Correlation between Reynolds number and eccentricity effect in stenosed artery models.

PubMed

Javadzadegan, Ashkan; Shimizu, Yasutomo; Behnia, Masud; Ohta, Makoto

2013-01-01

Flow recirculation and shear strain are physiological processes within coronary arteries which are associated with pathogenic biological pathways. Distinct Quite apart from coronary stenosis severity, lesion eccentricity can cause flow recirculation and affect shear strain levels within human coronary arteries. The aim of this study is to analyse the effect of lesion eccentricity on the transient flow behaviour in a model of a coronary artery and also to investigate the correlation between Reynolds number (Re) and the eccentricity effect on flow behaviour. A transient particle image velocimetry (PIV) experiment was implemented in two silicone based models with 70% diameter stenosis, one with eccentric stenosis and one with concentric stenosis. At different times throughout the flow cycle, the eccentric model was always associated with a greater recirculation zone length, maximum shear strain rate and maximum axial velocity; however, the highest and lowest impacts of eccentricity were on the recirculation zone length and maximum shear strain rate, respectively. Analysis of the results revealed a negative correlation between the Reynolds number (Re) and the eccentricity effect on maximum axial velocity, maximum shear strain rate and recirculation zone length. As Re number increases the eccentricity effect on the flow behavior becomes negligible.

Ozone synthesis improves by increasing number density of plasma channels and lower voltage in a nonthermal plasma

NASA Astrophysics Data System (ADS)

Arif Malik, Muhammad; Hughes, David

2016-04-01

Improvements in ozone synthesis from air and oxygen by increasing the number density of plasma channels and lower voltage for the same specific input energy (SIE) were explored in a nonthermal plasma based on a sliding discharge. The number of plasma channels and energy per pulse increased in direct proportion to the increase in the effective length of the anode (the high voltage electrode). Decreasing the discharge gap increased the energy per pulse for the same length and allowed the installation of more electrode pairs in the same space. It allowed the increase of the number of plasma channels in the same space to achieve the same SIE at a lower peak voltage with less energy per plasma channel. The ozone concentration gradually increased to ~1500 ppmv (140 to 50 g kWh-1) from air and to ~6000 ppmv (400 to 200 g kWh-1) from oxygen with a gradual increase in the SIE to ~200 J L-1, irrespective of the variations in electrode geometry, applied voltage or flow rate of the feed gas. A gradual increase in SIE beyond 200 J L-1 gradually increased the ozone concentration to a certain maximum value followed by a decline, but the rate of increase and the maximum value was higher for the greater number of plasma channels and lower peak voltage combination. The maximum ozone concentration was ~5000 ppmv (~30 g kWh-1) from air and ~22 000 ppmv (~80 g kWh-1) from oxygen. The results are explained on the basis of characteristics of the plasma and ozone synthesis mechanism.

The effect of active recovery on power performance during the bench press exercise.

PubMed

Lopes, Felipe A S; Panissa, Valéria L G; Julio, Ursula F; Menegon, Elton M; Franchini, Emerson

2014-03-27

The objective of this study was to verify the effect of active and passive recovery on blood lactate concentration and power performance. Twelve male subjects were submitted to a maximal strength test in the the bench press, a maximal aerobic test in the bench step, and to four sets of bench press exercise performed as fast and as long as possible, using 80% of maximal strength when active or passive recovery was performed. The maximum number of repetitions, mean and peak power in eccentric and concentric phases were computed and blood lactate concentration was measured. Comparisons for the variables were made using a two-way variance analysis (recovery type and set numer) with repeated measures in the second factor. When significant differences were detected (p < 0.05), a Tukey post-hoc test was used. There was a main effect of set number on maximum number of repetitions (p < 0.05) (1 > 2, 3, and 4; 2 > 3 and 4; 3 > 4). Mean and peak power in both eccentric and concentric phases also differed across sets (1 > 2, 3, and 4; 2 > 4). There was also a main effect for the recovery type, with lower values (p < 0.05) observed for the active recovery compared to the passive one. It can be concluded that active recovery resulted in lower lactate concentration, but did not improve power performance in the bench press exercise.

The Effect of Active Recovery on Power Performance During the Bench Press Exercise

PubMed Central

Lopes, Felipe A. S.; Panissa, Valéria L. G.; Julio, Ursula F.; Menegon, Elton M.; Franchini, Emerson

2014-01-01

The objective of this study was to verify the effect of active and passive recovery on blood lactate concentration and power performance. Twelve male subjects were submitted to a maximal strength test in the the bench press, a maximal aerobic test in the bench step, and to four sets of bench press exercise performed as fast and as long as possible, using 80% of maximal strength when active or passive recovery was performed. The maximum number of repetitions, mean and peak power in eccentric and concentric phases were computed and blood lactate concentration was measured. Comparisons for the variables were made using a two-way variance analysis (recovery type and set numer) with repeated measures in the second factor. When significant differences were detected (p < 0.05), a Tukey post-hoc test was used. There was a main effect of set number on maximum number of repetitions (p < 0.05) (1 > 2, 3, and 4; 2 > 3 and 4; 3 > 4). Mean and peak power in both eccentric and concentric phases also differed across sets (1 > 2, 3, and 4; 2 > 4). There was also a main effect for the recovery type, with lower values (p < 0.05) observed for the active recovery compared to the passive one. It can be concluded that active recovery resulted in lower lactate concentration, but did not improve power performance in the bench press exercise. PMID:25031684

Concentrations of organic contaminants detected during managed flow conditions, San Joaquin River and Old River, California, 2001

USGS Publications Warehouse

Orlando, James L.; Kuivila, Kathryn

2005-01-01

Concentrations of organic contaminants were determined in water samples collected at six surface-water sites located along the San Joaquin and Old Rivers during April through June 2001. Water samples were collected, coincident with salmon smolt caging studies conducted by researchers from the Bodega Marine Laboratory at the University of California at Davis to characterize exposure of the salmon smolt to organic contaminants. Sampling occurred prior to, during, and following the implementation of managed streamflow conditions on the San Joaquin and Old Rivers as part of the Vernalis Adaptive Management Plan. Thirteen pesticides were detected in water samples collected during this study, and at least five pesticides were detected in each sample. The total number of pesticide detections varied little between river systems and between sites, but the maximum concentrations of most pesticides occurred in San Joaquin River samples. The total number of pesticides detected varied little over the three time periods. However, during the period of managed streamflow, the fewest number of pesticides were detected at their absolute maximum concentration. Nine wastewater compounds were detected during this study. Suspended-sediment concentrations were similar for the San Joaquin and Old Rivers except during the period of managed streamflow conditions, when suspended-sediment concentration was higher at sites on the San Joaquin River than at sites on the Old River. Values for water parameters (pH, specific conductance, and hardness) were lowest during the period of managed flows.

Power consumption analysis DBD plasma ozone generator

NASA Astrophysics Data System (ADS)

Nur, M.; Restiwijaya, M.; Muchlisin, Z.; Susan, I. A.; Arianto, F.; Widyanto, S. A.

2016-11-01

Studies on the consumption of energy by an ozone generator with various constructions electrodes of dielectric barrier discharge plasma (DBDP) reactor has been carried out. This research was done to get the configuration of the reactor, that is capable to produce high ozone concentrations with low energy consumption. BDBP reactors were constructed by spiral- cylindrical configuration, plasma ozone was generated by high voltage AC voltage up to 25 kV and maximum frequency of 23 kHz. The reactor consists of an active electrode in the form of a spiral-shaped with variation diameter Dc, and it was made by using copper wire with diameter Dw. In this research, we variated number of loops coil windings N as well as Dc and Dw. Ozone concentrations greater when the wire's diameter Dw and the diameter of the coil windings applied was greater. We found that impedance greater will minimize the concentration of ozone, in contrary to the greater capacitance will increase the concentration of ozone. The ozone concentrations increase with augmenting of power. Maximum power is effective at DBD reactor spiral-cylinder is on the Dc = 20 mm, Dw = 1.2 mm, and the number of coil windings N = 10 loops with the resulting concentration is greater than 20 ppm and it consumes energy of 177.60 watts

Seasonal changes in concentrations of dissolved pesticides and organic carbon in the Sacramento-San Joaquin delta, California, 1994-1996

USGS Publications Warehouse

Orlando, James L.; Kuivila, Kathryn

2006-01-01

The Sacramento-San Joaquin Delta (Delta) of California is an ecologically rich and hydrologically complex region that receives runoff from nearly one-quarter of the state. Water-quality studies of surface water in the region have found dissolved pesticides in winter storm runoff at concentrations toxic to some aquatic invertebrates. However, scientists have little information on pesticide concentrations in the Delta on a seasonal timescale or the importance of pesticide contributions from within-Delta sources. Consequently, the U.S. Geological Survey conducted a study from 1994 to 1996 during which water samples were collected seasonally from 31 sites located within the Delta and on major tributaries to the Delta. Water samples were analyzed for 20 current-use pesticides and dissolved organic carbon. During the study, 11 current-use pesticides were detected; maximum concentrations ranging from 17 ng/L (for trifluralin) to 1,160 ng/L (for metolachlor). The highest concentrations of five pesticides (carbaryl, carbofuran, metolachlor, molinate, and simazine) were greater than 900 ng/L. The greatest number of pesticides was detected in the summer of 1994, whereas the least number were detected in the winter of 1994. The herbicides metolachlor and simazine were the most frequently detected pesticides and were detected in five of the six sampling seasons. The herbicides molinate and EPTC were detected only during the three summer sampling seasons. A comparison of pesticides detected during the spring and summer of 1995 showed some seasonal variability. Comparison of the three summer seasons sampled showed that a larger number of pesticides were detected, and with generally higher maximum concentrations, in 1994 than in 1995 or 1996. Dissolved organic carbon (DOC) concentrations ranged, over the course of the study, from 1.4 mg/L to 10.4 mg/L, and had a median concentration of 3.8 mg/L. On a seasonal basis, the lowest maximum DOC concentrations occurred during the summer and winter of 1994. The highest median DOC concentration on a seasonal basis occurred in the spring of 1995. This previously unreported data is being published now to provide historical information on pesticide concentrations in the Delta to water managers and the scientific community.

Impacts of Future European Emission Reductions on Aerosol Particle Number Concentrations Accounting for Effects of Ammonia, Amines, and Organic Species.

PubMed

Julin, Jan; Murphy, Benjamin N; Patoulias, David; Fountoukis, Christos; Olenius, Tinja; Pandis, Spyros N; Riipinen, Ilona

2018-01-16

Although they are currently unregulated, atmospheric ultrafine particles (<100 nm) pose health risks because of, e.g., their capability to penetrate deep into the respiratory system. Ultrafine particles, often minor contributors to atmospheric particulate mass, typically dominate aerosol particle number concentrations. We simulated the response of particle number concentrations over Europe to recent estimates of future emission reductions of aerosol particles and their precursors. We used the chemical transport model PMCAMx-UF, with novel updates including state-of-the-art descriptions of ammonia and dimethylamine new particle formation (NPF) pathways and the condensation of organic compounds onto particles. These processes had notable impacts on atmospheric particle number concentrations. All three emission scenarios (current legislation, optimized emissions, and maximum technically feasible reductions) resulted in substantial (10-50%) decreases in median particle number concentrations over Europe. Consistent reductions were predicted in Central Europe, while Northern Europe exhibited smaller reductions or even increased concentrations. Motivated by the improved NPF descriptions for ammonia and methylamines, we placed special focus on the potential to improve air quality by reducing agricultural emissions, which are a major source of these species. Agricultural emission controls showed promise in reducing ultrafine particle number concentrations, although the change is nonlinear with particle size.

Methods for fitting a parametric probability distribution to most probable number data.

PubMed

Williams, Michael S; Ebel, Eric D

2012-07-02

Every year hundreds of thousands, if not millions, of samples are collected and analyzed to assess microbial contamination in food and water. The concentration of pathogenic organisms at the end of the production process is low for most commodities, so a highly sensitive screening test is used to determine whether the organism of interest is present in a sample. In some applications, samples that test positive are subjected to quantitation. The most probable number (MPN) technique is a common method to quantify the level of contamination in a sample because it is able to provide estimates at low concentrations. This technique uses a series of dilution count experiments to derive estimates of the concentration of the microorganism of interest. An application for these data is food-safety risk assessment, where the MPN concentration estimates can be fitted to a parametric distribution to summarize the range of potential exposures to the contaminant. Many different methods (e.g., substitution methods, maximum likelihood and regression on order statistics) have been proposed to fit microbial contamination data to a distribution, but the development of these methods rarely considers how the MPN technique influences the choice of distribution function and fitting method. An often overlooked aspect when applying these methods is whether the data represent actual measurements of the average concentration of microorganism per milliliter or the data are real-valued estimates of the average concentration, as is the case with MPN data. In this study, we propose two methods for fitting MPN data to a probability distribution. The first method uses a maximum likelihood estimator that takes average concentration values as the data inputs. The second is a Bayesian latent variable method that uses the counts of the number of positive tubes at each dilution to estimate the parameters of the contamination distribution. The performance of the two fitting methods is compared for two data sets that represent Salmonella and Campylobacter concentrations on chicken carcasses. The results demonstrate a bias in the maximum likelihood estimator that increases with reductions in average concentration. The Bayesian method provided unbiased estimates of the concentration distribution parameters for all data sets. We provide computer code for the Bayesian fitting method. Published by Elsevier B.V.

Experimental and numerical study on heat transfer enhancement of flat tube radiator using Al2O3 and CuO nanofluids

NASA Astrophysics Data System (ADS)

Alosious, Sobin; R, Sarath S.; Nair, Anjan R.; Krishnakumar, K.

2017-12-01

Forced convective heat transfer of Al2O3 and CuO nanofluids through flat tube automobile radiator were studied experimentally and numerically. Nanofluids of 0.05% volume concentrations were prepared with Al2O3 and CuO nanoparticles having diameter below 50 nm. The working fluid recirculates through an automobile flat tube radiator with constant inlet temperature of 90 °C. Experiments were conducted by using water and nanofluids by varying the Reynolds numbers from 136 to 816. The flat tube of the radiator with same dimensions were modeled and numerically studied the heat transfer. The model includes the thickness of tube wall and also considers the effect of fins in the radiator. Numerical studies were carried out for six different volume concentrations from 0.05% to 1% and Reynolds number varied between 136 and 816 for both nanofluids. The results show an enhancement in heat transfer coefficient and effectiveness of radiator with increase in Reynolds number and volume concentration. A maximum enhancement of 13.2% and 16.4% in inside heat transfer coefficient were obtained for 1% concentration of CuO and Al2O3 nanofluids respectively. However increasing the volume concentration causes an increase in viscosity and density, which leads to an increase in pumping power. For same heat rejection of water, the area of the radiator can be reduced by 2.1% and 2.9% by using 1% concentration of CuO and Al2O3 nanofluids respectively. The optimum values of volume concentration were found to be 0.4% to 0.8% in which heat transfer enhancement dominates pumping power increase. Al2O3 nanofluids gives the maximum heat transfer enhancement and stability compared to CuO nanofluids.

Adenylate Energy Pool and Energy Charge in Maturing Rape Seeds 1

PubMed Central

Ching, Te May; Crane, Jim M.; Stamp, David L.

1974-01-01

A study of energy state and chemical composition of pod walls and seeds of maturing rape (Brassica napus L.) was conducted on two varieties, Victor and Gorczanski. Total adenosine phosphates, ATP, and adenylate energy charge increased with increasing cell number and cellular synthesis during the early stages, remained high at maximum dry weight accumulation and maximum substrate influx time, and decreased with ripening. A temporal control of energy supply and ATP concentration is evident in developing tissues with determined functions; whereas the association of a high energy charge and active cellular biosynthesis occurs only in tissues with a stabilized cell number. PMID:16658964

Control of Growth Rate by Initial Substrate Concentration at Values Below Maximum Rate

PubMed Central

Gaudy, Anthony F.; Obayashi, Alan; Gaudy, Elizabeth T.

1971-01-01

The hyperbolic relationship between specific growth rate, μ, and substrate concentration, proposed by Monod and used since as the basis for the theory of steady-state growth in continuous-flow systems, was tested experimentally in batch cultures. Use of a Flavobacterium sp. exhibiting a high saturation constant for growth in glucose minimal medium allowed direct measurement of growth rate and substrate concentration throughout the growth cycle in medium containing a rate-limiting initial concentration of glucose. Specific growth rates were also measured for a wide range of initial glucose concentrations. A plot of specific growth rate versus initial substrate concentration was found to fit the hyperbolic equation. However, the instantaneous relationship between specific growth rate and substrate concentration during growth, which is stated by the equation, was not observed. Well defined exponential growth phases were developed at initial substrate concentrations below that required for support of the maximum exponential growth rate and a constant doubling time was maintained until 50% of the substrate had been used. It is suggested that the external substrate concentration initially present “sets” the specific growth rate by establishing a steady-state internal concentration of substrate, possibly through control of the number of permeation sites. PMID:5137579

Concentration of Naegleria fowleri in natural waters used for recreational purposes in Sonora, Mexico (November 2007-October 2008).

PubMed

Lares-Villa, Fernando; Hernández-Peña, Claudia

2010-09-01

A survey was designed to know the concentration of Naegleria fowleri in recreational areas in Hornos, Sonora, during a year. Samples were taken monthly at La Isleta and Las Palmas and the total amoeba counts were obtained by the most probable number method (MPN). The identification of N. fowleri was made by PCR. The maximum concentration of total thermophilic amoebae was 9175 MPN/L for La Isleta and 3477 MPN/L for Las Palmas. Thermophilic Naegleria were present mainly during summer and fall. October's concentrations were up to 201 MPN/L, at both places. The maximum concentrations of N. fowleri were 201 MPN/L and 18 MPN/L for La Isleta and Las Palmas respectively, and were isolated from August to October. The presence of N. fowleri in these particular natural bodies of water reinforces the need for adaptation of preventive measures to avoid cases of primary amoebic meningoencephalitis. Copyright 2010 Elsevier Inc. All rights reserved.

Multivariate Regression Analysis of Winter Ozone Events in the Uinta Basin of Eastern Utah, USA

NASA Astrophysics Data System (ADS)

Mansfield, M. L.

2012-12-01

I report on a regression analysis of a number of variables that are involved in the formation of winter ozone in the Uinta Basin of Eastern Utah. One goal of the analysis is to develop a mathematical model capable of predicting the daily maximum ozone concentration from values of a number of independent variables. The dependent variable is the daily maximum ozone concentration at a particular site in the basin. Independent variables are (1) daily lapse rate, (2) daily "basin temperature" (defined below), (3) snow cover, (4) midday solar zenith angle, (5) monthly oil production, (6) monthly gas production, and (7) the number of days since the beginning of a multi-day inversion event. Daily maximum temperature and daily snow cover data are available at ten or fifteen different sites throughout the basin. The daily lapse rate is defined operationally as the slope of the linear least-squares fit to the temperature-altitude plot, and the "basin temperature" is defined as the value assumed by the same least-squares line at an altitude of 1400 m. A multi-day inversion event is defined as a set of consecutive days for which the lapse rate remains positive. The standard deviation in the accuracy of the model is about 10 ppb. The model has been combined with historical climate and oil & gas production data to estimate historical ozone levels.

Exposure to particulate matter in a mosque

NASA Astrophysics Data System (ADS)

Ocak, Yılmaz; Kılıçvuran, Akın; Eren, Aykut Balkan; Sofuoglu, Aysun; Sofuoglu, Sait C.

2012-09-01

Indoor air quality in mosques during prayers may be of concern for sensitive/susceptible sub-groups of the population. However, no indoor air pollutant levels of potentially toxic agents in mosques have been reported in the literature. This study measured PM concentrations in a mosque on Friday when the mid-day prayer always receives high attendance. Particle number and CO2 concentrations were measured on nine sampling days in three different campaigns before, during, and after prayer under three different cleaning schedules: vacuuming a week before, a day before, and on the morning of the prayer. In addition, daily PM2.5 concentrations were measured. Number concentrations in 0.5-1.0, 1.0-5.0, and > 5.0 μm diameter size ranges were monitored. In all campaigns the maximum number concentrations were observed on the most crowded days. The lowest number concentrations occurred when vacuuming was performed a day before the prayer day in two of the three size ranges considered. PM2.5 concentrations (four-hour samples that integrated before, during, and after the prayer) were comparable to the other indoor environments reported in the literature. CO2 concentrations suggested that ventilation was not sufficient in the mosque during the prayers. The results showed that better ventilation, a preventive cleaning strategy, and a more detailed study are needed.

Polychlorinated biphenyls and organochlorine pesticides in plasma and the embryonic development in Lake Erie water snakes (Nerodia sipedon insularum) from Pelee Island, Ontario, Canada (1999).

PubMed

Bishop, C A; Rouse, J D

2006-10-01

From three locations along a 34-km shoreline of Pelee Island, Ontario, 30 gravid female Lake Erie water snakes (Nerodia sipedon insularum) were sampled to determine the organochlorine (OC) contaminant levels in plasma and the number of live and dead embryos present in the body cavity. Plasma was analyzed for 59 polychlorinated biphenyl (PCB) congeners and 14 organochlorine pesticides. Concentrations of pesticides were low (< or =0.1 ng/g wet wt) in all snakes, but there was significant variation in mean PCB concentrations in plasma from among the sampling locations on Pelee Island. Snakes (n = 5) from the West shore and dock area of the island had significantly higher PCB concentrations (90.4 +/- 15.0 ng/g wet wt) in plasma than those from Lighthouse Point (n = 5; 34.4 +/- 13 ng/g wet wt) and the south shore of the island (n = 5; 29.4 +/- 16.3 ng/g wet wt). Body mass of the female snakes ranged from 252 to 880 g, and mean masses were not significantly different among sample sites. The number of live embryos found ranged from 13 to 46 female snakes and no dead embryos were detected. There were significant positive correlations among body mass, snout-vent length, and number of young per female. There were no significant correlations among body mass, snout-vent length, number of young per female, or per-gram body mass of female snakes and contaminant concentrations in plasma. It was concluded that an interim estimate of a no-effect level on embryonic survival in N. sipedon insularum may be a maximum average concentration of 90.4 ng/g wet wt PCBs and a maximum average concentration of 3.6 ng/g wet wt p,p'-dichloro-diphenyl-dichloroethylene in plasma.

Assessment of natural sepiolite on cadmium stabilization, microbial communities, and enzyme activities in acidic soil.

PubMed

Sun, Yuebing; Sun, Guohong; Xu, Yingming; Wang, Lin; Liang, Xuefeng; Lin, Dasong; Hu, Fazhi

2013-05-01

A pot trial was conducted to assess the efficiency of sepiolite-induced cadmium (Cd) immobilization in ultisoils. Under Cd concentrations of 1.25, 2.5, and 5 mg kg(-1), the available Cd in the soil after the application of 1-10 % sepiolite decreased by a maximum of 44.4, 23.0, and 17.0 %, respectively, compared with no sepiolite treatments. The increase in the values of soil enzyme activities and microbial number proved that a certain metabolic recovery occurred after sepiolite treatment. The dry biomass of spinach (Spinacia oleracea) increased with increasing sepiolite concentration in the soil. However, the concentration (dry weight) of Cd in the spinach shoots decreased with the increase in sepiolite dose, with maximum reduction of 92.2, 90.0, and 84.9 %, respectively, compared with that of unamended soils. Under a Cd level of 1.25 mg kg(-1), the Cd concentration in the edible parts of spinach at 1 % sepiolite amendment was lower than 0.2 mg kg(-1) fresh weight, the maximum permissible concentration (MPC) of Cd in vegetable. Even at higher Cd concentrations (2.5 and 5 mg kg(-1)), safe spinach was produced when the sepiolite treatment was up to 5 %. The results showed that sepiolite-assisted remediation could potentially succeed on a field scale by decreasing Cd entry into the food chain.

Properties of Arctic Aerosol Particles and Residuals of Warm Clouds: Cloud Activation Efficiency and the Aerosol Indirect Effect

NASA Astrophysics Data System (ADS)

Zelenyuk, A.; Imre, D. G.; Leaitch, R.; Ovchinnikov, M.; Liu, P.; Macdonald, A.; Strapp, W.; Ghan, S. J.; Earle, M. E.

2012-12-01

Single particle mass spectrometer, SPLAT II, was used to characterize the size, composition, number concentration, density, and shape of individual Arctic spring aerosol. Background particles, particles above and below the cloud, cloud droplet residuals, and interstitial particles were characterized with goal to identify the properties that separate cloud condensation nuclei (CCN) from background aerosol particles. The analysis offers a comparison between warm clouds formed on clean and polluted days, with clean days having maximum particle concentrations (Na) lower than ~250 cm-3, as compared with polluted days, in which maximum concentration was tenfold higher. On clean days, particles were composed of organics, organics mixed with sulfates, biomass burning (BB), sea salt (SS), and few soot and dust particles. On polluted days, BB, organics associated with BB, and their mixtures with sulfate dominated particle compositions. Based on the measured compositions and size distributions of cloud droplet residuals, background aerosols, and interstitial particles, we conclude that these three particle types had virtually the same compositions, which means that cloud activation probabilities were surprisingly nearly composition independent. Moreover, these conclusions hold in cases in which less than 20% or more than 90% of background particles got activated. We concluded that for the warm clouds interrogated in this study particle size played a more important factor on aerosol CCN activity. Comparative analysis of all studied clouds reveals that aerosol activation efficiency strongly depends on the aerosol concentrations, such that at Na <200 cm-3, nearly all particles activate, and at higher concentrations the activation efficiency is lower. For example, when Na was greater than 1500 cm-3, less than ~30% of particles activated. The data suggest that as the number of nucleated droplets increases, condensation on existing droplets effectively competes with particle activation, limiting maximum droplet concentrations Nd = 525 ± 50 cm-3, which is lower than the 750 cm-3 limit found by Leaitch et al. (1986) for mid-latitude continental cloud that had generally larger updraft speeds than the clouds interrogated in Arctic. These findings are important for the aerosol indirect effect, in which increase in aerosol particle number concentrations is expected to result in increase in Nd and decrease in droplet size, leading to increased cloud albedo and potentially lifetimes. Our conclusions point to limited susceptibility to changes in ambient aerosol concentrations, providing simple explanation for the finding of weaker than expected indirect effect. In summary, the data presented here show that Nd increases as the cloud base particle number concentration increases; however, they also show a limit on Nd that is in the range of 500-600 cm-3.

Quantitative regulation of B cell division destiny by signal strength.

PubMed

Turner, Marian L; Hawkins, Edwin D; Hodgkin, Philip D

2008-07-01

Differentiation to Ab secreting and isotype-switched effector cells is tightly linked to cell division and therefore the degree of proliferation strongly influences the nature of the immune response. The maximum number of divisions reached, termed the population division destiny, is stochastically distributed in the population and is an important parameter in the quantitative outcome of lymphocyte responses. In this study, we further assessed the variables that regulate B cell division destiny in vitro in response to T cell- and TLR-dependent stimuli. Both the concentration and duration of stimulation were able to regulate the average maximum number of divisions undergone for each stimulus. Notably, a maximum division destiny was reached during provision of repeated saturating stimulation, revealing that an intrinsic limit to proliferation exists even under these conditions. This limit was linked directly to division number rather than time of exposure to stimulation and operated independently of the survival regulation of the cells. These results demonstrate that a B cell population's division destiny is regulable by the stimulatory conditions up to an inherent maximum value. Division destiny is a crucial parameter in regulating the extent of B cell responses and thereby also the nature of the immune response mounted.

A study on the imaging characteristics of Gold nanoparticles as a contrast agent in X-ray computed tomography

NASA Astrophysics Data System (ADS)

Mesbahi, Asghar; Famouri, Fatemeh; Ahar, Mohammad Johari; Ghaffari, Maryam Olade; Ghavami, Seyed Mostafa

2017-03-01

Aim: In the current study, some imaging characteristics of AuNPs were quantitatively analyzed and compared with two conventional contrast media (CM) including Iodine and Gadolinium by using of a cylindrical phantom. Methods: AuNPs were synthesized with the mean diameter of 16 nm and were equalized to the concentration of 0.5, 1, 2 and 4 mg/mL in the same volumes. A cylindrical phantom resembling the head and neck was fabricated and drilled to contain small tubes filled with Iodine, Gadolinium, and AuNPs as contrast media. The phantom was scanned in different exposure techniques and CT numbers of three studied contrast media inside test tubes were measured in terms of Hounsfield Unit (HU). The imaging parameters of the noise and contrast to noise ratios (CNR) were calculated for all studied CMs. Results: AuNPs showed 128% and 166% higher CT number in comparison with Iodine and Gadolinium respectively. Also, Iodine had a greater CT number than Gadolinium for the same exposure techniques and concentration. The maximum CT number for AuNPs and studied contrast materials was obtained at the highest mAs and the lowest tube potential. The maximum CT number were 1033±11 (HU) for AuNP, 565±10 (HU) for Iodine, 458±11 for Gadolinium. Moreover, the maximum CNRs of 433±117, 203±53, 145±37 were found for AuNPs, Iodine and Gadolinium respectively. Conclusion: The contrast agent based on AuNPs showed higher imaging quality in terms of contrast and noise relative to other iodine and gadolinium based contrast media in X-ray computed tomography. Application of the AuNPs as a contrast medium in x-ray CT is recommended.

Chlordane, DDT, PCB's, and other selected organic compounds in Asiatic clams and yellow bullhead in the Potomac River Basin, 1992

USGS Publications Warehouse

Zappia, Humbert

1996-01-01

Chlordane, DDT (dichlor-diphenyl-trichloroethane), and PCB's (polychlorinated biphenyls) were the most widespread organic contaminants detected during a 1992 survey of aquatic biological tissues in the Potomac River Basin. On the basis of existing U.S. Food and Drug Administration criteria, no new threats to human health were discovered, although chlordane concentrations may pose a threat to fish-eating wildlife. Chlordane exceeded the National Academy of Science and National Academy of Engineering recommended maximum concentration for the protection of fish-eating wildlife at two sites. The survey, conducted by the U.S. Geological Survey's National Water-Quality Assessment Program, sampled Asiatic clams (Corbicula fluminea) and yellow bullhead (Ameiurus natalis) at 16 sites to determine the occurrence and distribution of 29 hydrophobic organic compounds. Thirteen of these organic compounds were detected in the survey. Sites with the greatest number of compounds detected include the Potomac River near Alexandria, Va., with 6 compounds detected in Asiatic clam tissue, and Accotink Creek near Annandale, Va., with 11 compounds in yellow bullhead tissue. Chlordane was detected at six sites, with maximum concentrations of 31.1 ?g/kg (micrograms per kilograms) in Asiatic clam tissue and 127 ?g/kg in yellow bullhead whole-fish tissue. DDT was detected at five sites, with maximum concentrations of 12.9 ?g/kg in Asiatic clam tissue and 7.6 ?g/kg in yellow bullhead whole-fish tissue. PCB's were detected at nine sites, with maximum concentrations of 162 ?g/kg in Asiatic clam tissue and 146 mg/ kg in yellow bullhead whole-fish tissue.

The effectiveness of radon preventive and remedial measures in Irish homes.

PubMed

Long, S; Fenton, D; Cremin, M; Morgan, A

2013-03-01

It is estimated that approximately 100 000 Irish homes have radon concentrations above the reference level of 200 Bq m(-3). To minimise the number of new homes with this problem, building regulations require that all new homes built since July 1998 in high radon areas are installed with radon barriers during construction. Measurements on local authority homes in a number of high radon areas have allowed the impact of these new regulations to be assessed. In County Cork a reduction of up to 70% in the mean radon concentration was observed in homes built since 1998 relative to those built before this date. A reduction in both the number of homes exceeding the reference level and the maximum concentration measured in homes was also measured. Homes exceeding the reference level were remediated with the use of an active sump. The results of this remedial work are also presented and show that the mean reduction in radon concentration achieved was 92%.

Effects of experimental design on calibration curve precision in routine analysis

PubMed Central

Pimentel, Maria Fernanda; Neto, Benício de Barros; Saldanha, Teresa Cristina B.

1998-01-01

A computational program which compares the effciencies of different experimental designs with those of maximum precision (D-optimized designs) is described. The program produces confidence interval plots for a calibration curve and provides information about the number of standard solutions, concentration levels and suitable concentration ranges to achieve an optimum calibration. Some examples of the application of this novel computational program are given, using both simulated and real data. PMID:18924816

The efficacy of magnetic field on the thermal behavior of MnFe2O4 nanofluid as a functional fluid through an open-cell metal foam tube

NASA Astrophysics Data System (ADS)

Amani, Mohammad; Ameri, Mohammad; Kasaeian, Alibakhsh

2017-06-01

In the present experimental study, the influence of permanent and alternating magnetic fields on the flow and thermal behavior of MnFe2O4 magnetic nanofluid flowing through a circular open-cell metal foam tube is investigated under homogeneous heat flux conditions. The experiments are performed at various nanoparticle concentrations, Reynolds numbers and magnetic fields with different strengths and frequencies. According to the observations, the heat transfer rate enhances directly relative to nanoparticle concentration and Reynolds number in attendance of magnetic field, whereas its maximum value of 16.4% is found for 2 wt% nanoparticles at Re = 200 under alternating field with 400 G strength and 20 Hz frequency. Moreover, it is observed that the influence of strength and frequency of magnetic field is insignificant for the pressure drop. Hydrothermal efficiency as the ratio of the Nusselt number to the ratio of the pressure drop is defined in order to evaluate the privilege of using MnFe2O4 nanofluids in practical applications. The maximum efficiency of 1.25 is observed at 2 wt% under magnetic field with 400 G and 20 Hz at Re = 1000.

Effects of isoconcentration surface threshold values on the characteristics of needle-shaped precipitates in atom probe tomography data from an aged Al-Mg-Si alloy.

PubMed

Aruga, Yasuhiro; Kozuka, Masaya

2016-04-01

Needle-shaped precipitates in an aged Al-0.62Mg-0.93Si (mass%) alloy were identified using a compositional threshold method, an isoconcentration surface, in atom probe tomography (APT). The influence of thresholds on the morphological and compositional characteristics of the precipitates was investigated. Utilizing optimum parameters for the concentration space, a reliable number density of the precipitates is obtained without dependence on the elemental concentration threshold in comparison with evaluation by transmission electron microscopy (TEM). It is suggested that careful selection of the concentration space in APT can lead to a reasonable average Mg/Si ratio for the precipitates. It was found that the maximum length and maximum diameter of the precipitates are affected by the elemental concentration threshold. Adjustment of the concentration threshold gives better agreement with the precipitate dimensions measured by TEM. © The Author 2015. Published by Oxford University Press on behalf of The Japanese Society of Microscopy. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Distribution and variability of nitrogen and phosphorus in the alluvial, High Plains, Rush Springs, and Blaine aquifers in western Oklahoma

USGS Publications Warehouse

Becker, C.J.

1994-01-01

Aquifers are the primary source of water for drinking and agricultural purposes in western Oklahoma. Health concerns about consuming nitrogen and an increased reliance on ground water for drinking necessitate a better understanding of the cause and effect of contamination from nutrients. The purpose of this project was to compile nutrients data from the National Water Information System data base for the alluvial aquifers west of longitude 98 degrees W. and from three bedrock aquifers, High Plains, Rush Springs, and Blaine, and provide this information in a report for future projects and for the facilitation of nutrient source management. The scope of the work consisted of (1) compiling ground-water quality data concerning nitrogen and phosphorus ions, (2) constructing boxplots illustrating data variability, (3) maps for each aquifer showing locations of wells when nitrogen and phosphorus ions were measured in ground water and where concentrations of nitrate and nitrite, reported as nitrogen, exceed the maximum contaminant level, and (4) calculating summary statistics. Nutrient data were obtained from the U.S. Geological Survey data base called the National Water Information System. Data were restricted to ground-water samples, but no restrictions were placed on well and water use or date and time of sampling. Compiled nutrient data consist of dissolved and total concentrations of the common nitrogen and phosphorus ions measured in ground water. For nitrogen these ions include nitrate, nitrite, ammonium, and nitrite plus nitrate. All concentrations are reported in milligrams per liter as nitrogen. Phosphorus in ground water is measured as the orthophosphate ion, and is reported in milligrams per liter as phosphorus. Nutrient variability is illustrated by a standard boxplot. The data are presented by aquifer or hydrologic subregion for alluvial aquifers, with one boxplot constructed for each nutrient compound if more than four analyses are present. Maps for each aquifer show where nitrogen and phosphorus have been measured in ground water and where the concentrations of nitrate and nitrite exceed the maximum contaminant level. A statistical summary for each aquifer and subregion show if censored data were present, number of samples in each data set, largest minimum reporting level for each nutrient compound, percentiles used to construct boxplots, and minimum and maximum values. Also given are the number of wells sampled in each aquifer and the number of wells exceeding the maximum contaminant level.

Effects of calibration methods on quantitative material decomposition in photon-counting spectral computed tomography using a maximum a posteriori estimator.

PubMed

Curtis, Tyler E; Roeder, Ryan K

2017-10-01

Advances in photon-counting detectors have enabled quantitative material decomposition using multi-energy or spectral computed tomography (CT). Supervised methods for material decomposition utilize an estimated attenuation for each material of interest at each photon energy level, which must be calibrated based upon calculated or measured values for known compositions. Measurements using a calibration phantom can advantageously account for system-specific noise, but the effect of calibration methods on the material basis matrix and subsequent quantitative material decomposition has not been experimentally investigated. Therefore, the objective of this study was to investigate the influence of the range and number of contrast agent concentrations within a modular calibration phantom on the accuracy of quantitative material decomposition in the image domain. Gadolinium was chosen as a model contrast agent in imaging phantoms, which also contained bone tissue and water as negative controls. The maximum gadolinium concentration (30, 60, and 90 mM) and total number of concentrations (2, 4, and 7) were independently varied to systematically investigate effects of the material basis matrix and scaling factor calibration on the quantitative (root mean squared error, RMSE) and spatial (sensitivity and specificity) accuracy of material decomposition. Images of calibration and sample phantoms were acquired using a commercially available photon-counting spectral micro-CT system with five energy bins selected to normalize photon counts and leverage the contrast agent k-edge. Material decomposition of gadolinium, calcium, and water was performed for each calibration method using a maximum a posteriori estimator. Both the quantitative and spatial accuracy of material decomposition were most improved by using an increased maximum gadolinium concentration (range) in the basis matrix calibration; the effects of using a greater number of concentrations were relatively small in magnitude by comparison. The material basis matrix calibration was more sensitive to changes in the calibration methods than the scaling factor calibration. The material basis matrix calibration significantly influenced both the quantitative and spatial accuracy of material decomposition, while the scaling factor calibration influenced quantitative but not spatial accuracy. Importantly, the median RMSE of material decomposition was as low as ~1.5 mM (~0.24 mg/mL gadolinium), which was similar in magnitude to that measured by optical spectroscopy on the same samples. The accuracy of quantitative material decomposition in photon-counting spectral CT was significantly influenced by calibration methods which must therefore be carefully considered for the intended diagnostic imaging application. © 2017 American Association of Physicists in Medicine.

Empowering Engineering Students through Employability Skills

ERIC Educational Resources Information Center

Kaushal, Urvashi

2016-01-01

A professional course program like engineering strives to get the maximum number of its students placed through campus interviews. While communication skills have been added in all the engineering courses with the aim to improve their performance in placement, the syllabus mostly concentrates on the development of four language skills. The…

Combinatoric analysis of heterogeneous stochastic self-assembly.

PubMed

D'Orsogna, Maria R; Zhao, Bingyu; Berenji, Bijan; Chou, Tom

2013-09-28

We analyze a fully stochastic model of heterogeneous nucleation and self-assembly in a closed system with a fixed total particle number M, and a fixed number of seeds Ns. Each seed can bind a maximum of N particles. A discrete master equation for the probability distribution of the cluster sizes is derived and the corresponding cluster concentrations are found using kinetic Monte-Carlo simulations in terms of the density of seeds, the total mass, and the maximum cluster size. In the limit of slow detachment, we also find new analytic expressions and recursion relations for the cluster densities at intermediate times and at equilibrium. Our analytic and numerical findings are compared with those obtained from classical mass-action equations and the discrepancies between the two approaches analyzed.

Photochemical modeling of emissions trading of highly reactive volatile organic compounds in Houston, Texas. 1. Reactivity based trading and potential for ozone hot spot formation.

PubMed

Wang, Linlin; Thompson, Tammy; McDonald-Buller, Elena C; Webb, Alba; Allen, David T

2007-04-01

As part of the State Implementation Plan for attaining the National Ambient Air Quality Standard for ozone, the Texas Commission of Environmental Quality has created a Highly Reactive Volatile Organic Compounds (HRVOC) Emissions Cap and Trade Program for industrial point sources in the Houston/Galveston/Brazoria area. This program has a number of unique features, including its focus on a limited group of ozone precursors and its provisions for trading emissions based on atmospheric reactivity. This series of papers examines the potential air quality impacts of this new emission trading program through photochemical modeling of potential trading scenarios; this first paper in the series describes the air quality modeling methods used to assess potential trades, the potential for localized increases in ozone concentrations (ozone "hot spots") due to HRVOC emission trading, and the use of reactivity scales in the trading. When HRVOC emissions are traded on a mass basis, the simulations indicate that trading of HRVOC allowances between facilities resulted in less than 0.15 ppb (<0.13%) and 0.06 ppb (<0.06%) increases in predicted maximum, area-wide 1-h averaged and 8-h averaged ozone concentrations, respectively. Maximum decreases in ozone concentrations associated with trading, as opposed to across-the-board reductions, were larger than the increases. All of these changes are small compared to the maximum changes in ozone concentrations due to the VOC emissions from these sources (up to 5-10 ppb for 8 h averages; up to 30 ppb for 1-h averages). When emissions of HRVOCs are traded for other, less reactive emissions, on a reactivity weighted basis, air quality simulations indicate that daily maximum ozone concentrations increased by less than 0.3%. Because these relatively small changes (< 1%) are for unlikely trading scenarios designed to produce a maximum change in ozone concentrations (all emissions traded into localized regions), the simulations indicate that the implementation of the trading program, as currently configured and possibly expanded, is unlikely to cause localized increases in ozone concentrations ("hot spots").

Maruhn-Greiner Maximum of Uranium Fission for Confirmation of Low Energy Nuclear Reactions LENR via a Compound Nucleus with Double Magic Numbers

NASA Astrophysics Data System (ADS)

Hora, H.; Miley, G. H.

2007-12-01

One of the most convincing facts about LENR due to deuterons of very high concentration in host metals as palladium is the measurement of the large scale minimum of the reaction probability depending on the nucleon number A of generated elements at A = 153 where a local maximum was measured. This is similar to the fission of uranium at A = 119 where the local maximum follows from the Maruhn-Greiner theory if the splitting nuclei are excited to about MeV energy. The LENR generated elements can be documented any time after the reaction by SIMS or K-shell X-ray excitation to show the very unique distribution with the local maximum. An explanation is based on the strong Debye screening of the Maxwellian deuterons within the degenerate rigid electron background especially within the swimming electron layer at the metal surface or at interfaces. The deuterons behave like neutrals at distances of about 2 picometers. They may form clusters due to soft attraction in the range above thermal energy. Clusters of 10 pm diameter may react over long time probabilities (megaseconds) with Pd nuclei leading to a double magic number compound nucleus which splits like in fission to the A = 153 element distribution.

Overall heat transfer coefficient and pressure drop in a typical tubular exchanger employing alumina nano-fluid as the tube side hot fluid

NASA Astrophysics Data System (ADS)

Kabeel, A. E.; Abdelgaied, Mohamed

2016-08-01

Nano-fluids are used to improve the heat transfer rates in heat exchangers, especially; the shell-and-tube heat exchanger that is considered one of the most important types of heat exchangers. In the present study, an experimental loop is constructed to study the thermal characteristics of the shell-and-tube heat exchanger; at different concentrations of Al2O3 nonmetallic particles (0.0, 2, 4, and 6 %). This material concentrations is by volume concentrations in pure water as a base fluid. The effects of nano-fluid concentrations on the performance of shell and tube heat exchanger have been conducted based on the overall heat transfer coefficient, the friction factor, the pressure drop in tube side, and the entropy generation rate. The experimental results show that; the highest heat transfer coefficient is obtained at a nano-fluid concentration of 4 % of the shell side. In shell side the maximum percentage increase in the overall heat transfer coefficient has reached 29.8 % for a nano-fluid concentration of 4 %, relative to the case of the base fluid (water) at the same tube side Reynolds number. However; in the tube side the maximum relative increase in pressure drop has recorded the values of 12, 28 and 48 % for a nano-material concentration of 2, 4 and 6 %, respectively, relative to the case without nano-fluid, at an approximate value of 56,000 for Reynolds number. The entropy generation reduces with increasing the nonmetallic particle volume fraction of the same flow rates. For increase the nonmetallic particle volume fraction from 0.0 to 6 % the rate of entropy generation decrease by 10 %.

Calibration methods influence quantitative material decomposition in photon-counting spectral CT

NASA Astrophysics Data System (ADS)

Curtis, Tyler E.; Roeder, Ryan K.

2017-03-01

Photon-counting detectors and nanoparticle contrast agents can potentially enable molecular imaging and material decomposition in computed tomography (CT). Material decomposition has been investigated using both simulated and acquired data sets. However, the effect of calibration methods on material decomposition has not been systematically investigated. Therefore, the objective of this study was to investigate the influence of the range and number of contrast agent concentrations within a modular calibration phantom on quantitative material decomposition. A commerciallyavailable photon-counting spectral micro-CT (MARS Bioimaging) was used to acquire images with five energy bins selected to normalize photon counts and leverage the contrast agent k-edge. Material basis matrix values were determined using multiple linear regression models and material decomposition was performed using a maximum a posteriori estimator. The accuracy of quantitative material decomposition was evaluated by the root mean squared error (RMSE), specificity, sensitivity, and area under the curve (AUC). An increased maximum concentration (range) in the calibration significantly improved RMSE, specificity and AUC. The effects of an increased number of concentrations in the calibration were not statistically significant for the conditions in this study. The overall results demonstrated that the accuracy of quantitative material decomposition in spectral CT is significantly influenced by calibration methods, which must therefore be carefully considered for the intended diagnostic imaging application.

Stratospheric Ozone Climatology from Lidar Measurements at Table Mountain (34.0 deg N, 117.7 deg W) and Mauna Loa (19.5 deg N, 155.6 deg W)

NASA Technical Reports Server (NTRS)

Leblanc, T.; McDermid, I. S.

2000-01-01

Using more than 1600 nighttime profiles obtained by the JPL differential absorption lidars (DIAL) located at Table Mountain Facility (TMF, 34.4 N) and Mauna Loa Observatory (MLO, 19.5 N) is presented in this paper. These two systems have been providing high-resolution vertical profiles of ozone number density between 15-50 km, several nights a week since 1989 (TMF) and 1993 (MLO). The climatology presented here is typical of early night ozone values with only a small influence of the Pinatubo aerosols and the 11-year solar cycle. The observed seasonal and vertical structure of the ozone concentration at TMF is consistent with that typical of mid- to subtropical latitudes. A clear annual cycle in opposite phase below and above the ozone concentration peak is observed. The observed winter maximum below the ozone peak is associated with a maximum day-to-day variability, typical of a dynamically driven lower stratosphere. The maximum concentration observed in summer above the ozone peak emphasizes the more dominant role of photochemistry. Unlike TMF, the ozone concentration observed at MLO tends to be higher during the summer months and lower during the winter months throughout the entire stratospheric ozone layer. Only a weak signature of the extra-tropical latitudes is observed near 19-20 km, with a secondary maximum in late winter. The only large variability observed at MLO is associated with the natural variability of the tropical tropopause.

Estimating the capacity value of concentrating solar power plants: A case study of the southwestern United States

DOE PAGES

Madaeni, Seyed Hossein; Sioshansi, Ramteen; Denholm, Paul

2012-01-27

Here, we estimate the capacity value of concentrating solar power (CSP) plants without thermal energy storage in the southwestern U.S. Our results show that CSP plants have capacity values that are between 45% and 95% of maximum capacity, depending on their location and configuration. We also examine the sensitivity of the capacity value of CSP to a number of factors and show that capacity factor-based methods can provide reasonable approximations of reliability-based estimates.

Toxicity to woodlice of zinc and lead oxides added to soil litter

USGS Publications Warehouse

Beyer, W.N.; Anderson, A.

1985-01-01

Previous studies have shown that high concentrations of metals in soil are associated with reductions in decomposer populations. We have here determined the relation between the concentrations of lead and zinc added as oxides to soil litter and the survival and reproduction of a decomposer population under controlled conditions. Laboratory populations of woodlice (Porcellio scaber Latr) were fed soil litter treated with lead or zinc at concentrations that ranged from 100 to 12,800 ppm. The survival of the adults, the maximum number of young alive, and the average number of young alive, were recorded over 64 weeks. Lead at 12,800 ppm and zinc at 1,600 ppm or more had statistically significant (p < 0.05) negative effects on the populations. These results agree with field observations suggesting that lead and zinc have reduced populations of decomposers in contaminated forest soil litter, and concentrations are similar to those reported to be associated with reductions in natural populations of decomposers. Poisoning of decomposers may disrupt nutrient cycling, reduce the numbers of invertebrates available to other wildlife for food, and contribute to the contamination of food chains.

Measurement of Turbulent Fluxes of Swirling Flow in a Scaled Up Multi Inlet Vortex Reactor

NASA Astrophysics Data System (ADS)

Olsen, Michael; Hitimana, Emmanual; Hill, James; Fox, Rodney

2017-11-01

The multi-inlet vortex reactor (MIVR) has been developed for use in the FlashNanoprecipitation (FNP) process. The MIVR has four identical square inlets connected to a central cylindrical mixing chamber with one common outlet creating a highly turbulent swirling flow dominated by a strong vortex in the center. Efficient FNP requires rapid mixing within the MIVR. To investigate the mixing, instantaneous velocity and concentration fields were acquired using simultaneous stereoscopic particle image velocimetry and planar laser-induced fluorescence. The simultaneous velocity and concentration data were used to determine turbulent fluxes and spatial cross-correlations of velocity and concentration fluctuations. The measurements were performed for four inlet flow Reynolds numbers (3250, 4875, 6500, and 8125) and at three measurement planes within the reactor. A correlation between turbulent fluxes and vortex strength was found. For all Reynolds numbers, turbulent fluxes are maximum in the vortex dominated central region of the reactor and decay away from the vortex. Increasing Reynolds number increased turbulent fluxes and subsequently enhanced mixing. The mixing performance was confirmed by determining coefficients of concentration variance within the reactor.

Algal conditions in the Caloosahatchee River (1975-79), Lake Okeechobee to Franklin Lock, Florida

USGS Publications Warehouse

McPherson, Benjamin F.; La Rose, Henry R.

1982-01-01

Maximum numbers of suspended algae occurred in late spring and early summer, in each of the years 1975-79, in the Caloosahatchee River. Numbers exceeded 100,000 cells per milliliter at all stations sometime during the study. Concentrations decreased during late summer and autumn and were low during winter, except in January 1979 when numbers at most sites exceeded 100,000 cells per milliliter. The January 1979 bloom coincided with large discharges from Lake Okeechobee. During previous winters, discharges and algal numbers were lower. During other seasons, algal blooms occurred most frequently under low-flow or stagnant conditions. The upstream site at Moore Haven, which had the least discharge and was most stagnant, had consistently higher algal concentrations than downstream sites. Blue-green algae were dominant in the river during the summer at the upstream site throughout the year. The percentage of blue-green algae decreased downstream. Concentrations of nitrite plus nitrate nitrogen were inversely correlated with concentrations of algae and decreased to near zero during algal blooms. The low concentrations of these forms of inorganic nitrogen relative to other major nutrients probably favor blue-green algae and limit growth of other algae. Contributions by the basin tributaries to the nutritive condition of the river were small because concentrations of nutrients, algal growth potential, and algae in the tributaries were generally less than those in the river. (USGS)

Watershed Regressions for Pesticides (WARP) for Predicting Annual Maximum and Annual Maximum Moving-Average Concentrations of Atrazine in Streams

USGS Publications Warehouse

Stone, Wesley W.; Gilliom, Robert J.; Crawford, Charles G.

2008-01-01

Regression models were developed for predicting annual maximum and selected annual maximum moving-average concentrations of atrazine in streams using the Watershed Regressions for Pesticides (WARP) methodology developed by the National Water-Quality Assessment Program (NAWQA) of the U.S. Geological Survey (USGS). The current effort builds on the original WARP models, which were based on the annual mean and selected percentiles of the annual frequency distribution of atrazine concentrations. Estimates of annual maximum and annual maximum moving-average concentrations for selected durations are needed to characterize the levels of atrazine and other pesticides for comparison to specific water-quality benchmarks for evaluation of potential concerns regarding human health or aquatic life. Separate regression models were derived for the annual maximum and annual maximum 21-day, 60-day, and 90-day moving-average concentrations. Development of the regression models used the same explanatory variables, transformations, model development data, model validation data, and regression methods as those used in the original development of WARP. The models accounted for 72 to 75 percent of the variability in the concentration statistics among the 112 sampling sites used for model development. Predicted concentration statistics from the four models were within a factor of 10 of the observed concentration statistics for most of the model development and validation sites. Overall, performance of the models for the development and validation sites supports the application of the WARP models for predicting annual maximum and selected annual maximum moving-average atrazine concentration in streams and provides a framework to interpret the predictions in terms of uncertainty. For streams with inadequate direct measurements of atrazine concentrations, the WARP model predictions for the annual maximum and the annual maximum moving-average atrazine concentrations can be used to characterize the probable levels of atrazine for comparison to specific water-quality benchmarks. Sites with a high probability of exceeding a benchmark for human health or aquatic life can be prioritized for monitoring.

Extract of Pelargonium sidoides (EPs 7630) improves phagocytosis, oxidative burst, and intracellular killing of human peripheral blood phagocytes in vitro.

PubMed

Conrad, Andreas; Hansmann, Cathrin; Engels, Inge; Daschner, Franz D; Frank, Uwe

2007-01-01

Clinical data show that EPs 7630, an aqueous ethanolic extract from the roots of Pelargonium sidoides, can be used for the treatment of upper respiratory tract infections (URTI). The biological effects of the preparation have not been fully investigated. The objective of this study was to examine the impact of EPs 7630 on the activity of human peripheral blood phagocytes (PBP). A whole blood-based, flow cytometric assay was used to simultaneously assess phagocytosis and oxidative burst. Calcein-AM stained Candida albicans (DSM 1386) were used as target organisms. Oxidative burst was measured by addition of dihydroethidium (DHE). Target organisms and whole blood were co-incubated and analyzed after 0, 2, 4, 6, 10, and 30 min. Intracellular killing of the target organisms was evaluated by determining the number of surviving yeast cells after co-incubation of C. albicans and human whole blood. EPs 7630 was applied in therapeutically relevant concentrations between 0 and 30 microg/ml. Compared with controls EPs 7630 increased the number of phagocytosing PBP during the observed time points between 2 and 10 min in a concentration-dependent manner, with a maximum enhancement of 56% at 2 min (p=0.002). The application of EPs 7630 also led to a significant increase in the number of burst-active PBP for all time points observed beyond 2 min (p<0.001). The maximum augmentation was 120% after application of 30 microg/ml EPs 7630 at 4 min. Using a microbiological assay, intracellular killing was also enhanced by EPs 7630. This was expressed by a significant reduction in the number of surviving target organisms (p<0.001). The maximum reduction in viable yeast cells (-31%) was observed after co-incubation for 120 min with the highest concentration of EPs 7630 (30 microg/ml). In conclusion, the positive effects of EPs 7630 on phagocytosis, oxidative burst, and intracellular killing of yeast cells as test organisms are important components of the compound's biological activity. Our findings constitute a valuable contribution to understanding the clinical effects of EPs 7630.

Leaf Optical Properties in Higher Plants: Linking Spectral Characteristics to Stress and Chlorophyll Concentration

NASA Technical Reports Server (NTRS)

Carter, Gregory A.; Knapp, Alan K.

2000-01-01

A number of studies have linked responses in leaf spectral reflectance, transmittance or absorptance to physiological stress. A variety of stressors including dehydration, flooding,freezing, ozone, herbicides, competition, disease, insects and deficiencies in ectomycorrhizal development and N fertilization have been imposed on species ranging from grasses to conifers and deciduous trees. In this cases, the maximum difference in reflectance within the 400 - 850 nm wavelength range between control and stressed states occurred as a reflectance increase at wavelength near 700 nm. In studies that included transmittance and absorptance as well as reflectance, maximum differences occurred as increases and decreases, respectively, near 700 nm. This common optical response to stress could be simulated closely by varying the chlorophyll concentrations in senescent leaves of five species. The optical response to stress near 700 nm, as well as corresponding changes in reflectance that occur in the green-yellow spectrum, can be explained by the general tendency of stress to reduce leaf chlorophyll concentration.

Concentrations of selected pharmaceuticals and antibiotics in south-central Pennsylvania waters, March through September 2006

USGS Publications Warehouse

Loper, Connie A.; Crawford, J. Kent; Otto, Kim L.; Manning, Rhonda L.; Meyer, Michael T.; Furlong, Edward T.

2007-01-01

This report presents environmental and quality-control data from analyses of 15 pharmaceutical and 31 antibiotic compounds in water samples from streams and wells in south-central Pennsylvania. The analyses are part of a study by the U.S. Geological Survey (USGS) in cooperation with the Pennsylvania Department of Environmental Protection (PADEP) to define concentrations of selected emerging contaminants in streams and well water in Pennsylvania. Sampling was conducted at 11 stream sites and at 6 wells in 9 counties of south-central Pennsylvania. Five of the streams received municipal wastewater and 6 of the streams received runoff from agricultural areas dominated by animal-feeding operations. For all 11 streams, samples were collected at locations upstream and downstream of the municipal effluents or animal-feeding operations. All six wells were in agricultural settings. A total of 120 environmental samples and 21 quality-control samples were analyzed for the study. Samples were collected at each site in March/April, May, July, and September 2006 to obtain information on changes in concentration that could be related to seasonal use of compounds.For streams, 13 pharmaceuticals and 11 antibiotics were detected at least 1 time. Detections included analytical results that were estimated or above the minimum reporting limits. Seventy-eight percent of all detections were analyzed in samples collected downstream from municipal-wastewater effluents. For streams receiving wastewater effluents, the pharmaceuticals caffeine and para-xanthine (a degradation product of caffeine) had the greatest concentrations, 4.75 μg/L (micrograms per liter) and 0.853 μg/L, respectively. Other pharmaceuticals and their respective maximum concentrations were carbamazepine (0.516 μg/L) and ibuprofen (0.277 μg/L). For streams receiving wastewater effluents, the antibiotic azithromycin had the greatest concentration (1.65 μg/L), followed by sulfamethoxazole (1.34 μg/L), ofloxacin (0.329 μg/L), and trimethoprim (0.256 μg/L).For streams receiving runoff from animal-feeding operations, the only pharmaceuticals detected were acetaminophen, caffeine, cotinine, diphenhydramine, and carbamazepine. The maximum concentration for pharmaceuticals was 0.053 μg/L. Three streams receiving runoff from animal-feeding operations had detections of one or more antibiotic compound--oxytetracycline, sulfadimethoxine, sulfamethoxazole, and tylosin. The maximum concentration for antibiotics was 0.157 μg/L. The average number of compounds (pharmaceuticals and antibiotics) detected in sites downstream from animal-feeding operations was three. The average number of compounds detected downstream from municipal-wastewater effluents was 13.For wells used to supply livestock, four compounds were detected--two pharmaceuticals (cotinine and diphenhydramine) and two antibiotics (tylosin and sulfamethoxazole). There were five detections in all the well samples. The maximum concentration detected in well water was for cotinine, estimated to be 0.024 μg/L.Seasonal occurrence of pharmaceutical and antibiotic compounds in stream water varied by compound and site type. At four stream sites, the same compounds were detected in all four seasonal samples. At other sites, pharmaceutical or antibiotic compounds were detected only one time in seasonal samples. Winter samples collected in streams receiving municipalwastewater effluent had the greatest number of compounds detected (21). Research analytical methods were used to determine concentrations for pharmaceuticals and antibiotics. To assist in evaluating the quality of the analyses, detailed information is presented on laboratory methodology and results from qualitycontrol samples. Quality-control data include results for nine blanks, nine duplicate environmental sample pairs, and three laboratory-spiked environmental samples as well as the recoveries of compounds in laboratory surrogates and laboratory reagent spikes.

Maruhn-Greiner Maximum for Confirmation of Low Energy Nuclear Reactions (LENR) via a Compound Nucleus with Double Magic Numbers

NASA Astrophysics Data System (ADS)

Hora, Heinrich; Miley, George

2007-03-01

One of the most convincing facts about LENR due to deuterons (ds) or protons of very high concentration in host metals of palladium is the measurement of the large scale minimum in the reaction probability with product elements centered around the nucleon number A = 153. The local maximum was measured in this region is similar to fission of uranium at A = 119 where the local maximum follows the Maruhn-Greiner mechanism^1. We suggest this phenomenon can be explained by the strong screening of the Maxwellian ds on the degenerate rigid electron background within the swimming electrons at the metal surface or thin filem interfaces. The deuterons behave like neutrals at distances of above 2 picometers (pm) and form clusters due to soft attraction in the range of thermal energy; 10 pm diameter clusters can react over long time scales (10^6 s) with Pd leading to double magic number compound nuclei 306x126 decaying via fission to an A=153 element distribution. J. Maruhn et al, Phys. Rev. Letters 32, 548 (1974) H. Hora, G.H. Miley, CzechJ. Phys. 48, 1111 (1998)

Exospheric hydrogen above St-Santin /France/

NASA Technical Reports Server (NTRS)

Derieux, A.; Lejeune, G.; Bauer, P.

1975-01-01

The temperature and hydrogen concentration of the exosphere was determined using incoherent scatter measurements performed above St. Santin from 1969 to 1972. The hydrogen concentration was deduced from measurements of the number density of positive hydrogen and oxygen ions. A statistical analysis is given of the hydrogen concentration as a function of the exospheric temperature and the diurnal variation of the hydrogen concentration is investigated for a few selected days of good quality observation. The data averaged with respect to the exospheric temperature without consideration of the local time exhibits a distribution consistent with a constant effective Jeans escape flux of about 9 x 10 to the 7 cu cm/s. The local time variation exhibits a maximum to minimum concentration ratio of at least 3.5.

Experimental study of laminar forced convective heat transfer of deionized water based copper (I) oxide nanofluids in a tube with constant wall heat flux

NASA Astrophysics Data System (ADS)

Umer, Asim; Naveed, Shahid; Ramzan, Naveed

2016-10-01

Nanofluids, having 1-100 nm size particles in any base fluid are promising fluid for heat transfer intensification due to their enhanced thermal conductivity as compared with the base fluid. The forced convection of nanofluids is the major practical application in heat transfer equipments. In this study, heat transfer enhancements at constant wall heat flux under laminar flow conditions were investigated. Nanofluids of different volume fractions (1, 2 and 4 %) of copper (I) oxide nanoparticles in deionized water were prepared using two step technique under mechanical mixing and ultrasonication. The results were investigated by increasing the Reynolds number of the nanofluids at constant heat flux. The trends of Nusselt number variation with dimensionless length (X/D) and Reynolds numbers were studied. It was observed that heat transfer coefficient increases with increases particles volume concentration and Reynolds number. The maximum enhancement in heat transfer coefficient of 61 % was observed with 4 % particle volume concentration at Reynolds number (Re ~ 605).

Biomass Burning Organic Aerosol as a Modulator of Droplet Number in the Southern Atlantic

NASA Astrophysics Data System (ADS)

Kacarab, M.; Howell, S. G.; Small Griswold, J. D.; Thornhill, K. L., II; Wood, R.; Redemann, J.; Nenes, A.

2017-12-01

Aerosols play a significant yet highly variable role in local and global air quality and climate. They act as cloud condensation nuclei (CCN) and both scatter and absorb radiation, lending a large source of uncertainty to climate predictions. Biomass burning organic aerosol (BBOA) can drastically elevate CCN concentrations, but the response in cloud droplet number may be suppressed or even reversed due to low supersaturations that develop from strong competition for water vapor. Constraining droplet response to BBOA is a key factor to understanding aerosol-cloud interactions. The southeastern Atlantic (SEA) cloud deck off the west coast of central Africa is a prime opportunity to study these cloud-BBOA interactions for marine stratocumulus as during winter in the southern hemisphere the SEA cloud deck is overlain by a large, optically thick BBOA plume. The NASA ObseRvations of Aerosols above Clouds and their intEractionS (ORACLES) study focuses on increasing the understanding of how these BBOA affect the SEA cloud deck. Measurements of CCN concentration, aerosol size distribution and composition, updraft velocities, and cloud droplet number in and around the SEA cloud deck and associated BBOA plume were taken aboard the NASA P-3 aircraft during the first two years of the ORACLES campaign in September 2016 and August 2017. Here we evaluate the predicted and observed droplet number sensitivity to the aerosol fluctuations and quantify, using the data, the drivers of droplet number variability (vertical velocity or aerosol properties) as a function of biomass burning plume characteristics. Over the course of the campaign, different levels of BBOA influence in the marine boundary layer (MBL) were observed, allowing for comparison of cloud droplet number, hygroscopicity parameter (κ), and maximum in-cloud supersaturation over a range of "clean" and "dirty" conditions. Droplet number sensitivity to aerosol concentration, κ, and vertical updraft velocities are also evaluated. Generally, an increase in BBOA led to increased droplet number along with decreased κ and maximum in-cloud supersaturation (leading to an increase in competition for water vapor). This work seeks to contribute to an increased understanding of how CCN and aerosol properties affect the radiative and hydrological properties and impact of the cloud.

[Isothiazolinones as causal factors of contact allergy epidemics in the 20th and 21st centuries].

PubMed

Chomiczewska-Skóra, Dorota; Kręcisz, Beata; Kieć-Świerczyńska, Marta

2014-01-01

Chloromethylisothiazolinone (MCI) and methylisothiazolinone (MI) have been widely used as preservatives in cosmetics, household products and industrial products since the late 1970s. First cases of contact allergy to the MCI/MI combination were noted in 1980-1982 in Sweden. Then, a significant increase in the frequency of sensitization to these compounds was observed in many European centers. The increase has been stopped by the introduction of legislation on their maximum concentrations in consumer and industrial products in Europe and in some non-European countries. But approval of the use of MI alone without limits in industrial products (from 2000) and at a maximum concentration of 100 ppm in cosmetics (from 2005) resulted in an unprecedented increase in the number of individuals sensitized to this compound. Allergic contact dermatitis due to MI occurs in both adults and children. It is often manifested by severe symptoms, which may be also induced by airborne exposure. The most important sources of sensitization include cosmetic products and paints. To counteract the increasing problem of contact allergy epidemic to MI, the recommendations have been developed, suggesting the ban on the use of MI in "leave-on" cosmetics and maximum concentration of 15 ppm in "rinse-off" products. The recommendations are likely to be implemented in 2014.

Retrieval of sodium number density profiles in the mesosphere and lower thermosphere from SCIAMACHY limb emission measurements

NASA Astrophysics Data System (ADS)

Langowski, M. P.; von Savigny, C.; Burrows, J. P.; Rozanov, V. V.; Dunker, T.; Hoppe, U.-P.; Sinnhuber, M.; Aikin, A. C.

2015-07-01

An algorithm has been developed for the retrieval of sodium atom (Na) number density on a latitude and altitude grid from SCIAMACHY limb measurements of the Na resonance fluorescence. The results are obtained between 50 and 150 km altitude and the resulting global seasonal variations of Na are analysed. The retrieval approach is adapted from that used for the retrieval of magnesium atom (Mg) and magnesium ion (Mg+) number density profiles recently reported by Langowski et al. (2014). Monthly mean values of Na are presented as a function of altitude and latitude. This data set was retrieved from the 4 years of spectroscopic limb data of the SCIAMACHY mesosphere and lower thermosphere (MLT) measurement mode. The Na layer has a nearly constant altitude of 90-93 km for all latitudes and seasons, and has a full width at half maximum of 5-15 km. Small but substantial seasonal variations in Na are identified for latitudes less than 40°, where the maximum Na number densities are 3000-4000 atoms cm-3. At mid to high latitudes a clear seasonal variation with a winter maximum of up to 6000 atoms cm-3 is observed. The high latitudes, which are only measured in the Summer Hemisphere, have lower number densities with peak densities being approximately 1000 Na atoms cm-3. The full width at half maximum of the peak varies strongly at high latitudes and is 5 km near the polar summer mesopause, while it exceeds 10 km at lower latitudes. In summer the Na atom concentration at high latitudes and at altitudes below 88 km is significantly smaller than that at mid latitudes. The results are compared with other observations and models and there is overall a good agreement with these.

Experimental investigation of TiO2/water nanofluid laminar forced convective heat transfer through helical coiled tube

NASA Astrophysics Data System (ADS)

Kahani, M.; Zeinali Heris, S.; Mousavi, S. M.

2014-05-01

Coiled tubes and nanofludics are two significant techniques to enhance the heat transfer ability of thermal equipments. The forced convective heat transfer and the pressure drop of nanofluid inside straight tube and helical coiled one with a constant wall heat flux were studied experimentally. Distilled water was used as a host fluid and Nanofluids of aqueous TiO2 nanoparticles (50 nm) suspensions were prepared in various volume concentrations of 0.25-2 %. The heat transfer coefficient of nanofluids is obtained for different nanoparticle concentrations as well as various Reynolds numbers. The experiments covered a range of Reynolds number of 500-4,500. The results show the considerable enhancement of heat transfer rate, which is due to the nanoparticles present in the fluid. Heat transfer coefficient increases by increasing the volume concentration of nanoparticles as well as Reynolds number. Moreover, due to the curvature of the tube when fluid flows inside helical coiled tube instead of straight one, both convective heat transfer coefficient and the pressure drop of fluid grow considerably. Also, the thermal performance factors for tested nanofluids are greater than unity and the maximum thermal performance factor of 3.72 is found with the use of 2.0 % volume concentration of nanofluid at Reynolds number of 1,750.

Maximum urine concentrating capability in a mathematical model of the inner medulla of the rat kidney.

PubMed

Marcano, Mariano; Layton, Anita T; Layton, Harold E

2010-02-01

In a mathematical model of the urine concentrating mechanism of the inner medulla of the rat kidney, a nonlinear optimization technique was used to estimate parameter sets that maximize the urine-to-plasma osmolality ratio (U/P) while maintaining the urine flow rate within a plausible physiologic range. The model, which used a central core formulation, represented loops of Henle turning at all levels of the inner medulla and a composite collecting duct (CD). The parameters varied were: water flow and urea concentration in tubular fluid entering the descending thin limbs and the composite CD at the outer-inner medullary boundary; scaling factors for the number of loops of Henle and CDs as a function of medullary depth; location and increase rate of the urea permeability profile along the CD; and a scaling factor for the maximum rate of NaCl transport from the CD. The optimization algorithm sought to maximize a quantity E that equaled U/P minus a penalty function for insufficient urine flow. Maxima of E were sought by changing parameter values in the direction in parameter space in which E increased. The algorithm attained a maximum E that increased urine osmolality and inner medullary concentrating capability by 37.5% and 80.2%, respectively, above base-case values; the corresponding urine flow rate and the concentrations of NaCl and urea were all within or near reported experimental ranges. Our results predict that urine osmolality is particularly sensitive to three parameters: the urea concentration in tubular fluid entering the CD at the outer-inner medullary boundary, the location and increase rate of the urea permeability profile along the CD, and the rate of decrease of the CD population (and thus of CD surface area) along the cortico-medullary axis.

[MAXIMUM SINGLE DOSE OF COLLOIDAL SILVER NEGATIVELY AFFECTS ERYTHROPOIESIS IN VITRO].

PubMed

Tishevskayal, N V; Zakharovl, Y M; Bolotovl, A A; Arkhipenko, Yu V; Sazontova, T G

2015-01-01

Erythroblastic islets (EI) of rat bone marrow were cultured for 24 h in the presence of silver nanoparticles (1.07 · 10(-4) mg/ml; 1.07 · 10(-3) mg/ml; and 1.07 · 10(-2) mg/mL). The colloidal silver at 1.07 · 10(-3) mg/ml concentration inhibited the formation of new Elby disrupting contacts of bone marrow macrophages with CFU-E (erythropoiesis de novo) by 65.3% (p < 0.05). Colloidal silver nanoparticles suppressed the reconstruction of erythropoiesis and inhibited the formation of new EI by disrupting contacts of CFU-E and central macrophages with matured erythroidal "crown" (erythropoiesis de repeto). The colloidal silver concentration of 1.07 · 10(-3) mg/ml in the culture medium also reduced the number of self-reconstructing EI by 67.5% (p <0.05), whereas 1.07 · 10(-2) mg/ml colloidal silver reduced this value by 93.7% (p < 0.05). Silver nanoparticles retarded maturation of erythroid cells at the stage of oxiphylic normoblast denucleation: 1.07 · 10(-3) mg/ml colloidal silver increased the number of mature El by 53% (p < 0.05). The retardation of erythropoiesis by colloidal silver in concentration equivalent to the maximum single dose is related to the effect of silver nanoparticles rather than glycerol present in the colloidal suspension.

The Effect of Heat Stress on Tomato Pollen Characteristics is Associated with Changes in Carbohydrate Concentration in the Developing Anthers

PubMed Central

PRESSMAN, ETAN; PEET, MARY M.; PHARR, D. MASON

2002-01-01

Continuous exposure of tomato ‘Trust’ to high temperatures (day/night temperatures of 32/26 °C) markedly reduced the number of pollen grains per flower and decreased viability. The effect of heat stress on pollen viability was associated with alterations in carbohydrate metabolism in various parts of the anther during its development. Under control, favourable temperature conditions (28/22 °C), starch accumulated in the pollen grains, where it reached a maximum value 3 d before anthesis; it then diminished towards anthesis. During anther development, the concentration of total soluble sugars gradually increased in the anther walls and in the pollen grains (but not in the locular fluid), reaching a maximum at anthesis. Continuous exposure of the plants to high temperatures (32/26 °C) prevented the transient increase in starch concentration and led to decreases in the concentrations of soluble sugars in the anther walls and the pollen grains. In the locular fluid, however, a higher soluble sugar concentration was detected under the high‐temperature regime throughout anther development. These results suggest that a major effect of heat stress on pollen development is a decrease in starch concentration 3 d before anthesis, which results in a decreased sugar concentration in the mature pollen grains. These events possibly contribute to the decreased pollen viability in tomato. PMID:12466104

40 CFR Table 1 to Subpart A of... - Maximum Concentration of Constituents for Groundwater Protection

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Maximum Concentration of Constituents for Groundwater Protection 1 Table 1 to Subpart A of Part 192 Protection of Environment ENVIRONMENTAL... Concentration of Constituents for Groundwater Protection Constituent concentration 1 Maximum Arsenic 0.05 Barium...

40 CFR Table 1 to Subpart A of... - Maximum Concentration of Constituents for Groundwater Protection

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 26 2013-07-01 2013-07-01 false Maximum Concentration of Constituents for Groundwater Protection 1 Table 1 to Subpart A of Part 192 Protection of Environment ENVIRONMENTAL... Concentration of Constituents for Groundwater Protection Constituent concentration 1 Maximum Arsenic 0.05 Barium...

40 CFR Table 1 to Subpart A of... - Maximum Concentration of Constituents for Groundwater Protection

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 26 2012-07-01 2011-07-01 true Maximum Concentration of Constituents for Groundwater Protection 1 Table 1 to Subpart A of Part 192 Protection of Environment ENVIRONMENTAL... Concentration of Constituents for Groundwater Protection Constituent concentration 1 Maximum Arsenic 0.05 Barium...

40 CFR Table 1 to Subpart A of... - Maximum Concentration of Constituents for Groundwater Protection

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 25 2011-07-01 2011-07-01 false Maximum Concentration of Constituents for Groundwater Protection 1 Table 1 to Subpart A of Part 192 Protection of Environment ENVIRONMENTAL... Concentration of Constituents for Groundwater Protection Constituent concentration 1 Maximum Arsenic 0.05 Barium...

Citric acid production from partly deproteinized whey under non-sterile culture conditions using immobilized cells of lactose-positive and cold-adapted Yarrowia lipolytica B9.

PubMed

Arslan, Nazli Pinar; Aydogan, Mehmet Nuri; Taskin, Mesut

2016-08-10

The present study was performed to produce citric acid (CA) from partly deproteinized cheese whey (DPCW) under non-sterile culture conditions using immobilized cells of the cold-adapted and lactose-positive yeast Yarrowia lipolytica B9. DPCW was prepared using the temperature treatment of 90°C for 15min. Sodium alginate was used as entrapping agent for cell immobilization. Optimum conditions for the maximum CA production (33.3g/L) in non-sterile DPCW medium were the temperature of 20°C, pH 5.5, additional lactose concentration of 20g/L, sodium alginate concentration of 2%, number of 150 beads/100mL and incubation time of 120h. Similarly, maximum citric acid/isocitric acid (CA/ICA) ratio (6.79) could be reached under these optimal conditions. Additional nitrogen and phosphorus sources decreased CA concentration and CA/ICA ratio. Immobilized cells were reused in three continuous reaction cycles without any loss in the maximum CA concentration. The unique combination of low pH and temperature values as well as cell immobilization procedure could prevent undesired microbial contaminants during CA production. This is the first work on CA production by cold-adapted microorganisms under non-sterile culture conditions. Besides, CA production using a lactose-positive strain of the yeast Y. lipolytica was investigated for the first time in the present study. Copyright © 2016 Elsevier B.V. All rights reserved.

Evaluation of methods for measuring particulate matter emissions from gas turbines.

PubMed

Petzold, Andreas; Marsh, Richard; Johnson, Mark; Miller, Michael; Sevcenco, Yura; Delhaye, David; Ibrahim, Amir; Williams, Paul; Bauer, Heidi; Crayford, Andrew; Bachalo, William D; Raper, David

2011-04-15

The project SAMPLE evaluated methods for measuring particle properties in the exhaust of aircraft engines with respect to the development of standardized operation procedures for particulate matter measurement in aviation industry. Filter-based off-line mass methods included gravimetry and chemical analysis of carbonaceous species by combustion methods. Online mass methods were based on light absorption measurement or used size distribution measurements obtained from an electrical mobility analyzer approach. Number concentrations were determined using different condensation particle counters (CPC). Total mass from filter-based methods balanced gravimetric mass within 8% error. Carbonaceous matter accounted for 70% of gravimetric mass while the remaining 30% were attributed to hydrated sulfate and noncarbonaceous organic matter fractions. Online methods were closely correlated over the entire range of emission levels studied in the tests. Elemental carbon from combustion methods and black carbon from optical methods deviated by maximum 5% with respect to mass for low to medium emission levels, whereas for high emission levels a systematic deviation between online methods and filter based methods was found which is attributed to sampling effects. CPC based instruments proved highly reproducible for number concentration measurements with a maximum interinstrument standard deviation of 7.5%.

How Well Does Dual-Energy Computed Tomography With Metal Artifact Reduction Software Improve Image Quality and Quantify Computed Tomography Number and Iodine Concentration?

PubMed

Ohira, Shingo; Kanayama, Naoyuki; Wada, Kentaro; Karino, Tsukasa; Nitta, Yuya; Ueda, Yoshihiro; Miyazaki, Masayoshi; Koizumi, Masahiko; Teshima, Teruki

2018-04-02

The objective of this study was to assess the accuracy of the quantitative measurements obtained using dual-energy computed tomography with metal artifact reduction software (MARS). Dual-energy computed tomography scans (fast kV-switching) are performed on a phantom, by varying the number of metal rods (Ti and Pb) and reference iodine materials. Objective and subjective image analyses are performed on retroreconstructed virtual monochromatic images (VMIs) (VMI at 70 keV). The maximum artifact indices for VMI-Ti and VMI-Pb (5 metal rods) with MARS (without MARS) were 17.4 (166.7) and 34.6 (810.6), respectively; MARS significantly improved the mean subjective 5-point score (P < 0.05). The maximum differences between the measured Hounsfield unit and theoretical values for 5 mg/mL iodine and 2-mm core rods were -42.2% and -68.5%, for VMI-Ti and VMI-Pb (5 metal rods), respectively, and the corresponding differences in the iodine concentration were -64.7% and -73.0%, respectively. Metal artifact reduction software improved the objective and subjective image quality; however, the quantitative values were underestimated.

Physical characterization of aerosol particles during the Chinese New Year’s firework events

NASA Astrophysics Data System (ADS)

Zhang, Min; Wang, Xuemei; Chen, Jianmin; Cheng, Tiantao; Wang, Tao; Yang, Xin; Gong, Youguo; Geng, Fuhai; Chen, Changhong

2010-12-01

Measurements for particles 10 nm to 10 μm were taken using a Wide-range Particle Spectrometer during the Chinese New Year (CNY) celebrations in 2009 in Shanghai, China. These celebrations provided an opportunity to study the number concentration and size distribution of particles in an especial atmospheric pollution situation due to firework displays. The firework activities had a clear contribution to the number concentration of small accumulation mode particles (100-500 nm) and PM 1 mass concentration, with a maximum total number concentration of 3.8 × 10 4 cm -3. A clear shift of particles from nucleation and Aitken mode to small accumulation mode was observed at the peak of the CNY firework event, which can be explained by reduced atmospheric lifetimes of smaller particles via the concept of the coagulation sink. High particle density (2.7 g cm -3) was identified as being particularly characteristic of the firework aerosols. Recalculated fine particles PM 1 exhibited on average above 150 μg m -3 for more than 12 hours, which was a health risk to susceptible individuals. Integral physical parameters of firework aerosols were calculated for understanding their physical properties and further model simulation.

Accuracy of the raw-data-based effective atomic numbers and monochromatic CT numbers for contrast medium with a dual-energy CT technique.

PubMed

Kawahara, Daisuke; Ozawa, Shuichi; Yokomachi, Kazushi; Tanaka, Sodai; Higaki, Toru; Fujioka, Chikako; Suzuki, Tatsuhiko; Tsuneda, Masato; Nakashima, Takeo; Ohno, Yoshimi; Nagata, Yasushi

2018-02-01

To evaluate the accuracy of raw-data-based effective atomic number (Z eff ) values and monochromatic CT numbers for contrast material of varying iodine concentrations, obtained using dual-energy CT. We used a tissue characterization phantom and varying concentrations of iodinated contrast medium. A comparison between the theoretical values of Z eff and that provided by the manufacturer was performed. The measured and theoretical monochromatic CT numbers at 40-130 keV were compared. The average difference between the Z eff values of lung (inhale) inserts in the tissue characterization phantom was 81.3% and the average Z eff difference was within 8.4%. The average difference between the Z eff values of the varying concentrations of iodinated contrast medium was within 11.2%. For the varying concentrations of iodinated contrast medium, the differences between the measured and theoretical monochromatic CT values increased with decreasing monochromatic energy. The Z eff and monochromatic CT numbers in the tissue characterization phantom were reasonably accurate. The accuracy of the raw-data-based Z eff values was higher than that of image-based Z eff values in the tissue-equivalent phantom. The accuracy of Z eff values in the contrast medium was in good agreement within the maximum SD found in the iodine concentration range of clinical dynamic CT imaging. Moreover, the optimum monochromatic energy for human tissue and iodinated contrast medium was found to be 70 keV. Advances in knowledge: The accuracy of the Z eff values and monochromatic CT numbers of the contrast medium created by raw-data-based, dual-energy CT could be sufficient in clinical conditions.

Diffusion of drag-reducing polymer solutions within a rough-walled turbulent boundary layer

NASA Astrophysics Data System (ADS)

Elbing, Brian R.; Dowling, David R.; Perlin, Marc; Ceccio, Steven L.

2010-04-01

The influence of surface roughness on diffusion of wall-injected, drag-reducing polymer solutions within a turbulent boundary layer was studied with a 0.94 m long flat-plate test model at speeds of up to 10.6 m s-1 and Reynolds numbers of up to 9×106. The surface was hydraulically smooth, transitionally rough, or fully rough. Mean concentration profiles were acquired with planar laser induced fluorescence, which was the primary flow diagnostic. Polymer concentration profiles with high injection concentrations (≥1000 wppm) had the peak concentration shifted away from the wall, which was partially attributed to a lifting phenomenon. The diffusion process was divided into three zones—initial, intermediate, and final. Studies of polymer injection into a polymer ocean at concentrations sufficient for maximum drag reduction indicated that the maximum initial zone length is of the order of 100 boundary layer thicknesses. The intermediate zone results indicate that friction velocity and roughness height are important scaling parameters in addition to flow and injection conditions. Lastly, the current results were combined with those in Petrie et al. ["Polymer drag reduction with surface roughness in flat-plate turbulent boundary layer flow," Exp. Fluids 35, 8 (2003)] to demonstrate that the influence of polymer degradation increases with increased surface roughness.

Analysis of variance to assess statistical significance of Laplacian estimation accuracy improvement due to novel variable inter-ring distances concentric ring electrodes.

PubMed

Makeyev, Oleksandr; Joe, Cody; Lee, Colin; Besio, Walter G

2017-07-01

Concentric ring electrodes have shown promise in non-invasive electrophysiological measurement demonstrating their superiority to conventional disc electrodes, in particular, in accuracy of Laplacian estimation. Recently, we have proposed novel variable inter-ring distances concentric ring electrodes. Analytic and finite element method modeling results for linearly increasing distances electrode configurations suggested they may decrease the truncation error resulting in more accurate Laplacian estimates compared to currently used constant inter-ring distances configurations. This study assesses statistical significance of Laplacian estimation accuracy improvement due to novel variable inter-ring distances concentric ring electrodes. Full factorial design of analysis of variance was used with one categorical and two numerical factors: the inter-ring distances, the electrode diameter, and the number of concentric rings in the electrode. The response variables were the Relative Error and the Maximum Error of Laplacian estimation computed using a finite element method model for each of the combinations of levels of three factors. Effects of the main factors and their interactions on Relative Error and Maximum Error were assessed and the obtained results suggest that all three factors have statistically significant effects in the model confirming the potential of using inter-ring distances as a means of improving accuracy of Laplacian estimation.

Sperm-egg penetration assay assessment of the contraceptive effects of glycerol and egg yolk in rooster sperm diluents.

