix. The calcium hydroxide renders the fluoride insoluble, allowing the grout to set up and immobilize all hazardous constituents of concern. 4 tabs.

A coupled problem of finite deformation and flow in porous media

NASA Astrophysics Data System (ADS)

Moussa, A. B.

1980-06-01

A theory for deformation and two phase flow in porous media was developed. Equations of balance of mass, momentum, moment of momentum and energy for each constituent were postulated. These led to equivalent balance equations for the mixture as a whole to which an entropy production inequality was also postulated. The formulation was then applied to the silage material. A constitutive theory was developed for the mixture. General appropriate constitutive assumptions were suggested and made to satisfy the axiom of material objectivity and entropy production inequality. Material incompressibility was defined and introduced into the general form of constitutive relations.

Polycaprolactone/glass bioabsorbable implant in a rabbit humerus fracture model.

PubMed

Lowry, K J; Hamson, K R; Bear, L; Peng, Y B; Calaluce, R; Evans, M L; Anglen, J O; Allen, W C

1997-09-15

Research in improved materials and methods for internal fixation has centered on internal fixators made of bioabsorbable materials such as polylactic acid, polyglycolic acid, and polyparadioxanone. These materials have two problems: the first is a postoperative complication related to a delayed inflammatory response; and the second is low strength characteristics. An alternative material developed to alleviate these problems is a composite of phosphate glass fibers embedded in the polymer polycaprolactone, referred to as PCL. In this study, intramedullary pins made of PCL were compared to stainless steel pins in a rabbit humerus osteotomy model. Specimens were harvested at 0, 6, and 12 weeks postoperatively, radiographs and mechanical testing to failure were performed at each time interval, and tissue was examined microscopically at 6 and 12 weeks. Histologic results showed PCL pins to be well tolerated with minimal inflammation around the pin. Mechanical testing revealed the PCL fixation to be weaker initially than the stainless steel fixation. There was significant stress shielding of stainless-steel-healed rabbit humeri when compared to the PCL/bone humeri. All osteotomies immobilized with PCL healed with abundant periosteal callus production.

Global Failure Modes in High Temperature Composite Structures

NASA Technical Reports Server (NTRS)

Knauss, W. G.

1998-01-01

Composite materials have been considered for many years as the major advance in the construction of energy efficient aerospace structures. Notable advances have been made in understanding the special design considerations that set composites apart from the usual "isotropic" engineering materials such as the metals. As a result, a number of significant engineering designs have been accomplished. However, one shortcoming of the currently favored composites is their relatively unforgiving behavior with respect to failure (brittleness) under seemingly mild impact conditions and large efforts are underway to rectify that situation, much along the lines of introducing thermoplastic matrix materials. Because of their relatively more pronounced (thermo) viscoelastic behavior these materials respond with "toughness" in fracture situations. From the point of view of applications requiring material strength, this property is highly desirable. This feature impacts several important and distinct engineering problems which have been' considered under this grant and cover the 1) effect of impact damage on structural (buckling) stability of composite panels, the 2) effect of time dependence on the progression of buckling instabilities, and the 3) evolution of damage and fracture at generic thickness discontinuities in structures. The latter topic has serious implications for structural stability problems (buckling failure in reinforced shell structures) as well as failure progression in stringer-reinforced shell structures. This grant has dealt with these issues. Polymer "toughness" is usually associated with uncrosslinked or thermo-plastic polymers. But, by comparison with their thermoset counterparts they tend to exhibit more pronounced time dependent material behavior; also, that time dependence can occur at lower temperatures which places restriction in the high temperature use of these "newer and tougher" materials that are not quite so serious with the thermoset matrix materials. From a structural point of view the implications of this material behavior are potentially severe in that structural failure characteristics are no longer readily observed in short term qualification tests so characteristic for aerospace structures built from typical engineering metals.

The NASA Materials Science Research Program: It's New Strategic Goals and Opportunities

NASA Technical Reports Server (NTRS)

Schlagheck, Ronald A.; Stagg, Elizabeth

2004-01-01

In the past year, the NASA s Office of Biological and Physical Research (OBPR) has formulated a long term plan to perform strategical and fundamental research bringing together physics, chemistry, biology, and engineering to solve problems needed for current and future agency mission goals. Materials Science is one of basic disciplines within the Enterprise s Division of Physical Sciences Research. The Materials Science Program participates to utilize effective use of International Space Station (ISS) and various world class ground laboratory facilities to solve new scientific and technology questions and transfer these results for public and agency benefits. The program has recently targeted new investigative research in strategic areas necessary to expand NASA knowledge base for exploration of the universe and some of these experiments will need access to the microgravity of space. The program is implementing a wide variety of traditional ground and flight based research related types of fundamental science related to materials crystallization, fundamental processing, and properties characterization in order to obtain basic understanding of various phenomena effects and relationships to the structures, processing, and properties of materials. , In addition new initiatives in radiation protection, materials for propulsion and In-space fabrication and repair focus on research helping the agency solve problems needed for future transportation into the solar system. A summary of the types and sources for this research is presented including those experiments planned for a low gravity environment. Areas to help expand the science basis for NASA future missions are described. An overview of the program is given including the scope of the current and future NASA Research Announcements with emphasis on new materials science initiatives. A description of the planned flight experiments to be conducted on the International Space Station program along with the planned facility class Materials Science Research Rack (MSRR) and Microgravity Glovebox (MSG) type investigations. Some initial results from the first three materials experiments are given.

Interdisciplinary optimum design. [of aerospace structures

NASA Technical Reports Server (NTRS)

Sobieszczanski-Sobieski, Jaroslaw; Haftka, Raphael T.

1986-01-01

Problems related to interdisciplinary interactions in the design of a complex engineering systems are examined with reference to aerospace applications. The interdisciplinary optimization problems examined include those dealing with controls and structures, materials and structures, control and stability, structure and aerodynamics, and structure and thermodynamics. The discussion is illustrated by the following specific applications: integrated aerodynamic/structural optimization of glider wing; optimization of an antenna parabolic dish structure for minimum weight and prescribed emitted signal gain; and a multilevel optimization study of a transport aircraft.

Tissue stimulator enclosure welding fixture

NASA Technical Reports Server (NTRS)

Mcclure, S. R.

1977-01-01

It was demonstrated that the thickness of the stimulator titanium enclosure is directly related to the battery recharge time cycle. Reduction of the titanium enclosure thickness from approximately 0.37 mm (0.015 inch) to 0.05 mm (0.002 inch) significantly reduced the recharge time cycle and thereby patient inconvenience. However, fabrication of titanium enclosures from the thinner material introduced problems in forming, holding, and welding that required improvement in state of the art shop practices. The procedures that were utilized to resolve these fabrication problems are described.

What's New in Software? Hot New Tool: The Hypertext.

ERIC Educational Resources Information Center

Hedley, Carolyn N.

1989-01-01

This article surveys recent developments in hypertext software, a highly interactive nonsequential reading/writing/database approach to research and teaching that allows paths to be created through related materials including text, graphics, video, and animation sources. Described are uses, advantages, and problems of hypertext. (PB)

Fossil Fuels.

ERIC Educational Resources Information Center

Crank, Ron

This instructional unit is one of 10 developed by students on various energy-related areas that deals specifically with fossil fuels. Some topics covered are historic facts, development of fuels, history of oil production, current and future trends of the oil industry, refining fossil fuels, and environmental problems. Material in each unit may…

Taking lentils out of their comfort zone

USDA-ARS?s Scientific Manuscript database

Lentil is grown in many parts of the world where the photoperiod and temperature prior to flowering differ dramatically. Cultivars from one region struggle to perform well in other regions due to problems related to phenology. This makes breeders reluctant to use un-adapted material in their crosse...

The Consequences of Including Seductive Details during Lecture

ERIC Educational Resources Information Center

Harp, Shannon F.; Maslich, Amy A.

2005-01-01

When text passages include seductive details (i.e., interesting, tangentially related adjuncts that are irrelevant to the lesson), students perform worse on recall (Garner, Gillingham, & White, 1989) and problem-solving tests (Harp & Mayer, 1997, 1998) than students reading the same material without seductive details. To determine whether…

Libraries and Learning.

ERIC Educational Resources Information Center

Gee, E. Gordon; Breivik, Patricia Senn

Quality education in an information society must include skills related to the accessing and evaluating of pertinent information for problem solving. Moving beyond the practice of using reserve material, lectures, and textbooks predominant in most college teaching today would be a step towards producing independent learners more likely to use the…

Homogenization models for 2-D grid structures

NASA Technical Reports Server (NTRS)

Banks, H. T.; Cioranescu, D.; Rebnord, D. A.

1992-01-01

In the past several years, we have pursued efforts related to the development of accurate models for the dynamics of flexible structures made of composite materials. Rather than viewing periodicity and sparseness as obstacles to be overcome, we exploit them to our advantage. We consider a variational problem on a domain that has large, periodically distributed holes. Using homogenization techniques we show that the solution to this problem is in some topology 'close' to the solution of a similar problem that holds on a much simpler domain. We study the behavior of the solution of the variational problem as the holes increase in number, but decrease in size in such a way that the total amount of material remains constant. The result is an equation that is in general more complex, but with a domain that is simply connected rather than perforated. We study the limit of the solution as the amount of material goes to zero. This second limit will, in most cases, retrieve much of the simplicity that was lost in the first limit without sacrificing the simplicity of the domain. Finally, we show that these results can be applied to the case of a vibrating Love-Kirchhoff plate with Kelvin-Voigt damping. We rely heavily on earlier results of (Du), (CS) for the static, undamped Love-Kirchhoff equation. Our efforts here result in a modification of those results to include both time dependence and Kelvin-Voigt damping.

Bamboo leaf ash as the stabilizer for soft soil treatment

NASA Astrophysics Data System (ADS)

Rahman, A. S. A.; Jais, I. B. M.; Sidek, N.; Ahmad, J.; Rosli, M. I. F.

2018-04-01

Soft soil is a type of soil that have the size of particle less than 0.063mm. The strength of the soft soil does not fulfil the requirement for construction. The present of soft soil at the construction site always give a lot of problems and issues to geotechnical sector. Soil settlement is one of the problems that related to soft soil. The determination of the soft soil physical characteristics will provide a detail description on its characteristic. Soft soil need to be treated in order to gain the standard strength for construction. One of the method to strengthen the soft soil is by using pozzolanic material as a treatment method for soft soil. Furthermore bamboo leaf ash is one of the newly founded materials that contain pozzolanic material. Any material that consist of Silicon Dioxide (SiO2) as the main component and followed by Aluminium Oxide (Al2O3) and Iron Oxide (Fe2O3) are consider as pozzolanic material. Bamboo leaf ash is mix with the cement as the treatment material. Bamboo leaf ash will react with the cement to produce additional cement binder. Thus, it will increase the soil strength and will ease the geotechnical sector to achieve high quality of construction product.

Space Station Freedom Toxic and Reactive Materials Handling

NASA Technical Reports Server (NTRS)

Baugher, Charles R. (Editor)

1990-01-01

Viable research in materials processing in space requires the utilization of a wide variety of chemicals and materials, many of which are considered toxic and/or highly reactive with other substances. A realistic view of the experiments which are most likely to be accomplished in the early Space Station phases are examined and design issues addressed which are related to their safe implementation. Included are discussions of materials research on Skylab, Spacelab, and the Shuttle mid-deck; overviews of early concepts for specialized Space Station systems designed to help contain potential problems; descriptions of industrial experience with ground-based research; and an overview of the state-of-the-art in contamination detection systems.

Vacuum stability testing of Apollo 15 Scientific Instrument Module (SIM) non-metallic materials and reversion of silicone rubber in a motor switch

NASA Technical Reports Server (NTRS)

Clancy, H. M.

1972-01-01

Vacuum stability screening tests were performed on the Apollo 15 Scientific Instrument Module (SIM) bay nonmetallic materials in accordance with the NASA document SP-R-0022. The testing was necessary to support the evaluation to determine the effect material outgassing contamination would have on the SIM bay optical lenses and sensing devices. The Apollo 15 SIM experiments were highly successful, therefore, it is assumed that contamination due to the outgassing of nonmetallic materials did not affect equipment operation. A related problem, the reversion of a silicone rubber grommet which affected an electrical motor switch operation is also reported.

Theoretical Problems in Materials Science

NASA Technical Reports Server (NTRS)

Langer, J. S.; Glicksman, M. E.

1985-01-01

Interactions between theoretical physics and material sciences to identify problems of common interest in which some of the powerful theoretical approaches developed for other branches of physics may be applied to problems in materials science are presented. A unique structure was identified in rapidly quenched Al-14% Mn. The material has long-range directed bonds with icosahedral symmetry which does not form a regular structure but instead forms an amorphous-like quasiperiodic structure. Finite volume fractions of second phase material is advanced and is coupled with nucleation theory to describe the formation and structure of precipitating phases in alloys. Application of the theory of pattern formation to the problem of dendrite formation is studied.

A loosely-coupled scheme for the interaction between a fluid, elastic structure and poroelastic material

NASA Astrophysics Data System (ADS)

Bukač, M.

2016-05-01

We model the interaction between an incompressible, viscous fluid, thin elastic structure and a poroelastic material. The poroelastic material is modeled using the Biot's equations of dynamic poroelasticity. The fluid, elastic structure and the poroelastic material are fully coupled, giving rise to a nonlinear, moving boundary problem with novel energy estimates. We present a modular, loosely coupled scheme where the original problem is split into the fluid sub-problem, elastic structure sub-problem and poroelasticity sub-problem. An energy estimate associated with the stability of the scheme is derived in the case where one of the coupling parameters, β, is equal to zero. We present numerical tests where we investigate the effects of the material properties of the poroelastic medium on the fluid flow. Our findings indicate that the flow patterns highly depend on the storativity of the poroelastic material and cannot be captured by considering fluid-structure interaction only.

Multi-scale calculation based on dual domain material point method combined with molecular dynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dhakal, Tilak Raj

This dissertation combines the dual domain material point method (DDMP) with molecular dynamics (MD) in an attempt to create a multi-scale numerical method to simulate materials undergoing large deformations with high strain rates. In these types of problems, the material is often in a thermodynamically non-equilibrium state, and conventional constitutive relations are often not available. In this method, the closure quantities, such as stress, at each material point are calculated from a MD simulation of a group of atoms surrounding the material point. Rather than restricting the multi-scale simulation in a small spatial region, such as phase interfaces, or crackmore » tips, this multi-scale method can be used to consider non-equilibrium thermodynamic e ects in a macroscopic domain. This method takes advantage that the material points only communicate with mesh nodes, not among themselves; therefore MD simulations for material points can be performed independently in parallel. First, using a one-dimensional shock problem as an example, the numerical properties of the original material point method (MPM), the generalized interpolation material point (GIMP) method, the convected particle domain interpolation (CPDI) method, and the DDMP method are investigated. Among these methods, only the DDMP method converges as the number of particles increases, but the large number of particles needed for convergence makes the method very expensive especially in our multi-scale method where we calculate stress in each material point using MD simulation. To improve DDMP, the sub-point method is introduced in this dissertation, which provides high quality numerical solutions with a very small number of particles. The multi-scale method based on DDMP with sub-points is successfully implemented for a one dimensional problem of shock wave propagation in a cerium crystal. The MD simulation to calculate stress in each material point is performed in GPU using CUDA to accelerate the computation. The numerical properties of the multiscale method are investigated as well as the results from this multi-scale calculation are compared of particles needed for convergence makes the method very expensive especially in our multi-scale method where we calculate stress in each material point using MD simulation. To improve DDMP, the sub-point method is introduced in this dissertation, which provides high quality numerical solutions with a very small number of particles. The multi-scale method based on DDMP with sub-points is successfully implemented for a one dimensional problem of shock wave propagation in a cerium crystal. The MD simulation to calculate stress in each material point is performed in GPU using CUDA to accelerate the computation. The numerical properties of the multiscale method are investigated as well as the results from this multi-scale calculation are compared with direct MD simulation results to demonstrate the feasibility of the method. Also, the multi-scale method is applied for a two dimensional problem of jet formation around copper notch under a strong impact.« less

Unintended Consequences: How Qualification Constrains Innovation

NASA Technical Reports Server (NTRS)

Brice, Craig A.

2011-01-01

The development and implementation of new materials and manufacturing processes for aerospace application is often hindered by the high cost and long time span associated with current qualification procedures. The data requirements necessary for material and process qualification are extensive and often require millions of dollars and multiple years to complete. Furthermore, these qualification data can become obsolete for even minor changes to the processing route. This burden is a serious impediment to the pursuit of revolutionary new materials and more affordable processing methods for air vehicle structures. The application of integrated computational materials engineering methods to this problem can help to reduce the barriers to rapid insertion of new materials and processes. By establishing predictive capability for the development of microstructural features in relation to processing and relating this to critical property characteristics, a streamlined approach to qualification is possible. This paper critically examines the advantages and challenges to a modeling-assisted qualification approach for aerospace structural materials. An example of how this approach might apply towards the emerging field of additive manufacturing is discussed in detail.

Reintegration after bone marrow transplantation.

PubMed

Baker, F; Zabora, J; Polland, A; Wingard, J

1999-01-01

This study examines the problems of bone marrow transplantation (BMT) survivors in returning to "normal" life in the community after BMT. Before being released from The Johns Hopkins Oncology Center, 84 recipients of BMT were interviewed regarding their quality of life and psychosocial adaptation. Survivors were reinterviewed at 6 months, and at 1 year post-BMT, producing considerable qualitative data regarding their problems in living. Eighty-four patients who had received BMT completed qualitative interviews and standardized measures before treatment, before the return home, and at 6 and 12 months post-BMT. The interviews were subjected to a content analysis methodology to establish units and categories to examine the body of material. Content analysis of these interviews from the first year after BMT identified three areas of psychosocial morbidity; 1) physical problems, which included fatigue, appearance, troubles in eating, and physical restrictions; 2) psychological problems, which included fears about the future, sense of loss of control, anxiety, and depression; and 3) community reintegration problems, which included difficulty in returning to former social roles, separation from home, family, and friends, difficulty in resuming social relations, dealing with stigmatization, problems with family and children, and financial and employment difficulties. Identification of these problems for BMT survivors can be used to guide the development of specific materials and services to prepare recipients of BMTs and their families for life after the transplant. These qualitative results can also be used to direct the development of assessment tools to identify potential patient and family problems.

An investigation into pilot and system response to critical in-flight events. Volume 2: Appendix

NASA Technical Reports Server (NTRS)

Rockwell, T. H.; Griffin, W. C.

1981-01-01

Materials relating to the study of pilot and system response to critical in-flight events (CIFE) are given. An annotated bibliography and a trip summary outline are presented, as are knowledge surveys with accompanying answer keys. Performance profiles of pilots and performance data from the simulations of CIFE's are given. The paper and pencil testing materials are reproduced. Conditions for the use of the additive model are discussed. A master summary of data for the destination diversion scenario is given. An interview with an aircraft mechanic demonstrates the feasibility of system problem diagnosis from a verbal description of symptoms and shows the information seeking and problem solving logic used by an expert to narrow the list of probable causes of aircraft failure.

A cylindrical shell with an arbitrarily oriented crack

NASA Technical Reports Server (NTRS)

Yahsi, O. S.; Erdogan, F.

1983-01-01

The general problem of a shallow shell with constant curvatures is considered. It is assumed that the shell contains an arbitrarily oriented through crack and the material is specially orthotropic. The nonsymmetric problem is solved for arbitrary self equilibrating crack surface tractions, which, added to an appropriate solution for an uncracked shell, would give the result for a cracked shell under most general loading conditions. The problem is reduced to a system to five singular integral equations in a set of unknown functions representing relative displacements and rotations on the crack surfaces. The stress state around the crack tip is asymptotically analyzed and it is shown that the results are identical to those obtained from the two dimensional in plane and antiplane elasticity solutions. The numerical results are given for a cylindrical shell containing an arbitrarily oriented through crack. Some sample results showing the effect of the Poisson's ratio and the material orthotropy are also presented. Previously annunced in STAR as N83-16783

Seal welded cast iron nuclear waste container

DOEpatents

Filippi, Arthur M.; Sprecace, Richard P.

1987-01-01

This invention identifies methods and articles designed to circumvent metallurgical problems associated with hermetically closing an all cast iron nuclear waste package by welding. It involves welding nickel-carbon alloy inserts which are bonded to the mating plug and main body components of the package. The welding inserts might be bonded in place during casting of the package components. When the waste package closure weld is made, the most severe thermal effects of the process are restricted to the nickel-carbon insert material which is far better able to accommodate them than is cast iron. Use of nickel-carbon weld inserts should eliminate any need for pre-weld and post-weld heat treatments which are a problem to apply to nuclear waste packages. Although the waste package closure weld approach described results in a dissimilar metal combination, the relative surface area of nickel-to-iron, their electrochemical relationship, and the presence of graphite in both materials will act to prevent any galvanic corrosion problem.

Nonlinear mechanical behavior of thermoplastic matrix materials for advanced composites

NASA Technical Reports Server (NTRS)

Arenz, R. J.; Landel, R. F.

1989-01-01

Two recent theories of nonlinear mechanical response are quantitatively compared and related to experimental data. Computer techniques are formulated to handle the numerical integration and iterative procedures needed to solve the associated sets of coupled nonlinear differential equations. Problems encountered during these formulations are discussed and some open questions described. Bearing in mind these cautions, the consequences of changing parameters that appear in the formulations on the resulting engineering properties are discussed. Hence, engineering approaches to the analysis of thermoplastic matrix material can be suggested.

The use of perineal massage in the second stage of labor and follow-up of postpartum perineal outcomes.

PubMed

Karaçam, Zekiye; Ekmen, Hatice; Calişir, Hüsniye

2012-01-01

Because perineal trauma causes both short- and long-term problems after labor, the high rate of episiotomies and spontaneous lacerations is an important women's health problem in Turkey. Our aim in this study was to investigate whether perineal massage during labor decreased perineal trauma and trauma-related problems. The study included 396 pregnant women who were giving birth for the first time, between March 2007 and February 2009, in Turkey. It can be concluded that perineal massage decreases the amount of suture material required for episiotomy and thereby the size of the episiotomy and the rate of episiotomies and lacerations.

The surface and through crack problems in layered orthotropic plates

NASA Technical Reports Server (NTRS)

Erdogan, Fazil; Wu, Binghua

1991-01-01

An analytical method is developed for a relatively accurate calculation of Stress Intensity Factors in a laminated orthotropic plate containing a through or part-through crack. The laminated plate is assumed to be under bending or membrane loading and the mode 1 problem is considered. First three transverse shear deformation plate theories (Mindlin's displacement based first-order theory, Reissner's stress-based first-order theory, and a simple-higher order theory due to Reddy) are reviewed and examined for homogeneous, laminated and heterogeneous orthotropic plates. Based on a general linear laminated plate theory, a method by which the stress intensity factors can be obtained in orthotropic laminated and heterogeneous plates with a through crack is developed. Examples are given for both symmetrically and unsymmetrically laminated plates and the effects of various material properties on the stress intensity factors are studied. In order to implement the line-spring model which is used later to study the surface crack problem, the corresponding plane elasticity problem of a two-bonded orthotropic plated containing a crack perpendicular to the interface is also considered. Three different crack profiles: an internal crack, an edge crack, and a crack terminating at the interface are considered. The effect of the different material combinations, geometries, and material orthotropy on the stress intensity factors and on the power of stress singularity for a crack terminating at the interface is fully examined. The Line Spring model of Rice and Levy is used for the part-through crack problem. The surface crack is assumed to lie in one of the two-layered laminated orthotropic plates due to the limitation of the available plane strain results. All problems considered are of the mixed boundary value type and are reduced to Cauchy type of singular integral equations which are then solved numerically.

Human Sexuality and Relationship Counseling: A Workshop for Paraprofessionals.

ERIC Educational Resources Information Center

Rosenman, Martin F.

A four-day workshop dealing with problems related to human sexuality and relationship counseling followed the assumption that impact and desensitization at the personal level increases the participants' ability to apply the material covered to their particular counseling setting. Initially, desensitization was facilitated through the use of…

Energy Factsheets: 1, 3-24.

ERIC Educational Resources Information Center

League of Women Voters of the U.S., Washington, DC.

This is a series of fact sheets, each two pages long, presenting information, reading suggestions, and discussion questions on energy topics. The first fact sheet relates energy to the environmental problems. It provides a short background statement, remarks from notable experts, and a short list of reading material. The other fact sheets are on…

Cooperative International Education. Background Paper I.

ERIC Educational Resources Information Center

Griffin, Willis H.; Spence, Ralph B.

A discussion of the problems involved in developing a valid program for cooperation in international education begins by stressing the distinction between education and schooling: the first an age-old experience derived from the whole culture, and the second a relatively new concept devoted to mastering material which someone has decided is…

Self-Paced Physics, Segments 24-27.

ERIC Educational Resources Information Center

New York Inst. of Tech., Old Westbury.

Four study segments of the Self-Paced Physics Course materials are presented in this fifth problems and solutions book used as a part of student course work. The subject matter is related to work in electric fields, potential differences, parallel plates, electric potential energies, potential gradients, capacitances, and capacitor circuits.…

Self-Paced Physics, Segments 37-40.

ERIC Educational Resources Information Center

New York Inst. of Tech., Old Westbury.

Four study segments of the Self-Paced Physics Course materials are presented in this eighth problems and solutions book used as a part of course assignments. The content is related to magnetic induction, Faraday's law, induced currents, Lenz's law, induced electromotive forces, time-varying magnetic fields, self-inductance, inductors,…

Recruiting & Retaining Women: A Self-Assessment Guide for Law Enforcement.

ERIC Educational Resources Information Center

Harrington, Penny E.

This document presents information, guidelines, and resource materials to help law enforcement administrators address issues related to recruiting and retaining women in law enforcement. Its 14 chapters contain the following sections: statement of the problem; legal issues; possible solutions, model policies, and practices; expert assistance,…

Perspectives for Teachers of Latin American Culture.

ERIC Educational Resources Information Center

Seelye, H. Ned, Ed.

Articles treating various aspects of the teaching of Hispanic culture at the secondary and junior high school levels are intended to improve methodology and facilitate the development of teacher-made instructional materials. An overview of the field relating problems and procedures in several areas is developed. Selections cover: (1) bilinguality,…

Tin Can Racer Derby.

ERIC Educational Resources Information Center

Milson, James L.

1986-01-01

Describes directions for constructing "racing" cars out of simple materials like spools and coffee cans. Discusses procedures for students to build cars, then to test and race them. Stresses that the activity allows for self-discovery of problem solving techniques and opportunities to discuss the scientific concepts related to the activity. (TW)

Cultural Diversity in the Workplace: A Look at the Library Science Literature.

ERIC Educational Resources Information Center

Gilton, Donna

1996-01-01

Lists books, articles, videos, studies, and other information in library science related to workplace recruitment and retention of people of African, Hispanic or Latino, Asian/Pacific, or Native American identification, descent, or heritage. Includes materials examining workplace problems for racial minorities and the inclusive organization.…

Intersectional Computer-Supported Collaboration in Business Writing: Learning through Challenged Performance

ERIC Educational Resources Information Center

Remley, Dirk

2009-01-01

Carter (2007) identifies four meta-genres associated with writing activities that can help students learn discipline-specific writing skills relative to standards within a given field: these include problem solving, empirical approaches to analysis, selection of sources to use within research, and production of materials that meet accepted…

Teaching Communication and Conflict as a Game

ERIC Educational Resources Information Center

Yoshimura, Christina G.

2017-01-01

Courses: Communication and Conflict. Objectives: Through the use of a game-based framework, students will build intrinsic motivation to engage with course material and course content, and will engage their critical-thinking, problem-solving, and communication skills in relation to conflict management over the length of the course. A list of…

The Descriptive Challenges of Fiber Art.

ERIC Educational Resources Information Center

Lunin, Lois F.

1990-01-01

A definition of fiber art, its history, materials and techniques, vocabularies, and creators and users of those vocabularies offer background for understanding the problems in preparing surrogates of this relatively recent art form for text and image databases. Four examples of fiber image information systems are described. (32 references) (EAM)

Self-Paced Physics, Segments 28-31.

ERIC Educational Resources Information Center

New York Inst. of Tech., Old Westbury.

Four study segments of the Self-Paced Physics Course materials are presented in this sixth problems and solutions book used as a part of student course work. The subject matter is related to electric currents, current densities, resistances, Ohm's law, voltages, Joule heating, electromotive forces, single loop circuits, series and parallel…

Acid Rain Materials for Classroom Use.

ERIC Educational Resources Information Center

Factor, Lance; Kooser, Robert G.

This booklet contains three separate papers suitable for use in an advanced high school or college chemistry course. The first paper provides background information on acids and bases. The second paper provides additional background information, focusing on certain aspects of atmospheric chemistry as it relates to the acid rain problem. An attempt…

Access to University Education in Nigeria: A Review

ERIC Educational Resources Information Center

Agboola, B. M.; Ofoegbu, F. I.

2010-01-01

Demand for university education has increased due to the recent innovations of universal, free and compulsory education at the basic and senior secondary education level. Education has been expanding very rapidly at all levels in Nigeria. However, there are serious problems related to quality, equity, unavailable human and material resources and…

Why Does Military Combat Experience Adversely Affect Marital Relations?

ERIC Educational Resources Information Center

Gimbel, Cynthia; Booth, Alan

1994-01-01

Describes investigation of ways in which combat decreases marital quality and stability. Results support three models: (1) factors propelling men into combat also make them poor marriage material; (2) combat causes problems that increase marital adversity; and (3) combat intensifies premilitary stress and antisocial behavior which then negatively…

Towards a More Realistic Business Curriculum.

ERIC Educational Resources Information Center

Han, H'tein

A college business course focusing on the opportunities, issues, problems, and challenges of doing business with companies in the Pacific Rim region is described. The course has two major components: classroom learning and field study. The classroom component includes reading large quantities of materials that relate to economies of the Pacific…

Reading in the Social Studies Classroom.

ERIC Educational Resources Information Center

Bullock, Terry L.; Hesse, Karl D.

This publication examines reading instruction techniques that can be used by teachers to diagnose and remedy students' weaknesses in reading social studies materials. There are four chapters. Chapter one discusses issues, including trends related to reading in the social studies and problems presented by social studies textbooks. Chapters two and…

Modifications of zein with isocyanates

USDA-ARS?s Scientific Manuscript database

Zein is the major storage protein in corn and a promising raw material for industrial products. However, for zein to reach its full commercial potential two main problems need to be overcome: its relatively high cost and its poor resistance to water. In this work, we modified zein with several isoc...

Bibliography on Speech, Hearing and Language in Relation to Mental Retardation, 1900-1968.

ERIC Educational Resources Information Center

Peins, Maryann

The bibliography lists materials dealing with the communicative behavior (speech, hearing, language) of the mentally retarded. Each entry is classified according to one or more of the following categories: speech and language behavior; assessment of speech and language; hearing (assessment, problems, rehabilitation, research); habilitation…

Self-Paced Physics, Segments 32-36.

ERIC Educational Resources Information Center

New York Inst. of Tech., Old Westbury.

