All-optical lithography process for contacting nanometer precision donor devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ward, Daniel Robert; Marshall, Michael Thomas; Campbell, DeAnna Marie

In this article, we describe an all-optical lithography process that can make electrical contact to nanometer-precision donor devices fabricated in silicon using scanning tunneling microscopy (STM). This is accomplished by implementing a cleaning procedure in the STM that allows the integration of metal alignment marks and ion-implanted contacts at the wafer level. Low-temperature transport measurements of a patterned device establish the viability of the process.

Clean focus, dose and CD metrology for CD uniformity improvement

NASA Astrophysics Data System (ADS)

Lee, Honggoo; Han, Sangjun; Hong, Minhyung; Kim, Seungyoung; Lee, Jieun; Lee, DongYoung; Oh, Eungryong; Choi, Ahlin; Kim, Nakyoon; Robinson, John C.; Mengel, Markus; Pablo, Rovira; Yoo, Sungchul; Getin, Raphael; Choi, Dongsub; Jeon, Sanghuck

2018-03-01

Lithography process control solutions require more exacting capabilities as the semiconductor industry goes forward to the 1x nm node DRAM device manufacturing. In order to continue scaling down the device feature sizes, critical dimension (CD) uniformity requires continuous improvement to meet the required CD error budget. In this study we investigate using optical measurement technology to improve over CD-SEM methods in focus, dose, and CD. One of the key challenges is measuring scanner focus of device patterns. There are focus measurement methods based on specially designed marks on scribe-line, however, one issue of this approach is that it will report focus of scribe line which is potentially different from that of the real device pattern. In addition, scribe-line marks require additional design and troubleshooting steps that add complexity. In this study, we investigated focus measurement directly on the device pattern. Dose control is typically based on using the linear correlation behavior between dose and CD. The noise of CD measurement, based on CD-SEM for example, will not only impact the accuracy, but also will make it difficult to monitor dose signature on product wafers. In this study we will report the direct dose metrology result using an optical metrology system which especially enhances the DUV spectral coverage to improve the signal to noise ratio. CD-SEM is often used to measure CD after the lithography step. This measurement approach has the advantage of easy recipe setup as well as the flexibility to measure critical feature dimensions, however, we observe that CD-SEM metrology has limitations. In this study, we demonstrate within-field CD uniformity improvement through the extraction of clean scanner slit and scan CD behavior by using optical metrology.

21 CFR 801.45 - Devices that must be directly marked with a unique device identifier.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Devices that must be directly marked with a unique device identifier. 801.45 Section 801.45 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF... previously marked under paragraph (a) of this section. (e) Exception to be noted in design history file. A...

PillCam(TradeMark), a Noninvasive Endoscopic Device for the Measurement of Gastrointestinal Motility Changes

NASA Technical Reports Server (NTRS)

Vaksman, Zahman; Crady, Camille; Raju, G. S.; Putcha, Lakshmi

2007-01-01

Introduction: Bioavailability and effectiveness of drugs given by mouth are governed in part by gastrointestinal (GI) motility and function. Microgravity has been shown to decrease GI motility as indicated by a 3 fold increase in gastrointestinal transit time (GITT). The PillCam(TradeMark), an endoscopic camera embedded in a capsule, is a novel noninvasive and unobtrusive device that is used for the diagnosis of GI pathology. The purpose of this study is to evaluate the usefulness of PillCam(TradeMark) as an alternative to the Lactulose Breath Hydrogen Test (LBHT) for estimating GI motility. The sensitivity and applicability of this device for detection and estimation of the effect of promethazine, a deterrent, and caffeine, a prokinetic, on GI motility were also examined. Method: In this semi-randomized cross-over design study, six male and six female subjects were administered the following 4 treatments: PillCam(TradeMark) alone, PillCam(TradeMark)+Lactulose (10g), PillCam(TradeMark)+caffeine (200mg), and PillCam(TradeMark)+Promethazine (50mg). Results: GITT ranged between 1:24 and 7:52 hr:min. Lactulose did not alter GITT. A significant increase in GITT was noticed after administration of PMZ when compared to values from PillCam(TradeMark) treatment alone or PillCam(TradeMark)+Lactulose treatment. No difference in GITT after caffeine treatment was noticed. While there were no gender related differences in GITT after administration of PillCam(TradeMark) or with lactulose, a significant difference (p<.05) between genders was observed after promethazine administration with mean GITT higher in males (5:50 hr:min) than females (4:15 hr:min). Conclusion: The PillCam(TradeMark) capsule is applicable for the determination of GITT using time stamped GI images. It can be successfully used for the assessment of drug induced changes in GI motility and therefore, may be applicable for microgravity and analog environment studies on GI motility and function.

Pressure beneath the Surface of a Fluid: Measuring the Correct Depth

ERIC Educational Resources Information Center

McCall, Richard P.

2013-01-01

Systematic errors can cause measurements to deviate from the actual value of the quantity being measured. Faulty equipment (such as a meterstick that is not marked correctly), inaccurate calibration of measuring devices (such as a scale to measure mass that has not been properly zeroed), and improper use of equipment by the experimenter (such as…

50 CFR 260.7 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2010 CFR

2010-10-01

..., memoranda, marks, other identifications, and devices for purposes of the Agricultural Marketing Act. 260.7..., marks, other identifications, and devices for purposes of the Agricultural Marketing Act. Subsection 203(h) of the Agricultural Marketing Act of 1946 provides criminal penalties for various specified...

The Mark 3 Haploscope

NASA Technical Reports Server (NTRS)

Decker, T. A.; Williams, R. E.; Kuether, C. L.; Logar, N. D.; Wyman-Cornsweet, D.

1975-01-01

A computer-operated binocular vision testing device was developed as one part of a system designed for NASA to evaluate the visual function of astronauts during spaceflight. This particular device, called the Mark 3 Haploscope, employs semi-automated psychophysical test procedures to measure visual acuity, stereopsis, phoria, fixation disparity, refractive state and accommodation/convergence relationships. Test procedures are self-administered and can be used repeatedly without subject memorization. The Haploscope was designed as one module of the complete NASA Vision Testing System. However, it is capable of stand-alone operation. Moreover, the compactness and portability of the Haploscope make possible its use in a broad variety of testing environments.

9 CFR 316.1 - Authorization required to make devices bearing official marks.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Authorization required to make devices bearing official marks. 316.1 Section 316.1 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE... required to make devices bearing official marks. No brand manufacturer, printer or other person shall cast...

9 CFR 317.3 - Approval of abbreviations of marks of inspection; preparation of marking devices bearing...

Code of Federal Regulations, 2011 CFR

2011-01-01

... marking device containing any official mark or simulation thereof, or any label bearing any such mark or simulation, without the written authority therefor of the Administrator. However, when any such sample label... inspection legend, or simulation thereof, shown in § 312.2(a), § 312.3(a) (only the legend appropriate for...

9 CFR 317.3 - Approval of abbreviations of marks of inspection; preparation of marking devices bearing...

Code of Federal Regulations, 2013 CFR

2013-01-01

... marking device containing any official mark or simulation thereof, or any label bearing any such mark or simulation, without the written authority therefor of the Administrator. However, when any such sample label... inspection legend, or simulation thereof, shown in § 312.2(a), § 312.3(a) (only the legend appropriate for...

9 CFR 317.3 - Approval of abbreviations of marks of inspection; preparation of marking devices bearing...

Code of Federal Regulations, 2014 CFR

2014-01-01

... marking device containing any official mark or simulation thereof, or any label bearing any such mark or simulation, without the written authority therefor of the Administrator. However, when any such sample label... inspection legend, or simulation thereof, shown in § 312.2(a), § 312.3(a) (only the legend appropriate for...

9 CFR 317.3 - Approval of abbreviations of marks of inspection; preparation of marking devices bearing...

Code of Federal Regulations, 2010 CFR

2010-01-01

... marking device containing any official mark or simulation thereof, or any label bearing any such mark or simulation, without the written authority therefor of the Administrator. However, when any such sample label... inspection legend, or simulation thereof, shown in § 312.2(a), § 312.3(a) (only the legend appropriate for...

9 CFR 317.3 - Approval of abbreviations of marks of inspection; preparation of marking devices bearing...

Code of Federal Regulations, 2012 CFR

2012-01-01

... marking device containing any official mark or simulation thereof, or any label bearing any such mark or simulation, without the written authority therefor of the Administrator. However, when any such sample label... inspection legend, or simulation thereof, shown in § 312.2(a), § 312.3(a) (only the legend appropriate for...

Refrigeration system oil measurement and sampling device

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baker, J.A.

1989-09-19

This patent describes a sampling device for use with a refrigeration system having a refrigerant and oil entrained therein. It comprises: an elongated reservoir having a stepped bore therein for receiving refrigerant and oil carried thereby. The reservoir comprising a large bore diameter upper section having an index marking the fill level of the reservoir and a small bore diameter lower section having graduation marks for oil level measurement. The upper and lower sections comprising transparent material to allow observation of the contents, first valve means for coupling the reservoir to the refrigeration system to admit liquid refrigerant to themore » reservoir, second valve means for selectively coupling the reservoir to the low pressure side of the refrigeration system or to a vacuum line to evacuate vaporized refrigerant from the reservoir, and means for supplying heat to the refrigerant in the bore to facilitate vaporization of the refrigerant.« less

New overlay measurement technique with an i-line stepper using embedded standard field image alignment marks for wafer bonding applications

NASA Astrophysics Data System (ADS)

Kulse, P.; Sasai, K.; Schulz, K.; Wietstruck, M.

2017-06-01

In the last decades the semiconductor technology has been driven by Moore's law leading to high performance CMOS technologies with feature sizes of less than 10 nm [1]. It has been pointed out that not only scaling but also the integration of novel components and technology modules into CMOS/BiCMOS technologies is becoming more attractive to realize smart and miniaturized systems [2]. Driven by new applications in the area of communication, health and automation, new components and technology modules such as BiCMOS embedded RF-MEMS, high-Q passives, Sibased microfluidics and InP-SiGe BiCMOS heterointegration have been demonstrated [3-6]. In contrast to standard VLSI processes fabricated on front side of the silicon wafer, these new technology modules require addition backside processing of the wafer; thus an accurate alignment between the front and backside of the wafer is mandatory. In previous work an advanced back to front side alignment technique and implementation into IHP's 0.25/0.13 μm high performance SiGe:C BiCMOS backside process module has been presented [7]. The developed technique enables a high resolution and accurate lithography on the backside of BiCMOS wafer for additional backside processing. In addition to the aforementioned back side process technologies, new applications like Through-Silicon Vias (TSV) for interposers and advanced substrate technologies for 3D heterogeneous integration demand not only single wafer fabrication but also processing of wafer stacks provided by temporary and permanent wafer bonding [8]. Therefore, the available overlay measurement techniques are not suitable if overlay and alignment marks are realized at the bonding interface of a wafer stack which consists of both a silicon device and a silicon carrier wafer. The former used EVG 40NT automated overlay measurement system, which use two opposite positioned microscopes inspecting simultaneous the wafer back and front side, is not capable measuring embedded overlay marks. In this work, the non-contact infrared alignment system of the Nikon i-line Stepper NSR-SF150 for both the alignment and the overlay determination of bonded wafer stacks with embedded alignment marks are used to achieve an accurate alignment between the different wafer sides. The embedded field image alignment (FIA) marks of the interface and the device wafer top layer are measured in a single measurement job. By taking the offsets between all different FIA's into account, after correcting the wafer rotation induced FIA position errors, hence an overlay for the stacked wafers can be determined. The developed approach has been validated by a standard back to front side application. The overlay was measured and determined using both, the EVG NT40 automated measurement system with special overlay marks and the measurement of the FIA marks of the front and back side layer. A comparison of both results shows mismatches in x and y translations smaller than 200 nm, which is relatively small compared to the overlay tolerances of +/-500 nm for the back to front side process. After the successful validation of the developed technique, special wafer stacks with FIA alignment marks in the bonding interface are fabricated. Due to the super IR light transparency of both doubled side polished wafers, the embedded FIA marks generate a stable and clear signal for accurate x and y wafer coordinate positioning. The FIA marks of the device wafer top layer were measured under standard condition in a developed photoresist mask without IR illumination. Following overlay calculation shows an overlay of less than 200 nm, which enables very accurate process condition for highly scaled TSV integration and advanced substrate integration into IHP's 0.25/0.13 μm SiGe:C BiCMOS technology. The presented method can be applied for both the standard back to front side process technologies and also new temporary and permanent wafer bonding applications.

9 CFR 381.131 - Preparation of labeling or other devices bearing official inspection marks without advance...

Code of Federal Regulations, 2011 CFR

2011-01-01

... otherwise make any marking device containing any official mark or simulation thereof, or any label bearing any such mark or simulation, without the written authority therefor of the Administrator. However... legend shown in Figure 5 of § 381.102 or any simulation of that legend. (1) The certificate is a Food...

9 CFR 381.131 - Preparation of labeling or other devices bearing official inspection marks without advance...

Code of Federal Regulations, 2010 CFR

2010-01-01

... otherwise make any marking device containing any official mark or simulation thereof, or any label bearing any such mark or simulation, without the written authority therefor of the Administrator. However... legend shown in Figure 5 of § 381.102 or any simulation of that legend. (1) The certificate is a Food...

9 CFR 381.131 - Preparation of labeling or other devices bearing official inspection marks without advance...

Code of Federal Regulations, 2012 CFR

2012-01-01

... otherwise make any marking device containing any official mark or simulation thereof, or any label bearing any such mark or simulation, without the written authority therefor of the Administrator. However... legend shown in Figure 5 of § 381.102 or any simulation of that legend. (1) The certificate is a Food...

9 CFR 381.131 - Preparation of labeling or other devices bearing official inspection marks without advance...

Code of Federal Regulations, 2013 CFR

2013-01-01

... otherwise make any marking device containing any official mark or simulation thereof, or any label bearing any such mark or simulation, without the written authority therefor of the Administrator. However... legend shown in Figure 5 of § 381.102 or any simulation of that legend. (1) The certificate is a Food...

9 CFR 381.131 - Preparation of labeling or other devices bearing official inspection marks without advance...

Code of Federal Regulations, 2014 CFR

2014-01-01

... otherwise make any marking device containing any official mark or simulation thereof, or any label bearing any such mark or simulation, without the written authority therefor of the Administrator. However... legend shown in Figure 5 of § 381.102 or any simulation of that legend. (1) The certificate is a Food...

Performance comparison for Barnes model 12-1000, Exotech model 100, and Ideas Inc. Biometer Mark 2

NASA Technical Reports Server (NTRS)

Robinson, B. (Principal Investigator)

1981-01-01

Results of tests show that all channels of all instruments, except channel 3 of the Biometer Mark 2, were stable in response to input signals were linear, and were adequately stable in response to temperature changes. The Biometer Mark 2 is labelled with an inappropriate description of the units measured and the dynamic range is a inappropriate for field measurements causing unnecessarily high fractional errors. This instrument is, therefore, quantization limited. The dynamic range and noise performance of the Model 12-1000 are appropriate for remote sensing field research. The field of view and performance of the Model 100A and the Model 12-1000 are satisfactory. The Biometer Mark 2 has not, as yet, been satisfactorily equipped with an acceptable field of view determining device. Neither the widely used aperture plate nor the 24 deg cone are acceptable.

Specifying Skill-Based Training Strategies and Devices: A Model Description

DTIC Science & Technology

1990-06-01

Technical Report 897 Specifying Skill-Based Training N Strategies and Devices: A Model Description I Paui J. Sticha and Mark Schlager Human Resources...unlimied 90 ’ Technical Report 897 Specifying Skill-Based Training Strategies and Devices: A Model Description Paul J. Sticha and Mark Schlager Human...SECURITY CLASSIFICATION OF THIS PAGE Form Approved REPORT DOCUMENTATION PAGE FMNo o7 ote la. REPORT SECURITY CLASSIFICATION lb. RESTRICTWE MARKINGS

Real cell overlay measurement through design based metrology

NASA Astrophysics Data System (ADS)

Yoo, Gyun; Kim, Jungchan; Park, Chanha; Lee, Taehyeong; Ji, Sunkeun; Jo, Gyoyeon; Yang, Hyunjo; Yim, Donggyu; Yamamoto, Masahiro; Maruyama, Kotaro; Park, Byungjun

2014-04-01

Until recent device nodes, lithography has been struggling to improve its resolution limit. Even though next generation lithography technology is now facing various difficulties, several innovative resolution enhancement technologies, based on 193nm wavelength, were introduced and implemented to keep the trend of device scaling. Scanner makers keep developing state-of-the-art exposure system which guarantees higher productivity and meets a more aggressive overlay specification. "The scaling reduction of the overlay error has been a simple matter of the capability of exposure tools. However, it is clear that the scanner contributions may no longer be the majority component in total overlay performance. The ability to control correctable overlay components is paramount to achieve the desired performance.(2)" In a manufacturing fab, the overlay error, determined by a conventional overlay measurement: by using an overlay mark based on IBO and DBO, often does not represent the physical placement error in the cell area of a memory device. The mismatch may arise from the size or pitch difference between the overlay mark and the cell pattern. Pattern distortion, caused by etching or CMP, also can be a source of the mismatch. Therefore, the requirement of a direct overlay measurement in the cell pattern gradually increases in the manufacturing field, and also in the development level. In order to overcome the mismatch between conventional overlay measurement and the real placement error of layer to layer in the cell area of a memory device, we suggest an alternative overlay measurement method utilizing by design, based metrology tool. A basic concept of this method is shown in figure1. A CD-SEM measurement of the overlay error between layer 1 and 2 could be the ideal method but it takes too long time to extract a lot of data from wafer level. An E-beam based DBM tool provides high speed to cover the whole wafer with high repeatability. It is enabled by using the design as a reference for overlay measurement and a high speed scan system. In this paper, we have demonstrated that direct overlay measurement in the cell area can distinguish the mismatch exactly, instead of using overlay mark. This experiment was carried out for several critical layer in DRAM and Flash memory, using DBM(Design Based Metrology) tool, NGR2170™.

Optical system for object detection and delineation in space

NASA Astrophysics Data System (ADS)

Handelman, Amir; Shwartz, Shoam; Donitza, Liad; Chaplanov, Loran

2018-01-01

Object recognition and delineation is an important task in many environments, such as in crime scenes and operating rooms. Marking evidence or surgical tools and attracting the attention of the surrounding staff to the marked objects can affect people's lives. We present an optical system comprising a camera, computer, and small laser projector that can detect and delineate objects in the environment. To prove the optical system's concept, we show that it can operate in a hypothetical crime scene in which a pistol is present and automatically recognize and segment it by various computer-vision algorithms. Based on such segmentation, the laser projector illuminates the actual boundaries of the pistol and thus allows the persons in the scene to comfortably locate and measure the pistol without holding any intermediator device, such as an augmented reality handheld device, glasses, or screens. Using additional optical devices, such as diffraction grating and a cylinder lens, the pistol size can be estimated. The exact location of the pistol in space remains static, even after its removal. Our optical system can be fixed or dynamically moved, making it suitable for various applications that require marking of objects in space.

Coma measurement by transmission image sensor with a PSM

NASA Astrophysics Data System (ADS)

Wang, Fan; Wang, Xiangzhao; Ma, Mingying; Zhang, Dongqing; Shi, Weijie; Hu, Jianming

2005-01-01

As feature size decreases, especially with the use of resolution enhancement technique such as off axis illumination and phase shifting mask, fast and accurate in-situ measurement of coma has become very important in improving the performance of modern lithographic tools. The measurement of coma can be achieved by the transmission image sensor, which is an aerial image measurement device. The coma can be determined by measuring the positions of the aerial image at multiple illumination settings. In the present paper, we improve the measurement accuracy of the above technique with an alternating phase shifting mask. Using the scalar diffraction theory, we analyze the effect of coma on the aerial image. To analyze the effect of the alternating phase shifting mask, we compare the pupil filling of the mark used in the above technique with that of the phase-shifted mark used in the new technique. We calculate the coma-induced image displacements of the marks at multiple partial coherence and NA settings, using the PROLITH simulation program. The simulation results show that the accuracy of coma measurement can increase approximately 20 percent using the alternating phase shifting mask.

Enhacement of intrafield overlay using a design based metrology system

NASA Astrophysics Data System (ADS)

Jo, Gyoyeon; Ji, Sunkeun; Kim, Shinyoung; Kang, Hyunwoo; Park, Minwoo; Kim, Sangwoo; Kim, Jungchan; Park, Chanha; Yang, Hyunjo; Maruyama, Kotaro; Park, Byungjun

2016-03-01

As the scales of the semiconductor devices continue to shrink, accurate measurement and control of the overlay have been emphasized for securing more overlay margin. Conventional overlay analysis methods are based on the optical measurement of the overlay mark. However, the overlay data obtained from these optical methods cannot represent the exact misregistration between two layers at the circuit level. The overlay mismatch may arise from the size or pitch difference between the overlay mark and the real pattern. Pattern distortion, caused by CMP or etching, could be a source of the overlay mismatch as well. Another issue is the overlay variation in the real circuit pattern which varies depending on its location. The optical overlay measurement methods, such as IBO and DBO that use overlay mark on the scribeline, are not capable of defining the exact overlay values of the real circuit. Therefore, the overlay values of the real circuit need to be extracted to integrate the semiconductor device properly. The circuit level overlay measurement using CDSEM is time-consuming in extracting enough data to indicate overall trend of the chip. However DBM tool is able to derive sufficient data to display overlay tendency of the real circuit region with high repeatability. An E-beam based DBM(Design Based Metrology) tool can be an alternative overlay measurement method. In this paper, we are going to certify that the overlay values extracted from optical measurement cannot represent the circuit level overlay values. We will also demonstrate the possibility to correct misregistration between two layers using the overlay data obtained from the DBM system.

Characterization of a Low-Cost Multiparameter Sensor for Solar Resource Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Habte, Aron M; Sengupta, Manajit; Andreas, Afshin M

Low-cost, multiparameter sensing and measurement devices enable cost-effective monitoring of the functional, operational reliability, efficiency, and resiliency of the electric grid. The National Renewable Research Laboratory (NREL) Solar Radiation Research Laboratory (SRRL), in collaboration with Arable Labs, Inc., deployed Arable Lab's Mark multiparameter sensor system. The device measures the downwelling and upwelling shortwave solar resource and longwave radiation, humidity, air temperature, and ground temperature. The system is also equipped with six downward-and upward-facing narrowband spectrometer channels that measure spectral radiation and surface spectral reflectance. This study describes the shortwave calibration, characterization, and validation of measurement accuracy of this instrument bymore » comparison with existing instruments that are part of NREL-SRRL's Baseline Measurement System.« less

9 CFR 316.4 - Marking devices; to be furnished by official establishments; control of.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Marking devices; to be furnished by official establishments; control of. 316.4 Section 316.4 Animals and Animal Products FOOD SAFETY AND... seals, shall be used only under supervision of a Program employee, and, when not in use for marking...

9 CFR 316.4 - Marking devices; to be furnished by official establishments; control of.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Marking devices; to be furnished by official establishments; control of. 316.4 Section 316.4 Animals and Animal Products FOOD SAFETY AND... seals, shall be used only under supervision of a Program employee, and, when not in use for marking...

SU-F-T-496: An Investigation of Two Novel Devices for Testing Linac Clearance During CT Simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morrow, A; Massingill, B

Purpose: This work’s objective is to determine the efficacy of two newly patented devices termed the Mor-O rings, Mark1 and Mark2, developed to predict collisions between the patient and a linac at the time of CT simulation. Methods: Mark1: A ring with an inner radius equal to the distance between the isocenter and the nearest portion of a linac head(diso) was made. This is mounted to a stand that allows vertical repositioning. The ring is placed around the patient on the CT table and aligned with isocenter. The patient is moved through the ring. If the ring touches the patient,more » a collision is predicted. To test this device, predicted collisions were marked on a phantom. The phantom was then repositioned on the linac table where the collisions were verified. Mark2: An arc with the radius diso was created with a re-locatable half-linac head wire-frame. The Mark2 is positioned in the same way as the Mark1 but can additionally mimic couch and gantry angulations. The Mark2 was tested with a volunteer using multiple couch, gantry and isocenter positions. The volunteer was then repositioned on the linac table to verify the angles of collisions. Results: Mark1: One isocenter out of ten showed negative clearance (0.9mm) on the linac table. All other collisions were predicted with 1 to 36mm of additional clearance. Mark2: All collisions were prevented with an additional 1.3 to 14.8 degrees of clearance. Conclusion: The Mark1 prototype is able to predict all collisions when no couch angulation is used. This device takes less than a minute to setup and is simple to use. The Mark2, when testing beam geometries used for noncoplanar SBRT, was able to prevent all collisions with 1.3 to 14.8 degrees additional clearance. Improvements in construction for both devices could increase accuracy and usability. Andrew Morrow owns Morrow Physics, LLC and Brian Massingill owns Spur Physics, LLC. We are both listed on the patent for the devices investigated in this work (patent 9220922). Our current employer, Baylor Scott and White, is also on the patent.« less

Photogrammetry Tool for Forensic Analysis

NASA Technical Reports Server (NTRS)

Lane, John

2012-01-01

A system allows crime scene and accident scene investigators the ability to acquire visual scene data using cameras for processing at a later time. This system uses a COTS digital camera, a photogrammetry calibration cube, and 3D photogrammetry processing software. In a previous instrument developed by NASA, the laser scaling device made use of parallel laser beams to provide a photogrammetry solution in 2D. This device and associated software work well under certain conditions. In order to make use of a full 3D photogrammetry system, a different approach was needed. When using multiple cubes, whose locations relative to each other are unknown, a procedure that would merge the data from each cube would be as follows: 1. One marks a reference point on cube 1, then marks points on cube 2 as unknowns. This locates cube 2 in cube 1 s coordinate system. 2. One marks reference points on cube 2, then marks points on cube 1 as unknowns. This locates cube 1 in cube 2 s coordinate system. 3. This procedure is continued for all combinations of cubes. 4. The coordinate of all of the found coordinate systems is then merged into a single global coordinate system. In order to achieve maximum accuracy, measurements are done in one of two ways, depending on scale: when measuring the size of objects, the coordinate system corresponding to the nearest cube is used, or when measuring the location of objects relative to a global coordinate system, a merged coordinate system is used. Presently, traffic accident analysis is time-consuming and not very accurate. Using cubes with differential GPS would give absolute positions of cubes in the accident area, so that individual cubes would provide local photogrammetry calibration to objects near a cube.

Application of a liquid crystal spatial light modulator to laser marking.

PubMed

Parry, Jonathan P; Beck, Rainer J; Shephard, Jonathan D; Hand, Duncan P

2011-04-20

Laser marking is demonstrated using a nanosecond (ns) pulse duration laser in combination with a liquid crystal spatial light modulator to generate two-dimensional patterns directly onto thin films and bulk metal surfaces. Previous demonstrations of laser marking with such devices have been limited to low average power lasers. Application in the ns regime enables more complex, larger scale marks to be generated with more widely available and industrially proven laser systems. The dynamic nature of the device is utilized to improve mark quality by reducing the impact of the inherently speckled intensity distribution across the generated image and reduce thermal effects in the marked surface. © 2011 Optical Society of America

Thickness and marking quality of different occlusal contact registration strips

PubMed Central

TOLEDO, Maria Fernanda de Souza Mauá Serapião; JÓIAS, Renata Pilli; MARQUES-IASI, Yves Santini; NEVES, Ana Christina Claro; RODE, Sigmar de Mello

2014-01-01

Objectives Evaluate the thickness and the marking quality of different occlusal contact registration strips (OCRS) and a possible correlation between them. Material and Methods The following OCRS were selected: Accufilm II, BK20, BK21, BK22, BK23, BK28, and BK31. The thickness was measured in three points of the OCRS with an electronic measuring device (TESA), and the mean was calculated. To produce the marks on the strips, composite resin specimens were adapted to a universal testing machine (Versat 2000) with 40 kgf load cell at a speed of 1.0 mm/min. The mark images were photographed with a stereoscopic microscope (Stemi SV11) and processed and analyzed by the 550-Leica Qwin® analyzer. Results Values (μm) found in the 1st and 2nd thickness measurements were: Accufilm II - 16.4 and 14.2; BK20 - 10.0 and 8.1; BK21 - 9.5 and 8.0; BK22 - 9.7 and 8.7; BK23 - 9.8 and 7.9; BK28 - 12.8 and 10.0; and BK31 - 8.4 and 8.0, respectively. The mean (mm2) values found in the mark areas were: Accufilm II - 0.078; BK20 - 0.035; BK21 - 0.045; BK22 - 0.012; BK23 - 0.022; BK28 - 0.024; and BK31 - 0.024. The results were submitted to the Kruskal-Wallis (p<0.05) and Pearson’s correlation tests. Conclusions Only in the 2nd measurement, the OCRS thickness observed was similar to the value indicated by the manufacturers; the Accufilm II and the BK28 strips showed the better marks; and no correlation was found between the thickness and the marking area. PMID:25591020

An automated miniaturized Haploscope for testing binocular visual function

NASA Technical Reports Server (NTRS)

Decker, T. A.; Williams, R. E.; Kuether, C. L.; Wyman-Cornsweet, D.

1976-01-01

A computer-controlled binocular vision testing device has been developed as one part of a system designed for NASA to test the vision of astronauts during spaceflight. The device, called the Mark III Haploscope, utilizes semi-automated psychophysical test procedures to measure visual acuity, stereopsis, phorias, fixation disparity and accommodation/convergence relationships. All tests are self-administered, yield quantitative data and may be used repeatedly without subject memorization. Future applications of this programmable, compact device include its use as a clinical instrument to perform routine eye examinations or vision screening, and as a research tool to examine the effects of environment or work-cycle upon visual function.

Road Nail: Experimental Solar Powered Intelligent Road Marking System

NASA Astrophysics Data System (ADS)

Samardžija, Dragan; Teslić, Nikola; Todorović, Branislav M.; Kovač, Erne; Isailović, Đorđe; Miladinović, Bojan

2012-03-01

Driving in low visibility conditions (night time, fog or heavy precipitation) is particularly challenging task with an increased probability of traffic accidents and possible injuries. Road Nail is a solar powered intelligent road marking system of wirelessly networked signaling devices that improve driver safety in low visibility conditions along hazardous roadways. Nails or signaling devices are autonomous nodes with capability to accumulate energy, exchange wireless messages, detect approaching vehicles and emit signalization light. We have built an experimental test-bed that consists of 20 nodes and a cellular gateway. Implementation details of the above system, including extensive measurements and performance evaluations in realistic field deployments are presented. A novel distributed network topology discovery scheme is proposed which integrates both sensor and wireless communication aspects, where nodes act autonomously. Finally, integration of the Road Nail system with the cellular network and the Internet is described.

Contrasting clinical evidence for market authorisation of cardio-vascular devices in Europe and the USA: a systematic analysis of 10 devices based on Austrian pre-reimbursement assessments.

PubMed

Wild, Claudia; Erdös, Judit; Zechmeister, Ingrid

2014-11-04

European medical device regulation is under scrutiny and will be re-regulated with stricter rules concerning requirements for clinical evidence for high-risk medical devices. It is the aim of this study to analyse the differences between Europe and USA in dealing with risks and benefits of new cardio-vascular devices. Since no information is available on clinical data used by the Notified Body for CE-marking, data from Austrian pre-reimbursement assessments close to European market approval were used as proxy and compared with clinical data available at time of market approval by FDA in the USA. 10 cardio-vascular interventions with 27 newly CE approved medical devices were analysed. The time lag between market authorisation in Europe and in the USA is 3 to 7 years. Only 7 CE-marked devices also hold a FDA market approval, 7 further devices are in FDA approved ongoing efficacy trials. For 4 of the CE-marked devices the FDA market application or the approval-trial was either suspended due to efficacy or safety concerns or the approval was denied. Evidence available at time of CE-marking are most often case-series or small feasibility RCTs, while large RCTs and only in rare cases prospective cohort studies are the basis of FDA approvals. Additionally, the FDA often requires post-approval studies for high-risk devices. Market authorisation based on mature clinical data deriving from larger RCTs and longer follow-ups do not only change the perspective on the risk-benefit ratio, but also secures real patient benefit and safety and assures payers of investing only in truly innovative devices.

Spacelab

NASA Image and Video Library

1992-06-01

The first United States Microgravity Laboratory (USML-1) flew in orbit inside the Spacelab science module for extended periods, providing scientists and researchers greater opportunities for research in materials science, fluid dynamics, biotechnology (crystal growth), and combustion science. This photograph shows Astronaut Larry De Lucas wearing a stocking plethysmograph during the mission. Muscle size in the legs changes with exposure to microgravity. A stocking plethysmograph, a device for measuring the volume of a limb, was used to help determine these changes. Several times over the course of the mission, an astronaut will put on the plethysmograph, pull the tapes tight and mark them. By comparing the marks, changes in muscle volume can be measured. The USML-1 was launched aboard the Space Shuttle Orbiter Columbia (STS-50) on June 25, 1992.

Evaluation of the effects of school zone signs and markings on speed reduction: a driving simulator study.

PubMed

Zhao, Xiaohua; Li, Jiahui; Ma, Jianming; Rong, Jian

2016-01-01

Traffic control devices are one of the most significant factors affecting driving behavior. In China, there is a lack of installation guidelines or standards for traffic control devices in school zones. In addition, little research has been done to examine the effects of traffic control devices on driving behavior. Few guidelines have been established for implementing traffic control devices in school zones in China. This research conducted a driving simulator experiment to assess the effects of school zone signs and markings for two different types of schools. The efficiency of these traffic control devices was evaluated using four variables derived from the driving simulation, including average speed, relative speed difference, standard deviation of acceleration, and 85th percentile speed. Results showed that traffic control devices such as the Flashing Beacon and School Crossing Ahead Warning Assembly, the Reduce Speed and School Crossing Warning Assembly, and the School Crossing Ahead Pavement Markings were recommended for school zones adjacent to a major multilane roadway, which is characterized by a median strip, high traffic volume, high-speed traffic and the presence of pedestrian crossing signals. The School Crossing Ahead Pavement Markings were recommended for school zones on a minor two-lane roadway, which is characterized by low traffic volume, low speed, and no pedestrian crossing signals.

Development of a traffic control devices and pavement markings manual for Iowa's cities and counties with a survey of common practices.

DOT National Transportation Integrated Search

2001-04-01

Local transportation agencies are responsible for a significant investment in traffic control : devices and pavement markings. Thousands of signs and other inventory items, equipment, : facilities, and staff are all dedicated to the installation and ...

Item Unique Identification (IUID) Marking for a Littoral Combat Ship (LCS) Class Mission Module (MM) at the Mission Package Support Facility (MPSF): Implementation Analysis and Development of Optimal Marking Procedures

DTIC Science & Technology

2010-06-01

scanners, readers, or imagers. These types of ADCS devices use two slightly different technologies. Laser scanners use a photodiode to measure the...structure of a ship, but the LCS utilizes modular mission packages that can be removed and replaced when the threat , environment, or mission changes...would need to support a wide array of business applications and users (Clarion, 2009). The DoD’s solution to this deficiency is called IUID. IUID is a

Single cell and single molecule techniques for the analysis of the epigenome

NASA Astrophysics Data System (ADS)

Wallin, Christopher Benjamin

Epigenetic regulation is a critical biological process for the health and development of a cell. Epigenetic regulation is facilitated by covalent modifications to the underlying DNA and chromatin proteins. A fundamental understanding of these epigenetic modifications and their associated interactions at the molecular scale is necessary to explain phenomena including cellular identity, stem cell plasticity, and neoplastic transformation. It is widely known that abnormal epigenetic profiles have been linked to many diseases, most notably cancer. While the field of epigenetics has progressed rapidly with conventional techniques, significant advances remain to be made with respect to combinatoric analysis of epigenetic marks and single cell epigenetics. Therefore, in this dissertation, I will discuss our development of devices and methodologies to address these pertinent issues. First, we designed a preparatory polydimethylsiloxane (PDMS) microdevice for the extraction, purification, and stretching of human chromosomal DNA and chromatin from small cell populations down to a single cell. The valveless device captures cells by size exclusion within the micropillars, entraps the DNA or chromatin in the micropillars after cell lysis, purifies away the cellular debris, and fluorescently labels the DNA and/or chromatin all within a single reaction chamber. With the device, we achieve nearly 100% extraction efficiency of the DNA. The device is also used for in-channel immunostaining of chromatin followed by downstream single molecule chromatin analysis in nanochannels (SCAN). Second, using multi-color, time-correlated single molecule measurements in nanochannels, simultaneous coincidence detection of 2 epigenetic marks is demonstrated. Coincidence detection of 3 epigenetic marks is also established using a pulsed interleaved excitation scheme. With these two promising results, genome-wide quantification of epigenetic marks was pursued. Unfortunately, quantitative SCAN never materialized. Reasons for this, including poor signal to background, are explained in detail. Third, development of mobility-SCAN, an analytical technique for measuring and analyzing single molecules based on their fluorescent signature and their electrophoretic mobility in nanochannels is described. We use the technique to differentiate biomolecules from complex mixtures and derive parameters such as diffusion coefficients and effective charges. Finally, the device is used to detect binding interactions of various complexes similar to affinity capillary electrophoresis, but on a single molecule level. Fourth, we conclude by briefly discussing SCAN-sort, a technique to sort individual chromatin molecules based on their fluorescent emissions for further downstream analysis such as DNA sequencing. We demonstrate a 2-fold enrichment of chromatin from sorting and discuss possible system modifications for better performance in the future.

Performance analysis of resistive switching devices based on BaTiO3 thin films

NASA Astrophysics Data System (ADS)

Samardzic, Natasa; Kojic, Tijana; Vukmirovic, Jelena; Tripkovic, Djordjije; Bajac, Branimir; Srdic, Vladimir; Stojanovic, Goran

2016-03-01

Resitive switching devices, memristors, have recenty attracted much attention due to promising performances and potential applications in the field of logic and memory devices. Here, we present thin film BaTiO3 based memristor fabricated using ink-jet printing technique. Active material is a single layer barium titanate film with thickness of ̴100 nm, sandwitched between metal electodes. Printing parameters were optimized aiming to achieve stable drop flow and uniform printed layer. Current-voltage characteristics show typical memristive behavior with pinched hysteresis loop crossed at the origin, with marked differences between High Resistive State (HRS) and Low Resistive State (LRS). Obtained resistive states are stable during numerous switching processes. The device also shows unipolar switching effect for negative voltage impulses. Variable voltage impulse amplitudes leads to the shifting of the energy levels of electode contacts resulting in changing of the overall current through the device. Structural charcterization have been performed using XRD analysis and SEM micrography. High-temperature current-voltage measurements combined with transport parameter analysis using Hall efect measurement system (HMS 3000) and Impedance Analyzer AC measurements allows deeper insigth into conduction mechanism of ferroelectric memristors.

9 CFR 312.5 - Official seals for transportation of products.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Official seals for transportation of... INSPECTION AND CERTIFICATION OFFICIAL MARKS, DEVICES AND CERTIFICATES § 312.5 Official seals for... and any seal approved by the Administrator for applying such mark shall be an official device for...

9 CFR 312.5 - Official seals for transportation of products.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Official seals for transportation of... INSPECTION AND CERTIFICATION OFFICIAL MARKS, DEVICES AND CERTIFICATES § 312.5 Official seals for... and any seal approved by the Administrator for applying such mark shall be an official device for...

46 CFR 199.178 - Marking of stowage locations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Marking of stowage locations. 199.178 Section 199.178... locations. (a) Containers, brackets, racks, and other similar stowage locations for lifesaving equipment... that location. (b) If more than one device is stowed in a location, the number of devices stowed must...

49 CFR 221.14 - Marking devices.

Code of Federal Regulations, 2013 CFR

2013-10-01

... side of the horizontal center line as defined in terms of the 50 candela intensity points; (3) A color defined by the red-orange-amber color range; and (4) If a flashing light is used, a flash rate of not less... intensity of not less than 100 candela nor more than 1000 candela for flashing lights) as measured at the...

49 CFR 221.14 - Marking devices.

Code of Federal Regulations, 2012 CFR

2012-10-01

... side of the horizontal center line as defined in terms of the 50 candela intensity points; (3) A color defined by the red-orange-amber color range; and (4) If a flashing light is used, a flash rate of not less... intensity of not less than 100 candela nor more than 1000 candela for flashing lights) as measured at the...

49 CFR 221.14 - Marking devices.

Code of Federal Regulations, 2014 CFR

2014-10-01

... side of the horizontal center line as defined in terms of the 50 candela intensity points; (3) A color defined by the red-orange-amber color range; and (4) If a flashing light is used, a flash rate of not less... intensity of not less than 100 candela nor more than 1000 candela for flashing lights) as measured at the...

49 CFR 221.14 - Marking devices.

Code of Federal Regulations, 2011 CFR

2011-10-01

... side of the horizontal center line as defined in terms of the 50 candela intensity points; (3) A color defined by the red-orange-amber color range; and (4) If a flashing light is used, a flash rate of not less... intensity of not less than 100 candela nor more than 1000 candela for flashing lights) as measured at the...

46 CFR 28.135 - Lifesaving equipment markings.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY UNINSPECTED VESSELS REQUIREMENTS FOR COMMERCIAL... Resolution A.658(16). (d) A wearable personal flotation device must be marked with the name of either the... Equipment Markings Item Markings Required Name of vessel Retroflective material Wearable personal flotation...

46 CFR 28.135 - Lifesaving equipment markings.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY UNINSPECTED VESSELS REQUIREMENTS FOR COMMERCIAL... Resolution A.658(16). (d) A wearable personal flotation device must be marked with the name of either the... Equipment Markings Item Markings Required Name of vessel Retroflective material Wearable personal flotation...

Wind noise within and across behind-the-ear and miniature behind-the-ear hearing aids.

PubMed

Zakis, Justin A; Hawkins, Daniel J

2015-10-01

Previous studies investigated wind noise with Behind-The-Ear (BTE) hearing aids, but not the more common mini-BTE style of device, which typically has a smaller shell and microphones located more deeply behind the pinna. The current study investigated wind-noise levels across one BTE and two mini-BTE devices, and between the front and rear omni-directional microphones within devices. Levels were measured at two wind speeds (3 and 6 m/s) and 36 wind azimuths (10° increments). The pattern of wind-noise level versus azimuth was similar across mini-BTE devices, and differed for the BTE device. However, mean levels were markedly different across mini-BTE devices, and could be higher, lower, or similar to those of the BTE device. For within-device level differences, the pattern and mean across azimuth were similar across mini-BTE devices, and differed for the BTE device. Wind noise had the potential to slightly or severely reduce speech intelligibility at 3 or 6 m/s, respectively, across all devices.

77 FR 3159 - Electronic Export Application and Certification Charge; Flexibility in the Requirements for...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-23

... Marks, Devices, and Certificates; Egg Products Export Certification AGENCY: Food Safety and Inspection... inspection marks, devices, and certificates. In addition, FSIS is proposing to amend the egg product export... possible under the current system. The Egg Products Inspection Act (EPIA) (21 U.S.C. 1031-1056) does not...

49 CFR 221.17 - Movement of defective equipment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Movement of defective equipment. 221.17 Section... Marking Devices § 221.17 Movement of defective equipment. (a) Whenever the marking device prescribed in... of the defect, can be placed only at the rear of a train for movement to the next forward location at...

49 CFR 221.13 - Marking device display.

Code of Federal Regulations, 2010 CFR

2010-10-01

... visibility that the end silhouette of a standard box car cannot be seen from 1/2 mile on tangent track by a... with, (2) display on the trailing end of the rear car of that train, and (3) continuously illuminate or... cell activation mechanism complying with paragraph (c) of this section, the marking devices prescribed...

75 FR 20935 - National Standards for Traffic Control Devices; the Manual on Uniform Traffic Control Devices for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-22

... for implementation and continued use of a maintenance method that is designed to maintain pavement... method that is designed to maintain pavement marking retroreflectivity at or above the established levels... every pavement marking in its jurisdiction. Instead, agencies must implement methods designed to provide...

7 CFR 58.2 - Designation of official certificates, memoranda, marks, identifications, and devices for purpose...

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Designation of official certificates, memoranda, marks, identifications, and devices for purpose of the Agricultural Marketing Act. 58.2 Section 58.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices),...

7 CFR 56.2 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Designation of official certificates, memoranda, marks, other identifications, and devices for purposes of the Agricultural Marketing Act. 56.2 Section 56.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices),...

Development of a traffic control devices and pavement markings manual for Iowa's cities and counties with a survey of common practices

DOT National Transportation Integrated Search

2001-04-01

The purpose of this project was to develop and distribute a manual that would provide local agencies in Iowa with practical advice and guidance for traffic control devices and pavement markings installation and maintenance. The project included the f...

Revealing Optical Components

NASA Technical Reports Server (NTRS)

2002-01-01

The Optical Vector Analyzer (OVA) 1550 significantly reduces the time and cost of testing sophisticated optical components. The technology grew from the research Luna Technologies' Dr. Mark Froggatt conducted on optical fiber strain measurement while working at Langley Research Center. Dr. Froggatt originally developed the technology for non- destructive evaluation testing at Langley. The new technique can provide 10,000 independent strain measurements while adding less than 10 grams to the weight of the vehicle. The OVA is capable of complete linear characterization of single-mode optical components used in high- bit-rate applications. The device can test most components over their full range in less than 30 seconds, compared to the more than 20 minutes required by other testing methods. The dramatically shortened measurement time results in increased efficiency in final acceptance tests of optical devices, and the comprehensive data produced by the instrument adds considerable value for component consumers. The device eliminates manufacturing bottlenecks, while reducing labor costs and wasted materials during production.

Evaluation of pavement marking performance.

DOT National Transportation Integrated Search

2008-06-01

The objective of the investigation was to evaluate the useful life of pavement markings. The Manual on Uniform Traffic Control Devices (MUTCD) provides general guidelines for the application and installation of pavement markings. However, performance...

9 CFR 312.3 - Official marks and devices to identify inspected and passed equine products.

Code of Federal Regulations, 2010 CFR

2010-01-01

... inspected and passed equine products. 312.3 Section 312.3 Animals and Animal Products FOOD SAFETY AND... § 312.3 Official marks and devices to identify inspected and passed equine products. (a) The official... § 317.2 of this subchapter to identify inspected and passed mule and other (nonhorse) equine carcasses...

7 CFR 61.2a - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Designation of official certificates, memoranda, marks, other identifications, and devices for purpose of the Agricultural Marketing Act. 61.2a Section 61.2a Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices)...

9 CFR 592.5 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 9 Animals and Animal Products 2 2013-01-01 2013-01-01 false Designation of official certificates, memoranda, marks, other identifications, and devices for purposes of the Agricultural Marketing Act. 592.5 Section 592.5 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE EGG PRODUCTS INSPECTION VOLUNTARY...

9 CFR 592.5 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 9 Animals and Animal Products 2 2012-01-01 2012-01-01 false Designation of official certificates, memoranda, marks, other identifications, and devices for purposes of the Agricultural Marketing Act. 592.5 Section 592.5 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE EGG PRODUCTS INSPECTION VOLUNTARY...

