Evolution of mechanical properties of M50 bearing steel due to rolling contact fatigue

NASA Astrophysics Data System (ADS)

Allison, Bryan D.

Current bearing life models significantly under predict the life of bearings made of modern ultra-clean steels. New life models that include the constitutive response of the material are needed. However, the constitutive response of bearing steel is known to change during bearing operation. In the current study, the evolution of the mechanical properties of M50 bearing steel due to rolling contact fatigue (RCF) was investigated. A combination of M50 balls and rods were subjected to RCF testing under various conditions (e.g. number of RCF cycles, applied Hertzian stress, and interacting material). Additionally, some of the balls tested went through a proprietary mechanical process to induce compressive residual stresses over the first several hundred microns into the depth of the ball prior to RCF testing. After RCF testing, the specimens were subjected to a number of tests. First, the residual stresses within the subsurface RCF affected region were measured via x-ray diffraction. The residual stresses within the mechanically processed (MP) balls were found to not significantly change due to RCF, while a linear relationship was found between the maximum residual stress with the RCF affected zone and the Hertzian stress for the unprocessed balls. Then, the specimens were sectioned, polished, and chemically etched to study the evolution of the microstructure due to RCF. A similar relationship was found between the size of the dark etching region (DER) and the Hertzian stress. Formation of a light etching region (LER) is demonstrated to not correlate with a decrease in material strength and hardness, but it does serve as a predictor for failure due to spall. Micro-indentation was performed within subsurface to estimate the local yield stress. Micro-indentation is not able to provide information about the stress-strain response, only the yield strength. Hence, a novel method to extract and test miniature compression specimens from within the RCF affected regions of balls after RCF was developed. Using this method, it is possible to determine the full stress-strain response of material after material that has undergone RCF. The micro-hardness of the material within the RCF affected region was found to increase by nearly 10% and yield strength increased 13% when high contact stress levels were employed in fatigue experiments. It was demonstrated that the number of cycles does contribute to hardness increase, but the applied Hertzian stress is the dominant factor. Mechanical processing was found to significantly retard the rate of mechanical property evolution, implying that it would also significantly improve the life. Similarly, it was observed that the rate of hardening is slower when silicon nitride is used to interact with the M50 specimen than another M50 component. This supports the idea that hybrid bearings last longer than more traditional all-steel bearings. Finally, an empirical model of the evolution of the constitutive response of the bearing material within the RCF affected region was developed based on the results of these analyses. This model can be used to predict the constitutive response of the material within the RCF affected region of an M50 steel ball, given the initial hardness, number of RCF cycles, and applied Hertzian stress. Further, it is now possible to solve the local yield strength as a function of depth within the RCF affected region given these same parameters.

Influence of citric acid on the surface texture of glass ionomer restorative materials

PubMed Central

Reddy, Dappili Swami Ranga; Kumar, Ramachandran Anil; Venkatesan, Sokkalingam Mothilal; Narayan, Gopal Shankar; Duraivel, Dasarathan; Indra, Rajamani

2014-01-01

Aim: This study determined the effectiveness of G-coat plus surface protective agent over petroleum jelly on the surface texture of conventional Glass ionomer restorative materials. Materials and Methods: Three chemically cured conventional glass ionomer restorative materials type II, type IX and ketac molar were evaluated in this study. Sixty specimens were made for each restorative material. They were divided into two groups of thirty specimens each. Of the sixty specimens, thirty were coated with G-coat plus (a nano-filler coating) and the rest with petroleum jelly. Thirty samples of both protective coating agents were randomly divided into six groups of five specimens and conditioned in citric acid solutions of differing pH (pH 2, 3, 4, 5, 6 & 7). Each specimen was kept in citric acid for three hours a day, and the rest of time stored in salivary substitute. This procedure was repeated for 8 days. After conditioning, the surface roughness (Ra, μm) of each specimen was measured using a surface profilometer (Taylor & Habson, UK). Data was analyzed using one-way analysis of variance (ANOVA) and Tukey's HSD test at a significance level of 0.05. Results: The surface textures of all the tested glass ionomer restorative materials protected with G-coat plus were not significantly affected by acids at low pH. The surface textures of all the tested glass ionomer restorative materials protected with petroleum jelly coating were significantly affected by acids at low pH. Conclusion: The effects of pH on the surface texture of glass ionomer restoratives are material dependent. Among all the materials tested the surface texture of Type II GIC (Group I) revealed marked deterioration when conditioned in solutions of low pH and was statistically significant. Hence, a protective coating either with G-coat plus or with light polymerized low viscosity unfilled resin adhesives is mandatory for all the glass ionomer restorations to increase the wear resistance of the restorative materials. PMID:25298643

Influence of weight and type of planting material on fruit quality and its heterogeneity in pineapple [Ananas comosus (L.) Merrill].

PubMed

Fassinou Hotegni, V Nicodème; Lommen, Willemien J M; Agbossou, Euloge K; Struik, Paul C

2014-01-01

Cultural practices can affect the quality of pineapple fruits and its variation. The objectives of this study were to investigate (a) effects of weight class and type of planting material on fruit quality, heterogeneity in quality and proportion and yield of fruits meeting European export standards, and (b) the improvement in quality, proportion and yield of fruits meeting export standards when flowering was induced at optimum time. Experiments were conducted in Benin with cvs Sugarloaf (a Perola type) and Smooth Cayenne. In cv. Sugarloaf, experimental factors were weight class of planting material (light, mixed, heavy) and time of flowering induction (farmers', optimum) (Experiment 1). In cv. Smooth Cayenne an additional experimental factor was the type of planting material (hapas, ground suckers, a mixture of the two) (Experiment 2). Fruits from heavy planting material had higher infructescence and fruit weights, longer infructescences, shorter crowns, and smaller crown: infructescence length than fruits from light planting material. The type of planting material in Experiment 2 did not significantly affect fruit quality except crown length: fruits from hapas had shorter crowns than those from ground suckers. Crops from heavy planting material had a higher proportion and yield of fruits meeting export standards than those from other weight classes in Experiment 1 only; also the type of planting material in Experiment 2 did not affect these variates. Heterogeneity in fruit quality was usually not reduced by selecting only light or heavy planting material instead of mixing weights; incidentally the coefficient of variation was significantly reduced in fruits from heavy slips only. Heterogeneity was also not reduced by not mixing hapas and ground suckers. Flowering induction at optimum time increased the proportion and yield of fruits meeting export standards in fruits from light and mixed slip weights and in those from the mixture of heavy hapas plus ground suckers.

Influence of weight and type of planting material on fruit quality and its heterogeneity in pineapple [Ananas comosus (L.) Merrill

PubMed Central

Fassinou Hotegni, V. Nicodème; Lommen, Willemien J. M.; Agbossou, Euloge K.; Struik, Paul C.

2015-01-01

Cultural practices can affect the quality of pineapple fruits and its variation. The objectives of this study were to investigate (a) effects of weight class and type of planting material on fruit quality, heterogeneity in quality and proportion and yield of fruits meeting European export standards, and (b) the improvement in quality, proportion and yield of fruits meeting export standards when flowering was induced at optimum time. Experiments were conducted in Benin with cvs Sugarloaf (a Perola type) and Smooth Cayenne. In cv. Sugarloaf, experimental factors were weight class of planting material (light, mixed, heavy) and time of flowering induction (farmers', optimum) (Experiment 1). In cv. Smooth Cayenne an additional experimental factor was the type of planting material (hapas, ground suckers, a mixture of the two) (Experiment 2). Fruits from heavy planting material had higher infructescence and fruit weights, longer infructescences, shorter crowns, and smaller crown: infructescence length than fruits from light planting material. The type of planting material in Experiment 2 did not significantly affect fruit quality except crown length: fruits from hapas had shorter crowns than those from ground suckers. Crops from heavy planting material had a higher proportion and yield of fruits meeting export standards than those from other weight classes in Experiment 1 only; also the type of planting material in Experiment 2 did not affect these variates. Heterogeneity in fruit quality was usually not reduced by selecting only light or heavy planting material instead of mixing weights; incidentally the coefficient of variation was significantly reduced in fruits from heavy slips only. Heterogeneity was also not reduced by not mixing hapas and ground suckers. Flowering induction at optimum time increased the proportion and yield of fruits meeting export standards in fruits from light and mixed slip weights and in those from the mixture of heavy hapas plus ground suckers. PMID:25653659

Electrostatic atomization: Effect of electrode materials on electrostatic atomizer performance

NASA Astrophysics Data System (ADS)

Sankaran, Abhilash; Staszel, Christopher; Kashir, Babak; Perri, Anthony; Mashayek, Farzad; Yarin, Alexander

2016-11-01

Electrostatic atomization was studied experimentally with a pointed electrode in a converging nozzle. Experiments were carried out on poorly conductive canola oil where it was observed that electrode material may affect charge transfer. This points at the possible faradaic reactions that can occur at the surfaces of the electrodes. The supply voltage is applied to the sharp electrode and the grounded nozzle body constitutes the counter-electrode. The charge transfer is controlled by the electrochemical reactions on both the electrodes. The electrical performance study of the atomizer issuing a charged oil jet was conducted using three different nozzle body materials - brass, copper and stainless steel. Also, two sharp electrode materials - brass and stainless steel - were tested. The experimental results revealed that both the nozzle body material, as well as the sharp electrode material affected the spray and leak currents. Moreover, the effect of the sharp electrode material is quite significant. This research is supported by NSF Grant 1505276.

Increased susceptibility of skin from HERDA (Hereditary Equine Regional Dermal Asthenia)-affected horses to bacterial collagenase degradation: a potential contributing factor to the clinical signs of HERDA.

PubMed

Rashmir-Raven, Ann; Lavagnino, Michael; Sedlak, Aleksa; Gardner, Keri; Arnoczky, Steven

2015-12-01

Hereditary equine regional dermal asthenia (HERDA) is a genetic disorder of collagen resulting in fragile, hyper-extensible skin and ulcerative lesions. The predominance of skin lesions have been shown to occur on the dorsum of HERDA-affected horses. While this has been postulated to be due to increased exposure to sunlight of these areas, the precise pathological mechanism which causes this to occur is unclear. We hypothesized that an increase in collagenase activity, that has been associated with the exposure of dermal fibroblasts to sunlight, will significantly degrade the material properties of skin from HERDA-affected horses when compared to unaffected controls. Six unaffected and seven HERDA-affected horses, all euthanized for other reasons. Full-thickness skin samples from similar locations on each horse were collected and cut into uniform strips and their material properties (tensile modulus) determined by mechanical testing before (n = 12 samples/horse) or after (n = 12 samples/horse) incubation in bacterial collagenase at 37°C for 6 h. The change in modulus following treatment was then compared between HERDA-affected and unaffected horses using a Student's t-test. The modulus of skin from HERDA-affected horses decreased significantly more than that from unaffected horses following collagenase treatment (54 ± 7% versus 30 ± 16%, P = 0.004). The significant decrease in the modulus of skin from HERDA-affected horses following collagenase exposure suggests that their altered collagen microarchitecture is more susceptible to enzymatic degradation and may explain the localization of skin lesions in HERDA-affected horses to those areas of the body most exposed to sunlight. These findings appear to support the previously reported benefits of sunlight restriction in HERDA-affected horses. © 2015 ESVD and ACVD.

Influence of citric acid on the surface texture of glass ionomer restorative materials.

PubMed

Reddy, Dappili Swami Ranga; Kumar, Ramachandran Anil; Venkatesan, Sokkalingam Mothilal; Narayan, Gopal Shankar; Duraivel, Dasarathan; Indra, Rajamani

2014-09-01

This study determined the effectiveness of G-coat plus surface protective agent over petroleum jelly on the surface texture of conventional Glass ionomer restorative materials. Three chemically cured conventional glass ionomer restorative materials type II, type IX and ketac molar were evaluated in this study. Sixty specimens were made for each restorative material. They were divided into two groups of thirty specimens each. Of the sixty specimens, thirty were coated with G-coat plus (a nano-filler coating) and the rest with petroleum jelly. Thirty samples of both protective coating agents were randomly divided into six groups of five specimens and conditioned in citric acid solutions of differing pH (pH 2, 3, 4, 5, 6 & 7). Each specimen was kept in citric acid for three hours a day, and the rest of time stored in salivary substitute. This procedure was repeated for 8 days. After conditioning, the surface roughness (Ra, μm) of each specimen was measured using a surface profilometer (Taylor & Habson, UK). Data was analyzed using one-way analysis of variance (ANOVA) and Tukey's HSD test at a significance level of 0.05. The surface textures of all the tested glass ionomer restorative materials protected with G-coat plus were not significantly affected by acids at low pH. The surface textures of all the tested glass ionomer restorative materials protected with petroleum jelly coating were significantly affected by acids at low pH. The effects of pH on the surface texture of glass ionomer restoratives are material dependent. Among all the materials tested the surface texture of Type II GIC (Group I) revealed marked deterioration when conditioned in solutions of low pH and was statistically significant. Hence, a protective coating either with G-coat plus or with light polymerized low viscosity unfilled resin adhesives is mandatory for all the glass ionomer restorations to increase the wear resistance of the restorative materials.

The Effect of Preventive Agents (Mouthwashes/Gels) on the Color Stability of Dental Resin-Based Composite Materials

PubMed Central

Al-Samadani, Khalid H.

2017-01-01

The color of dental restorative material should be maintained throughout its functional lifetime in an oral environment. However, the frequent use of mouthwash may affect the color stability of these composite restorations. The aim of this study is to assess the effects of using various mouthwashes on the color stability of various dental restorative composite materials. For this purpose, four mouthwashes/gels (Flocare gel (0.4% stannous fluoride), Pascal gel (topical APF fluoride), Pro-Relief mouthwash (sodium fluoride), and Plax Soin mouthwash (sodium fluoride)), and distilled water as a control, were selected. These were divided into five groups: Group 1: Flocare gel; Group 2: Pascal gel; Group 3: Pro-Relief mouthwash; Group 4: Plax Soin mouthwash; and Group 5: distilled water (control). Prepared restorative materials samples were immersed in the groups of mouthwashes/gels and the distilled water (control) for 24, 48, and 72 h. The discoloration that all materials exhibited with all immersion groups was significantly different at each of the three time periods for all groups (p < 0.05). Results from immersion in Flocare gel, Pascal gel, Pro-Relief mouthwash, and Plax Soin mouthwash were statistically significant (p < 0.05). The color change chroma was not significant for Pro-Relief and Plax Soin mouthwash (p > 0.05). Mouthwashes/gels affect color shifting for all composite resin materials, and changes are exaggerated over time. However, discoloration effects are not perceptible to the human eye. PMID:29563424

Biodiversity, air quality and human health

Treesearch

David J. Nowak; Sarah Jovan; Christina Branquinho; Sofia Augusto; Manuel C. Ribeiro; Conor E. Kretsch

2015-01-01

Air pollution is a significant problem in cities across the world. It affects human health and well-being, ecosystem health, crops, climate, visibility and human-made materials. Health effects related to air pollution include its impact on the pulmonary, cardiac, vascular and neurological systems (Section 2). Trees affect air quality through a number of means (Section...

10 CFR 55.45 - Operating tests.

Code of Federal Regulations, 2010 CFR

2010-01-01

... significance of facility instrument readings. (5) Observe and safely control the operating behavior... equipment that could affect reactivity or the release of radioactive materials to the environment. (9...

Polymer microarray technology for stem cell engineering

PubMed Central

Coyle, Robert; Jia, Jia; Mei, Ying

2015-01-01

Stem cells hold remarkable promise for applications in tissue engineering and disease modeling. During the past decade, significant progress has been made in developing soluble factors (e.g., small molecules and growth factors) to direct stem cells into a desired phenotype. However, the current lack of suitable synthetic materials to regulate stem cell activity has limited the realization of the enormous potential of stem cells. This can be attributed to a large number of materials properties (e.g., chemical structures and physical properties of materials) that can affect stem cell fate. This makes it challenging to design biomaterials to direct stem cell behavior. To address this, polymer microarray technology has been developed to rapidly identify materials for a variety of stem cell applications. In this article, we summarize recent developments in polymer array technology and their applications in stem cell engineering. Statement of significance Stem cells hold remarkable promise for applications in tissue engineering and disease modeling. In the last decade, significant progress has been made in developing chemically defined media to direct stem cells into a desired phenotype. However, the current lack of the suitable synthetic materials to regulate stem cell activities has been limiting the realization of the potential of stem cells. This can be attributed to the number of variables in material properties (e.g., chemical structures and physical properties) that can affect stem cells. Polymer microarray technology has shown to be a powerful tool to rapidly identify materials for a variety of stem cell applications. Here we summarize recent developments in polymer array technology and their applications in stem cell engineering. PMID:26497624

Soil hydrological and soil property changes resulting from termite activity on agricultural fields in Burkina Faso

NASA Astrophysics Data System (ADS)

Mettrop, I.; Cammeraat, L. H.; Verbeeten, E.

2009-04-01

Termites are important ecosystem-engineers in subtropical and tropical regions. The effect of termite activity affecting soil infiltration is well documented in the Sahelian region. Most studies find increased infiltration rates on surfaces that are affected by termite activity in comparison to crusted areas showing non-termite presence. Crusted agricultural fields in the Sanmatenga region in Burkina Faso with clear termite activity were compared to control fields without visual ground dwelling termite activity. Fine scale rainfall simulations were carried out on crusted termite affected and control sites. Furthermore soil moisture change, bulk density, soil organic matter as well as general soil characteristics were studied. The top soils in the study area were strongly crusted (structural crust) after the summer rainfall and harvest of millet. They have a loamy sand texture underlain by a shallow sandy loam Bt horizon. The initial soil moisture conditions were significantly higher on the termite plots when compared to control sites. It was found that the amount of runoff produced on the termite plots was significantly higher, and also the volumetric soil moisture content after the experiments was significantly lower if compared to the control plots. Bulk density showed no difference whereas soil organic matter was significantly higher under termite affected areas, in comparison to the control plots. Lab tests showed no significant difference in hydrophobic behavior of the topsoil and crust material. Micro and macro-structural properties of the topsoil did not differ significantly between the termite sites and the control sites. The texture of the top 5 cm of the soil was also found to be not significantly different. The infiltration results are contradictory to the general literature, which reports increased infiltration rates after prolonged termite activity although mostly under different initial conditions. The number of nest entrances was clearly higher in the termite areas, but apparently did not significantly affect infiltration. The increased soil organic matter contents in the termite affected areas however, are as expected from literature, but did not improve soil aggregation which would be expected given the importance of organic matter in soil aggregation in this type of soils. One of the explanations for the reduced infiltration rates might be that termites bring clay from the finer textured subsoil to the surface to build casts over the organic material on the surface (mainly millet stems). It is speculated that the excavated clay material could be involved in crust formation, only present is in the upper 0.5 cm of the soil crust, which is enough to block pores in the crust surface, hampering infiltration. The topsoil aggregates are slaking under the summer rainfall and the increase in fine textured material, excavated by the termites, could be incorporated into the crust and reduce infiltration. Furthermore this specific effect might also be related to the type of termite involved, as impacts from ecosystem engineers on their environment is highly dependent on the specific species involved.

The effect of repeated firings on the color change of dental ceramics using different glazing methods

PubMed Central

Yılmaz, Kerem; Ozturk, Caner

2014-01-01

PURPOSE Surface color is one of the main criteria to obtain an ideal esthetic. Many factors such as the type of the material, surface specifications, number of firings, firing temperature and thickness of the porcelain are all important to provide an unchanged surface color in dental ceramics. The aim of this study was to evaluate the color changes in dental ceramics according to the material type and glazing methods, during the multiple firings. MATERIALS AND METHODS Three different types of dental ceramics (IPS Classical metal ceramic, Empress Esthetic and Empress 2 ceramics) were used in the study. Porcelains were evaluated under five main groups according to glaze and natural glaze methods. Color changes (ΔE) and changes in color parameters (ΔL, Δa, Δb) were determined using colorimeter during the control, the first, third, fifth, and seventh firings. The statistical analysis of the results was performed using ANOVA and Tukey test. RESULTS The color changes which occurred upon material-method-firing interaction were statistically significant (P<.05). ΔE, ΔL, Δa and Δb values also demonstrated a negative trend. The MC-G group was less affected in terms of color changes compared to other groups. In all-ceramic specimens, the surface color was significantly affected by multiple firings. CONCLUSION Firing detrimentally affected the structure of the porcelain surface and hence caused fading of the color and prominence of yellow and red characters. Compressible all-ceramics were remarkably affected by repeated firings due to their crystalline structure. PMID:25551001

Practical fundamentals of glass, rubber, and plastic sterile packaging systems.

PubMed

Sacha, Gregory A; Saffell-Clemmer, Wendy; Abram, Karen; Akers, Michael J

2010-01-01

Sterile product packaging systems consist of glass, rubber, and plastic materials that are in intimate contact with the formulation. These materials can significantly affect the stability of the formulation. The interaction between the packaging materials and the formulation can also affect the appropriate delivery of the product. Therefore, a parenteral formulation actually consists of the packaging system as well as the product that it contains. However, the majority of formulation development time only considers the product that is contained in the packaging system. Little time is spent studying the interaction of the packaging materials with the contents. Interaction between the packaging and the contents only becomes a concern when problems are encountered. For this reason, there are few scientific publications that describe the available packaging materials, their advantages and disadvantages, and their important product attributes. This article was created as a reference for product development and describes some of the packaging materials and systems that are available for parenteral products.

The role and importance of porosity in the deflagration rates of HMX-based materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glascoe, E A; Hsu, P C; Springer, H K

The deflagration behavior of thermally damaged HMX-based materials will be discussed. Strands of material were burned at pressures ranging from 10-300 MPa using the LLNL high pressure strand burner. Strands were heated in-situ and burned while still hot; temperatures range from 90-200 C and were chosen in order to allow for thermal damage of the material without significant decomposition of the HMX. The results indicate that multiple variables affect the burn rate but the most important are the polymorph of HMX and the nature and thermal stability of the non-HE portion of the material. Characterization of the strands indicate thatmore » the thermal soak produces significant porosity and permeability in the sample allowing for significantly faster burning due to the increased surface area and new pathways for flame spread into the material. Specifically, the deflagration rates of heated PBXN-9, LX-10, and PBX-9501 will be discussed and compared.« less

Study of residue type defect formation mechanism and the effect of advanced defect reduction (ADR) rinse process

NASA Astrophysics Data System (ADS)

Arima, Hiroshi; Yoshida, Yuichi; Yoshihara, Kosuke; Shibata, Tsuyoshi; Kushida, Yuki; Nakagawa, Hiroki; Nishimura, Yukio; Yamaguchi, Yoshikazu

2009-03-01

Residue type defect is one of yield detractors in lithography process. It is known that occurrence of the residue type defect is dependent on resist development process and the defect is reduced by optimized rinsing condition. However, the defect formation is affected by resist materials and substrate conditions. Therefore, it is necessary to optimize the development process condition by each mask level. Those optimization steps require a large amount of time and effort. The formation mechanism is investigated from viewpoint of both material and process. The defect formation is affected by resist material types, substrate condition and development process condition (D.I.W. rinse step). Optimized resist formulation and new rinse technology significantly reduce the residue type defect.

Selective release of inorganic constituents in broiler manure biochars under different post-activation treatments

USDA-ARS?s Scientific Manuscript database

Previous studies determined that poultry litter is a desirable feedstock for activated biochars with enhanced adsorption towards cations. Animal manures such as poultry litter contain a significant fraction of inorganic material that can significantly affect the final physical, chemical and adsorpt...

An Investigation into the Effects of Interface Stress and Interfacial Arrangement on Temperature Dependent Thermal Properties of a Biological and a Biomimetic Material

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tomar, Vikas

2015-01-12

A significant effort in the biomimetic materials research is on developing materials that can mimic and function in the same way as biological tissues, on bio-inspired electronic circuits, on bio-inspired flight structures, on bio-mimetic materials processing, and on structural biomimetic materials, etc. Most structural biological and biomimetic material properties are affected by two primary factors: (1) interfacial interactions between an organic and an inorganic phase usually in the form of interactions between an inorganic mineral phase and organic protein network; and (2) structural arrangement of the constituents. Examples are exoskeleton structures such as spicule, nacre, and crustacean exoskeletons. A significantmore » effort is being directed towards making synthetic biomimetic materials based on a manipulation of the above two primary factors. The proposed research is based on a hypothesis that in synthetic materials with biomimetic morphology thermal conductivity, k, (how fast heat is carried away) and thermal diffusivity, D, (how fast a material’s temperature rises: proportional to the ratio of k and heat capacity) can be engineered to be either significantly low or significantly high based on a combination of chosen interface orientation and interfacial arrangement in comparison to conventional material microstructures with the same phases and phase volume fractions. METHOD DEVELOPMENT 1. We have established a combined Raman spectroscopy and nanomechanical loading based experimental framework to perform environment (liquid vs. air vs. vacuum) dependent and temperature dependent (~1000 degree-C) in-situ thermal diffusivity measurements in biomaterials at nanoscale to micron scale along with the corresponding analytical theoretic calculations. (Zhang and Tomar, 2013) 2. We have also established a new classical molecular simulation based framework to measure thermal diffusivity in biomolecular interfaces. We are writing a publication currently (Qu and Tomar, 2013) to report the framework and findings in tropocollagen-hydroxyapatite based idealized biomaterial interfaces. PHYSICAL FINDINGS 1. Analyses using experiments have revealed that in the case of bone thermal conductivity and thermal diffusivity at micron scale shows significant dependence on compressive stress and temperature. Overall, there is a decrease with respect to increase in temperature and increase with respect to increase in compressive stress. Bio-molecular simulations on idealized tropocollagen-hydroxyapatite interfaces confirm such findings. However, simulations also reveal that thermal diffusivity and thermal conductivity can be significantly tailored by interfacial orientation. More importantly, in inorganic materials, interfaces contribute to reduce thermal conductivity and diffusivity. However, analyses here reveal that both can be increased despite presence of a lot of interfaces. 2. Based on significant role played by interfaces in affecting bone thermal properties, a crustacean-exoskeleton system is examined for thermal diffusivity using the newly developed setup. Special emphasis here is on this system since such arrangement is found to be common in fresh water shrimp as well as in some deep water organisms surviving in environment extremes. Experiments reveal that in such system thermal diffusivity is highly tailorable. 3. Overall, experiments and models have established that in biomaterial interfaces a counterintuitive role of interfaces in mediating thermal conduction as a function of stress and temperature is possible in contrast to inorganic materials where interfaces almost always lead to reduction of thermal conductivity as a function of such factors. More investigations are underway to reveal physical origins of such counter-physical characteristics. Such principles can be significantly useful in developing new and innovative bioenergy and inorganic energy systems where heat dissipation significantly affects system performance.« less

Color Stability of New Esthetic Restorative Materials: A Spectrophotometric Analysis.

PubMed

Poggio, Claudio; Vialba, Lodovico; Berardengo, Anna; Federico, Ricaldone; Colombo, Marco; Beltrami, Riccardo; Scribante, Andrea

2017-07-06

The aim of this in vitro study was to evaluate and compare the color stability of different esthetic restorative materials (one microfilled composite, one nanofilled composite, one nanoceramic composite, one microfilled hybrid composite, one microfilled hybrid composite, one nanohybrid Ormocer based composite and one supra-nano spherical hybrid composite) after exposure to different staining solutions (physiological saline, red wine, coffee). All materials were prepared and polymerized into silicon rings (2 mm × 6 mm × 8 mm) to obtain specimens identical in size. Thirty cylindrical specimens of each material were prepared. Specimens were immersed in staining solutions (physiological saline, coffee and red wine) over a 28-day test period. A colorimetric evaluation according to the CIE L*a*b* system was performed by a blind trained operator at 7, 14, 21, 28 days of the staining process. The Shapiro-Wilk test and ANOVA were applied to assess significant differences among restorative materials. A paired t -test was applied to test which CIE L*a*b* parameters significantly changed after immersion in staining solutions. All restorative materials showed significant color differences after immersion in coffee. Coffee caused a significant color change in all types of tested composite resins. Only Filtek Supreme XTE demonstrated a staining susceptibility to red wine; no other significant differences among the materials were demonstrated. Long-term exposure to some food dyes (coffee in particular) can significantly affect the color stability of modern esthetic restorative materials regardless of materials' different compositions.

Compatibility testing of vacuum seal materials

NASA Astrophysics Data System (ADS)

Foster, P. A.; Rodin, W. A.

1993-05-01

Small scale materials compatibility testing was conducted for three elastomers considered for use as vacuum seal materials: Adiprene MOCA-cured; Adiprene Cyanacured; and Sylgard silastic rubber. The tests were conducted using orthogonal array designed experiments for each of the elastomers placed in contact with three materials commonly used during weapon disassembly operations: Duxseal, Sylgard 186 grease, and 2-propyl alcohol. The test results indicated that only the 2-propyl alcohol had a significant effect on the elastomer hardness and physical properties. The alcohol had the largest effect on the two Adiprene materials, and the silastic rubber was the least affected.

The Effect of the CAREY Program on the Students' Reading Attitude Towards Reading English Materials

ERIC Educational Resources Information Center

Al-Shawesh, Marwan Yahya; Hussin, Supyan

2015-01-01

Reading is one of language learning skills which has a great significance for the role it plays in the second language acquisition (SLA) process. The aim of this paper was to examine the extent to which the CAREY (Computer-Assisted Reading Yemen) program affects the Yemeni EFL students' reading attitude towards reading English materials. To…

Physicochemical properties affect the synthesis, controlled delivery, degradation and pharmacokinetics of inorganic nanoporous materials.

PubMed

Yazdi, Iman K; Ziemys, Arturas; Evangelopoulos, Michael; Martinez, Jonathan O; Kojic, Milos; Tasciotti, Ennio

2015-10-01

Controlling size, shape and uniformity of porous constructs remains a major focus of the development of porous materials. Over the past two decades, we have seen significant developments in the fabrication of new, porous-ordered structures using a wide range of materials, resulting in properties well beyond their traditional use. Porous materials have been considered appealing, due to attractive properties such as pore size length, morphology and surface chemistry. Furthermore, their utilization within the life sciences and medicine has resulted in significant developments in pharmaceutics and medical diagnosis. This article focuses on various classes of porous materials, providing an overview of principle concepts with regard to design and fabrication, surface chemistry and loading and release kinetics. Furthermore, predictions from a multiscale mathematical model revealed the role pore length and diameter could have on payload release kinetics.

The effect of greenhouse covering materials on phytochemical composition and antioxidant capacity of tomato cultivars.

PubMed

Ahmadi, Latifeh; Hao, Xiuming; Tsao, Rong

2018-02-13

The effect of light transmission (direct and diffuse) on the phenolic compounds of five tomato cultivars was investigated under controlled conditions in greenhouses covered with different covering materials. The type of covering material and type of diffusion of light simultaneously affected the reducing power of cultivars. Two-way analysis of variance showed statistically significant differences in total phenolic content for the different cultivars (P < 0.05) but not for the covering materials. Analysis by ultrahigh-performance liquid chromatography with diode array detection and liquid chromatography/tandem mass spectrometry showed the presence of major phenolic acid compounds such as chlorogenic acid, hydroxycinnamic acid/rutin, caffeic acid, ferulic acid and coumaric acid as well as flavonoid compounds such as myricetin, quercetin and naringenin. Most of the identified compounds showed a significant difference in different treatments due to both cultivar and covering material (P < 0.05). Statistical analysis showed that the type of covering material used influenced the total carotenoid and lycopene content (P < 0.05); however, the amount of lutein was not influenced by the type of covering material (P > 0.05). This study showed that the use of solar energy transmission could positively affect the reducing power of cultivars and alter the biosynthesis of certain phytochemicals that are health-beneficial. Further study could lead to applications for producing greenhouse vegetables with greater health attributes. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Influence of powder/liquid ratio on the radiodensity and diametral tensile strength of glass ionomer cements

PubMed Central

FONSECA, Rodrigo Borges; BRANCO, Carolina Assaf; QUAGLIATTO, Paulo Sérgio; GONÇALVES, Luciano de Souza; SOARES, Carlos José; CARLO, Hugo Lemes; CORRER-SOBRINHO, Lourenço

2010-01-01

Objective To determine the influence of P/L ratio on the radiodensity and diametral tensile strength (DTS) of glass ionomer cements. Material and Methods There were 2 factors under study: P/L ratio (manufacturer's recommended P/L ratio and a 50% reduced P/L ratio), and materials (Vitro Molar, Vitro Fil, Vitro Cem conventional GICs and Vitro Fil LC, Ortho Glass LC RMGICs). Five 1-mm-thick samples of each material-P/L ratio were produced for radiodensity evaluation. Samples were x-ray exposed onto Digora phosphor plate and radiodensity was obtained using the software Digora for Windows 2.5 Rev 0. For DTS, five (4.0x8.0 mm) cylinder samples of each material were tested (0.5 mm/min). Data were subjected to one- and two-way ANOVA (5x2) followed by Tukey's HSD test, or Kruskal-Wallis and Dunn's method. For paired comparisons, t-test or Mann-Whitney test were used (a=0.05). Results There was a significant interaction (P=0.001) for the studied factors (materials vs. P/L ratio). Reduced P/L ratio resulted in significantly lower DTS for the RMGICs, but radiodensity was affected for all materials (P<0.05). Conclusions Reduced P/L ratio affected properties of the tested glass ionomer cements. RMGICs were more susceptible to lower values of DTS, but radiodensity decreased for all materials following P/L ratio reduction. PMID:21308288

Improving the Sun Drying of Apricots (Prunus armeniaca) with Photo-Selective Dryer Cabinet Materials.

PubMed

Milczarek, Rebecca R; Avena-Mascareno, Roberto; Alonzo, Jérôme; Fichot, Mélissa I

2016-10-01

Photo-selective materials have been studied for their effects on the preharvest quality of horticultural crops, but little work has been done on potential postharvest processing effects. The aim of this work was to characterize the effects of 5 different photo-selective acrylic materials (used as the lid to a single-layer sun drying cabinet) on the drying rate and quality of apricots (Prunus armeniaca). Photo-selective cabinet materials that transmit light in the visible portion of the solar spectrum accelerate the apricots' drying rate in both the early period of drying and the course of drying as a whole. These materials do not significantly affect the measured quality metrics during the first day of sun drying. However, when drying is taken to completion, some minor but significant quality differences are observed. Infrared-blocking material produces dried apricot with lower red color, compared to clear, opaque black, and ultraviolet-blocking materials. Clear material produced dried apricot with significantly lower antioxidant activity, compared to black and infrared-blocking materials. Using appropriate photo-selective drying cabinet materials can reduce the required sun drying time for apricots by 1 to 2 d, compared with fully shaded drying. Ultraviolet-blocking material is recommended to maximize drying rate and minimize quality degradation. © 2016 Institute of Food Technologists®.

Color Stability of New Esthetic Restorative Materials: A Spectrophotometric Analysis

PubMed Central

Vialba, Lodovico; Federico, Ricaldone; Colombo, Marco; Beltrami, Riccardo

2017-01-01

The aim of this in vitro study was to evaluate and compare the color stability of different esthetic restorative materials (one microfilled composite, one nanofilled composite, one nanoceramic composite, one microfilled hybrid composite, one microfilled hybrid composite, one nanohybrid Ormocer based composite and one supra-nano spherical hybrid composite) after exposure to different staining solutions (physiological saline, red wine, coffee). All materials were prepared and polymerized into silicon rings (2 mm × 6 mm × 8 mm) to obtain specimens identical in size. Thirty cylindrical specimens of each material were prepared. Specimens were immersed in staining solutions (physiological saline, coffee and red wine) over a 28-day test period. A colorimetric evaluation according to the CIE L*a*b* system was performed by a blind trained operator at 7, 14, 21, 28 days of the staining process. The Shapiro–Wilk test and ANOVA were applied to assess significant differences among restorative materials. A paired t-test was applied to test which CIE L*a*b* parameters significantly changed after immersion in staining solutions. All restorative materials showed significant color differences after immersion in coffee. Coffee caused a significant color change in all types of tested composite resins. Only Filtek Supreme XTE demonstrated a staining susceptibility to red wine; no other significant differences among the materials were demonstrated. Long-term exposure to some food dyes (coffee in particular) can significantly affect the color stability of modern esthetic restorative materials regardless of materials’ different compositions. PMID:28684672

Effects of resource-dependent cannibalism on population size distribution and individual life history in a case-bearing caddisfly

PubMed Central

Okuda, Noboru

2018-01-01

Resource availability often determines the intensity of cannibalism, which has a considerable effect on population size distribution and individual life history. Larvae of the caddisfly Psilotreta kisoensis build portable cases from sedimentary sands and often display cannibalism. For this species, the availability of preferable case material is a critical factor that affects larval fitness, and material is locally variable depending on the underlying geology. In this study, we investigated how sand quality as a case material determines cannibalism frequency among larvae and, in turn, how the differential cannibalism frequency affects the body-size distribution and voltinism. Rearing experiments within a cohort revealed that a bimodal size distribution developed regardless of material quality. However, as the preferable material became abundant, the proportion of larger to smaller individuals increased. Consecutive experiments suggested that smaller larvae were more frequently cannibalized by larger ones and excluded from the population when preferable smooth material was abundant. This frequent cannibalism resulted in a bimodal size distribution with a significantly higher proportion of larger compared to smaller individuals. The size-dependent cannibalism was significantly suppressed when the larvae were raised in an environment with a scarcity of the preferable case material. This is probably because larvae cannot enjoy the benefit of rapid growth by cannibalism due to the difficulties in enlarging their case. At low cannibalism the growth of smaller individuals was stunted, and this was probably due to risk of cannibalism by larger individuals. This growth reduction in small individuals led to a bimodal size-distribution but with a lower proportion of larger to smaller individuals compared to at high cannibalism. A field study in two streams showed a similar size distribution of larvae as was found in the rearing experiment. The bimodal ratio has consequences for life history, since a size-bimodal population causes a cohort splitting: only larvae that were fully grown at 1 year had a univoltine life cycle, whereas larvae with a stunted growth continued their larval life for another year (semivoltine). This study suggests that availability of preferable case building material is an important factor that affects cannibalism, which in turn affects larval population size structure and cohort splitting. PMID:29466375

Effects of resource-dependent cannibalism on population size distribution and individual life history in a case-bearing caddisfly.

PubMed

Okano, Jun-Ichi; Okuda, Noboru

2018-01-01

Resource availability often determines the intensity of cannibalism, which has a considerable effect on population size distribution and individual life history. Larvae of the caddisfly Psilotreta kisoensis build portable cases from sedimentary sands and often display cannibalism. For this species, the availability of preferable case material is a critical factor that affects larval fitness, and material is locally variable depending on the underlying geology. In this study, we investigated how sand quality as a case material determines cannibalism frequency among larvae and, in turn, how the differential cannibalism frequency affects the body-size distribution and voltinism. Rearing experiments within a cohort revealed that a bimodal size distribution developed regardless of material quality. However, as the preferable material became abundant, the proportion of larger to smaller individuals increased. Consecutive experiments suggested that smaller larvae were more frequently cannibalized by larger ones and excluded from the population when preferable smooth material was abundant. This frequent cannibalism resulted in a bimodal size distribution with a significantly higher proportion of larger compared to smaller individuals. The size-dependent cannibalism was significantly suppressed when the larvae were raised in an environment with a scarcity of the preferable case material. This is probably because larvae cannot enjoy the benefit of rapid growth by cannibalism due to the difficulties in enlarging their case. At low cannibalism the growth of smaller individuals was stunted, and this was probably due to risk of cannibalism by larger individuals. This growth reduction in small individuals led to a bimodal size-distribution but with a lower proportion of larger to smaller individuals compared to at high cannibalism. A field study in two streams showed a similar size distribution of larvae as was found in the rearing experiment. The bimodal ratio has consequences for life history, since a size-bimodal population causes a cohort splitting: only larvae that were fully grown at 1 year had a univoltine life cycle, whereas larvae with a stunted growth continued their larval life for another year (semivoltine). This study suggests that availability of preferable case building material is an important factor that affects cannibalism, which in turn affects larval population size structure and cohort splitting.

Ultrasonically assisted drilling of rocks

NASA Astrophysics Data System (ADS)

Mikhailova, N. V.; Onawumi, P. Y.; Roy, A.; Silberschmidt, V. V.

2018-05-01

Conventional drilling of rocks can generate significant damage in the drilled material; a material layer is often split off a back surface of a sample during drilling, negatively affecting its strength. To improve finish quality, ultrasonically assisted drilling (UAD) was employed in two rocks - sandstone and marble. Damage areas in both materials were reduced in UAD when compared to conventional drilling. Reductions in a thrust force and a torque reduction were observed only for UAD in marble; ultrasonic assistance in sandstone drilling did not result in improvements in this regard.

Environmental effects on composite airframes: A study conducted for the ARM UAV Program (Atmospheric Radiation Measurement Unmanned Aerospace Vehicle)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Noguchi, R.A.

1994-06-01

Composite materials are affected by environments differently than conventional airframe structural materials are. This study identifies the environmental conditions which the composite-airframe ARM UAV may encounter, and discusses the potential degradation processes composite materials may undergo when subjected to those environments. This information is intended to be useful in a follow-on program to develop equipment and procedures to prevent, detect, or otherwise mitigate significant degradation with the ultimate goal of preventing catastrophic aircraft failure.

Color stability of esthetic restorative materials: a spectrophotometric analysis.

PubMed

Poggio, Claudio; Ceci, Matteo; Beltrami, Riccardo; Mirando, Maria; Wassim, Jaffal; Colombo, Marco

2016-12-01

Objective: The aim of this in vitro study was to evaluate the color stability of different restorative materials (one microfilled composite, one nanofilled composite, one nanohybrid composite and one Ormocer-based composite) after exposure to different staining solutions (coffee, coca-cola and red wine). Material and methods: All materials were polymerized into silicon rings (2 mm ×6 mm ×8 mm) to obtain specimens identical in size. Thirty cylindrical specimens of each material were prepared. They were immersed in staining solutions over a 28-day test period. A colorimetric evaluation according to the CIE L*a*b* system was performed by a blind trained operator at 7, 14, 21, 28 days of the staining process. The Shapiro-Wilk test and Kruskal-Wallis ANOVA were applied to assess significant differences among restorative materials. The paired t -test was applied to test which CIE L*a*b* parameters significantly changed after immersion in staining solutions. Results: All restorative materials showed clinically perceptible color differences after immersion in coffee. L* and b* values showed the highest variability. Coca cola and red wine did not influence the color stability for all restorative materials except for Filtek Supreme XTE. Conclusions: Coffee caused a significant color change in all types of tested composite resins. Filtek Supreme XTE demonstrated alone a staining susceptibility to red wine; no other significant differences among the materials were demonstrated. Long-term exposure to some food dyes (coffee in particular) can significantly affect the color stability of modern esthetic restorative materials regardless of materials' different composition.

The effect of fibre content, fibre size and alkali treatment to Charpy impact resistance of Oil Palm fibre reinforced composite material

NASA Astrophysics Data System (ADS)

Fitri, Muhamad; Mahzan, Shahruddin

2016-11-01

In this research, the effect of fibre content, fibre size and alkali treatment to the impact resistance of the composite material have been investigated, The composite material employs oil palm fibre as the reinforcement material whereas the matrix used for the composite materials are polypropylene. The Oil Palm fibres are prepared for two conditions: alkali treated fibres and untreated fibres. The fibre sizes are varied in three sizes: 5mm, 7mm and 10mm. During the composite material preparation, the fibre contents also have been varied into 3 different percentages: 5%, 7% and 10%. The statistical approach is used to optimise the variation of specimen determined by using Taguchi method. The results were analyzed also by the Taguchi method and shows that the Oil Palm fibre content is significantly affect the impact resistance of the polymer matrix composite. However, the fibre size is moderately affecting the impact resistance, whereas the fibre treatment is insignificant to the impact resistance of the oil palm fibre reinforced polymer matrix composite.

Frontal Polymerization in Microgravity

NASA Technical Reports Server (NTRS)

Pojman, John A.

1999-01-01

Frontal polymerization systems, with their inherent large thermal and compositional gradients, are greatly affected by buoyancy-driven convection. Sounding rocket experiments allowed the preparation of benchmark materials and demonstrated that methods to suppress the Rayleigh-Taylor instability in ground-based research did not significantly affect the molecular weight of the polymer. Experiments under weightlessness show clearly that bubbles produced during the reaction interact very differently than under 1 g.

Line defects in graphene: How doping affects the electronic and mechanical properties

NASA Astrophysics Data System (ADS)

Berger, Daniel; Ratsch, Christian

2016-06-01

Graphene and carbon nanotubes have extraordinary mechanical and electronic properties. Intrinsic line defects such as local nonhexagonal reconstructions or grain boundaries, however, significantly reduce the tensile strength, but feature exciting electronic properties. Here, we address the properties of line defects in graphene from first principles on the level of full-potential density-functional theory, and assess doping as one strategy to strengthen such materials. We carefully disentangle the global and local effect of doping by comparing results from the virtual crystal approximation with those from local substitution of chemical species, in order to gain a detailed understanding of the breaking and stabilization mechanisms. We find that doping primarily affects the occupation of the frontier orbitals. Occupation through n -type doping or local substitution with nitrogen increases the ultimate tensile strength significantly. In particular, it can stabilize the defects beyond the ultimate tensile strength of the pristine material. We therefore propose this as a key strategy to strengthen graphenic materials. Furthermore, we find that doping and/or applying external stress lead to tunable and technologically interesting metal/semiconductor transitions.

Affective Norms for 4900 Polish Words Reload (ANPW_R): Assessments for Valence, Arousal, Dominance, Origin, Significance, Concreteness, Imageability and, Age of Acquisition

PubMed Central

Imbir, Kamil K.

2016-01-01

In studies that combine understanding of emotions and language, there is growing demand for good-quality experimental materials. To meet this expectation, a large number of 4905 Polish words was assessed by 400 participants in order to provide a well-established research method for everyone interested in emotional word processing. The Affective Norms for Polish Words Reloaded (ANPW_R) is designed as an extension to the previously introduced the ANPW dataset and provides assessments for eight different affective and psycholinguistic measures of Valence, Arousal, Dominance, Origin, Significance, Concreteness, Imageability, and subjective Age of Acquisition. The ANPW_R is now the largest available dataset of affective words for Polish, including affective scores that have not been measured in any other dataset (concreteness and age of acquisition scales). Additionally, the ANPW_R allows for testing hypotheses concerning dual-mind models of emotion and activation (origin and subjective significance scales). Participants in the current study assessed all 4905 words in the list within 1 week, at their own pace in home sessions, using eight different Self-assessment Manikin (SAM) scales. Each measured dimension was evaluated by 25 women and 25 men. The ANPW_R norms appeared to be reliable in split-half estimation and congruent with previous normative studies in Polish. The quadratic relation between valence and arousal was found to be in line with previous findings. In addition, nine other relations appeared to be better described by quadratic instead of linear function. The ANPW_R provides well-established research materials for use in psycholinguistic and affective studies in Polish-speaking samples. PMID:27486423

Investigations on the effects of mouthrinses on the colour stability and surface roughness of different dental bioceramics

PubMed Central

Varol, Osman

2017-01-01

PURPOSE In this study, three bioceramic materials, [IPS Empress CAD (Ivoclar), IPS e.max CAD (Ivoclar), and Lava Ultimate CAD (3M ESPE)] were treated with three commercial mouthrinses [Listerine, Tantum Verde, and Klorhex]; and changes in colour reflectance and surface roughness values were then quantitatively assessed. MATERIALS AND METHODS One hundred and twenty ceramic samples, with dimensions of 2 × 12 × 14 mm, were prepared and divided into nine sample groups, except three control samples. The samples were immersed in the mouthrinse solutions for 120 hrs, and changes in colour reflectance and surface roughness values were measured by UV light spectrophotometry (Vita Easyshade; VITA Zahnfabrik) and by profilometer device (MitutoyoSurftest SJ-301), respectively. The change of surface roughness was inspected by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). RESULTS There was a positive correlation between the ΔE and increase in the surface roughness. Two of the ceramic materials, IPS Empress and Lava Ultimate, were affected significantly by the treatment of the mouthrinse solutions (P<.05). The most affecting solution was Tantum Verde and the most affected material was Lava Ultimate. As expected, the most resistant material to ΔE and chemical corrosion was IPS e max CAD among the materials used. CONCLUSION This work implied that mouthrinse with lower alcohol content had less deteriorating effect on colour and on the surface morphology of the bioceramic materials. PMID:28680552

How Molecular Structure Affects Mechanical Properties of an Advanced Polymer

NASA Technical Reports Server (NTRS)

Nicholson, Lee M.; Whitley, Karen S.; Gates, Thomas S.; Hinkley, Jeffrey A.

2000-01-01

density was performed over a range of temperatures below the glass transition temperature. The physical characterization, elastic properties and notched tensile strength all as a function of molecular weight and test temperature were determined. For the uncrosslinked SI material, it was shown that notched tensile strength is a strong function of both temperature and molecular weight, whereas stiffness is only a strong function of temperature. For the crosslinked PETI-SI material, it was shown that the effect of crosslinking significantly enhances the mechanical performance of the low molecular weight material; comparable to that exhibited by the high molecular weight material.

Comparison of the effect of different medicaments on surface reproduction of two commercially available Polyvinyl Siloxane impression materials - An Invitro Study

PubMed Central

Singh, Rina; Singh, Jagjit; Singh, Ramanpreet; Nanda, Sonia

2013-01-01

Objective:To determine the effect of different retraction cord medicaments on surface detail reproduction of polyvinyl siloxane impression materials and compare this effect on any two brands of commercially available polyvinyl siloxane impression materials. Material and methods: Four stainless steel dies were made according to ADA specification no.19. Three dies were treated with aluminium chloride (5%), ferric sulphate (13.3%) and epinephrine (0.1%) while the fourth one was left untreated to serve as control. Two impression materials (Dentsply and 3M ESPE) were used. Results: All the three medicaments adversely affected the surface detail reproduction of both the brands of the polyvinyl siloxane impression materials. These effects were statistically significant as compared to untreated control. The impressions of 3M ESPE brand have shown better surface detail reproduction as compared to Dentsply impression material. Conclusion: Surface detail reproduction of the polyvinyl siloxane impression materials is adversely affected by the retraction cord medicaments. The presence of moisture or any traces of the medicaments should be removed from the tooth surface to provide a dry field for the correct reproduction of the surface detail of these materials. Key words:Polyvinyl Siloxane, retraction cord medicaments, surface detail reproduction. PMID:24455069

Radiation sterilization of enzyme hybrids with biodegradable polymers

NASA Astrophysics Data System (ADS)

Furuta, Masakazu; Oka, Masahito; Hayashi, Toshio

2002-03-01

Ionizing radiations, which have already been utilized for the sterilization of medical supplies as well as gas fumigation, should be the final candidate to decontaminate "hybrid" biomaterials containing bio-active materials including enzymes because irradiation induces neither heat nor substances affecting the quality of the materials and our health. In order to check the feasibility of 60Co-gamma rays on these materials, we selected commercial proteases including papain and bromelain hybridized with commercial activated chitosan beads and demonstrated that these enzyme-hybrids suspended in water showed the significant radiation durability of more than twice as much as free enzyme solution at 25-kGy irradiation. Enhanced thermal and storage stability of the enzyme hybrids were not affected by the same dose level of irradiation, either, indicating that commercial irradiation sterilization method is applicable to enzyme hybrids without modification.

Occurrences of Indigestible Foreign Bodies in Cattle Slaughtered at Morogoro Municipal Slaughterhouse, Tanzania.

PubMed

Bwatota, S F; Makungu, M; Nonga, H E

2018-01-01

A cross-sectional study was conducted to determine the occurrence of indigestible foreign bodies (IFB) in cattle slaughtered at Morogoro Municipal Slaughterhouse, Tanzania. A total of 387 slaughter cattle were examined for presence of IFB. Out of 387 examined cattle, 93 (24.03%) had IFB in their forestomachs. The observed IFB were plastic bags, fruit seeds, clothing materials, ropes, hairballs, leather materials, stones, metallic nails, and wire. Plastic bags were the most frequently (50.5%) observed IFB followed by fruit seeds (18.3%). A significantly ( p < 0.05) high proportion of old animals (31.7%) had IFB compared to the young animals (21.2%). Similarly, the frequency of occurrence of IFB was significantly high ( p < 0.05) in crossbred dairy cattle (42.3%) compared to local breeds (22.7%). Cattle that appeared with poor body condition (37.8%) were found to be more affected ( p < 0.05) by IFB than those with good body condition (15.9%). In 91.4% of animals which had IFB, all the materials were located in the rumen. This study showed that presence of IFB is a common problem in cattle slaughtered at Morogoro Municipal Slaughterhouse and may significantly cause poor production and mortality in affected animals. Therefore, appropriate solid waste disposal should be implemented.

Occurrences of Indigestible Foreign Bodies in Cattle Slaughtered at Morogoro Municipal Slaughterhouse, Tanzania

PubMed Central

Bwatota, S. F.

2018-01-01

A cross-sectional study was conducted to determine the occurrence of indigestible foreign bodies (IFB) in cattle slaughtered at Morogoro Municipal Slaughterhouse, Tanzania. A total of 387 slaughter cattle were examined for presence of IFB. Out of 387 examined cattle, 93 (24.03%) had IFB in their forestomachs. The observed IFB were plastic bags, fruit seeds, clothing materials, ropes, hairballs, leather materials, stones, metallic nails, and wire. Plastic bags were the most frequently (50.5%) observed IFB followed by fruit seeds (18.3%). A significantly (p < 0.05) high proportion of old animals (31.7%) had IFB compared to the young animals (21.2%). Similarly, the frequency of occurrence of IFB was significantly high (p < 0.05) in crossbred dairy cattle (42.3%) compared to local breeds (22.7%). Cattle that appeared with poor body condition (37.8%) were found to be more affected (p < 0.05) by IFB than those with good body condition (15.9%). In 91.4% of animals which had IFB, all the materials were located in the rumen. This study showed that presence of IFB is a common problem in cattle slaughtered at Morogoro Municipal Slaughterhouse and may significantly cause poor production and mortality in affected animals. Therefore, appropriate solid waste disposal should be implemented. PMID:29682585

Surface hardness of different restorative materials after long-term immersion in sports and energy drinks.

PubMed

Erdemir, Ugur; Yildiz, Esra; Eren, Meltem Mert; Ozel, Sevda

2012-01-01

The purpose of this study was to evaluate the effect of sports and energy drinks on the surface hardness of different restorative materials over a 6-month period. Forty-two disk-shaped specimens were prepared for each of the four restorative materials tested: Compoglass F, Filtek Z250, Filtek Supreme, and Premise. Specimens were immersed for 2 min daily, up to 6 months, in six storage solutions (n=7 per material for each solution): distilled water, Powerade, Gatorade, X-IR, Burn, and Red Bull. Surface hardness was measured at baseline, after 1 week, 1 month, and 6 months. Data were analyzed statistically using repeated measures ANOVA followed by the Bonferroni test for multiple comparisons (α=0.05). Surface hardness of the restorative materials was significantly affected by both immersion solution and immersion period (p<0.001). All tested solutions induced significant reduction in surface hardness of the restorative materials over a 6-month immersion period.

Microbial Keratitis: Could Contact Lens Material Affect Disease Pathogenesis?

PubMed Central

Evans, David J.; Fleiszig, Suzanne M. J.

2012-01-01

Microbial keratitis is a sight-threatening complication associated with contact lenses. The introduction of silicone hydrogel lens materials with increased oxygen transmission to the ocular surface has not significantly altered the incidence of microbial keratitis. These data suggest that alternate, or additional, predisposing factors involving lens wear must be addressed to reduce or eliminate these infections. The contact lens can provide a surface for microbial growth in situ, and can also influence ocular surface homeostasis through effects on the tear fluid and corneal epithelium. Thus, it is intuitive that future contact lens materials could make a significant contribution to preventing microbial keratitis. Design of the “right” material to prevent microbial keratitis requires understanding the effects of current materials on bacterial virulence in the cornea, and on ocular surface innate defenses. Current knowledge in each of these areas will be presented, with a discussion of future directions needed to understand the influence of lens material on the pathogenesis of microbial keratitis. PMID:23266587

Material identification based on electrostatic sensing technology

NASA Astrophysics Data System (ADS)

Liu, Kai; Chen, Xi; Li, Jingnan

2018-04-01

When the robot travels on the surface of different media, the uncertainty of the medium will seriously affect the autonomous action of the robot. In this paper, the distribution characteristics of multiple electrostatic charges on the surface of materials are detected, so as to improve the accuracy of the existing electrostatic signal material identification methods, which is of great significance to help the robot optimize the control algorithm. In this paper, based on the electrostatic signal material identification method proposed by predecessors, the multi-channel detection circuit is used to obtain the electrostatic charge distribution at different positions of the material surface, the weights are introduced into the eigenvalue matrix, and the weight distribution is optimized by the evolutionary algorithm, which makes the eigenvalue matrix more accurately reflect the surface charge distribution characteristics of the material. The matrix is used as the input of the k-Nearest Neighbor (kNN)classification algorithm to classify the dielectric materials. The experimental results show that the proposed method can significantly improve the recognition rate of the existing electrostatic signal material recognition methods.

The Effect of Different Mixing Methods on Working Time, Setting Time, Dimensional Changes and Film Thickness of Mineral Trioxide Aggregate and Calcium-Enriched Mixture.

PubMed

Shahi, Shahriar; Ghasemi, Negin; Rahimi, Saeed; Yavari, Hamidreza; Janani, Maryam; Mokhtari, Hadi; Bahari, Mahmood; Rabbani, Parastu

2015-01-01

The aim of the present study was to evaluate the effect of different mixing techniques (conventional, amalgamator and ultrasonic mixing) on the physical properties the working time (WT), setting time (ST), dimensional changes (DC) and film thickness (FT)] of calcium-enriched mixture (CEM) cement and mineral trioxide aggregate (MTA). The mentioned physical properties were determined using the ISO 6786:2001 specification. Six samples of each material were prepared for three mixing techniques (totally 36 samples). Data were analyzed using descriptive statistics, two-way ANOVA and Post Hoc Tukey's tests. The level of significance was defined at 0.05. Irrespective of mixing technique, there was no significant difference between the WT and FT of the tested materials. Except for the DC of MTA and the FT of the all materials, other properties were significantly affected with mixing techniques (P<0.05). The ultrasonic technique decreased the ST of MTA and CEM cement and increased the WT of CEM cement (P<0.05). The mixing technique of the materials had no significant effect on the dimensional changes of MTA and the film thickness of both materials.

Scale-dependent effects on wave propagation in magnetically affected single/double-layered compositionally graded nanosize beams

NASA Astrophysics Data System (ADS)

Ebrahimi, Farzad; Barati, Mohammad Reza

2018-04-01

This article deals with the wave propagation analysis of single/double layered functionally graded (FG) size-dependent nanobeams in elastic medium and subjected to a longitudinal magnetic field employing nonlocal elasticity theory. Material properties of nanobeam change gradually according to the sigmoid function. Applying an analytical solution, the acoustical and optical dispersion relations are explored for various wave number, nonlocality parameter, material composition, elastic foundation constants, and magnetic field intensity. It is found that frequency and phase velocity of waves propagating in S-FGM nanobeam are significantly affected by these parameters. Also, presence of cut-off and escape frequencies in wave propagation analysis of embedded S-FGM nanobeams is investigated.

Effect of a self-adhesive coating on the load-bearing capacity of tooth-coloured restorative materials.

PubMed

Bagheri, R; Palamara, Jea; Mese, A; Manton, D J

2017-03-01

The aim of this study was to compare the flexural strength and Vickers hardness of tooth-coloured restorative materials with and without applying a self-adhesive coating for up to 6 months. Specimens were prepared from three resin composites (RC), two resin-modified glass-ionomer cements (RM-GIC) and two conventional glass-ionomer cements (CGIC). All materials were tested both with and without applying G-Coat Plus (GCP). Specimens were conditioned in 37 °C distilled deionized water for 24 h, and 1, 3 and 6 months. The specimens were strength tested using a four-point bend test jig in a universal testing machine. The broken specimen's halves were used for Vickers hardness testing. Representative specimens were examined under an environmental scanning electron microscope. Data analysis showed that regardless of time and materials, generally the surface coating was associated with a significant increase in the flexural strength of the materials. Applying the GCP decreased the hardness of almost all materials significantly (P < 0.05) and effect of time intervals on hardness was material dependent. The load-bearing capacity of the restorative materials was affected by applying self-adhesive coating and ageing. The CGIC had significantly higher hardness but lower flexural strength than the RM-GIC and RC. © 2016 Australian Dental Association.

Berry Curvature and Chiral Plasmons in Massive Dirac Materials

NASA Astrophysics Data System (ADS)

Song, Justin; Rudner, Mark

2015-03-01

In the semiclassical model of carrier dynamics, quasiparticles are described as nearly free electrons with modified characteristics modified characteristics such as effective masses which may differ significantly from those of an electron in vacuum. In addition to being influenced by external electric and magnetic fields, the trajectories of electrons in topological materials are also affected by the presence of an interesting quantum mechanical field - the Berry curvature - which is responsible for a number of anomalous transport phenomena recently observed in Dirac materials including G/hBN, and MoS2. Here we discuss how Berry curvature can affect the collective behavior of electrons in these systems. In particular, we show that the collective electronic excitations in metallic massive Dirac materials can feature a chirality even in the absence of an applied magnetic field. The chirality of these plasmons arises from the Berry curvature of the massive Dirac bands. The corresponding dispersion is split between left- and right-handed modes. We also discuss experimental manifestations.

Effect of cadmium telluride quantum dots on the dielectric and electro-optical properties of ferroelectric liquid crystals.

PubMed

Kumar, A; Biradar, A M

2011-04-01

We present here the dielectric and electro-optical studies of cadmium telluride quantum dots (CdTe QDs) doped ferroelectric liquid crystals (FLCs). It has been observed that the doping of CdTe QDs not only induced a pronounced memory effect but also affected the physical parameters of FLC material (LAHS19). The modifications in the physical parameters and memory effect of LAHS19 are found to depend on the concentration ratio of CdTe QDs. The lower concentration of CdTe QDs (1-3 wt%) enhanced the values of spontaneous polarization and rotational viscosity of LAHS19 material but did not favor the memory effect, whereas a higher concentration of CdTe QDs (>5 wt%) degraded the alignment of LAHS19 material. The doping of ∼5 wt% of CdTe QDs is found to be the most suitable for achieving good memory effect without significantly affecting the material parameters. ©2011 American Physical Society

Resting connectivity between salience nodes predicts recognition memory.

PubMed

Andreano, Joseph M; Touroutoglou, Alexandra; Dickerson, Bradford C; Barrett, Lisa F

2017-06-01

The resting connectivity of the brain's salience network, particularly the ventral subsystem of the salience network, has been previously associated with various measures of affective reactivity. Numerous studies have demonstrated that increased affective arousal leads to enhanced consolidation of memory. This suggests that individuals with greater ventral salience network connectivity will exhibit greater responses to affective experience, leading to a greater enhancement of memory by affect. To test this hypothesis, resting ventral salience connectivity was measured in 41 young adults, who were then exposed to neutral and negative affect inductions during a paired associate memory test. Memory performance for material learned under both negative and neutral induction was tested for correlation with resting connectivity between major ventral salience nodes. The results showed a significant interaction between mood induction (negative vs neutral) and connectivity between ventral anterior insula and pregenual anterior cingulate cortex, indicating that salience node connectivity predicted memory for material encoded under negative, but not neutral induction. These findings suggest that the network state of the perceiver, measured prior to affective experience, meaningfully influences the extent to which affect modulates memory. Implications of these findings for individuals with affective disorder, who show alterations in both connectivity and memory, are considered. © The Author (2017). Published by Oxford University Press.

Hydraulic conductivity of fly ash-sewage sludge mixes for use in landfill cover liners.

PubMed

Herrmann, Inga; Svensson, Malin; Ecke, Holger; Kumpiene, Jurate; Maurice, Christian; Andreas, Lale; Lagerkvist, Anders

2009-08-01

Secondary materials could help meeting the increasing demand of landfill cover liner materials. In this study, the effect of compaction energy, water content, ash ratio, freezing, drying and biological activity on the hydraulic conductivity of two fly ash-sewage sludge mixes was investigated using a 2(7-1) fractional factorial design. The aim was to identify the factors that influence hydraulic conductivity, to quantify their effects and to assess how a sufficiently low hydraulic conductivity can be achieved. The factors compaction energy and drying, as well as the factor interactions material x ash ratio and ash ratio x compaction energy affected hydraulic conductivity significantly (alpha=0.05). Freezing on five freeze-thaw cycles did not affect hydraulic conductivity. Water content affected hydraulic conductivity only initially. The hydraulic conductivity data were modelled using multiple linear regression. The derived models were reliable as indicated by R(adjusted)(2) values between 0.75 and 0.86. Independent on the ash ratio and the material, hydraulic conductivity was predicted to be between 1.7 x 10(-11)m s(-1) and 8.9 x 10(-10)m s(-1) if the compaction energy was 2.4 J cm(-3), the ash ratio between 20% and 75% and drying did not occur. Thus, the investigated materials met the limit value for non-hazardous waste landfills of 10(-9)m s(-1).

The effect of clinically relevant thermocycling on the flexural properties of endodontic post materials.

PubMed

Stewardson, Dominic A; Shortall, Adrian C; Marquis, Peter M

2010-05-01

It is suggested that fibre-reinforced composite (FRC) posts have lower elastic moduli than metal posts and this will reduce the incidence of root fracture. However, the mechanical properties may be altered in the oral environment. The aims of this study were to determine the effect on the flexural properties of FRC and metal post materials produced by: (1) a thermocycling regime which was clinically relevant and representative of that which would occur during 1 year in the mouth and (2) storage for 1 year at body temperature. Nine FRC and two metal post material samples were sealed in polythene sleeves and thermocycled between 10 degrees C and 50 degrees C for 10,000 cycles. Additional samples were stored dry at 37 degrees C for 1 year. The flexural strength and moduli were determined by three-point bending and compared with untreated control samples. Thermocycling and storage at 37 degrees C for 1 year decreased the mean flexural modulus of all materials. This was statistically significant for 8 of 11 materials after thermocycling, and 4 of 11 materials after storage at 37 degrees C (p<0.05). Thermocycling and storage at 37 degrees C produced a non-significant increase in yield strength for both metal post materials. Thermocycling significantly increased the flexural strength of Postec while it decreased for the other FRC materials. Storage at 37 degrees C increased the flexural strength of three FRC materials (significantly for Postec) while it was decreased among the other materials. Although some of the changes noticed in flexural properties were statistically significant, it is doubtful that they are of sufficient magnitude to affect clinical performance.

[Research on bond durability among different core materials and zirconia ceramic cemented by self-adhesive resin cements].

PubMed

Xinyu, Luo; Xiangfeng, Meng

2017-02-01

This research estimated shear bond durability of zirconia and different substrates cemented by two self-adhesive resin cements (Clearfil SA Luting and RelyX U100) before and after aging conditioning. Machined zirconia ceramic discs were cemented with four kinds of core material (cobalt-chromium alloy, flowable composite resin core material, packable composite resin, and dentin) with two self-adhesive resin cements (Clearfil SA Luting and RelyX U100). All specimens were divided into eight test groups, and each test group was divided into two subgroups. Each subgroup was subjected to shear test before and after 10 000 thermal cycles. All factors (core materials, cements, and thermal cycle) significantly influenced bond durability of zirconia ceramic (P<0.00 1). After 10 000 thermal cycles, significant decrease was not observed in shear bond strength of cobalt-chromium alloy luted with Clearfil SA Luting (P>0.05); observed shear bond strength was significantly higher than those of other substrates (P<0.05). Significantly higher shear bond strength was noted in Clearfil SA Luting luted with cobalt-chromium alloy, flowable composite resin core material, and packable composite resin than that of RelyX U100 (P<0.05). However, significant difference was not observed in shear bond strength of dentin luted with Clearfil SA Luting and RelyX U100 (P>0.05). Different core materials and self-adhesive resin cements can significantly affect bond durability of zirconia ceramic. 
.

Finite element based micro-mechanics modeling of textile composites

NASA Technical Reports Server (NTRS)

Glaessgen, E. H.; Griffin, O. H., Jr.

1995-01-01

Textile composites have the advantage over laminated composites of a significantly greater damage tolerance and resistance to delamination. Currently, a disadvantage of textile composites is the inability to examine the details of the internal response of these materials under load. Traditional approaches to the study fo textile based composite materials neglect many of the geometric details that affect the performance of the material. The present three dimensional analysis, based on the representative volume element (RVE) of a plain weave, allows prediction of the internal details of displacement, strain, stress, and failure quantities. Through this analysis, the effect of geometric and material parameters on the aforementioned quantities are studied.

Antimicrobial activity and properties of irreversible hydrocolloid impression materials incorporated with silver nanoparticles.

PubMed

Ginjupalli, Kishore; Alla, Rama Krishna; Tellapragada, Chaitanya; Gupta, Lokendra; Upadhya Perampalli, Nagaraja

2016-06-01

Conventional spray and the immersion disinfection of irreversible hydrocolloid impression materials may lead to dimensional changes. The purpose of this in vitro study was to investigate the antimicrobial activity and properties of irreversible hydrocolloid impression materials incorporated with silver nanoparticles. The antimicrobial activity and properties of 2 commercially available irreversible hydrocolloid impression materials were evaluated after incorporating varying concentrations of silver nanoparticles. Antimicrobial activity was determined using the disk diffusion method. The gel strength, permanent deformation, flow, and gelation time were measured according to American Dental Association specification #18. Analysis of variance was used to identify the significant differences within and across the groups (α=.05). Adding silver nanoparticles to irreversible hydrocolloid impression materials resulted in superior antimicrobial activity without adversely affecting their properties. Adding silver nanoparticles to Zelgan significantly increased the gel strength compared with the control group, except at 5 wt%. However, the gel strength of Tropicalgin was unaffected except at 5 wt%. An increase in the permanent deformation was found with the incorporation of silver nanoparticles in both Zelgan and Tropicalgin. The flow of Zelgan increased with the incorporation of silver nanoparticles, whereas a decrease in the flow of Tropicalgin was observed at 1 wt% and 2 wt%. An increase in the gelation time of both Zelgan and Tropicalgin was observed with the incorporation of silver nanoparticles. Based on this in vitro study, silver nanoparticles can be incorporated into irreversible hydrocolloid impression materials as antimicrobial agents without adversely affecting their properties. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Comparison of hardness of three temporary filling materials cured by two light-curing devices.

PubMed

Bodrumlu, E; Koçak, M M; Hazar Bodrumlu, E; Ozcan, S; Koçak, S

2014-01-01

Polymerization ability of light-curing devices can affect the light-cured material hardness. The purpose of the present study was to evaluate and compare the hardness of three temporary filling materials that had been light-cured by either a light emitting diode (LED) or a halogen light-curing unit. The temporary filling materials, First Fill, Voco Clip and Bioplic, were placed in wells in a Teflon plate. The 24 specimens of each material were divided into two groups (N.=12/group) for photo-activation by either of the two light-curing units. The LED or halogen device was applied for 40s to the top surface of each specimen. A Knoop hardness test was performed on the top and bottom surface of each specimen, with five measurements per specimen. The highest hardness values for both the LED and halogen treated groups were observed for First Fill and the lowest values were for Voco Clip in top and bottom surfaces. The hardness obtained for the three materials with the halogen unit were significantly higher than the values obtained with the LED unit in both surfaces (P<0.05). First Fill light-cured temporary material exhibited the highest hardness values on the top and bottom surfaces than Voco Clip and Bioplic temporary materials. The hardness of light-cured temporary filling materials can be affected by the type of light-curing unit.