Five study segments of the Self-Paced Physics Course materials are presented in this seventh problems and solutions book used as a part of student course work. The content is related to magnetic fields, magnetic moments, forces on charged particles in magnetic fields, electron volts, cyclotron, electronic charge to mass ratio, current-carrying…

Numerical-graphical method for describing the creep of damaged highly filled polymer materials

NASA Astrophysics Data System (ADS)

Bykov, D. L.; Martynova, E. D.; Mel'nikov, V. P.

2015-09-01

A method for describing the creep behavior until fracture of a highly filled polymer material previously damaged in preliminary tests is proposed. The constitutive relations are the relations of nonlinear endochronic theory of aging viscoelastic materials (NETAVEM) [1]. The numerical-graphical method for identifying the functions occurring in NETAVEM, which was proposed in [2] for describing loading processes at a constant strain rate, is used here for the first time in creep theory. We use the results of experiments with undamaged and preliminary damaged specimens under the action of the same constant tensile loads. The creep kernel is determined in experiments with an undamaged specimen. The reduced time function contained in NETAVEM is determined from the position of points corresponding to the same values of strain on the creep curves of the damaged and undamaged specimens. An integral equation is solved to obtain the aging function, and then the viscosity function is determined. The knowledge of all functions contained in the constitutive relations permits solving the creep problem for products manufactured from a highly filled polymer material.

Confrontation (A Human Relations Training Unit and Simulation Game for Teacher and Administrators in a Multi-Ethnic Elementary and High School). Description of Teacher Inservice Education Materials.

ERIC Educational Resources Information Center

National Education Association, Washington, DC. Project on Utilization of Inservice Education R & D Outcomes.

The inservice teacher and administrator education program described here is intended to make teachers aware of the problems they may encounter in a multicultural, multiethnic school setting. The inservice topic is human relations, with the subject of black/white confrontation the main focus. This descriptive report provides additional information…

Neutron-diffraction measurement of residual stresses in Al-Cu cold-cut welding

NASA Astrophysics Data System (ADS)

Fiori, F.; Marcantoni, M.

Usually, when it is necessary to join different materials with a large difference in their melting points, welding should be avoided. To overcome this problem we designed and built a device to obtain cold-cut welding, which is able to strongly decrease oxidation problems of the surfaces to be welded. Thanks to this device it is possible to achieve good joining between different pairs of materials (Al-Ti, Cu-Al, Cu-Al alloys) without reaching the material melting point. The mechanical and microstructural characterisation of the joining and the validation of its quality were obtained using several experimental methods. In particular, in this work neutron-diffraction experiments for the evaluation of residual stresses in Cu-Al junctions are described, carried out at the G5.2 diffractometer of LLB, Saclay. Neutron-diffraction results are presented and related to other experimental tests such as microstructural characterisation (through optical and scanning electron microscopy) and mechanical characterisation (tensile-strength tests) of the welded interface.

Passing waves from atomistic to continuum

NASA Astrophysics Data System (ADS)

Chen, Xiang; Diaz, Adrian; Xiong, Liming; McDowell, David L.; Chen, Youping

2018-02-01

Progress in the development of coupled atomistic-continuum methods for simulations of critical dynamic material behavior has been hampered by a spurious wave reflection problem at the atomistic-continuum interface. This problem is mainly caused by the difference in material descriptions between the atomistic and continuum models, which results in a mismatch in phonon dispersion relations. In this work, we introduce a new method based on atomistic dynamics of lattice coupled with a concurrent atomistic-continuum method to enable a full phonon representation in the continuum description. This permits the passage of short-wavelength, high-frequency phonon waves from the atomistic to continuum regions. The benchmark examples presented in this work demonstrate that the new scheme enables the passage of all allowable phonons through the atomistic-continuum interface; it also preserves the wave coherency and energy conservation after phonons transport across multiple atomistic-continuum interfaces. This work is the first step towards developing a concurrent atomistic-continuum simulation tool for non-equilibrium phonon-mediated thermal transport in materials with microstructural complexity.

Failure Study of Composite Materials by the Yeh-Stratton Criterion

NASA Technical Reports Server (NTRS)

Yeh, Hsien-Yang; Richards, W. Lance

1997-01-01

The newly developed Yeh-Stratton (Y-S) Strength Criterion was used to study the failure of composite materials with central holes and normal cracks. To evaluate the interaction parameters for the Y-S failure theory, it is necessary to perform several biaxial loading tests. However, it is indisputable that the inhomogeneous and anisotropic nature of composite materials have made their own contribution to the complication of the biaxial testing problem. To avoid the difficulties of performing many biaxial tests and still consider the effects of the interaction term in the Y-S Criterion, a simple modification of the Y-S Criterion was developed. The preliminary predictions by the modified Y-S Criterion were relatively conservative compared to the testing data. Thus, the modified Y-S Criterion could be used as a design tool. To further understand the composite failure problem, an investigation of the damage zone in front of the crack tip coupled with the Y-S Criterion is imperative.

Using Everyday Materials To Promote Problem Solving in Toddlers.

ERIC Educational Resources Information Center

Segatti, Laura; Brown-DuPaul, Judy; Keyes, Tracy L.

2003-01-01

Outlines benefits of and skills involved in problem solving. Details how an environment rich in materials that foster cause-and-effect or trial-and-error explorations promote cognitive development among toddlers. Offers examples of problem-solving experiences and lists materials for use in curriculum planning. Describes the teacher' role as one of…

Life skills, mathematical reasoning and critical thinking: a curriculum for the prevention of problem gambling.

PubMed

Turner, Nigel E; Macdonald, John; Somerset, Matthew

2008-09-01

Previous studies have shown that youth are two to three times more likely than adults to report gambling related problems. This paper reports on the development and pilot evaluation of a school-based problem gambling prevention curriculum. The prevention program focused on problem gambling awareness and self-monitoring skills, coping skills, and knowledge of the nature of random events. The results of a controlled experiment evaluating the students learning from the program are reported. We found significant improvement in the students' knowledge of random events, knowledge of problem gambling awareness and self-monitoring, and knowledge of coping skills. The results suggest that knowledge based material on random events, problem gambling awareness and self-monitoring skills, and coping skills can be taught. Future development of the curriculum will focus on content to expand the students' coping skill options.

Integrated Force Method Solution to Indeterminate Structural Mechanics Problems

NASA Technical Reports Server (NTRS)

Patnaik, Surya N.; Hopkins, Dale A.; Halford, Gary R.

2004-01-01

Strength of materials problems have been classified into determinate and indeterminate problems. Determinate analysis primarily based on the equilibrium concept is well understood. Solutions of indeterminate problems required additional compatibility conditions, and its comprehension was not exclusive. A solution to indeterminate problem is generated by manipulating the equilibrium concept, either by rewriting in the displacement variables or through the cutting and closing gap technique of the redundant force method. Compatibility improvisation has made analysis cumbersome. The authors have researched and understood the compatibility theory. Solutions can be generated with equal emphasis on the equilibrium and compatibility concepts. This technique is called the Integrated Force Method (IFM). Forces are the primary unknowns of IFM. Displacements are back-calculated from forces. IFM equations are manipulated to obtain the Dual Integrated Force Method (IFMD). Displacement is the primary variable of IFMD and force is back-calculated. The subject is introduced through response variables: force, deformation, displacement; and underlying concepts: equilibrium equation, force deformation relation, deformation displacement relation, and compatibility condition. Mechanical load, temperature variation, and support settling are equally emphasized. The basic theory is discussed. A set of examples illustrate the new concepts. IFM and IFMD based finite element methods are introduced for simple problems.

The relationship between passibility, agency and social interaction and its relevance for research and pedagogy

NASA Astrophysics Data System (ADS)

Kirch, Susan A.; Ma, Jasmine Y.

2016-12-01

The interaction analysis presented by Kim and Roth examines nine students, their teachers, the learning task and materials in a mixed second and third grade science classroom during the school day. In the research narrative readers are introduced to two resourceful and creative groups of students as they work on a task assigned by their teacher—to cantilever a pizza box over the edge of a student desk. Readers are given glimpses (through images and transcripts) of the inventive ways each group solved the cantilever problem. Sometimes the children disregarded the design constraints, but even after compliance they managed to successfully solve the problem. The point of the learning task was not clearly stated, but readers are told the unit focused on investigating forces, forces in equilibrium, and structures as well as different forces (push, pull, etc.), properties of materials, and the relations between weight and balance while building structures. Kim and Roth were specifically interested in using this session to investigate and resolve the problem of learning as described by socio-cultural theorists as, how does a learner orient toward a learning outcome when they cannot do that until they have learned it? To answer this question Kim and Roth argued that learners (in engineering design) learn when and because: (1) they are open to be affected by the responses of materials to student action (i.e. student and material agency and physical touch) (2) their bodies are endowed with the capacity to be affected (i.e. passibility), and (3) knowledge and understanding emerge as and in social relations first. In their analysis, Kim and Roth argued that knowledge and knowing-how depend on these three universal processes. The authors further theorized the concept of passibility. Included in their theory of passibility was the claim that passibility is necessary for agency. After reading this paper we found we had many questions about Kim and Roth's analysis, context, and assertions, but we decided to focus this forum response on the problem of the learner and the solutions posed by Kim and Roth as well as the proposed relationship between passibility and agency.

Printed circuit boards: a review on the perspective of sustainability.

PubMed

Canal Marques, André; Cabrera, José-María; Malfatti, Célia de Fraga

2013-12-15

Modern life increasingly requires newer equipments and more technology. In addition, the fact that society is highly consumerist makes the amount of discarded equipment as well as the amount of waste from the manufacture of new products increase at an alarming rate. Printed circuit boards, which form the basis of the electronics industry, are technological waste of difficult disposal whose recycling is complex and expensive due to the diversity of materials and components and their difficult separation. Currently, printed circuit boards have a fixing problem, which is migrating from traditional Pb-Sn alloys to lead-free alloys without definite choice. This replacement is an attempt to minimize the problem of Pb toxicity, but it does not change the problem of separation of the components for later reuse and/or recycling and leads to other problems, such as temperature rise, delamination, flaws, risks of mechanical shocks and the formation of "whiskers". This article presents a literature review on printed circuit boards, showing their structure and materials, the environmental problem related to the board, some the different alternatives for recycling, and some solutions that are being studied to reduce and/or replace the solder, in order to minimize the impact of solder on the printed circuit boards. Copyright © 2013 Elsevier Ltd. All rights reserved.

Tracing for the problem-solving ability in advanced calculus class based on modification of SAVI model at Universitas Negeri Semarang

NASA Astrophysics Data System (ADS)

Pujiastuti, E.; Waluya, B.; Mulyono

2018-03-01

There were many ways of solving the problem offered by the experts. The author combines various ways of solving the problem as a form of novelty. Among the learning model that was expected to support the growth of problem-solving skills was SAVI. The purpose, to obtain trace results from the analysis of the problem-solving ability of students in the Dual Integral material. The research method was a qualitative approach. Its activities include tests was filled with mathematical connections, observation, interviews, FGD, and triangulation. The results were: (1) some students were still experiencing difficulties in solving the problems. (2) The application of modification of SAVI learning model effective in supporting the growth of problem-solving abilities. (3) The strength of the students related to solving the problem, there were two students in the excellent category, there were three students in right classes and one student in the medium group.

[Discussion of some problems in the new centurial planning material the therapeutics of acupuncture and moxibustion].

PubMed

Yang, Yun-kuan; Hu, You-ping; Wang, Yan

2006-11-01

Some problems were found for argument in the teaching of The Therapeutics of Acupuncture & Moxibustion, the new centurial national advanced Chinese medical school's planning material, including errors in compiling, some concepts lacking definition, and some acupuncture treatment methods in the material deviating off clinical practice, etc.. Study on these problems so as to make the teaching material more perfect, more scientific, accurate and authoritative.

Potential for bed-material entrainment in selected streams of the Edwards Plateau - Edwards, Kimble, and Real Counties, Texas, and vicinity

USGS Publications Warehouse

Heitmuller, Franklin T.; Asquith, William H.

2008-01-01

The Texas Department of Transportation spends considerable money for maintenance and replacement of low-water crossings of streams in the Edwards Plateau in Central Texas as a result of damages caused in part by the transport of cobble- and gravel-sized bed material. An investigation of the problem at low-water crossings was made by the U.S. Geological Survey in cooperation with the Texas Department of Transportation, and in collaboration with Texas Tech University, Lamar University, and the University of Houston. The bed-material entrainment problem for low-water crossings occurs at two spatial scales - watershed scale and channel-reach scale. First, the relative abundance and activity of cobble- and gravel-sized bed material along a given channel reach becomes greater with increasingly steeper watershed slopes. Second, the stresses required to mobilize bed material at a location can be attributed to reach-scale hydraulic factors, including channel geometry and particle size. The frequency of entrainment generally increases with downstream distance, as a result of decreasing particle size and increased flood magnitudes. An average of 1 year occurs between flows that initially entrain bed material as large as the median particle size, and an average of 1.5 years occurs between flows that completely entrain bed material as large as the median particle size. The Froude numbers associated with initial and complete entrainment of bed material up to the median particle size approximately are 0.40 and 0.45, respectively.

Behavior of thin-walled beams made of advanced composite materials and incorporating non-classical effects

NASA Astrophysics Data System (ADS)

Librescu, Liviu; Song, Ohseop

1991-11-01

Several results concerning the refined theory of thin-walled beams of arbitrary closed cross-section incorporating nonclassical effects are presented. These effects are related both with the exotic properties characterizing the advanced composite material structures and the nonuniform torsional model. A special case of the general equations is used to study several problems of cantilevered thin-walled beams and to assess the influence of the incorporated effects. The results presented in this paper could be useful toward a more rational design of aeronautical or aerospace constructions, as well as of helicopter or tilt rotor blades constructed of advanced composite materials.

Research study on materials processing in space, experiment M512

NASA Technical Reports Server (NTRS)

Rubenstein, M.; Hopkins, R. H.; Kim, H. B.

1973-01-01

Gallium arsenide, a commercially valuable semiconductor, has been prepared from the melt (M.P. 1237C), by vapor growth, and by growth from metallic solutions. It has been established that growth from metallic solution can produce material with high, and perhaps with the highest possible, chemical homogeneity and crystalline perfection. Growth of GaAs from metallic solution can be performed at relatively low temperatures (about 600C) and is relatively insensitive to temperature fluctuations. However, this type of crystal growth is subject to the decided disadvantage that density induced convection currents may produce variations in rates of growth at a growing surface. This problem would be minimized under reduced gravity conditions.

Too easily lead? Health effects of gasoline additives.

PubMed Central

Menkes, D B; Fawcett, J P

1997-01-01

Octane-enhancing constituents of gasoline pose a number of health hazards. This paper considers the relative risks of metallic (lead, manganese), aromatic (e.g., benzene), and oxygenated additives in both industrialized and developing countries. Technological advances, particularly in industrialized countries, have allowed the progressive removal of lead from gasoline and the increased control of exhaust emissions. The developing world, by contrast, has relatively lax environmental standards and faces serious public health problems from vehicle exhaust and the rapid increase in automobile use. Financial obstacles to the modernization of refineries and vehicle fleets compound this problem and the developing world continues to import large quantities of lead additives and other hazardous materials. Progress in decreasing environmental health problems depends both on the adoption of international public health standards as well as efforts to decrease dependence on the private automobile for urban transport. Images Figure 1. Figure 2. PMID:9171982

An Integrated, Problem-Based Learning Material: The "Satellite" Module

ERIC Educational Resources Information Center

Selcuk, Gamze Sezgin; Emiroglu, Handan Byacioglu; Tarakci, Mehmet; Ozel, Mustafa

2011-01-01

The purpose of this study is to introduce a problem-based learning material, the Satellite Module, that has integrated some of the subjects included in the disciplines of physics and mathematics at an introductory level in undergraduate education. The reason why this modular and problem-based material has been developed is to enable students to…

Bounding solutions of geometrically nonlinear viscoelastic problems

NASA Technical Reports Server (NTRS)

Stubstad, J. M.; Simitses, G. J.

1985-01-01

Integral transform techniques, such as the Laplace transform, provide simple and direct methods for solving viscoelastic problems formulated within a context of linear material response and using linear measures for deformation. Application of the transform operator reduces the governing linear integro-differential equations to a set of algebraic relations between the transforms of the unknown functions, the viscoelastic operators, and the initial and boundary conditions. Inversion either directly or through the use of the appropriate convolution theorem, provides the time domain response once the unknown functions have been expressed in terms of sums, products or ratios of known transforms. When exact inversion is not possible approximate techniques may provide accurate results. The overall problem becomes substantially more complex when nonlinear effects must be included. Situations where a linear material constitutive law can still be productively employed but where the magnitude of the resulting time dependent deformations warrants the use of a nonlinear kinematic analysis are considered. The governing equations will be nonlinear integro-differential equations for this class of problems. Thus traditional as well as approximate techniques, such as cited above, cannot be employed since the transform of a nonlinear function is not explicitly expressible.

Bounding solutions of geometrically nonlinear viscoelastic problems

NASA Technical Reports Server (NTRS)

Stubstad, J. M.; Simitses, G. J.

1986-01-01

Integral transform techniques, such as the Laplace transform, provide simple and direct methods for solving viscoelastic problems formulated within a context of linear material response and using linear measures for deformation. Application of the transform operator reduces the governing linear integro-differential equations to a set of algebraic relations between the transforms of the unknown functions, the viscoelastic operators, and the initial and boundary conditions. Inversion either directly or through the use of the appropriate convolution theorem, provides the time domain response once the unknown functions have been expressed in terms of sums, products or ratios of known transforms. When exact inversion is not possible approximate techniques may provide accurate results. The overall problem becomes substantially more complex when nonlinear effects must be included. Situations where a linear material constitutive law can still be productively employed but where the magnitude of the resulting time dependent deformations warrants the use of a nonlinear kinematic analysis are considered. The governing equations will be nonlinear integro-differential equations for this class of problems. Thus traditional as well as approximate techniques, such as cited above, cannot be employed since the transform of a nonlinear function is not explicitly expressible.

Helmholtz and parabolic equation solutions to a benchmark problem in ocean acoustics.

PubMed

Larsson, Elisabeth; Abrahamsson, Leif

2003-05-01

The Helmholtz equation (HE) describes wave propagation in applications such as acoustics and electromagnetics. For realistic problems, solving the HE is often too expensive. Instead, approximations like the parabolic wave equation (PE) are used. For low-frequency shallow-water environments, one persistent problem is to assess the accuracy of the PE model. In this work, a recently developed HE solver that can handle a smoothly varying bathymetry, variable material properties, and layered materials, is used for an investigation of the errors in PE solutions. In the HE solver, a preconditioned Krylov subspace method is applied to the discretized equations. The preconditioner combines domain decomposition and fast transform techniques. A benchmark problem with upslope-downslope propagation over a penetrable lossy seamount is solved. The numerical experiments show that, for the same bathymetry, a soft and slow bottom gives very similar HE and PE solutions, whereas the PE model is far from accurate for a hard and fast bottom. A first attempt to estimate the error is made by computing the relative deviation from the energy balance for the PE solution. This measure gives an indication of the magnitude of the error, but cannot be used as a strict error bound.

User Interface Problems of a Nationwide Inpatient Information System: A Heuristic Evaluation

PubMed Central

Atashi, Alireza; Azizi, Amirabbas; Dadashi, Ali

2016-01-01

Summary Introduction While studies have shown that usability evaluation could uncover many design problems of health information systems, the usability of health information systems in developing countries using their native language is poorly studied. The objective of this study was to evaluate the usability of a nationwide inpatient information system used in many academic hospitals in Iran. Material and Methods Three trained usability evaluators independently evaluated the system using Nielsen’s 10 usability heuristics. The evaluators combined identified problems in a single list and independently rated the severity of the problems. We statistically compared the number and severity of problems identified by HIS experienced and non-experienced evaluators. Results A total of 158 usability problems were identified. After removing duplications 99 unique problems were left. The highest mismatch with usability principles was related to “Consistency and standards” heuristic (25%) and the lowest related to “Flexibility and efficiency of use” (4%). The average severity of problems ranged from 2.4 (Major problem) to 3.3 (Catastrophe problem). The experienced evaluator with HIS identified significantly more problems and gave higher severities to problems (p<0.02). Discussion Heuristic Evaluation identified a high number of usability problems in a widely used inpatient information system in many academic hospitals. These problems, if remain unsolved, may waste users’ and patients’ time, increase errors and finally threaten patient’s safety. Many of them can be fixed with simple redesign solutions such as using clear labels and better layouts. This study suggests conducting further studies to confirm the findings concerning effect of evaluator experience on the results of Heuristic Evaluation. PMID:27081409

Using enquiry in learning: from vision to reality in higher education.

PubMed

Horne, Maria; Woodhead, Kath; Morgan, Liz; Smithies, Lynda; Megson, Denise; Lyte, Geraldine

2007-02-01

This paper reports on the contribution of six nurse educators to embed enquiry-led learning in a pre-registration nursing programme. Their focus was to evaluate student and facilitator perspectives of a hybrid model of problem-based learning, a form of enquiry-based learning and to focus on facilitators' perceptions of its longer-term utility with large student groups. Problem-based learning is an established learning strategy in healthcare internationally; however, insufficient evidence of its effectiveness with large groups of pre-registration students exists. Fourth Generation Evaluation was used, applying the Nominal Group Technique and Focus Group interviews, for data collection. In total, four groups representing different branches of pre-registration students (n = 121) and 15 facilitators participated. Students identified seven strengths and six areas for development related to problem-based learning. Equally, analysis of facilitators' discussions revealed several themes related to strengths and challenges. The consensus was that using enquiry aided the development of independent learning and encouraged deeper exploration of nursing and allied subject material. However, problems and frustrations were identified in relation to large numbers of groups, group dynamics, room and library resources and personal development. The implications of these findings for longer-term utility with large student groups are discussed.

Several cases of work-related allergic contact dermatitis caused by isocyanates at a company manufacturing heat exchangers.

PubMed

Engfeldt, Malin; Isaksson, Marléne; Zimerson, Erik; Bruze, Magnus

2013-03-01

A 43-year-old woman was referred by her occupational health service with suspected occupational contact dermatitis. In connection with the investigation, a workplace visit was undertaken at her company, which used an adhesive based on pre-polymeric diphenylmethane diisocyanate in one of its units. During the visit, we became aware of six other employees with skin problems who were then referred to our department for investigation. To investigate the seven employees complaining about skin problems. Seven employees were patch tested with a baseline series, an isocyanate series, and a series with work material. Five of seven patients had occupational contact allergy. Four reacted to isocyanate-related test preparations, and one to a cleanser used at the workplace. Workplace visits constitute an important part of an occupational investigation, as they might give a broader picture of the problems at a company. In this case, it was found that 5 of 100 employees currently had or had previously had occupation-related skin problems. Owing to 'healthy worker selection', some of these patients might have been missed if we had not performed a full-scale workplace visit. © 2012 John Wiley & Sons A/S.

The profile of high school students’ scientific literacy on fluid dynamics

NASA Astrophysics Data System (ADS)

Parno; Yuliati, L.; Munfaridah, N.

2018-05-01

This study aims to describe the profile of scientific literacy of high school students on Fluid Dynamics materials. Scientific literacy is one of the ability to solve daily problems in accordance with the context of materials related to science and technology. The study was conducted on 90 high school students in Sumbawa using survey design. Data were collected using an instrument of scientific literacy for high school students on dynamic fluid materials. Data analysis was conducted descriptively to determine the students’ profile of scientific literacy. The results showed that high school students’ scientific literacy on Fluid Dynamics materials was in the low category. The highest average is obtained on indicators of scientific literacy i.e. the ability to interpret data and scientific evidence. The ability of scientific literacy is related to the mastery of concepts and learning experienced by students, therefore it is necessary to use learning that can trace this ability such as Science, Technology, Engineering, and Mathematics (STEM).

High temperature superconductor NB3Ga

NASA Technical Reports Server (NTRS)

Vieland, L. J.; Wicklund, A. W.

1973-01-01

The discovery of superconductivity at 20.3 K in the Nb-Ga system by applying chemical vapor deposition (CVD) techniques to the materials preparation problem is reported. Films on ceramic substrates have been grown with superconducting onsets of up to 20.3 K. Critical fields at 4.2 K in excess of 300 kG and alpha's of 1100,000 T-A/sq cm have been obtained. The results confirm that the outstanding properties of Nb-Ga are due to an equilibrium configuration of the system, namely, the stoichiometric A-15 compound Nb3Ga, which is stable at relatively low temperatures. Practical materials preparation problems center on the codeposition of an adjacent Nb5Ga3 phase and the requirement that the deposition temperature be low. Some ternary alloys were also prepared, with part of the Ga replaced by Sn, Sb, Al, or Ge.

Advances and trends in structural and solid mechanics; Proceedings of the Symposium, Washington, DC, October 4-7, 1982

NASA Technical Reports Server (NTRS)

Noor, A. K. (Editor); Housner, J. M.

1983-01-01

The mechanics of materials and material characterization are considered, taking into account micromechanics, the behavior of steel structures at elevated temperatures, and an anisotropic plasticity model for inelastic multiaxial cyclic deformation. Other topics explored are related to advances and trends in finite element technology, classical analytical techniques and their computer implementation, interactive computing and computational strategies for nonlinear problems, advances and trends in numerical analysis, database management systems and CAD/CAM, space structures and vehicle crashworthiness, beams, plates and fibrous composite structures, design-oriented analysis, artificial intelligence and optimization, contact problems, random waves, and lifetime prediction. Earthquake-resistant structures and other advanced structural applications are also discussed, giving attention to cumulative damage in steel structures subjected to earthquake ground motions, and a mixed domain analysis of nuclear containment structures using impulse functions.

Numerical simulation of damage evolution for ductile materials and mechanical properties study

NASA Astrophysics Data System (ADS)

El Amri, A.; Hanafi, I.; Haddou, M. E. Y.; Khamlichi, A.

2015-12-01

This paper presents results of a numerical modelling of ductile fracture and failure of elements made of 5182H111 aluminium alloys subjected to dynamic traction. The analysis was performed using Johnson-Cook model based on ABAQUS software. The modelling difficulty related to prediction of ductile fracture mainly arises because there is a tremendous span of length scales from the structural problem to the micro-mechanics problem governing the material separation process. This study has been used the experimental results to calibrate a simple crack propagation criteria for shell elements of which one has often been used in practical analyses. The performance of the proposed model is in general good and it is believed that the presented results and experimental-numerical calibration procedure can be of use in practical finite-element simulations.

Fabrication of Microcapsules for Dye-Doped Polymer-Dispersed Liquid Crystal-Based Smart Windows.

PubMed

Kim, Mingyun; Park, Kyun Joo; Seok, Seunghwan; Ok, Jong Min; Jung, Hee-Tae; Choe, Jaehoon; Kim, Do Hyun

2015-08-19

A dye-doped polymer-dispersed liquid crystal (PDLC) is an attractive material for application in smart windows. Smart windows using a PDLC can be operated simply and have a high contrast ratio compared to those of other devices that employed photochromic or thermochromic material. However, in conventional dye-doped PDLC methods, dye contamination can cause problems and has a limited degree of commercialization of electric smart windows. Here, we report on an approach to resolve dye-related problems by encapsulating the dye in monodispersed capsules. By encapsulation, a fabricated dye-doped PDLC had a contrast ratio of >120 at 600 nm. This fabrication method of encapsulating the dye in a core-shell structured microcapsule in a dye-doped PDLC device provides a practical platform for dye-doped PDLC-based smart windows.

Generation of Low-Energy High-Current Electron Beams in Plasma-Anode Electron Guns

NASA Astrophysics Data System (ADS)

Ozur, G. E.; Proskurovsky, D. I.

2018-01-01

This paper is a review of studies on the generation of low-energy high-current electron beams in electron guns with a plasma anode and an explosive-emission cathode. The problems related to the initiation of explosive electron emission under plasma and the formation and transport of high-current electron beams in plasma-filled systems are discussed consecutively. Considerable attention is given to the nonstationary effects that occur in the space charge layers of plasma. Emphasis is also placed on the problem of providing a uniform energy density distribution over the beam cross section, which is of critical importance in using electron beams of this type for surface treatment of materials. Examples of facilities based on low-energy high-current electron beam sources are presented and their applications in materials science and practice are discussed.

[Little known pages of the biography of Ia.V.Villie].

PubMed

Budko, A A; Shabunin, A V; Zhuravlev, D A

2005-05-01

On the base of complex study of archival data and available historical literature the stories connected with Yakov Vasilyevich Villie are discussed. The exact date of his death is given, the causes of existing contradictions are presented. Villie's relations with representatives of our medicine are described. The authors also discuss the problem, which was touched in the middle of XX century, i. e. the Villie's charge of espionage. Together with famous works of Russian authors the materials of foreign investigators devoted to this problem are used.

Vapor-delivered lubrication of steel-steel and steel-ceramic systems

NASA Astrophysics Data System (ADS)

Li, H.; Klaus, E. E.; Duda, J. L.

1993-04-01

Heavy-duty natural gas engines run hot and relatively dry. This provides lubricant and lubrication problems in the piston ring-cylinder and valve areas. A potential materials solution to this problem is the use of ceramic bearing surfaces. The objective of the project was the investigation of the wear characteristics and surface interactions of lubricants on ceramic bearing surfaces and to compare these results with the behavior of the same lubricants on steel surfaces. The temperature range of interest in these comparisons is 200 to 370 C using a four-ball wear tester.

Design of a Personnel and Training Information System for Educational R&D Personnel. Final Report.

ERIC Educational Resources Information Center

Hood, Paul D.; McCutchan, Nancy A.

The primary objective of this project was to design a system to provide information services that would fulfill the information requirements of federal planners, instructional material developers, training program directors and instructors, students, interns, employers, and practitioners concerned with problems relating to personnel and training…

Biodiversity, air quality and human health

Treesearch

David J. Nowak; Sarah Jovan; Christina Branquinho; Sofia Augusto; Manuel C. Ribeiro; Conor E. Kretsch

2015-01-01

Air pollution is a significant problem in cities across the world. It affects human health and well-being, ecosystem health, crops, climate, visibility and human-made materials. Health effects related to air pollution include its impact on the pulmonary, cardiac, vascular and neurological systems (Section 2). Trees affect air quality through a number of means (Section...

A Modified Bagnold-Type Wind Tunnel for Laboratory Use

ERIC Educational Resources Information Center

Logan, Alan

1975-01-01

Using the basic Bagnold design, a relatively inexpensive suction-type wind tunnel can be constructed for laboratory demonstration of sand-grain movement, ripple development, and other eolian processes. Its simple design provides no workshop problems and it can be made for a total cost in materials of approximately $225. (Author/CP)

Self-Paced Physics, Segments 19-23.

ERIC Educational Resources Information Center

New York Inst. of Tech., Old Westbury.