9 CFR 592.5 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 9 Animals and Animal Products 2 2014-01-01 2014-01-01 false Designation of official certificates, memoranda, marks, other identifications, and devices for purposes of the Agricultural Marketing Act. 592.5 Section 592.5 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE EGG PRODUCTS INSPECTION VOLUNTARY...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mutaf, Yildirim D.; Yi, Byong Yong; Prado, Karl

Purpose: A dedicated stereotactic gamma irradiation device, the GammaPod Trade-Mark-Sign from Xcision Medical Systems, was developed specifically to treat small breast cancers. This study presents the first evaluation of dosimetric and geometric characteristics from the initial prototype installed at University of Maryland Radiation Oncology Department. Methods: The GammaPod Trade-Mark-Sign stereotactic radiotherapy device is an assembly of a hemi-spherical source carrier containing 36 {sup 60}Co sources, a tungsten collimator, a dynamically controlled patient support table, and the breast immobilization system which also functions as a stereotactic frame. The source carrier contains the sources in six columns spaced longitudinally at 60 Degree-Signmore » intervals and it rotates together with the variable-size collimator to form 36 noncoplanar, concentric arcs focused at the isocenter. The patient support table enables motion in three dimensions to position the patient tumor at the focal point of the irradiation. The table moves continuously in three cardinal dimensions during treatment to provide dynamic shaping of the dose distribution. The breast is immobilized using a breast cup applying a small negative pressure, where the immobilization cup is embedded with fiducials also functioning as the stereotactic frame for the breast. Geometric and dosimetric evaluations of the system as well as a protocol for absorbed dose calibration are provided. Dosimetric verifications of dynamically delivered patient plans are performed for seven patients using radiochromic films in hypothetical preop, postop, and target-in-target treatment scenarios. Results: Loaded with 36 {sup 60}Co sources with cumulative activity of 4320 Ci, the prototype GammaPod Trade-Mark-Sign unit delivers 5.31 Gy/min at the isocenter using the largest 2.5 cm diameter collimator. Due to the noncoplanar beam arrangement and dynamic dose shaping features, the GammaPod Trade-Mark-Sign device is found to deliver uniform doses to targets with good conformity. The spatial accuracy of the device to locate the radiation isocenter is determined to be less than 1 mm. Single shot profiles with 2.5 cm collimator are measured with radiochromic film and found to be in good agreement with respect to the Monte Carlo based calculations (congruence of FWHM less than 1 mm). Dosimetric verifications corresponding to all hypothetical treatment plans corresponding to three target scenarios for each of the seven patients demonstrated good agreement with gamma index pass rates of better than 97% (99.0%{+-} 0.7%). Conclusions: Dosimetric evaluation of the first GammaPod Trade-Mark-Sign stereotactic breast radiotherapy unit was performed and the dosimetric and spatial accuracy of this novel technology is found to be feasible with respect to clinical radiotherapy standards. The observed level of agreement between the treatment planning system calculations and dosimetric measurements has confirmed that the system can deliver highly complex treatment plans with remarkable geometric and dosimetric accuracy.« less

Referential shift in Nicaraguan Sign Language: a transition from lexical to spatial devices

PubMed Central

Kocab, Annemarie; Pyers, Jennie; Senghas, Ann

2015-01-01

Even the simplest narratives combine multiple strands of information, integrating different characters and their actions by expressing multiple perspectives of events. We examined the emergence of referential shift devices, which indicate changes among these perspectives, in Nicaraguan Sign Language (NSL). Sign languages, like spoken languages, mark referential shift grammatically with a shift in deictic perspective. In addition, sign languages can mark the shift with a point or a movement of the body to a specified spatial location in the three-dimensional space in front of the signer, capitalizing on the spatial affordances of the manual modality. We asked whether the use of space to mark referential shift emerges early in a new sign language by comparing the first two age cohorts of deaf signers of NSL. Eight first-cohort signers and 10 second-cohort signers watched video vignettes and described them in NSL. Narratives were coded for lexical (use of words) and spatial (use of signing space) devices. Although the cohorts did not differ significantly in the number of perspectives represented, second-cohort signers used referential shift devices to explicitly mark a shift in perspective in more of their narratives. Furthermore, while there was no significant difference between cohorts in the use of non-spatial, lexical devices, there was a difference in spatial devices, with second-cohort signers using them in significantly more of their narratives. This suggests that spatial devices have only recently increased as systematic markers of referential shift. Spatial referential shift devices may have emerged more slowly because they depend on the establishment of fundamental spatial conventions in the language. While the modality of sign languages can ultimately engender the syntactic use of three-dimensional space, we propose that a language must first develop systematic spatial distinctions before harnessing space for grammatical functions. PMID:25713541

Referential shift in Nicaraguan Sign Language: a transition from lexical to spatial devices.

PubMed

Kocab, Annemarie; Pyers, Jennie; Senghas, Ann

2014-01-01

Even the simplest narratives combine multiple strands of information, integrating different characters and their actions by expressing multiple perspectives of events. We examined the emergence of referential shift devices, which indicate changes among these perspectives, in Nicaraguan Sign Language (NSL). Sign languages, like spoken languages, mark referential shift grammatically with a shift in deictic perspective. In addition, sign languages can mark the shift with a point or a movement of the body to a specified spatial location in the three-dimensional space in front of the signer, capitalizing on the spatial affordances of the manual modality. We asked whether the use of space to mark referential shift emerges early in a new sign language by comparing the first two age cohorts of deaf signers of NSL. Eight first-cohort signers and 10 second-cohort signers watched video vignettes and described them in NSL. Narratives were coded for lexical (use of words) and spatial (use of signing space) devices. Although the cohorts did not differ significantly in the number of perspectives represented, second-cohort signers used referential shift devices to explicitly mark a shift in perspective in more of their narratives. Furthermore, while there was no significant difference between cohorts in the use of non-spatial, lexical devices, there was a difference in spatial devices, with second-cohort signers using them in significantly more of their narratives. This suggests that spatial devices have only recently increased as systematic markers of referential shift. Spatial referential shift devices may have emerged more slowly because they depend on the establishment of fundamental spatial conventions in the language. While the modality of sign languages can ultimately engender the syntactic use of three-dimensional space, we propose that a language must first develop systematic spatial distinctions before harnessing space for grammatical functions.

Hypothermia Severely Effects Performance of Nitinol-Based Endovascular Grafts In Vitro

PubMed Central

Robich, Michael P.; Hagberg, Robert; Schermerhorn, Marc L.; Pomposelli, Frank B.; Nilson, Michael C.; Gendron, Michelle L.; Sellke, Frank W.; Rodriguez, Roberto

2012-01-01

Background Nitinol is an alloy that serves as the base for numerous medical devices, including the GORE TAG Thoracic Endoprosthesis (W.L. Gore & Associates, Flagstaff, AZ) thoracic aortic graft device. Given the increasing use of therapeutic hypothermia used during the placement these devices and in post– cardiac arrest situations, we sought to understand the impact of hypothermia on this device. Methods Five 34-mm TAG devices were deployed in a temperature-controlled chamber at 20°C, 25°C, 30°C, 35°, and 37°C (25 total devices). A halographic measurement device was used to measure radial expansive force and normalized to the force at 37°C. Three 34-mm TAG devices were similarly deployed in a temperature-controlled water bath at each of the above temperatures. A laser micrometer was utilized to measure deployed diameter. Results A statistically significant decrease in expansive force at 20°C, 25°C, and 30°C of 65%, 46%, and 6%, respectively, was noted. A statistically significant decrease in radial diameter at 20°C and 25°C of 17% and 11%, respectively, was noted. Although a 9% difference was noted at 30°C, it was not significant. Conclusions The nitinol-based TAG device shows marked decreases in radial expansive force and deployed diameter at temperatures at or below 30°C. Surgeons should be aware of the potential implications of placing nitinol-based endoprostheses in hypothermic conditions. In addition, all health care providers should be aware of the changes that occur in nitinol-based endoprostheses during therapeutic hypothermia. PMID:22385821

Safety by design: effects of operating room floor marking on the position of surgical devices to promote clean air flow compliance and minimise infection risks.

PubMed

de Korne, Dirk F; van Wijngaarden, Jeroen D H; van Rooij, Jeroen; Wauben, Linda S G L; Hiddema, U Frans; Klazinga, Niek S

2012-09-01

To evaluate the use of floor marking on the positioning of surgical devices within the clean air flow in an operating room (OR) to minimise infection risk. Laminar flow clean air systems are important in preventing infection in ORs but, for optimal results, surgical devices must be correctly positioned. The authors evaluated floor marking in four ORs at an eye hospital using time series analysis. Through observations during 829 surgeries over a 20-month period, the positions of surgical devices were determined. Eight semistructured interviews with surgical staff were conducted to assess user experiences and team dynamics. Before marking, the instrument table was positioned completely within the laminar flow in only 6.1% of the cases. This increased to 36.1% and finally 53.8%. Mayo stands were increasingly positioned within the laminar flow: from 74.2% to 84.7%. The surgical lamp decreasingly obstructed flow: from 41.8% to 28.7%. At T3 (20 months), however, in 48.6% of the applicable cases the lamp was positioned in the flow again. Discussions and site visits between airside operators and surgical staff resulted in increasing awareness of specific risk areas in the OR. OR floor markings facilitated and stimulated safety awareness and resulted in significantly increased compliance with the positioning of surgical devices in the clean air flow. Safety and quality approaches in hospital care, therefore, should include a human factors approach that focuses on system design in addition to teaching clinical and non-technical skills.

C-shaped specimen plane strain fracture toughness tests. [metallic materials

NASA Technical Reports Server (NTRS)

Buzzard, R. T.; Fisher, D. M.

1977-01-01

Test equipment, procedures, and data obtained in the evaluation of C-shaped specimens are presented. Observations reported on include: specimen preparation and dimensional measurement; modifications to the standard ASTM E 399 displacement gage, which permit punch mark gage point engagement; and a measurement device for determining the interior and exterior radii of ring segments. Load displacement ratios were determined experimentally which agreed with analytically determined coefficients for three different gage lengths on the inner surfaces of radially-cracked ring segments.

9 CFR 309.18 - Official marks and devices for purposes of ante-mortem inspection.

Code of Federal Regulations, 2011 CFR

2011-01-01

... purposes of ante-mortem inspection. 309.18 Section 309.18 Animals and Animal Products FOOD SAFETY AND... marks and devices for purposes of ante-mortem inspection. (a) All livestock required by this part to be identified as U.S. Suspects shall be tagged with a serially numbered metal ear tag bearing the term “U.S...

9 CFR 309.18 - Official marks and devices for purposes of ante-mortem inspection.

Code of Federal Regulations, 2010 CFR

2010-01-01

... purposes of ante-mortem inspection. 309.18 Section 309.18 Animals and Animal Products FOOD SAFETY AND... marks and devices for purposes of ante-mortem inspection. (a) All livestock required by this part to be identified as U.S. Suspects shall be tagged with a serially numbered metal ear tag bearing the term “U.S...

9 CFR 309.18 - Official marks and devices for purposes of ante-mortem inspection.

Code of Federal Regulations, 2014 CFR

2014-01-01

... purposes of ante-mortem inspection. 309.18 Section 309.18 Animals and Animal Products FOOD SAFETY AND... marks and devices for purposes of ante-mortem inspection. (a) All livestock required by this part to be identified as U.S. Suspects shall be tagged with a serially numbered metal ear tag bearing the term “U.S...

9 CFR 309.18 - Official marks and devices for purposes of ante-mortem inspection.

Code of Federal Regulations, 2012 CFR

2012-01-01

... purposes of ante-mortem inspection. 309.18 Section 309.18 Animals and Animal Products FOOD SAFETY AND... marks and devices for purposes of ante-mortem inspection. (a) All livestock required by this part to be identified as U.S. Suspects shall be tagged with a serially numbered metal ear tag bearing the term “U.S...

9 CFR 309.18 - Official marks and devices for purposes of ante-mortem inspection.

Code of Federal Regulations, 2013 CFR

2013-01-01

... purposes of ante-mortem inspection. 309.18 Section 309.18 Animals and Animal Products FOOD SAFETY AND... marks and devices for purposes of ante-mortem inspection. (a) All livestock required by this part to be identified as U.S. Suspects shall be tagged with a serially numbered metal ear tag bearing the term “U.S...

21 CFR 888.4800 - Template for clinical use.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) MEDICAL DEVICES ORTHOPEDIC DEVICES Surgical Devices § 888.4800 Template for clinical use. (a... purposes, such as selecting or positioning orthopedic implants or guiding the marking of tissue before...

21 CFR 888.4800 - Template for clinical use.

Code of Federal Regulations, 2014 CFR

2014-04-01

...) MEDICAL DEVICES ORTHOPEDIC DEVICES Surgical Devices § 888.4800 Template for clinical use. (a... purposes, such as selecting or positioning orthopedic implants or guiding the marking of tissue before...

21 CFR 888.4800 - Template for clinical use.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) MEDICAL DEVICES ORTHOPEDIC DEVICES Surgical Devices § 888.4800 Template for clinical use. (a... purposes, such as selecting or positioning orthopedic implants or guiding the marking of tissue before...

Realizing the measure-device-independent quantum-key-distribution with passive heralded-single photon sources

PubMed Central

Wang, Qin; Zhou, Xing-Yu; Guo, Guang-Can

2016-01-01

In this paper, we put forward a new approach towards realizing measurement-device-independent quantum key distribution with passive heralded single-photon sources. In this approach, both Alice and Bob prepare the parametric down-conversion source, where the heralding photons are labeled according to different types of clicks from the local detectors, and the heralded ones can correspondingly be marked with different tags at the receiver’s side. Then one can obtain four sets of data through using only one-intensity of pump light by observing different kinds of clicks of local detectors. By employing the newest formulae to do parameter estimation, we could achieve very precise prediction for the two-single-photon pulse contribution. Furthermore, by carrying out corresponding numerical simulations, we compare the new method with other practical schemes of measurement-device-independent quantum key distribution. We demonstrate that our new proposed passive scheme can exhibit remarkable improvement over the conventional three-intensity decoy-state measurement-device-independent quantum key distribution with either heralded single-photon sources or weak coherent sources. Besides, it does not need intensity modulation and can thus diminish source-error defects existing in several other active decoy-state methods. Therefore, if taking intensity modulating errors into account, our new method will show even more brilliant performance. PMID:27759085

A stereotactic method for image-guided transcranial magnetic stimulation validated with fMRI and motor-evoked potentials.

PubMed

Neggers, S F W; Langerak, T R; Schutter, D J L G; Mandl, R C W; Ramsey, N F; Lemmens, P J J; Postma, A

2004-04-01

Transcranial Magnetic Stimulation (TMS) delivers short magnetic pulses that penetrate the skull unattenuated, disrupting neural processing in a noninvasive, reversible way. To disrupt specific neural processes, coil placement over the proper site is critical. Therefore, a neural navigator (NeNa) was developed. NeNa is a frameless stereotactic device using structural and functional magnetic resonance imaging (fMRI) data to guide TMS coil placement. To coregister the participant's head to his MRI, 3D cursors are moved to anatomical landmarks on a skin rendering of the participants MRI on a screen, and measured at the head with a position measurement device. A method is proposed to calculate a rigid body transformation that can coregister both sets of coordinates under realistic noise conditions. After coregistration, NeNa visualizes in real time where the device is located with respect to the head, brain structures, and activated areas, enabling precise placement of the TMS coil over a predefined target region. NeNa was validated by stimulating 5 x 5 positions around the 'motor hotspot' (thumb movement area), which was marked on the scalp guided by individual fMRI data, while recording motor-evoked potentials (MEPs) from the abductor pollicis brevis (APB). The distance between the center of gravity (CoG) of MEP responses and the location marked on the scalp overlying maximum fMRI activation was on average less then 5 mm. The present results demonstrate that NeNa is a reliable method for image-guided TMS coil placement.

Transportation-markings database : composite categories, classification & index. Part I 5, Volume 3, additional studies

DOT National Transportation Integrated Search

2006-01-01

The Transportation-Markings Database project (within the T-M Monograph Series) began in 1997 with the publishing of the initial component, Transportation-Markings Database: Marine. That study was joined by T-M Database: Traffic Control Devices (1998)...

Clinical results of computerized tomography-based simulation with laser patient marking.

PubMed

Ragan, D P; Forman, J D; He, T; Mesina, C F

1996-02-01

Accuracy of a patient treatment portal marking device and computerized tomography (CT) simulation have been clinically tested. A CT-based simulator has been assembled based on a commercial CT scanner. This includes visualization software and a computer-controlled laser drawing device. This laser drawing device is used to transfer the setup, central axis, and/or radiation portals from the CT simulator to the patient for appropriate patient skin marking. A protocol for clinical testing is reported. Twenty-five prospectively, sequentially accessioned patients have been analyzed. The simulation process can be completed in an average time of 62 min. Under many cases, the treatment portals can be designed and the patient marked in one session. Mechanical accuracy of the system was found to be within +/- 1mm. The portal projection accuracy in clinical cases is observed to be better than +/- 1.2 mm. Operating costs are equivalent to the conventional simulation process it replaces. Computed tomography simulation is a clinical accurate substitute for conventional simulation when used with an appropriate patient marking system and digitally reconstructed radiographs. Personnel time spent in CT simulation is equivalent to time in conventional simulation.

46 CFR 53.05-5 - Discharge capacities and valve markings.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Discharge capacities and valve markings. 53.05-5 Section 53.05-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Pressure Relieving Devices (Article 4) § 53.05-5 Discharge capacities and valve markings. The discharge capacities and valve markings must...

46 CFR 53.05-5 - Discharge capacities and valve markings.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Discharge capacities and valve markings. 53.05-5 Section 53.05-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Pressure Relieving Devices (Article 4) § 53.05-5 Discharge capacities and valve markings. The discharge capacities and valve markings must...

46 CFR 53.05-5 - Discharge capacities and valve markings.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Discharge capacities and valve markings. 53.05-5 Section 53.05-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Pressure Relieving Devices (Article 4) § 53.05-5 Discharge capacities and valve markings. The discharge capacities and valve markings must...

46 CFR 53.05-5 - Discharge capacities and valve markings.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Discharge capacities and valve markings. 53.05-5 Section 53.05-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Pressure Relieving Devices (Article 4) § 53.05-5 Discharge capacities and valve markings. The discharge capacities and valve markings must...

46 CFR 53.05-5 - Discharge capacities and valve markings.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Discharge capacities and valve markings. 53.05-5 Section 53.05-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS Pressure Relieving Devices (Article 4) § 53.05-5 Discharge capacities and valve markings. The discharge capacities and valve markings must...

Improvement of CD-SEM mark position measurement accuracy

NASA Astrophysics Data System (ADS)

Kasa, Kentaro; Fukuhara, Kazuya

2014-04-01

CD-SEM is now attracting attention as a tool that can accurately measure positional error of device patterns. However, the measurement accuracy can get worse due to pattern asymmetry as in the case of image based overlay (IBO) and diffraction based overlay (DBO). For IBO and DBO, a way of correcting the inaccuracy arising from measurement patterns was suggested. For CD-SEM, although a way of correcting CD bias was proposed, it has not been argued how to correct the inaccuracy arising from pattern asymmetry using CD-SEM. In this study we will propose how to quantify and correct the measurement inaccuracy affected by pattern asymmetry.

Assessment of the OsteoMark-Navigation System for Oral and Maxillofacial Surgery

PubMed Central

Peacock, Zachary S.; Magill, John C.; Tricomi, Brad J.; Murphy, Brian A.; Nikonovskiy, Vladimir; Hata, Nobuhiko; Chauvin, Laurent; Troulis, Maria J.

2015-01-01

Purpose To assess the accuracy of a novel navigation system for maxillofacial surgery using human cadavers and a live minipig model. Methods We describe and test an electromagnetic tracking system (OsteoMark Navigation) that uses simple sensors to determine position and orientation of a hand held pencil-like marking device. The device can translate 3-dimensional computed tomographic data intraoperatively to allow the surgeon to localize and draw a proposed osteotomy or the margins of a tumor on the bone. The accuracy of OsteoMark-Navigation in locating and marking osteotomies and screw positions in human cadaver heads was assessed. In Group 1 (n=3, 6 sides), Osteomark-Navigation marked osteotomies and screw positions were compared to virtual treatment plans In Group 2 (n=3, 6 sides), marked osteotomies and screw positions for distraction osteogenesis devices were compared to those carried out using fabricated guide-stents. Three metrics were used to document precision and accuracy. In Group 3 (n=1), the system was tested in a standard operating room environment. Results For Group 1, the mean error between points was 0.7mm (horizontal) and 1.7mm (vertical). When compared to the posterior and inferior mandibular border the mean error was 1.2 and 1.7mm, respectively. For Group 2, the mean discrepancy between points marked by Osteomark-Navigation and the surgical guides was 1.9 mm (range 0-4.1 mm). The system maintained accuracy on a live minipig in a standard operating room environment. Conclusion Based on this research OsteoMark-Navigation is potentially a powerful tool for clinical use in maxillofacial surgery. It has accuracy and precision comparable to existing clinical applications. PMID:25865717

Intraoperative loss of core biopsy clips: clinical implications.

PubMed

Calhoun, Kristine; Giuliano, Armando; Brenner, R James

2008-03-01

The purpose of this study was to report the occurrence of intraoperative loss of metallic marking clips placed during image-guided biopsy and to hypothesize the likely mechanism of this clinical problem. From January 2003 through December 2004, patients presenting for preoperative mammographic localization and operative excision of biopsy site marking clips were identified. Age, method of image-guided biopsy, number of excised specimens, and tissue diagnosis were determined. Specimen radiographs were used to identify cases of suspected intraoperative clip loss. Clips absent on specimen radiographs and postoperative mammograms were defined as lost intraoperatively. Biopsy site marking clips, surgical clips, and suction device apertures were measured. In 78 surgical procedures performed during the study period, three (3.8%) of the patients experienced clip loss. Specimen radiographs confirmed the absence of clips in all submitted tissues. A median of four (range, three to five) separate biopsy specimens were excised among these three cases. A healing biopsy site from the stereotactic biopsy preceding the clip placement procedure was confirmed in all cases. Absence of the metallic clip was confirmed on postoperative mammograms. The apertures of two types of suction device were four and two times those of the biopsy clips. Intraoperative loss of metallic clips placed at the conclusion of image-guided breast biopsy is unusual but can occur during subsequent surgical excision. Repeated inability to locate the clip on specimen radiographs after accurate preoperative localization should raise the suspicion that the target clip has been lost, not missed, during surgery, likely because of inadvertent removal of the clip with the suction device.

Technologies for the marking of fishing gear to identify gear components entangled on marine animals and to reduce abandoned, lost or otherwise discarded fishing gear.

PubMed

He, Pingguo; Suuronen, Petri

2018-04-01

Fishing gears are marked to establish and inform origin, ownership and position. More recently, fishing gears are marked to aid in capacity control, reduce marine litter due to abandoned, lost or otherwise discarded fishing gear (ALDFG) and assist in its recovery, and to combat illegal, unreported and unregulated (IUU) fishing. Traditionally, physical marking, inscription, writing, color, shape, and tags have been used for ownership and capacity purposes. Buoys, lights, flags, and radar reflectors are used for marking of position. More recently, electronic devices have been installed on marker buoys to enable easier relocation of the gear by owner vessels. This paper reviews gear marking technologies with focus on coded wire tags, radio frequency identification tags, Automatic Identification Systems, advanced electronic buoys for pelagic longlines and fish aggregating devices, and re-location technology if the gear becomes lost. Copyright © 2018 Elsevier Ltd. All rights reserved.

Pipe inspection and repair system

NASA Technical Reports Server (NTRS)

Schempf, Hagen (Inventor); Mutschler, Edward (Inventor); Chemel, Brian (Inventor); Boehmke, Scott (Inventor); Crowley, William (Inventor)

2004-01-01

A multi-module pipe inspection and repair device. The device includes a base module, a camera module, a sensor module, an MFL module, a brush module, a patch set/test module, and a marker module. Each of the modules may be interconnected to construct one of an inspection device, a preparation device, a marking device, and a repair device.

Simultaneous wireless assessment of intra-oral pH and temperature.

PubMed

Farella, M; Loke, C; Sander, S; Songini, A; Allen, M; Mei, L; Cannon, R D

2016-08-01

Intra-oral pH plays an important role in the pathogenesis of tooth erosion and decay, but there is limited information about its variation in real life settings. The aims of this research were to: 1) develop a wireless device, which can be used to continuously monitor intra-oral pH and temperature in real-time; 2) test and validate the device under controlled laboratory conditions; and 3) collect data in a natural environment in a sample of healthy volunteers. A wireless device for measuring pH and temperature simultaneously was developed, calibrated and validated against the gold standard glass electrode pH meter. A smart phone was used as data logger. The wireless device was embedded in an oral appliance and worn by eleven participants (mean age 31.1±6.9years) for 24h, while conducting standardised drinking tasks and regular daily activities. The wireless device could accurately measure pH and temperature both in vitro and in vivo. The recovery time following the swallow of a standard acidic drink varied markedly among individuals (mean=1.3±0.9min). The intra-oral pH and temperature recorded in the natural environment also showed a large inter- and intra-individual variability. The average intra-oral pH when asleep (6.7±0.5) was lower (p<0.001) than when awake (7.2±0.5). The average intra-oral temperature during sleep (35.6±0.5°C) was higher (p<0.001) than when awake (34.5±0.7°C). Intra-oral pH and temperature can be continuously and wirelessly assessed in real-life settings, and show individual-specific patterns with circadian variations. Intra-oral pH becomes slightly acidic during sleep while intra-oral temperature increases and fluctuates less. We propose a wireless device that is capable of measuring intra-oral pH over a 24-h period. We found marked inter-individual variation after acidic stimuli, and day to sleep time variation of both intra-oral temperature and pH. Our approach may provide new insight into the relationship between oral pH, tooth wear and decay. Copyright © 2016 Elsevier Ltd. All rights reserved.

Characterization of a Low-Cost Multi-Parameter Sensor for Resource Applications: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Habte, Aron M; Sengupta, Manajit; Andreas, Afshin M

Low-cost multi-parameter sensing and measurement devices enable cost-effective monitoring of the functional, operational reliability, efficiency, and resiliency of the electrical grid. The National Renewable Research Laboratory (NREL) Solar Radiation Research Laboratory (SRRL), in collaboration with Arable Labs Inc., deployed Arable Lab's Mark multi-parameter sensor system. The unique suite of system sensors measures the down-welling and upwelling shortwave solar resource and longwave radiation, humidity, air temperature, and ground temperature. This study describes the shortwave calibration, characteriza-tion, and validation of measurement accuracy of this instrument by comparison with existing instruments that are part of NREL-SRRL's Baseline Measurement System.

Wire Marking Results in a Small but Significant Reduction in Avian Mortality at Power Lines: A BACI Designed Study

PubMed Central

Barrientos, Rafael; Ponce, Carlos; Palacín, Carlos; Martín, Carlos A.; Martín, Beatriz; Alonso, Juan Carlos

2012-01-01

Background Collision with electric power lines is a conservation problem for many bird species. Although the implementation of flight diverters is rapidly increasing, few well-designed studies supporting the effectiveness of this costly conservation measure have been published. Methodology/Principal Findings We provide information on the largest worldwide marking experiment to date, including carcass searches at 35 (15 experimental, 20 control) power lines totalling 72.5 km, at both transmission (220 kV) and distribution (15 kV–45 kV) lines. We found carcasses of 45 species, 19 of conservation concern. Numbers of carcasses found were corrected to account for carcass losses due to removal by scavengers or being overlooked by researchers, resulting in an estimated collision rate of 8.2 collisions per km per month. We observed a small (9.6%) but significant decrease in the number of casualties after line marking compared to before line marking in experimental lines. This was not observed in control lines. We found no influence of either marker size (large vs. small spirals, sample of distribution lines only) or power line type (transmission vs. distribution, sample of large spirals only) on the collision rate when we analyzed all species together. However, great bustard mortality was slightly lower when lines were marked with large spirals and in transmission lines after marking. Conclusions Our results confirm the overall effectiveness of wire marking as a way to reduce, but not eliminate, bird collisions with power lines. If raw field data are not corrected by carcass losses due to scavengers and missed observations, findings may be biased. The high cost of this conservation measure suggests a need for more studies to improve its application, including wire marking with non-visual devices. Our findings suggest that different species may respond differently to marking, implying that species-specific patterns should be explored, at least for species of conservation concern. PMID:22396776

Line spread instrumentation for propagation measurements

NASA Technical Reports Server (NTRS)

Bailey, W. H., Jr.

1980-01-01

A line spread device capable of yielding direct measure of a laser beam's line spread function (LSF) was developed and employed in propagation tests conducted in a wind tunnel to examine optimal acoustical suppression techniques for laser cavities exposed to simulated aircraft aerodynamic environments. Measurements were made on various aerodynamic fences and cavity air injection techniques that effect the LSF of a propagating laser. Using the quiescent tunnel as a control, the relative effect of each technique on laser beam quality was determined. The optical instrument employed enabled the comparison of relative beam intensity for each fence or mass injection. It was found that fence height had little effect on beam quality but fence porosity had a marked effect, i.e., 58% porosity alleviated cavity resonance and degraded the beam the least. Mass injection had little effect on the beam LSF. The use of a direct LSF measuring device proved to be a viable means of determining aerodynamic seeing qualities of flow fields.

High-precision measurements of wetland sediment elevation. II The rod surface elevation table

USGS Publications Warehouse

Cahoon, D.R.; Lynch, J.C.; Perez, B.C.; Segura, B.; Holland, R.D.; Stelly, C.; Stephenson, G.; Hensel, P.

2002-01-01

A new high-precision device for measuring sediment elevation in emergent and shallow water wetland systems is described. The rod surface-elevation table (RSET) is a balanced, lightweight mechanical leveling device that attaches to both shallow ( 1 m in order to be stable. The pipe is driven to refusal but typically to a depth shallower than the rod bench mark because of greater surface resistance of the pipe. Thus, the RSET makes it possible to partition change in sediment elevation over shallower (e.g., the root zone) and deeper depths of the sediment profile than is possible with the SET. The confidence intervals for the height of an individual pin measured by two different operators with the RSET under laboratory conditions were A? 1.0 and A? 1.5 mm. Under field conditions, confidence intervals for the measured height of an individual pin ranged from A? 1.3 mm in a mangrove forest up to A? 4.3 mm in a salt marsh.

Digital mobile telephones and interference of ophthalmic equipment.

PubMed

Ang, G S; Lian, P; Ng, W S; Whyte, I; Ong, J M

2007-01-01

To assess the effect of mobile telephone electromagnetic interference on electronic ophthalmic equipment. Prospective audit with mobile telephones placed at distances of 3 m, 1 m, and 30 cm from, and in contact with, electronic ophthalmic equipment. Any interruption or cessation of the function of the ophthalmic device was assessed with the mobile telephones in standby, and in dialling or receiving modes. Any alterations of displayed digital figures or numbers were also assessed. A total of 23 electronic ophthalmic devices in two hospital ophthalmology outpatient departments were evaluated. All six mobile telephones used, and 22 (95.7%) of the 23 ophthalmic equipment evaluated had the Conformité Européene (CE) mark. No device showed any interruption or cessation of function. There were no alterations of displayed digital figures or numbers. The only effect of any kind was found with four instruments (1 non-CE marked), where there was temporary flickering on the screen, and only occurred when the mobile telephones were dialling or receiving at a distance of 30 cm or less from the instruments. This study shows that among the electronic ophthalmic devices tested, none suffered failure or interruption of function, from mobile telephone interference. Although not comprehensive for all ophthalmic equipment, the results question the need for a complete ban of mobile telephones in ophthalmic departments. It highlights the need for a controlled, objectively measured study of the clinically relevant effects of mobile telephones in the ophthalmology outpatient setting.

Considerations for an institution for evaluation of diabetes technology devices to improve their quality in the European Union.

PubMed

Heinemann, Lutz; Freckmann, Guido; Koschinsky, Theodor

2013-03-01

All medical devices used for self-monitoring of blood glucose (BG), insulin injection, continuous subcutaneous insulin infusion, and continuous glucose monitoring in the European Union (EU) must have a Communauté Européenne (CE) mark. However, the approval process for obtaining this mark is different from that used by the European Medicines Agency in the EU for drugs or by the Food and Drug Administration in the United States for such medical and in vitro diagnostic devices. The notified bodies involved in the CE mark process perform this evaluation in cooperation with the manufacturers. They have only limited diabetes know-how; they have to handle all kinds of medical devices. There are devices for therapy on the market in the EU (i.e., they have market approval) that do not fulfill quality requirements, as indicated, for example, in the international norm ISO 15197 for BG test systems. Evaluation of the performance of such systems is usually provided by the manufacturers. What is missing in the EU is an independent institution that performs regular and critical evaluation of the quality of devices used for diabetes therapy before and also after their market approval. The work of such an institution would focus on BG test systems (these represent two-thirds of the market of medical devices for diabetes treatment) but would also evaluate the performance of other devices. It has to be clarified what legal framework is required for such an institution and how it can be financed; probably this can be done in a shared manner by the manufacturers of such devices and the health insurance companies. Positive evaluation results should be a prerequisite prior to any reimbursement for such devices. © 2013 Diabetes Technology Society.

Determining electrically evoked compound action potential thresholds: a comparison of computer versus human analysis methods.

PubMed

Glassman, E Katelyn; Hughes, Michelle L

2013-01-01

Current cochlear implants (CIs) have telemetry capabilities for measuring the electrically evoked compound action potential (ECAP). Neural Response Telemetry (Cochlear) and Neural Response Imaging (Advanced Bionics [AB]) can measure ECAP responses across a range of stimulus levels to obtain an amplitude growth function. Software-specific algorithms automatically mark the leading negative peak, N1, and the following positive peak/plateau, P2, and apply linear regression to estimate ECAP threshold. Alternatively, clinicians may apply expert judgments to modify the peak markers placed by the software algorithms, or use visual detection to identify the lowest level yielding a measurable ECAP response. The goals of this study were to: (1) assess the variability between human and computer decisions for (a) marking N1 and P2 and (b) determining linear-regression threshold (LRT) and visual-detection threshold (VDT); and (2) compare LRT and VDT methods within and across human- and computer-decision methods. ECAP amplitude-growth functions were measured for three electrodes in each of 20 ears (10 Cochlear Nucleus® 24RE/CI512, and 10 AB CII/90K). LRT, defined as the current level yielding an ECAP with zero amplitude, was calculated for both computer- (C-LRT) and human-picked peaks (H-LRT). VDT, defined as the lowest level resulting in a measurable ECAP response, was also calculated for both computer- (C-VDT) and human-picked peaks (H-VDT). Because Neural Response Imaging assigns peak markers to all waveforms but does not include waveforms with amplitudes less than 20 μV in its regression calculation, C-VDT for AB subjects was defined as the lowest current level yielding an amplitude of 20 μV or more. Overall, there were significant correlations between human and computer decisions for peak-marker placement, LRT, and VDT for both manufacturers (r = 0.78-1.00, p < 0.001). For Cochlear devices, LRT and VDT correlated equally well for both computer- and human-picked peaks (r = 0.98-0.99, p < 0.001), which likely reflects the well-defined Neural Response Telemetry algorithm and the lower noise floor in the 24RE and CI512 devices. For AB devices, correlations between LRT and VDT for both peak-picker methods were weaker than for Cochlear devices (r = 0.69-0.85, p < 0.001), which likely reflect the higher noise floor of the system. Disagreement between computer and human decisions regarding the presence of an ECAP response occurred for 5 % of traces for Cochlear devices and 2.1 % of traces for AB devices. Results indicate that human and computer peak-picking methods can be used with similar accuracy for both Cochlear and AB devices. Either C-VDT or C-LRT can be used with equal confidence for Cochlear 24RE and CI512 recipients because both methods are strongly correlated with human decisions. However, for AB devices, greater variability exists between different threshold-determination methods. This finding should be considered in the context of using ECAP measures to assist with programming CIs.

9 CFR 381.204 - Marking of poultry products offered for entry; official import inspection marks and devices.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE AGENCY ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION AND VOLUNTARY INSPECTION AND CERTIFICATION POULTRY PRODUCTS... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Marking of poultry products offered...

Test and Evaluation Plan for the Explosive Device Detection Baseline (EDDB) Study

DTIC Science & Technology

1995-08-01

of civil aviation security has changed from hijackings to methods of countering bombings. This shift has markedly increased the need for improvements...to detect an environmental event or signal. SDT is a mathematical representation of human performance in deciding whether or not a signal is present...1970; Macmillan & Creelman , 1990; Snodgrass & Corwin, 1988). The chief difference between the measure c and its parametric alternative P3 lies in the

Safety and severity of accelerations delivered from whole body vibration exercise devices to standing adults.

PubMed

Muir, Jesse; Kiel, Douglas P; Rubin, Clinton T

2013-11-01

Whole body vibration devices are used as a means to augment training, and their potential to treat a range of musculoskeletal diseases and injuries is now being considered. The goal of this work is to determine the degree to which acceleration delivered by whole body vibration devices at the plantar surfaces of a standing human is transmitted through the axial and appendicular skeleton, and how this mechanical challenge corresponds to the safety threshold limit values established by the International Standards Organization ISO-2631. Non-blinded laboratory assessment of a range of whole body vibration devices as it pertains to acceleration transmission to healthy volunteers. Using skin and bite-bar mounted accelerometers, transmissibility to the tibia and cranium was determined in six healthy adults standing on a programmable whole body vibration device as a function of frequency and intensity. Measures of transmissibility were then made from three distinct types of whole body vibration platforms, which delivered a 50-fold range of peak-to-peak acceleration intensities (0.3-15.1 gp-p; where 1g is Earth's gravitational field). For a given frequency, transmissibility was independent of intensity when below 1g. Transmissibility declined non-linearly with increasing frequency. Depending on the whole body vibration device, vibration ranged from levels considered safe by ISO-2631 for up to 8h each day (0.3 gp-p @ 30 Hz), to levels that were seven times higher than what is considered a safe threshold for even 1 min of exposure each day (15.1 gp-p @ 30 Hz). Transmissibility to the cranium was markedly attenuated by the degree of flexion in the knees. Vibration can have adverse effects on a number of physiologic systems. This work indicates that readily accessible whole body vibration devices markedly exceed ISO guidelines for safety, and extreme caution must be practiced when considering their use. Copyright © 2013 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

23 CFR 630.1004 - Definitions and explanation of terms.

Code of Federal Regulations, 2010 CFR

2010-04-01

... of the work zone design on worker safety. The number of worker fatalities and injuries at a given... activities. A work zone is typically marked by signs, channelizing devices, barriers, pavement markings, and...

23 CFR 630.1004 - Definitions and explanation of terms.

Code of Federal Regulations, 2011 CFR

2011-04-01

... of the work zone design on worker safety. The number of worker fatalities and injuries at a given... activities. A work zone is typically marked by signs, channelizing devices, barriers, pavement markings, and...

23 CFR 630.1004 - Definitions and explanation of terms.

Code of Federal Regulations, 2012 CFR

2012-04-01

... of the work zone design on worker safety. The number of worker fatalities and injuries at a given... activities. A work zone is typically marked by signs, channelizing devices, barriers, pavement markings, and...

23 CFR 630.1004 - Definitions and explanation of terms.

Code of Federal Regulations, 2014 CFR

2014-04-01

... of the work zone design on worker safety. The number of worker fatalities and injuries at a given... activities. A work zone is typically marked by signs, channelizing devices, barriers, pavement markings, and...

23 CFR 630.1004 - Definitions and explanation of terms.

Code of Federal Regulations, 2013 CFR

2013-04-01

... of the work zone design on worker safety. The number of worker fatalities and injuries at a given... activities. A work zone is typically marked by signs, channelizing devices, barriers, pavement markings, and...

Hair mass index obtained by cross-section trichometry: an objective and clinically useful parameter to quantify hair in chemotherapy-induced alopecia.

PubMed

Vleut, Rowena E; van Poppel, Joyce E A M; Dercksen, Marcus W; Peerbooms, Mijke; Houterman, Saskia; Breed, Wim P M

2013-07-01

In order to evaluate the efficacy of scalp cooling for the prevention of chemotherapy-induced alopecia (CIA), it is essential to precisely quantify the amount of hair mass that is present. We wanted to determine if the hair mass index (HMI), obtained by cross-section trichometry (CST), was a suitable parameter for hair mass measurement, and whether or not marking the measurement site on the scalp was necessary. Ten patients receiving chemotherapy were sequentially measured using CST during their treatment. At the same time, they were asked to report severity of hair loss via three subjective parameters: World Health Organization (WHO) grade, visual analog scale (VAS) score, and patients' need to wear wig or head cover. To investigate the need of marking of the measurement area, differences in HMI between a random 2 × 2-cm site (HMI-C) and four surrounding areas (HMI-S4) on the scalp of eight volunteers and eight chemotherapy patients were calculated and compared. Using CTS, hair loss due to CIA was quite measurable and ranged from 13 to 82 %. Reported VAS scores and WHO grades showed an increase in patients in time; 50 % of patients reported the need to wear a wig or head cover. The difference between HMI-S4 and the HMI-C values in all subjects of the marking group was homogeneously distributed between -11 and +10 and was not statistically different between the volunteer and the patient groups (p = 0.465). CST for HMI measurement is a useful mechanical modality for assessing hair loss in CIA patients. It is quantitatively more precise than existing non-mechanical measuring methods. It is recommended when detection of minor changes in hair quantity is required. Marking a fixed sampling area to ensure return to the exact same site is only required when a minor change in pre- and posttreatment HMI values is anticipated and the mid-line locating device is not/cannot be used.

[Transcatheter closure of atrial septal defects in 40 pediatric patients].

PubMed

Deng, Dong-an; Zhu, Xian-yang; Hou, Chuan-ju; Han, Xiu-min; Wang, Qi-guang; Jin, Yan; Quan, Wei; Liu, Yang; Wang, Shu-fan

2003-07-01

To evaluate the clinical efficiency of transcatheter closure of atrial septal defect (ASD) with AGA-Amplatzer occlusion device in pediatric patients. Forty patients with ASD, 16 males, 24 females, at a mean age of 10.2 years (ranged from 3 to 15 years of age) and with a mean weight of 35.8 kg (ranged from 11 to 87 kg) were studied. Six cases were complicated with pulmonary stenosis (PS), 1 was complicated with ventricular tachycardia (VT). Right heart catheterizations were done in 40 patients for measuring the pressures of right ventricle and pulmonary artery. The balloon diameter of ASD was measured using balloon catheter with guiding wire. The diameter of ASD was measured by TTE and/or TEE, ascertaining the location and size of ASD. Amplatzer occlusion device was sized to be equal to or 1 - 2 mm more than the diameter of balloon stretched. All patients had successful implantation of the Amplatzer device. The success rate was 100%. The diameter measured by TTE was 7 - 30 mm (mean 17.12 mm). The diameter measured by TEE was 7 - 32 mm (mean 18.44 mm). The diameter of balloon stretched of ASD was 8 - 34 mm. Of the 40 cases, 6 were complicated with PS and accepted percutaneous balloon valvuloplasty (PBPV). One case was complicated with VT and accepted radiofrequency catheter ablation (RFCA). Neither complication nor residual shunt was found in any of the patients. The patients were recovered and followed up for 3 or 4 days after deployment of the Amplatzer device. Clinical symptom, cardiac murmur, and findings in ECG, echocardiography and X-ray were improved markedly. AGA-Amplatzer occlusion device is safe and efficient in pediatric patients with ASD.

Bolt and nut evaluator

NASA Technical Reports Server (NTRS)

Kerley, James J. (Inventor); Burkhardt, Raymond (Inventor); White, Steven (Inventor)

1994-01-01

A device for testing fasteners such as nuts and bolts is described which consists of a fixed base plate having a number of threaded and unthreaded holes of varying size for receiving the fasteners to be tested, a torque marking paper taped on top the fixed base plate for marking torque-angle indicia, a torque wrench for applying torque to the fasteners being tested, and an indicator for showing the torque applied to the fastener. These elements provide a low cost, nondestructive device for verifying the strength of bolts and nuts.

Development of guidelines for the installation of marked crosswalks.

DOT National Transportation Integrated Search

2004-01-01

The Manual on Uniform Traffic Control Devices (MUTCD) provides little guidance on the installation of marked crosswalks, especially at locations other than intersections, i.e., mid-block locations. Crosswalks have typically been installed and designe...

Vacuum Arc Vapor Deposition Method and Apparatus for Applying Identification Symbols to Substrates

NASA Technical Reports Server (NTRS)

Schramm, Harry F. (Inventor); Roxby, Donald L. (Inventor); Weeks, Jack L. (Inventor)

2002-01-01

An apparatus for applying permanent markings onto products using a Vacuum Arc Vapor Deposition (VAVD) marker by accelerating atoms or molecules from a vaporization source onto a substrate to form human and/or machine-readable part identification marking that can be detected optically or via a sensing device like x-ray, thermal imaging, ultrasound, magneto-optic, micro-power impulse radar, capacitance, or other similar sensing means. The apparatus includes a housing with a nozzle having a marking end. A chamber having an electrode, a vacuum port and a charge is located within the housing. The charge is activated by the electrode in a vacuum environment and deposited onto a substrate at the marking end of the nozzle. The apparatus may be a hand-held device or be disconnected from the handle and mounted to a robot or fixed station.

Lab-on-a-Chip Device for Rapid Measurement of Vitamin D Levels.

PubMed

Peter, Harald; Bistolas, Nikitas; Schumacher, Soeren; Laurisch, Cecilia; Guest, Paul C; Höller, Ulrich; Bier, Frank F

2018-01-01

Lab-on-a-chip assays allow rapid analysis of one or more molecular analytes on an automated user-friendly platform. Here we describe a fully automated assay and readout for measurement of vitamin D levels in less than 15 min using the Fraunhofer in vitro diagnostics platform. Vitamin D (25-hydroxyvitamin D 3 [25(OH)D 3 ]) dilution series in buffer were successfully tested down to 2 ng/mL. This could be applied in the future as an inexpensive point-of-care analysis for patients suffering from a variety of conditions marked by vitamin D deficiencies.

[Benefit Assessment for Examination and Treatment Methods with Medical Devices of High Hisk: Trade-off between Patient Benefit, Evidence and Access].

PubMed

Mühlbacher, Axel C; Juhnke, Christin

2018-03-01

The lately inured § 137 h SGB V aims to assess the benefit of new examination and treatment methods with medical devices of class IIb and III. In the future, the decision on the reimbursement eligibility will be marked by high requirements in terms of documentation of benefits and harm. The objective of benefit assessment is the operationalization of benefit to patients. A comparative determination of benefit enables rational decision by regulatory authorities. The process of benefit assessment should guarantee transparent decision-making, and the underlying medical and health economic fundamentals should be documented. In principle, benefit assessment can be divided into 3 phases: measuring causal effects of an intervention, assessment of the measured effects and decision on reimbursement based on the aggregation of an overall benefit. To address the peculiarities of medical devices in this process, adaptive study designs, MCDA and adaptive benefit assessment provide a sustainable concept for rapid access by patients to innovative treatments of high quality and safety. © Georg Thieme Verlag KG Stuttgart · New York.

7 CFR 56.2 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2011 CFR

2011-01-01

... AGRICULTURAL MARKETING ACT OF 1946 AND THE EGG PRODUCTS INSPECTION ACT (CONTINUED) VOLUNTARY GRADING OF SHELL EGGS Grading of Shell Eggs Definitions § 56.2 Designation of official certificates, memoranda, marks...

[Innovation of characteristic medicinal cupping devices].

PubMed

Li, Jianping; Zhang, Hui; Yang, Jianmei; Xu, Xinchun; Niu, Yanxia; Cai, Jun

2015-08-01

To compare the differences in the characteristic medicinal cupping therapy between the traditional cupping device and the innovated cupping device. Fifty patients of neck and low back pain were selected. The self-comparison was adopted. The cupping therapy was applied to the acupoints located on the left or right side with the traditional cupping device and the innovated cupping device. The cupping sites were centered at bilateral Quyuan (SI 13) and Dachangshu (BL 25). The cups were retained for 10 min. The traditional cupping device was the glass with smooth border, 100mL. The innovated cupping device was the vacuum-sucking cup. The operative time, medicinal leakage, comfort and cupping marks were observed for the two different cupping devices. The operative time with the innovated medicinal cupping device was shorter obviously compared with the traditional one at Quyuan (SI 13) and Dachangshu (BL 25, both P<0. 05). The comfort with the innovated medicinal cupping device was remarkably improved as compared with the traditional one at the two acupoints (both P<0. 05). The medicinal leakage was similar between the two different devices during the cupping operation (both P>0. 05). The cupping marks with the innovated medicinal cupping device were much deeper than those with the traditional one after cupping therapy. The innovated cupping device is more convenent and comfortable in operation during the characteristic medicinal cupping therapy.

9 CFR 381.204 - Marking of poultry products offered for entry; official import inspection marks and devices.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., Import Inspection Division, is on file at the import inspection facility where the inspection is to be... stamping log containing the following information for each lot of product: the date of inspection, the... container marks, and the MP-410 number covering the product to be inspected. The daily stamping log must be...

The Effects of Laser Marking and Symbol Etching on the Fatigue Life of Medical Devices.

