A Comparative Analysis of the Influence of Surface Mining on Hydrological and Geochemical Response of Selected Headwater Streams in the Elk Valley, British Columbia, Canada.

NASA Astrophysics Data System (ADS)

Carey, S. K.; Shatilla, N. J.; Szmudrowska, B.; Rastelli, J.; Wellen, C.

2014-12-01

Surface mining is a common method of accessing coal. Blasting of overburden rock allows access to mineable ore. In high-elevation environments, the removed overburden rock is deposited in adjacent valleys as waste rock spoils. As part of a multi-year R&D program examining the influence of surface mining on watershed hydrological and water quality responses in the Elk Valley, British Columbia, this study reports on how surface mining affects streamflow hydrological and geochemical response at four reference and four mine-influenced catchments. The hydrology of this environment is dominated by snowmelt and steep topographic gradients. Flows were attenuated in mine-influenced catchments, with spring freshet delayed and more muted responses to precipitation events observed. Dissolved ions were an order of magnitude greater in mine-influenced streams, with more dilution-based responses to flows compared with chemostatic behavior observed in reference streams. Stable isotope signatures in stream water suggested that in both mine-influenced and reference watersheds, stream water was derived from well mixed groundwater as annual variability of stream isotope signatures was dampened compared with precipitation signatures. However, deflection of stream isotopes in response to precipitation were more apparent in reference watersheds. As a group, mine influenced catchments had a heavier isotope signature than reference watersheds, suggesting an enhanced influence of rainfall on recharge. Transit time distributions indicate existing waste rock spoils increase the average time water takes to move through the catchment.

Environmental performance and financial report integrity: challenges for the mining sector in Indonesia

NASA Astrophysics Data System (ADS)

Mayangsari, S.

2018-01-01

This study investigates the influence of environmental performance on the financial report integrity. The statistics used were primary data from interviews with senior members of the mining sector regarding environmental issues, as well as secondary data using Financial Report 2016. The samples were listed mining companies with semester data. Questionnaires were used to measure their perceptions of the challenges concerning climate change faced by the mining sector. The results of this research show that regulatory interventions will be critical to environmental issues. This study employed KLD as a proxy for environmental performance, correlated with other variables regarding the integrity of disclosure. The outcome indicates that environmental issues will increase the integrity of financial reports.

The Research on the Impact of Management Level's Charismatic Leadership Style on Miners' Unsafe Behavior.

PubMed

Li, Hongxia; Di, Hongxi; Tian, Shuicheng; Li, Jian

2015-01-01

The aim of this study is research the impact of management level's charismatic leadership style on miners' unsafe behavior by using the questionnaires on charismatic leadership style, safety attitude and the miners' unsafe behavior measurement to investigate 200 employees in Shen Dong Company. The research results suggest that management level's charismatic leadership style have very important influence on miners' unsafe behavior and the influence is affected by the safety attitude which is the intermediary function. In the end, this study propose advice on how to improve the coal mine enterprise managers charismatic leadership style in the coal mine enterprise's safety management work, including attach great importance to a variety of incentive methods, set up safety moral models, practice of inductive leadership concept, create a good atmosphere of safety, etc for reference for coal mining enterprises.

Heavy Metal Concentrations in Soils and Factors Affecting Metal Uptake by Plants in the Vicinity of a Korean Cu-W Mine.

PubMed

Jung, Myung Chae

2008-04-04

Heavy metal concentrations were measured in soils and plants in and around a copper-tungsten mine in southeast Korea to investigate the influence of past base metal mining on the surface environment. The results of chemical analysis indicate that the heavy metals in soils decreased with distance from the source, controlled mainly by water movement and topography. The metal concentrations measured in plant species generally decreased in the order; spring onions > soybean leaves > perilla leaves » red pepper > corn grains » jujube grains, although this pattern varied moderately between different elements. The results agree with other reports that metal concentrations in leaves are usually much higher than those in grain. Factors influencing the bioavailability of metals and their occurrences in crops were found as soil pH, cation exchange capacity, organic matter content, soil texture, and interaction among the target elements. It is concluded that total metal concentrations in soils are the main controls on their contents in plants. Soil pH was also an important factor. A stepwise linear multiple regression analysis was also conducted to identify the dominant factors influencing metal uptake by plants. Metal concentrations in plants were also estimated by computer-aided statistical methods.

Analysis of gob gas venthole production performances for strata gas control in longwall mining.

PubMed

Karacan, C Özgen

2015-10-01

Longwall mining of coal seams affects a large area of overburden by deforming it and creating stress-relief fractures, as well as bedding plane separations, as the mining face progresses. Stress-relief fractures and bedding plane separations are recognized as major pathways for gas migration from gas-bearing strata into sealed and active areas of the mines. In order for strata gas not to enter and inundate the ventilation system of a mine, gob gas ventholes (GGVs) can be used as a methane control measure. The aim of this paper is to analyze production performances of GGVs drilled over a longwall panel. These boreholes were drilled to control methane emissions from the Pratt group of coals due to stress-relief fracturing and bedding plane separations into a longwall mine operating in the Mary Lee/Blue Creek coal seam of the Upper Pottsville Formation in the Black Warrior Basin, Alabama. During the course of the study, Pratt coal's reservoir properties were integrated with production data of the GGVs. These data were analyzed by using material balance techniques to estimate radius of influence of GGVs, gas-in-place and coal pressures, as well as their variations during mining. The results show that the GGVs drilled to extract gas from the stress-relief zone of the Pratt coal interval is highly effective in removing gas from the Upper Pottsville Formation. The radii of influence of the GGVs were in the order of 330-380 m, exceeding the widths of the panels, due to bedding plane separations and stress relieved by fracturing. Material balance analyses indicated that the initial pressure of the Pratt coals, which was around 648 KPa when longwall mining started, decreased to approximately 150 KPa as the result of strata fracturing and production of released gas. Approximately 70% of the initial gas-in-place within the area of influence of the GGVs was captured during a period of one year.

The Research on the Impact of Management Level’s Charismatic Leadership Style on Miners' Unsafe Behavior

PubMed Central

Li, Hongxia; Di, Hongxi; Tian, Shuicheng; Li, Jian

2015-01-01

The aim of this study is research the impact of management level’s charismatic leadership style on miners' unsafe behavior by using the questionnaires on charismatic leadership style, safety attitude and the miners' unsafe behavior measurement to investigate 200 employees in Shen Dong Company. The research results suggest that management level’s charismatic leadership style have very important influence on miners' unsafe behavior and the influence is affected by the safety attitude which is the intermediary function. In the end, this study propose advice on how to improve the coal mine enterprise managers charismatic leadership style in the coal mine enterprise's safety management work, including attach great importance to a variety of incentive methods, set up safety moral models, practice of inductive leadership concept, create a good atmosphere of safety, etc for reference for coal mining enterprises. PMID:26628936

The influence of the fault zone width on land surface vibrations after the high-energy tremor in the "Rydułtowy-Anna" hard coal mine

NASA Astrophysics Data System (ADS)

Pilecka, Elżbieta; Szwarkowski, Dariusz

2018-04-01

In the article, a numerical analysis of the impact of the width of the fault zone on land surface tremors on the area of the "Rydułtowy - Anna" hard coal mine was performed. The analysis covered the dynamic impact of the actual seismic wave after the high-energy tremor of 7 June 2013. Vibrations on the land surface are a measure of the mining damage risk. It is particularly the horizontal components of land vibrations that are dangerous to buildings which is reflected in the Mining Scales of Intensity (GSI) of vibrations. The run of a seismic wave in the rock mass from the hypocenter to the area's surface depends on the lithology of the area and the presence of fault zones. The rock mass network cut by faults of various widths influences the amplitude of tremor reaching the area's surface. The analysis of the impact of the width of the fault zone was done for three alternatives.

Research of land resources comprehensive utilization of coal mining in plain area based on GIS: case of Panyi Coal Mine of Huainan Mining Group Corp.

NASA Astrophysics Data System (ADS)

Dai, Chunxiao; Wang, Songhui; Sun, Dian; Chen, Dong

2007-06-01

The result of land use in coalfield is important to sustainable development in resourceful city. For surface morphology being changed by subsidence, the mining subsidence becomes the main problem to land use with the negative influence of ecological environment, production and steadily develop in coal mining areas. Taking Panyi Coal Mine of Huainan Mining Group Corp as an example, this paper predicted and simulated the mining subsidence in Matlab environment on the basis of the probability integral method. The change of land use types of early term, medium term and long term was analyzed in accordance with the results of mining subsidence prediction with GIS as a spatial data management and spatial analysis tool. The result of analysis showed that 80% area in Panyi Coal Mine be affected by mining subsidence and 52km2 perennial waterlogged area was gradually formed. The farmland ecosystem was gradually turned into wetland ecosystem in most study area. According to the economic and social development and natural conditions of mining area, calculating the ecological environment, production and people's livelihood, this paper supplied the plan for comprehensive utilization of land resource. In this plan, intervention measures be taken during the coal mining and the mining subsidence formation and development, and this method can solve the problems of Land use at the relative low cost.

Infiltration and soil erosion modelling on Lausatian post mine sites

NASA Astrophysics Data System (ADS)

Kunth, Franziska; Schmidt, Jürgen

2013-04-01

Land management of reclaimed lignite mine sites requires long-term and safe structuring of recultivation areas. Erosion by water leads to explicit soil losses, especially on heavily endangered water repellent and non-vegetated soil surfaces. Beyond that, weathering of pyrite-containing lignite burden dumps causes sulfuric acid-formation, and hence the acidification of groundwater, seepage water and surface waters. Pyrite containing sediment is detached by precipitation and transported into worked-out open cuts by draining runoff. In addition to ground water influence, erosion processes are therefore involved in acidification of surface waters. A model-based approach for the conservation of man-made slopes of post mining sites is the objective of this ongoing study. The study shall be completed by modeling of the effectiveness of different mine site recultivation scenarios. Erosion risks on man-made slopes in recultivation areas should be determined by applying the physical, raster- and event based computer model EROSION 2D/3D (Schmidt, 1991, 1992; v. Werner, 1995). The widely used erosion model is able to predict runoff as well as detachment, transport and deposition of sediments. Lignite burden dumps contain hydrophobic substances that cover soil particles. Consequently, these soils show strong water repellency, which influences the processes of infiltration and soil erosion on non-vegetated, coal containing dump soils. The influence of water repellency had to be implemented into EROSION 2D/3D. Required input data for soil erosion modelling (e.g. physical soil parameters, infiltration rates, calibration factors, etc.) were gained by soil sampling and rainfall experiments on non-vegetated as well as recultivated reclaimed mine sites in the Lusatia lignite mining region (southeast of Berlin, Germany). The measured infiltration rates on the non-vegetated water repellent sites were extremely low. Therefore, a newly developed water repellency-factor was applied to depict infiltration and erosion processes on water repellent dump soils. For infiltration modelling with EROSION 2D calibration factors (e.g. water repellency factor, skin-factor, etc.) were determined in different steps by calibrating computer modelled infiltration, respectively volume rate of flow to the measured data.

Long-Term Changes In The Shallow Water Table In A Mining Area: The Lubin-Glogow Copper Region, Southwestern Poland

NASA Astrophysics Data System (ADS)

Bochenska, T.; Limisiewicz, P.; Loprawski, L.

1995-03-01

In regions of intense mining, shortages of water are common. Increased water demand is normally associated with industry in mining areas, and mine unwatering has negative effects on the natural groundwater balance. The study area occupies 3,300 square kilometers within the copper mining region of Lubin-Glogow, southwestern Poland. Pumping of groundwater to drain mines has created a cone of depression that underlies 2,500 square kilometers. The lowering of potentiometric surfaces has occurred in deep aquifers, which are isolated from the surface by thick confining units (loams and clays). Changes of hydraulic head in the shallow aquifer have not previously been observed. In this study, the authors analyzed the water-table changes in the shallow aquifer. The statistical analysis of the water table was based on two sets of water-level measurements in about 1,200 farm wells during dry seasons. The first set was done in the fall of 1986, the second in the fall of 1991. In addition to these measurements, multi-seasonal observations were made by the mining survey in several tens of wells. During five years, the head declined an average of 0.4 meter. Locally, the lowering was as great as five meters. The regional decline of head resulted in a loss of water resources about 2×108 cubic meters. Regionally, this loss is not directly related to the dewatering of copper mines. Locally, however, mining activity strongly influences the water table. The general trend of the decline is probably an effect of decreasing precipitation.

Flooding and arsenic contamination: Influences on ecosystem structure and function in an Appalachian headwater stream

Treesearch

Noah R. Lottig; H. Maurice Valett; Madeline E. Schreiber; Jackson R. Webster

2007-01-01

We investigated the influence of flooding and chronic arsenic contamination on ecosystem structure and function in a headwater stream adjacent to an abandoned arsenic (As) mine using an upstream (reference) and downstream (mine-influenced) comparative reach approach. In this study, floods were addressed as a pulse disturbance, and the abandoned As mine was...

The persistence of lead from past gasoline emissions and mining drainage in a large riparian system: Evidence from lead isotopes in the Sacramento River, California

USGS Publications Warehouse

Dunlap, C.E.; Alpers, Charles N.; Bouse, R.; Taylor, Howard E.; Unruh, D.M.; Flegal, A.R.

2008-01-01

Lead concentrations and isotope ratios measured in river water colloids and streambed sediment samples along 426 km of the Sacramento River, California reveal that the influence of lead from the historical mining of massive sulfide deposits in the West Shasta Cu-mining district (at the headwaters of the Sacramento River) is confined to a 60 km stretch of river immediately downstream of that mining region, whereas inputs from past leaded gasoline emissions and historical hydraulic Au-mining in the Sierra Nevadan foothills are the dominant lead sources in the remaining 370 km of the river. Binary mixing calculations suggest that more than 50% of the lead in the Sacramento River outside of the region of influence of the West Shasta Cu-mining district is derived from past depositions of leaded gasoline emissions. This predominance is the first direct documentation of the geographic extent of gasoline lead persistence throughout a large riparian system (>160,000 km2) and corroborates previous observations based on samples taken at the mouth of the Sacramento River. In addition, new analyses of sediment samples from the hydraulic gold mines of the Sierra Nevada foothills confirm the present-day fluxes into the Sacramento River of contaminant metals derived from historical hydraulic Au-mining that occurred during the latter half of the 19th and early part of the 20th centuries. These fluxes occur predominantly during periods of elevated river discharge associated with heavy winter precipitation in northern California. In the broadest context, the study demonstrates the potential for altered precipitation patterns resulting from climate change to affect the mobility and transport of soil-bound contaminants in the surface environment. ?? 2008 Elsevier Ltd.

Influence of continuous mining arrangements on respirable dust exposures

PubMed Central

Beck, T. W.; Organiscak, J. A.; Pollock, D. E.; Potts, J. D.; Reed, W. R.

2017-01-01

In underground continuous mining operations, ventilation, water sprays and machine-mounted flooded-bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements — such as face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation and equipment operator positioning — can have impacts on the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Pittsburgh Mining Research Division for remote-controlled continuous mining machine operators as well as haulage operators at 10 U.S. underground mines. The results of these respirable dust surveys show that continuous miner exposures varied little with depth of cut but are significantly higher with exhaust ventilation. Haulage operators experienced elevated concentrations with blowing face ventilation. Elevated dust concentrations were observed for both continuous miner operators and haulage operators when working in crosscuts driven into or counter to the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposures attributable to particular mining configurations. These findings form the basis for recommendations for lowering face worker respirable dust exposures. PMID:28529441

Influence of ore processing activity on Hg, As and Sb contamination and fractionation in soils in a former mining site of Monte Amiata ore district (Italy).

PubMed

Protano, Giuseppe; Nannoni, Francesco

2018-05-01

A geochemical study was carried out at the former Abbadia San Salvatore (ASS) mining site of the Monte Amiata ore district (Italy). Hg, As and Sb total contents and fractionation using a sequential extraction procedure were determined in soil and mining waste samples. Ore processing activities provided a different contribution to Hg contamination and concentration in soil fractions, influencing its behaviour as volatility and availability. Soils of roasting zone showed the highest Hg contamination levels mainly due to the deposition of Hg released as Hg 0 by furnaces during cinnabar roasting. High Hg contents were also measured in waste from the lower part of mining dump due to the presence of cinnabar. The fractionation pattern suggested that Hg was largely as volatile species in both uncontaminated and contaminated soils and mining waste, and concentrations of these Hg species increased as contamination increased. These findings were in agreement with the fact that the ASS mining site is characterized by high Hg concentrations in the air and the presence of Hg 0 liquid droplets in soil. Volatile Hg species were also prevalent in uncontaminated soils likely because the Monte Amiata region is an area characterized by anomalous fluxes of gaseous Hg from natural and anthropogenic inputs. At the ASS mining site soils were also contaminated by Sb, while As contents were comparable with its local background in soil. In all soil and waste samples Sb and As were preferentially in residual fraction. Copyright © 2018 Elsevier Ltd. All rights reserved.

Mercury methylation influenced by areas of past mercury mining in the Terlingua district, Southwest Texas, USA

USGS Publications Warehouse

Gray, J.E.; Hines, M.E.; Biester, H.

2006-01-01

Speciation and microbial transformation of Hg was studied in mine waste from abandoned Hg mines in SW Texas to evaluate the potential for methyl-Hg production and degradation in mine wastes. In mine waste samples, total Hg, ionic Hg2+, Hg0, methyl-Hg, organic C, and total S concentrations were measured, various Hg compounds were identified using thermal desorption pyrolysis, and potential rates of Hg methylation and methyl-Hg demethylation were determined using isotopic-tracer methods. These data are the first reported for Hg mines in this region. Total Hg and methyl-Hg concentrations were also determined in stream sediment collected downstream from two of the mines to evaluate transport of Hg and methylation in surrounding ecosystems. Mine waste contains total Hg and methyl-Hg concentrations as high as 19,000 ??g/g and 1500 ng/g, respectively, which are among the highest concentrations reported at Hg mines worldwide. Pyrolysis analyses show that mine waste contains variable amounts of cinnabar, metacinnabar, Hg0, and Hg sorbed onto particles. Methyl-Hg concentrations in mine waste correlate positively with ionic Hg2+, organic C, and total S, which are geochemical parameters that influence processes of Hg cycling and methylation. Net methylation rates were as high as 11,000 ng/g/day, indicating significant microbial Hg methylation at some sites, especially in samples collected inside retorts. Microbially-mediated methyl-Hg demethylation was also observed in many samples, but where both methylation and demethylation were found, the potential rate of methylation was faster. Total Hg concentrations in stream sediment samples were generally below the probable effect concentration of 1.06 ??g/g, the Hg concentration above which harmful effects are likely to be observed in sediment dwelling organisms; whereas total Hg concentrations in mine waste samples were found to exceed this concentration, although this is a sediment quality guideline and is not directly applicable to mine waste. Although total Hg and methyl-Hg concentrations are locally high in some mine waste samples, little Hg appears to be exported from these Hg mines in stream sediment primarily due to the arid climate and lack of precipitation and mine runoff in this region. ?? 2006 Elsevier Ltd. All rights reserved.

National Conference on Mining-Influenced Waters: Approaches for Characterization, Source Control and Treatment

EPA Science Inventory

The conference goal was to provide a forum for the exchange of scientific information on current and emerging approaches to assessing characterization, monitoring, source control, treatment and/or remediation on mining-influenced waters. The conference was aimed at mining remedi...

Gravimetric surveys for assessing rock mass condition around a mine shaft

NASA Astrophysics Data System (ADS)

Madej, Janusz

2017-06-01

The fundamentals of use of vertical gravimetric surveying method in mine shafts are presented in the paper. The methods of gravimetric measurements and calculation of interval and complex density are discussed in detail. The density calculations are based on an original method accounting for the gravity influence of the mine shaft thus guaranteeing closeness of calculated and real values of density of rocks beyond the shaft lining. The results of many gravimetric surveys performed in shafts are presented and interpreted. As a result, information about the location of heterogeneous zones of work beyond the shaft lining is obtained. In many cases, these zones used to threaten the safe operation of machines and utilities in the shaft.

Control technique of spontaneous combustion in fully mechan ized stope during period of end caving under complex mining influence

NASA Astrophysics Data System (ADS)

Yuan, Benqing

2018-01-01

In view of the phenomenon of spontaneous combustion of coal seam occurring during the period of end caving under complex mining conditions, taking the 1116 (3) stope of Guqiao mine as the object of study, the causes of spontaneous combustion during the period of end caving are analyzed, according to the specific geological conditions of the stope to develop corresponding fire prevention measures, including the reduction of air supply and air leakage in goaf, reduce the amount of coal left, reasonable drainage, nitrogen injection for spontaneous combustion prevention, grouting for spontaneous combustion prevention and permanent closure, fundamentally eliminates the potential for spontaneous combustion during the period of 1116(3) stope end caving. The engineering practice shows that this kind of measure has reference value for the prevention and control of spontaneous combustion during the period of stope end caving.

Monitoring of the mercury mining site Almadén implementing remote sensing technologies.

PubMed

Schmid, Thomas; Rico, Celia; Rodríguez-Rastrero, Manuel; José Sierra, María; Javier Díaz-Puente, Fco; Pelayo, Marta; Millán, Rocio

2013-08-01

The Almadén area in Spain has a long history of mercury mining with prolonged human-induced activities that are related to mineral extraction and metallurgical processes before the closure of the mines and a more recent post period dominated by projects that reclaim the mine dumps and tailings and recuperating the entire mining area. Furthermore, socio-economic alternatives such as crop cultivation, livestock breeding and tourism are increasing in the area. Up till now, only scattered information on these activities is available from specific studies. However, improved acquisition systems using satellite borne data in the last decades opens up new possibilities to periodically study an area of interest. Therefore, comparing the influence of these activities on the environment and monitoring their impact on the ecosystem vastly improves decision making for the public policy makers to implement appropriate land management measures and control environmental degradation. The objective of this work is to monitor environmental changes affected by human-induced activities within the Almadén area occurring before, during and after the mine closure over a period of nearly three decades. To achieve this, data from numerous sources at different spatial scales and time periods are implemented into a methodology based on advanced remote sensing techniques. This includes field spectroradiometry measurements, laboratory analyses and satellite borne data of different surface covers to detect land cover and use changes throughout the mining area. Finally, monitoring results show that the distribution of areas affected by mercury mining is rapidly diminishing since activities ceased and that rehabilitated mining areas form a new landscape. This refers to mine tailings that have been sealed and revegetated as well as an open pit mine that has been converted to an "artificial" lake surface. Implementing a methodology based on remote sensing techniques that integrate data from several sources at different scales greatly improves the regional characterization and monitoring of an area dominated by mercury mining activities. Copyright © 2013 Elsevier Inc. All rights reserved.

Complex Feeding Tracks of the Sessile Herbivorous Insect Ophiomyia maura as a Function of the Defense against Insect Parasitoids

PubMed Central

Ayabe, Yoshiko; Ueno, Takatoshi

2012-01-01

Because insect herbivores generally suffer from high mortality due to their natural enemies, reducing the risk of being located by natural enemies is of critical importance for them, forcing them to develop a variety of defensive measures. Larvae of leaf-mining insects lead a sedentary life inside a leaf and make conspicuous feeding tracks called mines, exposing themselves to the potential risk of parasitism. We investigated the defense strategy of the linear leafminer Ophiomyia maura Meigen (Diptera: Agromyzidae), by focusing on its mining patterns. We examined whether the leafminer could reduce the risk of being parasitized (1) by making cross structures in the inner area of a leaf to deter parasitoids from tracking the mines due to complex pathways, and (2) by mining along the edge of a leaf to hinder visually searching parasitoids from finding mined leaves due to effective background matching of the mined leaves among intact leaves. We quantified fractal dimension as mine complexity and area of mine in the inner area of the leaf as interior mine density for each sample mine, and analyzed whether these mine traits affected the susceptibility of O. maura to parasitism. Our results have shown that an increase in mine complexity with the development of occupying larvae decreases the probability of being parasitized, while interior mine density has no influence on parasitism. These results suggest that the larval development increases the host defense ability through increasing mine complexity. Thus the feeding pattern of these sessile insects has a defensive function by reducing the risk of parasitism. PMID:22393419

A New Conception of Bucket Wheel Excavator Cab and Seat Mounting

NASA Astrophysics Data System (ADS)

Blekta, J.; Mevald, J.; Petríková, I.; Petříček, J.; Lufinka, A.

One of the most important problem of coal mining by bucket wheel excavators is how to minimize influence of vibrations on driver's body. Project of Ministry of Trade and Industry of the Czech Republic solved in Technical University of Liberec was engaged in this problem. The aim of this project was to design a new cab and seat mounting of wheel excavator Schrs 1320. A suitable possibilities of cab suspensions were investigated to minimize driver body vibrations and to improve influence of mining process to drivers health. After optimization one concept was chosen. A new methodic of measured data evaluation was created for using in excavators as well as in laboratory. The new concept of dynamic seat absorber were designed also.

Occupational hazard evaluation model underground coal mine based on unascertained measurement theory

NASA Astrophysics Data System (ADS)

Deng, Quanlong; Jiang, Zhongan; Sun, Yaru; Peng, Ya

2017-05-01

In order to study how to comprehensively evaluate the influence of several occupational hazard on miners’ physical and mental health, based on unascertained measurement theory, occupational hazard evaluation indicator system was established to make quantitative and qualitative analysis. Determining every indicator weight by information entropy and estimating the occupational hazard level by credible degree recognition criteria, the evaluation model was programmed by Visual Basic, applying the evaluation model to occupational hazard comprehensive evaluation of six posts under a coal mine, and the occupational hazard degree was graded, the evaluation results are consistent with actual situation. The results show that dust and noise is most obvious among the coal mine occupational hazard factors. Excavation face support workers are most affected, secondly, heading machine drivers, coal cutter drivers, coalface move support workers, the occupational hazard degree of these four types workers is II mild level. The occupational hazard degree of ventilation workers and safety inspection workers is I level. The evaluation model could evaluate underground coal mine objectively and accurately, and can be employed to the actual engineering.

Mechanisms and Effectivity of Sulfate Reducing Bioreactors Using a Chitinous Substrate in Treating Mining Influenced Water

EPA Science Inventory

Mining-influenced water (MIW) is the main environmental challenge associated with the mining industry. Passive MIW remediation can be achieved through microbial activity in sulfate-reducing bioreactors (SRBRs), but their actual removal rates depend on different factors, one of wh...

The Adoption of the Arcgis System to Support the Analyses of the Influence of the Mining Tremors on the Building Objects

NASA Astrophysics Data System (ADS)

Sokoła-Szewioła, Violetta; Żogała, Monika

2016-12-01

Nowadays the mining companies use the Spatial Information System in order to facilitate data management, gathered during the mining activity. For these purposes various kinds of applications and software information are used. They allow for faster and easier data processing. In the paper there are presented the possibilities of using the ArcGIS system to support the tasks performed in the mining industry in the scope of the analysis of the influence of the mining tremors, induced by the longwall exploitation on the facilities construction sited on the surface area. These possibilities are presented by the example of the database developed for the coal mine KWK "Rydułtowy-Anna." The developed database was created using ArcGIS software for Desktop 10. 1. It contains the values of parameters, specified for its implementation relevant to the analyses of the influence of the mining tremors on the surface structures.

Speciation and leachability of copper in mine tailings from porphyry copper mining: influence of particle size.

PubMed

Hansen, Henrik K; Yianatos, Juan B; Ottosen, Lisbeth M

2005-09-01

Mine tailing from the El Teniente-Codelco copper mine situated in VI Region of Chile was analysed in order to evaluate the mobility and speciation of copper in the solid material. Mine tailing was sampled after the rougher flotation circuits, and the copper content was measured to 1150 mg kg (-1) dry matter. This tailing was segmented into fractions of different size intervals: 0-38, 38-45, 45-53, 53-75, 75-106, 106-150, 150-212, and >212 microm, respectively. Copper content determination, sequential chemical extraction, and desorption experiments were carried out for each size interval in order to evaluate the speciation of copper. It was found that the particles of smallest size contained 50-60% weak acid leachable copper, whereas only 32% of the copper found in largest particles could be leached in weak acid. Copper oxides and carbonates were the dominating species in the smaller particles, and the larger particles contained considerable amounts of sulphides.

Biosorption Of Heavy Metals From Mining Influenced Water Onto Chitin Products

EPA Science Inventory

Mining influenced water (MIW) emanating from mine sites poses a major environmental concern due to its impact on water contamination caused by low pH and the presence of high concentrations of toxic metals. Chitorem SC-20^® (raw crushed crab shells containing 40% w/w C...

Biomonitoring of lead, zinc, and cadmium in streams draining lead-mining and non-mining areas, Southeast Missouri, USA

USGS Publications Warehouse

Besser, John M.; Brumbaugh, William G.; May, Thomas W.; Schmitt, Christopher J.

2007-01-01

We evaluated exposure of aquatic biota to lead (Pb), zinc (Zn), and cadmium (Cd) in streams draining a Pb-mining district in southeast Missouri. Samples of plant biomass (detritus, periphyton, and filamentous algae), invertebrates (snails, crayfish, and riffle benthos), and two taxa of fish were collected from seven sites closest to mining areas (mining sites), four sites further downstream from mining (downstream sites), and eight reference sites in fall 2001. Samples of plant biomass from mining sites had highest metal concentrations, with means 10- to 60-times greater than those for reference sites. Mean metal concentrations in over 90% of samples of plant biomass from mining sites were significantly greater than those from reference sites. Mean concentrations of Pb, Zn, and Cd in most invertebrate samples from mining sites, and mean Pb concentrations in most fish samples from mining sites, were also significantly greater than those from reference sites. Concentrations of all three metals were lower in samples from downstream sites, but several samples of plant biomass from downstream sites had metal concentrations significantly greater than those from reference sites. Analysis of supplemental samples collected in the fall of 2002, a year of above-average stream discharge, had lower Pb concentrations and higher Cd concentrations than samples collected in 2001, near the end of a multi-year drought. Concentrations of Pb measured in fish and invertebrates collected from mining sites during 2001 and 2002 were similar to those measured at nearby sites in the 1970s, during the early years of mining in the Viburnum Trend. Results of this study demonstrate that long-term Pb mining activity in southeast Missouri has resulted in significantly elevated concentrations of Pb, Cd, and Zn in biota of receiving streams, compared to biota of similar streams without direct influence of mining. Our results also demonstrate that metal exposure in the study area differed significantly among sample types, habitats, and years, and that these factors should be carefully considered in the design of biomonitoring studies.

Biomonitoring of lead, zinc, and cadmium in streams draining lead-mining and non-mining areas, Southeast Missouri, USA

USGS Publications Warehouse

Besser, J.M.; Brumbaugh, W.G.; May, T.W.; Schmitt, C.J.

2007-01-01

We evaluated exposure of aquatic biota to lead (Pb), zinc (Zn), and cadmium (Cd) in streams draining a Pb-mining district in southeast Missouri. Samples of plant biomass (detritus, periphyton, and filamentous algae), invertebrates (snails, crayfish, and riffle benthos), and two taxa of fish were collected from seven sites closest to mining areas (mining sites), four sites further downstream from mining (downstream sites), and eight reference sites in fall 2001. Samples of plant biomass from mining sites had highest metal concentrations, with means 10- to 60-times greater than those for reference sites. Mean metal concentrations in over 90% of samples of plant biomass from mining sites were significantly greater than those from reference sites. Mean concentrations of Pb, Zn, and Cd in most invertebrate samples from mining sites, and mean Pb concentrations in most fish samples from mining sites, were also significantly greater than those from reference sites. Concentrations of all three metals were lower in samples from downstream sites, but several samples of plant biomass from downstream sites had metal concentrations significantly greater than those from reference sites. Analysis of supplemental samples collected in the fall of 2002, a year of above-average stream discharge, had lower Pb concentrations and higher Cd concentrations than samples collected in 2001, near the end of a multi-year drought. Concentrations of Pb measured in fish and invertebrates collected from mining sites during 2001 and 2002 were similar to those measured at nearby sites in the 1970s, during the early years of mining in the Viburnum Trend. Results of this study demonstrate that long-term Pb mining activity in southeast Missouri has resulted in significantly elevated concentrations of Pb, Cd, and Zn in biota of receiving streams, compared to biota of similar streams without direct influence of mining. Our results also demonstrate that metal exposure in the study area differed significantly among sample types, habitats, and years, and that these factors should be carefully considered in the design of biomonitoring studies. ?? Springer Science+Business Media B.V. 2006.

Automated information and control complex of hydro-gas endogenous mine processes

NASA Astrophysics Data System (ADS)

Davkaev, K. S.; Lyakhovets, M. V.; Gulevich, T. M.; Zolin, K. A.

2017-09-01

The automated information and control complex designed to prevent accidents, related to aerological situation in the underground workings, accounting of the received and handed over individual devices, transmission and display of measurement data, and the formation of preemptive solutions is considered. Examples for the automated workplace of an airgas control operator by individual means are given. The statistical characteristics of field data characterizing the aerological situation in the mine are obtained. The conducted studies of statistical characteristics confirm the feasibility of creating a subsystem of controlled gas distribution with an adaptive arrangement of points for gas control. The adaptive (multivariant) algorithm for processing measuring information of continuous multidimensional quantities and influencing factors has been developed.

Sampling and monitoring for the mine life cycle

USGS Publications Warehouse

McLemore, Virginia T.; Smith, Kathleen S.; Russell, Carol C.

2014-01-01

Sampling and Monitoring for the Mine Life Cycle provides an overview of sampling for environmental purposes and monitoring of environmentally relevant variables at mining sites. It focuses on environmental sampling and monitoring of surface water, and also considers groundwater, process water streams, rock, soil, and other media including air and biological organisms. The handbook includes an appendix of technical summaries written by subject-matter experts that describe field measurements, collection methods, and analytical techniques and procedures relevant to environmental sampling and monitoring.The sixth of a series of handbooks on technologies for management of metal mine and metallurgical process drainage, this handbook supplements and enhances current literature and provides an awareness of the critical components and complexities involved in environmental sampling and monitoring at the mine site. It differs from most information sources by providing an approach to address all types of mining influenced water and other sampling media throughout the mine life cycle.Sampling and Monitoring for the Mine Life Cycle is organized into a main text and six appendices that are an integral part of the handbook. Sidebars and illustrations are included to provide additional detail about important concepts, to present examples and brief case studies, and to suggest resources for further information. Extensive references are included.

A Comparative Study to Predict Student’s Performance Using Educational Data Mining Techniques

NASA Astrophysics Data System (ADS)

Uswatun Khasanah, Annisa; Harwati

2017-06-01

Student’s performance prediction is essential to be conducted for a university to prevent student fail. Number of student drop out is one of parameter that can be used to measure student performance and one important point that must be evaluated in Indonesia university accreditation. Data Mining has been widely used to predict student’s performance, and data mining that applied in this field usually called as Educational Data Mining. This study conducted Feature Selection to select high influence attributes with student performance in Department of Industrial Engineering Universitas Islam Indonesia. Then, two popular classification algorithm, Bayesian Network and Decision Tree, were implemented and compared to know the best prediction result. The outcome showed that student’s attendance and GPA in the first semester were in the top rank from all Feature Selection methods, and Bayesian Network is outperforming Decision Tree since it has higher accuracy rate.

Study on goaf gas control technology of gob-side entry driving

NASA Astrophysics Data System (ADS)

Ren, Qihan; Yuan, Benqing; Li, Qiansi

2018-01-01

The 1112 (1) track gate roadway of Gu Qiao coal mine of Huainan mining group adopt the method of gob-side entry driving, the gas emission is large during the driving of the roadway, the gas in the goaf seriously influences the safe driving of the roadway. Equalizing method, drilling drainage method, jet grouting method and other goaf gas controlling measures has been adopted. Finally, it effectively solves the safety threat of gas in goaf to roadway driving, it provides a good reference for the gas control of the gob-side entry.

Radionuclides and trace metals in Canadian moose near uranium mines: comparison of radiation doses and food chain transfer with cattle and caribou.

PubMed

Thomas, Patricia; Irvine, James; Lyster, Jane; Beaulieu, Rhys

2005-05-01

Tissues from 45 moose and 4 cattle were collected to assess the health of country foods near uranium mines in northern Saskatchewan. Bone, liver, kidney, muscle and rumen contents were analyzed for uranium, radium-226 (226Ra), lead-210 (210Pb), and polonium-210 (210Po). Cesium-137 (137Cs), potassium-40 (40K), and 27 trace metals were also measured in some tissues. Within the most active mining area, Po in liver and muscle declined significantly with distance from tailings, possibly influenced by nearby natural uranium outcrops. Moose from this area had significantly higher 226Ra, 210Pb, 210Po, and 137Cs in some edible soft tissues vs. one control area. However, soil type and diet may influence concentrations as much as uranium mining activities, given that a) liver levels of uranium, 226Ra, and 210Po were similar to a second positive control area with mineral-rich shale hills and b) 210Po was higher in cattle kidneys than in all moose. Enhanced food chain transfer from rumen contents to liver was found for selenium in the main mining area and for copper, molybdenum and cadmium in moose vs. cattle. Although radiological doses to moose in the main mining area were 2.6 times higher than doses to control moose or cattle, low moose intakes yielded low human doses (0.0068 mSv y(-1)), a mere 0.3% of the dose from intake of caribou (2.4 mSv y(-1)), the dietary staple in the area.

The influence of particle size distribution on dose conversion factors for radon progeny in the underground excavations of hard coal mine.

PubMed

Skubacz, Krystian; Wojtecki, Łukasz; Urban, Paweł

2016-10-01

In Polish underground mines, hazards caused by enhanced natural radioactivity occur. The sources of radiation exposure are short-lived radon decay products, mine waters containing radium 226 Ra and 228 Ra and the radioactive sediments that can precipitate out of these waters. For miners, the greatest exposure is usually due to short-lived radon decay products. The risk assessment is based on the measurement of the total potential alpha energy concentration (PAEC) and the evaluation of the related dose by using the dose conversion factor as recommended by relevant legal requirements. This paper presents the results of measurements of particle size distributions of ambient aerosols in an underground hard coal mine, the assessment of the radioactive particle size distribution of the short-lived radon decay products and the corresponding values of dose conversion factors. The measurements of the ambient airborne particle size distribution were performed in the range from a few nanometers to about 20 μm. The study therefore included practically the whole class of respirable particles. The results showed that the high concentration of ultrafine and fine aerosols measured can significantly affect the value of the dose conversion factors, and consequently the corresponding committed effective dose, to which the miners can be exposed. Copyright © 2016 Elsevier Ltd. All rights reserved.

Spatial Variations In The Fate And Transport Of Metals In A Mining-Influenced Stream, North Fork Clear Creek, Colorado

EPA Science Inventory

North Fork Clear Creek (NFCC) receives acid-mine drainage (AMD) from multiple abandoned mines in the Clear Creek Watershed. Point sources of AMD originate In the Black Hawk/Central City region of the stream. Water chemistry also is influenced by several non-point sources of AMD,...

Influence of continuous deformations and tremors of rock mass on a building. Case study

NASA Astrophysics Data System (ADS)

Strzałkowski, Piotr

2018-04-01

This work presents an exemplary analysis of the influence of mining exploitations on a building. Continuous deformations of the ground surface in the location of the object were considered. Analysis of the impact of tremors of rock mass on the object was performed. The results of calculations as well as the measurements of surface vibrations accelerations were taken into account. The performed analyses show the influence of a fault on increase of vibrations accelerations.

Analyzing Conductivity Profiles in Stream Waters Influenced by Mine Water Discharges

NASA Astrophysics Data System (ADS)

Räsänen, Teemu; Hämäläinen, Emmy; Hämäläinen, Matias; Turunen, Kaisa; Pajula, Pasi; Backnäs, Soile

2015-04-01

Conductivity is useful as a general measure of stream water quality. Each stream inclines to have a quite constant range of conductivity that can be used as a baseline for comparing and detecting influence of contaminant sources. Conductivity in natural streams and rivers is affected primarily by the geology of the watershed. Thus discharges from ditches and streams affect not only the flow rate in the river but also the water quality and conductivity. In natural stream waters, the depth and the shape of the river channel change constantly, which changes also the water flow. Thus, an accurate measuring of conductivity or other water quality indicators is difficult. Reliable measurements are needed in order to have holistic view about amount of contaminants, sources of discharges and seasonal variation in mixing and dilution processes controlling the conductivity changes in river system. We tested the utility of CastAway-CTD measuring device (SonTek Inc) to indicate the influence of mine waters as well as mixing and dilution occurring in the recipient river affected by treated dewatering and process effluent water discharges from a Finnish gold mine. The CastAway-CTD measuring device is a small, rugged and designed for profiling of depths of up to 100m. Device measures temperature, salinity, conductivity and sound of speed using 5 Hz response time. It has also built-in GPS which produces location information. CTD casts are normally used to produce vertical conductivity profile for rather deep waters like seas or lakes. We did seasonal multiple Castaway-CTD measurements during 2013 and 2014 and produced scaled vertical and horizontal profiles of conductivity and water temperature at the river. CastAway-CTD measurement pinpoints how possible contaminants behave and locate in stream waters. The conductivity profiles measured by CastAway-CTD device show the variation in maximum conductivity values vertically in measuring locations and horizontally in measured cross-sections. The data from field measurements was combined with detailed water quality analysis and processed by data analysis with Matlab to produce more holistic information about the behavior, mixing and dilution of possible contaminants at the river. Moreover, the results can be used to improve water sampling procedures for more representative sampling and to plan continuous monitoring site locations and measuring device mounting places.

Evaluation of Metal Partitioning and Mobility in a Sulfidic Mine Tailing Pile under Oxic and Anoxic Conditions

EPA Science Inventory

Mining-influenced water emanating from mine tailings and potentially contaminating surface water and groundwater is one of the most important environmental issues linked to the mining industry. In this study, two subsets of Callahan Mine tailings (mainly comprised of silicates, ...

Thermal stress in North Western Australian iron ore mining staff.

PubMed

Peiffer, Jeremiah J; Abbiss, Chris R

2013-05-01

Demand for Australian mined iron ore has increased employment within this sector, thus exposing increased numbers of workers to the harsh Australian climate. This study examined the influence of hot (>30°C wet bulb globe temperature) environmental temperatures, consistent with working in North Western Australia, on iron ore mining staff. Core temperature, hydration status, perceived exertion, mood, and fatigue state were measured in 77 participants at three time points (pre-, mid-, and post-shift) during a normal 12-h shift at an open-cut iron ore mining/processing site (n = 31; Site1) and an iron ore processing/shipping site (n = 46; Site2). A significant effect for time was observed for core temperature with greater mean core temperatures measured mid-shift (37.5±0.4°C) and post-shift (37.6±0.3°C) compared with pre-shift values (37.0±0.5°C). All mean core temperature measures were lower than ISO7933 thresholds (38°C) for thermal safety. Mean hydration measures [urine-specific gravity (USG)] were greater at Site1 (1.029±0.006) compared with those at Site2 (1.021±0.007). Furthermore, both pre- and post-shift measures from Site1 and the post-shift measures from Site2 were greater than the threshold for dehydration (USG = 1.020). No differences were observed for mood or perceived exertion over time; however, measures of fatigue state were greater post-shift compared with pre- and mid-shift values for both sites. Our findings indicate that the majority of mine workers in North Western Australia are able to regulate work rate in hot environments to maintain core temperatures below ISO safety guidelines; however, 22% of workers reached or exceeded the safety guidelines, warranting further investigation. Furthermore, hydration practices, especially when off-work, appear inadequate and could endanger health and safety.

Biochars ability to sequester metals in contaminated mine spoils: A greenhouse study

NASA Astrophysics Data System (ADS)

Novak, Jeff; Johnson, Mark G.; Ippolito, Jim; Spokas, Kurt; Trippe, Kristin; Ducey, Tom; Sigua, Gilbert

2017-04-01

Biochars are under consideration as an amendment to remediate contaminated mine spoils and improving plant growth cover. Scientists from the USDA-ARS, US EPA, and Colorado State University have conducted a greenhouse experiment using Miscanthous (Miscanthus giganteus) biochar produced at 700⁰C to reclaim mine spoils obtained from the Formosa mine site (near Riddle, Oregon, USA). Spoil at this site is acidic and has elevated total and plant available copper (Cu) and zinc (Zn) concentrations. Blue Wildrye (Elymus glaucus) was planted in mine spoil that was treated with Miscanthus biochar at 0, 1, 2.5 and 5% (w/w), lime, and N-P-K fertilizer. Mine spoil treated with biochar alone (no lime) along with samples (no lime or biochar) were also included. After almost 60 days of incubation, above ground and below ground wildrye samples were collected. Remaining spoils were then extracted with Mehlich 3 reagent and plant available Cu and Zn concentrations measured. Mehlich 3 extractable Cu and Zn concentrations decreased significantly only in the lime treated samples—their concentrations were not influenced by biochar. Our preliminary findings are that lime is an important amendment to reduce metal concentrations in mine spoils and that choice of biochar type must be carefully considered beforehand.

Super short term forecasting of photovoltaic power generation output in micro grid

NASA Astrophysics Data System (ADS)

Gong, Cheng; Ma, Longfei; Chi, Zhongjun; Zhang, Baoqun; Jiao, Ran; Yang, Bing; Chen, Jianshu; Zeng, Shuang

2017-01-01

The prediction model combining data mining and support vector machine (SVM) was built. Which provide information of photovoltaic (PV) power generation output for economic operation and optimal control of micro gird, and which reduce influence of power system from PV fluctuation. Because of the characteristic which output of PV rely on radiation intensity, ambient temperature, cloudiness, etc., so data mining was brought in. This technology can deal with large amounts of historical data and eliminate superfluous data, by using fuzzy classifier of daily type and grey related degree. The model of SVM was built, which can dock with information from data mining. Based on measured data from a small PV station, the prediction model was tested. The numerical example shows that the prediction model is fast and accurate.

The Interaction of Economic Rewards and Moral Convictions in Predicting Attitudes toward Resource Use

PubMed Central

Bastian, Brock; Zhang, Airong; Moffat, Kieren

2015-01-01

When people are morally convicted regarding a specific issue, these convictions exert a powerful influence on their attitudes and behavior. In the current research we examined whether there are boundary conditions to the influence of this effect. Specifically, whether in the context of salient economic rewards, moral convictions may become weaker predictors of attitudes regarding resource use. Focusing on the issue of mining we gathered large-scale samples across three different continents (Australia, Chile, and China). We found that moral convictions against mining were related to a reduced acceptance of mining in each country, while perceived economic rewards from mining increased acceptance. These two motivations interacted, however, such that when perceived economic benefit from mining was high, the influence of moral conviction was weaker. The results highlight the importance of understanding the roles of both moral conviction and financial gain in motivating attitudes towards resource use. PMID:26267904

Reconstructing disturbance history for an intensively mined region by time-series analysis of Landsat imagery.

PubMed

Li, Jing; Zipper, Carl E; Donovan, Patricia F; Wynne, Randolph H; Oliphant, Adam J

2015-09-01

Surface mining disturbances have attracted attention globally due to extensive influence on topography, land use, ecosystems, and human populations in mineral-rich regions. We analyzed a time series of Landsat satellite imagery to produce a 28-year disturbance history for surface coal mining in a segment of eastern USA's central Appalachian coalfield, southwestern Virginia. The method was developed and applied as a three-step sequence: vegetation index selection, persistent vegetation identification, and mined-land delineation by year of disturbance. The overall classification accuracy and kappa coefficient were 0.9350 and 0.9252, respectively. Most surface coal mines were identified correctly by location and by time of initial disturbance. More than 8 % of southwestern Virginia's >4000-km(2) coalfield area was disturbed by surface coal mining over the 28-year period. Approximately 19.5 % of the Appalachian coalfield surface within the most intensively mined county (Wise County) has been disturbed by mining. Mining disturbances expanded steadily and progressively over the study period. Information generated can be applied to gain further insight concerning mining influences on ecosystems and other essential environmental features.

Influence of the Haizhou Open Pit Coal Mine on the atmospheric flow over Fuxin, China.

PubMed

Chen, He; Yang, Zhi-Feng; Wang, Xuan

2004-01-01

The influence of the Haizhou Open Pit Mine on the atmospheric flow in nearby Fuxin City in China was analyzed with the aid of the steady-state Navier-Stokes equations. The finite element method was used to obtain numerical solutions to these equations. The results showed that the Haizhou Open Pit Coal Mine contributes to the turbulent flow in the Fuxin City and its surroundings. However, when compared with the climatic effects, the open pit mine has a relatively small impact on the atmospheric flow over Fuxin.

Parameterisation of non-homogeneities in buried object detection by means of thermography

NASA Astrophysics Data System (ADS)

Stepanić, Josip; Malinovec, Marina; Švaić, Srećko; Krstelj, Vjera

2004-05-01

Landmines and their natural environment form a system of complex dynamics with variable characteristics. A manifestation of that complexity within the context of thermography-based landmines detection is excessive noise in thermograms. That has severely suppressed application of thermography in landmines detection for the purposes of humanitarian demining. (To be differentiated from military demining and demining for military operations other than war [Land Mine Detection DOD's Research Program Needs a Comprehensive Evaluation Strategy, US GAO Report, GAO-01 239, 2001; International Mine Action Standards, Chapter 4.--Glossary. Available at: < http://www.mineactionstandards.org/IMAS_archive/Final/04.10.pdf>].) The discrepancy between the existing role and the actual potential of thermography in humanitarian demining motivated systematic approach to sources of noise in thermograms of buried objects. These sources are variations in mine orientation relative to soil normal, which modify the shape of mine signature on thermograms, as well as non-homogeneities in soil and vegetation layer above the mine, which modify the overall quality of thermograms. This paper analyses the influence of variable mines, and more generally the influence of axially symmetric buried object orientation on the quality of its signature on thermograms. The following two angles have been extracted to serve as parameters describing variation in orientation: (i) θ--angle between the local vertical axis and mine symmetry axis and (ii) ψ--angle between local vertical axis and soil surface normal. Their influence is compared to the influence of (iii) d--the object depth change, which serves as control parameter. The influences are quantified and ranked within a statistically planned experiment. The analysis has proved that among the parameters listed, the most influential one is statistical interaction dψ, followed with the statistical interaction dθ. According to statistical tests, these two combinations are considered the most significant influences. The results show that the currently applied analysis of thermography in humanitarian demining must be broadened by the inclusion of the variations in mine orientation, otherwise a decrease in the probability of mine detection, due to the presence of a systematic error, occurs.

Geologic processes influence the effects of mining on aquatic ecosystems

USGS Publications Warehouse

Schmidt, Travis S.; Clements, William H.; Wanty, Richard B.; Verplanck, Philip L.; Church, Stan E.; San Juan, Carma A.; Fey, David L.; Rockwell, Barnaby W.; DeWitt, Ed H.; Klein, Terry L.

2012-01-01

Geologic processes strongly influence water and sediment quality in aquatic ecosystems but rarely are geologic principles incorporated into routine biomonitoring studies. We test if elevated concentrations of metals in water and sediment are restricted to streams downstream of mines or areas that may discharge mine wastes. We surveyed 198 catchments classified as “historically mined” or “unmined,” and based on mineral-deposit criteria, to determine whether water and sediment quality were influenced by naturally occurring mineralized rock, by historical mining, or by a combination of both. By accounting for different geologic sources of metals to the environment, we were able to distinguish aquatic ecosystems limited by metals derived from natural processes from those due to mining. Elevated concentrations of metals in water and sediment were not restricted to mined catchments; depauperate aquatic communities were found in unmined catchments. The type and intensity of hydrothermal alteration and the mineral deposit type were important determinants of water and sediment quality as well as the aquatic community in both mined and unmined catchments. This study distinguished the effects of different rock types and geologic sources of metals on ecosystems by incorporating basic geologic processes into reference and baseline site selection, resulting in a refined assessment. Our results indicate that biomonitoring studies should account for natural sources of metals in some geologic environments as contributors to the effect of mines on aquatic ecosystems, recognizing that in mining-impacted drainages there may have been high pre-mining background metal concentrations.

Imaging Preferential Flow Pathways of Contaminants from Passive Acid Mine Drainage Mitigation Sites Using Electrical Resistivity

NASA Astrophysics Data System (ADS)

Kelley, N.; Mount, G.; Terry, N.; Herndon, E.; Singer, D. M.

2017-12-01

The Critical Zone represents the surficial and shallow layer of rock, air, water, and soil where most interactions between living organisms and the Earth occur. Acid mine drainage (AMD) resulting from coal extraction can influence both biological and geochemical processes across this zone. Conservative estimates suggest that more than 300 million gallons of AMD are released daily, making this acidic solution of water and contaminants a common issue in areas with legacy or current coal extraction. Electrical resistivity imaging (ERI) provides a rapid and minimally invasive method to identify and monitor contaminant pathways from AMD remediation systems in the subsurface of the Critical Zone. The technique yields spatially continuous data of subsurface resistivity that can be inverted to determine electrical conductivity as a function of depth. Since elevated concentrations of heavy metals can directly influence soil conductivity, ERI data can be used to trace the flow pathways or perhaps unknown mine conduits and transport of heavy metals through the subsurface near acid mine drainage sources. This study aims to examine preferential contaminant migration from those sources through substrate pores, fractures, and shallow mine workings in the near subsurface surrounding AMD sites in eastern Ohio and western Pennsylvania. We utilize time lapse ERI measures during different hydrologic conditions to better understand the variability of preferential flow pathways in relation to changes in stage and discharge within the remediation systems. To confirm ERI findings, and provide constraint to geochemical reactions occurring in the shallow subsurface, we conducted Inductively Coupled Plasma (ICP) spectrometry analysis of groundwater samples from boreholes along the survey transects. Through these combined methods, we can provide insight into the ability of engineered systems to contain and isolate metals in passive acid mine drainage treatment systems.

Optimization of digestion parameters for analysing the total sulphur of mine tailings by inductively coupled plasma optical emission spectrometry.

PubMed

Alam, Raquibul; Shang, Julie Q; Cheng, Xiangrong

2012-05-01

The oxidation of sulphidic mine tailings and consequent acid generation poses challenges for the environment. Accurate and precise analysis of sulphur content is necessary for impact assessment and management of mine tailings. Here, the authors aim at developing a rapid and easy digestion procedure, which may analyse and measure the total amount of sulphur in mine tailings by using inductively coupled plasma. For evaluating effects of several variables, the researchers used a univariate (analysis of variance (ANOVA)) strategy and considered factors such as composition of the acid mixture, heating time, and refluxing device to optimize the performance. To do the experiment, the researchers have used two certified reference materials (KZK-1 and RTS-2) and samples of tailings from Musselwhite mine. ANOVA result shows that heating time is the most influencing factor on acid digestion of the reference materials whereas in case of a digestion of tailings sample, hydrochloric acid proved to be the most significant parameter. Satisfactory results between the measured and referenced values are found for all experiments. It is found that the aqua regia (1 ml HNO(3) + 3 ml HCl) digestion of 0.1 g of samples after only 40 min of heating at 95°C produced fast, safe, and accurate analytical results with a recovery of 97% for the selected reference materials.

Deformation Failure Characteristics of Coal Body and Mining Induced Stress Evolution Law

PubMed Central

Wen, Zhijie; Wen, Jinhao; Shi, Yongkui; Jia, Chuanyang

2014-01-01

The results of the interaction between coal failure and mining pressure field evolution during mining are presented. Not only the mechanical model of stope and its relative structure division, but also the failure and behavior characteristic of coal body under different mining stages are built and demonstrated. Namely, the breaking arch and stress arch which influence the mining area are quantified calculated. A systematic method of stress field distribution is worked out. All this indicates that the pore distribution of coal body with different compressed volume has fractal character; it appears to be the linear relationship between propagation range of internal stress field and compressed volume of coal body and nonlinear relationship between the range of outburst coal mass and the number of pores which is influenced by mining pressure. The results provide theory reference for the research on the range of mining-induced stress and broken coal wall. PMID:24967438

Definition of redox and pH influence in the AMD mine system using a fuzzy qualitative tool (Iberian Pyrite Belt, SW Spain).

PubMed

de la Torre, M L; Grande, J A; Valente, T; Perez-Ostalé, E; Santisteban, M; Aroba, J; Ramos, I

2016-03-01

Poderosa Mine is an abandoned pyrite mine, located in the Iberian Pyrite Belt which pours its acid mine drainage (AMD) waters into the Odiel river (South-West Spain). This work focuses on establishing possible reasons for interdependence between the potential redox and pH, with the load of metals and sulfates, as well as a set of variables that define the physical chemistry of the water-conductivity, temperature, TDS, and dissolved oxygen-transported by a channel from Poderosa mine affected by acid mine drainage, through the use of techniques of artificial intelligence: fuzzy logic and data mining. The sampling campaign was carried out in May of 2012. There were a total of 16 sites, the first inside the tunnel and the last at the mouth of the river Odiel, with a distance of approximately 10 m between each pair of measuring stations. While the tools of classical statistics, which are widely used in this context, prove useful for defining proximity ratios between variables based on Pearson's correlations, in addition to making it easier to handle large volumes of data and producing easier-to-understand graphs, the use of fuzzy logic tools and data mining results in better definition of the variations produced by external stimuli on the set of variables. This tool is adaptable and can be extrapolated to any system polluted by acid mine drainage using simple, intuitive reasoning.

Simulating Direct and Indirect Damages to Commercial Fisheries from Marine Sand Mining: A Case Study in Korea

NASA Astrophysics Data System (ADS)

Kim, Tae-Guon; Grigalunas, Thomas

2009-09-01

Rapid growth in marine sand mining for construction and other uses poses environmental challenges to coastal nations virtually worldwide. Yet the development of management policies, such as a system of fees imposed on operators for damage caused by mining, has been frustrated by a lack of studies to support such measures. Adapting a Beverton-Holt bioeconomic model, this paper attempts to contribute to the estimation of external costs to commercial fisheries due to marine mining. Using the major mining area of Ongjin in Korea as a case study, we estimate economic losses in use value of commercial fisheries through the time to recovery of the injured resource stocks. Present value of lost catch over a 1-year period from mining to resource recovery is estimated at 38,851 for a single “prototype” mining site. Estimated cumulative damages due to recurring mining for 5 and 10 years are 1.5 million and 2.2 million, respectively, at 20 mining sites. Sensitivity analyses are used to examine the effects of alternative assumptions to assess the many sources of uncertainty. Using a form of meta-analysis, dose-response information is used to assess the excess mortality the mining sediment plume has on eggs and larvae and, ultimately, on the value of lost catch (841). Also addressed is the importance of specifying the appropriate “premining” conditions against which to assess environmental losses at the mining site. Damages estimated with premining fish populations are 23,066 higher than is the case using postmining conditions. Overall, the illustrative results suggest the variety of complex conditions which influence damage to fisheries from mining and which can benefit from further study to improve management guidelines.

Numerical Study on 4-1 Coal Seam of Xiaoming Mine in Ascending Mining

PubMed Central

Tianwei, Lan; Hongwei, Zhang; Sheng, Li; Weihua, Song; Batugin, A. C.; Guoshui, Tang

2015-01-01

Coal seams ascending mining technology is very significant, since it influences the safety production and the liberation of dull coal, speeds up the construction of energy, improves the stability of stope, and reduces or avoids deep hard rock mining induced mine disaster. Combined with the Xiaoming ascending mining mine 4-1, by numerical calculation, the paper analyses ascending mining 4-1 factors, determines the feasibility of ascending mining 4-1 coalbed, and proposes roadway layout program about working face, which has broad economic and social benefits. PMID:25866840

Chemical Sensing for Buried Landmines - Fundamental Processes Influencing Trace Chemical Detection

DOE Office of Scientific and Technical Information (OSTI.GOV)

PHELAN, JAMES M.

2002-05-01

Mine detection dogs have a demonstrated capability to locate hidden objects by trace chemical detection. Because of this capability, demining activities frequently employ mine detection dogs to locate individual buried landmines or for area reduction. The conditions appropriate for use of mine detection dogs are only beginning to emerge through diligent research that combines dog selection/training, the environmental conditions that impact landmine signature chemical vapors, and vapor sensing performance capability and reliability. This report seeks to address the fundamental soil-chemical interactions, driven by local weather history, that influence the availability of chemical for trace chemical detection. The processes evaluated include:more » landmine chemical emissions to the soil, chemical distribution in soils, chemical degradation in soils, and weather and chemical transport in soils. Simulation modeling is presented as a method to evaluate the complex interdependencies among these various processes and to establish conditions appropriate for trace chemical detection. Results from chemical analyses on soil samples obtained adjacent to landmines are presented and demonstrate the ultra-trace nature of these residues. Lastly, initial measurements of the vapor sensing performance of mine detection dogs demonstrates the extreme sensitivity of dogs in sensing landmine signature chemicals; however, reliability at these ultra-trace vapor concentrations still needs to be determined. Through this compilation, additional work is suggested that will fill in data gaps to improve the utility of trace chemical detection.« less

Understanding processes affecting mineral deposits in humid environments

USGS Publications Warehouse

Seal, Robert R.; Ayuso, Robert A.

2011-01-01

Recent interdisciplinary studies by the U.S. Geological Survey have resulted in substantial progress toward understanding the influence that climate and hydrology have on the geochemical signatures of mineral deposits and the resulting mine wastes in the eastern United States. Specific areas of focus include the release, transport, and fate of acid, metals, and associated elements from inactive mines in temperate coastal areas and of metals from unmined mineral deposits in tropical to subtropical areas; the influence of climate, geology, and hydrology on remediation options for abandoned mines; and the application of radiogenic isotopes to uniquely apportion source contributions that distinguish natural from mining sources and extent of metal transport. The environmental effects of abandoned mines and unmined mineral deposits result from a complex interaction of a variety of chemical and physical factors. These include the geology of the mineral deposit, the hydrologic setting of the mineral deposit and associated mine wastes, the chemistry of waters interacting with the deposit and associated waste material, the engineering of a mine as it relates to the reactivity of mine wastes, and climate, which affects such factors as temperature and the amounts of precipitation and evapotranspiration; these factors, in turn, influence the environmental behavior of mineral deposits. The role of climate is becoming increasingly important in environmental investigations of mineral deposits because of the growing concerns about climate change.

Cognitive and Noncognitive Changes From Participation in National Guard Youth ChalleNGe

DTIC Science & Technology

2013-10-01

confidence and locus of control (belief that one’s actions influence eventual outcomes). By the end of the program, the measured noncognitive skills of...quite detailed; it includes eight core compo- nents: leadership/ followership , responsible citizenship, service to community, life-coping skills, physical... actions (versus random factors or other powers) deter- mine outcomes. Essentially, the scale measures the extent to which respondents believe that they

Outdoor (222)Rn-concentrations in Germany - part 2 - former mining areas.

PubMed

Kümmel, M; Dushe, C; Müller, S; Gehrcke, K

2014-06-01

In the German Federal States of Saxony, Saxony-Anhalt and Thuringia, centuries of mining and milling activities resulted in numerous residues with increased levels of natural radioactivity such as waste rock dumps and tailings ponds. These may have altered potential radiation exposures of the population significantly. Especially waste rock dumps from old mining activities as well as 20th century uranium mining may, due to their radon ((222)Rn) exhalation capacity, lead to significant radiation exposures. They often lie close to or within residential areas. In order to study the impact on the natural radon level, the Federal Office for Radiation Protection (BfS) has run networks of radon measurement points in 16 former mining areas, together with 2 networks in regions not influenced by mining for comparison purposes. Representative overviews of the long-term outdoor radon concentrations could be established including estimates of regional background concentrations. Former mining and milling activities did not result in large-area impacts on the outdoor radon level. However, significantly increased radon concentrations were observed in close vicinity of shafts and large waste rock dumps. They are partly located in residential areas and need to be considered under radiation protection aspects. Examples are given that illustrate the consequences of the Wismut Ltd. Company's reclamation activities on the radon situation. Copyright © 2014 Elsevier Ltd. All rights reserved.

Assessing the influence of compost and biochar amendments on the mobility and toxicity of metals and arsenic in a naturally contaminated mine soil.

PubMed

Beesley, Luke; Inneh, Onyeka S; Norton, Gareth J; Moreno-Jimenez, Eduardo; Pardo, Tania; Clemente, Rafael; Dawson, Julian J C

2014-03-01

Amending contaminated soils with organic wastes can influence trace element mobility and toxicity. Soluble concentrations of metals and arsenic were measured in pore water and aqueous soil extracts following the amendment of a heavily contaminated mine soil with compost and biochar (10% v:v) in a pot experiment. Speciation modelling and toxicity assays (Vibrio fischeri luminescence inhibition and Lolium perenne germination) were performed to discriminate mechanisms controlling metal mobility and assess toxicity risk thereafter. Biochar reduced free metal concentrations furthest but dissolved organic carbon primarily controlled metal mobility after compost amendment. Individually, both amendments induced considerable solubilisation of arsenic to pore water (>2500 μg l(-1)) related to pH and soluble phosphate but combining amendments most effectively reduced toxicity due to simultaneous reductions in extractable metals and increases in soluble nutrients (P). Thus the measure-monitor-model approach taken determined that combining the amendments was most effective at mitigating attendant toxicity risk. Copyright © 2013 Elsevier Ltd. All rights reserved.

[Features of health disorders in miners employed at northern copper-nickel mines].

PubMed

Siurin, S V; Shilov, V V

2016-01-01

The aim of the study was to assess the influence of different working conditions on the health of 1523 copper-nickel miners of the Kola High North. The low degree of mechanization of mining operations was established to be related to more higher levels of vibration, noise and physical overloads. The working in such conditions, when compared with high mining mechanization, leads to a decrease in the number of conditionally healthy workers (12% and 20.7%, p <0.001) an increase in the number of diseases in the one worker (2,94 ± 0,10 and 2.13 ± 0.07 cases, p <0,001), the increase of the risk of occupational diseases (OD) of the musculoskeletal (RR = 2.31) and nervous (RR = 2.07) systems, vibration disease (RR = 1.70), neuro-sensory hearing loss (RR = 1.90). Both at low and high degree of mechanization of mining operations the greatest risk of occupational diseases in noted in drifters (OR = 5.68), at that it was higher at hand mining than at mechanized mining (RR = 1.44). There was made a conclusion about the need to improve the complex of measures for the preservation of health in this group of workers, especially engaged in the performance of tunnel works.

Stress measurements in Kuzbass mines using photoelastic sensors

NASA Astrophysics Data System (ADS)

Schastlivtsev, E.

1996-06-01

The basic amount of known measurements of stressed state in front of development workings' faces was carried out with the use of hydraulic sensors, which give an information about principal stresses without their separation. Besides, the availability of pipe-line and cumbersome equipment make more complicated and sometimes impossible the process of stresses' measurements during works in mining process. In our opinion, the borehole and photoelastic sensors at high degree satisfy with the conditions of stresses' measurements in front of mining workings' faces. The principal idea of the method is in the usage of proper face advancing aiming the estimation of the field stresses in its neighborhood. Borehole and photoelastic sensors, fixed in the advanced boreholes, drilled from the active face react to the field change of stresses or deformation caused by working face advancing. While obtaining this information we may judge about the distribution of additional stresses in rock of face's neighborhood and concentration of stresses in front of face. The usage of cavity (because of face advancing) in the quality of disturbing influence in combination with the properties of ring photoelastic sensor to given an information about magnitude and direction of secondary principle stresses, permits us to obtain rather a simple and not labor consuming method of investigation of field additional stresses in the working's face neighborhood.

