Effects of lead time of verbal collision warning messages on driving behavior in connected vehicle settings.

PubMed

Wan, Jingyan; Wu, Changxu; Zhang, Yiqi

2016-09-01

Under the connected vehicle environment, vehicles will be able to exchange traffic information with roadway infrastructure and other vehicles. With such information, collision warning systems (CWSs) will be able to warn drivers with potentially hazardous situations within or out of sight and reduce collision accidents. The lead time of warning messages is a crucial factor in determining the effectiveness of CWSs in the prevention of traffic accidents. Accordingly, it is necessary to understand the effects of lead time on driving behaviors and explore the optimal lead time in various collision scenarios. The present driving simulator experiment studied the effects of controlled lead time at 16 levels (predetermined time headway from the subject vehicle to the collision location when the warning message broadcasted to a driver) on driving behaviors in various collision scenarios. Maximum effectiveness of warning messages was achieved when the controlled lead time was within the range of 5s to 8s. Specifically, the controlled lead time ranging from 4s to 8s led to the optimal safety benefit; and the controlled lead time ranging from 5s to 8s led to more gradual braking and shorter reaction time. Furthermore, a trapezoidal distribution of warning effectiveness was found by building a statistic model using curve estimation considering lead time, lifetime driving experience, and driving speed. The results indicated that the controlled lead time significantly affected driver performance. The findings have implications for the design of collision warning systems. Copyright © 2016 Elsevier Ltd and National Safety Council. All rights reserved.

Analysis of cache for streaming tape drive

NASA Technical Reports Server (NTRS)

Chinnaswamy, V.

1993-01-01

A tape subsystem consists of a controller and a tape drive. Tapes are used for backup, data interchange, and software distribution. The backup operation is addressed. During a backup operation, data is read from disk, processed in CPU, and then sent to tape. The processing speeds of a disk subsystem, CPU, and a tape subsystem are likely to be different. A powerful CPU can read data from a fast disk, process it, and supply the data to the tape subsystem at a faster rate than the tape subsystem can handle. On the other hand, a slow disk drive and a slow CPU may not be able to supply data fast enough to keep a tape drive busy all the time. The backup process may supply data to tape drive in bursts. Each burst may be followed by an idle period. Depending on the nature of the file distribution in the disk, the input stream to the tape subsystem may vary significantly during backup. To compensate for these differences and optimize the utilization of a tape subsystem, a cache or buffer is introduced in the tape controller. Most of the tape drives today are streaming tape drives. A streaming tape drive goes into reposition when there is no data from the controller. Once the drive goes into reposition, the controller can receive data, but it cannot supply data to the tape drive until the drive completes its reposition. A controller can also receive data from the host and send data to the tape drive at the same time. The relationship of cache size, host transfer rate, drive transfer rate, reposition, and ramp up times for optimal performance of the tape subsystem are investigated. Formulas developed will also show the advantages of cache watermarks to increase the streaming time of the tape drive, maximum loss due to insufficient cache, tradeoffs between cache and reposition times and the effectiveness of cache on a streaming tape drive due to idle times or interruptions due in host transfers. Several mathematical formulas are developed to predict the performance of the tape drive. Some examples are given illustrating the usefulness of these formulas. Finally, a summary and some conclusions are provided.

Design and experimental study of a novel giant magnetostrictive actuator

NASA Astrophysics Data System (ADS)

Xue, Guangming; Zhang, Peilin; He, Zhongbo; Li, Dongwei; Huang, Yingjie; Xie, Wenqiang

2016-12-01

Giant magnetostrictive actuator has been widely used in precise driving occasions for its excellent performance. However, in driving a switching valve, especially the ball-valve in an electronic controlled injector, the actuator can't exhibit its good performance for limits in output displacement and responding speed. A novel giant magnetostrictive actuator, which can reach its maximum displacement for being exerted with no bias magnetic field, is designed in this paper. Simultaneously, elongating of the giant magetostrictive material is converted to shortening of the actuator's axial dimension with the help of an output rod in "T" type. Furthermore, to save responding time, the driving voltage with high opening voltage while low holding voltage is designed. Responding time and output displacement are studied experimentally with the help of a measuring system. From measured results, designed driving voltage can improve the responding speed of actuator displacement quite effectively. And, giant magnetostrictive actuator can output various steady-state displacements to reach more driving effects.

A rear-end collision risk assessment model based on drivers' collision avoidance process under influences of cell phone use and gender-A driving simulator based study.

PubMed

Li, Xiaomeng; Yan, Xuedong; Wu, Jiawei; Radwan, Essam; Zhang, Yuting

2016-12-01

Driver's collision avoidance performance has a direct link to the collision risk and crash severity. Previous studies demonstrated that the distracted driving, such as using a cell phone while driving, disrupted the driver's performance on road. This study aimed to investigate the manner and extent to which cell phone use and driver's gender affected driving performance and collision risk in a rear-end collision avoidance process. Forty-two licensed drivers completed the driving simulation experiment in three phone use conditions: no phone use, hands-free, and hand-held, in which the drivers drove in a car-following situation with potential rear-end collision risks caused by the leading vehicle's sudden deceleration. Based on the experiment data, a rear-end collision risk assessment model was developed to assess the influence of cell phone use and driver's gender. The cell phone use and driver's gender were found to be significant factors that affected the braking performances in the rear-end collision avoidance process, including the brake reaction time, the deceleration adjusting time and the maximum deceleration rate. The minimum headway distance between the leading vehicle and the simulator during the rear-end collision avoidance process was the final output variable, which could be used to measure the rear-end collision risk and judge whether a collision occurred. The results showed that although cell phone use drivers took some compensatory behaviors in the collision avoidance process to reduce the mental workload, the collision risk in cell phone use conditions was still higher than that without the phone use. More importantly, the results proved that the hands-free condition did not eliminate the safety problem associated with distracted driving because it impaired the driving performance in the same way as much as the use of hand-held phones. In addition, the gender effect indicated that although female drivers had longer reaction time than male drivers in critical situation, they were more quickly in braking with larger maximum deceleration rate, and they tended to keep a larger safety margin with the leading vehicle compared to male drivers. The findings shed some light on the further development of advanced collision avoidance technologies and the targeted intervention strategies about cell phone use while driving. Copyright © 2016 Elsevier Ltd. All rights reserved.

Tool For Driving Many Fasteners Simultaneously

NASA Technical Reports Server (NTRS)

Cook, Joseph S., Jr.

1995-01-01

Proposed tool tightens or loosens several bolts, screws, nuts, or other threaded fasteners arranged in circle on compressor head, automotive wheel, pipe-end flange, or similar object. Enables assembly or disassembly in fraction of time needed to tighten fasteners one at a time. Simultaneously applies same torque to all fasteners, preventing distortion and enhancing reliability. Concept not limited to circular fastener patterns. Adapted to rectangular configurations like on engine intake manifolds, by adding gears to drive train to provide proper spacing. Designed to deliver fixed or adjustable maximum torque. To ensure even seal loading, piston pressure simultaneously ramped from initial to final values to maintain relatively constant torque loading on all fasteners until final specifications limit achieved.

Hydraulic Limits on Maximum Plant Transpiration

NASA Astrophysics Data System (ADS)

Manzoni, S.; Vico, G.; Katul, G. G.; Palmroth, S.; Jackson, R. B.; Porporato, A. M.

2011-12-01

Photosynthesis occurs at the expense of water losses through transpiration. As a consequence of this basic carbon-water interaction at the leaf level, plant growth and ecosystem carbon exchanges are tightly coupled to transpiration. In this contribution, the hydraulic constraints that limit transpiration rates under well-watered conditions are examined across plant functional types and climates. The potential water flow through plants is proportional to both xylem hydraulic conductivity (which depends on plant carbon economy) and the difference in water potential between the soil and the atmosphere (the driving force that pulls water from the soil). Differently from previous works, we study how this potential flux changes with the amplitude of the driving force (i.e., we focus on xylem properties and not on stomatal regulation). Xylem hydraulic conductivity decreases as the driving force increases due to cavitation of the tissues. As a result of this negative feedback, more negative leaf (and xylem) water potentials would provide a stronger driving force for water transport, while at the same time limiting xylem hydraulic conductivity due to cavitation. Here, the leaf water potential value that allows an optimum balance between driving force and xylem conductivity is quantified, thus defining the maximum transpiration rate that can be sustained by the soil-to-leaf hydraulic system. To apply the proposed framework at the global scale, a novel database of xylem conductivity and cavitation vulnerability across plant types and biomes is developed. Conductivity and water potential at 50% cavitation are shown to be complementary (in particular between angiosperms and conifers), suggesting a tradeoff between transport efficiency and hydraulic safety. Plants from warmer and drier biomes tend to achieve larger maximum transpiration than plants growing in environments with lower atmospheric water demand. The predicted maximum transpiration and the corresponding leaf water potential compare well with measured peak transpiration and minimum water potentials across plant types and biomes, suggesting that plant water transport system and stomatal regulation co-evolved to meet peak atmospheric demands, thus sustaining carbon uptake while avoiding tissue damage even in such harsh conditions.

Path Finding for Maximum Value of Information in Multi-Modal Underwater Wireless Sensor Networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gjanci, Petrika; Petrioli, Chiara; Basagni, Stefano

Here, we consider underwater multi-modal wireless sensor networks (UWSNs) suitable for applications on submarine surveillance and monitoring, where nodes offload data to a mobile autonomous underwater vehicle (AUV) via optical technology, and coordinate using acoustic communication. Sensed data are associated with a value, decaying in time. In this scenario, we address the problem of finding the path of the AUV so that the Value of Information (VoI) of the data delivered to a sink on the surface is maximized. We define a Greedy and Adaptive AUV Path-finding (GAAP) heuristic that drives the AUV to collect data from nodes depending onmore » the VoI of their data. For benchmarking the performance of AUV path-finding heuristics, we define an integer linear programming (ILP) formulation that accurately models the considered scenario, deriving a path that drives the AUV to collect and deliver data with the maximum VoI. In our experiments GAAP consistently delivers more than 80 percent of the theoretical maximum VoI determined by the ILP model. We also compare the performance of GAAP with that of other strategies for driving the AUV among sensing nodes, namely, random paths, TSP-based paths and a “lawn mower”-like strategy. Our results show that GAAP always outperforms every other heuristic in terms of delivered VoI, also obtaining higher energy efficiency.« less

Path Finding for Maximum Value of Information in Multi-Modal Underwater Wireless Sensor Networks

DOE PAGES

Gjanci, Petrika; Petrioli, Chiara; Basagni, Stefano; ...

2017-05-19

Here, we consider underwater multi-modal wireless sensor networks (UWSNs) suitable for applications on submarine surveillance and monitoring, where nodes offload data to a mobile autonomous underwater vehicle (AUV) via optical technology, and coordinate using acoustic communication. Sensed data are associated with a value, decaying in time. In this scenario, we address the problem of finding the path of the AUV so that the Value of Information (VoI) of the data delivered to a sink on the surface is maximized. We define a Greedy and Adaptive AUV Path-finding (GAAP) heuristic that drives the AUV to collect data from nodes depending onmore » the VoI of their data. For benchmarking the performance of AUV path-finding heuristics, we define an integer linear programming (ILP) formulation that accurately models the considered scenario, deriving a path that drives the AUV to collect and deliver data with the maximum VoI. In our experiments GAAP consistently delivers more than 80 percent of the theoretical maximum VoI determined by the ILP model. We also compare the performance of GAAP with that of other strategies for driving the AUV among sensing nodes, namely, random paths, TSP-based paths and a “lawn mower”-like strategy. Our results show that GAAP always outperforms every other heuristic in terms of delivered VoI, also obtaining higher energy efficiency.« less

Dependence of driving characteristics upon follower-leader combination

NASA Astrophysics Data System (ADS)

Nagahama, Akihito; Yanagisawa, Daichi; Nishinari, Katsuhiro

2017-10-01

The analysis of the microscopic view of mixed traffic offers a basis for resolving traffic jams which are inhomogeneous due to several types of vehicles. In this study, we research the dependence of driving characteristics upon vehicle order in a platoon. By focusing particularly upon the manner in which the driving characteristics of a follower are affected by both their own vehicle type and that of their leader, we measured the trajectories of platoons comprising two vehicles selected from motorcycles, passenger cars, and trucks on a test course. Analysis based on vehicle order showed that the vehicle types of both the leader and the follower as well as the leader's driving characteristics affected the velocity, acceleration, deceleration, operational delay of followers, and the distance gap between leaders and followers in different ways. In addition, we investigated the factors affecting driving characteristics by multiple regression analysis. We revealed that the operational delay and the maximum distance gap tend to be large when the length of leaders is large. Furthermore, as long as a follower can follow, we need not consider vehicle types among the parameters determining maximum velocity in car-following models. The vehicle types of the leader and the follower should be considered to determine maximum acceleration. When determining maximum deceleration, the vehicle types of the follower should be considered.

A programmable CCD driver circuit for multiphase CCD operation

NASA Technical Reports Server (NTRS)

Ewin, Audrey J.; Reed, Kenneth V.

1989-01-01

A programmable CCD (charge-coupled device) driver circuit was designed to drive CCDs in multiphased modes. The purpose of the drive electronics is to operate developmental CCD imaging arrays for NASA's tiltable moderate resolution imaging spectrometer (MODIS-T). Five objectives for the driver were considered during its design: (1) the circuit drives CCD electrode voltages between 0 V and +30 V to produce reasonable potential wells, (2) the driving sequence is started with one input signal, (3) the driving sequence is started with one input signal, (4) the circuit allows programming of frame sequences required by arrays of any size, (5) it produces interfacing signals for the CCD and the DTF (detector test facility). Simulation of the driver verified its function with the master clock running up to 10 MHz. This suggests a maximum rate of 400,000 pixels/s. Timing and packaging parameters were verified. The design uses 54 TTL (transistor-transistor logic) chips. Two versions of hardware were fabricated: wirewrap and printed circuit board. Both were verified functionally with a logic analyzer.

49 CFR 395.5 - Maximum driving time for passenger-carrying vehicles.

Code of Federal Regulations, 2010 CFR

2010-10-01

... hours in any 7 consecutive days if the employing motor carrier does not operate commercial motor vehicles every day of the week; or (2) Having been on duty 70 hours in any period of 8 consecutive days if the employing motor carrier operates commercial motor vehicles every day of the week. [70 FR 50073...

A driving cycle for vehicle emissions estimation in the metropolitan area of Mexico City.

PubMed

Schifter, I; Díaz, L; Rodríguez, R; López-Salinas, E

2005-02-01

A driving cycle derived from driving behavior and real traffic conditions in Mexico City (MC) is proposed. Data acquisition was carried out over diverse MC routes, representing travel under congested and uncongested conditions, using the chase-car approach. Thirteen different on-road patterns, including the four main access roads to MC, trips in both directions and different timetables, a total of 108 trips spanning 1044 km were evaluated in this study. The MC cycle lasts 1360 seconds with a distance of 8.8 km and average speed of 23.4 km h(-1). Both maximum speed (73.6 km h(-1)) and maximum acceleration (2.22 km h(-1)s(-1)) are lower than those of the new vehicles certification employed in Mexico ,FTP-75 cycle., that is, the MC cycle exhibits less cruising time and more transient events than the FTP cycle. A total of 30 light duty gasoline vehicles were classified into different technological groups and tested in an FTP-75 and MC driving cycles in order to compare their emission factors A potential concern is that in Mexico manufacturers design vehicles to meet the emission standards in the FTP, but emission levels increase significantly in a more representative cycle of present driving patterns in the Metropolitan Area of Mexico City (MAMC). The use of a more representative cycle during certification testing, would provide an incentive for vehicle manufacturers to design emissions control systems to remain effective during operation modes that are not currently represented in the official test procedures used in the certification process. Based on the results of the study, the use of MC cycle, which better represents current day driving patterns during testing of vehicle fleets in emissions laboratories, would improve the accuracy of emissions factors used in the MAMC emissions inventories.

49 CFR 571.126 - Standard No. 126; Electronic stability control systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... cycle that is designed for low-speed, off-road driving, or (b) the vehicle is in a four-wheel drive configuration selected by the driver on the previous ignition cycle that is designed for operation at higher.... Light outriggers are designed with a maximum weight of 27 kg (59.5 lb) and a maximum roll moment of...

A rod type linear ultrasonic motor utilizing longitudinal traveling waves: proof of concept

NASA Astrophysics Data System (ADS)

Wang, Liang; Wielert, Tim; Twiefel, Jens; Jin, Jiamei; Wallaschek, Jörg

2017-08-01

This paper proposes a non-resonant linear ultrasonic motor utilizing longitudinal traveling waves. The longitudinal traveling waves in the rod type stator are generated by inducing longitudinal vibrations at one end of the waveguide and eliminating reflections at the opposite end by a passive damper. Considering the Poisson’s effect, the stator surface points move on elliptic trajectories and the slider is driven forward by friction. In contrast to many other flexural traveling wave linear ultrasonic motors, the driving direction of the proposed motor is identical to the wave propagation direction. The feasibility of the motor concept is demonstrated theoretically and experimentally. First, the design and operation principle of the motor are presented in detail. Then, the stator is modeled utilizing the transfer matrix method and verified by experimental studies. In addition, experimental parameter studies are carried out to identify the motor characteristics. Finally, the performance of the proposed motor is investigated. Overall, the results indicate very dynamic drive characteristics. The motor prototype achieves a maximum mean velocity of 115 mm s-1 and a maximum load of 0.25 N. Thereby, the start-up and shutdown times from the maximum speed are lower than 5 ms.

A description of neck motor performance, neck pain, fatigue, and mental effort while driving in a sample with chronic whiplash-associated disorders.

PubMed

Takasaki, Hiroshi; Treleaven, Julia; Johnston, Venerina; Van den Hoorn, Wolbert; Rakotonirainy, Andry; Jull, Gwendolen

2014-08-01

Individuals with chronic whiplash-associated disorders (WADs) often note driving as a difficult task. This study's aims were to (1) compare, while driving, neck motor performance, mental effort, and fatigue in individuals with chronic WAD against healthy controls and (2) investigate the relationships of these variables and neck pain to self-reported driving difficulty in the WAD group. This study involved 14 participants in each group (WAD and control). Measures included self-reported driving difficulty and measures of neck pain intensity, overall fatigue, mental effort, and neck motor performance (head rotation and upper trapezius activity) while driving a simulator. The WAD group had greater absolute path of head rotation in a simulated city area and used greater mental effort (P = 0.04), but there were no differences in other measures while driving compared with the controls (all P ≥ 0.05). Self-reported driving difficulty correlated moderately with neck pain intensity, fatigue level, and maximum velocity of head rotation while driving in the WAD group (all P < 0.05). Individuals with chronic WAD do not seem to have impaired neck motor performance while driving yet use greater mental effort. Neck pain, fatigue, and maximum head rotation velocity could be potential contributors to self-reported driving difficulty in this group.

Dynamic Analysis of Heavy Vehicle Medium Duty Drive Shaft Using Conventional and Composite Material

NASA Astrophysics Data System (ADS)

Kumar, Ashwani; Jain, Rajat; Patil, Pravin P.

2016-09-01

The main highlight of this study is structural and modal analysis of single piece drive shaft for selection of material. Drive shaft is used for torque carrying from vehicle transmission to rear wheel differential system. Heavy vehicle medium duty transmission drive shaft was selected as research object. Conventional materials (Steel SM45 C, Stainless Steel) and composite materials (HS carbon epoxy, E Glass Polyester Resin Composite) were selected for the analysis. Single piece composite material drive shaft has advantage over conventional two-piece steel drive shaft. It has higher specific strength, longer life, less weight, high critical speed and higher torque carrying capacity. The main criteria for drive shaft failure are strength and weight. Maximum modal frequency obtained is 919 Hz. Various harmful vibration modes (lateral vibration and torsional vibration) were identified and maximum deflection region was specified. For single-piece drive shaft the natural bending frequency should be higher because it is subjected to torsion and shear stress. Single piece drive shaft was modelled using Solid Edge and Pro-E. Finite Element Analysis was used for structural and modal analysis with actual running boundary condition like frictional support, torque and moment. FEA simulation results were validated with experimental literature results.

A general method for the layout of ailerons and elevators of gliders and motorplanes

NASA Technical Reports Server (NTRS)

Hiller, M. H.

1979-01-01

A method is described which allows the layout of the spatial driving mechanism of the aileron for a glider or a motorplane to be performed in a systematic manner. In particular, a prescribed input-output behavior of the mechanism can be realized by variation of individual parameters of the spatial four-bar mechanisms which constitute the entire driving mechanism. By means of a sensitivity analysis, a systematic choice of parameters is possible. At the same time the forces acting in the mechanism can be limited by imposing maximum values of the forces as secondary conditions during the variation process.

49 CFR 395.3 - Maximum driving time for property-carrying vehicles.

Code of Federal Regulations, 2010 CFR

2010-10-01

... on duty 60 hours in any period of 7 consecutive days if the employing motor carrier does not operate commercial motor vehicles every day of the week; or (2) Having been on duty 70 hours in any period of 8 consecutive days if the employing motor carrier operates commercial motor vehicles every day of the week. (c...

Performance measurements and operational characteristics of the Storage Tek ACS 4400 tape library with the Cray Y-MP EL

NASA Technical Reports Server (NTRS)

Hull, Gary; Ranade, Sanjay

1993-01-01

With over 5000 units sold, the Storage Tek Automated Cartridge System (ACS) 4400 tape library is currently the most popular large automated tape library. Based on 3480/90 tape technology, the library is used as the migration device ('nearline' storage) in high-performance mass storage systems. In its maximum configuration, one ACS 4400 tape library houses sixteen 3480/3490 tape drives and is capable of holding approximately 6000 cartridge tapes. The maximum storage capacity of one library using 3480 tapes is 1.2 TB and the advertised aggregate I/O rate is about 24 MB/s. This paper reports on an extensive set of tests designed to accurately assess the performance capabilities and operational characteristics of one STK ACS 4400 tape library holding approximately 5200 cartridge tapes and configured with eight 3480 tape drives. A Cray Y-MP EL2-256 was configured as its host machine. More than 40,000 tape jobs were run in a variety of conditions to gather data in the areas of channel speed characteristics, robotics motion, time taped mounts, and timed tape reads and writes.

The rationale and design features for the 40 by 80/80 by 120 foot wind tunnel

NASA Technical Reports Server (NTRS)

Mort, K. W.; Kelly, M. W.; Hickey, D. H.

1976-01-01

A substantial increase in the test capability of full scale wind tunnels is considered. In order to determine the most cost effective means for providing this desired increase in test capability, a series of design studies were conducted of various new facilities as well as of major modifications to the existing 40- by 80-foot wind tunnel. The most effective trade between test capability and facility cost was provided by repowering the existing 40 by 80 foot wind tunnel to increase the maximum speed from 200 knots to 300 knots and by the addition of a new 80- by 120-foot test section having a 110 knot maximum speed. The design of the facility is described with special emphasis on the unique features, such as the drive system which absorbs nearly four times the power without an increase in noise, and the large flow diversion devices required to interface the two test sections to a single drive.

Compilation of load spectrum of loader drive axle

NASA Astrophysics Data System (ADS)

Wei, Yongxiang; Zhu, Haoyue; Tang, Heng; Yuan, Qunwei

2018-03-01

In order to study the preparation method of gear fatigue load spectrum for loaders, the load signal of four typical working conditions of loader is collected. The signal that reflects the law of load change is obtained by preprocessing the original signal. The torque of the drive axle is calculated by using the rain flow counting method. According to the operating time ratio of each working condition, the two dimensional load spectrum based on the real working conditions of the drive axle of loader is established by the cycle extrapolation and synthesis method. The two-dimensional load spectrum is converted into one-dimensional load spectrum by means of the mean of torque equal damage method. Torque amplification includes the maximum load torque of the main reduction gear. Based on the theory of equal damage, the accelerated cycles are calculated. In this way, the load spectrum of the loading condition of the drive axle is prepared to reflect loading condition of the loader. The load spectrum can provide reference for fatigue life test and life prediction of loader drive axle.

Modular, Microprocessor-Controlled Flash Lighting System

NASA Technical Reports Server (NTRS)

Kiefer, Dwayne; Gray, Elizabeth; Skupinski, Robert; Stachowicz, Arthur; Birchenough, William

2006-01-01

A microprocessor-controlled lighting system generates brief, precisely timed, high-intensity flashes of light for scientific imaging at frame rates up to about 1 kHz. The system includes an array of light-emitting diodes (LEDs) that are driven in synchronism with an externally generated timing signal (for example, a timing signal generated by a video camera). The light output can be varied in peak intensity, pulse duration, pulse delay, and pulse rate, all depending on the timing signal and associated externally generated control signals. The array of LEDs comprises as many as 16 LED panels that can be attached together. Each LED panel is a module consisting of a rectangular subarray of 10 by 20 LEDs of advanced design on a printed-circuit board in a mounting frame with a power/control connector. The LED panels are controlled by an LED control module that contains an AC-to-DC power supply, a control board, and 8 LED-panel driver boards. In prior LED panels, the LEDs are packaged at less than maximum areal densities in bulky metal housings that reduce effective active areas. In contrast, in the present LED panels, the LEDs are packed at maximum areal density so as to afford 100-percent active area and so that when panels are joined side by side to form the array, there are no visible seams between them and the proportion of active area is still 100 percent. Each panel produces an illuminance of .5 x 10( exp 4) lux at a distance of 5.8 in. (approx.1.6 cm). The LEDs are driven according to a pulse-width-modulation control scheme that makes it safe to drive the LEDs beyond their rated steady-state currents in order to generate additional light during short periods. The drive current and the pulse-width modulation for each LED panel can be controlled independently of those of the other 15 panels. The maximum allowable duration of each pulse of drive current is a function of the amount of overdrive, the total time to be spent in overdrive operation, and the limitations of the LEDs. The system is configured to limit the overdrive according to values specific to each type of LED in the array. These values are coded into firmware to prevent inadvertent damage to the LED panels.

Assessing drivers' response during automated driver support system failures with non-driving tasks.

PubMed

Shen, Sijun; Neyens, David M

2017-06-01

With the increase in automated driver support systems, drivers are shifting from operating their vehicles to supervising their automation. As a result, it is important to understand how drivers interact with these automated systems and evaluate their effect on driver responses to safety critical events. This study aimed to identify how drivers responded when experiencing a safety critical event in automated vehicles while also engaged in non-driving tasks. In total 48 participants were included in this driving simulator study with two levels of automated driving: (a) driving with no automation and (b) driving with adaptive cruise control (ACC) and lane keeping (LK) systems engaged; and also two levels of a non-driving task (a) watching a movie or (b) no non-driving task. In addition to driving performance measures, non-driving task performance and the mean glance duration for the non-driving task were compared between the two levels of automated driving. Drivers using the automated systems responded worse than those manually driving in terms of reaction time, lane departure duration, and maximum steering wheel angle to an induced lane departure event. These results also found that non-driving tasks further impaired driver responses to a safety critical event in the automated system condition. In the automated driving condition, driver responses to the safety critical events were slower, especially when engaged in a non-driving task. Traditional driver performance variables may not necessarily effectively and accurately evaluate driver responses to events when supervising autonomous vehicle systems. Thus, it is important to develop and use appropriate variables to quantify drivers' performance under these conditions. Copyright © 2017 Elsevier Ltd and National Safety Council. All rights reserved.

A Quadruped Micro-Robot Based on Piezoelectric Driving

PubMed Central

Su, Qi; Quan, Qiquan; Deng, Jie; Yu, Hongpeng

2018-01-01

Inspired by a way of rowing, a new piezoelectric driving quadruped micro-robot operating in bending-bending hybrid vibration modes was proposed and tested in this work. The robot consisted of a steel base, four steel connecting pins and four similar driving legs, and all legs were bonded by four piezoelectric ceramic plates. The driving principle is discussed, which is based on the hybrid of first order vertical bending and first order horizontal bending vibrations. The bending-bending hybrid vibration modes motivated the driving foot to form an elliptical trajectory in space. The vibrations of four legs were used to provide the driving forces for robot motion. The proposed robot was fabricated and tested according to driving principle. The vibration characteristics and elliptical movements of the driving feet were simulated by FEM method. Experimental tests of vibration characteristics and mechanical output abilities were carried out. The tested resonance frequencies and vibration amplitudes agreed well with the FEM calculated results. The size of robot is 36 mm × 98 mm × 14 mm, its weight is only 49.8 g, but its maximum load capacity achieves 200 g. Furthermore, the robot can achieve a maximum speed of 33.45 mm/s. PMID:29518964

A Quadruped Micro-Robot Based on Piezoelectric Driving.

PubMed

Su, Qi; Quan, Qiquan; Deng, Jie; Yu, Hongpeng

2018-03-07

Inspired by a way of rowing, a new piezoelectric driving quadruped micro-robot operating in bending-bending hybrid vibration modes was proposed and tested in this work. The robot consisted of a steel base, four steel connecting pins and four similar driving legs, and all legs were bonded by four piezoelectric ceramic plates. The driving principle is discussed, which is based on the hybrid of first order vertical bending and first order horizontal bending vibrations. The bending-bending hybrid vibration modes motivated the driving foot to form an elliptical trajectory in space. The vibrations of four legs were used to provide the driving forces for robot motion. The proposed robot was fabricated and tested according to driving principle. The vibration characteristics and elliptical movements of the driving feet were simulated by FEM method. Experimental tests of vibration characteristics and mechanical output abilities were carried out. The tested resonance frequencies and vibration amplitudes agreed well with the FEM calculated results. The size of robot is 36 mm × 98 mm × 14 mm, its weight is only 49.8 g, but its maximum load capacity achieves 200 g. Furthermore, the robot can achieve a maximum speed of 33.45 mm/s.

Effects of electronic billboards on driver distraction.

PubMed

Dukic, Tania; Ahlstrom, Christer; Patten, Christopher; Kettwich, Carmen; Kircher, Katja

2013-01-01

There is an increase in electronic advertising billboards along major roads, which may cause driver distraction due to the highly conspicuous design of the electronic billboards. Yet limited research on the impact of electronic billboards on driving performance and driver behavior is available. The Swedish Transport Administration recently approved the installation of 12 electronic billboards for a trial period along a 3-lane motorway with heavy traffic running through central Stockholm, Sweden. The aim of this study was to evaluate the effect of these electronic billboards on visual behavior and driving performance. A total of 41 drivers were recruited to drive an instrumented vehicle passing 4 of the electronic billboards during day and night conditions. A driver was considered visually distracted when looking at a billboard continuously for more than 2 s or if the driver looked away from the road for a high percentage of time. Dependent variables were eye-tracking measures and driving performance measures. The visual behavior data showed that drivers had a significantly longer dwell time, a greater number of fixations, and longer maximum fixation duration when driving past an electronic billboard compared to other signs on the same road stretches. No differences were found for the factors day/night, and no effect was found for the driving behavior data. Electronic billboards have an effect on gaze behavior by attracting more and longer glances than regular traffic signs. Whether the electronic billboards attract too much attention and constitute a traffic safety hazard cannot be answered conclusively based on the present data.

Electric-drive tractability indicator integrated in hybrid electric vehicle tachometer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tamai, Goro; Zhou, Jing; Weslati, Feisel

An indicator, system and method of indicating electric drive usability in a hybrid electric vehicle. A tachometer is used that includes a display having an all-electric drive portion and a hybrid drive portion. The all-electric drive portion and the hybrid drive portion share a first boundary which indicates a minimum electric drive usability and a beginning of hybrid drive operation of the vehicle. The indicated level of electric drive usability is derived from at least one of a percent battery discharge, a percent maximum torque provided by the electric drive, and a percent electric drive to hybrid drive operating costmore » for the hybrid electric vehicle.« less

Dynamic performance of maximum power point tracking circuits using sinusoidal extremum seeking control for photovoltaic generation

NASA Astrophysics Data System (ADS)

Leyva, R.; Artillan, P.; Cabal, C.; Estibals, B.; Alonso, C.

2011-04-01

The article studies the dynamic performance of a family of maximum power point tracking circuits used for photovoltaic generation. It revisits the sinusoidal extremum seeking control (ESC) technique which can be considered as a particular subgroup of the Perturb and Observe algorithms. The sinusoidal ESC technique consists of adding a small sinusoidal disturbance to the input and processing the perturbed output to drive the operating point at its maximum. The output processing involves a synchronous multiplication and a filtering stage. The filter instance determines the dynamic performance of the MPPT based on sinusoidal ESC principle. The approach uses the well-known root-locus method to give insight about damping degree and settlement time of maximum-seeking waveforms. This article shows the transient waveforms in three different filter instances to illustrate the approach. Finally, an experimental prototype corroborates the dynamic analysis.

Energy Storage | Transportation Research | NREL

Science.gov Websites

, and safe energy storage systems to power the next generation of electric-drive vehicles (EDVs). While lasting, safe, and operate at maximum efficiency in a wide range of driving conditions and climates. The Consumers, Industry, and the Environment As manufacturers develop new electric-drive vehicles, NREL acts as

Soil water retention and maximum capillary drive from saturation to oven dryness

USGS Publications Warehouse

Morel-Seytoux, Hubert J.; Nimmo, John R.

1999-01-01

This paper provides an alternative method to describe the water retention curve over a range of water contents from saturation to oven dryness. It makes two modifications to the standard Brooks and Corey [1964] (B-C) description, one at each end of the suction range. One expression proposed by Rossi and Nimmo [1994] is used in the high-suction range to a zero residual water content. (This Rossi-Nimmo modification to the Brooks-Corey model provides a more realistic description of the retention curve at low water contents.) Near zero suction the second modification eliminates the region where there is a change in suction with no change in water content. Tests on seven soil data sets, using three distinct analytical expressions for the high-, medium-, and low-suction ranges, show that the experimental water retention curves are well fitted by this composite procedure. The high-suction range of saturation contributes little to the maximum capillary drive, defined with a good approximation for a soil water and air system as HcM = ∫0∞ Krwdhc , where krw is relative permeability (or conductivity) to water and hc is capillary suction, a positive quantity in unsaturated soils. As a result, the modification suggested to describe the high-suction range does not significantly affect the equivalence between Brooks-Corey (B-C) and van Genuchten [1980] parameters presented earlier. However, the shape of the retention curve near “natural saturation” has a significant impact on the value of the capillary drive. The estimate using the Brooks-Corey power law, extended to zero suction, will exceed that obtained with the new procedure by 25 to 30%. It is not possible to tell which procedure is appropriate. Tests on another data set, for which relative conductivity data are available, support the view of the authors that measurements of a retention curve coupled with a speculative curve of relative permeability as from a capillary model are not sufficient to accurately determine the (maximum) capillary drive. The capillary drive is a dynamic scalar, whereas the retention curve is of a static character. Only measurements of infiltration rates with time can determine the capillary drive with precision for a given soil.

Measurements of admittances and characteristic combustion times of reactive gaseous propellant coaxial injectors

NASA Technical Reports Server (NTRS)

Janardan, B. A.; Daniel, B. R.; Zinn, B. T.

1979-01-01

The results of an experimental investigation that was concerned with the quantitative determination of the capabilities of combustion processes associated with coaxial injectors to amplify and sustain combustor oscillations was described. The driving provided by the combustion process was determined by employing the modified standing-wave method utilizing coaxial injectors and air-acetylene mixtures. Analyses of the measured data indicate that the investigated injectors are capable of initiating and amplifying combustion instabilities under favorable conditions of injector-combustion coupling and over certain frequency ranges. These frequency ranges and the frequency at which an injector's driving capacity is maximum are observed to depend upon the equivalence ratio, the pressure drop across the injector orifices and the number of injector elements. The characteristic combustion times of coaxial injectors were determined from steady state temperature measurements.

Modeling and Simulation of Control Actuation System with Fuzzy-PID Logic Controlled Brushless Motor Drives for Missiles Glider Applications

PubMed Central

Muniraj, Murali; Arulmozhiyal, Ramaswamy

2015-01-01

A control actuation system has been used extensively in automotive, aerospace, and defense applications. The major challenges in modeling control actuation system are rise time, maximum peak to peak overshoot, and response to nonlinear system with percentage error. This paper addresses the challenges in modeling and real time implementation of control actuation system for missiles glider applications. As an alternative fuzzy-PID controller is proposed in BLDC motor drive followed by linkage mechanism to actuate fins in missiles and gliders. The proposed system will realize better rise time and less overshoot while operating in extreme nonlinear dynamic system conditions. A mathematical model of BLDC motor is derived in state space form. The complete control actuation system is modeled in MATLAB/Simulink environment and verified by performing simulation studies. A real time prototype of the control actuation is developed with dSPACE-1104 hardware controller and a detailed analysis is carried out to confirm the viability of the proposed system. PMID:26613102

Modeling and Simulation of Control Actuation System with Fuzzy-PID Logic Controlled Brushless Motor Drives for Missiles Glider Applications.

PubMed

Muniraj, Murali; Arulmozhiyal, Ramaswamy

2015-01-01

A control actuation system has been used extensively in automotive, aerospace, and defense applications. The major challenges in modeling control actuation system are rise time, maximum peak to peak overshoot, and response to nonlinear system with percentage error. This paper addresses the challenges in modeling and real time implementation of control actuation system for missiles glider applications. As an alternative fuzzy-PID controller is proposed in BLDC motor drive followed by linkage mechanism to actuate fins in missiles and gliders. The proposed system will realize better rise time and less overshoot while operating in extreme nonlinear dynamic system conditions. A mathematical model of BLDC motor is derived in state space form. The complete control actuation system is modeled in MATLAB/Simulink environment and verified by performing simulation studies. A real time prototype of the control actuation is developed with dSPACE-1104 hardware controller and a detailed analysis is carried out to confirm the viability of the proposed system.

49 CFR 525.7 - Basis for petition.

Code of Federal Regulations, 2012 CFR

2012-10-01

... to be manufactured in that affected model year; (1) Maximum overall body width, overall length, and... applicable; (6) Drive train configuration and total drive ratio; (7) Emission control system; (8) Dynamometer...

49 CFR 525.7 - Basis for petition.

Code of Federal Regulations, 2011 CFR

2011-10-01

... to be manufactured in that affected model year; (1) Maximum overall body width, overall length, and... applicable; (6) Drive train configuration and total drive ratio; (7) Emission control system; (8) Dynamometer...

49 CFR 525.7 - Basis for petition.

Code of Federal Regulations, 2013 CFR

2013-10-01

... to be manufactured in that affected model year; (1) Maximum overall body width, overall length, and... applicable; (6) Drive train configuration and total drive ratio; (7) Emission control system; (8) Dynamometer...

A small, linear, piezoelectric ultrasonic cryomotor

NASA Astrophysics Data System (ADS)

Dong, Shuxiang; Yan, Li; Wang, Naigang; Viehland, Dwight; Jiang, Xiaoning; Rehrig, Paul; Hackenberger, Wes

2005-01-01

A small, linear-type, piezoelectric ultrasonic cryomotor has been developed for precision positioning at extremely low temperatures (⩾-200°C). This cryomotor consists of a pair of Pb(Mg1/3Nb2/3)O3-PbTiO3 single crystal stacks, which are piezoelectrically excited into the rotating third-bending mode of the cryomotor stator's center, which in turn drives a contacted slider into linear motion via frictional forces. The performance characteristics achieved by the cryomotor are: (i) a maximum linear speed of >50mm /s; (ii) a stroke of >10mm; (iii) a driving force of >0.2N; (iv) a response time of ˜29ms; and (v) a step resolution of ˜20nm.

PWM-switching pattern-based diagnosis scheme for single and multiple open-switch damages in VSI-fed induction motor drives.

PubMed

Trabelsi, Mohamed; Boussak, Mohamed; Gossa, Moncef

2012-03-01

This paper deals with a fault detection technique for insulated-gate bipolar transistors (IGBTs) open-circuit faults in voltage source inverter (VSI)-fed induction motor drives. The novelty of this idea consists in analyzing the pulse-width modulation (PWM) switching signals and the line-to-line voltage levels during the switching times, under both healthy and faulty operating conditions. The proposed method requires line-to-line voltage measurement, which provides information about switching states and is not affected by the load. The fault diagnosis scheme is achieved using simple hardware and can be included in the existing inverter system without any difficulty. In addition, it allows not only accurate single and multiple faults diagnosis but also minimization of the fault detection time to a maximum of one switching period (T(c)). Simulated and experimental results on a 3-kW squirrel-cage induction motor drive are displayed to validate the feasibility and the effectiveness of the proposed strategy. Crown Copyright © 2011. Published by Elsevier Ltd. All rights reserved.

Real-time stop sign detection and distance estimation using a single camera

NASA Astrophysics Data System (ADS)

Wang, Wenpeng; Su, Yuxuan; Cheng, Ming

2018-04-01

In modern world, the drastic development of driver assistance system has made driving a lot easier than before. In order to increase the safety onboard, a method was proposed to detect STOP sign and estimate distance using a single camera. In STOP sign detection, LBP-cascade classifier was applied to identify the sign in the image, and the principle of pinhole imaging was based for distance estimation. Road test was conducted using a detection system built with a CMOS camera and software developed by Python language with OpenCV library. Results shows that that the proposed system reach a detection accuracy of maximum of 97.6% at 10m, a minimum of 95.00% at 20m, and 5% max error in distance estimation. The results indicate that the system is effective and has the potential to be used in both autonomous driving and advanced driver assistance driving systems.

Synchronization of unidirectionally coupled Mackey-Glass analog circuits with frequency bandwidth limitations.

PubMed

Kim, Min-Young; Sramek, Christopher; Uchida, Atsushi; Roy, Rajarshi

2006-07-01

Synchronization of chaotic systems has been studied extensively, and especially, the possible applications to the communication systems motivated many research areas. We demonstrate the effect of the frequency bandwidth limitations in the communication channel on the synchronization of two unidirectionally coupled Mackey-Glass (MG) analog circuits, both numerically and experimentally. MG system is known to generate high dimensional chaotic signals. The chaotic signal generated from the drive MG system is modified by a low pass filter and is then transmitted to the response MG system. Our results show that the inclusion of the dominant frequency component of the original drive signals is crucial to achieve synchronization between the drive and response circuits. The maximum cross correlation and the corresponding time shift reveal that the frequency-dependent coupling introduced by the low pass filtering effect in the communication channel change the quality of synchronization.

14 CFR 27.923 - Rotor drive system and control mechanism tests.

Code of Federal Regulations, 2010 CFR

2010-01-01

... the position that will give maximum longitudinal cyclic pitch change to simulate forward flight. The... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Rotor drive system and control mechanism....923 Rotor drive system and control mechanism tests. (a) Each part tested as prescribed in this section...

Rapid Microfluidic Mixers Utilizing Dispersion Effect and Interactively Time-Pulsed Injection

NASA Astrophysics Data System (ADS)

Leong, Jik-Chang; Tsai, Chien-Hsiung; Chang, Chin-Lung; Lin, Chiu-Feng; Fu, Lung-Ming

2007-08-01

In this paper, we present a novel active microfluidic mixer utilizing a dispersion effect in an expansion chamber and applying interactively time-pulsed driving voltages to the respective inlet fluid flows to induce electroosmotic flow velocity variations for developing a rapid mixing effect in a microchannel. Without using any additional equipment to induce flow perturbations, only a single high-voltage power source is required for simultaneously driving and mixing sample fluids, which results in a simple and low-cost system for mixing. The effects of the applied main electrical field, interactive frequency, and expansion ratio on the mixing performance are thoroughly examined experimentally and numerically. The mixing ratio can be as high as 95% within a mixing length of 3000 μm downstream from the secondary T-form when a driving electric field strength of 250 V/cm, a periodic switching frequency of 5 Hz, and the expansion ratio M=1:10 are applied. In addition, the optimization of the driving electric field, switching frequency, expansion ratio, expansion entry length, and expansion chamber length for achieving a maximum mixing ratio is also discussed in this study. The novel method proposed in this study can be used for solving the mixing problem in the field of micro-total-analysis systems in a simple manner.

Investigation into pedestrian exposure to near-vehicle exhaust emissions

PubMed Central

2009-01-01

Background Inhalation of diesel particulate matter (DPM) is known to have a negative impact on human health. Consequently, there are regulations and standards that limit the maximum concentrations to which persons may be exposed and the maximum concentrations allowed in the ambient air. However, these standards consider steady exposure over large spatial and time scales. Due to the nature of many vehicle exhaust systems, pedestrians in close proximity to a vehicle's tailpipe may experience events where diesel particulate matter concentrations are high enough to cause acute health effects for brief periods of time. Methods In order to quantify these exposure events, instruments which measure specific exhaust constituent concentrations were placed near a roadway and connected to the mouth of a mannequin used as a pedestrian surrogate. By measuring concentrations at the mannequin's mouth during drive-by events with a late model diesel truck, a representative estimate of the exhaust constituent concentrations to which a pedestrian may be exposed was obtained. Typical breathing rates were then multiplied by the measured concentrations to determine the mass of pollutant inhaled. Results The average concentration of diesel particulate matter measured over the duration of a single drive-by test often exceeded the low concentrations used in human clinical studies which are known to cause acute health effects. It was also observed that higher concentrations of diesel particulate matter were measured at the height of a stroller than were measured at the mouth of a mannequin. Conclusion Diesel particulate matter concentrations during drive-by incidents easily reach or exceed the low concentrations that can cause acute health effects for brief periods of time. For the case of a particularly well-tuned late-model year vehicle, the mass of particulate matter inhaled during a drive-by incident is small compared to the mass inhaled daily at ambient conditions. On a per breath basis, however, the mass of particulate matter inhaled is large compared to the mass inhaled at ambient conditions. Finally, it was determined that children, infants, or people breathing at heights similar to that of a passing vehicle's tailpipe may be exposed to higher concentrations of particulate matter than those breathing at higher locations, such as adults standing up. PMID:19331669

Wide range scaling laws for radiation driven shock speed, wall albedo and ablation parameters for high-Z materials

NASA Astrophysics Data System (ADS)

Mishra, Gaurav; Ghosh, Karabi; Ray, Aditi; Gupta, N. K.

2018-06-01

Radiation hydrodynamic (RHD) simulations for four different potential high-Z hohlraum materials, namely Tungsten (W), Gold (Au), Lead (Pb), and Uranium (U) are performed in order to investigate their performance with respect to x-ray absorption, re-emission and ablation properties, when irradiated by constant temperature drives. A universal functional form is derived for estimating time dependent wall albedo for high-Z materials. Among the high-Z materials studied, it is observed that for a fixed simulation time the albedo is maximum for Au below 250 eV, whereas it is maximum for U above 250 eV. New scaling laws for shock speed vs drive temperature, applicable over a wide temperature range of 100 eV to 500 eV, are proposed based on the physics of x-ray driven stationary ablation. The resulting scaling relation for a reference material Aluminium (Al), shows good agreement with that of Kauffman's power law for temperatures ranging from 100 eV to 275 eV. New scaling relations are also obtained for temperature dependent mass ablation rate and ablation pressure, through RHD simulation. Finally, our study reveals that for temperatures above 250 eV, U serves as a better hohlraum material since it offers maximum re-emission for x-rays along with comparable mass ablation rate. Nevertheless, traditional choice, Au works well for temperatures below 250 eV. Besides inertial confinement fusion (ICF), the new scaling relations may find its application in view-factor codes, which generally ignore atomic physics calculations of opacities and emissivities, details of laser-plasma interaction and hydrodynamic motions.

Throughput times for adults and children during two drive-through influenza vaccination clinics.

PubMed

Banks, Laura L; Crandall, Cameron; Esquibel, Luke

2013-04-01

Successful planning for public health emergencies requires knowledge of effective methods for mass distribution of medication and supplies to the public. We measured the time required for the key components of 2 drive-through vaccination clinics and summarized the results as they applied to providing medical countermeasures to large populations of children and adults. We hypothesized that vaccinating children in addition to adults would affect throughput time. Using 2 separate drive-through vaccination clinics, we measured elapsed time for vehicle flow and vaccination procedures. We calculated the median length of stay and the time to administer vaccinations based on the number of individual vaccinations given per vehicle, and compared the vehicles in which children (aged 9-18 years) were vaccinated to those in which only adults were vaccinated. A total of 2174 vaccinations and 1275 vehicles were timed during the 2 clinics. The number of vaccinations and vehicles per hour varied during the course of the day; the maximums were 200 and 361 per hour, respectively. The median throughput time was 5 minutes, and the median vaccination time was 48 seconds. Flow over time varied by the hour, and the optimum number of vaccinations per vehicle to maximize efficiency was between 3 and 4. Our findings showed that the presence of children raised the total number of vaccinations given per vehicle and, therefore, the total vaccination processing time per vehicle. However, the median individual procedure time in the vehicles with children was not significantly increased, indicating no need to calculate increased times for processing children 9 years of age or older during emergency planning. Drive-through clinics can provide a large number of seasonal influenza vaccinations in a relatively efficient manner; provide needed experience for students and practitioners in techniques for mass administration of medical countermeasures; and assist public health and emergency management personnel with disaster planning. Including children older than 9 years does not reduce efficiency. (Disaster Med Public Health Preparedness. 2013;0:1-7).

Systems Engineering Methodology for Fuel Efficiency and its Application to the TARDEC Fuel Efficient Demonstrator (FED) Program

DTIC Science & Technology

2010-08-19

highlight the benefits of regenerative braking . Parameters within the drive cycle may include vehicle speed, elevation/grade changes, road surface...assist to downsize the engine due to infinite maximum speed requirements • Drive cycle less suited to regenerative braking improvement compared to...will be cycle dependent. A high speed drive cycle may for example drive a focus on aerodynamic improvements, while high frequency of braking will

Energy and electrode consumption analysis of electrocoagulation for the removal of arsenic from underground water.

PubMed

Martínez-Villafañe, J F; Montero-Ocampo, C; García-Lara, A M

2009-12-30

A systematic study of the effect of design and operation conditions of an electrochemical reactor on the treatment time for arsenic (As) electro-removal from underground water (GW) was carried out to analyse the energy and electrode consumption. The effects of four factors--current density, interelectrode distance, electrode area-volume ratio, and liquid motion driving mode--were evaluated. The response variables were the energy and the electrode consumption and the treatment time to reduce the GW residual As concentration to 10 microg L(-1), which is the maximum contaminant level (MCL) established by the World Health Organization (WHO) in drinking water. The results obtained in this study showed that the factor that had the greatest effect on most of the response variables was the liquid motion driving mode. The best residence time was 20s, which favoured low energy consumption (58.78 Wh m(-3)) and low electrode material loss (9.59 g m(-3)).

Optimization and Analysis of a U-Shaped Linear Piezoelectric Ultrasonic Motor Using Longitudinal Transducers

PubMed Central

Yu, Hongpeng; Quan, Qiquan; Tian, Xinqi; Li, He

2018-01-01

A novel U-shaped piezoelectric ultrasonic motor that mainly focused on miniaturization and high power density was proposed, fabricated, and tested in this work. The longitudinal vibrations of the transducers were excited to form the elliptical movements on the driving feet. Finite element method (FEM) was used for design and analysis. The resonance frequencies of the selected vibration modes were tuned to be very close to each other with modal analysis and the movement trajectories of the driving feet were gained with transient simulation. The vibration modes and the mechanical output abilities were tested to evaluate the proposed motor further by a prototype. The maximum output speed was tested to be 416 mm/s, the maximum thrust force was 21 N, and the maximum output power was 5.453 W under frequency of 29.52 kHz and voltage of 100 Vrms. The maximum output power density of the prototype reached 7.59 W/kg, which was even greater than a previous similar motor under the exciting voltage of 200 Vrms. The proposed motor showed great potential for linear driving of large thrust force and high power density. PMID:29518963

Optimization and Analysis of a U-Shaped Linear Piezoelectric Ultrasonic Motor Using Longitudinal Transducers.

PubMed

Yu, Hongpeng; Quan, Qiquan; Tian, Xinqi; Li, He

2018-03-07

A novel U-shaped piezoelectric ultrasonic motor that mainly focused on miniaturization and high power density was proposed, fabricated, and tested in this work. The longitudinal vibrations of the transducers were excited to form the elliptical movements on the driving feet. Finite element method (FEM) was used for design and analysis. The resonance frequencies of the selected vibration modes were tuned to be very close to each other with modal analysis and the movement trajectories of the driving feet were gained with transient simulation. The vibration modes and the mechanical output abilities were tested to evaluate the proposed motor further by a prototype. The maximum output speed was tested to be 416 mm/s, the maximum thrust force was 21 N, and the maximum output power was 5.453 W under frequency of 29.52 kHz and voltage of 100 V rms . The maximum output power density of the prototype reached 7.59 W/kg, which was even greater than a previous similar motor under the exciting voltage of 200 V rms . The proposed motor showed great potential for linear driving of large thrust force and high power density.

Investigation of efficiency of electric drive control system of excavator traction mechanism based on feedback on load

NASA Astrophysics Data System (ADS)

Kuznetsov, N. K.; Iov, I. A.; Iov, A. A.

2018-05-01

The article presents the results of a study of the efficiency of the electric drive control system of the traction mechanism of a dragline based on the use of feedback on load in the traction cable. The investigations were carried out using a refined electromechanical model of the traction mechanism, which took into account not only the elastic elements of the gearbox, the backlashes in it and the changes in the kinematic parameters of the mechanism during operation, but also the mechanical characteristics of the electric drive and the features of its control system. By mathematical modeling of the transient processes of the electromechanical system, it is shown that the introduction of feedback on the load in the elastic element allows one to reduce the dynamic loads in the traction mechanism and to limit the elastic oscillations of the actuating mechanism in comparison with the standard control system. Fixed as a general decrease in the dynamic load of the nodes of traction mechanism in the modes of loading and latching of the bucket, and a decrease the operating time of the mechanism at maximum load. At the same time, undesirable phenomena in the operation of the electric drive were also associated with the increase in the recovery time of the steady-state value of the speed of the actuating mechanism under certain operating conditions, which can lead to a decrease in the reliability of the mechanical part and the productivity of the traction mechanism.

Optimal Control for Quantum Driving of Two-Level Systems

NASA Astrophysics Data System (ADS)

Qi, Xiao-Qiu

2018-01-01

In this paper, the optimal quantum control of two-level systems is studied by the decompositions of SU(2). Using the Pontryagin maximum principle, the minimum time of quantum control is analyzed in detail. The solution scheme of the optimal control function is given in the general case. Finally, two specific cases, which can be applied in many quantum systems, are used to illustrate the scheme, while the corresponding optimal control functions are obtained.

The Sequence of Hip and Selected Upper-Extremity Joint Movements During the Golf Drive.

ERIC Educational Resources Information Center

Hunter, Charles L.

This study analyzed wrist, elbow, and hip actions of golfers who were accurately driving a golf ball a maximum distance. Electrogoniometry and cinematography were used to measure wrist, forearm, elbow, and hip actions during the downswing of 10 low-handicap golfers who were attempting to drive a minimum of 225 yards within a 50-yard corridor.…

Training-specific functional, neural, and hypertrophic adaptations to explosive- vs. sustained-contraction strength training.

PubMed

Balshaw, Thomas G; Massey, Garry J; Maden-Wilkinson, Thomas M; Tillin, Neale A; Folland, Jonathan P

2016-06-01

Training specificity is considered important for strength training, although the functional and underpinning physiological adaptations to different types of training, including brief explosive contractions, are poorly understood. This study compared the effects of 12 wk of explosive-contraction (ECT, n = 13) vs. sustained-contraction (SCT, n = 16) strength training vs. control (n = 14) on the functional, neural, hypertrophic, and intrinsic contractile characteristics of healthy young men. Training involved 40 isometric knee extension repetitions (3 times/wk): contracting as fast and hard as possible for ∼1 s (ECT) or gradually increasing to 75% of maximum voluntary torque (MVT) before holding for 3 s (SCT). Torque and electromyography during maximum and explosive contractions, torque during evoked octet contractions, and total quadriceps muscle volume (QUADSVOL) were quantified pre and post training. MVT increased more after SCT than ECT [23 vs. 17%; effect size (ES) = 0.69], with similar increases in neural drive, but greater QUADSVOL changes after SCT (8.1 vs. 2.6%; ES = 0.74). ECT improved explosive torque at all time points (17-34%; 0.54 ≤ ES ≤ 0.76) because of increased neural drive (17-28%), whereas only late-phase explosive torque (150 ms, 12%; ES = 1.48) and corresponding neural drive (18%) increased after SCT. Changes in evoked torque indicated slowing of the contractile properties of the muscle-tendon unit after both training interventions. These results showed training-specific functional changes that appeared to be due to distinct neural and hypertrophic adaptations. ECT produced a wider range of functional adaptations than SCT, and given the lesser demands of ECT, this type of training provides a highly efficient means of increasing function. Copyright © 2016 the American Physiological Society.

Batu Pahat Driving Cycle for Light Duty Gasoline Engine

NASA Astrophysics Data System (ADS)

Zainul Abidin, Zainul Ameerul Ikhsan B.; Faisal Hushim, Mohd; Ahmad, Osman Bin

2017-08-01

Driving cycle is a series of data points that represents the vehicle speed versus time. Transient driving cycles involve many changes such as frequent speed changes during typical on-road driving condition [2]. Model driving cycles involve protracted periods at constant speeds. The Batu Pahat Driving Cycle (BPDC) developed to represent the driving pattern of people in a district of Batu Pahat. Based on this driving cycle, it will be a reference to other researchers to study about the gases emission release and fuel consumption by the vehicle on the dynamometer or automotive simulation based on this driving cycle. Existing driving cycles used such as the New European Driving Cycle (NEDC), the Federal Test Procedure (FTP-72/75, and Japan 10-15 Mode Cycle is not appropriate for Batu Pahat district because of different road conditions, driving habits and environmental of developed driving cycle countries are not same [2][14]. Batu Pahat drive cycle was developed for low-capacity gasoline engine under 150 cc and operating on urban roads, rural roads and road around Universiti Tun Hussein Onn. The importance of these driving cycle as the reference for other research to measure and do automotive simulation regarding fuel consumption and gas emission release from the motorcycle for these three type of driving cycle area. Another use for driving cycles is in vehicle simulations [3]. More specifically, they are used in propulsion system simulations to predict the performance of internal combustion engines, transmissions, electric drive systems, batteries, fuel cell systems, and similar components [18]. Data collection methods used in this study is the use of Global Positioning System (GPS). The results obtained are not similar to each other due to differences in congestion on data taken. From the driving cycle graph obtained, such as the average velocity, maximum velocity, the duration and Positive Acceleration Kinetic Energy (PKE) can be determined. In addition, the best driving cycle sample can be determined from the sum of error calculated. The least sum of error means the best driving cycle

The shock/shear platform for planar radiation-hydrodynamics experiments on the National Ignition Facility

DOE PAGES

Doss, F. W.; Kline, J. L.; Flippo, K. A.; ...

2015-04-17

An indirectly-driven shock tube experiment fielded on the National Ignition Facility (NIF) was used to create a high-energy-density hydrodynamics platform at unprecedented scale. Scaling up a shear-induced mixing experiment previously fielded at OMEGA, the NIF shear platform drives 130 μm/ns shocks into a CH foam-filled shock tube (~ 60 mg/cc) with interior dimensions of 1.5 mm diameter and 5 mm length. The pulse-shaping capabilities of the NIF are used to extend the drive for >10 ns, and the large interior tube volumes are used to isolate physics-altering edge effects from the region of interest. The scaling of the experiment tomore » the NIF allows for considerable improvement in maximum driving time of hydrodynamics, in fidelity of physics under examination, and in diagnostic clarity. Details of the experimental platform and post-shot simulations used in the analysis of the platform-qualifying data are presented. Hydrodynamic scaling is used to compare shear data from OMEGA with that from NIF, suggesting a possible change in the dimensionality of the instability at late times from one platform to the other.« less

Nonlinear mathematical modeling and sensitivity analysis of hydraulic drive unit

NASA Astrophysics Data System (ADS)

Kong, Xiangdong; Yu, Bin; Quan, Lingxiao; Ba, Kaixian; Wu, Liujie

2015-09-01

The previous sensitivity analysis researches are not accurate enough and also have the limited reference value, because those mathematical models are relatively simple and the change of the load and the initial displacement changes of the piston are ignored, even experiment verification is not conducted. Therefore, in view of deficiencies above, a nonlinear mathematical model is established in this paper, including dynamic characteristics of servo valve, nonlinear characteristics of pressure-flow, initial displacement of servo cylinder piston and friction nonlinearity. The transfer function block diagram is built for the hydraulic drive unit closed loop position control, as well as the state equations. Through deriving the time-varying coefficient items matrix and time-varying free items matrix of sensitivity equations respectively, the expression of sensitivity equations based on the nonlinear mathematical model are obtained. According to structure parameters of hydraulic drive unit, working parameters, fluid transmission characteristics and measured friction-velocity curves, the simulation analysis of hydraulic drive unit is completed on the MATLAB/Simulink simulation platform with the displacement step 2 mm, 5 mm and 10 mm, respectively. The simulation results indicate that the developed nonlinear mathematical model is sufficient by comparing the characteristic curves of experimental step response and simulation step response under different constant load. Then, the sensitivity function time-history curves of seventeen parameters are obtained, basing on each state vector time-history curve of step response characteristic. The maximum value of displacement variation percentage and the sum of displacement variation absolute values in the sampling time are both taken as sensitivity indexes. The sensitivity indexes values above are calculated and shown visually in histograms under different working conditions, and change rules are analyzed. Then the sensitivity indexes values of four measurable parameters, such as supply pressure, proportional gain, initial position of servo cylinder piston and load force, are verified experimentally on test platform of hydraulic drive unit, and the experimental research shows that the sensitivity analysis results obtained through simulation are approximate to the test results. This research indicates each parameter sensitivity characteristics of hydraulic drive unit, the performance-affected main parameters and secondary parameters are got under different working conditions, which will provide the theoretical foundation for the control compensation and structure optimization of hydraulic drive unit.

The pattern of the electromagnetic field emitted by mobile phones in motor vehicle driving simulators.

PubMed

Politański, Piotr; Bortkiewicz, Alicja; Zmyślony, Marek

2013-06-01

The paper reports the results of the determinations of UMTS EMF distributions in the driver’s cab of motor vehicle simulators. The results will serve as the basis for future research on the influence of EMF emitted by mobile phones on driver physiology. Two motor vehicle driving simulators were monitored, while an EMF source was placed at the driver's head or on the dashboard of the motor vehicle driving simulator. For every applied configuration, the maximal electric field strength was measured, as were the values at 16 points corresponding to chosen locations on a driver's or passenger's body. When the power was set for the maximum (49 mW), a value of 27 V/m was measured in the vicinity of the driver's head when the phone was close to the head. With the same power, when the phone was placed on the dashboard, the measured maximum was 15.2 V/m in the vicinity of the driver's foot. Similar results were obtained for the passenger. Significant perturbations in EMF distribution and an increase in electric field strength values in the mo-tor vehicle driving simulator were also observed in comparison to free space measurements, and the electric field strength was up to 3 times higher inside the simulator. This study can act as the basis of future studies concerning the influence of the EMF emitted by mobile phones on the physiology of the driver. Additionally, the authors postulate that it is advisable to keep mobile phones at a distance from the head, i.e. use, whenever possible, hands-free kits to reduce EMF exposure, both for drivers and passengers.

Evolutionary History Underlies Plant Physiological Responses to Global Change Since the Last Glacial Maximum

NASA Astrophysics Data System (ADS)

Becklin, K. M.; Medeiros, J. S.; Sale, K. R.; Ward, J. K.

2014-12-01

Assessing family and species-level variation in physiological responses to global change across geologic time is critical for understanding factors that underlie changes in species distributions and community composition. Ancient plant specimens preserved within packrat middens are invaluable in this context since they allow for comparisons between co-occurring plant lineages. Here we used modern and ancient plant specimens preserved within packrat middens from the Snake Range, NV to investigate the physiological responses of a mixed montane conifer community to global change since the last glacial maximum. We used a conceptual model to infer relative changes in stomatal conductance and maximum photosynthetic capacity from measures of leaf carbon isotopes, stomatal characteristics, and leaf nitrogen content. Our results indicate that most of the sampled taxa decreased stomatal conductance and/or photosynthetic capacity from glacial to modern times. However, plant families differed in the timing and magnitude of these physiological responses. Additionally, leaf-level responses were more similar within plant families than within co-occurring species assemblages. This suggests that adaptation at the level of leaf physiology may not be the main determinant of shifts in community composition, and that plant evolutionary history may drive physiological adaptation to global change over recent geologic time.

Work schedules of long-distance truck drivers before and after 2004 hours-of-service rule change.

PubMed

McCartt, Anne T; Hellinga, Laurie A; Solomon, Mark G

2008-01-01

Federal rules regulate work hours of interstate commercial truck drivers. On January 4, 2004, a new work rule was implemented, increasing daily and weekly maximum driving limits and daily off-duty requirements. The present study assessed changes in long-distance truck drivers' reported work schedules and reported fatigued driving after the rule change. Associations between reported rule violations, fatigued driving, and schedule as well as other characteristics were examined. Samples of long-distance truck drivers were interviewed face-to-face in two states immediately before the rule change (November-December 2003) and about 1 year (November-December 2004) and 2 years (November-December 2005) after the change. Drivers reported substantially more hours of driving after the rule change. Most drivers reported regularly using a new restart provision, which permits a substantial increase in weekly driving. Reported daily off-duty and sleep time increased. Reported incidents of falling asleep at the wheel of the truck increased between 2003 (before the rule change) and 2004 and 2005 (after the change); in 2005 about one fifth of drivers reported falling asleep at the wheel in the past month. The frequency of reported rule violations under the old and new rules was similar. The percentage of trucks with electronic on-board recorders increased significantly to almost half the fleet; only a few drivers were using automated recorders to report rule compliance. More than half of drivers said that requiring automated recorders on all large trucks to enforce driving-hour limits would improve compliance with work rules. Based on the 2004-2005 survey data, drivers who reported more frequent rule violations were significantly more likely to report fatigued driving. Predictors of reported violations included having unrealistic delivery schedules, longer wait times to drop off or pick up loads, difficulty finding a legal place to stop or rest, and driving a refrigerated trailer. Reported truck driver fatigue increased after the new rule was implemented, suggesting that the rule change may not have achieved the goal of reducing fatigued driving. Reported violations of the work rules remain common. Because many trucks already have electronic recorders, requiring them as a means of monitoring driving hours appears feasible.

Decrease of dynamic loads in mobile energy means

NASA Astrophysics Data System (ADS)

Polivaev, O. I.; Gorban, L. K.; Vorohobin, A. V.; Vedrinsky, O. S.

2018-03-01

The increase in the productivity of machine and tractor units is possible due to the increase in operating speeds, this leads to the emergence of increased dynamic loads in the system “engine-transmission-propulsion unit-soil”, which worsens the performance of machine-tractor aggregates. To reduce fluctuations in the “engine-transmission” system, special vibration dampers are used, which installed in close proximity to the engine and protect well the transmission from uneven engine operation; however, such dampers practically do not eliminate the oscillations of external loads. Reducing dynamic loads on the transmission and the mobile power engine (MPE) is an important issue directly related to improving the performance, reliability and durability of the tractor, as well as reducing the slippage of the drive wheels. In order to reduce effectively dynamic loads on the transmission and on the MPE, it is necessary to introduce resilient damping elements closer to the sources of oscillations, namely, to the driving wheels. At the same time, the elastic-damping element should provide accumulation of vibration energy caused by external influences and have a large energy capacity. The installation of an elastic-damping element in the final link of the tractor transmission ensures a reduction in the magnitude of external influences, thereby protecting the engine and transmission from large dynamic loads, and allows one to reduce the slippage of the propellers, which has a positive effect on the traction and energy characteristics of the tractor. Traction tests of the LTP-55 tractor on a concrete road showed that the use of an elasto-damping drive makes it possible to increase the maximum tractive power from 33.5 to 35.3 kW and to reduce the slipping of propellers by 12-30%, the specific fuel consumption by 6-10%. When driving on stubble, the use of an elastic-damping drive increases the maximum tractive power from 25 to 26 kW, reduces the skidding of propellers by 10-28%, and the specific fuel consumption by 10-12.5%.

Meissner motor using high-Tc ceramic superconductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takeoka, A.; Ishikawa, A.; Suzuki, M.

1989-03-01

The authors developed a brand new superconducting motor using high-Tc ceramic superconductors for the first time. This motor utilizes the repulsive force caused by the Meissner effect, which appears below Tc and disappears above that, and is therefore referred to as the Meissner Motor. The motor rotated at a maximum speed of 40 rpm. Though the repulsive force to drive the motor increased with the decrease of temperature or the increase of the gradient magnetic field, it was only about 1.1 gf/g at 77 K in 3500 G/cm. The motor has a maximum torque of 5.0 gf-cm theoretically, but actuallymore » had a torque below 0.66 gf-cm, because it took some time to be cooled below Tc. The rotating speed of the motor was limited by heating ability and its torque was limited by cooling ability.« less

Design and simulation of MEMS-actuated adjustable optical wedge for laser beam scanners

NASA Astrophysics Data System (ADS)

Bahgat, Ahmed S.; Zaki, Ahmed H.; Abdo Mohamed, Mohamed; El Sherif, Ashraf Fathy

2018-01-01

This paper introduces both optical and mechanical design and simulation of large static deflection MOEMS actuator. The designed device is in the form of an adjustable optical wedge (AOW) laser scanner. The AOW is formed of 1.5-mm-diameter plano-convex lens separated by air gap from plano-concave fixed lens. The convex lens is actuated by staggered vertical comb drive and suspended by rectangular cross-section torsion beam. An optical analysis and simulation of air separated AOW as well as detailed design, analysis, and static simulation of comb -drive are introduced. The dynamic step response of the full system is also introduced. The analytical solution showed a good agreement with the simulation results. A general global minimum optimization algorithm is applied to the comb-drive design to minimize driving voltage. A maximum comb-drive mechanical deflection angle of 12 deg in each direction was obtained under DC actuation voltage of 32 V with a settling time of 90 ms, leading to 1-mm one-dimensional (1-D) steering of laser beam with continuous optical scan angle of 5 deg in each direction. This optimization process provided a design of larger deflection actuator with smaller driving voltage compared with other conventional devices. This enhancement could lead to better performance of MOEMS-based laser beam scanners for imaging and low-speed applications.