PubMed

Ogrodnik, P J; Moorcroft, C I; Wardle, P

2013-01-01

This paper examines the question;" does permanent laser marking affect the mechanical performance of a metallic medical component?" The literature review revealed the surprising fact that very little has been presented or studied even though intuition suggests that its effect could be detrimental to a component's fatigue life. A brief investigation of laser marking suggests that defects greater than 25 μm are possible. A theoretical investigation further suggests that this is unlikely to cause issues with relation to fast fracture but is highly likely to cause fatigue life issues. An experimental investigation confirmed that laser marking reduced the fatigue life of a component. This combination of lines of evidence suggests, strongly, that positioning of laser marking is highly critical and should not be left to chance. It is further suggested that medical device designers, especially those related to orthopaedic implants, should consider the position of laser marking in the design process. They should ensure that it is in an area of low stress amplitude. They should also ensure that they investigate worst-case scenarios when considering the stress environment; this, however, may not be straightforward.

The Effects of Laser Marking and Symbol Etching on the Fatigue Life of Medical Devices

PubMed Central

Ogrodnik, P. J.; Moorcroft, C. I.; Wardle, P.

2013-01-01

This paper examines the question;“ does permanent laser marking affect the mechanical performance of a metallic medical component?” The literature review revealed the surprising fact that very little has been presented or studied even though intuition suggests that its effect could be detrimental to a component's fatigue life. A brief investigation of laser marking suggests that defects greater than 25 μm are possible. A theoretical investigation further suggests that this is unlikely to cause issues with relation to fast fracture but is highly likely to cause fatigue life issues. An experimental investigation confirmed that laser marking reduced the fatigue life of a component. This combination of lines of evidence suggests, strongly, that positioning of laser marking is highly critical and should not be left to chance. It is further suggested that medical device designers, especially those related to orthopaedic implants, should consider the position of laser marking in the design process. They should ensure that it is in an area of low stress amplitude. They should also ensure that they investigate worst-case scenarios when considering the stress environment; this, however, may not be straightforward. PMID:27006919

46 CFR 108.646 - Marking of stowage locations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN... with symbols in accordance with IMO Resolution A.760(18), indicating the devices stowed in that location for that purpose. (b) If more than one device is stowed in that location, the number of devices...

76 FR 46213 - National Standards for Traffic Control Devices; the Manual on Uniform Traffic Control Devices for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-02

... design and application of traffic control devices, this Manual should not be considered a substitute for... retroreflectivity of longitudinal pavement markings. The deadline for comments to that docket has passed and the... the proposed revisions regarding maintaining minimum retroreflectivity of longitudinal pavement...

21 CFR 872.3730 - Pantograph.

Code of Federal Regulations, 2010 CFR

2010-04-01

... lower jaw. (b) Classification. Class I (general controls). The device is exempt from the premarket... intended to be attached to a patient's head to duplicate lower jaw movements to aid in construction of restorative and prosthetic dental devices. A marking pen is attached to the lower jaw component of the device...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fakir, H.; Gaede, S.; Mulligan, M.

Purpose: To design a versatile, nonhomogeneous insert for the dose verification phantom ArcCHECK{sup Trade-Mark-Sign} (Sun Nuclear Corp., FL) and to demonstrate its usefulness for the verification of dose distributions in inhomogeneous media. As an example, we demonstrate it can be used clinically for routine quality assurance of two volumetric modulated arc therapy (VMAT) systems for lung stereotactic body radiation therapy (SBRT): SmartArc{sup Registered-Sign} (Pinnacle{sup 3}, Philips Radiation Oncology Systems, Fitchburg, WI) and RapidArc{sup Registered-Sign} (Eclipse{sup Trade-Mark-Sign }, Varian Medical Systems, Palo Alto, CA). Methods: The cylindrical detector array ArcCHECK{sup Trade-Mark-Sign} has a retractable homogeneous acrylic insert. In this work, wemore » designed and manufactured a customized heterogeneous insert with densities that simulate soft tissue, lung, bone, and air. The insert offers several possible heterogeneity configurations and multiple locations for point dose measurements. SmartArc{sup Registered-Sign} and RapidArc{sup Registered-Sign} plans for lung SBRT were generated and copied to ArcCHECK{sup Trade-Mark-Sign} for each inhomogeneity configuration. Dose delivery was done on a Varian 2100 ix linac. The evaluation of dose distributions was based on gamma analysis of the diode measurements and point doses measurements at different positions near the inhomogeneities. Results: The insert was successfully manufactured and tested with different measurements of VMAT plans. Dose distributions measured with the homogeneous insert showed gamma passing rates similar to our clinical results ({approx}99%) for both treatment-planning systems. Using nonhomogeneous inserts decreased the passing rates by up to 3.6% in the examples studied. Overall, SmartArc{sup Registered-Sign} plans showed better gamma passing rates for nonhomogeneous measurements. The discrepancy between calculated and measured point doses was increased up to 6.5% for the nonhomogeneous insert depending on the inhomogeneity configuration and measurement location. SmartArc{sup Registered-Sign} and RapidArc{sup Registered-Sign} plans had similar plan quality but RapidArc{sup Registered-Sign} plans had significantly higher monitor units (up to 70%). Conclusions: A versatile, nonhomogeneous insert was developed for ArcCHECK{sup Trade-Mark-Sign} for an easy and quick evaluation of dose calculations with nonhomogeneous media and for comparison of different treatment planning systems. The device was tested for SmartArc{sup Registered-Sign} and RapidArc{sup Registered-Sign} plans for lung SBRT, showing the uncertainties of dose calculations with inhomogeneities. The new insert combines the convenience of the ArcCHECK{sup Trade-Mark-Sign} and the possibility of assessing dose distributions in inhomogeneous media.« less

UV lasers for drilling and marking applications.

PubMed

Hannon, T

1999-10-01

Lasers emitting ultraviolet (UV) light have unique capabilities for precision micromachining and marking plastic medical devices. This review of the benefits offered by laser technology includes a look at recently developed UV diode-pumped solid-state lasers and their key features.

23 CFR 924.11 - Implementation.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., where applicable, for highway construction projects, 23 CFR part 172 for engineering and design services..., pavement markings, or installation of traffic signs, traffic lights, guardrails, impact attenuators... may amount up to 100 percent for projects for signing, pavement markings, active warning devices, and...

23 CFR 924.11 - Implementation.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., where applicable, for highway construction projects, 23 CFR part 172 for engineering and design services..., pavement markings, or installation of traffic signs, traffic lights, guardrails, impact attenuators... may amount up to 100 percent for projects for signing, pavement markings, active warning devices, and...

23 CFR 924.11 - Implementation.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., where applicable, for highway construction projects, 23 CFR part 172 for engineering and design services..., pavement markings, or installation of traffic signs, traffic lights, guardrails, impact attenuators... may amount up to 100 percent for projects for signing, pavement markings, active warning devices, and...

23 CFR 924.11 - Implementation.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., where applicable, for highway construction projects, 23 CFR part 172 for engineering and design services..., pavement markings, or installation of traffic signs, traffic lights, guardrails, impact attenuators... may amount up to 100 percent for projects for signing, pavement markings, active warning devices, and...

23 CFR 924.11 - Implementation.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., where applicable, for highway construction projects, 23 CFR part 172 for engineering and design services..., pavement markings, or installation of traffic signs, traffic lights, guardrails, impact attenuators... may amount up to 100 percent for projects for signing, pavement markings, active warning devices, and...

Scalp marking for a craniotomy using a laser pointer during preoperative computed tomographic imaging: technical note.

PubMed

Kubo, S; Nakata, H; Sugauchi, Y; Yokota, N; Yoshimine, T

2000-05-01

The preoperative localization of superficial intracranial lesions is often necessary for accurate burr hole placement or craniotomy siting. It is not always easy, however, to localize the lesions over the scalp working only from computed tomographic images. We developed a simple method for such localization using a laser pointer during the preoperative computed tomographic examination. The angle of incidence, extending from a point on the scalp to the center of the computed tomographic image, is measured by the software included with the scanner. In the gantry, at the same angle as on the image, a laser is beamed from a handmade projector onto the patient's scalp toward the center of the gantry. The point illuminated on the patient's head corresponds to that on the image. The device and the method are described in detail herein. We applied this technique to mark the area for the craniotomy before surgery in five patients with superficial brain tumors. At the time of surgery, it was confirmed that the tumors were circumscribed precisely. The technique is easy to perform and useful in the preoperative planning for a craniotomy. In addition, the device is easily constructed and inexpensive.

Transportation-markings foundations. Part A, volume I, first studies

DOT National Transportation Integrated Search

2008-01-01

This book is about "Transportation-Markings" (hereafter T-M). A T-M can be defined as "any device which aids a mode of transportation (ship, plane, auto, train) by giving guidance, by expressing regulations, or by giving warnings." That includes the ...

Two-treatment protocol for skin laxity using 90-Watt dynamic monopolar radiofrequency device with real-time impedance intelligence monitoring.

PubMed

McDaniel, David; Weiss, Robert; Weiss, Margaret; Mazur, Chris; Griffen, Charmaine

2014-09-01

Multiple devices are currently on the market that employ radiofrequency to non-invasively treat skin laxity and wrinkle reduction. The study device was a unique monopolar radiofrequency device FDA cleared for the treatment of wrinkles and rhytids. The delivery system allows constant monitoring of the real-time local skin impedance changes, which allows radiofrequency energy to be more uniformly dosed over an entire treatment area. The objective was to validate effectiveness of a modified treatment protocol for a unique monopolar radiofrequency device, which has been engineered with greater power and self-monitoring circuitry. Twenty-four female subjects received bilateral monopolar radiofrequency treatments to the mid and lower face from the sub malar region to the submentum. Subjects completed 1 and 3 month follow ups with digital imaging. Skin biopsies (on 4 subjects) and ultrasound measurements (on 12 subjects) were completed. Assessments demonstrated a reduction in skin laxity of 35%, a reduction in fine lines/wrinkles of 42%, and a reduction in the appearance of global photodamage of 33%. Expert photograding demonstrated 92% of subjects showing at least a mild improvement in skin laxity at three months post treatment. 50 MHz ultrasound measurements in 12 subjects showed an increase of 19% in skin density. Histology showed a marked increase in dermal collagen and elastin fibers in two subjects who demonstrated a clinically noticeable reduction in skin laxity and minimal changes in two subjects who demonstrated minimal clinical improvements. There were no significant adverse events reported. This modified radiofrequency device and treatment protocol was well tolerated and produced improvements in the appearance of skin laxity and overall anti-aging effects in the majority of subjects. Objective measurements including ultrasound and histology help explain the clinical outcome.

76 FR 59704 - Agency Information Collection Activities; Proposed Collection; Comment Request; Prominent and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-27

... Mark of Manufacturers on Single-Use Devices AGENCY: Food and Drug Administration, HHS. ACTION: Notice... single-use device labeling. DATES: Submit either electronic or written comments on the collection of... Single-Use Devices (OMB Control Number 0910-0577)--Extension Section 502 of the Federal Food, Drug, and...

Transportation-markings database : traffic control devices. Part I 2, Volume 3, additional studies

DOT National Transportation Integrated Search

1998-01-01

The Database (Part I 1, 2, 3, 4) of transportation-markings: a study in communication monograph series draws together the several varios dimensions of T-M. it shares this drawing togther function with the General Classification (Part H). But, paradox...

FDA, CE mark or something else?-Thinking fast and slow.

PubMed

Mishra, Sundeep

There is a robust debate going on among the Medical Device stake-holders whether FDA is better or CE mark or something else. Currently process of obtaining an FDA approval is bogged down by ever-increasing unpredictability, inconsistency, prolonged time, and huge expense but CE mark has its own problems. Historically, the Japanese review process has tended to be the slowest among the big three but recently with the introduction of accelerated review process there has been a significant progress. While the goal of an innovator/manufacturer is to develop, manufacture and market a medical device that addresses an unmet clinical need, the requisite regulatory approval process can be very confusing. Not only there is a whole lot of jargon tossed around by regulatory affair professionals: "substantial equivalence," "PMDA," "CE mark," "Notified body," "510K" and "PMA" but the actual approval process can also be very tardy, inconsistent and expensive. Copyright © 2016 Cardiological Society of India. Published by Elsevier B.V. All rights reserved.

Noninvasive ultrasonic examination technology in support of counter-terrorism and drug interdiction activities: the acoustic inspection device (AID)

NASA Astrophysics Data System (ADS)

Diaz, Aaron A.; Burghard, Brion J.; Skorpik, James R.; Shepard, Chester L.; Samuel, Todd J.; Pappas, Richard A.

2003-07-01

The Pacific Northwest National Laboratory (PNNL) has developed a portable, battery-operated, handheld ultrasonic device that provides non-invasive container interrogation and material identification capabilities. The technique governing how the acoustic inspection device (AID) functions, involves measurements of ultrasonic pulses (0.1 to 5 MHz) that are launched into a container or material. The return echoes from these pulses are analyzed in terms of time-of-flight and frequency content to extract physical property measurements (the acoustic velocity and attenuation coefficient) of the material under test. The AID performs an automated analysis of the return echoes to identify the material, and detect contraband in the form of submerged packages and concealed compartments in liquid filled containers and solid-form commodities. An inspector can quickly interrogate outwardly innocuous commodity items such as shipping barrels, tanker trucks, and metal ingots. The AID can interrogate container sizes ranging from approximately 6 inches in diameter to over 96 inches in diameter and allows the inspector to sort liquid and material types into groups of like and unlike; a powerful method for discovering corrupted materials or miss-marked containers co-mingled in large shipments. This manuscript describes the functionality, capabilities and measurement methodology of the technology as it relates to homeland security applications.

Microplasma device architectures with various diamond nanostructures

NASA Astrophysics Data System (ADS)

Kunuku, Srinivasu; Jothiramalingam Sankaran, Kamatchi; Leou, Keh-Chyang; Lin, I.-Nan

2017-02-01

Diamond nanostructures (DNSs) were fabricated from three different morphological diamonds, microcrystalline diamond (MCD), nanocrystalline diamond (NCD), and ultrananocrystalline diamond (UNCD) films, using a reactive ion etching method. The plasma illumination (PI) behavior of microplasma devices using the DNSs and the diamond films as cathode were investigated. The Paschen curve approach revealed that the secondary electron emission coefficient (γ value) of diamond materials is similar irrespective of the microstructure (MCD, NCD, and UNCD) and geometry of the materials (DNSs and diamond films). The diamond materials show markedly larger γ-coefficient than conventional metallic cathode materials such as Mo that resulted in markedly better PI behavior for the corresponding microplasma devices. Moreover, the PI behavior, i.e. the voltage dependence of plasma current density (J pl-V), plasma density (n e-V), and the robustness of the devices, varied markedly with the microstructure and geometry of the cathode materials that was closely correlated to the electron field emission (EFE) properties of the cathode materials. The UNCD nanopillars, possessing good EFE properties, resulted in superior PI behavior, whereas the MCD diamond films with insufficient EFE properties led to inferior PI behavior. Consequently, enhancement of plasma characteristics is the collective effects of EFE behavior and secondary electron emission characteristics of diamond-based cathode materials.

Cephalometrically assessing the validity of superior, middle and inferior tragus points on ala-tragus line while establishing the occlusal plane in edentulous patient

PubMed Central

Thombare, Ram

2013-01-01

PURPOSE The purpose of this study was to decide the most appropriate point on tragus to be used as a reference point at time of marking ala tragus line while establishing occlusal plane. MATERIALS AND METHODS The data was collected in two groups of subjects: 1) Dentulous 2) Edentulous group having sample size of 30 for each group with equal gender distribution (15 males, 15 females each). Downs analysis was used for base value. Lateral cephalographs were taken for all selected subjects. Three points were marked on tragus as Superior (S), Middle (M), and Inferior (I) and were joined with ala (A) of the nose to form ala-tragus lines. The angle formed by each line (SA plane, MA plane, IA plane) with Frankfort Horizontal (FH) plane was measured by using custom made device and modified protractor in all dentulous and edentulous subjects. Also, in dentulous subjects angle between Frankfort Horizontal plane and natural occlusal plane was measured. The measurements obtained were subjected to the following statistical tests; descriptive analysis, Student's unpaired t-test and Pearson's correlation coefficient. RESULTS The results demonstrated, the mean angle COO (cant of occlusal plane) as 9.76°, inferior point on tragus had given the mean angular value of IFH [Angle between IA plane (plane formed by joining inferior point-I on tragus and ala of nose- A) and FH plane) as 10.40° and 10.56° in dentulous and edentulous subjects respectively which was the closest value to the angle COO and was comparable with the values of angle COO value in Downs analysis. Angulations of ala-tragus line marked from inferior point with occlusal plane in dentulous subject had given the smallest value 2.46° which showed that this ala-tragus line was nearly parallel to occlusal plane. CONCLUSION The inferior point marked on tragus is the most appropriate point for marking ala-tragus line. PMID:23508068

49 CFR Appendix A to Part 221 - Procedures for Approval of Rear End Marking Devices

Code of Federal Regulations, 2011 CFR

2011-10-01

... description of the device including the type, luminance description, size of lens, manufacturer and catalog number, lamp manufacturer, lamp type and model number, and any auxiliary optics used. (2) A certification...

49 CFR Appendix A to Part 221 - Procedures for Approval of Rear End Marking Devices

Code of Federal Regulations, 2010 CFR

2010-10-01

... description of the device including the type, luminance description, size of lens, manufacturer and catalog number, lamp manufacturer, lamp type and model number, and any auxiliary optics used. (2) A certification...

REMOVAL OF DBCP FROM GROUNDWATER. VOLUME 1. POE/POU TREATMENT DEVICES: INSTITUTIONAL AND JURISDICTIONAL FACTORS

EPA Science Inventory

The results obtained from evaluating ten GAC POE (point-of-entry) devices show that while these GAC units generally function very satisfactorily, their performance can change markedly over short periods of time.

Translocation of single-stranded DNA through single-walled carbon nanotubes.

PubMed

Liu, Haitao; He, Jin; Tang, Jinyao; Liu, Hao; Pang, Pei; Cao, Di; Krstic, Predrag; Joseph, Sony; Lindsay, Stuart; Nuckolls, Colin

2010-01-01

We report the fabrication of devices in which one single-walled carbon nanotube spans a barrier between two fluid reservoirs, enabling direct electrical measurement of ion transport through the tube. A fraction of the tubes pass anomalously high ionic currents. Electrophoretic transport of small single-stranded DNA oligomers through these tubes is marked by large transient increases in ion current and was confirmed by polymerase chain reaction analysis. Each current pulse contains about 10(7) charges, an enormous amplification of the translocated charge. Carbon nanotubes simplify the construction of nanopores, permit new types of electrical measurements, and may open avenues for control of DNA translocation.

A comparative effectiveness analysis of three continuous glucose monitors.

PubMed

Damiano, Edward R; El-Khatib, Firas H; Zheng, Hui; Nathan, David M; Russell, Steven J

2013-02-01

To compare three continuous glucose monitoring (CGM) devices in subjects with type 1 diabetes under closed-loop blood glucose (BG) control. Six subjects with type 1 diabetes (age 52 ± 14 years, diabetes duration 32 ± 14 years) each participated in two 51-h closed-loop BG control experiments in the hospital. Venous plasma glucose (PG) measurements (GlucoScout, International Biomedical) obtained every 15 min (2,360 values) were paired in time with corresponding CGM glucose (CGMG) measurements obtained from three CGM devices, the Navigator (Abbott Diabetes Care), the Seven Plus (DexCom), and the Guardian (Medtronic), worn simultaneously by each subject. Errors in paired PG-CGMG measurements and data reporting percentages were obtained for each CGM device. The Navigator had the best overall accuracy, with an aggregate mean absolute relative difference (MARD) of all paired points of 11.8 ± 11.1% and an average MARD across all 12 experiments of 11.8 ± 3.8%. The Seven Plus and Guardian produced aggregate MARDs of all paired points of 16.5 ± 17.8% and 20.3 ± 18.0%, respectively, and average MARDs across all 12 experiments of 16.5 ± 6.7% and 20.2 ± 6.8%, respectively. Data reporting percentages, a measure of reliability, were 76% for the Seven Plus and nearly 100% for the Navigator and Guardian. A comprehensive head-to-head-to-head comparison of three CGM devices for BG values from 36 to 563 mg/dL revealed marked differences in performance characteristics that include accuracy, precision, and reliability. The Navigator outperformed the other two in these areas.

Electron-beam lithography for micro and nano-optical applications

NASA Technical Reports Server (NTRS)

Wilson, Daniel W.; Muller, Richard E.; Echternach, Pierre M.

2005-01-01

Direct-write electron-beam lithography has proven to be a powerful technique for fabricating a variety of micro- and nano-optical devices. Binary E-beam lithography is the workhorse technique for fabricating optical devices that require complicated precision nano-scale features. We describe a bi-layer resist system and virtual-mark height measurement for improving the reliability of fabricating binary patterns. Analog E-beam lithography is a newer technique that has found significant application in the fabrication of diffractive optical elements. We describe our techniques for fabricating analog surface-relief profiles in E-beam resist, including some discussion regarding overcoming the problems of resist heating and charging. We also describe a multiple-field-size exposure scheme for suppression of field-stitch induced ghost diffraction orders produced by blazed diffraction gratings on non-flat substrates.

Thermoelectric device for treatment of radiculitis and spinal massage

NASA Astrophysics Data System (ADS)

Anatychuk, L. I.; Kobylyansky, R. R.

2012-06-01

Results of development of a thermoelectric device that enables controlled cyclic temperature impact on the damaged area of human organism are presented. Unlike the existing medical devices employing direct supply current for thermoelectric module, the present device controls supply current according to time dependence of temperature change assigned by doctor. It is established that such a device is an efficient means of therapy at herniation of intervertebral disks with marked radiculitis and tunicary syndromes, at meningitis, other spinal diseases and back traumas.

A Comparative Field Study of Permastripe(Trademark) Polymer Concrete and Waterborne Airfield Pavement Markings

DTIC Science & Technology

2007-06-01

mounted to a self-propelled lawn mower (Figure 4). This resulted in acceptable Permastripe™ line thickness (25 to 30 mils). However, bead embedment...Permastripe™ markings were sprayed using a modified drywall texture application device mounted on a modified self-propelled lawn mower (Figure 4). This

Surface EMG and intra-socket force measurement to control a prosthetic device

NASA Astrophysics Data System (ADS)

Sanford, Joe; Patterson, Rita; Popa, Dan

2015-06-01

Surface electromyography (SEMG) has been shown to be a robust and reliable interaction method allowing for basic control of powered prosthetic devices. Research has shown a marked decrease in EMG-classification efficiency throughout activities of daily life due to socket shift and movement and fatigue as well as changes in degree of fit of the socket throughout the subject's lifetime. Users with the most severe levels of amputation require the most complex devices with the greatest number of degrees of freedom. Controlling complex dexterous devices with limited available inputs requires the addition of sensing and interaction modalities. However, the larger the amputation severity, the fewer viable SEMG sites are available as control inputs. Previous work reported the use of intra-socket pressure, as measured during wrist flexion and extension, and has shown that it is possible to control a powered prosthetic device with pressure sensors. In this paper, we present data correlations of SEMG data with intra-socket pressure data. Surface EMG sensors and force sensors were housed within a simulated prosthetic cuff fit to a healthy-limbed subject. EMG and intra-socket force data was collected from inside the cuff as a subject performed pre-defined grip motions with their dominant hand. Data fusion algorithms were explored and allowed a subject to use both intra-socket pressure and SEMG data as control inputs for a powered prosthetic device. This additional input modality allows for an improvement in input classification as well as information regarding socket fit through out activities of daily life.

The Laparosound{trade mark, serif}-an ultrasonic morcellator for use in laparoscopic surgery

NASA Astrophysics Data System (ADS)

Malinowski, Igor; Łobodzinski, Suave S.; Paśniczek, Roman

2012-05-01

The laparoscopic surgery has gained presence in the operating room in cases where it is feasible to spare patient trauma and minimize the hospital stay. One unique challenge in laparoscopic/endoscopic surgery is operating and removing tissue volume through keyhole - trocar. The removal of tissues by fragmentation is generally termed morcellation. We proposed a new method for soft tissue morcellation using laparoscopy. A unique ultrasonic laparoscopic surgical device, termed Laparosound{trade mark, serif}, utilizing laparoscopic high amplitude ultrasonic waveguides, operating in edge mode, has been developed that uses the principle of ultrasonic cavitation phenomenon for excision and morcellation of a variety of tissue types. The local ultrasonic acoustic intensity at the distal waveguide tip is sufficiently high that the liquefaction of moist tissue occurs. The mechanism of tissue morcellation is deemed to be cavitation based, therefore is dependant on water content in tissue, and thus its effectiveness depends on tissue type. This results in ultrasound being efficient in moist tissue and sparing dry, collagen rich blood vessels and thus minimizes bleeding. The applications of such device in particular, commonly encountered, could lay in general and ob/gyn laparoscopic surgery, whereas other applications could emerge. The design of power ultrasonic instruments for mass clinical applications poses however unique challenges, such as ability to design and build ultrasonic resonators that last in conditions of ultrasonic fatigue. These highly non-linear devices, whose behavior is hard to predict, have become the challenge of the author of the present paper. The object of work is to design and build an operating device capable of ultrasonic soft tissue morcellation in laparoscopic surgery. This includes heavy computational ultrasonics verified by testing and manufacturing feasibility using titanium biomedical alloys. The prototype Laparosound{trade mark, serif} device has been built and tested. Some of the challenges in design and development of Laparosound{trade mark, serif} ultrasonic laparoscopic morcellator have been presented.

Advanced public transportation systems deployment in the United States

DOT National Transportation Integrated Search

2003-01-01

Traffic control devices shall be defined as all signs, signals, markings, and other devices used to regulate, warn, or guide traffic, placed on, over, or adjacent to a street, highway, pedestrian facility, or bikeway by authority of a public agency h...

Device fabrication, characterization, and thermal neutron detection response of LiZnP and LiZnAs semiconductor devices

NASA Astrophysics Data System (ADS)

Montag, Benjamin W.; Ugorowski, Philip B.; Nelson, Kyle A.; Edwards, Nathaniel S.; McGregor, Douglas S.

2016-11-01

Nowotny-Juza compounds continue to be explored as candidates for solid-state neutron detectors. Such a device would have greater efficiency, in a compact form, than present day gas-filled 3He and 10BF3 detectors. The 6Li(n,t)4He reaction yields a total Q-value of 4.78 MeV, larger than 10B, an energy easily identified above background radiations. Hence, devices fabricated from semiconductor compounds having either natural Li (nominally 7.5% 6Li) or enriched 6Li (usually 95% 6Li) as constituent atoms may provide a material for compact high efficiency neutron detectors. Starting material was synthesized by preparing equimolar portions of Li, Zn, and As sealed under vacuum (10-6 Torr) in quartz ampoules lined with boron nitride and subsequently reacted in a compounding furnace [1]. The raw synthesized material indicated the presence high impurity levels (material and electrical property characterizations). A static vacuum sublimation in quartz was performed to help purify the synthesized material [2,3]. Bulk crystalline samples were grown from the purified material [4,5]. Samples were cut using a diamond wire saw, and processed into devices. Bulk resistivity was determined from I-V curve measurements, ranging from 106-1011 Ω cm. Devices were characterized for sensitivity to 5.48 MeV alpha particles, 337 nm laser light, and neutron sensitivity in a thermal neutron diffracted beam at the Kansas State University TRIGA Mark II nuclear reactor. Thermal neutron reaction product charge induction was measured with a LiZnP device, and the reaction product spectral response was observed.

Characterization and Modeling of High Power Microwave Effects in CMOS Microelectronics

DTIC Science & Technology

2010-01-01

margin measurement 28 Any voltage above the line marked VIH is considered a valid logic high on the input of the gate. VIH and VIL are defined...can handle any voltage noise level at the input up to VIL without changing state. The region in between VIL and VIH is considered an invalid logic...29 Table 2.2: Intrinsic device characteristics derived from SPETCRE simulations   VIH  (V)  VIL (V)  High Noise Margin  (V)  Low Noise Margin (V

7 CFR 28.176 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2010 CFR

2010-01-01

..., other identifications, and devices for purpose of the Agricultural Marketing Act. 28.176 Section 28.176 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE COMMODITY STANDARDS AND STANDARD CONTAINER...

Marking Ground Targets With Radio Transmitters Dropped From Aircraft

Treesearch

Thomas H. Nichols; Michael E. Ostry; Mark R. Fuller

1981-01-01

Reports development and use of a radio transmitter device that can be dropped from aircraft into target areas in remote habitats. Such a device could be a valuable tool for studying and managing forests and wildlife, for controlling forest fires, and for handling emergencies.

Usability of Optical Mark Reader Sheet as an Answering Tool in Testing.

PubMed

Booka, Masayuki; Oku, Hidehisa; Scheller, Andreas; Yamaoka, Shintaro

2017-01-01

The research result on usability of Optical Mark Reader Sheet (OMRS) being used as the standard answering tool is reported. The use of OMRS significantly requires more answer time than the answer time without OMRS, and the use of assistive devices for OMRS has the possibility to reduce the answer time.

76 FR 54738 - Proposed Information Collection; Comment Request; Atlantic Highly Migratory Species Vessel and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-02

... Collection; Comment Request; Atlantic Highly Migratory Species Vessel and Gear Marking AGENCY: National... vessel numbers on their vessels. Flotation devices and high- flyers attached to certain fishing gears must also be marked with the vessel's number to identify the vessel to which the gear belongs. These...

Measurement of Interfacial Profiles of Wavy Film Flow on Inclined Wall

NASA Astrophysics Data System (ADS)

Rosli, N.; Amagai, K.

2016-02-01

Falling liquid films on inclined wall present in many industrial processes such as in food processing, seawater desalination and electronic devices manufacturing industries. In order to ensure an optimal efficiency of the operation in these industries, a fundamental study on the interfacial flow profiles of the liquid film is of great importance. However, it is generally difficult to experimentally predict the interfacial profiles of liquid film flow on inclined wall due to the instable wavy flow that usually formed on the liquid film surface. In this paper, the liquid film surface velocity was measured by using a non-intrusive technique called as photochromic dye marking method. This technique utilizes the color change of liquid containing the photochromic dye when exposed to the UV light source. The movement of liquid film surface marked by the UV light was analyzed together with the wave passing over the liquid. As a result, the liquid film surface was found to slightly shrink its gradual movement when approached by the wave before gradually move again after the intersection with the wave.

Localization of needle tip with color doppler during pericardiocentesis: In vitro validation and initial clinical application

NASA Technical Reports Server (NTRS)

Armstrong, G.; Cardon, L.; Vilkomerson, D.; Lipson, D.; Wong, J.; Rodriguez, L. L.; Thomas, J. D.; Griffin, B. P.

2001-01-01

This study evaluates a new device that uses color Doppler ultrasonography to enable real-time image guidance of the aspirating needle, which has not been possible until now. The ColorMark device (EchoCath Inc, Princeton, NJ) induces high-frequency, low-amplitude vibrations in the needle to enable localization with color Doppler. We studied this technique in 25 consecutive patients undergoing pericardiocentesis, and in vitro, in a urethane phantom with which the accuracy of color Doppler localization of the needle tip was compared with that obtained by direct measurement. Tip localization was excellent in vitro; errors axial to the ultrasound beam (velocity Doppler -0.13 +/- 0.90 mm, power Doppler -0.05 +/- 1.7 mm) were less than lateral errors (velocity -0.36 +/- 1.8 mm, power -0.02 +/- 2.8 mm). In 18 of 25 patients, the needle was identified and guided into the pericardial space with the ColorMark technique, and it allowed successful, uncomplicated drainage of fluid. Initial failures were the result of incorrect settings on the echocardiographic machine and inappropriate combinations of the needle puncture site and imaging window. This study demonstrates a novel color Doppler technique that is highly accurate at localizing a needle tip. The technique is feasible for guiding pericardiocentesis. Further clinical validation of this technique is required.

Beginning the 21st century with advanced Automatic Parts Identification (API)

NASA Technical Reports Server (NTRS)

Schramm, Fred; Roxby, Don

1994-01-01

Under the direction of the NASA George C. Marshall Space Flight Center, Huntsville, Alabama, the development and commercialization of an advanced Automated Parts Indentification (API) system is being undertaken by Rockwell International Corporation. The new API system is based on a variable sized, machine-readable, two-dimensioanl matrix symbol that can be applied directly onto most metallic and nonmetallic materials using safe, permanent marking methods. Its checkerboard-like structure is the most space efficient of all symbologies. This high data-density symbology can be applied to products of different material sizes and geometries using application-dependent, computer-driven marking devices. The high fidelity markings produced by these devices can then be captured using a specially designed camera linked to any IBM-compatible computer. Applications of compressed symbology technology will reduce costs and improve quality, productivity, and processes in a wide variety of federal and commercial applications.

Successful development of first-generation laser device; marking China's optoelectronic technology at world class level

NASA Astrophysics Data System (ADS)

1995-04-01

Bell Laboratories has developed the world's first optical information processor. Its core device is a self-excited electrooptical effect apparatus array of symmetric operation. After being developed in the United States, this high-technology device was successfully developed by China's scientists,thus making the fact that China's optoelectronic technology is among the most advanced in the world.

An examination of coherent structures in a lobed mixer using multifractal measures in conjunction with the proper orthogonal decomposition

NASA Technical Reports Server (NTRS)

Ukeiley, L.; Varghese, M.; Glauser, M.; Valentine, D.

1991-01-01

A 'lobed mixer' device that enhances mixing through secondary flows and streamwise vorticity is presently studied within the framework of multifractal-measures theory, in order to deepen understanding of velocity time trace data gathered on its operation. Proper orthogonal decomposition-based knowledge of coherent structures has been applied to obtain the generalized fractal dimensions and multifractal spectrum of several proper eigenmodes for data samples of the velocity time traces; this constitutes a marked departure from previous multifractal theory applications to self-similar cascades. In certain cases, a single dimension may suffice to capture the entire spectrum of scaling exponents for the velocity time trace.

7 CFR 52.3 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2010 CFR

2010-01-01

..., other identifications, and devices for purposes of the Agricultural Marketing Act. 52.3 Section 52.3 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL...

7 CFR 70.2 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2010 CFR

2010-01-01

..., other identifications, and devices for purposes of the Agricultural Marketing Act. 70.2 Section 70.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) REGULATIONS AND STANDARDS UNDER THE...

7 CFR 51.3 - Designation of official certificates, memoranda, marks, other identifications and devices for...

Code of Federal Regulations, 2010 CFR

2010-01-01

..., other identifications and devices for purposes of the Agricultural Marketing Act. 51.3 Section 51.3 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL...

Effects of electrostatic discharge on three cryogenic temperature sensor models

NASA Astrophysics Data System (ADS)

Courts, S. Scott; Mott, Thomas B.

2014-01-01

Cryogenic temperature sensors are not usually thought of as electrostatic discharge (ESD) sensitive devices. However, the most common cryogenic thermometers in use today are thermally sensitive diodes or resistors - both electronic devices in their base form. As such, they are sensitive to ESD at some level above which either catastrophic or latent damage can occur. Instituting an ESD program for safe handling and installation of the sensor is costly and it is desirable to balance the risk of ESD damage against this cost. However, this risk cannot be evaluated without specific knowledge of the ESD vulnerability of the devices in question. This work examines three types of cryogenic temperature sensors for ESD sensitivity - silicon diodes, Cernox{trade mark, serif} resistors, and wire wound platinum resistors, all manufactured by Lake Shore Cryotronics, Inc. Testing was performed per TIA/EIA FOTP129 (Human Body Model). Damage was found to occur in the silicon diode sensors at discharge levels of 1,500 V. For Cernox{trade mark, serif} temperature sensors, damage was observed at 3,500 V. The platinum temperature sensors were not damaged by ESD exposure levels of 9,900 V. At the lower damage limit, both the silicon diode and the Cernox{trade mark, serif} temperature sensors showed relatively small calibration shifts of 1 to 3 K at room temperature. The diode sensors were stable with time and thermal cycling, but the long term stability of the Cernox{trade mark, serif} sensors was degraded. Catastrophic failure occurred at higher levels of ESD exposure.

46 CFR 108.643 - Rudder orders.

Code of Federal Regulations, 2010 CFR

2010-10-01

... GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT... the wheel or steering device must be moved for right rudder or left rudder must be marked in letters of contrasting color to the background on the wheel or steering device or in a place that is directly...

Recommendations for yield-to-bus traffic control devices and bus pullout bays design characteristics.

DOT National Transportation Integrated Search

2013-04-01

Traffic control devices such as roadside signs and pavement markings are used to promote highway safety and efficiency for all road users. A bus pullout bay is a special geometric roadway feature that allows transit buses to stop outside the travel l...

Need and use of assistive devices for personal mobility by individuals with spinal cord injury

PubMed Central

Florio, Jordanne; Arnet, Ursina; Gemperli, Armin; Hinrichs, Timo

2016-01-01

Objective To investigate the provision, use, and unmet need of assistive devices for personal mobility in the Swiss population with spinal cord injury (SCI). Design Community survey 2012 of the Swiss Spinal Cord Injury Cohort Study. Participants Individuals aged 16 or older with traumatic or non-traumatic SCI residing in Switzerland. Interventions Not applicable. Outcome Measures Provision, frequency of use, and unmet need (i.e. perceiving the need of a device but it not being provided) of 11 mobility devices were assessed by self-report and analyzed descriptively. Provision of devices was further analyzed by sex, age, SCI etiology, SCI severity, and time since SCI. Results Devices reported highest for provision (N = 492; mean age 55.3 ± 15.1 years; 28.9% female) were adapted cars (78.2%) and manual wheelchairs (69.9%). Provision of various devices markedly varied with age and SCI severity (e.g. 34.6% of those aged 76+ had a walking frame compared to 3.1% of those aged 31–45; 50.0% of participants with complete tetraplegia had a power wheelchair compared to 7.6% of those with complete paraplegia). Many devices were mostly used daily (e.g. manual wheelchair) while others were mostly used less frequently (e.g. handbikes). Unmet need was highest for arm braces (53.2% of those in need) and power assisted wheelchairs (47.3%), and lowest for crutches (11.4%) and manual wheelchairs (4.8%). Conclusion The devices individuals have or use is largely dependent on their age and SCI severity. While most participants have access to basic mobility devices, there is still a considerable degree of unmet need for certain devices. PMID:26666510

Sensor fusion: lane marking detection and autonomous intelligent cruise control system

NASA Astrophysics Data System (ADS)

Baret, Marc; Baillarin, S.; Calesse, C.; Martin, Lionel

1995-12-01

In the past few years MATRA and RENAULT have developed an Autonomous Intelligent Cruise Control (AICC) system based on a LIDAR sensor. This sensor incorporating a charge coupled device was designed to acquire pulsed laser diode emission reflected by standard car reflectors. The absence of moving mechanical parts, the large field of view, the high measurement rate and the very good accuracy for distance range and angular position of targets make this sensor very interesting. It provides the equipped car with the distance and the relative speed of other vehicles enabling the safety distance to be controlled by acting on the throttle and the automatic gear box. Experiments in various real traffic situations have shown the limitations of this kind of system especially on bends. All AICC sensors are unable to distinguish between a bend and a change of lane. This is easily understood if we consider a road without lane markings. This fact has led MATRA to improve its AICC system by providing the lane marking information. Also in the scope of the EUREKA PROMETHEUS project, MATRA and RENAULT have developed a lane keeping system in order to warn of the drivers lack of vigilance. Thus, MATRA have spread this system to far field lane marking detection and have coupled it with the AICC system. Experiments will be carried out on roads to estimate the gain in performance and comfort due to this fusion.

14 CFR 25.699 - Lift and drag device indicator.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Control Systems § 25... each lift or drag device having a separate control in the cockpit to adjust its position. In addition... controls must be clearly marked to identify this range of extension. [Amdt. 25-23, 35 FR 5675, Apr. 8, 1970] ...

14 CFR 25.699 - Lift and drag device indicator.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Control Systems § 25... each lift or drag device having a separate control in the cockpit to adjust its position. In addition... controls must be clearly marked to identify this range of extension. [Amdt. 25-23, 35 FR 5675, Apr. 8, 1970] ...

14 CFR 25.699 - Lift and drag device indicator.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Control Systems § 25... each lift or drag device having a separate control in the cockpit to adjust its position. In addition... controls must be clearly marked to identify this range of extension. [Amdt. 25-23, 35 FR 5675, Apr. 8, 1970] ...

76 FR 25696 - Guidance for Industry on Dosage Delivery Devices for Orally Ingested OTC Liquid Drug Products...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-05

... are manufacturing, marketing, or distributing orally ingested over-the-counter (OTC) liquid drug... overdoses that can result from the use of dosage delivery devices with markings that are inconsistent or... because of ongoing concerns about potentially serious accidental drug overdoses that can result from the...

Travel in Adverse Weather Using Electronic Mobility Guidance Devices

ERIC Educational Resources Information Center

Farmer, Leicester W.

1975-01-01

After a discussion of the required characteristics of an ideal aid for blind individuals traveling in adverse weather, four electronic mobility guidance devices- the Mowat Sonar Sensor, the Russell E Model Pathsounder, the Bionic C-5 Laser Cane, and the Mark II Binaural Sensory Aid-are described in detail. (Author/SB)

33 CFR 149.135 - What should be marked on the cargo transfer system alarm switch?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false What should be marked on the cargo transfer system alarm switch? 149.135 Section 149.135 Navigation and Navigable Waters COAST GUARD... switch? Each switch for activating an alarm, and each audio or visual device for signaling an alarm, must...

33 CFR 149.135 - What should be marked on the cargo transfer system alarm switch?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false What should be marked on the cargo transfer system alarm switch? 149.135 Section 149.135 Navigation and Navigable Waters COAST GUARD... switch? Each switch for activating an alarm, and each audio or visual device for signaling an alarm, must...

33 CFR 149.135 - What should be marked on the cargo transfer system alarm switch?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false What should be marked on the cargo transfer system alarm switch? 149.135 Section 149.135 Navigation and Navigable Waters COAST GUARD... switch? Each switch for activating an alarm, and each audio or visual device for signaling an alarm, must...

33 CFR 149.135 - What should be marked on the cargo transfer system alarm switch?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false What should be marked on the cargo transfer system alarm switch? 149.135 Section 149.135 Navigation and Navigable Waters COAST GUARD... switch? Each switch for activating an alarm, and each audio or visual device for signaling an alarm, must...

33 CFR 149.135 - What should be marked on the cargo transfer system alarm switch?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false What should be marked on the cargo transfer system alarm switch? 149.135 Section 149.135 Navigation and Navigable Waters COAST GUARD... switch? Each switch for activating an alarm, and each audio or visual device for signaling an alarm, must...

9 CFR 75.4 - Interstate movement of equine infectious anemia reactors and approval of laboratories, diagnostic...

Code of Federal Regulations, 2010 CFR

2010-01-01

...: (1) The description, including age, breed, color, sex, and distinctive markings when present (such as... self-locking device on one end and a slot on the other end, which forms a loop when the ends are..., including name, age, sex, breed, color, and markings. Reactor. Any horse, ass, mule, pony or zebra which is...

29 CFR 1917.50 - Certification of marine terminal material handling devices (See also mandatory appendix I, of...

Code of Federal Regulations, 2014 CFR

2014-07-01

... beams or other house fall block supports shall be marked with the safe working load, which shall not be... depends upon components other than commonly used stock items such as shackles, ropes, or chains, and that... (c)(6) of this section). Single sheave blocks shall be marked with safe working loads and proof test...

29 CFR 1917.50 - Certification of marine terminal material handling devices (See also mandatory appendix I, of...

Code of Federal Regulations, 2011 CFR

2011-07-01

... beams or other house fall block supports shall be marked with the safe working load, which shall not be... depends upon components other than commonly used stock items such as shackles, ropes, or chains, and that... (c)(6) of this section). Single sheave blocks shall be marked with safe working loads and proof test...

29 CFR 1917.50 - Certification of marine terminal material handling devices (See also mandatory appendix I, of...

Code of Federal Regulations, 2010 CFR

2010-07-01

... beams or other house fall block supports shall be marked with the safe working load, which shall not be... depends upon components other than commonly used stock items such as shackles, ropes, or chains, and that... (c)(6) of this section). Single sheave blocks shall be marked with safe working loads and proof test...

29 CFR 1917.50 - Certification of marine terminal material handling devices (See also mandatory appendix I, of...

Code of Federal Regulations, 2013 CFR

2013-07-01

... beams or other house fall block supports shall be marked with the safe working load, which shall not be... depends upon components other than commonly used stock items such as shackles, ropes, or chains, and that... (c)(6) of this section). Single sheave blocks shall be marked with safe working loads and proof test...

29 CFR 1917.50 - Certification of marine terminal material handling devices (See also mandatory appendix I, of...

Code of Federal Regulations, 2012 CFR

2012-07-01

... beams or other house fall block supports shall be marked with the safe working load, which shall not be... depends upon components other than commonly used stock items such as shackles, ropes, or chains, and that... (c)(6) of this section). Single sheave blocks shall be marked with safe working loads and proof test...

Optical Docking Aid Containing Fresnel Lenses

NASA Technical Reports Server (NTRS)

Pierce, Cole J.

1995-01-01

Proposed device provides self-contained visual cues to aid in docking. Similar to devices used to guide pilots in landing on aircraft carriers. Positions and directions of beams of light give observer visual cues of position relative to docking target point. Optical assemblies generate directed, diverging beams of light that, together, mark approach path to docking point. Conceived for use in docking spacecraft at Space Station Freedom, device adapted to numerous industrial docking and alignment applications.

Third-order nonlinear electro-optic measurements in the smectic-? phase

NASA Astrophysics Data System (ADS)

Nowicka, Kamila; Bielejewska, Natalia

2018-02-01

The chiral smectic subphase with three-layer structure, ?, is now of great interest from the point of view of device technologies such as multistate or symmetric switching. We report that the unique nonlinear electro-optic response can serve as precise mark of the phase transition into three-layer structure. The problem is illustrated with the first and third harmonic electro-optic spectra. Furthermore, the characteristic response of the helical liquid crystal phases correlated with particular collective modes using the Debye-type relaxation method for the well-known prototype liquid crystal material (MHPOBC) are presented.

Low G accelerometer testing

NASA Technical Reports Server (NTRS)

Vaughan, M. S.

1972-01-01

Eight different types of low-g accelerometer tests are covered on the Bell miniature electrostatically suspended accelerometer (MESA) which is known to be sensitive to less than 10 to the minus 7th power earth's gravity. These tests include a mass attracting scheme, Leitz dividing head, Wild theodolite, precision gage blocks, precision tiltmeters, Hilger Watts autocollimator, Razdow Mark 2 autocollimator, and laser interferometer measuring system. Each test is described and a comparison of the results is presented. The output of the MESA was as linear and consistent as any of the available devices were capable of measuring. Although the extent of agreement varied with the test equipment used, it can only be concluded that the indicated errors were attributable to the test equipment coupled with the environmental conditions.

[Three cases of the malignant esophageal stenosis successfully treated with the Niti-S™ esophageal stent].

PubMed

Isohata, Noriyuki; Naritaka, Yoshihiko; Asaka, Shinichi; Shimakawa, Takeshi; Miyaki, Akira; Yamaguchi, Kentaro; Murayama, Minoru; Katsube, Takao; Ogawa, Kenji

2011-11-01

We herein report three cases of the malignant esophageal stenosis successfully treated with the Niti-S™ esophageal stent. CASE 1: The hilar lung cancer and its mediastinal lymph node metastasis pressed the esophagus extramurally and caused the marked stenosis. CASE 2: A metastatic lymph node along the left laryngeal nerve caused the stenosis of the trachea. A primary esophageal lesion located at the middle thoracic esophagus also caused the marked stenosis. At first, tracheal stent was placed because of dyspnea, and two weeks later, we placed an esophageal stent. Case 3: Esophageal cancer at lower thoracic esophagus after definitive radiation therapy caused the marked stenosis. Because of the stenosis of esophago-gastric junction( EGJ), we used an esophageal stent with a long cover in order to prevent a reflux into the esophagus. This new Niti-STM esophageal stent was easy to place at the stenosis without difficulty using a conventional device. The symptom was improved immediately for each case. We hope this new device will be used widely.