Harvesting Productionin Uneven-Aged Loblolly-Shortleaf Pine Stands:The Crossett Farm Forestry Forties

Treesearch

R. Kluender; B. Stokes; S. Woodfin

1992-01-01

Twostands managed using uneven-aged techniques werehar- vested aspar-t of a5-year entry schedule. Felling and skidding productivity varied significantly with average stem diameter and volume and was affected by diameter distribution of the removed material.

[The influence of polymerization time on physicochemical properties of the acrylic resin Vertex RS].

PubMed

Fraczak, Bogumiła; Sobolewska, Ewa; Ey-Chmielewska, Halina; Skowronek, Maria; Błazewicz, Stanisław

2009-01-01

A good denture can only be produced through proper actions during the clinical and laboratory stages of the production process. The aim of this study was to determine if a change in polymerization time affects the physicochemical properties of polymethacrylate material used for dentures. We examined the acrylic resin Vertex R.S. polymerized for 15, 25, 40, or 60 minutes. Palapress Vario was taken as reference material. Static bending, microhardness, surface wettability, and susceptibility to abrasion were determined. The microhardness test showed that most of the samples had similar Vickers hardness (VS) values, except for the sample polymerized for 25 min. which demonstrated a significantly higher value. Grindability was affected by a change in polymerization time. Mass loss was greatest for samples polymerized for 15, 25, and 60 min. and smallest for Vertex 40 and Palapress Vario. We also observed differences in the wetting angle. Vertex 40 and 60 had a relatively low wetting angle signifying that longer polymerization time results in lower hydrophobicity of the material. The present study has demonstrated that polymerization time has a significant effect on the hardness and some mechanical properties of the acrylic resin.

Effect of high fluence neutron irradiation on transport properties of thermoelectrics

NASA Astrophysics Data System (ADS)

Wang, H.; Leonard, K. J.

2017-07-01

Thermoelectric materials were subjected to high fluence neutron irradiation in order to understand the effect of radiation damage on transport properties. This study is relevant to the NASA Radioisotope Thermoelectric Generator (RTG) program in which thermoelectric elements are exposed to radiation over a long period of time in space missions. Selected n-type and p-type bismuth telluride materials were irradiated at the High Flux Isotope Reactor with a neutron fluence of 1.3 × 1018 n/cm2 (E > 0.1 MeV). The increase in the Seebeck coefficient in the n-type material was partially off-set by an increase in electrical resistivity, making the power factor higher at lower temperatures. For the p-type materials, although the Seebeck coefficient was not affected by irradiation, electrical resistivity decreased slightly. The figure of merit, zT, showed a clear drop in the 300-400 K range for the p-type material and an increase for the n-type material. Considering that the p-type and n-type materials are connected in series in a module, the overall irradiation damages at the device level were limited. These results, at neutron fluences exceeding a typical space mission, are significant to ensure that the radiation damage to thermoelectrics does not affect the performance of RTGs.

Thermal Effects Modeling Developed for Smart Structures

NASA Technical Reports Server (NTRS)

Lee, Ho-Jun

1998-01-01

Applying smart materials in aeropropulsion systems may improve the performance of aircraft engines through a variety of vibration, noise, and shape-control applications. To facilitate the experimental characterization of these smart structures, researchers have been focusing on developing analytical models to account for the coupled mechanical, electrical, and thermal response of these materials. One focus of current research efforts has been directed toward incorporating a comprehensive thermal analysis modeling capability. Typically, temperature affects the behavior of smart materials by three distinct mechanisms: Induction of thermal strains because of coefficient of thermal expansion mismatch 1. Pyroelectric effects on the piezoelectric elements; 2. Temperature-dependent changes in material properties; and 3. Previous analytical models only investigated the first two thermal effects mechanisms. However, since the material properties of piezoelectric materials generally vary greatly with temperature (see the graph), incorporating temperature-dependent material properties will significantly affect the structural deflections, sensory voltages, and stresses. Thus, the current analytical model captures thermal effects arising from all three mechanisms through thermopiezoelectric constitutive equations. These constitutive equations were incorporated into a layerwise laminate theory with the inherent capability to model both the active and sensory response of smart structures in thermal environments. Corresponding finite element equations were formulated and implemented for both the beam and plate elements to provide a comprehensive thermal effects modeling capability.

Effects of Chemical Cross-linkers on Caries-affected Dentin Bonding

PubMed Central

Macedo, G.V.; Yamauchi, M.; Bedran-Russo, A.K.

2009-01-01

The achievement of a strong and stable bond between composite resin and dentin remains a challenge in restorative dentistry. Over the past two decades, dental materials have been substantially improved, with better handling and bonding characteristics. However, little attention has been paid to the contribution of collagen structure/stability to bond strength. We hypothesized that the induction of cross-linking in dentin collagen improves dentin collagen stability and bond strength. This study investigated the effects of glutaraldehyde- and grape seed extract-induced cross-linking on the dentin bond strengths of sound and caries-affected dentin, and on the stability of dentin collagen. Our results demonstrated that the application of chemical cross-linking agents to etched dentin prior to bonding procedures significantly enhanced the dentin bond strengths of caries-affected and sound dentin. Glutaraldehyde and grape seed extract significantly increased dentin collagen stability in sound and caries-affected dentin, likely via distinct mechanisms. PMID:19892915

Influence of material structure on air-borne ultrasonic application in drying.

PubMed

Ozuna, César; Gómez Álvarez-Arenas, Tomás; Riera, Enrique; Cárcel, Juan A; Garcia-Perez, Jose V

2014-05-01

This work aims to contribute to the understanding of how the properties of the material being dried affect air-borne ultrasonic application. To this end, the experimental drying kinetics (40°C and 1m/s) of cassava (Manihot esculenta) and apple (Malus domestica var. Granny Smith) were carried out applying different ultrasonic powers (0, 6, 12, 19, 25 and 31 kW/m(3)). Furthermore, the power ultrasound-assisted drying kinetics of different fruits and vegetables (potato, eggplant, carrot, orange and lemon peel) already reported in previous studies were also analyzed. The structural, textural and acoustic properties of all these products were assessed, and the drying kinetics modeled by means of the diffusion theory. A significant linear correlation (r>0.95) was established between the identified effective diffusivity (DW) and the applied ultrasonic power for the different products. The slope of this relationship (SDUP) was used as an index of the effectiveness of the ultrasonic application; thus the higher the SDUP, the more effective the ultrasound application. SDUP was well correlated (r ⩾ 0.95) with the porosity and hardness. In addition, SDUP was largely affected by the acoustic impedance of the material being dried, showing a similar pattern with the impedance than the transmission coefficient of the acoustic energy on the interface. Thus, soft and open-porous product structures exhibited a better transmission of acoustic energy and were more prone to the mechanical effects of ultrasound. However, materials with a hard and closed-compact structure were less affected by acoustic energy due to the fact that the significant impedance differences between the product and the air cause high energy losses on the interface. Copyright © 2013 Elsevier B.V. All rights reserved.

Does artificial aging affect mechanical properties of CAD/CAM composite materials.

PubMed

Egilmez, Ferhan; Ergun, Gulfem; Cekic-Nagas, Isil; Vallittu, Pekka K; Lassila, Lippo V J

2018-01-01

The purpose of this study was to determine the flexural strength and Weibull characteristics of different CAD/CAM materials after different in vitro aging conditions. The specimens were randomly assigned to one of the six in vitro aging conditions: (1) water storage (37°C, 3 weeks), (2) boiling water (24h), (3) hydrochloric acid exposure (pH: 1.2, 24h), (4) autoclave treatment (134°C, 200kPa, 12h), (5) thermal cycling (5000 times, 5-55°C), (6) cyclic loading (100N, 50,000 cycles). No treatment was applied to the specimens in control group. Three-point bending test was used for the calculation of flexural strength. The reliability of the strength was assessed by Weibull distribution. Surface roughness and topography was examined by coherence scanning interferometry. Evaluated parameters were compared using the Kruskall-Wallis or Mann-Whitney U test. Water storage, autoclave treatment and thermal cycling significantly decreased the flexural strength of all materials (p<0.05), whereas HCl exposure or cyclic loading did not affect the properties (p>0.05). Weibull moduli of Cerasmart™ and Lava™ Ultimate were similar with control. Vita Enamic ® exhibited similar Weibull moduli in all aging groups except the HCl treated group (p>0.05). R a values of Cerasmart™ and Lava™ Ultimate were in the range of 0.053-0.088μm in the aged groups. However R a results of Vita Enamic ® were larger than 0.2μm. Flexural strength of newly developed restorative CAD/CAM materials was significantly decreased by artificial aging. Cyclic loading or HCl exposure does not affect to the flexural strength and structural reliability of Cerasmart™ and Lava™ Ultimate. Copyright © 2017 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Ectoparasitism and the role of green nesting material in the European starling

USGS Publications Warehouse

Fauth, P.T.; Krementz, D.G.; Hines, J.E.

1991-01-01

The use of green nesting material is wide-spread among birds. Recent evidence suggests that birds use secondary chemicals contained in green plants to control ectoparasites. We manipulated green nesting material and ectoparasites of European starlings (Sturnus vulgaris ) to test two hypotheses: (1) ectoparasites adversely affect prefledging survival and morphometrics or postfledging survival, and (2) green nesting material ameliorates the effects of ectoparasites. We recorded fat score, number of scabs, tarsal length, body mass, and hematocrit level on each nestling 17 days after hatching. We also fitted each nestling with unique patagial tags and resighted the starlings for 6-8 weeks after fledging to estimate survival and sighting rates. Nests devoid of green nesting material and dusted with the insecticide, carbaryl, had fewer high ectoparasite infestations, and nestlings had significantly lower scab scores, and significantly higher body masses than nestlings in undusted boxes. However, there was no difference in postfledging survival between birds from carbaryl-treated and undusted nests.

Evaluation of criteria for developing traffic safety materials for Latinos.

PubMed

Streit-Kaplan, Erica L; Miara, Christine; Formica, Scott W; Gallagher, Susan Scavo

2011-03-01

This quantitative study assessed the validity of guidelines that identified four key characteristics of culturally appropriate Spanish-language traffic safety materials: language, translation, formative evaluation, and credible source material. From a sample of 190, the authors randomly selected 12 Spanish-language educational materials for analysis by 15 experts. Hypotheses included that the experts would rate materials with more of the key characteristics as more effective (likely to affect behavioral change) and rate materials originally developed in Spanish and those that utilized formative evaluation (e.g., pilot tests, focus groups) as more culturally appropriate. Although results revealed a weak association between the number of key characteristics in a material and the rating of its effectiveness, reviewers rated materials originally created in Spanish and those utilizing formative evaluation as significantly more culturally appropriate. The findings and methodology demonstrated important implications for developers and evaluators of any health-related materials for Spanish speakers and other population groups.

Extreme ultraviolet patterning of tin-oxo cages

NASA Astrophysics Data System (ADS)

Haitjema, Jarich; Zhang, Yu; Vockenhuber, Michaela; Kazazis, Dimitrios; Ekinci, Yasin; Brouwer, Albert M.

2017-07-01

We report on the extreme ultraviolet (EUV) patterning performance of tin-oxo cages. These cage molecules were already known to function as a negative tone photoresist for EUV radiation, but in this work, we significantly optimized their performance. Our results show that sensitivity and resolution are only meaningful photoresist parameters if the process conditions are optimized. We focus on contrast curves of the materials using large area EUV exposures and patterning of the cages using EUV interference lithography. It is shown that baking steps, such as postexposure baking, can significantly affect both the sensitivity and contrast in the open-frame experiments as well as the patterning experiments. A layer thickness increase reduced the necessary dose to induce a solubility change but decreased the patterning quality. The patterning experiments were affected by minor changes in processing conditions such as an increased rinsing time. In addition, we show that the anions of the cage can influence the sensitivity and quality of the patterning, probably through their effect on physical properties of the materials.

Ignition Prediction of Pressed HMX based on Hotspot Analysis Under Shock Pulse Loading

NASA Astrophysics Data System (ADS)

Kim, Seokpum; Miller, Christopher; Horie, Yasuyuki; Molek, Christopher; Welle, Eric; Zhou, Min

The ignition behavior of pressed HMX under shock pulse loading with a flyer is analyzed using a cohesive finite element method (CFEM) which accounts for large deformation, microcracking, frictional heating, and thermal conduction. The simulations account for the controlled loading of thin-flyer shock experiments with flyer velocities between 1.7 and 4.0 km/s. The study focuses on the computational prediction of ignition threshold using James criterion which involves loading intensity and energy imparted to the material. The predicted thresholds are in good agreement with measurements from shock experiments. In particular, it is found that grain size significantly affects the ignition sensitivity of the materials, with smaller sizes leading to lower energy thresholds required for ignition. In addition, significant stress attenuation is observed in high intensity pulse loading as compared to low intensity pulse loading, which affects density of hotspot distribution. The microstructure-performance relations obtained can be used to design explosives with tailored attributes and safety envelopes.

Meniscal material properties are minimally affected by matrix stabilization using glutaraldehyde and glycation with ribose.

PubMed

Hunter, Shawn A; Noyes, Frank R; Haridas, Balakrishna; Levy, Martin S; Butler, David L

2005-05-01

Knee meniscus replacement holds promise, but current allografts are susceptible to biodegradation. Matrix stabilization with glutaraldehyde, a crosslinking agent used clinically to fabricate cardiovascular bioprostheses, or with glycation, a process of crosslinking collagen with sugars such as ribose, is a potential means of rendering tissue resistant to such degradation. However, stabilization should not significantly alter meniscal material properties, which could disturb normal function in the knee. Our objective was to evaluate the effects of glutaraldehyde- and glycation-induced matrix stabilization on the material properties of porcine meniscus. Normal untreated meniscus specimens were tested in confined compression at one of three applied stresses (0.069, 0.208, 0.347 MPa), subjected to either a glutaraldehyde or glycation stabilization treatment, and then re-tested to measure changes in tissue aggregate modulus, permeability, and compressive strain at equilibrium. Changes in these properties significantly increased with glutaraldehyde concentration and exposure time to ribose. One glutaraldehyde and three glycation treatments did not alter aggregate modulus or compressive strain at equilibrium compared to controls (p > 0.10). However, all treatments increased permeability by at least 108% compared to controls (p < 0.001). This study reveals a dose-dependent relationship between meniscal material properties and certain stabilization conditions and identifies treatments that minimally affect these properties. Further research is necessary to determine whether these treatments prevent enzymatic degradation before and after surgical implantation in the knee.

Prediction of porosity of food materials during drying: Current challenges and directions.

PubMed

Joardder, Mohammad U H; Kumar, C; Karim, M A

2017-07-18

Pore formation in food samples is a common physical phenomenon observed during dehydration processes. The pore evolution during drying significantly affects the physical properties and quality of dried foods. Therefore, it should be taken into consideration when predicting transport processes in the drying sample. Characteristics of pore formation depend on the drying process parameters, product properties and processing time. Understanding the physics of pore formation and evolution during drying will assist in accurately predicting the drying kinetics and quality of food materials. Researchers have been trying to develop mathematical models to describe the pore formation and evolution during drying. In this study, existing porosity models are critically analysed and limitations are identified. Better insight into the factors affecting porosity is provided, and suggestions are proposed to overcome the limitations. These include considerations of process parameters such as glass transition temperature, sample temperature, and variable material properties in the porosity models. Several researchers have proposed models for porosity prediction of food materials during drying. However, these models are either very simplistic or empirical in nature and failed to consider relevant significant factors that influence porosity. In-depth understanding of characteristics of the pore is required for developing a generic model of porosity. A micro-level analysis of pore formation is presented for better understanding, which will help in developing an accurate and generic porosity model.

Behavior of Materials Under Conditions of Thermal Stress

NASA Technical Reports Server (NTRS)

Manson, S S

1954-01-01

A review is presented of available information on the behavior of brittle and ductile materials under conditions of thermal stress and thermal shock. For brittle materials, a simple formula relating physical properties to thermal-shock resistance is derived and used to determine the relative significance of two indices currently in use for rating materials. For ductile materials, thermal-shock resistance depends upon the complex interrelation among several metallurgical variables which seriously affect strength and ductility. These variables are briefly discussed and illustrated from literature sources. The importance of simulating operating conditions in tests for rating materials is especially to be emphasized because of the importance of testing conditions in metallurgy. A number of practical methods that have been used to minimize the deleterious effects of thermal stress and thermal shock are outlined.

The monitoring and fatigue behavior of CFCCs at ambient temperature and 1000{degrees}C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miriyala, N.; Liaw, P.K.; McHargue, C.J.

1997-04-01

Metallographically polished flexure bars of Nicalon/SiC and Nicalon/alumina composites were subjected to monotonic and cycle-fatigue loadings, with loading either parallel or normal to the fabric plies. The fabric orientation did not significantly affect the mechanical behavior of the Nicalon/SiC composite at ambient temperature. However, the mechanical behavior of the Nicalon/alumina composite was significantly affected by the fabric orientation at ambient temperature in air and at 1000{degrees}C in argon atmosphere. In addition, there was a significant degradation in the fatigue performance of the alumina matrix composite at the elevated temperature, owing to creep in the material and degradation in the fibermore » strength.« less

On the impact of the elastic-plastic flow upon the process of destruction of the solenoid in a super strong pulsed magnetic field

NASA Astrophysics Data System (ADS)

Krivosheev, S. I.; Magazinov, S. G.; Alekseev, D. I.

2018-01-01

At interaction of super strong magnetic fields with a solenoid material, a specific mode of the material flow forms. To describe this process, magnetohydrodynamic approximation is traditionally used. The formation of plastic shock-waves in material in a rapidly increasing pressure of 100 GPa/μs, can significantly alter the distribution of the physical parameters in the medium and affect the flow modes. In this paper, an analysis of supporting results of numerical simulations in comparison with available experimental data is presented.

Effects of static tensile load on the thermal expansion of Gr/PI composite material

NASA Technical Reports Server (NTRS)

Farley, G. L.

1981-01-01

The effect of static tensile load on the thermal expansion of Gr/PI composite material was measured for seven different laminate configurations. A computer program was developed which implements laminate theory in a piecewise linear fashion to predict the coupled nonlinear thermomechanical behavior. Static tensile load significantly affected the thermal expansion characteristics of the laminates tested. This effect is attributed to a fiber instability micromechanical behavior of the constituent materials. Analytical results correlated reasonably well with free thermal expansion tests (no load applied to the specimen). However, correlation was poor for tests with an applied load.

Development and testing of novel bisphenol A-free adhesives for lingual fixed retainer bonding.

PubMed

Iliadi, Anna; Eliades, Theodore; Silikas, Nick; Eliades, George

2017-02-01

To comparatively evaluate the properties of two BPA-free experimental adhesives (EXA, EXB) for lingual fixed retainer bonding versus a commercially available reference material (Transbond LR-TLR) based on BPA-compound. The experimental materials were a flowable 60 per cent glass filler-filled UEDMA/TEGDMA flowable composite (EXB) and a 70 per cent glass filler-filled paste composite with PCDMA/UEDMA/TEGDMA co-monomers. The properties tested were degree of conversion (DC%), mechanical properties (Martens hardness-MH, elastic modulus-E IT , elastic index-n IT ), effect of prolonged (6 months) water storage (changes in Vickers microhardness-VHN) and pull-out strength employing a multi-stranded wire. EXB showed the highest DC% (63.6 per cent), followed by EXA (50.5 per cent) and TRL (44.1 per cent), with all means differences being statistically significant (P < 0.05). The statistical rankings of MH (MPa) and E IT (GPa) means were TLR (76.1MPa; 17.3GPa) > EXA (53MPa; 12.9GPa) > EXB (12.9MPa; 6.7GPa), whereas for n IT, EXB (40 per cent) > EXA (34.9 per cent), TLR (33.6 per cent). All materials were affected by prolonged water storage with significant differences among them in VHN. TLR was the most affected material (ΔVHN = -11 per cent), followed by EXA (ΔVHN = -6.8 per cent) and EXB (ΔVHN = -4.2 per cent). No statistically significant differences were found in the pull-out strength testing (24-24.2 N range) and failure mode (70-77 per cent mixed). Considering the differences between the two experimental materials, it may be concluded that the material containing the PCDMA/UEDMA/TEGDMA co-monomers may be used as an alternative to the control. © The Author 2015. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Effects of setting under air pressure on the number of surface pores and irregularities of dental investment materials.

PubMed

Tourah, Anita; Moshaverinia, Alireza; Chee, Winston W

2014-02-01

Surface roughness and irregularities are important properties of dental investment materials that can affect the fit of a restoration. Whether setting under air pressure affects the surface irregularities of gypsum-bonded and phosphate-bonded investment materials is unknown. The purpose of this study was to investigate the effect of air pressure on the pore size and surface irregularities of investment materials immediately after pouring. Three dental investments, 1 gypsum-bonded investment and 2 phosphate-bonded investments, were investigated. They were vacuum mixed according to the manufacturers' recommendations, then poured into a ringless casting system. The prepared specimens were divided into 2 groups: 1 bench setting and the other placed in a pressure pot at 172 kPa. After 45 minutes of setting, the rings were removed and the investments were cut at a right angle to the long axis with a diamond disk. The surfaces of the investments were steam cleaned, dried with an air spray, and observed with a stereomicroscope. A profilometer was used to evaluate the surface roughness (μm) of the castings. The number of surface pores was counted for 8 specimens from each group and the means and standard deviations were reported. Two-way ANOVA was used to compare the data. Specimens that set under atmospheric air pressure had a significantly higher number of pores than specimens that set under increased pressure (P<.05). No statistically significant differences for surface roughness were found (P=.078). Also, no significant difference was observed among the 3 different types of materials tested (P>.05). Specimens set under positive pressure in a pressure chamber presented fewer surface bubbles than specimens set under atmospheric pressure. Positive pressure is effective and, therefore, is recommended for both gypsum-bonded and phosphate-bonded investment materials. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

Surface hardness evaluation of different composite resin materials: influence of sports and energy drinks immersion after a short-term period

PubMed Central

ERDEMİR, Ugur; YİLDİZ, Esra; EREN, Meltem Mert; OZEL, Sevda

2013-01-01

Objectives: This study evaluated the effect of sports and energy drinks on the surface hardness of different composite resin restorative materials over a 1-month period. Material and Methods: A total of 168 specimens: Compoglass F, Filtek Z250, Filtek Supreme, and Premise were prepared using a customized cylindrical metal mould and they were divided into six groups (N=42; n=7 per group). For the control groups, the specimens were stored in distilled water for 24 hours at 37º C and the water was renewed daily. For the experimental groups, the specimens were immersed in 5 mL of one of the following test solutions: Powerade, Gatorade, X-IR, Burn, and Red Bull, for two minutes daily for up to a 1-month test period and all the solutions were refreshed daily. Surface hardness was measured using a Vickers hardness measuring instrument at baseline, after 1-week and 1-month. Data were statistically analyzed using Multivariate repeated measure ANOVA and Bonferroni's multiple comparison tests (α=0.05). Results: Multivariate repeated measures ANOVA revealed that there were statistically significant differences in the hardness of the restorative materials in different immersion times (p<0.001) in different solutions (p<0.001). The effect of different solutions on the surface hardness values of the restorative materials was tested using Bonferroni's multiple comparison tests, and it was observed that specimens stored in distilled water demonstrated statistically significant lower mean surface hardness reductions when compared to the specimens immersed in sports and energy drinks after a 1-month evaluation period (p<0.001). The compomer was the most affected by an acidic environment, whereas the composite resin materials were the least affected materials. Conclusions: The effect of sports and energy drinks on the surface hardness of a restorative material depends on the duration of exposure time, and the composition of the material. PMID:23739850

Radon Release and Its Simulated Effect on Radiation Doses.

PubMed

Orabi, Momen

2017-03-01

One of the main factors that affect the uncertainty in calculating the gamma-radiation absorbed dose rate inside a room is the variation in the degree of secular equilibrium of the considered radioactive series. A component of this factor, considered in this paper, is the release of radon (Rn) from building materials to the living space of the room. This release takes place through different steps. These steps are represented and mathematically formulated. The diffusion of radon inside the material is described by Fick's second law. Some of the factors affecting the radon release rate (e.g. covering walls, moisture, structure of the building materials, etc.) are discussed. This scheme is used to study the impact of radon release on the gamma-radiation absorbed dose rate inside a room. The investigation is carried out by exploiting the MCNP simulation software. Different building materials are considered with different radon release rates. Special care is given to Rn due to its relatively higher half-life and higher indoor concentration than the other radon isotopes. The results of the presented model show that the radon release is of a significant impact in some building materials.

Finite Element Analysis of Interaction of Laser Beam with Material in Laser Metal Powder Bed Fusion Process.

PubMed

Fu, Guang; Zhang, David Z; He, Allen N; Mao, Zhongfa; Zhang, Kaifei

2018-05-10

A deep understanding of the laser-material interaction mechanism, characterized by laser absorption, is very important in simulating the laser metal powder bed fusion (PBF) process. This is because the laser absorption of material affects the temperature distribution, which influences the thermal stress development and the final quality of parts. In this paper, a three-dimensional finite element analysis model of heat transfer taking into account the effect of material state and phase changes on laser absorption is presented to gain insight into the absorption mechanism, and the evolution of instantaneous absorptance in the laser metal PBF process. The results showed that the instantaneous absorptance was significantly affected by the time of laser radiation, as well as process parameters, such as hatch space, scanning velocity, and laser power, which were consistent with the experiment-based findings. The applicability of this model to temperature simulation was demonstrated by a comparative study, wherein the peak temperature in fusion process was simulated in two scenarios, with and without considering the effect of material state and phase changes on laser absorption, and the simulated results in the two scenarios were then compared with experimental data respectively.

[The application of inductively coupled plasma atomic emission spectrometry/mass spectrometry to the analysis of advanced ceramic materials].

PubMed

Wang, Zheng; Wang, Shi-Wei; Qiu, De-Ren; Yang, Peng-Yuan

2009-10-01

Advanced ceramics have been applied to various important fields such as information science, aeronautics and astronautics, and life sciences. However, the optics and electric properties of ceramics are significantly affected by the micro and trace impurities existing in the material even at very low concentration level. Thus, the accurate determination of impurities is important for materials preparation and performance. Methodology of the analysis of advanced ceramic materials using ICP-AES/MS was reviewed in the present paper for the past decade. Various techniques of sample introduction, especially advances in the authors' recent work, are described in detail. The developing trend is also presented. Sixty references are cited.

Modeling the Relationship Between Porosity and Permeability During Oxidation of Ablative Materials

NASA Technical Reports Server (NTRS)

Thornton, John M.; Panerai, Francesco; Ferguson, Joseph C.; Borner, Arnaud; Mansour, Nagi N.

2017-01-01

The ablative materials used in thermal protection systems (TPS) undergo oxidation during atmospheric entry which leads to an in-depth change in both permeability and porosity. These properties have a significant affect on heat transfer in a TPS during entry. X-ray micro-tomography has provided 3D images capturing the micro-structure of TPS materials. In this study, we use micro-tomography based simulations to create high-fidelity models relating permeability to porosity during oxidation of FiberForm, the carbon fiber preform of the Phenolic Impregnated Carbon Ablator (PICA) often used as a TPS material. The goal of this study is to inform full-scale models and reduce uncertainty in TPS modeling.

Determining the Critical Dose Threshold of Electron-Induced Electron Yield for Minimally Charged Highly Insulating Materials

NASA Astrophysics Data System (ADS)

Hoffmann, Ryan; Dennison, J. R.; Abbott, Jonathan

2006-03-01

When incident energetic electrons interact with a material, they excite electrons within the material to escape energies. The electron emission is quantified as the ratio of emitted electrons to incident particle flux, termed electron yield. Measuring the electron yield of insulators is difficult due to dynamic surface charge accumulation which directly affects landing energies and the potential barrier that emitted electrons must overcome. Our recent measurements of highly insulating materials have demonstrated significant changes in total yield curves and yield decay curves for very small electron doses equivalent to a trapped charge density of <10^10 electrons /cm^3. The Chung-Everhart theory provides a basic model for the behavior of the electron emission spectra which we relate to yield decay curves as charge is allowed to accumulate. Yield measurements as a function of dose for polyimide (Kapton^TM) and microcrystalline SiO2 will be presented. We use our data and model to address the question of whether there is a minimal dose threshold at which the accumulated charge no longer affects the yield.

Influence of size-fractioning techniques on concentrations of selected trace metals in bottom materials from two streams in northeastern Ohio

USGS Publications Warehouse

Koltun, G.F.; Helsel, Dennis R.

1986-01-01

Identical stream-bottom material samples, when fractioned to the same size by different techniques, may contain significantly different trace-metal concentrations. Precision of techniques also may differ, which could affect the ability to discriminate between size-fractioned bottom-material samples having different metal concentrations. Bottom-material samples fractioned to less than 0.020 millimeters by means of three common techniques (air elutriation, sieving, and settling) were analyzed for six trace metals to determine whether the technique used to obtain the desired particle-size fraction affects the ability to discriminate between bottom materials having different trace-metal concentrations. In addition, this study attempts to assess whether median trace-metal concentrations in size-fractioned bottom materials of identical origin differ depending on the size-fractioning technique used. Finally, this study evaluates the efficiency of the three size-fractioning techniques in terms of time, expense, and effort involved. Bottom-material samples were collected at two sites in northeastern Ohio: One is located in an undeveloped forested basin, and the other is located in a basin having a mixture of industrial and surface-mining land uses. The sites were selected for their close physical proximity, similar contributing drainage areas, and the likelihood that trace-metal concentrations in the bottom materials would be significantly different. Statistically significant differences in the concentrations of trace metals were detected between bottom-material samples collected at the two sites when the samples had been size-fractioned by means of air elutriation or sieving. Statistical analyses of samples that had been size fractioned by settling in native water were not measurably different in any of the six trace metals analyzed. Results of multiple comparison tests suggest that differences related to size-fractioning technique were evident in median copper, lead, and iron concentrations. Technique-related differences in copper concentrations most likely resulted from contamination of air-elutriated samples by a feed tip on the elutriator apparatus. No technique-related differences were observed in chromium, manganese, or zinc concentrations. Although air elutriation was the most expensive sizefractioning technique investigated, samples fractioned by this technique appeared to provide a superior level of discrimination between metal concentrations present in the bottom materials of the two sites. Sieving was an adequate lower-cost but more laborintensive alternative.

Degradation of strength properties of epoxy resin filled with natural-based particles

NASA Astrophysics Data System (ADS)

Valášek, Petr; Habrová, Karolína; Müller, Miroslav

2018-05-01

Degradation of polymeric materials can be considered as a limiting factor for their use. Mechanical characteristics of epoxy resins are reduced, for example, by the action and changes of temperature or humidity. Degradation also occurs in composite systems where the epoxy resins function as matrices, i.e. in polymer composite materials. If a natural filler is used together with the epoxy resin, we refer to these materials as biocomposites, where also the natural character of the filler material greatly affects the degradation process. The paper focuses on the description of the shear strength of the resin filled with particles prepared from the seeds of dates of Phoenix Dactylifera plant. The degradation was evaluated experimentally in laboratory conditions via the climatic chamber. The experiment describes composites with a particle size of filler 100-200 μm with a concentration of 5 - 10 wt%. As the number of degradation cycles increased, the tensile strength of both the unfilled and the filled epoxy resin decreased. After 5 weeks, the drop was up to 50%. The presence of the particles did not significantly affect the shear strength compared to the non-filled resin. The described way of utilization of the natural-based particles is the possibility of material utilization of secondary natural materials.

Review on fluoride-releasing restorative materials--fluoride release and uptake characteristics, antibacterial activity and influence on caries formation.

PubMed

Wiegand, Annette; Buchalla, Wolfgang; Attin, Thomas

2007-03-01

The purpose of this article was to review the fluoride release and recharge capabilities, and antibacterial properties, of fluoride-releasing dental restoratives, and discuss the current status concerning the prevention or inhibition of caries development and progression. Information from original scientific full papers or reviews listed in PubMed (search term: fluoride release AND (restorative OR glass-ionomer OR compomer OR polyacid-modified composite resin OR composite OR amalgam)), published from 1980 to 2004, was included in the review. Papers dealing with endodontic or orthodontic topics were not taken into consideration. Clinical studies concerning secondary caries development were only included when performed in split-mouth design with an observation period of at least three years. Fluoride-containing dental materials show clear differences in the fluoride release and uptake characteristics. Short- and long-term fluoride releases from restoratives are related to their matrices, setting mechanisms and fluoride content and depend on several environmental conditions. Fluoride-releasing materials may act as a fluoride reservoir and may increase the fluoride level in saliva, plaque and dental hard tissues. However, clinical studies exhibited conflicting data as to whether or not these materials significantly prevent or inhibit secondary caries and affect the growth of caries-associated bacteria compared to non-fluoridated restoratives. Fluoride release and uptake characteristics depend on the matrices, fillers and fluoride content as well as on the setting mechanisms and environmental conditions of the restoratives. Fluoride-releasing materials, predominantly glass-ionomers and compomers, did show cariostatic properties and may affect bacterial metabolism under simulated cariogenic conditions in vitro. However, it is not proven by prospective clinical studies whether the incidence of secondary caries can be significantly reduced by the fluoride release of restorative materials.

40 CFR 63.7886 - What are the general standards I must meet for my affected remediation material management units?

Code of Federal Regulations, 2010 CFR

2010-07-01

... meet for my affected remediation material management units? 63.7886 Section 63.7886 Protection of... Hazardous Air Pollutants: Site Remediation General Standards § 63.7886 What are the general standards I must meet for my affected remediation material management units? (a) For each remediation material...

Delayed photo-activation and addition of thio-urethane: Impact on polymerization kinetics and stress of dual-cured resin cements.

PubMed

Faria-E-Silva, André L; Pfeifer, Carmem S

2017-10-01

1) to determine the moment during the redox polymerization reaction of dual cure cements at which to photo-activate the material in order to reduce the polymerization stress, and 2) to evaluate possible synergistic effects between adding chain transfer agents and delayed photo-activation. The two pastes of an experimental dual-cure material were mixed, and the polymerization kinetics of the redox phase was followed. The moment when the material reached its maximum rate of redox polymerization (MRRP) of cement was determined. The degree of conversion (DC) and maximum rates of polymerization (Rp max ) were assessed for materials where: the photoactivation immediately followed material mixing, at MRRP, 1min before and 1min after MRRP. Thio-urethane (TU) additives were synthesized and added to the cement (20% wt), which was then cured under the same conditions. The polymerization kinetics was evaluated for both cements photo-activated immediately or at MRRP, followed by measurements of polymerization stress, flexural strength (FS) and elastic modulus (EM). Knoop hardness was measured before and after ethanol storage. Photo-activating the cement at or after MRRP reduced the Rp max and the polymerization stress. Addition of TU promoted additional and more significant reduction, while not affecting the Rp max . Greater hardness loss was observed for cements with TU, but the final hardness was similar for all experimental conditions. Addition of TU slightly reduced the EM and did not affect the FS. Delayed photo-activation and addition of TU significantly reduce the polymerization stress of dual-cured cements. Copyright © 2017 Elsevier Ltd. All rights reserved.

Happiness in action: the impact of positive affect on the time of the conscious intention to act

PubMed Central

Rigoni, Davide; Demanet, Jelle; Sartori, Giuseppe

2015-01-01

The temporal relationship between our conscious intentions to act and the action itself has been widely investigated. Previous research consistently shows that the motor intention enters awareness a few 100 ms before movement onset. As research in other domains has shown that most behavior is affected by the emotional state people are in, it is remarkable that the role of emotional states on intention awareness has never been investigated. Here we tested the hypothesis that positive and negative affects have opposite effects on the temporal relationship between the conscious intention to act and the action itself. A mood induction procedure that combined guided imagery and music listening was employed to induce positive, negative, or neutral affective states. After each mood induction session, participants were asked to execute voluntary self-paced movements and to report when they formed the intention to act. Exposure to pleasant material, as compared to exposure to unpleasant material, enhanced positive affect and dampened negative affect. Importantly, in the positive affect condition participants reported their intention to act earlier in time with respect to action onset, as compared to when they were in the negative or in the neutral affect conditions. Conversely the reported time of the intention to act when participants experienced negative affect did not differ significantly from the neutral condition. These findings suggest that the temporal relationship between the conscious intention to act and the action itself is malleable to changes in affective states and may indicate that positive affect enhances intentional awareness. PMID:26388812

Lunar Surface Propagation Modeling and Effects on Communications

NASA Technical Reports Server (NTRS)

Hwu, Shian U.; Upanavage, Matthew; Sham, Catherine C.

2008-01-01

This paper analyzes the lunar terrain effects on the signal propagation of the planned NASA lunar wireless communication and sensor systems. It is observed that the propagation characteristics are significantly affected by the presence of the lunar terrain. The obtained results indicate that the terrain geometry, antenna location, and lunar surface material are important factors determining the propagation characteristics of the lunar wireless communication systems. The path loss can be much more severe than the free space propagation and is greatly affected by the antenna height, operating frequency, and surface material. The analysis results from this paper are important for the lunar communication link margin analysis in determining the limits on the reliable communication range and radio frequency coverage performance at planned lunar base worksites. Key Words lunar, multipath, path loss, propagation, wireless.

Effect of high fluence neutron irradiation on transport properties of thermoelectrics

DOE PAGES

Wang, H.; Leonard, K. J.

2017-07-25

Thermoelectric materials were subjected to high fluence neutron irradiation in order to understand the effect of radiation damage on transport properties. This paper is relevant to the NASA Radioisotope Thermoelectric Generator (RTG) program in which thermoelectric elements are exposed to radiation over a long period of time in space missions. Selected n-type and p-type bismuth telluride materials were irradiated at the High Flux Isotope Reactor with a neutron fluence of 1.3 × 10 18 n/cm 2 (E > 0.1 MeV). The increase in the Seebeck coefficient in the n-type material was partially off-set by an increase in electrical resistivity, makingmore » the power factor higher at lower temperatures. For the p-type materials, although the Seebeck coefficient was not affected by irradiation, electrical resistivity decreased slightly. The figure of merit, zT, showed a clear drop in the 300–400 K range for the p-type material and an increase for the n-type material. Considering that the p-type and n-type materials are connected in series in a module, the overall irradiation damages at the device level were limited. Finally, these results, at neutron fluences exceeding a typical space mission, are significant to ensure that the radiation damage to thermoelectrics does not affect the performance of RTGs.« less

Effect of high fluence neutron irradiation on transport properties of thermoelectrics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, H.; Leonard, K. J.

Thermoelectric materials were subjected to high fluence neutron irradiation in order to understand the effect of radiation damage on transport properties. This paper is relevant to the NASA Radioisotope Thermoelectric Generator (RTG) program in which thermoelectric elements are exposed to radiation over a long period of time in space missions. Selected n-type and p-type bismuth telluride materials were irradiated at the High Flux Isotope Reactor with a neutron fluence of 1.3 × 10 18 n/cm 2 (E > 0.1 MeV). The increase in the Seebeck coefficient in the n-type material was partially off-set by an increase in electrical resistivity, makingmore » the power factor higher at lower temperatures. For the p-type materials, although the Seebeck coefficient was not affected by irradiation, electrical resistivity decreased slightly. The figure of merit, zT, showed a clear drop in the 300–400 K range for the p-type material and an increase for the n-type material. Considering that the p-type and n-type materials are connected in series in a module, the overall irradiation damages at the device level were limited. Finally, these results, at neutron fluences exceeding a typical space mission, are significant to ensure that the radiation damage to thermoelectrics does not affect the performance of RTGs.« less

Controlling vector-borne disease and adapting to climate change with novel research on disease forecasting to target new vector control materials and technologies

USDA-ARS?s Scientific Manuscript database

Population growth, frontier agricultural expansion, and urbanization transform the landscape and the surrounding ecosystem, affecting climate and interactions between animals and humans, and significantly influencing the transmission dynamics and geographic distribution of malaria, dengue and other ...

Grain neighbour effects on twin transmission in hexagonal close-packed materials

NASA Astrophysics Data System (ADS)

Arul Kumar, M.; Beyerlein, I. J.; McCabe, R. J.; Tomé, C. N.

2016-12-01

Materials with a hexagonal close-packed (hcp) crystal structure such as Mg, Ti and Zr are being used in the transportation, aerospace and nuclear industry, respectively. Material strength and formability are critical qualities for shaping these materials into parts and a pervasive deformation mechanism that significantly affects their formability is deformation twinning. The interaction between grain boundaries and twins has an important influence on the deformation behaviour and fracture of hcp metals. Here, statistical analysis of large data sets reveals that whether twins transmit across grain boundaries depends not only on crystallography but also strongly on the anisotropy in crystallographic slip. We show that increases in crystal plastic anisotropy enhance the probability of twin transmission by comparing the relative ease of twin transmission in hcp materials such as Mg, Zr and Ti.

Grain neighbour effects on twin transmission in hexagonal close-packed materials.

PubMed

Arul Kumar, M; Beyerlein, I J; McCabe, R J; Tomé, C N

2016-12-19

Materials with a hexagonal close-packed (hcp) crystal structure such as Mg, Ti and Zr are being used in the transportation, aerospace and nuclear industry, respectively. Material strength and formability are critical qualities for shaping these materials into parts and a pervasive deformation mechanism that significantly affects their formability is deformation twinning. The interaction between grain boundaries and twins has an important influence on the deformation behaviour and fracture of hcp metals. Here, statistical analysis of large data sets reveals that whether twins transmit across grain boundaries depends not only on crystallography but also strongly on the anisotropy in crystallographic slip. We show that increases in crystal plastic anisotropy enhance the probability of twin transmission by comparing the relative ease of twin transmission in hcp materials such as Mg, Zr and Ti.

[Accident with biological material at the prehospital mobile care: reality for health and non-healthcare workers].

PubMed

Tipple, Anaclara Ferreira Veiga; Silva, Elisangelo Aparecido Costa; Teles, Sheila Araújo; Mendonça, Katiane Martins; Souza, Adenícia Custódia Silva E; Melo, Dulcelene Sousa

2013-01-01

Analytical transversal study that was conducted with the objectives of identifying the prevalence and characterizing the accidents with biological material among professionals in pre-hospital service (PHS) and comparing the risk behaviors adopted by healthcare and non-healthcare groups that can affect the occurrence and seriousness of such accidents. Data were obtained by questionnaire applied to all PHS workers in Goiânia-GO. The study revealed a high prevalence of accidents involving biological material which, although higher for the healthcare group, also affected the non-healthcare group. There were significant (p < 0.05) risk behaviors for these accidents in both groups: not using gloves, masks or eye protectors; inappropriate disposal of sharps; inadequate dress; re-capping of needles; and a lack of immunization against hepatitis B. The results underscore the importance of both groups in adhering to preventive measures, and further point to the need to structure and implement vigilance and control system for this type of accident.

Cellulose, hemicelluloses, lignin and ash content of some organic materials and their suitability for use as paper pulp supplements.

PubMed

Ververis, C; Georghiou, K; Danielidis, D; Hatzinikolaou, D G; Santas, P; Santas, R; Corleti, V

2007-01-01

Freshwater algal biomass and orange and lemon peels were assessed as tissue paper pulp supplements. Cellulose and hemicellulose contents of algal biomass were 7.1% and 16.3%, respectively, whereas for citrus peels cellulose content ranged from 12.7% to 13.6% and hemicellulose from 5.3% to 6.1%. For all materials, lignin and ash content was 2% or lower, rendering them suitable for use as paper pulp supplements. The addition of algal biomass to paper pulp increased its mechanical strength significantly. However, brightness was adversely affected by chlorophyll. The addition of citrus peels in paper pulp had no effect on breaking length, increased bursting strength and decreased tearing resistance. Brightness was negatively affected at proportions of 10%, because citrus peel particles behave as coloured pigments. The cost of both materials is about 45% lower than that of conventional pulp, resulting in a 0.9-4.5% reduction in final paper price upon their addition to the pulp.

Relationship between bacterial diversity and environmental parameters during composting of different raw materials.

PubMed

Wang, Xueqin; Cui, Hongyang; Shi, Jianhong; Zhao, Xinyu; Zhao, Yue; Wei, Zimin

2015-12-01

The aim of this study was to compare the bacterial structure of seven different composts. The primary environmental factors affecting bacterial species were identified, and a strategy to enhance the abundance of uncultured bacteria through controlling relevant environmental parameters was proposed. The results showed that the physical-chemical parameters of each different pile changed in its own manner during composting, which affected the structure and succession of bacteria in different ways. DGGE profiles showed that there were 10 prominent species during composting. Among them, four species existed in all compost types, two species existed in several piles and four species were detected in a single material. Redundancy analysis results showed that bacterial species compositions were significantly influenced by C/N and moisture (p<0.05). The optimal range of C/N was 14-27. Based on these results, the primary environmental factors affecting a certain species were further identified as a potential control of bacterial diversity. Copyright © 2015 Elsevier Ltd. All rights reserved.

Behaviour of tunnel lining material in road tunnel fire

NASA Astrophysics Data System (ADS)

Tomar, M.; Khurana, S.; Singh, R.

2018-04-01

The worldwide road tunnel linings are protected against possible fire scenarios to safeguard the structure and assist in occupant evacuation. There are various choices of active and passive protection available, passive protections includes calcium silicate boards, polypropylene fibers, vermiculite cement based sprays, and other intumescent materials. Tunnel fire is a complex phenomenon and researchers in the past has highlighted that there are various factors which affect the tunnel fires. The effect of passive protection techniques on tunnel fire is not well understood, especially for the insulation boards. It’s been understood from past research that for a heavy good vehicular (HGV) fire in the tunnel, the heat feedback effect is significant. Insulation boards may also affect the tunnel fires by altering the heat feedback effect in vehicular tunnels and hence this can affect the overall heat release rates and temperature profile inside a tunnel. This study focuses on studying the role of insulation boards in tunnel fires and evaluating its effect on overall heat release rate and tunnel temperatures.

Characterisation of historic plastics using terahertz time-domain spectroscopy and pulsed imaging.

PubMed

Pastorelli, Gianluca; Trafela, Tanja; Taday, Phillip F; Portieri, Alessia; Lowe, David; Fukunaga, Kaori; Strlič, Matija

2012-05-01

Terahertz (THz) time-domain spectroscopy and 3D THz pulsed imaging have been explored with regard to polymer materials, both commodity and historic polymers. A systematic spectroscopic study of a wide range of different polymer materials showed significant differences in their spectra. Polyolefins and polystyrenes generally exhibit lower absorption than other examined polymers, various cellulose derivates, poly(vinyl chloride), poly(methyl methacrylate), polyamide, hard rubber and phenol formaldehyde resin, the last of these exhibiting the most intense absorption over the entire range, 0.15-4.2 THz. It was also examined how the presence of plasticisers in poly(vinyl chloride), the presence of fillers in polypropylene, and the degree of branching in polyethylene and polystyrene affect the spectra; inorganic fillers in polypropylene affected the absorption most. With 3D THz pulsed imaging, features in polymer objects were explored, appearing either as integral parts of the material (coatings and pores in foams) or as a consequence of physical deterioration (cracks, delamination). All of these features of various complexities can be successfully imaged in 3D. Terahertz technology is thus shown to have significant potential for both chemical and structural characterisation of polymers, which will be of interest to heritage science, but also to the polymer industry and development of analytical technologies in general.

Early detection of materials degradation

NASA Astrophysics Data System (ADS)

Meyendorf, Norbert

2017-02-01

Lightweight components for transportation and aerospace applications are designed for an estimated lifecycle, taking expected mechanical and environmental loads into account. The main reason for catastrophic failure of components within the expected lifecycle are material inhomogeneities, like pores and inclusions as origin for fatigue cracks, that have not been detected by NDE. However, material degradation by designed or unexpected loading conditions or environmental impacts can accelerate the crack initiation or growth. Conventional NDE methods are usually able to detect cracks that are formed at the end of the degradation process, but methods for early detection of fatigue, creep, and corrosion are still a matter of research. For conventional materials ultrasonic, electromagnetic, or thermographic methods have been demonstrated as promising. Other approaches are focused to surface damage by using optical methods or characterization of the residual surface stresses that can significantly affect the creation of fatigue cracks. For conventional metallic materials, material models for nucleation and propagation of damage have been successfully applied for several years. Material microstructure/property relations are well established and the effect of loading conditions on the component life can be simulated. For advanced materials, for example carbon matrix composites or ceramic matrix composites, the processes of nucleation and propagation of damage is still not fully understood. For these materials NDE methods can not only be used for the periodic inspections, but can significantly contribute to the material scientific knowledge to understand and model the behavior of composite materials.

Effect of repair resin type and surface treatment on the repair strength of polyamide denture base resin.

PubMed

Gundogdu, Mustafa; Yanikoglu, Nuran; Bayindir, Funda; Ciftci, Hilal

2015-01-01

The purpose of the present study was to evaluate the effects of different repair resins and surface treatments on the repair strength of a polyamide denture base material. Polyamide resin specimens were prepared and divided into nine groups according to the surface treatments and repair materials. The flexural strengths were measured with a 3-point bending test. Data were analyzed with a 2-way analysis of variance, and the post-hoc Tukey test (α=0.05). The effects of the surface treatments on the surface of the polyamide resin were examined using scanning electron microscopy. The repair resins and surface treatments significantly affected the repair strength of the polyamide denture base material (p<0.05); however, no significant differences were observed interaction between the factors (p>0.05). The flexural strength of the specimens repaired with the polyamide resin was significantly higher than that of those repaired with the heat-polymerized and autopolymerizing acrylic resins.

Chemical speciation of U, Fe, and Pu in melt glass from nuclear weapons testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pacold, J. I.; Lukens, W. W.; Booth, C. H.

Nuclear weapons testing generates large volumes of glassy materials that influence the transport of dispersed actinides in the environment and may carry information on the composition of the detonated device. We determine the oxidation state of U and Fe (which is known to buffer the oxidation state of actinide elements and to affect the redox state of groundwater) in samples of melt glass collected from three U.S. nuclear weapons tests. For selected samples, we also determine the coordination geometry of U and Fe, and we report the oxidation state of Pu from one melt glass sample. We find significant variationsmore » among the melt glass samples and, in particular, find a clear deviation in one sample from the expected buffering effect of Fe(II)/Fe(III) on the oxidation state of uranium. In the first direct measurement of Pu oxidation state in a nuclear test melt glass, we obtain a result consistent with existing literature that proposes Pu is primarily present as Pu(IV) in post-detonation material. In addition, our measurements imply that highly mobile U(VI) may be produced in significant quantities when melt glass is quenched rapidly following a nuclear detonation, though these products may remain immobile in the vitrified matrices. The observed differences in chemical state among the three samples show that redox conditions can vary dramatically across different nuclear test conditions. The local soil composition, associated device materials, and the rate of quenching are all likely to affect the final redox state of the glass. The resulting variations in glass chemistry are significant for understanding and interpreting debris chemistry and the later environmental mobility of dispersed material.« less

Chemical speciation of U, Fe, and Pu in melt glass from nuclear weapons testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pacold, J. I.; Lukens, W. W.; Booth, C. H.

We report that nuclear weapons testing generates large volumes of glassy materials that influence the transport of dispersed actinides in the environment and may carry information on the composition of the detonated device. We determine the oxidation state of U and Fe (which is known to buffer the oxidation state of actinide elements and to affect the redox state of groundwater) in samples of melt glass collected from three U.S. nuclear weapons tests. For selected samples, we also determine the coordination geometry of U and Fe, and we report the oxidation state of Pu from one melt glass sample. Wemore » find significant variations among the melt glass samples and, in particular, find a clear deviation in one sample from the expected buffering effect of Fe(II)/Fe(III) on the oxidation state of uranium. In the first direct measurement of Pu oxidation state in a nuclear test melt glass, we obtain a result consistent with existing literature that proposes Pu is primarily present as Pu(IV) in post-detonation material. In addition, our measurements imply that highly mobile U(VI) may be produced in significant quantities when melt glass is quenched rapidly following a nuclear detonation, though these products may remain immobile in the vitrified matrices. The observed differences in chemical state among the three samples show that redox conditions can vary dramatically across different nuclear test conditions. The local soil composition, associated device materials, and the rate of quenching are all likely to affect the final redox state of the glass. Lastly, the resulting variations in glass chemistry are significant for understanding and interpreting debris chemistry and the later environmental mobility of dispersed material.« less

Chemical speciation of U, Fe, and Pu in melt glass from nuclear weapons testing

DOE PAGES

Pacold, J. I.; Lukens, W. W.; Booth, C. H.; ...

2016-05-18

We report that nuclear weapons testing generates large volumes of glassy materials that influence the transport of dispersed actinides in the environment and may carry information on the composition of the detonated device. We determine the oxidation state of U and Fe (which is known to buffer the oxidation state of actinide elements and to affect the redox state of groundwater) in samples of melt glass collected from three U.S. nuclear weapons tests. For selected samples, we also determine the coordination geometry of U and Fe, and we report the oxidation state of Pu from one melt glass sample. Wemore » find significant variations among the melt glass samples and, in particular, find a clear deviation in one sample from the expected buffering effect of Fe(II)/Fe(III) on the oxidation state of uranium. In the first direct measurement of Pu oxidation state in a nuclear test melt glass, we obtain a result consistent with existing literature that proposes Pu is primarily present as Pu(IV) in post-detonation material. In addition, our measurements imply that highly mobile U(VI) may be produced in significant quantities when melt glass is quenched rapidly following a nuclear detonation, though these products may remain immobile in the vitrified matrices. The observed differences in chemical state among the three samples show that redox conditions can vary dramatically across different nuclear test conditions. The local soil composition, associated device materials, and the rate of quenching are all likely to affect the final redox state of the glass. Lastly, the resulting variations in glass chemistry are significant for understanding and interpreting debris chemistry and the later environmental mobility of dispersed material.« less

Chemical speciation of U, Fe, and Pu in melt glass from nuclear weapons testing

NASA Astrophysics Data System (ADS)

Pacold, J. I.; Lukens, W. W.; Booth, C. H.; Shuh, D. K.; Knight, K. B.; Eppich, G. R.; Holliday, K. S.

2016-05-01

Nuclear weapons testing generates large volumes of glassy materials that influence the transport of dispersed actinides in the environment and may carry information on the composition of the detonated device. We determine the oxidation state of U and Fe (which is known to buffer the oxidation state of actinide elements and to affect the redox state of groundwater) in samples of melt glass collected from three U.S. nuclear weapons tests. For selected samples, we also determine the coordination geometry of U and Fe, and we report the oxidation state of Pu from one melt glass sample. We find significant variations among the melt glass samples and, in particular, find a clear deviation in one sample from the expected buffering effect of Fe(II)/Fe(III) on the oxidation state of uranium. In the first direct measurement of Pu oxidation state in a nuclear test melt glass, we obtain a result consistent with existing literature that proposes Pu is primarily present as Pu(IV) in post-detonation material. In addition, our measurements imply that highly mobile U(VI) may be produced in significant quantities when melt glass is quenched rapidly following a nuclear detonation, though these products may remain immobile in the vitrified matrices. The observed differences in chemical state among the three samples show that redox conditions can vary dramatically across different nuclear test conditions. The local soil composition, associated device materials, and the rate of quenching are all likely to affect the final redox state of the glass. The resulting variations in glass chemistry are significant for understanding and interpreting debris chemistry and the later environmental mobility of dispersed material.

Investigation of Hygro-Thermal Aging on Carbon/Epoxy Materials for Jet Engine Fan Sections

NASA Technical Reports Server (NTRS)

Kohlman, Lee W.; Roberts, Gary D.; Miller, Sandi G.; Pereira, J. Michael

2011-01-01

This poster summarizes 2 years of aging on E862 epoxy and E862 epoxy with triaxial braided T700s carbon fiber composite. Several test methods were used to characterize chemical, physical, and mechanical properties of both the resin and composite materials. The aging cycle that was used included varying temperature and humidity exposure. The goal was to evaluate the environmental effects on a potential jet engine fan section material. Some changes were noted in the resin which resulted in increased brittleness, though this did not significantly affect the tensile and impact test results. A potential decrease in compression strength requires additional investigation.

Effect of artificial accelerated aging on the optical properties and monomeric conversion of composites used after expiration date.

PubMed

Garcia, Lucas da Fonseca Roberti; Mundim, Fabricio Mariano; Pires-de-Souza, Fernanda de Carvalho Panzeri; Puppin Rontani, Regina Maria; Consani, Simonides

2013-01-01

This study sought to evaluate how artificial accelerated aging (AAA) affected color stability (ΔE), opacity (ΔOP), and degree of conversion (DOC) for 3 composite materials (Tetric Ceram, Tetric Ceram HB, and Tetric Flow) used both 180 days before and 180 days after their expiration dates. To evaluate the materials' optical properties, 10 specimens of each composite-5 prior to expiration and 5 after the materials' expiration date-were made in a teflon matrix. After polishing, the specimens were submitted to initial color and opacity readings and submitted to AAA for 384 hours; at that point, new readings were taken to determine ΔE and ΔOP. To evaluate monomeric conversion evaluation, 6 specimens from each composite and expiration date-3 prior to AAA and 3 after-were submitted to DOC analysis. Results of the 2-way ANOVA and Bonferroni's tests (P < 0.05) demonstrated that all composites had ΔE values above the clinically acceptable level (ΔE ≥ 3.3). When expiration dates were compared, only Tetric Flow showed a statistically significant difference (P < 0.05). Regardless of the expiration date, ΔOP values for all composites increased after AAA, but not significantly (P > 0.05). The expired Tetric Flow had the highest DOC values (71.42% ± 4.21) before AAA, significantly different than that of the other composites (P > 0.05). It was concluded that both expiration date and AAA affected the properties of the composites tested.

High-temperature testing of high performance fiber reinforced concrete

NASA Astrophysics Data System (ADS)

Fořt, Jan; Vejmelková, Eva; Pavlíková, Milena; Trník, Anton; Čítek, David; Kolísko, Jiří; Černý, Robert; Pavlík, Zbyšek

2016-06-01

The effect of high-temperature exposure on properties of High Performance Fiber Reinforced Concrete (HPFRC) is researched in the paper. At first, reference measurements are done on HPFRC samples without high-temperature loading. Then, the HPFRC samples are exposed to the temperatures of 200, 400, 600, 800, and 1000 °C. For the temperature loaded samples, measurement of residual mechanical and basic physical properties is done. Linear thermal expansion coefficient as function of temperature is accessed on the basis of measured thermal strain data. Additionally, simultaneous difference scanning calorimetry (DSC) and thermogravimetry (TG) analysis is performed in order to observe and explain material changes at elevated temperature. It is found that the applied high temperature loading significantly increases material porosity due to the physical, chemical and combined damage of material inner structure, and negatively affects also the mechanical strength. Linear thermal expansion coefficient exhibits significant dependence on temperature and changes of material structure. The obtained data will find use as input material parameters for modelling the damage of HPFRC structures exposed to the fire and high temperature action.

Machinability Study on Milling Kenaf Fiber Reinforced Plastic Composite Materials using Design of Experiments

NASA Astrophysics Data System (ADS)

Azmi, H.; Haron, C. H. C.; Ghani, J. A.; Suhaily, M.; Yuzairi, A. R.

2018-04-01

The surface roughness (Ra) and delamination factor (Fd) of a milled kenaf reinforced plastic composite materials are depending on the milling parameters (spindle speed, feed rate and depth of cut). Therefore, a study was carried out to investigate the relationship between the milling parameters and their effects on a kenaf reinforced plastic composite materials. The composite panels were fabricated using vacuum assisted resin transfer moulding (VARTM) method. A full factorial design of experiments was use as an initial step to screen the significance of the parameters on the defects using Analysis of Variance (ANOVA). If the curvature of the collected data shows significant, Response Surface Methodology (RSM) is then applied for obtaining a quadratic modelling equation that has more reliable in expressing the optimization. Thus, the objective of this research is obtaining an optimum setting of milling parameters and modelling equations to minimize the surface roughness (Ra) and delamination factor (Fd) of milled kenaf reinforced plastic composite materials. The spindle speed and feed rate contributed the most in affecting the surface roughness and the delamination factor of the kenaf composite materials.

Biocompatibility and strength properties of nitinol shape memory alloy suture in rabbit tendon.

PubMed

Kujala, Sauli; Pajala, Ari; Kallioinen, Matti; Pramila, Antti; Tuukkanen, Juha; Ryhänen, Jorma

2004-01-01

Nitinol (NiTi) is a promising new tendon suture material with good strength, easy handling and good super-elastic properties. NiTi sutures were implanted for biocompatibility testing into the right medial gastrocnemius tendon in 15 rabbits for 2, 6 and 12 weeks. Additional sutures were implanted in subcutaneous tissue for strength measurements in order to determine the effect of implantation on strength properties of NiTi suture material. Braided polyester sutures (Ethibond) of approximately the same diameter were used as control. Encapsulating membrane formation around the sutures was minimal in the case of both materials. The breaking load of NiTi was significantly greater compared to braided polyester. Implantation did not affect the strength properties of either material.

Can AIDS stigma be reduced to poverty stigma? Exploring Zimbabwean children's representations of poverty and AIDS.

PubMed

Campbell, C; Skovdal, M; Mupambireyi, Z; Madanhire, C; Robertson, L; Nyamukapa, C A; Gregson, S

2012-09-01

We use children's drawings to investigate social stigmatization of AIDS-affected and poverty-affected children by their peers, in the light of suggestions that the stigmatization of AIDS-affected children might derive more from the poverty experienced by these children than from their association with AIDS. A qualitative study, in rural Zimbabwe, used draw-and-write techniques to elicit children's (10-12 years) representations of AIDS-affected children (n= 30) and poverty-affected children (n= 33) in 2009 and 2010 respectively. Representations of children affected by AIDS and by poverty differed significantly. The main problems facing AIDS-affected children were said to be the psychosocial humiliations of AIDS stigma and children's distress about sick relatives. Contrastingly, poverty-affected children were depicted as suffering from physical and material neglect and deprivation. Children affected by AIDS were described as caregivers of parents whom illness prevented from working. This translated into admiration and respect for children's active contribution to household survival. Poverty-affected children were often portrayed as more passive victims of their guardians' inability or unwillingness to work or to prioritize their children's needs, with these children having fewer opportunities to exercise agency in response to their plight. The nature of children's stigmatization of their AIDS-affected peers may often be quite distinct from poverty stigma, in relation to the nature of suffering (primarily psychosocial and material respectively), the opportunities for agency offered by each affliction, and the opportunities each condition offers for affected children to earn the respect of their peers and community. We conclude that the particular nature of AIDS stigma offers greater opportunities for stigma reduction than poverty stigma. © 2011 Blackwell Publishing Ltd.

Can AIDS stigma be reduced to poverty stigma? Exploring Zimbabwean children's representations of poverty and AIDS

PubMed Central

Campbell, C; Skovdal, M; Mupambireyi, Z; Madanhire, C; Robertson, L; Nyamukapa, C A; Gregson, S

2012-01-01

Objective We use children's drawings to investigate social stigmatization of AIDS-affected and poverty-affected children by their peers, in the light of suggestions that the stigmatization of AIDS-affected children might derive more from the poverty experienced by these children than from their association with AIDS. Methods A qualitative study, in rural Zimbabwe, used draw-and-write techniques to elicit children's (10–12 years) representations of AIDS-affected children (n= 30) and poverty-affected children (n= 33) in 2009 and 2010 respectively. Results Representations of children affected by AIDS and by poverty differed significantly. The main problems facing AIDS-affected children were said to be the psychosocial humiliations of AIDS stigma and children's distress about sick relatives. Contrastingly, poverty-affected children were depicted as suffering from physical and material neglect and deprivation. Children affected by AIDS were described as caregivers of parents whom illness prevented from working. This translated into admiration and respect for children's active contribution to household survival. Poverty-affected children were often portrayed as more passive victims of their guardians' inability or unwillingness to work or to prioritize their children's needs, with these children having fewer opportunities to exercise agency in response to their plight. Conclusions The nature of children's stigmatization of their AIDS-affected peers may often be quite distinct from poverty stigma, in relation to the nature of suffering (primarily psychosocial and material respectively), the opportunities for agency offered by each affliction, and the opportunities each condition offers for affected children to earn the respect of their peers and community. We conclude that the particular nature of AIDS stigma offers greater opportunities for stigma reduction than poverty stigma. PMID:21985490

Effects of Electrode Material on the Voltage of a Tree-Based Energy Generator.

PubMed

Hao, Zhibin; Wang, Guozhu; Li, Wenbin; Zhang, Junguo; Kan, Jiangming

2015-01-01

The voltage between a standing tree and its surrounding soil is regarded as an innovative renewable energy source. This source is expected to provide a new power generation system for the low-power electrical equipment used in forestry. However, the voltage is weak, which has caused great difficulty in application. Consequently, the development of a method to increase the voltage is a key issue that must be addressed in this area of applied research. As the front-end component for energy harvesting, a metal electrode has a material effect on the level and stability of the voltage obtained. This study aimed to preliminarily ascertain the rules and mechanisms that underlie the effects of electrode material on voltage. Electrodes of different materials were used to measure the tree-source voltage, and the data were employed in a comparative analysis. The results indicate that the conductivity of the metal electrode significantly affects the contact resistance of the electrode-soil and electrode-trunk contact surfaces, thereby influencing the voltage level. The metal reactivity of the electrode has no significant effect on the voltage. However, passivation of the electrode materials markedly reduces the voltage. Suitable electrode materials are demonstrated and recommended.

The effect of aging on the fracture toughness of esthetic restorative materials.

PubMed

Bagheri, Rafat; Azar, Mohammad R; Tyas, Martin J; Burrow, Michael F

2010-06-01

To compare the fracture toughness (KIc) of tooth-colored restorative materials based on a four-point bending; to assess the effect of distilled water and a resin surface sealant (G-Coat Plus) on the resistance of the materials to fracture. Specimens were prepared from six materials: Quix Fil; Dyract (Dentsply), Freedom (SDI), Fuji VII (GC), Fuji IX (GC); Fuji II LC (GC). Fuji II LC and Fuji IX were tested both with and without applying G-Coat Plus (GC). The specimens were divided into the three groups which were conditioned in distilled water at 37 degrees C for 48 hours, 4 and 8 weeks. The specimens were loaded in a four-point bending test using a universal testing machine. The maximum load to specimen failure was recorded and the fracture toughness calculated. There were significant differences among most of the materials (P < 0.001). Quix Fil had the highest mean KIc value and Fuji VII the lowest. Immersion in distilled water for the resin composite and polyacid-modified resin composites caused a significant decrease in KIc as the time interval increased. For glass-ionomer cements, KIc decreased significantly after 4 weeks, and after 8 weeks immersion slightly increased. G-Coat Plus affected Fuji II LC positively while it had no effect on the Fuji IX.

Comparison of Ductile-to-Brittle Transition Behavior in Two Similar Ferritic Oxide Dispersion Strengthened Alloys.

PubMed

Chao, Jesus; Rementeria, Rosalia; Aranda, Maria; Capdevila, Carlos; Gonzalez-Carrasco, Jose Luis

2016-07-29

The ductile-to-brittle transition (DBT) behavior of two similar Fe-Cr-Al oxide dispersion strengthened (ODS) stainless steels was analyzed following the Cottrell-Petch model. Both alloys were manufactured by mechanical alloying (MA) but by different forming routes. One was manufactured as hot rolled tube, and the other in the form of hot extruded bar. The two hot forming routes considered do not significantly influence the microstructure, but cause differences in the texture and the distribution of oxide particles. These have little influence on tensile properties; however, the DBT temperature and the upper shelf energy (USE) are significantly affected because of delamination orientation with regard to the notch plane. Whereas in hot rolled material the delaminations are parallel to the rolling surface, in the hot extruded material, they are randomly oriented because the material is transversally isotropic.

Comparison of Ductile-to-Brittle Transition Behavior in Two Similar Ferritic Oxide Dispersion Strengthened Alloys

PubMed Central

Chao, Jesus; Rementeria, Rosalia; Aranda, Maria; Capdevila, Carlos; Gonzalez-Carrasco, Jose Luis

2016-01-01

The ductile-to-brittle transition (DBT) behavior of two similar Fe-Cr-Al oxide dispersion strengthened (ODS) stainless steels was analyzed following the Cottrell–Petch model. Both alloys were manufactured by mechanical alloying (MA) but by different forming routes. One was manufactured as hot rolled tube, and the other in the form of hot extruded bar. The two hot forming routes considered do not significantly influence the microstructure, but cause differences in the texture and the distribution of oxide particles. These have little influence on tensile properties; however, the DBT temperature and the upper shelf energy (USE) are significantly affected because of delamination orientation with regard to the notch plane. Whereas in hot rolled material the delaminations are parallel to the rolling surface, in the hot extruded material, they are randomly oriented because the material is transversally isotropic. PMID:28773764

Penalty-Based Finite Element Interface Technology for Analysis of Homogeneous and Composite Structures

NASA Technical Reports Server (NTRS)

Averill, Ronald C.

2002-01-01

An effective and robust interface element technology able to connect independently modeled finite element subdomains has been developed. This method is based on the use of penalty constraints and allows coupling of finite element models whose nodes do not coincide along their common interface. Additionally, the present formulation leads to a computational approach that is very efficient and completely compatible with existing commercial software. A significant effort has been directed toward identifying those model characteristics (element geometric properties, material properties, and loads) that most strongly affect the required penalty parameter, and subsequently to developing simple 'formulae' for automatically calculating the proper penalty parameter for each interface constraint. This task is especially critical in composite materials and structures, where adjacent sub-regions may be composed of significantly different materials or laminates. This approach has been validated by investigating a variety of two-dimensional problems, including composite laminates.

What Affect Student Cognitive Style in the Development of Hypermedia Learning System?

ERIC Educational Resources Information Center

Lee, Catherine Hui Min; Cheng, Yuk Wing; Rai, Shri; Depickere, Arnold

2005-01-01

Recent developments in learning technology such as hypermedia is becoming widespread and offer significant contribution to improve the delivery of learning and teaching materials. A key factor in the development of hypermedia learning system is cognitive style (CS) as it relates to users' information processing habits, representing individual…

Representation of Sports and Recreational Activities in Primary School English Language Coursebooks

ERIC Educational Resources Information Center

Zorba, Mehmet Galip; Arikan, Arda

2012-01-01

Studying coursebooks and instructional materials in terms of their cultural, social and value-based qualities has been a significant aspect of research in language education since what is inherent in coursebooks directly affects users' perspective. In this research study, contents of English language coursebooks used in Turkish senior primary…

History of Nebular Processing Traced by Silicate Stardust in IDPS

NASA Technical Reports Server (NTRS)

Messenger, Scott R.; Keller, L. P.; Nakamura-Messenger, K.