Flying Fast and High: Operational Flight Planning for Maximum Data Return for Airborne Snow Observatory Mountain Surveys

NASA Astrophysics Data System (ADS)

Berisford, D. F.; Painter, T. H.; Richardson, M.; Wallach, A.; Deems, J. S.; Bormann, K. J.

2017-12-01

The Airborne Snow Observatory (ASO - http://aso.jpl.nasa.gov) uses an airborne laser scanner to map snow depth, and imaging spectroscopy to map snow albedo in order to estimate snow water equivalent and melt rate over mountainous, hydrologic basin-scale areas. Optimization of planned flight lines requires the balancing of many competing factors, including flying altitude and speed, bank angle limitation, laser pulse rate and power level, flightline orientation relative to terrain, surface optical properties, and data output requirements. These variables generally distill down to cost vs. higher resolution data. The large terrain elevation variation encountered in mountainous terrain introduces the challenge of narrow swath widths over the ridgetops, which drive tight flightline spacing and possible dropouts over the valleys due to maximum laser range. Many of the basins flown by ASO exceed 3,000m of elevation relief, exacerbating this problem. Additionally, sun angle may drive flightline orientations for higher-quality spectrometer data, which may change depending on time of day. Here we present data from several ASO missions, both operational and experimental, showing the lidar performance and accuracy limitations for a variety of operating parameters. We also discuss flightline planning strategies to maximize data density return per dollar, and a brief analysis on the effect of short turn times/steep bank angles on GPS position accuracy.

MEANS FOR CONTROLLING A NUCLEAR REACTOR

DOEpatents

Wilson, V.C.; Overbeck, W.P.; Slotin, L.; Froman, D.K.

1957-12-17

This patent relates to nuclear reactors of the type using a solid neutron absorbing material as a means for controlling the reproduction ratio of the system and thereby the power output. Elongated rods of neutron absorbing material, such as boron steel for example, are adapted to be inserted and removed from the core of tae reactor by electronic motors and suitable drive means. The motors and drive means are controlled by means responsive to the neutron density, such as ionization chambers. The control system is designed to be responsive also to the rate of change in neutron density to automatically maintain the total power output at a substantially constant predetermined value. A safety rod means responsive to neutron density is also provided for keeping the power output below a predetermined maximum value at all times.

A piezoelectric ultrasonic linear micromotor using a slotted stator.

PubMed

Yun, Cheol-Ho; Watson, Brett; Friend, James; Yeo, Leslie

2010-08-01

A novel ultrasonic micro linear motor that uses 1st longitudinal and 2nd bending modes, derived from a bartype stator with a rectangular slot cut through the stator length, has been proposed and designed for end-effect devices of microrobotics and bio-medical applications. The slot structure plays an important role in the motor design, and can be used not only to tune the resonance frequency of the two vibration modes but also to reduce the undesirable longitudinal coupling displacement caused by bending vibration at the end of the stator. By using finite element analysis, the optimal slot dimension to improve the driving tip motion was determined, resulting in the improvement of the motor performance. The trial linear motor, with a weight of 1.6 g, gave a maximum driving velocity of 1.12 m/s and a maximum driving force of 3.4 N. A maximum mechanical output power of 1.1 W was obtained at force of 1.63 N and velocity of 0.68 m/s. The output mechanical power per unit weight was 688 W/kg.

Roadway backfill method to prevent geohazards induced by room and pillar mining: a case study in Changxing coal mine, China

NASA Astrophysics Data System (ADS)

Zhou, Nan; Li, Meng; Zhang, Jixiong; Gao, Rui

2016-11-01

Coal mines in the western areas of China experience low mining rates and induce many geohazards when using the room and pillar mining method. In this research, we proposed a roadway backfill method during longwall mining to target these problems. We tested the mechanical properties of the backfill materials to determine a reasonable ratio of backfill materials for the driving roadway during longwall mining. We also introduced the roadway layout and the backfill mining technique required for this method. Based on the effects of the abutment stress from a single roadway driving task, we designed the distance between roadways and a driving and filling sequence for multiple-roadway driving. By doing so, we found the movement characteristics of the strata with quadratic stabilization for backfill mining during roadway driving. Based on this research, the driving and filling sequence of the 3101 working face in Changxing coal mine was optimized to avoid the superimposed influence of mining-induced stress. According to the analysis of the surface monitoring data, the accumulated maximum subsidence is 15 mm and the maximum horizontal deformation is 0.8 mm m-1, which indicated that the ground basically had no obvious deformation after the implementation of the roadway backfill method at 3101 working face.

Study of consensus-based time synchronization in wireless sensor networks.

PubMed

He, Jianping; Li, Hao; Chen, Jiming; Cheng, Peng

2014-03-01

Recently, various consensus-based protocols have been developed for time synchronization in wireless sensor networks. However, due to the uncertainties lying in both the hardware fabrication and network communication processes, it is not clear how most of the protocols will perform in real implementations. In order to reduce such gap, this paper investigates whether and how the typical consensus-based time synchronization protocols can tolerate the uncertainties in practical sensor networks through extensive testbed experiments. For two typical protocols, i.e., Average Time Synchronization (ATS) and Maximum Time Synchronization (MTS), we first analyze how the time synchronization accuracy will be affected by various uncertainties in the system. Then, we implement both protocols on our sensor network testbed consisted of Micaz nodes, and investigate the time synchronization performance and robustness under various network settings. Noticing that the synchronized clocks under MTS may be slightly faster than the desirable clock, by adopting both maximum consensus and minimum consensus, we propose a modified protocol, MMTS, which is able to drive the synchronized clocks closer to the desirable clock while maintaining the convergence rate and synchronization accuracy of MTS. © 2013 ISA. Published by ISA. All rights reserved.

Baseline tests of the power-train electric delivery van

NASA Technical Reports Server (NTRS)

Lumannick, S.; Dustin, M. O.; Bozek, J. M.

1977-01-01

Vehicle maximum speed, range at constant speed, range over stop-and-go driving schedules, maximum acceleration, gradeability, gradeability limit, road energy consumption, road power, indicated energy consumption, braking capability, battery charger efficiency, and battery characteristics were determined for a modified utility van powered by sixteen 6-volt batteries connected in series. A chopper controller actuated by a foot accelerator pedal changes the voltage applied to the 22-kilowatt (30-hp) series-wound drive motor. In addition to the conventional hydraulic braking system, the vehicle has hydraulic regenerative braking. Cycle tests and acceleration tests were conducted with and without hydraulic regeneration.

Compensatory plasticity at an identified synapse tunes a visuomotor pathway.

PubMed

Rogers, Stephen M; Krapp, Holger G; Burrows, Malcolm; Matheson, Thomas

2007-04-25

We characterized homeostatic plasticity at an identified sensory-motor synapse in an insect, which maintains constant levels of motor drive as locusts transform from their solitarious phase to their gregarious swarming phase. The same mechanism produces behaviorally relevant changes in response timing that can be understood in the context of an animal's altered behavioral state. For individual animals of either phase, different looming objects elicited different spiking responses in a visual looming detector interneuron, descending contralateral movement detector (DCMD), yet its synaptic drive to a leg motoneuron, fast extensor tibiae (FETi), always had the same maximum amplitude. Gregarious locust DCMDs produced more action potentials and had higher firing frequencies, but individual postsynaptic potentials (PSPs) elicited in FETi were half the amplitude of those in solitarious locusts. A model suggested that this alone could not explain the similarity in overall amplitude, and we show that facilitation increased the maximum compound PSP amplitude in gregarious animals. There was the same linear relationship between times of peak DCMD firing before collision and the size/velocity of looming objects in both phases. The DCMD-FETi synapse transformed this relationship nonlinearly, such that peak amplitudes of compound PSPs occurred disproportionately earlier for smaller/faster objects. Furthermore, the peak PSP amplitude occurred earlier in gregarious than in solitarious locusts, indicating a differential tuning. Homeostatic modulation of the amplitude, together with a nonlinear synaptic transformation of timing, acted together to tune the DCMD-FETi system so that swarming gregarious locusts respond earlier to small moving objects, such as conspecifics, than solitarious locusts.

Event-driven time-optimal control for a class of discontinuous bioreactors.

PubMed

Moreno, Jaime A; Betancur, Manuel J; Buitrón, Germán; Moreno-Andrade, Iván

2006-07-05

Discontinuous bioreactors may be further optimized for processing inhibitory substrates using a convenient fed-batch mode. To do so the filling rate must be controlled in such a way as to push the reaction rate to its maximum value, by increasing the substrate concentration just up to the point where inhibition begins. However, an exact optimal controller requires measuring several variables (e.g., substrate concentrations in the feed and in the tank) and also good model knowledge (e.g., yield and kinetic parameters), requirements rarely satisfied in real applications. An environmentally important case, that exemplifies all these handicaps, is toxicant wastewater treatment. There the lack of online practical pollutant sensors may allow unforeseen high shock loads to be fed to the bioreactor, causing biomass inhibition that slows down the treatment process and, in extreme cases, even renders the biological process useless. In this work an event-driven time-optimal control (ED-TOC) is proposed to circumvent these limitations. We show how to detect a "there is inhibition" event by using some computable function of the available measurements. This event drives the ED-TOC to stop the filling. Later, by detecting the symmetric event, "there is no inhibition," the ED-TOC may restart the filling. A fill-react cycling then maintains the process safely hovering near its maximum reaction rate, allowing a robust and practically time-optimal operation of the bioreactor. An experimental study case of a wastewater treatment process application is presented. There the dissolved oxygen concentration was used to detect the events needed to drive the controller. (c) 2006 Wiley Periodicals, Inc.

Modelling and Simulation in the Design Process of Armored Vehicles

DTIC Science & Technology

2003-03-01

trackway conditions is a demanding optimization task. Basically, a high level of ride comfort requires soft suspension tuning, whereas driving safety relies...The maximum off-road speed is generally limited by traction, input torque, driving safety and ride comfort. When obstacles are to be negotiated, the...wheel travel was defined during the mobility simulation runs. Figure 14: Ramp 1.5m at 40 kph; virtual and physical prototype Driving safety and ride

Parametric tests of a traction drive retrofitted to an automotive gas turbine

NASA Technical Reports Server (NTRS)

Rohn, D. A.; Lowenthal, S. H.; Anderson, N. E.

1980-01-01

The results of a test program to retrofit a high performance fixed ratio Nasvytis Multiroller Traction Drive in place of a helical gear set to a gas turbine engine are presented. Parametric tests up to a maximum engine power turbine speed of 45,500 rpm and to a power level of 11 kW were conducted. Comparisons were made to similar drives that were parametrically tested on a back-to-back test stand. The drive showed good compatibility with the gas turbine engine. Specific fuel consumption of the engine with the traction drive speed reducer installed was comparable to the original helical gearset equipped engine.

Multi-timescale power and energy assessment of lithium-ion battery and supercapacitor hybrid system using extended Kalman filter

NASA Astrophysics Data System (ADS)

Wang, Yujie; Zhang, Xu; Liu, Chang; Pan, Rui; Chen, Zonghai

2018-06-01

The power capability and maximum charge and discharge energy are key indicators for energy management systems, which can help the energy storage devices work in a suitable area and prevent them from over-charging and over-discharging. In this work, a model based power and energy assessment approach is proposed for the lithium-ion battery and supercapacitor hybrid system. The model framework of the lithium-ion battery and supercapacitor hybrid system is developed based on the equivalent circuit model, and the model parameters are identified by regression method. Explicit analyses of the power capability and maximum charge and discharge energy prediction with multiple constraints are elaborated. Subsequently, the extended Kalman filter is employed for on-board power capability and maximum charge and discharge energy prediction to overcome estimation error caused by system disturbance and sensor noise. The charge and discharge power capability, and the maximum charge and discharge energy are quantitatively assessed under both the dynamic stress test and the urban dynamometer driving schedule. The maximum charge and discharge energy prediction of the lithium-ion battery and supercapacitor hybrid system with different time scales are explored and discussed.

Domain wall formation in late-time phase transitions

NASA Technical Reports Server (NTRS)

Kolb, Edward W.; Wang, Yun

1992-01-01

We examine domain wall formulation in late time phase transitions. We find that in the invisible axion domain wall phenomenon, thermal effects alone are insufficient to drive different parts of the disconnected vacuum manifold. This suggests that domain walls do not form unless either there is some supplemental (but perhaps not unreasonable) dynamics to localize the scalar field responsible for the phase transition to the low temperature maximum (to an extraordinary precision) before the onset of the phase transition, or there is some non-thermal mechanism to produce large fluctuations in the scalar field. The fact that domain wall production is not a robust prediction of late time transitions may suggest future directions in model building.

Maximum efficiency of state-space models of nanoscale energy conversion devices

NASA Astrophysics Data System (ADS)

Einax, Mario; Nitzan, Abraham

2016-07-01

The performance of nano-scale energy conversion devices is studied in the framework of state-space models where a device is described by a graph comprising states and transitions between them represented by nodes and links, respectively. Particular segments of this network represent input (driving) and output processes whose properly chosen flux ratio provides the energy conversion efficiency. Simple cyclical graphs yield Carnot efficiency for the maximum conversion yield. We give general proof that opening a link that separate between the two driving segments always leads to reduced efficiency. We illustrate these general result with simple models of a thermoelectric nanodevice and an organic photovoltaic cell. In the latter an intersecting link of the above type corresponds to non-radiative carriers recombination and the reduced maximum efficiency is manifested as a smaller open-circuit voltage.

Maximum efficiency of state-space models of nanoscale energy conversion devices.

PubMed

Einax, Mario; Nitzan, Abraham

2016-07-07

The performance of nano-scale energy conversion devices is studied in the framework of state-space models where a device is described by a graph comprising states and transitions between them represented by nodes and links, respectively. Particular segments of this network represent input (driving) and output processes whose properly chosen flux ratio provides the energy conversion efficiency. Simple cyclical graphs yield Carnot efficiency for the maximum conversion yield. We give general proof that opening a link that separate between the two driving segments always leads to reduced efficiency. We illustrate these general result with simple models of a thermoelectric nanodevice and an organic photovoltaic cell. In the latter an intersecting link of the above type corresponds to non-radiative carriers recombination and the reduced maximum efficiency is manifested as a smaller open-circuit voltage.

Pilot study for quantifying driving characteristics during power wheelchair soccer.

PubMed

Kumar, Amit; Karmarkar, Amol M; Collins, Diane M; Souza, Ana; Oyster, Michelle L; Cooper, Rosemarie; Cooper, Rory A

2012-01-01

This study determined the driving characteristics of wheelchair users during power wheelchair soccer games. Data for this study were collected at the 28th and 29th National Veterans Wheelchair Games. Nineteen veterans who were 18 years or older and power wheelchair soccer players completed a brief demographic survey and provided information about their power wheelchairs. A customized data-logging device was placed on each participant's wheelchair before power soccer game participation. The data logger was removed at the end of the final game for each participant. The average distance traveled during the games was 899.5 +/- 592.5 m, and the average maximum continuous distance traveled was 256.0 +/- 209.4 m. The average wheelchair speed was 0.8 +/- 0.2 m/s, and the average duration of driving time was 17.6 +/- 8.3 min. Average proportion of time spent at a speed >1 m/s was 30.7% +/- 33.8%, between 0.5 and 1 m/s was 16.2% +/- 34.4%, and <0.5 m/s was 21.4% +/- 24.3%. The information from this descriptive study provides insight for future research in the field of adapted sports for people with high levels of impairments who use power wheelchairs for their mobility.

High-energy electron emission from metallic nano-tips driven by intense single-cycle terahertz pulses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Sha; Jones, R. R.

Electrons ejected from atoms and subsequently driven to high energies in strong laser fields enable techniques from attosecond pulse generation to imaging with rescattered electrons. Analogous processes govern strong-field electron emission from nanostructures, where long wavelength radiation and large local field enhancements hold the promise for producing electrons with substantially higher energies, allowing for higher resolution time-resolved imaging. Here we report on the use of single-cycle terahertz pulses to drive electron emission from unbiased nano-tips. Energies exceeding 5 keV are observed, substantially greater than previously attained at higher drive frequencies. Despite large differences in the magnitude of the respective localmore » fields, we find that the maximum electron energies are only weakly dependent on the tip radius, for 10 nm« less

High-energy electron emission from metallic nano-tips driven by intense single-cycle terahertz pulses

DOE PAGES

Li, Sha; Jones, R. R.

2016-11-10

Electrons ejected from atoms and subsequently driven to high energies in strong laser fields enable techniques from attosecond pulse generation to imaging with rescattered electrons. Analogous processes govern strong-field electron emission from nanostructures, where long wavelength radiation and large local field enhancements hold the promise for producing electrons with substantially higher energies, allowing for higher resolution time-resolved imaging. Here we report on the use of single-cycle terahertz pulses to drive electron emission from unbiased nano-tips. Energies exceeding 5 keV are observed, substantially greater than previously attained at higher drive frequencies. Despite large differences in the magnitude of the respective localmore » fields, we find that the maximum electron energies are only weakly dependent on the tip radius, for 10 nm« less

49 CFR 398.4 - Driving of motor vehicles.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 5 2013-10-01 2013-10-01 false Driving of motor vehicles. 398.4 Section 398.4... his/her ability or alertness is so impaired through fatigue, illness, or any other cause as to make it... result of the displacement or falling of such articles. (5) Maximum passengers on motor vehicles. No...

49 CFR 398.4 - Driving of motor vehicles.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 5 2010-10-01 2010-10-01 false Driving of motor vehicles. 398.4 Section 398.4... his/her ability or alertness is so impaired through fatigue, illness, or any other cause as to make it... result of the displacement or falling of such articles. (5) Maximum passengers on motor vehicles. No...

49 CFR 398.4 - Driving of motor vehicles.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 5 2012-10-01 2012-10-01 false Driving of motor vehicles. 398.4 Section 398.4... his/her ability or alertness is so impaired through fatigue, illness, or any other cause as to make it... result of the displacement or falling of such articles. (5) Maximum passengers on motor vehicles. No...

49 CFR 398.4 - Driving of motor vehicles.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 5 2014-10-01 2014-10-01 false Driving of motor vehicles. 398.4 Section 398.4... his/her ability or alertness is so impaired through fatigue, illness, or any other cause as to make it... result of the displacement or falling of such articles. (5) Maximum passengers on motor vehicles. No...

49 CFR 398.4 - Driving of motor vehicles.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 5 2011-10-01 2011-10-01 false Driving of motor vehicles. 398.4 Section 398.4... his/her ability or alertness is so impaired through fatigue, illness, or any other cause as to make it... result of the displacement or falling of such articles. (5) Maximum passengers on motor vehicles. No...

Thermal stability control system of photo-elastic interferometer in the PEM-FTs

NASA Astrophysics Data System (ADS)

Zhang, M. J.; Jing, N.; Li, K. W.; Wang, Z. B.

2018-01-01

A drifting model for the resonant frequency and retardation amplitude of a photo-elastic modulator (PEM) in the photo-elastic modulated Fourier transform spectrometer (PEM-FTs) is presented. A multi-parameter broadband-matching driving control method is proposed to improve the thermal stability of the PEM interferometer. The automatically frequency-modulated technology of the driving signal based on digital phase-locked technology is used to track the PEM's changing resonant frequency. Simultaneously the maximum optical-path-difference of a laser's interferogram is measured to adjust the amplitude of the PEM's driving signal so that the spectral resolution is stable. In the experiment, the multi-parameter broadband-matching control method is applied to the driving control system of the PEM-FTs. Control of resonant frequency and retardation amplitude stabilizes the maximum optical-path-difference to approximately 236 μm and results in a spectral resolution of 42 cm-1. This corresponds to a relative error smaller than 2.16% (4.28 standard deviation). The experiment shows that the method can effectively stabilize the spectral resolution of the PEM-FTs.

Autonomous satellite navigation with the Global Positioning System

NASA Technical Reports Server (NTRS)

Fuchs, A. J.; Wooden, W. H., II; Long, A. C.

1977-01-01

This paper discusses the potential of using the Global Positioning System (GPS) to provide autonomous navigation capability to NASA satellites in the 1980 era. Some of the driving forces motivating autonomous navigation are presented. These include such factors as advances in attitude control systems, onboard science annotation, and onboard gridding of imaging data. Simulation results which demonstrate baseline orbit determination accuracies using GPS data on Seasat, Landsat-D, and the Solar Maximum Mission are presented. Emphasis is placed on identifying error sources such as GPS time, GPS ephemeris, user timing biases, and user orbit dynamics, and in a parametric sense on evaluating their contribution to the orbit determination accuracies.

A toy model that predicts the qualitative role of bar bend in a push jerk.

PubMed

Santos, Aaron; Meltzer, Norman E

2009-11-01

In this work, we describe a simple coarse-grained model of a barbell that can be used to determine the qualitative role of bar bend during a jerk. In simulations of this model, we observed a narrow time window during which the lifter can leverage the elasticity of the bar in order to lift the weight to a maximal height. This time window shifted to later times as the weight was increased. In addition, we found that the optimal time to initiate the drive was strongly correlated with the time at which the bar had reached a maximum upward velocity after recoiling. By isolating the effect of the bar, we obtained a generalized strategy for lifting heavy weight in the jerk.

Driver kinematic and muscle responses in braking events with standard and reversible pre-tensioned restraints: validation data for human models.

PubMed

Osth, Jonas; Olafsdóttir, Jóna Marín; Davidsson, Johan; Brolin, Karin

2013-11-01

The objectives of this study are to generate validation data for human models intended for simulation of occupant kinematics in a pre-crash phase, and to evaluate the effect of an integrated safety system on driver kinematics and muscle responses. Eleven male and nine female volunteers, driving a passenger car on ordinary roads, performed maximum voluntary braking; they were also subjected to autonomous braking events with both standard and reversible pre-tensioned restraints. Kinematic data was acquired through film analysis, and surface electromyography (EMG) was recorded bilaterally for muscles in the neck, the upper extremities, and lumbar region. Maximum voluntary contractions (MVCs) were carried out in a driving posture for normalization of the EMG. Seat belt positions, interaction forces, and seat indentions were measured. During normal driving, all muscle activity was below 5% of MVC for females and 9% for males. The range of activity during steady state braking for males and females was 13-44% in the cervical and lumbar extensors, while antagonistic muscles showed a co-contraction of 2.3-19%. Seat belt pre-tension affects both the kinematic and muscle responses of drivers. In autonomous braking with standard restraints, muscle activation occurred in response to the inertial load. With pre-tensioned seat belts, EMG onset occurred earlier; between 71 ms and 176 ms after belt pre-tension. The EMG onset times decreased with repeated trials and were shorter for females than for males. With the results from this study, further improvement and validation of human models that incorporate active musculature will be made possible.

Ellipticity dependence of the near-threshold harmonics of H2 in an elliptical strong laser field.

PubMed

Yang, Hua; Liu, Peng; Li, Ruxin; Xu, Zhizhan

2013-11-18

We study the ellipticity dependence of the near-threshold (NT) harmonics of pre-aligned H2 molecules using the time-dependent density functional theory. The anomalous maximum appearing at a non-zero ellipticity for the generated NT harmonics can be attributed to multiphoton effects of the orthogonally polarized component of the elliptical driving laser field. Our calculation also shows that the structure of the bound-state, such as molecular alignment and bond length, can be sensitively reflected on the ellipticity dependence of the near-threshold harmonics.

A review of passive thermal management of LED module

NASA Astrophysics Data System (ADS)

Huaiyu, Ye; Koh, Sau; van Zeijl, Henk; Gielen, A. W. J.; Guoqi, Zhang

2011-01-01

Recently, the high-brightness LEDs have begun to be designed for illumination application. The increased electrical currents used to drive LEDs lead to thermal issues. Thermal management for LED module is a key design parameter as high operation temperature directly affects their maximum light output, quality, reliability and life time. In this review, only passive thermal solutions used on LED module will be studied. Moreover, new thermal interface materials and passive thermal solutions applied on electronic equipments are discussed which have high potential to enhance the thermal performance of LED Module.

Preshot Predictions for Defect Induced Mix (DIME) Capsules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bradley, Paul A.; Krasheninnikova, Natalia S.; Tregillis, Ian L.

2012-07-31

In this memo, we evaluate the most probable yield and other results for the Defect Induced Mix (DIME-12A) Polar Direct Drive (PDD) capsule-only shots. We evaluate the expected yield, bang time, burn averaged ion temperature, and the average electron temperature of the Ge line-emitting region. We also include synthetic images of the capsule backlit by Cu K-{alpha} emission (8.39 keV) and core self-emission synthetic images. This memo is a companion to the maximum credible yield memo (LA-UR-12-00287) published earlier.

Design and Implementation of the PALM-3000 Real-Time Control System

NASA Technical Reports Server (NTRS)

Truong, Tuan N.; Bouchez, Antonin H.; Burruss, Rick S.; Dekany, Richard G.; Guiwits, Stephen R.; Roberts, Jennifer E.; Shelton, Jean C.; Troy, Mitchell

2012-01-01

This paper reflects, from a computational perspective, on the experience gathered in designing and implementing realtime control of the PALM-3000 adaptive optics system currently in operation at the Palomar Observatory. We review the algorithms that serve as functional requirements driving the architecture developed, and describe key design issues and solutions that contributed to the system's low compute-latency. Additionally, we describe an implementation of dense matrix-vector-multiplication for wavefront reconstruction that exceeds 95% of the maximum sustained achievable bandwidth on NVIDIA Geforce 8800GTX GPU.

HORMONE STUDIES WITH THE ULTRACENTRIFUGE : I. AN IMPROVED AIR-DRIVEN VACUUM ULTRACENTRIFUGE SUITABLE FOR CONCENTRATION WORK IN BIOLOGICAL EXPERIMENTS.

PubMed

Chiles, J A; Severinghaus, A E

1938-06-30

1. An ultracentrifuge is described in which the rotor is driven by a compressed air turbine, and is spun in an evacuated chamber to minimize friction and heating. The rotating parts are supported by a cushion of air in an air bearing. 2. The centrifuge rotor holds 10 test tubes inclined at 45 degrees to the axis, and has a capacity of 55 cc. It is operated at a maximum speed of 51,000 R.P.M., which develops at the top of the fluid column in the test tubes a centrifugal field of over 100,000 times gravity, and at the bottom of the fluid column a field of over 200,000 times gravity. 3. By means of a reverse turbine, the rotor can be brought to a stop from full speed in a relatively short time. 4. A precession damping device is described, which effectively damps the precession and wobbling of the rotor that usually occurs at certain speeds in machines of this type. 5. A relatively long section of shaft is used between the centrifuge rotor and lower bearings. This prevents vibrations from being appreciably transmitted through the shaft to the lower bearings and driving mechanism, and results in a negligible wear on the bearings. 6. The driving mechanism is designed so that the positions of its parts are adjustable, and so that the driving mechanism may be dismantled without disturbing these adjustments.

Older drivers and rapid deceleration events: Salisbury Eye Evaluation Driving Study.

PubMed

Keay, Lisa; Munoz, Beatriz; Duncan, Donald D; Hahn, Daniel; Baldwin, Kevin; Turano, Kathleen A; Munro, Cynthia A; Bandeen-Roche, Karen; West, Sheila K

2013-09-01

Drivers who rapidly change speed while driving may be more at risk for a crash. We sought to determine the relationship of demographic, vision, and cognitive variables with episodes of rapid decelerations during five days of normal driving in a cohort of older drivers. In the Salisbury Eye Evaluation Driving Study, 1425 older drivers aged 67-87 were recruited from the Maryland Motor Vehicle Administration's rolls for licensees in Salisbury, Maryland. Participants had several measures of vision tested: visual acuity, contrast sensitivity, visual fields, and the attentional visual field. Participants were also tested for various domains of cognitive function including executive function, attention, psychomotor speed, and visual search. A custom created driving monitoring system (DMS) was used to capture rapid deceleration events (RDEs), defined as at least 350 milli-g deceleration, during a five day period of monitoring. The rate of RDE per mile driven was modeled using a negative binomial regression model with an offset of the logarithm of the number of miles driven. We found that 30% of older drivers had one or more RDE during a five day period, and of those, about 1/3 had four or more. The rate of RDE per mile driven was highest for those drivers driving<59 miles during the 5-day period of monitoring. However, older drivers with RDE's were more likely to have better scores in cognitive tests of psychomotor speed and visual search, and have faster brake reaction time. Further, greater average speed and maximum speed per driving segment was protective against RDE events. In conclusion, contrary to our hypothesis, older drivers who perform rapid decelerations tend to be more "fit", with better measures of vision and cognition compared to those who do not have events of rapid deceleration. Copyright © 2012 Elsevier Ltd. All rights reserved.

Older Drivers and Rapid Deceleration Events: Salisbury Eye Evaluation Driving Study

PubMed Central

Keay, Lisa; Munoz, Beatriz; Duncan, Donald D; Hahn, Daniel; Baldwin, Kevin; Turano, Kathleen A; Munro, Cynthia A; Bandeen-Roche, Karen; West, Sheila K

2012-01-01

Drivers who rapidly change speed while driving may be more at risk for a crash. We sought to determine the relationship of demographic, vision, and cognitive variables with episodes of rapid decelerations during five days of normal driving in a cohort of older drivers. In the Salisbury Eye Evaluation Driving Study, 1425 older drivers ages 67 to 87 were recruited from the Maryland Motor Vehicle Administration’s rolls for licensees in Salisbury, Maryland. Participants had several measures of vision tested: visual acuity, contrast sensitivity, visual fields, and the attentional visual field. Participants were also tested for various domains of cognitive function including executive function, attention, psychomotor speed, and visual search. A custom created Driving Monitor System (DMS) was used to capture rapid deceleration events (RDE), defined as at least 350 milli-g deceleration, during a five day period of monitoring. The rate of RDE per mile driven was modeled using a negative binomial regression model with an offset of the logarithm of the number of miles driven. We found that 30% of older drivers had one or more RDE during a five day period, and of those, about 1/3 had four or more. The rate of RDE per mile driven was highest for those drivers driving <59 miles during the 5-day period of monitoring. However, older drivers with RDE’s were more likely to have better scores in cognitive tests of psychomotor speed and visual search, and have faster brake reaction time. Further, greater average speed and maximum speed per driving segment was protective against RDE events. In conclusion, contrary to our hypothesis, older drivers who perform rapid decelerations tend to be more “fit”, with better measures of vision and cognition compared to those who do not have events of rapid deceleration. PMID:22742775

Longitudinal-bending mode micromotor using multilayer piezoelectric actuator.

PubMed

Yao, K; Koc, B; Uchino, K

2001-07-01

Longitudinal-bending mode ultrasonic motors with a diameter of 3 mm were fabricated using stacked multilayer piezoelectric actuators, which were self-developed from hard lead zirconate titanate (PZT) ceramic. A bending vibration was converted from a longitudinal vibration with a longitudinal-bending coupler. The motors could be bidirectionally operated by changing driving frequency. Their starting and braking torque were analyzed based on the transient velocity response. With a load of moment of inertia 2.5 x 10(-7) kgm2, the motor showed a maximum starting torque of 127.5 microNm. The braking torque proved to be a constant independent on the motor's driving conditions and was roughly equivalent to the maximum starting torque achievable with our micromotors.

Spectral gain profile of a multi-stack terahertz quantum cascade laser

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bachmann, D., E-mail: dominic.bachmann@tuwien.ac.at; Deutsch, C.; Krall, M.

2014-11-03

The spectral gain of a multi-stack terahertz quantum cascade laser, composed of three active regions with emission frequencies centered at 2.3, 2.7, and 3.0 THz, is studied as a function of driving current and temperature using terahertz time-domain spectroscopy. The optical gain associated with the particular quantum cascade stacks clamps at different driving currents and saturates to different values. We attribute these observations to varying pumping efficiencies of the respective upper laser states and to frequency dependent optical losses. The multi-stack active region exhibits a spectral gain full width at half-maximum of 1.1 THz. Bandwidth and spectral position of themore » measured gain match with the broadband laser emission. As the laser action ceases with increasing operating temperature, the gain at the dominant lasing frequency of 2.65 THz degrades sharply.« less

An analysis of cumulative risks based on biomonitoring data for six phthalates using the Maximum Cumulative Ratio

EPA Science Inventory

The Maximum Cumulative Ratio (MCR) quantifies the degree to which a single chemical drives the cumulative risk of an individual exposed to multiple chemicals. Phthalates are a class of chemicals with ubiquitous exposures in the general population that have the potential to cause ...

Design and experiments of a linear piezoelectric motor driven by a single mode.

PubMed

Liu, Zhen; Yao, Zhiyuan; Li, Xiang; Fu, Qianwei

2016-11-01

In this contribution, we propose a novel linear piezoelectric motor with a compact stator that is driven by a single mode. The linear piezoelectric motor can realize bidirectional motion by changing the vibration modes of the stator. Finite element analysis is performed to determine the required vibration mode of the stator and obtain the optimal stator structure and dimensions. Furthermore, the trajectories of the driving foot are analyzed with and without consideration of the mechanical contact with the slider. It is shown that the trajectory of the driving foot is an oblique line when disregarding the contact, and the trajectory becomes an oblique ellipse while taking into account the contact. Finally, a prototype of the motor is fabricated based on the results of finite element analysis. The optimization results show that the motor reaches its maximum thrust force of 4.0 kg, maximum thrust-weight ratio of 33.3, maximum unloaded velocity of 385 mm/s under the excitation of Mode-B, and maximum unloaded velocity of 315 mm/s under the excitation of Mode-L.

Cascading of Fluctuations in Interdependent Energy Infrastructures. Gas-Grid Coupling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chertkov, Michael; Lebedev, Vladimir; Backhaus, Scott N.

2014-09-05

The revolution of hydraulic fracturing has dramatically increased the supply and lowered the cost of natural gas in the United States driving an expansion of natural gas-fired generation capacity in many electrical grids. Unrelated to the natural gas expansion, lower capital costs and renewable portfolio standards are driving an expansion of intermittent renewable generation capacity such as wind and photovoltaic generation. These two changes may potentially combine to create new threats to the reliability of these interdependent energy infrastructures. Natural gas-fired generators are often used to balance the fluctuating output of wind generation. However, the time-varying output of these generatorsmore » results in time-varying natural gas burn rates that impact the pressure in interstate transmission pipelines. Fluctuating pressure impacts the reliability of natural gas deliveries to those same generators and the safety of pipeline operations. We adopt a partial differential equation model of natural gas pipelines and use this model to explore the effect of intermittent wind generation on the fluctuations of pressure in natural gas pipelines. The mean square pressure fluctuations are found to grow linearly in time with points of maximum deviation occurring at the locations of flow reversals.« less

Experiments Using Local Helicity Injectors in the Lower Divertor Region as the Majority Current Drive in a Tokamak Plasma

NASA Astrophysics Data System (ADS)

Perry, Justin M.

Local helicity injection (LHI) is a non-solenoidal current drive capable of achieving high-Ip tokamak startup with a relatively compact and non-invasive array of current injectors in the plasma scrape-off layer. The choice of injector location within the edge region is flexible, but has a profound influence on the nature of the current drive in LHI discharges. Past experiments on the Pegasus ST with injection on the low-field-side near the outboard midplane produced plasmas dominated by inductive drive resulting primarily from plasma geometry evolution over the discharge. Recent experiments with injection on the high-field- side in the lower divertor region produce plasmas dominated by helicity injection current drive, with relatively static plasma geometry, and thus negligible inductive drive. Plasma current up to 200 kA is driven with helicity injection as the dominant current drive using a pair of 4 cm2 area injectors sourcing 8 kA of total injected current. Steady sustainment with LHI current drive alone is demonstrated, with 100 kA sustained for 18 ms. Maximum achievable plasma current is found to scale approximately linearly with a plasma-geometry- normalized form of the effective loop voltage from LHI, Vnorm = AinjVinj/Rinj, where A inj is the total injector area, Vinj is the injector bias voltage, and Rinj is the major radius of the injectors. A newly-discovered MHD regime for LHI-driven plasmas is described, in which the large-amplitude n = 1 fluctuations at 20-50 kHz which are generally dominant during LHI are abruptly reduced by an order of magnitude on the outboard side. High frequency fluctuations ( f > 400 kHz) increase inside the plasma edge at the same time. This regime results in improved plasma current and pervasive changes to plasma behavior, and may suggest short wavelength turbulence as a current drive mechanism during LHI.

Understanding resonance graphs using Easy Java Simulations (EJS) and why we use EJS

NASA Astrophysics Data System (ADS)

Wee, Loo Kang; Lee, Tat Leong; Chew, Charles; Wong, Darren; Tan, Samuel

2015-03-01

This paper reports a computer model simulation created using Easy Java Simulation (EJS) for learners to visualize how the steady-state amplitude of a driven oscillating system varies with the frequency of the periodic driving force. The simulation shows (N = 100) identical spring-mass systems being subjected to (1) a periodic driving force of equal amplitude but different driving frequencies, and (2) different amounts of damping. The simulation aims to create a visually intuitive way of understanding how the series of amplitude versus driving frequency graphs are obtained by showing how the displacement of the system changes over time as it transits from the transient to the steady state. A suggested ‘how to use’ the model is added to help educators and students in their teaching and learning, where we explain the theoretical steady-state equation time conditions when the model begins to allow data recording of maximum amplitudes to closely match the theoretical equation, and the steps to collect different runs of the degree of damping. We also discuss two of the design features in our computer model: displaying the instantaneous oscillation together with the achieved steady-state amplitudes, and the explicit world view overlay with scientific representation with different degrees of damping runs. Three advantages of using EJS include: (1) open source codes and creative commons attribution licenses for scaling up of interactively engaging educational practices; (2) the models made can run on almost any device, including Android and iOS; and (3) it allows the redefinition of physics educational practices through computer modeling.

Oscillating field current drive experiments in the Madison Symmetric Torus

NASA Astrophysics Data System (ADS)

Blair, Arthur P., Jr.

Oscillating Field Current Drive (OFCD) is an inductive current drive method for toroidal pinches. To test OFCD, two 280 Hz 2 MVA oscillators were installed in the toroidal and poloidal magnetic field circuits of the Madison Symmetric Torus (MST) Reversed Field Pinch (RFP.) Partial sustainment experiments were conducted where the two voltage oscillations were superimposed on the standard MST power supplies. Supplementary current drive of about 10% has been demonstrated, comparable to theoretical predictions. However, maximum current drive does not coincide with maximum helicity injection rate - possibly due to an observed dependence of core and edge tearing modes on the relative phase of the oscillators. A dependence of wall interactions on phase was also observed, the largest interaction coinciding with negative current drive. Experiments were conducted at 280 and 530 Hz. 530 Hz proved to be too high and yielded little or no net current drive. Experiments at 280 Hz proved more fruitful. A 1D relaxed state model was used to predict the effects of voltage amplitudes, frequencies, and waveforms on performance and to optimize the design of OFCD hardware. Predicted current drive was comparable to experimental values, though the aforementioned phase dependence was not. Comparisons were also made with a more comprehensive 3D model which proved to be a more accurate predictor of current drive. Both 1D and 3D models predicted the feasability of full sustainment via OFCD. Experiments were also conducted with only the toroidal field oscillator applied. An entrainment of the natural sawtooth frequency to our applied oscillation was observed as well as a slow modulation of the edge tearing mode amplitudes. A large modulation (20 to 80 eV) of the ion temperature was also observed that can be partially accounted for by collisional heating via magnetic pumping. Work is in progress to increase the power of the existing OFCD hardware.

Validation of an electronic device for measuring driving exposure.

PubMed

Huebner, Kyla D; Porter, Michelle M; Marshall, Shawn C

2006-03-01

This study sought to evaluate an on-board diagnostic system (CarChip) for collecting driving exposure data in older drivers. Drivers (N = 20) aged 60 to 86 years from Winnipeg and surrounding communities participated. Information on driving exposure was obtained via the CarChip and global positioning system (GPS) technology on a driving course, and obtained via the CarChip and surveys over a week of driving. Velocities and distances were measured over the road course to validate the accuracy of the CarChip compared to GPS for those parameters. The results show that the CarChip does provide valid distance measurements and slightly lower maximum velocities than GPS measures. From the results obtained in this study, it was determined that retrospective self-reports of weekly driving distances are inaccurate. Therefore, an on-board diagnostic system (OBDII) electronic device like the CarChip can provide valid and detailed information about driving exposure that would be useful for studies of crash rates or driving behavior.

Programmable controller system for wind tunnel diversion vanes

NASA Technical Reports Server (NTRS)

King, R. F.

1982-01-01

A programmable controller (PC) system automatic sequence control, which acts as a supervisory controller for the servos, selects the proper drives, and automatically sequences the vanes, was developed for use in a subsonic wind tunnel. Tunnel modifications include a new second test section (80 ft x 100 ft with a maximum air speed capability of 110 knots) and an increase in maximum velocity flow from 200 knots to 300 knots. A completely automatic sequence control is necessary in order to allow intricate motion of the 14 triangularly arranged vanes which can be as large as 70 ft high x 35 ft wide and which require precise acceleration and deceleration control. Rate servos on each drive aid in this control, and servo cost was minimized by using four silicon controlled rectifier controllers to control the 20 dc drives. The PC has a programming capacity which facilitated the implementation of extensive logic design. A series of diagrams sequencing the vanes and a block diagram of the system are included.

Development of an ultrasonic linear motor with ultra-positioning capability and four driving feet.

PubMed

Zhu, Cong; Chu, Xiangcheng; Yuan, Songmei; Zhong, Zuojin; Zhao, Yanqiang; Gao, Shuning

2016-12-01

This paper presents a novel linear piezoelectric motor which is suitable for rapid ultra-precision positioning. The finite element analysis (FEA) was applied for optimal design and further analysis, then experiments were conducted to investigate its performance. By changing the input signal, the proposed motor was found capable of working in the fast driving mode as well as in the precision positioning mode. When working in the fast driving mode, the motor acts as an ultrasonic motor with maximum no-load speed up to 181.2mm/s and maximum thrust of 1.7N at 200Vp-p. Also, when working in precision positioning mode, the motor can be regarded as a flexible hinge piezoelectric actuator with arbitrary motion in the range of 8μm. The measurable minimum output displacement was found to be 0.08μm, but theoretically, can be even smaller. More importantly, the motor can be quickly and accurately positioned in a large stroke. Copyright © 2016 Elsevier B.V. All rights reserved.

Response of genioglossus muscle to increasing chemical drive in sleeping obstructive apnea patients.

PubMed

Loewen, Andrea H S; Ostrowski, Michele; Laprairie, John; Maturino, Frances; Hanly, Patrick J; Younes, Magdy

2011-08-01

Subjects with a collapsible upper airway must activate their pharyngeal dilators sufficiently in response to increasing chemical drive if they are to maintain airway patency without arousal from sleep. Little is known about the response of pharyngeal dilators to increasing chemical drive in these subjects. We wished to determine, in obstructive apnea patients, the response of the genioglossus to increasing chemical drive and the contribution of mechanoreceptor feedback to this response. Physiological study. University-based sleep laboratory. 20 patients with obstructive apnea. Genioglossus activity was monitored during overnight polysomnography on optimal continuous positive airway pressure (CPAP). Intermittently, inspired gases were altered to produce different levels of ventilatory stimulation. CPAP was then briefly reduced to 1.0 cm H(2)O (dial-down), inducing an obstruction. Without mechanoreceptor feedback (i.e., on CPAP) the increase in genioglossus activity as ventilation increased from 6.1 ± 1.4 to 16.1 ± 4.8 L/min was modest (ΔTonic activity 0.3% ± 0.5%maximum; ΔPhasic activity 1.7% ± 3.4%maximum). Genioglossus activity increased immediately upon dial-down, reflecting mechanoreceptor feedback, but only when ventilation before dial-down exceeded a threshold value. This threshold varied among patients and, once surpassed, genioglossus activity increased briskly with further increases in chemical drive (1.1% ± 0.84%GG(MAX) per L/min increase in V(E)). In sleeping obstructive apnea patients: (1) Mechanoreceptor feedback is responsible for most of the genioglossus response to chemical drive. (2) Mechanoreceptor feedback is effective only above a threshold chemical drive, which varies greatly among patients. These findings account in part for the highly variable relation between pharyngeal mechanical abnormalities and apnea severity.

An Analysis of Cumulative Risks Indicated by Biomonitoring Data of Six Phthalates Using the Maximum Cumulative Ratio

EPA Science Inventory

The Maximum Cumulative Ratio (MCR) quantifies the degree to which a single component of a chemical mixture drives the cumulative risk of a receptor.1 This study used the MCR, the Hazard Index (HI) and Hazard Quotient (HQ) to evaluate co-exposures to six phthalates using biomonito...

Evaluation of the Evidence Base for the Alcohol Industry's Actions to Reduce Drink Driving Globally.

PubMed

Esser, Marissa B; Bao, James; Jernigan, David H; Hyder, Adnan A

2016-04-01

To evaluate the evidence base for the content of initiatives that the alcohol industry implemented to reduce drink driving from 1982 to May 2015. We systematically analyzed the content of 266 global initiatives that the alcohol industry has categorized as actions to reduce drink driving. Social aspects public relations organizations (i.e., organizations funded by the alcohol industry to handle issues that may be damaging to the business) sponsored the greatest proportion of the actions. Only 0.8% (n = 2) of the sampled industry actions were consistent with public health evidence of effectiveness for reducing drink driving. The vast majority of the alcohol industry's actions to reduce drink driving does not reflect public health evidenced-based recommendations, even though effective drink-driving countermeasures exist, such as a maximum blood alcohol concentration limit of 0.05 grams per deciliter for drivers and widespread use of sobriety checkpoints.

Two optimal working regimes of the ”long” Iguasu gas centrifuge

NASA Astrophysics Data System (ADS)

Borman, V. D.; Bogovalov, S. V.; Borisevich, V. D.; Tronin, I. V.; Tronin, V. N.

2016-09-01

We argue on the basis of the results of optimization calculations that the dependence of the optimal separative power of the Iguasu gas centrifuge with 2 m rotor has two local maxima,corresponding pressures of p max1 = 35 mmHg and p max2 = 350 mmHg. The optimal separative power values in these maxima differ by the value of 0.6%. Low pressure maximum is caused by the thermal drive, whereas high pressure maximum is caused by both thermal and mechanical drives. High pressure maximum is located on wide ’’plateau” from p 1 = 200 mmHg to p 2 = 500 mmHg, where the optimal separative power changes in the range of 0.7%. In this way, Iguasu gas centrifuge has two optimal working regimes with different sets of working parameters and close slightly different values of the separative power. Calculations show that high pressure regime is less sensitive to the parameters change than low pressure one.

Parameter Optimization and Operating Strategy of a TEG System for Railway Vehicles

NASA Astrophysics Data System (ADS)

Heghmanns, A.; Wilbrecht, S.; Beitelschmidt, M.; Geradts, K.

2016-03-01

A thermoelectric generator (TEG) system demonstrator for diesel electric locomotives with the objective of reducing the mechanical load on the thermoelectric modules (TEM) is developed and constructed to validate a one-dimensional thermo-fluid flow simulation model. The model is in good agreement with the measurements and basis for the optimization of the TEG's geometry by a genetic multi objective algorithm. The best solution has a maximum power output of approx. 2.7 kW and does not exceed the maximum back pressure of the diesel engine nor the maximum TEM hot side temperature. To maximize the reduction of the fuel consumption, an operating strategy regarding the system power output for the TEG system is developed. Finally, the potential consumption reduction in passenger and freight traffic operating modes is estimated under realistic driving conditions by means of a power train and lateral dynamics model. The fuel savings are between 0.5% and 0.7%, depending on the driving style.

Browns Ferry Nuclear Plant Unit 2: Control rod drive scram discharge headers decontamination effort

DOE Office of Scientific and Technical Information (OSTI.GOV)

Traynor, J.C.

1983-08-01

The control rod drive (CRD) scram discharge headers were decontaminated during the Browns Ferry unit 2, cycle 4 refueling outage (August 2-5, 1982). Hydrolasing (high-pressure water blasting) was used as the method of decontamination to remove fixed and loose radioactive contaminants from the headers. It was found that hydrolasing of the west scram discharge headers resulted in approximate maximum and average decontamination factors (DFs) on contact of 13 and 5, respectively. For the east scram discharge headers, hydrolasing resulted in a maximum and average DF on contact of approximately 3. The maximum and average DFs on contact for the individualmore » headers ranged from 1 to 33 and 1 to 10, respectively, while the walkway (head-level) DFs were in the range of 3 to 4. Higher DFs were impeded by inadequate drainage and backwashing of fluid. This led to increased radiation levels in some areas and recontamination of adjacent headers.« less

Losses in chopper-controlled DC series motors

NASA Technical Reports Server (NTRS)

Hamilton, H. B.

1982-01-01

Motors for electric vehicle (EV) applications must have different features than dc motors designed for industrial applications. The EV motor application is characterized by the following requirements: (1) the need for highest possible efficiency from light load to overload, for maximum EV range, (2) large short time overload capability (The ratio of peak to average power varies from 5/1 in heavy city traffic to 3/1 in suburban driving situations) and (3) operation from power supply voltage levels of 84 to 144 volts (probably 120 volts maximum). A test facility utilizing a dc generator as a substitute for a battery pack was designed and utilized. Criteria for the design of such a facility are presented. Two motors, differing in design detail, commercially available for EV use were tested. Losses measured are discussed, as are waves forms and their harmonic content, the measurements of resistance and inductance, EV motor/chopper application criteria, and motor design considerations.

Tomography of the fast electron bremsstrahlung emission during lower hybrid current drive on TORE SUPRA

NASA Astrophysics Data System (ADS)

Peysson, Yves; Imbeaux, Frédéric

1999-10-01

A new tomography dedicated to detailed studies of the fast electron bremsstrahlung emission in the hard x-ray (HXR) energy range between 20 and 200 keV during lower hybrid (LH) current drive experiments on the TORE SUPRA tokamak [Equipe TORE SUPRA, in Proceedings of the 15th Conference on Plasma Physics and Controlled Nuclear Fusion Research, Seville (International Atomic Energy Agency, Vienna, 1995), Vol. 1, AIEA-CN-60 / A1-5, p. 105] is presented. Radiation detection is performed by cadmium telluride semiconductors, which have most of the desirable features for a powerful diagnosing of magnetically confined hot plasmas—compact size, high x-ray stopping efficiency, fast timing characteristics, good energy resolution, no sensitivity to magnetic field, reasonable susceptibility to performance degradation from neutron/γ-induced damages. This instrument is made of two independent cameras viewing a poloidal cross-section of the plasma, with respectively 21 and 38 detectors. A coarse spectrometry—8 energy channels—is carried out for each chord, with an energy resolution of 20 keV. The spatial resolution in the core of the plasma is 4-5 cm, while the time sampling may be lowered down to of 2-4 ms. Powerful inversion techniques based on maximum entropy or regularization algorithms take full advantage of the large number of line-integrated measurements for very robust estimates of the local HXR profiles as a function of time and photon energy. A detailed account of main characteristics and performances of the diagnostic is reported, as well as preliminary results on LH current drive experiments.

Ultrasonic Stir Welding Development for Ground-Based and In Situ Fabrication and Repair for In-Space Propulsion Systems/Commercial Space Sector

NASA Technical Reports Server (NTRS)

Ding, Jeff

2015-01-01

The completed Center Innovation Fund (CIF) project used the upgraded Ultrasonic Stir Weld (USW) Prototype System (built in 2013/2014) to begin characterizing the weld process using 2219 aluminum (fig. 1). This work is being done in Bldg. 4755 at NASA Marshall Space Flight Center (MSFC). The capabilities of the USW system provides the means to precisely control and document individual welding parameters. The current upgraded system has the following capabilities: (1) Ability to 'pulse' ultrasonic (US) energy on and off and adjust parameters real-time (travel speed, spindle rpm, US amplitude, X and Z axis positions, and plunge and pin axis force; (2) Means to measure draw force; (3) Ability to record US power versus time; (4) Increasing stiffness of Z axis drive and reduce head deflection using laser technology; (5) Adding linear encoder to better control tool penetration setting; (6) Ultrasonic energy integrated into stir rod and containment plate; (7) Maximum 600 rpm; (8) Maximum Z force 15,000 lb; (9) Real-time data acquisition and logging capabilities at a minimum frequency of 10 Hz; and (10) Two separate transducer power supplies operating at 4.5 kW power.

Luminescence from cavitation bubbles deformed in uniform pressure gradients

NASA Astrophysics Data System (ADS)

Supponen, Outi; Obreschkow, Danail; Kobel, Philippe; Farhat, Mohamed

2017-09-01

Presented here are observations that demonstrate how the deformation of millimetric cavitation bubbles by a uniform pressure gradient quenches single-collapse luminescence. Our innovative measurement system captures a broad luminescence spectrum (wavelength range, 300-900 nm) from the individual collapses of laser-induced bubbles in water. By varying the bubble size, driving pressure, and perceived gravity level aboard parabolic flights, we probed the limit from aspherical to highly spherical bubble collapses. Luminescence was detected for bubbles of maximum radii within the previously uncovered range, R0=1.5 -6 mm, for laser-induced bubbles. The relative luminescence energy was found to rapidly decrease as a function of the bubble asymmetry quantified by the anisotropy parameter ζ , which is the dimensionless equivalent of the Kelvin impulse. As established previously, ζ also dictates the characteristic parameters of bubble-driven microjets. The threshold of ζ beyond which no luminescence is observed in our experiment closely coincides with the threshold where the microjets visibly pierce the bubble and drive a vapor jet during the rebound. The individual fitted blackbody temperatures range between Tlum=7000 and Tlum=11 500 K but do not show any clear trend as a function of ζ . Time-resolved measurements using a high-speed photodetector disclose multiple luminescence events at each bubble collapse. The averaged full width at half-maximum of the pulse is found to scale with R0 and to range between 10 and 20 ns.

Power and thermal characterization of a lithium-ion battery pack for hybrid-electric vehicles

NASA Astrophysics Data System (ADS)

Smith, Kandler; Wang, Chao-Yang

A 1D electrochemical, lumped thermal model is used to explore pulse power limitations and thermal behavior of a 6 Ah, 72 cell, 276 V nominal Li-ion hybrid-electric vehicle (HEV) battery pack. Depleted/saturated active material Li surface concentrations in the negative/positive electrodes consistently cause end of high-rate (∼25 C) pulse discharge at the 2.7 V cell -1 minimum limit, indicating solid-state diffusion is the limiting mechanism. The 3.9 V cell -1 maximum limit, meant to protect the negative electrode from lithium deposition side reaction during charge, is overly conservative for high-rate (∼15 C) pulse charges initiated from states-of-charge (SOCs) less than 100%. Two-second maximum pulse charge rate from the 50% SOC initial condition can be increased by as much as 50% without risk of lithium deposition. Controlled to minimum/maximum voltage limits, the pack meets partnership for next generation vehicles (PNGV) power assist mode pulse power goals (at operating temperatures >16 °C), but falls short of the available energy goal. In a vehicle simulation, the pack generates heat at a 320 W rate on a US06 driving cycle at 25 °C, with more heat generated at lower temperatures. Less aggressive FUDS and HWFET cycles generate 6-12 times less heat. Contact resistance ohmic heating dominates all other mechanisms, followed by electrolyte phase ohmic heating. Reaction and electronic phase ohmic heats are negligible. A convective heat transfer coefficient of h = 10.1 W m -2 K -1 maintains cell temperature at or below the 52 °C PNGV operating limit under aggressive US06 driving.

Predicting drowsy driving in real-time situations: Using an advanced driving simulator, accelerated failure time model, and virtual location-based services.

PubMed

Wang, Junhua; Sun, Shuaiyi; Fang, Shouen; Fu, Ting; Stipancic, Joshua

2017-02-01

This paper aims to both identify the factors affecting driver drowsiness and to develop a real-time drowsy driving probability model based on virtual Location-Based Services (LBS) data obtained using a driving simulator. A driving simulation experiment was designed and conducted using 32 participant drivers. Collected data included the continuous driving time before detection of drowsiness and virtual LBS data related to temperature, time of day, lane width, average travel speed, driving time in heavy traffic, and driving time on different roadway types. Demographic information, such as nap habit, age, gender, and driving experience was also collected through questionnaires distributed to the participants. An Accelerated Failure Time (AFT) model was developed to estimate the driving time before detection of drowsiness. The results of the AFT model showed driving time before drowsiness was longer during the day than at night, and was longer at lower temperatures. Additionally, drivers who identified as having a nap habit were more vulnerable to drowsiness. Generally, higher average travel speeds were correlated to a higher risk of drowsy driving, as were longer periods of low-speed driving in traffic jam conditions. Considering different road types, drivers felt drowsy more quickly on freeways compared to other facilities. The proposed model provides a better understanding of how driver drowsiness is influenced by different environmental and demographic factors. The model can be used to provide real-time data for the LBS-based drowsy driving warning system, improving past methods based only on a fixed driving. Copyright © 2016 Elsevier Ltd. All rights reserved.

Traction Drives for Zero Stick-Slip Robots, and Reaction Free, Momentum Balanced Systems

NASA Technical Reports Server (NTRS)

Anderson, William J.; Shipitalo, William; Newman, Wyatt

1995-01-01

Two differential (dual input, single output) drives (a roller-gear and a pure roller), and a momentum balanced (single input, dual output) drive (pure roller ) were designed, fabricated, and tested. The differential drives are each rated at 295 rad/sec (2800 rpm) input speed, 450 N-m (4,000 in-lbf) output torque. The momentum balanced drive is rated at 302 rad/sec (2880 rpm) input speed, and dual output torques of 434N-m (3840 in-lbf). The Dual Input Differential Roller-Gear Drive (DC-700) has a planetary roller-gear system with a reduction ratio (one input driving the output with the second input fixed) of 29.23: 1. The Dual Input Differential Roller Drive (DC-500) has a planetary roller system with a reduction ratio of approximately 24:1. Each of the differential drives features dual roller-gear or roller arrangements consisting of a sun, four first row planets, four second row planets, and a ring. The Momentum Balanced (Grounded Ring) Drive (DC-400) has a planetary roller system with a reduction ratio of 24:1 with both outputs counterrotating at equal speed. Its single roller cluster consists of a sun, five first and five second row planets, a roller cage or spider and a ring. Outputs are taken from both the roller cage and the ring which counterrotate. Test results reported for all three drives include angular and torque ripple (linearity and cogging), viscous and Coulomb friction, and forward and reverse power efficiency. Of the two differential drives, the Differential Roller Drive had better linearity and less cogging than did the Differential Roller-Gear Drive, but it had higher friction and lower efficiency (particularly at low power throughput levels). Use of full preloading rather than a variable preload system in the Differential Roller Drive assessed a heavy penalty in part load efficiency. Maximum measured efficiency (ratio of power out to power in) was 95% for the Differential Roller-Gear Drive and 86% for the Differential Roller Drive. The Momentum Balanced (Grounded Ring) Drive performed as expected kinematically. Reduction r-atios to the two counterrotating outputs (design nominal=24:1) were measured to be 23.98:1 and 24.12:1 at zero load.. At 25ONm (2200 in-lbf) output torque the ratio changed 2% due to roller creep. This drive was the smoothest of all three as determined from linearity and cogging tests, and maximum measured efficiency (ratio of power out to power in) was 95%. The disadvantages of full preloading as comvared to variable preload were apparent in this drive as in the Differential Roller Drive. Efficiencies at part load were low, but improved dramatically with increases in torque. These were consistent with friction measurements which indicated losses primarily from Coulomb friction. The initial preload level setting was low so roller slip was encountered at higher torques during testing.

H∞ controller design for a 4-meter direct-drive azimuth axis

NASA Astrophysics Data System (ADS)

Chen, Li-Yan; Zhang, Zhen-Chao; Song, Xiao-Li; Wang, Da-Xing

2015-11-01

To pursue a higher imaging resolution for exploring more details in the information conveyed by the Universe, the next generation of optical telescopes based on a direct drive widely employ the extremely large aperture structure, which also introduces more disturbances and uncertain factors to the control system. Facing this new challenge, the PID control method in main-axis control systems of traditional astronomical telescopes cannot suffice for the requirement of the tracking precision and disturbance sensitivity in angular velocity. To overcome this shortcoming, we establish a dynamic model and propose an H∞ controller for a 4-meter azimuth direct drive control system that consists of a revolving platform (azimuth axis), a three-phase torque motor, a motor drive, an encoder, a data acquisition card and a small computers. Simulations are carried out to analyze the model and guide the real experiments. Experimental results show that the proposed H∞ controller reduces the tracking error by a maximum of 80.69% (average 57.8%) and the disturbance sensitivity by a maximum of 82.3% (average 50.96%) compared with the traditional tuned PI controller; furthermore, the order of the model describing the proposed controller can be reduced to three, thus its feasibility in real systems is guaranteed.

Influence of different shoulder-elbow configurations on steering precision and steering velocity in automotive context.

PubMed

Schmidt, Susanne; Seiberl, Wolfgang; Schwirtz, Ansgar

2015-01-01

Ergonomic design requirements are needed to develop optimum vehicle interfaces for the driver. The majority of the current specifications consider only anthropometric conditions and subjective evaluations of comfort. This paper examines specific biomechanical aspects to improve the current ergonomic requirements. Therefore, a research which involved 40 subjects was carried out to obtain more knowledge in the field of steering movement while driving a car. Five different shoulder-elbow joint configurations were analyzed using a driving simulator to find optimum posture for driving in respect of steering precision and steering velocity. Therefore, a 20 s precision test and a test to assess maximum steering velocity over a range of 90° steering motion have been conducted. The results show that driving precision, as well as maximum steering velocity, are significantly increased in mid-positions (elbow angles of 95° and 120°) compared to more flexed (70°) or extended (145° and 160°) postures. We conclude that driver safety can be enhanced by implementing these data in the automotive design process because faster and highly precise steering can be important during evasive actions and in accident situations. In addition, subjective comfort rating, analyzed with questionnaires, confirmed experimental results. Copyright © 2014 Elsevier Ltd and The Ergonomics Society. All rights reserved.

A ring-type multi-DOF ultrasonic motor with four feet driving consistently.

PubMed

Shi, Shengjun; Xiong, Huaiyin; Liu, Yingxiang; Chen, Weishan; Liu, Junkao

2017-04-01

A new type of multiple-degree-of-freedom (multi-DOF) ultrasonic motor was developed aiming at high output torque and compact structure. To reach this purpose, a ring type composite stator was proposed with four driving feet uniformly arranged in the inner circumference of the ring stator. The stator employs two orthogonal axial bending modes and a radial bending mode, by exciting two of them simultaneously, to generate elliptic trajectories on driving feet tips and to push sphere rotor around x, y and z axis respectively. Based on the deduced criteria, a specific combination of the A(0,5) axial bending modes and R(0,2) radial bending mode were chosen to realize that the rotating directions of the elliptical driving trajectories on four feet tips can push the sphere rotor to spin in the same direction consistently, thus the efficiency and output performance will be improved by decreasing the slip between feet and rotor. FEM was used to design the motor including selecting key parameters to tune the resonant frequencies by sensitivity analysis, and a prototype was fabricated and tested. The experiment results showed that the maximum output torque of the motor is 0.118Nm and the maximum speed is 55r/min. Copyright © 2017 Elsevier B.V. All rights reserved.

The impact of continuous driving time and rest time on commercial drivers' driving performance and recovery.

PubMed

Wang, Lianzhen; Pei, Yulong

2014-09-01

This real road driving study was conducted to investigate the effects of driving time and rest time on the driving performance and recovery of commercial coach drivers. Thirty-three commercial coach drivers participated in the study, and were divided into three groups according to driving time: (a) 2 h, (b) 3 h, and (c) 4 h. The Stanford Sleepiness Scale (SSS) was used to assess the subjective fatigue level of the drivers. One-way ANOVA was employed to analyze the variation in driving performance. The statistical analysis revealed that driving time had a significant effect on the subjective fatigue and driving performance measures among the three groups. After 2 h of driving, both the subjective fatigue and driving performance measures began to deteriorate. After 4 h of driving, all of the driving performance indicators changed significantly except for depth perception. A certain amount of rest time eliminated the negative effects of fatigue. A 15-minute rest allowed drivers to recover from a two-hour driving task. This needed to be prolonged to 30 min for driving tasks of 3 to 4 h of continuous driving. Drivers' attention, reactions, operating ability, and perceptions are all affected in turn after over 2 h of continuous driving. Drivers should take a certain amount of rest to recover from the fatigue effects before they continue driving. Copyright © 2014 National Safety Council and Elsevier Ltd. All rights reserved.

Heating of the solar middle chromosphere by large-scale electric currents

NASA Technical Reports Server (NTRS)

Goodman, M. L.

1995-01-01

A global resistive, two-dimensional, time-dependent magnetohydrodynamic (MHD) model is used to introduce and support the hypothesis that the quiet solar middle chromosphere is heated by resistive dissipation of large-scale electric currents which fill most of its volume. The scale height and maximum magnitude of the current density are 400 km and 31.3 m/sq m, respectively. The associated magnetic field is almost horizontal, has the same scale height as the current density, and has a maximum magnitude of 153 G. The current is carried by electrons flowing across magnetic field lines at 1 m/s. The resistivity is the electron contribution to the Pedersen resitivity for a weakly ionized, strongly magnetized, hydrogen gas. The model does not include a driving mechanism. Most of the physical quantities in the model decrease exponentially with time on a resistive timescale of 41.3 minutes. However, the initial values and spatial; dependence of these quantities are expected to be essentially the same as they would be if the correct driving mechanism were included in a more general model. The heating rate per unit mass is found to be 4.5 x 10(exp 9) ergs/g/s, independent of height and latitude. The electron density scale height is found to be 800 km. The model predicts that 90% of the thermal energy required to heat the middle chromosphere is deposited in the height range 300-760 km above the temperature minimum. It is shown to be consistent to assume that the radiation rate per unit volume is proportional to the magnetic energy density, and then it follows that the heating rate per unit volume is also proportional to the energy from the photosphere into the overlying chromosphere are briefly discussed as possible driving mechanisms for establishing and maintaining the current system. The case in which part of or all of the current is carried by protons and metal ions, and the contribution of electron-proton scattering to the current are also considered, with the conclusion that these effects do not change the qualitative prediction of the model, but probably change the quantitative predictions slightly, mainly by increasing the maximum magntiude of the current density and magnetic field to at most approximately 100 mA/m and approximately 484 G, respectively. The heating rate per unit mass, current density scale height, magnetic field scale height, temperatures, and pressures are unchanged or are only slightly changed by including these additional effects due to protons and ions.

Effect of black point on accuracy of LCD displays colorimetric characterization

NASA Astrophysics Data System (ADS)

Li, Tong; Xie, Kai; He, Nannan; Ye, Yushan

2018-03-01

Black point is the point at which RGB's single channel digital drive value is 0. Due to the problem of light leakage of liquid-crystal displays (LCDs), black point's luminance value is not 0, this phenomenon bring some errors to colorimetric characterization of LCDs, especially low luminance value driving greater sampling effect. This paper describes the characteristic accuracy of polynomial model method and the effect of black point on accuracy, the color difference accuracy is given. When considering the black point in the characteristics equation, the maximum color difference is 3.246, the maximum color difference than without considering the black points reduced by 2.36. The experimental results show that the accuracy of LCDs colorimetric characterization can be improved, if the effect of black point is eliminated properly.

Fuzzy Logic Controlled Solar Module for Driving Three- Phase Induction Motor

NASA Astrophysics Data System (ADS)

Afiqah Zainal, Nurul; Sooi Tat, Chan; Ajisman

2016-02-01

Renewable energy produced by solar module gives advantages for generated three- phase induction motor in remote area. But, solar module's ou tput is uncertain and complex. Fuzzy logic controller is one of controllers that can handle non-linear system and maximum power of solar module. Fuzzy logic controller used for Maximum Power Point Tracking (MPPT) technique to control Pulse-Width Modulation (PWM) for switching power electronics circuit. DC-DC boost converter used to boost up photovoltaic voltage to desired output and supply voltage source inverter which controlled by three-phase PWM generated by microcontroller. IGBT switched Voltage source inverter (VSI) produced alternating current (AC) voltage from direct current (DC) source to control speed of three-phase induction motor from boost converter output. Results showed that, the output power of solar module is optimized and controlled by using fuzzy logic controller. Besides that, the three-phase induction motor can be drive and control using VSI switching by the PWM signal generated by the fuzzy logic controller. This concluded that the non-linear system can be controlled and used in driving three-phase induction motor.

Design and testing of a novel piezoelectric micro-motor actuated by asymmetrical inertial impact driving principle.

PubMed

Zeng, Ping; Sun, Shujie; Li, Li'an; Xu, Feng; Cheng, Guangming

2014-03-01

In this paper, an asymmetrical inertial impact driving principle is first proposed, and accordingly a novel piezoelectrically actuated linear micro-motor is developed. It is driven by the inertial impact force generated by piezoelectric smart cantilever (PSC) with asymmetrical clamping locations during a driving cycle. When the PSC is excited by typical harmonic voltage signals, different equivalent stiffness will be induced due to its asymmetrical clamping locations when it is vibrating back and forth, leading to a tiny displacement difference on the two opposite directions in a cycle, and then the accumulation of tiny displacement difference will allow directional movements. A prototype of the proposed motor has been developed and investigated by means of experimental tests. The motion and dynamics characteristics of the prototype are well studied. The experimental results demonstrate that the resolution of the micro-motor is 0.02 μm, the maximum velocity is 16.87 mm/s, and the maximum loading capacity can reach up to 1 kg with a voltage of 100 V and 35 Hz.

Solar maximum mission/ultraviolet spectrometer and polarimeter studies

NASA Technical Reports Server (NTRS)

Henze, William, Jr.

1993-01-01

This final report for NASA Contract No. NAS8-35921 describes various studies performed for the Ultraviolet Spectrometer and Polarimeter (UVSP) experiment, one of several instruments on the Solar Maximum Mission (SMM) satellite which was launched on 14 February 1980. The UVSP consisted primarily of a Gregorian telescope and an Ebert-Fastie spectrometer with a polarimeter that could be inserted into the light path. The spacecraft and most of the instruments, including the UVSP, operated successfully until 23 November 1980, when part of the SMM attitude control system (fine pointing control) failed. The UVSP was then unable to observe the Sun until 18 April 1984, when the SMM was visited by the space shuttle and the attitude control module was replaced by astronauts. The SMM mission ended when the spacecraft reentered the atmosphere of the Earth and was thereby destroyed on 2 December 1989. The topics covered in this report include the following: (1) ultraviolet stellar polarimetry (probably the first such attempted measurement); no polarization as detected and the upper limits, based on the sensitivity as determined by the observed count rate, are rather high; (2) an investigation into the possible position of the UVSP wavelength drive after it became stuck on 26 April 1985; (3) fast timing tests for sit-and-state observations involving one or two detectors; (4) development of computer subroutines to allow the calculation of the component of the SMM spacecraft orbital velocity along the line of sight to the Sun at any desired time during the 1984/1985 period when the UVSP wavelength drive was operating properly; (5) listing of published research papers; (6) description of the UVSP catalog of observations; and (7) description of UVSP calibration report and data users guide.