PubMed

Abouelezz, F M K; Castaño, C; Toledano-Díaz, A; Esteso, M C; López-Sebastián, A; Campo, J L; Santiago-Moreno, J

2015-06-01

Glycerol (GLY) and egg yolk (EY) are good cryoprotectants of avian and mammalian sperm, but in birds, they strongly inhibit the eventual fertilization of ova. Using the sperm penetration (SP-holes) assay and fertility trials, the present study investigates (1) the possible mechanism by which this contraceptive effect occurs in chickens and (2) the maximum concentrations of GLY and EY tolerated by fresh rooster sperm. Seventy Black-Barred Andaluza hens (five per treatment) were inseminated four times (twice per week) with 0.1 mL of fresh semen from roosters of the same breed diluted 1:1 (v:v) with Lake and Ravie medium containing different concentrations of GLY or EY. No adverse effects on acrosome integrity, sperm motility, or viability were seen with any concentration of GLY or EY. The number of SP-holes on perivitelline layer samples taken from above the germinal disc became progressively lower at GLY concentrations of 1.5% or greater (P > 0.05). No holes caused by sperms were seen in unfertilized eggs. The corresponding fertility results showed similar reductions when the GLY concentration was 1.5% or greater. No changes in the number of SP-holes were seen with increasing EY concentrations (0%-7.5%), nor were any differences in fertility observed, except for a reduction when 15% EY was used. The results therefore reveal that GLY affects the transit of sperms through the oviduct in their attempt to reach the infundibulum area, limiting their access to the ovum perivitelline layer. Egg yolk had no such effect, nor did it influence acrosome reaction capacity; its mechanism of contraceptive action therefore remains unknown. The maximum GLY and EY concentrations tolerated by the rooster sperm were 0.75% and 7.5%, respectively. Copyright © 2015 Elsevier Inc. All rights reserved.

Hydroxyapatite coatings containing Zn and Si on Ti-6Al-4Valloy by plasma electrolytic oxidation

NASA Astrophysics Data System (ADS)

Hwang, In-Jo; Choe, Han-Cheol

2018-02-01

In this study, hydroxyapatite coatings containing Zn and Si on Ti-6Al-4Valloy by plasma electrolytic oxidation were researched using various experimental instruments. The pore size is depended on the electrolyte concentration and the particle size and number of pore increase on surface part and pore part. In the case of Zn/Si sample, pore size was larger than that of Zn samples. The maximum size of pores decreased and minimum size of pores increased up to 10Zn/Si and Zn and Si affect the formation of pore shapes. As Zn ion concentration increases, the size of the particle tends to increase, the number of particles on the surface part is reduced, whereas the size of the particles and the number of particles on pore part increased. Zn is mainly detected at pore part, and Si is mainly detected at surface part. The crystallite size of anatase increased as the Zn ion concentration, whereas, in the case of Si ion added, crystallite size of anatase decreased.

Quality of water from shallow wells in the rice-growing area in southwestern Louisiana, 1999 through 2001

USGS Publications Warehouse

Tollett, Roland W.; Fendick, Robert B.

2004-01-01

In 1999-2001, the U.S. Geological Survey installed and sampled 27 shallow wells in the rice-growing area in southwestern Louisiana as part of the Acadian-Pontchartrain Study Unit of the National Water-Quality Assessment Program. The purpose of this report is to describe the waulity of water from shallow wells in the rice-growing area and to relate that water quality to natural and anthropogenic activities, particularly rice agriculture. Ground-water samples were analyzed for general ground-water properties and about 150 water-quality constituents, including major inorganic ions, trace elements, nutrients, dissolved organic carbon (DOC), pesticides, radon, chloroflourocarbons, and selected stable isotopes. Dissolved solids concentrations for 17 wells exceeded the U.S. Environmental Protection Agency secondary minimum containment level of 500 milligrams per liter (mg/L) for drinking water. Concentrations for major pesticides generally were less than the maximum contaminant levels for drinking water. Two major inorganic ions, sulfate and chloride, and two trace elements, iron and manganese, had concentrations that were greater than the secondary maximum containment levels. Three nutrient concentrations were greater than 2 mg/L, a level that might indicate contamination from human activities, and one nutrient concentration (that for nitrite plus nitrite as nitrogen) was greater than the maximum contaminant level of 10 mg/L for drinking water. The median concentration for DOC was 0.5 mg/L, indicating naturally-occurring DOC conditions in the study area. Thirteen pesticides and 7 pesticide degradation products were detected in 14 of the 27 wells sampled. Bentazon, 2, 4-D, and molinate (three rice herbicides) were detected in water from four, one, and one wells, respectively, and malathion (a rice insecticide) was deteced in water fromone well. Low-level concentrations and few detections of nutrients and pesticides indicated that ground-water quality was affected slightly by anthropogenic activities. Quality-control samples, including field blanks, replicates, and spikes, indicated no bias in ground-water data from collection on analysis. Radon concentrations for 22 of the 24 wells sampled wer at or greater than the U.S. Environmental Protection Agency proposed maximum contaminant level of 300 picocuries per liter. Chlorofluorocarbon concentrations in selected wells indicated the apparent ages of the ground water varied with depth water level and ranged from about 17 to 49 years. The stable isotopes of hydrogen and oxygen in water molecules indicated the origin of ground water in the study area was rainwater that originated near the study area and that few geochemical or physical processes influenced the stable isotopic composition of the shallow ground water. The Spearman rank correlation was used to detemrine whther significant correlations existed between physical properties, selected chemical constituents, the number of pesticides detected, and the apparent age of water. The depth to ground water was positively correlated to the well depth and inversely correlated to dissolved solids and other constituents, such as radon, indicating the ground water was under unconfined or semiconfined conditions and more dilute with increasing depth. As the depth to ground water increased, the concentrations of dissolved solids and other constituents decreased, possibly because the deeper sands had a greater transmittal of ground water, which, over time, would flush out, or dilute, the concentrations of dissolved solids in the natural sediments. The apparent age of water was correlated inversely with nitrite plus nitrite concentration, indicating that as apparent age increased, the nitrite plus nitrite concentration decreased. No significant correlations existed between the number of pesticides detected and any of the physical or chemica

A review of odour impact criteria in selected countries around the world.

PubMed

Brancher, Marlon; Griffiths, K David; Franco, Davide; de Melo Lisboa, Henrique

2017-02-01

Exposure to environmental odour can result in annoyance, health effects and depreciation of property values. Therefore, many jurisdictions classify odour as an atmospheric pollutant and regulate emissions and/or impacts from odour generating activities at a national, state or municipal level. In this work, a critical review of odour regulations in selected jurisdictions of 28 countries is presented. Individual approaches were identified as: comparing ambient air odour concentration and individual chemicals statistics against impact criteria (maximum impact standard); using fixed and variable separation distances (separation distance standard); maximum emission rate for mixtures of odorants and individual chemical species (maximum emission standard); number of complaints received or annoyance level determined via community surveys (maximum annoyance standard); and requiring use of best available technologies (BAT) to minimize odour emissions (technology standard). The comparison of model-predicted odour concentration statistics against odour impact criteria (OIC) is identified as one of the most common tools used by regulators to evaluate the risk of odour impacts in planning stage assessments and is also used to inform assessment of odour impacts of existing facilities. Special emphasis is given to summarizing OIC (concentration percentile and threshold) and the manner in which they are applied. The way short term odour peak to model time-step mean (peak-to-mean) effects is also captured. Furthermore, the fundamentals of odorant properties, dimensions of nuisance odour, odour sampling and analysis methods and dispersion modelling guidance are provided. Common elements of mature and effective odour regulation frameworks are identified and an integrated multi-tool strategy is recommended. Copyright © 2016 Elsevier Ltd. All rights reserved.

Exhaust emission survey of an F100 afterburning turbofan engine at simulated altitude flight conditions

NASA Technical Reports Server (NTRS)

Moss, J. E.; Cullom, R. R.

1981-01-01

Emissions of carbon monoxide, total oxides of nitrogen, unburned hydrocarbons, and carbon dioxide from an F100, afterburning, two spool turbofan engine at simulated flight conditions are reported. For each flight condition emission measurements were made for two or three power levels from intermediate power (nonafterburning) through maximum afterburning. The data showed that emissions vary with flight speed, altitude, power level, and radial position across the nozzle. Carbon monoxide emissions were low for intermediate power (nonafterburning) and partial afterburning, but regions of high carbon monoxide were present downstream of the flame holder at maximum afterburning. Unburned hydrocarbon emissions were low for most of the simulated flight conditions. The local NOX concentrations and their variability with power level increased with increasing flight Mach number at constant altitude, and decreased with increasing altitude at constant Mach number. Carbon dioxide emissions were proportional to local fuel air ratio for all conditions.

Numerical study of a confined slot impinging jet with nanofluids

PubMed Central

2011-01-01

Background Heat transfer enhancement technology concerns with the aim of developing more efficient systems to satisfy the increasing demands of many applications in the fields of automotive, aerospace, electronic and process industry. A solution for obtaining efficient cooling systems is represented by the use of confined or unconfined impinging jets. Moreover, the possibility of increasing the thermal performances of the working fluids can be taken into account, and the introduction of nanoparticles in a base fluid can be considered. Results In this article, a numerical investigation on confined impinging slot jet working with a mixture of water and Al2O3 nanoparticles is described. The flow is turbulent and a constant temperature is applied on the impinging. A single-phase model approach has been adopted. Different geometric ratios, particle volume concentrations and Reynolds number have been considered to study the behavior of the system in terms of average and local Nusselt number, convective heat transfer coefficient and required pumping power profiles, temperature fields and stream function contours. Conclusions The dimensionless stream function contours show that the intensity and size of the vortex structures depend on the confining effects, given by H/W ratio, Reynolds number and particle concentrations. Furthermore, for increasing concentrations, nanofluids realize increasing fluid bulk temperature, as a result of the elevated thermal conductivity of mixtures. The local Nusselt number profiles show the highest values at the stagnation point, and the lowest at the end of the heated plate. The average Nusselt number increases for increasing particle concentrations and Reynolds numbers; moreover, the highest values are observed for H/W = 10, and a maximum increase of 18% is detected at a concentration equal to 6%. The required pumping power as well as Reynolds number increases and particle concentrations grow, which is almost 4.8 times greater than the values calculated in the case of base fluid. List of symbols PMID:21711743

Scale inhibition in geothermal operations: experiments with Dequest 2060 phosphonate in Republic's East Mesa Field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vetter, O.J.; Campbell, D.A.

Two calcium carbonate (CaCO/sub 3/) scale inhibition tests have been performed at East Mesa wells number 16-29 and number 56-30. The first test at well number 16-29 could not be finished due to downhole pump problems. However, two inhibitor concentration runs were completed and a third run started before the pump failed. A follow-up test at well number 56-30 was completed according to the original plan. Typical power plant conditions (i.e., pressure and temperature drops, flow conditions) were simulated by using test loops (pipe diameters of eight inches at well number 16-29 and twelve inches at well number 56-30) andmore » field separators. Untreated East Mesa brine exhibits a calcium carbonate scale tendency as soon as the pressure is dropped below 75 psig. The uninhibited brine from well number 16-29 formed a maximum scale thickness of 0.5 inch in an eight inch ID pipe after a 92.75 hour test run at an average production rate of 375,000 lb/hr. The brine from well number 56-30 formed a maximum scale thickness of 1.25 inches in a twelve inch ID pipe after a 104 hour test run at an average production rate of 722,000 lb/hr. The principal conclusions of this test work are listed.« less

Exploiting the Phenomenon of Liquid-Liquid Phase Separation for Enhanced and Sustained Membrane Transport of a Poorly Water-Soluble Drug.

PubMed

Indulkar, Anura S; Gao, Yi; Raina, Shweta A; Zhang, Geoff G Z; Taylor, Lynne S

2016-06-06

Recent studies on aqueous supersaturated lipophilic drug solutions prepared by methods including antisolvent addition, pH swing, or dissolution of amorphous solid dispersions (ASDs) have demonstrated that when crystallization is slow, these systems undergo liquid-liquid phase separation (LLPS) when the concentration of the drug in the medium exceeds its amorphous solubility. Following LLPS, a metastable equilibrium is formed where the concentration of drug in the continuous phase corresponds to the amorphous solubility while the dispersed phase is composed of a nanosized drug-rich phase. It has been reasoned that the drug-rich phase may act as a reservoir, enabling the rate of passive transport of the drug across a membrane to be maintained at the maximum value for an extended period of time. Herein, using clotrimazole as a model drug, and a flow-through diffusion cell, the reservoir effect is demonstrated. Supersaturated clotrimazole solutions at concentrations below the amorphous solubility show a linear relationship between the maximum flux and the initial concentration. Once the concentration exceeds the amorphous solubility, the maximum flux achieved reaches a plateau. However, the duration for which the high flux persists was found to be highly dependent on the number of drug-rich nanodroplets present in the donor compartment. Macroscopic amorphous particles of clotrimazole did not lead to the same reservoir effect observed with the nanodroplets formed through the process of LLPS. A first-principles mathematical model was developed which was able to fit the experimental receiver concentration-time profiles for concentration regimes both below and above amorphous solubility, providing support for the contention that the nanodroplet phase does not directly diffuse across the membrane but, instead, rapidly replenishes the drug in the aqueous phase that has been removed by transport across the membrane. This study provides important insight into the properties of supersaturated solutions and how these might in turn impact oral absorption through effects on passive membrane transport rates.

Ultrafine particles, and PM 2.5 generated from cooking in homes

NASA Astrophysics Data System (ADS)

Wan, Man-Pun; Wu, Chi-Li; Sze To, Gin-Nam; Chan, Tsz-Chun; Chao, Christopher Y. H.

2011-11-01

Exposure to airborne particulate matters (PM) emitted during cooking can lead to adverse health effects. An understanding of the exposure to PM during cooking at home provides a foundation for the quantification of possible health risks. The concentrations of airborne particles covering the ultrafine (14.6-100 nm) and accumulation mode (100-661.2 nm) size ranges and PM 2.5 (airborne particulate matters smaller than 2.5 μm in diameter) during and after cooking activities were measured in 12 naturally ventilated, non-smoking homes in Hong Kong, covering a total of 33 cooking episodes. The monitored homes all practiced Chinese-style cooking. Cooking elevated the average number concentrations of ultrafine particles (UFPs) and accumulation mode particles (AMPs) by 10 fold from the background level in the living room and by 20-40 fold in the kitchen. PM 2.5 mass concentrations went up to the maximum average of about 160 μg m -3 in the kitchen and about 60 μg m -3 in the living room. Cooking emitted particles dispersed quickly from the kitchen to the living room indicating that the health impact is not limited to occupants in the kitchen. Particle number and mass concentrations remained elevated for 90 min in the kitchen and for 60 min in the living room after cooking. Particles in cooking emissions were mainly in the ultrafine size range in terms of the number count while AMPs contributed to at least 60% of the surface area concentrations in the kitchen and 73% in the living room. This suggests that AMPs could still be a major health concern since the particle surface area concentration is suggested to have a more direct relationship with inhalation toxicity than with number concentration. Particle number concentration (14.6-661.2 nm) in the living room was about 2.7 times that in the outdoor environment, suggesting that better ventilation could help reduce exposure.

Growth and lasing of single crystal YAG fibers with different Ho3+ concentrations

NASA Astrophysics Data System (ADS)

Bera, Subhabrata; Nie, Craig D.; Soskind, Michael G.; Li, Yuan; Harrington, James A.; Johnson, Eric G.

2018-01-01

A method to grow single crystal (SC) yttrium aluminum garnet (YAG) fibers with varied rare-earth ion dopant concentration has been proposed. Crystalline holmium aluminum garnet (HoAG), prepared via sol-gel process, was dip-coated on to previously grown SC YAG fibers. The HoAG coated SC YAG fiber preforms were re-grown to a smaller diameter using the laser heated pedestal growth (LHPG) technique. The final dopant concentration of the re-grown SC fiber was varied by changing the number of HoAG coatings on the preform. 120 μm diameter SC Ho:YAG fibers with four different dopant concentrations were grown. Lasing was demonstrated at 2.09 μm for these fibers. A maximum of 58.5% optical-to-optical slope efficiency was obtained.

Escherichia coli Concentrations in the Mill Creek Watershed, Cleveland, Ohio, 2001-2004

USGS Publications Warehouse

Brady, Amie M.G.

2007-01-01

Mill Creek in Cleveland, Ohio, receives discharges from combined-sewer overflows (CSOs) and other sanitary-sewage inputs. These discharges affect the water quality of the creek and that of its receiving stream, the Cuyahoga River. In an effort to mitigate this problem, the Northeast Ohio Regional Sewer District implemented a project to eliminate or control (by reducing the number of overflows) all of the CSOs in the Mill Creek watershed. This study focused on monitoring the microbiological water quality of the creek before and during sewage-collection system modifications. Routine samples were collected semimonthly from August 2001 through September 2004 at a site near a U.S. Geological Survey stream gage near the mouth of Mill Creek. In addition, event samples were collected September 19 and 22, 2003, when rainfall accumulations were 0.5 inches (in.) or greater. Concentrations of Escherichia coli (E. coli) were determined and instantaneous discharges were calculated. Streamflow and water-quality characteristics were measured at the time of sampling, and precipitation data measured at a nearby precipitation gage were obtained from the National Oceanic and Atmospheric Administration. Concentrations of E. coli were greater than Ohio's single-sample maximum for primary-contact recreation (298 colony-forming units per 100 milliliters (CFU/100 mL)) in 84 percent of the routine samples collected. In all but one routine sample E. coli concentrations in samples collected when instantaneous streamflows were greater than 20 cubic feet per second (ft3/s) were greater than Ohio's single-sample maximum. When precipitation occurred in the 24-hour period before routine sample collection, concentrations were greater than the maximum in 89 percent of the samples as compared to 73 percent when rainfall was absent during the 24 hours prior to routine sample collection. Before modifications to the sewage-collection system in the watershed began, E. coli concentrations in Mill Creek ranged from 220 to 29,000 CFU/100 mL. After major modifications, E. coli concentrations ranged from 110 to 80,000 CFU/100 mL. The percentage of sample E. coli concentrations in the former group greater than Ohio's single-sample maximum was 88 percent, whereas 85 percent of sample concentrations was greater than the maximum after major modifications occurred. Instantaneous discharges of E. coli were calculated for each of the modification periods. No statistically significant difference was observed between the median instantaneous discharges of E. coli for the premodification and minor-modification periods (5.1 ? 106 and 3.6 ? 106 CFU per second, respectively). During rainfall events in September 2003, samples were collected every 15 to 30 minutes. E. coli concentrations in all of these samples (n = 34) were greater than Ohio's single-sample maximum for primary-contact recreation. On September 19, total accumulated rainfall was 1.7 in., and streamflow reached a peak of 1,040 ft3/s. Sample collection started after 0.8 in. of precipitation had fallen and continued throughout the remainder of the storm. For these samples, E. coli concentrations ranged from 32,000 to 140,000 CFU/100 mL. On September 22, total accumulated rainfall was 0.5 in., and streamflow reached a peak of 497 ft3/s. Sample collection began before the start of the rain and continued throughout the storm. E. coli concentrations ranged from 450 to 260,000 CFU/100 mL.

Impact dynamics of oxidized liquid metal drops

NASA Astrophysics Data System (ADS)

Xu, Qin; Brown, Eric; Jaeger, Heinrich M.

2013-04-01

With exposure to air, many liquid metals spontaneously generate an oxide layer on their surface. In oscillatory rheological tests, this skin is found to introduce a yield stress that typically dominates the elastic response but can be tuned by exposing the metal to hydrochloric acid solutions of different concentration. We systematically studied the normal impact of eutectic gallium-indium (eGaIn) drops under different oxidation conditions and show how this leads to two different dynamical regimes. At low impact velocity (or low Weber number), eGaIn droplets display strong recoil and rebound from the impacted surface when the oxide layer is removed. In addition, the degree of drop deformation or spreading during impact is controlled by the oxide skin. We show that the scaling law known from ordinary liquids for the maximum spreading radius as a function of impact velocity can still be applied to the case of oxidized eGaIn if an effective Weber number We is employed that uses an effective surface tension factoring in the yield stress. In contrast, no influence on spreading from different oxidations conditions is observed for high impact velocity. This suggests that the initial kinetic energy is mostly damped by bulk viscous dissipation. Results from both regimes can be collapsed in an impact phase diagram controlled by two variables, the maximum spreading factor Pm=R0/Rm, given by the ratio of initial to maximum drop radius, and the impact number K=We/Re4/5, which scales with the effective Weber number We as well as the Reynolds number Re. The data exhibit a transition from capillary to viscous behavior at a critical impact number Kc≈0.1.

Impact dynamics of oxidized liquid metal drops.

PubMed

Xu, Qin; Brown, Eric; Jaeger, Heinrich M

2013-04-01

With exposure to air, many liquid metals spontaneously generate an oxide layer on their surface. In oscillatory rheological tests, this skin is found to introduce a yield stress that typically dominates the elastic response but can be tuned by exposing the metal to hydrochloric acid solutions of different concentration. We systematically studied the normal impact of eutectic gallium-indium (eGaIn) drops under different oxidation conditions and show how this leads to two different dynamical regimes. At low impact velocity (or low Weber number), eGaIn droplets display strong recoil and rebound from the impacted surface when the oxide layer is removed. In addition, the degree of drop deformation or spreading during impact is controlled by the oxide skin. We show that the scaling law known from ordinary liquids for the maximum spreading radius as a function of impact velocity can still be applied to the case of oxidized eGaIn if an effective Weber number We* is employed that uses an effective surface tension factoring in the yield stress. In contrast, no influence on spreading from different oxidations conditions is observed for high impact velocity. This suggests that the initial kinetic energy is mostly damped by bulk viscous dissipation. Results from both regimes can be collapsed in an impact phase diagram controlled by two variables, the maximum spreading factor P(m)=R(0)/R(m), given by the ratio of initial to maximum drop radius, and the impact number K=We*/Re(4/5), which scales with the effective Weber number We* as well as the Reynolds number Re. The data exhibit a transition from capillary to viscous behavior at a critical impact number K(c)≈0.1.

A study of the sea-salt chemistry using size-segregated aerosol measurements at coastal Antarctic station Neumayer

NASA Astrophysics Data System (ADS)

Teinilä, K.; Frey, A.; Hillamo, R.; Tülp, H. C.; Weller, R.

2014-10-01

Aerosol chemical and physical properties were measured in 2010 at Neumayer research station, Antarctica. Samples for chemical analysis (ion chromatography) were collected using a Teflon/Nylon filter combination (TNy) sampler, and with a multi stage low pressure impactor (SDI). Particle number concentration was measured continuously with a Grimm OPC optical particle counter. Total particle number concentration varied largely throughout the year, and the highest number concentrations for particles larger than 0.3 μm were observed simultaneously with the highest sea salt concentrations. About 50% of the sea salt aerosol mass was found in the submicron size range. Below 0.2 μm of particle aerodynamic diameter the contribution of sea salt aerosols was negligible. Further analysis showed that sea salt aerosols had undergone physico-chemical processes, either during the transportation, or during their formation. High degree of chloride depletion was observed during austral summer, when the presence of acidic gases exhibit their characteristic seasonal maximum. Apart from chloride depletion, excess chloride relating to sodium was also detected in one SDI sample, indicating actually a sodium depletion by mirabilite formation on freshly formed sea ice areas. Analysis of selected episodes showed that the concentration of sea salt particles, their modal structure, and their chemical composition is connected with their source areas, their formation mechanisms, and local transport history.

Application of chitosan and chitosan nanoparticles for the control of Fusarium head blight of wheat (Fusarium graminearum) in vitro and greenhouse.

PubMed

Kheiri, A; Moosawi Jorf, S A; Malihipour, A; Saremi, H; Nikkhah, M

2016-12-01

Fusarium head blight (FHB) disease caused by Fusarium graminearum is one of the most important diseases of wheat in humid and warm areas. This disease significantly reduces yield as well as seed quality. The aim of this work was to evaluate the possibility of control of FHB by chitosan (CS) and chitosan nanoparticles (CS/NPs). In vitro, the application of various concentrations of CS and CS/NPs showed significant inhibition of both radial mycelial growth and number of colonies formed against F. graminearum. The application of 1000 and 5000ppm concentration of CS and CS/NPs produced maximum inhibition of radial mycelial growth in comparison to the control, respectively. The microscopic examination, of treated F. graminearum with the CS and CS/NPs, showed dehydration and deformation in mycelial growth and some hyphae were collapsed. The maximum percentage reduction number of colonies was observed in 5000ppm concentration of both CS and CS/NPs. To test the effect of CS and CS/NPs on spore germination, four concentrations were used for 4 and 24h incubation. The 24h incubation of F. graminearum spores with a 5000ppm solution of CS greatly reduced the number of germinating spores. In greenhouse trials, the disease severity percentage was low when CS and CS/NPs were applied before fungus inoculation on the plants and 1000ppm concentration. The spores of F. graminearum germinated on the anther, hyphae penetrated into anther and colonized the palea, lemma and glume after 24 and 72 hpi, respectively. Wherease, the spikelets treated with CS and CS/NPs were infected slowly. Light microscopy and TEM observations indicated that mycelium penetrated into the cells through stoma and transited to other cells by cell wall or plasmodesmata. Mycelial growth caused conidia into cells but CS and CS/NPs prevented of it's growth. Results showed that CS and CS/NPs could be a useful biological pesticide for controlling FHB. Copyright © 2016 Elsevier B.V. All rights reserved.

Effectiveness of bio-slurry on the growth and production of soybean (Glycine max (L.) Merrill)

NASA Astrophysics Data System (ADS)

Rafiuddin; Mollah, A.; Iswoyo, H.

2018-05-01

This research was aimed to determine the effectiveness of bio-slurry fertilizer on the growth and production of soybean plants which was conducted in the Pucak village, Tompobulu District, Maros Regency, South Sulawesi from July to October 2016. The research was set in randomized block design (RBD) with 8 treatments replicated three times. Treatment used were the application of bio-slurry consisted of 8 level of concentrations, namely: control (0 mL.liter-1 of water), 3, 5, 7, 9, 11, 13 and 15 mL.liter-1 of water. The variables measured were plant’s height, number of pods, weight of 100-seed, and soybean seeds’ yield per hectare. The results of research shows that the application of bio-slurry effectively improved growth and yield of soybean (pod’s number, 100-seed’s weight and seed yield per hectare). Optimal concentration of liquid bio-slurry to obtain maximum results were 9.27 mL.liter-1 of water for the highest number of pods (68.49 pods); concentration of 8.75 mL.liter-1 of water for heaviest weight of 100 grains (14.22 grams); and the concentration 8,12 mL.liter-1 of water for the highest production of seed per hectare (23.20 quintal).

36 CFR 20.3 - Maximum number of permittees.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 1 2011-07-01 2011-07-01 false Maximum number of permittees... INTERIOR ISLE ROYALE NATIONAL PARK; COMMERCIAL FISHING § 20.3 Maximum number of permittees. Commercial fishermen to whom the annual revocable permits may be granted shall not exceed the maximum number of persons...

USSR and Eastern Europe Scientific Abstracts, Biomedical and Behavioral Sciences, Number 86

DTIC Science & Technology

1978-02-03

Biochemistry 6 Epidemiology 15 Hydrobiology • • IT Immunology .. • 1° Industrial Microbiology 21 Industrial Toxicology 22 Marine Mammals 28...included measures to decrease the con- tamination of feeds and animal husbandry products with pesticides; improve- ment of methods and the organization...permissible levels of pesticide residues in agricultural products and the maximum permissible concentrations of pesticides for work- ers working with them

40 CFR Table 2 to Subpart Dddd of... - Operating Requirements

Code of Federal Regulations, 2012 CFR

2012-07-01

... THC concentration a in the thermal oxidizer exhaust below the maximum concentration established during... average THC concentration a in the catalytic oxidizer exhaust below the maximum concentration established... the range established according to § 63.2262(m) Maintain the 24-hour block average THC concentration a...

40 CFR Table 2 to Subpart Dddd of... - Operating Requirements

Code of Federal Regulations, 2013 CFR

2013-07-01

... THC concentration a in the thermal oxidizer exhaust below the maximum concentration established during... average THC concentration a in the catalytic oxidizer exhaust below the maximum concentration established... the range established according to § 63.2262(m) Maintain the 24-hour block average THC concentration a...

40 CFR Table 2 to Subpart Dddd of... - Operating Requirements

Code of Federal Regulations, 2014 CFR

2014-07-01

... THC concentration a in the thermal oxidizer exhaust below the maximum concentration established during... average THC concentration a in the catalytic oxidizer exhaust below the maximum concentration established... the range established according to § 63.2262(m) Maintain the 24-hour block average THC concentration a...

Retrieval of sodium number density profiles in the mesosphere and lower thermosphere from SCIAMACHY limb emission measurements

NASA Astrophysics Data System (ADS)

Langowski, M. P.; von Savigny, C.; Burrows, J. P.; Rozanov, V. V.; Dunker, T.; Hoppe, U.-P.; Sinnhuber, M.; Aikin, A. C.

2016-01-01

An algorithm has been developed for the retrieval of sodium atom (Na) number density on a latitude and altitude grid from SCIAMACHY (SCanning Imaging Absorption spectroMeter for Atmospheric CHartographY) limb measurements of the Na resonance fluorescence. The results are obtained between 50 and 150 km altitude and the resulting global seasonal variations of Na are analyzed. The retrieval approach is adapted from that used for the retrieval of magnesium atom (Mg) and magnesium ion (Mg+) number density profiles recently reported by Langowski et al. (2014). Monthly mean values of Na are presented as a function of altitude and latitude. This data set was retrieved from the 4 years of spectroscopic limb data of the SCIAMACHY mesosphere and lower thermosphere (MLT) measurement mode (mid-2008 to early 2012). The Na layer has a nearly constant peak altitude of 90-93 km for all latitudes and seasons, and has a full width at half maximum of 5-15 km. Small but significant seasonal variations in Na are identified for latitudes less than 40°, where the maximum Na number densities are 3000-4000 atoms cm-3. At middle to high latitudes a clear seasonal variation with a winter maximum of up to 6000 atoms cm-3 is observed. The high latitudes, which are only measured in the summer hemisphere, have lower number densities, with peak densities being approximately 1000 Na atoms cm-3. The full width at half maximum of the peak varies strongly at high latitudes and is 5 km near the polar summer mesopause, while it exceeds 10 km at lower latitudes. In summer the Na atom concentration at high latitudes and at altitudes below 88 km is significantly smaller than that at middle latitudes. The results are compared with other observations and models and there is overall a good agreement with these.

The dynamics of suspended particulate matter (SPM) and chlorophyll-a from intratidal to annual time scales in a coastal turbidity maximum

NASA Astrophysics Data System (ADS)

van der Hout, C. M.; Witbaard, R.; Bergman, M. J. N.; Duineveld, G. C. A.; Rozemeijer, M. J. C.; Gerkema, T.

2017-09-01

The analysis of 1.8 years of data gives an understanding of the response to varying forcing of suspended particulate matter (SPM) and chlorophyll-a (CHL-a) in a coastal turbidity maximum zone (TMZ). Both temporal and vertical concentration variations in the near-bed layer (0-2 m) in the shallow (11 m deep) coastal zone at 1 km off the Dutch coast are shown. Temporal variations in the concentration of both parameters are found on tidal and seasonal scales, and a marked response to episodic events (e.g. storms). The seasonal cycle in the near-bed CHL-a concentration is determined by the spring bloom. The role of the wave climate as the primary forcing in the SPM seasonal cycle is discussed. The tidal current provides a background signal, generated predominantly by local resuspension and settling and a minor role is for advection in the cross-shore and the alongshore direction. We tested the logarithmic Rouse profile to the vertical profiles of both the SPM and the CHL-a data, with respectively 84% and only 2% success. The resulting large percentage of low Rouse numbers for the SPM profiles suggest a mixed suspension is dominant in the TMZ, i.e. surface SPM concentrations are in the same order of magnitude as near-bed concentrations.

Impaired reproduction and individual growth of the water flea Daphnia magna as consequence of exposure to the non-ester pyrethroid etofenprox.

PubMed

Sancho, Encarna; Banegas, Sandra; Villarroel, María José; Ferrando, Dolores

2018-03-01

The effect of the pesticide etofenprox (0.76, 0.95, 1.18, 1.48, and 1.85 μg L -1 ) on survival, reproduction, and growth of Daphnia magna organisms was monitored using 21-day exposure tests. In order to test pesticide effects on D. magna, survival, length, mean total neonates per female, mean brood size, time to first reproduction, mean number broods per female, cumulative molting, and the population parameter intrinsic rate of natural increase (r) were used. Reproduction was seriously affected by etofenprox. Concentrations of etofenprox higher than 1.18 μg L -1 affected all the reproductive parameters analyzed as well as individual length. However, daphnids' survival after 21 days of pesticide exposure did not exhibited differences among experimental and control groups. The no observed effect concentration (NOEC), the lowest observed effect concentration (LOEC), and the maximum acceptable toxicant concentration (MATC) were calculated for the different parameters. A MATC estimation of 1.32 μg L -1 was calculated for mean brood size, mean number of broods per female, mean number of neonates per female, and the intrinsic rate of growth population. Etofenprox effect on the algae Nannochloris oculata was also evaluated. The selected etofenprox concentrations did not affect algal growth rate (μ) after 24 h; however, N. oculata exposed during 48 and 72 h to the highest etofenprox concentration showed a decreased in its population rate.

The effect of isoenzyme-selective PDE inhibitors on methacholine-induced contraction of guinea-pig and rat ileum.

PubMed Central

Tomkinson, A.; Raeburn, D.

1996-01-01

1. We have examined the effects of the isoenzyme-selective phosphodiesterase (PDE) inhibitors, vinpocetine (type 1), siguazodan (type 3), rolipram (type 4) and zaprinast (type 5) and the non-selective PDE inhibitor enprofylline on methacholine (MCh) contractile concentration-response curves on guinea-pig and rat isolated ileum. 2. In guinea-pig ileum, vinpocetine (10-300 microM), zaprinast (1-300 microM) and enprofylline (100-1000 microM) produced a concentration-dependent depression of the maximum response (Emax) to MCh only without effect on the MCh EC50 values (rank order of potency: zaprinast > vinpocetine > enprofylline). In contrast, siguazodan (10-300 microM) and rolipram (10-300 microM) produced a rightward displacement of the MCh concentration-response curve (increase in EC50: rank order; rolipram > siguazodan), with effects on the MCh maximum seen only at higher concentrations. 3. In the rat ileum, vinpocetine (10-300 microM), zaprinast (0.1-300 microM) and enprofylline (100-1000 microM) caused depression of the MCh maximum contraction (rank order: zaprinast > vinpocetine > enprofylline). Low concentrations of rolipram and siguazodan had no significant effect on the MCh maximum. In the presence of higher concentrations (> 100 microM) of rolipram and siguazodan, a maximum response was not achieved at the highest concentration of MCh tested. As in the guinea-pig ileum, only rolipram (10-300 microM) and siguazodan (10-300 microM) produced a significant, concentration-dependent, rightward displacement of the MCh concentration-response curve (increase in EC50: rank order: rolipram > siguazodan). 4. In the guinea-pig ileum, isoprenaline (0.1 microM) produced a rightward displacement (approximately 3 fold) of the MCh concentration-response curve, accompanied by a significant depression of the maximum response. Increasing the isoprenaline concentration (1 microM) had no further effect on either parameter. Sodium nitroprusside (SNP, > or = 10 microM) produced a concentration-dependent depression of the MCh maximum without an effect on the EC50. 5. In the rat ileum, isoprenaline (1 microM) produced a concentration-dependent rightward displacement (approximately 2.8 fold) of the MCh concentration-response curve with depression of the MCh maximum at higher (> or = 100 microM) concentrations. SNP produced depression of the MCh maximum at a concentration of 10 microM and above. Effects on the MCh EC50 were seen only at 100 and 300 microM. 6. In guinea-pig ileum, isoprenaline (0.1 microM) in combination with rolipram (10 microM) further increased the MCh EC50 and reduced the MCh maximum. The combination of SNP (10 microM) with zaprinast (0.1 microM) produced no further significant effect than SNP alone. 7. In rat ileum, isoprenaline (1 microM) in combination with rolipram (10 microM) further increased the EC50 and reduced the maximum. SNP (10 microM) had no significant effect on either the MCh maximum or EC50. A combination with zaprinast (1 microM) had no further effect. 8. In conclusion, all the PDE inhibitors tested produced a concentration-dependent inhibition of the MCh concentration-response curve, indicating a modulator role for the PDE isoenzymes in gastrointestinal smooth muscle contractility. The PDE inhibitors that elevate cyclic GMP produced a depression of the MCh maximum response only, whilst those that elevate cyclic AMP produced a rightward displacement of the MCh concentration-response curve. This was confirmed by the use of isoprenaline and SNP. This difference in the type of inhibition produced by these PDE isoenzyme inhibitors may reflect a different intracellular site/mechanism by which the cyclic AMP- and cyclic GMP-activated kinases act functionally to antagonize the contractile response. PMID:8864552

Ice particle production in mid-level stratiform mixed-phase clouds observed with collocated A-Train measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Damao; Wang, Zhien; Kollias, Pavlos

In this study, collocated A-Train CloudSat radar and CALIPSO lidar measurements between 2006 and 2010 are analyzed to study primary ice particle production characteristics in mid-level stratiform mixed-phase clouds on a global scale. For similar clouds in terms of cloud top temperature and liquid water path, Northern Hemisphere latitude bands have layer-maximum radar reflectivity (ZL) that is ~1 to 8 dBZ larger than their counterparts in the Southern Hemisphere. The systematically larger ZL under similar cloud conditions suggests larger ice number concentrations in mid-level stratiform mixed-phase clouds over the Northern Hemisphere, which is possibly related to higher background aerosol loadings.more » Furthermore, we show that springtime northern mid- and high latitudes have ZL that is larger by up to 6 dBZ (a factor of 4 higher ice number concentration) than other seasons, which might be related to more dust events that provide effective ice nucleating particles. Our study suggests that aerosol-dependent ice number concentration parameterizations are required in climate models to improve mixed-phase cloud simulations, especially over the Northern Hemisphere.« less

Ice particle production in mid-level stratiform mixed-phase clouds observed with collocated A-Train measurements

DOE PAGES

Zhang, Damao; Wang, Zhien; Kollias, Pavlos; ...

2018-03-28

In this study, collocated A-Train CloudSat radar and CALIPSO lidar measurements between 2006 and 2010 are analyzed to study primary ice particle production characteristics in mid-level stratiform mixed-phase clouds on a global scale. For similar clouds in terms of cloud top temperature and liquid water path, Northern Hemisphere latitude bands have layer-maximum radar reflectivity (ZL) that is ~1 to 8 dBZ larger than their counterparts in the Southern Hemisphere. The systematically larger ZL under similar cloud conditions suggests larger ice number concentrations in mid-level stratiform mixed-phase clouds over the Northern Hemisphere, which is possibly related to higher background aerosol loadings.more » Furthermore, we show that springtime northern mid- and high latitudes have ZL that is larger by up to 6 dBZ (a factor of 4 higher ice number concentration) than other seasons, which might be related to more dust events that provide effective ice nucleating particles. Our study suggests that aerosol-dependent ice number concentration parameterizations are required in climate models to improve mixed-phase cloud simulations, especially over the Northern Hemisphere.« less

40 CFR 75.72 - Determination of NOX mass emissions for common stack and multiple stack configurations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the affected units as the difference between NOX mass emissions measured in the common stack and NOX... emissions using the maximum potential NOX emission rate, the maximum potential flow rate, and either the maximum potential CO2 concentration or the minimum potential O2 concentration (as applicable). The maximum...

Airborne observations of cloud condensation nuclei spectra and aerosols over East Inner Mongolia

NASA Astrophysics Data System (ADS)

Yang, Jiefan; Lei, Hengchi; Lü, Yuhuan

2017-08-01

A set of vertical profiles of aerosol number concentrations, size distributions and cloud condensation nuclei (CCN) spectra was observed using a passive cloud and aerosol spectrometer (PCASP) and cloud condensation nuclei counter, over the Tongliao area, East Inner Mongolia, China. The results showed that the average aerosol number concentration in this region was much lower than that in heavily polluted areas. Monthly average aerosol number concentrations within the boundary layer reached a maximum in May and a minimum in September, and the variations in CCN number concentrations at different supersaturations showed the same trend. The parameters c and k of the empirical function N = cS k were 539 and 1.477 under clean conditions, and their counterparts under polluted conditions were 1615 and 1.42. Measurements from the airborne probe mounted on a Yun-12 (Y12) aircraft, together with Hybrid Single-Particle Lagrangian Integrated Trajectory model backward trajectories indicated that the air mass from the south of Tongliao contained a high concentration of aerosol particles (1000-2500 cm-3) in the middle and lower parts of the troposphere. Moreover, detailed intercomparison of data obtained on two days in 2010 indicated that the activation efficiency in terms of the ratio of N CCN to N a (aerosols measured from PCASP) was 0.74 (0.4 supersaturations) when the air mass mainly came from south of Tongliao, and this value increased to 0.83 on the relatively cleaner day. Thus, long-range transport of anthropogenic pollutants from heavily polluted mega cities, such as Beijing and Tianjin, may result in slightly decreasing activation efficiencies.

[Long-term dynamic of fecal corticosterone and its ecological and social correlates in males of great gerbil (Rhombomys opimus Licht.). Non-invasive approach in studies of stress in natural populations].

PubMed

Rogovin, K A; Tupikin, A A; Randall, J A; Kolosova, I E; Moshkin, M P

2006-01-01

The relationship between fecal corticosterone concentrations and characteristics of the environment and population demography were studied in adult male gerbils (Rhombomys opimus Licht.) at the southern border of Kyzylkum desert (Reserve "Ecocentre Dzeiran", Bukhara region, Republic Uzbekistan) in spring and fall seasons from 1999 to 2004. We extracted hormones from air-dried fecal samples and analyzed their concentrations by radioimmunoassay (Gerlinskaya et al., 1993). An analysis for year-specific relationships between hormone concentrations and environmental variables of temperature and precipitation using Pearson's r statistic revealed that corticosterone concentrations correlated positively with total precipitation in January and February and negatively with precipitation during March and April. There was also a significant negative relationship between fecal corticosterone and the number of hot days in March (>20 degrees C). Demographic variables that characterized population densities (percent of burrow systems occupied, mean and maximum number of burrow systems/1 ha, number of females in the burrow system) correlated positively with corticosterone concentrations in feces in the beginning of spring, but these relationships were small compared with mean concentrations of corticosterone for the entire spring season that were strongly and positively correlated with number of gerbils, including all pups emerged, in burrow systems owned by one male (within its home range). In contrast, correlation coefficients of corticosterone concentrations with characteristics of feeding resources in the spring were low and negative. In the long-term perspective (interannual comparison), mortality among adult males was highly negatively correlated with mean corticosterone concentrations in the beginning of spring, which is within the period of maximum reproductive effort and potential stress. Body mass was independent of corticosterone concentrations in males in either the beginning of spring, or during the whole spring. In the fall, mean concentrations of fecal corticosterone in males was positively correlated with the number of days from June to October with mean daily temperatures exceeding 30 degrees C, and with percent of burrow systems where at least one adult, > or = 1 year old gerbil had survived. Mortality from fall to spring of the next year and the fall body mass did not correlate with concentrations of corticosterone in feces collected in the fall. When we analyzed corticosterone concentrations in spring seasons of all years combined using a stepwise regression analysis of a sampling of individual males (we analyzed residuals after withdrawal of year effect) on a set of variables representing habitat resources, distances between nearest neighbor males, and variables representing group demography we found low R2 values not exceeding 0.17. Within the six-year period, concentrations of corticosterone in the spring related negatively with abundance of annual herbs and positively with number of females in a male's social group. When only years of high density were analyzed, fecal corticosterone concentrations in males in the spring were again negatively determined by abundance of herbs, as well as by the nearest neighbor distance, and positively determined by the number of females within a male's home range. At the beginning of spring the only determinants were distance to the nearest neighbor male and number of females. In years of low density none of the variables were found to affect corticosterone levels during the whole spring, while in the beginning of spring only partial regression coefficients of abundance of herbs were negative and significant. Stepwise logistic regression analysis revealed positive dependence (P = 0.05) of disappearance of adult males during summer drought on concentrations of fecal corticosterone in the spring, but only when burrow systems with at least one adult (male or female) surviving after the summer were considered. Our results provide evidence ground for the assumption that in a desert rodent with non-regular population fluctuations such as the great gerbil, density may be more suppressed by external factors and not by density dependent mortality mediated by stress. Density dependent increases of stress caused by intense reproductive effort occurred when feeding and climatic conditions were favorable to compensate for negative effects on survival. However, in individual gerbils mortality mediated by stress can take place because we found higher stress in the beginning of spring in males, which did not occur in the population after the summer drought.

Optimizing bulk milk dioxin monitoring based on costs and effectiveness.

PubMed

Lascano-Alcoser, V H; Velthuis, A G J; van der Fels-Klerx, H J; Hoogenboom, L A P; Oude Lansink, A G J M

2013-07-01

Dioxins are environmental pollutants, potentially present in milk products, which have negative consequences for human health and for the firms and farms involved in the dairy chain. Dioxin monitoring in feed and food has been implemented to detect their presence and estimate their levels in food chains. However, the costs and effectiveness of such programs have not been evaluated. In this study, the costs and effectiveness of bulk milk dioxin monitoring in milk trucks were estimated to optimize the sampling and pooling monitoring strategies aimed at detecting at least 1 contaminated dairy farm out of 20,000 at a target dioxin concentration level. Incidents of different proportions, in terms of the number of contaminated farms, and concentrations were simulated. A combined testing strategy, consisting of screening and confirmatory methods, was assumed as well as testing of pooled samples. Two optimization models were built using linear programming. The first model aimed to minimize monitoring costs subject to a minimum required effectiveness of finding an incident, whereas the second model aimed to maximize the effectiveness for a given monitoring budget. Our results show that a high level of effectiveness is possible, but at high costs. Given specific assumptions, monitoring with 95% effectiveness to detect an incident of 1 contaminated farm at a dioxin concentration of 2 pg of toxic equivalents/g of fat [European Commission's (EC) action level] costs €2.6 million per month. At the same level of effectiveness, a 73% cost reduction is possible when aiming to detect an incident where 2 farms are contaminated at a dioxin concentration of 3 pg of toxic equivalents/g of fat (EC maximum level). With a fixed budget of €40,000 per month, the probability of detecting an incident with a single contaminated farm at a dioxin concentration equal to the EC action level is 4.4%. This probability almost doubled (8.0%) when aiming to detect the same incident but with a dioxin concentration equal to the EC maximum level. This study shows that the effectiveness of finding an incident depends not only on the ratio at which, for testing, collected truck samples are mixed into a pooled sample (aiming at detecting certain concentration), but also the number of collected truck samples. In conclusion, the optimal cost-effective monitoring depends on the number of contaminated farms and the concentration aimed at detection. The models and study results offer quantitative support to risk managers of food industries and food safety authorities. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Estrus behavior, ovarian dynamics, and progesterone secretion in Criollo cattle during estrous cycles with two and three follicular waves.

PubMed

Quezada-Casasola, Andrés; Avendaño-Reyes, Leonel; Macías-Cruz, Ulises; Ramírez-Godínez, José Alejandro; Correa-Calderón, Abelardo

2014-04-01

In beef and dairy cattle, the number of follicular waves affects endocrine, ovarian, and behavioral events during a normal estrous cycle. However, in Mexican-native Criollo cattle, a shortly and recently domesticated breed, the association between wave patterns and follicular development has not been studied. The objective of this study was to evaluate the effect of number of follicular waves in an estrous cycle on development of anovulatory and ovulatory follicles, corpus luteum (CL) development and functionality, as well as estrual behavior in Criollo cows. Ovarian follicular activities of 22 cycling multiparous Criollo cows were recorded daily by transrectal ultrasound examinations during a complete estrous cycle. Additionally, blood samples were collected daily to determine serum progesterone concentrations. Only two- (n = 17, 77.3%) and three-wave follicular (n = 5, 22.7%) patterns were observed. Duration of estrus, length of estrous cycle, and length of follicular and luteal phases were similar (P > 0.05) between cycles of two and three waves. Two-wave cows ovulated earlier (P < 0.05) after detection of estrus than three-wave cows. Detected day and maximum diameter of first anovulatory follicle were not affected (P > 0.05) by number of waves. Growth rate of first dominant follicle was higher (P < 0.05) in three-wave cycles. Onset of regression of the first dominant follicle was earlier (P < 0.01) in cycles with three waves than in those with two waves. In two-wave cycles, ovulatory follicles were detected earlier (P < 0.01) and had lower (P < 0.01) growth rate than in three-wave cycles. Development (i.e., maximum diameter and volume) and functionality (minimum and maximum progesterone concentration) of CL were similar (P > 0.05) between two- and three-wave patterns. In conclusion, Criollo cows have two or three follicular waves per estrous cycle, which alters partially ovulatory follicle development and ovulation time after detection of estrus. Length of estrous cycle, as well as CL development and functionality, was not affected by number of follicular waves.

USSR and Eastern Scientific Abstracts, Biomedical and Behavioral Sciences, Number 62

DTIC Science & Technology

1977-01-18

this concentrate has valuable biological and nutritional properties. Maximum transition from the digestive tract into the blood stream has been... digestion . The extent of these changes 1/2 32 USSR LYCHAGIN, V. V., ADAMOVICH, G. G., MIKHAYLOVA, T. N., KUZLOVA, YU. G., KINZHIBALOVA, ZH. V...ANTIBIOTICS IN THE FEED OF BROILERS Sofia DOKLADY BOLGARSKOY AKADEMII NAUR" in English Vol 29 No 8 1976 pp 1177- 1178 [Abstract] Objections have

Nationwide reconnaissance of contaminants of emerging concern in source and treated drinking waters of the United States: Pharmaceuticals.

PubMed

Furlong, Edward T; Batt, Angela L; Glassmeyer, Susan T; Noriega, Mary C; Kolpin, Dana W; Mash, Heath; Schenck, Kathleen M

2017-02-01

Mobile and persistent chemicals that are present in urban wastewater, such as pharmaceuticals, may survive on-site or municipal wastewater treatment and post-discharge environmental processes. These pharmaceuticals have the potential to reach surface and groundwaters, essential drinking-water sources. A joint, two-phase U.S. Geological Survey-U.S. Environmental Protection Agency study examined source and treated waters from 25 drinking-water treatment plants from across the United States. Treatment plants that had probable wastewater inputs to their source waters were selected to assess the prevalence of pharmaceuticals in such source waters, and to identify which pharmaceuticals persist through drinking-water treatment. All samples were analyzed for 24 pharmaceuticals in Phase I and for 118 in Phase II. In Phase I, 11 pharmaceuticals were detected in all source-water samples, with a maximum of nine pharmaceuticals detected in any one sample. The median number of pharmaceuticals for all 25 samples was five. Quantifiable pharmaceutical detections were fewer, with a maximum of five pharmaceuticals in any one sample and a median for all samples of two. In Phase II, 47 different pharmaceuticals were detected in all source-water samples, with a maximum of 41 pharmaceuticals detected in any one sample. The median number of pharmaceuticals for all 25 samples was eight. For 37 quantifiable pharmaceuticals in Phase II, median concentrations in source water were below 113ng/L. For both Phase I and Phase II campaigns, substantially fewer pharmaceuticals were detected in treated water samples than in corresponding source-water samples. Seven different pharmaceuticals were detected in all Phase I treated water samples, with a maximum of four detections in any one sample and a median of two pharmaceuticals for all samples. In Phase II a total of 26 different pharmaceuticals were detected in all treated water samples, with a maximum of 20 pharmaceuticals detected in any one sample and a median of 2 pharmaceuticals detected for all 25 samples. Source-water type influences the presence of pharmaceuticals in source and treated water. Treatment processes appear effective in reducing concentrations of most pharmaceuticals. Pharmaceuticals more consistently persisting through treatment include carbamazepine, bupropion, cotinine, metoprolol, and lithium. Pharmaceutical concentrations and compositions from this study provide an important base data set for further sublethal, long-term exposure assessments, and for understanding potential effects of these and other contaminants of emerging concern upon human and ecosystem health. Copyright © 2016. Published by Elsevier B.V.

Hydrogen peroxide modulates Ca2+-activation of single permeabilized fibres from fast- and slow-twitch skeletal muscles of rats.

PubMed

Plant, D R; Lynch, G S; Williams, D A

2000-01-01

We examined the effects of redox modulation on single membrane-permeabilized fibre segments from the fast-twitch extensor digitorum longus (EDL) and slow-twitch soleus muscles of adult rats to determine whether the contractile apparatus was the redox target responsible for the increased contractility of muscles exposed to low concentrations of H2O2. The effects of H2O2 on maximum Ca2+-activated force were dose-dependent with 30 min exposure to 5 mM H2O2 causing a progressive decrease by 22+/-3 and 13+/-2% in soleus and EDL permeabilized muscle fibres, respectively. Lower concentrations of exogenous H2O2 (100 microM and 1 mM) had no effect on maximum Ca2+-activated force. Subsequent exposure to the reductant dithiothreitol (DTT, 10 mM, 10 min) fully reversed the H2O2-induced depression of force in EDL, but not in soleus muscle fibres. Incubation with DTT alone for 10 min did not alter Ca2+-activated force in either soleus or EDL muscle fibres. The sensitivity of the contractile filaments to Ca2+ (pCa50) was not altered by exposure to any concentration of exogenous H2O2. However, all concentrations of H2O2 diminished the Hill coefficient in permeabilized fibres from the EDL muscle, indicating that the cooperativity of Ca2+ binding to troponin is altered. H2O2 (5 mM) did not affect rigor force, which indicates that the number of crossbridges participating in contraction was not reduced. In conclusion, H2O2 may reduce the maximum Ca2+ activated force production in skinned muscle fibres by decreasing the force per crossbridge.

Systemic inflammatory responses to maximal versus submaximal lengthening contractions of the elbow flexors.

PubMed

Peake, Jonathan M; Nosaka, Kazunori; Muthalib, Makii; Suzuki, Katsuhiko

2006-01-01

We compared changes in markers of muscle damage and systemic inflammation after submaximal and maximal lengthening muscle contractions of the elbow flexors. Using a cross-over design, 10 healthy young men not involved in resistance training completed a submaximal trial (10 sets of 60 lengthening contractions at 10% maximum isometric strength, 1 min rest between sets), followed by a maximal trial (10 sets of three lengthening contractions at 100% maximum isometric strength, 3 min rest between sets). Lengthening contractions were performed on an isokinetic dynamometer. Opposite arms were used for the submaximal and maximal trials, and the trials were separated by a minimum of two weeks. Blood was sampled before, immediately after, 1 h, 3 h, and 1-4 d after each trial. Total leukocyte and neutrophil numbers, and the serum concentration of soluble tumor necrosis factor-alpha receptor 1 were elevated after both trials (P < 0.01), but there were no differences between the trials. Serum IL-6 concentration was elevated 3 h after the submaximal contractions (P < 0.01). The concentrations of serum tumor necrosis factor-alpha, IL-1 receptor antagonist, IL-10, granulocyte-colony stimulating factor and plasma C-reactive protein remained unchanged following both trials. Maximum isometric strength and range of motion decreased significantly (P < 0.001) after both trials, and were lower from 1-4 days after the maximal contractions compared to the submaximal contractions. Plasma myoglobin concentration and creatine kinase activity, muscle soreness and upper arm circumference all increased after both trials (P < 0.01), but were not significantly different between the trials. Therefore, there were no differences in markers of systemic inflammation, despite evidence of greater muscle damage following maximal versus submaximal lengthening contractions of the elbow flexors.

Pesticide concentrations in wetlands on the Lake Traverse Indian Reservation, South and North Dakota, July 2015

USGS Publications Warehouse

Carter, Janet M.; Thompson, Ryan F.

2016-05-04

During July 2015, water samples were collected from 18 wetlands on the Lake Traverse Indian Reservation in northeastern South Dakota and southeastern North Dakota and analyzed for physical properties and 54 pesticides. This study by the U.S. Geological Survey in cooperation with the Sisseton-Wahpeton Oyate was designed to provide an update on pesticide concentrations of the same 18 wetlands that were sampled for a reconnaissance-level assessment during July 2006. The purpose of this report is to present the results of the assessment of pesticide concentrations in selected Lake Traverse Indian Reservation wetlands during July 2015 and provide a comparison of pesticide concentrations between 2006 and 2015.Of the 54 pesticides that were analyzed for in the samples collected during July 2015, 47 pesticides were not detected in any samples. Seven pesticides—2-chloro-4-isopropylamino-6-amino-s-triazine (CIAT); 2,4–D; acetachlor; atrazine; glyphosate; metolachlor; and prometon—were detected in the 2015 samples with estimated concentrations or concentrations greater than the laboratory reporting level, and most pesticides were detected at low concentrations in only a few samples. Samples from all wetlands contained at least one detected pesticide. The maximum number of pesticides detected in a wetland sample was six, and the median number of pesticides detected was three.The most commonly detected pesticides in the 2015 samples were atrazine and the atrazine degradate CIAT (also known as deethylatrazine), which were detected in 14 and 13 of the wetlands sampled, respectively. Glyphosate was detected in samples from 11 wetlands, and metolachlor was detected in samples from 10 wetlands. The other detected pesticides were 2,4–D (4 wetlands), acetochlor (3 wetlands), and prometon (1 wetland).The same pesticides that were detected in the 2006 samples were detected in the 2015 samples, with the exception of simazine, which was detected only in one sample in 2006. Atrazine and CIAT were the most commonly detected pesticides in both sampling years; however, atrazine and CIAT were detected in fewer wetlands in 2015 (14 and 13 wetlands, respectively) than in 2006 (17 wetlands for both pesticides). The pesticides 2,4–D and prometon also were detected in fewer wetlands in 2015 than 2006, and simazine was only detected in 2006. In contrast, acetochlor, glyphosate, and metolachlor were detected in samples from more wetlands in 2015 than in 2006. In samples from individual wetlands, the number of pesticides detected was similar between 2006 and 2015. At least one pesticide was detected in all wetlands in 2015, and all but one wetland had pesticide detections in 2006.Concentrations of pesticides detected in samples from wetlands were compared to selected water-quality (human-health and aquatic-life) benchmarks. None of the concentrations in either 2006 or 2015 were greater than water-quality benchmarks, with the exception of atrazine. All detections of atrazine in the 2006 and 2015 samples were greater than the acute benchmark of 0.001 microgram per liter (μg/L) for vascular plants. In addition, some concentrations of 2,4–D and atrazine were within an order of magnitude of a water-quality benchmark. The 2,4–D concentrations in the 2015 samples from three wetlands were within an order of magnitude of the U.S. Environmental Protection Agency’s Maximum Contaminant Level of 70 μg/L (that is, sample concentrations were greater than 7.0 μg/L). The maximum dissolved atrazine concentration of 0.185 μg/L in the 2015 samples along with the concentrations in 2006 samples from two wetlands were within an order of magnitude of the acute benchmark of less than 1 μg/L for nonvascular plants (that is, concentrations were greater than 0.1 μg/L).

Impact of mixing state and hygroscopicity on CCN activity of biomass burning aerosol in Amazonia

NASA Astrophysics Data System (ADS)

Sánchez Gácita, Madeleine; Longo, Karla M.; Freire, Julliana L. M.; Freitas, Saulo R.; Martin, Scot T.

2017-02-01

Smoke aerosols prevail throughout Amazonia because of widespread biomass burning during the dry season, and external mixing, low variability in the particle size distribution and low particle hygroscopicity are typical. There can be profound effects on cloud properties. This study uses an adiabatic cloud model to simulate the activation of smoke particles as cloud condensation nuclei (CCN) for three hypothetical case studies, chosen as to resemble biomass burning aerosol observations in Amazonia. The relative importance of variability in hygroscopicity, mixing state, and activation kinetics for the activated fraction and maximum supersaturation is assessed. For a population with κp = 0.04, an overestimation of the cloud droplet number concentration Nd for the three selected case studies between 22.4 ± 1.4 and 54.3 ± 3.7 % was obtained when assuming a hygroscopicity parameter κp = 0.20. Assuming internal mixing of the aerosol population led to overestimations of up to 20 % of Nd when a group of particles with medium hygroscopicity was present in the externally mixed population cases. However, the overestimations were below 10 % for external mixtures between very low and low-hygroscopicity particles, as seems to be the case for Amazon smoke particles. Kinetic limitations were significant for medium- and high-hygroscopicity particles, and much lower for very low and low-hygroscopicity particles. When particles were assumed to be at equilibrium and to respond instantly to changes in the air parcel supersaturation, the overestimation of the droplet concentration was up to ˜ 100 % in internally mixed populations, and up to ˜ 250 % in externally mixed ones, being larger for the higher values of hygroscopicity. In addition, a perceptible delay between the times when maximum supersaturation and maximum aerosol activated fraction are reached was noticed and, for aerosol populations with effective hygroscopicity κpeff higher than a certain threshold value, the delay in particle activation was such that no particles were activated at the time of maximum supersaturation. Considering internally mixed populations, for an updraft velocity W = 0.5 m s-1 this threshold of no activation varied between κpeff = 0.35 and κpeff = 0.5 for the different case studies. However, for low hygroscopicity, kinetic limitations played a weaker role for CCN activation of particles, even when taking into account the large aerosol mass and number concentrations. For the very low range of hygroscopicities, the overestimation of the droplet concentration due to the equilibrium assumption was lowest and the delay between the times when maximum supersaturation and maximum activated fraction were reached was greatly reduced or no longer observed (depending on the case study). These findings on uncertainties and sensitivities provide guidance on appropriate simplifications that can be used for modeling of smoke aerosols within general circulation models. The use of medium values of hygroscopicity representative of smoke aerosols for other biomass burning regions on Earth can lead to significant errors compared to the use of low hygroscopicity for Amazonia (between 0.05 and 0.13, according to available observations). Also in this region, consideration of the biomass burning population as internally mixed will lead to small errors in the droplet concentration, while significantly increasing the computational burden. Regardless of the large smoke aerosol loads in the region during the dry season, kinetic limitations are expected to be low.

Final Report One-Twelfth-Scale Mixing Experiments to Characterize Double-Shell Tank Slurry Uniformity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bamberger, Judith A.; Liljegren, Lucia M.; Enderlin, Carl W.

The objectives of these 1/12-scale scoping experiments were to: Determine which of the dimensionless parameters discussed in Bamberger and Liljegren (1994) affect the maximum concentration that can be suspended during jet mixer pump operation in the full-scale double-shell tanks; Develop empirical correlations to predict the nozzle velocity required for jet mixer pumps to suspend the contents of full-scale double-shell tanks; Apply the models to predict the nozzle velocity required to suspend the contents of Tank 241 AZ-101; Obtain experimental concentration data to compare with the TEMPEST( )(Trent and Eyler 1989) computational modeling predictions to guide further code development; Analyze themore » effects of changing nozzle diameter on exit velocity (U0) and U0D0 (the product of the exit velocity and nozzle diameter) required to suspend the contents of a tank. The scoping study experimentally evaluated uniformity in a 1/12-scale experiment varying the Reynolds number, Froude number, and gravitational settling parameter space. The initial matrix specified only tests at 100% U0D0 and 25% U0D0. After initial tests were conducted with small diameter, low viscosity simulant this matrix was revised to allow evaluation of a broader range of U0D0s. The revised matrix included full factorial test between 100% and 50% U0D0 and two half-factorial tests at 75% and 25% U0D0. Adding points at 75% U0D0 and 50% U0D0 allowed evaluation curvature. Eliminating points at 25% U0D0 decreased the testing time by several weeks. Test conditions were achieved by varying the simulant viscosity, the mean particle size, and the jet nozzle exit velocity. Concentration measurements at sampling locations throughout the tank were used to assess the degree of uniformity achieved during each test. Concentration data was obtained using a real time ultrasonic attenuation probe and discrete batch samples. The undissolved solids concentration at these locations was analyzed to determine whether the tank contents were uniform (< ±10% variation about mean) or nonuniform (> ±10% variation about mean) in concentration. Concentration inhomogeneity was modeled as a function of dimensionless groups. The two parameters that best describe the maximum solids volume fraction that can be suspended in a double-shell tank were found to be 1) the Froude number (Fr) based on nozzle velocity (U0) and tank contents level (H) and 2) the dimensionless particle size (dp/D0). The dependence on the Reynolds number (Re) does not appear to be statistically significant.« less

Inner filter effect and the onset of concentration dependent red shift of synchronous fluorescence spectra.

PubMed

Tarai, Madhumita; Mishra, Ashok Kumar

2016-10-12

The phenomenon of concentration dependent red shift, often observed in synchronous fluorescence spectra (SFS) of monofluorophoric as well as multifluorophoric systems at high chromophore concentrations, is known to have good analytical advantages. This was previously understood in terms of large inner filter effect (IFE) through the introduction of a derived absorption spectral profile that closely corresponds to the SFS profile. Using representative monofluorophoric and multifluorophoric systems, it is now explained how the SF spectral maximum changes with concentration of the fluorophore. For dilute solutions of monofluorophores the maximum is unchanged as expected. It is shown here that the onset of red shift of SFS maximum of both the mono as well as the multifluorophoric systems must occur at the derived absorption spectral parameter value of 0.32 that corresponds to the absorbance value of 0.87. This value is unique irrespective of the nature of the fluorophore under study. For monofluorophoric systems, the wavelength of derived absorption spectral maximum and the wavelength of synchronous fluorescence spectral maximum closely correspond with each other in the entire concentration range. In contrast, for multifluorophoric systems like diesel and aqueous humic acid, large deviations were noted that could be explained as to be due to the presence of non-fluorescing chromophores in the system. This work bridges the entire fluorophore concentration range over which the red shift of SFS maximum sets in; and in the process it establishes the importance of the derived absorption spectral parameter in understanding the phenomenon of concentration dependent red shift of SFS maximum. Copyright © 2016 Elsevier B.V. All rights reserved.

Particle bombardment - mediated gene transfer and GFP transient expression in Seteria viridis.

PubMed

Mookkan, Muruganantham

2018-04-03

Setaria viridis is one of the most important model grasses in studying monocot plant biology. Transient gene expression study is a very important tool in plant biotechnology, functional genomics, and CRISPR-Cas9 genome editing technology via particle bombardment. In this study, a particle bombardment-mediated protocol was developed to introduce DNA into Setaria viridis in vitro leaf explants. In addition, physical and biological parameters, such as helium pressure, distance from stopping screen to the target tissues, DNA concentration, and number of bombardments, were tested and optimized. Optimum concentration of transient GFP expression was achieved using 1.5 ug plasmid DNA with 0.6 mm gold particles and 6 cm bombardment distance, using 1,100 psi. Doubling the bombardment instances provides the maximum number of foci of transient GFP expression. This simple protocol will be helpful for genomics studies in the S. viridis monocot model.

38 CFR 59.40 - Maximum number of nursing home care and domiciliary care beds for veterans by State.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Maximum number of nursing... ACQUISITION OF STATE HOMES § 59.40 Maximum number of nursing home care and domiciliary care beds for veterans... increase the total number of state home nursing home and domiciliary beds in that state beyond the maximum...

38 CFR 59.40 - Maximum number of nursing home care and domiciliary care beds for veterans by State.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2011-07-01 2011-07-01 false Maximum number of nursing... ACQUISITION OF STATE HOMES § 59.40 Maximum number of nursing home care and domiciliary care beds for veterans... increase the total number of state home nursing home and domiciliary beds in that state beyond the maximum...

38 CFR 59.40 - Maximum number of nursing home care and domiciliary care beds for veterans by State.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2012-07-01 2012-07-01 false Maximum number of nursing... ACQUISITION OF STATE HOMES § 59.40 Maximum number of nursing home care and domiciliary care beds for veterans... increase the total number of state home nursing home and domiciliary beds in that state beyond the maximum...

38 CFR 59.40 - Maximum number of nursing home care and domiciliary care beds for veterans by State.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2014-07-01 2014-07-01 false Maximum number of nursing... ACQUISITION OF STATE HOMES § 59.40 Maximum number of nursing home care and domiciliary care beds for veterans... increase the total number of state home nursing home and domiciliary beds in that state beyond the maximum...

38 CFR 59.40 - Maximum number of nursing home care and domiciliary care beds for veterans by State.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2013-07-01 2013-07-01 false Maximum number of nursing... ACQUISITION OF STATE HOMES § 59.40 Maximum number of nursing home care and domiciliary care beds for veterans... increase the total number of state home nursing home and domiciliary beds in that state beyond the maximum...

Environmental land use conflicts in catchments: A major cause of amplified nitrate in river water.

PubMed

Pacheco, F A L; Sanches Fernandes, L F

2016-04-01

Environmental land use conflicts are uses of the land that ignore soil capability. In this study, environmental land use conflicts were investigated in mainland Portugal, using Partial Least Squares (PLS) regression combined with GIS modeling and a group of 85 agricultural watersheds (with >50% occupation by agriculture) as work sample. The results indicate a dominance of conflicts in a region where vineyards systematically invaded steep hillsides (the River Douro basin), where forests would be the most appropriate use. As a consequence of the conflicts, nitrate concentrations in rivers and lakes from these areas have increased, sometimes beyond the legal limit of 50mg/L imposed by the European and Portuguese laws. Excessive nitrate concentrations were also observed along the Atlantic coast of continental Portugal, but associated to a combination of other factors: large population densities, and incomplete coverage by sewage systems and inadequate functioning of wastewater treatment plants. Before this study, environmental land use conflicts were never recognized as possible boost of nitrate concentrations in surface water. Bearing in mind the consequences of drinking water nitrate for human health, a number of land use change scenarios were investigated to forecast their impact on freshwater nitrate concentrations. It was seen that an aggravation of the conflicts would duplicate the number of watersheds with maximum nitrate concentrations above 50mg/L (from 11 to 20 watersheds), while the elimination of the conflicts would greatly reduce that number (to 3 watersheds). Copyright © 2016 Elsevier B.V. All rights reserved.

Isotope effects of trapped electron modes in the presence of impurities in tokamak plasmas

NASA Astrophysics Data System (ADS)

Shen, Yong; Dong, J. Q.; Sun, A. P.; Qu, H. P.; Lu, G. M.; He, Z. X.; He, H. D.; Wang, L. F.

2016-04-01

The trapped electron modes (TEMs) are numerically investigated in toroidal magnetized hydrogen, deuterium and tritium plasmas, taking into account the effects of impurity ions such as carbon, oxygen, helium, tungsten and others with positive and negative density gradients with the rigorous integral eigenmode equation. The effects of impurity ions on TEMs are investigated in detail. It is shown that impurity ions have substantially-destabilizing (stabilizing) effects on TEMs in isotope plasmas for {{L}ez}\\equiv {{L}ne}/{{L}nz}>0 (<0 ), opposite to the case of ion temperature gradient (ITG) driven modes. Detailed analyses of the isotope mass dependence for TEM turbulences in hydrogenic isotope plasmas with and without impurities are performed. The relations between the maximum growth rate of the TEMs with respect to the poloidal wave number and the ion mass number are given in the presence of the impurity ions. The results demonstrate that the maximum growth rates scale as {γ\\max}\\propto Mi-0.5 in pure hydrogenic plasmas. The scale depends on the sign of its density gradient and charge number when there is a second species of (impurity) ions. When impurity ions have density profiles peaking inwardly (i.e. {{L}ez}\\equiv {{L}ne}/{{L}nz}>0 ), the scaling also depends on ITG parameter {ηi} . The maximum growth rates scale as {γ\\max}\\propto M\\text{eff}-0.5 for the case without ITG ({ηi}=0 ) or the ITG parameter is positive ({ηi}>0 ) but the impurity ion charge number is low (Z≤slant 5.0 ). However, when {ηi}>0 and the impurity ion charge number is moderate (Z=6.0-8.0 ), the scaling law is found as {γ\\max}\\propto M\\text{eff}-1.0 . Here, Z is impurity ion charge number, and the effective mass number, {{M}\\text{eff}}=≤ft(1-{{f}z}\\right){{M}i}+{{f}z}{{M}z} , with {{M}i} and {{M}Z} being the mass numbers of the hydrogenic and impurity ions, respectively, and {{f}z}=Z{{n}0z}/{{n}0e} being the charge concentration of impurity ions. In addition, with regard to the case of {{L}ez}<0 , the maximum growth rate scaling is {γ\\max}\\propto Mi-0.5 . The possible relations of the results with experimental observations are discussed.

Assessing the guidelines for potassium replacement in pediatric oncology patients receiving amphotericin B.

PubMed

Lafreniere, Janet A; Hamilton, Donald P; Carr, Roxane R

2006-10-01

To examine the practice of potassium chloride (KCl) replacement in pediatric oncology patients receiving amphotericin B (amp-B). A retrospective observational chart review was conducted of patients who received amp-B on the oncology unit between August 2000 and May 2001. A survey was distributed to pediatric oncology pharmacists at other pediatric institutions to assess KCl infusion guidelines across North America. Twenty hypokalemic episodes were identified within 22 patient admissions. Fifty-five percent used KCl replacement (by all combined routes) at rates exceeding the institution's guidelines. Other pediatric institutions varied with respect to the maximum rates and concentration of KCl permitted on non-intensive care units. Based on the data from this review, the KCl administration guidelines for our hospital were changed. We now allow a maximum peripheral line concentration of 60 mEq/L, a maximum central line concentration of 120 mEq/L and a maximum KCl infusion rate of 0.4 mEq/kg/hr without the requirement of a heart monitor. Parenteral Nutrition is now restricted to maximum potassium concentration of 80 mEq/L and fluid-restricted patients are restricted to a maximum concentration of 150 mEq/L.

Laboratory and on-road evaluations of cabin air filters using number and surface area concentration monitors.

PubMed

Qi, Chaolong; Stanley, Nick; Pui, David Y H; Kuehn, Thomas H

2008-06-01

An automotive cabin air filter's effectiveness for removing airborne particles was determined both in a laboratory wind tunnel and in vehicle on-road tests. The most penetrating particle size for the test filter was approximately 350 nm, where the filtration efficiency was 22.9 and 17.4% at medium and high fan speeds, respectively. The filtration efficiency increased for smaller particles and was 43.9% for 100 nm and 72.0% for 20 nm particles at a medium fan speed. We determined the reduction in passenger exposure to particles while driving in freeway traffic caused by a vehicle ventilation system with a cabin air filter installed. Both particle number and surface area concentration measurements were made inside the cabin and in the surrounding air. At medium fan speed, the number and surface area concentration-based exposure reductions were 65.6 +/- 6.0% and 60.6 +/- 9.4%, respectively. To distinguish the exposure reduction contribution from the filter alone and the remainder of the ventilation system, we also performed tests with and without the filter in place using the surface area monitors. The ventilation system operating in the recirculation mode with the cabin air filter installed provided the maximum protection, reducing the cabin particle concentration exponentially over time and usually taking only 3 min to reach 10 microm2/cm3 (a typical office air condition) under medium fan speed.

Guidelines for developing spacecraft maximum allowable concentrations for Space Station contaminants

NASA Technical Reports Server (NTRS)

1992-01-01

The National Aeronautics and Space Administration (NASA) is preparing to launch a manned space station by the year 1996. Because of concerns about the health, safety, and functioning abilities of the crews, NASA has requested that the National Research Council (NRC) through the Board on Environmental Studies and Toxicology (BEST) provide advice on toxicological matters for the space-station program. The Subcommittee on Guidelines for Developing Spacecraft Maximum Allowable Concentrations for Space Station Contaminants was established by the Committee on Toxicology (COT) to address NASA's concerns. Spacecraft maximum allowable concentrations (SMAC's) are defined as the maximum concentrations of airborne substances (such as gas, vapor, or aerosol) that will not cause adverse health effects, significant discomfort, or degradation in crew performance.

Water-quality assessment of the Ozark Plateaus study unit, Arkansas, Kansas, Missouri, and Oklahoma- summary of information on pesticides, 1970-90

USGS Publications Warehouse

Bell, Richard W.; Joseph, Robert L.; Freiwald, David A.

1996-01-01

Historical pesticide data from 1970-90 were compiled for 140 surface-water, 92 ground-water, 55 streambed-sediment, and 120 biological-tissue sampling sites within the Ozark Plateaus National Water-Quality Assessment Program study unit. Surface-water, bed-sediment, and biological-tissue sites have drainage basins predominantly in the Springfield and Salem Plateaus; ground-water sites are predominantly located in the Osage Plains and Mississippi Alluvial Plain. Many sites were sampled only once or twice during this period. A large percentage of the samples were collected in the mid-1970's and early 1980's for surface water, 1990 for ground water, the late 1980's for surface water, 1990 for ground water, the late 1980's for bed sediment, and the early 1980's for biological tissue. Pesticide use was approximately 4.2 million pounds per year of active ingredients from 1982-85 in the study unit and was generally greatest in the Springfield and Salem Plateaus pasturelands and in the Osage Plains and Mississippi Alluvial Plain cropland areas. The most frequently applied pesticide in the study unit was 2,4-D. Alachlor was the second most applied pesticide. Corn, pasture, rice, sorghum, and soybeans received approximately 90 percent of the pesticides applied within the study unit. The highest pesticide application rate per acre occurred on these crops in the Osage Plains and Mississippi Alluvial Plain. Pastureland was the predominant crop type in 50 of the 94 counties in the study unit. Toxaphene, the pesticide having the most number of detections in surface water, was found in 17 of 866 samples from 5 of 112 sites. Concentrations ranged from 0.1 to 6.0 micrograms per liter. Six other pesticides or pesticide metabolites were detected in 12 or more surface-water samples: DDE, dieldrin, DDT, aldrin, 2,4-D, and lindane. The maximum concentration for these pesticides was less than 1.0 micrograms per liter. Atrazine, the pesticide having the most number of detections in ground water, was found in 15 of 95 samples from 15 of 79 wells with concentrations ranging from 0.1 to 8.2 micrograms per liter. Metolachlor, alachlor, and prometon were detected more than once with maximum concentrations less than 1.0 micrograms per liter, except for prometon (2.4 micrograms per liter). Chlordane was the pesticide having the most number of detections in bed sediment and biological tissue. Chlordane was detected in 12 of 73 samples from 10 of 45 bed-sediment sites with concentrations ranging from 2.0 to 240 micrograms per kilogram. In biological tissue, chlordane was found in 93 of 151 samples from 39 of 53 sites with concentrations ranging from 0.009 to 8.6 milligrams per kilogram. Other pesticides or pesticide metabolites detected more than once in bed sediment include DDT, DDD, p,p'-DDE, DDE, and hexachlorobenzene and in biological tissue include DDT, p,p'-DDE, and hexachlorobenzene. Quality criteria or standards have been established for 15 of the pesticides detected in the study unit. For surface-water samples, the drinking water maximum contaminant level for alachlor was exceeded in one sample from one site in 1982. For ground-water samples, the drinking water maximum contaminant level for atrazine was exceeded in four samples from four wells in 1990. For biological-tissue samples collected during the years 1982-89, the fish tissue action levels for chlordane (19 sites; 26 samples), heptachlor epoxide (3 sites; 3 samples), p,p'-DDE (2 sites; 2 samples), dieldrin (2 sites, 2 samples), and mirex (1 site; 1 sample) were exceeded. For bed-sediment samples, quality criteria or standards were not exceeded for any pesticide. Pesticides do not pose any widespread or persistent problems in the study unit, based on the limited number of samples that exceeded quality criteria and standards.

Muscular fatigue in response to different modalities of CrossFit sessions

PubMed Central

Maté-Muñoz, José Luis; Lougedo, Juan H.; Barba, Manuel; García-Fernández, Pablo

2017-01-01

Background CrossFit is a new strength and conditioning regimen involving short intense daily workouts called workouts of the day (WOD). This study assesses muscular fatigue levels induced by the three modalities of CrossFit WOD; gymnastics (G), metabolic conditioning (M) and weightlifting (W). Material and methods 34 healthy subjects undertook three WOD (one per week): a G WOD consisting of completing the highest number of sets of 5 pull-ups, 10 push-ups and 15 air squats in 20 min; an M WOD, in which the maximum number of double skipping rope jumps was executed in 8 sets (20 s), resting (10 s) between sets; and finally, a W WOD in which the maximum number of power cleans was executed in 5 min, lifting a load equivalent to 40% of the individual's 1RM. Before and after each WOD, blood lactate concentrations were measured. Also, before, during, and after each WOD, muscular fatigue was assessed in a countermovement jump test (CMJ). Results Significant reductions were produced in the mechanical variables jump height, average power and maximum velocity in response to G; and in jump height, mean and peak power, maximum velocity and maximum force in response to W (P<0.01). However, in M, significant reductions in mechanical variables were observed between pre- and mid session (after sets 2, 4, 6 and 8), but not between pre- and post session. Conclusions Muscular fatigue, reflected by reduced CMJ variables, was produced following the G and W sessions, while recovery of this fatigue was observed at the end of M, likely attributable to rest intervals allowing for the recovery of phosphocreatine stores. Our findings also suggest that the high intensity and volume of exercise in G and W WODs could lead to reduced muscular-tendon stiffness causing a loss of jump ability, related here to a longer isometric phase during the CMJ. PMID:28753624

Muscular fatigue in response to different modalities of CrossFit sessions.

PubMed

Maté-Muñoz, José Luis; Lougedo, Juan H; Barba, Manuel; García-Fernández, Pablo; Garnacho-Castaño, Manuel V; Domínguez, Raúl

2017-01-01

CrossFit is a new strength and conditioning regimen involving short intense daily workouts called workouts of the day (WOD). This study assesses muscular fatigue levels induced by the three modalities of CrossFit WOD; gymnastics (G), metabolic conditioning (M) and weightlifting (W). 34 healthy subjects undertook three WOD (one per week): a G WOD consisting of completing the highest number of sets of 5 pull-ups, 10 push-ups and 15 air squats in 20 min; an M WOD, in which the maximum number of double skipping rope jumps was executed in 8 sets (20 s), resting (10 s) between sets; and finally, a W WOD in which the maximum number of power cleans was executed in 5 min, lifting a load equivalent to 40% of the individual's 1RM. Before and after each WOD, blood lactate concentrations were measured. Also, before, during, and after each WOD, muscular fatigue was assessed in a countermovement jump test (CMJ). Significant reductions were produced in the mechanical variables jump height, average power and maximum velocity in response to G; and in jump height, mean and peak power, maximum velocity and maximum force in response to W (P<0.01). However, in M, significant reductions in mechanical variables were observed between pre- and mid session (after sets 2, 4, 6 and 8), but not between pre- and post session. Muscular fatigue, reflected by reduced CMJ variables, was produced following the G and W sessions, while recovery of this fatigue was observed at the end of M, likely attributable to rest intervals allowing for the recovery of phosphocreatine stores. Our findings also suggest that the high intensity and volume of exercise in G and W WODs could lead to reduced muscular-tendon stiffness causing a loss of jump ability, related here to a longer isometric phase during the CMJ.

Beta-Adrenergic Receptor Population is Up-Regulated by Increased Cyclic Amp Concentration in Chicken Skeletal Muscle Cells in Culture

NASA Technical Reports Server (NTRS)

Young, Ronald B.; Bridge, Kristin Y.; Vaughn, Jeffrey R.

1999-01-01

Skeletal muscle hypertrophy is promoted in vivo by administration of beta-drenergic receptor (bAR) agonists. Chicken skeletal muscle cells were treated with 1 (mu)M isoproterenol, a strong bAR agonist, between days 7 and 10 in culture. bAR population increased by approximately 40% during this treatment; however, the ability of the cells to synthesize cyclic AMP (cAMP) was diminished by two-fold. The quantity of myosin heavy chain (MHC) was not affected. To understand further the relationship between intracellular cAMP levels, bAR population, and muscle protein accumulation, intracellular cAMP levels were artificially elevated by treatment with 0-10 uM forskolin for up to three days. The basal concentration of CAMP in forskolin-treated cells increased up to 7-fold in a dose dependent manner. Increasing concentrations of forskolin also led to an increase in bAR population, with a maximum increase of approximately 40-60% at 10 uM forskolin. A maximum increase of 40-50% in the quantity of MHC was observed at 0.2 uM forskolin, but higher concentrations of forskolin reduced the quantity of MHC back to control levels. At 0.2 uM forskolin, intracellular levels of cAMP were higher by approximately 35%, and the (beta)AR population was higher by approximately 30%. Neither the number of muscle nuclei fused into myotubes nor the percentage of nuclei in myotubes were affected by forskolin at any of the concentrations studied.

Critical Concentration Ratio for Solar Thermoelectric Generators

NASA Astrophysics Data System (ADS)

ur Rehman, Naveed; Siddiqui, Mubashir Ali

2016-10-01

A correlation for determining the critical concentration ratio (CCR) of solar concentrated thermoelectric generators (SCTEGs) has been established, and the significance of the contributing parameters is discussed in detail. For any SCTEG, higher concentration ratio leads to higher temperatures at the hot side of modules. However, the maximum value of this temperature for safe operation is limited by the material properties of the modules and should be considered as an important design constraint. Taking into account this limitation, the CCR can be defined as the maximum concentration ratio usable for a particular SCTEG. The established correlation is based on factors associated with the material and geometric properties of modules, thermal characteristics of the receiver, installation site attributes, and thermal and electrical operating conditions. To reduce the number of terms in the correlation, these factors are combined to form dimensionless groups by applying the Buckingham Pi theorem. A correlation model containing these groups is proposed and fit to a dataset obtained by simulating a thermodynamic (physical) model over sampled values acquired by applying the Latin hypercube sampling (LHS) technique over a realistic distribution of factors. The coefficient of determination and relative error are found to be 97% and ±20%, respectively. The correlation is validated by comparing the predicted results with literature values. In addition, the significance and effects of the Pi groups on the CCR are evaluated and thoroughly discussed. This study will lead to a wide range of opportunities regarding design and optimization of SCTEGs.

Regulation of Hippocampal Glutamate Receptors: Evidence for the Involvement of a Calcium-Activated Protease

NASA Astrophysics Data System (ADS)

Baudry, Michel; Lynch, Gary

1980-04-01

Specific [3H]glutamate binding to rat hippocampal membranes and the calcium-induced increase in this binding are markedly temperature-sensitive and are inhibited by alkylating or reducing agents as well as by various protease inhibitors. N-Ethylmaleimide, chloromethyl ketone derivatives of lysine and phenylalanine, and tosylarginine methyl ester decrease the maximum number of [3H]glutamate binding sites without changing their affinity for glutamate. Preincubation of the membranes with glutamate does not protect the glutamate ``receptors'' from the suppressive effects of these agents. The proteases trypsin and α -chymotrypsin increase the maximum number of [3H]glutamate binding sites. The effects of calcium on glutamate binding are different across brain regions. Cerebellar membranes are almost insensitive whereas hippocampal and striatal membranes exhibit a strong increase in the number of binding sites after exposure to even low concentrations of calcium. These results suggest that an endogenous membrane-associated thiol protease regulates the number of [3H]glutamate binding sites in hippocampal membranes and that this is the mechanism by which calcium stimulates glutamate binding. The possibility is discussed that the postulated mechanisms participate in synaptic physiology and in particular may be related to the long-term potentiation of transmission found in hippocampus under certain conditions.