Roof instability characteristics and pre-grouting of the roof caving zone in residual coal mining

NASA Astrophysics Data System (ADS)

Zhao, Tong; Liu, Changyou

2017-12-01

Abandoned roadways and roof caving zones are commonly found in residual coal, and can destroy the integrity of the coal seam and roof. Resulting from mining-induced stress, continuous collapse and fracture instability in roof caving zones (RCZs) jeopardize the safety and efficiency of residual coal mining. Based on the engineering geology conditions of remining face 3101 in Shenghua Mine, the roof fracture and instability features of the RCZ were analyzed through physical simulation, theoretical analysis, and field measurements. In this case, influenced by the RCZ, the main roof across the RCZ fractured and rotated towards the goaf, greatly increasing the working resistance, and crushing the supports. The sudden instability of the coal pillars weakened its support of the main roof, thus resulting in long-key blocks across the RCZ and hinged roof structures, which significantly decreased the stability of the underlying immediate roof. This study establishes a mechanical model for the interactions between the surrounding rock and the supports in the RCZ, determines the reasonable working resistance, and examines the use of pre-grouting solidification restoration technology (PSRT) to solidify the RCZ and reinforce the coal pillars—thus increasing their bearing capacity. Field measurements revealed no roof flaking, inhomogeneous loading or support crushing, indicating that the PSRT effectively controlled the surrounding rock of the RCZ.

The effect of cap lamp lighting on postural control and stability

PubMed Central

Sammarco, John J.; Pollard, Jonisha P.; Porter, William L.; Dempsey, Patrick G.; Moore, Caitlin T.

2015-01-01

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are conducting mine illumination research with the objective of improving miner safety. Slips, trips, and falls (STFs) are the second leading accident class (18.1%, n = 2,374) of nonfatal lost-time injuries at underground mines (MSHA, 2005–2009). Factors contributing to STFs include recognition of hazards as well as postural balance and age. Improved lighting may enable better hazard recognition and reduce the impact of postural balance and age. Previous research has shown that cap lamp technology that used light-emitting diodes (LEDs) has improved hazard detection. This study was an initial investigation to determine if cap lamp lighting significantly influences measures of static postural stability (displacement and velocity of center of pressure). Results of this investigation showed no significant differences in the balance measures of interest between cap lamps tested. However, balance was shown to significantly decline (p < 0.05) when tested in an underground coal mine compared to the laboratory testing condition. Relevance to industry: Underground coal mine workers wear cap lamps on their hard hats as their primary light source to illuminate nearby areas where their vision is directed. Proper illumination may improve miner safety by improving their STF hazard recognition and balance. PMID:26472917

Soil and vegetation influence in plants natural radionuclides uptake at a uranium mining site

NASA Astrophysics Data System (ADS)

Charro, E.; Moyano, A.

2017-12-01

The main objective of this work is to investigate the uptake of several radionuclides by the vegetation characteristic of a dehesa ecosystem in uranium mining-impacted soils in Central-West of Spain. The activity concentration for 238U, 226Ra, 210Pb, 232Th, and 224Ra was measured in soil and vegetation samples using a Canberra n-type HPGe gamma-ray spectrometer. Transfer factors of natural radionuclides in different tissues (leaves, branches, twigs, and others) of native plants were evaluated. From these data, the influence of the mine, the physicochemical parameters of the soils and the type of vegetation were analyzed in order to explain the accumulation of radionuclides in the vegetation. A preferential uptake of 210Pb and 226Ra by plants, particularly by trees of the Quercus species (Quercus pyrenaica and Quercus ilex rotundifolia), has been observed, being the transfer factors for 226Ra and 210Pb in these tree species higher than those for other plants (like Pinus pinaster, Rubur ulmifolius and Populus sp.). The analysis of radionuclide contents and transfer factors in the vegetation showed no evidence of influence of the radionuclide concentration in soils, although it could be explained in terms of the type of plants and, in particular, of the tree's species, with special attention to the tree's rate of growth, being higher in slow growing species.

INFLUENCE OF PH AND OXIDATION-REDUCTION (EH) POTENTIAL ON THE DISSOLUTION OF MERCURY-CONTAINING MINE WASTES FROM THE SULFUR BANK MERCURY MINE

EPA Science Inventory

Mine waste rock and roaster tailings were collected from the Sulfur Bank Mercury Mine (SBMM) located in Clearlake Oaks, California. The site has been under investigation as a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) site. Characterization an...

The influence of regional geological settings on the seismic hazard level in copper mines in the Legnica-Głogów Copper Belt Area (Poland)

NASA Astrophysics Data System (ADS)

Burtan, Zbigniew

2017-11-01

The current level of rockburst hazard in copper mines of the (LGOM) Legnica- Głogów Copper Belt Area is mostly the consequence of mining-induced seismicity, whilst the majority of rockbursting events registered to date were caused by high-energy tremors. The analysis of seismic readings in recent years reveals that the highest seismic activity among the copper mines in the LGOM is registered in the mine Rudna. This study investigates the seismic activity in the rock strata in the Rudna mine fields over the years 2006-2015. Of particular interest are the key seismicity parameters: the number of registered seismic events, the total energy emissions, the energy index. It appears that varied seismic activity in the area may be the function of several variables: effective mining thickness, the thickness of burst-prone strata and tectonic intensity. The results support and corroborate the view that principal factors influencing the actual seismic hazard level are regional geological conditions in the copper mines within the Legnica-Głogów Copper Belt Area.

Windblown Dust Deposition Forecasting and Spread of Contamination around Mine Tailings.

PubMed

Stovern, Michael; Guzmán, Héctor; Rine, Kyle P; Felix, Omar; King, Matthew; Ela, Wendell P; Betterton, Eric A; Sáez, Avelino Eduardo

2016-02-01

Wind erosion, transport and deposition of windblown dust from anthropogenic sources, such as mine tailings impoundments, can have significant effects on the surrounding environment. The lack of vegetation and the vertical protrusion of the mine tailings above the neighboring terrain make the tailings susceptible to wind erosion. Modeling the erosion, transport and deposition of particulate matter from mine tailings is a challenge for many reasons, including heterogeneity of the soil surface, vegetative canopy coverage, dynamic meteorological conditions and topographic influences. In this work, a previously developed Deposition Forecasting Model (DFM) that is specifically designed to model the transport of particulate matter from mine tailings impoundments is verified using dust collection and topsoil measurements. The DFM is initialized using data from an operational Weather Research and Forecasting (WRF) model. The forecast deposition patterns are compared to dust collected by inverted-disc samplers and determined through gravimetric, chemical composition and lead isotopic analysis. The DFM is capable of predicting dust deposition patterns from the tailings impoundment to the surrounding area. The methodology and approach employed in this work can be generalized to other contaminated sites from which dust transport to the local environment can be assessed as a potential route for human exposure.

Windblown Dust Deposition Forecasting and Spread of Contamination around Mine Tailings

PubMed Central

Stovern, Michael; Guzmán, Héctor; Rine, Kyle P.; Felix, Omar; King, Matthew; Ela, Wendell P.; Betterton, Eric A.; Sáez, Avelino Eduardo

2017-01-01

Wind erosion, transport and deposition of windblown dust from anthropogenic sources, such as mine tailings impoundments, can have significant effects on the surrounding environment. The lack of vegetation and the vertical protrusion of the mine tailings above the neighboring terrain make the tailings susceptible to wind erosion. Modeling the erosion, transport and deposition of particulate matter from mine tailings is a challenge for many reasons, including heterogeneity of the soil surface, vegetative canopy coverage, dynamic meteorological conditions and topographic influences. In this work, a previously developed Deposition Forecasting Model (DFM) that is specifically designed to model the transport of particulate matter from mine tailings impoundments is verified using dust collection and topsoil measurements. The DFM is initialized using data from an operational Weather Research and Forecasting (WRF) model. The forecast deposition patterns are compared to dust collected by inverted-disc samplers and determined through gravimetric, chemical composition and lead isotopic analysis. The DFM is capable of predicting dust deposition patterns from the tailings impoundment to the surrounding area. The methodology and approach employed in this work can be generalized to other contaminated sites from which dust transport to the local environment can be assessed as a potential route for human exposure. PMID:29082035

A case study of methane gas migration through sealed mine GOB into active mine workings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garcia, F.; McCall, F.E.; Trevits, M.A.

1995-12-31

The U.S. Bureau of Mines investigated the influence of atmospheric pressure changes on methane gas migration through mine seals at a mine site located in the Pittsburgh Coalbed. The mine gained access to a coal reserve through part of an abandoned mine and constructed nine seals to isolate the extensive old workings from the active mine area. Underground problems were experienced when atmospheric pressure fell, causing methane gas to migrate around the seals and into the active workings. During mining operations, methane gas levels exceeded legal limits and coal production was halted until the ventilation system could be improved. Whenmore » mining resumed with increased air flow, methane gas concentrations occasionally exceeded the legal limits and production had to be halted until the methane level fell within the mandated limit. To assist the ventilation system, a pressure relief borehole located in the abandoned workings near the mine seals was proposed. Preliminary estimates by a gob gas simulator (computer model) suggested that a 0.76 m (2.5 ft) diameter pressure relief borehole with an exhaust fan would be necessary to remove enough methane from the abandoned area so that the ventilation system could dilute the gas in the active workings. However, by monitoring methane gas emissions and seal pressure, during periods of low atmospheric pressure, the amount of methane gas that migrated into the active mine workings was calculated. Researchers then determined that a relief borehole, 20.3 cm (8-in) with an exhaust fan could remove at least twice the maximum measured volume of migrating methane gas. Because gas concentrations in the abandoned workings could potentially reach explosive limits, it was proposed that the mine eliminate the exhaust fan. Installation of the recommended borehole and enlarging two other ventilation boreholes located In the abandoned area reduced methane gas leakage through the seals by at least 63%.« less

Mine wastes and human health

USGS Publications Warehouse

Plumlee, Geoffrey S.; Morman, Suzette A.

2011-01-01

Historical mining and mineral processing have been linked definitively to health problems resulting from occupational and environmental exposures to mine wastes. Modern mining and processing methods, when properly designed and implemented, prevent or greatly reduce potential environmental health impacts. However, particularly in developing countries, there are examples of health problems linked to recent mining. In other cases, recent mining has been blamed for health problems but no clear links have been found. The types and abundances of potential toxicants in mine wastes are predictably influenced by the geologic characteristics of the deposit being mined. Hence, Earth scientists can help understand, anticipate, and mitigate potential health issues associated with mining and mineral processing.

The Evaluation of a Risk Degree for the Process of a Brown Coal Spontaneous Ignition on Dumps with Using of Modern Numeric Methods

NASA Astrophysics Data System (ADS)

Klouda, Petr; Moni, Vlastimil; Řehoř, Michal; Blata, Jan; Helebrant, František

2018-06-01

The article is a summary of information about evaluation of a risk degree for a brown coal spontaneous ignition which is realized on the base of a database analysis of information about the development of stative quantities and desorbated gases in the stored bodies of the brown coal. The data were gained from the long term complex measurements which were realized at chosen companies during the coal mining in the previous parts of the project. In the last part of the project, we examined results of temperature models from thermographs with results of gasses and coal samples from the mines. Then, the influence of atmospheric conditions (insolation, water downfall, changes of barometric pressure etc.), the influence of coal mass degradation, the influence of physical and chemical factors, and the influence of other defective factors on the process of the coal spontaneous ignition. The gasmetry was assess with gas in-situ samples and laboratory gas models of indicative gasses for the spontaneous ignition, which were taken from the method of the thermic oxidation with the aim of the correlation finding for an epicentre of temperature within the spontaneous ignition.

EVALUATION OF A TWO-STAGE PASSIVE TREATMENT APPROACH FOR MINING INFLUENCE WATERS

EPA Science Inventory

A two-stage passive treatment approach was assessed at bench-scale using two Colorado Mining Influenced Waters (MIWs). The first-stage was a limestone drain with the purpose of removing iron and aluminum and mitigating the potential effects of mineral acidity. The second stage w...

EPA ORD's Role In Mine-Influenced Water-Treatment: Past, Present and Future

EPA Science Inventory

The purpose of this presentation is to describe the different technologies that the Office of Research and Development (ORD) of the U.S. Environmental Protection Agency has tested on bench, field and pilot studies on mine-influenced water. Each of these technologies has been dem...

Repair and Protection of Small Railway Viaduct with Jammed Span at the Mining Influence

NASA Astrophysics Data System (ADS)

Bętkowski, Piotr

2017-10-01

This paper is about the maintenance of bridge objects on mining areas. Based on several years of observation is shown as functional parameters and technical conditions were deteriorated. As a result of the mining area deformations appeared among others following damages: block of bearings, jam of span, cracks on the abutments. The article describes series of clever maintenance repairs (such as the restoration of displacement freedom on non-standard tangent bearings) which enabled the exploitation of the viaduct without interruptions of railway communication. The region of the bridge is planned to further mining activities, which prejudged, that a repair of the viaduct was necessary to realization. The article discusses the predicted mining area deformation and analyses their influence on the bridge structure. Repair of the viaduct is a comprehensive example of the mining facility protection with the restoration of the expansion joints, bearings replacement, widening benches under bearings, stitching cracks and strengthening abutments, recreating the isolation and the drainage system damaged by mining influences, performance strut in the foundation level. An important element in determining the durability of repair is the selection of appropriate materials and repair technology, which is analysed in the article. All of these tasks completed in less than four months. Article illustrates the photo documentation made before and after repairs and technical drawings that show the range of the repairs.

Influence of gravel mining and other factors on detection probabilities of Coastal Plain fishes in the Mobile River Basin, Alabama

USGS Publications Warehouse

Hayer, C.-A.; Irwin, E.R.

2008-01-01

We used an information-theoretic approach to examine the variation in detection probabilities for 87 Piedmont and Coastal Plain fishes in relation to instream gravel mining in four Alabama streams of the Mobile River drainage. Biotic and abiotic variables were also included in candidate models. Detection probabilities were heterogeneous across species and varied with habitat type, stream, season, and water quality. Instream gravel mining influenced the variation in detection probabilities for 38% of the species collected, probably because it led to habitat loss and increased sedimentation. Higher detection probabilities were apparent at unmined sites than at mined sites for 78% of the species for which gravel mining was shown to influence detection probabilities, indicating potential negative impacts to these species. Physical and chemical attributes also explained the variation in detection probabilities for many species. These results indicate that anthropogenic impacts can affect detection probabilities for fishes, and such variation should be considered when developing monitoring programs or routine sampling protocols. ?? Copyright by the American Fisheries Society 2008.

Hydrochemical evaluation of the influences of mining activities on river water chemistry in central northern Mongolia.

PubMed

Batsaikhan, Bayartungalag; Kwon, Jang-Soon; Kim, Kyoung-Ho; Lee, Young-Joon; Lee, Jeong-Ho; Badarch, Mendbayar; Yun, Seong-Taek

2017-01-01

Although metallic mineral resources are most important in the economy of Mongolia, mining activities with improper management may result in the pollution of stream waters, posing a threat to aquatic ecosystems and humans. In this study, aiming to evaluate potential impacts of metallic mining activities on the quality of a transboundary river (Selenge) in central northern Mongolia, we performed hydrochemical investigations of rivers (Tuul, Khangal, Orkhon, Haraa, and Selenge). Hydrochemical analysis of river waters indicates that, while major dissolved ions originate from natural weathering (especially, dissolution of carbonate minerals) within watersheds, they are also influenced by mining activities. The water quality problem arising from very high turbidity is one of the major environmental concerns and is caused by suspended particles (mainly, sediment and soil particles) from diverse erosion processes, including erosion of river banks along the meandering river system, erosion of soils owing to overgrazing by livestock, and erosion by human activities, such as mining and agriculture. In particular, after passing through the Zaamar gold mining area, due to the disturbance of sediments and soils by placer gold mining, the Tuul River water becomes very turbid (up to 742 Nephelometric Turbidity Unit (NTU)). The Zaamar area is also the contamination source of the Tuul and Orkhon rivers by Al, Fe, and Mn, especially during the mining season. The hydrochemistry of the Khangal River is influenced by heavy metal (especially, Mn, Al, Cd, and As)-loaded mine drainage that originates from a huge tailing dam of the Erdenet porphyry Cu-Mo mine, as evidenced by δ 34 S values of dissolved sulfate (0.2 to 3.8 ‰). These two contaminated rivers (Tuul and Khangal) merge into the Orkhon River that flows to the Selenge River near the boundary between Mongolia and Russia and then eventually flows into Lake Baikal. Because water quality problems due to mining can be critical, mining activities in central northern Mongolia should be carefully managed to minimize the transboundary movement of aquatic contaminants (in particular, turbidity, dissolved organic carbon, Fe and Al) from mining activities.

30 CFR 72.800 - Single, full-shift measurement of respirable coal mine dust.

Code of Federal Regulations, 2014 CFR

2014-07-01

... coal mine dust. 72.800 Section 72.800 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH HEALTH STANDARDS FOR COAL MINES Miscellaneous § 72.800 Single, full-shift measurement of respirable coal mine dust. The Secretary will use a single, full-shift...

Detection of induced seismicity effects on ground surface using data from Sentinel 1A/1B satellites

NASA Astrophysics Data System (ADS)

Milczarek, W.

2017-12-01

Induced seismicity is the result of human activity and manifests itself in the form of shock and vibration of the ground surface. One of the most common factors causing the occurrence of induced shocks is underground mining activity. Sufficiently strong high-energy shocks may cause displacements of the ground surface. This type of shocks can have a significant impact on buildings and infrastructure. Assessment of the size and influence of induced seismicity on the ground surface is one of the major problems associated with mining activity. In Poland (Central Eastern Europe) induced seismicity occurs in the area of hard coal mining in the Upper Silesian Coal Basin and in the area of the Legnica - Głogów Copper Basin.The study presents an assessment of the use of satellite radar data (SAR) for the detection influence of induced seismicity in mining regions. Selected induced shocks from the period 2015- 2017 which occurred in the Upper Silesian Coal Basin and the Legnica - Głogów Copper Basin areas have been analyzed. In the calculations SAR data from the Sentinel 1A and Sentinel 1B satellites have been used. The results indicate the possibility of quickly and accurate detection of ground surface displacements after an induced shock. The results of SAR data processing were compared with the results from geodetic measurements. It has been shown that SAR data can be used to detect ground surface displacements on the relative small regions.

The Relationship between Elemental Carbon and Diesel Particulate Matter in Underground Metal/Nonmetal Mines in the United States and Coal Mines in Australia

PubMed Central

Noll, James; Gilles, Stewart; Wu, Hsin Wei; Rubinstein, Elaine

2015-01-01

In the United States, total carbon (TC) is used as a surrogate for determining diesel particulate matter (DPM) compliance exposures in underground metal/nonmetal mines. Since TC can be affected by interferences and elemental carbon (EC) is not, one method used to estimate the TC concentration is to multiply the EC concentration from the personal sample by a conversion factor to avoid the influence of potential interferences. Since there is no accepted single conversion factor for all metal/nonmetal mines, one is determined every time an exposure sample is taken by collecting an area sample that represents the TC/EC ratio in the miner's breathing zone and is away from potential interferences. As an alternative to this procedure, this article investigates the relationship between TC and EC from DPM samples to determine if a single conversion factor can be used for all metal/nonmetal mines. In addition, this article also investigates how well EC represents DPM concentrations in Australian coal mines since the recommended exposure limit for DPM in Australia is an EC value. When TC was predicted from EC values using a single conversion factor of 1.27 in 14 US metal/nonmetal mines, 95% of the predicted values were within 18% of the measured value, even at the permissible exposure limit (PEL) concentration of 160 μg/m3 TC. A strong correlation between TC and EC was also found in nine underground coal mines in Australia. PMID:25380085

Production Quality, Value and Revenue in Polish Copper Mines

NASA Astrophysics Data System (ADS)

Malewski, Jerzy

2016-10-01

Polish copper ore deposits, located in the Legnica-Głogów Copper District (LGOM) documented an area of over 200 km2, at a depth of 600-1400 meters. The estimated resources equal to 22.7 million tonnes of copper (proven and probable), or 44.4 million t (measured and indicated), or 8.7 million t (infered), at the criterion of profitability at a cost less than 50 cents per ton of ore. Organization of production takes place in the combine of mining and metallurgy (KGHM). Ore is extracted in three mines: Lubin, Polkowice-Sieroszowice and Rudna. The total production of these mines is about 31 million tonnes/year of ore, from which it receives a 576000 t/y of copper, 1152 t/y of silver, 1066 kg/y of gold, and certain amounts of Pb, Zn, Se, Re, Ni, SO4, H2SO4. The quality (grading) of the ore in exploited deposits is varied, affecting the quality and quantity of produced concentrates, what influence on its market value. The paper presents a brief description of ore deposit and estimates mines revenues and production profit. Calculations show that at today's (June 2016) metal prices each of the mine can expect the following net smelter revenue: Lubin ∼⃒41, P-S ∼⃒70, Rudna ∼⃒75 /t of ore. But estimated cost production differs less, i.e.: 45, 56 and 65/t of ore respectively, because of mining depth.

The Influence of Surface Coal Mining on Runoff Processes and Stream Chemistry in the Elk Valley, British Colubmbia, Canada

NASA Astrophysics Data System (ADS)

Carey, S. K.; Wellen, C. C.; Shatilla, N. J.

2015-12-01

Surface mining is a common method of accessing coal. In high-elevation environments, vegetation and soils are typically removed prior to the blasting of overburden rock, thereby allowing access to mineable ore. Following this, the removed overburden rock is deposited in adjacent valleys as waste rock spoils. Previous research has identified that areas downstream of surface coal mining have impaired water quality, yet there is limited information about the interaction of hydrology and geochemistry across a range of mining conditions, particularly at the headwater scale. Here, we provide an analysis of an extensive long-term data set of geochemistry and flows across a gradient of coal mining in the Elk Valley, British Columbia, Canada. This work is part of a broader R&D program examining the influence of surface coal mining on hydrological and water quality responses in the Elk Valley aimed at informing effective management responses. Results indicate that water from waste rock piles has an ionic profile distinct from unimpacted catchments. While the concentration of geochemicals increased with the degree of mine impact, the control of hydrological transport capacity over geochemical export did not vary with degree of mine impact. Geochemical export in mine-influenced catchments was limited more strongly by transport capacity than supply, implying that more water moving through the waste rock mobilized more geochemicals. Placement of waste rock within the catchment (headwaters or outlet) did not affect chemical concentrations but did alter the timing with which chemically distinct water mixed. This work advances on results reported earlier using empirical models of selenium loading and further highlights the importance of limiting water inputs into waste rock piles.

The Necessity of Public Relations for Sustainable Mining Activities

NASA Astrophysics Data System (ADS)

Lee, Hyunbock; Ji, Sangwoo

2015-04-01

This paper reports research about the necessity of image making for sustainable mine developments in the Republic of Korea. One of the big risks in mining activities is mining area residents opposing mine developments and operations. Analysis of the media reports on disputes between mining companies and residents can determine causes of opposing mine developments, dispute process, and influences of disputes on processes of mining projects. To do this, civil complaints from 2009 to 2012 and 24 media reports since 2000 on opposing mining activities are analyzed. And, to analyze difficulties of mining companies, the survey is conducted to target to mining companies. 57 representatives of mining companies are participated in the survey. The result of analysis cited that the major reasons of anti-mining activities are environmental degradation and reduced agricultural productivity. And specifically because of water pollution (50%), crop damages (33%), and mining dust pollution (21%), communities of mining area are against mine developments and operations. However, 25% of residents have experience of the damage caused by mining activities and the remaining 75% of residents opposing mining activities simply have anxiety about mining pollution. In the past, construction-oriented, environment-unfriendly mining projects had lasted. And while mine reclamation had been postponed in abandoned mines, mining area residents had suffered from mining pollution. So, mining area residents are highly influenced by the prejudice that mining activities are harmful to mining area communities. Current mining projects in South Korea, unlike the past mining activity, focus on minimizing environmental damage and contributing to mining area communities financially. But, in many case of disputes between mining companies and mining area residents, the both cannot reach an agreements because of the negative prejudice. Moreover, some communities categorically refuse any mining activity. On the other hand, in the survey to determine what the greatest difficulties of the current mining activities, 54% of mining companies chose environmental regulations, 26% of mining companies chose conflicts between mine area residents and mining companies. Environmental regulations are may defined as the greatest difficulty of current mining activities. But most of environmental regulation's problems are caused by frictions with residents, because all of South Korean mines are very close to villages. So, the biggest difficulty of mining activities can be defined conflicts between residents and mining companies. Moreover, general people in South Korea including some mining engineers recognize the mining industry as a declined and pollution industry. Without clear understanding of mining activities, any mine developments and policies related to mining activities cannot be made by rational discussions. And, if their recognition is not formed in a rational way, it will be turned to extreme fear or blind hatred. Therefore, to understand mining activities correctly, the effective public relations strategy is necessary such as corporate advertisements or public advertisements.

Influence of high-power nonlinear consumers on electric energy losses in mining high-voltage power line

NASA Astrophysics Data System (ADS)

Averbukh, M. A.; Prasol, D. A.

2018-03-01

The article elucidates the influence of high-power nonlinear consumers on electric energy losses in a mining high-voltage power line. The object of the study was a fragment of a power supply system of a mining enterprise with hoists. The investigation has assessed the electric energy losses conditioned by nonsinusoidal currents and voltages of the power line over a single hoist operation cycle. Also, the total electric energy losses in a high-voltage power line of a mining enterprise was calculated. The energy losses due to nonsinusoidal currents and voltages over single operation cycle of the cage hoist amount to 36.358 kWh. The presence of such losses increases total technological power and energy losses in the mining high-voltage power line by approximately 5-15%. The total energy losses in the components of the mining enterprise high-voltage power line caused by nonsinusoidal voltage are significant and lead to additional expenses of the company.

Effect Of Organic Substrate Composition On Microbial Community Structure Of Pilot-Scale Biochemical Reactors Treating Mining Influenced Water

EPA Science Inventory

Mining-influenced water (MIW) is acidic, metal rich water formed when sulfide minerals react with oxygen and water. There are various options for the treatment of MIW; however, passive biological systems such as biochemical reactors (BCRs) have shown promise because of their low...

Effect Of Organic Substrate Composition On Microbial Community Structure Of Pilot-Scale Biochemical Reactors Treating Mining Influenced Water - (Presentation)

EPA Science Inventory

Mining-influenced water (MIW) is acidic, metal rich water formed when sulfide minerals react with oxygen and water. There are various options for the treatment of MIW; however, passive biological systems such as biochemical reactors (BCRs) have shown promise because of their low...

Geochemical Analyses of Surface and Shallow Gas Flux and Composition Over a Proposed Carbon Sequestration Site in Eastern Kentucky

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas Parris; Michael Solis; Kathryn Takacs

2009-12-31

Using soil gas chemistry to detect leakage from underground reservoirs (i.e. microseepage) requires that the natural range of soil gas flux and chemistry be fully characterized. To meet this need, soil gas flux (CO{sub 2}, CH{sub 4}) and the bulk (CO{sub 2}, CH{sub 4}) and isotopic chemistry ({delta}{sup 13}C-CO2) of shallow soil gases (<1 m, 3.3 ft) were measured at 25 locations distributed among two active oil and gas fields, an active strip mine, and a relatively undisturbed research forest in eastern Kentucky. The measurements apportion the biologic, atmospheric, and geologic influences on soil gas composition under varying degrees ofmore » human surface disturbance. The measurements also highlight potential challenges in using soil gas chemistry as a monitoring tool where the surface cover consists of reclaimed mine land or is underlain by shallow coals. For example, enrichment of ({delta}{sup 13}C-CO2) and high CH{sub 4} concentrations in soils have been historically used as indicators of microseepage, but in the reclaimed mine lands similar soil chemistry characteristics likely result from dissolution of carbonate cement in siliciclastic clasts having {delta}{sup 13}C values close to 0{per_thousand} and degassing of coal fragments. The gases accumulate in the reclaimed mine land soils because intense compaction reduces soil permeability, thereby impeding equilibration with the atmosphere. Consequently, the reclaimed mine lands provide a false microseepage anomaly. Further potential challenges arise from low permeability zones associated with compacted soils in reclaimed mine lands and shallow coals in undisturbed areas that might impede upward gas migration. To investigate the effect of these materials on gas migration and composition, four 10 m (33 ft) deep monitoring wells were drilled in reclaimed mine material and in undisturbed soils with and without coals. The wells, configured with sampling zones at discrete intervals, show the persistence of some of the aforementioned anomalies at depth. Moreover, high CO{sub 2} concentrations associated with coals in the vadose zone suggest a strong affinity for adsorbing CO{sub 2}. Overall, the low permeability of reclaimed mine lands and coals and CO2 adsorption by the latter is likely to reduce the ability of surface geochemistry tools to detect a microseepage signal.« less

Influence of Geological Structure on Coal and Gas Outburst Occurrences in Turkish Underground Coal Mines

NASA Astrophysics Data System (ADS)

Esen, Olgun; Özer, Samet Can; Fişne, Abdullah

2015-04-01

Coal and gas outbursts are sudden and violent releases of gas and in company with coal that result from a complex function of geology, stress regime with gas pressure and gas content of the coal seam. The phenomena is referred to as instantaneous outbursts and have occurred in virtually all the major coal producing countries and have been the cause of major disasters in the world mining industry. All structures from faults to joints and cleats may supply gas or lead to it draining away. Most geological structures influence the way in which gas can drain within coal seams. From among all the geological factors two groups can be distinguished: parameters characterising directly the occurrence and geometry of the coal seams; parameters characterising the tectonic disturbances of the coal seams and neighbouring rocks. Also dykes may act as gas barriers. When the production of the coal seam is advanced in mine working areas, these barriers are failed mostly in the weak and mylonitized zones. Geology also plays a very important role in the outburst process. Coal seams of complex geological structure including faults, folds, and fractured rocks are liable to outbursts if coal seams and neighbouring rocks have high gas content level. The purpose of the study is to enlighten the coal industry in Turkey to improving mine safety in underground coal production and decrease of coal and gas outburst events due to increasing depth of mining process. In Turkey; the years between 1969 and 2013, the number of 90 coal and gas outbursts took place in Zonguldak Hard Coal Basin in both Kozlu and Karadon Collieries. In this study the liability to coal and gas outburst of the coal seams are investigated by measuring the strength of coal and the rock pressure. The correlation between these measurements and the event locations shows that the geological structures resulted in 52 events out of 90 events; 19 events close to the fault zones, 25 events thorough the fault zones and 8 events in the zones where sudden changes of inclination and/or thickness of the coal seam.

Assessing the effects of underground mining activities on high-voltage overhead power lines

NASA Astrophysics Data System (ADS)

Gusev, Vladimir; Zhuravlyov, Alexei; Maliukhina, Elena

2017-11-01

This paper introduces a technique for predictive assessment of changes in the position of power transmission towers and condition of overhead power lines, located in the zone of influence of displacements and deformations of the Earth's surface caused by mining activities. A special approach for monitoring the technical condition of towers and cables is proposed. It is intended to address the issue of controlling the condition of transmission lines that are under the influence of underground mining activities and to checkmate such impact.

Treatment Of Metal-Mine Effluents By Limestone Neutralization And Calcite Co-Precipitation

EPA Science Inventory

The U.S. Geological Survey - Leetown Science Center and the Colorado School of Mines have developed a remediation process for the treatment of metals in circumneutral mining influenced waters. The process involves treatment with a pulsed limestone bed (PLB) system, followed by c...

Effect Of Imposed Anaerobic Conditions On Metals Release From Acid-Mine Drainage Contaminated Streambed Sediments

EPA Science Inventory

Remediation of streams influenced by mine-drainage may require removal and burial of metal-containing bed sediments. Burial of aerobic sediments into an anaerobic environment may release metals, such as through reductive dissolution of metal oxyhydroxides. Mining-impacted aerob...

Distribution of biota in a stream polluted by acid mine-drainage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Warner, R.W.

1971-01-01

Acidic water draining from coal mines has severly restricted the diversity of biota inhabiting Roaring Creek, eastern West Virginia. Polluted reaches of the stream (median pH values ranging from 2.8 to 3.8) were inhabited by 3 to 12 genera of bottom-dwelling invertebrates and 10 to 19 species of periphytic algae. Invertebrates tolerant of the pollution included Sialis sp., chironomus plumosus and other Chironomidae, dytiscid beetles, and Ptilostomis sp. Predominant among the tolerant periphyton were Ulothrix tenerrima, Pinnularia termitina, Eunotia exigua, and Euglena mutabilis. Six other species of algae were tolerant of the acid mine-pollution, but were never numerous. Sections ofmore » Roaring Creek not severely polluted by acid drainage (pH medians of 4.5 or higher) supported diverse communities of 25 or more kinds of benthic animals and 27 or more species of periphytic algae. These stream reaches were inhibited by blackflies, crayfish, mayflies, stoneflies, and many species of caddisflies; these forms did not inhabit the more acidic stream reaches. Because of the complex and varying chemical composition of the acid mine-drainage, and also because of possible physical influences, measurements of pH values in the stream seemed to provide the most reliable, as well as unique, index of the effects of acid mine-drainage on aquatic life.« less

Northern bobwhite breeding season ecology on a reclaimed surface mine

USGS Publications Warehouse

Brooke, Jarred M.; Tanner, Evan P.; Peters, David C.; Tanner, Ashley M.; Harper, Craig A.; Keyser, Patrick D.; Clark, Joseph D.; Morgan, John J.

2017-01-01

Surface coal mining and subsequent reclamation of surface mines have converted large forest areas into early successional vegetative communities in the eastern United States. This reclamation can provide a novel opportunity to conserve northern bobwhite (Colinus virginianus). We evaluated the influence of habitat management activities on nest survival, nest-site selection, and brood resource selection on managed and unmanaged units of a reclaimed surface mine, Peabody Wildlife Management Area (Peabody), in west-central Kentucky, USA, from 2010 to 2013. We compared resource selection, using discrete-choice analysis, and nest survival, using the nest survival model in Program MARK, between managed and unmanaged units of Peabody at 2 spatial scales: the composition and configuration of vegetation types (i.e., macrohabitat) and vegetation characteristics at nest sites and brood locations (i.e., microhabitat). On managed sites, we also investigated resource selection relative to a number of different treatments (e.g., herbicide, disking, prescribed fire). We found no evidence that nest-site selection was influenced by macrohabitat variables, but bobwhite selected nest sites in areas with greater litter depth than was available at random sites. On managed units, bobwhite were more likely to nest where herbicide was applied to reduce sericea lespedeza (Lespedeza cuneata) compared with areas untreated with herbicide. Daily nest survival was not influenced by habitat characteristics or by habitat management but was influenced by nest age and the interaction of nest initiation date and nest age. Daily nest survival was greater for older nests occurring early in the breeding season (0.99, SE < 0.01) but was lower for older nests occurring later in the season (0.08, SE = 0.13). Brood resource selection was not influenced by macrohabitat or microhabitat variables we measured, but broods on managed units selected areas treated with herbicide to control sericea lespedeza and were located closer to firebreaks and disked native-warm season grass stands than would be expected at random. Our results suggest the vegetation at Peabody was sufficient without manipulation to support nesting and brood-rearing northern bobwhite at a low level, but habitat management practices improved vegetation for nesting and brood-rearing resource selection. Reproductive rates (e.g., nest survival and re-nesting rates) at Peabody were lower than reported in other studies, which may be related to nutritional deficiencies caused by the abundance of sericea lespedeza. On reclaimed mine lands dominated by sericea lespedeza, we suggest continuing practices such as disking and herbicide application that are targeted at reducing sericea lespedeza to improve the vegetation for nesting and brood-rearing bobwhite.

Treatment Of Metal-Mine Effluents By Limestone Neutralization And Calcite Co-Precipitation (Presentation)

EPA Science Inventory

The U.S. Geological Survey - Leetown Science Center and the Colorado School of Mines have developed a remediation process for the treatment of metals in circumneutral mining influenced waters. The process involves treatment with a pulsed limestone bed (PLB) system, followed by c...

Definition of Static Voltage Characteristics of the Motor Load for the Purpose of Increase in Energy Efficiency of Coal Mines of Kuzbass

NASA Astrophysics Data System (ADS)

Nepsha, Fedor; Efremenko, Vladimir

2017-11-01

The task of determining the static load characteristics is one of the most important tasks, the solution of which is necessary for the correct development of measures to increase the energy efficiency of the Kuzbass coal mines. At present, the influence of electric receivers on the level of consumption of active and reactive power is not taken into account, therefore, the proposed measures to increase the energy efficiency are not optimal. The article analyzes the L-shaped and T-shaped circuit for the replacement of an asynchronous motor (AM), according to the results of which it is determined that the T-shaped replacement scheme is the most accurate for determination of static load characteristics. The authors proposed and implemented in the MATLAB Simulink environment an algorithm for determining the static voltage characteristics of the motor load.

Application of neural networks for the prediction of rock fragmentation in Chadormalu iron mine / Zastosowanie sieci neuronowych do prognozowania stopnia rozdrobnienia skał w kopalni rud żelaza w Chadormalu

NASA Astrophysics Data System (ADS)

Monjezi, Masoud; Ahmadi, Zabiholla; Khandelwal, Manoj

2012-12-01

Most open-pit mining operations employ blasting for primary breakage of the in-situ rock mass. Inappropriate blasting techniques can result in excessive damage to the wall rock, decreasing stability and increasing water influx. In addition, it will result in either over and/or under breakage of rocks. The presence of over broken rocks can result in decreased wall stability and require additional excavation. In contrast, the presence of under broken rocks may require secondary blasting and additional crushing. Since blasting is a major cost factor, both cases (under and over breakage) create additional costs reflected in the increase of the operation and maintenance of the machinery. Quick and accurate measurements of fragment size distribution are essential for managing fragmented rock and other materials. Various fragmentation measurement techniques are available and are being used by industry/researchers but most of the methods are time consuming and not precise. An ideally performed blasting operation enormously influences the overall mining cost. This aim can be achieved by proper prediction and attenuation of fragmentation. Prediction of fragmentation is essential for optimizing blasting operation. Poor performance of the empirical models for predicting fragmentation has urged the application of new approaches. In this paper, artificial neural network (ANN) method is implemented to develop a model to predict rock fragmentation size distribution due to blasting in Chadormalu iron mine, Iran. In the development of the proposed ANN model, ten parameters such as UCS, drilling rate, water content, burden, spacing, stemming, hole diameter, bench height, powder factor and charge per delay were incorporated. Training and testing of the model was performed by the back-propagation algorithm using 97 datasets. A four-layer ANN was found to be optimum with architecture of 10-7-5-1. A comparison has made between measured results of fragmentation with predicted results of fragmentation by ANN and multiple regression model. Sensitivity analysis was also performed to understand the effect of each influencing parameters on rock fragmentation.

Reservoir-flooded river mouth areas as sediment traps revealing erosion from peat mining areas - Jukajoki case study in eastern Finland

NASA Astrophysics Data System (ADS)

Tahvanainen, Teemu; Meriläinen, Henna-Kaisa; Haraguchi, Akira; Simola, Heikki

2016-04-01

Many types of soil-disturbing land use have caused excess sedimentation in Finnish lakes. Identification and quantification of catchment sources of sediment material is crucial in cases where demands for remediation measures are considered. We studied recent (50 yr) sediments of four small rivers, all draining to a reservoir impounded in 1971. Catchments of two of the rivers had had peat mining activities from early 1980s until recently, exposing large areas of peat surfaces to erosion. The water level of the reservoir had risen to the river mouth areas of all rivers, while in each case, the river mouth areas still form riverine narrows separable from the main reservoir, hence collecting sedimentation from their own catchments. The original soils under the reservoir water level could readily be observed in core samples, providing a dated horizon under recent sediments. In addition, we used 137Cs-stratigraphies for dating of samples from original river bed locations. As expected, recent sediments of rivers with peat mining influence differed from others e.g. by high organic content and C:N ratios. Stable isotopes 13C and 15N both correlated with C:N (r = 0.799 and r = -0.717, respectively) and they also differentiated the peat-mining influenced samples from other river sediments. Principal components of the physical-chemical variables revealed clearer distinction than any variables separately. Light-microscopy revealed abundance of leafs of Sphagnum mosses in peat-mining influenced river sediments that were nearly absent from other rivers. Spores of Sphagnum were, however, abundant in all river sediments indicating their predominantly airborne origin. We find that combination of several physical-chemical characters rather than any single variable and microscopy of plant remains can result in reliable recognition of peatland-origin of sediment material when non-impacted sites are available for comparison. Dating of disturbed recent sediments is challenging. River-mouth areas with reservoir history can be particularly useful as the terrestrial soil strata provides a dated horizon under recent sediments.

A comprehensive assessment of exposures to respirable dust and silica in the taconite mining industry.

PubMed

Hwang, Jooyeon; Ramachandran, Gurumurthy; Raynor, Peter C; Alexander, Bruce H; Mandel, Jeffrey H

2017-05-01

This study assessed the present-day levels (year 2010-2011) of exposure to respirable dust (RD) and respirable silica (RS) in taconite mines and evaluated how the mining process influences exposure concentrations. Personal samples (n = 679) were collected to assess exposure levels of workers to RD and RS at six mines in the Mesabi Iron Range of Minnesota. The RD and RS concentrations were measured using the National Institute for Occupational Safety and Health (NIOSH) 0600 and NIOSH 7500, respectively. Between-mine, between-SEG (similar exposure groups), within-SEG, and within-worker components of variability for RD and RS exposures were estimated using a two- or three-way nested random-effects ANOVA model. The majority of RD concentrations across all mines were below the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL). The highest concentrations of RD were often observed in either the Pelletizing or Crushing departments, which are inherently dusty operations. With a few exceptions, the concentrations of RS in the crushing and concentrating processes were higher than those in the other mining processes, as well as higher than the American Conference of Governmental Industrial Hygienists (ACGIH) Threshold Limit Value (TLV) for RS. The magnetic separation and flotation processes in the concentrating department reduced the levels of RS significantly, and lowered the percentage of quartz in RD in the pelletizing department. There was little variability among the six mines or between the two mineralogically distinct zones for either RD or RS exposures. The between-SEG variability for RS did not differ substantially across most of the mines and was a major component of exposure variance. The within-SEG (or between-worker) variance component was typically the smallest because in many instances one worker from a SEG within a mine was monitored multiple times. Some of these findings were affected by the degree of censoring in each SEG and mine, characteristics of the taconite rock, seasonal effects during sampling, or the tasks assigned to each job in that mine.

Analysis of Mining-induced Valley Closure Movements

NASA Astrophysics Data System (ADS)

Zhang, C.; Mitra, R.; Oh, J.; Hebblewhite, B.

2016-05-01

Valley closure movements have been observed for decades in Australia and overseas when underground mining occurred beneath or in close proximity to valleys and other forms of irregular topographies. Valley closure is defined as the inward movements of the valley sides towards the valley centreline. Due to the complexity of the local geology and the interplay between several geological, topographical and mining factors, the underlying mechanisms that actually cause this behaviour are not completely understood. A comprehensive programme of numerical modelling investigations has been carried out to further evaluate and quantify the influence of a number of these mining and geological factors and their inter-relationships. The factors investigated in this paper include longwall positional factors, horizontal stress, panel width, depth of cover and geological structures around the valley. It is found that mining in a series passing beneath the valley dramatically increases valley closure, and mining parallel to valley induces much more closure than other mining orientations. The redistribution of horizontal stress and influence of mining activity have also been recognised as important factors promoting valley closure, and the effect of geological structure around the valley is found to be relatively small. This paper provides further insight into both the valley closure mechanisms and how these mechanisms should be considered in valley closure prediction models.

Modeling Patterns of Total Dissolved Solids Release from Central Appalachia, USA, Mine Spoils.

PubMed

Clark, Elyse V; Zipper, Carl E; Daniels, W Lee; Orndorff, Zenah W; Keefe, Matthew J

2017-01-01

Surface mining in the central Appalachian coalfields (USA) influences water quality because the interaction of infiltrated waters and O with freshly exposed mine spoils releases elevated levels of total dissolved solids (TDS) to streams. Modeling and predicting the short- and long-term TDS release potentials of mine spoils can aid in the management of current and future mining-influenced watersheds and landscapes. In this study, the specific conductance (SC, a proxy variable for TDS) patterns of 39 mine spoils during a sequence of 40 leaching events were modeled using a five-parameter nonlinear regression. Estimated parameter values were compared to six rapid spoil assessment techniques (RSATs) to assess predictive relationships between model parameters and RSATs. Spoil leachates reached maximum values, 1108 ± 161 μS cm on average, within the first three leaching events, then declined exponentially to a breakpoint at the 16th leaching event on average. After the breakpoint, SC release remained linear, with most spoil samples exhibiting declines in SC release with successive leaching events. The SC asymptote averaged 276 ± 25 μS cm. Only three samples had SCs >500 μS cm at the end of the 40 leaching events. Model parameters varied with mine spoil rock and weathering type, and RSATs were predictive of four model parameters. Unweathered samples released higher SCs throughout the leaching period relative to weathered samples, and rock type influenced the rate of SC release. The RSATs for SC, total S, and neutralization potential may best predict certain phases of mine spoil TDS release. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Problems of land reclamation during liquidation of coalmining enterprises

NASA Astrophysics Data System (ADS)

Pospehov, G. B.; Pankratova, K. V.; Straupnik, I. A.; Ustiugov, D. L.

2017-10-01

The paper presents data on the influence of coal-mining industry elimination on the deformation of land surface which can cause accidents and destructions of buildings and constructions located nearby the closed pits or mines. The analysis is carried out and the major factors which influence change of the intense deformed condition of the massif of rocks were revealed. The example of the monitoring system which will provide researchers with information for preparation of the project of a pit or a mine closing is presented, and it also will allow one to predict behavior of the massif in the future.

Effects of drying-wetting and freezing-thawing cycle on leachability of metallic elements in mine soils

NASA Astrophysics Data System (ADS)

Bang, H.; Kim, J.; Hyun, S.

2016-12-01

Mine leachate derived from contaminated mine sites with metallic elements can pose serious risks on human society and environment. Only labile fraction of metallic elements in mine soils is subject to leaching and movement by rainfall. Lability of metallic element in soil is a function of bond strengths between metal and soil surfaces, which is influenced by environmental condition (e.g., rainfall intensity, duration, temperature, etc.) The purpose of this study was to elucidate the effects of various climate conditions on the leaching patterns and lability of metallic elements in mine soils. To do this, two mine soils were sampled from two abandoned mine sites located in Korea. Leaching test were conducted using batch decant-refill method. Various climatic conditions were employed in leaching test such as (1) oven drying (40oC) - wetting cycles, (2) air drying (20oC) - wetting cycle, and (3) freezing (-40oC) - thawing cycles. Duration of drying and freezing were varied from 4 days to 2 weeks. Concentration of metallic elements, pH, Eh and concentration of dissolved iron and sulfate in leachate from each leaching process was measured. To identify the changes of labile fraction in mine soils after each of drying or freezing period, sequential extraction procedure (five fraction) was used to compare labile fraction (i.e., F1 + F2) of metallic elements. The concentration of metallic elements in mine leachate was increased after drying and freezing procedure. The amounts of released metallic element from mine soils was changed depending on their drying or freezing period. In addition, labile fraction of metallic elements in soil was also changed after drying and freezing. The changes in labile fraction after drying and freezing might be due to the increased soil surface area by pore water volume expansion. Further study is therefore needed to evaluate the impact of altered physical properties of soils such as hydration of soil surface area and shrinking by drying and freezing cycles.

Introducing Text Analytics as a Graduate Business School Course

ERIC Educational Resources Information Center

Edgington, Theresa M.

2011-01-01

Text analytics refers to the process of analyzing unstructured data from documented sources, including open-ended surveys, blogs, and other types of web dialog. Text analytics has enveloped the concept of text mining, an analysis approach influenced heavily from data mining. While text mining has been covered extensively in various computer…

Numerical Simulation of Aerogasdynamics Processes in A Longwall Panel for Estimation of Spontaneous Combustion Hazards

NASA Astrophysics Data System (ADS)

Meshkov, Sergey; Sidorenko, Andrey

2017-11-01

The relevance of a solution of the problem of endogenous fire safety in seams liable to self-ignition is shown. The possibilities of numerical methods of researches of gasdynamic processes are considered. The analysis of methodical approaches with the purpose to create models and carry out numerical researches of aerogasdynamic processes in longwall panels of gas mines is made. Parameters of the gob for longwall mining are considered. The significant influence of geological and mining conditions of conducting mining operations on distribution of air streams on longwall panels and effective management of gas emission is shown. The aerogasdynamic model of longwall panels for further research of influence of parameters of ventilation and properties of gob is presented. The results of numerical researches including distribution of air streams, fields of concentration of methane and oxygen at application of various schemes of airing for conditions of perspective mines of the Pechora basin and Kuzbass are given. Recommendations for increase of efficiency of the coal seams mining liable to selfignition are made. The directions of further researches are defined.

The possibility of increasing the efficiency of accessible coal deposits by optimizing dimensions of protective pillars or the scope of exploitation

NASA Astrophysics Data System (ADS)

Bańka, Piotr; Badura, Henryk; Wesołowski, Marek

2017-11-01

One of the ways to protect objects exposed to the influences of mining exploitation is establishing protective pillars for them. Properly determined pillar provides effective protection of the object for which it was established. Determining correct dimensions of a pillar requires taking into account contradictory requirements. Protection measures against the excessive influences of mining exploitation require designing the largest possible pillars, whereas economic requirements suggest a maximum reduction of the size of resources left in the pillar. This paper presents algorithms and programs developed for determining optimal dimensions of protective pillars for surface objects and shafts. The issue of designing a protective pillar was treated as a nonlinear programming task. The objective function are the resources left in a pillar while nonlinear limitations are the deformation values evoked by the mining exploitation. Resources in the pillar may be weighted e.g. by calorific value or by the inverse of output costs. The possibility of designing pillars of any polygon shape was taken into account. Because of the applied exploitation technologies the rectangular pillar shape should be considered more advantageous than the oval one, though it does not ensure the minimization of resources left in a pillar. In this article there is also presented a different approach to the design of protective pillars, which instead of fixing the pillar boundaries in subsequent seams, the length of longwall panels of the designed mining exploitation is limited in a way that ensures the effective protection of an object while maximizing the extraction ratio of the deposit.

Taxation and regulation of uranium mining in Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1990-11-01

Government taxation and regulation have a profound influence on mineral operations. In Canada, taxation occurs both on the federal and provincial levels. In addition, both federal and provincial regulations also affect mine operations, sometimes with overlapping, or conflicting, legislation and jurisdiction. Three broad areas of regulation affect the mine production of uranium in Canada: (1) mining law or mineral rights; (2) the licensing procedures; and (3) regulation of occupational health and safety.

Using enzyme bioassays as a rapid screen for metal toxicity

USGS Publications Warehouse

Choate, LaDonna M.; Ross, P.E.; Blumenstein, E. P.; Ranville, James F.

2005-01-01

Mine tailings piles and abandoned mine soils are often contaminated by a suite of toxic metals, which were released in the mining process. Traditionally, toxicity of such areas has been determined by numerous chemical methods including the Toxicity Characteristic Leachate Procedure (TCLP) and traditional toxicity tests using organisms such as the cladoceran Ceriodaphnia dubia. Such tests can be expensive and time-consuming. Enzymatic bioassays may provide an easier, less costly, and more time-effective toxicity screening procedure for mine tailings and abandoned mine soil leachates. This study evaluated the commercially available MetPLATE™ enzymatic toxicity assay test kit. The MetPLATE™ assay uses a modified strain of Escherichia coli bacteria as the test organism. Toxicity is defined by the activity of β-galactosidase enzyme which is monitored colorometrically with a 96-well spectrophotometer. The study used water samples collected from North Fork Clear Creek, a mining influenced water (MIW) located in Colorado. A great benefit to using the MetPLATE™ assay over the TCLP is that it shows actual toxicity of a sample by taking into account the bioavailability of the toxicants rather than simply measuring the metal concentration present. Benefits of the MetPLATE™ assay over the use of C. dubia include greatly reduced time for the testing process (∼2 hours), a more continuous variable due to a greater number of organisms present in each sample (100,000+), and the elimination of need to maintain a culture of organisms at all times.

Impacts of climate and insect defoliators on productivity and function of trembling aspen (Populus tremuloides) in Alaskan boreal forests

NASA Astrophysics Data System (ADS)

Boyd, M. A.; Walker, X. J.; Rogers, B. M.; Goetz, S. J.; Wagner, D.; Mack, M. C.

2017-12-01

Climate change has increased tree mortality and growth decline in forested ecosystems worldwide. In response to warming and drying of the boreal forest, trembling aspen (Populus tremuloides) has experienced recent large-scale productivity declines. Although declines in productivity are thought to be primarily a result of moistures stress, infestation is another major driver of aspen decline and may interact strongly with climate. Throughout interior Alaska widespread and consistent foliar damage by the aspen epidermal leaf miner Phyllocnistis populiella has been observed concurrent with some of the warmest and driest growing seasons on record. Here we use tree ring measurements and remote sensing indices of vegetation productivity (NDVI) to study the influence of leaf miner and climate on aspen productivity and physiology in the Alaskan boreal forest, and assess if NDVI reflects variations in these ground-based measurements. We assessed ring width and tree ring stable carbon isotope (d13C) response of aspen to infestation and a climate moisture index (CMI) from 2004 - 2014. We found that when growth was negatively correlated to infestation, then it was no longer positively influenced by moisture availability during the growing season. Regardless of the radial growth response to leaf mining, tree ring d13C decreased with increasing infestation. We also found that NDVI was influenced by leaf mining and showed a positive correlation with tree ring d13C, which suggests that NDVI is reflective of changes in tree characteristics under leaf mining that influence tree ring d13C. This finding also reveals the prospect of using satellite data to monitor fluctuations in tree physiology during leaf miner infestation. Our results indicate that aspen productivity will be severely hindered during leaf miner infestation, and that infestation will inhibit the ability of aspen to respond to favorable climate conditions by increasing growth and potentially photosynthesis. This suggests that the productivity, reproduction, and health of aspen in boreal forests, and in turn any related biophysical or carbon sequestration benefits, may become limited under future warming if infestation by leaf miner continues or accelerates.

Ultrasound-assisted extraction for total sulphur measurement in mine tailings.

PubMed

Khan, Adnan Hossain; Shang, Julie Q; Alam, Raquibul

2012-10-15

A sample preparation method for percentage recovery of total sulphur (%S) in reactive mine tailings based on ultrasound-assisted digestion (USAD) and inductively coupled plasma-optical emission spectroscopy (ICP-OES) was developed. The influence of various methodological factors was screened by employing a two-level and three-factor (2(3)) full factorial design and using KZK-1, a sericite schist certified reference material (CRM), to find the optimal combination of studied factors and %S. Factors such as the sonication time, temperature and acid combination were studied, with the best result identified as 20 min of sonication, 80°C temperature and 1 ml of HNO(3):1 ml of HCl, which can achieve 100% recovery for the selected CRM. Subsequently a fraction of the 2(3) full factorial design was applied to mine tailings. The percentage relative standard deviation (%RSD) for the ultrasound method is less than 3.0% for CRM and less than 6% for the mine tailings. The investigated method was verified by X-ray diffraction analysis. The USAD method compared favorably with existing methods such as hot plate assisted digestion method, X-ray fluorescence and LECO™-CNS method. Copyright © 2012 Elsevier B.V. All rights reserved.

Environmental contamination in an Australian mining community and potential influences on early childhood health and behavioural outcomes.

PubMed

Dong, Chenyin; Taylor, Mark Patrick; Kristensen, Louise Jane; Zahran, Sammy

2015-12-01

Arsenic, cadmium and lead in aerosols, dusts and surface soils from Australia's oldest continuous lead mining town of Broken Hill were compared to standardised national childhood developmental (year 1) and education performance measures (years 3,5,7,9). Contaminants close to mining operations were elevated with maximum lead levels in soil: 8900 mg/kg; dust wipe: 86,061 μg/m(2); dust deposition: 2950 μg/m(2)/day; aerosols: 0.707 μg/m(3). The proportion of children from Broken Hill central, the area with the highest environmental contamination, presented with vulnerabilities in two or more developmental areas at 2.6 times the national average. Compared with other school catchments of Broken Hill, children in years 3 and 5 from the most contaminated school catchment returned consistently the lowest educational scores. By contrast, children living and attending schools associated with lower environmental contamination levels recorded higher school scores and lower developmental vulnerabilities. Similar results were identified in Australia's two other major lead mining and smelting cities of Port Pirie and Mount Isa. Copyright © 2015 Elsevier Ltd. All rights reserved.

Technologies for Decreasing Mining Losses

NASA Astrophysics Data System (ADS)

Valgma, Ingo; Väizene, Vivika; Kolats, Margit; Saarnak, Martin

2013-12-01

In case of stratified deposits like oil shale deposit in Estonia, mining losses depend on mining technologies. Current research focuses on extraction and separation possibilities of mineral resources. Selective mining, selective crushing and separation tests have been performed, showing possibilities of decreasing mining losses. Rock crushing and screening process simulations were used for optimizing rock fractions. In addition mine backfilling, fine separation, and optimized drilling and blasting have been analyzed. All tested methods show potential and depend on mineral usage. Usage in addition depends on the utilization technology. The questions like stability of the material flow and influences of the quality fluctuations to the final yield are raised.

Measuring mine roof bolt strains

DOEpatents

Steblay, Bernard J.

1986-01-01

A mine roof bolt and a method of measuring the strain in mine roof bolts of this type are disclosed. According to the method, a flat portion on the head of the mine roof bolt is first machined. Next, a hole is drilled radially through the bolt at a predetermined distance from the bolt head. After installation of the mine roof bolt and loading, the strain of the mine roof bolt is measured by generating an ultrasonic pulse at the flat portion. The time of travel of the ultrasonic pulse reflected from the hole is measured. This time of travel is a function of the distance from the flat portion to the hole and increases as the bolt is loaded. Consequently, the time measurement is correlated to the strain in the bolt. Compensation for various factors affecting the travel time are also provided.

The influence of coal physical and mechanical properties and mining energy consumption factor on airborne respirable dust level

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koziel, A.; Malec, M.; Wardas, E.

1999-07-01

The fact that there are not any explicitly defined relationships describing the influence of physical and mechanical properties of coal and of energy consumption factor on dust level prompted Polish and American investigators to carry out a joint research project within the framework of the US-Poland Maria Sklodowska-Curie Joint Fund II. The paper presents methods used to perform tests under laboratory conditions at the Pittsburgh Research Laboratory as well as under real conditions in the course of coal cutting in Polish coal mines. Measuring systems and results of the tests are described. The analysis carried out has provided a basismore » for determining the influence of specified operational parameters, i.e., coal compression strength R{sub c}, coal cuttability factor A, energy consumption factor of mining E{sub uc}, load of cutting drums as well as of laboratory parameters, i.e., grindability, coal breakage characteristics (product size distribution), moisture content, volatile and fixed carbon content, specific energy of crushing on a level of generated dust (total dust, specific dust and airborne respirable dust). The effect of technical parameters, i.e., face height, airflow velocity in a face, amount and pressure of water in spraying systems of longwall shearers, depth of cut taken by a cutting drum and application of powered cowls on dust level under operating conditions are also presented. Results of the tests made it possible to work out guidelines relating to methods and technology for effective reduction of dust emission on longwall faces.« less

Investigation of Rock Mass Stability Around the Tunnels in an Underground Mine in USA Using Three-Dimensional Numerical Modeling

NASA Astrophysics Data System (ADS)

Xing, Yan; Kulatilake, P. H. S. W.; Sandbak, L. A.

2018-02-01

The stability of the rock mass around the tunnels in an underground mine was investigated using the distinct element method. A three-dimensional model was developed based on the available geological, geotechnical, and mine construction information. It incorporates a complex lithological system, persistent and non-persistent faults, and a complex tunnel system including backfilled tunnels. The strain-softening constitutive model was applied for the rock masses. The rock mass properties were estimated using the Hoek-Brown equations based on the intact rock properties and the RMR values. The fault material behavior was modeled using the continuously yielding joint model. Sequential construction and rock supporting procedures were simulated based on the way they progressed in the mine. Stress analyses were performed to study the effect of the horizontal in situ stresses and the variability of rock mass properties on tunnel stability, and to evaluate the effectiveness of rock supports. The rock mass behavior was assessed using the stresses, failure zones, deformations around the tunnels, and the fault shear displacement vectors. The safety of rock supports was quantified using the bond shear and bolt tensile failures. Results show that the major fault and weak interlayer have distinct influences on the displacements and stresses around the tunnels. Comparison between the numerical modeling results and the field measurements indicated the cases with the average rock mass properties, and the K 0 values between 0.5 and 1.25 provide satisfactory agreement with the field measurements.

Landfill mining in Austria: foundations for an integrated ecological and economic assessment.

PubMed

Hermann, Robert; Baumgartner, Rupert J; Sarc, Renato; Ragossnig, Arne; Wolfsberger, Tanja; Eisenberger, Martin; Budischowsky, Andreas; Pomberger, Roland

2014-09-01

For the first time, basic technical and economic studies for landfill mining are being carried out in Austria on the basis of a pilot project. An important goal of these studies is the collection of elementary data as the basis for an integrated ecological and economic assessment of landfill mining projects with regard to their feasibility. For this purpose, economic, ecological, technical, organizational, as well as political and legal influencing factors are identified and extensively studied in the article. An important aspect is the mutual influence of the factors on each other, as this can significantly affect the development of an integrated assessment system. In addition to the influencing factors, the definition of the spatial and temporal system boundaries is crucial for further investigations. Among others, the quality and quantity of recovered waste materials, temporal fluctuations or developments in prices of secondary raw material and fuels attainable in the markets, and time and duration of dumping, play a crucial role. Based on the investigations, the spatial system boundary is defined in as much as all the necessary process steps, from landfill mining, preparing and sorting to providing a marketable material/product by the landfill operator, are taken into account. No general accepted definition can be made for the temporal system boundary because the different time-related influencing factors necessitate an individual project-specific determination and adaptation to the facts of the on-site landfill mining project. © The Author(s) 2014.

ARSENIC SPECIATION, SEASONAL TRANSFORMATIONS, AND CO-DISTRIBUTION WITH IRON IN A MINE WASTE-INFLUENCED PALUSTRINE EMERGENT WETLAND. (R825399)

EPA Science Inventory

Arsenic is commonly associated with mined ores and thus may be detrimental to naturally occurring wetlands that reside in mine waste-impacted regions. Understanding the relationship between Fe and As in both the aqueous and solid phase is critical for assessing the risk As impose...

INFLUENCE OF PH AND OXIDATION-REDUCTION POTENTIAL (EH) ON THE DISSOLUTION OF MERCURY-CONTAINING MINE WASTES FROM THE SULFUR BANK MERCURY MINE

EPA Science Inventory

This study was undertaken as a part of developing treatment alternatives for waste materials, primarily waste rock and roaster tailings, from sites contaminated with mercury (Hg) mining wastes. Leaching profiles of waste rock over a range of different pH and oxidation-reduction (...

Impacts of manganese mining activity on the environment: interactions among soil, plants, and arbuscular mycorrhiza.

PubMed

Rivera-Becerril, Facundo; Juárez-Vázquez, Lucía V; Hernández-Cervantes, Saúl C; Acevedo-Sandoval, Otilio A; Vela-Correa, Gilberto; Cruz-Chávez, Enrique; Moreno-Espíndola, Iván P; Esquivel-Herrera, Alfonso; de León-González, Fernando

2013-02-01

The mining district of Molango in the Hidalgo State, Mexico, possesses one of the largest deposits of manganese (Mn) ore in the world. This research assessed the impacts of Mn mining activity on the environment, particularly the interactions among soil, plants, and arbuscular mycorrhiza (AM) at a location under the influence of an open Mn mine. Soils and plants from three sites (soil under maize, soil under native vegetation, and mine wastes with some vegetation) were analyzed. Available Mn in both soil types and mine wastes did not reach toxic levels. Samples of the two soil types were similar regarding physical, chemical, and biological properties; mine wastes were characterized by poor physical structure, nutrient deficiencies, and a decreased number of arbuscular mycorrhizal fungi (AMF) spores. Tissues of six plant species accumulated Mn at normal levels. AM was absent in the five plant species (Ambrosia psilostachya, Chenopodium ambrosoides, Cynodon dactylon, Polygonum hydropiperoides, and Wigandia urens) established in mine wastes, which was consistent with the significantly lower number of AMF spores compared with both soil types. A. psilostachya (native vegetation) and Zea mays showed mycorrhizal colonization in their root systems; in the former, AM significantly decreased Mn uptake. The following was concluded: (1) soils, mine wastes, and plant tissues did not accumulate Mn at toxic levels; (2) despite its poor physical structure and nutrient deficiencies, the mine waste site was colonized by at least five plant species; (3) plants growing in both soil types interacted with AMF; and (4) mycorrhizal colonization of A. psilostachya influenced low uptake of Mn by plant tissues.

Loads from Compressive Strain Caused by Mining Activity Illustrated with the Example of Two Buildings in Silesia

NASA Astrophysics Data System (ADS)

Kadela, Marta; Chomacki, Leszek

2017-10-01

The soil’s load on retention walls or underground elements of engineering structures consists of three basic types of pressure: active pressure (p a ), passive pressure (p b ) and at-rest pressure (p 0 ). In undisturbed areas without any mining, due to lack of activity in the soil, specific forces from the soil are stable and unchanging throughout the structure’s life. Mining activity performed at a certain depth activates the soil. Displacements take place in the surface layer of the rock mass, which begins to act on the structure embedded in it, significantly changing the original stress distribution. Deformation of the subgrade, mainly horizontal strains, becomes a source of significant additional actions in the contact zone between the structure and the soil, constituting an additional load for the structure. In order to monitor the mining influence in the form of compressive load on building walls, an observation line was set up in front of two buildings located in Silesia (in Mysłowice). In 2013, some mining activity took place directly under those buildings, with expected horizontal strains of εx = -5.8 mm/m. The measurement results discussed in this paper showed that, as predicted, the buildings were subjected only to horizontal compressive strains with the values parallel to the analysed wall being less than -4.0 ‰ for first building and -1.5‰ for second building, and values perpendicular to the analysed wall being less than -6.0‰ for first building and -4.0‰ for second building (the only exception was the measurement in line 8-13, where εx = -17.04‰ for first building and -4.57‰ for second building). The horizontal displacement indicate that the impact of mining activity was greater on first building. This is also confirmed by inspections of the damage.

Analysis by the Residual Method for Estimate Market Value of Land on the Areas with Mining Exploitation in Subsoil under Future New Building

NASA Astrophysics Data System (ADS)

Gwozdz-Lason, Monika

2017-12-01

This paper attempts to answer some of the following questions: what is the main selling advantage of a plot of land on the areas with mining exploitation? which attributes influence on market value the most? and how calculate the mining influence in subsoil under future new building as market value of plot with commercial use? This focus is not accidental, as the paper sets out to prove that the subsoil load bearing capacity, as directly inferred from the local geotechnical properties with mining exploitation, considerably influences the market value of this type of real estate. Presented in this elaborate analysis and calculations, are part of the ongoing development works which aimed at suggesting a new technology and procedures for estimating the value of the land belonging to the third category geotechnical. Analysed the question was examined both in terms of the theoretical and empirical. On the basis of the analysed code calculations in residual method, numerical, statistical and econometric defined results and final conclusions. A market analysis yielded a group of subsoil stabilization costs which depend on the mining operations interaction, subsoil parameters, type of the contemplated structure, its foundations, selected stabilization method, its overall area and shape.

Quantification of the inevitable: the influence of soil macrofauna on soil water movement in rehabilitated open-cut mined lands

NASA Astrophysics Data System (ADS)

Arnold, S.; Williams, E. R.

2016-01-01

Recolonisation of soil by macrofauna (especially ants, termites and earthworms) in rehabilitated open-cut mine sites is inevitable and, in terms of habitat restoration and function, typically of great value. In these highly disturbed landscapes, soil invertebrates play a major role in soil development (macropore configuration, nutrient cycling, bioturbation, etc.) and can influence hydrological processes such as infiltration, seepage, runoff generation and soil erosion. Understanding and quantifying these ecosystem processes is important in rehabilitation design, establishment and subsequent management to ensure progress to the desired end goal, especially in waste cover systems designed to prevent water reaching and transporting underlying hazardous waste materials. However, the soil macrofauna is typically overlooked during hydrological modelling, possibly due to uncertainties on the extent of their influence, which can lead to failure of waste cover systems or rehabilitation activities. We propose that scientific experiments under controlled conditions and field trials on post-mining lands are required to quantify (i) macrofauna-soil structure interactions, (ii) functional dynamics of macrofauna taxa, and (iii) their effects on macrofauna and soil development over time. Such knowledge would provide crucial information for soil water models, which would increase confidence in mine waste cover design recommendations and eventually lead to higher likelihood of rehabilitation success of open-cut mining land.