Impedance analysis of PbS colloidal quantum dot solar cells with different ZnO nanowire lengths

NASA Astrophysics Data System (ADS)

Fukuda, Takeshi; Takahashi, Akihiro; Wang, Haibin; Takahira, Kazuya; Kubo, Takaya; Segawa, Hiroshi

2018-03-01

The photoconversion efficiency of colloidal quantum dot (QD) solar cells has been markedly improved by optimizing the surface passivation and device structure, and details of device physics are now under investigation. In this study, we investigated the resistance and capacitance components at the ZnO/PbS-QD interface and inside a PbS-QD layer by measuring the impedance spectrum while the interface area was controlled by changing the ZnO nanowire length. By evaluating the dependence of optical intensity and DC bias voltage on the ZnO nanowire length, only the capacitance was observed to be influenced by the interface area, and this indicates that photoinduced carriers are generated at the surface of PbS-QD. In addition, since the capacitance is proportional to the surface area of the QD, the interface area can be evaluated from the capacitance. Finally, photovoltaic performance was observed to increase with increasing ZnO nanowire length owing to the large interface area, and this result is in good agreement with the capacitance measurement.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Faye, Mbaye; Bordessoule, Michel; Kanouté, Brahim

When using bright, small effective size sources, such as synchrotron radiation light beam, for broadband spectroscopy at spectral or spatial high resolution for mid-IR FTIR measurements, a marked detectivity improvement can be achieved by setting up a device matching the detector optical étendue to that of the source. Further improvement can be achieved by reducing the background unmodulated flux and other intrinsic noise sources using a lower temperature cryogen, such as liquid helium. By the combined use of cooled apertures, cold reimaging optics, filters and adapted detector polarization, and preamplification electronics, the sensitivity of a HgCdTe photoconductive IR detector canmore » be improved by a significant factor with respect to standard commercial devices (more than one order of magnitude on average over 6–20 μm region) and the usable spectral range extended to longer wavelengths. The performances of such an optimized detector developed on the AILES Beamline at SOLEIL are presented here.« less

Robotics in the rehabilitation treatment of patients with stroke.

PubMed

Volpe, Bruce T; Ferraro, Mark; Krebs, Hermano I; Hogan, Neville

2002-07-01

Stroke is the leading cause of permanent disability despite continued advances in prevention and novel interventional treatments. Post-stroke neuro-rehabilitation programs teach compensatory strategies that alter the degree of permanent disability. Robotic devices are new tools for therapists to deliver enhanced sensorimotor training and concentrate on impairment reduction. Results from several groups have registered success in reducing impairment and increasing motor power with task-specific exercise delivered by the robotic devices. Enhancing the rehabilitation experience with task-specific repetitive exercise marks a different approach to the patient with stroke. The clinical challenge will be to streamline, adapt, and expand the robot protocols to accommodate healthcare economies, to determine which patients sustain the greatest benefit, and to explore the relationship between impairment reduction and disability level. With these new tools, therapists will measure aspects of outcome objectively and contribute to the emerging scientific basis of neuro-rehabilitation.

In vitro performance of DIAGNOdent laser fluorescence device for dental calculus detection on human tooth root surfaces.

PubMed

Rams, Thomas E; Alwaqyan, Abdulaziz Y

2017-10-01

This study assessed the reproducibility of a red diode laser device, and its capability to detect dental calculus in vitro on human tooth root surfaces. On each of 50 extracted teeth, a calculus-positive and calculus-free root surface was evaluated by two independent examiners with a low-power indium gallium arsenide phosphide diode laser (DIAGNOdent) fitted with a periodontal probe-like sapphire tip and emitting visible red light at 655 nm wavelength. Laser autofluorescence intensity readings of examined root surfaces were scored on a 0-99 scale, with duplicate assessments performed using the laser probe tip directed both perpendicular and parallel to evaluated tooth root surfaces. Pearson correlation coefficients of untransformed measurements, and kappa analysis of data dichotomized with a >40 autofluorescence intensity threshold, were calculated to assess intra- and inter-examiner reproducibility of the laser device. Mean autofluorescence intensity scores of calculus-positive and calculus-free root surfaces were evaluated with the Student's t -test. Excellent intra- and inter-examiner reproducibility was found for DIAGNOdent laser autofluorescence intensity measurements, with Pearson correlation coefficients above 94%, and kappa values ranging between 0.96 and 1.0, for duplicate readings taken with both laser probe tip orientations. Significantly higher autofluorescence intensity values were measured when the laser probe tip was directed perpendicular, rather than parallel, to tooth root surfaces. However, calculus-positive roots, particularly with calculus in markedly-raised ledges, yielded significantly greater mean DIAGNOdent laser autofluorescence intensity scores than calculus-free surfaces, regardless of probe tip orientation. DIAGNOdent autofluorescence intensity values >40 exhibited a stronger association with calculus (36.6 odds ratio) then measurements of ≥5 (20.1 odds ratio) when the laser probe tip was advanced parallel to root surfaces. Excellent intra- and inter-examiner reproducibility of autofluorescence intensity measurements was obtained with the DIAGNOdent laser fluorescence device on human tooth roots. Calculus-positive root surfaces exhibited significantly greater DIAGNOdent laser autofluorescence than calculus-free tooth roots, even with the laser probe tip directed parallel to root surfaces. These findings provide further in vitro validation of the potential utility of a DIAGNOdent laser fluorescence device for identifying dental calculus on human tooth root surfaces.

Wavefront holoscopy: application of digital in-line holography for the inspection of engraved marks in progressive addition lenses.

PubMed

Perucho, Beatriz; Micó, Vicente

2014-01-01

Progressive addition lenses (PALs) are engraved with permanent marks at standardized locations in order to guarantee correct centering and alignment throughout the manufacturing and mounting processes. Out of the production line, engraved marks provide useful information about the PAL as well as act as locator marks to re-ink again the removable marks. Even though those marks should be visible by simple visual inspection with the naked eye, engraving marks are often faint and weak, obscured by scratches, and partially occluded and difficult to recognize on tinted or antireflection-coated lenses. Here, we present an extremely simple optical device (named as wavefront holoscope) for visualization and characterization of permanent marks in PAL based on digital in-line holography. Essentially, a point source of coherent light illuminates the engraved mark placed just before a CCD camera that records a classical Gabor in-line hologram. The recorded hologram is then digitally processed to provide a set of high-contrast images of the engraved marks. Experimental results are presented showing the applicability of the proposed method as a new ophthalmic instrument for visualization and characterization of engraved marks in PALs.

Multispectral cross-polarization reflectance measurements suggest high contrast of demineralization on tooth surfaces at wavelengths beyond 1300 nm due to reduced light scattering in sound enamel.

PubMed

Chan, Kenneth H; Fried, Daniel

2018-06-01

The enamel scattering coefficient decreases markedly with increasing wavelength from the visible to the near-infrared (NIR). However, beyond 1300 nm, the scattering coefficient is difficult to measure, and it is not known whether light scattering continues to decrease significantly at longer wavelengths. It is hypothesized that water absorption is a major contributor to the contrast between sound and demineralized enamel beyond 1300 nm since deeply penetrating photons in sound enamel are likely absorbed by water. Reflectance images of demineralization on tooth surfaces were acquired at wavelengths near 1450, 1860, 1880, and 1950 nm. The magnitude of water absorption is similar at 1450 and 1880 nm but varies markedly between 1860, 1880, and 1950 nm. Multispectral comparisons of lesion contrast provide insight into the mechanism responsible for higher contrast at longer NIR wavelengths. The highest contrast was at 1950 nm; however, the markedly higher contrast at 1880 compared to 1450 nm and similar contrast between 1860 and 1880 nm suggests that the enamel scattering coefficient continues to decrease beyond 1300 nm, and that reduced light scattering in sound enamel is most responsible for the higher lesion contrast at longer NIR wavelengths. This has important implications for the choice of wavelengths for caries detection and diagnostic devices, including the performance of optical coherence tomography beyond 1300 nm. (2018) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blankenship, H.Lee; Thompson, Dan; United States. Bonneville Power Administration. Division of Fish and Wildlife

The first year of work with development of lasers as a mass marking technique provided both disappointing and encouraging results. A Coumarin Dye 480 laser was used to mark coho salmon in a variety of body locations and with varying energy levels. A ``bleached`` white mark was made void of any pigment. Areas marked included the nape area behind the head and in front of the dorsal fin, slightly above the anal fin, the upper lobe of the caudal fin, the dorsal fin and on the operculum. The mark appeared immediately after being lasered but started to gradually fade aftermore » one month and was fairly completely re-pigmented after three months. Complete removal and notching of the adipose fin was also attempted with a Carbon Dioxide laser. This surgical method of fin removal appears to have advantages over scissor excision (no bleeding or regeneration), and has possible application as part of a device or system which could be employed for mass marking.« less

Hydrogel Ring for Topical Drug Delivery to the Ocular Posterior Segment.

PubMed

Shikamura, Yuko; Yamazaki, Yoshiko; Matsunaga, Toru; Sato, Takao; Ohtori, Akira; Tojo, Kakuji

2016-05-01

To investigate the efficacy of a topical hydrogel ring for drug delivery to the posterior segment of the rabbit eye. Novel hydrogel corneal lenses (CL), scleral/corneal lenses (S/CL), and rings were prepared using poly(hydroxyethyl methacrylate). The devices were immersed in 0.3% ofloxacin ophthalmic solution (OOS) to homogeneously distribute the drug throughout the hydrogel. The medicated CL, S/CL, Ring 1 (standard ring), or Ring 2 (shape-optimized ring) was applied to the surface of the cornea, cornea/bulbar conjunctiva, or bulbar conjunctiva of albino rabbits, respectively. Medicated rings did not touch the corneal surface. In another group, one OOS drop was administered to the eye. After 0.25-8 hours, the hydrogel devices were removed and ocular tissues were harvested. High-performance liquid chromatography (HPLC) was used to measure the ofloxacin concentration in the devices and tissues. The drug concentrations in the posterior segment tissues were compared among ofloxacin delivery methods. One hour after placement, eyes treated with Ring 1 or S/CL had markedly higher ofloxacin levels in the posterior segment tissues (conjunctiva, sclera, and retina/choroid) than eyes treated with topical OOS or a CL. Lower levels of ofloxacin were found in anterior segment tissues (cornea and aqueous humor) in eyes treated with Ring 1 compared to those treated with S/CL. Ring 2 most effectively delivered ofloxacin to the retina/choroid. The tissue ofloxacin concentration in the fellow eye was markedly lower than the eye treated with Ring 2. Our results suggest that hydrogel rings are effective in delivering topical ophthalmic drugs to the posterior segment. The drugs are most likely delivered via the transconjunctival/scleral route by lateral diffusion across the bulbar conjunctiva and through the sclera. Systemic drug delivery to the posterior segment is minimal.

A Stroboscopic Light Source for Experiments in Mechanics

ERIC Educational Resources Information Center

Mayer, V. V.; Varaksina, E. I.

2017-01-01

We propose to attach a small stroboscopic light source to a moving object and connect the source to a pulse generator with the help of insulated thin flexible multi-cored wires. Students can assemble such a device independently in a school laboratory. The device can be used to obtain trajectories with time marks in students' research projects in…

77 FR 35471 - National Environmental Policy Act Implementation

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-13

... designed to promote transportation safety, security, accessibility, communication or operational efficiency... surface treatments or pavement markings, small passenger shelters, railroad warning devices, train control...

Integrated optics implementation of a fiber optic rotation sensor - Analysis and development. [for Mariner Mark II planetary explorer

NASA Technical Reports Server (NTRS)

Bartman, R. K.; Youmans, B. R.; Nerheim, N. M.

1987-01-01

The Jet Propulsion Laboratory is developing a fiber optic rotation sensor (FORS) for use on the Mariner Mark II series of planetary explorer craft and in other space applications. FORS is a closed-loop phase-nulling device and embodies a number of interesting innovations. Chief among these are the incorporation of the device's couplers, phase modulators, and polarizer on a single lithium niobate (LinbO3) integrate optics chip and a novel means of reading out angular position and rotation rate based on optical beat detection. Various aspects of the FORS design and operation are described and discussed. Particular attention is paid to analyzing errors attributable to polarizer imperfection and the so-called residual Michelson effect.

Development and evaluation of the Nurotron 26-electrode cochlear implant system.

PubMed

Zeng, Fan-Gang; Rebscher, Stephen J; Fu, Qian-Jie; Chen, Hongbin; Sun, Xiaoan; Yin, Li; Ping, Lichuan; Feng, Haihong; Yang, Shiming; Gong, Shusheng; Yang, Beibei; Kang, Hou-Yong; Gao, Na; Chi, Fanglu

2015-04-01

Although the cochlear implant has been widely acknowledged as the most successful neural prosthesis, only a fraction of hearing-impaired people who can potentially benefit from a cochlear implant have actually received one due to its limited awareness, accessibility, and affordability. To help overcome these limitations, a 26-electrode cochlear implant has been developed to receive China's Food and Drug Administration (CFDA) approval in 2011 and Conformité Européenne (CE) Marking in 2012. The present article describes design philosophy, system specification, and technical verification of the Nurotron device, which includes advanced digital signal processing and 4 current sources with multiple amplitude resolutions that not only are compatible with perceptual capability but also allow interleaved or simultaneous stimulation. The article also presents 3-year longitudinal evaluation data from 60 human subjects who have received the Nurotron device. The objective measures show that electrode impedance decreased within the first month of device use, but was stable until a slight increase at the end of two years. The subjective loudness measures show that electric stimulation threshold was stable while the maximal comfort level increased over the 3 years. Mandarin sentence recognition increased from the pre-surgical 0%-correct score to a plateau of about 80% correct with 6-month use of the device. Both indirect and direct comparisons indicate indistinguishable performance differences between the Nurotron system and other commercially available devices. The present 26-electrode cochlear implant has already helped to lower the price of cochlear implantation in China and will likely contribute to increased cochlear implant access and success in the rest of the world. This article is part of a Special Issue entitled . Copyright © 2014 The Authors. Published by Elsevier B.V. All rights reserved.

Lumbar Spinal Stenosis Minimally Invasive Treatment with Bilateral Transpedicular Facet Augmentation System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Masala, Salvatore, E-mail: salva.masala@tiscali.it; Tarantino, Umberto; Nano, Giovanni, E-mail: gionano@gmail.com

Purpose. The purpose of this study was to evaluate the effectiveness of a new pedicle screw-based posterior dynamic stabilization device PDS Percudyn System Trade-Mark-Sign Anchor and Stabilizer (Interventional Spine Inc., Irvine, CA) as alternative minimally invasive treatment for patients with lumbar spine stenosis. Methods. Twenty-four consecutive patients (8 women, 16 men; mean age 61.8 yr) with lumbar spinal stenosis underwent implantation of the minimally invasive pedicle screw-based device for posterior dynamic stabilization. Inclusion criteria were lumbar stenosis without signs of instability, resistant to conservative treatment, and eligible to traditional surgical posterior decompression. Results. Twenty patients (83 %) progressively improved duringmore » the 1-year follow-up. Four (17 %) patients did not show any improvement and opted for surgical posterior decompression. For both responder and nonresponder patients, no device-related complications were reported. Conclusions. Minimally invasive PDS Percudyn System Trade-Mark-Sign has effectively improved the clinical setting of 83 % of highly selected patients treated, delaying the need for traditional surgical therapy.« less

Sarcasm and emoticons: Comprehension and emotional impact.

PubMed

Filik, Ruth; Țurcan, Alexandra; Thompson, Dominic; Harvey, Nicole; Davies, Harriet; Turner, Amelia

2016-11-01

Most theorists agree that sarcasm serves some communicative function that would not be achieved by speaking directly, such as eliciting a particular emotional response in the recipient. One debate concerns whether this kind of language serves to enhance or mute the positive or negative nature of a message. The role of textual devices commonly used to accompany written sarcastic remarks is also unclear. The current research uses a rating task to investigate the influence of textual devices (emoticons and punctuation marks) on the comprehension of, and emotional responses to, sarcastic versus literal criticism and praise, for both unambiguous (Experiment 1) and ambiguous (Experiment 2) materials. Results showed that sarcastic criticism was rated as less negative than literal criticism, and sarcastic praise was rated as less positive than literal praise, suggesting that sarcasm serves to mute the positive or negative nature of the message. In terms of textual devices, results showed that emoticons had a larger influence on both comprehension and emotional impact than punctuation marks.

Optimal micro-mirror tilt angle and sync mark design for digital micro-mirror device based collinear holographic data storage system.

PubMed

Liu, Jinpeng; Horimai, Hideyoshi; Lin, Xiao; Liu, Jinyan; Huang, Yong; Tan, Xiaodi

2017-06-01

The collinear holographic data storage system (CHDSS) is a very promising storage system due to its large storage capacities and high transfer rates in the era of big data. The digital micro-mirror device (DMD) as a spatial light modulator is the key device of the CHDSS due to its high speed, high precision, and broadband working range. To improve the system stability and performance, an optimal micro-mirror tilt angle was theoretically calculated and experimentally confirmed by analyzing the relationship between the tilt angle of the micro-mirror on the DMD and the power profiles of diffraction patterns of the DMD at the Fourier plane. In addition, we proposed a novel chess board sync mark design in the data page to reduce the system bit error rate in circumstances of reduced aperture required to decrease noise and median exposure amount. It will provide practical guidance for future DMD based CHDSS development.

Self-propelled in-tube shuttle and control system for automated measurements of magnetic field alignment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boroski, W.N.; Nicol, T.H.; Pidcoe, S.V.

1990-03-01

A magnetic field alignment gauge is used to measure the field angle as a function of axial position in each of the magnets for the Superconducting Super Collider (SSC). Present measurements are made by manually pushing the through the magnet bore tube and stopping at intervals to record field measurements. Gauge location is controlled through graduation marks and alignment pins on the push rods. Field measurements are recorded on a logging multimeter with tape output. Described is a computerized control system being developed to replace the manual procedure for field alignment measurements. The automated system employs a pneumatic walking devicemore » to move the measurement gauge through the bore tube. Movement of the device, called the Self-Propelled In-Tube Shuttle (SPITS), is accomplished through an integral, gas driven, double-acting cylinder. The motion of the SPITS is transferred to the bore tube by means of a pair of controlled, retractable support feet. Control of the SPITS is accomplished through an RS-422 interface from an IBM-compatible computer to a series of solenoid-actuated air valves. Direction of SPITS travel is determined by the air-valve sequence, and is managed through the control software. Precise axial position of the gauge within the magnet is returned to the control system through an optically-encoded digital position transducer attached to the shuttle. Discussed is the performance of the transport device and control system during preliminary testing of the first prototype shuttle. 1 ref., 7 figs.« less

Cataract, cost: curious questions.

PubMed

Moran, D J

1999-02-01

An investigation of the pricing of implantable prosthetic devices in Australia reveals some alarming practices. A governmental mechanism exists to prop up the pricing of 7500 listed devices to levels that are unacceptably high by world standards. Private hospitals and doctors are able, legally, to profit by marking up the cost of these devices from the market price to this artificially inflated price. Even the open market prices of implantable prosthetic items, such as intra-ocular lenses, are high by international standards. In a time of budgetary constraint for health spending and rapidly increasing use of these devices, these issues urgently need to be addressed in Australia.

Distance Estimation Using Handheld Devices

DTIC Science & Technology

2013-06-01

each and all centered in the pin that marks the location of the device. ................................47 Figure 21. Form interface where the UFO ...SIFT Scale-invariant feature transform SURF Speed up Robust Features SAD Sum of Absolute Distance UFOs Untrained Forward Observers WHATWG Web...Forward Observers ( UFOs ) to make a successful call for fire. This chapter presents the solution from different aspects and is organized as follows

Trial of a novel endoscopic tattooing biopsy forceps on animal model

PubMed Central

Si, Jian-Min; Sun, Lei-Min; Fan, Yu-Jing; Wang, Liang-Jing

2005-01-01

AIM: To tattoo gastric mucosa with a novel medical device which could be used to monitor and follow-up gastric mucosal lesions. METHODS: Combining endoscopic biopsy with sclerotherapy injection, we designed a new device that could perform biopsy and injection simultaneously. We performed endoscopies on a pig by using a novel endoscope tattoo biopsy forceps for 15 mo. At the same time, we used two-step method combining sclerotherapy injection needle with endoscopic biopsy. The acuity, inflammation and duration of endoscopy were compared between two methods. RESULTS: Compared with the old two-step method, although the inflammation induced by our new device was similar, the duration of procedure was markedly decreased and the acuity of tattooing was better than the old two-step method. All characteristics of the novel device complied with national safety guidelines. Follow-up gastroscopy after 15 mo showed the stained site with injection of 1:100 0.5 mL of India ink was still markedly visible with little inflammatory reaction. CONCLUSION: Endoscopic tattooing biopsy forceps can be widely used in monitoring precancerous lesions. Its safety and effectiveness has been established in animals. PMID:15793881

[Bellows or bag? Testing 10 ventilators and some medical history comments].

PubMed

Kötter, K P; Maleck, W H; Altmannsberger, S; Herchet, J; Petroianu, G A

1998-01-01

We compared a new bellows ventilator (Kendall Cardiovent) with two other bellows (Dräger Resutator 63, Tagg Breathsaver) and seven bag or ball ventilators (Aerodyne Hope, Ambu Mark 3, Ambu Silicon, Dräger Resutator 2000, Laerdal Resu, Mercury CPR, Weinmann Combibag). Tidal volumes were measured with two Laerdal Recording Resusci Annies, one lying on the floor, one in a bed. Twelve participants performed mask ventilation with all ten devices on both manikins for two minutes, trying to achieve tidal volumes of between 0.8 and 1.21 as recommended by the AHA. The last ten ventilations each on the graphic strips were analysed for volume. The participants scored handling of the devices on a 6-point scale (1 = very good, 6 = insufficient). The results of the Cardiovent were compared to those of the other devices by rank sum test (percentage of correct ventilations) and sign test (subjective handling). The Cardiovent provided exact ventilation with 95% of ventilations) on the floor and 78% of ventilations in bed in the recommended range. However, the percentage of correct ventilations with the Cardiovent was not significantly different to the other devices except for a lower percentage of correct ventilations with the Combibag in the in bed setting. Concerning subjective handling, the Cardiovent was significantly superior to several ball ventilators.

Polymer/Nanocrystal Hybrid Solar Cells: Influence of Molecular Precursor Design on Film Nanomorphology, Charge Generation and Device Performance

PubMed Central

MacLachlan, Andrew J; Rath, Thomas; Cappel, Ute B; Dowland, Simon A; Amenitsch, Heinz; Knall, Astrid-Caroline; Buchmaier, Christine; Trimmel, Gregor; Nelson, Jenny; Haque, Saif A

2015-01-01

In this work, molecular tuning of metal xanthate precursors is shown to have a marked effect on the heterojunction morphology of hybrid poly(3-hexylthiophene-2,5-diyl) (P3HT)/CdS blends and, as a result, the photochemical processes and overall performance of in situ fabricated hybrid solar cells. A series of cadmium xanthate complexes is synthesized for use as in situ precursors to cadmium sulfide nanoparticles in hybrid P3HT/CdS solar cells. The formation of CdS domains is studied by simultaneous GIWAXS (grazing incidence wide-angle X-ray scattering) and GISAXS (grazing incidence small-angle X-ray scattering), revealing knowledge about crystal growth and the formation of different morphologies observed using TEM (transmission electron microscopy). These measurements show that there is a strong relationship between precursor structure and heterojunction nanomorphology. A combination of TAS (transient absorption spectroscopy) and photovoltaic device performance measurements is used to show the intricate balance required between charge photogeneration and percolated domains in order to effectively extract charges to maximize device power conversion efficiencies. This study presents a strong case for xanthate complexes as a useful route to designing optimal heterojunction morphologies for use in the emerging field of hybrid organic/inorganic solar cells, due to the fact that the nanomorphology can be tuned via careful design of these precursor materials. PMID:25866496

Subjective and objective outcomes from new BiCROS technology in a veteran sample.

PubMed

Williams, Victoria A; McArdle, Rachel A; Chisolm, Theresa H

2012-01-01

Patients with single-sided deafness (SSD), where one ear has an unaidable hearing loss and the other ear has normal or aidable hearing, often complain of difficulties understanding speech and localizing sound sources, and report a higher self-perceived hearing disability. Patients with SSD may benefit from using contralateral routing of signal (CROS) or bilateral contralateral routing of the signal (BiCROS) amplification. Dissatisfaction of previously available (Bi)CROS devices has been reported, such as, interfering transmissions, low-fidelity sound quality, poor "user-friendly" set-up, and a bulky and cosmetically cumbersome appearance. Recent advances in hearing aid technology have improved (Bi)CROS hearing aids; however, these devices have not been experimentally evaluated. We hypothesized that newer technology with reports of improved digital signal processing, wireless transmission, and physical design would be as good, or better than, our participants' previous-generation BiCROS systems. A within-subjects, pretest-posttest design was executed. Thirty-nine veterans (one female, 38 males; mean age = 74 yr, range = 49-85 yr) from the Audiology Section of the Bay Pines Veterans Affair Healthcare System participated. All participants were previously experienced BiCROS hearing aid users with varying degrees of sensorinerual hearing impairment in their better ear. Participants were provided at least 4 wk of consistent use with the new BiCROS. DATA COLLECTION AND ANALYSES: Participants completed three research visits. At Visit 1, with their previous BiCROS, and at Visit 3, with their new BiCROS, the following objective and subjective measures were obtained: (1) soundfield speech-in-noise testing using the Words-In-Noise (WIN) test; (2) speech, spatial, and qualities of the hearing scale (SSQ) questionnaire; (3) selected questions from the MarkeTrak questionnaire; and, (4) three open-ended questions. Data were analyzed using parametric and nonparametric statistics. Overall, the objective (WIN) and subjective (SSQ, MarkeTrak, and open-ended questions) measures indicated that the new BiCROS provided better outcomes than the previous BiCROS system. In addition, an overlap of favorable results was seen across measures. Of the 39 participants, 95% reported improvements with the new BiCROS and chose to utilize the device regularly. The favorable objective and subjective outcomes indicate that the new BiCROS system is as good, or better than, what was previously utilized by our sample of veterans. American Academy of Audiology.

A portable extensional rheometer for measuring the viscoelasticity of pitcher plant and other sticky liquids in the field.

PubMed

Collett, Catherine; Ardron, Alia; Bauer, Ulrike; Chapman, Gary; Chaudan, Elodie; Hallmark, Bart; Pratt, Lee; Torres-Perez, Maria Dolores; Wilson, D Ian

2015-01-01

Biological fluids often have interesting and unusual physical properties to adapt them for their specific purpose. Laboratory-based rheometers can be used to characterise the viscoelastic properties of such fluids. This, however, can be challenging as samples often do not retain their natural properties in storage while conventional rheometers are fragile and expensive devices ill-suited for field measurements. We present a portable, low-cost extensional rheometer designed specifically to enable in situ studies of biological fluids in the field. The design of the device (named Seymour) is based on a conventional capillary break-up extensional rheometer (the Cambridge Trimaster). It works by rapidly stretching a small fluid sample between two metal pistons. A battery-operated solenoid switch triggers the pistons to move apart rapidly and a compact, robust and inexpensive, USB 3 high speed camera is used to record the thinning and break-up of the fluid filament that forms between the pistons. The complete setup runs independently of mains electricity supply and weighs approximately 1 kg. Post-processing and analysis of the recorded images to extract rheological parameters is performed using open source software. The device was tested both in the laboratory and in the field, in Brunei Darussalam, using calibration fluids (silicone oil and carboxymethyl cellulose solutions) as well as Nepenthes pitcher plant trapping fluids as an example of a viscoelastic biological fluid. The fluid relaxation times ranged from 1 ms to over 1 s. The device gave comparable performance to the Cambridge Trimaster. Differences in fluid viscoelasticity between three species were quantified, as well as the change in viscoelasticity with storage time. This, together with marked differences between N. rafflesiana fluids taken from greenhouse and wild plants, confirms the need for a portable device. Proof of concept of the portable rheometer was demonstrated. Quantitative measurements of pitcher plant fluid viscoelasticity were made in the natural habitat for the first time. The device opens up opportunities for studying a wide range of plant fluids and secretions, under varying experimental conditions, or with changing temperatures and weather conditions.

Comparative healing of rat fascia following incision with three surgical instruments.

PubMed

Chang, Edward I; Carlson, Grace A; Vose, Joshua G; Huang, Eric J; Yang, George P

2011-05-01

Incisional hernia and fascial dehiscence are associated with significant postoperative morbidity. Electrosurgical devices using pulsed radiofrequency energy and a novel electrode design markedly reduce thermal injury during cutting and coagulation while maintaining equal surgical performance. In this study, we examine fascial healing dynamics in a rat model following incision with a pulsed radiofrequency energy device (PRE), a conventional electrosurgical device, and a standard "cold" scalpel. We hypothesize that incisions made with the pulsed radiofrequency energy device will result in a superior fascial healing profile compared with conventional electrosurgery. Full thickness surgical incisions were created in rat fascia using a commercially available PRE device, conventional electrosurgery, and a scalpel. Harvested fascial specimens were analyzed for burst strength testing and healing-associated histologic characteristics at d 7, 14, 21, and 42. PRE incisions were fully healed by 6 wk with normal tissue architecture. By all measures, wounds created by the PRE device were comparable to those made with the standard scalpel. Compared with PRE, conventional electrosurgery incisions exhibited a larger zone of tissue injury (68% greater in Coag mode, P < 0.0001; 46% greater in Cut mode, P < 0.001), an increased inflammatory response and a less favorable wound architecture. In the immediate postoperative period (1 wk), burst strength testing demonstrated that PRE fascial wounds were significantly stronger than those made by electrosurgery in Coag mode (318%, P = 0.001). The favorable fascial healing profile of the PRE device suggests that it is a promising new surgical technology. The early improved strength of wounds made with this device is of particular interest, as wound dehiscence is of greatest concern early in the healing process. Published by Elsevier Inc.

29 CFR 1926.154 - Temporary heating devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., unless otherwise permitted by the manufacturer's markings. (d) Solid fuel salamanders. Solid fuel salamanders are prohibited in buildings and on scaffolds. (e) Oil-fired heaters. (1) Flammable liquid-fired...

29 CFR 1926.154 - Temporary heating devices.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., unless otherwise permitted by the manufacturer's markings. (d) Solid fuel salamanders. Solid fuel salamanders are prohibited in buildings and on scaffolds. (e) Oil-fired heaters. (1) Flammable liquid-fired...

I-line stepper based overlay evaluation method for wafer bonding applications

NASA Astrophysics Data System (ADS)

Kulse, P.; Sasai, K.; Schulz, K.; Wietstruck, M.

2018-03-01

In the last decades the semiconductor technology has been driven by Moore's law leading to high performance CMOS technologies with feature sizes of less than 10 nm [1]. It has been pointed out that not only scaling but also the integration of novel components and technology modules into CMOS/BiCMOS technologies is becoming more attractive to realize smart and miniaturized systems [2]. Driven by new applications in the area of communication, health and automation, new components and technology modules such as BiCMOS embedded RF-MEMS, high-Q passives, Sibased microfluidics and InP-SiGe BiCMOS heterointegration have been demonstrated [3-6]. In contrast to standard VLSI processes fabricated on front side of the silicon wafer, these new technology modules additionally require to process the backside of the wafer; thus require an accurate alignment between the front and backside of the wafer. In previous work an advanced back to front side alignment technique and implementation into IHP's 0.25/0.13 µm high performance SiGe:C BiCMOS backside process module has been presented [7]. The developed technique enables a high resolution and accurate lithography on the backside of BiCMOS wafer for additional backside processing. In addition to the aforementioned back side process technologies, new applications like Through-Silicon Vias (TSV) for interposers and advanced substrate technologies for 3D heterogeneous integration demand not only single wafer fabrication but also processing of wafer stacks provided by temporary and permanent wafer bonding [8-9]. In this work, the non-contact infrared alignment system of the Nikon® i-line Stepper NSR-SF150 for both alignment and the overlay determination of bonded wafer stacks with embedded alignment marks are used to achieve an accurate alignment between the different wafer sides. The embedded field image alignment (FIA) marks of the interface and the device wafer top layer are measured in a single measurement job. By taking the offsets between all different FIA's into account, after correcting the wafer rotation induced FIA position errors, hence an overlay for the stacked wafers can be determined. The developed approach has been validated by a standard front side resist in resist experiment. After the successful validation of the developed technique, special wafer stacks with FIA alignment marks in the bonding interface are fabricated and exposed. Following overlay calculation shows an overlay of less than 200 nm, which enables very accurate process condition for highly scaled TSV integration and advanced substrate integration into IHP's 0.25/0.13 µm SiGe:C BiCMOS technology. The developed technique also allows using significantly smaller alignment marks (i.e. standard FIA alignment marks). Furthermore, the presented method is used, in case of wafer bow related overlay tool problems, for the overlay evaluation of the last two metal layers from production wafers prepared in IHP's standard 0.25/0.13 µm SiGe:C BiCMOS technology. In conclusion, the exposure and measurement job can be done with the same tool, minimizing the back to front side/interface top layer misalignment which leads to a significant device performance improvement of backside/TSV integrated components and technologies.

Going Digital - The Transition from Mark IV to DBBC at Onsala

NASA Astrophysics Data System (ADS)

Kareinen, Niko; Haas, Rüdiger; La Porta, Laura; Bertarini, Alessandra

2014-12-01

The Onsala Space Observatory is currently equipped with both a VLBI Mark IV rack and a digital BBC (DBBC). The Mark IV rack at Onsala has been used operationally for both astronomical and geodetic VLBI for more than 40 years. In 2011, Onsala purchased a DBBC and we started to test it and to gain experience with the new device, both for astronomical and geodetic VLBI. The DBBC was upgraded several times and the Field System (FS) interface was implemented. We did parallel recordings, with both the old Mark IV/Mark 5A system and the new DBBC/Mark 5B+ system, during numerous geodetic VLBI sessions. Several R1, T2, and Euro sessions were correlated during the last two years by the Bonn correlator with Onsala being included both as an analog station (two-letter code On) and as a digital station (two-letter code Od). We present results from these parallel sessions, both results from the original correlation and results from the analysis of the corresponding databases.

Communicating about quantity without a language model: number devices in homesign grammar.

PubMed

Coppola, Marie; Spaepen, Elizabet; Goldin-Meadow, Susan

2013-01-01

All natural languages have formal devices for communicating about number, be they lexical (e.g., two, many) or grammatical (e.g., plural markings on nouns and/or verbs). Here we ask whether linguistic devices for number arise in communication systems that have not been handed down from generation to generation. We examined deaf individuals who had not been exposed to a usable model of conventional language (signed or spoken), but had nevertheless developed their own gestures, called homesigns, to communicate. Study 1 examined four adult homesigners and a hearing communication partner for each homesigner. The adult homesigners produced two main types of number gestures: gestures that enumerated sets (cardinal number marking), and gestures that signaled one vs. more than one (non-cardinal number marking). Both types of gestures resembled, in form and function, number signs in established sign languages and, as such, were fully integrated into each homesigner's gesture system and, in this sense, linguistic. The number gestures produced by the homesigners' hearing communication partners displayed some, but not all, of the homesigners' linguistic patterns. To better understand the origins of the patterns displayed by the adult homesigners, Study 2 examined a child homesigner and his hearing mother, and found that the child's number gestures displayed all of the properties found in the adult homesigners' gestures, but his mother's gestures did not. The findings suggest that number gestures and their linguistic use can appear relatively early in homesign development, and that hearing communication partners are not likely to be the source of homesigners' linguistic expressions of non-cardinal number. Linguistic devices for number thus appear to be so fundamental to language that they can arise in the absence of conventional linguistic input. Copyright © 2013 Elsevier Inc. All rights reserved.

Communicating about quantity without a language model: Number devices in homesign grammar

PubMed Central

Coppola, Marie; Spaepen, Elizabet; Goldin-Meadow, Susan

2013-01-01

All natural languages have formal devices for communicating about number, be they lexical (e.g., two, many) or grammatical (e.g., plural markings on nouns and/or verbs). Here we ask whether linguistic devices for number arise in communication systems that have not been handed down from generation to generation. We examined deaf individuals who had not been exposed to a usable model of conventional language (signed or spoken), but had nevertheless developed their own gestures, called homesigns, to communicate. Study 1 examined four adult homesigners and a hearing communication partner for each homesigner. The adult homesigners produced two main types of number gestures: gestures that enumerated sets (cardinal number marking), and gestures that signaled one vs. more than one (non-cardinal number marking). Both types of gestures resembled, in form and function, number signs in established sign languages and, as such, were fully integrated into each homesigner's gesture system and, in this sense, linguistic. The number gestures produced by the homesigners’ hearing communication partners displayed some, but not all, of the homesigners’ linguistic patterns. To better understand the origins of the patterns displayed by the adult homesigners, Study 2 examined a child homesigner and his hearing mother, and found that the child's number gestures displayed all of the properties found in the adult homesigners’ gestures, but his mother's gestures did not. The findings suggest that number gestures and their linguistic use can appear relatively early in homesign development, and that hearing communication partners are not likely to be the source of homesigners’ linguistic expressions of non-cardinal number. Linguistic devices for number thus appear to be so fundamental to language that they can arise in the absence of conventional linguistic input. PMID:23872365

Advanced laser-based tracking device for motor vehicle lane position monitoring and steering assistance

NASA Astrophysics Data System (ADS)

Bachalo, William D.; Inenaga, Andrew; Schuler, Carlos A.

1995-12-01

Aerometrics is developing an innovative laser-diode based device that provides a warning signal when a motor-vehicle deviates from the center of the lane. The device is based on a sensor that scans the roadway on either side of the vehicle and determines the lateral position relative to the existing painted lines marking the lane. No additional markings are required. A warning is used to alert the driver of excessive weaving or unanticipated departure from the center of the lane. The laser beams are at invisible wavelengths to that operation of the device does not pose a distraction to the driver or other motorists: When appropriate markers are not present on the road, the device is capable of detecting this condition and warn the driver. The sensor system is expected to work well irrespective of ambient light levels, fog and rain. This sensor has enormous commercial potential. It could be marketed as an instrument to warn drivers that they are weaving, used as a research tool to monitor driving patterns, be required equipment for those previously convicted of driving under the influence, or used as a backup sensor for vehicle lateral position control. It can also be used in storage plants to guide robotic delivery vehicles. In this paper, the principles of operation of the sensor, and the results of Aerometrics ongoing testing will be presented.

Use and Complications of Operative Control of Arterial Inflow in Combat Casualties with Traumatic Lower-extremity Amputations Caused by Improvised Explosive Devices

DTIC Science & Technology

2013-08-01

explosive devices Henrietta Poon, MRCS, Jonathan J. Morrison, MRCS, Jon C. Clasper, DPhil, FRCSEd(Orth), Mark J. Midwinter, MD, FRCS, and Jan O. Jansen...the IP group, compared with the EP, although this does not achieve statistical significance, likely owing to a lack of power within the study. The war

Monolithic Silicon Microbolometer Materials forUncooled Infrared Detectors

DTIC Science & Technology

2015-05-21

L. Allara, Mark W. Horn. Vanadium Oxide Thin Films Alloyed with Ti, Zr , Nb , and Mo for Uncooled Infrared Imaging Applications, Journal of...entitled "Thin Film Materials and Devices for Resistive Temperature Sensing Applications" by Hitesh Basantani and the other entitled "Reactive...extension. One was entitled "Thin Film Materials and Devices for Resistive Temperature Sensing Applications" by Hitesh Basantani and the other

Mark Tracking: Position/orientation measurements using 4-circle mark and its tracking experiments

NASA Technical Reports Server (NTRS)

Kanda, Shinji; Okabayashi, Keijyu; Maruyama, Tsugito; Uchiyama, Takashi

1994-01-01

Future space robots require position and orientation tracking with visual feedback control to track and capture floating objects and satellites. We developed a four-circle mark that is useful for this purpose. With this mark, four geometric center positions as feature points can be extracted from the mark by simple image processing. We also developed a position and orientation measurement method that uses the four feature points in our mark. The mark gave good enough image measurement accuracy to let space robots approach and contact objects. A visual feedback control system using this mark enabled a robot arm to track a target object accurately. The control system was able to tolerate a time delay of 2 seconds.

Preparation of Janus Particles and Alternating Current Electrokinetic Measurements with a Rapidly Fabricated Indium Tin Oxide Electrode Array.

PubMed

Chen, Yu-Liang; Jiang, Hong-Ren

2017-06-23

This article provides a simple method to prepare partially or fully coated metallic particles and to perform the rapid fabrication of electrode arrays, which can facilitate electrical experiments in microfluidic devices. Janus particles are asymmetric particles that contain two different surface properties on their two sides. To prepare Janus particles, a monolayer of silica particles is prepared by a drying process. Gold (Au) is deposited on one side of each particle using a sputtering device. The fully coated metallic particles are completed after the second coating process. To analyze the electrical surface properties of Janus particles, alternating current (AC) electrokinetic measurements, such as dielectrophoresis (DEP) and electrorotation (EROT)- which require specifically designed electrode arrays in the experimental device- are performed. However, traditional methods to fabricate electrode arrays, such as the photolithographic technique, require a series of complicated procedures. Here, we introduce a flexible method to fabricate a designed electrode array. An indium tin oxide (ITO) glass is patterned by a fiber laser marking machine (1,064 nm, 20 W, 90 to 120 ns pulse-width, and 20 to 80 kHz pulse repetition frequency) to create a four-phase electrode array. To generate the four-phase electric field, the electrodes are connected to a 2-channel function generator and to two invertors. The phase shift between the adjacent electrodes is set at either 90° (for EROT) or 180° (for DEP). Representative results of AC electrokinetic measurements with a four-phase ITO electrode array are presented.

46 CFR 98.25-15 - Markings.

Code of Federal Regulations, 2010 CFR

2010-10-01

... safety relief valves, liquid level gaging devices and pressure gages shall be labeled to designate whether they terminate in the vapor or liquid space. Labels of noncorrosive material may be attached to...

46 CFR 98.25-15 - Markings.

Code of Federal Regulations, 2013 CFR

2013-10-01

... safety relief valves, liquid level gaging devices and pressure gages shall be labeled to designate whether they terminate in the vapor or liquid space. Labels of noncorrosive material may be attached to...

46 CFR 98.25-15 - Markings.

Code of Federal Regulations, 2014 CFR

2014-10-01

... safety relief valves, liquid level gaging devices and pressure gages shall be labeled to designate whether they terminate in the vapor or liquid space. Labels of noncorrosive material may be attached to...

46 CFR 98.25-15 - Markings.

Code of Federal Regulations, 2012 CFR

2012-10-01

... safety relief valves, liquid level gaging devices and pressure gages shall be labeled to designate whether they terminate in the vapor or liquid space. Labels of noncorrosive material may be attached to...

46 CFR 98.25-15 - Markings.

Code of Federal Regulations, 2011 CFR

2011-10-01

... safety relief valves, liquid level gaging devices and pressure gages shall be labeled to designate whether they terminate in the vapor or liquid space. Labels of noncorrosive material may be attached to...

Evaluation of retroreflectometers.

DOT National Transportation Integrated Search

2002-08-01

This project performed field-testing and analysis of two pavement marking retroreflectometers: the Laserlux and the : LTL2000. The Laserlux is a vehiclemounted device that takes readings at driving speed and produces : computerized output. The LTL...

SPORT-SPEAR Mark III Electronics (Engineering Materials)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The Drawing List DL 135-678-00-RO and the drawings listed thereon provide the specifications for construction of the SPORT-SPEAR Mark III Electronics. SPORT stands for Smark Port. This device is an adapter for the SLAC BADC (Brilliant Analog to Digital Converter) providing up to 5 ports whereas the BADC and SPORT takes signals from experimental equipment and directs them to other equipment and micro computers for processing and storing. These units are housed in standard Camac crates.

Improved mid infrared detector for high spectral or spatial resolution and synchrotron radiation use.

PubMed

Faye, Mbaye; Bordessoule, Michel; Kanouté, Brahim; Brubach, Jean-Blaise; Roy, Pascale; Manceron, Laurent

2016-06-01

When using bright, small effective size sources, such as synchrotron radiation light beam, for broadband spectroscopy at spectral or spatial high resolution for mid-IR FTIR measurements, a marked detectivity improvement can be achieved by setting up a device matching the detector optical étendue to that of the source. Further improvement can be achieved by reducing the background unmodulated flux and other intrinsic noise sources using a lower temperature cryogen, such as liquid helium. By the combined use of cooled apertures, cold reimaging optics, filters and adapted detector polarization, and preamplification electronics, the sensitivity of a HgCdTe photoconductive IR detector can be improved by a significant factor with respect to standard commercial devices (more than one order of magnitude on average over 6-20 μm region) and the usable spectral range extended to longer wavelengths. The performances of such an optimized detector developed on the AILES Beamline at SOLEIL are presented here.

A sub-1-volt analog metal oxide memristive-based synaptic device with large conductance change for energy-efficient spike-based computing systems

NASA Astrophysics Data System (ADS)

Hsieh, Cheng-Chih; Roy, Anupam; Chang, Yao-Feng; Shahrjerdi, Davood; Banerjee, Sanjay K.

2016-11-01

Nanoscale metal oxide memristors have potential in the development of brain-inspired computing systems that are scalable and efficient. In such systems, memristors represent the native electronic analogues of the biological synapses. In this work, we show cerium oxide based bilayer memristors that are forming-free, low-voltage (˜|0.8 V|), energy-efficient (full on/off switching at ˜8 pJ with 20 ns pulses, intermediate states switching at ˜fJ), and reliable. Furthermore, pulse measurements reveal the analog nature of the memristive device; that is, it can directly be programmed to intermediate resistance states. Leveraging this finding, we demonstrate spike-timing-dependent plasticity, a spike-based Hebbian learning rule. In those experiments, the memristor exhibits a marked change in the normalized synaptic strength (>30 times), when the pre- and post-synaptic neural spikes overlap. This demonstration is an important step towards the physical construction of high density and high connectivity neural networks.

Optofluidic microscope with 3D spatial resolution.

PubMed

Vig, Asger Laurburg; Marie, Rodolphe; Jensen, Eric; Kristensen, Anders

2010-03-01

This paper reports on-chip based optical detection with three-dimensional spatial resolution by integration of an optofluidic microscope (OFM) in a microfluidic pinched flow fractionation (PFF) separation device. This setup also enables on-chip particle image velocimetry (PIV). The position in the plane perpendicular to the flow direction and the velocity along the flow direction of separated fluorescent labeled polystyrene microspheres with diameters of 1 microm , 2.1 microm , 3 microm and 4 microm is determined by the OFM. These results are bench marked against those obtained with a PFF device using conventional fluorescence microscope readout. The size separated microspheres are detected by OFM with an accuracy of

PULSE AMPLITUDE DISTRIBUTION RECORDER

DOEpatents

Cowper, G.

1958-08-12

A device is described for automatica1ly recording pulse annplitude distribution received from a counter. The novelty of the device consists of the over-all arrangement of conventional circuit elements to provide an easy to read permanent record of the pulse amplitude distribution during a certain time period. In the device a pulse analyzer separates the pulses according to annplitude into several channels. A scaler in each channel counts the pulses and operates a pen marker positioned over a drivable recorder sheet. Since the scalers in each channel have the sanne capacity, the control circuitry permits counting of the incoming pulses until one scaler reaches capacity, whereupon the input is removed and an internal oscillator supplies the necessary pulses to fill up the other scalers. Movement of the chart sheet is initiated wben the first scaler reaches capacity to thereby give a series of marks at spacings proportional to the time required to fill the remaining scalers, and accessory equipment marks calibration points on the recorder sheet to facilitate direct reading of the number of external pulses supplied to each scaler.

46 CFR 38.05-5 - Markings-TB/ALL.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., except safety relief valves, liquid level gaging devices, and pressure gages, shall be labeled to designate whether they terminate in the vapor or liquid space. Labels of corrosion-resistant material may be...

46 CFR 38.05-5 - Markings-TB/ALL.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., except safety relief valves, liquid level gaging devices, and pressure gages, shall be labeled to designate whether they terminate in the vapor or liquid space. Labels of corrosion-resistant material may be...

46 CFR 38.05-5 - Markings-TB/ALL.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., except safety relief valves, liquid level gaging devices, and pressure gages, shall be labeled to designate whether they terminate in the vapor or liquid space. Labels of corrosion-resistant material may be...

46 CFR 38.05-5 - Markings-TB/ALL.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., except safety relief valves, liquid level gaging devices, and pressure gages, shall be labeled to designate whether they terminate in the vapor or liquid space. Labels of corrosion-resistant material may be...