2010-01-01

Chondritic porous interplanetary dust particles (CP-IDPs) may be the best preserved remnants of primordial solar system materials, in part because they were not affected by parent body hydrothermal alteration. Their primitive characteristics include fine grained, unequilibrated, anhydrous mineralogy, enrichment in volatile elements, and abundant molecular cloud material and silicate stardust. However, while the majority of CP-IDP materials likely derived from the Solar System, their formation processes and provenance are poorly constrained. Stardust abundances provide a relative measure of the extent of processing that the Solar System starting materials has undergone in primitive materials. For example, among primitive meteorites silicate stardust abundances vary by over two orders of magnitude (less than 10-200 ppm). This range of abundances is ascribed to varying extents of aqueous processing in the meteorite parent bodies. The higher average silicate stardust abundances among CP-IDPs (greater than 375 ppm) are thus attributable to the lack of aqueous processing of these materials. Yet, silicate stardust abundances in IDPs also vary considerably. While the silicate stardust abundance in IDPs having anomalous N isotopic compositions was reported to be 375 ppm, the abundance in IDPs lacking N anomalies is less than 10 ppm. Furthermore, these values are significantly eclipsed among some IDPs with abundances ranging from 2,000 ppm to 10,000 ppm. Given that CP-IDPs have not been significantly affected by parent body processes, the difference in silicate stardust abundances among these IDPs must reflect varying extents of nebular processing. Here we present recent results of a systematic coordinated mineralogical/isotopic study of large cluster IDPs aimed at (1) characterizing the mineralogy of presolar silicates and (2) delineating the mineralogical and petrographic characteristics of IDPs with differing silicate stardust abundances. One of the goals of this study is to better understand the earliest stages of evolution of the Solar System starting materials.

Analysis of Resin-Dentin Interface Morphology and Bond Strength Evaluation of Core Materials for One Stage Post-Endodontic Restorations

PubMed Central

Bitter, Kerstin; Gläser, Christin; Neumann, Konrad; Blunck, Uwe; Frankenberger, Roland

2014-01-01

Purpose Restoration of endodontically treated teeth using fiber posts in a one-stage procedure gains more popularity and aims to create a secondary monoblock. Data of detailed analyses of so called “post-and-core-systems” with respect to morphological characteristics of the resin-dentin interface in combination with bond strength measurements of fiber posts luted with these materials are scarce. The present study aimed to analyze four different post-and-core-systems with two different adhesive approaches (self-etch and etch-and-rinse). Materials and Methods Human anterior teeth (n = 80) were endodontically treated and post space preparations and post placement were performed using the following systems: Rebilda Post/Rebilda DC/Futurabond DC (Voco) (RB), Luxapost/Luxacore Z/Luxabond Prebond and Luxabond A+B (DMG) (LC), X Post/Core X Flow/XP Bond and Self Cure Activator (Dentsply DeTrey) (CX), FRC Postec/MultiCore Flow/AdheSE DC (Ivoclar Vivadent) (MC). Adhesive systems and core materials of 10 specimens per group were labeled using fluorescent dyes and resin-dentin interfaces were analyzed using Confocal Laser Scanning Microscopy (CLSM). Bond strengths were evaluated using a push-out test. Data were analyzed using repeated measurement ANOVA and following post-hoc test. Results CLSM analyses revealed significant differences between groups with respect to the factors hybrid layer thickness (p<0.0005) and number of resin tags (p = 0.02; ANOVA). Bond strength was significantly affected by core material (p = 0.001), location inside the root canal (p<0.0005) and incorporation of fluorescent dyes (p = 0.036; ANOVA). CX [7.7 (4.4) MPa] demonstrated significantly lower bond strength compared to LC [14.2 (8.7) MPa] and RB [13.3 (3.7) MPa] (p<0.05; Tukey HSD) but did not differ significantly from MC [11.5 (3.5) MPa]. Conclusion It can be concluded that bond strengths inside the root canal were not affected by the adhesive approach of the post-and-core-system. All systems demonstrated homogenous hybrid layer formation and penetration into the dentinal tubules in spite of the complicating conditions for adhesion inside the root canal. PMID:24586248

Method for computing energy release rate using the elastic work factor approach

NASA Astrophysics Data System (ADS)

Rhee, K. Y.; Ernst, H. A.

1992-01-01

The elastic work factor eta(el) concept was applied to composite structures for the calculation of total energy release rate by using a single specimen. Cracked lap shear specimens with four different unidirectional fiber orientation were used to examine the dependence of eta(el) on the material properties. Also, three different thickness ratios (lap/strap) were used to determine how geometric conditions affect eta(el). The eta(el) values were calculated in two different ways: compliance method and crack closure method. The results show that the two methods produce comparable eta(el) values and, while eta(el) is affected significantly by geometric conditions, it is reasonably independent of material properties for the given geometry. The results also showed that the elastic work factor can be used to calculate total energy release rate using a single specimen.

Seeing the Invisible: Educating the Public on Planetary Magnetic Fields and How they Affect Atmospheres

NASA Astrophysics Data System (ADS)

Fillingim, M. O.; Brain, D. A.; Peticolas, L. M.; Schultz, G.; Yan, D.; Guevara, S.; Randol, S.

2009-12-01

Magnetic fields and charged particles are difficult for school children, the general public, and scientists alike to visualize. But studies of planetary magnetospheres and ionospheres have broad implications for planetary evolution, from the deep interior to the ancient climate, that are important to communicate to each of these audiences. This presentation will highlight the visualization materials that we are developing to educate audiences on the magnetic fields of planets and how they affect atmospheres. The visualization materials that we are developing consist of simplified data sets that can be displayed on spherical projection systems and portable 3-D rigid models of planetary magnetic fields.We are developing presentations for science museums and classrooms that relate fundamental information about the Martian magnetic field, how it differs from Earth’s, and why the differences are significant.

Performance of fast-setting impression materials in the reproduction of subgingival tooth surfaces without soft tissue retraction.

PubMed

Rudolph, Heike; Röhl, Andreas; Walter, Michael H; Luthardt, Ralph G; Quaas, Sebastian

2014-01-01

Fast-setting impression materials may be prone to inaccuracies due to accidental divergence from the recommended mixing protocol. This prospective randomized clinical trial aimed to assess three-dimensional (3D) deviations in the reproduction of subgingival tooth surfaces and to determine the effect of either following or purposely diverging from the recommended mixing procedure for a fast-setting addition-curing silicone (AS) and fast-setting polyether (PE). After three impressions each were taken from 96 participants, sawcut gypsum casts were fabricated with a standardized procedure and then optically digitized. Data were assessed with a computer-aided 3D analysis. For AS impressions, multivariate analysis of variance revealed a significant influence of the individual tooth and the degree to which the recommended mixing protocol was violated. For PE impressions, the ambient air temperature and individual tooth showed significant effects, while divergence from the recommended mixing protocol was not of significance. The fast-setting PE material was not affected by changes in the recommended mixing protocol. For the two fast-setting materials examined, no divergences from the recommended mixing protocol of less than 2 minutes led to failures in the reproduction of the subgingival tooth surfaces.

Cutting Modeling of Hybrid CFRP/Ti Composite with Induced Damage Analysis

PubMed Central

Xu, Jinyang; El Mansori, Mohamed

2016-01-01

In hybrid carbon fiber reinforced polymer (CFRP)/Ti machining, the bi-material interface is the weakest region vulnerable to severe damage formation when the tool cutting from one phase to another phase and vice versa. The interface delamination as well as the composite-phase damage is the most serious failure dominating the bi-material machining. In this paper, an original finite element (FE) model was developed to inspect the key mechanisms governing the induced damage formation when cutting this multi-phase material. The hybrid composite model was constructed by establishing three disparate physical constituents, i.e., the Ti phase, the interface, and the CFRP phase. Different constitutive laws and damage criteria were implemented to build up the entire cutting behavior of the bi-material system. The developed orthogonal cutting (OC) model aims to characterize the dynamic mechanisms of interface delamination formation and the affected interface zone (AIZ). Special focus was made on the quantitative analyses of the parametric effects on the interface delamination and composite-phase damage. The numerical results highlighted the pivotal role of AIZ in affecting the formation of interface delamination, and the significant impacts of feed rate and cutting speed on delamination extent and fiber/matrix failure. PMID:28787824

In plastico: laboratory material newness affects growth and reproduction of Daphnia magna reared in 50-ml polypropylene tubes

PubMed Central

Cuhra, Marek; Bøhn, Thomas; Cuhra, Petr

2017-01-01

Plastic laboratory materials are found to affect vital parameters of the waterflea Daphnia magna. The main responsible factor is defined as “newness” of the materials. Juvenile D. magna were raised individually in; a) new laboratory-standard 50 ml polypropylene tubes, and; b) identical tubes which had been washed and aerated for several weeks. Newness had significant effects on growth and fecundity of D. magna. New tubes caused delayed maturation, reduced reproduction and reduced growth when compared to washed and re-used tubes of the same commercial brand. The findings indicate that newness of tubes has inhibiting or toxic effects on D. magna. Often laboratory plastics are intended for single-use due to sterility demands. Newness might be an important confounding factor in research results and should not be disregarded. Disposable plastic utensils may come with a seemingly ignored cost and induce adverse effects in biological test-organisms and systems. The presented findings accentuate continued need for general awareness concerning confounding factors stemming from material laboratory environment. Based on the present findings the authors suggest that plastics intended for use in sensitive research may need to be washed and aerated prior to use. PMID:28425469

Looking into 'London'

NASA Technical Reports Server (NTRS)

2004-01-01

This mosaic image from the microscopic imager on the Mars Exploration Rover Opportunity shows the rock abrasion tool target, 'London.' The image was taken by the Mars Exploration Rover Opportunity on its 149th sol on Mars (June 24, 2004). Scientists 'read' the geology of the image from bottom to top, with the youngest material pictured at the bottom of the image and the oldest material in the layers pictured at the top. Millimeter-scale layers run horizontally across the exposed surface, with two sliced sphere-like objects, or 'blueberries' on the upper left and upper right sides of the impression. This material is similar to the evaporative material found in 'Eagle Crater.' However, the intense review of these layers in Endurance Crater is, in essence, deepening the water story authored by ancient Mars.

In Eagle Crater, the effects of water were traced down a matter of centimeters. Endurance Crater's depth has allowed the tracing of water's telltale marks up to meters. Another process that significantly affects martian terrain is muddying the water story a bit. Although it is clear that the layers in Endurance were affected by water, it is also evident that Aeolian, or wind, processes have contributed to the makeup of the crater.

Effect of storage time on the viscoelastic properties of elastomeric impression materials.

PubMed

Papadogiannis, Dimitris; Lakes, Roderic; Palaghias, George; Papadogiannis, Yiannis

2012-01-01

The aim of this study was to evaluate creep and viscoelastic properties of dental impression materials after different storage times. Six commercially available impression materials (one polyether and five silicones) were tested after being stored for 30 min to 2 weeks under both static and dynamic testing. Shear and Young's moduli, dynamic viscosity, loss tangent and other viscoelastic parameters were calculated. Four of the materials were tested 1 h after setting under creep for three hours and recovery was recorder for 50 h. The tested materials showed differences among them, while storage time had significant influence on their properties. Young's modulus E ranged from 1.81 to 12.99 MPa with the polyether material being the stiffest. All of the materials showed linear viscoelastic behavior exhibiting permanent deformation after 50h of creep recovery. As storage time affects the materials' properties, pouring time should be limited in the first 48 h after impression. Copyright © 2011 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Mechanical Properties of Heat Affected Zone of High Strength Steels

NASA Astrophysics Data System (ADS)

Sefcikova, K.; Brtnik, T.; Dolejs, J.; Keltamaki, K.; Topilla, R.

2015-11-01

High Strength Steels became more popular as a construction material during last decade because of their increased availability and affordability. On the other hand, even though general use of Advanced High Strength Steels (AHSS) is expanding, the wide utilization is limited because of insufficient information about their behaviour in structures. The most widely used technique for joining steels is fusion welding. The welding process has an influence not only on the welded connection but on the area near this connection, the so-called heat affected zone, as well. For that reason it is very important to be able to determine the properties in the heat affected zone (HAZ). This area of investigation is being continuously developed in dependence on significant progress in material production, especially regarding new types of steels available. There are currently several types of AHSS on the world market. Two most widely used processes for AHSS production are Thermo-Mechanically Controlled Processing (TMCP) and Quenching in connection with Tempering. In the presented study, TMCP and QC steels grade S960 were investigated. The study is focused on the changes of strength, ductility, hardness and impact strength in heat affected zone based on the used amount of heat input.

Glove material, reservoir formation, and dose affect glove permeation and subsequent skin penetration.

PubMed

Nielsen, Jesper Bo; Sørensen, Jens Ahm

2012-02-15

Protective gloves are used to reduce dermal exposure when managing chemical exposures at the work place. Different glove materials may offer different degrees of protection. The present study combined the traditional ASTM (American Society for Testing and Materials) model with the Franz diffusion cell to evaluate overall penetration through glove and skin as well as the deposition in the different reservoirs. Benzoic acid was applied on latex or nitrile gloves placed on top of human skin. The amounts of chemical were quantified in the glove material, between glove and skin, within the skin, and in the receptor chamber. Both glove materials reduce total penetration of benzoic acid, but nitrile gloves offer a significantly better protection than latex gloves. This difference was less pronounced at the higher of the two concentrations of benzoic acid applied. Thus, glove types that offer relevant protection at low concentrations does not necessarily give appropriate protection at high concentrations. Significant amounts of benzoic acid could be extracted from the glove materials after exposure. If a chemical is accumulated in the glove material, reuse of single-use gloves should be cautioned. The reuse of gloves is generally not to be recommended without effective decontamination. Copyright © 2011 Elsevier B.V. All rights reserved.

Differences in Tribological Behaviors upon Switching Fixed and Moving Materials of Tribo-pairs including Metal and Polymer.

PubMed

Xu, Aijie; Tian, Pengyi; Wen, Shizhu; Guo, Fei; Hu, Yueqiang; Jia, Wenpeng; Dong, Conglin; Tian, Yu

2017-10-12

The coefficient of friction (COF) between two materials is usually believed to be an intrinsic property of the materials themselves. In this study, metals of stainless steel (304) and brass (H62), and polymers of polypropylene (PP) and polytetrafluoroethylene (PTFE) were tested on a standard ball-on-three-plates test machine. Significantly different tribological behaviors were observed when fixed and moving materials of tribo-pairs (metal/polymer) were switched. As an example, under the same applied load and rotating speed, the COF (0.49) between a rotating PP ball and three fixed H62 plates was approximately 2.3 times higher than that between switched materials of tribo-pairs. Meanwhile, the COF between H62 and PTFE was relatively stable. The unexpected tribological behaviors were ascribed to the thermal and mechanical properties of tribo-pairs. Theoretical analysis revealed that the differences in the maximum local temperature between switching the fixed and moving materials of tribo-pairs were consistent with the differences in the tested COF. This result indicated the precise prediction of the COF of two materials is complexcity, and that thermal and mechanical properties should be properly considered in designing tribo-pairs, because these properties may significantly affect tribological performance.

Factors influencing optical 3D scanning of vinyl polysiloxane impression materials.

PubMed

DeLong, R; Pintado, M R; Ko, C C; Hodges, J S; Douglas, W H

2001-06-01

Future growth in dental practice lies in digital imaging enhancing many chairside procedures and functions. This revolution requires the fast, accurate, and 3D digitizing of clinical records. One such clinical record is the chairside impression. This study investigated how surface angle and surface roughness affect the digitizing of vinyl polysiloxane impression materials. Seventeen vinyl polysiloxane impression materials were digitized with a white light optical digitizing system. Each sample was digitized at 3 different angles: 0 degrees, 22.5 degrees, and 45 degrees, and 2 digitizer camera f-stops. The digitized images were rendered on a computer monitor using custom software developed under NIH/NIDCR grant DE12225. All the 3D images were rotated to the 0 degrees position, cropped using Corel Photo-Paint 8 (Corel Corp, Ottawa, Ontario, Canada), then saved in the TIFF file format. The impression material area that was successfully digitized was calculated as a percentage of the total sample area, using Optimas 5.22 image processing software (Media Cybernetics, LP, Silver Spring, MD). The dependent variable was a Performance Value calculated for each material by averaging the percentage of area that digitized over the 3 angles. New samples with smooth and rough surfaces were made using the 7 impression materials with the largest Performance Values. These samples were tested as before, but with the additional angle of 60 degrees. Silky-Rock die stone (Whip Mix Corp, Louisville, KY) was used as a control. The Performance Values for the 17 impression materials ranged from 0% to 100%. The Performance Values for the 7 best materials were equivalent to the control at f/11 out to a surface angle of 45 degrees; however, only Examix impression material (GC America Inc, Alsip, IL) was equivalent to the control at f/11/\\16. At the 60 degrees surface angle with f/11/\\16, the Performance Values were 0% for all the impression materials, whereas that for the control was 90%. The difference in the Performance Values for the smooth and rough surface textures was 7%, which was not significant. The digitizing performance of vinyl polysiloxane impression materials is highly material and surface angle-dependent and is significantly lower than the die stone control when angles to 60 degrees are included. It is affected to a lesser extent by surface texture. Copyright 2001 by The American College of Prosthodontists.

Environmental assessment for the Processing and Environmental Technology Laboratory (PETL)

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-09-01

The U.S. Department of Energy (DOE) has prepared an environmental assessment (EA) on the proposed Processing and Environmental Technology Laboratory (PETC) at Sandia National Laboratories/New Mexico (SNL/NM). This facility is needed to integrate, consolidate, and enhance the materials science and materials process research and development (R&D) currently in progress at SNL/NM. Based on the analyses in the EA, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, an environmental impact statement is not required, andmore » DOE is issuing this Finding of No Significant Impact (FONSI).« less

Pre-cure freezing affects proteolysis in dry-cured hams.

PubMed

Bañón, S; Cayuela, J M; Granados, M V; Garrido, M D

1999-01-01

Several parameters (sodium chloride, moisture, intramuscular fat, total nitrogen, non-protein nitrogen, white precipitates, free tyrosine, L* a* b* values and acceptability) related with proteolysis during the curing were compared in dry-cured hams manufactured from refrigerated and frozen/thawed raw material. Pre-cure freezing increased the proteolysis levels significantly (p<0.05) in the zones of the ham where water losses and absorption of salt is slowest. Frozen hams present a high incidence of white precipitates, formed mainly by tyrosine crystals. The colour and acceptability scores are similar in frozen and refrigerated hams. The previous freezing and thawing process accentuates the water losses, salt absorption and proteolysis of the cured meat, although it does not significantly affect the sensory quality of the dry-cured ham.

Determine Important Nuclear Fragmentation Processes for Space Radiation Protection in Human Space Explorations

NASA Technical Reports Server (NTRS)

Lin, Zi-Wei

2004-01-01

Space radiation from cosmic ray particles is one of the main challenges for long-term human space explorations such as a permanent moon base or a trip to Mars. Material shielding may provide significant radiation protection to astronauts, and models have been developed in order to evaluate the effectiveness of different shielding materials and to predict radiation environment inside the spacecraft. In this study we determine the nuclear fragmentation cross sections which will most affect the radiation risk behind typical radiation shielding materials. These cross sections thus need more theoretical studies and accurate experimental measurements in order for us to more precisely predict the radiation risk in human space exploration.

Determine Important Nuclear Fragmentation Processes for Space Radiation Protection in Human Space Explorations

NASA Technical Reports Server (NTRS)

Lin, Zi-Wei

2004-01-01

Space radiation from cosmic ray particles is one of the main challenges for long-term human space explorations such as a permanent moon base or a trip to Mars. Material shielding may provide significant radiation protection to astronauts, and models have been developed in order to evaluate the effectiveness of different shielding materials and to predict radiation environment inside the spacecraft. In this study we determine the nuclear fragmentation cross sections which will most affect the radiation risk behind typical radiation shielding materials. These cross sections thus need more theoretical studies and accurate experimental measurements in order for us to more precisely predict the radiation risk in human space explorations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arul Kumar, Mariyappan; Beyerlein, Irene Jane; McCabe, Rodney James

Materials with a hexagonal close-packed (hcp) crystal structure such as Mg, Ti and Zr are being used in the transportation, aerospace and nuclear industry, respectively. Material strength and formability are critical qualities for shaping these materials into parts and a pervasive deformation mechanism that significantly affects their formability is deformation twinning. The interaction between grain boundaries and twins has an important influence on the deformation behaviour and fracture of hcp metals. Here, statistical analysis of large data sets reveals that whether twins transmit across grain boundaries depends not only on crystallography but also strongly on the anisotropy in crystallographic slip.more » As a result, we show that increases in crystal plastic anisotropy enhance the probability of twin transmission by comparing the relative ease of twin transmission in hcp materials such as Mg, Zr and Ti.« less

Ketoprofen spray-dried microspheres based on Eudragit RS and RL: study of the manufacturing parameters.

PubMed

Rassu, Giovanna; Gavini, Elisabetta; Spada, Gianpiera; Giunchedi, Paolo; Marceddu, Salvatore

2008-11-01

The preparation of ketoprofen spray-dried microspheres can be affected by the long drug recrystallization time. Polymer type and drug-polymer ratio as well as manufacturing parameters affect the preparation. The purpose of this work was to evaluate the possibility to obtain ketoprofen spray-dried microspheres using the Eudragit RS and RL; the influence of the spray-drying parameters on morphology, dimension, and physical stability of microspheres was studied. Ketoprofen microspheres based on Eudragit blend can be prepared by spray-drying and the nebulization parameters do not influence significantly particle properties; nevertheless, they can be affected by drying and storage methods. No effect of the container material is found.

Wettability changes in polyether impression materials subjected to immersion disinfection

PubMed Central

Shetty, Shweta; Kamat, Giridhar; Shetty, Rajesh

2013-01-01

Background: Disinfection of impression materials prevents cross-contamination; however, the disinfectants may alter the wettability property. The purpose of this investigation was to evaluate the wettability changes of polyether impression material after immersing in four different chemical disinfectant solutions for a period of 10 min and 30 min, respectively. Materials and Methods: A total of 45 samples of polyether dental impression material (Impregum soft, 3MESPE, St. Paul, MN, USA) were randomly divided into nine groups with five specimens each. Each specimen was disc shaped, flat of 32 mm diameter and 3 mm thickness. The samples were immersed in four disinfectant solutions: 2% Glutaraldehyde, 5% sodium hypochlorite, 0.05% iodophor, and 5.25% phenol for 10 min and 30 min, respectively. The control was without disinfection. Wettability of the samples was assessed by measuring the contact angle by using the Telescopic Goniometer. Data were subjected to analysis of variance (Fisher's test) and Tukey's post hoc test for multiple comparisons at 5% level of significance. Results: The contact angle of 20.21° ± 0.22° were recorded in the control samples. After 10 min, the samples that were immersed in 5% sodium hypochlorite and 5.25% phenol showed significant statistical increase in the contact angle as compared to the control (P < 0.001). After 30 min of disinfection, only the samples immersed in 0.05% iodophor showed there were no significant changes in the contact angle, whereas the other disinfectants significantly increased the contact angle and decreased the wettability of the polyether material. Conclusion: Within the limitations of the study, 2% glutaraldehyde proved safe for 10 min of immersion disinfection while 0.05% iodophor holds promise as an effective disinfectant without affecting the wettability of the material. PMID:24130593

Parental material and cultivation determine soil bacterial community structure and fertility.

PubMed

Sun, Li; Gao, Jusheng; Huang, Ting; Kendall, Joshua R A; Shen, Qirong; Zhang, Ruifu

2015-01-01

Microbes are the key components of the soil environment, playing important roles during soil development. Soil parent material provides the foundation elements that comprise the basic nutritional environment for the development of microbial community. After 30 years artificial maturation of cultivation, the soil developments of three different parental materials were evaluated and bacterial community compositions were investigated using the high-throughput sequencing approach. Thirty years of cultivation increased the soil fertility and soil microbial biomass, richness and diversity, greatly changed the soil bacterial communities, the proportion of phylum Actinobacteria decreased significantly, while the relative abundances of the phyla Acidobacteria, Chloroflexi, Gemmatimonadetes, Armatimonadetes and Nitrospira were significantly increased. Soil bacterial communities of parental materials were separated with the cultivated ones, and comparisons of different soil types, granite soil and quaternary red clay soil were similar and different with purple sandy shale soil in both parental materials and cultivated treatments. Bacterial community variations in the three soil types were affected by different factors, and their alteration patterns in the soil development also varied with soil type. Soil properties (except total potassium) had a significant effect on the soil bacterial communities in all three soil types and a close relationship with abundant bacterial phyla. The amounts of nitrogen-fixing bacteria as well as the abundances of the nifH gene in all cultivated soils were higher than those in the parental materials; Burkholderia and Rhizobacte were enriched significantly with long-term cultivation. The results suggested that crop system would not deplete the nutrients of soil parental materials in early stage of soil maturation, instead it increased soil fertility and changed bacterial community, specially enriched the nitrogen-fixing bacteria to accumulate nitrogen during soil development. © FEMS 2014. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Growth-dependent effects of dietary protein concentration and quality on the biomechanical properties of the diaphyseal rat femur.

PubMed

Alippi, Rosa M; Picasso, Emilio; Huygens, Patricia; Bozzini, Carlos E; Bozzini, Clarisa

2012-01-01

This study compares the effects of feeding growing rats with increasing concentrations of casein (C) and wheat gluten (G), proteins that show different biological qualities, on the morphometrical and biomechanical properties of the femoral diaphysis. Female rats were fed with one of ten diets containing different concentrations (5-30%) of C and G between the 30th and 90th days of life (Control=C-20%). Biomechanical structural properties of the right femur middiaphysis were estimated using a 3-point bending mechanical test with calculation of some indicators of bone material properties. Body weight and length were affected by treatments, values being highest in rats fed the C-20% diet. G diets affected negatively both parameters. Changes in cross-sectional geometry (mid-diaphyseal cross-sectional and cortical areas, femoral volume, and rectangular moment of inertia) were positively related to the C content of the diet, while they were severely and negatively affected by G diets. Similar behaviors were observed in the bone structural properties (fracture load, yielding load, diaphyseal stiffness and elastic energy absorption). When values of strength and stiffness were normalized for body weight, the differences disappeared. The bone material quality indicators (elastic modulus, yielding stress, elastic energy absorption/volume) did not differ significantly among all studied groups. Femoral calcium concentration in ashes was not significantly different among groups. The clear differences in strength and stiffness of bone beams induced by dietary protein concentration and quality seemed to be the result of an induced subnormal gain in bone structural properties as a consequence of a correlative subnormal gain in bone growth and mass, yet not in bone material properties. Copyright © 2011 SEEN. Published by Elsevier Espana. All rights reserved.

Analysing the Friction Stir Welded Joints of AA2219 Al-Cu Alloy in Different Heat-Treated-State

NASA Astrophysics Data System (ADS)

Venkateswarlu, D.; Cheepu, Muralimohan; Kranthi kumar, B.; Mahapatra, M. M.

2018-03-01

Aluminium alloy AA2219 is widely used in light weight structural applications where the good corrosion resistance and specific weight required. The fabrication of this alloy using friction stir welding process is gaining interest towards finding the characteristics of the weld metal properties, since this process involved in the welded materials does not melt and recast. In the present investigation, friction stir welding process was used for different heat treated conditions of 2219-T87 and 2219-T62 aluminium alloys to find the influence of base metal on characteristics of the joints. The experimental output results exhibited that, mechanical properties, weld metal characteristics and joint failure locations are significantly affected by the different heat treatment conditions of the substrate. The joints tensile and yield strength of the 2219-T87 welds was higher than the 2219-T62 welds. Hardness distribution in the stir zone was significantly varied between two different heat treaded material conditions. The microstructural features of the 2219-T62 welds reveal the coarse grains formation in the thermo-mechanically affected zone and heat affected zone. The joint efficiency of the 2219- T82 welds is 59.87%, while that of 2219-T62 welds is 39.10%. In addition, the elongation of the joint also varied and the joints failure location characteristics are different for two different types heat treated condition joints.

Thermoresponsive Polymers with Lower Critical Solution Temperature- or Upper Critical Solution Temperature-Type Phase Behaviour Do Not Induce Toxicity to Human Endothelial Cells.

PubMed

Ji, Yuejia; Zhu, Mengxiang; Gong, Yu; Tang, Haoyu; Li, Juan; Cao, Yi

2017-01-01

Thermoresponsive polymers have gained extensive attention as biomedical materials especially for targeted drug delivery systems. We have recently developed water-soluble polypeptide-based thermoresponsive polymers that exhibit lower critical solution temperature (LCST)- or upper critical solution temperature (UCST)-type phase behaviours. In this study, the toxicity of these polymers to human umbilical vein endothelial cells (HUVECs) was investigated to assess the safety and biocompatibility. Up to 100 μg/ml, thermoresponsive polymers did not induce cytotoxicity to HUVECs, showing as unaltered mitochondrial viability assessed as cell counting kit-8 (CCK-8) assay and membrane integrity assessed as lactate dehydrogenase (LDH) assay. Inflammatory response, assessed as the release of chemokine-soluble monocyte chemotactic protein 1 (sMCP-1) and interleukin-8 (IL-8) as well as cytokine IL-6, was not significantly affected by the polymers. In addition, 1 μM thapsigargin (TG), an endoplasmic reticulum (ER) stress inducer, significantly decreased mitochondrial viability, but did not affect membrane integrity or inflammatory response. The presence of thermoresponsive polymers with LCST-type phase behaviour did not further affect the effects of TG. In conclusion, the thermoresponsive polymers used in this study are not toxic to endothelial cells and therefore could be further considered as safe materials for biomedical applications. © 2016 Nordic Association for the Publication of BCPT (former Nordic Pharmacological Society).

Comparison of fit accuracy and torque maintenance of zirconia and titanium abutments for internal tri-channel and external-hex implant connections

PubMed Central

Siadat, Hakimeh; Beyabanaki, Elaheh; Mousavi, Niloufar

2017-01-01

PURPOSE This in vitro study aimed to evaluate the effect of implant connection design (external vs. internal) on the fit discrepancy and torque loss of zirconia and titanium abutments. MATERIALS AND METHODS Two regular platform dental implants, one with external connection (Brånemark, Nobel Biocare AB) and the other with internal connection (Noble Replace, Nobel Biocare AB), were selected. Seven titanium and seven customized zirconia abutments were used for each connection design. Measurements of geometry, marginal discrepancy, and rotational freedom were done using video measuring machine. To measure the torque loss, each abutment was torqued to 35 Ncm and then opened by means of a digital torque wrench. Data were analyzed with two-way ANOVA and t-test at α=0.05 of significance. RESULTS There were significant differences in the geometrical measurements and rotational freedom between abutments of two connection groups (P<.001). Also, the results showed significant differences between titanium abutments of internal and external connection implants in terms of rotational freedom (P<.001). Not only customized internal abutments but also customized external abutments did not have the exact geometry of prefabricated abutments (P<.001). However, neither connection type (P=.15) nor abutment material (P=.38) affected torque loss. CONCLUSION Abutments with internal connection showed less rotational freedom. However, better marginal fit was observed in externally connected abutments. Also, customized abutments with either connection could not duplicate the exact geometry of their corresponding prefabricated abutment. However, neither abutment connection nor material affected torque loss values. PMID:28874994

Corrosion initiation and propagation behavior of corrosion resistant concrete reinforcing materials

NASA Astrophysics Data System (ADS)

Hurley, Michael F.

The life of a concrete structure exposed to deicing compounds or seawater is often limited by chloride induced corrosion of the steel reinforcement. In this study, the key material attributes that affect the corrosion initiation and propagation periods were studied. These included material composition, surface condition, ageing time, propagation behavior during active corrosion, morphology of attack, and type of corrosion products generated by each rebar material. The threshold chloride concentrations for solid 316LN stainless steel, 316L stainless steel clad over carbon steel, 2101 LDX, MMFX-2, and carbon steel rebar were investigated using electrochemical techniques in saturated calcium hydroxide solutions. Surface preparation, test method, duration of period exposed to a passivating condition prior to introduction of chloride, and presence of cladding defects all affected the threshold chloride concentration obtained. A model was implemented to predict the extension of time until corrosion initiation would be expected. 8 years was the predicted time to corrosion initiation for carbon steel. However, model results confirmed that use of 316LN may increase the time until onset of corrosion to 100 years or more. To assess the potential benefits afforded by new corrosion resistant rebar alloys from a corrosion resistance standpoint the corrosion propagation behavior and other factors that might affect the risk of corrosion-induced concrete cracking must also be considered. Radial pit growth was found to be ohmically controlled but repassivation occurred more readily at high potentials in the case of 316LN and 2101 stainless steels. The discovery of ohmically controlled propagation enabled transformation of propagation rates from simulated concrete pore solution to less conductive concrete by accounting for resistance changes in the surrounding medium. The corrosion propagation behavior as well as the morphology of attack directly affects the propensity for concrete cracking. Experimental results were used in conjunction with an existing model to predict the time until concrete cracking occurs for new rebar materials. The results suggest that corrosion resistant materials offer a significant extension to the corrosion propagation stage over carbon steel, even in very aggressive conditions because small, localized anodes develop when initiated.

Effects of spoil texture on growth of K-31 tall fescue

Treesearch

David H. Van Lear

1971-01-01

Growth of K-31 tall fescue (Festuca arundinacea) was significantly affected by the particle-size distribution, or texture, of four spoils from eastern Kentucky. Growth on spoils having no toxic chemical properties generally was greatest where texture consisted of about equal quantities of soil-size material and a coarser fraction (2 mm. to 6.4 mm.),...

Consideration of Materials for Aircraft Brakes

NASA Technical Reports Server (NTRS)

Peterson, M. B.; Ho, T.

1972-01-01

An exploratory investigation was conducted concerning materials and their properties for use in aircraft brakes. Primary consideration was given to the heat dissipation and the frictional behavior of materials. Used brake pads and rotors were analyzed as part of the investigation. A simple analysis was conducted in order to determine the most significant factors which affect surface temperatures. It was found that where size and weight restrictions are necessary, the specific heat of the material, and maintaining uniform contact area are the most important factors. A criterion was suggested for optimum sizing of the brake disks. Bench friction tests were run with brake materials. It was found that there is considerable friction variation due to the formation and removal of surface oxide films. Other causes of friction variations are surface softening and melting. The friction behavior at high temperature was found to be more characteristic of the steel surface rather than the copper brake material. It is concluded that improved brake materials are feasible.

Application of nanomaterials in two-terminal resistive-switching memory devices

PubMed Central

Ouyang, Jianyong

2010-01-01

Nanometer materials have been attracting strong attention due to their interesting structure and properties. Many important practical applications have been demonstrated for nanometer materials based on their unique properties. This article provides a review on the fabrication, electrical characterization, and memory application of two-terminal resistive-switching devices using nanomaterials as the active components, including metal and semiconductor nanoparticles (NPs), nanotubes, nanowires, and graphenes. There are mainly two types of device architectures for the two-terminal devices with NPs. One has a triple-layer structure with a metal film sandwiched between two organic semiconductor layers, and the other has a single polymer film blended with NPs. These devices can be electrically switched between two states with significant different resistances, i.e. the ‘ON’ and ‘OFF’ states. These render the devices important application as two-terminal non-volatile memory devices. The electrical behavior of these devices can be affected by the materials in the active layer and the electrodes. Though the mechanism for the electrical switches has been in argument, it is generally believed that the resistive switches are related to charge storage on the NPs. Resistive switches were also observed on crossbars formed by nanotubes, nanowires, and graphene ribbons. The resistive switches are due to nanoelectromechanical behavior of the materials. The Coulombic interaction of transient charges on the nanomaterials affects the configurable gap of the crossbars, which results into significant change in current through the crossbars. These nanoelectromechanical devices can be used as fast-response and high-density memory devices as well. PMID:22110862

The effect of thermocycling on the fracture toughness and hardness of core buildup materials.

PubMed

Medina Tirado, J I; Nagy, W W; Dhuru, V B; Ziebert, A J

2001-11-01

Thermocycling has been shown to cause surface degradation of many dental materials, but its effect on the fracture toughness and hardness of direct core buildup materials is unknown. This study was designed to determine the effect of thermocycling on the fracture toughness and hardness of 5 core buildup materials. Fifteen specimens were prepared from each of the following materials: Fluorocore, VariGlass VLC, Valiant PhD, Vitremer, and Chelon-Silver. American Standard for Testing Materials guidelines for single-edge notch, bar-shaped specimens were used. Ten specimens of each material were thermocycled for 2000 cycles; the other 5 specimens were not thermocycled. All specimens were subjected to 3-point bending in a universal testing machine. The load at fracture was recorded, and the fracture toughness (K(IC)) was calculated. Barcol hardness values were also determined. Data were analyzed with 1-way analysis of variance and compared with the Tukey multiple range test (P<.05). Pearson's correlation coefficient was also calculated to measure the association between fracture toughness and hardness. Fluorocore had the highest thermocycled mean K(IC) and Valiant PhD the highest non-thermocycled K(IC). Chelon-Silver demonstrated the lowest mean K(IC) both before and after thermocycling. One-way analysis of variance demonstrated significant differences between conditions, and the Tukey test showed significant differences (P<.05) between materials for both conditions. Most specimens also showed significant hardness differences between conditions. Pearson's correlation coefficient indicated only a mild-to-moderate correlation between hardness and fracture toughness. Within the limitations of this study, the thermocycling process negatively affected the fracture toughness and hardness of the core buildup materials tested.

Effect of Processing on Silk-Based Biomaterials: Reproducibility and Biocompatibility

PubMed Central

Wray, Lindsay S.; Hu, Xiao; Gallego, Jabier; Georgakoudi, Irene; Omenetto, Fiorenzo G.; Schmidt, Daniel; Kaplan, David L.

2012-01-01

Silk fibroin has been successfully used as a biomaterial for tissue regeneration. In order to prepare silk fibroin biomaterials for human implantation a series of processing steps are required to purify the protein. Degumming to remove inflammatory sericin is a crucial step related to biocompatibility and variability in the material. Detailed characterization of silk fibroin degumming is reported. The degumming conditions significantly affected cell viability on the silk fibroin material and the ability to form three-dimensional porous scaffolds from the silk fibroin, but did not affect macrophage activation or β-sheet content in the materials formed. Methods are also provided to determine the content of residual sericin in silk fibroin solutions and to assess changes in silk fibroin molecular weight. Amino acid composition analysis was used to detect sericin residuals in silk solutions with a detection limit between 1.0% and 10% wt/wt, while fluorescence spectroscopy was used to reproducibly distinguish between silk samples with different molecular weights. Both methods are simple and require minimal sample volume, providing useful quality control tools for silk fibroin preparation processes. PMID:21695778

Glow discharge plasma pretreatment enhances osteoclast differentiation and survival on titanium plates.

PubMed

Kawai, Hiroyuki; Shibata, Yo; Miyazaki, Takashi

2004-05-01

Despite the fact that several reports have demonstrated osteoclast activity on various bioactive ceramics, osteoclast functions on surface-modified titanium have not come under focus. This study aimed to examine whether the increasing surface energy of glow discharge plasma (GDP) involved in protein adhesion containing the RGD (Arg-Gly-Asp) sequence affects osteoclast responses on titanium plates. We examined osteoclast differentiation and survival rates on titanium plates with and without GDP. The amounts of osteoclasts on titanium plates were not increased by GDP after 1 week. However, osteoclast differentiation was greatly activated by GDP pretreatment, as tartrate-resistant acid phosphatase synthesis significantly increased on the titanium plates with GDP. Additionally, since the presence of osteoclasts was detected only on the titanium plates with GDP, even after 4h cultivation in a coculture test, the osteoclasts survival rate was increased by GDP pretreatment. As osteoclast responses were affected even on surface modified metallic materials, we concluded that novel approaches are needed not only for osteoclastic resorption on ceramic materials but also for osteoclast responses on surface-modified metallic materials.

An Experimental Test of Factors Attracting Deer Mice into Buildings.

PubMed

Kuenzi, Amy J; Douglass, Richard

2009-09-01

Deer mice (Peromyscus maniculatus) are the principal reservoir host of Sin Nombre virus (SNV). Deer mice use a wide variety of habitats including peridomestic settings in and around human dwellings, their presence in and around homes has been implicated as a risk factor for acquiring Hantavirus Pulmonary Syndrome. Deer mice are believed to enter buildings in order to gain access to a variety of resources including food, bedding material, and better thermal microclimates. However, no one has experimentally tested which factors influence mice use of buildings. We conducted experiments using small simulated buildings to determine the effects of two factors, i.e., food and bedding material, on mouse activity in these buildings. We also examined if these effects varied with time of year. We found that deer mice entered our buildings regardless of the presence or absence of food or bedding. However, the amount of activity in buildings was affected by what they contained. We found significantly higher indices of activity in buildings containing food compared to both empty buildings (control) and buildings containing bedding material. Time of year did not affect activity in buildings.

Dynamic Modelling of Embeddable Piezoceramic Transducers

PubMed Central

Li, Xu; Li, Hongnan; Wang, Zhijie; Song, Gangbing

2017-01-01

Embedded Lead Zirconate Titanate (PZT) transducers have been widely used in research related to monitoring the health status of concrete structures. This paper presents a dynamic model of an embeddable PZT transducer with a waterproof layer and a protecting layer. The proposed model is verified by finite-element method (FEM). Based on the proposed model, the factors influencing the dynamic property of the embeddable PZT transducers, which include the material and thickness of the protecting layer, the material and thickness of the waterproof layer, and the thickness of the PZT, are analyzed. These analyses are further validated by a series of dynamic stress transfer experiments on embeddable PZT transducers. The results show that the excitation frequency can significantly affect the stress transfer of the PZT transducer in terms of both amplitude and signal phase. The natural frequency in the poling direction for the PZT transducer is affected by the material properties and the thickness of the waterproof and protecting layers. The studies in this paper will provide a scientific basis to design embeddable PZT transducers with special functions. PMID:29206150

Advances in Discrete Dislocation Dynamics Modeling of Size-Affected Plasticity

NASA Astrophysics Data System (ADS)

El-Awady, Jaafar A.; Fan, Haidong; Hussein, Ahmed M.

In dislocation-mediated plasticity of crystalline materials, discrete dislocation dynamics (DDD) methods have been widely used to predict the plastic deformation in a number of technologically important problems. These simulations have led to significant improvement in the understanding of the different mechanism that controls the mechanical properties of crystalline materials, which can greatly accelerate the future development of materials with superior properties. This chapter provides an overview of different practical applications of both two-dimensional and three-dimensional DDD simulations in the field of size-affected dislocation-mediated plasticity. The chapter is divided into two major tracks. First, DDD simulations focusing on aspects of modeling size-dependent plasticity in single crystals in uniaxial micro-compression/tension, microtorsion, microbending, and nanoindentation are discussed. Special attention is directed towards the role of cross-slip and dislocation nucleation on the overall response. Second, DDD simulations focusing on the role of interfaces, including grain and twin boundaries, on dislocation-mediated plasticity are discussed. Finally, a number of challenges that are withholding DDD simulations from reaching their full potential are discussed.

Effect of surface material on electrostatic charging of houseflies (Musca domestica L).

PubMed

McGonigle, Daniel F; Jackson, Chris W

2002-04-01

Houseflies (Musca domestica L) accumulated electrostatic charges when walking over clean, uncharged dielectric surfaces. The charges elicited on a walking housefly by a range of materials were quantified, allowing a triboelectric series to be determined relative to M domestica. This ranged from surfaces that charged individuals positively, e.g. Correx (corrugated polypropylene) [.1 (+/- 4.2)pC], to those that applied a negative charge, e.g. clear cast acrylic [-14.9 (+/- 2.9)pC]. Maximum positive and negative charges accumulated by individual M domestica were +73 and -27 pC. Replicate measurements on the same fly and surface showed little variation. Variation between individuals was not related to sex and was not consistent between surfaces. Different materials charged M domestica significantly differently and individual flies had significantly different charging properties. Variation in temperature between 21.3 degrees C and 24.7 degrees C and humidity between 24% and 41% RH significantly affected charge accumulated by M domestica on some surfaces, although further experimentation is needed to confirm this. The implications of this work are discussed in relation to insect trap design and pollination biology.

Effect of polymerization technique and glass fiber addition on the surface roughness and hardness of PMMA denture base material.

PubMed

Gad, Mohammed M; Rahoma, Ahmed; Al-Thobity, Ahmad M

2018-06-20

The current study evaluated the effects of autoclave polymerization both with and without glass fiber (GF) reinforcement on the surface roughness and hardness of acrylic denture base material. Ninety disc specimens (30×2.5 mm) were prepared from Vertex resin and divided according to polymerization techniques into a water bath, short and long autoclave polymerization groups. Tested groups were divided into three subgroups according to the GF concentration (0, 2.5, and 5 wt%). Profilometer and Vickers hardness tests were performed to measure surface roughness and hardness. ANOVA and Tukey-Kramer multiple comparison tests analyzed the results, and p≤0.05 was considered statistically significant. Autoclave polymerization significantly decreased the surface roughness and increased the hardness of acrylic resin without GF reinforcement (p<0.05). However, 5 wt% GF addition significantly increased surface roughness and decreased hardness of the autoclave polymerized denture base resin (p<0.05). Surface properties of Polymethyl methacrylate (PMMA) denture base material improved with autoclave polymerization and negatively affected with GFs addition.

Contribution of postpolymerization conditioning and storage environments to the mechanical properties of three interim restorative materials.

PubMed

Thompson, Geoffrey A; Luo, Qing

2014-09-01

Because polymer-based interim restorative materials are weak, even well-made restorations sometimes fail before the definitive restoration is ready for insertion. Therefore, knowing which fabrication procedures and service conditions affect mechanical properties is important, particularly over an extended period. The purpose of this study was to evaluate the effect of thermal treatment, surface sealing, thermocycling, storage media, storage temperature, and age on autopolymerizing poly(methylmethacrylate) and bis-acryl interim restorative materials. Outcome measures were flexural strength, Vickers surface microhardness, and impact strength. Flexural strength and microhardness of poly(methylmethacrylate) (Jet Acrylic) and 2 bis-acryl-composite resin (Protemp 3 Garant and Integrity) interim restorative materials were evaluated as affected by storage media, storage temperature, storage time, thermocycling, postpolymerization thermal treatment, or application of a surface sealer. In total, 2880 beam specimens (25×2×2 mm) were fabricated. Mechanical property analyses were made at 10 days, 30 days, 6 months, and 1 year after specimen preparation. Flexural strength was determined by using a 3-point bending test in a universal testing machine with a 1 kN load cell at a crosshead speed of 5.0 mm min(-1). Fracture specimens were recovered and used for determining Vickers microhardness. Measurements were made with a 0.1 N load and 15 second dwell time. Three microhardness measurements were made for each specimen, and the mean was used for reporting Vickers microhardness. Notched impact specimens (64×12.7×6.35 mm) were fabricated from Jet, Protemp 3 Garant, and Integrity interim restorative materials, yielding 288 impact specimens. Impact strengths were assessed at 10 days, 30 days, 6 months, and 1 year with a 2 J pendulum. The effects of the various experimental treatments were determined and rank ordered with analysis of variance, F ratios, and least square means differences Student t tests (α=.05). All experimental treatments investigated had significant effects on flexural strength, with material (P<.001) and thermocycling (P<.001) being dominant. Moreover, all experimental treatments investigated had a significant overall impact on Vickers microhardness with material (P<.001) and Palaseal glaze (P<.001) showing large effects. Material (P<.001) and age (P=.010) had a significant effect on impact strength. Mechanical properties of some interim polymeric materials can be improved by postpolymerization heat treatments or surface glazing. This procedure may extend the useful lifetime of some bis-acryl interim restorations. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Grain neighbour effects on twin transmission in hexagonal close-packed materials

DOE PAGES

Arul Kumar, Mariyappan; Beyerlein, Irene Jane; McCabe, Rodney James; ...

2016-12-19

Materials with a hexagonal close-packed (hcp) crystal structure such as Mg, Ti and Zr are being used in the transportation, aerospace and nuclear industry, respectively. Material strength and formability are critical qualities for shaping these materials into parts and a pervasive deformation mechanism that significantly affects their formability is deformation twinning. The interaction between grain boundaries and twins has an important influence on the deformation behaviour and fracture of hcp metals. Here, statistical analysis of large data sets reveals that whether twins transmit across grain boundaries depends not only on crystallography but also strongly on the anisotropy in crystallographic slip.more » As a result, we show that increases in crystal plastic anisotropy enhance the probability of twin transmission by comparing the relative ease of twin transmission in hcp materials such as Mg, Zr and Ti.« less

Materials selection guidelines for geothermal energy utilization systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ellis, P.F. II; Conover, M.F.

1981-01-01

This manual includes geothermal fluid chemistry, corrosion test data, and materials operating experience. Systems using geothermal energy in El Salvador, Iceland, Italy, Japan, Mexico, New Zealand, and the United States are described. The manual provides materials selection guidelines for surface equipment of future geothermal energy systems. The key chemical species that are significant in determining corrosiveness of geothermal fluids are identified. The utilization modes of geothermal energy are defined as well as the various physical fluid parameters that affect corrosiveness. Both detailed and summarized results of materials performance tests and applicable operating experiences from forty sites throughout the world aremore » presented. The application of various non-metal materials in geothermal environments are discussed. Included in appendices are: corrosion behavior of specific alloy classes in geothermal fluids, corrosion in seawater desalination plants, worldwide geothermal power production, DOE-sponsored utilization projects, plant availability, relative costs of alloys, and composition of alloys. (MHR)« less

Durability Challenges for Next Generation of Gas Turbine Engine Materials

NASA Technical Reports Server (NTRS)

Misra, Ajay K.

2012-01-01

Aggressive fuel burn and carbon dioxide emission reduction goals for future gas turbine engines will require higher overall pressure ratio, and a significant increase in turbine inlet temperature. These goals can be achieved by increasing temperature capability of turbine engine hot section materials and decreasing weight of fan section of the engine. NASA is currently developing several advanced hot section materials for increasing temperature capability of future gas turbine engines. The materials of interest include ceramic matrix composites with 1482 - 1648 C temperature capability, advanced disk alloys with 815 C capability, and low conductivity thermal barrier coatings with erosion resistance. The presentation will provide an overview of durability challenges with emphasis on the environmental factors affecting durability for the next generation of gas turbine engine materials. The environmental factors include gaseous atmosphere in gas turbine engines, molten salt and glass deposits from airborne contaminants, impact from foreign object damage, and erosion from ingestion of small particles.

Effect of two different bleaching regimens on the gloss of tooth colored restorative materials.

PubMed

Yalcin, Filiz; Gürgan, Sevil

2005-05-01

Vital tooth bleaching with peroxide is one of the most common cosmetic procedures in dentistry and can be accomplished using a variety of methods or regimens. Recently, new generation of tooth color restorative materials were introduced to market. The purpose of this in vitro study was to determine the gloss changes of three different tooth color restorative materials: Flowable composite (Filtek Flow/3M), packable composite (Filtek P60/3M) and ormocer (Definite/DEGUSSA) after two different bleaching regimens (Vivastyle/VIVADENT) and (Crest Professional Whitestrips/PROCTER and GAMBLE). 16 specimens 30 x 30 x 2 mm size were fabricated from each restorative material. After gloss values were measured with gloss meter, at two different angles of illumination (20 and 60 degrees ), 10% carbamide peroxide (Vivastyle) was applied for 2 h per day for fourteen days to the half of the specimens while 6.5% hydrogen peroxide strip bands (Crest Professional Whitestrips) were applied to the remaining eight of the specimens for 30 min twice daily for 14 days. During the test period the specimens were stored in 37 degrees C and 100% relative humidity. At the end of bleaching regimen the gloss measurements were repeated and the data were subjected to statistical analysis. The Wilcoxon Signed Rank Test analysis revealed that the gloss values were affected by both bleaching regimens (P=0.012). Whitestrips decreased the gloss values of Filtek P60 (at 20 and 60 degrees , P<0.001) and Filtek Flow (at 20 degrees , P=0.05 and at 60 degrees , P=0.05) significantly compared to Vivastyle, while the gloss values of Definite did not show any significant change between Vivastyle and Whitestrips application (at 20 degrees P=0.279; at 60 degrees , P=0.279, Mann-Whitney U Test). The gloss values of materials were significantly different before (at 20 degrees P<0.001; at 60 degrees , P=0.003) and after bleaching (at 20 degrees P<0.05; at 60 degrees , P<0.05) with the highest value of Filtek Flow followed Filtek P60 and then by Definite (Kruskal Wallis test). As the gloss of tooth colored restorative materials could be affected by bleaching regimens, it is necessary to consider the type of the material before starting the treatment.

The Money Buffer Effect in China: A Higher Income Cannot Make You Much Happier but Might Allow You to Worry Less

PubMed Central

Li, Bin; Li, Aimei; Wang, Xiaotian; Hou, Yunsong

2016-01-01

This study examined the possibility that there is a curvilinear relationship between income and subjective well-being in China. This study also investigated whether this curvilinear relationship is moderated by social class and mediated by respondents' material affluence. The study was conducted in China, and the sample consisted of 900 blue-collar workers and 546 white-collar workers. The results for emotional well-being showed that income significantly predicted negative affect but not positive affect. This finding indicates that in China, high incomes may not make people happier but might allow them to worry less, which we call the “money buffer effect.” The results also showed that material affluence mediates the interaction effect between income and social class on subjective well-being. The implications of these results for future research and practice are discussed. PMID:26941687

A low-ignition energy, SCB, thermite igniter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bickes, R.W. Jr.; Grubelich, M.C.; Wackerbarth, D.E.

1996-06-01

The authors describe threshold ignition studies for semiconductor bridge, SCB, ignition of aluminum/copper oxide (Al/CuO) thermite as a function of the capacitor discharge unit (CDU) firing set discharge capacitance, the charge holder material and the morphology of the CuO. All of the tests were carried out with the devices cooled to 0 F ({minus}18 C). They compared ignition thresholds using a brass charge holder and a G10 charge holder; G10 is a non-conducting, fiber-glass-epoxy composite material. They determined that at 50 V on the discharge capacitor, the thresholds were 30.1 {micro}F and 2.0 {micro}F respectively. The tests revealed that differentmore » CuO morphologies affected the function time (interval between start of the firing set current and the output of the thermite device) but did not significantly affect the threshold sensitivity.« less

Effect of Moisture Exchange on Interface Formation in the Repair System Studied by X-ray Absorption

PubMed Central

Lukovic, Mladena; Ye, Guang

2015-01-01

In concrete repair systems, material properties of the repair material and the interface are greatly influenced by the moisture exchange between the repair material and the substrate. If the substrate is dry, it can absorb water from the repair material and reduce its effective water-to-cement ratio (w/c). This further affects the hydration rate of cement based material. In addition to the change in hydration rate, void content at the interface between the two materials is also affected. In this research, the influence of moisture exchange on the void content in the repair system as a function of initial saturation level of the substrate is investigated. Repair systems with varying level of substrate saturation are made. Moisture exchange in these repair systems as a function of time is monitored by the X-ray absorption technique. After a specified curing age (3 d), the internal microstructure of the repair systems was captured by micro-computed X-ray tomography (CT-scanning). From reconstructed images, different phases in the repair system (repair material, substrate, voids) can be distinguished. In order to quantify the void content, voids were thresholded and their percentage was calculated. It was found that significantly more voids form when the substrate is dry prior to application of the repair material. Air, initially filling voids and pores of the dry substrate, is being released due to the moisture exchange. As a result, air voids remain entrapped in the repair material close to the interface. These voids are found to form as a continuation of pre-existing surface voids in the substrate. Knowledge about moisture exchange and its effects provides engineers with the basis for recommendations about substrate preconditioning in practice. PMID:28787801

The contribution of individual psychological resilience in determining the professional quality of life of Australian nurses

PubMed Central

Hegney, Desley G.; Rees, Clare S.; Eley, Robert; Osseiran-Moisson, Rebecca; Francis, Karen

2015-01-01

Research Topic: The aim of this study was to determine the relative contribution of trait negative affect and individual psychological resilience in explaining the professional quality of life of nurses. Materials and Methods: One thousand, seven hundred and forty-three Australian nurses from the public, private, and aged care sectors completed an online Qualtrics survey. The survey collected demographic data as well as measures of depression, anxiety and stress, trait negative affect, resilience, and professional quality of life. Results: Significant positive relationships were observed between anxiety, depression and stress, trait negative affectivity, burnout, and secondary traumatic stress (compassion fatigue). Significant negative relationships were observed between each of the aforementioned variables and resilience and compassion satisfaction (CS). Results of mediated regression analysis indicated that resilience partially mediates the relationship between trait negative affect and CS. Conclusion: Results confirm the importance of both trait negative affect and resilience in explaining positive aspects of professional quality of life. Importantly, resilience was confirmed as a key variable impacting levels of CS and thus a potentially important variable to target in interventions aimed at improving nurse’s professional quality of life. PMID:26539150

Study of the thermal properties of filaments for 3D printing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trhlíková, Lucie, E-mail: xctrhlikova@fch.vutbr.cz; Zmeskal, Oldrich, E-mail: zmeskal@fch.vutbr.cz; Florian, Pavel, E-mail: xcflorianp@fch.vutbr.cz

Various materials are used for 3D printing, most commonly Acrylonitrile butadiene styrene (ABS), Polylactic acid (PLA), Polyethylene (PET) and Polypropylene (PP). These materials differ mainly in their melting point, which significantly influences the properties of the final products. Filaments are melted in the print head during the printing process. The temperature range is from 150 °C to 250 °C depending on the technology used. The optimum temperature for the cooling substrate on which printing is carried out is chosen so as to ensure uniform cooling and deformation. It generally varies between (40 – 100) °C. From the above it ismore » clear that both temperatures can significantly affect the properties of the printed 3D object. It is therefore important to determine the thermal parameters (thermal conductivity, specific heat and thermal diffusivity) of the materials used across the entire range of temperatures. For evaluating the properties of different types of PLA materials, the step transient method was used, which allows determination of all required parameters using a fractal heat transfer model.« less

Transport of trace metals in runoff from soil and pond ash feedlot surfaces

USGS Publications Warehouse

Vogel, J.R.; Gilley, J.E.; Cottrell, G.L.; Woodbury, B.L.; Berry, E.D.; Eigenbert, R.A.

2011-01-01

The use of pond ash (fly ash that has been placed in evaporative ponds for storage and subsequently dewatered) for feedlot surfaces provides a drier environment for livestock and furnishes economic benefits. However, pond ash is known to have high concentrations of trace elements, and the runoff water-quality effects of feedlot surfaces amended with pond ash are not well defined. For this study, two experimental units (plots) were established in eight feedlot pens. Four of the pens contained unamended soil surfaces, and the remaining four pens had pond-ash amended surfaces. Before each test, unconsolidated surface material was removed from four of the plots for each of the amendment treatments, resulting in eight unamended plots and eight pond-ash amended plots. Concentrations for 23 trace elements were measured in cattle feedlot surface material and in the runoff water from three simulated rainfall events. Trace element concentrations in surface material and runoff did not differ between surface consolidation treatments. Amending the feedlot surface material with pond ash resulted in a significant increase in concentration for 14 of the 17 trace elements. Runoff concentrations for 21 trace elements were affected by pond-ash amendment. Sixteen of 21 trace element concentrations that differed significantly were greater in runoff from unamended soil surfaces. Concentrations in runoff were significantly correlated with concentrations in feedlot surface material for boron, manganese, molybdenum, selenium, and uranium.

Assessing the Effects of Different Multimedia Materials on Emotions and Learning Performance for Visual and Verbal Style Learners

ERIC Educational Resources Information Center

Chen, Chih-Ming; Sun, Ying-Chun

2012-01-01

Multimedia materials are now increasingly used in curricula. However, individual preferences for multimedia materials based on visual and verbal cognitive styles may affect learners' emotions and performance. Therefore, in-depth studies that investigate how different multimedia materials affect learning performance and the emotions of learners…

Development of Fractal Dimension and Characteristic Roughness Models for Turned Surface of Carbon Steels

NASA Astrophysics Data System (ADS)

Zuo, Xue; Zhu, Hua; Zhou, Yuankai; Ding, Cong; Sun, Guodong

2016-08-01

Relationships between material hardness, turning parameters (spindle speed and feed rate) and surface parameters (surface roughness Ra, fractal dimension D and characteristic roughness τ∗) are studied and modeled using response surface methodology (RSM). The experiments are carried out on a CNC lathe for six carbon steel material AISI 1010, AISI 1020, AISI 1030, AISI 1045, AISI 1050 and AISI 1060. The profile of turned surface and the surface roughness value are measured by a JB-5C profilometer. Based on the profile data, D and τ∗ are computed through the root-mean-square method. The analysis of variance (ANOVA) reveals that spindle speed is the most significant factors affecting Ra, while material hardness is the most dominant parameter affecting τ∗. Material hardness and spindle speed have the same influence on D. Feed rate has less effect on three surface parameters than spindle speed and material hardness. The second-order models of RSM are established for estimating Ra, D and τ∗. The validity of the developed models is approximately 80%. The response surfaces show that a surface with small Ra and large D and τ∗ can be obtained by selecting a high speed and a large hardness material. According to the established models, Ra, D and τ∗ of six carbon steels surfaces can be predicted under cutting conditions studied in this paper. The results have an instructive meaning to estimate the surface quality before turning.

Space Environment Factors Affecting the Performance of International Space Station Materials: The First Two Years of Flight Operations

NASA Technical Reports Server (NTRS)

Koontz, Steven L.; Peldey, Michael; Mayeaux, Brian; Milkatarian, Ronald R.; Golden, John; Boeder, paul; Kern, John; Barsamian, Hagop; Alred, John; Soares, Carlos;

Influence of clinical mastitis and its treatment outcome on reproductive performance in crossbred cows: A retrospective study

PubMed Central

Kumar, Narender; Manimaran, A.; Sivaram, M.; Kumaresan, A.; Jeyakumar, S.; Sreela, L.; Mooventhan, P.; Rajendran, D.

2017-01-01

Aim: Evaluation of the effect of clinical mastitis (CM) and its treatment outcome on the reproductive performance in crossbred cows retrospectively. Materials and Methods: Datasets of 835 lactating cows affected with CM during a period of 12 years (2001-2012) were considered for this study. Mastitis treatment related data and reproductive parameters such as days to first detected heat (DTFDH), days to first insemination (DTFI), days open (DO), and number of services per conception (SC) were collected from mastitis treatment and artificial insemination registers, respectively. Data were analyzed by ANOVA using SPSS 20 software. The means were compared with the Duncan’s multiple comparison post-hoc test. Results: CM affected cows had significantly (p<0.05) higher DTFDH, DTFI, DO and SC compared to clinically healthy cows. Cows diagnosed with a single episode of CM had significantly (p<0.05) delayed DTFDH while, DO and SC were significantly higher (p<0.05) in cows diagnosed by multiple episodes of CM. SC was significantly (p<0.05) higher in cows diagnosed with both relapse and recurrence. Severe CM affected cows had significantly (p<0.05) altered reproductive parameters. The reproductive parameters were altered to high extent when CM occurred during the breeding period. Conclusion: CM-affected cows had higher DTFDH, DTFI, DO and SC compared to clinically healthy cows. The negative effects of CM on reproduction parameters were higher when CM occurred during the breeding period. PMID:28620250

Diffused junction p(+)-n solar cells in bulk GaAs. I Fabrication and cell performance

NASA Technical Reports Server (NTRS)

Bhat, I.; Bhat, K. N.; Mathur, G.; Borrego, J. M.; Ghandhi, S. K.

1984-01-01

This paper describes the fabrication of solar cells made by a simple open tube p(+)-diffusion into bulk n-GaAs. In addition, cell performance is provided as an indicator of the quality of bulk GaAs for this application. Initial results using this technique (12.2 percent efficiency at AM1 for 0.5 sq cm cells) are promising, and indicate directions for materials improvement. It is shown that the introduction of the diffusant (zinc) with point defects significantly affects the material properties and results in an increase in current capability.

Energy-absorption capability and scalability of square cross section composite tube specimens

NASA Technical Reports Server (NTRS)

Farley, Gary L.

1987-01-01

Static crushing tests were conducted on graphite/epoxy and Kevlar/epoxy square cross section tubes to study the influence of specimen geometry on the energy-absorption capability and scalability of composite materials. The tube inside width-to-wall thickness (W/t) ratio was determined to significantly affect the energy-absorption capability of composite materials. As W/t ratio decreases, the energy-absorption capability increases nonlinearly. The energy-absorption capability of Kevlar epoxy tubes was found to be geometrically scalable, but the energy-absorption capability of graphite/epoxy tubes was not geometrically scalable.

The relationship between resonance scattering and the formation of an acoustojet under the interaction of ultrasound with a dielectric sphere immersed in water

NASA Astrophysics Data System (ADS)

Minin, I. V.; Minin, O. V.; Tseplyaev, I. S.

2017-08-01

We demonstrated for the first time the influence of the main parameters of dielectric spherical cavity, immersed in water, to transformation of whispering gallery mode into acoustojet (acoustic jets) by interaction of acoustic plane wave scatterer. It has been shown that the relative speed of sound in the material, the relative density of the material and the radius of particle significantly affect the condition for the formation of WGM resonance. However, the "more sensitive" parameter is the relative speed of sound.

Stressed Ge:Ga photoconductors for space-based astronomy. (Is there life beyond 120 micron)

NASA Technical Reports Server (NTRS)

Beeman, J. W.; Haller, E. E.; Hansen, W. L.; Luke, P. N.; Richards, P. L.

1989-01-01

Information is given in viewgraph form. Information is given on the characteristics of stressed Ge:Ga, a spring type stress cavity, mounting hardware, materials parameters affecting dark current, and the behavior of low dark current stressed Ge:Ga. It is concluded that detectors exist today for background-limited detection at 200 microns, that researchers are narrowing in on the significant parameters that effect dark current in stressed photoconductors, that these findings may be applied to other photoconductor materials, and that some creative problem solving for an ionizing effect reset mechanism is needed.

Evaluation of gloss changes of two denture acrylic resin materials in four different beverages.

PubMed

Keyf, Filiz; Etikan, Ilker

2004-03-01

The primary disadvantages of the materials which are used in construction of complete and removable partial dentures is that their esthetic, physical and mechanical properties change rapidly with time in the oral environment. For esthetics, color stability is one of the criteria that needs careful attention. Color may provide important information on the serviceability of these materials. Color change affects the gloss of these materials. The objective of the present study was to determine the gloss changes resulting from the testing process in four different beverages in one heat-polymerized denture base resin and one cold-polymerized denture base repair resin. Thirty-six samples were fabricated for each material. Each sample had a smooth polished and a rough unpolished surface. The gloss measurements were made with a glossmeter before testing. Four different beverages (tea, coffee, cola and cherry juice) were used for testing. Two angles of illumination (20 and 60 degrees) were used for the gloss measurements. The samples were immersed in water, tea, coffee, cola and cherry juice solutions. The gloss of the samples was measured again with the glossmeter at the end of the 45th day and 135th day of testing. The arithmetic mean and standard deviation of each of the samples were calculated and compared with each other statistically by using the Wilcoxon test (within times) (p < or = 0.05 significant), the Kruskal-Wallis analysis of variance (p < or = 0.05 significant) and the Mann-Whitney U-test with Bonforoni correction (when the difference between the samples was significant) (p < or = 0.05 significant). The results of this study revealed that gloss changes occurred after testing in heat-polymerized denture base resin and cold-polymerized denture base repair resin. The significance of the gloss changes exhibited by each sample, kept for different lengths of time in the same solution, were compared using the Wilcoxon test. The results were statistically significant (p < or = 0.05). According to the Kruskal-Wallis analysis of variance, the difference between measurements for angles of illumination was statistically significant (p < or = 0.05). Also according to the Mann-Whitney U-test, the difference between two polished surfaces or two unpolished surfaces was statistically insignificant (p > 0.05), but the difference between smooth polished and rough unpolished surfaces was statistically significant (p < or = 0.05). It was found that either the gloss of heat-polymerized denture base resin or the gloss of cold-polymerized denture base repair resin was affected by tested agents, and the four beverages demonstrated noticeable gloss changes. Cherry juice demonstrated the least change, while tea exhibited the greatest change.

DIFFERENT STROKES FOR DIFFERENT GANGS? AN ANALYSIS OF CAPITAL AMONG LATINO AND ASIAN GANG MEMBERS

PubMed Central

PIH, KAY KEI-HO; DE LA ROSA, MARIO; RUGH, DOUGLAS; MAO, KUORAY

2009-01-01

Gang activity and membership were noted to be significantly related to financial rewards. As such, gang membership and gang activity should also be understood from an economic perspective. In this article, Pierre Bourdieu's framework of capital is used to analyze two separate samples of Latino and Asian gang members. Stark contrasts in socioeconomic backgrounds are recorded among the two samples of gang members, and gang membership and activities are also noticeably dissimilar. Accessibility to economic, cultural, and social capital is argued to affect gang membership and activities. The results suggest that the availability of legitimate and illegitimate capital greatly affects the trajectory and the length of gang involvement. Also, gangs provide significant material and social capital for the respondents of the study. PMID:19578563

[Effect of emotional content and self reference of learning materials on recall performance].

PubMed

Spies, K

1994-01-01

It is assumed that high affective value and high self-reference of learning material help to improve memory performance as these factors allow better memory consolidation (activation hypothesis) or better integration of the new material into existing knowledge structures (extent-of-processing hypothesis). To test this assumption, 60 subjects were shown 16 short advertising films characterized by low vs. high affective value and low vs. high self-reference. Both factors were varied within subjects. After the films had each been presented twice, subjects had to recall the product names and answer two questions to each film. Results showed for both dependent variables that films with high affective values were better remembered than films with low affective values. The same held true--though to a lower extent--with respect to self-reference. According to the expected linear trend, performance was best for material scoring high on affective value as well as on self-reference, while it was worst for material scoring low on both factors.

Analysis of the embodied and operational energy: Study of a suburban house in Athens, Greece

NASA Astrophysics Data System (ADS)

Ghiata, Maria

Operational energy can establish how successful a building is, in terms of environmentally 'considerate' design. Though embodied energy of construction materials also comprises an important indicator of the environmental impact of the material, the construction industry does not really promote it as such. This report enhances the significance of embodied energy and its relationship to operational energy (energy in use). Since buildings are becoming less energy demanding, operational energy will be decreasing, so that embodied energy will be gaining ground in the attempt to protect the environment. By the use of an 'environmentally friendly' house as a case study, it was proven that, though changes of the wall, floor, and insulation materials can take place, the operational energy does not change. What is greatly affected is the embodied energy of these construction materials.

Comparative evaluation of pressure generated on a simulated maxillary oral analog by impression materials in custom trays of different spacer designs: An in vitro study.

PubMed

Chopra, Sakshi; Gupta, Narendra Kumar; Tandan, Amrit; Dwivedi, Ravi; Gupta, Swati; Agarwal, Garima

2016-01-01

Literature reveals that masticatory load on denture bearing tissues through complete dentures should be maximum on primary stress bearing areas and least on relief area in accordance with the histology of underlying tissues. A study to validate the existing beliefs was planned to compare the pressure on mucosa using selective pressure technique and minimal pressure technique, with the incorporation of two different impression materials utilizing the pressure sensors during secondary impression procedure. The study was performed using a maxillary analog. Three pressure sensors were imbedded in the oral analog, one in the mid palatine area and the other two in the right and left ridge crest. Custom trays of two different configurations were fabricated. The two impression materials tested were light body and zinc oxide eugenol. A total of 40 impressions were made. A constant weight of 1 kg was placed, and the pressure was recorded as initial and end pressures. A significant difference in the pressure produced using different impression materials was found (P < 0.001). Light body vinyl polysiloxane produced significantly lesser pressure than zinc oxide eugenol impression materials. The presence of relief did affect the magnitude of pressure at various locations. All impression materials produced pressure during maxillary edentulous impression making. Tray modification is an important factor in changing the amount of pressure produced. The impression materials used also had a significant role to play on the pressures acting on the tissues during impression procedure. Light body VPS impression material may be recommended to achieve minimal pressure on the denture bearing tissues in both selective as well as minimal pressure techniques.