LANDSAT inventory of surface-mined areas using extendible digital techniques

NASA Technical Reports Server (NTRS)

Anderson, A. T.; Schultz, D. T.; Buchman, N.

1975-01-01

Multispectral LANDSAT imagery was analyzed to provide a rapid and accurate means of identification, classification, and measurement of strip-mined surfaces in Western Maryland. Four band analysis allows distinction of a variety of strip-mine associated classes, but has limited extendibility. A method for surface area measurements of strip mines, which is both geographically and temporally extendible, has been developed using band-ratioed LANDSAT reflectance data. The accuracy of area measurement by this method, averaged over three LANDSAT scenes taken between September 1972 and July 1974, is greater than 93%. Total affected acreage of large (50 hectare/124 acre) mines can be measured to within 1.0%.

[Influence of work intensity on development of arterial hypertension in metal-mining workers].

PubMed

Ustinova, O Iu; Alekseev, V B; Rumiantseva, A N; Orehova, Ia V

2013-01-01

The article covers data on influence of working shifts duration and shift work intensity on cardiovascular system functioning in operators of mining excavators. Findings are that 8 hours shift with regular shift schedule (40 working hours per week) gives significant load on cardiovascular system of workers engaged into underground activities. 50% of mining excavator operators following this working schedule develop transitory arterial hypertension within 10 years. Longer work shift over 8 hours and more intensive shifting schedule over 40 hours per week causes stable arterial hypertension within 3 months in 60% of workers, in 10% of cases associated with lower functioning of sinus node.

Historical flux of mercury associated with mining and industrial sources in the Marano and Grado Lagoon (northern Adriatic Sea)

NASA Astrophysics Data System (ADS)

Covelli, Stefano; Langone, Leonardo; Acquavita, Alessandro; Piani, Raffaella; Emili, Andrea

2012-11-01

The "MIRACLE" Project was established in order to assess the feasibility of clam farming and high levels of sediment mercury (Hg) contamination coexisting in the Marano and Grado Lagoon, Italy. This lagoon has been subjected to Hg input from both industrial waste (chlor-alkali plant) and long-term mining activity (Idrija mine, NW Slovenia). One of the subtasks of the "MIRACLE" Project was to determine the historical evolution of Hg accumulation in the lagoon's bottom sediments. Thirteen 1-m deep sediment cores were collected from the subtidal and intertidal zones, plus one in a saltmarsh, all of which were then analyzed for total Hg content and several physicochemical parameters. Sedimentation rate assessments were performed by measuring short-lived radionuclides (excess 210Pb and 137Cs). For most of the analyzed cores, natural background levels of Hg were observed at depths of 50-100 cm. In the eastern area, Hg contamination was found to be at its maximum level at the core top (up to 12 μg g-1) as a consequence of the long-term mining activity. The vertical distribution of Hg was related to the influence of the single-point contamination sources, whereas the grain-size variability or organic matter content seemed not to affect it. In the western area, Hg content at the surface was found not to exceed 7 μg g-1 and contamination was recorded only in the first 20-30 cm. Geochronological measurements showed that the depositional flux of Hg was influenced by anthropogenic inputs after 1800, when mining activity was more intense. After 1950, Hg in the surface sediment, most remarkable in the central-western sector, seemed to also be affected by the discharge of the Aussa River, which delivers Hg from the chlor-alkali plant. In 1996, Hg mining at Idrija ceased, however the core profiles did not show any subsequent decreasing trend in terms of Hg flux, which implies the system retaining some "memory" of contamination. Thus, in the short term, a decrease in Hg inputs into the nearby Gulf of Trieste and the lagoon seems unlikely. A preliminary rounded-down gross estimate of total Hg "trapped" in the lagoon's sediments amounted to 251 t. Such a quantity, along with the complexity of the lagoon ecosystem, suggests that an in toto reclamation of the sediments at the lagoon scale is unfeasible, both economically and environmentally.

Effects of human and organizational deficiencies on workers'safety behavior in a mining site in Iran.

PubMed

Mirzaei Aliabadi, Mostafa; Aghaei, Hamed; Kalatpour, Omid; Soltanian, Ali Reza; SeyedTabib, Maryam

2018-05-18

Mines are a dangerous workplace worldwide with a high accident rate. According to the Statistical Center of Iran, the number of occupational accidents in Iranian mines has increased in recent years. This study determined and explained human and organizational deficiencies influencing Iranian mining accidents. In this study, the data associated with 305 mining accidents were investigated. The data were analyzed based on a systems analysis approach to identify critical deficiencies in organizational influences, unsafe supervision, preconditions for unsafe acts, and workers' unsafe acts. Partial Least Square Structural Equation Modeling [PLS-SEM] was utilized for modeling the interactions between these deficiencies. It was demonstrated that organizational deficiencies had a direct positive effect on workers' violations (path coefficient=0.16) and workers' errors (path coefficient=0.23). The effect of unsafe supervision on workers' violations and workers' errors was also significant with the path coefficients of 0.14 and 0.20. Likewise, preconditions for unsafe acts also had a significant effect on both workers' violations (path coefficient=0.16) and workers' errors (path coefficient=0.21). Moreover, organizational deficiencies had an indirect positive effect on workers' unsafe acts mediated by unsafe supervision and preconditions for unsafe acts. Among the variables examined in the current study, organizational influences had the strongest impacts on workers' unsafe acts. Organizational deficiencies are the main causes of accidents in mining sectors that affects all other aspects of system safety. For preventing occupational accidents, organizational deficiencies should be modified first.

PERFORMING QUALITY FLOW MEASUREMENTS AT MINE SITES

EPA Science Inventory

Accurate flow measurement data is vital to research, monitoring, and remediation efforts at mining sites. This guidebook has been prepared to provide a summary of information relating to the performance of low measurements, and how this information can be applied at mining sites....

Estimating natural background groundwater chemistry, Questa molybdenum mine, New Mexico

USGS Publications Warehouse

Verplanck, Phillip L.; Nordstrom, D. Kirk; Plumlee, Geoffrey S.; Walker, Bruce M.; Morgan, Lisa A.; Quane, Steven L.

2010-01-01

This 2 1/2 day field trip will present an overview of a U.S. Geological Survey (USGS) project whose objective was to estimate pre-mining groundwater chemistry at the Questa molybdenum mine, New Mexico. Because of intense debate among stakeholders regarding pre-mining groundwater chemistry standards, the New Mexico Environment Department and Chevron Mining Inc. (formerly Molycorp) agreed that the USGS should determine pre-mining groundwater quality at the site. In 2001, the USGS began a 5-year, multidisciplinary investigation to estimate pre-mining groundwater chemistry utilizing a detailed assessment of a proximal natural analog site and applied an interdisciplinary approach to infer pre-mining conditions. The trip will include a surface tour of the Questa mine and key locations in the erosion scar areas and along the Red River. The trip will provide participants with a detailed understanding of geochemical processes that influence pre-mining environmental baselines in mineralized areas and estimation techniques for determining pre-mining baseline conditions.

Influence of carbon source and inoculum type on anaerobic biomass adhesion on polyurethane foam in reactors fed with acid mine drainage.

PubMed

Rodriguez, Renata P; Zaiat, Marcelo

2011-04-01

This paper analyzes the influence of carbon source and inoculum origin on the dynamics of biomass adhesion to an inert support in anaerobic reactors fed with acid mine drainage. Formic acid, lactic acid and ethanol were used as carbon sources. Two different inocula were evaluated: one taken from an UASB reactor and other from the sediment of a uranium mine. The values of average colonization rates and the maximum biomass concentration (C(max)) were inversely proportional to the number of carbon atoms in each substrate. The highest C(max) value (0.35 g TVS g(-1) foam) was observed with formic acid and anaerobic sludge as inoculum. Maximum colonization rates (v(max)) were strongly influenced by the type of inoculum when ethanol and lactic acid were used. For both carbon sources, the use of mine sediment as inoculum resulted in a v(max) of 0.013 g TVS g(-1) foam day(-1), whereas 0.024 g TVS g(-1) foam day(-1) was achieved with anaerobic sludge. Copyright © 2011 Elsevier Ltd. All rights reserved.

Estimating the Importance of Terrorists in a Terror Network

NASA Astrophysics Data System (ADS)

Elhajj, Ahmed; Elsheikh, Abdallah; Addam, Omar; Alzohbi, Mohamad; Zarour, Omar; Aksaç, Alper; Öztürk, Orkun; Özyer, Tansel; Ridley, Mick; Alhajj, Reda

While criminals may start their activities at individual level, the same is in general not true for terrorists who are mostly organized in well established networks. The effectiveness of a terror network could be realized by watching many factors, including the volume of activities accomplished by its members, the capabilities of its members to hide, and the ability of the network to grow and to maintain its influence even after the loss of some members, even leaders. Social network analysis, data mining and machine learning techniques could play important role in measuring the effectiveness of a network in general and in particular a terror network in support of the work presented in this chapter. We present a framework that employs clustering, frequent pattern mining and some social network analysis measures to determine the effectiveness of a network. The clustering and frequent pattern mining techniques start with the adjacency matrix of the network. For clustering, we utilize entries in the table by considering each row as an object and each column as a feature. Thus features of a network member are his/her direct neighbors. We maintain the weight of links in case of weighted network links. For frequent pattern mining, we consider each row of the adjacency matrix as a transaction and each column as an item. Further, we map entries into a 0/1 scale such that every entry whose value is greater than zero is assigned the value one; entries keep the value zero otherwise. This way we can apply frequent pattern mining algorithms to determine the most influential members in a network as well as the effect of removing some members or even links between members of a network. We also investigate the effect of adding some links between members. The target is to study how the various members in the network change role as the network evolves. This is measured by applying some social network analysis measures on the network at each stage during the development. We report some interesting results related to two benchmark networks: the first is 9/11 and the second is Madrid bombing.

Integrated mined-area reclamation and land-use planning. Volume 3C. A case study of surface mining and reclamation planning: Georgia Kaolin Company Clay Mines, Washington County, Georgia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guernsey, J L; Brown, L A; Perry, A O

1978-02-01

This case study examines the reclamation practices of the Georgia Kaolin's American Industrial Clay Company Division, a kaolin producer centered in Twiggs, Washington, and Wilkinson Counties, Georgia. The State of Georgia accounts for more than one-fourth of the world's kaolin production and about three-fourths of U.S. kaolin output. The mining of kaolin in Georgia illustrates the effects of mining and reclaiming lands disturbed by area surface mining. The disturbed areas are reclaimed under the rules and regulations of the Georgia Surface Mining Act of 1968. The natural conditions influencing the reclamation methodologies and techniques are markedly unique from those ofmore » other mining operations. The environmental disturbances and procedures used in reclaiming the kaolin mined lands are reviewed and implications for planners are noted.« less

Effects of surface coal mining and reclamation on the geohydrology of six small watersheds in West-Central Indiana

USGS Publications Warehouse

Martin, Jeffrey D.; Duwelius, Richard F.; Crawford, Charles G.

1990-01-01

Hydrologic effects of mining and reclamation were identified by comparing the hydrologic systems at mined and reclaimed watersheds with those at unmined agricultural watersheds. The presence or absence of a large final-cut lake in the reclaimed watershed greatly influences the hydrologic systems and the effects of mining and reclamation. Surface coal mining and reclamation can decrease base flow, annual runoff, and peak flow rates; increase the variability of flow and recharge to the bedrock; reestablish the premining relation between surface- and ground-water divides; and lower the water table in upland areas.

Factors influencing mine rescue team behaviors.

PubMed

Jansky, Jacqueline H; Kowalski-Trakofler, K M; Brnich, M J; Vaught, C

2016-01-01

A focus group study of the first moments in an underground mine emergency response was conducted by the National Institute for Occupational Safety and Health (NIOSH), Office for Mine Safety and Health Research. Participants in the study included mine rescue team members, team trainers, mine officials, state mining personnel, and individual mine managers. A subset of the data consists of responses from participants with mine rescue backgrounds. These responses were noticeably different from those given by on-site emergency personnel who were at the mine and involved with decisions made during the first moments of an event. As a result, mine rescue team behavior data were separated in the analysis and are reported in this article. By considering the responses from mine rescue team members and trainers, it was possible to sort the data and identify seven key areas of importance to them. On the basis of the responses from the focus group participants with a mine rescue background, the authors concluded that accurate and complete information and a unity of purpose among all command center personnel are two of the key conditions needed for an effective mine rescue operation.

New data on the level of contamination with tritium aerosol fallout in the nearest influence zone of the mining-chemical combine of the Rosatom State Corporation

NASA Astrophysics Data System (ADS)

Bondareva, L. G.; Rubailo, A. I.

2016-03-01

The influence of tritium aerosol transport on radioactive contamination on the territory of the Krasnoyarsk region influenced by the mining-chemical combine of the Rosatom State Corporation was studied. Snow cover, foliage, and needles collected at various distances from the mining-chemical combine were selected as the object of this study. A new methodology of liquid extraction from plant material (leaves and needles) was worked out. As a result, the maximal concentrations of tritium (15 kBk/m3 in snow, 11 and 15 Bk/m2 for leaves and pine-tree needles, respectively) were determined. However, the results obtained are not anomalous. Consequently, contamination with tritium may not be accounted for entirely due to the low concentrations.

Questa baseline and pre-mining ground-water quality investigation. 10. Geologic influences on ground and surface waters in the lower Red River watershed, New Mexico

USGS Publications Warehouse

Ludington, Steve; Plumlee, Geoff; Caine, Jonathan S.; Bove, Dana; Holloway, JoAnn; Livo, Eric

2005-01-01

Introduction: This report is one in a series that presents results of an interdisciplinary U.S. Geological Survey (USGS) study of ground-water quality in the lower Red River watershed prior to open-pit and underground molybdenite mining at Molycorp's Questa mine. The stretch of the Red River watershed that extends from just upstream of the town of Red River, N. Mex., to just above the town of Questa includes several mineralized areas in addition to the one mined by Molycorp. Natural erosion and weathering of pyrite-rich rocks in the mineralized areas has created a series of erosional scars along this stretch of the Red River that contribute acidic waters, as well as mineralized alluvial material and sediments, to the river. The overall goal of the USGS study is to infer the premining ground-water quality at the Molycorp mine site. An integrated geologic, hydrologic, and geochemical model for ground water in the mineralized-but unmined-Straight Creek drainage (a tributary of the Red River) is being used as an analog for the geologic, geochemical, and hydrologic conditions that influenced ground-water quality and quantity in the Red River drainage prior to mining. This report provides an overall geologic framework for the Red River watershed between Red River and Questa, in northern New Mexico, and summarizes key geologic, mineralogic, structural and other characteristics of various mineralized areas (and their associated erosional scars and debris fans) that likely influence ground- and surface-water quality and hydrology. The premining nature of the Sulphur Gulch and Goat Hill Gulch scars on the Molycorp mine site can be inferred through geologic comparisons with other unmined scars in the Red River drainage.

Application of 3D Laser Scanning Technology in Inspection and Dynamic Reserves Detection of Open-Pit Mine

NASA Astrophysics Data System (ADS)

Hu, Zhumin; Wei, Shiyu; Jiang, Jun

2017-10-01

The traditional open-pit mine mining rights verification and dynamic reserve detection means rely on the total station and RTK to collect the results of the turning point coordinates of mining surface contours. It resulted in obtaining the results of low precision and large error in the means that is limited by the traditional measurement equipment accuracy and measurement methods. The three-dimensional scanning technology can obtain the three-dimensional coordinate data of the surface of the measured object in a large area at high resolution. This paper expounds the commonly used application of 3D scanning technology in the inspection and dynamic reserve detection of open mine mining rights.

The effect of abandoned mining ponds on trace elements dynamics in the soil-plant system

NASA Astrophysics Data System (ADS)

Gabarrón, María; Faz, Ángel; Zornoza, Raúl; Acosta, Jose A.

2017-04-01

In semiarid climate regions lack of vegetation and dryer climate contribute to erosion of abandoned mining surface areas making them up important potential sources of metal pollution into the environment. The objectives of this study were to determine the influence of mine ponds in agriculture and forest soils, and identify the dynamic of metals in the soil-plant system for native plant species (Ballota hirsuta) and crop species (Hordeum vulgare) in two ancient mining districts: La Unión and Mazarrón. To achieve these objectives, wastes samples from mine ponds and soil samples (rhizosphere and non-rhizosphere soils) from natural and agricultural lands were collected. In addition, six plants (Ballota hirsuta) from natural area and 3 plants (Hordeum vulgare) from crops were collected. Physicochemical properties and total, water soluble and bioavailable metals (Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, and Zn) and arsenic were measured in waste/soil samples. The chemical speciation of metals in soil was estimated by a sequential extraction procedure. For plants analyses, each plant were divided in roots, stem and leaves and metal content measured by ICP-MS. Results indicated that mine, natural and agricultural soils were contaminated by As, Cd, Cu, Pb, and Zn. Chemical partitioning revealed higher mobility of metals in mine ponds than natural and agriculture soils while only Fe and As are completely bound to the soil matrix due to the mineralogical compositions of soils. The accumulation of metals in Ballota hirsuta in La Union decrease as Fe>As>Cr>Ni>Cu>Zn>Cd>Mn>Co>Pb while in Mazarrón did as As>Fe>Cr>Pb>Cu>Ni>Co>Mn>Zn>Cd. Ballota hirsuta showed high ability to bio-accumulate Cu, Cr, Fe, Ni, and As, transferring a large amount to edible parts without exceeding the toxicity limits for animals. Results for barley plants (Hordeum vulgare) showed the ability to absorb and accumulate As, Fe, Mn, Pb and Zn, although the transfer ability of As, Cd and Pb was lower. Although the behavior of metals reflects a root barrier effect, the amount of Pb in grain overreached the permissible limit in aliments.

Hydrogeochemical Investigations of Historic Mining Districts, Central Western Slope of Colorado, Including Influence on Surface-Water Quality

USGS Publications Warehouse

Nash, J. Thomas

2002-01-01

This report describes reconnaissance hydrogeochemical investigations of 22 mining districts on the Western Slope of Colorado in the Gunnison and Uncompahgre National Forests and adjacent public lands administered by the Bureau of Land Management. Sources and fates of contaminants from historic mines, mine waste, and mill tailings are interpreted from chemical analyses for 190 samples of surface waters; 185 samples of mined rocks, mill tailings, and altered rocks; and passive leach analyses of 116 samples of those mineralized materials. Short reaches of several headwater streams show relatively low level effects of historic mining; the headwaters of the Uncompahgre River are highly contaminated by mines and unmined altered rocks in the Red Mountain district. There is encouraging evidence that natural processes attenuate mine-related contamination in most districts.

Case history of controlling a landslide at Panluo open-pit mine in China

NASA Astrophysics Data System (ADS)

Wei, Zuoan; Yin, Guangzhi; Wan, Ling; Shen, Louyan

2008-04-01

Controlling of landsides safely and economically is a great challenge to mine operators because landslides are major geological problems especially in open-pit mines. In this paper, a case history at Panluo open-pit mine is presented in detail to share the experiences and lessons with mine operators. Panluo open-pit mine is located in the southwestern Fujian province of China. It is the largest open-pit iron mine in the Fujian province and was planned in 1965 and is in full operation from 1978. In July 1990, an earthquake of magnitude 5.3 in Taiwan Strait and big rainstorms impacted the mine slope, causing tension cracks and rather large-scale failures, and forming a U-shaped landslide. Total potential volume was estimated to be up to 1.0 × 106 m3. This directly threatened the mine production. In order to protect the mine production and the dwellers’ safety around, a dynamic comprehensive method was implemented including geotechnical investigations, in-situ testing and monitoring, stability analysis, and many mitigation and preventive measures. These measures slowed down the development and further occurrence of the landslide. The results showed that the landslides were still active, it was slowed with the control measures and moved rapidly with rainfall and mining down. However, no catastrophic accidents occurred and the pit mining was continued till it was closed at the elevation of 887 m in 2000. As a successful case of landslide control at an open-pit mine for 10 years, this paper reports the controlling measures in details. These experiences of landslide control may be beneficial to other similar mines for landslide control.

Hydrogeochemical Investigation of the Standard Mine Vicinity, Upper Elk Creek Basin, Colorado

USGS Publications Warehouse

Manning, Andrew H.; Verplanck, Philip L.; Mast, M. Alisa; Wanty, Richard B.

2008-01-01

Ground- and surface-water samples were collected in the vicinity of the Standard Mine in west-central Colorado in order to characterize the local ground-water flow system, determine metal concentrations in local ground water, and better understand factors controlling the discharge of metal-rich waters from the mine. The sampling program included a one-time sampling of springs, mine adits, and exploration pits in Elk Basin and Redwell Basin; repeated sampling throughout one year of Standard Mine Level 1 discharge and Elk Creek near its confluence with Coal Creek; and a one-time sampling of underground sites in Levels 3 and 5 of the Standard Mine. Samples were analyzed for major ions and trace elements, stable isotopes of hydrogen (2H/1H) and oxygen (18O/16O), strontium isotopes, and tritium and dissolved noble gases (including helium isotopes) for tritium/helium-3 age dating. No clear correlations were observed between natural ground-water discharge locations and map-scale faults and lithology. Surface observations and the location of ground-water discharge suggest that simple topography, rather than large-scale geologic features, primarily controls the occurrence and flow of shallow ground water in Elk Basin. Discrete inflows from cross faults or other features were not observed in Levels 3 and 5 of the Standard Mine. Instead, water entered the mine as relatively persistent dripping from gouge and breccia within the Standard fault, which both tunnels follow. Therefore, the Standard fault itself is probably the main pathway of ground-water flow from the shallow subsurface to the mine workings. Low pH (as low as 3.2) and elevated concentrations of zinc, lead, cadmium, copper, and manganese (commonly exceeding water-quality standards for Elk Creek) were measured in samples located within or immediately downgradient of areas where sulfides are abundant, including the Standard fault, the Elk Lode portal, and the breccia pipe in Redwell Basin. Concentrations of these metals were typically low and pH values were circumneutral at surrounding locations. Metal concentrations in samples collected from underground workings in the Standard Mine were also generally higher than in samples collected at aboveground sites located outside of sulfide-rich areas. Metal concentrations in discharge from the Level 1 tunnel were among the highest measured in Elk Basin. All of these observations suggest that sulfide-rich mineralized rock is the primary control on dissolved metal concentrations and pH in ground water in the Standard Mine vicinity. Waste-rock piles apparently exert another major control on metal concentrations and pH; the lowest pH and highest metal concentrations typically are found in discharge from waste-rock piles. Concentrations of several chemical constituents along with strontium isotope data indicate that none of the sampled waters could have been the primary source of metals in discharge from Level 1. Therefore, this study did not identify the primary source location for metals in Level 1 discharge. Possible sources must be located below Levels 3 and 5 or farther back into the mountainside than the ends of Levels 3 and 5. Apparent tritium/helium-3 ground-water ages ranged from 0 to 9 yr, and a considerable majority were <1 yr. Tritium data and computed initial tritium values (measured tritium plus measured tritiogenic helium-3) suggest that much of the ground water in the Standard Mine vicinity was weeks to months old rather than years old. Tritium, d2H, and d18O data from water entering into and discharging from the Standard Mine displayed spatial and temporal patterns indicating that these tracers were influenced by seasonal variations in their concentration in precipitation. The tracer data therefore suggest that ground water entering into and discharging from the Standard Mine was largely composed of water <1 yr old. Pronounced seasonal variations in geochemistry in Level 1 discharge also are consistent with short r

Influence of the Roof Movement Control Method on the Stability of Remnant

NASA Astrophysics Data System (ADS)

Adach-Pawelus, Karolina

2017-12-01

In the underground mines, there are geological and mining situations that necessitate leaving behind remnants in the mining field. Remnants, in the form of small, irregular parcels, are usually separated in the case of: significant problems with maintaining roof stability, high rockburst hazard, the occurrence of complex geological conditions and for random reasons (ore remnants), as well as for economic reasons (undisturbed rock remnants). Remnants left in the mining field become sites of high stress values concentration and may affect the rock in their vicinity. The values of stress inside the remnant and its vicinity, as well as the stability of the remnant, largely depend on the roof movement control method used in the mining field. The article presents the results of the numerical analysis of the influence of roof movement control method on remnant stability and the geomechanical situation in the mining field. The numerical analysis was conducted for the geological and mining conditions characteristic of Polish underground copper mines owned by KGHM Polska Miedz S.A. Numerical simulations were performed in a plane strain state by means of Phase 2 v. 8.0 software, based on the finite element method. The behaviour of remnant and rock mass in its vicinity was simulated in the subsequent steps of the room and pillar mining system for three types of roof movement control method: roof deflection, dry backfill and hydraulic backfill. The parameters of the rock mass accepted for numerical modelling were calculated by means of RocLab software on the basis of the Hoek-Brown classification. The Mohr-Coulomb strength criterion was applied.

Mining influence on underground water resources in arid and semiarid regions

NASA Astrophysics Data System (ADS)

Luo, A. K.; Hou, Y.; Hu, X. Y.

2018-02-01

Coordinated mining of coal and water resources in arid and semiarid regions has traditionally become a focus issue. The research takes Energy and Chemical Base in Northern Shaanxi as an example, and conducts statistical analysis on coal yield and drainage volume from several large-scale mines in the mining area. Meanwhile, research determines average water volume per ton coal, and calculates four typical years’ drainage volume in different mining intensity. Then during mining drainage, with the combination of precipitation observation data in recent two decades and water level data from observation well, the calculation of groundwater table, precipitation infiltration recharge, and evaporation capacity are performed. Moreover, the research analyzes the transforming relationship between surface water, mine water, and groundwater. The result shows that the main reason for reduction of water resources quantity and transforming relationship between surface water, groundwater, and mine water is massive mine drainage, which is caused by large-scale coal mining in the research area.

Anchoring of development workings in a zone of influence of mining in case of the level anchoring system

NASA Astrophysics Data System (ADS)

Demin, V. F.; Fofanov, O. B.; Demina, T. V.; Yavorskiy, V. V.

2017-02-01

Regularities of the change of the stress-strain state of coal containing rock masses, depending on mining-geological factors, were revealed. These factors allow establishing rational parameters of anchoring of wall rocks to enhance the stability of development workings. Specific conditions of the deflected mode, displays of rock pressure, terms of maintenance depending on technological parameters are investigated. Researches allowed determining the degree of their development influence on the efficiency of application of the anchoring of the hollow making and will allow a reasonable application of anchoring certificates, provide stability of the rocks mining and reduce expenses on its realization and maintenance.

Effects of sediment discharge from Namibian diamond mines on intertidal and subtidal rocky-reef communities and the rock lobster Jasus lalandii

NASA Astrophysics Data System (ADS)

Pulfrich, Andrea; Branch, George M.

2014-10-01

Extensive terrestrial diamond mining occurs on the southern coast of Namibia, and at Elizabeth Bay near Lüderitz sediment tailings totalling about 2 million tons.yr-1, have been discharged onto the beach. We report here on monitoring spanning 2004-2012 to assess (1) the impacts of increased tailings discharges following an expansion of the mine in 2005, and (2) recovery after discharges halted in 2009. Sampling covered three levels of wave exposure, and compared impacted sites with comparable unmined reference sites. Benthic communities were quantified on both intertidal and subtidal reefs, and kelp densities and rock-lobster abundances, lengths and sex ratios on subtidal reefs. Prior to intensification of mining, deposition of tailings significantly influenced intertidal communities only at sheltered localities where wave action was insufficient to disperse them. Following the mine expansion, effects spread to both semi-exposed and exposed sites. After mining was suspended, recovery of the biota was limited, even three years later. Reductions of intertidal diversity and grazers, proliferation of macroalgae, and increased dominance by filter feeders were recorded at the impacted sites and were persistent, but the affects of wave exposure on community composition generally exceeded those of mining discharges. On subtidal reefs, tailings deposition reduced predators and grazers, increased filter feeders and ephemeral green algae, and decreased all other algae, possibly driven by light reduction due to plumes of suspended fine sediments. Increased discharges post-2005 also substantially influenced bathymetry, wave and current regimes, transforming 2 km of previously wave-exposed rocky coastline into a semi-exposed sandy beach. Tailings discharge appeared to influence community composition in four ways: (1) inundation and blanketing; (2) increased suspended particulate materials; (3) indirect top-down ripple effects, and (4) light reduction. Throughout the period 2004-2007, tailings-deposition had no detectable effects on the sex ratio, sizes or density of rock lobsters, but following suspension of mining activities, densities in 2010-2012 at impact sites exceeded those at reference sites. High natural variability in the abundance of rock lobsters may mask mining impacts, but the data strongly indicate an absence of any negative effects on rock lobsters.

Modeling of information on the impact of mining exploitation on bridge objects in BIM

NASA Astrophysics Data System (ADS)

Bętkowski, Piotr

2018-04-01

The article discusses the advantages of BIM (Building Information Modeling) technology in the management of bridge infrastructure on mining areas. The article shows the problems with information flow in the case of bridge objects located on mining areas and the advantages of proper information management, e.g. the possibility of automatic monitoring of structures, improvement of safety, optimization of maintenance activities, cost reduction of damage removal and preventive actions, improvement of atmosphere for mining exploitation, improvement of the relationship between the manager of the bridge and the mine. Traditional model of managing bridge objects on mining areas has many disadvantages, which are discussed in this article. These disadvantages include among others: duplication of information about the object, lack of correlation in investments due to lack of information flow between bridge manager and mine, limited assessment possibilities of damage propagation on technical condition and construction resistance to mining influences.

Design of foundations with sliding joint at areas affected with underground mining

NASA Astrophysics Data System (ADS)

Matečková, P.; Šmiřáková, M.; Maňásek, P.

2018-04-01

Underground mining always influences also landscape on surface. If there are buildings on the surface they are affected with terrain deformation which comprises terrain inclination, curvature, shift and horizontal deformation. Ostrava – Karvina region is specific with underground mining very close to densely inhabited area. About 25 years ago there were mines even in the city of Ostrava. Recommendations and rules for design of building structures at areas affected with underground mining have been therefore analysed in long term. This paper is focused on deformation action caused by terrain horizontal deformation - expansion or compression. Through the friction between foundation structure and subsoil in footing bottom the foundation structure has to resist significant normal forces. The idea of sliding joint which eliminates the friction and decreases internal forces comes from the last century. Sliding joint made of asphalt belt has been analysed at Faculty of Civil Engineering, VSB – Technical University of Ostrava in long term. The influence of vertical and horizontal load and the effect of temperature in temperature controlled room have been examined. Testing, design and utilization of sliding joint is presented.

Application of multivariate analysis to investigate the trace element contamination in top soil of coal mining district in Jorong, South Kalimantan, Indonesia

NASA Astrophysics Data System (ADS)

Pujiwati, Arie; Nakamura, K.; Watanabe, N.; Komai, T.

2018-02-01

Multivariate analysis is applied to investigate geochemistry of several trace elements in top soils and their relation with the contamination source as the influence of coal mines in Jorong, South Kalimantan. Total concentration of Cd, V, Co, Ni, Cr, Zn, As, Pb, Sb, Cu and Ba was determined in 20 soil samples by the bulk analysis. Pearson correlation is applied to specify the linear correlation among the elements. Principal Component Analysis (PCA) and Cluster Analysis (CA) were applied to observe the classification of trace elements and contamination sources. The results suggest that contamination loading is contributed by Cr, Cu, Ni, Zn, As, and Pb. The elemental loading mostly affects the non-coal mining area, for instances the area near settlement and agricultural land use. Moreover, the contamination source is classified into the areas that are influenced by the coal mining activity, the agricultural types, and the river mixing zone. Multivariate analysis could elucidate the elemental loading and the contamination sources of trace elements in the vicinity of coal mine area.

Influence of the Typha community on mine drainage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Snyder, C.D.; Aharrah, E.C.

1984-12-01

This study investigated potential positive influences of the Typha community on mine drainage. The pH increased as the water flowed through two, two-pond systems, and the iron and manganese concentrations decreased. The water quality remained constant or deteriorated in non-vegetated ponds. Typha from the ponds and a non-mined site were assayed for iron and manganese. Roots/rhizomes concentrated the most iron, while the exterior stem layers contained more iron than the remaining stems or leaves. Manganese concentrations were similar in the roots/rhizomes, the leaves, and the exterior stem layers, while stems contained less. Iron concentrations in the Typha from June andmore » September were similar, but manganese concentrations in these Typha were different. Typha from mined sites accumulated more iron and manganese in the roots/rhizomes than Typha from non-mined sites. Bacteria and algae were identified and numerous species which function as oxidizers were recorded. These microbes play an important role in the Typha community and should also be considered in future studies as agents in the removal of metallic ions.« less

Analysis 320 coal mine accidents using structural equation modeling with unsafe conditions of the rules and regulations as exogenous variables.

PubMed

Zhang, Yingyu; Shao, Wei; Zhang, Mengjia; Li, Hejun; Yin, Shijiu; Xu, Yingjun

2016-07-01

Mining has been historically considered as a naturally high-risk industry worldwide. Deaths caused by coal mine accidents are more than the sum of all other accidents in China. Statistics of 320 coal mine accidents in Shandong province show that all accidents contain indicators of "unsafe conditions of the rules and regulations" with a frequency of 1590, accounting for 74.3% of the total frequency of 2140. "Unsafe behaviors of the operator" is another important contributory factor, which mainly includes "operator error" and "venturing into dangerous places." A systems analysis approach was applied by using structural equation modeling (SEM) to examine the interactions between the contributory factors of coal mine accidents. The analysis of results leads to three conclusions. (i) "Unsafe conditions of the rules and regulations," affect the "unsafe behaviors of the operator," "unsafe conditions of the equipment," and "unsafe conditions of the environment." (ii) The three influencing factors of coal mine accidents (with the frequency of effect relation in descending order) are "lack of safety education and training," "rules and regulations of safety production responsibility," and "rules and regulations of supervision and inspection." (iii) The three influenced factors (with the frequency in descending order) of coal mine accidents are "venturing into dangerous places," "poor workplace environment," and "operator error." Copyright © 2016 Elsevier Ltd. All rights reserved.

On Interestingness Measures for Mining Statistically Significant and Novel Clinical Associations from EMRs

PubMed Central

Abar, Orhan; Charnigo, Richard J.; Rayapati, Abner

2017-01-01

Association rule mining has received significant attention from both the data mining and machine learning communities. While data mining researchers focus more on designing efficient algorithms to mine rules from large datasets, the learning community has explored applications of rule mining to classification. A major problem with rule mining algorithms is the explosion of rules even for moderate sized datasets making it very difficult for end users to identify both statistically significant and potentially novel rules that could lead to interesting new insights and hypotheses. Researchers have proposed many domain independent interestingness measures using which, one can rank the rules and potentially glean useful rules from the top ranked ones. However, these measures have not been fully explored for rule mining in clinical datasets owing to the relatively large sizes of the datasets often encountered in healthcare and also due to limited access to domain experts for review/analysis. In this paper, using an electronic medical record (EMR) dataset of diagnoses and medications from over three million patient visits to the University of Kentucky medical center and affiliated clinics, we conduct a thorough evaluation of dozens of interestingness measures proposed in data mining literature, including some new composite measures. Using cumulative relevance metrics from information retrieval, we compare these interestingness measures against human judgments obtained from a practicing psychiatrist for association rules involving the depressive disorders class as the consequent. Our results not only surface new interesting associations for depressive disorders but also indicate classes of interestingness measures that weight rule novelty and statistical strength in contrasting ways, offering new insights for end users in identifying interesting rules. PMID:28736771

Measurement and modeling of transfer functions for lightning coupling into the Sago mine.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morris, Marvin E.; Higgins, Matthew B.

2007-04-01

This report documents measurements and analytical modeling of electromagnetic transfer functions to quantify the ability of cloud-to-ground lightning strokes (including horizontal arc-channel components) to couple electromagnetic energy into the Sago mine located near Buckhannon, WV. Two coupling mechanisms were measured: direct and indirect drive. These transfer functions are then used to predict electric fields within the mine and induced voltages on conductors that were left abandoned in the sealed area of the Sago mine.

[Evaluation of environmental conditions: air, water and soil in areas of mining activity in Boyacá, Colombia].

PubMed

Agudelo-Calderón, Carlos A; Quiroz-Arcentales, Leonardo; García-Ubaque, Juan C; Robledo-Martínez, Rocío; García-Ubaque, Cesar A

2016-02-01

Objectives To determine concentrations of PM10, mercury and lead in indoor air of homes, water sources and soil in municipalities near mining operations. Method 6 points were evaluated in areas of influence and 2 in control areas. For measurements of indoor air, we used the NIOSH 600 method (PM10), NIOSH 6009 (mercury) and NIOSH 7300 (lead). For water analysis we used the IDEAM Guide for monitoring discharges. For soil analysis, we used the cold vapor technique (mercury) and atomic absorption (lead). Results In almost all selected households, the average PM10 and mercury concentrations in indoor air exceeded applicable air quality standards. Concentrations of lead were below standard levels. In all water sources, high concentrations of lead were found and in some places within the mining areas, high levels of iron, aluminum and mercury were also found. In soil, mercury concentrations were below the detection level and for lead, differences between the monitored points were observed. Conclusions The results do not establish causal relationships between mining and concentration of these pollutants in the evaluated areas because of the multiplicity of sources in the area. However, such studies provide important information, useful to agents of the environmental health system and researchers. Installation of networks for environmental monitoring to obtain continuous reports is suggested.

Porites corals as recorders of mining and environmental impacts: Misima Island, Papua New Guinea

NASA Astrophysics Data System (ADS)

Fallon, Stewart J.; White, Jamie C.; McCulloch, Malcolm T.

2002-01-01

In 1989 open-cut gold mining commenced on Misima Island in Papua New Guinea (PNG). Open-cut mining by its nature causes a significant increase in sedimentation via the exposure of soils to the erosive forces of rain and runoff. This increased sedimentation affected the nearby fringing coral reef to varying degrees, ranging from coral mortality (smothering) to relatively minor short-term impacts. The sediment associated with the mining operation consists of weathered quartz feldspar, greenstone, and schist. These rocks have distinct chemical characteristics (rare earth element patterns and high abundances of manganese, zinc, and lead) and are entering the near-shore environment in considerably higher than normal concentrations. Using laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), we analyzed eight colonies (two from high sedimentation, two transitional, two minor, and two unaffected control sites) for Y, La, Ce, Mn, Zn, and Pb. All sites show low steady background levels prior to the commencement of mining in 1988. Subsequently, all sites apart from the control show dramatic increases of Y, La, and Ce associated with the increased sedimentation as well as rapid decreases following the cessation of mining. The elements Zn and Pb exhibit a different behavior, increasing in concentration after 1989 when ore processing began and one year after initial mining operations. Elevated levels of Zn and Pb in corals has continued well after the cessation of mining, indicating ongoing transport into the reef of these metals via sulfate-rich waters. Rare earth element (REE) abundance patterns measured in two corals show significant differences compared to Coral Sea seawater. The corals display enrichments in the light and middle REEs while the heavy REEs are depleted relative to the seawater pattern. This suggests that the nearshore seawater REE pattern is dominated by island sedimentation. Trace element abundances of Misima Island corals clearly record the dramatic changes in the environmental conditions at this site and provide a basis for identifying anthropogenic influences on corals reefs.

Acid mine drainage pollution in the Tinto and Odiel rivers (Iberian Pyrite Belt, SW Spain) and bioavailability of the transported metals to the Huelva Estuary.

PubMed

Nieto, José Miguel; Sarmiento, Aguasanta M; Olías, Manuel; Canovas, Carlos R; Riba, Inmaculada; Kalman, Judit; Delvalls, T Angel

2007-05-01

The Tinto and Odiel rivers are seriously affected by acid mine drainage (AMD) from the long-term mining activities in Iberian Pyrite Belt (IPB). As a consequence, the Huelva estuary is heavily contaminated by metals and metalloids. This study presents an estimation of the seasonal variation, and the dissolved contaminant load transported by both rivers from February 2002 to September 2004. Besides, toxicity and bioaccumulation tests with the sediments of the estuary have been conducted in order to measure the mobility of the toxic metals. Results show that the Tinto and Odiel rivers transport enormous quantities of dissolved metals to the estuary: 7900 t yr(-1) of Iron (Fe), 5800 t yr(-1) Aluminium (Al), 3500 t yr(-1) Zinc (Zn), 1700 t yr(-1) Copper (Cu), 1600 t yr(-1) Manganese (Mn) and minor quantities of other metals and metalloids. These values represent 37% of the global gross flux of dissolved Zn transported by rivers in to the ocean, and 15% of the global gross flux of dissolved Cu. These metals and metalloids usually sink in the estuarine sediments due to pH and salinity changes. The increase of salinity in the estuary favours the adsorption and trapping of metals. For this reason, the mobility and bioavailability of metals such as Zn, Cd and Cu is higher in sediments located in the area of fresh water influence that in sediments located in the marine influenced area of the estuary, showing a higher percentage of fractionation and bioaccumulation of these metals in the station influenced by the fresh water environment.

Government regulation of occupational safety: underground coal mine accidents 1973-75.

PubMed Central

Boden, L I

1985-01-01

The purpose of this paper is to determine the influence of federal mine safety inspections on underground coal mine accidents. An economic incentives model is developed to relate federal enforcement activities to accident rates. The determinants of accident rates are analyzed for 535 coal mines during the period 1973-75. Estimates based on these data when applied to the model indicate that increasing inspections by 25 per cent would have produced a 13 per cent decline in fatal accidents and an 18 per cent decline in disabling accidents. PMID:3985237

Government regulation of occupational safety: underground coal mine accidents 1973-75.

PubMed

Boden, L I

1985-05-01

The purpose of this paper is to determine the influence of federal mine safety inspections on underground coal mine accidents. An economic incentives model is developed to relate federal enforcement activities to accident rates. The determinants of accident rates are analyzed for 535 coal mines during the period 1973-75. Estimates based on these data when applied to the model indicate that increasing inspections by 25 per cent would have produced a 13 per cent decline in fatal accidents and an 18 per cent decline in disabling accidents.

Quantification of the inevitable: the influence of soil macrofauna on soil water movement in rehabilitated open-cut mine land

NASA Astrophysics Data System (ADS)

Arnold, S.; Williams, E. R.

2015-08-01

Recolonisation of soil by macrofauna (especially ants and termites) in rehabilitated open-cut mine sites is inevitable. In these highly disturbed landscapes, soil invertebrates play a major role in soil development (macropore configuration, nutrient cycling, bioturbation, etc.) and can influence hydrological processes such as infiltration and seepage. Understanding and quantifying these ecosystem processes is important in rehabilitation design, establishment and subsequent management to ensure progress to the desired end-goal, especially in waste cover systems designed to prevent water reaching and transporting underlying hazardous waste materials. However, soil macrofauna are typically overlooked during hydrological modelling, possibly due to uncertainties on the extent of their influence, which can lead to failure of waste cover systems or rehabilitation activities. We propose that scientific experiments under controlled conditions are required to quantify (i) macrofauna - soil structure interactions, (ii) functional dynamics of macrofauna taxa, and (iii) their effects on macrofauna and soil development over time. Such knowledge would provide crucial information for soil water models, which would increase confidence in mine waste cover design recommendations and eventually lead to higher likelihood of rehabilitation success of open-cut mining land.

[Spatial distribution and ecological significance of heavy metals in soils from Chatian mercury mining deposit, western Hunan province].

PubMed

Sun, Hong-Fei; Li, Yong-Hu; Ji, Yan-Fang; Yang, Lin-Sheng; Wang, Wu-Yi

2009-04-15

Ores, waste tailings and slag, together with three typical soil profiles (natural soil profiles far from mine entrance and near mine entrance, soil profile under slag) in Chatian mercury mining deposit (CMD), western Hunan province were sampled and their concentrations of mercury (Hg), arsenic (As), lead (Pb), cadmium (Cd), zinc (Zn) were determined by HG-ICP-AES and ICP-MS. Enrichment factor and correlation analysis were taken to investigate the origins, distribution and migration of Hg, as well as other heavy metals in the CMD. The results show that Hg is enriched in the bottom of the soil profile far from mine entrance but accumulated in the surface of soil profiles near mine entrance and under slag. The soil profiles near mine entrance and under slag are both contaminated by Hg, while the latter is contaminated more heavily. In the soil profile under slag, Hg concentration in the surface soil, Hg average concentration in the total profile, and the leaching depth of soil Hg are 640 microg x g(-1), (76.74 +/- 171.71) microg x g(-1), and more than 100 cm, respectively; while 6.5 microg x g(-1), (2.74 +/- 1.90) microg x g(-1), and 40 cm, respectively, are found in the soil profile near mine entrance. Soil in the mercury mine area is also polluted by Cd, As, Pb, Zn besides metallogenic element Hg, among which Cd pollution is relatively heavier than others. The mobility of the studied heavy metals in soil follows the order as Hg > Cd > As > Zn approximately equal to Pb. The leaching depth of the heavy metals is influenced by total concentration in the surface soil and soil physico-chemical parameters. The origins, distribution and migration of heavy metals in soil profile in the mining area are related to primary geological environment, and strongly influenced by human mining activities.

Ask and Ye Shall Receive? Automated Text Mining of Michigan Capital Facility Finance Bond Election Proposals to Identify Which Topics Are Associated with Bond Passage and Voter Turnout

ERIC Educational Resources Information Center

Bowers, Alex J.; Chen, Jingjing

2015-01-01

The purpose of this study is to bring together recent innovations in the research literature around school district capital facility finance, municipal bond elections, statistical models of conditional time-varying outcomes, and data mining algorithms for automated text mining of election ballot proposals to examine the factors that influence the…

[Effect of vibration, noise, physical exertion and unfavorable microclimate on carbohydrate metabolism in workers engaged into mining industry and machine building].

PubMed

Lapko, I V; Kir'iakov, V A; Antoshina, L I; Pavlovskaia, N A; Kondratovich, S V

2014-01-01

The authors studied influence of vibration, noise, physical overexertion and microclimate on carbohydrates metabolism and insulin resistance in metal mining industry workers. Findings are that vibration disease appeared to have maximal effect on insulin resistance test results and insulin level. The authors suggested biomarkers for early diagnosis of insulin resistance disorders in metal mining industry workers.

Stability of highwalls in surface coal mines, western Powder Ridge Basin, Wyoming and Montana

USGS Publications Warehouse

Lee, Fitzhugh T.; Smith, William K.; Savage, William Z.

1976-01-01

Preliminary results from the first part of a two-part investigation of the stability of highwalls in open-pit coal mines in the Fort Union Formation of the western Powder River Basin of Wyoming and Montana indicate that these highwalls are subject to time-dependent deformation. Field investigations and laboratory physical-properties tests of coal and overburden rocks suggest that several factors influence highwall stability. Some of these factors are rebound of overconsolidated rocks, desiccation, water, orientation and spacing of fractures, and strength and deformation properties. Factors of safety for a typical highwall in the study area (calculated by the finite-element method) may be less than 1.0 when open fractures are present and the highwall has degraded. Although it is concluded that most open-pit mines in the Fort Union Formation within the study area have generally stable highwalls, these highwalls do deteriorate and become progressively less stable. Because of this, postmining failures are common and could be critical if mining were delayed and then resumed after a period of several months. The second part of the investigation will utilize field measurements of rock-mass properties and instrumentation of actively mined highwalls to obtain data for comparison with the results of the initial investigation. Because the height of highwalls will increase as the more shallow coal is exhausted, these data will also be used to predict the behavior of slopes higher than those presently found in the western Powder River Basin.

Coal availability in the Hilight Quadrangle, Powder River Basin, Wyoming; a prototype study in a western coal field

USGS Publications Warehouse

Molnia, Carol L.; Biewick, Laura; Blake, Dorsey; Tewalt, Susan J.; Carter, M. Devereaux; Gaskill, Charlie

1997-01-01

The U.S. Geological Survey (USGS), in cooperation with the Bureau of Land Management (BLM), Geological Survey of Wyoming, and U.S. Bureau of Mines (USBM), has produced an estimate of the amount of available coal in an area about 35 miles south of Gillette, Wyo., where the Wyodak coal bed is, in places, more than 100 ft thick. Available coal is the quantity of the total coal resource that is accessible for mine development under current regulatory, land-use, and technologic constraints. This first western coal availability study, of the Hilight 7 1/2-minute quadrangle, indicates that approximately 60 percent (2.7 billion short tons) of the total 4.4 billion tons of coal in-place in the quadrangle is available for development. (There has been no commercial mining in the Hilight quadrangle.) Approximately 67 percent (1.9 billion tons) of the Main Wyodak coal bed is considered available. All tonnage measurements in this report are given in short tons. Coal-development considerations in the quadrangle include dwellings, railroads, pipelines, power lines, wildlife habitat (eagles), alluvial valley floors, cemeteries, and the Hilight oil and gas field and gas plant. Some of these considerations could be mitigated so that surface mining of the coal may proceed; others could not be mitigated and would preclude mining in their vicinity. Other technological constraints that influence the availability of the coal include overburden thickness, coal beds too thin, and areas of clinker.

The influence of geomorphology on the role of women at artisanal and small-scale mine sites

USGS Publications Warehouse

Malpeli, Katherine C.; Chirico, Peter G.

2013-01-01

The geologic and geomorphic expressions of a mineral deposit determine its location, size, and accessibility, characteristics which in turn greatly influence the success of artisans mining the deposit. Despite this critical information, which can be garnered through studying the surficial physical expression of a deposit, the geologic and geomorphic sciences have been largely overlooked in artisanal mining-related research. This study demonstrates that a correlation exists between the roles of female miners at artisanal diamond and gold mining sites in western and central Africa and the physical expression of the deposits. Typically, women perform ore processing and ancillary roles at mine sites. On occasion, however, women participate in the extraction process itself. Women were found to participate in the extraction of ore only when a deposit had a thin overburden layer, thus rendering the mineralized ore more accessible. When deposits required a significant degree of manual labour to access the ore due to thick overburden layers, women were typically relegated to other roles. The identification of this link encourages the establishment of an alternative research avenue in which the physical and social sciences merge to better inform policymakers, so that the most appropriate artisanal mining assistance programs can be developed and implemented.

Matrix Intensification Alters Avian Functional Group Composition in Adjacent Rainforest Fragments

PubMed Central

Deikumah, Justus P.; McAlpine, Clive A.; Maron, Martine

2013-01-01

Conversion of farmland land-use matrices to surface mining is an increasing threat to the habitat quality of forest remnants and their constituent biota, with consequences for ecosystem functionality. We evaluated the effects of matrix type on bird community composition and the abundance and evenness within avian functional groups in south-west Ghana. We hypothesized that surface mining near remnants may result in a shift in functional composition of avifaunal communities, potentially disrupting ecological processes within tropical forest ecosystems. Matrix intensification and proximity to the remnant edge strongly influenced the abundance of members of several functional guilds. Obligate frugivores, strict terrestrial insectivores, lower and upper strata birds, and insect gleaners were most negatively affected by adjacent mining matrices, suggesting certain ecosystem processes such as seed dispersal may be disrupted by landscape change in this region. Evenness of these functional guilds was also lower in remnants adjacent to surface mining, regardless of the distance from remnant edge, with the exception of strict terrestrial insectivores. These shifts suggest matrix intensification can influence avian functional group composition and related ecosystem-level processes in adjacent forest remnants. The management of matrix habitat quality near and within mine concessions is important for improving efforts to preserveavian biodiversity in landscapes undergoing intensification such as through increased surface mining. PMID:24058634

The synergic role of sociotechnical and personal characteristics on work injuries in mines.

PubMed

Paul, P S; Maiti, J

2008-05-01

Occupational injuries in mines are attributed to many factors. In this study, an attempt was made to identify the various factors related to work injuries in mines and to estimate their effects on work injuries to mine workers. An accident path model was developed to estimate the pattern and strength of relationships amongst the personal and sociotechnical variables in accident/injury occurrences. The input data for the model were the correlation matrix of 18 variables, which were collected from the case study mines. The case study results showed that there are sequential interactions amongst the sociotechnical and personal factors leading to accidents/injuries in mines. Amongst the latent endogenous constructs, job dissatisfaction and safe work behaviour show a significant positive and negative direct relationship with work injury, respectively. However, the construct safety environment has a significant negative indirect relationship with work injury. The safety environment is negatively affected by work hazards and positively affected by social support. The safety environment also shows a significant negative relationship with job stress and job dissatisfaction. However, negative personality has no significant direct or indirect effect on work injury, but it has a significant negative relationship with safe work behaviour. The endogenous construct negative personality is positively influenced by job stress and negatively influenced by social support.

Matrix intensification alters avian functional group composition in adjacent rainforest fragments.

PubMed

Deikumah, Justus P; McAlpine, Clive A; Maron, Martine

2013-01-01

Conversion of farmland land-use matrices to surface mining is an increasing threat to the habitat quality of forest remnants and their constituent biota, with consequences for ecosystem functionality. We evaluated the effects of matrix type on bird community composition and the abundance and evenness within avian functional groups in south-west Ghana. We hypothesized that surface mining near remnants may result in a shift in functional composition of avifaunal communities, potentially disrupting ecological processes within tropical forest ecosystems. Matrix intensification and proximity to the remnant edge strongly influenced the abundance of members of several functional guilds. Obligate frugivores, strict terrestrial insectivores, lower and upper strata birds, and insect gleaners were most negatively affected by adjacent mining matrices, suggesting certain ecosystem processes such as seed dispersal may be disrupted by landscape change in this region. Evenness of these functional guilds was also lower in remnants adjacent to surface mining, regardless of the distance from remnant edge, with the exception of strict terrestrial insectivores. These shifts suggest matrix intensification can influence avian functional group composition and related ecosystem-level processes in adjacent forest remnants. The management of matrix habitat quality near and within mine concessions is important for improving efforts to preserveavian biodiversity in landscapes undergoing intensification such as through increased surface mining.

Ground penetrating radar coal measurements demonstration at the U.S. Bureau of Mines Research Center, Pittsburgh, Pennsylvania. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gardner, D.; Guerrier, J.; Martinez, M.

1994-01-04

In situ and near real-time measurements of coal seam thickness have been identified by industry as a highly desirable component of robotic mining systems. With it, a continuous mining machine can be guided close to the varying boundary of the seam while the cutting operation is underway. This provides the mining operation the ability to leave behind the high-sulfur, high-particulate coal which is concentrated near the seam boundary. The result is near total recovery of high quality coal resources, an increase in mining efficiency, and opportunities for improved safety through reduction in personnel in the most hazardous coal cutting areas.more » In situ, real-time coal seam measurements using the Special Technologies Laboratory (STL) ground penetrating radar (GPR) technology were shown feasible by a demonstration in a Utah coal mine on April 21, 1994. This report describes the October 18, 1994 in situ GPR measurements of coal seam thickness at the US Bureau of Mines (USBM) robotic mining testing laboratory. In this report, an overview of the measurements at the USBM Laboratory is given. It is followed by a description of the technical aspects of the STL frequency modulated-continuous wave (FM-CW) GPR system. Section 4 provides a detailed description of the USBM Laboratory measurements and the conditions under which they were taken. Section 5 offers conclusions and possibilities for future communications.« less

Invited Article: In situ comparison of passive radon-thoron discriminative monitors at subsurface workplaces in Hungary

NASA Astrophysics Data System (ADS)

Kávási, Norbert; Vigh, Tamás; Németh, Csaba; Ishikawa, Tetsuo; Omori, Yasutaka; Janik, Miroslaw; Yonehara, Hidenori

2014-02-01

During a one-year long measurement period, radon and thoron data obtained by two different passive radon-thoron discriminative monitors were compared at subsurface workplaces in Hungary, such as mines (bauxite and manganese ore) and caves (medical and touristic). These workplaces have special environmental conditions, such as, stable and high relative humidity (100%), relatively stable temperature (12°C-21°C), low or high wind speed (max. 2.4 m s-1) and low or elevated aerosol concentration (130-60 000 particles m-3). The measured radon and thoron concentrations fluctuated in a wide range among the different workplaces. The respective annual average radon concentrations and their standard deviations (in brackets) measured by the passive radon-thoron discriminative monitor with cellulose filter (CF) and the passive radon-thoron discriminative monitor with sponge filter (SF) were: 350(321) Bq m-3 and 550(497) Bq m-3 in the bauxite mine; 887(604) Bq m-3 and 1258(788) Bq m-3 in the manganese ore mine; 2510(2341) Bq m-3 and 3403(3075) Bq m-3 in the medical cave (Hospital Cave of Tapolca); and 6239(2057) Bq m-3 and 8512(1955) Bq m-3 in the touristic cave (Lake Cave of Tapolca). The respective average thoron concentrations and their standard deviation (in brackets) measured by CF and SF monitors were: 154(210) Bq m-3 and 161(148) Bq m-3 in the bauxite mine; 187(191) Bq m-3 and 117(147) Bq m-3 in the manganese-ore mine; 360(524) Bq m-3 and 371(789) Bq m-3 in the medical cave (Hospital Cave of Tapolca); and 1420(1184) Bq m-3 and 1462(3655) Bq m-3 in the touristic cave (Lake Cave of Tapolca). Under these circumstances, comparison of the radon data for the SF and CF monitors showed the former were consistently 51% higher in the bauxite mine, 38% higher in the manganese ore mine, and 34% higher in the caves. Consequently, correction is required on previously obtained radon data acquired by CF monitors at subsurface workplaces to gain comparable data for SF monitors. In the case of thoron, the data were unreliable and no significant tendency was seen during the comparison therefore comparison of previously obtained thoron data acquired by either CF or SF is doubtful. There was probable influence by relative humidity on the detection response; however, the effects of the high wind speed and elevated aerosol concentration could not be excluded. The results of this study call attention to the importance of calibration under extreme environmental conditions and the need for using reliable radon-thoron monitors for subsurface workplaces.

A study of acid and ferruginous mine water in coal mining operations

NASA Astrophysics Data System (ADS)

Atkins, A. S.; Singh, R. N.

1982-06-01

The paper describes a bio-chemical investigation in the laboratory to identify various factors which promote the formation of acidic and ferruginous mine water. Biochemical reactions responsible for bacterial oxidation of Iron pyrites are described. The acidic and ferruginous mine water are not only responsible for the corrosion of mine plant and equipment and formation of scales in the delivery pipe range, but also pollution of the mine surface environment, thus affecting the surface ecology. Control measures to mitigate the adverse effects of acid mine discharge include the protection of mining equipment and prevention of formation of acid and ferruginous water. Various control measures discussed in the paper are blending with alkaline or spring water, use of neutralising agents and bactericides, and various types of seals for preventing water and air coming into contact with pyrites in caved mine workings.

Exposure assessment of heavy metals on abandoned metal mine areas by ingestion of soil, crop plant and groundwater

NASA Astrophysics Data System (ADS)

Lee, J.-S.; Chon, H.-T.

2003-05-01

In order to assess the risk of adverse health effects on human exposure to arsenic and heavy metals influence by past mining activities, environmental geochemical survey was undertaken in the abandoned metal mine areas (Dongil Au-Ag-Cu-Zn mine, Okdong Cu-Pb-Zn mine, Myungbong Au-Ag mine). Arsenic and other heavy metals were highly elevated in the tailings from the Dongil mine (8,720 As mg/kg, 5.9 Cd mg/kg, 3,610 Cu mg/kg, 5,850 Pb mg/kg, 630 Zn mg/kg). Heavy metals except As from the Okdong mine (53.6 Cd mg/kg, 910 Cu mg/kg, 1,590 Pb mg/kg, 5,720 Zn mg/kg) and As from the Myungbong mine (5,810 As mg/kg) were also elevated. Elevated levels of As, Cd and Zn were also found in agricultural soils from these mine areas. The H.I. (hazard index) values of As and Cd from the Dongil, the Okdong and Myungbong mine areas are higher than 1.0. Therefore, toxic risk for As and Cd exist via exposure (ingestion) of contaminated soil, groundwater and rice grain in these mine areas.

Coal mine bumps as related to geologic features in the northern part of the Sunnyside District, Carbon County, Utah

USGS Publications Warehouse

Osterwald, Frank W.; Dunrud, C. Richard; Collins, Donley S.

1993-01-01

Coal mine bumps, which are violent, spontaneous, and often catastrophic disruptions of coal and rock, were common in the Sunnyside coal mining district, Utah, before the introduction of protective-engineering methods, modern room-and-pillar retreat mining with continuous mining machines, and particularly modern longwall mining. The coal at Sunnyside, when stressed during mining, fails continuously with many popping, snapping, and banging noises. Although most of the bumps are beneficial because they make mining easier, many of the large ones are dangerous and in the past caused injuries and fatalities, particularly with room- and-pillar mining methods used in the early mining operations. Geologic mapping of underground mine openings revealed many types of deformational features, some pre-mine and some post-mine in age. Stresses resulting from mining are concentrated near the mine openings; if openings are driven at large angles to small pre-mine deformational features, particularly shatter zones in coal, abnormal stress buildups may occur and violent bumps may result. Other geologic features, such as ripple marks, oriented sand grains, intertongued rock contacts, trace fossils, and load casts, also influence the occurrence of bumps by impeding slip of coal and rocks along bedding planes. The stress field in the coal also varies markedly because of the rough ridge and canyon topography. These features may allow excessively large stress components to accumulate. At many places, the stresses that contribute to deformation and failures of mine openings are oriented horizontally. The stratigraphy of the rocks immediately above and below the mined coal bed strongly influences the deformation of the mine openings in response to stress accumulations. Triaxial compressive testing of coal from the Sunnyside No.1 and No.3 Mines indicates that the strength of the coal increases several times as the confining (lateral) stress is increased. Strengths of cores cut from single large blocks of coal vary widely. Although the strengths of coal cores increase slowly at high levels of confining stress, the coal in Sunnyside No. 1 Mine is slightly stronger in laboratory tests than coal in Sunnyside No.3 Mine. The coal in No.1 Mine probably can store larger amounts of stress than coal in the No.3 Mine, which may account for the apparently greater number of violent bumps in No.1 Mine. The strength of coal, and its ability to store stress before failure, may correlate in part with chemical composition, particularly with the amounts of benzene ring compounds in vitrain; coal with relatively large amounts of benzene ring compounds is stronger than coal with lesser amounts of these compounds. Alternatively, the chemical composition of coal may affect its response to stress. Increasing contents of kaolinite in coal appear to reduce its compressive strength at low confining stresses, resulting in easy failures of pillars and ribs in mine openings. Applications of the geologic factors outlined in this report, carefully coupled with advanced modern engineering methods, have markedly reduced the hazards from coal mine bumps and related failures of mine openings at Sunnyside. Similar studies probably could aid in reducing bump-related hazards in other coal mining areas.

Geochemical characterisation of seepage and drainage water quality from two sulphide mine tailings impoundments: Acid mine drainage versus neutral mine drainage

USGS Publications Warehouse

Heikkinen, P.M.; Raisanen, M.L.; Johnson, R.H.

2009-01-01

Seepage water and drainage water geochemistry (pH, EC, O2, redox, alkalinity, dissolved cations and trace metals, major anions, total element concentrations) were studied at two active sulphide mine tailings impoundments in Finland (the Hitura Ni mine and Luikonlahti Cu mine/talc processing plant). The data were used to assess the factors influencing tailings seepage quality and to identify constraints for water treatment. Changes in seepage water quality after equilibration with atmospheric conditions were evaluated based on geochemical modelling. At Luikonlahti, annual and seasonal changes were also studied. Seepage quality was largely influenced by the tailings mineralogy, and the serpentine-rich, low sulphide Hitura tailings produced neutral mine drainage with high Ni. In contrast, drainage from the high sulphide, multi-metal tailings of Luikonlahti represented typical acid mine drainage with elevated contents of Zn, Ni, Cu, and Co. Other factors affecting the seepage quality included weathering of the tailings along the seepage flow path, process water input, local hydrological settings, and structural changes in the tailings impoundment. Geochemical modelling showed that pH increased and some heavy metals were adsorbed to Fe precipitates after net alkaline waters equilibrated with the atmosphere. In the net acidic waters, pH decreased and no adsorption occurred. A combination of aerobic and anaerobic treatments is proposed for Hitura seepages to decrease the sulphate and metal loading. For Luikonlahti, prolonged monitoring of the seepage quality is suggested instead of treatment, since the water quality is still adjusting to recent modifications to the tailings impoundment.

Simultaneous selenate reduction and denitrification by a consortium of enriched mine site bacteria.

PubMed

Subedi, Gaurav; Taylor, Jon; Hatam, Ido; Baldwin, Susan A

2017-09-01

Increasing selenium concentrations in aquatic environments downstream of mine sites is of great concern due to selenium's bioaccumulation propensity and teratogenic toxicity. Removal of selenium from mine influenced water is complicated by the presence of nitrate, which is also elevated in mine influenced water due to the use of explosives in mining. In many biological treatment processes, nitrate as a thermodynamically more preferable electron acceptor inhibits selenate reduction. Here we report on an enrichment of a bacterial assemblage from a mine impacted natural marsh sediment that was capable of simultaneous selenate reduction and denitrification. Selenate reduction followed first order kinetics with respect to the concentration of total dissolved selenium. The kinetic rate constant was independent of initial nitrate concentration over the range 3-143 mg L -1 -NO 3 - -N. The initial concentration of selenate inhibited selenate reduction kinetics over the range 1-24 mg-Se L -1 . Dominant taxa that grew in selenate only medium were classified in the genera Pseudomonas, Lysinibacillus and Thauera. When nitrate was introduced in addition to selenate, previously rare taxa that became dominant were relatives of Exiguobacterium, Tissierella and Clostridium. Open reading frames (ORFs) associated with dissimilatory denitrification were identified for Pseudomonas, Thauera and Clostridium. In addition, ORFs were found that were homologous with known selenate reductase subunits (SerA and SerB). These findings suggest that native mine site bacteria can be used for removing selenate and nitrate from mine wastewater. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Spatial distribution of environmental risk associated to a uranium abandoned mine (Central Portugal)

NASA Astrophysics Data System (ADS)

Antunes, I. M.; Ribeiro, A. F.

2012-04-01

The abandoned uranium mine of Canto do Lagar is located at Arcozelo da Serra, central Portugal. The mine was exploited in an open pit and produced about 12430Kg of uranium oxide (U3O8), between 1987 and 1988. The dominant geological unit is the porphyritic coarse-grained two-mica granite, with biotite>muscovite. The uranium deposit consists of two gaps crushing, parallel to the coarse-grained porphyritic granite, with average direction N30°E, silicified, sericitized and reddish jasperized, with a width of approximately 10 meters. These gaps are accompanied by two thin veins of white quartz, 70°-80° WNW, ferruginous and jasperized with chalcedony, red jasper and opal. These veins are about 6 meters away from each other. They contain secondary U-phosphates phases such as autunite and torbernite. Rejected materials (1000000ton) were deposited on two dumps and a lake was formed in the open pit. To assess the environmental risk of the abandoned uranium mine of Canto do Lagar, were collected and analysed 70 samples on stream sediments, soils and mine tailings materials. The relation between samples composition were tested using the Principal Components Analysis (PCA) (multivariate analysis) and spatial distribution using Kriging Indicator. The spatial distribution of stream sediments shows that the probability of expression for principal component 1 (explaining Y, Zr, Nb, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Hf, Th and U contents), decreases along SE-NW direction. This component is explained by the samples located inside mine influence. The probability of expression for principal component 2 (explaining Be, Na, Al, Si, P, K, Ca, Ti, Mn, Fe, Co, Ni, Cu, As, Rb, Sr, Mo, Cs, Ba, Tl and Bi contents), increases to middle stream line. This component is explained by the samples located outside mine influence. The spatial distribution of soils, shows that the probability of expression for principal component 1 (explaining Mg, P, Ca, Ge, Sr, Y, Zr, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu, Hf, W, Th and U contents) decreases along SE direction and increases along NE and SW directions. The probability of expression for principal component 2 (explaining pH, K, Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Sr and Pb contents), decreases from central points (inside mine influence) to peripheral points (outside mine influence) and gradually increases along N and SW directions. The spatial distribution of tailing materials did not allowed a consistent spatial distribution. In general, the stream sediments are classified as unpolluted and not polluted or moderately polluted, according to geoaccumulation Müller index with exception of local samples, located inside mine influence. The soils cannot be used for public, private or residential uses according to the Canadian soil legislation. However, almost samples can be used for commercial or industrial occupation. According to the target values and intervention values for soils remediation, these soils need intervention. Tailing materials samples are much polluted in thorium (Th) and uranium (U) and they cannot be used for public, private or residential uses.