Reconstructing Historical VOC Concentrations in Drinking Water for Epidemiological Studies at a U.S. Military Base: Summary of Results

PubMed Central

Maslia, Morris L.; Aral, Mustafa M.; Ruckart, Perri Z.; Bove, Frank J.

2017-01-01

A U.S. government health agency conducted epidemiological studies to evaluate whether exposures to drinking water contaminated with volatile organic compounds (VOC) at U.S. Marine Corps Base Camp Lejeune, North Carolina, were associated with increased health risks to children and adults. These health studies required knowledge of contaminant concentrations in drinking water—at monthly intervals—delivered to family housing, barracks, and other facilities within the study area. Because concentration data were limited or unavailable during much of the period of contamination (1950s–1985), the historical reconstruction process was used to quantify estimates of monthly mean contaminant-specific concentrations. This paper integrates many efforts, reports, and papers into a synthesis of the overall approach to, and results from, a drinking-water historical reconstruction study. Results show that at the Tarawa Terrace water treatment plant (WTP) reconstructed (simulated) tetrachloroethylene (PCE) concentrations reached a maximum monthly average value of 183 micrograms per liter (μg/L) compared to a one-time maximum measured value of 215 μg/L and exceeded the U.S. Environmental Protection Agency’s current maximum contaminant level (MCL) of 5 μg/L during the period November 1957–February 1987. At the Hadnot Point WTP, reconstructed trichloroethylene (TCE) concentrations reached a maximum monthly average value of 783 μg/L compared to a one-time maximum measured value of 1400 μg/L during the period August 1953–December 1984. The Hadnot Point WTP also provided contaminated drinking water to the Holcomb Boulevard housing area continuously prior to June 1972, when the Holcomb Boulevard WTP came on line (maximum reconstructed TCE concentration of 32 μg/L) and intermittently during the period June 1972–February 1985 (maximum reconstructed TCE concentration of 66 μg/L). Applying the historical reconstruction process to quantify contaminant-specific monthly drinking-water concentrations is advantageous for epidemiological studies when compared to using the classical exposed versus unexposed approach. PMID:28868161

Optimization of L(+)-Lactic Acid Fermentation Without Neutralisation of Rhizopus Oryzae Mutant RK02 by Low-Energy Ion Implantation

NASA Astrophysics Data System (ADS)

Li, Wen; Wang, Tao; Yang, Yingge; Liu, Dan; Fan, Yonghong; Wang, Dongmei; Yang, Qian; Yao, Jianming; Zheng, Zhiming; Yu, Zengliang

2008-04-01

In order to get an industrial strain which can yield a high concentration of lactic acid for ISPR (in situ product removal), the original strain Rhizopus oryzae RE3303 was mutated by low-energy ion beam implantation. A mutant RK02 was screened, and the factors such as the substrate concentration, nitrogen source concentration, inoculum size, seed age, aeration and temperature that affect the production of lactic acid were studied in detail. Under optimal conditions, the maximum concentration of L(+)-lactic acid reached 34.85 g/L after 30 h shake-flask cultivation without adding any neutralisation (5% Glucose added), which was a 146% increase in lactic acid production after ion implantation compared with the original strain. It was also shown that RK02 can be used in ISPR to reduce the number of times of separation.

Simulated ground-water flow and water quality of the Mississippi River alluvium near Burlington, Iowa, 1999

USGS Publications Warehouse

Boyd, Robert A.

2001-01-01

Water samples collected from the alluvium indicated ground water can be classified as a calcium-magnesium-bicarbonate type. Reducing conditions likely occur in some localized areas of the alluvium, as suggested by relatively large concentrations of dissolved iron (4,390 micrograms per liter) and manganese (2, 430 micrograms per liter) in some ground-water samples. Nitrite plus nitrate was detected at concentrations greater than or equal to 8 milligrams per liter in three samples collected from observation wells completed in close proximity to cropland; the nitrite plus nitrate concentration in one groundwater sample exceeded the U.S. Environmental Protection Agency Maximum Contaminant Level for nitrate in drinking water (10 milligrams per liter as N). Triazine herbicides (atrazine, cyanazine, propazine, simazine, and selected degradation products) and chloroacetanilide herbicides (acetochlor, alachlor, and metolachlor) were detected in some water samples. A greater number of herbicide compounds were detected in surface-water samples than in ground-water samples. Herbicide concentrations typically were at least an order of magnitude greater in surfacewater samples than in ground-water samples. The Maximum Contaminant Level for alachlor (2 micrograms per liter) was exceeded in a sample from Dry Branch Creek at Tama Road and for atrazine (3 micrograms per liter) was exceeded in samples collected from Dry Branch Creek at Tama Road and the county drainage ditch at Tama Road.

Impact of downward-mixing ozone on surface ozone accumulation in southern Taiwan.

PubMed

Lin, Ching-Ho

2008-04-01

The ozone that initially presents in the previous day's afternoon mixing layer can remain in the nighttime atmosphere and then be carried over to the next morning. Finally, this ozone can be brought to the ground by downward mixing as mixing depth increases during the daytime, thereby increasing surface ozone concentrations. Variation of ozone concentration during each of these periods is investigated in this work. First, ozone concentrations existing in the daily early morning atmosphere at the altitude range of the daily maximum mixing depth (residual ozone concentrations) were measured using tethered ozonesondes on 52 experimental days during 2004-2005 in southern Taiwan. Daily downward-mixing ozone concentrations were calculated by a box model coupling the measured daily residual ozone concentrations and daily mixing depth variations. The ozone concentrations upwind in the previous day's afternoon mixing layer were estimated by the combination of back air trajectory analysis and known previous day's surface ozone distributions. Additionally, the relationship between daily downward-mixing ozone concentration and daily photochemically produced ozone concentration was examined. The latter was calculated by removing the former from daily surface maximum ozone concentration. The measured daily residual ozone concentrations distributed at 12-74 parts per billion (ppb) with an average of 42 +/- 17 ppb are well correlated with the previous upwind ozone concentration (R2 = 0.54-0.65). Approximately 60% of the previous upwind ozone was estimated to be carried over to the next morning and became the observed residual ozone. The daily downward-mixing ozone contributes 48 +/- 18% of the daily surface maximum ozone concentration, indicating that the downward-mixing ozone is as important as daily photochemically produced ozone to daily surface maximum ozone accumulation. The daily downward-mixing ozone is poorly correlated with the daily photochemically produced ozone and contributes significantly to the daily variation of surface maximum ozone concentrations (R2 = 0.19). However, the contribution of downward-mixing ozone to daily ozone variation is not included in most existing statistical models developed for predicting daily ozone variation. Finally, daily surface maximum ozone concentration is positively correlated with daily afternoon mixing depth, attributable to the downward-mixing ozone.

Emissions from an international airport increase particle number concentrations 4-fold at 10 km downwind.

PubMed

Hudda, Neelakshi; Gould, Tim; Hartin, Kris; Larson, Timothy V; Fruin, Scott A

2014-06-17

We measured the spatial pattern of particle number (PN) concentrations downwind from the Los Angeles International Airport (LAX) with an instrumented vehicle that enabled us to cover larger areas than allowed by traditional stationary measurements. LAX emissions adversely impacted air quality much farther than reported in previous airport studies. We measured at least a 2-fold increase in PN concentrations over unimpacted baseline PN concentrations during most hours of the day in an area of about 60 km(2) that extended to 16 km (10 miles) downwind and a 4- to 5-fold increase to 8-10 km (5-6 miles) downwind. Locations of maximum PN concentrations were aligned to eastern, downwind jet trajectories during prevailing westerly winds and to 8 km downwind concentrations exceeded 75 000 particles/cm(3), more than the average freeway PN concentration in Los Angeles. During infrequent northerly winds, the impact area remained large but shifted to south of the airport. The freeway length that would cause an impact equivalent to that measured in this study (i.e., PN concentration increases weighted by the area impacted) was estimated to be 280-790 km. The total freeway length in Los Angeles is 1500 km. These results suggest that airport emissions are a major source of PN in Los Angeles that are of the same general magnitude as the entire urban freeway network. They also indicate that the air quality impact areas of major airports may have been seriously underestimated.

In vitro callus induction and plantlet regeneration of Achyranthes aspera L., a high value medicinal plant

PubMed Central

Sen, Monokesh Kumer; Nasrin, Shamima; Rahman, Shahedur; Jamal, Abu Hena Mostofa

2014-01-01

Objective To study callus induction from different explants (internode, leaf, root) and in vitro plantlets propagation from medicinally important plant Achyranthes aspera L. Methods Sterilized explants were prepared by using 0.1% HgCl2 and 0.5% Bavistin and callus was obtained when cultured onto Murashige Skoog's (MS) medium by using different concentrations and combination of 2,4-D, NAA, BAP, IAA, IBA with 3% sucrose and 0.8% agar. Induced callus was immediately transferred to MS medium containing at different concentrations of phytohormones for shootlets and rootlets induction respectively. Results Sterilization treatment of 0.1% HgCl2 for 2-3 min and Bavistin 0.5% for 10-12 min showed the highest percentage of asepsis and survival rate. Maximum induction of callus was obtained from a combination of 2.0 mg/L 2,4-D and 0.5 mg/L NAA from leaf. Highest shootlets number (4.83±0.17) and length (3.8±0.16) cm were observed on full strength MS medium when fortified with BAP 4.0 mg/L and KIN 0.5 mg/L. Concerted efforts of BAP 2.0 mg/L and NAA 0.5 mg/L on full strength MS medium showed highest leaf number (6.77±0.94). In vitro raised shoots were allowed to root on different strengths of MS medium fortified with IAA and IBA at different concentrations. Experimentally, 3.0 mg/L IBA was enabled to induce maximum rootlets number (10.0±9.82) on full strength MS medium. Afterwards, regenerated shoots with well developed roots were successfully subjected to hardening process and were acclimatized. The survived plantlets showed 66.67% survival frequency without any morphological abnormality. Conclusions The results demonstrated that different explants were good source of callus induction, morphology analysis as well as indirect plantlets regeneration. PMID:24144129

76 FR 59764 - Self-Regulatory Organizations; NASDAQ OMX PHLX LLC; Notice of Filing and Immediate Effectiveness...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-27

... Change Relating to the Maximum Number of Quoters (``MNQ'') Permitted To Be Assigned in Equity Options...''),\\4\\ by establishing a higher maximum number of quoting participants (``Maximum Number of Quoters'' or...

Mercury concentrations in lean fish from the Western Mediterranean Sea: Dietary exposure and risk assessment in the population of the Balearic Islands.

PubMed

Llull, Rosa Maria; Garí, Mercè; Canals, Miquel; Rey-Maquieira, Teresa; Grimalt, Joan O

2017-10-01

The present study reports total mercury (THg) and methylmercury (MeHg) concentrations in 32 different lean fish species from the Western Mediterranean Sea, with a special focus on the Balearic Islands. The concentrations of THg ranged between 0.05mg/kg ww and 3.1mg/kg ww (mean 0.41mg/kg ww). A considerable number of the most frequently fish species consumed by the Spanish population exceed the maximum levels proposed by the European legislation when they originate from the Mediterranean Sea, such as dusky grouper (100% of the examined specimens), common dentex (65%), conger (45%), common sole (38%), hake (26%) and angler (15%), among others. The estimated weekly intakes (EWI) in children (7-12 years of age) and adults from the Spanish population (2.7µg/kg bw and 2.1µg/kg bw, respectively) for population only consuming Mediterranean fish were below the provisional tolerable weekly intake (PTWI) of THg established by EFSA in 2012, 4µg/kg bw. However, the equivalent estimations for methylmercury, involving PTWI of 1.3µg/kg bw, were two times higher in children and above 50% in adults. For hake, sole, angler and dusky grouper, the most frequently consumed fish, the estimated weekly intakes in both children and adults were below the maximum levels accepted. These intakes correspond to maximum potential estimations because fish from non-Mediterranean origin is often consumed by the Spanish population including the one from the Balearic Islands. Copyright © 2017 Elsevier Inc. All rights reserved.

Gaseous templates in ant nests.

PubMed

Cox, M D; Blanchard, G B

2000-05-21

We apply a diffusion model to the atmosphere of ant nests. With particular reference to carbon dioxide (CO2), we explore analytically and numerically the spatial and temporal patterns of brood- or worker-produced gases in nests. The maximum concentration within a typical one-chamber ant nest with approximately 200 ants can reach 12.5 times atmospheric concentration, reaching 95% of equilibrium concentrations within 15 min. Maximum concentration increases with increasing number of ants in the nest (or production rate of the gas), distance between the centre of the nest ants and the nest entrance, entrance length, wall thickness, and with decreasing entrance width, wall permeability and diffusion coefficient. The nest can be divided into three qualitatively distinct regions according to the shape of the gradient: a plateau of high concentration in the back half of the nest; an intermediate region of increasingly steep gradient towards the entrance; and a steep linear gradient in the entrance tunnel. These regions are robust to changes in gas concentrations, but vary with changes in nest architecture. The pattern of diffusing gases contains information about position and orientation relative to gas sources and sinks, and about colony state, including colony size, activity state and aspects of nest architecture. We discuss how this diffusion pattern may act as a "dynamic template", providing local cues which trigger behavioural acts appropriate to colony needs, which in turn may feed back to changes in the gas template. In particular, wall building occurs along lines of similar concentration for a variety of nest geometries; there is surprising convergence between the period of cycles of synchronously active ants and the time taken for CO2 levels to equilibrate; and the qualitatively distinct regions of the "dynamic template" correspond to regions occupied by different groups of ants.

Sewage sludge disintegration by high-pressure homogenization: a sludge disintegration model.

PubMed

Zhang, Yuxuan; Zhang, Panyue; Ma, Boqiang; Wu, Hao; Zhang, Sheng; Xu, Xin

2012-01-01

High-pressure homogenization (HPH) technology was applied as a pretreatment to disintegrate sewage sludge. The effects of homogenization pressure, homogenization cycle number, and total solid content on sludge disintegration were investigated. The sludge disintegration degree (DD(COD)), protein concentration, and polysaccharide concentration increased with the increase of homogenization pressure and homogenization cycle number, and decreased with the increase of sludge total solid (TS) content. The maximum DD(COD) of 43.94% was achieved at 80 MPa with four homogenization cycles for a 9.58 g/L TS sludge sample. A HPH sludge disintegration model of DD(COD) = kNaPb was established by multivariable linear regression to quantify the effects of homogenization parameters. The homogenization cycle exponent a and homogenization pressure exponent b were 0.4763 and 0.7324 respectively, showing that the effect of homogenization pressure (P) was more significant than that of homogenization cycle number (N). The value of the rate constant k decreased with the increase of sludge total solid content. The specific energy consumption increased with the increment of sludge disintegration efficiency. Lower specific energy consumption was required for higher total solid content sludge.

The maximum drag reduction asymptote

NASA Astrophysics Data System (ADS)

Choueiri, George H.; Hof, Bjorn

2015-11-01

Addition of long chain polymers is one of the most efficient ways to reduce the drag of turbulent flows. Already very low concentration of polymers can lead to a substantial drag and upon further increase of the concentration the drag reduces until it reaches an empirically found limit, the so called maximum drag reduction (MDR) asymptote, which is independent of the type of polymer used. We here carry out a detailed experimental study of the approach to this asymptote for pipe flow. Particular attention is paid to the recently observed state of elasto-inertial turbulence (EIT) which has been reported to occur in polymer solutions at sufficiently high shear. Our results show that upon the approach to MDR Newtonian turbulence becomes marginalized (hibernation) and eventually completely disappears and is replaced by EIT. In particular, spectra of high Reynolds number MDR flows are compared to flows at high shear rates in small diameter tubes where EIT is found at Re < 100. The research leading to these results has received funding from the People Programme (Marie Curie Actions) of the European Union's Seventh Framework Programme (FP7/2007-2013) under REA grant agreement n° [291734].

Amelioration and degradation of pressmud and bagasse wastes using vermitechnology.

PubMed

Bhat, Sartaj Ahmad; Singh, Jaswinder; Vig, Adarsh Pal

2017-11-01

This study evaluated the amelioration of pressmud (PM) and bagasse (BG) wastes by the vermiremediation process. The wastes were spiked with cattle dung (CD) in different concentrations to find out the best proportion supporting maximum earthworm growth and nutrients availability. The highest growth rate was observed in PMBG 50 (282.2mg/d/worm) feed mixture. Response surface design of earthworm growth parameters enumerated best concentration of wastes in CD with maximum value of 21.81% for earthworm number, 30.86% for earthworm weight, 27.09% for cocoons, 29.71% for hatchlings and 34.0% for hatchlings weight. Vermicomposting enhanced nutrient parameters like pH (6-8%), total kjeldahl nitrogen (19-48%), total phosphorus (9-67%), total calcium (13-111%), while decrease in total organic carbon (14-32%), electrical conductivity (21-30%), C:N ratio (36-51%), total potassium (9-19%) and total sodium (3-21%). Heavy metals in the final products were found to be under safe limits. SEM micrographs were more fragmented which indicated maturity and stability. Copyright © 2017 Elsevier Ltd. All rights reserved.

The biodegradation of cable oil components: impact of oil concentration, nutrient addition and bioaugmentation.

PubMed

Towell, Marcie G; Paton, Graeme I; Semple, Kirk T

2011-12-01

The effect of cable oil concentration, nutrient amendment and bioaugmentation on cable oil component biodegradation in a pristine agricultural soil was investigated. Biodegradation potential was evaluated over 21 d by measuring cumulative CO(2) respiration on a Micro-Oxymax respirometer and (14)C-phenyldodecane mineralisation using a (14)C-respirometric assay. Cable oil concentration had a significant effect upon oil biodegradation. Microbial respiratory activity increased with increasing cable oil concentration, whereas (14)C-phenydodecane mineralisation decreased. Bioaugmentation achieved the best cable oil biodegradation performance, resulting in increases in cumulative CO(2) respiration, and maximum rates and extents of (14)C-phenyldodecane mineralisation. Generally, nutrient amendment also enhanced cable oil biodegradation, but not to the extent that degrader amendment did. Cable oil biodegradation was a function of (i) cable oil concentration and (ii) catabolic ability of microbial populations. Bioaugmentation may enhance cable oil biodegradation, and is dependent upon composition, cell number and application of catabolic inocula to soil. Copyright © 2011 Elsevier Ltd. All rights reserved.

Reduction of Nicardipine-Related Phlebitis in Patients with Acute Stroke by Diluting Its Concentration.

PubMed

Kawada, Kei; Ohta, Tsuyoshi; Tanaka, Koudai; Miyamoto, Norifumi

2018-03-05

Nicardipine is frequently used in the treatment of hypertension for patients with acute stroke; however, its dosing is complicated by a high risk of phlebitis. In the present study, we examined whether restricting nicardipine concentration under a specific value could reduce the incidence of nicardipine-related phlebitis in patients with acute stroke. Intravenous nicardipine-related phlebitis was retrospectively analyzed. From July 2015, a simple proposition was made to dilute maximum intravenous nicardipine concentration to lower than 130 µg/mL. The maximum intravenous nicardipine concentration and the incidence of phlebitis were compared between patients treated from July 2014 to June 2015 (preproposition group) and patients treated from July 2015 to June 2016 (postproposition group). A total of 300 patients (preproposition group, 138; postproposition group, 162) were included. The postproposition group demonstrated significantly lower maximum intravenous nicardipine concentration (in µg/mL, 76.9, 47.6-104.5 versus 130.4, 69.8-230.8; P < .001) and incidence of phlebitis (9.9%, 16/162 vs. 30%, 42/138; P < .001) than the preproposition group. Multivariable logistic regression analysis revealed that the maximum intravenous nicardipine concentration lower than 130 µg/mL (odds ratio [OR] .15; 95% confidence interval [CI] .06-.35; P < .001) and National Institutes of Health Stroke Scale on admission (OR .95; 95% CI .91-.99; P = .007) were the statistically significant independent factors for phlebitis, which indicated the usefulness of the proposition to dilute maximum intravenous nicardipine concentration to lower than 130 µg/mL. The simple and appropriate proposition about nicardipine administration lowered maximum nicardipine concentration and reduced the incidence of nicardipine-related phlebitis in patients with acute stroke. Copyright © 2018 National Stroke Association. Published by Elsevier Inc. All rights reserved.

Modelling the maximum voluntary joint torque/angular velocity relationship in human movement.

PubMed

Yeadon, Maurice R; King, Mark A; Wilson, Cassie

2006-01-01

The force exerted by a muscle is a function of the activation level and the maximum (tetanic) muscle force. In "maximum" voluntary knee extensions muscle activation is lower for eccentric muscle velocities than for concentric velocities. The aim of this study was to model this "differential activation" in order to calculate the maximum voluntary knee extensor torque as a function of knee angular velocity. Torque data were collected on two subjects during maximal eccentric-concentric knee extensions using an isovelocity dynamometer with crank angular velocities ranging from 50 to 450 degrees s(-1). The theoretical tetanic torque/angular velocity relationship was modelled using a four parameter function comprising two rectangular hyperbolas while the activation/angular velocity relationship was modelled using a three parameter function that rose from submaximal activation for eccentric velocities to full activation for high concentric velocities. The product of these two functions gave a seven parameter function which was fitted to the joint torque/angular velocity data, giving unbiased root mean square differences of 1.9% and 3.3% of the maximum torques achieved. Differential activation accounts for the non-hyperbolic behaviour of the torque/angular velocity data for low concentric velocities. The maximum voluntary knee extensor torque that can be exerted may be modelled accurately as the product of functions defining the maximum torque and the maximum voluntary activation level. Failure to include differential activation considerations when modelling maximal movements will lead to errors in the estimation of joint torque in the eccentric phase and low velocity concentric phase.

Separation Process of Fine Coals by Ultrasonic Vibration Gas-Solid Fluidized Bed

PubMed Central

Wei, Hua; Xie, Weining

2017-01-01

Ultrasonic vibration gas-solid fluidized bed was proposed and introduced to separate fine coals (0.5–0.125 mm fraction). Several technological methods such as XRF, XRD, XPS, and EPMA were used to study the composition of heavy products to evaluate the separation effect. Results show that the ultrasonic vibration force field strengthens the particle separation process based on density when the vibration frequency is 35 kHz and the fluidization number is 1.8. The ash difference between the light and heavy products and the recovery of combustible material obtain the maximum values of 47.30% and 89.59%, respectively. The sulfur content of the heavy product reaches the maximum value of 6.78%. Chemical state analysis of sulfur shows that organic sulfur (-C-S-), sulfate-sulfur (-SO4), and pyrite-sulfur (-S2) are confirmed in the original coal and heavy product. Organic sulfur (-C-S-) is mainly concentrated in the light product, and pyrite-sulfur (-S2) is significantly enriched in the heavy product. The element composition, phase composition, backscatter imagery, and surface distribution of elements for heavy product show concentration of high-density minerals including pyrite, quartz, and kaolinite. Some harmful elements such as F, Pb, and As are also concentrated in the heavy product. PMID:28845160

In Vivo potassium-39 NMR spectra by the burg maximum-entropy method

NASA Astrophysics Data System (ADS)

Uchiyama, Takanori; Minamitani, Haruyuki

The Burg maximum-entropy method was applied to estimate 39K NMR spectra of mung bean root tips. The maximum-entropy spectra have as good a linearity between peak areas and potassium concentrations as those obtained by fast Fourier transform and give a better estimation of intracellular potassium concentrations. Therefore potassium uptake and loss processes of mung bean root tips are shown to be more clearly traced by the maximum-entropy method.

Using coral disease prevalence to assess the effects of concentrating tourism activities on offshore reefs in a tropical marine park.

PubMed

Lamb, Joleah B; Willis, Bette L

2011-10-01

Concentrating tourism activities can be an effective way to closely manage high-use parks and minimize the extent of the effects of visitors on plants and animals, although considerable investment in permanent tourism facilities may be required. On coral reefs, a variety of human-related disturbances have been associated with elevated levels of coral disease, but the effects of reef-based tourist facilities (e.g., permanent offshore visitor platforms) on coral health have not been assessed. In partnership with reef managers and the tourism industry, we tested the effectiveness of concentrating tourism activities as a strategy for managing tourism on coral reefs. We compared prevalence of brown band disease, white syndromes, black band disease, skeletal eroding band, and growth anomalies among reefs with and without permanent tourism platforms within the Great Barrier Reef Marine Park. Coral diseases were 15 times more prevalent at reefs with offshore tourism platforms than at nearby reefs without platforms. The maximum prevalence and maximum number of cases of each disease type were recorded at reefs with permanently moored tourism platforms. Diseases affected 10 coral genera from 7 families at reefs with platforms and 4 coral genera from 3 families at reefs without platforms. The greatest number of disease cases occurred within the spatially dominant acroporid corals, which exhibited 18-fold greater disease prevalence at reefs with platforms than at reefs without platforms. Neither the percent cover of acroporids nor overall coral cover differed significantly between reefs with and without platforms, which suggests that neither factor was responsible for the elevated levels of disease. Identifying how tourism activities and platforms facilitate coral disease in marine parks will help ensure ongoing conservation of coral assemblages and tourism. ©2011 Society for Conservation Biology.

Polymer-surfactant complex formation and its effect on turbulent wall shear stress.

PubMed

Suksamranchit, Siriluck; Sirivat, Anuvat; Jamieson, Alexander M

2006-02-01

Turbulent drag reduction in Couette flow was investigated in terms of a decrease in wall shear stress for aqueous solutions of a nonionic polymer, poly(ethylene oxide) (PEO), a cationic surfactant, hexadecyltrimethylammonium chloride (HTAC), and their mixtures. Consistent with literature data, drag reduction was observed for PEO solutions above a critical molecular weight, 0.91 x 10(5) < Mc < 3.04 x 10(5) g/mol. Maximum drag reduction occurred at an optimum concentration, c(PEO)*, which scales inversely with molecular weight, and the % maximum drag reduction increases with molecular weight. For aqueous HTAC solutions, wall shear stress decreased with increasing HTAC concentration and leveled off at an optimum concentration, c(HTAC)*, comparable to the critical micelle concentration. For HTAC/PEO mixtures, the critical PEO molecular weight for drag reduction decreases, interpreted as due to an increase in hydrodynamic volume because of binding of HTAC micelles to PEO. Consistent with this interpretation, at fixed PEO concentration, maximum drag reduction was observed at an optimum HTAC concentration, c(HTAC/PEO)*, comparable to the maximum binding concentration, MBC. Also, with HTAC concentration fixed at the MBC, the optimum PEO concentration for drag reduction, c(PEO/HTAC)*, decreases relative to that, c(PEO)*, in the absence of HTAC.

Diffusion via space discretization method to study the concentration dependence of self-diffusivity under confinement

NASA Astrophysics Data System (ADS)

Sant, Marco; Papadopoulos, George K.; Theodorou, Doros N.

2010-04-01

The concentration dependence of self-diffusivity is investigated by means of a novel method, extending our previously developed second-order Markov process model to periodic media. Introducing the concept of minimum-crossing surface, we obtain a unique decomposition of the self-diffusion coefficient into two parameters with specific physical meanings. Two case studies showing a maximum in self-diffusivity as a function of concentration are investigated, along with two cases where such a maximum cannot be present. Subsequently, the method is applied to the large cavity pore network of the ITQ-1 (Mobil tWenty tWo, MWW) zeolite for methane (displaying a maximum in self-diffusivity) and carbon dioxide (no maximum), explaining the diffusivity trend on the basis of the evolution of the model parameters as a function of concentration.

Consolidation in the Dialysis Industry, Patient Choice, and Local Market Competition.

PubMed

Erickson, Kevin F; Zheng, Yuanchao; Winkelmayer, Wolfgang C; Ho, Vivian; Bhattacharya, Jay; Chertow, Glenn M

2017-03-07

The Medicare program insures >80% of patients with ESRD in the United States. An emphasis on reducing outpatient dialysis costs has motivated consolidation among dialysis providers, with two for-profit corporations now providing dialysis for >70% of patients. It is unknown whether industry consolidation has affected patients' ability to choose among competing dialysis providers. We identified patients receiving in-center hemodialysis at the start of 2001 and 2011 from the national ESRD registry and ascertained dialysis facility ownership. For each hospital service area, we determined the maximum distance within which 90% of patients traveled to receive dialysis in 2001. We compared the numbers of competing dialysis providers within that same distance between 2001 and 2011. Additionally, we examined the Herfindahl-Hirschman Index, a metric of market concentration ranging from near zero (perfect competition) to one (monopoly) for each hospital service area. Between 2001 and 2011, the number of different uniquely owned competing providers decreased 8%. However, increased facility entry into markets to meet rising demand for care offset the effect of provider consolidation on the number of choices available to patients. The number of dialysis facilities in the United States increased by 54%, and patients experienced an average 10% increase in the number of competing proximate facilities from which they could choose to receive dialysis ( P <0.001). Local markets were highly concentrated in both 2001 and 2011 (mean Herfindahl-Hirschman Index =0.46; SD=0.2 for both years), but overall market concentration did not materially change. In summary, a decade of consolidation in the United States dialysis industry did not (on average) limit patient choice or result in more concentrated local markets. However, because dialysis markets remained highly concentrated, it will be important to understand whether market competition affects prices paid by private insurers, access to dialysis care, quality of care, and associated health outcomes. Copyright © 2017 by the American Society of Nephrology.

Consolidation in the Dialysis Industry, Patient Choice, and Local Market Competition

PubMed Central

Zheng, Yuanchao; Winkelmayer, Wolfgang C.; Bhattacharya, Jay; Chertow, Glenn M.

2017-01-01

The Medicare program insures >80% of patients with ESRD in the United States. An emphasis on reducing outpatient dialysis costs has motivated consolidation among dialysis providers, with two for-profit corporations now providing dialysis for >70% of patients. It is unknown whether industry consolidation has affected patients’ ability to choose among competing dialysis providers. We identified patients receiving in-center hemodialysis at the start of 2001 and 2011 from the national ESRD registry and ascertained dialysis facility ownership. For each hospital service area, we determined the maximum distance within which 90% of patients traveled to receive dialysis in 2001. We compared the numbers of competing dialysis providers within that same distance between 2001 and 2011. Additionally, we examined the Herfindahl–Hirschman Index, a metric of market concentration ranging from near zero (perfect competition) to one (monopoly) for each hospital service area. Between 2001 and 2011, the number of different uniquely owned competing providers decreased 8%. However, increased facility entry into markets to meet rising demand for care offset the effect of provider consolidation on the number of choices available to patients. The number of dialysis facilities in the United States increased by 54%, and patients experienced an average 10% increase in the number of competing proximate facilities from which they could choose to receive dialysis (P<0.001). Local markets were highly concentrated in both 2001 and 2011 (mean Herfindahl–Hirschman Index =0.46; SD=0.2 for both years), but overall market concentration did not materially change. In summary, a decade of consolidation in the United States dialysis industry did not (on average) limit patient choice or result in more concentrated local markets. However, because dialysis markets remained highly concentrated, it will be important to understand whether market competition affects prices paid by private insurers, access to dialysis care, quality of care, and associated health outcomes. PMID:27831510

Artefactual serum hyperkalaemia and hypercalcaemia in essential thrombocythaemia

PubMed Central

Howard, M; Ashwell, S; Bond, L; Holbrook, I

2000-01-01

Aim—To investigate possible abnormalities of serum potassium and calcium levels in patients with essential thrombocythaemia and significant thrombocytosis. Methods—24 cases of essential thrombocythaemia with significant thrombocytosis (platelet count > 700 x 109/litre) had serum potassium and calcium estimations performed at the time of maximum thrombocytosis before treatment, and at the time of low platelet count after treatment with cytoreductive drugs. Selected patients were further investigated with plasma sampling and estimation of ionised calcium and parathyroid hormone. Results—At the time of maximum thrombocytosis six patients had serum hyperkalaemia (> 5.5 mmol/litre) and five had serum hypercalcaemia (> 2.6 mmol/litre). Following treatment and reduction of the platelet count, hyperkalaemia resolved in all cases and hypercalcaemia in four of the five cases. Mean serum potassium and calcium concentrations were raised (p < 0.0001) at maximum thrombocytosis compared with the values when the platelet count was low. Serum potassium and calcium values were significantly correlated at all stages. Measurements on plasma consistently corrected the hyperkalaemia but not the hypercalcaemia. Serum hypercalcaemia was associated with raised ionised calcium and normal parathyroid hormone concentrations. Conclusions—Essential thrombocythaemia with significant thrombocytosis is associated with serum hyperkalaemia and hypercalcaemia. The probable mechanism of hypercalcaemia is the secretion of calcium in vitro from an excessive number of abnormally activated platelets. It is thus likely that the hypercalcaemia is an artefact, as is the hyperkalaemia. Key Words: thrombocythaemia • hypercalcaemia • hyperkalaemia PMID:10767824

The influence of screening of the polyion electrostatic potential on the counterion dynamics in polyelectrolyte solutions

NASA Astrophysics Data System (ADS)

Schipper, F. J. M.; Hollander, J. G.; Leyte, J. C.

1998-10-01

The self-diffusion coefficient of tetra-methylammonium counterion in solutions of polymethacrylic acid in 0953-8984/10/41/004/img1 has been measured over a broad polyion concentration range at a constant degree of neutralization and at different ratios of added monovalent or bivalent salt to polyions. A maximum counterion self-diffusion coefficient was observed as a function of polyion concentration. The value of the self-diffusion coefficient at the maximum did not depend on the valency of the added salt. The maximum was found at lower polymer concentrations and with a higher value, when the ratio of added salt to polyions was increased, as predicted by the Poisson-Boltzmann-Smoluchowski equation in the cylindrical cell model for polyelectrolytes. At higher polyion concentrations a maximum counterion self-diffusion coefficient against the ratio of added salt and polyions was observed, which has not been reported before. Upon increasing this ratio the electrostatic potential of the polyelectrolyte gets screened, leading to an increase of the counterion self-diffusion coefficient. Concentration effects of the added salt on the other hand ultimately lead to a decrease of the counterion self-diffusion coefficient, which explains the occurrence of a maximum.

A comparison of in-cloud HCl concentrations from the NASA/MSFC MDM to measurements for the space shuttle launch

NASA Technical Reports Server (NTRS)

Glasser, M. E.

1981-01-01

The Multilevel Diffusion Model (MDM) Version 5 was modified to include features of more recent versions. The MDM was used to predict in-cloud HCl concentrations for the April 12 launch of the space Shuttle (STS-1). The maximum centerline predictions were compared with measurements of maximum gaseous HCl obtained from aircraft passes through two segments of the fragmented shuttle ground cloud. The model over-predicted the maximum values for gaseous HCl in the lower cloud segment and portrayed the same rate of decay with time as the observed values. However, the decay with time of HCl maximum predicted by the MDM was more rapid than the observed decay for the higher cloud segment, causing the model to under-predict concentrations which were measured late in the life of the cloud. The causes of the tendency for the MDM to be conservative in over-estimating the HCl concentrations in the one case while tending to under-predict concentrations in the other case are discussed.

The relationship between the deep-level structure in crust and brewing of strong earthquakes in Xingtai area

NASA Astrophysics Data System (ADS)

Xiao, Lan-Xi; Zhu, Yuan-Qing; Zhang, Shao-Quan; Liu, Xu; Guo, Yu

1999-11-01

In this paper, crust medium is treated as Maxwell medium, and crust model includes hard inclusion, soft inclusion, deep-level fault. The stress concentration and its evolution with time are obtained by using three-dimensional finite element method and differential method. The conclusions are draw as follows: (1) The average stress concentration and maximum shear stress concentration caused by non-heterogeneous of crust are very high in hard inclusion and around the deep fault. With the time passing by, the concentration of average stress in the model gradually trends to uniform. At the same time, the concentration of maximum shear stress in hard inclusion increases gradually. This character is favorable to transfer shear strain energy from soft inclusion to hard inclusion. (2) When the upper mantle beneath the inclusion upheave at a certain velocity of 1 cm/a, the changes of average stress concentration with time become complex, and the boundary of the hard and soft inclusion become unconspicuous, but the maximum shear stress concentration increases much more in the hard inclusion with time at a higher velocity. This feature make for transformation of energy from the soft inclusion to the hard inclusion. (3) The changes of average stress concentration and maximum shear stress concentration with time around the deep-level fault result in further accumulation of maximum shear stress concentration and finally cause the deep-level fault instable and accelerated creep along fault direction. (4) The changes of vertical displacement on the surface of the model, which is caused by the accelerated creep of the deep-level fault, is similar to that of the observation data before Xingtai strong earthquake.

Fluorescent biological aerosol particles measured with the Waveband Integrated Bioaerosol Sensor WIBS-4: laboratory tests combined with a one year field study

NASA Astrophysics Data System (ADS)

Toprak, E.; Schnaiter, M.

2013-01-01

In this paper bioaerosol measurements conducted with the Waveband Integrated Bioaerosol Sensor mark 4 (WIBS-4) are presented. The measurements comprise aerosol chamber characterization experiments and a one-year ambient measurement period at a semi-rural site in South Western Germany. This study aims to investigate the sensitivity of WIBS-4 to biological and non-biological aerosols and detection of biological particles in the ambient aerosol. Several types of biological and non-biological aerosol samples, including fungal spores, bacteria, mineral dust, ammonium sulphate, combustion soot, and fluorescent polystyrene spheres, were analyzed by WIBS-4 in the laboratory. The results confirm the sensitivity of the ultraviolet light-induced fluorescence (UV-LIF) method to biological fluorophores and show the good discrimination capabilities of the two excitation wavelengths/detection wavebands method applied in WIBS-4. However, a weak cross-sensitivity to non-biological fluorescent interferers remains and is discussed in this paper. All the laboratory studies have been undertaken in order to prepare WIBS-4 for ambient aerosol measurements. According to the one-year ambient aerosol study, number concentration of fluorescent biological aerosol particles (FBAP) show strong seasonal and diurnal variability. The highest number concentration of FBAP was measured during the summer term and decreased towards the winter period when colder and drier conditions prevail. Diurnal FBAP concentrations start to increase after sunset and reach maximum values during the late night and early morning hours. On the other hand, the total aerosol number concentration was almost always higher during daytime than during nighttime and a sharp decrease after sunset was observed. There was no correlation observed between the FBAP concentration and the meteorological parameters temperature, precipitation, wind direction and wind speed. However, a clear correlation was identified between the FBAP number concentration and the relative humidity. Humidity-controlled release mechanisms of some fungal spore species are discussed as a possible explanation.

Glyphosate and AMPA, "pseudo-persistent" pollutants under real-world agricultural management practices in the Mesopotamic Pampas agroecosystem, Argentina.

PubMed

Primost, Jezabel E; Marino, Damián J G; Aparicio, Virginia C; Costa, José Luis; Carriquiriborde, Pedro

2017-10-01

In the Pampas, public concern has strongly risen because of the intensive use of glyphosate for weed control and fallow associated with biotech crops. The present study was aimed to evaluate the occurrence and concentration of the herbicide and its main metabolite (AMPA) in soil and other environmental compartments of the mentioned agroecosystem, including groundwater, in relation to real-world agricultural management practices in the region. Occurrence was almost ubiquitous in solid matrices (83-100%) with maximum concentrations among the higher reported in the world (soil: 8105 and 38939; sediment: 3294 and 7219; suspended particulate matter (SPM): 584 and 475 μg/kg of glyphosate and AMPA). Lower detection frequency was observed in surface water (27-55%) with maximum concentrations in whole water of 1.80 and 1.90 μg/L of glyphosate and AMPA, indicating that SPM analysis would be more sensitive for detection in the aquatic ecosystem. No detectable concentrations of glyphosate or AMPA were observed in groundwater. Glyphosate soil concentrations were better correlated with the total cumulative dose and total number of applications than the last spraying event dose, and an increment of 1 mg glyphosate/kg soil every 5 spraying events was estimated. Findings allow to infer that, under current practices, application rates are higher than dissipation rates. Hence, glyphosate and AMPA should be considered "pseudo-persistent" pollutants and a revisions of management procedures, monitoring programs, and ecological risk for soil and sediments should be also recommended. Copyright © 2017 Elsevier Ltd. All rights reserved.

Host-specific variation in infection by toxigenic fungi and contamination by mycotoxins in pearl millet and corn.

PubMed

Wilson, J P; Jurjevic, Z; Hanna, W W; Wilson, D M; Potter, T L; Coy, A E

2006-02-01

Pearl millet is widely consumed in regions of Africa and Asia, and is increasingly being grown as an alternative grain in drought-prone regions of the United States. Pearl millet and corn were grown in dryland conditions at Tifton, Georgia, USA and grains were compared for pre-harvest infection by potentially toxigenic fungi and contamination by mycotoxins. Corn hybrids Agripro 9909 and Pioneer 3146, and pearl millet Tifgrain 102 were grown in 2000 and 2001; pearl millet HGM 100 was included in the test in 2001. Hybrids were sown on multiple planting dates in each year to induce variation in flowering time. Host species differed in the frequency of isolation of potentially toxigenic fungal species in both years. Across years, corn hybrids were more prone to infection by Aspergillus flavus Link (maximum isolation frequency = 8.8%) and Fusarium moniliforme Sheldon sensu lato (maximum isolation frequency = 72.8%), with corresponding greater concentrations of aflatoxins (maximum concentration = 204.9 microg kg(-1)) and fumonisins (maximum concentration = 34,039 microg kg(-1)). Pearl millet was more prone to infection by F. semitectum Berk. & Ravenel (maximum isolation = 74.2%) and F. chlamydosporum Wollenweb & Reinking (maximum isolation = 33.0%), and contamination by moniliformin (maximum contamination = 92.1 microg kg(-1)). Beauvericin (maximum concentration = 414.6 microg kg(-1)) was present in both hosts. Planting date of corn affected aflatoxin and beauvericin contamination in 2000, and fumonisin concentration in 2001. The observed differences in mycotoxin contamination of the grains, which are likely due to host-specific differences in susceptibility to pre-harvest mycoflora, may affect food safety when the crops are grown under stress conditions.

Water-quality assessment of the Delmarva Peninsula, Delaware, Maryland, and Virginia; effects of agricultural activities on, and distribution of, nitrate and other inorganic constituents in the surficial aquifer

USGS Publications Warehouse

Hamilton, P.A.; Denver, J.M.; Phillips, P.J.; Shedlock, R.J.

1993-01-01

Agricultural applications of inorganic fertilizers and manure have changed the natural chemical com- position of water in the surficial aquifer through- out the Delmarva Peninsula. Nitrate, derived from nitrification of ammonia in inorganic fertilizers and manure, is the dominant anion in agricultural areas. Concentrations of nitrate in 185 water samples collected in agricultural areas ranged from 0.4 to 48 mg/L as nitrogen, with a median concen- tration of 8.2 mg/L as nitrogen. Nitrate concen- trations exceeded the U.S. Environmental Protection Agency's maximum contaminant level for drinking water of 10 mg/L as nitrogen in about 33% of the 185 water samples. Groundwater affected by agricultural activities contains significantly higher concentrations of dissolved constituents than does natural groundwater. Concentrations of calcium and magnesium are higher because of liming of soils, and concentrations of potassium and chloride are higher because of applications of potash, a supple- ment to the nitrogen-based fertilizers. Alkalinity concentrations commonly are decreased because the bicarbonate ion is consumed in buffering reactions with acid that is produced during nitrification. Effects of agricultural activities on groundwater quality are not limited to the near-surface parts of the aquifer underlying farm fields. Elevated concentrations are common in aerobic water at or near the base of the aquifer, 80 to 100 ft below land surface. The median concentration of nitrate in water beneath agricultural areas collected from 24 wells deeper than 80 ft below land surface was 8.5 mg/L as nitrogen, and concentrations in 9 of these water samples exceeded the maximum contaminant level. Regional variations in concentrations of nitrate and other agriculture related constituents in the surficial aquifer in the Delmarva Peninsula depend on a number of factors that include geomorphology, geology, soils, land use, and groundwater-flow patterns. (USGS)

Interactive Effects of Growth Regulators, Carbon Sources, pH on Plant Regeneration and Assessment of Genetic Fidelity Using Single Primer Amplification Reaction (SPARS) Techniques in Withania somnifera L.

PubMed

Fatima, Nigar; Ahmad, Naseem; Ahmad, Iqbal; Anis, Mohammad

2015-09-01

An improved and methodical in vitro shoot morphogenic approach through axillary bud multiplication was established in a drug yielding plant, Withania somnifera L. Effects of plant growth regulators [6-benzyladenine (BA), kinetin (Kin), 2-isopentenyladenine (2iP), and thidiazuron (TDZ)] either singly or in combination with α-napthalene acetic acid (NAA), indole-3-butyric acid (IBA), and indole-3-acetic acid (IAA) in Murashige and Skoog (MS) medium were tested. The highest regeneration frequency (90 %) with optimum number of shoots (32 ± 0.00)/explant were obtained on MS medium fortified with 2.5 μM 6-benzyladenine (BA) and 0.5 μM NAA and 30 g/l sucrose at pH 5.8. Among the tried TDZ concentrations, 0.5 μM resulted in maximum number of shoots (20.4 ± 0.40)/explant after 4 weeks of exposure. The proliferating shoot cultures established by repeated subculturing of the mother explants on the hormone-free medium produced the highest shoot number (29.4 ± 0.40) with shoot length (6.80 ± 0.12 cm)/explant at fourth subculture passage, which a decline in shoot proliferation was recorded. Different concentrations of NAA were tested for ex vitro rooting of microshoots. The maximum percentage of rooting 100 % with maximum roots (18.3 ± 0.1) was achieved in soilrite when basal portion of the microshoots were treated with 200 μM (NAA) for 15 min per shoot. The plantlets went through hardening phase in a growth chamber, prior to ex vitro transfer. The PCR-based single primer amplification reaction (SPAR) methods which include random amplified polymorphic DNA (RAPD) and direct amplification of minisatellite DNA (DAMD) markers has been used for assessment of genetic stability of micropropagated plantlets. No variation was observed in DNA fingerprinting patterns among the micropropagated and the donor plants illustrating their genetic uniformity.

Effects of non-unity Lewis numbers in diffusion flames

NASA Technical Reports Server (NTRS)

Linan, A.; Orlandi, P.; Verzicco, R.; Higuera, F. J.

1994-01-01

The purpose of this work is to carry out direct numerical simulations of diffusion controlled combustion with non-unity Lewis numbers for the reactants and products, thus accounting for the differential diffusion effects of the temperature and concentration fields. We use a formulation based on combining the conservation equations in a way to eliminate the reaction terms similar to the method used by Burke and Schumann (1928) for unity Lewis numbers. We present calculations for an axisymmetric fuel jet and for a planar, time evolving mixing layer, leaving out the effects of thermal expansion and variations of the transport coefficients due to the heat release. Our results show that the front of the flame shifts toward the fuel or oxygen sides owing to the effect of the differential diffusion and that the location of maximum temperature may not coincide with the flame. The dependence of the distribution of the reaction products on their Lewis number has been investigated.

Emissions from an International Airport Increase Particle Number Concentrations 4-fold at 10 km Downwind

PubMed Central

2014-01-01

We measured the spatial pattern of particle number (PN) concentrations downwind from the Los Angeles International Airport (LAX) with an instrumented vehicle that enabled us to cover larger areas than allowed by traditional stationary measurements. LAX emissions adversely impacted air quality much farther than reported in previous airport studies. We measured at least a 2-fold increase in PN concentrations over unimpacted baseline PN concentrations during most hours of the day in an area of about 60 km2 that extended to 16 km (10 miles) downwind and a 4- to 5-fold increase to 8–10 km (5–6 miles) downwind. Locations of maximum PN concentrations were aligned to eastern, downwind jet trajectories during prevailing westerly winds and to 8 km downwind concentrations exceeded 75 000 particles/cm3, more than the average freeway PN concentration in Los Angeles. During infrequent northerly winds, the impact area remained large but shifted to south of the airport. The freeway length that would cause an impact equivalent to that measured in this study (i.e., PN concentration increases weighted by the area impacted) was estimated to be 280–790 km. The total freeway length in Los Angeles is 1500 km. These results suggest that airport emissions are a major source of PN in Los Angeles that are of the same general magnitude as the entire urban freeway network. They also indicate that the air quality impact areas of major airports may have been seriously underestimated. PMID:24871496

Occurrence of pharmaceutical compounds in wastewater process streams in Dublin, Ireland.

PubMed

Lacey, Clair; Basha, Shaik; Morrissey, Anne; Tobin, John M

2012-01-01

The aim of this work is to establish baseline levels of pharmaceuticals in three wastewater treatment plant (WWTP) streams in the greater Dublin region to assess the removal efficiency of the selected WWTPs and to investigate the existence of any seasonal variability. Twenty compounds including several classes of antibiotics, acidic and basic pharmaceuticals, and prescribed medications were selected for investigation using a combination of membrane filtration, solid phase extraction (SPE) cleanup, and liquid chromatography-electrospray ionization tandem mass spectrometry. Fourteen of the selected compounds were found in the samples. Increased effluent concentrations, compared to influent concentrations, for a number of compounds (carbamazepine, clotrimazole, propranolol, nimesulide, furosemide, mefenamic acid, diclofenac, metoprolol, and gemfibrozil) were observed. The detected concentrations were generally below toxicity levels and based on current knowledge are unlikely to pose any threat to aquatic species. Mefenamic acid concentrations detected in both Leixlip and Swords effluents may potentially exert ecotoxicological effects with maximum risk quotients (i.e., ratio of predicted exposure concentration to predicted no effect concentration) of 4.04 and 1.33, respectively.

Heat transfer and pressure drop characteristics of a plate heat exchanger using water based Al2O3 nanofluid for 30° and 60° chevron angles

NASA Astrophysics Data System (ADS)

Elias, M. M.; Saidur, R.; Ben-Mansour, R.; Hepbasli, A.; Rahim, N. A.; Jesbains, K.

2018-04-01

Nanofluid is a new class of engineering fluid that has good heat transfer characteristics which is essential to increase the heat transfer performance in various engineering applications such as heat exchangers and cooling of electronics. In this study, experiments were conducted to compare the heat transfer performance and pressure drop characteristics in a plate heat exchanger (PHE) for 30° and 60° chevron angles using water based Al2O3 nanofluid at the concentrations from 0 to 0.5 vol.% for different Reynolds numbers. The thermo-physical properties has been determined and presented in this paper. At 0.5 vol% concentration, the maximum heat transfer coefficient, the overall heat transfer coefficient and the heat transfer rate for 60° chevron angle have attained a higher percentage of 15.14%, 7.8% and 15.4%, respectively in comparison with the base fluid. Consequently, when the volume concentration or Reynolds number increases, the heat transfer coefficient and the overall heat transfer coefficient as well as the heat transfer rate of the PHE (Plate Heat Exchangers) increases respectively. Similarly, the pressure drop increases with the volume concentration. 60° chevron angle showed better performance in comparison with 30° chevron angle.

40 CFR 463.34 - New source performance standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... pollutant concentrations: Subpart C [Finishing water] Concentration used to calculate NSPS Pollutant or pollutant property Maximum for any 1 day (mg/l) Maximum for monthly average (mg/l) TSS 130 37 pH (1) (1) 1...

Investigation of ionic conduction in PEO-PVDF based blend polymer electrolytes

NASA Astrophysics Data System (ADS)

Patla, Subir Kumar; Ray, Ruma; Asokan, K.; Karmakar, Sanat

2018-03-01

We investigate the effect of blend host polymer on solid polymer electrolyte (SPE) films doped with ammonium iodide (NH4I) salt using a variety of experimental techniques. Structural studies on the composite SPEs show that the blending of Poly(ethylene oxide) (PEO)-Poly(vinylidene fluoride) (PVDF) polymers in a suitable ratio enhances the amorphous fraction of the polymer matrix and facilitates fast ion conduction through it. We observe that the addition of a small amount of PVDF in the PEO host polymer enhances the ion - polymer interaction leading to more ion dissociation. As a result, the effective number of mobile charge carriers within the polymer matrix increases. Systematic investigation in these blend SPEs shows that the maximum conductivity (1.01 × 10-3 S/cm) is obtained for PEO - rich (80 wt. % PEO, 20 wt. % PVDF) composites at 35 wt. % NH4I concentration at room temperature. Interestingly, at higher salt concentrations (above 35 wt. %), the conductivity is found to decrease in this system. The reduction of conductivity at higher salt concentrations is the consequence of decrease in the carrier concentration due to the formation of an ion pair and ion aggregates. PVDF-rich compositions (20 wt. % PEO and 80 wt. % PVDF), on the other hand, show a very complex porous microstructure. We also observe a much lower ionic conductivity (maximum ˜ 10-6 S/cm at 15 wt. % salt) in these composite systems relative to PEO-rich composites.

From hygroscopic aerosols to cloud droplets: The HygrA-CD campaign in the Athens basin - An overview.

PubMed

Papayannis, A; Argyrouli, A; Bougiatioti, A; Remoundaki, E; Vratolis, S; Nenes, A; Solomos, S; Komppula, M; Giannakaki, E; Kalogiros, J; Banks, R; Eleftheriadis, K; Mantas, E; Diapouli, E; Tzanis, C G; Kazadzis, S; Binietoglou, I; Labzovskii, L; Vande Hey, J; Zerefos, C S

2017-01-01

The international experimental campaign Hygroscopic Aerosols to Cloud Droplets (HygrA-CD), organized in the Greater Athens Area (GAA), Greece from 15 May to 22 June 2014, aimed to study the physico-chemical properties of aerosols and their impact on the formation of clouds in the convective Planetary Boundary Layer (PBL). We found that under continental (W-NW-N) and Etesian (NE) synoptic wind flow and with a deep moist PBL (~2-2.5km height), mixed hygroscopic (anthropogenic, biomass burning and marine) particles arrive over the GAA, and contribute to the formation of convective non-precipitating PBL clouds (of ~16-20μm mean diameter) with vertical extent up to 500m. Under these conditions, high updraft velocities (1-2ms -1 ) and cloud condensation nuclei (CCN) concentrations (~2000cm -3 at 1% supersaturation), generated clouds with an estimated cloud droplet number of ~600cm -3 . Under Saharan wind flow conditions (S-SW) a shallow PBL (<1-1.2km height) develops, leading to much higher CCN concentrations (~3500-5000cm -3 at 1% supersaturation) near the ground; updraft velocities, however, were significantly lower, with an estimated maximum cloud droplet number of ~200cm -3 and without observed significant PBL cloud formation. The largest contribution to cloud droplet number variance is attributed to the updraft velocity variability, followed by variances in aerosol number concentration. Copyright © 2016 Elsevier B.V. All rights reserved.

Reconnaissance-level assessment of water and bottom-sediment quality, including pesticides and mercury, in Yankton Sioux Tribe wetlands, Charles Mix County, South Dakota, June-July 2005

USGS Publications Warehouse

Schaap, Bryan D.; Bartholomay, Roy C.

2006-01-01

During June and July 2005, water and bottom-sediment samples were collected from selected Yankton Sioux Tribe wetlands within the historic Reservation area of eastern Charles Mix County as part of a reconnaissance-level assessment by the U.S. Geological Survey and Yankton Sioux Tribe. The water samples were analyzed for pesticides and mercury species. In addition, the water samples were analyzed for physical properties and chemical constituents that might help further characterize the water quality of the wetlands. The bottom-sediment samples were analyzed for mercury species. During June 2005, water samples were collected from 19 wetlands and were analyzed for 61 widely used pesticide compounds. Many pesticides were not detected in any of the water samples and many others were detected only at low concentrations in a few of the samples. Thirteen pesticides were detected in water samples from at least one of the wetlands. Atrazine and de-ethyl atrazine were detected at each of the 19 wetlands. The minimum, maximum, and median dissolved atrazine concentrations were 0.056, 0.567, and 0.151 microgram per liter (?g/L), respectively. Four pesticides (alachlor, carbaryl, chlorpyrifos, and dicamba) were detected in only one wetland each. The number of pesticides detected in any of the 19 wetlands ranged from 3 to 8, with a median of 6. In addition to the results for this study, recent previous studies have frequently found atrazine in Lake Andes and the Missouri River, but none of the atrazine concentrations have been greater than 3 ?g/L, the U.S. Environmental Protection Agency's Maximum Contaminant Level for atrazine in drinking water. During June and July 2005, water and bottom-sediment samples were collected from 10 wetlands. Water samples from each of the wetlands were analyzed for major ions, organic carbon, and mercury species, and bottom-sediment samples were analyzed for mercury species. For the whole-water samples, the total mercury concentrations ranged from 1.11 to 29.65 nanograms per liter (ng/L), with a median of 10.56 ng/L. The methylmercury concentrations ranged from 0.45 to 14.03 ng/L, with a median of 2.28 ng/L. For the bottom-sediment samples, the total mercury concentration ranged from 21.3 to 74.6 nanograms per gram (ng/g), with a median of 54.2 ng/g. The methylmercury concentrations ranged from <0.11 to 2.04 ng/g, with a median of 0.78 ng/g. The total mercury concentrations in the water samples were all much less than 2 ?g/L (2,000 ng/L), the U.S. Environmental Protection Agency's Maximum Contaminant Level for mercury in drinking water. However, water samples from four of the wetlands had concentrations larger than 0.012 ?g/L (12 ng/L), the State of South Dakota's chronic standard for surface waters, including wetlands. Maximum methylmercury concentrations for this study are larger than reported concentrations for wetlands in North Dakota and concentrations reported for the Cheyenne River Indian Reservation in South Dakota.

Comparison of the Force-, Velocity- and Power-Time Curves Between the Concentric-Only and Eccentric-Concentric Bench Press Exercises.

PubMed

Pérez-Castilla, Alejandro; Comfort, Paul; McMahon, John J; Pestaña-Melero, Francisco Luis; García-Ramos, Amador

2018-01-17

The aim of this study was to compare the temporal and mechanical variables between the concentric-only and eccentric-concentric bench press (BP) variants. Twenty-one men (age: 22.0±4.2 years, body mass: 73.4±7.7 kg, height: 177.2±8.0 cm; one-repetition maximum [1RM]: 1.12±0.12 kg⋅kg) were evaluated during the concentric-only and eccentric-concentric BP variants using 80% 1RM. Temporal (concentric phase duration, propulsive phase duration, and time to reach the maximum values of force, velocity, and power) and mechanical variables (force, velocity, and power), determined using a linear velocity transducer, were compared between both BP variants. All temporal variables were significantly lower during the eccentric-concentric BP compared to the concentric-only BP (P < 0.05; effect size [ES] range: 0.80-2.52). Maximum force as well as the mean values of velocity and power were significantly higher for the eccentric-concentric BP compared to the concentric-only BP (all P < 0.001; ES range: 2.87-3.58). However, trivial to small differences between both BP variants were observed for mean force (ES: 0.00-0.36) as well as for maximum velocity (ES: 0.40) and power (ES: 0.41). The stretch-shortening cycle (i.e., eccentric-concentric BP) mainly enhanced force production at the early portion of the concentric phase, but this potentiation effect gradually reduced over the latter part of the movement. Finally, force was higher for the concentric-only BP during 49% of the concentric phase duration. These results suggest that both BP variants should be included during resistance training programs in order to optimize force output at different points of the concentric phase.

Ground-water quality in the Central High Plains Aquifer, Colorado, Kansas, New Mexico, Oklahoma, and Texas, 1999

USGS Publications Warehouse

Becker, Mark F.; Bruce, Breton W.; Pope, Larry M.; Andrews, William J.

2002-01-01

A network of 74 randomly distributed domestic water-supply wells completed in the central High Plains aquifer was sampled and analyzed from April to August 1999 as part of the High Plains Regional Ground-Water Study conducted by the U. S. Geological Survey National Water-Quality Assessment Program to provide a broad-scale assessment of the ground-water-quality in this part of the High Plains aquifer. Water properties were relatively consistent across the aquifer, with water being alkaline and well oxidized. Water was mostly of the calcium and magnesium-bicarbonate type and very hard. Sulfate concentrations in water from three wells and chloride concentration in water from one well exceeded Secondary Maximum Contaminant Levels. Fluoride concentration was equal to the Maximum Contaminant Level in one sample. Nitrate concentrations was relatively small in most samples, with the median concentration of 2.3 milligrams per liter. Dissolved organic carbon concentration was relatively low, with a median concentration of 0.5 milligram per liter. The Maximum Contaminant Level set by the U.S. Environmental Protection Agency for nitrate as nitrogen of 10 milligrams per liter was exceeded by water samples from three wells. Most samples contained detectable concentrations of the trace elements aluminum, arsenic, barium, chromium, molybdenum, selenium, zinc, and uranium. Only a few samples had trace element concentrations exceeding Maximum Contaminant Levels. Fifty-five of the samples had radon concentrations exceeding the proposed Maximum Contaminant Level of 300 picocuries per liter. The greatest radon concentrations were detected where the Ogallala Formation overlies sandstones, shales and limestones of Triassic, Jurassic, or Cretaceous age. Volatile organic compounds were detected in 9 of 74 samples. Toluene was detected in eight of those nine samples. All volatile organic compound concentrations were substantially less than Maximum Contaminant Levels. Detections of toluene may have been artifacts of the sampling and analytical processes. Pesticides were detected in 18 of the 74 water samples. None of the pesticide concentrations exceeded Maximum Contaminant Levels. The most frequently detected pesticides were atrazine and its metabolite deethylatrazine, which were detected in water from 15 and 17 wells, respectively. Most of the samples with a detectable pesticide had at least two detectable pesticides. Six of the samples had more than two detectable pesticides. Tritium concentrations was greater than 0.5 tritium unit in 10 of 51 samples, indicating recent recharge to the aquifer. Twenty-one of the samples that had nitrate concentrations greater than 4.0 milligrams per liter were assumed to have components of recent recharge. Detection of volatile organic compounds was not associated with those indicators of recent recharge, with most of volatile organic compounds being detected in water from wells with small tritium and nitrate concentrations. Detection of pesticides was associated with greater tritium or nitrate concentrations, with 16 of the 18 wells producing water with pesticides also having tritium or nitrate concentrations indicating recent recharge.

[The epidemiological validation of the MPEL for grain dust in the atmosphere].

PubMed

Pinigin, M A; Cherepov, E M; Safiulin, A A; Petrova, I V; Mukhambetova, L Kh; Osipova, E M; Veselov, A P

1998-01-01

The use of calculating and gravimetric methods for examining the grain dust pollution of the ambient air at the site of an elevator determined the maximum single, mean daily, and mean annual concentrations at different distances from the source of dust emission. The mean ratio of these concentrations was 12.1:4.3:1, respectively. The calculated concentration-effect and concentration-time relationships provided evidence for the maximum single, mean daily, and mean annual allowable concentrations for grain dust in the ambient air.

Electrophysiological and neuromuscular stability of persons with chronic inflammatory demyelinating polyneuropathy.

PubMed

Gilmore, Kevin J; Allen, Matti D; Doherty, Timothy J; Kimpinski, Kurt; Rice, Charles L

2017-09-01

We assessed motor unit (MU) properties and neuromuscular stability in the tibialis anterior (TA) of chronic inflammatory demyelinating polyneuropathy (CIDP) patients using decomposition-based quantitative electromyography. Dorsiflexion strength was assessed, and surface and concentric needle electromyography were sampled from the TA. Estimates of MU numbers were derived using decomposition-based quantitative electromyography and spike-triggered averaging. Neuromuscular transmission stability was assessed from concentric needle-detected MU potentials. CIDP patients had 43% lower compound muscle action potential amplitude than controls, and despite near-maximum voluntary activation, were 37% weaker. CIDP had 27% fewer functioning MUs in the TA, and had 90% and 44% higher jiggle and jitter values, respectively compared with controls. CIDP had lower strength and compound muscle action potential values, moderately fewer numbers of MUs, and significant neuromuscular instability compared with controls. Thus, in addition to muscle atrophy, voluntary weakness is also due to limitations of peripheral neural transmission consistent with demyelination. Muscle Nerve 56: 413-420, 2017. © 2016 Wiley Periodicals, Inc.

Effect of Medium Salt Concentration on Differentiation and Maturation of Somatic Embryos of Cassava (Manihot esculenta Crantz)

PubMed Central

GROLL, J.; MYCOCK, D. J.; GRAY, V. M.

2002-01-01

Culture of cassava somatic embryos on media with an altered macro‐ and micro‐nutrient salt concentration affected embryo development and germination capability. In the tests, quarter‐, half‐, full‐ or double‐strength Murashige and Skoog (MS) media were compared. The maximum number of somatic embryos differentiated from a proliferative nodular embryogenic callus (NEC) on either half‐ or full‐strength MS medium, and the greatest numbers of cotyledonary stage embryos were formed on full‐strength MS medium. Developed somatic embryos were then desiccated above a saturated K2SO4 solution for 10 d. After transfer to germination medium, embryos that had developed on half‐ and full‐strength MS medium yielded 8·3 and 8·6 germinants g–1 NEC tissue, respectively. For this important but often disregarded culture factor, either half‐ or full‐strength MS medium is recommended for both the differentiation and development of cassava somatic embryos that are capable of germination. PMID:12099540

Combination of the Auxins NAA, IBA, and IAA with GA3 Improves the Commercial Seed-Tuber Production of Potato (Solanum tuberosum L.) under In Vitro Conditions

PubMed Central

Kumlay, Ahmet Metin

2014-01-01

The study compared the effects of 1.0 × MS medium containing various concentrations of α-naphthaleneacetic acid (NAA), indole-3-acetic acid (IAA), and indole-3-butyric acid (IBA), alone or in combination with gibberellic acid (GA3) in micropropagation of three potato (Solanum tuberosum L.) cultivars Pasinler, Granola, and Caspar using binodal stem cuttings. The results testified improved regeneration on 1.0 × MS medium containing variants of NAA, IAA, and IBA plus GA3 on all cultivars. The minimum days to shoot induction on three cultivars ranged 4.25–5 d on 1.0 × MS medium containing 0.25 mg L−1  GA3 + 1 mg L−1 NAA. The longest shoots (11.8 cm), maximum number of nodes (13.50), and maximum number of leaves (11.00) were recorded on cv. Caspar on 1.0 × MS medium containing 1 mg L−1  NAA + 0.25 mg L−1 GA3. The minimum time to root induction (12.25 d) was noted on cv. Pasinler on the same medium. All of the regenerated shoots could be easily rooted. The results showed that the combined effect of various concentrations of NAA, IAA, and IBA plus GA3 was more pronounced compared to the auxins used alone. The results of this research are of significant importance for potato breeders. PMID:25028654

Combination of the auxins NAA, IBA, and IAA with GA3 improves the commercial seed-tuber production of potato (Solanum tuberosum L.) under in vitro conditions.

PubMed

Kumlay, Ahmet Metin

2014-01-01

The study compared the effects of 1.0 × MS medium containing various concentrations of α-naphthaleneacetic acid (NAA), indole-3-acetic acid (IAA), and indole-3-butyric acid (IBA), alone or in combination with gibberellic acid (GA3) in micropropagation of three potato (Solanum tuberosum L.) cultivars Pasinler, Granola, and Caspar using binodal stem cuttings. The results testified improved regeneration on 1.0 × MS medium containing variants of NAA, IAA, and IBA plus GA3 on all cultivars. The minimum days to shoot induction on three cultivars ranged 4.25-5 d on 1.0 × MS medium containing 0.25 mg L(-1) GA3 + 1 mg L(-1) NAA. The longest shoots (11.8 cm), maximum number of nodes (13.50), and maximum number of leaves (11.00) were recorded on cv. Caspar on 1.0 × MS medium containing 1 mg L(-1) NAA + 0.25 mg L(-1) GA3. The minimum time to root induction (12.25 d) was noted on cv. Pasinler on the same medium. All of the regenerated shoots could be easily rooted. The results showed that the combined effect of various concentrations of NAA, IAA, and IBA plus GA3 was more pronounced compared to the auxins used alone. The results of this research are of significant importance for potato breeders.

Optimization of properties and operating parameters of a passive DMFC mini-stack at ambient temperature

NASA Astrophysics Data System (ADS)

Baglio, V.; Stassi, A.; Matera, F. V.; Di Blasi, A.; Antonucci, V.; Aricò, A. S.

An investigation of properties and operating parameters of a passive DMFC monopolar mini-stack, such as catalyst loading and methanol concentration, was carried out. From this analysis, it was derived that a proper Pt loading is necessary to achieve the best compromise between electrode thickness and number of catalytic sites for the anode and cathode reactions to occur at suitable rates. Methanol concentrations ranging from 1 M up to 10 M and an air-breathing operation mode were investigated. A maximum power of 225 mW was obtained at ambient conditions for a three-cell stack, with an active single cell area of 4 cm 2, corresponding to a power density of about 20 mW cm -2.

Donor impurity incorporation during layer growth of Zn II-VI semiconductors

NASA Astrophysics Data System (ADS)

Barlow, D. A.

2017-12-01

The maximum halogen donor concentration in Zn II-VI semiconductors during layer growth is studied using a standard model from statistical mechanics. Here the driving force for incorporation is an increase in entropy upon mixing of the donor impurity into the available anion lattice sites in the host binary. A formation energy opposes this increase and thus equilibrium is attained at some maximum concentration. Considering the halogen donor impurities within the Zn II-VI binary semiconductors ZnO, ZnS, ZnSe and ZnTe, a heat of reaction obtained from reported diatomic bond strengths is shown to be directly proportional to the log of maximum donor concentration. The formation energy can then be estimated and an expression for maximum donor concentration derived. Values for the maximum donor concentration with each of the halogen impurities, within the Zn II-VI compounds, are computed. This model predicts that the halogens will serve as electron donors in these compounds in order of increasing effectiveness as: F, Br, I, Cl. Finally, this result is taken to be equivalent to an alternative model where donor concentration depends upon impurity diffusion and the conduction band energy shift due to a depletion region at the growing crystal's surface. From this, we are able to estimate the diffusion activation energy for each of the impurities mentioned above. Comparisons are made with reported values and relevant conclusions presented.

Spacecraft Maximum Allowable Concentrations for Airborne Contaminants

NASA Technical Reports Server (NTRS)

James, John T.

2008-01-01

The enclosed table lists official spacecraft maximum allowable concentrations (SMACs), which are guideline values set by the NASA/JSC Toxicology Group in cooperation with the National Research Council Committee on Toxicology (NRCCOT). These values should not be used for situations other than human space flight without careful consideration of the criteria used to set each value. The SMACs take into account a number of unique factors such as the effect of space-flight stress on human physiology, the uniform good health of the astronauts, and the absence of pregnant or very young individuals. Documentation of the values is given in a 5 volume series of books entitled "Spacecraft Maximum Allowable Concentrations for Selected Airborne Contaminants" published by the National Academy Press, Washington, D.C. These books can be viewed electronically at http://books.nap.edu/openbook.php?record_id=9786&page=3. Short-term (1 and 24 hour) SMACs are set to manage accidental releases aboard a spacecraft and permit risk of minor, reversible effects such as mild mucosal irritation. In contrast, the long-term SMACs are set to fully protect healthy crewmembers from adverse effects resulting from continuous exposure to specific air pollutants for up to 1000 days. Crewmembers with allergies or unusual sensitivity to trace pollutants may not be afforded complete protection, even when long-term SMACs are not exceeded. Crewmember exposures involve a mixture of contaminants, each at a specific concentration (C(sub n)). These contaminants could interact to elicit symptoms of toxicity even though individual contaminants do not exceed their respective SMACs. The air quality is considered acceptable when the toxicity index (T(sub grp)) for each toxicological group of compounds is less than 1, where T(sub grp), is calculated as follows: T(sub grp) = C(sub 1)/SMAC(sub 1) + C(sub 2/SMAC(sub 2) + ...+C(sub n)/SMAC(sub n).

Nationwide reconnaissance of contaminants of emerging ...

EPA Pesticide Factsheets

Mobile and persistent chemicals that are present in urban wastewater, such as pharmaceuticals, may survive on-site or municipal wastewater treatment and post-discharge environmental processes. These pharmaceuticals have the potential to reach surface and groundwaters, essential drinking-water sources. A joint, two-phase U.S. Geological Survey-U.S. Environmental Protection Agency study examined source and treated waters from 25 drinking-water treatment plants from across the United States. Treatment plants that had probable wastewater inputs to their source waters were selected to assess the prevalence of pharmaceuticals in such source waters, and to identify which pharmaceuticals persist through drinking-water treatment. All samples were analyzed for 24 pharmaceuticals in Phase I and for 118 in Phase II. In Phase I, 11 pharmaceuticals were detected in all source-water samples, with a maximum of nine pharmaceuticals detected in any one sample. The median number of pharmaceuticals for all 25 samples was five. Quantifiable pharmaceutical detections were fewer, with a maximum of five pharmaceuticals in any one sample and a median for all samples of two. In Phase II, 47 different pharmaceuticals were detected in all source-water samples, with a maximum of 41 pharmaceuticals detected in any one sample. The median number of pharmaceuticals for all 25 samples was eight. For 37 quantifiable pharmaceuticals in Phase II, median concentrations in source water were below 11

Elasto-inertial turbulence in straight pipes at low Reynolds numbers

NASA Astrophysics Data System (ADS)

Choueiri, George; Hof, Björn

2017-11-01

An early point of contention in the study of polymer drag reduction had been whether polymers delay transition to turbulence or cause it to occur at earlier Reynolds numbers (Re). Recent results have shown that at low polymer concentrations, the subcritical transition to Newtonian type turbulence (NTT) is delayed; however at higher concentrations an elastic instability is encountered which results in a distinct flow state dubbed elasto-inertial turbulence (EIT). Here transition is continuous, fluctuation and friction levels are considerably lower than those for NTT and flow structures are qualitatively different. Several factors can influence the necessary Re for transition to occur for a specific polymer concentration; these include the type of polymer, its molecular weight, the solution viscosity and the proximity of the wall boundaries. By controlling these factors, we have found that chaotic motions can be measured at Re of the order of 1 even in straight smooth pipes as opposed to curved microchannels where curved streamlines cause a purely elastic instability. Furthermore we found that low-Re EIT is closely connected to turbulence that exists on the maximum drag reduction asymptote for polymer solutions with Re several orders of magnitude higher.

Quantifying the impact of current and future concentrations of air pollutants on respiratory disease risk in England.

PubMed

Pannullo, Francesca; Lee, Duncan; Neal, Lucy; Dalvi, Mohit; Agnew, Paul; O'Connor, Fiona M; Mukhopadhyay, Sabyasachi; Sahu, Sujit; Sarran, Christophe

2017-03-27

Estimating the long-term health impact of air pollution in a spatio-temporal ecological study requires representative concentrations of air pollutants to be constructed for each geographical unit and time period. Averaging concentrations in space and time is commonly carried out, but little is known about how robust the estimated health effects are to different aggregation functions. A second under researched question is what impact air pollution is likely to have in the future. We conducted a study for England between 2007 and 2011, investigating the relationship between respiratory hospital admissions and different pollutants: nitrogen dioxide (NO 2 ); ozone (O 3 ); particulate matter, the latter including particles with an aerodynamic diameter less than 2.5 micrometers (PM 2.5 ), and less than 10 micrometers (PM 10 ); and sulphur dioxide (SO 2 ). Bayesian Poisson regression models accounting for localised spatio-temporal autocorrelation were used to estimate the relative risks (RRs) of pollution on disease risk, and for each pollutant four representative concentrations were constructed using combinations of spatial and temporal averages and maximums. The estimated RRs were then used to make projections of the numbers of likely respiratory hospital admissions in the 2050s attributable to air pollution, based on emission projections from a number of Representative Concentration Pathways (RCP). NO 2 exhibited the largest association with respiratory hospital admissions out of the pollutants considered, with estimated increased risks of between 0.9 and 1.6% for a one standard deviation increase in concentrations. In the future the projected numbers of respiratory hospital admissions attributable to NO 2 in the 2050s are lower than present day rates under 3 Representative Concentration Pathways (RCPs): 2.6, 6.0, and 8.5, which is due to projected reductions in future NO 2 emissions and concentrations. NO 2 concentrations exhibit consistent substantial present-day health effects regardless of how a representative concentration is constructed in space and time. Thus as concentrations are predicted to remain above limits set by European Union Legislation until the 2030s in parts of urban England, it will remain a substantial health risk for some time.

Computer simulations of dendrimer-polyelectrolyte complexes.

PubMed

Pandav, Gunja; Ganesan, Venkat

2014-08-28

We carry out a systematic analysis of static properties of the clusters formed by complexation between charged dendrimers and linear polyelectrolyte (LPE) chains in a dilute solution under good solvent conditions. We use single chain in mean-field simulations and analyze the structure of the clusters through radial distribution functions of the dendrimer, cluster size, and charge distributions. The effects of LPE length, charge ratio between LPE and dendrimer, the influence of salt concentration, and the dendrimer generation number are examined. Systems with short LPEs showed a reduced propensity for aggregation with dendrimers, leading to formation of smaller clusters. In contrast, larger dendrimers and longer LPEs lead to larger clusters with significant bridging. Increasing salt concentration was seen to reduce aggregation between dendrimers as a result of screening of electrostatic interactions. Generally, maximum complexation was observed in systems with an equal amount of net dendrimer and LPE charges, whereas either excess LPE or dendrimer concentrations resulted in reduced clustering between dendrimers.

Aquaporins in desert rodent physiology.

PubMed

Pannabecker, Thomas L

2015-08-01

Desert rodents face a sizeable challenge in maintaining salt and water homeostasis due to their life in an arid environment. A number of their organ systems exhibit functional characteristics that limit water loss above that which occurs in non-desert species under similar conditions. These systems include renal, pulmonary, gastrointestinal, nasal, and skin epithelia. The desert rodent kidney preserves body water by producing a highly concentrated urine that reaches a maximum osmolality nearly three times that of the common laboratory rat. The precise mechanism by which urine is concentrated in any mammal is unknown. Insights into the process may be more apparent in species that produce highly concentrated urine. Aquaporin water channels play a fundamental role in water transport in several desert rodent organ systems. The role of aquaporins in facilitating highly effective water preservation in desert rodents is only beginning to be explored. The organ systems of desert rodents and their associated AQPs are described. © 2015 Marine Biological Laboratory.

Particular Film Formation of Phenytoin at Silica Surfaces

PubMed Central

2014-01-01

Given the increasing number of poorly soluble and thus poorly bioavailable active pharmaceutical materials, there is a demand for innovative formulation platforms for such molecules. Thus a focus on enhancing dissolution properties of poorly soluble drugs exists. Within this study, the spin coating of acetone solutions containing 5,5-diphenyl-2,4-imidazolidinedione (phenytoin) in various concentrations is evaluated. The results reveal strong variations of the morphology of deposited phenytoin crystals at silica surfaces. Individual separated particles are obtained on low phenytoin concentrations, and closely packed particular films form when the concentration is increased. As the material is isomorphic, these various morphologies have the same crystalline structure. Dissolution experiments reveal that both the apparent maximum solubility and as the dissolution rate are strongly enhanced compared to bulk powder, suggesting that formulation based on this preparative technique will allow overcoming the low solubility problematic for a variety of drugs. PMID:24417472

Spectral radiance measurements and calculated soot concentrations along the length of an experimental combustor

NASA Technical Reports Server (NTRS)

Norgren, C. T.; Ingebo, R. D.

1976-01-01

Radiometric data were obtained over a range of parametric test conditions at three positions along the length of an experimental combustor segment corresponding to the primary, intermediate, and dilution zones. The concentration of soot entrained in the combustion gases was calculated by a technique using spectral radiance measurements. Tests were conducted primarily with Jet A fuel, although limited data were taken with two fuels having higher aromatic content, diesel oil number 2 and a blend of 40 percent tetralin in Jet A fuel. Radiometric observation of the combustion gases indicated that the maximum total radiance peaked at the intermediate zone, which was located immediately upstream of the dilution holes. Soot concentrations calculated from optical measurements in the dilution zone compared favorably with those obtained by in situ gas sampling at the exhaust. The total radiance increased with the higher aromatic content fuels.

Impact of dyeing industry effluent on germination and growth of pea (Pisum sativum).

PubMed

Malaviya, Piyush; Hali, Rajesh; Sharma, Neeru

2012-11-01

Dye industry effluent was analyzed for physico-chemical characteristics and its impact on germination and growth behaviour of Pea (Pisum sativum). The 100% effluent showed high pH (10.3) and TDS (1088 mg l(-1)). The germination parameters included percent germination, delay index, speed of germination, peak value and germination period while growth parameters comprised of root and shoot length, root and shootweight, root-shoot ratio and number of stipules. The study showed the maximum values of positive germination parameters viz. speed of germination (7.85), peak value (3.28), germination index (123.87) and all growth parameters at 20% effluent concentration while the values of negative germination parameters viz. delay index (-0.14) and percent inhibition (-8.34) were found to be minimum at 20% effluent concentration. The study demonstrated that at lower concentrations the dyeing industry effluent caused a positive impact on germination and growth of Pisum sativum.

Derivation of Hunt equation for suspension distribution using Shannon entropy theory

NASA Astrophysics Data System (ADS)

Kundu, Snehasis

2017-12-01

In this study, the Hunt equation for computing suspension concentration in sediment-laden flows is derived using Shannon entropy theory. Considering the inverse of the void ratio as a random variable and using principle of maximum entropy, probability density function and cumulative distribution function of suspension concentration is derived. A new and more general cumulative distribution function for the flow domain is proposed which includes several specific other models of CDF reported in literature. This general form of cumulative distribution function also helps to derive the Rouse equation. The entropy based approach helps to estimate model parameters using suspension data of sediment concentration which shows the advantage of using entropy theory. Finally model parameters in the entropy based model are also expressed as functions of the Rouse number to establish a link between the parameters of the deterministic and probabilistic approaches.

Water-quality and amphibian population data for Maryland, Washington, D.C., and Virginia, 2001-2004

USGS Publications Warehouse

Rice, K.C.; Jung, R.E.

2004-01-01

Data on the chemical composition of water and on amphibian populations were collected at least annually from vernal pool and stream sites in Maryland, Washington, D.C., and Virginia, from 2001 through 2004. The data were collected as part of long-term monitoring projects of the Northeast Region of the Amphibian Research and Monitoring Initiative (ARMI) of the U.S. Geological Survey. Water samples were analyzed for temperature, specific conductance, pH, dissolved-oxygen concentration, acid-neutralizing capacity, and concentrations of total Kjeldahl nitrogen and total phosphorus; in 2004, samples also were analyzed for nitrite plus nitrate concentrations and total nitrogen concentrations. Field and laboratory analytical results of water samples and quality-assurance information are presented. Amphibian population data include the presence of amphibian species and the maximum number of egg masses of wood frogs and spotted salamanders at vernal pools, and counts of amphibians made during stream transect and stream quadrat surveys.

First Map of Residential Indoor Radon Measurements in Azerbaijan.

PubMed

Hoffmann, M; Aliyev, C S; Feyzullayev, A A; Baghirli, R J; Veliyeva, F F; Pampuri, L; Valsangiacomo, C; Tollefsen, T; Cinelli, G

2017-06-15

This article describes results of the first measurements of indoor radon concentrations in Azerbaijan, including description of the methodology and the mathematical and statistical processing of the results obtained. Measured radon concentrations varied considerably: from almost radon-free houses to around 1100 Bq m-3. However, only ~7% of the total number of measurements exceeded the maximum permissible concentrations. Based on these data, maps of the distribution of volumetric activity and elevated indoor radon concentrations in Azerbaijan were created. These maps reflect a mosaic character of distribution of radon and enhanced values that are confined to seismically active areas at the intersection of an active West Caspian fault with sub-latitudinal faults along the Great and Lesser Caucasus and the Talysh mountains. Spatial correlation of radon and temperature behavior is also described. The data gathered on residential indoor radon have been integrated into the European Indoor Radon Map. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Treatment of chromium contaminated soil using bioremediation

NASA Astrophysics Data System (ADS)

Purwanti, Ipung Fitri; Putri, Tesya Paramita; Kurniawan, Setyo Budi

2017-11-01

Chromium contamination in soil occurs due to the disposal of chromium industrial wastewater or sludge that excess the quality standard. Chromium concentration in soil is ranged between 1 to 300 mg/kg while the maximum health standard is 2.5 mg/kg. Bioremediation is one of technology that could be used for remediating heavy metal contamination in soil. Bacteria have an ability to remove heavy metal from soil. One bacteria species that capable to remove chromium from soil is Bacillus subtilis. The aim of this research was to know the chromium removal percentage in contaminated soil by Bacillus subtilis. Artificial chromium contaminated soil was used by mixing 425gram sand and chromium trichloride solution. Concentration of chromium added into the spiked soil were 50, 75, and 100 mg/L. During 14 days, pH, soil temperature and soil moisture were tested. Initial and final number of bacterial colony and chromium concentration analysed. The result showed that the highest percentage of chromium removal was 11% at a chromium concentration of 75 mg/L

Spacecraft maximum allowable concentrations for selected airborne contaminants, volume 1

NASA Technical Reports Server (NTRS)

1994-01-01

As part of its efforts to promote safe conditions aboard spacecraft, NASA requested the National Research Council (NRC) to develop guidelines for establishing spacecraft maximum allowable concentrations (SMAC's) for contaminants, and to review SMAC's for various spacecraft contaminants to determine whether NASA's recommended exposure limits are consistent with the guidelines recommended by the subcommittee. In response to NASA's request, the NRC organized the Subcommittee on Guidelines for Developing Spacecraft Maximum Allowable Concentrations for Space Station Contaminants within the Committee on Toxicology (COT). In the first phase of its work, the subcommittee developed the criteria and methods for preparing SMAC's for spacecraft contaminants. The subcommittee's report, entitled Guidelines for Developing Spacecraft Maximum Allowable Concentrations for Space Station Contaminants, was published in 1992. The executive summary of that report is reprinted as Appendix A of this volume. In the second phase of the study, the Subcommittee on Spacecraft Maximum Allowable Concentrations reviewed reports prepared by NASA scientists and contractors recommending SMAC's for 35 spacecraft contaminants. The subcommittee sought to determine whether the SMAC reports were consistent with the 1992 guidelines. Appendix B of this volume contains the first 11 SMAC reports that have been reviewed for their application of the guidelines developed in the first phase of this activity and approved by the subcommittee.