Five study segments of the Self-Paced Physics Course materials are presented in this fourth problems and solutions book used as a part of student course work. The subject matter is related to electric charges, insulators, Coulomb's law, electric fields, lines of force, solid angles, conductors, motion of charged particles, dipoles, electric flux,…

Is the Party Over? Cannabis and Juvenile Psychiatric Disorder: The Past 10 Years

ERIC Educational Resources Information Center

Rey, Joseph M.; Martin, Andres; Krabman, Peter

2004-01-01

Objective: To critically review cannabis research during the past 10 years in relation to rates of use, behavioral problems, and mental disorders in young people. Method: Studies published in English between 1994 and 2004 were identified through systematic searches of literature databases. The material was selectively reviewed focusing on child…

Light-Emitting Diodes: Solving Complex Problems

ERIC Educational Resources Information Center

Planinšic, Gorazd; Etkina, Eugenia

2015-01-01

This is the fourth paper in our Light-Emitting Diodes series. The series aims to create a systematic library of LED-based materials and to provide readers with the description of experiments and the pedagogical treatment that would help their students construct, test, and apply physics concepts and mathematical relations. The first paper provided…

78 FR 52219 - Notice of Acceptance of Renewal Application for Special Nuclear Materials License From Tennessee...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-22

... Order Imposing Procedures for Access to Sensitive Unclassified Non-Safeguards Information for Contention... related to the license renewal application using any of the following methods: Federal Rulemaking Web site..., select ``ADAMS Public Documents'' and then select ``Begin Web- based ADAMS Search.'' For problems with...

The Electrophysiological Correlates of Scientific Innovation Induced by Heuristic Information

ERIC Educational Resources Information Center

Luo, Junlong; Du, Xiumin; Tang, Xiaochen; Zhang, Entao; Li, Haijiang; Zhang, Qinglin

2013-01-01

In this study, novel and old scientific innovations (NSI and OSI) were selected as materials to explore the electrophysiological correlates of scientific innovation induced by heuristic information. Using event-related brain potentials (ERPs) to do so, college students solved NSI problems (for which they did not know the answers) and OSI problems…

Quantitation of aflatoxins from corn and other food related materials by direct analysis in real time - mass spectrometry (DART-MS)

USDA-ARS?s Scientific Manuscript database

Ambient ionization coupled to mass spectrometry continues to be applied to new analytical problems, facilitating the rapid and convenient analysis of a variety of analytes. Recently, demonstrations of ambient ionization mass spectrometry applied to quantitative analysis of mycotoxins have been shown...

Rolling-element bearings: A review of the state of the art

NASA Technical Reports Server (NTRS)

Anderson, W. J.; Zaretsky, E. V.

1973-01-01

Some of the research conducted which has brought rolling-element technology to its present state is discussed. Areas touched upon are material effects, processing variables, operating variables, design optimization, lubricant effects and lubrication methods. Finally, problem areas are discussed in relation to the present state-of-the-art and anticipated requirements.

Narrative Problems of Graphic Design History.

ERIC Educational Resources Information Center

Margolin, Victor

1994-01-01

Discusses three major accounts (by Philip Meggs, Enric Satue and Richard Hollis) of graphic design history. Notes that these texts address the history of graphic design, but each raises questions about what material to include, as well as how graphic design is both related to and distinct from other visual practices such as typography, art…

On Certain Aspects of the Problem of Adolescent Prostitution

ERIC Educational Resources Information Center

Ivanova, L.

2004-01-01

Adolescent prostitution is a particular social phenomenon characterized by the fact that adolescents (those under the age of eighteen), either females or males, engage more than once (at least two times) in extramarital sexual relations with a large number of people for some particular (material) consideration owing to social, economic,…

The North American Indian; A Bibliography of Community Development.

ERIC Educational Resources Information Center

Department of Housing and Urban Development, Washington, DC.

Developed by the Housing and Urban Development (HUD) library to meet the recent surge of interest in ethnic minorities and their problems, this annotated bibliography on community development relative to American Indians is divided into two parts. Utilization material published between 1969 and 1974, Part 1 presents 403 citations which are author…

Proxy-Produced Ethnographic Work: What Are the Problems, Issues, and Dilemmas Arising from Proxy-Ethnography?

ERIC Educational Resources Information Center

Martinussen, Marie; Højbjerg, Karin; Tamborg, Andreas Lindenskov

2018-01-01

This article addresses the implications of researcher-student cooperation in the production of empirical material. For the student to replace the experienced researcher and work under the researcher's supervision, we call such work proxy-produced ethnographic work. Although there are clear advantages, the specific relations and positions arising…

Perspectives on Transportation. [Student's Guide.] Preparing for Tomorrow's World.

ERIC Educational Resources Information Center

Iozzi, Louis A.; And Others

In this module students (grades 7-9) examine some of the many issues related to transportation and consider how different problems impact upon their lives and the lives of others. Student material consists of readings, dilemmas, and activities. These are presented in four sections focusing on land transportation, water transportation, air…

Synthesis of science and art: creating a new domestic world of sensual products

NASA Astrophysics Data System (ADS)

Thorpe, Chris; Friend, Clifford M.

1996-04-01

The creation of intelligent objects with sensual capabilities and caring personalities; objects which will share our domestic environments and our public spaces, is a vision at once both unnerving and inviting. As research into smart materials, intelligent material systems and the whole spectrum of related areas such as biomimetics, nano-technology and neural systems converge, we are now in a situation where in ten years intelligent objects could realize this lucid projection. The problem comes when we begin to look at the implications of such future object-environments. Our eagerness to solve the complex technical problems associated with the processing and manufacture of smart materials must be placed in the broader context of human considerations. If we are to realize their potential, and optimize the benefits which smart materials and intelligent material systems could bring to our quality of life, we must develop a new approach that is both technologically advanced and sympathetic towards human needs. An approach that is a synthesis of the objective reality sought through science and the irrational, emotional subjectivity embraced in the arts. This paper looks at the design of intelligent objects for the home, examining the role of design, the product interface and the relationship between objects and ourselves within the home environment.

Statistical methods for nuclear material management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowen W.M.; Bennett, C.A.

1988-12-01

This book is intended as a reference manual of statistical methodology for nuclear material management practitioners. It describes statistical methods currently or potentially important in nuclear material management, explains the choice of methods for specific applications, and provides examples of practical applications to nuclear material management problems. Together with the accompanying training manual, which contains fully worked out problems keyed to each chapter, this book can also be used as a textbook for courses in statistical methods for nuclear material management. It should provide increased understanding and guidance to help improve the application of statistical methods to nuclear material managementmore » problems.« less

Sociodemographic variables and social values: relationship with work-attendance problems in Brunei public- and private-sector employees

PubMed Central

Mundia, Lawrence; Mahalle, Salwa; Matzin, Rohani; Zakaria, Gamal Abdul Nasir; Abdullah, Nor Zaiham Midawati

2017-01-01

Objective The study investigated the degree to which selected sociodemographic variables and social values were related to work-attendance problems in a random sample of 860 Brunei public- and private-sector employees and the nature of this relationship. Materials and methods This quantitative study used the field-survey approach to administer research instruments directly to participants. This enabled the researchers to help participants who needed assistance in completing the measures properly, so as to increase the number of usable returns. Results Two sociodemographic variables (seeking help from a counselor/psychologist and marital status) correlated significantly with work attendance. Private-sector employees were more likely to have work-attendance problems than government workers. Both single and married employees and the chief wage earner in the household were more likely to have work-attendance issues to deal with compared to their counterparts. However, employees who sought help from a counselor/psychologist were far less likely to have work-attendance problems compared to those who did not get such help. The most significant social-value correlates with work-attendance problems were interpersonal communication, employer–employee relationship, work-stress problems, self-presentation, self-regulation, self-direction, and interpersonal trust. Self-regulation, self-direction, and satisfaction with work-related achievements significantly predicted work-attendance problems positively, while interpersonal communication problems and work-stress problems predicted work-attendance problems negatively. Low scorers on self-regulation and self-direction, as well as on satisfaction with work-related achievements, were more likely to have work-attendance problems compared to high scorers. However, low scorers on interpersonal communication and work-stress problems were less likely to have work-attendance problems compared to high-scoring peers. Conclusion Ample evidence from this study showed that sociodemographic variables and social values contribute to work-attendance problems in various ways, and need to be incorporated in counseling interventions for affected employees. PMID:28919763

Numerically modeling Brownian thermal noise in amorphous and crystalline thin coatings

NASA Astrophysics Data System (ADS)

Lovelace, Geoffrey; Demos, Nicholas; Khan, Haroon

2018-01-01

Thermal noise is expected to be one of the noise sources limiting the astrophysical reach of Advanced LIGO (once commissioning is complete) and third-generation detectors. Adopting crystalline materials for thin, reflecting mirror coatings, rather than the amorphous coatings used in current-generation detectors, could potentially reduce thermal noise. Understanding and reducing thermal noise requires accurate theoretical models, but modeling thermal noise analytically is especially challenging with crystalline materials. Thermal noise models typically rely on the fluctuation-dissipation theorem, which relates the power spectral density of the thermal noise to an auxiliary elastic problem. In this paper, we present results from a new, open-source tool that numerically solves the auxiliary elastic problem to compute the Brownian thermal noise for both amorphous and crystalline coatings. We employ the open-source deal.ii and PETSc frameworks to solve the auxiliary elastic problem using a finite-element method, adaptive mesh refinement, and parallel processing that enables us to use high resolutions capable of resolving the thin reflective coating. We verify numerical convergence, and by running on up to hundreds of compute cores, we resolve the coating elastic energy in the auxiliary problem to approximately 0.1%. We compare with approximate analytic solutions for amorphous materials, and we verify that our solutions scale as expected with changing beam size, mirror dimensions, and coating thickness. Finally, we model the crystalline coating thermal noise in an experiment reported by Cole et al (2013 Nat. Photon. 7 644–50), comparing our results to a simpler numerical calculation that treats the coating as an ‘effectively amorphous’ material. We find that treating the coating as a cubic crystal instead of as an effectively amorphous material increases the thermal noise by about 3%. Our results are a step toward better understanding and reducing thermal noise to increase the reach of future gravitational-wave detectors.

IFLA General Conference, 1986. Pre-Conference Seminar on Automated Systems for Access to Multilingual and Multiscript Library materials: Problems and Solutions. Papers.

ERIC Educational Resources Information Center

International Federation of Library Associations and Institutions, The Hague (Netherlands).

A seminar which considered problems and solutions regarding automated systems for access to multilingual and multiscript library materials was held as a pre-session before the IFLA general conference in 1986. Papers presented include: (1) "Romanized and Transliterated Databases of Asian Language Materials--History, Problems, and…

A constitutive law for finite element contact problems with unclassical friction

NASA Technical Reports Server (NTRS)

Plesha, M. E.; Steinetz, B. M.

1986-01-01

Techniques for modeling complex, unclassical contact-friction problems arising in solid and structural mechanics are discussed. A constitutive modeling concept is employed whereby analytic relations between increments of contact surface stress (i.e., traction) and contact surface deformation (i.e., relative displacement) are developed. Because of the incremental form of these relations, they are valid for arbitrary load-deformation histories. The motivation for the development of such a constitutive law is that more realistic friction idealizations can be implemented in finite element analysis software in a consistent, straightforward manner. Of particular interest is modeling of two-body (i.e., unlubricated) metal-metal, ceramic-ceramic, and metal-ceramic contact. Interfaces involving ceramics are of engineering importance and are being considered for advanced turbine engines in which higher temperature materials offer potential for higher engine fuel efficiency.

[Establishment of traceability system of Chinese medicinal materials' quality].

PubMed

Qi, Yao-dong; Gao, Shi-man; Liu, Hai-tao; Li, Xi-wen; Wei, Jian-he; Zhang, Ben-gang; Sun, Xiao-bo; Xiao, Pei-gen

2015-12-01

The quality of Chinese medicinal materials relates greatly to the clinical curative effect and security. In order to ensure the quality and safety of Chinese medicinal materials, a systematic and operable traceability system needs to be established. It can realize the whole process of quality and safety management of Chinese medicinal materials "from production to consumption" through recording and inquiring information and recalling defective products, which is an important direction for the future development of traditional Chinese medicine. But it is still at the exploration and trial stage. In this paper, a framework of Chinese medicinal materials' quality and safety traceability system was established on the basis of the domestic and international experience about the construction of food and agricultural products traceability systems. The relationship between traceability system of Chinese medicinal materials' quality and GAP, GMP, GSP was analyzed, and the possible problems and the corresponding solutions were discussed.

Mishaps with Oxygen in NASA Operations

NASA Technical Reports Server (NTRS)

Ordin, Paul M.

1971-01-01

Data from a substantial number of oxygen mishaps obtained from NASA and contractor records are presented. Information from several Air Force records, concerning oxygen accidents involving aircraft operations, are also included. Descriptions of the mishaps and their causes, for both liquid and gaseous oxygen in ground test facilities and space vehicle systems, are given. A number of safety regulations aimed at reducing the accident probability is discussed. The problems related to material compatibility and materials testing are considered, and the limited information on factors affecting the ignition of materials in oxygen is presented. In addition, details are given of several of the accident/incidents listed in order to define the combination of conditions causing the mishap. In addition to propellant system mishaps, accident/incidents which occurred in space and ground system structures were included, as well as those in electrical systems, ground support facilities, ordnance, and related operations.

Directed electromagnetic wave propagation in 1D metamaterial: Projecting operators method

NASA Astrophysics Data System (ADS)

Ampilogov, Dmitrii; Leble, Sergey

2016-07-01

We consider a boundary problem for 1D electrodynamics modeling of a pulse propagation in a metamaterial medium. We build and apply projecting operators to a Maxwell system in time domain that allows to split the linear propagation problem to directed waves for a material relations with general dispersion. Matrix elements of the projectors act as convolution integral operators. For a weak nonlinearity we generalize the linear results still for arbitrary dispersion and derive the system of interacting right/left waves with combined (hybrid) amplitudes. The result is specified for the popular metamaterial model with Drude formula for both permittivity and permeability coefficients. We also discuss and investigate stationary solutions of the system related to some boundary regimes.

Thermotropic Liquid Crystal-Assisted Chemical and Biological Sensors

PubMed Central

Honaker, Lawrence W.; Usol’tseva, Nadezhda; Mann, Elizabeth K.

2017-01-01

In this review article, we analyze recent progress in the application of liquid crystal-assisted advanced functional materials for sensing biological and chemical analytes. Multiple research groups demonstrate substantial interest in liquid crystal (LC) sensing platforms, generating an increasing number of scientific articles. We review trends in implementing LC sensing techniques and identify common problems related to the stability and reliability of the sensing materials as well as to experimental set-ups. Finally, we suggest possible means of bridging scientific findings to viable and attractive LC sensor platforms. PMID:29295530

Heat storage in alloy transformations

NASA Technical Reports Server (NTRS)

Birchenall, C. E.; Gueceri, S. I.

1980-01-01

The theory of eutectic transformation was examined to find guidelines to the best material combinations to examine. The heats of transformation were measured calorimetrically, and the volume changes of expanding solid mixtures and homogeneous liquid solutions, especially during the transformation between the two states at fixed temperature, were measured by changes in X-ray absorption. Heat flow models appropriate to storage in phase change materials were developed along with efficient calculating procedures so that the relative importance of the problems associated with energy storage density, heat conduction, and similar properties could be assessed.

Social construction and materiality: the limits of indeterminacy in therapeutic settings.

PubMed

Lannamann, J W

1998-01-01

By drawing parallels between the courtroom testimony of a Christian Science practitioner and an intersession conversation between systemic family therapists, I critique the abstract idealism of language-centered social constructionism. I argue that social constructionist inquiry that highlights the indeterminacy of meaning without a corresponding emphasis on the responsive embodied practices of family members glosses over the material conditions shaping the politics of interaction. The implications of this problem are discussed as they relate to the setting of family therapy, where social construction theory is often used to guide practical interventions.

Physics teaching in developing countries

NASA Astrophysics Data System (ADS)

Talisayon, V. M.

1984-05-01

The need for endogeneous learning materials that will relate physics to the student's culture and environment spurred countries like India, Thailand, The Philippines and Indonesia to develop their own physics curriculum materials and laboratory equipment. Meagre resources and widespread poverty necessitated the development of laboratory materials from everyday items, recycled materials and other low-cost or no-cost local materials. The process of developing learning materials for one's teaching-learning needs in physics and the search from within for solutions to one's problems contribute in no small measure to the development of self-reliance in physics teaching of a developing country. Major concerns of developing countries are food supply, livelihood, health, nutrition and growth of economy. At the level of the student and his family, food, health, and livelihood are also primary concerns. Many physics teaching problems can be overcome on a large scale, given political support and national will. In countries where national leadership recognises that science and technology developed is essential to national development and that science education in turn is crucial to science and technology development, scarce resources can be allocated to science education. In developing countries where science education receives little or no political support, the most important resource in the physics classroom is the physics teacher. A highly motivated and adequately trained teacher can rise above the constraining circumstances of paucity of material resources and government apathy. In developing countries the need is great for self-reliance in physics teaching at the country level, and more importantly at the teacher level.

The recycling dilemma for advanced materials use: Automobile materials substitution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Field, F.R. III; Clark, J.P.

1991-01-01

This paper discusses the difficulties associated with imposing recycling imperatives upon advanced materials development by examining the case of automotive materials substitution and its impacts upon the recyclability of the automobile. Parallels are drawn between today's issues, which focus upon the recyclability of the increasing polymeric fraction in automobile shredder fluff, and the junked automobile problem of the 1960's, when the problem of abandoned automobiles became a part of the environmental and legislative agenda in the US and overseas. In the 1960's, both the source and the resolution of the junk automobile problem arose through a confluence of technological andmore » economic factors, rather than through any set of regulatory influences. The rise of electric arc furnace steelmaking and the development of the automobile shredder were sufficient to virtually eliminate the problem - so much so that today's problems are incorrectly viewed as novelties. Today's automobile recycling problem again derives from technological and economic factors, but regulatory influences have spurred some of them. While there are no lack of technological solutions to the problem of automobile shredder fluff, none of these solutions yet provides scrap processors with the kind of profit opportunity necessary to implement them. In some ways, it is implicit in advanced materials markets that there is little to no demand for recycled forms of these materials, and, in the absence of these markets, there are few reasons to expect that the solution to today's problems will be quite so neat.« less

LLNL small-scale static spark machine: static spark sensitivity test

DOE Office of Scientific and Technical Information (OSTI.GOV)

Foltz, M F; Simpson, L R

1999-08-23

Small-scale safety testing of explosives and other energetic materials is done in order to determine their sensitivity to various stimuli, such as friction, static spark, and impact. Typically this testing is done to discover potential handling problems that may exist for either newly synthesized materials of unknown behavior, or materials that have been stored for long periods of time. This report describes the existing ''Static Spark Test Apparatus'' at Lawrence Livermore National Laboratory (LLNL), as well as the method used to evaluate the relative static spark sensitivity of energetic materials. The basic design, originally developed by the Picatinny Arsenal inmore » New Jersey, is discussed. The accumulated data for the materials tested to date is not included here, with the exception of specific examples that have yielded interesting or unusual results during the tests.« less

DYNSYL: a general-purpose dynamic simulator for chemical processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patterson, G.K.; Rozsa, R.B.

1978-09-05

Lawrence Livermore Laboratory is conducting a safeguards program for the Nuclear Regulatory Commission. The goal of the Material Control Project of this program is to evaluate material control and accounting (MCA) methods in plants that handle special nuclear material (SNM). To this end we designed and implemented the dynamic chemical plant simulation program DYNSYL. This program can be used to generate process data or to provide estimates of process performance; it simulates both steady-state and dynamic behavior. The MCA methods that may have to be evaluated range from sophisticated on-line material trackers such as Kalman filter estimators, to relatively simplemore » material balance procedures. This report describes the overall structure of DYNSYL and includes some example problems. The code is still in the experimental stage and revision is continuing.« less

Prevalence of episiotomy in primiparas, related conditions, and effects of episiotomy on suture materials used, perineal pain, wound healing 3 weeks postpartum, in Turkey: A prospective follow-up study

PubMed Central

Karaçam, Zekiye; Ekmen, Hatice; Çalişır, Hüsniye; Şeker, Sibel

2013-01-01

Background: Despite current recommendations against routine use of episiotomy, its incidence is still high in Turkey. The study aimed to identify the prevalence of episiotomy in primiparas, related conditions, and effects of episiotomy on suture materials used, perineal pain, and wound healing 3 weeks postpartum. Materials and Methods: This study was designed as a prospective follow-up study. Data were collected via a questionnaire form between March 2007 and February 2009 in Aydın Government Hospital, Turkey. Three hundred ninety-six primiparas were included in the study by convenience sampling. Results: It was determined that 56.3% of the women had episiotomies. The results of the study revealed that the probability of receiving an episiotomy was decreased in women with lack of legal marriage and unplanned pregnancies, and increased in women who had ineffective pushing efforts approximately four times, miscellaneous two times and baby's head circumference 1.27 times. Moreover, the results of the study demonstrated that an episiotomy increased the number of the suture materials used by approximately five-fold, as well as the prevalence of pain on the first postpartum day. On the third postpartum week evaluation, it was determined that the probability of problems with wound healing and experiencing pain was approximately two times higher among women who received episiotomies than those who did not receive episiotomies. Conclusion: The study revealed that episiotomies in primiparas increased the number of suture materials used and the probability of having perineal pain on the first postpartum day, as well as perineal pain and wound-healing problems during the third postpartum week. PMID:23983762

Experimental analysis of compaction of concrete and mortar

NASA Astrophysics Data System (ADS)

Burlion, Nicolas; Pijaudier-Cabot, Gilles; Dahan, Noël

2001-12-01

Compaction of concrete is physically a collapse of the material porous microstructure. It produces plastic strains in the material and, at the same time, an increase of its bulk modulus. This paper presents two experimental techniques aimed at obtaining the hydrostatic response of concrete and mortar. The first one is a uniaxial confined compression test which is quite simple to implement and allows to reach hydrostatic pressures of about 600 MPa. The specimen size is large enough so that concrete with aggregate sizes up to 16 mm can be tested. The second one is a true hydrostatic test performed on smaller (mortar) specimens. Test results show that the hydrostatic response of the material is elasto-plastic with a stiffening effect on both the tangent and unloading bulk moduli. The magnitude of the irreversible volumetric strains depends on the initial porosity of the material. This porosity can be related in a first approximation to the water/cement ratio. A comparison of the hydrostatic responses obtained from the two testing techniques on the same material show that the hydrostatic response of cementitious materials cannot be uncoupled from the deviatoric response, as opposed to the standard assumption in constitutive relations for metal alloys. This feature should be taken into account in the development of constitutive relations for concrete subjected to high confinement pressures which are needed in the modelling of impact problems.

Computational materials design of crystalline solids.

PubMed

Butler, Keith T; Frost, Jarvist M; Skelton, Jonathan M; Svane, Katrine L; Walsh, Aron

2016-11-07

The modelling of materials properties and processes from first principles is becoming sufficiently accurate as to facilitate the design and testing of new systems in silico. Computational materials science is both valuable and increasingly necessary for developing novel functional materials and composites that meet the requirements of next-generation technology. A range of simulation techniques are being developed and applied to problems related to materials for energy generation, storage and conversion including solar cells, nuclear reactors, batteries, fuel cells, and catalytic systems. Such techniques may combine crystal-structure prediction (global optimisation), data mining (materials informatics) and high-throughput screening with elements of machine learning. We explore the development process associated with computational materials design, from setting the requirements and descriptors to the development and testing of new materials. As a case study, we critically review progress in the fields of thermoelectrics and photovoltaics, including the simulation of lattice thermal conductivity and the search for Pb-free hybrid halide perovskites. Finally, a number of universal chemical-design principles are advanced.

Problems Involved in the Choice and Use of Materials in Airplane Construction

NASA Technical Reports Server (NTRS)

Brenner, Paul

1932-01-01

The present state of the problem of materials in airplane construction is studied on the basis of data giving the principal characteristics of different materials and showing how they affect the form of airplane parts.

The Preparation and Characterization of Materials.

ERIC Educational Resources Information Center

Wold, Aaron

1980-01-01

Presents several examples illustrating different aspects of materials problems, including problems associated with solid-solid reactions, sintering and crystal growth, characterization of materials, preparation and characterization of stoichiometric ferrites and chromites, copper-sulfur systems, growth of single crystals by chemical vapor…

An interview study of persons who attribute health problems to dental filling materials--part two in a triangulation study on 65 and 75 years old Swedes.

PubMed

Ståhlnacke, Katri; Söderfeldt, Björn

2013-01-01

Dental materials are perceived as a health problem by some people, although scientists do not agree about possible causes of such problems. The aim of this paper was to gain a deeper knowledge and understanding of experiences from living with health problems attributed to dental materials. Addressed topics were the type of problem, both as to general and oral health, perceived causes of the problems,their experienced effect on life, and reception by health professionals. Persons, who in a previous large questionnaire study had answered that they had experienced troubles from dental materials and also agreed to answer follow-up questions, were contacted with a request to take part in an interview study. Eleven individual interviews were held.The interviews were transcribed verbatim and the material was analysed according to the Qualitative Content Analysis method. Meaning units were extracted and condensed into a number of codes, which were combined into subcategories, categories, and themes. Four themes were identified: 1) Long-term oral, mental, and somatic difficulties of varying character, caused by dental amalgam. 2) Problems treated mainly by replacement of dental material in fillings. 3) Powerful effects on life, mostly negative. 4) The reception by health professionals was generally good, but with elements of encounters where they felt treated with nonchalance and lack of respect. In conclusion, people who attributed their health difficulties to dental materials had a complex range of problems and the perception was that amalgam/mercury was the cause of the troubles. The reception from health professionals was perceived as generally good, although with occasional negative experiences.

Issues Related to Cleaning Complex Geometry Surfaces with ODC-Free Solvents

NASA Technical Reports Server (NTRS)

Bradford, Blake F.; Wurth, Laura A.; Nayate, Pramod D.; McCool, Alex (Technical Monitor)

2001-01-01

Implementing ozone depleting chemicals (ODC)-free solvents into full-scale reusable solid rocket motor cleaning operations has presented problems due to the low vapor pressures of the solvents. Because of slow evaporation, solvent retention is a problem on porous substrates or on surfaces with irregular geometry, such as threaded boltholes, leak check ports, and nozzle backfill joints. The new solvents are being evaluated to replace 1,1,1-trichloroethane, which readily evaporates from these surfaces. Selection of the solvents to be evaluated on full-scale hardware was made based on results of subscale tests performed with flat surface coupons, which did not manifest the problem. Test efforts have been undertaken to address concerns with the slow-evaporating solvents. These concerns include effects on materials due to long-term exposure to solvent, potential migration from bolthole threads to seal surfaces, and effects on bolt loading due to solvent retention in threads. Tests performed to date have verified that retained solvent does not affect materials or hardware performance. Process modifications have also been developed to assist drying, and these can be implemented if additional drying becomes necessary.

Contingencies and metacontingencies: Toward a synthesis of behavior analysis and cultural materialism

PubMed Central

Glenn, Sigrid S.

1988-01-01

A synthesis of cultural materialism and behavior analysis might increase the scientific and technological value of both fields. Conceptual and substantive relations between the two fields show important similarities, particularly with regard to the causal role of the environment in behavioral and cultural evolution. Key concepts in Marvin Harris's cultural materialist theories are outlined. A distinction is made between contingencies at the behavioral level of analysis (contingencies of reinforcement) and contingencies at the cultural level of analysis (metacontingencies). Relations between the two kinds of contingencies are explored in cultural practices from paleolithic to industrial sociocultural systems. A synthesis of these two fields may offer the opportunity to resolve serious problems currently facing modern cultures. PMID:22478011

Recent global trends in structural materials research

NASA Astrophysics Data System (ADS)

Murakami, Hideyuki; Ohmura, Takahito; Nishimura, Toshiyuki

2013-02-01

Structural materials support the basis of global society, such as infrastructure and transportation facilities, and are therefore essential for everyday life. The optimization of such materials allows people to overcome environmental, energy and resource depletion issues on a global scale. The creation and manufacture of structural materials make a large contribution to economies around the world every year. The use of strong, resistant materials can also have profound social effects, providing a better quality of life at both local and national levels. The Great East Japan Earthquake of 11 March 2011 caused significant structural damage in the Tohoku and Kanto regions of Japan. On a global scale, accidents caused by the ageing and failure of structural materials occur on a daily basis. Therefore, the provision and inspection of structural reliability, safety of nuclear power facilities and construction of a secure and safe society hold primary importance for researchers and engineers across the world. Clearly, structural materials need to evolve further to address both existing problems and prepare for new challenges that may be faced in the future. With this in mind, the National Institute for Materials Science (NIMS) organized the 'NIMS Conference 2012' to host an extensive discussion on a variety of global issues related to the future development of structural materials. Ranging from reconstruction following natural disasters, verification of structural reliability, energy-saving materials to fundamental problems accompanying the development of materials for high safety standards, the conference covered many key issues in the materials industry today. All the above topics are reflected in this focus issue of STAM, which introduces recent global trends in structural materials research with contributions from world-leading researchers in this field. This issue covers the development of novel alloys, current methodologies in the characterization of structural materials and fundamental research on structure-property relationships. We are grateful to the authors who contributed to cover these issues, and sincerely hope that our readers will expand their knowledge of emerging international research within the field of structural materials.

Teen Drinking Prevention Program. Communicator's Guide.

ERIC Educational Resources Information Center

Substance Abuse and Mental Health Services Administration (DHHS/PHS), Rockville, MD. Center for Substance Abuse Prevention.

Underage drinking is a serious national problem--alcohol-related injuries are a leading cause of death and injury among young people in the United States today. This guide is designed to help individuals who wish to be involved in a national effort to prevent underage drinking. It includes materials and messages that can be reproduced, as well as…

Open-Ended Cases in Agroecology: Farming and Food Systems in the Nordic Region and the US Midwest

ERIC Educational Resources Information Center

Francis, Charles; King, James; Lieblein, Geir; Breland, Tor Arvid; Salomonsson, Lennart; Sriskandarajah, Nadarajah; Porter, Paul; Wiedenhoeft, Mary

2009-01-01

Our aim is to describe open-ended case studies for learning real-life problem solving skills, and relate this approach to conventional, closed-ended decision case studies. Teaching methods are open-ended cases in agroecology, an alternative to traditional strategies that lead students through prepared materials and structured discussions to…

[Paradigm shift in health: forecasting and causation as a basis for risk management].

PubMed

Denisov, E I; Prokopenko, L V; Golovaneva, G V; Stepanian, I V

2012-01-01

The problem of occupational risk management (ORM) is discussed using the evidence-based medicine approach and bio- and IT-technologies. The prognosis and causation of work-related health disorders are analyzed as components of ORM system. The Web-based handbook "Occupational risk assessment" with software and information materials as practical tool is presented.

Scientific ballooning. Proceedings. PSB Meeting of the COSPAR Panel on Technical Problems Related to Scientific Ballooning which was held during the Thirtieth COSPAR Scientific Assembly, Hamburg (Germany), 11 - 21 Jul 1994.

NASA Astrophysics Data System (ADS)

Riedler, W.; Torkar, K.

1996-05-01

This issue is grouped into sections on materials, design, performance and analysis of balloons, reviews of major national and international balloon programmes, novel instrumentation and systems for scientific ballooning, and selected recent scientific observations.

Quality of Living: Environmental Viewpoints. Make Up Your Own Mind, Book 3.

ERIC Educational Resources Information Center

Pollis, Adamantia, Ed.

This book is the third in a series of discussion materials, this issue being part of an action project to increase environmental awareness. Over 60 readings are included that cover a wide variety of opinions and interpretations of specific environmental problems and related philosophic issues. Examples of topics discussed include population, land…

The Invasion of the Giant Spore. SOLINET Preservation Program Leaflet Number 5.