Effect of different impression materials and techniques on the dimensional accuracy of implant definitive casts

PubMed Central

Ebadian, Behnaz; Rismanchian, Mansor; Dastgheib, Badrosadat; Bajoghli, Farshad

2015-01-01

Background: Different factors such as impression techniques and materials can affect the passive fit between the superstructure and implant. The aim of this study was to determine the effect of different impression materials and techniques on the dimensional accuracy of implant definitive casts. Materials and Methods: Four internal hex implants (Biohorizons Ø4 mm) were placed on a metal maxillary model perpendicular to the horizontal plane in maxillary lateral incisors, right canine and left first premolar areas. Three impression techniques including open tray, closed tray using ball top screw abutments and closed tray using short impression copings and two impression materials (polyether and polyvinyl siloxane) were evaluated (n = 60). The changes in distances between implant analogues in mediolateral (x) and anteroposterior (y) directions and analogue angles in x/z and y/z directions in the horizontal plane on the definitive casts were measured by coordinate measuring machine. The data were analyzed by multivariate two-way analysis of variance and one sample t-test (α = 0.05). Results: No statistical significant differences were observed between different impression techniques and materials. However, deviation and distortion of definitive casts had a significant difference with the master model when short impression copings and polyvinyl siloxane impression material were used (P < 0.05). In open tray technique, there was a significant difference in the rotation of analogs compared with the master model with both impression materials (P < 0.05). Conclusion: There was no difference between open and closed tray impression techniques; however, less distortion and deviation were observed in the open tray technique. In the closed tray impression technique, ball top screw was more accurate than short impression copings. PMID:25878678

Attention and material-specific memory in children with lateralized epilepsy.

PubMed

Engle, Jennifer A; Smith, Mary Lou

2010-01-01

Epilepsy is frequently associated with attention and memory problems. In adults, lateralization of seizure focus impacts the type of memory affected (left-sided lesions primarily impact verbal memory, while right-sided lesions primarily impact visual memory), but the relationship between seizure focus and the nature of the memory impairment is less clear in children. The current study examines the correlation between parent-reported attention problems and material-specific memory (verbal or visual-spatial) in 65 children (ages 6-16) with medically intractable lateralized epilepsy. There were no significant differences in attention and memory between those with left-lateralized epilepsy (n=25) and those with right-lateralized epilepsy (n=40). However, in the left-lateralized group attention problems were significantly negatively correlated only with delayed visual memory (r=-.450, p<.05), while the right-lateralized group demonstrated the opposite pattern (attention problems significantly negatively correlated with delayed verbal memory; r=-.331, p<.05). These findings suggest that lateralization of seizure focus may in fact impact children's memory in a material-specific manner, while problems with attention may impact memory more globally. Therefore, interventions designed to improve attention in children with epilepsy may have utility in improving certain aspects of memory, but further suggest that in children with lateralized epilepsy, material-specific memory deficits may not resolve with such interventions.

Channel response to a new hydrological regime in southwestern Australia

NASA Astrophysics Data System (ADS)

Callow, J. N.; Smettem, K. R. J.

2007-02-01

The Kent River flows from semi-arid headwaters in the agricultural (wheatbelt) region of Western Australia to a wetter and forested lower-catchment. It is set in an atypical fluvial environment, with rainfall decreasing inland towards a low-relief upper catchment. Replacement of native deep-rooted perennial vegetation with shallow-rooted seasonal crops has altered the hydrology of the upper catchment. Clearing for agriculture has also increased recharge of regional groundwater systems causing groundwater to rise and mobilise salt stores. This has increased stream salinity which has degradation riparian vegetation and decreased flow resistance. Elevated groundwater has also affected streamflow, increasing flow duration and annual discharge. The altered hydrological regime has affected geomorphic stability, resulting in channel responses that include incision and removal of uncohesive material. Channel response is variable, showing a high dependence on channel morphotype, channel boundary material and severity of salinity (degree of vegetation degradation). Response in confined reaches bounded by sandy material has been characterised by minor lateral bank erosion. In the fine-grained, wider, low-gradient reaches, mid-channel islands have been stripped of sandy sediment where vegetation has degraded. Following an initial period of high erosion rates in these reaches, the channel is now slowly adjusting to a new set of boundary conditions. The variable response has significant implications for management of salt affected rivers in southwestern Australia.

Composite polymer systems with control of local substrate elasticity and their effect on cytoskeletal and morphological characteristics of adherent cells.

PubMed

Chou, Szu-Yuan; Cheng, Chao-Min; LeDuc, Philip R

2009-06-01

At the interface between extracellular substrates and biological materials, substrate elasticity strongly influences cell morphology and function. The associated biological ramifications comprise a diversity of critical responses including apoptosis, differentiation, and motility, which can affect medical devices such as stents. The interactions of the extracellular environment with the substrate are also affected by local properties wherein cells sense and respond to different physical inputs. To investigate the effects of having localized elasticity control of substrate microenvironments on cell response, we have developed a method to control material interface interactions with cells by dictating local substrate elasticity. This system is created by generating a composite material system with alternating, linear regions of polymers that have distinct stiffness characteristics. This approach was used to examine cytoskeletal and morphological changes in NIH 3T3 fibroblasts with emphasis on both local and global properties, noting that cells sense and respond to distinct material elasticities. Isolated cells sense and respond to these local differences in substrate elasticity by extending processes along the interface. Also, cells grown on softer elastic regions at higher densities (in contact with each other) have a higher projected area than isolated cells. Furthermore, when using chemical agents such as cytochalasin-D to disrupt the actin cytoskeleton, there is a significant increase in projected area for cells cultured on softer elastic regions This method has the potential to promote understanding of biomaterial-affected responses in a diversity of areas including morphogenesis, mechanotransduction, stents, and stem cell differentiation.

The effect of contact lens materials on disinfection activity of polyquaternium-1 and myristamidopropyl dimethylamine multipurpose solution against Staphylococcus aureus.

PubMed

Shoff, Megan E; Lucas, Anne D; Phillips, K Scott; Brown, Jennifer N; Hitchins, Victoria M; Eydelman, Malvina B

2012-11-01

This study examined the interaction of seven different lens materials with a multipurpose solution (MPS) containing the disinfectants polyquaternium-1 (0.001%) and myristamidopropyl dimethylamine (0.0005%). The objective of this study was to determine whether the different lens materials affect the concentration of a disinfectant in this commercially available MPS and the efficacy of the disinfectant against Staphylococcus aureus. Silicone hydrogel lenses (galyfilcon A, senofilcon A, comfilcon A, enfilcon A, balafilcon A, and lotrafilcon B) and a conventional hydrogel lens (etafilcon A) were soaked in polypropylene lens cases filled with commercially available MPS containing 0.001% polyquaternium-1 and 0.0005% myristamidopropyl dimethylamine for 6, 12, 24, 72, and 168 hours. Empty lens cases were also filled with MPS. After each time point, solutions from cases containing the seven types of lenses and controls were assayed for activity against S. aureus according to International Standards Organization 14729 standard with modifications. Test solutions were analyzed for polyquaternium-1 and myristamidopropyl dimethylamine concentration at each time point. The concentration of polyquaternium-1 and myristamidopropyl dimethylamine remaining in the lens cases was reduced only slightly over time. Storage with the lenses did not adversely affect biocidal efficacy of the solution, and in some cases, it was significantly better (P=0.0029). The efficacy of this polyquaternium-1 and myristamidopropyl dimethylamine MPS to kill S. aureus was not adversely affected by the presence of lens materials soaking in the cases. Thus, current methods for performing solution antimicrobial testing should be reevaluated.

The interobserver-validated relevance of intervertebral spacer materials in MRI artifacting

PubMed Central

Heidrich, G.; Bruening, T.; Krefft, S.; Buchhorn, G.; Klinger, H.M.

2006-01-01

Intervertebral spacers for anterior spine fusion are made of different materials, such as titanium, carbon or cobalt-chrome, which can affect the post-fusion MRI scans. Implant-related susceptibility artifacts can decrease the quality of MRI scans, thwarting proper evaluation. This cadaver study aimed to demonstrate the extent that implant-related MRI artifacting affects the post-fusion evaluation of intervertebral spacers. In a cadaveric porcine spine, we evaluated the post-implantation MRI scans of three intervertebral spacers that differed in shape, material, surface qualities and implantation technique. A spacer made of human cortical bone was used as a control. The median sagittal MRI slice was divided into 12 regions of interest (ROI). No significant differences were found on 15 different MRI sequences read independently by an interobserver-validated team of specialists (P>0.05). Artifact-affected image quality was rated on a score of 0-1-2. A maximum score of 24 points (100%) was possible. Turbo spin echo sequences produced the best scores for all spacers and the control. Only the control achieved a score of 100%. The carbon, titanium and cobalt-chrome spacers scored 83.3, 62.5 and 50%, respectively. Our scoring system allowed us to create an implant-related ranking of MRI scan quality in reference to the control that was independent of artifact dimensions. The carbon spacer had the lowest percentage of susceptibility artifacts. Even with turbo spin echo sequences, the susceptibility artifacts produced by the metallic spacers showed a high degree of variability. Despite optimum sequencing, implant design and material are relevant factors in MRI artifacting. PMID:16463200

[Prudent use price controls in Chinese medicines market: based on statistical data analysis].

PubMed

Yang, Guang; Wang, Nuo; Huang, Lu-Qi; Qiu, Hong-Yan; Guo, Lan-Ping

2014-01-01

A dispute about the decreasing-price problem of traditional Chinese medicine (TCM) has recently arisen. This article analyzes the statistical data of 1995-2011 in China, the results showed that the main responsibility of expensive health care has no direct relationship with the drug price. The price index of TCM rose significantly slower than the medicine prices, the production margins of TCM affected by the material prices has been diminishing since 1995, continuous price reduction will further depress profits of the TCM industry. Considering the pros and cons of raw materials vary greatly in price, decreasing medicine price behavior will force enterprises to use inferior materials in order to maintain corporate profits. The results have the guiding meaning to medicine price management.

An Investigation of TIG welding parameters on microhardness and microstructure of heat affected zone of HSLA steel

NASA Astrophysics Data System (ADS)

Musa, M. H. A.; Maleque, M. A.; Ali, M. Y.

2018-01-01

Nowadays a wide variety of metal joining methods are used in fabrication industries. In this study, the effect of various welding parameters of the TIG welding process on microhardness, depth, and microstructure of the heat-affected zone (HAZ) of L450 HSLA steel and optimizing these process parameters following Taguchi experimental design was investigated. The microhardness tended to increase significantly with the increase of welding speed from 1.0 to 2.5 mm/s whereas the width of HAZ decreased. The current and arc voltage was found to be less significant in relative comparison. Microstructures of the welded samples were also studied to analyze the changes in the microstructure of the material in terms of ferrite, pearlite, bainite, and martensite formations. Welding speed was found to be the most significant factors leading to changes in microhardness and metallurgical properties. The increase of welding heat input caused an increase in width (depth) of HAZ and the growth of prior austenite grains and then enlarged the grain size of coarse grain heat affected zone (CGHAZ). However, the amount of martensite in the HAZ decreased accompanied by an opposite change of paint. It was observed that the hardness properties and the microstructural feature of HAZ area was strongly affected by the welding parameters.

A Design Research Study of a Curriculum and Diagnostic Assessment System for a Learning Trajectory on Equipartitioning

ERIC Educational Resources Information Center

Confrey, Jere; Maloney, Alan

2015-01-01

Design research studies provide significant opportunities to study new innovations and approaches and how they affect the forms of learning in complex classroom ecologies. This paper reports on a two-week long design research study with twelve 2nd through 4th graders using curricular materials and a tablet-based diagnostic assessment system, both…

Issues related to durability and protection affecting the acceptance and use of engineered wood composites in Europe

Treesearch

Mark Hughes; Jerrold E. Winandy

2007-01-01

Engineered wood composites (EWC) offer significant potential in applications in the built environment, ranging from domestic dwellings to bridges and public buildings. Nevertheless, EWCs, which include products such as glulam, laminated veneer lumber, oriented stand-board, and plywood enjoy a relatively small market share of total wood-based material production and...

Opening a Can of Worm(‐like Micelle)s: The Effect of Temperature of Solutions of Functionalized Dipeptides

PubMed Central

Draper, Emily R.; Su, Hao; Brasnett, Christopher; Poole, Robert J.; Rogers, Sarah; Cui, Honggang; Seddon, Annela

2017-01-01

Abstract A simple heat/cool cycle can be used to significantly affect the properties of a solution of a low‐molecular‐weight gelator at high pH. The viscosity and extensional viscosity are increased markedly, leading to materials with very different properties than when the native solution is used. PMID:28653804

Dynamics of drinking water biofilm in flow/non-flow conditions.

PubMed

Manuel, C M; Nunes, O C; Melo, L F

2007-02-01

Drinking water biofilm formation on polyvinyl chloride (PVC), cross-linked polyethylene (PEX), high density polyethylene (HDPE) and polypropylene (PP) was followed in three different reactors operating under stagnant or continuous flow regimes. After one week, a quasi-steady state was achieved where biofilm total cell numbers per unit surface area were not affected by fluctuations in the concentration of suspended cells. Metabolically active cells in biofilms were around 17-35% of the total cells and 6-18% were able to form colony units in R(2)A medium. Microbiological analysis showed that the adhesion material and reactor design did not affect significantly the biofilm growth. However, operating under continuous flow (0.8-1.9 Pa) or stagnant water had a significant effect on biofilm formation: in stagnant waters, biofilm grew to a less extent. By applying mass balances and an asymptotic biofilm formation model to data from biofilms grown on PVC and HDPE surfaces under turbulent flow, specific growth rates of bacteria in the biofilm were found to be similar for both materials (around 0.15 day(-1)) and much lower than the specific growth rates of suspended bacteria (around 1.8 day(-1)).

Effects of thermally induced denaturation on technological-functional properties of whey protein isolate-based films.

PubMed

Schmid, M; Krimmel, B; Grupa, U; Noller, K

2014-09-01

This study examined how and to what extent the degree of denaturation affected the technological-functional properties of whey protein isolate (WPI)-based coatings. It was observed that denaturation affected the material properties of WPI-coated films significantly. Surface energy decreased by approximately 20% compared with native coatings. Because the surface energy of a coating should be lower than that of the substrate, this might result in enhanced wettability characteristics between WPI-based solution and substrate surface. Water vapor barrier properties increased by about 35% and oxygen barrier properties increased by approximately 33%. However, significant differences were mainly observed between coatings made of fully native WPI and ones with a degree of denaturation of 25%. Higher degrees of denaturation did not lead to further improvement of material properties. This observation offers cost-saving potential: a major share of denatured whey proteins may be replaced by fully native ones that are not exposed to energy-intensive heat treatment. Furthermore, native WPI solutions can be produced with higher dry matter content without gelatinizing. Hence, less moisture has to be removed through drying, resulting in reduced energy consumption. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Measurements of the frame acoustic properties of porous and granular materials

NASA Astrophysics Data System (ADS)

Park, Junhong

2005-12-01

For porous and granular materials, the dynamic characteristics of the solid component (frame) are important design factors that significantly affect the material's acoustic properties. The primary goal of this study was to present an experimental method for measuring the vibration characteristics of this frame. The experimental setup was designed to induce controlled vibration of the solid component while minimizing the influence from coupling between vibrations of the fluid and the solid component. The Biot theory was used to verify this assumption, taking the two dilatational wave propagations and interactions into account. The experimental method was applied to measure the dynamic properties of glass spheres, lightweight microspheres, acoustic foams, and fiberglass. A continuous variation of the frame vibration characteristics with frequency similar to that of typical viscoelastic materials was measured. The vibration amplitude had minimal effects on the dynamic characteristics of the porous material compared to those of the granular material. For the granular material, materials comprised of larger particles and those under larger vibration amplitudes exhibited lower frame wave speeds and larger decay rates.

Reconnaissance for determining effects of land use and surficial geology on concentrations of selected elements on streambed materials from the coal-mining region, southwestern Indiana, October 1979 to March 1980

USGS Publications Warehouse

Wilber, W.G.; Boje, Rita R.

1982-01-01

Streambed materials were collected in October 1979 from 69 watersheds in Southwest Indiana having predominantly forested, agricultural, reclaimed, and unreclaimed mined land use to determine whether concentrations of sorbed and acid-soluble metals and trace elements were affected by land use and surficial geology. Analysis of variance indicated that 10% or more of the total variation in aluminum, arsenic, cobalt, iron, nickel, selenium, and zinc concentrations on streambed materials was accounted for by differences in land use. Concentrations of aluminum, cobalt, iron, nickel, selenium, and zinc on streambed materials smaller than 0.062-millimeter from mined watersheds were significantly greater than the concentrations of these elements on streambed materials from agricultural and forested watersheds. The greater concentrations of these elements on streambed materials are due to (1) their concentrations in mine drainage and their subsequent absorption and (or) copecipitation with the oxides and hydroxides of aluminum and iron and (2) their concentrations in coal and pyritic material in streambed materials. (USGS)

Timoshenko beam model for chiral materials

NASA Astrophysics Data System (ADS)

Ma, T. Y.; Wang, Y. N.; Yuan, L.; Wang, J. S.; Qin, Q. H.

2017-12-01

Natural and artificial chiral materials such as deoxyribonucleic acid (DNA), chromatin fibers, flagellar filaments, chiral nanotubes, and chiral lattice materials widely exist. Due to the chirality of intricately helical or twisted microstructures, such materials hold great promise for use in diverse applications in smart sensors and actuators, force probes in biomedical engineering, structural elements for absorption of microwaves and elastic waves, etc. In this paper, a Timoshenko beam model for chiral materials is developed based on noncentrosymmetric micropolar elasticity theory. The governing equations and boundary conditions for a chiral beam problem are derived using the variational method and Hamilton's principle. The static bending and free vibration problem of a chiral beam are investigated using the proposed model. It is found that chirality can significantly affect the mechanical behavior of beams, making materials more flexible compared with nonchiral counterparts, inducing coupled twisting deformation, relatively larger deflection, and lower natural frequency. This study is helpful not only for understanding the mechanical behavior of chiral materials such as DNA and chromatin fibers and characterizing their mechanical properties, but also for the design of hierarchically structured chiral materials.

Timoshenko beam model for chiral materials

NASA Astrophysics Data System (ADS)

Ma, T. Y.; Wang, Y. N.; Yuan, L.; Wang, J. S.; Qin, Q. H.

2018-06-01

Natural and artificial chiral materials such as deoxyribonucleic acid (DNA), chromatin fibers, flagellar filaments, chiral nanotubes, and chiral lattice materials widely exist. Due to the chirality of intricately helical or twisted microstructures, such materials hold great promise for use in diverse applications in smart sensors and actuators, force probes in biomedical engineering, structural elements for absorption of microwaves and elastic waves, etc. In this paper, a Timoshenko beam model for chiral materials is developed based on noncentrosymmetric micropolar elasticity theory. The governing equations and boundary conditions for a chiral beam problem are derived using the variational method and Hamilton's principle. The static bending and free vibration problem of a chiral beam are investigated using the proposed model. It is found that chirality can significantly affect the mechanical behavior of beams, making materials more flexible compared with nonchiral counterparts, inducing coupled twisting deformation, relatively larger deflection, and lower natural frequency. This study is helpful not only for understanding the mechanical behavior of chiral materials such as DNA and chromatin fibers and characterizing their mechanical properties, but also for the design of hierarchically structured chiral materials.

Wettability changes in polyether impression materials subjected to immersion disinfection.

PubMed

Shetty, Shweta; Kamat, Giridhar; Shetty, Rajesh

2013-07-01

Disinfection of impression materials prevents cross-contamination; however, the disinfectants may alter the wettability property. The purpose of this investigation was to evaluate the wettability changes of polyether impression material after immersing in four different chemical disinfectant solutions for a period of 10 min and 30 min, respectively. A total of 45 samples of polyether dental impression material (Impregum soft, 3MESPE, St. Paul, MN, USA) were randomly divided into nine groups with five specimens each. Each specimen was disc shaped, flat of 32 mm diameter and 3 mm thickness. The samples were immersed in four disinfectant solutions: 2% Glutaraldehyde, 5% sodium hypochlorite, 0.05% iodophor, and 5.25% phenol for 10 min and 30 min, respectively. The control was without disinfection. Wettability of the samples was assessed by measuring the contact angle by using the Telescopic Goniometer. Data were subjected to analysis of variance (Fisher's test) and Tukey's post hoc test for multiple comparisons at 5% level of significance. The contact angle of 20.21° ± 0.22° were recorded in the control samples. After 10 min, the samples that were immersed in 5% sodium hypochlorite and 5.25% phenol showed significant statistical increase in the contact angle as compared to the control (P < 0.001). After 30 min of disinfection, only the samples immersed in 0.05% iodophor showed there were no significant changes in the contact angle, whereas the other disinfectants significantly increased the contact angle and decreased the wettability of the polyether material. Within the limitations of the study, 2% glutaraldehyde proved safe for 10 min of immersion disinfection while 0.05% iodophor holds promise as an effective disinfectant without affecting the wettability of the material.

Ceramic materials for porcelain veneers: part II. Effect of material, shade, and thickness on translucency.

PubMed

Barizon, Karine T L; Bergeron, Cathia; Vargas, Marcos A; Qian, Fang; Cobb, Deborah S; Gratton, David G; Geraldeli, Saulo

2014-10-01

Information regarding the differences in translucency among new ceramic systems is lacking. The purpose of this study was to compare the relative translucency of the different types of ceramic systems indicated for porcelain veneers and to evaluate the effect of shade and thickness on translucency. Disk specimens 13 mm in diameter and 0.7-mm thick were fabricated for the following 9 materials (n=5): VITA VM9, IPS Empress Esthetic, VITA PM9, Vitablocks Mark II, Kavo Everest G-Blank, IPS Empress CAD, IPS e.max CAD, IPS e.maxPress, and Lava Zirconia. VITA VM9 served as the positive control and Lava as the negative control. The disks were fabricated with the shade that corresponds to A1. For IPS e.maxPress, additional disks were made with different shades (BL2, BL4, A1, B1, O1, O2, V1, V2, V3), thickness (0.3 mm), and translucencies (high translucency, low translucency). Color coordinates (CIE L∗ a∗ b∗) were measured with a tristimulus colorimeter. The translucency parameter was calculated from the color difference of the material on a black versus a white background. One-way ANOVA, the post hoc Tukey honestly significant difference, and the Ryan-Einot-Gabriel-Welsch multiple range tests were used to analyze the data (α=.05). Statistically significant differences in the translucency parameter were found among porcelains (P<.001) according to the following rank: VM9>PM9, Empress Esthetic>Empress CAD>Mark II, Everest, e.max CAD>e.max Press>Lava. Significant differences also were noted when different shades and thickness were compared (P<.001). Different ceramic systems designed for porcelain veneers present varying degrees of translucency. The thickness and shade of lithium disilicate ceramic affect its translucency. Shade affects translucency parameter less than thickness. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

High strain rate and quasi-static tensile behaviour of Ti-6Al-4V after cyclic damage

NASA Astrophysics Data System (ADS)

Galán López, J.; Verleysen, P.; Degrieck, J.

2012-08-01

It is common that energy absorbing structural elements are subjected to a number of loading cycles before a crash event. Several studies have shown that previous fatigue can significantly influence the tensile properties of some materials, and hence the behaviour of structural elements made of them. However, when the capacity of absorbing energy of engineering materials is determined, fresh material without any fatigue damage is most often used. This study investigates the effect of fatigue damage on the dynamic tensile properties of Ti-6Al-4V in thin-sheet form. Results are completed with tests at quasi-static strain rates and observations of the fracture surfaces, and compared with results obtained from other alloys and steel grades. The experiments show that the dynamic properties of Ti-6Al-4V are not affected by a number of fatigue loading cycles high enough to significantly reduce the energy absorbing capabilities of EDM machined samples.

Experimental Study on the Interaction Between Contacting Barrier Materials for Containment of Radioactive Wastes

NASA Astrophysics Data System (ADS)

Huang, W. H.; Chang, H. C.

2017-12-01

The disposal of low- and intermediate-level radioactive wastes requires use of multi-barriers for isolation of the wastes from the biosphere. Typically, the engineered barriers are composed of a concrete vault, buffer and backfill materials. Zhishin clay and Black Hill bentonite were used as raw clay material in making buffer and backfill materials in this study. These clays were compacted to make buffer material, or mixed with Taitung area argillite to produce backfill material for potential application as barriers for the disposal of low- and intermediate-level radioactive wastes. The interaction between concrete barrier and the buffer/backfill material is simulated by an accelerated migration test to investigate the effect of contacting concrete on the expected functions of buffer/backfill material. The results show buffer material close to the contact with concrete exhibits significant change in the ratio of calcium/sodium exchange capacity, due to the move of calcium ions released from the concrete. The shorter the distance from the contacting interface, the ratio of the calcium/sodium concentration in buffer/backfill materials increases. The longer the distance from the interface, the effect of the contact on alteration in clays become less significant. Also, some decreases in swelling capacity in the buffer/backfill material near the concrete-backfill interface are noted. Finally, a comparison is made between Zhisin clay and Balck Hill bentonite on the interaction between concrete and the two clays. Black Hill bentonite was found to be influenced more by the interaction, because of the higher content of montmorillonite. On the other hand, being a mixture of clay and sand, backfill material is less affected by the decalsification of concrete at the contact than buffer material.

Polishing performance of multiple-use silicone rubber-based polishing instruments with and without disinfection/sterilization.

PubMed

Heintze, Siegward Dietmar; Forjanic, Monika

2008-10-01

To evaluate the effect of the multiple-use of a three-step rubber-based polishing system on the polishing performance with and without a disinfection/sterilization protocol with prolonged disinfection (overnight). The three-step polishing system Astropol was applied under standardized contact pressure of 2 N on 320 grit pre-roughened flat composite specimens of Tetric EvoCeram for 10 seconds (F and P disc) and 30 seconds (HP disc) respectively. After each polishing step, the surface gloss and roughness were measured with a glossmeter and an optical sensor (FRT MicroProf), respectively. Material loss of the composite specimens and polishing instruments were measured after each step with a high precision digital scale. For all four variables (surface gloss, surface roughness, composite loss, loss of rubber material) the mean percentage of change compared to the reference was calculated. Already after the first use, the instruments which were used without disinfection or sterilization demonstrated a statistically significantly reduced polishing performance in all polishing steps compared to the reference (new polishing system) (t-test, P < 0.05). In addition, this loss in performance further increased with the second and third re-use. Especially the third component (Astropol HP) was affected by performance loss. By contrast, the multiple-use of the instruments which were subjected to prolonged disinfection did not result in a reduced polishing performance. For the P disc, a statistically significant improvement of the polishing performance could be observed throughout almost all multiple-use sessions (ANOVA, P < 0.05). The improved polishing performance was, however, accompanied by an increased loss of the silicone rubber material of the P and F polishing discs; the HP discs were not affected by this loss. Furthermore, particles of the rubber material also adhered to the composite. The polishing performance of the discs which were only subjected to the sterilization process was not statistically significantly different to the polishing performance of the control group in terms of surface roughness; but the surface gloss was worse than that of the control group. No loss of rubber material or adherence to the composite was observed in this group.

Effect of bleaching on microhardness of esthetic restorative materials.

PubMed

Malkondu, Özlem; Yurdagüven, Haktan; Say, Esra Can; Kazazoğlu, Ender; Soyman, Mübin

2011-01-01

This study evaluated the effect of a high-concentration carbamide peroxide–containing home bleaching system (Opalescence PF) and a hydrogen peroxide–containing over-the-counter bleaching system (Treswhite Supreme) on the microhardness of two nanocomposites (Filtek Supreme XT and Premise) and leucite-reinforced glass ceramic (Empress Esthetic), glass ceramic (Empress 2 layering), and feldspathic porcelain (Matchmaker MC). A total of 100 specimens, 20 of each kind of the restorative materials, 2 mm in thickness and 10 mm in diameter, were fabricated. Then the specimens were polished with SiC paper and 1 μm alumina polishing paste. After polishing, porcelain specimens were glazed in accordance with the manufacturer's instructions. Each type of restorative material was then randomly divided into two groups (n=10), and the specimens were treated with either Opalescence PF or Treswhite Supreme. The microhardness of the specimens before bleaching (baseline) and after bleaching was determined using a digital microhardness tester. Data were analyzed using the Mann-Whitney U-test and the Wilcoxon test. Opalescence PF significantly influenced the hardness of all the restorative materials. Statistically significant decreases with respect to before bleaching were found for Premise (p=0.005), Empress Esthetic (p=0.003), Empress 2 layering (p=0.005), and Matchmaker-MC (p=0.003), whereas a statistically significant increase was observed in Filtek Supreme XT (p=0.028). The difference in the microhardness values between before and after bleaching using Treswhite Supreme was statistically significant only for Premise (p=0.022). High-concentration carbamide peroxide–containing home bleaching may affect the microhardness of restorative materials.

Information or resolution: Which is required from an SEM to study bulk inorganic materials?: Evaluate SEMs’ practical performance

DOE PAGES

Xing, Q.

2016-07-11

Significant technological advances in scanning electron microscopy (SEM) have been achieved over the past years. Different SEMs can have significant differences in functionality and performance. This work presents the perspectives on selecting an SEM for research on bulk inorganic materials. Understanding materials demands quantitative composition and orientation information, and informative and interpretable images that reveal subtle differences in chemistry, orientation/structure, topography, and electronic structure. The capability to yield informative and interpretable images with high signal-to-noise ratios and spatial resolutions is an overall result of the SEM system as a whole, from the electron optical column to the detection system. Themore » electron optical column determines probe performance. The roles of the detection system are to capture, filter or discriminate, and convert signal electrons to imaging information. The capability to control practical operating parameters including electron probe size and current, acceleration voltage or landing voltage, working distance, detector selection, and signal filtration is inherently determined by the SEM itself. As a platform for various accessories, e.g. an energydispersive spectrometer and an electron backscatter diffraction detector, the properties of the electron optical column, specimen chamber, and stage greatly affect the performance of accessories. Ease-of-use and ease-of-maintenance are of practical importance. It is practically important to select appropriate test specimens, design suitable imaging conditions, and analyze the specimen chamber geometry and dimensions to assess the overall functionality and performance of an SEM. Finally, for an SEM that is controlled/operated with a computer, the stable software and user-friendly interface significantly affect the usability of the SEM.« less

Information or resolution: Which is required from an SEM to study bulk inorganic materials?: Evaluate SEMs’ practical performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xing, Q.

Significant technological advances in scanning electron microscopy (SEM) have been achieved over the past years. Different SEMs can have significant differences in functionality and performance. This work presents the perspectives on selecting an SEM for research on bulk inorganic materials. Understanding materials demands quantitative composition and orientation information, and informative and interpretable images that reveal subtle differences in chemistry, orientation/structure, topography, and electronic structure. The capability to yield informative and interpretable images with high signal-to-noise ratios and spatial resolutions is an overall result of the SEM system as a whole, from the electron optical column to the detection system. Themore » electron optical column determines probe performance. The roles of the detection system are to capture, filter or discriminate, and convert signal electrons to imaging information. The capability to control practical operating parameters including electron probe size and current, acceleration voltage or landing voltage, working distance, detector selection, and signal filtration is inherently determined by the SEM itself. As a platform for various accessories, e.g. an energydispersive spectrometer and an electron backscatter diffraction detector, the properties of the electron optical column, specimen chamber, and stage greatly affect the performance of accessories. Ease-of-use and ease-of-maintenance are of practical importance. It is practically important to select appropriate test specimens, design suitable imaging conditions, and analyze the specimen chamber geometry and dimensions to assess the overall functionality and performance of an SEM. Finally, for an SEM that is controlled/operated with a computer, the stable software and user-friendly interface significantly affect the usability of the SEM.« less

The Effect of Food-Simulating Agents on the Bond Strength of Hard Chairside Reline Materials to Denture Base Resin.

PubMed

Fatemi, Farzaneh Sadat; Vojdani, Mahroo; Khaledi, Amir Ali Reza

2018-06-08

To investigate the influence of food-simulating agents on the shear bond strength between direct hard liners and denture base acrylic resin. In addition, mode of failure was evaluated. One hundred fifty cylindrical columns of denture base resin were fabricated and bonded to three types of hard reline materials (Hard GC Reline, Tokuyama Rebase II Fast, TDV Cold Liner Rebase). Specimens of each reline material were divided into five groups (n = 10) to undergo 12-day immersion in distilled water, 0.02 N citric acid aqueous solution, heptane, and 40% ethanol/water solution at 37°C. The control group was not immersed in any solution. The shear bond strength test was performed, and the failure mode was determined. Statistics were analyzed with two-way ANOVA and chi-square test (α = 0.05). Significant interaction was found between the hard liners and food simulating agents (p < 0.001). The shear bond strength of Tokuyama in 40% ethanol and TDV in heptane decreased significantly (p = 0.001, p < 0.001 respectively); however, none of the solutions could significantly affect the shear bond strength of Hard GC Reline (p = 0.208). The mixed failure mode occurred more frequently in Hard GC Reline compared with the other liners (p < 0.001) and was predominant in specimens with higher bond strength values (p = 0.012). Food simulating agents did not adversely affect the shear bond strength of Hard GC Reline; however, ethanol and heptane decreased the bond strength of Tokuyama and TDV, respectively. These findings may provide support to dentists to recommend restricted consumption of some foods and beverages for patients who have to use dentures relined with certain hard liners. © 2018 by the American College of Prosthodontists.

In vitro wear rates of materials under different loads and varying pH.

PubMed

Shabanian, Mitra; Richards, Lindsay C

2002-06-01

Despite the need for information about the wear characteristics of restorative materials, there have been few systemic studies of the factors that influence the rate of material wear. This study compared the wear rates of enamel and 3 tooth-colored restorative materials under different loads (0, 3.2, 6.7, and 9.95 kg) and pH levels (1.2, 3.3, and 7.0). An electromechanical tooth wear machine was used so that standard restorations representing 3 materials could be worn by opposing enamel under controlled conditions. The wear rates of enamel, composite (Z100), a conventional glass ionomer cement (Fuji IX), and a resin-modified glass ionomer cement (Fuji II LC) were compared at a range of loads (0 to 9.95 kg) and pH levels (1.2 to 7.0) and also at different sites across each restoration. Ten specimens were randomly assigned to each experimental group. Wear assessment was performed with a modified light microscope to quantify the height changes at defined points across wear facets. Four-way analysis of variance was used to compare wear rates among materials, pH levels, loads, and sites. Post-hoc t tests identified significant differences between specific pairs of experimental conditions (P<.05). The wear rates of enamel and the other test materials varied significantly with pH (P<.0001), load (P<.0001), and type of material (P<.0001). Enamel wear was influenced most by varied pH, whereas the composite was least affected by acid. The conventional glass ionomer cement was more susceptible than the composite to the effects of varied pH; the acid susceptibility of the resin-modified glass ionomer cement was generally between that of the composite and conventional glass ionomer cement. Enamel and the conventional glass ionomer cement were affected similarly by load. The composite was more resistant than the conventional glass ionomer cement to wear at higher loads; the resin-modified glass ionomer cement exhibited intermediate load resistance. Within the limitations of this study, the 3 test materials were more resistant than enamel to acid, with the composite demonstrating the lowest susceptibility to acid. The acid- and load-resistance of the resin-modified glass ionomer cement was consistently less than that of the composite and greater than that of the conventional glass ionomer cement.

Effects of implantation method and temperature on mortality and loss of simulated transmitters in hybrid striped bass

USGS Publications Warehouse

Walsh, M.G.; Bjorgo, K.A.; Isely, J.J.

2000-01-01

To determine the effects of surgical implantation method and temperature on mortality and transmitter loss, we compared two antenna placements (trailing antenna versus shielded needle) and two suture materials (absorbable versus nonabsorbable) in hybrid striped bass Morone saxitilis x Morone chrysops (227-410 mm total length) that had been surgically implanted with simulated transmitters and held at high (22-29??C) and low (12-18??C) temperatures for 120 d. Fish were individually examined after 7, 30, 60. 90. and 120 d to evaluate suture and wound condition as well as transmitter loss. Neither suture material nor antenna placement affected transmitter loss, mortality, or growth at either high or low temperatures. Absorbable sutures were lost more quickly than were nonabsorbable sutures, but they persisted beyond incision closure at both high and low temperatures. At high temperatures, 50% suture loss occurred by 30 d for absorbable sutures and by 60 d for nonabsorbable sutures. Mortality occurred only at high temperatures but was delayed and was likely caused by peritoneal infection. Transmitter loss was not significant; it occurred only in the low-temperature trial and was caused by pressure necrosis at the incision rather than by suture failure. Temperature significantly affected all responses examined in this study. Significant irritation, infection, and mortality occurred in all treatment groups at high temperatures.

7 CFR 42.102 - Definitions, general.

Code of Federal Regulations, 2011 CFR

2011-01-01

... freedom from defects which affect the serviceability, including appearance as well as usability, of the..., the usability of the container for its intended purpose. (b) Major defect. A defect that materially affects, or is likely to materially affect, the usability of the container for its intended purpose. (c...

7 CFR 42.102 - Definitions, general.

Code of Federal Regulations, 2013 CFR

2013-01-01

... freedom from defects which affect the serviceability, including appearance as well as usability, of the..., the usability of the container for its intended purpose. (b) Major defect. A defect that materially affects, or is likely to materially affect, the usability of the container for its intended purpose. (c...

7 CFR 42.102 - Definitions, general.

Code of Federal Regulations, 2012 CFR

2012-01-01

... freedom from defects which affect the serviceability, including appearance as well as usability, of the..., the usability of the container for its intended purpose. (b) Major defect. A defect that materially affects, or is likely to materially affect, the usability of the container for its intended purpose. (c...

Feasibility of Two Educational Methods for Teaching New Mothers: A Pilot Study

PubMed Central

Eckert, Diane; Smith, Frances; Stikes, Reetta; Rushton, Jeff; Myers, John; Capps, Joshua; Sparks, Kathryn

2015-01-01

Background Printed health educational materials are commonly issued to prepare patients for hospital discharge. Teaching methods that engage multiple senses have been shown to positively affect learning outcomes, suggesting that paper materials may not be the most effective approach when educating new mothers. In addition, many written patient educational materials do not meet national health literacy guidelines. Videos that stimulate visual and auditory senses provide an alternative, potentially more effective, strategy for delivering health information. The acceptability of these methods, as perceived by nurses executing patient education initiatives, is important for determining the most appropriate strategy. Objective The purpose of this study was to determine the feasibility of 2 educational methods for teaching new mothers how to care for themselves and their infants after hospital discharge. Feasibility was measured by adequate enrollment, acceptability of the intervention to patients and nurses, and initial efficacy. Methods New mothers (n=98) on a Mother-Baby Unit received health information focused on self-care and infant care delivered as either simple printed materials or YouTube videos on an iPad. Mothers completed a pretest, post-test, and an acceptability survey. Following completion of the initiative, nurses who participated in delivering the health education using one of these 2 methods were asked to complete a survey to determine their satisfaction with and confidence in using the materials. Results Mothers, on average, were 26 years old; 72% had a high school education; and 41% were African American. The improvement in knowledge scores was significantly higher for the iPad group (8.6% vs 4.4%, P=.02) compared to the pamphlet group. Group (B=4.81, P=.36) and time (B=6.12, P<.001) significantly affected scores, while no significant interaction effect was observed (B=5.69, P=.09). There were no significant differences in responses between the groups (all P values >.05). The nurses had a mean age of 44.3 years (SD 13.9) and had, on average, 16.6 years of experience (SD 13.8). The nurses felt confident and satisfied administering both educational modalities. Conclusions The pamphlet and iPad were identified as feasible and acceptable modalities for educating new mothers about self-care and infant care, though the iPad was more effective in improving knowledge. Understanding the acceptability of different teaching methods to patient educators is important for successful delivery of informational materials at discharge. PMID:26449647

Factors affecting the perception of whole-body vibration of occupational drivers: an analysis of posture and manual materials handling and musculoskeletal disorders

PubMed Central

Raffler, Nastaran; Ellegast, Rolf; Kraus, Thomas; Ochsmann, Elke

2016-01-01

Due to the high cost of conducting field measurements, questionnaires are usually preferred for the assessment of physical workloads and musculoskeletal disorders (MSDs). This study compares the physical workloads of whole-body vibration (WBV) and awkward postures by direct field measurements and self-reported data of 45 occupational drivers. Manual materials handling (MMH) and MSDs were also investigated to analyse their effect on drivers' perception. Although the measured values for WBV exposure were very similarly distributed among the drivers, the subjects' perception differed significantly. Concerning posture, subjects seemed to estimate much better when the difference in exposure was significantly large. The percentage of measured awkward trunk and head inclination were significantly higher for WBV-overestimating subjects than non-overestimators; 77 and 80% vs. 36 and 33%. Health complaints in terms of thoracic spine, cervical spine and shoulder–arm were also significantly more reported by WBV-overestimating subjects (42, 67, 50% vs. 0, 25, 13%, respectively). Although more MMH was reported by WBV-overestimating subjects, there was no statistical significance in this study. PMID:26114619

Olfactory Context-Dependent Memory and the Effects of Affective Congruency.

PubMed

Hackländer, Ryan P M; Bermeitinger, Christina

2017-10-31

Odors have been claimed to be particularly effective mnemonic cues, possibly because of the strong links between olfaction and emotion processing. Indeed, past research has shown that odors can bias processing towards affectively congruent material. In order to determine whether this processing bias translates to memory, we conducted 2 olfactory-enhanced-context memory experiments where we manipulated affective congruency between the olfactory context and to-be-remembered material. Given the presumed importance of valence to olfactory perception, we hypothesized that memory would be best for affectively congruent material in the olfactory enhanced context groups. Across the 2 experiments, groups which encoded and retrieved material in the presence of an odorant exhibited better memory performance than groups that did not have the added olfactory context during encoding and retrieval. While context-enhanced memory was exhibited in the presence of both pleasant and unpleasant odors, there was no indication that memory was dependent on affective congruency between the olfactory context and the to-be-remembered material. While the results provide further support for the notion that odors can act as powerful contextual mnemonic cues, they call into question the notion that affective congruency between context and focal material is important for later memory performance. © The Author 2017. Published by Oxford University Press. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Strength and microstructure of IPS Empress 2 glass-ceramic after different treatments.

PubMed

Oh, S C; Dong, J K; Lüthy, H; Schärer, P

2000-01-01

This investigation was designed to determine whether heat pressing and/or simulated heat treatments affect the flexure strength and microstructure of the lithium disilicate glass-ceramic of the IPS Empress 2 system. Four groups of the lithium disilicate glass-ceramic were prepared as follows: group 1 = as-received material; group 2 = heat-pressed material; group 3 = heat-pressed and stimulated initial heat-treated material; and group 4 = heat-pressed and simulated heat-treated material with full firings for a final restoration. Three-point bending tests and scanning electron microscopy (SEM) analysis were conducted. The flexure strength of group 2 was significantly higher than that of group 1. However, there were no significant differences in strength among groups 2, 3, and 4, or between groups 1 and 4. The SEM micrographs of the lithium disilicate glass-ceramic showed a closely packed, multidirectionally interlocking microstructure of numerous lithium disilicate crystals protruding from the glass matrix. The crystals in the glass matrix of the heat-pressed materials (groups 2, 3, and 4) were a little more homogeneous and about 2 times bigger than those of the as-received material (group 1). These changes of the microstructure were greatest between groups 1 and 2. However, there were no marked differences among groups 2, 3, and 4. Although there were significant increases in the strength and some changes of the microstructure after the heat-pressing operation, the combination of heat pressing and simulated subsequent heat treatments did not produce an increase of strength of IPS Empress 2 glass-ceramic.

Aging and the Haptic Perception of Material Properties.

PubMed

Norman, J Farley; Adkins, Olivia C; Hoyng, Stevie C; Dowell, Catherine J; Pedersen, Lauren E; Gilliam, Ashley N

2016-12-01

The ability of 26 younger (mean age was 22.5 years) and older adults (mean age was 72.6 years) to haptically perceive material properties was evaluated. The participants manually explored (for 5 seconds) 42 surfaces twice and placed each of these 84 experimental stimuli into one of seven categories: paper, plastic, metal, wood, stone, fabric, and fur/leather. In general, the participants were best able to identify fur/leather and wood materials; in contrast, recognition performance was worst for stone and paper. Despite similar overall patterns of performance for younger and older participants, the younger adults' recognition accuracies were 26.5% higher. The participants' tactile acuities (assessed by tactile grating orientation discrimination) affected their ability to identify surface material. In particular, the Pearson r correlation coefficient relating the participants' grating orientation thresholds and their material identification performance was -0.8: The higher the participants' thresholds, the lower the material recognition ability. While older adults are able to effectively perceive the solid shape of environmental objects using the sense of touch, their ability to perceive surface materials is significantly compromised.

A Bibliography of Affective Materials for the Adolescent Years.

ERIC Educational Resources Information Center

Bolen, Jackie

The annotated bibliography lists approximately 146 instructional materials and books useful to teachers who deal with normal and abnormal adolescent affective behavior in junior and senior high schools. An explanation sheet gives instructions for correlating publisher with a specific material, and for finding items according to topic categories. A…

Gloss and Stain Resistance of Ceramic-Polymer CAD/CAM Restorative Blocks.

PubMed

Lawson, Nathaniel C; Burgess, John O

2016-03-01

To evaluate the gloss and stain resistance of several new ceramic-polymer CAD/CAM blocks Specimens (4 mm) were sectioned from: Enamic (polymer-infused ceramic), LAVA Ultimate (nano-ceramic reinforced polymer), e.max (lithium disilicate), Paradigm C (porcelain), and Paradigm MZ100 (composite). Specimens were wet polished on a polishing wheel to either 320 grit silicon paper (un-polished, N = 8) or 2000 grit silicon carbide papers followed by a 0.05 μm alumina slurry (polished, N = 8). Initial gloss and color (L*a*b*) values were measured. Specimens were stored in a staining solution at 37°C in darkness for 12 days (simulating 1 year). After storage, L*a*b* values re-measured. Change in color was reported as ΔE00 based on the CIEDE2000 formula. Gloss and ΔE00 were analyzed by two-way analysis of variance (ANOVA) (alpha = .05). Separate one-way ANOVA and Tukey post-hoc analyses were performed for both polish conditions and all materials. Two-way ANOVA showed that factors material, polish and their interaction were significant for both gloss and ΔE00 (p < .01). Post-hoc analysis reveals that polished specimens had significantly less color change than un-polished specimens for Paradigm C and LAVA Ultimate. E.max had significantly higher gloss and less color change than all other materials. The composition and polish of CAD/CAM materials affects gloss and stain resistance. Ceramic-polymer hybrid materials can achieve the high gloss required for esthetic restorations. These materials should be polished in order to minimize staining. If polished, all of the tested materials exhibited clinically acceptable color changes at 1 year of simulated staining. (J Esthet Restor Dent 28:S40-S45, 2016). © 2015 Wiley Periodicals, Inc.

Niobium pentoxide as radiopacifying agent of calcium silicate-based material: evaluation of physicochemical and biological properties.

PubMed

Silva, Guilherme F; Tanomaru-Filho, Mário; Bernardi, Maria I B; Guerreiro-Tanomaru, Juliane M; Cerri, Paulo S

2015-11-01

The physicochemical properties and the tissue reaction promoted by microparticulated or nanoparticulated niobium pentoxide (Nb2O5) added to calcium silicate-based cement (CS), compared to MTA-Angelus™, were evaluated. Materials were submitted to the tests of radiopacity, setting time, pH, and calcium ion release. Polyethylene tubes filled with the materials were implanted into rats subcutaneously. After 7, 15, 30, and 60 days, the specimens were fixed and embedded in paraffin. Hematoxylin & eosin (H&E)-stained sections were used to compute the number of inflammatory cells (IC). Interleukin-6 (IL-6) detection was performed, and the number of immunolabeled cells was obtained; von Kossa method was also carried out. Data were subjected to ANOVA and Tukey test (p ≤ 0.05). Nb2O5micro and Nb2O5nano provided to the CS radiopacity values (3.52 and 3.75 mm Al, respectively) superior to the minimum recommended. Groups containing Nb2O5 presented initial setting time significantly superior than mineral trioxide aggregate (MTA). All materials presented an alkaline pH and released calcium ions. The number of IC and IL-6 immunolabeled cells in the CS + Nb2O5 groups was significantly reduced in comparison to MTA in all periods. von Kossa-positive structures were observed adjacent to implanted materials in all periods. The addition of Nb2O5 to the CS resulted in a material biocompatible and with adequate characteristics regarding radiopacity and final setting time and provides an alkaline pH to the environment. Furthermore, the particle size did not significantly affect the physicochemical and biological properties of the calcium silicate-based cement. Niobium pentoxide can be used as radiopacifier for the development of calcium silicate-based materials.

Effect of different impression materials and techniques on the dimensional accuracy of implant definitive casts.

PubMed

Ebadian, Behnaz; Rismanchian, Mansor; Dastgheib, Badrosadat; Bajoghli, Farshad

2015-01-01

Different factors such as impression techniques and materials can affect the passive fit between the superstructure and implant. The aim of this study was to determine the effect of different impression materials and techniques on the dimensional accuracy of implant definitive casts. Four internal hex implants (Biohorizons Ø4 mm) were placed on a metal maxillary model perpendicular to the horizontal plane in maxillary lateral incisors, right canine and left first premolar areas. Three impression techniques including open tray, closed tray using ball top screw abutments and closed tray using short impression copings and two impression materials (polyether and polyvinyl siloxane) were evaluated (n = 60). The changes in distances between implant analogues in mediolateral (x) and anteroposterior (y) directions and analogue angles in x/z and y/z directions in the horizontal plane on the definitive casts were measured by coordinate measuring machine. The data were analyzed by multivariate two-way analysis of variance and one sample t-test (α = 0.05). No statistical significant differences were observed between different impression techniques and materials. However, deviation and distortion of definitive casts had a significant difference with the master model when short impression copings and polyvinyl siloxane impression material were used (P < 0.05). In open tray technique, there was a significant difference in the rotation of analogs compared with the master model with both impression materials (P < 0.05). There was no difference between open and closed tray impression techniques; however, less distortion and deviation were observed in the open tray technique. In the closed tray impression technique, ball top screw was more accurate than short impression copings.

Triglycidylamine Crosslinking of Porcine Aortic Valve Cusps or Bovine Pericardium Results in Improved Biocompatibility, Biomechanics, and Calcification Resistance

PubMed Central

Connolly, Jeanne M.; Alferiev, Ivan; Clark-Gruel, Jocelyn N.; Eidelman, Naomi; Sacks, Michael; Palmatory, Elizabeth; Kronsteiner, Allyson; DeFelice, Suzanne; Xu, Jie; Ohri, Rachit; Narula, Navneet; Vyavahare, Narendra; Levy, Robert J.

2005-01-01

We investigated a novel polyepoxide crosslinker that was hypothesized to confer both material stabilization and calcification resistance when used to prepare bioprosthetic heart valves. Triglycidylamine (TGA) was synthesized via reacting epichlorhydrin and NH3. TGA was used to crosslink porcine aortic cusps, bovine pericardium, and type I collagen. Control materials were crosslinked with glutaraldehyde (Glut). TGA-pretreated materials had shrink temperatures comparable to Glut fixation. However, TGA crosslinking conferred significantly greater collagenase resistance than Glut pretreatment, and significantly improved biomechanical compliance. Sheep aortic valve interstitial cells grown on TGA-pretreated collagen did not calcify, whereas sheep aortic valve interstitial cells grown on control substrates calcified extensively. Rat subdermal implants (porcine aortic cusps/bovine pericardium) pretreated with TGA demonstrated significantly less calcification than Glut pretreated implants. Investigations of extracellular matrix proteins associated with calcification, matrix metalloproteinases (MMPs) 2 and 9, tenascin-C, and osteopontin, revealed that MMP-9 and tenascin-C demonstrated reduced expression both in vitro and in vivo with TGA crosslinking compared to controls, whereas osteopontin and MMP-2 expression were not affected. TGA pretreatment of heterograft biomaterials results in improved stability compared to Glut, confers biomechanical properties superior to Glut crosslinking, and demonstrates significant calcification resistance. PMID:15631995

Absorption Of Crushing Energy In Square Composite Tubes

NASA Technical Reports Server (NTRS)

Farley, Gary L.

1992-01-01

Report describes investigation of crash-energy-absorbing capabilities of square-cross-section tubes of two matrix/fiber composite materials. Both graphite/epoxy and Kevlar/epoxy tubes crushed in progressive and stable manner. Ratio between width of cross section and thickness of wall determined to affect energy-absorption significantly. As ratio decreases, energy-absorption capability increases non-linearly. Useful in building energy-absorbing composite structures.

Correlation of microstructure and thermo-mechanical properties of a novel hydrogen transport membrane

NASA Astrophysics Data System (ADS)

Zhang, Yongjun

A key part of the FutureGen concept is to support the production of hydrogen to fuel a "hydrogen economy," with the use of clean burning hydrogen in power-producing fuel cells, as well as for use as a transportation fuel. One of the key technical barriers to FutureGen deployment is reliable and efficient hydrogen separation technology. Most Hydrogen Transport Membrane (HTM) research currently focuses on separation technology and hydrogen flux characterization. No significant work has been performed on thermo-mechanical properties of HTMs. The objective of the thesis is to understand the structure-property correlation of HTM and to characterize (1) thermo mechanical properties under different reducing environments and thermal cycles (thermal shock), and (2) evaluate the stability of the novel HTM material. A novel HTM cermet bulk sample was characterized for its physical and mechanical properties at both room temperature and at elevated temperature up to 1000°C. Micro-structural properties and residual stresses were evaluated in order to understand the changing mechanism of the microstructure and its effects on the mechanical properties of materials. A correlation of the microstructural and thermo mechanical properties of the HTM system was established for both HTM and the substrate material. Mechanical properties of both selected structural ceramics and the novel HTM cermet bulk sample are affected mainly by porosity and microstructural features, such as grain size and pore size-distribution. The Young's Modulus (E-value) is positively correlated to the flexural strength for materials with similar crystallographic structure. However, for different crystallographic materials, physical properties are independent of mechanical properties. Microstructural properties, particularly, grain size and crystallographic structure, and thermodynamic properties are the main factors affecting the mechanical properties at both room and high temperatures. The HTM cermet behaves more like an elastic material at room temperature and as a ductile material at temperature above 850°C. The oxidation and the plasticity of Pd phase mainly affected the mechanical properties of HTM cermet at high temperature, also as a result of thermal cycling. Residual stress induced in the HTM by thermo cycles also plays a very critical role in defining the thermo-mechanical properties.

Biological Fuel Cells and Membranes.

PubMed

Ghassemi, Zahra; Slaughter, Gymama

2017-01-17

Biofuel cells have been widely used to generate bioelectricity. Early biofuel cells employ a semi-permeable membrane to separate the anodic and cathodic compartments. The impact of different membrane materials and compositions has also been explored. Some membrane materials are employed strictly as membrane separators, while some have gained significant attention in the immobilization of enzymes or microorganisms within or behind the membrane at the electrode surface. The membrane material affects the transfer rate of the chemical species (e.g., fuel, oxygen molecules, and products) involved in the chemical reaction, which in turn has an impact on the performance of the biofuel cell. For enzymatic biofuel cells, Nafion, modified Nafion, and chitosan membranes have been used widely and continue to hold great promise in the long-term stability of enzymes and microorganisms encapsulated within them. This article provides a review of the most widely used membrane materials in the development of enzymatic and microbial biofuel cells.

Cellulose acetate fibers prepared from different raw materials with rapid synthesis method.

PubMed

Chen, Jinghuan; Xu, Jikun; Wang, Kun; Cao, Xuefei; Sun, Runcang

2016-02-10

Transesterification is a mild process to prepare cellulose acetate (CA) as compared with the traditional method. In this study, CA fibers were produced from six cellulose raw materials based on a simple and rapid transesterification method. The properties of the CA solutions and the obtained CA fibers were investigated in detail. Results showed that all of the cellulose raw materials were esterified within 15 min, and spinning dopes could be obtained by concentrating the CA solutions via vacuum distillation. The XRD, FT-IR, (1)H, (13)C and HSQC NMR analysis confirmed the successful synthesis of CA. The degree of substitution (DS) of the obtained CA was significantly affected by the degree of polymerization (DP) of cellulose raw materials, which further influenced the viscosity of CA solutions as well as the structural, thermal and mechanical properties of the CA fibers. Copyright © 2015 Elsevier Ltd. All rights reserved.

Biological Fuel Cells and Membranes

PubMed Central

Ghassemi, Zahra; Slaughter, Gymama

2017-01-01

Biofuel cells have been widely used to generate bioelectricity. Early biofuel cells employ a semi-permeable membrane to separate the anodic and cathodic compartments. The impact of different membrane materials and compositions has also been explored. Some membrane materials are employed strictly as membrane separators, while some have gained significant attention in the immobilization of enzymes or microorganisms within or behind the membrane at the electrode surface. The membrane material affects the transfer rate of the chemical species (e.g., fuel, oxygen molecules, and products) involved in the chemical reaction, which in turn has an impact on the performance of the biofuel cell. For enzymatic biofuel cells, Nafion, modified Nafion, and chitosan membranes have been used widely and continue to hold great promise in the long-term stability of enzymes and microorganisms encapsulated within them. This article provides a review of the most widely used membrane materials in the development of enzymatic and microbial biofuel cells. PMID:28106711

Ultrasonic monitoring of the setting of silicone elastomeric impression materials.

PubMed

Kanazawa, Tomoe; Murayama, Ryosuke; Furuichi, Tetsuya; Imai, Arisa; Suda, Shunichi; Kurokawa, Hiroyasu; Takamizawa, Toshiki; Miyazaki, Masashi

2017-01-31

This study used an ultrasonic measurement device to monitor the setting behavior of silicone elastomeric impression materials, and the influence of temperature on setting behavior was determined. The ultrasonic device consisted of a pulser-receiver, transducers, and an oscilloscope. The two-way transit time through the mixing material was divided by two to account for the down-and-back travel path; then it was multiplied by the sonic velocity. Analysis of variance and the Tukey honest significant difference test were used. In the early stages of the setting process, most of the ultrasonic energy was absorbed by the elastomers and the second echoes were relatively weak. As the elastomers hardened, the sonic velocities increased until they plateaued. The changes in sonic velocities varied among the elastomers tested, and were affected by temperature conditions. The ultrasonic method used in this study has considerable potential for determining the setting processes of elastomeric impression materials.

In Vitro Biocompatibility and Endothelialization of Novel Magnesium-Rare Earth Alloys for Improved Stent Applications

PubMed Central

Zhao, Nan; Watson, Nevija; Xu, Zhigang; Chen, Yongjun; Waterman, Jenora; Sankar, Jagannathan; Zhu, Donghui

2014-01-01

Magnesium (Mg) based alloys are the most advanced cardiovascular stent materials. This new generation of stent scaffold is currently under clinical evaluation with encouraging outcomes. All these Mg alloys contain a certain amount of rare earth (RE) elements though the exact composition is not yet disclosed. RE alloying can usually enhance the mechanical strength of different metal alloys but their toxicity might be an issue for medical applications. It is still unclear how RE elements will affect the magnesium (Mg) alloys intended for stent materials as a whole. In this study, we evaluated MgZnCaY-1RE, MgZnCaY-2RE, MgYZr-1RE, and MgZnYZr-1RE alloys for cardiovascular stents applications regarding their mechanical strength, corrosion resistance, hemolysis, platelet adhesion/activation, and endothelial biocompatibility. The mechanical properties of all alloys were significantly improved. Potentiodynamic polarization showed that the corrosion resistance of four alloys was at least 3–10 times higher than that of pure Mg control. Hemolysis test revealed that all the materials were non-hemolytic while little to moderate platelet adhesion was found on all materials surface. No significant cytotoxicity was observed in human aorta endothelial cells cultured with magnesium alloy extract solution for up to seven days. Direct endothelialization test showed that all the alloys possess significantly better capability to sustain endothelial cell attachment and growth. The results demonstrated the promising potential of these alloys for stent material applications in the future. PMID:24921251

The impact of recurrent disasters on mental health: a study on seasonal floods in northern India.

PubMed

Wind, Tim R; Joshi, Pooran C; Kleber, Rolf J; Komproe, Ivan H

2013-06-01

Very little is known on the impact of recurrent disasters on mental health. Aim The present study examines the immediate impact of a recurrent flood on mental health and functioning among an affected population in the rural district of Bahraich, Uttar Pradesh, India, compared with a population in the same region that is not affected by floods. The study compared 318 affected respondents with 308 individuals who were not affected by floods. Symptoms of anxiety and depression were assessed by the Hopkins Symptom Checklist-25 (HSCL-25). Psychological and physical functioning was assessed by using the Short Form-12 (SF-12). The affected group showed large to very large differences with the comparison group on symptoms of anxiety (D = .92) and depression (D = 1.22). The affected group scored significantly lower on psychological and physical functioning than the comparison group (respectively D = .33 and D = .80). However, hierarchical linear regressions showed no significant relationship between mental health and the domains of functioning in the affected group, whereas mental health and the domains of functioning were significantly related in the comparison group. This study found a large negative impact of the recurrent floods on mental health outcomes and psychological and physical functioning. However, in a context with recurrent floods, disaster mental health status is not a relevant predictor of functioning. The findings suggest that the observed mental health status and impaired functioning in this context are also outcomes of another mechanism: Both outcomes are likely to be related to the erosion of the social and environmental and material context. As such, the findings refer to a need to implement psychosocial context-oriented interventions to address the erosion of the context rather than specific mental health interventions.

Evaluation of 5 knots and 2 suture materials for arthroscopic rotator cuff repair: very strong sutures can still slip.

PubMed

Abbi, Gaurav; Espinoza, Luis; Odell, Timothy; Mahar, Andrew; Pedowitz, Robert

2006-01-01

To compare a standard suture material with a newer material using multiple arthroscopic knot configurations and to evaluate the biomechanical performance of a new sliding-locking knot compared with 4 surgical standards. Controlled laboratory study. Five knots were evaluated (Weston, Tennessee, Duncan, SMC, and the new San Diego knot) using 2 suture materials, No. 2 Ethibond (Ethicon, Somerville, NJ) or No. 2 Fiberwire (Arthrex, Naples, FL). Eight samples were tested for each knot-suture configuration. Samples were pretensioned to 10 N and then loaded from 10 to 45 N for 1,000 cycles. Intact knots were loaded to failure. Fiberwire had significantly higher load-to-failure (276 +/- 24 N) compared with Ethibond (111 +/- 13 N) (P < .001), although there was no significant difference as a function of knot configuration. Of the 40 Fiberwire knots, 3 failed by early slippage during cyclic loading and 8 slipped at very low tension during load-to-failure. None of the Ethibond knots and none of the San Diego knots failed by early slippage. Surface characteristics and suture construction affect the tendency for knot slippage. Surgeons should understand the impact of handling characteristics, frictional properties, and ultimate failure load when selecting suture materials and knots for arthroscopic repair.

Modeling Strain Rate Effect of Heterogeneous Materials Using SPH Method

NASA Astrophysics Data System (ADS)

Ma, G. W.; Wang, X. J.; Li, Q. M.

2010-11-01

The strain rate effect on the dynamic compressive failure of heterogeneous material based on the smoothed particle hydrodynamics (SPH) method is studied. The SPH method employs a rate-insensitive elasto-plastic damage model incorporated with a Weibull distribution law to reflect the mechanical behavior of heterogeneous rock-like materials. A series of simulations are performed for heterogeneous specimens by applying axial velocity conditions, which induce different strain-rate loadings to the specimen. A detailed failure process of the specimens in terms of microscopic crack-activities and the macro-mechanical response are discussed. Failure mechanisms between the low and high strain rate cases are compared. The result shows that the strain-rate effects on the rock strength are mainly caused by the changing internal pressure due to the inertial effects as well as the material heterogeneity. It also demonstrates that the inertial effect becomes significant only when the induced strain rate exceeds a threshold, below which, the dynamic strength enhancement can be explained due to the heterogeneities in the material. It also shows that the dynamic strength is affected more significantly for a relatively more heterogeneous specimen, which coincides with the experimental results showing that the poor quality specimen had a relatively larger increase in the dynamic strength.

Linear Dimensional Stability of Irreversible Hydrocolloid Materials Over Time.

PubMed

Garrofé, Analía B; Ferrari, Beatriz A; Picca, Mariana; Kaplan, Andrea E

2015-12-01

The aim of this study was to evaluate the linear dimensional stability of different irreversible hydrocolloid materials over time. A metal mold was designed with custom trays made of thermoplastic sheets (Sabilex, sheets 0.125 mm thick). Perforations were made in order to improve retention of the material. Five impressions were taken with each of the following: Kromopan 100 (LASCOD) [AlKr], which has dimensional stability of 100 hours, and Phase Plus (ZHERMACK) [AlPh], which has dimensional stability of 48 hours. Standardized digital photographs were taken at different time intervals (0, 15, 30, 45, 60, 120 minutes; 12, 24 and 96 hours), using an "ad-hoc" device. The images were analyzed with software (UTHSCSA Image Tool) by measuring the distance between intersection of the lines previously made at the top of the mold. The results were analyzed by ANOVA for repeated measures. Initial and final values were (mean and standard deviation): AlKr: 16.44 (0.22) and 16.34 (0.11), AlPh: 16.40 (0.06) and 16.18 (0.06). Statistical evaluation showed significant effect of material and time factors. Under the conditions in this study, time significantly affects the linear dimensional stability of irreversible hydrocolloid materials. Sociedad Argentina de Investigación Odontológica.

[Microvascular descompression for trigeminal neuralgia: prognostic [corrected] factors].

PubMed

Alberione, F; Arena, A; Matera, R

2008-06-01

We describe our experience of the MVD in the typical trigeminal neuralgia and identify the prognostic factors. A retrospective studio of 89 cases between 1995-2005 was used. The prognostic significant data evaluated were demographics data; duration of neuralgia; the affected divisions involved; surgical findings; used material for the decompression. The data analysis was made with the chi(2) test. We have found an excellent outcome in 77% one year later. The age and the antecedent of hypertension disease were not statistically significant. A poor outcome was observed for: female sex, neuralgia lasting longer than two years, the three divisions involved, venous compression and the muscle used as surgical material. The MVD is an effective and reliable technique. The use of muscle is not recommended. When the three trigeminal divisions are involved we should choose another technique.

Factors affecting activated carbon-based catalysts for selective hydrogen sulfide oxidation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Huixing; Monnell, J.D.; Alvin, M.A.

2008-09-01

The primary product of coal gasification processes is synthesis gas (syngas), a mixture of CO, H2, CO2, H2O and a number of minor components. Among the most significant minor components in syngas is hydrogen sulfide (H2S). In addition to its adverse environmental impact, H2S poisons the catalysts and hydrogen purification membranes, and causes severe corrosion in gas turbines. Technologies that can remove H2S from syngas and related process streams are, therefore, of considerable practical interest. To meet this need, we work towards understanding the mechanism by which prospective H2S catalysts perform in simulated fuel gas conditions. Specifically, we show thatmore » for low-temperature gas clean-up (~1408C) using activated carbon fibers and water plays a significant role in H2S binding and helps to prolong the lifetime of the material. Basic surface functional groups were found to be imperative for significant conversion of H2S to daughter compounds, whereas metal oxides (La and Ce) did little to enhance this catalysis. We show that although thermal regeneration of the material is possible, the regenerated material has a substantially lower catalytic and sorption capacity.« less

Strain-rate dependence of ramp-wave evolution and strength in tantalum

DOE PAGES

Lane, J. Matthew D.; Foiles, Stephen M.; Lim, Hojun; ...

2016-08-25

We have conducted molecular dynamics (MD) simulations of quasi-isentropic ramp-wave compression to very high pressures over a range of strain rates from 10 11 down to 10 8 1/s. Using scaling methods, we collapse wave profiles from various strain rates to a master profile curve, which shows deviations when material response is strain-rate dependent. Thus, we can show with precision where, and how, strain-rate dependence affects the ramp wave. We find that strain rate affects the stress-strain material response most dramatically at strains below 20%, and that above 30% strain the material response is largely independent of strain rate. Wemore » show good overall agreement with experimental stress-strain curves up to approximately 30% strain, above which simulated response is somewhat too stiff. We postulate that this could be due to our interatomic potential or to differences in grain structure and/or size between simulation and experiment. Strength is directly measured from per-atom stress tensor and shows significantly enhanced elastic response at the highest strain rates. As a result, this enhanced elastic response is less pronounced at higher pressures and at lower strain rates.« less

Effect of pin tool design on the material flow of dissimilar AA7075-AA6061 friction stir welds

NASA Astrophysics Data System (ADS)

Hasan, Mohammed M.; Ishak, M.; Rejab, M. R. M.

2017-10-01

Tool design is the most influential aspect in the friction stir welding (FSW) technology. Influence of pin tool geometry on material flow pattern are studied in this work during the FSW of dissimilar AA7075 and AA6061 aluminium alloys. Three truncated pin tool profiles (threaded, threaded with single flat, and unthreaded with single flat) were used to prepare the weldments. The workpieces were joined using a custom-made clamping system under 1100 rpm of spindle speed, 300 mm/min of traverse rate and 3° of tilt angle. The metallographic analysis showed that defect-free welds can be produced using the three pin tools with significant changes in the mixing stir zone structure. The results declared that the introducing of the flat on the cone of the probe deviates the pattern of the onion rings without changing the chemical composition of the created layers. This in turn improves the hardness distribution and tensile strength of the welded joint. It was also noted that both heat affected zone (HAZ) and thermal-mechanical affected zone (TMAZ) are similar in composition to their corresponding base materials (BM).

Effect of metallic silver nanoparticles on the alignment and relaxation behaviour of liquid crystalline material in smectic C* phase

NASA Astrophysics Data System (ADS)

Vimal, Tripti; Kumar Gupta, Swadesh; Katiyar, Rohit; Srivastava, Atul; Czerwinski, Michal; Krup, Katarzyna; Kumar, Sandeep; Manohar, Rajiv

2017-09-01

The influence of silver nanoparticles dispersed in a Ferroelectric Liquid Crystal (FLC) on the properties of the resultant composite system has been investigated by thermal, electro-optical, and dielectric methods. We show that the concentration of thiol capped silver nanoparticles is a critical factor in governing the alignment of nanoparticles (NPs) in the host FLC. The orientation of NPs in composite samples affects the ordering of the LC (Liquid Crystal) phase and consequently changes the various phase transition temperatures of the host LC. Formation of self-assembled 2D (two dimensional) arrays of nanoparticles is observed for high concentration of dopant in the LC, oriented perpendicular to the direction of rubbing. We propose that the molecular interaction between the thiol capped NPs and LC molecules is the key factor behind such an arrangement of NPs. Orientation of NPs has affected the relaxation behaviour and various other material parameters, significantly. A noteworthy change in DC conductivity articulates our proposed idea of the formation of 2D array of NPs perpendicular to the direction of rubbing. This comprehensive study endorses the importance of dopant concentration in modifying the properties of the host LC material.