46 CFR 38.05-5 - Markings-TB/ALL.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., except safety relief valves, liquid level gaging devices, and pressure gages, shall be labeled to designate whether they terminate in the vapor or liquid space. Labels of corrosion-resistant material may be...

46 CFR 160.048-6 - Marking.

Code of Federal Regulations, 2010 CFR

2010-10-01

... lettering: (1) In letters that can be read at a distance of 2 feet: Type IV Personal Flotation Device....); (Model No.). (Name and address of manufacturer or distributor.). (Lot No.). (Size; width, thickness, and...

9 CFR 312.8 - Official export inspection marks, devices, and certificates.

Code of Federal Regulations, 2011 CFR

2011-01-01

... SERVICE, DEPARTMENT OF AGRICULTURE AGENCY ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY... post-mortem inspection and were found sound and healthy and that it has been inspected and passed as...

9 CFR 312.8 - Official export inspection marks, devices, and certificates.

Code of Federal Regulations, 2010 CFR

2010-01-01

... SERVICE, DEPARTMENT OF AGRICULTURE AGENCY ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY... post-mortem inspection and were found sound and healthy and that it has been inspected and passed as...

Marked Object Recognition Multitouch Screen Printed Touchpad for Interactive Applications.

PubMed

Nunes, Jivago Serrado; Castro, Nelson; Gonçalves, Sergio; Pereira, Nélson; Correia, Vitor; Lanceros-Mendez, Senentxu

2017-12-01

The market for interactive platforms is rapidly growing, and touchscreens have been incorporated in an increasing number of devices. Thus, the area of smart objects and devices is strongly increasing by adding interactive touch and multimedia content, leading to new uses and capabilities. In this work, a flexible screen printed sensor matrix is fabricated based on silver ink in a polyethylene terephthalate (PET) substrate. Diamond shaped capacitive electrodes coupled with conventional capacitive reading electronics enables fabrication of a highly functional capacitive touchpad, and also allows for the identification of marked objects. For the latter, the capacitive signatures are identified by intersecting points and distances between them. Thus, this work demonstrates the applicability of a low cost method using royalty-free geometries and technologies for the development of flexible multitouch touchpads for the implementation of interactive and object recognition applications.

Marked Object Recognition Multitouch Screen Printed Touchpad for Interactive Applications

PubMed Central

Nunes, Jivago Serrado; Castro, Nelson; Pereira, Nélson; Correia, Vitor; Lanceros-Mendez, Senentxu

2017-01-01

The market for interactive platforms is rapidly growing, and touchscreens have been incorporated in an increasing number of devices. Thus, the area of smart objects and devices is strongly increasing by adding interactive touch and multimedia content, leading to new uses and capabilities. In this work, a flexible screen printed sensor matrix is fabricated based on silver ink in a polyethylene terephthalate (PET) substrate. Diamond shaped capacitive electrodes coupled with conventional capacitive reading electronics enables fabrication of a highly functional capacitive touchpad, and also allows for the identification of marked objects. For the latter, the capacitive signatures are identified by intersecting points and distances between them. Thus, this work demonstrates the applicability of a low cost method using royalty-free geometries and technologies for the development of flexible multitouch touchpads for the implementation of interactive and object recognition applications. PMID:29194414

Probe for production and measurement of acute mitral regurgitant flow in dog.

PubMed

Kléber, A G; Simon, R; Rutishauser, W

1976-02-01

A probe for production and measurement of acute mitral regurgitation in dogs is described. It consists of a tube that is introduced into the mitral valve through the left atrial appendage. Regurgitant flow through the tube is measured by an electromagnetic device. Variation of flow and zero flow are achieved by narrowing or occluding the tube with a rubber cuff. In animals weighing 30-50 kg, the probe does not produce significant mitral stenosis and the mitral leaflets fit closely around the probe during ventricular systole. The instantaneous relationship between mitral regurgitant flow (MRF) and the gradient between left ventricular and left atrial pressure shows a marked delay of MRF at the beginning and end of regurgitation. This delay can be attributed to some extent to electrical phase lag and to the small movement of the probe relative to the mitral valve during the cardiac cycle. Measurement of regurgitant stroke volume is affected by this movement only to a small extent.

Gate-Controlled Spin-Valley Locking of Resident Carriers in WSe2 Monolayers

NASA Astrophysics Data System (ADS)

Dey, P.; Yang, Luyi; Robert, C.; Wang, G.; Urbaszek, B.; Marie, X.; Crooker, S. A.

2017-09-01

Using time-resolved Kerr rotation, we measure the spin-valley dynamics of resident electrons and holes in single charge-tunable monolayers of the archetypal transition-metal dichalcogenide (TMD) semiconductor WSe2 . In the n -type regime, we observe long (˜130 ns ) polarization relaxation of electrons that is sensitive to in-plane magnetic fields By, indicating spin relaxation. In marked contrast, extraordinarily long (˜2 μ s ) polarization relaxation of holes is revealed in the p -type regime, which is unaffected by By, directly confirming long-standing expectations of strong spin-valley locking of holes in the valence band of monolayer TMDs. Supported by continuous-wave Kerr spectroscopy and Hanle measurements, these studies provide a unified picture of carrier polarization dynamics in monolayer TMDs, which can guide design principles for future valleytronic devices.

[The principle of registration, evaluation and testing of disinfecting preparations].

PubMed

Röhm-Rodowald, Ewa; Jakimiak, Bozenna; Podgórska, Marta

2008-01-01

Disinfectants are used to produce a state in which the number of living micro-organisms has been reduced to a level which is appropriate to the practical situation. For any products which are included in the Biocidal Directive 98/8/EC, for which specific activity is claimed, test data has to be approved by the regulatory authority and a product license obtained before the product can be offered for sale. Disinfectants can be recorded as biocidal products or medical devices. Presently, it is possible to measure the activity of a product on defined micro-organisms in specified experimental conditions. Efficacy is the result of the use of a product according to a defined application. To allow different requirements in different areas of application, separate tests and pass criteria have been or will be prepared for each of following three areas of application: medical, veterinary and group comprising food, industrial, domestic and institutional areas. The laboratory methods to be used for testing the activity of chemical disinfectants meets the European standards. The tests are categorised on a modular basis as follows: phase 1 tests, phase 2 step 1 tests, phase 2 step 2 tests and phase 3 tests. In order to claim that a product has disinfectant properties, suitable for use in the medical area, the product shall be tested according to European standards: phase 2 step 1 tests, phase 2 step 2 tests. Phase 1 tests are not required to support claims for chemical disinfectants used in human medicine. Only phase 1 tests are required to support claims for active substances for which no particular area of application is specified. Medical devices are subjects to the European Directive 93/42/EEC which requires that a product must carry a CE mark. Disinfectants which are intended specifically by its manufacturer to be used on medical devices are themselves medical devices and so these products, as well as conforming to the instrument disinfection European standards as specified in EN 14885, are also required to carry a CE mark.

Ultrafast lasers for precise and corrosion free marking on chirurgical steels

NASA Astrophysics Data System (ADS)

Neugebauer, Christoph; Aalderink, Dennis; Maurer, Erich; Faisst, Birgit; Budnicki, Aleksander

2017-02-01

The unique properties of ultrashort laser pulses and the decrease of invest pave the way to numerous novel applications. Even in the very price sensitive field of laser marking, ultrashort laser can compete due to a new cost structure and remarkable properties of the marking results. In this study we concentrated on industrial marking of medical equipment by using IR ultrashort lasers and compared the results with common marking laser systems. We demonstrate the benefits of ultrashort lasers marking on chirurgical devices, observing the influence of pulse energy, pulse duration, scanning velocity in respect to the visibility, corrosion resistance and long term durability under clinical conditions. Nowadays many parts and products are marked for the purpose of identification and traceability. One kind of laser marking is the well known annealing of stainless steel by nanosecond marking lasers. When annealing occurs a colored oxide layer grows due to the local heating of the material surface. Compared to the raw material, the annealed marking shows increased corrosion sensitivity. Regarding the traceability, the poor durability of the ns marking resulting in contrast reduction and the corrosion susceptibility are a huge problem. Therefore three different laser sources with ns-psfs pulse duration were observed. The focus rests on the realization of parameter studies (various lasers) and their effect on the corrosion and passivation behavior. Furthermore analysis of the oxide layers by use of EDX and XRD were performed to obtain further information on the composition and structure of the markings.

Patients' perception of pain during ultrasonic debridement: a comparison between piezoelectric and magnetostrictive scalers.

PubMed

Muhney, Kelly A; Dechow, Paul C

2010-01-01

To compare patients' perception of discomfort, vibration and noise levels between piezoelectric and the magnetostrictive ultrasonic units during periodontal debridement. Periodontal debridement was performed on 75 subjects using a split-mouth design. Two quadrants on the same side were instrumented with a piezoelectric ultrasonic device (EMS Swiss Mini Master® Piezon) and the remaining 2 quadrants were instrumented with a magnetostrictive ultrasonic device (Dentsply Cavitron® SPS™). Subjects marked between 0 and 100 along a visual analog scale (VAS) for each of the 3 variables immediately after treatment of each half of the dentition. Scores of the VAS were compared using a nonparametric test for paired data, the Wilcoxon Signed-Rank test. The level of significance was set at p<0.05. Descriptive statistics included the median and the first and third quartiles as a measure of variation. Mean scores for patient discomfort and vibration were greater for the magnetostrictive device at p=0.007 and p=0.032, respectively. The scores for noise level between the 2 ultrasonic types were almost equal. The results show that, on average, patients in this study prefer instrumentation with the piezoelectric as it relates to awareness of associated discomfort and vibration. The results of this study may assist the clinician in the decision over which ultrasonic device may prove more beneficial in decreasing patient discomfort and increasing patient compliance.

IAA RAS Radio Telescope Monitoring System

NASA Astrophysics Data System (ADS)

Mikhailov, A.; Lavrov, A.

2007-07-01

Institute of Applied Astronomy of the Russian Academy of Sciences (IAA RAS) has three identical radio telescopes, the receiving complex of which consists of five two-channel receivers of different bands, six cryogen systems, and additional devices: four local oscillators, phase calibration generators and IF commutator. The design, hardware and data communication protocol are described. The most convenient way to join the devices of the receiving complex into the common monitoring system is to use the interface which allows to connect numerous devices to the data bus. For the purpose of data communication regulation and to exclude conflicts, a data communication protocol has been designed, which operates with complex formatted data sequences. Formation of such sequences requires considerable data processing capability. That is provided by a microcontroller chip in each slave device. The test version of the software for the central computer has been developed in IAA RAS. We are developing the Mark IV FS software extension modules, which will allow us to control the receiving complex of the radio telescope by special SNAP commands from both operator input and schedule files. We are also developing procedures of automatic measurements of SEFD, system noise temperature and other parameters, available both in VLBI and single-dish modes of operation. The system described has been installed on all IAA RAS radio telescopes at "Svetloe", "Zelenchukskaya" and "Badary" observatories. It has proved to be working quite reliably and to show the perfonmance expected.

Spatial distribution of heavy metals in the surface soil of source-control stormwater infiltration devices - Inter-site comparison.

PubMed

Tedoldi, Damien; Chebbo, Ghassan; Pierlot, Daniel; Branchu, Philippe; Kovacs, Yves; Gromaire, Marie-Christine

2017-02-01

Stormwater runoff infiltration brings about some concerns regarding its potential impact on both soil and groundwater quality; besides, the fate of contaminants in source-control devices somewhat suffers from a lack of documentation. The present study was dedicated to assessing the spatial distribution of three heavy metals (copper, lead, zinc) in the surface soil of ten small-scale infiltration facilities, along with several physical parameters (soil moisture, volatile matter, variable thickness of the upper horizon). High-resolution samplings and in-situ measurements were undertaken, followed by X-ray fluorescence analyses and spatial interpolation. Highest metal accumulation was found in a relatively narrow area near the water inflow zone, from which concentrations markedly decreased with increasing distance. Maximum enrichment ratios amounted to >20 in the most contaminated sites. Heavy metal patterns give a time-integrated vision of the non-uniform infiltration fluxes, sedimentation processes and surface flow pathways within the devices. This element indicates that the lateral extent of contamination is mainly controlled by hydraulics. The evidenced spatial structure of soil concentrations restricts the area where remediation measures would be necessary in these systems, and suggests possible optimization of their hydraulic functioning towards an easier maintenance. Heterogeneous upper boundary conditions should be taken into account when studying the fate of micropollutants in infiltration facilities with either mathematical modeling or soil coring field surveys. Copyright © 2016 Elsevier B.V. All rights reserved.

Applications and requirements for MEMS scanner mirrors

NASA Astrophysics Data System (ADS)

Wolter, Alexander; Hsu, Shu-Ting; Schenk, Harald; Lakner, Hubert K.

2005-01-01

Micro scanning mirrors are quite versatile MEMS devices for the deflection of a laser beam or a shaped beam from another light source. The most exciting application is certainly in laser-scanned displays. Laser television, home cinema and data projectors will display the most brilliant colors exceeding even plasma, OLED and CRT. Devices for front and rear projection will have advantages in size, weight and price. These advantages will be even more important in near-eye virtual displays like head-mounted displays or viewfinders in digital cameras and potentially in UMTS handsets. Optical pattern generation by scanning a modulated beam over an area can be used also in a number of other applications: laser printers, direct writing of photo resist for printed circuit boards or laser marking and with higher laser power laser ablation or material processing. Scanning a continuous laser beam over a printed pattern and analyzing the scattered reflection is the principle of barcode reading in 1D and 2D. This principle works also for identification of signatures, coins, bank notes, vehicles and other objects. With a focused white-light or RGB beam even full color imaging with high resolution is possible from an amazingly small device. The form factor is also very interesting for the application in endoscopes. Further applications are light curtains for intrusion control and the generation of arbitrary line patterns for triangulation. Scanning a measurement beam extends point measurements to 1D or 2D scans. Automotive LIDAR (laser RADAR) or scanning confocal microscopy are just two examples. Last but not least there is the field of beam steering. E.g. for all-optical fiber switches or positioning of read-/write heads in optical storage devices. The variety of possible applications also brings a variety of specifications. This publication discusses various applications and their requirements.

Assessment of Tandem Measurements of pH and Total Gut Transit Time in Healthy Volunteers.

PubMed

Mikolajczyk, Adam E; Watson, Sydeaka; Surma, Bonnie L; Rubin, David T

2015-07-09

The variation of luminal pH and transit time in an individual is unknown, yet is necessary to interpret single measurements. This study aimed to assess the intrasubject variability of gut pH and transit time in healthy volunteers using SmartPill devices (Covidien, Minneapolis, MN). Each subject (n=10) ingested two SmartPill devices separated by 24 h. Mean pH values were calculated for 30 min after gastric emptying (AGE), before the ileocecal (BIC) valve, after the ileocecal (AIC) valve, and before body exit (BBE). Intrasubject variability was determined by comparing mean values from both ingestions for an individual subject using standard deviations, 95% limits of agreement, and Bland-Altman plots. Tandem device ingestion occurred without complication. The median (full range) intrasubject standard deviations for pH were 0.02 (0.0002-0.2048) for AGE, 0.06 (0.0002-0.3445) for BIC, 0.14 (0.0018-0.3042) for AIC, and 0.08 (0.0098-0.5202) for BBE. There was a significant change in pH for AIC (mean difference: -0.45±0.31, P=0.0015) observed across all subjects. The mean coefficients of variation for transit time were 12.0±7.4% and 25.8±15.8% for small and large bowels, respectively (P=0.01). This study demonstrates the safety and feasibility of tandem gut transit and pH assessments using the SmartPill device. In healthy individuals and over 24 h, the gut pH profile does not markedly fluctuate in a given region with more variation seen in the colon compared with the small bowel, which has important implications for future physiology and drug delivery studies.

ALIGNING JIG

DOEpatents

Culver, J.S.; Tunnell, W.C.

1958-08-01

A jig or device is described for setting or aligning an opening in one member relative to another member or structure, with a predetermined offset, or it may be used for measuring the amount of offset with which the parts have previously been sct. This jig comprises two blocks rabbeted to each other, with means for securing thc upper block to the lower block. The upper block has fingers for contacting one of the members to be a1igmed, the lower block is designed to ride in grooves within the reference member, and calibration marks are provided to determine the amount of offset. This jig is specially designed to align the collimating slits of a mass spectrometer.

Strategies for effective roundabout approach speed reduction : final report.

DOT National Transportation Integrated Search

2017-05-01

Appropriate deceleration on approaches to roundabouts is primarily accomplished through the use of applicable geometric design principles; however, traffic control devices (specifically signing and markings on the approach) also serve a vital role in...

15 CFR 1150.2 - Prohibitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... ADMINISTRATION, DEPARTMENT OF COMMERCE MARKING OF TOY, LOOK-ALIKE AND IMITATION FIREARMS § 1150.2 Prohibitions... imitation firearm (“device”) covered by this part as set forth in § 1150.1 of this part unless such device...

[Implementation and evaluation of error prevention measures in surgical clinics: Results of a current online survey].

PubMed

Rothmund, Matthias; Kohlmann, Thomas; Heidecke, Claus-Dieter; Siebert, Hartmut; Ansorg, Jörg

2015-01-01

In the autumn of 2014, more than 3,000 surgeons completed an online questionnaire asking for the prevalence and efficiency of instruments to prevent adverse events within surgical departments in Germany. About 90 % of the respondents stated that perioperative checklists, preoperative marking of the surgical site and the documentation of hospital infections had been implemented in their institution; and 75 % of the institutions had introduced critical incident reporting systems (CIRS), morbidity and mortality conferences and identification bracelets for patients. The surgeons were asked to rank the different instruments for the prevention of adverse events. According to the respondents, preoperative marking of the surgical site and the use of checklists were at the top of the efficacy ranking, followed by an introductory course for surgeons starting work in a hospital or when new devices became available. Only 50 % of the responding surgeons perceived CIRS as being efficient. Overall, the answers showed that instruments to increase patient safety were commonly available in surgical departments. On the other hand, there is still room for improvement in daily practice. Copyright © 2015. Published by Elsevier GmbH.

Leveling

USGS Publications Warehouse

1966-01-01

Geodetic leveling by the U.S. Geological Survey provides a framework of accurate elevations for topographic mapping. Elevations are referred to the Sea Level Datum of 1929. Lines of leveling may be run either with automatic or with precise spirit levels, by either the center-wire or the three-wire method. For future use, the surveys are monumented with bench marks, using standard metal tablets or other marking devices. The elevations are adjusted by least squares or other suitable method and are published in lists of control.

Coma measurement by use of an alternating phase-shifting mask mark with a specific phase width

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qiu Zicheng; Wang Xiangzhao; Yuan Qiongyan

2009-01-10

The correlation between the coma sensitivity of the alternating phase-shifting mask (Alt-PSM) mark and the mark's structure is studied based on the Hopkins theory of partially coherent imaging and positive resist optical lithography (PROLITH) simulation. It is found that an optimized Alt-PSM mark with its phase width being two-thirds its pitch has a higher sensitivity to coma than Alt-PSM marks with the same pitch and the different phase widths. The pitch of the Alt-PSM mark is also optimized by PROLITH simulation, and the structure of p=1.92{lambda}/NA and pw=2p/3 proves to be with the highest sensitivity. The optimized Alt-PSM mark ismore » used as a measurement mark to retrieve coma aberration from the projection optics in lithographic tools. In comparison with an ordinary Alt-PSM mark with its phase width being a half its pitch, the measurement accuracies of Z7 and Z14 apparently increase.« less

46 CFR 69.67 - Marking of cargo spaces.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Marking of cargo spaces. 69.67 Section 69.67 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DOCUMENTATION AND MEASUREMENT OF VESSELS MEASUREMENT OF VESSELS Convention Measurement System § 69.67 Marking of cargo spaces. Cargo spaces used in...

46 CFR 69.67 - Marking of cargo spaces.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Marking of cargo spaces. 69.67 Section 69.67 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DOCUMENTATION AND MEASUREMENT OF VESSELS MEASUREMENT OF VESSELS Convention Measurement System § 69.67 Marking of cargo spaces. Cargo spaces used in...

46 CFR 69.67 - Marking of cargo spaces.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Marking of cargo spaces. 69.67 Section 69.67 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DOCUMENTATION AND MEASUREMENT OF VESSELS MEASUREMENT OF VESSELS Convention Measurement System § 69.67 Marking of cargo spaces. Cargo spaces used in...

46 CFR 69.67 - Marking of cargo spaces.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Marking of cargo spaces. 69.67 Section 69.67 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DOCUMENTATION AND MEASUREMENT OF VESSELS MEASUREMENT OF VESSELS Convention Measurement System § 69.67 Marking of cargo spaces. Cargo spaces used in...

46 CFR 69.67 - Marking of cargo spaces.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Marking of cargo spaces. 69.67 Section 69.67 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DOCUMENTATION AND MEASUREMENT OF VESSELS MEASUREMENT OF VESSELS Convention Measurement System § 69.67 Marking of cargo spaces. Cargo spaces used in...

A method of camera calibration in the measurement process with reference mark for approaching observation space target

NASA Astrophysics Data System (ADS)

Zhang, Hua; Zeng, Luan

2017-11-01

Binocular stereoscopic vision can be used for space-based space targets near observation. In order to solve the problem that the traditional binocular vision system cannot work normally after interference, an online calibration method of binocular stereo measuring camera with self-reference is proposed. The method uses an auxiliary optical imaging device to insert the image of the standard reference object into the edge of the main optical path and image with the target on the same focal plane, which is equivalent to a standard reference in the binocular imaging optical system; When the position of the system and the imaging device parameters are disturbed, the image of the standard reference will change accordingly in the imaging plane, and the position of the standard reference object does not change. The camera's external parameters can be re-calibrated by the visual relationship of the standard reference object. The experimental results show that the maximum mean square error of the same object can be reduced from the original 72.88mm to 1.65mm when the right camera is deflected by 0.4 degrees and the left camera is high and low with 0.2° rotation. This method can realize the online calibration of binocular stereoscopic vision measurement system, which can effectively improve the anti - jamming ability of the system.

Comparison of multiple non-invasive methods of measuring cardiac output during pregnancy reveals marked heterogeneity in the magnitude of cardiac output change between women.

PubMed

Petersen, John W; Liu, Jing; Chi, Yueh-Yun; Lingis, Melissa; Williams, R Stan; Rhoton-Vlasak, Alice; Segal, Mark S; Conrad, Kirk P

2017-04-01

Various non-invasive methods are available to measure cardiac output (CO) during pregnancy. We compared serial measures of CO using various methods to determine which provided the least variability. Ten patients with spontaneous pregnancy had estimation of CO at baseline prior to becoming pregnant and at the end of the first and third trimesters. Echocardiographic data were used to estimate CO using the Teichholz method, Simpson's biplane method, and the Doppler determined velocity time integral (VTI) method. In addition, a Bioz Dx device was used to estimate CO by impedance cardiography. CO estimated with the VTI method had the lowest beat-to-beat variability. CO estimated with the VTI method was higher than CO estimated with the 2D-Teichholz method and Simpson's method. The percent change in CO during pregnancy was similar for all echo methods (VTI, Teichholz, and Simpson's biplane). Baseline CO determined with impedance cardiography was higher than CO determined with the VTI method. However, change in CO during pregnancy was significantly lower when measured with impedance cardiography. There was marked heterogeneity in the degree of rise in CO during the first trimester (-3 to 55%). The wide variation in the gestational rise in CO was unexpected, and at least in part secondary to variable increase in heart rate. We recommend the use of the Doppler determined VTI method for the estimation of CO in pregnancy. © 2017 The Authors. Physiological Reports published by Wiley Periodicals, Inc. on behalf of The Physiological Society and the American Physiological Society.

7 CFR 54.2 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2010 CFR

2010-01-01

... AGRICULTURAL MARKETING ACT OF 1946 AND THE EGG PRODUCTS INSPECTION ACT (CONTINUED) MEATS, PREPARED MEATS, AND MEAT PRODUCTS (GRADING, CERTIFICATION, AND STANDARDS) Regulations Definitions § 54.2 Designation of...

7 CFR 54.2 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2011 CFR

2011-01-01

... AGRICULTURAL MARKETING ACT OF 1946 AND THE EGG PRODUCTS INSPECTION ACT (CONTINUED) MEATS, PREPARED MEATS, AND MEAT PRODUCTS (GRADING, CERTIFICATION, AND STANDARDS) Regulations Definitions § 54.2 Designation of...

OroSTIFF: Face-referenced measurement of perioral stiffness in health and disease.

PubMed

Chu, Shin-Ying; Barlow, Steven M; Kieweg, Douglas; Lee, Jaehoon

2010-05-28

A new device and automated measurement technology known as OroSTIFF is described to characterize non-participatory perioral stiffness in healthy adults for eventual application to patients with orofacial movement disorders associated with neuromotor disease, traumatic injury, or congenital clefts of the upper lip. Previous studies of perioral biomechanics required head stabilization for extended periods of time during measurement, which precluded sampling patients with involuntary body/head movements (dyskinesias), or pediatric subjects. The OroSTIFF device is face-referenced and avoids the complications associated with head-restraint. Supporting data of non-participatory perioral tissue stiffness using OroSTIFF are included from 10 male and 10 female healthy subjects. The OroSTIFF device incorporates a pneumatic glass air cylinder actuator instrumented for pressure, and an integrated subminiature displacement sensor to encode lip aperture. Perioral electromyograms were simultaneously sampled to confirm passive muscle state for the superior and inferior divisions of the orbicularis oris muscles. Perioral stiffness, derived as a quotient from resultant force (DeltaF) and interangle span (DeltaX), was modeled with multilevel regression techniques. Real-time calculation of the perioral stiffness function demonstrated a significant quadratic relation between imposed interangle stretch and resultant force. This stiffness growth function also differed significantly between males and females. This study demonstrates the OroSTIFF 'proof-of-concept' for cost-effective non-invasive stimulus generation and derivation of perioral stiffness in a group of healthy unrestrained adults, and a case study to illustrate the dose-dependent effects of Levodopa on perioral stiffness in an individual with advanced Parkinson's disease who exhibited marked dyskinesia and rigidity. Copyright 2010 Elsevier Ltd. All rights reserved.

Characterization of Carbon Dioxide Washout Measurement Techniques in the Mark-III Space Suit

NASA Technical Reports Server (NTRS)

Meginnis, Ian M.; Norcross, Jason; Bekdash, Omar; Ploutz-Snyder, Robert

2016-01-01

A space suit must provide adequate carbon dioxide (CO2) washout inside the helmet to prevent symptoms of hypercapnia. In the past, an oronasal mask has been used to measure the inspired air of suited subjects to determine a space suit's CO2 washout capability. While sufficient for super-ambient pressure testing of space suits, the oronasal mask fails to meet several human factors and operational criterion needed for future sub-ambient pressure testing (e.g. compatibility with a Valsalva device). This paper describes the evaluation of a nasal cannula as a device for measuring inspired air within a space suit. Eight test subjects were tasked with walking on a treadmill or operating an arm ergometer to achieve target metabolic rates of 1000, 2000, and 3000 British thermal units per hour (BTU/hr), at flow rates of 2, 4, and 6 actual cubic feet per minute (ACFM). Each test configuration was conducted twice, with subjects instructed to breathe either through their nose only, or however they felt comfortable. Test data shows that the nasal cannula provides more statistically consistent data across test subjects than the oronasal mask used in previous tests. The data also shows that inhaling/exhaling through only the nose provides a lower sample variance than a normal breathing style. Nose-only breathing reports better CO2 washout due to several possible reasons, including a decreased respiratory rate, an increased tidal volume, and because nose-only breathing directs all of the exhaled CO2 down and away from the oronasal region. The test subjects in this study provided feedback that the nasal cannula is comfortable and can be used with the Valsalva device.

Evaluation of Two New Electronic Apex-Locator-Controlled Handpieces Using a NiTi Rotary File: An In Vitro Study.

PubMed

Nazarimoghadam, Kiumarz; Labaf, Hossein

2013-11-01

The aim of this in-vitro study was to compare the accuracy of two new electronic apex-locator controlled handpieces (EALHs) using the first rotary Mtwo file while rotating in the canal. A total of 36 extracted mandibular molar teeth were selected. The lengths of the mesio-buccal canals to the major foramina were measured directly using a size 10 K-file introduced in the canal until the tip was visible under a loupe and then 0.5 mm was subtracted from the recorded lengths as the actual working lengths (AWLs). Subsequently, the teeth were randomly assigned to two groups and embedded in an alginate model. Auto-stop function of the EALHs was preset at "0.5" mark and then electrical working lengths (EWLs) in groups 1 and 2 were recorded by VDW GOLD and Dentaport ZX, respectively. Analysis of variance (ANOVA, 1-way) and Tukey pairwise multiple comparison intervals (0.05) were used to compare the accuracy of the two electronic devices. For VDW GOLD, 61.1% of the measurements were within ±0.5 mm and 88.9% were within ±1 mm of the AWL. For Dentaport ZX, 88.9% of the measurements were within ±0.5 mm and 94.4% were within ±1mm of the AWL. There was no significant difference between AWLs and EWLs (p=0.466 for Dentaport ZX and p=0.283 for VDW Gold) and between the accuracy of the two devices in determining the EWL (p=0.8). Both Dentaport ZX and VDW Gold were suitable for determining working length using a rotary file. To avoid over instrumenting the canal, we recommend setting the devices to automatically stop or reverse the rotary file at 1 mm level.

A nonimaging scintillation probe to measure penile hemodynamics.

PubMed

Zuckier, L S; Korupolu, G R; Gladshteyn, M; Sattenberg, R; Goldstein, R; Ricciardi, R; Goodwin, P; Melman, A; Blaufox, M D

1995-12-01

We have developed a penile nonimaging scintillation (PNIS) probe consisting of a plastic well-type scintillation crystal interfaced to a portable computer and acquisition board. This report describes the design of the PNIS probe, performance characteristics, mode of usage and illustrative results which demonstrate its capabilities. With the PNIS probe, penile blood-pool studies were performed in nine patients utilizing 3.7 MBq (100 microCi) autologous 99mTc-labeled red blood cells (RBCs). Venous blood standards were assayed to enable conversion of the count rate to volummetric measurements. Washin of peripherally administered 99mTc-RBCs was mathematically analyzed to estimate penile blood volume and cavernosal flow rate in the flaccid state. The rate of change of penile blood volume after intracavernosal vasodilators was used to generate measures of stimulated flow. A major advantage of this device over the gamma-camera is a 3300-fold increase in count rate sensitivity, which allows for markedly improved temporal resolution while significantly reducing the radiopharmaceutical dosage. Additionally, the PNIS probe is portable, economical and is not dependent on operator-defined regions of interest. Count rate sensitivity is relatively constant within the bore, with the exception of the proximal region adjacent to the opening, where geometric efficiency is reduced. The PNIS probe is an effective device for measuring penile activity in radionuclide studies, allowing for acquisition of time-activity curves of the penis during flaccid washin of peripherally labeled red blood cells and after pharmacologic stimulation to induce erection.

[Determination of the detergent efficiency of the detergents disinfecting for surfaces].

PubMed

Santucci, R; Kuntzmann, X; Mesli, N; Meunier, O

2009-01-01

Since the disinfecting activity of disinfectants is evaluated by standards, the intrinsic detergent activity is not easily quantifiable and no standard have been suggested yet. Beyond the physicochemical parameters like wettability or foaming presented by the manufacturers, it appears necessary to us to objectively measure the real effect of the detergent agent. The objective of our work is to propose a simple, fast and reproducible method to evaluate detersive activity of the disinfecting detergents. We measured three factors (total amount of extracted bacteria, extraction efficiency and slope of extracting curve) by using Rodac prints technique on two different supports (PVC, stainless steel) that have been contaminated by either E. coli or S. aureus. An increasing mark from 1 to 6 is given to each of these factors in case of statistically differences. The three factors allowed us to calculate a "Specific Index of detersion" (SI) for each germ/support couple (3 to 18). Addition of the marks given to each couple for each disinfecting detergent allowed to calculate a "Globally Index of detersion" (GI) (9 to 72). We tested 4 commercialised disinfecting detergents: Surfanios, Aniosurf, Major C100 and Ecodiol. All detergents may be classified according to their effectiveness on a bacterium/support couple (value of the SI). This enlights a specific spectrum for each disinfecting detergents. As a result, Ecodiol seems to be the most effective deterging agent on 3 of the 4 germ/support couples (S. aureus/PVC, E. coli/PVC and E. coli/stainless steel), whereas Aniosurf is most effective on the S. aureus/stainless steel couple. The GI is very useful to choose the best compromise between activities for all situations. GI rankings of the tested agents were as follows: water < Aniosurf < Surfanios < neutralizing < Major C100 < Ecodiol. This experimental model will be used to test and compare the intrinsic detergent activities of other commercialised products which are usually used for the biocleaning of the medical devices (i.e. endoscopes or reusable dialysis device).

Aircraft vortex marking program

NASA Technical Reports Server (NTRS)

Pompa, M. F.

1979-01-01

A simple, reliable device for identifying atmospheric vortices, principally as generated by in-flight aircraft and with emphasis on the use of nonpolluting aerosols for marking by injection into such vortex (-ices) is presented. The refractive index and droplet size were determined from an analysis of aerosol optical and transport properties as the most significant parameters in effecting vortex optimum light scattering (for visual sighting) and visual persistency of at least 300 sec. The analysis also showed that a steam-ejected tetraethylene glycol aerosol with droplet size near 1 micron and refractive index of approximately 1.45 could be a promising candidate for vortex marking. A marking aerosol was successfully generated with the steam-tetraethylene glycol mixture from breadboard system hardware. A compact 25 lb/f thrust (nominal) H2O2 rocket chamber was the key component of the system which produced the required steam by catalytic decomposition of the supplied H2O2.

Towards a Better Corrosion Resistance and Biocompatibility Improvement of Nitinol Medical Devices

NASA Astrophysics Data System (ADS)

Rokicki, Ryszard; Hryniewicz, Tadeusz; Pulletikurthi, Chandan; Rokosz, Krzysztof; Munroe, Norman

2015-04-01

Haemocompatibility of Nitinol implantable devices and their corrosion resistance as well as resistance to fracture are very important features of advanced medical implants. The authors of the paper present some novel methods capable to improve Nitinol implantable devices to some marked degree beyond currently used electropolishing (EP) processes. Instead, a magnetoelectropolishing process should be advised. The polarization study shows that magnetoelectropolished Nitinol surface is more corrosion resistant than that obtained after a standard EP and has a unique ability to repassivate the surface. Currently used sterilization processes of Nitinol implantable devices can dramatically change physicochemical properties of medical device and by this influence its biocompatibility. The Authors' experimental results clearly show the way to improve biocompatibility of NiTi alloy surface. The final sodium hypochlorite treatment should replace currently used Nitinol implantable devices sterilization methods which rationale was also given in our previous study.

9 CFR 327.26 - Official import inspection marks and devices.

Code of Federal Regulations, 2010 CFR

2010-01-01

... horsemeat food products. EC11SE91.027 For application to mule and other (nonhorse) equine carcasses, primal parts, and cuts, not in containers. EC11SE91.028 For application to outside containers of equine meat...

46 CFR 199.175 - Survival craft and rescue boat equipment.

Code of Federal Regulations, 2012 CFR

2012-10-01

... equivalent device, either permanently installed or attached to the boat by a lanyard or chain, must be provided for each oar. Each oar should have the vessel's name marked on it in block letters. (21) Painter...

46 CFR 199.175 - Survival craft and rescue boat equipment.

Code of Federal Regulations, 2013 CFR

2013-10-01

... equivalent device, either permanently installed or attached to the boat by a lanyard or chain, must be provided for each oar. Each oar should have the vessel's name marked on it in block letters. (21) Painter...

46 CFR 199.175 - Survival craft and rescue boat equipment.

Code of Federal Regulations, 2014 CFR

2014-10-01

... equivalent device, either permanently installed or attached to the boat by a lanyard or chain, must be provided for each oar. Each oar should have the vessel's name marked on it in block letters. (21) Painter...

Results of the International Space Station Interim Resistance Exercise Device Man-in-the-Loop Test

NASA Technical Reports Server (NTRS)

Moore, A. D., Jr.; Amonette, W. E.; Bentley, J. R.; Rapley, M. G.; Blazine, K. L.; Loehr, J. A.; Collier, K. R.; Boettcher, C. R.; Skrocki, J. S.; Hohrnann, R. J.

2004-01-01

The Interim Resistance Exercise Device (iRED), developed for the International Space Station (ISS), was evaluated using human subjects for a Man-In-The-Loop Test (MILT). Thirty-two human subjects exercised using the iRED in a test that was conducted over a 63-working-day period. The subjects performed the same exercises will be used on board ISS, and the iRED operating constraints that are to be used on ISS were followed. In addition, eight of the subjects were astronauts who volunteered to be in the evaluation in order to become familiar with the iRED and provide a critique of the device. The MILT was scheduled to last for 57,000 exercise repetitions on the iRED. This number of repetitions was agreed to as a number typical of that expected during a 3-person, 17-week ISS Increment. One of the canisters of the iRED failed at the 49,683- repetition mark (87.1% of targeted goal). The remaining canister was operated using the plan for operations if one canister fails during flight (contingency operations). This canister remained functional past the 57,000-repetition mark. This report details the results of the iRED MILT, and lists specific recommendations regarding both operation of the iRED and future resistance exercise device development.

Instantaneous centers of rotation in dorsi/plantar flexion movements of posterior-type plastic ankle-foot orthoses.

PubMed

Sumiya, T; Suzuki, Y; Kasahara, T; Ogata, H

1997-07-01

Hingeless plastic ankle-foot orthoses (PAFOs) achieve ankle motion by flexing about the ankle joint. Instantaneous centers of rotation (ICRs) in dorsi- and plantarflexion movements, used as a measure of PAFO axes of movement, were measured to evaluate their fit to ankle motion. Thirty different PAFOs were fabricated and their stiffness modified in three stages. They were dorsi- and plantarflexed 16 degrees at 2 degrees-intervals using an original device. Displacement of two marks on the lateral calf-cuff were traced photographically, and ICRs were determined by plotting intersections of vertical bisectors for each displacement. The ICRs converged on the junction between the calf shell and the shoe insert. They deviated posteriorly from the anatomical ankle axis and caused the calf-cuff to move up-down during dorsi- and plantarflexion movements. However, this poor fit of the PAFO to ankle motion can be sufficiently compensated for by fastening straps more loosely.

Lightweight helmet-mounted eye movement measurement system

NASA Technical Reports Server (NTRS)

Barnes, J. A.

1978-01-01

The helmet-mounted eye movement measuring system, weighs 1,530 grams; the weight of the present aviators' helmet in standard form with the visor is 1,545 grams. The optical head is standard NAC Eye-Mark. This optical head was mounted on a magnesium yoke which in turn was attached to a slide cam mounted on the flight helmet. The slide cam allows one to adjust the eye-to-optics system distance quite easily and to secure it so that the system will remain in calibration. The design of the yoke and slide cam is such that the subject can, in an emergency, move the optical head forward and upward to the stowed and locked position atop the helmet. This feature was necessary for flight safety. The television camera that is used in the system is a solid state General Electric TN-2000 with a charged induced device imager used as the vidicon.

Phantom-based evaluation method for surgical assistance devices in minimally invasive cochlear implantation

NASA Astrophysics Data System (ADS)

Lexow, G. Jakob; Kluge, Marcel; Majdani, Omid; Lenarz, Thomas; Rau, Thomas S.

2017-03-01

Several research groups have proposed individual solutions for surgical assistance devices to perform minimally invasive cochlear implantation. The main challenge is the drilling of a small bore hole from the surface of the skull to the inner ear at submillimetric accuracy. Each group tested the accuracy of their device in their respective test bench or in a small number of temporal bone specimens. This complicates the comparison of the different approaches. Thus, a simple and inexpensive phantom based evaluation method is proposed which resembles clinical conditions. The method is based on half-skull phantoms made of bone-substitute material - optionally equipped with an artificial skin replica to include skin incision within the evaluation procedure. Anatomical structures of the temporal bone derived from segmentations using clinical imaging data are registered into a computer tomographic scan of the skull phantom and used for the planning of the drill trajectory. Drilling is performed with the respective device under conditions close to the intraoperative setting. Evaluation of accuracy can either be performed through postoperative imaging or by means of added targets on the inside of the skull model. Two different targets are proposed: simple reference marks only for measuring the accuracy of the device and a target containing a scala tympani model for evaluation of the complete workflow including the insertion of the electrode carrier. Experiments using the presented method take place under reproducible conditions thus allowing the comparison of the different approaches. In addition, artificial phantoms are easier to obtain and handle than human specimens.

Skeletal and soft tissue changes and stability in cleft lip and palate patients after distraction osteogenesis using a new intraoral maxillary device.

PubMed

Ansari, Edward; Tomat, Catherine; Kadlub, Natacha; Diner, Patrick A; Bellocq, Thomas; Vazquez, Marie-Paule; Picard, Arnaud

2015-04-01

The authors have recently reported on the use of an internal maxillary distraction device. In this study, we report on the hard and soft tissue movements achieved with this intraoral distraction device, and the stability changes after distraction osteogenesis for maxillary hypoplasia in patients with cleft lip and palate. Ten male patients with severe hypoplasia of the maxilla, with complete uni- or bilateral cleft lip and palate were included. The mean age of the patients at the time of operation was 11.91 years (±3.41). To evaluate the distraction process and stability, superimpositions on the preoperative lateral cephalograms were performed. The mean follow-up (FU) was 15.42 months (±3.94). Cephalometric measurements at all of the maxillary hard and soft tissue points improved significantly. Maxillary point A was advanced by 8.25 mm (±3.17; P < 0.001). After distraction soft tissue point A' had advanced 7.10 mm (±2.69; P < 0.001). The soft tissue to hard tissue ratio at point A was 0.86:1 after distraction. Maxillary horizontal relapse at point A was 14.1% at FU. Vertical relapse was not significant. This rigid intraoral distraction device can be successfully used in the correction of severe maxillary hypoplasia. The marked aesthetic improvement and low psychological encumbrance make this device viable for the treatment of cleft-related hypoplasia of the maxilla. Copyright © 2014 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Measurements of the Exerted Pressure by Pelvic Circumferential Compression Devices

PubMed Central

Knops, Simon P; van Riel, Marcel P.J.M; Goossens, Richard H.M; van Lieshout, Esther M.M; Patka, Peter; Schipper, Inger B

2010-01-01

Background: Data on the efficacy and safety of non-invasive Pelvic Circumferential Compression Devices (PCCDs) is limited. Tissue damage may occur if a continuous pressure on the skin exceeding 9.3 kPa is sustained for more than two or three hours. The aim of this study was to gain insight into the pressure build-up at the interface, by measuring the PCCD-induced pressure when applying pulling forces to three different PCCDs (Pelvic Binder® , SAM-Sling ® and T-POD® ) in a simplified model. Methods: The resulting exerted pressures were measured at four ‘anatomical’ locations (right, left, posterior and anterior) in a model using a pressure measurement system consisting of pressure cuffs. Results: The exerted pressure varied substantially between the locations as well as between the PCCDs. Maximum pressures ranged from 18.9-23.3 kPa and from 19.2-27.5 kPa at the right location and left location, respectively. Pressures at the posterior location stayed below 18 kPa. At the anterior location pressures varied markedly between the different PCCDs. Conclusion: The circumferential compression by the different PCCDs showed high pressures measured at the four locations using a simplified model. Difference in design and functional characteristics of the PCCDs resulted in different pressure build-up at the four locations. When following the manufacturer’s instructions, the exerted pressure of all three PCCDs tested exceeded the tissue damaging level (9.3 kPa). In case of prolonged use in a clinical situation this might put patients at risk for developing tissue damage. PMID:20361001

Hybrid Piezoelectric/Fiber-Optic Sensor Sheets

NASA Technical Reports Server (NTRS)

Lin, Mark; Qing, Xinlin

2004-01-01

Hybrid piezoelectric/fiber-optic (HyPFO) sensor sheets are undergoing development. They are intended for use in nondestructive evaluation and long-term monitoring of the integrity of diverse structures, including aerospace, aeronautical, automotive, and large stationary ones. It is anticipated that the further development and subsequent commercialization of the HyPFO sensor systems will lead to economic benefits in the form of increased safety, reduction of life-cycle costs through real-time structural monitoring, increased structural reliability, reduction of maintenance costs, and increased readiness for service. The concept of a HyPFO sensor sheet is a generalization of the concept of a SMART Layer(TradeMark), which is a patented device that comprises a thin dielectric film containing an embedded network of distributed piezoelectric actuator/sensors. Such a device can be mounted on the surface of a metallic structure or embedded inside a composite-material structure during fabrication of the structure. There is has been substantial interest in incorporating sensors other than piezoelectric ones into SMART Layer(TradeMark) networks: in particular, because of the popularity of the use of fiber-optic sensors for monitoring the "health" of structures in recent years, it was decided to incorporate fiber-optic sensors, giving rise to the concept of HyPFO devices.

Decreased endometrial HOXA10 expression associated with use of the copper intrauterine-device

PubMed Central

Tetrault, Amy M; Richman, Susan M; Fei, Xiaolan; Taylor, Hugh S

2009-01-01

Objective To characterize human endometrial HOXA10 expression in patients using copper intrauterine devices (IUD). Design Case-control study. Setting Academic medical center Patient(s) Women using copper IUD Interventions(s) Immunohistochemical analysis of endometrial HOXA10 expression in biopsies obtained from 24 women using copper Paraguard T380A as well as in biopsies obtained from 10 normal cycling women who were not using IUD or hormonal contraceptives. Main Outcome Measure(s) Endometrial HOXA10 expression. Result(s) Endometrial HOXA10 expression was markedly decreased in biopsies obtained from women using IUD contraceptive when compared to controls. The mean H score for endometrial stromal cell HOXA10 expression in biopsies obtained from women using Paraguard IUD was 0.21 compared to 2.2 in the control endometrial biopsies (P<0.001). Endometrial glandular expression of HOXA10 was absent in all IUD users. Conclusion(s) Decreased endometrial HOXA10 expression was apparent in women who use a copper IUD. Expression of HOXA10 is essential for endometrial receptivity. A novel mechanism of copper IUD action involves suppression of genes required for endometrial receptivity. The dramatic decrease of endometrial HOXA10 in response to IUD use may contribute to contraceptive efficacy. PMID:18930214

Advances in Plexcore active layer technology systems for organic photovoltaics: roof-top and accelerated lifetime analysis of high performance organic photovoltaic cells

NASA Astrophysics Data System (ADS)

Laird, Darin W.; Vaidya, Swanand; Li, Sergey; Mathai, Mathew; Woodworth, Brian; Sheina, Elena; Williams, Shawn; Hammond, Troy

2007-09-01

We report NREL-certified efficiencies and initial lifetime data for organic photovoltaic (OPV) cells based on Plexcore PV photoactive layer and Plexcore HTL-OPV hole transport layer technology. Plexcore PV-F3, a photoactive layer OPV ink, was certified in a single-layer OPV cell at the National Renewable Energy Laboratory (NREL) at 5.4%, which represents the highest official mark for a single-layer organic solar cell. We have fabricated and measured P3HT:PCBM solar cells with a peak efficiency of 4.4% and typical efficiencies of 3 - 4% (internal, NREL-calibrated measurement) with P3HT manufactured at Plextronics by the Grignard Metathesis (GRIM) method. Outdoor and accelerated lifetime testing of these devices is reported. Both Plexcore PV-F3 and P3HT:PCBM-based OPV cells exhibit >750 hours of outdoor roof-top, non-accelerated lifetime with less than 8% loss in initial efficiency for both active layer systems when exposed continuously to the climate of Western Pennsylvania. These devices are continuously being tested to date. Accelerated testing using a high-intensity (1000W) metal-halide lamp affords shorter lifetimes; however, the true acceleration factor is still to be determined.