ERIC Educational Resources Information Center

Nyberg, Sandra

This report addresses solutions to problems of fungus growth on library materials. The first of four sections--"What Is Mold? Where Does It Come From?"--defines mold, mildew, and fungi, and describes their optimum environment (i.e., generally in conditions with temperatures above 70 degrees and relative humidity above 78%). The second…

Acoustics in Research Facilities--Control of Wanted and Unwanted Sound. Laboratory Design Notes.

ERIC Educational Resources Information Center

Newman, Robert B.

Common and special acoustics problems are discussed in relation to the design and construction of research facilities. Following a brief examination of design criteria for the control of wanted and unwanted sound, the technology for achieving desired results is discussed. Emphasis is given to various design procedures and materials for the control…

Biomass I. Science Activities in Energy [and] Teacher's Guide.

ERIC Educational Resources Information Center

Oak Ridge Associated Universities, TN.

Designed for science students in fourth, fifth, and sixth grades, the activities in this unit illustrate principles and problems related to biomass as a form of energy. (The word biomass is used to describe all solid material of animal or vegetable origin from which energy may be extracted.) Twelve student activities using art, economics,…

International High/Scope Registry Conference Proceedings (Ypsilanti, Michigan, May 8-11, 1996).

ERIC Educational Resources Information Center

High/Scope Educational Research Foundation, Ypsilanti, MI.

These conference proceedings provide summaries of 66 presentations on various aspects of the High/Scope active learning approach for high-risk students, as well as related topics. Topics addressed include: (1) real-life problem solving; (2) songs in daily routines; (3) open-ended art materials; (4) transition strategies; (5) recall ideas for…

The Innovative Activity of Schools in a Regional System of Education

ERIC Educational Resources Information Center

Larina, V. P.

2006-01-01

Education today is characterized by two opposite tendencies: (1) A centripetal tendency, which conditions the link between the region and the center, without which it is not possible to find local solutions to a number of important problems related to resource support for the regional system of education (legal, normative, material and technical,…

[Chicano Bibliography. Education...the Last Hope of the Poor Chicano (Educacion...La Ultima Esperanza Del Pobre Chicano).

ERIC Educational Resources Information Center

Garza, Ben; And Others

Developed to support Chicano studies and provide Chicano students with readings which would explore the Chicano heritage, this bibliography lists approximately 900 sources pertaining to Mexican history and prehistory. Included are materials relating to Chicano problems such as health and nutrition, employment and working conditions, education and…

A Curriculum Activities Guide to Solid Wastes and Environmental Studies, Volume 4.

ERIC Educational Resources Information Center

Hershey, John T., Ed.; And Others

This document, developed for elementary and secondary students, is one of a series emphasizing student-oriented problem solving related to environmental matters. It is designed to guide others in initiating, continuing, or expanding their environmental education program. Volume 4 is intended for use by cadre who have used similar materials at a…

An n -material thresholding method for improving integerness of solutions in topology optimization

DOE PAGES

Watts, Seth; Tortorelli, Daniel A.

2016-04-10

It is common in solving topology optimization problems to replace an integer-valued characteristic function design field with the material volume fraction field, a real-valued approximation of the design field that permits "fictitious" mixtures of materials during intermediate iterations in the optimization process. This is reasonable so long as one can interpolate properties for such materials and so long as the final design is integer valued. For this purpose, we present a method for smoothly thresholding the volume fractions of an arbitrary number of material phases which specify the design. This method is trivial for two-material design problems, for example, themore » canonical topology design problem of specifying the presence or absence of a single material within a domain, but it becomes more complex when three or more materials are used, as often occurs in material design problems. We take advantage of the similarity in properties between the volume fractions and the barycentric coordinates on a simplex to derive a thresholding, method which is applicable to an arbitrary number of materials. As we show in a sensitivity analysis, this method has smooth derivatives, allowing it to be used in gradient-based optimization algorithms. Finally, we present results, which show synergistic effects when used with Solid Isotropic Material with Penalty and Rational Approximation of Material Properties material interpolation functions, popular methods of ensuring integerness of solutions.« less

The effects of gamma irradiation on diclofenac sodium, liposome and niosome ingredients for rheumatoid arthritis

PubMed Central

Turker, Selcan; Çolak, Seyda; Korkmaz, Mustafa; Kiliç, Ekrem; Özalp, Meral

2013-01-01

The use of gamma rays for the sterilization of pharmaceutical raw materials and dosage forms is an alternative method for sterilization. However, one of the major problems of the radiosterilization is the production of new radiolytic products during the irradiation process. Therefore, the principal problem in radiosterilization is to determine and to characterize these physical and chemical changes originating from high-energy radiation. Parenteral drug delivery systems were prepared and in vitro characterization, biodistribution and treatment studies were done in our previous studies. Drug delivery systems (liposomes, niosomes, lipogelosomes and niogelosomes) encapsulating diclofenac sodium (DFNa) were prepared for the treatment of rheumatoid arthritis (RA). This work complies information about the studies developed in order to find out if gamma radiation could be applied as a sterilization method to DFNa, and the raw materials as dimyristoyl phosphatidylcholine (DMPC), surfactant I [polyglyceryl-3-cethyl ether (SUR I)], dicethyl phosphate (DCP) and cholesterol (CHOL) that are used to prepare those systems. The raw materials were irradiated with different radiation doses (5, 10, 25 and 50 kGy) and physicochemical changes (organoleptic properties pH, UV and melting point), microbiological evaluation [sterility assurance level (SAL), sterility and pyrogen test] and electron spin resonance (ESR) characteristics were studied at normal (25 °C, 60% relative humidity) and accelerated (40 °C, 75% relative humidity) stability test conditions. PMID:24265902

Strategies to curb structural changes of lithium/transition metal oxide cathode materials & the changes' effects on thermal & cycling stability

DOE PAGES

Yu, Xiqian; Hu, Enyuan; Bak, Seongmin; ...

2015-12-07

Structural transformation behaviors of several typical oxide cathode materials during a heating process are reviewed in detail to provide in-depth understanding of the key factors governing the thermal stability of these materials. Furthermore, we also discuss applying the information about heat induced structural evolution in the study of electrochemically induced structural changes. All these discussions are expected to provide valuable insights for designing oxide cathode materials with significantly improved structural stability for safe, long-life lithium ion batteries, as the safety of lithium-ion batteries is a critical issue. As a result, it is widely accepted that the thermal instability of themore » cathodes is one of the most critical factors in thermal runaway and related safety problems.« less

Study on validation method for femur finite element model under multiple loading conditions

NASA Astrophysics Data System (ADS)

Guan, Fengjiao; Zhang, Guanjun; Liu, Jie; Wang, Shujing; Luo, Xu

2018-03-01

Acquisition of accurate and reliable constitutive parameters related to bio-tissue materials was beneficial to improve biological fidelity of a Finite Element (FE) model and predict impact damages more effectively. In this paper, a femur FE model was established under multiple loading conditions with diverse impact positions. Then, based on sequential response surface method and genetic algorithms, the material parameters identification was transformed to a multi-response optimization problem. Finally, the simulation results successfully coincided with force-displacement curves obtained by numerous experiments. Thus, computational accuracy and efficiency of the entire inverse calculation process were enhanced. This method was able to effectively reduce the computation time in the inverse process of material parameters. Meanwhile, the material parameters obtained by the proposed method achieved higher accuracy.

A Novel Microcharacterization Technique in the Measurement of Strain and Orientation Gradient in Advanced Materials

NASA Technical Reports Server (NTRS)

Garmestai, H.; Harris, K.; Lourenco, L.

1997-01-01

Representation of morphology and evolution of the microstructure during processing and their relation to properties requires proper experimental techniques. Residual strains, lattice distortion, and texture (micro-texture) at the interface and the matrix of a layered structure or a functionally gradient material and their variation are among parameters important in materials characterization but hard to measure with present experimental techniques. Current techniques available to measure changes in interred material parameters (residual stress, micro-texture, microplasticity) produce results which are either qualitative or unreliable. This problem becomes even more complicated in the case of a temperature variation. These parameters affect many of the mechanical properties of advanced materials including stress-strain relation, ductility, creep, and fatigue. A review of some novel experimental techniques using recent advances in electron microscopy is presented here to measure internal stress, (micro)texture, interracial strength and (sub)grain formation and realignment. Two of these techniques are combined in the chamber of an Environmental Scanning Electron Microscope to measure strain and orientation gradients in advanced materials. These techniques which include Backscattered Kikuchi Diffractometry (BKD) and Microscopic Strain Field Analysis are used to characterize metallic and intermetallic matrix composites and superplastic materials. These techniques are compared with the more conventional x-ray diffraction and indentation techniques.

Ideal flow theory for the double - shearing model as a basis for metal forming design

NASA Astrophysics Data System (ADS)

Alexandrov, S.; Trung, N. T.

2018-02-01

In the case of Tresca’ solids (i.e. solids obeying the Tresca yield criterion and its associated flow rule) ideal flows have been defined elsewhere as solenoidal smooth deformations in which an eigenvector field associated everywhere with the greatest principal stress (and strain rate) is fixed in the material. Under such conditions all material elements undergo paths of minimum plastic work, a condition which is often advantageous for metal forming processes. Therefore, the ideal flow theory is used as the basis of a procedure for the preliminary design of such processes. The present paper extends the theory of stationary planar ideal flow to pressure dependent materials obeying the double shearing model and the double slip and rotation model. It is shown that the original problem of plasticity reduces to a purely geometric problem. The corresponding system of equations is hyperbolic. The characteristic relations are integrated in elementary functions. In regions where one family of characteristics is straight, mapping between the principal lines and Cartesian coordinates is determined by linear ordinary differential equations. An illustrative example is provided.

Comprehensive Enhancement of Nanostructured Lithium-Ion Battery Cathode Materials via Conformal Graphene Dispersion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Kan-Sheng; Xu, Rui; Luu, Norman S.

Efficient energy storage systems based on lithium-ion batteries represent a critical technology across many sectors including consumer electronics, electrified transportation, and a smart grid accommodating intermittent renewable energy sources. Nanostructured electrode materials present compelling opportunities for high-performance lithium-ion batteries, but inherent problems related to the high surface area to volume ratios at the nanometer-scale have impeded their adoption for commercial applications. Here, we demonstrate a materials and processing platform that realizes high-performance nanostructured lithium manganese oxide (nano-LMO) spinel cathodes with conformal graphene coatings as a conductive additive. The resulting nanostructured composite cathodes concurrently resolve multiple problems that have plagued nanoparticle-basedmore » lithium-ion battery electrodes including low packing density, high additive content, and poor cycling stability. Moreover, this strategy enhances the intrinsic advantages of nano-LMO, resulting in extraordinary rate capability and low temperature performance. With 75% capacity retention at a 20C cycling rate at room temperature and nearly full capacity retention at -20 degrees C, this work advances lithium-ion battery technology into unprecedented regimes of operation.« less

The prediction of crystal structure by merging knowledge methods with first principles quantum mechanics

NASA Astrophysics Data System (ADS)

Ceder, Gerbrand

2007-03-01

The prediction of structure is a key problem in computational materials science that forms the platform on which rational materials design can be performed. Finding structure by traditional optimization methods on quantum mechanical energy models is not possible due to the complexity and high dimensionality of the coordinate space. An unusual, but efficient solution to this problem can be obtained by merging ideas from heuristic and ab initio methods: In the same way that scientist build empirical rules by observation of experimental trends, we have developed machine learning approaches that extract knowledge from a large set of experimental information and a database of over 15,000 first principles computations, and used these to rapidly direct accurate quantum mechanical techniques to the lowest energy crystal structure of a material. Knowledge is captured in a Bayesian probability network that relates the probability to find a particular crystal structure at a given composition to structure and energy information at other compositions. We show that this approach is highly efficient in finding the ground states of binary metallic alloys and can be easily generalized to more complex systems.

Analyses of phase change materials’ efficiency in warm-summer humid continental climate conditions

NASA Astrophysics Data System (ADS)

Ratnieks, J.; Gendelis, S.; Jakovics, A.; Bajare, D.

2017-10-01

The usage of phase change materials (PCMs) is a way to store excess energy produced during the hot time of the day and release it during the night thereby reducing the overheating problem. While, in Latvian climate conditions overheating is not a big issue in traditional buildings since it happens only a couple of weeks per year air conditioners must still be installed to maintain thermal comfort. The need for cooling in recently built office buildings with large window area can increase significantly. It is therefore of great interest if the thermal comfort conditions can be maintained by PCMs alone or with reduced maximum power of installed cooling systems. Our initial studies show that if the test building is well-insulated (necessary to reduce heat loss in winter), phase change material is not able to solidify fast enough during the relatively short night time. To further investigate the problem various experimental setups with two different phase change materials were installed in test buildings. Experimental results are compared with numerical modelling made in software COMSOL Multiphysics. The effectiveness of PCM using different situations is widely analysed.

Comprehensive Enhancement of Nanostructured Lithium-Ion Battery Cathode Materials via Conformal Graphene Dispersion.

PubMed

Chen, Kan-Sheng; Xu, Rui; Luu, Norman S; Secor, Ethan B; Hamamoto, Koichi; Li, Qianqian; Kim, Soo; Sangwan, Vinod K; Balla, Itamar; Guiney, Linda M; Seo, Jung-Woo T; Yu, Xiankai; Liu, Weiwei; Wu, Jinsong; Wolverton, Chris; Dravid, Vinayak P; Barnett, Scott A; Lu, Jun; Amine, Khalil; Hersam, Mark C

2017-04-12

Efficient energy storage systems based on lithium-ion batteries represent a critical technology across many sectors including consumer electronics, electrified transportation, and a smart grid accommodating intermittent renewable energy sources. Nanostructured electrode materials present compelling opportunities for high-performance lithium-ion batteries, but inherent problems related to the high surface area to volume ratios at the nanometer-scale have impeded their adoption for commercial applications. Here, we demonstrate a materials and processing platform that realizes high-performance nanostructured lithium manganese oxide (nano-LMO) spinel cathodes with conformal graphene coatings as a conductive additive. The resulting nanostructured composite cathodes concurrently resolve multiple problems that have plagued nanoparticle-based lithium-ion battery electrodes including low packing density, high additive content, and poor cycling stability. Moreover, this strategy enhances the intrinsic advantages of nano-LMO, resulting in extraordinary rate capability and low temperature performance. With 75% capacity retention at a 20C cycling rate at room temperature and nearly full capacity retention at -20 °C, this work advances lithium-ion battery technology into unprecedented regimes of operation.

The Need for Social Ethics in Interdisciplinary Environmental Science Graduate Programs: Results from a Nation-Wide Survey in the United States.

PubMed

Hall, Troy E; Engebretson, Jesse; O'Rourke, Michael; Piso, Zach; Whyte, Kyle; Valles, Sean

2017-04-01

Professionals in environmental fields engage with complex problems that involve stakeholders with different values, different forms of knowledge, and contentious decisions. There is increasing recognition of the need to train graduate students in interdisciplinary environmental science programs (IESPs) in these issues, which we refer to as "social ethics." A literature review revealed topics and skills that should be included in such training, as well as potential challenges and barriers. From this review, we developed an online survey, which we administered to faculty from 81 United States colleges and universities offering IESPs (480 surveys were completed). Respondents overwhelmingly agreed that IESPs should address values in applying science to policy and management decisions. They also agreed that programs should engage students with issues related to norms of scientific practice. Agreement was slightly less strong that IESPs should train students in skills related to managing value conflicts among different stakeholders. The primary challenges to incorporating social ethics into the curriculum were related to the lack of materials and expertise for delivery, though challenges such as ethics being marginalized in relation to environmental science content were also prominent. Challenges related to students' interest in ethics were considered less problematic. Respondents believed that social ethics are most effectively delivered when incorporated into existing courses, and they preferred case studies or problem-based learning for delivery. Student competence is generally not assessed, and respondents recognized a need for both curricular materials and assessment tools.

Innovating e-waste management: From macroscopic to microscopic scales.

PubMed

Zeng, Xianlai; Yang, Congren; Chiang, Joseph F; Li, Jinhui

2017-01-01

Waste electrical and electronic equipment (WEEE or e-waste) has become a global problem, due to its potential environmental pollution and human health risk, and its containing valuable resources (e.g., metals, plastics). Recycling for e-waste will be a necessity, not only to address the shortage of mineral resources for electronics industry, but also to decline environmental pollution and human health risk. To systematically solve the e-waste problem, more attention of e-waste management should transfer from macroscopic to microscopic scales. E-waste processing technology should be significantly improved to diminish and even avoid toxic substance entering into downstream of material. The regulation or policy related to new production of hazardous substances in recycled materials should also be carried out on the agenda. All the findings can hopefully improve WEEE legislation for regulated countries and non-regulated countries. Copyright © 2016 Elsevier B.V. All rights reserved.

COMPARISON OF MONTE CARLO METHODS FOR NONLINEAR RADIATION TRANSPORT

DOE Office of Scientific and Technical Information (OSTI.GOV)

W. R. MARTIN; F. B. BROWN

2001-03-01

Five Monte Carlo methods for solving the nonlinear thermal radiation transport equations are compared. The methods include the well-known Implicit Monte Carlo method (IMC) developed by Fleck and Cummings, an alternative to IMC developed by Carter and Forest, an ''exact'' method recently developed by Ahrens and Larsen, and two methods recently proposed by Martin and Brown. The five Monte Carlo methods are developed and applied to the radiation transport equation in a medium assuming local thermodynamic equilibrium. Conservation of energy is derived and used to define appropriate material energy update equations for each of the methods. Details of the Montemore » Carlo implementation are presented, both for the random walk simulation and the material energy update. Simulation results for all five methods are obtained for two infinite medium test problems and a 1-D test problem, all of which have analytical solutions. Conclusions regarding the relative merits of the various schemes are presented.« less

Synthesis of Li2MnSiO4-graphene composite and its electrochemical performances as a cathode material for lithium ion batteries.

PubMed

Kim, Jeonghyun; Song, Taeseup; Park, Hyunjung; Yuh, Junhan; Paik, Ungyu

2014-10-01

The Li2MnSiO4 is a promising candidate as a cathode for lithium ion batteries due to its large theoretical capacity of 330 mA h g(-1) and high thermal stability. However, the problems related to low electronic conductivity and large irreversible capacity at the first cycle limits its practical use as a Li-ion cathode material. We have developed a carbon coated Li2MnSiO4-graphene composite electrode to overcome these problems. Our designed electrode exhibits high reversible capacity of 301 mA h g(-1), with a high initial coulombic efficiency, and a discharge capacity at current rate of 0.5 C, that is double value of carbon coated Li2MnSiO4-carbon black composite electrode. These significant improvements are attributed to fast electron transport along the graphene sheet.

Forensic engineering: applying materials and mechanics principles to the investigation of product failures.

PubMed

Hainsworth, S V; Fitzpatrick, M E

2007-06-01

Forensic engineering is the application of engineering principles or techniques to the investigation of materials, products, structures or components that fail or do not perform as intended. In particular, forensic engineering can involve providing solutions to forensic problems by the application of engineering science. A criminal aspect may be involved in the investigation but often the problems are related to negligence, breach of contract, or providing information needed in the redesign of a product to eliminate future failures. Forensic engineering may include the investigation of the physical causes of accidents or other sources of claims and litigation (for example, patent disputes). It involves the preparation of technical engineering reports, and may require giving testimony and providing advice to assist in the resolution of disputes affecting life or property.This paper reviews the principal methods available for the analysis of failed components and then gives examples of different component failure modes through selected case studies.

Crystal growth of device quality GaAs in space

NASA Technical Reports Server (NTRS)

Gatos, H. C.; Lagowski, J.

1985-01-01

The present program has been aimed at solving the fundamental and technological problems associated with Crystal Growth of Device Quality in Space. The initial stage of the program was devoted strictly to ground-based research. The unsolved problems associated with the growth of bulk GaAs in the presence of gravitational forces were explored. Reliable chemical, structural and electronic characterization methods were developed which would permit the direct relation of the salient materials parameters (particularly those affected by zero gravity conditions) to the electronic characteristics of single crystal GaAs, in turn to device performance. These relationships are essential for the development of optimum approaches and techniques. It was concluded that the findings on elemental semiconductors Ge and Si regarding crystal growth, segregation, chemical composition, defect interactions, and materials properties-electronic properties relationships are not necessarily applicable to GaAs (and to other semiconductor compounds). In many instances totally unexpected relationships were found to prevail.

Cleaning of printed circuit assemblies with surface-mounted components

NASA Astrophysics Data System (ADS)

Arzigian, J. S.

The need for ever-increasing miniaturization of airborne instrumentation through the use of surface mounted components closely placed on printed circuit boards highlights problems with traditional board cleaning methods. The reliability of assemblies which have been cleaned with vapor degreasing and spray cleaning can be seriously compromised by residual contaminants leading to solder joint failure, board corrosion, and even electrical failure of the mounted parts. In addition, recent government actions to eliminate fully halogenated chlorofluorocarbons (CFC) and chlorinated hydrocarbons from the industrial environment require the development of new cleaning materials and techniques. This paper discusses alternative cleaning materials and techniques and results that can be expected with them. Particular emphasis is placed on problems related to surface-mounted parts. These new techniques may lead to improved circuit reliability and, at the same time, be less expensive and less environmentally hazardous than the traditional systems.

Silicon solar cell process development, fabrication, and analysis

NASA Technical Reports Server (NTRS)

Yoo, H. I.; Iles, P. A.; Leung, D. C.

1981-01-01

Work has progressed in fabrication and characterization of solar cells from ubiquitous crystallization process (UCP) wafers and LASS ribbons. Gettering tests applied to UCP wafers made little change on their performance compared with corresponding baseline data. Advanced processes such as shallow junction (SJ), back surface field (BSF), and multilayer antireflection (MLAR) were also applied. While BSF by Al paste had shunting problems, cells with SJ and BSF by evaporated Al, and MLAR did achieve 14.1% AMI on UCP silicon. The study of LASS material was very preliminary. Only a few cells with SJ, BSR, (no BSF) and MLAR were completed due to mechanical yield problems after lapping the material. Average efficiency was 10.7% AMI with 13.4% AMI for CZ controls. Relatively high minority carrier diffusion lengths were obtained. The lower than expected Jsc could be partially explained by low active area due to irregular sizes.

Psychosocial dimensions of solving an indoor air problem.

PubMed

Lahtinen, Marjaana; Huuhtanen, Pekka; Kähkönen, Erkki; Reijula, Kari

2002-03-01

This investigation focuses on the psychological and social dimensions of managing and solving indoor air problems. The data were collected in nine workplaces by interviews (n = 85) and questionnaires (n = 375). Indoor air problems in office environments have traditionally utilized industrial hygiene or technical expertise. However, indoor air problems at workplaces are often more complex issues to solve. Technical questions are inter-related with the dynamics of the work community, and the cooperation and interaction skills of the parties involved in the solving process are also put to the test. In the present study, the interviewees were very critical of the process of solving the indoor air problem. The responsibility for coordinating the problem-managing process was generally considered vague, as were the roles and functions of the various parties. Communication problems occurred and rumors about the indoor air problem circulated widely. Conflicts were common, complicating the process in several ways. The research focused on examining different ways of managing and resolving an indoor air problem. In addition, reference material on the causal factors of the indoor air problem was also acquired. The study supported the hypothesis that psychosocial factors play a significant role in indoor air problems.

Effective use of real-life events as tools for teaching-learning clinical pharmacology in a problem-based learning curriculum.

PubMed

James, Henry; Al Khaja, Khalid A; Sequeira, Reginald P

2015-01-01

This paper describes how in a problem-based learning (PBL) medical curriculum, having identified the learning outcomes, problems can be developed from real-life events for teaching-learning clinical pharmacology topics for which PBL cases might be inadequate. Such problems can be very interesting and educational. Using the story of the development and withdrawal of rofecoxib (Vioxx(®)), we developed a problem for undergraduate medical students to address important issues related to clinical pharmacology and therapeutics such as new drug development, preclinical testing, clinical trials, adverse drug reactions, professionalism, and critical appraisal of literature. These topics would otherwise be difficult to address in patient-based problems. The evaluation of the problem based on pooled feedback from 57 tutorial groups, each comprising 8-10 students, collected over 5 years, supported the effectiveness of the problem. A systematic approach described in this paper can be used for the development and validation of educational material for introducing focal topics of pharmacology/clinical pharmacology integrated with other disciplines in innovative medical (and other health profession) curricula.

The benefits of computer-generated feedback for mathematics problem solving.

PubMed

Fyfe, Emily R; Rittle-Johnson, Bethany

2016-07-01

The goal of the current research was to better understand when and why feedback has positive effects on learning and to identify features of feedback that may improve its efficacy. In a randomized experiment, second-grade children received instruction on a correct problem-solving strategy and then solved a set of relevant problems. Children were assigned to receive no feedback, immediate feedback, or summative feedback from the computer. On a posttest the following day, feedback resulted in higher scores relative to no feedback for children who started with low prior knowledge. Immediate feedback was particularly effective, facilitating mastery of the material for children with both low and high prior knowledge. Results suggest that minimal computer-generated feedback can be a powerful form of guidance during problem solving. Copyright © 2016 Elsevier Inc. All rights reserved.

IRIS Toxicological Review of Polychlorinated Biphenyls (PCBS) (Scoping and Problem Formulation Materials)

EPA Science Inventory

In March 2015, EPA invited the public to provide input and participate in discussions about problem formulation, preliminary assessment materials, and draft IRIS assessments. During problem formulation, the IRIS Program was looking for input from the scientific community and the ...

Does the "new philosophy" in predictive, preventive and personalised medicine require new ethics?

PubMed

Gefenas, Eugenijus; Cekanauskaite, Asta; Tuzaite, Egle; Dranseika, Vilius; Characiejus, Dainius

2011-06-01

This paper maps the ethical issues that arise in the context of personalised medicine. First, it highlights the ethical problems related to increased predictive power of modern diagnostic interventions. Such problems emerge because the ability to identify individuals or groups of individuals that can potentially benefit from a particular therapeutic intervention also raises a question of personal responsibility for health-related behaviour and lifestyle. The second major area of ethical concern is related to health prevention and distributive justice. The paper discusses the ethical challenges brought by the personalised medicine in the context of the Additional Protocol to the Convention on Human Rights and Biomedicine concerning Genetic Testing for Health Purposes. Finally, it notes that the issue of consent in the context of biobanks, the need to rethink the prevalent models of research designs and to communicate relevant findings to the donors of biological materials deserve further discussion.

Mathematical model of the heat transfer process taking into account the consequences of nonlocality in structurally sensitive materials

NASA Astrophysics Data System (ADS)

Kuvyrkin, G. N.; Savelyeva, I. Y.; Kuvshynnikova, D. A.

2018-04-01

Creation of new materials based on nanotechnology is an important direction of modern materials science development. Materials obtained using nanotechnology can possess unique physical-mechanical and thermophysical properties, allowing their effective use in structures exposed to high-intensity thermomechanical effects. An important step in creation and use of new materials is the construction of mathematical models to describe the behavior of these materials in a wide range of changes under external effects. The model of heat conduction of structural-sensitive materials is considered with regard to the medium nonlocality effects. The relations of the mathematical model include an integral term describing the spatial nonlocality of the medium. A difference scheme, which makes it possible to obtain a numerical solution of the problem of nonstationary heat conduction with regard to the influence of the medium nonlocality on space, has been developed. The influence of the model parameters on the temperature distributions is analyzed.

Effect of a Diffusion Zone on Fatigue Crack Propagation in Layered FGMs

NASA Astrophysics Data System (ADS)

Hauber, Brett; Brockman, Robert; Paulino, Glaucio

2008-02-01

Research into functionally graded materials (FGMs) has led to advances in our ability to analyze cracks. However, two prominent aspects remain relatively unexplored: 1) development and validation of modeling methods for fatigue crack propagation in FGMs, and 2) experimental validation of stress intensity models in engineered materials such as two phase monolithic and graded materials. This work addresses some of these problems for a limited set of conditions, material systems (e.g., Ti/TiB), and material gradients. Numerical analyses are conducted for single edge notch bend (SENB) specimens. Stress intensity factors are computed using the specialized finite element code I-Franc (Illinois Fracture Analysis Code), which is tailored for both homogeneous and graded materials, as well as Franc2DL and ABAQUS. Crack extension is considered by means of specified crack increments, together with fatigue evaluations to predict crack propagation life. Results will be used to determine linear material gradient parameters that are significant for prediction of fatigue crack growth behavior.

Solution algorithms for nonlinear transient heat conduction analysis employing element-by-element iterative strategies

NASA Technical Reports Server (NTRS)

Winget, J. M.; Hughes, T. J. R.

1985-01-01

The particular problems investigated in the present study arise from nonlinear transient heat conduction. One of two types of nonlinearities considered is related to a material temperature dependence which is frequently needed to accurately model behavior over the range of temperature of engineering interest. The second nonlinearity is introduced by radiation boundary conditions. The finite element equations arising from the solution of nonlinear transient heat conduction problems are formulated. The finite element matrix equations are temporally discretized, and a nonlinear iterative solution algorithm is proposed. Algorithms for solving the linear problem are discussed, taking into account the form of the matrix equations, Gaussian elimination, cost, and iterative techniques. Attention is also given to approximate factorization, implementational aspects, and numerical results.

Apollo experience report: Lunar module environmental control subsystem

NASA Technical Reports Server (NTRS)

Gillen, R. J.; Brady, J. C.; Collier, F.

1972-01-01

A functional description of the environmental control subsystem is presented. Development, tests, checkout, and flight experiences of the subsystem are discussed; and the design fabrication, and operational difficulties associated with the various components and subassemblies are recorded. Detailed information is related concerning design changes made to, and problems encountered with, the various elements of the subsystem, such as the thermal control water sublimator, the carbon dioxide sensing and control units, and the water section. The problems associated with water sterilization, water/glycol formulation, and materials compatibility are discussed. The corrective actions taken are described with the expection that this information may be of value for future subsystems. Although the main experiences described are problem oriented, the subsystem has generally performed satisfactorily in flight.

The surface crack problem in an orthotropic plate under bending and tension

NASA Technical Reports Server (NTRS)

Wu, Bing-Hua; Erdogan, F.

1987-01-01

The elasticity problem for an infinite orthotropic flat plate containing a series of through and part through cracks and subjected to bending and tension loads is considered. The problem is formulated by using Reissner's plate bending theory and considering three-dimensional material orthotropy. The Line-spring model developed by Rice and Levy is used to formulate the surface crack problem in which a total of nine material constants were used. The effects of material orthotropy on the stress intensity factors was determined, the interaction between two asymmetrically arranged collinear cracks was investigated, and extensive numerical results regarding the stress intensity factors are provided. The problem is reduced to a system of singular integral equations which is solved by using the Gauss-Chebyshev quadrature formulas. The calculated results show that the material orthotropy does have a significant effect on the stress intensity factor.

The surface crack problem in an orthotropic plate under bending and tension

NASA Technical Reports Server (NTRS)

Wu, B. H.; Erdogan, F.