Measures to restore metallurgical mine wasteland using ecological restoration technologies: A case study at Longnan Rare Earth Mine

NASA Astrophysics Data System (ADS)

Rao, Yunzhang; Gu, Ruizhi; Guo, Ruikai; Zhang, Xueyan

2017-01-01

Whereas mining activities produce the raw materials that are crucial to economic growth, such activities leave extensive scarring on the land, contributing to the waste of valuable land resources and upsetting the ecological environment. The aim of this study is therefore to investigate various ecological technologies to restore metallurgical mine wastelands. These technologies include measures such as soil amelioration, vegetation restoration, different vegetation planting patterns, and engineering technologies. The Longnan Rare Earth Mine in the Jiangxi Province of China is used as the case study. The ecological restoration process provides a favourable reference for the restoration of a metallurgical mine wasteland.

Potential implications of mine dusts on human health: A case study of Mukula Mine, Limpopo Province, South Africa

PubMed Central

Momoh, Abuh; E. Mhlongo, Sphiwe; Abiodun, Olukoga; Muzerengi, Confidence; Mudanalwo, Matamela

2013-01-01

Objective: The purpose of this study was to estimate the levels of Suspended Particulate Matter (SPM) in ambient air within Mukula mine and the potential risks to mineworkers and inhabitants of the adjoining Mukula community’s health. Methods : An SPM was used to measure the levels of particulate matter (PM10) in and around the mining site. One-way Analysis of Variance (ANOVA) was used to determine significance level of PM10 in ambient air. Results: Suspended particulate matter in the air ranged from 60.25 to 1820.45 µg/m3. The lowest value of SPM was more than four times the required World Health Organisation’s allowable level in ambient air, which the mine workers and locals would be inhaling. Conclusion: Continuous inhalation of mine dusts by mine workers and locals could result in pulmonary fibrosis, silicosis and lung cancer. The findings from this study support the need to have in place the necessary control measures that will drastically reduce SPM in the air. Such measure includes wet drilling and blasting, sprinkling of water on the mine roads and planting of vegetation around the mines and neighbouring communities. PMID:24550971

Potential implications of mine dusts on human health: A case study of Mukula Mine, Limpopo Province, South Africa.

PubMed

Momoh, Abuh; E Mhlongo, Sphiwe; Abiodun, Olukoga; Muzerengi, Confidence; Mudanalwo, Matamela

2013-11-01

Objective : The purpose of this study was to estimate the levels of Suspended Particulate Matter (SPM) in ambient air within Mukula mine and the potential risks to mineworkers and inhabitants of the adjoining Mukula community's health. Methods : An SPM was used to measure the levels of particulate matter (PM10) in and around the mining site. One-way Analysis of Variance (ANOVA) was used to determine significance level of PM10 in ambient air. Results : Suspended particulate matter in the air ranged from 60.25 to 1820.45 µg/m(3). The lowest value of SPM was more than four times the required World Health Organisation's allowable level in ambient air, which the mine workers and locals would be inhaling. Conclusion : Continuous inhalation of mine dusts by mine workers and locals could result in pulmonary fibrosis, silicosis and lung cancer. The findings from this study support the need to have in place the necessary control measures that will drastically reduce SPM in the air. Such measure includes wet drilling and blasting, sprinkling of water on the mine roads and planting of vegetation around the mines and neighbouring communities.

Numerical Modeling Tools for the Prediction of Solution Migration Applicable to Mining Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martell, M.; Vaughn, P.

1999-01-06

Mining has always had an important influence on cultures and traditions of communities around the globe and throughout history. Today, because mining legislation places heavy emphasis on environmental protection, there is great interest in having a comprehensive understanding of ancient mining and mining sites. Multi-disciplinary approaches (i.e., Pb isotopes as tracers) are being used to explore the distribution of metals in natural environments. Another successful approach is to model solution migration numerically. A proven method to simulate solution migration in natural rock salt has been applied to project through time for 10,000 years the system performance and solution concentrations surroundingmore » a proposed nuclear waste repository. This capability is readily adaptable to simulate solution migration around mining.« less

Influence of tectonic disturbances on the parameters of excavation support with rock anchor

NASA Astrophysics Data System (ADS)

Dyomin, V. F.; Yavorsky, V. V.; Demina, T. V.; Baidikova, N. V.; Protsenko, A. V.

2017-10-01

The mechanism of deformation, movement and rockfalls in structurally disturbed nonuniform rock mass using analytical modeling operation for assessment of the strain-stress state (SSS) of the rock mass around mining has been investigated. The SSS research of the rock masses by means of the ANSYS program of the excavation in the “Saransk” mine of coal mining JSC “ArselorMittal Temirtau” in the Karaganda coal basin has been conducted. The parameters of the exploitation of the anchor support on the mines for fixing the rock bolts in the workings to ensure the safety of mining operations in the areas of geological disturbances have been determined.

Ambient air quality at the wider area of an industrial mining facility at Stratoni, Chalkidiki, Greece.

PubMed

Gaidajis, Georgios; Angelakoglou, Komninos; Gazea, Emmy

2012-01-01

To assess ambient air quality at the wider area of a mining-industrial facility in Chalkidiki, Greece, the particulate matter with an aerodynamic diameter of 10 μm (PM(10)) and its content in characteristic elements, i.e., As, Cd, Cu, Fe, Mn, Pb, Zn were monitored for a period of three years (2008-2010). Gravimetric air samplers were employed for the particulate matter sampling at three sampling stations located in the immediate vicinity of the industrial facility and at a neighbouring residential site. Monitoring data indicated that the 3-year median PM(10) concentrations were 23.3 μg/m(3) at the residential site close to the facility and 28.7 μg/m(3) at the site within the facility indicating a minimal influence from the industrial activities to the air quality of the neighbouring residential area. Both annual average and median PM(10) concentration levels were below the indicative European standards, whereas similar spatial and temporal variation was observed for the PM(10) constituents. The average Pb concentrations measured for the three sampling sites were 0.2, 0.146 and 0.174 μg/m(3) respectively, well below the indicative limit of 0.5 μg/m(3). The quantitative and qualitative comparison of PM(10) concentrations and its elemental constituent for the three sampling stations did not indicate any direct influence of the mining-industrial activities to the air quality of the Stratoni residential area.

Determination of Abutment Pressure in Coal Mines with Extremely Thick Alluvium Stratum: A Typical Kind of Rockburst Mines in China

NASA Astrophysics Data System (ADS)

Zhu, Sitao; Feng, Yu; Jiang, Fuxing

2016-05-01

This paper investigates the abutment pressure distribution in coal mines with extremely thick alluvium stratum (ETAS), which is a typical kind of mines encountering frequent intense rockbursts in China. This occurs due to poor understanding to abutment pressure distribution pattern and the consequent inappropriate mine design. In this study, a theoretical computational model of abutment pressure for ETAS longwall panels is proposed based on the analysis of load transfer mechanisms of key stratum (KS) and ETAS. The model was applied to determine the abutment pressure distribution of LW2302S in Xinjulong Coal Mine; the results of stress and microseismic monitoring verified the rationality of this model. The calculated abutment pressure of LW2302S was also used in the terminal mining line design of LW2301N for rockburst prevention, successfully protecting the main roadway from the adverse influence of the abutment pressure.

Occupational Health and Safety Management and Turnover Intention in the Ghanaian Mining Sector

PubMed Central

Amponsah-Tawiah, Kwesi; Ntow, Michael Akomeah Ofori; Mensah, Justice

2015-01-01

Background The mining industry is considered as one of the most dangerous and hazardous industries and the need for effective and efficient occupational health and safety management is critical to safeguard workers and the industry. Despite the dangers and hazards present in the mining industry, only few studies have focused on how occupational health and safety and turnover intentions in the mines. Method The study suing a cross-sectional survey design collected quantitative data from the 255 mine workers that were conveniently sampled from the Ghanaian mining industry. The data collection tools were standardized questionnaires that measured occupational health and safety management and turnover intentions. These scales were also pretested before their usage in actual data collection. Results The correlation coefficient showed that a negative relationship existed between dimensions of occupational health and safety management and turnover intention; safety leadership (r = −0.33, p < 0.01); supervision (r = −0.26, p < 0.01); safety facilities and equipment (r = −0.32, p < 0.01); safety procedure (r = −0.27, p < 0.01). Among these dimensions, safety leadership and safety facility were significant predictors of turnover intention, (β = −0.28, p < 0.01) and (β = −0.24, p < 0.01) respectively. The study also found that turnover intention of employees is heavily influenced by the commitment of safety leadership in ensuring the effective formulation of policies and supervision of occupational health and safety at the workplace. Conclusion The present study demonstrates that safety leadership is crucial in the administration of occupational health and safety and reducing turnover intention in organizations. PMID:27014486

Analysis of the Metals in Soil-Water Interface in a Manganese Mine

PubMed Central

Ren, Bozhi; Wang, Qian; Chen, Yangbo; Ding, Wenjie; Zheng, Xie

2015-01-01

In order to reveal the influence of the metals of soil-water interface in a manganese mine (Xiangtan, China), on local water environment, there are six kinds of metals (Mn, Ni, Cu, Zn, Cd, and Pb) characterized by measuring their concentration, correlation, source, and special distribution using principal component analysis, single factor, and Nemero comprehensive pollution index. The results showed that the corresponding average concentration was 0.3358, 0.045, 0.0105, 0.0148, 0.0067, and 0.0389 mg/L. The logarithmic concentration of Mn, Zn, and Pb was normal distribution. The correlation coefficients (between Mn and Pb, Mn and Zn, Mn and Ni, Cu and Zn, Cu and Pb, and Zn and Cd) were found to range from 0.5 to 0.6, and those between Cu and Ni and Cu and Cd were below 0.3. It was found that Zn and Mn pollution were caused primarily by ore mining, mineral waste transportation, tailing slag, and smelting plants, while Cu and Ni mainly originate from the mining industry activities and the traffic transportation in the mining area. In addition, the Cd was considered to be produced primarily from the agricultural or anthropogenic activities. The pollution indexes indicated that metal pollution degree was different in soil-water interface streams as listed in increasing order of pollution level as Zn > Ni > Cu > Pb > Mn > Cd. For all of the pollution of the soil-water interface streams, there was moderate metal pollution but along the eastern mine area the pollution seemed to get more serious. There was only a small amount of soil-water interface streams not contaminated by the metals. PMID:26167333

Occupational Health and Safety Management and Turnover Intention in the Ghanaian Mining Sector.

PubMed

Amponsah-Tawiah, Kwesi; Ntow, Michael Akomeah Ofori; Mensah, Justice

2016-03-01

The mining industry is considered as one of the most dangerous and hazardous industries and the need for effective and efficient occupational health and safety management is critical to safeguard workers and the industry. Despite the dangers and hazards present in the mining industry, only few studies have focused on how occupational health and safety and turnover intentions in the mines. The study suing a cross-sectional survey design collected quantitative data from the 255 mine workers that were conveniently sampled from the Ghanaian mining industry. The data collection tools were standardized questionnaires that measured occupational health and safety management and turnover intentions. These scales were also pretested before their usage in actual data collection. The correlation coefficient showed that a negative relationship existed between dimensions of occupational health and safety management and turnover intention; safety leadership (r = -0.33, p < 0.01); supervision (r = -0.26, p < 0.01); safety facilities and equipment (r = -0.32, p < 0.01); safety procedure (r = -0.27, p < 0.01). Among these dimensions, safety leadership and safety facility were significant predictors of turnover intention, (β = -0.28, p < 0.01) and (β = -0.24, p < 0.01) respectively. The study also found that turnover intention of employees is heavily influenced by the commitment of safety leadership in ensuring the effective formulation of policies and supervision of occupational health and safety at the workplace. The present study demonstrates that safety leadership is crucial in the administration of occupational health and safety and reducing turnover intention in organizations.

Analytical and numerical simulation of the steady-state hydrologic effects of mining aggregate in hypothetical sand-and-gravel and fractured crystalline-rock aquifers

USGS Publications Warehouse

Arnold, L.R.; Langer, William H.; Paschke, Suzanne Smith

2003-01-01

Analytical solutions and numerical models were used to predict the extent of steady-state drawdown caused by mining of aggregate below the water table in hypothetical sand-and-gravel and fractured crystalline-rock aquifers representative of hydrogeologic settings in the Front Range area of Colorado. Analytical solutions were used to predict the extent of drawdown under a wide range of hydrologic and mining conditions that assume aquifer homogeneity, isotropy, and infinite extent. Numerical ground-water flow models were used to estimate the extent of drawdown under conditions that consider heterogeneity, anisotropy, and hydrologic boundaries and to simulate complex or unusual conditions not readily simulated using analytical solutions. Analytical simulations indicated that the drawdown radius (or distance) of influence increased as horizontal hydraulic conductivity of the aquifer, mine penetration of the water table, and mine radius increased; radius of influence decreased as aquifer recharge increased. Sensitivity analysis of analytical simulations under intermediate conditions in sand-and-gravel and fractured crystalline-rock aquifers indicated that the drawdown radius of influence was most sensitive to mine penetration of the water table and least sensitive to mine radius. Radius of influence was equally sensitive to changes in horizontal hydraulic conductivity and recharge. Numerical simulations of pits in sand-and- gravel aquifers indicated that the area of influence in a vertically anisotropic sand-and-gravel aquifer of medium size was nearly identical to that in an isotropic aquifer of the same size. Simulated area of influence increased as aquifer size increased and aquifer boundaries were farther away from the pit, and simulated drawdown was greater near the pit when aquifer boundaries were close to the pit. Pits simulated as lined with slurry walls caused mounding to occur upgradient from the pits and drawdown to occur downgradient from the pits. Pits simulated as refilled with water and undergoing evaporative losses had little hydro- logic effect on the aquifer. Numerical sensitivity analyses for simulations of pits in sand-and-gravel aquifers indicated that simulated head was most sensitive to horizontal hydraulic conductivity and the hydraulic conductance of general-head boundaries in the models. Simulated head was less sensitive to riverbed conductance and recharge and relatively insensitive to vertical hydraulic conductivity. Numerical simulations of quarries in fractured crystalline-rock aquifers indicated that the area of influence in a horizontally anisotropic aquifer was elongated in the direction of higher horizontal hydraulic conductivity and shortened in the direction of lower horizontal hydraulic conductivity compared to area of influence in a homogeneous, isotropic aquifer. Area of influence was larger in an aquifer with ground-water flow in deep, low-permeability fractures than in a homogeneous, isotropic aquifer. Area of influence was larger for a quarry intersected by a hydraulically conductive fault zone and smaller for a quarry intersected by a low-conductivity fault zone. Numerical sensitivity analyses for simulations of quarries in fractured crystalline-rock aquifers indicated simulated head was most sensitive to variations in recharge and horizontal hydraulic conductivity, had little sensitivity to vertical hydraulic conductivity and drain cells used to simulate valleys, and was relatively insensitive to drain cells used to simulate the quarry.

Strengths amidst vulnerabilities: the paradox of resistance in a mining-affected community in Guatemala.

PubMed

Caxaj, C Susana; Berman, Helene; Ray, Susan L; Restoule, Jean-Paul; Varcoe, Coleen

2014-11-01

The influence of large-scale mining on the psychosocial wellbeing and mental health of diverse Indigenous communities has attracted increased attention. In previous reports, we have discussed the influence of a gold mining operation on the health of a community in the Western highlands of Guatemala. Here, we discuss the community strengths, and acts of resistance of this community, that is, community processes that promoted mental health amidst this context. Using an anti-colonial narrative methodology that incorporated participatory action research principles, we developed a research design in collaboration with community leaders and participants. Data collection involved focus groups, individual interviews and photo-sharing with 54 men and women between the ages of 18 and 67. Data analysis was guided by iterative and ongoing conversations with participants and McCormack's narrative lenses. Study findings revealed key mechanisms and sources of resistance, including a shared cultural identity, a spiritual knowing and being, 'defending our rights, defending our territory,' and, speaking truth to power. These overlapping strengths were identified by participants as key protective factors in facing challenges and adversity. Yet ultimately, these same strengths were often the most eroded or endangered due the influence of large-scale mining operations in the region. These community strengths and acts of resistance reveal important priorities for promoting mental health and wellbeing for populations impacted by large-scale mining operations. Mental health practitioners must attend to both the strengths and parallel vulnerabilities that may be occasioned by large-scale projects of this nature.

Spatial Temporal Analysis Of Mine-induced Seismicity

NASA Astrophysics Data System (ADS)

Fedotova, I. V.; Yunga, S. L.

The results of analysis of influence mine-induced seismicity on state of stress of a rock mass are represented. The spatial-temporal analysis of influence of mass explosions on rock massif deformation is carried out in the territory of a mine field Yukspor of a wing of the Joined Kirovsk mine JSC "Apatite". Estimation of influence of mass explosions on a massif were determined based firstly on the parameters of natural seismicic regime, and secondly taking into consideration change of seismic energy release. After long series of explosions variations in average number of seismic events was fixed. Is proved, that with increase of a volume of rocks, involved in a deforma- tion the released energy of seismic events, and characteristic intervals of time of their preparation are also varied. At the same time, the mechanism of destruction changes also: from destruction's, of a type shift - separation before destruction's, in a quasi- solid heterogeneous massif (in oxidized zones and zones of actuated faults). Analysis of a database seismicity of a massif from 1993 to 1999 years has confirmed, that the response of a massif on explosions is connected to stress-deformations state a mas- sif and parameters of a mining working. The analysis of spatial-temporal distribution of hypocenters of seismic events has allowed to allocate migration of fissile regions of destruction after mass explosions. The researches are executed at support of the Russian foundation for basic research, - projects 00-05-64758, 01-05-65340.

Evaluating the Effects of Metals on Microorganisms in Flooded Paddy Soils Using the SEM/AVS-Based Approach and Measurements of Exchangeable Metal Concentrations.

PubMed

Kunito, Takashi; Toya, Hitomi; Sumi, Hirotaka; Ishikawa, Yuichi; Toda, Hideshige; Nagaoka, Kazunari; Saeki, Kazutoshi; Aikawa, Yoshio; Matsumoto, Satoshi

2017-04-01

We examined possible adverse effects of heavy metals on microbial activity, biomass, and community composition using the simultaneously extracted metals (SEM)/acid-volatile sulfide (AVS)-based approach and measurements of exchangeable metal concentrations in three paddy soils (wastewater-contaminated soil, mine-contaminated soil, and noncontaminated soil) incubated for 60 days under flooded conditions. Incubation under flooding increased pH and decreased Eh in all samples. AVS increased when Eh decreased to approximately -200 mV for the mine-contaminated and noncontaminated soils, while the wastewater-contaminated soil originally had a high concentration of AVS despite its air-dried condition. Addition of rice straw or alkaline material containing calcium carbonate and gypsum increased AVS levels under flooded conditions. We observed no apparent relationship between soil enzyme activity (β-D-glucosidase and acid phosphatase) and concentrations of SEM, [∑SEM - AVS], and exchangeable metals. Bacterial and fungal community composition, assessed using polymerase chain reaction-denaturing gradient gel electrophoresis (DGGE) analysis targeting rRNA genes, was largely influenced by site of collection and incubation time, but metal contamination did not influence community composition. We observed significant negative correlations between biomass C and [∑SEM - AVS] and between biomass C and ∑SEM, suggesting that [∑SEM - AVS] and ∑SEM might reflect the bioavailability of organic matter to microorganisms in these soils.

Gold mining on Mayan-Mam territory: social unravelling, discord and distress in the Western highlands of Guatemala.

PubMed

Caxaj, C Susana; Berman, Helene; Varcoe, Colleen; Ray, Susan L; Restoulec, Jean-Paul

2014-06-01

This article examines the influence of a large-scale mining operation on the health of the community of San Miguel Ixtahuacán, Guatemala. An anti-colonial narrative approach informed by participatory action research principles was employed. Data collection included focus groups and one-on-one interviews from August to November of 2011. Over this period, we interviewed 15 Mam Mayan men and 41 women (n = 56) between the ages of 18 and 64 including health care workers, educators, spiritual leaders, agricultural workers and previous mine employees from 13 villages within the municipality. Participants' accounts pointed to community health experiences of social unravelling characterized by overlapping narratives of a climate of fear and discord and embodied expressions of distress. These findings reveal the interconnected mechanisms by which local mining operations influenced the health of the community, specifically, by introducing new threats to the safety and mental wellbeing of local residents. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Alchemy and mining: metallogenesis and prospecting in early mining books.

PubMed

Dym, Warren Alexander

2008-11-01

Historians have assumed that alchemy had a close association with mining, but exactly how and why miners were interested in alchemy remains unclear. This paper argues that alchemical theory began to be synthesised with classical and Christian theories of the earth in mining books after 1500, and served an important practical function. The theory of metals that mining officials addressed spoke of mineral vapours (Witterungen) that left visible markings on the earth's surface. The prospector searched for mineral ore in part by studying these indications. Mineral vapours also explained the functioning of the dowsing rod, which prospectors applied to the discovery of ore. Historians of early chemistry and mining have claimed that mining had a modernising influence by stripping alchemy of its theoretical component, but this paper shows something quite to the contrary: mining officials may have been sceptical of the possibility of artificial transmutation, but they were interested in a theory of the earth that could translate into prospecting knowledge.

Accessible reactive surface area and abiotic redox reactivity of iron oxyhydroxides in acidic brines

NASA Astrophysics Data System (ADS)

Strehlau, Jennifer H.; Toner, Brandy M.; Arnold, William A.; Penn, R. Lee

2017-01-01

The reactivity of iron oxyhydroxide nanoparticles in low pH and high ionic strength solutions was quantified to assess abiotic contributions to oxidation-reduction chemistry in acidic brine environments, such as mine groundwater seepage, lakes in Western Australia, and acid mine drainage settings, which are of global interest for their environmental impacts and unique geomicrobiology. Factors expected to influence accessible and reactive surface area, including Fe(II) adsorption and aggregate size, were measured as a function of pH and CaCl2 concentration and related to the kinetics of redox reactions in aqueous suspensions of synthetic goethite (α-FeOOH), akaganeite (β-FeOOH), and ferrihydrite (Fe10O14(OH)2) nanoparticles. Aqueous conditions and iron oxyhydroxides were chosen based on characterization of natural iron-rich mine microbial mats located in Soudan Underground Mine State Park, Minnesota, USA. Quinone species were used as redox sensors because they are well-defined probes and are present in natural organic matter. Fe(II) adsorption to the iron oxyhydroxide mineral surfaces from aqueous solution was measurable only at pH values above 4 and either decreased or was not affected by CaCl2 concentration. Concentrations at or above 0.020 M CaCl2 in acetate buffer (pH 4.5) induced particle aggregation. Assessment of Fe(II) adsorption and particle aggregation in acidic brine suggested that accessible reactive surface area may be limited in acidic brines. This was supported by observations of decreasing benzoquinone reduction rate by adsorbed Fe(II) at high CaCl2 concentration. In contrast, the hydroquinone oxidation rate increased at high CaCl2 concentrations, which may be due to suppressed adsorption of Fe(II) generated by the reaction. Results suggest that iron geochemical cycling in acidic brine environments will be substantially different than for iron oxyhydroxides in low-saline waters with circumneutral pH. These findings have implications for acidic brine lakes and acid mine drainage locations that contain precipitated iron oxyhydroxides.

The nature of fracturing and stress distribution in quartzite around the 1128-M (3700-FT) level of the crescent mine, Coeur d'Alene mining district, Idaho

USGS Publications Warehouse

Miller, C.H.; Skinner, E.H.

1980-01-01

Silver and copper are the principal ores mined from the quartzite at the Crescent mine. Both the main ore-bearing veins and foliation in the quartzite are parallel to the nearly vertical formational contacts. Anisotropy of the quartzite is indicated by both dynamic and static tests. Disking and breakage of core from holes perpendicular to the foliation are about twice what they are in core from holes parallel to foliation. Natural cleavage as well as slabbing and blasting fractures around the tunnels are also controlled by the foliation. Extensive overcore deformation measurements indicate that most of the influence of the tunnels on the "free" stress field is between the rib and a depth of 2.7 m (1 tunnel diameter). The maximum principal stress axis in the free field is nearly horizontal; its magnitude is not much greater than the vertical component and calculations indicate a nearly hydrostatic free stress field. Stress considerably greater than the free field was measured between about 0.3-2.7 m behind the rib and is caused by a transfer of load from above the tunnel opening. Peak stress is in the vertical direction and about 1.7 m behind the rib. An air-injection survey shows that high permeabilities are confined to the highly fractured annulus around a tunnel to a depth of at least 0.6 m. Air-injection measurements could be taken in the interval of about 0.6-1.8 m, but more fractures with high permeabilities may also be present in the annulus from about 0.6-1.2 m. Permeabilities measured deeper than about 1.8 m by the air-injection technique are either very low or nonexistent. The absence of open and noncontinuous fractures beyond about 1.8 m is also indicated by very low porosities and permeabilities of core, very high stresses (which presumably would close fractures), the lack of stains or secondary fillings in disking fractures, a conspicuous lack of ground water in the tunnels, and the fact that fractures encountered in an experimental 0.9-m tunnel did not extend into the 1.8-m tunnel that was mined over it. Air-injection techniques exceed the accuracy of any field deformation measurement now in use, and they are sensitive to permeabilities as small as one microdarcy and to fracture widths as small as 250 nanometers. This technique was applied for future reference in mining design and, perhaps, to be used later to detect microfracturing prior to rockbursts. ?? 1980 Elsevier Scientific Publishing Company.

Geochemical fractions of rare earth elements in soil around a mine tailing in Baotou, China

PubMed Central

Wang, Lingqing; Liang, Tao

2015-01-01

Rare earth mine tailing dumps are environmental hazards because tailing easily leaches and erodes by water and wind. To assess the influence of mine tailing on the geochemical behavior of rare earth elements (REEs) in soil, sixty-seven surface soil samples and three soil profile samples were collected from different locations near China’s largest rare earth mine tailing. The total concentration of REEs in surface soils ranged from 156 to 5.65 × 104 mg·kg−1 with an average value of 4.67 × 103 mg·kg−1, which was significantly higher than the average value in China (181 mg·kg−1). We found obvious fractionation of both light and heavy REEs, which was supported by the North American Shale Composite (NASC) and the Post-Archean Average Australian Shale (PAAS) normalized concentration ratios calculated for selected elements (LaN/YbN, LaN/SmN and GdN/YbN). A slightly positive Ce anomaly and a negative Eu anomaly were also found. For all 14 REEs in soils, enrichment was intensified by the mine tailing sources and influenced by the prevailing wind. PMID:26198417

Geochemical fractions of rare earth elements in soil around a mine tailing in Baotou, China.

PubMed

Wang, Lingqing; Liang, Tao

2015-07-22

Rare earth mine tailing dumps are environmental hazards because tailing easily leaches and erodes by water and wind. To assess the influence of mine tailing on the geochemical behavior of rare earth elements (REEs) in soil, sixty-seven surface soil samples and three soil profile samples were collected from different locations near China's largest rare earth mine tailing. The total concentration of REEs in surface soils ranged from 156 to 5.65 × 10(4) mg·kg(-1) with an average value of 4.67 × 10(3) mg·kg(-1), which was significantly higher than the average value in China (181 mg·kg(-1)). We found obvious fractionation of both light and heavy REEs, which was supported by the North American Shale Composite (NASC) and the Post-Archean Average Australian Shale (PAAS) normalized concentration ratios calculated for selected elements (La(N)/Yb(N), La(N)/Sm(N) and Gd(N)/Yb(N)). A slightly positive Ce anomaly and a negative Eu anomaly were also found. For all 14 REEs in soils, enrichment was intensified by the mine tailing sources and influenced by the prevailing wind.

Tall fescue production and nutrient status on southwest Virginia mine soils. [Festuca arundinadea Schreb

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, J.A.; Daniels, W.L.; Bell, J.C.

Tall fescue (Festuca arundinacea Schreb.) is a hardy grass species commonly used in surface mine reclamation and soil conservation. This study documented changes in fescue production (five growing seasons) and nutrient status (three growing seasons) as influenced by spoil type and various amendments. In Exp. I, fescue growth and nutrient status on five mixes of fertilized sandstone (SS) and siltstone (SiS) spoils were compared. A 2:1 SS/SiS control and treatments of 112 Mg ha/sup -1/ sawdust, native topsoil, and 22, 56, 112, and 224 Mg ha/sup -1/ municipal sewage sludge were compared in Exp. II. Standing biomass was measured inmore » 1982-1984 and 1986 and tissue nutrient levels were measured in 1982-1984. High SiS spoils inhibited initial biomass production in Exp. I, but parent material effect diminished with time. All spoil mixes maintained adequate fescue production for five growing seasons, primarily due to small annual N additions (56 kg ha/sup -1/). In Exp. II, the highest yields were maintained on greater than or equal to 56 Mg ha/sup -1/ sludge treatments. Heavy metal uptake was not a problem, even in very high sludge treatments. Sludge-amended mine soils were superior to both native topsoil and inorganically fertilized spoils in their ability to sustain long-term fescue production without periodic augmentation.« less

Application of ERTS-1 imagery to fracture related mine safety hazards in the coal mining industry. [Indiana

NASA Technical Reports Server (NTRS)

Wier, C. E.; Wobber, F. J. (Principal Investigator); Russell, O. R.; Amato, R. V.; Leshendok, T. V.

1974-01-01

The author has identified the following significant results. New fracture detail of Indiana has been observed and mapped from ERTS-1 imagery. Studies so far indicate a close relationship between the directions of fracture traces mapped from the imagery, fractures measured on bedrock outcrops, and fractures measured in the underground mines. First hand observations and discussions with underground mine operators indicate good correlation of mine hazard maps prepared from ERTS-1/aircraft imagery and actual roof falls. The inventory of refuse piles/slurry ponds of the coal field of Indiana has identified over 225 such sites from past mining operations. These data will serve the State Legislature in making tax decisions on coal mining which take on increased importance because of the energy crisis.

A study on natural radioactivity in Khewra Salt Mines, Pakistan.

PubMed

Baloch, Muzahir Ali; Qureshi, Aziz Ahmed; Waheed, Abdul; Ali, Muhammad; Ali, Nawab; Tufail, Muhammad; Batool, Saima; Akram, Muhammad; Iftikhar, Poonam; Qayyum, Hamza; Manzoor, Shahid; Khan, Hameed Ahmed

2012-01-01

The Khewra Salt Mines, the second largest salt mines in the world, are located 160 km south of Islamabad, the capital of Pakistan. Around 1000 workers are involved in the removal of salt from these mines. More than 40,000 visitors come annually to see the mines. The visitors and workers are directly exposed to the internal and external radiological hazards of radon and gamma rays in these mines. The general public is affected by the intake of the salt containing the naturally occurring radionuclides. Therefore the concentration of radon (²²²Rn) in the Khewra Salt Mines and activity concentrations of the naturally occurring radionuclides in the salt samples from these mines were measured. Both active and passive techniques were employed for the measurement of radon with Radon Alpha Detector (RAD-7) and SSNTD respectively. The concentration of ²²²Rn was 26 ± 4 Bq m⁻³ measured by the active method while 43 ± 8 Bq m⁻³ was measured by the passive method. The activity concentration of the radionuclides was measured using gamma ray spectrometry with HPGe detector. The mean activity of ⁴⁰K in salt samples was found to be 36 ± 20 Bq kg⁻¹ and the concentration of ²²⁶Ra and ²³²Th in the salt samples was below the detection limits. Gamma radiation hazard was assessed in terms of the external gamma dose from salt slabs and the rooms made of salt and the annual effective dose due to gamma radiation. The exposure to radon daughters, annual effective dose and excessive lifetime cancer risk due to radon in the mines were estimated. The mean annual effective dose due to an intake of ⁴⁰K from the salt was calculated as 20.0 ± 11.1 µSv, which is lower than the average annual effective dose rate of 0.29 mSv, received by the ingestion of natural radionuclides. Due to the low concentration values of primordial radionuclides in the salt and radon ²²²Rn) in the mines, a 'low level activity measurement laboratory' is suggested to be established in these mines.

Baseline malaria vector transmission dynamics in communities in Ahafo mining area in Ghana.

PubMed

Dery, Dominic B; Asante, Kwaku P; Zandoh, Charles; Febir, Lawrence G; Brown, Charles; Adjei, George; Antwi-Dadzie, Yaw; Mahama, Emmanuel; Tchum, Kofi; Dosoo, David; Amenga-Etego, Seeba; Adda, Robert; Mensah, Christine; Owusu-Sekyere, Kwabena B; Anderson, Chris; Krieger, Gary; Owusu-Agyei, Seth

2015-04-07

Malaria vector dynamics are relevant prior to commencement of mining activities. A baseline entomology survey was conducted in Asutifi and Tano (referred to as Ahafo) in the Brong-Ahafo geo-political region of Ghana during preparatory stages for mining by Newmont Ghana Gold Limited. Between November 2006 and August 2007, eight Centre for Disease Control light traps were set daily (Monday-Friday) to collect mosquitoes. Traps were hanged in rooms that were selected from a pool of 1,100 randomly selected houses. Types of materials used in construction of houses were recorded and mosquito prevention measures were assessed from occupants. A total of 5,393 mosquitoes were caught that comprised Anopheles gambiae (64.8%), Anopheles funestus (4.2%), as well as Culicines, comprising of Culex (30.4%) and Aedes species (0.6%). The entomological inoculation rate in Asutifi (279 infective bites/person/month) and Tano (487 infective bites/person/month) demonstrate relatively high malaria transmission in Ahafo. The presence or absence of Anopheles vectors in rooms was influenced by the type of roofing material (OR 2.33, 95%CI: 1.29-4.22, p = 0.01) as well as the presence of eaves gaps (OR 1.80, 95%CI: 1.37-2.37, p < 0.01). It was also associated with bed net availability in the room (OR 1.39, 95%CI: 1.08-1.80, p = 0.01). Over 80% of the houses were roofed with corrugated zinc sheets. Over 60% of the houses in Ahafo had no eaves gaps to give access to mosquito entry and exit into rooms and mosquito bed net coverage was over 50%. Other measures used in preventing mosquito bites included; coil (22.1%), insecticide spray (9.4%), repellent cream (4.0%) and smoky fires (1.1%), contributed minimally to individual mosquito preventive measures in impact areas. Similarly, levels of protection; coil (16.9%), insecticide spray (2.8%) and repellent cream (0.3%) for the non-impact areas, depict low individual prevention measures. The survey identified areas where intensified vector control activities would be beneficial. It also demonstrates that transmission in Asutifi and Tano is high even before the commencement of mining operations. This study serves as baseline information to assess impact of mining activities in relation to future vector control interventions.

An Empirical Model for Mine-Blast Loading

DTIC Science & Technology

2014-10-17

fledged experimental program. The numerical approach however suffers from several drawbacks in the mine blast simulations. First, it is a very...Suffield consisted in a pendulum type device to measure global impulse of buried mine [15]. One of the main purposes of the ONAGER pendulum was to study...TP-1 Terminal effects, KTA 1-34 report, 2004. [15] Bues, R., Hlady, S.L. and Bergeron, D.M., Pendulum Measurement of Land Mine Blast Output, Volume

Mineralogical study of stream waters and efflorescent salts in Sierra Minera, SE Spain

NASA Astrophysics Data System (ADS)

Pérez-Sirvent, Carmen; Garcia-Lorenzo, Maria luz; Martinez-Sanchez, Maria Jose; Hernandez, Carmen; Hernandez-Cordoba, Manuel

2015-04-01

Trace elements contained in the residues from mining and metallurgical operations are often dispersed by wind and/or water after their disposal. These areas have severe erosion problems caused by water run-off in which soil and mine spoil texture, landscape topography and regional and microclimate play an important role. Water pollution by dissolved metals in mining areas has mainly been associated with the oxidation of sulphide-bearing minerals exposed to weathering conditions, resulting in low quality effluents of acidic pH and containing a high level of dissolved metals. The studied area, Sierra Minera, is close to the mining region of La Unión (Murcia, SE Spain). This area constituted an important mining centre for more than 2500 years, ceasing activity in 1991. The ore deposits of this zone have iron, lead and zinc as the main metal components. Studied area showed a lot of contaminations sources, formed by mining steriles, waste piles and foundry residues. As a consequence of the long period of mining activity, large volumes of wastes were generated during the mineral concentration and smelting processes. Historically, these wastes were dumped into watercourses, filling riverbeds and contaminating their surroundings. 40 sediment samples were collected from the area affected by mining exploitations, and at increasing distances from the contamination sources in 4 zones In addition, 36 surficial water samples were collected after a rain episode The Zn and Fe content was determined by flame atomic absorption spectrometry (FAAS). The Pb and Cd content was determined by electrothermal atomization atomic absorption spectrometry (ETAAS). The As content was measured by atomic fluorescence spectrometry using an automated continuous flow hydride generation spectrometer and Al content was determined by ICP-MS. Mineralogical composition of the samples was made by X Ray Diffraction (XRD) analysis using Cu-Kα radiation with a PW3040 Philips Diffractometer. Zone A: Water sample collected in A5 is strongly influenced by a tailing dump, and showed high trace element contents. In addition, is influenced by the sea water and then showed high bromide, chloride, sodium and magnesium content, together with a basic pH.The DRX results of evaporate water showed that halite, hexahydrite and gypsum are present: halite corroborates the sea influence and gypsum and hexahydrite the importance of soluble sulphates. A9 water showed acid pH and high trace elements content; is influenced by the tailing dump and also by waters from El Beal gully watercourse, transporting materials from Sierra Minera Waters affected by secondary contamination are influenced by mining wastes, the sea water and also are affected by agricultural activities (nitrate content). These waters have been mixed with carbonate materials, present in the zone increasing the pH. Some elements have precipitated, such as Cu and Pb, while Cd, Zn and As are soluble. The DRX analysis in the evaporate if A14 showed that halite and gypsum are present: halite confirms the seawater influence and gypsum the relationship between calcium and sulphates A2 and A6 waters are affected by tertiary contamination and showed basic pH, soluble carbonates and lower trace element content. Only Zn, Cd and Al are present. Zone B: All waters are strongly affected by mining activities and showed: acid pH, high trace element content and high content of soluble sulphates. The evaporate of B8 and B12 showed the presence of soluble sulphates: gypsum, halite, bianchite, paracoquimbite, halotrichite and siderotil in B8; gypsum, bianchite, paracoquimbite and coquimbite in B12; gypsum, hexahydrite, carnalite, bianchite, copiapite and sideroti in B10 and polihalite, gypsum, bianchite, coquimbite and paracoquimbite in B14. All the sampling points collected in Zone C are affected by primary contamination, because there are a lot of tailing dumps and sampling points are located close to them. C1 showed high trace element content because is a reception point of a lot of tailing dumps. Water samples from C3 to C8 also had acid pH and high trace element content, particularly As (remains soluble) and Zn and Cd (high mobility). In addition, they showed high soluble sulphates. C2 water showed neutral pH, soluble carbonate and low trace element content because is influenced by a stabilised tailing dump. However, the As remains soluble. Zone D: All waters collected in this zone showed acid pH and high trace element content, mainly Zn, Cd and As. Some differences were found from the high and the low part: samples located in the lower part (D2-D7) showed higher As content while Zn is higher in the high part (D8-D13) The DRX analysis in evaporates suggest that in D4 copiapite, coquimbite, gypsum, bianchite and ferrohexahydrite are formed and in D11 gypsum, bianchite, halotrichite and siderotil. D1 is affected by secondary contamination, which showed higher pH (still acid) and lower content in soluble salts and trace elements.

Some aspects of forecasting the post-mining substratum deformation for evaluation of its influence on constructions

NASA Astrophysics Data System (ADS)

Strzałkowski, Piotr; Ścigała, Roman; Szafulera, Katarzyna

2018-04-01

Some problems have been discussed, connected with performing predictions of post-mining terrain deformations. Especially problems occur with the summation of horizontal strain over long time intervals as well as predictions of linear discontinuous deformations. Of great importance in recent years is the problem of taking into account transient values of deformations associated with the development of extraction field. The exemplary analysis has been presented of planned extraction influences on two characteristic locations of building structure. The proposal has been shown of calculations with using transient deformation model allowing to describe the influence of extraction advance influence on the value of coefficient of extraction rate c (time factor), according to own original empirical formula.

Indirect Measures of Learning Transfer between Real and Virtual Environments

ERIC Educational Resources Information Center

Garrett, Michael; McMahon, Mark

2013-01-01

This paper reports on research undertaken to determine the effectiveness of a 3D simulation environment used to train mining personnel in emergency evacuation procedures, designated the Fires in Underground Mines Evacuation Simulator (FUMES). Owing to the operational constraints of the mining facility, methods for measuring learning transfer were…

Sulfate-Reducing Bioreactors For The Treatment Of Acid Mine Drainage

EPA Science Inventory

Mine influenced water (MIW) affects a large portion of mountainous surface water bodies in the western United States as well as elsewhere. In this study, the purpose of this applied research is to compare different substrates used in biochemical reactors (BCRs) field test cells ...

Field-scale study of the influence of differing remediation strategies on trace metal geochemistry in metal mine tailings from the Irish Midlands.

PubMed

Perkins, William T; Bird, Graham; Jacobs, Suzanne R; Devoy, Cora

2016-03-01

Mine tailings represent a globally significant source of potentially harmful elements (PHEs) to the environment. The management of large volumes of mine tailings represents a major challenge to the mining industry and environmental managers. This field-scale study evaluates the impact of two highly contrasting remediation approaches to the management and stabilisation of mine tailings. The geochemistry of the tailings, overlying amendment layers and vegetation are examined in the light of the different management approaches. Pseudo-total As, Cd and Pb concentrations and solid-state partitioning (speciation), determined via sequential extraction, were established for two Tailings Management Facilities (TMFs) in Ireland subjected to the following: (1) a 'walk-away' approach (Silvermines) and (2) application of an amendment layer (Galmoy). PHE concentrations in roots and herbage of grasses growing on the TMFs were also determined. Results identify very different PHE concentration profiles with depth through the TMFs and the impact of remediation approach on concentrations and their potential bioavailability in the rooting zone of grass species. Data also highlight the importance of choice of grass species in remediation approaches and the benefits of relatively shallow-rooting Agrostis capillaris and Festuca rubra varieties. In addition, data from the Galmoy TMF indicate the importance of regional soil geochemistry for interpreting the influence of the PHE geochemistry of capping and amendment layers applied to mine tailings.

Nanofiltration of Mine Water: Impact of Feed pH and Membrane Charge on Resource Recovery and Water Discharge

PubMed Central

Mullett, Mark; Fornarelli, Roberta; Ralph, David

2014-01-01

Two nanofiltration membranes, a Dow NF 270 polyamide thin film and a TriSep TS 80 polyamide thin film, were investigated for their retention of ionic species when filtering mine influenced water streams at a range of acidic pH values. The functional iso-electric point of the membranes, characterized by changes in retention over a small pH range, were examined by filtering solutions of sodium sulphate. Both membranes showed changes in retention at pH 3, suggesting a zero net charge on the membranes at this pH. Copper mine drainage and synthetic solutions of mine influenced water were filtered using the same membranes. These solutions were characterized by pH values within 2 and 5, thus crossing the iso-electric point of both membranes. Retention of cations was maximized when the feed solution pH was less than the iso-electric point of the membrane. In these conditions, the membrane has a net positive charge, reducing the transmission rate of cations. From the recoveries of a range of cations, the suitability of nanofiltration was discussed relative to the compliance with mine water discharge criteria and the recovery of valuable commodity metals. The nanofiltration process was demonstrated to offer advantages in metal recovery from mine waste streams, concomitantly enabling discharge criteria for the filtrate disposal to be met. PMID:24957170

The effects of heavy metal mine drainage on population size structure, reproduction, and condition of western mosquitofish, Gambusia affinis.

PubMed

Franssen, Courtney M

2009-07-01

Anthropogenic degradation of aquatic environments worldwide results in disturbed habitats, altered communities, and stressed populations. Surface waters located in an abandoned lead-zinc mining district in northeastern Oklahoma are no exception. This study examines the reproductive and somatic responses of a pollution-tolerant fish, the western mosquitofish, Gambusia affinis (Teleostei: Poeciliidae), living in mine outflow waters contaminated by heavy metals. Populations were sampled from four streams, which were classified into three habitat types. Populations from Tar Creek and an Unnamed Tributary of Tar Creek receive direct input of mine drainage, while populations living in reference creeks are not known to have mining influence. The influence of mine drainage directly or indirectly (via altered competitor and predator regimes or changes in food availability) affects G. affinis at both the population and the individual level. Metal-contaminated sites had reduced proportions of males and reproductively active females and altered male population size structures. Individual-level effects were apparent, as all G. affinis from Tar Creek invested less in liver weights, and mature males and reproductively active females from Tar Creek invested less in gonad weights. Furthermore, males from impacted sites were significantly lighter than those from reference creeks. Gravid females from Tar Creek had smaller clutch sizes, but average embryo weight did not differ among streams.

Mine dewatering and impact assessment in an arid area: Case of Gulf region.

PubMed

Yihdego, Yohannes; Drury, Len

2016-11-01

Analytical and empirical solution coupled with water balance method were used to predict the ground water inflow to a mine pit excavated below the water table, final pit lake level/recovery and radius of influence, through long-term and time variant simulations. The solution considers the effect of decreased saturated thickness near the pit walls, distributed recharge to the water table and upward flow through the pit bottom. The approach is flexible to accommodate the anisotropy/heterogeneity of the real world. Final pit void water level was assessed through scenarios to know whether it will be consumed by evaporation and a shallow lake will form or not. The optimised radius of influence was estimated which is considered as crucial information in relation to the engineering aspects of mine planning and sustainable development of the mine area. Time-transient inflow over a period of time was estimated using solutions, including analytical element method (AEM). Their primary value is in providing estimates of pit inflow rates to be used in the mine dewatering. Inflow estimation and recovery helps whether there is water to supplement the demand and if there is any recovery issue to be dealt with in relation to surface and groundwater quality/eco-system, environmental evaluations and mitigation. Therefore, this method is good at informing decision makers in assessing the effects of mining operations and developing an appropriate water management strategy.

Geochemistry of acid mine drainage from a coal mining area and processes controlling metal attenuation in stream waters, southern Brazil.

PubMed

Campaner, Veridiana P; Luiz-Silva, Wanilson; Machado, Wilson

2014-05-14

Acid drainage influence on the water and sediment quality was investigated in a coal mining area (southern Brazil). Mine drainage showed pH between 3.2 and 4.6 and elevated concentrations of sulfate, As and metals, of which, Fe, Mn and Zn exceeded the limits for the emission of effluents stated in the Brazilian legislation. Arsenic also exceeded the limit, but only slightly. Groundwater monitoring wells from active mines and tailings piles showed pH interval and chemical concentrations similar to those of mine drainage. However, the river and ground water samples of municipal public water supplies revealed a pH range from 7.2 to 7.5 and low chemical concentrations, although Cd concentration slightly exceeded the limit adopted by Brazilian legislation for groundwater. In general, surface waters showed large pH range (6 to 10.8), and changes caused by acid drainage in the chemical composition of these waters were not very significant. Locally, acid drainage seemed to have dissolved carbonate rocks present in the local stratigraphic sequence, attenuating the dispersion of metals and As. Stream sediments presented anomalies of these elements, which were strongly dependent on the proximity of tailings piles and abandoned mines. We found that precipitation processes in sediments and the dilution of dissolved phases were responsible for the attenuation of the concentrations of the metals and As in the acid drainage and river water mixing zone. In general, a larger influence of mining activities on the chemical composition of the surface waters and sediments was observed when enrichment factors in relation to regional background levels were used.

78 FR 12756 - Proposed Data Collections Submitted for Public Comment and Recommendations

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-25

... strategies, including self- report pre-and post-test instruments for assessing trainee reaction and measuring... Knowledge Test. Mine Escape/Continuous Mining Pre/Post- 30 1 6/60 3 participants. Training Knowledge Test. Mine Rescue/Longwall Mining Pre/Post- 30 1 6/60 3 participants. Training Knowledge Test. Mine Rescue...

Individual and cumulative effects of agriculture, forestry and metal mining activities on the metal and phosphorus content of fluvial fine-grained sediment; Quesnel River Basin, British Columbia, Canada.

PubMed

Smith, Tyler B; Owens, Philip N

2014-10-15

The impact of agriculture, forestry and metal mining on the quality of fine-grained sediment (<63 μm) was investigated in the Quesnel River Basin (QRB) (~11,500 km(2)) in British Columbia, Canada. Samples of fine-grained sediment were collected monthly during the snow-free season in 2008 using time-integrated samplers at replicate sites representative of agriculture, forestry and mining activities in the basin (i.e. "impacted" sites). Samples were also collected from replicate reference sites and also from the main stem of the Quesnel River at the downstream confluence with the Fraser River. Generally, metal(loid) and phosphorus (P) concentrations for "impacted" sites were greater than for reference sites. Furthermore, concentrations of copper (forestry and mining sites), manganese (agriculture and forestry sites) and selenium (agriculture, forestry and mining sites) exceeded upper sediment quality guideline (SQG) thresholds. These results suggest that agriculture, forestry and metal mining activities are having an influence on the concentrations of sediment-associated metal(loid)s and P in the Quesnel basin. Metal(loid) and P concentrations of sediment collected from the downstream site were not significantly greater than values for the reference sites, and were typically lower than the values for the impacted sites. This suggests that the cumulative effects of agriculture, forestry and mining activities in the QRB are presently not having a measureable effect at the river basin-scale. The lack of a cumulative effect at the basin-scale is thought to reflect: (i) the relatively recent occurrence of land use disturbances in this basin; (ii) the dominance of sediment contributions from natural forest and agriculture; and (iii) the potential for storage of contaminants on floodplains and other storage elements between the locations of disturbance activities and the downstream sampling site, which may be attenuating the disturbance signal. Copyright © 2014 Elsevier B.V. All rights reserved.

Impact of an iron mine and a nickel smelter at the Norwegian/Russian border close to the Barents Sea on surface soil magnetic susceptibility and content of potentially toxic elements.

PubMed

Magiera, Tadeusz; Zawadzki, Jarosław; Szuszkiewicz, Marcin; Fabijańczyk, Piotr; Steinnes, Eiliv; Fabian, Karl; Miszczak, Ewa

2018-03-01

An important problem in soil magnetometry is unraveling the soil contamination signal in areas with multiple emitters. Here, geophysical and geochemical measurements were performed at four sites on a north - south transect along the Pasvik River in the Barents Region (northern Norway). These sites are influenced by depositions from the Bjørnevatn iron mine and a Ni-Cu smelter in Nikel, Russia. To relate the degree and type of pollution from these sources to the corresponding magnetic signal, the topsoil concentrations of 12 Potentially Toxic Elements (PTEs) (As, Cd, Co, Cr, Cu, Fe, Mo, Ni, Pb, Se, Ti, Zn), were determined, magnetic hysteresis parameters and thermomagnetic properties were measured. In situ magnetic low-field susceptibility decreases from north to south with increasing distance from the iron mine. Relatively large magnetic multidomain grains of magnetite and/or titanomagnetite are responsible for the strong magnetic signal from the topsoil close to Bjørnevatn. These particles are related to increased enrichment factors of As, Mo and Cu, yielding high positive correlation coefficients with susceptibility values. At a site furthest away from the iron mine and located 7 km from the Ni-Cu smelter magnetic susceptibility values are much lower but significant positive correlations on the level of p < .1 with 8 PTEs (Ni, Cu, Co, Se, As, Zn, Cd, Cr) have been observed. The magnetic signal in this area is due to fine-grained primary sulphides and secondary fine-grained magnetite and/or maghemite. Copyright © 2017 Elsevier Ltd. All rights reserved.

Groundwater hydrogeochemical characteristics in rehabilitated coalmine spoils

NASA Astrophysics Data System (ADS)

Gomo, M.; Masemola, E.

2016-04-01

The investigation aims to identify and describe hydrogeochemical processes controlling the evolution of groundwater chemistry in rehabilitated coalmine spoils and their overall influence on groundwater quality at a study area located in the Karoo basin of South Africa. A good understanding of the processes that controls the evolution of the mine water quality is vital for the planning, application and management of post-mining remedial actions. The study utilises scatter plots, statistical analysis, PHREEQC hydrogeochemical modelling, stoichiometric reaction ratios analysis, and the expanded Durov diagram as complimentary tools to interpret the groundwater chemistry data collected from monitoring boreholes from 1995 to 2014. Measured pH ranging between 6-8 and arithmetic mean of 7.32 shows that the groundwater system is characterised by circumneutral hydrogeochemical conditions period. Comparison of measured groundwater ion concentrations to theoretical reaction stoichiometry identifies Dolomite-Acid Mine Drainage (AMD) neutralisation as the main hydrogeochemical process controlling the evolution of the groundwater chemistry. Hydrogeochemical modelling shows that, the groundwater has temporal variations of calcite and dolomite saturation indices characterised by alternating cycles of over-saturation and under-saturation that is driven by the release of sulphate, calcium and magnesium ions from the carbonate-AMD neutralization process. Arithmetic mean concentrations of sulphate, calcium and magnesium are in the order of 762 mg/L, 141 mg/L and 108 mg/L. Calcium and magnesium ions contribute to very hard groundwater quality conditions. Classification based on total dissolved solids (TDS), shows the circumneutral water is of poor to unacceptable quality for drinking purposes. Despite its ability to prevent AMD formation and leaching of metals, the dolomite-AMD neutralisation process can still lead to problems of elevated TDS and hardness which mines should be aware of when developing water quality management plans.

The self-absorption correction factors for 210Pb concentration in mining waste and influence on environmental radiation risk assessment.

PubMed

Bonczyk, Michal; Michalik, Boguslaw; Chmielewska, Izabela

2017-03-01

The radioactive lead isotope 210 Pb occurs in waste originating from metal smelting and refining industry, gas and oil extraction and sometimes from underground coal mines, which are deposited in natural environment very often. Radiation risk assessment requires accurate knowledge about the concentration of 210 Pb in such materials. Laboratory measurements seem to be the only reliable method applicable in environmental 210 Pb monitoring. One of the methods is gamma-ray spectrometry, which is a very fast and cost-effective method to determine 210 Pb concentration. On the other hand, the self-attenuation of gamma ray from 210 Pb (46.5 keV) in a sample is significant as it does not depend only on sample density but also on sample chemical composition (sample matrix). This phenomenon is responsible for the under-estimation of the 210 Pb activity concentration level often when gamma spectrometry is applied with no regard to relevant corrections. Finally, the corresponding radiation risk can be also improperly evaluated. Sixty samples of coal mining solid tailings (sediments created from underground mining water) were analysed. Slightly modified and adapted to the existing laboratory condition, a transmission method has been applied for the accurate measurement of 210 Pb concentration . The observed concentrations of 210 Pb range between 42.2 ÷ 11,700 Bq·kg -1 of dry mass. Experimentally obtained correction factors related to a sample density and elemental composition range between 1.11 and 6.97. Neglecting this factor can cause a significant error or underestimations in radiological risk assessment. The obtained results have been used for environmental radiation risk assessment performed by use of the ERICA tool assuming exposure conditions typical for the final destination of such kind of waste.

Satellite data for surface-mine inventory. [in Maryland

NASA Technical Reports Server (NTRS)

Anderson, A. T.; Schultz, D.; Buchman, N.; Nock, M.

1976-01-01

To determine the feasibility of satellite data for surface-mine inventory, particularly as it applies to coal, a case study was conducted in Maryland. A band-ratio method was developed to measure disturbed surface areas, and it proved to be extendible both temporally and geographically. This method was used to measure area changes in the region over three time periods from September 1972 through July 1974 and to map the entire two-county area for 1973. For mines ranging between 31 and 244 acres (12 to 98 hectares) the measurement accuracy of total affected acreage was determined to be 92%. Mines of 120 acres (50 hectares) and larger were measured with greater accuracy, some within one percent of the actual area. The ability to identify, classify, and measure strip-mine surfaces in a two-county area (1,541 square kilometers - 595 square miles) of western Maryland was demonstrated through the use of computer processing. On the basis of these results the use of LANDSAT satellite data and multilevel sampling of aircraft and field verification inspections, multispectral analysis of digital data is shown to be an effective, rapid, and accurate means of monitoring the surface mining cycle.

Study on association between spatial distribution of metal mines and disease mortality: a case study in Suxian District, South China.

PubMed

Song, Daping; Jiang, Dong; Wang, Yong; Chen, Wei; Huang, Yaohuan; Zhuang, Dafang

2013-10-16

Metal mines release toxic substances into the environment and can therefore negatively impact the health of residents in nearby regions. This paper sought to investigate whether there was excess disease mortality in populations in the vicinity of the mining area in Suxian District, South China. The spatial distribution of metal mining and related activities from 1985 to 2012, which was derived from remote sensing imagery, was overlapped with disease mortality data. Three hotspot areas with high disease mortality were identified around the Shizhuyuan mine sites, i.e., the Dengjiatang metal smelting sites, and the Xianxichong mine sites. Disease mortality decreased with the distance to the mining and smelting areas. Population exposure to pollution was estimated on the basis of distance from town of residence to pollution source. The risk of dying according to disease mortality rates was analyzed within 7-25 km buffers. The results suggested that there was a close relationship between the risk of disease mortality and proximity to the Suxian District mining industries. These associations were dependent on the type and scale of mining activities, the area influenced by mining and so on.

Study on Association between Spatial Distribution of Metal Mines and Disease Mortality: A Case Study in Suxian District, South China

PubMed Central

Song, Daping; Jiang, Dong; Wang, Yong; Chen, Wei; Huang, Yaohuan; Zhuang, Dafang

2013-01-01

Metal mines release toxic substances into the environment and can therefore negatively impact the health of residents in nearby regions. This paper sought to investigate whether there was excess disease mortality in populations in the vicinity of the mining area in Suxian District, South China. The spatial distribution of metal mining and related activities from 1985 to 2012, which was derived from remote sensing imagery, was overlapped with disease mortality data. Three hotspot areas with high disease mortality were identified around the Shizhuyuan mine sites, i.e., the Dengjiatang metal smelting sites, and the Xianxichong mine sites. Disease mortality decreased with the distance to the mining and smelting areas. Population exposure to pollution was estimated on the basis of distance from town of residence to pollution source. The risk of dying according to disease mortality rates was analyzed within 7–25 km buffers. The results suggested that there was a close relationship between the risk of disease mortality and proximity to the Suxian District mining industries. These associations were dependent on the type and scale of mining activities, the area influenced by mining and so on. PMID:24135822

Optimizing longwall mine layouts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Minkel, M.J.

1996-12-31

Before spending the time to design an underground mine in detail, the mining engineer should be assured of the economic viability of the location of the layout. This has historically been a trial-and-error, iterative process. Traditional underground mine planning usually bases the layout on the geological characteristics of a deposit such as minimum seam height, quality, and the absence of faults. Whether one attempts to make a decision manually. or use traditional mine planning software, the process works something like this: First you build geological model. Then you impose a {open_quotes}best guess{close_quotes} as to which geological layers will become partmore » of the mined product, or will influence mining. Next you place your design where you believe is the best location to make a mine. Then you select equipment which you believe will cost-effectively mine the area. Finally, you schedule your equipment selection through the design over the mine life, run financial analyses and see if the rate of return is acceptable. If the NPV is acceptable, the design is accepted. If the NPV is not acceptable, the engineer has to restart the cycle of redesigning the layout, rescheduling the equipment, and restudying the economics again.« less

A geographical information system-based analysis of cancer mortality and population exposure to coal mining activities in West Virginia, United States of America.

PubMed

Hendryx, Michael; Fedorko, Evan; Anesetti-Rothermel, Andrew

2010-05-01

Cancer incidence and mortality rates are high in West Virginia compared to the rest of the United States of America. Previous research has suggested that exposure to activities of the coal mining industry may contribute to elevated cancer mortality, although exposure measures have been limited. This study tests alternative specifications of exposure to mining activity to determine whether a measure based on location of mines, processing plants, coal slurry impoundments and underground slurry injection sites relative to population levels is superior to a previously-reported measure of exposure based on tons mined at the county level, in the prediction of age-adjusted cancer mortality rates. To this end, we utilize two geographical information system (GIS) techniques--exploratory spatial data analysis and inverse distance mapping--to construct new statistical analyses. Total, respiratory and "other" age-adjusted cancer mortality rates in West Virginia were found to be more highly associated with the GIS-exposure measure than the tonnage measure, before and after statistical control for smoking rates. The superior performance of the GIS measure, based on where people in the state live relative to mining activity, suggests that activities of the industry contribute to cancer mortality. Further confirmation of observed phenomena is necessary with person-level studies, but the results add to the body of evidence that coal mining poses environmental risks to population health in West Virginia.

Selection of basic data for numerical modeling of rock mass stress state at Mirny Mining and Processing Works, Alrosa Group of Companies

NASA Astrophysics Data System (ADS)

Bokiy, IB; Zoteev, OV; Pul, VV; Pul, EK

2018-03-01

The influence of structural features on the strength and elasticity modulus is studied in rock mass in the area of Mirny Mining and Processing Works. The authors make recommendations on the values of physical properties of rocks.

Evaluation of Mineral Assets: Interconnection of Financial and Managerial Aspects

ERIC Educational Resources Information Center

Sergeev, Igor B.; Lebedeva, Olesia Y.

2016-01-01

Mining business makes no sense without mineral assets comprising mineral rights, exploration and evaluation expenditures, development costs, ore reserves and resources. The paper is aimed at investigation of how mineral reserves and resources are evaluated and represented in financial statements of mining companies, and what kind of influence do…

Development of a multilevel health and safety climate survey tool within a mining setting.

PubMed

Parker, Anthony W; Tones, Megan J; Ritchie, Gabrielle E

2017-09-01

This study aimed to design, implement and evaluate the reliability and validity of a multifactorial and multilevel health and safety climate survey (HSCS) tool with utility in the Australian mining setting. An 84-item questionnaire was developed and pilot tested on a sample of 302 Australian miners across two open cut sites. A 67-item, 10 factor solution was obtained via exploratory factor analysis (EFA) representing prioritization and attitudes to health and safety across multiple domains and organizational levels. Each factor demonstrated a high level of internal reliability, and a series of ANOVAs determined a high level of consistency in responses across the workforce, and generally irrespective of age, experience or job category. Participants tended to hold favorable views of occupational health and safety (OH&S) climate at the management, supervisor, workgroup and individual level. The survey tool demonstrated reliability and validity for use within an open cut Australian mining setting and supports a multilevel, industry specific approach to OH&S climate. Findings suggested a need for mining companies to maintain high OH&S standards to minimize risks to employee health and safety. Future research is required to determine the ability of this measure to predict OH&S outcomes and its utility within other mine settings. As this tool integrates health and safety, it may have benefits for assessment, monitoring and evaluation in the industry, and improving the understanding of how health and safety climate interact at multiple levels to influence OH&S outcomes. Copyright © 2017 National Safety Council and Elsevier Ltd. All rights reserved.

Preliminary study of detection of buried landmines using a programmable hyperspectral imager

NASA Astrophysics Data System (ADS)

McFee, John E.; Ripley, Herb T.; Buxton, Roger; Thriscutt, Andrew M.

1996-05-01

Experiments were conducted to determine if buried mines could be detected by measuring the change in reflectance spectra of vegetation above mine burial sites. Mines were laid using hand methods and simulated mechanical methods and spectral images were obtained over a three month period using a casi hyperspectral imager scanned from a personnel lift. Mines were not detectable by measurement of the shift of the red edge of vegetative spectra. By calculating the linear correlation coefficient image, some mines in light vegetative cover (grass, grass/blueberries) were apparently detected, but mines buried in heavy vegetation cover (deep ferns) were not detectable. Due to problems with ground truthing, accurate probabilities of detection and false alarm rates were not obtained.

Inclusions and Their Influence on Material Behavior: Proceedings of a Symposium Held in Conjunction with the 1988 World Materials Congress, Chicago, Illinois, USA, 24-30 September 1988

DTIC Science & Technology

1988-01-01

Columbus Division V TABLE OF CONTENTS Inclusions: Advantages, Disadvantages, and the Technological Trends ................. 1 R. Rungta, A. J...these phases [1]. A similar summary of sulphide Advances in noninvasive technologies for de- inclusions important to steel making is shown in tecting and...MEASUREMENT OF SPATIAL DISTRIBUTION OF INCLUSIONS M. T. Shehata, J. D. Boyd Metals Technology Laboratories CANMET - Energy, Mines & Resources Canada Ottawa

Ocular findings in coal miners diagnosed with pneumoconiosis.

PubMed

Ayar, Orhan; Orcun Akdemir, Mehmet; Erboy, Fatma; Yazgan, Serpil; Hayri Ugurbas, Suat

2017-06-01

Our study aimed at evaluating ocular findings and structural changes in coal mine workers who were chronically exposed to coal mine dust and diagnosed with pneumoconiosis. Ocular findings of 161 eyes of 81 patients diagnosed with pneumoconiosis who had previously worked or are currently working in coal mines were analyzed. Forty-six coal mine workers and sex matched healthy people (n = 20) participated in the study. Workers who had early changes of pneumoconiosis were included in Group 1 (n = 17), workers diagnosed with pneumoconiosis were included in Group 2 (n = 29), and healthy subjects were included in Group 3 (n = 20). Outcome measures were the difference in peripapillary retinal nerve fiber layer (RNFL) thickness, choroidal thickness (CT), central macular thickness (CMT) and tear function tests between the groups. RNFL thickness values in Group 1 and 2 were lower than in Group 3, the control group, in all quadrants except the temporal quadrant. However, there was no statistically significant difference in peripapillary RNFL thickness values in any quadrants among the three groups (p > 0.05). Central subfoveal choroidal thickness and CMT measurements were thinner in Group 1 and 2 than in the control group. However, this difference among groups was not statistically significant (p > 0.05). Mean schirmer's test result was 8.8 ± 1.6 mm in group 1, 7.1 ± 1.8 mm in Group 2 and 11.5 ± 3.6 mm in the control group. Mean tear break up time (BUT) test result was 7.1 ± 1.3 seconds (sec) in Group 1, 6.5 ± 1.8 sec in Group 2 and 10.4 ± 2.9 s in the control group. The Schirmer's test and BUT test results were both statistically significantly lower in coal mine workers (Group 1 and 2) compared to the control group. Group 1 and Group 2 did not show statistically significant difference in terms of Schirmer's test and BUT test results. The association between pneumoconiosis and coal mine dust contiguity is thought to be due to the effect of coal dust by producing chronic inflammation. In addition, there are several trace elements in coal dust which are toxic to vital tissues. In this study, ocular findings suggest that systemic levels of trace elements and chronic inflammation may not reach to a level that influences ocular structures. Nonetheless, tear functions seem to be affected in coal mine workers. This study suggests that the systemic effect of coal mine dust in ocular structures is not evident. However, direct contact with coal mine and fume leads to a decrease in tear function tests.

Photosynthesis and yield reductions from wheat stem sawfly (Hymenoptera: Cephidae): interactions with wheat solidness, water stress, and phosphorus deficiency.