Effects Of Thermal Exchange On Material Flow During Steel Thixoextrusion Process

NASA Astrophysics Data System (ADS)

Eric, Becker; Guochao, Gu; Laurent, Langlois; Raphaël, Pesci; Régis, Bigot

2011-01-01

Semisolid processing is an innovative technology for near net-shape production of components, where the metallic alloys are processed in the semisolid state. Taking advantage of the thixotropic behavior of alloys in the semisolid state, significant progress has been made in semisolid processing. However, the consequences of such behavior on the flow during thixoforming are still not completely understood. To explore and better understand the influence of the different parameters on material flow during thixoextrusion process, thixoextrusion experiments were performed using the low carbon steel C38. The billet was partially melted at high solid fraction. Effects of various process parameters including the initial billet temperature, the temperature of die, the punch speed during process and the presence of a Ceraspray layer at the interface of tool and billet were investigated through experiments and simulation. After analyzing the results thus obtained, it was identified that the aforementioned parameters mainly affect thermal exchanges between die and part. The Ceraspray layer not only plays a lubricant role, but also acts as a thermal barrier at the interface of tool and billet. Furthermore, the thermal effects can affect the material flow which is composed of various distinct zones.

Root morphology of several potato varieties - infected Meloidogyne spp. and addition of organic matters

NASA Astrophysics Data System (ADS)

Lubis, K.; Lubis, A. M.; Siregar, L. A. M.; Lisnawita; Safni, I.; Tantawi, A. R.

2018-02-01

This research was aimed to determine root morphology of several potato varieties which were applied by organic materials into the planting medium inoculated nematodes. The research was conducted at Research Station of Horticulture in Berastagi, Sumatera Utara on May to November 2016. The randomized block design was used with two factors; the first factor was K1 = Positive control (no use compost / inoculation of nematodes) K2 = Negative control (no use compost / no inoculation of nematodes) K3 = Using compost mucuna and inoculation of nematode, K4 = Using compost peanuts and inoculation of nematodes and the second factor was potato varieties (Tenggo, Maglia, and Margahayu). The results showed that organic matters increased the shoot fresh weight, the root fresh weight, the tubers weight and the number of tubers, root diameter, root lenght. However, organic matters also increased the number of nematodes. Varieties of Tenggo and Maglia showed significant affect to all observed characters. The interaction of the two treatments had significant affect to the shoot fresh weight, the number of root-knot, and the number of tubers, root lenght. However, no significant affect was observed in root wet weight, and tuber weight.

Controlling Mechanical Properties of Cell-Laden Hydrogels by Covalent Incorporation of Graphene Oxide

PubMed Central

Cha, Chaenyung; Shin, Su Ryon; Gao, Xiguang; Annabi, Nasim; Dokmeci, Mehmet R.; Tang, Xiaowu (Shirley); Khademhosseini, Ali

2013-01-01

Graphene-based materials are useful reinforcing agents to modify the mechanical properties of hydrogels. Here, we present an approach to covalently incorporate graphene oxide (GO) into hydrogels via radical copolymerization to enhance the dispersion and conjugation of GO sheets within the hydrogels. GO is chemically modified to present surface-grafted methacrylate groups (MeGO). In comparison to GO, higher concentrations of MeGO can be stably dispersed in a pre-gel solution containing methacrylated gelatin (GelMA) without aggregation or significant increase in viscosity. In addition, the resulting MeGO-GelMA hydrogels demonstrate a significant increase in fracture strength with increasing MeGO concentration. Interestingly, the rigidity of the hydrogels is not significantly affected by the covalently incorporated GO. Therefore, our approach can be used to enhance the structural integrity and resistance to fracture of the hydrogels without inadvertently affecting their rigidity, which is known to affect the behavior of encapsulated cells. The biocompatibility of MeGO-GelMA hydrogels is confirmed by measuring the viability and proliferation of the encapsulated fibroblasts. Overall, this study highlights the advantage of covalently incorporating GO into a hydrogel system, and improves the quality of cell-laden hydrogels. PMID:24127350

Effect of laser welding parameters on the austenite and martensite phase fractions of NiTi

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oliveira, J.P., E-mail: jp.oliveira@campus.fct.unl

Although laser welding is probably the most used joining technique for NiTi shape memory alloys there is still a lack of understanding about the effects of laser welding parameters on the microstructural induced changes: in both the heat affected and fusion zones martensite may be present, while the base material is fully austenitic. Synchrotron X-ray diffraction was used for fine probing laser welded NiTi joints. Through Rietveld refinement the martensite and austenite phase fractions were determined and it was observed that the martensite content increases towards the weld centreline. This is related to a change of the local transformation temperaturesmore » on these regions, which occurs due to compositional variation in those regions. The martensite phase fraction in the thermally affected regions may have significant implications on functional properties on these joints. - Highlights: •Synchrotron X-ray diffraction was used for fine probing of the microstructure in laser welded NiTi joints. •Rietveld refinement allowed to determine the content of martensite along the heat affected and fusion zones. •The martensite content increases from the base material towards the weld centreline.« less

Structure, magnetic, and electrical properties of Zn1-xMnxO material

NASA Astrophysics Data System (ADS)

Sebayang, P.; Hulu, S. F.; Nasruddin, Aryanto, D.; Kurniawan, C.; Subhan, A.; Sudiro, T.; Ginting, M.

2017-07-01

ZnO and MnO2 powder were synthesized using solid state reaction method to produce Zn1-xMnxO materials. Effect of dopant concentrations at the material of Zn1-xMnxO (x = 0.015, 0.02, 0.025) to the change of crystal structure, electrical and magnetic properties was studied. The X-ray diffraction (XRD) result of the samples that were doped with Mn showed a hexagonal wurtzite polycrystalline structure. The addition of Mn dopant resulting the decrease of lattice parameters and peaks intensity. The significant increase of the peak intensity occurred at x = 0.02, which also indicated an increase in the crystal quality of ZnO. The change of the ZnO structure affected the electrical and magnetic properties of the samples.

Attachment behaviour of Escherichia coli K12 and Salmonella Typhimurium P6 on food contact surfaces for food transportation.

PubMed

Abban, Stephen; Jakobsen, Mogens; Jespersen, Lene

2012-09-01

The role of cargo container lining materials aluminium, a fibre reinforced plastic (FRP) and stainless steel in bacterial cross contamination during transport was assessed. For this, attachment and detachment of Escherichia coli K12 and Salmonella Typhimurium P6 on the three surfaces in the absence or presence of residues were evaluated. Observations were correlated with water contact angles of the materials (hydrophobicity) and roughness profile (R(a)). Attachment of the organisms was negatively correlated to the hydrophobicity of the three materials with r = -0.869 and -0.861 for E. coli K12 and S. Typhimurium P6 respectively. Correlation with roughness average was poor; r = -0.425 and -0.413 respectively for E. coli K12 and S. Typhimurium P6. Presence of residue caused significant reduction (p < 0.05) in the levels of bacteria attached to all materials, but made attached bacteria significantly more difficult to detach by either of two rinsing systems from all three surfaces. Explanation for these observations could be made in part from scanning electron micrographs which showed significantly more bacteria sitting on patches of residue when it was introduced to the surfaces, compared to the bare material sections of the same surfaces. We report these observations for the first time for aluminium and the FRP material and in part for stainless steel. The S. Typhimurium P6 strain also had significantly higher level of attachment than the E. coli K12 strain. Our findings show that food residue and soils affect the extent and amount of bacteria attaching to abiotic surfaces by altering the surface contact properties for the bacteria. Physicochemical properties like hydrophobicity appear to be a better basis for material selection for hygienic design of containers, than the traditional use of R(a). Copyright © 2012 Elsevier Ltd. All rights reserved.

Health, schooling, needs, perspectives and aspirations of HIV infected and affected children in Botswana: a cross-sectional survey.

PubMed

Anabwani, Gabriel; Karugaba, Grace; Gabaitiri, Lesego

2016-07-22

Antiretroviral treatment means many HIV infected children are surviving with a highly stigmatised condition. There is a paucity of data to inform policies for this growing cohort. Hence we carried out a study on the health, schooling, needs, aspirations, perspectives and knowledge of HIV infected and affected children in Botswana. A cross-sectional survey using interviews and focus group discussions among HIV infected children aged 6-18 years versus HIV aged matched HIV uninfected counterparts living in the same households between August 2010 and March 2011. Supplemental clinical data was abstracted from medical records for HIV infected participants. Nine hundred eighty-four HIV infected and 258 affected children completed the survey. Females predominated in the affected group (63.6 % versus 50.3 %, P < 0.001). School attendance was high in both groups (98.9 % versus 97.3 %, P = 0.057). HIV infected children were mostly in primary school (grades 3-7) while affected children were mostly in upper primary or secondary grades. Sixty percent HIV infected children reported having missed school at least 1 day in the preceding month. Significantly more infected than affected children reported experiencing problems at school (78 % versus 62.3 %, P < 0.001). Twenty-two percent of 15-18 year old HIV infected children were in standard seven and below compared to only 8 % of HIV affected children (p = 0.335). School related problems included poor grades, poor health/school attendance, stigma and inadequate scholastic materials. The wish-list for improving the school environment was similar for both groups and included extra learning support; better meals; protection from bullying/teasing; more scholastic materials, extracurricular activities, love and care; structural improvements; improved teacher attendance and teaching approaches. Significantly more HIV infected children reported feeling hungry all the time (50.6 % versus 41 %, P = 0.007) and more trouble hearing (26.8 % versus 12.5 %, P = 0.028). The mean age for HIV disclosure 10 years was high. Sexual activity (9.2 % versus 3 %, P = 0.001) and emotions of anger (71 % versus 55.3 %, P < 0.001) were significantly higher among HIV affected children. Future perspectives were equally positive (93 % versus 96 %, P = 0.080), were predicated on children's school performance, self-belief/determination and/or ARVs and preference for medical or military careers was common. In Botswana almost all school-age HIV infected and affected children are attending school but many face daunting challenges that call for the creation of an empowering, empathetic, supportive, caring, and non-discriminating school environment.

Effects of ionizing radiation on properties of monolayer and multilayer flexible food packaging materials

NASA Astrophysics Data System (ADS)

Riganakos, K. A.; Koller, W. D.; Ehlermann, D. A. E.; Bauer, B.; Kontominas, M. G.

1999-05-01

Volatile compounds produced in flexible food packaging materials (LDPE, EVAc, PET/PE/EVOH/PE) during electron beam irradiation were isolated by purge and trap technique and identified by combined gas chromatography-mass spectrometry (GC/MS), after thermal desorption and concentration. For comparison purposes non-irradiated films were also studied. Film samples were irradiated at low (5 kGy, corresponding to cold pasteurization), intermediate (20 kGy, corresponding to cold sterilization) and high (100 kGy) doses. It was observed that a number of volatile compounds are produced after irradiation in all cases. Furthermore the amounts of all volatile compounds increase with increasing irradiation dose. Both primary (methyl-derivatives etc.) as well as secondary i.e. oxidation products (ketones, aldehydes, alcohols, carboxylic acids etc.) are produced upon irradiation. These products may affect organoleptic properties and thus shelf-life of prepackaged irradiated foods. No significant changes were observed in the structure of polymer matrices as exhibited by IR spectra after irradiation of the materials at doses tested. Likewise, no significant changes were observed in O 2, H 2O and CO 2 permeability values of plastic packaging materials after irradiation.

The spanning set indicates that variability during the stance period of running is affected by footwear.

PubMed

Kurz, Max J; Stergiou, Nicholas

2003-04-01

Sensory information the foot receives appears to be related to kinematic variability. Since footwear material densities affect sensory information, footwear may be an important factor that dictates variability. This study hypothesized that modifications in footwear would result in changes in kinematic variability during the running stance period. Subjects ran on a treadmill for three conditions: hard shoe, soft shoe and barefoot. The spanning sets of the mean ensemble curves of the knee and ankle changes for each condition were used to define variability. Variability was significantly larger in the barefoot condition in comparison with the two footwear conditions for both joints. These results suggest that variability can be affected by peripheral sensory information. The spanning set methodology can be utilized to examine changes in variability.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anthony D. Rollett; Hasso Weiland; Mohammed Alvi

Carnegie Mellon University was teamed with the Alcoa Technical Center with support from the US Dept. of Energy (Office of Industrial Technology) and the Pennsylvania Technology Investment Authority (PTIA) to make processing of aluminum less costly and more energy efficient. Researchers in the Department of Materials Science and Engineering have investigated how annealing processes in the early stages of aluminum processing affect the structure and properties of the material. Annealing at high temperatures consumes significant amounts of time and energy. By making detailed measurements of the crystallography and morphology of internal structural changes they have generated new information that willmore » provide a scientific basis for shortening processing times and consuming less energy during annealing.« less

Fire Safety in the Low-Gravity Spacecraft Environment

NASA Technical Reports Server (NTRS)

Friedman, Robert

1999-01-01

Research in microgravity (low-gravity) combustion promises innovations and improvements in fire prevention and response for human-crew spacecraft. Findings indicate that material flammability and fire spread in microgravity are significantly affected by atmospheric flow rate, oxygen concentration, and diluent composition. This information can lead to modifications and correlations to standard material-assessment tests for prediction of fire resistance in space. Research on smoke-particle changes in microgravity promises future improvements and increased sensitivity of smoke detectors in spacecraft. Research on fire suppression by extinguishing agents and venting can yield new information on effective control of the rare, but serious fire events in spacecraft.

Effect of Grain Misorientation Angle on Twinning Propagation in Ti-15Mo Alloy

NASA Astrophysics Data System (ADS)

Im, Y.-D.; Lee, Y.-K.; Song, K. H.

2018-07-01

This study was carried out to evaluate the effect of grain misorientation angle distribution on the deformation behavior and twinning of Ti-15Mo alloy. Cold rolling exhibited a significant texture with grains oriented along the {111}//normal direction, which correlate with a higher fraction of low-angle boundaries. This material showed a lower yield strength and higher elongation than those of the hot rolled material. The twinning propagation mainly occurred between neighboring grains with a low-angle relation. Consequently, the texture development was correlated with low-angle boundaries and affected by the increase in the twinning density, which increased the strain hardening rate.

Simbol-X Mirror Module Thermal Shields: II-Small Angle X-Ray Scattering Measurements

NASA Astrophysics Data System (ADS)

Barbera, M.; Ayers, T.; Collura, A.; Nasillo, G.; Pareschi, G.; Tagliaferri, G.

2009-05-01

The formation flight configuration of the Simbol-X mission implies that the X-ray mirror module will be open to Space on both ends. In order to reduce the power required to maintain the thermal stability and, therefore, the high angular resolution of the shell optics, a thin foil thermal shield will cover the mirror module. Different options are presently being studied for the foil material of these shields. We report results of an experimental investigation conducted to verify that the scattering of X-rays, by interaction with the thin foil material of the thermal shield, will not significantly affect the performances of the telescope.

Effect of artificial aging on the surface roughness and microhardness of resin-based materials.

PubMed

Santos, M Jacinta M C; Rêgo, Heleine Maria Chagas; Mukhopadhyay, Anuradha; El Najjar, Mai; Santos, Gildo C

2016-01-01

This study sought to verify the effects of aging on the surface roughness (Ra) and microhardness (Knoop hardness number [KHN]) of resin-based restorative materials protected with a surface sealer. Disc specimens of 2 resin-modified glass ionomers (RMGIs) and 1 composite resin (CR) were fabricated in a metal mold. Specimens of each material were divided into 1 group that was covered with surface sealer and 1 group that was not. Both groups of each material were then subdivided according to whether they were stored (aged) in cola or distilled water. Surface roughness and KHN values were obtained from each specimen before and after storage. After aging of the specimens, significantly higher Ra values were observed in the 2 RMGIs when they were not covered with a surface sealer, while the CR was not affected. The KHN values varied by materials and storage conditions (with and without a surface sealer). All the groups with a surface sealer exhibited increased Ra values after aging.

Effects of chemical disinfectant solutions on the stability and accuracy of the dental impression complex.

PubMed

Rios, M P; Morgano, S M; Stein, R S; Rose, L

1996-10-01

Currently available impression materials were not designed for disinfection or sterilization, and it is conceivable that disinfectants may adversely affect impressions. This study evaluated the accuracy and dimensional stability of polyether (Permadyne/Impregum) and polyvinyl siloxane (Express) impression materials retained by their adhesives in two different acrylic resin tray designs (perforated and nonperforated) when the materials were immersed for either 30 or 60 minutes in three high-level disinfectants. Distilled water and no solution served as controls. A stainless steel test analog similar to ADA specification No. 19 was used. A total of 400 impressions were made with all combinations of impression materials, tray designs, disinfectant, and soaking times. Samples were evaluated microscopically before and after immersion and 48 hours after soaking. Results indicated that these two impression materials were dimensionally stable. Because the results emphasized the stability and accuracy of the impression complex under various conditions, dentists can perform disinfection procedures similar to the protocol of this study without concern for clinically significant distortion of the impression.

The effect of shoe soling tread groove width on the coefficient of friction with different sole materials, floors, and contaminants.

PubMed

Li, Kai Way; Chen, Chin Jung

2004-11-01

Tread groove design is very common in footwear. However, coefficient of friction (COF) measurements between the footwear material and floor using a slipmeter were commonly performed using flat footwear pads. Such measurements might underestimate the actual slip resistance of the footwear pad. This research investigates the effects of the tread groove width on the measured COF using four footwear materials, three floors, and four liquid-contamination conditions using a Brungraber Mark II slipmeter. The analysis of variance results indicated that the footwear material, floor, contamination conditions, and groove width were all significant (p < 0.0001) factors affecting the measured COF. The hypothesis that wider tread grooves result in higher COF values was true with some exceptions especially on oil contaminated floors. A regression model, with an R2 of 0.91, was established to describe and predict the relationship between the COF and the tread groove width under footwear material/floor/contamination conditions.

A Study of Time-dependent and Anisotropic Effects on the Deformation Response of Two Flywheel Designs

NASA Technical Reports Server (NTRS)

Saleeb, Atef F.; Arnold, Steven M.; Al-Zoubi, Nasser R.

2003-01-01

The influence of material time dependency and anisotropy in the context of two specific flywheel designs-preload and multi-directional composite (MDC)--is investigated. In particular, we focus on the following aspects: 1) geometric constraints, 2) material constraints, 3) loading type, and 4) the fundamental character of the time-dependent response, i.e., reversible or irreversible. The bulk of the results presented were obtained using a composite (PMC IM7/8552 at 135 C) material system. The material was characterized using a general multimechanism hereditary (viscoelastoplastic) model. As a general conclusion, the results have clearly shown that both the preload and the MDC rotor designs are significantly affected by time-dependent material behavior, which may impact the state of rotor balance and potentially reduce its operating life. In view of the results of the parametric studies and predictions made in the present study, the need for actual experimentation focusing on the time-dependent behavior of full-scale flywheel rotors is self-evident.

Investigation of Springback Associated with Composite Material Component Fabrication (MSFC Center Director's Discretionary Fund Final Report, Project 94-09)

NASA Technical Reports Server (NTRS)

Benzie, M. A.

1998-01-01

The objective of this research project was to examine processing and design parameters in the fabrication of composite components to obtain a better understanding and attempt to minimize springback associated with composite materials. To accomplish this, both processing and design parameters were included in a Taguchi-designed experiment. Composite angled panels were fabricated, by hand layup techniques, and the fabricated panels were inspected for springback effects. This experiment yielded several significant results. The confirmation experiment validated the reproducibility of the factorial effects, error recognized, and experiment as reliable. The material used in the design of tooling needs to be a major consideration when fabricating composite components, as expected. The factors dealing with resin flow, however, raise several potentially serious material and design questions. These questions must be dealt with up front in order to minimize springback: viscosity of the resin, vacuum bagging of the part for cure, and the curing method selected. These factors directly affect design, material selection, and processing methods.

Everyday music listening and affect regulation: The role of MP3 players

PubMed Central

2013-01-01

The use of digital portable music devices such as MP3 players has rapidly increased during the last decade, and the sheer availability of music offered by such players raises questions about their impact on listeners’ mental and physical health and well-being. This article explores MP3 player use as an everyday tactic for affect regulation, here understood as an individual's efforts to maintain or change the intensity or duration of a given affect. The ability to understand and regulate affects has significant health implications, and among the tactics relevant to such regulation, engagement with music has proven to be particularly successful. The material presented in this article is based on a qualitative interview study focused on MP3 player use as a medium for musical self-care. Because MP3 users can listen to whatever they want, whenever they want, and target their music in the interests of managing and regulating moods and emotions, the MP3 player represents a valuable and convenient technology of affect regulation. PMID:23930987

Everyday music listening and affect regulation: the role of MP3 players.

PubMed

Skånland, Marie Strand

2013-08-07

The use of digital portable music devices such as MP3 players has rapidly increased during the last decade, and the sheer availability of music offered by such players raises questions about their impact on listeners' mental and physical health and well-being. This article explores MP3 player use as an everyday tactic for affect regulation, here understood as an individual's efforts to maintain or change the intensity or duration of a given affect. The ability to understand and regulate affects has significant health implications, and among the tactics relevant to such regulation, engagement with music has proven to be particularly successful. The material presented in this article is based on a qualitative interview study focused on MP3 player use as a medium for musical self-care. Because MP3 users can listen to whatever they want, whenever they want, and target their music in the interests of managing and regulating moods and emotions, the MP3 player represents a valuable and convenient technology of affect regulation.

Effect of packing material on methane activation in a dielectric barrier discharge reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jo, Sungkwon; Hoon Lee, Dae; Seok Kang, Woo

2013-12-15

The conversion of methane is measured in a planar-type dielectric barrier discharge reactor using γ-Al{sub 2}O{sub 3} (sphere), α-Al{sub 2}O{sub 3} (sphere), and γ-Al{sub 2}O{sub 3} (16–20 mesh). Investigations on the surface properties and shape of the three packing materials clearly indicate that methane activation is considerably affected by the material used. Capacitances inside the discharge gap are estimated from charge–voltage plots, and a comparison of the generated and transferred charges for different packing conditions show that the difference in surface properties between γ- and α-phase Al{sub 2}O{sub 3} affects the discharge characteristics. Moreover, all packing conditions show different chargemore » characteristics that are related to the electron density. Finally, the packing material's shape affects the local electron temperature, which is strongly related to methane conversion. The combined results indicate that both microscale and macroscale variations in a packing material affect the discharge characteristics, and a packing material should be considered carefully for effective methane activation.« less

Genetics Home Reference: Jacobsen syndrome

MedlinePlus

... varies among affected individuals, with most affected people missing 5 million to 16 million DNA building blocks ( ... translocation can have a chromosomal rearrangement with some missing genetic material and some extra genetic material. Individuals ...

Selected applications for current polymers in prosthetic dentistry - state of the art.

PubMed

Kawala, Maciej; Smardz, Joanna; Adamczyk, Lukasz; Grychowska, Natalia; Wieckiewicz, Mieszko

2018-05-10

Polymers are widely applied in medicine, including dentistry, i.e. in prosthodontics. The following paper is aimed at demonstrating the applications of selected modern polymers in prosthetic dentistry based on the reported literature. The study was conducted using the PubMed, SCOPUS and CINAHL databases in relation to documents published during 1999-2017. The following keywords were used: polymers with: prosthetic dentistry, impression materials, denture base materials, bite registration materials, denture soft liners, occlusal splint materials and 3D printing. Original papers and reviews which were significant from the modern clinical viewpoint and practical validity in relation to the possibility of using polymeric materials in prosthetic dentistry, were presented. Denture base materials were most commonly modified polymers. Modifications mainly concerned antimicrobial properties and reinforcement of the material structure by introducing additional fibers. Antimicrobial modifications were also common in case of relining materials. Polymeric materials have widely been used in prosthetic dentistry. Modifications of their composition allow achieving new, beneficial properties that affect quality of patients' life. Progress in science allows for a more methodologically-advanced research on the synthesis of new polymeric materials and incorporation of new substances into already known polymeric materials, that will require systematization and appropriate classification. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Toxicity and environmental and economic performance of fly ash and recycled concrete aggregates use in concrete: A review.

PubMed

Kurda, Rawaz; Silvestre, José D; de Brito, Jorge

2018-04-01

This paper presents an overview of previous studies on the environmental impact (EI) and toxicity of producing recycled concrete aggregates (RCA), fly ash (FA), cement, superplasticizer, and water as raw materials, and also on the effect of replacing cement and natural aggregates (NA) with FA and RCA, respectively, on the mentioned aspects. EI and toxicity were analysed simultaneously because considering concrete with alternative materials as sustainable depends on whether their risk assessment is high. Therefore, this study mainly focuses on the cradle-to-gate EI of one cubic meter of concrete, namely abiotic depletion potential (ADP), global warming potential (GWP), ozone depletion potential (ODP), photochemical ozone creation (POCP), acidification potential (AP), eutrophication potential (EP), non-renewable energy (PE-NRe) and renewable energy (PE-Re). In terms of toxicity, leachability (chemical and ecotoxicological characterization) was considered. The results also include the economic performance of these materials, and show that the incorporation of FA in concrete significantly decreases the EI and cost of concrete. Thus, the simultaneous incorporation of FA and RCA decrease the EI, cost, use of landfill space and natural resources extraction. Nonetheless, the leaching metals of FA decrease when they are incorporated in concrete. Relative to FA, the incorporation of RCA does not significantly affect the EI and cost of concrete, but it significantly reduces the use of landfill space and the need of virgin materials.

Neuropsychologic assessment of long-term survivors of childhood leukemia.

PubMed

Pfefferbaum-Levine, B; Copeland, D R; Fletcher, J M; Ried, H L; Jaffe, N; McKinnon, W R

1984-01-01

Thirty-two long-term survivors of childhood leukemia who were followed up at the University of Texas M. D. Anderson Hospital were evaluated with a battery of 17 neuropsychologic tests. These tests were selected to assess the development of cognitive skills and functions associated with brain impairment in children. Statistically significant differences were found between the group of children given CNS irradiation and the nonirradiated group on full-scale IQ and verbal IQ scores, mathematics skills, constructional skills, and memory for spatial material. Of particular interest was the absence of differences in language-based measures of verbal memory and the presence of group differences on measures of memory for spatial material. While the sample size was small, the findings delineate specific areas likely to be affected. These results indicate the need for caution when including cranial irradiation in CNS prophylaxis. When any CNS treatment is given, it seems appropriate that provisions be made for assessment and remediation of affected skills.

Uniaxial low cycle fatigue behavior for pre-corroded 16MND5 bainitic steel in simulated pressurized water reactor environment

NASA Astrophysics Data System (ADS)

Chen, Xu; Ren, Bin; Yu, Dunji; Xu, Bin; Zhang, Zhe; Chen, Gang

2018-06-01

The effects of uniaxial tension properties and low cycle fatigue behavior of 16MND5 bainitic steel cylinder pre-corroded in simulated pressurized water reactor (PWR) were investigated by fatigue at room temperature in air and immersion test system, scanning electron microscopy (SEM), energy disperse spectroscopy (EDS). The experimental results indicated that the corrosion fatigue lives of 16MND5 specimen were significantly affected by the strain amplitude and simulated PWR environments. The compositions of corrosion products were complexly formed in simulated PWR environments. The porous corrosion surface of pre-corroded materials tended to generate pits as a result of promoting contact area to the fresh metal, which promoted crack initiation. For original materials, the fatigue cracks initiated at inclusions imbedded in the micro-cracks. Moreover, the simulated PWR environments degraded the mechanical properties and low cycle fatigue behavior of 16MND5 specimens remarkably. Pre-corrosion of 16MND5 specimen mainly affected the plastic term of the Coffin-Manson equation.

The influence of storage duration on the setting time of type 1 alginate impression material

NASA Astrophysics Data System (ADS)

Rahmadina, A.; Triaminingsih, S.; Irawan, B.

2017-08-01

Alginate is one of the most commonly used dental impression materials; however, its setting time is subject to change depending on storage conditions and duration. This creates problems because consumer carelessness can affect alginate shelf life and quality. In the present study, the setting times of two groups of type I alginate with different expiry dates was tested. The first group consisted of 11 alginate specimens that had not yet passed the expiry date, and the second group consisted of alginates that had passed the expiry date. The alginate powder was mixed with distilled water, poured into a metal ring, and tested with a polished rod of poly-methyl methacrylate. Statistical analysis showed a significant difference (p<0.05) between the setting times of the alginate that had not passed the expiry date (157 ± 3 seconds) and alginate that had passed the expiry date (144 ± 2 seconds). These findings indicate that storage duration can affect alginate setting time.

Effect of welding on creep damage evolution in P91B steel

NASA Astrophysics Data System (ADS)

Baral, J.; Swaminathan, J.; Chakrabarti, D.; Ghosh, R. N.

2017-07-01

Study of creep behavior of base metal (without weld) and welded specimens of P91B steel over a range of temperatures (600-650 °C) and stresses (50-180 MPa) showed similar values of minimum creep-rates for both specimens at higher stress regime (>100 MPa) whilst, significantly higher creep rates in the case of welded specimens at lower stress regime. Considering that welded specimen is comprised of two distinct structural regimes, i.e. weld affected zone and base metal, a method has been proposed for estimating the material parameters describing creep behavior of those regimes. Stress-strain distribution across welded specimen predicted from finite element analysis based on material parameters revealed preferential accumulation of stress and creep strain at the interface between weld zone and base metal. This is in-line with the experimental finding that creep rupture preferentially occurs at inter-critical heat affected zone in welded specimens owing to ferrite-martensite structure with coarse Cr23C6 particles.

Evaluating the complexity of online patient education materials about brain aneurysms published by major academic institutions.

PubMed

Gupta, Raghav; Adeeb, Nimer; Griessenauer, Christoph J; Moore, Justin M; Patel, Apar S; Kim, Christopher; Thomas, Ajith J; Ogilvy, Christopher S

2017-08-01

OBJECTIVE Health care education resources are increasingly available on the Internet. A majority of people reference these resources at one point or another. A threshold literacy level is needed to comprehend the information presented within these materials. A key component of health literacy is the readability of educational resources. The National Institutes of Health (NIH) and the American Medical Association have recommended that patient education materials be written between a 4th- and a 6th-grade education level. The authors assessed the readability of online patient education materials about brain aneurysms that have been published by several academic institutions across the US. METHODS Online patient education materials about brain aneurysms were downloaded from the websites of 20 academic institutions. The materials were assessed via 8 readability scales using Readability Studio software (Oleander Software Solutions), and then were statistically analyzed. RESULTS None of the patient education materials were written at or below the NIH's recommended 6th-grade reading level. The average educational level required to comprehend the texts across all institutions, as assessed by 7 of the readability scales, was 12.4 ± 2.5 (mean ± SD). The Flesch Reading Ease Scale classified the materials as "difficult" to understand, correlating with a college-level education or higher. An ANOVA test found that there were no significant differences in readability among the materials from the institutions (p = 0.215). CONCLUSIONS Brain aneurysms affect 3.2% of adults 50 years or older across the world and can cause significant patient anxiety and uncertainty. Current patient education materials are not written at or below the NIH's recommended 4th- to 6th-grade education level.

Propagation of Valuable North Sumatera Benzoin Trees (Styrax Sp) Using Macrocutting Technique

NASA Astrophysics Data System (ADS)

Susilowati, A.; Hartini, K. S.; Rachmat, H. H.; Alvaroby, M.

2017-03-01

Kemenyan known as Sumatran benzoin is North Sumatera local species that produce high valuable rosin and prospective export comodities. However, sustainability of Sumatran benzoin production has many constraints such as instability of resin production, lack information of propagation technique and traditional management system. Until now, comprehensive information for Sumatran benzoin propagation system still not determined yet. The objectives of this research were (1) to get information about propagation technique of Sumatran benzoin and its suitable growing medium and 2) to get information on adventitious root formation in Sumatran benzoin cuttings. Cutting materials (Toba benzoin and Durame benzoin) were originated from 1 year old seedling propagated by seed. Media used were combination of sand : rice husk (1:0 v/v; 1/1 v/v). Results showed that interaction between media and benzoin species significantly affected primer and secondary root lenght. While planting medium significantly improved secondary root length and number. Benzoin species significantly affected primary and secondary root lenght, and secondary root number.

Materials for interocclusal records and their ability to reproduce a 3-dimensional jaw relationship.

PubMed

Ockert-Eriksson, G; Eriksson, A; Lockowandt, P; Eriksson, O

2000-01-01

The purpose of this study was to determine if accuracy and dimensional stability of vinyl polysiloxanes and irreversible hydrocolloids stabilized by a tray used for fixed prosthodontics, removable partial, and complete denture cases are comparable to those of waxes and record rims and if storage time (24 hours or 6 days) affects dimensional stability of the tested materials. Two waxes, two record rims, three vinyl polysiloxanes, and one irreversible hydrocolloid (alginate) were examined. Three pairs of master casts with measuring steel rods were mounted on an articulator (initial position). Five records were made of each material, and the upper cast was remounted after 24 hours or 6 days so that deviations from the initial position could be measured. Vinyl polysiloxanes reinforced by a stabilization tray were the most accurate materials able to reproduce a settled interocclusal position. Mounting casts (fixed prosthodontics cases) without records gave accuracy similar to wax records. Record rims used for removable partial and complete denture cases produced lesser accuracy than vinyl polysiloxanes and irreversible hydrocolloid stabilized by a tray. Accuracy was not significantly affected by storage time. The results show that accuracy of vinyl polysiloxanes and irreversible hydrocolloids reinforced by a tray is superior to that of record rims with regard to the complete denture case and is among the most accurate with regard to the removable partial denture case. For fixed prosthodontics, however, reinforcement is unnecessary.

Sorption and Diffusion of Water Vapor and Carbon Dioxide in Sulfonated Polyaniline as Chemical Sensing Materials.

PubMed

Liang, Qiuhua; Jiang, Junke; Ye, Huaiyu; Yang, Ning; Cai, Miao; Xiao, Jing; Chen, Xianping

2016-04-27

A hybrid quantum mechanics (QM)/molecular dynamics (MD) simulation is performed to investigate the effect of an ionizable group (-SO₃(-)Na⁺) on polyaniline as gas sensing materials. Polymers considered for this work include emeraldine base of polyaniline (EB-PANI) and its derivatives (Na-SPANI (I), (II) and (III)) whose rings are partly monosubstituted by -SO₃(-)Na⁺. The hybrid simulation results show that the adsorption energy, Mulliken charge and band gap of analytes (CO₂ and H₂O) in polyaniline are relatively sensitive to the position and the amounts of -SO₃(-)Na⁺, and these parameters would affect the sensitivity of Na-SPANI/EB-PANI towards CO₂. The sensitivity of Na-SPANI (III)/EB-PANI towards CO₂ can be greatly improved by two orders of magnitude, which is in agreement with the experimental study. In addition, we also demonstrate that introducing -SO₃(-)Na⁺ groups at the rings can notably affect the gas transport properties of polyaniline. Comparative studies indicate that the effect of ionizable group on polyaniline as gas sensing materials for the polar gas molecule (H₂O) is more significant than that for the nonpolar gas molecule (CO₂). These findings contribute in the functionalization-induced variations of the material properties of polyaniline for CO₂ sensing and the design of new polyaniline with desired sensing properties.

Comparison of the basin-scale effect of dredging operations and natural estuarine processes on suspended sediment concentration

USGS Publications Warehouse

Schoellhamer, D.H.

2002-01-01

Suspended sediment concentration (SSC) data from San Pablo Bay, California, were analyzed to compare the basin-scale effect of dredging and disposal of dredged material (dredging operations) and natural estuarine processes. The analysis used twelve 3-wk to 5-wk periods of mid-depth and near-bottom SSC data collected at Point San Pablo every 15 min from 1993-1998. Point San Pablo is within a tidal excursion of a dredged-material disposal site. The SSC data were compared to dredging volume, Julian day, and hydrodynamic and meteorological variables that could affect SSC. Kendall's ??, Spearman's ??, and weighted (by the fraction of valid data in each period) Spearman's ??w correlation coefficients of the variables indicated which variables were significantly correlated with SSC. Wind-wave resuspension had the greatest effect on SSC. Median water-surface elevation was the primary factor affecting mid-depth SSC. Greater depths inhibit wind-wave resuspension of bottom sediment and indicate greater influence of less turbid water from down estuary. Seasonal variability in the supply of erodible sediment is the primary factor affecting near-bottom SSC. Natural physical processes in San Pablo Bay are more areally extensive, of equal or longer duration, and as frequent as dredging operations (when occurring), and they affect SSC at the tidal time scale. Natural processes control SSC at Point San Pablo even when dredging operations are occurring.

EFFECT OF CONVENTIONAL AND EXPERIMENTAL GINGIVAL RETRACTION SOLUTIONS ON THE TENSILE STRENGTH AND INHIBITION OF POLYMERIZATION OF FOUR TYPES OF IMPRESSION MATERIALS

PubMed Central

Sábio, Sérgio; Franciscone, Paulo Afonso; Mondelli, José

2008-01-01

In the present study, two types of tests (tensile strength test and polymerization inhibition test) were performed to evaluate the physical and chemical properties of four impression materials [a polysulfide (Permlastic), a polyether (Impregum), a condensation silicone (Xantopren) and a polyvinylsiloxane (Aquasil)] when polymerized in contact with of one conventional (Hemostop) and two experimental (Vislin and Afrin) gingival retraction solutions. For the tensile strength test, the impression materials were mixed and packed into a steel plate with perforations that had residues of the gingival retraction solutions. After polymerization, the specimens were tested in tensile strength in a universal testing machine. For the polymerization inhibition test, specimens were obtained after taking impressions from a matrix with perforations that contained 1 drop of the gingival retraction solutions. Two independent examiners decided on whether or not impression material remnants remained unpolymerized, indicating interference of the chemical solutions. Based on the analysis of the results of both tests, the following conclusions were reached: 1. The tensile strength of the polysulfide decreased after contact with Hemostop and Afrin. 2. None of the chemical solutions inhibited the polymerization of the polysulfide; 3. The polyether presented lower tensile strength after polymerization in contact with the three gingival retraction agents; 4. The polyether had its polymerization inhibited only by Hemostop; 5. None of the chemical solutions affected the tensile strength of the condensation silicone; 6. Only Hemostop inhibited the polymerization of the condensation silicone; 7. The polyvinylsiloxane specimens polymerized in contact with Hemostop had significantly lower tensile strength; 8. Neither of the chemical solutions (Afrin and Vislin) affected the tensile strength of the polyvinylsiloxane and the condensation silicone; 9. Results of the tensile strength and polymerization inhibition tests suggest that Vislin can be used as substance of gingival retraction without affecting the tested properties of four impression materials. PMID:19089261

Potential of pelleted wheat straw as an alternative bedding material for broilers.

PubMed

Kheravii, S K; Swick, R A; Choct, M; Wu, S-B

2017-06-01

Broiler chickens are commonly placed on wood shavings as litter, but alternative litter sources are required due to the scarcity of wood shavings in many parts of the world. This study aimed to compare pelleted straw, chopped wheat straw, wood shavings, rice hulls, and shredded paper as litter candidates. Three-hundred-sixty Ross 308 one-day-old male chicks were used in this study. There were 5 litter treatments with 6 replicate pens, each with 12 birds. The feed conversion ratio (FCR) of birds reared on pelleted straw was improved compared (P < 0.05) to that of birds raised on rice hulls, whereas it did not differ for birds placed on wood shavings, rice hulls, chopped straw, or shredded paper. It was observed that the birds reared on wood shavings had higher relative gizzard weight at d 24 compared to those reared on pelleted straw (P < 0.05). Gizzard pH and measured cecal bacterial groups were not affected by the type of bedding material. Cecal bacterial groups measured at d 10 were not affected by bedding material. Birds reared on pelleted wheat straw had a lower incidence of footpad lesions than those on chopped straw and shredded paper on d 24 (P < 0.001) and 29 (P < 0.01). Litter source did not affect the occurrence of breast blisters at d 24, 29, or 35. On d 24, 29, and 35, pelleted straw litter was less caked than chopped straw and shredded paper (P < 0.001) whereas no significant differences were observed among pelleted straw, wood shavings, and rice hulls. The study demonstrated the potential benefits to using pelleted wheat straw as a bedding material. Further assessment of pelleting of wheat straw and other materials on broiler health, performance, and welfare are needed to determine the economic benefits of pelleted litter. © 2017 Poultry Science Association Inc.

Effect of conventional and experimental gingival retraction solutions on the tensile strength and inhibition of polymerization of four types of impression materials.

PubMed

Sábio, Sérgio; Franciscone, Paulo Afonso; Mondelli, José

2008-01-01

In the present study, two types of tests (tensile strength test and polymerization inhibition test) were performed to evaluate the physical and chemical properties of four impression materials [a polysulfide (Permlastic), a polyether (Impregum), a condensation silicone (Xantopren) and a polyvinylsiloxane (Aquasil)] when polymerized in contact with of one conventional (Hemostop) and two experimental (Vislin and Afrin) gingival retraction solutions. For the tensile strength test, the impression materials were mixed and packed into a steel plate with perforations that had residues of the gingival retraction solutions. After polymerization, the specimens were tested in tensile strength in a universal testing machine. For the polymerization inhibition test, specimens were obtained after taking impressions from a matrix with perforations that contained 1 drop of the gingival retraction solutions. Two independent examiners decided on whether or not impression material remnants remained unpolymerized, indicating interference of the chemical solutions. Based on the analysis of the results of both tests, the following conclusions were reached: 1. The tensile strength of the polysulfide decreased after contact with Hemostop and Afrin. 2. None of the chemical solutions inhibited the polymerization of the polysulfide; 3. The polyether presented lower tensile strength after polymerization in contact with the three gingival retraction agents; 4. The polyether had its polymerization inhibited only by Hemostop; 5. None of the chemical solutions affected the tensile strength of the condensation silicone; 6. Only Hemostop inhibited the polymerization of the condensation silicone; 7. The polyvinylsiloxane specimens polymerized in contact with Hemostop had significantly lower tensile strength; 8. Neither of the chemical solutions (Afrin and Vislin) affected the tensile strength of the polyvinylsiloxane and the condensation silicone; 9. Results of the tensile strength and polymerization inhibition tests suggest that Vislin can be used as substance of gingival retraction without affecting the tested properties of four impression materials.

Thermal characterization and model free kinetics of aged epoxies and foams using TGA and DSC methods.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cordaro, Joseph Gabriel; Kruizenga, Alan Michael; Nissen, April

2013-10-01

Two classes of materials, poly(methylene diphenyl diisocyanate) or PMDI foam, and cross-linked epoxy resins, were characterized using thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC), to help understand the effects of aging and %E2%80%9Cbake-out%E2%80%9D. The materials were evaluated for mass loss and the onset of decomposition. In some experiments, volatile materials released during heating were analyzed via mass spectroscopy. In all, over twenty materials were evaluated to compare the mass loss and onset temperature for decomposition. Model free kinetic (MFK) measurements, acquired using variable heating rate TGA experiments, were used to calculate the apparent activation energy of thermal decomposition.more » From these compiled data the effects of aging, bake-out, and sample history on the thermal stability of materials were compared. No significant differences between aged and unaged materials were detected. Bake-out did slightly affect the onset temperature of decomposition but only at the highest bake-out temperatures. Finally, some recommendations for future handling are made.« less

Department of Defense Agency Financial Report for Fiscal Year 2012. Financial Section

DTIC Science & Technology

2012-01-01

medical malpractice ; property or environmental damages; and contract disputes. Other liabilities also arise as a result of anticipated disposal costs...material misstatement of the entity’s financial statements will not be prevented , or detected and corrected on a timely basis. 3 A control deficiency...to prevent or detect misstatements on a timely basis. A significant deficiency is a deficiency, or a combination of deficiencies, adversely affecting

Planetary Surface-Atmosphere Interactions

NASA Astrophysics Data System (ADS)

Merrison, J. P.; Bak, E.; Finster, K.; Gunnlaugsson, H. P.; Holstein-Rathlou, C.; Knak Jensen, S.; Nørnberg, P.

2013-09-01

Planetary bodies having an accessible solid surface and significant atmosphere, such as Earth, Mars, Venus, Titan, share common phenomenology. Specifically wind induced transport of surface materials, subsequent erosion, the generation and transport of solid aerosols which leads both to chemical and electrostatic interaction with the atmosphere. How these processes affect the evolution of the atmosphere and surface will be discussed in the context of general planetology and the latest laboratory studies will be presented.

Avalanche Photoconductive Switching

DTIC Science & Technology

1989-06-01

implantation and by MBE growth , and p-type material was created by MBE growth of a Be doped layer. Ion implantation creates a heavily doped layer...which is used commonly for GaAs integrated circuits. We plan to use Ti-Pt-Au for p-type contacts in the future. Experimental Results Test Confi...optical wavelenght does not significantly affect the switching process. Another feature of this mode of operation is that there is a threshold

Perception of the material properties of wood based on vision, audition, and touch.

PubMed

Fujisaki, Waka; Tokita, Midori; Kariya, Kenji

2015-04-01

Most research on the multimodal perception of material properties has investigated the perception of material properties of two modalities such as vision-touch, vision-audition, audition-touch, and vision-action. Here, we investigated whether the same affective classifications of materials can be found in three different modalities of vision, audition, and touch, using wood as the target object. Fifty participants took part in an experiment involving the three modalities of vision, audition, and touch, in isolation. Twenty-two different wood types including genuine, processed, and fake were perceptually evaluated using a questionnaire consisting of twenty-three items (12 perceptual and 11 affective). The results demonstrated that evaluations of the affective properties of wood were similar in all three modalities. The elements of "expensiveness, sturdiness, rareness, interestingness, and sophisticatedness" and "pleasantness, relaxed feelings, and liked-disliked" were separately grouped for all three senses. Our results suggest that the affective material properties of wood are at least partly represented in a supramodal fashion. Our results also suggest an association between perceptual and affective properties, which will be a useful tool not only in science, but also in applied fields. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Short communication: Dairy bedding type affects survival of Prototheca in vitro.

PubMed

Adhikari, N; Bonaiuto, H E; Lichtenwalner, A B

2013-01-01

Protothecae are algal pathogens, capable of causing bovine mastitis, that are unresponsive to treatment; they are believed to have an environmental reservoir. The role of bedding management in control of protothecal mastitis has not been studied. The purpose of this study was to evaluate the growth of either environmental or mastitis-associated Prototheca genotypes in dairy bedding materials that are commonly used in Maine. Prototheca zopfii genotypes 1 and 2 (gt1 and gt2) were inoculated into sterile broth only (control ), kiln-dried spruce shavings, "green" hemlock sawdust, sand, or processed manure-pack beddings with broth, and incubated for 2 d. Fifty microliters of each isolate was then cultured onto plates and the resulting colonies counted at 24 and 48 h postinoculation. Shavings were associated with significantly less total Prototheca growth than other bedding types. Growth of P. zopfii gt1 was significantly higher than that of gt2 in the manure-pack bedding material. Spruce shavings, compared with manure, sand, or sawdust, may be a good bedding type to prevent growth of Prototheca. Based on these in vitro findings, bedding type may affect Prototheca infection of cattle in vivo. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The Role of Self-regulation and Affective Control in Predicting Interpersonal Reactivity of Drug Addicts

PubMed Central

Abolghasemi, Abbas; Rajabi, Saeed

2013-01-01

Background Due to its progressive nature in all aspects of life, addiction endangers the health of individuals, families and the society. Objectives The purpose of this study was to determine the role of self-regulation and affective control in predicting interpersonal reactivity of drug addicts. Materials and Methods This research is a correlation study. The statistical population of this study includes all drug addicts who were referred to addiction treatment centers of Ardabil in 2011 of whom 160 addicts were selected through convenience sampling. A self-regulation questionnaire, interpersonal reactivity questionnaire and affective control scale were used for data collection. Results Research results showed that self-regulation (r = -0.40) and affective control (r = -0.29) have a significant relationship with interpersonal reactivity of addicts (P < 0.001). The results of the multiple regression analysis indicated that 19 percent of interpersonal reactivity can be predicted by self-regulation and affective control. Conclusion These results suggest that self-regulation and affective control play an important role in exacerbating as well as reducing interpersonal reactivity of addicts. PMID:24971268

The Comparison of Self-regulation and Affective Control in Methamphetamine and Narcotics Addicts and Non-Addicts

PubMed Central

Tayyebi, Kolthoum; Abolghasemi, Abbas; Mahmood Alilu, Majid; Monirpoor, Nader

2013-01-01

Background Increased prevalence and widespread use of methamphetamine is the public challenge and worry in the world. It seems that low levels of self-regulation and affective control to carry up probability of psychoactive drugs abuse. Objectives The purpose of the present study is the comparison of self-regulation and affective control in methamphetamine and narcotics addicts and non-addicts. Materials and Methods In this causative-comparative study, 80 addicts (40 methamphetamine addicts and 40 narcotic addicts) who referred to self-reference quitting addictive centers in Miyaneh, Iran, participated in convenience sampling. Then, they matched up with 40 non-addicts according to age, sex, educational level, and marital status. To collect data, we used self-regulation questionnaire and affective control scale. The data was analyzed by multivariate analysis of variance (MANOVA) and LSD test. Results Result shows that there is a significant difference between methamphetamine addicts and narcotics addicts and non-addicts in self-regulation and affective control (P = 0.001). Conclusions This finding indicates that low self-regulation and affective control is a risky factor in psychoactive drugs abuse. PMID:24971258

Competitive light absorbers in photoactive dental resin-based materials.

PubMed

Hadis, Mohammed A; Shortall, Adrian C; Palin, William M

2012-08-01

The absorbance profile of photoinitiators prior to, during and following polymerization of light curable resin-based materials will have a significant effect on the cure and color properties of the final material. So-called "colorless" photoinitiators are used in some light-activated resin-based composite restorative materials to lessen the yellowing effect of camphoroquinone (CQ) in order to improve the esthetic quality of dental restorations. This work characterizes absorption properties of commonly used photoinitiators, an acylphosphine oxide (TPO) and CQ, and assesses their influence on material discoloration. Dimethacrylate resin formulations contained low (0.0134 mol/dm(3)), intermediate (0.0405 mol/dm(3)) or high (0.0678 mol/dm(3)) concentrations of the photoinitiators and the inhibitor, butylated hydroxytoluene (BHT) at 0, 0.1 or 0.2% by mass. Disc shaped specimens (n = 3) of each resin were polymerized for 60s using a halogen light curing unit. Dynamic measurements of photoinitiator absorption, polymer conversion and reaction temperature were performed. A spectrophotometer was used to measure the color change before and after cure. GLM three-way analysis of variance revealed significant differences (p<0.001), where photoinitiator concentration (df = 2; F = 618.83)>photoinitiator type (df = 1; F = 176.12)>% BHT (df = 2, F = 13.17). BHT concentration affected the rate of polymerization and produced lower conversion in some of the CQ-based resins. Significant differences between photoinitiator type and concentrations were seen in color (where TPO resins became yellower and camphoroquinone resins became less yellow upon irradiation). Reaction temperature, kinetics and conversion also differed significantly for both initiators (p<0.001). Despite TPO-based resins producing a visually perceptible color change upon polymerization, the color change was significantly less than that produced with CQ-based resins. Although some photoinitiators such as TPO may be a more esthetic alternative to CQ, they may actually cause significant color contamination when used in high concentrations and therefore manufacturers should limit its concentration in order to improve its esthetic quality. Copyright © 2012 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hooper, R. J.; Adams, D. P.; Hirschfeld, D.

The rapid release of energy from reactive multilayer foils can create extreme local temperature gradients near substrate materials. To fully exploit the potential of these materials, a better understanding of the interaction between the substrate or filler material and the foil is needed. In particular, this work investigates how variations in local properties within the substrate (i.e. differences between properties in constituent phases) can affect heat transport into the substrate. Furthermore, this can affect the microstructural evolution observed within the substrate, which may affect the final joint properties. The effect of the initial substrate microstructure on microstructural evolution within themore » heat-affected zone is evaluated experimentally in two Sn-Zn alloys and numerical techniques are utilized to inform the analysis.« less

The phase state of NiTi implant material affects osteoclastic attachment.

PubMed

Muhonen, V; Heikkinen, R; Danilov, A; Jämsä, T; Ilvesaro, J; Tuukkanen, J

2005-12-01

In the present work, the responses of mature osteoclasts cultured on austenite and martensite phases of NiTi shape memory implant material were studied. We used the sensitivity of osteoclasts to the underlying substrate and actin ring formation as an indicator of the adequacy of the implant surface. The results showed osteoclasts with actin ring on both NiTi phases. However, significantly more osteoclasts were present on the austenitic NiTi than on the martensitic NiTi. We also analyzed the surface free energy of the samples but found no significant difference between austenite and martensite phases. The results revealed that osteoclasts tolerated well the austenite phase of NiTi. The chemically identical martensitic NiTi was not as well tolerated by osteoclasts (e.g., indicated by diminished actin ring formation). This leads to the conclusion that certain physical properties specific to the martensitic NiTi have an adverse effect to the surviving of osteoclasts on this NiTi phase. These results confirm that mature, authentic osteoclasts can act as cell probes in experiments concerning aspects of biocompatibility of bone implant materials. (c) 2005 Wiley Periodicals, Inc.

Molecular plasmonics: The role of rovibrational molecular states in exciton-plasmon materials under strong-coupling conditions

NASA Astrophysics Data System (ADS)

Sukharev, Maxim; Charron, Eric

2017-03-01

We extend the model of exciton-plasmon materials to include a rovibrational structure of molecules using wave-packet propagations on electronic potential energy surfaces. Our model replaces conventional two-level emitters with more complex molecules, allowing us to examine the influence of alignment and vibrational dynamics on strong coupling with surface plasmon-polaritons. We apply the model to a hybrid system comprising a thin layer of molecules placed on top of a periodic array of slits. Rigorous simulations are performed for two types of molecular systems described by vibrational bound-bound and bound-continuum electronic transitions. Calculations reveal new features in transmission, reflection, and absorption spectra, including the observation of significantly higher values of the Rabi splitting and vibrational patterns clearly seen in the corresponding spectra. We also examine the influence of anisotropic initial conditions on optical properties of hybrid materials, demonstrating that the optical response of the system is significantly affected by an initial prealignment of the molecules. Our work demonstrates that prealigned molecules could serve as an efficient probe for the subdiffraction characterization of the near-field near metal interfaces.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neuscamman, Stephanie J.

This section describes ways in which an urban environment can affect the distribution of airborne radiological material. In an urban area, winds at street level are significantly more variable and complex than the prevailing winds above the buildings. Elevated winds may be uniform and representative of the general flow over the surrounding area, but buildings influence the local flow such that the winds below the building heights vary significantly in location and time (Hanna et al 2006). For a release of material near an individual building, the complex effect of the building on the airflow may locally enhance the airmore » concentration of released material in some regions near the building and reduce it in others compared to a release in open terrain. However, the overall effect of an individual building is to induce a rapid enlargement and dilution of an incident plume from an isolated source upwind of the building (Hosker 1984). A plume spreading through an urban environment of multiple buildings will experience enhanced mixing and greater spreading of the contaminant plume in both the vertical and horizontal directions, compared to the same release in open terrain.« less

Food structure: Its formation and relationships with other properties.

PubMed

Joardder, Mohammad U H; Kumar, Chandan; Karim, M A

2017-04-13

Food materials are complex in nature as it has heterogeneous, amorphous, hygroscopic and porous properties. During processing, microstructure of food materials changes which significantly affects other properties of food. An appropriate understanding of the microstructure of the raw food material and its evolution during processing is critical in order to understand and accurately describe dehydration processes and quality anticipation. This review critically assesses the factors that influence the modification of microstructure in the course of drying of fruits and vegetables. The effect of simultaneous heat and mass transfer on microstructure in various drying methods is investigated. Effects of changes in microstructure on other functional properties of dried foods are discussed. After an extensive review of the literature, it is found that development of food structure significantly depends on fresh food properties and process parameters. Also, modification of microstructure influences the other properties of final product. An enhanced understanding of the relationships between food microstructure, drying process parameters and final product quality will facilitate the energy efficient optimum design of the food processor in order to achieve high-quality food.

Poverty and transitions in health in later life.

PubMed

Adena, Maja; Myck, Michal

2014-09-01

Using a sample of Europeans aged 50+ from 12 countries in the Survey of Health, Ageing and Retirement in Europe (SHARE), we analyse the role of poor material conditions as a determinant of changes in health over a four- to five-year period. We find that poverty defined with respect to relative income has no effect on changes in health. However, broader measures of poor material conditions, such as subjective poverty or low wealth, significantly increase the probability of transition to poor health among the healthy and reduce the chance of recovery from poor health over the time interval analysed. In addition to this, the subjective measure of poverty has a significant effect on mortality, increasing it by 65% among men and by 68% among those aged 50-64. Material conditions affect health among older people. We suggest that if attempts to reduce poverty in later life and corresponding policy targets are to focus on the relevant measures, they should take into account broader definitions of poverty than those based only on relative incomes. Copyright © 2014 Elsevier Ltd. All rights reserved.

The effects of non-contingent extrinsic and intrinsic rewards on memory consolidation.

PubMed

Nielson, Kristy A; Bryant, Ted

2005-07-01

Emotional and arousing treatments given shortly after learning enhance delayed memory retrieval in animal and human studies. Positive affect and reward induced prior to a variety of cognitive tasks enhance performance, but their ability to affect memory consolidation has not been investigated before. Therefore, we investigated the effects of a small, non-contingent, intrinsic or extrinsic reward on delayed memory retrieval. Participants (n=108) studied and recalled a list of 30 affectively neutral, imageable nouns. Experimental groups were then given either an intrinsic reward (e.g., praise) or an extrinsic reward (e.g., US 1 dollar). After a one-week delay, participants' retrieval performance for the word list was significantly better in the extrinsic reward groups, whether the reward was expected or not, than in controls. Those who received the intrinsic reward performed somewhat better than controls, but the difference was not significant. Thus, at least some forms of arousal and reward, even when semantically unrelated to the learned material, can effectively modulate memory consolidation. These types of treatments might be useful for the development of new memory intervention strategies.

Factors affecting interest in orthopedics among female medical students: a prospective analysis.

PubMed

Baldwin, Keith; Namdari, Surena; Bowers, Andrea; Keenan, Mary Ann; Levin, L Scott; Ahn, Jaimo

2011-12-06

The field of orthopedics has a limited ability to recruit high-quality female applicants. The purpose of this study was to determine whether early exposure to the field affects a woman's decision to pursue orthopedics. We performed a prospective, nonrandomized cohort study between academic years 2005 and 2009 and compared interest in orthopedic surgery among female (n=271) and male (n=71) medical students at 2 urban teaching institutions. Elective lectures and orthopedic literature were distributed via e-mail to the study participants. These materials included articles published in the medical literature, materials produced and distributed by the American Academy of Orthopaedic Surgeons, and Web sites providing educational materials. The primary outcome was the likelihood of application for orthopedic residency. We studied the influence of demographics, exposure, and attitudes on interest in pursuing an orthopedic career. Men had a significantly higher baseline level of interest in orthopedic surgery than women (P=.005). Younger age (P<.001) and personal (P<.001), independent (P<.001), and school (P=.023) exposures to orthopedics were significantly related to interest among women. At final follow-up, total personal exposures (P=.003) and total independent exposures (P<.001) in the form of our literature and lectures were correlated with final interest in women. Female interest was decreased by the long hours, physical demands, and predominantly male nature of the field. Early exposure to orthopedic educational resources may be useful in generating female interest. Perceptions and attitudes regarding orthopedic surgery must to be changed to attract the best and brightest minds, regardless of sex. Copyright © 2011, SLACK Incorporated.

Hydration behaviors of calcium silicate-based biomaterials.

PubMed

Lee, Yuan-Ling; Wang, Wen-Hsi; Lin, Feng-Huie; Lin, Chun-Pin

2017-06-01

Calcium silicate (CS)-based biomaterials, such as mineral trioxide aggregate (MTA), have become the most popular and convincing material used in restorative endodontic treatments. However, the commercially available CS-based biomaterials all contain different minor additives, which may affect their hydration behaviors and material properties. The purpose of this study was to evaluate the hydration behavior of CS-based biomaterials with/without minor additives. A novel CS-based biomaterial with a simplified composition, without mineral oxides as minor additives, was produced. The characteristics of this biomaterial during hydration were investigated using scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared (FTIR) spectrometry. The hydration behaviors of commercially available gray and white MTAs with mineral oxide as minor additives were also evaluated for reference. For all three test materials, the XRD analysis revealed similar diffraction patterns after hydration, but MTAs presented a significant decrease in the intensities of Bi 2 O 3 -related peaks. SEM results demonstrated similar porous microstructures with some hexagonal and facetted crystals on the outer surfaces. In addition, compared to CS with a simplified composition, the FTIR plot indicated that hydrated MTAs with mineral oxides were better for the polymerization of calcium silicate hydrate (CSH), presenting Si-O band shifting to higher wave numbers, and contained more water crystals within CSH, presenting sharper bands for O-H bending. Mineral oxides might not result in significant changes in the crystal phases or microstructures during the hydration of CS-based biomaterials, but these compounds affected the hydration behavior at the molecular level. Copyright © 2016. Published by Elsevier B.V.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corona, Edmundo

The Kolsky compression bar, or split Hopkinson pressure bar (SHPB), is an ex- perimental apparatus used to obtain the stress-strain response of material specimens at strain rates in the order of 10 2 to 10 4 1/s. Its operation and associated data re- duction are based on principles of one-dimensional wave propagation in rods. Second order effects such as indentation of the bars by the specimen and wave dispersion in the bars, however, can significantly affect aspects of the measured material response. Finite element models of the experimental apparatus were used here to demonstrate these two effects. A proceduremore » proposed by Safa and Gary (2010) to account for bar indentation was also evaluated and shown to improve the estimation of the strain in the bars significantly. The use of pulse shapers was also shown to alleviate the effects of wave dispersion. Combining the two can lead to more reliable results in Kolsky compression bar testing.« less

Comparison of fit accuracy and torque maintenance of zirconia and titanium abutments for internal tri-channel and external-hex implant connections.

PubMed

Siadat, Hakimeh; Beyabanaki, Elaheh; Mousavi, Niloufar; Alikhasi, Marzieh

2017-08-01

This in vitro study aimed to evaluate the effect of implant connection design (external vs. internal) on the fit discrepancy and torque loss of zirconia and titanium abutments. Two regular platform dental implants, one with external connection (Brånemark, Nobel Biocare AB) and the other with internal connection (Noble Replace, Nobel Biocare AB), were selected. Seven titanium and seven customized zirconia abutments were used for each connection design. Measurements of geometry, marginal discrepancy, and rotational freedom were done using video measuring machine. To measure the torque loss, each abutment was torqued to 35 Ncm and then opened by means of a digital torque wrench. Data were analyzed with two-way ANOVA and t-test at α=0.05 of significance. There were significant differences in the geometrical measurements and rotational freedom between abutments of two connection groups ( P <.001). Also, the results showed significant differences between titanium abutments of internal and external connection implants in terms of rotational freedom ( P <.001). Not only customized internal abutments but also customized external abutments did not have the exact geometry of prefabricated abutments ( P <.001). However, neither connection type ( P =.15) nor abutment material ( P =.38) affected torque loss. Abutments with internal connection showed less rotational freedom. However, better marginal fit was observed in externally connected abutments. Also, customized abutments with either connection could not duplicate the exact geometry of their corresponding prefabricated abutment. However, neither abutment connection nor material affected torque loss values.

Comparison of Manual Refraction Versus Autorefraction in 60 Diabetic Retinopathy Patients

PubMed Central

Shirzadi, Keyvan; Shahraki, Kourosh; Yahaghi, Emad; Makateb, Ali; Khosravifard, Keivan

2016-01-01

Aim: The purpose of the study was to evaluate the comparison of manual refraction versus autorefraction in diabetic retinopathy patients. Material and Methods: The study was conducted at the Be’sat Army Hospital from 2013-2015. In the present study differences between two common refractometry methods (manual refractometry and Auto refractometry) in diagnosis and follow up of retinopathy in patients affected with diabetes is investigated. Results: Our results showed that there is a significant difference in visual acuity score of patients between manual and auto refractometry. Despite this fact, spherical equivalent scores of two methods of refractometry did not show a significant statistical difference in the patients. Conclusion: Although use of manual refraction is comparable with autorefraction in evaluating spherical equivalent scores in diabetic patients affected with retinopathy, but in the case of visual acuity results from these two methods are not comparable. PMID:27703289

Radiation Detection at Borders for Homeland Security

NASA Astrophysics Data System (ADS)

Kouzes, Richard

2004-05-01

Countries around the world are deploying radiation detection instrumentation to interdict the illegal shipment of radioactive material crossing international borders at land, rail, air, and sea ports of entry. These efforts include deployments in the US and a number of European and Asian countries by governments and international agencies. Items of concern include radiation dispersal devices (RDD), nuclear warheads, and special nuclear material (SNM). Radiation portal monitors (RPMs) are used as the main screening tool for vehicles and cargo at borders, supplemented by handheld detectors, personal radiation detectors, and x-ray imaging systems. Some cargo contains naturally occurring radioactive material (NORM) that triggers "nuisance" alarms in RPMs at these border crossings. Individuals treated with medical radiopharmaceuticals also produce nuisance alarms and can produce cross-talk between adjacent lanes of a multi-lane deployment. The operational impact of nuisance alarms can be significant at border crossings. Methods have been developed for reducing this impact without negatively affecting the requirements for interdiction of radioactive materials of interest. Plastic scintillator material is commonly used in RPMs for the detection of gamma rays from radioactive material, primarily due to the efficiency per unit cost compared to other detection materials. The resolution and lack of full-energy peaks in the plastic scintillator material prohibits detailed spectroscopy. However, the limited spectroscopic information from plastic scintillator can be exploited to provide some discrimination. Energy-based algorithms used in RPMs can effectively exploit the crude energy information available from a plastic scintillator to distinguish some NORM. Whenever NORM cargo limits the level of the alarm threshold, energy-based algorithms produce significantly better detection probabilities for small SNM sources than gross-count algorithms. This presentation discusses experience with RPMs for interdiction of radioactive materials at borders.

Economic impact of corrosion and scaling problems in geothermal energy systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shannon, D.W.

Corrosion and scaling problems have a significant impact on geothermal plant economics. A power plant must amortize the capital investment over a 20-year period and achieve satisfactory operating efficiency to achieve financial success. Corrosion and scale incrustations have been encountered in all geothermal plants, and to various degrees, adversely affected plant life times and power output. Using published data this report analyzes known geothermal corrosion and scaling phenomena for significant cost impacts on plant design and operation. It has been necessary to speculate about causes and mechanisms in order to estimate impacts on conceptual geothermal plants. Silica is highly solublemore » in hot geothermal water and solubility decreases as water is cooled in a geothermal power plant. Calculations indicate as much as 30,000 tons/year could pass through a 100 MWe water cycle plant. The major cost impact will be on the reinjection well system where costs of 1 to 10 mills/kwhr of power produced could accrue to waste handling alone. On the other hand, steam cycle geothermal plants have a definite advantage in that significant silica problems will probably only occur in hot dry rock concepts, where steam above 250 C is produced. Calculation methods are given for estimating the required size and cost impact of a silica filtration plant and for sizing scrubbers. The choice of materials is significantly affected by the pH of the geothermal water, temperature, chloride, and H{sub s} contents. Plant concepts which attempt to handle acid waters above 180 C will be forced to use expensive corrosion resistant alloys or develop specialized materials. On the other hand, handling steam up to 500 C, and pH 9 water up to 180 C appears feasible using nominal cost steels, typical of today's geothermal plants. A number of factors affecting plant or component availability have been identified. The most significant is a corrosion fatigue problem in geothermal turbines at the Geyser's geothermal plant which is presently reducing plant output by about 10%. This is equivalent to over $3 million per year in increased oil consumption to replace the power. In the course of assessing the cost implications of corrosion and scaling problems, a number of areas of technological uncertainty were identified which should be considered in R and D planning in support of geothermal energy. Materials development with both laboratory and field testing will be necessary. The economic analysis on which this report is based was done in support of an AEC Division of Applied Technology program to assess the factors affecting geothermal plant economics. The results of this report are to be used to develop computer models of overall plant economics, of which corrosion and scaling problems are only a part. The translation of the economic analysis to the report which appears here, was done on AEC Special Studies Funds.« less

Production of lunar fragmental material by meteoroid impact.

NASA Technical Reports Server (NTRS)

Marcus, A. H.

1973-01-01

The rate of production of new fragmental lunar surface material is derived theoretically on the hypothesis that such material is excavated from a bedrock layer by meteoroid impacts. An overlaying regolith effectively shields the bedrock layer from small impacts, reducing the production rate of centimeter-sized and smaller blocks by a large factor. Logarithmic production rate curves for centimeter to motor-sized blocks are nonlinear for any regolith from centimeters to tens of meters in thickness, with small blocks relatively much less frequent for thicker (older) regoliths, suggesting the possibility of a statistical reverse bedding. Modest variations in the exponents of scaling laws for crater depth-diameter ratio and maximum block-diameter to crater diameter ratio are shown to have significant effects on the production rates. The production rate increases slowly with increasing size of the largest crater affecting the region.

Experimental Procedure for Warm Spinning of Cast Aluminum Components.

PubMed

Roy, Matthew J; Maijer, Daan M

2017-02-01

High performance, cast aluminum automotive wheels are increasingly being incrementally formed via flow forming/metal spinning at elevated temperatures to improve material properties. With a wide array of processing parameters which can affect both the shape attained and resulting material properties, this type of processing is notoriously difficult to commission. A simplified, light-duty version of the process has been designed and implemented for full-size automotive wheels. The apparatus is intended to assist in understanding the deformation mechanisms and the material response to this type of processing. An experimental protocol has been developed to prepare for, and subsequently perform forming trials and is described for as-cast A356 wheel blanks. The thermal profile attained, along with instrumentation details are provided. Similitude with full-scale forming operations which impart significantly more deformation at faster rates is discussed.

Experimental Procedure for Warm Spinning of Cast Aluminum Components

PubMed Central

Roy, Matthew J.; Maijer, Daan M.

2017-01-01

High performance, cast aluminum automotive wheels are increasingly being incrementally formed via flow forming/metal spinning at elevated temperatures to improve material properties. With a wide array of processing parameters which can affect both the shape attained and resulting material properties, this type of processing is notoriously difficult to commission. A simplified, light-duty version of the process has been designed and implemented for full-size automotive wheels. The apparatus is intended to assist in understanding the deformation mechanisms and the material response to this type of processing. An experimental protocol has been developed to prepare for, and subsequently perform forming trials and is described for as-cast A356 wheel blanks. The thermal profile attained, along with instrumentation details are provided. Similitude with full-scale forming operations which impart significantly more deformation at faster rates is discussed. PMID:28190063

Effects of chemical and biological warfare remediation agents on the materials of museum objects

NASA Astrophysics Data System (ADS)

Solazzo, C.; Erhardt, D.; Marte, F.; von Endt, D.; Tumosa, C.