1986-01-01

The elasticity problem for an infinite orthotropic flat plate containing a series of through and part-through cracks and subjected to bending and tension loads is considered. The problem is formulated by using Reissner's plate bending theory and considering three dimensional materials orthotropy. The Line-spring model developed by Rice and Levy is used to formulate the surface crack problem in which a total of nine material constants has been used. The main purpose of this study is to determine the effect of material orthotropy on the stress intensity factors, to investigate the interaction between two asymmetrically arranged collinear cracks, and to provide extensive numerical results regarding the stress intensity factors. The problem is reduced to a system of singular integral equations which is solved by using the Gauss-Chebyshev quadrature formulas. The calculated results show that the material orthotropy does have a significant effect on the stress intensity factor.

Bi-Objective Modelling for Hazardous Materials Road–Rail Multimodal Routing Problem with Railway Schedule-Based Space–Time Constraints

PubMed Central

Sun, Yan; Lang, Maoxiang; Wang, Danzhu

2016-01-01

The transportation of hazardous materials is always accompanied by considerable risk that will impact public and environment security. As an efficient and reliable transportation organization, a multimodal service should participate in the transportation of hazardous materials. In this study, we focus on transporting hazardous materials through the multimodal service network and explore the hazardous materials multimodal routing problem from the operational level of network planning. To formulate this problem more practicably, minimizing the total generalized costs of transporting the hazardous materials and the social risk along the planned routes are set as the optimization objectives. Meanwhile, the following formulation characteristics will be comprehensively modelled: (1) specific customer demands; (2) multiple hazardous material flows; (3) capacitated schedule-based rail service and uncapacitated time-flexible road service; and (4) environmental risk constraint. A bi-objective mixed integer nonlinear programming model is first built to formulate the routing problem that combines the formulation characteristics above. Then linear reformations are developed to linearize and improve the initial model so that it can be effectively solved by exact solution algorithms on standard mathematical programming software. By utilizing the normalized weighted sum method, we can generate the Pareto solutions to the bi-objective optimization problem for a specific case. Finally, a large-scale empirical case study from the Beijing–Tianjin–Hebei Region in China is presented to demonstrate the feasibility of the proposed methods in dealing with the practical problem. Various scenarios are also discussed in the case study. PMID:27483294

Bioinspired self-healing materials: lessons from nature

PubMed Central

Cremaldi, Joseph C

2018-01-01

Healing is an intrinsic ability in the incredibly biodiverse populations of the plant and animal kingdoms created through evolution. Plants and animals approach healing in similar ways but with unique pathways, such as damage containment in plants or clotting in animals. After analyzing the examples of healing and defense mechanisms found in living nature, eight prevalent mechanisms were identified: reversible muscle control, clotting, cellular response, layering, protective surfaces, vascular networks or capsules, exposure, and replenishable functional coatings. Then the relationship between these mechanisms, nature’s best (evolutionary) methods of mitigating and healing damage, and existing technology in self-healing materials are described. The goals of this top-level overview are to provide a framework for relating the behavior seen in living nature to bioinspired materials, act as a resource to addressing the limitations/problems with existing materials, and open up new avenues of insight and research into self-healing materials. PMID:29600152

Electron-trapping polycrystalline materials with negative electron affinity.

PubMed

McKenna, Keith P; Shluger, Alexander L

2008-11-01

The trapping of electrons by grain boundaries in semiconducting and insulating materials is important for a wide range of physical problems, for example, relating to: electroceramic materials with applications as sensors, varistors and fuel cells, reliability issues for solar cell and semiconductor technologies and electromagnetic seismic phenomena in the Earth's crust. Surprisingly, considering their relevance for applications and abundance in the environment, there have been few experimental or theoretical studies of the electron trapping properties of grain boundaries in highly ionic materials such as the alkaline earth metal oxides and alkali halides. Here we demonstrate, by first-principles calculations on MgO, LiF and NaCl, a qualitatively new type of electron trapping at grain boundaries. This trapping is associated with the negative electron affinity of these materials and is unusual as the electron is confined in the empty space inside the dislocation cores.

Studies on Experimental Ontology and Knowledge Service Development in Bio-Environmental Engineering

NASA Astrophysics Data System (ADS)

Zhang, Yunliang

2018-01-01

The existing domain-related ontology and information service patterns are analyzed, and the main problems faced by the experimental scheme knowledge service were clarified. The ontology framework model for knowledge service of Bio-environmental Engineering was proposed from the aspects of experimental materials, experimental conditions and experimental instruments, and this ontology will be combined with existing knowledge organization systems to organize scientific and technological literatures, data and experimental schemes. With the similarity and priority calculation, it can improve the related domain research.

Parts, materials, and processes experience summary, volume 2. [design, engineering, and quality control

NASA Technical Reports Server (NTRS)

1973-01-01

This summary provides the general engineering community with the accumulated experience from ALERT reports issued by NASA and the Government-Industry. Data Exchange Program, and related experience gained by Government and industry. It provides expanded information on selected topics by relating the problem area (failure) to the cause, the investigation and findings, the suggestions for avoidance (inspections, screening tests, proper part applications, requirements for manufacturer's plant facilities, etc.), and failure analysis procedures. Diodes, integrated circuits, and transistors are covered in this volume.

Electrical and electronic waste: a global environmental problem.

PubMed

Ramesh Babu, Balakrishnan; Parande, Anand Kuber; Ahmed Basha, Chiya

2007-08-01

The production of electrical and electronic equipment (EEE) is one of the fastest growing global manufacturing activities. This development has resulted in an increase of waste electric and electronic equipment (WEEE). Rapid economic growth, coupled with urbanization and growing demand for consumer goods, has increased both the consumption of EEE and the production of WEEE, which can be a source of hazardous wastes that pose a risk to the environment and to sustainable economic growth. To address potential environmental problems that could stem from improper management of WEEE, many countries and organizations have drafted national legislation to improve the reuse, recycling and other forms of material recovery from WEEE to reduce the amount and types of materials disposed in landfills. Recycling of waste electric and electronic equipment is important not only to reduce the amount of waste requiring treatment, but also to promote the recovery of valuable materials. EEE is diverse and complex with respect to the materials and components used and waste streams from the manufacturing processes. Characterization of these wastes is of paramount importance for developing a cost-effective and environmentally sound recycling system. This paper offers an overview of electrical and e-waste recycling, including a description of how it is generated and classified, strategies and technologies for recovering materials, and new scientific developments related to these activities. Finally, the e-waste recycling industry in India is also discussed.

NASA Composite Materials Development: Lessons Learned and Future Challenges

NASA Technical Reports Server (NTRS)

Tenney, Darrel R.; Davis, John G., Jr.; Pipes, R. Byron; Johnston, Norman

2009-01-01

Composite materials have emerged as the materials of choice for increasing the performance and reducing the weight and cost of military, general aviation, and transport aircraft and space launch vehicles. Major advancements have been made in the ability to design, fabricate, and analyze large complex aerospace structures. The recent efforts by Boeing and Airbus to incorporate composite into primary load carrying structures of large commercial transports and to certify the airworthiness of these structures is evidence of the significant advancements made in understanding and use of these materials in real world aircraft. NASA has been engaged in research on composites since the late 1960 s and has worked to address many development issues with these materials in an effort to ensure safety, improve performance, and improve affordability of air travel for the public good. This research has ranged from synthesis of advanced resin chemistries to development of mathematical analyses tools to reliably predict the response of built-up structures under combined load conditions. The lessons learned from this research are highlighted with specific examples to illustrate the problems encountered and solutions to these problems. Examples include specific technologies related to environmental effects, processing science, fabrication technologies, nondestructive inspection, damage tolerance, micromechanics, structural mechanics, and residual life prediction. The current state of the technology is reviewed and key issues requiring additional research identified. Also, grand challenges to be solved for expanded use of composites in aero structures are identified.

Less Commonly Taught Languages: Resources and Problems.

ERIC Educational Resources Information Center

Centre for Information on Language Teaching, London (England).

This collection of papers from a conference on languages less commonly taught in Britain is concerned with administrative and material problems of teaching these languages. Contents of the publication are: an introduction by G. E. Perren; "Practical Needs" by Anthony Crane; "Problems of Producing Printed Materials" by Rosemary…

A numerical study of different projection-based model reduction techniques applied to computational homogenisation

NASA Astrophysics Data System (ADS)

Soldner, Dominic; Brands, Benjamin; Zabihyan, Reza; Steinmann, Paul; Mergheim, Julia

2017-10-01

Computing the macroscopic material response of a continuum body commonly involves the formulation of a phenomenological constitutive model. However, the response is mainly influenced by the heterogeneous microstructure. Computational homogenisation can be used to determine the constitutive behaviour on the macro-scale by solving a boundary value problem at the micro-scale for every so-called macroscopic material point within a nested solution scheme. Hence, this procedure requires the repeated solution of similar microscopic boundary value problems. To reduce the computational cost, model order reduction techniques can be applied. An important aspect thereby is the robustness of the obtained reduced model. Within this study reduced-order modelling (ROM) for the geometrically nonlinear case using hyperelastic materials is applied for the boundary value problem on the micro-scale. This involves the Proper Orthogonal Decomposition (POD) for the primary unknown and hyper-reduction methods for the arising nonlinearity. Therein three methods for hyper-reduction, differing in how the nonlinearity is approximated and the subsequent projection, are compared in terms of accuracy and robustness. Introducing interpolation or Gappy-POD based approximations may not preserve the symmetry of the system tangent, rendering the widely used Galerkin projection sub-optimal. Hence, a different projection related to a Gauss-Newton scheme (Gauss-Newton with Approximated Tensors- GNAT) is favoured to obtain an optimal projection and a robust reduced model.

Developing material for promoting problem-solving ability through bar modeling technique

NASA Astrophysics Data System (ADS)

Widyasari, N.; Rosiyanti, H.

2018-01-01

This study aimed at developing material for enhancing problem-solving ability through bar modeling technique with thematic learning. Polya’s steps of problem-solving were chosen as the basis of the study. The methods of the study were research and development. The subject of this study were five teen students of the fifth grade of Lab-school FIP UMJ elementary school. Expert review and student’ response analysis were used to collect the data. Furthermore, the data were analyzed using qualitative descriptive and quantitative. The findings showed that material in theme “Selalu Berhemat Energi” was categorized as valid and practical. The validity was measured by using the aspect of language, contents, and graphics. Based on the expert comments, the materials were easy to implement in the teaching-learning process. In addition, the result of students’ response showed that material was both interesting and easy to understand. Thus, students gained more understanding in learning problem-solving.

Prepreg effects on honeycomb composite manufacturing

NASA Astrophysics Data System (ADS)

Martin, Cary Joseph

Fiber reinforced composites offer many advantages over traditional materials and are widely utilized in aerospace applications. Advantages include a high stiffness to weight ratio and excellent fatigue resistance. However, the pace of new implementation is slow. The manufacturing processes used to transform composite intermediates into final products are poorly understood and are a source of much variability. This limits new implementation and increases the manufacturing costs of existing designs. One such problem is honeycomb core crush, in which a core-stiffened structure collapses during autoclave manufacture, making the structure unusable and increasing the overall manufacturing cost through increased scrap rates. Consequently, the major goal of this research was to investigate the scaling of core crush from prepreg process-structure-property relations to commercial composite manufacture. The material dependent nature of this defect was of particular interest. A methodology and apparatus were developed to measure the frictional resistance of prepreg materials under typical processing conditions. Through a characterization of commercial and experimental prepregs, it was found that core crush behavior was the result of differences in prepreg frictional resistance. This frictional resistance was related to prepreg morphology and matrix rheology and elasticity. Resin composition and prepreg manufacturing conditions were also found to affect manufacturing behavior. Mechanical and dimensional models were developed and demonstrated utility for predicting this crushing behavior. Collectively, this work explored and identified the process-structure-property relations as they relate to the manufacture of composite materials and suggested several avenues by which manufacturing-robust materials may be developed.

Designing Biomimetic Materials from Marine Organisms.

PubMed

Nichols, William T

2015-01-01

Two biomimetic design approaches that apply biological solutions to engineering problems are discussed. In the first case, motivation comes from an engineering problem and the key challenge is to find analogous biological functions and map them into engineering materials. We illustrate with an example of water pollution remediation through appropriate design of a biomimetic sponge. In the second case, a biological function is already known and the challenge is to identify the appropriate engineering problem. We demonstrate the biological approach with marine diatoms that control energy and materials at their surface providing inspiration for a number of engineering applications. In both cases, it is essential to select materials and structures at the nanoscale to control energy and materials flows at interfaces.

Inverse problems in complex material design: Applications to non-crystalline solids

NASA Astrophysics Data System (ADS)

Biswas, Parthapratim; Drabold, David; Elliott, Stephen

The design of complex amorphous materials is one of the fundamental problems in disordered condensed-matter science. While impressive developments of ab-initio simulation methods during the past several decades have brought tremendous success in understanding materials property from micro- to mesoscopic length scales, a major drawback is that they fail to incorporate existing knowledge of the materials in simulation methodologies. Since an essential feature of materials design is the synergy between experiment and theory, a properly developed approach to design materials should be able to exploit all available knowledge of the materials from measured experimental data. In this talk, we will address the design of complex disordered materials as an inverse problem involving experimental data and available empirical information. We show that the problem can be posed as a multi-objective non-convex optimization program, which can be addressed using a number of recently-developed bio-inspired global optimization techniques. In particular, we will discuss how a population-based stochastic search procedure can be used to determine the structure of non-crystalline solids (e.g. a-SiH, a-SiO2, amorphous graphene, and Fe and Ni clusters). The work is partially supported by NSF under Grant Nos. DMR 1507166 and 1507670.

Modeling Thermal Noise from Crystaline Coatings for Gravitational-Wave Detectors

NASA Astrophysics Data System (ADS)

Demos, Nicholas; Lovelace, Geoffrey; LSC Collaboration

2016-03-01

The sensitivity of current and future ground-based gravitational-wave detectors are, in part, limited in sensitivity by Brownian and thermoelastic noise in each detector's mirror substrate and coating. Crystalline mirror coatings could potentially reduce thermal noise, but thermal noise is challenging to model analytically in the case of crystalline materials. Thermal noise can be modeled using the fluctuation-dissipation theorem, which relates thermal noise to an auxiliary elastic problem. In this poster, I will present results from a new code that numerically models thermal noise by numerically solving the auxiliary elastic problem for various types of crystalline mirror coatings. The code uses a finite element method with adaptive mesh refinement to model the auxiliary elastic problem which is then related to thermal noise. I will present preliminary results for a crystal coating on a fused silica substrate of varying sizes and elastic properties. This and future work will help develop the next generation of ground-based gravitational-wave detectors.

Orphan Status, HIV Risk Behavior, and Mental Health Among Adolescents in Rural Kenya

PubMed Central

Drabkin, Anya S.; Stashko, Allison L.; Broverman, Sherryl A.; Ogwang-Odhiambo, Rose A.; Sikkema, Kathleen J.

2012-01-01

Objective To examine orphan status, mental health, social support, and HIV risk among adolescents in rural Kenya. Methods Randomly selected adolescents aged 10–18 years completed surveys assessing sexual activity, sex-related beliefs and self-efficacy, mental health, social support, caregiver–child communication, time since parental death, and economic resources. Analysis of covariance and regression analyses compared orphans and nonorphans; orphan status was tested as a moderator between well-being and HIV risk. Results Orphans reported poorer mental health, less social support, and fewer material resources. They did not differ from nonorphans on HIV risk indicators. Longer time since parental death was associated with poorer outcomes. In moderator analyses, emotional problems and poorer caregiver–youth communication were more strongly associated with lower sex-related self-efficacy for orphans. Conclusions Orphans are at higher risk for psychosocial problems. These problems may affect orphans’ self-efficacy for safer sex practices more than nonorphans. Decreased HIV risk could be one benefit of psychosocial interventions for orphans. PMID:22728899

Orphan status, HIV risk behavior, and mental health among adolescents in rural Kenya.

PubMed

Puffer, Eve S; Drabkin, Anya S; Stashko, Allison L; Broverman, Sherryl A; Ogwang-Odhiambo, Rose A; Sikkema, Kathleen J

2012-09-01

To examine orphan status, mental health, social support, and HIV risk among adolescents in rural Kenya. Randomly selected adolescents aged 10-18 years completed surveys assessing sexual activity, sex-related beliefs and self-efficacy, mental health, social support, caregiver-child communication, time since parental death, and economic resources. Analysis of covariance and regression analyses compared orphans and nonorphans; orphan status was tested as a moderator between well-being and HIV risk. Orphans reported poorer mental health, less social support, and fewer material resources. They did not differ from nonorphans on HIV risk indicators. Longer time since parental death was associated with poorer outcomes. In moderator analyses, emotional problems and poorer caregiver-youth communication were more strongly associated with lower sex-related self-efficacy for orphans. Orphans are at higher risk for psychosocial problems. These problems may affect orphans' self-efficacy for safer sex practices more than nonorphans. Decreased HIV risk could be one benefit of psychosocial interventions for orphans.

Fibrous materials on polyhydroxybutyrate and ferric iron (III)-based porphyrins basis: physical-chemical and antibacterial properties

NASA Astrophysics Data System (ADS)

Olkhov, A.; Lobanov, A.; Staroverova, O.; Tyubaeva, P.; Zykova, A.; Pantyukhov, P.; Popov, A.; Iordanskii, A.

2017-02-01

Ferric iron (III)-based complexes with porphyrins are the homogenous catalysts of auto-oxidation of several biogenic substances. The most perspective carrier for functional low-molecular substances is the polymer fibers with nano-dimensional parameters. Application of natural polymers, poly-(3-hydroxybutyrate) or polylactic acid for instance, makes possible to develop fiber and matrice systems to solve ecological problem in biomedicine The aim of the article is to obtain fibrous material on poly-(3-hydroxybutyrate) and ferric iron (III)-based porphyrins basis and to examine its physical-chemical and antibacterial properties. The work is focused on possibility to apply such material to biomedical purposes. Microphotographs of obtained material showed that addition of 1% wt. ferric iron (III)-based porphyrins to PHB led to increased average diameter and disappeared spindly structures in comparison with initial PHB. Biological tests of nonwoven fabrics showed that fibers, containing ferric iron (III)-based tetraphenylporphyrins, were active in relation to bacterial test-cultures. It was found that materials on polymer and metal complexes with porphyrins basis can be applied to production of decontamination equipment in relation to pathogenic and opportunistic microorganisms.

Application of grey-fuzzy approach in parametric optimization of EDM process in machining of MDN 300 steel

NASA Astrophysics Data System (ADS)

Protim Das, Partha; Gupta, P.; Das, S.; Pradhan, B. B.; Chakraborty, S.

2018-01-01

Maraging steel (MDN 300) find its application in many industries as it exhibits high hardness which are very difficult to machine material. Electro discharge machining (EDM) is an extensively popular machining process which can be used in machining of such materials. Optimization of response parameters are essential for effective machining of these materials. Past researchers have already used Taguchi for obtaining the optimal responses of EDM process for this material with responses such as material removal rate (MRR), tool wear rate (TWR), relative wear ratio (RWR), and surface roughness (SR) considering discharge current, pulse on time, pulse off time, arc gap, and duty cycle as process parameters. In this paper, grey relation analysis (GRA) with fuzzy logic is applied to this multi objective optimization problem to check the responses by an implementation of the derived parametric setting. It was found that the parametric setting derived by the proposed method results in better a response than those reported by the past researchers. Obtained results are also verified using the technique for order of preference by similarity to ideal solution (TOPSIS). The predicted result also shows that there is a significant improvement in comparison to the results of past researchers.

Home Economics Reading Skills: Problems and Selected References.

ERIC Educational Resources Information Center

Cranney, A. Garr; And Others

Home economics presents at least eight problems to secondary school reading teachers. These problems include poor readers, difficult reading material, lack of reading materials, teachers' lack of training in reading instruction, scarce information about home economics for reading teachers, diversity of the home economics field (requiring a wide…

[Research on the Application of Lean Management in Medical Consumables Material Logistics Management].

PubMed

Yang, Chai; Zhang, Wei; Gu, Wei; Shen, Aizong

2016-11-01

Solve the problems of high cost, low utilization rate of resources, low medical care quality problem in medical consumables material logistics management for scientific of medical consumables management. Analysis of the problems existing in the domestic medical consumables material logistics management in hospital, based on lean management method, SPD(Supply, Processing, Distribution) for specific applications, combined HBOS(Hospital Business Operation System), HIS (Hospital Information System) system for medical consumables material management. Achieve the lean management in medical consumables material purchase, warehouse construction, push, clinical use and retrospect. Lean management in medical consumables material can effectively control the cost in logistics management, optimize the alocation of resources, liberate unnecessary time of medical staff, improve the quality of medical care. It is a scientific management method.

Correlates of gambling on high-school grounds

PubMed Central

Foster, Dawn W.; Hoff, Rani A.; Pilver, Corey E.; Yau, Yvonne H. C.; Steinberg, Marvin A.; Wampler, Jeremy; Krishnan-Sarin, Suchitra; Potenza, Marc N.

2015-01-01

Objective This study examined adolescent gambling on school grounds (GS+) and how such behavior was associated with gambling-related attitudes. Further, we examined whether GS+ moderated associations between at-risk problem-gambling (ARPG) and gambling behaviors related to gambling partners. Method Participants were 1988 high-school students who completed survey materials. Demographic, perceptions, attitudes, and gambling variables were stratified by problem-gambling severity (ARPG versus recreational gambling) and GS+ status. Chi-square and adjusted logistic regression models were used to examine relationships among study variables. Results Nearly 40% (39.58%) of students reported past-year GS+, with 12.91% of GS+ students, relative to 2.63% of those who did not report gambling on school grounds (GS), meeting DSM-IV criteria for pathological gambling (p<0.0001). In comparison to GS- students, GS+ students were more likely to report poorer academic achievement and more permissive attitudes towards gambling behaviors. Weaker links in GS+ students, in comparison with GS-, students, were observed between problem-gambling severity and gambling with family members (interaction odds ratio (IOR)=0.60; 95%CI=0.39–0.92) and gambling with friends (IOR=0.21; 95%CI=0.11–0.39). Conclusions GS+ is common and associated with pathological gambling and more permissive attitudes towards gambling. The finding that GS+ (relative to GS-) youth show differences in how problem-gambling is related to gambling partners (friends and family) warrants further investigation regarding whether and how peer and familial interactions might be improved to diminish youth problem-gambling severity. The high frequency of GS+ and its relationship with ARPG highlight a need for school administrators and personnel to consider interventions that target school-based gambling. PMID:26232102

MED9/368: Health education over Internet: Is there a special way for smaller language groups?

PubMed Central

Aru, J

1999-01-01

Health education over resources, that use English, German and French language, is a rapidly growing area of medicine within the World Wide Web. Multiple gateways and portal servers have been set up to guide people within the diversity of materials available. For smaller language groups the situation is quite different: there is a lack of information in even the basic medical education topics. The question is: how to fill the missing gaps. Principally two different ways are possible: Translating materials from English, German, French and other "big" language groups. Generating original Internet-based texts for "smaller" language group When using the first, possibility of problems related to copyright and proper translating occur. When using the second approach, the quality of materials could suffer. As an example, the homepage for health education www.doctus.ee is discussed in detail. This homepage includes materials about the health care system, basic health topics, main diseases and also a questionnaire for consulting one's health problems with a doctor. A year's experience running this health education Web site in Estonian has brought to following conclusions: For translations a link for originals should be included. With original Estonian texts copyright questions are frequent. Guidance is frequently needed for translated texts. Health consultations over Internet should be legally regulated

ICME — A Mere Coupling of Models or a Discipline of Its Own?

NASA Astrophysics Data System (ADS)

Bambach, Markus; Schmitz, Georg J.; Prahl, Ulrich

Technically, ICME — Integrated computational materials engineering — is an approach for solving advanced engineering problems related to the design of new materials and processes by combining individual materials and process models. The combination of models by now is mainly achieved by manual transformation of the output of a simulation to form the input to a subsequent one. This subsequent simulation is either performed at a different length scale or constitutes a subsequent step along the process chain. Is ICME thus just a synonym for the coupling of simulations? In fact, most ICME publications up to now are examples of the joint application of selected models and software codes to a specific problem. However, from a systems point of view, the coupling of individual models and/or software codes across length scales and along material processing chains leads to highly complex meta-models. Their viability has to be ensured by joint efforts from science, industry, software developers and independent organizations. This paper identifies some developments that seem necessary to make future ICME simulations viable, sustainable and broadly accessible and accepted. The main conclusion is that ICME is more than a multi-disciplinary subject but a discipline of its own, for which a generic structural framework has to be elaborated and established.

Impact induced depolarization of ferroelectric materials

NASA Astrophysics Data System (ADS)

Agrawal, Vinamra; Bhattacharya, Kaushik

2018-06-01

We study the large deformation dynamic behavior and the associated nonlinear electro-thermo-mechanical coupling exhibited by ferroelectric materials in adiabatic environments. This is motivated by a ferroelectric generator which involves pulsed power generation by loading the ferroelectric material with a shock, either by impact or a blast. Upon impact, a shock wave travels through the material inducing a ferroelectric to nonpolar phase transition giving rise to a large voltage difference in an open circuit situation or a large current in a closed circuit situation. In the first part of this paper, we provide a general continuum mechanical treatment of the situation assuming a sharp phase boundary that is possibly charged. We derive the governing laws, as well as the driving force acting on the phase boundary. In the second part, we use the derived equations and a particular constitutive relation that describes the ferroelectric to nonpolar phase transition to study a uniaxial plate impact problem. We develop a numerical method where the phase boundary is tracked but other discontinuities are captured using a finite volume method. We compare our results with experimental observations to find good agreement. Specifically, our model reproduces the observed exponential rise of charge as well as the resistance dependent Hugoniot. We conclude with a parameter study that provides detailed insight into various aspects of the problem.

Lightweight porous plastic plaque. [nickel cadmium batteries

NASA Technical Reports Server (NTRS)

Reid, M.

1978-01-01

The porosity and platability of various materials were investigated to determine a suitable substrate for nickel-plated electrodes. Immersion, ultrasonics, and flow-through plating techniques were tried using nonproprietary formulations, and proprietary phosphide and boride baths. Modifications to the selected material include variations in formulation and treatment, carbon loading to increase conductivity, and the incorporation of a grid. Problems to be solved relate to determining conductivities and porosities as a function of amount of nickel plated on the plastics; loading; charge and discharge curves of electrodes at different current densities; cell performance; and long-term degradation of electrodes.

Heat sink structural design concepts for a hypersonic research airplane

NASA Technical Reports Server (NTRS)

Taylor, A. H.; Jackson, L. R.

1977-01-01

Hypersonic research aircraft design requires careful consideration of thermal stresses. This paper relates some of the problems in a heat sink structural design that can be avoided by appropriate selection of design options including material selection, design concepts, and load paths. Data on several thermal loading conditions are presented on various conventional designs including bulkheads, longerons, fittings, and frames. Results indicate that conventional designs are inadequate and that acceptable designs are possible by incorporating innovative design practices. These include nonintegral pressure compartments, ball-jointed links to distribute applied loads without restraining the thermal expansion, and material selections based on thermal compatibility.

Books and the Teen-age Reader: A Guide for Teachers, Librarians and Parents.

ERIC Educational Resources Information Center

Carlsen, G. Robert

Indicating the need for reading materials to be related to the teenager's problems and interests as well as consistent with the stages of reading development, this book suggests ways to provide good reading experiences for young people in an effort to helf them enjoy reading. It calls for a rational approach to the adolescent's interest in…

An Inexpensive 2-D and 3-D Model of the Sarcomere as a Teaching Aid

ERIC Educational Resources Information Center

Rios, Vitor Passos; Bonfim, Vanessa Maria Gomes

2013-01-01

To address a common problem of teaching the sliding filament theory (that is, students have difficulty in visualizing how the component proteins of the sarcomere differ, how they organize themselves into a single working unit, and how they function in relation to each other), we have devised a simple model, with inexpensive materials, to be built…

The Influence of Different Representations on Solving Concentration Problems at Elementary School

NASA Astrophysics Data System (ADS)

Liu, Chia-Ju; Shen, Ming-Hsun

2011-10-01

This study investigated the students' learning process of the concept of concentration at the elementary school level in Taiwan. The influence of different representational types on the process of proportional reasoning was also explored. The participants included nineteen third-grade and eighteen fifth-grade students. Eye-tracking technology was used in conducting the experiment. The materials were adapted from Noelting's (1980a) "orange juice test" experiment. All problems on concentration included three stages (the intuitive, the concrete operational, and the formal operational), and each problem was displayed in iconic and symbolic representations. The data were collected through eye-tracking technology and post-test interviews. The results showed that the representational types influenced students' solving of concentration problems. Furthermore, the data on eye movement indicated that students used different strategies or rules to solve concentration problems at the different stages of the problems with different representational types. This study is intended to contribute to the understanding of elementary school students' problem-solving strategies and the usability of eye-tracking technology in related studies.

IMPACTS OF MATERIAL SUBSTITUTION IN AUTOMOBILE MANUFACTURE ON RESOURCE RECOVERY. VOLUME II. APPENDICES A-E

EPA Science Inventory

Probable changes in the mix of materials used to manufacture automobiles were examined to determine if economic or technical problems in recycling could arise such that the 'abandoned automobile problem' would be resurrected. Future trends in materials composition of the automobi...

Nanostructured mesoporous materials for lithium-ion battery applications

NASA Astrophysics Data System (ADS)

Balaya, P.; Saravanan, K.; Hariharan, S.; Ramar, V.; Lee, H. S.; Kuezma, M.; Devaraj, S.; Nagaraju, D. H.; Ananthanarayanan, K.; Mason, C. W.

2011-06-01

The Energy crisis happens to be one of the greatest challenges we are facing today. In this view, much effort has been made in developing new, cost effective, environmentally friendly energy conversion and storage devices. The performance of such devices is fundamentally related to material properties. Hence, innovative materials engineering is important in solving the energy crisis problem. One such innovation in materials engineering is porous materials for energy storage. Porous electrode materials for lithium-ion batteries (LIBs) offer a high degree of electrolyte-electrode wettability, thus enhancing the electrochemical activity within the material. Among the porous materials, mesoporous materials draw special attention, owing to shorter diffusion lengths for Li+ and electronic movement. Nanostructured mesoporous materials also offer better packing density compared to their nanostructured counterparts such as nanopowders, nanowires, nanotubes etc., thus opening a window for developing electrode materials with high volumetric energy densities. This would directly translate into a scenario of building batteries which are much lighter than today's commercial LIBs. In this article, the authors present a simple, soft template approach for preparing both cathode and anode materials with high packing density for LIBs. The impact of porosity on the electrochemical storage performance is highlighted.

Paper recycling framework, the "Wheel of Fiber".

PubMed

Ervasti, Ilpo; Miranda, Ruben; Kauranen, Ilkka

2016-06-01

At present, there is no reliable method in use that unequivocally describes paper industry material flows and makes it possible to compare geographical regions with each other. A functioning paper industry Material Flow Account (MFA) that uses uniform terminology and standard definitions for terms and structures is necessary. Many of the presently used general level MFAs, which are called frameworks in this article, stress the importance of input and output flows but do not provide a uniform picture of material recycling. Paper industry is an example of a field in which recycling plays a key role. Additionally, terms related to paper industry recycling, such as collection rate, recycling rate, and utilization rate, are not defined uniformly across regions and time. Thus, reliably comparing material recycling activity between geographical regions or calculating any regional summaries is difficult or even impossible. The objective of this study is to give a partial solution to the problem of not having a reliable method in use that unequivocally describes paper industry material flows. This is done by introducing a new material flow framework for paper industry in which the flow and stage structure supports the use of uniform definitions for terms related to paper recycling. This new framework is termed the Detailed Wheel of Fiber. Copyright © 2016 Elsevier Ltd. All rights reserved.