Hardware system of X-wave generator with simple driving pulses

NASA Astrophysics Data System (ADS)

Li, Xu; Li, Yaqin; Xiao, Feng; Ding, Mingyue; Yuchi, Ming

2013-03-01

The limited diffraction beams such as X-wave have the properties of larger depth of field. Thus, it has the potential to generate ultra-high frame rate ultrasound images. However, in practice, the real-time generation of X-wave ultrasonic field requires complex and high-cost system, especially the precise and specific voltage time distribution part for the excitation of each distinct array element. In order to simplify the hardware realization of X-wave, based on the previous works, X-wave excitation signals were decomposed and expressed as the superposition of a group of simple driving pulses, such as rectangular and triangular waves. The hardware system for the X-wave generator was also designed. The generator consists of a computer for communication with the circuit, universal serial bus (USB) based micro-controller unit (MCU) for data transmission, field programmable gate array (FPGA) based Direct Digital Synthesizer(DDS), 12-bit digital-to-analog (D/A) converter and a two stage amplifier.The hardware simulation results show that the designed system can generate the waveforms at different radius approximating the theoretical X-wave excitations with a maximum error of 0.49% triggered by the quantification of amplitude data.

The MIS 3 maximum of the Torres del Paine and Última Esperanza ice lobes in Patagonia and the pacing of southern mountain glaciation

NASA Astrophysics Data System (ADS)

García, Juan-Luis; Hein, Andrew S.; Binnie, Steven A.; Gómez, Gabriel A.; González, Mauricio A.; Dunai, Tibor J.

2018-04-01

The timing, structure and termination of the last southern mountain glaciation and its forcing remains unclear. Most studies have focused on the global Last Glacial Maximum (LGM; 26.5-19 ka) time period, which is just part of the extensive time-frame within the last glacial period, including Marine Isotope Stages 3 and 4. Understanding the glacial fluctuations throughout the glacial period is a prerequisite for uncovering the cause and climate mechanism driving southern glaciation and the interhemispheric linkages of climate change. Here, we present an extensive (n = 65) cosmogenic 10Be glacier chronology derived from moraine belts marking the pre-global LGM extent of the former Patagonian Ice Sheet in southernmost South America. Our results show the mountain ice sheet reached its maximum extent at 48.0 ± 1.8 ka during the local LGM, but attained just half this extent at 21.5 ± 1.8 ka during the global LGM. This finding, supported by nearby glacier chronologies, indicates that at orbital time scales, the southern mid-latitude glaciers fluctuated out-of-phase with northern hemisphere ice sheets. At millennial time-scales, our data suggest that Patagonian and New Zealand glaciers advanced in unison with cold Antarctic stadials and reductions in Southern Ocean sea surface temperatures. This implies a southern middle latitudes-wide millennial rhythm of climate change throughout the last glacial period linked to the north Atlantic by the bipolar seesaw. We suggest that winter insolation, acting alongside other drivers such as the strength and/or position of the southern westerlies, controlled the extents of major southern mountain glaciers such as those in southernmost South America.

High-energy electron emission from metallic nano-tips driven by intense single-cycle terahertz pulses

PubMed Central

Li, Sha; Jones, R. R.

2016-01-01

Electrons ejected from atoms and subsequently driven to high energies in strong laser fields enable techniques from attosecond pulse generation to imaging with rescattered electrons. Analogous processes govern strong-field electron emission from nanostructures, where long wavelength radiation and large local field enhancements hold the promise for producing electrons with substantially higher energies, allowing for higher resolution time-resolved imaging. Here we report on the use of single-cycle terahertz pulses to drive electron emission from unbiased nano-tips. Energies exceeding 5 keV are observed, substantially greater than previously attained at higher drive frequencies. Despite large differences in the magnitude of the respective local fields, we find that the maximum electron energies are only weakly dependent on the tip radius, for 10 nm

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phillips, Benjamin R.; Baldridge, W. Scott; Gable, Carl W.

Finite volume calculations of the flow of rhyolite are presented to investigate the fate of viscous magmas flowing in planar fractures with realistic length to width ratios of up to 2500:1. Heat and mass transfer for a melt with a temperature dependent viscosity and the potential to undergo phase change are considered. Magma driving pressures and dike widths are chosen to satisfy simple elastic considerations. These models are applied within a parameter space relevant to the Banco Bonito rhyolite flow, Valles caldera, New Mexico. We estimate a maximum eruption duration for the event of ~200 days, realized at a minimummore » possible dike width of 5-6 m and driving pressure of 7-8 MPa. Simplifications in the current model may warrant scaling of these results. However, we demonstrate the applicability of our model to magma dynamics issues and suggest that such models may be used to infer information about both the timing of an eruption and the evolution of the associated magma source.« less

Combinational logic for generating gate drive signals for phase control rectifiers

NASA Technical Reports Server (NTRS)

Dolland, C. R.; Trimble, D. W. (Inventor)

1982-01-01

Control signals for phase-delay rectifiers, which require a variable firing angle that ranges from 0 deg to 180 deg, are derived from line-to-line 3-phase signals and both positive and negative firing angle control signals which are generated by comparing current command and actual current. Line-to-line phases are transformed into line-to-neutral phases and integrated to produce 90 deg phase delayed signals that are inverted to produce three cosine signals, such that for each its maximum occurs at the intersection of positive half cycles of the other two phases which are inputs to other inverters. At the same time, both positive and negative (inverted) phase sync signals are generated for each phase by comparing each with the next and producing a square wave when it is greater. Ramp, sync and firing angle controls signals are than used in combinational logic to generate the gate firing control signals SCR gate drives which fire SCR devices in a bridge circuit.

Brain Mechanisms for Making, Breaking, and Changing Rules

NASA Astrophysics Data System (ADS)

Levine, Daniel S.

Individuals differ widely, and the same person varies over time, in their tendency to seek maximum information versus their tendency to follow the simplest heuristics. Neuroimaging studies suggest which brain regions might mediate the balance between knowledge maximization and heuristic simplification. The amygdala is more activated in individuals who use primitive heuristics, whereas two areas of the frontal lobes are more activated in individuals with a strong knowledge drive: one area involved in detecting risk or conflict, and another involved in choosing task-appropriate responses. Both of these motivations have engineering uses. There is benefit to understanding a situation at a high enough level to respond in a flexible manner when the context is complex and time allows detailed consideration. Yet simplifying heuristics can yield benefits when the context is routine or when time is limited.

Directed translocation of a flexible polymer through a cone-shaped nano-channel

NASA Astrophysics Data System (ADS)

Nikoofard, Narges; Khalilian, Hamidreza; Fazli, Hossein

2013-08-01

Translocation of a flexible polymer through a cone-shaped channel is studied, theoretically and using computer simulations. Our simulations show that the shape of the channel causes the polymer translocation to be a driven process. The effective driving force of entropic origin acting on the polymer is calculated as a function of the length and the apex-angle of the channel, theoretically. It is found that the translocation time is a non-monotonic function of the apex-angle of the channel. By increasing the apex-angle from zero, the translocation time shows a minimum and then a maximum. Also, it is found that regardless of the value of the apex-angle, the translocation time is a uniformly decreasing function of the channel length. The results of the theory and the simulation are in good qualitative agreement.

A Four-Feet Walking-Type Rotary Piezoelectric Actuator with Minute Step Motion.

PubMed

Liu, Yingxiang; Wang, Yun; Liu, Junkao; Xu, Dongmei; Li, Kai; Shan, Xiaobiao; Deng, Jie

2018-05-08

A four-feet walking-type rotary piezoelectric actuator with minute step motion was proposed. The proposed actuator used the rectangular motions of four driving feet to push the rotor step-by-step; this operating principle was different with the previous non-resonant actuators using direct-driving, inertial-driving, and inchworm-type mechanisms. The mechanism of the proposed actuator was discussed in detail. Transient analyses were accomplished by ANSYS software to simulate the motion trajectory of the driving foot and to find the response characteristics. A prototype was manufactured to verify the mechanism and to test the mechanical characteristics. A minimum resolution of 0.095 μrad and a maximum torque of 49 N·mm were achieved by the prototype, and the output speed was varied by changing the driving voltage and working frequency. This work provides a new mechanism for the design of a rotary piezoelectric actuator with minute step motion.

A Four-Feet Walking-Type Rotary Piezoelectric Actuator with Minute Step Motion

PubMed Central

Wang, Yun; Liu, Junkao; Xu, Dongmei; Li, Kai; Shan, Xiaobiao; Deng, Jie

2018-01-01

A four-feet walking-type rotary piezoelectric actuator with minute step motion was proposed. The proposed actuator used the rectangular motions of four driving feet to push the rotor step-by-step; this operating principle was different with the previous non-resonant actuators using direct-driving, inertial-driving, and inchworm-type mechanisms. The mechanism of the proposed actuator was discussed in detail. Transient analyses were accomplished by ANSYS software to simulate the motion trajectory of the driving foot and to find the response characteristics. A prototype was manufactured to verify the mechanism and to test the mechanical characteristics. A minimum resolution of 0.095 μrad and a maximum torque of 49 N·mm were achieved by the prototype, and the output speed was varied by changing the driving voltage and working frequency. This work provides a new mechanism for the design of a rotary piezoelectric actuator with minute step motion. PMID:29738495

Evaluation of the Evidence Base for the Alcohol Industry’s Actions to Reduce Drink Driving Globally

PubMed Central

Esser, Marissa B.; Bao, James; Jernigan, David H.

2016-01-01

Objectives. To evaluate the evidence base for the content of initiatives that the alcohol industry implemented to reduce drink driving from 1982 to May 2015. Methods. We systematically analyzed the content of 266 global initiatives that the alcohol industry has categorized as actions to reduce drink driving. Results. Social aspects public relations organizations (i.e., organizations funded by the alcohol industry to handle issues that may be damaging to the business) sponsored the greatest proportion of the actions. Only 0.8% (n = 2) of the sampled industry actions were consistent with public health evidence of effectiveness for reducing drink driving. Conclusions. The vast majority of the alcohol industry’s actions to reduce drink driving does not reflect public health evidenced–based recommendations, even though effective drink-driving countermeasures exist, such as a maximum blood alcohol concentration limit of 0.05 grams per deciliter for drivers and widespread use of sobriety checkpoints. PMID:26890181

ICRF fast wave current drive and mode conversion current drive in EAST tokamak

NASA Astrophysics Data System (ADS)

Yin, L.; Yang, C.; Gong, X. Y.; Lu, X. Q.; Du, D.; Chen, Y.

2017-10-01

Fast wave in the ion-cyclotron resonance frequency (ICRF) range is a promising candidate for non-inductive current drive (CD), which is essential for long pulse and high performance operation of tokamaks. A numerical study on the ICRF fast wave current drive (FWCD) and mode-conversion current drive (MCCD) in the Experimental Advanced Superconducting Tokamak (EAST) is carried out by means of the coupled full wave and Ehst-Karney parameterization methods. The results show that FWCD efficiency is notable in two frequency regimes, i.e., f ≥ 85 MHz and f = 50-65 MHz, where ion cyclotron absorption is effectively avoided, and the maximum on-axis driven current per unit power can reach 120 kA/MW. The sensitivity of the CD efficiency to the minority ion concentration is confirmed, owing to fast wave mode conversion, and the peak MCCD efficiency is reached for 22% minority-ion concentration. The effects of the wave-launch position and the toroidal wavenumber on the efficiency of current drive are also investigated.

Plasmonic nanoparticle chain in a light field: a resonant optical sail.

PubMed

Albaladejo, Silvia; Sáenz, Juan José; Marqués, Manuel I

2011-11-09

Optical trapping and driving of small objects has become a topic of increasing interest in multidisciplinary sciences. We propose to use a chain made of metallic nanoparticles as a resonant light sail, attached by one end point to a transparent object and propelling it by the use of electromagnetic radiation. Driving forces exerted on the chain are theoretically studied as a function of radiation's wavelength and chain's alignments with respect to the direction of radiation. Interestingly, there is a window in the frequency spectrum in which null-torque equilibrium configuration, with minimum geometric cross section, corresponds to a maximum in the driving force.

EFFECTS OF DIFFERENT WARM-UP PROGRAMS ON GOLF PERFORMANCE IN ELITE MALE GOLFERS

PubMed Central

Macfarlane, Alison

2012-01-01

Background: The physical demands required of the body to execute a shot in golf are enormous. Current evidence suggests that warm-up involving static stretching is detrimental to immediate performance in golf as opposed to active dynamic stretching. However the effect of resistance exercises during warm-up before golf on immediate performance is unknown. Therefore, the purpose of this study was to assess the effects of three different warm-up programs on immediate golf performance. Methods: Fifteen elite male golfers completed three different warm-up programs over three sessions on non-consecutive days. After each warm-up program each participant hit ten maximal drives with the ball flight and swing analyzed with Flightscope® to record maximum club head speed (MCHS), maximal driving distance (MDD), driving accuracy (DA), smash factor (SF) and consistent ball strike (CBS). Results: Repeated measures ANOVA tests showed statistically significant difference within 3 of the 5 factors of performance (MDD, CBS and SF). Subsequently, a paired t-test then showed statistically significant (p<0.05) improvements occurred in each of these three factors in the group performing a combined active dynamic and functional resistance (FR) warm-up as opposed to either the active dynamic (AD) warm-up or the combined AD with weights warm-up (WT). There were no statistically significant differences observed between the AD warm-up and the WT warm-up for any of the five performance factors and no statistical significant difference between any of the warm-ups for maximum clubhead speed (MCHS) and driving accuracy (DA). Conclusion: Performing a combined AD and FR warm up with Theraband® leads to significant increase in immediate performance of certain factors of the golf drive compared to performing an AD warm-up by itself or a combined AD with WT warm-up. No significant difference was observed between the three warm-up groups when looking at immediate effect on driving accuracy or maximum club head speed. The addition of functional resistance activities to active dynamic stretching has immediate benefits to elite male golfers in relation to some factors of their performance. Level of Evidence: This study is a Quantitative Experimental design using repeated measures and multiple crossovers. It cannot be classified using the descriptive level of evidence. PMID:23936749

Social and Behavioral Characteristics of Young Adult Drink/Drivers Adjusted for Level of Alcohol Use

PubMed Central

Bingham, C. Raymond; Elliott, Michael R.; Shope, Jean T.

2007-01-01

Background Alcohol consumption and drink/driving are positively correlated and many predictors of alcohol use also predict drink/driving. Past research has not fully distinguished the contributions of personal risk factors from the level of alcohol use in the prediction of drink/driving. As a result, the extent to which predictors are specific to drink/driving, versus due to a mutual association to alcohol use, is unclear. Methods This study examined the unique and shared risk factors for drink/driving and alcohol use, and examined the attributable risk (AR) associated with predictors of drink/driving while adjusting for alcohol use. Study data were from a telephone survey of 3,480 Michigan-licensed young adults who were drinkers. Four groups of drink/drivers were formed based on the prior 12-month maximum severity of drink/driving: (1) never drink/driving; (2) driving at least once within an hour of 1 or 2 drinks; (3) driving within an hour of 3 or more drinks or while feeling the effects of alcohol; and (4) drinking while driving. Results Lower perceived risk of drink/driving, greater social support for drinking and drink/driving, greater aggression and delinquency, more cigarette smoking, and more risky driving behaviors uniquely predicted drink/driving severity in models adjusted for alcohol use. The largest ARs were associated with social support for drinking and drink/driving and perceived risk of drink/driving. Conclusions These results confirm that alcohol use and drink/driving share risk factors, but also indicate that part of the variation in these factors is specific to drink/driving. Implications for interventions to reduce drink/driving are discussed. PMID:17374045

Investigation of hit-and-run crash occurrence and severity using real-time loop detector data and hierarchical Bayesian binary logit model with random effects.

PubMed

Xie, Meiquan; Cheng, Wen; Gill, Gurdiljot Singh; Zhou, Jiao; Jia, Xudong; Choi, Simon

2018-02-17

Most of the extensive research dedicated to identifying the influential factors of hit-and-run (HR) crashes has utilized typical maximum likelihood estimation binary logit models, and none have employed real-time traffic data. To fill this gap, this study focused on investigating factors contributing to HR crashes, as well as the severity levels of HR. This study analyzed 4-year crash and real-time loop detector data by employing hierarchical Bayesian models with random effects within a sequential logit structure. In addition to evaluation of the impact of random effects on model fitness and complexity, the prediction capability of the models was examined. Stepwise incremental sensitivity and specificity were calculated and receiver operating characteristic (ROC) curves were utilized to graphically illustrate the predictive performance of the model. Among the real-time flow variables, the average occupancy and speed from the upstream detector were observed to be positively correlated with HR crash possibility. The average upstream speed and speed difference between upstream and downstream speeds were correlated with the occurrence of severe HR crashes. In addition to real-time factors, other variables found influential for HR and severe HR crashes were length of segment, adverse weather conditions, dark lighting conditions with malfunctioning street lights, driving under the influence of alcohol, width of inner shoulder, and nighttime. This study suggests the potential traffic conditions of HR and severe HR occurrence, which refer to relatively congested upstream traffic conditions with high upstream speed and significant speed deviations on long segments. The above findings suggest that traffic enforcement should be directed toward mitigating risky driving under the aforementioned traffic conditions. Moreover, enforcement agencies may employ alcohol checkpoints to counter driving under the influence (DUI) at night. With regard to engineering improvements, wider inner shoulders may be constructed to potentially reduce HR cases and street lights should be installed and maintained in working condition to make roads less prone to such crashes.

Topographic aspects of photic driving in the electroencephalogram of children and adolescents.

PubMed

Lazarev, V V; Infantosi, A F C; Valencio-de-Campos, D; deAzevedo, L C

2004-06-01

The electroencephalogram amplitude spectra at 11 fixed frequencies of intermittent photic stimulation of 3 to 24 Hz were combined into driving "profiles" for 14 scalp points in 8 male and 7 female normal subjects aged 9 to 17 years. The driving response varied over frequency and was detected in 70 to 100% of cases in the occipital areas (maximum) and in 27 to 77% of cases in the frontal areas (minimum) using as a criterion peak amplitude 20% higher than those of the neighbors. Each subject responded, on average, to 9.7 +/- 1.15 intermittent photic stimulation frequencies in the right occipital area and to 6.8 +/- 1.97 frequencies in the right frontal area. Most of the driving responses (in relation to the previous background) were significant according to the spectral F-test (alpha = 0.05), which also detected changes in some cases of low amplitude responses not revealed by the peak criterion. The profiles had two maxima in the alpha and theta bands in all leads. The latter was not present in the background spectra in the posterior areas and was less pronounced in the anterior ones. The weight of the profile theta maximum increased towards the frontal areas where the two maxima were similar, while the profile amplitudes decreased. The profiles repeated the shape of the background spectra, except for the theta band. The interhemispheric correlation between profiles was high. The theta driving detected in all areas recorded suggests a generalized influence of the theta generators in prepubertal and pubertal subjects.

Small passenger car transmission test: Dodge Omni A-404 transmission

NASA Technical Reports Server (NTRS)

Bujold, M. P.

1980-01-01

The small passenger car transmission test was initiated to supply electric vehicle manufacturers with technical information regarding the performance of commercially available transmissions. This transmission was tested in accordance with a passenger car automatic transmission test code (SAE J65lb) which required drive performance, coast performance, and no load test conditions. Under these test conditions, the transmission attained maximum efficiencies in the mid eighty percent range for both drive performance test and coast performance tests.

Increasing shot and data collection rates of the Shock/Shear experiment at the National Ignition Facility

DOE PAGES

Doss, F. W.; Flippo, K. A.; Capelli, D.; ...

2016-05-26

Updates to the Los Alamos laser-driven high-energy-density Shock/Shear mixing- layer experiment are reported, which have collectively increased the platform's shot and data acquisition rates. Also, the strategies employed have included a move from two-strip to four-strip imagers (allowing four times to be recorded per shot instead of two), the implementation of physics-informed rules of engagements allowing for the maximum flexibility in a shot's total energy and symmetry performance, and by splitting the laser's main drive pulse from a monolithic single pulse equal to all beams into a triply-segmented pulse which minimizes optics damage.

Increasing shot and data collection rates of the Shock/Shear experiment at the National Ignition Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doss, F. W.; Flippo, K. A.; Capelli, D.

Updates to the Los Alamos laser-driven high-energy-density Shock/Shear mixing- layer experiment are reported, which have collectively increased the platform's shot and data acquisition rates. Also, the strategies employed have included a move from two-strip to four-strip imagers (allowing four times to be recorded per shot instead of two), the implementation of physics-informed rules of engagements allowing for the maximum flexibility in a shot's total energy and symmetry performance, and by splitting the laser's main drive pulse from a monolithic single pulse equal to all beams into a triply-segmented pulse which minimizes optics damage.

An Arduino-Based Resonant Cradle Design with Infant Cries Recognition

PubMed Central

Chao, Chun-Tang; Wang, Chia-Wei; Chiou, Juing-Shian; Wang, Chi-Jo

2015-01-01

This paper proposes a resonant electric cradle design with infant cries recognition, employing an Arduino UNO as the core processor. For most commercially available electric cradles, the drive motor is closely combined with the bearing on the top, resulting in a lot of energy consumption. In this proposal, a ball bearing design was adopted and the driving force is under the cradle to increase the distance from the object to fulcrum and torque. The sensors are designed to detect the oscillation state, and then the force is driven at the critical time to achieve the maximum output response while saving energy according to the principle of resonance. As for the driving forces, the winding power and motors are carefully placed under the cradle. The sensors, including the three-axis accelerometer and infrared sensor, are tested and applied under swinging amplitude control. In addition, infant cry recognition technology was incorporated in the design to further develop its functionality, which is a rare feature in this kind of hardware. The proposed nonlinear operator of fundamental frequency (f0) analysis is able to identify different types of infant cries. In conclusion, this paper proposes an energy-saving electric cradle with infant cries recognition and the experimental results demonstrate the effectiveness of this approach. PMID:26247947

An Arduino-Based Resonant Cradle Design with Infant Cries Recognition.

PubMed

Chao, Chun-Tang; Wang, Chia-Wei; Chiou, Juing-Shian; Wang, Chi-Jo

2015-08-03

This paper proposes a resonant electric cradle design with infant cries recognition, employing an Arduino UNO as the core processor. For most commercially available electric cradles, the drive motor is closely combined with the bearing on the top, resulting in a lot of energy consumption. In this proposal, a ball bearing design was adopted and the driving force is under the cradle to increase the distance from the object to fulcrum and torque. The sensors are designed to detect the oscillation state, and then the force is driven at the critical time to achieve the maximum output response while saving energy according to the principle of resonance. As for the driving forces, the winding power and motors are carefully placed under the cradle. The sensors, including the three-axis accelerometer and infrared sensor, are tested and applied under swinging amplitude control. In addition, infant cry recognition technology was incorporated in the design to further develop its functionality, which is a rare feature in this kind of hardware. The proposed nonlinear operator of fundamental frequency (f0) analysis is able to identify different types of infant cries. In conclusion, this paper proposes an energy-saving electric cradle with infant cries recognition and the experimental results demonstrate the effectiveness of this approach.

Defining quality in radiology.

PubMed

Blackmore, C Craig

2007-04-01

The introduction of pay for performance in medicine represents an opportunity for radiologists to define quality in radiology. Radiology quality can be defined on the basis of the production model that currently drives reimbursement, codifying the role of radiologists as being limited to the production of timely and accurate radiology reports produced in conditions of maximum patient safety and communicated in a timely manner. Alternately, quality in radiology can also encompass the professional role of radiologists as diagnostic imaging specialists responsible for the appropriate use, selection, interpretation, and application of imaging. Although potentially challenging to implement, the professional model for radiology quality is a comprehensive assessment of the ways in which radiologists add value to patient care. This essay is a discussion of the definition of radiology quality and the implications of that definition.

Examing the Effects of Different IMF, F10.7, and Auroral Inputs on the Thermospheric Neutral Winds

NASA Astrophysics Data System (ADS)

Deng, Y.; Ridley, A. J.

2003-12-01

To obtain a better understanding of how the magnetosphere effects the global thermospheric and ionospheric structure, we conduct some numerical experiments using the University of Michigan's Global Ionosphere-Thermosphere Model (GITM). We have run GITM to roughly steady-state using different strengths of the high-latitude electric potential pattern, F10.7, and auroral inputs to determine how these effect the temporal history and stead-state of the thermospheric neutral winds. Our model reproduces the well known fact that the neutral winds are strongly driven by the ion convection above approximately 300 km, and that the ramp-up time is very dependent upon the altitude. We show quantitative results of the ramp-up times and maximum neutral wind speeds for the different driving conditions.

Automotive Stirling Engine Development Program Mod I Stirling engine development

NASA Technical Reports Server (NTRS)

Simetkosky, M. A.

1983-01-01

The development of the Mod I 4-cylinder automotive Stirling engine is discussed and illustrated with drawings, block diagrams, photographs, and graphs and tables of preliminary test data. The engine and its drive, cold-engine, hot-engine, external-heat, air/fuel, power-control, electronic-control, and auxiliary systems are characterized. Performance results from a total of 1900 h of tests on 4 prototype engines include average maximum efficiency (at 2000 rpm) 34.5 percent and maximum output power 54.4 kW. The modifications introduced in an upgraded version of the Mod I are explained; this engine has maximum efficiency 40.4 percent and maximum power output 69.2 kW.

TORBEAM 2.0, a paraxial beam tracing code for electron-cyclotron beams in fusion plasmas for extended physics applications

NASA Astrophysics Data System (ADS)

Poli, E.; Bock, A.; Lochbrunner, M.; Maj, O.; Reich, M.; Snicker, A.; Stegmeir, A.; Volpe, F.; Bertelli, N.; Bilato, R.; Conway, G. D.; Farina, D.; Felici, F.; Figini, L.; Fischer, R.; Galperti, C.; Happel, T.; Lin-Liu, Y. R.; Marushchenko, N. B.; Mszanowski, U.; Poli, F. M.; Stober, J.; Westerhof, E.; Zille, R.; Peeters, A. G.; Pereverzev, G. V.

2018-04-01

The paraxial WKB code TORBEAM (Poli, 2001) is widely used for the description of electron-cyclotron waves in fusion plasmas, retaining diffraction effects through the solution of a set of ordinary differential equations. With respect to its original form, the code has undergone significant transformations and extensions, in terms of both the physical model and the spectrum of applications. The code has been rewritten in Fortran 90 and transformed into a library, which can be called from within different (not necessarily Fortran-based) workflows. The models for both absorption and current drive have been extended, including e.g. fully-relativistic calculation of the absorption coefficient, momentum conservation in electron-electron collisions and the contribution of more than one harmonic to current drive. The code can be run also for reflectometry applications, with relativistic corrections for the electron mass. Formulas that provide the coupling between the reflected beam and the receiver have been developed. Accelerated versions of the code are available, with the reduced physics goal of inferring the location of maximum absorption (including or not the total driven current) for a given setting of the launcher mirrors. Optionally, plasma volumes within given flux surfaces and corresponding values of minimum and maximum magnetic field can be provided externally to speed up the calculation of full driven-current profiles. These can be employed in real-time control algorithms or for fast data analysis.

Biogeochemical control of marine productivity in the Mediterranean Sea during the last 50 years

PubMed Central

Macias, Diego; Garcia-Gorriz, Elisa; Piroddi, Chiara; Stips, Adolf

2014-01-01

The temporal dynamics of biogeochemical variables derived from a coupled 3-D model of the Mediterranean Sea are evaluated for the last 50 years (1960–2010) against independent data on fisheries catch per unit effort (CPUE) for the same time period. Concordant patterns are found in the time series of all of the biological variables (from the model and from fisheries statistics), with low values at the beginning of the series, a later increase, with maximum levels reached at the end of the 1990s, and a posterior stabilization. Spectral analysis of the annual biological time series reveals coincident low-frequency signals in all of them. The first, more energetic signal peaks around the year 2000, while the second, less energetic signal peaks near 1982. Almost identical low-frequency signals are found in the nutrient loads of the rivers and in the integrated nutrient levels in the surface marine ecosystem. Nitrate concentration shows a maximum level in 1998, with a later stabilization to present-day values, coincident with the first low-frequency signal found in the biological series. Phosphate shows maximum concentrations around 1982 and a posterior sharp decline, in concordance with the second low-frequency signal observed in the biological series. That result seems to indicate that the control of marine productivity (plankton to fish) in the Mediterranean is principally mediated through bottom-up processes that could be traced back to the characteristics of riverine discharges. The high sensitivity of CPUE time series to environmental conditions might be another indicator of the overexploitation of this marine ecosystem. Key Points Biogeochemical evolution of the Mediterranean over the past 50 years River nutrient loads drive primary and secondary productions Strong link between low trophic levels and fisheries PMID:26180286

Efficiency of autonomous soft nanomachines at maximum power.

PubMed

Seifert, Udo

2011-01-14

We consider nanosized artificial or biological machines working in steady state enforced by imposing nonequilibrium concentrations of solutes or by applying external forces, torques, or electric fields. For unicyclic and strongly coupled multicyclic machines, efficiency at maximum power is not bounded by the linear response value 1/2. For strong driving, it can even approach the thermodynamic limit 1. Quite generally, such machines fall into three different classes characterized, respectively, as "strong and efficient," "strong and inefficient," and "balanced." For weakly coupled multicyclic machines, efficiency at maximum power has lost any universality even in the linear response regime.

Small passenger car transmission test; Chevrolet LUV transmission

NASA Technical Reports Server (NTRS)

Bujold, M. P.

1980-01-01

A 1978 Chevrolet LUV manual transmission tested per the applicable portions of a passenger car automatic transmission test code (SAE J65lb) which required drive performance, coast performance, and no load test conditions. Under these test conditions, the transmission attained maximum efficiencies in the upper ninety percent range for both drive performance tests and coast performance tests. The major results of this test (torque, speed, and efficiency curves) are presented. Graphs map the complete performance characteristics for the Chevrolet LUV transmission.

Small passenger car transmission test; Ford C4 transmission

NASA Technical Reports Server (NTRS)

Bujold, M. P.

1980-01-01

A 1979 Ford C4 automatic transmission was tested per a passenger car automatic transmission test code (SAE J651b) which required drive performance, coast performance, and no load test conditions. Under these test conditions, the transmission attained maximum efficiencies in the mid-eighty percent range for both drive performance tests and coast performance tests. The major results of this test (torque, speed, and efficiency curves) are presented. Graphs map the complete performance characteristics for the Ford C4 transmission.

Small passenger car transmission test: Mercury Lynx ATX transmission

NASA Technical Reports Server (NTRS)

Bujold, M. P.

1981-01-01

The testing of a Mercury Lynx automatic transmission is reported. The transmission was tested in accordance with a passenger car automatic transmission test code (SAE J65lb) which required drive performance, coast performance, and no load test conditions. Under these conditions, the transmission attained maximum efficiencies in the mid-ninety percent range both for drive performance test and coast performance tests. The torque, speed, and efficiency curves are presented, which provide the complete performance characteristics for the Mercury Lynx automatic transmission.

Delay compensation - Its effect in reducing sampling errors in Fourier spectroscopy

NASA Technical Reports Server (NTRS)

Zachor, A. S.; Aaronson, S. M.

1979-01-01

An approximate formula is derived for the spectrum ghosts caused by periodic drive speed variations in a Michelson interferometer. The solution represents the case of fringe-controlled sampling and is applicable when the reference fringes are delayed to compensate for the delay introduced by the electrical filter in the signal channel. Numerical results are worked out for several common low-pass filters. It is shown that the maximum relative ghost amplitude over the range of frequencies corresponding to the lower half of the filter band is typically 20 times smaller than the relative zero-to-peak velocity error, when delayed sampling is used. In the lowest quarter of the filter band it is more than 100 times smaller than the relative velocity error. These values are ten and forty times smaller, respectively, than they would be without delay compensation if the filter is a 6-pole Butterworth.

Driving Method for Compensating Reliability Problem of Hydrogenated Amorphous Silicon Thin Film Transistors and Image Sticking Phenomenon in Active Matrix Organic Light-Emitting Diode Displays

NASA Astrophysics Data System (ADS)

Shin, Min-Seok; Jo, Yun-Rae; Kwon, Oh-Kyong

2011-03-01

In this paper, we propose a driving method for compensating the electrical instability of hydrogenated amorphous silicon (a-Si:H) thin film transistors (TFTs) and the luminance degradation of organic light-emitting diode (OLED) devices for large active matrix OLED (AMOLED) displays. The proposed driving method senses the electrical characteristics of a-Si:H TFTs and OLEDs using current integrators and compensates them by an external compensation method. Threshold voltage shift is controlled a using negative bias voltage. After applying the proposed driving method, the measured error of the maximum emission current ranges from -1.23 to +1.59 least significant bit (LSB) of a 10-bit gray scale under the threshold voltage shift ranging from -0.16 to 0.17 V.

Comparison of hydrodynamic simulations with two-shockwave drive target experiments

NASA Astrophysics Data System (ADS)

Karkhanis, Varad; Ramaprabhu, Praveen; Buttler, William

2015-11-01

We consider hydrodynamic continuum simulations to mimic ejecta generation in two-shockwave target experiments, where metallic surface is loaded by two successive shock waves. Time of second shock in simulations is determined to match experimental amplitudes at the arrival of the second shock. The negative Atwood number (A --> - 1) of ejecta simulations leads to two successive phase inversions of the interface corresponding to the passage of the shocks from heavy to light media in each instance. Metallic phase of ejecta (solid/liquid) depends on shock loading pressure in the experiment, and we find that hydrodynamic simulations quantify the liquid phase ejecta physics with a fair degree of accuracy, where RM instability is not suppressed by the strength effect. In particular, we find that our results of free surface velocity, maximum ejecta velocity, and maximum ejecta areal density are in excellent agreement with their experimental counterparts, as well as ejecta models. We also comment on the parametric space for hydrodynamic simulations in which they can be used to compare with the target experiments.

Cosmic equilibration: A holographic no-hair theorem from the generalized second law

NASA Astrophysics Data System (ADS)

Carroll, Sean M.; Chatwin-Davies, Aidan

2018-02-01

In a wide class of cosmological models, a positive cosmological constant drives cosmological evolution toward an asymptotically de Sitter phase. Here we connect this behavior to the increase of entropy over time, based on the idea that de Sitter spacetime is a maximum-entropy state. We prove a cosmic no-hair theorem for Robertson-Walker and Bianchi I spacetimes that admit a Q-screen ("quantum" holographic screen) with certain entropic properties: If generalized entropy, in the sense of the cosmological version of the generalized second law conjectured by Bousso and Engelhardt, increases up to a finite maximum value along the screen, then the spacetime is asymptotically de Sitter in the future. Moreover, the limiting value of generalized entropy coincides with the de Sitter horizon entropy. We do not use the Einstein field equations in our proof, nor do we assume the existence of a positive cosmological constant. As such, asymptotic relaxation to a de Sitter phase can, in a precise sense, be thought of as cosmological equilibration.

The universal instability in general geometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Helander, P.; Plunk, G. G.

2015-09-15

The “universal” instability has recently been revived by Landreman et al. [Phys. Rev. Lett. 114, 095003 (2015)], who showed that it indeed exists in plasma geometries with straight (but sheared) magnetic field lines. Here, it is demonstrated analytically that this instability can be presented in more general sheared and toroidal geometries. In a torus, the universal instability is shown to be closely related to the trapped-electron mode, although the trapped-electron drive is usually dominant. However, this drive can be weakened or eliminated, as in the case in stellarators with the maximum-J property, leaving the parallel Landau resonance to drive amore » residual mode, which is identified as the universal instability.« less

Transport of particles and microorganisms in microfluidic channels using rectified ac electro-osmotic flow

PubMed Central

Wu, Wen-I; Selvaganapathy, P. Ravi; Ching, Chan Y.

2011-01-01

A new method is demonstrated to transport particles, cells, and other microorganisms using rectified ac electro-osmotic flows in open microchannels. The rectified flow is obtained by synchronous zeta potential modulation with the driving potential in the microchannel. Experiments were conducted to transport both neutral, charged particles, and microorganisms of various sizes. A maximum speed of 50 μm∕s was obtained for 8 μm polystyrene beads, without any electrolysis, using a symmetrical square waveform driving electric field of 5 V∕mm at 10 Hz and a 360 V gate potential with its polarity synchronized with the driving potential (phase lag=0°). PMID:21522497

Theory of electric creep and electromechanical coupling with domain evolution for non-poled and fully poled ferroelectric ceramics

PubMed Central

Xia, Xiaodong; Wang, Yang; Zhong, Zheng

2016-01-01

Unlike mechanical creep with inelastic deformation, electric creep with domain evolution is a rarely studied subject. In this paper, we present a theory of electric creep and related electromechanical coupling for both non-poled and fully poled ferroelectric ceramics. We consider electric creep to be a time-dependent process, with an initial condition lying on the D (electric displacement) versus E (electric field) hysteresis loop. Both processes are shown to share the same Gibbs free energy and thermodynamic driving force, but relative to creep, the hysteresis loop is just a field-dependent process. With this view, we develop a theory with a single thermodynamic driving force but with two separate kinetic equations, one for the field-dependent loops in terms of a Lorentzian-like function and the other for the time-dependent D in terms of a dissipation potential. We use the 0°–90° and then 90°–180° switches to attain these goals. It is demonstrated that the calculated results are in broad agreement with two sets of experiments, one for a non-poled PIC-151 and the other for a fully poled PZT-5A. The theory also shows that creep polarization tends to reach a saturation state with time and that the saturated polarization has its maximum at the coercive field. PMID:27843406

Transport time and care processes for patients transferred with ST-segment-elevation myocardial infarction: the reperfusion in acute myocardial infarction in Carolina emergency rooms experience.

PubMed

Muñoz, Daniel; Roettig, Mayme L; Monk, Lisa; Al-Khalidi, Hussein; Jollis, James G; Granger, Christopher B

2012-08-01

For patients with ST-segment elevation myocardial infarction transferred for primary percutaneous coronary intervention, guidelines have called for device activation within 90 minutes of initial presentation. Fewer than 20% of transferred patients are treated in such a timely fashion. We examine the association between transfer drive times and door-to-device (D2D) times in a network of North Carolina hospitals. We compare the feasibility of timely percutaneous coronary intervention using ground versus air transfer. We perform a retrospective analysis of the relationship between transfer drive times and D2D times in a 119-hospital ST-segment-elevation myocardial infarction statewide network. Between July 2008 and December 2009, 1537 ST-segment-elevation myocardial infarction patients underwent interhospital transfer for reperfusion via primary percutaneous coronary intervention. For ground transfers, median D2D time was 93 minutes for drive times ≤30 minutes, 117 minutes for drive times of 31 to 45 minutes, and 121 minutes for drive times >45 minutes. For air transfers, median D2D time was 125 minutes for drive times of 31 to 45 minutes and 138 minutes for drive times >45 minutes. Helicopter transport was associated with longer door-in door-out times and, ultimately, was associated with median D2D times that exceeded guideline recommendations, no matter the transfer drive time category. In a well-developed ST-segment-elevation myocardial infarction system, D2D times within 90 to 120 minutes appear most feasible for hospitals within 30-minute transfer drive time. Helicopter transport did not offer D2D time advantages for transferred STEMI patients. This finding appears to be attributable to comparably longer door-in door-out times for air transfers.

Relationships between frequency of driving under the influence of cannabis, self-reported reckless driving and risk-taking behavior observed in a driving simulator.

PubMed

Bergeron, Jacques; Paquette, Martin

2014-06-01

The role of cannabis consumption in traffic crashes is unclear and the causal link between cannabis and collisions is still to be demonstrated. While cannabis use is very likely to impair driving ability, there is as yet no overwhelming evidence that cannabis use in isolation contributes more to collisions than other characteristics inherent to cannabis users. As noted in a growing body of literature, individuals driving under the influence of cannabis (DUIC) seem to exhibit a general reckless driving style putting them at higher risk to be involved in traffic crashes. This study aims at investigating the relationship between self-reported DUIC and reckless driving by means of self-reported measures and direct observations made in a driving simulator. Participants (n=72) were required to be between 18 and 25 years of age, to hold a valid driver's license, and to drive at least twice a week. They completed standard driving simulation tasks recreating everyday on-road trivial conditions. Results show that people admitting that they commit more real-life dangerous driving behaviors reached higher maximum speed and demonstrated more reckless driving behaviors on the driving simulation tasks. Self-reported DUIC is associated with a risky driving style including a broad range of reckless on-road behaviors and support the problem driving behavior theory. Moreover, beyond confounding factors, both self-report DUIC and observed dangerous behaviors are associated with real-life traffic violations. Since DUIC appears to be related to an overall reckless style of driving, it is proposed that public safety policies should be more holistic, simultaneously targeting multiple on-road dangerous behaviors for intervention. Copyright © 2014 Elsevier B.V. All rights reserved.

Ultraviolet Spectrometer and Polarimeter (UVSP) software development and hardware tests for the solar maximum mission

NASA Technical Reports Server (NTRS)

1984-01-01

An analysis of UVSP wavelength drive hardware, problems, and recovery procedures; radiative power loss from solar plasmas; and correlations between observed UV brightness and inferred photospheric currents are given.

Equilibrium evolution in oscillating-field current-drive experiments

NASA Astrophysics Data System (ADS)

McCollam, K. J.; Anderson, J. K.; Blair, A. P.; Craig, D.; Den Hartog, D. J.; Ebrahimi, F.; O'Connell, R.; Reusch, J. A.; Sarff, J. S.; Stephens, H. D.; Stone, D. R.; Brower, D. L.; Deng, B. H.; Ding, W. X.

2010-08-01

Oscillating-field current drive (OFCD) is a proposed method of steady-state toroidal plasma sustainment in which ac poloidal and toroidal loop voltages are applied to produce a dc plasma current. OFCD is added to standard, inductively sustained reversed-field pinch plasmas in the Madison Symmetric Torus [R. N. Dexter et al., Fusion Technol. 19, 131 (1991)]. Equilibrium profiles and fluctuations during a single cycle are measured and analyzed for different relative phases between the two OFCD voltages and for OFCD off. For OFCD phases leading to the most added plasma current, the measured energy confinement is slightly better than that for OFCD off. By contrast, the phase of the maximum OFCD helicity-injection rate also has the maximum decay rate, which is ascribed to transport losses during discrete magnetic-fluctuation events induced by OFCD. Resistive-magnetohydrodynamic simulations of the experiments reproduce the observed phase dependence of the added current.

The effects of a single session of spinal manipulation on strength and cortical drive in athletes.

PubMed

Christiansen, Thomas Lykke; Niazi, Imran Khan; Holt, Kelly; Nedergaard, Rasmus Wiberg; Duehr, Jens; Allen, Kathryn; Marshall, Paul; Türker, Kemal S; Hartvigsen, Jan; Haavik, Heidi

2018-04-01

The primary purpose of this study was to investigate whether a single session of spinal manipulation (SM) increases strength and cortical drive in the lower limb (soleus muscle) of elite Taekwondo athletes. Soleus-evoked V-waves, H-reflex and maximum voluntary contraction (MVC) of the plantar flexors were recorded from 11 elite Taekwondo athletes using a randomized controlled crossover design. Interventions were either SM or passive movement control. Outcomes were assessed at pre-intervention and at three post-intervention time periods (immediate post, post 30 min and post 60 min). A multifactorial repeated measures ANOVA was conducted to assess within and between group differences. Time and session were used as factors. A post hoc analysis was carried out, when an interactive effect was present. Significance was set at p ≤ 0.05. SM increased MVC force [F(3,30) = 5.95, p < 0.01], and V-waves [F(3,30) = 4.25, p = 0.01] over time compared to the control intervention. Between group differences were significant for all time periods (p < 0.05) except for the post60 force measurements (p = 0.07). A single session of SM increased muscle strength and corticospinal excitability to ankle plantar flexor muscles in elite Taekwondo athletes. The increased MVC force lasted for 30 min and the corticospinal excitability increase persisted for at least 60 min.

Shock drive capabilities of a 30-Joule laser at the matter in extreme conditions hutch of the Linac Coherent Light Source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Shaughnessy Brennan; Hashim, Akel; Gleason, Arianna

In this paper, we measure the shock drive capabilities of a 30 J, nanosecond, 527 nm laser system at the matter in extreme conditions hutch of the Linac Coherent Light Source. Using a velocity interferometer system for any reflector, we ascertain the maximum instantaneous ablation pressure and characterize its dependence on a drive laser spot size, spatial profile, and temporal profile. We also examine the effects of these parameters on shock spatial and temporal uniformity. Our analysis shows the drive laser capable of generating instantaneous ablation pressures exceeding 160 GPa while maintaining a 1D shock profile. We find that slopemore » pulses provide higher instantaneous ablation pressures than plateau pulses. Our results show instantaneous ablation pressures comparable to those measured at the Omega Laser Facility in Rochester, NY under similar optical drive parameters. In conclusion, we analyze how optical laser ablation pressures are compare with known scaling relations, accounting for variable laser wavelengths.« less

Shock drive capabilities of a 30-Joule laser at the matter in extreme conditions hutch of the Linac Coherent Light Source

DOE PAGES

Brown, Shaughnessy Brennan; Hashim, Akel; Gleason, Arianna; ...

2017-10-23

In this paper, we measure the shock drive capabilities of a 30 J, nanosecond, 527 nm laser system at the matter in extreme conditions hutch of the Linac Coherent Light Source. Using a velocity interferometer system for any reflector, we ascertain the maximum instantaneous ablation pressure and characterize its dependence on a drive laser spot size, spatial profile, and temporal profile. We also examine the effects of these parameters on shock spatial and temporal uniformity. Our analysis shows the drive laser capable of generating instantaneous ablation pressures exceeding 160 GPa while maintaining a 1D shock profile. We find that slopemore » pulses provide higher instantaneous ablation pressures than plateau pulses. Our results show instantaneous ablation pressures comparable to those measured at the Omega Laser Facility in Rochester, NY under similar optical drive parameters. In conclusion, we analyze how optical laser ablation pressures are compare with known scaling relations, accounting for variable laser wavelengths.« less

Relationship Between Selected Strength and Power Assessments to Peak and Average Velocity of the Drive Block in Offensive Line Play.

PubMed

Jacobson, Bert H; Conchola, Eric C; Smith, Doug B; Akehi, Kazuma; Glass, Rob G

2016-08-01

Jacobson, BH, Conchola, EC, Smith, DB, Akehi, K, and Glass, RG. Relationship between selected strength and power assessments to peak and average velocity of the drive block in offensive line play. J Strength Cond Res 30(8): 2202-2205, 2016-Typical strength training for football includes the squat and power clean (PC) and routinely measured variables include 1 repetition maximum (1RM) squat and 1RM PC along with the vertical jump (VJ) for power. However, little research exists regarding the association between the strength exercises and velocity of an actual on-the-field performance. The purpose of this study was to investigate the relationship of peak velocity (PV) and average velocity (AV) of the offensive line drive block to 1RM squat, 1RM PC, the VJ, body mass (BM), and body composition. One repetition maximum assessments for the squat and PC were recorded along with VJ height, BM, and percent body fat. These data were correlated with PV and AV while performing the drive block. Peal velocity and AV were assessed using a Tendo Power and Speed Analyzer as the linemen fired, from a 3-point stance into a stationary blocking dummy. Pearson product analysis yielded significant (p ≤ 0.05) correlations between PV and AV and the VJ, the squat, and the PC. A significant inverse association was found for both PV and AV and body fat. These data help to confirm that the typical exercises recommended for American football linemen is positively associated with both PV and AV needed for the drive block effectiveness. It is recommended that these exercises remain the focus of a weight room protocol and that ancillary exercises be built around these exercises. Additionally, efforts to reduce body fat are recommended.

The iterative thermal emission method: A more implicit modification of IMC

NASA Astrophysics Data System (ADS)

Long, A. R.; Gentile, N. A.; Palmer, T. S.

2014-11-01

For over 40 years, the Implicit Monte Carlo (IMC) method has been used to solve challenging problems in thermal radiative transfer. These problems typically contain regions that are optically thick and diffusive, as a consequence of the high degree of ;pseudo-scattering; introduced to model the absorption and reemission of photons from a tightly-coupled, radiating material. IMC has several well-known features that could be improved: a) it can be prohibitively computationally expensive, b) it introduces statistical noise into the material and radiation temperatures, which may be problematic in multiphysics simulations, and c) under certain conditions, solutions can be nonphysical, in that they violate a maximum principle, where IMC-calculated temperatures can be greater than the maximum temperature used to drive the problem. We have developed a variant of IMC called iterative thermal emission IMC, which is designed to have a reduced parameter space in which the maximum principle is violated. ITE IMC is a more implicit version of IMC in that it uses the information obtained from a series of IMC photon histories to improve the estimate for the end of time step material temperature during a time step. A better estimate of the end of time step material temperature allows for a more implicit estimate of other temperature-dependent quantities: opacity, heat capacity, Fleck factor (probability that a photon absorbed during a time step is not reemitted) and the Planckian emission source. We have verified the ITE IMC method against 0-D and 1-D analytic solutions and problems from the literature. These results are compared with traditional IMC. We perform an infinite medium stability analysis of ITE IMC and show that it is slightly more numerically stable than traditional IMC. We find that significantly larger time steps can be used with ITE IMC without violating the maximum principle, especially in problems with non-linear material properties. The ITE IMC method does however yield solutions with larger variance because each sub-step uses a different Fleck factor (even at equilibrium).

The iterative thermal emission method: A more implicit modification of IMC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Long, A.R., E-mail: arlong.ne@tamu.edu; Gentile, N.A.; Palmer, T.S.

2014-11-15

For over 40 years, the Implicit Monte Carlo (IMC) method has been used to solve challenging problems in thermal radiative transfer. These problems typically contain regions that are optically thick and diffusive, as a consequence of the high degree of “pseudo-scattering” introduced to model the absorption and reemission of photons from a tightly-coupled, radiating material. IMC has several well-known features that could be improved: a) it can be prohibitively computationally expensive, b) it introduces statistical noise into the material and radiation temperatures, which may be problematic in multiphysics simulations, and c) under certain conditions, solutions can be nonphysical, in thatmore » they violate a maximum principle, where IMC-calculated temperatures can be greater than the maximum temperature used to drive the problem. We have developed a variant of IMC called iterative thermal emission IMC, which is designed to have a reduced parameter space in which the maximum principle is violated. ITE IMC is a more implicit version of IMC in that it uses the information obtained from a series of IMC photon histories to improve the estimate for the end of time step material temperature during a time step. A better estimate of the end of time step material temperature allows for a more implicit estimate of other temperature-dependent quantities: opacity, heat capacity, Fleck factor (probability that a photon absorbed during a time step is not reemitted) and the Planckian emission source. We have verified the ITE IMC method against 0-D and 1-D analytic solutions and problems from the literature. These results are compared with traditional IMC. We perform an infinite medium stability analysis of ITE IMC and show that it is slightly more numerically stable than traditional IMC. We find that significantly larger time steps can be used with ITE IMC without violating the maximum principle, especially in problems with non-linear material properties. The ITE IMC method does however yield solutions with larger variance because each sub-step uses a different Fleck factor (even at equilibrium)« less

High breakdown voltage and high driving current in a novel silicon-on-insulator MESFET with high- and low-resistance boxes in the drift region

NASA Astrophysics Data System (ADS)

Naderi, Ali; Mohammadi, Hamed

2018-06-01

In this paper a novel silicon-on-insulator metal oxide field effect transistor (SOI-MESFET) with high- and low-resistance boxes (HLRB) is proposed. This structure increases the current and breakdown voltage, simultaneously. The semiconductor at the source side of the channel is doped with higher impurity than the other parts to reduce its resistance and increase the driving current as low-resistance box. An oxide box is implemented at the upper part of the channel from the drain region toward the middle of the channel as the high-resistance box. Inserting a high-resistance box increases the breakdown voltage and improves the RF performance of the device because of its higher tolerable electric field and modification in gate-drain capacitance, respectively. The high-resistance region reduces the current density of the device which is completely compensated by low-resistance box. A 92% increase in breakdown voltage and an 11% improvement in the device current have been obtained. Also, maximum oscillation frequency, unilateral power gain, maximum available gain, maximum stable gain, and maximum output power density are improved by 7%, 35%, 23%, 26%, and 150%, respectively. These results show that the HLRB-SOI-MESFET can be considered as a candidate to replace Conventional SOI-MESFET (C-SOI-MESFET) for high-voltage and high-frequency applications.

Hydraulic limits on maximum plant transpiration and the emergence of the safety-efficiency trade-off.

PubMed

Manzoni, Stefano; Vico, Giulia; Katul, Gabriel; Palmroth, Sari; Jackson, Robert B; Porporato, Amilcare

2013-04-01

Soil and plant hydraulics constrain ecosystem productivity by setting physical limits to water transport and hence carbon uptake by leaves. While more negative xylem water potentials provide a larger driving force for water transport, they also cause cavitation that limits hydraulic conductivity. An optimum balance between driving force and cavitation occurs at intermediate water potentials, thus defining the maximum transpiration rate the xylem can sustain (denoted as E(max)). The presence of this maximum raises the question as to whether plants regulate transpiration through stomata to function near E(max). To address this question, we calculated E(max) across plant functional types and climates using a hydraulic model and a global database of plant hydraulic traits. The predicted E(max) compared well with measured peak transpiration across plant sizes and growth conditions (R = 0.86, P < 0.001) and was relatively conserved among plant types (for a given plant size), while increasing across climates following the atmospheric evaporative demand. The fact that E(max) was roughly conserved across plant types and scales with the product of xylem saturated conductivity and water potential at 50% cavitation was used here to explain the safety-efficiency trade-off in plant xylem. Stomatal conductance allows maximum transpiration rates despite partial cavitation in the xylem thereby suggesting coordination between stomatal regulation and xylem hydraulic characteristics. © 2013 The Authors. New Phytologist © 2013 New Phytologist Trust.

Foam flow in a model porous medium: I. The effect of foam coarsening.

PubMed

Jones, S A; Getrouw, N; Vincent-Bonnieu, S

2018-05-09

Foam structure evolves with time due to gas diffusion between bubbles (coarsening). In a bulk foam, coarsening behaviour is well defined, but there is less understanding of coarsening in confined geometries such as porous media. Previous predictions suggest that coarsening will cause foam lamellae to move to low energy configurations in the pore throats, resulting in greater capillary resistance when restarting flow. Foam coarsening experiments were conducted in both a model-porous-media micromodel and in a sandstone core. In both cases, foam was generated by coinjecting surfactant solution and nitrogen. Once steady state flow had been achieved, the injection was stopped and the system sealed off. In the micromodel, the foam coarsening was recorded using time-lapse photography. In the core flood, the additional driving pressure required to reinitiate flow after coarsening was measured. In the micromodel the bubbles coarsened rapidly to the pore size. At the completion of coarsening the lamellae were located in minimum energy configurations in the pore throats. The wall effect meant that the coarsening did not conform to the unconstricted growth laws. The coreflood tests also showed coarsening to be a rapid process. The additional driving pressure to restart flow reached a maximum after just 2 minutes.

Method of electric powertrain matching for battery-powered electric cars

NASA Astrophysics Data System (ADS)

Ning, Guobao; Xiong, Lu; Zhang, Lijun; Yu, Zhuoping

2013-05-01

The current match method of electric powertrain still makes use of longitudinal dynamics, which can't realize maximum capacity for on-board energy storage unit and can't reach lowest equivalent fuel consumption as well. Another match method focuses on improving available space considering reasonable layout of vehicle to enlarge rated energy capacity for on-board energy storage unit, which can keep the longitudinal dynamics performance almost unchanged but can't reach lowest fuel consumption. Considering the characteristics of driving motor, method of electric powertrain matching utilizing conventional longitudinal dynamics for driving system and cut-and-try method for energy storage system is proposed for passenger cars converted from traditional ones. Through combining the utilization of vehicle space which contributes to the on-board energy amount, vehicle longitudinal performance requirements, vehicle equivalent fuel consumption level, passive safety requirements and maximum driving range requirement together, a comprehensive optimal match method of electric powertrain for battery-powered electric vehicle is raised. In simulation, the vehicle model and match method is built in Matlab/simulink, and the Environmental Protection Agency (EPA) Urban Dynamometer Driving Schedule (UDDS) is chosen as a test condition. The simulation results show that 2.62% of regenerative energy and 2% of energy storage efficiency are increased relative to the traditional method. The research conclusions provide theoretical and practical solutions for electric powertrain matching for modern battery-powered electric vehicles especially for those converted from traditional ones, and further enhance dynamics of electric vehicles.

A Solar Cycle Dependence of Nonlinearity in Magnetospheric Activity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Jay R; Wing, Simon

2005-03-08

The nonlinear dependencies inherent to the historical K(sub)p data stream (1932-2003) are examined using mutual information and cumulant based cost as discriminating statistics. The discriminating statistics are compared with surrogate data streams that are constructed using the corrected amplitude adjustment Fourier transform (CAAFT) method and capture the linear properties of the original K(sub)p data. Differences are regularly seen in the discriminating statistics a few years prior to solar minima, while no differences are apparent at the time of solar maximum. These results suggest that the dynamics of the magnetosphere tend to be more linear at solar maximum than at solarmore » minimum. The strong nonlinear dependencies tend to peak on a timescale around 40-50 hours and are statistically significant up to one week. Because the solar wind driver variables, VB(sub)s and dynamical pressure exhibit a much shorter decorrelation time for nonlinearities, the results seem to indicate that the nonlinearity is related to internal magnetospheric dynamics. Moreover, the timescales for the nonlinearity seem to be on the same order as that for storm/ring current relaxation. We suggest that the strong solar wind driving that occurs around solar maximum dominates the magnetospheric dynamics suppressing the internal magnetospheric nonlinearity. On the other hand, in the descending phase of the solar cycle just prior to solar minimum, when magnetospheric activity is weaker, the dynamics exhibit a significant nonlinear internal magnetospheric response that may be related to increased solar wind speed.« less

Enhanced reproducibility of L-mode plasma discharges via physics-model-based q-profile feedback control in DIII-D

NASA Astrophysics Data System (ADS)

Schuster, E.; Wehner, W. P.; Barton, J. E.; Boyer, M. D.; Luce, T. C.; Ferron, J. R.; Holcomb, C. T.; Walker, M. L.; Humphreys, D. A.; Solomon, W. M.; Penaflor, B. G.; Johnson, R. D.

2017-11-01

Recent experiments on DIII-D demonstrate the potential of physics-model-based q-profile control to improve reproducibility of plasma discharges. A combined feedforward  +  feedback control scheme is employed to optimize the current ramp-up phase by consistently achieving target q profiles (Target 1: q_min=1.3, q95=4.4 ; Target 2: q_min=1.65, q95=5.0 ; Target 3: q_min=2.1, q95=6.2 ) at prescribed times during the plasma formation phase (Target 1: t=1.5 s; Target 2: t=1.3 s; Target 3: t=1.0 s). At the core of the control scheme is a nonlinear, first-principles-driven, physics-based, control-oriented model of the plasma dynamics valid for low confinement (L-mode) scenarios. To prevent undesired L-H transitions, a constraint on the maximum allowable total auxiliary power is imposed in addition to the maximum powers for the individual heating and current-drive sources. Experimental results are presented to demonstrate the effectiveness of the combined feedforward  +  feedback control scheme to consistently achieve the desired target profiles at the predefined times. These results also show how the addition of feedback control significantly improves upon the feedforward-only control solution by reducing the matching error and also how the feedback controller is able to reduce the matching error as the constraint on the maximum allowable total auxiliary power is relaxed while keeping the plasma in L-mode.

Drunk driving detection based on classification of multivariate time series.

PubMed

Li, Zhenlong; Jin, Xue; Zhao, Xiaohua

2015-09-01

This paper addresses the problem of detecting drunk driving based on classification of multivariate time series. First, driving performance measures were collected from a test in a driving simulator located in the Traffic Research Center, Beijing University of Technology. Lateral position and steering angle were used to detect drunk driving. Second, multivariate time series analysis was performed to extract the features. A piecewise linear representation was used to represent multivariate time series. A bottom-up algorithm was then employed to separate multivariate time series. The slope and time interval of each segment were extracted as the features for classification. Third, a support vector machine classifier was used to classify driver's state into two classes (normal or drunk) according to the extracted features. The proposed approach achieved an accuracy of 80.0%. Drunk driving detection based on the analysis of multivariate time series is feasible and effective. The approach has implications for drunk driving detection. Copyright © 2015 Elsevier Ltd and National Safety Council. All rights reserved.

Performance testing of collision-avoidance system for power wheelchairs.

PubMed

Lopresti, Edmund F; Sharma, Vinod; Simpson, Richard C; Mostowy, L Casimir

2011-01-01

The Drive-Safe System (DSS) is a collision-avoidance system for power wheelchairs designed to support people with mobility impairments who also have visual, upper-limb, or cognitive impairments. The DSS uses a distributed approach to provide an add-on, shared-control, navigation-assistance solution. In this project, the DSS was tested for engineering goals such as sensor coverage, maximum safe speed, maximum detection distance, and power consumption while the wheelchair was stationary or driven by an investigator. Results indicate that the DSS provided uniform, reliable sensor coverage around the wheelchair; detected obstacles as small as 3.2 mm at distances of at least 1.6 m; and attained a maximum safe speed of 4.2 km/h. The DSS can drive reliably as close as 15.2 cm from a wall, traverse doorways as narrow as 81.3 cm without interrupting forward movement, and reduce wheelchair battery life by only 3%. These results have implications for a practical system to support safe, independent mobility for veterans who acquire multiple disabilities during Active Duty or later in life. These tests indicate that a system utilizing relatively low cost ultrasound, infrared, and force sensors can effectively detect obstacles in the vicinity of a wheelchair.

Temporal profile of prolonged, night-time driving performance: breaks from driving temporarily reduce time-on-task fatigue but not sleepiness.

PubMed

Phipps-Nelson, Jo; Redman, Jennifer R; Rajaratnam, Shantha M W

2011-09-01

Breaks are often used by drivers to counteract sleepiness and time-on-task fatigue during prolonged driving. We examined the temporal profile of changes in driving performance, electroencephalogram (EEG) activity and subjective measures of sleepiness and fatigue during prolonged nocturnal driving in a car simulator. In addition, the study examined the impact of regular breaks from driving on performance, sleepiness and fatigue. Healthy volunteers (n=12, 23-45 years) maintained a regular sleep-wake pattern for 14 days and were then in a laboratory from 21:00 to 08:30 hours. The driving simulator scene was designed to simulate monotonous night-time rural driving. Participants drove 4 × 2-h test sessions, with a break from driving of 1 h between each session. During the break participants performed tests assessing sleepiness and fatigue, and psychomotor performance (~30 mins), and then were permitted to sit quietly. They were monitored for wakefulness, and not permitted to nap or ingest caffeine. EEG was recorded during the driving task, and subjective assessments of sleepiness and fatigue were obtained at the start and completion of each session. We found that driving performance deteriorated (2.5-fold), EEG delta, theta and alpha activity increased, and subjective sleepiness and fatigue ratings increased across the testing period. Driving performance and fatigue ratings improved following the scheduled breaks from driving, while the breaks did not affect EEG activity and subjective sleepiness. Time-on-task effects increased through the testing period, indicating that these effects are exacerbated by increasing sleepiness. Breaks from driving without sleep temporarily ameliorate time-on-task fatigue, but provide little benefit to the sleepy driver. © 2010 European Sleep Research Society.

Torque-based optimal acceleration control for electric vehicle

NASA Astrophysics Data System (ADS)

Lu, Dongbin; Ouyang, Minggao

2014-03-01

The existing research of the acceleration control mainly focuses on an optimization of the velocity trajectory with respect to a criterion formulation that weights acceleration time and fuel consumption. The minimum-fuel acceleration problem in conventional vehicle has been solved by Pontryagin's maximum principle and dynamic programming algorithm, respectively. The acceleration control with minimum energy consumption for battery electric vehicle(EV) has not been reported. In this paper, the permanent magnet synchronous motor(PMSM) is controlled by the field oriented control(FOC) method and the electric drive system for the EV(including the PMSM, the inverter and the battery) is modeled to favor over a detailed consumption map. The analytical algorithm is proposed to analyze the optimal acceleration control and the optimal torque versus speed curve in the acceleration process is obtained. Considering the acceleration time, a penalty function is introduced to realize a fast vehicle speed tracking. The optimal acceleration control is also addressed with dynamic programming(DP). This method can solve the optimal acceleration problem with precise time constraint, but it consumes a large amount of computation time. The EV used in simulation and experiment is a four-wheel hub motor drive electric vehicle. The simulation and experimental results show that the required battery energy has little difference between the acceleration control solved by analytical algorithm and that solved by DP, and is greatly reduced comparing with the constant pedal opening acceleration. The proposed analytical and DP algorithms can minimize the energy consumption in EV's acceleration process and the analytical algorithm is easy to be implemented in real-time control.

Life analysis of multiroller planetary traction drive

NASA Technical Reports Server (NTRS)

Coy, J. J.; Rohn, D. A.; Loewenthal, S. H.

1981-01-01

A contact fatigue life analysis was performed for a constant ratio, Nasvytis Multiroller Traction Drive. The analysis was based on the Lundberg-Palmgren method for rolling element bearing life prediction. Life adjustment factors for materials, processing, lubrication and traction were included. The 14.7 to 1 ratio drive consisted of a single stage planetary configuration with two rows of stepped planet rollers of five rollers per row, having a roller cluster diameter of approximately 0.21 m, a width of 0.06 m and a weight of 9 kg. Drive system 10 percent life ranged from 18,800 hours at 16.6 kW (22.2 hp) and 25,000 rpm sun roller speed, to 305 hours at maximum operating conditions of 149 kw (200 hp) and 75,000 rpm sun roller speed. The effect of roller diameter and roller center location on life were determined. It was found that an optimum life geometry exists.

Estimating Driving Performance Based on EEG Spectrum Analysis

NASA Astrophysics Data System (ADS)

Lin, Chin-Teng; Wu, Ruei-Cheng; Jung, Tzyy-Ping; Liang, Sheng-Fu; Huang, Teng-Yi

2005-12-01

The growing number of traffic accidents in recent years has become a serious concern to society. Accidents caused by driver's drowsiness behind the steering wheel have a high fatality rate because of the marked decline in the driver's abilities of perception, recognition, and vehicle control abilities while sleepy. Preventing such accidents caused by drowsiness is highly desirable but requires techniques for continuously detecting, estimating, and predicting the level of alertness of drivers and delivering effective feedbacks to maintain their maximum performance. This paper proposes an EEG-based drowsiness estimation system that combines electroencephalogram (EEG) log subband power spectrum, correlation analysis, principal component analysis, and linear regression models to indirectly estimate driver's drowsiness level in a virtual-reality-based driving simulator. Our results demonstrated that it is feasible to accurately estimate quantitatively driving performance, expressed as deviation between the center of the vehicle and the center of the cruising lane, in a realistic driving simulator.

Transistorized PWM inverter-induction motor drive system

NASA Technical Reports Server (NTRS)

Peak, S. C.; Plunkett, A. B.

1982-01-01

This paper describes the development of a transistorized PWM inverter-induction motor traction drive system. A vehicle performance analysis was performed to establish the vehicle tractive effort-speed requirements. These requirements were then converted into a set of inverter and motor specifications. The inverter was a transistorized three-phase bridge using General Electric power Darlington transistors. The description of the design and development of this inverter is the principal object of this paper. The high-speed induction motor is a design which is optimized for use with an inverter power source. The primary feedback control is a torque angle control with voltage and torque outer loop controls. A current-controlled PWM technique is used to control the motor voltage. The drive has a constant torque output with PWM operation to base motor speed and a constant horsepower output with square wave operation to maximum speed. The drive system was dynamometer tested and the results are presented.

Optimal viscous damping of vibrating porous cylinders

NASA Astrophysics Data System (ADS)

Jafari Kang, Saeed; Masoud, Hassan

2017-11-01

We theoretically study small-amplitude oscillations of permeable cylinders immersed in an unbounded fluid. Specifically, we examine the effects of permeability and oscillation frequency on the damping coefficient, which is proportional to the power required to sustain the vibrations. Cylinders of both circular and non-circular cross-sections undergoing transverse and rotational vibrations are considered. Our calculations indicate that the damping coefficient often varies non-monotonically with the permeability. Depending on the oscillation period, the maximum damping of a permeable cylinder can be many times greater than that of an otherwise impermeable one. This might seem counter-intuitive at first since generally the power it takes to steadily drag a permeable object through the fluid is less than the power needed to drive the steady motion of the same but impermeable object. However, the driving power (or damping coefficient) for oscillating bodies is determined by not only the amplitude of the cyclic fluid force experienced by them but also by the phase shift between the force and their periodic motion. An increase in the latter is responsible for excess damping coefficient of vibrating porous cylinders.