A variable circular-plot method for estimated bird numbers

USGS Publications Warehouse

Reynolds, R.T.; Scott, J.M.; Nussbaum, R.A.

1980-01-01

A bird census method is presented that is designed for tall, structurally complex vegetation types, and rugged terrain. With this method the observer counts all birds seen or heard around a station, and estimates the horizontal distance from the station to each bird. Count periods at stations vary according to the avian community and structural complexity of the vegetation. The density of each species is determined by inspecting a histogram of the number of individuals per unit area in concentric bands of predetermined widths about the stations, choosing the band (with outside radius x) where the density begins to decline, and summing the number of individuals counted within the circle of radius x and dividing by the area (Bx2). Although all observations beyond radius x are rejected with this procedure, coefficients of maximum distance.

Contribution of pollen to atmospheric ice nuclei concentrations

NASA Astrophysics Data System (ADS)

Hader, J. D.; Wright, T. P.; Petters, M. D.

2014-06-01

Recent studies have suggested that the ice-nucleating ability of some types of pollen is derived from non-proteinaceous macromolecules. These macromolecules may become dispersed by the rupturing of the pollen grain during wetting and drying cycles in the atmosphere. If true, this mechanism might prove to be a significant source of ice nuclei (IN) concentrations when pollen is present. Here we test this hypothesis by measuring ambient IN concentrations from the beginning to the end of the 2013 pollen season in Raleigh, North Carolina, USA. Air samples were collected using a swirling aerosol collector twice per week and the solutions were analysed for ice nuclei activity using a droplet freezing assay. Rainwater samples were collected at times when pollen grain number concentrations were near their maximum value and analysed with the drop-freezing assay to compare the potentially enhanced IN concentrations measured near the ground with IN concentrations found aloft. Ambient ice nuclei spectra, defined as the number of ice nuclei per volume of air as a function of temperature, are inferred from the aerosol collector solutions. No general trend was observed between ambient pollen grain counts and observed IN concentrations, suggesting that ice nuclei multiplication via pollen grain rupturing and subsequent release of macromolecules was not prevalent for the pollen types and meteorological conditions typically encountered in the southeastern US. A serendipitously sampled collection after a downpour provided evidence for a rain-induced IN burst with an observed IN concentration of approximately 30 per litre, a 30-fold increase over background concentrations at -20 °C. The onset temperature of freezing for these particles was approximately -12 °C, suggesting that the ice-nucleating particles were biological in origin.

Investigation of particle inertial migration in high particle concentration suspension flow by multi-electrodes sensing and Eulerian-Lagrangian simulation in a square microchannel

PubMed Central

Zhao, Tong; Liu, Kai; Takei, Masahiro

2016-01-01

The inertial migration of neutrally buoyant spherical particles in high particle concentration (αpi > 3%) suspension flow in a square microchannel was investigated by means of the multi-electrodes sensing method which broke through the limitation of conventional optical measurement techniques in the high particle concentration suspensions due to interference from the large particle numbers. Based on the measured particle concentrations near the wall and at the corner of the square microchannel, particle cross-sectional migration ratios are calculated to quantitatively estimate the migration degree. As a result, particle migration to four stable equilibrium positions near the centre of each face of the square microchannel is found only in the cases of low initial particle concentration up to 5.0 v/v%, while the migration phenomenon becomes partial as the initial particle concentration achieves 10.0 v/v% and disappears in the cases of the initial particle concentration αpi ≥ 15%. In order to clarify the influential mechanism of particle-particle interaction on particle migration, an Eulerian-Lagrangian numerical model was proposed by employing the Lennard-Jones potential as the inter-particle potential, while the inertial lift coefficient is calculated by a pre-processed semi-analytical simulation. Moreover, based on the experimental and simulation results, a dimensionless number named migration index was proposed to evaluate the influence of the initial particle concentration on the particle migration phenomenon. The migration index less than 0.1 is found to denote obvious particle inertial migration, while a larger migration index denotes the absence of it. This index is helpful for estimation of the maximum initial particle concentration for the design of inertial microfluidic devices. PMID:27158288

40 CFR 421.113 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... Maximum for monthly average mg/kg (pounds per million pounds) of concentrate digested Lead .174 .081 Zinc... monthly average mg/Kg (pounds per million pounds) of concentrate digested Lead 2.592 1.203 Zinc 9.442 3... Maximum for monthly average mg/kg (pounds per million pounds) of concentrate digested Lead .069 .032 Zinc...

40 CFR 421.113 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... Maximum for monthly average mg/kg (pounds per million pounds) of concentrate digested Lead .174 .081 Zinc... monthly average mg/Kg (pounds per million pounds) of concentrate digested Lead 2.592 1.203 Zinc 9.442 3... Maximum for monthly average mg/kg (pounds per million pounds) of concentrate digested Lead .069 .032 Zinc...

Distribution of trace gases and aerosols in the Siberian air shed during wildfires of summer 2012

NASA Astrophysics Data System (ADS)

Belan, Boris D.; Paris, Jean-Daiel; Nedelec, Philippe; Antokhin, Pavel N.; Arshinova, Victoriya; Arshinov, Mikhail Yu.; Belan, Sergey B.; Davydov, Denis K.; Ivlev, Georgii A.; Fofonov, Alexandre V.; Kozlov, Artem V.; Rasskazchikova, Tatyana M.; Savkin, Denis E.; Simonenkov, Denis V.; Sklyadneva, Tatyana K.; Tolmachev, Gennadii N.

2017-04-01

During the last two decades, three strong biomass burning events have been observed in Russia: two of them in 2002 and 2010 in the European part of Russia, and another one in 2012 in West and East Siberia. In this paper we present results of the extensive airborne study of the vertical distribution of trace gases and aerosols carried out during strong wildfire event happened in summer 2012 in Siberia. For this purpose, the Optik TU-134 aircraft laboratory was used as a research platform. A large-scale airborne campaign has been undertaken along the route Novosibirsk-Mirny-Yakutsk-Bratsk-Novosibirsk on 31st of July and 1st of August, 2012. Flight pattern consisted of a number of ascents and descents between close to the ground and 8 km altitude that enabled 20 vertical profiles to be obtained. Campaign was conducted under the weather conditions of low-gradient baric field that determined the low speed transport of air masses, as well as the accumulation of biomass burning emissions in the region under study. Highest concentrations of CO2, CH4 and CO over wildfire spots reached 432 ppm, 2367 ppb, and 4036 ppb, correspondingly. If we exclude from the analysis the data obtained when crossing smoke plumes, we can find a difference between background concentrations measured in the atmosphere over regions affected by biomass burning and clean areas. Enhancement of CO2 over the wildfire areas changed with altitude. On average, it was 10.5 ppm in the atmospheric boundary layer (ABL) and 5-6 ppm in the free troposphere. Maximum CO2 enhancements reached 27 ppm and 24 ppm, correspondingly. The averaged CH4 enhancement varied from 75 ppb in the boundary layer to 30 ppb in the upper troposphere, and a little bit lower than 30 ppb in the middle troposphere. Maximum CH4 enhancements reached 202 ppb, 108 ppb, and 50-60 ppb, correspondingly. The averaged and maximum enhancements of CO differed by an order of magnitude. Thus, in the ABL the maximum difference in concentration between clean and wildfire areas reached 2300 ppb, while averaged one was 170 ppb. In the middle troposphere maximum enhancements varied from 1000 to 1700 ppb. The vertical distribution of ozone has its own peculiarities. Ozone concentration decreased in the layers with enhanced aerosol concentration and it increased in the areas with lower aerosol content. At the same time, photochemical production ozone was observed at the plume edges in the zone of fresh air entrainment. This work was supported by the Russian Foundation for Basic Research (grant No 17-05-00374).

Water quality of the Mississippian carbonate aquifer in parts of middle Tennessee and northern Alabama, 1999

USGS Publications Warehouse

Kingsbury, James A.; Shelton, John M.

2002-01-01

Water-quality data for nitrate, fecal-indicator bacteria, pesticides, and volatile organic compounds collected in parts of Middle Tennessee and northern Alabama indicate that the Mississippian carbonate aquifer in these areas is susceptible to contamination from point and nonpoint sources. Thirty randomly located wells (predominantly domestic), two springs, and two additional public-supply wells were sampled in the summer of 1999 as part of the U.S. Geological Survey?s National Water-Quality Assessment (NAWQA) Program. These wells and springs were sampled to characterize the occurrence and distribution of the above constituents in this karst aquifer of Mississippian age and to determine the principal environmental factors related to their occurrence.Nitrate and fecal indicator bacteria were frequently detected at the sampled sites. Nitrate exceeded the drinking-water maximum contaminant level of 10 milligrams per liter in two samples; the median concentration for all samples was about 1.5 milligrams per liter. Correlation of nitrate concentrations to the amount of cropland near a site and to pesticide detections indicates that fertilizer application is the predominant source of nitrogen to the aquifer. Fecal-indicator bacteria were present in samples from about 40 percent of the sites. The presence of fecal-indicator bacteria is weakly correlated to the depth to ground water but is not correlated to a specific land use near the sites.Pesticides and pesticide breakdown products (metabolites) were detected at 74 percent of the sites sampled. Concentrations generally were less than 1 microgram per liter and no pesticide detections exceeded drinking-water maximum contaminant levels. The maximum total pesticide concentration measured was about 4 micrograms per liter. Intensity of pesticide use, proximity of sites to areas of pesticide application, and soil hydrologic group were the primary factors affecting the occurrence of pesticides.Volatile organic compounds were detected at generally low concentrations at about 81 percent of the sites sampled. Concentrations of trichloroethylene, tetrachloroethylene, and 1,2-dichloropropane at three sites equalled or exceeded drinking-water maximum contaminant levels. The maximum concentration measured was 7.5 micrograms per liter of trichloroethylene. The presence of volatile organic compounds in the Mississippian carbonate aquifer was not related to hydrogeology, soil properties, or land use near the sites; although higher total volatile organic compound concentrations and greater numbers of compounds in samples generally were associated with a higher percentage of urban land use near a site. Chloroform was the most frequently detected compound, and correlation of low-level detections to the amount of wetlands near sites having these detections may indicate biogenic formation of chloroform.The relation between land use and water quality was stronger for constituents that are contributed to the environment systematically (fertilizer and pesticide applications), than those contributed inadvertently (leaking septic tanks or chemical spills or leaks). Land use and soils characterized in circular buffer areas near sites sampled in this karst aquifer explained some of the variation in nitrate concentration and presence of pesticides. Use of land use and soil data with greater detail than the large scale data used in this analysis and buffer areas based on well capacities and ground-water withdrawals might strengthen this type of analysis.

21 CFR 172.818 - Oxystearin.

Code of Federal Regulations, 2010 CFR

2010-04-01

... additive is a mixture of the glycerides of partially oxidized stearic and other fatty acids obtained by... specifications: Acid number: Maximum 15. Iodine number: Maximum 15. Saponification number: 225-240. Hydroxyl...

Monitoring and analysis of combustion aerosol emissions from fast moving diesel trains.

PubMed

Burchill, Michael J; Gramotnev, Dmitri K; Gramotnev, Galina; Davison, Brian M; Flegg, Mark B

2011-02-01

In this paper we report the results of the detailed monitoring and analysis of combustion emissions from fast moving diesel trains. A new highly efficient monitoring methodology is proposed based on the measurements of the total number concentration (TNC) of combustion aerosols at a fixed point (on a bridge overpassing the railway) inside the violently mixing zone created by a fast moving train. Applicability conditions for the proposed methodology are presented, discussed and linked to the formation of the stable and uniform mixing zone. In particular, it is demonstrated that if such a mixing zone is formed, the monitoring results are highly consistent, repeatable (with typically negligible statistical errors and dispersion), stable with respect to the external atmospheric turbulence and result in an unusual pattern of the aerosol evolution with two or three distinct TNC maximums. It is also shown that the stability and uniformity of the created mixing zone (as well as the repeatability of the monitoring results) increase with increasing length of the train (with an estimated critical train length of ~10 carriages, at the speed of ~150km/h). The analysis of the obtained evolutionary dependencies of aerosol TNC suggests that the major possible mechanisms responsible for the formation of the distinct concentration maximums are condensation (the second maximum) and thermal fragmentation of solid nanoparticle aggregates (third maximum). The obtained results and the new methodology will be important for monitoring and analysis of combustion emissions from fast moving trains, and for the determination of the impact of rail networks on the atmospheric environment and human exposure to combustion emissions. Copyright © 2010 Elsevier B.V. All rights reserved.

In-situ observations of Eyjafjallajökull ash particles by hot-air balloon

NASA Astrophysics Data System (ADS)

Petäjä, T.; Laakso, L.; Grönholm, T.; Launiainen, S.; Evele-Peltoniemi, I.; Virkkula, A.; Leskinen, A.; Backman, J.; Manninen, H. E.; Sipilä, M.; Haapanala, S.; Hämeri, K.; Vanhala, E.; Tuomi, T.; Paatero, J.; Aurela, M.; Hakola, H.; Makkonen, U.; Hellén, H.; Hillamo, R.; Vira, J.; Prank, M.; Sofiev, M.; Siitari-Kauppi, M.; Laaksonen, A.; lehtinen, K. E. J.; Kulmala, M.; Viisanen, Y.; Kerminen, V.-M.

2012-03-01

The volcanic ash cloud from Eyjafjallajökull volcanic eruption seriously distracted aviation in Europe. Due to the flight ban, there were only few in-situ measurements of the properties and dispersion of the ash cloud. In this study we show in-situ observations onboard a hot air balloon conducted in Central Finland together with regional dispersion modelling with SILAM-model during the eruption. The modeled and measured mass concentrations were in a qualitative agreement but the exact elevation of the layer was slightly distorted. Some of this discrepancy can be attributed to the uncertainty in the initial emission height and strength. The observed maximum mass concentration varied between 12 and 18 μg m -3 assuming a density of 2 g m -3, whereas the gravimetric analysis of the integrated column showed a maximum of 45 μg m -3 during the first two descents through the ash plume. Ion chromatography data indicated that a large fraction of the mass was insoluble to water, which is in qualitative agreement with single particle X-ray analysis. A majority of the super-micron particles contained Si, Al, Fe, K, Na, Ca, Ti, S, Zn and Cr, which are indicative for basalt-type rock material. The number concentration profiles indicated that there was secondary production of particles possibly from volcano-emitted sulfur dioxide oxidized to sulfuric acid during the transport.

Fluorescence chemodosimeter for dopamine based on the inner filter effect of the in situ generation of silver nanoparticles and fluorescent dye

NASA Astrophysics Data System (ADS)

Uppa, Yuwapon; Ngamdee, Kessarin; Promarak, Vinich; Ngeontae, Wittaya

2018-07-01

A new strategy for the sensitive and selective detection of dopamine (DA) was proposed. The chemodosimeter design was based on the measurement of the fluorescent quenching of fluorescein dye caused by the in situ generation of silver nanoparticles (AgNPs). The AgNPs can be simply generated by a reaction between DA and Ag+ in the presence of polymethacrylic acid (PMAA). In addition, the generated AgNPs possess the maximum surface plasmon resonance (SPR) at 440 nm and an increase in the SPR intensity with an increasing DA concentration. Basically, fluorescein dye can emit the fluorescent intensity maximum at 513 nm with excitation at 487 nm. Thus, fluorescent quenching was achieved due to an inner filter effect from the overlap between the excitation spectrum of the fluorescein dye and the SPR spectrum of the generated AgNPs. The degree of fluorescent quenching linearly depends on the number of generated AgNPs that can be directly related to the concentration of DA. The proposed chemodosimeter can be used to detect DA in a working linear concentration range of 1.0-5.0 μM at a detection limit of 10.6 nM. This chemodosimeter was successfully applied to determine DA in a real urine sample and a dopamine injection formulation with satisfactory results.

Concentration-response of short-term ozone exposure and hospital admissions for asthma in Texas.

PubMed

Zu, Ke; Liu, Xiaobin; Shi, Liuhua; Tao, Ge; Loftus, Christine T; Lange, Sabine; Goodman, Julie E

2017-07-01

Short-term exposure to ozone has been associated with asthma hospital admissions (HA) and emergency department (ED) visits, but the shape of the concentration-response (C-R) curve is unclear. We conducted a time series analysis of asthma HAs and ambient ozone concentrations in six metropolitan areas in Texas from 2001 to 2013. Using generalized linear regression models, we estimated the effect of daily 8-hour maximum ozone concentrations on asthma HAs for all ages combined, and for those aged 5-14, 15-64, and 65+years. We fit penalized regression splines to evaluate the shape of the C-R curves. Using a log-linear model, estimated risk per 10ppb increase in average daily 8-hour maximum ozone concentrations was highest for children (relative risk [RR]=1.047, 95% confidence interval [CI]: 1.025-1.069), lower for younger adults (RR=1.018, 95% CI: 1.005-1.032), and null for older adults (RR=1.002, 95% CI: 0.981-1.023). However, penalized spline models demonstrated significant nonlinear C-R relationships for all ages combined, children, and younger adults, indicating the existence of thresholds. We did not observe an increased risk of asthma HAs until average daily 8-hour maximum ozone concentrations exceeded approximately 40ppb. Ozone and asthma HAs are significantly associated with each other; susceptibility to ozone is age-dependent, with children at highest risk. C-R relationships between average daily 8-hour maximum ozone concentrations and asthma HAs are significantly curvilinear for all ages combined, children, and younger adults. These nonlinear relationships, as well as the lack of relationship between average daily 8-hour maximum and peak ozone concentrations, have important implications for assessing risks to human health in regulatory settings. Copyright © 2017. Published by Elsevier Ltd.

The investigation of MCM-48-type and MCM-41-type mesoporous silica as oral solid dispersion carriers for water insoluble cilostazol.

PubMed

Wang, Yanzhu; Sun, Lizhang; Jiang, Tongying; Zhang, Jinghai; Zhang, Chen; Sun, Changshan; Deng, Yihui; Sun, Jin; Wang, Siling

2014-06-01

To explore the suitable application of MCM-41 (Mobil Composition of Matter number forty-one)-type and MCM-48-type mesoporous silica in the oral water insoluble drug delivery system. Cilostazol (CLT) as a model drug was loaded into synthesized MCM-48 (Mobil Composition of Matter number forty-eight) and commercial MCM-41 by three common methods. The obtained MCM-41, MCM-48 and CLT-loaded samples were characterized by means of nitrogen adsorption, thermogravimetric analysis, ultraviolet-visible spectrophotometry, scanning electron microscopy, transmission electron microscopy, differential scanning calorimetry and powder X-ray diffractometer. It was found that solvent evaporation method was preferred according to the drug loading efficiency and the maximum percent cumulative drug dissolution. MCM-48 with 3D cubic pore structure and MCM-41 with 2D long tubular structure are nearly spherical particles in 300-500 nm. Nevertheless, the silica carriers with similar large specific surface areas and concentrating pore size distributions (978.66 m(2)/g, 3.8 nm for MCM-41 and 1108.04 m(2)/g, 3.6 nm for MCM-48) exhibited different adsorption behaviors for CLT. The maximum percent cumulative drug release of the two CLT/silica solid dispersion (CLT-MCM-48 and CLT-MCM-41) was 63.41% and 85.78% within 60 min, respectively; while in the subsequent 12 h release experiment, almost 100% cumulative drug release were both obtained. In the pharmacokinetics aspect, the maximum plasma concentrations of CLT-MCM-48 reached 3.63 mg/L by 0.92 h. The AUC0-∞ values of the CLT-MCM-41 and CLT-MCM-48 were 1.14-fold and 1.73-fold, respectively, compared with the commercial preparation. Our findings suggest that MCM-41-type and MCM-48-type mesoporous silica have great promise as solid dispersion carriers for sustained and immediate release separately.

Propagating Water Quality Analysis Uncertainty Into Resource Management Decisions Through Probabilistic Modeling

NASA Astrophysics Data System (ADS)

Gronewold, A. D.; Wolpert, R. L.; Reckhow, K. H.

2007-12-01

Most probable number (MPN) and colony-forming-unit (CFU) are two estimates of fecal coliform bacteria concentration commonly used as measures of water quality in United States shellfish harvesting waters. The MPN is the maximum likelihood estimate (or MLE) of the true fecal coliform concentration based on counts of non-sterile tubes in serial dilution of a sample aliquot, indicating bacterial metabolic activity. The CFU is the MLE of the true fecal coliform concentration based on the number of bacteria colonies emerging on a growth plate after inoculation from a sample aliquot. Each estimating procedure has intrinsic variability and is subject to additional uncertainty arising from minor variations in experimental protocol. Several versions of each procedure (using different sized aliquots or different numbers of tubes, for example) are in common use, each with its own levels of probabilistic and experimental error and uncertainty. It has been observed empirically that the MPN procedure is more variable than the CFU procedure, and that MPN estimates are somewhat higher on average than CFU estimates, on split samples from the same water bodies. We construct a probabilistic model that provides a clear theoretical explanation for the observed variability in, and discrepancy between, MPN and CFU measurements. We then explore how this variability and uncertainty might propagate into shellfish harvesting area management decisions through a two-phased modeling strategy. First, we apply our probabilistic model in a simulation-based analysis of future water quality standard violation frequencies under alternative land use scenarios, such as those evaluated under guidelines of the total maximum daily load (TMDL) program. Second, we apply our model to water quality data from shellfish harvesting areas which at present are closed (either conditionally or permanently) to shellfishing, to determine if alternative laboratory analysis procedures might have led to different management decisions. Our research results indicate that the (often large) observed differences between MPN and CFU values for the same water body are well within the ranges predicted by our probabilistic model. Our research also indicates that the probability of violating current water quality guidelines at specified true fecal coliform concentrations depends on the laboratory procedure used. As a result, quality-based management decisions, such as opening or closing a shellfishing area, may also depend on the laboratory procedure used.

Distribution of randomly diffusing particles in inhomogeneous media

NASA Astrophysics Data System (ADS)

Li, Yiwei; Kahraman, Osman; Haselwandter, Christoph A.

2017-09-01

Diffusion can be conceptualized, at microscopic scales, as the random hopping of particles between neighboring lattice sites. In the case of diffusion in inhomogeneous media, distinct spatial domains in the system may yield distinct particle hopping rates. Starting from the master equations (MEs) governing diffusion in inhomogeneous media we derive here, for arbitrary spatial dimensions, the deterministic lattice equations (DLEs) specifying the average particle number at each lattice site for randomly diffusing particles in inhomogeneous media. We consider the case of free (Fickian) diffusion with no steric constraints on the maximum particle number per lattice site as well as the case of diffusion under steric constraints imposing a maximum particle concentration. We find, for both transient and asymptotic regimes, excellent agreement between the DLEs and kinetic Monte Carlo simulations of the MEs. The DLEs provide a computationally efficient method for predicting the (average) distribution of randomly diffusing particles in inhomogeneous media, with the number of DLEs associated with a given system being independent of the number of particles in the system. From the DLEs we obtain general analytic expressions for the steady-state particle distributions for free diffusion and, in special cases, diffusion under steric constraints in inhomogeneous media. We find that, in the steady state of the system, the average fraction of particles in a given domain is independent of most system properties, such as the arrangement and shape of domains, and only depends on the number of lattice sites in each domain, the particle hopping rates, the number of distinct particle species in the system, and the total number of particles of each particle species in the system. Our results provide general insights into the role of spatially inhomogeneous particle hopping rates in setting the particle distributions in inhomogeneous media.

Relation of pesticide concentrations to season, streamflow, and land use in seven New Jersey streams

USGS Publications Warehouse

Reiser, Robert G.

1999-01-01

The presence and variability of pesticides in seven New Jersey streams was documented by analyzing 146 samples collected from the streams from April 1996 through June 1998. The samples were analyzed for 85 pesticides, including 50 herbicides, 28 insecticides, and 7 degradation products, at method detection limits that ranged from 0.001 to 0.018 μg/L (micrograms per liter). Pesticides were frequently detected; however, concentrations were generally low. The pesticides most frequently detected were atrazine, in 97 percent of the samples; prometon, 96 percent; metolachlor, 95 percent; desethyl-atrazine, 91 percent; simazine, 88 percent; diazinon, 58 percent; alachlor, 56 percent; and carbaryl, 54 percent. Detection frequencies were highest during the growing season (April-September). At least one pesticide was detected in all but one of these samples, and 49 percent of the samples contained 9 or more pesticides. The numbers of pesticides detected at a given site ranged from 13 to 29. Ten pesticides were detected at concentrations that exceeded established water-quality criteria. Thirty-one of these detections were in samples collected during the growing season and one during the nongrowing season. The pesticides that exceeded the U.S. Environmental Protection Agency (USEPA) maximum contaminant level for drinking water were atrazine, which exceeded 3 μg/L in four samples, and alachlor, 2 μg/L in two samples. Cyanazine exceeded the USEPA liftime health advisory level (HAL) of 1 μg/L in two samples. These eight detections occurred during runoff shortly after spring pesticide applications and represent a potential threat to municipal water supplies in the Raritan River basin. Concentrations of chlorpyrifos, chlorthalonil, diazinon, ethyl-parathion, and methyl-azinphos exceeded the chronic life criteria for the protection of aquatic life (ACQR) in 20 samples at four sites during the growing season. Dieldrin was detected in four samples and DDE in two samples at concentrations that exceeded New Jersey Department of Environmental Protection (NJDEP) human health criteria. Individual and total-pesticide concentrations and total numbers of pesticides detected in the samples varied with season and flow conditions. Median and maximum concentrations of most of the pesticides were highest during runoff in the growing season. Pesticide concentrations were typically lower and less variable in the nongrowing season than in the growing season, regardless of changes in hydrologic conditions; however, median concentrations of most pesticides were slightly lower during runoff than during base flow. The median total-pesticide concentration and median total number of pesticides detected were highest and most variable in runoff samples in the growing season. In the nongrowing season, the median total-pesticide concentration was lowest in runoff samples and least variable during base-flow conditions. Median total numbers of pesticides were lowest and least varibale in the nongrowing season during base-flow conditions at most sites. The highest total-pesticide concentrations were detected in samples from the two small agricultural basins (greater than 25 percent of land use is agricultural) during runoff in late spring and early summer. In general, insecticides were detected more frequently and in greater concentrations at urban sites. Concentrations of agricultural herbicides generally decreased with increasing flow at the four sites with less than 10 percent agriculture land use and increased with increasing flow at the three sites with more than 25 percent agricultural land use. Most of the pesticides that correlated positively with streamflow were detected at sites where land use in the basin would indicate the use of those particular pesticides. Most of the pesticides that correlated negatively with streamflow were present at the site in the Coastal Plain or at sites in which the land use in the basin would not indicate heavy u

Rheology and fluid mechanics of a hyper-concentrated biomass suspension

NASA Astrophysics Data System (ADS)

Botto, Lorenzo; Xu, Xiao

2013-11-01

The production of bioethanol from biomass material originating from energy crops requires mixing of highly concentrated suspensions, which are composed of millimetre-sized lignocellulosic fibers. In these applications, the solid concentration is typically extremely high. Owing to the large particle porosity, for a solid mass concentration slightly larger than 10%, the dispersed solid phase can fill the available space almost completely. To extract input parameters for simulations, we have carried out rheological measurements of a lignocellulosic suspension of Miscanthus, a fast-growing plant, for particle concentrations close to maximum random packing. We find that in this regime the rheometric curves exhibit features similar to those observed in model ``gravitational suspensions,'' including viscoplastic behaviour, strong shear-banding, non-continuum effects, and a marked influence of the particle weight. In the talk, these aspects will be examined in some detail, and differences between Miscanthus and corn stover, currently the most industrially relevant biomass substrate, briefly discussed. We will also comment on values of the Reynolds and Oldroyd numbers found in biofuel applications, and the flow patterns expected for these parameter values.

Time-of-travel and dispersion studies, Lehigh River, Francis E. Walter Lake to Easton, Pennsylvania

USGS Publications Warehouse

Kauffman, C.D.

1983-01-01

Results of time-of-travel and dispersion studies are presented for the 77.0 mile reach of the Lehigh River from Francis E. Walter Lake to Easton, Pennsylvania. Rhodamine WT dye was injected at several points for a variety of several common flow conditions and its downstream travel was monitored at a number of downstream points by means of a fluorometer. Time-of-travel data have been related to stream discharge, distance along the river channel and dispersion. If 2.205 pounds of a conservative water soluble contaminant were accidentally spilled into the Lehigh River at Penn Haven Junction at Black Creek 6.09 miles downstream from Rockport, Pennsylvania, when the discharge at Walnutport, Pennsylvania, was 600 cubic feet per second, the leading edge, peak, and trailing edge of the contaminant would arrive 31.6 miles downstream at the Northhampton, Pennsylvania, water intakes 45, 54, and 66 hours later, respectively. The maximum concentration expected at the intakes would be about 1.450 micrograms per liter. From data and relations presented, time-of-travel and maximum concentration estimates can be made for any two points within the reach. (USGS)

Sodium tripolyphosphate cross-linked chitosan based sensor for enhacing sensing properties towards acetone

NASA Astrophysics Data System (ADS)

Nasution, T. I.; Asrosa, R.; Nainggolan, I.; Balyan, M.; Indah, R.; Wahyudi, A.

2018-02-01

In this report, sensing properties of sodium tripolyphosphate (TPP) cross-linked chitosan based sensor has been successfully enhanced towards acetone. Chitosan solutions were cross-linked with sodium TPP in variation of 0.1%, 0.5%, 1% and 1.5% w/v, respectively. The sensors were fabricated in film form using an electrochemical deposition method. The sensing properties of the sensors were observed by exposing the pure chitosan and sodium TPP cross-linked chitosan sensors towards acetone concentrations of 5, 10, 50, 100 and 200 ppm. The measurement results revealed that the maximum response in output voltage value of pure chitosan sensor was 0.35 V while sodium TPP crosslinked chitosan sensors were above 0.35 V towards 5 ppm acetone concentration. When the sensors were exposed towards acetone concentration of 200 ppm, the maximum response of pure chitosan was 0.45 V while sodium TPP crosslinked chitosan sensors were above 0.45 V. Amongst the variation of sodium TPP, the maximum response of 1% sodium TPP was the highest since the maximum response was 0.4 V and 0.6 V towards 5 ppm and 200 ppm acetone concentration, respectively. While the maximum responses of other sodium TPP concentrations were under 0.4 V and 0.6 V towards 5 ppm and 200 ppm acetone concentration. Moreover, 1% sodium TPP cross-linked chitosan based sensor showed good reproducibility and outstanding lifetime. Therefore, 1% sodium TPP cross-linked chitosan based sensor has exhibited remarkable sensing properties as a novel acetone sensor.

Occurrence and distribution of fecal indicator bacteria, and physical and chemical indicators of water quality in streams receiving discharge from Dallas/Fort Worth International Airport and vicinity, North-Central Texas, 2008

USGS Publications Warehouse

Harwell, Glenn R.; Mobley, Craig A.

2009-01-01

This report, done by the U.S. Geological Survey in cooperation with Dallas/Fort Worth International (DFW) Airport in 2008, describes the occurrence and distribution of fecal indicator bacteria (fecal coliform and Escherichia [E.] coli), and the physical and chemical indicators of water quality (relative to Texas Surface Water Quality Standards), in streams receiving discharge from DFW Airport and vicinity. At sampling sites in the lower West Fork Trinity River watershed during low-flow conditions, geometric mean E. coli counts for five of the eight West Fork Trinity River watershed sampling sites exceeded the Texas Commission on Environmental Quality E. coli criterion, thus not fully supporting contact recreation. Two of the five sites with geometric means that exceeded the contact recreation criterion are airport discharge sites, which here means that the major fraction of discharge at those sites is from DFW Airport. At sampling sites in the Elm Fork Trinity River watershed during low-flow conditions, geometric mean E. coli counts exceeded the geometric mean contact recreation criterion for seven (four airport, three non-airport) of 13 sampling sites. Under low-flow conditions in the lower West Fork Trinity River watershed, E. coli counts for airport discharge sites were significantly different from (lower than) E. coli counts for non-airport sites. Under low-flow conditions in the Elm Fork Trinity River watershed, there was no significant difference between E. coli counts for airport sites and non-airport sites. During stormflow conditions, fecal indicator bacteria counts at the most downstream (integrator) sites in each watershed were considerably higher than counts at those two sites during low-flow conditions. When stormflow sample counts are included with low-flow sample counts to compute a geometric mean for each site, classification changes from fully supporting to not fully supporting contact recreation on the basis of the geometric mean contact recreation criterion. All water temperature measurements at sampling sites in the lower West Fork Trinity River watershed were less than the maximum criterion for water temperature for the lower West Fork Trinity segment. Of the measurements at sampling sites in the Elm Fork Trinity River watershed, 95 percent were less than the maximum criterion for water temperature for the Elm Fork Trinity River segment. All dissolved oxygen concentrations were greater than the minimum criterion for stream segments classified as exceptional aquatic life use. Nearly all pH measurements were within the pH criterion range for the classified segments in both watersheds, except for those at one airport site. For sampling sites in the lower West Fork Trinity River watershed, all annual average dissolved solids concentrations were less than the maximum criterion for the lower West Fork Trinity segment. For sampling sites in the Elm Fork Trinity River, nine of the 13 sites (six airport, three non-airport) had annual averages that exceeded the maximum criterion for that segment. For ammonia, 23 samples from 12 different sites had concentrations that exceeded the screening level for ammonia. Of these 12 sites, only one non-airport site had more than the required number of exceedances to indicate a screening level concern. Stormflow total suspended solids concentrations were significantly higher than low-flow concentrations at the two integrator sites. For sampling sites in the lower West Fork Trinity River watershed, all annual average chloride concentrations were less than the maximum annual average chloride concentration criterion for that segment. For the 13 sampling sites in the Elm Fork Trinity River watershed, one non-airport site had an annual average concentration that exceeded the maximum annual average chloride concentration criterion for that segment.

[Kinetics of uptake of phosphates and nitrates by marine multicellular algae Gelidium latifolium (Grev.) Born. et Thur].

PubMed

Silkin, V A; Chubchikova, I N

2007-01-01

We studied nonstationary kinetics of the uptake of phosphates and nitrates by the red marine algae Gelidium latifolium (Grev.) Born et Thur. and calculated constants of the Michaelis-Menten equation for these elements. In the area of 0-3 microM, the kinetics of phosphate consumption had the following coefficients: maximum rate of uptake 0.8 micromol/(g x h), constant of half-saturation 1.745 microM. For nitrate nitrogen at 0-30 microM, an adaptive strategy of uptake kinetics was noted with change of the equation parameters with time: after 1 h, the maximum rate of uptake was 5.1 micromol/(g x h) and constant of half-saturation 19 gM, while within 2 h, the maximum rate of uptake significantly increased. This could be related to the synthesis of nitrate reductase. Coupled with the uptake of nitrates, nonstationary kinetics of the release of nitrates in the surrounding medium had a one-peak pattern: the maximum concentration of nitrites in the medium and the time of its achievement increased with the initial concentration of nitrates. The maximum concentration of nitrites was 6 to 14% of the initial concentration in the medium.

Uranium hydrogeochemical and stream sediment reconnaissance data from the area of the Shishmaref, Kotzebue, Selawik and Shungnak Quadrangles, northern Seward Peninsula and vicinity, Alaska

DOE Office of Scientific and Technical Information (OSTI.GOV)

Warren, R.G.; Hill, D.E.; Sharp, R.R. Jr.

1978-05-01

During the summer of 1976, 1336 water and 1251 sediment samples were collected for Los Alamos Scientific Laboratory (LASL) from 1356 streams and small lakes or ponds within Shishmaref, Kotzebue, Selawik, and western portion of Shungnak NTMS quadrangles in western Alaska. Both a water and sediment sample were generally obtained from each location at a nominal location density of 1/23 km/sup 2/. Total uranium was measured in waters by fluorometry and in sediments and a few waters by delayed neutron counting at LASL. Uranium concentrations in waters have a mean of 0.31 ppB and a maximum of 9.23 ppB, andmore » sediments exhibit a mean of 3.44 ppM and a maximum of 37.7 ppM. A large number of high-uranium concentrations occur in both water and sediment samples collected in the Selawik Hills. At least two locations within the Selawik Hills appear favorable for further investigation of possible uranium mineralization. A cluster of high-uranium sediments, seen in the Waring Mountains, are probably derived from a lower Cretaceous conglomerate unit which is assocated with known airborne radiometric anomalies. Apparently less favorable areas for further investigation of possible uranium mineralization are also located in the Waring Mountains and Kiana Hills. Additional samples were collected within the Shungnak quadrange to increase the sampling density used elsewhere in the area to about one location per 11 km/sup 2/ (double-density). Contoured plots of uranium concentrations for both waters and sediments were prepared for all double-density sample locations, and then for the even-numbered and odd-numbered locations separately. These plots indicate that the HSSR sampling density of 1/23 km/sup 2/ used in lowland areas of Alaska provide essentially the same definition of relative areal uranium distributions in waters and sediments as seen when the density is doubled. These plots indicate that regional distribution patterns for uranium are well defined without selective sampling of geologic units.« less

Natural convection heat transfer in water near its density maximum

NASA Astrophysics Data System (ADS)

Yen, Yin-Chao

1990-12-01

This monograph reviews and summarizes to date the experimental and analytical results on the effect of water density near its maximum convection, transient flow and temperature structure characteristics: (1) in a vertical enclosure; (2) in a vertical annulus; (3) between horizontal concentric cylinders; (4) in a square enclosure; (5) in a rectangular enclosure; (6) in a horizontal layer; (7) in a circular confined melt layer; and (8) in bulk water during melting. In a layer of water containing a maximum density temperature of 4 C, the onset of convection (the critical number) is found not to be a constant value as in the classical normal fluid but one that varies with the imposed thermal and hydrodynamic boundaries. In horizontal layers, a nearly constant temperature zone forms and continuously expands between the warm and cold boundaries. A minimum heat transfer exists in most of the geometries studied and, in most cases, can be expressed in terms of a density distribution parameter. The effect of this parameter on a cells formation, disappearance and transient structure is discussed, and the effect of split boundary flow on heat transfer is presented.

Levels of total mercury in predatory fish sold in Canada in 2005.

PubMed

Dabeka, R W; McKenzie, A D; Forsyth, D S

2011-06-01

Total mercury was analysed in 188 samples of predatory fish purchased at the retail level in Canada in 2005. The average concentrations (ng g(-1), range) were: sea bass 329 (38-1367), red snapper 148 (36-431), orange roughy 543 (279-974), fresh water trout 55 (20-430), grouper 360 (8-1060), black cod 284 (71-651), Arctic char 37 (28-54), king fish 440 (42-923), tilefish 601 (79-1164) and marlin 854 (125-2346). The Canadian standard for maximum total mercury allowed in the edible portions of fish sold at the retail level is 1000 ng g(-1) for shark, swordfish, marlin, orange roughy, escolar and both fresh and frozen tuna. The standard is 500 ng g(-1) for all other types of fish. In this study, despite the small number of samples of each species, the 1000 ng g(-1) maximum was exceeded in five samples of marlin (28%). The 500 ng g(-1) maximum was exceeded by six samples of sea bass (20%), four of tilefish (50%), five of grouper (24%), six of king fish (40%) and one of black cod (13%).

[Hydroxylamine conversion by anammox enrichment].

PubMed

Hu, Anhui; Zheng, Ping; Lu, Huifeng; Ding, Shuang; Wang, Caihua

2010-04-01

Hydroxylamine is an important intermediate product of anammox. This study was focused on the characteristics of hydroxylamine and nitrite conversions by anammox enrichment. The changes of nitrogenous substrates and related products with time were measured using batch tests with anammox enrichment as inoculum. Since hydroxylamine didn't react with nitrite in uninoculated control culture, these two compounds were chemically stable. Both of them decreased with time in anammox enrichment inoculated cultures, in which ammonia as intermediate product would be produced and converted with the maximum concentration being 0.338 mg/L. The total nitrogen concentration decreased from 4.694 mmol/L to 0.812 mmol/L with conversion rate 82.7% in the end. When hydroxylamine and nitrite concentrations were about 2.5 mmol/L respectively, the maximum specific sludge conversion rates of hydroxylamine was 0.535 mmol/(gVSS.h), which was 1.81 times bigger than that of ammonia in ammonia reaction system; the maximum specific sludge rate of total nitrogen was slightly higher than that in ammonia reaction system. When hydroxylamine concentration increased to 5.0 mmol/L, the hydroxylamine and nitrite conversion rates promoted by 26.7% and 120.7% respectively; and the maximum ammonia accumulated was 1.810 mmol/L. When nitrite concentration increased to 5.0 mmol/L, the hydroxylamine and nitrite conversion rates promoted by 6.9% and 9.0% respectively; and the maximum ammonia accumulated was 0.795 mmol/L. Anammox enrichment was capable of converting hydroxylamine and nitrite simultaneously and had the higher conversion rate of hydroxylamine than ammonia conversion rate. Hydroxylamine and nitrite conversion rates were less affected by increase in nitrite concentration, but more significantly influenced by increase in hydroxylamine. The maximum ammonia concentration accumulated would rise as the result of increasing both hydroxylamine and nitrite. The result of experiment was consistent with pathway model presented by van de Graaf AA.

[Electricity generation using high concentration terephthalic acid solution by microbial fuel cell].

PubMed

Ye, Ye-Jie; Song, Tian-Shun; Xu, Yuan; Chen, Ying-Wen; Zhu, She-Min; Shen, Shu-Bao

2009-04-15

The high concentration terephthalic acid (TA) solution as the substrate of microbial fuel cell (MFC) was studied to generate electricity. The open circuit voltage was 0.54 V after inoculating for 210 h with anaerobic activated sludge, which proved that TA can be the substrate of microbial fuel cell to generate electricity. The influence of pH and substrate concentration on generating electricity was studied deeply. The voltage output of external resistance (R = 1,000 Omega) was the highest when pH was 8.0. It increased as the substrate concentration increasing and tended towards a maximum value. The maximum voltage output Umax was 0.5 V and Ks was 785.2 mg/L by Monod equation regression. When the substrate concentration (according to COD) was 4000 mg/L, the maximum power density was 96.3 mW/m2, coulomb efficiency was 2.66% and COD removal rate was 80.3%.

[Up-conversion luminescent materials of Y2O3: RE(RE=Er or Er/Yb) prepared by sol-gel combustion synthesis].

PubMed

Han, Peng-de; Zhang, Le; Huang, Xiao-gu; Wang, Li-xi; Zhang, Qi-tu

2010-11-01

Y2O3 powders doped with rare-earth ions were synthesized by sol-gel combustion synthesis. Effects of different calcinating temperatures, Er+ doping concentration and Yb3+ doping concentration were investigated. It was shown that the single well crystallized Y2O3 powders could be obtained at 800 degrees C; as the calcinating temperature increased, the crystallinity and upconversion luminescence intensity were higher; the particle size was uniform around 1 microm at 900 degrees C; when Er3+ doping concentration was 1 mol%, the green upconversion luminescence intensity reached the maximum, but for red upconversion luminescence, when Er3+ doping concentration was 4 mol%, its luminescence intensity reached the maximum; as the ratio of Yb3+ to Er3+ was 4:1, the green emission intensity reached the maximum, while the red emission intensity was always increasing as Yb3+ doping concentration increased.

The effectiveness of water-treatment systems for arsenic used in 11 homes in Southwestern and Central Ohio, 2013

USGS Publications Warehouse

Thomas, Mary Ann; Ekberg, Mike

2016-02-23

In 2013, the U.S. Geological Survey and the Miami Conservancy District investigated the effectiveness of methods used to remove arsenic from drinking water at 11 homes in southwestern and central Ohio. The untreated (raw) ground-water had arsenic concentrations of 7.7–382 micrograms per liter (µg/L), and the median concentration was 30 µg/L. The pH was neutral to slightly alkaline, and redox conditions were strongly reducing, as indicated by high concentrations of iron. The predominant arsenic species was arsenite (As3+), which is difficult to treat because it exists in water as an uncharged compound (H3AsO3).The water-treatment systems included (1) seven single-tap reverse-osmosis systems, (2) two whole-house oxidation/filtration systems, and (3) two systems that included wholehouse anion exchange and single-tap reverse osmosis. All but one system included pretreatment by a water softener, and two systems included preoxidation to convert arsenite (As3+) to arsenate (As5+) before treatment by anion exchange.None of the treatment systems removed all of the arsenic from the drinking water. About one-half of the systems decreased the arsenic concentration to less than the maximum contamination level of 10 µg/L. The effectiveness of the systems varied widely; the percentage of arsenic removed ranged from 2 to 90 percent, and the median was 65 percent.At some sites, the low effectiveness of arsenic removal may have been related to system maintenance and(or) operation issues. At two sites, homeowners acknowledged that the treatment systems had not been maintained for several years. At two other sites, the treatment systems were being maintained, but the water-quality data indicated that one of the components was not working, unbeknownst to the homeowner. EPA research at a small number of sites in Ohio indicated that operation and maintenance of some arsenic-treatment systems was not always simple.Another factor that affected system effectiveness was the quality of the raw water. In general, the treatment systems were less effective at treating higher concentrations of arsenic. For five sites with raw-water arsenic concentrations of 10–30 µg/L, the systems removed 65–81 percent of the arsenic, and the final concentrations were less than the maximum contamination level. For three sites with higher raw-water arsenic concentrations (50–75 µg/L), the systems removed 22–34 percent of the arsenic; and the final concentrations were 4–5 times more than the maximum contamination level. Other characteristics of the raw water may have affected the performance of treatment systems; in general, raw water with the higher arsenic concentrations also had higher pH, higher concentrations of organic carbon and ammonia, and more reducing (methanogenic) redox conditions.For sites with raw-water arsenic concentrations of 10–30 µg/L, two types of systems (reverse osmosis and oxidation/filtration) removed similar amounts of arsenic, but the quality of the treated water differed in other respects. Reverse osmosis caused substantial decreases in pH, alkalinity, and concentrations of most ions. On the other hand, oxidation/filtration using manganese-based media caused a large increase of manganese concentrations, from less than 50 µg/L in raw water to more than 700 µg/L in outflow from the oxidation filtration units.It is not known if the results of this study are widely applicable; the number of systems sampled was relatively small, and each system was sampled only once. Further study may be warranted to investigate whether available methods of arsenic removal are effective/practical for residential use in areas like Ohio, were groundwater with elevated arsenic concentrations is strongly reducing, and the predominant arsenic species is arsenite (As3+).

An investigation of FT-Raman spectroscopy for quantification of additives to milk

USDA-ARS?s Scientific Manuscript database

In this research, four chemicals, urea, ammonium sulfate, dicyandiamide, and melamine, were mixed into liquid nonfat milk at concentrations starting from 0.1% to a maximum concentration determined for each chemical according to its maximum solubility, and two Raman spectrometers—a commercial Nicolet...

21 CFR 173.370 - Peroxyacids.

Code of Federal Regulations, 2010 CFR

2010-04-01

... conditions: (a) The additive is a mixture of peroxyacetic acid, octanoic acid, acetic acid, hydrogen peroxide... the maximum concentration of hydrogen peroxide is 75 ppm. (2) The additive is used as an antimicrobial... million (ppm) as peroxyacetic acid, the maximum concentration of hydrogen peroxide is 110 ppm, and the...

21 CFR 173.370 - Peroxyacids.

Code of Federal Regulations, 2011 CFR

2011-04-01

... conditions: (a) The additive is a mixture of peroxyacetic acid, octanoic acid, acetic acid, hydrogen peroxide... the maximum concentration of hydrogen peroxide is 75 ppm. (2) The additive is used as an antimicrobial... million (ppm) as peroxyacetic acid, the maximum concentration of hydrogen peroxide is 110 ppm, and the...

40 CFR 464.34 - New source performance standards.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-continuous dischargers, annual average mass standards and maximum day and maximum for monthly average concentration (mg/l) standards shall apply. Concentration standards and annual average mass standards shall only... 40 Protection of Environment 31 2012-07-01 2012-07-01 false New source performance standards. 464...

40 CFR 464.34 - New source performance standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-continuous dischargers, annual average mass standards and maximum day and maximum for monthly average concentration (mg/l) standards shall apply. Concentration standards and annual average mass standards shall only... 40 Protection of Environment 30 2014-07-01 2014-07-01 false New source performance standards. 464...

40 CFR 464.34 - New source performance standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-continuous dischargers, annual average mass standards and maximum day and maximum for monthly average concentration (mg/l) standards shall apply. Concentration standards and annual average mass standards shall only... 40 Protection of Environment 31 2013-07-01 2013-07-01 false New source performance standards. 464...

[Electricity generation from sweet potato fuel ethanol wastewater using microbial fuel cell technology].

PubMed

Cai, Xiao-Bo; Yang, Yi; Sun, Yan-Ping; Zhang, Liang; Xiao, Yao; Zhao, Hai

2010-10-01

Air cathode microbial fuel cell (MFC) were investigated for electricity production from sweet potato fuel ethanol wastewater containing 5000 mg/L of chemical oxygen demand (COD). Maximum power density of 334.1 mW/m2, coulombic efficiency (CE) of 10.1% and COD removal efficiency of 92.2% were approached. The effect of phosphate buffer solution (PBS) and COD concentration on the performance of MFC was further examined. The addition of PBS from 50 mmol/L to 200 mmol/L increased the maximum power density and CE by 33.4% and 26.0%, respectively. However, the COD removal efficiency was not relative to PBS concentration in the wastewater. When the COD increased from 625 mg/L to 10 000 mg/L, the maximum value of COD removal efficiency and the maximum power density were gained at the wastewater strength of 5 000 mg/L. But the CE ranged from 28.9% to 10.3% with a decreasing trend. These results demonstrate that sweet potato fuel ethanol wastewater can be used for electricity generation in MFC while at the same time achieving wastewater treatment. The increasing of PBS concentration can improve the power generation of MFC. The maximum power density of MFC increases with the rise of COD concentration, but the electricity generation will decrease for the acidification of high wastewater concentration.

The lasting effect of limonene-induced particle formation on air quality in a genuine indoor environment.

PubMed

Rösch, Carolin; Wissenbach, Dirk K; von Bergen, Martin; Franck, Ulrich; Wendisch, Manfred; Schlink, Uwe

2015-09-01

Atmospheric ozone-terpene reactions, which form secondary organic aerosol (SOA) particles, can affect indoor air quality when outdoor air mixes with indoor air during ventilation. This study, conducted in Leipzig, Germany, focused on limonene-induced particle formation in a genuine indoor environment (24 m(3)). Particle number, limonene and ozone concentrations were monitored during the whole experimental period. After manual ventilation for 30 min, during which indoor ozone levels reached up to 22.7 ppb, limonene was introduced into the room at concentrations of approximately 180 to 250 μg m(-3). We observed strong particle formation and growth within a diameter range of 9 to 50 nm under real-room conditions. Larger particles with diameters above 100 nm were less affected by limonene introduction. The total particle number concentrations (TPNCs) after limonene introduction clearly exceed outdoor values by a factor of 4.5 to 41 reaching maximum concentrations of up to 267,000 particles cm(-3). The formation strength was influenced by background particles, which attenuated the formation of new SOA with increasing concentration, and by ozone levels, an increase of which by 10 ppb will result in a six times higher TPNC. This study emphasizes indoor environments to be preferred locations for particle formation and growth after ventilation events. As a consequence, SOA formation can produce significantly higher amounts of particles than transported by ventilation into the indoor air.

Summary of airborne chlorine and hydrogen chloride gas measurements for August 20 and September 5, 1977 Voyager launches at Air Force Eastern Test Range, Florida

NASA Technical Reports Server (NTRS)

Gregory, G. L.; Emerson, B. R., Jr.; Hudgins, C. H.

1978-01-01

Airborne chlorine and hydrogen chloride measurements were made in the tropospheric ground cloud following the Voyager launches of August 20 and September 5, 1977. The maximum observed hydrogen chloride concentration for both launches was about 25 to 30 parts per million (ppm) occurring typically 2 to 6 minutes after launch. By completion of the sampling mission (1-1/2 hours for August, 4-1/2 hours for September), the maximum in-cloud concentration decayed to about 1 to 2 ppm. Maximum observed chlorine concentrations were about 40 to 55 parts per billion (ppb) about 2 to 8 minutes after launch; by about 15 minutes after launch, chlorine concentrations were less than 10 ppb (detection limit). In-cloud chlorine concentrations were well below 1 percent of hydrogen chloride concentrations. The appendix of the report discusses the chlorine instrument and the laboratory evaluation of the detector.

Development of a guideline on vegetation area to reduce the risk of weed pollinosis in Korea

NASA Astrophysics Data System (ADS)

Rang Kim, Kyu; Lee, Hye-Rim; Kim, Mijin; Baek, Won-ki; Oh, Jae-Won; Choi, Young-Jean; Jung, Hyun-Sook

2013-04-01

Allergenic pollens are influenced by the environmental conditions so that the daily number of pollens varies by temperature, humidity, wind speed, etc. The relationship between the daily pollens and meteorological conditions were determined and utilized to forecast daily risk level of pollen allergy in Korea. Another important factor for the daily risk level of pollens is the vegetation area of the allergenic plants. In this study, the relationship between the area and pollen concentration was identified for two major weed species: Ragweed and Japanese Hop. It was then utilized to determine the upper limit of vegetation area to confine the risk level to a certain degree in the field. Three sites with different levels of pollen concentration were selected among twelve pollen observation sites in Korea based on the historical observation of the weed pollens. The vegetation area of the two weed species within four square kilometers at each site was surveyed. The maximum daily pollen concentration was highly correlated with the vegetation area and it was selected as a dependent variable for the regression equations, which were used as the guideline for vegetation area. According to the guideline, to limit the maximum daily pollen concentration under the moderate risk level or less than 50 pollen grains per cubic meter for Ragweed, the vegetation area should remain less than 0.6% of the ground area. For the moderate risk of Japanese Hop, pollen grains should be limited less than 100 and the area be less than 0.4%.

Faces of a changing climate: semi-quantitative multi-mycotoxin analysis of grain grown in exceptional climatic conditions in Norway.

PubMed

Uhlig, Silvio; Eriksen, Gunnar Sundstøl; Hofgaard, Ingerd Skow; Krska, Rudolf; Beltrán, Eduardo; Sulyok, Michael

2013-09-27

Recent climatological research predicts a significantly wetter climate in Southern Norway as a result of global warming. Thus, the country has already experienced unusually wet summer seasons in the last three years (2010-2012). The aim of this pilot study was to apply an existing multi-analyte LC-MS/MS method for the semi-quantitative determination of 320 fungal and bacterial metabolites in Norwegian cereal grain samples from the 2011 growing season. Such knowledge could provide important information for future survey and research programmes in Norway. The method includes all regulated and well-known mycotoxins such as aflatoxins, trichothecenes, ochratoxin A, fumonisins and zearalenone. In addition, a wide range of less studied compounds are included in the method, e.g., Alternaria toxins, ergot alkaloids and other metabolites produced by fungal species within Fusarium, Penicillium and Aspergillus. Altogether, 46 metabolites, all of fungal origin, were detected in the 76 barley, oats and wheat samples. The analyses confirmed the high prevalence and relatively high concentrations of type-A and -B trichothecenes (e.g., deoxynivalenol up to 7230 µg/kg, HT-2 toxin up to 333 µg/kg). Zearalenone was also among the major mycotoxins detected (maximum concentration 1670 µg/kg). Notably, several other Fusarium metabolites such as culmorin, 2-amino-14,16-dimethyloctadecan-3-ol and avenacein Y were co-occurring. Furthermore, the most prevalent Alternaria toxin was alternariol with a maximum concentration of 449 µg/kg. A number of Penicillium and Aspergillus metabolites were also detected in the samples, e.g., sterigmatocystin in concentrations up to 20 µg/kg.

Relationships between salivary testosterone and cortisol concentrations and training performance in Olympic weightlifters.

PubMed

Crewther, B T; Christian, Cook

2010-09-01

This study examined the relationships between salivary testosterone (Sal-T) and cortisol (Sal-C) concentrations and training performance in Olympic weightlifters. Four male and four female Olympic weightlifters each provided saliva samples before and after four workouts during a four-week training period. Training involved the same three exercises; snatch, clean and jerk, and front squat with the one repetition maximum (1RM) calculated for each exercise during each workout. Significant (P < 0.05-0.01) training improvements in 1RM performance (4.0-5.2%) were noted during the snatch and clean and jerk exercises, along with the Olympic total lift. For male participants only, the pre-workout concentrations of Sal T were significantly (P < 0.05-0.01) correlated with the snatch (r = 0.70) and clean and jerk 1RM (r = 0.62), and the Olympic total lift (r = 0.66). A short period of training improved the 1RM performance of Olympic weightlifters in two exercises (snatch and clean and jerk) and the Olympic total. For male participants, their Sal-T concentrations before each workout was also related to 1RM performance during these exercises, thereby highlighting one possible short-term causative mechanism. Limitations of this study include the short duration of hormonal monitoring, the limited number of workouts assessed and the small number of participants recruited. Also, correlations between the outcome variables still only reflect casual associations.

Experimental validation of energy parameters in parabolic trough collector with plain absorber and analysis of heat transfer enhancement techniques

NASA Astrophysics Data System (ADS)

Bilal, F. R.; Arunachala, U. C.; Sandeep, H. M.

2018-01-01

The quantum of heat loss from the receiver of the Parabolic Trough Collector is considerable which results in lower thermal efficiency of the system. Hence heat transfer augmentation is essential which can be attained by various techniques. An analytical model to evaluate the system with bare receiver performance was developed using MATLAB. The experimental validation of the model resulted in less than 5.5% error in exit temperature using both water and thermic oil as heat transfer fluid. Further, heat transfer enhancement techniques were incorporated in the model which included the use of twisted tape inserts, nanofluid, and a combination of both for further enhancement. It was observed that the use of evacuated glass cover in the existing setup would increase the useful heat gain up to 5.3%. Fe3O4/H2O nanofluid showed a maximum enhancement of 56% in the Nusselt number for the volume concentration of 0.6% at highest Reynolds number. Similarly, twisted tape turbulators (with twist ratio of 2) taken alone with water exhibited 59% improvement in Nusselt number. Combining both the heat transfer augmentation techniques at their best values revealed the Nusselt number enhancement up to 87%. It is concluded that, use of twisted tape with water is the best method for heat transfer augmentation since it gives the maximum effective thermal efficiency amongst all for the range of Re considered. The first section in your paper

30 CFR 57.5039 - Maximum permissible concentration.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Maximum permissible concentration. 57.5039 Section 57.5039 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Air Quality, Radiation, Physical Agents, and Diesel...

30 CFR 57.5039 - Maximum permissible concentration.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Maximum permissible concentration. 57.5039 Section 57.5039 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Air Quality, Radiation, Physical Agents, and Diesel...

30 CFR 57.5039 - Maximum permissible concentration.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Maximum permissible concentration. 57.5039 Section 57.5039 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Air Quality, Radiation, Physical Agents, and Diesel...

30 CFR 57.5039 - Maximum permissible concentration.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Maximum permissible concentration. 57.5039 Section 57.5039 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Air Quality, Radiation, Physical Agents, and Diesel...

30 CFR 57.5039 - Maximum permissible concentration.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Maximum permissible concentration. 57.5039 Section 57.5039 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Air Quality, Radiation, Physical Agents, and Diesel...

40 CFR Table 1 to Subpart A of... - Maximum Concentration of Constituents for Groundwater Protection

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 25 2014-07-01 2014-07-01 false Maximum Concentration of Constituents for Groundwater Protection 1 Table 1 to Subpart A of Part 192 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) RADIATION PROTECTION PROGRAMS HEALTH AND ENVIRONMENTAL PROTECTION STANDARDS FOR...

Forecasting of the selected features of Poaceae (R. Br.) Barnh., Artemisia L. and Ambrosia L. pollen season in Szczecin, north-western Poland, using Gumbel's distribution.

PubMed

Puc, Małgorzata; Wolski, Tomasz

2013-01-01

The allergenic pollen content of the atmosphere varies according to climate, biogeography and vegetation. Minimisation of the pollen allergy symptoms is related to the possibility of avoidance of large doses of the allergen. Measurements performed in Szczecin over a period of 13 years (2000-2012 inclusive) permitted prediction of theoretical maximum concentrations of pollen grains and their probability for the pollen season of Poaceae, Artemisia and Ambrosia. Moreover, the probabilities were determined of a given date as the beginning of the pollen season, the date of the maximum pollen count, Seasonal Pollen Index value and the number of days with pollen count above threshold values. Aerobiological monitoring was conducted using a Hirst volumetric trap (Lanzoni VPPS). Linear trend with determination coefficient (R(2)) was calculated. Model for long-term forecasting was performed by the method based on Gumbel's distribution. A statistically significant negative correlation was determined between the duration of pollen season of Poaceae and Artemisia and the Seasonal Pollen Index value. Seasonal, total pollen counts of Artemisia and Ambrosia showed a strong and statistically significant decreasing tendency. On the basis of Gumbel's distribution, a model was proposed for Szczecin, allowing prediction of the probabilities of the maximum pollen count values that can appear once in e.g. 5, 10 or 100 years. Short pollen seasons are characterised by a higher intensity of pollination than long ones. Prediction of the maximum pollen count values, dates of the pollen season beginning, and the number of days with pollen count above the threshold, on the basis of Gumbel's distribution, is expected to lead to improvement in the prophylaxis and therapy of persons allergic to pollen.

Level of endogenous formaldehyde in maple syrup as determined by spectrofluorimetry.

PubMed

Lagacé, Luc; Guay, Stéphane; Martin, Nathalie

2003-01-01

The level of endogenous formaldehyde in maple syrup was established from a large number (n = 300) of authentic maple syrup samples collected during 2000 and 2001 in the province of Quebec, Canada. The average level of formaldehyde from these authentic samples was measured at 0.18 mg/kg in 2000 and 0.28 mg/kg in 2001, which is lower than previously published. These average values can be attributed to the improved spectrofluorimetric method used for the determination. However, the formaldehyde values obtained demonstrate a relatively large distribution with maximums observed at 1.04 and 1.54 mg/kg. These values are still under the maximum tolerance level of 2.0 mg/kg paraformaldehyde pesticide residue. Extensive heat treatment of maple syrup samples greatly enhanced the formaldehyde concentration of the samples, suggesting that extensive heat degradation of the sap constituents during evaporation could be responsible for the highest formaldehyde values in maple syrup.

Concentrations of heavy metals in marine wild fishes captured from the southern sea of Korea and associated health risk assessments

NASA Astrophysics Data System (ADS)

Hwang, Dong-Woon; Kim, Seong-Soo; Kim, Seong-Gil; Kim, Dong-Sun; Kim, Tae-Hoon

2017-12-01

Concentrations of heavy metals (As, Cd, Cr, Cu, Hg, Pb, and Zn) were determined in edible parts (muscle) of 34 marine wild fish caught from the southern sea of Korea in 2007 and 2008 in order to understand the accumulation pattern of heavy metals in wild fish and to assess the potential health risk posed by fish consumption. The highest concentrations in the muscle of 17 pelagic and 17 demersal fishes were Zn and As, respectively, while the lowest concentration in both fishes was Cd. The mean concentrations of all metals except As in wild fish were much lower than the regulatory limits for fish and fishery products applied in a number of countries. Unlike other metals, As concentration in wild fish of this study region was relatively higher than that found in other country. Estimated daily intake (EDI) of the metals was in the range of 0.05% to 22.5% of the provisional maximum tolerable daily intakes (PMTDI). Similarly, the target hazard quotient (THQ) was below 1.0 for each metal. These results imply that the consumption of the investigated wild fish do not cause significant adverse health effects.

Gauging the Nearness and Size of Cycle Maximum

NASA Technical Reports Server (NTRS)

Wilson, Robert M.; Hathaway, David H.

2003-01-01

A simple method for monitoring the nearness and size of conventional cycle maximum for an ongoing sunspot cycle is examined. The method uses the observed maximum daily value and the maximum monthly mean value of international sunspot number and the maximum value of the 2-mo moving average of monthly mean sunspot number to effect the estimation. For cycle 23, a maximum daily value of 246, a maximum monthly mean of 170.1, and a maximum 2-mo moving average of 148.9 were each observed in July 2000. Taken together, these values strongly suggest that conventional maximum amplitude for cycle 23 would be approx. 124.5, occurring near July 2002 +/-5 mo, very close to the now well-established conventional maximum amplitude and occurrence date for cycle 23-120.8 in April 2000.

Assessment of Potential Health Hazards During Emission of Hydrogen Sulphide from the Mine Exploiting Copper Ore Deposit - Case Study.

PubMed

Kupczewska-Dobecka, Małgorzata; Czerczak, Sławomir; Gromiec, Jan P; Konieczko, Katarzyna

2015-06-01

The aim of this study was to determine hydrogen sulphide concentration emitted from the mine extracting copper ore, to evaluate potential adverse health effects to the population living in four selected villages surrounding the exhaust shaft. Maximum measured concentration of hydrogen sulphide in the emitter is 286 µg/m³. Maximum emission calculated from the results of determinations of concentrations in the emitter is 0.44 kg/h. In selected villages hydrogen sulphide at concentrations exceeding 4 µg/m³ was not detected in any of the 5-hour air samples. In all locations, the estimated maximum 1-hour concentrations of hydrogen sulphide were below 1 µg/m³, and the estimated mean annual concentrations were below 0.53 µg/m³. Any risk to the health of people in the selected area is not expected. As indicated by the available data on the threshold odour, the estimated concentrations of hydrogen sulphide may be sensed by humans. Copyright© by the National Institute of Public Health, Prague 2015.

Pesticides in Water and Suspended Sediment of the Alamo and New Rivers, Imperial Valley/Salton Sea Basin, California, 2006-2007

USGS Publications Warehouse

Orlando, James L.; Smalling, Kelly L.; Kuivila, Kathryn

2008-01-01

Water and suspended-sediment samples were collected at eight sites on the Alamo and New Rivers in the Imperial Valley/Salton Sea Basin of California and analyzed for both current-use and organochlorine pesticides by the U.S. Geological Survey. Samples were collected in the fall of 2006 and spring of 2007, corresponding to the seasons of greatest pesticide use in the basin. Large-volume water samples (up to 650 liters) were collected at each site and processed using a flow-through centrifuge to isolate suspended sediments. One-liter water samples were collected from the effluent of the centrifuge for the analysis of dissolved pesticides. Additional samples were collected for analysis of dissolved organic carbon and for suspended-sediment concentrations. Water samples were analyzed for a suite of 61 current-use and organochlorine pesticides using gas chromatography/mass spectrometry. A total of 25 pesticides were detected in the water samples, with seven pesticides detected in more than half of the samples. Dissolved concentrations of pesticides observed in this study ranged from below their respective method detection limits to 8,940 nanograms per liter (EPTC). The most frequently detected compounds in the water samples were chlorpyrifos, DCPA, EPTC, and trifluralin, which were observed in more than 75 percent of the samples. The maximum concentrations of most pesticides were detected in samples from the Alamo River. Maximum dissolved concentrations of carbofuran, chlorpyrifos, diazinon, and malathion exceeded aquatic life benchmarks established by the U.S. Environmental Protection Agency for these pesticides. Suspended sediments were analyzed for 87 current-use and organochlorine pesticides using microwave-assisted extraction, gel permeation chromatography for sulfur removal, and either carbon/alumina stacked solid-phase extraction cartridges or deactivated Florisil for removal of matrix interferences. Twenty current-use pesticides were detected in the suspended-sediment samples, including pyrethroid insecticides and fungicides. Fourteen legacy organochlorine pesticides also were detected in the suspended-sediment samples. Greater numbers of current-use and organochlorine pesticides were observed in the Alamo River samples in comparison with the New River samples. Maximum concentrations of current-use pesticides in suspended-sediment samples ranged from below their method detection limits to 174 micrograms per kilogram (pendimethalin). Most organochlorine pesticides were detected at or below their method detection limits, with the exception of p,p'-DDE, which had a maximum concentration of 54.2 micrograms per kilogram. The most frequently detected current-use pesticides in the suspended-sediment samples were chlorpyrifos, permethrin, tetraconazole, and trifluralin, which were observed in more than 83 percent of the samples. The organochlorine degradates p,p'-DDD and p,p'-DDE were detected in all suspended-sediment samples.

Swimming Stroke Mechanical Efficiency and Physiological Responses of 100-m Backstroke with and without the use of paddles

PubMed Central

Messinis, Spilios; Beidaris, Nikos; Messinis, Spyros; Soultanakis, Helen; Botonis, Petros; Platanou, Theodoros

2014-01-01

The use of swimming aids during training contributes to greater swimming efficiency by the improvement of the swimming specific power of the athlete. The purpose of this study was to compare the swimming stroke technical characteristics and the physiological responses of swimming 100-m backstroke, with and without the use of paddles at maximum and sub-maximum intensities at the same swimming speed. Eight swimmers competing at the national level participated in this study. The measurements took place at 4 different sessions. At every session, each participant swam individually one 100-m backstroke swimming trial with or without paddles at the same speed and two levels of intensity (100% and 85% of maximum speed). The results revealed lower stroke length, greater stroke number and gliding length without the use of swimming paddles at both intensities. Blood lactate concentration (10.03±2.96 vs. 5.85±2.23 mmol/l) and Rating of Perceived Exertion (17.43±2.07 vs. 12±2.82) were greater without the use of swimming paddles only at 100% of maximum speed. Thus, swimming backstroke with paddles compared to unaided swimming, at a similar speed, showed a greater efficiency at maximal but not at sub-maximal intensity. PMID:25031685

Swimming Stroke Mechanical Efficiency and Physiological Responses of 100-m Backstroke with and without the use of paddles.

PubMed

Messinis, Spilios; Beidaris, Nikos; Messinis, Spyros; Soultanakis, Helen; Botonis, Petros; Platanou, Theodoros

2014-03-27

The use of swimming aids during training contributes to greater swimming efficiency by the improvement of the swimming specific power of the athlete. The purpose of this study was to compare the swimming stroke technical characteristics and the physiological responses of swimming 100-m backstroke, with and without the use of paddles at maximum and sub-maximum intensities at the same swimming speed. Eight swimmers competing at the national level participated in this study. The measurements took place at 4 different sessions. At every session, each participant swam individually one 100-m backstroke swimming trial with or without paddles at the same speed and two levels of intensity (100% and 85% of maximum speed). The results revealed lower stroke length, greater stroke number and gliding length without the use of swimming paddles at both intensities. Blood lactate concentration (10.03±2.96 vs. 5.85±2.23 mmol/l) and Rating of Perceived Exertion (17.43±2.07 vs. 12±2.82) were greater without the use of swimming paddles only at 100% of maximum speed. Thus, swimming backstroke with paddles compared to unaided swimming, at a similar speed, showed a greater efficiency at maximal but not at sub-maximal intensity.

Use of Pleurotus eous Strain P-31 Spent Mushroom Compost (SMC) as Soil Conditioner on the Growth and Yield Performance of Capsicum annuum L. and Solanum lycopersicon L. Seedlings under Greenhouse Conditions in Ghana

PubMed Central

Wiafe-Kwagyan, M; Odamtten, G T

2018-01-01

The objective of this study was to investigate the influence of spent mushroom compost of Pleurotus eous strain P-31 on the growth and yield performance of pepper and tomato seedlings under greenhouse conditions. Sandy loam soil was combined with different percentages of SMC to obtain the following combinations (0, 5, 10, 15, 20, 25 and 30) %. Lower concentrations SMC5, SMC10 and SMC15 promoted vegetative growth (plant height, leaf area, chlorophyll content, number of leaves and axillary branches) of the two test plants. Tomato seedlings grown in SMC10 recorded the highest plant height (50.3 ± 7.2cm); leaf area (378.8 ± 1.2cm2); number of floral buds (51) and flowers (28) whereas SMC5 recorded the highest chlorophyll content 34.1 ± 0.9CCI though SMC15 recorded the highest number of leaves (8). Tomato seedlings grown in SMC30 produced both the maximum number of fruits (8) with corresponding high weight (34.2 ± 7.7g). Pepper seedlings grown in lower concentrations (SMC5–15) recorded the highest plant heights (29.8–30.8cm), chlorophyll content (20.3CCI) and leaf area (53.5–66.2 cm2). Although the different combinations of sandy loam soil and SMC did not significantly (p ≥ 0.05) affect the number of axillary branches developed; different combinations significantly (p ≤ 0.05) affected the number of floral bud, flower and fruit, weight of fruits formed and value of each of these increased with increasing percentage of SMC. Pepper seedlings grown on SMC30 recorded the maximum number of floral buds (32.0 ± 3.6), number of flowers (19.4 ± 1.3), number of fruits (10.8 ± 1.2) and weight of fruits (31.9 ± 3.4g). Tomato seedlings raised on SMC100 (spent mushroom compost only) and soil only did not significantly (p ≥ 0.05) differ from each other however, was statistically significant (p ≤ 0.05) from amended sandy loam soil by all criteria investigated. The study shows that SMC provide favourable soil conditioners for the cultivation of fruits, vegetables and foliage crops as it improved growth and yield of tomato and pepper seedlings. PMID:29644023

Radiation-induced polymerization of glass-forming systems. IV. Effect of the homogeneity of polymerization phase and polymer concentration on temperature dependence of initial polymerization rate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaetsu, I.; Ito, A.; Hayashi, K.

1973-06-01

The effect of homogeneity of polymerization phase and monomer concentration on the temperature dependence of initial polymerization rate was studied in the radiation-induced radical polymerization of binary systems consisting of glass-forming monomer and solvent. In the polymerization of a completely homogeneous system such as HEMA-propylene glycol, a maximum and a minimum in polymerization rates as a function of temperature, characteristic of the polymerization in glass-forming systems, were observed for all monomer concentrations. However, in the heterogeneous polymerization systems such as HEMA-triacetin and HEMAisoamyl acetate, maximum and minimum rates were observed in monomer-rich compositions but not at low monomer concentrations. Furthermore,more » in the HEMA-dioctyl phthalate polymerization system, which is extremely heterogeneous, no maximum and minimum rates were observed at any monomer concentration. The effect of conversion on the temperature dependence of polymerization rate in homogeneous bulk polymerization of HEMA and GMA was investigated. Maximum and minimum rates were observed clearly in conversions less than 10% in the case of HEMA and less than 50% in the case of GMA, but the maximum and minimum changed to a mere inflection in the curve at higher conversions. A similar effect of polymer concentration on the temperature dependence of polymerization rate in the GMA-poly(methyl methacrylate) system was also observed. It is deduced that the change in temperature dependence of polymerization rate is attributed to the decrease in contribution of mutual termination reaction of growing chain radicals to the polymerization rate. (auth)« less

Sodium triflate decreases interaggregate repulsion and induces phase separation in cationic micelles.

PubMed

Lima, Filipe S; Cuccovia, Iolanda M; Buchner, Richard; Antunes, Filipe E; Lindman, Björn; Miguel, Maria G; Horinek, Dominik; Chaimovich, Hernan

2015-03-10

Dodecyltrimethylammonium triflate (DTATf) micelles possess lower degree of counterion dissociation (α), lower hydration, and higher packing of monomers than other micelles of similar structure. Addition of sodium triflate ([NaTf] > 0.05 M) to DTATf solutions promotes phase separation. This phenomenon is commonly observed in oppositely charged surfactant mixtures, but it is rare for ionic surfactants and relatively simple counterions. While the properties of DTATf have already been reported, the driving forces for the observed phase separation with added salt remain unclear. Thus, we propose an interpretation for the observed phase separation in cationic surfactant solutions. Addition of up to 0.03 M NaTf to micellar DTATf solutions led to a limited increase of the aggregation number, to interface dehydration, and to a progressive decrease in α. The viscosity of DTATf solutions of higher concentration ([DTATf] ≥ 0.06 M) reached a maximum with increasing [NaTf], though the aggregation number slightly increased, and no shape change occurred. We hypothesize that this maximum results from a decrease in interaggregate repulsion, as a consequence of increased ion binding. This reduction in micellar repulsion without simultaneous infinite micellar growth is, probably, the major driving force for phase separation at higher [NaTf].

Diffusional falsification of kinetic constants on Lineweaver-Burk plots.

PubMed

Ghim, Y S; Chang, H N

1983-11-07

The effect of mass transfer resistances on the Lineweaver-Burk plots in immobilized enzyme systems has been investigated numerically and with analytical approximate solutions. While Hamilton, Gardner & Colton (1974) studied the effect of internal diffusion resistances in planar geometry, our study was extended to the combined effect of internal and external diffusion in cylindrical and spherical geometries as well. The variation of Lineweaver-Burk plots with respect to the geometries was minimized by modifying the Thiele modulus and the Biot number with the shape factor. Especially for a small Biot number all the three Lineweaver-Burk plots fell on a single line. As was discussed by Hamilton et al. (1974), the curvature of the line for large external diffusion resistances was small enough to be assumed linear, which was confirmed from the two approximate solutions for large and small substrate concentrations. Two methods for obtaining intrinsic kinetic constants were proposed: First, we obtained both maximum reaction rate and Michaelis constant by fitting experimental data to a straight line where external diffusion resistance was relatively large, and second, we obtained Michaelis constant from apparent Michaelis constant from the figure in case we knew maximum reaction rate a priori.

Modelling of carrying capacity in National Park - Fru\\vska Gora (Serbia) case study

NASA Astrophysics Data System (ADS)

Vujko, Aleksandra; Plavša, Jovan; Petrović, Marko D.; Radovanović, Milan; Gajić, Tamara

2017-03-01

Negative effects of tourism development in a destination are usually the consequence of the high concentration of tourists, accommodation facilities and the activities that are practiced in a relatively restricted area. One of the most important measures to protect the areas is to calculate the maximum number of tourists that can simultaneously reside in a region, i.e. the determination of the carrying capacity. This paper outlines a method for determining carrying capacity based on zoning of environmental resources and zoning within a region. The paper argues for a return to the idea of identifying maximum appropriate number of users. The main hypothesis of the paper is based on the statement that the development of tourism in Fru\\vska Gora (Mountain) National Park in Northern Serbia must be in accordance with the basic principles of sustainability, including the determination of carrying capacity. The main research goal was to show the opinion of local residents about the uncontrolled development of tourism, and to determine the carrying capacity in four sports and recreational zones of the mountain. The carrying capacity of the area is calculated by Lavery and Stanev formulas.

Short communication: concentrations of nonesterified fatty acids and β-hydroxybutyrate in dairy cows are not well correlated during the transition period.

PubMed

McCarthy, M M; Mann, S; Nydam, D V; Overton, T R; McArt, J A A

2015-09-01

The objective was to use longitudinal data of blood nonesterified fatty acids (NEFA) and β-hydroxybutyrate (BHBA) concentrations to describe the relationship between NEFA and BHBA in dairy cows during the periparturient period. Blood NEFA and BHBA concentration data collected from d 21 prepartum to 21 postpartum for 269 multiparous Holstein cows were selected from 4 different studies carried out within our research groups. Overall, NEFA concentrations were increased beginning near parturition with a relatively steady elevation of NEFA through d 9, after which concentrations gradually decreased. Prepartum BHBA concentrations began to increase beginning several days before parturition, continued to increase during the first week after parturition, and remained elevated through d 21 postpartum. Of the 269 cows included in the data set, 117 cows (43.5%) had at least one postpartum hyperketonemic event (BHBA ≥1.2mmol/L), and 202 cows (75.1%) had at least one event of elevated postpartum NEFA concentrations (≥0.70mmol/L) between 3 and 21 d in milk. Area under the curve (AUC) was used to investigate relationships between metabolites over time. Overall, the correlations between transition period NEFA and BHBA AUC were weak. We detected a negative correlation between prepartum BHBA AUC and postpartum NEFA AUC (r=-0.26). A positive correlation existed between postpartum NEFA AUC and postpartum BHBA AUC; however, the correlation coefficient was low (r=0.26). Large variation was found between the day of maximum NEFA concentration within the first 21 d in milk and day of maximum BHBA concentration for the same period. The mean and median times of maximum NEFA concentration were 6.8 and 6 d, respectively, whereas the mean and median times of maximum BHBA were 9.6 and 8 d, respectively; however, the range in days for both the mean and median day of maximum concentrations was very large. Overall, our data set indicates a weak relationship between blood concentrations of NEFA and BHBA during the periparturient period of dairy cows, suggesting that elevated concentrations of one should not be extrapolated to suggest elevated concentrations of the other metabolite. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The change in prevalence of Campylobacter on chicken carcasses during processing: a systematic review.

PubMed

Guerin, M T; Sir, C; Sargeant, J M; Waddell, L; O'Connor, A M; Wills, R W; Bailey, R H; Byrd, J A

2010-05-01

A systematic review was conducted to evaluate the change in prevalence of Campylobacter on chicken carcasses during processing. A structured literature search of 8 electronic databases using the key words for "Campylobacter," "chicken," and "processing" identified 1,734 unique citations. Abstracts were screened for relevance by 2 independent reviewers. Thirty-two studies described prevalence at more than one stage during processing and were included in this review. Of the studies that described the prevalence of Campylobacter on carcasses before and after specific stages of processing, the chilling stage had the greatest number of studies (9), followed by washing (6), defeathering (4), scalding (2), and evisceration (1). Studies that sampled before and after scalding or chilling, or both, showed that the prevalence of Campylobacter generally decreased immediately after the stage (scalding: 20.0 to 40.0% decrease; chilling: 100.0% decrease to 26.6% increase). The prevalence of Campylobacter increased after defeathering (10.0 to 72.0%) and evisceration (15.0%). The prevalence after washing was inconsistent among studies (23.0% decrease to 13.3% increase). Eleven studies reported the concentration of Campylobacter, as well as, or instead of, the prevalence. Studies that sampled before and after specific stages of processing showed that the concentration of Campylobacter decreased after scalding (minimum decrease of 1.3 cfu/g, maximum decrease of 2.9 cfu/mL), evisceration (0.3 cfu/g), washing (minimum 0.3 cfu/mL, maximum 1.1 cfu/mL), and chilling (minimum 0.2 cfu/g, maximum 1.7 cfu/carcass) and increased after defeathering (minimum 0.4 cfu/g, maximum 2.9 cfu/mL). Available evidence is sparse and suggests more data are needed to understand the magnitude and mechanism by which the prevalence and concentration of Campylobacter changes during processing. This understanding should help researchers and program developers identify the most likely points in processing to implement effective control efforts. For example, if contamination will occur during defeathering and likely during evisceration, critical control points postevisceration are likely to have a greater effect on the end product going to the consumer.

How changes of climate extremes affect summer and winter crop yields and water productivity in the southeast USA

NASA Astrophysics Data System (ADS)

Tian, D.; Cammarano, D.

2017-12-01

Modeling changes of crop production at regional scale is important to make adaptation measures for sustainably food supply under global change. In this study, we explore how changing climate extremes in the 20th and 21st century affect maize (summer crop) and wheat (winter crop) yields in an agriculturally important region: the southeast United States. We analyze historical (1950-1999) and projected (2006-2055) precipitation and temperature extremes by calculating the changes of 18 climate extreme indices using the statistically downscaled CMIP5 data from 10 general circulation models (GCMs). To evaluate how these climate extremes affect maize and wheat yields, historical baseline and projected maize and wheat yields under RCP4.5 and RCP8.5 scenarios are simulated using the DSSAT-CERES maize and wheat models driven by the same downscaled GCMs data. All of the changes are examined at 110 locations over the study region. The results show that most of the precipitation extreme indices do not have notable change; mean precipitation, precipitation intensity, and maximum 1-day precipitation are generally increased; the number of rainy days is decreased. The temperature extreme indices mostly showed increased values on mean temperature, number of high temperature days, diurnal temperature range, consecutive high temperature days, maximum daily maximum temperature, and minimum daily minimum temperature; the number of low temperature days and number of consecutive low temperature days are decreased. The conditional probabilistic relationships between changes in crop yields and changes in extreme indices suggested different responses of crop yields to climate extremes during sowing to anthesis and anthesis to maturity periods. Wheat yields and crop water productivity for wheat are increased due to an increased CO2 concentration and minimum temperature; evapotranspiration, maize yields, and crop water productivity for wheat are decreased owing to the increased temperature extremes. We found the effects of precipitation changes on both yields are relatively uncertain.

Fluorescent biological aerosol particles (FBAPs) measured with the Waveband Integrated Bioaerosol Sensor WIBS-4: laboratory tests combined with a one year field study

NASA Astrophysics Data System (ADS)

Toprak, E.; Schnaiter, M.

2012-07-01

In this paper bioaerosol measurements conducted with the Waveband Integrated Bioaerosol Sensor mark 4 (WIBS-4) are presented. The measurements comprise aerosol chamber characterization experiments and a one-year ambient measurement period at a semi-rural site in South Western Germany. This study aims to investigate the sensitivity of WIBS-4 to biological and non-biological aerosols, performance of WIBS-4 for discrimination of several types of aerosols, and the detection and identification of biological particles in the ambient aerosol. Several types of biological and non-biological aerosol samples including spores, bacteria, pollen, mineral dust, ammonium sulphate, combustion soot, and fluorescent polystyrene spheres were analysed by WIBS-4 in the laboratory. The results confirm the sensitivity of the Ultra Violet Light Induced Fluorescence (UV-LIF) method to biological fluorophores and show the good discrimination capabilities of the two wavelengths excitation/two wavebands detection method applied in WIBS-4. However, a weak cross-sensitivity to non-biological fluorescent interferers remains and is discussed in this paper. All the laboratory studies have been undertaken in order to prepare WIBS-4 for ambient aerosol measurements. According to the one year ambient aerosol study, number concentration of fluorescent biological aerosol particles (FBAP) show strong seasonal and diurnal variability. The highest number concentration of FBAP was measured during the summer term and it decreases towards the winter period when colder and drier conditions are prevailing. Diurnal FBAP concentrations start to increase after sunset and reach maximum values during the late night and early morning hours. On the other hand the total aerosol number concentration was always higher during day time than during night time and a sharp decrease after sunset was observed. There was no correlation observed between the FBAP concentration and the meteorological parameters temperature, precipitation, wind direction and wind speed. However a clear correlation was identified between the FBAP number concentration and the relative humidity. Humidity controlled release mechanisms of some fungal spore species are discussed as a possible explanation.

Associations between mortality and prolonged exposure to elevated particulate matter concentrations in East Asia.