PubMed

Delaney, Kevin J; Weaver, David K; Peterson, Robert K D

2010-04-01

The impact of herbivory on plants is variable and influenced by several factors. The current study examined causes of variation in the impact of larval stem mining by the wheat stem sawfly, Cephus cinctus Norton (Hymenoptera: Cephidae), on spring wheat, Triticum aestivum L. We performed greenhouse experiments over 2 yr to (1) study whether biotic (hollow versus solid stemmed host wheat) and abiotic (water, phosphorus stress) factors interact with C. cinctus stem mining to influence degree of mined stem physiological (photosynthesis) and yield (grain weight) reductions; and (2) determine whether whole plant yield compensatory responses occur to offset stem-mining reductions. Flag leaf photosynthetic reduction was not detected 16-20 d after infestation, but were detected at 40-42 d and doubled from water or phosphorus stresses. Main stem grain weight decreased from 10 to 25% from stem mining, largely due to reductions in grain size, with greater reductions under low phosphorus and/or water levels. Phosphorus-deficient plants without water stress were most susceptible to C. cinctus, more than doubling the grain weight reduction due to larval feeding relative to other water and phosphorus treatments. Two solid stemmed varieties with stem mining had less grain weight loss than a hollow stemmed variety, so greater internal mechanical resistance may reduce larval stem mining and plant yield reductions. Our results emphasize the importance of sufficient water and macronutrients for plants grown in regions impacted by C. cinctus. Also, solid stemmed varieties not only reduce wheat lodging from C. cinctus, they may reduce harvested grain losses from infested stems.

Kinetics of bed fracturing around mine workings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Veksler, Yu.A.

1988-03-01

A failure of the bed near the walls of the workings of a mine away from the face occurs gradually over time and in this paper the authors take a kinetic approach to evaluating its development. The influence of certain mine engineering factors on the pattern of bed fracturing is discussed. The effect of the depth of mining is shown. Cracking occurs in the portion of the seam at the face near the ground at some distance from it on the interface between soft and hard coal. The density of the fractured rocks and their response affect the bed fracturingmore » near the stope face.« less

The study on privacy preserving data mining for information security

NASA Astrophysics Data System (ADS)

Li, Xiaohui

2012-04-01

Privacy preserving data mining have a rapid development in a short year. But it still faces many challenges in the future. Firstly, the level of privacy has different definitions in different filed. Therefore, the measure of privacy preserving data mining technology protecting private information is not the same. So, it's an urgent issue to present a unified privacy definition and measure. Secondly, the most of research in privacy preserving data mining is presently confined to the theory study.

Roadway backfill method to prevent geohazards induced by room and pillar mining: a case study in Changxing coal mine, China

NASA Astrophysics Data System (ADS)

Zhou, Nan; Li, Meng; Zhang, Jixiong; Gao, Rui

2016-11-01

Coal mines in the western areas of China experience low mining rates and induce many geohazards when using the room and pillar mining method. In this research, we proposed a roadway backfill method during longwall mining to target these problems. We tested the mechanical properties of the backfill materials to determine a reasonable ratio of backfill materials for the driving roadway during longwall mining. We also introduced the roadway layout and the backfill mining technique required for this method. Based on the effects of the abutment stress from a single roadway driving task, we designed the distance between roadways and a driving and filling sequence for multiple-roadway driving. By doing so, we found the movement characteristics of the strata with quadratic stabilization for backfill mining during roadway driving. Based on this research, the driving and filling sequence of the 3101 working face in Changxing coal mine was optimized to avoid the superimposed influence of mining-induced stress. According to the analysis of the surface monitoring data, the accumulated maximum subsidence is 15 mm and the maximum horizontal deformation is 0.8 mm m-1, which indicated that the ground basically had no obvious deformation after the implementation of the roadway backfill method at 3101 working face.

Analysis of mesenchymal stem cell differentiation in vitro using classification association rule mining.

PubMed

Wang, Weiqi; Wang, Yanbo Justin; Bañares-Alcántara, René; Coenen, Frans; Cui, Zhanfeng

2009-12-01

In this paper, data mining is used to analyze the data on the differentiation of mammalian Mesenchymal Stem Cells (MSCs), aiming at discovering known and hidden rules governing MSC differentiation, following the establishment of a web-based public database containing experimental data on the MSC proliferation and differentiation. To this effect, a web-based public interactive database comprising the key parameters which influence the fate and destiny of mammalian MSCs has been constructed and analyzed using Classification Association Rule Mining (CARM) as a data-mining technique. The results show that the proposed approach is technically feasible and performs well with respect to the accuracy of (classification) prediction. Key rules mined from the constructed MSC database are consistent with experimental observations, indicating the validity of the method developed and the first step in the application of data mining to the study of MSCs.

Destruction processes of mining on water environment in the mining area combining isotopic and hydrochemical tracer.

PubMed

Yang, Yonggang; Guo, Tingting; Jiao, Wentao

2018-06-01

There is less research on the hydrological system and its destruction processes mechanism in the mining areas, especially combined application of isotope technology and chemical signals, which is a key scientific problem that need to be solved. This study takes Jinci spring area in Shanxi as a case study. It is based on the data of hydrology and mining condition from 1954 to 2015, combining monitoring experiments, O 18 , D, S 34 and N 15 tracing, chemical and model simulation. This study investigates the hydrological regularity and impacts of mining activities on water quantity and quality, and reveals the destruction process of hydrological system. The results show that: (1) Water chemical type shows an evolutionary trend of HCO 3 - -Ca 2+ -Mg 2+ →SO 4 2- -HCO 3 - -Ca 2+ -Mg 2+ →SO 4 2- -Ca 2+ -Mg 2+ , due to the influence of exploitation and fault zones. Isotope tracer shows that mine pit water is formed by a mixture of pore water, karst water and surface water. (2) Although precipitation and seepage have a certain impact on the reducing of groundwater quantity, over-exploitation of water resource is still the main reason for reducing of groundwater quantity. Under the conditions of keeping the exploitation intensity at the current level or reducing it by 10%, groundwater level shows a declining trend. Under the condition of reducing it by 30%, groundwater level starts to rise up. When reducing by 50%, groundwater level reaches its highest point. Coalmining changes the runoff, recharge and discharge paths. (3) From 1985 to 2015, Water quality in the mining area is worsening. Ca 2+ increases by 35.30%, SO 4 2- increases by 52.80%, and TDS (Total Dissolved Solid) increases by 67.50%. Nitrates come from the industrial and domestic wastewater, which is generated by mining. The percentage of groundwater coming from gypsum dissolusion is 67.51%, and the percentage from coal measure strata water is 34.49%. The water qualities of river branches are generally deteriorated. Copyright © 2018 Elsevier Ltd. All rights reserved.

In situ bioassays with Chironomus riparius larvae to biomonitor metal pollution in rivers and to evaluate the efficiency of restoration measures in mine areas.

PubMed

Faria, Mafalda S; Lopes, Ricardo J; Malcato, João; Nogueira, António J A; Soares, Amadeu M V M

2008-01-01

In this study we evaluate the ability of an in situ bioassay with Chironomus riparius larvae, using larval development and growth as endpoints, to biomonitor water quality and to assess the biological recovery of metal contaminated freshwater ecosystems of mine areas that are subject of restoration measures. The bioassay was carried out in streams located near an abandoned goldmine in North Portugal, throughout an environmental rehabilitation of the mine (2002-2004). During this period, a decrease in the inhibition of larval growth in the metal contaminated stream was observed. The bioassay was also performed in streams located near an active tungsten mine in Central Portugal. Larval growth and development were highly inhibited in the stream that receives acid drainage from the tungsten mine and treated water from the AMD treatment station. The results indicate that the bioassay can be used to evaluate the efficiency of environmental restoration measures in mining areas.

Determining a pre-mining radiological baseline from historic airborne gamma surveys: a case study.

PubMed

Bollhöfer, Andreas; Beraldo, Annamarie; Pfitzner, Kirrilly; Esparon, Andrew; Doering, Che

2014-01-15

Knowing the baseline level of radioactivity in areas naturally enriched in radionuclides is important in the uranium mining context to assess radiation doses to humans and the environment both during and after mining. This information is particularly useful in rehabilitation planning and developing closure criteria for uranium mines as only radiation doses additional to the natural background are usually considered 'controllable' for radiation protection purposes. In this case study we have tested whether the method of contemporary groundtruthing of a historic airborne gamma survey could be used to determine the pre-mining radiological conditions at the Ranger mine in northern Australia. The airborne gamma survey was flown in 1976 before mining started and groundtruthed using ground gamma dose rate measurements made between 2007 and 2009 at an undisturbed area naturally enriched in uranium (Anomaly 2) located nearby the Ranger mine. Measurements of (226)Ra soil activity concentration and (222)Rn exhalation flux density at Anomaly 2 were made concurrent with the ground gamma dose rate measurements. Algorithms were developed to upscale the ground gamma data to the same spatial resolution as the historic airborne gamma survey data using a geographic information system, allowing comparison of the datasets. Linear correlation models were developed to estimate the pre-mining gamma dose rates, (226)Ra soil activity concentrations, and (222)Rn exhalation flux densities at selected areas in the greater Ranger region. The modelled levels agreed with measurements made at the Ranger Orebodies 1 and 3 before mining started, and at environmental sites in the region. The conclusion is that our approach can be used to determine baseline radiation levels, and provide a benchmark for rehabilitation of uranium mines or industrial sites where historical airborne gamma survey data are available and an undisturbed radiological analogue exists to groundtruth the data. © 2013.

Long-term response of an arctic fiord system to lead-zinc mining and submarine disposal of mine waste (Maarmorilik, West Greenland).

PubMed

Søndergaard, Jens; Asmund, Gert; Johansen, Poul; Rigét, Frank

2011-06-01

Contamination by lead (Pb) and zinc (Zn) was studied in seawater, sediments, seaweeds and blue mussels near the former Black Angel Pb-Zn Mine in Maarmorilik, West Greenland. The mine operated during the period 1973-90 when mine waste (tailings and later waste rock) was discharged directly into the sea. Metal concentrations peaked during the mining period and Pb and Zn in seawater within the discharge area were measured up to 440 and 790 μg L⁻¹, respectively. Pb in fiord sediments, seaweeds and blue mussels just outside the discharge area were measured in concentrations up to 190, 84 and 2650 and Zn up to 300, 360 and 1190 μg g⁻¹ dry wt., respectively. Within the discharge area, seawater metal concentrations (especially Pb) decreased abruptly after mine closure. Metals concentrations in sediments and biota, however, decreased more slowly and two decades after mine closure seaweeds and blue mussels were still contaminated 12 km from the mine. Copyright © 2011 Elsevier Ltd. All rights reserved.

Geological survey of Maryland using EREP flight data. [mining, mapping, Chesapeake Bay islands, coastal water features

NASA Technical Reports Server (NTRS)

Weaver, K. N. (Principal Investigator)

1973-01-01

The author has identified the following significant results. Underflight photography has been used in the Baltimore County mined land inventory to determine areas of disturbed land where surface mining of sand and ground clay, or stone has taken place. Both active and abandoned pits and quarries were located. Aircraft data has been used to update cultural features of Calvert, Caroline, St. Mary's, Somerset, Talbot, and Wicomico Counties. Islands have been located and catalogued for comparison with older film and map data for erosion data. Strip mined areas are being mapped to obtain total area disturbed to aid in future mining and reclamation problems. Coastal estuarine and Atlantic Coast features are being studied to determine nearshore bedforms, sedimentary, and erosional patterns, and manmade influence on natural systems.

The influence of sand mining towards the sustainability of power support and capacity of Lambidaro River

NASA Astrophysics Data System (ADS)

Juniah, Restu; Rahmi, Hisni

2017-11-01

Activities of sand mining on the surface stream (river) conducted by Panji Mahakarya company potentially cause various environmental issues. These problems include the destruction of the river ecosystem, decreased the quality of river water quality, increased water pollution load, and another effect on capacity and power support river. The Lambidaro River is one of the rivers found in Palembang, where the inhabitants who live around it take advantage of the existence of this river to meet their daily needs such as bathing, washing, and latrines. The purpose of this research is to know the influence of mining activities towards sustainability of the power support and capacity of the river. The method used in this research is to compare the availability of water and water needs of the population in determining the status of environmental power support based on regulation of the state minister of the environment number 17 in 2009 about the determination of the power guidance support environment in spatial regions, as well as using the index method of pollution based on the decision of the State Minister of the environment number 115 in 2003 about the determination of the status of water quality guidelines with parameters measured are TDS, TSS, pH, DO, COD, dan BOD5. The results of the calculation of the power support river are deficit where SA (34,200,655.64 m3/year) < DA (253,105,600 m3/year). The result of pollution index calculation at 5 water sampling locations shows that the condition of a river is in good condition (uncontaminated) and mild pollutant.

Assessment of geochemical and hydrologic conditions near Old Yuma Mine in Saguaro National Park, Arizona, 2014–17

USGS Publications Warehouse

Beisner, Kimberly R.; Gray, Floyd

2018-03-13

The Old Yuma Mine is an abandoned copper, lead, zinc, silver, and gold mine located within the boundaries of Saguaro National Park, Tucson Mountain District, Arizona. This study analyzed the geochemistry of sediments associated with the Old Yuma Mine and assessed hydrologic and geochemical conditions of groundwater to evaluate the area surrounding the Old Yuma Mine. The purpose of the study was to establish the geochemical signature of material associated with the Old Yuma Mine and to compare it with background material and groundwater in the area. Few groundwater samples exceeded the U.S. Environmental Protection Agency (EPA) drinking water standards. Concentrations of several elements were elevated in the waste rock and mine tailings compared with concentrations in sediments collected in background areas. A subset of 15 sediment samples was leached to simulate precipitation interacting with the solid material. Analysis of leachate samples compared to groundwater samples suggests that groundwater samples collected in this study are distinct from leachate samples associated with mining related material. Results suggest that at this time groundwater samples collected during this investigation are not influenced by elements leached from Old Yuma Mine materials.

43 CFR 3930.12 - Performance standards for underground mining.

Code of Federal Regulations, 2014 CFR

2014-10-01

... reserves. (c) Operators/lessees must adopt measures consistent with known technology to prevent or, where the mining method used requires subsidence, control subsidence, maximize mine stability, and maintain... temporarily abandon a mine or portions thereof. (e) The operator/lessee must have the BLM's prior approval to...

43 CFR 3930.12 - Performance standards for underground mining.

Code of Federal Regulations, 2013 CFR

2013-10-01

... reserves. (c) Operators/lessees must adopt measures consistent with known technology to prevent or, where the mining method used requires subsidence, control subsidence, maximize mine stability, and maintain... temporarily abandon a mine or portions thereof. (e) The operator/lessee must have the BLM's prior approval to...

43 CFR 3930.12 - Performance standards for underground mining.

Code of Federal Regulations, 2012 CFR

2012-10-01

... reserves. (c) Operators/lessees must adopt measures consistent with known technology to prevent or, where the mining method used requires subsidence, control subsidence, maximize mine stability, and maintain... temporarily abandon a mine or portions thereof. (e) The operator/lessee must have the BLM's prior approval to...

43 CFR 3930.12 - Performance standards for underground mining.

Code of Federal Regulations, 2011 CFR

2011-10-01

... reserves. (c) Operators/lessees must adopt measures consistent with known technology to prevent or, where the mining method used requires subsidence, control subsidence, maximize mine stability, and maintain... temporarily abandon a mine or portions thereof. (e) The operator/lessee must have the BLM's prior approval to...

Passive Treatment And Monitoring At The Standard Mine Superfund Site, Crested Butte, CO (Presentation)

EPA Science Inventory

At the 2008 ASMR conference, data from the initial two months of operation of a U.S. EPA pilot biochemical reactor (BCR) was reported. The BCR was designed and constructed in August, 2007 to treat mining influenced water (MIW) emanating from an adit at a remote site in southern ...

Passive Treatment And Monitoring At The Standard Mine Superfund Site, Crested Butte, CO

EPA Science Inventory

At the 2008 ASMR conference, data from the initial two months of operation of a U.S. EPA pilot biochemical reactor (BCR) was reported. The BCR was designed and constructed in August, 2007 to treat mining influenced water (MIW) emanating from an adit at a remote site in southern ...

Stream biological surveys - self-defense for coal mine operators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hampton, E.L.; Pennington, W.L.; Lackey, J.L.

1979-12-01

According to Section 779.20 of the Permanent Regulatory Program Regulations, Surface Coal Mining and Reclamation Operations, Department of the Interior, office of Surface Mining Reclamation and Enforcement, coal mine operators must provide information on fish and wildlife resources in order to obtain mining permits. Although considered to be a liability by many mine operators, stream biological surveys can, in reality, become a significant asset. When combined with appropriate water quality measurements, stream biological surveys can adequately assess a stream's health. Although initially adding cost, stream biological surveys can actually save money and potential litigation during the mining period. However, streammore » biological surveys must be conducted before any mining activity is initiated and should continue on a periodic basis thereafter. Only in this manner can mine operators be assured that biological measurements made on streams affected by their operation are accurate reflections of pre- and post-mining conditions. Armed with this vital information, mine operators have a basis to defend against any unjustified claims that their operations are having deleterious effects on the stream in question. This paper addresses the purpose, scope, methodology, and interpretation of results of stream biological surveys. Additionally, methods for utilizing information from stream biological surveys will be stressed.« less

Novel speciation method based on Diffusive Gradients in Thin Films for in situ measurement of uranium in the vicinity of the former uranium mining sites.

PubMed

Drozdzak, Jagoda; Leermakers, Martine; Gao, Yue; Phrommavanh, Vannapha; Descostes, Michael

2016-07-01

The Diffusive Gradients in Thin Films (DGT) technique using PIWBA resin (The Dow Chemical Company) was developed and validated for the measurement of uranium (U) concentration in natural and uranium mining influenced waters. The U uptake on the PIWBA resin gel was 97.3 ± 0.4% (batch method; Vsol = 5 mL; [U] = 20 μg L(-1); 0.01 M NaNO3; pH = 7.0 ± 0.2). The optimal eluent was found to be HNO3conc/70 °C with an elution efficiency of 88.9 ± 1.4%. The laboratory DGT investigation demonstrated that the PIWBA resin gel exhibits a very good performance across a wide range of pH (3-9) and ionic strength (0.001-0.7 M NaNO3) at different time intervals. Neither effect of PO4(3-) (up to 1.72 × 10(-4) M), nor of HCO3(-) (up to 8.20 × 10(-3) M) on the quantitative measurement of uranium by DGT-PIWBA method were observed. Only at very high Ca(2+) (2.66 × 10(-4) M), and SO4(2-) (5.55 × 10(-4) M) concentration, the U uptake on DGT-PIWBA was appreciably lessened. In-situ DGT field evaluation was carried out in the vicinity of three former uranium mining sites in France (Loire-Atlantique and Herault departments), which employ different water treatment technologies and have different natural geochemical characteristics. There was a similar or inferior U uptake on DGT-Chelex(®)-100 in comparison with the U accumulation on a DGT-PIWBA sampler. Most likely, the performance of Chelex(®)-100 was negatively affected by a highly complex matrix of mining waters. The high concentration and identity of co-accumulating analytes, typical for the mining environment, did not have a substantial impact on the quantitative uptake of labile U species on DGT- PIWBA. The use of the polyphenol impregnated anion exchange resin leads to a significant advancement in the application and development of the DGT technique for determination of U in the vicinity of the former uranium mining sites. Copyright © 2016 Elsevier Ltd. All rights reserved.

30 CFR 819.21 - Auger mining: Protection of underground mining.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., DEPARTMENT OF THE INTERIOR PERMANENT PROGRAM PERFORMANCE STANDARDS SPECIAL PERMANENT PROGRAM PERFORMANCE... closer than 500 feet (measured horizontally) to any abandoned or active underground mine workings, except...

NEW IMPROVEMENTS TO MFIRE TO ENHANCE FIRE MODELING CAPABILITIES.

PubMed

Zhou, L; Smith, A C; Yuan, L

2016-06-01

NIOSH's mine fire simulation program, MFIRE, is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines, which has been used by U.S. and international companies to simulate fires for planning and response purposes. MFIRE is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence such as changes in ventilation parameters, external influences such as changes in temperature, and internal influences such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the Bureau of Mines in the 1970s, several updates have been released over the years. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE's outdated FORTRAN programming language was replaced with an object-oriented C++ language and packaged into a dynamic link library (DLL). However, the MFIRE 3.0 release made no attempt to change or improve the fire modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of fire source models of the t-squared fire and heat release rate curve data file, the addition of a moving fire source for conveyor belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke rollback phenomena. All the improvements discussed in this paper will be termed as MFIRE 3.1 and released by NIOSH in the near future.

Influence of Applying Additional Forcing Fans for the Air Distribution in Ventilation Network

NASA Astrophysics Data System (ADS)

Szlązak, Nikodem; Obracaj, Dariusz; Korzec, Marek

2016-09-01

Mining progress in underground mines cause the ongoing movement of working areas. Consequently, it becomes necessary to adapt the ventilation network of a mine to direct airflow into newly-opened districts. For economic reasons, opening new fields is often achieved via underground workings. Length of primary intake and return routes increases and also increases the total resistance of a complex ventilation network. The development of a subsurface structure can make it necessary to change the air distribution in a ventilation network. Increasing airflow into newly-opened districts is necessary. In mines where extraction does not entail gas-related hazards, there is possibility of implementing a push-pull ventilation system in order to supplement airflows to newly developed mining fields. This is achieved by installing subsurface fan stations with forcing fans at the bottom of downcast shaft. In push-pull systems with multiple main fans, it is vital to select forcing fans with characteristic curves matching those of the existing exhaust fans to prevent undesirable mutual interaction. In complex ventilation networks it is necessary to calculate distribution of airflow (especially in networks with a large number of installed fans). In the article the influence of applying additional forcing fans for the air distribution in ventilation network for underground mine were considered. There are also analysed the extent of overpressure caused by the additional forcing fan in branches of the ventilation network (the operating range of additional forcing fan). Possibilities of increasing airflow rate in working areas were conducted.

Dispersion and bioaccumulation of elements from an open-pit olivine mine in Southwest Greenland assessed using lichens, seaweeds, mussels and fish.

PubMed

Søndergaard, Jens

2013-08-01

This study investigated dispersion and bioaccumulation of mining-related elements from an open-pit olivine mine at Seqi in Southwest Greenland (64° N) using lichens (Flavocetraria nivalis), seaweeds (Fucus vesiculosus), mussels (Mytilus edulis) and fish (Myoxocephalus scorpius). The mine operated between 2005 and 2009, and samples were taken every year within a monitoring area 0-17 km from the mine during the period 2004-2011. A total of 46 elements were analysed in the samples. After mining began, highly elevated metal concentrations, especially nickel (Ni), chromium (Cr), iron (Fe) and cobalt (Co), were observed in lichens relative to pre-mining levels (up to a factor of 130) caused by dust dispersion from the mining activity. Elevated metal concentrations could be measured in lichens in distances up to ~5 km from the mine/ore treatment facility. Moderately elevated concentrations of Ni and Cr (up to a factor of 7) were also observed in seaweeds and mussels but only in close vicinity (<1 km) to the mine. Analyses of fish showed no significant changes in element composition. After mine closure, the elevated metal concentrations in lichens, seaweeds and mussels decreased markedly, and in 2011, significantly elevated metal concentrations could only be measured in lichens and only within a distance of 1 km from the mine.

Ultrawideband radar echoes of land mine targets measured at oblique incidence using a 250-kW impulse radar system

NASA Astrophysics Data System (ADS)

Chant, Ian J.; Staines, Geoff

1997-07-01

United Nations Peacekeeping forces around the world need to transport food, personnel and medical supplies through disputed regions were land mines are in active use as road blocks and terror weapons. A method of fast, effective land mine detection is needed to combat this threat to road transport. The technique must operate from a vehicle travelling at a reasonable velocity and give warning far enough ahead for the vehicle to stop in time to avoid the land mine. There is particular interest in detecting low- metallic content land mines. One possible solutionis the use of ultra-wide-band (UWB) radar. The Australian Defence Department is investigating the feasibility of using UWB radar for land mine detection from a vehicle. A 3 GHz UWB system has been used to collect target response from a series of inert land mines and mine-like objects placed on the ground and buried in the ground. The targets measured were a subset of those in the target set described in Wong et al. with the addition of inert land mines corresponding to some of the surrogate targets in this set. The results are encouraging for the detection of metallic land mines and the larger non-metallic land mines. Smaller low-metallic- content anti-personnel land mines are less likely to be detected.

43 CFR 3484.1 - Performance standards for exploration and surface and underground mining.

Code of Federal Regulations, 2014 CFR

2014-10-01

... officer. Operators/lessees of underground coal mines shall adopt measures consistent with known technology... subsequent operations on the quantity, quality, or pressure of ground water or mine gases only with the... mines—(1) Underground resource recovery. Underground mining operations shall be conducted so as to...

43 CFR 3484.1 - Performance standards for exploration and surface and underground mining.

Code of Federal Regulations, 2011 CFR

2011-10-01

... officer. Operators/lessees of underground coal mines shall adopt measures consistent with known technology... subsequent operations on the quantity, quality, or pressure of ground water or mine gases only with the... mines—(1) Underground resource recovery. Underground mining operations shall be conducted so as to...

30 CFR 90.3 - Part 90 option; notice of eligibility; exercise of option.

Code of Federal Regulations, 2014 CFR

2014-07-01

... as measured by the Mining Research Establishment (MRE) instrument. When the approved sampling device... concentrations. Mechanized mining unit (MMU). A unit of mining equipment including hand loading equipment used for the production of material; or a specialized unit which uses mining equipment other than specified...

Distribution of 226Ra body burden of workers in an underground uranium mine in India.

PubMed

Patnaik, R L; Jha, V N; Kumar, R; Srivastava, V S; Ravi, P M; Tripathi, R M

2014-11-01

Uranium mine workers are exposed to ore dust containing uranium and its daughter products during different mining operations. These radionuclides may pose inhalation hazards to workers during the course of their occupation. The most significant among these radionuclides is (226)Ra. The measurement of radium body burden of uranium mine workers is important to assess their internal exposure. For this purpose, the radon-in-breath measurement technique has been used in the present paper. Workers at the Jaduguda mine, India, associated with different categories of mining operations were monitored between 2001 and 2007. The measurement results indicate that workers--depending on mining operation category--show (226)Ra body burdens ranging from 0.15 to 2.85 kBq. The maximum body burden was found for workers associated with timbering operations, with an average (226)Ra body burden of 0.85 ± 0.54 kBq. Overall, the average value observed for 800 workers was 0.76 ± 0.51 kBq, which gives rise to an average effective dose of 1.67 mSv per year for inhalation and 0.21 mSv per year for ingestion.

Application of the Gmc-1000 and Gmc-2000 Mine Cooling Units for Central Air-Conditioning in Underground Mines / Zastosowanie górniczego urządzenia chłodniczego gmc-1000 i gmc-2000 w centralnej klimatyzacji kopalń podziemnych

NASA Astrophysics Data System (ADS)

Wojciechowski, Jerzy

2013-03-01

The paper describes the design and results of operating measurements of the GMC-1000 and GMC- 2000 Mine Cooling Units. The first part describes the design of the cooling unit and its key components: the chiller, evaporator, condenser, oil cooler, evaporative water cooler and gallery air cooler. The possibilities of use in central air conditioning systems of underground mines are described. The second part discusses the results of the workstation and operating measurements and determines the coefficients for evaluating the performance of the mine cooling unit.

Hydrochemical and environmental isotope analysis of groundwater and surface water in a dry mountain region in Northern Chile.

PubMed

Zang, Carina; Dame, Juliane; Nüsser, Marcus

2018-05-08

This case study examines the geological imprint and land use practices on water quality in the arid Huasco Valley against the backdrop of ongoing water conflicts surrounding competing demands for agriculture and mining. The study is based on a detailed analysis of spatial and temporal variations of monthly surface and bi-monthly groundwater quality samples measured during the Chilean summer of 2015/16. Additional information on source regions and river-groundwater interactions were collected using stable water isotopes. Regarding the geological impact on water quality, high concentrations of Ca 2+ , SO 4 2- and HCO 3 - indicate a strong influence of magmatic rocks, which constitute this high mountain basin, on the hydrochemistry. Piper and Gibbs-diagrams revealed that all samples show a homogenous distribution dominated by rock-water interactions. Measured NO 3 - concentrations in surface water are generally low. However, groundwater aquifers exhibit higher concentrations. Mn is the only heavy metal with elevated concentrations in surface water, which are possibly related to mining activities. The results illustrate that both surface and groundwater can be classified as suitable for irrigation. In addition, groundwater has been found to be suitable as drinking water. High similarities in isotopic signatures indicate a strong connection between surface and groundwater. Isotopic analyses suggest a strong influence of evaporation. This combined approach of hydrogeochemical and isotopic analysis proved to be a helpful tool in characterizing the catchment and can serve as a basis for future sustainable water management.

The analysis of the Tectonics - SSS - Seismicity System in the 3D-model of the Rasvumchorr Mine - Central Open Pit Natural and Technical System (Khibiny)

NASA Astrophysics Data System (ADS)

Zhirov, Dmitry; Klimov, Sergey; Zhirova, Anzhela; Panteleev, Alexey; Rybin, Vadim

2017-04-01

Main hazardous factors during the operation of deposits represent tectonics (structural dislocation), strain and stress state (SSS), and seismicity. The cause and effect relationships in the Fault Tectonics - SSS - Seismicity system were analyzed using a 3D geological and structural Rasvumchorr Mine - Central Open Pit model. This natural and technical system (NTS) has resulted from the development of the world-class apatite-nepheline deposits the Apatite Circus and Rasvumchorr Plateau. The 3D model integrates various spatial data on the earth's surface topography before and after mining, geometry of mines and dumps, SSS measurements and rock pressure, seismicity, fault tectonics and etc. The analysis of the 3D model has clearly demonstrated the localization of three main seismic emanation zones in the areas of maximum anthropogenic variation of the initial rock state, and namely: ore pass zone under the Southern edge of the Central open pit, collapse and joining zone of the Rasvumchorr Mine and NW edge of the open pit, and zone under the Apatite Circus plate - collapse console. And, on the contrary, in the area of a large dump under the underground mine, a perennial seismic minimum zone was identified. The relation of the seismicity and fault tectonics was revealed only in three local sectors near come certain echelon fissures of the Main Fault(MF). No confinement of increased seismicity areas to the MF and other numerous echelon fissures is observed. The same picture occurs towards manifestations of rock pressure. Only an insignificant part of echelon fissures (including low rank of hierarchy) controls hazardous manifestations of rock pressure (dumps, strong deformations of the mine contour, etc.). It is shown that the anthropogenic factor (explosive, geometry and arrangement of mined spaces and collapse console), as well as the time factor significantly change orientation and structure (contrast and heterogeneity) of the stress fields. Time series of natural geophysical field fluctuations were additionally analyzed in order to find relationships with the seismicity. A sustainable regular relationship between the seismicity and solar and lunar tides has been observed; though, medium (classes 3 to 6) and high (class 7 and above) energy values of the events reveal various symmetry towards the Lunar cycle phases. The relationship of seismicity with other geophysical fields, e.g., geomagnetic disturbances, is defined as weak to very weak. The anthropogenic (man-induced) factor mostly influences the seismicity in the NTS rock masses. A law for shifting of maximum seismicity zones following the advance of the mining front has been found. The 3D model integrates various spatial data on the earth's surface topography before and after mining, geometry of mines and dumps, SSS measurements, and rock pressure, seismicity, fault tectonics, and other manifestations. The study is made within R&D topic No. 0231-2015-0013. The collection, processing, and analysis of data for natural stress fields became possible due to the support from RSF grant 14-17-00751.

Temporal and spatial changes of land use and landscape in a coal mining area in Xilingol grassland

NASA Astrophysics Data System (ADS)

Guan, Chunzhu; Zhang, Baolin; Li, Jiannan; Zhao, Junling

2017-01-01

Coal mining, particularly surface mining, inevitably disturbs land. According to Landsat images acquired over Xilingol grassland in 2005, 2009 and 2015, land uses were divided into seven classes, i. e., open stope, stripping area, waste-dump area, mine industrial area, farmland, urban area and the original landscape (grassland), using supervised classification and human-computer interactive interpretation. The overall classification accuracies were 97.72 %, 98.43 % and 96.73 %, respectively; the Kappa coefficients were 0.95, 0.97 and 0.95, respectively. Analysis on LUCC (Land Use and Cover Change) showed that surface coal mining disturbed grassland ecosystem: grassland decreased by 8661.15 hm2 in 2005-2015. The area and proportion of mining operation areas (open stope, stripping area, waste-dump area, mine industrial field) increased, but those of grassland decreased continuously. Transfer matrix of land use changes showed that waste-dump had the largest impacts in mining disturbance, and that effective reclamation of waste-dump areas would mitigate eco-environment destruction, as would be of great significance to protect fragile grassland eco-system. Six landscape index showed that landscape fragmentation increased, and the influences of human activity on landscape was mainly reflected in the expansion of mining area and urban area. Remote sensing monitoring of coal surface mining in grassland would accurately demonstrate the dynamics and trend of LUCC, providing scientific supports for ecological reconstruction in surface mining area.

The Effects of Elevated Specific Conductivity on the Chronic Toxicity of Mining Influenced Streams Using Ceriodaphnia dubia

PubMed Central

Armstead, Mindy Yeager; Bitzer-Creathers, Leah; Wilson, Mandee

2016-01-01

Salinization of freshwater ecosystems as a result of human activities has markedly increased in recent years. Much attention is currently directed at evaluating the effects of increased salinity on freshwater biota. In the Central Appalachian region of the eastern United States, specific conductance from alkaline discharges associated with mountain top mining practices has been implicated in macroinvertebrate community declines in streams receiving coal mining discharges. Whole effluent toxicity testing of receiving stream water was used to test the hypothesis that mine discharges are toxic to laboratory test organisms and further, that toxicity is related to ionic concentrations as indicated by conductivity. Chronic toxicity testing using Ceriodaphnia dubia was conducted by contract laboratories at 72 sites with a total of 129 tests over a 3.5 year period. The database was evaluated to determine the ionic composition of mine effluent dominated streams and whether discharge constituents were related to toxicity in C. dubia. As expected, sulfate was found to be the dominant anion in streams receiving mining discharges with bicarbonate variable and sometimes a substantial component of the dissolved solids. Overall, the temporal variability in conductance was low at each site which would indicate fairly stable water quality conditions. Results of the toxicity tests show no relationship between conductance and survival of C. dubia in the mining influenced streams with the traditional toxicity test endpoints. However, consideration of the entire dataset revealed a significant inverse relationship between conductivity and neonate production. While conductivity explained very little of the high variability in the offspring production (r2 = 0.1304), the average numbers of offspring were consistently less than 20 neonates at the highest conductivities. PMID:27814378

Empirical Models of Zones Protecting Against Coal Dust Explosion

NASA Astrophysics Data System (ADS)

Prostański, Dariusz

2017-09-01

The paper presents predicted use of research' results to specify relations between volume of dust deposition and changes of its concentration in air. These were used to shape zones protecting against coal dust explosion. Methodology of research was presented, including methods of measurement of dust concentration as well as deposition. Measurements were taken in the Brzeszcze Mine within framework of MEZAP, co-financed by The National Centre for Research and Development (NCBR) and performed by the Institute of Mining Technology KOMAG, the Central Mining Institute (GIG) and the Coal Company PLC. The project enables performing of research related to measurements of volume of dust deposition as well as its concentration in air in protective zones in a number of mine workings in the Brzeszcze Mine. Developed model may be supportive tool in form of system located directly in protective zones or as operator tool warning about increasing hazard of coal dust explosion.

Chemical analyses of water samples from the Picher mining area, northeast Oklahoma and southeast Kansas

USGS Publications Warehouse

Parkhurst, David L.

1987-01-01

Chemical analyses are presented for 169 water samples from Tar Creek drainage and the Picher lead-zinc mining area of northeast Oklahoma and southeast Kansas. Water samples were taken from November 1983 through February 1986 from the abandoned mines, from points of mine-water discharge, and from surface-water locations upstream and downstream from mine discharge area. The pH, temperature, alkalinity, dissolved oxygen, and specific conductance were measured in the field. Laboratory analyses routinely included the major ions plus aluminum, cadmium, copper, iron, lead, manganese, nickel, and zinc. Non-routine analyses of dissolved gases and tritium are presented. Stable carbon-isotope ratios for 11 mine-water samples and three carbonate-rock samples are reported. Miscellaneous stream-discharge measurements made at the time of sampling or taken from gaging-station records are included in the report.

Respirable dust measured downwind during rock dust application.

PubMed

Harris, M L; Organiscak, J; Klima, S; Perera, I E

2017-05-01

The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using untreated rock dust and rock dust treated with an anticaking additive. Using personal dust monitors, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH's Bruceton Experimental Mine using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners' exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device.

Coastal Benthic Optical Properties Fluorescence Imaging Laser Line Scan Sensor

DTIC Science & Technology

2001-09-30

Acquisition of Electro - Optic Identification (EOID) sensors for MLC identification is currently underway to support both Air Mine Counter-Measures (AMCM) and Surface Mine Counter-Measures (SMCM) operations.

Influences of coal mining water irrigation on the maize losses in the Xingdong Mine area, China.

PubMed

Sun, Yuzhuang; Ling, Pei; Li, Yanheng; Li, Qingxue; Sun, Quande; Wang, Jinxi

2014-02-01

In 2008, a maize underproduction disaster occurred in the Xianyu village after irrigation using the coal mining water from the Xingdong Mine, China. This disaster resulted in about 40 hectare maize underproduction and 20 hectare total loss of the maize yields. In order to study the reason, a total of 25 soil, water and plant samples were taken from the study area. These samples were analysed by inductively coupled plasma mass spectrometry and ion chromatography. The results indicate that the contents of both water-soluble fluorine and total fluorine are very high and resulting of maize underproduction and total loss of production. The possible pollution sources of fluorine in the study area could be from the coal mine water used for irrigation and glass chemical factory near the study area.

Impact of Coal Mining on Self-Rated Health among Appalachian Residents

PubMed Central

Woolley, Shannon M.; Bear, Todd M.; Balmert, Lauren C.; Talbott, Evelyn O.; Buchanich, Jeanine M.

2015-01-01

Objective. To determine the impact of coal mining, measured as the number of coal mining-related facilities nearby one's residence or employment in an occupation directly related to coal mining, on self-rated health in Appalachia. Methods. Unadjusted and adjusted ordinal logistic regression models calculated odds ratio estimates and associated 95% confidence intervals for the probability of having an excellent self-rated health response versus another response. Covariates considered in the analyses included number of coal mining-related facilities nearby one's residence and employment in an occupation directly related to coal mining, as well as potential confounders age, sex, BMI, smoking status, income, and education. Results. The number of coal mining facilities near the respondent's residence was not a statistically significant predictor of self-rated health. Employment in a coal-related occupation was a statistically significant predictor of self-rated health univariably; however, after adjusting for potential confounders, it was no longer a significant predictor. Conclusions. Self-rated health does not seem to be associated with residential proximity to coal mining facilities or employment in the coal industry. Future research should consider additional measures for the impact of coal mining. PMID:26240577

The Construction And Instrumentation Of A Pilot Treatment System At The Standard Mine Superfund Site, Crested Butte, CO

EPA Science Inventory

A pilot biochemical reactor (BCR) was designed and constructed to treat mine-influenced water emanating from an adit at a remote site in southern Colorado which receives an average of 400 inches (10.2 meters) of snowfall each season. The objective of the study is to operate and ...

The Construction And Instrumentation Of A Pilot Treatment System At The Standard Mine Superfund Site, Crested Butte, CO - (Presentation)

EPA Science Inventory

A pilot biochemical reactor (BCR) was designed and constructed to treat mine-influenced water emanating from an adit at a remote site in southern Colorado which receives an average of 400 inches (10.2 meters) of snowfall each season. The objective of the study is to operate and ...

Invasion of a mined landscape: what habitat characteristics are influencing the occurrence of invasive plants?

Treesearch

D. Lemke; I.A. Tazisong; Y. Wang; J.A. Brown

2012-01-01

Throughout the world, the invasion of alien plants is an increasing threat to native biodiversity. Invasion is especially prevalent in areas affected by land transformation and anthropogenic disturbance. Surface mines are a major disturbance, and thus may promote the establishment and expansion of invasive plant communities. Environmental and habitat factors that may...

Facilitation of American chestnut (Castanea dentata) seedling establishment by Pinus virginiana in mine restoration

Treesearch

Jenise M. Bauman; Carolyn H. Keiffer; Shiv Hiremath

2012-01-01

This study evaluated the influence of planting sites on the establishment and ectomycorrhizal (ECM) colonization of American chestnut (Castanea denetata (Marsh.) Borkh.) on an abandoned coal mine in an Appalachian region of the United States. Root morphotyping and sequencing of the fungal internal transcribed spacer (ITS) region were used to identify...

Assessing Lost Ecosystem Service Benefits Due to Mining-Induced Stream Degradation in the Appalachian Region: Economic Approaches to Valuing Recreational Fishing Impacts

EPA Science Inventory

Sport fishing is a popular activity for Appalachian residents and visitors. The region’s coldwater streams support a strong regional outdoor tourism industry. We examined the influence of surface coal mining, in the context of other stressors, on freshwater sport fishing in...

What Satisfies Students? Mining Student-Opinion Data with Regression and Decision-Tree Analysis. AIR 2002 Forum Paper.

ERIC Educational Resources Information Center

Thomas, Emily H.; Galambos, Nora

To investigate how students' characteristics and experiences affect satisfaction, this study used regression and decision-tree analysis with the CHAID algorithm to analyze student opinion data from a sample of 1,783 college students. A data-mining approach identifies the specific aspects of students' university experience that most influence three…

The Raising Influence of Information Technologies on Professional Training in the Sphere of Automated Driving When Transporting Mined Rock

NASA Astrophysics Data System (ADS)

Kosolapov, Andrey; Krysin, Sergey

2017-11-01

Revolutionary changes in the area of production, holding and exploitation of the automobile as a transport vehicle are analyzed in the article. Current state of the issue is described and the development stages of new approach to driving without human participation are predicted, taking into consideration the usage of automobiles for transportation of mined rock in Kuzbass. The influence of modern information technologies on the development of new sector of automobile industry and on the process of professional and further training of the specialists in the sphere of automobile driving is considered.

Identification of Social and Environmental Conflicts Resulting from Open-Cast Mining

NASA Astrophysics Data System (ADS)

Górniak-Zimroz, Justyna; Pactwa, Katarzyna

2016-10-01

Open-cast mining is related to interference in the natural environment. It also affects human health and quality of life. This influence is, among others, dependent on the type of extracted materials, size of deposit, methods of mining and mineral processing, as well as, equally important, sensitivity of the environment within which mining is planned. The negative effects of mining include deformations of land surface or contamination of soils, air and water. What is more, in many cases, mining for minerals leads to clearing of housing and transport infrastructures located within the mining area, a decrease in values of the properties in the immediate vicinity of a deposit, and an increase in stress levels in local residents exposed to noise. The awareness of negative consequences of taking up open-cast mining activity leads to conflicts between a mining entrepreneur and self-government authorities, society or nongovernment organisations. The article attempts to identify potential social and environmental conflicts that may occur in relation to a planned mining activity. The results of the analyses were interpreted with respect to the deposits which were or have been mined. That enabled one to determine which facilities exclude mineral mining and which allow it. The research took the non-energy mineral resources into consideration which are included in the group of solid minerals located in one of the districts of Lower Silesian Province (SW Poland). The spatial analyses used the tools available in the geographical information systems

Miners' return to work following injuries in coal mines.

PubMed

Bhattacherjee, Ashis; Kunar, Bijay Mihir

2016-12-22

The occupational injuries in mines are common and result in severe socio-economical consequences. Earlier studies have revealed the role of multiple factors such as demographic factors, behavioral factors, health-related factors, working environment, and working conditions for mine injuries. However, there is a dearth of information about the role of some of these factors in delayed return to work (RTW) following a miner's injury. These factors may likely include personal characteristics of injured persons and his or her family, the injured person's social and economic status, and job characteristics. This study was conducted to assess the role of some of these factors for the return to work following coal miners' injuries. A study was conducted for 109 injured workers from an underground coal mine in the years 2000-2009. A questionnaire, which was completed by the personnel interviews, included among others age, height, weight, seniority, alcohol consumption, sleeping duration, presence of diseases, job stress, job satisfaction, and injury type. The data was analyzed using the Kaplan-Meier estimates and the Cox proportional hazard model. According to Kaplan-Meier estimate it was revealed that a lower number of dependents, longer sleep duration, no job stress, no disease, no alcohol addiction, and higher monthly income have a great impact on early return to work after injury. The Cox regression analysis revealed that the significant risk factors which influenced miners' return to work included presence of disease, job satisfaction and injury type. The mine management should pay attention to significant risk factors for injuries in order to develop effective preventive measures. Med Pr 2016;67(6):729-742. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

Air pollutant intrusion into the Wieliczka Salt Mine

USGS Publications Warehouse

Salmon, L.G.; Cass, G.R.; Kozlowski, R.; Hejda, A.; Spiker, E. C.; Bates, A.L.

1996-01-01

The Wieliczka Salt Mine World Cultural Heritage Site contains many rock salt sculptures that are threatened by water vapor condensation from the mine ventilation air. Gaseous and particulate air pollutant concentrations have been measured both outdoors and within the Wieliczka Salt Mine, along with pollutant deposition fluxes to surfaces within the mine. One purpose of these measurements was to determine whether or not low deliquescence point ionic materials (e.g., NH4NO3) are accumulating on surfaces to an extent that would exacerbate the water vapor condensation problems in the mine. It was found that pollutant gases including SO2 and HNO3 present in outdoor air are removed rapidly and almost completely from the air within the mine by deposition to surfaces. Sulfur isotope analyses confirm the accumulation of air pollutant-derived sulfur in liquid dripping from surfaces within the mine. Particle deposition onto interior surfaces in the mine is apparent, with resulting soiling of some of those sculptures that have been carved from translucent rock salt. Water accumulation by salt sculpture surfaces was studied both experimentally and by approximate thermodynamic calculations. Both approaches suggest that the pollutant deposits on the sculpture surfaces lower the relative humidity (RH) at which a substantial amount of liquid water will accumulate by 1% to several percent. The extraordinarily low SO2 concentrations within the mine may explain the apparent success of a respiratory sanatorium located deep within the mine.

Sand and gravel mining: effects on ground water resources in Hancock county, Maine, USA

NASA Astrophysics Data System (ADS)

Peckenham, John M.; Thornton, Teresa; Whalen, Bill

2009-01-01

Based on this preliminary study, existing sand and gravel mining regulations (in Maine, USA) can be inferred to provide some protection to water resources. Sand and gravel deposits are important natural resources that have dual uses: mining for construction material and pumping for drinking water. How the mining of sand and gravel affects aquifers and change aquifer vulnerability to contamination is not well documented. Mining regulations vary greatly by state and local jurisdiction. This study test metrics to measure the effectiveness of mining regulations. The sand and gravel aquifer system studied is covered with former and active gravel pits to nearly 25% of its areal extent. Data from homeowner interviews and field measurements found scant evidence of changes in water quantity. Water quality analyses collected from springs, streams, ponds and wells indicate that the aquifer was vulnerable to contamination by chloride and nitrate. However, water quality changes can not be related directly to mining activities.

Evaluation of a Cubature Kalman Filtering-Based Phase Unwrapping Method for Differential Interferograms with High Noise in Coal Mining Areas

PubMed Central

Liu, Wanli; Bian, Zhengfu; Liu, Zhenguo; Zhang, Qiuzhao

2015-01-01

Differential interferometric synthetic aperture radar has been shown to be effective for monitoring subsidence in coal mining areas. Phase unwrapping can have a dramatic influence on the monitoring result. In this paper, a filtering-based phase unwrapping algorithm in combination with path-following is introduced to unwrap differential interferograms with high noise in mining areas. It can perform simultaneous noise filtering and phase unwrapping so that the pre-filtering steps can be omitted, thus usually retaining more details and improving the detectable deformation. For the method, the nonlinear measurement model of phase unwrapping is processed using a simplified Cubature Kalman filtering, which is an effective and efficient tool used in many nonlinear fields. Three case studies are designed to evaluate the performance of the method. In Case 1, two tests are designed to evaluate the performance of the method under different factors including the number of multi-looks and path-guiding indexes. The result demonstrates that the unwrapped results are sensitive to the number of multi-looks and that the Fisher Distance is the most suitable path-guiding index for our study. Two case studies are then designed to evaluate the feasibility of the proposed phase unwrapping method based on Cubature Kalman filtering. The results indicate that, compared with the popular Minimum Cost Flow method, the Cubature Kalman filtering-based phase unwrapping can achieve promising results without pre-filtering and is an appropriate method for coal mining areas with high noise. PMID:26153776

Exploring the effects of acid mine drainage on diatom teratology using geometric morphometry.

PubMed

Olenici, Adriana; Blanco, Saúl; Borrego-Ramos, María; Momeu, Laura; Baciu, Călin

2017-10-01

Metal pollution of aquatic habitats is a major and persistent environmental problem. Acid mine drainage (AMD) affects lotic systems in numerous and interactive ways. In the present work, a mining area (Roșia Montană) was chosen as study site, and we focused on two aims: (i) to find the set of environmental predictors leading to the appearance of the abnormal diatom individuals in the study area and (ii) to assess the relationship between the degree of valve outline deformation and AMD-derived pollution. In this context, morphological differences between populations of Achnanthidium minutissimum and A. macrocephalum, including normal and abnormal individuals, were evidenced by means of valve shape analysis. Geometric morphometry managed to capture and discriminate normal and abnormal individuals. Multivariate analyses (NMDS, PLS) separated the four populations of the two species mentioned and revealed the main physico-chemical parameters that influenced valve deformation in this context, namely conductivity, Zn, and Cu. ANOSIM test evidenced the presence of statistically significant differences between normal and abnormal individuals within both chosen Achnanthidium taxa. In order to determine the relative contribution of each of the measured physico-chemical parameters in the observed valve outline deformations, a PLS was conducted, confirming the results of the NMDS. The presence of deformed individuals in the study area can be attributed to the fact that the diatom communities were strongly affected by AMD released from old mining works and waste rock deposits.

Measuring mining safety with injury statistics: lost workdays as indicators of risk.

PubMed

Coleman, Patrick J; Kerkering, John C

2007-01-01

Mining in the United States remains one of the most hazardous industries, despite significant reductions in fatal injury rates over the last century. Coal mine fatality rates, for example, have dropped almost a thousand-fold since their peak in 1908. While incidence rates are very important indicators, lost worktime measures offer an alternative metric for evaluating job safety and health performance. The first objective of this study examined the distributions and summary statistics of all injuries reported to the Mine Safety and Health Administration from 1983 through 2004. Over the period studied (1983-2004), there were 31,515,368 lost workdays associated with mining injuries, for an equivalent of 5,700 person-years lost annually. The second objective addressed the problem of comparing safety program performance in mines for situations where denominator data were lacking. By examining the consequences of injuries, comparisons can be made between disparate operations without the need for denominators. Total risk in the form of lost workday sums can help to distinguish between lower- and higher-risk operations or time periods. Our method was to use a beta distribution to model the losses and to compare underground coal mining to underground metal/nonmetal mining from 2000 to 2004. Our results showed the probability of an injury having 10 or more lost workdays was 0.52 for coal mine cases versus 0.35 for metal/nonmetal mine cases. In addition, a comparison of injuries involving continuous mining machines over 2001-2002 versus 2003-2004 showed that the ratio of average losses in the later period to those in the earlier period was approximately 1.08, suggesting increasing risks for such operations. This denominator-free safety measure will help the mining industry more effectively identify higher-risk operations and more realistically evaluate their safety improvement programs. Attention to a variety of metrics concerning the performance of a job safety and health program will enhance industry's ability to manage these programs and reduce risk.

Mine fire experiments and simulation with MFIRE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laage, L.W.; Yang, Hang

1995-12-31

A major concern of mine fires is the heat generated ventilation disturbances which can move products of combustion (POC) through unexpected passageways. Fire emergency planning requires simulation of the interaction of the fire and ventilation system to predict the state of the ventilation system and the subsequent distribution of temperatures and POC. Several computer models were developed by the U.S. Bureau of Mines (USBM) to perform this simulation. The most recent, MFIRE, simulates a mine`s ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influencemore » such as varying outside temperatures, and internal influences such as fires. Extensive output allows quantitative analysis of the effects of the proposed alteration to die ventilation system. This paper describes recent USBM research to validate MFIRE`s calculation of temperature distribution in an airway due to a mine fire, as temperatures are the most significant source of ventilation disturbances. Fire tests were conducted at the Waldo Mine near Magdalena, NM. From these experiments, temperature profiles were developed as functions of time and distance from the fire and compared with simulations from MFIRE.« less

Influence of Organic Matter - Mineral Interfacial Reactions on Metal(loid) Speciation and Bioaccessibility

NASA Astrophysics Data System (ADS)

Chorover, J.; Kong, S.; Root, R. A.; Thomas, A.

2015-12-01

Bioaccessibility of contaminant metals in geomedia is often measured on the basis of kinetic release to solution during in vitro reaction with biofluid simulants. We postulate that development of a predictive-mechanistic understanding of bioaccessibility requires knowledge of metal(loid) molecular speciation upon sample introduction, as well as its change over the course of the in vitro reaction. Our results - including data from batch, column, mesocosm and field studies pertaining to arsenic, lead, and zinc contaminated materials - indicate the strong influence of organic matter and associated biological activity on metal(loid) speciation in mine tailings and related model systems. Furthermore, presence/absence of organic matter during bioassays affects the kinetics of metal(loid) release into biofluid simulants through multiple mechanisms.

30 CFR 817.45 - Hydrologic balance: Sediment control measures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Hydrologic balance: Sediment control measures. 817.45 Section 817.45 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT...-UNDERGROUND MINING ACTIVITIES § 817.45 Hydrologic balance: Sediment control measures. (a) Appropriate sediment...

30 CFR 816.45 - Hydrologic balance: Sediment control measures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Hydrologic balance: Sediment control measures. 816.45 Section 816.45 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT...-SURFACE MINING ACTIVITIES § 816.45 Hydrologic balance: Sediment control measures. (a) Appropriate sediment...

30 CFR 816.45 - Hydrologic balance: Sediment control measures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Hydrologic balance: Sediment control measures. 816.45 Section 816.45 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT...-SURFACE MINING ACTIVITIES § 816.45 Hydrologic balance: Sediment control measures. (a) Appropriate sediment...

30 CFR 817.45 - Hydrologic balance: Sediment control measures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Hydrologic balance: Sediment control measures. 817.45 Section 817.45 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT...-UNDERGROUND MINING ACTIVITIES § 817.45 Hydrologic balance: Sediment control measures. (a) Appropriate sediment...

Methodology of selecting dozers for lignite open pit mines in Serbia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stojanovic, D.; Ignjatovic, D.; Kovacevic, S.

1996-12-31

Apart from the main production processes (coal and overburden mining, rail conveyors transportation and storage of excavated masses) performed by great-capacity mechanization at open pit mines, numerous and different auxiliary works, that often have crucial influence on both the work efficiency of main equipment and the maintenance of optimum technical conditions of machines and plants covering technological system of open pit, are present. Successful realization of work indispensably requires a proper and adequate selection of auxiliary machines according to their type quantity, capacity, power etc. thus highly respecting specific conditions existing at each and every open pit mine. A dozermore » is certainly the most important and representative auxiliary machine at single open pit mine. It is widely used in numerous works that, in fact, are preconditions for successful work of the main mechanization and consequently the very selection of a dozer ranges among the most important operations when selecting mechanization. This paper presents the methodology of dozers selection when lignite open pit mines are concerned. A mathematical model defining the volume of work required for dozers to perform at open pit mines and consequently the number of necessary dozers was designed. The model underwent testing in practice at big open pit mines and can be used in design of future open pits mines.« less

Historical archaeology at the Clarkson Mine, an eastern Ohio mining complex

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keener, C.S.

2003-07-01

This study examines the Clarkson Mine (33BL333), an eastern Ohio coal mine complex dating to the 1910s to 1920s, situated along Wheeling Creek. The results of preliminary surveys and the subsequent mitigation of four structures at the site are presented. The historical archaeology conducted at the site demonstrates the significant research possibilities inherent at many of these early industrial mine complexes. Of particular interest is the findings of depositional patterning around residential structures that revealed the influence of architecture on where and how items were deposited on the land surface. The ceramic and faunal assemblage were analyzed and provide significantmore » details on socioeconomic attributes associated with the workers or staff. Artifacts recovered at the site provide an excellent diagnostic framework from which other similarly aged sites can be compared and dated. The findings at the Clarkson Mine are also placed into a more regional perspective and compared with other contemporary studies.« less

Local Community Perceptions of Mine Site Restoration Using Phytoremediation in Abitibi-Temiscamingue (Quebec).

PubMed

Vodouhe, Fifanou G; Khasa, Damase P

2015-01-01

This work explores factors supporting people perception about mine site restoration and phytoremediation. Phytoremediation is one of the most eco-friendly restoration strategy emerged since the last two decades but studies on local people perception on this restoration strategy are scarce. To fill in this gap, data were collected from mining stakeholders using a structured questionnaire administered through snowball sampling method. We used Multiple Correspondence Analysis as implemented in the software XLSTAT to visualize relationship between participants' characteristics, their view on mine site restoration and phytoremediation. Results clearly show out that people perception on mine site restoration is influenced by mining activities effects on health and region attractiveness. Phytoremediation (65.21%) was rated positively with regard to its environment potential, aesthetic and consideration for future generation followed by fillings and excavating. Restoration strategy costs have no effect on people choice and participants prefer use of shrubs as vegetation component of phytoremediation to reach their restoration objective.

A baseline record of trace elements concentration along the beach placer mining areas of Kanyakumari coast, South India.

PubMed

Simon Peter, T; Chandrasekar, N; John Wilson, J S; Selvakumar, S; Krishnakumar, S; Magesh, N S

2017-06-15

Trace element concentration in the beach placer mining areas of Kanyakumari coast, South India was assessed. Sewage and contaminated sediments from mining sites has contaminated the surface sediments. Enrichment factor indicates moderately severe enrichment for Pb, minor enrichment for Mn, Zn, Ni, Fe and no enrichment for Cr and Cu. The Igeo values show higher concentration of Pb ranging in the scale of 3-4, which shows strong contamination due to high anthropogenic activity such as mining and terrestrial influences into the coastal regions. Correlation coefficient shows that most of the elements are associated with each other except Ni and Pb. Factor analysis reveals that Mn, Zn, Fe, Cr, Pb and Cu are having a significant loading and it indicates that these elements are mainly derived from similar origin. The cluster analysis clearly indicated that the mining areas are grouped under cluster 2 and non-mining areas are clustered under group 1. Copyright © 2017 Elsevier Ltd. All rights reserved.

Evaluation of Streamflow Gain-Loss Characteristics of Hubbard Creek, in the Vicinity of a Mine-Permit Area, Delta County, Colorado, 2007

USGS Publications Warehouse

Ruddy, Barbara C.; Williams, Cory A.

2007-01-01

In 2007, the U.S. Geological Survey, in cooperation with Bowie Mining Company, initiated a study to characterize the streamflow and streamflow gain-loss in a reach of Hubbard Creek in Delta County, Colorado, in the vicinity of a mine-permit area planned for future coal mining. Premining streamflow characteristics and streamflow gain-loss variation were determined so that pre- and postmining gain-loss characteristics could be compared. This report describes the methods used in this study and the results of two streamflow-measurement sets collected during low-flow conditions. Streamflow gain-loss measurements were collected using rhodamine WT and sodium bromide tracers at four sites spanning the mine-permit area on June 26-28, 2007. Streamflows were estimated and compared between four measurement sites within three stream subreaches of the study reach. Data from two streamflow-gaging stations on Hubbard Creek upstream and downstream from the mine-permit area were evaluated. Streamflows at the stations were continuous, and flow at the upstream station nearly always exceeded the streamflow at the downstream station. Furthermore, streamflow at both stations showed similar diurnal patterns with traveltime offsets. On June 26, streamflow from the gain-loss measurements was greater at site 1 (most upstream site) than at site 4 (most downstream site); on June 27, streamflow was greater at site 4 than at site 2; and on June 27, there was no difference in streamflow between sites 2 and 3. Data from streamflow-gaging stations 09132940 and 09132960 showed diurnal variations and overall decreasing streamflow over time. The data indicate a dynamic system, and streamflow can increase or decrease depending on hydrologic conditions. The streamflow within the study reach was greater than the streamflows at either the upstream or downstream stations. A second set of gain-loss measurements was collected at sites 2 and 4 on November 8-9, 2007. On November 8, streamflow was greater at site 4 than at site 2, and on the following day, November 9, streamflow was greater at site 2 than at site 4. Data collection on November 8 occurred while the streamflow was increasing due to contributions from stream ice melting throughout different parts of the basin. Data collection on November 9 occurred earlier in the day with less stream ice melting and more steady-state conditions, so the indication that streamflow decreased between sites 2 and 4 may be more accurate. Diurnal variations in streamflow are common at both the upper and the lower streamflow-gaging stations. The upper streamflow-gaging station shows a melt-freeze influence from tributaries to Hubbard Creek during the winter season. Downstream from the study reach, observed diurnal variation is likely due to evapotranspiration associated with dense flood-plain vegetation, which consumes water from the creek during the middle of the day. Varying diurnal patterns in streamflow, combined with possible variations in tributary inflows to Hubbard Creek in the study reach, probably account for the observed variations in streamflow at the tracer measurement sites. During both sampling periods in June and November 2007, conditions were less than ideal and not steady state. The June 27 sampling indicates that the streamflow was increasing between measurement sites 2 and 4, and the November 9 sampling indicates that the streamflow was decreasing between measurement sites 2 and 4. The data collected during the diurnal and day-to-day variations in streamflow indicated that the streamflow reach is dynamic and can be gaining, losing, or constant.

Method of locating underground mines fires

DOEpatents

Laage, Linneas; Pomroy, William

1992-01-01

An improved method of locating an underground mine fire by comparing the pattern of measured combustion product arrival times at detector locations with a real time computer-generated array of simulated patterns. A number of electronic fire detection devices are linked thru telemetry to a control station on the surface. The mine's ventilation is modeled on a digital computer using network analysis software. The time reguired to locate a fire consists of the time required to model the mines' ventilation, generate the arrival time array, scan the array, and to match measured arrival time patterns to the simulated patterns.

The influence of drilling process automation on improvement of blasting works quality in open pit mining

NASA Astrophysics Data System (ADS)

Bodlak, Maciej; Dmytryk, Dominik; Mertuszka, Piotr; Szumny, Marcin; Tomkiewicz, Grzegorz

2018-01-01

The article describes the monitoring system of blasthole drilling process called HNS (Hole Navigation System), which was used in blasting works performed by Maxam Poland Ltd. Developed by Atlas Copco's, the HNS system - using satellite data - allows for a very accurate mapping of the designed grid of blastholes. The article presents the results of several conducted measurements of ground vibrations triggered by blasting, designed and performed using traditional technology and using the HNS system and shows first observations in this matter.

Hydrologic data collected in the vicinity of the proposed gamma-ray and neutrino detector site, Hot Spring County, Arkansas, 1988-89

USGS Publications Warehouse

Fitzpatrick, D.J.; Westerfield, P.W.

1990-01-01

An abandoned barite mine in Hot Spring County, Arkansas, has been selected as the location for a proposed gamma-ray and neutrino detector site. As part of the hydrologic evaluation of the site, the U.S. Geological Survey in cooperation with the Arkansas Geological Commission collected hydrologic data at selected locations in the vicinity of the abandoned barite mine. Data collected as part of the project included water quality, pond-evaluation, and precipitation data within the abandoned barite mine and flow and water quality data at selected sites in the vicinity of the mine. Water quality samples from within the abandoned mine were collected at three locations in the pond at selected depths. These data included field measurements of specific conductance, pH, water temperature, dissolved oxygen, major ions, and trace metals. Major ion and trace-metal samples were collected at six stream sites, one lake site, and two wastewater pond sites. Pond elevation and precipitation data from within the abandoned barite mine were measured during the period between July 1, 1988 and June 30, 1989. Twevle discharge measurements during the period between June 21, 1988, and June 26, 1989, were collected at six sites in the vicinity of the abandoned barite mine. (USGS)

Anomalous abundance and redistribution patterns of rare earth elements in soils of a mining area in Inner Mongolia, China.

PubMed

Wang, Lingqing; Liang, Tao

2016-06-01

The Bayan Obo Mine, the largest rare earth element (REE) deposit ever found in the world, has been mined for nearly 60 years for iron and rare earth elements. To assess the influences of mining activities on geochemical behavior of REEs in soils, 27 surface soil samples and three soil profile samples were collected from different directions in the vicinity of the mine area. The total concentrations of REEs in surface soils varied from 149.75 to 18,891.81 mg kg(-1) with an average value of 1906.12 mg kg(-1), which was apparently higher than the average values in China (181 mg kg(-1)). The order of the average concentrations of individual REEs in surface soils was similar to that in Bayan Obo ores, which confirmed that the concentration and distribution of REEs in the soils was influenced by the mining activities. The concentrations of single REE in the soil profiles showed a similar trend with depth with an increase at 0-25 cm section, then decreased and remained relatively stable in the deep part. The normalized curves inclined to the right side, showing the conspicuous fractionation between the light and heavy REEs, which supported by the North American Shale Composite (NASC) and Post-Archean Australian Shale (PAAS) normalized concentration ratios calculated for selected elements (La N /Yb N , La N /Sm N , Gd N /Yb N ). Slight positive Ce anomaly and negative Eu anomaly were also observed.

Application of Tracer-Injection Techniques to Demonstrate Surface-Water and Ground-Water Interactions Between an Alpine Stream and the North Star Mine, Upper Animas River Watershed, Southwestern Colorado

USGS Publications Warehouse

Wright, Winfield G.; Moore, Bryan

2003-01-01

Tracer-injection studies were done in Belcher Gulch in the upper Animas River watershed, southwestern Colorado, to determine whether the alpine stream infiltrates into underground mine workings of the North Star Mine and other nearby mines in the area. The tracer-injection studies were designed to determine if and where along Belcher Gulch the stream infiltrates into the mine. Four separate tracer-injec-tion tests were done using lithium bromide (LiBr), optical brightener dye, and sodium chloride (NaCl) as tracer solu-tions. Two of the tracers (LiBr and dye) were injected con-tinuously for 24 hours, one of the NaCl tracers was injected continuously for 12 hours, and one of the NaCl tracers was injected over a period of 1 hour. Concentration increases of tracer constituents were detected in water discharging from the North Star Mine, substantiating a surface-water and ground-water connection between Belcher Gulch and the North Star Mine. Different timing and magnitude of tracer breakthroughs indicated multiple flow paths with different residence times from the stream to the mine. The Pittsburgh and Sultan Mines were thought to physically connect to the North Star Mine, but tracer breakthroughs were inconclusive in water from these mines. From the tracer-injection tests and synoptic measure-ments of streamflow discharge, a conceptual model was devel-oped for surface-water and ground-water interactions between Belcher Gulch and the North Star Mine. This information, combined with previous surface geophysical surveys indicat-ing the presence of subsurface voids, may assist with decision-making process for preventing infiltration and for the remedia-tion of mine drainage from these mines.