In the fall of 2001, anthrax-contaminated letters were sent to public figures in the United States. Chemical and radiation treatments were employed to decontaminate exposed buildings, objects, and materials. These treatments are effective, but potentially damaging to exposed objects and materials. The recommended surface chemical treatments include solutions, gels, and foams of oxidizing agents such as peroxides or chlorine bleaching agents. Such oxidizing agents are effective against a wide range of hazardous chemical and biological agents. Knowing how these reagents affect various substrates would help to anticipate and to minimize any potential damage. We are examining the effects on typical museum materials of reagents likely to be used, including hydrogen peroxide, sodium hypochlorite, and potassium peroxymonosulfate. Results so far show significant changes in a number of materials. Surface corrosion was observed on metals such as copper, silver, iron, and brass. Color changes occurred with at least one reagent in about one-fourth of the dyed fabric swatches tested, and about half of the inks. Samples of aged yellowed paper are bleached. Effects varied with both the substrate and the tested reagent. The observed changes were generally less drastic than might have been expected. Enough materials were affected, though, to preclude the use of these reagents on museum objects unless no less drastic alternative is available. It appears that many objects of lesser intrinsic value can be treated without severe loss of properties or usefulness. For example, most documents should remain legible if the appropriate reagent is used. This work will provide a basis for determining which treatment is most appropriate for a specific situation and what consequences are to be expected from other treatments.

Final Report - Assessment of Potential Phosphate Ion-Cementitious Materials Interactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Naus, Dan J; Mattus, Catherine H; Dole, Leslie Robert

The objectives of this limited study were to: (1) review the potential for degradation of cementitious materials due to exposure to high concentrations of phosphate ions; (2) provide an improved understanding of any significant factors that may lead to a requirement to establish exposure limits for concrete structures exposed to soils or ground waters containing high levels of phosphate ions; (3) recommend, as appropriate, whether a limitation on phosphate ion concentration in soils or ground water is required to avoid degradation of concrete structures; and (4) provide a "primer" on factors that can affect the durability of concrete materials andmore » structures in nuclear power plants. An assessment of the potential effects of phosphate ions on cementitious materials was made through a review of the literature, contacts with concrete research personnel, and conduct of a "bench-scale" laboratory investigation. Results of these activities indicate that: no harmful interactions occur between phosphates and cementitious materials unless phosphates are present in the form of phosphoric acid; phosphates have been incorporated into concrete as set retarders, and phosphate cements have been used for infrastructure repair; no standards or guidelines exist pertaining to applications of reinforced concrete structures in high-phosphate environments; interactions of phosphate ions and cementitious materials has not been a concern of the research community; and laboratory results indicate similar performance of specimens cured in phosphate solutions and those cured in a calcium hydroxide solution after exposure periods of up to eighteen months. Relative to the "primer," a separate NUREG report has been prepared that provides a review of pertinent factors that can affect the durability of nuclear power plant reinforced concrete structures.« less

Ballistic impact resistance of selected organic ophthalmic lenses.

PubMed

Chou, B Ralph; Yuen, Gloria S-C; Dain, Stephen J

2011-11-01

The aim was to assess the impact resistance of coated and uncoated mid-index spectacle lens materials using the ballistic impact test. Nominally plano lenses of each material in three thicknesses were obtained. The lenses were flat edged to a 50 mm diameter. Each lens was impacted by a 6.35 mm steel ball. Impact velocities were selected using the Zippy Estimation by Sequential Testing protocol to determine the threshold fracture impact velocity. Threshold fracture impact velocity generally increased with thickness; however, there was a wide variation in performance among the various lens materials at each thickness. In all but two instances, the differences in impact velocity at each thickness of lens material were significant. Comparison of the data for CR39 and Hoya Phoenix with the results of earlier studies showed that the lens mounting is a significant factor. The fracture velocities found in the present study were significantly lower than the fracture velocities found when the lens edge is restrained in the mounting. A scratch resistant coating reduced the impact resistance of CR39. The effect of the antireflection coating on the fracture velocity depended on the nature of the base scratch-resistant coating. Mid-index lens materials of the same thickness show widely varying levels of impact resistance under the ballistic test. Impact resistance increases non-linearly with centre thickness. The lens mounting might affect the results of the ballistic impact test. The presence of 'cushion coatings' might enhance impact resistance. © 2011 The Authors. Clinical and Experimental Optometry © 2011 Optometrists Association Australia.

In vitro antibacterial activity of a novel resin-based pulp capping material containing the quaternary ammonium salt MAE-DB and Portland cement.

PubMed

Yang, Yanwei; Huang, Li; Dong, Yan; Zhang, Hongchen; Zhou, Wei; Ban, Jinghao; Wei, Jingjing; Liu, Yan; Gao, Jing; Chen, Jihua

2014-01-01

Vital pulp preservation in the treatment of deep caries is challenging due to bacterial infection. The objectives of this study were to synthesize a novel, light-cured composite material containing bioactive calcium-silicate (Portland cement, PC) and the antimicrobial quaternary ammonium salt monomer 2-methacryloxylethyl dodecyl methyl ammonium bromide (MAE-DB) and to evaluate its effects on Streptococcus mutans growth in vitro. The experimental material was prepared from a 2 : 1 ratio of PC mixed with a resin of 2-hydroxyethylmethacrylate, bisphenol glycerolate dimethacrylate, and triethylene glycol dimethacrylate (4 : 3 : 1) containing 5 wt% MAE-DB. Cured resin containing 5% MAE-DB without PC served as the positive control material, and resin without MAE-DB or PC served as the negative control material. Mineral trioxide aggregate (MTA) and calcium hydroxide (Dycal) served as commercial controls. S. mutans biofilm formation on material surfaces and growth in the culture medium were tested according to colony-forming units (CFUs) and metabolic activity after 24 h incubation over freshly prepared samples or samples aged in water for 6 months. Biofilm formation was also assessed by Live/Dead staining and scanning electron microscopy. S. mutans biofilm formation on the experimental material was significantly inhibited, with CFU counts, metabolic activity, viability staining, and morphology similar to those of biofilms on the positive control material. None of the materials affected bacterial growth in solution. Contact-inhibition of biofilm formation was retained by the aged experimental material. Significant biofilm formation was observed on MTA and Dycal. The synthesized material containing HEMA-BisGMA-TEGDMA resin with MAE-DB as the antimicrobial agent and PC to support mineralized tissue formation inhibited S. mutans biofilm formation even after aging in water for 6 months, but had no inhibitory effect on bacteria in solution. Therefore, this material shows promise as a pulp capping material for vital pulp preservation in the treatment of deep caries.

The Effect of Substrate Microstructure on the Heat-Affected Zone Size in Sn-Zn Alloys Due to Adjoining Ni-Al Reactive Multilayer Foil Reaction

DOE PAGES

Hooper, R. J.; Adams, D. P.; Hirschfeld, D.; ...

2015-08-05

The rapid release of energy from reactive multilayer foils can create extreme local temperature gradients near substrate materials. To fully exploit the potential of these materials, a better understanding of the interaction between the substrate or filler material and the foil is needed. In particular, this work investigates how variations in local properties within the substrate (i.e. differences between properties in constituent phases) can affect heat transport into the substrate. Furthermore, this can affect the microstructural evolution observed within the substrate, which may affect the final joint properties. The effect of the initial substrate microstructure on microstructural evolution within themore » heat-affected zone is evaluated experimentally in two Sn-Zn alloys and numerical techniques are utilized to inform the analysis.« less

Tendon material properties vary and are interdependent among turkey hindlimb muscles

PubMed Central

Matson, Andrew; Konow, Nicolai; Miller, Samuel; Konow, Pernille P.; Roberts, Thomas J.

2012-01-01

SUMMARY The material properties of a tendon affect its ability to store and return elastic energy, resist damage, provide mechanical feedback and amplify or attenuate muscle power. While the structural properties of a tendon are known to respond to a variety of stimuli, the extent to which material properties vary among individual muscles remains unclear. We studied the tendons of six different muscles in the hindlimb of Eastern wild turkeys to determine whether there was variation in elastic modulus, ultimate tensile strength and resilience. A hydraulic testing machine was used to measure tendon force during quasi-static lengthening, and a stress–strain curve was constructed. There was substantial variation in tendon material properties among different muscles. Average elastic modulus differed significantly between some tendons, and values for the six different tendons varied nearly twofold, from 829±140 to 1479±106 MPa. Tendons were stretched to failure, and the stress at failure, or ultimate tensile stress, was taken as a lower-limit estimate of tendon strength. Breaking tests for four of the tendons revealed significant variation in ultimate tensile stress, ranging from 66.83±14.34 to 112.37±9.39 MPa. Resilience, or the fraction of energy returned in cyclic length changes was generally high, and one of the four tendons tested was significantly different in resilience from the other tendons (range: 90.65±0.83 to 94.02±0.71%). An analysis of correlation between material properties revealed a positive relationship between ultimate tensile strength and elastic modulus (r2=0.79). Specifically, stiffer tendons were stronger, and we suggest that this correlation results from a constrained value of breaking strain, which did not vary significantly among tendons. This finding suggests an interdependence of material properties that may have a structural basis and may explain some adaptive responses observed in studies of tendon plasticity. PMID:22771746

Tendon material properties vary and are interdependent among turkey hindlimb muscles.

PubMed

Matson, Andrew; Konow, Nicolai; Miller, Samuel; Konow, Pernille P; Roberts, Thomas J

2012-10-15

The material properties of a tendon affect its ability to store and return elastic energy, resist damage, provide mechanical feedback and amplify or attenuate muscle power. While the structural properties of a tendon are known to respond to a variety of stimuli, the extent to which material properties vary among individual muscles remains unclear. We studied the tendons of six different muscles in the hindlimb of Eastern wild turkeys to determine whether there was variation in elastic modulus, ultimate tensile strength and resilience. A hydraulic testing machine was used to measure tendon force during quasi-static lengthening, and a stress-strain curve was constructed. There was substantial variation in tendon material properties among different muscles. Average elastic modulus differed significantly between some tendons, and values for the six different tendons varied nearly twofold, from 829±140 to 1479±106 MPa. Tendons were stretched to failure, and the stress at failure, or ultimate tensile stress, was taken as a lower-limit estimate of tendon strength. Breaking tests for four of the tendons revealed significant variation in ultimate tensile stress, ranging from 66.83±14.34 to 112.37±9.39 MPa. Resilience, or the fraction of energy returned in cyclic length changes was generally high, and one of the four tendons tested was significantly different in resilience from the other tendons (range: 90.65±0.83 to 94.02±0.71%). An analysis of correlation between material properties revealed a positive relationship between ultimate tensile strength and elastic modulus (r(2)=0.79). Specifically, stiffer tendons were stronger, and we suggest that this correlation results from a constrained value of breaking strain, which did not vary significantly among tendons. This finding suggests an interdependence of material properties that may have a structural basis and may explain some adaptive responses observed in studies of tendon plasticity.

Decoration of wide bandgap semiconducting materials for enhancing photoelectrochemical efficiency of PEC systems.

NASA Astrophysics Data System (ADS)

Bakranov, N.; Zhabaikhanov, A.; Kudaibergenov, S.; Ibraev, N.

2018-03-01

The production of photoanodes based on wide-band gap materials such as TiO2 is economically viable because of the low cost of synthesis methods. Contrary to economic aspects, wide-band gap semiconductor materials have a significant disadvantage due to low sensitivity to photons of visible light. To increase the photoactive parameters of the material of the electrodes in the visible range, the methods for decorating nanomasses of titanium dioxide by narrow-gap semiconductors are used. One of the most suitable narrow-gap semiconductor materials are CdS and Fe2O3. Controlled deposition of such materials on wide-gap semiconductors allows to regulate both the diffusion time of charge carriers and the band structure of TiO2/Fe2O3 and TiO2/CdS composites. The dimensions of the structure of the photoelectrode material of the cell have a large influence on the characteristics of the photocatalyst created. Thus, in the hematite structures of nanometre dimension, the rate of recombination of charge carriers fades away in comparison with bulk structures. Reducing the size of CdS structures also positively affects the nature of the photocatalytic reaction.

Adjoint-based optimization of mechanical performance in polycrystalline materials and structures through texture control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gu, Grace; Brown, Judith Alice; Bishop, Joseph E.

The texture of a polycrystalline material refers to the preferred orientation of the grains within the material. In metallic materials, texture can significantly affect the mechanical properties such as elastic moduli, yield stress, strain hardening, and fracture toughness. Recent advances in additive manufacturing of metallic materials offer the possibility in the not too distant future of controlling the spatial variation of texture. In this work, we investigate the advantages, in terms of mechanical performance, of allowing the texture to vary spatially. We use an adjoint-based gradient optimization algorithm within a finite element solver (COMSOL) to optimize several engineering quantities ofmore » interest in a simple structure (hole in a plate) and loading (uniaxial tension) condition. As a first step to general texture optimization, we consider the idealized case of a pure fiber texture in which the homogenized properties are transversely isotropic. In this special case, the only spatially varying design variables are the three Euler angles that prescribe the orientation of the homogenized material at each point within the structure. This work paves a new way to design metallic materials for tunable mechanical properties at the microstructure level.« less

Effects of adsorptive properties of biofilter packing materials on toluene removal.

PubMed

Oh, Dong Ik; Song, Jihyeon; Hwang, Sun Jin; Kim, Jae Young

2009-10-15

Various adsorptive materials, including granular activated carbon (GAC) and ground tire rubber (GTR), were mixed with compost in biofilters used for treating gaseous toluene, and the effects of the mixtures on the stability of biofilter performance were investigated. A transient loading test demonstrated that a sudden increase in inlet toluene loading was effectively attenuated in the compost/GAC biofilter, which was the most significant advantage of adding adsorptive materials to the biofilter packing media. Under steady conditions with inlet toluene loading rates of 18.8 and 37.5 g/m(3)/h, both the compost and the compost/GAC biofilters achieved overall toluene removal efficiencies greater than 99%. In the compost/GAC mixture, however, biodegradation activity declined as the GAC mass fraction increased. Because of the low water-holding capacity of GTR, the compost/ground tire mixture did not show a significant improvement in toluene removal efficiency throughout the entire operational period. Furthermore, nitrogen limitations affected system performance in all the biofilters, but an external nitrogen supply resulted in the recovery of the toluene removal efficiency only in the compost biofilter during the test periods. Consequently, the introduction of excessive adsorptive materials was unfavorable for long-term performance, suggesting that the mass ratio of the adsorptive materials in such mixtures should be carefully selected to achieve high and steady biofilter performance.

Sorting it out: bedding particle size and nesting material processing method affect nest complexity.

PubMed

Robinson-Junker, Amy; Morin, Amelia; Pritchett-Corning, Kathleen; Gaskill, Brianna N

2017-04-01

As part of routine husbandry, an increasing number of laboratory mice receive nesting material in addition to standard bedding material in their cages. Nesting material improves health outcomes and physiological performance in mice that receive it. Providing usable nesting material uniformly and efficiently to various strains of mice remains a challenge. The aim of this study was to determine how bedding particle size, method of nesting material delivery, and processing of the nesting material before delivery affected nest building in mice of strong (BALB/cAnNCrl) and weak (C3H/HeNCrl) gathering abilities. Our data suggest that processing nesting material through a grinder in conjunction with bedding material, although convenient for provision of bedding with nesting material 'built-in', negatively affects the integrity of the nesting material and subsequent nest-building outcomes. We also found that C3H mice, previously thought to be poor nest builders, built similarly scored nests to those of BALB/c mice when provided with unprocessed nesting material. This was true even when nesting material was mixed into the bedding substrate. We also observed that when nesting material was mixed into the bedding substrate, mice of both strains would sort their bedding by particle size more often than if it were not mixed in. Our findings support the utility of the practice of distributing nesting material mixed in with bedding substrate, but not that of processing the nesting material with the bedding in order to mix them.

The effect of impression volume and double-arch trays on the registration of maximum intercuspation.

PubMed

Hahn, Sara M; Millstein, Philip L; Kinnunen, Taru H; Wright, Robert F

2009-12-01

The type of double-arch trays used may affect occlusion. The purpose of this study was to determine what effect, if any, double-arch tray design and impression material volume had on the registration of maximum intercuspation (MI). Quadrant impressions were made on articulated fracture-resistant dental casts mounted in maximum intercuspation occlusion. Three types of sideless double-arch impression trays were used: First Bite with nylon webbing, Sultan's 3-Way with double crosshatch webbing, and Premium's 3-in-1 Tray with single crosshatch webbing. Vinyl polysiloxane impression material (Aquasil Ultra Rigid Fast Set) was distributed at 2 different volumes (5.4 ml and 8.3 ml), and 60 impressions were made (n=10). A weight of 1.2 kg was placed on the upper arm of an Artex articulator, ensuring complete closure. The impressions were allowed to polymerize for 5 minutes. After polymerization, specimens were placed on a light box, and a camera set at a fixed distance was used to capture the light transmission that was projected through the impression material. The camera transferred the information to an image analysis program (ImageJ). This system allowed the different amounts of light projected through the impression to be translated into a gray scale value (GSV), which was assigned a thickness value, in millimeters, of a specified occlusal contact area. To assess reliability of the experimental design, 10 control impressions were made by directly applying impression material onto the typodont. These were analyzed in the same manner as the impressions made with trays. A 2-way ANOVA comparing volume by tray type was used (alpha=.05). This was followed by a Tukey HSD test. There was no main effect for volume of impression material (P=.71). Tray type was significantly different (P<.001). Impressions made with Sultan trays were significantly less accurate than impressions made with First Bite or Premium impression trays. The Premium tray type had the highest mean (SD) GSV, 179.8 (8.1), significantly higher than First Bite (164.7 (19.8); P<.001) or Sultan (82.8 (7.4); P<.001) trays. This in vitro study demonstrated that certain trays hinder closure into MI, which may negatively affect the accuracy of record making.

The influence of multiple firing on thermal contraction of ceramic materials used for the fabrication of layered all-ceramic dental restorations.

PubMed

Isgrò, Giuseppe; Kleverlaan, Cornelis J; Wang, Hang; Feilzer, Albert J

2005-06-01

During the production of layered all-ceramic restorations transient and/or residual thermal stresses may be formed which may affect a restoration's longevity. The aim of this study was to evaluate the influence of multiple firings on the thermal behavior of veneering porcelains and a ceramic core. The materials tested were: Empress 2 Core, Empress 2 Veneer and Eris glass-ceramics, Carrara Vincent and an experimental leucite-based veneering porcelain, Vitadur-Alpha aluminous porcelain, and two porcelains designed for titanium (i.e. Duceratin Dentine and Enamel). The thermal contraction coefficient of the materials was measured by means of dilatometery. The thermal contraction coefficient was measured during cooling and calculated over the temperature range of 450-20 degrees C by linear regression. One and two-way analysis of variance together with Tukey post-hoc tests were used as statistical analysis. Repeated firing affects the thermal contraction coefficients of Empress 2 Veneer, Carrara Vincent porcelain and the experimental porcelain. The thermal contraction coefficients of Empress 2 Core were significantly different from Vitadur-Alpha, Carrara Vincent, experimental porcelain, and Duceratin porcelains. The contraction coefficients of Empress 2 Veneer and Eris were closest to that of Empress 2 Core. The Empress 2 Core and Eris glass-ceramics, the aluminous porcelain and Duceratin porcelains showed better thermal stability after repeated firing than leucite porcelains. It can be concluded that due to the thermal stability of glass-ceramic materials, layered all-ceramic restorations of these materials may perform better.

Micrometeoroid/space debris effects on materials

NASA Technical Reports Server (NTRS)

Zwiener, James M.; Finckenor, Miria M.

1993-01-01

The Long Duration Exposure Facility (LDEF) micrometeoroid/space debris impact data has been reduced in terms that are convenient for evaluating the overall quantitative effect on material properties. Impact crater flux has been evaluated as a function of angle from velocity vector and as a function of crater size. This data is combined with spall data from flight and ground testing to calculate effective solar absorption and emittance values versus time. Results indicate that the surface damage from micrometeoroid/space debris does not significantly affect the overall surface optical thermal physical properties. Of course the local damage around impact craters radically alter optical properties. Damage to composites and solar cells on an overall basis was minimal.

Characterization of Subsurface Defects in Ceramic Rods by Laser Scattering and Fractography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, J. M.; Sun, J. G.; Andrews, M. J.

2006-03-06

Silicon nitride ceramics are leading materials being evaluated for valve train components in diesel engine applications. The surface and subsurface defects and damage induced by surface machining can significantly affect component strength and lifetime. In this study, a nondestructive evaluation (NDE) technique based upon laser scattering has been utilized to analyze eight transversely ground silicon nitride cylindrical rods before fracture tests. The fracture origins (machining cracks or material-inherent flaws) identified by fractography after fracture testing were correlated with laser scattering images. The results indicate that laser scattering is able to identify possible fracture origin in the silicon nitride subsurface withoutmore » the need for destructive fracture tests.« less

The Effect of Arch Height and Material Hardness of Personalized Insole on Correction and Tissues of Flatfoot.

PubMed

Su, Shonglun; Mo, Zhongjun; Guo, Junchao; Fan, Yubo

2017-01-01

Flat foot is one of the common deformities in the youth population, seriously affecting the weight supporting and daily exercising. However, there is lacking of quantitative data relative to material selection and shape design of the personalized orthopedic insole. This study was to evaluate the biomechanical effects of material hardness and support height of personalized orthopedic insole on foot tissues, by in vivo experiment and finite element modeling. The correction of arch height increased with material hardness and support height. The peak plantar pressure increased with the material hardness, and these values by wearing insoles of 40° were apparently higher than the bare feet condition. Harder insole material results in higher stress in the joint and ligament stress than softer material. In the calcaneocuboid joint, the stress increased with the arch height of insoles. The material hardness did not apparently affect the stress in the ankle joints, but the support heights of insole did. In general, insole material and support design are positively affecting the correction of orthopedic insole, but negatively resulting in unreasonable stress on the stress in the joint and ligaments. There should be an integration of improving correction and reducing stress in foot tissues.

Incidence and risk factors for post-traumatic stress disorder in a population affected by a severe flood.

PubMed

Fontalba-Navas, A; Lucas-Borja, M E; Gil-Aguilar, V; Arrebola, J P; Pena-Andreu, J M; Perez, J

2017-03-01

We aimed to study the risk of developing post-traumatic stress disorder (PTSD) symptoms in people who resided in an affected area by an extremely severe flood, and sociodemographic risk factors associated with this condition. A geographic information system (GIS) was used to distribute the rainfall data. A case-control study was developed to study the relationship between PTSD and sociodemographic risk factors. To delineate the areas affected by the flood and the intensity of this rainfall in comparison with historical hydrological data, we employed geographical information systems (GIS). Then, we recruited a representative sample of the affected population and another population sample that lived at the time of this disaster in adjacent geographical areas that were not affected. Both groups were randomly selected in primary care practices, from December 1st 2012 to January 31st 2013. All participants, 70 from the affected areas and 91 from the non-affected, filled a sociodemographic questionnaire and the trauma questionnaire (TQ) to identify and rate PTSD symptoms. Our GIS analysis confirmed that the amount of precipitation in 2012 in the areas affected by the flood was exceptionally high compared with historical average rainfall data (461l per square metre vs 265). Individuals who resided in the affected areas at the time of the flood were at much higher risk of developing PTSD symptoms (OR: 8.18; 95% CI: 3.99-17.59) than those living in adjacent, non-affected localities. Among the sociodemographic variables included in this study, only material and financial losses were strongly associated with the onset of PTSD (P < 0.001). Physical risk during this life-threatening catastrophe also indicated a positive correlation with later development of PTSD symptoms; however, it did not reach statistical significance (P = 0.06). Populations affected by severe floods may suffer an increase of PTSD symptoms in the following months. This finding, along with the importance of material losses as a predictor for such disorder, may help develop effective plans to minimize the negative impact of these natural disasters on public health. Copyright © 2016 The Author(s). Published by Elsevier Ltd.. All rights reserved.

Extending brain-training to the affective domain: increasing cognitive and affective executive control through emotional working memory training.

PubMed

Schweizer, Susanne; Hampshire, Adam; Dalgleish, Tim

2011-01-01

So-called 'brain-training' programs are a huge commercial success. However, empirical evidence regarding their effectiveness and generalizability remains equivocal. This study investigated whether brain-training (working memory [WM] training) improves cognitive functions beyond the training task (transfer effects), especially regarding the control of emotional material since it constitutes much of the information we process daily. Forty-five participants received WM training using either emotional or neutral material, or an undemanding control task. WM training, regardless of training material, led to transfer gains on another WM task and in fluid intelligence. However, only brain-training with emotional material yielded transferable gains to improved control over affective information on an emotional Stroop task. The data support the reality of transferable benefits of demanding WM training and suggest that transferable gains across to affective contexts require training with material congruent to those contexts. These findings constitute preliminary evidence that intensive cognitively demanding brain-training can improve not only our abstract problem-solving capacity, but also ameliorate cognitive control processes (e.g. decision-making) in our daily emotive environments.

Premature mortality due to social and material deprivation in Nova Scotia, Canada.

PubMed

Saint-Jacques, Nathalie; Dewar, Ron; Cui, Yunsong; Parker, Louise; Dummer, Trevor Jb

2014-10-25

Inequalities in health attributable to inequalities in society have long been recognized. Typically, those most privileged experience better health, regardless of universal access to health care. Associations between social and material deprivation and mortality from all causes of death--a measure of population health, have been described for some regions of Canada. This study further examines the link between deprivation and health, focusing on major causes of mortality for both rural and urban populations. In addition, it quantifies the burden of premature mortality attributable to social and material deprivation in a Canadian setting where health care is accessible to all. The study included 35,266 premature deaths (1995-2005), grouped into five causes and aggregated over census dissemination areas. Two indices of deprivation (social and material) were derived from six socioeconomic census variables. Premature mortality was modeled as a function of these deprivation indices using Poisson regression. Premature mortality increased significantly with increasing levels of social and material deprivation. The impact of material deprivation on premature mortality was similar in urban and rural populations, whereas the impact of social deprivation was generally greater in rural populations. There were a doubling in premature mortality for those experiencing a combination of the most extreme levels of material and social deprivation. Socioeconomic deprivation is an important determinant of health equity and affects every segment of the population. Deprivation accounted for 40% of premature deaths. The 4.3% of the study population living in extreme levels of socioeconomic deprivation experienced a twofold increased risk of dying prematurely. Nationally, this inequitable risk could translate into a significant public health burden.

Detection of diisocyanates in nesting material associated with mortality in pigeon chicks.

PubMed

Mukai, Motoko; Woods, Leslie W; Stump, Samuel; Ebel, Joseph G; Levitt, Ariana S; Frey, Margaret W; Smith, Jeanne; Uzal, Francisco A; Poppenga, Robert H; Puschner, Birgit

2014-03-01

Diisocyanates, commonly used in the production of polyurethane foams, paints, elastomers, varnishes, and coatings, are considered among the most hazardous inhalation toxicants. The present report describes 2 unusual cases of mortality in pigeon chicks associated with nesting material contaminated by diisocyanates. Case 1 was submitted by a racing pigeon breeder who had lost all the hatchlings (n = 125) following replacement of the nesting material with a different lot. All adult birds appeared healthy, and hatchability was not significantly affected, but hatchlings became lethargic and dyspneic after a day of hatch. At necropsy, dark wet lungs were found in the hatchlings. Case 2 was submitted by a show-roller pigeon breeder. In this case, the owner reported lower hatchability, and all hatchlings (approximately 100) died within 2 days of hatching with clinical signs similar to the first case. Necropsy did not reveal any significant findings. For both cases, nesting materials were screened for toxic compounds using gas chromatography-mass spectrometry. Toluene-2,4-diisocyanate (approximately 190-290 ppm) and 4,4'-methylene diphenyl diisocyanate (unquantified) were detected in the nesting pads. While there is very limited information on toxicosis in birds, there are reports of inhalant exposure of diisocyanates causing pulmonary edema and death in various mammalian species. Although cause-effect relationship of mortality and the nesting material was not established in the present cases, the presence of toxic compounds in the nesting materials is a cause for concern. Further investigation is needed to determine the prevalence and toxicity of diisocyanates-contaminated nesting material in avian species.

28 CFR 55.15 - Affected activities.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) IMPLEMENTATION OF THE PROVISIONS OF THE VOTING RIGHTS ACT REGARDING LANGUAGE MINORITY GROUPS Minority Language Materials and Assistance § 55.15 Affected... registration or voting notices, forms, instructions, assistance, or other materials or information relating to...

28 CFR 55.15 - Affected activities.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) IMPLEMENTATION OF THE PROVISIONS OF THE VOTING RIGHTS ACT REGARDING LANGUAGE MINORITY GROUPS Minority Language Materials and Assistance § 55.15 Affected... registration or voting notices, forms, instructions, assistance, or other materials or information relating to...

Predictors of men's sexual response to erotic film stimuli: the role of affect and self-reported thoughts.

PubMed

Oliveira, Cátia; Laja, Pedro; Carvalho, Joana; Quinta Gomes, Ana; Vilarinho, Sandra; Janssen, Erick; Nobre, Pedro J

2014-11-01

Both emotions and cognitions seem to play a role in determining sexual arousal. However, no studies to date have tested the effects of self-reported thoughts on subjective sexual arousal and genital response using psychophysiological methods. The aim of the present study was to evaluate the role of self-reported thoughts and affect during exposure to erotic material in predicting subjective and genital responses in sexually healthy men. Twenty-seven men were presented with two explicit films, and genital responses, subjective sexual arousal, self-reported thoughts, and positive and negative affect were assessed. Men's genital responses, subjective sexual arousal, affective responses, and self-reported thoughts during exposure to sexual stimulus were measured. Regression analyses revealed that genital responses were predicted by self-reported thoughts (explaining 20% of the variance) but not by affect during exposure to erotic films. On the other hand, subjective sexual arousal was significantly predicted by both positive and negative affect (explaining 18% of the variance) and self-reported thoughts (explaining 37% of the variance). Follow-up analyses using the single predictors showed that "sexual arousal thoughts" were the only significant predictor of subjective response (β = 0.64; P < 0.01) and that "distracting/disengaging thoughts" were the best predictor of genital response (β = -0.51; P < 0.05). The findings of this study suggest that both affect and sexual arousal thoughts play an important role in men's subjective sexual response, whereas genital response seems to be better predicted by distracting thoughts. © 2014 International Society for Sexual Medicine.

Controlling mechanical properties of cell-laden hydrogels by covalent incorporation of graphene oxide.

PubMed

Cha, Chaenyung; Shin, Su Ryon; Gao, Xiguang; Annabi, Nasim; Dokmeci, Mehmet R; Tang, Xiaowu Shirley; Khademhosseini, Ali

2014-02-12

Graphene-based materials are useful reinforcing agents to modify the mechanical properties of hydrogels. Here, an approach is presented to covalently incorporate graphene oxide (GO) into hydrogels via radical copolymerization to enhance the dispersion and conjugation of GO sheets within the hydrogels. GO is chemically modified to present surface-grafted methacrylate groups (MeGO). In comparison to GO, higher concentrations of MeGO can be stably dispersed in a pre-gel solution containing methacrylated gelatin (GelMA) without aggregation or significant increase in viscosity. In addition, the resulting MeGO-GelMA hydrogels demonstrate a significant increase in fracture strength with increasing MeGO concentration. Interestingly, the rigidity of the hydrogels is not significantly affected by the covalently incorporated GO. Therefore, this approach can be used to enhance the structural integrity and resistance to fracture of the hydrogels without inadvertently affecting their rigidity, which is known to affect the behavior of encapsulated cells. The biocompatibility of MeGO-GelMA hydrogels is confirmed by measuring the viability and proliferation of the encapsulated fibroblasts. Overall, this study highlights the advantage of covalently incorporating GO into a hydrogel system, and improves the quality of cell-laden hydrogels. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Impact Verification of Aerogel Insulation Paint on Historic Brick Facades

NASA Astrophysics Data System (ADS)

Ganobjak, Michal; Kralova, Eva

2017-10-01

Increasing the sustainability of existing buildings is being motivated by reduction of their energy demands. It is the above all the building envelope and its refurbishment by substitution or addition of new materials that makes the opportunity for reduction of energy consumption. A special type of refurbishment is conservation of historical buildings. Preservation of historic buildings permits also application of innovative methods and materials in addition to the original materials if their effects are known and the gained experience ensures their beneficial effect. On the market, there are new materials with addition of silica aerogel in various forms of products. They are also potentially useful in conservation of monuments. However, the effects of aerogel application in these cases are not known. For refurbishment is commercially available additional transparent insulation paint - Nansulate Clear Coat which is containing aerogel and can be used for structured surfaces such as bricks. A series of experiments examined the thermo-physical manifestation of an ultra-thin insulation coating of Nansulate Clear Coat containing silica aerogel on a brick facade. The experiments of active and passive thermography have observed effects of application on the small-scale samples of the brick façade of a protected historical building. Through a series of experiments were measured thermal insulation effect and influence on the aesthetic characteristics such as change in colour and gloss. The treated samples were compared to a reference. Results have shown no thermal-insulating manifestation of the recommended three layers of insulation paint. The three layers recommended by the manufacturer did not significantly affect the appearance of the brick facade. Color and gloss were not significantly changed. Experiments showed the absence of thermal insulation effect of Nansulate transparent triple coating. The thermal insulation effect could likely be reached by more layers of application, which, on the other hand may be unacceptable on the heritage conservation because of number of applications, time demand and financial costs. The effects of multiple layers on heritage attributes were not researched. Extrapolating the measured results, it can be expected that application of more than three layers of paint can significantly affect the aesthetic characteristics of the monument such as gloss and colours of historic brick facades. Due to specific material consistence of historic architecture and new insulation paint materials on the market, it is recommended to provide independent laboratory testing and on-site tests on facades of historic buildings in cooperation with the Monument Protection Board.

Dynamic mechanical thermal analysis of hypromellose 2910 free films.

PubMed

Cespi, Marco; Bonacucina, Giulia; Mencarelli, Giovanna; Casettari, Luca; Palmieri, Giovanni Filippo

2011-10-01

It is common practice to coat oral solid dosage forms with polymeric materials for controlled release purposes or for practical and aesthetic reasons. Good knowledge of thermo-mechanical film properties or their variation as a function of polymer grade, type and amount of additives or preparation method is of prime importance in developing solid dosage forms. This work focused on the dynamic mechanical thermal characteristics of free films of hypromellose 2910 (also known as HPMC), prepared using three grades of this polymer from two different manufacturers, in order to assess whether polymer chain length or origin affects the mechanical or thermo-mechanical properties of the final films. Hypromellose free films were obtained by casting their aqueous solutions prepared at a specific concentrations in order to obtain the same viscosity for each. The films were stored at room temperature until dried and then examined using a dynamic mechanical analyser. The results of the frequency scans showed no significant differences in the mechanical moduli E' and E″ of the different samples when analysed at room temperature; however, the grade of the polymer affected material transitions during the heating process. Glass transition temperature, apparent activation energy and fragility parameters depended on polymer chain length, while the material brand showed little impact on film performance. Copyright © 2011 Elsevier B.V. All rights reserved.

Ultra-fine grained microstructure of metastable beta Ti-15Mo alloy and its effects on the phase transformations

NASA Astrophysics Data System (ADS)

Václavová, K.; Stráský, J.; Zháňal, P.; Veselý, J.; Polyakova, V.; Semenova, I.; Janeček, M.

2017-05-01

Processing of metastable titanium alloys by severe plastic deformation provides an opportunity to achieve exceptional grain refinement, to enhance the strength and to affect phase transformations occurring during thermal treatment. The main aim of this study is to investigate the microstructure of ultra-fine grained (UFG) material and effect of microstructural changes on phase transformations in metastable β-Ti alloy Ti-15Mo. Metastable β-Ti alloys are currently the most studied Ti-based materials with prospective use in medicine. Ti-15Mo alloy after solution treatment contains metastable β-phase. Metastable ω-phase and stable α-phase particles are formed upon annealing,. Solution treated Ti-15Mo alloy was deformed by high pressure torsion (HPT) at room temperature. Severely deformed structure after HPT with grain size of ~200 nm was studied by transmission electron microscopy. In-situ electrical resistance measurements showed significant changes in undergoing phase transformations when compared to coarse-grained (CG) material. Scanning electron microscopy revealed heterogeneous precipitation of α-particles at grain boundaries (GB). Due to the high density of GBs in UFG structure, these precipitates are very fine and equiaxed. The study demonstrates that SPD is capable of enhancing mechanical properties due to grain refinement and via affecting precipitation processes in metastable β-Ti alloys.

Effect of Porosity of Alumina and Zirconia Ceramics toward Pre-Osteoblast Response

PubMed Central

Hadjicharalambous, Chrystalleni; Prymak, Oleg; Loza, Kateryna; Buyakov, Ales; Kulkov, Sergei; Chatzinikolaidou, Maria

2015-01-01

It is acknowledged that cellular responses are highly affected by biomaterial porosity. The investigation of this effect is important for the development of implanted biomaterials that integrate with bone tissue. Zirconia and alumina ceramics exhibit outstanding mechanical properties and are among the most popular implant materials used in orthopedics, but few data exist regarding the effect of porosity on cellular responses to these materials. The present study investigates the effect of porosity on the attachment and proliferation of pre-osteoblastic cells on zirconia and alumina. For each composition, ceramics of three different porosities are fabricated by sintering, and characterized using scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray powder diffraction. Cell proliferation is quantified, and microscopy is employed to qualitatively support the proliferation results and evaluate cell morphology. Cell adhesion and metabolic activity are found comparable among low porosity zirconia and alumina. In contrast, higher porosity favors better cell spreading on zirconia and improves growth, but does not significantly affect cell response on alumina. Between the highest porosity materials, cell response on zirconia is found superior to alumina. Results show that an average pore size of ~150 μm and ~50% porosity can be considered beneficial to cellular growth on zirconia ceramics. PMID:26579516

Below room temperature: How the photocatalytic activity of dense and mesoporous TiO2 coatings is affected

NASA Astrophysics Data System (ADS)

Cedillo-González, Erika Iveth; Riccò, Raffaele; Costacurta, Stefano; Siligardi, Cristina; Falcaro, Paolo

2018-03-01

Different parameters such as morphology, porosity, crystalline phase or doping agents affect the self-cleaning performance of photocatalytic TiO2-based coatings. However, also environmental conditions have been found to play a major role on the photocatalytic self-cleaning property. Substrate temperature is a significant environmental variable that can drastically affect this process. This variable becomes of great importance especially for outdoor applications: many self-cleaning photocatalytic materials have been designed to be exposed to outdoor environments and consequently, can be exposed to variable temperatures depending on the season of the year and the typical weather of the geographical zone. Thus, understanding the influence of the most common outdoor temperatures on the self-cleaning performance of TiO2-based coatings is essential for the fabrication of any kind of photocatalytic self-cleaning materials (fabricated by coating technology) that is expected to be subjected to outdoor environments. In this work, the photocatalytic activity was studied by Fourier Transformed Infrared (FTIR) Spectroscopy varying the temperature in the 0 to 30 °C range for dense and mesoporous TiO2 coatings. The temperature conditions at which these coatings present better performances were identified, providing a deeper insight for the practical application of TiO2-based self-cleaning coatings.

Shellac/nanoparticles dispersions as protective materials for wood

NASA Astrophysics Data System (ADS)

Weththimuni, Maduka L.; Capsoni, Doretta; Malagodi, Marco; Milanese, Chiara; Licchelli, Maurizio

2016-12-01

Wood is a natural material that finds numerous and widespread applications, but is subject to different decay processes. Surface coating is the most common method used to protect wood against deterioration and to improve and stabilize its distinctive appearance. Shellac is a natural resin that has been widely used as a protective material for wooden artefacts (e.g. furniture, musical instruments), due to its excellent properties. Nevertheless, diffusion of shellac-based varnishes has significantly declined during the last decades, because of some limitations such as the softness of the coating, photo-degradation, and sensitivity to alcoholic solvents and to pH variations. In the present study, different inorganic nanoparticles were dispersed into dewaxed natural shellac and the resulting materials were investigated even after application on wood specimens in order to assess variations of the coating properties. Analyses performed by a variety of experimental techniques have shown that dispersed nanoparticles do not significantly affect some distinctive and desirable features of the shellac varnish such as chromatic aspect, film-forming ability, water repellence, and adhesion. On the other hand, the obtained results suggested that some weak points of the coating, such as low hardness and poor resistance to UV-induced ageing, can be improved by adding ZrO2 and ZnO nanoparticles, respectively.

Effect of filler properties in composite resins on light transmittance characteristics and color.

PubMed

Arikawa, Hiroyuki; Kanie, Takahito; Fujii, Koichi; Takahashi, Hideo; Ban, Seiji

2007-01-01

The purpose of this investigation was to examine the effect of filler particle size and shape as well as filler content on light transmittance characteristics and color of experimental composite resins. A mixture of 30 mol% Bis-GMA and 70 mol% TEGDMA was prepared as a base monomer and to which a photoinitiator (camphorquinone) and a co-initiator (N,N-dimethylaminoethyl methacrylate) were added. Four different irregular- and spherical-shaped filler types with an average particle size of 1.9-11.1 microm were added to the mixture in three different filler contents of 20, 30, and 40 vol%. Light transmittance characteristics including light diffusion characteristics of the materials were evaluated. Color values and color differences among filler contents of the materials were also determined. Materials containing smaller and irregular-shaped fillers showed higher light transmittance and diffusion angle distribution with a sharper peak, as compared with those containing larger and spherical-shape fillers. It was also found that there was a significant correlation between the specific surface area of fillers and the color difference of the materials containing the fillers. Our results indicated that the shape of filler particles, as well as particle size and filler content, significantly affected the light transmittance characteristics--including light diffusion characteristics--and color of composite resins.

Nanosized Selenium: A Novel Platform Technology to Prevent Bacterial Infections

NASA Astrophysics Data System (ADS)

Wang, Qi

As an important category of bacterial infections, healthcare-associated infections (HAIs) are considered an increasing threat to the safety and health of patients worldwide. HAIs lead to extended hospital stays, contribute to increased medical costs, and are a significant cause of morbidity and mortality. In the United States, infections encountered in the hospital or a health care facility affect more than 1.7 million patients, cost 35.7 billion to 45 billion, and contribute to 88,000 deaths in hospitals annually. The most conventional and widely accepted method to fight against bacterial infections is using antibiotics. However, because of the widespread and sometimes inappropriate use of antibiotics, many strains of bacteria have rapidly developed antibiotic resistance. Those new, stronger bacteria pose serious, worldwide threats to public health and welfare. In 2014, the World Health Organization (WHO) reported antibiotic resistance as a global serious threat that is no longer a prediction for the future but is now reality. It has the potential to affect anyone, of any age, in any country. The most effective strategy to prevent antibiotic resistance is minimizing the use of antibiotics. In recent years, nanomaterials have been investigated as one of the potential substitutes of antibiotics. As a result of their vastly increased ratio of surface area to volume, nanomaterials will likely exert a stronger interaction with bacteria which may affect bacterial growth and propagation. A major concern of most existing antibacterial nanomaterials, like silver nanoparticles, is their potential toxicity. But selenium is a non-metallic material and a required nutrition for the human body, which is recommended by the FDA at a 53 to 60 μg daily intake. Nanosized selenium is considered to be healthier and less toxic compared with many metal-based nanomaterials due to the generation of reactive oxygen species from metals, especially heavy metals. Therefore, the objectives of this dissertation were to synthesize selenium nanoparticles, characterize nanosized selenium coatings on various materials, test the effectiveness of selenium coated materials at inhibiting bacteria growth and biofilm formation and investigate the mechanisms of how selenium nanoparticles inhibit bacteria growth. The nanosized selenium coated materials showed significant and continuous inhibitions to bacteria growth by up to 92.5% without using any antibiotics. The work performed in this dissertation presents a novel platform technology based on nanosized selenium to inhibit bacterial infections on various materials, which demonstrates the strong potential applications of nanosized selenium as an antibacterial agent in hospital environments and healthcare settings.

Li- and Mn-Rich Cathode Materials: Challenges to Commercialization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zheng, Jianming; Myeong, Seungjun; Cho, Woongrae

2016-12-14

The lithium- and manganese-rich (LMR) layered structure cathode exhibit one of the highest specific energy (~900 Wh kg-1) among all the cathode materials. However, the practical applications of LMR cathodes are still hindered by several significant challenges including voltage fade, large initial capacity loss, poor rate capability and limited cycle life. Herein, we review the recent progresses and understandings on the application of LMR cathode materials from practical point of view. Several key parameters of LMR cathodes that affect the LMR/graphite full cell operation are systematically analysed. These factors include the first cycle capacity loss, voltage fade, powder tap density,more » electrode density of LMR based cathode etc. New approaches to minimize the detrimental effect of these factors are highlighted in this work. We also provided the perspectives for the future research on LMR cathode materials, focusing on addressing the fundamental problems of LMR cathodes while always keeping practical considerations in mind.« less

[Influence of autoclave sterilization on dimensional stability and detail reproduction of 5 additional silicone impression materials].

PubMed

Xu, Tong-kai; Sun, Zhi-hui; Jiang, Yong

2012-03-01

To evaluate the dimensional stability and detail reproduction of five additional silicone impression materials after autoclave sterilization. Impressions were made on the ISO 4823 standard mold containing several marking lines, in five kinds of additional silicone. All the impressions were sterilized by high temperature and pressure (135 °C, 212.8 kPa) for 25 min. Linear measurements of pre-sterilization and post-sterilization were made with a measuring microscope. Statistical analysis utilized single-factor analysis with pair-wise comparison of mean values when appropriate. Hypothesis testing was conducted at alpha = 0.05. No significant difference was found between the pre-sterilization and post-sterilization conditions for all locations, and all the absolute valuse of linear rate of change less than 8%. All the sterilization by the autoclave did not affect the surfuce detail reproduction of the 5 impression materials. The dimensional stability and detail reproduction of the five additional silicone impression materials in the study was unaffected by autoclave sterilization.

Structural, textural and morphological characteristics of tannins from Acacia mearnsii encapsulated using sol-gel methods: Applications as antimicrobial agents.

PubMed

Dos Santos, Cristiane; Vargas, Álvaro; Fronza, Ney; Dos Santos, João Henrique Zimnoch

2017-03-01

Tannins from Acacia mearnsii were encapsulated using four different sol-gel methods acid (SGAR), basic (SGBR), silicate (SGSR) and non-hydrolytic (SGNHR) routes. The hybrid materials were analyzed using a set of techniques to characterize their structure, texture and morphology. The antimicrobial performance of the encapsulated materials was evaluated against different microorganisms (Staphylococcus aureus, Escherichia coli, Aspergillus niger and Candida sp.). The data showed that the encapsulation route significantly affects the characteristics of the resulting hybrid materials. Better functional performances were obtained using the silicate route, which produced mesoporous materials with a small surface area (0.96m 2 g -1 ) and small particle size (<1nm). These characteristics promoted the gradual release of tannins in an aqueous medium and improved their interactions with microorganisms. Furthermore, the process demonstrated the preservation of tannins after synthesis and increased antimicrobial activity (via a controlled tannin release), as demonstrated by the moderate activity against filamentous fungi and yeast. Copyright © 2016. Published by Elsevier B.V.

Diverse Electron-Induced Optical Emissions from Space Observatory Materials at Low Temperatures

NASA Technical Reports Server (NTRS)

Dennison, J.R.; Jensen, Amberly Evans; Wilson, Gregory; Dekany, Justin; Bowers, Charles W.; Meloy, Robert

2013-01-01

Electron irradiation experiments have investigated the diverse electron-induced optical and electrical signatures observed in ground-based tests of various space observatory materials at low temperature. Three types of light emission were observed: (i); long-duration cathodoluminescence which persisted as long as the electron beam was on (ii) short-duration (<1 s) arcing, resulting from electrostatic discharge; and (iii) intermediate-duration (100 s) glow-termed "flares". We discuss how the electron currents and arcing-as well as light emission absolute intensity and frequency-depend on electron beam energy, power, and flux and the temperature and thickness of different bulk (polyimides, epoxy resins, and silica glasses) and composite dielectric materials (disordered SiO2 thin films, carbon- and fiberglass-epoxy composites, and macroscopically-conductive carbon-loaded polyimides). We conclude that electron-induced optical emissions resulting from interactions between observatory materials and the space environment electron flux can, in specific circumstances, make significant contributions to the stray light background that could possibly adversely affect the performance of space-based observatories.

Reactive transport simulations of alternative flow pathways in the ambient unsaturated zone at Yucca Mountain, Nevada

NASA Astrophysics Data System (ADS)

Browning, L.; Murphy, W.; Manepally, C.; Fedors, R.

2003-04-01

Uncertainties in simulated ambient system unsaturated zone flow could have a significant impact on performance evaluations of the proposed nuclear waste repository at Yucca Mountain, Nevada. In addition to determining variations in the quantity of water available to corrode engineered materials and transport radionuclides, model assumptions regarding flow pathways may significantly affect estimates of groundwater chemistry. The manner and extent to which groundwater compositions evolve along a flow pathway are determined mainly by thermohydrologic conditions, the types of reactive materials encountered, and the interaction times with those materials. Simulated groundwater compositions can thus vary significantly depending on whether or not the flow model includes lateral diversion of infiltrating waters, or preferential flow pathways in variably-saturated materials. To assist a regulatory review of a potential license application for a geologic repository for high-level waste, we developed a reactive transport model for the ambient hydrogeochemical system at Yucca Mountain. The model simulates two phase, nonisothermal, advective and diffusive flow and transport through a one dimensional, matrix and fracture continua (dual permeability) containing ten kinetically reactive hydrostatigraphic layers in the vicinity of the SD-9 borehole at Yucca Mountain. In this presentation, we describe how the model was used to evaluate alternative ambient unsaturated zone flow pathways proposed by the U.S. Department of Energy. This abstract is an independent product of the CNWRA and does not necessarily reflect the views or regulatory position of the NRC.

Cultivation of algal biofilm using different lignocellulosic materials as carriers.

PubMed

Zhang, Qi; Liu, Cuixia; Li, Yubiao; Yu, Zhigang; Chen, Zhihua; Ye, Ting; Wang, Xun; Hu, Zhiquan; Liu, Shiming; Xiao, Bo; Jin, Shiping

2017-01-01

Algal biofilm technology is recently supposed to be a promising method to produce algal biomass as the feedstock for the production of biofuels. However, the carrier materials currently used to form algal biofilm are either difficult to be obtained at a low price or undurable. Commercialization of the biofilm technology for algal biomass production extremely requires new and inexpensive materials as biofilm carriers with high biomass production performances. Four types of lignocellulosic materials were investigated to evaluate their performance of acting as carriers for algal cells attachment and the relevant effects on the algal biomass production in this study. The cultivation of algal biofilm was processed in a self-designed flat plate photo-bioreactor. The biofilm production and chemical composition of the harvested biomass were determined. The surface physics properties of the materials were examined through a confocal laser-scanning microscopy. Algal biomass production varied significantly with the variation of the carriers ( P  < 0.05). All the lignocellulosic materials showed better performances in biofilm production than poly methyl methacrylate, and the application of pine sawdust as the carrier could gain the maximum biofilm productivity of 10.92 g m -2  day -1 after 16-day cultivation. In addition, 20.10-23.20% total lipid, 30.35-36.73% crude proteins, and 20.29-25.93% carbohydrate were achieved from the harvested biomasses. Biomass productivity increased linearly as the increase of surface roughness, and Wenzel's roughness factor of the tested materials, and surface roughness might significantly affect the biomass production through the size of surface morphology and the area of surface ( P  < 0.05). The results showed that lignocellulosic materials can be efficient carriers for low-cost cultivation of algal biofilm and the enhancement of biomass productivity.

The longitudinal effects of neighbourhood social and material deprivation change on psychological distress in urban, community-dwelling Canadian adults.

PubMed

Blair, A; Gariépy, G; Schmitz, N

2015-07-01

The purpose of this study was to assess how longitudinal changes in neighbourhood material and social deprivation affect distress outcomes in adult Canadians. This study used a prospective cohort approach. We paired data from 2745 urban participants of Canada's National Population Health Survey-who completed the Kessler 6-Item psychological distress screening tool at baseline and follow-up-with neighbourhood social and material deprivation data from the census-based Pampalon Deprivation Index. Data were paired using participants' postal code. We conducted multiple linear regression models, which were stratified by baseline deprivation level and controlled for key confounders. Most participants lived in neighbourhoods that did not change drastically in social or material deprivation level during the six years between baseline and follow-up. We found that a worsening of material settings was significantly associated with worsening distress scores at follow-up. This finding is discussed in the context of existing literature, and made relevant for urban health research and policy. Copyright © 2015 The Royal Society for Public Health. Published by Elsevier Ltd. All rights reserved.

Meso-scopic Densification in Brittle Granular Materials

NASA Astrophysics Data System (ADS)

Neal, William; Appleby-Thomas, Gareth; Collins, Gareth

2013-06-01

Particulate materials are ideally suited to shock absorbing applications due to the large amounts of energy required to deform their inherently complex meso-structure. Significant effort is being made to improve macro-scale material models to represent these atypical materials. On the long road towards achieving this capability, an important milestone would be to understand how particle densification mechanisms are affected by loading rate. In brittle particulate materials, the majority of densification is caused by particle fracture. Macro-scale quasi-static and dynamic compaction curves have been measured that show good qualitative agreement. There are, however, some differences that appear to be dependent on the loading rate that require further investigation. This study aims to investigate the difference in grain-fracture behavior between the quasi-static and shock loading response of brittle glass microsphere beds using a combination of quasi-static and dynamic loading techniques. Results from pressure-density measurements, sample recovery, and meso-scale hydrocode models (iSALE, an in-house simulation package) are discussed to explain the differences in particle densification mechanisms between the two loading rate regimes. Gratefully funded by AWE.plc.

3D bioactive composite scaffolds for bone tissue engineering.

PubMed

Turnbull, Gareth; Clarke, Jon; Picard, Frédéric; Riches, Philip; Jia, Luanluan; Han, Fengxuan; Li, Bin; Shu, Wenmiao

2018-09-01

Bone is the second most commonly transplanted tissue worldwide, with over four million operations using bone grafts or bone substitute materials annually to treat bone defects. However, significant limitations affect current treatment options and clinical demand for bone grafts continues to rise due to conditions such as trauma, cancer, infection and arthritis. Developing bioactive three-dimensional (3D) scaffolds to support bone regeneration has therefore become a key area of focus within bone tissue engineering (BTE). A variety of materials and manufacturing methods including 3D printing have been used to create novel alternatives to traditional bone grafts. However, individual groups of materials including polymers, ceramics and hydrogels have been unable to fully replicate the properties of bone when used alone. Favourable material properties can be combined and bioactivity improved when groups of materials are used together in composite 3D scaffolds. This review will therefore consider the ideal properties of bioactive composite 3D scaffolds and examine recent use of polymers, hydrogels, metals, ceramics and bio-glasses in BTE. Scaffold fabrication methodology, mechanical performance, biocompatibility, bioactivity, and potential clinical translations will be discussed.

Evaluation of a Variable-Impedance Ceramic Matrix Composite Acoustic Liner

NASA Technical Reports Server (NTRS)

Jones, M. G.; Watson, W. R.; Nark, D. M.; Howerton, B. M.

2014-01-01

As a result of significant progress in the reduction of fan and jet noise, there is growing concern regarding core noise. One method for achieving core noise reduction is via the use of acoustic liners. However, these liners must be constructed with materials suitable for high temperature environments and should be designed for optimum absorption of the broadband core noise spectrum. This paper presents results of tests conducted in the NASA Langley Liner Technology Facility to evaluate a variable-impedance ceramic matrix composite acoustic liner that offers the potential to achieve each of these goals. One concern is the porosity of the ceramic matrix composite material, and whether this might affect the predictability of liners constructed with this material. Comparisons between two variable-depth liners, one constructed with ceramic matrix composite material and the other constructed via stereolithography, are used to demonstrate this material porosity is not a concern. Also, some interesting observations are noted regarding the orientation of variable-depth liners. Finally, two propagation codes are validated via comparisons of predicted and measured acoustic pressure profiles for a variable-depth liner.

Quality and seasonal variation of rainwater harvested from concrete, asphalt, ceramic tile and green roofs in Chongqing, China.

PubMed

Zhang, Qianqian; Wang, Xiaoke; Hou, Peiqiang; Wan, Wuxing; Li, Ruida; Ren, Yufen; Ouyang, Zhiyun

2014-01-01

There is an urgent requirement to examine the quality of harvested rainwater for potable and non-potable purposes, based on the type of roofing material. In this study, we examined the effect on the quality of harvested rainwater of conventional roofing materials (concrete, asphalt and ceramic tile roofs) compared with alternative roofing materials (green roof). The results showed that the ceramic tile roof was the most suitable for rainwater-harvesting applications because of the lower concentrations of leachable pollutants. However, in this study, the green roof was not suitable for rainwater harvesting applications. In addition, seasonal trends in water quality parameters showed that pollutants in roof runoff in summer and autumn were lower than those in winter and spring. This study revealed that the quality of harvested rainwater was significantly affected by the roofing material; therefore, local government and urban planners should develop stricter testing programs and produce more weathering resistant roofing materials to allow the harvesting of rainwater for domestic and public uses. Copyright © 2013 Elsevier Ltd. All rights reserved.

Multiple points of equilibrium for active magnetic regenerators using first order magnetocaloric material

NASA Astrophysics Data System (ADS)

Niknia, I.; Trevizoli, P. V.; Govindappa, P.; Christiaanse, T. V.; Teyber, R.; Rowe, A.

2018-05-01

First order transition material (FOM) usually exhibits magnetocaloric effects in a narrow temperature range which complicates their use in an active magnetic regenerator (AMR) refrigerator. In addition, the magnetocaloric effect in first order materials can vary with field and temperature history of the material. This study examines the behavior of a MnFe(P,Si) FOM sample in an AMR cycle using a numerical model and experimental measurements. For certain operating conditions, multiple points of equilibrium (MPE) exist for a fixed hot rejection temperature. Stable and unstable points of equilibriums (PEs) are identified and the impacts of heat loads, operating conditions, and configuration losses on the number of PEs are discussed. It is shown that the existence of multiple PEs can affect the performance of an AMR significantly for certain operating conditions. In addition, the points where MPEs exist appear to be linked to the device itself, not just the material, suggesting the need to layer a regenerator in a way that avoids MPE conditions and to layer with a specific device in mind.

Preparation of laminin/nidogen adsorbed urinary bladder decellularized materials via a mussel-inspired polydopamine coating for pelvic reconstruction

PubMed Central

Ge, Liangpeng; Cao, Chuan; Chen, Shixuan; Shao, Bin; Li, Qianyong; Li, Qingtao; Liu, Lubin; Liang, Zhiqing; Huang, Yong

2017-01-01

Pelvic organ prolapse (POP) is a serious health issue that affects many adult women. A common strategy for POP reconstruction is to use scaffold materials to reconstruct the prolapsed pelvic organ. However, the existing materials for pelvic reconstruction do not meet the clinical requirements for biocompatibility, mechanics and immunological rejection. To address these concerns, urinary bladder decellularized materials (UBDM) was selected due to their good strain-stress resistance. To enhance its biocompatibility, laminin/nidogen was used to modify the UBDM with a mussel-inspired polydopamine coating. We found that the biocompatibility and mechanical properties of laminin/nidogen-Dopamine-UBDM were significantly enhanced and that the degradation rate of laminin/nidogen-Dopamine-UBDM was markedly reduced. Moreover, the expression of CD31 in the laminin/nidogen-Dopamine-UBDM group was higher than that in the normal UBDM group. The laminin/nidogen-Dopamine-UBDM treatment mainly guided M2 type macrophages and led to an inflammatory response. These results indicate that laminin/nidogen adsorbed urinary bladder decellularized materials are promising for use in pelvic reconstruction. PMID:29312483

Relative toxicity of products of pyrolysis and combustion of polymeric materials using various test conditions

NASA Technical Reports Server (NTRS)

Hilado, C. J.

1976-01-01

Relative toxicity data for a large number of natural and synthetic polymeric materials are presented which were obtained by 11 pyrolysis and three flaming-combustion test methods. The materials tested include flexible and rigid polyurethane foams, different kinds of fabrics and woods, and a variety of commodity polymers such as polyethylene. Animal exposure chambers of different volumes containing mice, rats, or rabbits were used in the tests, which were performed over the temperature range from ambient to 800 C with and without air flow or recirculation. The test results are found to be sensitive to such variables as exposure mode, temperature, air flow and dilution, material concentration, and animal species, but relative toxicity rankings appear to be similar for many methods and materials. It is concluded that times to incapacitance and to death provide a more suitable basis for relative toxicity rankings than percent mortality alone, that temperature is the most important variable in the tests reported, and that variables such as chamber volume and animal species may not significantly affect the rankings.

Sorption and Diffusion of Water Vapor and Carbon Dioxide in Sulfonated Polyaniline as Chemical Sensing Materials

PubMed Central

Liang, Qiuhua; Jiang, Junke; Ye, Huaiyu; Yang, Ning; Cai, Miao; Xiao, Jing; Chen, Xianping

2016-01-01

A hybrid quantum mechanics (QM)/molecular dynamics (MD) simulation is performed to investigate the effect of an ionizable group (–SO3−Na+) on polyaniline as gas sensing materials. Polymers considered for this work include emeraldine base of polyaniline (EB-PANI) and its derivatives (Na-SPANI (I), (II) and (III)) whose rings are partly monosubstituted by –SO3−Na+. The hybrid simulation results show that the adsorption energy, Mulliken charge and band gap of analytes (CO2 and H2O) in polyaniline are relatively sensitive to the position and the amounts of –SO3−Na+, and these parameters would affect the sensitivity of Na-SPANI/EB-PANI towards CO2. The sensitivity of Na-SPANI (III)/EB-PANI towards CO2 can be greatly improved by two orders of magnitude, which is in agreement with the experimental study. In addition, we also demonstrate that introducing –SO3−Na+ groups at the rings can notably affect the gas transport properties of polyaniline. Comparative studies indicate that the effect of ionizable group on polyaniline as gas sensing materials for the polar gas molecule (H2O) is more significant than that for the nonpolar gas molecule (CO2). These findings contribute in the functionalization-induced variations of the material properties of polyaniline for CO2 sensing and the design of new polyaniline with desired sensing properties. PMID:27128921

Acoustic properties and durability of liner materials at non-standard atmospheric conditions

NASA Technical Reports Server (NTRS)

Ahuja, K. K.; Gaeta, R. J., Jr.; Hsu, J. S.

1994-01-01

This report documents the results of an experimental study on how acoustic properties of certain absorbing liner materials are affected by nonstandard atmospheric conditions. This study was motivated by the need to assess risks associated with incorporating acoustic testing capability in wind tunnels with semicryogenic high Reynolds number aerodynamic and/or low pressure capabilities. The study consisted of three phases: 1) measurement of acoustic properties of selected liner materials at subatmospheric pressure conditions, 2) periodic cold soak and high pressure exposure of liner materials for 250 cycles, and 3) determination of the effect of periodic cold soak on the acoustic properties of the liner materials at subatmospheric conditions and the effect on mechanical resiliency. The selected liner materials were Pyrell foam, Fiberglass, and Kevlar. A vacuum facility was used to create the subatmospheric environment in which an impedance tube was placed to measure acoustic properties of the test materials. An automated cryogenic cooling system was used to simulate periodic cold soak and high pressure exposure. It was found that lower ambient pressure reduced the absorption effectiveness of the liner materials to varying degrees. Also no significant change in the acoustic properties occurred after the periodic cold soak. Furthermore, mechanical resiliency tests indicated no noticeable change.

The effect of shredding and test apparatus size on compressibility and strength parameters of degraded municipal solid waste.

PubMed

Hossain, M S; Gabr, M A; Asce, F

2009-09-01

In many situations, MSW components are processed and shredded before use in laboratory experiments using conventional soil testing apparatus. However, shredding MSW material may affect the target property to be measured. The objective of this study is to contribute to the understanding of the effect of shredding of MSW on the measured compressibility and strength properties. It is hypothesized that measured properties can be correlated to an R-value, the ratio of waste particle size to apparatus size. Results from oedometer tests, conducted on 63.5 mm, 100 mm, 200 mm diameter apparatus, indicated the dependency of the compressibility parameters on R-value. The compressibility parameters are similar for the same R-value even though the apparatus size varies. The results using same apparatus size with variable R-values indicated that shredding of MSW mainly affects initial compression. Creep and biological strain rate of the tested MSW are not significantly affected by R-value. The shear strength is affected by shredding as the light-weight reinforcing materials are shredded into smaller pieces during specimen preparation. For example, the measured friction angles are 32 degrees and 27 degrees for maximum particle sizes of 50 mm and 25 mm, respectively. The larger MSW components in the specimen provide better reinforcing contribution. This conclusion is however dependent on comparing specimen at the same level of degradation since shear strength is also a function of extent of degradation.

Rate of contrast material extravasations and allergic-like reactions: effect of extrinsic warming of low-osmolality iodinated CT contrast material to 37 degrees C.

PubMed

Davenport, Matthew S; Wang, Carolyn L; Bashir, Mustafa R; Neville, Amy M; Paulson, Erik K

2012-02-01

To retrospectively determine whether extrinsic warming of the low-osmolality contrast material iopamidol to 37°C prior to intravenous administration at computed tomography (CT) affects extravasation and allergic-like reaction rates. The need to obtain informed patient consent was waived for this HIPAA-compliant and institutional review board-approved analysis. All adverse events related to the intravenous administration of iopamidol during CT examinations occurring 200 days before (period 1) and 200 days after (period 2) the cessation of extrinsic contrast material warming (37°C) for intravenous injections of less than 6 mL/sec at Duke University Medical Center (Durham, NC) were retrospectively reviewed. Adverse event rates were compared by using χ2 statistics. There were 12,682 injections during period 1 (10,831 injections of iopamidol 300 and 1851 injections of iopamidol 370) and 12,138 injections (10, 064 injections of iopamidol 300 and 2074 injections of iopamidol 370) during period 2. Adverse event rates for iopamidol 300 were not affected by extrinsic warming (extravasation rates: 0.30% [32 of 10,831] in period 1 vs 0.23% [23 of 10,064] in period 2, P=.64; allergic-like reaction rates: 0.39% [42 of 10,831] in period 1 vs 0.46% [46 of 10,064] in period 2, P=.74; overall adverse events: 0.68% [74 of 10,831] in period 1 vs 0.69% [69 of 10,064] in period 2, P=.99). Discontinuation of extrinsic warming was associated with significantly increased extravasation and overall adverse event rates for iopamidol 370 (extravasation rates: 0.27% [five of 1851] vs 0.87% [18 of 2074], P=.05; allergic-like reaction rates: 0.16% [three of 1851] vs 0.39% [eight of 2074], P=.42; overall adverse events: 0.43% [eight of 1851] vs 1.25% [26 of 2074], P=.02). Extrinsic warming (to 37°C) does not appear to affect adverse event rates for intravenous injections of iopamidol 300 of less than 6 mL/sec but is associated with a significant reduction in extravasation and overall adverse event rates for the more viscous iopamidol 370. © RSNA, 2011

Parental genetic material and oxygen concentration affect hatch dynamics of mouse embryo in vitro.

PubMed

Zhan, Shaoquan; Cao, Shanbo; Du, Hongzi; Sun, Yuan; Li, Li; Ding, Chenhui; Zheng, Haiyan; Huang, Junjiu

2018-04-21

Hatching is crucial for mammalian embryo implantation, since difficulties during this process can lead to implantation failure, ectopic pregnancy and consequent infertility. Despite years of intensive researches, how internal and external factors affecting embryo hatch are still largely unclear. The effects of parental genetic material and oxygen concentration on hatch process were examined. Fertilized and parthenogenetic mouse preimplantation embryos were cultured in vitro under 5 and 20% oxygen for 120 h. Zona pellucida drilling by Peizo micromanipulation were performed to resemble the breach by sperm penetration. Firstly, parthenogenetic embryos had similarly high blastocyst developmental efficiency as fertilized embryos, but significantly higher hatch ratio than fertilized embryos in both O 2 concentrations. 5% O 2 reduced the hatch rate of fertilized embryos from 58.2 to 23.8%, but increased that of parthenogenetic embryos from 81.2 to 90.8% significantly. Analogously, 5% O 2 decreased the ratio of Oct4-positive cells in fertilized blastocysts, whereas increased that in parthenogenetic blastocysts. Additionally, 5% O 2 increased the total embryonic cell number in both fertilized and parthegenetic embryos, when compared to 20% O 2 , and the total cell number of fertilized embryos was also higher than that of parthegenetic embryos, despite O 2 concentration. Real-time PCR revealed that the expression of key genes involving in MAPK pathway and superoxide dismutase family might contribute to preimplantation development and consequent blastocyst hatch in vitro. Finally, we showed that fertilized and parthenogenetic embryos have diverse hatch dynamics in vitro, although the zona pellucida integrity is not the main reason for their mechanistic differences. Both parental genetic material and O 2 concentration, as the representative of intrinsic and extrinsic factors respectively, have significant impacts on mouse preimplantation development and subsequent hatch dynamics, probably by regulating the gene expression involving in MAPK pathway and superoxide dismutase family to control embryonic cell proliferation and allocation of ICM cells.

Rheological properties of veneer trial pastes relevant to clinical success.

PubMed

Chadwick, R G; McCabe, J F; Carrick, T E

2008-03-22

The porcelain veneer is a relatively conservative means of improving the appearance of teeth. As these restorations are usually highly visible it is essential to gain the approval of the patient before final cementation takes place. As a result a variety of trial pastes are available that match the shades of the resins that are used ultimately to finally cement the veneer in place. Such restorations, by virtue of their small size and fragility, are difficult to handle and position. It is therefore important that the application of trial paste does not impede placement and retention upon the tooth surface at try in whilst the patient assesses its appearance. To determine the rheological properties of three makes of trial pastes (Calibra - Dentsply Caulk, USA; Nexus - Kerr, USA; Rely X - 3M Espe, USA) and assess if temperature affected these. Design In vitro rheological measurement. For each product the rheological properties of three shades were determined at both 25 degrees C and 35 degrees C three times. Measurements of both the Initial Yield Stress and Shear Rate Index were undertaken using a controlled stress rheometer (Carri-med, Dorking, UK) in flow mode with a cone-and-plate test configuration. One way analyses of variance of the initial yield and shear rate index for each shade of material at 25 and 35 degrees C demonstrated no significant effects of temperature with the exception of the initial yield of Nexus (P = 0.0024) where the yield stress of the white shade was significantly (P <0.01) higher at 35 degrees C than at 25 degrees C. In all cases the yield stress for Nexus was of the order of ten times higher than the other materials. All materials demonstrated pseudoplastic behaviour. The variation in yield stress displayed by the materials will affect the handling of veneers and offers a potentially useful choice parameter to the clinician as to which paste bests suits their requirements.

Effectiveness of adaptive pretend play on affective expression and imagination of children with cerebral palsy.