Fault tolerant operation of switched reluctance machine

NASA Astrophysics Data System (ADS)

Wang, Wei

The energy crisis and environmental challenges have driven industry towards more energy efficient solutions. With nearly 60% of electricity consumed by various electric machines in industry sector, advancement in the efficiency of the electric drive system is of vital importance. Adjustable speed drive system (ASDS) provides excellent speed regulation and dynamic performance as well as dramatically improved system efficiency compared with conventional motors without electronics drives. Industry has witnessed tremendous grow in ASDS applications not only as a driving force but also as an electric auxiliary system for replacing bulky and low efficiency auxiliary hydraulic and mechanical systems. With the vast penetration of ASDS, its fault tolerant operation capability is more widely recognized as an important feature of drive performance especially for aerospace, automotive applications and other industrial drive applications demanding high reliability. The Switched Reluctance Machine (SRM), a low cost, highly reliable electric machine with fault tolerant operation capability, has drawn substantial attention in the past three decades. Nevertheless, SRM is not free of fault. Certain faults such as converter faults, sensor faults, winding shorts, eccentricity and position sensor faults are commonly shared among all ASDS. In this dissertation, a thorough understanding of various faults and their influence on transient and steady state performance of SRM is developed via simulation and experimental study, providing necessary knowledge for fault detection and post fault management. Lumped parameter models are established for fast real time simulation and drive control. Based on the behavior of the faults, a fault detection scheme is developed for the purpose of fast and reliable fault diagnosis. In order to improve the SRM power and torque capacity under faults, the maximum torque per ampere excitation are conceptualized and validated through theoretical analysis and experiments. With the proposed optimal waveform, torque production is greatly improved under the same Root Mean Square (RMS) current constraint. Additionally, position sensorless operation methods under phase faults are investigated to account for the combination of physical position sensor and phase winding faults. A comprehensive solution for position sensorless operation under single and multiple phases fault are proposed and validated through experiments. Continuous position sensorless operation with seamless transition between various numbers of phase fault is achieved.

International policies on alcohol impaired driving: are legal blood alcohol concentration (BAC) limits in motorized countries compatible with the scientific evidence?

PubMed

Desapriya, E B R; Iwase, Nobutada; Brussoni, Mariana; Shimizu, Shinji; Belayneh, Taye N

2003-04-01

Borkenstein et al. (1974) study indicated that drivers with BACs of 0.05 to 0.09 per cent were twice as likely to crash as drivers with a zero BAC. Drivers with BACs from 0.10 to 0.14 per cent were ten times as likely to have a fatal crash in 1964. There have been numerous efforts during the history of motorized countries to control the consumption of alcohol and the problems associated with it through legislative mandate, it was not until the 1970s that acceptance of legal BAC (Blood Alcohol Concentration) limits laws became widespread. In particular, as more and more people drive automobiles, the number of traffic accidents involving drunken drivers has soared, and many of these are known to be related to the consumption of alcohol. Thus, legislators find themselves under increasing pressure to find a reasonable and fair solution to the question of alcohol impaired driving, as the scientific evidence about alcohol consumption level and psycho motor functions impairment came to clear. A landmark event in the development of policies regarding impaired driving was the establishment of the fact that consumption of alcohol does, in fact, increase the probability of traffic crashes. Legal limit laws specify a maximum permissible BAC limit for drivers. Currently, a BAC laws range from zero tolerance and 0.02 to 0.10% constitutes prima facie evidence in most countries for 'Driving under Influence of Alcohol.' This latter standard is too permissive, as driving skills deteriorate and crash involvement risk increases beginning at 0.02%. There are consequences attached to setting a BAC limit so high that a 72 kg man can drink five bottles of beer and still be under legal limit. In this sense high legal BAC limit may influence people to make bad estimates of their relative risk of injury or death while driving. Provided there is adequate political will, millions of lives could be saved in the coming years. This review is an attempt to examine in detail the available information about legal BAC limit laws, and issue of considerable interest to both policy makers and the public.

Small passenger car transmission test-Chevrolet 200 transmission

NASA Technical Reports Server (NTRS)

Bujold, M. P.

1980-01-01

The small passenger car transmission was tested to supply electric vehicle manufacturers with technical information regarding the performance of commerically available transmissions which would enable them to design a more energy efficient vehicle. With this information the manufacturers could estimate vehicle driving range as well as speed and torque requirements for specific road load performance characteristics. A 1979 Chevrolet Model 200 automatic transmission was tested per a passenger car automatic transmission test code (SAE J651b) which required drive performance, coast performance, and no load test conditions. The transmission attained maximum efficiencies in the mid-eighty percent range for both drive performance tests and coast performance tests. Torque, speed and efficiency curves map the complete performance characteristics for Chevrolet Model 200 transmission.

A double B1-mode 4-layer laminated piezoelectric linear motor.

PubMed

Li, Xiaotian; Chen, Zhijiang; Dong, Shuxiang

2012-12-01

We report a miniature piezoelectric ultrasonic linear motor that is made of four Pb(Zr,Ti)O(3) (PZT) piezoelectric ceramic layers for low-voltage work. The 4-layer piezoelectric laminate works in two orthogonal first-bending modes for producing elliptical oscillations, which are then used to drive a contacting slider into continuous linear motion. Experimental results show that the miniature linear motor (size: 4 × 4 × 12 mm, weight: 1.7 g) can generate a large driving force of 0.48 N and a linear motion speed of up to 160 mm/s, using a 40 V(pp)/mm voltage drive at its resonance frequency of 64.5 kHz. The maximum efficiency of the linear motor is 30%.

33 CFR 183.33 - Maximum weight capacity: Inboard and inboard-outdrive boats.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (iv) Weight of full permanent fuel tanks. (3) “Machinery weight” is the combined weight of installed engines or motors, control equipment, drive units, and batteries. [CGD 72-61R, 37 FR 15782, Aug. 4, 1972...

Study on Pyroelectric Harvesters with Various Geometry

PubMed Central

Siao, An-Shen; Chao, Ching-Kong; Hsiao, Chun-Ching

2015-01-01

Pyroelectric harvesters convert time-dependent temperature variations into electric current. The appropriate geometry of the pyroelectric cells, coupled with the optimal period of temperature fluctuations, is key to driving the optimal load resistance, which enhances the performance of pyroelectric harvesters. The induced charge increases when the thickness of the pyroelectric cells decreases. Moreover, the induced charge is extremely reduced for the thinner pyroelectric cell when not used for the optimal period. The maximum harvested power is achieved when a 100 μm-thick PZT (Lead zirconate titanate) cell is used to drive the optimal load resistance of about 40 MΩ. Moreover, the harvested power is greatly reduced when the working resistance diverges even slightly from the optimal load resistance. The stored voltage generated from the 75 μm-thick PZT cell is less than that from the 400 μm-thick PZT cell for a period longer than 64 s. Although the thinner PZT cell is advantageous in that it enhances the efficiency of the pyroelectric harvester, the much thinner 75 μm-thick PZT cell and the divergence from the optimal period further diminish the performance of the pyroelectric cell. Therefore, the designers of pyroelectric harvesters need to consider the coupling effect between the geometry of the pyroelectric cells and the optimal period of temperature fluctuations to drive the optimal load resistance. PMID:26270666

Heating and current drive requirements towards steady state operation in ITER

NASA Astrophysics Data System (ADS)

Poli, F. M.; Bonoli, P. T.; Kessel, C. E.; Batchelor, D. B.; Gorelenkova, M.; Harvey, B.; Petrov, Y.

2014-02-01

Steady state scenarios envisaged for ITER aim at optimizing the bootstrap current, while maintaining sufficient confinement and stability to provide the necessary fusion yield. Non-inductive scenarios will need to operate with Internal Transport Barriers (ITBs) in order to reach adequate fusion gain at typical currents of 9 MA. However, the large pressure gradients associated with ITBs in regions of weak or negative magnetic shear can be conducive to ideal MHD instabilities, reducing the no-wall limit. The E × B flow shear from toroidal plasma rotation is expected to be low in ITER, with a major role in the ITB dynamics being played by magnetic geometry. Combinations of H/CD sources that maintain weakly reversed magnetic shear profiles throughout the discharge are the focus of this work. Time-dependent transport simulations indicate that, with a trade-off of the EC equatorial and upper launcher, the formation and sustainment of quasi-steady state ITBs could be demonstrated in ITER with the baseline heating configuration. However, with proper constraints from peeling-ballooning theory on the pedestal width and height, the fusion gain and the maximum non-inductive current are below the ITER target. Upgrades of the heating and current drive system in ITER, like the use of Lower Hybrid current drive, could overcome these limitations, sustaining higher non-inductive current and confinement, more expanded ITBs which are ideal MHD stable.

Heating and current drive requirements towards steady state operation in ITER

NASA Astrophysics Data System (ADS)

Poli, Francesca; Kessel, Charles; Bonoli, Paul; Batchelor, Donald; Harvey, Bob

2013-10-01

Steady state scenarios envisaged for ITER aim at optimizing the bootstrap current, while maintaining sufficient confinement and stability. Non-inductive scenarios will need to operate with Internal Transport Barriers (ITBs) to reach adequate fusion gain at typical currents of 9 MA. Scenarios are established as relaxed flattop states with time-dependent transport simulations with TSC. The E × B flow shear from toroidal plasma rotation is expected to be low in ITER, with a major role in the ITB dynamics being played by magnetic geometry. Combinations of external sources that maintain weakly reversed shear profiles and ρ (qmin >= 0 . 5 are the focus of this work. Simulations indicate that, with a trade-off of the EC equatorial and upper launcher, the formation and sustainment of ITBs could be demonstrated with the baseline configuration. However, with proper constraints from peeling-ballooning theory on the pedestal width and height, the fusion gain and the maximum non-inductive current (6.2MA) are below the target. Upgrades of the heating and current drive system, like the use of Lower Hybrid current drive, could overcome these limitations. With 30MW of coupled LH in the flattop and operating at the Greenwald density, plasmas can sustain ~ 9 MA and achieve Q ~ 4 . Work supported by the US Department of Energy under DE-AC02-CH0911466.

Deflection Analysis of the Space Shuttle External Tank Door Drive Mechanism

NASA Technical Reports Server (NTRS)

Tosto, Michael A.; Trieu, Bo C.; Evernden, Brent A.; Hope, Drew J.; Wong, Kenneth A.; Lindberg, Robert E.

2008-01-01

Upon observing an abnormal closure of the Space Shuttle s External Tank Doors (ETD), a dynamic model was created in MSC/ADAMS to conduct deflection analyses of the Door Drive Mechanism (DDM). For a similar analysis, the traditional approach would be to construct a full finite element model of the mechanism. The purpose of this paper is to describe an alternative approach that models the flexibility of the DDM using a lumped parameter approximation to capture the compliance of individual parts within the drive linkage. This approach allows for rapid construction of a dynamic model in a time-critical setting, while still retaining the appropriate equivalent stiffness of each linkage component. As a validation of these equivalent stiffnesses, finite element analysis (FEA) was used to iteratively update the model towards convergence. Following this analysis, deflections recovered from the dynamic model can be used to calculate stress and classify each component s deformation as either elastic or plastic. Based on the modeling assumptions used in this analysis and the maximum input forcing condition, two components in the DDM show a factor of safety less than or equal to 0.5. However, to accurately evaluate the induced stresses, additional mechanism rigging information would be necessary to characterize the input forcing conditions. This information would also allow for the classification of stresses as either elastic or plastic.

Proposal for massively parallel data storage system

NASA Technical Reports Server (NTRS)

Mansuripur, M.

1992-01-01

An architecture for integrating large numbers of data storage units (drives) to form a distributed mass storage system is proposed. The network of interconnected units consists of nodes and links. At each node there resides a controller board, a data storage unit and, possibly, a local/remote user-terminal. The links (twisted-pair wires, coax cables, or fiber-optic channels) provide the communications backbone of the network. There is no central controller for the system as a whole; all decisions regarding allocation of resources, routing of messages and data-blocks, creation and distribution of redundant data-blocks throughout the system (for protection against possible failures), frequency of backup operations, etc., are made locally at individual nodes. The system can handle as many user-terminals as there are nodes in the network. Various users compete for resources by sending their requests to the local controller-board and receiving allocations of time and storage space. In principle, each user can have access to the entire system, and all drives can be running in parallel to service the requests for one or more users. The system is expandable up to a maximum number of nodes, determined by the number of routing-buffers built into the controller boards. Additional drives, controller-boards, user-terminals, and links can be simply plugged into an existing system in order to expand its capacity.

Assessment of driving capability through the use of clinical and psychomotor tests in relation to blood cannabinoids levels following oral administration of 20 mg dronabinol or of a cannabis decoction made with 20 or 60 mg Delta9-THC.

PubMed

Ménétrey, Annick; Augsburger, Marc; Favrat, Bernard; Pin, Marie A; Rothuizen, Laura E; Appenzeller, Monique; Buclin, Thierry; Mangin, Patrice; Giroud, Christian

2005-01-01

Delta(9)-Tetrahydrocannabinol (THC) is frequently found in the blood of drivers suspected of driving under the influence of cannabis or involved in traffic crashes. The present study used a double-blind crossover design to compare the effects of medium (16.5 mg THC) and high doses (45.7 mg THC) of hemp milk decoctions or of a medium dose of dronabinol (20 mg synthetic THC, Marinol on several skills required for safe driving. Forensic interpretation of cannabinoids blood concentrations were attempted using the models proposed by Daldrup (cannabis influencing factor or CIF) and Huestis and coworkers. First, the time concentration-profiles of THC, 11-hydroxy-Delta(9)-tetrahydrocannabinol (11-OH-THC) (active metabolite of THC), and 11-nor-9-carboxy-Delta(9)-tetrahydrocannabinol (THCCOOH) in whole blood were determined by gas chromatography-mass spectrometry-negative ion chemical ionization. Compared to smoking studies, relatively low concentrations were measured in blood. The highest mean THC concentration (8.4 ng/mL) was achieved 1 h after ingestion of the strongest decoction. Mean maximum 11-OH-THC level (12.3 ng/mL) slightly exceeded that of THC. THCCOOH reached its highest mean concentration (66.2 ng/mL) 2.5-5.5 h after intake. Individual blood levels showed considerable intersubject variability. The willingness to drive was influenced by the importance of the requested task. Under significant cannabinoids influence, the participants refused to drive when they were asked whether they would agree to accomplish several unimportant tasks, (e.g., driving a friend to a party). Most of the participants reported a significant feeling of intoxication and did not appreciate the effects, notably those felt after drinking the strongest decoction. Road sign and tracking testing revealed obvious and statistically significant differences between placebo and treatments. A marked impairment was detected after ingestion of the strongest decoction. A CIF value, which relies on the molar ratio of main active to inactive cannabinoids, greater than 10 was found to correlate with a strong feeling of intoxication. It also matched with a significant decrease in the willingness to drive, and it matched also with a significant impairment in tracking performances. The mathematic model II proposed by Huestis et al. (1992) provided at best a rough estimate of the time of oral administration with 27% of actual values being out of range of the 95% confidence interval. The sum of THC and 11-OH-THC blood concentrations provided a better estimate of impairment than THC alone. This controlled clinical study points out the negative influence on fitness to drive after medium or high dose oral THC or dronabinol.

Baseline tests of the battronic Minivan electric delivery van

NASA Technical Reports Server (NTRS)

Dustin, M. O.; Soltis, R. F.; Bozek, J. M.; Maslowski, E. A.

1977-01-01

An electric passenger vehicle was tested to develop data characterizing the state of the art of electric and hybrid vehicles. The test measured vehicle maximum speed, range at constant speed, range over stop-and-go driving schedules, maximum acceleration, gradeability and limit, road energy consumption, road power, indicated energy consumption, braking capability and battery charge efficiency. The data obtained are to serve as a baseline to compare improvements in electric and hybrid vehicle technologies and to assist in establishing performance standards.

Baseline tests of the EPC Hummingbird electric passenger vehicle

NASA Technical Reports Server (NTRS)

Slavik, R. J.; Maslowski, E. A.; Sargent, N. B.; Birchenough, A. G.

1977-01-01

The rear-mounted internal combustion engine in a four-passenger Volkswagen Thing was replaced with an electric motor made by modifying an aircraft generator and powered by 12 heavy-duty, lead-acid battery modules. Vehicle performance tests were conducted to measure vehicle maximum speed, range at constant speed, range over stop-and-go driving schedules, maximum acceleration, gradeability limit, road energy consumption, road power, indicated energy consumption, braking capability, battery charger efficiency, and battery characteristics. Test results are presented in tables and charts.

Predictive validity of driving-simulator assessments following traumatic brain injury: a preliminary study.

PubMed

Lew, Henry L; Poole, John H; Lee, Eun Ha; Jaffe, David L; Huang, Hsiu-Chen; Brodd, Edward

2005-03-01

To evaluate whether driving simulator and road test evaluations can predict long-term driving performance, we conducted a prospective study on 11 patients with moderate to severe traumatic brain injury. Sixteen healthy subjects were also tested to provide normative values on the simulator at baseline. At their initial evaluation (time-1), subjects' driving skills were measured during a 30-minute simulator trial using an automated 12-measure Simulator Performance Index (SPI), while a trained observer also rated their performance using a Driving Performance Inventory (DPI). In addition, patients were evaluated on the road by a certified driving evaluator. Ten months later (time-2), family members observed patients driving for at least 3 hours over 4 weeks and rated their driving performance using the DPI. At time-1, patients were significantly impaired on automated SPI measures of driving skill, including: speed and steering control, accidents, and vigilance to a divided-attention task. These simulator indices significantly predicted the following aspects of observed driving performance at time-2: handling of automobile controls, regulation of vehicle speed and direction, higher-order judgment and self-control, as well as a trend-level association with car accidents. Automated measures of simulator skill (SPI) were more sensitive and accurate than observational measures of simulator skill (DPI) in predicting actual driving performance. To our surprise, the road test results at time-1 showed no significant relation to driving performance at time-2. Simulator-based assessment of patients with brain injuries can provide ecologically valid measures that, in some cases, may be more sensitive than a traditional road test as predictors of long-term driving performance in the community.

Progressive Return to Activity Following Acute Concussion/Mild Traumatic Brain Injury: Guidance for the Rehabilitation Provider in Deployed and Non-deployed Settings

DTIC Science & Technology

2014-01-01

activity requires minimum 2 hours of rest • Video games , driving simulation ― 20 minutes to maximum of 40 minutes, followed by 80 minutes cognitive...as breath-holding, exertion, playing video games and driving. He is encouraged to monitor his HR before and during activity (not to exceed 40 percent...walking at low speed b) Shopping in the exchange for a single item c) Video games d) Television with rest breaks each hour Knowledge Test

Performance testing of EVs in the EPRI/TVA EV program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Driggans, R.L.

1983-01-01

Performance testing has been completed on four electric vehicles: the Grumman-Olson Kubvan, SCT Electric (VW) Pickup, Jet Industries Electrica, and VW Electrotransporter Bus. The tests performed included vehicle dc energy consumption and driving range at constant speeds and on the SAE J227a C cycle, on-road driving range, hill climbing, maximum acceleration, top speed, and braking performance. Descriptions of the vehicles tested and comparisons of major performance parameters on all four vehicles are presented. This testing was performed at the TVA Electric Vehicle Test Facility.

Driving time modulates accommodative response and intraocular pressure.

PubMed

Vera, Jesús; Diaz-Piedra, Carolina; Jiménez, Raimundo; Morales, José M; Catena, Andrés; Cardenas, David; Di Stasi, Leandro L

2016-10-01

Driving is a task mainly reliant on the visual system. Most of the time, while driving, our eyes are constantly focusing and refocusing between the road and the dashboard or near and far traffic. Thus, prolonged driving time should produce visual fatigue. Here, for the first time, we investigated the effects of driving time, a common inducer of driver fatigue, on two ocular parameters: the accommodative response (AR) and the intraocular pressure (IOP). A pre/post-test design has been used to assess the impact of driving time on both indices. Twelve participants (out of 17 recruited) completed the study (5 women, 24.42±2.84years old). The participants were healthy and active drivers with no visual impairment or pathology. They drove for 2h in a virtual driving environment. We assessed AR and IOP before and after the driving session, and also collected subjective measures of arousal and fatigue. We found that IOP and AR decreased (i.e., the accommodative lag increased) after the driving session (p=0.03 and p<0.001, respectively). Moreover, the nearest distances tested (20cm, 25cm, and 33cm) induced the highest decreases in AR (corrected p-values<0.05). Consistent with these findings, the subjective levels of arousal decreased and levels of fatigue increased after the driving session (all p-values<0.001). These results represent an innovative step towards an objective, valid, and reliable assessment of fatigue-impaired driving based on visual fatigue signs. Copyright © 2016 Elsevier Inc. All rights reserved.

On Quasi-biennial Oscillations in Chromospheric Macrospicules and Their Potential Relation to the Global Solar Magnetic Field

NASA Astrophysics Data System (ADS)

Kiss, T. S.; Erdélyi, R.

2018-04-01

This study aims to provide further evidence for the potential influence of the global solar magnetic field on localized chromospheric jets, the macrospicules (MS). To find a connection between the long-term variation of properties of MS and other solar activity proxies, including, e.g., the temporal variation of the frequency shift of solar global oscillations, sunspot area, etc., a database overarching seven years of observations was compiled. This database contains 362 MS, based on observations at the 30.4 nm of the Atmospheric Imaging Assembly on board the Solar Dynamics Observatory. Three of the five investigated physical properties of MS show a clear long-term temporal variation after smoothing the raw data. Wavelet analysis of the temporal variation of maximum length, maximum area, and average velocity is carried out. The results reveal a strong pattern of periodicities at around 2 years (also referred to as quasi-biennial oscillations—QBOs). A comparison with solar activity proxies that also possess the properties of QBOs provides some interesting features: the minima and maxima of QBOs of MS properties occur at around the same epoch as the minima and maxima of these activity proxies. For most of the time span investigated, the oscillations are out of phase. This out-of-phase behavior was also corroborated by a cross-correlation analysis. These results suggest that the physical processes that generate and drive the long-term evolution of the global solar activity proxies may be coupled to the short-term local physical processes driving the macrospicules, and, therefore modulate the properties of local dynamics.

Fast Transport of Water Droplets over a Thermo-Switchable Surface Using Rewritable Wettability Gradient.

PubMed

Banuprasad, Theneyur Narayanaswamy; Vinay, Thamarasseril Vijayan; Subash, Cherumannil Karumuthil; Varghese, Soney; George, Sajan D; Varanakkottu, Subramanyan Namboodiri

2017-08-23

In spite of the reported temperature dependent tunability in wettability of poly(N-isopropylacrylamide) (PNIPAAm) surfaces for below and above lower critical solution temperature (32 °C), the transport of water droplets is inhibited by the large contact angle hysteresis. Herein, for the first time, we report on-demand, fast, and reconfigurable droplet manipulation over a PNIPAAm grafted structured polymer surface using temperature-induced wettability gradient. Our study reveals that the PNIPAAm grafted on intrinsically superhydrophobic surfaces exhibit hydrophilic nature with high contact angle hysteresis below 30 °C and superhydrophobic nature with ultralow contact angle hysteresis above 36 °C. The transition region between 30 and 36 °C is characterized by a large change in water contact angle (∼100°) with a concomitant change in contact angle hysteresis. By utilizing this "transport zone" wherein driving forces overcome the frictional forces, we demonstrate macroscopic transport of water drops with a maximum transport velocity of approximately 40 cm/s. The theoretical calculations on the force measurements concur with dominating behavior of driving forces across the transport zone. The tunability in transport velocity by varying the temperature gradient along the surface or the inclination angle of the surface (maximum angle of 15° with a reduced velocity 0.4 mm/s) is also elucidated. In addition, as a practical application, coalescence of water droplets is demonstrated by using the temperature controlled wettability gradient. The presented results are expected to provide new insights on the design and fabrication of smart multifunctional surfaces for applications such as biochemical analysis, self-cleaning, and microfluidics.

Studies on the positive inotropic effect of phenylephrine: a comparison with isoprenaline.

PubMed

Ledda, F; Marchetti, P; Mugelli, A

1975-05-01

1. The effects of phenylephrine and isoprenaline on the isometric contraction of guinea-pig ventricle were compared over the whole range of their respective dose-response curves. 2. In preparations driven at 2.5 Hz the increase in contractile force induced by either isoprenaline of phenylephrine was linearly correlated to an increase in maximum velocity of force development. The relaxation time was shortened by isoprenaline but not by phenylephrine. 3. The negative inotropic effect induced by delta [N-(3,4-dimethoxyphenethyl)-N-methyl-amino]-alpha-(3,4,5-trimethoxyphenyl)alpha-isopropylvaleronitrile hydrochloride (D(600)) was reversed by isoprenaline, but little influenced by phenylephrine. 4. The study of the interval-force relationship shows that the increase in contractile force induced by phenylephrine (3 X 10(-5) M) was relatively greater at low frequencies of stimulation, and that the maximum effect was reached at the frequency of 1 Hz. 5. The positive inotropic effect of phenylephrine (10-4 M) was significantly higher at a frequency of 1 Hz than at 2.5 Hz; the effect of isoprenaline (3 x 10-8 M) was not significantly different at the two driving frequencies. 6. In preparations driven at 1 Hz the inotropic effect of the lower concentrations of phenylephrine was due to an increase in the time to peak tension without any change of the maximum velocity of force development; however an increase of this parameter became evident only after higher concentrations of the amine (10-5 M or more), associated with a progressive shortening of the time to peak. 7. A correlation between mechanical and electrophysiological effects of phenylephrine is attempted; the suggestion is advanced that the prolongation of the action potential and of the active state duration may be an important factor in the inotropic effect of phenylephrine.

30 CFR 56.10008 - Riding tramways.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Riding tramways. Persons other than maintenance persons shall not ride aerial tramways unless the following features are provided: (a) Two independent brakes, each capable of holding the maximum load; (b) Direct communication between terminals; (c) Power drives with emergency power available in case of...

30 CFR 57.10008 - Riding tramways.

Code of Federal Regulations, 2010 CFR

2010-07-01

....10008 Riding tramways. Persons other than maintenance persons shall not ride aerial tramways unless the following features are provided. (a) Two independent brakes, each capable of holding the maximum load; (b) Direct communication between terminals; (c) Power drives with emergency power available in case of...

600-602 N Lakeshore Drive, March 2011, Lindsay Light Radiological Survey

EPA Pesticide Factsheets

The fieldgamma measurements within the excavation and the spoil materials generated during the excavationprocess did not exceed the respective threshold values previously stated and ranged from a minimum of4,382 cpm to a maximum of 7,907 cpm.

Design Alternatives to Improve Access Time Performance of Disk Drives Under DOS and UNIX

NASA Astrophysics Data System (ADS)

Hospodor, Andy

For the past 25 years, improvements in CPU performance have overshadowed improvements in the access time performance of disk drives. CPU performance has been slanted towards greater instruction execution rates, measured in millions of instructions per second (MIPS). However, the slant for performance of disk storage has been towards capacity and corresponding increased storage densities. The IBM PC, introduced in 1982, processed only a fraction of a MIP. Follow-on CPUs, such as the 80486 and 80586, sported 5-10 MIPS by 1992. Single user PCs and workstations, with one CPU and one disk drive, became the dominant application, as implied by their production volumes. However, disk drives did not enjoy a corresponding improvement in access time performance, although the potential still exists. The time to access a disk drive improves (decreases) in two ways: by altering the mechanical properties of the drive or by adding cache to the drive. This paper explores the improvement to access time performance of disk drives using cache, prefetch, faster rotation rates, and faster seek acceleration.

PIC simulations of post-pulse field reversal and secondary ionization in nanosecond argon discharges

NASA Astrophysics Data System (ADS)

Kim, H. Y.; Gołkowski, M.; Gołkowski, C.; Stoltz, P.; Cohen, M. B.; Walker, M.

2018-05-01

Post-pulse electric field reversal and secondary ionization are investigated with a full kinetic treatment in argon discharges between planar electrodes on nanosecond time scales. The secondary ionization, which occurs at the falling edge of the voltage pulse, is induced by charge separation in the bulk plasma region. This process is driven by a reverse in the electric field from the cathode sheath to the formerly driven anode. Under the influence of the reverse electric field, electrons in the bulk plasma and sheath regions are accelerated toward the cathode. The electron movement manifests itself as a strong electron current generating high electron energies with significant electron dissipated power. Accelerated electrons collide with Ar molecules and an increased ionization rate is achieved even though the driving voltage is no longer applied. With this secondary ionization, in a single pulse (SP), the maximum electron density achieved is 1.5 times higher and takes a shorter time to reach using 1 kV 2 ns pulse as compared to a 1 kV direct current voltage at 1 Torr. A bipolar dual pulse excitation can increase maximum density another 50%–70% above a SP excitation and in half the time of RF sinusoidal excitation of the same period. The first field reversal is most prominent but subsequent field reversals also occur and correspond to electron temperature increases. Targeted pulse designs can be used to condition plasma density as required for fast discharge applications.

Secondary Behavior of Drivers on Cell Phones.

PubMed

Farmer, Charles M; Klauer, Sheila G; McClafferty, Julie A; Guo, Feng

2015-01-01

The objective of this study was to determine whether cell phone use by drivers leads to changes in the frequency of other types of potentially distracting behavior. There were 2 main questions of interest: (1) As each driver changes cell phone use, does he or she change the amount of driving time spent on other distracting behavior? (2) As each driver changes cell phone use, does he or she change the amount of driving time spent looking away from the driving task? Day-to-day driving behavior of 105 volunteer subjects was monitored over a period of 1 year. The amount of driving time during each trip spent on tasks secondary to driving (or looking away from the driving task) was correlated to the amount of time on a cell phone, taking into account the relationships among trips taken by the same driver. Drivers spent 42% of the time engaging in at least one secondary activity. Drivers were talking on a cell phone 7% of the time, interacting in some other way with a cell phone 5% of the time, and engaging in some other secondary activity (sometimes in conjunction with cell phone use) 33% of the time. Other than cell phone use, the most common secondary activities were interacting with a passenger (12% of driving time), holding but not otherwise interacting with an object (6%), and talking/singing/dancing to oneself (5%). Drivers were looking straight forward 81% of the time, forward left or right 5% of time, in a mirror 4% of the time, and elsewhere (eyes off driving task) 10% of time. On average, for each 1 percentage point increase in cell phone talking, the other secondary behavior rate decreased by 0.28 percentage points (P <.0001), and the rate of eyes off driving task decreased by 0.02 percentage points (P =.0067). For each 1 percentage point increase in the amount of other cell phone interaction per trip, the other secondary behavior rate decreased by 0.08 percentage points (P =.0558), but the rate of eyes off driving task increased by 0.06 percentage points (P <.0001). Although using a cell phone can be distracting from the driving task, other secondary activities can be equally or more distracting, at least as measured by eye glances away from the road ahead and mirrors. In this group of drivers, dialing, reaching for, and answering the cell phone were associated with increased eyes off driving task, as opposed to the decrease in eyes off driving task associated with talking on the phone. Predictions about the effect of cell phone usage on driver distraction need to consider what other behavior is being displaced by the time spent on the phone. A focus by researchers, policy-makers, and the media on the distraction of using cell phones while driving may lead drivers to disregard the risk of other secondary behavior that is even more distracting.

A simple phenomenological model for grain clustering in turbulence

NASA Astrophysics Data System (ADS)

Hopkins, Philip F.

2016-01-01

We propose a simple model for density fluctuations of aerodynamic grains, embedded in a turbulent, gravitating gas disc. The model combines a calculation for the behaviour of a group of grains encountering a single turbulent eddy, with a hierarchical approximation of the eddy statistics. This makes analytic predictions for a range of quantities including: distributions of grain densities, power spectra and correlation functions of fluctuations, and maximum grain densities reached. We predict how these scale as a function of grain drag time ts, spatial scale, grain-to-gas mass ratio tilde{ρ }, strength of turbulence α, and detailed disc properties. We test these against numerical simulations with various turbulence-driving mechanisms. The simulations agree well with the predictions, spanning ts Ω ˜ 10-4-10, tilde{ρ }˜ 0{-}3, α ˜ 10-10-10-2. Results from `turbulent concentration' simulations and laboratory experiments are also predicted as a special case. Vortices on a wide range of scales disperse and concentrate grains hierarchically. For small grains this is most efficient in eddies with turnover time comparable to the stopping time, but fluctuations are also damped by local gas-grain drift. For large grains, shear and gravity lead to a much broader range of eddy scales driving fluctuations, with most power on the largest scales. The grain density distribution has a log-Poisson shape, with fluctuations for large grains up to factors ≳1000. We provide simple analytic expressions for the predictions, and discuss implications for planetesimal formation, grain growth, and the structure of turbulence.

Driver fatigue and highway driving: a simulator study.

PubMed

Ting, Ping-Huang; Hwang, Jiun-Ren; Doong, Ji-Liang; Jeng, Ming-Chang

2008-06-09

Long duration of driving is a significant cause of fatigue-related accidents on motorways or major roadways. The fatigue caused by driving for extended periods acutely impairs driver alertness and performance and can compromise transportation safety. This study quantitatively measured the progression of driver fatigue and identified the conservative safe duration of continuous highway driving. Thirty young male subjects were analyzed during 90 min of laboratory-simulated highway driving. Sleepiness ratings (SSS) and reaction time (RT) tests were used to assess impairment of driver alertness and vigilance. Additionally, various measures of driving performance recorded throughout the experiment were used to measure temporal deterioration of driver performance from alert to fatigued using principal component analysis (PCA). The analytical results revealed that SSS scores, reaction times (RTs) and unstable driving performance significantly increased over time, indicating that excessive driving time is a significant fatigue factor and potential cause of fatigue-related accidents. Moreover, the analytical results indicated that 80 min was the safe limit for monotonous highway driving. Based on the experimental findings of this study, public awareness of the adverse affects of driver fatigue during long-distance driving should be enhanced. This study provides explicit information of fatigue development that can be used to prevent fatigue-related accidents.

Effect of spine motion on mobility in quadruped running

NASA Astrophysics Data System (ADS)

Chen, Dongliang; Liu, Qi; Dong, Litao; Wang, Hong; Zhang, Qun

2014-11-01

Most of current running quadruped robots have similar construction: a stiff body and four compliant legs. Many researches have indicated that the stiff body without spine motion is a main factor in limitation of robots' mobility. Therefore, investigating spine motion is very important to build robots with better mobility. A planar quadruped robot is designed based on cheetahs' morphology. There is a spinal driving joint in the body of the robot. When the spinal driving joint acts, the robot has spine motion; otherwise, the robot has not spine motion. Six group prototype experiments with the robot are carried out to study the effect of spine motion on mobility. In each group, there are two comparative experiments: the spinal driving joint acts in one experiment but does not in the other experiment. The results of the prototype experiments indicate that the average speeds of the robot with spine motion are 8.7%-15.9% larger than those of the robot without spine motion. Furthermore, a simplified sagittal plane model of quadruped mammals is introduced. The simplified model also has a spinal driving joint. Using a similar process as the prototype experiments, six group simulation experiments with the simplified model are conducted. The results of the simulation experiments show that the maximum rear leg horizontal thrusts of the simplified mode with spine motion are 68.2%-71.3% larger than those of the simplified mode without spine motion. Hence, it is found that spine motion can increase the average running speed and the intrinsic reason of speed increase is the improvement of the maximum rear leg horizontal thrust.

Comparison of modified driver circuit and capacitor-transfer circuit in longitudinally excited N2 laser.

PubMed

Uno, Kazuyuki; Akitsu, Tetsuya; Nakamura, Kenshi; Jitsuno, Takahisa

2013-04-01

We developed a modified driver circuit composed of a capacitance and a spark gap, called a direct-drive circuit, for a longitudinally excited gas laser. The direct-drive circuit uses a large discharge impedance caused by a long discharge length of the longitudinal excitation scheme and eliminates the buffer capacitance used in the traditional capacitor-transfer circuit. We compared the direct-drive circuit and the capacitor-transfer circuit in a longitudinally excited N2 laser (wavelength: 337 nm). Producing high output energy with the capacitor-transfer circuit requires a large storage capacitance and a discharge tube with optimum dimensions (an inner diameter of 4 mm and a length of 10 cm in this work); in contrast, the direct-drive circuit requires a high breakdown voltage, achieved with a small storage capacitance and a large discharge tube. Additionally, for the same input energy of 792 mJ, the maximum output energy of the capacitor-transfer circuit was 174.2 μJ, and that of the direct-drive circuit was 344.7 μJ.

Development of a bi-directional standing wave linear piezoelectric actuator with four driving feet.

PubMed

Liu, Yingxiang; Shi, Shengjun; Li, Chunhong; Chen, Weishan; Wang, Liang; Liu, Junkao

2018-03-01

A bi-directional standing wave linear piezoelectric ultrasonic actuator with four driving feet is proposed in this work. Two sandwich type transducers operated in longitudinal-bending hybrid modes are set parallelly. The working mode of the transducer is not simple hybrid vibrations of a longitudinal one and a bending one, but a special coupling vibration mode contained both longitudinal and bending components. Two transducers with the same structure and unsymmetrical boundary conditions are set parallelly to accomplish the bi-directional driving: the first transducer can push the runner forward, while the other one produces the backward driving. In the experiments, two voltages with different amplitudes are applied on the two transducers, respectively: the one with higher voltage serves as the actuator, whereas the other one applied with lower voltage is used to reduce the frictional force. The prototype achieves maximum no-load speed and thrust force of 244 mm/s and 9.8 N. This work gives a new idea for the construction of standing wave piezoelectric ultrasonic actuator with bi-directional driving ability. Copyright © 2017 Elsevier B.V. All rights reserved.

Continued driving and time to transition to nondriver status through error-specific driving restrictions.

PubMed

Freund, Barbara; Petrakos, Davithoula

2008-01-01

We developed driving restrictions that are linked to specific driving errors, allowing cognitively impaired individuals to continue to independently meet mobility needs while minimizing risk to themselves and others. The purpose of this project was to evaluate the efficacy and duration expectancy of these restrictions in promoting safe continued driving. We followed 47 drivers age 60 years and older for 18 months, evaluating driving performance at 6-month intervals. Results demonstrated restricted drivers had safety profiles similar to safe drivers and gained additional driving time to transition to nondrivers.

[The spectrogram characteristics of organic blue-emissive light-emitting excitated YAG : Ce phosphor].

PubMed

Xi, Jian-Fei; Zhang, Fang-Hui; Mu, Qiang; Zhang, Mai-Li

2011-09-01

It is demonstrated that the panchromatic luminescence devices with organic blue-emissive light-emitting was fabricated. This technique used down conversion, which was already popular in inorganic power LEDs to obtain white light emission. A blue OLED device with a configuration of ITO/2T-NATA (30 nm)/AND : TBPe (50 Wt%, 40 nm)/Alq3 (100 nm)/LiF(1 nm)/Al(100 nm) was prepared via vacuum deposition process, and then coated with YAG : Ce phosphor layers of different thicknesses to obtain a controllable and uniform shape while the CIE coordinates were fine tuned. This development not only decreased steps of technics and degree of difficulty, but also applied the mature technology of phosphor. The results showed that steady spectrogram was obtained in the devices with phosphor, with a best performance of a maximum luminance of 13 840 cd x m(-2) which was about 2 times of that of the devices without phosphor; a maximum current efficiency of 17.3 cd x A(-1) was increased more two times more than the devices without phosphor. The emission spectrum could be adjusted by varying the concentration and thickness of the phosphor layers. Absoulte spectrogram of devices was in direct proportion with different driving current corresponding.

Optical and ultraviolet spectroscopic analysis of SN 2011fe at late times

NASA Astrophysics Data System (ADS)

Friesen, Brian; Baron, E.; Parrent, Jerod T.; Thomas, R. C.; Branch, David; Nugent, Peter E.; Hauschildt, Peter H.; Foley, Ryan J.; Wright, Darryl E.; Pan, Yen-Chen; Filippenko, Alexei V.; Clubb, Kelsey I.; Silverman, Jeffrey M.; Maeda, Keiichi; Shivvers, Isaac; Kelly, Patrick L.; Cohen, Daniel P.; Rest, Armin; Kasen, Daniel

2017-05-01

We present optical spectra of the nearby Type Ia supernova SN 2011fe at 100, 205, 311, 349 and 578 d post-maximum light, as well as an ultraviolet (UV) spectrum obtained with the Hubble Space Telescope at 360 d post-maximum light. We compare these observations with synthetic spectra produced with the radiative transfer code phoenix. The day +100 spectrum can be well fitted with models that neglect collisional and radiative data for forbidden lines. Curiously, including these data and recomputing the fit yields a quite similar spectrum, but with different combinations of lines forming some of the stronger features. At day +205 and later epochs, forbidden lines dominate much of the optical spectrum formation; however, our results indicate that recombination, not collisional excitation, is the most influential physical process driving spectrum formation at these late times. Consequently, our synthetic optical and UV spectra at all epochs presented here are formed almost exclusively through recombination-driven fluorescence. Furthermore, our models suggest that the UV spectrum even as late as day +360 is optically thick and consists of permitted lines from several iron-peak species. These results indicate that the transition to the 'nebular' phase in Type Ia supernovae is complex and highly wavelength dependent.

Optical and ultraviolet spectroscopic analysis of SN 2011fe at late times

DOE PAGES

Friesen, Brian; Baron, E.; Parrent, Jerod T.; ...

2017-02-27

This paper presents optical spectra of the nearby Type Ia supernova SN 2011fe at 100, 205, 311, 349 and 578 d post-maximum light, as well as an ultraviolet (UV) spectrum obtained with the Hubble Space Telescope at 360 d post-maximum light. We compare these observations with synthetic spectra produced with the radiative transfer code PHOENIX. The day +100 spectrum can be well fitted with models that neglect collisional and radiative data for forbidden lines. Curiously, including these data and recomputing the fit yields a quite similar spectrum, but with different combinations of lines forming some of the stronger features. Atmore » day +205 and later epochs, forbidden lines dominate much of the optical spectrum formation; however, our results indicate that recombination, not collisional excitation, is the most influential physical process driving spectrum formation at these late times. Consequently, our synthetic optical and UV spectra at all epochs presented here are formed almost exclusively through recombinationdriven fluorescence. Furthermore, our models suggest that the UV spectrum even as late as day +360 is optically thick and consists of permitted lines from several iron-peak species. These results indicate that the transition to the 'nebular' phase in Type Ia supernovae is complex and highly wavelength dependent.« less

Design and Analysis of an Electromagnetic Thrust Bearing

NASA Technical Reports Server (NTRS)

Banerjee, Bibhuti; Rao, Dantam K.

1996-01-01

A double-acting electromagnetic thrust bearing is normally used to counter the axial loads in many rotating machines that employ magnetic bearings. It essentially consists of an actuator and drive electronics. Existing thrust bearing design programs are based on several assumptions. These assumptions, however, are often violated in practice. For example, no distinction is made between maximum external loads and maximum bearing forces, which are assumed to be identical. Furthermore, it is assumed that the maximum flux density in the air gap occurs at the nominal gap position of the thrust runner. The purpose of this paper is to present a clear theoretical basis for the design of the electromagnetic thrust bearing which obviates such assumptions.

Designing feedback to mitigate teen distracted driving: A social norms approach.

PubMed

Merrikhpour, Maryam; Donmez, Birsen

2017-07-01

The purpose of this research is to investigate teens' perceived social norms and whether providing normative information can reduce distracted driving behaviors among them. Parents are among the most important social referents for teens; they have significant influences on teens' driving behaviors, including distracted driving which significantly contributes to teens' crash risks. Social norms interventions have been successfully applied in various domains including driving; however, this approach is yet to be explored for mitigating driver distraction among teens. Forty teens completed a driving simulator experiment while performing a self-paced visual-manual secondary task in four between-subject conditions: a) social norms feedback that provided a report at the end of each drive on teens' distracted driving behavior, comparing their distraction engagement to their parent's, b) post-drive feedback that provided just the report on teens' distracted driving behavior without information on their parents, c) real-time feedback in the form of auditory warnings based on eyes of road-time, and d) no feedback as control. Questionnaires were administered to collect data on these teens' and their parents' self-reported engagement in driver distractions and the associated social norms. Social norms and real-time feedback conditions resulted in significantly smaller average off-road glance duration, rate of long (>2s) off-road glances, and standard deviation of lane position compared to no feedback. Further, social norms feedback decreased brake response time and percentage of time not looking at the road compared to no feedback. No major effect was observed for post-drive feedback. Questionnaire results suggest that teens appeared to overestimate parental norms, but no effect of feedback was found on their perceptions. Feedback systems that leverage social norms can help mitigate driver distraction among teens. Overall, both social norms and real-time feedback induced positive driving behaviors, with social norms feedback outperforming real-time feedback. Copyright © 2017 Elsevier Ltd. All rights reserved.

Glider kits cut truck costs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1984-02-01

Trucks used for the delivery of coal have a relatively limited life because they must be specified for somewhat less than brute strength in order to achieve maximum payload within existing weight and length limitations. The major drive train components such as engine, transmission, and drive axles can last longer if rebuilt or remanufactured periodically. For that reason glider kits and other truck components ready for the installation of the drive chain are becoming increasingly popular. These kits have been available for many years, but were regarded only as a means of salvaging late model wrecks or burned trucks. Theirmore » recent acceptance as a means of periodic fleet updating is built around the low cost and immediate availability of remanufactured major components. The cost advantages in using these glider kits are discussed.« less

Study of the choice of the decoupling layout for the ITER ICRH system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vervier, M., E-mail: michel.vervier@rma.ac.be; Messiaen, A.; Ongena, J.

10 decouplers are used to neutralize the mutual coupling effects and to control the current amplitude of the 24 straps array of the ITER ICRH antenna in the case of current drive phasing. In the case of heating phasing only 4 decouplers are active and the array current control needs to act on the ratio between the power delivered by the 4 generators. This ratio is very sensitive to the precise adjustment of the antenna array phasing. The maximum total radiated power capability is then limited when the power of one generator reaches its maximum value. With the addition ofmore » four switches all 10 installed decouplers are made active and can act on all mutual coupling effects with equal source power from the 4 generators. With four more switches the current drive phasing could work with a reduced poloidal phasing resulting in a 35% increase of its coupling to the plasma.« less

A thermo-mechanical correlation with driving forces for hcp martensite and twin formations in the Fe-Mn-C system exhibiting multicomposition sets.

PubMed

Nakano, Jinichiro

2013-02-01

The thermodynamic properties of the Fe-Mn-C system were investigated by using an analytical model constructed by a CALPHAD approach. The stacking fault energy (SFE) of the fcc structure with respect to the hcp phase was always constant at T 0 , independent of the composition and temperature when other related parameters were assumed to be constant. Experimental limits for the thermal hcp formation and the mechanical (deformation-induced) hcp formation were separated by the SFE at T 0 . The driving force for the fcc to hcp transition, defined as a dimensionless value -d G m /( RT ), was determined in the presence of Fe-rich and Mn-rich composition sets in each phase. Carbon tended to partition to the Mn-rich phase rather than to the Fe-rich phase for the compositions studied. The results obtained revealed a thermo-mechanical correlation with empirical yield strength, maximum true stress and maximum true strain. The proportionality between thermodynamics and mechanical properties is discussed.

Nonlinear focal shift beyond the geometrical focus in moderately focused acoustic beams.

PubMed

Camarena, Francisco; Adrián-Martínez, Silvia; Jiménez, Noé; Sánchez-Morcillo, Víctor

2013-08-01

The phenomenon of the displacement of the position along the axis of the pressure, intensity, and radiation force maxima of focused acoustic beams under increasing driving voltages (nonlinear focal shift) is studied for the case of a moderately focused beam. The theoretical and experimental results show the existence of this shift along the axis when the initial pressure in the transducer increases until the acoustic field reaches the fully developed nonlinear regime of propagation. Experimental data show that at high amplitudes and for moderate focusing, the position of the on-axis pressure maximum and radiation force maximum can surpass the geometrical focal length. On the contrary, the on-axis pressure minimum approaches the transducer under increasing driving voltages, increasing the distance between the positive and negative peak pressure in the beam. These results are in agreement with numerical KZK model predictions and the existed data of other authors and can be explained according to the effect of self-refraction characteristic of the nonlinear regime of propagation.

Identification of driving network of cellular differentiation from single sample time course gene expression data

NASA Astrophysics Data System (ADS)

Chen, Ye; Wolanyk, Nathaniel; Ilker, Tunc; Gao, Shouguo; Wang, Xujing

Methods developed based on bifurcation theory have demonstrated their potential in driving network identification for complex human diseases, including the work by Chen, et al. Recently bifurcation theory has been successfully applied to model cellular differentiation. However, there one often faces a technical challenge in driving network prediction: time course cellular differentiation study often only contains one sample at each time point, while driving network prediction typically require multiple samples at each time point to infer the variation and interaction structures of candidate genes for the driving network. In this study, we investigate several methods to identify both the critical time point and the driving network through examination of how each time point affects the autocorrelation and phase locking. We apply these methods to a high-throughput sequencing (RNA-Seq) dataset of 42 subsets of thymocytes and mature peripheral T cells at multiple time points during their differentiation (GSE48138 from GEO). We compare the predicted driving genes with known transcription regulators of cellular differentiation. We will discuss the advantages and limitations of our proposed methods, as well as potential further improvements of our methods.

Older drivers and cataract: driving habits and crash risk.

PubMed

Owsley, C; Stalvey, B; Wells, J; Sloane, M E

1999-04-01

Cataract is a leading cause of vision impairment in older adults, affecting almost half of those over age 75 years. Driving is a highly visual task and, as with other age groups, older adults rely on the personal automobile for travel. The purpose of this study was to examine the role of cataract in driving. Older adults (aged 55-85 years) with cataract (n = 279) and those without cataract (n = 105) who were legally licensed to drive were recruited from eye clinics to participate in a driving habits interview to assess driving status, exposure, difficulty, and "space" (the distance of driving excursions from home base). Crash data over the prior 5 years were procured from state records. Visual functional tests documented the severity of vision impairment. Compared to those without cataract, older drivers with cataract were approximately two times more likely to report reductions in days driven and number of destinations per week, driving slower than the general traffic flow, and preferring someone else to drive. Those with cataract were five times more likely to have received advice about limiting their driving. Those with cataract were four times more likely to report difficulty with challenging driving situations, and those reporting driving difficulty were two times more likely to reduce their driving exposure. Drivers with cataract were 2.5 times more likely to have a history of at-fault crash involvement in the prior 5 years (adjusted for miles driven/week and days driven/week). These associations remained even after adjustments for the confounding effects of advanced age, impaired general health, mental status deficit, or depression. Older drivers with cataract experience a restriction in their driving mobility and a decrease in their safety on the road. These findings serve as a baseline for our ongoing study evaluating whether improvements in vision following cataract surgery expand driving mobility and improve driver safety.

Laser dazzling impacts on car driver performance

NASA Astrophysics Data System (ADS)

Steinvall, Ove; Sandberg, Stig; Hörberg, Ulf; Persson, Rolf; Berglund, Folke; Karslsson, Kjell; Öhgren, Johan; Yu, Zhaohua; Söderberg, Per

2013-10-01

A growing problem for the Police and Security Forces has been to prevent potentially hostile individuals to pass a checkpoint, without using lethatl violence. Therefore the question has been if there is a laser or any other strong light source that could be used as a warning and dazzling device, without lethal or long term effects. To investigate the possibilities a field trial has been performed at a motor-racing track. A green CW laser with an irradiance on the eye of maximum 0.5 MPE, as defined by ICNIRP [1] and the ANZI standard [2], was used as a dazzle source. Ten drivers have been driving with dipped headlights through a course of three lines with orange cones. In every line there has been only one gate wide enough to pass without hitting the cones. The time through the course, the choice of gates and the number of cones hit have been measured. For every second trial drive through the track, the driver was exposed to the laser dazzler. The background illuminances ranged from a thousand lux in daylight to about ten millilux in darkness. The protective effect of the sun-visor of the car was investigated. The drives visual system was carefully examined before and after experimental driving and a few weeks after the experimental driving to verify that no pathological effects, that could potentially be induced by the laser exposure, pre-existed or occurred after the laser exposure. An analysis of variance for a within subjects design has been used for evaluation. It was found that green laser light can have an obvious warning effect in daylight. Dazzling does reduce the drivers ability to make judgments and manouver the car in twilight and darkness. A sun-visor can reduce the glare and give the driver an improved control, but that perception can be unjustified. No damage to the visual system was observed.

Nonstationary time series prediction combined with slow feature analysis

NASA Astrophysics Data System (ADS)

Wang, G.; Chen, X.

2015-01-01

Almost all climate time series have some degree of nonstationarity due to external driving forces perturbations of the observed system. Therefore, these external driving forces should be taken into account when reconstructing the climate dynamics. This paper presents a new technique of combining the driving force of a time series obtained using the Slow Feature Analysis (SFA) approach, then introducing the driving force into a predictive model to predict non-stationary time series. In essence, the main idea of the technique is to consider the driving forces as state variables and incorporate them into the prediction model. To test the method, experiments using a modified logistic time series and winter ozone data in Arosa, Switzerland, were conducted. The results showed improved and effective prediction skill.

Enhanced reproducibility of L-mode plasma discharges via physics-model-based q-profile feedback control in DIII-D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schuster, Eugenio J.; Wehner, William P.; Barton, Joseph E.

Recent experiments on DIII-D demonstrate the potential of physics-model-based q-profile control to improve reproducibility of plasma discharges. A combined feed forward + feedback control scheme is employed to optimize the current ramp-up phase by consistently achieving target q profiles (Target 1: q min = 1.3,q 95 = 4:4; Target 2: q min = 1.65,q 95 = 5.0; Target 3: q min = 2.1,q 95 = 6:2) at prescribed times during the plasma formation phase (Target 1: t = 1.5 s; Target 2: t = 1:3 s; Target 3: t = 1.0 s). At the core of the control scheme ismore » a nonlinear, first-principles-driven, physics-based, control-oriented model of the plasma dynamics valid for low confinement (L-mode) scenarios. To prevent undesired L-H transitions, a constraint on the maximum allowable total auxiliary power is imposed in addition to the maximum powers for the individual heating and current-drive sources. Experimental results are presented to demonstrate the effectiveness of the combined feed forward + feedback control scheme to consistently achieve the desired target profiles at the predefined times. Here, these results also show how the addition of feedback control significantly improves upon the feed forward only control solution by reducing the matching error and also how the feedback controller is able to reduce the matching error as the constraint on the maximum allowable total auxiliary power is relaxed while keeping the plasma in L-mode.« less

Enhanced reproducibility of L-mode plasma discharges via physics-model-based q-profile feedback control in DIII-D

DOE PAGES

Schuster, Eugenio J.; Wehner, William P.; Barton, Joseph E.; ...

2017-08-09

Recent experiments on DIII-D demonstrate the potential of physics-model-based q-profile control to improve reproducibility of plasma discharges. A combined feed forward + feedback control scheme is employed to optimize the current ramp-up phase by consistently achieving target q profiles (Target 1: q min = 1.3,q 95 = 4:4; Target 2: q min = 1.65,q 95 = 5.0; Target 3: q min = 2.1,q 95 = 6:2) at prescribed times during the plasma formation phase (Target 1: t = 1.5 s; Target 2: t = 1:3 s; Target 3: t = 1.0 s). At the core of the control scheme ismore » a nonlinear, first-principles-driven, physics-based, control-oriented model of the plasma dynamics valid for low confinement (L-mode) scenarios. To prevent undesired L-H transitions, a constraint on the maximum allowable total auxiliary power is imposed in addition to the maximum powers for the individual heating and current-drive sources. Experimental results are presented to demonstrate the effectiveness of the combined feed forward + feedback control scheme to consistently achieve the desired target profiles at the predefined times. Here, these results also show how the addition of feedback control significantly improves upon the feed forward only control solution by reducing the matching error and also how the feedback controller is able to reduce the matching error as the constraint on the maximum allowable total auxiliary power is relaxed while keeping the plasma in L-mode.« less

Demonstration of a non-contact x-ray source using an inductively heated pyroelectric accelerator

NASA Astrophysics Data System (ADS)

Klopfer, Michael; Satchouk, Vladimir; Cao, Anh; Wolowiec, Thomas; Alivov, Yahya; Molloi, Sabee

2015-04-01

X-ray emission from pyroelectric sources can be produced through non-contact thermal cycling using induction heating. In this study, we demonstrated a proof of concept non-contact x-ray source powered via induction heating. An induction heater operating at 62.5 kHz provided a total of 6.5 W of delivered peak thermal power with 140 V DC of driving voltage. The heat was applied to a ferrous substrate mechanically coupled to a cubic 1 cm3 Lithium Niobate (LiNbO3) pyroelectric crystal maintained in a 3-12 mTorr vacuum. The maximum temperature reached was 175 °C in 86 s of heating. The cooling cycle began immediately after heating and was provided by passive radiative cooling. The total combined cycle time was 250 s. x-ray photons were produced and analyzed in both heating and cooling phases. Maximum photon energies of 59 keV and 55 keV were observed during heating and cooling, respectively. Non-contact devices such as this, may find applications in cancer therapy (brachytherapy), non-destructive testing, medical imaging, and physics education fields.

Stochastic investigation of wind process for climatic variability identification

NASA Astrophysics Data System (ADS)

Deligiannis, Ilias; Tyrogiannis, Vassilis; Daskalou, Olympia; Dimitriadis, Panayiotis; Markonis, Yannis; Iliopoulou, Theano; Koutsoyiannis, Demetris

2016-04-01

The wind process is considered one of the hydrometeorological processes that generates and drives the climate dynamics. We use a dataset comprising hourly wind records to identify statistical variability with emphasis on the last period. Specifically, we investigate the occurrence of mean, maximum and minimum values and we estimate statistical properties such as marginal probability distribution function and the type of decay of the climacogram (i.e., mean process variance vs. scale) for various time periods. Acknowledgement: This research is conducted within the frame of the undergraduate course "Stochastic Methods in Water Resources" of the National Technical University of Athens (NTUA). The School of Civil Engineering of NTUA provided moral support for the participation of the students in the Assembly.

Dynamics of absence seizures

NASA Astrophysics Data System (ADS)

Deeba, Farah; Sanz-Leon, Paula; Robinson, Peter

A neural field model of the corticothalamic system is used to investigate the dynamics of absence seizures in the presence of temporally varying connection strength between the cerebral cortex and thalamus. Variation of connection strength from cortex to thalamus drives the system into seizure once a threshold is passed and a supercritical Hopf bifurcation occurs. The dynamics and spectral characteristics of the resulting seizures are explored as functions of maximum connection strength, time above threshold, and ramp rate. The results enable spectral and temporal characteristics of seizures to be related to underlying physiological variations via nonlinear dynamics and neural field theory. Notably, this analysis adds to neural field modeling of a wide variety of brain activity phenomena and measurements in recent years. Australian Research Council Grants FL1401000225 and CE140100007.

Estimating Hardness from the USDC Tool-Bit Temperature Rise

NASA Technical Reports Server (NTRS)

Bar-Cohen, Yoseph; Sherrit, Stewart

2008-01-01

A method of real-time quantification of the hardness of a rock or similar material involves measurement of the temperature, as a function of time, of the tool bit of an ultrasonic/sonic drill corer (USDC) that is being used to drill into the material. The method is based on the idea that, other things being about equal, the rate of rise of temperature and the maximum temperature reached during drilling increase with the hardness of the drilled material. In this method, the temperature is measured by means of a thermocouple embedded in the USDC tool bit near the drilling tip. The hardness of the drilled material can then be determined through correlation of the temperature-rise-versus-time data with time-dependent temperature rises determined in finite-element simulations of, and/or experiments on, drilling at various known rates of advance or known power levels through materials of known hardness. The figure presents an example of empirical temperature-versus-time data for a particular 3.6-mm USDC bit, driven at an average power somewhat below 40 W, drilling through materials of various hardness levels. The temperature readings from within a USDC tool bit can also be used for purposes other than estimating the hardness of the drilled material. For example, they can be especially useful as feedback to control the driving power to prevent thermal damage to the drilled material, the drill bit, or both. In the case of drilling through ice, the temperature readings could be used as a guide to maintaining sufficient drive power to prevent jamming of the drill by preventing refreezing of melted ice in contact with the drill.

Contributions of physical and cognitive impairments to self-reported driving difficulty in chronic whiplash-associated disorders.

PubMed

Takasaki, Hiroshi; Treleaven, Julia; Johnston, Venerina; Jull, Gwendolen

2013-08-15

Cross-sectional. To conduct a preliminary analysis of the physical, cognitive, and psychological domains contributing to self-reported driving difficulty after adjusting for neck pain, dizziness, and relevant demographics in chronic whiplash-associated disorders (WAD) using hierarchical regression modeling. Pain is a risk factor for car crashes, and dizziness may affect fitness to drive. Both symptoms are common in chronic WAD and difficulty driving is a common complaint in this group. Chronic WAD is often accompanied by physical, cognitive, and psychological impairments. These impairments may contribute to self-reported driving difficulty beyond neck pain, dizziness, and relevant demographics. Forty individuals with chronic WAD participated. Dependent variables were the magnitude of self-reported driving difficulty assessed in the strategic, tactical, and operational levels of the Neck Pain Driving Index. Three models were developed to assess the contributions of independent variables (physical, cognitive, and psychological domains) to each of the 3 dependent variables after adjusting for neck pain intensity, dizziness, and driving demographics. The measures included were: physical domain-range and maximum speed of head rotation, performances during gaze stability, eye-head coordination, and visual dependency tests; cognitive domain-self-reported cognitive symptoms including fatigue and the trail making tests; and psychological domain-general stress, traumatic stress, depression, and fear of neck movements and driving. Symptom duration was relevant to driving difficulty in the strategic and tactical levels. The cognitive domain increased statistical power to estimate the strategic and operational levels (P < 0.1) beyond other contributors. The physical domain increased statistical power to estimate the tactical level (P < 0.1) beyond other contributors. Physical and cognitive impairments independently contributed to self-reported driving difficulty in chronic WAD beyond neck pain, dizziness, and symptom duration. 3.

Observational study of the extent of driving while suspended for alcohol impaired driving

PubMed Central

McCartt, A; Geary, L; Berning, A

2003-01-01

Objective: To determine the proportion of first time driving while alcohol impaired (DWI) offenders who drive while their driver's license is suspended. Design: Systematic, unobtrusive observations were conducted by surveillance professionals from Pinkerton Investigative Services, Inc, of first time offenders in the City of Milwaukee, Wisconsin, and Bergen County, New Jersey. Observations included two four hour periods during suspension (one weekday morning, one Friday/Saturday evening) and two four hour periods after license reinstatement (matched by day of week and time of day). Focus groups of first time offenders were conducted in each site. Setting: New Jersey laws pertaining to license suspension for DWI and driving while suspended are stronger than Wisconsin laws. Subjects: 93 recently convicted first time DWI offenders (57 in Milwaukee and 36 in Bergen County). Main outcome measures: Proportion of subjects observed driving during suspension and after license reinstatement, with reference to all subjects and subjects observed traveling by any means. Results: Of subjects observed traveling while suspended, 88% of Milwaukee subjects compared with 36% of Bergen County subjects drove. Five percent of Milwaukee subjects and 78% of Bergen County subjects reinstated their driver's license. Bergen County subjects were significantly more likely to drive after reinstatement (54%) than during suspension (25%). Conclusion: Prevalence of driving while suspended among first time offenders is high and can vary substantially between jurisdictions. However, the license suspension can have a positive impact on the driving patterns of offenders during suspension, relative to after license reinstatement. Lower prevalence of driving while suspended in New Jersey may partly be attributable to that state's tougher laws. PMID:12810739

What drives uncertainty in model diagnoses of carbon dynamics in southern US forests: climate, vegetation, disturbance, or model parameters?

NASA Astrophysics Data System (ADS)

Zhou, Y.; Gu, H.; Williams, C. A.

2017-12-01

Results from terrestrial carbon cycle models have multiple sources of uncertainty, each with its behavior and range. Their relative importance and how they combine has received little attention. This study investigates how various sources of uncertainty propagate, temporally and spatially, in CASA-Disturbance (CASA-D). CASA-D simulates the impact of climatic forcing and disturbance legacies on forest carbon dynamics with the following steps. Firstly, we infer annual growth and mortality rates from measured biomass stocks (FIA) over time and disturbance (e.g., fire, harvest, bark beetle) to represent annual post-disturbance carbon fluxes trajectories across forest types and site productivity settings. Then, annual carbon fluxes are estimated from these trajectories by using time since disturbance which is inferred from biomass (NBCD 2000) and disturbance maps (NAFD, MTBS and ADS). Finally, we apply monthly climatic scalars derived from default CASA to temporally distribute annual carbon fluxes to each month. This study assesses carbon flux uncertainty from two sources: driving data including climatic and forest biomass inputs, and three most sensitive parameters in CASA-D including maximum light use efficiency, temperature sensitivity of soil respiration (Q10) and optimum temperature identified by using EFAST (Extended Fourier Amplitude Sensitivity Testing). We quantify model uncertainties from each, and report their relative importance in estimating forest carbon sink/source in southeast United States from 2003 to 2010.

Design and Simulation of Scanner Wrapped by Flexible Microcoil Embedded in Polymer Film for Single-Optical Endoscope Application

NASA Astrophysics Data System (ADS)

Zhao, Mengyuan; Yang, Zhuoqing; Xiang, Xiaojian; Sun, Bin; Ding, Guifu; Zhao, Xiaolin

2018-03-01

A single optic fiber scanner with large scanning angle, based on novel electromagnetic driven, is presented. The cylinder magnet and weight are fixed on the fiber, and vibrate under its second-order frequency by driving racetrack coils on the tube. The flexible driving coil is fabricated by uncomplicated planar MEMS technology on polyimide film, and wrapped on the tube. The electromagnetic and mechanical properties of the endoscope system are studied. Experimental results show that the maximum of the second resonant scanning angle is 9.47°.

The Choptank Basin in transition: intensifying agriculture, slow urbanization, and estuarine eutrophication

USDA-ARS?s Scientific Manuscript database

The Choptank basin and estuary are located on the Mid-Atlantic coastal plain on the Delmarva Peninsula. The regional hydrology is characterized by nearly uniform rainfall, but large seasonal variations in temperature and evapotranspiration (maximum in summer) drive large seasonal changes in groundwa...

Research Institute of Complete Electric Drive (Novosibirsk, USSR)

NASA Astrophysics Data System (ADS)

Derbenev, Ya. S.; Kondratenko, A. M.

1989-05-01

The restrictions on the beam emittance and on the imperfectness of the magnetic structure, which are necessary to conserve the beam polarization in accelerators with Siberian snakes are formulated. The trends for changing these criteria with increasing maximum energies and accelerator dimensions at high energies are considered.

Multiroller Traction Drive Speed Reducer. Evaluation for Automotive Gas Turbine Engine

DTIC Science & Technology

1982-06-01

Speed is deLermined by a magnetic pickup on a toothed wheel . Gas turbine engine instrumunelLtiouu i -designed 1f0r measurement of specific fuel...buffer seal and the fluid--film bearing measured a maximum total runout of 0.038 mm (0.0015 in.) at low speed. At higher speeds, above 8000 rpm, the...maximum was 0.025 mm (0.001 in.) except near 10 000 rpm, where the oscilloscope indicated an excursion of 0.045 mm (0.0018 in.). This runout was within

Assessing underwater noise levels during pile-driving at an offshore windfarm and its potential effects on marine mammals.

PubMed

Bailey, Helen; Senior, Bridget; Simmons, Dave; Rusin, Jan; Picken, Gordon; Thompson, Paul M

2010-06-01

Marine renewable developments have raised concerns over impacts of underwater noise on marine species, particularly from pile-driving for wind turbines. Environmental assessments typically use generic sound propagation models, but empirical tests of these models are lacking. In 2006, two 5MW wind turbines were installed off NE Scotland. The turbines were in deep (>40m) water, 25km from the Moray Firth Special Area of Conservation (SAC), potentially affecting a protected population of bottlenose dolphins. We measured pile-driving noise at distances of 0.1 (maximum broadband peak to peak sound level 205dB re 1microPa) to 80km (no longer distinguishable above background noise). These sound levels were related to noise exposure criteria for marine mammals to assess possible effects. For bottlenose dolphins, auditory injury would only have occurred within 100m of the pile-driving and behavioural disturbance, defined as modifications in behaviour, could have occurred up to 50km away.

Resonant-type Smooth Impact Drive Mechanism (SIDM) actuator using a bolt-clamped Langevin transducer.

PubMed

Nishimura, Takuma; Hosaka, Hiroshi; Morita, Takeshi

2012-01-01

The Smooth Impact Drive Mechanism (SIDM) is a linear piezoelectric actuator that has seen practically applied to camera lens modules. Although previous SIDM actuators are easily miniaturized and enable accurate positioning, these actuators cannot actuate at high speed and cannot provide powerful driving because they are driven at an off-resonant frequency using a soft-type PZT. In the present study, we propose a resonant-type SIDM using a bolt-clamped Langevin transducer (BLT) with a hard-type PZT. The resonant-type SIDM overcomes the above-mentioned problems and high-power operation becomes possible with a very simple structure. As a result, we confirmed the operation of resonant-type SIDM by designing a bolt-clamped Langevin transducer. The properties of no-load maximum speed was 0.28m/s at driving voltages of 80V(p-p) for 44.9kHz and 48V(p-p) for 22.45kHz with a pre-load of 3.1N. Copyright © 2011 Elsevier B.V. All rights reserved.

A Novel Assessment of Braking Reaction Time Following THA Using a New Fully Interactive Driving Simulator.

PubMed

Ruel, Allison V; Lee, Yuo-Yu; Boles, John; Boettner, Friedrich; Su, Edwin; Westrich, Geoffrey H

2015-07-01

After total hip replacement surgery, patients are eager to resume the activities of daily life, particularly driving. Most surgeons recommend waiting 6 weeks after surgery to resume driving; however, there is no evidence to indicate that patients cannot resume driving earlier. Our purpose was to evaluate when in the recovery period following THA that patients regain or improve upon their preoperative braking reaction time, allowing them to safely resume driving. We measured and compared pre- and postoperative braking reaction times of 90 patients from 3 different surgeons using a Fully Interactive Driving Simulator (Simulator Systems International, Tulsa, OK). We defined a return to safe braking reaction time as a return to a time value that is either equal to or less than the preoperative braking reaction time. Patients tested at 2 and 3 weeks after surgery had slower braking reaction times than preoperative times by an average of 0.069 and 0.009 s, respectively. At 4 weeks after surgery, however, patients improved their reaction times by 0.035 s (p = 0.0398). In addition, at 2, 3, and 4 weeks postoperatively, the results also demonstrated that patient less than 70 years of age recovered faster. Based upon the results of this study, most patients should be allowed to return to driving 4 weeks following minimally invasive primary total hip arthroplasty.

Trends in reports of driving following illicit drug consumption among regular drug users in Australia, 2007-2013: Has random roadside drug testing had a deterrent effect?