PubMed

Kim, Satbyul Estella; Bell, Michelle L; Hashizume, Masahiro; Honda, Yasushi; Kan, Haidong; Kim, Ho

2018-01-01

Previous epidemiological studies regarding mortality and particulate matter with an aerodynamic diameter of <10μm (PM 10 ) have considered only absolute concentrations of PM 10 as a risk factor. However, none have evaluated the durational effect of multi-day periods with high PM 10 concentrations. To evaluate the durational effect (i.e., number of days) of high PM 10 concentrations on mortality, we collected data regarding 3,662,749 deaths from 28 cities in Japan, South Korea, and China (1993-2009). Exposure was defined as consecutive days with daily PM 10 concentrations ≥75μg/m 3 . A Poisson model was used with duration as the variable of interest, while controlling for daily PM 10 concentrations, meteorological variables, seasonal trends, and day of the week. The increase in mortality risk for each additional consecutive day with PM 10 concentrations ≥75μg/m 3 was 0.68% in Japan (95% confidence interval [CI]: 0.35-1.01%), 0.48% in South Korea (95% CI: 0.30-0.66%), and 0.24% in China (95% CI: 0.14-0.33%). The annual average maximum number of consecutive days with high PM 10 in Japan (2.40days), South Korea (6.96days), and China (42.26days) was associated with non-accidental death increases of 1.64% (95% CI: 1.31-1.98%), 3.37% (95% CI: 3.19-3.56%), and 10.43% (95% CI: 10.33-10.54%), respectively. These findings may facilitate the planning of public health interventions to minimize the health burden of air pollution. Copyright © 2017 Elsevier Ltd. All rights reserved.

Factors affecting the 7Be surface concentration and its extremely high occurrences over the Scandinavian Peninsula during autumn and winter.

PubMed

Ajtić, J; Brattich, E; Sarvan, D; Djurdjevic, V; Hernández-Ceballos, M A

2018-05-01

Relationships between the beryllium-7 activity concentrations in surface air and meteorological parameters (temperature, atmospheric pressure, and precipitation), teleconnection indices (Arctic Oscillation, North Atlantic Oscillation, and Scandinavian pattern) and number of sunspots are investigated using two multivariate statistical techniques: hierarchical cluster and factor analysis. The beryllium-7 surface measurements over 1995-2011, at four sampling sites located in the Scandinavian Peninsula, are obtained from the Radioactivity Environmental Monitoring Database. In all sites, the statistical analyses show that the beryllium-7 concentrations are strongly linked to temperature. Although the beryllium-7 surface concentration exhibits the well-characterised spring/summer maximum, our study shows that extremely high beryllium-7 concentrations, defined as the values exceeding the 90 th percentile in the data records for each site, also occur over the October-March period. Two types of autumn/winter extremes are distinguished: type-1 when the number of extremes in a given month is less than three, and type-2 when at least three extremes occur in a month. Factor analysis performed for these autumn/winter events shows a weaker effect of temperature and a stronger impact of the transport and production signal on the beryllium-7 concentrations. Further, the majority of the type-2 extremes are associated with a very high monthly Scandinavian teleconnection index. The type-2 extremes that occurred in January, February and March are also linked to sudden stratospheric warmings of the Arctic vortex. Our results indicate that the Scandinavian teleconnection index might be a good indicator of the meteorological conditions facilitating extremely high beryllium-7 surface concentrations over Scandinavia during autumn and winter. Copyright © 2018 Elsevier Ltd. All rights reserved.

40 CFR 463.24 - New source performance standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... usage flow rate for cleaning processes at a new source times the following pollutant concentrations: Subpart B [Cleaning water] Concentration used to calculate NSPS Pollutant or pollutant property Maximum for any 1 day (mg/l) Maximum for monthly average (mg/l) BOD5 49 22 Oil and Grease 71 17 TSS 117 36 pH...

40 CFR 463.24 - New source performance standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... usage flow rate for cleaning processes at a new source times the following pollutant concentrations: Subpart B [Cleaning water] Concentration used to calculate NSPS Pollutant or pollutant property Maximum for any 1 day (mg/l) Maximum for monthly average (mg/l) BOD5 49 22 Oil and Grease 71 17 TSS 117 36 pH...

Environmental fate of Ra in cation-exchange regeneration brine waste disposed to septic tanks, New Jersey Coastal Plain, USA: migration to the water table.

PubMed

Szabo, Zoltan; Jacobsen, Eric; Kraemer, Thomas F; Parsa, Bahman

2010-01-01

Fate of radium (Ra) in liquid regeneration brine wastes from water softeners disposed to septic tanks in the New Jersey Coastal Plain was studied. Before treatment, combined Ra ((226)Ra plus (228)Ra) concentrations (maximum, 1.54 Bq L(-1)) exceeded the 0.185 Bq L(-1) Maximum Contaminant Level in 4 of 10 studied domestic-well waters (median pH, 4.90). At the water table downgradient from leachfields, combined Ra concentrations were low (commonly < or =0.019 Bq L(-1)) when pH was >5.3, indicating sequestration; when pH was < or =5.3 (acidic), concentrations were elevated (maximum, 0.985 Bq L(-1) - greater than concentrations in corresponding discharged septic-tank effluents (maximum, 0.243 Bq L(-1))), indicating Ra mobilization from leachfield sediments. Confidence in quantification of Ra mass balance was reduced by study design limitations, including synoptic sampling of effluents and ground waters, and large uncertainties associated with analytical methods. The trend of Ra mobilization in acidic environments does match observations from regional water-quality assessments.

Rheology of Dead Sea shampoo containing the antidandruff climbazole.

PubMed

Abu-Jdayil, B; Mohameed, H A

2004-12-01

In this study, the effect of the antidandruff climbazole on the rheology of hair shampoo containing Dead Sea (DS) salt was investigated. The presence of either DS salt or the climbazole led to increase in the shampoo viscosity. An optimum concentration was found where the viscosity of shampoo was maximum. In the absence of DS salt, the viscosity of hair shampoo increased with increasing the climbazole concentration to reach a maximum value at 1.0 wt%. Further addition of climbazole decreased the viscosity of shampoo. Adjusting the pH of the shampoo at 5.5 and 5.0 shifted the optimum climbazole concentration (corresponds to maximum viscosity) to 0.8 wt% and led to increase in the viscosity of shampoo. On the other hand, the addition of climbazole to the shampoo containing DS salt resulted in a decrease in shampoo viscosity. This decrease of shampoo viscosity became more pronounced with increasing the climbazole and/or DS salt concentrations. By controlling the pH of shampoo, an optimum formula of shampoo comprising both climbazole and DS salt and having maximum viscosity was obtained.

Optimizing the Dopant and Carrier Concentration of Ca5Al2Sb6 for High Thermoelectric Efficiency

PubMed Central

Yan, Yuli; Zhang, Guangbiao; Wang, Chao; Peng, Chengxiao; Zhang, Peihong; Wang, Yuanxu; Ren, Wei

2016-01-01

The effects of doping on the transport properties of Ca5Al2Sb6 are investigated using first-principles electronic structure methods and Boltzmann transport theory. The calculated results show that a maximum ZT value of 1.45 is achieved with an optimum carrier concentration at 1000 K. However, experimental studies have shown that the maximum ZT value is no more than 1 at 1000 K. By comparing the calculated Seebeck coefficient with experimental values, we find that the low dopant solubility in this material is not conductive to achieve the optimum carrier concentration, leading a smaller experimental value of the maximum ZT. Interestingly, the calculated dopant formation energies suggest that optimum carrier concentrations can be achieved when the dopants and Sb atoms have similar electronic configurations. Therefore, it might be possible to achieve a maximum ZT value of 1.45 at 1000 K with suitable dopants. These results provide a valuable theoretical guidance for the synthesis of high-performance bulk thermoelectric materials through dopants optimization. PMID:27406178

Characterization of glucose-insulin responsiveness and impact of fetal number and sex difference on insulin response in the sheep fetus

PubMed Central

Green, Alice S.; Macko, Antoni R.; Rozance, Paul J.; Yates, Dustin T.; Chen, Xiaochuan; Hay, William W.

2011-01-01

GSIS is often measured in the sheep fetus by a square-wave hyperglycemic clamp, but maximal β-cell responsiveness and effects of fetal number and sex difference have not been fully evaluated. We determined the dose-response curve for GSIS in fetal sheep (0.9 of gestation) by increasing plasma glucose from euglycemia in a stepwise fashion. The glucose-insulin response was best fit by curvilinear third-order polynomial equations for singletons (y = 0.018x3 − 0.26x2 + 1.2x − 0.64) and twins (y = −0.012x3 + 0.043x2 + 0.40x − 0.16). In singles, maximal insulin secretion was achieved at 3.4 ± 0.2 mmol/l glucose but began to plateau after 2.4 ± 0.2 mmol/l glucose (90% of maximum), whereas the maximum for twins was reached at 4.8 ± 0.4 mmol/l glucose. In twin (n = 18) and singleton (n = 49) fetuses, GSIS was determined with a square-wave hyperglycemic clamp >2.4 mmol/l glucose. Twins had a lower basal glucose concentration, and plasma insulin concentrations were 59 (P < 0.01) and 43% (P < 0.05) lower in twins than singletons during the euglycemic and hyperglycemic periods, respectively. The basal glucose/insulin ratio was approximately doubled in twins vs. singles (P < 0.001), indicating greater insulin sensitivity. In a separate cohort of fetuses, twins (n = 8) had lower body weight (P < 0.05) and β-cell mass (P < 0.01) than singleton fetuses (n = 7) as a result of smaller pancreata (P < 0.01) and a positive correlation (P < 0.05) between insulin immunopositive area and fetal weight (P < 0.05). No effects of sex difference on GSIS or β-cell mass were observed. These findings indicate that insulin secretion is less responsive to physiological glucose concentrations in twins, due in part to less β-cell mass. PMID:21343544

Predicting polycyclic aromatic hydrocarbons using a mass fraction approach in a geostatistical framework across North Carolina.

PubMed

Reyes, Jeanette M; Hubbard, Heidi F; Stiegel, Matthew A; Pleil, Joachim D; Serre, Marc L

2018-01-09

Currently in the United States there are no regulatory standards for ambient concentrations of polycyclic aromatic hydrocarbons (PAHs), a class of organic compounds with known carcinogenic species. As such, monitoring data are not routinely collected resulting in limited exposure mapping and epidemiologic studies. This work develops the log-mass fraction (LMF) Bayesian maximum entropy (BME) geostatistical prediction method used to predict the concentration of nine particle-bound PAHs across the US state of North Carolina. The LMF method develops a relationship between a relatively small number of collocated PAH and fine Particulate Matter (PM2.5) samples collected in 2005 and applies that relationship to a larger number of locations where PM2.5 is routinely monitored to more broadly estimate PAH concentrations across the state. Cross validation and mapping results indicate that by incorporating both PAH and PM2.5 data, the LMF BME method reduces mean squared error by 28.4% and produces more realistic spatial gradients compared to the traditional kriging approach based solely on observed PAH data. The LMF BME method efficiently creates PAH predictions in a PAH data sparse and PM2.5 data rich setting, opening the door for more expansive epidemiologic exposure assessments of ambient PAH.

Spacecraft Maximum Allowable Concentrations for Selected Airborne Contaminants. Volume 2

NASA Technical Reports Server (NTRS)

1996-01-01

The National Aeronautics and Space Administration (NASA) is aware of the potential toxicological hazards to humans that might be associated with prolonged spacecraft missions. Despite major engineering advances in controlling the atmosphere within spacecraft, some contamination of the air appears inevitable. NASA has measured numerous airborne contaminants during space missions. As the missions increase in duration and complexity, ensuring the health and well-being of astronauts traveling and working in this unique environment becomes increasingly difficult. As part of its efforts to promote safe conditions aboard spacecraft, NASA requested the National Research Council (NRC) to develop guidelines for establishing spacecraft maximum allowable concentrations (SMACs) for contaminants, and to review SMACs for various space-craft contaminants to determine whether NASA's recommended exposure limits are consistent with the guidelines recommended by the subcommittee. In response to NASA's request, the NRC organized the Subcommittee on Guidelines for Developing Spacecraft Maximum Allowable Concentrations for Space Station Contaminants within the Committee On Toxicology (COT). In the first phase of its work, the subcommittee developed the criteria and methods for preparing SMACs for spacecraft contaminants. The subcommittee's report, entitled Guidelines for Developing Spacecraft Maximum Allowable Concentrations for Space Station Contaminants, was published in 1992. The executive summary of that report is reprinted as Appendix A of this volume. In the second phase of the study, the Subcommittee on Spacecraft Maximum Allowable Concentrations reviewed reports prepared by NASA scientists and contractors recommending SMACs for approximately 35 spacecraft contaminants. The subcommittee sought to determine whether the SMAC reports were consistent with the 1992 guidelines. Appendix B of this volume contains the SMAC reports for 12 chemical contaminants that have been reviewed for their application of the guidelines developed in the first phase of this activity and approved by the subcommittee. This report is the second volume in the series Spacecraft Maximum Allowable Concentrations for Space Station Contaminants. The first volume was published in 1994.

Formation and transport of deethylatrazine and deisopropylatrazine in surface water

USGS Publications Warehouse

Thurman, E.M.; Meyer, M.T.; Mills, M.S.; Zimmerman, L.R.; Perry, C.A.; Goolsby, D.A.

1994-01-01

Field disappearance studies and a regional study of nine rivers in the Midwest Corn Belt show that deethylatrazine (DEA; 2-amino-4-chloro-6-isopropylamino-s-triazine) and deisopropylatrazine (DIA; 2-amino-4-chloro-6-ethylaminos-triazine) occur frequently in surface water that has received runoff from two parent triazine herbicides, atrazine (2-chloro-4-ethylamino-6-isopropylamino-s-triazine) and cyanazine (2-chloro-4-ethylamino-6-methylpropionitrileamino-s-triazine). The concentration of DEA and DIA in surface water varies with the hydrologic conditions of the basin and the timing of runoff, with maximum concentrations reaching 5 ??g/L (DEA + DIA). Early rainfall followed by a dry summer will result in an early peak concentration of metabolites in surface water. A wet summer will delay the maximum concentrations of metabolites and increase their runoff into surface water, occasionally resulting in a slight separation of the parent atrazine maximum concentrations from the metabolite maximum concentrations, giving a "second flush?? of triazine metabolites to surface water. Replicated field dissipation studies of atrazine and cyanazine indicate that DIA/DEA ratios will vary from 0.4 ?? 0.1 when atrazine is the major triazine present to 0.6 ?? 0.1 when significant amounts of cyanazine are present. A comparison of transport time of DEA and DIA from field plots to their appearance in surface water indicates that storage and dilution are occurring in the alluvial aquifers of the basin.

Effect of CO2 Concentration on Growth and Biochemical Composition of Newly Isolated Indigenous Microalga Scenedesmus bajacalifornicus BBKLP-07.

PubMed

Patil, Lakkanagouda; Kaliwal, Basappa

2017-05-01

Photosynthetic mitigation of CO 2 through microalgae is gaining great importance due to its higher photosynthetic ability compared to plants, and the biomass can be commercially exploited for various applications. CO 2 fixation capability of the newly isolated freshwater microalgae Scenedesmus bajacalifornicus BBKLP-07 was investigated using a 1-l photobioreactor. The cultivation was carried at varying concentration of CO 2 ranging from 5 to 25%, and the temperature and light intensities were kept constant. A maximum CO 2 fixation rate was observed at 15% CO 2 concentration. Characteristic growth parameters such as biomass productivity, specific growth rate, and maximum biomass yield, and biochemical parameters such as carbohydrate, protein, lipid, chlorophyll, and carotenoid were determined and discussed. It was observed that the effect of CO 2 concentration on growth and biochemical composition was quite significant. The maximum biomass productivity was 0.061 ± 0.0007 g/l/day, and the rate of CO 2 fixation was 0.12 ± 0.002 g/l/day at 15% CO 2 concentration. The carbohydrate and lipid content were maximum at 25% CO 2 with 26.19 and 25.81% dry cell weight whereas protein, chlorophyll, and carotenoid contents were 32.89% dry cell weight, 25.07 μg/ml and 6.15 μg/ml respectively at 15% CO 2 concentration.

Concentration levels of new-generation fungicides in throughfall released by foliar wash-off from vineyards.

PubMed

Pérez-Rodríguez, P; Soto-Gómez, D; Paradelo, M; López-Periago, J E

2017-12-01

The presence of agricultural pesticides in the environment and their effects on ecosystems are major concerns addressed in a significant number of articles. However, limited information is available on the pesticide concentrations released from crops. This study reports losses of new-generation fungicides by foliar wash-off from vineyards and their potential impact on the concentrations of their main active substances (AS) in surface waters. Two experimental plots devoted to vineyards were treated with various combinations of commercial new-generation fungicide formulations. Then, up to sixteen throughfall collectors were installed under the canopy. Concentrations of sixteen different AS in throughfall were determined along nine rainfall episodes. Concentrations in throughfall far exceeded the maximum permissible levels for drinking water established by the European Union regulations. Dynamics of fungicide release indicated a first-flush effect in the wash-off founding the highest concentrations of AS in the first rain episodes after application of the fungicides. This article shows that foliar spray application of commercial formulations of new-generation fungicides does not prevent the release of their AS to soil or the runoff. Concentration data obtained in this research can be valuable in supporting the assessment of environmental effects of new-generation fungicides and modeling their environmental fate. Copyright © 2017 Elsevier Ltd. All rights reserved.

Further investigations on the concentration of marine bacteriophages in the water around Helgoland, with reference to the phage-host systems encountered

NASA Astrophysics Data System (ADS)

Moebus, K.

1992-09-01

Between April 3 and September 24, 1991, the concentrations of bacteriophages infecting bacterial strains, isolated in 1990 and during this investigations, were determined in 35 samples of seawater taken at station ‘Kabeltonne’ adjacent to Helgoland. Similar to the findings of 1990, phage concentrations of several hundred plaque forming units (PFU) ml-1 were observed with a number of indicator strains, the maximum concentration being at least 1.5×103 PFU ml-1. These high concentrations lasted for only a few days, generally decreasing at rates between 0.6 and 0.9 day-1. Phage concentrations of 0 to 2 PFU ml-1 were found to be predominant until the end of June, occasionally attaining 5 PFU ml-1. From July through September, when high phage concentrations were observed with some indicator strains, between 0 and 10 PFU ml-1 were found in the majority of tests. As revealed by a final phage-host cross-reaction test, the greater part of 138 indicator bacteria is genetically related, and almost half of the 200 phage strains tested are propagated only by their original indicator bacterium. The possible importance of mutational events for the maintenance of phage-host systems in nature is discussed.

Identification of Watershed-scale Critical Source Areas Using Bayesian Maximum Entropy Spatiotemporal Analysis

NASA Astrophysics Data System (ADS)

Roostaee, M.; Deng, Z.

2017-12-01

The states' environmental agencies are required by The Clean Water Act to assess all waterbodies and evaluate potential sources of impairments. Spatial and temporal distributions of water quality parameters are critical in identifying Critical Source Areas (CSAs). However, due to limitations in monetary resources and a large number of waterbodies, available monitoring stations are typically sparse with intermittent periods of data collection. Hence, scarcity of water quality data is a major obstacle in addressing sources of pollution through management strategies. In this study spatiotemporal Bayesian Maximum Entropy method (BME) is employed to model the inherent temporal and spatial variability of measured water quality indicators such as Dissolved Oxygen (DO) concentration for Turkey Creek Watershed. Turkey Creek is located in northern Louisiana and has been listed in 303(d) list for DO impairment since 2014 in Louisiana Water Quality Inventory Reports due to agricultural practices. BME method is proved to provide more accurate estimates than the methods of purely spatial analysis by incorporating space/time distribution and uncertainty in available measured soft and hard data. This model would be used to estimate DO concentration at unmonitored locations and times and subsequently identifying CSAs. The USDA's crop-specific land cover data layers of the watershed were then used to determine those practices/changes that led to low DO concentration in identified CSAs. Primary results revealed that cultivation of corn and soybean as well as urban runoff are main contributing sources in low dissolved oxygen in Turkey Creek Watershed.

Magnetic nanoparticles stimulation to enhance liquid-liquid two-phase mass transfer under static and rotating magnetic fields

NASA Astrophysics Data System (ADS)

Azimi, Neda; Rahimi, Masoud

2017-01-01

Rotating magnetic field (RMF) was applied on a micromixer to break the laminar flow and induce chaotic flow to enhance mass transfer between two-immiscible organic and aqueous phases. The results of RMF were compared to those of static magnetic field (SMF). For this purpose, experiments were carried out in a T-micromixer at equal volumetric flow rates of organic and aqueous phases. Fe3O4 nanoparticles were synthesized by co-precipitation technique and they were dissolved in organic phase. Results obtained from RMF and SMF were compared in terms of overall volumetric mass transfer coefficient (KLa) and extraction efficiency (E) at various Reynolds numbers. Generally, RMF showed higher effect in mass transfer characteristics enhancement compared with SMF. The influence of rotational speeds of magnets (ω) in RMF was investigated, and measurable enhancements of KLa and E were observed. In RMF, the effect of magnetic field induction (B) was investigated. The results reveal that at constant concentration of nanoparticles, by increasing of B, mass transfer characteristics will be enhanced. The effect of various nanoparticles concentrations (ϕ) within 0.002-0.01 (w/v) on KLa and E at maximum induction of RMF (B=76 mT) was evaluated. Maximum values of KLa (2.1±0.001) and E (0.884±0.001) were achieved for the layout of RMF (B=76 mT), ω=16 rad/s and MNPs concentration of 0.008-0.01 (w/v).

An empirical investigation on thermal characteristics and pressure drop of Ag-oil nanofluid in concentric annular tube

NASA Astrophysics Data System (ADS)

Abbasian Arani, A. A.; Aberoumand, H.; Aberoumand, S.; Jafari Moghaddam, A.; Dastanian, M.

2016-08-01

In this work an experimental study on Silver-oil nanofluid was carried out in order to present the laminar convective heat transfer coefficient and friction factor in a concentric annulus with constant heat flux boundary condition. Silver-oil nanofluid prepared by Electrical Explosion of Wire technique with no nanoparticles agglomeration during nanofluid preparation process and experiments. The average sizes of particles were 20 nm. Nanofluids with various particle Volume fractions of 0.011, 0.044 and 0.171 vol% were employed. The nanofluid flowing between the tubes is heated by an electrical heating coil wrapped around it. The effects of different parameters such as flow Reynolds number, tube diameter ratio and nanofluid particle concentration on heat transfer coefficient are studied. Results show that, heat transfer coefficient increased by using nanofluid instead of pure oil. Maximum enhancement of heat transfer coefficient occurs in 0.171 vol%. In addition the results showed that, there are slight increases in pressure drop of nanofluid by increasing the nanoparticle concentration of nanofluid in compared to pure oil.

Effect of arsenic contaminated drinking water on human chromosome: a case study.

PubMed

Singh, Asha Lata; Singh, Vipin Kumar; Srivastava, Anushree

2013-10-01

Arsenic contamination of ground water has become a serious problem all over the world. Large number of people from Uttar Pradesh, Bihar and West Bengal of India are suffering due to consumption of arsenic contaminated drinking water. Study was carried out on 30 individuals residing in Ballia District, UP where the maximum concentration of arsenic was observed around 0.37 ppm in drinking water. Blood samples were collected from them to find out the problem related with arsenic. Cytogenetic study of the blood samples indicates that out of 30, two persons developed Klinefelter syndrome.

Trends in impact factors of ophthalmology journals.

PubMed

Vainer, Igor; Mimouni, Francis; Blumenthal, Eytan Z; Mimouni, Michael

2016-09-01

To test whether there is an association between the growth in the number of ophthalmic journals in the past years and their mean and maximum impact factor (IF) as a common sign of scientific proliferation. Using data from the 2013 Journal Citation Report database a study of the major clinical medical fields was conducted to assess the correlation between the number of journals and maximum IF in a given field in the year 2013. In the field of ophthalmology, we examined the correlation between year, number of journals, mean IF and maximum IF in the field of ophthalmology throughout the years 2000-2013. In the major medical fields, a positive correlation was found between the number of journals and the maximum IF (quadratic R2 = 0.71, P< 0.001). When studying the field of ophthalmology a positive correlation between the number of journals and mean IF (R2 = 0.84, P< 0.001) and between number of journals and maximum IF (R2 = 0.71, P< 0.001) was detected. Our findings suggest that the variation in the IF can be explained by the number of journals in the field of ophthalmology. In the future, the formation of additional ophthalmology journals is likely to further increase the IFs of existing journals.

Trends in impact factors of ophthalmology journals

PubMed Central

Vainer, Igor; Mimouni, Francis; Blumenthal, Eytan Z; Mimouni, Michael

2016-01-01

Purpose: To test whether there is an association between the growth in the number of ophthalmic journals in the past years and their mean and maximum impact factor (IF) as a common sign of scientific proliferation. Methods: Using data from the 2013 Journal Citation Report database a study of the major clinical medical fields was conducted to assess the correlation between the number of journals and maximum IF in a given field in the year 2013. In the field of ophthalmology, we examined the correlation between year, number of journals, mean IF and maximum IF in the field of ophthalmology throughout the years 2000–2013. Results: In the major medical fields, a positive correlation was found between the number of journals and the maximum IF (quadratic R2 = 0.71, P < 0.001). When studying the field of ophthalmology a positive correlation between the number of journals and mean IF (R2 = 0.84, P < 0.001) and between number of journals and maximum IF (R2 = 0.71, P < 0.001) was detected. Conclusions: Our findings suggest that the variation in the IF can be explained by the number of journals in the field of ophthalmology. In the future, the formation of additional ophthalmology journals is likely to further increase the IFs of existing journals. PMID:27853016

Limnological study of Lake Shastina, Siskiyou County, California

USGS Publications Warehouse

Dong, Alex E.; Beatty, Kenneth W.; Averett, Robert C.

1974-01-01

Lake Shastina provides water for irrigation in Shasta Valley, as well as recreation. Presently, its shoreline is being developed for summer homes. Surface water constituted more than 90 percent of the approximately 50,000 acre-foot (62-cubic hectometre) inflow to Lake Shastina in the 1972 water year. Controlled outflow is via the Montague Main Canal; however, leakage from the lake through volcanic rocks to the northwest was estimated to be greater than the measured outflow. Appreciable annual changes in the quantity of water in storage in the lake are related mainly to variations in annual inflow.From June through August the lake was thermally stratified. In the spring and summer the epilimnion was often supersaturated with oxygen, while at the same time the hypolimnion was undersaturated and 'often devoid of dissolved oxygen. Vertical stratification of carbon dioxide, carbonate, bicarbonate, hydrogen ion, nitrogen, and phosphorus was also recorded during the spring and summer. Orthophosphate, total phosphorus, and total nitrogen concentrations (organic, ammonium, and nitrate) were highest in the hypolimnion during the period of thermal stratification.Ten-inch (25-centimetre) core samples from the reservoir bottom were chemically analyzed at 0.8-inch (2-centimetre) intervals. The concentrations ranged from 6.3 to 28.9 milligrams per gram of iron, 0.07 to 0.43 milligrams per gram of manganese, 0.4 to 2.7 milligrams per gram of organic nitrogen plus ammonium, and 0.06 to 1.3 milligrams per gram of total phosphorus. Organic matter in the cores ranged from 4 to 14 percent.Green algae and diatoms were the dominant algal types, reaching maximum concentrations of about 7 and 30 million cells per litre, respectively. These phytoplankton occurred near the surface during thermally stratified periods, but were distributed at greater depths during nonthermally stratified periods. Blue-green algae were present only in the spring samples, and reached a maximum concentration of about 5 million cells per litre.Zooplankton numbers were greatest in March, July, and September, with lesser concentrations in June. Three major zooplankton groups, Cladocera, Copepoda, and Rotifera, were present. The major groups of benthic organisms were Oligochaeta, Chironomidae, and Chaoborus, with numbers ranging from 3350, 890, and 8450 per square metre, respectively.A discussion on algal control is included.

Effect of lactose concentration on batch production of ethanol from cheese whey using Candida pseudotropicalis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghaly, A.E.; El-Taweel, A.A.

1995-07-01

The effect of lactose concentration on growth of Candida pseudotropicalis and ethanol production from cheese whey under batch conditions was investigated. Four initial lactose concentrations ranging from 50 to 200 g/L (5 to 20% wt/vol) were used. High concentration of lactose had an inhibitory effect on the specific growth rate, lactose utilization rate, and ethanol production rate. The maximum cell concentration was influenced by the initial substrate concentration as well as ethanol concentration. Inhibition of ethanol production was more pronounced at higher initial lactose concentrations. The maximum ethanol yield (96.6% of the theoretical yield) was achieved with the 100 g/Lmore » initial substrate concentration. The results indicated that pH control during alcohol fermentation of cheese whey is not necessary. 41 refs., 12 figs., 1 tab.« less

Comparative evaluation of some commercially available brands of pharmaceutical preparations for Na, K and Mg concentrations.

PubMed

Hayat, Sikander; Chughtai, Muhammad Ismail; Ansari, Tariq Mahmood; Kamal, Ghulam Mustafa

2012-04-01

A study was carried out to investigate the concentrations of macro-elements (Na(+), K(+) and Mg(+2)) in twelve commercially available pharmaceutical preparations used as sex stimulant, by Atomic Absorption Spectrophotometer. A wet digestion method was adopted to prepare the samples. The results indicated that sodium concentration was maximum (3702 ± 29 μg g(-1)) in LB and minimum (495 ± 06 μg g(-1)) in H-E-H. Potassium concentration was maximum (6337 ± 13 μg g(-1)) in NBA while minimum (150 ± 06 μg g(-1)) in ZGRA. Magnesium concentration was maximum in V-100 (9226 ± 11 μg g(-1)) and minimum in FGRA (1194 ± 25 μg g(-1)). The concentration of macro-elements in the imported herbal preparations was in the order of Mg

Case study. Health hazards of automotive repair mechanics: thermal and lighting comfort, particulate matter and noise.

PubMed

Loupa, G

2013-01-01

An indoor environmental quality survey was conducted in a small private automotive repair shop during May 2009 (hot season) and February 2010 (cold season). It was established that the detached building, which is naturally ventilated and lit, had all the advantages of the temperate local climate. It provided a satisfactory microclimatic working environment, concerning the thermal and the lighting comfort, without excessive energy consumption for air-conditioning or lighting. Indoor number concentrations of particulate matter (PM) were monitored during both seasons. Their size distributions were strongly affected by the indoor activities and the air exchange rate of the building. During working hours, the average indoor/outdoor (I/O) number concentration ratio was 31 for PM0.3-1 in the hot season and 69 for the cold season. However I/O PM1-10 number concentration ratios were similar, 33 and 32 respectively, between the two seasons. The estimated indoor mass concentration of PM10 for the two seasons was on average 0.68 mg m(-3) and 1.19 mg m(-3), i.e., 22 and 36 times higher than outdoors, during the hot and the cold seasons, respectively. This is indicative that indoor air pollution may adversely affect mechanics' health. Noise levels were highly variable and the average LEX, 8 h of 69.3 dB(A) was below the European Union exposure limit value 87db (A). Noise originated from the use of manual hammers, the revving up of engines, and the closing of car doors or hoods. Octave band analysis indicated that the prevailing noise frequencies were in the area of the maximum ear sensitivity.

STUDIES ON THE AMOUNT OF LIGHT EMITTED BY MIXTURES OF CYPRIDINA LUCIFERIN AND LUCIFERASE

PubMed Central

Stevens, Kenneth P.

1927-01-01

1. A photometric method was devised for measuring the intensities of light emitted per cc. of hiciferin solution and calculating the amount of light emitted per gm. of dried Cypridina powder. A total of 128 runs was made and the data are incorporated in this report. 2. The maximum amount of light emitted from 1 gm. of powder under the experimental conditions was 0.655 lumens. Different samples of powder vary greatly in amount of light production. 3. When the concentration of substrate is doubled, nearly twice as much light is emitted, or an average ratio 2C/C of 1.86. Calculations of total light emissions per gm. of powder at different concentrations indicate that slightly more light is produced from the smaller concentrations. The maximum amount of light was produced by the solutions made with neutral sea water and averaged 0.445 lumens. The least light was obtained from solutions in distilled water saturated with hydrogen. The technique allows too rapid spontaneous oxidation prior to the saturation with hydrogen. The maximum amount of light from such experiments was only 0.077 lumens. Acid sea water solutions subsequently neutralized gave an average maximum of 0.386 lumens per gm. of powder per second. 4. When the concentration of enzyme is doubled, approximately the same amount of light is produced by both concentrations, although the stronger concentrations are slightly less effective than weaker ones. This undoubtedly is due to the colloidal nature of the enzyme and is a function of surface rather than of mass. In dilute solutions greater dispersion probably allows for greater adsorption to the surface of the enzyme. The average maximum amount of light produced in the series of enzyme experiments is of the magnitude 0.56 lumens per gm. of powder. PMID:19872366

Temporal dynamics of airborne fungi in Havana (Cuba) during dry and rainy seasons: influence of meteorological parameters

NASA Astrophysics Data System (ADS)

Almaguer, Michel; Aira, María-Jesús; Rodríguez-Rajo, F. Javier; Rojas, Teresa I.

2014-09-01

The aim of this paper was to determine for first time the influence of the main meteorological parameters on the atmospheric fungal spore concentration in Havana (Cuba). This city is characterized by a subtropical climate with two different marked annual rainfall seasons during the year: a "dry season" and a "rainy season". A nonviable volumetric methodology (Lanzoni VPPS-2000 sampler) was used to sample airborne spores. The total number of spores counted during the 2 years of study was 293,594, belonging to 30 different genera and five spore types. Relative humidity was the meteorological parameter most influencing the atmospheric concentration of the spores, mainly during the rainy season of the year. Winds coming from the SW direction also increased the spore concentration in the air. In terms of spore intradiurnal variation we found three different patterns: morning maximum values for Cladosporium, night peaks for Coprinus and Leptosphaeria, and uniform behavior throughout the whole day for Aspergillus/ Penicillium."

Improved efficiency in blue phosphorescent organic light-emitting diodes by the stepwise doping structure

NASA Astrophysics Data System (ADS)

Yang, Liping; Wang, Xiaoping; Kou, Zhiqi; Ji, Changyan

2017-04-01

The electro-optical properties of the blue phosphorescent organic light-emitting diodes (PHOLEDs) can be affected by the stepwise doping structure in the emitting layer (EML). A series of multi-EML devices with different doping concentration of blue dopant (FIrpic) are fabricated. The effect of the stepwise doping structure close to the electron transport layer is more obvious than that close to the hole transport layer. When the doping concentration increases gradually from the hole injection side to the electron injection side, the maximum values of the luminance, current and power efficiency can reach to 9745 cd/m2 (at 9 V), 32.0 cd/A and 25.1 lm/W in the device with the asymmetric tri-EML structure, which is improved by about 10% compared with that in the bi-EML device. When the number of the EML is four, the performance of the device becomes worse because of the interface effect resulting from different concentration of dopant.

Thermal analysis of a multi-layer microchannel heat sink for cooling concentrator photovoltaic (CPV) cells

NASA Astrophysics Data System (ADS)

Siyabi, Idris Al; Shanks, Katie; Mallick, Tapas; Sundaram, Senthilarasu

2017-09-01

Concentrator Photovoltaic (CPV) technology is increasingly being considered as an alternative option for solar electricity generation. However, increasing the light concentration ratio could decrease the system output power due to the increase in the temperature of the cells. The performance of a multi-layer microchannel heat sink configuration was evaluated using numerical analysis. In this analysis, three dimensional incompressible laminar steady flow model was solved numerically. An electrical and thermal solar cell model was coupled for solar cell temperature and efficiency calculations. Thermal resistance, solar cell temperature and pumping power were used for the system efficiency evaluation. An increase in the number of microchannel layers exhibited the best overall performance in terms of the thermal resistance, solar cell temperature uniformity and pressure drop. The channel height and width has no effect on the solar cell maximum temperature. However, increasing channel height leads to a reduction in the pressure drop and hence less fluid pumping power.

Mixed Wastewater Coupled with CO2 for Microalgae Culturing and Nutrient Removal

PubMed Central

Yao, Lili; Shi, Jianye; Miao, Xiaoling

2015-01-01

Biomass, nutrient removal capacity, lipid productivity and morphological changes of Chlorella sorokiniana and Desmodesmus communis were investigated in mixed wastewaters with different CO2 concentrations. Under optimal condition, which was 1:3 ratio of swine wastewater to second treated municipal wastewater with 5% CO2, the maximum biomass concentrations were 1.22 g L-1 and 0.84 g L-1 for C. sorokiniana and D. communis, respectively. Almost all of the ammonia and phosphorus were removed, the removal rates of total nitrogen were 88.05% for C. sorokiniana and 83.18% for D. communis. Lipid content reached 17.04% for C. sorokiniana and 20.37% for D. communis after 10 days culture. CO2 aeration increased intracellular particle numbers of both microalgae and made D. communis tend to be solitary. The research suggested the aeration of CO2 improve the tolerance of microalgae to high concentration of NH4-N, and nutrient excess stress could induce lipid accumulation of microalgae. PMID:26418261

Parameterization of bulk condensation in numerical cloud models

NASA Technical Reports Server (NTRS)

Kogan, Yefim L.; Martin, William J.

1994-01-01

The accuracy of the moist saturation adjustment scheme has been evaluated using a three-dimensional explicit microphysical cloud model. It was found that the error in saturation adjustment depends strongly on the Cloud Condensation Nucleii (CCN) concentration in the ambient atmosphere. The scheme provides rather accurate results in the case where a sufficiently large number of CCN (on the order of several hundred per cubic centimeter) is available. However, under conditions typical of marine stratocumulus cloud layers with low CCN concentration, the error in the amounts of condensed water vapor and released latent heat may be as large as 40%-50%. A revision of the saturation adjustment scheme is devised that employs the CCN concentration, dynamical supersaturation, and cloud water content as additional variables in the calculation of the condensation rate. The revised condensation model reduced the error in maximum updraft and cloud water content in the climatically significant case of marine stratocumulus cloud layers by an order of magnitude.

Analysis on shock wave speed of water hammer of lifting pipes for deep-sea mining

NASA Astrophysics Data System (ADS)

Zhou, Zhi-jin; Yang, Ning; Wang, Zhao

2013-04-01

Water hammer occurs whenever the fluid velocity in vertical lifting pipe systems for deep-sea mining suddenly changes. In this work, the shock wave was proven to play an important role in changing pressures and periods, and mathematical and numerical modeling technology was presented for simulated transient pressure in the abnormal pump operation. As volume concentrations were taken into account of shock wave speed, the experiment results about the pressure-time history, discharge-time history and period for the lifting pipe system showed that: as its concentrations rose up, the maximum transient pressure went down, so did its discharges; when its volume concentrations increased gradually, the period numbers of pressure decay were getting less and less, and the corresponding shock wave speed decreased. These results have highly coincided with simulation results. The conclusions are important to design lifting transporting system to prevent water hammer in order to avoid potentially devastating consequences, such as damage to components and equipment and risks to personnel.

Biotransference and biomagnification of selenium copper, cadmium, zinc, arsenic and lead in a temperate seagrass ecosystem from Lake Macquarie Estuary, NSW, Australia.

PubMed

Barwick, M; Maher, W

2003-10-01

In this study the biotransference of selenium copper, cadmium, zinc, arsenic and lead was measured in a contaminated seagrass ecosystem in Lake Macquarie, NSW, Australia, to determine if biomagnification of these trace metals is occurring and if they reach concentrations that pose a threat to the resident organisms or human consumers. Selenium was found to biomagnify, exceeding maximum permitted concentrations for human consumption within carnivorous fish tissue, the highest trophic level examined. Selenium concentrations measured within carnivorous fish were also above those shown to elicit sub-lethal effects in freshwater fish. As comparisons are made to selenium concentrations known to effect freshwater fish, inferences must be made with caution. There was no evidence of copper, cadmium, zinc or lead biomagnification within the food web examined. Copper, cadmium, zinc and lead concentrations were below concentrations shown to elicit adverse responses in biota. Copper concentrations within crustaceans M. bennettae and P. palagicus were found to exceed maximum permitted concentrations for human consumption. It is likely that copper concentrations within these species were accumulated due to the essential nature of this trace metal for many species of molluscs and crustaceans. Arsenic showed some evidence of biomagnification. Total arsenic concentrations are similar to those found in other uncontaminated marine ecosystems, thus arsenic concentrations are unlikely to cause adverse effects to aquatic organisms. Inorganic arsenic concentrations are below maximum permitted concentrations for human consumption.

40 CFR 463.32 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... for the finishing water processes at a point source times the following pollutant concentrations: Subpart C [Finishing water] Concentration used to calculate BPT effluent limitations Pollutant or pollutant property Maximum for any 1 day (mg/l) Maximum for monthly average (mg/l) TSS 130 37 pH (1) (1) 1...

40 CFR 463.32 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... finishing water processes at a point source times the following pollutant concentrations: Subpart C [Finishing water] Concentration used to calculate BPT effluent limitations Pollutant or pollutant property Maximum for any 1 day (mg/l) Maximum for monthly average (mg/l) TSS 130 37 pH (1) (1) 1 Within the range...

40 CFR 463.32 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... for the finishing water processes at a point source times the following pollutant concentrations: Subpart C [Finishing water] Concentration used to calculate BPT effluent limitations Pollutant or pollutant property Maximum for any 1 day (mg/l) Maximum for monthly average (mg/l) TSS 130 37 pH (1) (1) 1...

40 CFR 463.32 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... for the finishing water processes at a point source times the following pollutant concentrations: Subpart C [Finishing water] Concentration used to calculate BPT effluent limitations Pollutant or pollutant property Maximum for any 1 day (mg/l) Maximum for monthly average (mg/l) TSS 130 37 pH (1) (1) 1...

Spacecraft Maximum Allowable Concentrations (SMACs) for C3 to C8 Aliphatic Saturated Aldehydes

NASA Technical Reports Server (NTRS)

Langford, Shannon D.

2007-01-01

Spacecraft maximum allowable concentrations (SMACs) for C3 to C8, straight-chain, aliphatic aldehydes have been previously assessed and have been documented in volume 4 of Spacecraft Maximum Allowable Concentrations for Selected Airborne Contaminants (James, 2000). These aldehydes as well as associated physical properties are shown in Table 1. The C3 to C8 aliphatic aldehydes can enter the habitable compartments and contaminate breathing air of spacecraft by several routes including incomplete oxidation of alcohols in the Environmental Control and Life Support System (ECLSS) air revitalization subsystem, as a byproduct of human metabolism, through materials off-gassing, or during food preparation. These aldehydes have been detected in the atmosphere of manned space vehicles in the past. Analysis performed by NASA of crew cabin air samples from the Russian Mir Space Station revealed the presence of C3 to C8 aldehydes at concentrations peaking at approximately 0.1 mg/cu m.

Dimensionless Analysis Applied to Bacterial Chemotaxis towards NAPL Contaminants

NASA Astrophysics Data System (ADS)

Wang, X.; GAO, B.; Zhong, W.; Kihaule, K. S.; Ford, R.

2017-12-01

The use of chemotactic bacteria in bioremediation may improve the efficiency and decrease the cost of restoration, which means it has the potential to address environmental problems caused by oil spills. However, most previous studies were focused at the laboratory-scale and there lacks a formalism that can use these laboratory-scale results as input to evaluate the relative importance of chemotaxis at the field scale. In this study, a dimensionless equation is formulated to solve this problem. First, the main influential factors were extracted based on previous researches in environmental bioremediation and then five sets of dimensionless numbers were obtained according to Buckingham theory. After collecting basic parameter values and supplementary calculations to determine the concentration gradient of the chemoattractant, all dimensionless numbers were calculated and categorized into two types, those that were sensitive to chemotaxis or those to groundwater velocity. The bacteria ratio (BR), defined as the ratio of maximum bacteria concentration to its original value, was correlated with a combination of dimensionless numbers to yield, BR=cP1-0.085P20.329P30.1P4-0.098. For a bacterial ratio greater than one, the bioremediation strategy based on chemotaxis is expected to be effective, and chemotactic bacteria are expected to accumulate around NAPL contaminant sources efficiently.

Study of copper (Cu) contents in blood cockles (Anadara sp.) at Surabaya coastal waters

NASA Astrophysics Data System (ADS)

Alfionita, S.; Pursetyo, K. T.; Sahidu, A. M.

2018-04-01

Heavy metal pollution categorized as harmful effect on the environment. This study aims to determine the content and the rate of accumulation of heavy metals copper (Cu) in the mussel of cockles (Anadara sp.) This study uses observation method with descriptive analysis. The test results Cu in sea water was <0.0223 mg/L. The results have exceeded the water quality standard according to state environmental ministerial decree number 51 2004 on marine water quality standards for marine biota maximum limit of Cu in sea water is 0.008 mg/L. Copper concentration in the sediment of 6.16 mg/kg at the Wonokromo station and at the Dadapan station is 4.03 mg/kg. According to the US-EPA in 2004 on the instructions of sediment pollution classification 49.98 mg Cu/kg. The results of shells fur Cu on Wonokromo was 1.833 mg/kg and Dadapan was 1.352 mg/kg. According to the MOH Decree No.0375/B/SK/1989 about Quality Standard Biota Consumption of Metals to the maximum limit of the existing Cu concentrations in marine biota was 20 ppm or 20 mg / kg so that the content of Cu in shellfish feathers still below the limit of existing quality standards.

Comparison of concentric and eccentric bench press repetitions to failure.

PubMed

Kelly, Stephen B; Brown, Lee E; Hooker, Steven P; Swan, Pamela D; Buman, Matthew P; Alvar, Brent A; Black, Laurie E

2015-04-01

Eccentric muscle actions (ECC) are characterized by muscle lengthening, despite actin-myosin crossbridge formation. Muscles acting eccentrically are capable of producing higher levels of force compared with muscles acting concentrically. The purpose of this study was to determine whether ECC bench press yields greater strength than concentric (CON) as determined by 1 repetition maximum (1RM). Additionally, a comparison was made examining differences in the number of repetitions to failure at different relative intensities of 1RM. Thirty healthy men (age = 24.63 ± 5.6 years) were tested for 1RM in CON and ECC bench press and the number of repetitions completed at 60, 70, 80, and 90% 1RM. For CON repetitions, the weight was mechanically lowered to the chest, and the participant pressed it up until the elbows were fully extended. The ECC bench press consisted of lowering a barbell from a fully extended elbow position to the chest in a continuous controlled manner for 3 seconds as determined by electronic metronome. Paired t-tests showed that ECC 1RM (115.99 ± 31.08 kg) was significantly (p ≤ 0.05) greater than CON 1RM (93.56 ± 26.56 kg), and the number of repetitions completed at 90% 1RM was significantly (p ≤ 0.05) greater in ECC (7.67 ± 3.24) as compared with CON (4.57 ± 2.21). There were no significant differences in number of completed repetitions during CON and ECC bench press at 60, 70, and 80% 1RM. These data indicate that ECC actions yield increased force capabilities (∼120%) as compared with CON in the bench press and may be less prone to fatigue, especially at higher intensities. These differences suggest a need to develop unique strategies for training eccentrically.

Evaluation of the Alphasense Optical Particle Counter (OPC-N2) and the Grimm Portable Aerosol Spectrometer (PAS-1.108)

PubMed Central

Sousan, Sinan; Koehler, Kirsten; Hallett, Laura; Peters, Thomas M.

2017-01-01

We compared the performance of a low-cost (∼$500), compact optical particle counter (OPC, OPC-N2, Alphasense) to another OPC (PAS-1.108, Grimm Technologies) and reference instruments. We measured the detection efficiency of the OPCs by size from 0.5 to 5 μm for monodispersed, polystyrene latex (PSL) spheres. We then compared number and mass concentrations measured with the OPCs to those measured with reference instruments for three aerosols: salt, welding fume and Arizona road dust. The OPC-N2 detection efficiency for monodispersed was similar to the PAS-1.108 for particles larger than 0.8 μm (minimum of 79% at 1 μm and maximum of 101% at 3 μm). For 0.5-μm particles, the detection efficiency of OPCN2 was underestimated at 78%, whereas PAS-1.108 overestimated concentrations by 183%. The mass concentrations from the OPCs were linear (r ≥ 0.97) with those from the reference instruments for all aerosols, although the slope and intercept were different. The mass concentrations were overestimated for dust (OPC-N2, slope = 1.6; PAS-1.108, slope = 2.7) and underestimated for welding fume (OPC-N2, slope = 0.05; PAS-1.108, slope = 0.4). The coefficient of variation (CV, precision) for OPC-N2 for all experiments was between 4.2% and 16%. These findings suggest that, given site-specific calibrations, the OPC-N2 can provide number and mass concentrations similar to the PAS-1.108 for particles larger than 1 μm. PMID:28871213

Evaluation of the Alphasense Optical Particle Counter (OPC-N2) and the Grimm Portable Aerosol Spectrometer (PAS-1.108).

PubMed

Sousan, Sinan; Koehler, Kirsten; Hallett, Laura; Peters, Thomas M

2016-01-01

We compared the performance of a low-cost (∼$500), compact optical particle counter (OPC, OPC-N2, Alphasense) to another OPC (PAS-1.108, Grimm Technologies) and reference instruments. We measured the detection efficiency of the OPCs by size from 0.5 to 5 μm for monodispersed, polystyrene latex (PSL) spheres. We then compared number and mass concentrations measured with the OPCs to those measured with reference instruments for three aerosols: salt, welding fume and Arizona road dust. The OPC-N2 detection efficiency for monodispersed was similar to the PAS-1.108 for particles larger than 0.8 μm (minimum of 79% at 1 μm and maximum of 101% at 3 μm). For 0.5-μm particles, the detection efficiency of OPCN2 was underestimated at 78%, whereas PAS-1.108 overestimated concentrations by 183%. The mass concentrations from the OPCs were linear (r ≥ 0.97) with those from the reference instruments for all aerosols, although the slope and intercept were different. The mass concentrations were overestimated for dust (OPC-N2, slope = 1.6; PAS-1.108, slope = 2.7) and underestimated for welding fume (OPC-N2, slope = 0.05; PAS-1.108, slope = 0.4). The coefficient of variation (CV, precision) for OPC-N2 for all experiments was between 4.2% and 16%. These findings suggest that, given site-specific calibrations, the OPC-N2 can provide number and mass concentrations similar to the PAS-1.108 for particles larger than 1 μm.

Feeding a diet contaminated with ochratoxin A for chickens at the maximum level recommended by the EU for poultry feeds (0.1 mg/kg). 1. Effects on growth and slaughter performance, haematological and serum traits.

PubMed

Pozzo, L; Salamano, G; Mellia, E; Gennero, M S; Doglione, L; Cavallarin, L; Tarantola, M; Forneris, G; Schiavone, A

2013-05-01

The European Commission Recommendation 2006/576/EC, suggests that the maximum level of Ochratoxin A (OTA) in poultry feeds should be set at 0.1 mg OTA/kg. Thirty-six one-day-old male Hubburd broiler chickens were divided into two groups, a Control (basal diet) and an Ochratoxin A (basal diet + 0.1 mg OTA/kg) group. The growth and slaughter performance traits were recorded. The liver, spleen, bursa of Fabricius and thymus weights were measured. The erythrocyte and leukocyte numbers were assayed in blood samples, and the heterophils to lymphocytes (H/L) ratio was determined. Alpha-1-acid glycoprotein (AGP), lysozyme, the total protein and the electrophoretic pattern were evaluated in serum samples. Liver enzymes (alanino aminotransferase, ALT and aspartate aminotransferase, AST) and kidney function parameters (uric acid and creatinine) were quantified. The results revealed that feeding a 0.1 mg OTA/kg contaminated diet to chicks caused a decrease in the absolute thymus weight (p < 0.05) and a lower total protein (p < 0.01), albumin (p < 0.01), alpha (p < 0.05), beta (p = 0.001) and gamma (p = 0.001) globulins serum concentration in the Ochratoxin A group. Moreover, the albumin-to-globulin (A/G) ratio of the OTA-treated animals resulted to be higher (p < 0.05). Feeding broiler chickens, a diet contaminated with the maximum level admitted by the European Commission Recommendation (0.1 mg OTA/kg), did not affect the animal performance, slaughter traits, organ weights, haematological parameters, liver enzyme or renal function parameters concentrations but had an overall immunosuppressant effect, with reduction in the thymus weight and of the total serum protein, albumin, alpha, beta and gamma globulins concentration. Journal of Animal Physiology and Animal Nutrition © 2013 Blackwell Verlag GmbH.

A numerical study of aerosol effects on the dynamics and microphysics of a deep convective cloud in a continental environment

NASA Astrophysics Data System (ADS)

Cui, Zhiqiang; Carslaw, Kenneth S.; Yin, Yan; Davies, Stewart

2006-03-01

The effects of aerosols on a deep convective cloud in a midlatitude continental environment are studied using an axisymmetric cloud model with a sectional treatment of aerosol and hydrometeor microphysical processes. Simulations are conducted using observations from the Cooperative Convective Precipitation Experiments (CCOPE). The isolated cloud occurred in an environment with low wind shear and with relatively dry air in the midtroposphere and upper troposphere. By varying the concentration of aerosol particles in the accumulation mode within realistic limits for a continental environment, the simulated cloud exhibited different properties. The overall impact as the aerosol concentration increased is that (1) the cloud development was inhibited; (2) the precipitation was suppressed; (3) the maximum values of liquid water content decreased, but the maximum values of droplet number concentration increased before the dissipating stage; (4) a clear tendency was found for ice crystals to be larger and less numerous in the anvil cloud; and (5) there was a significant reduction of the inflow in the lower 2 km of the atmosphere. In the relatively dry environment in the midtroposphere, the latent heat changes associated with the Wegener-Bergeron-Findeisen mechanism played an important role in the upper part of the cloud at altitudes below the homogeneous freezing level. In particular, immersion freezing and latent heat release were much more rapid in the base simulation than in the increased aerosol simulation. Less latent heat release and insufficient inflow together impeded the development of the cloud with the higher aerosol loading. Our simulations suggest that continental clouds existing below the homogeneous freezing level could show an opposite response of cloud top height and anvil crystal concentrations to changes in aerosol to what has previously been reported for clouds ascending to higher levels.

Batch Tests To Determine Activity Distribution and Kinetic Parameters for Acetate Utilization in Expanded-Bed Anaerobic Reactors

PubMed Central

Fox, Peter; Suidan, Makram T.

1990-01-01

Batch tests to measure maximum acetate utilization rates were used to determine the distribution of acetate utilizers in expanded-bed sand and expanded-bed granular activated carbon (GAC) reactors. The reactors were fed a mixture of acetate and 3-ethylphenol, and they contained the same predominant aceticlastic methanogen, Methanothrix sp. Batch tests were performed both on the entire reactor contents and with media removed from the reactors. Results indicated that activity was evenly distributed within the GAC reactors, whereas in the sand reactor a sludge blanket on top of the sand bed contained approximately 50% of the activity. The Monod half-velocity constant (Ks) for the acetate-utilizing methanogens in two expanded-bed GAC reactors was searched for by combining steady-state results with batch test data. All parameters necessary to develop a model with Monod kinetics were experimentally determined except for Ks. However, Ks was a function of the effluent 3-ethylphenol concentration, and batch test results demonstrated that maximum acetate utilization rates were not a function of the effluent 3-ethylphenol concentration. Addition of a competitive inhibition term into the Monod expression predicted the dependence of Ks on the effluent 3-ethylphenol concentration. A two-parameter search determined a Ks of 8.99 mg of acetate per liter and a Ki of 2.41 mg of 3-ethylphenol per liter. Model predictions were in agreement with experimental observations for all effluent 3-ethylphenol concentrations. Batch tests measured the activity for a specific substrate and determined the distribution of activity in the reactor. The use of steady-state data in conjunction with batch test results reduced the number of unknown kinetic parameters and thereby reduced the uncertainty in the results and the assumptions made. PMID:16348175

Batch tests to determine activity distribution and kinetic parameters for acetate utilization in expanded-bed anaerobic reactors.

PubMed

Fox, P; Suidan, M T

1990-04-01

Batch tests to measure maximum acetate utilization rates were used to determine the distribution of acetate utilizers in expanded-bed sand and expanded-bed granular activated carbon (GAC) reactors. The reactors were fed a mixture of acetate and 3-ethylphenol, and they contained the same predominant aceticlastic methanogen, Methanothrix sp. Batch tests were performed both on the entire reactor contents and with media removed from the reactors. Results indicated that activity was evenly distributed within the GAC reactors, whereas in the sand reactor a sludge blanket on top of the sand bed contained approximately 50% of the activity. The Monod half-velocity constant (K(s)) for the acetate-utilizing methanogens in two expanded-bed GAC reactors was searched for by combining steady-state results with batch test data. All parameters necessary to develop a model with Monod kinetics were experimentally determined except for K(s). However, K(s) was a function of the effluent 3-ethylphenol concentration, and batch test results demonstrated that maximum acetate utilization rates were not a function of the effluent 3-ethylphenol concentration. Addition of a competitive inhibition term into the Monod expression predicted the dependence of K(s) on the effluent 3-ethylphenol concentration. A two-parameter search determined a K(s) of 8.99 mg of acetate per liter and a K(i) of 2.41 mg of 3-ethylphenol per liter. Model predictions were in agreement with experimental observations for all effluent 3-ethylphenol concentrations. Batch tests measured the activity for a specific substrate and determined the distribution of activity in the reactor. The use of steady-state data in conjunction with batch test results reduced the number of unknown kinetic parameters and thereby reduced the uncertainty in the results and the assumptions made.

Pharmaceuticals, perfluorosurfactants, and other organic wastewater compounds in public drinking water wells in a shallow sand and gravel aquifer.

PubMed

Schaider, Laurel A; Rudel, Ruthann A; Ackerman, Janet M; Dunagan, Sarah C; Brody, Julia Green

2014-01-15

Approximately 40% of U.S. residents rely on groundwater as a source of drinking water. Groundwater, especially unconfined sand and gravel aquifers, is vulnerable to contamination from septic systems and infiltration of wastewater treatment plant effluent. In this study, we characterized concentrations of pharmaceuticals, perfluorosurfactants, and other organic wastewater compounds (OWCs) in the unconfined sand and gravel aquifer of Cape Cod, Massachusetts, USA, where septic systems are prevalent. Raw water samples from 20 public drinking water supply wells on Cape Cod were tested for 92 OWCs, as well as surrogates of wastewater impact. Fifteen of 20 wells contained at least one OWC; the two most frequently-detected chemicals were sulfamethoxazole (antibiotic) and perfluorooctane sulfonate (perfluorosurfactant). Maximum concentrations of sulfamethoxazole (113 ng/L) and the anticonvulsant phenytoin (66 ng/L) matched or exceeded maximum reported concentrations in other U.S. public drinking water sources. The sum of pharmaceutical concentrations and the number of detected chemicals were both significantly correlated with nitrate, boron, and extent of unsewered residential and commercial development within 500 m, indicating that wastewater surrogates can be useful for identifying wells most likely to contain OWCs. Septic systems appear to be the primary source of OWCs in Cape Cod groundwater, although wastewater treatment plants and other sources were potential contributors to several wells. These results show that drinking water supplies in unconfined aquifers where septic systems are prevalent may be among the most vulnerable to OWCs. The presence of mixtures of OWCs in drinking water raises human health concerns; a full evaluation of potential risks is limited by a lack of health-based guidelines and toxicity assessments. © 2013. Published by Elsevier B.V. All rights reserved.

Ground-water quality in Quaternary deposits of the central High Plains aquifer, south-central Kansas, 1999

USGS Publications Warehouse

Pope, Larry M.; Bruce, Breton W.; Hansen, Cristi V.

2001-01-01

Water samples from 20 randomly selected domestic water-supply wells completed in the Quaternary deposits of south-central Kansas were collected as part of the High Plains Regional Ground-Water Study conducted by the U.S. Geological Survey's National Water-Quality Assessment Program. The samples were analyzed for about 170 water-quality constituents that included physical properties, dissolved solids and major ions, nutrients and dissolved organic carbon, trace elements, pesticides, volatile organic compounds, and radon. The purpose of this study was to provide a broad overview of ground-water quality in a major geologic subunit of the High Plains aquifer. Water from five wells (25 percent) exceeded the 500-milligrams-per-liter of dissolved solids Secondary Maximum Contaminant Level for drinking water. The Secondary Maximum Contaminant Levels of 250 milligrams per liter for chloride and sulfate were exceeded in water from one well each. The source of these dissolved solids was probably natural processes. Concentrations of most nutrients in water from the sampled wells were small, with the exception of nitrate. Water from 15 percent of the sampled wells had concentrations of nitrate greater than the 10-milligram-per-liter Maximum Contaminant Level for drinking water. Water from 80 percent of the sampled wells showed nitrate enrichment (concentrations greater than 2.0 milligrams per liter), which is more than what might be expected for natural background concentrations. This enrichment may be the result of synthetic fertilizer applications, the addition of soil amendment (manure) on cropland, or livestock production. Most trace elements in water from the sampled wells were detected only in small concentrations, and few exceeded respective water-quality standards. Only arsenic was detected in one well sample at a concentration (240 micrograms per liter) that exceeded its proposed Maximum Contaminant Level (5.0 micrograms per liter). Additionally, one concentration of iron and two concentrations of manganese were larger than the Secondary Maximum Contaminant Levels of 300 and 50 micrograms per liter, respectively. Some occurrences of trace elements may have originated from human-related sources; however, the generally small concentrations that were measured probably reflect mostly natural sources for these constituents. A total of 47 pesticide compounds from several classes of herbicides and insecticides that included triazine, organophosphorus, organochlorine, and carbamate compounds and three pesticide degradation products were analyzed in ground-water samples during this study. Water from 50 percent of the wells sampled had detectable concentrations of one or more of these 47 compounds. The herbicide atrazine and its degradation product deethylatrazine were detected most frequently (in water from eight and nine wells, respectively); other pesticides detected were the insecticides carbofuran (in water from one well) and diazinon (in water from one well), and the herbicide metolachlor (in water from two wells). However, all concentrations of these compounds were small and substantially less than established Maximum Contaminant Levels. The use of pesticides in crop production probably is largely responsible for the occurrence of pesticides in the ground-water samples collected during this study. Although concentrations of detected pesticides were small (relative to established Maximum Contaminant Levels), the synergistic effect of these concentrations and long-term exposure to multiple pesticides on human health are unknown. Water samples from the Quaternary deposits were analyzed for 85 volatile organic compounds. Water from two wells (10 percent) had a detectable concentration of a volatile organic compound. Chloroform was detected at concen-trations of 0.18 and 0.25 microgram per liter, substantially less than the 100-microgram-per-liter Maximum Contaminant Level for total trihalomethanes. In general, the occurrence and detectio

Quality of shallow ground water in areas of recent residential and commercial development, Wichita, Kansas, 2000

USGS Publications Warehouse

Pope, Larry M.; Bruce, Breton W.; Rasmussen, Patrick P.; Milligan, Chad R.

2002-01-01

Water samples from 30 randomly distributed monitoring wells in areas of recent residential and commercial development (1960-96), Wichita, Kansas, were collected in 2000 as part of the High Plains Regional Ground-Water Study conducted by the U.S. Geological Survey's National Water-Quality Assessment (NAWQA) Program. The samples were analyzed for about 170 water-quality constituents that included chlorofluorocarbons, physical properties, dissolved solids and major ions, nutrients and dissolved organic carbon, trace elements, pesticide compounds, and volatile organic compounds. The purpose of this report is to provide an assessment of water quality in recharge to shallow ground water underlying areas of recent residential and commercial development and to determine the relation of ground-water quality to overlying urban land use. Analyses of water from the 30 monitoring wells for chlorofluorocarbons were used to estimate apparent dates of recharge. Water from 18 wells with nondegraded and uncontaminated chlorofluorocarbon concentrations had calculated apparent recharge dates that ranged from 1979 to 1990 with an average date of 1986. Water from 14 monitoring wells (47 percent) exceeded the 500-milligrams-per-liter Secondary Maximum Contaminant Level established by the U.S. Environmental Protection Agency for dissolved solids in drinking water. The Secondary Maximum Contaminant Levels of 250 milligrams per liter for chloride and sulfate were exceeded in water from one well. The source of the largest concentrations of dissolved solids and associated ions, such as chloride and sulfate, in shallow ground water in the study area probably is highly mineralized water moving out of the Arkansas River into the adjacent, unconsolidated deposits and mixing with the dominant calcium bicarbonate water in the deposits. Concentrations of most nutrients in water from the sampled wells were small, with the exception of nitrate. Although water from the sampled wells did not have nitrate concentrations larger than the 10-milligram-per-liter Maximum Contaminant Level for drinking water, water from 50 percent of the sampled wells showed nitrate enrichment (concentrations greater than 2.0 milligrams per liter). Most trace elements in water from the sampled wells were detected only in small concentrations, and few exceeded respective water-quality standards. Twenty percent of iron concentrations, 40 percent of manganese concentrations, 3 percent of arsenic concentrations, and 13 percent of uranium concentrations exceeded respective Maximum Contaminant Levels or Secondary Maximum Contaminant Levels. A total of 47 pesticide compounds were analyzed in ground-water samples during this study. Water from 73 percent of the wells sampled had detectable concentrations of one or more of 8 of these 47 compounds. The herbicide atrazine or its degradation product deethylatrazine were detected most frequently (in water from 70 percent of the sampled wells). Metolachlor was detected in water from 10 percent of the wells, and simazine was detected in water from 30 percent of the wells sampled. Other pesticides detected included dieldrin, pendimethalin, prometon, and tebuthiuron (each in water from 3 percent of the wells). All concentrations of these compounds were less than established Maximum Contaminant Levels. A total of 85 volatile organic compounds (VOCs) were analyzed in ground-water samples during this study. Water from 43 percent of the wells had a detectable concentration of one or more VOCs. Chloroform was the most frequently detected VOC (23 percent of the wells sampled).Seven other VOCs were detected in water at frequencies of 13 percent or less in the wells sampled. Concentrations of VOCs were less than respective Maximum Contaminant Levels, except one sample with a concentration of 9.0 micrograms per liter for tetrachloroethylene (Maximum Contaminant Level of 5.0 micrograms per liter). An analysis of hydraulic gradient, flow velocity

Effect of dry-cleaned clothes on tetrachloroethylene levels in indoor air, personal air, and breath for residents of several New Jersey homes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, K.W.; Pellizzari, E.D.; Perritt, R.L.

1991-10-01

Several volatile organic compounds, including tetrachloroethylene, have been found to be nearly ubiquitous in residential indoor environments during previous TEAM studies. Eleven homes in New Jersey were monitored over three or five days to examine the effect of bringing freshly dry-cleaned clothes into the home on indoor air levels and personal exposures to tetrachloroethylene. Indoor air, personal air, and breath concentrations were measured over multiple 12-hrs periods before and after dry-cleaned clothes were introduced into nine of the homes. No dry-cleaned clothes were introduced into the two remaining homes. Outdoor air tetrachloroethylene concentrations were measured at six of the elevenmore » homes. Indoor/outdoor concentration ratios and source strengths were calculated at the six homes with outdoor measurements. Elevated indoor air levels and human exposures to tetrachloroethylene were measured at seven of the nine homes with dry-cleaned clothes. Indoor air concentrations reached 300 micrograms/m3 in one home and elevated indoor levels persisted for at least 48 hrs in all seven homes. Indoor/outdoor tetrachloroethylene concentration ratios exceeded 100 for the four homes with both dry-cleaned clothes and outdoor measurements. Maximum source strengths ranged from 16 to 69 mg/hr in these homes and did not directly correspond to the number of dry-cleaned garments brought into the home. Breath levels of tetrachloroethylene increased two to six-fold for participants living in seven homes with increased indoor air levels. Indoor air, personal air, and breath tetrachloroethylene concentrations were significantly related (0.05 level) to the number of garments introduced divided by the home volume.« less

Standing wave design and optimization of a simulated moving bed chromatography for separation of xylobiose and xylose under the constraints on product concentration and pressure drop.

PubMed

Lee, Chung-Gi; Choi, Jae-Hwan; Park, Chanhun; Wang, Nien-Hwa Linda; Mun, Sungyong

2017-12-08

The feasibility of a simulated moving bed (SMB) technology for the continuous separation of high-purity xylobiose (X2) from the output of a β-xylosidase X1→X2 reaction has recently been confirmed. To ensure high economical efficiency of the X2 production method based on the use of xylose (X1) as a starting material, it is essential to accomplish the comprehensive optimization of the X2-separation SMB process in such a way that its X2 productivity can be maximized while maintaining the X2 product concentration from the SMB as high as possible in consideration of a subsequent lyophilization step. To address this issue, a suitable SMB optimization tool for the aforementioned task was prepared based on standing wave design theory. The prepared tool was then used to optimize the SMB operation parameters, column configuration, total column number, adsorbent particle size, and X2 yield while meeting the constraints on X2 purity, X2 product concentration, and pressure drop. The results showed that the use of a larger particle size caused the productivity to be limited by the constraint on X2 product concentration, and a maximum productivity was attained by choosing the particle size such that the effect of the X2-concentration limiting factor could be balanced with that of pressure-drop limiting factor. If the target level of X2 product concentration was elevated, higher productivity could be achieved by decreasing particle size, raising the level of X2 yield, and increasing the column number in the zones containing the front and rear of X2 solute band. Copyright © 2017 Elsevier B.V. All rights reserved.

Metal contamination of home garden soils and cultivated vegetables in the province of Brescia, Italy: implications for human exposure.

PubMed

Ferri, Roberta; Hashim, Dana; Smith, Donald R; Guazzetti, Stefano; Donna, Filippo; Ferretti, Enrica; Curatolo, Michele; Moneta, Caterina; Beone, Gian Maria; Lucchini, Roberto G

2015-06-15

For the past century, ferroalloy industries in Brescia province, Italy produced particulate emissions enriched in manganese (Mn), lead (Pb), zinc (Zn), copper (Cu), cadmium (Cd), chromium (Cr), iron (Fe), and aluminum (Al). This study assessed metal concentrations in soil and vegetables of regions with varying ferroalloy industrial activity levels. Home gardens (n=63) were selected in three regions of varying ferroalloy plant activity durations in Brescia province. Total soil metal concentration and extractability were measured by X-Ray Fluorescence (XRF), aqua regia extraction, and modified Community Bureau of Reference (BCR) sequential extraction. Unwashed and washed spinach and turnips cultivated in the same gardens were analyzed for metal concentrations by flame atomic absorption spectrometry. Median soil Al, Cd, Fe, Mn, Pb, and Zn concentrations were significantly higher in home gardens near ferroalloy plants compared to reference home gardens. The BCR method yielded the most mobile soil fraction (the sum of extractable metals in Fractions 1 and 2) and all metal concentrations were higher in ferroalloy plant areas. Unwashed spinach showed higher metal concentrations compared to washed spinach. However, some metals in washed spinach were higher in the reference area likely due to history of agricultural product use. Over 60% of spinach samples exceeded the 2- to 4-fold Commission of European Communities and Codex Alimentarius Commission maximum Pb concentrations, and 10% of the same spinach samples exceeded 2- to 3-fold maximum Cd concentrations set by both organizations. Turnip metal concentrations were below maximum standard reference values. Prolonged industrial emissions increase median metal concentrations and most soluble fractions (BCR F1+F2) in home garden soils near ferroalloy plants. Areas near ferroalloy plant sites had spinach Cd and Pb metal concentrations several-fold above maximum standard references. We recommend thorough washing of vegetables to minimize metal exposure. Copyright © 2015 Elsevier B.V. All rights reserved.

Perchlorate in Turfgrass Systems, Suffolk County, Long Island, NY

NASA Astrophysics Data System (ADS)

Munster, J. E.; Hanson, G. N.; Jackson, W. A.

2007-12-01

Perchlorate concentrations in precipitation, grass clippings, and soil water were analyzed at nine turfgrass sites in Suffolk County, NY. The samples were collected monthly between June, 2006 and January, 2007. The soil water was collected from suction lysimeters at 100 cm depth. Four of these sites were treated with chemical fertilizer, three with organic fertilizer and two were not fertilized. Concentrations of ClO4 in grass clippings and soil water, at the sites treated with chemical fertilizer or not treated with fertilizer, are found to increase when spikes of ClO4 concentrations in precipitation are observed. We believe that the spikes in perchlorate in precipitation collected shortly after the Fourth of July are due to firework displays. The concentration of ClO4 in soil water are 1 to 3 times higher than the maximum perchlorate concentrations in precipitation, with maximum soil water concentrations ranging from 0.5 to 3.0 ppb. At the sites treated with organic fertilizer, grass clippings and soil water ClO4 concentrations increase after the fertilizer application in May. The organic fertilizer that was applied has nine mg ClO4 per kg (9,000 ppb). Soil water concentrations at the sites treated with organic fertilizer increase 100 to 300 times the maximum ClO4 concentration observed in precipitation, with maximum soil water concentrations ranging from 120 to 625 ppb. The increase in ClO4 concentrations in the soil water cannot be explained by evaporation alone since the Cl to ClO4 ratios decrease in the soil water relative to precipitation. This decrease in the Cl to ClO4 ratio suggests another source of perchlorate besides precipitation. We postulate that this additional source is associated with the decomposition of mulched grass left after mowing. Grass takes only a few weeks to decompose after mulching, thus providing a continuous source of perchlorate throughout the mowing season. The Cl to ClO4 ratio of the grass is unknown.

Metal contamination of home gardens soils and cultivated vegetables in the province of Brescia, Italy: Implications for human exposure

PubMed Central

Ferri, Roberta; Hashim, Dana; Smith, Donald R.; Guazzetti, Stefano; Donna, Filippo; Ferretti, Enrica; Curatolo, Michele; Moneta, Caterina; Beone, Gian Maria; Lucchini, Roberto G.

2015-01-01

Background For the past century, ferroalloy industries in Brescia province, Italy produced particulate emissions enriched in manganese (Mn), lead (Pb), zinc (Zn), copper (Cu), cadmium (Cd), chromium (Cr), iron (Fe), aluminum (Al). This study assessed metal concentrations in soil and vegetables of regions with varying ferroalloy industrial activity levels. Methods Home gardens (n=63) were selected in three regions of varying ferroalloy plant activity duration in Brescia province. Total soil metal concentration and extractability were measured by X-ray fluorescence (XRF), aqua regia extraction, and modified Community Bureau of Reference (BCR) sequential extraction. Unwashed and washed spinach and turnips cultivated in the same gardens were analyzed for metal concentrations by flame atomic absorption spectrometry. Results Median soil Al, Cd, Fe, Mn, Pb, and Zn concentrations were significantly higher in home gardens near ferroalloy plants compared to reference home gardens. The BCR method yielded the most mobile soil fraction (the sum of extractable metals in Fractions 1 and 2) and all metal concentrations were higher in ferroalloy plant areas. Unwashed spinach showed higher metal concentrations compared to washed spinach. However, some metals in washed spinach were higher in the reference area likely due to history of agricultural product use. Over 60% of spinach samples exceeded the 2- to 4-fold Commission of European Communities and Codex Alimentarius Commission maximum Pb concentrations, and 10% of the same spinach samples exceeded 2- to 3-fold maximum Cd concentrations set by both organizations. Turnip metal concentrations were below maximum standard reference values. Conclusions Prolonged industrial emissions increase median metal concentrations and most soluble fractions (BCR F1+F2) in home garden soils near ferroalloy plants. Areas near ferroalloy plant sites had spinach Cd and Pb metal concentrations several-fold above maximum standard references. We recommend thoroughly washing vegetables to minimize metal exposure. PMID:25777956

Anthropogenic Organic Compounds in Source and Finished Groundwater of Community Water Systems in the Piedmont Physiographic Province, Potomac River Basin, Maryland and Virginia, 2003-04

USGS Publications Warehouse

Banks, William S.L.; Reyes, Betzaida

2009-01-01

A source- and finished-water-quality assessment of groundwater was conducted in the Piedmont Physiographic Province of Maryland and Virginia in the Potomac River Basin during 2003-04 as part of the U.S. Geological Survey's National Water-Quality Assessment Program. This assessment used a two-phased approach to sampling that allowed investigators to evaluate the occurrence of more than 280 anthropogenic organic compounds (volatile organic compounds, pesticides and pesticide degradates, and other anthropogenic organic compounds). Analysis of waters from 15 of the largest community water systems in the study area were included in the assessment. Source-water samples (raw-water samples collected prior to treatment) were collected at the well head. Finished-water samples (raw water that had been treated and disinfected) were collected after treatment and prior to distribution. Phase one samples, collected in August and September 2003, focused on source water. Phase two analyzed both source and finished water, and samples were collected in August and October of 2004. The results from phase one showed that samples collected from the source water for 15 community water systems contained 92 anthropogenic organic compounds (41 volatile organic compounds, 37 pesticides and pesticide degradates, and 14 other anthropogenic organic compounds). The 5 most frequently occurring anthropogenic organic compounds were detected in 11 of the 15 source-water samples. Deethylatrazine, a degradate of atrazine, was present in all 15 samples and metolachlor ethanesulfonic acid, a degradate of metolachlor, and chloroform were present in 13 samples. Atrazine and metolachlor were present in 12 and 11 samples, respectively. All samples contained a mixture of compounds with an average of about 14 compounds per sample. Phase two sampling focused on 10 of the 15 community water systems that were selected for resampling on the basis of occurrence of anthropogenic organic compounds detected most frequently during the first phase. A total of 48 different anthropogenic organic compounds were detected in samples collected from source and finished water. There were a similar number of compounds detected in finished water (41) and in source water (39). The most commonly detected group of anthropogenic organic compounds in finished water was trihalomethanes - compounds associated with the disinfection of drinking water. This group of compounds accounted for 30 percent of the detections in source water and 44 percent of the detections in finished water, and were generally found in higher concentrations in finished water. Excluding trihalomethanes, the number of total detections was about the same in source-water samples (33) as it was in finished-water samples (35). During both phases of the study, two measurements for human-health assessment were used. The first, the Maximum Contaminant Level for drinking water, is set by the U.S. Environmental Protection Agency and represents a legally enforceable maximum concentration of a contaminant permitted in drinking water. The second, the Health-Based Screening Level, was developed by the U.S. Geological Survey, is not legally enforceable, and represents a limit for more chronic exposures. Maximum concentrations for each detected compound were compared with either the Maximum Contaminant Level or the Health-Based Screening Level when available. More than half of the compounds detected had either a Maximum Contaminant Level or a Health-Based Screening Level. A benchmark quotient was set at 10 percent (greater than or equal to 0.1) of the ratio of the detected concentration of a particular compound to its Maximum Contaminant Level, or Health-Based Screening Level. This was considered a threshold for further monitoring. During phase one, when only source water was sampled, seven compounds (chloroform, benzene, acrylonitrile, methylene chloride, atrazine, alachlor, and dieldrin) met or exceeded a benchmark quotient. No de

Chronic toxicity of diphenhydramine hydrochloride and erythromycin thiocyanate to Daphnia, Daphnia magna, in a continuous exposure test system

USGS Publications Warehouse

Meinertz, Jeffery R.; Schreier, Theresa M.; Bernardy, Jeffry A.; Franz, Jeanne L.

2011-01-01

Diphenhydramine hydrochloride (DH; Benadryl(TM), an over-the-counter antihistamine) and erythromycin thiocyanate (ET; a commonly used macrolide antibiotic) are pharmaceutical compounds whose chronic toxicity to Daphnia magna had not been characterized. Continuous exposure to DH concentrations about 5 times greater than the maximum reported environmental concentration of 0.023 μg/L for 21 days or to ET concentrations about 40 times the maximum reported environmental concentration of 6 μg/L for 21 days did not significantly impact D. magna survival and production. In this study the no observable effect concentration for DH was 0.12 μg/L and for ET was 248 μg/L.

Reconnaissance investigation of water quality, bottom sediment, and biota associated with irrigation drainage in the Lower Rio Grande Valley and Laguna Atascosa National Wildlife Refuge, Texas, 1986-87

USGS Publications Warehouse

Wells, Frank C.; Jackson, Gerry A.; Rogers, William J.

1988-01-01

Toxaphene was detected in 11 fish samples; detectable concentrations ranged from 0.98 to 5.1 micrograms per gram, wet weight. DOT also was detected in 11 fish samples with concentrations ranging from 0.021 to 0.066 micrograms per gram, wet weight. ODD was detected in 21 fish samples; concentrations ranged from 0.015 to 0.16 micrograms per gram, wet weight. DDE was detected in all 22 fish samples, and concentrations ranged from 0.36 to 9.9 micrograms per gram, wet weight. The maximum concentrations of DOT and ODD exceeded the 1980-81 baseline concentrations. The median and maximum concentrations of toxaphene and DDE exceeded the 1980-81 baseline concentrations. The largest concentrations of toxaphene, ODD, and DDE in fish were all measured in samples collected at the Main Floodway near Progreso.

Concentration Measurements in Self-Excited, Momentum-Dominated Helium Jets

NASA Technical Reports Server (NTRS)

Yildirim, Bekir Sedat

2004-01-01

Flow structure of momentum-dominated pure helium jets discharged vertically into ambient air was investigated using high-speed rainbow schlieren deflectometry (RSD) technique. Effects of the operating parameters, i.e., Reynolds number (Re) and Richardson number (Ri), on the oscillatory behavior of the flow were examined over a range of experimental conditions. To seek the individual effect of these parameters, one of them was fixed and the other was varied with certain constraints. Measurements revealed highly periodic oscillations in the laminar region as well as high regularity in transition and turbulent regions. Maximum spectral power profiles at different axial locations indicated the oscillation amplitude increasing until the breakdown of the jet in the turbulent regime. The transition from the laminar to turbulent flow was also investigated. Fast Fourier transform analysis performed in the transition regime showed that the flow oscillates at a unique frequency, which was the same in the upstream laminar flow region. Measured deflection angle data were used in Abel inversion algorithm to construct the helium concentration fields. Instantaneous helium concentration contours revealed changes in the flow structure and evolution of vortical structures during an oscillation cycle. Temporal evolution plots of helium concentration at different axial location showed repeatable oscillations at all axial and radial locations up to the turbulent regime. A cross-correlation technique, applied to find the spatial displacements of the vortical structures, provided correlation coefficient peaks between consecutive schlieren images. Results show that the vortical structure convected and accelerated only in the axial direction.

Influence of nitromethane concentration on ignition energy and explosion parameters in gaseous nitromethane/air mixtures.

PubMed

Zhang, Qi; Li, Wei; Lin, Da-Chao; He, Ning; Duan, Yun

2011-01-30

The aim of this paper is to provide new experimental data of the minimum ignition energy (MIE) of gaseous nitromethane/air mixtures to discuss the explosion pressure and the flame temperature as a function of nitromethane concentration. Observations on the influence of nitromethane concentration on combustion pressure and temperature through the pressure and temperature measure system show that peak temperature (the peak of combustion temperature wave) is always behind peak pressure (the peak of the combustion pressure wave) in arrival time, the peak combustion pressure of nitromethane increases in the range of its volume fraction 10-40% as the concentration of nitromethane increases, and it slightly decreases in the range of 40-50%. The maximum peak pressure is equal to 0.94 MPa and the minimum peak pressure 0.58 MPa. Somewhat similar to the peak pressure, the peak combustion temperature increases with the volume fraction of nitromethane in the range of 10-40%, and slightly decreases in 40-50%. The maximum peak temperature is 1340 °C and the minimum 860 °C. The combustion temperature rise rate increases with the concentration of nitromethane in 10-30%, while decreases in 30-50% and its maximum value of combustion temperature rise rate in 10-50% is 4200 °C/s at the volume fraction of 30%. Influence of the concentration of nitromethane on the combustion pressure rise rate is relatively complicated, and the maximum value of rise rate of combustion pressure wave in 10-50% is 11 MPa/s at the concentration 20%. Copyright © 2010 Elsevier B.V. All rights reserved.

Influence of time of concentration on variation of runoff from a small urbanized watershed

Treesearch

Devendra Amatya; Agnieszka Cupak; Andrzej Walega

2015-01-01

The main objective of the paper is to estimate the influence of time of concentration (TC) on maximum flow in an urbanized watershed. The calculations of maximum flow have been carried out using the Rational method, Technical Release 55 (TR55) procedure based on NRCS (National Resources Conservation Services) guidelines, and NRCS-UH rainfall-runoff model. Similarly,...

Distribution of pesticides and PCBs in sediments of agricultural drains in the Culiacan Valley, Sinaloa, Mexico.

PubMed

García-de la Parra, Luz María; Cervantes-Mojica, L Juleny; González-Valdivia, Carolina; Martínez-Cordero, Francisco J; Aguilar-Zárate, Gabriela; Bastidas-Bastidas, Pedro; Betancourt-Lozano, Miguel

2012-10-01

Agriculture is one of the most important economic activities in Sinaloa, Mexico. The Culiacan Valley is an extensive agricultural region characterized by a variety of crops with high-yield productions. In this study, concentrations of organochlorine (OCPs) and organophosphorus (OPs) pesticides and polychlorobiphenyls (PCBs) were determined in sediments of the agricultural drainage system of Culiacan Valley. Overall, 32 compounds were detected, with concentrations widely ranging from 0.03 to 1 294 ng g(-1) dry weight. OCP concentrations (15) ranged from 0.1 to 20.19 ng g(-1) dw. OP concentrations (8) ranged from 0.03 to 1294 ng g(-1) dw, and diazinon was the compound with the highest concentration. PCB concentrations were also determined and varied from 0.05 to 3.29 ng g(-1) dw. Other compounds detected included permethrin, triadimefon, and fipronil. The central zone registered the higher concentrations and the greatest number of compounds, which could be related to the occurrence of horticultural fields in this zone. According to sediment quality guidelines, the compounds exceeding the probable effect level were γ-HCH, p,p'-DDT and p,p'-DDE, while the pesticides above the maximum permissible concentration were endosulfan, azinphos methyl, diazinon, dichlorvos, and permethrin. Although Sinaloa is an important agricultural crop producer in northwest Mexico, there are not many studies dealing with pesticide distribution in agricultural areas.

Effect of operation parameters on the slagging near swirl coal burner throat

DOE Office of Scientific and Technical Information (OSTI.GOV)

Changfu You; Yong Zhou

2006-10-15

Fluid flow, heat transfer, coal combustion, and slagging processes had been numerically simulated near a swirl burner throat. The effect of the ratio distribution of each burner air, their swirling numbers, and the coal character on the slagging process had been analyzed. The computation results indicate that the maximal sticking-particle numbers occur at the uppermost waterwall, while the sticking-particle number at neither waterwall near the swirl burner outlet is very small. The swirling number has a significant effect on the number of the sticking particle. The sticking-particle number increases rapidly with the increment of the outer secondary air and themore » primary air-swirling numbers, respectively, because it can strengthen the flow entrainment ability to carry more particles to the waterwall. The inner secondary air has a complicated influence on the slagging process. When the inner secondary air-swirling number is about middle intensive degree (about 0.9), the sticking-particle number reaches maximum. If the inner secondary air-swirling number continues increasing, then the coal particles will combust completely and reduce the particle concentration, thus decrease the sticking-particle number. The ratio of each air has a slight influence on the sticking-particle number relative to the swirling number. The coal particles with small mean diameter combust completely, which can reduce the sticking-particle number. 13 refs., 16 figs., 1 tab.« less

Short term serum pharmacokinetics of diammine silver fluoride after oral application.