Calibration-free assays on standard real-time PCR devices

PubMed Central

Debski, Pawel R.; Gewartowski, Kamil; Bajer, Seweryn; Garstecki, Piotr

2017-01-01

Quantitative Polymerase Chain Reaction (qPCR) is one of central techniques in molecular biology and important tool in medical diagnostics. While being a golden standard qPCR techniques depend on reference measurements and are susceptible to large errors caused by even small changes of reaction efficiency or conditions that are typically not marked by decreased precision. Digital PCR (dPCR) technologies should alleviate the need for calibration by providing absolute quantitation using binary (yes/no) signals from partitions provided that the basic assumption of amplification a single target molecule into a positive signal is met. Still, the access to digital techniques is limited because they require new instruments. We show an analog-digital method that can be executed on standard (real-time) qPCR devices. It benefits from real-time readout, providing calibration-free assessment. The method combines advantages of qPCR and dPCR and bypasses their drawbacks. The protocols provide for small simplified partitioning that can be fitted within standard well plate format. We demonstrate that with the use of synergistic assay design standard qPCR devices are capable of absolute quantitation when normal qPCR protocols fail to provide accurate estimates. We list practical recipes how to design assays for required parameters, and how to analyze signals to estimate concentration. PMID:28327545

Calibration-free assays on standard real-time PCR devices

NASA Astrophysics Data System (ADS)

Debski, Pawel R.; Gewartowski, Kamil; Bajer, Seweryn; Garstecki, Piotr

2017-03-01

Quantitative Polymerase Chain Reaction (qPCR) is one of central techniques in molecular biology and important tool in medical diagnostics. While being a golden standard qPCR techniques depend on reference measurements and are susceptible to large errors caused by even small changes of reaction efficiency or conditions that are typically not marked by decreased precision. Digital PCR (dPCR) technologies should alleviate the need for calibration by providing absolute quantitation using binary (yes/no) signals from partitions provided that the basic assumption of amplification a single target molecule into a positive signal is met. Still, the access to digital techniques is limited because they require new instruments. We show an analog-digital method that can be executed on standard (real-time) qPCR devices. It benefits from real-time readout, providing calibration-free assessment. The method combines advantages of qPCR and dPCR and bypasses their drawbacks. The protocols provide for small simplified partitioning that can be fitted within standard well plate format. We demonstrate that with the use of synergistic assay design standard qPCR devices are capable of absolute quantitation when normal qPCR protocols fail to provide accurate estimates. We list practical recipes how to design assays for required parameters, and how to analyze signals to estimate concentration.

78 FR 34156 - Hazardous Materials: Emergency Recall Order

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-06

... unilateral changes to its manufacturing process, quality control oversight, and cylinder designs without... never functioned as designed, and indicated that the shutdown device had not stopped the manufacturing... 33-pound cylinders. Jurisdiction Lite Cylinder manufactures or has manufactured, marked, certified...

23 CFR 656.5 - Eligibility.

Code of Federal Regulations, 2010 CFR

2010-04-01

... carpool lanes. Eligible work may include preliminary engineering to determine traffic flow and design criteria, signing, pavement markings, traffic control devices, and minor physical modifications to permit... any existing or planned mass transportation service, but should be designed so that the facility could...

23 CFR 656.5 - Eligibility.

Code of Federal Regulations, 2014 CFR

2014-04-01

... carpool lanes. Eligible work may include preliminary engineering to determine traffic flow and design criteria, signing, pavement markings, traffic control devices, and minor physical modifications to permit... any existing or planned mass transportation service, but should be designed so that the facility could...

23 CFR 656.5 - Eligibility.

Code of Federal Regulations, 2012 CFR

2012-04-01

... carpool lanes. Eligible work may include preliminary engineering to determine traffic flow and design criteria, signing, pavement markings, traffic control devices, and minor physical modifications to permit... any existing or planned mass transportation service, but should be designed so that the facility could...

23 CFR 656.5 - Eligibility.

Code of Federal Regulations, 2011 CFR

2011-04-01

... carpool lanes. Eligible work may include preliminary engineering to determine traffic flow and design criteria, signing, pavement markings, traffic control devices, and minor physical modifications to permit... any existing or planned mass transportation service, but should be designed so that the facility could...

23 CFR 656.5 - Eligibility.

Code of Federal Regulations, 2013 CFR

2013-04-01

... carpool lanes. Eligible work may include preliminary engineering to determine traffic flow and design criteria, signing, pavement markings, traffic control devices, and minor physical modifications to permit... any existing or planned mass transportation service, but should be designed so that the facility could...

76 FR 41398 - Prohibition on the Employment, or Attempted Employment, of Manipulative and Deceptive Devices and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-14

... CONTACT: David Meister, Director, Division of Enforcement, 202-418-5624, or Mark D. Higgins, Counsel... and NPRA at page 11. \\65\\ API and NPRA at page 23. Mr. Chris Barnard (``Barnard'') believes the...

Middleware Architecture for Ambient Intelligence in the Networked Home

NASA Astrophysics Data System (ADS)

Georgantas, Nikolaos; Issarny, Valerie; Mokhtar, Sonia Ben; Bromberg, Yerom-David; Bianco, Sebastien; Thomson, Graham; Raverdy, Pierre-Guillaume; Urbieta, Aitor; Cardoso, Roberto Speicys

With computing and communication capabilities now embedded in most physical objects of the surrounding environment and most users carrying wireless computing devices, the Ambient Intelligence (AmI) / pervasive computing vision [28] pioneered by Mark Weiser [32] is becoming a reality. Devices carried by nomadic users can seamlessly network with a variety of devices, both stationary and mobile, both nearby and remote, providing a wide range of functional capabilities, from base sensing and actuating to rich applications (e.g., smart spaces). This then allows the dynamic deployment of pervasive applications, which dynamically compose functional capabilities accessible in the pervasive network at the given time and place of an application request.

Pulse X-ray device for stereo imaging and few-projection tomography of explosive and fast processes

NASA Astrophysics Data System (ADS)

Palchikov, E. I.; Dolgikh, A. V.; Klypin, V. V.; Krasnikov, I. Y.; Ryabchun, A. M.

2017-10-01

This paper describes the operation principles and design features of the device for single pulse X-raying of explosive and high-speed processes, developed on the basis of a Tesla transformer with lumped secondary capacitor bank. The circuit with the lumped capacitor bank allows transferring a greater amount of energy to the discharge circuit as compared with the Marks-surge generator for more effective operation with remote X-ray tubes connected by coaxial cables. The device equipped with multiple X-ray tubes provides simultaneous X-raying of extended or spaced objects, stereo imaging, or few-projection tomography.

Slow Auger Relaxation in HgTe Colloidal Quantum Dots.

PubMed

Melnychuk, Christopher; Guyot-Sionnest, Philippe

2018-05-03

The biexciton lifetimes in HgTe colloidal quantum dots are measured as a function of particle size. Samples produced by two synthetic methods, leading to partially aggregated or well-dispersed particles, exhibit markedly different dynamics. The relaxation characteristics of partially aggregated HgTe inhibit reliable determinations of the Auger lifetime. In well-dispersed HgTe quantum dots, the biexciton lifetime increases approximately linearly with particle volume, confirming trends observed in other systems. The extracted Auger coefficient is three orders of magnitude smaller than that for bulk HgCdTe materials with similar energy gaps. We discuss these findings in the context of understanding Auger relaxation in quantum-confined systems and their relevance to mid-infrared optoelectronic devices based on HgTe colloidal quantum dots.

Effect of Y2O3 on polyindole for high frequency capacitor application

NASA Astrophysics Data System (ADS)

Maji, P.; Choudhary, R. B.; Majhi, M.

2017-05-01

Polyindole-Yittrium Oxide (PIn-Y2O3) composite was synthesized in the laboratory through chemical polymerization process. The structural and morphological studies of PIn-Y2O3 composite were investigated using X-ray diffraction (XRD) and scanning electron microscopic (SEM) techniques. These studies showed that PIn-Y2O3 composite was amorphous in nature and formed with spherical granule shape. The dielectric response was measured through LCR meter in the frequency range from 100 Hz to 1 MHz. The dielectric studies revealed that incorporation of Y2O3 into polymeric matrix improved the dielectric behavior of PIn polymer and markedly suitable for its application in high frequency capacitor and many other electronic devices.

An automated system for performing continuous viscosity versus temperature measurements of fluids using an Ostwald viscometer

NASA Astrophysics Data System (ADS)

Beaulieu, L. Y.; Logan, E. R.; Gering, K. L.; Dahn, J. R.

2017-09-01

An automated system was developed to measure the viscosity of fluids as a function of temperature using image analysis tracking software. An Ostwald viscometer was placed in a three-wall dewar in which ethylene glycol was circulated using a thermal bath. The system collected continuous measurements during both heating and cooling cycles exhibiting no hysteresis. The use of video tracking analysis software greatly reduced the measurement errors associated with measuring the time required for the meniscus to pass through the markings on the viscometer. The stability of the system was assessed by performing 38 consecutive measurements of water at 42.50 ± 0.05 °C giving an average flow time of 87.7 ± 0.3 s. A device was also implemented to repeatedly deliver a constant volume of liquid of 11.00 ± 0.03 ml leading to an average error in the viscosity of 0.04%. As an application, the system was used to measure the viscosity of two Li-ion battery electrolyte solvents from approximately 10 to 40 °C with results showing excellent agreement with viscosity values calculated using Gering's Advanced Electrolyte Model (AEM).

Lunar environment and design of China's first moon rover Yutu

NASA Astrophysics Data System (ADS)

Jianhui, Wu

China launched the Chang'e-3 lunar probe with the country's first moon rover aboard on Dec.14, marking a significant step toward deep space exploration.Lunar environment and environmental tests of typical lunar survyeors are discussed in this papaer.According to the needs of China's lunar exploration project,environmental impact of moon rovers and Yutu design ideas are studied.Through the research, temperature control device, micro-gravity environment design ,dust and other equipment devices used on Yutu all meet the mission requirements.

Evaluating Mobile Device Ownership and Usage in the U.S. Army: Implications for Army Training

DTIC Science & Technology

2014-07-01

any of the following mobile devices? MARK ALL THAT APPLY? iPhone iPad (or other tablet PC) iPhone Touch Android smartphone Blackberry E-Reader (e.g...THAT APPLY? iPhone iPad (or other tablet PC) iPhone Touch Android smartphone Blackberry E-Reader (e.g., Kindle, Nook) None of the above 5...age groups owned more iPhones than Android or Blackberrys . These trends changed as age increased. Upper- middle-aged Soldiers owned a mix of

Effects of an Air-Powder Abrasive Device When Used during Periodontal Flap Surgery in Dogs.

DTIC Science & Technology

1983-01-01

instru- ments, ultrasonic devices, air driven reciprocating hand- pieces, and air driven rotary handpieces (Schaffer, 1967). None of these techniques...system, the Prophy-Jet Mark IV C-100 , may be an alternative to conventional mechanical and chemical methods of detoxifying roots. The handpiece is...electric current and uses inlet air pressure of 65 to 100 p.s.i. and inlet water pressure of 25 to 60 p.s.i. The handpiece propels particles of the

Programmable shunt valve interactions with osseointegrated hearing devices.

PubMed

Pierson, Matthew J; Wehrmann, Daniel; Albers, J Andrew; El Tecle, Najib E; Costa, Dary; Elbabaa, Samer K

2017-04-01

OBJECTIVE Patients with ventriculoperitoneal (VP) shunts with programmable valves who would benefit from osseointegrated hearing devices (OIHDs) represent a unique population. The aim of this study was to evaluate the magnetic field strengths of 4 OIHDs and their interactions with 5 programmable VP shunt valves. METHODS Magnetic field strength was measured as a function of distance for each hearing device (Cochlear Baha 5, Cochlear Baha BP110, Oticon Ponto Plus Power, and Medtronic Sophono) in the following modes: inactive, active in quiet, and active in 60 decibels of background noise in the sound booth. The hearing devices were introduced to each shunt valve (Aesculap proGAV, Aesculap proGAV 2.0, Codman Hakim, Codman Certas, and Medtronic Strata II) also as a function of distance in these identical 3 settings. Each trial was repeated 5 times. Between each trial, the valves were assessed for a change in setting. Finally, using a skull model, the devices were introduced to each other in standard anatomical locations and the valves were assessed for a change in settings. RESULTS The maximum magnetic field strengths generated by the Cochlear Baha 5, BP110, and Oticon OIHDs were 1.1, 36.2, and 48.7 gauss (G), respectively. The maximum strength generated by the Sophono device was > 800 G. The magnetic field strength of the hearing devices decreased markedly with increasing distance from the device. The strength of the Sophono's magnetic attachment decreased to 34.8 G at 5 mm. The Codman Hakim, Codman Certas, and Medtronic Strata II valve settings changed when rotating the valves next to the Sophono abutment. No other changes in valve settings occurred in the distance or anatomical models for any other trials. CONCLUSIONS This is the first study evaluating the interaction between OIHDs and programmable VP shunt valves. The findings suggest that it is safe to use these devices together without having to switch to a nonprogrammable valve or move the shunt valve to a more distant location. Still, care should be taken if the Sophono device is used to ensure that the valve is ≥ 5 mm away from the magnetic attachment.

Radiation-Hard Complementary Integrated Circuits Based on Semiconducting Single-Walled Carbon Nanotubes.

PubMed

McMorrow, Julian J; Cress, Cory D; Gaviria Rojas, William A; Geier, Michael L; Marks, Tobin J; Hersam, Mark C

2017-03-28

Increasingly complex demonstrations of integrated circuit elements based on semiconducting single-walled carbon nanotubes (SWCNTs) mark the maturation of this technology for use in next-generation electronics. In particular, organic materials have recently been leveraged as dopant and encapsulation layers to enable stable SWCNT-based rail-to-rail, low-power complementary metal-oxide-semiconductor (CMOS) logic circuits. To explore the limits of this technology in extreme environments, here we study total ionizing dose (TID) effects in enhancement-mode SWCNT-CMOS inverters that employ organic doping and encapsulation layers. Details of the evolution of the device transport properties are revealed by in situ and in operando measurements, identifying n-type transistors as the more TID-sensitive component of the CMOS system with over an order of magnitude larger degradation of the static power dissipation. To further improve device stability, radiation-hardening approaches are explored, resulting in the observation that SWNCT-CMOS circuits are TID-hard under dynamic bias operation. Overall, this work reveals conditions under which SWCNTs can be employed for radiation-hard integrated circuits, thus presenting significant potential for next-generation satellite and space applications.

A porous ceramic membrane tailored high-temperature supercapacitor

NASA Astrophysics Data System (ADS)

Zhang, Xin; He, Benlin; Zhao, Yuanyuan; Tang, Qunwei

2018-03-01

The supercapacitor that can operate at high-temperature are promising for markedly increase in capacitance because of accelerated charge movement. However, the state-of-the-art polymer-based membranes will decompose at high temperature. Inspired by solid oxide fuel cells, we present here the experimental realization of high-temperature supercapacitors (HTSCs) tailored with porous ceramic separator fabricated by yttria-stabilized zirconia (YSZ) and nickel oxide (NiO). Using activated carbon electrode and supporting electrolyte from potassium hydroxide (KOH) aqueous solution, a category of symmetrical HTSCs are built in comparison with a conventional polymer membrane based device. The dependence of capacitance performance on temperature is carefully studied, yielding a maximized specific capacitance of 272 F g-1 at 90 °C for the optimized HTSC tailored by NiO/YSZ membrane. Moreover, the resultant HTSC has relatively high durability when suffer repeated measurement over 1000 cycles at 90 °C, while the polymer membrane based supercapacitor shows significant reduction in capacitance at 60 °C. The high capacitance along with durability demonstrates NiO/YSZ membrane tailored HTSCs are promising in future advanced energy storage devices.

Advances in process overlay on 300-mm wafers

NASA Astrophysics Data System (ADS)

Staecker, Jens; Arendt, Stefanie; Schumacher, Karl; Mos, Evert C.; van Haren, Richard J. F.; van der Schaar, Maurits; Edart, Remi; Demmerle, Wolfgang; Tolsma, Hoite

2002-07-01

Overlay budgets are getting tighter within 300 mm volume production and as a consequence the process effects on alignment and off-line metrology becomes more important. In a short loop experiment, with cleared reference marks in each image field, the isolated effect of processing was measured with a sub-nanometer accuracy. The examined processes are Shallow Trench Isolation (STI), Tungsten-Chemical Mechanical Processing (W-CMP) and resist spinning. The alignment measurements were done on an ASML TWINSCANT scanner and the off-line metrology measurements on a KLA Tencor. Mark type and mark position dependency of the process effects are analyzed. The mean plus 3 (sigma) of the maximum overlay after correcting batch average wafer parameters is used as an overlay performance indicator (OPI). 3 (sigma) residuals to the wafer-model are used as an indicator of the noise that is added by the process. The results are in agreement with existing knowledge of process effects on 200 mm wafers. The W-CMP process introduces an additional wafer rotation and scaling that is similar for alignment marks and metrology targets. The effects depend on the mark type; in general they get less severe for higher spatial frequencies. For a 7th order alignment mark, the OPI measured about 12 nm and the added noise about 12 nm. For the examined metrology targets the OPI is about 20 nm with an added noise of about 90 nm. Two different types of alignment marks were tested in the STI process, i.e., zero layer marks and marks that were exposed together with the STI product. The overlay contribution due to processing on both types of alignment marks is very low (smaller than 5 nm OPI) and independent on mark type. Some flyers are observed fot the zero layer marks. The flyers can be explained by the residues of oxide and nitride that is left behind in the spaces of the alignment marks. Resist spinning is examined on single layer resist and resist with an organic Bottom Anti-Reflective Coating (BARC) underneath. Single layer resist showed scaling on unsegmented marks that disappears using higher diffraction orders and/or mark segmentation. Resist with a planarizing BARC caused additional effects on the wafer edge for measurements with the red laser signal. The effects disappear using the green laser of ATHENAT.

Design of automatic leveling and centering system of theodolite

NASA Astrophysics Data System (ADS)

Liu, Chun-tong; He, Zhen-Xin; Huang, Xian-xiang; Zhan, Ying

2012-09-01

To realize the theodolite automation and improve the azimuth Angle measurement instrument, the theodolite automatic leveling and centering system with the function of leveling error compensation is designed, which includes the system solution, key components selection, the mechanical structure of leveling and centering, and system software solution. The redesigned leveling feet are driven by the DC servo motor; and the electronic control center device is installed. Using high precision of tilt sensors as horizontal skew detection sensors ensures the effectiveness of the leveling error compensation. Aiming round mark center is located using digital image processing through surface array CCD; and leveling measurement precision can reach the pixel level, which makes the theodolite accurate centering possible. Finally, experiments are conducted using the automatic leveling and centering system of the theodolite. The results show the leveling and centering system can realize automatic operation with high centering accuracy of 0.04mm.The measurement precision of the orientation angle after leveling error compensation is improved, compared with that of in the traditional method. Automatic leveling and centering system of theodolite can satisfy the requirements of the measuring precision and its automation.

7 CFR 51.50 - Custody of official inspection marking devices.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Section 51.50 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946 FRESH FRUITS, VEGETABLES AND OTHER PRODUCTS 1,2 (INSPECTION, CERTIFICATION...

7 CFR 51.50 - Custody of official inspection marking devices.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Section 51.50 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946 FRESH FRUITS, VEGETABLES AND OTHER PRODUCTS 1,2 (INSPECTION, CERTIFICATION...

49 CFR 221.5 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Definitions. 221.5 Section 221.5 Transportation... TRANSPORTATION REAR END MARKING DEVICE-PASSENGER, COMMUTER AND FREIGHT TRAINS General § 221.5 Definitions. As... defined by the Illuminating Engineering Society's Guide for Calculating the Effective Intensity of...

Development of an Intelligent Stretching Device for Ankle Joints With Contracture/Spasticity

DTIC Science & Technology

2001-10-25

percentage corresponded to background dorsi-flexion muscle contraction and 0% was the relaxed state. Next, tendon reflexes were evaluated...the representative cases, joint stiffness was reduced markedly after stretching across the range of muscle contraction (Fig. 5), including both

Results of the post-market Registry to Evaluate the HeartWare Left Ventricular Assist System (ReVOLVE).

PubMed

Strueber, Martin; Larbalestier, Robert; Jansz, Paul; Zimpfer, Daniel; Fiane, Arnt E; Tsui, Steven; Simon, André; Schmitto, Jan D; Khaghani, Asghar; Wieselthaler, George M; Najarian, Kevin; Schueler, Stephan

2014-05-01

The post-market Registry to Evaluate the HeartWare Left Ventricular Assist System (ReVOLVE) is an investigator-initiated registry established to collect post-CE Mark Trial clinical data on patients receiving a HeartWare ventricular assist device (HVAD) in the European Union and Australia. The ReVOLVE is a multi-center, prospective, single-arm registry performed at seven centers in Europe and two in Australia. Herein we describe a total of 254 commercial HVAD implants according to labeled indications between February 2009 and November 2012. Summary statistics included patients' demographics, adverse events, length of support and outcomes. Compared with the clinical trial supporting the CE Mark of the HeartWare system, patient selection differed in that patients were older, and there were higher proportions of females and patients with idiopathic cardiomyopathies in the ReVOLVE cohort. Duration of support ranged from 1 to 1,057 days, with a mean of 363 ± 280 days (median 299.5 days). Transplantation was done in 56 patients (22%), explant for recovery was performed in 3 patients (1%), 43 died while on support (17%), and 152 (60%) remain on the device. Success in patients with the HeartWare system was 87% at 6 months, 85% at 1 year, 79% at 2 years and 73% at 3 years. Adverse event rates were low, comparable or improved when compared to the CE Mark Trial. Real-world use of the HeartWare system continues to demonstrate excellent clinical outcomes in patients supported with the device. Copyright © 2014 International Society for Heart and Lung Transplantation. Published by Elsevier Inc. All rights reserved.

Magnetic Particle / Magnetic Resonance Imaging: In-Vitro MPI-Guided Real Time Catheter Tracking and 4D Angioplasty Using a Road Map and Blood Pool Tracer Approach.

PubMed

Salamon, Johannes; Hofmann, Martin; Jung, Caroline; Kaul, Michael Gerhard; Werner, Franziska; Them, Kolja; Reimer, Rudolph; Nielsen, Peter; Vom Scheidt, Annika; Adam, Gerhard; Knopp, Tobias; Ittrich, Harald

2016-01-01

In-vitro evaluation of the feasibility of 4D real time tracking of endovascular devices and stenosis treatment with a magnetic particle imaging (MPI) / magnetic resonance imaging (MRI) road map approach and an MPI-guided approach using a blood pool tracer. A guide wire and angioplasty-catheter were labeled with a thin layer of magnetic lacquer. For real time MPI a custom made software framework was developed. A stenotic vessel phantom filled with saline or superparamagnetic iron oxide nanoparticles (MM4) was equipped with bimodal fiducial markers for co-registration in preclinical 7T MRI and MPI. In-vitro angioplasty was performed inflating the balloon with saline or MM4. MPI data were acquired using a field of view of 37.3×37.3×18.6 mm3 and a frame rate of 46 volumes/sec. Analysis of the magnetic lacquer-marks on the devices were performed with electron microscopy, atomic absorption spectrometry and micro-computed tomography. Magnetic marks allowed for MPI/MRI guidance of interventional devices. Bimodal fiducial markers enable MPI/MRI image fusion for MRI based roadmapping. MRI roadmapping and the blood pool tracer approach facilitate MPI real time monitoring of in-vitro angioplasty. Successful angioplasty was verified with MPI and MRI. Magnetic marks consist of micrometer sized ferromagnetic plates mainly composed of iron and iron oxide. 4D real time MP imaging, tracking and guiding of endovascular instruments and in-vitro angioplasty is feasible. In addition to an approach that requires a blood pool tracer, MRI based roadmapping might emerge as a promising tool for radiation free 4D MPI-guided interventions.

Improvement in conformability of the latest generation of thoracic stent grafts.

PubMed

Canaud, Ludovic; Cathala, Philipe; Joyeux, Frédéric; Branchereau, Pascal; Marty-Ané, Charles; Alric, Pierre

2013-04-01

Poor aortic arch apposition increases the risk of technical failure after thoracic endovascular repair. The aim of this study was to assess the conformability of the latest generation of thoracic stent grafts in relation to the degree of device oversizing and aortic arch angulation. A benchtop pulsatile flow model was designed to test stent graft anchorage in a 2-cm-long proximal landing zone at varying landing zone angles (from 140° down to 70°) and stent graft oversizing (12%-28%). The experiments were performed using 10 human thoracic cadaveric aortas and four stent grafts: C-TAG, Zenith TX2 Pro-Form, Valiant Captivia, and Relay. Device-wall apposition was measured as a function of landing zone angulation and oversizing during static and dynamic (60 pulses/min, 300/150 mm Hg) tests. The Valiant stent graft remained apposed to the aortic wall at each increment of neck angulation and device oversizing. Lack of apposition of the proximal anchorage segment was observed with the C-TAG above 120° landing zone angulation (1-2 mm) and with the Relay above 110° landing zone angulation (1-4 mm). Lack of "body" apposition (1-4 mm) was first observed with the Zenith Pro-Form stent graft above 110° angulation (P = .001). When the device was not apposed to the aortic wall, an increase in stent graft oversizing significantly (P = .01) decreased device-wall apposition. The requirement for close conformability has influenced the design of next-generation devices. Manufacturers have modified devices and/or their deployment system to specifically address this problem. When compared with the results of our previous experimental test, this study demonstrates that these alterations have resulted in a marked improvement in the performance of commercially available stent graft systems. Copyright © 2013 Society for Vascular Surgery. Published by Mosby, Inc. All rights reserved.

Omeprazole and dry mouth.

PubMed

Teare, J P; Spedding, C; Whitehead, M W; Greenfield, S M; Challacombe, S J; Thompson, R P

1995-03-01

Omeprazole causes irreversible inhibition of the hydrogen/potassium adenosine triphosphatase enzyme, leading to a marked reduction in both acid secretion and volume of gastric juice. Reported side-effects include nausea, vomiting, diarrhoea, constipation, and headache. We report the development of dry mouth during omeprazole therapy. We have identified six patients taking omeprazole for more than 6 weeks who complained of a dry mouth. Salivary production was measured as whole salivary flow produced over a 10-min period spat into a collecting vessel and as 5% citric acid-stimulated parotid salivary flow collected with a Lashley cup device placed over the parotid duct. Flow rates were evaluated both during and after cessation of treatment. Saliva produced was then cultured for microbes. Four of the six had subnormal parotid or whole salivary flow rates on treatment that recovered after stopping treatment. The increase after treatment was marked in four. Significant amounts of Candida albicans grew from the saliva of the three patients with the lowest salivary flows; one saliva also grew Staphylococcus aureus. Salivary flow is reduced in some patients treated with omeprazole, returning to normal after cessation of treatment. This reduction may predispose to opportunistic infection, particularly in the edentulous.

Actin dynamics at the living cell submembrane imaged by total internal reflection fluorescence photobleaching.

PubMed Central

Sund, S E; Axelrod, D

2000-01-01

Although reversible chemistry is crucial to dynamical processes in living cells, relatively little is known about relevant chemical kinetic rates in vivo. Total internal reflection/fluorescence recovery after photobleaching (TIR/FRAP), an established technique previously demonstrated to measure reversible biomolecular kinetic rates at surfaces in vitro, is extended here to measure reversible biomolecular kinetic rates of actin at the cytofacial (subplasma membrane) surface of living cells. For the first time, spatial imaging (with a charge-coupled device camera) is used in conjunction with TIR/FRAP. TIR/FRAP imaging produces both spatial maps of kinetic parameters (off-rates and mobile fractions) and estimates of kinetic correlation distances, cell-wide kinetic gradients, and dependences of kinetic parameters on initial fluorescence intensity. For microinjected rhodamine actin in living cultured smooth muscle (BC3H1) cells, the unbinding rate at or near the cytofacial surface of the plasma membrane (averaged over the entire cell) is measured at 0.032 +/- 0.007 s(-1). The corresponding rate for actin marked by microinjected rhodamine phalloidin is very similar, 0.033 +/- 0.013 s(-1), suggesting that TIR/FRAP is reporting the dynamics of entire filaments or protofilaments. For submembrane fluorescence-marked actin, the intensity, off-rate, and mobile fraction show a positive correlation over a characteristic distance of 1-3 microm and a negative correlation over larger distances greater than approximately 7-14 microm. Furthermore, the kinetic parameters display a statistically significant cell-wide gradient, with the cell having a "fast" and "slow" end with respect to actin kinetics. PMID:10969025

Leukocyte Subtype Counts and Its Association with Vascular Structure and Function in Adults with Intermediate Cardiovascular Risk. MARK Study

PubMed Central

Gomez-Sanchez, Leticia; García-Ortiz, Luis; Recio-Rodríguez, José I.; Patino-Alonso, Maria C.; Agudo-Conde, Cristina; Rigo, Fernando; Ramos, Rafel; Martí, Ruth; Gomez-Marcos, Manuel A.

2015-01-01

Objectives We investigated the relationship between leukocyte subtype counts and vascular structure and function based on carotid intima-media thickness, pulse wave velocity, central augmentation index and cardio-ankle vascular index by gender in intermediate cardiovascular risk patients. Methods This study analyzed 500 subjects who were included in the MARK study, aged 35 to 74 years (mean: 60.3±8.4), 45.6% women. Measurement: Brachial ankle Pulse Wave Velocity (ba-PWV) estimate by equation, Cardio-AnkleVascular Index (CAVI) using the VaSera device and Carotid ultrasound was used to measure carotid Intima Media Thickness (IMT). The Mobil-O-Graph was used to measure the Central Augmentation Index (CAIx). Results Total leukocyte, neutrophil and monocyte counts were positively correlated with IMT (p < 0.01) in men. Monocyte count was positively correlated with CAIx in women (p < 0.01). In a multiple linear regression analysis, the IMT mean maintained a positive association with the neutrophil count (β = 1.500, p = 0.007) in men. CAIx maintained a positive association with the monocyte count (β = 2.445, p = 0.022) in women. Conclusion The results of this study suggest that the relationship between subtype circulating leukocyte counts and vascular structure and function, although small, may be different by gender. In men, the neutrophil count was positively correlated with IMT and in women, the monocyte count with CAIx, in a large sample of intermediate-risk patients. These association were maintained after adjusting for age and other confounders. Trial Registration ClinicalTrials.gov NCT01428934 PMID:25885665

Acoustic properties of vocal singing in prelingually-deafened children with cochlear implants or hearing aids.

PubMed

Mao, Yitao; Zhang, Mengchao; Nutter, Heather; Zhang, Yijing; Zhou, Qixin; Liu, Qiaoyun; Wu, Weijing; Xie, Dinghua; Xu, Li

2013-11-01

The purpose of the present study was to investigate vocal singing performance of hearing-impaired children with cochlear implants (CI) and hearing aids (HA) as well as to evaluate the relationship between demographic factors of those hearing-impaired children and their singing ability. Thirty-seven prelingually-deafened children with CIs and 31 prelingually-deafened children with HAs, and 37 normal-hearing (NH) children participated in the study. The fundamental frequencies (F0) of each note in the recorded songs were extracted and the duration of each sung note was measured. Five metrics were used to evaluate the pitch-related and rhythm-based aspects of singing accuracy. Children with CIs and HAs showed significantly poorer performance in either the pitch-based assessments or the rhythm-based measure than the NH children. No significant differences were seen between the CI and HA groups in all of these measures except for the mean deviation of the pitch intervals. For both hearing-impaired groups, length of device use was significantly correlated with singing accuracy. There is a marked deficit in vocal singing ability either in pitch or rhythm accuracy in a majority of prelingually-deafened children who have received CIs or fitted with HAs. Although an increased length of device use might facilitate singing performance to some extent, the chance for the hearing-impaired children fitted with either HAs or CIs to reach high proficiency in singing is quite slim. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Effect of planecta and ROSE™ on the frequency characteristics of blood pressure-transducer kits.

PubMed

Fujiwara, Shigeki; Kawakubo, Yoshifumi; Mori, Satoshi; Tachihara, Keiichi; Toyoguchi, Izumi; Yokoyama, Takeshi

2015-12-01

Pressure-transducer kits have frequency characteristics such as natural frequency and damping coefficient, which affect the monitoring accuracy. The aim of the present study was to investigate the effect of planecta ports and a damping device (ROSE™, Argon Medical Devices, TX, USA) on the frequency characteristics of pressure-transducer kits. The FloTrac sensor kit (Edwards Lifesciences, CA, USA) and the DTXplus transducer kit (Argon Medical Devices) were prepared with planecta ports, and their frequency characteristics were tested with or without ROSE™. The natural frequency and damping coefficient of each kit were obtained using frequency characteristics analysis software and evaluated by plotting them on the Gardner's chart. By inserting a planecta port, the natural frequency markedly decreased in both the FloTrac sensor kit (from 40 to 22 Hz) and the DTXplus transducer kit (from 35 to 22 Hz). In both kits with one planecta port, the damping coefficient markedly increased by insertion of ROSE™ from 0.2 to 0.5, optimising frequency characteristics. In both kits with two planecta ports, however, the natural frequency decreased from 22 to 12 Hz. The damping coefficient increased from 0.2 to 0.8 by insertion of ROSE™; however, optimisation was not achieved even by ROSE™ insertion. Planecta ports decrease the natural frequency of the kit. ROSE™ is useful to optimise the frequency characteristics in the kits without or with one planecta port. However, optimisation is difficult with two or more planecta ports, even with the ROSE™ device.

9 CFR 312.2 - Official marks and devices to identify inspected and passed products of cattle, sheep, swine, or...

Code of Federal Regulations, 2010 CFR

2010-01-01

... livers, beef tongues, beef hearts, and smoked meats not in casings. EC11SE91.003 For application to... on shipping containers, band labels, artificial casings, and other articles with the approval of the...

Pedestrian/bicyclist warning devices and signs at highway-rail and pathway-rail grade crossings.

DOT National Transportation Integrated Search

2013-04-01

Federal reporting shows a relatively constant number of pedestrian and bicycle fatalities at highway-rail and : pathway-rail grade crossings over the past 10 years. This is in contrast to a marked decrease in trainvehicle : collisions at highway-r...

Population size, breeding biology and on-land threats of Cape Verde petrel (Pterodroma feae) in Fogo Island, Cape Verde

PubMed Central

Zango, Laura; Calabuig, Pascual; Stefan, Laura M.; González-Solís, Jacob

2017-01-01

Cape Verde petrel (Pterodroma feae) is currently considered near threatened, but little is known about its population size, breeding biology and on land threats, jeopardizing its management and conservation. To improve this situation, we captured, marked and recaptured (CMR) birds using mist-nets over 10 years; measured and sexed them; monitored up to 14 burrows, deployed GPS devices on breeders and analyzed activity data of geolocators retrieved from breeders in Fogo (Cape Verde). We set cat traps over the colony and investigated their domestic/feral origin by marking domestic cats from a nearby village with transponders, by deploying GPS devices on domestic cats and by performing stable isotope analyses of fur of the trapped and domestic cats. The population of Fogo was estimated to be 293 birds, including immatures (95% CI: 233–254, CMR modelling). Based on geolocator activity data and nest monitoring we determined the breeding phenology of this species and we found biometric differences between sexes. While monitoring breeding performance, we verified a still ongoing cat predation and human harvesting. Overall, data gathered from trapped cats without transponder, cats GPS trips and the distinct isotopic values between domestic and trapped cats suggest cats visiting the colony are of feral origin. GPS tracks from breeders showed birds left and returned to the colony using the sector NE of the islands, where high level of public lights should be avoided specially during the fledging period. Main threats for the Cape Verde petrel in the remaining breeding islands are currently unknown but likely to be similar to Fogo, calling for an urgent assessment of population trends and the control of main threats in all Cape Verde Islands and uplisting its conservation status. PMID:28369105

Population size, breeding biology and on-land threats of Cape Verde petrel (Pterodroma feae) in Fogo Island, Cape Verde.

PubMed

Militão, Teresa; Dinis, Herculano Andrade; Zango, Laura; Calabuig, Pascual; Stefan, Laura M; González-Solís, Jacob

2017-01-01

Cape Verde petrel (Pterodroma feae) is currently considered near threatened, but little is known about its population size, breeding biology and on land threats, jeopardizing its management and conservation. To improve this situation, we captured, marked and recaptured (CMR) birds using mist-nets over 10 years; measured and sexed them; monitored up to 14 burrows, deployed GPS devices on breeders and analyzed activity data of geolocators retrieved from breeders in Fogo (Cape Verde). We set cat traps over the colony and investigated their domestic/feral origin by marking domestic cats from a nearby village with transponders, by deploying GPS devices on domestic cats and by performing stable isotope analyses of fur of the trapped and domestic cats. The population of Fogo was estimated to be 293 birds, including immatures (95% CI: 233-254, CMR modelling). Based on geolocator activity data and nest monitoring we determined the breeding phenology of this species and we found biometric differences between sexes. While monitoring breeding performance, we verified a still ongoing cat predation and human harvesting. Overall, data gathered from trapped cats without transponder, cats GPS trips and the distinct isotopic values between domestic and trapped cats suggest cats visiting the colony are of feral origin. GPS tracks from breeders showed birds left and returned to the colony using the sector NE of the islands, where high level of public lights should be avoided specially during the fledging period. Main threats for the Cape Verde petrel in the remaining breeding islands are currently unknown but likely to be similar to Fogo, calling for an urgent assessment of population trends and the control of main threats in all Cape Verde Islands and uplisting its conservation status.

Restoration of Pulsatile Flow Reduces Sympathetic Nerve Activity Among Individuals With Continuous-Flow Left Ventricular Assist Devices.

PubMed

Cornwell, William K; Tarumi, Takashi; Stickford, Abigail; Lawley, Justin; Roberts, Monique; Parker, Rosemary; Fitzsimmons, Catherine; Kibe, Julius; Ayers, Colby; Markham, David; Drazner, Mark H; Fu, Qi; Levine, Benjamin D

2015-12-15

Current-generation left ventricular assist devices provide circulatory support that is minimally or entirely nonpulsatile and are associated with marked increases in muscle sympathetic nerve activity (MSNA), likely through a baroreceptor-mediated pathway. We sought to determine whether the restoration of pulsatile flow through modulations in pump speed would reduce MSNA through the arterial baroreceptor reflex. Ten men and 3 women (54 ± 14 years) with Heartmate II continuous-flow left ventricular assist devices underwent hemodynamic and sympathetic neural assessment. Beat-to-beat blood pressure, carotid ultrasonography at the level of the arterial baroreceptors, and MSNA via microneurography were continuously recorded to determine steady-state responses to step changes (200-400 revolutions per minute) in continuous-flow left ventricular assist device pump speed from a maximum of 10,480 ± 315 revolutions per minute to a minimum of 8500 ± 380 revolutions per minute. Reductions in pump speed led to increases in pulse pressure (high versus low speed: 17 ± 7 versus 26 ± 12 mm Hg; P<0.01), distension of the carotid artery, and carotid arterial wall tension (P<0.05 for all measures). In addition, MSNA was reduced (high versus low speed: 41 ± 15 versus 33 ± 16 bursts per minute; P<0.01) despite a reduction in mean arterial pressure and was inversely related to pulse pressure (P=0.037). Among subjects with continuous-flow left ventricular assist devices, the restoration of pulsatile flow through modulations in pump speed leads to increased distortion of the arterial baroreceptors with a subsequent decline in MSNA. Additional study is needed to determine whether reduction of MSNA in this setting leads to improved outcomes. © 2015 American Heart Association, Inc.

Enhancements to a Superconducting Quantum Interference Device (SQUID) Multiplexer Readout and Control System

NASA Technical Reports Server (NTRS)

Forgione, J.; Benford, D. J.; Buchanan, E. D.; Moseley, S. H.; Rebar, J.; Shafer, R. A.

2004-01-01

Far-infrared detector arrays such as the 16x32 superconducting bolometer array for the SAFIRE instrument (flying on the SOFIA airborne observatory) require systems of readout and control electronics to provide translation between a user-driven, digital PC and the cold, analog world of the cryogenic detector. In 2001, the National Institute of Standards and Technology (NIST) developed their Mark III electronics for purposes of control and readout of their 1x32 SQUID Multiplexer chips. We at NASA s Goddard Space Flight Center acquired a Mark 111 system and subsequently designed upgrades to suit our and our collaborators purposes. We developed an arbitrary, programmable multiplexing system that allows the user to cycle through rows in a SQUID array in an infinite number of combinations. We provided hooks in the Mark III system to allow readout of signals from outside the Mark 111 system, such as telescope status information. Finally, we augmented the heart of the system with a new feedback algorithm implementation, flexible diagnostic tools, and informative telemetry.

Enhancements to a superconducting quantum interference device (SQUID) multiplexer readout and control system

NASA Astrophysics Data System (ADS)

Forgione, Joshua B.; Benford, Dominic J.; Buchanan, Ernest D.; Moseley, S. H., Jr.; Rebar, Joyce; Shafer, Richard A.

2004-10-01

Far-infrared detector arrays such as the 16x32 superconducting bolometer array for the SAFIRE instrument (flying on the SOFIA airborne observatory) require systems of readout and control electronics to provide translation between a user-driven, digital PC and the cold, analog world of the cryogenic detector. In 2001, the National Institute of Standards and Technology (NIST) developed their Mark III electronics for purposes of control and readout of their 1x32 SQUID Multiplexer chips. We at NASA's Goddard Space Flight Center acquired a Mark III system and subsequently designed upgrades to suit our and our collaborators' purposes. We developed an arbitrary, programmable multiplexing system that allows the user to cycle through rows in a SQUID array in an infinite number of combinations. We provided 'hooks' in the Mark III system to allow readout of signals from outside the Mark III system, such as telescope status information. Finally, we augmented the heart of the system with a new feedback algorithm implementation, flexible diagnostic tools, and informative telemetry.

Multilayer Microfluidic Devices Created From A Single Photomask

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kelly, Ryan T.; Sheen, Allison M.; Jambovane, Sachin R.

2013-08-28

The time and expense associated with high quality photomask production can discourage the creation of multilayer microfluidic devices, as each layer currently requires a separate photomask. Here we describe an approach in which multilayer microfabricated devices can be created from a single photomask. The separate layers and their corresponding alignment marks are arranged in separate halves of the mask for two layer devices or quadrants for four layer devices. Selective exposure of the photomask features and rotation of the device substrate between exposures result in multiple copies of the devices on each wafer. Subsequent layers are aligned to patterned featuresmore » on the substrate with the same alignment accuracy as when multiple photomasks are used. We demonstrate this approach for fabricating devices employing multilayer soft lithography (MSL) for pneumatic valving. MSL devices containing as many as 5 layers (4 aligned fluidic layers plus a manually aligned control layer) were successfully created using this approach. Device design is also modularized, enabling the presence or absence of features as well as channel heights to be selected independently from one another. The use of a single photomask to create multilayer devices results in a dramatic savings of time and/or money required to advance from device design to completed prototype.« less

21 CFR 886.1450 - Corneal radius measuring device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Corneal radius measuring device. 886.1450 Section... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1450 Corneal radius measuring device. (a) Identification. A corneal radius measuring device is an AC-powered device intended to measure...

[Requirements for CE-marking of apps and wearables].

PubMed

Berensmann, Michael; Gratzfeld, Markus

2018-03-01

Depending on the intended use, apps and wearables can be medical devices. In such cases, the manufacturer has to provide evidence that the requirements stated in directive 93/42/EWG are fulfilled. Depending on the classification of the medical device, several so-called conformity assessment procedures are possible. Once the conformity assessment procedure has been finished successfully, the manufacturer attaches the CE-marking to the product. This assures that all requirements of the directive have been fulfilled and the manufacturer is therefore authorized to put the product onto the market in all member states of the European union. In this article, the possible and practical conformity assessment procedures for apps and wearables are described and their implementation is outlined.For medical devices with sufficiently high-risk classification, the manufacturer has to involve a Notified Body. For the conformity assessment procedure according to annex II, the manufacturer implements a full quality management system and compiles technical documentation. These are supervised and evaluated by Notified Body audits. Especially for startups, it is important for the development of apps and wearables to implement a quality management system early and to fulfill the regulatory requirements, for example, related to the software life-cycle model. This also includes considering accompanying processes during development like risk management, usability engineering, and clinical evaluation.Additionally, it should be pointed out, that according to the new medical device regulation almost all apps will fall at least into class IIa. Thus, the involvement of a Notified Body in the related conformity assessment procedures would be required. Apps that have already been put onto the market as class I devices, and are now upgraded to a higher class, need the approval of a notified body starting from 26 May 2020.

Porcine endogenous retroviral nucleic acid in peripheral tissues is associated with migration of porcine cells post islet transplant.

PubMed

Binette, Tanya M; Seeberger, Karen L; Lyon, James G; Rajotte, Ray V; Korbutt, Gregory S

2004-07-01

Porcine islets represent an alternative source of insulin-producing tissue, however, porcine endogenous retrovirus (PERV) remains a concern. In this study, SCID mice were transplanted with nonencapsulated (non-EC), microencapsulated (EC) or macroencapsulated (in a TheraCyte trade mark device) neonatal porcine islets (NPIs), and peripheral tissues were screened for presence of viral DNA and mRNA. To understand the role of an intact immune system in PERV incidence, mice with established NPI grafts were reconstituted with splenocytes. Peripheral tissues were screened for PERV and porcine DNA using PCR. Tissues with positive DNA were analyzed for PERV mRNA using RT-PCR. No significant difference was observed between non-EC and EC transplants regarding presence of PERV or porcine-specific DNA or mRNA. In reconstituted animals, little PERV or porcine DNA, and no PERV mRNA was detected. No PERV or porcine-specific DNA was observed in animals implanted with a TheraCyte trade mark device. In conclusion, an intact immune system significantly lowered the presence of PERV. Microencapsulation of islets did not alter PERV presence, however, macroencapsulation in the TheraCyte device did. Lower PERV incidence coincided with lower porcine DNA in peripheral tissues, linking the presence of PERV to migration of porcine cells.

Modeling light

NASA Astrophysics Data System (ADS)

Dawson, P.; Gage, J.; Takatsuka, M.; Goyette, S.

2009-02-01

To compete with other digital images, holograms must go beyond the current range of source-image types, such as sequences of photographs, laser scans, and 3D computer graphics (CG) scenes made with software designed for other applications. This project develops a set of innovative techniques for creating 3D digital content specifically for digital holograms, with virtual tools which enable the direct hand-crafting of subjects, mark by mark, analogous to Michelangelo's practice in drawing, painting and sculpture. The haptic device, the Phantom Premium 1.5 is used to draw against three-dimensional laser- scan templates of Michelangelo's sculpture placed within the holographic viewing volume.

Roadway Marking Optics for Autonomous Vehicle Guidance and Other Machine Vision Applications

NASA Astrophysics Data System (ADS)

Konopka, Anthony T.

This work determines optimal planar geometric light source and optical imager configurations and electromagnetic wavelengths for maximizing the reflected signal intensity when using machine vision technology to image roadway markings with embedded spherical glass beads. It is found through a first set of experiments that roadway marking samples exhibiting little or no bead rolling effects are uniformly reflective with respect to the azimuthal angle of observation when measured for retroreflectivity within industry standard 30-meter geometry. A second set of experiments indicate that white roadway markings exhibit higher reflectivity throughout the visible spectrum than yellow roadway markings. A roadway marking optical model capable of being used to determine optimal geometric light source and optical imager configurations for maximizing the reflected signal intensities of roadway marking targets is constructed and simulated using optical engineering software. It is found through a third set of experiments that high signal intensities can be measured when the polar angles of the light source and optical imager along a plane normal to a roadway marking are equal, with the maximum signal intensity being measured when the polar angles of both the light source and optical imager are 90°.

Relevance of Trust Marks and CE Labels in German-Language Store Descriptions of Health Apps: Analysis

PubMed Central

Hillebrand, Uta; von Jan, Ute

2018-01-01

Background In addition to mandatory CE marking (“CE” representing Conformité Européenne, with the CE marking being a symbol of free marketability in the European Economic Area) for medical devices, there are various seals, initiatives, action groups, etc, in the health app context. However, whether manufacturers use them to distinguish their apps and attach relevance to them is unclear. Objective The objective was to take a snapshot of quality seals, regulatory marks, and other orientation aids available on the German app market and to determine whether manufacturers deem such labels relevant enough to apply them to their apps, namely as reflected by mentions in app description texts in a typical app store (ie, Apple’s App Store). Methods A full survey of the metadata of 103,046 apps from Apple’s German App Store in the Medicine and Health & Fitness categories was carried out. For apps with German-language store descriptions (N=8767), these were automatically searched for the occurrence of relevant keywords and validated manually (N=41). In addition, the websites of various app seal providers were checked for assigned seals. Results Few manufacturers referenced seals in the descriptions (5/41), although this would have been expected more often based on the seals we were able to identify from the seal providers’ Web pages, and there were 34 of 41 that mentioned CE status in the descriptions. Two apps referenced an app directory curated by experts; however, this is not an alternative to CE marks and seals of approval. Conclusions Currently, quality seals seem to be irrelevant for manufacturers. In line with regulatory requirements, mentions of medical device status are more frequent; however, neither characteristic is effective for identifying high-quality apps. To improve this situation, a possibly legally obligatory, standardized reporting system should be implemented. PMID:29695374

Relevance of Trust Marks and CE Labels in German-Language Store Descriptions of Health Apps: Analysis.