PubMed

Horyniak, Danielle; Dietze, Paul; Lenton, Simon; Alati, Rosa; Bruno, Raimondo; Matthews, Allison; Breen, Courtney; Burns, Lucy

2017-07-01

Driving following illicit drug consumption ('drug-driving') is a potential road safety risk. Roadside drug testing (RDT) is conducted across Australia with the dual aims of prosecuting drivers with drugs in their system and deterring drug-driving. We examined trends over time in self-reported past six-month drug-driving among sentinel samples of regular drug users and assessed the impact of experiences of RDT on drug-driving among these participants. Data from 1913 people who inject drugs (PWID) and 3140 regular psychostimulant users (RPU) who were first-time participants in a series of repeat cross-sectional sentinel studies conducted in Australian capital cities from 2007 to 2013 and reported driving in the past six months were analysed. Trends over time were assessed using the χ 2 test for trend. Multivariable logistic regressions assessed the relationship between experiences of RDT and recent drug-driving, adjusting for survey year, jurisdiction of residence and socio-demographic and drug use characteristics. The percentage of participants reporting recent (past six months) drug-driving decreased significantly over time among both samples (PWID: 83% [2007] vs. 74% [2013], p<0.001; RPU: 72% vs. 56%, p<0.001), but drug-driving remained prevalent. Lifetime experience of RDT increased significantly over time (PWID: 6% [2007] vs. 32% [2013], p<0.001; RPU: 2% vs. 11%, p<0.001). There were no significant associations between experiencing RDT and drug-driving among either PWID or RPU. Although there is some evidence that drug-driving among key risk groups of regular drug users is declining in Australia, possibly reflecting a general deterrent effect of RDT, experiencing RDT appears to have no specific deterrent effect on drug-driving. Further intervention, with a particular focus on changing attitudes towards drug-driving, may be needed to further reduce this practice among these groups. Copyright © 2017 Elsevier Ltd. All rights reserved.

Dense plasma formation on the surface of a ferroelectric induced by a driving pulse with a fast fall time

NASA Astrophysics Data System (ADS)

Chirko, K.; Krasik, Ya. E.; Sayapin, A.; Felsteiner, J.; Bernshtam, V.

2003-08-01

Experimental results are presented of dense plasma formation on the surface of a BaTi-based ferroelectric sample during the fall time of a driving pulse. A negative or positive driving pulse (⩽14 kV), with a slow rise time (˜450 ns) and a fast fall time (40-200 ns), was applied to the rear electrode of the ferroelectric. It was found by different electrical, optical, and spectroscopic diagnostics that this method allows one to form a plasma with a larger density (˜3×1013 cm-3) as compared with that formed by a driving pulse with a fast rise time (⩽4×1012 cm-3). It was shown that the shorter the fall time of the driving pulse the more intense plasma formation occurs. The most uniform and dense plasma formation occurs with a positive driving pulse. In addition, it was found that the shorter the fall time of the positive driving pulse the larger are the current amplitude, the energy, and the divergence of the emitted electrons. The obtained results are discussed in terms of the surface plasma formation and the compensation process of the polarization surface charge of the ferroelectric sample.

The influence of multiple goals on driving behavior: the case of safety, time saving, and fuel saving.

PubMed

Dogan, Ebru; Steg, Linda; Delhomme, Patricia

2011-09-01

Due to the innate complexity of the task drivers have to manage multiple goals while driving and the importance of certain goals may vary over time leading to priority being given to different goals depending on the circumstances. This study aimed to investigate drivers' behavioral regulation while managing multiple goals during driving. To do so participants drove on urban and rural roads in a driving simulator while trying to manage fuel saving and time saving goals, besides the safety goals that are always present during driving. A between-subjects design was used with one group of drivers managing two goals (safety and fuel saving) and another group managing three goals (safety, fuel saving, and time saving) while driving. Participants were provided continuous feedback on the fuel saving goal via a meter on the dashboard. The results indicate that even when a fuel saving or time saving goal is salient, safety goals are still given highest priority when interactions with other road users take place and when interacting with a traffic light. Additionally, performance on the fuel saving goal diminished for the group that had to manage fuel saving and time saving together. The theoretical implications for a goal hierarchy in driving tasks and practical implications for eco-driving are discussed. Copyright © 2011 Elsevier Ltd. All rights reserved.

Slew-rate dependence of tracer magnetization response in magnetic particle imaging.

PubMed

Shah, Saqlain A; Ferguson, R M; Krishnan, K M

2014-10-28

Magnetic Particle Imaging (MPI) is a new biomedical imaging technique that produces real-time, high-resolution tomographic images of superparamagnetic iron oxide nanoparticle tracers. Currently, 25 kHz and 20 mT/μ 0 excitation fields are common in MPI, but lower field amplitudes may be necessary for patient safety in future designs. Here, we address fundamental questions about MPI tracer magnetization dynamics and predict tracer performance in future scanners that employ new combinations of excitation field amplitude ( H o ) and frequency ( ω ). Using an optimized, monodisperse MPI tracer, we studied how several combinations of drive field frequencies and amplitudes affect the tracer's response, using Magnetic Particle Spectrometry and AC hysteresis, for drive field conditions at 15.5, 26, and 40.2 kHz, with field amplitudes ranging from 7 to 52 mT/μ 0 . For both fluid and immobilized nanoparticle samples, we determined that magnetic response was dominated by Néel reversal. Furthermore, we observed that the peak slew-rate ( ωH o ) determined the tracer magnetic response. Smaller amplitudes provided correspondingly smaller field of view, sometimes resulting in excitation of minor hysteresis loops. Changing the drive field conditions but keeping the peak slew-rate constant kept the tracer response almost the same. Higher peak slew-rates led to reduced maximum signal intensity and greater coercivity in the tracer response. Our experimental results were in reasonable agreement with Stoner-Wohlfarth model based theories.

Slew-rate dependence of tracer magnetization response in magnetic particle imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shah, Saqlain A.; Krishnan, K. M., E-mail: kannanmk@uw.edu; Ferguson, R. M.

2014-10-28

Magnetic Particle Imaging (MPI) is a new biomedical imaging technique that produces real-time, high-resolution tomographic images of superparamagnetic iron oxide nanoparticle tracers. Currently, 25 kHz and 20 mT/μ{sub 0} excitation fields are common in MPI, but lower field amplitudes may be necessary for patient safety in future designs. Here, we address fundamental questions about MPI tracer magnetization dynamics and predict tracer performance in future scanners that employ new combinations of excitation field amplitude (H{sub o}) and frequency (ω). Using an optimized, monodisperse MPI tracer, we studied how several combinations of drive field frequencies and amplitudes affect the tracer's response, using Magnetic Particlemore » Spectrometry and AC hysteresis, for drive field conditions at 15.5, 26, and 40.2 kHz, with field amplitudes ranging from 7 to 52 mT/μ{sub 0}. For both fluid and immobilized nanoparticle samples, we determined that magnetic response was dominated by Néel reversal. Furthermore, we observed that the peak slew-rate (ωH{sub o}) determined the tracer magnetic response. Smaller amplitudes provided correspondingly smaller field of view, sometimes resulting in excitation of minor hysteresis loops. Changing the drive field conditions but keeping the peak slew-rate constant kept the tracer response almost the same. Higher peak slew-rates led to reduced maximum signal intensity and greater coercivity in the tracer response. Our experimental results were in reasonable agreement with Stoner-Wohlfarth model based theories.« less

Respiratory drives and exercise in menstrual cycles of athletic and nonathletic women.

PubMed

Schoene, R B; Robertson, H T; Pierson, D J; Peterson, A P

1981-06-01

To investigate the influence of the midluteal and midfollicular phases of the menstrual cycle on exercise performance and ventilatory drives, we studied six outstanding female athletes, six controls with normal menstrual cycles, and six outstanding athletes who were amenorrheic. In all menstruating subjects resting minute ventilation (Ve) and mouth occlusion pressures (P0.1) were higher in the luteal phase (p less than k0.0001 and p less than 0.02, respectively),. Hypoxic (expressed as the hyperbolic shape parameter A) and hypercapnic (expressed as S, deltaVE/delta PAco2) ventilatory responses were increase in the luteal phase (p less than 0.01). The athletes had lower A values during the luteal phase than the nonathletes (p less than 0.001). Maximal exercise response, expressed either as total exercise time or maximum O2 consumption or CO2 production (VO2 max or Vco2 max) was decreased during the luteal phase but was significantly different at a p less than 0.05 level only among the nonathletes. Ventilatory equivalent (VE/VO2) during progressive exercise on a bicycle ergometer was significantly increased during the luteal phase. The amenorrheic athletes showed no changes between the two test periods. The luteal phase of the menstrual cycle induced increases in ventilatory drives and exercise ventilation in both athletes and controls, but the athletes, in contrast to controls, demonstrated no significant decrease in exercise performance in the luteal phase.

A Randomized Controlled Trial of a Telephone Intervention for Alcohol Misuse with Injured Emergency Department Patients

PubMed Central

Mello, Michael J.; Baird, Janette; Lee, Christina; Strezsak, Valerie; French, Michael T.; Longabaugh, Richard

2015-01-01

Objective This was a randomized controlled trial to test efficacy of a telephone intervention (TBMI) for injured ED patients with alcohol misuse to decrease alcohol use, impaired driving, alcohol-related injuries and alcohol-related negative consequences. Methods ED patients screening positive for alcohol misuse were randomized to a three-session telephone brief motivational intervention on alcohol (TBMI) delivered by a counselor trained in motivational interviewing over 6 weeks or a control intervention of a scripted home fire and burn safety education delivered in three calls. Patients were followed for 12 months and assessed for changes in alcohol use, impaired driving, alcohol-related injuries and alcohol-related negative consequences. Results 730 ED patients were randomized; 78% received their assigned intervention by telephone and of those, 72% completed 12 months assessments. There were no differential benefits of TBMI intervention versus assessment and a control intervention in all three variables of alcohol use (frequency of binge alcohol use over the prior 30 days, maximum number of drinks at one time in past 30 days, typical alcohol use in past 30 days), alcohol impaired driving, alcohol related injuries and alcohol-related negative consequences. Conclusions Despite the potential advantage of delivering a TBMI in not disrupting ED clinical care, our study found no efficacy for it over an assessment and control intervention. Potential etiologies for our finding include that injury itself or alcohol assessments, or the control intervention had active ingredients for alcohol change. PMID:26585044

Comprehensive and Practical Vision System for Self-Driving Vehicle Lane-Level Localization.

PubMed

Du, Xinxin; Tan, Kok Kiong

2016-05-01

Vehicle lane-level localization is a fundamental technology in autonomous driving. To achieve accurate and consistent performance, a common approach is to use the LIDAR technology. However, it is expensive and computational demanding, and thus not a practical solution in many situations. This paper proposes a stereovision system, which is of low cost, yet also able to achieve high accuracy and consistency. It integrates a new lane line detection algorithm with other lane marking detectors to effectively identify the correct lane line markings. It also fits multiple road models to improve accuracy. An effective stereo 3D reconstruction method is proposed to estimate vehicle localization. The estimation consistency is further guaranteed by a new particle filter framework, which takes vehicle dynamics into account. Experiment results based on image sequences taken under different visual conditions showed that the proposed system can identify the lane line markings with 98.6% accuracy. The maximum estimation error of the vehicle distance to lane lines is 16 cm in daytime and 26 cm at night, and the maximum estimation error of its moving direction with respect to the road tangent is 0.06 rad in daytime and 0.12 rad at night. Due to its high accuracy and consistency, the proposed system can be implemented in autonomous driving vehicles as a practical solution to vehicle lane-level localization.

Eye blink detection for different driver states in conditionally automated driving and manual driving using EOG and a driver camera.

PubMed

Schmidt, Jürgen; Laarousi, Rihab; Stolzmann, Wolfgang; Karrer-Gauß, Katja

2018-06-01

In this article, we examine the performance of different eye blink detection algorithms under various constraints. The goal of the present study was to evaluate the performance of an electrooculogram- and camera-based blink detection process in both manually and conditionally automated driving phases. A further comparison between alert and drowsy drivers was performed in order to evaluate the impact of drowsiness on the performance of blink detection algorithms in both driving modes. Data snippets from 14 monotonous manually driven sessions (mean 2 h 46 min) and 16 monotonous conditionally automated driven sessions (mean 2 h 45 min) were used. In addition to comparing two data-sampling frequencies for the electrooculogram measures (50 vs. 25 Hz) and four different signal-processing algorithms for the camera videos, we compared the blink detection performance of 24 reference groups. The analysis of the videos was based on very detailed definitions of eyelid closure events. The correct detection rates for the alert and manual driving phases (maximum 94%) decreased significantly in the drowsy (minus 2% or more) and conditionally automated (minus 9% or more) phases. Blinking behavior is therefore significantly impacted by drowsiness as well as by automated driving, resulting in less accurate blink detection.

30 CFR 77.1602 - Use of aerial tramways to transport persons.

Code of Federal Regulations, 2010 CFR

2010-07-01

... other than maintenance men shall not ride empty buckets on aerial tramways unless the following features are provided: (a) Two independent brakes, each capable of holding the maximum load. (b) Direct communication between terminals. (c) Power drives with emergency power available in case of primary power...

Lake Shore Drive\\\\Grand Ave.\\\\E. Illinois Ave., May 2016, Lindsay Light Radiological Survey

EPA Pesticide Factsheets

Field gamma measurements process did not exceed the instrument threshold. Unshielded readings ranged from a minimumof 4,600 cpm to a maximum of 14,200 cpm unshielded and shielded readings ranged from a minimum of1,800 cpm to 2,680 cpm.

Two-step activation of paper batteries for high power generation: design and fabrication of biofluid- and water-activated paper batteries

NASA Astrophysics Data System (ADS)

Lee, Ki Bang

2006-11-01

Two-step activation of paper batteries has been successfully demonstrated to provide quick activation and to supply high power to credit card-sized biosystems on a plastic chip. A stack of a magnesium layer (an anode), a fluid guide (absorbent paper), a highly doped filter paper with copper chloride (a cathode) and a copper layer as a current collector is laminated between two transparent plastic films into a high power biofluid- and water-activated battery. The battery is activated by two-step activation: (1) after placing a drop of biofluid/water-based solution on the fluid inlet, the surface tension first drives the fluid to soak the fluid guide; (2) the fluid in the fluid guide then penetrates into the heavily doped filter paper with copper chloride to start the battery reaction. The fabricated half credit card-sized battery was activated by saliva, urine and tap water and delivered a maximum voltage of 1.56 V within 10 s after activation and a maximum power of 15.6 mW. When 10 kΩ and 1 KΩ loads are used, the service time with water, urine and saliva is measured as more than 2 h. An in-series battery of 3 V has been successfully tested to power two LEDs (light emitting diodes) and an electric driving circuit. As such, this high power paper battery could be integrated with on-demand credit card-sized biosystems such as healthcare test kits, biochips, lab-on-a-chip, DNA chips, protein chips or even test chips for water quality checking or chemical checking.

Prolonged Heavy Vehicle Driving Performance: Effects of Unpredictable Shift Onset and Duration and Convoy versus Independent Driving Conditions

DTIC Science & Technology

1983-09-01

increase time headway. An impli- cation of this interpretation for driving safety is that where fatigued driv- ers are unable to compensate in this way...of driving safety these results provide an indi- cation of circumstances in which time headway is particularly short. Not surprisingly this measure is

The reaction times of drivers aged 20 to 80 during a divided attention driving.

PubMed

Svetina, Matija

2016-11-16

Many studies addressing age-related changes in driving performance focus on comparing young vs. older drivers, which might lead to the biased conclusion that driving performance decreases only after the age of 65. The main aim of the study was to show that changes in driving performance are progressive throughout the adult years. A sample of 351 drivers aged 20 to 80 was assessed for their reaction times while driving between road cones. The drivers were exposed to 2 conditions varying according to task complexity. In single task conditions, the drivers performed a full stopping maneuver at a given signal; in dual task conditions, the drivers were distracted before the signal for stopping maneuver was triggered. Reaction times were compared across conditions and age groups. The results showed that both reaction times and variability of driving performance increased progressively between the ages of 20 and 80. The increase in both reaction times and variability was greater in the complex task condition. The high-performing quarter of elderly drivers performed equally well or better than younger drivers did. The data clearly supported the claim that driving performance changes steadily across age groups: both mean reaction time and interindividual variability progressively increase with age. In addition, a significant group of older drivers was identified who did not show the expected age-related decrease in performance. The findings have important implications, suggesting that in relation to driving, aging is a progressive phenomenon and may lead to variety of driving performance; age-related studies of driving performance should put more emphasis on investigating changes across the whole driver age range rather than only comparing younger and older drivers.

Geographic isolation drives divergence of uncorrelated genetic and song variation in the Ruddy-capped Nightingale-Thrush (Catharus frantzii; Aves: Turdidae).

PubMed

Ortiz-Ramírez, Marco F; Andersen, Michael J; Zaldívar-Riverón, Alejandro; Ornelas, Juan Francisco; Navarro-Sigüenza, Adolfo G

2016-01-01

Montane barriers influence the evolutionary history of lineages by promoting isolation of populations. The effects of these historical processes are evident in patterns of differentiation among extant populations, which are often expressed as genetic and behavioral variation between populations. We investigated the effects of geographic barriers on the evolutionary history of a Mesoamerican bird by studying patterns of genetic and vocal variation in the Ruddy-capped Nightingale-Thrush (Turdidae: Catharus frantzii), a non-migratory oscine bird that inhabits montane forests from central Mexico to Panama. We reconstructed the phylogeographic history and estimated divergence times between populations using Bayesian and maximum likelihood methods. We found strong support for the existence of four mitochondrial lineages of C. frantzii corresponding to isolated mountain ranges: Sierra Madre Oriental; Sierra Madre del Sur; the highlands of Chiapas, Guatemala, and El Salvador; and the Talamanca Cordillera. Vocal features in C. frantzii were highly variable among the four observed clades, but vocal variation and genetic variation were uncorrelated. Song variation in C. frantzii suggests that sexual selection and cultural drift could be important factors driving song differentiation in C. frantzii. Copyright © 2015 Elsevier Inc. All rights reserved.

Towards a universal description of cohesive-particle flows

NASA Astrophysics Data System (ADS)

Lamarche, Casey; Liu, Peiyuan; Kellogg, Kevin; Lattanzi, Aaron; Hrenya, Christine

2017-11-01

A universal framework for describing cohesive granular flows seems unattainable based on prior works, making a fundamental continuum theory to predict such flows appear unachievable. For the first time, universal behavior of cohesive-grain flows is demonstrated by linking the macroscopic (many-grain) behavior to grain-grain interactions via two dimensionless groups: a generalized Bond number BoG - ratio of maximum cohesive force to the force driving flow - and a new Agglomerate number Ag - ratio of critical cohesive energy to the granular energy. Cohesive-grain flow is investigated in several systems, and universal behavior is determined via collapse of a cohesion-dependent output variable from each system with the appropriate dimensionless group. Universal behavior is observed using BoG for dense (enduring-contact-dominated) flows and Ag for dilute (collision-dominated) flows, as BoG accounts for the cohesive contact force and Ag for increased collisional dissipation due to cohesion. Hence, a new physical picture is presented, namely, BoG dominates in dense flows, where force chains drive momentum transfer, and Ag dominates in dilute systems, where the dissipative collisions dominate momentum transfer. Apparent discrepancies with past treatments are resolved. Dow Corning Corporation.

Solution of task related to control of swiss-type automatic lathe to get planes parallel to part axis

NASA Astrophysics Data System (ADS)

Tabekina, N. A.; Chepchurov, M. S.; Evtushenko, E. I.; Dmitrievsky, B. S.

2018-05-01

The work solves the problem of automation of machining process namely turning to produce parts having the planes parallel to an axis of rotation of part without using special tools. According to the results, the availability of the equipment of a high speed electromechanical drive to control the operative movements of lathe machine will enable one to get the planes parallel to the part axis. The method of getting planes parallel to the part axis is based on the mathematical model, which is presented as functional dependency between the conveying velocity of the driven element and the time. It describes the operative movements of lathe machine all over the tool path. Using the model of movement of the tool, it has been found that the conveying velocity varies from the maximum to zero value. It will allow one to carry out the reverse of the drive. The scheme of tool placement regarding the workpiece has been proposed for unidirectional movement of the driven element at high conveying velocity. The control method of CNC machines can be used for getting geometrically complex parts on the lathe without using special milling tools.

Quantum gates by periodic driving

PubMed Central

Shi, Z. C.; Wang, W.; Yi, X. X.

2016-01-01

Topological quantum computation has been extensively studied in the past decades due to its robustness against decoherence. One way to realize the topological quantum computation is by adiabatic evolutions—it requires relatively long time to complete a gate, so the speed of quantum computation slows down. In this work, we present a method to realize single qubit quantum gates by periodic driving. Compared to adiabatic evolution, the single qubit gates can be realized at a fixed time much shorter than that by adiabatic evolution. The driving fields can be sinusoidal or square-well field. With the sinusoidal driving field, we derive an expression for the total operation time in the high-frequency limit, and an exact analytical expression for the evolution operator without any approximations is given for the square well driving. This study suggests that the period driving could provide us with a new direction in regulations of the operation time in topological quantum computation. PMID:26911900

Quantum gates by periodic driving.

PubMed

Shi, Z C; Wang, W; Yi, X X

2016-02-25

Topological quantum computation has been extensively studied in the past decades due to its robustness against decoherence. One way to realize the topological quantum computation is by adiabatic evolutions-it requires relatively long time to complete a gate, so the speed of quantum computation slows down. In this work, we present a method to realize single qubit quantum gates by periodic driving. Compared to adiabatic evolution, the single qubit gates can be realized at a fixed time much shorter than that by adiabatic evolution. The driving fields can be sinusoidal or square-well field. With the sinusoidal driving field, we derive an expression for the total operation time in the high-frequency limit, and an exact analytical expression for the evolution operator without any approximations is given for the square well driving. This study suggests that the period driving could provide us with a new direction in regulations of the operation time in topological quantum computation.

Solution-processed small molecules as mixed host for highly efficient blue and white phosphorescent organic light-emitting diodes.

PubMed

Fu, Qiang; Chen, Jiangshan; Shi, Changsheng; Ma, Dongge

2012-12-01

The widely used hole-transporting host 4,4',4″-tris(N-carbazolyl)-triphenylamine (TCTA) blended with either a hole-transporting or an electron-transporting small-molecule material as a mixed-host was investigated in the phosphorescent organic light-emitting diodes (OLEDs) fabricated by the low-cost solution-process. The performance of the solution-processed OLEDs was found to be very sensitive to the composition of the mixed-host systems. The incorporation of the hole-transporting 1,1-bis[(di-4-tolylamino)phenyl]cyclohexane (TAPC) into TCTA as the mixed-host was demonstrated to greatly reduce the driving voltage and thus enhance the efficiency due to the improvement of hole injection and transport. On the basis of the mixed-host of TCTA:TAPC, we successfully fabricated low driving voltage and high efficiency blue and white phosphorescent OLEDs. A maximum forward viewing current efficiency of 32.0 cd/A and power efficiency of 25.9 lm/W were obtained in the optimized mixed-host blue OLED, which remained at 29.6 cd/A and 19.1 lm/W at the luminance of 1000 cd/m(2) with a driving voltage as low as 4.9 V. The maximum efficiencies of 37.1 cd/A and 32.1 lm/W were achieved in a single emissive layer white OLED based on the TCTA:TAPC mixed-host. Even at 1000 cd/m(2), the efficiencies still reach 34.2 cd/A and 23.3 lm/W and the driving voltage is only 4.6 V, which is comparable to those reported from the state-of-the-art vacuum-evaporation deposited white OLEDs.

Observation of a Time Quasicrystal and Its Transition to a Superfluid Time Crystal.

PubMed

Autti, S; Eltsov, V B; Volovik, G E

2018-05-25

We report experimental realization of a quantum time quasicrystal and its transformation to a quantum time crystal. We study Bose-Einstein condensation of magnons, associated with coherent spin precession, created in a flexible trap in superfluid ^{3}He-B. Under a periodic drive with an oscillating magnetic field, the coherent spin precession is stabilized at a frequency smaller than that of the drive, demonstrating spontaneous breaking of discrete time translation symmetry. The induced precession frequency is incommensurate with the drive, and hence, the obtained state is a time quasicrystal. When the drive is turned off, the self-sustained coherent precession lives a macroscopically long time, now representing a time crystal with broken symmetry with respect to continuous time translations. Additionally, the magnon condensate manifests spin superfluidity, justifying calling the obtained state a time supersolid or a time supercrystal.

Observation of a Time Quasicrystal and Its Transition to a Superfluid Time Crystal

NASA Astrophysics Data System (ADS)

Autti, S.; Eltsov, V. B.; Volovik, G. E.

2018-05-01

We report experimental realization of a quantum time quasicrystal and its transformation to a quantum time crystal. We study Bose-Einstein condensation of magnons, associated with coherent spin precession, created in a flexible trap in superfluid 3He-B . Under a periodic drive with an oscillating magnetic field, the coherent spin precession is stabilized at a frequency smaller than that of the drive, demonstrating spontaneous breaking of discrete time translation symmetry. The induced precession frequency is incommensurate with the drive, and hence, the obtained state is a time quasicrystal. When the drive is turned off, the self-sustained coherent precession lives a macroscopically long time, now representing a time crystal with broken symmetry with respect to continuous time translations. Additionally, the magnon condensate manifests spin superfluidity, justifying calling the obtained state a time supersolid or a time supercrystal.

Chronotype-dependent circadian rhythmicity of driving safety.

PubMed

Del Rio-Bermudez, Carlos; Diaz-Piedra, Carolina; Catena, Andrés; Buela-Casal, Gualberto; Di Stasi, Leandro Luigi

2014-05-01

Among the factors associated with driving safety, sleep-related variables constitute a leading cause of road accidents. Circadian fluctuations of driver's somnolence has been previously linked to road safety. However, the role of chronotype in this relationship has been poorly investigated. Thus, the aim of the present work was to address whether driving performance is influenced by circadian patterns, in turn modulated by the driver's chronotype and the time of day (i.e. synchrony effect). We assessed 47 healthy young adults with specific chronotypes in several simulated driving sessions, both in the morning and in the evening. We collected driving performance data, along with self-reported levels of activation prior to each driving session and other sleep-related variables. Participants drove less safely when testing times took place outside their optimal time of day, as determined by their chronotype and confirmed by self-reported levels of activation. These differences were more pronounced in the morning, when morning types shown a better driving performance. Our results suggest that chronotype plays an important role as a modulator of the relationship between the time of day and driving safety. Therefore, it is necessary to acknowledge this variable in theoretical models of driving behavior, and for the improvement of occupational accidents prevention programs.

Study the adsorption of sulfates by high cross-linked polystyrene divinylbenzene anion-exchange resin

NASA Astrophysics Data System (ADS)

Fathy, Mahmoud; Moghny, Th. Abdel; Awadallah, Ahmed E.; El-Bellihi, Abdel-Hameed A.-A.

2017-03-01

In response to rising concerns about the effect of sulfate on water quality, human health, and agriculture, many jurisdictions around the world are imposing tighter regulations for sulfate discharge. This is driving the need for environmental compliance in industries like mining, metal processing, pulp and paper, sewage treatment, and chemical manufacturing. The sulfate removal from synthetic water by high cross-linked polystyrene divinylbenzene resin was studied at batch experiments in this study. The effect of pH, contact time, sulfates concentration, and adsorbent dose on the sulfate sequestration was investigated. The optimum conditions were studied on Saline water as a case study. The results showed that with increasing of the absorbent amount; contact time, and pH improve the efficiency of sulfate removal. The maximum sulfates uptake was obtained in pH and contact time 3.0 and 120 min, respectively. Also, with increasing initial concentration of sulfates in water, the efficiency of sulfate removal decreased. The obtained results in this study were matched with Freundlich isotherm and pseudo-second-order kinetic. The maximum adsorption capacity (Qm) and constant rate were found 0.318 (mg/g) and 0.21 (mg/g.min), respectively. This study also showed that in the optimum conditions, the sulfate removal efficiency from Saline water by 0.1 mg/L sulfates was 65.64 %. Eventually, high cross-linked polystyrene divinylbenzene resin is recommended as a suitable and low cost absorbent to sulfate removal from aqueous solutions.

The influence of drinking, texting, and eating on simulated driving performance.

PubMed

Irwin, Christopher; Monement, Sophie; Desbrow, Ben

2015-01-01

Driving is a complex task and distractions such as using a mobile phone for the purpose of text messaging are known to have a significant impact on driving. Eating and drinking are common forms of distraction that have received less attention in relation to their impact on driving. The aim of this study was to further explore and compare the effects of a variety of distraction tasks (i.e., text messaging, eating, drinking) on simulated driving. Twenty-eight healthy individuals (13 female) participated in a crossover design study involving 3 experimental trials (separated by ≥24 h). In each trial, participants completed a baseline driving task (no distraction) before completing a second driving task involving one of 3 different distraction tasks (drinking 400 mL water, drinking 400 mL water and eating a 6-inch Subway sandwich, drinking 400 mL water and composing 3 text messages). Primary outcome measures of driving consisted of standard deviation of lateral position (SDLP) and reaction time to auditory and visual critical events. Subjective ratings of difficulty in performing the driving tasks were also collected at the end of the study to determine perceptions of distraction difficulty on driving. Driving tasks involving texting and eating were associated with significant impairment in driving performance measures for SDLP compared to baseline driving (46.0 ± 0.08 vs. 41.3 ± 0.06 cm and 44.8 ± 0.10 vs. 41.6 ± 0.07 cm, respectively), number of lane departures compared to baseline driving (10.9 ± 7.8 vs. 7.6 ± 7.1 and 9.4 ± 7.5 vs. 7.1 ± 7.0, respectively), and auditory reaction time compared to baseline driving (922 ± 95 vs. 889 ± 104 ms and 933 ± 101 vs. 901 ± 103 ms, respectively). No difference in SDLP (42.7 ± 0.08 vs. 42.5 ± 0.07 cm), number of lane departures (7.6 ± 7.7 vs. 7.0 ± 6.8), or auditory reaction time (891 ± 98 and 885 ± 89 ms) was observed in the drive involving the drink-only condition compared to the corresponding baseline drive. No difference in reaction time to visual stimuli was observed between baseline and experimental drives for any of the trial conditions. Participants' subjective ratings indicated that they perceived the texting while driving condition to be the most difficult despite similar magnitudes of impairment observed with the eating while driving condition. Distracting behaviors such as eating and texting while driving appear to negatively impact driving measures of lane position control and reaction time. These findings may have direct implications for motorists that engage in these types of distracting behaviors behind the wheel and for the safety of other road users.

Structural barriers to comprehensive, coordinated HIV care: geographic accessibility in the US South.

PubMed

Kimmel, April D; Masiano, Steven P; Bono, Rose S; Martin, Erika G; Belgrave, Faye Z; Adimora, Adaora A; Dahman, Bassam; Galadima, Hadiza; Sabik, Lindsay M

2018-05-30

Structural barriers to HIV care are particularly challenging in the US South, which has higher HIV diagnosis rates, poverty, uninsurance, HIV stigma, and rurality, and fewer comprehensive public health programs versus other US regions. Focusing on one structural barrier, we examined geographic accessibility to comprehensive, coordinated HIV care (HIVCCC) in the US South. We integrated publicly available data to study travel time to HIVCCC in 16 Southern states and District of Columbia. We geocoded HIVCCC service locations and estimated drive time between the population-weighted county centroid and closest HIVCCC facility. We evaluated drive time in aggregate, and by county-level HIV prevalence quintile, urbanicity, and race/ethnicity. Optimal drive time was ≤30 min, a common primary care accessibility threshold. We identified 228 service locations providing HIVCCC across 1422 Southern counties, with median drive time to care of 70 min (IQR 64 min). For 368 counties in the top HIV prevalence quintile, median drive time is 50 min (IQR 61 min), exceeding 60 min in over one-third of these counties. Among counties in the top HIV prevalence quintile, drive time to care is six-folder higher for rural versus super-urban counties. Counties in the top HIV prevalence quintiles for non-Hispanic Blacks and for Hispanics have >50% longer drive time to care versus for non-Hispanic Whites. Including another potential care source-publicly-funded health centers serving low-income populations-could double the number of high-HIV burden counties with drive time ≤30 min, representing nearly 35,000 additional people living with HIV with accessible HIVCCC. Geographic accessibility to HIVCCC is inadequate in the US South, even in high HIV burden areas, and geographic and racial/ethnic disparities exist. Structural factors, such as geographic accessibility to care, may drive disparities in health outcomes. Further research on programmatic policies, and evidence-based alternative HIV care delivery models improving access to care, is critical.

Dynamic Simulation Research on Chain Drive Mechanism of Corn Seeder Based on ADAMS

NASA Astrophysics Data System (ADS)

Wang, Y. B.; Jia, H. P.

2017-12-01

In order to reduce the damage to the chain and improve the seeding quality of the seeding machine, the corn seeder has the characteristics of the seeding quality and some technical indexes in the work of the corn seeding machine. The dynamic analysis of the chain drive mechanism is carried out by using the dynamic virtual prototype. In this paper, the speed of the corn planter is 5km/h, and the speed of the simulated knuckle is 0.1~0.9s. The velocity is 0.12m/s, which is equal to the chain speed when the seeder is running normally. Of the dynamic simulation of the movement and the actual situation is basically consistent with the apparent speed of the drive wheel has changed the acceleration and additional dynamic load, the chain drive has a very serious damage, and the maximum load value of 47.28N, in order to reduce the damage to the chain, As far as possible so that the sowing machine in the work to maintain a reasonable uniform speed, to avoid a greater acceleration, the corn sowing machine drive the design of a certain reference.

Driving: a road to unhealthy lifestyles and poor health outcomes.

PubMed

Ding, Ding; Gebel, Klaus; Phongsavan, Philayrath; Bauman, Adrian E; Merom, Dafna

2014-01-01

Driving is a common part of modern society, but its potential effects on health are not well understood. The present cross-sectional study (n = 37,570) examined the associations of driving time with a series of health behaviors and outcomes in a large population sample of middle-aged and older adults using data from the Social, Economic, and Environmental Factor Study conducted in New South Wales, Australia, in 2010. Multiple logistic regression was used in 2013 to examine the associations of usual daily driving time with health-related behaviors (smoking, alcohol use, diet, physical activity, sedentary behavior, sleep) and outcomes (obesity, general health, quality of life, psychological distress, time stress, social functioning), adjusted for socio-demographic characteristics. Findings suggested that longer driving time was associated with higher odds for smoking, insufficient physical activity, short sleep, obesity, and worse physical and mental health. The associations consistently showed a dose-response pattern and more than 120 minutes of driving per day had the strongest and most consistent associations with the majority of outcomes. This study highlights driving as a potential lifestyle risk factor for public health. More population-level multidisciplinary research is needed to understand the mechanism of how driving affects health.

[Effect of air-electric fields on driving and reaction patterns. Test subjects in the car driving simulator (author's transl)].

PubMed

Anselm, D; Danner, M; Kirmaier, N; König, H L; Müller-Limmroth, W; Reis, A; Schauerte, W

1977-06-10

In the relevant frequency range of about 10 Hertz cars can be considered very largely as Faraday cages and consequently as screens against air-electric fields. This may have a negative influence on driving and reaction patterns as a result. In an extensive investigation 48 subjects in a driving simulator were exposed to definite artificially produced air-electric fields. The self-rating of the performance and concentration of the subjects, reaction times and driving errors were determined. While the reaction times remained practically constant, the driving behavior of the subjects improved.

Time pressure and regulations on hospital-in-the-home (HITH) nurses: An on-the-road study.

PubMed

Cœugnet, Stéphanie; Forrierre, Justine; Naveteur, Janick; Dubreucq, Catherine; Anceaux, Françoise

2016-05-01

This study investigated both causal factors and consequences of time pressure in hospital-in-the-home (HITH) nurses. These nurses may experience additional stress from the time pressure they encounter while driving to patients' homes, which may result in greater risk taking while driving. From observation in natural settings, data related to the nurses' driving behaviours and emotions were collected and analysed statistically; semi-directed interviews with the nurses were analysed qualitatively. The results suggest that objective time constraints alone do not necessarily elicit subjective time pressure. The challenges and uncertainty associated with healthcare and the driving period contribute to the emergence of this time pressure, which has a negative impact on both the nurses' driving and their emotions. Finally, the study focuses on anticipated and in situ regulations. These findings provide guidelines for organizational and technical solutions allowing the reduction of time pressure among HITH nurses. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Cell Phone Ring Suppression and HUD Caller ID: Effectiveness in Reducing Momentary Driver Distraction under Varying Workload Levels

NASA Astrophysics Data System (ADS)

Nowakowski, C.; Friedman, D.; Green, P.

2001-10-01

The purpose of the current experiment is to provide a preliminary driving simulator assessment of several hands-free design solutions with regard to the task of answering the phone while driving. Specifically, the following questions were examined: (1) Does the location of a caller ID display and the phone buttons (two HUD (Head Up Display) locations vs. phone cradle) affect either the time to answer the phone or driving performance; (2) Does the presence or absence of a ring affect either the time to answer the phone or driving performance; (3) Does increased driving workload (visual demand) affect either the time to answer the phone or driving performance; (4) What were the initial driver reactions to a HUD-based call timer.

Parkinson's disease and driving ability

PubMed Central

Singh, Rajiv; Pentland, Brian; Hunter, John; Provan, Frances

2007-01-01

Objectives To explore the driving problems associated with Parkinson's disease (PD) and to ascertain whether any clinical features or tests predict driver safety. Methods The driving ability of 154 individuals with PD referred to a driving assessment centre was determined by a combination of clinical tests, reaction times on a test rig and an in‐car driving test. Results The majority of cases (104, 66%) were able to continue driving although 46 individuals required an automatic transmission and 10 others needed car modifications. Ability to drive was predicted by the severity of physical disease, age, presence of other associated medical conditions, particularly dementia, duration of disease, brake reaction, time on a test rig and score on a driving test (all p<0.001). The level of drug treatment and the length of driving history were not correlated. Discriminant analysis revealed that the most important features in distinguishing safety to drive were severe physical disease (Hoehn and Yahr stage 3), reaction time, moderate disease associated with another medical condition and high score on car testing. Conclusions Most individuals with PD are safe to drive, although many benefit from car modifications or from using an automatic transmission. A combination of clinical tests and in‐car driving assessment will establish safety to drive, and a number of clinical correlates can be shown to predict the likely outcome and may assist in the decision process. This is the largest series of consecutive patients seen at a driving assessment centre reported to date, and the first to devise a scoring system for on‐road driving assessment. PMID:17178820

H1 antihistamines and driving.

PubMed

Popescu, Florin Dan

2008-01-01

Driving performances depend on cognitive, psychomotor and perception functions. The CNS adverse effects of some H1 antihistamines can alter the patient ability to drive. Data from studies using standardized objective cognitive and psychomotor tests (Choice Reaction Time, Critical Flicker Fusion. Digital Symbol Substitution Test), functional brain imaging (Positron Emission Tomography, functional Magnetic Resonance Imaging), neurophysiological studies (Multiple Sleep Latency Test, auditory and visual evoked potentials), experimental simulated driving (driving simulators) and real driving studies (the Highway Driving Test, with the evaluation of the Standard Deviation Lateral Position, and the Car Following Test, with the measurement of the Brake Reaction Time) must be discussed in order to classify a H1 antihistamine as a true non-sedating one.

H1 antihistamines and driving

PubMed Central

Florin-Dan, Popescu

2008-01-01

Driving performances depend on cognitive, psychomotor and perception functions. The CNS adverse effects of some H1 antihistamines can alter the patient ability to drive. Data from studies using standardized objective cognitive and psychomotor tests (Choice Reaction Time, Critical Flicker Fusion, Digital Symbol Substitution Test), functional brain imaging (Positron Emission Tomography, functional Magnetic Resonance Imaging), neurophysiological studies (Multiple Sleep Latency Test, auditory and visual evoked potentials), experimental simulated driving (driving simulators) and real driving studies (the Highway Driving Test, with the evaluation of the Standard Deviation Lateral Position, and the Car Following Test, with the measurement of the Brake Reaction Time) must be discussed in order to classify a H1 antihistamine as a true non-sedating one. PMID:20108503

Observational study of the extent of driving while suspended for alcohol-impaired driving

DOT National Transportation Integrated Search

2002-09-01

A study was undertaken to determine the proportion of first-time alcohol-impaired driving offenders who drive while suspended and the circumstances and motivations for driving. Systematic, unobtrusive observations were conducted by surveillance profe...

A descriptive retrospective study of time consumption in home care services: how do employees use their working time?

PubMed

Holm, Solrun G; Angelsen, Ragnhild O

2014-09-26

Home care services in Norway are provided for free, and municipalities are responsible for their provision to all those in need of them, in accordance with the Act on Municipal Health and Care Services. The costs of home care services are increasing. Many municipalities are now working to find the best cost-effective solutions to ensure that home care services are of sufficient quality but still affordable. This paper describes how nurses and health workers spend their working time, with a hypothesis that driving time and time required to document details of the care given are underestimated in weekly planning schedules. This article sets out a descriptive retrospective study of day-schedules and driving routes for staff working in home care services. Data were analyzed using GIS. The driving time was between 18% and 26% of working time in municipality A, and between 21% and 23% in municipality B. Visiting time varied between 44% and 62% in municipality A, and 40% and 56% in municipality B. Other tasks, including the legally-required documentation of the care given, varied between 19% and 32% in municipality A and 21% and 38% in municipality B. Overall, 22% of the driving routes in municipality A, and 14% in municipality B, took more time than expected. In municipality A, 22% of the day-schedules underestimated overtime; this figure was 14% in municipality B. In home care services, time taken for driving and to write statutory documentation seems to have been underestimated. Better planning and organization of driving routes would reduce driving time and allow more time for other necessary work.

Modeling the safety impacts of driving hours and rest breaks on truck drivers considering time-dependent covariates.

PubMed

Chen, Chen; Xie, Yuanchang

2014-12-01

Driving hours and rest breaks are closely related to driver fatigue, which is a major contributor to truck crashes. This study investigates the effects of driving hours and rest breaks on commercial truck driver safety. A discrete-time logistic regression model is used to evaluate the crash odds ratios of driving hours and rest breaks. Driving time is divided into 11 one hour intervals. These intervals and rest breaks are modeled as dummy variables. In addition, a Cox proportional hazards regression model with time-dependent covariates is used to assess the transient effects of rest breaks, which consists of a fixed effect and a variable effect. Data collected from two national truckload carriers in 2009 and 2010 are used. The discrete-time logistic regression result indicates that only the crash odds ratio of the 11th driving hour is statistically significant. Taking one, two, and three rest breaks can reduce drivers' crash odds by 68%, 83%, and 85%, respectively, compared to drivers who did not take any rest breaks. The Cox regression result shows clear transient effects for rest breaks. It also suggests that drivers may need some time to adjust themselves to normal driving tasks after a rest break. Overall, the third rest break's safety benefit is very limited based on the results of both models. The findings of this research can help policy makers better understand the impact of driving time and rest breaks and develop more effective rules to improve commercial truck safety. Copyright © 2014 National Safety Council and Elsevier Ltd. All rights reserved.

Nonstationary time series prediction combined with slow feature analysis

NASA Astrophysics Data System (ADS)

Wang, G.; Chen, X.

2015-07-01

Almost all climate time series have some degree of nonstationarity due to external driving forces perturbing the observed system. Therefore, these external driving forces should be taken into account when constructing the climate dynamics. This paper presents a new technique of obtaining the driving forces of a time series from the slow feature analysis (SFA) approach, and then introduces them into a predictive model to predict nonstationary time series. The basic theory of the technique is to consider the driving forces as state variables and to incorporate them into the predictive model. Experiments using a modified logistic time series and winter ozone data in Arosa, Switzerland, were conducted to test the model. The results showed improved prediction skills.

The role of upper torso and pelvis rotation in driving performance during the golf swing.

PubMed

Myers, Joseph; Lephart, Scott; Tsai, Yung-Shen; Sell, Timothy; Smoliga, James; Jolly, John

2008-01-15

While the role of the upper torso and pelvis in driving performance is anecdotally appreciated by golf instructors, their actual biomechanical role is unclear. The aims of this study were to describe upper torso and pelvis rotation and velocity during the golf swing and determine their role in ball velocity. One hundred recreational golfers underwent a biomechanical golf swing analysis using their own driver. Upper torso and pelvic rotation and velocity, and torso-pelvic separation and velocity, were measured for each swing. Ball velocity was assessed with a golf launch monitor. Group differences (groups based on ball velocity) and moderate relationships (r > or = 0.50; P < 0.001) were observed between an increase in ball velocity and the following variables: increased torso-pelvic separation at the top of the swing, maximum torso-pelvic separation, maximum upper torso rotation velocity, upper torso rotational velocity at lead arm parallel and last 40 ms before impact, maximum torso-pelvic separation velocity and torso-pelvic separation velocity at both lead arm parallel and at the last 40 ms before impact. Torso-pelvic separation contributes to greater upper torso rotation velocity and torso-pelvic separation velocity during the downswing, ultimately contributing to greater ball velocity. Golf instructors can consider increasing ball velocity by maximizing separation between the upper torso and pelvis at the top of and initiation of the downswing.

Evolving force balance at Columbia Glacier, Alaska, during its rapid retreat

USGS Publications Warehouse

O'Neel, S.; Pfeffer, W.T.; Krimmel, R.; Meier, M.

2005-01-01

Changes in driving and resistive stresses play an essential role in governing the buoyancy forces that are important controls on the speed and irreversibility of tidewater glacier retreats. We describe changes in geometry, velocity, and strain rate and present a top-down force balance analysis performed over the lower reach of Columbia Glacier. Our analysis uses new measurements and estimates of basal topography and photogrammetric surface velocity measurements made between 1977 and 2001, while assuming depth-independent strain. Sensitivity tests show that the method is robust and insensitive to small changes in the calculation parameters. Spatial distributions of ice speed show little correspondence with driving stress. Instead, spatial patterns of ice speed exhibit a nonlinear correspondence with basal drag. Primary resistance to flow comes from basal drag, but lateral drag becomes increasingly more important throughout the retreat, which may account for observed increases in speed. Maximum basal drag is always located in a prominent constriction located ~12 km upstream from the preretreat terminus. Once the terminus retreated into deep water off the terminal moraine marking the modern maximum extent, the upstream location of this maximum basal drag helped to promote thinning and decrease effective pressure in the lower region by limiting replenishing ice flow from upstream. An increase in both ice velocity and calving resulted, initiating what appears to be an irreversible retreat. Copyright 2005 by the American Geophysical Union.

Experimental Research on Air Propellers III

NASA Technical Reports Server (NTRS)

Durand, W F; Lesley, E P

1920-01-01

Report presents the results of wind tunnel tests of propellers that examined the influence of the following characteristics: (1) nominal pitch ratio 1.3 combined with a certain number of the more common or standard forms and proportions; (2) driving face slightly rounded or convex; (3) change in the location of the maximum thickness ordinate of the blade section; (4) pushing forward the leading edge of the blade, thus giving a rounded convex surface on the leading side of the driving face. (5) a series of values for the constant "angle of attack" in forming propellers with radially increasing pitch. In accordance with these purposes tests were carried out on 28 propellers.

Upper limit for the acceleration gradient in the collinear wake field accelerator as a function of the transformer ratio

DOE PAGES

Baturin, Stanislav; Zholents, A.

2017-06-19

Here, the interrelation between the accelerating gradient and the transformer ratio in the collinear wake field accelerator has been analyzed. It has been shown that the high transformer ratio and the high efficiency of the energy transfer from the drive bunch to the witness bunch can only be achieved at the expense of the accelerating gradient. Rigorous proof is given that in best cases of meticulously shaped charge density distributions in the drive bunch, the maximum accelerating gradient falls proportionally to the gain in the transformer ratio. Conclusions are verified using several representative examples.

Upper limit for the acceleration gradient in the collinear wake field accelerator as a function of the transformer ratio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baturin, Stanislav; Zholents, A.

Here, the interrelation between the accelerating gradient and the transformer ratio in the collinear wake field accelerator has been analyzed. It has been shown that the high transformer ratio and the high efficiency of the energy transfer from the drive bunch to the witness bunch can only be achieved at the expense of the accelerating gradient. Rigorous proof is given that in best cases of meticulously shaped charge density distributions in the drive bunch, the maximum accelerating gradient falls proportionally to the gain in the transformer ratio. Conclusions are verified using several representative examples.

Study on loading and unloading performance of new energy vehicle battery sensor

NASA Astrophysics Data System (ADS)

Wu, Bin; Ren, Kai; Liu, Ying

2017-04-01

This paper first introduces the 18650 battery, describes the importance of the battery temperature sensor, uses Ansys Workbench finite element simulation software and the mean of the combination of displacement constraint and reaction force, studies the force and the size of the change of new energy vehicle battery temperature sensor in the loading, translation and unloading of the three cases, then make the test to verify its accuracy. At last, the test results are compared with the usual maximum acceleration of the vehicle in driving which verified the sensor of the car will not fall off in the car driving process and work normally.

Optical switching property of electromagnetically induced transparency in a Λ system

NASA Astrophysics Data System (ADS)

Zhang, Lianshui; Wang, Jian; Feng, Xiaomin; Yang, Lijun; Li, Xiaoli; Zhao, Min

2008-12-01

In this paper we study the coherent transient property of a Λ-three-level system (Ωd = 0) and a quasi- Λ -four-level system (Ωd>0). Optical switching of the probe field can be achieved by applying a pulsed coupling field or rf field. In Λ -shaped three-level system, when the coupling field was switched on, there is a almost total transparency of the probe field and the time required for the absorption changing from 90% to 10% of the maximum absorption is 2.9Γ0 (Γ0 is spontaneous emission lifetime). When the coupling field was switched off, there is an initial increase of the probe field absorption and then gradually evolves to the maximum of absorption of the two-level absorption, the time required for the absorption of the system changing from 10% to 90% is 4.2Γ0. In four-level system, where rf driving field is used as switching field, to achieve the same depth of the optical switching, the time of the optical switching is 2.5Γ0 and 6.1Γ0, respectively. The results show that with the same depth of the optical switching, the switch-on time of the four-level system is shorter than that of the three-level system, while the switch-off time of the four-level system is longer. The depth of the optical switching of the four-level system was much larger than that of the three-level system, where the depth of the optical switching of the latter is merely 14.8% of that of the former. The speed of optical switching of the two systems can be increased by the increase of Rabi frequency of coupling field or rf field.

MEMS micromirrors for optical switching in multichannel spectrophotometers

NASA Astrophysics Data System (ADS)

Tuantranont, Adisorn; Lomas, Tanom; Bright, Victor M.

2004-04-01

This paper reports for the first time that a novel MEMS-based micromirror switch has successfully demonstrated for optical switching in a multi-channel fiber optics spectrophotometer system. The conventional optomechanical fiber optic switches for multi-channel spectrophotometers available in market are bulky, slow, low numbers of channels and expensive. Our foundry MEMS-based micromirror switch designed for integrating with commercially available spectrophotometers offers more compact devices, increased number of probing channels, higher performance and cheaper. Our MEMS-based micromirror switch is a surface micromachined mirror fabricated through MUMPs foundry. The 280 μm x 280 μm gold coated mirror is suspended by the double-gimbal structure for X and Y axis scanning. Self-assembly by solders is used to elevate the torsion mirror 30 μm over the substrate to achieve large scan angle. The solder self-assembly approach dramatically reduces the time to assembly the switch. The scan mirror is electrostatically controlled by applying voltages. The individual probing signal from each probing head is guided by fibers with collimated lenses and incidents on the center of the mirror. The operating scan angle is in the range of 3.5 degrees with driving voltage of 0-100 V. The fastest switching time of 4 millisecond (1 ms rise time and 3 ms fall time) is measured corresponding to the maximum speed of the mirror of 0.25 kHz when the mirror is scanning at +/- 1.5 degrees. The micromirror switch is packaged with a multi-mode fiber bundle using active alignment technique. A centered fiber is the output fiber that is connected to spectrophotometer. Maximum insertion loss of 5 dB has been obtained. The accuracy of measured spectral data is equivalent to the single channel spectrophotometer with a small degradation on probing signal due to fiber coupling.

Note: Motor-piezoelectricity coupling driven high temperature fatigue device

NASA Astrophysics Data System (ADS)

Ma, Z. C.; Du, X. J.; Zhao, H. W.; Ma, X. X.; Jiang, D. Y.; Liu, Y.; Ren, L. Q.

2018-01-01

The design and performance evaluation of a novel high temperature fatigue device simultaneously driven by servo motor and piezoelectric actuator is our focus. The device integrates monotonic and cyclic loading functions with a maximum tensile load of 1800 N, driving frequency of 50 Hz, alternating load of 95 N, and maximum service temperature of 1200 °C. Multimodal fatigue tests with arbitrary combinations of static and dynamic loads are achieved. At temperatures that range from RT to 1100 °C, the tensile and tensile-fatigue coupling mechanical behaviors of UM Co50 alloys are investigated to verify the feasibility of the device.

On the road performance tests of electric test vehicle for correlation with road load simulator

NASA Technical Reports Server (NTRS)

Dustin, M. O.; Slavik, R. J.

1982-01-01

A dynamometer (road load simulator) is used to test and evaluate electric vehicle propulsion systems. To improve correlation between system tests on the road load simulator and on the road, similar performance tests are conducted using the same vehicle. The results of track tests on the electric propulsion system test vehicle are described. The tests include range at constant speeds and over SAE J227a driving cycles, maximum accelerations, maximum gradability, and tire rolling resistance determination. Road power requirements and energy consumption were also determined from coast down tests.

The concept of a plasma centrifuge with a high frequency rotating magnetic field and axial circulation

NASA Astrophysics Data System (ADS)

Borisevich, V. D.; Potanin, E. P.

2017-07-01

The possibility of using a rotating magnetic field (RMF) in a plasma centrifuge (PC), with axial circulation to multiply the radial separation effect in an axial direction, is considered. For the first time, a traveling magnetic field (TMF) is proposed to drive an axial circulation flow in a PC. The longitudinal separation effect is calculated for a notional model, using specified operational parameters and the properties of a plasma, comprising an isotopic mixture of 20Ne-22Ne and generated by a high frequency discharge. The optimal intensity of a circulation flow, in which the longitudinal separation effect reaches its maximum value, is studied. The optimal parameters of the RMF and TMF for effective separation, as well as the centrifuge performance, are calculated.

Light up-conversion from near-infrared to blue using a photoresponsive organic light-emitting device

NASA Astrophysics Data System (ADS)

Chikamatsu, Masayuki; Ichino, Yoshiro; Takada, Noriyuki; Yoshida, Manabu; Kamata, Toshihide; Yase, Kiyoshi

2002-07-01

A photoresponsive organic light-emitting device combining blue-emitting organic electroluminescent (EL) diode with titanyl phthalocyanine as a near-infrared (IR) sensitive layer was fabricated. By irradiating near-IR light to the device, blue emission occurred in the lower drive voltage (between 5 and 12 V). The result indicates that the device acts as a light switch and/or an up-converter from near-IR light (1.6 eV) to blue (2.6 eV). The EL response times of rise and decay using a near-IR light trigger were 260 and 330 mus, respectively. At a higher voltage (above 12 V), enhancement of blue emission was observed with near-IR light irradiation. The ON/OFF ratio reached a maximum of 103.

The outlook for advanced transport aircraft

NASA Technical Reports Server (NTRS)

Leavens, J. M., Jr.; Schaufele, R. D.; Jones, R. T.; Steiner, J. E.; Beteille, R.; Titcomb, G. A.; Coplin, J. F.; Rowe, B. H.; Lloyd-Jones, D. J.; Overend, W. J.

1982-01-01

The technological advances most likely to contribute to advanced aircraft designs and the efficiency, performance, and financial considerations driving the development directions for new aircraft are reviewed. Fuel-efficiency is perceived as the most critical factor for any new aircraft or component design, with most gains expected to come in areas of propulsion, aerodynamics, configurations, structural designs and materials, active controls, digital avionics, laminar flow control, and air-traffic control improvements. Any component area offers an efficiency improvement of 3-12%, with a maximum of 50% possible with a 4000 m range aircraft. Advanced turboprops have potential applications in short and medium haul subsonic aircraft, while a fuel efficient SST may be possible by the year 2000. Further discussion is devoted to the pivoted oblique wing aircraft, lightweight structures, and the necessity for short payback times.

Prevalence and correlates of drink driving within patrons of Australian night-time entertainment precincts.

PubMed

Curtis, Ashlee; Coomber, Kerri; Hyder, Shannon; Droste, Nic; Pennay, Amy; Jenkinson, Rebecca; Mayshak, Richelle; Miller, Peter G

2016-10-01

Drink driving is a significant public health concern, and contributes to many road fatalities worldwide. The current study is the first to examine the prevalence and correlates of drink driving behavior in a sample of night-time entertainment precinct attendees in Australia. Interviews were conducted with 4214 night-time entertainment precinct attendees in two metropolitan and three regional cities in Australia. Seven correlates of self-reported drink driving were examined: gender, age, occupation, blood alcohol concentration (BAC), alcohol consumed prior to attending a licensed venue, energy drink consumption, and other drug consumption. Fourteen percent of night-time entertainment precinct attendees reported drink driving in the past three months. Bivariate logistic regression models indicated that males were significantly more likely than females to report drink driving in the past three months. Blue-collar workers and sales/clerical/administrative workers were significantly more likely to report drink driving behavior in the past three months than white-collar workers. The likelihood of reporting drink driving during the three months prior to interview significantly increased as BAC on the current night out increased, and when patrons reported engaging in pre-drinking or other drug use. The multivariate model presented a similar pattern of results, however BAC and pre-drinking on the night of the interview were no longer independent significant predictors. Males, blue collar/sales/clerical/administrative workers, and illicit drug consumers were more likely to report engaging in drink driving behavior than their counterparts. Interventions should focus on addressing the considerable proportion night-time entertainment precinct attendees who report engaging in drink driving behavior. Copyright © 2016 Elsevier Ltd. All rights reserved.

Four-cell solar tracker

NASA Technical Reports Server (NTRS)

Berdahl, C. M.

1981-01-01

Forty cm Sun tracker, consisting of optical telescope and four solar cells, stays pointed at Sun throughout day for maximum energy collection. Each solar cell generates voltage proportional to part of solar image it receives; voltages drive servomotors that keep image centered. Mirrored portion of cylinder extends acquisition angle of device by reflecting Sun image back onto solar cells.

Recent Advances in the Development of Ferroelectric Generators

DTIC Science & Technology

2013-06-01

multi FEG- VIG oscillator operating at only 20% maximum voltage (Fig. 4) can generate 10s of kV/m fields at 3 m. The waveform in Fig. 5 was produced...Figure 5. Waveforms produced by a Radiance multi-FEG array driving a VIG (Courtesy of Zachary Roberts, Radiance). This requires large antennas to

A thermo-mechanical correlation with driving forces for hcp martensite and twin formations in the Fe–Mn–C system exhibiting multicomposition sets

PubMed Central

Nakano, Jinichiro

2013-01-01

The thermodynamic properties of the Fe–Mn–C system were investigated by using an analytical model constructed by a CALPHAD approach. The stacking fault energy (SFE) of the fcc structure with respect to the hcp phase was always constant at T0, independent of the composition and temperature when other related parameters were assumed to be constant. Experimental limits for the thermal hcp formation and the mechanical (deformation-induced) hcp formation were separated by the SFE at T0. The driving force for the fcc to hcp transition, defined as a dimensionless value –dGm/(RT), was determined in the presence of Fe-rich and Mn-rich composition sets in each phase. Carbon tended to partition to the Mn-rich phase rather than to the Fe-rich phase for the compositions studied. The results obtained revealed a thermo-mechanical correlation with empirical yield strength, maximum true stress and maximum true strain. The proportionality between thermodynamics and mechanical properties is discussed. PMID:27877555

A thermo-mechanical correlation with driving forces for hcp martensite and twin formations in the Fe–Mn–C system exhibiting multicomposition sets

DOE PAGES

Nakano, Jinichiro

2013-03-15

Thermodynamic properties of the Fe-Mn-C system were investigated by using an analytical model constructed by a CALPHAD approach. Stacking fault energy (SFE) of the fcc structure with respect to the hcp phase was always constant at T 0, independent of composition and temperature when the other related parameters were assumed to be constant. Experimental limits for the thermal hcp formation and the mechanical (deformation-induced) hcp formation were separated by the SFE at T 0. The driving force for the fcc to hcp transition, defined as a dimensionless value –dG m/(RT), was determined in the presence of Fe-rich and Mn-rich compositionmore » sets in each phase. Carbon tended to partition to the Mn-rich phase rather than to the Fe-rich phase for the studied compositions. The obtained results revealed a thermo-mechanical correlation with empirical yield strength, maximum true stress and maximum true strain. The proportionality between thermodynamics and mechanical properties is discussed.« less

Circadian temperature and melatonin rhythms, sleep, and neurobehavioral function in humans living on a 20-h day

NASA Technical Reports Server (NTRS)

Wyatt, J. K.; Ritz-De Cecco, A.; Czeisler, C. A.; Dijk, D. J.

1999-01-01

The interaction of homeostatic and circadian processes in the regulation of waking neurobehavioral functions and sleep was studied in six healthy young subjects. Subjects were scheduled to 15-24 repetitions of a 20-h rest/activity cycle, resulting in desynchrony between the sleep-wake cycle and the circadian rhythms of body temperature and melatonin. The circadian components of cognitive throughput, short-term memory, alertness, psychomotor vigilance, and sleep disruption were at peak levels near the temperature maximum, shortly before melatonin secretion onset. These measures exhibited their circadian nadir at or shortly after the temperature minimum, which in turn was shortly after the melatonin maximum. Neurobehavioral measures showed impairment toward the end of the 13-h 20-min scheduled wake episodes. This wake-dependent deterioration of neurobehavioral functions can be offset by the circadian drive for wakefulness, which peaks in the latter half of the habitual waking day during entrainment. The data demonstrate the exquisite sensitivity of many neurobehavioral functions to circadian phase and the accumulation of homeostatic drive for sleep.

Microclimate and actual evapotranspiration in a humid coastal-plain environment

USGS Publications Warehouse

Dennehy, K.F.; McMahon, P.B.

1987-01-01

Continuous hourly measurements of twelve meteorologic variables recorded during 1983 and 1984 were used to examine the microclimate and actual evapotranspiration at a low-level radioactive-waste burial site near Barnwell, South Carolina. The study area is in the Atlantic Coastal Plain of southwestern South Carolina. Monthly, daily, and hourly trends in net radiation, incoming and reflected short-wave radiation, incoming and emitted long-wave radiation, soil-heat flux, dry- and wet-bulb temperatures, soil temperatures, wind direction and speed, and precipitation were used to characterize the microclimate. Average daily air temperatures ranged from -9 to 32?? Celsius during the period of study. Net radiation varied from about -27 to 251 watts m-2 and was dominated by incoming short-wave radiation throughout the year. The peak net radiation during a summer day generally occurred 2-3h before the peak vapor pressure deficit. In the winter, these peaks occurred at about the same time of day. Monthly precipitation varied from 15 to 241 mm. The Bowen ratio method was used to estimate hourly evapotranspiration, which was summed to also give daily and monthly evapotranspiration. Actual evapotranspiration varied from 0.0 to 0.7 mm h-1, 0.8-5 mm d-1, and 20-140 mm month-1 during 1983 and 1984. The maximum rate of evapotranspiration generally occurred at the same time of day as maximum net radiation, suggesting net radiation was the main driving force for evapotranspiration. Precipitation exceeded evapotranspiration during 14 months of the 2yr study period. Late fall, winter, and early spring contained the majority of these months. The maximum excess precipitation was 115 mm in February 1983. ?? 1987.

Marangoni Effects of a Drop in an Extensional Flow: The Role of Surfactant Physical Chemistry

NASA Technical Reports Server (NTRS)

Stebe, Kathleen J.; Balasubramaniam, R. (Technical Monitor)

2002-01-01

While the changes in stresses caused by surfactant adsorption on non-deforming interfaces have been fairly well established, prior to this work, there were few studies addressing how surfactants alter stresses on strongly deforming interfaces. We chose the model problem of a drop in a uniaxial extensional flow to study these stress conditions To model surfactant effects at fluid interfaces, a proper description of the dependence of the surface tension on surface concentration, the surface equation of state, is required. We have adopted a surface equation of state that accounts for the maximum coverage limit; that is, because surfactants have a finite cross sectional area, there is an upper bound to the amount of surfactant that can adsorb in a monolayer. The surface tension reduces strongly only when this maximum coverage is approached. Since the Marangoni stresses go as the derivative of the surface equation of state times the surface concentration gradient, the non-linear equation of state determines both the effect of surfactants in the normal stress jump, (which is balanced by the product of the mean curvature of the interface times the surface tension), and the tangential stress jump, which is balanced by Marangoni stresses. First, the effects of surface coverage and intermolecular interactions among surfactants which drive aggregation of surfactants in the interface were studied. (see Pawar and Stebe, Physics of Fluids).

A solar cycle dependence of nonlinearity in magnetospheric activity

NASA Astrophysics Data System (ADS)

Johnson, Jay R.; Wing, Simon

2005-04-01

The nonlinear dependencies inherent to the historical Kp data stream (1932-2003) are examined using mutual information and cumulant-based cost as discriminating statistics. The discriminating statistics are compared with surrogate data streams that are constructed using the corrected amplitude adjustment Fourier transform (CAAFT) method and capture the linear properties of the original Kp data. Differences are regularly seen in the discriminating statistics a few years prior to solar minima, while no differences are apparent at the time of solar maxima. These results suggest that the dynamics of the magnetosphere tend to be more linear at solar maximum than at solar minimum. The strong nonlinear dependencies tend to peak on a timescale around 40-50 hours and are statistically significant up to 1 week. Because the solar wind driver variables, VBs, and dynamical pressure exhibit a much shorter decorrelation time for nonlinearities, the results seem to indicate that the nonlinearity is related to internal magnetospheric dynamics. Moreover, the timescales for the nonlinearity seem to be on the same order as that for storm/ring current relaxation. We suggest that the strong solar wind driving that occurs around solar maximum dominates the magnetospheric dynamics, suppressing the internal magnetospheric nonlinearity. On the other hand, in the descending phase of the solar cycle just prior to solar minimum, when magnetospheric activity is weaker, the dynamics exhibit a significant nonlinear internal magnetospheric response that may be related to increased solar wind speed.

The application of multilayer elastic beam in MEMS safe and arming system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Guozhong, E-mail: liguozhong-bit@bit.edu.cn; Shi, Gengchen; Sui, Li

In this paper, a new approach for a multilayer elastic beam to provide a driving force and driving distance for a MEMS safe and arming system is presented. In particular this is applied where a monolayer elastic beam cannot provide adequate driving force and driving distance at the same time in limited space. Compared with thicker elastic beams, the bilayer elastic beam can provide twice the driving force of a monolayer beam to guarantee the MEMS safe and arming systems work reliably without decreasing the driving distance. In this paper, the theoretical analysis, numerical simulation and experimental verification of themore » multilayer elastic beam is presented. The numerical simulation and experimental results show that the bilayer elastic provides 1.8–2 times the driving force of a monolayer, and a method that improves driving force without reducing the driving distance.« less

Do acute myocardial infarction and stroke mortality vary by distance to hospitals in Switzerland? Results from the Swiss National Cohort Study.

PubMed

Berlin, Claudia; Panczak, Radoslaw; Hasler, Rebecca; Zwahlen, Marcel

2016-11-01

Switzerland has mountains and valleys complicating the access to a hospital and critical care in case of emergencies. Treatment success for acute myocardial infarction (AMI) or stroke depends on timely treatment. We examined the relationship between distance to different hospital types and mortality from AMI or stroke in the Swiss National Cohort (SNC) Study. The SNC is a longitudinal mortality study of the census 2000 population of Switzerland. For 4.5 million Swiss residents not living in a nursing home and older than 30 years in the year 2000, we calculated driving time and straight-line distance from their home to the nearest acute, acute with emergency room, central and university hospital (in total 173 hospitals). On the basis of quintiles, we used multivariable Cox proportional hazard models to estimate HRs of AMI and stroke mortality for driving time distance groups compared to the closest distance group. Over 8 years, 19 301 AMI and 21 931 stroke deaths occurred. Mean driving time to the nearest acute hospital was 6.5 min (29.7 min to a university hospital). For AMI mortality, driving time to a university hospital showed the strongest association among the four types of hospitals with a hazard ratio (HR) of 1.19 (95% CI 1.10 to 1.30) and 1.10 (95% CI 1.01 to 1.20) for men and women aged 65+ years when comparing the highest quintile with the lowest quintile of driving time. For stroke mortality, the association with university hospital driving time was less pronounced than for AMI mortality and did not show a clear incremental pattern with increasing driving time. There was no association with driving time to the nearest hospital. The increasing AMI mortality with increasing driving time to the nearest university hospital but not to any nearest hospital reflects a complex interplay of many factors along the care pathway. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Is Distance to Provider a Barrier to Care for Medicaid Patients with Breast, Colorectal, or Lung Cancer?

ERIC Educational Resources Information Center

Scoggins, John F.; Fedorenko, Catherine R.; Donahue, Sara M. A.; Buchwald, Dedra; Blough, David K.; Ramsey, Scott D.

2012-01-01

Purpose: Distance to provider might be an important barrier to timely diagnosis and treatment for cancer patients who qualify for Medicaid coverage. Whether driving time or driving distance is a better indicator of travel burden is also of interest. Methods: Driving distances and times from patient residence to primary care provider were…

EEG alpha spindles and prolonged brake reaction times during auditory distraction in an on-road driving study.

PubMed

Sonnleitner, Andreas; Treder, Matthias Sebastian; Simon, Michael; Willmann, Sven; Ewald, Arne; Buchner, Axel; Schrauf, Michael

2014-01-01

Driver distraction is responsible for a substantial number of traffic accidents. This paper describes the impact of an auditory secondary task on drivers' mental states during a primary driving task. N=20 participants performed the test procedure in a car following task with repeated forced braking on a non-public test track. Performance measures (provoked reaction time to brake lights) and brain activity (EEG alpha spindles) were analyzed to describe distracted drivers. Further, a classification approach was used to investigate whether alpha spindles can predict drivers' mental states. Results show that reaction times and alpha spindle rate increased with time-on-task. Moreover, brake reaction times and alpha spindle rate were significantly higher while driving with auditory secondary task opposed to driving only. In single-trial classification, a combination of spindle parameters yielded a median classification error of about 8% in discriminating the distracted from the alert driving. Reduced driving performance (i.e., prolonged brake reaction times) during increased cognitive load is assumed to be indicated by EEG alpha spindles, enabling the quantification of driver distraction in experiments on public roads without verbally assessing the drivers' mental states. Copyright © 2013 Elsevier Ltd. All rights reserved.