PubMed

Vasquez, Elsa; Zegarra, Graciela; Chirinos, Edgar; Castillo, Jorge L; Taves, Donald R; Watson, Gene E; Dills, Russell; Mancl, Lloyd L; Milgrom, Peter

2012-12-31

There is growing interest in the use of diammine silver fluoride (DSF) as a topical agent to treat dentin hypersensitivity and dental caries as gauged by increasing published research from many parts of the world. While DSF has been available in various formulations for many years, most of its pharmacokinetic aspects within the therapeutic concentration range have never been fully characterized. This preliminary study determined the applied doses (3 teeth treated), maximum serum concentrations, and time to maximum serum concentration for fluoride and silver in 6 adults over 4 h. Fluoride was determined using the indirect diffusion method with a fluoride selective electrode, and silver was determined using inductively coupled plasma-mass spectrometry. The mean amount of DSF solution applied to the 3 teeth was 7.57 mg (6.04 μL). Over the 4 hour observation period, the mean maximum serum concentrations were 1.86 μmol/L for fluoride and 206 nmol/L for silver. These maximums were reached 3.0 h and 2.5 h for fluoride and silver, respectively. Fluoride exposure was below the U.S. Environmental Protection Agency (EPA) oral reference dose. Silver exposure exceeded the EPA oral reference dose for cumulative daily exposure over a lifetime, but for occasional use was well below concentrations associated with toxicity. This preliminary study suggests that serum concentrations of fluoride and silver after topical application of DSF should pose little toxicity risk when used in adults. NCT01664871.

Short term serum pharmacokinetics of diammine silver fluoride after oral application

PubMed Central

2012-01-01

Background There is growing interest in the use of diammine silver fluoride (DSF) as a topical agent to treat dentin hypersensitivity and dental caries as gauged by increasing published research from many parts of the world. While DSF has been available in various formulations for many years, most of its pharmacokinetic aspects within the therapeutic concentration range have never been fully characterized. Methods This preliminary study determined the applied doses (3 teeth treated), maximum serum concentrations, and time to maximum serum concentration for fluoride and silver in 6 adults over 4 h. Fluoride was determined using the indirect diffusion method with a fluoride selective electrode, and silver was determined using inductively coupled plasma-mass spectrometry. The mean amount of DSF solution applied to the 3 teeth was 7.57 mg (6.04 μL). Results Over the 4 hour observation period, the mean maximum serum concentrations were 1.86 μmol/L for fluoride and 206 nmol/L for silver. These maximums were reached 3.0 h and 2.5 h for fluoride and silver, respectively. Conclusions Fluoride exposure was below the U.S. Environmental Protection Agency (EPA) oral reference dose. Silver exposure exceeded the EPA oral reference dose for cumulative daily exposure over a lifetime, but for occasional use was well below concentrations associated with toxicity. This preliminary study suggests that serum concentrations of fluoride and silver after topical application of DSF should pose little toxicity risk when used in adults. Clinical trials registration NCT01664871. PMID:23272643

Quantifying primary and secondary source contributions to ultrafine particles in the UK urban background

NASA Astrophysics Data System (ADS)

Hama, S. M. L.; Cordell, R. L.; Monks, P. S.

2017-10-01

Total particle number (TNC, ≥7 nm diameter), particulate matter (PM2.5), equivalent black carbon (eBC) and gaseous pollutants (NO, NO2, NOx, O3, CO) have been measured at an urban background site in Leicester over two years (2014 and 2015). A derived chemical climatology for the pollutants showed maximum concentrations for all pollutants during the cold period except O3 which peaked during spring. Quantification of primary and secondary sources of ultrafine particles (UFPs) was undertaken using eBC as a tracer for the primary particle number concentration in the Leicester urban area. At the urban background site, which is influenced by fresh vehicle exhaust emissions, TNC was segregated into two components, TNC = N1 + N2. The component N1 represents components directly emitted as particles and compounds which nucleate immediately after emission. The component N2 represents the particles formed during the dilution and cooling of vehicle exhaust emissions and by in situ new particle formation (NPF). The values of highest N1 (49%) were recorded during the morning rush hours (07:00-09:00 h), correlating with NOx, while the maximum contribution of N2 to TNC was found at midday (11:00-14:00 h), at around 62%, correlated with O3. Generally, the percentage of N2 (57%) was greater than the percentage of N1 (43%) for all days at the AURN site over the period of the study. For the first time the impact of wind speed and direction on N1 and N2 was explored. The overall data analysis shows that there are two major sources contributing to TNC in Leicester: primary sources (traffic emissions) and secondary sources, with the majority of particles being of secondary origin.

Checking distributional assumptions for pharmacokinetic summary statistics based on simulations with compartmental models.

PubMed

Shen, Meiyu; Russek-Cohen, Estelle; Slud, Eric V

2016-08-12

Bioequivalence (BE) studies are an essential part of the evaluation of generic drugs. The most common in vivo BE study design is the two-period two-treatment crossover design. AUC (area under the concentration-time curve) and Cmax (maximum concentration) are obtained from the observed concentration-time profiles for each subject from each treatment under each sequence. In the BE evaluation of pharmacokinetic crossover studies, the normality of the univariate response variable, e.g. log(AUC) 1 or log(Cmax), is often assumed in the literature without much evidence. Therefore, we investigate the distributional assumption of the normality of response variables, log(AUC) and log(Cmax), by simulating concentration-time profiles from two-stage pharmacokinetic models (commonly used in pharmacokinetic research) for a wide range of pharmacokinetic parameters and measurement error structures. Our simulations show that, under reasonable distributional assumptions on the pharmacokinetic parameters, log(AUC) has heavy tails and log(Cmax) is skewed. Sensitivity analyses are conducted to investigate how the distribution of the standardized log(AUC) (or the standardized log(Cmax)) for a large number of simulated subjects deviates from normality if distributions of errors in the pharmacokinetic model for plasma concentrations deviate from normality and if the plasma concentration can be described by different compartmental models.

Comparison of charged nanoparticle concentrations near busy roads and overhead high-voltage power lines.

PubMed

Jayaratne, E R; Ling, X; Morawska, L

2015-09-01

Overhead high-voltage power lines are known sources of corona ions. These ions rapidly attach to aerosols to form charged particles in the environment. Although the effect of ions and charged particles on human health is largely unknown, much attention has focused on the increasing exposure as a result of the expanding power network in urban residential areas. However, it is not widely known that a large number of charged particles in urban environments originate from motor vehicle emissions. In this study, for the first time, we compare the concentrations of charged nanoparticles near busy roads and overhead power lines. We show that large concentrations of both positive and negative charged nanoparticles are present near busy roadways and that these concentrations commonly exceed those under high-voltage power lines. We estimate that the concentration of charged nanoparticles found near two freeways carrying around 120 vehicles per minute exceeded the corresponding maximum concentrations under two corona-emitting overhead power lines by as much as a factor of 5. The difference was most pronounced when a significant fraction of traffic consisted of heavy-duty diesel vehicles which typically have high particle and charge emission rates. Copyright © 2015 Elsevier B.V. All rights reserved.

How do changes in bulk soil organic carbon content affect carbon concentrations in individual soil particle fractions?

PubMed Central

Yang, X. M.; Drury, C. F.; Reynolds, W. D.; Yang, J. Y.

2016-01-01

We test the common assumption that organic carbon (OC) storage occurs on sand-sized soil particles only after the OC storage capacity on silt- and clay-sized particles is saturated. Soil samples from a Brookston clay loam in Southwestern Ontario were analysed for the OC concentrations in bulk soil, and on the clay (<2 μm), silt (2–53 μm) and sand (53–2000 μm) particle size fractions. The OC concentrations in bulk soil ranged from 4.7 to 70.8 g C kg−1 soil. The OC concentrations on all three particle size fractions were significantly related to the OC concentration of bulk soil. However, OC concentration increased slowly toward an apparent maximum on silt and clay, but this maximum was far greater than the maximum predicted by established C sequestration models. In addition, significant increases in OC associated with sand occurred when the bulk soil OC concentration exceeded 30 g C kg−1, but this increase occurred when the OC concentration on silt + clay was still far below the predicted storage capacity for silt and clay fractions. Since the OC concentrations in all fractions of Brookston clay loam soil continued to increase with increasing C (bulk soil OC content) input, we concluded that the concept of OC storage capacity requires further investigation. PMID:27251365

How do changes in bulk soil organic carbon content affect carbon concentrations in individual soil particle fractions?

NASA Astrophysics Data System (ADS)

Yang, X. M.; Drury, C. F.; Reynolds, W. D.; Yang, J. Y.

2016-06-01

We test the common assumption that organic carbon (OC) storage occurs on sand-sized soil particles only after the OC storage capacity on silt- and clay-sized particles is saturated. Soil samples from a Brookston clay loam in Southwestern Ontario were analysed for the OC concentrations in bulk soil, and on the clay (<2 μm), silt (2-53 μm) and sand (53-2000 μm) particle size fractions. The OC concentrations in bulk soil ranged from 4.7 to 70.8 g C kg-1 soil. The OC concentrations on all three particle size fractions were significantly related to the OC concentration of bulk soil. However, OC concentration increased slowly toward an apparent maximum on silt and clay, but this maximum was far greater than the maximum predicted by established C sequestration models. In addition, significant increases in OC associated with sand occurred when the bulk soil OC concentration exceeded 30 g C kg-1, but this increase occurred when the OC concentration on silt + clay was still far below the predicted storage capacity for silt and clay fractions. Since the OC concentrations in all fractions of Brookston clay loam soil continued to increase with increasing C (bulk soil OC content) input, we concluded that the concept of OC storage capacity requires further investigation.

Estimating potency for the Emax-model without attaining maximal effects.

PubMed

Schoemaker, R C; van Gerven, J M; Cohen, A F

1998-10-01

The most widely applied model relating drug concentrations to effects is the Emax model. In practice, concentration-effect relationships often deviate from a simple linear relationship but without reaching a clear maximum because a further increase in concentration might be associated with unacceptable or distorting side effects. The parameters for the Emax model can only be estimated with reasonable precision if the curve shows sign of reaching a maximum, otherwise both EC50 and Emax estimates may be extremely imprecise. This paper provides a solution by introducing a new parameter (S0) equal to Emax/EC50 that can be used to characterize potency adequately even if there are no signs of a clear maximum. Simulations are presented to investigate the nature of the new parameter and published examples are used as illustration.

Characteristics of water, sediment, and benthic communities of the Wolf River, Menominee Indian Reservation, Wisconsin, water years 1986-98

USGS Publications Warehouse

Garn, Herbert S.; Scudder, Barbara C.; Richards, Kevin D.; Sullivan, Daniel J.

2001-01-01

Analyses and interpretation of water quality, sediment, and biological data from water years 1986 through 1998 indicated that land use and other human activities have had only minimal effects on water quality in the Wolf River upstream from and within the Menominee Indian Reservation in northeastern Wisconsin. Relatively high concentrations of calcium and magnesium (natural hardness), iron, manganese, and aluminum were measured in Wolf River water samples during water years 1986?98 from the three sampled sites and attributed to presence of highly mineralized geologic materials in the basin. Average calcium and magnesium concentrations varied from 22?26 milligrams per liter (mg/L) and 11?13 mg/L, respectively. Average iron concentrations ranged from 290?380 micrograms per liter (?g/L); average manganese concentrations ranged from 53?56 mg/L. Average aluminum concentrations ranged from 63?67 ?g/L. Mercury was present in water samples but concentrations were not at levels of concern. Levels of Kjeldahl nitrogen, ammonia, nitrite plus nitrate, total phosphorus, and orthophosphorus in water samples were often low or below detection limits (0.01? 0.10 mg/L). Trace amounts of atrazine (maximum concentration of 0.031 ?g/L), deethylatrazine (maximum 0.032 ?g/L), and alachlor (maximum of 0.002 ?g/L) were detected. Low concentrations of most trace elements were found in streambed sediment. Tissues of fish and aquatic invertebrates collected once each year from 1995 through 1998 at the Langlade and Keshena sites, near the northern and southern boundaries of the Reservation, respectively, were low in concentrations of most trace elements. Arsenic and silver in fish livers from both sites were less than or equal to 2 ?g/g arsenic and less than 1 ?g/g silver for dry weight analysis, and concentrations of antimony, beryllium, cadmium, cobalt, lead, nickel, and uranium were all below detection limits (less than 1 ?g/g dry weight). Concentrations of most other trace elements in fish were low, with the exceptions of chromium, copper, mercury, and selenium; however, these concentrations are not at levels of concern. Concentrations of all trace elements analyzed in whole caddisfly larvae also were low compared to those reported in the literature. During 1998, a total of 48 species of macroinvertebrates were identified at each of two sampled sites, with similar numbers of genera represented at both: 41 at Keshena and 44 at Langlade. The percentage EPT (Ephemeroptera, Plecoptera, and Trichoptera) was 52 at Keshena and 77 at Langlade; these relatively large percentages suggest very good to excellent water quality at these sites. A total of 52 algal taxa were identified at the Wolf River near Langlade. Diatoms made up 96 percent of the algal biomass. A total of 58 algal taxa were identified at Keshena, including 48 diatom taxa (83 percent). Although diatoms accounted for just 22 percent of the algal relative abundance, in cells per square centimeter, diatoms contributed 91 percent of the total algal biomass. The overall biological integrity of the Keshena and Langlade sites, based on diversity, siltation, and pollution indexes for diatoms is excellent.

Micropropagation of seedless lemon (Citrus limon L. cv. Kaghzi Kalan) and assessment of genetic fidelity of micropropagated plants using RAPD markers.

PubMed

Goswami, Komal; Sharma, R; Singh, P K; Singh, Govind

2013-01-01

A micropropagation protocol was developed for multiplication of seedless lemon (Citrus limon L. cv. Kaghzi Kalan) using nodal explants. The maximum shoot regeneration was observed on low level of BAP (0.1 mg l(-1)) or kinetin (0.5 mg l(-1)). BA was recorded to be better than kinetin in terms of number of days taken to bud break. The maximum number of shoots per explant was observed on 0.1 mg l(-1) BA and 0.5 mg l(-1) kinetin. Shoot proliferation decreased with increasing concentration of BA alone, but in case of a combination of BA and NAA (0.1 mg l(-1) each), it increased with increasing concentration of BA up to 10.0 mg l(-1). None of the treatments including BA or kinetin alone or BA in combination with NAA produced significantly more shoots for commercial exploitation. In the case of a combination of BA + kinetin + IBA, the maximum (5.5 shoots per explants) proliferation was observed on MS medium containing 1.0 mg l(-1) BA + 0.5 mg l(-1) kinetin + 0.5 mg l(-1) IBA or 0.25 mg l(-1) BA + 1.0 mg l(-1) kinetin + 1.0 mg l(-1) IBA. Regenerated shoots showed root induction on MS basal medium or on MS medium containing 1.0 mg l(-1) IBA. It is concluded that a five-fold increase (1.0 mg l(-1) BA + 0.5 mg l(-1) kinetin + 0.5 mg l(-1) IBA) in axillary shoot proliferation, while seven-fold increase (0.25 mg/l mg l(-1) BA + 1.0 mg l(-1) kinetin + 1.0 mg l(-1) IBA) during the second cycle of multiplication could be obtained using the two plant growth regulator combinations. PCR amplification with 14 different random primers confirmed no somaclonal variant up to two cycles of shoot multiplication.

Preparation of nanomaterials for the ultrasound-enhanced removal of Pb2+ ions and malachite green dye: Chemometric optimization and modeling.

PubMed

Dil, Ebrahim Alipanahpour; Ghaedi, Mehrorang; Asfaram, Arash; Hajati, Shaaker; Mehrabi, Fatemeh; Goudarzi, Alireza

2017-01-01

Copper oxide nanoparticle-loaded activated carbon (CuO-NP-AC) was synthesized and characterized using different techniques such as FE-SEM, XRD and FT-IR. It was successfully applied for the ultrasound-assisted simultaneous removal of Pb 2+ ions and malachite green (MG) dye in binary system from aqueous solution. The effect of important parameters was modeled and optimized by artificial neural network (ANN) and response surface methodology (RSM). Maximum simultaneous removal percentages (>99.0%) were found at 25mgL -1 , 20mgL -1 , 0.02g, 5min and 6.0 corresponding to initial Pb 2+ concentration, initial MG concentration, CuO-NP-AC amount, ultrasonication time and pH, respectively. The precision of the equation obtained by RSM was confirmed by the analysis of variance and calculation of correlation coefficient relating the predicted and the experimental values of ultrasound-assisted simultaneous removal of the analytes. A good agreement between experimental and predicted values was observed. A feed-forward neural network with a topology optimized by response surface methodology was successfully applied for the prediction of ultrasound-assisted simultaneous removal of Pb 2+ ions and MG dye in binary system by CuO-NPs-AC. The number of hidden neurons, MSE, R 2 , number of epochs and error histogram were chosen for ANN modeling. Then, Langmuir, Freundlich, Temkin and D-R isothermal models were applied for fitting the experimental data. It was found that the Langmuir model well describes the isotherm data with a maximum adsorption capacity of 98.328 and 87.719mgg -1 for Pb 2+ and MG, respectively. Kinetic studies at optimum condition showed that maximum Pb 2+ and MG adsorption is achieved within 5min of the start of most experiments. The combination of pseudo-second-order rate equation and intraparticle diffusion model was applicable to explain the experimental data of ultrasound-assisted simultaneous removal of Pb 2+ and MG at optimum condition obtained from RSM. Copyright © 2016 Elsevier B.V. All rights reserved.

Double-tailored nonimaging reflector optics for maximum-performance solar concentration.

PubMed

Goldstein, Alex; Gordon, Jeffrey M

2010-09-01

A nonimaging strategy that tailors two mirror contours for concentration near the étendue limit is explored, prompted by solar applications where a sizable gap between the optic and absorber is required. Subtle limitations of this simultaneous multiple surface method approach are derived, rooted in the manner in which phase space boundaries can be tailored according to the edge-ray principle. The fundamental categories of double-tailored reflective optics are identified, only a minority of which can pragmatically offer maximum concentration at high collection efficiency. Illustrative examples confirm that acceptance half-angles as large as 30 mrad can be realized at a flux concentration of approximately 1000.

Analyses of ozone in urban and rural sites in Málaga (Spain).

PubMed

Dueñas, C; Fernández, M C; Cañete, S; Carretero, J; Liger, E

2004-08-01

Ozone concentrations were measured at two (urban and a rural) sites near the city of Málaga (Spain). The aim of this study was to determine the daily, monthly and seasonal variation patterns of ozone concentrations at both sites and to study the possible regional influences. The daily variations mostly have the usual features with the afternoon maximum and the night minimum being more pronounced in the urban area. The average monthly concentrations throughout the year start to increase in March reaching their maximum values in July for the urban site. However, in the rural area, the monthly variations are smaller reaching their maximum value in June. The hourly evolution of the ozone concentrations in both sampling sites is well defined in spring and summer and not so well defined in autumn and winter. Taking into account the four seasons, the rural concentrations are higher than the urban ones. Summer is the season when there are similar concentrations at both sampling sites. Average hourly summer afternoon ozone for the hours 12:00-20:00 LST exceeded the 110 microg m(-3) European Union guidelines for human health for 8 h ozone exposure at the urban and rural sites.

Dose rates of antimicrobial substances in boar semen preservation-time to establish new protocols.

PubMed

Schulze, M; Grobbel, M; Riesenbeck, A; Brüning, S; Schaefer, J; Jung, M; Grossfeld, R

2017-06-01

To achieve a standardized number of spermatozoa in the final AI dose, varying amounts of extender fluid with a fixed concentration of antimicrobial substances are currently added to boar ejaculates. This practice ignores the different degrees of dilution of the antimicrobials in the end product. In calculating the final concentration of gentamicin in AI doses from 27,538 processed boar ejaculates, we demonstrated varying gentamicin concentrations in the resultant extended boar semen samples. The median concentration was 220.37 mg/L. In 25 of the samples (0.09%), the gentamicin concentration fell below 5 mg/L, which is close to or below the epidemiological cut-off value for many bacteria. We calculated the minimum inhibitory concentration of gentamicin for bacteria isolated from raw and extended ejaculates. Five of the isolates from extended ejaculates exceeded the maximum test concentration of 512 mg/L. As a result, we are presenting an alternative method of boar semen preservation whereby a particular combination of gentamicin concentrate and antibiotic-free extender is incorporated that standardizes the antibiotic concentration in the diluted semen. The addition of standardized antibiotic concentrations did not negatively affect sperm quality when compared to the use of ready-to-use extenders. In conclusion, an end volume-based and standardized addition of gentamicin to boar ejaculates can be a helpful alternative to prevent insufficient dosage of antibiotics in liquid preserved boar semen without affecting semen quality. © 2017 Blackwell Verlag GmbH.

On Atom-Bond Connectivity Index

NASA Astrophysics Data System (ADS)

Zhou, Bo; Xing, Rundan

2011-02-01

The atom-bond connectivity (ABC) index, introduced by Estrada et al. in 1998, displays an excellent correlation with the formation heat of alkanes. We give upper bounds for this graph invariant using the number of vertices, the number of edges, the Randíc connectivity indices, and the first Zagreb index. We determine the unique tree with the maximum ABC index among trees with given numbers of vertices and pendant vertices, and the n-vertex trees with the maximum, and the second, the third, and the fourth maximum ABC indices for n ≥ 6.

Spatial and temporal characterization of traffic emissions in urban microenvironments with a mobile laboratory

NASA Astrophysics Data System (ADS)

Pirjola, L.; Lähde, T.; Niemi, J. V.; Kousa, A.; Rönkkö, T.; Karjalainen, P.; Keskinen, J.; Frey, A.; Hillamo, R.

2012-12-01

A measurement campaign by a mobile laboratory van was performed in urban microenvironments bounded by a busy street Mannerheimintie in the city center of Helsinki, Finland. The characteristics of spatiotemporally high-resolution pollutant concentrations were studied such as ultrafine particles in the size range of 3-414 nm, black carbon BC, fine particle mass PM2.5, as well as nitrogen oxides NO and NO2. In addition, the effects of street geometry and roadside structure on the local dispersion of traffic emissions were analyzed as well. Meteorological conditions stayed stable and the wind direction was perpendicular to Mannerheimintie during the campaign. The highest particle concentrations were ˜8 × 105 cm-3, of which around 94% was smaller than 40 nm. At the pavement, the average concentration was in maximum 5 × 104 cm-3; around 80% of the particles was smaller than 40 nm. The volatility fraction was 75% by number. Due to the street canyon effect by the surrounding buildings, the downwind concentrations were around 24% of the upwind concentrations for particle number, 28% of NO, 39% of BC and 70% of NO2 concentrations. Furthermore, the upwind concentrations were higher than the simultaneously measured concentrations within the traffic flow. In fact, the particle count was around 3-fold, BC 2.5-fold, PM2.5 and NO2 1.5-fold compared to the concentrations while driving. Thus, for this measurement site and under these meteorological conditions, the exposure to pedestrians and cyclist on the upwind pavement is even higher than the driver's exposure. If the downwind buildings were parallel to Mannerheimintie, the concentrations dropped significantly at the pavement and continued decreasing slightly in the courtyards. When the downwind buildings were perpendicular to Mannerheimintie, a gradual reduction in the concentrations between the buildings was observed. However, at a distance of approximately a hundred meters a parallel side street which was a street canyon, started to affect the concentrations resulting in an increased exposure risk for pedestrians and cyclists. Understanding the local transport and the dispersion of traffic emissions are important for city planning and air quality assessment.

Molecular mechanism of acetylcholine receptor-controlled ion translocation across cell membranes

PubMed Central

Cash, Derek J.; Hess, George P.

1980-01-01

Two molecular processes, the binding of acetylcholine to the membrane-bound acetylcholine receptor protein and the receptor-controlled flux rates of specific inorganic ions, are essential in determining the electrical membrane potential of nerve and muscle cells. The measurements reported establish the relationship between the two processes: the acetylcholine receptor-controlled transmembrane ion flux of 86Rb+ and the concentration of carbamoylcholine, a stable analog of acetylcholine. A 200-fold concentration range of carbamoylcholine was used. The flux was measured in the millisecond-to-minute time region by using a quench flow technique with membrane vesicles prepared from the electric organ of Electrophorus electricus in eel Ringer's solution at pH 7.0 and 1°C. The technique makes possible the study of the transmembrane transport of specific ions, with variable known internal and external ion concentrations, in a system in which a determinable number of receptors is exposed to a known concentration of ligand. The response curve of ion flux to ligand was sigmoidal with an average maximum rate of 84 sec-1. Carbamoylcholine induced inactivation of the receptor with a maximum rate of 2.7 sec-1 and a different ligand dependence so that it was fast relative to ion flux at low ligand concentration but slow relative to ion flux at high ligand concentration. The simplest model that fits the data consists of receptor in the active and inactive states in ligand-controlled equilibria. Receptor inactivation occurs with one or two ligand molecules bound. For channel opening, two ligand molecules bound to the active state are required, and cooperativity results from the channel opening process itself. With carbamoylcholine, apparently, the equilibrium position for the channel opening step is only one-fourth open. The integrated rate equation, based on the model, predicts the time dependence of receptor-controlled ion flux over the concentration range of carbamoylcholine investigated. The values of the constants in the rate equation form the basis for predicting receptor-controlled changes in the transmembrane potential of cells and the conditions leading to transmission of signals between cells. PMID:6928684

Continuum study on the oscillatory characteristics of carbon nanocones inside single-walled carbon nanotubes

NASA Astrophysics Data System (ADS)

Ansari, R.; Sadeghi, F.; Darvizeh, M.

2016-02-01

This article aims to present a comprehensive study on the oscillatory behavior of concentric carbon nanocones (CNCs) inside carbon nanotubes (CNTs) using a continuum approach. To this end, the optimum radius of nanotube for which the nanocone lies on the tube axis is determined based on the distribution of suction energy. Using the Runge-Kutta numerical integration scheme, the equation of motion is solved numerically to attain the time history of displacement and velocity of nanocone. It is observed that the oscillation of nanocone occurs with respect to its axial equilibrium distance which moves further away from the middle axis of nanotube as the number of pentagons increases. A novel semi-analytical expression as a function of geometrical parameters, initial conditions and cone vertex direction is also proposed for the precise evaluation of oscillation frequency. With respect to the proposed frequency expression, a detailed parametric study is conducted to get an insight into the effects of number of pentagons, cone vertex direction and initial conditions on the oscillatory behavior of CNC-CNT oscillators. It is found that nanocones with more pentagons generate greater maximum frequencies inside nanotubes. Furthermore, it is shown that higher maximum frequencies can be achieved if the nanocone enters the nanotube from base.

Fluoride in the drinking water of Nagaur tehsil of Nagaur District, Rajasthan, India.

PubMed

Arif, M; Hussain, I; Hussain, J; Sharma, S; Kumar, S

2012-06-01

Fluoride concentration of groundwater samples from 100 villages of Nagaur tehsil was determined, 85 villages were found to have fluoride concentration more than 1.5 mg/L. The maximum fluoride concentration was recorded 6.6 mg/L in groundwater of Singhani village, while the minimum was recorded in Kurchhi village. As per the desirable and maximum permissible limit for fluoride in drinking water, determined by World Health Organization, the groundwater of about 85 villages of the studied sites is unfit for drinking purpose.

Toxic metals in imported fruits and vegetables marketed in Kuwait

DOE Office of Scientific and Technical Information (OSTI.GOV)

Husain, A.; Baroon, Z.; Al-Khalafawi, M.

1995-12-31

The concentration of lead, cadmium, and mercury in 134 samples of imported fruits and vegetables marketed in Kuwait were determined using an atomic absorption spectrophotometer with a graphite furnace and the cold vapor technique. Results obtained showed that the concentration of these metal ions in most cases did not exceed the maximum permissible concentration of metals in fresh fruits and vegetables as restricted by some countries. Only a few samples of fruits and vegetables contained levels of mercury, cadmium, and lead which exceeded these maximum permissible levels.

Bisphenol a in canned food products from canadian markets.

PubMed

Cao, Xu-Liang; Corriveau, Jeannette; Popovic, Svetlana

2010-06-01

A method based on solid phase extraction followed by derivatization and gas chromatography-mass spectrometry analysis was validated for the determination of bisphenol A (BPA) in canned food products. This method was used to analyze 78 canned food products for BPA. Concentrations of BPA in canned food products differed considerably among food types, but all were below the specific migration limit of 0.6 mg/kg set by the European Commission Directive for BPA in food or food simulants. Canned tuna products had the highest BPA concentrations in general, with mean and maximum values of 137 and 534 ng/g, respectively. BPA concentrations in the condensed soup products were considerably higher than those in the ready-to-serve soup products, with mean and maximum values of 105 and 189 ng/g, respectively, for the condensed soups and 15 and 34 ng/g, respectively, for the ready-to-serve soups. BPA concentrations in canned vegetable products were relatively low; about 60% of the products had BPA concentrations of less than 10 ng/g. Canned tomato paste products had lower BPA concentrations than did canned pure tomato products. The mean and maximum BPA concentrations were 1.1 and 2.1 ng/g, respectively, for tomato paste products and 9.3 and 23 ng/g, respectively, for the pure tomato products.

Variance Difference between Maximum Likelihood Estimation Method and Expected A Posteriori Estimation Method Viewed from Number of Test Items

ERIC Educational Resources Information Center

Mahmud, Jumailiyah; Sutikno, Muzayanah; Naga, Dali S.

2016-01-01

The aim of this study is to determine variance difference between maximum likelihood and expected A posteriori estimation methods viewed from number of test items of aptitude test. The variance presents an accuracy generated by both maximum likelihood and Bayes estimation methods. The test consists of three subtests, each with 40 multiple-choice…

Data and performances of selected aircraft and rotorcraft

NASA Astrophysics Data System (ADS)

Filippone, Antonio

2000-11-01

The purpose of this article is to provide a synthetic and comparative view of selected aircraft and rotorcraft (nearly 300 of them) from past and present. We report geometric characteristics of wings (wing span, areas, aspect-ratios, sweep angles, dihedral/anhedral angles, thickness ratios at root and tips, taper ratios) and rotor blades (type of rotor, diameter, number of blades, solidity, rpm, tip Mach numbers); aerodynamic data (drag coefficients at zero lift, cruise and maximum absolute glide ratio); performances (wing and disk loadings, maximum absolute Mach number, cruise Mach number, service ceiling, rate of climb, centrifugal acceleration limits, maximum take-off weight, maximum payload, thrust-to-weight ratios). There are additional data on wing types, high-lift devices, noise levels at take-off and landing. The data are presented on tables for each aircraft class. A graphic analysis offers a comparative look at all types of data. Accuracy levels are provided wherever available.

Climate change impacts on faecal indicator and waterborne pathogen concentrations and disease

NASA Astrophysics Data System (ADS)

Hofstra, Nynke; Vermeulen, Lucie C.; Wondmagegn, Berhanu Y.

2013-04-01

Changes in temperature and precipitation patterns may impact on the concentrations of the faecal indicator E. coli and waterborne pathogens, such as Cryptosporidium, in the surface water, and consequently - through drinking water, recreational water or consumption of irrigated vegetables - on the risk of waterborne disease. Although an increased temperature would generally increase the decline of pathogens and therefore decrease the surface water concentrations, increased precipitation and an increased incidence of extreme precipitation may increase surface water concentrations through increased (sub-)surface runoff and an increased risk of sewer overflows. And while the diluting effect of increased precipitation decreases the surface water concentration, decreased precipitation increases the percentage of sewage in the surface water and therefore increases the concentration. Moreover, (extreme) precipitation after drought may also increase the concentration. Changes in behaviour, such as increased recreation and irrigation with higher temperatures may impact on the disease risk. What the balance is between these positive and negative impacts of climate change on faecal indicator and waterborne pathogen concentrations and disease is not well known yet. A lack of available statistical or process-based models and suitable scenarios prevents quantitative analyses. We will present two examples of recent studies that aim to assess the impact of climate change on faecal indicator concentrations and waterborne disease. The first is a study on the relationship between climate variables and E. coli concentrations in the water of river systems in the Netherlands for the period 1985 - 2010. This study shows that each of the variables water temperature (negatively), precipitation and discharge (both positively) are significantly correlated with E. coli concentrations for most measurement locations. We will also present a linear regression model, including all of these variables. In the second example we assess the relationship between the weather variables precipitation and minimum and maximum temperature and the number of diarrhoeal cases in Ethiopia. We have digitised data from the Ethiopian health service and hospitals on the number of diarrhoeal cases for the period 2005 - 2010 and used meteorological data from their weather service. Very strong correlations can be found between the monthly weather variables and the number of diarrhoeal cases and a linear regression model including all variables explains a large part of the variability of the data. The studies indicate that climate change may increase the waterborne pathogen concentration in surface water and disease risk and should therefore not be ignored as a threat to microbial water quality.

Some common indices of group diversity: upper boundaries.

PubMed

Solanas, Antonio; Selvam, Rejina M; Navarro, José; Leiva, David

2012-12-01

Workgroup diversity can be conceptualized as variety, separation, or disparity. Thus, the proper operationalization of diversity depends on how a diversity dimension has been defined. Analytically, the minimal diversity must be obtained when there are no differences on an attribute among the members of a group, however maximal diversity has a different shape for each conceptualization of diversity. Previous work on diversity indexes indicated maximum values for variety (e.g., Blau's index and Teachman's index), separation (e.g., standard deviation and mean Euclidean distance), and disparity (e.g., coefficient of variation and the Gini coefficient of concentration), although these maximum values are not valid for all group characteristics (i.e., group size and group size parity) and attribute scales (i.e., number of categories). We demonstrate analytically appropriate upper boundaries for conditional diversity determined by some specific group characteristics, avoiding the bias related to absolute diversity. This will allow applied researchers to make better interpretations regarding the relationship between group diversity and group outcomes.

Exploiting Bounded Signal Flow for Graph Orientation Based on Cause-Effect Pairs

NASA Astrophysics Data System (ADS)

Dorn, Britta; Hüffner, Falk; Krüger, Dominikus; Niedermeier, Rolf; Uhlmann, Johannes

We consider the following problem: Given an undirected network and a set of sender-receiver pairs, direct all edges such that the maximum number of "signal flows" defined by the pairs can be routed respecting edge directions. This problem has applications in communication networks and in understanding protein interaction based cell regulation mechanisms. Since this problem is NP-hard, research so far concentrated on polynomial-time approximation algorithms and tractable special cases. We take the viewpoint of parameterized algorithmics and examine several parameters related to the maximum signal flow over vertices or edges. We provide several fixed-parameter tractability results, and in one case a sharp complexity dichotomy between a linear-time solvable case and a slightly more general NP-hard case. We examine the value of these parameters for several real-world network instances. For many relevant cases, the NP-hard problem can be solved to optimality. In this way, parameterized analysis yields both deeper insight into the computational complexity and practical solving strategies.

Correlation of seasonal variations in phosphorous and nitrogen species in upper Black Warrior River with duckweed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gabrielson, F.C. Jr.; Malatino, A.M.; Santa Cruz, G.J.

1980-10-01

Water samples taken throughout the year from a drainage system that had supported giant duckweed blooms were analyzed for nitrogen and phosphorus. Although seasonal separation of the data indicates possible differences within an imppoundment (Bayview Lake), extreme variations make meaningful conclusions difficult. Daily discharge from a large number of points may have masked seasonal differences. Extensive plant mats were present at minimal levels of nitrogen and phosphorus. The growth rate seemed to be governed more by climate than nutrient conditions. Laboratory investigations indicate that giant duckweed can grow under a wide range of nutrient conditions including high heavy metal concentrations.more » Growth rate data show that without a continual input of nutrients, maximum growth rates do not usually continue beyond 14 to 20 days regardless of the initial single element concentration. With a continuous nutrient input, growth would probably only be inhibited by extreme climate conditions.« less

Enhancement of convective heat transfer coefficient of ethylene glycol base cuprous oxide (Cu2O) nanofluids

NASA Astrophysics Data System (ADS)

Hassan, Ali; Ramzan, Naveed; Umer, Asim; Ahmad, Ayyaz; Muryam, Hina

2018-02-01

The enhancement in the convective heat transfer coefficient of the ethylene glycol (EG) base cuprous oxide (Cu2O) nanofluids were investigated. The nanofluids of different volume concentrations i-e 1%, 2.5% and 4.5% were prepared by the two step method. Cuprous oxide (Cu2O) nanoparticles were ultrasonically stirred for four hours in the ethylene glycol (EG). The experimental study has been performed through circular tube geometry in laminar flow regime at average Reynolds numbers 36, 71 and 116. The constant heat flux Q = 4000 (W/m2) was maintained during this work. Substantial enhancement was observed in the convective heat transfer coefficient of ethylene glycol (EG) base cuprous oxide (Cu2O) nanofluids than the base fluid. The maximum 74% enhancement was observed in convective heat transfer coefficient at 4.5 vol% concentration and Re = 116.

Standardized Treatment of Neonatal Status Epilepticus Improves Outcome.

PubMed

Harris, Mandy L; Malloy, Katherine M; Lawson, Sheena N; Rose, Rebecca S; Buss, William F; Mietzsch, Ulrike

2016-12-01

We aimed to decrease practice variation in treatment of neonatal status epilepticus by implementing a standardized protocol. Our primary goal was to achieve 80% adherence to the algorithm within 12 months. Secondary outcome measures included serum phenobarbital concentrations, number of patients progressing from seizures to status epilepticus, and length of hospital stay. Data collection occurred for 6 months prior and 12 months following protocol implementation. Adherence of 80% within 12 months was partially achieved in patients diagnosed in our hospital; in pretreated patients, adherence was not achieved. Maximum phenobarbital concentrations were decreased (56.8 vs 41.0 µg/mL), fewer patients progressed from seizures to status epilepticus (46% vs 36%), and hospital length of stay decreased by 9.7 days in survivors. In conclusion, standardized, protocol-driven treatment of neonatal status epilepticus improves consistency and short-term outcome. © The Author(s) 2016.

Biodiesel production in crude oil contaminated environment using Chlorella vulgaris.

PubMed

Xaaldi Kalhor, Aadel; Mohammadi Nassab, Adel Dabbagh; Abedi, Ehsan; Bahrami, Ahmad; Movafeghi, Ali

2016-12-01

Biodiesel is a valuable alternative to fossil fuels and many countries choose biodiesel as an unconventional energy source. A large number of investigations have been done on microalgae as a source of oil production. In recent years, wastewater pollutions have caused many ecological problems, and therefore, wastewater phycoremediation has attracted the international attention. This paper studied the cultivation of Chlorella vulgaris in a crude oil polluted environment for biodiesel production. Intended concentrations were 10 and 20gperliter (crude oil/water) at two times. The results showed that the growth of C. vulgaris was improved in wastewater and the maximum amount of dry mass and oil was produced at the highest concentration of crude oil (0.41g and 0.15g/l, respectively). In addition, dry mass and oil yield of the microalga were significantly enhanced by increasing the experiment duration. Copyright © 2016 Elsevier Ltd. All rights reserved.

Analysis and comparison of biotreatment of air polluted with ethanol using biofiltration and biotrickling filtration.

PubMed

Morotti, Karine; Ramirez, Antonio Avalos; Jones, J Peter; Heitz, Michèle

2011-12-01

This study analyses the performance of ethanol biofiltration with percolation (biotrickling filtration, BTF) comparing to a conventional biofilter (biofiltration, BF). Two biofilters packed with clay balls were operated in a range of inlet concentrations of ethanol in the air varying from 0.47 to 2.36 g m(-3). For both the BF and BTF, the specific growth rate (mu) and the elimination capacity (EC) decreased with the ethanol inlet concentration, presenting a kinetic of substrate inhibition. A Haldane-type model was adjusted for both biofilters in order to model both EC and mu as a function of the ethanol inlet concentration in the gas. The maximum EC was similar for both biofilters, at around 46 g m(-3) h(-1), whereas the maximum mu was 0.0057 h(-1) for the BF and 0.0103 h(-1) for the BTF. The maximum of ethanol removed, occurred at the lowest inlet concentration of (0.47 gm(-3)), and reached 86% for the BF and 74% for the BTF.

Incorporation of Pr into LuAG ceramics

NASA Astrophysics Data System (ADS)

Marchewka, M. R.; Chapman, M. G.; Qian, H.; Jacobsohn, L. G.

2017-06-01

An investigation of the effects of Pr in (Lu1-xPrx)3Al5O12 (LuAG:Pr) ceramics was carried out by means of x-ray diffraction (XRD), energy dispersive x-ray spectroscopy (EDX), and attenuated total reflection Fourier transform infrared spectroscopy (ATR FTIR) measurements coupled with luminescence measurements. It was found that the Pr concentration that maximizes luminescence emission depends on the thermal processing conditions. While the calcined LuAG:Pr powder showed maximum luminescence emission for Pr concentrations between 0.18 and 0.33 at.%, maximum emission of ceramic bodies sintered at 1500 °C for 20 h was obtained with Pr concentrations between 0.018 and 0.18 at.%. Further, for short sintering times up to about 3 h, luminescence emission intensity is maximum for Pr concentrations around 0.33 at.%. Longer sintering times lead to the formation of PrAlO3 as a secondary phase, concomitant with a reduction of the intensity of luminescence emission.

[Exploratory study of air quality in elementary schools, Coimbra, Portugal].

PubMed

Ferreira, Ana Maria Conceiçã; Cardoso, Salvador Massano

2013-12-01

To analyze the air quality in elementary schools and their structural and functional conditions. Air quality in 51 elementary schools (81 classrooms) in the city of Coimbra, Portugal, both inside and outside of the rooms was evaluated during the four seasons, from 2010 to 2011. Temperature (T°), relative humidity (Hr), concentrations of carbon monoxide (CO), carbon dioxide (CO2), ozone (O3), nitrogen dioxide (NO2), sulfur dioxide (SO2), compounds were evaluated, as were volatile organics (VOC), formaldehyde and particulate matter (PM10), from November 2010 to February 2011 (autumn/winter) and March 2011 to June 2011 (spring/summer). A grid characterizing the structural and functional conditions of the schools was created. The statistical Student t test for paired samples and the Wilcoxon t test were applied. In 47 schools, the average CO2 concentrations were above the maximum reference concentration (984 ppm) mentioned in Portuguese legislation. The maximum concentration values found inside the rooms were critical, especially in the fall/winter (5,320 ppm). In some schools the average concentrations of VOC and PM10 within the maximum concentration exceeded the reference legislated. The values (risk) of CO, formaldehyde, NO2, SO2 and O3 detected were not relevant. There was a higher concentration of pollutants inside the rooms compared with outside. Inadequate ventilation is associated with high CO2 concentration in the classroom.

Yearly trend of dicarboxylic acids in organic aerosols from south of Sweden and source attribution

NASA Astrophysics Data System (ADS)

Hyder, Murtaza; Genberg, Johan; Sandahl, Margareta; Swietlicki, Erik; Jönsson, Jan Åke

2012-09-01

Seven aliphatic dicarboxylic acids (C3-C9) along with phthalic acid, pinic acid and pinonic acid were determined in 35 aerosol (PM10) samples collected over the year at Vavihill sampling station in south of Sweden. Mixture of dichloromethane and methanol (ratio 1:3) was preferred over water for extraction of samples and extraction was assisted by ultrasonic agitation. Analytes were derivatized using N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) containing 1% trimethylsilyl chloride and analyzed using gas chromatography/mass spectrometry. Among studied analytes, azelaic acid was found maximum with an average concentration of 6.0 ± 3.6 ng m-3 and minimum concentration was found for pimelic acid (1.06 ± 0.63 ng m-3). A correlation coefficients analysis was used for defining the possible sources of analytes. Higher dicarboxylic acids (C7-C9) showed a strong correlation with each other (correlation coefficients (r) range, 0.96-0.97). Pinic and pinonic acids showed an increase in concentration during summer. Lower carbon number dicarboxylic acids (C3-C6) and phthalic acid were found strongly correlated, but showed a poor correlation with higher carbon number dicarboxylic acids (C7-C9), suggesting a different source for them. Biomass burning, vehicle exhaust, photo-oxidation of volatile organic compounds (natural and anthropogenic emissions) were possible sources for dicarboxylic acids.

Monte Carlo ray-tracing simulations of luminescent solar concentrators for building integrated photovoltaics

NASA Astrophysics Data System (ADS)

Leow, Shin Woei; Corrado, Carley; Osborn, Melissa; Carter, Sue A.

2013-09-01

Luminescent solar concentrators (LSCs) have the ability to receive light from a wide range of angles, concentrating the captured light onto small photo active areas. This enables greater incorporation of LSCs into building designs as windows, skylights and wall claddings in addition to rooftop installations of current solar panels. Using relatively cheap luminescent dyes and acrylic waveguides to effect light concentration onto lesser photovoltaic (PV) cells, there is potential for this technology to approach grid price parity. We employ a panel design in which the front facing PV cells collect both direct and concentrated light ensuring a gain factor greater than one. This also allows for flexibility in determining the placement and percentage coverage of PV cells during the design process to balance reabsorption losses against the power output and level of light concentration desired. To aid in design optimization, a Monte-Carlo ray tracing program was developed to study the transport of photons and loss mechanisms in LSC panels. The program imports measured absorption/emission spectra and transmission coefficients as simulation parameters with interactions of photons in the panel determined by comparing calculated probabilities with random number generators. LSC panels with multiple dyes or layers can also be simulated. Analysis of the results reveals optimal panel dimensions and PV cell layouts for maximum power output for a given dye concentration, absorbtion/emission spectrum and quantum efficiency.

Temporal variability of chlorophyll distribution in the Gulf of Mexico: bio-optical data from profiling floats

NASA Astrophysics Data System (ADS)

Pasqueron de Fommervault, Orens; Perez-Brunius, Paula; Damien, Pierre; Camacho-Ibar, Victor F.; Sheinbaum, Julio

2017-12-01

Chlorophyll concentration is a key oceanic biogeochemical variable. In the Gulf of Mexico (GOM), its distribution, which is mainly obtained from satellite surface observations and scarce in situ experiments, is still poorly understood. In 2011-2012, eight profiling floats equipped with biogeochemical sensors were deployed for the first time in the GOM and generated an unprecedented dataset that significantly increased the number of chlorophyll vertical distribution measurements in the region. The analysis of these data, once calibrated, permits us to reconsider the spatial and temporal variability of the chlorophyll concentration in the water column. At a seasonal scale, results confirm the surface signal seen by satellites, presenting maximum concentrations in winter and low values in summer. It is shown that the deepening of the mixed layer is the primary factor triggering the chlorophyll surface increase in winter. In the GOM, a possible interpretation is that this surface increase corresponds to a biomass increase. However, the present dataset suggests that the basin-scale climatological surface increase in chlorophyll content results from a vertical redistribution of subsurface chlorophyll and/or photoacclimation processes, rather than a net increase of biomass. One plausible explanation for this is the decoupling between the mixed-layer depth and the deep nutrient reservoir since mixed-layer depth only reaches the nitracline in sporadic events in the observations. Float measurements also provide evidence that the depth and the magnitude of the deep chlorophyll maximum is strongly controlled by the mesoscale variability, with higher chlorophyll biomass generally observed in cyclones rather than anticyclones.

[Ultrasound physiotherapy treatment of prostatitis].

PubMed

Talberg, P I; Andryukhin, M I; Mazina, S E; Nikolaev, A L

2016-12-01

Develop a method of treatment of prostatitis based on the use of a standard antibiotic, immunomodulatory therapy, and transrectal ultrasound physiotherapy. The dynamics of the accumulation of the antibiotic was investigated in male rats. Sonication was performed immediately before the administration of the antibiotic and its accumulation in the process at 10, 20, 40, 60, 80, 100 min after dosing. The clinical study included 138 patients with chronic prostatitis. Patients of the experimental group, in addition to standard therapy, 10 sessions of transrectal ultrasound physical therapy was performed. The efficacy of treatment was assessed after 14 and 28 days after initiation. and its discussion. Experiments on laboratory animals have shown that the highest concentration and the residence time of antibiotic in the prostate tissue is noted ultrasonic treatment in the period of maximum blood concentration of the test drug. The data obtained allow to determine that the ultrasonic treatment must be performed considering the pharmacokinetics of the antibiotic. In conducting clinical trials on day 14 of treatment and clinical manifestations of prostatitis bacterial microflora in prostatic secretions were no patients in both groups. In 15% of patients of the experimental group the number of leukocytes decreased to the normal range. After 28 days the amount of leukocytes was normal in 51% of patients in the control and 85% in the experimental group. In animal experiments defined the optimal time interval separating the moment of injection of the antibiotic from the beginning of sonication. Clinical studies have shown that the transrectal ultrasound exposure during the period of maximum concentration of the antibiotic in the blood, improves patient outcomes by 33.8%.

Pharmacokinetic modeling of a gel-delivered dapivirine microbicide in humans.

PubMed

Halwes, Michael E; Steinbach-Rankins, Jill M; Frieboes, Hermann B

2016-10-10

Although a number of drugs have been developed for the treatment and prevention of human immunodeficiency virus (HIV) infection, it has proven difficult to optimize the drug and dosage parameters. The vaginal tissue, comprised of epithelial, stromal and blood compartments presents a complex system which challenges evaluation of drug kinetics solely through empirical effort. To provide insight into the underlying processes, mathematical modeling and computational simulation have been applied to the study of retroviral microbicide pharmacokinetics. Building upon previous pioneering work that modeled the delivery of Tenofovir (TFV) via topical delivery to the vaginal environment, here we computationally evaluate the performance of the retroviral inhibitor dapivirine released from a microbicide gel. We adapt the TFV model to simulate the multicompartmental diffusion and uptake of dapivirine into the blood plasma and vaginal compartments. The results show that dapivirine is expected to accumulate at the interface between the gel and epithelium compartments due to its hydrophobic characteristics. Hydrophobicity also results in decreased diffusivity, which may impact distribution by up to 2 orders of magnitude compared to TFV. Maximum concentrations of dapivirine in the epithelium, stroma, and blood were 9.9e7, 2.45e6, and 119pg/mL, respectively. This suggests that greater initial doses or longer time frames are required to obtain higher drug concentrations in the epithelium. These observations may have important ramifications if a specific time frame is required for efficacy, or if a minimum/maximum concentration is needed in the mucus, epithelium, or stroma based on combined efficacy and safety data. Copyright © 2016 Elsevier B.V. All rights reserved.

Saharan Dust Event Impacts on Cloud Formation and Radiation over Western Europe

NASA Technical Reports Server (NTRS)

Bangert, M.; Nenes, A.; Vogel, B.; Vogel, H.; Barahona, D.; Karydis, V. A.; Kumar, P.; Kottmeier, C.; Blahak, U.

2013-01-01

We investigated the impact of mineral dust particles on clouds, radiation and atmospheric state during a strong Saharan dust event over Europe in May 2008, applying a comprehensive online-coupled regional model framework that explicitly treats particle-microphysics and chemical composition. Sophisticated parameterizations for aerosol activation and ice nucleation, together with two-moment cloud microphysics are used to calculate the interaction of the different particles with clouds depending on their physical and chemical properties. The impact of dust on cloud droplet number concentration was found to be low, with just a slight increase in cloud droplet number concentration for both uncoated and coated dust. For temperatures lower than the level of homogeneous freezing, no significant impact of dust on the number and mass concentration of ice crystals was found, though the concentration of frozen dust particles reached up to 100 l-1 during the ice nucleation events. Mineral dust particles were found to have the largest impact on clouds in a temperature range between freezing level and the level of homogeneous freezing, where they determined the number concentration of ice crystals due to efficient heterogeneous freezing of the dust particles and modified the glaciation of mixed phase clouds. Our simulations show that during the dust events, ice crystals concentrations were increased twofold in this temperature range (compared to if dust interactions are neglected). This had a significant impact on the cloud optical properties, causing a reduction in the incoming short-wave radiation at the surface up to -75Wm-2. Including the direct interaction of dust with radiation caused an additional reduction in the incoming short-wave radiation by 40 to 80Wm-2, and the incoming long-wave radiation at the surface was increased significantly in the order of +10Wm-2. The strong radiative forcings associated with dust caused a reduction in surface temperature in the order of -0.2 to -0.5K for most parts of France, Germany, and Italy during the dust event. The maximum difference in surface temperature was found in the East of France, the Benelux, and Western Germany with up to -1 K. This magnitude of temperature change was sufficient to explain a systematic bias in numerical weather forecasts during the period of the dust event.

Relaxation and transport properties of Li+ ion conducting biocompatible material for battery application

NASA Astrophysics Data System (ADS)

Hegde, Shreedatta; Ravindrachary, V.; Praveena, S. D.; Guruswamy, B.; Sagar, Rohan N.; Sanjeev, Ganesh

2018-04-01

Solid polymer electrolyte based on lithium chloride doped Poly (vinyl) alcohol composites are prepared by solution casting method. XRD results show that the crystallinity of the polymer interrupted upon LiCl doping and amorphous nature increases with dopant concentration. Impedance analysis revealed that conductivity of PVA increases with doping level and maximum ionic conductivity is observed to be 6.69 × 10-3 S/cm for 15 wt% LiCl doped PVA composite at 353K. Wagner's polarization technique has been followed to calculate ion transport number for high conducting electrolyte and transient study confirmed the presence of single charge species within the polymer electrolyte.

Height Dependency of Aerosol-Cloud Interaction Regimes: Height Dependency of ACI Regime

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Jingyi; Liu, Yangang; Zhang, Minghua

This study investigates the height dependency of aerosol-cloud interaction regimes in terms of the joint dependence of the key cloud microphysical properties (e.g. cloud droplet number concentration, cloud droplet relative dispersion, etc.) on aerosol number concentration (N a) and vertical velocity (w). The three distinct regimes with different microphysical features are the aerosol-limited regime, the updraft-limited regime, and the transitional regime. The results reveal two new phenomena in updraft-limited regime: 1) The “condensational broadening” of cloud droplet size distribution in contrast to the well-known “condensational narrowing” in the aerosol-limited regime; 2) Above the level of maximum supersaturation, some cloud dropletsmore » are deactivated into interstitial aerosols in the updraft-limited regime whereas all droplets remain activated in the aerosol-limited regime. Further analysis shows that the particle equilibrium supersaturation plays important role in understanding these unique features. Also examined is the height of warm rain initiation and its dependence on N a and w. The rain initiation height is found to depend primarily on either N a or w or both in different N a-w regimes, thus suggesting a strong regime dependence of the second aerosol indirect effect.« less

Height Dependency of Aerosol-Cloud Interaction Regimes: Height Dependency of ACI Regime

DOE PAGES

Chen, Jingyi; Liu, Yangang; Zhang, Minghua; ...

2018-01-10

This study investigates the height dependency of aerosol-cloud interaction regimes in terms of the joint dependence of the key cloud microphysical properties (e.g. cloud droplet number concentration, cloud droplet relative dispersion, etc.) on aerosol number concentration (N a) and vertical velocity (w). The three distinct regimes with different microphysical features are the aerosol-limited regime, the updraft-limited regime, and the transitional regime. The results reveal two new phenomena in updraft-limited regime: 1) The “condensational broadening” of cloud droplet size distribution in contrast to the well-known “condensational narrowing” in the aerosol-limited regime; 2) Above the level of maximum supersaturation, some cloud dropletsmore » are deactivated into interstitial aerosols in the updraft-limited regime whereas all droplets remain activated in the aerosol-limited regime. Further analysis shows that the particle equilibrium supersaturation plays important role in understanding these unique features. Also examined is the height of warm rain initiation and its dependence on N a and w. The rain initiation height is found to depend primarily on either N a or w or both in different N a-w regimes, thus suggesting a strong regime dependence of the second aerosol indirect effect.« less

Influence of multiple light-scattering on TiO2 nanoparticles imbedded into stratum corneum on light transmittance in UV and visible wavelength regions

NASA Astrophysics Data System (ADS)

Popov, Alexey P.; Priezzhev, Alexander V.; Lademann, Jürgen; Myllylä, Risto

2007-05-01

This paper focuses on the simulation of propagation of radiation in UV and visible wavelength regions within a superficial skin layer (stratum corneum, SC) partially filled with titanium dioxide (TiO II) nanoparticles. Volume concentrations of the particles (0.67% - 2.25%) correspond to the maximal concentrations of the considered particles in the frames of independent scattering. Transmittance of 307-, 400-, and 500-nm light through a 20-μm thick SC is calculated. The effect of the TiO II nanoparticles on the contribution of photons undergone different numbers of scattering acts into transmittance is considered. It is shown that administration of the nanoparticles results in the broadening of the distribution of transmitted photons over undergone scattering acts. It also results in the shift of the maximum location of this distribution to larger number of scattering acts for the wavelengths of 400 and 500 nm being the latter the most pronounced. The increase of undergone scattering acts leads to the elongation of photon trajectories within the medium and results in the increase of the diffuse reflected light and the transmittance decrease.

Phytoremediation of crude oil-contaminated soil employing Crotalaria pallida Aiton.

PubMed

Baruah, P; Deka, S; Baruah, P P

2016-06-01

The purpose of the study was to evaluate the phytoremediation potentiality of a herb named Crotalaria pallida which are abundantly grown on crude oil-contaminated soil of oil field situated at upper Assam, India, so that this plant could be used to remediate hydrocarbon from contaminated soil. To evaluate the potentiality of the plant, a pot culture experiment was conducted taking 3 kg of rice field soil mixed with crude oil at a concentration of 10,000 (10 g/kg), 20,000 (20 g/kg), 30,000 (30 g/kg), 40,000 (40 g/kg), 50,000 (50 g/kg), 60,000 (60 g/kg), 70,000 (70 g/kg), 80,000 (80 g/kg), 90,000 (90 g/kg), and 100,000 (100 g/kg) ppm. Ten numbers of healthy seeds of C. pallida were sown in three pots of each concentration for germination, and after 15 days of germination, single healthy seedling in each pot was kept for the study. A control setup was also maintained without adding crude oil. The duration of the experiment was fixed for 6 months. The results showed that uptake of hydrocarbon by the plants was increased with increasing the concentration of crude oil in the soil up to 60,000 ppm. After that, uptake of hydrocarbon by the plants was found to be lower with increasing doses of crude oil concentration. Uptake of hydrocarbon by the shoot was found to be maximum, i.e., 35,018 ppm in 60,000 ppm concentration. Dissipation of total petroleum hydrocarbon (TPH) from the soil was also gradually increased with increasing concentration of crude oil in the soil up to 60,000 ppm. Maximum dissipation, i.e., 78.66 %, occurred in 60,000 ppm concentration of crude oil-mixed soil. The plant could not survive in 100,000 ppm concentration of crude oil-mixed soil. The results also demonstrated that there was a reduction in plant shoot and root biomass with an increase of crude oil concentration. Furthermore, results revealed that the shoot biomass was higher than root biomass in all the treatments.

Attenuation of the anti-contractile effect of cooling in the rat aorta by perivascular adipose tissue.

PubMed

Rafique, Y; AlBader, M; Oriowo, M

2017-09-01

In addition to providing mechanical support for blood vessels, the perivascular adipose tissue (PVAT) secretes a number of vasoactive substances and exerts an anticontractile effect. The main objective of this study was to find out whether the anticontractile effect of cooling in the rat aorta is affected by PVAT. Our hypothesis was that PVAT would enhance the anticontractile effect of cooling in the rat aorta. Aorta segments, with or without PVAT, were used in this investigation. Cumulative concentration-response curves were established for phenylephrine at 37°C or 24°C. Phenylephrine (10 -9 M - 10 -5 M) induced concentration-dependent contractions of aorta segments with or without PVAT at 37°C. The maximum response, but not pD 2 value, was reduced in aorta segments with PVAT. Cooling the tissues to 24 °C resulted in a significant reduction in the maximum response in aorta segments without PVAT with no change in pD 2 values. However, the anticontractile effect of cooling was attenuated in the presence of PVAT with no significant (p > 0.05) change in either the maximum response or pD 2 value. L-NAME potentiated PE-induced contractions and this was greater in aorta segments without PVAT at both temperatures. The expression of eNOS protein and basal tissue level of nitric oxide (NO) were greater in aorta segments with PVAT at both temperatures. However, PE significantly increased tissue levels of NO only in aorta segments without PVAT. We concluded that PVAT-induced loss of anticontractile effect of cooling against PE-induced contractions could be due to impaired generation of NO in aorta segments with PVAT. © 2017 John Wiley & Sons Ltd.

Biological Effects of Short, High-Level Exposure to Gases: Carbon Monoxide.

DTIC Science & Technology

1980-06-01

Selection of maximum allowable concentrations for use in the military should be based more appropriately on considerations of casualty prevention (i.e...base selection of maximum allow- able concentrations for use in the military upon considerations of casualty prevention (i.e., immediate incapacitation...which is reversible, and that no injury will result from the exposure. Persons with myocardial disease are expected to be the most susceptible. These

The correlation of the maximum intensity of fluorescence with pigment characteristics of leaves of Betula pendula

NASA Astrophysics Data System (ADS)

Zavoruev, V. V.; Zavorueva, E. N.

2015-11-01

Using fluorimeter Junior PAM (Heinz Walz GmbH, Germany) the fluorescence parameters of leaves of Betula pendula are investigated. A linear dependence of the maximum fluorescence (Fm) of leaves from the ratio of total chlorophylls concentration to concentration of carotenoids is obtained. Such dependence is found for samples collected during the period of vegetation and for simultaneous selection of colored leaves.

Ozone exposures and implications for vegetation in rural areas of the central Appalachian Mountains, U.S.A.

Treesearch

Pamela Edwards; Cindy Huber; Frederica Wood

2004-01-01

The United States is making the transition from the 1979 1 hr maximum ozone standard to the newly adopted 8 hr ozone standard (3 yr average of the 4th highest maximum 8 hr ozone concentration). Consequently, we analyzed and compared ozone concentrations under both standards from a variety of monitoring sites throughout the central Appalachian region of Kentucky (KY),...

Biological measure of compliance to Artesunate plus Amodiaquine association: interest in a Mono-Desethyl-Amodiaquine blood assay?

PubMed

Sarrassat, Sophie; Sakho, Madiagne; Le Hesran, Jean Yves

2009-04-01

The deployment of Artemisinin-based Combination Therapy for treating uncomplicated malaria poses problems in the patient compliance to these new treatments. The aim of our study was to investigate the relationship between compliance to 3 days treatment with Artesunate plus Amodiaquine (AS+AQ) and the Mono-Desethyl-Amodiaquine (MDA) blood concentration on the fourth day. A reference scale of mean MDA blood concentrations was constructed in 40 healthy adults. Each concentration corresponded to the MDA level on day 3 in a subject having one of the seven compliance degrees defined by the number and sequence of drug intakes from day 0 to day 2: one single dose on day 0, day 1 or day 2; two single doses separated by 24h, on day 0 and day 1 or on day 1 and day 2; two single doses separated by 48 h, on day 0 and day 2; three single doses, on day 0, day 1 and day 2. MDA was assayed in whole blood samples by HPLC. Non-parametric Mann and Whitney U tests were used for the comparison of two means. Our results demonstrated no clear relationship between the mean MDA blood concentrations on day 3 and compliance degrees, according to neither the number nor the sequence of doses taken. In particular, even though the differences were not significant, the mean concentration after three doses, expected to be the maximum, was unexpectedly lower than after two doses, on day 0 and day 1 or on day 1 and day 2. The high inter-individual variability of MDA concentrations attributed to the different rates of hepatic metabolism of each individual appears to have a greater effect on MDA levels than the number or timing of doses. Therefore, it seems that the role of a MDA blood assay is limited in use to discerning if none or one or more doses have been taken. A MDA assay do not allow to measure the compliance degree of one patient to AS+AQ association. Presently, interview and pill count following treatment seem to be the only tools available that may permit differentiation between degrees of compliance.

Temporal and spatial variation of maximum wind speed days during the past 20 years in major cities of Xinjiang

NASA Astrophysics Data System (ADS)

Baidourela, Aliya; Jing, Zhen; Zhayimu, Kahaer; Abulaiti, Adili; Ubuli, Hakezi

2018-04-01

Wind erosion and sandstorms occur in the neighborhood of exposed dust sources. Wind erosion and desertification increase the frequency of dust storms, deteriorate air quality, and damage the ecological environment and agricultural production. The Xinjiang region has a relatively fragile ecological environment. Therefore, the study of the characteristics of maximum wind speed and wind direction in this region is of great significance to disaster prevention and mitigation, the management of activated dunes, and the sustainable development of the region. Based on the latest data of 71 sites in Xinjiang, this study explores the temporal evolution and spatial distribution of maximum wind speed in Xinjiang from 1993 to 2013, and highlights the distribution of annual and monthly maximum wind speed and the characteristics of wind direction in Xinjiang. Between 1993 and 2013, Ulugchat County exhibited the highest number of days with the maximum wind speed (> 17 m/s), while Wutian exhibited the lowest number. In Xinjiang, 1999 showed the highest number of maximum wind speed days (257 days), while 2013 showed the lowest number (69 days). Spring and summer wind speeds were greater than those in autumn and winter. There were obvious differences in the direction of maximum wind speed in major cities and counties of Xinjiang. East of the Tianshan Mountains, maximum wind speeds are mainly directed southeast and northeast. North and south of the Tianshan Mountains, they are mainly directed northwest and northeast, while west of the Tianshan Mountains, they are mainly directed southeast and northwest.

Study and Search for Main Reason of Lung Cancers Based on Cherenkov Radiation in Environmental Radiation

NASA Astrophysics Data System (ADS)

Ito, Hiroshi; Emoto, Yusaku; Fujihara, Kento; Kawai, Hideyuki; Kimura, Shota; Kodama, Satoshi; Mizuno, Takahiro

2018-01-01

The number of lung-cancer-related death is highest among all cancers in the world, and it is increasing in Japan where population aging in progressing. The main reason for the lung cancer of non-smokers is regarded to be environmental pollution or exposure of the lung to radon in the nature. The risk of lung cancer was estimated to increase by 8 to 13% per every 100 Bq m-3 concentration of radon in the air. We observed beta rays with maximum energy of 3.27 MeV emitted from 214Bi as one of the progenies based on a detection of Cherenkov radiation. The surface radioactivity concentration of 214Bi on the sample was measured; the relation between the concentration and exposure time for the sample at the room air is researched. The behavior of the radon progenies in the air is discussed by a research for the progenies attaching on the sample after the radon decay. The inhalation of the radon progenies is not clear. Thus, to understand the behavior of progenies in the air make to clear the causal relation between the radon concentration and lung cancers.

Effect of land use and hydrological processes on Escherichia coli concentrations in streams of tropical, humid headwater catchments.

PubMed

Rochelle-Newall, Emma J; Ribolzi, Olivier; Viguier, Marion; Thammahacksa, Chanthamousone; Silvera, Norbert; Latsachack, Keooudone; Dinh, Rinh Pham; Naporn, Piyapong; Sy, Hai Tran; Soulileuth, Bounsamay; Hmaimum, Nikom; Sisouvanh, Pem; Robain, Henri; Janeau, Jean-Louis; Valentin, Christian; Boithias, Laurie; Pierret, Alain

2016-09-08

Lack of access to clean water and adequate sanitation continues to be a major brake on development. Here we present the results of a 12-month investigation into the dynamics of Escherichia coli, a commonly used indicator of faecal contamination in water supplies, in three small, rural catchments in Laos, Thailand and Vietnam. We show that land use and hydrology are major controlling factors of E. coli concentrations in streamwater and that the relative importance of these two factors varies between the dry and wet seasons. In all three catchments, the highest concentrations were observed during the wet season when storm events and overland flow were highest. However, smaller peaks of E. coli concentration were also observed during the dry season. These latter correspond to periods of intense farming activities and small, episodic rain events. Furthermore, vegetation type, through land use and soil surface crusting, combined with mammalian presence play an important role in determining E. coli loads in the streams. Finally, sampling during stormflow revealed the importance of having appropriate sampling protocols if information on maximum contamination levels is required as grab sampling at a fixed time step may miss important peaks in E. coli numbers.

Effect of land use and hydrological processes on Escherichia coli concentrations in streams of tropical, humid headwater catchments

NASA Astrophysics Data System (ADS)

Rochelle-Newall, Emma J.; Ribolzi, Olivier; Viguier, Marion; Thammahacksa, Chanthamousone; Silvera, Norbert; Latsachack, Keooudone; Dinh, Rinh Pham; Naporn, Piyapong; Sy, Hai Tran; Soulileuth, Bounsamay; Hmaimum, Nikom; Sisouvanh, Pem; Robain, Henri; Janeau, Jean-Louis; Valentin, Christian; Boithias, Laurie; Pierret, Alain

2016-09-01

Lack of access to clean water and adequate sanitation continues to be a major brake on development. Here we present the results of a 12-month investigation into the dynamics of Escherichia coli, a commonly used indicator of faecal contamination in water supplies, in three small, rural catchments in Laos, Thailand and Vietnam. We show that land use and hydrology are major controlling factors of E. coli concentrations in streamwater and that the relative importance of these two factors varies between the dry and wet seasons. In all three catchments, the highest concentrations were observed during the wet season when storm events and overland flow were highest. However, smaller peaks of E. coli concentration were also observed during the dry season. These latter correspond to periods of intense farming activities and small, episodic rain events. Furthermore, vegetation type, through land use and soil surface crusting, combined with mammalian presence play an important role in determining E. coli loads in the streams. Finally, sampling during stormflow revealed the importance of having appropriate sampling protocols if information on maximum contamination levels is required as grab sampling at a fixed time step may miss important peaks in E. coli numbers.

Methods of Statistical Control for Groundwater Quality Indicators

NASA Astrophysics Data System (ADS)

Yankovich, E.; Nevidimova, O.; Yankovich, K.

2016-06-01

The article describes the results of conducted groundwater quality control. Controlled quality indicators included the following microelements - barium, manganese, iron, mercury, iodine, chromium, strontium, etc. Quality control charts - X-bar chart and R chart - were built. For the upper and the lower threshold limits, maximum permissible concentration of components in water and the lower limit of their biologically significant concentration, respectively, were selected. The charts analysis has shown that the levels of microelements content in water at the area of study are stable. Most elements in the underground water are contained in concentrations, significant for human organisms consuming the water. For example, such elements as Ba, Mn, Fe have concentrations that exceed maximum permissible levels for drinking water.

Ground-water quality in the West Salt River Valley, Arizona, 1996-98: relations to hydrogeology, water use, and land use

USGS Publications Warehouse

Edmonds, Robert J.; Gellenbeck, Dorinda J.

2002-01-01

The U.S. Geological Survey collected and analyzed ground-water samples in the West Salt River Valley from 64 existing wells selected by a stratified-random procedure. Samples from an areally distributed group of 35 of these wells were used to characterize overall ground-water quality in the basin-fill aquifer. Analytes included the principal inorganic constituents, trace constituents, pesticides, and volatile organic compounds. Additional analytes were tritium, radon, and stable isotopes of hydrogen and oxygen. Analyses of replicate samples and blank samples provided evidence that the analyses of the ground-water samples were adequate for interpretation. The median concentration of dissolved solids in samples from the 35 wells was 560 milligrams per liter, which exceeded the U.S. Environmental Protection Agency Secondary Maximum Contaminant Level for drinking water. Eleven of the 35 samples had a nitrate concentration (as nitrogen) that exceeded the U.S. Environmental Protection Agency Maximum Contaminant Level for drinking water of 10 milligrams per liter. Pesticides were detected in eight samples; concentrations were below the Maximum Contaminant Levels. Deethylatrazine was most commonly detected. The pesticides were detected in samples from wells in agricultural or urban areas that have been irrigated. Concentrations of all trace constituents, except arsenic, were less than the Maximum Contaminant Levels. The concentration of arsenic exceeded the Maximum Contaminant Level of 50 micrograms per liter in two samples. Nine monitoring wells were constructed in an area near Buckeye to assess the effects of agricultural land use on shallow ground water. The median concentration of dissolved solids was 3,340 milligrams per liter in samples collected from these wells in August 1997. The nitrate concentration (as nitrogen) exceeded the Maximum Contaminant Level (10 milligrams per liter) in samples from eight of the nine monitoring wells in August 1997 and again in February 1998. Analyses of all samples collected from the monitoring wells indicated low concentrations of pesticides and volatile organic compounds. The most frequently detected pesticides were deethylatrazine and atrazine. Trichloromethane (chloroform) and tetrachloroethene (PCE) were the most frequently detected volatile organic compounds in the monitoring wells. Two compounds [dieldrin and 1,1-dichloro-2,2-bis(p-dichlorodiphenyl)ethylene (DDE)], decomposition products of two banned pesticides, aldrin and dichlorodiphenylethylene (DDT), were detected at low concentrations in samples analyzed for the agricultural land-use study. In the West Salt River Valley, a high concentration of the heavier oxygen isotope?oxygen-18?in ground water generally indicates effects of evaporation on recharge water from irrigation. Wells in undeveloped areas and wells that have openings beneath a confining bed generally yield ground water that is free of the effects of irrigation seepage. Samples from these wells did not contain detectable concentrations of pesticides. The median concentrations of nitrate (as nitrogen) and dissolved solids in samples from wells in undeveloped areas were 1.7 milligrams per liter and 257 milligrams per liter, respectively. The median concentrations of nitrate (as nitrogen) and dissolved solids in samples from wells that yield water from below confining beds were 2.0 and 747 milligrams per liter, respectively.

Past, present and future concentrations of ground-level ozone and potential impacts on ecosystems and human health in northern Europe.

PubMed

Karlsson, Per Erik; Klingberg, Jenny; Engardt, Magnuz; Andersson, Camilla; Langner, Joakim; Karlsson, Gunilla Pihl; Pleijel, Håkan

2017-01-15

This review summarizes new information on the current status of ground-level ozone in Europe north of the Alps. There has been a re-distribution in the hourly ozone concentrations in northern Europe during 1990-2015. The highest concentrations during summer daytime hours have decreased while the summer night-time and winter day- and night-time concentrations have increased. The yearly maximum 8-h mean concentrations ([O 3 ] 8h,max ), a metric used to assess ozone impacts on human health, have decreased significantly during 1990-2015 at four out of eight studied sites in Fennoscandia and northern UK. Also the annual number of days when the yearly [O 3 ] 8h,max exceeded the EU Environmental Quality Standard (EQS) target value of 60ppb has decreased. In contrast, the number of days per year when the yearly [O 3 ] 8h,max exceeded 35ppb has increased significantly at two sites, while it decreased at one far northern site. [O 3 ] 8h,max is predicted not to exceed 60ppb in northern UK and Fennoscandia after 2020. However, the WHO EQS target value of 50ppb will still be exceeded. The AOT40 May-July and AOT40 April-September metrics, used for the protection of vegetation, have decreased significantly at three and four sites, respectively. The EQS for the protection of forests, AOT40 April-September 5000ppbh, is projected to no longer be exceeded for most of northern Europe sometime before the time period 2040-2059. However, if the EQS is based on Phytotoxic Ozone Dose (POD), POD 1 , it may still be exceeded by 2050. The increasing trend for low and medium range ozone concentrations in combination with a decrease in high concentrations indicate that a new control strategy, with a larger geographical scale than Europe and including methane, is needed for ozone abatement in northern Europe. Copyright © 2016 Elsevier B.V. All rights reserved.

Polychlorinated dibenzo-p-dioxins and dibenzofurans in the atmosphere around the Great Lakes.

PubMed

Venier, Marta; Ferrario, Joseph; Hites, Ronald A

2009-02-15

The atmospheric concentrations of PCDDs and PCDFs were measured in four sites near the shores of the North American Great Lakes. The sites included an urban site (Chicago, Illinois) and three rural/remote sites (Eagle Harbor, Michigan; Sleeping Bear Dunes, Michigan; and Sturgeon Point, New York). Sampling occurred every 24 days between November 2004 and December 2007. The concentration of PCDD/Fs averaged 2.3 +/- 0.2 fg WHO TEQ/m3 at Eagle Harbor, 35 +/- 3 fg WHO TEO/ m3 at Chicago, 7.4 +/- 1.4 fg WHO TEO/m3 at Sleeping Bear Dunes, and 13 +/- 2 fg WHO TED/m3 at Sturgeon Point. The total concentration of the 17 toxic PCDD/F congeners showed a significant seasonal trend at all sites, except Chicago. The date of maximum concentration averaged Dec 6 +/- 35 days, which is consistent with residential heating being an important source of PCDD/Fs to the atmosphere. A significant positive relationship between the logarithm of the total concentration of the 17 toxic PCDD/F congeners and the logarithm of the number of people within a 25 km radius around the sampling site was found. We suggest that urban and industrial areas, which are heavily populated, act as sources of PCDDs and PCDFs to the atmosphere.

Risk Assessment of Florists Exposed to Pesticide Residues through Handling of Flowers and Preparing Bouquets.

PubMed

Toumi, Khaoula; Joly, Laure; Vleminckx, Christiane; Schiffers, Bruno

2017-05-13

Flowers are frequently treated with pesticides and, as a result, florists handling daily a large number of flowers can be exposed to pesticide residues. A study was conducted among twenty volunteer florists located in Namur Province and in the Brussels Capital Region of Belgium in order to assess their potential dermal exposure to dislodgeable pesticide residues transferred from flowers to hands. Two pairs of cotton gloves were worn during two consecutive half days while handling flowers and preparing bouquets (from min 2 h to max 3 h/day). The residual pesticide deposits on the glove samples were extracted with a multi-residue Quick Easy Cheap Effective Rugged Safe (QuEChERS) method and analyzed by a combination of gas and liquid chromatography tandem mass spectrometry (GC-MS/MS and LC-MS/MS) by an accredited laboratory. A total of 111 active substances (mainly insecticides and fungicides) were detected, with an average of 37 active substances per sample and a total concentration per glove sample of 22.22 mg/kg. Several predictive levels of contamination were considered to assess the risk. The potential dermal exposures (PDE) of florists were estimated at the average, for different percentiles, and at the maximum concentration of residues in samples. At the PDE P90 and at the PDE MAX (or worst case) values, three and five active substances respectively exceed the Acceptable Operator Exposure Level (AOEL), indicating risk situations. For the systemic exposure (SE), one active substance (clofentezine) exceeds the AOEL at the P90 predictive level. In the worst case, SE MAX (at the maximum concentrations), four active substances (clofentezine, famoxadone, methiocarb, and pyridaben) exceed their respective AOEL values. Among the 14 most frequently detected active substances, two have SE MAX values exceeding the AOEL. Exposure could be particularly critical for clofentezine with an SE MAX value four times higher than the AOEL (393%). The exposure of florists appeared to be an example of a unique professional situation in which workers are exposed regularly to both a very high number of toxic chemicals and rather high concentration levels. Therefore the priority should be to raise the level of awareness among the florists who must change their habits and practices if they want to minimize their exposure.

Risk Assessment of Florists Exposed to Pesticide Residues through Handling of Flowers and Preparing Bouquets

PubMed Central

Toumi, Khaoula; Joly, Laure; Vleminckx, Christiane; Schiffers, Bruno

2017-01-01

Flowers are frequently treated with pesticides and, as a result, florists handling daily a large number of flowers can be exposed to pesticide residues. A study was conducted among twenty volunteer florists located in Namur Province and in the Brussels Capital Region of Belgium in order to assess their potential dermal exposure to dislodgeable pesticide residues transferred from flowers to hands. Two pairs of cotton gloves were worn during two consecutive half days while handling flowers and preparing bouquets (from min 2 h to max 3 h/day). The residual pesticide deposits on the glove samples were extracted with a multi-residue Quick Easy Cheap Effective Rugged Safe (QuEChERS) method and analyzed by a combination of gas and liquid chromatography tandem mass spectrometry (GC-MS/MS and LC-MS/MS) by an accredited laboratory. A total of 111 active substances (mainly insecticides and fungicides) were detected, with an average of 37 active substances per sample and a total concentration per glove sample of 22.22 mg/kg. Several predictive levels of contamination were considered to assess the risk. The potential dermal exposures (PDE) of florists were estimated at the average, for different percentiles, and at the maximum concentration of residues in samples. At the PDE P90 and at the PDEMAX (or worst case) values, three and five active substances respectively exceed the Acceptable Operator Exposure Level (AOEL), indicating risk situations. For the systemic exposure (SE), one active substance (clofentezine) exceeds the AOEL at the P90 predictive level. In the worst case, SEMAX (at the maximum concentrations), four active substances (clofentezine, famoxadone, methiocarb, and pyridaben) exceed their respective AOEL values. Among the 14 most frequently detected active substances, two have SEMAX values exceeding the AOEL. Exposure could be particularly critical for clofentezine with an SEMAX value four times higher than the AOEL (393%). The exposure of florists appeared to be an example of a unique professional situation in which workers are exposed regularly to both a very high number of toxic chemicals and rather high concentration levels. Therefore the priority should be to raise the level of awareness among the florists who must change their habits and practices if they want to minimize their exposure. PMID:28505067

Application of health-based screening levels to ground-water quality data in a state-scale pilot effort

USGS Publications Warehouse

Toccalino, Patricia L.; Norman, Julia E.; Phillips, Robyn H.; Kauffman, Leon J.; Stackelberg, Paul E.; Nowell, Lisa H.; Krietzman, Sandra J.; Post, Gloria B.

2004-01-01

A state-scale pilot effort was conducted to evaluate a Health-Based Screening Level (HBSL) approach developed for communicating findings from the U.S. Geological Survey (USGS) National Water-Quality Assessment Program in a human-health context. Many aquifers sampled by USGS are used as drinking-water sources, and water-quality conditions historically have been assessed by comparing measured contaminant concentrations to established drinking-water standards and guidelines. Because drinking-water standards and guidelines do not exist for many analyzed contaminants, HBSL values were developed collaboratively by the USGS, U.S. Environmental Protection Agency (USEPA), New Jersey Department of Environmental Protection, and Oregon Health & Science University, using USEPA toxicity values and USEPA Office of Water methodologies. The main objective of this report is to demonstrate the use of HBSL approach as a tool for communicating water-quality data in a human-health context by conducting a retrospective analysis of ground-water quality data from New Jersey. Another important objective is to provide guidance on the use and interpretation of HBSL values and other human-health benchmarks in the analyses of water-quality data in a human-health context. Ground-water samples collected during 1996-98 from 30 public-supply, 82 domestic, and 108 monitoring wells were analyzed for 97 pesticides and 85 volatile organic compounds (VOCs). The occurrence of individual pesticides and VOCs was evaluated in a human-health context by calculating Benchmark Quotients (BQs), defined as ratios of measured concentrations of regulated compounds (that is, compounds with Federal or state drinking-water standards) to Maximum Contaminant Level (MCL) values and ratios of measured concentrations of unregulated compounds to HBSL values. Contaminants were identified as being of potential human-health concern if maximum detected concentrations were within a factor of 10 of the associated MCL or HBSL (that is, maximum BQ value (BQmax) greater than or equal to 0.1) in any well type (public supply, domestic, monitoring). Most (57 of 77) pesticides and VOCs with human-health benchmarks were detected at concentrations well below these levels (BQmax less than 0.1) for all three well types; however, BQmax values ranged from 0.1 to 3,000 for 6 pesticides and 14 VOCs. Of these 20 contaminants, one pesticide (dieldrin) and three VOCs (1,2-dibromoethane, tetrachloroethylene, and trichloroethylene) both (1) were measured at concentrations that met or exceeded MCL or HBSL values, and (2) were detected in more than 10 percent of samples collected from raw ground water used as sources of drinking water (public-supply and (or) domestic wells) and, therefore, are particularly relevant to human health. The occurrence of multiple pesticides and VOCs in individual wells also was evaluated in a human-health context because at least 53 different contaminants were detected in each of the three well types. To assess the relative human-health importance of the occurrence of multiple contaminants in different wells, the BQ values for all contaminants in a given well were summed. The median ratio of the maximum BQ to the sum of all BQ values for each well ranged from 0.83 to 0.93 for all well types, indicating that the maximum BQ makes up the majority of the sum for most wells. Maximum and summed BQ values were statistically greater for individual public-supply wells than for individual domestic and monitoring wells. The HBSL approach is an effective tool for placing water-quality data in a human-health context. For 79 of the 182 compounds analyzed in this study, no USEPA drinking-water standards or guidelines exist, but new HBSL values were calculated for 39 of these 79 compounds. The new HBSL values increased the number of detected pesticides and VOCs with human-health benchmarks from 65 to 77 (of 97 detected compounds), thereby expanding the basis for interpreting contaminant-occu

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fritz, Brad G.; Dirkes, Roger L.; Napier, Bruce A.

The Hanford Reach National Monument (HRNM) was created by presidential proclamation in 2000. It is located along the Columbia River in south central Washington and consists of five distinct units. The McGee Ranch-Riverlands and the North Slope units are addressed in this report. North Slope refers to two of the HRNM units: the Saddle Mountain Unit and the Wahluke Slope Unit. The Saddle Mountain and Wahluke Slope Units are located north of the Columbia River, while the McGee Ranch-Riverlands Unit is located south of the Columbia River and north and west of Washington State Highway 24. To fulfill internal U.S.more » Department of Energy (DOE) requirements prior to any radiological clearance of land, the DOE must evaluate the potential for residual radioactive contamination on this land and determine compliance with the requirements of DOE Order 5400.5. Authorized limits for residual radioactive contamination were developed based on the DOE annual exposure limit to the public (100 mrem) using future potential land-use scenarios. The DOE Office of Environmental Management approved these authorized limits on March 1, 2004. Historical soil monitoring conducted on and around the HRNM indicated soil concentrations of radionuclides were well below the authorized limits (Fritz et al. 2003). However, the historical sampling was done at a limited number of sampling locations. Therefore, additional soil sampling was conducted to determine if the concentrations of radionuclides in soil on the McGee Ranch-Riverlands and North Slope units were below the authorized limits. Sixty-seven soil samples were collected from the McGee Ranch-Riverlands and North Slope units. A software package (Visual Sample Plan) was used to plan the collection to assure an adequate number of samples were collected. The number of samples necessary to decide with a high level of confidence (99%) that the soil concentrations of radionuclides on the North Slope and McGee Ranch-Riverlands units did not exceed the authorized limits was determined to be 27. Additional soil samples were collected from areas suspected to have a potential for accumulation of radionuclides. This included samples collected from the riparian zone along the Columbia River, Savage Island, and other locations across the North Slope and McGee Ranch-Riverlands units. The 67 soil samples collected from the McGee Ranch-Riverlands and North Slope units all had concentrations of radionuclides far below the authorized limits established by the DOE. Statistical analysis of the results concluded that the Authorized Limits were not exceeded when total uncertainty was considered. The calculated upper confidence limit for each radionuclide measured in this study (which represents the value at which 99% of the measurements reside below with a 99% confidence level) was lower than the Authorized Limit for each radionuclide. The maximum observed soil concentrations for the radionuclides included in the authorized limits would result in a potential annual dose of 0.23 mrem assuming the most probable use scenario, a recreational visitor. This potential dose is well below the DOE 100-mrem/year dose limit for members of the public. Furthermore, the results of the biota dose assessment screen, which used the RESRAD biota code, indicated that the sum of fractions is less than one. This assumed soil concentrations equal to the maximum concentrations of radionuclides measured on the McGee Ranch-Riverlands and North Slope units’ in this study. Since the sum of fractions was less than 1, dose to terrestrial biota will not exceed the recommended biota dose limit for the soil concentrations measured in this study.« less

Safety Assessment of Nitrocellulose and Collodion as Used in Cosmetics.