Applied Geochemistry Special Issue on Environmental geochemistry of modern mining

USGS Publications Warehouse

Seal, Robert R.; Nordstrom, D. Kirk

2015-01-01

Environmental geochemistry is an integral part of the mine-life cycle, particularly for modern mining. The critical importance of environmental geochemistry begins with pre-mining baseline characterization and the assessment of environmental risks related to mining, continues through active mining especially in water and waste management practices, and culminates in mine closure. The enhanced significance of environmental geochemistry to modern mining has arisen from an increased knowledge of the impacts that historical and active mining can have on the environment, and from new regulations meant to guard against these impacts. New regulations are commonly motivated by advances in the scientific understanding of the environmental impacts of past mining. The impacts can be physical, chemical, and biological in nature. The physical challenges typically fall within the purview of engineers, whereas the chemical and biological challenges typically require a multidisciplinary array of expertise including geologists, geochemists, hydrologists, microbiologists, and biologists. The modern mine-permitting process throughout most of the world now requires that potential risks be assessed prior to the start of mining. The strategies for this risk assessment include a thorough characterization of pre-mining baseline conditions and the identification of risks specifically related to the manner in which the ore will be mined and processed, how water and waste products will be managed, and what the final configuration of the post-mining landscape will be.In the Fall 2010, the Society of Economic Geologists held a short course in conjunction with the annual meeting of the Geological Society of America in Denver, Colorado (USA) to examine the environmental geochemistry of modern mining. The intent was to focus on issues that are pertinent to current and future mines, as opposed to abandoned mines, which have been the focus of numerous previous short courses. The geochemical challenges of current and future mines share similarities with abandoned mines, but differences also exist. Mining and ore processing techniques have changed; the environmental footprint of waste materials has changed; environmental protection has become a more integral part of the mine planning process; and most historical mining was done with limited regard for the environment. The 17 papers in this special issue evolved from the Society of Economic Geologists’ short course.The relevant geochemical processes encompass the source, transport, and fate of contaminants related to the life cycle of a mine. Contaminants include metals and other inorganic species derived from geologic sources such as ore and solid mine waste, and substances brought to the site for ore processing, such as cyanide to leach gold. Factors, such as mine-waste mineralogy, hydrologic setting, mine-drainage chemistry, and microbial activity, that affect the hydrochemical risks from mining are reviewed by Nordstrom et al. In another paper, Nordstrom discusses baseline characterization at mine sites in a regulatory framework, and emphasizes the influence of mineral deposits in producing naturally elevated concentrations of many trace elements in surface water and groundwater. Surface water quality in mineralized watersheds is influenced by a number of processes that act on daily (diel) cycles and can produce dramatic variations in trace element concentrations as described by Gammons et al. Pre-mining baseline characterization studies should strive to capture the magnitude of these diel variations. Desbarats et al., using a case study of mine drainage from a gold mine, illustrate how elements that commonly occur as negatively charged species (anions) in solution, such as arsenic as arsenate, behave in an opposite fashion than most metals, which occur as positively charged species (cations). Significant improvement in the understanding of factors that influence the toxicity of metals to aquatic organisms in surface water has highlighted the importance of aqueous chemistry, particularly dissolved organic carbon, as described by Smith et al. Stream sediment contamination is another important pathway for affecting aquatic organisms, as reviewed by Besser et al. Understanding and predicting environmental consequences from mining begins with knowing the mineralogy and mineral reactivity of the ore, the wastes, and of secondary minerals formed later. Jamieson et al. review the importance of mineralogical studies in mine planning and remediation. A number of types of site-specific studies are needed to identify environmental risks related to individual mines. Lapakko reviews the general framework of mine waste characterization studies that are integral to the mine planning process. Hageman et al. present a comparative study of several static tests commonly used to characterize mine waste.The mining and ore processing practices employed at a specific mine site will vary on the basis of the commodities being targeted, the geology of the deposit, the geometry of the deposit, and the mining and ore processing methods used. Thus, these factors, in addition to the waste management practices used, can result in a variety of end-member mine waste features, each of which has its own set of challenges. Open pit mines and underground mines require waste rock to be removed to access ore. Waste rock presents unique problems because the rock is commonly mineralized at sub-economic grades and has not been processed to remove potentially problematic minerals, such as pyrite. Amos et al. examine the salient aspects of the geochemistry of waste rock. Mill tailings – the waste material after ore minerals have been removed – are a volumetrically important solid waste at many mine sites. Their fine grain size and the options for their management make their behavior in the environment distinct from that of waste rock. Lindsay et al. describe some of these differences through three case-study examples. Subaqueous disposal of tailings is another option described by Moncur et al. Cyanide leaching for gold extraction is a common method throughout the world. Johnson describes environmental aspects of cyanidation. Uranium mining presents unique environmental challenges, particularly since in-situ recovery has seen widespread use. Campbell et al. review the environmental geochemistry of uranium mining and current research on bioremediation. Ore concentrates from many types of metal mining undergo a pyrometallurgical technique known as smelting to extract the metal. Slag is the result of smelting, and it may be an environmental liability or a valuable byproduct, as described by Piatak et al. Finally, the open pits that result from surface mining commonly reach below the water table. At the end of mining, these pits may fill to form lakes that become part of the legacy of the mine. Castendyk et al., in two papers, review theoretical aspects of the environmental limnology of pit lakes. They also describe approaches that have been used to model pit lake water balance, wall-rock contributions to pit lake chemistry, pit lake water quality, and limnological processes, such as vertical mixing, through the use of three case studies.

Design concerns of room and pillar retreat panels

PubMed Central

Klemetti, Ted M.; Sears, Morgan M.; Tulu, Ihsan B.

2017-01-01

Why do some room and pillar retreat panels encounter abnormal conditions? What factors deserve the most consideration during the planning and execution phases of mining and what can be done to mitigate those abnormal conditions when they are encountered? To help answer these questions, and to determine some of the relevant factors influencing the conditions of room and pillar (R & P) retreat mining entries, four consecutive R & P retreat panels were evaluated. This evaluation was intended to reinforce the influence of topographic changes, depth of cover, multiple-seam interactions, geological conditions, and mining geometry. This paper details observations were made in four consecutive R & P retreat panels and the data were collected from an instrumentation site during retreat mining. The primary focus was on the differences observed among the four panels and within the panels themselves. The instrumentation study was initially planned to evaluate the interactions between primary and secondary support, but produced rather interesting results relating to the loading encountered under the current mining conditions. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the stress conditions. Both the LaModel 3.0 and Rocscience Phase 2 programs were used to evaluate these four panels. The results of both models indicated a drastic reduction in the vertical stresses experienced in these panels due to the full extraction mining in overlying seams when compared to the full overburden load. Both models showed a higher level of stress associated with the outside entries of the panels. These results agree quite well with the observations and instrumentation studies performed at the mine. These efforts provided two overarching conclusions concerning R & P retreat mine planning and execution. The first was that there are four areas that should not be overlooked during R & P retreat mining: topographic relief, multiple-seam stress relief, stress concentrations near the gob edge, and geologic changes in the immediate roof. The second is that in order to successfully retreat an R & P panel, a three-phased approach to the design and analysis of the panel should be conducted: the planning phase, evaluation phase, and monitoring phase. PMID:28626598

Invited Article: In situ comparison of passive radon-thoron discriminative monitors at subsurface workplaces in Hungary

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kávási, Norbert, E-mail: norbert@fml.nirs.go.jp; Social Organization for Radioecological Cleanliness, Veszprém; Vigh, Tamás

During a one-year long measurement period, radon and thoron data obtained by two different passive radon-thoron discriminative monitors were compared at subsurface workplaces in Hungary, such as mines (bauxite and manganese ore) and caves (medical and touristic). These workplaces have special environmental conditions, such as, stable and high relative humidity (100%), relatively stable temperature (12°C–21°C), low or high wind speed (max. 2.4 m s{sup −1}) and low or elevated aerosol concentration (130–60 000 particles m{sup −3}). The measured radon and thoron concentrations fluctuated in a wide range among the different workplaces. The respective annual average radon concentrations and their standard deviations (inmore » brackets) measured by the passive radon-thoron discriminative monitor with cellulose filter (CF) and the passive radon-thoron discriminative monitor with sponge filter (SF) were: 350(321) Bq m{sup −3} and 550(497) Bq m{sup −3} in the bauxite mine; 887(604) Bq m{sup −3} and 1258(788) Bq m{sup −3} in the manganese ore mine; 2510(2341) Bq m{sup −3} and 3403(3075) Bq m{sup −3} in the medical cave (Hospital Cave of Tapolca); and 6239(2057) Bq m{sup −3} and 8512(1955) Bq m{sup −3} in the touristic cave (Lake Cave of Tapolca). The respective average thoron concentrations and their standard deviation (in brackets) measured by CF and SF monitors were: 154(210) Bq m{sup −3} and 161(148) Bq m{sup −3} in the bauxite mine; 187(191) Bq m{sup −3} and 117(147) Bq m{sup −3} in the manganese-ore mine; 360(524) Bq m{sup −3} and 371(789) Bq m{sup −3} in the medical cave (Hospital Cave of Tapolca); and 1420(1184) Bq m{sup −3} and 1462(3655) Bq m{sup −3} in the touristic cave (Lake Cave of Tapolca). Under these circumstances, comparison of the radon data for the SF and CF monitors showed the former were consistently 51% higher in the bauxite mine, 38% higher in the manganese ore mine, and 34% higher in the caves. Consequently, correction is required on previously obtained radon data acquired by CF monitors at subsurface workplaces to gain comparable data for SF monitors. In the case of thoron, the data were unreliable and no significant tendency was seen during the comparison therefore comparison of previously obtained thoron data acquired by either CF or SF is doubtful. There was probable influence by relative humidity on the detection response; however, the effects of the high wind speed and elevated aerosol concentration could not be excluded. The results of this study call attention to the importance of calibration under extreme environmental conditions and the need for using reliable radon-thoron monitors for subsurface workplaces.« less

Optimization research of structural parameters in non-pillar sublevel caving method with large structural parameters

NASA Astrophysics Data System (ADS)

Han, Wencheng; Zhou, Renjie; Liu, Xianfeng; Sun, Dongdong

2018-03-01

The non-pillar sublevel caving method with large structural parameters used in Mao Gong Iron Mine is of high rate of dilution and loss, and the ore recovery rate is less than 50%. Aiming at this problem, this paper analyzes the influence mechanism of the caving step on the mining index by means of the matching relationship between the shape of caved ore body and the drawn-out ore body, then through the physical simulation experiment in laboratory, the mining index such as the volume of pure ore drawing, ore recovery ratio and rock mixing ratio are studied under different caving step. The results show that the mining index under caving step of two row of blast hole is better than that under caving step of one row of blast hole. The research has guided significance for production of the mine.

The influence of para-seismic vibrations, induced by blasting works, on structures: a Case Study

NASA Astrophysics Data System (ADS)

Andrusikiewicz, Wacław

2018-04-01

Underground mining operations are often associated with the necessity to use explosives. Several hundreds of kilograms of explosives, subdivided into small charges suitable for a specific mining job, are used each time in a blasting operation. In many cases, mining engineers carry out remote central blasting works, which means that all the charges placed at faces are initiated from one control point (usually, a control room in the mine) at the same time. Such coordinated explosions generate para-seismic movements whose consequences can be felt on land surface, with subsequent effects identified in buildings and structures. This paper discusses briefly selected standards applicable to the harmful para-seismic impacts. The author presents the results of the research conducted with the intention to identify harmful effects of the basting works carried out in the "Kłodawa" Salt Mine.

Native mycorrhizal fungi replace introduced fungal species on Virginia pine and American chestnut planted on reclaimed mine sites of Ohio

Treesearch

Shivanand Hiremath; Kirsten Lehtoma; Jenise M. Bauman

2014-01-01

Plant-microbe community dynamics influence the natural succession of plant species where pioneer vegetation facilitates the establishment of a distantly related, later successional plant species. This has been observed in the case of restoration of the American chestnut (Castanea dentata) on abandoned mine land where Virginia pine (Pinus...

Models for electromagnetic coupling of lightning onto multiconductor cables in underground cavities

NASA Astrophysics Data System (ADS)

Higgins, Matthew Benjamin

This dissertation documents the measurements, analytical modeling, and numerical modeling of electromagnetic transfer functions to quantify the ability of cloud-to-ground lightning strokes (including horizontal arc-channel components) to couple electromagnetic energy onto multiconductor cables in an underground cavity. Measurements were performed at the Sago coal mine located near Buckhannon, WV. These transfer functions, coupled with mathematical representations of lightning strokes, are then used to predict electric fields within the mine and induced voltages on a cable that was left abandoned in the sealed area of the Sago mine. If voltages reached high enough levels, electrical arcing could have occurred from the abandoned cable. Electrical arcing is known to be an effective ignition source for explosive gas mixtures. Two coupling mechanisms were measured: direct and indirect drive. Direct coupling results from the injection or induction of lightning current onto metallic conductors such as the conveyors, rails, trolley communications cable, and AC power shields that connect from the outside of the mine to locations deep within the mine. Indirect coupling results from electromagnetic field propagation through the earth as a result of a cloud-to-ground lightning stroke or a long, low-altitude horizontal current channel from a cloud-to-ground stroke. Unlike direct coupling, indirect coupling does not require metallic conductors in a continuous path from the surface to areas internal to the mine. Results from the indirect coupling measurements and analysis are of great concern. The field measurements, modeling, and analysis indicate that significant energy can be coupled directly into the sealed area of the mine. Due to the relatively low frequency content of lightning (< 100 kHz), electromagnetic energy can readily propagate through hundreds of feet of earth. Indirect transfer function measurements compare extremely well with analytical and computational models developed for the Sago site which take into account measured soil properties.

Application of MIKE SHE to study the impact of coal mining on river runoff in Gujiao mining area, Shanxi, China

PubMed Central

Ping, Jianhua; Yan, Shiyan; Gu, Pan; Wu, Zening; Hu, Caihong

2017-01-01

Coal mining is one of the core industries that contribute to the economic development of a country but deteriorate the environment. Being the primary source of energy, coal has become essential to meet the energy demand of a country. It is excavated by both opencast and underground mining methods and affects the environment, especially hydrological cycle, by discharging huge amounts of mine water. Natural hydrological processes have been well known to be vulnerable to human activities, especially large scale mining activities, which inevitably generate surface cracks and subsidence. It is therefore valuable to assess the impact of mining on river runoff for the sustainable development of regional economy. In this paper, the impact of coal mining on river runoff is assessed in one of the national key coal mining sites, Gujiao mining area, Shanxi Province, China. The characteristics of water cycle are described, the similarities and differences of runoff formation are analyzed in both coal mining and pre-mining periods. The integrated distributed hydrological model named MIKE SHE is employed to simulate and evaluate the influence of coal mining on river runoff. The study shows that mining one ton of raw coal leads to the reduction of river runoff by 2.87 m3 between 1981 and 2008, of which the surface runoff decreases by 0.24 m3 and the baseflow by 2.63 m3. The reduction degree of river runoff for mining one ton of raw coal shows an increasing trend over years. The current study also reveals that large scale coal mining initiates the formation of surface cracks and subsidence, which intercepts overland flow and enhances precipitation infiltration. Together with mine drainage, the natural hydrological processes and the stream flows have been altered and the river run off has been greatly reduced. PMID:29267313

Application of MIKE SHE to study the impact of coal mining on river runoff in Gujiao mining area, Shanxi, China.

PubMed

Ping, Jianhua; Yan, Shiyan; Gu, Pan; Wu, Zening; Hu, Caihong

2017-01-01

Coal mining is one of the core industries that contribute to the economic development of a country but deteriorate the environment. Being the primary source of energy, coal has become essential to meet the energy demand of a country. It is excavated by both opencast and underground mining methods and affects the environment, especially hydrological cycle, by discharging huge amounts of mine water. Natural hydrological processes have been well known to be vulnerable to human activities, especially large scale mining activities, which inevitably generate surface cracks and subsidence. It is therefore valuable to assess the impact of mining on river runoff for the sustainable development of regional economy. In this paper, the impact of coal mining on river runoff is assessed in one of the national key coal mining sites, Gujiao mining area, Shanxi Province, China. The characteristics of water cycle are described, the similarities and differences of runoff formation are analyzed in both coal mining and pre-mining periods. The integrated distributed hydrological model named MIKE SHE is employed to simulate and evaluate the influence of coal mining on river runoff. The study shows that mining one ton of raw coal leads to the reduction of river runoff by 2.87 m3 between 1981 and 2008, of which the surface runoff decreases by 0.24 m3 and the baseflow by 2.63 m3. The reduction degree of river runoff for mining one ton of raw coal shows an increasing trend over years. The current study also reveals that large scale coal mining initiates the formation of surface cracks and subsidence, which intercepts overland flow and enhances precipitation infiltration. Together with mine drainage, the natural hydrological processes and the stream flows have been altered and the river run off has been greatly reduced.

Optimization of Plant Growth-Promoting Bacteria-Assisted Phytostabilization of Mine Tailings

PubMed Central

Grandlic, Christopher J.; Palmer, Michael W.; Maier, Raina M.

2009-01-01

Recent studies have indicated that plant growth-promoting bacteria (PGPB) can improve revegetation of arid mine tailings as measured by increased biomass production. The goals of the present study were first to evaluate how mode of application of known PGPB affects plant growth, and second to evaluate the effect of this inoculation on rhizosphere microbial community structure. PGPB application strategies investigated include preliminary surface sterilization of seeds (a common practice in phytoremediation trials) followed by a comparison of two application methods; immersion and alginate encapsulation. Results with two native desert plant species, Atriplex lentiformis and Buchloe dactyloides, suggest that seed surface sterilization prior to inoculation is not necessary to achieve beneficial effects of introduced PGPB. Both PGPB application techniques generally enhanced plant growth although results were both plant and PGPB specific. These results demonstrate that alginate encapsulation, which allows for long-term storage and easier application to seeds, is an effective way to inoculate PGPB. In addition, the influence of PGPB application on B. dactyloides rhizosphere community structure was evaluated using PCR-DGGE (denaturing gradient gel electrophoresis) analysis of bacterial DNA extracted from rhizosphere samples collected 75 d following planting. A comparative analysis of DGGE profiles was performed using canonical correspondence analysis (CCA). DGGE-CCA showed that rhizosphere community profiles from PGPB-inoculated treatments are significantly different from both uninoculated tailings rhizosphere profiles and profiles from the compost used to amend the tailings. Further, community profiles from B. dactyloides inoculated with the best performing PGPB (Arthro mix) were significantly different from two other PGPB tested. These results suggest that introduced PGPB have the potential to influence the development of the rhizosphere community structure found in plants grown in mine tailings. PMID:20161141

Modeling and Analysis of Integrated Bathymetric and Geodetic Data for Inventory Surveys of Mining Water Reservoirs

NASA Astrophysics Data System (ADS)

Ochałek, Agnieszka; Lipecki, Tomasz; Jaśkowski, Wojciech; Jabłoński, Mateusz

2018-03-01

The significant part of the hydrography is bathymetry, which is the empirical part of it. Bathymetry is the study of underwater depth of waterways and reservoirs, and graphic presentation of measured data in form of bathymetric maps, cross-sections and three-dimensional bottom models. The bathymetric measurements are based on using Global Positioning System and devices for hydrographic measurements - an echo sounder and a side sonar scanner. In this research authors focused on introducing the case of obtaining and processing the bathymetrical data, building numerical bottom models of two post-mining reclaimed water reservoirs: Dwudniaki Lake in Wierzchosławice and flooded quarry in Zabierzów. The report includes also analysing data from still operating mining water reservoirs located in Poland to depict how bathymetry can be used in mining industry. The significant issue is an integration of bathymetrical data and geodetic data from tachymetry, terrestrial laser scanning measurements.

Earth Conductivity Estimation from Through-the-Earth Measurements of 94 Coal Mines Using Different Electromagnetic Models

PubMed Central

Yan, Lincan; Waynert, Joseph; Sunderman, Carl

2015-01-01

Through-the-Earth (TTE) communication systems require minimal infrastructure to operate. Hence, they are assumed to be more survivable and more conventional than other underground mine communications systems. This survivability is a major advantage for TTE systems. In 2006, Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which requires all underground coal mines to install wireless communications systems. The intent behind this mandate is for trapped miners to be able to communicate with surface personnel after a major accident-hence, the interest in TTE communications. To determine the likelihood of establishing a TTE communication link, it would be ideal to be able to predict the apparent conductivity of the overburden above underground mines. In this paper, all 94 mine TTE measurement data collected by Bureau of Mines in the 1970s and early 1980s, are analyzed for the first time to determine the apparent conductivity of the overburden based on three different models: a homogenous half-space model, a thin sheet model, and an attenuation factor or Q-factor model. A statistical formula is proposed to estimate the apparent earth conductivity for a specific mine based on the TTE modeling results given the mine depth and signal frequency. PMID:26213457

Earth Conductivity Estimation from Through-the-Earth Measurements of 94 Coal Mines Using Different Electromagnetic Models.

PubMed

Yan, Lincan; Waynert, Joseph; Sunderman, Carl

2014-10-01

Through-the-Earth (TTE) communication systems require minimal infrastructure to operate. Hence, they are assumed to be more survivable and more conventional than other underground mine communications systems. This survivability is a major advantage for TTE systems. In 2006, Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which requires all underground coal mines to install wireless communications systems. The intent behind this mandate is for trapped miners to be able to communicate with surface personnel after a major accident-hence, the interest in TTE communications. To determine the likelihood of establishing a TTE communication link, it would be ideal to be able to predict the apparent conductivity of the overburden above underground mines. In this paper, all 94 mine TTE measurement data collected by Bureau of Mines in the 1970s and early 1980s, are analyzed for the first time to determine the apparent conductivity of the overburden based on three different models: a homogenous half-space model, a thin sheet model, and an attenuation factor or Q-factor model. A statistical formula is proposed to estimate the apparent earth conductivity for a specific mine based on the TTE modeling results given the mine depth and signal frequency.

Mercury methylation in mine wastes collected from abandoned mercury mines in the USA

USGS Publications Warehouse

Gray, J.E.; Hines, M.E.; Biester, H.; Lasorsa, B.K.; ,

2003-01-01

Speciation and transformation of Hg was studied in mine wastes collected from abandoned Hg mines at McDermitt, Nevada, and Terlingua, Texas, to evaluate formation of methyl-Hg, which is highly toxic. In these mine wastes, we measured total Hg and methyl-Hg contents, identified various Hg compounds using a pyrolysis technique, and determined rates of Hg methylation and methyl-Hg demethylation using isotopic-tracer methods. Mine wastes contain total Hg contents as high as 14000 ??g/g and methyl-Hg concentrations as high as 88 ng/g. Mine wastes were found to contain variable amounts of cinnabar, metacinnabar, Hg salts, Hg0, and Hg0 and Hg2+ sorbed onto matrix particulates. Samples with Hg0 and matrix-sorbed Hg generally contained significant methyl-Hg contents. Similarly, samples containing Hg0 compounds generally produced significant Hg methylation rates, as much as 26%/day. Samples containing mostly cinnabar showed little or no Hg methylation. Mine wastes with high methyl-Hg contents generally showed low methyl-Hg demethylation, suggesting that Hg methylation was dominant. Methyl-Hg demethylation was by both oxidative and microbial pathways. The correspondence of mine wastes containing Hg0 compounds and measured Hg methylation suggests that Hg0 oxidizes to Hg2+, which is subsequently bioavailable for microbial Hg methylation.

Measurement methods of building structures deflections

NASA Astrophysics Data System (ADS)

Wróblewska, Magdalena

2018-04-01

Underground mining exploitation is leading to the occurrence of deformations manifested by, in particular, sloping terrain. The structures situated on the deforming subsoil are subject to uneven subsidence which is leading in consequence to their deflection. Before a building rectification process takes place by, e.g. uneven raising, the structure's deflection direction and value is determined so that the structure is restored to its vertical position as a result of the undertaken remedial measures. Deflection can be determined by applying classical as well as modern measurement techniques. The article presents examples of measurement methods used considering the measured elements of building structures' constructions and field measurements. Moreover, for a given example of a mining area, the existing deflections of buildings were compared with mining terrain sloping.

The application of LANDSAT-1 imagery for monitoring strip mines in the new river watershed in northeast Tennessee, part 2

NASA Technical Reports Server (NTRS)

Shahrokhi, F. (Principal Investigator); Sharber, L. A.

1977-01-01

The author has identified the following significant results. LANDSAT imagery and supplementary aircraft photography of the New River drainage basin were subjected to a multilevel analysis using conventional photointerpretation methods, densitometric techniques, multispectral analysis, and statistical tests to determine the accuracy of LANDSAT-1 imagery for measuring strip mines of common size. The LANDSAT areas were compared with low altitude measurements. The average accuracy over all the mined land sample areas mapped from LANDSAT-1 was 90%. The discrimination of strip mine subcategories is somewhat limited on LANDSAT imagery. A mine site, whether active or inactive, can be inferred by lack of vegetation, by shape, or image texture. Mine ponds are difficult or impossible to detect because of their small size and turbidity. Unless bordered and contrasted with vegetation, haulage roads are impossible to delineate. Preparation plants and refuge areas are not detectable. Density slicing of LANDSAT band 7 proved most useful in the detection of reclamation progress within the mined areas. For most state requirements for year-round monitoring of surface mined land, LANDSAT is of limited value. However, for periodic updating of regional surface maps, LANDSAT may provide sufficient accuracies for some users.

The Use of Field and Mesocosm Experiments to Quantify Effects of Physical and Chemical Stressors in Mining-Contaminated Streams.

PubMed

Cadmus, Pete; Clements, William H; Williamson, Jacob L; Ranville, James F; Meyer, Joseph S; Gutiérrez Ginés, María Jesús

2016-07-19

Identifying causal relationships between acid mine drainage (AMD) and ecological responses in the field is challenging. In addition to the direct toxicological effects of elevated metals and reduced pH, mining activities influence aquatic organisms indirectly through physical alterations of habitat. The primary goal of this research was to quantify the relative importance of physical (metal-oxide deposition) and chemical (elevated metal concentrations) stressors on benthic macroinvertebrate communities. Mesocosm experiments conducted with natural assemblages of benthic macroinvertebrates established concentration-response relationships between metals and community structure. Field experiments quantified effects of metal-oxide contaminated substrate and showed significant differences in sensitivity among taxa. To predict the recovery of dominant taxa in the field, we integrated our measures of metal tolerance and substrate tolerance with estimates of drift propensity obtained from the literature. Our estimates of recovery were consistent with patterns observed at downstream recovery sites in the NFCC, which were dominated by caddisflies and baetid mayflies. We conclude that mesocosm and small-scale field experiments, particularly those conducted with natural communities, provide an ecologically realistic complement to laboratory toxicity tests. These experiments also control for the confounding variables associated with field-based approaches, thereby supporting causal relationships between AMD stressors and responses.

The Impact of the Rock Mass Deformation on Geometric Changes of a Historical Chimney in the Salt Mine of Bochnia

NASA Astrophysics Data System (ADS)

Szafarczyk, Anna; Gawałkiewicz, Rafał

2018-03-01

There are many ways of the geometry measurement of slim objects, with the application of geodetic and photogrammetric methods. A modern solution in the diagnostics of slim objects is the application of laser scanning, with the use of a scanner of a scanning total station. The point cloud, obtained from the surface of the scanned object gives the possibility of generating not only information on structural surface deformations, but also facilitates obtaining the data on the geometry of the axis of the building, as a basic indicator of the characteristics of its deformation. The cause of the change in the geometry of slim objects is the impact of many external and internal factors. These objects are located in the areas of working or closed underground mines. They can be impacted by the ground and they can face the results of the convergence of cavities. A specific structure of the salt rock mass causes subsequent convergence of the post-exploitation cavities, which has the influence on the behaviour of the terrain surface and the related objects. The authors analysed the impact of the changes in the rock mass and the surface on the changes of the industrial chimney in the Bochnia Salt Mine.

Spatial Modeling of the Influence of Mining-Geometric Indices on the Efficiency of Mining

NASA Astrophysics Data System (ADS)

Sobolevskyi, Ruslan; Korobiichuk, Igor; Nowicki, Michał; Szewczyk, Roman; Shlapak, Vladimir

2017-12-01

The regularities of the changes of horizontal and sub-horizontal systems of cracks at different locations of Holovyne labradorite deposits are studied. The trend for stress to increase has been established in the quarry LLS "Optima" for Holovyne labradorite deposits in Volodar-Volynsk district, Zhytomyr region at the deepening of excavation. The duration of the working cycle of borehole drilling in a solid and cracked massif is calculated using a new method. The calendar planning method of mining is developed taking into account the dependence of drilling efficiency on horizontal and sub-horizontal systems of cracks.

Environmental and socioeconomic assessment of impacts by mining activities-a case study in the Certej River catchment, Western Carpathians, Romania.

PubMed

Zobrist, Jürg; Sima, Mihaela; Dogaru, Diana; Senila, Marin; Yang, Hong; Popescu, Claudia; Roman, Cecilia; Bela, Abraham; Frei, Linda; Dold, Bernhard; Balteanu, Dan

2009-08-01

In the region of the Apuseni Mountains, part of the Western Carpathians in Romania, metal mining activities have a long-standing tradition. These mining industries created a clearly beneficial economic development in the region. But their activities also caused impairments to the environment, such as acid mine drainage (AMD) resulting in long-lasting heavy metal pollution of waters and sediments. The study, established in the context of the ESTROM programme, investigated the impact of metal mining activities both from environmental and socioeconomic perspectives and tried to incorporate the results of the two approaches into an integrated proposition for mitigation of mining-related issues. The small Certej catchment, situated in the Southern Apuseni Mountains, covers an area of 78 km(2). About 4,500 inhabitants are living in the basin, in which metal mining was the main economic sector. An open pit and several abandoned underground mines are producing heavy metal-loaded acidic water that is discharged untreated into the main river. The solid wastes of mineral processing plants were deposited in several dumps and tailings impoundment embodying the acidic water-producing mineral pyrite. The natural science team collected samples from surface waters, drinking water from dug wells and from groundwater. Filtered and total heavy metals, both after enrichment, and major cations were analysed by inductively coupled plasma optical emission spectroscopy (ICP-OES). Major anions in waters, measured by ion chromatography, alkalinity and acidity were determined by titration. Solid samples were taken from river sediments and from the largest tailings dam. The latter were characterised by X-ray fluorescence and X-ray diffraction. Heavy metals in sediments were analysed after digestion. Simultaneously, the socioeconomic team performed a household survey to evaluate the perception of people related to the river and drinking water pollution by way of a logistic regression analysis. The inputs of acid mine waters drastically increased filtered heavy metal concentrations in the Certej River, e.g. Zn up to 130 mg L(-1), Fe 100 mg L(-1), Cu 2.9 mg L(-1), Cd 1.4 mg L(-1) as well as those of SO(4) up to 2.2 g L(-1). In addition, river water became acidic with pH values of pH 3. Concentrations of pollutant decreased slightly downstream due to dilution by waters from tributaries. Metal concentrations measured at headwater stations reflect background values. They fell in the range of the environmental quality standards proposed in the EU Water Framework Directive for dissolved heavy metals. The outflow of the large tailing impoundment and the groundwater downstream from two tailings dams exhibited the first sign of AMD, but they still had alkalinity. Most dug wells analysed delivered a drinking water that exhibited no sign of AMD pollution, although these wells were a distance of 7 to 25 m from the contaminated river. It seems that the Certej River does not infiltrate significantly into the groundwater. Pyrite was identified as the main sulphide mineral in the tailings dam that produces acidity and with calcite representing the AMD-neutralising mineral. The acid-base accounting proved that the potential acid-neutralising capacity in the solid phases would not be sufficient to prevent the production of acidic water in the future. Therefore, the open pits and mine waste deposits have to be seen as the sources for AMD at the present time, with a high long-term potential to produce even more AMD in the future. The socioeconomic study showed that mining provided the major source of income. Over 45% of the households were partly or completely reliant on financial compensations as a result of mine closure. Unemployment was considered by the majority of the interviewed persons as the main cause of social problems in the area. The estimation of the explanatory factors by the logistic regression analysis revealed that education, household income, pollution conditions during the last years and familiarity with environmental problems were the main predictors influencing peoples' opinion concerning whether the main river is strongly polluted. This model enabled one to predict correctly 77% of the observations reported. For the drinking water quality model, three predictors were relevant and they explained 66% of the observations. Coupling the findings from the natural science and socioeconomic approaches, we may conclude that the impact of mining on the Certej River water is high, while drinking water in wells is not significantly affected. The perceptions of the respondents to pollution were to a large extent consistent with the measured results. The results of the study can be used by various stakeholders, mainly the mining company and local municipalities, in order to integrate them in their post-mining measures, thereby making them aware of the potential long-term impact of mining on the environment and on human health as well as on the local economy.

Defining the Cubature Changes of Historic St. Kinga Chamber in Bochnia Salt Mine, Using Laser Scanning Technology

NASA Astrophysics Data System (ADS)

Szafarczyk, Anna; Gawałkiewicz, Rafał

2018-03-01

In Poland, there are many mining enterprises, of historic character registered in the UNESCO World Heritage List. One of the oldest mining enterprises in Poland is the Salt Mine in Bochnia. The processes inside the rock mass require that surveying services carry out regular geometric control of the cavities. A particular attention should be paid (due to its sacral function) on St. Kinga Chamber, located 195 metres below the surface, on the mine level "August". So far measurement technologies have been connected with the studies on changes in the geometry of cavities and based on linear bases used to measure convergence. This only provides discrete information (in a point) and not always presents a real state of deformation. In the scanning method, in practice a three dimension image of changes (structural deformations) is obtained, impossible to determine with the application of measurement methods, applied to measure the value of linear convergence (the method with a limited number of bases). Laser scanning, apart from determining the value of volume convergence, gives also the possibility of the visualization of 3D cavern. Moreover, it provides direct information to update mining numerical maps and make it possible to generate various cross-sections through the cavern. The authors analysed the possibility of the application of laser scanning (scanner Faro Focus 3D), as a modern tool allowing the measuring of the value of volume convergence.

RANWAR: rank-based weighted association rule mining from gene expression and methylation data.

PubMed

Mallik, Saurav; Mukhopadhyay, Anirban; Maulik, Ujjwal

2015-01-01

Ranking of association rules is currently an interesting topic in data mining and bioinformatics. The huge number of evolved rules of items (or, genes) by association rule mining (ARM) algorithms makes confusion to the decision maker. In this article, we propose a weighted rule-mining technique (say, RANWAR or rank-based weighted association rule-mining) to rank the rules using two novel rule-interestingness measures, viz., rank-based weighted condensed support (wcs) and weighted condensed confidence (wcc) measures to bypass the problem. These measures are basically depended on the rank of items (genes). Using the rank, we assign weight to each item. RANWAR generates much less number of frequent itemsets than the state-of-the-art association rule mining algorithms. Thus, it saves time of execution of the algorithm. We run RANWAR on gene expression and methylation datasets. The genes of the top rules are biologically validated by Gene Ontologies (GOs) and KEGG pathway analyses. Many top ranked rules extracted from RANWAR that hold poor ranks in traditional Apriori, are highly biologically significant to the related diseases. Finally, the top rules evolved from RANWAR, that are not in Apriori, are reported.

30 CFR 72.620 - Drill dust control at surface mines and surface areas of underground mines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... collared and drilled wet, or other effective dust control measures shall be used, when drilling non-water-soluble material. Effective dust control measures shall be used when drilling water-soluble material. ...

30 CFR 72.620 - Drill dust control at surface mines and surface areas of underground mines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... collared and drilled wet, or other effective dust control measures shall be used, when drilling non-water-soluble material. Effective dust control measures shall be used when drilling water-soluble material. ...

30 CFR 72.620 - Drill dust control at surface mines and surface areas of underground mines.

Code of Federal Regulations, 2012 CFR

2012-07-01

... collared and drilled wet, or other effective dust control measures shall be used, when drilling non-water-soluble material. Effective dust control measures shall be used when drilling water-soluble material. ...

30 CFR 72.620 - Drill dust control at surface mines and surface areas of underground mines.

Code of Federal Regulations, 2014 CFR

2014-07-01

... collared and drilled wet, or other effective dust control measures shall be used, when drilling non-water-soluble material. Effective dust control measures shall be used when drilling water-soluble material. ...

30 CFR 72.620 - Drill dust control at surface mines and surface areas of underground mines.

Code of Federal Regulations, 2013 CFR

2013-07-01

... collared and drilled wet, or other effective dust control measures shall be used, when drilling non-water-soluble material. Effective dust control measures shall be used when drilling water-soluble material. ...

Influence of the biochar application for the recovery of Spanish mine area

NASA Astrophysics Data System (ADS)

Gascó Guerrero, Gabriel; Álvarez Calvo, María Luisa; Paz-Ferreiro, Jorge; César Arranz, Julio; Saa, Antonio; Méndez, Ana

2017-04-01

The use of organic amendment areas has been a very common technique for the restoration of land affected by mining activities. Recent years, the use of biochar for the treatment of metal-contaminated soils can be an adequate strategy due to biochar can decrease the trace metal mobility. This effect depends on biochar properties as cation exchange capacity, surface area or pH which are highly related with the raw material and pyrolysis conditions. The aim of this work is to study soil response after the use of 4 different biochars in the treatment of different soil samples collected in the Rio Tinto area (Spain) which is the main Spanish Cu mine since 15 years ago. For this purpose, biochars were added to the different soils at a dosage of 8 wt%, and samples were incubated during 6 months. After this period, the influence of biochar on trace metal mobility was assessed. The study was completed determining microbial biomass, soil respiration and several enzymes activities to study the biochar influence on soil biochemical activities. We are very grateful to Ministerio de Economía y Competitividad (Spain) for financial support under Project CGL2014-58322-R.

Investigation of fugitive dust emissions from nepheline syenite mine tailings near Nephton, Ontario

NASA Astrophysics Data System (ADS)

Ogungbemide, Damilare Immanuel

A set of experiments was designed to investigate the factors--atmospheric and surficial--controlling fugitive dust emissions from the tailings ponds of UNIMIN Canada, a mining company that extracts and produces nepheline syenite (feldspar) at two adjacent sites (Nephton and Blue Mountain) located north of Havelock, Ontario. Using wind tunnel measurements, the combined influence of relative humidity and temperature (represented by the absolute matric potential, |psi|) on dust emission was quantified and modeled. About 300 experimental runs were conducted under various conditions of wind speed (4.5-6.25 ms -1), temperature (0-30°C) and relative humidity (10-70%). Generally, dust flux decreased as a logarithmic function of matric potential, with dust emission strongly suppressed for RH > 60% or |psi|<70 MPa. Field measurements also confirmed the role of relative humidity in suppressing dust emission. Irrigation, which is widely used by mines to control dust emissions, reduced ambient dust concentration at the study site only about 60% of the time, with the highest mitigation efficiencies (average of 90%) occurring when the total depth of water applied intermittently over a few hours was greater than 10 mm. In the absence of emergent vegetation, the terrestrial laser scanning (TLS) technique proved to be a promising method for detecting and estimating both spatial and temporal moisture content changes in the field environment, particularly for the very thin surface layer, which is the most important layer for dust emission. It is hoped that the results from this study will help mines to optimize their dust management programs for the range of climate and topographic conditions found at their sites, and also serve as a source of useful information and input data for atmospheric dispersion models, such as AERMOD and CALPUFF, whose accuracy depends on the quality of the input data such as the emission rate.

NDVI (Normalized Difference Vegetation Index) signatures of transient ecohydrological systems: The case of post-mining landscapes

NASA Astrophysics Data System (ADS)

Brück, Yasemine; Schulte Overberg, Philipp; Pohle, Ina; Hinz, Christoph

2017-04-01

Assessing ecohydrological systems that undergo state transitions due to environmental change is becoming increasingly important. One system that can be used to study severe disturbances are post-mining landscapes as they usually are associated with complete removal of vegetation and afterwards subsequent ecosystem restoration or spontaneous rehabilitation in line with natural succession. Within this context it is of interest, whether and how (fast) the land cover in these areas returns to conditions comparable to those in the undisturbed surrounding or those prior mining. Many aspects of mine site rehabilitation depend on climatic, geomorphic and ecological settings, which determine at which rate vegetation may be re-established. In order to identify general patterns of vegetation establishment, we propose to use NDVI (Normalized Difference Vegetation Index) time series for mine affected land to estimate rate of recovery across climate regions and ecoregions. In this study we analysed the MODIS Terra Satellite 8 day-composite NDVI for areas influenced by surface mining in different climates from 2001 to 2015. The locations have been chosen based on their extent and the data availability of mining and rehabilitation activities. We selected coal extraction as a case study as strip mining generates well-defined chronosequences of disturbance. The selected mining areas are located in equatorial, arid, warm temperate or snow climates with different precipitation and temperature conditions according to the Köppen-Geiger classification. We analysed the NDVI time series regarding significant characteristics of the re-vegetation phase. We applied hierarchical cluster analysis to capture the spatial heterogeneity between different pixels (ca. 250 * 250 m2 each) in and around each open cast mine. We disentangled seasonality, trend and residual components in the NDVI time series by Seasonal and Trend decomposition using LOESS. As expected the time of the removal of vegetation can be clearly identified from the NDVI time series and provides the starting point of disturbance. The cluster analysis allowed us to distinguish between the non-mining land, the mine and the restored land of different ages. Based on these clusters, the time series decomposition revealed the dominance of the trend of increasing NDVI in areas undergoing the restoration process as well as the prevailing seasonality of the oldest restored sites. The determined phase of a dominant trend component, lasting until the NDVI is in the range of the surrounding landscape or the pre-mining conditions, is in the scale of a decade. The impacts of different hydroclimatic regimes and different rehabilitation strategies on long term NDVI development are currently being investigated. Furthermore, coherence analysis will be applied to quantify short term influences of hydrometeorological variables on vegetation development.

Data Mining for Financial Applications

NASA Astrophysics Data System (ADS)

Kovalerchuk, Boris; Vityaev, Evgenii

This chapter describes Data Mining in finance by discussing financial tasks, specifics of methodologies and techniques in this Data Mining area. It includes time dependence, data selection, forecast horizon, measures of success, quality of patterns, hypothesis evaluation, problem ID, method profile, attribute-based and relational methodologies. The second part of the chapter discusses Data Mining models and practice in finance. It covers use of neural networks in portfolio management, design of interpretable trading rules and discovering money laundering schemes using decision rules and relational Data Mining methodology.

Development and application of the Safe Performance Index as a risk-based methodology for identifying major hazard-related safety issues in underground coal mines

NASA Astrophysics Data System (ADS)

Kinilakodi, Harisha

The underground coal mining industry has been under constant watch due to the high risk involved in its activities, and scrutiny increased because of the disasters that occurred in 2006-07. In the aftermath of the incidents, the U.S. Congress passed the Mine Improvement and New Emergency Response Act of 2006 (MINER Act), which strengthened the existing regulations and mandated new laws to address the various issues related to a safe working environment in the mines. Risk analysis in any form should be done on a regular basis to tackle the possibility of unwanted major hazard-related events such as explosions, outbursts, airbursts, inundations, spontaneous combustion, and roof fall instabilities. One of the responses by the Mine Safety and Health Administration (MSHA) in 2007 involved a new pattern of violations (POV) process to target mines with a poor safety performance, specifically to improve their safety. However, the 2010 disaster (worst in 40 years) gave an impression that the collective effort of the industry, federal/state agencies, and researchers to achieve the goal of zero fatalities and serious injuries has gone awry. The Safe Performance Index (SPI) methodology developed in this research is a straight-forward, effective, transparent, and reproducible approach that can help in identifying and addressing some of the existing issues while targeting (poor safety performance) mines which need help. It combines three injury and three citation measures that are scaled to have an equal mean (5.0) in a balanced way with proportionate weighting factors (0.05, 0.15, 0.30) and overall normalizing factor (15) into a mine safety performance evaluation tool. It can be used to assess the relative safety-related risk of mines, including by mine-size category. Using 2008 and 2009 data, comparisons were made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performance as compared to large- and medium-sized mines. The accident rates (NDL IR, NFDL IR, SM/100) of very small and small mines in 2008 and 2009 were less than those of medium and large mines. The data indicates a heavy occurrence of very severe injuries in a number of very small and small mines. In another application which is a part of this research, the six normalized safety measures and the SPI are used to evaluate the risk that existed at mines in the two years preceding the occurrence of a fatality. This mine safety performance tracking method could have been helpful to the companies, state agency, or MSHA in recognizing and addressing emerging problems with actions that may have been able to prevent high-risk conditions, the fatality, and/or other serious injuries. The approach would have given scrutiny to the risk of mines that encompassed 74% of the fatalities during 2007-2010. In order to assess the SPI as a comparable risk measurement tool, a traditional risk approach is also developed using data embracing frequency and severity in the final equation to analyze the relative risk for all underground coal mines for the years 2007--2010. Then, the SPI is compared with this traditional risk analysis method to demonstrate that the results attained by either method provide the relative safety-related risk of underground coal mines regarding injuries and citations for violations of regulations. The comparison reveals that the SPI does emulate a traditional approach to risk analysis. A correlation coefficient of --0.89 or more was observed between the results of these two methodologies and either can be used to assist companies, the Mine Safety and Health Administration (MSHA), or state agencies in target-ing mines with high risk for serious injuries and elevated citations for remediation of their injury and/or violation experience. The SPI, however, provides a more understandable approach for mine operators to apply using measures compatible with MSHA's enforcement tools. These methodologies form an all-encompassing approach that can be used to assist companies, the MSHA, or state agencies in targeting mines with high risk for serious injuries and elevated citations. Once targeted as high risk, mines can then pursue appropriate intervention to remediate their violation and/or injury experience. This research may help in plugging the gap in the safety system and better pursue the goal of zero fatalities and serious injuries in the underground coal mines.

Analysis of Mining Terrain Deformation Characteristics with Deformation Information System

NASA Astrophysics Data System (ADS)

Blachowski, Jan; Milczarek, Wojciech; Grzempowski, Piotr

2014-05-01

Mapping and prediction of mining related deformations of the earth surface is an important measure for minimising threat to surface infrastructure, human population, the environment and safety of the mining operation itself arising from underground extraction of useful minerals. The number of methods and techniques used for monitoring and analysis of mining terrain deformations is wide and increasing with the development of geographical information technologies. These include for example: terrestrial geodetic measurements, global positioning systems, remote sensing, spatial interpolation, finite element method modelling, GIS based modelling, geological modelling, empirical modelling using the Knothe theory, artificial neural networks, fuzzy logic calculations and other. The aim of this paper is to introduce the concept of an integrated Deformation Information System (DIS) developed in geographic information systems environment for analysis and modelling of various spatial data related to mining activity and demonstrate its applications for mapping and visualising, as well as identifying possible mining terrain deformation areas with various spatial modelling methods. The DIS concept is based on connected modules that include: the spatial database - the core of the system, the spatial data collection module formed by: terrestrial, satellite and remote sensing measurements of the ground changes, the spatial data mining module for data discovery and extraction, the geological modelling module, the spatial data modeling module with data processing algorithms for spatio-temporal analysis and mapping of mining deformations and their characteristics (e.g. deformation parameters: tilt, curvature and horizontal strain), the multivariate spatial data classification module and the visualization module allowing two-dimensional interactive and static mapping and three-dimensional visualizations of mining ground characteristics. The Systems's functionality has been presented on the case study of a coal mining region in SW Poland where it has been applied to study characteristics and map mining induced ground deformations in a city in the last two decades of underground coal extraction and in the first decade after the end of mining. The mining subsidence area and its deformation parameters (tilt and curvature) have been calculated and the latter classified and mapped according to the Polish regulations. In addition possible areas of ground deformation have been indicated based on multivariate spatial data analysis of geological and mining operation characteristics with the geographically weighted regression method.

Hydrogeochemical investigations of some historic mining areas in the western Humboldt River basin, Nevada

USGS Publications Warehouse

Nash, J.T.

2001-01-01

Productive historic mines in 13 mining districts, of many geochemical types, were investigated in May of 1998. Reconnaissance field observations were made and samples of mine dumps, mine drainage waters, and mill tailings have been collected to characterize the geochemical signature of these materials and to determine their actual or potential contamination of surface or ground waters. Field observations suggest that visible indicators of acidic mine drainage are rare, and field measurements of pH and chemical analyses of several kinds of materials indicate that only a few sites release acid or significant concentrations of metals.

Reconstruction of the 2015 Atacama Floods: Influence of Legacy Mining Deposits in the Salado River Mouth

NASA Astrophysics Data System (ADS)

Fuenzalida Callejas, M. J.; Contreras Vargas, M. T.; Escauriaza, C. R.

2016-12-01

In March 2015, the Salado watershed in the Atacama Desert was affected by unusual storms that unleashed floods never recorded before in northern Chile. Chañaral, an urban center located at the mouth of the Salado River, suffered the most catastrophic consequences on the population and infrastructure. Several natural and anthropic factors contributed to the magnitude and effects observed in this event. The total precipitation, of more than 80 mm in the upper section of the basin, produced a massive and rapid hyperconcentrated flow from the Andean foothills, which propagated along the channel with high velocities, depositing more than 2 m of mud in Chañaral. The dynamics of the flood in the city was also influenced by mine tailings deposited at the river mouth. The mining industry in this region during the previous century deposited approximately 200 million tons of mine tailings in the Chañaral Bay. The accumulation of this legacy mining deposits at the river mouth changed the local morphodynamics, which exacerbated the impacts of the flood. The objective of this work is to improve our understanding of the factors that affect the hydrodynamic of floods in hyper-arid regions. We perform numerical simulations using data collected in the field to reconstruct the event of March 2015 in Chañaral, integrating hydrological and hydrodynamic models to propagate the hydrograph in the city with high resolution. By using the reconstruction of the hydrograph and peak flow estimated by Wilcox et al., 2016, we simulate the flood using a two-dimensional model of the shallow-water equations, fully coupled with the sediment concentration (Contreras & Escauriaza, 2016). To identify the influence of the tailing deposits on the flow hydrodynamics, we use high-resolution data of the pre- and post-disaster topography. We compare the performance of different methodologies to assess the destructive power of the flood, considering also the influence of the sediment concentration in the flow. Work supported by Fondecyt grant 1130940 and CONICYT/FONDAP grant 15110017.

Comparison of peak discharges among sites with and without valley fills for the July 8-9, 2001 flood in the headwaters of Clear Fork, Coal River basin, mountaintop coal-mining region, southern West Virginia

USGS Publications Warehouse

Wiley, Jeffrey B.; Brogan, Freddie D.

2003-01-01

The effects of mountaintop-removal mining practices on the peak discharges of streams were investigated in six small drainage basins within a 7-square-mile area in southern West Virginia. Two of the small basins had reclaimed valley fills, one basin had reclaimed and unreclaimed valley fills, and three basins did not have valley fills. Indirect measurements of peak discharge for the flood of July 8-9, 2001, were made at six sites on streams draining the small basins. The sites without valley fills had peak discharges with 10- to 25-year recurrence intervals, indicating that rainfall intensities and totals varied among the study basins. The flood-recurrence intervals for the three basins with valley fills were determined as though the peak discharges were those from rural streams without the influence of valley fills, and ranged from less than 2 years to more than 100 years.

Effects of organic amendments on the mobility of Pb and Zn from mine tailings added to semi-arid soils.

PubMed

Barajas-Aceves, M; Rodríguez-Vázquez, R

2013-01-01

The effects of mine tailings and three organic amendments (compost, bokashi and vermicompost) on the mobility factor for Pb and Zn and on the potential C and N mineralization in semi-arid agricultural and rangeland soils were examined. During the experiment, soil samples were analyzed periodically for CO(2)-C evolution, inorganic N, dehydrogenase activity and percent Pb and Zn mobility during 169 d of incubation. The dehydrogenase activity and CO(2)-C evolved were strongly inhibited by mine tailings mixed with organic compost in both agricultural and rangeland soils (37 to 43 %), followed by N mineralization in treatments with mine tailings plus bokashi or compost (13 to 26.5 %) at 169 d incubation. The highest % mobility of Pb and Zn were observed in soils amended with mine tailings alone, while the lowest was observed in agricultural soils treated with vermicompost plus mine tailings. The CO(2)-C evolved was fitted to first order E, while the cumulative N mineralization was fitted to the linearized power function. Mine tailings were found to influence the potential C and N mineralization rate constants in both soils. The models for C and N mineralization could be used to evaluate the effects of mine tailings, which include intrinsic parameters in the soil.

Adult tooth loss for residents of US coal mining and Appalachian counties.

PubMed

Hendryx, Michael; Ducatman, Alan M; Zullig, Keith J; Ahern, Melissa M; Crout, Richard

2012-12-01

The authors compared rates of tooth loss between adult residents of Appalachian coal-mining areas and other areas of the nation before and after control for covariate risks. The authors conducted a cross-sectional secondary data analysis that merged 2006 national Behavioral Risk Factor Surveillance System data (BRFSS) (N = 242 184) with county coal-mining data and other county characteristics. The hypothesis tested was that adult tooth loss would be greater in Appalachian mining areas after control for other risks. Primary independent variables included main effects for coal-mining present (yes/no) residence in Appalachia (yes/no), and their interaction. Data were weighted using the BRFSS final weights and analyzed using SUDAAN Proc Multilog to account for the multilevel complex sampling structure. The odds of two measures of tooth loss were examined controlling for age, race\\ethnicity, drinking, smoking, income, education, supply of dentists, receipt of dental care, fluoridation rate, and other variables. After covariate adjustment, the interaction variable for the residents of Appalachian coal-mining counties showed a significantly elevated odds for any tooth loss [odds ratio (OR) = 1.19, 95% CI = 1.02, 1.38], and greater tooth loss measured by a 4-level edentulism scale (OR = 1.20, 95% CI = 1.05, 1.36). The main effect for Appalachia was also significant for both measures, but the main effect for coal mining was not. Greater risk of tooth loss among adult residents of Appalachian coal-mining areas is present and is not explained by differences in reported receipt of dental care, fluoridation rates, supply of dentists or other behavioral or socioeconomic risks. Possible contributing factors include mining-specific disparities related to access, behavior or environmental exposures. © 2012 John Wiley & Sons A/S.

Case study of controlled recirculation at a Wyoming trona mine

PubMed Central

Pritchard, C.; Scott, D.; Frey, G.

2015-01-01

Controlled recirculation has been used in the metal/nonmetal mining industry for energy savings when heating and cooling air, in undersea mining and for increasing airflow to mining areas. For safe and effective use of controlled district recirculation, adequate airflow to dilute contaminants must exist prior to implementation, ventilation circuit parameters must be accurately quantified, ventilation network modeling must be up to date, emergency planning scenarios must be performed and effective monitoring and control systems must be installed and used. Safety and health issues that must be considered and may be improved through the use of controlled district recirculation include blasting fumes, dust, diesel emissions, radon and contaminants from mine fires. Controlled recirculation methods are expected to become more widely used as mines reach greater working depths, requiring that these health and safety issues be well understood. The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted two controlled recirculation tests over three days at a Wyoming trona mine, utilizing an inline booster fan to improve airflow to a remote and difficult-to-ventilate development section. Test results were used to determine the effect that recirculation had on air qualities and quantities measured in that section and in other adjacent areas. Pre-test conditions, including ventilation quantities and pressures, were modeled using VnetPC. During each test, ventilation quantities and pressures were measured, as well as levels of total dust. Sulfur hexafluoride (SF6) tracer gas was used to simulate a mine contaminant to monitor recirculation wave cycles. Results showed good correlation between the model results and measured values for airflows, pressure differentials, tracer gas arrival times, mine gasses and dust levels. PMID:26251567

Vegetation community composition in wetlands created following oil sand mining in Alberta, Canada.

PubMed

Roy, Marie-Claude; Foote, Lee; Ciborowski, Jan J H

2016-05-01

Reclaiming wetlands following open pit mining for industrial oil sand extraction is challenging due to the physical and chemical conditions of the post-mined landscape. The aim of our study was to examine and compare the influence of oil sands process water (OSPW) and material (fine fluid tails or FFT) on the plant community composition of created wetlands. Compared to created-unamended and natural wetlands, the created wetlands amended with OSPW and/or FFT (created-tailings wetlands) had significantly higher water salinity, conductivity, dissolved oxygen concentration and lower oxidative-reductive potential. Water chemistry parameters of created-unamended did not differ significantly from those of natural wetlands. The sediment of created wetlands had significantly less moisture, total nitrogen, and organic content than the natural wetlands. The application of OSPW/FFT in created wetlands will likely lead to initial vegetation composition atypical of natural regional wetlands. For the objective of reclaiming vegetation composition to the status of natural regional wetlands, unamended wetlands were the best reclamation option, based on the physical and chemical parameters measured. Despite being the favored reclamation option, created-unamended wetlands' physical and chemical characteristics remain atypical of natural wetlands. Most significantly, the basin morphometry of created wetlands was significantly different from that of naturally-formed wetlands in the region, and this appears to partly explain difference in vegetation composition. We also demonstrate that species richness alone is not a useful measure in wetland monitoring. Instead, plant community composition is a better indicator of wetland conditions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Human Influences on Geomorphic Dynamics in Western Montana Gravel-Bed Rivers

NASA Astrophysics Data System (ADS)

Wilcox, A. C.

2016-12-01

Management of river ecosystems, river restoration, climate-change vulnerability assessments, and other applications require understanding of how current channel conditions and processes compare to historical ranges of variability. This is particularly true with respect to evaluation of sediment balances, including of whether and how current sediment supply compares to background conditions. In western Montana, management and restoration efforts are in some cases driven by the perception that anthropogenic activities have elevated sediment yields above background levels; human-induced erosional increases have been documented in certain environments, but empirical supporting evidence is lacking for western Montana rivers. Here, human-induced changes in channel form and in sediment balances, including flow, sediment supply, and erosion rates, are evaluated for rivers in western Montana, with a particular focus on the Clark Fork and Bitterroot Rivers. These rivers are characteristic of systems in the northern Rocky Mountains with gravel beds, historically wandering channel patterns, modest bed-material loads, and land uses including logging, mining, and agriculture. The Clark Fork is influenced by legacy mining-related sediments and associated contaminants, remediation efforts, and the 2008 removal of Milltown Dam. These influences have caused temporary shifts in sediment balances, but overall, sediment fluxes are modest (e.g., suspended sediment fluxes of 6 tonnes km-2 yr-1 at the USGS Turah gage). The Bitterroot River is influenced by a mix of glaciated and unglaciated landscapes with fire-dominated erosional regimes and larger sand supply than the Clark Fork, reflecting lithologic differences; erosion rates, and the imprint of anthropogenic activities on sediment dynamics, are being investigated. This work has implications for river restoration, including whether measures are needed to impose channel stability, and for evaluating how climate-change-induced changes in fire, runoff, and erosion will alter fluvial sediment balances.

Chemical and microbial properties in contaminated soils around a magnesite mine in northeast China

Treesearch

D Yang; D-H Zeng; J Zhang; L-J Li; R. Mao

2012-01-01

We measured soil chemical and microbial properties at a depth of 0–20 cm among mine tailings, abandoned mined land, contaminated cropland, and uncontaminated cropland around a magnesite mine near Haicheng City, Liaoning Province, China. The objective was to clarify the impact of Mg on the soils. We found that soluble Mg2+ concentration and pH...

Estimation of m.w.e (meter water equivalent) depth of the salt mine of Slanic Prahova, Romania

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitrica, B.; Margineanu, R.; Stoica, S.

2010-11-24

A new mobile detector was developed in IFIN-HH, Romania, for measuring muon flux at surface and in underground. The measurements have been performed in the salt mines of Slanic Prahova, Romania. The muon flux was determined for 2 different galleries of the Slanic mine at different depths. In order to test the stability of the method, also measurements of the muon flux at surface at different altitudes were performed. Based on the results, the depth of the 2 galleries was established at 610 and 790 m.w.e. respectively.

Data Mining in Cyber Operations

DTIC Science & Technology

2014-07-01

information processing units intended to mimic the network of neurons in the human brain for performing pattern recognition  Self- organizing maps (SOM...patterns are mined from in order to influence the learning model . An exploratory attack does not alter the training process , but rather uses other...New Jersey: Prentice Hall. 21) Kohonen, T. (1982). Self- organized formation of topologically correct feature maps. Biological Cybernetics , 43, 59–69

Data Mining the Corporate Dental System of USA DENTAC Fort Bragg

DTIC Science & Technology

2016-06-10

Data Mining the Corporate Dental System of USA DENTAC Fort Bragg FREDWIN HOLOMON, D.D.S. B.S. University of...AEGD Program Director ABSTRACT Statement of the problem: Dental wellness has not reached optimum levels at Fort Bragg after implementation of...the Go First Class Program. Purpose: To examine the Go First Class Program’s influence upon dental wellness and readiness. Materials and Methods

Simulation and Measurement of Medium-Frequency Signals Coupling From a Line to a Loop Antenna

PubMed Central

Damiano, Nicholas W.; Li, Jingcheng; Zhou, Chenming; Brocker, Donovan E.; Qin, Yifeng; Werner, Douglas H.; Werner, Pingjuan L.

2016-01-01

The underground-mining environment can affect radio-signal propagation in various ways. Understanding these effects is especially critical in evaluating communications systems used during normal mining operations and during mine emergencies. One of these types of communications systems relies on medium-frequency (MF) radio frequencies. This paper presents the simulation and measurement results of recent National Institute for Occupational Safety and Health (NIOSH) research aimed at investigating MF coupling between a transmission line (TL) and a loop antenna in an underground coal mine. Two different types of measurements were completed: 1) line-current distribution and 2) line-to-antenna coupling. Measurements were taken underground in an experimental coal mine and on a specially designed surface test area. The results of these tests are characterized by current along a TL and voltage induced in the loop from a line. This paper concludes with a discussion of issues for MF TLs. These include electromagnetic fields at the ends of the TL, connection of the ends of the TL, the effect of other conductors underground, and the proximity of coal or earth. These results could help operators by providing examples of these challenges that may be experienced underground and a method by which to measure voltage induced by a line. PMID:27784954

What can 35 years and over 700,000 measurements tell us about noise exposure in the mining industry?

PubMed

Roberts, Benjamin; Sun, Kan; Neitzel, Richard L

2017-01-01

To analyse over 700,000 cross-sectional measurements from the Mine Safety and Health Administration (MHSA) and develop statistical models to predict noise exposure for a worker. Descriptive statistics were used to summarise the data. Two linear regression models were used to predict noise exposure based on MSHA-permissible exposure limit (PEL) and action level (AL), respectively. Twofold cross validation was used to compare the exposure estimates from the models to actual measurement. The mean difference and t-statistic was calculated for each job title to determine whether the model predictions were significantly different from the actual data. Measurements were acquired from MSHA through a Freedom of Information Act request. From 1979 to 2014, noise exposure has decreased. Measurements taken before the implementation of MSHA's revised noise regulation in 2000 were on average 4.5 dBA higher than after the law was implemented. Both models produced exposure predictions that were less than 1 dBA different than the holdout data. Overall noise levels in mines have been decreasing. However, this decrease has not been uniform across all mining sectors. The exposure predictions from the model will be useful to help predict hearing loss in workers in the mining industry.

Research of Cemented Paste Backfill in Offshore Environments

NASA Astrophysics Data System (ADS)

Wang, Kun; Yang, Peng; Lyu, Wensheng; Lin, Zhixiang

2018-01-01

To promote comprehensive utilization of mine waste tailings and control ground pressure, filling mine stopes with cement paste backfill (CPB) is becoming the most widely used and applicable method in contemporary underground mining. However, many urgent new problems have arisen during the exploitation in offshore mines owing to the complex geohydrology conditions. A series of rheological, settling and mechanical tests were carried out to study the influences of bittern ions on CPB properties in offshore mining. The results showed that: (1) the bittern ion compositions and concentrations of backfill water sampled in mine filling station were similar to seawater. Backfill water mixed CPB slurry with its higher viscosity coefficient was adverse to pipeline gravity transporting; (2) Bleeding rate of backfill water mixed slurry was lower than that prepared with tap water at each cement-tailings ratio; (3) The UCS values of backfill water mixed samples were higher at early curing ages (3d, 7d) and then became lower after longer curing time at 14d and 28d. Therefore, for mine production practice, the offshore environments can have adverse effects on the pipeline gravity transporting and have positive effects on stope dewatering process and early-age strength growth.

Assessment of Mine Water Quality Using Heavy Metal Pollution Index in a Coal Mining Area of Damodar River Basin, India.

PubMed

Mahato, Mukesh Kumar; Singh, Gurdeep; Singh, Prasoon Kumar; Singh, Abhay Kumar; Tiwari, Ashwani Kumar

2017-07-01

A total no. of 16 mine water (underground and opencast coal mine pump discharges) samples were collected from East Bokaro coalfield during pre-monsoon, monsoon and post-monsoon seasons. The concentrations of Fe, Mn, Cu, Pb, Zn, Ni, As, Se, Al, Cd and Cr were determined using inductively coupled plasma mass spectrometry for the assessment of spatio-temporal variations, source apportionment and heavy metal pollution indexing. The results demonstrated that concentrations of the metals showed significant seasonality and most variables exhibited higher levels in the pre-monsoon season. The principle component analysis for ionic source identification was synthesized into three factors with eigen values cut off at greater than unity and explained about 64.8% of the total variance. The extracted factors seemed to be associated to the geogenic, extensive mining and allied transportation sources of the elements. The heavy metal pollution index (HPI) of the mine water calculated for the individual locations varied from 7.1 to 49.5. Most of the locations fall under low to medium classes of HPI except few locations which are under the influence of surface mining and associated transportation.

Mercury and arsenic in the gold mining regions of the Ankobra River basin in Ghana

NASA Astrophysics Data System (ADS)

Bannerman, W.; Potin-Gautier, M.; Amoureux, D.; Tellier, S.; Rambaud, A.; Babut, M.; Adimado, A.; Beinhoff, C.

2003-05-01

The river Ankobra flows through the principal gold mining centres in Western Ghana, draining a total area of 8272 km^2 to join the Atlantic ocean. Mercury is used by thousands of small-scale miners in the region to amalgamate gold. Ores mined in some deep shafts and surface mines are arsenopyrites and the region is marked by the presence of heaps of arsenic - rich mine tailings from both past and recent activities. This study was conducted to assess the impact of mining activities on the distribution and speciation of arsenic and mercury in the aquatic environment of the Ankobra River. In all, water (filtered and non-filtered) and bed sediments were collected from various locations within the watershed. Principal parameters investigated include total mercury, arsenic (III), arsenic (V), monomethylarsonic acid (MMAA) and dimethylarsinic acid (DMAA). Seasonal and spatial variations of these parameters were investigated. Quality control systems were adopted at both the environmental and analytical stages of the study. ln general, areas close to the mining centres are the most pollilited. As (V)/As (III) ratios in water are reversed after the first 100-km of the river length with the onset of industrial influence downstream.

Atmospheric monitoring at abandoned mercury mine sites in Asturias (NW Spain).

PubMed

Loredo, Jorge; Soto, Jorge; Alvarez, Rodrigo; Ordóñez, Almudena

2007-07-01

Mercury concentrations are usually significant in historic Hg mining districts all over the world, so the atmospheric environment is potentially affected. In Asturias, northern Spain, past mining operations have left a legacy of ruins and Hg-rich wastes, soils and sediments in abandoned sites. Total Hg concentrations in the ambient air of these abandoned mine sites have been investigated to evaluate the impact of the Hg emissions. This paper presents the synthesis of current knowledge about atmospheric Hg contents in the area of the abandoned Hg mining and smelting works at 'La Peña-El Terronal' and La Soterraña, located in Mieres and Pola de Lena districts, respectively, both within the Caudal River basin. It was found that average atmospheric Hg concentrations are higher than the background level in the area (0.1 microg Nm(-3)), reaching up to 203.7 microg Nm(-3) at 0.2 m above the ground level, close to the old smelting chimney at El Terronal mine site. Data suggest that past Hg mining activities have big influences on the increased Hg concentrations around abandoned sites and that atmospheric transfer is a major pathway for Hg cycling in these environments.

Coal mining activities change plant community structure due to air pollution and soil degradation.

PubMed

Pandey, Bhanu; Agrawal, Madhoolika; Singh, Siddharth

2014-10-01

The aim of this study was to investigate the effects of coal mining activities on the community structures of woody and herbaceous plants. The response of individual plants of community to defilement caused by coal mining was also assessed. Air monitoring, soil physico-chemical and phytosociological analyses were carried around Jharia coalfield (JCF) and Raniganj coalfield. The importance value index of sensitive species minified and those of tolerant species enhanced with increasing pollution load and altered soil quality around coal mining areas. Although the species richness of woody and herbaceous plants decreased with higher pollution load, a large number of species acclimatized to the stress caused by the coal mining activities. Woody plant community at JCF was more affected by coal mining than herbaceous community. Canonical correspondence analysis revealed that structure of herbaceous community was mainly driven by soil total organic carbon, soil nitrogen, whereas woody layer community was influenced by sulphur dioxide in ambient air, soil sulphate and soil phosphorus. The changes in species diversity observed at mining areas indicated an increase in the proportion of resistant herbs and grasses showing a tendency towards a definite selection strategy of ecosystem in response to air pollution and altered soil characteristics.