PubMed

Albrecht, Urs-Vito; Hillebrand, Uta; von Jan, Ute

2018-04-25

In addition to mandatory CE marking ("CE" representing Conformité Européenne, with the CE marking being a symbol of free marketability in the European Economic Area) for medical devices, there are various seals, initiatives, action groups, etc, in the health app context. However, whether manufacturers use them to distinguish their apps and attach relevance to them is unclear. The objective was to take a snapshot of quality seals, regulatory marks, and other orientation aids available on the German app market and to determine whether manufacturers deem such labels relevant enough to apply them to their apps, namely as reflected by mentions in app description texts in a typical app store (ie, Apple's App Store). A full survey of the metadata of 103,046 apps from Apple's German App Store in the Medicine and Health & Fitness categories was carried out. For apps with German-language store descriptions (N=8767), these were automatically searched for the occurrence of relevant keywords and validated manually (N=41). In addition, the websites of various app seal providers were checked for assigned seals. Few manufacturers referenced seals in the descriptions (5/41), although this would have been expected more often based on the seals we were able to identify from the seal providers' Web pages, and there were 34 of 41 that mentioned CE status in the descriptions. Two apps referenced an app directory curated by experts; however, this is not an alternative to CE marks and seals of approval. Currently, quality seals seem to be irrelevant for manufacturers. In line with regulatory requirements, mentions of medical device status are more frequent; however, neither characteristic is effective for identifying high-quality apps. To improve this situation, a possibly legally obligatory, standardized reporting system should be implemented. ©Urs-Vito Albrecht, Uta Hillebrand, Ute von Jan. Originally published in JMIR Mhealth and Uhealth (http://mhealth.jmir.org), 25.04.2018.

77 FR 60677 - Proposed Information Collection; Comment Request; Antarctic Marine Living Resources Conservation...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-04

... DC 20230 (or via Internet at [email protected] ). FOR FURTHER INFORMATION CONTACT: Requests for..., electronic reports, satellite-linked vessel monitoring devices, radio and telephone calls, gear and vessel markings are required from participants and methods of transmittal include Internet, satellite, facsimile...

46 CFR 151.50-30 - Compressed gases.

Code of Federal Regulations, 2011 CFR

2011-10-01

... BULK LIQUID HAZARDOUS MATERIAL CARGOES Special Requirements § 151.50-30 Compressed gases. (a) All tank inlet and outlet connections, except safety relief valves, liquid level gauging devices, and pressure gauges shall be marked to designate whether they terminate in the vapor or liquid space. Labels, when...

46 CFR 151.50-30 - Compressed gases.

Code of Federal Regulations, 2014 CFR

2014-10-01

... BULK LIQUID HAZARDOUS MATERIAL CARGOES Special Requirements § 151.50-30 Compressed gases. (a) All tank inlet and outlet connections, except safety relief valves, liquid level gauging devices, and pressure gauges shall be marked to designate whether they terminate in the vapor or liquid space. Labels, when...

46 CFR 151.50-30 - Compressed gases.

Code of Federal Regulations, 2012 CFR

2012-10-01

... BULK LIQUID HAZARDOUS MATERIAL CARGOES Special Requirements § 151.50-30 Compressed gases. (a) All tank inlet and outlet connections, except safety relief valves, liquid level gauging devices, and pressure gauges shall be marked to designate whether they terminate in the vapor or liquid space. Labels, when...

46 CFR 151.50-30 - Compressed gases.

Code of Federal Regulations, 2013 CFR

2013-10-01

... BULK LIQUID HAZARDOUS MATERIAL CARGOES Special Requirements § 151.50-30 Compressed gases. (a) All tank inlet and outlet connections, except safety relief valves, liquid level gauging devices, and pressure gauges shall be marked to designate whether they terminate in the vapor or liquid space. Labels, when...

46 CFR 151.50-30 - Compressed gases.

Code of Federal Regulations, 2010 CFR

2010-10-01

... BULK LIQUID HAZARDOUS MATERIAL CARGOES Special Requirements § 151.50-30 Compressed gases. (a) All tank inlet and outlet connections, except safety relief valves, liquid level gauging devices, and pressure gauges shall be marked to designate whether they terminate in the vapor or liquid space. Labels, when...

9 CFR 317.400 - Exemption from nutrition labeling.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 9 Animals and Animal Products 2 2013-01-01 2013-01-01 false Exemption from nutrition labeling. 317... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.400 Exemption from nutrition labeling. (a) The following meat or meat food products are exempt from nutrition...

9 CFR 317.309 - Nutrition label content.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Nutrition label content. 317.309... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.309 Nutrition... program qualify for nutrition claims. (3) The declaration of nutrient and food component content shall be...

9 CFR 317.400 - Exemption from nutrition labeling.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 9 Animals and Animal Products 2 2014-01-01 2014-01-01 false Exemption from nutrition labeling. 317... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.400 Exemption from nutrition labeling. (a) The following meat or meat food products are exempt from nutrition...

9 CFR 317.309 - Nutrition label content.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 9 Animals and Animal Products 2 2014-01-01 2014-01-01 false Nutrition label content. 317.309... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.309 Nutrition... only through a weight-control program qualify for nutrition claims. (3) The declaration of nutrient and...

9 CFR 317.309 - Nutrition label content.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 9 Animals and Animal Products 2 2013-01-01 2013-01-01 false Nutrition label content. 317.309... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.309 Nutrition... only through a weight-control program qualify for nutrition claims. (3) The declaration of nutrient and...

9 CFR 317.400 - Exemption from nutrition labeling.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Exemption from nutrition labeling. 317... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.400 Exemption from nutrition labeling. (a) The following meat or meat food products are exempt from nutrition...

9 CFR 317.309 - Nutrition label content.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 9 Animals and Animal Products 2 2012-01-01 2012-01-01 false Nutrition label content. 317.309... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.309 Nutrition... program qualify for nutrition claims. (3) The declaration of nutrient and food component content shall be...

"Just Remember This": Lexicogrammatical Relevance Markers in Lectures

ERIC Educational Resources Information Center

Deroey, Katrien L. B.; Taverniers, Miriam

2012-01-01

This paper presents a comprehensive overview of lexicogrammatical devices which highlight important or relevant points in lectures. Despite the established usefulness of discourse organizational cues for lecture comprehension and note-taking, very little is known about the marking of relevance in this genre. The current overview of…

A Single-Molecule Barcoding System using Nanoslits for DNA Analysis

NASA Astrophysics Data System (ADS)

Jo, Kyubong; Schramm, Timothy M.; Schwartz, David C.

Single DNA molecule approaches are playing an increasingly central role in the analytical genomic sciences because single molecule techniques intrinsically provide individualized measurements of selected molecules, free from the constraints of bulk techniques, which blindly average noise and mask the presence of minor analyte components. Accordingly, a principal challenge that must be addressed by all single molecule approaches aimed at genome analysis is how to immobilize and manipulate DNA molecules for measurements that foster construction of large, biologically relevant data sets. For meeting this challenge, this chapter discusses an integrated approach for microfabricated and nanofabricated devices for the manipulation of elongated DNA molecules within nanoscale geometries. Ideally, large DNA coils stretch via nanoconfinement when channel dimensions are within tens of nanometers. Importantly, stretched, often immobilized, DNA molecules spanning hundreds of kilobase pairs are required by all analytical platforms working with large genomic substrates because imaging techniques acquire sequence information from molecules that normally exist in free solution as unrevealing random coils resembling floppy balls of yarn. However, nanoscale devices fabricated with sufficiently small dimensions fostering molecular stretching make these devices impractical because of the requirement of exotic fabrication technologies, costly materials, and poor operational efficiencies. In this chapter, such problems are addressed by discussion of a new approach to DNA presentation and analysis that establishes scaleable nanoconfinement conditions through reduction of ionic strength; stiffening DNA molecules thus enabling their arraying for analysis using easily fabricated devices that can also be mass produced. This new approach to DNA nanoconfinement is complemented by the development of a novel labeling scheme for reliable marking of individual molecules with fluorochrome labels, creating molecular barcodes, which are efficiently read using fluorescence resonance energy transfer techniques for minimizing noise from unincorporated labels. As such, our integrative approach for the realization of genomic analysis through nanoconfinement, named nanocoding, was demonstrated through the barcoding and mapping of bacterial artificial chromosomal molecules, thereby providing the basis for a high-throughput platform competent for whole genome investigations.

Real-time Magnetic Resonance Imaging Guidance for Cardiovascular Procedures

PubMed Central

Horvath, Keith A.; Li, Ming; Mazilu, Dumitru; Guttman, Michael A.; McVeigh, Elliot R.

2008-01-01

Magnetic resonance imaging (MRI) of the cardiovascular system has proven to be an invaluable diagnostic tool. Given the ability to allow for real-time imaging, MRI guidance of intraoperative procedures can provide superb visualization which can facilitate a variety of interventions and minimize the trauma of the operations as well. In addition to the anatomic detail, MRI can provide intraoperative assessment of organ and device function. Instruments and devices can be marked to enhance visualization and tracking. All of which is an advance over standard x-ray or ultrasonic imaging. PMID:18395633

Commissioning of the new GMOS-N Hamamatsu CCDs

NASA Astrophysics Data System (ADS)

Scharwaechter, Julia; Chiboucas, Kristin; Gimeno, German; Boucher, Luc; White, John; Tapia, Eduardo; Lundquist, Michael; Rippa, Mathew; Labrie, Kathleen; Murowinski, Richard; Lazo, Manuel; Miller, Jennifer

2017-06-01

We report on the commissioning of the new Hamamatsu fully-depleted CCDs for GMOS-N, installed in the instrument in February 2017. The Hamamatsu detectors replace the e2v deep depletion devices which had been in operation since 2011. The new GMOS-N detector array is expected to provide improved red sensitivity compared to the e2v devices at wavelengths longer than ~900 nm. The commissioning of the new detector array for GMOS-N marks the final step in upgrading the two GMOS instruments at Gemini North and South with Hamamatsu detectors.

Spectrally resolved hyperfine interactions between polaron and nuclear spins in organic light emitting diodes: Magneto-electroluminescence studies

NASA Astrophysics Data System (ADS)

Crooker, S. A.; Liu, F.; Kelley, M. R.; Martinez, N. J. D.; Nie, W.; Mohite, A.; Nayyar, I. H.; Tretiak, S.; Smith, D. L.; Ruden, P. P.

2014-10-01

We use spectrally resolved magneto-electroluminescence (EL) measurements to study the energy dependence of hyperfine interactions between polaron and nuclear spins in organic light-emitting diodes. Using layered devices that generate bright exciplex emission, we show that the increase in EL emission intensity I due to small applied magnetic fields of order 100 mT is markedly larger at the high-energy blue end of the EL spectrum (ΔI/I ˜ 11%) than at the low-energy red end (˜4%). Concurrently, the widths of the magneto-EL curves increase monotonically from blue to red, revealing an increasing hyperfine coupling between polarons and nuclei and directly providing insight into the energy-dependent spatial extent and localization of polarons.

Molecular Diode Studies Based on a Highly Sensitive Molecular Measurement Technique.

PubMed

Iwane, Madoka; Fujii, Shintaro; Kiguchi, Manabu

2017-04-26

In 1974, molecular electronics pioneers Mark Ratner and Arieh Aviram predicted that a single molecule could act as a diode, in which electronic current can be rectified. The electronic rectification property of the diode is one of basic functions of electronic components and since then, the molecular diode has been investigated as a first single-molecule device that would have a practical application. In this review, we first describe the experimental fabrication and electronic characterization techniques of molecular diodes consisting of a small number of molecules or a single molecule. Then, two main mechanisms of the rectification property of the molecular diode are discussed. Finally, representative results for the molecular diode are reviewed and a brief outlook on crucial issues that need to be addressed in future research is discussed.

Molecular Diode Studies Based on a Highly Sensitive Molecular Measurement Technique

PubMed Central

Iwane, Madoka; Fujii, Shintaro; Kiguchi, Manabu

2017-01-01

In 1974, molecular electronics pioneers Mark Ratner and Arieh Aviram predicted that a single molecule could act as a diode, in which electronic current can be rectified. The electronic rectification property of the diode is one of basic functions of electronic components and since then, the molecular diode has been investigated as a first single-molecule device that would have a practical application. In this review, we first describe the experimental fabrication and electronic characterization techniques of molecular diodes consisting of a small number of molecules or a single molecule. Then, two main mechanisms of the rectification property of the molecular diode are discussed. Finally, representative results for the molecular diode are reviewed and a brief outlook on crucial issues that need to be addressed in future research is discussed. PMID:28445393

21 CFR 882.1560 - Skin potential measurement device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Skin potential measurement device. 882.1560... (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882.1560 Skin potential measurement device. (a) Identification. A skin potential measurement device is a general diagnostic device...

21 CFR 882.1560 - Skin potential measurement device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Skin potential measurement device. 882.1560... (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882.1560 Skin potential measurement device. (a) Identification. A skin potential measurement device is a general diagnostic device...

21 CFR 882.1560 - Skin potential measurement device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Skin potential measurement device. 882.1560... (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882.1560 Skin potential measurement device. (a) Identification. A skin potential measurement device is a general diagnostic device...

21 CFR 882.1560 - Skin potential measurement device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Skin potential measurement device. 882.1560... (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882.1560 Skin potential measurement device. (a) Identification. A skin potential measurement device is a general diagnostic device...

Preliminary Vibration Measurements on Mark I Vehicle

DOT National Transportation Integrated Search

1971-01-01

Preliminary measurements have been made on the acceleration and vibration environment of the Mark I vehicle while operating on the New York City Transit System. Measurements at the journal box indicated shor period high acceleration pulses as lage as...

The Bionic Clicker Mark I & II

PubMed Central

Magee, Elliott G.; Ourselin, S.; Nikitichev, Daniil; Vercauteren, T.; Vanhoestenberghe, Anne

2017-01-01

In this manuscript, we present two 'Bionic Clicker' systems, the first designed to demonstrate electromyography (EMG) based control systems for educational purposes and the second for research purposes. EMG based control systems pick up electrical signals generated by muscle activation and use these as inputs for controllers. EMG controllers are widely used in prosthetics to control limbs. The Mark I (MK I) clicker allows the wearer to change the slide of a presentation by raising their index finger. It is built around a microcontroller and a bio-signals shield. It generated a lot of interest from both the public and research community. The Mark II (MK II) device presented here was designed to be a cheaper, sleeker, and more customizable system that can be easily modified and directly transmit EMG data. It is built using a wireless capable microcontroller and a muscle sensor. PMID:28829413

The Bionic Clicker Mark I & II.

PubMed

Magee, Elliott G; Ourselin, S; Nikitichev, Daniil; Vercauteren, T; Vanhoestenberghe, Anne

2017-08-14

In this manuscript, we present two 'Bionic Clicker' systems, the first designed to demonstrate electromyography (EMG) based control systems for educational purposes and the second for research purposes. EMG based control systems pick up electrical signals generated by muscle activation and use these as inputs for controllers. EMG controllers are widely used in prosthetics to control limbs. The Mark I (MK I) clicker allows the wearer to change the slide of a presentation by raising their index finger. It is built around a microcontroller and a bio-signals shield. It generated a lot of interest from both the public and research community. The Mark II (MK II) device presented here was designed to be a cheaper, sleeker, and more customizable system that can be easily modified and directly transmit EMG data. It is built using a wireless capable microcontroller and a muscle sensor.

The baric probe: a novel long-term implantable intracranial pressure monitor with ultrasound-based interrogation.

PubMed

Limbrick, David D; Lake, Stephen; Talcott, Michael; Alexander, Benjamin; Wight, Samuel; Willie, Jon T; Richard, William D; Genin, Guy M; Leuthardt, Eric C

2012-12-01

Prompt diagnosis of shunt malfunction is critical in preventing neurological morbidity and death in individuals with hydrocephalus; however, diagnostic methods for this condition remain limited. For several decades, investigators have sought a long-term, implantable intracranial pressure (ICP) monitor to assist in the diagnosis of shunt malfunction, but efforts have been impeded by device complexity, marked measurement drift, and limited instrumentation lifespan. In the current report, the authors introduce an entirely novel, simple, compressible gas design that addresses each of these problems. The device described herein, termed the "baric probe," consists of a subdural fluid bladder and multichannel indicator that monitors the position of an air-fluid interface (AFI). A handheld ultrasound probe is used to interrogate the baric probe in vivo, permitting noninvasive ICP determination. To assess the function of device prototypes, ex vivo experiments were conducted using a water column, and short- and long-term in vivo experiments were performed using a porcine model with concurrent measurements of ICP via a fiberoptic monitor. Following a toe region of approximately 2 cm H(2)O, the baric probe's AFI demonstrated a predictable linear relationship to ICP in both ex vivo and in vivo models. After a 2-week implantation of the device, this linear relationship remained robust and reproducible. Further, changes in ICP were observed with the baric probe, on average, 3 seconds in advance of the fiberoptic ICP monitor reading. The authors demonstrate "proof-of-concept" and feasibility for the baric probe, a long-term implantable ICP monitor designed to facilitate the prompt and accurate diagnosis of shunt malfunction. The baric probe showed a consistent linear relationship between ICP and the device's AFI in ex vivo and short- and long-term in vivo models. With a low per-unit cost, a reduced need for radiography or CT, and an indicator that can be read with a handheld ultrasound probe that interfaces with any smart phone, the baric probe promises to simplify the care of patients with shunt-treated hydrocephalus throughout both the developed and the developing world.

Transcatheter aortic valve replacement with new-generation devices: A systematic review and meta-analysis.

PubMed

Barbanti, Marco; Buccheri, Sergio; Rodés-Cabau, Josep; Gulino, Simona; Généreux, Philippe; Pilato, Gerlando; Dvir, Danny; Picci, Andrea; Costa, Giuliano; Tamburino, Corrado; Leon, Martin B; Webb, John G

2017-10-15

The aim of this study was to conduct a weighted meta-analysis to determine the rates of acute (≤30days) major outcomes after (TAVR) with second-generation devices. A comprehensive search of multiple electronic databases from January 2011 to May 2017 was conducted using predefined criteria. New-generation TAVR devices were defined as any device which received CE mark approval or is still under evaluation for CE marking after CoreValve and SAPIEN XT prostheses. A total of 37 studies including 10,822 patients met inclusion criteria and were included in the analysis. Devices investigated in the studies were the following: SAPIEN 3 (n=5423, 45.9%), Lotus Valve (n=3007, %), Portico (n=130, 1.1%), JenaValve (n=345, 2.9%), Symetis Acurate (n=1314, 11,1%), and Evolut R (n=1603, 13.6%). Thirty-day all-cause and cardiovascular 30-day death were 2.2% (95% CI: 1.6% to 2.8%) and 1.6% (95% CI: 0.9% to 2.3%), respectively; Any stroke and major/disabling stroke occurred at a pooled estimate rate of 2.6% (95% CI: 2.0% to 3.3%) and 0.9% (95% CI: 0.2% to 1.6%), respectively; life-threatening bleeding, 3.9% (95% CI: 2.9% to 5.0%); major vascular complications, 4.5% (95% CI: 3.7% to 5.4%); pacemaker implantation, 16.2% (95% CI: 12.7% to 19.6%); more than mild aortic regurgitation, 1.6% (95% CI: 0.9 to 2.3). Second-generation TAVR devices are associated with very low mortality and major complications rates at 30-day, and improved prosthesis performance with <2% of patients having more than mild post-procedural aortic regurgitation. On the other hand, the need for pacemaker implantation seems to remain an unresolved issue, and warrants further investigation. Copyright © 2017 Elsevier B.V. All rights reserved.

Exploring interface morphology of a deeply buried layer in periodic multilayer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Das, Gangadhar; Srivastava, A. K.; Tiwari, M. K., E-mail: mktiwari@rrcat.gov.in

2016-06-27

Long-term durability of a thin film device is strongly correlated with the nature of interface structure associated between different constituent layers. Synthetic periodic multilayer structures are primarily employed as artificial X-ray Bragg reflectors in many applications, and their reflection efficiency is predominantly dictated by the nature of the buried interfaces between the different layers. Herein, we demonstrate the applicability of the combined analysis approach of the X-ray reflectivity and grazing incidence X-ray fluorescence measurements for the reliable and precise determination of a buried interface structure inside periodic X-ray multilayer structures. X-ray standing wave field (XSW) generated under Bragg reflection conditionmore » is used to probe the different constituent layers of the W- B{sub 4}C multilayer structure at 10 keV and 12 keV incident X-ray energies. Our results show that the XSW assisted fluorescence measurements are markedly sensitive to the location and interface morphology of a buried layer structure inside a periodic multilayer structure. The cross sectional transmission electron microscopy results obtained on the W-B{sub 4}C multilayer structure provide a deeper look on the overall reliability and accuracy of the XSW method. The method described here would also be applicable for nondestructive characterization of a wide range of thin film based semiconductor and optical devices.« less

A novel sidestream ultrasonic flow sensor for multiple breath washout in children.

PubMed

Fuchs, Susanne I; Sturz, J; Junge, S; Ballmann, M; Gappa, M

2008-08-01

Inert gas multiple breath washout (MBW) for measuring Lung Clearance Index using mass spectrometry and 4% sulfur hexafluoride (SF(6)) as the tracer gas has been shown to be sensitive for detecting early Cystic Fibrosis (CF) lung disease. However, mass spectrometry requires bulky equipment and is expensive to buy and maintain. A novel sidestream ultrasonic device may overcome this problem. The aims of this study were to assess the feasibility and clinical validity of measuring lung volume (functional residual capacity, FRC) and the LCI using the sidestream ultrasonic flow sensor in children and adolescents with CF in relation to spirometry and plain chest radiographs. MBW using the sidestream ultrasonic device and conventional spirometry were performed in 26 patients with CF and 22 healthy controls. In the controls (4.7-17.7 years) LCI was similar to that reported using mass spectrometry (mean (SD) 6.7 (0.5)). LCI was elevated in 77% of the CF children (6.8-18.9 years), whereas spirometry was abnormal in only 38.5%, 61.5%, and 26.9% for FEV(1), MEF(25), and FEV(1)/FVC, respectively. This was more marked in children <10 years. LCI correlated with the Crispin-Norman score, whereas FEV(1) did not. Sidestream ultrasonic MBW is a valid and simple alternative to mass spectrometry for assessing ventilation homogeneity in children. (c) 2008 Wiley-Liss, Inc.

9 CFR 317.369 - Labeling applications for nutrient content claims.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AND VOLUNTARY INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition... of the food component characterized by the claim is of importance in human nutrition by virtue of its... intake of nutrients that have beneficial and negative consequences in the total diet. If the claim is...

9 CFR 317.369 - Labeling applications for nutrient content claims.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AND VOLUNTARY INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition... of the food component characterized by the claim is of importance in human nutrition by virtue of its... intake of nutrients that have beneficial and negative consequences in the total diet. If the claim is...

9 CFR 317.369 - Labeling applications for nutrient content claims.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AND VOLUNTARY INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition... of the food component characterized by the claim is of importance in human nutrition by virtue of its... intake of nutrients that have beneficial and negative consequences in the total diet. If the claim is...

9 CFR 317.369 - Labeling applications for nutrient content claims.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AND VOLUNTARY INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition... of the food component characterized by the claim is of importance in human nutrition by virtue of its... intake of nutrients that have beneficial and negative consequences in the total diet. If the claim is...

29 CFR 1915.100 - Retention of DOT markings, placards and labels.

Code of Federal Regulations, 2011 CFR

2011-07-01

... are readily visible. (d) For non-bulk packages which will not be reshipped, the provisions of this... permanently alter its energy-control capability. (5) Contract employer. An employer, such as a painting... isolate energy. Control-circuit devices (for example, push buttons, selector switches) are not considered...

Minimizing morbidity of hypoglycemia in diabetes: A review of mini-dose glucagon

USDA-ARS?s Scientific Manuscript database

Type 1 diabetes is a common chronic disease of childhood and one of the most difficult conditions to manage. Advances in insulin formulations and insulin delivery devices have markedly improved the ability to achieve normal glucose homeostasis. However, hypoglycemia remains the primary limiting fact...

9 CFR 317.302 - Location of nutrition information.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 9 Animals and Animal Products 2 2014-01-01 2014-01-01 false Location of nutrition information. 317... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.302 Location of nutrition information. (a) Nutrition information on a label of a packaged meat or meat food...

9 CFR 317.300 - Nutrition labeling of meat or meat food products.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Nutrition labeling of meat or meat... AND VOLUNTARY INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.300 Nutrition labeling of meat or meat food products. (a) Nutrition labeling shall be...

9 CFR 317.300 - Nutrition labeling of meat and meat food products.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 9 Animals and Animal Products 2 2014-01-01 2014-01-01 false Nutrition labeling of meat and meat... AND VOLUNTARY INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.300 Nutrition labeling of meat and meat food products. (a) Nutrition labeling must be...

9 CFR 317.400 - Exemption from nutrition labeling.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Exemption from nutrition labeling. 317... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.400 Exemption from nutrition labeling. Link to an amendment published at 75 FR 82165, Dec. 29, 2010. (a) The...

9 CFR 317.400 - Exemption from nutrition labeling.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 9 Animals and Animal Products 2 2012-01-01 2012-01-01 false Exemption from nutrition labeling. 317... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.400 Exemption from nutrition labeling. Link to an amendment published at 75 FR 82165, Dec. 29, 2010. This amendment...

9 CFR 317.300 - Nutrition labeling of meat and meat food products.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 9 Animals and Animal Products 2 2013-01-01 2013-01-01 false Nutrition labeling of meat and meat... AND VOLUNTARY INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.300 Nutrition labeling of meat and meat food products. (a) Nutrition labeling must be...

9 CFR 317.302 - Location of nutrition information.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Location of nutrition information. 317... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.302 Location of nutrition information. (a) Nutrition information on a label of a packaged meat or meat food...

9 CFR 317.302 - Location of nutrition information.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 9 Animals and Animal Products 2 2013-01-01 2013-01-01 false Location of nutrition information. 317... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.302 Location of nutrition information. (a) Nutrition information on a label of a packaged meat or meat food...

9 CFR 317.302 - Location of nutrition information.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 9 Animals and Animal Products 2 2012-01-01 2012-01-01 false Location of nutrition information. 317... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.302 Location of nutrition information. (a) Nutrition information on a label of a packaged meat or meat food...

9 CFR 317.302 - Location of nutrition information.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Location of nutrition information. 317... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.302 Location of nutrition information. (a) Nutrition information on a label of a packaged meat or meat food...

46 CFR 160.077-31 - PFD Marking.

Code of Federal Regulations, 2010 CFR

2010-10-01

... requirements (except for persons in enclosed spaces as explained in owner's manual). [For Type V only] When... be used here]. A Pamphlet and Owner's Manual must be provided with this PFD. WARNING—TO REDUCE THE... used here]. [For Type I devices intended for recreational use] A Pamphlet and Owner's Manual must be...

46 CFR 160.047-6 - Marking.

Code of Federal Regulations, 2011 CFR

2011-10-01

... when wet. Do not snag or puncture inner plastic cover. If pads become waterlogged, replace device... buoyant vests shall be sufficiently waterproof so that after 72 hours submergence in water, it will withstand vigorous rubbing by hand while wet without the printed matter becoming illegible. [CGD 72-163R, 38...

30 CFR 75.601 - Short circuit protection of trailing cables.

Code of Federal Regulations, 2012 CFR

2012-07-01

... to disconnect power from trailing cables shall be plainly marked and identified and such devices... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Short circuit protection of trailing cables. 75... MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trailing Cables § 75.601 Short...

30 CFR 75.601 - Short circuit protection of trailing cables.

Code of Federal Regulations, 2011 CFR

2011-07-01

... to disconnect power from trailing cables shall be plainly marked and identified and such devices... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Short circuit protection of trailing cables. 75... MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trailing Cables § 75.601 Short...

30 CFR 75.601 - Short circuit protection of trailing cables.

Code of Federal Regulations, 2014 CFR

2014-07-01

... to disconnect power from trailing cables shall be plainly marked and identified and such devices... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Short circuit protection of trailing cables. 75... MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trailing Cables § 75.601 Short...

30 CFR 75.601 - Short circuit protection of trailing cables.

Code of Federal Regulations, 2013 CFR

2013-07-01

... to disconnect power from trailing cables shall be plainly marked and identified and such devices... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Short circuit protection of trailing cables. 75... MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trailing Cables § 75.601 Short...

9 CFR 317.24 - Packaging materials.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Packaging materials. 317.24 Section... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS General § 317.24 Packaging materials... packaging materials must be safe for their intended use within the meaning of section 409 of the Federal...

29 CFR 1917.43 - Powered industrial trucks.

Code of Federal Regulations, 2012 CFR

2012-07-01

... safety. (5) Powered industrial trucks shall be marked with their rated capacities, which shall be visible.... (5) Powered industrial trucks shall be maintained in safe working order. Safety devices shall not be... 29 Labor 7 2012-07-01 2012-07-01 false Powered industrial trucks. 1917.43 Section 1917.43 Labor...

29 CFR 1917.43 - Powered industrial trucks.

Code of Federal Regulations, 2014 CFR

2014-07-01

... safety. (5) Powered industrial trucks shall be marked with their rated capacities, which shall be visible.... (5) Powered industrial trucks shall be maintained in safe working order. Safety devices shall not be... 29 Labor 7 2014-07-01 2014-07-01 false Powered industrial trucks. 1917.43 Section 1917.43 Labor...

Internet Addiction in Adolescents

ERIC Educational Resources Information Center

Rebisz, Slawomir; Sikora, Ilona

2016-01-01

The possibilities offered by the use of the Internet increasingly intensify the problem of Internet addiction, which has become more prevalent in the last decade, marked by the growing availability of mobile devices and new media and their exacerbation of the problem. Research on Internet addiction, initiated by Kimberly Young at the end of the…

Determining the Optimal Number of Core Needle Biopsy Passes for Molecular Diagnostics.

PubMed

Hoang, Nam S; Ge, Benjamin H; Pan, Lorraine Y; Ozawa, Michael G; Kong, Christina S; Louie, John D; Shah, Rajesh P

2018-03-01

The number of core biopsy passes required for adequate next-generation sequencing is impacted by needle cut, needle gauge, and the type of tissue involved. This study evaluates diagnostic adequacy of core needle lung biopsies based on number of passes and provides guidelines for other tissues based on simulated biopsies in ex vivo porcine organ tissues. The rate of diagnostic adequacy for pathology and molecular testing from lung biopsy procedures was measured for eight operators pre-implementation (September 2012-October 2013) and post-implementation (December 2013-April 2014) of a standard protocol using 20-gauge side-cut needles for ten core biopsy passes at a single academic hospital. Biopsy pass volume was then estimated in ex vivo porcine muscle, liver, and kidney using side-cut devices at 16, 18, and 20 gauge and end-cut devices at 16 and 18 gauge to estimate minimum number of passes required for adequate molecular testing. Molecular diagnostic adequacy increased from 69% (pre-implementation period) to 92% (post-implementation period) (p < 0.001) for lung biopsies. In porcine models, both 16-gauge end-cut and side-cut devices require one pass to reach the validated volume threshold to ensure 99% adequacy for molecular characterization, while 18- and 20-gauge devices require 2-5 passes depending on needle cut and tissue type. Use of 20-gauge side-cut core biopsy needles requires a significant number of passes to ensure diagnostic adequacy for molecular testing across all tissue types. To ensure diagnostic adequacy for molecular testing, 16- and 18-gauge needles require markedly fewer passes.

Multiple serial picture presentation with millisecond resolution using a three-way LC-shutter-tachistoscope

PubMed Central

Fischmeister, Florian Ph.S.; Leodolter, Ulrich; Windischberger, Christian; Kasess, Christian H.; Schöpf, Veronika; Moser, Ewald; Bauer, Herbert

2010-01-01

Throughout recent years there has been an increasing interest in studying unconscious visual processes. Such conditions of unawareness are typically achieved by either a sufficient reduction of the stimulus presentation time or visual masking. However, there are growing concerns about the reliability of the presentation devices used. As all these devices show great variability in presentation parameters, the processing of visual stimuli becomes dependent on the display-device, e.g. minimal changes in the physical stimulus properties may have an enormous impact on stimulus processing by the sensory system and on the actual experience of the stimulus. Here we present a custom-built three-way LC-shutter-tachistoscope which allows experimental setups with both, precise and reliable stimulus delivery, and millisecond resolution. This tachistoscope consists of three LCD-projectors equipped with zoom lenses to enable stimulus presentation via a built-in mirror-system onto a back projection screen from an adjacent room. Two high-speed liquid crystal shutters are mounted serially in front of each projector to control the stimulus duration. To verify the intended properties empirically, different sequences of presentation times were performed while changes in optical power were measured using a photoreceiver. The obtained results demonstrate that interfering variabilities in stimulus parameters and stimulus rendering are markedly reduced. Together with the possibility to collect external signals and to send trigger-signals to other devices, this tachistoscope represents a highly flexible and easy to set up research tool not only for the study of unconscious processing in the brain but for vision research in general. PMID:20122963

Dynamic Corneal Surface Mapping with Electronic Speckle Pattern Interferometry

NASA Astrophysics Data System (ADS)

Iqbal, S.; Gualini, M. M. S.

2013-06-01

In view of the fast advancement in ophthalmic technology and corneal surgery, there is a strong need for the comprehensive mapping and characterization techniques for corneal surface. Optical methods with precision non-contact approaches have been found to be very useful for such bio measurements. Along with the normal mapping approaches, elasticity of corneal surface has an important role in its characterization and needs to be appropriately measured or estimated for broader diagnostics and better prospective surgical results, as it has important role in the post-op corneal surface reconstruction process. Use of normal corneal topographic devices is insufficient for any intricate analysis since these devices operate at relatively moderate resolution. In the given experiment, Pulsed Electronic Speckle Pattern Interferometry has been utilized along with an excitation mechanism to measure the dynamic response of the sample cornea. A Pulsed ESPI device has been chosen for the study because of its micron-level resolution and other advantages in real-time deformation analysis. A bovine cornea has been used as a sample in the subject experiment. The dynamic response has been taken on a chart recorder and it is observed that it does show a marked deformation at a specific excitation frequency, which may be taken as a characteristic elasticity parameter for the surface of that corneal sample. It was seen that outside resonance conditions the bovine cornea was not that much deformed. Through this study, the resonance frequency and the corresponding corneal deformations are mapped and plotted in real time. In these experiments, data was acquired and processed by FRAMES plus computer analysis system. With some analysis of the results, this technique can help us to refine a more detailed corneal surface mathematical model and some preliminary work was done on this. Such modelling enhancements may be useful for finer ablative surgery planning. After further experimentation, this technique can possibly be developed for in-vivo experiments on animals and humans and then may prospectively be matured for future clinical usage.

Modeling of Women's 100-m Dash World Record: Wind-Aided or Not?

NASA Astrophysics Data System (ADS)

Hazelrigg, Conner; Waibel, Bryson; Baker, Blane

2015-11-01

On July 16, 1988, Florence Griffith Joyner (FGJ) shattered the women's 100-m dash world record (WR) with a time of 10.49 s, breaking the previous mark by an astonishing 0.27 s. By all accounts FGJ dominated the race that day, securing her place as the premiere female sprinter of that era, and possibly all time. In the aftermath of such an extraordinary performance, track officials immediately assumed that her posted time was wind aided—that is, attained under tailwind conditions beyond the legal limit of 2.0 m/s for world records. However, wind-measuring devices at the track site showed zero wind conditions during her WR performance. Before and during FGJ's race, other wind-measuring devices indicated speeds exceeding 4.0 m/s at the site of the triple jump runway, located on the same field as the running track. Video clips of flags placed near the starting line of FGJ's race also revealed tailwind conditions. Using available data from that era, the study here incorporates modeling techniques to compute velocity and position as functions of time for no wind and tailwind conditions. Modeling under no wind conditions produces a 100-m time of 10.70 s, a performance clearly attainable by FGJ during this stage of her sprinting career. Incorporating tailwinds of 4.0 m/s into the computations reduces this time by approximately 0.20 s, in close agreement with FGJ's record-breaking performance. These results strongly suggest that tailwinds of order 4 m/s were present during FGJ's world record race even though wind-measuring devices at the track site did not register these speeds. In spite of such strong evidence to support a wind-aided race on July 16, 1988, FGJ remains one of the top female sprinters in history and would likely hold the WR even today, given that she attained a non-wind-aided 100-m time of 10.61 s on the day following her WR performance.

Robust analysis method for acoustic properties of biological specimens measured by acoustic microscopy

NASA Astrophysics Data System (ADS)

Arakawa, Mototaka; Mori, Shohei; Kanai, Hiroshi; Nagaoka, Ryo; Horie, Miki; Kobayashi, Kazuto; Saijo, Yoshifumi

2018-07-01

We proposed a robust analysis method for the acoustic properties of biological specimens measured by acoustic microscopy. Reflected pulse signals from the substrate and specimen were converted into frequency domains to obtain sound speed and thickness. To obtain the average acoustic properties of the specimen, parabolic approximation was performed to determine the frequency at which the amplitude of the normalized spectrum became maximum or minimum, considering the sound speed and thickness of the specimens and the operating frequency of the ultrasonic device used. The proposed method was demonstrated for a specimen of malignant melanoma of the skin by using acoustic microscopy attaching a concave transducer with a center frequency of 80 MHz. The variations in sound speed and thickness analyzed by the proposed method were markedly smaller than those analyzed by the method based on an autoregressive model. The proposed method is useful for the analysis of the acoustic properties of bilogical tissues or cells.

Flexible ferroelectric element based on van der Waals heteroepitaxy.

PubMed

Jiang, Jie; Bitla, Yugandhar; Huang, Chun-Wei; Do, Thi Hien; Liu, Heng-Jui; Hsieh, Ying-Hui; Ma, Chun-Hao; Jang, Chi-Yuan; Lai, Yu-Hong; Chiu, Po-Wen; Wu, Wen-Wei; Chen, Yi-Chun; Zhou, Yi-Chun; Chu, Ying-Hao

2017-06-01

We present a promising technology for nonvolatile flexible electronic devices: A direct fabrication of epitaxial lead zirconium titanate (PZT) on flexible mica substrate via van der Waals epitaxy. These single-crystalline flexible ferroelectric PZT films not only retain their performance, reliability, and thermal stability comparable to those on rigid counterparts in tests of nonvolatile memory elements but also exhibit remarkable mechanical properties with robust operation in bent states (bending radii down to 2.5 mm) and cycling tests (1000 times). This study marks the technological advancement toward realizing much-awaited flexible yet single-crystalline nonvolatile electronic devices for the design and development of flexible, lightweight, and next-generation smart devices with potential applications in electronics, robotics, automotive, health care, industrial, and military systems.

Flexible ferroelectric element based on van der Waals heteroepitaxy

PubMed Central

Jiang, Jie; Bitla, Yugandhar; Huang, Chun-Wei; Do, Thi Hien; Liu, Heng-Jui; Hsieh, Ying-Hui; Ma, Chun-Hao; Jang, Chi-Yuan; Lai, Yu-Hong; Chiu, Po-Wen; Wu, Wen-Wei; Chen, Yi-Chun; Zhou, Yi-Chun; Chu, Ying-Hao

2017-01-01

We present a promising technology for nonvolatile flexible electronic devices: A direct fabrication of epitaxial lead zirconium titanate (PZT) on flexible mica substrate via van der Waals epitaxy. These single-crystalline flexible ferroelectric PZT films not only retain their performance, reliability, and thermal stability comparable to those on rigid counterparts in tests of nonvolatile memory elements but also exhibit remarkable mechanical properties with robust operation in bent states (bending radii down to 2.5 mm) and cycling tests (1000 times). This study marks the technological advancement toward realizing much-awaited flexible yet single-crystalline nonvolatile electronic devices for the design and development of flexible, lightweight, and next-generation smart devices with potential applications in electronics, robotics, automotive, health care, industrial, and military systems. PMID:28630922

Serviceable pavement marking retroreflectivity levels : technical report.

DOT National Transportation Integrated Search

2009-03-01

This research addressed an array of issues related to measuring pavement markings retroreflectivity, factors : related to pavement marking performance, subjective evaluation process, best practices for using mobile : retroreflectometers, sampling pav...

Marking Student Programs Using Graph Similarity

ERIC Educational Resources Information Center

Naude, Kevin A.; Greyling, Jean H.; Vogts, Dieter

2010-01-01

We present a novel approach to the automated marking of student programming assignments. Our technique quantifies the structural similarity between unmarked student submissions and marked solutions, and is the basis by which we assign marks. This is accomplished through an efficient novel graph similarity measure ("AssignSim"). Our experiments…

75 FR 34946 - Federal Motor Vehicle Theft Prevention Standard; Final Listing of 2011 Light Duty Truck Lines...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-21

...This final rule announces NHTSA's determination that there are no new model year (MY) 2011 light duty truck lines subject to the parts-marking requirements of the Federal motor vehicle theft prevention standard because they have been determined by the agency to be high-theft or because they have a majority of interchangeable parts with those of a passenger motor vehicle line. This final rule also identifies those vehicle lines that have been granted an exemption from the parts-marking requirements because the vehicles are equipped with antitheft devices determined to meet certain statutory criteria.

76 FR 20251 - Federal Motor Vehicle Theft Prevention Standard; Final Listing of 2012 Light Duty Truck Lines...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-12

...This final rule announces NHTSA's determination that there are no new model year (MY) 2012 light duty truck lines subject to the parts-marking requirements of the Federal motor vehicle theft prevention standard because they have been determined by the agency to be high-theft or because they have a majority of interchangeable parts with those of a passenger motor vehicle line. This final rule also identifies those vehicle lines that have been granted an exemption from the parts-marking requirements because the vehicles are equipped with antitheft devices determined to meet certain statutory criteria.

78 FR 44030 - Federal Motor Vehicle Theft Prevention Standard; Final Listing of 2014 Light Duty Truck Lines...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-23

...This final rule announces NHTSA's determination that there are no new model year (MY) 2014 light duty truck lines subject to the parts-marking requirements of the Federal motor vehicle theft prevention standard because they have been determined by the agency to be high-theft or because they have a majority of interchangeable parts with those of a passenger motor vehicle line. This final rule also identifies those vehicle lines that have been granted an exemption from the parts-marking requirements because the vehicles are equipped with antitheft devices determined to meet certain statutory criteria.

Visual task performance in the blind with the BrainPort V100 Vision Aid.

PubMed

Stronks, H Christiaan; Mitchell, Ellen B; Nau, Amy C; Barnes, Nick

2016-10-01

The BrainPort® V100 Vision Aid is a non-invasive assistive device for the blind based on sensory substitution. The device translates camera images into electrotactile stimuli delivered to the tongue. The BrainPort has recently received the CE mark and FDA approval and it is currently marketed to augment, rather than replace, the traditional assistive technologies such as the white cane or guide dog. Areas covered: In this work, we will review the functional studies performed to date with the BrainPort and we will highlight the critical factors that determine device performance, including the technology behind the BrainPort, the impediments to assessing device performance, and the impact of device training and rehabilitation. Expert commentary: The BrainPort enables blind people to perceive light, identify simple objects, recognize short words, localize simple objects, and detect motion and orientation of objects. To achieve this, proper rehabilitation and training regimes are crucial.

Laser marking on microcrystalline silicon film.

PubMed

Park, Min Gyu; Choi, Se-Bum; Ruh, Hyun; Hwang, Hae-Sook; Yu, Hyunung

2012-07-01

We present a compact dot marker using a CW laser on a microcrystalline silicon (Si) thin film. A laser annealing shows a continuous crystallization transformation from nano to a large domain (> 200 nm) of Si nanocrystals. This microscale patterning is quite useful since we can manipulate a two-dimentional (2-D) process of Si structural forms for better and efficient thin-film transistor (TFT) devices as well as for photovoltaic application with uniform electron mobility. A Raman scattering microscope is adopted to draw a 2-D mapping of crystal Si film with the intensity of optical-phonon mode at 520 cm(-1). At a 300-nm spatial resolution, the position resolved the Raman scattering spectra measurements carried out to observe distribution of various Si species (e.g., large crystalline, polycrystalline and amorphous phase). The population of polycrystalline (poly-Si) species in the thin film can be analyzed with the frequency shift (delta omega) from the optical-phonon line since poly-Si distribution varies widely with conditions, such as an irradiated-laser power. Solid-phase crystallization with CW laser irradiation improves conductivity of poly-Si with micropatterning to develop the potential of the device application.

Reduction of the "burst release" of copper ions from copper-based intrauterine devices by organic inhibitors.

PubMed

Alvarez, Florencia; Schilardi, Patricia L; de Mele, Monica Fernández Lorenzo

2012-01-01

The copper intrauterine device is a contraceptive method that is based on the release of copper ions from a copper wire. Immediately after insertion, the dissolution of copper in the uterine fluid is markedly higher ("burst release") than that necessary for contraception action, leading to a variety of harmful effects. Pretreatments with organic compounds [thiourea (TU) and purine (PU), 10(-4)-10(-2) M concentration range, 1- and 3-h immersion times] were tested. The dissolution of copper with and without pretreatments in TU and PU solutions was analyzed by conventional electrochemical techniques and surface analysis. Pretreatments in PU solutions reduced the initial corrosion rate of copper in simulated uterine solutions, with inhibitory efficiencies that depend on the PU concentration and on the immersion time assayed. Inhibitory efficiency values higher than 98% for pretreatments with ≥10(-3) M PU were found. Conversely, after TU pretreatments, a high copper release was measured. It was concluded that 10(-3) M PU pretreatment is a promising strategy able to reduce the "burst release" of copper and to ensure contraceptive action. Copyright © 2012 Elsevier Inc. All rights reserved.

Aerometrics' laser-based lane-tracker sensor: engineering and on-the-road evaluation of advanced prototypes

NASA Astrophysics Data System (ADS)

Schuler, Carlos A.; Tapos, Francis M.; Alayleh, Mehyeddine M.; Bachalo, William D.

1997-02-01

Aerometrics initiated and continues on the development an innovative laser-diode based device that provides a warning signal when a motor-vehicle deviates from the center of the lane. The device is based on a sensor that scans the roadway on either side of the vehicle and determines the lateral position relative to the existing painted lines marking the lane. The principles of operation of the sensor, and the results of Aerometrics' early testing were presented last year in this forum. This paper presents Aerometrics' continuing efforts in bringing the technology to market. New prototypes have been developed and tested. Aerometrics' engineering efforts and the use of latest technologies have resulted in a 24-fold reduction in sensor volume when compared to their predecessors and similar reductions in weight. The current prototype measures less than 9 cm X 8 cm X 7 cm, and can be easily fit within the cavity of rear-view mirror holders used in most present-day vehicles. Also, advances in signal conditioning and processing have improved the reliability of the sensor. Results of continuing testing of the sensor will be presented.

Spin-filtering and giant magnetoresistance effects in polyacetylene-based molecular devices

NASA Astrophysics Data System (ADS)

Chen, Tong; Yan, Shenlang; Xu, Liang; Liu, Desheng; Li, Quan; Wang, Lingling; Long, Mengqiu

2017-07-01

Using the non-equilibrium Green's function formalism in combination with density functional theory, we performed ab initio calculations of spin-dependent electron transport in molecular devices consisting of a polyacetylene (CnHn+1) chain vertically attached to a carbon chain sandwiched between two semi-infinite zigzag-edged graphene nanoribbon electrodes. Spin-charge transport in the device could be modulated to different magnetic configurations by an external magnetic field. The results showed that single spin conduction could be obtained. Specifically, the proposed CnHn+1 devices exhibited several interesting effects, including (dual) spin filtering, spin negative differential resistance, odd-even oscillation, and magnetoresistance (MR). Marked spin polarization with a filtering efficiency of up to 100% over a large bias range was found, and the highest MR ratio for the CnHn+1 junctions reached 4.6 × 104. In addition, the physical mechanisms for these phenomena were also revealed.