PubMed

Hsieh, Hsieh-Chun

2012-01-01

Children with cerebral palsy (CP) have difficulty participating in role-pretending activities. The concept of adaptive play makes play accessible by modifying play materials for different needs or treatment goals for children with CP. This study examines the affective expressions and imagination in children with CP as a function of ordinary versus adaptive pretend play. The Affect in Play Scale-Brief Rating measured the affective expression and imagination for 29 children with CP and 29 typically developing children (mean age=7.34 years). Two groups of children were observed while playing with a standard set of ordinary toys for ten times and with a standard procedure of adaptive pretend play for ten times. The results show significantly different affective expressions and imagination between the two groups. Typically developing children displayed much more affective expression and imagination. However, a more positive influence of affective expression and imagination occurred in children with CP than in typically developing children. In repeated measures analysis, the frequency of positive affective expression and imagination of children with CP was higher when pretending with adaptive toys. Adaptive pretend play can promote more role-pretending behaviors and a sense of environmental control during the manipulating process for children with CP. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effect of curing modes of dual-curing core systems on microtensile bond strength to dentin and formation of an acid-base resistant zone.

PubMed

Li, Na; Takagaki, Tomohiro; Sadr, Alireza; Waidyasekera, Kanchana; Ikeda, Masaomi; Chen, Jihua; Nikaido, Toru; Tagami, Junji

2011-12-01

To evaluate the microtensile bond strength (μTBS) and acid-base resistant zone (ABRZ) of two dualcuring core systems to dentin using four curing modes. Sixty-four caries-free human molars were randomly divided into two groups according to two dual-curing resin core systems: (1) Clearfil DC Core Automix; (2) Estelite Core Quick. For each core system, four different curing modes were applied to the adhesive and core resin: (1) dual-cured and dual-cured (DD); (2) chemically cured and dual-cured (CD); (3) dual-cured and chemically cured (DC); (4) chemically cured and chemically cured (CC). The specimens were sectioned into sticks (n = 20 for each group) for the microtensile bond test. μTBS data were analyzed using two-way ANOVA and the Dunnett T3 test. Failure patterns were examined with scanning electron microscopy (SEM) to determine the proportion of each mode. Dentin sandwiches were produced and subjected to an acid-base challenge. After argon-ion etching, the ultrastructure of ABRZ was observed using SEM. For Clearfil DC Core Automix, the μTBS values in MPa were as follows: DD: 29.1 ± 5.4, CD: 21.6 ± 5.6, DC: 17.9 ± 2.8, CC: 11.5 ± 3.2. For Estelite Core Quick, they were: DD: 48.9 ±5.7, CD: 20.5 ± 4.7, DC: 41.4 ± 8.3, CC: 19.1 ± 6.0. The bond strength was affected by both material and curing mode, and the interaction of the two factors was significant (p < 0.001). Within both systems, there were significant differences among groups, and the DD group showed the highest μTBS (p < 0.05). ABRZ morphology was not affected by curing mode, but it was highly adhesive-material dependent. The curing mode of dual-curing core systems affects bond strength to dentin, but has no significant effect on the formation of ABRZ.

Residual methyl methacrylate monomer, water sorption, and water solubility of hypoallergenic denture base materials.

PubMed

Pfeiffer, Peter; Rosenbauer, Ernst-Ulrich

2004-07-01

Denture base materials have the potential to cause irritation and allergic reaction to the oral mucosa. Water sorption and water solubility of denture base resins affect dimensional behavior and denture stability. A correlation between residual monomer and water sorption exists. This in vitro study compared the amount of residual monomer, quantity of water sorption, and solubility of 4 denture base materials purported to be hypoallergenic with those of a polymethyl methacrylate-based (PMMA) heat-polymerizing acrylic resin. The denture base resins Sinomer (heat-polymerized, modified methacrylate), Polyan (thermoplastic, modified methacrylate), Promysan (thermoplastic, enterephthalate-based), and Microbase (microwave polymerized, polyurethane-based), which are purported to be hypoallergenic, and Paladon 65 (heat-polymerized, methacrylate, control group) were examined. Specimens of each material were tested for residual methyl methacrylate (MMA) monomer (% wt, n=3), amount of water sorption (microg/mm3, n=5) and water solubility (microg/mm3, n=5), according to ISO 1567:2000. The residual MMA monomer concentrations were determined by gas chromatography (GC). The data were analyzed with 1-way ANOVA and the Bonferroni-Dunn multiple comparisons post hoc analysis for each test variable (alpha=.05). Significantly lower residual MMA monomer was shown for Sinomer and Polyan compared to the PMMA control group (0.90 +/- 0.20% wt, P<.05). Sinomer contained 0.31% +/- 0.00% wt MMA monomer, and Polyan exhibited residual MMA monomer content of 0.44% +/- 0.01% wt. Promysan and Microbase did not contain detectable residual MMA. Water sorption of Promysan (16.21 +/- 0.96 microg/mm3) was significantly lower than Paladon 65 (23.04 +/- 3.13 microg/mm3, P<.0001), whereas water solubility of the hypoallergenic denture base materials (0.34-0.84 +/- 0.05-0.09 microg/mm3) was not significantly lower than the PMMA material (0.40 +/- 0.06 microg/mm3, P>.05). Except for Sinomer, the tested denture base resins passed the requirements of ISO 1567 regarding residual MMA monomer (<2.2% wt). Sinomer failed to comply with the requirements for residual MMA monomer because the manufacturer claimed that the material did not contain any MMA. The tested denture base materials fulfilled the requirements regarding water sorption (<32 microg/mm3) and solubility (<1.6 microg/mm3). The tested hypoallergenic denture base materials exhibited significantly lower residual monomer content than PMMA. Promysan and Microbase showed no detectable residual MMA.

Interplay of screening and superconductivity in low-dimensional materials

NASA Astrophysics Data System (ADS)

Schönhoff, G.; Rösner, M.; Groenewald, R. E.; Haas, S.; Wehling, T. O.

2016-10-01

A quantitative description of Coulomb interactions is developed for two-dimensional superconducting materials, enabling us to compare intrinsic with external screening effects, such as those due to substrates. Using the example of a doped monolayer of MoS2 embedded in a tunable dielectric environment, we demonstrate that the influence of external screening is limited to a length scale, bounded from below by the effective thickness of the quasi-two-dimensional material and from above by its intrinsic screening length. As a consequence, it is found that unconventional Coulomb-driven superconductivity cannot be induced in MoS2 by tuning the substrate properties alone. Our calculations of the retarded Morel-Anderson Coulomb potential μ* reveal that the Coulomb interactions, renormalized by the reduced layer thickness and the substrate properties, can shift the onset of the electron-phonon driven superconducting phase in monolayer MoS2 but do not significantly affect the critical temperature at optimal doping.

Effect of Chemical Treatments on Flax Fibre Reinforced Polypropylene Composites on Tensile and Dome Forming Behaviour

PubMed Central

Wang, Wentian; Lowe, Adrian; Kalyanasundaram, Shankar

2015-01-01

Tensile tests were performed on two different natural fibre composites (same constituent material, similar fibre fraction and thickness but different weave structure) to determine changes in mechanical properties caused by various aqueous chemical treatments and whether any permanent changes remain on drying. Scanning electronic microscopic examinations suggested that flax fibres and the flax/polypropylene interface were affected by the treatments resulting in tensile property variations. The ductility of natural fibre composites was improved significantly under wet condition and mechanical properties (elongation-to-failure, stiffness and strength) can almost retain back to pre-treated levels when dried from wet condition. Preheating is usually required to improve the formability of material in rapid forming, and the chemical treatments performed in this study were far more effective than preheating. The major breakthrough in improving the formability of natural fibre composites can aid in rapid forming of this class of material system. PMID:25789505

Stress intensity factors of eccentric cracks in bi-materials plate under mode I loading

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ismail, A. E.

2015-05-15

Bi-material plates were generally used to joint electronic devices or mechanical components requiring dissimilar materials to be attached. During services, mechanical failure can be occurred due to the formation of cracks at the interfacial joint or away from the centre. Generally, linear elastic fracture mechanics approach is used to characterize these cracks based on stress intensity factors (SIF). Based on the literature survey, the SIFs for the central cracks were easily available. However, the SIFs for eccentric cracks were difficult to obtain. Therefore, this paper presented the SIFs for eccentric cracks subjected to mode I tension loading. Three important parametersmore » were used such as relative crack depth, a/L, relative offset distance, b/L and elastic mismatch, E{sub 1}/E{sub 2} or α. It was found that such parameters significantly affected the characteristic of SIFs and it was depend on the location of cracks.« less

Spatial dynamics and control of a crop pathogen with mixed-mode transmission.

PubMed

McQuaid, Christopher Finn; van den Bosch, Frank; Szyniszewska, Anna; Alicai, Titus; Pariyo, Anthony; Chikoti, Patrick Chiza; Gilligan, Christopher Aidan

2017-07-01

Trade or sharing that moves infectious planting material between farms can, for vertically-transmitted plant diseases, act as a significant force for dispersal of pathogens, particularly where the extent of material movement may be greater than that of infected vectors or inoculum. The network over which trade occurs will then effect dispersal, and is important to consider when attempting to control the disease. We consider the difference that planting material exchange can make to successful control of cassava brown streak disease, an important viral disease affecting one of Africa's staple crops. We use a mathematical model of smallholders' fields to determine the effect of informal trade on both the spread of the pathogen and its control using clean-seed systems, determining aspects that could limit the damage caused by the disease. In particular, we identify the potentially detrimental effects of markets, and the benefits of a community-based approach to disease control.

Causes and Solutions for High Energy Consumption in Traditional Buildings Located in Hot Climate Regions

NASA Astrophysics Data System (ADS)

Barayan, Olfat Mohammad

A considerable amount of money for high-energy consumption is spent in traditional buildings located in hot climate regions. High-energy consumption is significantly influenced by several causes, including building materials, orientation, mass, and openings' sizes. This paper aims to identify these causes and find practical solutions to reduce the annual cost of bills. For the purpose of this study, simulation research method has been followed. A comparison between two Revit models has also been created to point out the major cause of high-energy consumption. By analysing different orientations, wall insulation, and window glazing and applying some other high performance building techniques, a conclusion was found to confirm that appropriate building materials play a vital role in affecting energy cost. Therefore, the ability to reduce the energy cost by more than 50% in traditional buildings depends on a careful balance of building materials, mass, orientation, and type of window glazing.

Design, prototyping and autonomous control of gasoline-engine variable-pitch quadcopter

NASA Astrophysics Data System (ADS)

Tao, Pang

Supercapacitors, benefited from superb energy and power characteristics, have now drawn intensive interest for their capability of meeting the above requirements. However, traditional materials for supercapacitor electrodes such as activated carbon and metal oxide/hydroxides suffer either a low energy density or poor power input/output rate. The work presented here offer a new strategy to develop novel composites based on carbon nanotubes (CNT) to utilize the synergistic effects of both carbon host and pseudocapacitive guest materials. The main focus is located on how CNT structures with different dimensions affect the device performance. The 0 D particle-like, 2D film-structured and 3D gel-assembled CNT composites have been thoroughly investigated. It is found that CNT structures with higher dimensions are significant in preventing the agglomeration of active materials and improving the electrical conductivity, leading to satisfactory electrochemical performance.

Nanoparticle-induced unusual melting and solidification behaviours of metals

PubMed Central

Ma, Chao; Chen, Lianyi; Cao, Chezheng; Li, Xiaochun

2017-01-01

Effective control of melting and solidification behaviours of materials is significant for numerous applications. It has been a long-standing challenge to increase the melted zone (MZ) depth while shrinking the heat-affected zone (HAZ) size during local melting and solidification of materials. In this paper, nanoparticle-induced unusual melting and solidification behaviours of metals are reported that effectively solve this long-time dilemma. By introduction of Al2O3 nanoparticles, the MZ depth of Ni is increased by 68%, while the corresponding HAZ size is decreased by 67% in laser melting at a pulse energy of 0.18 mJ. The addition of SiC nanoparticles shows similar results. The discovery of the unusual melting and solidification of materials that contain nanoparticles will not only have impacts on existing melting and solidification manufacturing processes, such as laser welding and additive manufacturing, but also on other applications such as pharmaceutical processing and energy storage. PMID:28098147

Effect of IN718 Recycled Powder Reuse on Properties of Parts Manufactured by Means of Selective Laser Melting

NASA Astrophysics Data System (ADS)

Ardila, L. C.; Garciandia, F.; González-Díaz, J. B.; Álvarez, P.; Echeverria, A.; Petite, M. M.; Deffley, R.; Ochoa, J.

Powder quality control is essential to obtain parts with suitable mechanical properties in Selective Laser Melting manufacturing technique. One of the most important advantages of suchtechnique is that it allows an efficient use of the material, due to the possibility to recycle and reuse un-melted powder. Nevertheless, powder material properties may change due to repeated recycling, affecting this way the mechanicalbehavior of parts. In this paper the effect of powder reuse on its quality and on the mechanical properties of the resulting melted parts is studied via self-developed recycling methodology. The material considered for investigation was IN718, a nickel superalloy widely used in industry. After recycling powder up to 14 times, no significant changes were observed in powder and test parts properties. The results obtained in this work will help to validate powder recycling methodology for its use in current industrial Selective Laser Melting manufacturing.

Listening to a patient: An exploratory experimental investigation into the effects of vocalization and therapist gender on interpreting clinical material.

PubMed

Dauphin, Barry; Halverson, Stacey; Pouliot, Sarah; Slowik, Linda

2018-01-01

Carefully listening to the patient is of paramount importance for psychoanalysis and psychoanalytic psychotherapy. The present study explored whether patient vocalization as well as the gender of the analyst play significant roles in clinical listening. Fifty-one psychoanalysts and psychoanalytic therapists were randomly assigned to listen to one of two dramatized psychoanalytic sessions. The content of the sessions was the same for both versions, but the sessions were dramatized differently. Some differences emerged between the versions, especially on ratings of reality testing, impulse control, pressured speech, patient was confusing, and awareness of imagery. Furthermore, differences emerged between male and female analysts in terms of ratings of intervention strategies and countertransference reactions to the patient material. Session version and gender affect different ratings. Implications of the findings are discussed as is the utility of using more ecologically valid material in conducting empirical research into clinical judgment.

Culture materials affect ex vivo expansion of hematopoietic progenitor cells.

PubMed

LaIuppa, J A; McAdams, T A; Papoutsakis, E T; Miller, W M

1997-09-05

Ex vivo expansion of hematopoietic cells is important for applications such as cancer treatment, gene therapy, and transfusion medicine. While cell culture systems are widely used to evaluate the biocompatibility of materials for implantation, the ability of materials to support proliferation of primary human cells in cultures for reinfusion into patients has not been addressed. We screened a variety of commercially available polymer (15 types), metal (four types), and glass substrates for their ability to support expansion of hematopoietic cells when cultured under conditions that would be encountered in a clinical setting. Cultures of peripheral blood (PB) CD34+ cells and mononuclear cells (MNC) were evaluated for expansion of total cells and colony-forming unit-granulocyte monocyte (CFU-GM; progenitors committed to the granulocyte and/or monocyte lineage). Human hematopoietic cultures in serum-free medium were found to be extremely sensitive to the substrate material. The only materials tested that supported expansion at or near the levels of polystyrene were tissue culture polystyrene, Teflon perfluoroalkoxy, Teflon fluorinated ethylene propylene, cellulose acetate, titanium, new polycarbonate, and new polymethylpentene. MNC were less sensitive to the substrate materials than the primitive CD34+ progenitors, although similar trends were seen for expansion of the two cell populations on the substrates tested. CFU-GM expansion was more sensitive to substrate materials than was total cell expansion. The detrimental effects of a number of the materials on hematopoietic cultures appear to be caused by protein adsorption and/or leaching of toxins. Factors such as cleaning, sterilization, and reuse significantly affected the performance of some materials as culture substrates. We also used PB CD34+ cell cultures to examine the biocompatibility of gas-permeable cell culture and blood storage bags and several types of tubing commonly used with biomedical equipment. While many of the culture bag materials gave satisfactory results, all of the tubing materials severely inhibited total cell and CFU-GM expansion. Taken together, our results show that many materials approved for blood contact or considered biocompatible are not suitable for use with hematopoietic cells cultured in serum-free medium. As hematopoietic cultures are scaled up for a variety of clinical applications, it will be essential to carefully examine the biocompatibility of all materials involved.

Repeated administrations of carbon nanotubes in male mice cause reversible testis damage without affecting fertility.

PubMed

Bai, Yuhong; Zhang, Yi; Zhang, Jingping; Mu, Qingxin; Zhang, Weidong; Butch, Elizabeth R; Snyder, Scott E; Yan, Bing

2010-09-01

Soluble carbon nanotubes show promise as materials for in vivo delivery and imaging applications. Several reports have described the in vivo toxicity of carbon nanotubes, but their effects on male reproduction have not been examined. Here, we show that repeated intravenous injections of water-soluble multiwalled carbon nanotubes into male mice can cause reversible testis damage without affecting fertility. Nanotubes accumulated in the testes, generated oxidative stress and decreased the thickness of the seminiferous epithelium in the testis at day 15, but the damage was repaired at 60 and 90 days. The quantity, quality and integrity of the sperm and the levels of three major sex hormones were not significantly affected throughout the 90-day period. The fertility of treated male mice was unaffected; the pregnancy rate and delivery success of female mice that mated with the treated male mice did not differ from those that mated with untreated male mice.

Repeated administrations of carbon nanotubes in male mice cause reversible testis damage without affecting fertility

NASA Astrophysics Data System (ADS)

Bai, Yuhong; Zhang, Yi; Zhang, Jingping; Mu, Qingxin; Zhang, Weidong; Butch, Elizabeth R.; Snyder, Scott E.; Yan, Bing

2010-09-01

Soluble carbon nanotubes show promise as materials for in vivo delivery and imaging applications. Several reports have described the in vivo toxicity of carbon nanotubes, but their effects on male reproduction have not been examined. Here, we show that repeated intravenous injections of water-soluble multiwalled carbon nanotubes into male mice can cause reversible testis damage without affecting fertility. Nanotubes accumulated in the testes, generated oxidative stress and decreased the thickness of the seminiferous epithelium in the testis at day 15, but the damage was repaired at 60 and 90 days. The quantity, quality and integrity of the sperm and the levels of three major sex hormones were not significantly affected throughout the 90-day period. The fertility of treated male mice was unaffected; the pregnancy rate and delivery success of female mice that mated with the treated male mice did not differ from those that mated with untreated male mice.

Laboratory Analysis of Polymer Thin Films for Planetary Balloons and Gossamer Structures

NASA Technical Reports Server (NTRS)

Sterling, Jerry; Fairbrother, Debora A.

2004-01-01

Commercially available polymer thin fdms with thickness of 15 microns or less were evaluated for potential application as the gas envelope material of balloons and other inflated vehicles. Films on this thickness scale are of interest for Earth and Mars ballooning as well as many gossamer space structures. Due to the uniqueness of these missions relative to typical uses of these materials, application-specific materials properties measurements were made. We evaluated numerous polymer chemistries, plus a few variations within one chemistry. The data show that there are often trade-offs among the different materials, such as with polyesters and polyimides having greater stiffness (modulus) but lower tear propagation resistance than polyethylene. Sections of polyethylene films can be joined by heat sealing, while adhesives and their accompanying mass penalty must be used with polyesters and polyimides. When the analysis temperature is reduced to 190 K, polyethylenes display dramatically increased stiffness and yield point, while the increase for other materials is more modest. The data also show that manufacturing processes can significantly affect film properties. To emphasize the need for application-specific properties assessment, we discuss two recent applications using these materials.

Acoustics of multiscale sorptive porous materials

NASA Astrophysics Data System (ADS)

Venegas, R.; Boutin, C.; Umnova, O.

2017-08-01

This paper investigates sound propagation in multiscale rigid-frame porous materials that support mass transfer processes, such as sorption and different types of diffusion, in addition to the usual visco-thermo-inertial interactions. The two-scale asymptotic method of homogenization for periodic media is successively used to derive the macroscopic equations describing sound propagation through the material. This allowed us to conclude that the macroscopic mass balance is significantly modified by sorption, inter-scale (micro- to/from nanopore scales) mass diffusion, and inter-scale (pore to/from micro- and nanopore scales) pressure diffusion. This modification is accounted for by the dynamic compressibility of the effective saturating fluid that presents atypical properties that lead to slower speed of sound and higher sound attenuation, particularly at low frequencies. In contrast, it is shown that the physical processes occurring at the micro-nano-scale do not affect the macroscopic fluid flow through the material. The developed theory is exemplified by introducing an analytical model for multiscale sorptive granular materials, which is experimentally validated by comparing its predictions with acoustic measurements on granular activated carbons. Furthermore, we provide empirical evidence supporting an alternative method for measuring sorption and mass diffusion properties of multiscale sorptive materials using sound waves.

The Effect of Arch Height and Material Hardness of Personalized Insole on Correction and Tissues of Flatfoot

PubMed Central

Su, Shonglun; Mo, Zhongjun; Guo, Junchao

2017-01-01

Flat foot is one of the common deformities in the youth population, seriously affecting the weight supporting and daily exercising. However, there is lacking of quantitative data relative to material selection and shape design of the personalized orthopedic insole. This study was to evaluate the biomechanical effects of material hardness and support height of personalized orthopedic insole on foot tissues, by in vivo experiment and finite element modeling. The correction of arch height increased with material hardness and support height. The peak plantar pressure increased with the material hardness, and these values by wearing insoles of 40° were apparently higher than the bare feet condition. Harder insole material results in higher stress in the joint and ligament stress than softer material. In the calcaneocuboid joint, the stress increased with the arch height of insoles. The material hardness did not apparently affect the stress in the ankle joints, but the support heights of insole did. In general, insole material and support design are positively affecting the correction of orthopedic insole, but negatively resulting in unreasonable stress on the stress in the joint and ligaments. There should be an integration of improving correction and reducing stress in foot tissues. PMID:29065655

The Madrid Affective Database for Spanish (MADS): Ratings of Dominance, Familiarity, Subjective Age of Acquisition and Sensory Experience

PubMed Central

Hinojosa, José A.; Rincón-Pérez, Irene; Romero-Ferreiro, Mª Verónica; Martínez-García, Natalia; Villalba-García, Cristina; Montoro, Pedro R.; Pozo, Miguel A.

2016-01-01

The current study presents ratings by 540 Spanish native speakers for dominance, familiarity, subjective age of acquisition (AoA), and sensory experience (SER) for the 875 Spanish words included in the Madrid Affective Database for Spanish (MADS). The norms can be downloaded as supplementary materials for this manuscript from https://figshare.com/s/8e7b445b729527262c88 These ratings may be of potential relevance to researches who are interested in characterizing the interplay between language and emotion. Additionally, with the aim of investigating how the affective features interact with the lexicosemantic properties of words, we performed correlational analyses between norms for familiarity, subjective AoA and SER, and scores for those affective variables which are currently included in the MADs. A distinct pattern of significant correlations with affective features was found for different lexicosemantic variables. These results show that familiarity, subjective AoA and SERs may have independent effects on the processing of emotional words. They also suggest that these psycholinguistic variables should be fully considered when formulating theoretical approaches to the processing of affective language. PMID:27227521

Influence of core thickness and artificial aging on the biaxial flexural strength of different all-ceramic materials: An in-vitro study.

PubMed

Dikicier, Sibel; Ayyildiz, Simel; Ozen, Julide; Sipahi, Cumhur

2017-05-31

The purpose of this study was to investigate the flexural strength of all-ceramics with varying core thicknesses submitted to aging. In-Ceram Alumina (IC), IPS e.max Press (EM) and Katana (K) (n=40), were selected. Each group contained two core groups based on the core thickness as follows: IC/0.5, IC/0.8, EM/0.5, EM/0.8, K/0.5 and K/0.8 mm in thickness (n=20 each). Ten specimens from each group were subjected to aging and all specimens were tested for strength in a testing machine either with or without being subjected aging. The mean strength of the K were higher (873.05 MPa) than that of the IC (548.28 MPa) and EM (374.32 MPa) regardless of core thickness. Strength values increased with increasing core thickness for all IC, EM and K regardless of aging. Results of this study concluded that strength was not significantly affected by aging. Different core thicknesses affected strength of the all-ceramic materials tested (p<0.05).

Structure and mechanical behavior of human hair.

PubMed

Yu, Yang; Yang, Wen; Wang, Bin; Meyers, Marc André

2017-04-01

The understanding of the mechanical behavior of hair under various conditions broadens our knowledge in biological materials science and contributes to the cosmetic industry. The hierarchical organization of hair is studied from the intermediate filament to the structural levels. The effects of strain rate, relative humidity, and temperature are evaluated. Hair exhibits a high tensile strength, 150-270MPa, which is significantly dependent on strain rate and humidity. The strain-rate sensitivity, approximately 0.06-0.1, is comparable to that of other keratinous materials and common synthetic polymers. The structures of the internal cortex and surface cuticle are affected by the large tensile extension. One distinguishing feature, the unwinding of the α-helix and the possible transformation to β-sheet structure of keratin under tension, which affects the ductility of hair, is analytically evaluated and incorporated into a constitutive equation. A good agreement with the experimental results is obtained. This model elucidates the tensile response of the α-keratin fibers. The contributions of elastic and plastic strains on reloading are evaluated and correlated to structural changes. Copyright © 2016 Elsevier B.V. All rights reserved.

Role of out-of-plane dielectric thickness in the electrostatic simulation of atomically thin lateral junctions

NASA Astrophysics Data System (ADS)

Nipane, Ankur; Zhang, Yefei; Teherani, James T.

2018-06-01

Two-dimensional materials enable novel electronic and optoelectronic devices due to their unique properties. Device modeling plays a fundamental role in developing these novel devices by providing insights into the underlying physics. In this work, we present the dramatic impact of the simulated out-of-plane dielectric thickness on the electrostatics of lateral junctions formed from atomically thin materials. We show that unlike bulk junctions, the boundary conditions on the edges of the simulation region significantly affect the electrostatics of two-dimensional (2D) lateral junctions by modifying the out-of-plane electric field. We also present an intuitive understanding of the Neumann boundary conditions imposed on the boundaries of the simulation region. The Neumann boundary conditions alter the intended simulation by generating reflections of the device across the boundaries. Finally, we derive a minimal dielectric thickness for a symmetrically doped 2D lateral p-n junction, above which the out-of-plane simulation region boundaries minimally affect the simulated electric field, electrostatic potential, and depletion width of the junction.

Evaluation of aluminum ultralight rigid wheelchairs versus other ultralight wheelchairs using ANSI/RESNA standards.

PubMed

Liu, Hsin-yi; Pearlman, Jonathan; Cooper, Rosemarie; Hong, Eun-kyoung; Wang, Hongwu; Salatin, Benjamin; Cooper, Rory A

2010-01-01

Previous studies found that select titanium ultralight rigid wheelchairs (TURWs) had fewer equivalent cycles and less value than select aluminum ultralight folding wheelchairs (AUFWs). The causes of premature failure of TURWs were not clear because the TURWs had different frame material and design than the AUFWs. We tested 12 aluminum ultralight rigid wheelchairs (AURWs) with similar frame designs and dimensions as the TURWs using the American National Standards Institute/Rehabilitation Engineering and Assistive Technology Society of North America and International Organization for Standardization wheelchair standards and hypothesized that the AURWs would be more durable than the TURWs. Across wheelchair models, no significant differences were found in the test results between the AURWs and TURWs, except in their overall length. Tire pressure, tube-wall thickness, and tube manufacturing were proposed to be the factors affecting wheelchair durability through comparison of the failure modes, frames, and components. The frame material did not directly affect the performance of AURWs and TURWs, but proper wheelchair manufacture and design based on mechanical properties are important.

Bonding and fusion of meniscus fibrocartilage using a novel chondroitin sulfate bone marrow tissue adhesive.

PubMed

Simson, Jacob A; Strehin, Iossif A; Allen, Brian W; Elisseeff, Jennifer H

2013-08-01

The weak intrinsic meniscus healing response and technical challenges associated with meniscus repair contribute to a high rate of repair failures and meniscectomies. Given this limited healing response, the development of biologically active adjuncts to meniscal repair may hold the key to improving meniscal repair success rates. This study demonstrates the development of a bone marrow (BM) adhesive that binds, stabilizes, and stimulates fusion at the interface of meniscus tissues. Hydrogels containing several chondroitin sulfate (CS) adhesive levels (30, 50, and 70 mg/mL) and BM levels (30%, 50%, and 70%) were formed to investigate the effects of these components on hydrogel mechanics, bovine meniscal fibrochondrocyte viability, proliferation, matrix production, and migration ability in vitro. The BM content positively and significantly affected fibrochondrocyte viability, proliferation, and migration, while the CS content positively and significantly affected adhesive strength (ranged from 60±17 kPa to 335±88 kPa) and matrix production. Selected material formulations were translated to a subcutaneous model of meniscal fusion using adhered bovine meniscus explants implanted in athymic rats and evaluated over a 3-month time course. Fusion of adhered meniscus occurred in only the material containing the highest BM content. The technology can serve to mechanically stabilize the tissue repair interface and stimulate tissue regeneration across the injury site.

Nitrate losses, nutrients and heavy metal accumulation from substrates assembled for urban soils reconstruction.

PubMed

Civeira, G; Lavado, R S

2008-09-01

Urban soils may suffer mild to severe degradation as a result of physical and chemical alterations. To reconstruct these soils, a new upper horizon must be created, usually through the application of organic matter, one source of which is biosolids. Different soil mixtures were evaluated with regard to loss of nitrates in percolates and the uptake and incorporation of nutrients and heavy metals into plant tissues. The experiment was conducted in trays; treatments were mixtures of biosolids and a coarse material (e.g., sand or pine wood sawdust), combined in different proportions. Randomized trays were seeded with a mix of tall fescue (Festuca arundinacea L.) and perennial ryegrass (Lolium perenne L.). Plant biomass was quantified. Nitrates in percolates were measured, as were nutrients and heavy metals in mixtures and plant tissues. Plants accumulated substantially more N, and biomass was 40% higher, in the treatments with higher levels of biosolids. The same treatments released more nitrogen and resulted in higher percolate nitrate levels. Plants had normal concentrations of all nutrients, except nitrogen, which was low. Heavy metal concentrations were not significantly different among treatments. Based on the analysis of these data, the proportion of biosolids appears to be the most important factor affecting the quality of reconstructed soil and the rate of improvement. The type of coarse material used did not significantly affect the outcome.

Intraoral corrosion of self-ligating metallic brackets and archwires and the effect on friction

NASA Astrophysics Data System (ADS)

Tima, Lori Lynn

The purpose of this study was to investigate how the frictional coefficient was affected due to intraoral use. A secondary aim of this study was to determine whether or not there was a relationship between corrosion of orthodontic alloys and friction via scanning electron microscopic qualitative analysis. Orthodontic brackets and 0.019 x 0.025 inch stainless steel archwires were collected and divided into three groups of n=10: used bracket and used wires (UBUW), used brackets and new wires (UBNW), and new brackets and new wires (NBNW). New materials were as-received from the manufacturer, and used materials were clinically used bracket and wires collected from patients following orthodontic treatment. Archwires were pulled through bracket slots at a rate of 0.5mm/min while friction forces were measured. Following a cleaning process, the surface topography of the bracket slots was examined under a scanning electron microscope (SEM). Based on a 1-factor MANOVA, there was no significant group effect (all p>0.05) on frictional forces. Partial eta squared values indicated that intraoral exposure had only a small effect on frictional forces (≤ 3%). Qualitative analysis of SEM images did not show an association between surface characteristics of the bracket slots and magnitude of frictional force. Results suggest that surface corrosion from intraoral use does not significantly affect friction at the bracket wire interface.

From the "metaphysics of the individual" to the critique of society: on the practical significance of Michel Henry's phenomenology of life.

PubMed

Staudigl, Michael

This essay explores the practical significance of Michel Henry's "material phenomenology." Commencing with an exposition of his most basic philosophical intuition, i.e., his insight that transcendental affectivity is the primordial mode of revelation of our selfhood, the essay then brings to light how this intuition also establishes our relation to both the world and others. Animated by a radical form of the phenomenological reduction, Henry's material phenomenology brackets the exterior world in a bid to reach the concrete interior transcendental experience at the base of all exteriority. The essay argues that this "counter reduction," designed as a practical orientation to the world, suspends all traditional parameters of onto(theo)logical individuation in order to rethink subjectivity in terms of its transcendental corporeality, i.e., in terms of the invisible display of "affective flesh." The development of this "metaphysics of the individual" anchors his "practical philosophy" as he developed it-under shifting accents-throughout his oeuvre. In particular, the essay brings into focus Henry's reflections on modernity, the industry of mass culture and their "barbaric" movements. The essay briefly puts these cultural and political areas of Henry's of thinking into contact with his late "theological turn," i.e., his Christological account of Life and the (inter)subjective self-realization to which it gives rise.

A molecular dynamics study of thermal transport in nanoparticle doped Argon like solid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shahadat, Muhammad Rubayat Bin, E-mail: rubayat37@gmail.com; Ahmed, Shafkat; Morshed, A. K. M. M.

2016-07-12

Interfacial phenomena such as mass and type of the interstitial atom, nano scale material defect influence heat transfer and the effect become very significant with the reduction of the material size. Non Equilibrium Molecular Dynamics (NEMD) simulation was carried out in this study to investigate the effect of the interfacial phenomena on solid. Argon like solid was considered in this study and LJ potential was used for atomic interaction. Nanoparticles of different masses and different molecular defects were inserted inside the solid. From the molecular simulation, it was observed that a large interfacial mismatch due to change in mass inmore » the homogenous solid causes distortion of the phonon frequency causing increase in thermal resistance. Position of the doped nanoparticles have more profound effect on the thermal conductivity of the solid whereas influence of the mass ratio is not very significant. Interstitial atom positioned perpendicular to the heat flow causes sharp reduction in thermal conductivity. Structural defect caused by the molecular defect (void) also observed to significantly affect the thermal conductivity of the solid.« less

Confidence level in venipuncture and knowledge on causes of in vitro hemolysis among healthcare professionals

PubMed Central

Milutinović, Dragana; Andrijević, Ilija; Ličina, Milijana; Andrijević, Ljiljana

2015-01-01

Introduction This study aimed to assess confidence level of healthcare professionals in venipuncture and their knowledge on the possible causes of in vitro hemolysis. Materials and methods A sample of 94 healthcare professionals (nurses and laboratory technicians) participated in this survey study. A four-section questionnaire was used as a research instrument comprising general information for research participants, knowledge on possible causes of in vitro hemolysis due to type of material used and venipuncture technique and specimen handling, as well as assessment of healthcare professionals’ confidence level in their own ability to perform first and last venipuncture. Results The average score on the knowledge test was higher in nurses’ than in laboratory technicians (8.11 ± 1.7, and 7.4 ± 1.5, respectively). The difference in average scores was statistically significant (P = 0.035) and Cohen’s d in the range of 0.4 indicates that there is a moderate difference on the knowledge test among the health care workers. Only 11/94 of healthcare professionals recognized that blood sample collection from cannula and evacuated tube is method which contributes most to the occurrence of in vitro hemolysis, whereas most risk factors affecting occurrence of in vitro hemolysis during venipuncture were recognized. There were no significant differences in mean score on the knowledge test in relation to the confidence level in venipuncture (P = 0.551). Conclusion Confidence level at last venipuncture among both profiles of healthcare staff was very high, but they showed insufficient knowledge about possible factors affecting hemolysis due to materials used in venipuncture compared with factors due to venipuncture technique and handling of blood sample. PMID:26527124

Real time monitoring of powder blend bulk density for coupled feed-forward/feed-back control of a continuous direct compaction tablet manufacturing process.

PubMed

Singh, Ravendra; Román-Ospino, Andrés D; Romañach, Rodolfo J; Ierapetritou, Marianthi; Ramachandran, Rohit

2015-11-10

The pharmaceutical industry is strictly regulated, where precise and accurate control of the end product quality is necessary to ensure the effectiveness of the drug products. For such control, the process and raw materials variability ideally need to be fed-forward in real time into an automatic control system so that a proactive action can be taken before it can affect the end product quality. Variations in raw material properties (e.g., particle size), feeder hopper level, amount of lubrication, milling and blending action, applied shear in different processing stages can affect the blend density significantly and thereby tablet weight, hardness and dissolution. Therefore, real time monitoring of powder bulk density variability and its incorporation into the automatic control system so that its effect can be mitigated proactively and efficiently is highly desired. However, real time monitoring of powder bulk density is still a challenging task because of different level of complexities. In this work, powder bulk density which has a significant effect on the critical quality attributes (CQA's) has been monitored in real time in a pilot-plant facility, using a NIR sensor. The sensitivity of the powder bulk density on critical process parameters (CPP's) and CQA's has been analyzed and thereby feed-forward controller has been designed. The measured signal can be used for feed-forward control so that the corrective actions on the density variations can be taken before they can influence the product quality. The coupled feed-forward/feed-back control system demonstrates improved control performance and improvements in the final product quality in the presence of process and raw material variations. Copyright © 2015 Elsevier B.V. All rights reserved.

Accumulated lipids rather than the rigid cell walls impede the extraction of genetic materials for effective colony PCRs in Chlorella vulgaris

PubMed Central

2013-01-01

Background Failure of colony PCRs in green microalga Chlorella vulgaris is typically attributed to the difficulty in disrupting its notoriously rigid cell walls for releasing the genetic materials and therefore the development of an effective colony PCR procedure in C. vulgaris presents a challenge. Results Here we identified that colony PCR results were significantly affected by the accumulated lipids rather than the rigid cell walls of C. vulgaris. The higher lipids accumulated in C. vulgaris negatively affects the effective amplification by DNA polymerase. Based on these findings, we established a simple and extremely effective colony PCR procedure in C. vulgaris. By simply pipetting/votexing the pellets of C. vulgaris in 10 ul of either TE (10 mM Tris/1 mM EDTA) or 0.2% SDS buffer at room temperature, followed by the addition of 10 ul of either hexane or Phenol:Chloroform:Isoamyl Alcohol in the same PCR tube for extraction. The resulting aqueous phase was readily PCR-amplified as genomic DNA templates as demonstrated by successful amplification of the nuclear 18S rRNA and the chloroplast rbcL gene. This colony PCR protocol is effective and robust in C. vulgaris and also demonstrates its effectiveness in other Chlorella species. Conclusions The accumulated lipids rather than the rigid cell walls of C. vulgaris significantly impede the extraction of genetic materials and subsequently the effective colony PCRs. The finding has the potential to aid the isolation of high-quality total RNAs and mRNAs for transcriptomic studies in addition to the genomic DNA isolation in Chlorella. PMID:24219401

Effect of Different Esthetic Post-Core Materials on Color of Direct-Composite Restorations: A Preliminary Clinical Study.

PubMed

Ayna, Buket; Yılmaz, Berivan D; Izol, Bozan S; Ayna, Emrah; Tacir, İbrahim Halil

2018-06-15

BACKGROUND The purpose of this study was to determine the influence of 2 different esthetic post materials on the final color of direct-composite restorations by using a digital technique under in vivo conditions. MATERIAL AND METHODS We included 22 pulpless incisor teeth treated with conventionally cemented zirconia (n=11) and polyethylene fiber (n=11) posts in the study. Teeth were restored with a hybrid resin. The color of direct-composite restorations and contralateral control teeth was measured using a digital technique. The Commission Internationale de L'Eclairage, or CIE, L*a*b* and RGB color systems were investigated. Descriptive statistical analysis was performed for the CIE L*a*b* values. Color differences (ΔE) for the average L*, a*, and b* color parameters between every pair of groups were calculated (P>.05). RESULTS Significant differences were not found in the color difference luminosity (lum), R, G, B, and L* a* b* values between the zircon-rich glass fiber post (Z) and contralateral control teeth (Cz) (P>.05) and between the polyethylene fiber post (P) and contralateral control teeth (Cp) (P>.05). However, there was a statistically significant difference between the color a* values of the polyethylene fiber post (P) and contralateral control teeth (Cp) (p<0.05). Color differences (ΔE) between the zircon-rich glass fiber post (Z) and contralateral control teeth, and the polyethylene fiber post (P) and contralateral teeth were not statistically significant (P>.05). CONCLUSIONS Definitive restorations were equally affected by the 2 materials. Both materials can be used reliably in clinical practice. However, further research that focuses on the effect of intraoral conditions is needed.

Effects of packaging materials on the aroma stability of Thai 'tom yam' seasoning powder as determined by descriptive sensory analysis and gas chromatography-mass spectrometry.

PubMed

Leelaphiwat, Pattarin; Harte, Janice B; Auras, Rafael A; Ong, Peter Kc; Chonhenchob, Vanee

2017-04-01

Changes in the aroma characteristics of Thai 'tom yam' seasoning powder, containing lemongrass, galangal and kaffir lime leaf, as affected by different packaging materials were assessed using quantitative descriptive analysis (QDA) and gas chromatography-mass spectrometry (GC-MS). The descriptive aroma attributes for lemongrass, galangal and kaffir lime leaf powders were developed by the QDA panel. The mixed herb and spice seasoning powder was kept in glass jars closed with different packaging materials (Nylon 6, polyethylene terephthalate (PET) and polylactic acid (PLA)) stored at 38 °C (accelerated storage condition), and evaluated by the trained QDA panel during storage for 49 days. The descriptive words for Thai 'tom yam' seasoning powder developed by the trained panelists were lemongrass, vinegary and leafy for lemongrass, galangal and kaffir lime leaf dried powder, respectively. The aroma intensities significantly (P ≤ 0.05) decreased with increased storage time. However, the intensity scores for aroma attributes were not significantly (P > 0.05) different among the packaging materials studied. The major components in Thai 'tom yam' seasoning powder, quantified by GC-MS, were estragole, bicyclo[3.1.1]heptane, β-bisabolene, benzoic acid and 2-ethylhexyl salicylate. The concentrations of major aroma compounds significantly (P ≤ 0.05) decreased with storage time. Aroma stability of Thai 'tom yam' powder can be determined by descriptive sensory evaluation and GC-MS analysis. Nylon, PET and PLA exhibited similar aroma barrier properties against key aroma compounds in Thai 'tom yam'. This information can be used for prediction of aroma loss through packaging materials during storage of Thai 'tom yam'. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

230Th/U dating of Last Interglacial brain corals from Bonaire (southern Caribbean) using bulk and theca wall material

NASA Astrophysics Data System (ADS)

Obert, J. Christina; Scholz, Denis; Felis, Thomas; Brocas, William M.; Jochum, Klaus P.; Andreae, Meinrat O.

2016-04-01

We compared the suitability of two skeletal materials of the Atlantic brain coral Diploria strigosa for 230Th/U-dating: the commonly used bulk material comprising all skeletal elements and the denser theca wall material. Eight fossil corals of presumably Last Interglacial age from Bonaire, southern Caribbean Sea, were investigated, and several sub-samples were dated from each coral. For four corals, both the ages and the activity ratios of the bulk material and theca wall agree within uncertainty. Three corals show significantly older ages for their bulk material than for their theca wall material as well as substantially elevated 232Th content and (230Th/238U) ratios. The bulk material samples of another coral show younger ages and lower (230Th/238U) ratios than the corresponding theca wall samples. This coral also contains a considerable amount of 232Th. The application of the available open-system models developed to account for post-depositional diagenetic effects in corals shows that none of the models can successfully be applied to the Bonaire corals. The most likely explanation for this observation is that the assumptions of the models are not fulfilled by our data set. Comparison of the theca wall and bulk material data enables us to obtain information about the open-system processes that affected the corals. The corals showing apparently older ages for their bulk material were probably affected by contamination with a secondary (detrital) phase. The most likely source of the detrital material is carbonate sand. The higher (230Th/232Th) ratio of this material implies that detrital contamination would have a much stronger impact on the ages than a contaminant with a bulk Earth (230Th/232Th) ratio and that the threshold for the commonly applied 232Th reliability criterion would be much lower than the generally used value of 1 ng g-1. The coral showing apparently younger ages for its bulk material was probably influenced by more than one diagenetic process. A potential scenario is a combination of detrital contamination and U addition by secondary pore infillings. Our results show that the dense theca wall material of D. strigosa is generally less affected by post-depositional open-system behaviour and better suited for 230Th/U-dating than the bulk material. This is also obvious from the fact that all ages of theca wall material reflect a Last Interglacial origin (∼125 ka), whereas the bulk material samples are either substantially older or younger. However, for some corals, the 230Th/U-ages and activity ratios of the bulk material and the theca wall samples are similar. This shows that strictly reliable 230Th/U-ages can also be obtained from bulk material samples of exceptionally well-preserved corals. However, the bulk material samples more frequently show elevated activity ratios and ages than the corresponding theca wall samples. Our findings should be generally applicable to brain corals (Mussidae) that are found in tropical oceans worldwide and may enable reliable 230Th/U-dating of fossil corals with similar skeletal architecture, even if their bulk skeleton is altered by diagenesis. The 230Th/U-ages we consider reliable (120-130 ka), along with a recently published age of 118 ka, provide the first comprehensive dating of the elevated lower reef terrace at Bonaire (118-130 ka), which is in agreement in timing and duration with other Last Interglacial records.

Balneotherapy in Treatment of Spastic Upper Limb after Stroke

PubMed Central

Erceg-Rukavina, Tatjana; Stefanovski, Mihajlo

2015-01-01

Introduction: After stroke, spasticity is often the main problem that prevents functional recovery. Pain occurs in up to 70% of patients during the first year post-stroke. Materials and methods: A total of 70 patients (30 female and 45 male) mean age (65.67) participated in prospective, controlled study. Inclusion criteria: ischaemic stroke, developed spasticity of upper limb, post-stroke interval <6 months. Exclusion criteria: contraindications for balneotherapy and inability to follow commands. Experimental group (Ex) (n=35) was treated with sulphurous baths (31°-33°C) and controlled group (Co) with taped water baths, during 21 days. All patients were additionally treated with kinesitherapy and cryotherapy. The outcome was evaluated using Modified Ashworth scale for spasticity and VAS scale for pain. The significance value was sat at p<0.05. Goal: To find out the effects of balneotherapy with sulphurous bath on spasticity and pain in affected upper limb. Results: Reduction in tone of affected upper limb muscles was significant in Ex group (p<0.05). Pain decreased significantly in Ex-group (p<0.01). Conclusion: Our results show that balneotherapy with sulphurous water reduces spasticity and pain significantly and can help in treatment of post-stroke patients. PMID:25870474

Effects of raw material extrusion and steam conditioning on feed pellet quality and nutrient digestibility of growing meat rabbits.

PubMed

Liao, Kuoyao; Cai, Jingyi; Shi, Zhujun; Tian, Gang; Yan, Dong; Chen, Delin

2017-06-01

This study was conducted to investigate the effects of raw material extrusion and steam conditioning on feed pellet quality and nutrient digestibility of growing meat rabbits, in order to determine appropriate rabbit feed processing methods and processing parameters. In Exp. 1, an orthogonal design was adopted. Barrel temperature, material moisture content and feed rate were selected as test factors, and acid detergent fiber (ADF) content was selected as an evaluation index to research the optimum extrusion parameters. In Exp. 2, a two-factor design was adopted. Four kinds of rabbit feeds were processed and raw material extrusion adopted optimum extrusion parameters of Exp. 1. A total of 40 healthy and 42-day-old rabbits with similar weight were used in a randomized design, which consisted of 4 groups and 10 replicates in each group (1 rabbits in each replicate). The adaptation period lasted for 7 d, and the digestion trial lasted for 4 d. The results showed as follows: 1) ADF was significantly affected by barrel temperature ( P  < 0.05); the optimum extrusion parameters were barrel temperature 125 °C, moisture content 16% and feed rate 9 Hz. 2) Raw material extrusion and steam conditioning both significantly decreased powder percentage, pulverization ratio and protein solubility ( P  < 0.05), significantly improved hardness and starch gelatinization degree of rabbit feed ( P  < 0.05). They both had significant interaction effects on the processing quality of rabbit feed ( P  < 0.05). 3) Extrusion significantly improved the apparent digestibility of dry matter and total energy ( P  < 0.05). Extrusion and steam conditioning both significantly improved the apparent digestibility of crude fiber (CF), ADF and NDF ( P  < 0.05), but they had no interaction effects on the apparent digestibility of rabbit feed. Thus, using extrusion and steam conditioning technology at the same time in the weaning rabbits feed processing can improve the pellet quality and nutrient apparent digestibility of rabbit feed.

USGS reference materials

USGS Publications Warehouse

,

1995-01-01

Every year in the United States, millions of measurements are made on the chemical composition of items that affect us on a daily basis. Determining the accuracy of these measurements is based on the analysis of appropriate reference materials whose composition was previously determined through rigorous testing. Today, reference materials help us evaluate the composition of the food we eat, medicine we use, soil we grow our crops in, and hundreds of other products that affect our everyday lives.

Influence of collagen-fibril-based coatings containing decorin and biglycan on osteoblast behavior.

PubMed

Douglas, Timothy; Hempel, Ute; Mietrach, Carolin; Viola, Manuela; Vigetti, Davide; Heinemann, Sascha; Bierbaum, Susanne; Scharnweber, Dieter; Worch, Hartmut

2008-03-01

Collagen is used as a scaffold material for tissue engineering as well as a coating material for implants with a view to enhancing osseointegration by mimicry of the bone extracellular matrix in vivo. The biomimicry strategy can be taken further by incorporating the small leucine-rich proteoglycans (SLRPs) decorin and biglycan, which are expressed in bone. Both bind to fibrils during fibrillogenesis in vitro. In this study, the ability of collagen types I, II, and III to bind decorin and biglycan was compared. Collagen type II bound significantly more SLRPs in fibrils than collagen I and III, with more biglycan than decorin bound by all three collagen types. Therefore, type II fibrils with bound decorin or biglycan or neither were used to coat titanium surfaces. Bioavailability of SLRPs was confirmed by direct ELISA after SLRP biotinilation. The in vitro behavior of osteoblasts from rat calvaria (rOs) and human knee (hOs) cultured on different surfaces was compared. Proliferation and collagen synthesis were determined. Also, the influence of SLRPs on the formation of focal adhesions by rO was investigated. Biglycan enhanced the formation of focal adhesions after 2 and 24 h. Decorin and biglycan affected rO and hO proliferation and collagen synthesis differently. Biglycan stimulated hO proliferation significantly but had no effect on rO proliferation, and also inhibited rO collagen synthesis significantly while not affecting hO collagen synthesis. Decorin promoted hO proliferation slightly but did not influence rO proliferation. The results could be relevant when designing implant coatings or tissue engineering scaffolds. (c) 2007 Wiley Periodicals, Inc.

Dilatant effect enhancers for silica dispersions in poly(propylene glycols).

PubMed

Orawiec, Marcin; Kaczorowski, Marcin; Rokicki, Gabriel

2018-05-29

Shear thickening fluids have found many applications in energy damping materials such as sports guards and liquid body armors. Therefore, an additive which could tailor the dilatant properties of such fluids without significantly affecting other properties, especially zero shear viscosity, could significantly increase the versatility of protective materials based on shear thickening fluids. In this paper, poly(propylene glycols) (PPGs) diacetates are investigated as dilatant effect enhancers for nano-silica dispersions in poly(propylene glycols). The influence of the modifiers on rheological properties of the dispersion is studied and discussed. Additionally, FTIR and rheological properties measurements are conducted in order to determine relative interactions strength between hydroxyl groups of PPGs and silica and carbonyl groups of PPG diacetates. Our findings suggest that the relative attractive interaction strength in studied systems can be arranged in the following order: COCO < COOH < OHOH. Therefore, the addition of PPG diacetate hinders the attractive interactions between liquid and solid. We report that the addition of diacetates can lead both to enhancement and deterioration of dilatant effect depending on the concentration of the modifier and its chain length. Based on conducted measurements and literature data, mechanism explaining that phenomenon is suggested. As a result, we propose an easy to make and cheap dilatant effect enhancer for widely used shear thickening fluids which, when used in small amounts (1-2.5%), raises the viscosity jump drastically. Additionally, the presence of the modifier does not significantly affect the zero shear viscosity of the shear thickening fluid. Copyright © 2018 Elsevier Inc. All rights reserved.

Rocket salad (Diplotaxis and Eruca spp.) sensory analysis and relation with glucosinolate and phenolic content.

PubMed

Pasini, Federica; Verardo, Vito; Cerretani, Lorenzo; Caboni, Maria Fiorenza; D'Antuono, Luigi Filippo

2011-12-01

Salad crops of the Brassicaceae family, such as Diplotaxis tenuifolia and Eruca vesicaria, commonly referred to as 'rocket salads', have attracted considerable interest as culinary vegetables because of their strong flavour and their content of putative health-promoting compounds. Among such compounds, glucosinolates and phenolics are well-known phytochemicals with an important role also in determining the characteristic flavour of these species. In this study, to identify potentially high-value rocket salads, 37 cultivated types were examined for sensory characters and their relations with glucosinolate and phenolic contents, which ranged from 0.76 to 3.03 g kg(-1) dry weight (DW) and from 4.68 to 31.39 g kg(-1) DW, respectively. The perception of bitter taste was significantly affected by specific glucosinolates, namely progoitrin/epiprogoitrin and dimeric glucosativin. Aroma intensity was negatively related to glucoalyssin content, whereas pungency was significantly related to total glucosinolate content. Kaempferol-3-(2-sinapoyl-glucoside)-4'-glucoside was positively and significantly related to all flavour trait perceptions. Aroma intensity, pungency, crunchiness and juiciness were positively related to typical rocket salad flavour perception through a prominent direct effect. Aroma intensity, pungency, crunchiness and juiciness were strong determinants of overall rocket salad flavour perception. Visual traits also characterised sensory components. Bitterness, usually considered a negative flavour trait, was moderately perceived in the examined material, without negatively affecting typical flavour perception. In the range of the examined material, glucosinolate content did not contrast with typical flavour, demonstrating that good taste and putative health-promoting properties may coexist. Copyright © 2011 Society of Chemical Industry.

Survey of materials for hydrazine propulsion systems in multicycle extended life applications

NASA Technical Reports Server (NTRS)

Coulbert, C. D.; Yankura, G.

1972-01-01

An assessment is presented of materials compatibility data for hydrazine monopropellant propulsion systems applicable to the Space Shuttle vehicle missions. Materials were evaluated for application over a 10-yr/100-mission operational lifetime with minimum refurbishment. A general materials compatibility rating for a broad range of materials and several propellants based primarily on static liquid propellant immersion testing and an in-depth evaluation of hydrazine decomposition as a function of purity, temperature, material, surface conditions, etc., are presented. The most promising polymeric material candidates for propellant diaphragms and seals appear to have little effect on increasing hydrazine decomposition rates, but the materials themselves do undergo changes in physical properties which can affect their 10-yr performance in multicycle applications. The available data on these physical properties of elastomeric materials as affected by exposure to hydrazine or related environments are presented.

A data base describing low-gravity fluids and materials processing experiments

NASA Technical Reports Server (NTRS)

Winter, C. A.; Jones, J. C.

1992-01-01

A data base documenting information on approximately 600 fluids and materials processing experiments performed in a low-gravity environment has been prepared at NASA Marshall Space Flight Center (MSFC). The compilation was designed to document all such experimental efforts performed: (1) on U.S. manned space vehicles; (2) on payloads deployed from U.S. manned space vehicles; and (3) on all domestic and international sounding rocket programs (excluding those of the U.S.S.R. and China). Identification of major (reported) sources of significant anomalies during 100 of the experiments is reported and discussed. Further, a preliminary summary of the number of these 100 investigations which experienced an anomaly affecting a certain percentage of the experimental results/objectives is presented.

Variation in Pockels constants of silicate glass-ceramics prepared by perfect surface crystallization

NASA Astrophysics Data System (ADS)

Takano, Kazuya; Takahashi, Yoshihiro; Miyazaki, Takamichi; Terakado, Nobuaki; Fujiwara, Takumi

2018-01-01

We investigated the Pockels effect in polycrystalline materials consisting of highly oriented polar fresnoite-type Sr2TiSi2O8 fabricated using perfectly surface-crystallized glass-ceramics (PSC-GCs). The chemical composition of the precursor glass was shown to significantly affect the crystallized texture, e.g., the crystal orientation and appearance of amorphous nanoparasites in the domains, resulting in variations in the Pockels constants. Single crystals exhibiting spontaneous polarization possessed large structural anisotropy, leading to a strong dependence of the nonlinear-optical properties on the direction of polarized light. This study suggests that variations in the Pockels constants (r13 and r33) and tuning of the r13/r33 ratio can be realized in PSC-GC materials.

Effect of stacking fault energy on mechanism of plastic deformation in nanotwinned FCC metals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borovikov, Valery; Mendelev, Mikhail I.; King, Alexander H.

Starting from a semi-empirical potential designed for Cu, we have developed a series of potentials that provide essentially constant values of all significant (calculated) materials properties except for the intrinsic stacking fault energy, which varies over a range that encompasses the lowest and highest values observed in nature. In addition, these potentials were employed in molecular dynamics (MD) simulations to investigate how stacking fault energy affects the mechanical behavior of nanotwinned face-centered cubic (FCC) materials. The results indicate that properties such as yield strength and microstructural stability do not vary systematically with stacking fault energy, but rather fall into twomore » distinct regimes corresponding to 'low' and 'high' stacking fault energies.« less

Effect of stacking fault energy on mechanism of plastic deformation in nanotwinned FCC metals

DOE PAGES

Borovikov, Valery; Mendelev, Mikhail I.; King, Alexander H.; ...

2015-05-15

Starting from a semi-empirical potential designed for Cu, we have developed a series of potentials that provide essentially constant values of all significant (calculated) materials properties except for the intrinsic stacking fault energy, which varies over a range that encompasses the lowest and highest values observed in nature. In addition, these potentials were employed in molecular dynamics (MD) simulations to investigate how stacking fault energy affects the mechanical behavior of nanotwinned face-centered cubic (FCC) materials. The results indicate that properties such as yield strength and microstructural stability do not vary systematically with stacking fault energy, but rather fall into twomore » distinct regimes corresponding to 'low' and 'high' stacking fault energies.« less

Aerosolization of fungi, (1→3)-β-D glucan, and endotoxin from flood-affected materials collected in New Orleans homes

PubMed Central

Adhikari, Atin; Jung, Jaehee; Reponen, Tiina; Lewis, Jocelyn Suzanne; DeGrasse, Enjoli C.; Grimsley, L. Faye; Chew, Ginger L.; Grinshpun, Sergey A.

2015-01-01

Standing water and sediments remaining on flood-affected materials were the breeding ground for many microorganisms in flooded homes following Hurricane Katrina. The purpose of this laboratory study was to examine the aerosolization of culturable and total fungi, (1→3)-β-D glucan, and endotoxin from eight flood-affected floor and bedding materials collected in New Orleans homes, following Hurricane Katrina. Aerosolization was examined using the Fungal Spore Source Strength Tester (FSSST) connected to a BioSampler. Dust samples were collected by vacuuming. A two-stage cyclone sampler was used for size-selective analysis of aerosolized glucan and endotoxin. On average, levels of culturable fungi ranged from undetectable (lower limit = 8.3×104) to 2.6×105 CFU/m2; total fungi ranged from 2.07×105 to 1.6×106 spores/m2; (1→3)-β-D glucan and endotoxin were 2.0×103 – 2.9×104 ng/m2 and 7.0×102 – 9.3×104 EU/m2, respectively. The results showed that 5–15 min sampling is sufficient for detecting aerosolizable biocontaminants with the FSSST. Smaller particle size fractions (<1.0 μm and <1.8 μm) have levels of glucan and endotoxin comparable to larger (>1.8 μm) fractions, which raises additional exposure concerns. Vacuuming was found to overestimate inhalation exposure risks by a factor of approximately 102 for (1→3)-β-D glucan and by 103 to 104 for endotoxin as detected by the FSSST. The information generated from this study is important with respect to restoration and rejuvenation of the flood-affected areas in New Orleans. We believe the findings will be significant during similar disasters in other regions of the world including major coastal floods from tsunamis. PMID:19201399

Changes of electrical conductivity of the metal surface layer by the laser alloying with foreign elements

NASA Astrophysics Data System (ADS)

Kostrubiec, Franciszek; Pawlak, Ryszard; Raczynski, Tomasz; Walczak, Maria

1994-09-01

Laser treatment of the surface of materials is of major importance for many fields technology. One of the latest and most significant methods of this treatment is laser alloying consisting of introducing foreign atoms into the metal surface layer during the reaction of laser radiation with the surface. This opens up vast possibilities for the modification of properties of such a layer (obtaining layers of increased microhardness, increased resistance to electroerosion in an electric arc, etc.). Conductivity of the material is a very important parameter in case of conductive materials used for electrical contacts. The paper presents the results of studies on change in electrical conductivity of the surface layer of metals alloyed with a laser. A comparative analysis of conductivity of base metal surface layers prior to and following laser treatment has been performed. Depending on the base metal and the alloying element, optical treatment parameters allowing a required change in the surface layer conductivity have been selected. A very important property of the contact material is its resistance to plastic strain. It affects the real value of contact surface coming into contact and, along with the material conductivity, determines contact resistance and the amount of heat generated in place of contact. These quantities are directly related to the initiation and the course of an arc discharge, hence they also affect resistance to electroerosion. The parameter that reflects plastic properties with loads concentrated on a small surface, as is the case with a reciprocal contact force of two real surfaces with their irregularities being in contact, is microhardness. In the paper, the results of investigations into microhardness of modified surface layers compared with base metal microhardness have been presented.

To have or to learn? The effects of materialism on British and Chinese children's learning.

PubMed

Ku, Lisbeth; Dittmar, Helga; Banerjee, Robin

2014-05-01

This article presents a systematic attempt to examine the associations of materialism with learning in 9- to 11-year-old children in 2 countries of similar economic development but different cultural heritage. Using cross-sectional, longitudinal, and experimental methods, we test a theoretically driven model of associations among materialism, learning motivations, and learning outcomes. Convergent findings suggest that a materialist orientation in elementary school children lowers intrinsic learning motivations, fosters extrinsic learning motivations, and leads to poorer learning outcomes. Materialism was linked directly to lower exam performance, and this link was mediated by lower mastery and heightened performance goals, with patterns not differing between British and Hong Kong Chinese children (Study 1). A follow-up showed that initial materialism predicted worse exam grades 1 year later, suggesting a detrimental long-term effect on Chinese children's school performance (Study 2). We then tested relationships between materialism and learning experimentally, by priming a momentary (state) orientation toward materialism. Writing about material possessions and money affected Chinese children's learning motivations, so that they endorsed lower mastery and higher performance goals (Study 3). A video-diary materialism prime had significant effects on actual learning behaviors, leading British children to (a) choose a performance-oriented learning task over a mastery-oriented task and (b) give up on the task more quickly (Study 4). This research has important implications for personality psychology, educational policy, and future research.

IRIS Mariner 9 Data Revisited. 1; An Instrumental Effect

NASA Technical Reports Server (NTRS)

Formisano, V.; Grassi, D.; Piccioni, G.; Pearl, John; Bjoraker, G.; Conrath, B.; Hanel, R.

1999-01-01

Small spurious features are present in data from the Mariner 9 Infrared Interferometer Spectrometer (IRIS). These represent a low amplitude replication of the spectrum with a doubled wavenumber scale. This replication arises principally from an internal reflection of the interferogram at the input window. An algorithm is provided to correct for the effect, which is at the 2% level. We believe that the small error in the uncorrected spectra does not materially affect previous results; however, it may be significant for some future studies at short wavelengths. The IRIS spectra are also affected by a coding error in the original calibration that results in only positive radiances. This reduces the effectiveness of averaging spectra to improve the signal to noise ratio at small signal levels.

Oxygen vacancy diffusion in bulk SrTiO3 from density functional theory calculations

DOE PAGES

Zhang, Lipeng; Liu, Bin; Zhuang, Houlong; ...

2016-04-01

Point defects and point defect diffusion contribute significantly to the properties of perovskite materials. However, even for the prototypical case of oxygen vacancies in SrTiO 3 (STO), predictions vary widely. Here we present a comprehensive and systematic study of the diffusion barriers for this material. We use density functional theory (DFT) and assess the role of different cell sizes, density functionals, and charge states. Our results show that vacancy-induced octahedral rotations, which are limited by the boundary conditions of the supercell, can significantly affect the computed oxygen vacancy diffusion energy barrier. The diffusion energy barrier of a charged oxygen vacancymore » is lower than that of a neutral one. Unexpectedly, we find that with increasing supercell size, the effects of the oxygen vacancy charge state, the type of DFT exchange and correlation functional on the energy barrier diminish, and the different DFT predictions asymptote to a value in the range of 0.39-0.49 eV. This work provides important insight and guidance that should be considered for investigations of point defect diffusion in other perovskite materials and in oxide superlattices.« less

Development of Equivalent Material Properties of Microbump for Simulating Chip Stacking Packaging

PubMed Central

Lee, Chang-Chun; Tzeng, Tzai-Liang; Huang, Pei-Chen

2015-01-01

A three-dimensional integrated circuit (3D-IC) structure with a significant scale mismatch causes difficulty in analytic model construction. This paper proposes a simulation technique to introduce an equivalent material composed of microbumps and their surrounding wafer level underfill (WLUF). The mechanical properties of this equivalent material, including Young’s modulus (E), Poisson’s ratio, shear modulus, and coefficient of thermal expansion (CTE), are directly obtained by applying either a tensile load or a constant displacement, and by increasing the temperature during simulations, respectively. Analytic results indicate that at least eight microbumps at the outermost region of the chip stacking structure need to be considered as an accurate stress/strain contour in the concerned region. In addition, a factorial experimental design with analysis of variance is proposed to optimize chip stacking structure reliability with four factors: chip thickness, substrate thickness, CTE, and E-value. Analytic results show that the most significant factor is CTE of WLUF. This factor affects microbump reliability and structural warpage under a temperature cycling load and high-temperature bonding process. WLUF with low CTE and high E-value are recommended to enhance the assembly reliability of the 3D-IC architecture. PMID:28793495

Selection of Wire Electrical Discharge Machining Process Parameters on Stainless Steel AISI Grade-304 using Design of Experiments Approach

NASA Astrophysics Data System (ADS)

Lingadurai, K.; Nagasivamuni, B.; Muthu Kamatchi, M.; Palavesam, J.

2012-06-01

Wire electrical discharge machining (WEDM) is a specialized thermal machining process capable of accurately machining parts of hard materials with complex shapes. Parts having sharp edges that pose difficulties to be machined by the main stream machining processes can be easily machined by WEDM process. Design of Experiments approach (DOE) has been reported in this work for stainless steel AISI grade-304 which is used in cryogenic vessels, evaporators, hospital surgical equipment, marine equipment, fasteners, nuclear vessels, feed water tubing, valves, refrigeration equipment, etc., is machined by WEDM with brass wire electrode. The DOE method is used to formulate the experimental layout, to analyze the effect of each parameter on the machining characteristics, and to predict the optimal choice for each WEDM parameter such as voltage, pulse ON, pulse OFF and wire feed. It is found that these parameters have a significant influence on machining characteristic such as metal removal rate (MRR), kerf width and surface roughness (SR). The analysis of the DOE reveals that, in general the pulse ON time significantly affects the kerf width and the wire feed rate affects SR, while, the input voltage mainly affects the MRR.

Advances in understanding of high- Z material erosion and re-deposition in low- Z wall environment in DIII-D

DOE PAGES

Ding, R.; Rudakov, D. L.; Stangeby, P. C.; ...

2017-03-24

Dedicated DIII-D experiments coupled with modeling reveal that the net erosion rate of high-Z materials, i.e. Mo and W, is strongly affected by carbon concentration in the plasma and the magnetic pre-sheath properties. We have investigated different methods such as electrical biasing and local gas injection to control high-Z material erosion. The net erosion rate of high-Z materials is significantly reduced due to the high local re-deposition ratio. The ERO modeling shows that the local re-deposition ratio is mainly controlled by the electric field and plasma density within the magnetic pre-sheath. The net erosion can be significantly suppressed by reducingmore » the sheath potential drop. A high carbon impurity concentration in the background plasma is also found to reduce the net erosion rate of high-Z materials. Both DIII-D experiments and modeling show that local 13CH 4 injection can create a carbon coating on the metal surface. The profile of 13C deposition provides quantitative information on radial transport due to E × B drift and the cross-field diffusion. The deuterium gas injection upstream of the W sample can reduce W net erosion rate by plasma perturbation. The inter-ELM W erosion we measured in H-mode plasmas, rates at different radial locations are well reproduced by ERO modeling taking into account charge-state-resolved carbon ion flux in the background plasma calculated using the OEDGE code.« less

Characterization of piezocrystals for practical configurations with temperature- and pressure-dependent electrical impedance spectroscopy.

PubMed

Qiu, Zhen; Sadiq, Muhammad R; Démoré, Christine; Parker, Michelle F; Marin, Pablo; Mayne, Keith; Cochran, Sandy

2011-09-01

Piezoelectric single crystal materials such as (x)Pb(Mg(1/3)Nb(2/3))O(3-)(1-x)PbTiO(3) (PMN-PT) have, by some measures, significantly better performance than established piezoelectric ceramics for ultrasound applications. However, they are also subject to phase transitions affecting their behavior at temperatures and pressures encountered in underwater sonar and actuator applications and in non-destructive testing at elevated temperatures. Materials with modified compositions to reduce these problems are now under development, but application-oriented characterization techniques need further attention. Characterization with temperature variation has been reported extensively, but the range of parameters measured is often limited and the effects of pressure variation have received almost no attention. Furthermore, variation in properties between samples is now rarely reported. The focus of this paper is an experimental system set up with commercially available equipment and software to carry out characterization of piezoelectric single crystals with variation in temperature, pressure, and electrical bias fields found in typical practical use. We illustrate its use with data from bulk thickness-mode PMN-29%PT samples, demonstrating variation among nominally identical samples and showing not only the commonly reported changes in permittivity with temperature for bulk material but also significant and complicated changes with pressure and bias field and additional ultrasonic modes which are attributed to material phase changes. The insight this provides may allow the transducer engineer to accelerate new material adoption in devices.

Infrared Thermography Sensor for Temperature and Speed Measurement of Moving Material.

PubMed

Usamentiaga, Rubén; García, Daniel Fernando

2017-05-18

Infrared thermography offers significant advantages in monitoring the temperature of objects over time, but crucial aspects need to be addressed. Movements between the infrared camera and the inspected material seriously affect the accuracy of the calculated temperature. These movements can be the consequence of solid objects that are moved, molten metal poured, material on a conveyor belt, or just vibrations. This work proposes a solution for monitoring the temperature of material in these scenarios. In this work both real movements and vibrations are treated equally, proposing a unified solution for both problems. The three key steps of the proposed procedure are image rectification, motion estimation and motion compensation. Image rectification calculates a front-parallel projection of the image that simplifies the estimation and compensation of the movement. Motion estimation describes the movement using a mathematical model, and estimates the coefficients using robust methods adapted to infrared images. Motion is finally compensated for in order to produce the correct temperature time history of the monitored material regardless of the movement. The result is a robust sensor for temperature of moving material that can also be used to measure the speed of the material. Different experiments are carried out to validate the proposed method in laboratory and real environments. Results show excellent performance.