State-of-the-art study of resource characterization and planning for underground coal mining. Final technical report as of June 30, 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walton, D.; Ingham, W.; Kauffman, P.

With the rapid developments taking place in coal mining technology and due to high investment costs, optimization of the structure of underground coal mines is crucial to the success of the mining project. The structure of a mine, once it is developed, cannot be readily changed and has a decisive influence on the productivity, safety, economics, and production capacity of the mine. The Department of Energy desires to ensure that the resource characterization and planning activity for underground coal mining will focus on those areas that offer the most promise of being advanced. Thus, this project was undertaken by Managementmore » Engineers Incorporated to determine the status in all aspects of the resource characterization and planning activities for underground coal mining as presently performed in the industry. The study team conducted a comprehensive computerized literature search and reviewed the results. From this a selection of the particularly relevant sources were annotated and a reference list was prepared, catalogued by resource characterization and mine planning activity. From this data, and discussions with industry representatives, academia, and research groups, private and federal, an assessment and evaluation was made of the state-of-the-art of each element in the resource characterization and mine planning process. The results of this analysis lead to the identifcation of areas requiring research and, specifically, those areas where DOE research efforts may be focused.« less

Acid mine drainage and subsidence: effects of increased coal utilization.

PubMed Central

Hill, R D; Bates, E R

1979-01-01

The increases above 1975 levels for acid mine drainage and subsidence for the years 1985 and 2000 based on projections of current mining trends and the National Energy Plan are presented. No increases are projected for acid mine drainage from surface mines or waste since enforcement under present laws should control this problem. The increase in acid mine drainage from underground mines is projected to be 16 percent by 1985 and 10 percent by 2000. The smaller increase in 2000 over 1985 reflects the impact of the PL 95-87 abandoned mine program. Mine subsidence is projected to increase by 34 and 115 percent respectively for 1985 and 2000. This estimate assumes that subsidence will parallel the rate of underground coal production and that no new subsidence control measures are adopted to mitigate subsidence occurrence. PMID:540617

Mercury methylation at mercury mines in the Humboldt River Basin, Nevada, USA

USGS Publications Warehouse

Gray, J.E.; Crock, J.G.; Lasorsa, B.K.

2002-01-01

Total Hg and methylmercury concentrations were measured in mine-waste calcines (retorted ore), sediment, and water samples collected in and around abandoned mercury mines in western Nevada to evaluate Hg methylation at the mines and in the Humboldt River Basin. Mine-waste calcines contain total Hg concentrations as high as 14 000 ??g g-1. Stream-sediment samples collected within 1 km of the mercury mines contain total Hg concentrations as high as 170 ??g g-1, whereas stream sediments collected at a distance >5 km from the mines, and those collected from the Humboldt River and regional baseline sites, contain total Hg concentrations 8 km from the nearest mercury mines. Our data indicate little transference of Hg and methylmercury from the sediment to the water column due to the lack of mine runoff in this desert climate.

Triggering effect of mining at different horizons in the rock mass with excavations. Mathematical modeling

NASA Astrophysics Data System (ADS)

Eremin, M. O.; Makarov, P. V.

2017-12-01

On the basis of a quite simple structural model of rock mass, containing coal seams on two horizons, coal mining is numerically modeled. A finite difference numerical technique is applied. At first, mining starts at the upper horizon and then moves to the lower horizon. It is shown that a mining process at the lower horizon has a significant triggering influence on the growth of damage zones in the roof and floor at the upper horizon. The features of spatiotemporal migration of deformation activity are studied numerically. Foci of large-scale fracture are located at the boundary of the seismic silence zone and the zone where the deformation activity migrates. This boundary has an additional characteristic: the maximum gradient of rock pressure is observed in this zone.

30 CFR 74.2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Definitions. 74.2 Section 74.2 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH COAL MINE... consensus standards used worldwide. (f) Precision: the relative variability of measurements from a...

What can 35 years and over 700,000 measurements tell us about noise exposure in the mining industry?

PubMed Central

Roberts, Benjamin; Sun, Kan; Neitzel, Richard L.

2017-01-01

Objective To analyze over 700,000 cross-sectional measurements from the Mine Safety and Health Administration (MHSA) and develop statistical models to predict noise exposure for a worker. Design Descriptive statistics were used to summarize the data. Two linear regression models were used to predict noise exposure based on MSHA permissible exposure limit (PEL) and action level (AL) respectively. Two-fold cross validation was used to compare the exposure estimates from the models to actual measurements in the hold out data. The mean difference and t-statistic was calculated for each job title to determine if the model exposure predictions were significantly different from the actual data. Study Sample Measurements were acquired from MSHA through a Freedom of Information Act request. Results From 1979 to 2014 the average noise measurement has decreased. Measurements taken before the implementation of MSHA’s revised noise regulation in 2000 were on average 4.5 dBA higher than after the law came in to effect. Both models produced mean exposure predictions that were less than 1 dBA different compared to the holdout data. Conclusion Overall noise levels in mines have been decreasing. However, this decrease has not been uniform across all mining sectors. The exposure predictions from the model will be useful to help predict hearing loss in workers from the mining industry. PMID:27871188

Problems associated with noise measurements in the mining industry

NASA Astrophysics Data System (ADS)

Bauer, Eric R.; Vipperman, Jeffrey S.

2002-05-01

In response to the continuing problem of noise-induced hearing loss (NIHL) among mine workers, the National Institute for Occupational Safety and Health (NIOSH) has been conducting numerous noise- and hearing-loss research efforts in the mining industry. Research is underway to determine worker noise exposure, equipment noise, hearing loss and hearing protection use, and to evaluate engineering controls. Issues that are peculiar to the mining industry have complicated these efforts. A few of the issues that must be overcome to conduct meaningful research include constantly moving equipment, changing work environments, confined space, varying production rates, multiple noise sources, and electronic permissibility of instrumentation. This presentation will address the factors that affect the measurement and analysis of noise in the mining industry and how these factors are managed. In addition, some examples of research results will be included.

Developing image processing meta-algorithms with data mining of multiple metrics.

PubMed

Leung, Kelvin; Cunha, Alexandre; Toga, A W; Parker, D Stott

2014-01-01

People often use multiple metrics in image processing, but here we take a novel approach of mining the values of batteries of metrics on image processing results. We present a case for extending image processing methods to incorporate automated mining of multiple image metric values. Here by a metric we mean any image similarity or distance measure, and in this paper we consider intensity-based and statistical image measures and focus on registration as an image processing problem. We show how it is possible to develop meta-algorithms that evaluate different image processing results with a number of different metrics and mine the results in an automated fashion so as to select the best results. We show that the mining of multiple metrics offers a variety of potential benefits for many image processing problems, including improved robustness and validation.

Radon dynamics and reduction in an underground mine in Brazil. Implications for workers' exposure.

PubMed

Evangelista, H; Pereira, E B; Fernandes, H M; Sampaio, M

2002-01-01

This work was aimed at studying the behaviour of 222Rn in an experimental underground copper mine in Brazil with a single entrance. The 222Rn concentrations, meaured by using a dynamic radon measuring technique. varied between 30.5 Bq.m(-3), during ventilated conditions applied to the mine galleries, and 19.4 x 10(3) Bq.(-3) for non-ventilated conditions and when operational mining activities were conducted inside. High radon concentration surges were observed after blasting and drilling activities. In the cases of inadequate ventilation, it was estimated that workers could be subjected to exposures as high as 10 microSv.h(-1), only due to 222Rn and its short-lived progeny. The results show the importance of real-time measurements to evaluate radon dynamics during mining operations.

Hydrologic conditions and water-quality conditions following underground coal mining in the North Fork of the Right Fork of Miller Creek drainage basin, Carbon and Emery Counties, Utah, 2004-2005

USGS Publications Warehouse

Wilkowske, C.D.; Cillessen, J.L.; Brinton, P.N.

2007-01-01

In 2004 and 2005, the U.S. Geological Survey, in cooperation with the Bureau of Land Management, reassessed the hydrologic system in and around the drainage basin of the North Fork of the Right Fork (NFRF) of Miller Creek, in Carbon and Emery Counties, Utah. The reassessment occurred 13 years after cessation of underground coal mining that was performed beneath private land at shallow depths (30 to 880 feet) beneath the NFRF of Miller Creek. This study is a follow-up to a previous USGS study of the effects of underground coal mining on the hydrologic system in the area from 1988 to 1992. The previous study concluded that mining related subsidence had impacted the hydrologic system through the loss of streamflow over reaches of the perennial portion of the stream, and through a significant increase in dissolved solids in the stream. The previous study also reported that no substantial differences in spring-water quality resulted from longwall mining, and that no clear relationship between mining subsidence and spring discharge existed.During the summers of 2004 and 2005, the USGS measured discharge and collected water-quality samples from springs and surface water at various locations in the NFRF of Miller Creek drainage basin, and maintained a streamflow-gaging station in the NFRF of Miller Creek. This study also utilized data collected by Cyprus–Plateau Mining Corporation from 1992 through 2001.Of thirteen monitored springs, five have discharge levels that have not returned to those observed prior to August 1988, which is when longwall coal mining began beneath the NFRF of Miller Creek. Discharge at two of these five springs appears to fluctuate with wet and dry cycles and is currently low due to a drought that occurred from 1999–2004. Discharge at two other of the five springs did not increase with increased precipitation during the mid-1990s, as was observed at other monitored springs. This suggests that flowpaths to these springs may have been altered by land subsidence caused by underground coal mining. Analysis of possible impacts to the fifth spring were inconclusive due to a lack of data collected during the mid-1990s. Discharge at eight other monitored springs in the study area appears to be controlled mainly by climatic fluctuations and was generally near the value measured prior to 1988. Discharge at one of these eight springs is significantly greater than that measured during the longwall mining period. Concentrations of magnesium, calcium, sulfate, and dissolved solids at one undermined spring were elevated in relation to other springs in the study area. Dissolved solids concentration at this spring ranged from 539–709 milligrams per liter. Dissolved-solids concentration for all other springs in the study area ranged from 163 to 360 milligrams per liter and was near the median value measured prior to longwall mining beneath the NFRF of Miller Creek drainage basin.Baseflow measured at a streamflow-gaging station on the NFRF of Miller Creek located downstream of the mined area during the summer of 2004 was near 5 gallons per minute. Baseflow in 2005 increased to 7–8 gallons per minute, due to increased precipitation. This is slightly greater than the range of baseflow measured near the end of the longwall mining period which was approximately 3–5 gallons per minute.Seepage investigations carried out in the summer of 2004 and 2005 along the NFRF of Miller Creek showed a net loss of surface flow along the studied reach. Specific areas within the study reach had streamflow losses prior to longwall mining, however, the study reach as a whole was observed to gain in discharge when measured in 1986–1988, immediately before longwall mining began. The area where the greatest loss in discharge from the NFRF of Miller Creek occurred corresponds to an area where overburden (material overlying a deposit of useful geological materials or bedrock) is between 700 and 210 feet thick. Overburden thickness at the place where the streambed first dried up was approximately 600 feet thick. In 2004, approximately 1,600 ft of the streambed of the NFRF of Miller Creek was dry. Only 300 feet of the streambed was dry during the wetter year of 2005. Prior to longwall mining, no dry reaches were observed, though seepage loss was documented. Average discharge measured at a tributary to the NFRF of Miller Creek has increased from 1.6 gallons per minute measured during longwall mining to 7.2 gallons per minute measured in 2004–2005. During both years of this study, the lower reach of the stream regained flow from this tributary and from seepage gains.Water quality in the lower reach of the NFRF of Miller Creek downstream of the longwall-mined area, showed significantly higher concentrations of magnesium, calcium, sulfate, and strontium, in relation to water in the upper reach of the NFRF of Miller Creek and to the springs sampled in the area. Dissolved-solids concentration measured in the lower reach of the stream in 2004 and 2005 ranged from 1,880 to 2,220 milligrams per liter, while sulfate concentrations ranged from 1,090 to 1,320 mg/L. The maximum contaminant level for drinking water in the state of Utah for dissolved solids and sulfate is 2,000 and 1,000 mg/L respectively. Concentrations of these ions are slightly greater than those measured during and just following mining beneath the NFRF of Miller Creek drainage basin, but are significantly higher than those measured prior to mining. With the exception of strontium, dissolved metals concentrations in the NFRF of Miller Creek were similar to those measured in area springs. pH in the creek and at all spring sites was near neutral. Qualitative observations of the creek bottom suggest that mining-related activities have had little effect on vegetative growth.

Mining Survey System (MSS) - innovative solution in Polish mines. (Polish Title: Mobilna Platforma Gurnicza (MPG) - nowatorskim rozwilazaniem w polskich kopalniach)

NASA Astrophysics Data System (ADS)

Adamek, A.

2015-12-01

Mobile laser scanning technology is developing rapidly also in mining. For several years research and tests are conducted on the use of that type of measurement in the inventory of the mine shafts. The company SKALA 3D in the project 1.4 POIG by PARP undertook to create Mobile automatic steering system of spatial geometry measurements mine shafts using laser scanning technology. Its main advantage is a faithful reflection of the object being measured in just a few hours. It is based on the data flowing from laser scanners and precision inertial unit. The main problem of the research was to determine the trajectory of the passing Mobile Platforms Mining (MPG) in the shaft as accurately as possible. Unable to receive signals from satellites in the pipe shaft prevented the use of solutions known for measuring terrestrial mobile systems. The company SKALA 3D has developed a methodology for determine the trajectory of the system, based on geometrical data coming from laser scanners and readings of accelerometers and gyroscopes of inertial unit. To improve the quality and accuracy of measurements MPG is also equipped with a set of anti-vibration parts prevent the transmission of vibrations ascending while cage is moving in the shaft on the measuring system. The whole forms a calibrated system, which in a short time is able to provide spatial measurement data from the measuring shaft. The accuracy of 2-3 mm in a single measurement horizon and a few centimeters determine the position of a point on the thousandth meter below ground make the system very accurate. During the project there have been numerous research problems, including the need to define the physical references, drift of IMU whether harsh weather conditions in the shaft. However, the company SKALA 3D solved these problems and making MPG unique in the world.

Miners' Misconceptions of Flow Distribution Within Circuits as a Factor Influencing Underground Mining Accidents.

NASA Astrophysics Data System (ADS)

Passaro, Perry David

Misconceptions can be thought of as naive approaches to problem solving that are perceptually appealing but incorrect and inconsistent with scientific evidence (Piaget, 1929). One type of misconception involves flow distributions within circuits. This concept is important because miners' conceptual errors about flow distribution changes within complex circuits may be in part responsible for fatal mine disasters. Based on the theory that misconceptions of flow distribution changes within circuits were responsible for underground mine disasters involving mine ventilation circuits, a series of studies was undertaken with mining engineering students, professional mining engineers, as well as mine foremen, mine supervisors, mine rescue members, mine maintenance personnel, mining researchers and working miners to identify these conceptual errors and errors in mine ventilation procedures. Results indicate that misconceptions of flow distribution changes within circuits exist in over 70 percent of the subjects sampled. It is assumed that these misconceptions of flow distribution changes within circuits result in errors of judgment when miners are faced with inferring and changing ventilation arrangements when two or more mine sections are connected. Furthermore, it is assumed that these misconceptions are pervasive in the mining industry and may be responsible for at least two mine ventilation disasters. The findings of this study are consistent with Piaget's (1929) model of figurative and operative knowledge. This model states that misconceptions are in part due to a lack of knowledge of dynamic transformations and how to apply content information. Recommendations for future research include the development of an interactive expert system for training miners with ventilation arrangements. Such a system would meet the educational recommendations made by Piaget (1973b) by involving a hands-on approach that allows discovery, interaction, the opportunity to make mistakes and to review the cognitive concepts on which the subject relied during his manipulation of the ventilation system.

Alpha emitting radionuclides in drainage from Quinta do Bispo and Cunha Baixa uranium mines (Portugal) and associated radiotoxicological risk.

PubMed

Carvalho, Fernando P; Oliveira, João M; Faria, Isabel

2009-11-01

Two large uranium mines, Quinta do Bispo and Cunha Baixa, district of Viseu, North of Portugal, were exploited until 1991. Sulfuric acid was used for in situ uranium leaching in Cunha Baixa mine and for heap leaching of low grade ores at both mines. Large amounts of mining and milling residues were accumulated nearby. Since closure of mines, the treatment of acid mine waters has been maintained and treated water is released into surface water lines. Analysis of radionuclides in the soluble phase and in the suspended matter of water samples from the uranium mines, from the creeks receiving the discharges of mine effluents, from the rivers and from wells in this area, show an enhancement of radioactivity levels. For example, downstream the discharge of mine effluents into Castelo Stream, the concentrations of dissolved uranium isotopes and uranium daughters were up to 14 times the concentrations measured upstream; (238)U concentration in suspended particulate matter of Castelo Stream reached 72 kBq kg(-1), which is about 170 times higher than background concentrations in Mondego River. Nevertheless, radionuclide concentrations decreased rapidly to near background values within a distance of about 7 kilometers from the discharge point. Enhancement of radioactivity in underground waters was positively correlated with a decrease in water pH and with an increase of sulfate ion concentration, pointing out to Cunha Baixa mine as the source of groundwater contamination. The radiotoxic exposure risk arising from using these well waters as drinking water and as irrigation water is discussed and implementation of environmental remediation measures is advised.

Oxygen transport and pyrite oxidation in unsaturated coal-mine spoil

USGS Publications Warehouse

Guo, Weixing; Cravotta, Charles A.

1996-01-01

An understanding of the mechanisms of oxygen (02) transport in unsaturated mine spoil is necessary to design and implement effective measures to exclude 02 from pyritic materials and to control the formation of acidic mine drainage. Partial pressure of oxygen (Po2) in pore gas, chemistry of pore water, and temperature were measured at different depths in unsaturated spoil at two reclaimed surface coal mines in Pennsylvania. At mine 1, where spoil was loose, blocky sandstone, Po2 changed little with depth, decreasing from 21 volume percent (vol%) at the ground surface to a minimum of about 18 vol% at 10 m depth. At mine 2, where spoil was compacted, friable shale, Po2 decreased to less than 2 vol% at depth of about 10 m. Although pore-water chemistry and temperature data indicate that acid-forming reactions were active at both mines, the pore-gas data indicate that mechanisms for 0 2 transport were different at each mine. A numerical model was developed to simulate 02 transport and pyrite oxidation in unsaturated mine spoil. The results of the numerical simulations indicate that differences in 02 transport at the two mines can be explained by differences in the air permeability of spoil. Po2 changes little with depth if advective transport of 02 dominates as at mine 1, but decreases greatly with depth if diffusive transport of 02 dominates, as in mine 2. Model results also indicate that advective transport becomes significant if the air permeability of spoil is greater than 10-9 m2, which is expected for blocky sandstone spoil. In the advective-dominant system, thermally-induced convective air flow, as a consequence of the exothermic oxidation of pyrite, supplies the 02 to maintain high Po2 within the deep unsaturated zone.

Surface Soil Preparetion for Leguminous Plants Growing in Degraded Areas by Mining Located in Amazon Forest-Brazil

NASA Astrophysics Data System (ADS)

Irio Ribeiro, Admilson; Hashimoto Fengler, Felipe; Araújo de Medeiros, Gerson; Márcia Longo, Regina; Frederici de Mello, Giovanna; José de Melo, Wanderley

2015-04-01

The revegetation of areas degraded by mining usually requires adequate mobilization of surface soil for the development of the species to be implemented. Unlike the traditional tillage, which has periodicity, the mobilization of degraded areas for revegetation can only occur at the beginning of the recovery stage. In this sense, the process of revegetation has as purpose the establishment of local native vegetation with least possible use of inputs and superficial tillage in order to catalyze the process of natural ecological succession, promoting the reintegration of areas and minimizing the negative impacts of mining activities in environmental. In this context, this work describes part of a study of land reclamation by tin exploitation in the Amazon ecosystem in the National Forest Jamari- Rondonia Brazil. So, studied the influence of surface soil mobilization in pit mine areas and tailings a view to the implementation of legumes. The results show that the surface has areas of mobilizing a significant effect on the growth of leguminous plants, areas for both mining and to tailings and pit mine areas.

Characterization and evolution of the sediments of a Mediterranean coastal lagoon located next to a former mining area.

PubMed

García, Gregorio; Muñoz-Vera, Ana

2015-11-15

Coastal lagoons are ecosystems that are relatively enclosed water bodies under the influence of both the terrestrial and the marine environment, being vulnerable to human impacts. Human activities, such as mining extraction, are significant anthropogenic coastal stressors that can negatively affect ecosystems and communities. In light of the above, the objective of this research is to examine the influence of metal mining activities on the composition of sediments of a Mediterranean coastal lagoon, named Mar Menor. This paper presents a comprehensive characterization for grain size, mineralogy, geochemistry and organic matter of sediments of this coastal lagoon, investigating their variation along space and time. Sedimentation dynamics are ruling clearly the grain size predominant in each area of the Mar Menor coastal lagoon, determining the existence of entrainment, transport and sedimentation areas. For minerals, elements and organic matter, sedimentation dynamics are also determining their distribution. Copyright © 2015 Elsevier Ltd. All rights reserved.

The use of vibration monitoring to record the blasting works impact on buildings surrounding open-pit mines

NASA Astrophysics Data System (ADS)

Sołtys, Anna; Pyra, Józef; Winzer, Jan

2018-04-01

Environmental protection law and geological and mining law require the mineral mining plant to protect its surroundings from the effects of mining operations. This also applies to the negative impact of vibrations induced by blasting works on people and construction facilities. Effective protection is only possible if the level of this impact is known, therefore it is necessary to record it. The thesis formulated in this way has been and continues to be the guiding principle of the research works carried out in the AGH Laboratory of Blasting Work and Environmental Protection. As a result of these works are procedures for conducting preventive activities by open-pit mines in order to minimize the impact of blasting on facilities in the surrounding area. An important element of this activity is the monitoring of vibrations in constructions, which is a source of knowledge for excavation supervisors and engineers performing blasting works, thus contributing to raising the awareness of the responsible operation of the mining plant. Developed in the Laboratory of the Mine's Vibration Monitoring Station (KSMD), after several modernizations, it became a fully automated system for monitoring and recording the impact of blasting works on the surrounding environment. Currently, there are 30 measuring devices in 10 open-pit mines, and additional 8 devices are used to provide periodic measurement and recording services for the mines concerned.

New Reconstruction Technologies Of Safety Pillar In Mines / Nowoczesne Technologie Odbudowy Filara Bezpieczeństwa w Kopalniach

NASA Astrophysics Data System (ADS)

Gonet, Andrzej; Stryczek, Stanisław; Brudnik, Krzysztof

2012-11-01

Safety pillars are made around mines as a protection measure. This is especially important in salt mines where the surrounding waters are most hazardous. Without maintaining safe conditions the mine may be water-flooded as it was the case in one of the Polish mine "Wapno". An original technology linking pipeline injection and hole injection methods has been used for the reconstruction of a safety pillar in the Salt Mine "Wieliczka". This solution turned out to be successful when on 13 April 1992 the mine was saved from flooding after a disastrous water flux to the transverse working Mina. The presented technology can be efficiently used in various mines at the stage of designing, though their exploitation to the closing stage.

Effects of mining activities on evolution of water chemistry in coal-bearing aquifers in karst region of Midwestern Guizhou, China: evidences from δ13C of dissolved inorganic carbon and δ34S of sulfate.

PubMed

Li, Qingguang; Wu, Pan; Zha, Xuefang; Li, Xuexian; Wu, Linna; Gu, Shangyi

2018-04-24

The generation of acid mine drainage (AMD) may accelerate watershed erosion and promote the migration of heavy metals, then threaten local ecosystems such as aquatic life and even human health. Previous studies have focused primarily on influence of AMD in surface environment. In order to reveal the acidizing processes in karst high-sulfur coalfield in Southwest China, this study, by contrast, focused on the hydrogeochemical evolution process and acidification mechanism of mine water in Zhijin coalfield, western Guizhou Province. The oxidation of pyrite and other sulfides induced strong acidification of mine water according to the water chemical analysis. As a result, a series of geochemical processes such as dissolution of carbonates and silicates, hydrolysis of metal ions, and degassing of CO 2 complicated water chemical evolution. The dissolution of silicates controlled the chemical composition of mine water, but more carbonates might be dissolved during the acidification of mine water. The sources of sulfate are quite different in water samples collected from the two selected mine. According to sulfur isotope analysis, the dissolution of gypsum is the primary source of sulfate in samples from Hongfa mine, whereas sulfide oxidation contributed a large amount of sulfate to the mine water in Fenghuangshan mine. The dissolution of carbonates should be an important source of DIC in mine water and CO 2 originating from organic mineralization might also have a certain contribution. This study elucidated the groundwater chemical evolution processes in high-sulfur coal-bearing strata and provided a foundation for further study of carbonates erosion and carbon emission during acidification of mine water.

Sources and fates of heavy metals in a mining-impacted stream: Temporal variability and the role of iron oxides

PubMed Central

Schaider, Laurel A.; Senn, David B.; Estes, Emily R.; Brabander, Daniel J.; Shine, James P.

2014-01-01

Heavy metal contamination of surface waters at mining sites often involves complex interactions of multiple sources and varying biogeochemical conditions. We compared surface and subsurface metal loading from mine waste pile runoff and mine drainage discharge and characterized the influence of iron oxides on metal fate along a 0.9-km stretch of Tar Creek (Oklahoma, USA), which drains an abandoned Zn/Pb mining area. The importance of each source varied by metal: mine waste pile runoff contributed 70% of Cd, while mine drainage contributed 90% of Pb, and both sources contributed similarly to Zn loading. Subsurface inputs accounted for 40% of flow and 40-70% of metal loading along this stretch. Streambed iron oxide aggregate material contained highly elevated Zn (up to 27,000 μg g−1), Pb (up to 550 μg g−1) and Cd (up to 200 μg g−1) and was characterized as a heterogeneous mixture of iron oxides, fine-grain mine waste, and organic material. Sequential extractions confirmed preferential sequestration of Pb by iron oxides, as well as substantial concentrations of Zn and Cd in iron oxide fractions, with additional accumulation of Zn, Pb, and Cd during downstream transport. Comparisons with historical data show that while metal concentrations in mine drainage have decreased by more than an order of magnitude in recent decades, the chemical composition of mine waste pile runoff has remained relatively constant, indicating less attenuation and increased relative importance of pile runoff. These results highlight the importance of monitoring temporal changes at contaminated sites associated with evolving speciation and simultaneously addressing surface and subsurface contamination from both mine waste piles and mine drainage. PMID:24867708

Tree-Substrate Water Relations and Root Development in Tree Plantations Used for Mine Tailings Reclamation.

PubMed

Guittonny-Larchevêque, Marie; Bussière, Bruno; Pednault, Carl

2016-05-01

Tree water uptake relies on well-developed root systems. However, mine wastes can restrict root growth, in particular metalliferous mill tailings, which consist of the finely crushed ore that remains after valuable metals are removed. Thus, water stress could limit plantation success in reclaimed mine lands. This study evaluates the effect of substrates varying in quality (topsoil, overburden, compost and tailings mixture, and tailings alone) and quantity (50- or 20-cm-thick topsoil layer vs. 1-m plantation holes) on root development and water stress exposure of trees planted in low-sulfide mine tailings under boreal conditions. A field experiment was conducted over 2 yr with two tree species: basket willow ( L.) and hybrid poplar ( Moench × A. Henry). Trees developed roots in the tailings underlying the soil treatments despite tailings' low macroporosity. However, almost no root development occurred in tailings underlying a compost and tailings mixture. Because root development and associated water uptake was not limited to the soil, soil volume influenced neither short-term (water potential and instantaneous transpiration) nor long-term (δC) water stress exposure in trees. However, trees were larger and had greater total leaf area when grown in thicker topsoil. Despite a volumetric water content that always remained above permanent wilting point in the tailings colonized by tree roots, measured foliar water potentials at midday were lower than drought thresholds reported for both tested tree species. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Design of Compressed Sensing Algorithm for Coal Mine IoT Moving Measurement Data Based on a Multi-Hop Network and Total Variation.

PubMed

Wang, Gang; Zhao, Zhikai; Ning, Yongjie

2018-05-28

As the application of a coal mine Internet of Things (IoT), mobile measurement devices, such as intelligent mine lamps, cause moving measurement data to be increased. How to transmit these large amounts of mobile measurement data effectively has become an urgent problem. This paper presents a compressed sensing algorithm for the large amount of coal mine IoT moving measurement data based on a multi-hop network and total variation. By taking gas data in mobile measurement data as an example, two network models for the transmission of gas data flow, namely single-hop and multi-hop transmission modes, are investigated in depth, and a gas data compressed sensing collection model is built based on a multi-hop network. To utilize the sparse characteristics of gas data, the concept of total variation is introduced and a high-efficiency gas data compression and reconstruction method based on Total Variation Sparsity based on Multi-Hop (TVS-MH) is proposed. According to the simulation results, by using the proposed method, the moving measurement data flow from an underground distributed mobile network can be acquired and transmitted efficiently.

Aquatic ecosystems in Central Colorado are influenced by mineral forming processes and historical mining

USGS Publications Warehouse

Schmidt, T.S.; Church, S.E.; Clements, W.H.; Mitchell, K.A.; Fey, D. L.; Wanty, R.B.; Verplanck, P.L.; San, Juan C.A.; Klein, T.L.; deWitt, E.H.; Rockwell, B.W.

2009-01-01

Stream water and sediment toxicity to aquatic insects were quantified from central Colorado catchments to distinguish the effect of geologic processes which result in high background metals concentrations from historical mining. Our sampling design targeted small catchments underlain by rocks of a single lithology, which allowed the development of biological and geochemical baselines without the complication of multiple rock types exposed in the catchment. By accounting for geologic sources of metals to the environment, we were able to distinguish between the environmental effects caused by mining and the weathering of different mineralized areas. Elevated metal concentrations in water and sediment were not restricted to mined catchments. Impairment of aquatic communities also occurred in unmined catchments influenced by hydrothermal alteration. Hydrothermal alteration style, deposit type, and mining were important determinants of water and sediment quality and aquatic community structure. Weathering of unmined porphyry Cu-Mo occurrences resulted in water (median toxic unit (TU) = 108) and sediment quality (TU = 1.9) that exceeded concentrations thought to be safe for aquatic ecosystems (TU = 1). Metalsensitive aquatic insects were virtually absent from streams draining catchments with porphyry Cu-Mo occurrences (1.1 individuals/0.1 m2 ). However, water and sediment quality (TU = 0.1, 0.5 water and sediment, respectively) and presence of metalsensitive aquatic insects (204 individuals/0.1 m2 ) for unmined polymetallic vein occurrences were indistinguishable from that for unmined and unaltered streams (TU = 0.1, 0.5 water and sediment, respectively; 201 individuals/0.1 m2 ). In catchments with mined quartz-sericite-pyrite altered polymetallic vein deposits, water (TU = 8.4) and sediment quality (TU = 3.1) were degraded and more toxic to aquatic insects (36 individuals/0.1 m2 ) than water (TU = 0.4) and sediment quality (TU = 1.7) from mined propylitically altered polymetallic vein deposits. The sampling approach taken in this study distinguishes the effects of different mineral deposits on ecosystems and can be used to more accurately quantify the effect of mining on the environment. 

Automatic mine detection based on multiple features

NASA Astrophysics Data System (ADS)

Yu, Ssu-Hsin; Gandhe, Avinash; Witten, Thomas R.; Mehra, Raman K.

2000-08-01

Recent research sponsored by the Army, Navy and DARPA has significantly advanced the sensor technologies for mine detection. Several innovative sensor systems have been developed and prototypes were built to investigate their performance in practice. Most of the research has been focused on hardware design. However, in order for the systems to be in wide use instead of in limited use by a small group of well-trained experts, an automatic process for mine detection is needed to make the final decision process on mine vs. no mine easier and more straightforward. In this paper, we describe an automatic mine detection process consisting of three stage, (1) signal enhancement, (2) pixel-level mine detection, and (3) object-level mine detection. The final output of the system is a confidence measure that quantifies the presence of a mine. The resulting system was applied to real data collected using radar and acoustic technologies.

Mercury speciation in the Valdeazogues River-La Serena Reservoir system: influence of Almadén (Spain) historic mining activities.

PubMed

Berzas Nevado, Juan J; Rodríguez Martín-Doimeadios, Rosa C; Moreno, María Jiménez

2009-03-15

Mercury (Hg) speciation and partitioning have been investigated in a river-reservoir system impacted by the Almadén mining activities, the world's largest Hg district. This study is the first to simultaneously investigate Hg dynamics from above the mining district and into the La Serena Reservoir (3219 Hm(3)), being the third largest reservoir in Europe and the largest in Spain. Water, sediment and biota were sampled at different seasons during a 2-year study from the Valdeazogues River, which flows east-west from the mining District, to La Serena Reservoir. Simultaneously, a comprehensive study was undertaken to determine the influence of some major physico-chemical parameters that potentially influence the fate of Hg within the watershed. Concentrations of dissolved Hg in water were below 0.14 microg/L, whereas particulate Hg ranged from 0.1 to 87 microg/g, with significant seasonal variation. Total Hg concentrations varied from 7 to 74 microg/g in sediment from the Valdeazogues River, while in sediments from La Serena Reservoir were below 2 microg/g. On the other hand, methyl-Hg reached concentrations up to 0.3 ng/L in water and 6 ng/g in sediment from La Serena Reservoir, whereas maximum concentrations in Valdeazogues River were 5 ng/L and 880 ng/g in water and sediment, respectively. The distribution of Hg species in the Valdeazogues River-La Serena Reservoir system indicated a source of Hg from the mine waste distributed along the river. Total Hg in water was strongly correlated with total dissolved solids and chlorophyll a concentrations, whereas organic carbon and Fe concentrations seem to play a role in methylation of inorganic Hg in sediment. Total Hg concentrations were low in fish from Valdeazogues River (0.8-8.6 ng/g, wet weight) and bivalves from La Serena Reservoir (10-110 ng/g, wet weight), but most was present as methyl-Hg.

Effects of natural factors on the spatial distribution of heavy metals in soils surrounding mining regions.

PubMed

Ding, Qian; Cheng, Gong; Wang, Yong; Zhuang, Dafang

2017-02-01

Various studies have shown that soils surrounding mining areas are seriously polluted with heavy metals. Determining the effects of natural factors on spatial distribution of heavy metals is important for determining the distribution characteristics of heavy metals in soils. In this study, an 8km buffer zone surrounding a typical non-ferrous metal mine in Suxian District of Hunan Province, China, was selected as the study area, and statistical, spatial autocorrelation and spatial interpolation analyses were used to obtain descriptive statistics and spatial autocorrelation characteristics of As, Pb, Cu, and Zn in soil. Additionally, the distributions of soil heavy metals under the influences of natural factors, including terrain (elevation and slope), wind direction and distance from a river, were determined. Layout of sampling sites, spatial changes of heavy metal contents at high elevations and concentration differences between upwind and downwind directions were then evaluated. The following results were obtained: (1) At low elevations, heavy metal concentrations decreased slightly, then increased considerably with increasing elevation. At high elevations, heavy metal concentrations first decreased, then increased, then decreased with increasing elevation. As the slope increased, heavy metal contents increased then decreased. (2) Heavy metal contents changed consistently in the upwind and downwind directions. Heavy metal contents were highest in 1km buffer zone and decreased with increasing distance from the mining area. The largest decrease in heavy metal concentrations was in 2km buffer zone. Perennial wind promotes the transport of heavy metals in downwind direction. (3) The spatial extent of the influence of the river on Pb, Zn and Cu in the soil was 800m. (4) The influence of the terrain on the heavy metal concentrations was greater than that of the wind. These results provide a scientific basis for preventing and mitigating heavy metal soil pollution in areas surrounding mines. Copyright © 2016 Elsevier B.V. All rights reserved.

Environmental Education in Brazil: Preventive Measures to Avoid Contamination with U and Th

DOE Office of Scientific and Technical Information (OSTI.GOV)

Silva Pastura, Valeria Fonseca da; Wieland, Patricia

2008-08-07

Aiming at increasing awareness of radiation health effects, environmental issues and preventive measures, the Nuclear Energy National Commission (CNEN) launched in 2004 an education and public outreach programme for mine workers, students, teachers, governmental leaders, labor representatives and members of communities nearby small mining sites at the North and Northeast regions. Many Brazilian conventional mines present a significant risk of exposure to radiation due to Uranium and Thorium. CNEN inspects the mines but there are several small mining sites dedicated to open pit short term mineral extraction, called 'garimpagem', that are of difficult control. Therefore, information at large about preventivemore » measures to avoid contamination during exploration, transportation and storage is necessary. CNEN developed an educational campaign which includes a series of open seminars, talks, folders, booklets and posters. The objective of this paper is to present the Brazilian educational campaign to avoid contamination risks at those small mineral exploration sites and its results. This campaign is a joint task that receives collaboration of other organizations such as federal police, schools and universities.« less

Environmental Education in Brazil: Preventive Measures to Avoid Contamination with U and Th

NASA Astrophysics Data System (ADS)

da Silva Pastura, Valéria Fonseca; Wieland, Patricia

2008-08-01

Aiming at increasing awareness of radiation health effects, environmental issues and preventive measures, the Nuclear Energy National Commission (CNEN) launched in 2004 an education and public outreach programme for mine workers, students, teachers, governmental leaders, labor representatives and members of communities nearby small mining sites at the North and Northeast regions. Many Brazilian conventional mines present a significant risk of exposure to radiation due to Uranium and Thorium. CNEN inspects the mines but there are several small mining sites dedicated to open pit short term mineral extraction, called "garimpagem", that are of difficult control. Therefore, information at large about preventive measures to avoid contamination during exploration, transportation and storage is necessary. CNEN developed an educational campaign which includes a series of open seminars, talks, folders, booklets and posters. The objective of this paper is to present the Brazilian educational campaign to avoid contamination risks at those small mineral exploration sites and its results. This campaign is a joint task that receives collaboration of other organizations such as federal police, schools and universities.

Time-lapse seismic tomography using the data of microseismic monitoring network and analysis of mine-induced events, seismic tomography results and technological data in Pyhäsalmi mine, Finland

NASA Astrophysics Data System (ADS)

Nevalainen, Jouni; Kozlovskaya, Elena

2016-04-01

We present results of a seismic travel-time tomography applied to microseismic data from the Pyhäsalmi mine, Finland. The data about microseismic events in the mine is recorded since 2002 when the passive microseismic monitoring network was installed in the mine. Since that over 130000 microseismic events have been observed. The first target of our study was to test can the passive microseismic monitoring data be used with travel-time tomography. In this data set the source-receiver geometry is based on non-even distribution of natural and mine-induced events inside and in the vicinity of the mine and hence, is a non-ideal one for the travel-time tomography. The tomographic inversion procedure was tested with the synthetic data and real source-receiver geometry from Pyhäsalmi mine and with the real travel-time data of the first arrivals of P-waves from the microseismic events. The results showed that seismic tomography is capable to reveal differences in seismic velocities in the mine area corresponding to different rock types. For example, the velocity contrast between the ore body and surrounding rock is detectable. The velocity model recovered agrees well with the known geological structures in the mine area. The second target of the study was to apply the travel-time tomography to microseismic monitoring data recorded during different time periods in order to track temporal changes in seismic velocities within the mining area as the excavation proceeds. The result shows that such a time-lapse travel-time tomography can recover such changes. In order to obtain good ray coverage and good resolution, the time interval for a single tomography round need to be selected taking into account the number of events and their spatial distribution. The third target was to compare and analyze mine-induced event locations, seismic tomography results and mining technological data (for example, mine excavation plans) in order to understand the influence of mining technology to mining-induced seismicity. Acknowledgements: This study has been supported by ERDF SEISLAB project and Pyhäsalmi Mine Ltd.

Nitrous oxide emissions from a coal mine land reclaimed with stabilized manure

USDA-ARS?s Scientific Manuscript database

Mined land restoration using manure-based amendments may create soil conditions suitable for nitrous oxide production and emission. We measured nitrous oxide emissions from mine soil amended with composted poultry manure (Comp) or poultry manure mixed with paper mill sludge (Man+PMS) at C/N ratios o...

A novel method for estimating methane emissions from underground coal mines: The Yanma coal mine, China

NASA Astrophysics Data System (ADS)

Ji, Zhong-Min; Chen, Zhi-Jian; Pan, Jie-Nan; Niu, Qing-He

2017-12-01

As the world's largest coal producer and consumer, China accounts for a relatively high proportion of methane emissions from coal mines. Several estimation methods had been established for the coal mine methane (CMM) emission. However, with large regional differences, various reservoir formation types of coalbed methane (CBM) and due to the complicated geological conditions in China, these methods may be deficient or unsuitable for all the mining areas (e.g. Jiaozuo mining area). By combing the CMM emission characteristics and considering the actual situation of methane emissions from underground coal mine, we found that the methane pre-drainage is a crucial reason creating inaccurate evaluating results for most estimation methods. What makes it so essential is the extensive pre-drainage quantity and its irrelevance with annual coal production. Accordingly, the methane releases were divided into two categories: methane pre-drainage and methane release during mining. On this basis, a pioneering method for estimating CMM emissions was proposed. Taking the Yanma coal mine in the Jiaozuo mining area as a study case, the evaluation method of the pre-drainage methane quantity was established after the correlation analysis between the pre-drainage rate and time. Thereafter, the mining activity influence factor (MAIF) was first introduced to reflect the methane release from the coal and rock seams around where affected by mining activity, and the buried depth was adopted as the predictor of the estimation for future methane emissions. It was verified in the six coal mines of Jiaozuo coalfield (2011) that the new estimation method has the minimum errors of 12.11%, 9.23%, 5.77%, -5.20%, -8.75% and 4.92% respectively comparing with other methods. This paper gives a further insight and proposes a more accurate evaluation method for the CMM emissions, especially for the coal seams with low permeability and strong tectonic deformation in methane outburst coal mines.

Cu-Zn slags from Røros (Norway): a case study of rapid cooling and crystal nucleation

NASA Astrophysics Data System (ADS)

Warchulski, Rafał; Szopa, Krzysztof

2014-09-01

The mining town of Røros located in central Norway was established in 1644 and it is known of historical mining industry related to copper. Røros was designated as an UNESCO World Heritage Site in 1980 on the base of mining culture represented by, e.g., unique wooden architecture. Slag pieces are composed of three parts differing in glass to crystallites ratio. Røros slags are composed of olivine- and pyroxene- group minerals accompanied by sulphides, with glass in the interstices. Temperature gradient and volatiles content were determined as the main factor influencing crystallization process in this material

Cu-Zn Slags from R⊘ros (Norway): A Case Study of Rapid Cooling and Crystal Nucleation

NASA Astrophysics Data System (ADS)

Warchulski, Rafał; Szopa, Krzysztof

2014-09-01

The mining town of R⊘ros located in central Norway was established in 1644 and it is known of historical mining industry related to copper. R⊘ros was designated as an UNESCO World Heritage Site in 1980 on the base of mining culture represented by, e.g., unique wooden architecture. Slag pieces are composed of three parts differing in glass to crystallites ratio. R⊘ros slags are composed of olivine- and pyroxene- group minerals accompanied by sulphides, with glass in the interstices. Temperature gradient and volatiles content were determined as the main factor influencing crystallization process in this material.

Mine Winder Drives in Integrated Copper Complex

NASA Astrophysics Data System (ADS)

Dey, Pranab Kumar

2018-04-01

This paper describes various features required to be evaluated before selecting mine winder drives. In handling such project, the selection of proper equipments is necessary at the initial design stage of planning and how the electrical system design considers all aspects to protect the grid from unwarranted influence of the connected loads and minimize the generation of harmonics due to network configurations adopted to keep it within the stipulated value dictated by the supply authorities has been discussed. The design should cover all aspects to provide quality power with effective braking system required as per the mining statute for operational safety. It also emphasizes on the requirement of quality maintenance.

Effect of mine discharge on the pattern of riverine habitat use of elephants Elephas maximus and other mammals in Singhbhum forests, Bihar, India

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singh, R.K.; Chowdhury, S.

The aim of this paper is to access the influence of water quality both on the occurrence of, and utilization by, elephants (Elephas maximus) in a riverine habitat. Mining operations and other anthropogenic changes to natural river systems have caused degradation of the ecosystem for elephants. A decline in their numbers has been seen throughout the Singhbhum Forests, India due to fragmentation and loss of habitat. The need to preserve and restore the habitat of the elephant is accepted, but until the factors that influence their distribution are known and understood, suitable management plans cannot be implemented. The study areamore » was the catchment of the river Koina where waste discharge from an iron oremine and processing plant impact upon water quality. The study period from April 1995 to March 1996 looked at sections of the river where unregulated mine discharge was made, and where regulation through tailing ponds controlled total suspended solids (TSS) output from the mine waste water to the river system. Various physico-chemical parameters recorded at seven sampling stations were quantified. Principal Component Analysis (PCA) segregated the key parameters in determining the discharge levels of both regulated and unregulated discharge at various sites.« less

Miners wives: Gender, culture, and society in the south Wales coalfields, 1919-1939

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gier, J.J.

1993-01-01

This study addresses the absence of historical research on the role of women in Welsh coalfield society through the use of oral history testimony, folk culture sources, literature, newspapers, union records and comparative data from other British and Australian coalfield regions. The thesis identifies the ways in which the domestic ideology and the vernacular culture of coalfield society influenced gender roles and relations in Welsh mining communities during the interwar period. Since the myth of the Miner and the Mining Mam signified the pervasive influence of both the domestic ideology and the vernacular culture, the aim of the study wasmore » to dismantle these ideals in order to reconstruct a history of miners' wives. To further this goal a life-cycle approach was used; the thesis examined courtship an marriage practices, domestic culture in the mining household, women's customary role in ritual surrounding birth and death, and their role in mining strikes and other forms of collective action. The study concludes that while the traditions of rural Wales tended to support a broader role for women in coalfield society, the domestic ideology denied the miner's wife her identity as a worker, and thus limited her participation in class struggle and obscured her role in the history of coalfield society.« less

Mechanisms and Effectivity of Sulfate Reducing Bioreactors ...

EPA Pesticide Factsheets

Mining-influenced water (MIW) is the main environmental challenges associated with the mining industry. Passive MIW remediation can be achieved through microbial activity in sulfate-reducing bioreactors (SRBRs), but their actual removal rates depend on different factors, one of which is the substrate composition. Chitinous materials have demonstrated high metal removal rates, particularly for the two recalcitrant MIW contaminants Zn and Mn, but their removal mechanisms need further study. We studied Cd, Fe, Zn, and Mn removal in bioactive and abiotic SRBRs to elucidate the metal removal mechanisms and the differences in metal and sulfate removal rates using a chitinous material as substrate. We found that sulfate-reducing bacteria are effective in increasing metal and sulfate removal rates and duration of operation in SRBRs, and that the main mechanism involved was metal precipitation as sulfides. The solid residues provided evidence of the presence of sulfides in the bioactive column, more specifically ZnS, according to XPS analysis. The feasibility of passive treatments with a chitinous substrate could be an important option for MIW remediation. Mining influenced water (MIW) remediation is still one of the top priorities for the agency because it addresses the most important environmental problem associated with the mining industry and that affects thousands of communities in the U.S. and worldwide. In this paper, the MIW bioremediation mechanisms are studied

Stress Changes and Deformation Monitoring of Longwall Coal Pillars Located in Weak Ground

NASA Astrophysics Data System (ADS)

Yu, Bin; Zhang, Zhenyu; Kuang, Tiejun; Liu, Jinrong

2016-08-01

Coal pillar stability is strongly influenced by the site-specific geological and geotechnical conditions. Many geological structures such as faults, joints, or rock intrusions can be detrimental to mining operations. In order to evaluate the performance of coal pillars under weak roof degraded by igneous rock intrusion, stress and deformation monitoring was conducted in the affected tailgate areas of Nos. 8208 and 8210 longwalls in Tashan coal mine, Shanxi Province, China. The measurements in the 8208 longwall tailgate showed that the mining-induced stresses in 38-m-wide coal chain pillars under the overburden depth of 300-500 m started to increase at about 100 m ahead of the 8208 longwall working face and reached its peak level at approximately 50 m ahead of the longwall face. The peak stress of 9.16 MPa occurred at the depth of 8-9 m into the pillar from the tailgate side wall. In comparison, disturbance of the headgate block pillar area was negligible, indicating the difference of abutment pressure distribution between the tailgate and headgate sites where the adjacent unmined longwall block carried most of the overburden load. However, when the longwall face passed the headgate monitoring site by 360-379 m, the pillar stress increased to a peak value of 21.4 MPa at the pillar depth of 13 m from the gob side mainly due to stress redistribution in the chain pillar. In contrast to the headgate, at the tailgate side, the adjacent goaf was the dominant triggering factor for high stress concentrations in the chain pillar. Convergence measurements in the tailgate during longwall mining further indicated the evolution characteristics of coal pillar deformation, clearly showing that the gateroad deformation is mainly induced by the longwall extraction it serves. When predicting the future pillar loads from the monitored data, two stress peaks appeared across the 38-m-wide tailgate coal pillar, which are separated by the lower stress area within the pillar center. This 10-m-wide elastic pillar core area indicates that the coal pillar may be narrowed to 30 m to improve coal recovery. The measurements further indicate that, if the headgate of the next panel can be developed after the adjacent gob becomes stable, the coal pillar width may be further reduced to 20 m. This study is applicable for the chain pillar design, the gateroad secondary support design ahead of the longwall mining face, and the gateroad preparation of the next longwall panel under similar geological and geotechnical conditions.

Distributions and concentrations of thallium in surface waters of a region impacted by historical metal mining (Cornwall, UK).

PubMed

Tatsi, Kristi; Turner, Andrew

2014-03-01

Thallium is a highly toxic heavy metal whose concentrations and distributions in the aquatic environment are poorly defined. In this study, concentrations of aqueous and total Tl have been measured in water samples from a variety of rivers and effluents (the latter related to historical metal mining) in the county of Cornwall, SW England. Aqueous concentrations ranged from about 13 ng L(-1) in a river whose catchment contained no metal mines to 2,640 ng L(-1) in water abstracted directly from an abandoned mine shaft. Concentrations of Tl in rivers were greatest in the vicinity of mine-related effluents, with a maximum value measured of about 770 ng L(-1). Thallium was not efficiently removed by the conventional, active treatment of mine water, and displayed little interaction with suspended particles. Its mobility in surface waters, coupled with concentrations that are close to a quality guideline of 800 ng L(-1), is cause for concern. Accordingly, we recommend that the metal is more closely monitored in this and other regions impacted by mining activities. Copyright © 2013 Elsevier B.V. All rights reserved.

Public exposure to hazards associated with natural radioactivity in open-pit mining in Ghana.

PubMed

Darko, E O; Faanu, A; Awudu, A R; Emi-Reynolds, G; Yeboah, J; Oppon, O C; Akaho, E H K

2010-01-01

The results of studies carried out on public exposure contribution from naturally occurring radioactive materials (NORMS) in two open-pit mines in the Western and Ashanti regions of Ghana are reported. The studies were carried out under International Atomic Energy Agency-supported Technical Co-operation Project GHA/9/005. Measurements were made on samples of water, soil, ore, mine tailings and air using gamma spectrometry. Solid-state nuclear track detectors were used for radon concentration measurements. Survey was also carried out to determine the ambient gamma dose rate in the vicinity of the mines and surrounding areas. The effective doses due to external gamma irradiation, ingestion of water and inhalation of radon and ore dusts were calculated for the two mines. The average annual effective dose was found to be 0.30 +/- 0.06 mSv. The result was found to be within the levels published by other countries. The study provides a useful information and data for establishing a comprehensive framework to investigate other mines and develop guidelines for monitoring and control of NORMS in the mining industry and the environment as a whole in Ghana.

Assessment of respirable dust exposures in an opencast coal mine.

PubMed

Onder, M; Yigit, E

2009-05-01

All major opencast mining activities produce dust. The major operations that produce dust are drilling, blasting, loading, unloading, and transporting. Dust not only deteriorates the environmental air quality in and around the mining site but also creates serious health hazards. Therefore, assessment of dust levels that arise from various opencast mining operations is required to prevent and minimize the health risks. To achieve this objective, an opencast coal mining area was selected to generate site-specific emission data and collect respirable dust measurement samples. The study covered various mining activities in different locations including overburden loading, stock yard, coal loading, drilling, and coal handling plant. The dust levels were examined to assess miners' exposure to respirable dust in each of the opencast mining areas from 1994 to 2005. The data obtained from the dust measurement studies were evaluated by using analysis of variance (ANOVA) and the Tukey-Kramer procedure. The analyses were performed by using Minitab 14 statistical software. It was concluded that, drilling operations produce higher dust concentration levels and thus, drill operators may have higher incidence of respiratory disorders related to exposure to dust in their work environment.

Origin, diagnostics, and mitigation of a salt dissolution sinkhole at the US Strategic Petroleum Reserve storage site, Weeks Island, Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neal, J.T.; Myers, R.E.

1995-01-27

A sinkhole was first observed in May 1992 over the edge of the two-level former salt mine that was converted for oil storage by the US Strategic Petroleum Reserve (SPR). Diagnostic studies that included geophysical, geochemical, drilling, and hydrological methods suggest a direct connection exists between the surface collapse area and the underground mine as shown by correlative measurements of sediment slump rates and brine influx into the mine. The dissolution of salt below the sinkhole that initiated the leak into the mine was likely caused by several confluent geologic processes, and exacerbated by mining-induced stresses that created fractures whichmore » served as hydrologic flowpaths. Modeling studies of mine stresses show that years may be required before tensional cracking begins to occur, but once begun can continue to develop, and relieve the stress in that specific regime. The crack regime creates the avenue for incursion of groundwater, very slowly initially, but gradually enlarging as undersaturated groundwater dissolves salt on the sides of the crack. Mitigation measures include increasing the mine pressurization, slowing the dissolution by injecting brine into the sinkhole throat, and freeze grouting to restrict hydrologic flowpaths.« less

Evaluation of a Portable Photometer for Estimating Diesel Particulate Matter Concentrations in an Underground Limestone Mine

PubMed Central

Watts, Winthrop F.; Gladis, David D.; Schumacher, Matthew F.; Ragatz, Adam C.; Kittelson, David B.

2010-01-01

A low cost, battery-operated, portable, real-time aerosol analyzer is not available for monitoring diesel particulate matter (DPM) concentrations in underground mines. This study summarizes a field evaluation conducted at an underground limestone mine to evaluate the potential of the TSI AM 510 portable photometer (equipped with a Dorr-Oliver cyclone and 1.0-μm impactor) to qualitatively track time-weighted average mass and elemental, organic, and total carbon (TC) measurements associated with diesel emissions. The calibration factor corrected correlation coefficient (R2) between the underground TC and photometer measurements was 0.93. The main issues holding back the use of a photometer for real-time estimation of DPM in an underground mine are the removal of non-DPM-associated particulate matter from the aerosol stream using devices, such as a cyclone and/or impactor and calibration of the photometer to mine-specific aerosol. PMID:20410071

Developing Image Processing Meta-Algorithms with Data Mining of Multiple Metrics

PubMed Central

Cunha, Alexandre; Toga, A. W.; Parker, D. Stott

2014-01-01

People often use multiple metrics in image processing, but here we take a novel approach of mining the values of batteries of metrics on image processing results. We present a case for extending image processing methods to incorporate automated mining of multiple image metric values. Here by a metric we mean any image similarity or distance measure, and in this paper we consider intensity-based and statistical image measures and focus on registration as an image processing problem. We show how it is possible to develop meta-algorithms that evaluate different image processing results with a number of different metrics and mine the results in an automated fashion so as to select the best results. We show that the mining of multiple metrics offers a variety of potential benefits for many image processing problems, including improved robustness and validation. PMID:24653748

Operational Monitoring of Mines by COSMO-SkyMed PSP SAR Interferometry

NASA Astrophysics Data System (ADS)

Costantini, Mario; Malvarosa, Fabio; Miniati, Federico; de Assis, Luciano Mozer

2016-08-01

Synthetic aperture radar (SAR) interferometry is a powerful technology for detection and monitoring of slow ground surface movements. Monitoring of ground deformations in mining structures is an important application, particularly difficult because the scene changes with time. The persistent scatterer pair (PSP) approach, recently proposed to overcome some limitations of standard persistent scatter interferometry, proved to be effective also for mine monitoring. In this work, after resuming the main ideas of the PSP method, we describe the PSP measurements obtained from high- resolution X-band COSMO-SkyMed data over a large mining area in Minas Gerais state, Brazil. The outcomes demonstrate that dense and accurate ground deformation measurements can be obtained on the mining area and its structures (such as open pits, waste dumps, conveyor belts, water and tailings dams, etc.), achieving a consistent global view including also areas where field instruments are not installed.

Vulnerability assessment and risk perception: the case of the Arieş River Middle Basin

NASA Astrophysics Data System (ADS)

Ozunu, Al.; Botezan, C.

2012-04-01

Vulnerability assessment is influenced by a number of factors, including risk perception. This paper investigates the vulnerability of people living in the middle basin of the Aries river region, a former mining area, to natural and technologic hazards. The mining industry lead to significant environmental changes, which combined with the social problems caused by its decline (high unemployment rate, low income and old age) raised the level of the vulnerability in the area. This case study is unique, as it includes an evaluation of risk perception and its influence on the social vulnerability and resilience of local communities to disasters. Key words: vulnerability assessment, natural hazards, social vulnerability, risk perception

Testing and modeling the influence of reclamation and control methods for reducing nonpoint mercury emissions associated with industrial open pit gold mines.

PubMed

Miller, Matthieu B; Gustin, Mae S

2013-06-01

Industrial gold mining is a significant source of mercury (Hg) emission to the atmosphere. To investigate ways to reduce these emissions, reclamation and dust and mercury control methods used at open pit gold mining operations in Nevada were studied in a laboratory setting. Using this information along with field data, and building off previous work, total annual Hg emissions were estimated for two active gold mines in northern Nevada. Results showed that capping mining waste materials with a low-Hg substrate can reduce Hg emissions from 50 to nearly 100%. The spraying of typical dust control solutions often results in higher Hg emissions, especially as materials dry after application. The concentrated application of a dithiocarbamate Hg control reagent appears to reduce Hg emissions, but further testing mimicking the actual distribution of this chemical within an active leach solution is needed to make a more definitive assessment.

Dietary patterns analysis using data mining method. An application to data from the CYKIDS study.

PubMed

Lazarou, Chrystalleni; Karaolis, Minas; Matalas, Antonia-Leda; Panagiotakos, Demosthenes B

2012-11-01

Data mining is a computational method that permits the extraction of patterns from large databases. We applied the data mining approach in data from 1140 children (9-13 years), in order to derive dietary habits related to children's obesity status. Rules emerged via data mining approach revealed the detrimental influence of the increased consumption of soft dinks, delicatessen meat, sweets, fried and junk food. For example, frequent (3-5 times/week) consumption of all these foods increases the risk for being obese by 75%, whereas in children who have a similar dietary pattern, but eat >2 times/week fish and seafood the risk for obesity is reduced by 33%. In conclusion patterns revealed from data mining technique refer to specific groups of children and demonstrate the effect on the risk associated with obesity status when a single dietary habit might be modified. Thus, a more individualized approach when translating public health messages could be achieved. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Effects of iron on arsenic speciation and redox chemistry in acid mine water

USGS Publications Warehouse

Bednar, A.J.; Garbarino, J.R.; Ranville, J.F.; Wildeman, T.R.

2005-01-01

Concern about arsenic is increasing throughout the world, including areas of the United States. Elevated levels of arsenic above current drinking-water regulations in ground and surface water can be the result of purely natural phenomena, but often are due to anthropogenic activities, such as mining and agriculture. The current study correlates arsenic speciation in acid mine drainage and mining-influenced water with the important water-chemistry properties Eh, pH, and iron(III) concentration. The results show that arsenic speciation is generally in equilibrium with iron chemistry in low pH AMD, which is often not the case in other natural-water matrices. High pH mine waters and groundwater do not always hold to the redox predictions as well as low pH AMD samples. The oxidation and precipitation of oxyhydroxides deplete iron from some systems, and also affect arsenite and arsenate concentrations through sorption processes. ?? 2004 Elsevier B.V. All rights reserved.

Novel Microbial Assemblages Dominate Weathered Sulfide-Bearing Rock from Copper-Nickel Deposits in the Duluth Complex, Minnesota, USA

PubMed Central

Lapakko, Kim A.; Wenz, Zachary J.; Olson, Michael C.; Roepke, Elizabeth W.; Novak, Paige J.; Bailey, Jake V.

2017-01-01

ABSTRACT The Duluth Complex in northeastern Minnesota hosts economically significant deposits of copper, nickel, and platinum group elements (PGEs). The primary sulfide mineralogy of these deposits includes the minerals pyrrhotite, chalcopyrite, pentlandite, and cubanite, and weathering experiments show that most sulfide-bearing rock from the Duluth Complex generates moderately acidic leachate (pH 4 to 6). Microorganisms are important catalysts for metal sulfide oxidation and could influence the quality of water from mines in the Duluth Complex. Nevertheless, compared with that of extremely acidic environments, much less is known about the microbial ecology of moderately acidic sulfide-bearing mine waste, and so existing information may have little relevance to those microorganisms catalyzing oxidation reactions in the Duluth Complex. Here, we characterized the microbial communities in decade-long weathering experiments (kinetic tests) conducted on crushed rock and tailings from the Duluth Complex. Analyses of 16S rRNA genes and transcripts showed that differences among microbial communities correspond to pH, rock type, and experimental treatment. Moreover, microbial communities from the weathered Duluth Complex rock were dominated by taxa that are not typically associated with acidic mine waste. The most abundant operational taxonomic units (OTUs) were from the genera Meiothermus and Sulfuriferula, as well as from diverse clades of uncultivated Chloroflexi, Acidobacteria, and Betaproteobacteria. Specific taxa, including putative sulfur-oxidizing Sulfuriferula spp., appeared to be primarily associated with Duluth Complex rock, but not pyrite-bearing rocks subjected to the same experimental treatment. We discuss the implications of these results for the microbial ecology of moderately acidic mine waste with low sulfide content, as well as for kinetic testing of mine waste. IMPORTANCE Economic sulfide mineral deposits in the Duluth Complex may represent the largest undeveloped source of copper and nickel on Earth. Microorganisms are important catalysts for sulfide mineral oxidation, and research on extreme acidophiles has improved our ability to manage and remediate mine wastes. We found that the microbial assemblages associated with weathered rock from the Duluth Complex are dominated by organisms not widely associated with mine waste or mining-impacted environments, and we describe geochemical and experimental influences on community composition. This report will be a useful foundation for understanding the microbial biogeochemistry of moderately acidic mine waste from these and similar deposits. PMID:28600313

Novel Microbial Assemblages Dominate Weathered Sulfide-Bearing Rock from Copper-Nickel Deposits in the Duluth Complex, Minnesota, USA.

PubMed

Jones, Daniel S; Lapakko, Kim A; Wenz, Zachary J; Olson, Michael C; Roepke, Elizabeth W; Sadowsky, Michael J; Novak, Paige J; Bailey, Jake V

2017-08-15

The Duluth Complex in northeastern Minnesota hosts economically significant deposits of copper, nickel, and platinum group elements (PGEs). The primary sulfide mineralogy of these deposits includes the minerals pyrrhotite, chalcopyrite, pentlandite, and cubanite, and weathering experiments show that most sulfide-bearing rock from the Duluth Complex generates moderately acidic leachate (pH 4 to 6). Microorganisms are important catalysts for metal sulfide oxidation and could influence the quality of water from mines in the Duluth Complex. Nevertheless, compared with that of extremely acidic environments, much less is known about the microbial ecology of moderately acidic sulfide-bearing mine waste, and so existing information may have little relevance to those microorganisms catalyzing oxidation reactions in the Duluth Complex. Here, we characterized the microbial communities in decade-long weathering experiments (kinetic tests) conducted on crushed rock and tailings from the Duluth Complex. Analyses of 16S rRNA genes and transcripts showed that differences among microbial communities correspond to pH, rock type, and experimental treatment. Moreover, microbial communities from the weathered Duluth Complex rock were dominated by taxa that are not typically associated with acidic mine waste. The most abundant operational taxonomic units (OTUs) were from the genera Meiothermus and Sulfuriferula , as well as from diverse clades of uncultivated Chloroflexi , Acidobacteria , and Betaproteobacteria Specific taxa, including putative sulfur-oxidizing Sulfuriferula spp., appeared to be primarily associated with Duluth Complex rock, but not pyrite-bearing rocks subjected to the same experimental treatment. We discuss the implications of these results for the microbial ecology of moderately acidic mine waste with low sulfide content, as well as for kinetic testing of mine waste. IMPORTANCE Economic sulfide mineral deposits in the Duluth Complex may represent the largest undeveloped source of copper and nickel on Earth. Microorganisms are important catalysts for sulfide mineral oxidation, and research on extreme acidophiles has improved our ability to manage and remediate mine wastes. We found that the microbial assemblages associated with weathered rock from the Duluth Complex are dominated by organisms not widely associated with mine waste or mining-impacted environments, and we describe geochemical and experimental influences on community composition. This report will be a useful foundation for understanding the microbial biogeochemistry of moderately acidic mine waste from these and similar deposits. Copyright © 2017 American Society for Microbiology.

Soil physical properties: Key factors for successful reclamation of disturbed landscapes

NASA Astrophysics Data System (ADS)

Krümmelbein, Julia; Raab, Thomas

2013-04-01

The practice of open cast mining, e.g. for lignite, results in major landscape disturbances and especially affects soils because relocation and subsequent mixing of naturally developed soil horizons leads to areas with extremely altered soil properties compared to the undisturbed conditions. Various reclamation measures are applied to recover the reconstructed landscape for different land use options. Major parts of the post mining landscapes are used for agriculture, agroforestry or silviculture, the remaining voids of the coal mines fill successively with groundwater after mine closure and are or will be used mainly for touristic and leisure purposes. Small proportions of the post mining areas are left for natural succession, or habitats for endangered flora and fauna are initiated. In reclamation research, many studies have focused on soil chemical and biological constraints of post mining substrates and investigated factors such as unsuitable pH, in many cases very low pH, (poor) nutrient contents and (poor) biological activity. But the initial and developing soil physical parameters and functions are also key factors for the success of reclamation practices. The soil water and gas balance influence strongly the suitability of a site for the intended future land use. The mechanical stability of the soil determines the rigidity of the pore system against deforming forces and thereby the persistence of soil functions, such as water and air permeability over time. The amendment of unfavourable (initial) soil physical properties is in most cases more complex and time-consuming than e.g. optimization of pH or fertilization with nutrients. Moreover, regarding the suitability of a site e.g. as a habitat for plants or microorganisms, poor physical pre-conditions can turn substrates with perfect nutrient contents and composition and pH into infertile locations of very low productivity. We show results of an on-going field study where the effects of different agricultural reclamation measures on initial soil physical properties and their development are investigated. Site reconstruction creates the preconditions for the soil physical development, which depends on the subsequent soil disturbance, e.g. due to tillage and on the vegetation/crop rotation. We recommend that the process of site reconstruction should be accomplished with highest possible accuracy and pre-caution. Suitable vegetation, e.g. deep and intense rooting crops should be established and the mechanically unstable sites should be protected from heavy loads and intensive soil tillage operations to facilitate the development of soil structure in the course of reclamation.

Mercury and methylmercury contamination related to artisanal gold mining, Suriname

USGS Publications Warehouse

Gray, J.E.; Labson, V.F.; Weaver, J.N.; Krabbenhoft, D.P.