Transient analysis of a thermal storage unit involving a phase change material

NASA Technical Reports Server (NTRS)

Griggs, E. I.; Pitts, D. R.; Humphries, W. R.

1974-01-01

The transient response of a single cell of a typical phase change material type thermal capacitor has been modeled using numerical conductive heat transfer techniques. The cell consists of a base plate, an insulated top, and two vertical walls (fins) forming a two-dimensional cavity filled with a phase change material. Both explicit and implicit numerical formulations are outlined. A mixed explicit-implicit scheme which treats the fin implicity while treating the phase change material explicitly is discussed. A band algorithmic scheme is used to reduce computer storage requirements for the implicit approach while retaining a relatively fine grid. All formulations are presented in dimensionless form thereby enabling application to geometrically similar problems. Typical parametric results are graphically presented for the case of melting with constant heat input to the base of the cell.

Safety issues and new rapid detection methods in traditional Chinese medicinal materials

PubMed Central

Wang, Lili; Kong, Weijun; Yang, Meihua; Han, Jianping; Chen, Shilin

2015-01-01

The safety of traditional Chinese medicine (TCM) is a major strategic issue that involves human health. With the continuous improvement in disease prevention and treatment, the export of TCM and its related products has increased dramatically in China. However, the frequent safety issues of Chinese medicine have become the ‘bottleneck’ impeding the modernization of TCM. It was proved that mycotoxins seriously affect TCM safety; the pesticide residues of TCM are a key problem in TCM international trade; adulterants have also been detected, which is related to market circulation. These three factors have greatly affected TCM safety. In this study, fast, highly effective, economically-feasible and accurate detection methods concerning TCM safety issues were reviewed, especially on the authenticity, mycotoxins and pesticide residues of medicinal materials. PMID:26579423

A versatile localization system for microscopic multiparametric analysis of cells.

PubMed

Thaw, H H; Rundquist, I; Johansson, U; Svensson, I; Collins, V P

1983-03-01

A new, simple and relatively inexpensive electronic digital position readout (DPRO) system which can be applied to the rapid localization and recovery of microscopic material is described. It is based upon a commercially available digital position readout system which is routinely utilized by industry for small machine tools and measuring equipment. This has been mounted onto the stage of various microscopic instrumentation to provide X and Y coordinates relative to an arbitrary reference point. The integration of small computers interfaced to scanning interferometric, microdensitometric and fluorescence microscopes were used to demonstrate the reliability, versatility and ease of application of this system to problems of multiparametric measurements and analysis of cultured cells. The system may be expanded and applied to clinical material to obtain automatized, multiparametric measurements of cells in haematology and clinical cytology.

Design solutions for the solar cell interconnect fatigue fracture problem

NASA Technical Reports Server (NTRS)

Mon, G. R.; Ross, R. G., Jr.

1982-01-01

Mechanical fatigue of solar cell interconnects is a major failure mechanism in photovoltaic arrays. A comprehensive approach to the reliability design of interconnects, together with extensive design data for the fatigue properties of copper interconnects, has been published. This paper extends the previous work, developing failure prediction (fatigue) data for additional interconnect material choices, including aluminum and a variety of copper-Invar and copper-steel claddings. An improved global fatigue function is used to model the probability-of-failure statistics of each material as a function of level and number of cycles of applied strain. Life-cycle economic analyses are used to evaluate the relative merits of each material choce. The copper-Invar clad composites demonstrate superior performance over pure copper. Aluminum results are disappointing.

Controllable film densification and interface flatness for high-performance amorphous indium oxide based thin film transistors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ou-Yang, Wei, E-mail: OUYANG.Wei@nims.go.jp, E-mail: TSUKAGOSHI.Kazuhito@nims.go.jp; Mitoma, Nobuhiko; Kizu, Takio

2014-10-20

To avoid the problem of air sensitive and wet-etched Zn and/or Ga contained amorphous oxide transistors, we propose an alternative amorphous semiconductor of indium silicon tungsten oxide as the channel material for thin film transistors. In this study, we employ the material to reveal the relation between the active thin film and the transistor performance with aid of x-ray reflectivity study. By adjusting the pre-annealing temperature, we find that the film densification and interface flatness between the film and gate insulator are crucial for achieving controllable high-performance transistors. The material and findings in the study are believed helpful for realizingmore » controllable high-performance stable transistors.« less

The current status of materials for posterior composite restorations: the advent of low shrink.

PubMed

Burke, F J trevor; Palin, W M; James, A; Mackenzie, L; Sands, P

2009-09-01

Polymerization contraction, and the stresses associated with this, have presented problems with resin composite materials, particularly when used to restore cavities in posterior teeth. This paper summarizes the problems associated with polymerization contraction and examines methods used to overcome this, in particular, by the use of materials which have reduced percentage contraction when compared with traditional materials. Use of a material with reduced polymerization contraction should lead to simpler restoration placement.

Coated woven materials and method of preparation

DOEpatents

McCreary, W.J.; Carroll, D.W.

Coating of woven materials so that not only the outer surfaces are coated has been a problem. Now, a solution to that problem is by coating with materials, with metals or with pyrolytic carbon. Materials are deposited in Chemical Vapor Deposition (CND) reactions using a fluidized bed so that the porosity of the woven materials is retained and the tiny filaments which make up the strands which are woven (including inner as well as outer filaments) are substantially uniformly coated.

Biodynamics of deformable human body motion

NASA Technical Reports Server (NTRS)

Strauss, A. M.; Huston, R. L.

1976-01-01

The objective is to construct a framework wherein the various models of human biomaterials fit in order to describe the biodynamic response of the human body. The behavior of the human body in various situations, from low frequency, low amplitude vibrations to impact loadings in automobile and aircraft crashes, is very complicated with respect to all aspects of the problem: materials, geometry and dynamics. The materials problem is the primary concern, but the materials problem is intimately connected with geometry and dynamics.

Green material selection for sustainability: A hybrid MCDM approach.

PubMed

Zhang, Honghao; Peng, Yong; Tian, Guangdong; Wang, Danqi; Xie, Pengpeng

2017-01-01

Green material selection is a crucial step for the material industry to comprehensively improve material properties and promote sustainable development. However, because of the subjectivity and conflicting evaluation criteria in its process, green material selection, as a multi-criteria decision making (MCDM) problem, has been a widespread concern to the relevant experts. Thus, this study proposes a hybrid MCDM approach that combines decision making and evaluation laboratory (DEMATEL), analytical network process (ANP), grey relational analysis (GRA) and technique for order performance by similarity to ideal solution (TOPSIS) to select the optimal green material for sustainability based on the product's needs. A nonlinear programming model with constraints was proposed to obtain the integrated closeness index. Subsequently, an empirical application of rubbish bins was used to illustrate the proposed method. In addition, a sensitivity analysis and a comparison with existing methods were employed to validate the accuracy and stability of the obtained final results. We found that this method provides a more accurate and effective decision support tool for alternative evaluation or strategy selection.

Green material selection for sustainability: A hybrid MCDM approach

PubMed Central

Zhang, Honghao; Peng, Yong; Tian, Guangdong; Wang, Danqi; Xie, Pengpeng

2017-01-01

Green material selection is a crucial step for the material industry to comprehensively improve material properties and promote sustainable development. However, because of the subjectivity and conflicting evaluation criteria in its process, green material selection, as a multi-criteria decision making (MCDM) problem, has been a widespread concern to the relevant experts. Thus, this study proposes a hybrid MCDM approach that combines decision making and evaluation laboratory (DEMATEL), analytical network process (ANP), grey relational analysis (GRA) and technique for order performance by similarity to ideal solution (TOPSIS) to select the optimal green material for sustainability based on the product's needs. A nonlinear programming model with constraints was proposed to obtain the integrated closeness index. Subsequently, an empirical application of rubbish bins was used to illustrate the proposed method. In addition, a sensitivity analysis and a comparison with existing methods were employed to validate the accuracy and stability of the obtained final results. We found that this method provides a more accurate and effective decision support tool for alternative evaluation or strategy selection. PMID:28498864

The indoor air we breathe.

PubMed Central

Oliver, L C; Shackleton, B W

1998-01-01

Increasingly recognized as a potential public health problem since the outbreak of Legionnaire's disease in Philadelphia in 1976, polluted indoor air has been associated with health problems that include asthma, sick building syndrome, multiple chemical sensitivity, and hypersensitivity pneumonitis. Symptoms are often nonspecific and include headache, eye and throat irritation, chest tightness and shortness of breath, and fatigue. Air-borne contaminants include commonly used chemicals, vehicular exhaust, microbial organisms, fibrous glass particles, and dust. Identified causes include defective building design and construction, aging of buildings and their ventilation systems, poor climate control, inattention to building maintenance. A major contributory factor is the explosion in the use of chemicals in building construction and furnishing materials over the past four decades. Organizational issues and psychological variables often contribute to the problem and hinder its resolution. This article describes the health problems related to poor indoor air quality and offers solutions. Images p398-a p399-a PMID:9769764

New sets of eigenvalues in inverse scattering for inhomogeneous media and their determination from scattering data

NASA Astrophysics Data System (ADS)

Audibert, Lorenzo; Cakoni, Fioralba; Haddar, Houssem

2017-12-01

In this paper we develop a general mathematical framework to determine interior eigenvalues from a knowledge of the modified far field operator associated with an unknown (anisotropic) inhomogeneity. The modified far field operator is obtained by subtracting from the measured far field operator the computed far field operator corresponding to a well-posed scattering problem depending on one (possibly complex) parameter. Injectivity of this modified far field operator is related to an appropriate eigenvalue problem whose eigenvalues can be determined from the scattering data, and thus can be used to obtain information about material properties of the unknown inhomogeneity. We discuss here two examples of such modification leading to a Steklov eigenvalue problem, and a new type of the transmission eigenvalue problem. We present some numerical examples demonstrating the viability of our method for determining the interior eigenvalues form far field data.

Interval MULTIMOORA method with target values of attributes based on interval distance and preference degree: biomaterials selection

NASA Astrophysics Data System (ADS)

Hafezalkotob, Arian; Hafezalkotob, Ashkan

2017-06-01

A target-based MADM method covers beneficial and non-beneficial attributes besides target values for some attributes. Such techniques are considered as the comprehensive forms of MADM approaches. Target-based MADM methods can also be used in traditional decision-making problems in which beneficial and non-beneficial attributes only exist. In many practical selection problems, some attributes have given target values. The values of decision matrix and target-based attributes can be provided as intervals in some of such problems. Some target-based decision-making methods have recently been developed; however, a research gap exists in the area of MADM techniques with target-based attributes under uncertainty of information. We extend the MULTIMOORA method for solving practical material selection problems in which material properties and their target values are given as interval numbers. We employ various concepts of interval computations to reduce degeneration of uncertain data. In this regard, we use interval arithmetic and introduce innovative formula for interval distance of interval numbers to create interval target-based normalization technique. Furthermore, we use a pairwise preference matrix based on the concept of degree of preference of interval numbers to calculate the maximum, minimum, and ranking of these numbers. Two decision-making problems regarding biomaterials selection of hip and knee prostheses are discussed. Preference degree-based ranking lists for subordinate parts of the extended MULTIMOORA method are generated by calculating the relative degrees of preference for the arranged assessment values of the biomaterials. The resultant rankings for the problem are compared with the outcomes of other target-based models in the literature.

Research Utilizing Problem Solving (RUPS) - Classroom Version. Description of Teacher Inservice Education Materials.

ERIC Educational Resources Information Center

National Education Association, Washington, DC. Project on Utilization of Inservice Education R & D Outcomes.

The workshop instructional materials described here are designed to try out a systematic problem solving process as a way of working toward improvements in the school setting. Topics include diagnosis using force field technique, small group dynamics, planning for action, and planning a RUPS (Research Using Problem Solving) project. This…

Effect of a "Look-Ahead" Problem on Undergraduate Engineering Students' Concept Comprehension

ERIC Educational Resources Information Center

Goodman, Kevin; Davis, Julian; McDonald, Thomas

2016-01-01

In an effort to motivate undergraduate engineering students to prepare for class by reviewing material before lectures, a "Look-Ahead" problem was utilized. Students from two undergraduate engineering courses; Statics and Electronic Circuits, were assigned problems from course material that had not yet been covered in class. These…

Shifting orders among suppliers considering risk, price and transportation cost

NASA Astrophysics Data System (ADS)

Revitasari, C.; Pujawan, I. N.

2018-04-01

Supplier order allocation is an important supply chain decision for an enterprise. It is related to the supplier’s function as a raw material provider and other supporting materials that will be used in production process. Most of works on order allocation has been based on costs and other supply chain performance, but very limited of them taking risks into consideration. In this paper we address the problem of order allocation of a single commodity sourced from multiple suppliers considering supply risks in addition to the attempt of minimizing transportation costs. The supply chain risk was investigated and a procedure was proposed in the risk mitigation phase as a form of risk profile. The objective including risk profile in order allocation is to maximize the product flow from a risky supplier to a relatively less risky supplier. The proposed procedure is applied to a sugar company. The result suggests that order allocations should be maximized to suppliers that have a relatively low risk and minimized to suppliers that have a relatively larger risks.

Constitutive relations in multidimensional isotropic elasticity and their restrictions to subspaces of lower dimensions

NASA Astrophysics Data System (ADS)

Georgievskii, D. V.

2017-07-01

The mechanical meaning and the relationships among material constants in an n-dimensional isotropic elastic medium are discussed. The restrictions of the constitutive relations (Hooke's law) to subspaces of lower dimension caused by the conditions that an m-dimensional strain state or an m-dimensional stress state (1 ≤ m < n) is realized in the medium. Both the terminology and the general idea of the mathematical construction are chosen by analogy with the case n = 3 and m = 2, which is well known in the classical plane problem of elasticity theory. The quintuples of elastic constants of the same medium that enter both the n-dimensional relations and the relations written out for any m-dimensional restriction are expressed in terms of one another. These expressions in terms of the known constants, for example, of a three-dimensional medium, i.e., the classical elastic constants, enable us to judge the material properties of this medium immersed in a space of larger dimension.

Ion figuring of large prototype mirror segments for the E-ELT

NASA Astrophysics Data System (ADS)

Ghigo, M.; Vecchi, G.; Basso, S.; Citterio, O.; Civitani, M.; Mattaini, E.; Pareschi, G.; Sironi, G.

2014-07-01

At INAF-Astronomical Observatory of Brera a study is under way to explore the problems related to the ion beam figuring of full scale Zerodur hexagonal mirrors of M1 for the European Extremely Large Telescope (E-ELT), having size of 1.4 m corner to corner. During this study it is initially foreseen the figuring of a scaled down version mirror of the same material having size of 1 m corner to corner to assess the relevant figuring problems and issues. This specific mirror has a radius of curvature of 3 m, which allows for easy interferometric measurement. A mechanical support was designed to minimize its deformations due to the gravity. The Ion Beam Figuring Facility used for this study has been recently completed in the Brera Observatory and has a figuring area of 140 cm x 170 cm. It employs a Kaufman ion source having 50 mm grids mounted on three axis. This system has been designed and developed to be autonomous and self-monitoring during the figuring process. The software and the mathematical tools used to compute the dwell time solution have been developed at INAF-OAB as well. Aim of this study is the estimation and optimization of the time requested to correct the surface adopting strategies to mitigate the well-known thermal problems related to the Zerodur material. In this paper, the results obtained figuring the 1 m corner-to-corner test segment are reported.

False memories from survival processing make better primes for problem-solving.

PubMed

Garner, Sarah R; Howe, Mark L

2014-01-01

Previous research has demonstrated that participants remember significantly more survival-related information and more information that is processed for its survival relevance. Recent research has also shown that survival materials and processing result in more false memories, ones that are adaptive inasmuch as they prime solutions to insight-based problems. Importantly, false memories for survival-related information facilitate problem solving more than false memories for other types of information. The present study explores this survival advantage using an incidental rather than intentional memory task. Here participants rated information either in the context of its importance to a survival-processing scenario or to moving to a new house. Following this, participants solved a number of compound remote associate tasks (CRATs), half of which had the solution primed by false memories that were generated during the processing task. Results showed that (a) CRATs were primed by false memories in this incidental task, with participants solving significantly more CRATs when primed than when unprimed, (b) this effect was greatest when participants rated items for survival than moving, and (c) processing items for a survival scenario improved overall problem-solving performance even when specific problems themselves were not primed. Results are discussed with regard to adaptive theories of memory.

Exploring the Pareto frontier using multisexual evolutionary algorithms: an application to a flexible manufacturing problem

NASA Astrophysics Data System (ADS)

Bonissone, Stefano R.; Subbu, Raj

2002-12-01

In multi-objective optimization (MOO) problems we need to optimize many possibly conflicting objectives. For instance, in manufacturing planning we might want to minimize the cost and production time while maximizing the product's quality. We propose the use of evolutionary algorithms (EAs) to solve these problems. Solutions are represented as individuals in a population and are assigned scores according to a fitness function that determines their relative quality. Strong solutions are selected for reproduction, and pass their genetic material to the next generation. Weak solutions are removed from the population. The fitness function evaluates each solution and returns a related score. In MOO problems, this fitness function is vector-valued, i.e. it returns a value for each objective. Therefore, instead of a global optimum, we try to find the Pareto-optimal or non-dominated frontier. We use multi-sexual EAs with as many genders as optimization criteria. We have created new crossover and gender assignment functions, and experimented with various parameters to determine the best setting (yielding the highest number of non-dominated solutions.) These experiments are conducted using a variety of fitness functions, and the algorithms are later evaluated on a flexible manufacturing problem with total cost and time minimization objectives.

Coated woven materials and method of preparation

DOEpatents

McCreary, William J.; Carroll, David W.

1981-01-01

Coating of woven materials so that not only the outer surfaces are coated has been a problem. Now, a solution to that problem is the following: Woven materials are coated with materials, for example with metals or with pyrolytic carbon, which materials are deposited in Chemical Vapor Deposition (CVD) reactions using a fluidized bed so that the porosity of the woven material is retained and so that the tiny filaments which make up the strands which are woven (including inner as well as outer filaments) are substantially uniformly coated.

Pseudomonas aeruginosa biofilm growth inhibition on medical plastic materials by immobilized esterases and acylase.

PubMed

Kisch, Johannes Martin; Utpatel, Christian; Hilterhaus, Lutz; Streit, Wolfgang R; Liese, Andreas

2014-09-05

Biofilms are matrix-encapsulated cell aggregates that cause problems in technical and health-related areas; for example, 65 % of all human infections are biofilm associated. This is mainly due to their ameliorated resistance against antimicrobials and immune systems. Pseudomonas aeruginosa, a biofilm-forming organism, is commonly responsible for nosocomial infections. Biofilm development is partly mediated by signal molecules, such as acyl-homoserine lactones (AHLs) in Gram-negative bacteria. We applied horse liver esterase, porcine kidney acylase, and porcine liver esterase; these can hydrolyze AHLs, thereby inhibiting biofilm formation. As biofilm infections are often related to foreign material introduced into the human body, we immobilized the enzymes on medical plastic materials. Biofilm formation was quantified by Crystal Violet staining and confocal laser scanning microscopy, revealing up to 97 % (on silicone), 54 % (on polyvinyl chloride), and 77 % (on polyurethane) reduced biomass after 68 h growth. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Thin Film Mediated Phase Change Phenomena: Crystallization, Evaporation and Wetting

NASA Technical Reports Server (NTRS)

Wettlaufer, John S.

1998-01-01

We focus on two distinct materials science problems that arise in two distinct microgravity environments: In space and within the space of a polymeric network. In the former environment, we consider a near eutectic alloy film in contact with its vapor which, when evaporating on earth, will experience compositionally induced buoyancy driven convection. The latter will significantly influence the morphology of the crystallized end member. In the absence of gravity, the morphology will be dominated by molecular diffusion and Marangoni driven viscous flow, and we study these phenomena theoretically and experimentally. The second microgravity environment exists in liquids, gels, and other soft materials where the small mass of individual molecules makes the effect of gravity negligible next to the relatively strong forces of intermolecular collisions. In such materials, an essential question concerns how to relate the molecular dynamics to the bulk rheological behavior. Here, we observe experimentally the diffusive motion of a single molecule in a single polymer filament, embedded within a polymer network and find anomalous diffusive behavior.

Recalling Prerequisite Material in a Calculus II Course to Improve Student Success

ERIC Educational Resources Information Center

Mokry, Jeanette

2016-01-01

This article discusses preparation assignments used in a Calculus II course that cover material from prerequisite courses. Prior to learning new material, students work on problems outside of class involving concepts from algebra, trigonometry, and Calculus I. These problems are directly built upon in order to answer Calculus II questions,…

English Skills for Life Sciences: Problem Solving in Biology. Tutor Version [and] Student Version.

ERIC Educational Resources Information Center

California Univ., Los Angeles. Center for Language Education and Research.

This manual is part of a series of materials designed to reinforce essential concepts in physical science through interactive, language-sensitive, problem-solving exercises emphasizing cooperative learning. The materials are intended for limited-English-proficient (LEP) students in beginning physical science classes. The materials are for teams of…

Perspectives for online analysis of raw material by pulsed neutron irradiation

NASA Astrophysics Data System (ADS)

Bach, Pierre; Le Tourneur, P.; Poumarede, B.

1997-02-01

On-line analysis by pulsed neutron irradiation is an example of an advanced technology application of nuclear techniques, concerning real problems in the cement, mineral and coal industries. The most significant of these nuclear techniques is their capability of continuous measurement without contact and without sampling, which can lead to improved control of processes and resultant large financial savings. Compared to Californium neutron sources, the use of electrical pulsed neutron generators allows to obtain a higher signal/noise ratio for a more sensitive measurement, and allows to overcome a number of safety problems concerning transportation, installation and maintenance. An experiment related to a possible new on-line raw material analyzer is described, using a pulsed neutron generator. The key factors contributing to an accurate measurement are related to a suitable generator, to a high count rate gamma ray spectroscopy electronics, and to computational tools. Calculation and results for the optimization of the neutron irradiation time diagram are reported. One of the operational characteristics of such an equipment is related to neutron flux available: it is possible to adjust it to the requested accuracy, i.e. for a high accuracy during a few hours/day and for a lower accuracy the rest of the time. This feature allows to operate the neutron tube during a longer time, and then to reduce the cost of analysis.

A feasibility study of using remotely sensed data for water resource models

NASA Technical Reports Server (NTRS)

Ruff, J. F.

1973-01-01

Remotely sensed data were collected to demonstrate the feasibility of applying the results to water resource problems. Photographs of the Wolf Creek watershed in southwestern Colorado were collected over a one year period. Cloud top temperatures were measured using a radiometer. Thermal imagery of the Wolf Creek Pass area was obtained during one pre-dawn flight. Remote sensing studies of water resource problems for user agencies were also conducted. The results indicated that: (1) remote sensing techniques could be used to assist in the solution of water resource problems; (2) photogrammetric determination of snow depths is feasible; (3) changes in turbidity or suspended material concentration can be observed; and (4) surface turbulence can be related to bed scour; and (5) thermal effluents into rivers can be monitored.

Real-time OHT Dispatching Mechanism for the Interbay Automated Material Handling System with Shortcuts and Bypasses

NASA Astrophysics Data System (ADS)

Pan, Cong; Zhang, Jie; Qin, Wei

2017-05-01

As a key to improve the performance of the interbay automated material handling system (AMHS) in 300 mm semiconductor wafer fabrication system, the real-time overhead hoist transport (OHT) dispatching problem has received much attention. This problem is first formulated as a special form of assignment problem and it is proved that more than one solution will be obtained by Hungarian algorithm simultaneously. Through proposing and strictly proving two propositions related to the characteristics of these solutions, a modified Hungarian algorithm is designed to distinguish these solutions. Finally, a new real-time OHT dispatching method is carefully designed by implementing the solution obtained by the modified Hungarian algorithm. The experimental results of discrete event simulations show that, compared with conventional Hungarian algorithm dispatching method, the proposed dispatching method that chooses the solution with the maximum variance respectively reduces on average 4 s of the average waiting time and average lead time of wafer lots, and its performance is rather stable in multiple different scenarios of the interbay AMHS with different quantities of shortcuts. This research provides an efficient real-time OHT dispatching mechanism for the interbay AMHS with shortcuts and bypasses.

Compromise solution in the problem of change state control for the material body exposed to the external medium

NASA Astrophysics Data System (ADS)

Malafeyev, O. A.; Redinskikh, N. D.

2018-05-01

The problem of finding optimal temperature control of the material body state under the unknown in advance parameters of the external medium is formalized and studied in this paper. The problems of this type arise frequently in the real life. An optimal thermal regime is necessary to apply at the soil thawing or freezing, drying the building materials, heating the concrete to obtain the required strength, and so on. Problems of such type one can analyze making use the apparatus and methods of game theory. For describing the influence of external medium on the characteristics of different materials we make use the many-step two person zero-sum game in this paper. The compromise solution is taken as the optimality principle. The numerical example is given.

Outreach pharmacy service in old age homes: a Hong Kong experience.

PubMed

Lau, Wai-Man; Chan, Kit; Yung, Tsz-Ho; Lee, Anna See-Wing

2003-06-01

To explore drug-related problems in old age homes in Hong Kong through outreach pharmacy service. A standard form was used by outreach pharmacists to identify drug-related problems at old age homes. Homes were selected through random sampling, voluntary participation or adverse selection. Initial observation and assessment were performed in the first and second weeks. Appropriate advice and recommendations were given upon assessment and supplemented by a written report. Educational talks were provided to staff of the homes in addition to other drug information materials. At week 7 to 9, evaluations were carried out. Eighty-five homes were assessed and identified to have problems in the drug management system. These problems could generally be classified into physical storage (8.8%), quality of storage (19.2%), drug administration system (13.3%), documentation (16.4%), and drug knowledge of staff of homes (42.2%). Quality of drug storage was the most common problem found, followed by documentation and drug knowledge (73%, 50% and 44% of points assessed with problems, respectively). Apart from lack of drug knowledge and unawareness of potential risks by staff, minimal professional standards unmet may be fundamentally related to lack of professional input and inadequacy in legislation. Most homes demonstrated significant improvements upon simple interventions, from a majority of homes with more than 10 problems to a majority with less than 5 problems. Diverse problems in drug management are common in old age homes, which warrants attention and professional inputs. Simple interventions and education by pharmacists are shown to be effective in improving the quality of drug management and hence care to residents. While future financing of old age home service can be reviewed within the social context to provide incentives for improvement, review of regulatory policy with enforcement may be more fundamental and effective in upholding the service standard.

Applying Cases to Solve Ethical Problems: The Significance of Positive and Process-Oriented Reflection

PubMed Central

Antes, Alison L.; Thiel, Chase E.; Martin, Laura E.; Stenmark, Cheryl K.; Connelly, Shane; Devenport, Lynn D.; Mumford, Michael D.

2015-01-01

This study examined the role of reflection on personal cases for making ethical decisions with regard to new ethical problems. Participants assumed the position of a business manager in a hypothetical organization and solved ethical problems that might be encountered. Prior to making a decision for the business problems, participants reflected on a relevant ethical experience. The findings revealed that application of material garnered from reflection on a personal experience was associated with decisions of higher ethicality. However, whether the case was viewed as positive or negative, and whether the outcomes, process, or outcomes and processes embedded in the experience were examined, influenced the application of case material to the new problem. As expected, examining positive experiences and the processes involved in those positive experiences resulted in greater application of case material to new problems. Future directions and implications for understanding ethical decision-making are discussed. PMID:26257506

Health benefits of geologic materials and geologic processes

USGS Publications Warehouse

Finkelman, R.B.

2006-01-01

The reemerging field of Medical Geology is concerned with the impacts of geologic materials and geologic processes on animal and human health. Most medical geology research has been focused on health problems caused by excess or deficiency of trace elements, exposure to ambient dust, and on other geologically related health problems or health problems for which geoscience tools, techniques, or databases could be applied. Little, if any, attention has been focused on the beneficial health effects of rocks, minerals, and geologic processes. These beneficial effects may have been recognized as long as two million years ago and include emotional, mental, and physical health benefits. Some of the earliest known medicines were derived from rocks and minerals. For thousands of years various clays have been used as an antidote for poisons. "Terra sigillata," still in use today, may have been the first patented medicine. Many trace elements, rocks, and minerals are used today in a wide variety of pharmaceuticals and health care products. There is also a segment of society that believes in the curative and preventative properties of crystals (talismans and amulets). Metals and trace elements are being used in some of today's most sophisticated medical applications. Other recent examples of beneficial effects of geologic materials and processes include epidemiological studies in Japan that have identified a wide range of health problems (such as muscle and joint pain, hemorrhoids, burns, gout, etc.) that may be treated by one or more of nine chemically distinct types of hot springs, and a study in China indicating that residential coal combustion may be mobilizing sufficient iodine to prevent iodine deficiency disease. ?? 2006 MDPI. All rights reserved.

[Epidemiological aspects relating to the determination of fosfomycin sensitivity: results of a study on 300 strains isolated in a hospital milieu in Turin].

PubMed

Vanini, G C; Moiraghi Ruggenini, A; Grassi, R; Maury, F; Giardini, F

1979-01-01

The AA. evaluated the sensitivity to Fosfomycin and to other commonly used antibiotics of 105 bacterial strains isolated from hospital environment and 195 from pathological materials. They also studied the problem of bacterial resistence to Fosfomycin considering the frequency of "inner colonies" and of bacterial cross-resistance to other antibiotics.

Phase Relations in Ternary Systems in the Subsolidus Region: Methods to Formulate Solid Solution Equations and to Find Particular Compositions

ERIC Educational Resources Information Center

Alvarez-Montan~o, Victor E.; Farías, Mario H.; Brown, Francisco; Mun~oz-Palma, Iliana C.; Cubillas, Fernando; Castillon-Barraza, Felipe F.

2017-01-01

A good understanding of ternary phase diagrams is required to advance and/or to reproduce experimental research in solid-state and materials chemistry. The aim of this paper is to describe the solutions to problems that appear when studying or determining ternary phase diagrams. A brief description of the principal features shown in phase diagrams…

Vacuum pumps and systems: A review of current practice

NASA Technical Reports Server (NTRS)

Giles, Stuart

1986-01-01

A review of the fundamental characteristics of the many types of vacuum pumps and vacuum pumping systems is given. The optimum pumping range, relative cost, performance limitations, maintenance problems, system operating costs and similar subjects are discussed. Experiences from the thin film deposition, chemical processing, material handling, food processing and other industries, as well as space simulation are used to support conclusions and recommendations.

Resources for Adapting Low Vision Training Materials for the Adult with Low Literacy Skills. Practice Report

ERIC Educational Resources Information Center

Tucker, Laurel A.