Utah traffic lab driving simulator : user manual and flex lanes scenario development.

DOT National Transportation Integrated Search

2012-06-01

This report describes the University of Utah Traffic Lab (UTL) driving simulator, and a scenario development for Flex Lanes driving simulation. The first part describes the driving simulator in details. At the time of installation, the UTL driving si...

Utah Traffic Lab Driving Simulator : User Manual and Flex Lanes Scenario Development

DOT National Transportation Integrated Search

2012-06-01

This report describes the University of Utah Traffic Lab (UTL) driving simulator, and a scenario development for Flex Lanes driving simulation. The first part describes the driving simulator in details. At the time of installation, the UTL driving si...

Driving performance changes of middle-aged experienced taxi drivers due to distraction tasks during unexpected situations.

PubMed

Kim, Hyung-Sik; Choi, Mi-Hyun; Choi, Jin-Seung; Kim, Hyun-Joo; Hong, Sang-Pyo; Jun, Jae-Hoon; Tack, Gye-Rae; Kim, Boseong; Min, Ung-Chan; Lim, Dae-Woon; Chung, Soon-Cheol

2013-10-01

This study investigated the effects of distraction taskssuch as sending a text message with a cellphone and searching navigation with car navigation system-on the driving performance of 29 highly experienced taxi drivers in their 50s. All participants were instructed to drive using a driving simulator for 2 min. while maintaining a constant distance from the vehicle in front and a constant speed. Participants drove without any distractions for the first minute. For an additional minute, they performed Driving Only or performed a task while driving (Driving + Sending Text Message or Driving + Searching Navigation). An unexpected situation, in which the participant had to stop abruptly due to a sudden stop of the preceding vehicle, occurred during this period. Driving performance during the unexpected situation was evaluated by car control variables, medial-lateral coefficient of variation and brake time, and by motion variables such as the jerk-cost function. Compared to Driving Only, jerk-cost function, medial-lateral coefficient of variation, and brake time increased during Driving + Sending Text Message or Driving + Searching Navigation.

Transportation Energy Futures (TEF) Data and Sources

Science.gov Websites

|agency|4-d|gis|geographic information systems?|municipal|neighborhood|urban density|municipal |carsharing|marketing|real-time|traffic information|eco-driving|idle)$ ^(vmt|vehicle miles traveled|reduction drive|eco-driving|congestion|commute|telework|alternative work|parking|real-time|traffic information

Travel time and attrition from VHA care among women veterans: how far is too far?

PubMed

Friedman, Sarah A; Frayne, Susan M; Berg, Eric; Hamilton, Alison B; Washington, Donna L; Saechao, Fay; Maisel, Natalya C; Lin, Julia Y; Hoggatt, Katherine J; Phibbs, Ciaran S

2015-04-01

Travel time, an access barrier, may contribute to attrition of women veterans from Veterans Health Administration (VHA) care. We examined whether travel time influences attrition: (a) among women veterans overall, (b) among new versus established patients, and (c) among rural versus urban patients. This retrospective cohort study used logistic regression to estimate the association between drive time and attrition, overall and for new/established and rural/urban patients. In total, 266,301 women veteran VHA outpatients in the Fiscal year 2009. An "attriter" did not return for VHA care during the second through third years after her first 2009 visit (T0). Drive time (log minutes) was between the patient's residence and her regular source of VHA care. "New" patients had no VHA visits within 3 years before T0. Models included age, service-connected disability, health status, and utilization as covariates. Overall, longer drive times were associated with higher odds of attrition: drive time adjusted odds ratio=1.11 (99% confidence interval, 1.09-1.14). The relationship between drive time and attrition was stronger among new patients but was not modified by rurality. Attrition among women veterans is sensitive to longer drive time. Linking new patients to VHA services designed to reduce distance barriers (telemedicine, community-based clinics, mobile clinics) may reduce attrition among women new to VHA.

Robust iterative learning contouring controller with disturbance observer for machine tool feed drives.

PubMed

Simba, Kenneth Renny; Bui, Ba Dinh; Msukwa, Mathew Renny; Uchiyama, Naoki

2018-04-01

In feed drive systems, particularly machine tools, a contour error is more significant than the individual axial tracking errors from the view point of enhancing precision in manufacturing and production systems. The contour error must be within the permissible tolerance of given products. In machining complex or sharp-corner products, large contour errors occur mainly owing to discontinuous trajectories and the existence of nonlinear uncertainties. Therefore, it is indispensable to design robust controllers that can enhance the tracking ability of feed drive systems. In this study, an iterative learning contouring controller consisting of a classical Proportional-Derivative (PD) controller and disturbance observer is proposed. The proposed controller was evaluated experimentally by using a typical sharp-corner trajectory, and its performance was compared with that of conventional controllers. The results revealed that the maximum contour error can be reduced by about 37% on average. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

An extended car-following model considering random safety distance with different probabilities

NASA Astrophysics Data System (ADS)

Wang, Jufeng; Sun, Fengxin; Cheng, Rongjun; Ge, Hongxia; Wei, Qi

2018-02-01

Because of the difference in vehicle type or driving skill, the driving strategy is not exactly the same. The driving speeds of the different vehicles may be different for the same headway. Since the optimal velocity function is just determined by the safety distance besides the maximum velocity and headway, an extended car-following model accounting for random safety distance with different probabilities is proposed in this paper. The linear stable condition for this extended traffic model is obtained by using linear stability theory. Numerical simulations are carried out to explore the complex phenomenon resulting from multiple safety distance in the optimal velocity function. The cases of multiple types of safety distances selected with different probabilities are presented. Numerical results show that the traffic flow with multiple safety distances with different probabilities will be more unstable than that with single type of safety distance, and will result in more stop-and-go phenomena.

A small-gap electrostatic micro-actuator for large deflections

PubMed Central

Conrad, Holger; Schenk, Harald; Kaiser, Bert; Langa, Sergiu; Gaudet, Matthieu; Schimmanz, Klaus; Stolz, Michael; Lenz, Miriam

2015-01-01

Common quasi-static electrostatic micro actuators have significant limitations in deflection due to electrode separation and unstable drive regions. State-of-the-art electrostatic actuators achieve maximum deflections of approximately one third of the electrode separation. Large electrode separation and high driving voltages are normally required to achieve large actuator movements. Here we report on an electrostatic actuator class, fabricated in a CMOS-compatible process, which allows high deflections with small electrode separation. The concept presented makes the huge electrostatic forces within nanometre small electrode separation accessible for large deflections. Electrostatic actuations that are larger than the electrode separation were measured. An analytical theory is compared with measurement and simulation results and enables closer understanding of these actuators. The scaling behaviour discussed indicates significant future improvement on actuator deflection. The presented driving concept enables the investigation and development of novel micro systems with a high potential for improved device and system performance. PMID:26655557

Variable-frequency synchronous motor drives for electric vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chalmers, B.J.; Musaba, L.; Gosden, D.F.

1996-07-01

The performance capability envelope of a variable-frequency, permanent-magnet synchronous motor drive with field weakening is dependent upon the product of maximum current and direct-axis inductance. To obtain a performance characteristic suitable for a typical electric vehicle drive, in which short-term increase of current is applied, it is necessary to design an optimum value of direct-axis inductance. The paper presents an analysis of a hybrid motor design which uses a two-part rotor construction comprising a surface-magnet part and an axially laminated reluctance part. This arrangement combines the properties of all other types of synchronous motor and offers a greater choice ofmore » design variables. It is shown that the desired form of performance may be achieved when the high-inductance axis of the reluctance part is arranged to lead the magnet axis by 90{degree} (elec.).« less

Variable-frequency synchronous motor drives for electric vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chalmers, B.J.; Musaba, L.; Gosden, D.F.

1995-12-31

The performance capability envelope of a variable-frequency, permanent-magnet synchronous motor drive with field weakening is dependent upon the product of maximum current and direct-axis inductance. To obtain a performance characteristic suitable for a typical electric vehicle drive, in which short-term increase of current is applied, it is necessary to design an optimum value of direct-axis inductance. The paper presents an analysis of a hybrid motor design which uses a two-part rotor construction comprising a surface-magnet part and an axially-laminated reluctance part. This arrangement combines the properties of all other types of synchronous motor and offers a greater choice of designmore » variables. It is shown that the desired form of performance may be achieved when the high-inductance axis of the reluctance part is arranged to lead the magnet axis by 90{degree} (elec.).« less

A U-shaped linear ultrasonic motor using longitudinal vibration transducers with double feet.

PubMed

Liu, Yingxiang; Liu, Junkao; Chen, Weishan; Shi, Shengjun

2012-05-01

A U-shaped linear ultrasonic motor using longitudinal vibration transducers with double feet was proposed in this paper. The proposed motor contains a horizontal transducer and two vertical transducers. The horizontal transducer includes two exponential shape horns located at the leading ends, and each vertical transducer contains one exponential shape horn. The horns of the horizontal transducer and the vertical transducer intersect at the tip ends where the driving feet are located. Longitudinal vibrations are superimposed in the motor and generate elliptical motions at the driving feet. The two vibration modes of the motor are discussed, and the motion trajectories of driving feet are deduced. By adjusting the structural parameters, the resonance frequencies of two vibration modes were degenerated. A prototype motor was fabricated and measured. Typical output of the prototype is no-load speed of 854 mm/s and maximum thrust force of 40 N at a voltage of 200 V(rms).

Driving: A Road to Unhealthy Lifestyles and Poor Health Outcomes

PubMed Central

Ding, Ding; Gebel, Klaus; Phongsavan, Philayrath; Bauman, Adrian E.; Merom, Dafna

2014-01-01

Background Driving is a common part of modern society, but its potential effects on health are not well understood. Purpose The present cross-sectional study (n = 37,570) examined the associations of driving time with a series of health behaviors and outcomes in a large population sample of middle-aged and older adults using data from the Social, Economic, and Environmental Factor Study conducted in New South Wales, Australia, in 2010. Methods Multiple logistic regression was used in 2013 to examine the associations of usual daily driving time with health-related behaviors (smoking, alcohol use, diet, physical activity, sedentary behavior, sleep) and outcomes (obesity, general health, quality of life, psychological distress, time stress, social functioning), adjusted for socio-demographic characteristics. Results Findings suggested that longer driving time was associated with higher odds for smoking, insufficient physical activity, short sleep, obesity, and worse physical and mental health. The associations consistently showed a dose-response pattern and more than 120 minutes of driving per day had the strongest and most consistent associations with the majority of outcomes. Conclusion This study highlights driving as a potential lifestyle risk factor for public health. More population-level multidisciplinary research is needed to understand the mechanism of how driving affects health. PMID:24911017

Numerical and experimental study of actuator performance on piezoelectric microelectromechanical inkjet print head.

PubMed

Van So, Pham; Jun, Hyun Woo; Lee, Jaichan

2013-12-01

We have investigated the actuator performance of a piezoelectrically actuated inkjet print head via the numerical and experimental analysis. The actuator consisting of multi-layer membranes, such as piezoelectric, elastic and other buffer layers, and ink chamber was fabricated by MEMS processing. The maximum displacement of the actuator membrane obtained in the experiment is explained by numerical analysis. A simulation of the actuator performance with fluidic damping shows that the resonant frequency of the membrane in liquid is reduced from its resonant frequency in air by a factor of three, which was also verified in the experiment. These simulation and experimental studies demonstrate how much "dynamic force," in terms of a membrane's maximum displacement, maximum force and driving frequency, can be produced by an actuator membrane interacting with fluid.

Physics of automated driving in framework of three-phase traffic theory.

PubMed

Kerner, Boris S

2018-04-01

We have revealed physical features of automated driving in the framework of the three-phase traffic theory for which there is no fixed time headway to the preceding vehicle. A comparison with the classical model approach to automated driving for which an automated driving vehicle tries to reach a fixed (desired or "optimal") time headway to the preceding vehicle has been made. It turns out that automated driving in the framework of the three-phase traffic theory can exhibit the following advantages in comparison with the classical model of automated driving: (i) The absence of string instability. (ii) Considerably smaller speed disturbances at road bottlenecks. (iii) Automated driving vehicles based on the three-phase theory can decrease the probability of traffic breakdown at the bottleneck in mixed traffic flow consisting of human driving and automated driving vehicles; on the contrary, even a single automated driving vehicle based on the classical approach can provoke traffic breakdown at the bottleneck in mixed traffic flow.

Physics of automated driving in framework of three-phase traffic theory

NASA Astrophysics Data System (ADS)

Kerner, Boris S.

2018-04-01

We have revealed physical features of automated driving in the framework of the three-phase traffic theory for which there is no fixed time headway to the preceding vehicle. A comparison with the classical model approach to automated driving for which an automated driving vehicle tries to reach a fixed (desired or "optimal") time headway to the preceding vehicle has been made. It turns out that automated driving in the framework of the three-phase traffic theory can exhibit the following advantages in comparison with the classical model of automated driving: (i) The absence of string instability. (ii) Considerably smaller speed disturbances at road bottlenecks. (iii) Automated driving vehicles based on the three-phase theory can decrease the probability of traffic breakdown at the bottleneck in mixed traffic flow consisting of human driving and automated driving vehicles; on the contrary, even a single automated driving vehicle based on the classical approach can provoke traffic breakdown at the bottleneck in mixed traffic flow.

Four quadrant control of induction motors

NASA Technical Reports Server (NTRS)

Hansen, Irving G.

1991-01-01

Induction motors are the nation's workhorse, being the motor of choice in most applications due to their simple rugged construction. It has been estimated that 14 to 27 percent of the country's total electricity use could be saved with adjustable speed drives. Until now, induction motors have not been suited well for variable speed or servo-drives, due to the inherent complexity, size, and inefficiency of their variable speed controls. Work at NASA Lewis Research Center on field oriented control of induction motors using pulse population modulation method holds the promise for the desired drive electronics. The system allows for a variable voltage to frequency ratio which enables the user to operate the motor at maximum efficiency, while having independent control of both the speed and torque of an induction motor in all four quadrants of the speed torque map. Multiple horsepower machine drives were demonstrated, and work is on-going to develop a 20 hp average, 40 hp peak class of machine. The pulse population technique, results to date, and projections for implementation of this existing new motor control technology are discussed.

Inertial piezoelectric linear motor driven by a single-phase harmonic wave with automatic clamping mechanism

NASA Astrophysics Data System (ADS)

He, Liangguo; Chu, Yuheng; Hao, Sai; Zhao, Xiaoyong; Dong, Yuge; Wang, Yong

2018-05-01

A novel, single-phase, harmonic-driven, inertial piezoelectric linear motor using an automatic clamping mechanism was designed, fabricated, and tested to reduce the sliding friction and simplify the drive mechanism and power supply control of the inertial motor. A piezoelectric bimorph and a flexible hinge were connected in series to form the automatic clamping mechanism. The automatic clamping mechanism was used as the driving and clamping elements. A dynamic simulation by Simulink was performed to prove the feasibility of the motor. The finite element method software COMSOL was used to design the structure of the motor. An experimental setup was built to validate the working principle and evaluate the performance of the motor. The prototype motor outputted a no-load velocity of 3.178 mm/s at a voltage of 220 Vp-p and a maximum traction force of 4.25 N under a preload force of 8 N. The minimum resolution of 1.14 μm was achieved at a driving frequency of 74 Hz, a driving voltage of 50 Vp-p, and a preload force of 0 N.

Effect of operating frequency and phase angle on performance of Alpha Stirling cryocooler driven by a novel compact mechanism

NASA Astrophysics Data System (ADS)

Sant, K. D.; Bapat, S. L.

2015-12-01

Amongst the mechanical cryocoolers in use, Stirling cycle cryocoolers exhibit the desirable features such as high efficiency, low specific power consumption, small size and mass and large mean time before failure. Stirling cycle cryocooler of Alpha configuration exhibits better theoretical performance as compared to Gamma. However, the theory could not be put into practice due to unavailability of compatible drive mechanism for Alpha cryocooler providing large stroke to diameter ratio. The concept of novel compact drive mechanism can be made functional to operate miniature Alpha Stirling cryocoolers. It allows the use of multicylinder system while converting rotary motion to reciprocating. This permits the drive mechanism to be employed for driving different configurations of Stirling cryocooler simultaneously. This drive is capable of providing large stroke to diameter ratio compared to other drive mechanisms generally in use for the purpose. A stroke to diameter ratio of three is chosen in the present work and the drive dimensions are calculated for four piston-cylinder arrangements with 90° phase difference between adjacent arrangements providing two Alpha Stirling cryocoolers working simultaneously. It has to be noted that the coolers operate at half the frequency of the motor used. As the two coolers operate at phase difference of 180°, during compression stroke of one unit, the suction stroke occurs for the other unit. Due to power output of second unit, the combined peak torque requirement falls by 26.81% below the peak torque needed when one unit is operated separately. This allows for use of a comparatively lower torque motor. The practicability of the drive ensuring smooth operation of the system is decided based on comparison between torque availability from the motor and torque requirement of the complete unit. The second order method of cyclic (or thermodynamic) analysis provides a simple computational procedure useful for the design of Stirling cryocooler and is adopted for the present theoretical investigations. An appropriate choice of the equations to compute different losses, from available co-relations, is made in accordance with the conditions existing in the present system. The effects of operating frequency and phase angle between compressor and expander pistons are presented in this paper. The cryocooler performance enhances with increase in operating frequency. However, cryocooler operation at 24 Hz (motor operation at 48 Hz) is considered for theoretical performance prediction. The maximum net refrigeration effect as well as COP is available at phase angle of 81° However, it is essential to fix the phase angle at 90° for both the cryocoolers for the positive functioning of drive mechanism.

Effects of a Finger Tapping Fatiguing Task on M1-Intracortical Inhibition and Central Drive to the Muscle.

PubMed

Madrid, Antonio; Madinabeitia-Mancebo, Elena; Cudeiro, Javier; Arias, Pablo

2018-06-19

The central drive to the muscle reduces when muscle force wanes during sustained MVC, and this is generally considered the neurophysiological footprint of central fatigue. The question is if force loss and the failure of central drive to the muscle are responsible mechanisms of fatigue induced by un-resisted repetitive movements. In various experimental blocks, we validated a 3D-printed hand-fixation system permitting the execution of finger-tapping and maximal voluntary contractions (MVC). Subsequently, we checked the suitability of the system to test the level of central drive to the muscle and developed an algorithm to test it at the MVC force plateau. Our main results show that the maximum rate of finger-tapping dropped at 30 s, while the excitability of inhibitory M1-intracortical circuits and corticospinal excitability increased (all by approximately 15%). Furthermore, values obtained immediately after finger-tapping showed that MVC force and the level of central drive to the muscle remained unchanged. Our data suggest that force and central drive to the muscle are not determinants of fatigue induced by short-lasting un-resisted repetitive finger movements, even in the presence of increased inhibition of the motor cortex. According to literature, this profile might be different in longer-lasting, more complex and/or resisted repetitive movements.

Effects of age and the use of hands-free cellular phones on driving behavior and task performance.

PubMed

Liu, Yung-Ching; Ou, Yang-Kun

2011-12-01

This study used a driving simulator to investigate the effect of using a Bluetooth hands-free cellular phone earpiece on the driving behavior of two age groups. Forty-eight participants (24 aged 20-26 and 24 aged 65-73) were examined to assess their performance on the following divided-attention tasks under 2 driving load conditions (high and low): (1) attempting to maintain the speed limit and (2) using a cellular phone while driving. The length of the call conversation (long vs. short) and the conversational content (complex vs. simple) were manipulated as within-subject independent variables. The driving behavior of the participants, their task reaction times and accuracy, and subjective ratings were collected as dependent variables. The results indicate that under low driving loads, short talk times, and simple conversational content, the driving behavior of the participants showed low variance in the vehicle's mean speed. In contrast, complex conversation had a significantly negative impact on driving behavior. Notably, under a low driving load, motorists' driving behaviors, measured in lateral acceleration, caused significantly smaller variance in complex conversations compared to no call and simple conversations. The use of a hands-free cellular phone affected the performance (acceleration, lane deviation, reaction time, and accuracy) of older drivers significantly more than younger drivers. While performing divided attention tasks, the accuracy of the older drivers was 66.3 percent and that of the younger drivers was 96.3 percent. Although this study did not find a clear impact of cellular phone use on the driving behavior of younger drivers, their divided-attention task reaction times and accuracy were better under no-call than calling conditions. This study indicates that the use of hands-free cellular phones could significantly affect the safety of driving among the older and present risks, although lesser, for younger drivers.

iDriving (Intelligent Driving)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malikopoulos, Andreas

2012-09-17

iDriving identifies the driving style factors that have a major impact on fuel economy. An optimization framework is used with the aim of optimizing a driving style with respect to these driving factors. A set of polynomial metamodels is constructed to reflect the responses produced in fuel economy by changing the driving factors. The optimization framework is used to develop a real-time feedback system, including visual instructions, to enable drivers to alter their driving styles in responses to actual driving conditions to improve fuel efficiency.

Distracted Driving in Teens With and Without Attention-Deficit/Hyperactivity Disorder.

PubMed

Stavrinos, Despina; Garner, Annie A; Franklin, Crystal A; Johnson, Haley D; Welburn, Sharon C; Griffin, Russell; Underhill, Andrea T; Fine, Philip R

2015-01-01

This study is among the first to examine the effect of talking on a cell phone or text messaging while driving in teens with and without attention deficit/hyperactivity disorder (ADHD). Teens (average age 17years) with a diagnosis of ADHD (N=16) were matched with typically developing controls (N=18). All participants operated a driving simulator while (1) conversing on a cell phone, (2) text messaging, and (3) with no distraction during a baseline condition. Six indicators of driving performance were recorded: (a) time to complete the drive; (b) lane deviations; (c) variability in lane position (i.e., root mean square [RMS]); (d) reaction time; (e) motor vehicle collisions; and, (f) speed fluctuation. Significantly greater variation in lane position occurred in the texting task compared to no task and the cell phone task. While texting, in particular, teens with ADHD took significantly less time to complete the scenario. No significant main effects of group were found. Generally, those with ADHD did not differ in regard to driving performance, when compared to controls, with the exception of one outcome: time to complete scenario. These findings suggest that distracted driving impairs driving performance of teen drivers, regardless of ADHD status. Texting while driving had the greatest negative impact on driving performance, particularly with regard to variability in lane position (i.e., RMS). This study sheds light on key issues regarding injury prevention, with the intent of providing pediatric care providers with the knowledge to inform teen drivers of risks associated with distracted driving which will ultimately result in reduced rates of motor vehicle crashes and concomitant injuries. Published by Elsevier Inc.

Family members' needs and experiences of driving disruption over time following an acquired brain injury: an evolving issue.

PubMed

Liang, Phyllis; Gustafsson, Louise; Liddle, Jacki; Fleming, Jennifer

2017-07-01

Family members often assume the role of driver for individuals who are not driving post-acquired brain injury (ABI). Given that return to driving can be unpredictable and uncertain, the impact of driving disruption on family members may vary at different stages post-injury. This study aims to understand the needs and experiences of family members over time during driving disruption following an ABI. A qualitative prospective longitudinal research design was used with semi-structured interviews at recruitment to study, 3 and 6 months later. Fourteen family members completed 41 interviews. The longitudinal data revealed four phases of driving disruption: (1) Wait and see, (2) Holding onto a quick fix, (3) No way out, and (4) Resolution and adjustment. The phases described a process of building tension and a need for support and resolution over time. Holding onto a quick fix is a pivotal phase whereby supports, such as engagement in realistic goal setting, are essential to facilitate family members' resolution of driving disruption issues. Family members who see no way out might not actively seek help and these points to a need for long-term and regular follow-ups. Future research can explore ways to support family members at these key times. Implications for rehabilitation Health professionals need to facilitate the process of fostering hope in family members to set realistic expectations of return to driving and the duration of driving disruption. It is necessary to follow-up with family members even years after ABI as the issue of driving disruption could escalate to be a crisis and family members might not actively seek help. Health professionals can consider both practical support for facilitating transport and emotional support when addressing the issue of driving disruption with family members.

Distracted Driving in Teens with and without Attention-Deficit/Hyperactivity Disorder

PubMed Central

Stavrinos, Despina; Garner, Annie A.; Franklin, Crystal A.; Johnson, Haley D.; Welburn, Sharon C.; Griffin, Russell; Underhill, Andrea T.; Fine, Philip R.

2015-01-01

Objective This study is among the first to examine the effect of talking on a cell phone or text messaging while driving in teens with and without Attention Deficit/Hyperactivity Disorder (ADHD). Method Teens (average age 17 years) with a diagnosis of ADHD (N=16) were matched with typically developing controls (N=18). All participants operated a driving simulator while (1) conversing on a cell phone, (2) text messaging, and (3) with no distraction during a baseline condition. Six indicators of driving performance were recorded: (a) time to complete the drive; (b) lane deviations; (c) variability in lane position (i.e., Root Mean Square [RMS]); (d) reaction time; (e) motor vehicle collisions; and, (f) speed fluctuation. Results Significantly greater variation in lane position occurred in the texting task compared to no task and the cell phone task. While texting, in particular, teens with ADHD took significantly less time to complete the scenario. No significant main effects of group were found. Conclusions Generally, those with ADHD did not differ in regard to driving performance, when compared to controls, with the exception of one outcome: time to complete scenario. These findings suggest that distracted driving impairs driving performance of teen drivers, regardless of ADHD status. Texting while driving had the greatest negative impact on driving performance, particularly with regard to variability in lane position (i.e., RMS). This study sheds light on key issues regarding injury prevention, with the intent of providing pediatric care providers with the knowledge to inform teen drivers of risks associated with distracted driving which will ultimately result in reduced rates of motor vehicle crashes and concomitant injuries. PMID:26049214

Bipedal vs. unipedal: a comparison between one-foot and two-foot driving in a driving simulator.

PubMed

Wang, Dong-Yuan Debbie; Richard, F Dan; Cino, Cullen R; Blount, Trevin; Schmuller, Joseph

2017-04-01

Is it better to drive with one foot or with two feet? Although two-foot driving has fostered interminable debate in the media, no scientific and systematic research has assessed this issue and federal and local state governments have provided no answers. The current study compared traditional unipedal (one-foot driving, using the right foot to control the accelerator and the brake pedal) with bipedal (two-foot driving, using the right foot to control the accelerator and the left foot to control the brake pedal) responses to a visual stimulus in a driving simulator study. Each of 30 undergraduate participants drove in a simulated driving scenario. They responded to a STOP sign displayed on the centre of the screen by bringing their vehicle to a complete stop. Brake RT was shorter under the bipedal condition, while throttle RT showed advantage under the unipedal condition. Stopping time and distance showed a bipedal advantage, however. We discuss further limitations of the current study and implications in a driving task. Before drawing any conclusions from the simulator study, further on-road driving tests are necessary to confirm these obtained bipedal advantages. Practitioner Summary: Traditional unipedal (using the right foot to control the accelerator and the brake pedal) with bipedal (using the right foot to control the accelerator and the left foot to control the brake pedal) responses to a visual stimulus in a driving simulator were compared. Our results showed a bipedal advantage. Promotion: Although two-foot driving has fostered interminable debate in the media, no scientific and systematic research has assessed this issue and federal and local state governments have provided no answers. Traditional (one-foot driving, using the right foot to control the accelerator and the brake pedal) with bipedal (using the right foot to control the accelerator and the left foot to control the brake pedal) responses to a visual stimulus in a simulated driving study were compared. Throttle reaction time was faster in the unipedal condition whereas brake reaction time, stopping time and stopping distance showed a bipedal advantage. We discuss further theoretical issues and implications in a driving task.

Variable-Speed Induction Motor Drives for Aircraft Environmental Control Compressors

NASA Technical Reports Server (NTRS)

Mildice, J. W.; Hansen, I. G.; Schreiner, K. E.; Roth, M. E.

1996-01-01

New, more-efficient designs for aircraft jet engines are not capable of supplying the large quantities of bleed air necessary to provide pressurization and air conditioning for the environmental control systems (ECS) of the next generation of large passenger aircraft. System analysis and engineering have determined that electrically-driven ECS can help to maintain the improved fuel efficiencies; and electronic controllers and induction motors are now being developed in a NASA/NPD SBIR Program to drive both types of ECS compressors. Previous variable-speed induction motor/controller system developments and publications have primarily focused on field-oriented control, with large transient reserve power, for maximum acceleration and optimum response in actuator and robotics systems. The application area addressed herein is characterized by slowly-changing inputs and outputs, small reserve power capability for acceleration, and optimization for maximum efficiency. This paper therefore focuses on the differences between this case and the optimum response case, and shows the development of this new motor/controller approach. It starts with the creation of a new set of controller requirements. In response to those requirements, new control algorithms are being developed and implemented in an embedded computer, which is integrated into the motor controller closed loop. Buffered logic outputs are used to drive the power switches in a resonant-technology, power processor/motor-controller, at switching/resonant frequencies high enough to support efficient high-frequency induction motor operation at speeds up to 50,000-RPA

Scaling effects in spiral capsule robots.

PubMed

Liang, Liang; Hu, Rong; Chen, Bai; Tang, Yong; Xu, Yan

2017-04-01

Spiral capsule robots can be applied to human gastrointestinal tracts and blood vessels. Because of significant variations in the sizes of the inner diameters of the intestines as well as blood vessels, this research has been unable to meet the requirements for medical applications. By applying the fluid dynamic equations, using the computational fluid dynamics method, to a robot axial length ranging from 10 -5 to 10 -2  m, the operational performance indicators (axial driving force, load torque, and maximum fluid pressure on the pipe wall) of the spiral capsule robot and the fluid turbulent intensity around the robot spiral surfaces was numerically calculated in a straight rigid pipe filled with fluid. The reasonableness and validity of the calculation method adopted in this study were verified by the consistency of the calculated values by the computational fluid dynamics method and the experimental values from a relevant literature. The results show that the greater the fluid turbulent intensity, the greater the impact of the fluid turbulence on the driving performance of the spiral capsule robot and the higher the energy consumption of the robot. For the same level of size of the robot, the axial driving force, the load torque, and the maximum fluid pressure on the pipe wall of the outer spiral robot were larger than those of the inner spiral robot. For different requirements of the operating environment, we can choose a certain kind of spiral capsule robot. This study provides a theoretical foundation for spiral capsule robots.

Subjective responses of mental workload during real time driving: A pilot field study

NASA Astrophysics Data System (ADS)

Rahman, N. I. A.; Dawal, S. Z. M.; Yusoff, N.

2017-06-01

This study evaluated drivers’ mental workload in real time driving to identify the driving situation’s complexity influences in an attempt to further design on a complete experimental study. Three driving settings were prepared: Session A (simple situation); Session B (moderately complex situation); Session C (very complex situation). To determine the mental workload, the NASA-Task Load Index (TLX) was administered to four drivers after each experimental driving session. The results showed that the Own Performance (OP) was the highest for session A (highway), while Physical Demand (PD) recorded the highest mean workload score across the session B (rural road) and C (city road). Based on the overall results of the study, it can be concluded that the highway is less demanding compared to rural and city road. It can be highlighted in this study that in the rural and city road driving situation, the timing must be set correctly to assure the relevant traffic density. Thus, the sensitivity of the timing must be considered in the future experiment. A larger number of experience drivers must be used in evaluating the driving situations to provide results that can be used to draw more realistic experiments and conclusions.

Response characteristic of high-speed on/off valve with double voltage driving circuit

NASA Astrophysics Data System (ADS)

Li, P. X.; Su, M.; Zhang, D. B.

2017-07-01

High-speed on/off valve, an important part of turbocharging system, its quick response has a direct impact on the turbocharger pressure cycle. The methods of improving the response characteristic of high speed on/off valve include increasing the magnetic force of armature and the voltage, decreasing the mass and current of coil. The less coil number of turns, the solenoid force is smaller. The special armature structure and the magnetic material will raise cost. In this paper a new scheme of double voltage driving circuit is investigated, in which the original driving circuit of high-speed on/off valve is replaced by double voltage driving circuit. The detailed theoretical analysis and simulations were carried out on the double voltage driving circuit, it showed that the switching time and delay time of the valve respectively are 3.3ms, 5.3ms, 1.9ms and 1.8ms. When it is driven by the double voltage driving circuit, the switching time and delay time of this valve are reduced, optimizing its response characteristic. By the comparison related factors (such as duty cycle or working frequency) about influences on response characteristic, the superior of double voltage driving circuit has been further confirmed.

Blue-Enriched White Light Enhances Physiological Arousal But Not Behavioral Performance during Simulated Driving at Early Night

PubMed Central

Rodríguez-Morilla, Beatriz; Madrid, Juan A.; Molina, Enrique; Correa, Angel

2017-01-01

Vigilance usually deteriorates over prolonged driving at non-optimal times of day. Exposure to blue-enriched light has shown to enhance arousal, leading to behavioral benefits in some cognitive tasks. However, the cognitive effects of long-wavelength light have been less studied and its effects on driving performance remained to be addressed. We tested the effects of a blue-enriched white light (BWL) and a long-wavelength orange light (OL) vs. a control condition of dim light on subjective, physiological and behavioral measures at 21:45 h. Neurobehavioral tests included the Karolinska Sleepiness Scale and subjective mood scale, recording of distal-proximal temperature gradient (DPG, as index of physiological arousal), accuracy in simulated driving and reaction time in the auditory psychomotor vigilance task. The results showed that BWL decreased the DPG (reflecting enhanced arousal), while it did not improve reaction time or driving performance. Instead, blue light produced larger driving errors than OL, while performance in OL was stable along time on task. These data suggest that physiological arousal induced by light does not necessarily imply cognitive improvement. Indeed, excessive arousal might deteriorate accuracy in complex tasks requiring precision, such as driving. PMID:28690558

Estimation of lifetime distributions on 1550-nm DFB laser diodes using Monte-Carlo statistic computations

NASA Astrophysics Data System (ADS)

Deshayes, Yannick; Verdier, Frederic; Bechou, Laurent; Tregon, Bernard; Danto, Yves; Laffitte, Dominique; Goudard, Jean Luc

2004-09-01

High performance and high reliability are two of the most important goals driving the penetration of optical transmission into telecommunication systems ranging from 880 nm to 1550 nm. Lifetime prediction defined as the time at which a parameter reaches its maximum acceptable shirt still stays the main result in terms of reliability estimation for a technology. For optoelectronic emissive components, selection tests and life testing are specifically used for reliability evaluation according to Telcordia GR-468 CORE requirements. This approach is based on extrapolation of degradation laws, based on physics of failure and electrical or optical parameters, allowing both strong test time reduction and long-term reliability prediction. Unfortunately, in the case of mature technology, there is a growing complexity to calculate average lifetime and failure rates (FITs) using ageing tests in particular due to extremely low failure rates. For present laser diode technologies, time to failure tend to be 106 hours aged under typical conditions (Popt=10 mW and T=80°C). These ageing tests must be performed on more than 100 components aged during 10000 hours mixing different temperatures and drive current conditions conducting to acceleration factors above 300-400. These conditions are high-cost, time consuming and cannot give a complete distribution of times to failure. A new approach consists in use statistic computations to extrapolate lifetime distribution and failure rates in operating conditions from physical parameters of experimental degradation laws. In this paper, Distributed Feedback single mode laser diodes (DFB-LD) used for 1550 nm telecommunication network working at 2.5 Gbit/s transfer rate are studied. Electrical and optical parameters have been measured before and after ageing tests, performed at constant current, according to Telcordia GR-468 requirements. Cumulative failure rates and lifetime distributions are computed using statistic calculations and equations of drift mechanisms versus time fitted from experimental measurements.

Comparison of hydrodynamic simulations with two-shockwave drive target experiments

NASA Astrophysics Data System (ADS)

Karkhanis, Varad; Ramaprabhu, Praveen; Buttler, William

2015-11-01

We consider hydrodynamic continuum simulations to mimic ejecta generation in two-shockwave target experiments, where metallic surface is loaded by two successive shock waves. Time of second shock in simulations is determined to match experimental amplitudes at the arrival of the second shock. The negative Atwood number A --> - 1 of ejecta simulations leads to two successive phase inversions of the interface corresponding to the passage of the shocks from heavy to light media in each instance. Metallic phase of ejecta (solid/liquid) depends on shock loading pressure in the experiment, and we find that hydrodynamic simulations quantify the liquid phase ejecta physics with a fair degree of accuracy, where RM instability is not suppressed by the strength effect. In particular, we find that our results of free surface velocity, maximum ejecta velocity, and maximum ejecta areal density are in excellent agreement with their experimental counterparts, as well as ejecta models. We also comment on the parametric space for hydrodynamic simulations in which they can be used to compare with the target experiments. This work was supported in part by the (U.S.) Department of Energy (DOE) under Contract No. DE-AC52-06NA2-5396.

On the rejection of internal and external disturbances in a wind energy conversion system with direct-driven PMSG.

PubMed

Li, Shengquan; Zhang, Kezhao; Li, Juan; Liu, Chao

2016-03-01

This paper deals with the critical issue in a wind energy conversion system (WECS) based on a direct-driven permanent magnet synchronous generator (PMSG): the rejection of lumped disturbance, including the system uncertainties in the internal dynamics and unknown external forces. To simultaneously track the motor speed in real time and capture the maximum power, a maximum power point tracking strategy is proposed based on active disturbance rejection control (ADRC) theory. In real application, system inertia, drive torque and some other parameters change in a wide range with the variations of disturbances and wind speeds, which substantially degrade the performance of WECS. The ADRC design must incorporate the available model information into an extended state observer (ESO) to compensate the lumped disturbance efficiently. Based on this principle, a model-compensation ADRC is proposed in this paper. Simulation study is conducted to evaluate the performance of the proposed control strategy. It is shown that the effect of lumped disturbance is compensated in a more effective way compared with the traditional ADRC approach. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Friesen, Brian; Baron, E.; Parrent, Jerod T.

This paper presents optical spectra of the nearby Type Ia supernova SN 2011fe at 100, 205, 311, 349 and 578 d post-maximum light, as well as an ultraviolet (UV) spectrum obtained with the Hubble Space Telescope at 360 d post-maximum light. We compare these observations with synthetic spectra produced with the radiative transfer code PHOENIX. The day +100 spectrum can be well fitted with models that neglect collisional and radiative data for forbidden lines. Curiously, including these data and recomputing the fit yields a quite similar spectrum, but with different combinations of lines forming some of the stronger features. Atmore » day +205 and later epochs, forbidden lines dominate much of the optical spectrum formation; however, our results indicate that recombination, not collisional excitation, is the most influential physical process driving spectrum formation at these late times. Consequently, our synthetic optical and UV spectra at all epochs presented here are formed almost exclusively through recombinationdriven fluorescence. Furthermore, our models suggest that the UV spectrum even as late as day +360 is optically thick and consists of permitted lines from several iron-peak species. These results indicate that the transition to the 'nebular' phase in Type Ia supernovae is complex and highly wavelength dependent.« less

Impaired alertness and performance driving home from the night shift: a driving simulator study.

PubMed

Akerstedt, Torbjörn; Peters, Björn; Anund, Anna; Kecklund, Göran

2005-03-01

Driving in the early morning is associated with increased accident risk affecting not only professional drivers but also those who commute to work. The present study used a driving simulator to investigate the effects of driving home from a night shift. Ten shift workers participated after a normal night shift and after a normal night sleep. The results showed that driving home from the night shift was associated with an increased number of incidents (two wheels outside the lane marking, from 2.4 to 7.6 times), decreased time to first accident, increased lateral deviation (from 18 to 43 cm), increased eye closure duration (0.102 to 0.143 s), and increased subjective sleepiness. The results indicate severe postnight shift effects on sleepiness and driving performance.

Trap-assisted hole injection and quantum efficiency enhancement in poly(9,9' dioctylfluorene-alt-benzothiadiazole) polymer light-emitting diodes

NASA Astrophysics Data System (ADS)

Seeley, Alexander J. A. B.; Friend, Richard H.; Kim, Ji-Seon; Burroughes, Jeremy H.

2004-12-01

We report a reversible many-fold quantum efficiency enhancement during electrical driving of polymer light-emitting diodes (LEDs) containing poly(9,9' dioctylfluorene-alt-benzothiadiazole) (F8BT), developing over several minutes or hours at low applied bias and recovering on similar time scales after driving. This phenomenon is observed only in devices containing F8BT as an emissive layer in pure or blended form, regardless of anode and cathode choices and even in the absence of a poly(styrene-sulphonate)-doped poly(3,4-ethylene-dioxythiophene) (PEDOT:PSS) layer. We report detailed investigations using a standardized device structure containing PEDOT:PSS and a calcium cathode. Direct measurements of trapped charge recovered from the device after driving significantly exceed the unipolar limit, and thermally activated relaxation suggests a maximum trap depth around 0.6eV. Neither photoluminescence nor electroluminescence spectra reveal any change in the bulk optoelectronic properties of the emissive polymer nor any new emissive species. During the quantum efficiency (QE) enhancement process, the bulk conduction of the device increases. Reverse bias treatment of the device significantly reinforces the QE enhancement. Based on these observations, we propose a simple model in which interfacial dipoles are generated by trapped holes near the anode combining with injected electrons, to produce a narrow tunneling barrier for easy hole injection. The new injection pathway leads to a higher hole current density and thus a better charge injection balance. This produces the relatively high quantum efficiency observed in all F8BT LEDs.

The Dual Role of Starbursts and Active Galactic Nuclei in Driving Extreme Molecular Outflows

NASA Astrophysics Data System (ADS)

Gowardhan, Avani; Spoon, Henrik; Riechers, Dominik A.; González-Alfonso, Eduardo; Farrah, Duncan; Fischer, Jacqueline; Darling, Jeremy; Fergulio, Chiara; Afonso, Jose; Bizzocchi, Luca

2018-05-01

We report molecular gas observations of IRAS 20100‑4156 and IRAS 03158+4227, two local ultraluminous infrared galaxies (ULIRGs) hosting some of the fastest and most massive molecular outflows known. Using Atacama Large Millimeter Array and Plateau de Bure Interferometer observations, we spatially resolve the CO (1‑0) emission from the outflowing molecular gas in both and find maximum outflow velocities of v max ∼ 1600 and ∼1700 km s‑1 for IRAS 20100‑4156 and IRAS 03158+4227, respectively. We find total gas mass outflow rates of {\\dot{M}}OF}∼ 670 and ∼350 M ⊙ yr‑1, respectively, corresponding to molecular gas depletion timescales {τ }OF}dep}∼ 11 and ∼16 Myr. This is nearly 3 times shorter than the depletion timescales implied by star formation, {τ }SFR}dep}∼ 33 and ∼46 Myr, respectively. To determine the outflow driving mechanism, we compare the starburst luminosity (L *) and active galactic nucleus (AGN) luminosity (L AGN) to the outflowing energy and momentum fluxes, using mid-infrared spectral decomposition to discern L AGN. Comparison to other molecular outflows in ULIRGs reveals that outflow properties correlate similarly with L * and L IR as with L AGN, indicating that AGN luminosity alone may not be a good tracer of feedback strength and that a combination of AGN and starburst activity may be driving the most powerful molecular outflows. We also detect the OH 1.667 GHz maser line from both sources and demonstrate its utility in detecting molecular outflows.

Ambulatory heart rate of professional taxi drivers while driving without their typical psychosocial work stressors: a pilot study.

PubMed

Choi, BongKyoo; Choi, SangJun; Jeong, JeeYeon; Lee, JiWon; Shu, Shi; Yu, Nu; Ko, SangBaek; Zhu, Yifang

2016-01-01

Few studies have examined ambulatory cardiovascular physiological parameters of taxi drivers while driving in relation to their occupational hazards. This study aims to investigate and quantify the impact of worksite physical hazards as a whole on ambulatory heart rate of professional taxi drivers while driving without their typical worksite psychosocial stressors. Ambulatory heart rate (HR driving ) of 13 non-smoking male taxi drivers (24 to 67 years old) while driving was continuously assessed on their 6-hour experimental on-road driving in Los Angeles. Percent maximum HR range (PMHR driving ) of the drivers while driving was estimated based on the individual HR driving values and US adult population resting HR (HR rest ) reference data. For analyses, the HR driving and PMHR driving data were split and averaged into 5-min segments. Five physical hazards inside taxi cabs were also monitored while driving. Work stress and work hours on typical work days were self-reported. The means of the ambulatory 5-min HR driving and PMHR driving values of the 13 drivers were 80.5 bpm (11.2 bpm higher than their mean HR rest ) and 10.7 % (range, 5.7 to 19.9 %), respectively. The means were lower than the upper limits of ambulatory HR and PMHR for a sustainable 8-hour work (35 bpm above HR rest and 30 % PMHR), although 15-27 % of the 5-min HR driving and PMHR driving values of one driver were higher than the limits. The levels of the five physical hazards among the drivers were modest: temperature (26.4 ± 3.0 °C), relative humidity (40.7 ± 10.4 %), PM 2.5 (21.5 ± 7.9  μg /m 3 ), CO 2 (1,267.1 ± 580.0 ppm) and noise (69.7 ± 3.0 dBA). The drivers worked, on average, 72 h per week and more than half of them reported that their job were often stressful. The impact of physical worksite hazards alone on ambulatory HR of professional taxi drivers in Los Angeles generally appeared to be minor. Future ambulatory heart rate studies including both physical and psychosocial hazards of professional taxi drivers are warranted.

Nonspherical dynamics and shape mode stability of ultrasound contrast agent microbubbles

NASA Astrophysics Data System (ADS)

Calvisi, Michael

2016-11-01

Ultrasound contrast agents (UCAs) are shell encapsulated microbubbles developed originally for ultrasound imaging enhancement. UCAs are more recently being exploited for therapeutic applications, such as for drug delivery, gene therapy, and tissue ablation. Ultrasound transducer pulses can induce spherical (radial) UCA oscillations, translation, and nonspherical shape oscillations, the dynamics of which are highly coupled. If driven sufficiently strongly, the ultrasound can induce breakup of UCAs, which can facilitate drug or gene delivery but should be minimized for imaging purposes to increase residence time and maximize diagnostic effect. Therefore, an understanding of the interplay between the acoustic driving and nonspherical shape mode stability of UCAs is essential for both diagnostic and therapeutic applications. In this work, we use both analytical and numerical methods to analyze shape mode stability for cases of small and large nonspherical oscillations, respectively. To analyze shape mode stability in the limit of small nonspherical perturbations, we couple a radial model of a lipid-coated microbubble with a model for bubble translation and nonspherical shape oscillation. This hybrid model is used to predict shape mode stability for ultrasound driving frequencies and pressure amplitudes of clinical interest. In addition, calculations of the stability of individual shape modes, residence time, maximum radius, and translation are provided with respect to acoustic driving parameters and compared to an unshelled bubble. The effects of shell elasticity, shell viscosity, and initial radius on stability are investigated. Furthermore, the well-established boundary element method (BEM) is used to investigate the dynamics and shape stability of large amplitude nonspherical oscillations of an ultrasonically-forced, polymer-coated microbubble near a rigid boundary. Different instability modes are identified based on the degree of jetting and proximity to the boundary. This insight is used to develop diagrams that delineate regions of stability from instability based on the breakup mechanism, in parameter ranges of ultrasound frequency and amplitude relevant to medical applications.

Factors influencing quality of patient interaction at community pharmacy drive-through and walk-in counselling areas.

PubMed

Odukoya, Olufunmilola K; Chui, Michelle A; Pu, Jia

2014-08-01

To examine factors influencing the amount of time and information pharmacy personnel provide to patients at drive-through and walk-in counselling areas. On-site observational data collection in 22 community pharmacies by pharmacy students. Information included observable patient characteristics such as gender, age range, English proficiency and mobility impairment; encounter characteristics included type of prescription and whether the patient was acknowledged; and counselling characteristics included types of counselling information conveyed and length of time for each encounter. Patient-pharmacist encounters were documented at the drive-through and walk-in counselling areas 961 and 1098 times respectively. Pharmacists spent less time, and technicians more time, with patients at the drive-through counselling area. The amount of information provided to patients was significantly affected by whether the patient was receiving new versus refill prescriptions. Patients with a new prescription were twice as likely to receive more information from pharmacy personnel. There was a significant difference between the amount of counselling provided to patients at the drive-through and walk-in counselling area (rate ratio (RR) 0.92, 95% confidence interval (CI): 0.86-1.00). Patients at the drive-through received a lower amount of information relative to patients using the walk-in. Amount of information provided to patients was affected by the level of pharmacy busyness (RR 0.96, 95% CI: 0.95-0.99). Providing patient care at the drive-through counselling area may negatively influence quality of patient care. To improve quality of pharmacy drive-through services, standardization of drive-through services in pharmacies may be needed. © 2013 Royal Pharmaceutical Society.

The Attentional Demand of Automobile Driving Revisited: Occlusion Distance as a Function of Task-Relevant Event Density in Realistic Driving Scenarios.

PubMed

Kujala, Tuomo; Mäkelä, Jakke; Kotilainen, Ilkka; Tokkonen, Timo

2016-02-01

We studied the utility of occlusion distance as a function of task-relevant event density in realistic traffic scenarios with self-controlled speed. The visual occlusion technique is an established method for assessing visual demands of driving. However, occlusion time is not a highly informative measure of environmental task-relevant event density in self-paced driving scenarios because it partials out the effects of changes in driving speed. Self-determined occlusion times and distances of 97 drivers with varying backgrounds were analyzed in driving scenarios simulating real Finnish suburban and highway traffic environments with self-determined vehicle speed. Occlusion distances varied systematically with the expected environmental demands of the manipulated driving scenarios whereas the distributions of occlusion times remained more static across the scenarios. Systematic individual differences in the preferred occlusion distances were observed. More experienced drivers achieved better lane-keeping accuracy than inexperienced drivers with similar occlusion distances; however, driving experience was unexpectedly not a major factor for the preferred occlusion distances. Occlusion distance seems to be an informative measure for assessing task-relevant event density in realistic traffic scenarios with self-controlled speed. Occlusion time measures the visual demand of driving as the task-relevant event rate in time intervals, whereas occlusion distance measures the experienced task-relevant event density in distance intervals. The findings can be utilized in context-aware distraction mitigation systems, human-automated vehicle interaction, road speed prediction and design, as well as in the testing of visual in-vehicle tasks for inappropriate in-vehicle glancing behaviors in any dynamic traffic scenario for which appropriate individual occlusion distances can be defined. © 2015, Human Factors and Ergonomics Society.

A High-resolution Model of Field-aligned Currents Through Empirical Orthogonal Functions Analysis (MFACE)

NASA Technical Reports Server (NTRS)

He, Maosheng; Vogt, Joachim; Luehr, Hermann; Sorbalo, Eugen; Blagau, Adrian; Le, Guan; Lu, Gang

2012-01-01

Ten years of CHAMP magnetic field measurements are integrated into MFACE, a model of field-aligned currents (FACs) using empirical orthogonal functions (EOFs). EOF1 gives the basic Region-1/Region-2 pattern varying mainly with the interplanetary magnetic field Bz component. EOF2 captures separately the cusp current signature and By-related variability. Compared to existing models, MFACE yields significantly better spatial resolution, reproduces typically observed FAC thickness and intensity, improves on the magnetic local time (MLT) distribution, and gives the seasonal dependence of FAC latitudes and the NBZ current signature. MFACE further reveals systematic dependences on By, including 1) Region-1/Region-2 topology modifications around noon; 2) imbalance between upward and downward maximum current density; 3) MLT location of the Harang discontinuity. Furthermore, our procedure allows quantifying response times of FACs to solar wind driving at the bow shock nose: we obtain 20 minutes and 35-40 minutes lags for the FAC density and latitude, respectively.

Traffic crash accidents in Tehran, Iran: Its relation with circadian rhythm of sleepiness.

PubMed

Sadeghniiat-Haghighi, Khosro; Yazdi, Zohreh; Moradinia, Mohsen; Aminian, Omid; Esmaili, Alireza

2015-01-01

Road traffic accidents are one of main problems in Iran. Multiple factors cause traffic accidents and the most important one is sleepiness. This factor, however, is given less attention in our country. Road traffic accidents relevant to sleepiness are studied. In this cross-sectional study, all road traffic accidents relevant to sleepiness, which were reported by police, were studied in Tehran province in 2009. The risk of road traffic accidents due to sleepiness was increased by more than sevenfold (odds ratio = 7.33) in low alertness hours (0:00-6:00) compared to other time of day. The risk of road traffic accidents due to sleepiness was decreased by 0.15-fold (odds ratio = 0.15) in hours with maximum of alertness (18:00-22:00) of circadian rhythm compared to other time of day. The occurrence of road traffic accidents due to sleepiness has significant statistical relations with driving during lowest point of alertness of circadian rhythm.

Soft x-ray tomography for real-time applications: present status at Tore Supra and possible future developments.

PubMed

Mazon, D; Vezinet, D; Pacella, D; Moreau, D; Gabelieri, L; Romano, A; Malard, P; Mlynar, J; Masset, R; Lotte, P

2012-06-01

This paper is focused on the soft x-ray (SXR) tomography system setup at Tore Supra (DTOMOX) and the recent developments made to automatically get precise information about plasma features from inverted data. The first part describes the main aspects of the tomographic inversion optimization process. Several observations are made using this new tool and a set of shape factors is defined to help characterizing the emissivity field in a real-time perspective. The second part presents a detailed off-line analysis comparing the positions of the magnetic axis obtained from a magnetic equilibrium solver, and the maximum of the reconstructed emissivity field for ohmic and heated pulses. A systematic discrepancy of about 5 cm is found in both cases and it is shown that this discrepancy increases during sawtooth crashes. Finally, evidence of radially localized tungsten accumulation with an in-out asymmetry during a lower hybrid current drive pulse is provided to illustrate the DTOMOX capabilities for a precise observation of local phenomena.

Finite-time hybrid projective synchronization of the drive-response complex networks with distributed-delay via adaptive intermittent control

NASA Astrophysics Data System (ADS)

Cheng, Lin; Yang, Yongqing; Li, Li; Sui, Xin

2018-06-01

This paper studies the finite-time hybrid projective synchronization of the drive-response complex networks. In the model, general transmission delays and distributed delays are also considered. By designing the adaptive intermittent controllers, the response network can achieve hybrid projective synchronization with the drive system in finite time. Based on finite-time stability theory and several differential inequalities, some simple finite-time hybrid projective synchronization criteria are derived. Two numerical examples are given to illustrate the effectiveness of the proposed method.

Discontinuous precipitation in a Cd-6 at.% Ag alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Manna, I.; Bala, P.K.; Pabi, S.K.

1996-11-01

Discontinuous precipitation (DP) in a Cd-6 at.% Ag alloy has been investigated for the first time. The precipitate phase maintains a lamellar morphology and statistically constant interlamellar spacing under a given isothermal condition in the temperature range studied (333--523 K). The interlamellar spacing increases with an increase in isothermal temperature. The reaction front velocity registers a typical C-curve variation with the inverse of temperature. The reaction rate is maximum at 470 K. The predicted upper limit of DP occurrence in this alloy is 23 K lower than the concerned equilibrium solvus temperature. Continuous precipitation accompanies DP at all temperatures, especiallymore » beyond a certain time, and adversely affects the growth kinetics of DP colonies by reducing the local chemical driving force and/or posing physical hindrance to the reaction front migration. An extensive kinetic analysis of DP using the models by Turnbull, Aaronson and Liu, and Petermann and Hornbogen has yielded the grain boundary chemical diffusivity data in Cd-6 At.% Ag for the first time, the activation energy of which lies in the range 55--77 kJ/mol.« less

Good distractions: Testing the effects of listening to an audiobook on driving performance in simple and complex road environments.

PubMed

Nowosielski, Robert J; Trick, Lana M; Toxopeus, Ryan

2018-02-01

Distracted driving (driving while performing a secondary task) causes many collisions. Most research on distracted driving has focused on operating a cell-phone, but distracted driving can include eating while driving, conversing with passengers or listening to music or audiobooks. Although the research has focused on the deleterious effects of distraction, there may be situations where distraction improves driving performance. Fatigue and boredom are also associated with collision risk and it is possible that secondary tasks can help alleviate the effects of fatigue and boredom. Furthermore, it has been found that individuals with high levels of executive functioning as measured by the OSPAN (Operation Span) task show better driving while multitasking. In this study, licensed drivers were tested in a driving simulator (a car body surrounded by screens) that simulated simple or complex roads. Road complexity was manipulated by increasing traffic, scenery, and the number of curves in the drive. Participants either drove, or drove while listening to an audiobook. Driving performance was measured in terms of braking response time to hazards (HRT): the time required to brake in response to pedestrians or vehicles that suddenly emerged from the periphery into the path of the vehicle, speed, standard deviation of speed, standard deviation of lateral position (SDLP). Overall, braking times to hazards were higher on the complex drive than the simple one, though the effects of secondary tasks such as audiobooks were especially deleterious on the complex drive. In contrast, on the simple drive, driving while listening to an audiobook lead to faster HRT. We found evidence that individuals with high OSPAN scores had faster HRTs when listening to an audiobook. These results suggest that there are environmental and individual factors behind difference in the allocation of attention while listening to audiobooks while driving. Copyright © 2017 Elsevier Ltd. All rights reserved.

Software and hardware complex for research and management of the separation process

NASA Astrophysics Data System (ADS)

Borisov, A. P.

2018-01-01

The article is devoted to the development of a program for studying the operation of an asynchronous electric drive using vector-algorithmic switching of windings, as well as the development of a hardware-software complex for controlling parameters and controlling the speed of rotation of an asynchronous electric drive for investigating the operation of a cyclone. To study the operation of an asynchronous electric drive, a method was used in which the average value of flux linkage is found and a method for vector-algorithmic calculation of the power and electromagnetic moment of an asynchronous electric drive feeding from a single-phase network is developed, with vector-algorithmic commutation, and software for calculating parameters. The software part of the complex allows to regulate the speed of rotation of the motor by vector-algorithmic switching of transistors or, using pulse-width modulation (PWM), set any engine speed. Also sensors are connected to the hardware-software complex at the inlet and outlet of the cyclone. The developed cyclone with an inserted complex allows to receive high efficiency of product separation at various entrance speeds. At an inlet air speed of 18 m / s, the cyclone’s maximum efficiency is achieved. For this, it is necessary to provide the rotational speed of an asynchronous electric drive with a frequency of 45 Hz.

Alternative Fuels Data Center: Strategies for Fleet Managers to Conserve

Science.gov Websites

example, is often required for all drivers. Some corporate policies specify maximum driving speeds for lists of equipment or set limitations on the amount of cargo carried in a vehicle. For example, to vehicles needed for routes. For example, fleets may make certain high-traffic routes off limits during

A Biological Model for Directional Sensing of Seismic Vibration

DTIC Science & Technology

2002-02-25

the 100-200 Hz range, with some energy present up to 4 kHz). We place an insect in the center of the dowel where, because of its sedentary ... lifestyle , it will usually remain for an extended period (up to 30 min or more). We then drive the simulator with a random noise signal (maximum frequency

49 CFR 571.126 - Standard No. 126; Electronic stability control systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... driver on the previous ignition cycle that is designed for low-speed, off-road driving, or (b) the... is designed for operation at higher speeds on snow-, sand-, or dirt-packed roads and that has the... dealer, fully fueled, with a 73 kg (160 lb) driver. Standard outriggers shall be designed with a maximum...

And never the twain shall meet? Integrating revenue cycle and supply chain functions.

PubMed

Matjucha, Karen A; Chung, Bianca

2008-09-01

Four initial steps to implementing a profit and loss management model are: Identify the supplies clinicians are using. Empower stakeholders to remove items that are not commonly used. Reduce factors driving wasted product. Review the chargemaster to ensure that supplies used in selected procedures are represented. Strategically set prices that optimize maximum allowable reimbursement.

Naturalistic Teenage Driving Study: Findings and Lessons Learned

PubMed Central

Simons-Morton, Bruce G.; Klauer, Sheila G.; Ouimet, Marie Claude; Guo, Feng; Albert, Paul S.; Lee, Suzanne E.; Ehsani, Johnathon P.; Pradhan, Anuj K.; Dingus, Thomas A.

2015-01-01

Problem This paper summarizes the findings on novice teenage driving outcomes (e.g., crashes and risky driving behaviors) from the Naturalistic Teenage Driving Study. Method Survey and driving data from a data acquisition system (Global Positioning System, accelerometers, cameras) were collected from 42 newly-licensed teenage drivers and their parents during the first 18 months of teenage licensure; stress responsivity was also measured in teenagers. Result Overall teenage crash and near crash (CNC) rates declined over time, but were >4 times higher among teenagers than adults. Contributing factors to teenage CNC rates included secondary task engagement (e.g., distraction), kinematic risky driving, low stress responsivity, and risky social norms. Conclusion The data support the contention that the high novice teenage CNC risk is due both to inexperience and risky driving behavior, particularly kinematic risky driving and secondary task engagement. Practical Applications Graduated driver licensing policy and other prevention efforts should focus on kinematic risky driving, secondary task engagement, and risky social norms. PMID:26403899

Driving performance in persons with mild to moderate symptoms of multiple sclerosis.

PubMed

Devos, Hannes; Brijs, Tom; Alders, Geert; Wets, Geert; Feys, Peter

2013-08-01

To investigate whether driving performance is impaired in persons with mild to moderate multiple sclerosis (MS). This study included 15 persons with MS (pwMS) and 17 healthy controls. The MS group exhibited mild to moderate impairments on the Expanded Disability Status Scale (median, Q1-Q3; 3.5, 2.5-4). The driving simulation required participants to drive in daily traffic while attending to a divided attention (DA) task. Computerized measures on the driving task included number of accidents, tickets, speed maintenance, standard deviation of lateral position, and time to collision. Response times and accuracy on the DA task were also computer generated. Additionally, pwMS completed a clinical evaluation encompassing motor, functional, visual, psychosocial and cognitive tests. No differences between healthy controls and pwMS were observed on all measures of the primary driving task. PwMS performed worse than healthy controls on DA response time (3.10 s, 2.87-3.68 versus 2.15 s, 2.04-2.43; p = 0.001) and accuracy (15 correct answers, 11-18 versus 24 correct answers, 22-25; p < 0.0001). Depression was significantly associated with time to collision (r = -0.77; p < 0.01). Subjects with mild to moderate MS are able to prioritize the driving task above the DA task. The relationship between depression and driving performance in MS merits further investigation.

A spectral power analysis of driving behavior changes during the transition from nondistraction to distraction.

PubMed

Wang, Yuan; Bao, Shan; Du, Wenjun; Ye, Zhirui; Sayer, James R

2017-11-17

This article investigated and compared frequency domain and time domain characteristics of drivers' behaviors before and after the start of distracted driving. Data from an existing naturalistic driving study were used. Fast Fourier transform (FFT) was applied for the frequency domain analysis to explore drivers' behavior pattern changes between nondistracted (prestarting of visual-manual task) and distracted (poststarting of visual-manual task) driving periods. Average relative spectral power in a low frequency range (0-0.5 Hz) and the standard deviation in a 10-s time window of vehicle control variables (i.e., lane offset, yaw rate, and acceleration) were calculated and further compared. Sensitivity analyses were also applied to examine the reliability of the time and frequency domain analyses. Results of the mixed model analyses from the time and frequency domain analyses all showed significant degradation in lateral control performance after engaging in visual-manual tasks while driving. Results of the sensitivity analyses suggested that the frequency domain analysis was less sensitive to the frequency bandwidth, whereas the time domain analysis was more sensitive to the time intervals selected for variation calculations. Different time interval selections can result in significantly different standard deviation values, whereas average spectral power analysis on yaw rate in both low and high frequency bandwidths showed consistent results, that higher variation values were observed during distracted driving when compared to nondistracted driving. This study suggests that driver state detection needs to consider the behavior changes during the prestarting periods, instead of only focusing on periods with physical presence of distraction, such as cell phone use. Lateral control measures can be a better indicator of distraction detection than longitudinal controls. In addition, frequency domain analyses proved to be a more robust and consistent method in assessing driving performance compared to time domain analyses.

Abdicating power for control: a precision timing strategy to modulate function of flight power muscles.

PubMed

Sponberg, S; Daniel, T L

2012-10-07

Muscles driving rhythmic locomotion typically show strong dependence of power on the timing or phase of activation. This is particularly true in insects' main flight muscles, canonical examples of muscles thought to have a dedicated power function. However, in the moth (Manduca sexta), these muscles normally activate at a phase where the instantaneous slope of the power-phase curve is steep and well below maximum power. We provide four lines of evidence demonstrating that, contrary to the current paradigm, the moth's nervous system establishes significant control authority in these muscles through precise timing modulation: (i) left-right pairs of flight muscles normally fire precisely, within 0.5-0.6 ms of each other; (ii) during a yawing optomotor response, left-right muscle timing differences shift throughout a wider 8 ms timing window, enabling at least a 50 per cent left-right power differential; (iii) timing differences correlate with turning torque; and (iv) the downstroke power muscles alone causally account for 47 per cent of turning torque. To establish (iv), we altered muscle activation during intact behaviour by stimulating individual muscle potentials to impose left-right timing differences. Because many organisms also have muscles operating with high power-phase gains (Δ(power)/Δ(phase)), this motor control strategy may be ubiquitous in locomotor systems.

Abdicating power for control: a precision timing strategy to modulate function of flight power muscles

PubMed Central

Sponberg, S.; Daniel, T. L.

2012-01-01

Muscles driving rhythmic locomotion typically show strong dependence of power on the timing or phase of activation. This is particularly true in insects' main flight muscles, canonical examples of muscles thought to have a dedicated power function. However, in the moth (Manduca sexta), these muscles normally activate at a phase where the instantaneous slope of the power–phase curve is steep and well below maximum power. We provide four lines of evidence demonstrating that, contrary to the current paradigm, the moth's nervous system establishes significant control authority in these muscles through precise timing modulation: (i) left–right pairs of flight muscles normally fire precisely, within 0.5–0.6 ms of each other; (ii) during a yawing optomotor response, left—right muscle timing differences shift throughout a wider 8 ms timing window, enabling at least a 50 per cent left–right power differential; (iii) timing differences correlate with turning torque; and (iv) the downstroke power muscles alone causally account for 47 per cent of turning torque. To establish (iv), we altered muscle activation during intact behaviour by stimulating individual muscle potentials to impose left—right timing differences. Because many organisms also have muscles operating with high power–phase gains (Δpower/Δphase), this motor control strategy may be ubiquitous in locomotor systems. PMID:22833272

Steering Clear of Driving After Drinking: a Tailored e-Health Intervention for Reducing Repeat Offending and Modifying Alcohol Use in a High-Risk Cohort.

PubMed

Wilson, Hollie Jai; Palk, Gavan; Sheehan, Mary Christina; Wishart, Darren; Watson, Barry

2017-10-01

Digital interventions to reduce risk behaviours are emerging as effective public health measures; however, few have been applied to drink driving and associated alcohol use based on a harm reduction perspective. This paper reports on the design, development, and pilot of a novel intervention which aims to reduce repeat offending by first-time convicted drink driving offenders. It explores whether an online program is acceptable and user friendly and contains useful and relevant content, with a sample of first-time drink driving offenders recruited at the time of conviction. Building upon existing research into interventions to reduce drink driving recidivism and problem alcohol use, a tailored program was designed to provide content specifically concerned with drink driving and with an additional component related to alcohol use. Following stakeholder and internal review, the 'Steering Clear First Offender Drink Driving Program' was subsequently piloted with 15 first-time drink driving offenders. Evaluative data was analysed both quantitatively and qualitatively. The pilot results indicate that the participants found the program to be user friendly, as demonstrated by high scores in relation to navigation, online delivery, engagement, avatar usage and straightforwardness. They reported that they found the content to be useful and relevant and that the key learning area was in relation to the consequences of drink driving. Online interventions for reducing risky behaviour such as drink driving may be useful and cost effective from a public health perspective. Potentially, they can directly address risky behaviours associated with alcohol use in high-risk cohorts that may not ordinarily receive intervention.

Relationship of Impaired Driving Enforcement Intensity to Drinking and Driving on the Roads

PubMed Central

Fell, James C.; Waehrer, Geetha; Voas, Robert B.; Auld-Owens, Amy; Carr, Katherine; Pell, Karen

2014-01-01

Background It is principally the area of enforcement that offers the greatest opportunity for reducing alcohol-impaired driving in the near future. How much of a reduction in drinking and driving would be achieved by how much improvement in enforcement intensity? Methods We developed logistic regression models to explore how enforcement intensity (six different measures) related to the prevalence of weekend, nighttime drivers in the 2007 National Roadside Survey (NRS) who had been drinking (blood alcohol concentration [BAC]>.00 g/dL), who had BACs>.05 g/dL, and who were driving with an illegal BAC>.08 g/dL. Results Drivers on the roads in our sample of 30 communities who were exposed to fewer than 228 traffic stops per 10,000 population aged 18 and older had 2.4 times the odds of being BAC positive, 3.6 times the odds of driving with a BAC>0.05, and 3.8 times the odds of driving with a BAC>0.08 compared to those drivers on the roads in communities with more than 1,275 traffic stops per 10,000 population. Drivers on the roads in communities with fewer than 3.7 driving-under-the-influence (DUI) arrests per 10,000 population had 2.7 times the odds of BAC-positive drivers on the roads compared to communities with the highest intensity of DUI arrest activity (>38 DUI arrests per 10,000 population). Conclusion The number of traffic stops and DUI arrests per capita were significantly associated with the odds of drinking and driving on the roads in these communities. This might reflect traffic enforcement visibility. The findings in this study may help law enforcement agencies around the country adjust their traffic enforcement intensity to reduce impaired driving in their community. PMID:25515820

DENSITY-MAGNETIC FIELD CORRELATION IN MAGNETOHYDRODYNAMIC TURBULENCE DRIVEN BY DIFFERENT DRIVING SCHEMES WITH DIFFERENT CORRELATION TIMES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoon, Heesun; Cho, Jungyeon; Kim, Jongsoo, E-mail: hsyoon@cnu.ac.kr, E-mail: jcho@cnu.ac.kr, E-mail: jskim@kasi.re.kr

Turbulent motions naturally produce density and magnetic-field fluctuations. Correlation between the two fluctuations is important for interpretation of observations, such as observations of the rotation measure (RM). In this paper, we study the effect of driving schemes on the density-magnetic-field correlation. In particular, we numerically investigate how the correlation time of driving affects the correlation between density and magnetic field. We perform compressible magnetohydrodynamic turbulence simulations at different sonic Mach numbers ( M {sub s} ), using two different driving schemes—a finite-correlated driving and a delta-correlated driving. In the former, the forcing vectors change continuously with a correlation time comparablemore » to the large-eddy turnover time. In the latter, the direction (and amplitude) of driving changes in a very short timescale. The finite-correlated driving results in strong anti-correlation between two fields when the sonic and the Alfvénic Mach numbers are similar to unity (i.e., when M {sub s} ∼ 1 and M {sub A} ∼ 1, respectively). However, the anti-correlation becomes weaker and approaches zero for higher values of M {sub s} or M {sub A}. The delta-correlated driving produces virtually no correlation between two fields when M {sub s} ∼ 1 and M {sub A} ∼ 1, and produces more and more positive correlations as M {sub s} or M {sub A} increases. We conjecture that two competing effects, tendency for achieving balance between the gas and the magnetic pressure and simultaneous compression of fluid and magnetic field, determine the correlation behavior. We also investigate how different driving schemes affect the Probability Density Function of three-dimensional density, dispersion measure, and RM.« less

Control of adaptive optic element displacement with the help of a magnetic rheology drive

NASA Astrophysics Data System (ADS)

Deulin, Eugeni A.; Mikhailov, Valeri P.; Sytchev, Victor V.