Resistance training using eccentric overload induces early adaptations in skeletal muscle size.

PubMed

Norrbrand, Lena; Fluckey, James D; Pozzo, Marco; Tesch, Per A

2008-02-01

Fifteen healthy men performed a 5-week training program comprising four sets of seven unilateral, coupled concentric-eccentric knee extensions 2-3 times weekly. While eight men were assigned to training using a weight stack (WS) machine, seven men trained using a flywheel (FW) device, which inherently provides variable resistance and allows for eccentric overload. The design of these apparatuses ensured similar knee extensor muscle use and range of motion. Before and after training, maximal isometric force (MVC) was measured in tasks non-specific to the training modes. Volume of all individual quadriceps muscles was determined by magnetic resonance imaging. Performance across the 12 exercise sessions was measured using the inherent features of the devices. Whereas MVC increased (P < 0.05) at all angles measured in FW, such a change was less consistent in WS. There was a marked increase (P < 0.05) in task-specific performance (i.e., load lifted) in WS. Average work showed a non-significant 8.7% increase in FW. Quadriceps muscle volume increased (P < 0.025) in both groups after training. Although the more than twofold greater hypertrophy evident in FW (6.2%) was not statistically greater than that shown in WS (3.0%), all four individual quadriceps muscles of FW showed increased (P < 0.025) volume whereas in WS only m. rectus femoris was increased (P < 0.025). Collectively the results of this study suggest more robust muscular adaptations following flywheel than weight stack resistance exercise supporting the idea that eccentric overload offers a potent stimuli essential to optimize the benefits of resistance exercise.

Use of LS-DYNA(Registered TradeMark) to Assess the Energy Absorption Performance of a Shell-Based Kevlar(TradeMark)/Epoxy Composite Honeycomb

NASA Technical Reports Server (NTRS)

Polanco, Michael

2010-01-01

The forward and vertical impact stability of a composite honeycomb Deployable Energy Absorber (DEA) was evaluated during a full-scale crash test of an MD-500 helicopter at NASA Langley?s Landing and Impact Research Facility. The lower skin of the helicopter was retrofitted with DEA components to protect the airframe subfloor upon impact and to mitigate loads transmitted to Anthropomorphic Test Device (ATD) occupants. To facilitate the design of the DEA for this test, an analytical study was conducted using LS-DYNA(Registered TradeMark) to evaluate the performance of a shell-based DEA incorporating different angular cell orientations as well as simultaneous vertical and forward impact conditions. By conducting this study, guidance was provided in obtaining an optimum design for the DEA that would dissipate the kinetic energy of the airframe while maintaining forward and vertical impact stability.

Quantitative ENT endoscopy: the future in the new millennium

NASA Astrophysics Data System (ADS)

Mueller, Andreas; Schubert, Mario

1999-06-01

In Otorhinolaryngology the endoscopic appraisal of luminal dimensions of the nose, the throat, the larynx and the trachea is a daily problem. Those concerned with endoscopy know, that endoscopes distort dimensions of examined anatomical structures. To draw conclusions on luminal dimensions from the endoscopic pictures additional measuring devices are required. We developed a new method of measuring luminal dimensions in rigid or flexible endoscopy. For this a laser beam directed radially marks the anatomical lumen of interest in the videoendoscopic vision. The laser ring becomes deformed according to the form of the cavity explored. By keeping the distance defined between the laser ring and the top of the endoscope, the endoscopic video image can be measured. A piece of software developed by us calculates from the pictures the cross sectional area as well as the extension of benign or malign stenosis of the cavity explored. The result of the endoscopic measuring procedure can be visualized 3D on a PC-monitor. We are going to demonstrate the result of our clinical experience in different otorhinolaryngological diseases with the new endoscopic measuring kit in comparison to standard endoscopy. A further perspective is the endoscopic measuring kit in comparison to standard endoscopy. A further perspective is the endoscopic assisted manufacturing (EAM) of anatomical adapted stents, tubes and cannules.

Effects of device size and material on the bending performance of resistive-switching memory devices fabricated on flexible substrates

NASA Astrophysics Data System (ADS)

Lee, Won-Ho; Yoon, Sung-Min

2017-05-01

The resistive change memory (RCM) devices using amorphous In-Ga-Zn-O (IGZO) and microcrystalline Al-doped ZnO (AZO) thin films were fabricated on plastic substrates and characterized for flexible electronic applications. The device cell sizes were varied to 25 × 25, 50 × 50, 100 × 100, and 200 × 200 μm2 to examine the effects of cell size on the resistive-switching (RS) behaviors at a flat state and under bending conditions. First, it was found that the high-resistance state programmed currents markedly increased with the increase in the cell size. Second, while the AZO RCM devices did not exhibit RESET operations at a curvature radius smaller than 8.0 mm, the IGZO RCM devices showed sound RS behaviors even at a curvature radius of 4.5 mm. Third, for the IGZO RCM devices with the cell size bigger than 100 × 100 μm2, the RESET operation could not be performed at a curvature radius smaller than 6.5 mm. Thus, it was elucidated that the RS characteristics of the flexible RCM devices using oxide semiconductor thin films were closely related to the types of RS materials and the cell size of the device.

Certain aspects on medical devices software law regulation.

PubMed

Pashkov, Vitalii; Harkusha, Andrii

some kind of easiness of entry in creating software products on various computing platforms has led to such products being made available perhaps without due consideration of potential risks to users and patients and the most valuable reason for this have been lack of regulatory clarity. Some key points on legal regulation of abovementioned sphere is a base of this study. Ukrainian legislation, European Union`s Guidelines on the qualification and classification of standalone software; Guidance for the Content of Premarket Submissions for Software Contained in Medical Devices that works in United States of America. Article is based on dialectical, comparative, analytic, synthetic and comprehensive research methods. in accordance with Ukrainian legislation, software that has a medical purpose could be a medical device. Ukrainian legislation which is established on European Union Medical Devices Directives divide all medical devices on classes. But there aren't any special recommendations or advices on classifications for software medical devices in Ukraine. It is necessary to develop and adopt guidelines on the qualification and classification of medical device software in Ukraine especially considering the harmonization of Ukrainian legislation with the EU legislation, develop special rules for the application of the national mark of conformity for medical device software and defined the « responsible organization » for the medical device software approval process.

Florida's wet weather demonstration project : final report, January 2009.

DOT National Transportation Integrated Search

2008-11-01

The Florida Department of Transportation (FDOT) established a wet-weather pavement marking demonstration project with goals to gather performance data, evaluate various wet-weather marking systems, and develop a measurement protocol for measuring ret...

9 CFR 592.5 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Designation of official certificates... Section 592.5 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE... class, quality, quantity, or condition specified in this part or any symbol, stamp, label, or seal...

9 CFR 592.5 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Designation of official certificates... Section 592.5 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE... class, quality, quantity, or condition specified in this part or any symbol, stamp, label, or seal...

9 CFR 317.300 - Nutrition labeling of meat or meat food products.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Nutrition labeling of meat or meat... AND VOLUNTARY INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.300 Nutrition labeling of meat or meat food products. Link to an amendment published at 75...

9 CFR 317.300 - Nutrition labeling of meat or meat food products.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 9 Animals and Animal Products 2 2012-01-01 2012-01-01 false Nutrition labeling of meat or meat... AND VOLUNTARY INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.300 Nutrition labeling of meat or meat food products. Link to an amendment published at 75...

STS-116 payload egress training

NASA Image and Video Library

2005-08-01

JSC2005-E-32739 (1 Aug. 2005) --- Astronaut Mark L. Polansky, STS-116 commander, uses a special pulley device to lower himself from a simulated trouble-plagued shuttle during a training session in the Space Vehicle Mockup Facility at the Johnson Space Center. Polansky is wearing a training version of the shuttle launch and entry suit.

49 CFR 221.13 - Marking device display.

Code of Federal Regulations, 2014 CFR

2014-10-01

... by this subpart shall be illuminated continuously or flash during the period between one hour before sunset and one hour after sunrise, and during all other hours when weather conditions so restrict visibility that the end silhouette of a standard box car cannot be seen from 1/2 mile on tangent track by a...

21 CFR 886.4570 - Ophthalmic surgical marker.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Ophthalmic surgical marker. 886.4570 Section 886.4570 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED...) Identification. An ophthalmic surgical marker is a device intended to mark by use of ink, dye, or indentation the...

21 CFR 886.4570 - Ophthalmic surgical marker.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ophthalmic surgical marker. 886.4570 Section 886.4570 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED...) Identification. An ophthalmic surgical marker is a device intended to mark by use of ink, dye, or indentation the...

21 CFR 886.4570 - Ophthalmic surgical marker.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Ophthalmic surgical marker. 886.4570 Section 886.4570 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED...) Identification. An ophthalmic surgical marker is a device intended to mark by use of ink, dye, or indentation the...

21 CFR 886.4570 - Ophthalmic surgical marker.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Ophthalmic surgical marker. 886.4570 Section 886.4570 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED...) Identification. An ophthalmic surgical marker is a device intended to mark by use of ink, dye, or indentation the...

21 CFR 886.4570 - Ophthalmic surgical marker.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Ophthalmic surgical marker. 886.4570 Section 886.4570 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED...) Identification. An ophthalmic surgical marker is a device intended to mark by use of ink, dye, or indentation the...

PDAs: Revolutionizing the Way We Learn and Teach

ERIC Educational Resources Information Center

McDonough, Kimberly; Berge, Zane L.

2006-01-01

Miniature handheld computers called PDAs are not only bombarding corporate America, but they are also noticeably making their mark on college campuses. The question is, how much impact are they making on the way students learn and instructors teach. These devices were born from a simple calculator and over two decades have transformed into a…

Overhead Projection Cell for Streamline Flow

ERIC Educational Resources Information Center

Waage, Harold M.

1969-01-01

Describes the construction and operation of an overhead projection apparatus designed to demonstrate streamline flow of a liquid. The apparatus consists of a Plexiglass tank containing water in which plates forming the cell are submerged, a constant level reservoir, an overflow device and a system for marking the flow lines with a dye. (LC)

14 CFR 25.677 - Trim systems.

Code of Federal Regulations, 2013 CFR

2013-01-01

... clearly visible means to indicate the position of the trim device with respect to the range of adjustment. The indicator must be clearly marked with the range within which it has been demonstrated that takeoff... appropriately balanced and shown to be free from flutter. (d) If an irreversible tab control system is used, the...

78 FR 48367 - TRICARE Program; Clarification of Benefit Coverage of Durable Equipment and Ordering or...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-08

... allow certain other authorized individual professional providers acting within the scope of their... Management Activity (TMA) can reimburse for the base or basic equipment or device that meet the beneficiary's... Docket Management System Office, 4800 Mark Center Drive, 2nd floor, East Tower, Suite 02G09, Alexandria...

49 CFR 221.7 - Civil penalty.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Civil penalty. 221.7 Section 221.7 Transportation... TRANSPORTATION REAR END MARKING DEVICE-PASSENGER, COMMUTER AND FREIGHT TRAINS General § 221.7 Civil penalty. Any... requirement is subject to a civil penalty of at least $650 and not more than $25,000 per violation, except...

49 CFR 221.7 - Civil penalty.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Civil penalty. 221.7 Section 221.7 Transportation... TRANSPORTATION REAR END MARKING DEVICE-PASSENGER, COMMUTER AND FREIGHT TRAINS General § 221.7 Civil penalty. Any... requirement is subject to a civil penalty of at least $650 and not more than $25,000 per violation, except...

49 CFR 221.7 - Civil penalty.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Civil penalty. 221.7 Section 221.7 Transportation... TRANSPORTATION REAR END MARKING DEVICE-PASSENGER, COMMUTER AND FREIGHT TRAINS General § 221.7 Civil penalty. Any... requirement is subject to a civil penalty of at least $650 and not more than $25,000 per violation, except...

49 CFR 221.7 - Civil penalty.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Civil penalty. 221.7 Section 221.7 Transportation... TRANSPORTATION REAR END MARKING DEVICE-PASSENGER, COMMUTER AND FREIGHT TRAINS General § 221.7 Civil penalty. Any... requirement is subject to a civil penalty of at least $650 and not more than $25,000 per violation, except...

49 CFR 221.7 - Civil penalty.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Civil penalty. 221.7 Section 221.7 Transportation... TRANSPORTATION REAR END MARKING DEVICE-PASSENGER, COMMUTER AND FREIGHT TRAINS General § 221.7 Civil penalty. Any... requirement is subject to a civil penalty of at least $650 and not more than $25,000 per violation, except...

29 CFR 1926.1501 - Cranes and derricks.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., chains, or other reciprocating, rotating, or other moving parts or equipment shall be guarded if such... more than one hoisting unit, each hoist shall have its rated load marked on it or its load block, and... contact between the load block or overhaul ball and the boom tip (anti-two-blocking device), or a system...

The use of the durometer to measure rock hardness in geomorphology. Advantages and limitations.

NASA Astrophysics Data System (ADS)

Feal-Pérez, Alejandra; Blanco-Chao, Ramón; Valcarcel-Díaz, Marcos; Combes, Martín. A.

2010-05-01

The durometer is a hardness tester developed to measure hardness of metallic materials that has been recently introduced to measure rock hardness in weathering studies. Aoki & Matsukura (2007) highlight some advantages of the durometer compared with the Schmidt Rock Test Hammer: the smaller plunge allows measurements in small surfaces such as taffoni or rock carvings, the wider measurement range and the lower impact energy. This last makes it a non destructive method that can be used on relatively soft rocks. In this work the durometer Equotip (©) has been tested in different environments in the field and in the laboratory to explore its applicability and limitations. We applied the device on small rock samples of granite and limestone and a T-test showed that smaller sample size gave smaller hardness values (p < 0.01). Testing the effects of water content, there were no statistically significant differences between water saturated and dry samples. The influence of rock surface roughness was evaluated applying the durometer in ancient rock carvings in medium to coarse grain granites. We compared the values obtained inside and outside the grooves of the carvings using two different support rings, one flat and one concave. The flat ring was not able to reach the bottom of the groove, meanwhile the concave ring adjusts fairly well given its semi spherical section. A t-test confirmed the difference (p < 0.01) between lower rebound values obtained in the grooves using the flat ring and the higher and less scattered values obtained when the concave ring is used. As a very sensitive device, there are some problems in the use related with rock roughness and rock grain size. In weathered medium to coarse grained rocks, with very irregular surfaces, is not easy to get a good contact between the plunge and the rock surface. A poor contact caused by surface roughness causes the scattering and lowering of rebound values. On the contrary, in homogeneous fine grained rocks and in uniform rock surfaces the device gave very good results. The data obtained in glacial, nival and rock coastal environments showed the potential of the device in the identification of changes in rock hardness. We were able to asses the changes in the weathering degree of glacial striations and marked differences in the rock surfaces subjected or not to abrasion. A. Feal-Pérez is supported by the grant AP2006-03854 (Spanish Ministry of Education)

Electrochemical Micromachining with Fiber Laser Masking for 304 Stainless Steel

NASA Astrophysics Data System (ADS)

Li, Xiaohai; Wang, Shuming; Wang, Dong; Tong, Han

2017-10-01

In order to fabricate micro structure, the combined machining of electrochemical micro machining (EMM) and laser masking for 304 stainless steel was studied. A device of composite machining of EMM with laser masking was developed, and the experiments of EMM with laser masking were carried out. First, by marking pattern with fiber laser on the surface of 304 stainless steel, the special masking layer can be formed. Through X ray photoelectron spectroscopy (XPS), the corrosion resistance of laser masking layer was analyzed. It is proved by XPS that the iron oxide and chromium oxide on the surface of stainless steel generates due to air oxidation when laser scanning heats. Second, the localization and precision of EMM are improved, since the marking patterns forming on the surface of stainless steel by laser masking play a protective role in the process of subsequent EMM when the appropriate parameters of EMM are selected. At last, the shape and the roughness of the machined samples were measured by SEM and optical profilometer and analyzed. The results show that the rapid fabrication of micro structures on the 304 stainless steel surface can be achieved by EMM with fiber laser masking, which has a good prospect in the field of micro machining.

Flight Investigation to Improve the Dynamic Longitudinal Stability and Control-Feel Characteristics of the P-63A-1 Airplane (AAF No. 42-68889) with Closely Balanced Experimental Elevators

NASA Technical Reports Server (NTRS)

Johnson, Harold I.

1946-01-01

Results of flight tests of a control-feel aid presented. This device consisted of a spring and dashpot connected in series between the control stick and airplane structure. The device was tested in combination with an experimental elevator and bobweight which had given unsatisfactory dynamic stability and control-feel characteristics in previous tests. The control-feel aid effected marked improvement in both the control-feel characteristics and the control-feel dynamic longitudinal stability of the airplane.

Experimental analysis of dark frame growth mechanism in organic light-emitting diodes

NASA Astrophysics Data System (ADS)

Minagawa, Masahiro; Tanabe, Takuma; Kondo, Eiki; Kamimura, Kenji; Kimura, Munehiro

2018-02-01

Organic light-emitting diodes (OLEDs) were fabricated with heterojunction interfaces and layers that were prepared by cold isostatic pressing (CIP), and the growth characteristics of their non-emission areas, or dark frames (D/Fs), were investigated during storage. We fabricated an OLED with an indium-tin-oxide (ITO)/N,N‧-di(1-naphthyl)-N,N‧-diphenyl-(1,1‧-biphenyl)-4,4‧-diamine (α-NPD)/tris(8-hydroxylquinoline)aluminum (Alq3)/LiF/Al structure without CIP treatment (Device I), as well as OLEDs that were pressed after the deposition of α-NPD (Device II), Alq3 (Device III), and LiF/Al (Device IV) layers. Although Devices I, II, and III showed typical D/F growth characteristics, the D/F growth rate in Device IV was markedly mitigated, indicating that the Alq3/LiF/Al interfaces dominated the D/F growth. Moreover, we found that the electron injection characteristic was poorer in the electron-only device stored after the LiF layer deposition than in that stored before the LiF deposition. Therefore, the decreased electron injection due to storage at the interfaces was attributed to the D/F growth.

Wood Bond Testing

NASA Technical Reports Server (NTRS)

1989-01-01

A joint development program between Hartford Steam Boiler Inspection Technologies and The Weyerhaeuser Company resulted in an internal bond analyzer (IBA), a device which combines ultrasonics with acoustic emission testing techniques. It is actually a spinoff from a spinoff, stemming from a NASA Lewis invented acousto-ultrasonic technique that became a system for testing bond strength of composite materials. Hartford's parent company, Acoustic Emission Technology Corporation (AET) refined and commercialized the technology. The IBA builds on the original system and incorporates on-line process control systems. The IBA determines bond strength by measuring changes in pulsar ultrasonic waves injected into a board. Analysis of the wave determines the average internal bond strength for the panel. Results are displayed immediately. Using the system, a mill operator can adjust resin/wood proportion, reduce setup time and waste, produce internal bonds of a consistent quality and automatically mark deficient products.

Field emission and explosive electron emission process in focused ion beam fabricated platinum and tungsten three-dimensional overhanging nanostructure

NASA Astrophysics Data System (ADS)

Singh, Abhishek Kumar

2018-06-01

Three-dimensional platinum and tungsten overhanging nanogap (∼70 nm) electrodes are fabricated on a glass substrate using focused ion beam milling and chemical vapour deposition processes. Current-voltage (I-V) characteristics of the devices measured at a pressure of ∼10-6 mbar shows space-charge emission followed by the Fowler-Nordheim (F-N) field emission. After the F-N emission, the system enters into an explosive emission process, at a higher voltage generating a huge current. We observe a sharp and abrupt rise in the emission current which marks the transition from the F-N emission to the explosive emission state. The explosive emission process is destructive in nature and yields micro-/nano-size spherical metal particles. The chemical compositions and the size-distribution of such particles are performed.

Handheld single photon emission computed tomography (handheld SPECT) navigated video-assisted thoracoscopic surgery of computer tomography-guided radioactively marked pulmonary lesions.

PubMed

Müller, Joachim; Putora, Paul Martin; Schneider, Tino; Zeisel, Christoph; Brutsche, Martin; Baty, Florent; Markus, Alexander; Kick, Jochen

2016-09-01

Radioactive marking can be a valuable extension to minimally invasive surgery. The technique has been clinically applied in procedures involving sentinel lymph nodes, parathyroidectomy as well as interventions in thoracic surgery. Improvements in equipment and techniques allow one to improve the limits. Pulmonary nodules are frequently surgically removed for diagnostic or therapeutic reasons; here video-assisted thoracoscopic surgery (VATS) is the preferred technique. VATS might be impossible with nodules that are small or located deep in the lung. In this study, we examined the clinical application and safety of employing the newly developed handheld single photon emission tomography (handheld SPECT) device in combination with CT-guided radioactive marking of pulmonary nodules. In this pilot study, 10 subjects requiring surgical resection of a pulmonary nodule were included. The technique involved CT-guided marking of the target nodule with a 20-G needle, with subsequent injection of 25-30 MBq (effective: 7-14 MBq) Tc-99m MAA (Macro Albumin Aggregate). Quality control was made with conventional SPECT-CT to confirm the correct localization and exclude possible complications related to the puncture procedure. VATS was subsequently carried out using the handheld SPECT to localize the radioactivity intraoperatively and therefore the target nodule. A 3D virtual image was superimposed on the intraoperative visual image for surgical guidance. In 9 of the 10 subjects, the radioactive application was successfully placed directly in or in the immediate vicinity of the target nodule. The average size of the involved nodules was 9 mm (range 4-15). All successfully marked nodules were subsequently completely excised (R0) using VATS. The procedure was well tolerated. An asymptomatic clinically insignificant pneumothorax occurred in 5 subjects. Two subjects were found to have non-significant discrete haemorrhage in the infiltration canal of the needle. In a single subject, the radioactive marking was unsuccessful because the radioactivity spread into the pleural space. In our series of 10 patients, it was demonstrated that using handheld SPECT in conjunction with VATS to remove radioactively marked pulmonary nodules is feasible. The combination of proven surgical techniques with a novel localization device (handheld SPECT) allowed successful VATS excision of pulmonary nodules which, due to their localization and small size, would typically have required thoracotomy. ClinicalTrials.gov, NCT02050724, Public 01/29/214, Joachim Müller. © The Author 2016. Published by Oxford University Press on behalf of the European Association for Cardio-Thoracic Surgery. All rights reserved.

Early trends in N-terminal pro-brain natriuretic peptide values after left ventricular assist device implantation for chronic heart failure.

PubMed

Hasin, Tal; Kushwaha, Sudhir S; Lesnick, Timothy G; Kremers, Walter; Boilson, Barry A; Schirger, John A; Clavell, Alfredo L; Rodeheffer, Richard J; Frantz, Robert P; Edwards, Brooks S; Pereira, Naveen L; Stulak, John M; Joyce, Lyle; Daly, Richard; Park, Soon J; Jaffe, Allan S

2014-10-15

Left ventricular assist devices (LVADs) acutely decrease left ventricular wall stress. Thus, early postoperative levels of N-terminal pro-brain natriuretic peptide (NT-proBNP) should decrease. This study investigated postoperative changes in NT-proBNP levels, the parameters related to changes, and the possible association with complications by performing a retrospective analysis of changes in daily NT-proBNP (pg/ml) levels from admission to discharge both before and after LVAD implantation in a tertiary referral center. For 72 patients implanted with HeartMate II LVADs, baseline NT-proBNP levels were elevated at 3,943 ng/ml (interquartile range 1,956 to 12,964). Preoperative stabilization led to marked decreases in NT-proBNP. Levels peaked 3 days after surgery and subsequently decreased. Patients with complicated postoperative courses had higher early postoperative elevations. By discharge, NT-proBNP decreased markedly but was still 2.83 (1.60 to 5.76) times the age-based upper limit of normal. The 26% reduction in NT-proBNP between admission and discharge was due mostly to the preoperative reductions and not those induced by the LVAD itself. The decrease was not associated with decreases in LV volume. In conclusion, preoperative treatment reduces NT-proBNP values. The magnitude of early postoperative changes is related to the clinical course. Levels at discharge remain markedly elevated and similar to values after preoperative stabilization despite presumptive acute LV unloading. Copyright © 2014 Elsevier Inc. All rights reserved.

3D Printed Multimaterial Microfluidic Valve.

PubMed

Keating, Steven J; Gariboldi, Maria Isabella; Patrick, William G; Sharma, Sunanda; Kong, David S; Oxman, Neri

2016-01-01

We present a novel 3D printed multimaterial microfluidic proportional valve. The microfluidic valve is a fundamental primitive that enables the development of programmable, automated devices for controlling fluids in a precise manner. We discuss valve characterization results, as well as exploratory design variations in channel width, membrane thickness, and membrane stiffness. Compared to previous single material 3D printed valves that are stiff, these printed valves constrain fluidic deformation spatially, through combinations of stiff and flexible materials, to enable intricate geometries in an actuated, functionally graded device. Research presented marks a shift towards 3D printing multi-property programmable fluidic devices in a single step, in which integrated multimaterial valves can be used to control complex fluidic reactions for a variety of applications, including DNA assembly and analysis, continuous sampling and sensing, and soft robotics.

Unequal Probability Marking Approach to Enhance Security of Traceback Scheme in Tree-Based WSNs.

PubMed

Huang, Changqin; Ma, Ming; Liu, Xiao; Liu, Anfeng; Zuo, Zhengbang

2017-06-17

Fog (from core to edge) computing is a newly emerging computing platform, which utilizes a large number of network devices at the edge of a network to provide ubiquitous computing, thus having great development potential. However, the issue of security poses an important challenge for fog computing. In particular, the Internet of Things (IoT) that constitutes the fog computing platform is crucial for preserving the security of a huge number of wireless sensors, which are vulnerable to attack. In this paper, a new unequal probability marking approach is proposed to enhance the security performance of logging and migration traceback (LM) schemes in tree-based wireless sensor networks (WSNs). The main contribution of this paper is to overcome the deficiency of the LM scheme that has a higher network lifetime and large storage space. In the unequal probability marking logging and migration (UPLM) scheme of this paper, different marking probabilities are adopted for different nodes according to their distances to the sink. A large marking probability is assigned to nodes in remote areas (areas at a long distance from the sink), while a small marking probability is applied to nodes in nearby area (areas at a short distance from the sink). This reduces the consumption of storage and energy in addition to enhancing the security performance, lifetime, and storage capacity. Marking information will be migrated to nodes at a longer distance from the sink for increasing the amount of stored marking information, thus enhancing the security performance in the process of migration. The experimental simulation shows that for general tree-based WSNs, the UPLM scheme proposed in this paper can store 1.12-1.28 times the amount of stored marking information that the equal probability marking approach achieves, and has 1.15-1.26 times the storage utilization efficiency compared with other schemes.

Unequal Probability Marking Approach to Enhance Security of Traceback Scheme in Tree-Based WSNs

PubMed Central

Huang, Changqin; Ma, Ming; Liu, Xiao; Liu, Anfeng; Zuo, Zhengbang

2017-01-01

Fog (from core to edge) computing is a newly emerging computing platform, which utilizes a large number of network devices at the edge of a network to provide ubiquitous computing, thus having great development potential. However, the issue of security poses an important challenge for fog computing. In particular, the Internet of Things (IoT) that constitutes the fog computing platform is crucial for preserving the security of a huge number of wireless sensors, which are vulnerable to attack. In this paper, a new unequal probability marking approach is proposed to enhance the security performance of logging and migration traceback (LM) schemes in tree-based wireless sensor networks (WSNs). The main contribution of this paper is to overcome the deficiency of the LM scheme that has a higher network lifetime and large storage space. In the unequal probability marking logging and migration (UPLM) scheme of this paper, different marking probabilities are adopted for different nodes according to their distances to the sink. A large marking probability is assigned to nodes in remote areas (areas at a long distance from the sink), while a small marking probability is applied to nodes in nearby area (areas at a short distance from the sink). This reduces the consumption of storage and energy in addition to enhancing the security performance, lifetime, and storage capacity. Marking information will be migrated to nodes at a longer distance from the sink for increasing the amount of stored marking information, thus enhancing the security performance in the process of migration. The experimental simulation shows that for general tree-based WSNs, the UPLM scheme proposed in this paper can store 1.12–1.28 times the amount of stored marking information that the equal probability marking approach achieves, and has 1.15–1.26 times the storage utilization efficiency compared with other schemes. PMID:28629135

Abbreviations for device names: a proposed methodology with specific examples.

PubMed

Alam, Murad; Dover, Jeffrey S; Alam, Murad; Goldman, Mitchel P; Kaminer, Michael S; Orringer, Jeffrey; Waldorf, Heidi; Alam, Murad; Avram, Mathew; Cohen, Joel L; Draelos, Zoe Diana; Dover, Jeffrey S; Hruza, George; Kilmer, Suzanne; Lawrence, Naomi; Lupo, Mary; Metelitsa, Andrei; Nestor, Mark; Ross, E Victor

2013-04-01

Many devices used in dermatology lack generic names. If investigators use commercial device names, they risk the appearance of bias. Alternatively, reliance on ad-hoc names and abbreviations may confuse readers who do not recognize these. To develop a system for assigning abbreviations to denote devices commonly used in dermatology. Secondarily, to use this system to create abbreviations for FDA-approved neurotoxins and prepackaged injectable soft-tissue augmentation materials. The American Society for Dermatologic Surgery convened a Lexicon Task Force in March 2012. One charge of this Task Force was to develop criteria for assigning abbreviations to medical devices. A modified consensus process was used. Abbreviations to denote devices were to be: based on a standardized approach; transparent to the casual reader; markedly brief; and in all cases, different than the commercial names. Three-letter all caps abbreviations, some with subscripts, were assigned to denote each of the approved neurotoxins and fillers. A common system of abbreviations for medical devices in dermatology may avoid the appearance of bias while ensuring effective communication. The proposed system may be expanded to name other devices, and the ensuing abbreviations may be suitable for journal articles, continuing medical education lectures, or other academic or clinical purposes. © 2013 by the American Society for Dermatologic Surgery, Inc. Published by Wiley Periodicals, Inc.

Use of technology in children’s dietary assessment

PubMed Central

Boushey, CJ; Kerr, DA; Wright, J; Lutes, KD; Ebert, DS; Delp, EJ

2010-01-01

Background Information on dietary intake provides some of the most valuable insights for mounting intervention programmes for the prevention of chronic diseases. With the growing concern about adolescent overweight, the need to accurately measure diet becomes imperative. Assessment among adolescents is problematic as this group has irregular eating patterns and they have less enthusiasm for recording food intake. Subjects/Methods We used qualitative and quantitative techniques among adolescents to assess their preferences for dietary assessment methods. Results Dietary assessment methods using technology, for example, a personal digital assistant (PDA) or a disposable camera, were preferred over the pen and paper food record. Conclusions There was a strong preference for using methods that incorporate technology such as capturing images of food. This suggests that for adolescents, dietary methods that incorporate technology may improve cooperation and accuracy. Current computing technology includes higher resolution images, improved memory capacity and faster processors that allow small mobile devices to process information not previously possible. Our goal is to develop, implement and evaluate a mobile device (for example, PDA, mobile phone) food record that will translate to an accurate account of daily food and nutrient intake among adolescents. This mobile computing device will include digital images, a nutrient database and image analysis for identification and quantification of food consumption. Mobile computing devices provide a unique vehicle for collecting dietary information that reduces the burden on record keepers. Images of food can be marked with a variety of input methods that link the item for image processing and analysis to estimate the amount of food. Images before and after the foods are eaten can estimate the amount of food consumed. The initial stages and potential of this project will be described. PMID:19190645

Use of technology in children's dietary assessment.

PubMed

Boushey, C J; Kerr, D A; Wright, J; Lutes, K D; Ebert, D S; Delp, E J

2009-02-01

Information on dietary intake provides some of the most valuable insights for mounting intervention programmes for the prevention of chronic diseases. With the growing concern about adolescent overweight, the need to accurately measure diet becomes imperative. Assessment among adolescents is problematic as this group has irregular eating patterns and they have less enthusiasm for recording food intake. We used qualitative and quantitative techniques among adolescents to assess their preferences for dietary assessment methods. Dietary assessment methods using technology, for example, a personal digital assistant (PDA) or a disposable camera, were preferred over the pen and paper food record. There was a strong preference for using methods that incorporate technology such as capturing images of food. This suggests that for adolescents, dietary methods that incorporate technology may improve cooperation and accuracy. Current computing technology includes higher resolution images, improved memory capacity and faster processors that allow small mobile devices to process information not previously possible. Our goal is to develop, implement and evaluate a mobile device (for example, PDA, mobile phone) food record that will translate to an accurate account of daily food and nutrient intake among adolescents. This mobile computing device will include digital images, a nutrient database and image analysis for identification and quantification of food consumption. Mobile computing devices provide a unique vehicle for collecting dietary information that reduces the burden on record keepers. Images of food can be marked with a variety of input methods that link the item for image processing and analysis to estimate the amount of food. Images before and after the foods are eaten can estimate the amount of food consumed. The initial stages and potential of this project will be described.

Architecture, development and implementation of a SWIR to visible integrated up-conversion imaging device

NASA Astrophysics Data System (ADS)

Sarusi, Gabby; Templeman, Tzvi; Hechster, Elad; Nissim, Nimrod; Vitenberg, Vladimir; Maman, Nitzan; Tal, Amir; Solodar, Assi; Makov, Guy; Abdulhalim, Ibrahim; Visoly-Fisher, Iris; Golan, Yuval

2016-04-01

A new concept of short wavelength infrared (SWIR) to visible upconversion integrated imaging device is proposed, modeled and some initial measured results are presented. The device is a hybrid inorganic-organic device that comprises six nano-metric scale sub-layers grown on n-type GaAs substrates. The first layer is a ~300nm thick PbSe nano-columnar absorber layer grown in (111) orientation to the substrate plan (100), with a diameter of 8- 10nm and therefore exhibit quantum confinement effects parallel to the substrate and bulk properties perpendicular to it. The advantage of this structure is the high oscillator strength and hence absorption to incoming SWIR photons while maintaining the high bulk mobility of photo-excited charges along the columns. The top of the PbSe absorber layer is coated with 20nm thick metal layer that serves as a dual sided mirror, as well as a potentially surface plasmon enhanced absorption in the PbSe nano-columns layer. The photo-excited charges (holes and electrons in opposite directions) are drifted under an external applied field to the OLED section (that is composed of a hole transport layer, an emission layer and an electron transport layer) where they recombine with injected electron from the transparent cathode and emit visible light through this cathode. Due to the high absorption and enhanced transport properties this architecture has the potential of high quantum efficiency, low cost and easy implementation in any optical system. As a bench-mark, alternative concept where InGaAs/InP heterojunction couple to liquid crystal optical spatial light modulator (OSLM) structure was built that shows a full upconversion to visible of 1550nm laser light.

Electrical switching dynamics and broadband microwave characteristics of VO2 radio frequency devices

NASA Astrophysics Data System (ADS)

Ha, Sieu D.; Zhou, You; Fisher, Christopher J.; Ramanathan, Shriram; Treadway, Jacob P.

2013-05-01

Vanadium dioxide (VO2) is a correlated electron system that features a metal-insulator phase transition (MIT) above room temperature and is of interest in high speed switching devices. Here, we integrate VO2 into two-terminal coplanar waveguides and demonstrate a large resistance modulation of the same magnitude (>103) in both electrically (i.e., by bias voltage, referred to as E-MIT) and thermally (T-MIT) driven transitions. We examine transient switching characteristics of the E-MIT and observe two distinguishable time scales for switching. We find an abrupt jump in conductivity with a rise time of the order of 10 ns followed by an oscillatory damping to steady state on the order of several μs. We characterize the RF power response in the On state and find that high RF input power drives VO2 further into the metallic phase, indicating that electromagnetic radiation-switching of the phase transition may be possible. We measure S-parameter RF properties up to 13.5 GHz. Insertion loss is markedly flat at 2.95 dB across the frequency range in the On state, and sufficient isolation of over 25 dB is observed in the Off state. We are able to simulate the RF response accurately using both lumped element and 3D electromagnetic models. Extrapolation of our results suggests that optimizing device geometry can reduce insertion loss further and maintain broadband flatness up to 40 GHz.

Slowing DNA Translocation in a Nanofluidic Field-Effect Transistor.

PubMed

Liu, Yifan; Yobas, Levent

2016-04-26

Here, we present an experimental demonstration of slowing DNA translocation across a nanochannel by modulating the channel surface charge through an externally applied gate bias. The experiments were performed on a nanofluidic field-effect transistor, which is a monolithic integrated platform featuring a 50 nm-diameter in-plane alumina nanocapillary whose entire length is surrounded by a gate electrode. The field-effect transistor behavior was validated on the gating of ionic conductance and protein transport. The gating of DNA translocation was subsequently studied by measuring discrete current dips associated with single λ-DNA translocation events under a source-to-drain bias of 1 V. The translocation speeds under various gate bias conditions were extracted by fitting event histograms of the measured translocation time to the first passage time distributions obtained from a simple 1D biased diffusion model. A positive gate bias was observed to slow the translocation of single λ-DNA chains markedly; the translocation speed was reduced by an order of magnitude from 18.4 mm/s obtained under a floating gate down to 1.33 mm/s under a positive gate bias of 9 V. Therefore, a dynamic and flexible regulation of the DNA translocation speed, which is vital for single-molecule sequencing, can be achieved on this device by simply tuning the gate bias. The device is realized in a conventional semiconductor microfabrication process without the requirement of advanced lithography, and can be potentially further developed into a compact electronic single-molecule sequencer.

Front lighted optical tooling method and apparatus

DOEpatents

Stone, William J.

1985-06-18

An optical tooling method and apparatus uses a front lighted shadowgraphic technique to enhance visual contrast of reflected light. The apparatus includes an optical assembly including a fiducial mark, such as cross hairs, reflecting polarized light with a first polarization, a polarizing element backing the fiducial mark and a reflective surface backing the polarizing element for reflecting polarized light bypassing the fiducial mark and traveling through the polarizing element. The light reflected by the reflecting surface is directed through a second pass of the polarizing element toward the frontal direction with a polarization differing from the polarization of the light reflected by the fiducial mark. When used as a tooling target, the optical assembly may be mounted directly to a reference surface or may be secured in a mounting, such as a magnetic mounting. The optical assembly may also be mounted in a plane defining structure and used as a spherometer in conjunction with an optical depth measuring instrument. A method of measuring a radius of curvature of an unknown surface includes positioning the spherometer on a surface between the surface and a depth measuring optical instrument. As the spherometer is frontally illuminated, the distance from the depth measuring instrument to the fiducial mark and the underlying surface are alternately measured and the difference in these measurements is used as the sagittal height to calculate a radius of curvature.

78 FR 50489 - Petition for Exemption From the Vehicle Theft Prevention Standard; Volkswagen Group of America, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-19

...) petition for exemption of the Audi confidential vehicle line in accordance with 49 CFR part 543, Exemption... 2015 Audi vehicle line. The petition requested an exemption from parts- marking requirement pursuant to... the components of the antitheft device for its Audi vehicle line. Volkswagen will install its...

49 CFR Appendix A-I to Part 541 - Lines With Antitheft Devices Which Are Exempted From the Parts-Marking Requirements of This...

Code of Federal Regulations, 2010 CFR

2010-10-01

... Tribeca. Outback. Suzuki XL-7. Toyota Camry.1 Lexus ES. Lexus GS. Lexus LS. Lexus SC. Volkswagen Audi 5000S. Audi A3. Audi A4. Audi Allroad. Audi A6. Audi Q5. New Beetle. Golf/Rabbit/GTI/R32. Jetta. Passat...

The Grammar of Technique: Inside "Continuidad de los Parques" (Continuity of the Parks).

ERIC Educational Resources Information Center

Lunn, Patricia V.; Albrecht, Jane W.

1997-01-01

Discusses the manipulation of various grammatical devices in a Spanish short story. Points out that variations in the use of verbal aspect mark stages in the development of the plot and that modal and lexical choices reinforce its reflexive and repetitive nature. Argues that this story exemplifies creative use of grammatical choices. (13…

9 CFR 354.2 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Designation of official certificates... Section 354.2 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE... means any symbol, stamp, label, or seal indicating that the product has been officially inspected and/or...

9 CFR 354.2 - Designation of official certificates, memoranda, marks, other identifications, and devices for...

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Designation of official certificates... Section 354.2 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE... means any symbol, stamp, label, or seal indicating that the product has been officially inspected and/or...

Getting in Touch: Use of Mobile Devices in the Elementary Classroom

ERIC Educational Resources Information Center

Ciampa, Katia; Gallagher, Tiffany L.

2013-01-01

In this single-case study, we examined the perceived influence of school-wide Apple iPod Touch integration on student learning and engagement. Data collection consisted of elementary teacher and principal interviews, as well as parent surveys. Findings revealed that there was a marked shift in teachers' and students' perceived roles when the iPod…

9 CFR 317.345 - Nutrition labeling of single-ingredient, raw meat products that are not ground or chopped...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 9 Animals and Animal Products 2 2014-01-01 2014-01-01 false Nutrition labeling of single... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.345 Nutrition....301. (a)(1) Nutrition information on the major cuts of single-ingredient, raw meat products identified...

9 CFR 317.345 - Nutrition labeling of single-ingredient, raw meat products that are not ground or chopped...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 9 Animals and Animal Products 2 2013-01-01 2013-01-01 false Nutrition labeling of single... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS Nutrition Labeling § 317.345 Nutrition....301. (a)(1) Nutrition information on the major cuts of single-ingredient, raw meat products identified...

2013 Materials Research Society Fall Meeting

DTIC Science & Technology

2014-06-18

metamaterials. Highlights included reports on significant breakthroughs in metasurface design and implementation, as well as important advances in...Mark Brongersma, Device Applications of Metafilms and Metasurfaces Monday, 8:30AM—Room 209, Hynes Metafilms and Metasurfaces have much potential to...patterning the constituent layers at length scales well below the wavelength of light. The resulting metafilms and metasurfaces offer opportunities

Investigating the Key Attributes to Enhance Students' Learning Experience in 21st Century Class Environment

ERIC Educational Resources Information Center

Leow, Fui-Theng; Neo, Mai; Hew, Soon Hin

2016-01-01

The 21st century marks the beginning of digital age with the extensive use of digital media, mobile devices, and Internet resources. Recent studies found that this digital era has expanded the landscape of student experiences, and educational technologies as well as increased the educator's awareness on embracing technologies to promote effective…

49 CFR 178.337-9 - Pressure relief devices, piping, valves, hoses, and fittings.

Code of Federal Regulations, 2012 CFR

2012-10-01

... filling line that communicates with vapor may be marked “spray-fill” instead of “vapor.” (d) Refrigeration and heating coils. (1) Refrigeration and heating coils must be securely anchored with provisions for.../refrigeration system, whichever is higher. A cargo tank may not be placed in service if any leakage occurs or...

49 CFR 178.337-9 - Pressure relief devices, piping, valves, hoses, and fittings.

Code of Federal Regulations, 2014 CFR

2014-10-01

... filling line that communicates with vapor may be marked “spray-fill” instead of “vapor.” (d) Refrigeration and heating coils. (1) Refrigeration and heating coils must be securely anchored with provisions for.../refrigeration system, whichever is higher. A cargo tank may not be placed in service if any leakage occurs or...

49 CFR 178.337-9 - Pressure relief devices, piping, valves, hoses, and fittings.

Code of Federal Regulations, 2011 CFR

2011-10-01

... filling line that communicates with vapor may be marked “spray-fill” instead of “vapor.” (d) Refrigeration and heating coils. (1) Refrigeration and heating coils must be securely anchored with provisions for.../refrigeration system, whichever is higher. A cargo tank may not be placed in service if any leakage occurs or...

49 CFR 178.337-9 - Pressure relief devices, piping, valves, hoses, and fittings.

Code of Federal Regulations, 2010 CFR

2010-10-01

... filling line that communicates with vapor may be marked “spray-fill” instead of “vapor.” (d) Refrigeration and heating coils. (1) Refrigeration and heating coils must be securely anchored with provisions for.../refrigeration system, whichever is higher. A cargo tank may not be placed in service if any leakage occurs or...

49 CFR 178.337-9 - Pressure relief devices, piping, valves, hoses, and fittings.

Code of Federal Regulations, 2013 CFR

2013-10-01

... filling line that communicates with vapor may be marked “spray-fill” instead of “vapor.” (d) Refrigeration and heating coils. (1) Refrigeration and heating coils must be securely anchored with provisions for.../refrigeration system, whichever is higher. A cargo tank may not be placed in service if any leakage occurs or...

49 CFR 221.14 - Marking devices.

Code of Federal Regulations, 2010 CFR

2010-10-01

... side of the horizontal center line as defined in terms of the 50 candela intensity points; (3) A color defined by the red-orange-amber color range; and (4) If a flashing light is used, a flash rate of not less... classification light on the rear of the locomotive, provided it complies with paragraph (a) of this section; or...

49 CFR 393.24 - Requirements for head lamps, auxiliary driving lamps and front fog lamps.

Code of Federal Regulations, 2011 CFR

2011-10-01

... the driver's will and be steady-burning. The headlamps shall be marked in accordance with FMVSS No... this paragraph. (b) Auxiliary driving lamps and front fog lamps. Commercial motor vehicles may be... aim of the lighting device from being disturbed while the vehicle is operating on public roads. (d...

Electronic Paint: Understanding Children's Representation through Their Interactions with Digital Paint

ERIC Educational Resources Information Center

Matthews, John; Seow, Peter

2007-01-01

This article investigates very young children's use of a stylus-driven, electronic painting and drawing on the tablet PC. The authors compare their development in the use of this device with their use of other mark-making media, including those which derive from pencil and paper technologies and also with mouse-driven electronic paintbox programs.…

21 CFR 886.1430 - Ophthalmic contact lens radius measuring device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ophthalmic contact lens radius measuring device... lens radius measuring device. (a) Identification. An ophthalmic contact lens radius measuring device is... lens. (b) Classification. Class I (general controls). The device is exempt from the premarket...

21 CFR 886.1460 - Stereopsis measuring instrument.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Stereopsis measuring instrument. 886.1460 Section... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1460 Stereopsis measuring instrument. (a) Identification. A stereopsis measuring instrument is a device intended to measure depth...

Radiographic evaluation of vessel count and density with quantitative magnetic resonance imaging during external breast expansion in Asian women: A prospective clinical trial.

PubMed

Myung, Yujin; Kwon, Heeyeon; Pak, Changsik; Lee, Hobin; Jeong, Jae Hoon; Heo, Chan Yeong

2016-12-01

Breast augmentation with fat transfer does not bear the risks associated with silicone implantation. The method can potentially be especially useful in Asian women, who often reject augmentation mammoplasty with implants. This prospective clinical trial evaluated the effects of external breast expansion on breast density and vessel count using magnetic resonance imaging. Thirty-four enrolled patients were instructed to apply one of two devices, the conventional BRAVA device (used in the AESTES trial) or a novel external expansion device (EVERA) designed for Asian women, continuously for 8 h per day for 12 weeks. For external expansion, the pressure was set to 25 mmHg. Follow-up examinations were performed for 4 weeks after completion of the expansion. The ratio between the fibroglandular and adipose tissues of the breast was measured using T1-weighted MRI, and the number of vessels in the breast tissue was determined before and after the treatment by contrast MRI. Additionally, the volume of the breast was measured by laser scanning before, during, and after the device application. The obtained measurements were compared within and between the groups at different time points. Six patients dropped out, while 28 completed the trial without major side effects or adverse events. External expansion significantly increased breast vessel count in both the EVERA and AESTES groups (p = 0.019, p = 0.022). However, it did not significantly change breast density in either group (p = 0.186, p = 0.638). No significant intergroup differences were noted in vessel count (p = 0.874) or density (p = 0.482). Breast volume increases after 12 weeks of application were statistically significant in both groups, with mean changes of 81 ± 22 cc (AESTES) and 98 ± 30 cc (EVERA) (p < 0.001 in both cases). External expansion resulted in a marked increase in breast vessel count but did not affect breast density. The observed increase in breast volume can be considered substantial for Asian women. Level II, therapeutic study. Copyright © 2016 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.