PubMed

Fiume, Monice M; Bergfeld, Wilma F; Belsito, Donald V; Hill, Ronald A; Klaassen, Curtis D; Liebler, Daniel C; Marks, James G; Shank, Ronald C; Slaga, Thomas J; Snyder, Paul W; Andersen, F Alan

2016-07-01

The Cosmetic Ingredient Review Expert Panel (the Panel) assessed the safety of nitrocellulose and collodion as used in cosmetics, concluding that these ingredients are safe in the present practices of use and concentration in cosmetic formulations. Both ingredients are used almost exclusively in nail product formulations. The maximum concentration of use of nitrocellulose in nail polish and enamels is 22%; for collodion, the maximum reported concentration of use in nail polish and enamel is 14%. The Panel reviewed available animal and clinical data in making its determination of safety. © The Author(s) 2016.

Improved fed-batch production of high-purity PHB (poly-3 hydroxy butyrate) by Cupriavidus necator (MTCC 1472) from sucrose-based cheap substrates under response surface-optimized conditions.

PubMed

Dey, Pinaki; Rangarajan, Vivek

2017-10-01

Experimental investigations were carried out for Cupriavidus necator (MTCC 1472)-based improved production of poly-3 hydroxy butyrate (PHB) through induced nitrogen limiting fed-batch cultivation strategies. Initially Plackett-Burman design and response surface methodology were implemented to optimize most influencing process parameters. With optimized process parameter values, continuous feeding strategies ware applied in a 5-l fermenter with table sugar concentration of 100 g/l, nitrogen concentration of 0.12 g/l for fed-batch fermentation with varying dilution rates of 0.02 and 0.046 1/h. To get enriched production of PHB, concentration of the sugar was further increased to 150 and 200 g/l in feeding. Maximum concentrations of PHB achieved were 22.35 and 23.07 g/l at those dilution rates when sugar concentration maintains at 200 g/l in feeding. At maximum concentration of PHB (23.07 g/l), productivity of 0.58 g/l h was achieved with maximum PHB accumulation efficiency up to 64% of the dry weight of biomass. High purity of PHB, close to medical grade was achieved after surfactant hypochlorite extraction method, and it was further confirmed by SEM, EDX, and XRD studies.

Effect of agitation rate on ethanol production from sugar maple hemicellulosic hydrolysate by Pichia stipitis.

PubMed

Shupe, Alan M; Liu, Shijie

2012-09-01

Concentrated dilute acid hydrolysate was obtained from hot water extracts of Acer saccharum (sugar maple) and was fermented to ethanol by Pichia stipitis in a 1.3-L-benchtop bioreactor. The conditions under which the highest ethanol yield was achieved were when the air flow rate was set to 100 cm(3) and the agitation rate was set to 150 rpm resulting in an overall mass transfer coefficient (K(L)a) of 0.108 min(-1). A maximum ethanol concentration of 29.7 g/L was achieved after 120 h of fermentation; however, after 90 h of fermentation, the ethanol concentration was only slightly lower at 29.1 g/L with a yield of 0.39 g ethanol per gram of sugar consumed. Using the same air flow rate and adjusting the agitation rate resulted in lower ethanol yields of 0.25 g/g at 50 rpm and 0.30 g/g at 300 rpm. The time it takes to reach the maximum ethanol concentration was also affected by the agitation rate. The ethanol concentration continued to increase even after 130 h of fermentation when the agitation rate was set at 50 rpm, whereas the maximum ethanol concentration was reached after only 68.5 h at 300 rpm.

Occurrence and distribution of selected contaminants in public drinking-water supplies in the surficial aquifer in Delaware

USGS Publications Warehouse

Ferrari, Matthew J.

2001-01-01

Water samples were collected from August through November 2000 from 30 randomly selected public drinking-water supply wells screened in the unconfined aquifer in Delaware, and analyzed to assess the occurrence and distribution of selected pesticide compounds, volatile organic compounds, major inorganic ions, and nutrients. Water from a subset of 10 wells was sampled and analyzed for radium and radon. The average age of ground water entering the well screens in all the wells was determined to be generally less than 20 years. Low concentrations of pesticide compounds and volatile organic compounds were detected throughout the State of Delaware, with several compounds often detected in each water sample. Pesticide and metabolite (pesticide degradation products) concentrations were generally less than 1 microgram per liter, and were detected in sam-ples from 27 of 30 wells. Of the 45 pesticides and 13 metabolites analyzed, 19 compounds (13 pesticides and 6 metabolites) were detected in at least 1 of the 30 samples. Desethylatrazine, alachlor ethane sulfonic acid, metolachlor ethane sulfonic acid, metolachlor, and atrazine were the most frequently detected pesticide compounds, and were present in at least half the samples. None of the pesticide detections was above the U.S. Environmental Protection Agency's Primary Maximum Contaminant Levels or Health Advisories. Volatile organic compounds also were present at low concentrations (generally less than 1 microgram per liter) in samples from all 30 wells. Of the 85 volatile organic com-pounds analyzed, 34 compounds were detected in at least 1 of the 30 samples. Chloroform, tetrachloroethene, and methyl tert-butyl ether were the most frequently detected volatile organic compounds, and were found in at least half the samples. None of the volatile organic compound detections was above U.S. Environmental Protection Agency's Primary Maximum Contaminant Levels or Health Advisories. A few samples contained compounds with concentrations above the U.S. Environmental Protection Agency's Primary Maximum Contaminant Levels or Secondary Maximum Contaminant Levels for inorganic compounds and radionuclides. One sample out of 30 contained a concentration of nitrite plus nitrate above the U.S. Environmental Protection Agency's Primary Maximum Contaminant Level of 10 milligrams per liter as nitrogen. Iron and manganese concentrations above the U.S. Environmental Protection Agency's Secondary Maximum Contaminant Levels were found in 7 of 30 ground-water samples, most of them from Sussex County. In the 10 wells sampled for radionuclides, only one sample had detectable levels of radium-224 and -226, and another sample contained detectable levels of radium-228; both of these samples also had detectable gross-alpha and gross-beta activities. None of these activities were above the U.S. Environ-mental Protection Agency's Primary Maximum Contaminant Levels or Secondary Maximum Contaminant Levels. Radon was detected in all 10 samples, but was above the current U.S. Environmental Protection Agency's proposed Primary Maximum Contaminant Level of 300 picocuries per liter in only one sample.

Adsorption of amphipathic dendrons on polystyrene nanoparticles.

PubMed

Sakthivel, T; Florence, A T

2003-03-18

Adsorption of dendrons onto nanoparticles may provide new model structures which may be useful in drug and gene delivery. Tritiated amphipathic dendrons having three lipidic (C(14)) chains coupled to branched (dendritic) lysine head groups with 8, 16 or 32 free terminal amino groups have been synthesised by solid phase peptide techniques. The interaction between these tritiated dendrons and 200 nm polystyrene latex nanoparticles was investigated in phosphate buffered saline. The amount of dendron adsorbed increased with increasing concentration of dendrons and then decreased. Maximum adsorption of dendrons per gram of nanoparticles was found to be between 8.2 and 84 x 10(-6)M, the amounts adsorbed being inversely proportional to the number of amino groups present in the molecule. The number of dendron molecules adsorbed per nanoparticle was found to be between 430 and 4421. The degree of adsorption was found to be slightly altered by the temperature. Copyright 2002 Elsevier Science B.V.

Spacecraft Maximum Allowable Concentrations for Selected Airborne Contaminants. Volume 5

NASA Technical Reports Server (NTRS)

2008-01-01

To protect space crews from air contaminants, NASA requested that the National Research Council (NRC) provide guidance for developing spacecraft maximum allowable concentrations (SMACs) and review NASA's development of exposure guidelines for specific chemicals. The NRC convened the Committee on Spacecraft Exposure Guidelines to address this task. The committee published Guidelines for Developing Spacecraft Maximum Allowable Concentrations for Space Station Contaminants (NRC 1992). The reason for the review of chemicals in Volume 5 is that many of them have not been examined for more than 10 years, and new research necessitates examining the documents to ensure that they reflect current knowledge. New knowledge can be in the form of toxicologic data or in the application of new approaches for analysis of available data. In addition, because NASA anticipates longer space missions beyond low Earth orbit, SMACs for 1,000-d exposures have also been developed.

Opinion of the Scientific Committee on Consumer Safety (SCCS) - Revision of the opinion on o-Phenylphenol, Sodium o-phenylphenate and Potassium o-phenylphenate (OPP), in cosmetic products.

PubMed

Bernauer, Ulrike

2016-08-01

o-Phenylphenol, Sodium o-phenylphenate, Potassium o-phenylphenate, CAS n. 90-43-7, 132-27-4, 13707-65-8 as preservatives are regulated in Annex V/7 of the Cosmetics Regulation (EC) n. 1223/2009 at a maximum concentration of 0.2% (as phenol). In February 2013, the Commission received a risk assessment submitted by the French Agency ANSM (Agence nationale de sécurité des médicaments et des produits de santé) which rose concerns about the use of o-Phenylphenol as preservatives in cosmetic products. In the context of the ANSM report (Evaluation du risque lié à l'utilisation de l'orthophénylphénol CAS n. 90-43-7 dans les produits cosmétiques) o-Phenylphenol has been identified as likely to be an endocrine disruptor. The report concludes that the maximum authorised concentration (currently of 0.2%) of o-Phenylphenol for use as a preservative should be revised due to low margin of safety. In January 2014, in response to a call for data on o-Phenylphenol by the Commission, Industry submitted a safety dossier in order to defend the current use of o-Phenylphenol, Sodium o-phenylphenate, Potassium o-phenylphenate, CAS n. 90-43-7, 132-27-4, 13707- 65-8 as preservatives in cosmetic formulations at a maximum concentration of 0.2% (as phenol). o-Phenylphenol as preservative with a maximum concentration of 0.2% in leave-on cosmetic products is not safe. Also, in view of further exposures including noncosmetic uses (see Anses, 2014), the maximum concentration of o-Phenylphenol in leave-on cosmetic products should be lowered. However, the proposed maximum use concentration of up to 0.15% by the applicant can be considered safe. The use of o-Phenylphenol as preservative with a maximum concentration of 0.2% in rinse-off cosmetic products is considered safe. Based on the information provided, no conclusions of safe use can be drawn for Sodium o-phenylphenate and Potassium o-phenylphenate. In vitro data indicate an absent or very weak binding affinity of OPP to the oestrogen receptor, in line with limited stimulation of proliferation in oestrogen responsive cells. No information is available on androgenic and anti-androgenic effects of OPP in vitro. Agonistic or antagonistic effects on thyroid hormones were not observed with OPP. There might be a potential of injury to the vision system attributable to OPP. Aggregate exposure to OPP should be considered. Copyright © 2016. Published by Elsevier Inc.

Seasonality of diel cycles of dissolved trace-metal concentrations in a Rocky Mountain stream

USGS Publications Warehouse

Nimick, D.A.; Cleasby, T.E.; McCleskey, R. Blaine

2005-01-01

Substantial diel (24-h) cycles in dissolved (0.1-??m filtration) metal concentrations were observed during summer low flow, winter low flow, and snowmelt runoff in Prickly Pear Creek, Montana. During seven diel sampling episodes lasting 34-61.5 h, dissolved Mn and Zn concentrations increased from afternoon minimum values to maximum values shortly after sunrise. Dissolved As concentrations exhibited the inverse timing. The magnitude of diel concentration increases varied in the range 17-152% for Mn and 70-500% for Zn. Diel increases of As concentrations (17-55%) were less variable. The timing of minimum and maximum values of diel streamflow cycles was inconsistent among sampling episodes and had little relation to the timing of metal concentration cycles, suggesting that geochemical rather than hydrological processes are the primary control of diel metal cycles. Diel cycles of dissolved metal concentrations should be assumed to occur at any time of year in any stream with dissolved metals and neutral to alkaline pH. ?? Springer-Verlag 2005.

Seasonal variation, risk assessment and source estimation of PM 10 and PM10-bound PAHs in the ambient air of Chiang Mai and Lamphun, Thailand.

PubMed

Pengchai, Petch; Chantara, Somporn; Sopajaree, Khajornsak; Wangkarn, Sunanta; Tengcharoenkul, Urai; Rayanakorn, Mongkon

2009-07-01

Daily PM10 concentrations were measured at four sampling stations located in Chiang Mai and Lamphun provinces, Thailand. The sampling scheme was conducted during June 2005 to June 2006; every 3 days for 24 h in each sampling period. The result revealed that all stations shared the same pattern, in which the PM10 (particulate matters with diameter of less than 10 microm) concentration increased at the beginning of dry season (December) and reached its peak in March before decreasing by the end of April. The maximum PM10 concentration for each sampling station was in the range of 140-182 microg/m(3) which was 1.1-1.5 times higher than the Thai ambient air quality standard of 120 microg/m(3). This distinctly high concentration of PM10 in the dry season (Dec. 05-Mar. 06) was recognized as a unique seasonal pattern for the northern part of Thailand. PM10 concentration had a medium level of negative correlation (r = -0.696 to -0.635) with the visibility data. Comparing the maximum PM10 concentration detected at each sampling station to the permitted PM10 level of the national air quality standard, the warning visibility values for the PM10 pollution-watch system were determined as 10 km for Chiang Mai Province and 5 km for Lamphun Province. From the analysis of PM10 constituents, no component exceeded the national air quality standard. The total concentrations of PM10-bond polycyclic aromatic hydrocarbons (PAHs) are calculated in terms of total toxicity equivalent concentrations (TTECs) using the toxicity equivalent factors (TEFs) method. TTECs in Chiang Mai and Lamphun ambient air was found at a level comparable to those observed in Nagasaki, Bangkok and Rome and at a lower level than those reported at Copenhagen. The annual number of lung cancer cases for Chiang Mai and Lamphun Provinces was estimated at two cases/year which was lower than the number of cases in Bangkok (27 cases/year). The principal component analysis/absolute principal component scores (PCA/APCS) model and multiple regression analysis were applied to the PM10 and its constituents data. The results pointed to the vegetative burning as the largest PM10 contributor in Chiang Mai and Lamphun ambient air. Vegetative burning, natural gas burning & coke ovens, and secondary particle accounted for 46-82%, 12-49%, and 3-19% of the PM10 concentrations, respectively. However, natural gas burning & coke ovens as well as vehicle exhaust also deserved careful attention due to their large contributions to PAHs concentration. In the wet season and transition periods, 42-60% of the total PAHs concentrations originated from vehicle exhaust while 16-37% and 14-38% of them were apportioned to natural gas burning & coke ovens and vegetative burning, respectively. In the dry period, natural gas burning & coke ovens, vehicle exhaust, and vegetative burning accounted for 47-59%, 20-25%, and 19-28% of total PAHs concentrations. The close agreement between the measured and predicted concentrations data (R(2) > 0.8) assured enough capability of PCA/APCS receptor model to be used for the PM10 and PAHs source apportionment.

(2-methoxyethoxy)acetic acid: a urinary biomarker of exposure for jet fuel JP-8.

PubMed

B'hymer, Clayton; Mathias, Patricia; Krieg, Edward; Cheever, Kenneth L; Toennis, Christine A; Clark, John C; Kesner, James S; Gibson, Roger L; Butler, Mary Ann

2012-05-01

To demonstrate the utility of the urinary metabolite (2-methoxyethoxy)acetic acid (MEAA) as a biomarker of exposure. 2-(2-methoxyethoxy)ethanol [diethylene glycol monomethyl ether] is an anti-icing agent used in the formulation of JP-8, and it is added at a known uniform 0.1% (v/v) concentration to each batch lot. JP-8 is a kerosene-based fuel containing different compounds that vary in the content of every batch/lot of fuel; thus, MEAA has the potential to be a more specific and a consistent quantitative biomarker for JP-8 exposure. MEAA was used to measure exposure of jet propulsion fuel 8 (JP-8) in United States Air Force (USAF) personnel working at six airbases within the United States. Post-shift urine specimens from various personnel including high (n = 98), moderate (n = 38), and low (n = 61) exposure workgroup categories were collected and analyzed by a gas chromatographic-mass spectrometric test method. The three exposure groups were evaluated for the number per group positive for MEAA, and a statistical analysis consisted of pair-wise t-tests for unequal variances was used to test for the differences in mean MEAA concentrations between the exposure groups. The number of samples detected as positive for MEAA exposure, that is, those above the test method's limit of detection (LOD = 0.1 μg/ml), were 92 (93.9%), 13 (34.2%), and 2 (3.3%) for the high, moderate, and low exposure workgroup categories, respectively. The mean urinary MEAA level was significantly greater in the high exposure category (6.8 μg/ml), compared to the moderate (0.42 μg/ml) and the low (0.07 μg/ml) exposure categories. The maximum concentration of urinary MEAA was 110 μg/ml for the high exposure category, while 4.8 μg/ml and 0.2 μg/ml maximum levels were found in the moderate and low exposure categories, respectively. This study demonstrated that urinary MEAA can be used as an accurate biomarker of exposure for JP-8 workers and clearly distinguished the differences in JP-8 exposure by workgroup category.

Ground-water quality, Cook Inlet Basin, Alaska, 1999

USGS Publications Warehouse

Glass, Roy L.

2001-01-01

As part of the U.S. Geological Survey?s National Water-Quality Assessment Program, ground-water samples were collected from 34 existing wells in the Cook Inlet Basin in south-central Alaska during 1999. All ground-water samples were from aquifers composed of glacial or alluvial sediments. The water samples were used to determine the occurrence and distribution of selected major ions, nutrients, trace elements, volatile organic compounds, pesticides, radioisotopes, and environmental isotopes. Of 34 samples, 29 were from wells chosen by using a grid-based random-selection process. Water samples from five major public-supply wells also were collected. Radon-222 and arsenic concentrations exceeded drinking-water standards proposed by the U.S. Environmental Protection Agency in 39 and 18 percent of sampled wells, respectively. The highest radon concentration measured during this study was 610 picocuries per liter; 12 of 31 samples exceeded the proposed maximum contaminant level of 300 picocuries per liter. The highest arsenic concentration was 29 micrograms per liter; 6 of 34 samples exceeded the proposed maximum contaminant level of 10 micrograms per liter. Human activities may be increasing the concen- tration of nitrate in ground water, but nitrate concentrations in all samples were less than the maximum contaminant level of 10 milligrams per liter as nitrogen. Concentrations of nitrate were highest in Anchorage and were as great as 4.8 milligrams per liter as nitrogen. Dissolved-solids concentrations ranged from 77 to 986 milligrams per liter; only 2 of 34 wells yielded water having greater than 500 milligrams per liter. Iron and manganese concentrations exceeded secondary maximum contaminant levels in 18 and 42 percent of samples, respectively. Concentrations of all pesticides and volatile organic compounds detected in ground-water samples were very low, less than 1 microgram per liter. No pesticide or volatile organic compounds were detected at concentrations exceeding drinking-water standards or guidelines. Water samples from one-half of the wells sampled had no detectable concentrations of pesticides or volatile organic carbons, at the parts-per-billion level. Concentrations of stable isotopes of hydrogen and oxygen in ground-water samples were similar to concentrations expected for modern precipitation and for water that has been affected by evaporation. Tritium activities and concentrations of chlorofluorocarbons indicated that the water samples collected from most wells were recharged less than 50 years ago.

Monitoring of Time-Dependent System Profiles by Multiplex Gas Chromatography with Maximum Entropy Demodulation

NASA Technical Reports Server (NTRS)

Becker, Joseph F.; Valentin, Jose

1996-01-01

The maximum entropy technique was successfully applied to the deconvolution of overlapped chromatographic peaks. An algorithm was written in which the chromatogram was represented as a vector of sample concentrations multiplied by a peak shape matrix. Simulation results demonstrated that there is a trade off between the detector noise and peak resolution in the sense that an increase of the noise level reduced the peak separation that could be recovered by the maximum entropy method. Real data originated from a sample storage column was also deconvoluted using maximum entropy. Deconvolution is useful in this type of system because the conservation of time dependent profiles depends on the band spreading processes in the chromatographic column, which might smooth out the finer details in the concentration profile. The method was also applied to the deconvolution of previously interpretted Pioneer Venus chromatograms. It was found in this case that the correct choice of peak shape function was critical to the sensitivity of maximum entropy in the reconstruction of these chromatograms.

Concentration dependence of biotransformation in fish liver S9: Optimizing substrate concentrations to estimate hepatic clearance for bioaccumulation assessment.

PubMed

Lo, Justin C; Allard, Gayatri N; Otton, S Victoria; Campbell, David A; Gobas, Frank A P C

2015-12-01

In vitro bioassays to estimate biotransformation rate constants of contaminants in fish are currently being investigated to improve bioaccumulation assessments of hydrophobic contaminants. The present study investigates the relationship between chemical substrate concentration and in vitro biotransformation rate of 4 environmental contaminants (9-methylanthracene, pyrene, chrysene, and benzo[a]pyrene) in rainbow trout (Oncorhynchus mykiss) liver S9 fractions and methods to determine maximum first-order biotransformation rate constants. Substrate depletion experiments using a series of initial substrate concentrations showed that in vitro biotransformation rates exhibit strong concentration dependence, consistent with a Michaelis-Menten kinetic model. The results indicate that depletion rate constants measured at initial substrate concentrations of 1 μM (a current convention) could underestimate the in vitro biotransformation potential and may cause bioconcentration factors to be overestimated if in vitro biotransformation rates are used to assess bioconcentration factors in fish. Depletion rate constants measured using thin-film sorbent dosing experiments were not statistically different from the maximum depletion rate constants derived using a series of solvent delivery-based depletion experiments for 3 of the 4 test chemicals. Multiple solvent delivery-based depletion experiments at a range of initial concentrations are recommended for determining the concentration dependence of in vitro biotransformation rates in fish liver fractions, whereas a single sorbent phase dosing experiment may be able to provide reasonable approximations of maximum depletion rates of very hydrophobic substances. © 2015 SETAC.

Explosion hazards of LPG-air mixtures in vented enclosure with obstacles.

PubMed

Zhang, Qi; Wang, Yaxing; Lian, Zhen

2017-07-15

Numerical simulations were performed to study explosion characteristics of liquefied petroleum gas (LPG) explosion in enclosure with a vent. Unlike explosion overpressure and dynamic pressure, explosion temperature of the LPG-air mixture at a given concentration in a vented enclosure has very little variation with obstacle numbers for a given blockage ratio. For an enclosure without obstacle, explosion overpressures for the stoichiometric mixtures and the fuel-lean mixtures reach their maximum within the vent and that for fuel-rich mixture reaches its maximum beyond and near the vent. Dynamic pressures produced by an indoor LPG explosion reach their maximum always beyond the vent no matter obstacles are present or not in the enclosure. A LPG explosion in a vented enclosure with built-in obstacles is strong enough to make the brick and mortar wall with a thickness of 370mm damaged. If there is no obstacle in the enclosure, the lower explosion pressure of several kPa can not break the brick and mortar wall with a thickness of 370mm. For a LPG explosion produced in an enclosure with a vent, main hazards, within the vent, are overpressure and high temperature. However main hazards are dynamic pressure, blast wind, and high temperature beyond the vent. Copyright © 2017 Elsevier B.V. All rights reserved.

Satellite derived smoke climatology for the United States and surface particulate pollution implications

NASA Astrophysics Data System (ADS)

Kaulfus, A. S.; Nair, U.; Jaffe, D. A.; Christopher, S. A.; Goodrick, S.

2017-12-01

Biomass burning smoke is a significant contributor to the degradation of air quality with well-documented impacts on the human respiratory system. Despite this, documentation of the distribution of smoke and assessing environmental impacts is largely limited to individual or seasonal events. This study presents a 12-year satellite based distribution of smoke across the Continental United States and describes seasonal and regional differences. The impact of smoke on surface fine particulate matter (PM2.5) concentrations is quantified by the enhancement in PM2.5 over "smoke free" conditions and the relative number of Environmental Protection Agency standard exceedances in the presence of smoke. Smoke occurrence frequency is at a maximum during the summer over the northern Great Plains region of the US and least frequent over the Southwest. Approximately 20% of exceedances of the 24-hour federal standard for particulate matters occur in the presences of smoke. Particulate impacts are at a maximum in the spring and summer in the southeast and northwest respectively corresponding to regional maximums in smoke occurrence. Air quality monitor specific climatological documentation of smoke and corresponding PM2.5 has relevance in EPA exceptional event data exclusion. Near real time evaluation of the dataset can aid in impact mitigation and regulation compliance.

Physical Limitations of Phosphor layer thickness and concentration for White LEDs.

PubMed

Tan, Cher Ming; Singh, Preetpal; Zhao, Wenyu; Kuo, Hao-Chung

2018-02-05

Increasing phosphor layer thickness and concentration can enhance the lumen flux of white LED (W-LED). In this work, we found that increasing the phosphor layer thickness and concentration can increase its temperature, and there is also a maximum thickness and concentration beyond which their increase will not lead to lumen increase, but only temperature increase. Higher thickness and higher concentration also results in warm light instead of White light. The maximum thickness and concentration are found to be limited by the scattering of light rays with higher % decrease of blue light rays than the yellow light rays. The results obtained in this work can also be used to compute the temperature and thermo-mechanical stress distribution of an encapsulated LED, demonstrating its usefulness to the design of encapsulated LED packages. Simulation software like ANSYS and TracePro are used extensively to verify the root cause mechanisms.

Biochemical and genotoxic response of naphthalene to fingerlings of milkfish Chanos chanos.

PubMed

Palanikumar, L; Kumaraguru, A K; Ramakritinan, C M

2013-09-01

The present study investigated the acute toxicity, sub-lethal toxicity and biochemical response of naphthalene in fingerlings of milkfish Chanos chanos. The 96 h acute toxicity LC50 values for C. chanos exposed to naphthalene was 5.18 μg l(-1). The estimated no observed effect concentration and lowest observed effect concentration values for naphthalene in C. chanos were 0.42 and 0.69 μg l(-1) respectively for 30 days. The estimated maximum allowable toxicant concentration for naphthalene was 0.53 μg l(-1). Biochemical enzyme markers such as lipid peroxidation, catalase, glutathione S transferase and reduced glutathione were measured in gills and liver tissues of C. chanos exposed to sub-lethal concentrations of naphthalene. Fluctuation in lipid peroxidation and catalase level suggests that naphthalene concentrations play a vital role in induction of oxidative stress in fish. Induction of reduced glutathione level and inhibition of glutathione S-transferase level was observed in naphthalene exposed C. chanos suggesting that there may be enhanced oxidative damage due to free radicals. Increasing concentration increases in number of nuclear abnormalities. The formation of micronuclei and binucleated micronuclei induction by naphthalene confirm its genotoxic potential. The highest levels of DNA damage (% tail length) were observed at 1.24 μg l(-1) of naphthalene. The study suggests that biochemical enzymes, nuclear abnormalities and DNA damage index can serve as a biological marker for naphthalene contamination.

[Studies on markers of exposure and early effect in areas with arsenic pollution: methods and results of the project SEpiAs. Epidemiological studies on population exposed to low-to-moderate arsenic concentration in drinking water].

PubMed

Bustaffa, Elisa; Bianchi, Fabrizio

2014-01-01

Arsenic and its inorganic compounds are classified as human carcinogens. Several epidemiological studies conducted in areas of the world characterized by high arsenic concentration in drinking water, even up to 3,000 μg/l, report associations between arsenic exposure and skin, bladder, lung, liver and kidney cancer as well as cardiovascular diseases, diabetes and reproductive and developmental effects. Since general population is not exposed to these high arsenic concentrations in the last years attention focused on adverse health effects that low-to-moderate arsenic concentrations (0-150 μg/l) in drinking water could induce. The World Health Organization recommends a maximum limit of 10 μg/l for arsenic in drinking water. Almost all epidemiological studies conducted on populations exposed to low-to-moderate arsenic concentrations in drinking water are limited due to problems arising from both individual exposure assessment and low subjects number. The aim of the present review is to collect literature-based evidences regarding adverse health effects associated with exposure to low-to-moderate arsenic concentrations in drinking water (10-150 μg/l) in order to obtain a comprehensive picture of the health outcomes that such exposure can have on general population.

Heavy metals and metalloid content in vegetables and soil collected from the gardens of Zagreb, Croatia.

PubMed

Puntarić, Dinko; Vidosavljević, Domagoj; Gvozdić, Vlatka; Puntarić, Eda; Puntarić, Ida; Mayer, Dijana; Bosnir, Jasna; Lasić, Dario; Jergović, Matijana; Klarić, Ivana; Vidosavljević, Marina; Krivdić, Ivancica

2013-09-01

Aim of this study was to determine concentration of Pb, Cd, As and Hg in green leafy vegetables and soil in the urban area of Zagreb, Croatia and to determine if there is a connection between the contamination of soil and vegetables. Green leafy vegetables and soil samples were taken from the gardens located in the outskirts of the city. Concentrations of Pb, Cd, As and Hg were determined by atomic absorption spectrometry; showing that average concentrations of metals and metalloids in vegetables and in soil, regardless of the location of sampling were below the maximum allowed concentration (MAC). The analysis determined that metal concentrations in only nine vegetable samples (9%) were above maximum allowed values prescribed by national and European legislation (three with higher concentrations of Pb, one with a higher concentration of Cd and five with higher concentrations of Hg). Concentrations of contaminants present in the analysed samples, in general, are lower than the ones published in similar studies. The final distribution and concentration of contaminants in vegetables of Zagreb, besides industry and traffic, is affected by the dominant wind direction.

Water-Quality Assessment of the Rio Grande Valley, Colorado, New Mexico, and Texas--Surface-Water Quality, Shallow Ground-Water Quality, and Factors Affecting Water Quality in the Rincon Valley, South-Central New Mexico, 1994-95

USGS Publications Warehouse

Anderholm, Scott K.

2002-01-01

As part of the National Water-Quality Assessment Program, surface-water and ground-water samples were collected in 1994 and 1995 for analysis of common constituents, nutrients, dissolved organic carbon, trace elements, radioactivity, volatile organic compounds, and pesticides to characterize surface- water quality and shallow ground-water quality and to determine factors affecting water quality in the Rincon Valley, south-central New Mexico. Samples of surface water were collected from three sites on the Rio Grande and from sites on three agricultural drains in the Rincon Valley in January 1994 and 1995, April 1994, and October 1994. Ground-water samples were collected in late April and early May 1994 from 30 shallow wells that were installed during the investigation. Dissolved-solids concentrations in surface water ranged from 434 to 1,510 milligrams per liter (mg/L). Dissolved-solids concentrations were smallest in water from the Rio Grande below Caballo Dam and largest in the drains. Nitrite plus nitrate concentrations ranged from less than 0.05 to 3.3 mg/L as nitrogen, and ammonia concentrations ranged from less than 0.015 to 0.33 mg/L as nitrogen in surface-water samples. Trace-element concentrations in surface water were significantly smaller than the acute-fisheries standards. One or more pesticides were detected in 34 of 37 surface-water samples. DCPA (dacthal) and metolachlor were the most commonly detected pesticides. No standards have been established for the pesticides analyzed for in this study. Dissolved-solids concentrations in shallow ground water ranged from 481 to 3,630 mg/L. All but 2 of 30 samples exceeded the secondary maximum contaminant level for dissolved solids of 500 mg/L. Water from about 73 percent of the wells sampled exceeded the secondary maximum contaminant level of 250 mg/L for sulfate, and water from about 7 percent of the wells sampled exceeded the secondary maximum contaminant level of 250 mg/L for chloride. Nitrite plus nitrate concentrations ranged from less than 0.05 to 33 mg/L as nitrogen in shallow ground water. Water from about 17 percent of the well samples exceeded the maximum contaminant level of 10 mg/L as nitrogen for nitrite plus nitrate. Trace-element concentrations in shallow ground water generally were small (1 to 10 micrograms per liter). The proposed maximum contaminant level of 20 micrograms per liter for uranium was exceeded in about 13 percent of the samples. The secondary maximum contaminant level of 300 micrograms per liter for iron was exceeded in about 17 percent of the samples and of 50 micrograms per liter for manganese was exceeded in about 83 percent of the samples. Samples from about 23 percent of the wells exceeded the maximum contaminant level of 15 picocuries per liter for gross alpha activity. One or more pesticides were detected in water from 12 of 30 wells sampled. The pesticides or pesticide metabolites diazinon, metolachlor, napropamide, p,p'-DDE, and prometon were detected in one or more samples. Metolachlor and prometon were the most commonly detected pesticides. Health advisories for the pesticides detected in shallow ground water (no maximum contaminant levels have been established for the pesticides detected) are 10 to 300 times larger than the concentrations detected. Infiltration, evaporation, and transpiration of irrigation water are important factors affecting the concentrations of common constituents in shallow ground water in the Rincon Valley. Dissolution and precipitation of minerals and mixing of shallow ground water and inflow of ground water from adjacent areas also affect the composition of shallow ground water and water in the drains. Relatively large nitrite plus nitrate concentrations in several shallow ground-water samples indicate leaching of fertilizers in some areas of th

Ground-water-quality assessment of the Central Oklahoma aquifer, Oklahoma; hydrologic, water-quality, and quality-assurance data 1987-90

USGS Publications Warehouse

Ferree, D.M.; Christenson, S.C.; Rea, A.H.; Mesander, B.A.

1992-01-01

This report presents data collected from 202 wells between June 1987 and September 1990 as part of the Central Oklahoma aquifer pilot study of the National Water-Quality Assessment Program. The report describes the sampling networks, the sampling procedures, and the results of the ground-water quality and quality-assurance sample analyses. The data tables consist of information about the wells sampled and the results of the chemical analyses of ground water and quality-assurance sampling. Chemical analyses of ground-water samples in four sampling networks are presented: A geochemical network, a low-density survey bedrock network, a low-density survey alluvium and terrace deposits network, and a targeted urban network. The analyses generally included physical properties, major ions, nutrients, trace substances, radionuclides, and organic constituents. The chemical analyses of the ground-water samples are presented in five tables: (1) Physical properties and concentrations of major ions, nutrients, and trace substances; (2) concentrations of radionuclides and radioactivities; (3) carbon isotope ratios and delta values (d-values) of selected isotopes; (4) concentrations of organic constituents; and (5) organic constituents not reported in ground-water samples. The quality of the ground water sampled varied substantially. The sum of constituents (dissolved solids) concentrations ranged from 71 to 5,610 milligrams per liter, with 38 percent of the wells sampled exceeding the Secondary Maximum Contaminant Level of 500 milligrams per liter established under the Safe Drinking Water Act. Values of pH ranged from 5.7 to 9.2 units with 20 percent of the wells outside the Secondary Maximum Contaminant Level of 6.5 to 8.5 units. Nitrite plus nitrate concentrations ranged from less than 0.1 to 85 milligrams per liter with 8 percent of the wells exceeding the proposed Maximum Contaminant Level of 10 milligrams per liter. Concentrations of trace substances were highly variable, ranging from below the reporting level to concentrations over the Maximum Contaminant Levels for several constituents (arsenic, barium, cadmium, chromium, lead, and selenium). Radionuclide activities also were highly variable. Gross alpha radioactivity ranged from 0.1 to 210 picocuries per liter as 230thorium. Of the wells sampled, 20 percent exceeded the proposed Maximum Contaminant Level of 15 picocuries per liter for gross alpha radioactivity. Organic constituents were detected in 39 percent of the 170 wells sampled for organic constituents; in most cases concentrations were at or near the laboratory minimum reporting levels. Ten of the wells sampled for organic constituents had one or more constituents (chlordane, dieldrin, heptachlor epoxide, trichloroethylene, 1,1-dichloroethylene, 1,1,1-trichloroethane) at concentrations equal to or greater than the Maximum Contaminant Level or acceptable concentrations as suggested in the Environmental Protection Agency's Health Advisory Summaries. Quality-assurance sampling included duplicate samples, repeated samples, blanks, spikes, and blind samples. These samples proved to be essential in evaluating the accuracy of the data, particularly in the case of volatile organic constituents.

Maximum thrust mode evaluation

NASA Technical Reports Server (NTRS)

Orme, John S.; Nobbs, Steven G.

1995-01-01

Measured reductions in acceleration times which resulted from the application of the F-15 performance seeking control (PSC) maximum thrust mode during the dual-engine test phase is presented as a function of power setting and flight condition. Data were collected at altitudes of 30,000 and 45,000 feet at military and maximum afterburning power settings. The time savings for the supersonic acceleration is less than at subsonic Mach numbers because of the increased modeling and control complexity. In addition, the propulsion system was designed to be optimized at the mid supersonic Mach number range. Recall that even though the engine is at maximum afterburner, PSC does not trim the afterburner for the maximum thrust mode. Subsonically at military power, time to accelerate from Mach 0.6 to 0.95 was cut by between 6 and 8 percent with a single engine application of PSC, and over 14 percent when both engines were optimized. At maximum afterburner, the level of thrust increases were similar in magnitude to the military power results, but because of higher thrust levels at maximum afterburner and higher aircraft drag at supersonic Mach numbers the percentage thrust increase and time to accelerate was less than for the supersonic accelerations. Savings in time to accelerate supersonically at maximum afterburner ranged from 4 to 7 percent. In general, the maximum thrust mode has performed well, demonstrating significant thrust increases at military and maximum afterburner power. Increases of up to 15 percent at typical combat-type flight conditions were identified. Thrust increases of this magnitude could be useful in a combat situation.

Differential effects of short- and long-term zolpidem treatment on recombinant α1β2γ2s subtype of GABAA receptors in vitro

PubMed Central

Vlainić, Josipa; Jembrek, Maja Jazvinšćak; Vlainić, Toni; Štrac, Dubravka Švob; Peričić, Danka

2012-01-01

Aim: Zolpidem is a non-benzodiazepine agonist at benzodiazepine binding site in GABAA receptors, which is increasingly prescribed. Recent studies suggest that prolonged zolpidem treatment induces tolerance. The aim of this study was to explore the adaptive changes in GABAA receptors following short and long-term exposure to zolpidem in vitro. Methods: Human embryonic kidney (HEK) 293 cells stably expressing recombinant α1β2γ2s GABAA receptors were exposed to zolpidem (1 and 10 μmol/L) for short-term (2 h daily for 1, 2, or 3 consecutive days) or long-term (continuously for 48 h). Radioligand binding studies were used to determine the parameters of [3H]flunitrazepam binding sites. Results: A single (2 h) or repeated (2 h daily for 2 or 3 d) short-term exposure to zolpidem affected neither the maximum number of [3H]flunitrazepam binding sites nor the affinity. In both control and short-term zolpidem treated groups, addition of GABA (1 nmol/L–1 mmol/L) enhanced [3H]flunitrazepam binding in a concentration-dependent manner. The maximum enhancement of [3H]flunitrazepam binding in short-term zolpidem treated group was not significantly different from that in the control group. In contrast, long-term exposure to zolpidem resulted in significantly increase in the maximum number of [3H]flunitrazepam binding sites without changing the affinity. Furthermore, long-term exposure to zolpidem significantly decreased the ability of GABA to stimulate [3H]flunitrazepam binding. Conclusion: The results suggest that continuous, but not intermittent and short-term, zolpidem-exposure is able to induce adaptive changes in GABAA receptors that could be related to the development of tolerance and dependence. PMID:22922343

Reynolds number effect on overall performance of a 10.8-centimeter (4.25-inch) sweptback bladed centrifugal compressor

NASA Technical Reports Server (NTRS)

Weigel, C.; Ball, C. L.

1972-01-01

The performance data were taken at 50,000 rpm, using argon gas. As the Reynolds number was reduced from near design value to 30 percent of design, the maximum efficiency decreased about 1.5 percentage points. Reducing the Reynolds number from 30 percent to approximately 10 percent of design caused the maximum efficiency to decrease another 2.5 percentage points. The variation in loss with Reynolds number is compared with inverse power relation of loss with Reynolds number.

Arsenic in ground water in selected parts of southwestern Ohio, 2002-03

USGS Publications Warehouse

Thomas, Mary Ann; Schumann, Thomas L.; Pletsch, Bruce A.

2005-01-01

Arsenic concentrations were measured in 57 domestic wells in Preble, Miami, and Shelby Counties, in southwestern Ohio. The median arsenic concentration was 7.1 ?g/L (micrograms per liter), and the maximum was 67.6 ?g/L. Thirty-seven percent of samples had arsenic concentrations greater than the U.S. Environmental Protection Agency drinking-water standard of 10 ?g/L. Elevated arsenic concentrations (>10 ?g/L) were detected over the entire range of depths sampled (42 to 221 feet) and in each of three aquifer types, Silurian carbonate bedrock, glacial buried-valley deposits, and glacial till with interbedded sand and gravel. One factor common in all samples with elevated arsenic concentrations was that iron concentrations were greater than 1,000 ?g/L. The observed correlations of arsenic with iron and alkalinity are consistent with the hypothesis that arsenic was released from iron oxides under reducing conditions (by reductive dissolution or reductive desorption). Comparisons among the three aquifer types revealed some differences in arsenic occurrence. For buried-valley deposits, the median arsenic concentration was 4.6 ?g/L, and the maximum was 67.6 ?g/L. There was no correlation between arsenic concentrations and depth; the highest concentrations were at intermediate depths (about 100 feet). Half of the buried-valley samples were estimated to be methanic. Most of the samples with elevated arsenic concentrations also had elevated concentrations of dissolved organic carbon and ammonia. For carbonate bedrock, the median arsenic concentration was 8.0 ?g/L, and the maximum was 30.7 ?g/L. Arsenic concentrations increased with depth. Elevated arsenic concentrations were detected in iron- or sulfate-reducing samples. Arsenic was significantly correled with molybdenum, strontium, fluoride, and silica, which are components of naturally ocurring minerals. For glacial till with interbedded sand and gravel, half of the samples had elevated arsenic concentrations. The median was 11.4 ?g/L, and the maximum was 27.6 ?g/L. At shallow depths (<100 feet), this aquifer type had higher arsenic and iron concentrations than carbonate bedrock. It is not known whether these observed differences among aquifer types are related to variations in (1) arsenic content of the aquifer material, (2) organic carbon content of the aquifer material, (3) mechanisms of arsenic mobilization (or uptake), or (4) rates of arsenic mobilization (or uptake). A followup study that includes solid-phase analyses and geochemical modeling was begun in 2004 in northwestern Preble County.

Residual toxicity of Cypermethrin in the larvae of coconut pest Oryctes rhinoceros (Coleoptera: Scarabaeidae).

PubMed

Venkatarajappa, P

2001-01-01

The toxic effect of Cypermethrin 10 EC (0.125, 0.25 and 0.5%) was estimated in the bodywall and digestive system of the larvae of Oryctes rhinoceros by HPLC after exposing them to different concentrations (0.125, 0.25 and 0.5%). Among the various concentrations used maximum residues were detected in bodywall (0.25%), whereas at higher concentration (0.5%) the residue detected was minimum. The treatment of Cypermethrin was found to be highly toxic upto 12 h of treatment, after which it declined reaching the minimum by 24 h. The residue of Cypermethrin could not be detected in digestive system. The experiments indicate the pesticide get concentrated in the bodywall to a maximum extent.

ARMA-Based SEM When the Number of Time Points T Exceeds the Number of Cases N: Raw Data Maximum Likelihood.

ERIC Educational Resources Information Center

Hamaker, Ellen L.; Dolan, Conor V.; Molenaar, Peter C. M.

2003-01-01

Demonstrated, through simulation, that stationary autoregressive moving average (ARMA) models may be fitted readily when T>N, using normal theory raw maximum likelihood structural equation modeling. Also provides some illustrations based on real data. (SLD)

The impact of meteorology on ozone in Houston

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eder, B.K.; Davis, J.M.; Nychka, D.

1997-12-31

This paper compares the results from both a one-stage hierarchical clustering technique (average linkage) and a two-stage technique (average linkage then k-means) as part of an objective meteorological Classification scheme designed to better elucidate ozone`s dependence on meteorology in the Houston, Texas, area. When applied to twelve years of meteorological data (1981-1992), each technique identified seven statistically distinct meteorological regimes, the majority of which exhibited significantly different daily 1-hour maximum ozone (O{sub 3}) concentrations. While both clustering approaches proved successful, the two-stage approach did appear superior in terms of better segregation of the mean O{sub 3}, concentrations. Both approaches indicatedmore » that the largest mean daily one-hour maximum concentrations are associated with migrating anticyclones and not with the quasi-permanent Bermuda High that often dominates the southeastern United States during the summer. As a result, maximum ozone concentrations are just as likely during the months of April, May, September and October as they are during the summer months. These findings support and help explain the unique O{sub 3}, climatology experienced by the Houston area.« less

The Impact of Reconstruction Methods, Phylogenetic Uncertainty and Branch Lengths on Inference of Chromosome Number Evolution in American Daisies (Melampodium, Asteraceae)

PubMed Central

McCann, Jamie; Stuessy, Tod F.; Villaseñor, Jose L.; Weiss-Schneeweiss, Hanna

2016-01-01

Chromosome number change (polyploidy and dysploidy) plays an important role in plant diversification and speciation. Investigating chromosome number evolution commonly entails ancestral state reconstruction performed within a phylogenetic framework, which is, however, prone to uncertainty, whose effects on evolutionary inferences are insufficiently understood. Using the chromosomally diverse plant genus Melampodium (Asteraceae) as model group, we assess the impact of reconstruction method (maximum parsimony, maximum likelihood, Bayesian methods), branch length model (phylograms versus chronograms) and phylogenetic uncertainty (topological and branch length uncertainty) on the inference of chromosome number evolution. We also address the suitability of the maximum clade credibility (MCC) tree as single representative topology for chromosome number reconstruction. Each of the listed factors causes considerable incongruence among chromosome number reconstructions. Discrepancies between inferences on the MCC tree from those made by integrating over a set of trees are moderate for ancestral chromosome numbers, but severe for the difference of chromosome gains and losses, a measure of the directionality of dysploidy. Therefore, reliance on single trees, such as the MCC tree, is strongly discouraged and model averaging, taking both phylogenetic and model uncertainty into account, is recommended. For studying chromosome number evolution, dedicated models implemented in the program ChromEvol and ordered maximum parsimony may be most appropriate. Chromosome number evolution in Melampodium follows a pattern of bidirectional dysploidy (starting from x = 11 to x = 9 and x = 14, respectively) with no prevailing direction. PMID:27611687

The Impact of Reconstruction Methods, Phylogenetic Uncertainty and Branch Lengths on Inference of Chromosome Number Evolution in American Daisies (Melampodium, Asteraceae).

PubMed

McCann, Jamie; Schneeweiss, Gerald M; Stuessy, Tod F; Villaseñor, Jose L; Weiss-Schneeweiss, Hanna

2016-01-01

Chromosome number change (polyploidy and dysploidy) plays an important role in plant diversification and speciation. Investigating chromosome number evolution commonly entails ancestral state reconstruction performed within a phylogenetic framework, which is, however, prone to uncertainty, whose effects on evolutionary inferences are insufficiently understood. Using the chromosomally diverse plant genus Melampodium (Asteraceae) as model group, we assess the impact of reconstruction method (maximum parsimony, maximum likelihood, Bayesian methods), branch length model (phylograms versus chronograms) and phylogenetic uncertainty (topological and branch length uncertainty) on the inference of chromosome number evolution. We also address the suitability of the maximum clade credibility (MCC) tree as single representative topology for chromosome number reconstruction. Each of the listed factors causes considerable incongruence among chromosome number reconstructions. Discrepancies between inferences on the MCC tree from those made by integrating over a set of trees are moderate for ancestral chromosome numbers, but severe for the difference of chromosome gains and losses, a measure of the directionality of dysploidy. Therefore, reliance on single trees, such as the MCC tree, is strongly discouraged and model averaging, taking both phylogenetic and model uncertainty into account, is recommended. For studying chromosome number evolution, dedicated models implemented in the program ChromEvol and ordered maximum parsimony may be most appropriate. Chromosome number evolution in Melampodium follows a pattern of bidirectional dysploidy (starting from x = 11 to x = 9 and x = 14, respectively) with no prevailing direction.

Extremes in Otolaryngology Resident Surgical Case Numbers: An Update.

PubMed

Baugh, Tiffany P; Franzese, Christine B

2017-06-01

Objectives The purpose of this study is to examine the effect of minimum case numbers on otolaryngology resident case log data and understand differences in minimum, mean, and maximum among certain procedures as a follow-up to a prior study. Study Design Cross-sectional survey using a national database. Setting Academic otolaryngology residency programs. Subjects and Methods Review of otolaryngology resident national data reports from the Accreditation Council for Graduate Medical Education (ACGME) resident case log system performed from 2004 to 2015. Minimum, mean, standard deviation, and maximum values for total number of supervisor and resident surgeon cases and for specific surgical procedures were compared. Results The mean total number of resident surgeon cases for residents graduating from 2011 to 2015 ranged from 1833.3 ± 484 in 2011 to 2072.3 ± 548 in 2014. The minimum total number of cases ranged from 826 in 2014 to 1004 in 2015. The maximum total number of cases increased from 3545 in 2011 to 4580 in 2015. Multiple key indicator procedures had less than the required minimum reported in 2015. Conclusion Despite the ACGME instituting required minimum numbers for key indicator procedures, residents have graduated without meeting these minimums. Furthermore, there continues to be large variations in the minimum, mean, and maximum numbers for many procedures. Variation among resident case numbers is likely multifactorial. Ensuring proper instruction on coding and case role as well as emphasizing frequent logging by residents will ensure programs have the most accurate data to evaluate their case volume.

Aerosol monitoring during carbon nanofiber production: mobile direct-reading sampling.

PubMed

Evans, Douglas E; Ku, Bon Ki; Birch, M Eileen; Dunn, Kevin H

2010-07-01

Detailed investigations were conducted at a facility that manufactures and processes carbon nanofibers (CNFs). Presented research summarizes the direct-reading monitoring aspects of the study. A mobile aerosol sampling platform, equipped with an aerosol instrument array, was used to characterize emissions at different locations within the facility. Particle number, respirable mass, active surface area, and photoelectric response were monitored with a condensation particle counter (CPC), a photometer, a diffusion charger, and a photoelectric aerosol sensor, respectively. CO and CO(2) were additionally monitored. Combined simultaneous monitoring of these metrics can be utilized to determine source and relative contribution of airborne particles (CNFs and others) within a workplace. Elevated particle number concentrations, up to 1.15 x 10(6) cm(-3), were found within the facility but were not due to CNFs. Ultrafine particle emissions, released during thermal treatment of CNFs, were primarily responsible. In contrast, transient increases in respirable particle mass concentration, with a maximum of 1.1 mg m(-3), were due to CNF release through uncontrolled transfer and bagging. Of the applied metrics, our findings suggest that particle mass was probably the most useful and practical metric for monitoring CNF emissions in this facility. Through chemical means, CNFs may be selectively distinguished from other workplace contaminants (Birch et al., in preparation), and for direct-reading monitoring applications, the photometer was found to provide a reasonable estimate of respirable CNF mass concentration. Particle size distribution measurements were conducted with an electrical low-pressure impactor and a fast particle size spectrometer. Results suggest that the dominant CNF mode by particle number lies between 200 and 250 nm for both aerodynamic and mobility equivalent diameters. Significant emissions of CO were also evident in this facility. Exposure control recommendations were described for processes as required.

Balloon borne measurements of aerosol and cloud particles over Japan during PACDEX

NASA Astrophysics Data System (ADS)

Sakai, T.; Orikasa, N.; Nagai, T.; Murakami, M.; Tajiri, T.; Saito, A.; Yamashita, K.

2007-12-01

This paper presents the preliminary result of the balloon borne measurements of the aerosol and cloud microphysical properties over Tsukuba (36.1°N, 140.1°E), Japan, on 10 and 22 May 2007. The purpose of the measurement is to study the influence of Asian mineral dust on ice clouds formation in the middle and upper troposphere. The balloon measured the vertical distributions of aerosol number size distribution (0.13 to 3.9 μm in threshold radius, 8 sizes) by use of the optical particle counter, cloud size (10 μ m to 5 mm in the longest dimension), shape, and number concentration by use of the hydrometer videosonde, humidity by use of SnowWhite hygrometer, and temperature and pressure by use of Meisei RS-01G radiosonde between altitudes of 0 and 16 km. The aerosol size distribution showed bimodal distribution with mode radii of <0.13 μm (fine mode) and about 0.8 μm (coarse mode) over the troposphere (0-13.5 km in altitude). The number concentrations ranged from 150 to 1 cm-3 in the fine mode and from 3 to 0.1 cm-3 in the coarse mode. High depolarization ratio (>10%) obtained from the ground-based Raman lidar measurement revealed the presence of nonspherical dust in the coarse mode. Columnar, bullet-like, and irregular ice crystals with 10-400 μm in size were detected between altitudes of 8 and 13 km on 10 May and 10 and 13 km on 22 May. The maximum crystal concentration was 0.15 cm-3. We discuss the possibility of the formation of the ice cloud from the dust based on the result of the measurements.

Aerosol Monitoring during Carbon Nanofiber Production: Mobile Direct-Reading Sampling

PubMed Central

Evans, Douglas E.; Ku, Bon Ki; Birch, M. Eileen; Dunn, Kevin H.

2010-01-01

Detailed investigations were conducted at a facility that manufactures and processes carbon nanofibers (CNFs). Presented research summarizes the direct-reading monitoring aspects of the study. A mobile aerosol sampling platform, equipped with an aerosol instrument array, was used to characterize emissions at different locations within the facility. Particle number, respirable mass, active surface area, and photoelectric response were monitored with a condensation particle counter (CPC), a photometer, a diffusion charger, and a photoelectric aerosol sensor, respectively. CO and CO2 were additionally monitored. Combined simultaneous monitoring of these metrics can be utilized to determine source and relative contribution of airborne particles (CNFs and others) within a workplace. Elevated particle number concentrations, up to 1.15 × 106 cm−3, were found within the facility but were not due to CNFs. Ultrafine particle emissions, released during thermal treatment of CNFs, were primarily responsible. In contrast, transient increases in respirable particle mass concentration, with a maximum of 1.1 mg m−3, were due to CNF release through uncontrolled transfer and bagging. Of the applied metrics, our findings suggest that particle mass was probably the most useful and practical metric for monitoring CNF emissions in this facility. Through chemical means, CNFs may be selectively distinguished from other workplace contaminants (Birch et al., in preparation), and for direct-reading monitoring applications, the photometer was found to provide a reasonable estimate of respirable CNF mass concentration. Particle size distribution measurements were conducted with an electrical low-pressure impactor and a fast particle size spectrometer. Results suggest that the dominant CNF mode by particle number lies between 200 and 250 nm for both aerodynamic and mobility equivalent diameters. Significant emissions of CO were also evident in this facility. Exposure control recommendations were described for processes as required. PMID:20447936

[The Diagnostics of Detonation Flow External Field Based on Multispectral Absorption Spectroscopy Technology].

PubMed

Lü, Xiao-jing; Li, Ning; Weng, Chun-sheng

2016-03-01

Compared with traditional sampling-based sensing method, absorption spectroscopy technology is well suitable for detonation flow diagnostics, since it can provide with us fast response, nonintrusive, sensitive solution for situ measurements of multiple flow-field parameters. The temperature and concentration test results are the average values along the laser path with traditional absorption spectroscopy technology, while the boundary of detonation flow external field is unknown and it changes all the time during the detonation engine works, traditional absorption spectroscopy technology is no longer suitable for detonation diagnostics. The trend of line strength with temperature varies with different absorption lines. By increasing the number of absorption lines in the test path, more information of the non-uniform flow field can be obtained. In this paper, based on multispectral absorption technology, the reconstructed model of detonation flow external field distribution was established according to the simulation results of space-time conservation element and solution element method, and a diagnostic method of detonation flow external field was given. The model deviation and calculation error of the least squares method adopted were studied by simulation, and the maximum concentration and temperature calculation error was 20.1% and 3.2%, respectively. Four absorption lines of H2O were chosen and detonation flow was scanned at the same time. The detonation external flow testing system was set up for the valveless gas-liquid continuous pulse detonation engine with the diameter of 80 mm. Through scanning H2O absorption lines with a high frequency of 10 kHz, the on-line detection of detonation external flow was realized by direct absorption method combined with time-division multiplexing technology, and the reconstruction of dynamic temperature distribution was realized as well for the first time, both verifying the feasibility of the test method. The test results show that both of the temperature and H2O concentration rose with the arrival of detonation wave. With the increase of the vertical distance between the detonation tube nozzle and the laser path, the time of temperature and concentration coming to the peak delayed, and the temperature variation trend tended to slow down. At 20 cm from detonation tube nozzle, the maximum temperature hit 1 329 K and the maximum H2O concentration of 0.19 occurred at 4 ms after ignition. The research can provide with us the support for expanding the detonation test field with absorption spectroscopy technology, and can also help to promote the detonation mechanism research and to enhance the level of detonation engine control technology.

Fluoride and health hazards: community perception in a fluorotic area of central Rajasthan (India): an arid environment.

PubMed

Hussain, J; Hussain, I; Sharma, K C

2010-03-01

India is among the 23 nations around the globe where health problems occur due to excess ingestion of fluoride (>1.5 mg/l) by drinking water. In Rajasthan, 18 out of 32 districts are fluorotic and 11 million of the populations are at risk. An exploratory qualitative survey was conducted to describe perception of the community regarding fluoride and related health problems in Central Rajasthan. A study on distribution and health hazards by fluoride contaminate in groundwater was performed in 1,030 villages of Bhilwara district of Central Rajasthan. One thousand thirty water samples were collected and analyzed for fluoride concentration. Fluoride concentration in these villages varies from 0.2 to 13.0 mg/l. Seven hundred fifty-six (73.4%) villages have fluoride concentration above 1.0 mg/l. Sixty (5.83%) villages have fluoride concentration above 5.0 mg/l with maximum numbers (24, 19.5%) from Shahpura tehsil. A detailed fluorosis study was carried out in 41 villages out of 60 villages having fluoride above 5.0 mg/l in the study age, sex, and occupation data were also collected. Four thousand, two hundred fifty-two individuals above 5 years age were examined for the evidence of dental fluorosis, while 1998 individuals above 21 years were examined for the evidence of skeletal fluorosis. The overall prevalence of dental and skeletal fluorosis was found to be 3,270/4,252 (76.9%) and 949/1,998 (47.5%), respectively. Maximum of 23.9% (1,016) individuals have mild grade of Dean's classification. Three hundred seventy-four (8.8%) individuals have severe type of dental fluorosis. The Dean's Community Fluorosis Index for the studied area in total is 1.62. Maximum CFI 3.0 was recorded from Surajpura of Banera Tehsil. Five hundred sixty-six (28.3%) individuals have Grade I type of skeletal fluorosis while only 0.6% (12) individuals have Grade III skeletal fluorosis. In conclusion, the prevalence and severity of fluorosis increased with increasing fluoride concentration. It was interesting to note that in some villages, the prevalence and severity of fluorosis were highest in subjects belonging to the economically poor community. Similarly, male laborers showed highest prevalence of fluorosis. Prevalence and severity of fluorosis were observed higher in subjects using tobacco, bettle nuts, and alcoholic drinks. In contrast, subjects using citrus fruits and having good nutritional status showed low prevalence.

Emissions of indoor air pollutants from six user scenarios in a model room

NASA Astrophysics Data System (ADS)

Höllbacher, Eva; Ters, Thomas; Rieder-Gradinger, Cornelia; Srebotnik, Ewald

2017-02-01

In this study six common user scenarios putatively influencing indoor air quality were performed in a model room constructed according to the specifications of the European Reference Room given in the new horizontal prestandard prEN 16516 to gain further information about the influence of user activities on indoor air quality. These scenarios included the use of cleaning agent, an electric air freshener, an ethanol fireplace and cosmetics as well as cigarette smoking and peeling of oranges. Four common indoor air pollutants were monitored: volatile organic compounds (VOC), particulate matter (PM), carbonyl compounds and CO2. The development of all pollutants was determined during and after the test performance. For each measured pollutant, well-defined maximum values could be assigned to one or more of the individual user scenarios. The highest VOC concentration was measured during orange-peeling reaching a maximum value of 3547 μg m-3. Carbonyl compounds and PM were strongly elevated while cigarette smoking. Here, a maximum formaldehyde concentration of 76 μg m-3 and PM concentration of 378 μg m-3 were measured. CO2 was only slightly affected by most of the tests except the use of the ethanol fireplace where a maximum concentration of 1612 ppm was reached. Generally, the user scenarios resulted in a distinct increase of several indoor pollutants that usually decreased rapidly after the removal of the source.

Maximum-biomass prediction of homofermentative Lactobacillus.

PubMed

Cui, Shumao; Zhao, Jianxin; Liu, Xiaoming; Chen, Yong Q; Zhang, Hao; Chen, Wei

2016-07-01

Fed-batch and pH-controlled cultures have been widely used for industrial production of probiotics. The aim of this study was to systematically investigate the relationship between the maximum biomass of different homofermentative Lactobacillus and lactate accumulation, and to develop a prediction equation for the maximum biomass concentration in such cultures. The accumulation of the end products and the depletion of nutrients by various strains were evaluated. In addition, the minimum inhibitory concentrations (MICs) of acid anions for various strains at pH 7.0 were examined. The lactate concentration at the point of complete inhibition was not significantly different from the MIC of lactate for all of the strains, although the inhibition mechanism of lactate and acetate on Lactobacillus rhamnosus was different from the other strains which were inhibited by the osmotic pressure caused by acid anions at pH 7.0. When the lactate concentration accumulated to the MIC, the strains stopped growing. The maximum biomass was closely related to the biomass yield per unit of lactate produced (YX/P) and the MIC (C) of lactate for different homofermentative Lactobacillus. Based on the experimental data obtained using different homofermentative Lactobacillus, a prediction equation was established as follows: Xmax - X0 = (0.59 ± 0.02)·YX/P·C. Copyright © 2016. Published by Elsevier B.V.

To study the effect of orbital sling on post operative vision in cases of maxillary carcinoma undergoing total maxillectomy.

PubMed

Shukla, Anirudh; Dudeja, Vivek

2014-06-01

To study effect of orbital sling on post operative vision in cases of maxillary carcinoma undergoing total maxillectomy. All patients with the principal procedure of "total maxillectomy" for histopathologically proven cases of carcinoma maxilla in department of otorhinolaryngology and head-neck surgery, N.S.C.B. medical college, Jabalapur, Madhya Pradesh, India from July 2011 to October 2013 were included. Out of the 20 patients irrespective of whether orbital sling was created or not, maximum number of patients 8 (40 %) showed a 3 step improvement, and maximum improvement seen was up to five steps. Out of the 14 patients in which orbital sling was created maximum number of patients 7 (50 %) showed a 3 step improvement, and maximum improvement seen was up to five steps. Out of the 6 patients in whom orbital sling was not created maximum number of patients 3 (50 %) showed a 2 step improvement, and maximum improvement seen was up to three steps. Infraorbital repair with the help of sling results in better improvement of vision as compared to those in whom sling was not or could not be made with no significant difference on eye movements.

40 CFR 204.55-3 - Configuration identification.

Code of Federal Regulations, 2011 CFR

2011-07-01

... compressor stages. (3) Maximum pressure (psi). (4) Air intake system of compressor: (i) Number of filters; (ii) Type of filters. (5) The engine system: (i) Number of cylinders and configuration (L-6, V-8, V-12..., water cooled. (7) Fan: (i) Diameter; (ii) Maximum fan rpm. (8) The compressor enclosure: (i) Height...

40 CFR 204.55-3 - Configuration identification.

Code of Federal Regulations, 2013 CFR

2013-07-01

... compressor stages. (3) Maximum pressure (psi). (4) Air intake system of compressor: (i) Number of filters; (ii) Type of filters. (5) The engine system: (i) Number of cylinders and configuration (L-6, V-8, V-12..., water cooled. (7) Fan: (i) Diameter; (ii) Maximum fan rpm. (8) The compressor enclosure: (i) Height...

40 CFR 204.55-3 - Configuration identification.

Code of Federal Regulations, 2014 CFR

2014-07-01

... compressor stages. (3) Maximum pressure (psi). (4) Air intake system of compressor: (i) Number of filters; (ii) Type of filters. (5) The engine system: (i) Number of cylinders and configuration (L-6, V-8, V-12..., water cooled. (7) Fan: (i) Diameter; (ii) Maximum fan rpm. (8) The compressor enclosure: (i) Height...

40 CFR 204.55-3 - Configuration identification.

Code of Federal Regulations, 2012 CFR

2012-07-01

... compressor stages. (3) Maximum pressure (psi). (4) Air intake system of compressor: (i) Number of filters; (ii) Type of filters. (5) The engine system: (i) Number of cylinders and configuration (L-6, V-8, V-12..., water cooled. (7) Fan: (i) Diameter; (ii) Maximum fan rpm. (8) The compressor enclosure: (i) Height...

Pharmacology of 13-cis-retinoic acid in humans.

PubMed

Kerr, I G; Lippman, M E; Jenkins, J; Myers, C E

1982-05-01

Vitamin A and its analogs (retinoids) have shown great promise for the chemoprevention of cancer as well as being a possible new class of chemotherapeutic agents. A Phase I and II trial of 13-cis-retinoic acid in advanced cancers was initiated, and the clinical pharmacology of the drug was studied. All patients received p.o. 13-cis-retinoic acid starting at 0.5 mg/kg/day, escalating over 4 weeks to a maximum dose of 8 mg/kg/day in divided doses. Although there was a linear correlation of plasma concentration with dose escalation, large inter-individual variations in peak plasma concentrations were noted. At the maximum drug dose, the mean peak plasma concentration was 4 X 10(-6) M. There was little drug accumulation on this schedule, as trough concentrations between p.o. doses often dropped below 1 X 10(-6) M. The drug was metabolized extensively to a metabolite, the concentrations of which exceeding parent 13-cis-retinoic acid concentrations with chronic dosing. Retinol concentrations were below the normal range.

Formation mechanism of human serum albumin monolayers on positively charged polymer microparticles.

PubMed

Nattich-Rak, Małgorzata; Sadowska, Marta; Adamczyk, Zbigniew; Cieśla, Michał; Kąkol, Małgorzata

2017-11-01

Human serum albumin (HSA) adsorption on positively and negatively charged polystyrene microparticles was studied at various pHs and NaCl concentrations. Thorough electrophoretic mobility measurements were carried out that enabled to monitor in situ the progress of protein adsorption. The maximum coverage of irreversibly adsorbed HSA on microparticles was determined by different concentration depletion methods, one of them involving AFM imaging of residual molecules. An anomalous adsorption of HSA on the positive microparticles was observed at pH 3.5 where the maximum coverage attained 1.0mgm -2 for NaCl concentrations of 0.05M despite that the molecules were on average positively charged. For comparison, the maximum coverage of HSA on negatively charged microparticles was equal to 1.3mgm -2 at this pH and NaCl concentration. At pH 7.4 the maximum coverage on positive microparticles was equal to 2.1mgm -2 for 0.05M NaCl concentration. On the other hand, for negative microparticles, negligible adsorption of HSA was observed at pH 7.4 and 9.7. These experimental data were adequately interpreted in terms of the random sequential adsorption approach exploiting the bead model of the HSA molecule. Different orientations of adsorbed molecules, inert alia, the edge-on orientation prevailing for positively charged microparticles at pH 7.4, were confirmed. This was explained in terms of a heterogeneous charge distribution over the HSA molecule prevailing for a wide range of pHs. Copyright © 2017 Elsevier B.V. All rights reserved.

In vitro investigation of the effects of exogenous sugammadex on coagulation in orthopedic surgical patients.

PubMed

Lee, Il Ok; Kim, Young Sung; Chang, Hae Wone; Kim, Heezoo; Lim, Byung Gun; Lee, Mido

2018-05-24

Previous studies have shown that sugammadex resulted in the prolongation of prothrombin time and activated partial thromboplastin time. In this study, we aimed to investigate the in vitro effects of exogenous sugammadex on the coagulation variables of whole blood in healthy patients who underwent orthopedic surgery. The effects of sugammadex on coagulations were assessed using thromboelastography (TEG) in kaolin-activated citrated blood samples taken from 14 healthy patients who underwent orthopedic surgery. The in vitro effects of three different concentrations of sugammadex (42, 193, and 301 μg mL - 1 ) on the TEG profiles were compared with those of the control (0 μg mL - 1 ). Previous studies indicated that these exogenous concentrations correspond to the approximate maximum plasma concentrations achieved after the administration of 4, 16, and 32 mg kg - 1 sugammadex to healthy subjects. Increased sugammadex concentrations were significantly associated with reduced coagulation, as evidenced by increases in reaction time (r), coagulation time, and time to maximum rate of thrombus generation (TMRTG), and decreases in the angle, maximum amplitude, and maximum rate of thrombus generation. Compared with the control, the median percentage change (interquartile range) in the TEG values of the samples treated with the highest exogenous sugammadex concentration was the greatest for r, 53% (26, 67.3%), and TMRTG, 48% (26, 59%). This in vitro study suggests that supratherapeutic doses of exogenous sugammadex might be associated with moderate hypocoagulation in the whole blood of healthy subjects. identifier:  UMIN000029081 , registered 11 September 2017.

Multi-model study of mercury dispersion in the atmosphere: atmospheric processes and model evaluation

NASA Astrophysics Data System (ADS)

Travnikov, Oleg; Angot, Hélène; Artaxo, Paulo; Bencardino, Mariantonia; Bieser, Johannes; D'Amore, Francesco; Dastoor, Ashu; De Simone, Francesco; Diéguez, María del Carmen; Dommergue, Aurélien; Ebinghaus, Ralf; Feng, Xin Bin; Gencarelli, Christian N.; Hedgecock, Ian M.; Magand, Olivier; Martin, Lynwill; Matthias, Volker; Mashyanov, Nikolay; Pirrone, Nicola; Ramachandran, Ramesh; Read, Katie Alana; Ryjkov, Andrei; Selin, Noelle E.; Sena, Fabrizio; Song, Shaojie; Sprovieri, Francesca; Wip, Dennis; Wängberg, Ingvar; Yang, Xin

2017-04-01

Current understanding of mercury (Hg) behavior in the atmosphere contains significant gaps. Some key characteristics of Hg processes, including anthropogenic and geogenic emissions, atmospheric chemistry, and air-surface exchange, are still poorly known. This study provides a complex analysis of processes governing Hg fate in the atmosphere involving both measured data from ground-based sites and simulation results from chemical transport models. A variety of long-term measurements of gaseous elemental Hg (GEM) and reactive Hg (RM) concentration as well as Hg wet deposition flux have been compiled from different global and regional monitoring networks. Four contemporary global-scale transport models for Hg were used, both in their state-of-the-art configurations and for a number of numerical experiments to evaluate particular processes. Results of the model simulations were evaluated against measurements. As follows from the analysis, the interhemispheric GEM gradient is largely formed by the prevailing spatial distribution of anthropogenic emissions in the Northern Hemisphere. The contributions of natural and secondary emissions enhance the south-to-north gradient, but their effect is less significant. Atmospheric chemistry has a limited effect on the spatial distribution and temporal variation of GEM concentration in surface air. In contrast, RM air concentration and wet deposition are largely defined by oxidation chemistry. The Br oxidation mechanism can reproduce successfully the observed seasonal variation of the RM / GEM ratio in the near-surface layer, but it predicts a wet deposition maximum in spring instead of in summer as observed at monitoring sites in North America and Europe. Model runs with OH chemistry correctly simulate both the periods of maximum and minimum values and the amplitude of observed seasonal variation but shift the maximum RM / GEM ratios from spring to summer. O3 chemistry does not predict significant seasonal variation of Hg oxidation. Hence, the performance of the Hg oxidation mechanisms under study differs in the extent to which they can reproduce the various observed parameters. This variation implies possibility of more complex chemistry and multiple Hg oxidation pathways occurring concurrently in various parts of the atmosphere.

Chloride in Groundwater and Surface Water in Areas Underlain by the Glacial Aquifer System, Northern United States

USGS Publications Warehouse

Mullaney, John R.; Lorenz, David L.; Arntson, Alan D.

2009-01-01

A study of chloride in groundwater and surface water was conducted for the glacial aquifer system of the northern United States in forested, agricultural, and urban areas by analyzing data collected for the National Water-Quality Assessment Program from 1991 to 2004. Groundwater-quality data from a sampling of 1,329 wells in 19 states were analyzed. Chloride concentrations were greater than the secondary maximum contaminant level established by the U.S. Environmental Protection Agency of 250 milligrams per liter in 2.5 percent of samples from 797 shallow monitoring wells and in 1.7 percent of samples from 532 drinking-water supply wells. Water samples from shallow monitoring wells in urban areas had the largest concentration of chloride, followed by water samples from agricultural and forested areas (medians of 46, 12, and 2.9 milligrams per liter, respectively). An analysis of chloride:bromide ratios, by mass, and chloride concentrations compared to binary mixing curves for dilute groundwater, halite, sewage and animal waste, potassium chloride fertilizer, basin brines, seawater, and landfill leachate in samples from monitoring wells indicated multiple sources of chloride in samples from wells in urban areas and agricultural areas. Water from shallow monitoring wells in urban areas had the largest chloride:bromide ratio, and samples with chloride:bromide ratios greater than 1,000 and chloride concentrations greater than 100 milligrams per liter were dominated by halite; however, the samples commonly contained mixtures that indicated input from sewage or animal waste. Chloride:bromide ratios were significantly larger in samples from public-supply drinking-water wells than from private drinking-water wells, and ratios were significantly larger in all drinking-water wells in eastern and central regions of the glacial aquifer system than in west-central and western regions of the glacial aquifer system. Surface-water-quality data collected regularly during varying time periods from 1991-2004 from 100 basins dominated by forested, agricultural, or urban land in 15 states were analyzed to determine maximum measured chloride concentrations. Samples from 15 sites in east, central, and west-central areas, collected primarily in winter, had chloride concentrations higher than the U.S. Environmental Protection Agency recommended chronic criterion concentration for aquatic life of 230 milligrams per liter. Concentrations of chloride in base-flow samples were predictive of maximum measured chloride concentrations, indicating that inputs of chloride from groundwater and (or) point-source wastewater discharges increase the likelihood of samples exceeding the recommended chronic aquatic criterion. Multiple linear regression analyses showed that the density of major roads, potential evapotranspiration, and the percentage of annual runoff from saturated overland flow were significant factors in describing the range of maximum measured chloride concentrations in the basins studied. Chloride loads and yields were determined at 95 surface-water-monitoring stations in basins dominated by forested, agricultural, or urban land. Annual chloride yield was largest in the urban basins (median of 88 tons per square mile) and smallest in the forested basins (median of 6.4 tons per square mile). The median chloride yield in the agricultural basins was 15.4 tons per square mile. Multiple linear regression analyses showed that the density of highways (roads in U.S. highway system), the number of major wastewater discharges in the basin, potential evapotranspiration, and urban minus agricultural land area were significant factors in describing the range of average annual chloride yields. Upward trends in chloride loads were apparent in several urban basins for which additional long-term data were available. Increases in chloride loads over time may be related to a variety of factors, including increases in road area and consequent deicing, incr

Use of the Maximum Cumulative Ratio As an Approach for Prioritizing Aquatic Coexposure to Plant Protection Products: A Case Study of a Large Surface Water Monitoring Database.

PubMed

Vallotton, Nathalie; Price, Paul S

2016-05-17

This paper uses the maximum cumulative ratio (MCR) as part of a tiered approach to evaluate and prioritize the risk of acute ecological effects from combined exposures to the plant protection products (PPPs) measured in 3 099 surface water samples taken from across the United States. Assessments of the reported mixtures performed on a substance-by-substance approach and using a Tier One cumulative assessment based on the lowest acute ecotoxicity benchmark gave the same findings for 92.3% of the mixtures. These mixtures either did not indicate a potential risk for acute effects or included one or more individual PPPs that had concentrations in excess of their benchmarks. A Tier Two assessment using a trophic level approach was applied to evaluate the remaining 7.7% of the mixtures. This assessment reduced the number of mixtures of concern by eliminating the combination of endpoint from multiple trophic levels, identified invertebrates and nonvascular plants as the most susceptible nontarget organisms, and indicated that a only a very limited number of PPPs drove the potential concerns. The combination of the measures of cumulative risk and the MCR enabled the identification of a small subset of mixtures where a potential risk would be missed in substance-by-substance assessments.

The mechanical behaviour of NBR/FEF under compressive cyclic stress strain

NASA Astrophysics Data System (ADS)

Mahmoud, W. E.; El-Eraki, M. H. I.; El-Lawindy, A. M. Y.; Hassan, H. H.

2006-06-01

Acrylonitrile butadiene rubber compounds filled with different concentrations of fast extrusion furnace (FEF) carbon black were experimentally investigated. The stress-strain curves of the composites were studied, which suggest good filler-matrix adhesion. The large reinforcement effect of the filler followed the Guth model for non-spherical particles. The effect of FEF carbon black on the cyclic fatigue and hysteresis was also examined. The loading and unloading stress-strain relationships for any cycle were described by applying Ogden's model for rubber samples. The dissipation energy that indicates the vibration damping capacity for all samples was determined. A simple model was proposed, to investigate the relation between maximum stress and the number of cyclic fatigue.

Biodegradation of propargite by Pseudomonas putida, isolated from tea rhizosphere.

PubMed

Sarkar, Soumik; Seenivasan, Subbiah; Asir, Robert Premkumar Samuel

2010-02-15

Biodegradation of miticide propargite was carried out in vitro by selected Pseudomonas strains isolated from tea rhizosphere. A total number of 13 strains were isolated and further screened based on their tolerance level to different concentrations of propargite. Five best strains were selected and further tested for their nutritional requirements. Among the different carbon sources tested glucose exhibited the highest growth promoting capacity and among nitrogen sources ammonium nitrate supported the growth to the maximum. The five selected Pseudomonas strain exhibited a range of degradation capabilities. Mineral salts medium (MSM) amended with glucose provided better environment for degradation with the highest degradation potential in strain SPR 13 followed by SPR 8 (71.9% and 69.0% respectively).

Investigating radial wire array Z pinches as a compact x-ray source on the Saturn generator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ampleford, David J.; Bland, S. N.; Jennings, Christopher A.

2015-08-27

Radial wire array z pinches, where wires are positioned radially outward from a central cathode to a concentric anode, can act as a compact bright x-ray source that could potentially be used to drive a hohlraum. Experiments were performed on the 7-MA Saturn generator using radial wire arrays. These experiments studied a number of potential risks in scaling radial wire arrays up from the 1-MA level, where they have been shown to be a promising compact X-ray source. Data indicates that at 7 MA, radial wire arrays can radiate ~9 TW with 10-ns full-width at half-maximum from a compact pinch.

Mountain wetlands: efficient uranium filters - potential impacts

USGS Publications Warehouse

Owen, D.E.; Otton, J.K.

1995-01-01

Sediments in 67 of 145 Colorado wetlands sampled by the US Geological Survey contain moderate (20 ppm) or greater concentrations of uranium (some as high as 3000 ppm) based on dry weight. The proposed maximum contaminant level (MCL) for uranium in drinking water is 20 ??g/l or 20 ppb. By comparison, sediments in many of these wetlands contain 3 to 5 orders of magnitude more uranium than the proposed MCL. Wetlands near the workings of old mines may be trapping any number of additional metals/elements including Cu, Pb, Zn, As and Ag. Anthropogenic disturbances and natural changes may release uranium and other loosely bound metals presently contained in wetland sediments. -from Authors

Variation of rock-forming metals in sub-annual increments of modern Greenland snow

USGS Publications Warehouse

Hinkley, T.K.

1992-01-01

Modern snowpack from central south Greenland was sampled in sub-seasonal increments and analysed for a suite of major, minor and trace rock-forming metals (K, Rb, Cs, Ca, Sr, Ba). There is a sharp seasonal concentration maximum for all six metals that comes in summer, later than mid-June. Metal concentrations in all other parts of the year's snowpack are up to 10 or more times smaller. The concentration maximum is preceded by low values in autumn-winter, very low values in early-mid-spring, and moderate-to-high values in late spring early summer; this pattern is seen consistently in three separate time stratigraphic intervals representing the same seasonal periods, spanning the time interval 1981-1984. The absolute concentration values of the snow strata representing the low-concentration portion of the year, autumn-winter-spring, may vary substantially from year to year, by a factor of two, or more. The finding that all rock-forming metals are at a sharp concentration maximum in late summer contrasts with the interpretations of several other studies in high-latitude northern regions. Those studies have reported a broad maximum of continental dust-associated metals in late winter and spring. However samples of the other studies have mostly come from regions farther to the north, and the analyses have emphasized industrial pollutant metals rather than the matched rock-forming suite of the present study. The metals measured were chosen to give information about the origin and identity of the rock and soil dusts, and sea salts, present as impurities in the snow. Metal ratios indicate that the dusts in the snowpacks are of continental origin and from ferromagnesian rocks. Source rock types for dusts in central south Greenland snow contrast with the felsic rock dusts of the Sierra Nevada, CA, annual snowpacks, and with the very felsic rock dusts in large south central Alaskan mountain glaciers. Samples in which masses of sea salt are much larger than those of rock dusts may be identified by small changes in metal ratios caused by moderate increases of K and Ca from marine sources, nearly unaccompanied by the minor and trace metals Rb, Cs and Ba, that are very rare in the oceans. A sampling frequency, such as that of the present study, that divides a year's accumulation into 8-10 subsamples is sufficient to reveal details of the time pattern of variation in proportions and concentrations of metals that give information about atmospheric deposition of important types of earth materials.Modern snowpack from central south Greenland was sampled in sub-seasonal increments and analyzed for a suite of major, minor and trace rock-forming metals (K, Rb, Cs, Ca, Sr, Ba). There is a sharp seasonal concentration maximum for all six metals that comes in summer, later than mid-June. Metal concentrations in all other parts of the year's snowpack are up to 10 or more times smaller. The concentration maximum is preceded by low values in autumn-winter, very low values in early-mid-spring, and moderate-to-high values in late spring-early summer; this pattern is seen consistently in three separate time stratigraphic intervals representing the same seasonal periods, spanning the time interval 1981-1984. The absolute concentration values of the snow strata representing the low-concentration portion of the year, autumn-winter-spring, may vary substantially from year to year, by a factor of two, or more. The finding that all rock-forming metals are at a sharp concentration maximum in late summer contrasts with the interpretations of several other studies in high-latitude northern regions. Those studies have reported a broad maximum of continental dust-associated metals in late winter and spring. However, samples of the other studies have mostly come from regions farther to the north, and the analyses have emphasized industrial pollutant metals rather than the matched rock-forming suite of the present study. The metals measured were chosen to give informati

Induction of cyclo-oxygenase-2 mRNA by prostaglandin E2 in human prostatic carcinoma cells

NASA Technical Reports Server (NTRS)

Tjandrawinata, R. R.; Dahiya, R.; Hughes-Fulford, M.

1997-01-01

Prostaglandins are synthesized from arachidonic acid by the enzyme cyclo-oxygenase. There are two isoforms of cyclooxygenases: COX-1 (a constitutive form) and COX-2 (an inducible form). COX-2 has recently been categorized as an immediate-early gene and is associated with cellular growth and differentiation. The purpose of this study was to investigate the effects of exogenous dimethylprostaglandin E2 (dmPGE2) on prostate cancer cell growth. Results of these experiments demonstrate that administration of dmPGE2 to growing PC-3 cells significantly increased cellular proliferation (as measured by the cell number), total DNA content and endogenous PGE2 concentration. DmPGE2 also increased the steady-state mRNA levels of its own inducible synthesizing enzyme, COX-2, as well as cellular growth to levels similar to those seen with fetal calf serum and phorbol ester. The same results were observed in other human cancer cell types, such as the androgen-dependent LNCaP cells, breast cancer MDA-MB-134 cells and human colorectal carcinoma DiFi cells. In PC-3 cells, the dmPGE2 regulation of the COX-2 mRNA levels was both time dependent, with maximum stimulation seen 2 h after addition, and dose dependent on dmPGE2 concentration, with maximum stimulation seen at 5 microg ml(-1). The non-steroidal anti-inflammatory drug flurbiprofen (5 microM), in the presence of exogenous dmPGE2, inhibited the up-regulation of COX-2 mRNA and PC-3 cell growth. Taken together, these data suggest that PGE2 has a specific role in the maintenance of human cancer cell growth and that the activation of COX-2 expression depends primarily upon newly synthesized PGE2, perhaps resulting from changes in local cellular PGE2 concentrations.

Extraction of squalene from shark liver oil in a packed column using supercritical carbon dioxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Catchpole, O.J.; Kamp, J.C. von; Grey, J.B.

1997-10-01

Continuous extraction of squalene from shark liver oil using supercritical carbon dioxide was carried out in both laboratory and pilot scale plant. The shark liver oil contained around 50% by weight squalene, which was recovered as the main extract stream. The other major components in the oil were triglycerides, which were recovered as raffinate, and pristane, which was recovered as a second extract stream. Separation performance was determined as a function of temperature; pressure; oil to carbon dioxide flow rate ratio, packed height and type of packing; and reflux ratio. The pressure, temperature, and feed oil concentration of squalene determinedmore » the maximum loading of oil in carbon dioxide. The oil to carbon dioxide ratio determined the squalene concentration in both the product stream and raffinate stream. The ratio of oil flow rate to the flow rate of squalene required to just saturate carbon dioxide was found to be a useful correlating parameter for the oil loadings and product compositions. Of the three packings investigated, wire wool gave the best separation efficiency and Raschig rings the worst efficiency. Mass transfer correlations from the literature were used to estimate the number of transfer units (NTU) from experimental data and literature correlations. NTU`s from the experimental data were comparable to predictions at a pilot scale but were underpredicted at the laboratory scale. The use of reflux at the pilot scale enabled the concentration of squalene in the product stream to be increased from 92% by mass to a maximum of 99% by mass at fractionation conditions of 250 bar and 333 K.« less

Gaussian plume atmospheric modelling and radiation exposure calculations following the cremation of a deceased thyroid cancer patient treated with iodine-131.