2004-01-01

Adults with low vision who seek clinical low vision services need to be able to read (that is, to interpret or understand words, numbers, and symbols in print meaningfully). Reading difficulties that adults encounter during low vision therapy may be directly connected to a visual impairment or may be related to other reading problems, such as…

A class of fractional differential hemivariational inequalities with application to contact problem

NASA Astrophysics Data System (ADS)

Zeng, Shengda; Liu, Zhenhai; Migorski, Stanislaw

2018-04-01

In this paper, we study a class of generalized differential hemivariational inequalities of parabolic type involving the time fractional order derivative operator in Banach spaces. We use the Rothe method combined with surjectivity of multivalued pseudomonotone operators and properties of the Clarke generalized gradient to establish existence of solution to the abstract inequality. As an illustrative application, a frictional quasistatic contact problem for viscoelastic materials with adhesion is investigated, in which the friction and contact conditions are described by the Clarke generalized gradient of nonconvex and nonsmooth functionals, and the constitutive relation is modeled by the fractional Kelvin-Voigt law.

The piecewise parabolic method for Riemann problems in nonlinear elasticity.

PubMed

Zhang, Wei; Wang, Tao; Bai, Jing-Song; Li, Ping; Wan, Zhen-Hua; Sun, De-Jun

2017-10-18

We present the application of Harten-Lax-van Leer (HLL)-type solvers on Riemann problems in nonlinear elasticity which undergoes high-load conditions. In particular, the HLLD ("D" denotes Discontinuities) Riemann solver is proved to have better robustness and efficiency for resolving complex nonlinear wave structures compared with the HLL and HLLC ("C" denotes Contact) solvers, especially in the shock-tube problem including more than five waves. Also, Godunov finite volume scheme is extended to higher order of accuracy by means of piecewise parabolic method (PPM), which could be used with HLL-type solvers and employed to construct the fluxes. Moreover, in the case of multi material components, level set algorithm is applied to track the interface between different materials, while the interaction of interfaces is realized through HLLD Riemann solver combined with modified ghost method. As seen from the results of both the solid/solid "stick" problem with the same material at the two sides of contact interface and the solid/solid "slip" problem with different materials at the two sides, this scheme composed of HLLD solver, PPM and level set algorithm can capture the material interface effectively and suppress spurious oscillations therein significantly.

Environmental implications of plastic debris in marine settings—entanglement, ingestion, smothering, hangers-on, hitch-hiking and alien invasions

PubMed Central

Gregory, Murray R.

2009-01-01

Over the past five or six decades, contamination and pollution of the world’s enclosed seas, coastal waters and the wider open oceans by plastics and other synthetic, non-biodegradable materials (generally known as ‘marine debris’) has been an ever-increasing phenomenon. The sources of these polluting materials are both land- and marine-based, their origins may be local or distant, and the environmental consequences are many and varied. The more widely recognized problems are typically associated with entanglement, ingestion, suffocation and general debilitation, and are often related to stranding events and public perception. Among the less frequently recognized and recorded problems are global hazards to shipping, fisheries and other maritime activities. Today, there are rapidly developing research interests in the biota attracted to freely floating (i.e. pelagic) marine debris, commonly known as ‘hangers-on and hitch-hikers’ as well as material sinking to the sea floor despite being buoyant. Dispersal of aggressive alien and invasive species by these mechanisms leads one to reflect on the possibilities that ensuing invasions could endanger sensitive, or at-risk coastal environments (both marine and terrestrial) far from their native habitats. PMID:19528053

The validation of a generalized Hooke's law for coronary arteries.

PubMed

Wang, Chong; Zhang, Wei; Kassab, Ghassan S

2008-01-01

The exponential form of constitutive model is widely used in biomechanical studies of blood vessels. There are two main issues, however, with this model: 1) the curve fits of experimental data are not always satisfactory, and 2) the material parameters may be oversensitive. A new type of strain measure in a generalized Hooke's law for blood vessels was recently proposed by our group to address these issues. The new model has one nonlinear parameter and six linear parameters. In this study, the stress-strain equation is validated by fitting the model to experimental data of porcine coronary arteries. Material constants of left anterior descending artery and right coronary artery for the Hooke's law were computed with a separable nonlinear least-squares method with an excellent goodness of fit. A parameter sensitivity analysis shows that the stability of material constants is improved compared with the exponential model and a biphasic model. A boundary value problem was solved to demonstrate that the model prediction can match the measured arterial deformation under experimental loading conditions. The validated constitutive relation will serve as a basis for the solution of various boundary value problems of cardiovascular biomechanics.

Environmental implications of plastic debris in marine settings--entanglement, ingestion, smothering, hangers-on, hitch-hiking and alien invasions.

PubMed

Gregory, Murray R

2009-07-27

Over the past five or six decades, contamination and pollution of the world's enclosed seas, coastal waters and the wider open oceans by plastics and other synthetic, non-biodegradable materials (generally known as 'marine debris') has been an ever-increasing phenomenon. The sources of these polluting materials are both land- and marine-based, their origins may be local or distant, and the environmental consequences are many and varied. The more widely recognized problems are typically associated with entanglement, ingestion, suffocation and general debilitation, and are often related to stranding events and public perception. Among the less frequently recognized and recorded problems are global hazards to shipping, fisheries and other maritime activities. Today, there are rapidly developing research interests in the biota attracted to freely floating (i.e. pelagic) marine debris, commonly known as 'hangers-on and hitch-hikers' as well as material sinking to the sea floor despite being buoyant. Dispersal of aggressive alien and invasive species by these mechanisms leads one to reflect on the possibilities that ensuing invasions could endanger sensitive, or at-risk coastal environments (both marine and terrestrial) far from their native habitats.

Reason behind wet pack after steam sterilization and its consequences: An overview from Central Sterile Supply Department of a cancer center in eastern India.

PubMed

Basu, Debabrata

Wet pack after steam sterilization process that means there are surely obtain millions of microorganisms that can breed and multiply rapidly and objects are unsterile and can never be used for further procedure. There are many reasons behind the wet pack occurrences after autoclaving like poor quality of wrapping materials, faulty valves of rigid container, faulty loading and packaging technique, poor steam quality, sterilizer malfunction and may be design related problems in CSSD sterile storage area. Cause of wet pack after steam sterilization processes may occur severe problems because of wasted time and effort, increased work load, increased cost, potentially contaminated instruments, infection risk to the patient, poor patient outcomes and delayed or cancellation of procedures. But such wet pack scenario can be avoided by various methods by using good steam (water) quality, performing periodic maintenance of the Autoclaves, avoidance of sterilizer overloading, allowing adequate post sterilization time to cool down the materials to room temperature, using good quality wrapping materials, properly maintain temperature and humidity of sterile storage area etc. Copyright © 2016 King Saud Bin Abdulaziz University for Health Sciences. Published by Elsevier Ltd. All rights reserved.

Occupational exposures associated with work-related asthma and work-related wheezing among U.S. workers.

PubMed

Arif, Ahmed A; Delclos, George L; Whitehead, Lawrence W; Tortolero, Susan R; Lee, Eun S

2003-10-01

National estimates of occupational asthma (OA) in the United States are sparse. Using data from the Third National Health and Nutrition Examination Survey (NHANES III) 1988-1994, we analyzed associations between occupation and work-related asthma and work-related wheezing among U.S. workers. This study identified several occupations that were at risk of developing work-related asthma and/or wheezing, with cleaners and equipment cleaners showing the highest risks. Other major occupations identified were farm and agriculture; entertainment; protective services; construction; mechanics and repairers; textile; fabricators and assemblers; other transportation and material moving occupations; freight, stock, and material movers; and motor vehicle operators. The population attributable risks for work-related asthma and work-related wheezing were 26% and 27%, respectively. This study adds evidence to the literature that identifies work-related asthma as an important public health problem. Several occupations are targeted for additional evaluation and study. Of particular interest are cleaners, which are being increasingly reported as a risk group for asthma. Future intervention strategies need to be developed for effective control and prevention of asthma in the workplace. Copyright 2003 Wiley-Liss, Inc.

ADHD Symptoms in Pathological and Problem Gamblers in Singapore.

PubMed

Mak, Charles; Tan, Kok Kah; Guo, Song

2018-06-22

Background : There is relatively little research examining the relationship between Attention-Deficit/Hyperactivity Disorder (ADHD) and gambling addiction. This study seeks to explore for ADHD symptoms in adult gambling addiction patients and to evaluate their gambling-related cognitions. Materials and Methods : A cross-sectional survey was conducted at National Addictions Management Service, Institute of Mental Health, in Singapore. Patients presenting for gambling treatment were screened for ADHD symptoms and assessed for severity of gambling-related cognitions. The primary objective was to observe the rate of patients screening positive for ADHD. Results : 20% of the sample screened positive for ADHD. These individuals also had lower levels of gambling-related cognitions. No significant correlation was noted between ADHD symptoms and gambling-related cognition scores. Conclusions : Positive screening results for ADHD occurred frequently in our sample of Pathological Gambling (PG) and Problem Gambling patients and these affected individuals also exhibited lower levels of gambling-related cognitions. This finding may suggest that the gambling behavior in patients with ADHD-PG comorbidity is driven by impulsivity rather than gambling-related cognitions, which has implication on treatment considerations. Further research with a larger sample size is indicated.

A direct vulnerable atherosclerotic plaque elasticity reconstruction method based on an original material-finite element formulation: theoretical framework

PubMed Central

Bouvier, Adeline; Deleaval, Flavien; Doyley, Marvin M; Yazdani, Saami K; Finet, Gérard; Le Floc'h, Simon; Cloutier, Guy; Pettigrew, Roderic I; Ohayon, Jacques

2016-01-01

The peak cap stress (PCS) amplitude is recognized as a biomechanical predictor of vulnerable plaque (VP) rupture. However, quantifying PCS in vivo remains a challenge since the stress depends on the plaque mechanical properties. In response, an iterative material finite element (FE) elasticity reconstruction method using strain measurements has been implemented for the solution of these inverse problems. Although this approach could resolve the mechanical characterization of VPs, it suffers from major limitations since (i) it is not adapted to characterize VPs exhibiting high material discontinuities between inclusions, and (ii) does not permit real time elasticity reconstruction for clinical use. The present theoretical study was therefore designed to develop a direct material-FE algorithm for elasticity reconstruction problems which accounts for material heterogeneities. We originally modified and adapted the extended FE method (Xfem), used mainly in crack analysis, to model material heterogeneities. This new algorithm was successfully applied to six coronary lesions of patients imaged in vivo with intravascular ultrasound. The results demonstrated that the mean relative absolute errors of the reconstructed Young's moduli obtained for the arterial wall, fibrosis, necrotic core, and calcified regions of the VPs decreased from 95.3±15.56%, 98.85±72.42%, 103.29±111.86% and 95.3±10.49%, respectively, to values smaller than 2.6 × 10−8±5.7 × 10−8% (i.e. close to the exact solutions) when including modified-Xfem method into our direct elasticity reconstruction method. PMID:24240392

Evolution of plastic anisotropy for high-strain-rate computations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schiferl, S.K.; Maudlin, P.J.

1994-12-01

A model for anisotropic material strength, and for changes in the anisotropy due to plastic strain, is described. This model has been developed for use in high-rate, explicit, Lagrangian multidimensional continuum-mechanics codes. The model handles anisotropies in single-phase materials, in particular the anisotropies due to crystallographic texture--preferred orientations of the single-crystal grains. Textural anisotropies, and the changes in these anisotropies, depend overwhelmingly no the crystal structure of the material and on the deformation history. The changes, particularly for a complex deformations, are not amenable to simple analytical forms. To handle this problem, the material model described here includes a texturemore » code, or micromechanical calculation, coupled to a continuum code. The texture code updates grain orientations as a function of tensor plastic strain, and calculates the yield strength in different directions. A yield function is fitted to these yield points. For each computational cell in the continuum simulation, the texture code tracks a particular set of grain orientations. The orientations will change due to the tensor strain history, and the yield function will change accordingly. Hence, the continuum code supplies a tensor strain to the texture code, and the texture code supplies an updated yield function to the continuum code. Since significant texture changes require relatively large strains--typically, a few percent or more--the texture code is not called very often, and the increase in computer time is not excessive. The model was implemented, using a finite-element continuum code and a texture code specialized for hexagonal-close-packed crystal structures. The results for several uniaxial stress problems and an explosive-forming problem are shown.« less

Failure processes in soft and quasi-brittle materials with nonhomogeneous microstructures

NASA Astrophysics Data System (ADS)

Spring, Daniel W.

Material failure pervades the fields of materials science and engineering; it occurs at various scales and in various contexts. Understanding the mechanisms by which a material fails can lead to advancements in the way we design and build the world around us. For example, in structural engineering, understanding the fracture of concrete and steel can lead to improved structural systems and safer designs; in geological engineering, understanding the fracture of rock can lead to increased efficiency in oil and gas extraction; and in biological engineering, understanding the fracture of bone can lead to improvements in the design of bio-composites and medical implants. In this thesis, we numerically investigate a wide spectrum of failure behavior; in soft and quasi-brittle materials with nonhomogeneous microstructures considering a statistical distribution of material properties. The first topic we investigate considers the influence of interfacial interactions on the macroscopic constitutive response of particle reinforced elastomers. When a particle is embedded into an elastomer, the polymer chains in the elastomer tend to adsorb (or anchor) onto the surface of the particle; creating a region in the vicinity of each particle (often referred to as an interphase) with distinct properties from those in the bulk elastomer. This interphasial region has been known to exist for many decades, but is primarily omitted in computational investigations of such composites. In this thesis, we present an investigation into the influence of interphases on the macroscopic constitutive response of particle filled elastomers undergoing large deformations. In addition, at large deformations, a localized region of failure tends to accumulate around inclusions. To capture this localized region of failure (often referred to as interfacial debonding), we use cohesive zone elements which follow the Park-Paulino-Roesler traction-separation relation. To account for friction, we present a new, coupled cohesive-friction relation and detail its formulation and implementation. In the process of this investigation, we developed a small library of cohesive elements for use with a commercially available finite element analysis software package. Additionally, in this thesis, we present a series of methods for reducing mesh dependency in two-dimensional dynamic cohesive fracture simulations of quasi-brittle materials. In this setting, cracks are only permitted to propagate along element facets, thus a poorly designed discretization of the problem domain can introduce artifacts into the fracture behavior. To reduce mesh induced artifacts, we consider unstructured polygonal finite elements. A randomly-seeded polygonal mesh leads to an isotropic discretization of the problem domain, which does not bias the direction of crack propagation. However, polygonal meshes tend to limit the possible directions a crack may travel at each node, making this discretization a poor candidate for dynamic cohesive fracture simulations. To alleviate this problem, we propose two new topological operators. The first operator we propose is adaptive element-splitting, and the second is adaptive mesh refinement. Both operators are designed to improve the ability of unstructured polygonal meshes to capture crack patterns in dynamic cohesive fracture simulations. However, we demonstrate that element-splitting is more suited to pervasive fracture problems, whereas, adaptive refinement is more suited to problems exhibiting a dominant crack. Finally, we investigate the use of geometric and constitutive design features to regularize pervasive fragmentation behavior in three-dimensions. Throughout pervasive fracture simulations, many cracks initiate, propagate, branch and coalesce simultaneously. Because of the cohesive element method's unique framework, this behavior can be captured in a regularized manner. In this investigation, unstructuring techniques are used to introduce randomness into a numerical model. The behavior of quasi-brittle materials undergoing pervasive fracture and fragmentation is then examined using three examples. The examples are selected to investigate some of the significant factors influencing pervasive fracture and fragmentation behavior; including, geometric features, loading conditions, and material gradation.

Problem Solving-based Learning Materials on Fraction for Training Creativity of Elementary School Students

NASA Astrophysics Data System (ADS)

Widhitama, Y. N.; Lukito, A.; Khabibah, S.

2018-01-01

The aim of this research is to develop problem solving based learning materials on fraction for training creativity of elementary school students. Curriculum 2006 states that mathematics should be studied by all learners starting from elementary level in order for them mastering thinking skills, one of them is creative thinking. To our current knowledge, there is no such a research topic being done. To promote this direction, we initiate by developing learning materials with problem solving approach. The developed materials include Lesson Plan, Student Activity Sheet, Mathematical Creativity Test, and Achievement Test. We implemented a slightly modified 4-D model by Thiagajan et al. (1974) consisting of Define, Design, Development, and Disseminate. Techniques of gathering data include observation, test, and questionnaire. We applied three good qualities for the resulted materials; that is, validity, practicality, and effectiveness. The results show that the four mentioned materials meet the corresponding criteria of good quality product.

Improving Geoscience Students' Spatial Thinking Skills: Applying Cognitive Science Research in the Classroom

NASA Astrophysics Data System (ADS)

Ormand, C. J.; Shipley, T. F.; Manduca, C. A.; Tikoff, B.

2011-12-01

Spatial thinking skills are critical to success in many subdisciplines of the geosciences (and beyond). There are many components of spatial thinking, such as mental rotation, penetrative visualization, disembedding, perspective taking, and navigation. Undergraduate students in introductory and upper-level geoscience courses bring a wide variety of spatial skill levels to the classroom, as measured by psychometric tests of many of these components of spatial thinking. Furthermore, it is not unusual for individual students to excel in some of these areas while struggling in others. Although pre- and post-test comparisons show that student skill levels typically improve over the course of an academic term, average gains are quite modest. This suggests that it may be valuable to develop interventions to help undergraduate students develop a range of spatial skills that can be used to solve geoscience problems. Cognitive science research suggests a number of strong strategies for building students' spatial skills. Practice is essential, and time on task is correlated to improvement. Progressive alignment may be used to scaffold students' successes on simpler problems, allowing them to see how more complex problems are related to those they can solve. Gesturing has proven effective in moving younger students from incorrect problem-solving strategies to correct strategies in other disciplines. These principles can be used to design instructional materials to improve undergraduate geoscience students' spatial skills; we will present some examples of such materials.

Cohesive phase-field fracture and a PDE constrained optimization approach to fracture inverse problems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tupek, Michael R.

2016-06-30

In recent years there has been a proliferation of modeling techniques for forward predictions of crack propagation in brittle materials, including: phase-field/gradient damage models, peridynamics, cohesive-zone models, and G/XFEM enrichment techniques. However, progress on the corresponding inverse problems has been relatively lacking. Taking advantage of key features of existing modeling approaches, we propose a parabolic regularization of Barenblatt cohesive models which borrows extensively from previous phase-field and gradient damage formulations. An efficient explicit time integration strategy for this type of nonlocal fracture model is then proposed and justified. In addition, we present a C++ computational framework for computing in- putmore » parameter sensitivities efficiently for explicit dynamic problems using the adjoint method. This capability allows for solving inverse problems involving crack propagation to answer interesting engineering questions such as: 1) what is the optimal design topology and material placement for a heterogeneous structure to maximize fracture resistance, 2) what loads must have been applied to a structure for it to have failed in an observed way, 3) what are the existing cracks in a structure given various experimental observations, etc. In this work, we focus on the first of these engineering questions and demonstrate a capability to automatically and efficiently compute optimal designs intended to minimize crack propagation in structures.« less

Electronic waste management approaches: An overview

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kiddee, Peeranart; Cooperative Research Centre for Contamination Assessment and Remediation of the Environment, Mawson Lakes Campus, Adelaide, SA 5095; Naidu, Ravi, E-mail: ravi.naidu@crccare.com

2013-05-15

Highlights: ► Human toxicity of hazardous substances in e-waste. ► Environmental impacts of e-waste from disposal processes. ► Life Cycle Assessment (LCA), Material Flow Analysis (MFA), Multi Criteria Analysis (MCA) and Extended Producer Responsibility (EPR) to and solve e-waste problems. ► Key issues relating to tools managing e-waste for sustainable e-waste management. - Abstract: Electronic waste (e-waste) is one of the fastest-growing pollution problems worldwide given the presence if a variety of toxic substances which can contaminate the environment and threaten human health, if disposal protocols are not meticulously managed. This paper presents an overview of toxic substances present inmore » e-waste, their potential environmental and human health impacts together with management strategies currently being used in certain countries. Several tools including Life Cycle Assessment (LCA), Material Flow Analysis (MFA), Multi Criteria Analysis (MCA) and Extended Producer Responsibility (EPR) have been developed to manage e-wastes especially in developed countries. The key to success in terms of e-waste management is to develop eco-design devices, properly collect e-waste, recover and recycle material by safe methods, dispose of e-waste by suitable techniques, forbid the transfer of used electronic devices to developing countries, and raise awareness of the impact of e-waste. No single tool is adequate but together they can complement each other to solve this issue. A national scheme such as EPR is a good policy in solving the growing e-waste problems.« less

Compendium of methods for applying measured data to vibration and acoustic problems

NASA Astrophysics Data System (ADS)

Dejong, R. G.

1985-10-01

The scope of this report includes the measurement, analysis and use of vibration and acoustic data. The purpose of this report is then two-fold. First, it provides introductory material in an easily understood manner to engineers, technicians, and their managers in areas other than their specialties relating to the measurement, analysis and use of vibration and acoustic data. Second, it provides a quick reference source for engineers, technicians and their managers in the areas of their specialties relating to the measurement, analysis and use of vibration and acoustic data.

High intensity 5 eV O-atom exposure facility for material degradation studies

NASA Technical Reports Server (NTRS)

Cross, J. B.; Spangler, L. H.; Hoffbauer, M. A.; Archuleta, F. A.; Leger, Lubert; Visentine, James; Hunton, Don E.; Cross, J. B.

1986-01-01

An atomic oxygen exposure facility was developed for studies of material degradation. The goal of these studies is to provide design criteria and information for the manufacture of long life (20 to 30 years) construction materials for use in low Earth orbit. The studies that are being undertaken will provide: (1) absolute reaction cross sections for the engineering design problems, (2) formulations of reaction mechanisms for use in the selection of suitable existing materials and the design of new more resistant ones, and (3) the calibration of flight hardware (mass spectrometers, etc.) in order to directly relate experiments performed in low Earth orbit to ground based investigations. The facility consists of a CW laser sustained discharge source of O-atoms, an atomic beam formation and diagnostics system, a spinning rotor viscometer, and provision for using the system for calibration of actual flight instruments.

Strategies to curb structural changes of lithium/transition metal oxide cathode materials & the changes’ effects on thermal & cycling stability

NASA Astrophysics Data System (ADS)

Xiqian, Yu; Enyuan, Hu; Seongmin, Bak; Yong-Ning, Zhou; Xiao-Qing, Yang

2016-01-01

Structural transformation behaviors of several typical oxide cathode materials during a heating process are reviewed in detail to provide in-depth understanding of the key factors governing the thermal stability of these materials. We also discuss applying the information about heat induced structural evolution in the study of electrochemically induced structural changes. All these discussions are expected to provide valuable insights for designing oxide cathode materials with significantly improved structural stability for safe, long-life lithium ion batteries, as the safety of lithium-ion batteries is a critical issue; it is widely accepted that the thermal instability of the cathodes is one of the most critical factors in thermal runaway and related safety problems. Project supported by the U.S. Department of Energy, the Assistant Secretary for Energy Efficiency and Renewable Energy, Office of Vehicle Technologies (Grant No. DE-SC0012704).

Fundamentals of tribology at the atomic level

NASA Technical Reports Server (NTRS)

Ferrante, John; Pepper, Stephen V.

1989-01-01

Tribology, the science and engineering of solid surfaces in moving contact, is a field that encompasses many disciplines: solid state physics, chemistry, materials science, and mechanical engineering. In spite of the practical importance and maturity of the field, the fundamental understanding of basic phenomena has only recently been attacked. An attempt to define some of these problems and indicate some profitable directions for future research is presented. There are three broad classifications: (1) fluid properties (compression, rheology, additives and particulates); (2) material properties of the solids (deformation, defect formation and energy loss mechanisms); and (3) interfacial properties (adhesion, friction chemical reactions, and boundary films). Research in the categories has traditionally been approached by considering macroscopic material properties. Recent activity has shown that some issues can be approached at the atomic level: the atoms in the materials can be manipulated both experimentally and theoretically, and can produce results related to macroscopic phenomena.

Bed-material entrainment and associated transportation infrastructure problems in streams of the Edwards Plateau, central Texas

USGS Publications Warehouse

Heitmuller, Franklin T.; Asquith, William H.

2008-01-01

The Texas Department of Transportation commonly builds and maintains low-water crossings (LWCs) over streams in the Edwards Plateau in Central Texas. LWCs are low-height structures, typically constructed of concrete and asphalt, that provide acceptable passage over seasonal rivers or streams with relatively low normal-depth flow. They are designed to accommodate flow by roadway overtopping during high-flow events. The streams of the Edwards Plateau are characterized by cobble- and gravel-sized bed material and highly variable flow regimes. Low base flows that occur most of the time occasionally are interrupted by severe floods. The floods entrain and transport substantial loads of bed material in the stream channels. As a result, LWCs over streams in the Edwards Plateau are bombarded and abraded by bed material during floods and periodically must be maintained or even replaced.

Source Materials and the Library: The Dispersion of the Beaumont Papers

PubMed Central

Pizer, Irwin H.

1964-01-01

The author discusses the confusion, attributable to misleading references, which long obscured the location of the main portion of the William Beaumont papers. The collection was previously thought to be in the National Library of Medicine, but it is actually housed in the Washington University School of Medicine Library. This has been clarified by the discovery of a series of previously unpublished letters of Sir William Osler, as well as by other newly found materials. The history of the Washington University School of Medicine Library is reviewed, and the facts relating to the disposition of the Beaumont collection in that library rather than the National Library of Medicine are told. Also considered are some of the problems which the dispersion of documentary source materials creates for the scholar. With the Beaumont papers as a case in point, various locations of such materials are cited, and their contents briefly noted. PMID:14119306

Editorial, Forum and Book Review

NASA Astrophysics Data System (ADS)

Caulfield, H. J.

1981-04-01

In keeping with my desire to make editorial decisions openly and to seek reader response to those decisions, I want to announce a policy on the citation of military classified information in Optical Engineering. The problem, is a vexing one. If the purpose of a paper is to convey the maximum amount of information about a topic, should it trouble your editor that otherwise-useful references are inaccessible to some of the readers? Should he deliber-ately suppress the information that related material is available because some of the readers cannot use that material? Should the editor ban references to an obscure Dutch journal (for example) because some of the readers cannot use that material? Yet, there is something distasteful about citing classified material. Does it make Optical Engineering American and not international? Could it become a Department of Defense outlet for unclassified information? Would it be elitist?

On the problem of stress singularities in bonded orthotropic materials

NASA Technical Reports Server (NTRS)

Erdogan, F.; Delale, F.

1976-01-01

The problem of stress singularities at the leading edge of a crack lying in the neighborhood of a bimaterial interface in bonded orthotropic materials is considered. The main objective is to study the effect of material orthotropy on the singular behavior of the stress state when the crack touches or intersects the interface. The results indicate that, due to the large number of material constants involved, in orthotropic materials, the power of stress singularity as well as the stress intensity factor can be considerably different than that found in the isotropic materials with the same stiffness ratio perpendicular to the crack.

The crack problem in bonded nonhomogeneous materials

NASA Technical Reports Server (NTRS)

Erdogan, Fazil; Kaya, A. C.; Joseph, P. F.

1988-01-01

The plane elasticity problem for two bonded half planes containing a crack perpendicular to the interface was considered. The effect of very steep variations in the material properties near the diffusion plane on the singular behavior of the stresses and stress intensity factors were studied. The two materials were thus, assumed to have the shear moduli mu(o) and mu(o) exp (Beta x), x=0 being the diffusion plane. Of particular interest was the examination of the nature of stress singularity near a crack tip terminating at the interface where the shear modulus has a discontinuous derivative. The results show that, unlike the crack problem in piecewise homogeneous materials for which the singularity is of the form r/alpha, 0 less than alpha less than 1, in this problem the stresses have a standard square-root singularity regardless of the location of the crack tip. The nonhomogeneity constant Beta has, however, considerable influence on the stress intensity factors.

The crack problem in bonded nonhomogeneous materials

NASA Technical Reports Server (NTRS)

Erdogan, F.; Joseph, P. F.; Kaya, A. C.

1991-01-01

The plane elasticity problem for two bonded half planes containing a crack perpendicular to the interface was considered. The effect of very steep variations in the material properties near the diffusion plane on the singular behavior of the stresses and stress intensity factors were studied. The two materials were thus, assumed to have the shear moduli mu(o) and mu(o) exp (Beta x), x=0 being the diffusion plane. Of particular interest was the examination of the nature of stress singularity near a crack tip termination at the interface where the shear modulus has a discontinuous derivative. The results show that, unlike the crack problem in piecewise homogeneous materials for which the singularity is of the form r/alpha, 0 less than alpha less than 1, in this problem the stresses have a standard square-root singularity regardless of the location of the crack tip. The nonhomogeneity constant Beta has, however, considerable influence on the stress intensity factors.

Electrochemical and in vitro behavior of the nanosized composites of Ti-6Al-4V and TiO2 fabricated by friction stir process

NASA Astrophysics Data System (ADS)

Zhang, Chengjian; Ding, Zihao; Xie, Lechun; Zhang, Lai-Chang; Wu, Laizhi; Fu, Yuanfei; Wang, Liqiang; Lu, Weijie

2017-11-01

Although Ti-6Al-4V has been widely used in biomaterial field. Compared with other classes of materials, it still encounters some problems such as low surface hardness and relative low biocompatibility. To solve these problems friction stir processing (FSP) was applied to fabricate a nanosized composite layer of TiO2 and Ti-6Al-4V. Uniform distribution of TiO2 particles with some clusters on the surface of alloy can be observed. Due to severe plastic deformation and stirring heat, nanocrystallines and amorphous TiO2 can be observed in stir zone. FSPed samples show significant improvement in surface microhardness and biocompatibility due to its modified structure compared with original sample. In addition, through corrosion behaviors of the samples in simulated body fluid, it is found that FSP can enhance whilst TiO2 reduces the possibility and corrosion rate of material in environment of human body.

High-Fidelity Coupled Monte-Carlo/Thermal-Hydraulics Calculations

NASA Astrophysics Data System (ADS)

Ivanov, Aleksandar; Sanchez, Victor; Ivanov, Kostadin

2014-06-01

Monte Carlo methods have been used as reference reactor physics calculation tools worldwide. The advance in computer technology allows the calculation of detailed flux distributions in both space and energy. In most of the cases however, those calculations are done under the assumption of homogeneous material density and temperature distributions. The aim of this work is to develop a consistent methodology for providing realistic three-dimensional thermal-hydraulic distributions by coupling the in-house developed sub-channel code SUBCHANFLOW with the standard Monte-Carlo transport code MCNP. In addition to the innovative technique of on-the fly material definition, a flux-based weight-window technique has been introduced to improve both the magnitude and the distribution of the relative errors. Finally, a coupled code system for the simulation of steady-state reactor physics problems has been developed. Besides the problem of effective feedback data interchange between the codes, the treatment of temperature dependence of the continuous energy nuclear data has been investigated.