Infrared Thermography Sensor for Temperature and Speed Measurement of Moving Material

PubMed Central

Usamentiaga, Rubén; García, Daniel Fernando

2017-01-01

Infrared thermography offers significant advantages in monitoring the temperature of objects over time, but crucial aspects need to be addressed. Movements between the infrared camera and the inspected material seriously affect the accuracy of the calculated temperature. These movements can be the consequence of solid objects that are moved, molten metal poured, material on a conveyor belt, or just vibrations. This work proposes a solution for monitoring the temperature of material in these scenarios. In this work both real movements and vibrations are treated equally, proposing a unified solution for both problems. The three key steps of the proposed procedure are image rectification, motion estimation and motion compensation. Image rectification calculates a front-parallel projection of the image that simplifies the estimation and compensation of the movement. Motion estimation describes the movement using a mathematical model, and estimates the coefficients using robust methods adapted to infrared images. Motion is finally compensated for in order to produce the correct temperature time history of the monitored material regardless of the movement. The result is a robust sensor for temperature of moving material that can also be used to measure the speed of the material. Different experiments are carried out to validate the proposed method in laboratory and real environments. Results show excellent performance. PMID:28524110

[Effects of laser solid forming of porous titanium on proliferation of osteoblast and RANKL/OPG expression].

PubMed

Chen, Hui; Du, Shanshan; Zhen, Ping; Li, Xusheng; Liang, Xiaoyan; Fan, Lijuan; Jiang, Jie; Yang, Haiou; Liu, Jun

2016-12-28

To evaluate the effect of laser solid forming (LSF) of porous titanium on receptor activator of NF-κB ligand (RANKL)/osteoprorotegerin (OPG) expression and osteoblast cells growth.
 Methods: The DMEM and sterile saline were used for porous titanium extract. The osteoblast cells were cultured in the extract while equal amount of  DMEM and sterile saline were added to the control group. The growth of the cells were observed under an inverted phase contrast microscope. MTT was used to detect the growth inhibitory rates. The adhesion capacity of osteoblasts were measured. The growth in the material surface was examined by the electron microscope, and the expressions of RANKL and OPG were determined by Westen blot.
 Results: At the first day, the osteoblast proliferation rate was significantly different (P<0.05), at the fourth and seventh day, the osteoblast proliferation rate was not significantly affected in the LSF group (P>0.05); at each time point, the osteoblast proliferation rate were significantly different between the two groups (P<0.05). Compared with the control group, RANKL and OPG protein expression were not significantly different (P>0.05). The laser solid forming of porous titanium showed well bone compatibility.
 Conclusion: The porous titanium did not affect osteoblast proliferation due to its well bone compatibility. It did not affect the OPG/RANKL/RANK-axis system of bone metabolism, exibiting a wide applicable prospect for tissue engineering.

Advanced Techniques for Ultrasonic Imaging in the Presence of Material and Geometrical Complexity

NASA Astrophysics Data System (ADS)

Brath, Alexander Joseph

The complexity of modern engineering systems is increasing in several ways: advances in materials science are leading to the design of materials which are optimized for material strength, conductivity, temperature resistance etc., leading to complex material microstructure; the combination of additive manufacturing and shape optimization algorithms are leading to components with incredibly intricate geometrical complexity; and engineering systems are being designed to operate at larger scales in ever harsher environments. As a result, at the same time that there is an increasing need for reliable and accurate defect detection and monitoring capabilities, many of the currently available non-destructive evaluation techniques are rendered ineffective by this increasing material and geometrical complexity. This thesis addresses the challenges posed by inspection and monitoring problems in complex engineering systems with a three-part approach. In order to address material complexities, a model of wavefront propagation in anisotropic materials is developed, along with efficient numerical techniques to solve for the wavefront propagation in inhomogeneous, anisotropic material. Since material and geometrical complexities significantly affect the ability of ultrasonic energy to penetrate into the specimen, measurement configurations are tailored to specific applications which utilize arrays of either piezoelectric (PZT) or electromagnetic acoustic transducers (EMAT). These measurement configurations include novel array architectures as well as the exploration of ice as an acoustic coupling medium. Imaging algorithms which were previously developed for isotropic materials with simple geometry are adapted to utilize the more powerful wavefront propagation model and novel measurement configurations.

Craft Stick Beams

NASA Technical Reports Server (NTRS)

Karplus, Alan K.

1996-01-01

The objective of this exercise is to provide a phenomenological 'hands-on' experience that shows how geometry can affect the load carrying capacity of a material used in construction, how different materials have different failure characteristics, and how construction affects the performance of a composite material. This will be accomplished by building beams of a single material and composite beams of a mixture of materials (popsicle sticks, fiberboard sheets, and tongue depressors); testing these layered beams to determine how and where they fail; and based on the failure analysis, designing a layered beam that will fail in a predicted manner. The students will learn the effects of lamination, adhesion, and geometry in layered beam construction on beam strength and failure location.

Antiproliferative effects of fresh and thermal processed green and red cultivars of curly kale (Brassica oleracea L. convar. acephala var. sabellica).

PubMed

Olsen, Helle; Grimmer, Stine; Aaby, Kjersti; Saha, Shikha; Borge, Grethe Iren A

2012-08-01

Brassica vegetables contain a diverse range of phytochemicals with biological properties such as antioxidant and anticancer activity. However, knowledge about how biological activities are affected by processing is lacking. A green cultivar and a red cultivar of curly kale were evaluated for water/methanol-soluble phytochemicals before and after processing involving blanching, freeze storage, and boil-in-bag heat treatment. In both kale cultivars, processing resulted in a significant decrease of total phenolics, antioxidant capacity, and content and distribution of flavonols, anthocyanins, hydroxycinnamic acids, glucosinolates, and vitamin C. Interestingly, the red curly kale cultivar had a higher capacity to withstand thermal loss of phytochemicals. The extracts of both green and red curly kale inhibited the cell proliferation of three human colon cancer cell lines (Caco-2, HT-29, and HCT 116). However, extracts from fresh plant material had a significantly stronger antiproliferative effect than extracts from processed plant material.

Remote sensing of permafrost and geological hazards in Alaska

NASA Technical Reports Server (NTRS)

Ferrians, O. J., Jr. (Principal Investigator)

1973-01-01

The author has identified the following significant results. The study of the ERTS-1 imagery of Alaska indicates the following: that areas of different topographic expression affecting the distribution and character of permafrost can be distinguished clearly; that on the Arctic North Slope, regional differences in the distribution and character of permafrost-related oriented thaw lakes can be observed; that the distribution of certain types of geologic materials having a significant effect on the character of permafrost can be delineated on a regional scale; and that the resolution of the imagery is adequate to identify large scale geologic hazards such as landslides, glacier-dammed lakes, aufeis fields, etc. The information concerning the distribution and character of permafrost and geologic hazards to the gained in accomplishing the objectives of this project will be an invaluable aid in solving engineering-geologic and environmental problems related to route and site selection for structures such as roads, railroads, pipelines, and large installations; to distribution of natural construction materials; and to construction and maintenance.

Medical Student Dissection of Cadavers Improves Performance on Practical Exams but not on the NBME Anatomy Subject Exam.

PubMed

Sargent Jones, Leslie; Paulman, Lance E; Thadani, Raj; Terracio, Louis

2001-12-01

We have examined whether cadaver dissection by first year medical students (MIs) affected their performance in two test measures: the NBME Gross Anatomy and Embryology Subject Exam (dissection-relevant questions only), and practical exams given at the end of each major section within the course. The dissections for the entire course were divided into 18 regional dissection units and each student was assigned to dissect one third of the regional units; the other two-thirds of the material was learned from the partner-prosected cadavers. Performance for each student on the exams was then assessed as a function of the regions those students actually dissected. While the results indicated a small performance advantage for MIs answering questions on material they had dissected on the NBME Subject Exam questions relevant to dissection (78-88% of total exam), the results were not statistically significant. However, a similar, small performance advantage on the course practical exams was highly significant.

Study on hydraulic exciting vibration due to flexible valve in pump system with method of characteristics in the time domain

NASA Astrophysics Data System (ADS)

Yu, Y. H.; Liu, D.; Yang, X. F.; Si, J.

2017-08-01

To analyse the flow characteristics of leakage as well as the mechanism of selfexcited vibration in valves, the method of characteristics was used to assess the effect of flexible valve leakage on the self-excited vibration in water-supply pump system. Piezometric head in upstream of the valve as a function of time was obtained. Two comparative schemes were proposed to simulate the process of self-excited vibration by changing the length, the material of the pipeline and the leakage of valves in the above pump system. It is shown that the length and material of the pipe significantly affect the amplitude and cycle of self-excited vibration as well as the increasing rate of the vibration amplitude. In addition, the leakage of the valve has little influence on the amplitude and cycle of self-excited vibration, but has a significant effect on the increasing rate of vibration amplitude. A pipe explosion accident may occur without the inhibiting of self-excited vibration.

Longitudinal evaluation of the microleakage of dentin bonding agents used to seal resected root apices.

PubMed

Vignaroli, P A; Anderson, R W; Pashley, D H

1995-10-01

A material that bonds to dentin and seals both the root canal and exposed dentinal tubules would be desirable following root resection. The purpose of this study was to measure the sealing ability of four dentin bonding agents on the resected root end. The bonding systems evaluated were Amalgambond (AMB), Scotchbond Multi-Purpose (SMP), Prisma Universal Bond 3 (PUB 3), and All-Bond 2 (AB2). All materials were applied directly to the resected root end without a class I preparation. One-half of the roots in each group were contaminated with human blood before bonding. Microleakage was measured using fluid filtration at various time intervals from 1 to 24 wk. Results indicated that all dentin bonding agents significantly reduced apical microleakage compared with prebonded controls at all time intervals. Blood contamination did not adversely affect the sealing ability of AMB, PUB 3, or SMP. The blood-contaminated AB2 group displayed significantly greater microleakage after 12 and 24 wk than the uncontaminated roots.

Lack of deleterious effect of slow-release sodium fluoride treatment on cortical bone histology and quality in osteoporotic patients

NASA Technical Reports Server (NTRS)

Zerwekh, J. E.; Antich, P. P.; Sakhaee, K.; Prior, J.; Gonzales, J.; Gottschalk, F.; Pak, C. Y.

1992-01-01

We evaluated the effects of intermittent slow-release sodium fluoride (SRNaF) and continuous calcium citrate therapy on cortical bone histology, reflection ultrasound velocity (material strength) and back-scattered electron image analysis (BEI) in 26 osteoporotic patients before and following therapy. All measurements were made on transiliac crest bone biopsies obtained before and following 2 years of therapy in each patient. For all 26 patients there were no significant changes in cortical bone histomorphometric parameters. In 15 patients in whom bone material quality was assessed by reflection ultrasound, there was no change in velocity (4000 +/- 227 SD to 4013 +/- 240 m/s). BEI disclosed no mineralization defects or the presence of woven bone. Mean atomic number (density) of bone increased slightly, but significantly (9.261 +/- 0.311 to 9.457 +/- 0.223, P = 0.031). While these changes are less marked than those observed for cancellous bone, they indicate that this form of therapy does not adversely affect cortical bone remodelling.

Optical polarimetric properties of the Echo 2 and PAGEOS 1 engineering surfaces. M.S. Thesis - Virginia Univ.

NASA Technical Reports Server (NTRS)

Lee, R. B., III

1972-01-01

Experimental investigations of the percent polarization of sunlight reflected from the surfaces of each of the Echo 2 Satellite and PAGEOS (Passive Geodetic Earth Orbiting Satellite) were performed to determine the stability of their surfaces in the space environment. The Echo 2 surface material was amorphous phosphate chemically bonded to a rolled aluminum substrate while the PAGEOS 1 surface material is vapor deposited aluminum on a poly (ethylene terephthalate) film. The stability of the satellites' surfaces was analyzed by comparing the light polarizing properties of the satellites, to those of test surfaces representative of the satellites' surfaces. The properties of flat test surfaces were measured experimentally in the laboratory, and the effects of surface strain, surface geometry, and vacuum upon these properties were examined. The laboratory analyses revealed that the polarization properties of the Echo 2 surface were significantly affected by surface geometry and vacuum, and that the properties of the PAGEOS 1 surface were not significantly altered by any of the above mechanisms.

An experimental study of flank wear in the end milling of AISI 316 stainless steel with coated carbide inserts

NASA Astrophysics Data System (ADS)

Odedeyi, P. B.; Abou-El-Hossein, K.; Liman, M.

2017-05-01

Stainless steel 316 is a difficult-to-machine iron-based alloys that contain minimum of about 12% of chromium commonly used in marine and aerospace industry. This paper presents an experimental study of the tool wear propagation variations in the end milling of stainless steel 316 with coated carbide inserts. The milling tests were conducted at three different cutting speeds while feed rate and depth of cut were at (0.02, 0.06 and 01) mm/rev and (1, 2 and 3) mm, respectively. The cutting tool used was TiAlN-PVD-multi-layered coated carbides. The effects of cutting speed, cutting tool coating top layer and workpiece material were investigated on the tool life. The results showed that cutting speed significantly affected the machined flank wears values. With increasing cutting speed, the flank wear values decreased. The experimental results showed that significant flank wear was the major and predominant failure mode affecting the tool life.

Chain dynamics and nanoparticle motion in attractive polymer nanocomposites subjected to large deformations.

PubMed

Senses, Erkan; Tyagi, Madhusudan; Natarajan, Bharath; Narayanan, Suresh; Faraone, Antonio

2017-11-08

The effect of large deformation on the chain dynamics in attractive polymer nanocomposites was investigated using neutron scattering techniques. Quasi-elastic neutron backscattering measurements reveal a substantial reduction of polymer mobility in the presence of attractive, well-dispersed nanoparticles. In addition, large deformations are observed to cause a further slowing down of the Rouse rates at high particle loadings, where the interparticle spacings are slightly smaller than the chain dimensions, i.e. in the strongly confined state. No noticeable change, however, was observed for a lightly confined system. The reptation tube diameter, measured by neutron spin echo, remained unchanged after shear, suggesting that the level of chain-chain entanglements is not significantly affected. The shear-induced changes in the interparticle bridging reflect the slow nanoparticle motion measured by X-ray photon correlation spectroscopy. These results provide a first step for understanding how large shear can significantly affect the segmental motion in nanocomposites and open up new opportunities for designing mechanically responsive soft materials.

Chain dynamics and nanoparticle motion in attractive polymer nanocomposites subjected to large deformations

DOE PAGES

Senses, Erkan; Tyagi, Madhusudan; Natarajan, Bharath; ...

2017-09-28

The effect of large deformation on the chain dynamics in attractive polymer nanocomposites was investigated using neutron scattering techniques. Quasielastic neutron backscattering measurements reveal a substantial reduction of polymer mobility in the presence of attractive, well-dispersed nanoparticles. Additionally, large deformations are observed to cause a further slowing down of the Rouse rates at high particle loadings, where the interparticle spacings are slightly smaller than the chain dimensions, i.e. in the strongly confined state. No noticeable change, however, was observed for a lightly confined system. The reptation tube diameter, measured by neutron spin echo, remained unchanged after shear, suggesting that themore » level of chain-chain entanglements is not significantly affected. The shearinduced changes in the interparticle bridging reflects on the slow nanoparticle motion measured by X-ray photon correlation spectroscopy. These results provide a first step for understanding how large shear can significantly affect the segmental motion in nanocomposites and open up new opportunities for designing mechanically responsive soft materials.« less

Chain dynamics and nanoparticle motion in attractive polymer nanocomposites subjected to large deformations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Senses, Erkan; Tyagi, Madhusudan; Natarajan, Bharath

The effect of large deformation on the chain dynamics in attractive polymer nanocomposites was investigated using neutron scattering techniques. Quasielastic neutron backscattering measurements reveal a substantial reduction of polymer mobility in the presence of attractive, well-dispersed nanoparticles. Additionally, large deformations are observed to cause a further slowing down of the Rouse rates at high particle loadings, where the interparticle spacings are slightly smaller than the chain dimensions, i.e. in the strongly confined state. No noticeable change, however, was observed for a lightly confined system. The reptation tube diameter, measured by neutron spin echo, remained unchanged after shear, suggesting that themore » level of chain-chain entanglements is not significantly affected. The shearinduced changes in the interparticle bridging reflects on the slow nanoparticle motion measured by X-ray photon correlation spectroscopy. These results provide a first step for understanding how large shear can significantly affect the segmental motion in nanocomposites and open up new opportunities for designing mechanically responsive soft materials.« less

A Quasi-Experimental Study of Two Selected Units of the Industrial Arts Curriculum Project Materials to Determine the Measurable Additive Effects of a Unit on Design in Manfacturing Technology upon a Similar Unit on Design in Construction Technology.

ERIC Educational Resources Information Center

Kuwik, Paul David

The purpose of the study was to determine whether exposing junior high school students to a unit on design in construction technology and to a unit on design in manufacturing technology significantly affects their achievement on a test measuring "Technological Principles of Design" when compared to a group of junior high school students exposed…

Novel Process Revolutionizes Welding Industry

NASA Technical Reports Server (NTRS)

2008-01-01

Glenn Research Center, Delphi Corporation, and the Michigan Research Institute entered into a research project to study the use of Deformation Resistance Welding (DRW) in the construction and repair of stationary structures with multiple geometries and dissimilar materials, such as those NASA might use on the Moon or Mars. Traditional welding technologies are burdened by significant business and engineering challenges, including high costs of equipment and labor, heat-affected zones, limited automation, and inconsistent quality. DRW addresses each of those issues, while drastically reducing welding, manufacturing, and maintenance costs.

Reduced brightness contrast as a reading aid.

PubMed

Giddings, E H; Carmean, S L

1989-10-01

A standard reading comprehension test, modified by printing half of the material on medium grey paper to lower the contrast of print-to-page, was administered to 54 college students, 21 of whom had previously been diagnosed as learning disabled. Comprehension of the control group was little affected by the contrast, but the mean score for the learning disabled students was 10% higher on the pages with reduced contrast. This is congruent with Meares's 1980 clinical observations that reducing contrast significantly aids some readers.

Iron chalcogenide superconductors at high magnetic fields

PubMed Central

Lei, Hechang; Wang, Kefeng; Hu, Rongwei; Ryu, Hyejin; Abeykoon, Milinda; Bozin, Emil S; Petrovic, Cedomir

2012-01-01

Iron chalcogenide superconductors have become one of the most investigated superconducting materials in recent years due to high upper critical fields, competing interactions and complex electronic and magnetic phase diagrams. The structural complexity, defects and atomic site occupancies significantly affect the normal and superconducting states in these compounds. In this work we review the vortex behavior, critical current density and high magnetic field pair-breaking mechanism in iron chalcogenide superconductors. We also point to relevant structural features and normal-state properties. PMID:27877518

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buechler, Elizabeth D.; Pallin, Simon B.; Boudreaux, Philip R.

The indoor air temperature and relative humidity in residential buildings significantly affect material moisture durability, HVAC system performance, and occupant comfort. Therefore, indoor climate data is generally required to define boundary conditions in numerical models that evaluate envelope durability and equipment performance. However, indoor climate data obtained from field studies is influenced by weather, occupant behavior and internal loads, and is generally unrepresentative of the residential building stock. Likewise, whole-building simulation models typically neglect stochastic variables and yield deterministic results that are applicable to only a single home in a specific climate. The

An innovative chairside bleaching protocol for treating stained dentition: initial results.

PubMed

Miara, P

2000-09-01

For years, investigators have attempted to develop a predictable means of bleaching pathologically and nonpathologically stained dentition. While previous efforts have modified the concentration of the bleaching material, the duration of the procedure, and the manner by which the bleaching agent is activated, the ability to affect a significant shade improvement remains an elusive objective. This article demonstrates an innovative technique used to influence the penetration of oxygen ions into the tooth enamel, which may resolve this clinical dilemma.

An improved method for isolating viruses from asymptomatic carrier fish

USGS Publications Warehouse

Amend, Donald F.; Pietsch, John P.

1972-01-01

This paper describes a method using elevated levels of penicillin, streptomycin, and nystatin instead of filters to control bacteria and mold contaminants in specimens processed for virus isolation. Filters were shown to significantly reduce the virus concentration. Virus and tissue cultures were not affected by this procedure. In field tests nearly three times more specimens were positive for virus with this method than with the widely used filter technique. Moreover, the cost of materials was less. This method is recommended for inspection and certification purposes.

Standards, Regulation and Registration of Dental Laboratories. An Industry Update.

PubMed

Giovannone, Paul L

2015-01-01

State dental associations are showing increased interest in maintaining current standards and regulations affecting the dental laboratory industry as mandated by the Food and Drug Administration. The domestic dental laboratory industry is being significantly stressed by foreign competition, rapid technology development and unprecedented consolidation, which are changing the way that prosthetic devices and restorations are manufactured and delivered to dentists. Of paramount importance to the prescribing dentist is the accurate documentation of the source and materials being used in prostheses being delivered to patients.

42 CFR 493.1252 - Standard: Test systems, equipment, instruments, reagents, materials, and supplies.

Code of Federal Regulations, 2011 CFR

2011-10-01

... electrical current that adversely affect patient test results and test reports. (c) Reagents, solutions, culture media, control materials, calibration materials, and other supplies, as appropriate, must be... proper use. (d) Reagents, solutions, culture media, control materials, calibration materials, and other...

42 CFR 493.1252 - Standard: Test systems, equipment, instruments, reagents, materials, and supplies.

Code of Federal Regulations, 2012 CFR

2012-10-01

... electrical current that adversely affect patient test results and test reports. (c) Reagents, solutions, culture media, control materials, calibration materials, and other supplies, as appropriate, must be... proper use. (d) Reagents, solutions, culture media, control materials, calibration materials, and other...

42 CFR 493.1252 - Standard: Test systems, equipment, instruments, reagents, materials, and supplies.

Code of Federal Regulations, 2013 CFR

2013-10-01

... electrical current that adversely affect patient test results and test reports. (c) Reagents, solutions, culture media, control materials, calibration materials, and other supplies, as appropriate, must be... proper use. (d) Reagents, solutions, culture media, control materials, calibration materials, and other...

Comparative effects of graphene and graphene oxide on copper toxicity to Daphnia magna: Role of surface oxygenic functional groups.

PubMed

Liu, Yingying; Fan, Wenhong; Xu, Zhizhen; Peng, Weihua; Luo, Shenglian

2018-05-01

Although the risk of graphene materials to aquatic organisms has drawn wide attention, the combined effects of graphene materials with other contaminants such as toxic metals, which may bring about more serious effects than graphene materials alone, have seldom been explored. Herein, the effects of graphene (GN) and graphene oxide (GO, an important oxidized derivative of graphene) on copper (Cu) toxicity to Daphnia magna were systematically investigated. The results indicated that GN remarkably increased the Cu accumulation in D. magna and enhanced the oxidative stress injury caused by Cu, whereas did not significantly alter D. magna acute mortality within the tested Cu concentrations (0-200 μg L -1 ). On the contrary, GO significantly decreased the Cu accumulation in D. magna and alleviated the oxidative stress injury caused by Cu. Meanwhile, the presence of GO significantly reduced the mortality of D. magna when Cu concentration exceeded 50 μg L -1 . The different effects of GN and GO on Cu toxicity were possibly dependent on the action of surface oxygenic functional group. Because of the introduction of surface oxygenic functional groups, the adsorption ability to metal ions, stability in water and interaction mode with organisms of GO are quite different from that of GN, causing different effects on Cu toxicity. This study provides important information on the bioavailability and toxicity of heavy metals as affected by graphene materials in natural water. Copyright © 2017 Elsevier Ltd. All rights reserved.

Seasonal survey of the composition and degradation state of particulate organic matter in the Rhone River using lipid tracers

NASA Astrophysics Data System (ADS)

Galeron, M.-A.; Amiraux, R.; Charriere, B.; Radakovitch, O.; Raimbault, P.; Garcia, N.; Lagadec, V.; Vaultier, F.; Rontani, J.-F.

2014-10-01

Lipid tracers including fatty acids, hydroxyacids, n-alkanols, sterols and triterpenoids were used to determine the origin and fate of suspended particulate organic matter (POM) collected in the Rhone River (France). This seasonal survey (April 2011 to May 2013) revealed a year-round strong terrigenous contribution to the plant-derived particulate organic matter (POM), with significant algal inputs observed in March and attributed to phytoplanktonic blooms likely dominated by diatoms. Major terrigenous contributors to our samples are gymnosperms, and more precisely their roots and stems, as evidenced by the presence of high proportions of ω-hydroxydocosanoic acid (a suberin biomarker). The high amounts of coprostanol detected clearly show that the Rhone River is significantly affected by sewage waters. Specific sterol degradation products were quantified and used to assess the part of biotic and abiotic degradation of POM within the river. Plant-derived organic matter appears to be mainly affected by photo-oxidation and autoxidation (free radical oxidation), while organic matter of human origin, evidenced by the presence of coprostanol, is clearly more prone to bacterial degradation. Despite the involvement of an intense autoxidation-inducing homolytic cleavage of peroxy bonds, a significant proportion of hydroperoxides is still intact in higher plant debris. These compounds could affect the degradation of terrestrial material by inducing an intense autoxidation upon its arrival at sea.

46 CFR 28.370 - Wiring methods and materials.

Code of Federal Regulations, 2014 CFR

2014-10-01

... that affects one cable does not affect the other. (d) Cable and wire for power and lighting circuits... Operate With More Than 16 Individuals on Board § 28.370 Wiring methods and materials. (a) All cable and... circuit. (b) Each conductor must be No. 22 AWG or larger. Conductors in power and lighting circuits must...

46 CFR 28.370 - Wiring methods and materials.

Code of Federal Regulations, 2012 CFR

2012-10-01

... that affects one cable does not affect the other. (d) Cable and wire for power and lighting circuits... Operate With More Than 16 Individuals on Board § 28.370 Wiring methods and materials. (a) All cable and... circuit. (b) Each conductor must be No. 22 AWG or larger. Conductors in power and lighting circuits must...

46 CFR 28.370 - Wiring methods and materials.

Code of Federal Regulations, 2013 CFR

2013-10-01

... that affects one cable does not affect the other. (d) Cable and wire for power and lighting circuits... Operate With More Than 16 Individuals on Board § 28.370 Wiring methods and materials. (a) All cable and... circuit. (b) Each conductor must be No. 22 AWG or larger. Conductors in power and lighting circuits must...

The Impact of Emotional and Material Social Support on Women's Drug Treatment Completion

ERIC Educational Resources Information Center

Lewandowski, Cathleen A.; Hill, Twyla J.

2009-01-01

This study assessed how women's perceptions of emotional and material social support affect their completion of residential drug treatment. Although previous research has examined how social support affects recovery, few studies, if any, have examined both the types and the sources of social support. The study hypothesized that women's perceptions…

46 CFR 54.05-16 - Production toughness testing.

Code of Federal Regulations, 2011 CFR

2011-10-01

... tests, the V-notch is to be centered between the fusion lines. For the heat affected zone tests, the... material shall be taken from one of the heats of material used in the vessel, and both the electrodes and... successive tests between the weld metal and heat affected zone. Thus, approximately half of all weld...

46 CFR 54.05-16 - Production toughness testing.

Code of Federal Regulations, 2013 CFR

2013-10-01

... tests, the V-notch is to be centered between the fusion lines. For the heat affected zone tests, the... material shall be taken from one of the heats of material used in the vessel, and both the electrodes and... successive tests between the weld metal and heat affected zone. Thus, approximately half of all weld...

46 CFR 54.05-16 - Production toughness testing.

Code of Federal Regulations, 2012 CFR

2012-10-01

... tests, the V-notch is to be centered between the fusion lines. For the heat affected zone tests, the... material shall be taken from one of the heats of material used in the vessel, and both the electrodes and... successive tests between the weld metal and heat affected zone. Thus, approximately half of all weld...

46 CFR 54.05-16 - Production toughness testing.

Code of Federal Regulations, 2014 CFR

2014-10-01

... tests, the V-notch is to be centered between the fusion lines. For the heat affected zone tests, the... material shall be taken from one of the heats of material used in the vessel, and both the electrodes and... successive tests between the weld metal and heat affected zone. Thus, approximately half of all weld...

Material Culture of Multilingualism and Affectivity

ERIC Educational Resources Information Center

Aronin, Larissa

2012-01-01

Affectivity is an important dimension in humans' social and individual lives. It is either a stimulating or hindering aspect of language learning. This article aims to draw attention to material culture as a powerful, but mostly neglected source of data on the use and acquisition of languages, and demonstrates the close and intricate links between…

Arousal Rather than Basic Emotions Influence Long-Term Recognition Memory in Humans

PubMed Central

Marchewka, Artur; Wypych, Marek; Moslehi, Abnoos; Riegel, Monika; Michałowski, Jarosław M.; Jednoróg, Katarzyna

2016-01-01

Emotion can influence various cognitive processes, however its impact on memory has been traditionally studied over relatively short retention periods and in line with dimensional models of affect. The present study aimed to investigate emotional effects on long-term recognition memory according to a combined framework of affective dimensions and basic emotions. Images selected from the Nencki Affective Picture System were rated on the scale of affective dimensions and basic emotions. After 6 months, subjects took part in a surprise recognition test during an fMRI session. The more negative the pictures the better they were remembered, but also the more false recognitions they provoked. Similar effects were found for the arousal dimension. Recognition success was greater for pictures with lower intensity of happiness and with higher intensity of surprise, sadness, fear, and disgust. Consecutive fMRI analyses showed a significant activation for remembered (recognized) vs. forgotten (not recognized) images in anterior cingulate and bilateral anterior insula as well as in bilateral caudate nuclei and right thalamus. Further, arousal was found to be the only subjective rating significantly modulating brain activation. Higher subjective arousal evoked higher activation associated with memory recognition in the right caudate and the left cingulate gyrus. Notably, no significant modulation was observed for other subjective ratings, including basic emotion intensities. These results emphasize the crucial role of arousal for long-term recognition memory and support the hypothesis that the memorized material, over time, becomes stored in a distributed cortical network including the core salience network and basal ganglia. PMID:27818626

Arousal Rather than Basic Emotions Influence Long-Term Recognition Memory in Humans.

PubMed

Marchewka, Artur; Wypych, Marek; Moslehi, Abnoos; Riegel, Monika; Michałowski, Jarosław M; Jednoróg, Katarzyna

2016-01-01

Emotion can influence various cognitive processes, however its impact on memory has been traditionally studied over relatively short retention periods and in line with dimensional models of affect. The present study aimed to investigate emotional effects on long-term recognition memory according to a combined framework of affective dimensions and basic emotions. Images selected from the Nencki Affective Picture System were rated on the scale of affective dimensions and basic emotions. After 6 months, subjects took part in a surprise recognition test during an fMRI session. The more negative the pictures the better they were remembered, but also the more false recognitions they provoked. Similar effects were found for the arousal dimension. Recognition success was greater for pictures with lower intensity of happiness and with higher intensity of surprise, sadness, fear, and disgust. Consecutive fMRI analyses showed a significant activation for remembered (recognized) vs. forgotten (not recognized) images in anterior cingulate and bilateral anterior insula as well as in bilateral caudate nuclei and right thalamus. Further, arousal was found to be the only subjective rating significantly modulating brain activation. Higher subjective arousal evoked higher activation associated with memory recognition in the right caudate and the left cingulate gyrus. Notably, no significant modulation was observed for other subjective ratings, including basic emotion intensities. These results emphasize the crucial role of arousal for long-term recognition memory and support the hypothesis that the memorized material, over time, becomes stored in a distributed cortical network including the core salience network and basal ganglia.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ding, R.; Rudakov, D. L.; Stangeby, P. C.

Dedicated DIII-D experiments coupled with modeling reveal that the net erosion rate of high-Z materials, i.e. Mo and W, is strongly affected by carbon concentration in the plasma and the magnetic pre-sheath properties. We have investigated different methods such as electrical biasing and local gas injection to control high-Z material erosion. The net erosion rate of high-Z materials is significantly reduced due to the high local re-deposition ratio. The ERO modeling shows that the local re-deposition ratio is mainly controlled by the electric field and plasma density within the magnetic pre-sheath. The net erosion can be significantly suppressed by reducingmore » the sheath potential drop. A high carbon impurity concentration in the background plasma is also found to reduce the net erosion rate of high-Z materials. Both DIII-D experiments and modeling show that local 13CH 4 injection can create a carbon coating on the metal surface. The profile of 13C deposition provides quantitative information on radial transport due to E × B drift and the cross-field diffusion. The deuterium gas injection upstream of the W sample can reduce W net erosion rate by plasma perturbation. The inter-ELM W erosion we measured in H-mode plasmas, rates at different radial locations are well reproduced by ERO modeling taking into account charge-state-resolved carbon ion flux in the background plasma calculated using the OEDGE code.« less

Use of simulated experiments for material characterization of brittle materials subjected to high strain rate dynamic tension

PubMed Central

Saletti, Dominique

2017-01-01

Rapid progress in ultra-high-speed imaging has allowed material properties to be studied at high strain rates by applying full-field measurements and inverse identification methods. Nevertheless, the sensitivity of these techniques still requires a better understanding, since various extrinsic factors present during an actual experiment make it difficult to separate different sources of errors that can significantly affect the quality of the identified results. This study presents a methodology using simulated experiments to investigate the accuracy of the so-called spalling technique (used to study tensile properties of concrete subjected to high strain rates) by numerically simulating the entire identification process. The experimental technique uses the virtual fields method and the grid method. The methodology consists of reproducing the recording process of an ultra-high-speed camera by generating sequences of synthetically deformed images of a sample surface, which are then analysed using the standard tools. The investigation of the uncertainty of the identified parameters, such as Young's modulus along with the stress–strain constitutive response, is addressed by introducing the most significant user-dependent parameters (i.e. acquisition speed, camera dynamic range, grid sampling, blurring), proving that the used technique can be an effective tool for error investigation. This article is part of the themed issue ‘Experimental testing and modelling of brittle materials at high strain rates’. PMID:27956505

Quantitative assessment of the enamel machinability in tooth preparation with dental diamond burs.

PubMed

Song, Xiao-Fei; Jin, Chen-Xin; Yin, Ling

2015-01-01

Enamel cutting using dental handpieces is a critical process in tooth preparation for dental restorations and treatment but the machinability of enamel is poorly understood. This paper reports on the first quantitative assessment of the enamel machinability using computer-assisted numerical control, high-speed data acquisition, and force sensing systems. The enamel machinability in terms of cutting forces, force ratio, cutting torque, cutting speed and specific cutting energy were characterized in relation to enamel surface orientation, specific material removal rate and diamond bur grit size. The results show that enamel surface orientation, specific material removal rate and diamond bur grit size critically affected the enamel cutting capability. Cutting buccal/lingual surfaces resulted in significantly higher tangential and normal forces, torques and specific energy (p<0.05) but lower cutting speeds than occlusal surfaces (p<0.05). Increasing material removal rate for high cutting efficiencies using coarse burs yielded remarkable rises in cutting forces and torque (p<0.05) but significant reductions in cutting speed and specific cutting energy (p<0.05). In particular, great variations in cutting forces, torques and specific energy were observed at the specific material removal rate of 3mm(3)/min/mm using coarse burs, indicating the cutting limit. This work provides fundamental data and the scientific understanding of the enamel machinability for clinical dental practice. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of G-Coat Plus on the mechanical properties of glass-ionomer cements.

PubMed

Bagheri, R; Taha, N A; Azar, M R; Burrow, M F

2013-12-01

Although various mechanical properties of tooth-coloured materials have been described, little data have been published on the effect of ageing and G-Coat Plus on the hardness and strength of the glass-ionomer cements (GICs). Specimens were prepared from one polyacid-modified resin composite (PAMRC; Freedom, SDI), one resin-modified glass-ionomer cement; (RM-GIC; Fuji II LC, GC), and one conventional glass-ionomer cement; (GIC; Fuji IX, GC). GIC and RM-GIC were tested both with and without applying G-Coat Plus (GC). Specimens were conditioned in 37 °C distilled water for either 24 hours, four and eight weeks. Half the specimens were subjected to a shear punch test using a universal testing machine; the remaining half was subjected to Vickers Hardness test. Data analysis showed that the hardness and shear punch values were material dependent. The hardness and shear punch of the PAMRC was the highest and GIC the lowest. Applying the G-Coat Plus was associated with a significant decrease in the hardness of the materials but increase in the shear punch strength after four and eight weeks. The mechanical properties of the restorative materials were affected by applying G-Coat Plus and distilled water immersion over time. The PAMRC was significantly stronger and harder than the RM-GIC or GIC. © 2013 Australian Dental Association.

Influence of in-shoe heel lifts on plantar pressure and center of pressure in the medial-lateral direction during walking.

PubMed

Zhang, Xianyi; Li, Bo

2014-04-01

The aim of this study was to investigate how the height and material of in-shoe heel lifts affect plantar pressure and center of pressure (COP) trajectory in the medial-lateral direction during walking. Seventeen healthy young male adults were asked to walk along an 8m walkway while wearing a high-cut flat shoe and 5 different heel lifts. Peak pressure (PP), pressure-time integral (PTI) and contact area (CA) were measured by Pedar insole system for three foot regions: forefoot, midfoot and heel. Range and velocity of medial-lateral (ML) COP during forefoot contact phase (FFCP) and foot flat phase (FFP) were collected using Footscan pressure plate. Forefoot pressure and ML-COP parameters increased as the heel was elevated. Statistically significant attenuation of heel peak plantar pressure was provided by all heel lifts except for the hard lift. Post hoc tests suggest that material had a greater influence on the range and velocity of ML-COP during FFCP than heel height, while during FFP, heel height seemed to affect these parameters more. The findings from this study suggest that thick heel lifts should be used with caution, and that a heel lift made of materials with good support and elastic properties might be more appropriate to improve footwear comfort and medial-lateral motion control. Copyright © 2013 Elsevier B.V. All rights reserved.

Hierarchical thermoelectrics: crystal grain boundaries as scalable phonon scatterers

NASA Astrophysics Data System (ADS)

Selli, Daniele; Boulfelfel, Salah Eddine; Schapotschnikow, Philipp; Donadio, Davide; Leoni, Stefano

2016-02-01

Thermoelectric materials are strategically valuable for sustainable development, as they allow for the generation of electrical energy from wasted heat. In recent years several strategies have demonstrated some efficiency in improving thermoelectric properties. Dopants affect carrier concentration, while thermal conductivity can be influenced by alloying and nanostructuring. Features at the nanoscale positively contribute to scattering phonons, however those with long mean free paths remain difficult to alter. Here we use the concept of hierarchical nano-grains to demonstrate thermal conductivity reduction in rocksalt lead chalcogenides. We demonstrate that grains can be obtained by taking advantage of the reconstructions along the phase transition path that connects the rocksalt structure to its high-pressure form. Since grain features naturally change as a function of size, they impact thermal conductivity over different length scales. To understand this effect we use a combination of advanced molecular dynamics techniques to engineer grains and to evaluate thermal conductivity in PbSe. By affecting grain morphologies only, i.e. at constant chemistry, two distinct effects emerge: the lattice thermal conductivity is significantly lowered with respect to the perfect crystal, and its temperature dependence is markedly suppressed. This is due to an increased scattering of low-frequency phonons by grain boundaries over different size scales. Along this line we propose a viable process to produce hierarchical thermoelectric materials by applying pressure via a mechanical load or a shockwave as a novel paradigm for material design.

Drop-off detection with the long cane: effect of cane shaft weight and rigidity on performance

PubMed Central

Kim, Dae Shik; Emerson, Robert Wall; Naghshineh, Koorosh; Auer, Alexander

2016-01-01

Most travellers who are blind rely on a long cane to detect drop-offs on their walking paths. We examined how different cane shaft materials affect drop-off detection performance through providing different vibrotactile and proprioceptive feedbacks to the cane user. Results of the study showed a significant interaction between cane shaft weight and how the cane is used. A heavier cane was advantageous for detecting drop-offs when the individual used the ‘constant contact technique’ – cane tip stays in contact with the walking surface at all times – but not when he used the ‘two-point touch technique’ – cane tip is rhythmically tapped on the surface. In addition, a more flexible cane was advantageous for detecting drop-offs when the two-point touch technique was used but not when the constant contact technique was used. It is recommended that, when blind individuals select a cane shaft material, they consider which long cane technique they use more often. Practitioner Summary: Long cane shaft material affects how well a blind individual can detect drop-offs. A heavier shaft was advantageous when using the constant contact technique (cane tip stays in continuous contact with the surface), while a more flexible shaft was better when using the two-point touch technique (cane tip rhythmically taps the surface). PMID:27065052

The use of refused tea as litter material for broiler chickens.

PubMed

Atapattu, N S B M; Wickramasinghe, K P

2007-05-01

A completely randomized design experiment was conducted to determine the suitability of refused tea (RT) as a litter material for broiler chickens. Physiochemical properties of RT were compared with paddy husk (PH). Subsequently, broilers were raised on RT- or PH-based litter to compare the performances and litter qualities. Twenty-day-old broiler chicks (n = 150) were randomly allocated into 6 deep litter pens so that each treatment had 3 replicates. Chicks received 0.8 ft(2) of floor spacing until d 28 and 1.3 ft(2) thereafter. Each cage had a feeder and a drinker. Litter materials and litter samples taken on 28, 35, and 39 d were analyzed for bulk density, moisture, ash, and N. Chick mortality was low (1.3%) and similar on 2 types of litters. Live weights on d 28, 35, 39, and weight gains, feed intakes, dressing percentages, and feed conversion ratios were not affected by the type of litter material. The bulk density, moisture level, and pH of the RT were comparable with PH. Even though the water-holding capacity of PH (213%) was significantly higher (P < 0.01) than RT (70%), the latter material had significantly higher (P < 0.01) water-releasing capacity compared with the former (17.9 vs. 13.6%). Throughout the experiment the RT litter had around 10% units higher moisture level than PH litter. By d 39, the moisture content of the RT litter was (48%) significantly higher (P = 0.05) than PH litter (37%). The N contents of RT litter were higher (P < 0.05) than those of PH on d 28, 35, and 39, being 8.1, 7.8, and 7% and 3.4, 3.6, and 3%, respectively. It was concluded that RT could be successfully used as an alternative litter material for broilers. A higher N content in RT-based spent broiler litter would make it be a better organic fertilizer and ruminant feed compared with PH-based litter.

A One-Year Evaluation of a Free Fissure Sealant Program

PubMed Central

M, Bakhtiar; N, Azadi; A, Golkari

2016-01-01

Statement of Problem: Pit and fissure sealant therapy has been approved as an effective measure in the prevention of occlusal dental caries. Resin based materials are the most common materials used worldwide. A variety of resin based fissure sealants are produced and used. Most of them have been presented with ideal results in research environment. However, their effectiveness in the real life, especially in a mass application program such as Iran’s oral health reform plan is not clear. Objectives: To evaluate the longevity of different fissure sealant applied in Iran’s oral health reform plan in Fars Province (south of Iran) after one year. Materials and Methods: Seven counties were selected. One hundred 6- to 8-year-old school children who had undergone fissure sealant therapy in spring 2015 were randomly selected from each county. Their first molars were examined to evaluate the status of the fissure sealants which were applied one year ago. Data on the type/brand of fissure sealant materials, type and experience of clinicians who applied them, existence of a chair-side assistant, and whether the children were caries-free at the time of fissure sealant application were collected from the existing reports. Results: Data of 1974 teeth from 598 children were used for the final analysis. The effects of type/brand of the material was significant on the final results and remained significant (p < 0.001) after adjustments for the level of fluoride, urban/rural area, upper/lower jaw, type of clinician who applied the sealant, existence of a chair-side assistant, and child’s gender, age, and being caries-free. Conclusions: Many factors affect the success rate of a fissure sealant therapy program. The type/brand of the material remained significantly related to the success rate of the fissure sealant even after adjustments for other influencing factors. In this study, ClinproTM Sealant (3M/ESPE, USA) showed better longevity after one year of application. PMID:28959758

Feeling cybervictims' pain-The effect of empathy training on cyberbullying.

PubMed

Schultze-Krumbholz, Anja; Schultze, Martin; Zagorscak, Pavle; Wölfer, Ralf; Scheithauer, Herbert

2016-01-01

As the world's population increasingly relies on the use of modern technology, cyberbullying becomes an omnipresent risk for children and adolescents and demands counteraction to prevent negative (online) experiences. The classroom-based German preventive intervention "Medienhelden" (engl.: "Media Heroes") builds on previous knowledge about links between cognitive empathy, affective empathy, and cyberbullying, among others. For an evaluation study, longitudinal data were available from 722 high school students aged 11-17 years (M = 13.36, SD = 1.00, 51.8% female) before and six months after the implementation of the program. A 10-week version and a 1-day version were conducted and compared with a control group (controlled pre-long-term-follow-up study). Schools were asked to randomly assign their participating classes to the intervention conditions. Multi-group structural equation modeling (SEM) showed a significant effect of the short intervention on cognitive empathy and significant effects of the long intervention on affective empathy and cyberbullying reduction. The results suggest the long-term intervention to be more effective in reducing cyberbullying and promoting affective empathy. Without any intervention, cyberbullying increased and affective empathy decreased across the study period. Empathy change was not generally directly linked to change in cyberbullying behavior. "Media Heroes" provides effective teaching materials and empowers schools to address the important topic of cyberbullying in classroom settings without costly support from the outside. © 2016 Wiley Periodicals, Inc.

Pb and Cd binding to natural freshwater biofilms developed at different pH: the important role of culture pH.

PubMed

Hua, Xiuyi; Dong, Deming; Ding, Xiaoou; Yang, Fan; Jiang, Xu; Guo, Zhiyong

2013-01-01

The effects of solution pH on adsorption of trace metals to different types of natural aquatic solid materials have been studied extensively, but few studies have been carried out to investigate the effect of pH at which the solid materials were formed on the adsorption. The purpose of present study is to examine this effect of culture pH on metal adsorption to natural freshwater biofilms. The adsorption of Pb and Cd to biofilms which were developed at different culture pH values (ranging from 6.5 to 9.0) was measured at the same adsorption pH value (6.5). The culture pH had considerable effects on both composition and metal adsorption ability of the biofilms. Higher culture pH usually promoted the accumulation of organic material and Fe oxides in the biofilms. The culture pH also affected the quantity and species of algae in the biofilms. The adsorption of Pb and Cd to the biofilms generally increased with the increase of culture pH. This increase was minor at lower pH range and significant at higher pH range and was more remarkable for Cd adsorption than for Pb adsorption. The notable contribution of organic material to the adsorption at higher culture pH values was also observed. The profound impacts of culture pH on adsorption behavior of biofilms mainly resulted from the variation of total contents of the biofilm components and were also affected by the alteration of composition and properties of the components.

Residual Gases in Crystal Growth Systems: Their Origin, Magnitude, and Dependence on the Processing Conditions

NASA Technical Reports Server (NTRS)

Palosz, W.

2003-01-01

Residual gases present in closed ampoules may affect different crystal growth processes. Their presence may affect techniques requiring low pressures and affect the crystal quality in different ways. For that reason a good understanding and control of formation of residual gases may be important for an optimum design and meaningful interpretation of crystal growth experiments. Our extensive experimental and theoretical study includes degassing of silica glass and generation of gases from various source materials. Different materials processing conditions, like outgassing under vacuum, annealing in hydrogen, resublimation, different material preparation procedures, multiple annealings, different processing times, and others were applied and their effect on the amount and composition of gas were analyzed. The experimental results were interpreted based on theoretical calculations on diffusion in silica glass and source materials and thermochemistry of the system. Procedures for a reduction of the amount of gas are also discussed.

Full-Field Strain Measurement On Titanium Welds And Local Elasto-Plastic Identification With The Virtual Fields Method

NASA Astrophysics Data System (ADS)

Tattoli, F.; Pierron, F.; Rotinat, R.; Casavola, C.; Pappalettere, C.

2011-01-01

One of the main problems in welding is the microstructural transformation within the area affected by the thermal history. The resulting heterogeneous microstructure within the weld nugget and the heat affected zones is often associated with changes in local material properties. The present work deals with the identification of material parameters governing the elasto—plastic behaviour of the fused and heat affected zones as well as the base material for titanium hybrid welded joints (Ti6Al4V alloy). The material parameters are identified from heterogeneous strain fields with the Virtual Fields Method. This method is based on a relevant use of the principle of virtual work and it has been shown to be useful and much less time consuming than classical finite element model updating approaches applied to similar problems. The paper will present results and discuss the problem of selection of the weld zones for the identification.

Microgravity

NASA Image and Video Library

1997-11-01

The purpose of the experiments for the Advanced Automated Directional Solidification Furnace (AADSF) is to determine how gravity-driven convection affects the composition and properties of alloys (mixtures of two or more materials, usually metal). During the USMP-4 mission, the AADSF will solidify crystals of lead tin telluride and mercury cadmium telluride, alloys of compound semiconductor materials used to make infrared detectors and lasers, as experiment samples. Although these materials are used for the same type application their properties and compositional uniformity are affected differently during the solidification process.

Three-Dimensional Stress Fields and Slip Systems for Single Crystal Superalloy Notched Specimens

NASA Technical Reports Server (NTRS)

Magnan, Shannon M.; Throckmorton, David (Technical Monitor)

2002-01-01

Single crystal superalloys have become increasingly popular for turbine blade and vane applications due to their high strength, and creep and fatigue resistance at elevated temperatures. The crystallographic orientation of a single crystal material greatly affects its material properties, including elastic modulus, shear modulus, and ductility. These directional properties, along with the type of loading and temperature, dictate an anisotropic response in the yield strength, creep resistance, creep rupture ductility, fatigue resistance, etc. A significant amount of research has been conducted to determine the material properties in the <001> orientation, yet the material properties deviating from the <001> orientation have not been assessed for all cases. Based on the desired application and design criteria, a crystal orientation is selected to yield the maximum properties. Currently, single crystal manufacturing is able to control the primary crystallographic orientation within 15 of the target orientation, which is an acceptable deviation to meet both performance and cost guidelines; the secondary orientation is rarely specified. A common experiment is the standard load-controlled tensile test, in which specimens with different orientations can be loaded to observe the material response. The deformation behavior of single-crystal materials under tension and compression is known to be a function of not only material orientation, but also of varying microdeformation (i.e. dislocation) mechanisms. The underlying dislocation motion causes deformation via slip, and affects the activation of specific slip systems based on load and orientation. The slip can be analyzed by observing the visible traces left on the surface of the specimen from the slip activity within the single crystal material. The goal of this thesis was to predict the slip systems activated in three-dimensional stress fields of a notched tensile specimen, as a function of crystal orientation, using finite element analysis without addressing microstructural deformation mechanisms that govern their activation. Out of three orientations tested, the specimen with a [110] load orientation and a [001] growth direction had the lowest maximum resolved shear stress; this specimen orientation appears to be the best design candidate for a tensile application.

Influence of compact disk recording protocols on reliability and comparability of speech audiometry outcomes: acoustic analysis.

PubMed

Di Berardino, F; Tognola, G; Paglialonga, A; Alpini, D; Grandori, F; Cesarani, A

2010-08-01

To assess whether different compact disk recording protocols, used to prepare speech test material, affect the reliability and comparability of speech audiometry testing. We conducted acoustic analysis of compact disks used in clinical practice, to determine whether speech material had been recorded using similar procedures. To assess the impact of different recording procedures on speech test outcomes, normal hearing subjects were tested using differently prepared compact disks, and their psychometric curves compared. Acoustic analysis revealed that speech material had been recorded using different protocols. The major difference was the gain between the levels at which the speech material and the calibration signal had been recorded. Although correct calibration of the audiometer was performed for each compact disk before testing, speech recognition thresholds and maximum intelligibility thresholds differed significantly between compact disks (p < 0.05), and were influenced by the gain between the recording level of the speech material and the calibration signal. To ensure the reliability and comparability of speech test outcomes obtained using different compact disks, it is recommended to check for possible differences in the recording gains used to prepare the compact disks, and then to compensate for any differences before testing.

Loss of effectiveness of protective clothing after its use in pesticide sprays and its multiple washes.

PubMed

Espanhol-Soares, Melina; Teodoro de Oliveira, Manuela; Machado-Neto, Joaquim Gonçalves

2017-02-01

Protective clothing is used as a barrier against pesticides when working with agricultural sprays. The aim of this study was to evaluate the pesticide penetration, retention, and repellence of the material and seams of a whole-body protective garment used by applicators of pesticides. The efficiency of the material and seams of the whole-body garment were determined for its classification as proposed by ISO 27065 (ISO, 2011). The evaluation method used was the pipette test of ISO 22608. The efficiency of the material and seams of the garment (100% cotton) were tested by contamination with formulations of Roundup Original® SL; Nufos EC® and Supera SC®. The presence of the seams in the protective clothing reduced its efficiency in the control of dermal exposure, except when protecting against the Supera SC® formulation. The number of washes and uses affected the efficiency of the material and seams of the garment. The type of formulation interfered significantly in the penetration of pesticides into the material and seams. Thus, the laboratory efficiency assessment of protective clothing is necessary to determine what types of formulations and use conditions are appropriate for workers.

Effect of long-term exposure to Low Earth Orbit (LEO) space environment

NASA Technical Reports Server (NTRS)

Zimcik, D. G.

1987-01-01

Data obtained from components and materials from the Solar Maximum Mission satellite are presented and compared to data for similar materials obtained from the Advanced Composite Materials Exposure to Space Experiment (ACOMEX) flown on Shuttle mission STS-41G. In addition to evaluation of surface erosion and mass loss that may be of importance to very long-term missions, comparisons of solar absorptance and thermal emittance measurements for both long and short term exposures were made. Although the ratio of absorptance over emittance can be altered by proper choice of materials to ensure a proper operating environment for the spacecraft, once the thermal design is established, it is important that the material properties not change in order to maintain the operating environment for many payload and bus items such as electronics, batteries, fuel, etc. However, data presented show significant changes after short exposure in low Earth environment. Moreover, the measured changes are shown to differ according to the manner of exposure, i.e., normal or oblique, which also affects the resultant eroded surface morphology. These results identify constraints to be considered in development of flight experiments or laboratory testing.

The Use of Restorative Materials in Primary Molars among Pediatric Dentists in Israel.

PubMed

Blumer, Sigalit; Peretz, Benjamin; Ratson, Tal

To assess the current choice of various restoration materials among Israeli pediatric dentists according to seniority and specialty. Participating dentists completed a 23-item questionnaire on their qualifications, type of practice and preference of restorative material. Seventy-five dentists (average age 46.27±12.6 years, 58 females) participated. Forty-one were specialist pediatric dentists and 34 were general practitioners. Amalgam was preferred by 49.3%, followed by composite (41.3%), glass ionomer cement (5.3%) and compomer (4%). Only 13.3% of the dentists thought amalgam bears environmental and health hazards, compared to 49.3% for composite. Satisfaction was high for amalgam and composite, less for glass ionomer cements and least for compomer. General practitioners preferred amalgam (70.6%) while pediatric dentists preferred composite (51.2%), P < 0.003. Amalgam and composite were the materials of choice among the participating Israeli dentists. Most of them (86.7%) responded that amalgam does not possess any health issues. Their satisfaction with the restoration materials was highest for amalgam and composite, a choice significantly affected by whether they were in general practice (amalgam) or specialized in pediatric dentistry (composite).

Viscoelastic properties of orthodontic adhesives used for lingual fixed retainer bonding.

PubMed

Papadogiannis, D; Iliadi, A; Bradley, T G; Silikas, N; Eliades, G; Eliades, T

2017-01-01

To evaluate the viscoelastic properties of two experimental BPA-free and one BisGMA-based orthodontic resin composite adhesives for bonding fixed retainers. A commercially available BisGMA-based (TXA: Transbond LR) and two bisphenol A-free experimental adhesives (EXA and EXB) were included in the study. The viscoelastic behavior of the adhesives was evaluated under static and dynamic conditions at dry and wet states and at various temperatures (21, 37, 50°C). The parameters determined were shear modulus (G), Young's modulus (E) under static testing and storage modulus (G 1 ), loss tangent (tanδ) and dynamic viscosity (n*) under dynamic testing. Statistical analysis was performed by 2-way ANOVA and Bonferroni post-hoc tests (α=0.05). For static testing, a significant difference was found within material and storage condition variables and a significant interaction between the two independent variables (p<0.001 for G and E). EXA demonstrated the highest G and E values at 21°C/dry group. Dry specimens showed the highest G and E values, but with no significant difference from 21°C/wet specimens, except EXA in G. Wet storage at higher temperatures (37°C and 50°C) adversely affected all the materials to a degree ranging from 40 to 60% (p<0.001). For dynamic testing, a significant difference was also found in material and testing condition groups, with a significant interaction between the two independent variables (p<0.001 for G 1 and n*, p<0.01 for tanδ). Reduction in G 1 , and n* values, and increase in tanδ values were encountered at increased water temperatures. The apparent detrimental effect of high temperature on the reduction of properties of adhesives may contribute to the loss of stiffness of the fixed retainer configuration under ordinary clinical conditions with unfavorable effects on tooth position and stability of the orthodontic treatment result. Copyright © 2016 The Academy of Dental Materials. All rights reserved.

Environmental Regulations as Drivers of Materials Obsolescence

NASA Technical Reports Server (NTRS)

Scroggins, Sharon

2010-01-01

This slide presentation reviews the operations of the Principal Center for Regulatory Risk Analysis and Communication (RRAC-PC) and the impact of environmental regulations in making some materials obsolete. The center is NASA's resource for identifying and managing risks associated with changing environmental regulations. To this end the center acts as an regulatory early warning system, to review track and analyze emerging regulations, collaborate with the technical community on regulatory risk analysis and interpretation and to represent NASA's interests to the regulatory agencies. Regulations frequently result in making some materials unavailable forcing a change to another material. Processes may also be changed due to environmental regulations. For example some items that were sprayed with a chemical may now have to be painted or dipped with the chemical. Sometimes a regulation changes the use of a certain product, which does not affect the usage on Earth, but has significant implications in space. An example of this is the use of lead-free solders of basically tin, which don't appear to have any problem on Earth, but in space applications tin whiskers have resulted in several confirmed satellite failures.

Construction cost impacts related to manpower, material, and equipment factors in contractor firms perspective

NASA Astrophysics Data System (ADS)

Husin, Saiful; Abdullah, Riza, Medyan; Afifuddin, Mochammad

2017-11-01

Risk can be defined as consequences which possible happened inscrutably. Although an activity has planned as good as possible, but it keep contains uncertainty. Implementation of construction project was encountering various risk impacts from a number of risk factors. This study was intended to analyze the impacts of construction cost to for contractor firms as construction project executor related to the factors of manpower, material and equipment. The study was using data obtained from questionnaires distributed to 15 large qualification contractor firms. The period of study classified into conflict period (2000-2004), post tsunami disaster rehabilitation and reconstruction period (2005-2009), and post rehabilitation and reconstruction period (2010-present). The statistical analysis of severity index and variance used to analyze the data. The three risk factors reviewed generally affected the cost in a medium impact. The high impact occurred in minor variables, which are `increase in material prices', `theft of materials', and `the fuel scarcity'. In overall, the three risk factors and the observed period contributed significant impact on construction costs.

Thermal engineering of FAPbI3 perovskite material via radiative thermal annealing and in situ XRD

PubMed Central

Pool, Vanessa L.; Dou, Benjia; Van Campen, Douglas G.; Klein-Stockert, Talysa R.; Barnes, Frank S.; Shaheen, Sean E.; Ahmad, Md I.; van Hest, Maikel F. A. M.; Toney, Michael F.

2017-01-01

Lead halide perovskites have emerged as successful optoelectronic materials with high photovoltaic power conversion efficiencies and low material cost. However, substantial challenges remain in the scalability, stability and fundamental understanding of the materials. Here we present the application of radiative thermal annealing, an easily scalable processing method for synthesizing formamidinium lead iodide (FAPbI3) perovskite solar absorbers. Devices fabricated from films formed via radiative thermal annealing have equivalent efficiencies to those annealed using a conventional hotplate. By coupling results from in situ X-ray diffraction using a radiative thermal annealing system with device performances, we mapped the processing phase space of FAPbI3 and corresponding device efficiencies. Our map of processing-structure-performance space suggests the commonly used FAPbI3 annealing time, 10 min at 170 °C, can be significantly reduced to 40 s at 170 °C without affecting the photovoltaic performance. The Johnson-Mehl-Avrami model was used to determine the activation energy for decomposition of FAPbI3 into PbI2. PMID:28094249

Comparison of VOC and ammonia emissions from individual PVC materials, adhesives and from complete structures.

PubMed

Järnström, H; Saarela, K; Kalliokoski, P; Pasanen, A-L

2008-04-01

Emission rates of volatile organic compounds (VOCs) and ammonia measured from six PVC materials and four adhesives in the laboratory were compared to the emission rates measured on site from complete structures. Significantly higher specific emission rates (SERs) were generally measured from the complete structures than from individual materials. There were large differences between different PVC materials in their permeability for VOCs originating from the underlying structure. Glycol ethers and esters from adhesives used in the installation contributed to the emissions from the PVC covered structure. Emissions of 2-ethylhexanol and TXIB (2,2,4-trimethyl-1,3-pentanediol diisobutyrate) were common. High ammonia SERs were measured from single adhesives but their contribution to the emissions from the complete structure did not appear as obvious as for VOCs. The results indicate that three factors affected the VOC emissions from the PVC flooring on a structure: 1) the permeability of the PVC product for VOCs, 2) the VOC emission from the adhesive used, and 3) the VOC emission from the backside of the PVC product.

Foreign Object Damage in a Gas-Turbine Grade Silicon Nitride by Spherical Projectiles of Various Materials

NASA Technical Reports Server (NTRS)

Choi, Sung R.; Racz, Zsolt; Bhatt, Ramakrishna T.; Brewer, David N.

2006-01-01

Assessments of foreign object damage (FOD) of a commercial, gas-turbine grade, in situ toughened silicon nitride ceramic (AS800, Honeywell Ceramics Components) were made using four different projectile materials at ambient temperature. AS800 flexure target specimens rigidly supported were impacted at their centers in a velocity range from 50 to 450 m/s by spherical projectiles with a diameter of 1.59 mm. Four different projectile materials were used including hardened steel, annealed steel, silicon nitride ceramic, and brass. Post-impact strength of each target specimen impacted was determined as a function of impact velocity to appraise the severity of local impact damage. For a given impact velocity, the degree of strength degradation was greatest for ceramic balls, least for brass balls, and intermediate for annealed and hardened steel balls. For steel balls, hardened projectiles yielded more significant impact damage than annealed counterparts. The most important material parameter affecting FOD was identified as hardness of projectiles. Impact load as a function of impact velocity was quasi-statically estimated based on both impact and static indentation associated data.

Thermal engineering of FAPbI 3 perovskite material via radiative thermal annealing and in situ XRD

DOE PAGES

Pool, Vanessa L.; Dou, Benjia; Van Campen, Douglas G.; ...

2017-01-17

Lead halide perovskites have emerged as successful optoelectronic materials with high photovoltaic power conversion efficiencies and low material cost. However, substantial challenges remain in the scalability, stability and fundamental understanding of the materials. Here we present the application of radiative thermal annealing, an easily scalable processing method for synthesizing formamidinium lead iodide (FAPbI 3) perovskite solar absorbers. Devices fabricated from films formed via radiative thermal annealing have equivalent efficiencies to those annealed using a conventional hotplate. By coupling results from in situ X-ray diffraction using a radiative thermal annealing system with device performances, we mapped the processing phase space ofmore » FAPbI 3 and corresponding device efficiencies. Our map of processing-structure-performance space suggests the commonly used FAPbI 3 annealing time, 10 min at 170 degrees C, can be significantly reduced to 40 s at 170 degrees C without affecting the photovoltaic performance. Lastly, the Johnson-Mehl-Avrami model was used to determine the activation energy for decomposition of FAPbI 3 into PbI 2.« less

A study of the effect of sonication time on the catalytic performance of layered WS2 from various sources.

PubMed

Leong, Shi Xuan; Mayorga-Martinez, Carmen C; Sofer, Zdeněk; Luxa, Jan; Tan, Shu Min; Pumera, Martin

2017-01-25

WS 2 is a transition metal dichalcogenide (TMD) with many potential applications from catalysis to sensing, and is of interest both in its bulk and monolayer forms. There is discrepancy in the literature on the reported electrocatalytic effect of layered WS 2 . In this study, we examine two issues: the influence of the WS 2 source and the effect of a common agitation technique via ultrasonication on the observed electrocatalysis. Bulk WS 2 from five different chemical providers demonstrated different HER electrocatalytic performances. Changes to the duration of sonication result in different HER electrocatalytic performances across all WS 2 materials. This may affect the efficiency of subsequent modifications from which these TMD materials serve as precursor materials. On the other hand, while WS 2 materials from different suppliers showed varying HET performances, changes in sonication time have no significant effect on their HET performances. Both the WS 2 source and the duration of sonication have different implications for the electrochemical performance of bulk WS 2 and thus represent important variables to consider in research involving WS 2 .

Material Compatibility with Space Storable Propellants. Design Guidebook

NASA Technical Reports Server (NTRS)

Uney, P. E.; Fester, D. A.

1972-01-01

An important consideration in the design of spacecraft for interplanetary missions is the compatibility of storage materials with the propellants. Serious problems can arise because many propellants are either extremely reactive or subject to catalytic decomposition, making the selection of proper materials of construction for propellant containment and control a critical requirement for the long-life applications. To aid in selecting materials and designing and evaluating various propulsion subsystems, available information on the compatibility of spacecraft materials with propellants of interest was compiled from literature searches and personal contacts. The compatibility of both metals and nonmetals with hydrazine, monomethyl hydrazine, nitrated hydrazine, and diborance fuels and nitrogen tetroxide, fluorine, oxygen difluoride, and Flox oxidizers was surveyed. These fuels and oxidizers encompass the wide variety of problems encountered in propellant storage. As such, they present worst case situations of the propellant affecting the material and the material affecting the propellant. This includes material attack, propellant decomposition, and the formation of clogging materials.

76 FR 72902 - Materials Processing Equipment Technical Advisory Committee;

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-28

... DEPARTMENT OF COMMERCE Bureau of Industry and Security Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting The Materials Processing Equipment Technical... questions that affect the level of export controls applicable to materials processing equipment and related...

77 FR 15592 - Privacy Act; Implementation

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-16

... million or more or adversely affect in a material way the economy; a sector of the economy; productivity... integrity of Federal testing materials; and safeguard evaluation materials used for military promotions when...

76 FR 49659 - Privacy Act; Implementation

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-11

... or more or adversely affect in a material way the economy; a sector of the economy; productivity... testing materials, and to safeguard evaluation materials used for military promotions when furnished by a...

Affective Overload: The Effect of Emotive Visual Stimuli on Target Vocabulary Retrieval.

PubMed

Çetin, Yakup; Griffiths, Carol; Özel, Zeynep Ebrar Yetkiner; Kinay, Hüseyin

2016-04-01

There has been considerable interest in cognitive load in recent years, but the effect of affective load and its relationship to mental functioning has not received as much attention. In order to investigate the effects of affective stimuli on cognitive function as manifest in the ability to remember foreign language vocabulary, two groups of student volunteers (N = 64) aged from 17 to 25 years were shown a Powerpoint presentation of 21 target language words with a picture, audio, and written form for every word. The vocabulary was presented in comfortable rooms with padded chairs and the participants were provided with snacks so that they would be comfortable and relaxed. After the Powerpoint they were exposed to two forms of visual stimuli for 27 min. The different formats contained either visually affective content (sexually suggestive, violent or frightening material) or neutral content (a nature documentary). The group which was exposed to the emotive visual stimuli remembered significantly fewer words than the group which watched the emotively neutral nature documentary. Implications of this finding are discussed and suggestions made for ongoing research.

Ultrasonographic assessment of the equine palmar tendons

PubMed Central

Padaliya, N. R.; Ranpariya, J. J.; Kumar, Dharmendra; Javia, C. B.; Barvalia, D. R.

2015-01-01

Aim: The present study was conducted to evaluate the equine palmar tendon by ultrasonography (USG) in standing the position. Materials and Methods: USG of palmar tendons was performed in 40 adult horses using linear transducer having frequency of 10-18 MHz (e-soate, My Lab FIVE) and L52 linear array transducer (Titan, SonoSite) with frequencies ranging from 8 to 10 MHz. Palmar tendon was divided into 7 levels from distal to accessory carpal bone up to ergot in transverse scanning and 3 levels in longitudinal scanning. Results: The USG evaluation was very useful for diagnosis of affections of the conditions such as chronic bowed tendon, suspensory ligament desmitis, carpal sheath tenosynovitis and digital sheath effusions. The mean cross-sectional area (cm2) of affected tendons was significantly increased in affected than normal tendons. The echogenicity was also found reduced in affected tendons and ligaments along with disorganization of fiber alignment depending on the severity of lesion and injury. Conclusion: USG proved ideal diagnostic tool for diagnosis and post-treatment healing assessment of tendon injuries in horses. PMID:27047074

Spirituality: An Affective Facet for Curriculum Consideration.

ERIC Educational Resources Information Center

Dickmann, Leonore W.

1980-01-01

The current age has been characterized as an Age of Materialism in which personal goals are material aims and pleasures. The need for getting back to a spiritual culture is considered foundational. It is the duty of educators to provide for the spiritual or affective domain of a learner's development. To neglect this aspect of a person's being is…

A three-dimensional thermal finite element analysis of AISI 304 stainless steel and copper dissimilar weldment

NASA Astrophysics Data System (ADS)

Singh, Gurdeep; Saxena, Ravindra K.; Pandey, Sunil

2018-04-01

The aim of this study to developed a 3-D thermal finite element model for dissimilar material welding of AISI-304 stainless steel and copper. Welding of similar material is widely studied using experimental and numerical methods but the problem becomes trivial for the welding of dissimilar materials especially in ferrous and nonferrous materials. Finite element analysis of dissimilar material welding is a cost-effective method for the understanding and analysis of the process. The finite element analysis has been performed to predict the heat affected zone and temperature distribution in AISI-304 stainless steel and copper dissimilar weldment using MSC Marc 2017®. Due to the difference in physical properties of these materials the behavior of heat affected zone and temperature distribution are perceived to be different. To verify the accuracy of the thermal finite element model, the welding process was simulated with butt-welded joints having same dimensions and parameters from Attarha and Far [1]. It is found from the study that the heat affected zone is larger in copper weld pads than in AISI 304 stainless steel due to large difference in thermal conductivity of these two weld pads.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bates, Robert; McConnell, Elizabeth

Machining methods across many industries generally require multiple operations to machine and process advanced materials, features with micron precision, and complex shapes. The resulting multiple machining platforms can significantly affect manufacturing cycle time and the precision of the final parts, with a resultant increase in cost and energy consumption. Ultrafast lasers represent a transformative and disruptive technology that removes material with micron precision and in a single step manufacturing process. Such precision results from athermal ablation without modification or damage to the remaining material which is the key differentiator between ultrafast laser technologies and traditional laser technologies or mechanical processes.more » Athermal ablation without modification or damage to the material eliminates post-processing or multiple manufacturing steps. Combined with the appropriate technology to control the motion of the work piece, ultrafast lasers are excellent candidates to provide breakthrough machining capability for difficult-to-machine materials. At the project onset in early 2012, the project team recognized that substantial effort was necessary to improve the application of ultrafast laser and precise motion control technologies (for micromachining difficult-to-machine materials) to further the aggregate throughput and yield improvements over conventional machining methods. The project described in this report advanced these leading-edge technologies thru the development and verification of two platforms: a hybrid enhanced laser chassis and a multi-application testbed.« less