PubMed

Calais, Phillipe J

2017-03-20

Shortly after treatment with 7200 MBq of 131 I, a thyroid cancer patient died and was subsequently cremated. Calculations of the atmospheric emissions of 131 I from the crematorium flue were performed using a standard atmospheric pollution Gaussian Plume Dispersal model. Estimates of whole-body and thyroid dose of those potentially exposed were made using OLINDA/EXM dosimetry software. Under the meteorological conditions prevalent at the time of the cremation, and depending on the actual release rate of the 131 I, the Western Australian legal limit of 3.7 Bqm -3 for atmospheric emissions of 131 I may have been exceeded for distances of up to 440 and 1610 m downwind of the crematorium chimney, with the maximum concentration being between 33 and 392 Bqm -3 . Assuming 16% of the inhaled 131 I was taken up in the thyroid with the balance in the remainder of the body, the radiation dose to maximally exposed individuals was calculated to be approximately 17.7 μSv to the thyroid and 0.04 μSv to the whole-body. Despite the maximum allowable atmospheric 131 I concentration of 3.7 Bqm -3 being exceeded, as the number of people immediately downwind of the crematorium flue in the high concentration zones was very low, and considering the relatively high tolerable dose to the thyroid, the radiation dose to people was probably not a problem in this case. The local limit of 1000 MBq of 131 I for the cremation of a deceased patient is reasonable, but with adequate precautions could be significantly increased without any harmful effects to people or the environment.

Complete and simultaneous removal of ammonium and m-cresol in a nitrifying sequencing batch reactor.

PubMed

Zepeda, Alejandro; Ben-Youssef, Chérif; Rincón, Susana; Cuervo-López, Flor; Gómez, Jorge

2013-06-01

The kinetic behavior, oxidizing ability and tolerance to m-cresol of a nitrifying sludge exposed to different initial concentrations of m-cresol (0-150 mg C L(-1)) were evaluated in a sequencing batch reactor fed with 50 mg NH4 (+)-N L(-1) and operated during 4 months. Complete removal of ammonium and m-cresol was achieved independently of the initial concentration of aromatic compound in all the assays. Up to 25 mg m-cresol-C L(-1) (C/N ratio of 0.5), the nitrifying yield (Y-NO3 (-)) was 0.86 ± 0.05, indicating that the nitrate was the main product of the process; no biomass growth was detected. From 50 to 150 mg m-cresol-C L(-1) (1.0 ≤ C/N ≤ 3.0), simultaneous microbial growth and partial ammonium-to-nitrate conversion were obtained, reaching a maximum microbial total protein concentration of 0.763 g L(-1) (247 % of its initial value) and the lowest Y-NO3 (-) 0.53 ± 0.01 at 150 mg m-cresol-C L(-1). m-Cresol induced a significant decrease in the values of both specific rates of ammonium and nitrite oxidation, being the ammonium oxidation pathway the mainly inhibited. The nitrifying sludge was able to completely oxidize up to 150 mg m-cresol-C L(-1) by SBR cycle, reaching a maximum specific removal rate of 6.45 g m-cresol g(-1) microbial protein-N h(-1). The number of SBR cycles allowed a metabolic adaptation of the nitrifying consortium since nitrification inhibition decreased and faster oxidation of m-cresol took place throughout the cycles.

Association between ozone and asthma emergency department visits in Saint John, New Brunswick, Canada.

PubMed Central

Stieb, D M; Burnett, R T; Beveridge, R C; Brook, J R

1996-01-01

This study examines the relationship of asthma emergency department (ED) visits to daily concentrations of ozone and other air pollutants in Saint John, New Brunswick, Canada. Data on ED visits with a presenting complaint of asthma (n = 1987) were abstracted for the period 1984-1992 (May-September). Air pollution variables included ozone, sulfur dioxide, nitrogen dioxide, sulfate, and total suspended particulate (TSP); weather variables included temperature, humidex, dewpoint, and relative humidity. Daily ED visit frequencies were filtered to remove day of the week and long wave trends, and filtered values were regressed on air pollution and weather variables for the same day and the 3 previous days. The mean daily 1-hr maximum ozone concentration during the study period was 41.6 ppb. A positive, statistically significant (p < 0.05) association was observed between ozone and asthma ED visits 2 days later, and the strength of the association was greater in nonlinear models. The frequency of asthma ED visits was 33% higher (95% CI, 10-56%) when the daily 1-hr maximum ozone concentration exceeded 75 ppb (the 95th percentile). The ozone effect was not significantly influenced by the addition of weather or other pollutant variables into the model or by the exclusion of repeat ED visits. However, given the limited number of sampling days for sulfate and TSP, a particulate effect could not be ruled out. We detected a significant association between ozone and asthma ED visits, despite the vast majority of sampling days being below current U.S. and Canadian standards. Images Figure 1. A Figure 1. B Figure 2. Figure 3. PMID:9118879

Total lead concentration in new decorative enamel paints in Lebanon, Paraguay and Russia.

PubMed

Clark, C Scott; Speranskaya, Olga; Brosche, Sara; Gonzalez, Hebe; Solis, Daniela; Kodeih, Naji; Roda, Sandy; Lind, Caroline

2015-04-01

Lead concentrations in new enamel decorative paints were determined in three countries in different areas of the world where data were not previously available. The average total lead concentration of the enamel decorative paints purchased in Lebanon, Paraguay and Russia was 24,500ppm (ppm, dry weight), more than 270 times the current limit of 90ppm in Canada and in the United States. Sixty-three percent of these paints contained concentrations greater than 90ppm. Fifty-nine percent contained concentrations greater than 600ppm, the current limit in some countries. The maximum concentrations found were 236,000ppm in Lebanon, 169,000ppm in Paraguay and 52,900ppm in Russia. An average of 29% of the samples contained exceedingly high lead concentrations, >=10,000ppm. Five brands of paint were sampled in each of Lebanon and Paraguay and seven in Russia. Three colors from each brand were analyzed. For five of the six samples of the two brands in Lebanon with affiliations outside the country, the lead concentrations ranged from 1360ppm to 135,000ppm. In Lebanon the maximum concentration in the Egypt-affiliated brand (Sipes) was 135,000ppm and the maximum for the USA-affiliated brand (Dutch Boy) was 32,400ppm. Lead was not detected in any paints from the three of the four brands of paint purchased in Paraguay that had headquarters/affiliations in other countries (Brazil-Coralit), Germany (Suvinil) and USA (Novacor)). Two of the three paints from each of the other Paraguay brands contained high levels of lead with the maximum concentrations of 108,000 and 168,000ppm; one of these brands was manufactured under a license from ICI in the Netherlands. All of the paints purchased in Russia were from Russian brands and were manufactured in Russia. All three paints from one brand contained below detection levels of lead. The maximum levels of lead in the other six brands in Russia ranged from 3230 to 52,900ppm. The two brands with the highest lead concentration, TEKS and LAKRA, were produced by companies in the top three in market share.. Overall, lead concentrations were much higher in the colored paints such as red and yellow than in white paints. In each of the three countries a brand based in that country had a colored paint that either met a 90ppm limit or was close to meeting the limit-demonstrating that practical technology was available in each of these countries to produce low lead bright colored enamel decorative paints. Even though technology for producing paint without added lead existed in each of these countries, twenty-nine (29) percent of the paints analyzed contained exceedingly high concentrations (>=10,000ppm) of lead. Copyright © 2015 Elsevier Inc. All rights reserved.

Emerging organic contaminants in surface water and groundwater: a first overview of the situation in Italy.

PubMed

Meffe, Raffaella; de Bustamante, Irene

2014-05-15

This paper provides the first review of the occurrence of 161 emerging organic compounds (EOCs) in Italian surface water and groundwater. The reported EOCs belong to the groups of industrials, pharmaceuticals, estrogens and illicit drugs. Occurrence of 137 pesticides was also reported. The reviewed research works have been published between 1997 and 2013. The majority of the studies have been carried out in Northern Italy (n. 30) and to a lower extent in Central Italy (n. 13). Only a limited number of research studies report EOC concentrations in water resources of Southern Italy. The EOCs that have been more frequently studied are in the following descending order, pesticides (16), pharmaceuticals (15), industrials (13), estrogens (7) and illicit drugs (2). Research activities investigating the EOC occurrence in surface water are more numerous than those in groundwater. This is consistent with the higher complexity involved in groundwater sampling and EOC detection. Among the reported EOCs, industrials and pesticides are those occurring in both surface water and groundwater with the highest concentrations (up to 15 × 10(6) and 4.78 × 0(5)ng L(-1), respectively). Concentrations of pharmaceuticals in surface water reach a maximum of 3.59 × 10(3)ng L(-1), whereas only the antimicrobial agent josamycin has been encountered in groundwater with a concentration higher than 100 ng L(-1). Both estrogens and illicit drugs appeared in surface water with concentrations lower than 50 ng L(-1). Groundwater concentrations for estrogens were measured to be below the detection limits, whereas illicit drugs have so far not been studied in groundwater. The present review reveals the serious contamination status of Italian surface water and groundwater especially by pesticides, industrials and to a lower extent by pharmaceuticals and the necessity to foster the research on EOC occurrence in Italian water resources, in particular in Southern Italy where a limited number of investigations currently exist. Copyright © 2014 Elsevier B.V. All rights reserved.

Determinants of aerosol lung-deposited surface area variation in an urban environment.

PubMed

Reche, Cristina; Viana, Mar; Brines, Mariola; Pérez, Noemí; Beddows, David; Alastuey, Andrés; Querol, Xavier

2015-06-01

Ultrafine particles are characterized by a high surface area per mass. Particle surface has been reported to play a significant role in determining the toxicological activity of ultrafine particles. In light of this potential role, the time variation of lung deposited surface area (LDSA) concentrations in the alveolar region was studied at the urban background environment of Barcelona (Spain), aiming to asses which processes and sources govern this parameter. Simultaneous data on Black Carbon (BC), total particle number (N) and particle number size distribution were correlated with LDSA. Average LDSA concentrations in Barcelona were 37 ± 26 μm(2)cm(-3), levels which seem to be characteristic for urban environments under traffic influence across Europe. Results confirm the comparability between LDSA data provided by the online monitor and those calculated based on particle size distributions (by SMPS), and reveal that LDSA concentrations are mainly influenced by particles in the size range 50-200 nm. A set of representative daily cycles for LDSA concentrations was obtained by means of a k-means cluster technique. The contribution of traffic emissions to daily patterns was evidenced in all the clusters, but was quantitatively different. Traffic events under stable atmospheric conditions increased mean hourly background LDSA concentrations up to 6 times, attaining levels higher than 200 μm(2)cm(-3). However, under warm and relatively clean atmospheric conditions, the traffic rush hour contribution to the daily LDSA mean appeared to be lower and the contribution of new urban particle formation events (by photochemically induced nucleation) was detected. These nucleation events were calculated to increase average background LDSA concentrations by 15-35% (maximum LDSA levels=45-50 μm(2)cm(-3)). Thereby, it may be concluded that in the urban background of Barcelona road traffic is the main source increasing the aerosol surface area which can deposit on critical regions of the human lung, followed by nucleation episodes. Copyright © 2015 Elsevier B.V. All rights reserved.

Increasing arsenic concentrations in runoff from 12 small forested catchments (Czech Republic, Central Europe): patterns and controls.

PubMed

Novak, Martin; Erbanova, Lucie; Fottova, Daniela; Voldrichova, Petra; Prechova, Eva; Blaha, Vladimir; Veselovsky, Frantisek; Krachler, Michael

2010-08-01

The 40-year long period of heavy industrialization in Central Europe (1950-1990) was accompanied by burning of arsenic-rich lignite in thermal power plants, and accumulation of anthropogenic arsenic in forest soils. There are fears that retreating acidification may lead to arsenic mobilization into drinking water, caused by competitive ligand exchange. We present monthly arsenic concentrations in surface runoff from 12 headwater catchments in the Czech Republic for a period of 13 years (1996-2008). The studied area was characterized by a north-south gradient of decreasing pollution. Acidification, caused mainly by SOx and NOx emissions from power plants, has been retreating since 1987. Between 1996 and 2003, maximum arsenic concentrations in runoff did not change, and were < 1 ppb in the rural south and < 2 ppb in the industrial north. During the subsequent two years, 2004-2005, maximum arsenic concentrations in runoff increased, reaching 60% of the drinking water limit (10 ppb). Starting in 2006, maximum arsenic concentrations returned to lower values at most sites. We discuss three possible causes of the recent arsenic concentration maximum in runoff. We rule out retreating acidification and a pulse of high industrial emission rates as possible controls. The pH of runoff has not changed since 1996, and is still too low (<6.5) at most sites for an As-OH(-) ligand exchange to become significant. Elevated arsenic concentrations in runoff in 2004-2005 may reflect climate change through changing hydrological conditions at some, but not all sites. Dry conditions may result in elevated production of DOC and sulfur oxidation in the soil. Subsequent wet conditions may be accompanied by acidification leading to faster dissolution of arsenic-bearing sulfides, dissolution of arsenic-bearing Fe-oxyhydroxides, and elevated transport of arsenic sorbed on organic matter. Anaerobic domains exist in normally well-aerated upland soils for hours-to-days following precipitation events. 2010 Elsevier B.V. All rights reserved.

Correlation Of Giant Nuclei With Cloud Droplet Concentration

NASA Astrophysics Data System (ADS)

Jha, V.; Hudson, J. G.; Noble, S.

2011-12-01

The effect of giant nuclei (GN; larger than 1 micrometer particles produced by wind on the ocean surface) on warm rain has been debated for decades. During RICO (Rain in Cumulus over the Ocean) Hudson et al. (2011) found a negative correlation (R) between CCN concentrations at 1% supersaturation (S) and large cloud droplet concentrations (Fig. 1A). This reversal from positive R for CCN with total (or small) cloud droplet concentrations (left side of Fig. 1A) was explained by the greater competition for condensate, which thus limits droplet sizes when CCN concentrations are higher. The negative R increased in magnitude with altitude, and the droplet size where the maximum negative R occurred increased with altitude (Fig. 1A). However, at all altitudes this negative R decreased in magnitude for even larger cloud and drizzle drops (right side of Fig. 1A except highest altitude). The decrease in magnitude of the negative R was greater for increasing drop sizes at higher altitudes. Thus, at the higher altitudes, R for CCN with large drizzle drops was of low negative magnitude and even positive at the highest RICO altitudes. The disparity between CCN and drizzle drop concentrations precluded a causal relationship. But the high R between GN and drizzle drop concentrations at the highest altitudes (Fig. 1B) and the comparable concentrations indicated that GN were engendering drizzle. This is supported by the increasing R with altitude of the GN-drizzle drop R (right side of Fig. 1B). The conclusion of a GN-drizzle connection is also supported by the fact that CCN concentrations should inhibit drizzle. This analysis of Hudson et al. (2011) is here expanded to include correlations of CCN concentrations at lower S with cloud and drizzle drop concentrations to investigate intermediate relationships; i.e., between large nuclei (i.e., 0.1-1 micrometer; critical S 0.1-0.01%) and drizzle drop concentrations. A shortcoming of Hudson et al. (2011) was the small number of high altitude flights, which limited the significance of the R values. The very recent (July 2011) ICE-T project was a similar study in the same region (Caribbean). The greater number of high altitude cloud measurements during the summer season should provide better statistics to test the GN warm rain hypothesis.

Gonadal development of larval male Xenopus laevis exposed to atrazine in outdoor microcosms

USGS Publications Warehouse

Jooste, A.M.; Du Preez, L.H.; Carr, J.A.; Giesy, J.P.; Gross, T.S.; Kendall, R.J.; Smith, E.E.; Van Der Kraak, G. L.; Solomon, K.R.

2005-01-01

The potential effects of atrazine on gonadal development in metamorphs and subadults of the African clawed frog (Xenopus laevis) were studied under conditions of natural photoperiod and temperatures in outdoor microcosms from August 2002 to June 2003 in South Africa. Triplicate 1100 L microcosms for each nominal concentration of 0.0, 1, 10, and 25 ??g of atrazine/L were used. Measured atrazine concentrations varied <25% throughout the study, and no atrazine was detected in the control microcosms. Tadpoles developed well at all concentrations. On the basis of histological examination of testes of recently metamorphosed stage 66 frogs, 57% of the individuals in the reference group exhibited testicular oocytes as compared with 57, 59, and 39% of the 1, 10, and 25 ??g/L atrazine groups, respectively. The average prevalence of testicular oocytes for all of the treatments including the controls was 54% in a single testis, while, in 35% of individuals, testicular oocytes were observed in both testes. The number of testicular oocytes per individual ranged from 0 to 58 with means of 9.5, 9.8, 8.5, and 11.1 for the 0.0, 1, 10, and 25 ??g of atrazine/L groups, respectively. Ten months after metamorphosis, another subset of juveniles was examined, and the maximum number of testicular oocytes observed was five in one animal. The presence of testicular oocytes was not related to exposure to atrazine and may be a natural phenomenon during ontogeny. ?? 2005 American Chemical Society.

TiO2 dye sensitized solar cell (DSSC): linear relationship of maximum power point and anthocyanin concentration

NASA Astrophysics Data System (ADS)

Ahmadian, Radin

2010-09-01

This study investigated the relationship of anthocyanin concentration from different organic fruit species and output voltage and current in a TiO2 dye-sensitized solar cell (DSSC) and hypothesized that fruits with greater anthocyanin concentration produce higher maximum power point (MPP) which would lead to higher current and voltage. Anthocyanin dye solution was made with crushing of a group of fresh fruits with different anthocyanin content in 2 mL of de-ionized water and filtration. Using these test fruit dyes, multiple DSSCs were assembled such that light enters through the TiO2 side of the cell. The full current-voltage (I-V) co-variations were measured using a 500 Ω potentiometer as a variable load. Point-by point current and voltage data pairs were measured at various incremental resistance values. The maximum power point (MPP) generated by the solar cell was defined as a dependent variable and the anthocyanin concentration in the fruit used in the DSSC as the independent variable. A regression model was used to investigate the linear relationship between study variables. Regression analysis showed a significant linear relationship between MPP and anthocyanin concentration with a p-value of 0.007. Fruits like blueberry and black raspberry with the highest anthocyanin content generated higher MPP. In a DSSC, a linear model may predict MPP based on the anthocyanin concentration. This model is the first step to find organic anthocyanin sources in the nature with the highest dye concentration to generate energy.

The Effects of Nitrogen Addition on the Uptake and Allocation of Macro- and Micronutrients in Bothriochloa ischaemum on Loess Plateau in China

PubMed Central

Ai, Zemin; Wang, Guoliang; Liang, Chutao; Liu, Hongfei; Zhang, Jiaoyang; Xue, Sha; Liu, Guobin

2017-01-01

The effects of nitrogen (N) addition on the macro- and micronutrient concentrations, storage, and allocation of Bothriochloa ischaemum (L.) Keng, a native forage plant on the Loess Plateau in China remain unclear. We studied the effects of N addition at 0 (CK), 2.5 (N1), 5.0 (N2), and 10.0 (N3) g N m-2 y-1. N addition significantly decreased the available copper (Cu), zinc (Zn), and total Cu concentration, but significantly increased the available iron concentration in the soil. Cu, manganese (Mn), and sodium (Na) concentrations in aboveground tissues and potassium (K), magnesium, and Zn concentrations in belowground tissues significantly increased with N addition. Calcium (Ca) concentrations in belowground tissues decreased significantly. The ratios of above- to belowground Ca, Cu, Zn, and Mn significantly increased with N addition. The maximum ratios appeared at N2 for Cu, Zn, and Mn. The aboveground, belowground, and total biomass storage of studied nutrients significantly changed with N addition, and most attained maximum values under N2 treatment. The storage ratios of above- to belowground Cu, Zn, Mn, and Na attained maximum values at N2. We conclude that N addition significantly, but differentially influence the macro- and micronutrient concentrations and storage in B. ischaemum. B. ischaemum allocated and accumulated increased macro- and micronutrients to its aboveground tissues and exhibited high total storage when the amount of N addition reached 5 g N m-2 y-1. PMID:28970839

The Effects of Nitrogen Addition on the Uptake and Allocation of Macro- and Micronutrients in Bothriochloa ischaemum on Loess Plateau in China.

PubMed

Ai, Zemin; Wang, Guoliang; Liang, Chutao; Liu, Hongfei; Zhang, Jiaoyang; Xue, Sha; Liu, Guobin

2017-01-01

The effects of nitrogen (N) addition on the macro- and micronutrient concentrations, storage, and allocation of Bothriochloa ischaemum (L.) Keng, a native forage plant on the Loess Plateau in China remain unclear. We studied the effects of N addition at 0 (CK), 2.5 (N1), 5.0 (N2), and 10.0 (N3) g N m -2 y -1 . N addition significantly decreased the available copper (Cu), zinc (Zn), and total Cu concentration, but significantly increased the available iron concentration in the soil. Cu, manganese (Mn), and sodium (Na) concentrations in aboveground tissues and potassium (K), magnesium, and Zn concentrations in belowground tissues significantly increased with N addition. Calcium (Ca) concentrations in belowground tissues decreased significantly. The ratios of above- to belowground Ca, Cu, Zn, and Mn significantly increased with N addition. The maximum ratios appeared at N2 for Cu, Zn, and Mn. The aboveground, belowground, and total biomass storage of studied nutrients significantly changed with N addition, and most attained maximum values under N2 treatment. The storage ratios of above- to belowground Cu, Zn, Mn, and Na attained maximum values at N2. We conclude that N addition significantly, but differentially influence the macro- and micronutrient concentrations and storage in B. ischaemum . B. ischaemum allocated and accumulated increased macro- and micronutrients to its aboveground tissues and exhibited high total storage when the amount of N addition reached 5 g N m -2 y -1 .

Mercury distribution in ancient and modern sediment of northeastern Bering Sea

USGS Publications Warehouse

Nelson, C.H.; Pierce, D.E.; Leong, K.W.; Wang, F.F.H.

1975-01-01

Reconnaissance sampling of surface and subsurface sediment to a maximum depth of 80 m below the sea floor shows that typical values of 0.03 p.p.m. and anomalies of 0.2-1.3 p.p.m. mercury have been present in northeastern Bering Sea since Early Pliocene time. Values are highest in modern beach (maximum 1.3 and mean 0.22 p.p.m. Hg) and nearshore subsurface gravels (maximum 0.6 and mean 0.06 p.p.m. Hg) along the highly mineralized Seward Peninsula and in clayey silt rich in organic matter (maximum 0.16 and mean 0.10 p.p.m. Hg) throughout the region. Although gold mining may be partly responsible for high mercury levels in the modern beach near Nome, Alaska (maximum 0.45 p.p.m.), equally high or greater concentrations of mercury occur in buried Pleistocene sediments immediately offshore (maximum 0.6 p.p.m.) and in modern unpolluted beach sediments at Bluff (maximum 1.3 p.p.m.); this suggests that the contamination effects of mining may be no greater than natural concentration processes in the Seward Peninsula region. The mercury content of offshore surface sediment, even adjacent to mercury-rich beaches, corresponds to that of unpolluted marine and fresh-water sediment elsewhere. The normal values that prevail offshore may be attributable to entrapment of mercury-bearing heavy minerals on beaches near sources and/or dilution effects of offshore sedimentation. The few minor anomalies offshore occur in glacial drift derived from mercury source regions of Chukotka (Siberia) and Seward Peninsula; Pleistocene shoreline processes have reworked the drift to concentrate the heavy metals. The distribution pattern of mercury indicates that particulate mercury-bearing minerals have not been widely dispersed from onland deposits in quantities sufficient to increase mercury levels above normal in offshore sediments of Bering Sea; however, it shows that natural sedimentary processes can concentrate this mercury in beaches of the coastal zone where there already is concern because of potential pollution from man's activities.

Effects of pH and temperature on growth and glycerol production kinetics of two indigenous wine strains of Saccharomyces cerevisiae from Turkey

PubMed Central

Yalcin, Seda Karasu; Yesim Ozbas, Z.

2008-01-01

The study was performed in a batch system in order to determine the effects of pH and temperature on growth and glycerol production kinetics of two indigenous wine yeast strains Saccharomyces cerevisiae Kalecik 1 and Narince 3. The highest values of dry mass and specific growth rate were obtained at pH 4.00 for both of the strains. Maximum specific glycerol production rates were obtained at pH 5.92 and 6.27 for the strains Kalecik 1 and Narince 3, respectively. Kalecik 1 strain produced maximum 8.8 gL−1 of glycerol at pH 6.46. Maximum glycerol concentration obtained by the strain Narince 3 was 9.1 gL−1 at pH 6.48. Both yeasts reached maximum specific growth rate at 30°C. Optimum temperature range for glycerol production was determined as 25-30°C for the strain Kalecik 1. The strain Narince 3 reached maximum specific glycerol production rate at 30°C. Maximum glycerol concentrations at 30°C were obtained as 8.5 and 7.6 gL−1 for Kalecik 1 and Narince 3, respectively. PMID:24031225

Soil and Water Assessment Tool model predictions of annual maximum pesticide concentrations in high vulnerability watersheds.

PubMed

Winchell, Michael F; Peranginangin, Natalia; Srinivasan, Raghavan; Chen, Wenlin

2018-05-01

Recent national regulatory assessments of potential pesticide exposure of threatened and endangered species in aquatic habitats have led to increased need for watershed-scale predictions of pesticide concentrations in flowing water bodies. This study was conducted to assess the ability of the uncalibrated Soil and Water Assessment Tool (SWAT) to predict annual maximum pesticide concentrations in the flowing water bodies of highly vulnerable small- to medium-sized watersheds. The SWAT was applied to 27 watersheds, largely within the midwest corn belt of the United States, ranging from 20 to 386 km 2 , and evaluated using consistent input data sets and an uncalibrated parameterization approach. The watersheds were selected from the Atrazine Ecological Exposure Monitoring Program and the Heidelberg Tributary Loading Program, both of which contain high temporal resolution atrazine sampling data from watersheds with exceptionally high vulnerability to atrazine exposure. The model performance was assessed based upon predictions of annual maximum atrazine concentrations in 1-d and 60-d durations, predictions critical in pesticide-threatened and endangered species risk assessments when evaluating potential acute and chronic exposure to aquatic organisms. The simulation results showed that for nearly half of the watersheds simulated, the uncalibrated SWAT model was able to predict annual maximum pesticide concentrations within a narrow range of uncertainty resulting from atrazine application timing patterns. An uncalibrated model's predictive performance is essential for the assessment of pesticide exposure in flowing water bodies, the majority of which have insufficient monitoring data for direct calibration, even in data-rich countries. In situations in which SWAT over- or underpredicted the annual maximum concentrations, the magnitude of the over- or underprediction was commonly less than a factor of 2, indicating that the model and uncalibrated parameterization approach provide a capable method for predicting the aquatic exposure required to support pesticide regulatory decision making. Integr Environ Assess Manag 2018;14:358-368. © 2017 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC). © 2017 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC).

Dissolved lead in the deep Southeast Pacific Ocean: results of the 2013 US GEOTRACES cruise

NASA Astrophysics Data System (ADS)

Boyle, E. A.; Lee, J. M.; Zhang, J.; Echegoyen, Y.

2014-12-01

Lead (Pb) in the modern ocean is dominated by anthropogenic Pb, which has been evidenced by highly elevated seawater Pb concentrations and Pb stable isotope ratios (204Pb, 206Pb, 207Pb, and 208Pb) altered from pre-anthropogenic values. A number of studies have shown the human impact on oceanic Pb in many parts of the world ocean, but little Pb data has been available for the Southeast Pacific Ocean. In this presentation, we will show the dissolved Pb (<0.2µm) results from the US GEOTRACES cruise in October - December 2013, which sailed from Manta, Ecuador, to Tahiti along around 12 degrees south. Dissolved Pb concentrations from all 36 surface stations and deep (>1000m) Pb profiles from 18 stations will be presented, and the results will be also compared to our unpublished data from the BiG RAPA cruise in 2010, whose cruise track from Arica, Peru, to Easter Island is slightly south of the US GEOTRACES cruise. The BiG RAPA data showed that dissolved Pb concentrations of the southeast Pacific Ocean are relatively low, varying in the range of 8-20 pmol/kg at the surface with a slight maximum (14-22 pmol/kg) at around 400m depth, and 2-10 pmol/kg in deep waters below 1000m depth. The Pb concentrations were found to be higher at a marginal station off Peru, reaching 45 pmol/kg at the surface and 65 pmol/kg in the subsurface maximum at 150m depth, and varying between 17 and 23 pmol/kg in deep waters. Our dataset, along with the results from the BiG RAPA cruise, will provide the first overview on the dissolved Pb distribution of the southeast Pacific Ocean, which will further our understanding on the human impact on the global ocean.

Acarbose bioequivalence: exploration of new pharmacodynamic parameters.

PubMed

Zhang, Min; Yang, Jin; Tao, Lei; Li, Lingjun; Ma, Pengcheng; Fawcett, John Paul

2012-06-01

To investigate bioequivalence (BE) testing of an acarbose formulation in healthy Chinese volunteers through the use of recommended and innovative pharmacodynamic (PD) parameters. Following the Food and Drug Administration (FDA) guidance, a randomized, cross-over study of acarbose test (T) and reference (R) (Glucobay®) formulations was performed with a 1-week wash-out period. Preliminary pilot studies showed that the appropriate dose of acarbose was 2 × 50 mg, and the required number of subjects was 40. Serum glucose concentrations after sucrose administration (baseline) and co-administration of sucrose/acarbose on the following day were both determined. Three newly defined PD measures of glucose fluctuation (glucose excursion (GE), GE' (glucose excursion without the effect of the homeostatic glucose control), and fAUC (degree of fluctuation of serum glucose based on AUC)), the plateau glucose concentration (C(ss)), and time of maximum reduction in glucose concentration (T (max)) were tested in the evaluation. The adequacy of the two parameters recommended by the FDA, ΔC(SG,max) (maximum reduction in serum glucose concentration) and AUEC((0-4h)) (reduction in the AUC((0-4h)) of glucose between baseline and acarbose formulation) was also evaluated. The T (max) values were comparable, and the 90% confidence intervals of the geometric test/reference ratios (T/R) for ΔC(SG,max), C(ss), GE, and fAUC were all within 80-125%. The parameter GE' was slightly outside the limits, and the parameter AUEC((0-4h)) could not be computed due to the presence of negative values. In acarbose BE evaluation, while the recommended parameter ΔC(SG,max) is valuable, the combination of C(ss) and one of the newly defined glucose fluctuation parameters, GE, GE', and fAUC is preferable than AUEC((0-4h)). The acarbose test formulation can be initially considered to be bioequivalent to Glucobay®.

Influence of cytokinins, auxins and polyamines on in vitro mass multiplication of cotton (Gossypium hirsutum L. cv. SVPR2).

PubMed

Ganesan, M; Jayabalan, N

2006-06-01

In the present investigation, the influence of different forms of cytokinins, auxins and polyamines were tested for mass multiplication and regeneration of cotton. Initially, for the identification of effective concentration for multiple shoot induction, various concentrations of BAP, Kin and 2iP along with IAA and NAA were tested. Among tested concentrations, media fortified with MS salts; B5 vitamins; 30 g/l, glucose; 2.0 mg/l, 2iP; 2.0 mg/l, IAA and 0.7 % agar showed best response for multiplication of shoot tip explants (20 shoots per shoot tip explants). In nodal explants, maximum of 18.6 shoots were obtained in the media fortified with MS salts, B5 vitamins, 30 g/l, glucose, 2.0 mg/l, 2iP, 1.0 mg/l, NAA and 0.7 % agar. Effect of different concentrations of polyamines like spermidine and putrescine were also tested along with the above said multiplication media. Among the various treatments, 20 mg/l of putrescine showed best response and the multiple of shoots were increased to 26.5 shoots per shoot tip explants and 24.5 shoots per nodal explants. Elongation of shoots was achieved on multiple shoot induction medium. Significant number of roots were initiated in the medium supplemented with MS salts, vitamin B5 and IBA (2.0 mg/l). The frequency of root induction was increased by addition of, PVP (10 mg/l) along with root induction medium and after 2 weeks, the roots reached the maximum length of 22 cm. Further, these plantlets were hardened by using sand, soil and vermiculate in 1:1:1 ratio. The hardened plants were transferred to the environmental growth chamber for proper acclimatization. The hardened plants were then transferred to field for boll yielding and they exhibited 100% survival.

29 CFR 778.101 - Maximum nonovertime hours.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Maximum nonovertime hours. 778.101 Section 778.101 Labor... Requirements Introductory § 778.101 Maximum nonovertime hours. As a general standard, section 7(a) of the Act provides 40 hours as the maximum number that an employee subject to its provisions may work for an employer...

14 CFR 25.1505 - Maximum operating limit speed.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Maximum operating limit speed. 25.1505... Operating Limitations § 25.1505 Maximum operating limit speed. The maximum operating limit speed (V MO/M MO airspeed or Mach Number, whichever is critical at a particular altitude) is a speed that may not be...

14 CFR 25.1505 - Maximum operating limit speed.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Maximum operating limit speed. 25.1505... Operating Limitations § 25.1505 Maximum operating limit speed. The maximum operating limit speed (V MO/M MO airspeed or Mach Number, whichever is critical at a particular altitude) is a speed that may not be...

IMPACT OF SULPHUR DIOXIDE ON THE RESPIRATORY SYSTEM OF TBILISI POPULATION.

PubMed

Vepkhvadze, N; Kiladze, N; Khorbaladze, M; Kochoradze, T; Kugoti, I

2017-04-01

The possible relationship between levels of sulphur dioxide (SO2) in the air and the rate of respiratory diseases has been studied. Results of monitoring of main contaminants of outdoor air were analyzed and they are reflected in Environmental Report 2015. Information on morbidity by respiratory system diseases of Tbilisi population is has been taken from 2011-2015 reports of the National Center of Disease Control. Identified that there is no consistent correlation between sulphur dioxide concentration in the air and respiratory system disease rates in the population, including children. Obtained data demonstrated that during the study period maximum SO2 concentration was registered in 2015 - 0,14 mg/m3 (exceeding almost 3 times maximum permissible concentration - 0,5 mg/m3) and in the same year high morbidity rates are registered (incidence -18106,08), though the lowest rates are registered in 2011 (0,09 mg/m3), when incidence of respiratory system diseases in this period (13103.2) exceeds the rates registered in 2012, 2013 and 2014 (12736.4, 11336.3, 13009.0 accordingly). There is no direct correlation between the morbidity rates of 0-15 year old children and SO2 concentration. Maximum incidence rate is registered in 2015 (48487.0) and in the same year is also registered maximum concentration of SO2 (0,14 mg/m3), whereas the lowest rate is registered in 2013 (35538,70), when SO2 concentration in 2013 is lower only by 0.02 mg/m3 compared to the concentration in 2015. Direct correlation between morbidity with asthma in children and concentration of SO2 was not identified. Prevalence of asthma is minimal in 2014 (65,4), maximal in 2012 (207,1), whereas SO2 concentration in 2014 (0,13 mg/m3) exceeds the concentration in 2012 (0,12 mg/m3). It has to be considered, that besides SO2 there are many small intensity adverse factors, which are also risk factors for development of respiratory diseases. Isolated action of these factors with certain concentrations may not demonstrate any adverse effects on human health, but the combined effect of their action is stronger and obviously will affect general health and specifically - respiratory system. Implementation of urgent measures for further improvement of their ambient air quality has been recommended, which will be the basis for minimizing of many chronic diseases.

Anatomical and neuromuscular variables strongly predict maximum knee extension torque in healthy men.

PubMed

Trezise, J; Collier, N; Blazevich, A J

2016-06-01

This study examined the relative influence of anatomical and neuromuscular variables on maximal isometric and concentric knee extensor torque and provided a comparative dataset for healthy young males. Quadriceps cross-sectional area (CSA) and fascicle length (l f) and angle (θ f) from the four quadriceps components; agonist (EMG:M) and antagonist muscle activity, and percent voluntary activation (%VA); patellar tendon moment arm distance (MA) and maximal voluntary isometric and concentric (60° s(-1)) torques, were measured in 56 men. Linear regression models predicting maximum torque were ranked using Akaike's Information Criterion (AICc), and Pearson's correlation coefficients assessed relationships between variables. The best-fit models explained up to 72 % of the variance in maximal voluntary knee extension torque. The combination of 'CSA + θ f + EMG:M + %VA' best predicted maximum isometric torque (R (2) = 72 %, AICc weight = 0.38) and 'CSA + θ f + MA' (R (2) = 65 %, AICc weight = 0.21) best predicted maximum concentric torque. Proximal quadriceps CSA was included in all models rather than the traditionally used mid-muscle CSA. Fascicle angle appeared consistently in all models despite its weak correlation with maximum torque in isolation, emphasising the importance of examining interactions among variables. While muscle activity was important for torque prediction in both contraction modes, MA only strongly influenced maximal concentric torque. These models identify the main sources of inter-individual differences strongly influencing maximal knee extension torque production in healthy men. The comparative dataset allows the identification of potential variables to target (i.e. weaknesses) in individuals.

Pharmacokinetics and distribution of ceftazidime to milk after intravenous and intramuscular administration to lactating female dromedary camels (Camelus dromedarius).

PubMed

Goudah, Ayman M; Hasabelnaby, Sherifa M

2013-08-01

To determine the plasma disposition kinetics, absolute bioavailability, and milk concentrations of ceftazidime in healthy lactating female dromedary camels (Camelus dromedarius) following IV and IM administration of a single dose of 10 mg/kg (4.5 mg/lb). Prospective crossover study. 8 healthy adult lactating female dromedary camels. Camels received ceftazidime (10 mg/kg) IV and IM in a crossover study design with a 15-day washout period between treatments. Plasma and milk samples were collected at predetermined times for 48 hours after drug administration and analyzed by use of high-performance liquid chromatography. A 2-compartment open model best represented the plasma concentration-versus-time data after IV and IM administration of ceftazidime to camels. Plasma ceftazidime concentrations decreased biexponentially after IV administration with mean distribution and elimination half-lives of 0.3 hours and 2.85 hours, respectively. After IM administration, the mean maximum plasma concentration of ceftazidime was 32.43 μg/mL (1.21 hours after administration), mean elimination half-life was 3.20 hours, mean residence time was 4.84 hours, and mean systemic bioavailability was 93.72%. Distribution of ceftazidime from plasma to milk was rapid and extensive as indicated by the ratio of the area under the milk concentration-versus-time curve to the area under the plasma concentration-versus-time curve and the ratio of the maximum milk concentration to the maximum plasma concentration of ceftazidime after IV and IM administration. Results suggested that ceftazidime may be a useful treatment for female camels with mastitis caused by susceptible microorganisms.

Continuous protein concentration via free-flow moving reaction boundary electrophoresis.

PubMed

Kong, Fanzhi; Zhang, Min; Chen, Jingjing; Fan, Liuyin; Xiao, Hua; Liu, Shaorong; Cao, Chengxi

2017-07-28

In this work, we developed the model and theory of free-flow moving reaction boundary electrophoresis (FFMRB) for continuous protein concentration for the first time. The theoretical results indicated that (i) the moving reaction boundary (MRB) can be quantitatively designed in free-flow electrophoresis (FFE) system; (ii) charge-to-mass ratio (Z/M) analysis could provide guidance for protein concentration optimization; and (iii) the maximum processing capacity could be predicted. To demonstrate the model and theory, three model proteins of hemoglobin (Hb), cytochrome C (Cyt C) and C-phycocyanin (C-PC) were chosen for the experiments. The experimental results verified that (i) stable MRBs with different velocities could be established in FFE apparatus with weak acid/weak base neutralization reaction system; (ii) proteins of Hb, Cyt C and C-PC were well concentrated with FFMRB; and (iii) a maximum processing capacity and recovery ratio of Cyt C enrichment were 126mL/h and 95.5% respectively, and a maximum enrichment factor was achieved 12.6 times for Hb. All of the experiments demonstrated the protein concentration model and theory. In contrast to other methods, the continuous processing ability enables FFMRB to efficiently enrich diluted protein or peptide in large volume solution. Copyright © 2017 Elsevier B.V. All rights reserved.

Naturally occurring contaminants in the Piedmont and Blue Ridge crystalline-rock aquifers and Piedmont Early Mesozoic basin siliciclastic-rock aquifers, eastern United States, 1994–2008

USGS Publications Warehouse

Chapman, Melinda J.; Cravotta, Charles A.; Szabo, Zoltan; Lindsay, Bruce D.

2013-01-01

Groundwater quality and aquifer lithologies in the Piedmont and Blue Ridge Physiographic Provinces in the eastern United States vary widely as a result of complex geologic history. Bedrock composition (mineralogy) and geochemical conditions in the aquifer directly affect the occurrence (presence in rock and groundwater) and distribution (concentration and mobility) of potential naturally occurring contaminants, such as arsenic and radionuclides, in drinking water. To evaluate potential relations between aquifer lithology and the spatial distribution of naturally occurring contaminants, the crystalline-rock aquifers of the Piedmont and Blue Ridge Physiographic Provinces and the siliciclastic-rock aquifers of the Early Mesozoic basin of the Piedmont Physiographic Province were divided into 14 lithologic groups, each having from 1 to 16 lithochemical subgroups, based on primary rock type, mineralogy, and weathering potential. Groundwater-quality data collected by the U.S. Geological Survey (USGS) National Water-Quality Assessment (NAWQA) Program from 1994 through 2008 from 346 wells and springs in various hydrogeologic and land-use settings from Georgia through New Jersey were compiled and analyzed for this study. Analyses for most constituents were for filtered samples, and, thus, the compiled data consist largely of dissolved concentrations. Concentrations were compared to criteria for protection of human health, such as U.S. Environmental Protection Agency (USEPA) drinking water maximum contaminant levels and secondary maximum contaminant levels or health-based screening levels developed by the USGS NAWQA Program in cooperation with the USEPA, the New Jersey Department of Environmental Protection, and Oregon Health & Science University. Correlations among constituent concentrations, pH, and oxidation-reduction (redox) conditions were used to infer geochemical controls on constituent mobility within the aquifers. Of the 23 trace-element constituents evaluated, arsenic, manganese, and zinc were detected in one or more water samples at concentrations greater than established human health-based criteria. Arsenic concentrations typically were less than 1 microgram per liter (µg/L) in most groundwater samples; however, concentrations of arsenic greater than 1 µg/L frequently were detected in groundwater from clastic lacustrine sedimentary rocks of the Early Mesozoic basin aquifers and from metamorphosed clastic sedimentary rocks of the Piedmont and Blue Ridge crystalline rock aquifers. Groundwater from these rock units had elevated pH compared to other rock units evaluated in this study. Of the nine samples for which arsenic concentration was greater than 10 µg/L, six were classified as oxic and three as anoxic, and seven had pH of 7.2 or greater. Manganese concentrations typically were less than 10 µg/L in most samples; however, 8.3 percent of samples from the Piedmont and Blue Ridge crystalline-rock aquifers and 3.0 percent of samples from the Early Mesozoic basin siliciclastic rock aquifers had manganese concentrations greater than the 300-µg/L health-based screening level. The positive correlation of manganese with iron and ammonia and the negative correlation of manganese with dissolved oxygen and nitrate are consistent with the reductive dissolution of manganese oxides in the aquifer. Zinc concentrations typically were less than 10 µg/L in the groundwater samples considered in the study, but 0.4 percent and 5.5 percent of the samples had concentrations greater than the health-based screening level of 2,000 µg/L and one-tenth of the health-based screening level, respectively. The mean rank concentration of zinc in groundwater from the quartz-rich sedimentary rock lithologic group was greater than that for other lithologic groups even after eliminating samples collected from wells constructed with galvanized casing. Approximately 90 percent of 275 groundwater samples had radon-222 concentrations that were greater than the proposed alternative maximum contaminant level of 300 picocuries per liter. In contrast, only 2.0 percent of 98 samples had combined radium (radium-226 plus radium-228) concentrations greater than the maximum contaminant level of 5.0 picocuries per liter, and 0.6 percent of 310 samples had uranium concentrations greater than the maximum contaminant level of 30 µg/L. Radon concentrations were highest in the Piedmont and Blue Ridge crystalline-rock aquifers, especially in granite, and elevated median concentrations were noted in the Piedmont Early Mesozoic basin aquifers, but without the extreme maximum concentrations found in the crystalline rocks (granites). Although the siliciclastic lithologies had a greater frequency of elevated uranium concentrations, radon and radium were commonly detected in water from both siliciclastic and crystalline lithologies. Uranium concentrations in groundwater from clastic sedimentary and clastic lacustrine/evaporite sedimentary lithologic groups within the Early Mesozoic basin aquifers, which had median concentrations of 3.6 and 3.1 µg/L, respectively, generally were higher than concentrations for other siliciclastic lithologic groups, which had median concentrations less than 1 µg/L. Although 89 percent of the 260 samples from crystalline-rock aquifers had uranium concentrations less than 1 µg/L, 0.8 percent had uranium concentrations greater than the 30-µg/L maximum contaminant level, and 6.5 percent had concentrations greater than 3 µg/L.

Light dependence of carboxylation capacity for C3 photosynthesis models

USDA-ARS?s Scientific Manuscript database

Photosynthesis at high light is often modelled by assuming limitation by the maximum capacity of Rubisco carboxylation at low carbon dioxide concentrations, by electron transport capacity at higher concentrations, and sometimes by triose-phosphate utilization rate at the highest concentrations. Pho...

Rotation sensitivity analysis of a two-dimensional array of coupled resonators

NASA Astrophysics Data System (ADS)

Zamani Aghaie, Kiarash; Vigneron, Pierre-Baptiste; Digonnet, Michel J. F.

2015-03-01

In this paper, we study the rotation sensitivity of a gyroscope made of a two-dimensional array of coupled resonators consisting of N columns of one-dimensional coupled resonant optical waveguides (CROWs) connected by two bus waveguides, each CROW consisting of M identical ring resonators. We show that the maximum rotation sensitivity of this structure is a strong function of the parity of the number of rows M. For an odd number of rows, and when the number of columns is small, the maximum sensitivity is high, and it is slightly lower than the maximum sensitivity of a single-ring resonator with two input/output waveguides (the case M = N = 1), which is a resonant waveguide optical gyroscope (RWOG). For an even M and small N, the maximum sensitivity is much lower than that of the RWOG. Increasing the number columns N increases the sensitivity of an even-row 2D CROW sublinearly, as N0.39, up to 30 columns. In comparison, the maximum sensitivity of an RWOG of equal area increases faster, as √N. The sensitivity of the 2D CROW therefore always lags behind that of the RWOG. For a 2×2 CROW, if the spacing between the columns L is increased sufficiently the maximum sensitivity increases linearly with L due to the presence of a composite Mach- Zehnder interferometer in the structure. However, for equal footprints this sensitivity is also not larger than that of a single-ring resonator. Regardless of the number of rows and columns and the spacing, for the same footprint and propagation loss, a 2D CROW gyroscope is not more sensitive than an RWOG.

Pressure Effects on the Self-Extinguishment Limits of Aerospace Materials

NASA Technical Reports Server (NTRS)

Hirsch, David B.; Williams, James H.; Haas, Jon P.; Beeson, Harold D.; Ruff, Gary A.; Pedley, Michael D.

2009-01-01

The Orion Crew Exploration Vehicle Module (CM) is being designed to operate in an atmosphere of up to 30% oxygen at a pressure of 10.2 psia for lunar missions. Spacecraft materials selection is based on an upward flammability test conducted in a closed chamber under the worst expected conditions of pressure and oxygen concentration. Material flammability depends on both oxygen concentration and pressure but, since oxygen concentration is the primary driver, all materials are certified in the 30% oxygen, 10.2 psia environment. Extensive data exist from the Shuttle Program at this condition which used relatively the same test methodology as currently used in the Constellation Program. When the CM returns to Earth, a snorkel device will be activated after splashdown to provide outside air to the crew; however, for operational reasons, it is desirable to maximize the time the crew is able to breathe cabin air before the snorkel device is activated. To maximize this time, it has been proposed to raise the partial pressure of oxygen in the CM immediately before reentry while maintaining the total cabin pressure at 14.7 psia. In addition, it has been proposed to leak-test the Orion CM with ambient air at a maximum pressure of 17.3 psia. No data exist to assess how high the cabin oxygen concentration can be at 14.7 psia or 17.3 psia. One is to re-test a large number of materials at these pressures at a significant cost. However, since the maximum oxygen concentration (MOC) at which a material will self-extinguish has been determined for a variety of spacecraft materials as a function of pressure, a second alternative is to use existing data to estimate the MOC at 14.7 psia and 17.3 psia. This data will be examined in this paper and an analysis presented to determine the oxygen concentrations at the increased pressures that will result in self-extinguishment of a material. This analysis showed that the oxygen concentration for the Orion CM at 14.7 psia cannot be set higher than 25.6% without potentially invalidating the materials flammability certification in 30% oxygen at 10.2 psia for some materials. Materials certified under these conditions would still be self-extinguishing in ambient air at 17.3 psia. alternative

Induction of DNA strand breaks and expression of HSP70 and GRP78 homolog by cadmium in the marine sponge Suberites domuncula.

PubMed

Schröder, H C; Hassanein, H M; Lauenroth, S; Koziol, C; Mohamed, T A; Lacorn, M; Steinhart, H; Batel, R; Müller, W E

1999-01-01

The marine sponge Suberites domuncula was used as a bioindicator to study the effects of cadmium on the occurrence of DNA strand breakage and on the induction of the expression of the stress biomarkers, heat shock protein 70 (HSP70) and glucose-regulated protein 78 (GRP78) homolog. The cDNA encoding GRP78 homolog from S. domuncula was isolated and characterized. The GRP78 cDNA has a length of 2.1 kb and displays characteristic features of the HSP70 family; it encodes an aa sequence of Mr 72,000. Exposure of S. domuncula to 1 mg/L of cadmium chloride for 24 h caused a strong (16. 6-fold) increase in cadmium content to 7.7 microg/g wet weight of sponge tissue; after an incubation period of 6 days, the accumulation was 20.4-fold. The increase in cadmium content was paralleled by a transient decrease in zinc content at days 1 and 3. Exposure of S. domuncula to cadmium chloride also resulted in a marked increase in the number of DNA single strand breaks, as assessed by a recently developed fast and sensitive microplate assay. The maximum increase in DNA damage was observed after an incubation of 12 h in the presence of 1 mg/L of cadmium chloride; after longer incubation, the number of damaged sites decreased, most likely due to DNA repair. Quantitative analysis of the expression of HSP70 (Mr 73 kDa) revealed that onset of maximal levels of HSP70 depends on the concentration of cadmium chloride in the ambient seawater. Maximal induction (8.9-fold increase compared to control) of HSP70 following exposure to 1 mg/L of cadmium chloride was found after 12 h, while longer incubation periods (3-6 days) were needed to reach maximum levels of HSP70 in the presence of lower concentrations of cadmium chloride (0.1 mg/L and 0.01 mg/L). Northern blot analysis revealed that the level of the 2.0 kb sponge GRP78 homolog mRNA transiently increased under cadmium stress; the maximum increase in the presence of 0.1 mg/L of cadmium chloride was observed at day 3. Our results suggest that sponges are useful indicator organisms to assess the genotoxic risks of cadmium pollution in marine environments.

Assessing spatial and temporal variability of phytoplankton communities' composition in the Iroise Sea ecosystem (Brittany, France): A 3D modeling approach. Part 2: Linking summer mesoscale distribution of phenotypic diversity to hydrodynamism

NASA Astrophysics Data System (ADS)

Cadier, Mathilde; Sourisseau, Marc; Gorgues, Thomas; Edwards, Christopher A.; Memery, Laurent

2017-05-01

Tidal front ecosystems are especially dynamic environments usually characterized by high phytoplankton biomass and high primary production. However, the description of functional microbial diversity occurring in these regions remains only partially documented. In this article, we use a numerical model, simulating a large number of phytoplankton phenotypes to explore the three-dimensional spatial patterns of phytoplankton abundance and diversity in the Iroise Sea (western Brittany). Our results suggest that, in boreal summer, a seasonally marked tidal front shapes the phytoplankton species richness. A diversity maximum is found in the surface mixed layer located slightly west of the tidal front (i.e., not strictly co-localized with high biomass concentrations) which separates tidally mixed from stratified waters. Differences in phenotypic composition between sub-regions with distinct hydrodynamic regimes (defined by vertical mixing, nutrients gradients and light penetration) are discussed. Local growth and/or physical transport of phytoplankton phenotypes are shown to explain our simulated diversity distribution. We find that a large fraction (64%) of phenotypes present during the considered period of September are ubiquitous, found in the frontal area and on both sides of the front (i.e., over the full simulated domain). The frontal area does not exhibit significant differences between its community composition and that of either the well-mixed region or an offshore Deep Chlorophyll Maximum (DCM). Only three phenotypes (out of 77) specifically grow locally and are found at substantial concentration only in the surface diversity maximum. Thus, this diversity maximum is composed of a combination of ubiquitous phenotypes with specific picoplankton deriving from offshore, stratified waters (including specific phenotypes from both the surface and the DCM) and imported through physical transport, completed by a few local phenotypes. These results are discussed in light of the three-dimensional general circulation at frontal interfaces. Processes identified by this study are likely to be common in tidal front environments and may be generalized to other shallow, tidally mixed environments worldwide.

Ambient lead measurements in Cairo, Egypt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Howes, J.E. Jr.; Labib, M.; Samaha, N.

1999-07-01

The Cairo Air Improvement Project (CAIP) has established a network of 36 stations to monitor airborne lead levels in the Greater Cairo Area. Data obtained during the first 4 months of the monitoring program indicates that lead levels in ambient air significantly exceed the Government of Egypt's (GOE) Law Number 4 (1994) limit of 1 {micro} g/m{sup 3} (annual mean) in areas downwind of secondary lead smelters and in heavily trafficked areas. The highest mean and single sampling event lead levels were observed in the heavily industrialized areas of Shoubra el-Kheima and Tebbin. At two sites in Shoubra el-Kheima, meanmore » and maximum lead levels were determined to be approximately 20 {micro} g/m{sup 3} and 79 {micro} g/m{sup 3}, respectively. At three sites located in areas of high motor vehicle traffic in the central part of the city, the mean lead level was about 4 {micro} g/m{sup 3} and the maximum levels ranged from approximately 10 x 20 {micro} g/m{sup 3}. Of the remainder of the sites, the mean lead concentrations were 2fd3 {micro} g/m{sup 3} at three sites, 1 P2 {mu} g/m{sup 3} at 16 sites, and below 1 {micro} g/m{sup 3} at eight sites. Lead levels in areas devoted primarily to residential use were generally less than 2 {micro} g/m{sup 3}. The maximum mean monthly PM{sub 10} lead value measured at fugitive emission monitoring sites near lead smelters was approximately 73 {micro} g/m{sup 3}. The maximum lead concentration measured during a single sampling event was 180 {micro} g/m{sup 3}. Generally lower lead levels were observed in December due to regulation action that resulted in some suspension of smelting operations and to approximately 180-degree wind direction shifts that typically occur during this period of the year. The GOE is working vigorously to eliminate the lead problem in Egypt through implementation of the Lead Exposure Action Plan (LEAP). A major component of LEAP is the Lead Smelter Action Plan (LSAP).« less

Vascular Graft Impregnation with Antibiotics: The Influence of High Concentrations of Rifampin, Vancomycin, Daptomycin, and Bacteriophage Endolysin HY-133 on Viability of Vascular Cells.

PubMed

Herten, Monika; Idelevich, Evgeny A; Sielker, Sonja; Becker, Karsten; Scherzinger, Anna S; Osada, Nani; Torsello, Giovanni B; Bisdas, Theodosios

2017-06-27

BACKGROUND Rifampin-soaked synthetic prosthetic grafts have been widely used for prevention or treatment of vascular graft infections (VGIs). This in vitro study investigated the effect of the antibiotics daptomycin and vancomycin and the new recombinant bacteriophage endolysin HY-133 on vascular cells, as potential alternatives compared to rifampin. MATERIAL AND METHODS Primary human ECs, vascular smooth muscle cells (vSMC), and fibroblasts were cultivated in 96-well plates and incubated with rifampin, daptomycin, vancomycin, and endolysin HY-133 for 24 h. Subsequently, after washing, cell viability was determined by measuring mitochondrial ATP concentration. Antibiotics were used in their corresponding minimum and maximum serum concentrations, in decimal multiples and in maximum soaking concentration. The experiments were performed in triplicate. RESULTS The 10-fold max serum concentrations of rifampin, daptomycin, and vancomycin did not influence viability of EC and vSMC (100 µg/ml, p>0.170). Higher concentrations of rifampin (>1 mg/ml) significantly (p<0.001) reduced cell viability of all cell types. For the other antibiotics, high concentrations (close to maximum soaking concentration) were most cytotoxic for EC and vSMC and fibroblasts (p<0.001). Endolysin did not display any cytotoxicity towards vascular cells. CONCLUSIONS Results of this in vitro study show the high cytotoxicity of rifampin against vascular cells, and may re-initiate the discussion about the benefit of prophylactic pre-soaking in high concentrations of rifampin. Further studies are necessary to determine the influence of rifampin on the restoration of vessel functionality versus its prophylactic effect against VGIs. Future use of recombinant phage endolysins for alternative prophylactic strategies needs further investigations.

Changes in the structure of nuclei between the magic neutron numbers 50 and 82 as indicated by a rotating-cluster analysis of the energy values of the first 2+ excited states of isotopes of cadmium, tin, and tellurium

PubMed Central

Pauling, Linus

1981-01-01

Values of R, the radius of rotation of the rotating cluster, are calculated from the observed values of the energy of the lowest 2+ states of the even isotopes of 48Cd, 50Sn, and 52Te with the assumption that the cluster is α, p2, and α, respectively. R shows a maximum at ≈N = 58, a minimum at ≈N = 62, and a second maximum at ≈N = 70. The increase to the first maximum is interpreted as resulting from the overcrowding of spherons (alphas and tritons) in the mantle (outer layer) of the nuclei, causing the cluster to change from rotating in the mantle to skimming over its surface; the decrease to the minimum results from the addition of three dineutrons to the core, expanding the mantle and permitting the rotating cluster to begin to drop back into it; and the increase to the second maximum results from the overcrowding of the larger mantle surrounding the core containing the semi-magic number 14 of neutrons rather than the magic number 8 for N = 50. The decrease after the second maximum results from the further increase in the number of core neutrons to 20, corresponding to the magic number 82. Some additional evidence for the change to an intermediate structure between N = 50 and N = 82 is also discussed. PMID:16593084

Using tsunami deposits to determine the maximum depth of benthic burrowing

PubMed Central

Shirai, Kotaro; Murakami-Sugihara, Naoko

2017-01-01

The maximum depth of sediment biomixing is directly related to the vertical extent of post-depositional environmental alteration in the sediment; consequently, it is important to determine the maximum burrowing depth. This study examined the maximum depth of bioturbation in a natural marine environment in Funakoshi Bay, northeastern Japan, using observations of bioturbation structures developed in an event layer (tsunami deposits of the 2011 Tohoku-Oki earthquake) and measurements of the radioactive cesium concentrations in this layer. The observations revealed that the depth of bioturbation (i.e., the thickness of the biomixing layer) ranged between 11 and 22 cm, and varied among the sampling sites. In contrast, the radioactive cesium concentrations showed that the processing of radioactive cesium in coastal environments may include other pathways in addition to bioturbation. The data also revealed the nature of the bioturbation by the heart urchin Echinocardium cordatum (Echinoidea: Loveniidae), which is one of the important ecosystem engineers in seafloor environments. The maximum burrowing depth of E. cordatum in Funakoshi Bay was 22 cm from the seafloor surface. PMID:28854254

Using tsunami deposits to determine the maximum depth of benthic burrowing.

PubMed

Seike, Koji; Shirai, Kotaro; Murakami-Sugihara, Naoko

2017-01-01

The maximum depth of sediment biomixing is directly related to the vertical extent of post-depositional environmental alteration in the sediment; consequently, it is important to determine the maximum burrowing depth. This study examined the maximum depth of bioturbation in a natural marine environment in Funakoshi Bay, northeastern Japan, using observations of bioturbation structures developed in an event layer (tsunami deposits of the 2011 Tohoku-Oki earthquake) and measurements of the radioactive cesium concentrations in this layer. The observations revealed that the depth of bioturbation (i.e., the thickness of the biomixing layer) ranged between 11 and 22 cm, and varied among the sampling sites. In contrast, the radioactive cesium concentrations showed that the processing of radioactive cesium in coastal environments may include other pathways in addition to bioturbation. The data also revealed the nature of the bioturbation by the heart urchin Echinocardium cordatum (Echinoidea: Loveniidae), which is one of the important ecosystem engineers in seafloor environments. The maximum burrowing depth of E. cordatum in Funakoshi Bay was 22 cm from the seafloor surface.

Separation of electrolyte solutions by reverse osmosis.

PubMed

Starov, V M; Churaev, N V

1993-05-09

The paper presented is subdivided into two parts. The first one includes a survey of current notions concerning the physico-chemical nature of interaction potential phi between dissolved molecules or ions and water with a membrane material. Special attention is paid to the structural potential and the potential of image forces. The main conclusion is that the potential of interaction phi determines the major part of phenomena which are relevant for reverse osmosis (RO) separation. In the second part the distribution coefficient gamma = exp (phi) is supposed to be known and a survey of theoretical investigations of RO processes is undertaken. The so called homogeneous model of RO membranes is employed and concentration polarization is taken into account. Two main points in this investigation should be emphasized, that is, taking into account concentration polarization and a theory of RO separation of electrolyte mixtures. The maximum value of rejection coefficient and corresponding optimum velocity of filtration are calculated. Negative rejection of some ions from the mixture is explained, as well as a change in pH of filtrate. The streaming potential is calculated as a function of Peclet number, distribution coefficients, membrane charge and so on in all cases. The suggested theory gives the possibility to explain a number of phenomena in RO separation of electrolyte solutions.

Recent and past dust concentrations and fluxes from a developing array of Antarctic ice cores

NASA Astrophysics Data System (ADS)

McConnell, J. R.; Anschütz, H.; Baggenstos, D.; Das, S. B.; Isaksson, E. D.; Lawrence, R.; Layman, L.; Maselli, O.; Severinghaus, J. P.; Sigl, M.; Petit, J. R.; Grente, B.

2012-12-01

Continental dust is an important component of climate forcing, both because of its interaction with incoming solar and outgoing long wave radiation and because of its impact on albedo when deposited on bright surfaces such as fresh snow. Continental dust may also play an important role in ocean fertilization and carbon sequestration. Because the lifetime of dust aerosol in the atmosphere is only on the order of days to weeks, spatial and temporal variability in concentrations and fluxes is high and understanding of recent and long term changes is limited. Here we present and discuss detailed continuous, high depth resolution measurements of a range of dust proxies in a developing array of Antarctic ice cores. Included are traditional proxies such as non-sea-salt (nss) calcium and insoluble particle number and size distribution as well as less traditional proxies such as aluminum, vanadium, manganese, rare earth elements, and nss uranium which together provide important insights into how dust sources and transport may have changed in the past. The array includes a number of new shallow ice core records from East and West Antarctica spanning recent centuries to millennia, as well as Last Glacial Maximum to early Holocene records from the deep WAIS Divide and Taylor Glacier Horizontal ice cores.

Effects of different vibration exercises on bench press.

PubMed

Marín, P J; Torres-Luque, G; Hernández-García, R; García-López, D; Garatachea, N

2011-10-01

This study was undertaken to analyze the effects of different vibration recovery strategies via feet or hands on the number of repetitions performed and on mean velocity, peak velocity and blood lactate concentration during consecutive bench-press sets. 9 elite judo athletes performed 3 sets of bench press at 60% of one-repetition maximum (1RM), leading to failure and allowing a 180 s rest period between sets. During the rest period, 1 of the 3 following procedures was performed: 150 s rest plus 30 s push-up vibration exercise (Push-up), 150 s rest plus 30 s squat vibration exercise (Squat) or 180 s only rest (Passive). Statistical analysis revealed that the Squat condition resulted in a significant increase in the number of repetitions achieved, in comparison with all other rest strategies. However, kinematic parameters and blood lactate concentration were not affected by vibration. These data suggest that a vibration stimulus applied to the feet, between sets, can result in positive improvements in upper body resistance exercise performance. Although the mechanisms are not fully understood, this positive effect of vibration could be due to an increased motor cortex excitability and voluntary drive. © Georg Thieme Verlag KG Stuttgart · New York.

Diffusion of Drag-Reducing Polymers within a High-Reynolds-Number, Rough-Wall Turbulent Boundary Layer

NASA Astrophysics Data System (ADS)

Elbing, Brian; Perlin, Marc; Dowling, David; Solomon, Michael; Ceccio, Steven

2008-11-01

Two experiments were conducted to investigate polymer drag reduction (PDR) within high Reynolds number (to 200 million based on downstream distance), rough-wall turbulent boundary layers. The first experiment was conducted at the U.S. Navy's Large Cavitation Channel on a 12.9 m long flat-plate at speeds to 20 m/s with the surface hydraulically smooth and fully rough. Local skin-friction measurements on the smooth and rough surfaces had maximum PDR levels of 65 and 75 percent, respectively. However, PDR decreased with increasing downstream distance and flow speed more rapidly on the rough surface, and at the top speed no measureable level of PDR was observed. The roughness-induced increased diffusion was quantified with near-wall concentration measurements and the second experiment, which measured concentration profiles on a 0.94 m long flat-plate with three surface conditions: smooth, 240-grit, and 60-grit sandpaper. The increased diffusion does not fully explain the smooth-rough PDR differences observed in the first experiment. Rheological analysis of drawn samples from the first experiment indicates that polymer degradation (chain scission) could be responsible for the remaining loss of rough-wall PDR. These results have implications for the cost effectiveness of PDR for surface ships.

Artificial receptor-functionalized nanoshell: facile preparation, fast separation and specific protein recognition

NASA Astrophysics Data System (ADS)

Ouyang, Ruizhuo; Lei, Jianping; Ju, Huangxian

2010-05-01

This work combined molecular imprinting technology with superparamagnetic nanospheres as the core to prepare artificial receptor-functionalized magnetic nanoparticles for separation of homologous proteins. Using dopamine as a functional monomer, novel surface protein-imprinted superparamagnetic polydopamine (PDA) core-shell nanoparticles were successfully prepared in physiological conditions, which could maintain the natural structure of a protein template and achieved the development of molecularly imprinted polymers (MIPs) from one dimension to zero dimension for efficient recognition towards large biomolecules. The resultant nanoparticles could be used for convenient magnetic separation of homologous proteins with high specificity. The nanoparticles possessed good monodispersibility, uniform surface morphology and high saturation magnetization value. The bound amounts of template proteins measured by both indirect and direct methods were in good agreement. The maximum number of imprinted cavities on the surface of the bovine hemoglobin (Hb)-imprinted nanoshell was 2.21 × 1018 g - 1, which well matched their maximum binding capacity toward bovine Hb. Both the simple method for preparation of MIPs and the magnetic nanospheres showed good application potential in fast separation, effective concentration and selective biosensing of large protein molecules.

Influence of carbon source and inoculum type on anaerobic biomass adhesion on polyurethane foam in reactors fed with acid mine drainage.

PubMed

Rodriguez, Renata P; Zaiat, Marcelo

2011-04-01

This paper analyzes the influence of carbon source and inoculum origin on the dynamics of biomass adhesion to an inert support in anaerobic reactors fed with acid mine drainage. Formic acid, lactic acid and ethanol were used as carbon sources. Two different inocula were evaluated: one taken from an UASB reactor and other from the sediment of a uranium mine. The values of average colonization rates and the maximum biomass concentration (C(max)) were inversely proportional to the number of carbon atoms in each substrate. The highest C(max) value (0.35 g TVS g(-1) foam) was observed with formic acid and anaerobic sludge as inoculum. Maximum colonization rates (v(max)) were strongly influenced by the type of inoculum when ethanol and lactic acid were used. For both carbon sources, the use of mine sediment as inoculum resulted in a v(max) of 0.013 g TVS g(-1) foam day(-1), whereas 0.024 g TVS g(-1) foam day(-1) was achieved with anaerobic sludge. Copyright © 2011 Elsevier Ltd. All rights reserved.

Detergent assisted ultrasonication aided in situ transesterification for biodiesel production from oleaginous yeast wet biomass.

PubMed

Yellapu, Sravan Kumar; Kaur, Rajwinder; Tyagi, Rajeshwar D

2017-01-01

In situ transesterification of oleaginous yeast wet biomass for fatty acid methyl esters (FAMEs) production using acid catalyst, methanol with or without N-Lauroyl sarcosine (N-LS) treatment was performed. The maximum FAMEs yield obtained with or without N-LS treatment in 24h reaction time was 96.1±1.9 and 71±1.4% w/w, respectively. The N-LS treatment of biomass followed by with or without ultrasonication revealed maximum FAMEs yield of 94.3±1.9% and 82.9±1.8% w/w using methanol to lipid molar ratio 360:1 and catalyst concentration 360mM (64μL H 2 SO 4 /g lipid) within 5 and 25min reaction time, respectively. The FAMEs composition obtained in in situ transesterification was similar to that obtained with conventional two step lipid extraction and transesterification process. Biodiesel fuel properties (density, kinematic viscosity, cetane number and total glycerol) were in accordance with international standard (ASTM D6751), which suggests the suitability of biodiesel as a fuel. Copyright © 2016 Elsevier Ltd. All rights reserved.

Optimization of high molecular weight pullulan production by Aureobasidium pullulans in batch fermentations.

PubMed

Gibson, Larry H; Coughlin, Robert W

2002-01-01

Of five strains of Aureobasidium pullulans studied, NRRL Y-2311-1 yielded the highest titer (26.2 g/L) of pullulan and formed the lowest amount of melanin-like pigment. Sucrose was superior to glucose as the carbon and energy source on the basis of yield and titer of pullulan produced. Pullulan titer was higher (26.2 vs 5.1 g/L), biomass concentration was lower (6.9 vs 12.7 g/L), and DO was lower (0 vs 60% of saturation) when the fermenter was agitated by a marine propeller compared to Rushton impellers. Pullulan produced by strain NRRL Y-2311-1 ranged in weight-average molar mass (M(w)) from 486 KDa and number-average molar mass (M(n)) from 220 Da on day 1 of growth to 390 KDa and 690 Da on day 6; M(w) declined by about 35% from day 1 to day 3, the day of maximum pullulan titer. For the other strains, the ranges of molar mass on the day of maximum pullulan titer were 338-614 KDa (M(w)) and 100-6820 Da (M(n)).

Time-response of cultured deep-sea benthic foraminifera to different algal diets

NASA Astrophysics Data System (ADS)

Heinz, P.; Hemleben, Ch; Kitazato, H.

2002-03-01

The vertical distribution of benthic foraminifera in the surface sediment is influenced by environmental factors, mainly by food and oxygen supply. An experiment of three different time series was performed to investigate the response of deep-sea benthic foraminifera to simulated phytodetritus pulses under stable oxygen concentrations. Each series was fed constantly with one distinct algal species in equivalent amounts. The temporal reactions of the benthic foraminifera with regard to the vertical distribution in the sediment, the total number, and the species composition were observed and compared within the three series. Additionally, oxygen contents and bacterial cell numbers were measured to ensure that these factors were invariable and did not influence foraminiferal communities. The addition of algae leads to higher population densities 21 days after food was added. Higher numbers of individuals were probably caused by higher organic levels, which in turn induced reproduction. A stronger response is found after feeding with Amphiprora sp. and Pyramimonas sp., compared to Dunaliella tertiolecta. At a constant high oxygen supply, no migration to upper layers was observed after food addition, and more individuals were found in deeper layers. The laboratory results thus agree with the predictions of the TROX-model. An epifaunal microhabitat preference was shown for Adercotryma glomerata. Hippocrepina sp. was spread over the entire sediment depth with a shallow infaunal maximum. Melonis barleeanum preferred a deeper infaunal habitat. Bacterial cell concentrations were stable during the laboratory experiments and showed no significant response to higher organic fluxes.

The origin, historical variations, and distribution of heavy metals in the Qiongzhou Strait and nearby marine areas

NASA Astrophysics Data System (ADS)

Zhang, Zhiqiang; Chen, Liang; Wang, Weiping; Li, Tuanjie; Zu, Tingting

2017-04-01

We analyzed heavy metal concentrations in a number of surface sediments and cores from the Qiongzhou Strait and surrounding marine areas. The areas of high concentrations are primarily outside the eastern mouth of the Qiongzhou Strait and on the west side of the Leizhou Peninsula, whereas the areas of low concentrations are located primarily in the eastern Qiongzhou Strait. The maximum Cd, Pb and Zn concentrations in the samples collected in our study do not exceed the official standards for marine sediments, whereas the concentrations of Cr and Cu slightly exceed the standards. Correlations exist between the concentrations of Cu, Pb, Zn, Cr and Cd, and the concentrations of these metals are positively correlated with the mean particle size (φ value), indicating that the finer sediments have adsorbed greater amounts of heavy metal elements than the coarser sediments. An evaluation of the potential environmental risks demonstrates that certain indices of heavy metal pollution and environmental risks are relatively low and may be assigned low risk levels, thereby indicating that, in terms of heavy metals, the marine sedimentary environment in this region is only mildly impacted. Our analysis of the contaminant origins shows that the heavy metals in this region primarily originate in the Pearl River Estuary and that a small amount of them is derived from local runoff. The elevated heavy metal concentrations from the upper sections of the cores started 130 years ago, which indicats that heavy metals in the surface sediments are primarily due to human activities associated with industrialization.

Wind effects on coastal zone color scanner chlorophyll patterns in the U.S. Mid-Atlantic Bight during spring 1979

NASA Technical Reports Server (NTRS)

Eslinger, David L.; Iverson, Richard L.

1986-01-01

Coastal zone color scanner (CZCS) chlorophyll concentration increases in the Mid-Atlantic Bight were associated with high wind speeds in continental shelf waters during March and May 1979. Maximum spring CZCS chlorophyll concentrations occurred during April when the water column was not thermally stratified and were spatially and temporally associated with reductions in wind speed both in onshelf and in offshelf regions. Increased chlorophyll concentrations in offshelf waters were associated with high wind speeds during May when a deep chlorophyll maximum was present. Chlorophyll patchiness was observed on length scales typical of those controlled by biological processes during the April low-wind period but not during March or May when wind speeds were greater. The spring CZCS chlorophyll maximum in the southern portion of the Mid-Atlantic Bight occurred in response to a reduction in mixed layer depth caused by decreased wind speeds and not by increased water column stratification.

Ground-water quality for Grainger County, Tennessee

USGS Publications Warehouse

Weaver, J.D.; Patel, A.R.; Hickey, A.C.

1994-01-01

The residents of Grainger County depend on ground water for many of their daily needs including personal consumption and crop irrigation. To address concerns associated with ground-water quality related to domestic use, the U.S. Geological Survey collected water samples from 35 wells throughout the county during the summer 1992. The water samples were analyzed to determine if pesticides, nutrients, bacteria, and other selected constituents were present in the ground water. Wells selected for the study were between 100 and 250 feet deep and yielded 10 to 50 gallons of water per minute. Laboratory analyses of the water found no organic pesticides at concentrations exceeding the primary maximum contaminant levels established by the State of Tennessee for wells used for public supply. However, fecal coliform bacteria were detected at concentrations exceeding the State's maximum contaminant level in water from 15 of the 35 wells sampled. Analyses also indicated several inorganic compounds were present in the water samples at concentrations exceeding the secondary maximum contaminant level.

ICP-MS based methods to characterize nanoparticles of TiO2 and ZnO in sunscreens with focus on regulatory and safety issues.

PubMed

Bocca, Beatrice; Caimi, Stefano; Senofonte, Oreste; Alimonti, Alessandro; Petrucci, Francesco

2018-07-15

This study sought to develop analytical methods to characterize titanium dioxide (TiO 2 ) and zinc oxide (ZnO) nanoparticles (NPs), including the particle size distribution and concentration, in cream and spray sunscreens with different sun protection factor (SPF). The Single Particle Inductively Coupled Plasma-Mass Spectrometry (SP ICP-MS) was used as screening and fast method to determine particles size and number. The Asymmetric Flow-Field Flow Fractionation (AF4-FFF) as a pre-separation technique was on-line coupled to the Multi-Angle Light Scattering (MALS) and ICP-MS to determine particle size distributions and size dependent multi-elemental concentration. Both methods were optimized in sunscreens in terms of recovery, repeatability, limit of detection and linear dynamic range. Results showed that sunscreens contained TiO 2 particles with an average size of ≤107 nm and also a minor number of ZnO particles sized ≤98 nm. The higher fraction of particles <100 nm was observed in sunscreens with SPF 50+ (ca. 80%); the lower percentage (12-35%) in sunscreens with lower SPF values. Also the higher TiO 2 (up to 24% weight) and ZnO (ca. 0.25% weight) concentrations were found in formulations of SPF 50+. Creamy sunscreens could be considered safe containing TiO 2 and ZnO NPs less than the maximum allowable concentration of 25% weight as set by the European legislation. On the contrary, spray products required additional considerations with regard to the potential inhalation of NPs. The developed methods can contribute to the actual demand for regulatory control and safety assessment of metallic NPs in consumers' products. Copyright © 2018 Elsevier B.V. All rights reserved.

EXPERIMENTAL SUBSTANTIATION OF PERMEABILIZED HEPATOCYTES MODEL FOR INVESTIGATION OF MITOCHONDRIA IN SITU RESPIRATION.

PubMed

Merlavsky, V M; Manko, B O; Ikkert, O V; Manko, V V

2015-01-01

To verify experimentally the model of permeabilized hepatocytes, the degree of cell permeability was assessed using trypan blue and polarographycally determined cell respiration rate upon succinate (0.35 mM) and a-ketoglutarate (1 mM) oxidation. Oxidative phosphorylation was stimulated by ADP (750 μM). Hepatocyte permeabilization depends on digitonin concentraion in medium and on the number of cells in suspension. Thus, the permeabilization of 0.9-1.7 million cells/ml was completed by 25 μg/ml of digitonin, permeabilization of 2.0-3.0 million cells/ml--by 50 μg/ml of digitonin and permeabilization of 4.0-5.6 million cells/ml--by 100 μg/ml. Thus, the higher is the suspension density, the higher digitonin concentration is required. Treatment of hepatocytes with digitonin resulted in a decrease of endogenous respiration rate to a minimum upon 20-22 μg of digitonin per 1 million cells. Supplementation of permeabilized hepatocytes with α-ketoglutarate maintained stable respiration rate, on the level higher than endogenous respiration at the corresponding digitonin concentration, unlike the intact cells. Respiration rate of permeabilized hepatocytes at the simultaneous addition of α-ketoglutarate and ADP increased to the level of intact cell respiration, irrespective of digitonin concentration. Addition of solely succinate and especially succinate plus ADP markedly intensified the respiration of permeabilized hepatocytes to the level higher than that of intact cells. The dependence of succinate-stimulated respiration on digitonin concentration reached maximum at 20-22 αg of digitonin per 1 million cells. Optimal ratio of digitonin amount and the cell number in suspension is expected to be different in various tissues.

Factors influencing palmitoyl-CoA oxidation by rat liver peroxisomal fractions. Substrate concentration, organelle integrity and ATP.

PubMed Central

Thomas, J; Debeer, L J; De Schepper, P J; Mannaerts, G P

1980-01-01

1. The first dehydrogenation step of peroxisomal beta-oxidation involves the reduction of O2 to H2O2. Production rates of H2O2 and acetyl units by purified rat liver peroxisomes oxidizing palmitoyl-CoA were equal, indicating that H2O2 production is a reliable index for the release of acetyl units during peroxisomal fatty-acid oxidation. 2. Measurements of H2O2 and acid-soluble oxidation products during [1-14C]palmitoyl-CoA oxidation by purified peroxisomes revealed that the number of acetyl units released per molecule of palmitoyl-CoA oxidized rapidly decreased with increasing unbound palmitoyl-CoA concentrations. Structural damage to the peroxisomes caused by detergents or other treatments also decreased the number of acetyl units released. Under conditions where oxidation proceeded linearly with time the theoretical maximum of 5 acetyl units released per molecule of palmitoyl-CoA oxidized [Lazarow (1978) J. Biol. Chem. 253, 1522--1528] was never reached. 3. Expressed in terms of acetyl units produced and measured at low unbound-palmitoyl-CoA concentrations, mitochondrial oxidation was 10--20-fold higher than peroxisomal oxidation. 4. ATP stimulated peroxisomal palmitoyl-CoA oxidation approx. 2-fold. The ATP effect required the presence of Mg2+ and was lost when peroxisomal membranes were disrupted by Triton X-100 or high concentrations of unbound palmitoyl-CoA. 5. Disruption of peroxisomes by detergents, freeze--thawing, osmotic or mechanical treatment did not stimulate palmitoyl-CoA oxidation in the presence of ATP, indicating that peroxisomal fatty-acid-CoA oxidation was not latent. In the absence of ATP, Triton X-100 stimulated peroxisomal palmitoyl-CoA oxidation approx. 2-fold. PMID:7470063

Estimated plasma bupivacaine concentration after single dose and eight-hour continuous intra-articular infusion of bupivacaine in normal dogs.

PubMed

Bubenik, Loretta; Hosgood, Giselle; Barker, Steven; Hicks, Merrin; Serra, Verna; Stout, Rhett

2007-12-01

To estimate maximum plasma concentration (C(max)) and time to maximum plasma (t(max)) bupivacaine concentration after intra-articular administration of bupivacaine for single injection (SI) and injection followed by continuous infusion (CI) in normal dogs. Cross-over design with a 2-week washout period. Healthy Coon Hound dogs (n=8). Using gas chromatography/mass spectrometry, canine plasma bupivacaine concentration was measured before and after SI (1.5 mg/kg) and CI (1.5 mg/kg and 0.3 mg/kg/h). Software was used to establish plasma concentration-time curves and estimate C(max), T(max) and other pharmacokinetic variables for comparison of SI and CI. Bupivacaine plasma concentration after SI and CI best fit a 3 exponential model. For SI, mean maximum concentration (C(max), 1.33+/-0.954 microg/mL) occurred at 11.37+/-4.546 minutes. For CI, mean C(max) (1.13+/-0.509 microg/mL) occurred at 10.37+/-4.109 minutes. The area under the concentration-time curve was smaller for SI (143.59+/-118.390 microg/mL x min) than for CI (626.502+/-423.653 microg/mL x min, P=.02) and half-life was shorter for SI (61.33+/-77.706 minutes) than for CI (245.363+/-104.415 minutes, P=.01). The highest plasma bupivacaine concentration for any dog was 3.2 microg/mL for SI and 2.3 microg/mL for CI. Intra-articular bupivacaine administration results in delayed absorption from the stifle into the systemic circulation with mean C(max) below that considered toxic and no systemic drug accumulation. Intra-articular bupivacaine can be administered with small risk of reaching toxic plasma concentrations in dogs, though toxic concentrations may be approached. Caution should be exercised with multimodal bupivacaine administration because plasma drug concentration may rise higher than with single intra-articular injection.

Fresnel cup reflector directs maximum energy from light source

NASA Technical Reports Server (NTRS)

Laue, E. G.; Youngberg, C. L.

1964-01-01

To minimize shielding and overheating, a composite Fresnel cup reflector design directs the maximum energy from a light source. It consists of a uniformly ellipsoidal end surface and an extension comprising a series of confocal ellipsoidal and concentric spherical surfaces.

Generic Schemes for Single-Molecule Kinetics. 2: Information Content of the Poisson Indicator.

PubMed

Avila, Thomas R; Piephoff, D Evan; Cao, Jianshu

2017-08-24

Recently, we described a pathway analysis technique (paper 1) for analyzing generic schemes for single-molecule kinetics based upon the first-passage time distribution. Here, we employ this method to derive expressions for the Poisson indicator, a normalized measure of stochastic variation (essentially equivalent to the Fano factor and Mandel's Q parameter), for various renewal (i.e., memoryless) enzymatic reactions. We examine its dependence on substrate concentration, without assuming all steps follow Poissonian kinetics. Based upon fitting to the functional forms of the first two waiting time moments, we show that, to second order, the non-Poissonian kinetics are generally underdetermined but can be specified in certain scenarios. For an enzymatic reaction with an arbitrary intermediate topology, we identify a generic minimum of the Poisson indicator as a function of substrate concentration, which can be used to tune substrate concentration to the stochastic fluctuations and to estimate the largest number of underlying consecutive links in a turnover cycle. We identify a local maximum of the Poisson indicator (with respect to substrate concentration) for a renewal process as a signature of competitive binding, either between a substrate and an inhibitor or between multiple substrates. Our analysis explores the rich connections between Poisson indicator measurements and microscopic kinetic mechanisms.

Electrochemical removal of phenol from oil refinery wastewater.

PubMed

Abdelwahab, O; Amin, N K; El-Ashtoukhy, E-S Z

2009-04-30

This study explores the possibility of using electrocoagulation to remove phenol from oil refinery waste effluent using a cell with horizontally oriented aluminum cathode and a horizontal aluminum screen anode. The removal of phenol was investigated in terms of various parameters namely: pH, operating time, current density, initial phenol concentration and addition of NaCl. Removal of phenol during electrocoagulation was due to combined effect of sweep coagulation and adsorption. The results showed that, at high current density and solution pH 7, remarkable removal of 97% of phenol after 2h can be achieved. The rate of electrocoagulation was observed to increase as the phenol concentration decreases; the maximum removal rate was attained at 30 mg L(-1) phenol concentration. For a given current density using an array of closely packed Al screens as anode was found to be more effective than single screen anode, the percentage phenol removal was found to increase with increasing the number of screens per array. After 2h of electrocoagulation, 94.5% of initial phenol concentration was removed from the petroleum refinery wastewater. Energy consumption and aluminum Electrode consumption were calculated per gram of phenol removed. The present study shows that, electrocoagulation of phenol using aluminum electrodes is a promising process.