Metal-organic framework-based separator for lithium-sulfur batteries

NASA Astrophysics Data System (ADS)

Bai, Songyan; Liu, Xizheng; Zhu, Kai; Wu, Shichao; Zhou, Haoshen

2016-07-01

Lithium-sulfur batteries are a promising energy-storage technology due to their relatively low cost and high theoretical energy density. However, one of their major technical problems is the shuttling of soluble polysulfides between electrodes, resulting in rapid capacity fading. Here, we present a metal-organic framework (MOF)-based battery separator to mitigate the shuttling problem. We show that the MOF-based separator acts as an ionic sieve in lithium-sulfur batteries, which selectively sieves Li+ ions while efficiently suppressing undesired polysulfides migrating to the anode side. When a sulfur-containing mesoporous carbon material (approximately 70 wt% sulfur content) is used as a cathode composite without elaborate synthesis or surface modification, a lithium-sulfur battery with a MOF-based separator exhibits a low capacity decay rate (0.019% per cycle over 1,500 cycles). Moreover, there is almost no capacity fading after the initial 100 cycles. Our approach demonstrates the potential for MOF-based materials as separators for energy-storage applications.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wollaber, Allan Benton; Park, HyeongKae; Lowrie, Robert Byron

Recent efforts at Los Alamos National Laboratory to develop a moment-based, scale-bridging [or high-order (HO)–low-order (LO)] algorithm for solving large varieties of the transport (kinetic) systems have shown promising results. A part of our ongoing effort is incorporating this methodology into the framework of the Eulerian Applications Project to achieve algorithmic acceleration of radiationhydrodynamics simulations in production software. By starting from the thermal radiative transfer equations with a simple material-motion correction, we derive a discretely consistent energy balance equation (LO equation). We demonstrate that the corresponding LO system for the Monte Carlo HO solver is closely related to the originalmore » LO system without material-motion corrections. We test the implementation on a radiative shock problem and show consistency between the energy densities and temperatures in the HO and LO solutions as well as agreement with the semianalytic solution. We also test the approach on a more challenging two-dimensional problem and demonstrate accuracy enhancements and algorithmic speedups. This paper extends a recent conference paper by including multigroup effects.« less

Composite material impregnation unit

NASA Technical Reports Server (NTRS)

Wilkinson, S. P.; Marchello, J. M.; Johnston, N. J.

1993-01-01

This memorandum presents an introduction to the NASA multi-purpose prepregging unit which is now installed and fully operational at the Langley Research Center in the Polymeric Materials Branch. A description of the various impregnation methods that are available to the prepregger are presented. Machine operating details and protocol are provided for its various modes of operation. These include, where appropriate, the related equations for predicting the desired prepreg specifications. Also, as the prepregger is modular in its construction, each individual section is described and discussed. Safety concerns are an important factor and a chapter has been included that highlights the major safety features. Initial experiences and observations for fiber impregnation are described. These first observations have given great insight into the areas of future work that need to be addressed. Future memorandums will focus on these individual processes and their related problems.

The New Sourcebook for Teaching Reasoning and Problem Solving in Elementary School. A Longwood Professional Book.

ERIC Educational Resources Information Center

Krulik, Stephen; Rudnick, Jesse A.

Many teachers and administrators have recognized that problem solving and reasoning represent two of the primary goals in the education of children. In order for teachers to achieve these goals, they must have appropriate materials available to them. This book includes materials to help teach and assess problem solving and reasoning. The first six…

School Learning Materials on Water Problems of New Mexico and the Southwest.

ERIC Educational Resources Information Center

Buethe, Chris; And Others

Schools typically make no special efforts to prepare students to cope with present and anticipated water problems. Using this as a premise, the objective of this study was to prepare a set of mediated learning packages based upon water problems of New Mexico and the dry regions of the Southwest. These learning materials were prepared and field…

Comet composition and density analyzer

NASA Technical Reports Server (NTRS)

Clark, B. C.

1982-01-01

Distinctions between cometary material and other extraterrestrial materials (meteorite suites and stratospherically-captured cosmic dust) are addressed. The technique of X-ray fluorescence (XRF) for analysis of elemental composition is involved. Concomitant with these investigations, the problem of collecting representative samples of comet dust (for rendezvous missions) was solved, and several related techniques such as mineralogic analysis (X-ray diffraction), direct analysis of the nucleus without docking (electron macroprobe), dust flux rate measurement, and test sample preparation were evaluated. An explicit experiment concept based upon X-ray fluorescence analysis of biased and unbiased sample collections was scoped and proposed for a future rendezvous mission with a short-period comet.

Damage Tolerance Assessment Branch

NASA Technical Reports Server (NTRS)

Walker, James L.

2013-01-01

The Damage Tolerance Assessment Branch evaluates the ability of a structure to perform reliably throughout its service life in the presence of a defect, crack, or other form of damage. Such assessment is fundamental to the use of structural materials and requires an integral blend of materials engineering, fracture testing and analysis, and nondestructive evaluation. The vision of the Branch is to increase the safety of manned space flight by improving the fracture control and the associated nondestructive evaluation processes through development and application of standards, guidelines, advanced test and analytical methods. The Branch also strives to assist and solve non-aerospace related NDE and damage tolerance problems, providing consultation, prototyping and inspection services.

Assessing Mesoscale Material Response via High-Resolution Line-Imaging VISAR

NASA Astrophysics Data System (ADS)

Furnish, M. D.; Trott, W. M.; Mason, J.; Podsednik, J.; Reinhart, W. D.; Hall, C.

2004-07-01

Of special promise for providing dynamic mesoscale response data is the line-imaging VISAR, an instrument for providing spatially resolved velocity histories in dynamic experiments. We have prepared a line-imaging VISAR system capable of spatial resolution in the 10 - 20 micron range. We are applying this instrument to selected experiments on a compressed gas gun, chosen to provide initial data for several problems of interest, including: (1) pore-collapse in single-crystal copper (70 micron diameter hole; 2 different versions); and (2) response of a welded joint in dissimilar materials (Ta, Nb) to ramp loading relative to that of a compression joint.

The Pack Method for Compressive Tests of Thin Specimens of Materials Used in Thin-Wall Structures

NASA Technical Reports Server (NTRS)

Aitchison, C S; Tuckerman, L B

1939-01-01

The strength of modern lightweight thin-wall structures is generally limited by the strength of the compression members. An adequate design of these members requires a knowledge of the compressive stress-strain graph of the thin-wall material. The "pack" method was developed at the National Bureau of Standards with the support of the National Advisory Committee for Aeronautics to make possible a determination of compressive stress-strain graphs for such material. In the pack test an odd number of specimens are assembled into a relatively stable pack, like a "pack of cards." Additional lateral stability is obtained from lateral supports between the external sheet faces of the pack and outside reactions. The tests seems adequate for many problems in structural research.

Organic Electronics for Point-of-Care Metabolite Monitoring.

PubMed

Pappa, Anna-Maria; Parlak, Onur; Scheiblin, Gaetan; Mailley, Pascal; Salleo, Alberto; Owens, Roisin M

2018-01-01

In this review we focus on demonstrating how organic electronic materials can solve key problems in biosensing thanks to their unique material properties and implementation in innovative device configurations. We highlight specific examples where these materials solve multiple issues related to complex sensing environments, and we benchmark these examples by comparing them to state-of-the-art commercially available sensing using alternative technologies. We have categorized our examples by sample type, focusing on sensing from body fluids in vitro and on wearable sensors, which have attracted significant interest owing to their integration with everyday life activities. We finish by describing a future trend for in vivo, implantable sensors, which aims to build on current progress from sensing in biological fluids ex vivo. Copyright © 2017 Elsevier Ltd. All rights reserved.

Tailoring vibration mode shapes using topology optimization and functionally graded material concepts

NASA Astrophysics Data System (ADS)

Montealegre Rubio, Wilfredo; Paulino, Glaucio H.; Nelli Silva, Emilio Carlos

2011-02-01

Tailoring specified vibration modes is a requirement for designing piezoelectric devices aimed at dynamic-type applications. A technique for designing the shape of specified vibration modes is the topology optimization method (TOM) which finds an optimum material distribution inside a design domain to obtain a structure that vibrates according to specified eigenfrequencies and eigenmodes. Nevertheless, when the TOM is applied to dynamic problems, the well-known grayscale or intermediate material problem arises which can invalidate the post-processing of the optimal result. Thus, a more natural way for solving dynamic problems using TOM is to allow intermediate material values. This idea leads to the functionally graded material (FGM) concept. In fact, FGMs are materials whose properties and microstructure continuously change along a specific direction. Therefore, in this paper, an approach is presented for tailoring user-defined vibration modes, by applying the TOM and FGM concepts to design functionally graded piezoelectric transducers (FGPT) and non-piezoelectric structures (functionally graded structures—FGS) in order to achieve maximum and/or minimum vibration amplitudes at certain points of the structure, by simultaneously finding the topology and material gradation function. The optimization problem is solved by using sequential linear programming. Two-dimensional results are presented to illustrate the method.

Isometric deformations of unstretchable material surfaces, a spatial variational treatment

NASA Astrophysics Data System (ADS)

Chen, Yi-Chao; Fosdick, Roger; Fried, Eliot

2018-07-01

The stored energy of an unstretchable material surface is assumed to depend only upon the curvature tensor. By control of its edge(s), the surface is deformed isometrically from its planar undistorted reference configuration into an equilibrium shape. That shape is to be determined from a suitably constrained variational problem as a state of relative minimal potential energy. We pose the variational problem as one of relative minimum potential energy in a spatial form, wherein the deformation of a flat, undistorted region D in E2 to its distorted form S in E3 is assumed specified. We then apply the principle that the first variation of the potential energy, expressed as a functional over S ∪ ∂S , must vanish for all admissible variations that correspond to isometric deformations from the distorted configuration S and that also contain the essence of flatness that characterizes the reference configuration D , but is not covered by the single statement that the variation of S correspond to an isometric deformation. We emphasize the commonly overlooked condition that the spatial expression of the variational problem requires an additional variational constraint of zero Gaussian curvature to ensure that variations from S that are isometric deformations also contain the notion of flatness. In this context, it is particularly revealing to observe that the two constraints produce distinct, but essential and complementary, conditions on the first variation of S. The resulting first variation integral condition, together with the constraints, may be applied, for example, to the case of a flat, undistorted, rectangular strip D that is deformed isometrically into a closed ring S by connecting its short edges and specifying that its long edges are free of loading and, therefore, subject to zero traction and couple traction. The elementary example of a closed ring without twist as a state of relative minimum potential energy is discussed in detail, and the bending of the strip by opposing specific bending moments on its short edges is treated as a particular case. Finally, the constrained variational problem, with the introduction of appropriate constraint reactions as Lagrangian multipliers to account for the requirements that the deformation from D to S is isometric and that D is flat, is formulated in the spatial form, and the associated Euler-Lagrange equations are derived. We then solve the Euler-Lagrange equations for two representative problems in which a planar undistorted rectangular material strip is isometrically deformed by applied edge tractions and couple tractions (i.e., specific edge moments) into (i) a bent and twisted circular cylindrical helical state, and (ii) a state conformal with the surface of a right circular conical form.

Impact of interfacial imperfection on transverse wave in a functionally graded piezoelectric material structure with corrugated boundaries

NASA Astrophysics Data System (ADS)

Kumar Singh, Abhishek; Kumar, Santan; Kumari, Richa

2018-03-01

The propagation behavior of Love-type wave in a corrugated functionally graded piezoelectric material layered structure has been taken into account. Concretely, the layered structure incorporates a corrugated functionally graded piezoelectric material layer imperfectly bonded to a functionally graded piezoelectric material half-space. An analytical treatment has been employed to determine the dispersion relation for both cases of electrically open condition and electrically short condition. The phase velocity of the Love-type wave has been computed numerically and its dependence on the wave number has been depicted graphically for a specific type of corrugated boundary surfaces for both said conditions. The crux of the study lies in the fact that the imperfect bonding of the interface, the corrugated boundaries present in the layer, and the material properties of the layer and the half-space strongly influence the phase velocity of the Love-type wave. It can be remarkably noted that the imperfect bonding of the interface reduces the phase velocity of the Love-type wave significantly. As a special case of the problem, it is noticed that the procured dispersion relation for both cases of electrically open and electrically short conditions is in accordance with the classical Love wave equation.

Measuring space radiation shielding effectiveness

NASA Astrophysics Data System (ADS)

Bahadori, Amir; Semones, Edward; Ewert, Michael; Broyan, James; Walker, Steven

2017-09-01

Passive radiation shielding is one strategy to mitigate the problem of space radiation exposure. While space vehicles are constructed largely of aluminum, polyethylene has been demonstrated to have superior shielding characteristics for both galactic cosmic rays and solar particle events due to the high hydrogen content. A method to calculate the shielding effectiveness of a material relative to reference material from Bragg peak measurements performed using energetic heavy charged particles is described. Using accelerated alpha particles at the National Aeronautics and Space Administration Space Radiation Laboratory at Brookhaven National Laboratory, the method is applied to sample tiles from the Heat Melt Compactor, which were created by melting material from a simulated astronaut waste stream, consisting of materials such as trash and unconsumed food. The shielding effectiveness calculated from measurements of the Heat Melt Compactor sample tiles is about 10% less than the shielding effectiveness of polyethylene. Shielding material produced from the astronaut waste stream in the form of Heat Melt Compactor tiles is therefore found to be an attractive solution for protection against space radiation.

Optimization and management of materials in earthwork construction : final report, April 2010.

DOT National Transportation Integrated Search

2010-04-01

As a result of forensic investigations of problems across Iowa, a research study was developed aimed at providing solutions to identified : problems through better management and optimization of the available pavement geotechnical materials and throu...

Sunlight Diffusing Tent for Lunar Worksite

NASA Technical Reports Server (NTRS)

Burleson, Blair; Clark, Todd; Deese, Todd; Gentry, Ernest; Samad, Abdul

1990-01-01

The purpose is to provide a solution to problems astronauts encounter with sunlight on the lunar surface. Due to the absence of an atmosphere the Moon is subjected to intense sunlight creating problems with color and contrast. This problem can be overcome by providing a way to reduce intensity and diffuse the light in a working environment. The solution to the problem utilizes an umbrella, tent-like structure covered with a diffusing material. The design takes into account structural materials, stresses, fabrics, and deployment.

Graduate Student Program in Materials and Engineering Research and Development for Future Accelerators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spentzouris, Linda

The objective of the proposal was to develop graduate student training in materials and engineering research relevant to the development of particle accelerators. Many components used in today's accelerators or storage rings are at the limit of performance. The path forward in many cases requires the development of new materials or fabrication techniques, or a novel engineering approach. Often, accelerator-based laboratories find it difficult to get top-level engineers or materials experts with the motivation to work on these problems. The three years of funding provided by this grant was used to support development of accelerator components through a multidisciplinary approachmore » that cut across the disciplinary boundaries of accelerator physics, materials science, and surface chemistry. The following results were achieved: (1) significant scientific results on fabrication of novel photocathodes, (2) application of surface science and superconducting materials expertise to accelerator problems through faculty involvement, (3) development of instrumentation for fabrication and characterization of materials for accelerator components, (4) student involvement with problems at the interface of material science and accelerator physics.« less

Naturally Occurring Radioactive Materials (NORM)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gray, P.

1997-02-01

This paper discusses the broad problems presented by Naturally Occuring Radioactive Materials (NORM). Technologically Enhanced naturally occuring radioactive material includes any radionuclides whose physical, chemical, radiological properties or radionuclide concentration have been altered from their natural state. With regard to NORM in particular, radioactive contamination is radioactive material in an undesired location. This is a concern in a range of industries: petroleum; uranium mining; phosphorus and phosphates; fertilizers; fossil fuels; forestry products; water treatment; metal mining and processing; geothermal energy. The author discusses in more detail the problem in the petroleum industry, including the isotopes of concern, the hazards theymore » present, the contamination which they cause, ways to dispose of contaminated materials, and regulatory issues. He points out there are three key programs to reduce legal exposure and problems due to these contaminants: waste minimization; NORM assesment (surveys); NORM compliance (training).« less

Membrane development for vanadium redox flow batteries.

PubMed

Schwenzer, Birgit; Zhang, Jianlu; Kim, Soowhan; Li, Liyu; Liu, Jun; Yang, Zhenguo

2011-10-17

Large-scale energy storage has become the main bottleneck for increasing the percentage of renewable energy in our electricity grids. Redox flow batteries are considered to be among the best options for electricity storage in the megawatt range and large demonstration systems have already been installed. Although the full technological potential of these systems has not been reached yet, currently the main problem hindering more widespread commercialization is the high cost of redox flow batteries. Nafion, as the preferred membrane material, is responsible for about 11% of the overall cost of a 1 MW/8 MWh system. Therefore, in recent years two main membrane related research threads have emerged: 1) chemical and physical modification of Nafion membranes to optimize their properties with regard to vanadium redox flow battery (VRFB) application; and 2) replacement of the Nafion membranes with different, less expensive materials. This review summarizes the underlying basic scientific issues associated with membrane use in VRFBs and presents an overview of membrane-related research approaches aimed at improving the efficiency of VRFBs and making the technology cost-competitive. Promising research strategies and materials are identified and suggestions are provided on how materials issues could be overcome.

Facilitating students' application of the integral and the area under the curve concepts in physics problems

NASA Astrophysics Data System (ADS)

Nguyen, Dong-Hai

This research project investigates the difficulties students encounter when solving physics problems involving the integral and the area under the curve concepts and the strategies to facilitate students learning to solve those types of problems. The research contexts of this project are calculus-based physics courses covering mechanics and electromagnetism. In phase I of the project, individual teaching/learning interviews were conducted with 20 students in mechanics and 15 students from the same cohort in electromagnetism. The students were asked to solve problems on several topics of mechanics and electromagnetism. These problems involved calculating physical quantities (e.g. velocity, acceleration, work, electric field, electric resistance, electric current) by integrating or finding the area under the curve of functions of related quantities (e.g. position, velocity, force, charge density, resistivity, current density). Verbal hints were provided when students made an error or were unable to proceed. A total number of 140 one-hour interviews were conducted in this phase, which provided insights into students' difficulties when solving the problems involving the integral and the area under the curve concepts and the hints to help students overcome those difficulties. In phase II of the project, tutorials were created to facilitate students' learning to solve physics problems involving the integral and the area under the curve concepts. Each tutorial consisted of a set of exercises and a protocol that incorporated the helpful hints to target the difficulties that students expressed in phase I of the project. Focus group learning interviews were conducted to test the effectiveness of the tutorials in comparison with standard learning materials (i.e. textbook problems and solutions). Overall results indicated that students learning with our tutorials outperformed students learning with standard materials in applying the integral and the area under the curve concepts to physics problems. The results of this project provide broader and deeper insights into students' problem solving with the integral and the area under the curve concepts and suggest strategies to facilitate students' learning to apply these concepts to physics problems. This study also has significant implications for further research, curriculum development and instruction.

Potential Applications of Smart Multifunctional Wearable Materials to Gerontology.

PubMed

Armstrong, David G; Najafi, Bijan; Shahinpoor, Mohsen

2017-01-01

Smart multifunctional materials can play a constructive role in addressing some very important aging-related issues. Aging affects the ability of older adults to continue to live safely and economically in their own residences for as long as possible. Thus, there will be a greater need for preventive, acute, rehabilitative, and long-term health care services for older adults as well as a need for tools to enable them to function independently during daily activities. The objective of this paper is, thus, to present a comprehensive review of some potential smart materials and their areas of applications to gerontology. Thus, brief descriptions of various currently available multifunctional smart materials and their possible applications to aging-related problems are presented. It is concluded that some of the most important applications to geriatrics may be in various sensing scenarios to collect health-related feedback or information and provide personalized care. Further described are the applications of wearable technologies to aging-related needs, including devices for home rehabilitation, remote monitoring, social well-being, frailty monitoring, monitoring of diabetes and wound healing and fall detection or prediction. It is also concluded that wearable technologies, when combined with an appropriate application and with appropriate feedback, may help improve activities and functions of older patients with chronic diseases. Finally, it is noted that methods developed to measure what one collectively manages in this population may provide a foundation to establish new definitions of quality of life. © 2017 S. Karger AG, Basel.

A Single-Expression Formula for Inverting Strain-Life and Stress-Strain Relationships

NASA Technical Reports Server (NTRS)

Manson, S. S.; Muralidharan, U.

1981-01-01

Starting with the basic fatigue lift formula, an inversion formula is derived. The inversion formula is valid over the entire life range of engineering interest for all materials examined. Conformity between the two equations is extremely close, suitable for all engineering problems. The approach used to invert the life relation is also suitable for the inversion of other formulas involving the sum of two power-law terms.

The Shock and Vibration Digest. Volume 16, Number 11

DTIC Science & Technology

1984-11-01

wave [19], a secular equation for Rayleigh waves on ing, seismic risk, and related problems are discussed. the surface of an anisotropic half-space...waves in an !so- tive equation of an elastic-plastic rack medium was....... tropic linear elastic half-space with plane material used; the coefficient...pair of semi-linear hyperbolic partial differential -- " Conditions under which the equations of motion equations governing slow variations in amplitude

Preliminary SP-100/Stirling Heat Exchanger Designs

NASA Astrophysics Data System (ADS)

Schmitz, Paul; Tower, Leonard; Dawson, Ronald; Blue, Brain; Dunn, Pat

1994-07-01

Analytic modeling of several heat exchanger concepts to couple the SP-100 nuclear reactor primary lithium loop and the Space Stirling Power Convertor(SSPC)was performed. Four 25 kWe SSPC's are used to produce the required 100 kW of electrical power. This design work focused on the interface between a single SSPC and the primary lithium loop. Manifolding to separate and collect the four channel flow was not modeled. This work modeled two separate types of heat exchanger interfaces (conductive coupling and radiative coupling) to explore their relative advantages and disadvantages. The minimum mass design of the conductively coupled concepts was 18 kg or 0.73 kg/kWe for a single 25 kWe convertor. The minimum mass radiatively coupled concept was 41 kg or 1.64 kg/kWe. The direct conduction heat exchanger provides a lighter weight system because of its ability to operate the Stirling convertor evaporator at higher heat fluxes than those attainable by the radiatively coupled systems. Additionally the conductively coupled concepts had relatively small volumes and provide potentially simpler assembly. Their disadvantages were the tight tolerances and material joining problems associated with this refractory to superalloy interface. The advantages of the radiatively coupled designs were the minimal material interface problems.

Preliminary SP-100/Stirling heat exchanger designs

NASA Astrophysics Data System (ADS)

Schmitz, Paul; Tower, Leonard; Dawson, Ronald; Blue, Brian; Dunn, Pat

1993-12-01

Analytic modeling of several heat exchanger concepts to couple the SP-100 nuclear reactor primary lithium loop and the Space Stirling Power Convertor (SSPC) was performed. Four 25 kWe SSPC's are used to produce the required 100 kW of electrical power. This design work focused on the interface between a single SSPC and the primary lithium loop. Manifolding to separate and collect the four channel flow was not modeled. This work modeled two separate types of heat exchanger interfaces (conductive coupling and radiative coupling) to explore their relative advantages and disadvantages. The minimum mass design of the conductively coupled concepts was 18 kg or 0.73 kg/kWe for a single 25 kWe convertor. The minimum mass radiatively coupled concept was 41 kg or 1.64 kg/kWe. The direct conduction heat exchanger provides a lighter weight system because of its ability to operate the Stirling convertor evaporator at higher heat fluxes than those attainable by the radiatively coupled systems. Additionally the conductively coupled concepts had relatively small volumes and provide potentially simpler assembly. Their disadvantages were the tight tolerances and material joining problems associated with this refractory to superalloy interface. The advantages of the radiatively coupled designs were the minimal material interface problems.

Preliminary SP-100/Stirling heat exchanger designs

NASA Technical Reports Server (NTRS)

Schmitz, Paul; Tower, Leonard; Dawson, Ronald; Blue, Brian; Dunn, Pat

1993-01-01

Analytic modeling of several heat exchanger concepts to couple the SP-100 nuclear reactor primary lithium loop and the Space Stirling Power Convertor (SSPC) was performed. Four 25 kWe SSPC's are used to produce the required 100 kW of electrical power. This design work focused on the interface between a single SSPC and the primary lithium loop. Manifolding to separate and collect the four channel flow was not modeled. This work modeled two separate types of heat exchanger interfaces (conductive coupling and radiative coupling) to explore their relative advantages and disadvantages. The minimum mass design of the conductively coupled concepts was 18 kg or 0.73 kg/kWe for a single 25 kWe convertor. The minimum mass radiatively coupled concept was 41 kg or 1.64 kg/kWe. The direct conduction heat exchanger provides a lighter weight system because of its ability to operate the Stirling convertor evaporator at higher heat fluxes than those attainable by the radiatively coupled systems. Additionally the conductively coupled concepts had relatively small volumes and provide potentially simpler assembly. Their disadvantages were the tight tolerances and material joining problems associated with this refractory to superalloy interface. The advantages of the radiatively coupled designs were the minimal material interface problems.

Engineering specification and system design for CAD/CAM of custom shoes: UMC project effort

NASA Technical Reports Server (NTRS)

Bao, Han P.

1990-01-01

Further experimentations were made to improve the design and fabrication techniques of the integrated sole. The sole design is shown to be related to the foot position requirements and the actual shape of the foot including presence of neurotropic ulcers or other infections. Factors for consideration were: heel pitch, balance line, and rigidity conditions of the foot. Machining considerations were also part of the design problem. Among these considerations, widths of each contour, tool motion, tool feed rate, depths of cut, and slopes of cut at the boundary were the key elements. The essential fabrication techniques evolved around the idea of machining a mold then, using quick-firm latex material, casting the sole through the mold. Two main mold materials were experimented with: plaster and wood. Plaster was very easy to machine and shape but could barely support the pressure in the hydraulic press required by the casting process. Wood was found to be quite effective in terms of relative cost, strength, and surface smoothness except for the problem of cutting against the fibers which could generate ragged surfaces. The programming efforts to convert the original dBase programs into C programs so that they could be executed on the SUN Computer at North Carolina State University are discussed.

Sampling errors in blunt dust samplers arising from external wall loss effects

NASA Astrophysics Data System (ADS)

Vincent, J. H.; Gibson, H.

Evidence is given that, with some forms of blunt dust sampler under conditions relating to those encountered in practical occupational hygiene and environmental monitoring, particles which impact onto the outer surface of the sampler body may not adhere permanently, and may eventually enter the sampling orifice. The effect of such external wall loss is to bring about excess sampling, where errors as high as 100% could arise. The problem is particularly important in the sampling of dry airborne particulates of the type commonly found in practical situations. For a given sampler configuration, the effect becomes more marked as the particle size increases or as the ratio of sampling velocity to ambient wind speed increases. We would expect it be greater for gritty, crystalline material than for smoother, amorphous material. Possible mechanisms controlling external wall losses were examined, and it was concluded that particle 'blow-off' (as opposed to particle 'bounce') is the most plausible. On the basis of simple experiments, it might be possible to make corrections for the sampling errors in question, but caution is recommended in doing so because of the unpredictable effects of environmental factors such as temperature and relative humidity. Of the possible practical solutions to the problem, it is felt that the best approach lies in the correct choice of sampler inlet design.

An Experimental Copyright Moratorium: Study of a Proposed Solution to the Copyright Photocopying Problem. Final Report to the American Society for Testing and Materials (ASTM).

ERIC Educational Resources Information Center

Heilprin, Laurence B.

The Committee to Investigate Copyright Problems (CICP), a non-profit organization dedicated to resolving the conflict known as the "copyright photocopying problem" was joined by the American Society for Testing and Materials (ASTM), a large national publisher of technical and scientific standards, in a plan to simulate a long-proposed…

Implementation of Problem Based Learning Model in Concept Learning Mushroom as a Result of Student Learning Improvement Efforts Guidelines for Teachers

ERIC Educational Resources Information Center

Rubiah, Musriadi

2016-01-01

Problem based learning is a training strategy, students work together in groups, and take responsibility for solving problems in a professional manner. Instructional materials such as textbooks become the main reference of students in study of mushrooms, especially the material is considered less effective in responding to the information needs of…

Polymeric metallic electrodes for rechargeable battery applications

NASA Technical Reports Server (NTRS)

Somoano, R.

1982-01-01

A review is presented on the status of plastic metal electrodes, emphasizing the use of polyacetylene as a prototype polymeric material. The electrochemical characteristics of polyacetylene are examined; and the potential use of this material, as well as other types of plastic metal electrodes, in batteries is evaluated. Several problem areas which must be solved before polyacetylene can be widely used in battery applications are discussed, including the problem of electrolyte stability, the problem that the depth of discharge and the energy density is limited by the metal-semiconductor transition, and also the poor electrochemical performance of impure material.

Materials Problems in Chemical Liquid-Propellant Rocket Systems

NASA Technical Reports Server (NTRS)

Gilbert, L. L.

1959-01-01

With the advent of the space age, new adjustments in technical thinking and engineering experience are necessary. There is an increasing and extensive interest in the utilization of materials for components to be used at temperatures ranging from -423 to over 3500 deg F. This paper presents a description of the materials problems associated with the various components of chemical liquid rocket systems. These components include cooled and uncooled thrust chambers, injectors, turbine drive systems, propellant tanks, and cryogenic propellant containers. In addition to materials limitations associated with these components, suggested research approaches for improving materials properties are made. Materials such as high-temperature alloys, cermets, carbides, nonferrous alloys, plastics, refractory metals, and porous materials are considered.

Association between neighborhood-level deprivation and disability in a community sample of people with diabetes.

PubMed

Schmitz, Norbert; Nitka, Danit; Gariepy, Genevieve; Malla, Ashok; Wang, JianLi; Boyer, Richard; Messier, Lyne; Strychar, Irene; Lesage, Alain

2009-11-01

The objective of the present study was to analyze the association between neighborhood deprivation and self-reported disability in a community sample of people with type 2 diabetes. Random digit dialing was used to select a sample of adults with self-reported diabetes aged 18-80 years in Quebec, Canada. Health status was assessed by the World Health Organization Disability Assessment Schedule II. Material and social deprivation was measured using the Pampalon index, which is based on the Canadian Census. Potential risk factors for disability included sociodemographic characteristics, socioeconomic status, social support, lifestyle-related factors (smoking, physical activity, and BMI), health care-related problems, duration of diabetes, insulin use, and diabetes-specific complications. There was a strong association between disability and material and social deprivation in our sample (n = 1,439): participants living in advantaged neighborhoods had lower levels of disability than participants living in disadvantaged neighborhoods. The means +/- SD disability scores for men were 7.8 +/- 11.8, 12.0 +/- 11.8, and 18.1 +/- 19.4 for low, medium, and high deprivation areas, respectively (P < 0.001). The disability scores for women were 13.4 +/- 12.4, 14.8 +/- 15.9, and 18.9 +/- 16.2 for low, medium, and high deprivation areas, respectively (P < 0.01). Neighborhood deprivation was associated with disability even after controlling for education, household income, sociodemographic characteristics, race, lifestyle-related behaviors, social support, diabetes-related variables, and health care access problems. The inclusion of neighborhood characteristics might be an important step in the identification and interpretation of risk factors for disability in diabetes.

Stability and Process of Destruction of Compressed Plate of Layered Composite Materials With Defects

NASA Astrophysics Data System (ADS)

Bokhoeva, L. A.; Rogov, V. E.; Chermoshentseva, A. S.; Lobanov, D. V.

2016-08-01

Interlayer defects in composite materials are a pressing problem, which affecting their performance characteristics. In this research, we considered the problem of the stability and of the fracture process of the compressed thin plate made of laminated composite materials with the interlayer defects. In this research we had got a critical equation for a plate with interlayer defect. The experiment showed the effect and the quantity of nano-dispersed additives on the mechanical properties of composite materials with interlayer defects.