2000-10-01

The control system of adaptive optic of a large astronomical segmentated telescope was designed and tested. The dynamic model and the amplitude-frequency analysis of the new magnetic rheology (MR) drive are presented. The loop controlled drive consists of hydrostatic carrier, MR hydraulic loop controlling system, elastic thin wall seal, stainless seal which are united in a single three coordinate manipulator. This combination ensures short positioning error (delta) (phi)

Heritability of DUI convictions: a twin study of driving under the influence of alcohol.

PubMed

Anum, Emmanuel A; Silberg, Judy; Retchin, Sheldon M

2014-02-01

The study was undertaken to assess the relative contributions of genetic and environmental influences on drunk-driving. Driving records of a cohort of male and female twins (N = 17,360) from the Mid-Atlantic Twin Registry were examined. Structural equation models were used to estimate the magnitude of genetic and environmental effects on male and female phenotypes, and test for gender differences. There were significant gender and age effects. Compared with females, males were five times more likely to engage in driving under the influence. Among persons aged 21-49 years, the risk for drunk-driving was eight times that for those aged 50+ years and five times greater than those ≤20 years. In both males and females, aged 21-49 years, a large proportion (57%) of the variance in drunk-driving was due to genetic factors and the remaining 43% due to individual specific environmental influences. Drunk-driving is under significant genetic influence in both males and females. Our findings suggest that a different set of genes influence DUIs in men and women.

Distracted driving on YouTube: implications for adolescents.

PubMed

Basch, Corey H; Mouser, Christina; Clark, Ashley

2017-05-18

For the first time in 50 years, traffic fatalities have increased in the United States (US). With the emergence of technology, comes the possibility, that distracted driving has contributed to a decrease in safe driving practices. The purpose of this study was to describe the content on the popular video sharing site, YouTube to ascertain the type of content conveyed in videos that are widely viewed. The 100 most widely viewed English language videos were included in this sample, with a collective number of views of over 35 million. The majority of videos were television-based and Internet-based. Pairwise comparisons indicated that there were statistically significant differences between the number of views of consumer generated videos and television-based videos (p = 0.001) and between television-based videos and Internet-based videos (p < 0.001). Compared with consumer generated videos, television-based videos were 13 times more likely to discuss cell phone use as a distractor while driving, while Internet-based videos were 6.6 times more likely to discuss cell phone use as a distractor while driving. In addition, compared with consumer generated videos, television-based videos were 3.67 times more likely to discuss texting as a distractor while driving, whereas Internet-based videos were 8.5 times more likely to discuss texting as a distractor while driving. The findings of this study indicate that the videos on YouTube related to distracted driving are popular and that this medium could prove to be a successful venue to communicate information about this emergent public health issue.

Driver state examination--Treading new paths.

PubMed

Wascher, Edmund; Getzmann, Stephan; Karthaus, Melanie

2016-06-01

A large proportion of crashes in road driving can be attributed to driver fatigue. Several types of fatigue are discussed, comprising sleep-related fatigue, active task-related fatigue (as a consequence of workload in demanding driving situations) as well as passive task-related fatigue (as related to monotonous driving situations). The present study investigated actual states of fatigue in a monotonous driving situation, using EEG measures and a long-lasting driving simulation experiment, in which drivers had to keep the vehicle on track by compensating crosswind of different strength. Performance data and electrophysiological correlates of mental fatigue (EEG Alpha and Theta power, Inter Trial Coherence (ITC), and auditory event-related potentials to short sound stimuli) were analyzed. Driving errors and driving lane variability increased with time on task and with increasing crosswind. The posterior Alpha and Theta power also increased with time on task, but decreased with stronger crosswind. The P3a to sound stimuli decreased with time on task when the crosswind was weak, but remained stable when the crosswind was strong. The analysis of ITC revealed less frontal Alpha and Theta band synchronization with time on task, but no effect of crosswind. The results suggest that Alpha power in monotonous driving situations reflects boredom or attentional withdrawal due to monotony rather than the decline of processing abilities as a consequence of high mental effort. A more valid indicator of declining mental resources with increasing time on task seems to be provided by brain oscillatory synchronization measures and event-related activity. Copyright © 2016 Elsevier Ltd. All rights reserved.

Wind-enhanced resuspension in the shallow waters of South San Francisco Bay: Mechanisms and potential implications for cohesive sediment transport

USGS Publications Warehouse

Brand, Andreas; Lacy, Jessica R.; Hsu, Kevin; Hoover, Daniel; Gladding, Steve; Stacey, Mark T.

2010-01-01

We investigated the driving forces of sediment dynamics at the shoals in South San Francisco Bay. Two stations were deployed along a line perpendicular to a 14 m deep channel, 1000 and 2000 m from the middle of the channel. Station depths were 2.59 and 2.19 m below mean lower low water, respectively. We used acoustic Doppler velocimeters for the simultaneous determination of current velocities, turbulence, sediment concentration and fluxes. Maximum current shear velocities were 0.015 m s−1 at the station further from the channel (closer to the shore) and 0.02 m s−1 at the station closer to the channel. Peak wave-induced shear velocities exceeded 0.015 m s−1 at both stations. Maximum sediment concentrations were around 30 g m−3 during calm periods (root mean square wave height −3 and sediment fluxes were 5 times higher than in calm conditions (0.02 g m−2 s−1 versus >0.10 g m−2 s−1) at the station further from the channel 0.36 m above the bed. Closer to the channel, sediment concentrations and vertical fluxes due to wind wave resuspension were persistently lower (maximum concentrations around 50 g m−3 and maximum fluxes around 0.04 g m−2 s−1). Most resuspension events occurred during flood tides that followed wave events during low water. Although wave motions are able to resuspend sediment into the wave boundary layer at low tide, the observed large increases in sediment fluxes are due to the nonlinear interaction of wind waves and the tidal currents.

The Southern Glacial Maximum 65,000 years ago and its Unfinished Termination

NASA Astrophysics Data System (ADS)

Schaefer, Joerg M.; Putnam, Aaron E.; Denton, George H.; Kaplan, Michael R.; Birkel, Sean; Doughty, Alice M.; Kelley, Sam; Barrell, David J. A.; Finkel, Robert C.; Winckler, Gisela; Anderson, Robert F.; Ninneman, Ulysses S.; Barker, Stephen; Schwartz, Roseanne; Andersen, Bjorn G.; Schluechter, Christian

2015-04-01

Glacial maxima and their terminations provide key insights into inter-hemispheric climate dynamics and the coupling of atmosphere, surface and deep ocean, hydrology, and cryosphere, which is fundamental for evaluating the robustness of earth's climate in view of ongoing climate change. The Last Glacial Maximum (LGM, ∼26-19 ka ago) is widely seen as the global cold peak during the last glacial cycle, and its transition to the Holocene interglacial, dubbed 'Termination 1 (T1)', as the most dramatic climate reorganization during this interval. Climate records show that over the last 800 ka, ice ages peaked and terminated on average every 100 ka ('100 ka world'). However, the mechanisms pacing glacial-interglacial transitions remain controversial and in particular the hemispheric manifestations and underlying orbital to regional driving forces of glacial maxima and subsequent terminations remain poorly understood. Here we show evidence for a full glacial maximum in the Southern Hemisphere 65.1 ± 2.7 ka ago and its 'Unfinished Termination'. Our 10Be chronology combined with a model simulation demonstrates that New Zealand's glaciers reached their maximum position of the last glacial cycle during Marine Isotope Stage-4 (MIS-4). Southern ocean and greenhouse gas records indicate coeval peak glacial conditions, making the case for the Southern Glacial Maximum about halfway through the last glacial cycle and only 15 ka after the last warm period (MIS-5a). We present the hypothesis that subsequently, driven by boreal summer insolation forcing, a termination began but remained unfinished, possibly because the northern ice sheets were only moderately large and could not supply enough meltwater to the North Atlantic through Heinrich Stadial 6 to drive a full termination. Yet the Unfinished Termination left behind substantial ice on the northern continents (about 50% of the full LGM ice volume) and after another 45 ka of cooling and ice sheet growth the earth was at inter-hemispheric Last Glacial Maximum configuration, when similar orbital forcing hit maximum-size northern ice sheets and ushered in T1 and thus the ongoing interglacial. This argument highlights the critical role of full glacial conditions in both hemispheres for terminations and implies that the Southern Hemisphere climate could transition from interglacial to full glacial conditions in about 15,000 years, while the Northern Hemisphere and its continental ice-sheets required half a glacial cycle.

Shoulder muscle forces during driving: Sudden steering can load the rotator cuff beyond its repair limit

PubMed Central

Pandis, Petros; Prinold, Joe A.I.; Bull, Anthony M.J.

2015-01-01

Background Driving is one of the most common everyday tasks and the rotator cuff muscles are the primary shoulder stabilisers. Muscle forces during driving are not currently known, yet knowledge of these would influence important clinical advice such as return to activities after surgery. The aim of this study is to quantify shoulder and rotator cuff muscle forces during driving in different postures. Methods A musculoskeletal modelling approach is taken, using a modified driving simulator in combination with an upper limb musculoskeletal model (UK National Shoulder Model). Motion data and external force vectors were model inputs and upper limb muscle and joint forces were the outputs. Findings Comparisons of the predicted glenohumeral joint forces were compared to in vivo literature values, with good agreement demonstrated (61 SD 8% body weight mean peak compared to 60 SD 1% body weight mean peak). High muscle activation was predicted in the rotator cuff muscles; particularly supraspinatus (mean 55% of the maximum and up to 164 SD 27 N). This level of loading is up to 72% of mean failure strength for supraspinatus repairs, and could therefore be dangerous for some cases. Statistically significant and large differences are shown to exist in the joint and muscle forces for different driving positions as well as steering with one or both hands (up to 46% body weight glenohumeral joint force). Interpretation These conclusions should be a key consideration in rehabilitating the shoulder after surgery, preventing specific upper limb injuries and predicting return to driving recommendations. PMID:26139549

[A literature review on epidemiologic research on sleep disturbances in the elderly].

PubMed

Doi, Yuriko

2015-06-01

One of the issues facing our super-aging society of Japan is to secure the elderly's safety and health. According to the latest 10-year statistics of the National Police Agency, the number of elderly driving deaths 75 years of age and over has risen 1.3 times from 2003 to 2013, whereas driving deaths decreased by less than half among the people under age 75 during the same period of time. This paper reviews the current literature on epidemiologic studies investigating the associations of sleep disturbances with adverse driving events and driving practice among elderly drivers. The results suggest a cognitive behavioral therapy for insomnia as a promising method for improving their driving capacity. Key words: elderly driving, epidemiology, sleep disturbances

Assessment of driving-related performance in chronic whiplash using an advanced driving simulator.

PubMed

Takasaki, Hiroshi; Treleaven, Julia; Johnston, Venerina; Rakotonirainy, Andry; Haines, Andrew; Jull, Gwendolen

2013-11-01

Driving is often nominated as problematic by individuals with chronic whiplash associated disorders (WAD), yet driving-related performance has not been evaluated objectively. The purpose of this study was to test driving-related performance in persons with chronic WAD against healthy controls of similar age, gender and driving experience to determine if driving-related performance in the WAD group was sufficiently impaired to recommend fitness to drive assessment. Driving-related performance was assessed using an advanced driving simulator during three driving scenarios; freeway, residential and a central business district (CBD). Total driving duration was approximately 15min. Five driving tasks which could cause a collision (critical events) were included in the scenarios. In addition, the effect of divided attention (identify red dots projected onto side or rear view mirrors) was assessed three times in each scenario. Driving performance was measured using the simulator performance index (SPI) which is calculated from 12 measures. z-Scores for all SPI measures were calculated for each WAD subject based on mean values of the control subjects. The z-scores were then averaged for the WAD group. A z-score of ≤-2 indicated a driving failing grade in the simulator. The number of collisions over the five critical events was compared between the WAD and control groups as was reaction time and missed response ratio in identifying the red dots. Seventeen WAD and 26 control subjects commenced the driving assessment. Demographic data were comparable between the groups. All subjects completed the freeway scenario but four withdrew during the residential and eight during the CBD scenario because of motion sickness. All scenarios were completed by 14 WAD and 17 control subjects. Mean z-scores for the SPI over the three scenarios was statistically lower in the WAD group (-0.3±0.3; P<0.05) but the score was not below the cut-off point for safe driving. There were no differences in the reaction time and missed response ratio in divided attention tasks between the groups (All P>0.05). Assessment of driving in an advanced driving simulator for approximately 15min revealed that driving-related performance in chronic WAD was not sufficiently impaired to recommend the need for fitness to drive assessment. Copyright © 2013 Elsevier Ltd. All rights reserved.

Next generation smart window display using transparent organic display and light blocking screen.

PubMed

Kim, Gyeong Woo; Lampande, Raju; Choe, Dong Cheol; Ko, Ik Jang; Park, Jin Hwan; Pode, Ramchandra; Kwon, Jang Hyuk

2018-04-02

Transparent organic light emitting diodes (TOLED) have widespread applications in the next-generation display devices particularly in the large size transparent window and interactive displays. Herein, we report high performance and stable attractive smart window displays using facile process. Advanced smart window display is realized by integrating the high performance light blocking screen and highly transparent white OLED panel. The full smart window display reveals a maximum transmittance as high as 64.2% at the wavelength of 600 nm and extremely good along with tunable ambient contrast ratio (171.94:1) compared to that of normal TOLED (4.54:1). Furthermore, the performance decisive light blocking screen has demonstrated an excellent optical and electrical characteristics such as i) high transmittance (85.56% at 562nm) at light-penetrating state, ii) superior absorbance (2.30 at 562nm) in light interrupting mode, iii) high optical contrast (85.50 at 562 nm), iv) high optical stability for more than 25,000 cycle of driving, v) fast switching time of 1.9 sec, and vi) low driving voltage of 1.7 V. The experimental results of smart window display are also validated using optical simulation. The proposed smart window display technology allows us to adjust the intensity of daylight entering the system quickly and conveniently.

Eutrophication in Poyang Lake (Eastern China) over the Last 300 Years in Response to Changes in Climate and Lake Biomass

PubMed Central

Liao, Mengna; Yu, Ge; Guo, Ya

2017-01-01

Poyang Lake is suffering from persistent eutrophication, which is degrading the local ecosystem. A better understanding of the mechanisms that drive eutrophication in lake systems is essential to fight the ongoing deterioration. In this study, hydraulic residence time (HRT) was used to evaluate Poyang Lake’s trophic state. A hydrology and ecosystem forced model was constructed to simulate long-term changes in algae and aquatic plant biomass and total phosphorous (TP). A comparison analysis revealed that between 1812 and 1828 (i.e., a consistent-change stage), climate and hydrology were the main driving forces, while algae and aquatic plant biomass contributed only 20.9% to the trophic changes in Poyang Lake. However, between 1844 and 1860 the biomass predominated contributing 63.6%. This could be attributed to nutrient absorption by algae and aquatic plants. A correlation analysis of the water TP and algae and aquatic plant biomass revealed a strong positive relationship. However, the algae and aquatic plant growth rate tended to decline after the biomass reached half of the maximum. This research reconstructs the long-term trophic evolution of Poyang Lake and provides a better understanding of the relationship between climatic and hydrological changes and lake ecosystems. PMID:28046083

Assessing the Driver’s Current Level of Working Memory Load with High Density Functional Near-infrared Spectroscopy: A Realistic Driving Simulator Study

PubMed Central

Unni, Anirudh; Ihme, Klas; Jipp, Meike; Rieger, Jochem W.

2017-01-01

Cognitive overload or underload results in a decrease in human performance which may result in fatal incidents while driving. We envision that driver assistive systems which adapt their functionality to the driver’s cognitive state could be a promising approach to reduce road accidents due to human errors. This research attempts to predict variations of cognitive working memory load levels in a natural driving scenario with multiple parallel tasks and to reveal predictive brain areas. We used a modified version of the n-back task to induce five different working memory load levels (from 0-back up to 4-back) forcing the participants to continuously update, memorize, and recall the previous ‘n’ speed sequences and adjust their speed accordingly while they drove for approximately 60 min on a highway with concurrent traffic in a virtual reality driving simulator. We measured brain activation using multichannel whole head, high density functional near-infrared spectroscopy (fNIRS) and predicted working memory load level from the fNIRS data by combining multivariate lasso regression and cross-validation. This allowed us to predict variations in working memory load in a continuous time-resolved manner with mean Pearson correlations between induced and predicted working memory load over 15 participants of 0.61 [standard error (SE) 0.04] and a maximum of 0.8. Restricting the analysis to prefrontal sensors placed over the forehead reduced the mean correlation to 0.38 (SE 0.04), indicating additional information gained through whole head coverage. Moreover, working memory load predictions derived from peripheral heart rate parameters achieved much lower correlations (mean 0.21, SE 0.1). Importantly, whole head fNIRS sampling revealed increasing brain activation in bilateral inferior frontal and bilateral temporo-occipital brain areas with increasing working memory load levels suggesting that these areas are specifically involved in workload-related processing. PMID:28424602

Influence of water table fluctuations on subsurface methane dynamics and surface fluxes in seasonally flooded subtropical pastures.

NASA Astrophysics Data System (ADS)

Chamberlain, S.; Gomez-Casanovas, N.; Boughton, E.; Keel, E.; Walter, M. T.; Groffman, P. M.; Sparks, J. P.

2015-12-01

Seasonally flooded subtropical pastures are major sources of methane (CH4), and periodic flooding drives complex emission dynamics from these ecosystems. Understanding the mechanisms of belowground CH4 dynamics driving soil surface fluxes is needed to better understand emissions from these systems and their response to environmental change. We investigated subsurface CH4 dynamics in relation to net surface fluxes using laboratory water table manipulations and compared these results to eddy covariance-measured fluxes to link within-soil CH4 dynamics to observed ecosystem fluxes. Pronounced hysteresis was observed in ecosystem CH4 fluxes during precipitation driven flooding events. This dynamic was replicated in mesocosm experiments, with maximum CH4 fluxes observed during periods of water table recession. Hysteresis dynamics were best explained by oxygen dynamics during precipitation recharge events and the oxidation of CH4 produced in organic soil horizons during water table recession. We observed distinct CH4 dynamics between surface organic and deeper mineral soil horizons. In surface organic soil horizons, high levels of CH4 production were temporally linked to observed surface emissions. In contrast, high concentrations of CH4 observed in deeper mineral soils did not contribute to surface fluxes. Methane production potentials in surface organic soils were orders of magnitude higher than in mineral soils, suggesting that over longer flooding regimes CH4 produced in mineral horizons is unlikely to be a significant component of net surface emissions. Our results demonstrate that distinct CH4 dynamics may be stratified by depth, and flooding of the near-surface organic soils drives the high magnitude CH4 fluxes observed from subtropical pastures. These results suggest that relatively small changes in pasture water table dynamics can drive large changes in net CH4 emissions if surface organic soils remain saturated over longer time scales.

Assessing the Driver's Current Level of Working Memory Load with High Density Functional Near-infrared Spectroscopy: A Realistic Driving Simulator Study.

PubMed

Unni, Anirudh; Ihme, Klas; Jipp, Meike; Rieger, Jochem W

2017-01-01

Cognitive overload or underload results in a decrease in human performance which may result in fatal incidents while driving. We envision that driver assistive systems which adapt their functionality to the driver's cognitive state could be a promising approach to reduce road accidents due to human errors. This research attempts to predict variations of cognitive working memory load levels in a natural driving scenario with multiple parallel tasks and to reveal predictive brain areas. We used a modified version of the n-back task to induce five different working memory load levels (from 0-back up to 4-back) forcing the participants to continuously update, memorize, and recall the previous 'n' speed sequences and adjust their speed accordingly while they drove for approximately 60 min on a highway with concurrent traffic in a virtual reality driving simulator. We measured brain activation using multichannel whole head, high density functional near-infrared spectroscopy (fNIRS) and predicted working memory load level from the fNIRS data by combining multivariate lasso regression and cross-validation. This allowed us to predict variations in working memory load in a continuous time-resolved manner with mean Pearson correlations between induced and predicted working memory load over 15 participants of 0.61 [standard error (SE) 0.04] and a maximum of 0.8. Restricting the analysis to prefrontal sensors placed over the forehead reduced the mean correlation to 0.38 (SE 0.04), indicating additional information gained through whole head coverage. Moreover, working memory load predictions derived from peripheral heart rate parameters achieved much lower correlations (mean 0.21, SE 0.1). Importantly, whole head fNIRS sampling revealed increasing brain activation in bilateral inferior frontal and bilateral temporo-occipital brain areas with increasing working memory load levels suggesting that these areas are specifically involved in workload-related processing.

Personal and contextual factors in the escalation of driving after drinking across the college years.

PubMed

Quinn, Patrick D; Fromme, Kim

2012-12-01

College students continue to drive after drinking at alarmingly high rates. Age trends suggest that driving after drinking increases from late adolescence across the college years, largely mirroring trends in binge drinking. Relatively little research, however, has examined change over time in driving after drinking among college students or tested whether some students might be at greater risk of escalations in driving after drinking. Using a sample of 1,833 nonabstaining students who completed surveys for seven semesters across the college years, we tested whether personal (i.e., age of drinking onset, gender, risk perceptions, and sensation seeking) and contextual (i.e., college residence) factors were associated with changes in driving after drinking. Using latent growth curve modeling, we found significant individual differences in rates of change in driving after drinking. Male students and students who began drinking earlier in life increased in driving after drinking more rapidly, whereas living in on-campus housing was associated with time-specific decreases in driving after drinking. These results demonstrate the value of considering driving after drinking from a longitudinal perspective and suggest possible avenues toward preventing the public health consequences of intoxicated driving. 2013 APA, all rights reserved

Objective assessment of the effects of texting while driving: a simulator study.

PubMed

Bendak, Salaheddine

2015-01-01

Recent advances in electronic communication technology led to many drivers opting to send and receive text messages while driving. This, inevitably, has a potential to distract drivers, impair driving performance and lead to crashes. This study aims to assess the risk involved in texting while driving through assessing the distraction caused and determining the change in key driving performance indicators. Twenty-one paid young male volunteers were recruited to participate in this study. Each participant drove a driving simulator on four different scenarios involving driving while texting and without texting on highways and town roads. Results showed that texting while driving led, on average, to five times more crashes than driving without texting. Due to distraction also, participants unnecessarily crossed lane boundaries and road boundaries more often while texting as compared to driving without texting. Moreover, distraction due to texting led to participants deviating their eyes off the road while texting 15 times per session, on average, more than without texting. Results demonstrated a high-risk level of distraction and clear impairment in drivers' ability to drive safely due to texting. Based on the results, practical recommendations to combat this phenomenon are given.

Personal and Contextual Factors in the Escalation of Driving after Drinking Across the College Years

PubMed Central

Quinn, Patrick D.; Fromme, Kim

2014-01-01

College students continue to drive after drinking at alarmingly high rates. Age trends suggest that driving after drinking increases from late adolescence across the college years, largely mirroring trends in binge drinking. Relatively little research, however, has examined change over time in driving after drinking among college students or tested whether some students might be at greater risk of escalations in driving after drinking. Using a sample of 1,833 non-abstaining students who completed surveys for 7 semesters across the college years, we tested whether personal (i.e., age of drinking onset, gender, risk perceptions, and sensation seeking) and contextual (i.e., college residence) factors were associated with changes in driving after drinking. Using latent growth curve modeling, we found significant individual differences in rates of change in driving after drinking. Male students and students who began drinking earlier in life increased in driving after drinking more rapidly, whereas living in on-campus housing was associated with time-specific decreases in driving after drinking. These results demonstrate the value of considering driving after drinking from a longitudinal perspective and suggest possible avenues toward preventing the public health consequences of intoxicated driving. PMID:22229535

Two-Dimensional Analysis of Conical Pulsed Inductive Plasma Thruster Performance

NASA Technical Reports Server (NTRS)

Hallock, A. K.; Polzin, K. A.; Emsellem, G. D.

2011-01-01

A model of the maximum achievable exhaust velocity of a conical theta pinch pulsed inductive thruster is presented. A semi-empirical formula relating coil inductance to both axial and radial current sheet location is developed and incorporated into a circuit model coupled to a momentum equation to evaluate the effect of coil geometry on the axial directed kinetic energy of the exhaust. Inductance measurements as a function of the axial and radial displacement of simulated current sheets from four coils of different geometries are t to a two-dimensional expression to allow the calculation of the Lorentz force at any relevant averaged current sheet location. This relation for two-dimensional inductance, along with an estimate of the maximum possible change in gas-dynamic pressure as the current sheet accelerates into downstream propellant, enables the expansion of a one-dimensional circuit model to two dimensions. The results of this two-dimensional model indicate that radial current sheet motion acts to rapidly decouple the current sheet from the driving coil, leading to losses in axial kinetic energy 10-50 times larger than estimations of the maximum available energy in the compressed propellant. The decreased available energy in the compressed propellant as compared to that of other inductive plasma propulsion concepts suggests that a recovery in the directed axial kinetic energy of the exhaust is unlikely, and that radial compression of the current sheet leads to a loss in exhaust velocity for the operating conditions considered here.

Mild Cognitive Impairment and driving: Does in-vehicle distraction affect driving performance?

PubMed

Beratis, Ion N; Pavlou, Dimosthenis; Papadimitriou, Eleonora; Andronas, Nikolaos; Kontaxopoulou, Dionysia; Fragkiadaki, Stella; Yannis, George; Papageorgiou, Sokratis G

2017-06-01

In-vehicle distraction is considered to be an important cause of road accidents. Drivers with Mild Cognitive Impairment (MCI), because of their attenuated cognitive resources, may be vulnerable to the effects of distraction; however, previous relevant research is lacking. The main objective of the current study was to explore the effect of in-vehicle distraction on the driving performance of MCI patients, by assessing their reaction time at unexpected incidents and accident probability. Thirteen patients with MCI (age: 64.5±7.2) and 12 cognitively intact individuals (age: 60.0±7.7), all active drivers were introduced in the study. The driving simulator experiment included three distraction conditions: (a) undistracted driving, (b) conversing with passenger and (c) conversing through a hand-held mobile phone. The mixed ANOVA models revealed a greater effect of distraction on MCI patients. Specifically, the use of mobile phone induced a more pronounced impact on reaction time and accident probability in the group of patients, as compared to healthy controls. On the other hand, in the driving condition "conversing with passenger" the interaction effects regarding reaction time and accident probability were not significant. Notably, the aforementioned findings concerning the MCI patients in the case of the mobile phone were observed despite the effort of the drivers to apply a compensatory strategy by reducing significantly their speed in this driving condition. Overall, the current findings indicate, for the first time, that a common driving practice, such as the use of mobile phone, may have a detrimental impact on the driving performance of individuals with MCI. Copyright © 2017. Published by Elsevier Ltd.

The Corrosion Characteristics and Tensile Behavior of Reinforcement under Coupled Carbonation and Static Loading

PubMed Central

Xu, Yidong

2015-01-01

This paper describes the non-uniform corrosion characteristics and mechanical properties of reinforcement under coupled action of carbonation and static loading. The two parameters, namely area-box (AB) value and arithmetical mean deviation (Ra), are adopted to characterize the corrosion morphology and pitting distribution from experimental observations. The results show that the static loading affects the corrosion characteristics of reinforcement. Local stress concentration in corroded reinforcement caused by tensile stress drives the corrosion pit pattern to be more irregular. The orthogonal test results from finite element simulations show that pit shape and pit depth are the two significant factors affecting the tensile behavior of reinforcement. Under the condition of similar corrosion mass loss ratio, the maximum plastic strain of corroded reinforcement increases with the increase of Ra and load time-history significantly. PMID:28793729

PRESSURE PULSES AT VOYAGER 2 : DRIVERS OF INTERSTELLAR TRANSIENTS?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Richardson, J. D.; Wang, C.; Liu, Y. D.

Voyager 1 ( V1 ) crossed the heliopause into the local interstellar medium (LISM) in 2012. The LISM is a dynamic region periodically disturbed by solar transients with outward-propagating shocks, cosmic-ray intensity changes and anisotropies, and plasma wave oscillations. Voyager 2 ( V2 ) trails V1 and thus may observe the solar transients that are later observed at V1. V2 crossed the termination shock in 2007 and is now in the heliosheath. Starting in 2012, when solar maximum conditions reached V2 , five possible merged interaction regions (MIRs) have been observed by V2 in the heliosheath. The timing is consistentmore » with these MIRs driving the transients observed by V1 in the LISM. The largest heliosheath MIR was observed by V2 in late 2015 and should reach V1 in 2018.« less

Defining the health care product to ensure quality and manage costs.

PubMed

Burns, J

1994-02-01

The frenzy of health care reform activity now led by the Clinton Administration's American Health Security Act of 1993 might end in the worst of all possible outcomes: a new government entitlement program financed by business and a global budget. Unbridled entitlement could drive utilization of benefits to the maximum and, with a budget cap, guarantee rationing. So far, the administration has talked about expanding access and controlling costs--not about the health care product. Given the threat that change poses for vested interests, time will undoubtedly lapse before final implementation of a new system. Unless physicians involved in health management seize the opportunity during this window of opportunity to help shape the future of health care delivery, the likelihood of preserving the U.S. health care delivery system as we know it will be dim indeed.

Useful field of view in simulated driving: Reaction times and eye movements of drivers

PubMed Central

Seya, Yasuhiro; Nakayasu, Hidetoshi; Yagi, Tadasu

2013-01-01

To examine the spatial distribution of a useful field of view (UFOV) in driving, reaction times (RTs) and eye movements were measured in simulated driving. In the experiment, a normal or mirror-reversed letter “E” was presented on driving images with different eccentricities and directions from the current gaze position. The results showed significantly slower RTs in the upper and upper left directions than in the other directions. The RTs were significantly slower in the left directions than in the right directions. These results suggest that the UFOV in driving may be asymmetrical among the meridians in the visual field. PMID:24349688

A comparison of the effect of mobile phone use and alcohol consumption on driving simulation performance.

PubMed

Leung, Sumie; Croft, Rodney J; Jackson, Melinda L; Howard, Mark E; McKenzie, Raymond J

2012-01-01

The present study compared the effects of a variety of mobile phone usage conditions to different levels of alcohol intoxication on simulated driving performance and psychomotor vigilance. Twelve healthy volunteers participated in a crossover design in which each participant completed a simulated driving task on 2 days, separated by a 1-week washout period. On the mobile phone day, participants performed the simulated driving task under each of 4 conditions: no phone usage, a hands-free naturalistic conversation, a hands-free cognitively demanding conversation, and texting. On the alcohol day, participants performed the simulated driving task at four different blood alcohol concentration (BAC) levels: 0.00, 0.04, 0.07, and 0.10. Driving performance was assessed by variables including time within target speed range, time spent speeding, braking reaction time, speed deviation, and lateral lane position deviation. In the BAC 0.07 and 0.10 alcohol conditions, participants spent less time in the target speed range and more time speeding and took longer to brake in the BAC 0.04, 0.07, and 0.10 than in the BAC 0.00 condition. In the mobile phone condition, participants took longer to brake in the natural hands-free conversation, cognitively demanding hands-free conversation and texting conditions and spent less time in the target speed range and more time speeding in the cognitively demanding, hands-free conversation, and texting conditions. When comparing the 2 conditions, the naturalistic conversation was comparable to the legally permissible BAC level (0.04), and the cognitively demanding and texting conversations were similar to the BAC 0.07 to 0.10 results. The findings of the current laboratory study suggest that very simple conversations on a mobile phone may not represent a significant driving risk (compared to legally permissible BAC levels), whereas cognitively demanding, hands-free conversation, and particularly texting represent significant risks to driving.

Correlation between Driver Subjective Fatigue and Bus Lateral Position in a Driving Simulator.

PubMed

Gharagozlou, Faramarz; Mazloumi, Adel; Saraji, Gebraeil Nasl; Nahvi, Ali; Ashouri, Mohammadreza; Mozaffari, Hamed

2015-08-01

Driver fatigue as a leading cause of death in the transportation industry can impair the driving performance in long-distance driving task. Studies on the links of driver subjective fatigue and the bus lateral position are still an exploratory issue that requires further investigation. This study aimed to determine the correlation between the driver subjective fatigue and the bus lateral position in a driving simulator. This descriptive-analytical research was conducted on 30 professional male bus drivers participated in a two-hour driving session. The driver subjective fatigue was assessed by the Fatigue Visual Analogue Scale (F-VAS) at 10-min intervals. Simultaneously, the performance measures of lane drifting as the mean and standard deviation of the bus lateral position (SDLP) were calculated during the simulated driving task. Descriptive statistics and the Spearman correlation coefficient were used to describe and analyze the data. Fatigue levels had an increasing trend as the time-on-task of driving increased. Time-on-task of driving had the greatest effect on the fatigue self-evaluation (r = 0.605, p < 0.0001). The results showed a significant correlation between fatigue self-evaluation and bus lateral position (r = 0.567, p < 0.0001). As the time of driving increased, driving performance was affected adversely, as shown by the increase in the SDLP. Even so, the effect of individual differences on driving performance should not be overlooked. This work concludes that predicting the state of a driver fatigue based on the group mean data has some complications for any application.

Correlation between Driver Subjective Fatigue and Bus Lateral Position in a Driving Simulator

PubMed Central

Gharagozlou, Faramarz; Mazloumi, Adel; Saraji, Gebraeil Nasl; Nahvi, Ali; Ashouri, Mohammadreza; Mozaffari, Hamed

2015-01-01

Background: Driver fatigue as a leading cause of death in the transportation industry can impair the driving performance in long-distance driving task. Studies on the links of driver subjective fatigue and the bus lateral position are still an exploratory issue that requires further investigation. This study aimed to determine the correlation between the driver subjective fatigue and the bus lateral position in a driving simulator. Methods: This descriptive-analytical research was conducted on 30 professional male bus drivers participated in a two-hour driving session. The driver subjective fatigue was assessed by the Fatigue Visual Analogue Scale (F-VAS) at 10-min intervals. Simultaneously, the performance measures of lane drifting as the mean and standard deviation of the bus lateral position (SDLP) were calculated during the simulated driving task. Descriptive statistics and the Spearman correlation coefficient were used to describe and analyze the data. Results: Fatigue levels had an increasing trend as the time-on-task of driving increased. Time-on-task of driving had the greatest effect on the fatigue self-evaluation (r = 0.605, p < 0.0001). The results showed a significant correlation between fatigue self-evaluation and bus lateral position (r = 0.567, p < 0.0001). Conclusion: As the time of driving increased, driving performance was affected adversely, as shown by the increase in the SDLP. Even so, the effect of individual differences on driving performance should not be overlooked. This work concludes that predicting the state of a driver fatigue based on the group mean data has some complications for any application. PMID:26396734

Factors affecting stability and change in risky driving from late adolescence to the late twenties.

PubMed

Vassallo, Suzanne; Lahausse, Julie; Edwards, Ben

2016-03-01

The risky driving tendencies of young drivers has been extensively researched, but much less is known about across-time patterns of risky driving behavior and the factors which influence these. This study identified factors associated with stable, increasing and decreasing risky driving trajectories among 751 Australian drivers participating in an ongoing longitudinal study. Five groups were formed on the basis of participants' patterns of risky driving from 19-20 to 27-28 years (i.e., stable low-risk, stable speeding, stable high-risk, increasing and decreasing). Very few participants exhibited a stable high-risk pattern. Characteristics that differentiated the different across-time groups were identified using Multinomial Logistic Regression. The most consistent correlates of risky driving patterns were antisocial behavior, binge drinking and relationship status. Sex, school completion, temperament, civic engagement, and antisocial peer friendships were also correlated with different across-time patterns. The implications of these findings for road safety are discussed. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

The Solar Wind Environment in Time

NASA Astrophysics Data System (ADS)

Pognan, Quentin; Garraffo, Cecilia; Cohen, Ofer; Drake, Jeremy J.

2018-03-01

We use magnetograms of eight solar analogs of ages 30 Myr–3.6 Gyr obtained from Zeeman Doppler Imaging and taken from the literature, together with two solar magnetograms, to drive magnetohydrodynamical wind simulations and construct an evolutionary scenario of the solar wind environment and its angular momentum loss rate. With observed magnetograms of the radial field strength as the only variant in the wind model, we find that a power-law model fitted to the derived angular momentum loss rate against time, t, results in a spin-down relation Ω ∝ t ‑0.51, for angular speed Ω, which is remarkably consistent with the well-established Skumanich law Ω ∝ t ‑0.5. We use the model wind conditions to estimate the magnetospheric standoff distances for an Earth-like test planet situated at 1 au for each of the stellar cases, and to obtain trends of minimum and maximum wind ram pressure and average ram pressure in the solar system through time. The wind ram pressure declines with time as \\overline{{P}ram}}\\propto {t}2/3, amounting to a factor of 50 or so over the present lifetime of the solar system.

The influence of cruise control and adaptive cruise control on driving behaviour--a driving simulator study.

PubMed

Markvollrath; Schleicher, Susanne; Gelau, Christhard

2011-05-01

Although Cruise Control (CC) is available for most cars, no studies have been found which examine how this automation system influences driving behaviour. However, a relatively large number of studies have examined Adaptive Cruise Control (ACC) which compared to CC includes also a distance control. Besides positive effects with regard to a better compliance to speed limits, there are also indications of smaller distances to lead vehicles and slower responses in situations that require immediate braking. Similar effects can be expected for CC as this system takes over longitudinal control as well. To test this hypothesis, a simulator study was conducted at the German Aerospace Center (DLR). Twenty-two participants drove different routes (highway and motorway) under three different conditions (assisted by ACC, CC and manual driving without any system). Different driving scenarios were examined including a secondary task condition. On the one hand, both systems lead to lower maximum velocities and less speed limit violations. There was no indication that drivers shift more of their attention towards secondary tasks when driving with CC or ACC. However, there were delayed driver reactions in critical situations, e.g., in a narrow curve or a fog bank. These results give rise to some caution regarding the safety effects of these systems, especially if in the future their range of functionality (e.g., ACC Stop-and-Go) is further increased. Copyright © 2011 Elsevier Ltd. All rights reserved.

Distribution of the near-inertial kinetic energy inside mesoscale eddies: Observations in the Gulf of Mexico

NASA Astrophysics Data System (ADS)

Ixetl Garcia Gomez, Beatriz; Pallas Sanz, Enric; Candela Perez, Julio

2017-04-01

The near-inertial oscillations (NIOs), generated by the wind stress on the surface mixed layer, are the inertia gravity waves with the lowest frequency and the highest kinetic energy. NIOs are important because they drive vertical mixing in the interior ocean during wave breaking events. Although the interaction between NIOs and mesoscale eddies has been reported by several authors, these studies are mostly analytical and numerical, and only few observational studies have attempted to show the differences in near-inertial kinetic energy (KEi) between anticyclonic and cyclonic eddies. In this work the spatial structure of the KEi inside the mesoscale eddies is computed using daily satellite altimetry and observations of horizontal velocity from 23 moorings equipped with acoustic Doppler current profilers in the western Gulf of Mexico. Consistent to theory, the obtained four-year KEi-composites show two times more KEi inside the anticyclonic eddies than inside the cyclonic ones. The vertical and horizontal cross-sections of the KEi-composites show that the KEi is mainly located near to the surface of the cyclonic eddies (positive vorticity), whereas the KEi in anticyclonic eddies (negative vorticity) is maximum in the eddy's center near to the base of the eddy where the NIOs become more inertial, are trapped, and amplified. The mean vertical profiles show that the cyclonic eddies present a maximum of KEi near to the surface at 50, while the maximum of KEi in the anticyclonic eddies occurs between 900 and 1100 m. Inside anticyclonic eddies another two relative maximums are observed, one in the mixed layer and the second at 300 m. In contrast, the mean profile of KEi outside the mesoscale eddies has the maximum value at the surface ( 50 m), with high values of KEi in the first 200 m and negligible energy beneath that depth. A different mean distribution of the KEi is observed depending on the type of wind generator: tropical storms or unidirectional wind.

Expiratory and phonation times as measures of disease severity in patients with Multiple Sclerosis. A case-control study.

PubMed

Nordio, Sara; Bernitsas, Evanthia; Meneghello, Francesca; Palmer, Katie; Stabile, Maria Rosaria; Dipietro, Laura; Di Stadio, Arianna

2018-04-21

Speech disorders are common in patients with Multiple Sclerosis (MS). They can be assessed with several methods, which are however expensive, complex, and not easily accessible to physicians during routine clinic visits. This study aimed at measuring maximum phonation times, maximum expiratory times, and articulation abilities scores in patients with MS compared to healthy subjects and at investigating if any of these parameters could be used as a measure of MS progression. 50 MS patients and 50 gender- and age-matched healthy controls were enrolled in the study. Maximum expiratory times and maximum phonation times were collected from both groups. Articulation abilities were evaluated using the articulation subtest from the Fussi assessment (dysarthria scores). MS patients were evaluated with the Expanded Disability Status Scale (EDSS). Correlations between EDSS scores and maximum expiratory times, maximum phonation times, and dysarthria scores were calculated. EDSS scores of MS patients ranged from 4.5 to 7.5. In MS patients, maximum expiratory times, maximum phonation times, and dysarthria scores were significantly altered compared to healthy controls. Moreover, the EDSS scores were correlated with the maximum expiratory times; the maximum expiratory times were correlated with the maximum phonation times, and the maximum phonation times were correlated with the dysarthria scores. As the expiratory times were significantly correlated with the EDSS scores, they could be used to measure the severity of MS and to monitor its progression. Copyright © 2018 Elsevier B.V. All rights reserved.

Monitoring sleepiness with on-board electrophysiological recordings for preventing sleep-deprived traffic accidents.

PubMed

Papadelis, Christos; Chen, Zhe; Kourtidou-Papadeli, Chrysoula; Bamidis, Panagiotis D; Chouvarda, Ioanna; Bekiaris, Evangelos; Maglaveras, Nikos

2007-09-01

The objective of this study is the development and evaluation of efficient neurophysiological signal statistics, which may assess the driver's alertness level and serve as potential indicators of sleepiness in the design of an on-board countermeasure system. Multichannel EEG, EOG, EMG, and ECG were recorded from sleep-deprived subjects exposed to real field driving conditions. A number of severe driving errors occurred during the experiments. The analysis was performed in two main dimensions: the macroscopic analysis that estimates the on-going temporal evolution of physiological measurements during the driving task, and the microscopic event analysis that focuses on the physiological measurements' alterations just before, during, and after the driving errors. Two independent neurophysiologists visually interpreted the measurements. The EEG data were analyzed by using both linear and non-linear analysis tools. We observed the occurrence of brief paroxysmal bursts of alpha activity and an increased synchrony among EEG channels before the driving errors. The alpha relative band ratio (RBR) significantly increased, and the Cross Approximate Entropy that quantifies the synchrony among channels also significantly decreased before the driving errors. Quantitative EEG analysis revealed significant variations of RBR by driving time in the frequency bands of delta, alpha, beta, and gamma. Most of the estimated EEG statistics, such as the Shannon Entropy, Kullback-Leibler Entropy, Coherence, and Cross-Approximate Entropy, were significantly affected by driving time. We also observed an alteration of eyes blinking duration by increased driving time and a significant increase of eye blinks' number and duration before driving errors. EEG and EOG are promising neurophysiological indicators of driver sleepiness and have the potential of monitoring sleepiness in occupational settings incorporated in a sleepiness countermeasure device. The occurrence of brief paroxysmal bursts of alpha activity before severe driving errors is described in detail for the first time. Clear evidence is presented that eye-blinking statistics are sensitive to the driver's sleepiness and should be considered in the design of an efficient and driver-friendly sleepiness detection countermeasure device.

Encouraging full time use of safety belts among current part-time users

DOT National Transportation Integrated Search

1991-01-01

A large percentage of drivers report using their seat belts only some of the time. Most part-time users report they buckle up only for highway driving because they believe that driving around their community does not expose them to a significant risk...

Evaluating driving performance of outpatients with Alzheimer disease.

PubMed

Cox, D J; Quillian, W C; Thorndike, F P; Kovatchev, B P; Hanna, G

1998-01-01

Alzheimer disease (AD) is a progressive disease, with multiple physiologic, psychologic, and social implications. A critical issue in its management is when to recommend restrictions on autonomous functioning, such as driving an automobile. This study evaluates driving performance of patients with AD and its relation to patient scores on the Mini-Mental State Exam (MMSE). This study compared 29 outpatients with probable AD with 21 age-matched control participants on an interactive driving simulator to determine how the two groups differed and how such differences related to mental status. Patients with AD (1) were less likely to comprehend and operate the simulator cognitively, (2) drove off the road more often, (3) spent more time driving considerably slower than the posted speed limit, (4) spent less time driving faster than the speed limit, (5) applied less brake pressure in stop zones, (6) spent more time negotiating left turns, and (7) drove more poorly overall. There were no observed differences between AD patients and the control group in terms of crossing the midline and driving speed variability. Among the AD patients, those who could not drive the simulator because of confusion and disorientation (n = 10) had lower MMSE scores and drove fewer miles annually. Those AD patients who had stopped driving also scored lower on their MMSE but did not perform more poorly on the driving simulator. Factor analysis revealed five driving factors associated with AD, explaining 93 percent of the variance. These five factors correctly classified 27 (85 percent) of 32 AD patients compared with the control group. Of the 15 percent who were improperly classified, there were three false positives (control participants misclassified as AD patients) and two false negatives (AD patients misclassified as control participants). The computed total driving score correlated significantly with MMSE scores (r = -.403, P = 0.011). Driving simulators can provide an objective means of assessing driving safety.

Preclinical Alzheimer's disease and longitudinal driving decline.

PubMed

Roe, Catherine M; Babulal, Ganesh M; Head, Denise M; Stout, Sarah H; Vernon, Elizabeth K; Ghoshal, Nupur; Garland, Brad; Barco, Peggy P; Williams, Monique M; Johnson, Ann; Fierberg, Rebecca; Fague, M Scot; Xiong, Chengjie; Mormino, Elizabeth; Grant, Elizabeth A; Holtzman, David M; Benzinger, Tammie L S; Fagan, Anne M; Ott, Brian R; Carr, David B; Morris, John C

2017-01-01

Links between preclinical AD and driving difficulty onset would support the use of driving performance as an outcome in primary and secondary prevention trials among older adults (OAs). We examined whether AD biomarkers predicted the onset of driving difficulties among OAs. 104 OAs (65+ years) with normal cognition took part in biomarker measurements, a road test, clinical and psychometric batteries and self-reported their driving habits. Higher values of CSF tau/Aβ 42 and ptau 181 /Aβ 42 ratios, but not uptake on PIB amyloid imaging (p=.12), predicted time to a rating of Marginal or Fail on the driving test using Cox proportional hazards models. Hazards ratios (95% confidence interval) were 5.75 (1.70-19.53), p=.005 for CSF tau/Aβ 42 ; 6.19 (1.75-21.88) and p=.005 for CSF ptau 181 /Aβ 42 . Preclinical AD predicted time to receiving a Marginal or Fail rating on an on-road driving test. Driving performance shows promise as a functional outcome in AD prevention trials.

Introducing stochastics into the simulation of convective precipitation events

NASA Astrophysics Data System (ADS)

Pistotnik, Georg

2010-05-01

In a joint project, the Central Institute for Meteorology and Geodynamics (ZAMG) and the Vienna University of Technology aimed to characterize strong precipitation events and their impact in the Bucklige Welt region in Eastern Austria. Both the region's hydrological and meteorological characteristics, namely its composition of virtually countless small catchments with short response times and a high frequency of summertime convective storms, cause the occurrence of flooding to be strictly tied to convective rainfall events, which is why this study has been focused on this type of precipitation. The meteorological database consists of the ZAMG's high-resolution analysis and nowcasting system INCA ("Integrated Nowcasting through Comprehensive Analysis"), which provides a set of precipitation analyses generated by a statistically optimized combination of rain gauge measurements and radar data with a temporal resolution of 15 minutes and a spatial resolution of 1 kilometre. An intensity threshold of 3.8mm/15min has been used to classify any observed precipitation as a convective one, thus extracting 245 convection days with a total number of almost 1600 individual storm events over the project region out of the 5-year data set from 2003 to 2007. Consecutive analyses were used to compute the motion of these storms, a complex process that could not be completely automatized; due to the repeated occurrence of storm splits or coalescences, a manual control of the automatically provided "suggestion" of movement had to be performed in order to merge two or more precipitation maxima to a single storm if necessary, thus yielding the smoothest and most plausible storm tracks and ensuring a high quality of the database. In the first part of the project, distributions for all characteristic parameters have been derived, including the number of storms per day, their place and time of initiation, their motion, lifetime, maximum intensity and maximum "cell volume" (i.e. overall precipitation per time step). Both components of the mean motion as well as of its deviations could be approximated by normal distributions, whereas the number of storms per day, their lifetime, maximum intensity and maximum cell volume roughly followed exponential distributions. The shapes of the convective cells were approximated by Gaussian bells with the peak intensity and the cell volume as boundary conditions. The temporal courses of the peak intensities and cell volumes were assumed to follow parabolas which are symmetric with respect to the half of the lifetime. In the second part of the project, these distributions were used to drive a random generator that allows simulating an arbitrary number of convection days in order to obtain pseudo time series of convective precipitation for each grid point. An algorithm to create correlated samples of random numbers enabled to also account for the observed correlation between some of the parameters, i.e. lifetime and maximum intensity or maximum cell volume. The spatial structures of the return periods of simulated convective precipitation events may provide valuable additional information when being assimilated to the time series measured by the (unfortunately rather sparse) rain gauges in this region. Thus, further studies have to investigate to what extent the "convection simulator" is able to reproduce these time series. Some iterative fine-tuning of the parameters' distributions as well as an extension of the database to a longer time span may further improve the results and enable to simulate realistic spatio-temporal convection scenarios ("design storms") that have the potential to feed hydrological models and, together with vegetation and soil characteristics, hopefully enable to better assess and regionalize the torrent hazard over the project region.

Microprocessor control of photovoltaic systems

NASA Technical Reports Server (NTRS)

Millner, A. R.; Kaufman, D. L.

1984-01-01

The present low power CMOS microprocessor controller for photovoltaic power systems possesses three programs, which are respectively intended for (1) conventional battery-charging systems with state-of-charge estimation and sequential shedding of subarrays and loads, (2) maximum power-controlled battery-charging systems, and (3) variable speed dc motor drives. Attention is presently given to the development of this terrestrial equipment for spacecraft use.

Sodium triflate decreases interaggregate repulsion and induces phase separation in cationic micelles.

PubMed

Lima, Filipe S; Cuccovia, Iolanda M; Buchner, Richard; Antunes, Filipe E; Lindman, Björn; Miguel, Maria G; Horinek, Dominik; Chaimovich, Hernan

2015-03-10

Dodecyltrimethylammonium triflate (DTATf) micelles possess lower degree of counterion dissociation (α), lower hydration, and higher packing of monomers than other micelles of similar structure. Addition of sodium triflate ([NaTf] > 0.05 M) to DTATf solutions promotes phase separation. This phenomenon is commonly observed in oppositely charged surfactant mixtures, but it is rare for ionic surfactants and relatively simple counterions. While the properties of DTATf have already been reported, the driving forces for the observed phase separation with added salt remain unclear. Thus, we propose an interpretation for the observed phase separation in cationic surfactant solutions. Addition of up to 0.03 M NaTf to micellar DTATf solutions led to a limited increase of the aggregation number, to interface dehydration, and to a progressive decrease in α. The viscosity of DTATf solutions of higher concentration ([DTATf] ≥ 0.06 M) reached a maximum with increasing [NaTf], though the aggregation number slightly increased, and no shape change occurred. We hypothesize that this maximum results from a decrease in interaggregate repulsion, as a consequence of increased ion binding. This reduction in micellar repulsion without simultaneous infinite micellar growth is, probably, the major driving force for phase separation at higher [NaTf].

New results on the relation between tyre-road longitudinal stiffness and maximum available grip for motor car

NASA Astrophysics Data System (ADS)

Andrieux, A.; Vandanjon, P. O.; Lengelle, R.; Chabanon, C.

2010-12-01

Tyre-road estimation methods have been the objective of many research programmes throughout the world. Most of these methods aim at estimating the friction components such as tyre longitudinal slip rate κ and friction coefficient μ in the contact patch area. In order to estimate the maximum available friction coefficient μmax, these methods generally use a probabilistic relationship between the grip obtained for low tyre excitations (such as constant speed driving) and the grip obtained for high tyre excitations (such as emergency braking manoeuvre). Confirmation or invalidation of this relationship from experimental results is the purpose of this paper. Experiments have been carried out on a reference track including several test boards corresponding to a wide textural spectrum. The main advantage of these experiments lies in the use of a vehicle allowing us to accurately build point-by-point relationship between κ and μ. This relationship has been determined for different tyres and pavement textures. Finally, the curves obtained are analysed to check the validity of the relationship between the current friction coefficient used by the car during normal driving conditions and μmax.

Quantum resonant activation.

PubMed

Magazzù, Luca; Hänggi, Peter; Spagnolo, Bernardo; Valenti, Davide

2017-04-01

Quantum resonant activation is investigated for the archetype setup of an externally driven two-state (spin-boson) system subjected to strong dissipation by means of both analytical and extensive numerical calculations. The phenomenon of resonant activation emerges in the presence of either randomly fluctuating or deterministic periodically varying driving fields. Addressing the incoherent regime, a characteristic minimum emerges in the mean first passage time to reach an absorbing neighboring state whenever the intrinsic time scale of the modulation matches the characteristic time scale of the system dynamics. For the case of deterministic periodic driving, the first passage time probability density function (pdf) displays a complex, multipeaked behavior, which depends crucially on the details of initial phase, frequency, and strength of the driving. As an interesting feature we find that the mean first passage time enters the resonant activation regime at a critical frequency ν^{*} which depends very weakly on the strength of the driving. Moreover, we provide the relation between the first passage time pdf and the statistics of residence times.

Quantum resonant activation

NASA Astrophysics Data System (ADS)

Magazzó, Luca; Hänggi, Peter; Spagnolo, Bernardo; Valenti, Davide

2017-04-01

Quantum resonant activation is investigated for the archetype setup of an externally driven two-state (spin-boson) system subjected to strong dissipation by means of both analytical and extensive numerical calculations. The phenomenon of resonant activation emerges in the presence of either randomly fluctuating or deterministic periodically varying driving fields. Addressing the incoherent regime, a characteristic minimum emerges in the mean first passage time to reach an absorbing neighboring state whenever the intrinsic time scale of the modulation matches the characteristic time scale of the system dynamics. For the case of deterministic periodic driving, the first passage time probability density function (pdf) displays a complex, multipeaked behavior, which depends crucially on the details of initial phase, frequency, and strength of the driving. As an interesting feature we find that the mean first passage time enters the resonant activation regime at a critical frequency ν* which depends very weakly on the strength of the driving. Moreover, we provide the relation between the first passage time pdf and the statistics of residence times.

Cell phone use while driving and attributable crash risk.

PubMed

Farmer, Charles M; Braitman, Keli A; Lund, Adrian K

2010-10-01

Prior research has estimated that crash risk is 4 times higher when talking on a cell phone versus not talking. The objectives of this study were to estimate the extent to which drivers talk on cell phones while driving and to compute the implied annual number of crashes that could have been avoided if driver cell phone use were restricted. A national survey of approximately 1200 U.S. drivers was conducted. Respondents were asked to approximate the amount of time spent driving during a given day, number of cell phone calls made or received, and amount of driving time spent talking on a cell phone. Population attributable risk (PAR) was computed for each combination of driver gender, driver age, day of week, and time of day. These were multiplied by the corresponding crash counts to estimate the number of crashes that could have been avoided. On average, drivers were talking on cell phones approximately 7 percent of the time while driving. Rates were higher on weekdays (8%), in the afternoon and evening (8%), and for drivers younger than 30 (16%). Based on these use rates, restricting cell phones while driving could have prevented an estimated 22 percent (i.e., 1.3 million) of the crashes in 2008. Although increased rates of cell phone use while driving should be leading to increased crash rates, crash rates have been declining. Reasons for this paradox are unclear. One possibility is that the increase in cell phone use and crash risk due to cell phone use have been overestimated. Another possibility is that cell phone use has supplanted other driving distractions that were similarly hazardous.

Impact of distraction on the driving performance of adolescents with and without attention-deficit/hyperactivity disorder.

PubMed

Narad, Megan; Garner, Annie A; Brassell, Anne A; Saxby, Dyani; Antonini, Tanya N; O'Brien, Kathleen M; Tamm, Leanne; Matthews, Gerald; Epstein, Jeffery N

2013-10-01

This study extends the literature regarding attention-deficit/hyperactivity disorder (ADHD)-related driving impairments to a newly licensed, adolescent population. To investigate the combined risks of adolescence, ADHD, and distracted driving (cell phone conversation and text messaging) on driving performance. Adolescents aged 16 to 17 years with (n = 28) and without (n = 33) ADHD engaged in a simulated drive under 3 conditions (no distraction, cell phone conversation, and texting). During each condition, one unexpected event (eg, another car suddenly merging into driver's lane) was introduced. Cell phone conversation, texting, and no distraction while driving. Self-report of driving history, average speed, standard deviation of speed, standard deviation of lateral position, and braking reaction time during driving simulation. Adolescents with ADHD reported fewer months of driving experience and a higher proportion of driving violations than control subjects. After controlling for months of driving history, adolescents with ADHD demonstrated more variability in speed and lane position than control subjects. There were no group differences for braking reaction time. Furthermore, texting negatively impacted the driving performance of all participants as evidenced by increased variability in speed and lane position. To our knowledge, this study is one of the first to investigate distracted driving in adolescents with ADHD and adds to a growing body of literature documenting that individuals with ADHD are at increased risk for negative driving outcomes. Furthermore, texting significantly impairs the driving performance of all adolescents and increases existing driving-related impairment in adolescents with ADHD, highlighting the need for education and enforcement of regulations against texting for this age group.

A method to estimate the environmental impact of an electric city car during six months of testing in an Italian city

NASA Astrophysics Data System (ADS)

Donateo, T.; Ingrosso, F.; Licci, F.; Laforgia, D.

2014-12-01

The present investigation describes the results of a research project (P.R.I.M.E.) aimed at testing the performance and the environmental impact of an electric city car in Italian cities. The vehicle considered in the project is the Daimler AG Smart ForTwo Electric Drive. A Smart ED vehicle was tested at the University of Salento for six months over different driving conditions (routes, traffic, use of auxiliaries). A data acquisition system has been designed on purpose and assembled on board to provide information about driving cycle and energy flows. The system was also used to evaluate the losses of energy during recharges due to the battery cooling system. The experimental tests were used to identify the average, minimum and maximum consumption of electricity in the Smart ED in Lecce according to driving conditions and in particular according to the usage of auxiliaries. The measured data of electric consumption have been used to quantify the emissions of CO2 and pollution of the vehicle using information about the Italian electricity production mix of each recharging event and the emissions factors of the Italian power plants with an innovative and comprehensive methodology.

Stabilizing effect of driving and dissipation on quantum metastable states

NASA Astrophysics Data System (ADS)

Valenti, Davide; Carollo, Angelo; Spagnolo, Bernardo

2018-04-01

We investigate how the combined effects of strong Ohmic dissipation and monochromatic driving affect the stability of a quantum system with a metastable state. We find that, by increasing the coupling with the environment, the escape time makes a transition from a regime in which it is substantially controlled by the driving, displaying resonant peaks and dips, to a regime of frequency-independent escape time with a peak followed by a steep falloff. The escape time from the metastable state has a nonmonotonic behavior as a function of the thermal-bath coupling, the temperature, and the frequency of the driving. The quantum noise-enhanced stability phenomenon is observed in the investigated system.

Brief Rewarming Blunts Hypothermia-Induced Alterations in Sensation, Motor Drive and Cognition

PubMed Central

Brazaitis, Marius; Paulauskas, Henrikas; Skurvydas, Albertas; Budde, Henning; Daniuseviciute, Laura; Eimantas, Nerijus

2016-01-01

Background: It is well known that cold exposure experienced during occupational or recreational activities may adversely affect motor, cognitive performance, and health. Most research has used prolonged passive external rewarming modalities and focused on the direct effects on the kinetics of physiological and psychological responses in hypothermic subjects. However, the brief whole body rewarming effects on physiological and psychological responses in parallel with functional consequences on cognitive and neurophysiological functions have not been investigated. This study explores these effects in 12 healthy young men. Methods: Subjects (20 ± 1 years) participated in 4 randomized trials, which were designed to compare the effects of whole-body brief (5-min) rewarming in 37°C water with rewarming for the same duration in 24°C (air) thermoneutral environment in mildly hypothermic subjects. After each rewarming, indicators of neuromuscular function (reflexes, central activation ratio, electromyography of exercising muscle, and contractile properties of calf muscles) and cognitive function (attention, simple motor speed, and information processing speed) were assessed. Results: Compared to rewarming in thermoneutral environment, after brief rewarming in 37°C water, significantly lower metabolic heat production (MHP) (206 ± 33.4 vs. 121.9 ± 24.3 W·m2, P < 0.01), heart rate (76 ± 16 vs. 60 ± 12 b·min−1, P < 0.01), cold strain (6.4 ± 3.1 vs. 5.3 ± 2.7, P < 0.01), improved thermal comfort and induced cessation of shivering were found. Electrically induced maximum torque amplitudes increased (P100, 102.8 ± 21.3 vs. 109.2 ± 17.5 Nm and PTT100, 83.1 ± 17.1 vs. 92.7 ± 16.0 Nm, P < 0.05), contraction half-relaxation time decreased (599.0 ± 53.8 vs. 589.0 ± 56.3 ms, P < 0.05), and Mmax-wave latency shortened (17.5 ± 2.2 vs. 15.6 ± 2.0 ms, P < 0.05) after 37°C water rewarming. Unlike rewarming in thermoneutral environment, 37°C water rewarming blunted the hypothermia-induced alterations in neural drive transmission (4.3 ± 0.5 vs. 3.4 ± 0.8 mV H-reflex and 4.9 ± 0.2 vs. 4.4 ± 0.4 mV V-wave, P < 0.05), which increased central fatigue during a 2-min maximum load (P < 0.05). Furthermore, only in brief warm water rewarming cerebral alterations were restored to the control level and it was indicated by shortened reaction times (P < 0.05). Conclusions: Brief rewarming in warm water rather than the same duration rewarming in thermoneutral environment blunted the hypothermia-induced alterations for sensation, motor drive, and cognition, despite the fact that rectal and deep muscle temperature remained lowered. PMID:27990123

Increased parent limits on teen driving: positive effects from a brief intervention administered at the Motor Vehicle Administration.

PubMed

Simons-Morton, Bruce G; Hartos, Jessica L; Beck, Kenneth H

2004-06-01

The purpose of this study was to determine whether exposure to a brief intervention administered at the Motor Vehicle Administration (MVA) increases parental limits on teen driving. A total of 658 parents and their 16-year-old adolescents were recruited from a local MVA site as adolescents successfully tested for provisional licenses. At the MVA, participating parents completed written surveys about expected teen driving during the 1st month of provisional licensure. One month later, 579 parent-teen dyads completed follow-up telephone interviews about teen driving within the past month. On weeks assigned as intervention, parents were exposed to a video and given the video and a driving agreement to take home. In multivariate linear regression analyses, the results indicated that when controlling for selected demographic and baseline psychosocial variables, intervention parents reported more driving rules, restricted driving, limits for high-speed roads, weekend night restrictions, and overall driving limits than did parents in the control group. When compared to control teens, intervention teens reported more limits on passengers, high-speed roads, and night driving, and on overall driving limits, but there were no differences for overall driving or driving under high-risk conditions. In addition, intervention parents were about 3 times, and intervention teens were about 5 times, more likely than controls to report using a parent-teen driving agreement. These results indicate that brief exposure to intervention at an MVA office may help increase parental limits on teen driving.

Prethermal time crystals in a one-dimensional periodically driven Floquet system

NASA Astrophysics Data System (ADS)

Zeng, Tian-Sheng; Sheng, D. N.

2017-09-01

Motivated by experimental observations of time-symmetry breaking behavior in a periodically driven (Floquet) system, we study a one-dimensional spin model to explore the stability of such Floquet discrete time crystals (DTCs) under the interplay between interaction and the microwave driving. For intermediate interactions and high drivings, from the time evolution of both stroboscopic spin polarization and mutual information between two ends, we show that Floquet DTCs can exist in a prethermal time regime without the tuning of strong disorder. For much weak interactions the system is a symmetry-unbroken phase, while for strong interactions it gives its way to a thermal phase. Through analyzing the entanglement dynamics, we show that large driving fields protect the prethermal DTCs from many-body localization and thermalization. Our results suggest that by increasing the spin interaction, one can drive the experimental system into optimal regime for observing a robust prethermal DTC phase.

Transitionless driving on adiabatic search algorithm

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oh, Sangchul, E-mail: soh@qf.org.qa; Kais, Sabre, E-mail: kais@purdue.edu; Department of Chemistry, Department of Physics and Birck Nanotechnology Center, Purdue University, West Lafayette, Indiana 47907

We study quantum dynamics of the adiabatic search algorithm with the equivalent two-level system. Its adiabatic and non-adiabatic evolution is studied and visualized as trajectories of Bloch vectors on a Bloch sphere. We find the change in the non-adiabatic transition probability from exponential decay for the short running time to inverse-square decay in asymptotic running time. The scaling of the critical running time is expressed in terms of the Lambert W function. We derive the transitionless driving Hamiltonian for the adiabatic search algorithm, which makes a quantum state follow the adiabatic path. We demonstrate that a uniform transitionless driving Hamiltonian,more » approximate to the exact time-dependent driving Hamiltonian, can alter the non-adiabatic transition probability from the inverse square decay to the inverse fourth power decay with the running time. This may open up a new but simple way of speeding up adiabatic quantum dynamics.« less

Driving with a short arm cast in a simulator.

PubMed

Mansour, Damian; Mansour, Kristin Gotaas; Kenny, Benjamin William; Attia, John; Meads, Bryce

2015-12-01

To test the ability to steer in a driving simulator in subjects with a short arm cast. 17 men and 13 women aged 23 to 67 (mean, 37) years who had a valid driver's licence were randomised to the cast-first group (n=16; 7 had the cast on the dominant arm) or the cast-second group (n=14; 8 had the cast on the dominant arm) and drove in a simulator. A short arm plaster-of-Paris cast was applied in a neutral position, allowing free movement of the metacarpophalangeal joints, thumb, and elbow joint. Outcome measures included the number of driving off track instances, the number of crashes, the lap time, and the effect of hand dominance on these parameters. Subjects were asked whether the cast had impeded their steering ability. Subjects with or without a cast were comparable in terms of the number of driving off track instances, number of crashes, and lap time. Compared with no cast, the odds ratio (OR) of a subject in a cast driving off the track was 1.02 (p=0.921) and having a crash was 0.79 (p=0.047). All subjects were 1.23 times more likely to drive off the track in their first lap (OR=2.66, p=0.019). The mean lap time decreased for each consecutive lap from the 2nd to 5th laps. Subjects driving with a cast on the dominant or non-dominant arm were comparable. 26 out of the 30 participants considered that the plaster cast impeded their steering ability. Compared with no cast, driving with a short arm cast did not significantly decrease steering ability in a driving simulator.

Aerojet advanced engine concept

NASA Technical Reports Server (NTRS)

Schoenman, L.

1984-01-01

The future orbit transfer vehicle (OTV) requirements which dictate the need for a highly versatile, highly reliable, reusable propulsion module are discussed. To attain maximum operational economy, space-basing is essential. This requires a reusable, maintenance free engine. The design features of this space based engine are defined. A new engine cycle and its advantages allow all the maintenance goals to be attained. Rubbing contact and interpropellant seals and purges are eliminated when GO2 is used to drive the LO2 pump. The TPA design has only one moving part. The use of both GH2 and GO2 to drive the turbines lowers the turbine temperatures in addition lower GH2 temperatures and pressures improve chamber cooling and longer life. The use of GO2 as a turbine drive fluid is addressed. Space based engines require an integrated control and health monitoring system to improve system reliability and eliminate all scheduled maintenance. It is concluded that all OTV propulsion requirements can be fulfilled with a single engine. The technological developments required to demonstrate that engine are outlined.

Bio-inspired piezoelectric linear motor driven by a single-phase harmonic wave with an asymmetric stator.

PubMed

Pan, Qiaosheng; Miao, Enming; Wu, Bingxuan; Chen, Weikang; Lei, Xiujun; He, Liangguo

2017-07-01

A novel, bio-inspired, single-phase driven piezoelectric linear motor (PLM) using an asymmetric stator was designed, fabricated, and tested to avoid mode degeneracy and to simplify the drive mechanism of a piezoelectric motor. A piezoelectric transducer composed of two piezoelectric stacks and a displacement amplifier was used as the driving element of the PLM. Two simple and specially designed claws performed elliptical motion. A numerical simulation was performed to design the stator and determine the feasibility of the design mechanism of the PLM. Moreover, an experimental setup was built to validate the working principles, as well as to evaluate the performance, of the PLM. The prototype motor outputs a no-load speed of 233.7 mm/s at a voltage of 180 V p-p and a maximum thrust force of 2.3 N under a preload of 10 N. This study verified the feasibility of the proposed design and provided a method to simplify the driving harmonic signal and structure of PLMs.

Estimated time of arrival and debiasing the time saving bias.

PubMed

Eriksson, Gabriella; Patten, Christopher J D; Svenson, Ola; Eriksson, Lars

2015-01-01

The time saving bias predicts that the time saved when increasing speed from a high speed is overestimated, and underestimated when increasing speed from a slow speed. In a questionnaire, time saving judgements were investigated when information of estimated time to arrival was provided. In an active driving task, an alternative meter indicating the inverted speed was used to debias judgements. The simulated task was to first drive a distance at a given speed, and then drive the same distance again at the speed the driver judged was required to gain exactly 3 min in travel time compared with the first drive. A control group performed the same task with a speedometer and saved less than the targeted 3 min when increasing speed from a high speed, and more than 3 min when increasing from a low speed. Participants in the alternative meter condition were closer to the target. The two studies corroborate a time saving bias and show that biased intuitive judgements can be debiased by displaying the inverted speed. Practitioner Summary: Previous studies have shown a cognitive bias in judgements of the time saved by increasing speed. This simulator study aims to improve driver judgements by introducing a speedometer indicating the inverted speed in active driving. The results show that the bias can be reduced by presenting the inverted speed and this finding can be used when designing in-car information systems.

Association between unsafe driving performance and cognitive-perceptual dysfunction in older drivers.

PubMed

Park, Si-Woon; Choi, Eun Seok; Lim, Mun Hee; Kim, Eun Joo; Hwang, Sung Il; Choi, Kyung-In; Yoo, Hyun-Chul; Lee, Kuem Ju; Jung, Hi-Eun

2011-03-01

To find an association between cognitive-perceptual problems of older drivers and unsafe driving performance during simulated automobile driving in a virtual environment. Cross-sectional study. A driver evaluation clinic in a rehabilitation hospital. Fifty-five drivers aged 65 years or older and 48 drivers in their late twenties to early forties. All participants underwent evaluation of cognitive-perceptual function and driving performance, and the results were compared between older and younger drivers. The association between cognitive-perceptual function and driving performance was analyzed. Cognitive-perceptual function was evaluated with the Cognitive Perceptual Assessment for Driving (CPAD), a computer-based assessment tool consisting of depth perception, sustained attention, divided attention, the Stroop test, the digit span test, field dependency, and trail-making test A and B. Driving performance was evaluated with use of a virtual reality-based driving simulator. During simulated driving, car crashes were recorded, and an occupational therapist observed unsafe performances in controlling speed, braking, steering, vehicle positioning, making lane changes, and making turns. Thirty-five older drivers did not pass the CPAD test, whereas all of the younger drivers passed the test. When using the driving simulator, a significantly greater number of older drivers experienced car crashes and demonstrated unsafe performance in controlling speed, steering, and making lane changes. CPAD results were associated with car crashes, steering, vehicle positioning, and making lane changes. Older drivers who did not pass the CPAD test are 4 times more likely to experience a car crash, 3.5 times more likely to make errors in steering, 2.8 times more likely to make errors in vehicle positioning, and 6.5 times more likely to make errors in lane changes than are drivers who passed the CPAD test. Unsafe driving performance and car crashes during simulated driving were more prevalent in older drivers than in younger drivers. Unsafe performance in steering, vehicle positioning, making lane changes, and car crashes were associated with cognitive-perceptual dysfunction. Copyright © 2011 American Academy of Physical Medicine and Rehabilitation. Published by Elsevier Inc. All rights reserved.

EVALUATION OF RANGE ESTIMATES FOR TOYOTA FCHV-ADV UNDER OPEN ROAD DRIVING CONDITIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anton, D.; Wipke, K.; Sprik, S.

2009-07-10

The objective of this evaluation was to independently and objectively verify driving ranges of >400 miles announced by Toyota for its new advanced Fuel Cell Hybrid Vehicle (FCHV-adv) utilizing 70 MPa compressed hydrogen. To accomplish this, participants from both Savannah River National Laboratory (SRNL) and the National Renewable Energy Laboratory (NREL) witnessed and participated in a 2-vehicle evaluation with Toyota Motor Engineering & Manufacturing North America, Inc. (TEMA) over a typical open road route for over 11 hours in one day with all relevant data recorded. SRNL and TEMA first entered into discussions of verifying the range of the advancedmore » Toyota Fuel Cell Hybrid Vehicle (FCHV-adv) in August 2008 resulting from reported 400+ mile range by Toyota. After extended negotiations, a CRADA agreement, SRNS CRADA No. CR-04-003, was signed on May 6, 2009. Subsequently, on June 30, 2009 SRNL and NREL participated in an all-day evaluation of the FCHV-adv with TEMA to determine the real-world driving range of this vehicle through on-road driving on an extended round-trip drive between Torrance and San Diego, California. SRNL and NREL observed the vehicles being refueled at Toyota's headquarters the day before the evaluation in Torrance, CA on June 29. At 8:00 AM on June 30, the vehicles departed Torrance north toward downtown Los Angeles, then west to the Pacific Coast Highway, and down to San Diego. After lunch the vehicles retraced their route back to Torrance. The traffic encountered was much heavier than anticipated, causing the vehicles to not return to Torrance until 9 PM. Each vehicle was driven by the same Toyota driver all day, with one SRNL/NREL observer in each vehicle the entire route. Data was logged by Toyota and analyzed by NREL. The maximum range of the FCHV-adv vehicles was calculated to be 431 miles under these driving conditions. This distance was calculated from the actual range of 331.5 miles during over 11 hours driving, plus 99.5 miles of additional range calculated from the average fuel economy from the day times the remaining usable hydrogen. Driving range results were independently calculated for each vehicle, and these results averaged together to achieve the final 431-mile range estimate. The uncertainty on these results is relatively low due to eight independent measurements of distance and six separate measurements of hydrogen usage, with a resulting uncertainty of {+-} 7 miles ({+-} 1.7%) based on spread between the low and high values from all of the multiple measurements. The average fuel economy resulting from the day's driving was 68.3 miles/kg and the total hydrogen stored on-board at 70 MPa was calculated to be 6.31 kg. The speed profiles were analyzed and compared to standard driving cycles, and were determined to be of moderate aggressiveness. The city segments of the route had average speeds slightly greater than the UDDS cycle and the highway segments were close to the HWFET & US06 cycles. The average acceleration for the highway driving was very close to the HWFET cycle, and the city portions had average accelerations lower than the UDDS and US06 cycles. We feel that the route accurately reflects realistic driving behaviors in southern California on a typical weekday, and is an appropriate benchmark to use in the verification of a fuel cell vehicle's range.« less

Reticles, write time, and the need for speed

NASA Astrophysics Data System (ADS)

Ackmann, Paul W.; Litt, Lloyd C.; Ning, Guo Xiang

2014-10-01

Historical data indicates reticle write times are increasing node-to-node. The cost of mask sets is increasing driven by the tighter requirements and more levels. The regular introduction of new generations of mask patterning tools with improved performance is unable to fully compensate for the increased data and complexity required. Write time is a primary metric that drives mask fabrication speed. Design (Raw data) is only the first step in the process and many interactions between mask and wafer technology such as OPC used, OPC efficiency for writers, fracture engines, and actual field size used drive total write time. Yield, technology, and inspection rules drive the remaining raw cycle time. Yield can be even more critical for speed of delivery as it drives re-writes and wasted time. While intrinsic process yield is important, repair capability is the reason mask delivery is still able to deliver 100% good reticles to the fab. Advanced nodes utilizing several layers of multiple patterning may require mask writer tool dedication to meet image placement specifications. This will increase the effective mask cycle time for a layer mask set and drive the need for additional mask write capability in order to deliver masks at the rate required by the wafer fab production schedules.

Timing Characterization of Helium-4 Fast Neutron Detector with EJ-309 Organic Liquid Scintillator

NASA Astrophysics Data System (ADS)

Liang, Yinong; Zhu, Ting; Enqvist, Andreas

2018-01-01

Recently, the Helium-4 gas fast neutron scintillation detectors is being used in time-sensitive measurements, such time-of-flight and multiplicity counting. In this paper, a set of time aligned signals was acquired in a coincidence measurement using the Helium-4 gas detectors and EJ-309 liquid scintillators. The high-speed digitizer system is implanted with a trigger moving average window (MAW) unit combing with its constant fraction discriminator (CFD) feature. It can calculate a "time offset" to the timestamp value to get a higher resolution timestamp (up to 50 ps), which is better than the digitizer's time resolution (4 ns) [1]. The digitized waveforms were saved to the computer hard drive and post processed with digital analysis code to determine the difference of their arrival times. The full-width at half-maximum (FWHM) of the Gaussian fit was used as to examine the resolution. For the cascade decay of Cobalt-60 (1.17 and 1.33 MeV), the first version of the Helium-4 detector with two Hamamatsu R580 photomultipliers (PMT) installed at either end of the cylindrical gas chamber (20 cm in length and 4.4 cm in diameter) has a time resolution which is about 3.139 ns FWHM. With improved knowledge of the timing performance, the Helium-4 scintillation detectors are excellent for neutron energy spectrometry applications requiring high temporal and energy resolutions.

The Impact of Distraction on the Driving Performance of Adolescents with and without Attention Deficit Hyperactivity Disorder

PubMed Central

Narad, Megan; Garner, Annie A.; Brassell, Anne A.; Saxby, Dyani; Antonini, Tanya N.; O'Brien, Kathleen M.; Tamm, Leanne; Matthews, Gerald; Epstein, Jeffery N.

2013-01-01

Importance This study extends the literature regarding Attention-Deficit/Hyperactivity Disorder (ADHD) related driving impairments to a newly-licensed, adolescent population. Objective To investigate the combined risks of adolescence, ADHD, and distracted driving (cell phone conversation and text messaging) on driving performance. Design Adolescents with and without ADHD engaged in a simulated drive under three conditions (no distraction, cell phone conversation, texting). During each condition, one unexpected event (e.g., car suddenly merging into driver's lane) was introduced. Setting Driving simulator. Participants Adolescents aged 16–17 with ADHD (n=28) and controls (n=33). Interventions/Main Exposures Cell phone conversation, texting, and no distraction while driving. Outcome Measures Self-report of driving history; Average speed, standard deviation of speed, standard deviation of lateral position, braking reaction time during driving simulation. Results Adolescents with ADHD reported fewer months of driving experience and a higher proportion of driving violations than controls. After controlling for months of driving history, adolescents with ADHD demonstrated more variability in speed and lane position than controls. There were no group differences for braking reaction time. Further, texting negatively impacted the driving performance of all participants as evidenced by increased variability in speed and lane position. Conclusions This study, one of the first to investigate distracted driving in adolescents with ADHD, adds to a growing body of literature documenting that individuals with ADHD are at increased risk for negative driving outcomes. Furthermore, texting significantly impairs the driving performance of all adolescents and increases existing driving-related impairment in adolescents with ADHD, highlighting the need for education and enforcement of regulations against texting for this age group. PMID:23939758

Sequential Dependencies in Driving

ERIC Educational Resources Information Center

Doshi, Anup; Tran, Cuong; Wilder, Matthew H.; Mozer, Michael C.; Trivedi, Mohan M.

2012-01-01

The effect of recent experience on current behavior has been studied extensively in simple laboratory tasks. We explore the nature of sequential effects in the more naturalistic setting of automobile driving. Driving is a safety-critical task in which delayed response times may have severe consequences. Using a realistic driving simulator, we find…

40 CFR 86.235-94 - Dynamometer procedure.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., carbon dioxide, and oxides of nitrogen. (b) As long as an emission sample is not taken, practice runs...) Four-wheel drive vehicles will be tested in a two-wheel drive mode of operation. Full-time four-wheel drive vehicles will have one set of drive wheels temporarily disengaged by the vehicle manufacturer...

Relative benefits of stimulant therapy with OROS methylphenidate versus mixed amphetamine salts extended release in improving the driving performance of adolescent drivers with attention-deficit/hyperactivity disorder.

PubMed

Cox, Daniel J; Merkel, R Lawrence; Moore, Melissa; Thorndike, Frances; Muller, Carrie; Kovatchev, Boris

2006-09-01

Automobile accidents are the leading cause of death among adolescents, and collisions are 2 to 4 times more likely to occur among adolescents with attention-deficit/hyperactivity disorder. Studies have demonstrated that stimulants improve driving performance. This study compared 2 long-acting stimulant medications during daytime and evening driving evaluations. Adolescent drivers with attention-deficit/hyperactivity disorder were compared on a driving simulator after taking 72 mg of OROS methylphenidate, 30 mg of mixed amphetamine salts extended release, or placebo in a randomized, double-blind, placebo-controlled, crossover study design. During laboratory testing, adolescents drove a driving simulator at 5:00 pm, 8:00 pm, and 11:00 pm. Driving performance was rated by adolescents and investigators. The study included 35 adolescent drivers with attention-deficit/hyperactivity disorder (19 boys/16 girls). The mean age was 17.8 years. The overall Impaired Driving Score demonstrated that OROS methylphenidate led to better driving performance compared with placebo and mixed amphetamine salts extended release, whereas mixed amphetamine salts extended release demonstrated no statistical improvement over placebo. Specifically, relative to placebo, OROS methylphenidate resulted in less time driving off the road, fewer instances of speeding, less erratic speed control, more time executing left turns, and less inappropriate use of brakes. OROS methylphenidate and mixed amphetamine salts extended release worked equally well for male and female adolescents and equally as well with teenagers who have combined and inattentive subtypes of attention-deficit/hyperactivity disorder. This study validates the use of stimulants to improve driving performance in adolescents with attention-deficit/hyperactivity disorder. In the study, OROS methylphenidate promoted significantly improved driving performance compared with placebo and mixed amphetamine salts extended release.

Phase-locking transition in a chirped superconducting Josephson resonator.

PubMed

Naaman, O; Aumentado, J; Friedland, L; Wurtele, J S; Siddiqi, I

2008-09-12

We observe a sharp threshold for dynamic phase locking in a high-Q transmission line resonator embedded with a Josephson tunnel junction, and driven with a purely ac, chirped microwave signal. When the drive amplitude is below a critical value, which depends on the chirp rate and is sensitive to the junction critical current I0, the resonator is only excited near its linear resonance frequency. For a larger amplitude, the resonator phase locks to the chirped drive and its amplitude grows until a deterministic maximum is reached. Near threshold, the oscillator evolves smoothly in one of two diverging trajectories, providing a way to discriminate small changes in I0 with a nonswitching detector, with potential applications in quantum state measurement.

Convergent ablation measurements of plastic ablators in gas-filled rugby hohlraums on OMEGA

NASA Astrophysics Data System (ADS)

Casner, A.; Jalinaud, T.; Masse, L.; Galmiche, D.

2015-10-01

Indirect-drive implosions experiments were conducted on the Omega Laser Facility to test the performance of uniformly doped plastic ablators for Inertial Confinement Fusion. The first convergent ablation measurements in gas-filled rugby hohlraums are reported. Ignition relevant limb velocities in the range from 150 to 300 μm .n s-1 have been reached by varying the laser drive energy and the initial capsule aspect ratio. The measured capsule trajectory and implosion velocity are in good agreement with 2D integrated simulations and a zero-dimensional modeling of the implosions. We demonstrate experimentally the scaling law for the maximum implosion velocity predicted by the improved rocket model [Y. Saillard, Nucl. Fusion 46, 1017 (2006)] in the high-ablation regime case.

"My Son Is Reliable": Young Drivers' Parents' Optimism and Views on the Norms of Parental Involvement in Youth Driving

ERIC Educational Resources Information Center

Guttman, Nurit

2013-01-01

The high crash rates among teenage drivers are of great concern across nations. Parents' involvement is known to help increase their young drivers' driving safety. In particular, parents can place restrictions on their son's/daughter's driving (e.g., restrict night time driving), which can enable the young driver to gain driving experience in…

Energetic and biomechanical constraints on animal migration distance.

PubMed

Hein, Andrew M; Hou, Chen; Gillooly, James F

2012-02-01

Animal migration is one of the great wonders of nature, but the factors that determine how far migrants travel remain poorly understood. We present a new quantitative model of animal migration and use it to describe the maximum migration distance of walking, swimming and flying migrants. The model combines biomechanics and metabolic scaling to show how maximum migration distance is constrained by body size for each mode of travel. The model also indicates that the number of body lengths travelled by walking and swimming migrants should be approximately invariant of body size. Data from over 200 species of migratory birds, mammals, fish, and invertebrates support the central conclusion of the model - that body size drives variation in maximum migration distance among species through its effects on metabolism and the cost of locomotion. The model provides a new tool to enhance general understanding of the ecology and evolution of migration. © 2011 Blackwell Publishing Ltd/CNRS.

Calculations of the Performance of a Compression-Ignition Engine-Compressor Turbine Combination I : Performance of a Highly Supercharged Compression-Ignition Engine

NASA Technical Reports Server (NTRS)

Sanders, J. C.; Mendelson, Alexander

1945-01-01

Small high-speed single-cylinder compression-ignition engines were tested to determine their performance characteristics under high supercharging. Calculations were made on the energy available in the exhaust gas of the compression-ignition engines. The maximum power at any given maximum cylinder pressure was obtained when the compression pressure was equal to the maximum cylinder pressure. Constant-pressure combustion was found possible at an engine speed of 2200 rpm. Exhaust pressures and temperatures were determined from an analysis of indicator cards. The analysis showed that, at rich mixtures with the exhaust back pressure equal to the inlet-air pressure, there is excess energy available for driving a turbine over that required for supercharging. The presence of this excess energy indicates that a highly supercharged compression-ignition engine might be desirable as a compressor and combustion chamber for a turbine.

The relations between driving behavior, physical activity and weight status among Canadian adults.

PubMed

Swanson, Kenda C; McCormack, Gavin R

2012-03-01

Evidence regarding the relative contributions of physical activity (PA) and driving behavior on weight status is limited. This study examined the associations between driving and PA behavior and weight status among Canadian adults. A random cross-section of Calgarian adults (n = 1026) completed a telephone-interview and a self-administered questionnaire. Weekly physical activity time, daily driving time, BMI, motor vehicle access, and demographic characteristics were captured. Logistic regression was used to estimate associations between driving minutes (0-209, 219-419, 420-839, 840-1679, and ≥ 1680 min/week), motor vehicle access, sufficient PA (210 min/week of moderate-intensity PA or 90 min/week of vigorous-intensity PA), and the likelihood of being 1) overweight/obese vs. healthy weight and 2) obese only vs. healthy/overweight. Compared with driving ≤ 209 min/week, driving 840 to 1679 min/week significantly (P < .05) increased the likelihood of being overweight/obese (OR 2.08). Insufficient PA was positively associated with being overweight/obese (OR 1.43). Each hour/week of driving was associated with a 1.6% reduction in the odds of achieving sufficient PA. A 3-fold increase (OR 3.73) in the likelihood of overweight was found among insufficiently active individuals who drove 210 to 419 min/week compared with sufficiently active individuals who drove ≤ 209 min/week. Interventions that decrease driving time and increase PA participation may be important for reducing weight among Canadian adults.

Effects of oxygen concentrations on driver fatigue during simulated driving.

PubMed

Sung, Eun-Jung; Min, Byung-Chan; Kim, Seung-Chul; Kim, Chul-Jung

2005-01-01

Driver fatigue has been the cause of traffic accidents. Despite this, the amount of time that drivers spend within cars has been increasing due to complex city life, traffic congestion, and particular occupational requirements. Consequently, fatigue and stress cannot be avoided. In present study, in order to find out the possibility for reducing fatigue while driving due to the supply of oxygen, driver fatigue resulting from the passage of time when different oxygen concentrations are supplied has been examined through subjective evaluations and reaction times using driving simulator for 10 male subjects. The results revealed the subjective fatigue feeling was highest in the low rate (18%) oxygen condition, while in the high rate (30%), it decreased to a certain extent. The feeling of sleepiness also showed the tendency to decrease somewhat in the case of the driving time having passed over 1h in the high-rate conditions. Also, the reaction time for braking after being instructed to suddenly stop following more than 2h of driving was reduced in the high-rate oxygen conditions compared to the low-rate oxygen condition. From the above results, it was shown that while driving a car, if the oxygen rate is lowered, fatigue is felt severely, and that in the case of supplying a high-rate of oxygen, the feeling of fatigue is lowered to some extent and the reaction time is shortened. It was suggested that the driver's fatigue can be reduced according to the supply of oxygen.

Lower hybrid accessibility in a large, hot reversed field pinch

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dziubek, R.A.

1995-02-01

Recent theoretical and experimental results indicate that driving a current in the outer radius of an RPF suppresses sawtooth activity and increases particle and energy confinement times. One candidate for a form of steady state current drive is the slow wave at the lower hybrid frequency. Here, the accessibility of such a wave in an RFP plasma is investigated theoretically, with focus on the RFX machine of Padua, Italy. To drive current, the slow wave with frequency between 1.0--1.5 GHz is considered where optimal Landau damping is desired at r/a {approximately} 0.7. By numerically determining the values of the wave`smore » perpendicular index of refraction which satisfy the hot plasma dispersion relation, regions of propagation and evanescence can be found. The path of the wave can then be traced over a contour map of these regions so that accessibility can be clearly seen. The possibility of mode conversion events can be ascertained by plotting the values of the perpendicular index of refraction for the fast and slow wave and observing convergence points. To locate regions of maximum Landau damping, a technique developed by Stix was adapted for use with the slow wave in an RFP plasma. Results show that the slow wave is accessible to the target region without mode conversion so long as the value of the parallel index of refraction is correctly chosen at the edge of the plasma. Landau damping can also be optimized with this method. In an RFP, 2--20% of the electron population consists of fast electrons. Because this species alters the total electron distribution function and raises the effective temperature in the outer regions of the plasma, its presence is expected to shift the location of ideal Landau damping.« less

Evaluation of Fairchild's Gate Drive Optocoupler, Type FOD3150, Under Wide Temperature Operation

NASA Technical Reports Server (NTRS)

Patterson, Richard; Hammoud, Adhad; Panko, Scott

2010-01-01

An optocoupler is a semiconductor device that is used to transfer a signal between different parts of a circuit that need to be electrically isolated from one another - for example, where a high voltage is to be switched with a low voltage control signal. Optocouplers often can be used in place of relays. These optocouplers utilize an infrared LED (light emitting diode) and a photodetector such as a silicon controlled rectifier or photosensitive silicon diode for the transfer of the electronic signal between components of a circuit by means of a short optical transmission channel. For maximum coupling, the wave-length responses of the LED and the detector should be very similar. In switch-mode power supply applications, optocouplers offer advantages over transformers by virtue of simpler circuit design, reduced weight, and DC coupling capability. The effects of extreme temperature exposure and thermal cycling on the performance of a commercial-off-the-shelf (COTS) optocoupler, Fairchild FOD3150, were evaluated in this work. This 1.0 A output current, high noise immunity gate drive optocoupler utilizes an aluminum gallium arsenide (AlGaAs) LED, is capable of driving most 800V/20A IGBT/MOSFETs, and is suited for fast switching in motor control inverter applications and high performance power systems. Some of the specifications of the isolator chip are listed. The device was evaluated in terms of output response, output rise (t(sub r)) and fall times (t(sub f)), and propagation delays (using a 50% level between input and output during low to high (t(sub PLH)) and high to low (t(sub PLH)) transitions). The output supply current was also obtained. These parameters were recorded at various test temperatures between -190 C and +110 C.

Relationship of impaired-driving enforcement intensity to drinking and driving on the roads.

PubMed

Fell, James C; Waehrer, Geetha; Voas, Robert B; Auld-Owens, Amy; Carr, Katherine; Pell, Karen

2015-01-01

It is principally the area of enforcement that offers the greatest opportunity for reducing alcohol-impaired driving in the near future. How much of a reduction in drinking and driving would be achieved by how much improvement in enforcement intensity? We developed logistic regression models to explore how enforcement intensity (6 different measures) related to the prevalence of weekend nighttime drivers in the 2007 National Roadside Survey who had been drinking (blood alcohol concentration [BAC] ≥ 0.00 g/dl), who had BACs ≥ 0.05 g/dl, and who were driving with an illegal BAC ≥ 0.08 g/dl. Drivers on the roads in our sample of 30 communities who were exposed to fewer than 228 traffic stops per 10,000 population aged 18 and older had 2.4 times the odds of being BAC positive, 3.6 times the odds of driving with a BAC ≥ 0.05, and 3.8 times the odds of driving with a BAC ≥ 0.08 compared to those drivers on the roads in communities with more than 1,275 traffic stops per 10,000 population. Drivers on the roads in communities with fewer than 3.7 driving under the influence (DUI) arrests per 10,000 population had 2.7 times the odds of BAC-positive drivers on the roads compared to communities with the highest intensity of DUI arrest activity (>38 DUI arrests per 10,000 population). The number of traffic stops and DUI arrests per capita were significantly associated with the odds of drinking and driving on the roads in these communities. This might reflect traffic enforcement visibility. The findings in this study may help law enforcement agencies around the country adjust their traffic enforcement intensity to reduce impaired driving in their community. Copyright © 2014 by the Research Society on Alcoholism.

Driving context influences drivers' decision to engage in visual-manual phone tasks: Evidence from a naturalistic driving study.

PubMed

Tivesten, Emma; Dozza, Marco

2015-06-01

Visual-manual (VM) phone tasks (i.e., texting, dialing, reading) are associated with an increased crash/near-crash risk. This study investigated how the driving context influences drivers' decisions to engage in VM phone tasks in naturalistic driving. Video-recordings of 1,432 car trips were viewed to identify VM phone tasks and passenger presence. Video, vehicle signals, and map data were used to classify driving context (i.e., curvature, other vehicles) before and during the VM phone tasks (N=374). Vehicle signals (i.e., speed, yaw rate, forward radar) were available for all driving. VM phone tasks were more likely to be initiated while standing still, and less likely while driving at high speeds, or when a passenger was present. Lead vehicle presence did not influence how likely it was that a VM phone task was initiated, but the drivers adjusted their task timing to situations when the lead vehicle was increasing speed, resulting in increasing time headway. The drivers adjusted task timing until after making sharp turns and lane change maneuvers. In contrast to previous driving simulator studies, there was no evidence of drivers reducing speed as a consequence of VM phone task engagement. The results show that experienced drivers use information about current and upcoming driving context to decide when to engage in VM phone tasks. However, drivers may fail to sufficiently increase safety margins to allow time to respond to possible unpredictable events (e.g., lead vehicle braking). Advanced driver assistance systems should facilitate and possibly boost drivers' self-regulating behavior. For instance, they might recognize when appropriate adaptive behavior is missing and advise or alert accordingly. The results from this study could also inspire training programs for novice drivers, or locally classify roads in terms of the risk associated with secondary task engagement while driving. Copyright © 2015. Published by Elsevier Ltd.

Passive Assessment of Routine Driving with Unobtrusive Sensors: A New Approach for Identifying and Monitoring Functional Level in Normal Aging and Mild Cognitive Impairment

PubMed Central

Seelye, Adriana; Mattek, Nora; Sharma, Nicole; Witter, Phelps; Brenner, Ariella; Wild, Katherine; Dodge, Hiroko; Kaye, Jeffrey

2017-01-01

Background Driving is a key functional activity for many older adults, and changes in routine driving may be associated with emerging cognitive decline due to early neurodegenerative disease. Current methods for assessing driving such as self-report are inadequate for identifying and monitoring subtle changes in driving patterns that may be the earliest signals of functional change in developing mild cognitive impairment (MCI). Objective This proof of concept study aimed to establish the feasibility of continuous driving monitoring in a sample of cognitively normal and MCI older adults for an average of 206 days using an unobtrusive driving sensor and demonstrate that derived sensor-based driving metrics could effectively discriminate between MCI and cognitively intact groups. Methods Novel objective driving measures derived from 6 months of routine driving monitoring were examined in older adults with intact cognition (n = 21) and MCI (n = 7) who were enrolled in the Oregon Center for Aging and Technology (ORCATECH) longitudinal assessment program. Results Unobtrusive continuous monitoring of older adults’ routine driving using a driving sensor was feasible and well accepted. MCI participants drove fewer miles and spent less time on the highway per day than cognitively intact participants. MCI drivers showed less day-to-day fluctuations in their driving habits than cognitively intact drivers. Conclusion Sensor-based driving measures are objective, unobtrusive, and can be assessed every time a person drives his or her vehicle to identify clinically meaningful changes in daily driving. This novel methodology has the potential to be useful for the early detection and monitoring of changes in daily functioning within individuals. PMID:28731434

Surface temperatures and glassy state investigations in tribology, part 2

NASA Technical Reports Server (NTRS)

Bair, S. S.; Winer, W. O.

1979-01-01

Measurements of lubricant shear rheological behavior in the amorphous solid region and near the liquid solid transition are reported. Elastic, plastic and viscous behavior was observed. The maximum yield shear stress (limiting shear stress) is a function of temperature and pressure and is believed to be the property which determines the maximum traction in elastohydrodynamic contacts such as traction drives. A shear rheological model based on primary laboratory data is proposed for concentrated contact lubrication. The model is Maxwell model modified with a limiting shear stress. Three material properties are required: low shear stress viscosity, limiting elastic shear modulus, and the limiting shear stress the material can withstand. All three are functions of temperature and pressure.

77 FR 12907 - Visual-Manual NHTSA Driver Distraction Guidelines for In-Vehicle Electronic Devices

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-02

... impact of task performance while driving on driving safety and time-based acceptance criteria for... feedback). The proposed NHTSA Guidelines list certain secondary, non-driving related tasks that, based on... cannot be used by the driver to perform such tasks while the driver is driving. For all other secondary...

Continued Driving and Time to Transition to Nondriver Status through Error-Specific Driving Restrictions

ERIC Educational Resources Information Center

Freund, Barbara; Petrakos, Davithoula

2008-01-01

We developed driving restrictions that are linked to specific driving errors, allowing cognitively impaired individuals to continue to independently meet mobility needs while minimizing risk to themselves and others. The purpose of this project was to evaluate the efficacy and duration expectancy of these restrictions in promoting safe continued…

Trade-off between jerk and time headway as an indicator of driving style

PubMed Central

Pekkanen, Jami; Lappi, Otto; Kosonen, Iisakki; Luttinen, Tapio; Summala, Heikki

2017-01-01

Variation in longitudinal control in driving has been discussed in both traffic psychology and transportation engineering. Traffic psychologists have concerned themselves with “driving style”, a habitual form of behavior marked by it’s stability, and its basis in psychological traits. Those working in traffic microsimulation have searched for quantitative ways to represent different driver-car systems in car following models. There has been unfortunately little overlap or theoretical consistency between these literatures. Here, we investigated relationships between directly observable measures (time headway, acceleration and jerk) in a simulated driving task where the driving context, vehicle and environment were controlled. We found individual differences in the way a trade-off was made between close but jerky vs. far and smooth following behavior. We call these “intensive” and “calm” driving, and suggest this trade-off can serve as an indicator of a possible latent factor underlying driving style. We posit that pursuing such latent factors for driving style may have implications for modelling driver heterogeneity across various domains in traffic simulation. PMID:29040291

Floquet Engineering in Quantum Chains

NASA Astrophysics Data System (ADS)

Kennes, D. M.; de la Torre, A.; Ron, A.; Hsieh, D.; Millis, A. J.

2018-03-01

We consider a one-dimensional interacting spinless fermion model, which displays the well-known Luttinger liquid (LL) to charge density wave (CDW) transition as a function of the ratio between the strength of the interaction U and the hopping J . We subject this system to a spatially uniform drive which is ramped up over a finite time interval and becomes time periodic in the long-time limit. We show that by using a density matrix renormalization group approach formulated for infinite system sizes, we can access the large-time limit even when the drive induces finite heating. When both the initial and long-time states are in the gapless (LL) phase, the final state has power-law correlations for all ramp speeds. However, when the initial and final state are gapped (CDW phase), we find a pseudothermal state with an effective temperature that depends on the ramp rate, both for the Magnus regime in which the drive frequency is very large compared to other scales in the system and in the opposite limit where the drive frequency is less than the gap. Remarkably, quantum defects (instantons) appear when the drive tunes the system through the quantum critical point, in a realization of the Kibble-Zurek mechanism.

Utility Tax Relief Program in the Netherlands

DTIC Science & Technology

2010-01-06

Management Command, Europe Region LQA Living Quarters Allowance VAT Value Added Tax INSPECTOR GENERAL DEPARTMENT OF DEFENSE 400 ARMY NAVY DRIVE...savings on their utility bills. However, for DOD civilians receiving Living Quarters Allowance ( LQA ),2 DOD realizes the cost savings through reduced... LQA payments, unless the civilian’s housing expenses exceed the maximum allowable LQA . 1 For the purpose of this report, DOD personnel refers to

Relationship of Near-Crash/Crash Risk to Time Spent on a Cell Phone While Driving.

PubMed

Farmer, Charles M; Klauer, Sheila G; McClafferty, Julie A; Guo, Feng

2015-01-01

The objective of this study was to examine in a naturalistic driving setting the dose-response relationship between cell phone usage while driving and risk of a crash or near crash. How is the increasing use of cell phones by drivers associated with overall near-crash/crash risk (i.e., during driving times both on and off the phone)? Day-to-day driving behavior of 105 volunteer subjects was monitored over a period of 1 year. A random sample was selected comprised of 4 trips from each month that each driver was in the study, and in-vehicle video was used to classify driver behavior. The proportion of driving time spent using a cell phone was estimated for each 3-month period and correlated with overall crash and near-crash rates for each period. Thus, it was possible to test whether changes in an individual driver's cell phone use over time were associated with changes in overall near-crash/crash risk. Drivers in the study spent 11.7% of their driving time interacting with a cell phone, primarily talking on the phone (6.5%) or simply holding the phone in their hand or lap (3.7%). The risk of a near-crash/crash event was approximately 17% higher when the driver was interacting with a cell phone, due primarily to actions of reaching for/answering/dialing, which nearly triples risk (relative risk = 2.84). However, the amount of driving time spent interacting with a cell phone did not affect a driver's overall near-crash/crash risk. Vehicle speeds within 6 s of the beginning of each call on average were 5-6 mph lower than speeds at other times. Results of this naturalistic driving study are consistent with the observation that increasing cell phone use in the general driving population has not led to increased crash rates. Although cell phone use can be distracting and crashes have occurred during this distraction, overall crash rates appear unaffected by changes in the rate of cell phone use, even for individual drivers. Drivers compensate somewhat for the distraction by conducting some of the more demanding tasks, such as reaching for or dialing a cell phone, at lower speeds. It is also possible that cell phones and other electronic devices in cars are changing how drivers manage their attention to various tasks and/or changing the kinds of secondary tasks in which they engage.

Drinking and driving among high school students.

PubMed

Williams, A F; Lund, A K; Preusser, D F

1986-06-01

A questionnaire survey of high school students conducted in 1983 provided information on their self-reported drinking and driving practices. By age 15 the majority reported drinking alcoholic beverages. By age 17 half or more of the males and one-third of the females reported driving after drinking at least once in the past month. About one-quarter of the students estimated that six or more cans of beer would be required to make someone an unsafe driver. Reported frequency of driving after drinking was associated with less time spent on homework and poorer academic performance, working part time, greater participation in social activities, less perceived parental influence regarding their travel, owning a car, driving high mileage, speeding, and having crashes and violations.

Driving Task: How Older Drivers' On-Road Driving Performance Relates to Abilities, Perceptions, and Restrictions.

PubMed

Koppel, Sjaan; Charlton, Judith L; Langford, Jim; Di Stefano, Marilyn; MacDonald, Wendy; Vlahodimitrakou, Zafiroula; Mazer, Barbara L; Gelinas, Isabelle; Vrkljan, Brenda; Eliasz, Kinga; Myers, Anita; Tuokko, Holly A; Marshall, Shawn C

2016-06-01

This study examined a cohort of 227 older drivers and investigated the relationship between performance on the electronic Driver Observation Schedule (eDOS) driving task and: (1) driver characteristics; (2) functional abilities; (3) perceptions of driving comfort and abilities; and (4) self-reported driving restrictions. Participants (male: 70%; age: M = 81.53 years, SD = 3.37 years) completed a series of functional ability measures and scales on perceived driving comfort, abilities, and driving restrictions from the Year 2 Candrive/Ozcandrive assessment protocol, along with an eDOS driving task. Observations of participants' driving behaviours during the driving task were recorded for intersection negotiation, lane-changing, merging, low-speed maneuvers, and maneuver-free driving. eDOS driving task scores were high (M = 94.74; SD = 5.70) and significantly related to participants' perceived driving abilities, reported frequency of driving in challenging situations, and number of driving restrictions. Future analyses will explore potential changes in driving task scores over time.

Uncertainty and feasibility of dynamical downscaling for modeling tropical cyclones for storm surge simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Zhaoqing; Taraphdar, Sourav; Wang, Taiping

This paper presents a modeling study conducted to evaluate the uncertainty of a regional model in simulating hurricane wind and pressure fields, and the feasibility of driving coastal storm surge simulation using an ensemble of region model outputs produced by 18 combinations of three convection schemes and six microphysics parameterizations, using Hurricane Katrina as a test case. Simulated wind and pressure fields were compared to observed H*Wind data for Hurricane Katrina and simulated storm surge was compared to observed high-water marks on the northern coast of the Gulf of Mexico. The ensemble modeling analysis demonstrated that the regional model wasmore » able to reproduce the characteristics of Hurricane Katrina with reasonable accuracy and can be used to drive the coastal ocean model for simulating coastal storm surge. Results indicated that the regional model is sensitive to both convection and microphysics parameterizations that simulate moist processes closely linked to the tropical cyclone dynamics that influence hurricane development and intensification. The Zhang and McFarlane (ZM) convection scheme and the Lim and Hong (WDM6) microphysics parameterization are the most skillful in simulating Hurricane Katrina maximum wind speed and central pressure, among the three convection and the six microphysics parameterizations. Error statistics of simulated maximum water levels were calculated for a baseline simulation with H*Wind forcing and the 18 ensemble simulations driven by the regional model outputs. The storm surge model produced the overall best results in simulating the maximum water levels using wind and pressure fields generated with the ZM convection scheme and the WDM6 microphysics parameterization.« less

Global conditions in the solar corona from 2010 to 2017

PubMed Central

Morgan, Huw; Taroyan, Youra

2017-01-01

Through reduction of a huge data set spanning 2010–2017, we compare mean global changes in temperature, emission measure (EM), and underlying photospheric magnetic field of the solar corona over most of the last activity cycle. The quiet coronal mean temperature rises from 1.4 to 1.8 MK, whereas EM increases by almost a factor of 50% from solar minimum to maximum. An increased high-temperature component near 3 MK at solar maximum drives the increase in quiet coronal mean temperature, whereas the bulk of the plasma remains near 1.6 MK throughout the cycle. The mean, spatially smoothed magnitude of the quiet Sun magnetic field rises from 1.6 G in 2011 to peak at 2.0 G in 2015. Active region conditions are highly variable, but their mean remains approximately constant over the cycle, although there is a consistent decrease in active region high-temperature emission (near 3 MK) between the peak of solar maximum and present. Active region mean temperature, EM, and magnetic field magnitude are highly correlated. Correlation between sunspot/active region area and quiet coronal conditions shows the important influence of decaying sunspots in driving global changes, although we find no appreciable delay between changes in active region area and quiet Sun magnetic field strength. The hot coronal contribution to extreme ultraviolet (EUV) irradiance is dominated by the quiet corona throughout most of the cycle, whereas the high variability is driven by active regions. Solar EUV irradiance cannot be predicted accurately by sunspot index alone, highlighting the need for continued measurements. PMID:28740861

The Maximum Flux of Star-Forming Galaxies

NASA Astrophysics Data System (ADS)

Crocker, Roland M.; Krumholz, Mark R.; Thompson, Todd A.; Clutterbuck, Julie

2018-04-01

The importance of radiation pressure feedback in galaxy formation has been extensively debated over the last decade. The regime of greatest uncertainty is in the most actively star-forming galaxies, where large dust columns can potentially produce a dust-reprocessed infrared radiation field with enough pressure to drive turbulence or eject material. Here we derive the conditions under which a self-gravitating, mixed gas-star disc can remain hydrostatic despite trapped radiation pressure. Consistently taking into account the self-gravity of the medium, the star- and dust-to-gas ratios, and the effects of turbulent motions not driven by radiation, we show that galaxies can achieve a maximum Eddington-limited star formation rate per unit area \\dot{Σ }_*,crit ˜ 10^3 M_{⊙} pc-2 Myr-1, corresponding to a critical flux of F*, crit ˜ 1013L⊙ kpc-2 similar to previous estimates; higher fluxes eject mass in bulk, halting further star formation. Conversely, we show that in galaxies below this limit, our one-dimensional models imply simple vertical hydrostatic equilibrium and that radiation pressure is ineffective at driving turbulence or ejecting matter. Because the vast majority of star-forming galaxies lie below the maximum limit for typical dust-to-gas ratios, we conclude that infrared radiation pressure is likely unimportant for all but the most extreme systems on galaxy-wide scales. Thus, while radiation pressure does not explain the Kennicutt-Schmidt relation, it does impose an upper truncation on it. Our predicted truncation is in good agreement with the highest observed gas and star formation rate surface densities found both locally and at high redshift.

The maximum flux of star-forming galaxies

NASA Astrophysics Data System (ADS)

Crocker, Roland M.; Krumholz, Mark R.; Thompson, Todd A.; Clutterbuck, Julie

2018-07-01

The importance of radiation pressure feedback in galaxy formation has been extensively debated over the last decade. The regime of greatest uncertainty is in the most actively star-forming galaxies, where large dust columns can potentially produce a dust-reprocessed infrared radiation field with enough pressure to drive turbulence or eject material. Here, we derive the conditions under which a self-gravitating mixed gas-star disc can remain hydrostatic despite trapped radiation pressure. Consistently, taking into account the self-gravity of the medium, the star- and dust-to-gas ratios, and the effects of turbulent motions not driven by radiation, we show that galaxies can achieve a maximum Eddington-limited star formation rate per unit area \\dot{Σ }_*,crit ˜ 10^3 M_{⊙} pc-2 Myr-1, corresponding to a critical flux of F*,crit ˜ 1013 L⊙ kpc-2 similar to previous estimates; higher fluxes eject mass in bulk, halting further star formation. Conversely, we show that in galaxies below this limit, our 1D models imply simple vertical hydrostatic equilibrium and that radiation pressure is ineffective at driving turbulence or ejecting matter. Because the vast majority of star-forming galaxies lie below the maximum limit for typical dust-to-gas ratios, we conclude that infrared radiation pressure is likely unimportant for all but the most extreme systems on galaxy-wide scales. Thus, while radiation pressure does not explain the Kennicutt-Schmidt relation, it does impose an upper truncation on it. Our predicted truncation is in good agreement with the highest observed gas and star formation rate surface densities found both locally and at high redshift.

Comparison of SAR and induced current densities in adults and children exposed to electromagnetic fields from electronic article surveillance devices

NASA Astrophysics Data System (ADS)

Martínez-Búrdalo, M.; Sanchis, A.; Martín, A.; Villar, R.

2010-02-01

Electronic article surveillance (EAS) devices are widely used in most stores as anti-theft systems. In this work, the compliance with international guidelines in the human exposure to these devices is analysed by using the finite-difference time-domain (FDTD) method. Two sets of high resolution numerical phantoms of different size (REMCOM/Hershey and Virtual Family), simulating adult and child bodies, are exposed to a 10 MHz pass-by panel-type EAS consisting of two overlapping current-carrying coils. Two different relative positions between the EAS and the body (frontal and lateral exposures), which imply the exposure of different parts of the body at different distances, have been considered. In all cases, induced current densities in tissues of the central nervous system and specific absorption rates (SARs) are calculated to be compared with the limits from the guidelines. Results show that induced current densities are lower in the case of adult models as compared with those of children in both lateral and frontal exposures. Maximum SAR values calculated in lateral exposure are significantly lower than those calculated in frontal exposure, where the EAS-body distance is shorter. Nevertheless, in all studied cases, with an EAS driving current of 4 A rms, maximum induced current and SAR values are below basic restrictions.

Comparison of SAR and induced current densities in adults and children exposed to electromagnetic fields from electronic article surveillance devices.

PubMed

Martínez-Búrdalo, M; Sanchis, A; Martín, A; Villar, R

2010-02-21

Electronic article surveillance (EAS) devices are widely used in most stores as anti-theft systems. In this work, the compliance with international guidelines in the human exposure to these devices is analysed by using the finite-difference time-domain (FDTD) method. Two sets of high resolution numerical phantoms of different size (REMCOM/Hershey and Virtual Family), simulating adult and child bodies, are exposed to a 10 MHz pass-by panel-type EAS consisting of two overlapping current-carrying coils. Two different relative positions between the EAS and the body (frontal and lateral exposures), which imply the exposure of different parts of the body at different distances, have been considered. In all cases, induced current densities in tissues of the central nervous system and specific absorption rates (SARs) are calculated to be compared with the limits from the guidelines. Results show that induced current densities are lower in the case of adult models as compared with those of children in both lateral and frontal exposures. Maximum SAR values calculated in lateral exposure are significantly lower than those calculated in frontal exposure, where the EAS-body distance is shorter. Nevertheless, in all studied cases, with an EAS driving current of 4 A rms, maximum induced current and SAR values are below basic restrictions.

How we can measure the non-driving-task engagement in automated driving: Comparing flow experience and workload.

PubMed

Ko, Sang Min; Ji, Yong Gu

2018-02-01

In automated driving, a driver can completely concentrate on non-driving-related tasks (NDRTs). This study investigated the flow experience of a driver who concentrated on NDRTs and tasks that induce mental workload under conditional automation. Participants performed NDRTs under different demand levels: a balanced demand-skill level (fit condition) to induce flow, low-demand level to induce boredom, and high-demand level to induce anxiety. In addition, they performed the additional N-Back task, which artificially induces mental workload. The results showed participants had the longest reaction time when they indicated the highest flow score, and had the longest gaze-on time, road-fixation time, hands-on time, and take-over time under the fit condition. Significant differences were not observed in the driver reaction times in the fit condition and the additional N-Back task, indicating that performing NDRTs that induce a high flow experience could influence driver reaction time similar to performing tasks with a high mental workload. Copyright © 2017. Published by Elsevier Ltd.

Automated Bone Screw Tightening to Adaptive Levels of Stripping Torque.

PubMed

Reynolds, Karen J; Mohtar, Aaron A; Cleek, Tammy M; Ryan, Melissa K; Hearn, Trevor C

2017-06-01

To use relationships between tightening parameters, related to bone quality, to develop an automated system that determines and controls the level of screw tightening. An algorithm relating current at head contact (IHC) to current at construct failure (Imax) was developed. The algorithm was used to trigger cessation of screw insertion at a predefined tightening level, in real time, between head contact and maximum current. The ability of the device to stop at the predefined level was assessed. The mean (±SD) current at which screw insertion ceased was calculated to be [51.47 ± 9.75% × (Imax - IHC)] + IHC, with no premature bone failures. A smart screwdriver was developed that uses the current from the motor driving the screw to predict the current at which the screw will strip the bone threads. The device was implemented and was able to achieve motor shut-off and cease tightening at a predefined threshold, with no premature bone failures.

Trajectory generation for an on-road autonomous vehicle

NASA Astrophysics Data System (ADS)

Horst, John; Barbera, Anthony

2006-05-01

We describe an algorithm that generates a smooth trajectory (position, velocity, and acceleration at uniformly sampled instants of time) for a car-like vehicle autonomously navigating within the constraints of lanes in a road. The technique models both vehicle paths and lane segments as straight line segments and circular arcs for mathematical simplicity and elegance, which we contrast with cubic spline approaches. We develop the path in an idealized space, warp the path into real space and compute path length, generate a one-dimensional trajectory along the path length that achieves target speeds and positions, and finally, warp, translate, and rotate the one-dimensional trajectory points onto the path in real space. The algorithm moves a vehicle in lane safely and efficiently within speed and acceleration maximums. The algorithm functions in the context of other autonomous driving functions within a carefully designed vehicle control hierarchy.

Locomotive forces produced by single leukocytes in vivo and in vitro.

PubMed

Guilford, W H; Lantz, R C; Gore, R W

1995-05-01

We report here the first time-resolved measurements of the forces produced during the migration of single leukocytes in vivo and in vitro. Pulmonary macrophages from hamsters and mice, in vitro, and Nembutal (pentobarbital sodium)-anesthetized hamster neutrophils, in vivo, generated maximum locomotive forces ranging from 1.9 to 10.7 nN or tenths of microdynes. Force production was periodic and correlated with the length of the leading lamellipod but not with generalized cell ruffling. Although the extension of the leading lamella is critical to locomotive force generation, these direct measurements suggest that lamellar extension may not arise from the same contractile processes driving forward motion of the cell mass. Indeed, cell ruffling, lamellar extension, and locomotive force generation may be differentially controlled and have different origins. This technique may be extended to test numerous hypotheses of how these and other nonmuscle cells crawl.

Short-Term Dynamic and Local Epidemiological Trends in the South American HIV-1B Epidemic.

PubMed

Junqueira, Dennis Maletich; de Medeiros, Rubia Marília; Gräf, Tiago; Almeida, Sabrina Esteves de Matos

2016-01-01

The human displacement and sexual behavior are the main factors driving the HIV-1 pandemic to the current profile. The intrinsic structure of the HIV transmission among different individuals has valuable importance for the understanding of the epidemic and for the public health response. The aim of this study was to characterize the HIV-1 subtype B (HIV-1B) epidemic in South America through the identification of transmission links and infer trends about geographical patterns and median time of transmission between individuals. Sequences of the protease and reverse transcriptase coding regions from 4,810 individuals were selected from GenBank. Maximum likelihood phylogenies were inferred and submitted to ClusterPicker to identify transmission links. Bayesian analyses were applied only for clusters including ≥5 dated samples in order to estimate the median maximum inter-transmission interval. This study analyzed sequences sampled from 12 South American countries, from individuals of different exposure categories, under different antiretroviral profiles, and from a wide period of time (1989-2013). Continentally, Brazil, Argentina and Venezuela were revealed important sites for the spread of HIV-1B among countries inside South America. Of note, from all the clusters identified about 70% of the HIV-1B infections are primarily occurring among individuals living in the same geographic region. In addition, these transmissions seem to occur early after the infection of an individual, taking in average 2.39 years (95% CI 1.48-3.30) to succeed. Homosexual/Bisexual individuals transmit the virus as quickly as almost half time of that estimated for the general population sampled here. Public health services can be broadly benefitted from this kind of information whether to focus on specific programs of response to the epidemic whether as guiding of prevention campaigns to specific risk groups.

Digital Timing Recovery for High Speed Optical Drives

NASA Astrophysics Data System (ADS)

Ko, Seok Jun; Kim, Pan Soo; Choi, Hyung Jin; Lee, Jae-Wook

2002-03-01

A new digital timing recovery scheme for the optical drive system is presented. By comparative simulations using digital versatile disc (DVD) patterns with marginal input conditions, the proposed algorithm shows enhanced performances in jitter variance and signal-to-noise ratio (SNR) margin by four times and 3 [dB], respectively.

A parametric duration model of the reaction times of drivers distracted by mobile phone conversations.

PubMed

Haque, Md Mazharul; Washington, Simon

2014-01-01

The use of mobile phones while driving is more prevalent among young drivers-a less experienced cohort with elevated crash risk. The objective of this study was to examine and better understand the reaction times of young drivers to a traffic event originating in their peripheral vision whilst engaged in a mobile phone conversation. The CARRS-Q advanced driving simulator was used to test a sample of young drivers on various simulated driving tasks, including an event that originated within the driver's peripheral vision, whereby a pedestrian enters a zebra crossing from a sidewalk. Thirty-two licensed drivers drove the simulator in three phone conditions: baseline (no phone conversation), hands-free and handheld. In addition to driving the simulator each participant completed questionnaires related to driver demographics, driving history, usage of mobile phones while driving, and general mobile phone usage history. The participants were 21-26 years old and split evenly by gender. Drivers' reaction times to a pedestrian in the zebra crossing were modelled using a parametric accelerated failure time (AFT) duration model with a Weibull distribution. Also tested where two different model specifications to account for the structured heterogeneity arising from the repeated measures experimental design. The Weibull AFT model with gamma heterogeneity was found to be the best fitting model and identified four significant variables influencing the reaction times, including phone condition, driver's age, license type (provisional license holder or not), and self-reported frequency of usage of handheld phones while driving. The reaction times of drivers were more than 40% longer in the distracted condition compared to baseline (not distracted). Moreover, the impairment of reaction times due to mobile phone conversations was almost double for provisional compared to open license holders. A reduction in the ability to detect traffic events in the periphery whilst distracted presents a significant and measurable safety concern that will undoubtedly persist unless mitigated. Copyright © 2013 Elsevier Ltd. All rights reserved.

Asleep at the automated wheel-Sleepiness and fatigue during highly automated driving.

PubMed

Vogelpohl, Tobias; Kühn, Matthias; Hummel, Thomas; Vollrath, Mark

2018-03-20

Due to the lack of active involvement in the driving situation and due to monotonous driving environments drivers with automation may be prone to become fatigued faster than manual drivers (e.g. Schömig et al., 2015). However, little is known about the progression of fatigue during automated driving and its effects on the ability to take back manual control after a take-over request. In this driving simulator study with Nö=ö60 drivers we used a three factorial 2ö×ö2ö×ö12 mixed design to analyze the progression (12ö×ö5ömin; within subjects) of driver fatigue in drivers with automation compared to manual drivers (between subjects). Driver fatigue was induced as either mainly sleep related or mainly task related fatigue (between subjects). Additionally, we investigated the drivers' reactions to a take-over request in a critical driving scenario to gain insights into the ability of fatigued drivers to regain manual control and situation awareness after automated driving. Drivers in the automated driving condition exhibited facial indicators of fatigue after 15 to 35ömin of driving. Manual drivers only showed similar indicators of fatigue if they suffered from a lack of sleep and then only after a longer period of driving (approx. 40ömin). Several drivers in the automated condition closed their eyes for extended periods of time. In the driving with automation condition mean automation deactivation times after a take-over request were slower for a certain percentage (about 30%) of the drivers with a lack of sleep (Mö=ö3.2; SDö=ö2.1ös) compared to the reaction times after a long drive (Mö=ö2.4; SDö=ö0.9ös). Drivers with automation also took longer than manual drivers to first glance at the speed display after a take-over request and were more likely to stay behind a braking lead vehicle instead of overtaking it. Drivers are unable to stay alert during extended periods of automated driving without non-driving related tasks. Fatigued drivers could pose a serious hazard in complex take-over situations where situation awareness is required to prepare for threats. Driver fatigue monitoring or controllable distraction through non-driving tasks could be necessary to ensure alertness and availability during highly automated driving. Copyright © 2018 Elsevier Ltd. All rights reserved.

Perceived driving safety and estimated blood alcohol concentration (BAC) the morning after drinking amongst young Australians attending a music festival: a cross-sectional survey.

PubMed

Fernando, Mario; Buckland, Johanna; Melwani, Prashina; Tent, Vanessa; Preston, Philip; Pit, Sabrina Winona

2018-06-20

Alcohol-related motor vehicle crashes remain a significant and costly public health issue globally. Particularly young people are over-represented in these incidents. This study set out to explore the factors that influence individuals' perceptions of their safety to drive, and the factors related to a change in intention to drive. Four hundred nine young people aged 18-40 attending an Australian multi-day music festival completed a survey measuring demographics, alcohol use, amount of sleep obtained the previous night, intention to drive, number of passengers, perceived safety to drive, estimated BAC (measured in g/210 L) and change in intention to drive following a BAC measurement via breathalysers. Statistical analyses involved univariate tests of association and multivariate logistic regression. Only one in five participants felt they were completely safe to drive. Males self-rated as less safe to drive than females. Multivariate analyses showed that licence class, sleep hours, units of alcohol consumed in the past 24 h and estimated BAC had statistically significant associations with driving safety perception. Participants who slept for greater than seven hours the previous night were three times more likely to feel safe to drive than those who had less than five hours of sleep (OR 3.05 (95% CI 1.25, 7.45)). Forty-one percent of participants changed their intended time of driving after having their BAC measured with a breathalyser. There was a statistically significant association between changing the intention to drive to a later time with an increase in each extra passenger in a participant's vehicle (OR 1.53 (95% CI 1.02, 2.30)). Whilst concerning behaviours relating to high-risk alcohol consumption were found, the study uncovered promising findings about young peoples' perceptions of their safety to drive, and their propensity to change their driving intention. The strong correlation between hours of sleep, estimated BAC, units of alcohol consumed and license class with perception of driving safety suggests an increased awareness among young people and promotion of these factors may potentially improve actual driver safety. The influence of number of passengers on intention to drive later is another important consideration for future road safety research or promotion.

Effects of fexofenadine and hydroxyzine on brake reaction time during car-driving with cellular phone use.

PubMed

Tashiro, Manabu; Horikawa, Etsuo; Mochizuki, Hideki; Sakurada, Yumiko; Kato, Motohisa; Inokuchi, Takatoshi; Ridout, Fran; Hindmarch, Ian; Yanai, Kazuhiko

2005-10-01

Antihistamines are a mainstay treatment for allergic rhinitis; however, many older agents cause adverse events, including sedation and central nervous system (CNS) impairment. Research has shown sedating effects of antihistamines on driving; currently, no known study has examined whether cellular phone usage while driving further compounds impairment in individuals administered antihistamines. The aim of this study was to examine this endpoint. In a randomized, double-blind, placebo-controlled, three-way crossover study, healthy volunteers received fexofenadine HCl 120 mg, hydroxyzine HCl 30 mg and placebo. Brake reaction time (BRT) was used to examine driving performance across four conditions: driving only; driving while completing simple calculations; complex calculations; and conversing on a cellular phone. Subjective sedation assessments were also conducted. Brake reaction time with and without cellular phone usage in fexofenadine-treated subjects did not differ significantly from placebo in any condition. In contrast, hydroxyzine-treated subjects were significantly more sedated and had slower BRTs, suggesting slower hazard recognition and brake application, compared with the fexofenadine and placebo groups in all conditions. Importantly, cellular phone operation was an additive factor, increasing BRTs in hydroxyzine-treated volunteers. Fexofenadine did not impair CNS function in subjects involved in a divided attention task of driving and cellular phone operation. Copyright (c) 2005 John Wiley & Sons, Ltd.

Reading Text While Driving

PubMed Central

Horrey, William J.; Hoffman, Joshua D.

2015-01-01

Objective In this study, we investigated how drivers adapt secondary-task initiation and time-sharing behavior when faced with fluctuating driving demands. Background Reading text while driving is particularly detrimental; however, in real-world driving, drivers actively decide when to perform the task. Method In a test track experiment, participants were free to decide when to read messages while driving along a straight road consisting of an area with increased driving demands (demand zone) followed by an area with low demands. A message was made available shortly before the vehicle entered the demand zone. We manipulated the type of driving demands (baseline, narrow lane, pace clock, combined), message format (no message, paragraph, parsed), and the distance from the demand zone when the message was available (near, far). Results In all conditions, drivers started reading messages (drivers’ first glance to the display) before entering or before leaving the demand zone but tended to wait longer when faced with increased driving demands. While reading messages, drivers looked more or less off road, depending on types of driving demands. Conclusions For task initiation, drivers avoid transitions from low to high demands; however, they are not discouraged when driving demands are already elevated. Drivers adjust time-sharing behavior according to driving demands while performing secondary tasks. Nonetheless, such adjustment may be less effective when total demands are high. Application This study helps us to understand a driver’s role as an active controller in the context of distracted driving and provides insights for developing distraction interventions. PMID:25850162

Defect-Repairable Latent Feature Extraction of Driving Behavior via a Deep Sparse Autoencoder

PubMed Central

Taniguchi, Tadahiro; Takenaka, Kazuhito; Bando, Takashi

2018-01-01

Data representing driving behavior, as measured by various sensors installed in a vehicle, are collected as multi-dimensional sensor time-series data. These data often include redundant information, e.g., both the speed of wheels and the engine speed represent the velocity of the vehicle. Redundant information can be expected to complicate the data analysis, e.g., more factors need to be analyzed; even varying the levels of redundancy can influence the results of the analysis. We assume that the measured multi-dimensional sensor time-series data of driving behavior are generated from low-dimensional data shared by the many types of one-dimensional data of which multi-dimensional time-series data are composed. Meanwhile, sensor time-series data may be defective because of sensor failure. Therefore, another important function is to reduce the negative effect of defective data when extracting low-dimensional time-series data. This study proposes a defect-repairable feature extraction method based on a deep sparse autoencoder (DSAE) to extract low-dimensional time-series data. In the experiments, we show that DSAE provides high-performance latent feature extraction for driving behavior, even for defective sensor time-series data. In addition, we show that the negative effect of defects on the driving behavior segmentation task could be reduced using the latent features extracted by DSAE. PMID:29462931

An event- and network-level analysis of college students' maximum drinking day.

PubMed

Meisel, Matthew K; DiBello, Angelo M; Balestrieri, Sara G; Ott, Miles Q; DiGuiseppi, Graham T; Clark, Melissa A; Barnett, Nancy P

2018-04-01

Heavy episodic drinking is common among college students and remains a serious public health issue. Previous event-level research among college students has examined behaviors and individual-level characteristics that drive consumption and related consequences but often ignores the social network of people with whom these heavy drinking episodes occur. The main aim of the current study was to investigate the network of social connections between drinkers on their heaviest drinking occasions. Sociocentric network methods were used to collect information from individuals in the first-year class (N=1342) at one university. Past-month drinkers (N=972) reported on the characteristics of their heaviest drinking occasion in the past month and indicated who else among their network connections was present during this occasion. Average max drinking day indegree, or the total number of times a participant was nominated as being present on another students' heaviest drinking occasion, was 2.50 (SD=2.05). Network autocorrelation models indicated that max drinking day indegree (e.g., popularity on heaviest drinking occassions) and peers' number of drinks on their own maximum drinking occasions were significantly associated with participant maximum number of drinks, after controlling for demographic variables, pregaming, and global network indegree (e.g., popularity in the entire first-year class). Being present at other peers' heaviest drinking occasions is associated with greater drinking quantities on one's own heaviest drinking occasion. These findings suggest the potential for interventions that target peer influences within close social networks of drinkers. Copyright © 2017 Elsevier Ltd. All rights reserved.

Cannabis effects on driving lateral control with and without alcohol.

PubMed

Hartman, Rebecca L; Brown, Timothy L; Milavetz, Gary; Spurgin, Andrew; Pierce, Russell S; Gorelick, David A; Gaffney, Gary; Huestis, Marilyn A

2015-09-01

Effects of cannabis, the most commonly encountered non-alcohol drug in driving under the influence cases, are heavily debated. We aim to determine how blood Δ(9)-tetrahydrocannabinol (THC) concentrations relate to driving impairment, with and without alcohol. Current occasional (≥1×/last 3 months, ≤3days/week) cannabis smokers drank placebo or low-dose alcohol, and inhaled 500mg placebo, low (2.9%)-THC, or high (6.7%)-THC vaporized cannabis over 10min ad libitum in separate sessions (within-subject design, 6 conditions). Participants drove (National Advanced Driving Simulator, University of Iowa) simulated drives (∼0.8h duration). Blood, oral fluid (OF), and breath alcohol samples were collected before (0.17h, 0.42h) and after (1.4h, 2.3h) driving that occurred 0.5-1.3h after inhalation. We evaluated standard deviations of lateral position (lane weave, SDLP) and steering angle, lane departures/min, and maximum lateral acceleration. In N=18 completers (13 men, ages 21-37years), cannabis and alcohol increased SDLP. Blood THC concentrations of 8.2 and 13.1μg/L during driving increased SDLP similar to 0.05 and 0.08g/210L breath alcohol concentrations, the most common legal alcohol limits. Cannabis-alcohol SDLP effects were additive rather than synergistic, with 5μg/L THC+0.05g/210L alcohol showing similar SDLP to 0.08g/210L alcohol alone. Only alcohol increased lateral acceleration and the less-sensitive lane departures/min parameters. OF effectively documented cannabis exposure, although with greater THC concentration variability than paired blood samples. SDLP was a sensitive cannabis-related lateral control impairment measure. During drive blood THC ≥8.2μg/L increased SDLP similar to notably-impairing alcohol concentrations. Despite OF's screening value, OF variability poses challenges in concentration-based effects interpretation. Published by Elsevier Ireland Ltd.

Surface electromyographic amplitude does not identify differences in neural drive to synergistic muscles.

PubMed

Martinez-Valdes, Eduardo; Negro, Francesco; Falla, Deborah; De Nunzio, Alessandro Marco; Farina, Dario

2018-04-01

Surface electromyographic (EMG) signal amplitude is typically used to compare the neural drive to muscles. We experimentally investigated this association by studying the motor unit (MU) behavior and action potentials in the vastus medialis (VM) and vastus lateralis (VL) muscles. Eighteen participants performed isometric knee extensions at four target torques [10, 30, 50, and 70% of the maximum torque (MVC)] while high-density EMG signals were recorded from the VM and VL. The absolute EMG amplitude was greater for VM than VL ( P < 0.001), whereas the EMG amplitude normalized with respect to MVC was greater for VL than VM ( P < 0.04). Because differences in EMG amplitude can be due to both differences in the neural drive and in the size of the MU action potentials, we indirectly inferred the neural drives received by the two muscles by estimating the synaptic inputs received by the corresponding motor neuron pools. For this purpose, we analyzed the increase in discharge rate from recruitment to target torque for motor units matched by recruitment threshold in the two muscles. This analysis indicated that the two muscles received similar levels of neural drive. Nonetheless, the size of the MU action potentials was greater for VM than VL ( P < 0.001), and this difference explained most of the differences in EMG amplitude between the two muscles (~63% of explained variance). These results indicate that EMG amplitude, even following normalization, does not reflect the neural drive to synergistic muscles. Moreover, absolute EMG amplitude is mainly explained by the size of MU action potentials. NEW & NOTEWORTHY Electromyographic (EMG) amplitude is widely used to compare indirectly the strength of neural drive received by synergistic muscles. However, there are no studies validating this approach with motor unit data. Here, we compared between-muscles differences in surface EMG amplitude and motor unit behavior. The results clarify the limitations of surface EMG to interpret differences in neural drive between muscles.

Probabilistic Reasoning for Robustness in Automated Planning

NASA Technical Reports Server (NTRS)

Schaffer, Steven; Clement, Bradley; Chien, Steve

2007-01-01

A general-purpose computer program for planning the actions of a spacecraft or other complex system has been augmented by incorporating a subprogram that reasons about uncertainties in such continuous variables as times taken to perform tasks and amounts of resources to be consumed. This subprogram computes parametric probability distributions for time and resource variables on the basis of user-supplied models of actions and resources that they consume. The current system accepts bounded Gaussian distributions over action duration and resource use. The distributions are then combined during planning to determine the net probability distribution of each resource at any time point. In addition to a full combinatoric approach, several approximations for arriving at these combined distributions are available, including maximum-likelihood and pessimistic algorithms. Each such probability distribution can then be integrated to obtain a probability that execution of the plan under consideration would violate any constraints on the resource. The key idea is to use these probabilities of conflict to score potential plans and drive a search toward planning low-risk actions. An output plan provides a balance between the user s specified averseness to risk and other measures of optimality.

Glaucomatous retinal nerve fiber layer thickness loss is associated with slower reaction times under a divided attention task.

PubMed

Tatham, Andrew J; Boer, Erwin R; Rosen, Peter N; Della Penna, Mauro; Meira-Freitas, Daniel; Weinreb, Robert N; Zangwill, Linda M; Medeiros, Felipe A

2014-11-01

To examine the relationship between glaucomatous structural damage and ability to divide attention during simulated driving. Cross-sectional observational study. Hamilton Glaucoma Center, University of California San Diego. Total of 158 subjects from the Diagnostic Innovations in Glaucoma Study, including 82 with glaucoma and 76 similarly aged controls. Ability to divide attention was investigated by measuring reaction times to peripheral stimuli (at low, medium, or high contrast) while concomitantly performing a central driving task (car following or curve negotiation). All subjects had standard automated perimetry (SAP) and optical coherence tomography was used to measure retinal nerve fiber layer (RNFL) thickness. Cognitive ability was assessed using the Montreal Cognitive Assessment and subjects completed a driving history questionnaire. Reaction times to the driving simulator divided attention task. The mean reaction times to the low-contrast stimulus were 1.05 s and 0.64 s in glaucoma and controls, respectively, during curve negotiation (P < .001), and 1.19 s and 0.77 s (P = .025), respectively, during car following. There was a nonlinear relationship between reaction times and RNFL thickness in the better eye. RNFL thickness remained significantly associated with reaction times even after adjusting for age, SAP mean deviation in the better eye, cognitive ability, and central driving task performance. Although worse SAP sensitivity was associated with worse ability to divide attention, RNFL thickness measurements provided additional information. Information from structural tests may improve our ability to determine which patients are likely to have problems performing daily activities, such as driving. Copyright © 2014 Elsevier Inc. All rights reserved.

Theory of many-body localization in periodically driven systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abanin, Dmitry A., E-mail: dabanin@gmail.com; De Roeck, Wojciech; Huveneers, François

We present a theory of periodically driven, many-body localized (MBL) systems. We argue that MBL persists under periodic driving at high enough driving frequency: The Floquet operator (evolution operator over one driving period) can be represented as an exponential of an effective time-independent Hamiltonian, which is a sum of quasi-local terms and is itself fully MBL. We derive this result by constructing a sequence of canonical transformations to remove the time-dependence from the original Hamiltonian. When the driving evolves smoothly in time, the theory can be sharpened by estimating the probability of adiabatic Landau–Zener transitions at many-body level crossings. Inmore » all cases, we argue that there is delocalization at sufficiently low frequency. We propose a phase diagram of driven MBL systems.« less