2002-01-01

Elemental Hg-Au amalgamation mining practices are used widely in many developing countries resulting in significant Hg contamination of surrounding ecosystems. We have measured total Hg and methyl-Hg concentrations in sediment and water collected from artisanal Au mines and these are the first Hg speciation data from such mines in Suriname. Total Hg and methyl-Hg contents in mine-waste sediment and water are elevated over local uncontaminated baselines. Total Hg (10-930 ng/L) and methyl-Hg (0.02-3.8 ng/L) are highly elevated in mine waters. Increasing total Hg contents in discharged mine waters correlate with increasing water turbidity indicating that most Hg transport is on suspended particulates. Our Hg results are similar to those found in artisanal Au mines in the Amazon basin, where Hg contamination has led to adverse effects on tropical ecosystems.

Questa Baseline and Pre-Mining Ground-Water Quality Investigation. 13. Mineral Microscopy and Chemistry of Mined and Unmined Porphyry Molybdenum Mineralization Along the Red River, New Mexico: Implications for Ground- and Surface-Water Quality

USGS Publications Warehouse

Plumlee, Geoff; Lowers, Heather; Ludington, Steve; Koenig, Alan; Briggs, Paul

2005-01-01

This report is one in a series presenting results of an interdisciplinary U.S. Geological Survey (USGS) study of ground-water quality in the lower Red River watershed prior to open-pit and underground molybdenite mining at Molycorp's Questa mine. The stretch of the Red River watershed that extends from just upstream of the town of Red River to just above the town of Questa includes several mineralized areas in addition to the one mined by Molycorp. Natural erosion and weathering of pyrite-rich rocks in the mineralized areas has created a series of erosional scars along this stretch of the Red River that contribute acidic waters, as well as mineralized alluvial material and sediments, to the river. The overall goal of the USGS study is to infer the pre-mining ground-water quality at the Molycorp mine site. An integrated geologic, hydrologic, and geochemical model for ground water in the mineralized but unmined Straight Creek drainage is being used as an analogue for the geologic, geochemical, and hydrologic conditions that influenced ground-water quality and quantity at the mine site prior to mining. This report summarizes results of reconnaissance mineralogical and chemical characterization studies of rock samples collected from the various scars and the Molycorp open pit, and of drill cuttings or drill core from bedrock beneath the scars and adjacent debris fans.

Development of a Universal Safety Behavior Management System for Coal Mine Workers

PubMed Central

LI, Jizu; LI, Yuejiao; LIU, Xiaoguang

2015-01-01

Background: In China, over 80% of all work-related deaths in the mining industry occur in coal mines and human factors constitute 85% of the direct causes of coal mine accidents, which indicates that significant shortcomings currently exist in the safety behavior management of Chinese coal mine workers. We aimed to verify the impact of human psychological behavior in coal mine accidents systematically through experimental study, theoretical analysis and management application. Methods: Four test instruments (Sensory and cognitive capacity test, Sixteen-Personal Factor Questionnaire, Symptom Checklist 90 Questionnaire and the supervisors’ evaluation) were employed from November 2013 to June 2014 to identify unsafe behavior factors, the self-established Questionnaire of Safety Behavior Norms (QSBN) was also used to propose the safety behavior countermeasures of coal mine employees. Results: The mental health of most coal mine workers’ is relatively poor. The sensory and cognitive capacity of those in different work posts varies greatly, as does the sense of responsibility. Workers are susceptible to external influences, and score low in site management. When the 16-PF and SCL-90 sensory and cognitive assessments were combined, the psychological index predictive power was greatest for estimating sense of efficiency and degree of satisfaction in internal evaluations, while at the same time lowest for estimating control of introversion-extroversion and stress character. Conclusion: The psychological indicators can predict part of employee safety behavior, and assist a coal mine enterprise to recruit staff, develop occupational safety norms and improve the working environment. PMID:26258088

Application of the Deformation Information System for automated analysis and mapping of mining terrain deformations - case study from SW Poland

NASA Astrophysics Data System (ADS)

Blachowski, Jan; Grzempowski, Piotr; Milczarek, Wojciech; Nowacka, Anna

2015-04-01

Monitoring, mapping and modelling of mining induced terrain deformations are important tasks for quantifying and minimising threats that arise from underground extraction of useful minerals and affect surface infrastructure, human safety, the environment and security of the mining operation itself. The number of methods and techniques used for monitoring and analysis of mining terrain deformations is wide and expanding with the progress in geographical information technologies. These include for example: terrestrial geodetic measurements, Global Navigation Satellite Systems, remote sensing, GIS based modelling and spatial statistics, finite element method modelling, geological modelling, empirical modelling using e.g. the Knothe theory, artificial neural networks, fuzzy logic calculations and other. The presentation shows the results of numerical modelling and mapping of mining terrain deformations for two cases of underground mining sites in SW Poland, hard coal one (abandoned) and copper ore (active) using the functionalities of the Deformation Information System (DIS) (Blachowski et al, 2014 @ http://meetingorganizer.copernicus.org/EGU2014/EGU2014-7949.pdf). The functionalities of the spatial data modelling module of DIS have been presented and its applications in modelling, mapping and visualising mining terrain deformations based on processing of measurement data (geodetic and GNSS) for these two cases have been characterised and compared. These include, self-developed and implemented in DIS, automation procedures for calculating mining terrain subsidence with different interpolation techniques, calculation of other mining deformation parameters (i.e. tilt, horizontal displacement, horizontal strain and curvature), as well as mapping mining terrain categories based on classification of the values of these parameters as used in Poland. Acknowledgments. This work has been financed from the National Science Centre Project "Development of a numerical method of mining ground deformation modelling in complex geological and mining conditions" UMO-2012/07/B/ST10/04297 executed at the Faculty of Geoengineering, Mining and Geology of the Wroclaw University of Technology (Poland).

Differential affinities of MinD and MinE to anionic phospholipid influence Min Patterning dynamics in vitro

PubMed Central

Vecchiarelli, Anthony G.; Li, Min; Mizuuchi, Michiyo; Mizuuchi, Kiyoshi

2014-01-01

The E. coli Min system forms a cell-pole-to-cell-pole oscillator that positions the divisome at mid-cell. The MinD ATPase binds the membrane and recruits the cell division inhibitor MinC. MinE interacts with and releases MinD (and MinC) from the membrane. The chase of MinD by MinE creates the in vivo oscillator that maintains a low level of the division inhibitor at mid-cell. In vitro reconstitution and visualization of Min proteins on a supported lipid bilayer has provided significant advances in understanding Min patterns in vivo. Here we studied the effects of flow, lipid composition, and salt concentration on Min patterning. Flow and no-flow conditions both supported Min protein patterns with somewhat different characteristics. Without flow, MinD and MinE formed spiraling waves. MinD and, to a greater extent MinE, have stronger affinities for anionic phospholipid. MinD-independent binding of MinE to anionic lipid resulted in slower and narrower waves. MinE binding to the bilayer was also more susceptible to changes in ionic strength than MinD. We find that modulating protein diffusion with flow, or membrane binding affinities with changes in lipid composition or salt concentration, can differentially affect the retention time of MinD and MinE, leading to spatiotemporal changes in Min patterning. PMID:24930948

30 CFR 62.174 - Follow-up corrective measures when a standard threshold shift is detected.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Follow-up corrective measures when a standard threshold shift is detected. 62.174 Section 62.174 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR UNIFORM MINE HEALTH REGULATIONS OCCUPATIONAL NOISE EXPOSURE § 62.174 Follow-up corrective measures when a standard...

30 CFR 62.174 - Follow-up corrective measures when a standard threshold shift is detected.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Follow-up corrective measures when a standard threshold shift is detected. 62.174 Section 62.174 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR UNIFORM MINE HEALTH REGULATIONS OCCUPATIONAL NOISE EXPOSURE § 62.174 Follow-up corrective measures when a standard...

30 CFR 62.174 - Follow-up corrective measures when a standard threshold shift is detected.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Follow-up corrective measures when a standard threshold shift is detected. 62.174 Section 62.174 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR UNIFORM MINE HEALTH REGULATIONS OCCUPATIONAL NOISE EXPOSURE § 62.174 Follow-up corrective measures when a standard...

30 CFR 62.174 - Follow-up corrective measures when a standard threshold shift is detected.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Follow-up corrective measures when a standard threshold shift is detected. 62.174 Section 62.174 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR UNIFORM MINE HEALTH REGULATIONS OCCUPATIONAL NOISE EXPOSURE § 62.174 Follow-up corrective measures when a standard...

LLNL electro-optical mine detection program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, C.; Aimonetti, W.; Barth, M.

1994-09-30

Under funding from the Advanced Research Projects Agency (ARPA) and the US Marine Corps (USMC), Lawrence Livermore National Laboratory (LLNL) has directed a program aimed at improving detection capabilities against buried mines and munitions. The program has provided a national test facility for buried mines in arid environments, compiled and distributed an extensive data base of infrared (IR), ground penetrating radar (GPR), and other measurements made at that site, served as a host for other organizations wishing to make measurements, made considerable progress in the use of ground penetrating radar for mine detection, and worked on the difficult problem ofmore » sensor fusion as applied to buried mine detection. While the majority of our effort has been concentrated on the buried mine problem, LLNL has worked with the U.S.M.C. on surface mine problems as well, providing data and analysis to support the COBRA (Coastal Battlefield Reconnaissance and Analysis) program. The original aim of the experimental aspect of the program was the utilization of multiband infrared approaches for the detection of buried mines. Later the work was extended to a multisensor investigation, including sensors other than infrared imagers. After an early series of measurements, it was determined that further progress would require a larger test facility in a natural environment, so the Buried Object Test Facility (BOTF) was constructed at the Nevada Test Site. After extensive testing, with sensors spanning the electromagnetic spectrum from the near ultraviolet to radio frequencies, possible paths for improvement were: improved spatial resolution providing better ground texture discrimination; analysis which involves more complicated spatial queueing and filtering; additional IR bands using imaging spectroscopy; the use of additional sensors other than IR and the use of data fusion techniques with multi-sensor data; and utilizing time dependent observables like temperature.« less

Stabilization of metals in acidic mine spoil with amendments and red fescue (Festuca rubra L.) growth.

PubMed

Simon, László

2005-12-01

Stabilization of metals with amendments and red fescue (Festuca rubra, cv. Keszthelyi 2) growth was studied on an acidic and phytotoxic mine spoil (pH(KCl) 3.20-3.26; Cd 7.1 mg kg(-1), Cu 120 mg kg(-1), Pb 2154 mg kg(-1) and Zn 605 mg kg(-1)) from Gyöngyösoroszi, Hungary in a pot experiment. Raising the pH above 5.0 by lime (CaCO(3)), and supplementing with 40 mg kg(-1)nitrogen (NH(4)NO(3)) made this material suitable for plant growth. All cultures were limed with 0.5% (m/m) CaCO(3) (treatment 1), which was combined with 5% (m/m) municipal sewage sludge compost (treatment 2), 5% (m/m) peat (treatment 3), 7.5% (m/m) natural zeolite (clinoptilolite) (treatment 4), and 0.5 (m/m) KH(2)PO(4) (treatment 5). Treatments 1-5 were combined with each other (treatment 6). After 60 days of red fescue growth, pH of the limed mine spoil decreased in all cultures units. Application of peat caused the highest pH decrease (1.15), while decrease of pH was less than 0.23 in treatments 2, 5 or 6. Application of lime significantly reduced concentrations of metals in the 'plant available' fraction of mine spoil compared to non-limed mine spoil. Amendments added to limed mine spoil changed variously the ratio of Cd, Cu, Pb and Zn in exchangeable or 'plant available' fractions, differently influencing the phytoavailability of these metals. Most of the metals were captured in the roots of test plants. Treatment 2 caused the appearance of less Cd in shoots (<0.1 microg g(-1)) or roots (3.11 microg g(-1)), while treatment 5 resulted in the highest Cd concentration (2.13 microg g(-1)) in shoots. Treatments did not influence significantly the Cu accumulation in shoots. The Pb accumulation of roots (44.7 microg g(-1)) was most effectively inhibited by combined treatment, while the highest value (136 microg g(-1)) was found in the culture treated with potassium phosphate. Pb concentration in shoots was below the detection limit, except for treatments 5 and 6. Peat application resulted in higher Zn concentration (448 microg g(-1)) in shoots than other amendments, where these values were around 100 microg g(-1). All amendments influenced positively the dry matter yield of red fescue grown in limed mine spoil, however the application of 0.5 phosphate was less favourable. Liming, application of amendments and growth of red fescue can stabilize metals in acidic and phytotoxic mine spoil, and by phytostabilization they can reduce the risk of metal contamination of the food chain.

Perception of Air Pollution in the Jinchuan Mining Area, China: A Structural Equation Modeling Approach

PubMed Central

Li, Zhengtao; Folmer, Henk; Xue, Jianhong

2016-01-01

Studies on the perception of air pollution in China are very limited. The aim of this paper is to help to fill this gap by analyzing a cross-sectional dataset of 759 residents of the Jinchuan mining area, Gansu Province, China. The estimations suggest that perception of air pollution is two-dimensional. The first dimension is the perceived intensity of air pollution and the second is the perceived hazardousness of the pollutants. Both dimensions are influenced by environmental knowledge. Perceived intensity is furthermore influenced by socio-economic status and proximity to the pollution source; perceived hazardousness is influenced by socio-economic status, family health experience, family size and proximity to the pollution source. There are no reverse effects from perception on environmental knowledge. The main conclusion is that virtually all Jinchuan residents perceive high intensity and hazardousness of air pollution despite the fact that public information on air pollution and its health impacts is classified to a great extent. It is suggested that, to assist the residents to take appropriate preventive action, the local government should develop counseling and educational campaigns and institutionalize disclosure of air quality conditions. These programs should pay special attention to young residents who have limited knowledge of air pollution in the Jinchuan mining area. PMID:27455291

Approximate classification of mining tremors harmfulness based on free-field and building foundation vibrations

NASA Astrophysics Data System (ADS)

Kuzniar, Krystyna; Stec, Krystyna; Tatara, Tadeusz

2018-04-01

The paper compares the results of an approximate evaluation of mining tremors harmfulness performed on the basis of free-field and simultaneously measured building foundation vibrations. The focus is on the office building located in the Upper Silesian Basin (USB). The empirical Mining Intensity Scale GSI-GZWKW-2012 has been applied to classify the harmfulness of the rockbursts. This scale is based on the measurements of free-field vibrations but, for research purposes, it was also used in the cases of building foundation vibrations. The analysis was carried out using the set of 156 pairs ground - foundation of velocity vibration records as well as the set of 156 pairs of acceleration records induced by the same mining tremors.

Mining Adverse Drug Reactions in Social Media with Named Entity Recognition and Semantic Methods.

PubMed

Chen, Xiaoyi; Deldossi, Myrtille; Aboukhamis, Rim; Faviez, Carole; Dahamna, Badisse; Karapetiantz, Pierre; Guenegou-Arnoux, Armelle; Girardeau, Yannick; Guillemin-Lanne, Sylvie; Lillo-Le-Louët, Agnès; Texier, Nathalie; Burgun, Anita; Katsahian, Sandrine

2017-01-01

Suspected adverse drug reactions (ADR) reported by patients through social media can be a complementary source to current pharmacovigilance systems. However, the performance of text mining tools applied to social media text data to discover ADRs needs to be evaluated. In this paper, we introduce the approach developed to mine ADR from French social media. A protocol of evaluation is highlighted, which includes a detailed sample size determination and evaluation corpus constitution. Our text mining approach provided very encouraging preliminary results with F-measures of 0.94 and 0.81 for recognition of drugs and symptoms respectively, and with F-measure of 0.70 for ADR detection. Therefore, this approach is promising for downstream pharmacovigilance analysis.

Changes in the Bacterial Community of Soil from a Neutral Mine Drainage Channel

PubMed Central

Pereira, Letícia Bianca; Vicentini, Renato; Ottoboni, Laura M. M.

2014-01-01

Mine drainage is an important environmental disturbance that affects the chemical and biological components in natural resources. However, little is known about the effects of neutral mine drainage on the soil bacteria community. Here, a high-throughput 16S rDNA pyrosequencing approach was used to evaluate differences in composition, structure, and diversity of bacteria communities in samples from a neutral drainage channel, and soil next to the channel, at the Sossego copper mine in Brazil. Advanced statistical analyses were used to explore the relationships between the biological and chemical data. The results showed that the neutral mine drainage caused changes in the composition and structure of the microbial community, but not in its diversity. The Deinococcus/Thermus phylum, especially the Meiothermus genus, was in large part responsible for the differences between the communities, and was positively associated with the presence of copper and other heavy metals in the environmental samples. Other important parameters that influenced the bacterial diversity and composition were the elements potassium, sodium, nickel, and zinc, as well as pH. The findings contribute to the understanding of bacterial diversity in soils impacted by neutral mine drainage, and demonstrate that heavy metals play an important role in shaping the microbial population in mine environments. PMID:24796430

Prokaryotic and eukaryotic community structure affected by the presence of an acid mine drainage from an abandoned gold mine.

PubMed

Bonilla, José O; Kurth, Daniel G; Cid, Fabricio D; Ulacco, José H; Gil, Raúl A; Villegas, Liliana B

2018-04-28

The acid mine drainage that originates in the abandoned gold mine in San Luis, Argentina, is released into La Carolina stream. The aim of this study was to determine the influence of this mine drainage on the physicochemical parameters of the area studied and on both prokaryotic and eukaryotic community structure. In addition, specific relationships between microbial taxonomic groups and physicochemical parameters were established. The drainage that flows into La Carolina stream acidifies the stream and increases its sulfate, Zn, Cd and Te concentrations. Microbial analysis showed that prokaryotic community structure is mainly affected by pH values. Actinobacteria and Gammaproteobacteria were abundant in samples characterized by low pH values, while Nitrospirae, Chloroflexi, Deltaproteobacteria, Thaumarchaeota and Euryarchaeota were associated with high concentrations of heavy metals. Otherwise, Alphaproteobacteria was present in samples taken in sunlit areas. Regarding eukaryotic community structure, the sunlight had the greatest impact. Inside the mine, in the absence of light, fungi and protists members were the most abundant microorganisms, while those samples taken in the presence of light displayed algae (green algae and diatoms) as the most abundant ones. After receiving the mine drainage, the stream showed a decrease in the diatom abundance and green algae predominated.

Vertical Displacement of the Surface Area over the Leakage to the Transverse salt Mine in 1992-2012

NASA Astrophysics Data System (ADS)

Lipecki, Tomasz

2018-03-01

The leakage of water in the salt mine caused considerable deformation of the surface. This article shows the vertical displacement in the area of leakage to the mine excavation, measured by precision leveling, carried out from the first days of leakage in 1992 until 2012. The geological and hydrogeological conditions of the mine, as well as the associated water hazards were described, which in conjunction with the inconvenient location of the excavation site in the northern frontage of the Carpathians and also inadequately conducted mining operations, contributed to the risk of flooding mine. The analysis of the vertical movements of the surface - subsidence and uplift - were present as well as the process of formation of the depression trough in the form of maps and graphs. The analyzes were based on 49 measurement series, starting from the first days of the disaster within the next 20 years. The course of development of the depression trough and the condition of the surface after stopping the water from the rock mass has been shown, which caused the surface to uplift.

Modelling of Longwall Mining-Induced Strata Permeability Change

NASA Astrophysics Data System (ADS)

Adhikary, D. P.; Guo, H.

2015-01-01

The field measurement of permeability within the strata affected by mining is a challenging and expensive task, thus such tests may not be carried out in large numbers to cover all the overburden strata and coal seams being affected by mining. However, numerical modelling in conjunction with a limited number of targeted field measurements can be used efficiently in assessing the impact of mining on a regional scale. This paper presents the results of underground packer testing undertaken at a mine site in New South Wales in Australia and numerical simulations conducted to assess the mining-induced strata permeability change. The underground packer test results indicated that the drivage of main headings (roadways) had induced a significant change in permeability into the solid coal barrier. Permeability increased by more than 50 times at a distance of 11.2-11.5 m from the roadway rib into the solid coal barrier. The tests conducted in the roof strata above the longwall goaf indicated more than 1,000-fold increase in permeability. The measured permeability values varied widely and strangely on a number of occasions; for example the test conducted from the main headings at the 8.2-8.5 m test section in the solid coal barrier showed a decline in permeability value as compared to that at the 11.2-11.5 m section contrary to the expectations. It is envisaged that a number of factors during the tests might have had affected the measured values of permeability: (a) swelling and smearing of the borehole, possibly lowering the permeability values; (b) packer bypass by larger fractures; (c) test section lying in small but intact (without fractures) rock segment, possibly resulting in lower permeability values; and (d) test section lying right at the extensive fractures, possibly measuring higher permeability values. Once the anomalous measurement data were discarded, the numerical model results could be seen to match the remaining field permeability measurement data reasonably well.

Identifying Catchment-Scale Predictors of Coal Mining Impacts on New Zealand Stream Communities.

PubMed

Clapcott, Joanne E; Goodwin, Eric O; Harding, Jon S

2016-03-01

Coal mining activities can have severe and long-term impacts on freshwater ecosystems. At the individual stream scale, these impacts have been well studied; however, few attempts have been made to determine the predictors of mine impacts at a regional scale. We investigated whether catchment-scale measures of mining impacts could be used to predict biological responses. We collated data from multiple studies and analyzed algae, benthic invertebrate, and fish community data from 186 stream sites, including un-mined streams, and those associated with 620 mines on the West Coast of the South Island, New Zealand. Algal, invertebrate, and fish richness responded to mine impacts and were significantly higher in un-mined compared to mine-impacted streams. Changes in community composition toward more acid- and metal-tolerant species were evident for algae and invertebrates, whereas changes in fish communities were significant and driven by a loss of nonmigratory native species. Consistent catchment-scale predictors of mining activities affecting biota included the time post mining (years), mining density (the number of mines upstream per catchment area), and mining intensity (tons of coal production per catchment area). Mining was associated with a decline in stream biodiversity irrespective of catchment size, and recovery was not evident until at least 30 years after mining activities have ceased. These catchment-scale predictors can provide managers and regulators with practical metrics to focus on management and remediation decisions.

Identifying Catchment-Scale Predictors of Coal Mining Impacts on New Zealand Stream Communities

NASA Astrophysics Data System (ADS)

Clapcott, Joanne E.; Goodwin, Eric O.; Harding, Jon S.

2016-03-01

Coal mining activities can have severe and long-term impacts on freshwater ecosystems. At the individual stream scale, these impacts have been well studied; however, few attempts have been made to determine the predictors of mine impacts at a regional scale. We investigated whether catchment-scale measures of mining impacts could be used to predict biological responses. We collated data from multiple studies and analyzed algae, benthic invertebrate, and fish community data from 186 stream sites, including un-mined streams, and those associated with 620 mines on the West Coast of the South Island, New Zealand. Algal, invertebrate, and fish richness responded to mine impacts and were significantly higher in un-mined compared to mine-impacted streams. Changes in community composition toward more acid- and metal-tolerant species were evident for algae and invertebrates, whereas changes in fish communities were significant and driven by a loss of nonmigratory native species. Consistent catchment-scale predictors of mining activities affecting biota included the time post mining (years), mining density (the number of mines upstream per catchment area), and mining intensity (tons of coal production per catchment area). Mining was associated with a decline in stream biodiversity irrespective of catchment size, and recovery was not evident until at least 30 years after mining activities have ceased. These catchment-scale predictors can provide managers and regulators with practical metrics to focus on management and remediation decisions.

Questa Baseline and Pre-Mining Ground-Water Quality Investigation. 25. Summary of Results and Baseline and Pre-Mining Ground-Water Geochemistry, Red River Valley, Taos County, New Mexico, 2001-2005

USGS Publications Warehouse

Nordstrom, D. Kirk

2008-01-01

Active and inactive mine sites are challenging to remediate because of their complexity and scale. Regulations meant to achieve environmental restoration at mine sites are equally challenging to apply for the same reasons. The goal of environmental restoration should be to restore contaminated mine sites, as closely as possible, to pre-mining conditions. Metalliferous mine sites in the Western United States are commonly located in hydrothermally altered and mineralized terrain in which pre-mining concentrations of metals were already anomalously high. Typically, those pre-mining concentrations were not measured, but sometimes they can be reconstructed using scientific inference. Molycorp?s Questa molybdenum mine in the Red River Valley, northern New Mexico, is located near the margin of the Questa caldera in a highly mineralized region. The State of New Mexico requires that ground-water quality standards be met on closure unless it can be shown that potential contaminant concentrations were higher than the standards before mining. No ground water at the mine site had been chemically analyzed before mining. The aim of this investigation, in cooperation with the New Mexico Environment Department (NMED), is to infer the pre-mining ground-water quality by an examination of the geologic, hydrologic, and geochemical controls on ground-water quality in a nearby, or proximal, analog site in the Straight Creek drainage basin. Twenty-seven reports contain details of investigations on the geological, hydrological, and geochemical characteristics of the Red River Valley that are summarized in this report. These studies include mapping of surface mineralogy by Airborne Visible-Infrared Imaging Spectrometry (AVIRIS); compilations of historical surface- and ground- water quality data; synoptic/tracer studies with mass loading and temporal water-quality trends of the Red River; reaction-transport modeling of the Red River; environmental geology of the Red River Valley; lake-sediment chemistry; geomorphology and its effect on ground-water flow; geophysical studies on depth to ground-water table and depth to bedrock; bedrock fractures and their potential influence on ground-water flow; leaching studies of scars and waste-rock piles; mineralogy and mineral chemistry and their effect on ground-water quality; debris-flow hazards; hydrology and water balance for the Red River Valley; ground-water geochemistry of selected wells undisturbed by mining in the Red River Valley; and quality assurance and quality control of water analyses. Studies aimed specifically at the Straight Creek natural-analog site include electrical surveys; high-resolution seismic survey; age-dating with tritium/helium; water budget; ground-water hydrology and geochemistry; and comparison of mineralogy and lithology to that of the mine site. The highly mineralized and hydrothermally altered volcanic rocks of the Red River Valley contain several percent pyrite in the quartz-sericite-pyrite (QSP) alteration zone, which weather naturally to acid-sulfate surface and ground waters that discharge to the Red River. Weathering of waste-rock piles containing pyrite also contributes acid water that eventually discharges into the Red River. These acid discharges are neutralized by circumneutral-pH, carbonate-buffered surface and ground waters of the Red River. The buffering capacity of the Red River, however, decreases from the town of Red River to the U.S. Geological Survey (USGS) gaging station near Questa. During short, but intense, storm events, the buffering capacity is exceeded and the river becomes acid from the rapid flushing of acidic materials from natural scar areas. The lithology, mineralogy, elevation, and hydrology of the Straight Creek proximal analog site were found to closely approximate those of the mine site with the exception of the mine site?s Sulphur Gulch catchment. Sulphur Gulch contains three subcatchments?upper Sulphur Gulch, Blind Gulch, and Spring Gulc

Robust statistical methods for impulse noise suppressing of spread spectrum induced polarization data, with application to a mine site, Gansu province, China

NASA Astrophysics Data System (ADS)

Liu, Weiqiang; Chen, Rujun; Cai, Hongzhu; Luo, Weibin

2016-12-01

In this paper, we investigated the robust processing of noisy spread spectrum induced polarization (SSIP) data. SSIP is a new frequency domain induced polarization method that transmits pseudo-random m-sequence as source current where m-sequence is a broadband signal. The potential information at multiple frequencies can be obtained through measurement. Removing the noise is a crucial problem for SSIP data processing. Considering that if the ordinary mean stack and digital filter are not capable of reducing the impulse noise effectively in SSIP data processing, the impact of impulse noise will remain in the complex resistivity spectrum that will affect the interpretation of profile anomalies. We implemented a robust statistical method to SSIP data processing. The robust least-squares regression is used to fit and remove the linear trend from the original data before stacking. The robust M estimate is used to stack the data of all periods. The robust smooth filter is used to suppress the residual noise for data after stacking. For robust statistical scheme, the most appropriate influence function and iterative algorithm are chosen by testing the simulated data to suppress the outliers' influence. We tested the benefits of the robust SSIP data processing using examples of SSIP data recorded in a test site beside a mine in Gansu province, China.

Exposure to dust and particle-associated 1-nitropyrene of drivers of diesel-powered equipment in underground mining.

PubMed

Scheepers, P T J; Micka, V; Muzyka, V; Anzion, R; Dahmann, D; Poole, J; Bos, R P

2003-07-01

A field study was conducted in two mines in order to determine the most suitable strategy for ambient exposure assessment in the framework of a European study aimed at validation of biological monitoring approaches for diesel exhaust (BIOMODEM). Exposure to dust and particle-associated 1-nitropyrene (1-NP) was studied in 20 miners of black coal by the long wall method (Czech Republic) and in 20 workers in oil shale mining by the room and pillar method (Estonia). The study in the oil shale mine was extended to include 100 workers in a second phase (main study). In each mine half of the study population worked underground as drivers of diesel-powered trains (black coal) and excavators (oil shale). The other half consisted of workers occupied in various non-diesel production assignments. Exposure to diesel exhaust was studied by measurement of inhalable and respirable dust at fixed locations and by personal air sampling of respirable dust. The ratio of geometric mean inhalable to respirable dust concentration was approximately two to one. The underground/surface ratio of respirable dust concentrations measured at fixed locations and in the breathing zones of the workers was 2-fold or greater. Respirable dust was 2- to 3-fold higher in the breathing zone than at fixed sampling locations. The 1-NP content in these dust fractions was determined by gas chromatography-mass spectrometry/mass spectrometry and ranged from 0.003 to 42.2 ng/m(3) in the breathing zones of the workers. In mine dust no 1-NP was detected. In both mines 1-NP was observed to be primarily associated with respirable particles. The 1-NP concentrations were also higher underground than on the surface (2- to 3-fold in the coal mine and 10-fold or more in the oil shale mine). Concentrations of 1-NP in the breathing zones were also higher than at fixed sites (2.5-fold in the coal mine and 10-fold in the oil shale mine). For individual exposure assessment personal air sampling is preferred over air sampling at fixed sites. This study also suggests that particle-associated 1-NP much better reflects the ambient exposure to diesel exhaust particles than dust concentrations. Therefore, measurement of particle-associated 1-NP is preferred over measurement of dust concentrations by gravimetry, when linking ambient exposure to biomonitoring outcomes such as protein and DNA adducts and excretion of urinary metabolites of genotoxic substances.

Monitoring Metal Pollution Levels in Mine Wastes around a Coal Mine Site Using GIS

NASA Astrophysics Data System (ADS)

Sanliyuksel Yucel, D.; Yucel, M. A.; Ileri, B.

2017-11-01

In this case study, metal pollution levels in mine wastes at a coal mine site in Etili coal mine (Can coal basin, NW Turkey) are evaluated using geographical information system (GIS) tools. Etili coal mine was operated since the 1980s as an open pit. Acid mine drainage is the main environmental problem around the coal mine. The main environmental contamination source is mine wastes stored around the mine site. Mine wastes were dumped over an extensive area along the riverbeds, and are now abandoned. Mine waste samples were homogenously taken at 10 locations within the sampling area of 102.33 ha. The paste pH and electrical conductivity values of mine wastes ranged from 2.87 to 4.17 and 432 to 2430 μS/cm, respectively. Maximum Al, Fe, Mn, Pb, Zn and Ni concentrations of wastes were measured as 109300, 70600, 309.86, 115.2, 38 and 5.3 mg/kg, respectively. The Al, Fe and Pb concentrations of mine wastes are higher than world surface rock average values. The geochemical analysis results from the study area were presented in the form of maps. The GIS based environmental database will serve as a reference study for our future work.

Waste heat generation: A comprehensive review.

PubMed

Yeşiller, Nazli; Hanson, James L; Yee, Emma H

2015-08-01

A comprehensive review of heat generation in various types of wastes and of the thermal regime of waste containment facilities is provided in this paper. Municipal solid waste (MSW), MSW incineration ash, and mining wastes were included in the analysis. Spatial and temporal variations of waste temperatures, thermal gradients, thermal properties of wastes, average temperature differentials, and heat generation values are provided. Heat generation was influenced by climatic conditions, mean annual earth temperatures, waste temperatures at the time of placement, cover conditions, and inherent heat generation potential of the specific wastes. Time to onset of heat generation varied between months and years, whereas timelines for overall duration of heat generation varied between years and decades. For MSW, measured waste temperatures were as high as 60-90°C and as low as -6°C. MSW incinerator ash temperatures varied between 5 and 87°C. Mining waste temperatures were in the range of -25 to 65°C. In the wastes analyzed, upward heat flow toward the surface was more prominent than downward heat flow toward the subsurface. Thermal gradients generally were higher for MSW and incinerator ash and lower for mining waste. Based on thermal properties, MSW had insulative qualities (low thermal conductivity), while mining wastes typically were relatively conductive (high thermal conductivity) with ash having intermediate qualities. Heat generation values ranged from -8.6 to 83.1MJ/m(3) and from 0.6 to 72.6MJ/m(3) for MSW and mining waste, respectively and was 72.6MJ/m(3) for ash waste. Conductive thermal losses were determined to range from 13 to 1111MJ/m(3)yr. The data and analysis provided in this review paper can be used in the investigation of heat generation and thermal regime of a wide range of wastes and waste containment facilities located in different climatic regions. Copyright © 2015 Elsevier Ltd. All rights reserved.

A study of mining-induced seismicity in Czech mines with longwall coal exploitation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holub, K.

2007-01-15

A review is performed for the data of local and regional seismographical networks installed in mines of the Ostrava-Karvina Coal Basin (Czech Republic), where underground anthracite mining is carried out and dynamic events occur in the form of rockbursts. The seismological and seismoacoustic observations data obtained in panels that are in limiting state are analyzed. This aggregate information is a basic for determining hazardous zones and assigning rockburst prevention measures.

The dendroanalysis of oak trees as a method of biomonitoring past and recent contamination in an area influenced by uranium mining.

PubMed

Märten, Arno; Berger, Dietrich; Köhler, Mirko; Merten, Dirk

2015-12-01

We reconstructed the contamination history of an area influenced by 40 years of uranium mining and subsequent remediation actions using dendroanalysis (i.e., the determination of the elemental content of tree rings). The uranium content in the tree rings of four individual oak trees (Quercus sp.) was determined by laser ablation with inductively coupled plasma mass spectrometry (LA-ICP-MS). This technique allows the investigation of trace metals in solid samples with a spatial resolution of 250 μm and a detection limit below 0.01 μg/g for uranium. The investigations show that in three of the four oaks sampled, there were temporally similar uranium concentrations. These were approximately 2 orders of magnitude higher (0.15 to 0.4 μg/g) than those from before the period of active mining (concentrations below 0.01 μg/g). After the mining was terminated and the area was restored, the uranium contents in the wood decreased by approximately 1 order of magnitude. The similar radial uranium distribution patterns of the three trees were confirmed by correlation analysis. In combination with the results of soil analyses, it was determined that there was a heterogeneous contamination in the forest investigated. This could be confirmed by pre-remediation soil uranium contents from literature. The uranium contents in the tree rings of the oaks investigated reflect the contamination history of the study area. This study demonstrates that the dendrochemical analysis of oak tree rings is a suitable technique for investigating past and recent uranium contamination in mining areas.

Laboratory measurements of electric properties of composite mine dump samples from Colorado and New Mexico

USGS Publications Warehouse

Anderson, Anita L.; Campbell, David L.; Beanland, Shay

2001-01-01

Individual mine waste samples were collected and combined to form one composite sample at each of eight mine dump sites in Colorado and New Mexico. The samples were air-dried and sieved to determine the geochemical composition of their <2mm size fraction. Splits of the samples were then rehydrated and their electrical properties were measured in the US Geological Survey Petrophysical Laboratory, Denver, Colorado (PetLab). The PetLab measurements were done twice: in 1999, using convenient amounts of rehydration water ranging from 5% to 8%; and in 2000, using carefully controlled rehydrations to 5% and 10% water. This report gives geochemical analyses of the <2mm size fraction of the composite samples (Appendix A), PetLab graphs of the 1999 measurements (Appendix B), Petlab graphs of the 2000 measurements (Appendix C), and Cole-Cole models of the PetLab data from the 2000 measurements (Appendix D).

Geochemical investigations by the U.S. Geological Survey on uranium mining, milling, and environmental restoration

USGS Publications Warehouse

Landa, Edward R.; Cravotta, Charles A.; Naftz, David L.; Verplanck, Philip L.; Nordstrom, D. Kirk; Zielinski, Robert A.

2000-01-01

Recent research by the U.S. Geological Survey has characterized contaminant sources and identified important geochemical processes that influence transport of radionuclides from uranium mining and milling wastes. 1) Selective extraction studies indicated that alkaline earth sulfates and hydrous ferric oxides are important hosts of 226Ra in uranium mill tailings. The action of sulfate-reducing and ironreducing bacteria on these phases was shown to enhance release of radium, and this adverse result may temper decisions to dispose of uranium mill tailings in anaerobic environments. 2) Field studies have shown that although surface-applied sewage sludge/wood chip amendments aid in revegetating pyritic spoil, the nitrogen in sludge leachate can enhance pyrite oxidation, acidification of groundwater, and the consequent mobilization of metals and radionuclides. 3) In a U.S. Environmental Protection Agencyfunded study, three permeable reactive barriers consisting of phosphate-rich material, zero-valent iron, or amorphous ferric oxyhydroxide have been installed at an abandoned uranium upgrader facility near Fry Canyon, UT. Preliminary results indicate that each of the permeable reactive barriers is removing the majority of the uranium from the groundwater. 4) Studies on the geochemistry of rare earth elements as analogues for actinides such as uranium and thorium in acid mine drainage environments indicate high mobility under acid-weathering conditions but measurable attenuation associated with iron and aluminum colloid formation. Mass balances from field and laboratory studies are being used to quantify the amount of attenuation. 5) A field study in Colorado demonstrated the use of 234U/238U isotopic ratio measurements to evaluate contamination of shallow groundwater with uranium mill effluent.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kirby, Carolyn L; Lord, Anna C. Snider

The Bryan Mound caprock was subjected to extens ive sulphur mining prior to the development of the Strategic Petroleum Reserve. Undoubtedl y, the mining has modified the caprock integrity. Cavern wells at Bryan Mound have been subject to a host of well integr ity concerns with many likely compromised by the cavernous capro ck, surrounding corrosive environment (H 2 SO 4 ), and associated elevated residual temperatures al l of which are a product of the mining activities. The intent of this study was to understand the sulphur mining process and how the mining has affected the stability of themore » caprock and how the compromised caprock has influenced the integrity of the cavern wells. After an extensiv e search to collect pert inent information through state agencies, literature sear ches, and the Sandia SPR librar y, a better understanding of the caprock can be inferred from the knowledge gaine d. Specifically, the discovery of the original ore reserve map goes a long way towards modeling caprock stability. In addition the gained knowledge of sulphur mining - subs idence, superheated corrosive wa ters, and caprock collapse - helps to better predict the post mi ning effects on wellbore integrity. This page intentionally left blank« less

The N-Terminal Amphipathic Helix of the Topological Specificity Factor MinE Is Associated with Shaping Membrane Curvature

PubMed Central

Shih, Yu-Ling; Huang, Kai-Fa; Lai, Hsin-Mei; Liao, Jiahn-Haur; Lee, Chai-Siah; Chang, Chiao-Min; Mak, Huey-Ming; Hsieh, Cheng-Wei; Lin, Chu-Chi

2011-01-01

Pole-to-pole oscillations of the Min proteins in Escherichia coli are required for the proper placement of the division septum. Direct interaction of MinE with the cell membrane is critical for the dynamic behavior of the Min system. In vitro, this MinE-membrane interaction led to membrane deformation; however, the underlying mechanism remained unclear. Here we report that MinE-induced membrane deformation involves the formation of an amphipathic helix of MinE2–9, which, together with the adjacent basic residues, function as membrane anchors. Biochemical evidence suggested that the membrane association induces formation of the helix, with the helical face, consisting of A2, L3, and F6, inserted into the membrane. Insertion of this helix into the cell membrane can influence local membrane curvature and lead to drastic changes in membrane topology. Accordingly, MinE showed characteristic features of protein-induced membrane tubulation and lipid clustering in in vitro reconstituted systems. In conclusion, MinE shares common protein signatures with a group of membrane trafficking proteins in eukaryotic cells. These MinE signatures appear to affect membrane curvature. PMID:21738659

Ten million tragedies, one step at a time

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wurst, J.

Lacking the drama of nuclear weapons, ballistic missiles, or handguns, land mines have generally escaped professional and public attention. As land mines begin to be perceived as obstacles to post-war peacebuilding, some humanitarian groups and a few governments are preparing to fight the production and distribution of these weapons. Last year, a coalition of humanitarian groups including Human Rights Watch, Handicap International, Physicians for Human Rights, and the Vietman Veterans of America Foundation (VVAF) launched an international campaign to ban the production and sale of mines; the United Nations began exploring its options, and some governments called for strengthening anmore » existing convention that was designed to control mines. This article describes the types of land mines and ways in which they are used, estimates some numbers of people injured by land mines in various conflicts, and discusses the market for land mines. Measures for exposing the land mine business and for clearing existing mines are discussed.« less

Tools of Realization of Social Responsibility of Industrial Business for Sustainable Socio-economic Development of Mining Region's Rural Territory

NASA Astrophysics Data System (ADS)

Jurzina, Tatyana; Egorova, Natalia; Zaruba, Natalia; Kosinskij, Peter

2017-11-01

Modern conditions of the Russian economy do especially relevant questions of social responsibility of industrial business of the mining region for sustainable social and economic development of rural territories that demands search of the new strategy, tools, ways for positioning and increase in competitiveness of the enterprises, which are carrying out the entrepreneurial activity in this territory. The article opens problems of an influence of the industrial enterprises on the territory of presence, reasons the theoretical base directed to the formation of practical tools (mechanism) providing realization of social responsibility of business for sustainable social and economic development of rural territories of the mining region.

Exposure to whole-body vibration in open-cast mines in the Barents region.

PubMed

Burström, Lage; Hyvärinen, Ville; Johnsen, Magnar; Pettersson, Hans

2016-01-01

We aimed to measure and evaluate whole-body vibration (WBV) exposure among drivers of mining vehicles in the Barents region. In the period from November 2012 to August 2014, this cross-sectional study was carried out at 3 mines in Finland, Norway and Sweden as part of the MineHealth project. Measurements of WBV were conducted on the surface of the driver's seat during normal work in accordance with international standards. Personal data on daily exposure times were collected by a questionnaire. Measurements were conducted on 95 different mining vehicles both as root mean square (RMS) value and vibration dose value (VDV) representing different manufacturers, models and capacities. Of the 453 miners who answered the questionnaire, 232 indicated that they were exposed to WBV during their working day. The results show that the mean daily exposure time varies between 1.9 and 6.7 h for different vehicles. The calculated mean A(8) could be found in an interval between 0.2 and 1.0 m/s(2) and the corresponding 8-h VDV fell between 7 and 17 m/s(1.75). Exposure to WBV among operators of mining vehicles may be a serious health and safety problem in the mines studied. The employers ought, therefore, take active steps to reduce exposure in accordance with the European vibration directive. Moreover, since some groups of drivers are exposed to vibration that is close to or exceeds the exposure limit values, the employer should take immediate action to reduce exposure below these values.

Exposure to whole-body vibration in open-cast mines in the Barents region

PubMed Central

Burström, Lage; Hyvärinen, Ville; Johnsen, Magnar; Pettersson, Hans

2016-01-01

Objectives We aimed to measure and evaluate whole-body vibration (WBV) exposure among drivers of mining vehicles in the Barents region. Study design In the period from November 2012 to August 2014, this cross-sectional study was carried out at 3 mines in Finland, Norway and Sweden as part of the MineHealth project. Methods Measurements of WBV were conducted on the surface of the driver's seat during normal work in accordance with international standards. Personal data on daily exposure times were collected by a questionnaire. Results Measurements were conducted on 95 different mining vehicles both as root mean square (RMS) value and vibration dose value (VDV) representing different manufacturers, models and capacities. Of the 453 miners who answered the questionnaire, 232 indicated that they were exposed to WBV during their working day. The results show that the mean daily exposure time varies between 1.9 and 6.7 h for different vehicles. The calculated mean A(8) could be found in an interval between 0.2 and 1.0 m/s2 and the corresponding 8-h VDV fell between 7 and 17 m/s1.75. Conclusions Exposure to WBV among operators of mining vehicles may be a serious health and safety problem in the mines studied. The employers ought, therefore, take active steps to reduce exposure in accordance with the European vibration directive. Moreover, since some groups of drivers are exposed to vibration that is close to or exceeds the exposure limit values, the employer should take immediate action to reduce exposure below these values. PMID:26864832

Using temporarily coherent point interferometric synthetic aperture radar for land subsidence monitoring in a mining region of western China

NASA Astrophysics Data System (ADS)

Fan, Hongdong; Xu, Qiang; Hu, Zhongbo; Du, Sen

2017-04-01

Yuyang mine is located in the semiarid western region of China where, due to serious land subsidence caused by underground coal exploitation, the local ecological environment has become more fragile. An advanced interferometric synthetic aperture radar (InSAR) technique, temporarily coherent point InSAR, is applied to measure surface movements caused by different mining conditions. Fifteen high-resolution TerraSAR-X images acquired between October 2, 2012, and March 27, 2013, were processed to generate time-series data for ground deformation. The results show that the maximum accumulated values of subsidence and velocity were 86 mm and 162 mm/year, respectively; these measurements were taken above the fully mechanized longwall caving faces. Based on the dynamic land subsidence caused by the exploitation of one working face, the land subsidence range was deduced to have increased 38 m in the mining direction with 11 days' coal extraction. Although some mining faces were ceased in 2009, they could also have contributed to a small residual deformation of overlying strata. Surface subsidence of the backfill mining region was quite small, the maximum only 21 mm, so backfill exploitation is an effective method for reducing the land subsidence while coal is mined.

Interestingness measures and strategies for mining multi-ontology multi-level association rules from gene ontology annotations for the discovery of new GO relationships.

PubMed

Manda, Prashanti; McCarthy, Fiona; Bridges, Susan M

2013-10-01

The Gene Ontology (GO), a set of three sub-ontologies, is one of the most popular bio-ontologies used for describing gene product characteristics. GO annotation data containing terms from multiple sub-ontologies and at different levels in the ontologies is an important source of implicit relationships between terms from the three sub-ontologies. Data mining techniques such as association rule mining that are tailored to mine from multiple ontologies at multiple levels of abstraction are required for effective knowledge discovery from GO annotation data. We present a data mining approach, Multi-ontology data mining at All Levels (MOAL) that uses the structure and relationships of the GO to mine multi-ontology multi-level association rules. We introduce two interestingness measures: Multi-ontology Support (MOSupport) and Multi-ontology Confidence (MOConfidence) customized to evaluate multi-ontology multi-level association rules. We also describe a variety of post-processing strategies for pruning uninteresting rules. We use publicly available GO annotation data to demonstrate our methods with respect to two applications (1) the discovery of co-annotation suggestions and (2) the discovery of new cross-ontology relationships. Copyright © 2013 The Authors. Published by Elsevier Inc. All rights reserved.

Salt dissolution sinkhole at the Weeks Island, Louisiana, Strategic Petroleum Reserve storage site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neal, J.T.; Myers, R.E.

1994-12-31

A sinkhole was first observed in May 1992 over the outer edge of the two-tiered former salt mine that was converted for oil storage by the US Strategic Petroleum Reserve (SPR). Results of diagnostic studies which included geophysical, geochemical, drilling, and hydrological methods suggest a direct connection exists between the surface collapse area and the underground mine. The connection was confirmed by correlative measurements of sediment slump rates, piezometric surface deflection, and brine influx rates into the mine. The dissolution of salt below the sinkhole that initiated the leak into the mine was likely caused by several confluent geologic processes,more » and exacerbated by mining-induced stresses that created fractures which severed as hydrologic flowpaths. Modeling studies of mine stresses show that years of tensional stresses may be required before cracking begins to occur, but once begun can continue to develop, and relieve the stress in that specific regime. The crack regime creates the avenue for incursion of groundwater, very slowly initially, but gradually enlarging as undersaturated groundwater dissolves salt on the sides of the crack. Mitigative measures include increasing the mine pressurization, slowing the dissolution by injecting brine into the sinkhole throat, and permeation grouting in hydrologic flowpaths.« less

Use of morphometric soil aggregates parameters to evaluate the reclamation process in mined areas located at amazon forest - Brazil

NASA Astrophysics Data System (ADS)

Ribeiro, A. I.; Fengler, F. H.; Longo, R. M.; Mello, G. F.; Damame, D. B.; Crowley, D. E.

2015-12-01

Brazil has a high mineral potential that have been explored over the years. A large fraction of these mineral resources are located in Amazon region, which is known for its large biodiversity and world climate importance. As the policies that control the Amazon preservation are relatively new, several mining activities have been exploring the Amazon territory, promoting a large process of degradation. Once the mining activities have a high potential of environmental changes the government created polices to restrain the mining in Amazon forests and obligate mining companies to reclaim theirs minded areas. However, the measurement of reclamation development still is a challenging task for the Professionals involved. The volume and complexity of the variables, allied to the difficulty in identifying the reclamation of ecosystem functionalities are still lack to ensure the reclamation success. In this sense this work aims to investigate the representativeness of morphometric soil aggregates parameters in the understanding of reclamation development. The study area is located in the National Forest of Jamari, State of Rondônia. In the past mining companies explored the region producing eight closed mines that are now in reclamation process. The soil aggregates morphometric measurements: geometric mean diameter (GMD), aggregate circularity index, and aggregate roundness, were choose based in its obtaining facility, and their association to biological activity. To achieve the proposed objective the aggregates of eight sites in reclamation, from different closed mines, where chosen and compared to Amazon forest and open mine soil aggregates. The results were analyzed to one way ANOVA to identifying differences between areas in reclamation, natural ecosystem, and open mine. It was obtained differences for GMD and circularity index. However, only the circularity index allowed to identifying differences between the reclamation sites. The results allowed concluding: (1) Morphometric aggregates measurements can represent the reclamation process in Amazon territory; (2) To validate the results more areas in reclamation process in different ecosystems must be investigated; (3) Roundness didn't represented any differences.Key words: circularity index, ecosystem, geometric mean diameter.

A semantic model for multimodal data mining in healthcare information systems.

PubMed

Iakovidis, Dimitris; Smailis, Christos

2012-01-01

Electronic health records (EHRs) are representative examples of multimodal/multisource data collections; including measurements, images and free texts. The diversity of such information sources and the increasing amounts of medical data produced by healthcare institutes annually, pose significant challenges in data mining. In this paper we present a novel semantic model that describes knowledge extracted from the lowest-level of a data mining process, where information is represented by multiple features i.e. measurements or numerical descriptors extracted from measurements, images, texts or other medical data, forming multidimensional feature spaces. Knowledge collected by manual annotation or extracted by unsupervised data mining from one or more feature spaces is modeled through generalized qualitative spatial semantics. This model enables a unified representation of knowledge across multimodal data repositories. It contributes to bridging the semantic gap, by enabling direct links between low-level features and higher-level concepts e.g. describing body parts, anatomies and pathological findings. The proposed model has been developed in web ontology language based on description logics (OWL-DL) and can be applied to a variety of data mining tasks in medical informatics. It utility is demonstrated for automatic annotation of medical data.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solc, J.

The reclamation effort typically deals with consequences of mining activity instead of being planned well before the mining. Detailed assessment of principal hydro- and geochemical processes participating in pore and groundwater chemistry evolution was carried out at three surface mine localities in North Dakota-the Fritz mine, the Indian Head mine, and the Velva mine. The geochemical model MINTEQUA2 and advanced statistical analysis coupled with traditional interpretive techniques were used to determine site-specific environmental characteristics and to compare the differences between study sites. Multivariate statistical analysis indicates that sulfate, magnesium, calcium, the gypsum saturation index, and sodium contribute the most tomore » overall differences in groundwater chemistry between study sites. Soil paste extract pH and EC measurements performed on over 3700 samples document extremely acidic soils at the Fritz mine. The number of samples with pH <5.5 reaches 80%-90% of total samples from discrete depth near the top of the soil profile at the Fritz mine. Soil samples from Indian Head and Velva do not indicate the acidity below the pH of 5.5 limit. The percentage of samples with EC > 3 mS cm{sup -1} is between 20% and 40% at the Fritz mine and below 20% for samples from Indian Head and Velva. The results of geochemical modeling indicate an increased tendency for gypsum saturation within the vadose zone, particularly within the lands disturbed by mining activity. This trend is directly associated with increased concentrations of sulfate anions as a result of mineral oxidation. Geochemical modeling, statistical analysis, and soil extract pH and EC measurements proved to be reliable, fast, and relatively cost-effective tools for the assessment of soil acidity, the extent of the oxidation zone, and the potential for negative impact on pore and groundwater chemistry.« less

The As removal from arsenopyrite-bearing mine waste by microwave

NASA Astrophysics Data System (ADS)

Kim, Hyun Soo; Myung, Eun Ji; Hack Lim, Dae; Kim, Bong Ju; Park, Cheon Young

2016-04-01

Penalties incurred by miners for arsenic in concentrates have increased significantly because the removal and disposal of arsenic is difficult and costly for smelters and because the environmental challenges are increasing worldwide. Typically miners incur penalties on arsenic in concentrates above 0.2% As with smelter rejection limits of 0.5%. Therefore, finding an effective solution for removing As during primary mining activities is necessary to avoid penalty. The aim of this study was to investigate the As removal from mine waste using microwave process. The mine waste samples were characterized by chemical and XRD analysis. To determine of As removal from the microwave experiments, aqua regia digestion was performed according to Korean environmental standard method(KESM) and the As removal effect were evaluated using the standard EPA toxicity characteristic leaching procedure(TCLP, EPA 1311 method). The result of mineralogical character for mine waste using XRD was detected arsenopyrite, pyrite, chalcopyrite, pyrrhotite and quartz. The chemical analysis of As, Pb, Zn contents in the mine waste measured 13,896.0, 896.1 and 1,054.6 mg/kg, respectively. The As removal of experiments was conducted to examine the effects of microwave exposure time(1~15min). The results showed that the As removal in mine waste (exposure time = 10min) was 92.90%, and the temperature of mine waste by microwave heating was 886℃. The TCLP leaching of treated mine waste by microwave measured values were below the EPA's current regulatory threshold(As, Pb, Zn : 5 mg/L). The optimum condition of microwave exposure for As removal from arsenopyrite-bearing mine waste was obtained at 800W, 2450MHz, 10min. Acknowledgment : This work was supported by the Energy and Resources Engineering Program Grant funded by the Ministry of Trade, Industry and Energy, Korea

Geologic and tectonic characteristics of rockbursts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adushkin, V.V.; Charlamov, V.A.; Kondratyev, S.V.

1995-06-01

The modern mining enterprises have attained such scales of engineering activity that their direct influence to a rock massif and in series of cases to the region seismic regime doesn`t provoke any doubts. Excavation and removal of large volumes of rock mass, industrial explosions and other technological factors during long time can lead to the accumulation of man-made changes in rock massifs capable to cause catastrophic consequences. The stress state changes in considerable domains of massif create dangerous concentration of stresses at large geological heterogeneities - faults localized in the mining works zone. External influence can lead in that casemore » to such phenomena as tectonic rockbursts and man-made earthquakes. The rockbursts problem in world mining practice exists for more than two hundred years. So that its actuality not only doesn`t decrease but steadily mounts up as due to the mining works depth increase, enlargement of the useful minerals excavations volumes as due to the possibility of safe use of the rock massif potential energy for facilitating the mastering of the bowels of the Earth and for making that more cheap. The purpose of present work is to study the engineering activity influence to processes occurring in the upper part of Earth crust and in particular in a rock massif. The rock massif is treated in those studies as a geophysical medium - such approach takes into account the presence of block structure of medium and the continuous exchange of energy between parts of that structure. The idea ``geophysical medium`` is applied in geophysics sufficiently wide and stresses the difference of actual Earth crust and rock massifs from the continuous media models discussed in mechanics.« less

An NCME Instructional Module on Data Mining Methods for Classification and Regression

ERIC Educational Resources Information Center

Sinharay, Sandip

2016-01-01

Data mining methods for classification and regression are becoming increasingly popular in various scientific fields. However, these methods have not been explored much in educational measurement. This module first provides a review, which should be accessible to a wide audience in education measurement, of some of these methods. The module then…

30 CFR 62.174 - Follow-up corrective measures when a standard threshold shift is detected.

Code of Federal Regulations, 2012 CFR

2012-07-01

... threshold shift is detected. 62.174 Section 62.174 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... measures when a standard threshold shift is detected. The mine operator must, within 30 calendar days of receiving evidence or confirmation of a standard threshold shift, unless a physician or audiologist...

Ecotoxicity of Mine Tailings: Unrehabilitated Versus Rehabilitated.

PubMed

Maboeta, M S; Oladipo, O G; Botha, S M

2018-05-01

Earthworms are bioindicators of soil pollution. The ecotoxicity of tailings from selected gold mines in South Africa was investigated utilizing Eisenia andrei bioassays and biomarkers. Samples were obtained from unrehabilitated, rehabilitated and naturally vegetated sites. Biomass, neutral red retention time (NRRT), survival and reproduction were assessed using standardized protocols. Earthworm biomass, NRRT and reproductive success in rehabilitated tailings (comparable to naturally vegetated site) were significantly higher (p < 0.05) than in unrehabilitated tailings. In addition, significantly lower (p < 0.05) body tissue concentrations of As, Cd, Co, Cu and Ni contents were found in the rehabilitated tailings compared to the unrehabilitated. Further, significantly lower (p < 0.05) soil Mn and Zn concentrations were obtained in unrehabilitated tailings than the rehabilitated and naturally vegetated sites. Overall, reduced ecotoxicity effects were confirmed in rehabilitated compared to unrehabilitated tailings. This suggests that rehabilitation as a post-mining restorative strategy has strong positive influence on mine tailings.

Genetic and environmental effects on morphology and asexual reproduction in the moss, Bryum bicolor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shaw, A.J.

A distinctive form of Bryum bicolor, characterized by stoutly excurrent costae and abundant asexual gemmae, occurs on heavy metal-contaminated tailings of the Conrad Hill Mine in the Piedmont of North Carolina. Plants from two mine site populations, plus two other populations from Richmond, Virginia, were grown on three types of soil in order to determine the degree to which morphological traits, including the number of gemmae per plant, can be modified by substrate. All populations grew equally well in the mine soil, and there was no evidence that plants from the mine site populations were physiologically adapted for growth onmore » the contaminated tailings. Leaf dimensions, costa length, and number of gemmae per stem were strongly influenced by substrate, although some differences between populations were maintained under experimental conditions. Populations also differed in the efficacy with which plants regenerated from gametophytic fragments.« less

Occupational health hazards of mine workers*

PubMed Central

Cho, K. S.; Lee, S. H.

1978-01-01

Mining has always been among the most hazardous of occupations, and with the increasing demand for coal and minerals safety in mines assumes even greater importance. This article describes the present situation with regard to conditions in mines, the diseases and disabilities resulting from them, and measures that can be taken to prevent or treat them. The hazards covered are: accidents, dust (including poisoning by certain ores), high temperature and humidity, noise and vibration, toxic gases, and miscellaneous other hazards. PMID:307452

The Mine Safety and Health Administration's criterion threshold value policy increases miners' risk of pneumoconiosis.

PubMed

Weeks, James L

2006-06-01

The Mine Safety and Health Administration (MSHA) proposes to issue citations for non-compliance with the exposure limit for respirable coal mine dust when measured exposure exceeds the exposure limit with a "high degree of confidence." This criterion threshold value (CTV) is derived from the sampling and analytical error of the measurement method. This policy is based on a combination of statistical and legal reasoning: the one-tailed 95% confidence limit of the sampling method, the apparent principle of due process and a standard of proof analogous to "beyond a reasonable doubt." This policy raises the effective exposure limit, it is contrary to the precautionary principle, it is not a fair sharing of the burden of uncertainty, and it employs an inappropriate standard of proof. Its own advisory committee and NIOSH have advised against this policy. For longwall mining sections, it results in a failure to issue citations for approximately 36% of the measured values that exceed the statutory exposure limit. Citations for non-compliance with the respirable dust standard should be issued for any measure exposure that exceeds the exposure limit.

Origin and influence of coal mine drainage on streams of the United States

USGS Publications Warehouse

Powell, J.D.

1988-01-01

Degradation of water quality related to oxidation of iron disulfide minerals associated with coal is a naturally occurring process that has been observed since the late seventeenth century, many years before commencement of commercial coal mining in the United States. Disturbing coal strata during mining operations accelerates this natural deterioration of water quality by exposing greater surface areas of reactive minerals to the weathering effects of the atmosphere, hydrosphere, and biosphere. Degraded water quality in the temperate eastern half of the United States is readily detected because of the low mineralization of natural water. Maps are presented showing areas in the eastern United States where concentrations of chemical constituents in water affected by coal mining (pH, dissolved sulfate, total iron, total manganese) exceed background values and indicate effects of coal mining. Areas in the East most affected by mine drainage are in western Pennsylvania, southern Ohio, western Maryland, West Virginia, southern Illinois, western Kentucky, northern Missouri, and southern Iowa. Effects of coal mining on water quality in the more arid western half of the United States are more difficult to detect because of the high degree of mineralization of natural water. Normal background concentrations of constituents are not useful in evaluating effects of coal mine drainage on streams in the more arid West. Three approaches to reduce the effects of coal mining on water quality are: (1) exclusion of oxygenated water from reactive minerals, (2) neutralization of the acid produced, (3) retardation of acid-producing bacteria population in spoil material, by application of detergents that do not produce byproducts requiring disposal. These approaches can be used to help prevent further degradation of water quality in streams by future mining. ?? 1988 Springer-Verlag New York Inc.

Environmental control on water quality; cases studies from Battle Mountain mining district, north-central Nevada. Chapter A.

USGS Publications Warehouse

Tuttle, Michele L.W.; Wanty, Richard B.; Berger, Byron R.; Stillings, Lisa L.

2003-01-01

The environmental controls on water quality were the focus of our study in a portion of the Battle Mountain mining district, north-central Nevada. Samples representing areas outside known mineralized areas, in undisturbed mineralized areas, and in mined areas were chemically and isotopically analyzed. The results are related to geologic, hydrologic, and climatic data. Streams in background areas outside the mineralized zones reflect normal weathering of volcanically derived rocks. The waters are generally dilute, slightly alkaline in pH, and very low in metals. As these streams flow into mineralized zones, their character changes. In undisturbed mineralized areas, discharge into streams of ground water through hydrologically conductive fractures can be traced with chemistry and, even more effectively, with sulfur isotopic composition of dissolved sulfate. Generally, these tracers are much more subtle than in those areas where mining has produced adits and mine-waste piles. The influence of drainage from these mining relicts on water quality is often dramatic, especially in unusually wet conditions. In one heavily mined area, we were able to show that the unusually wet weather in the winter and spring greatly degraded water quality. Addition of calcite to the acid, metalrich mine drainage raised the stream pH and nearly quantitatively removed the metals through coprecipitation and (or) adsorption onto oxyhydroxides. This paper is divided into four case studies used to demonstrate our results. Each addresses the role of geology, hydrology, mining activity and (or) local climate on water quality. Collectively, they provide a comprehensive look at the important factors affecting water quality in this portion of the Battle Mountain mining district.

[Analysis of occupational burnout and its influencing factors of colliery migrant workers in Guizhou Province].

PubMed

Zhao, Xiaodeng; Tuo, Anxie; Peng, Anhui; He, Wanjing; Zhu, Peijia; Yan, Zheng

2015-11-01

To understand the status of occupational burnout of colliery migrant workers and its influencing factors. The occupational burnout of 1161 colliery migrant workers in Jinsha County, Guizhou Province was measured with MBI-GS and the self-made questionnaire. All dimensions of MBI-GS Cronbach's α coefficient was in the range of 0.86-0.88, all 15 items of MBI-GS were subjected to factor analysis, and three latent factors were identified, which explained 68.86% of the total variance and consisted with the theory model. The score of occupational burnout of each dimension, differences in different individual characteristics (physical examination, sleep, et al) were statistically significant (P <0.05). The influence factors of occupational burnout of colliery migrant workers were physical examination, chronic disease, smoking, physical exercise, sleep, initial work in coal mine, production post and labor intensity. MBI-GS can be used to study the occupational burnout of colliery migrant workers. Different individual characteristics effect the occurrence of occupational burnout.

Stability Analysis of Railway Subgrade in Mining Area Based on Dinsar

NASA Astrophysics Data System (ADS)

Xu, J.; Hu, J.; Ding, J.

2018-04-01

DInSAR technology have been applied to monitor the mining subsidence and the stability of the railway subgrade. A total of 10 Sentinel-1A images acquired from 2015/9/26 to 2016/2/23 were used in DInSAR analysis. The study mining area is about 13.4 km2. Mining have induced serious land subsidence involve a large area that causing different levels of damages to infrastructures on the land. There is an important railway near the mining area, the DInSAR technology is applied to analyse the subsidence near the railway, which can warn early the possible deformation that may occur during underground mining. The DInSAR results was verified by the field measurement. The results show that the mining did not cause subsidence of railway subgrade and did not affect the stability of railway subgrade.

Stormflow hydrochemistry of a river draining an abandoned metal mine: the Afon Twymyn, central Wales.

PubMed

Byrne, Patrick; Reid, Ian; Wood, Paul J

2013-03-01

Contaminated drainage from metal mines is a serious water-quality problem facing nations that exploit metal mineral resources. Measurements of river hydrochemistry during baseflow are common at mine sites, whilst detailed hydrochemical information regarding stormflow is limited and often confined to a single event. This study investigates the seasonal evolution of stormflow hydrochemistry at an abandoned metal mine in central Wales, UK, and the possible sources and mechanisms of metal release. Significant flushing of metals was observed during stormflow events, resulting in concentrations that severely exceeded water-quality guidelines. The relationship between metal concentrations and river discharge suggests dissolution of efflorescent metal sulphates on the surface of the mine spoil as the principal source of the contamination. High fluxes of Pb during stormflows are linked to extended periods of dry weather prior to storm events that produced water table drawdown and encouraged oxidation of Pb sulphide in the mine spoil. However, some Pb flushing also occurred following wet antecedent conditions. It is suggested that Fe oxide reduction in mine spoil and translatory flows involving metal-rich pore waters results in flushing during wetter periods. Detailed measurements of stormflow hydrochemistry at mine sites are essential for accurate forecasting of long-term trends in metals flux to understand metal sources and mechanisms of release, to assess potential risks to water quality and instream ecology, and to gauge the potential effectiveness of remediation. In order to protect riverine and riparian ecosystems, it is suggested that routine monitoring of stormflows becomes part of catchment management in mining-impacted regions.

Research on position and orientation measurement method for roadheader based on vision/INS

NASA Astrophysics Data System (ADS)

Yang, Jinyong; Zhang, Guanqin; Huang, Zhe; Ye, Yaozhong; Ma, Bowen; Wang, Yizhong

2018-01-01

Roadheader which is a kind of special equipment for large tunnel excavation has been widely used in Coal Mine. It is one of the main mechanical-electrical equipment for mine production and also has been regarded as the core equipment for underground tunnel driving construction. With the deep application of the rapid driving system, underground tunnel driving methods with higher automation level are required. In this respect, the real-time position and orientation measurement technique for roadheader is one of the most important research contents. For solving the problem of position and orientation measurement automatically in real time for roadheaders, this paper analyses and compares the features of several existing measuring methods. Then a new method based on the combination of monocular vision and strap down inertial navigation system (SINS) would be proposed. By realizing five degree-of-freedom (DOF) measurement of real-time position and orientation of roadheader, this method has been verified by the rapid excavation equipment in Daliuta coal mine. Experiment results show that the accuracy of orientation measurement is better than 0.1°, the standard deviation of static drift is better than 0.25° and the accuracy of position measurement is better than 1cm. It is proved that this method can be used in real-time position and orientation measurement application for roadheader which has a broad prospect in coal mine engineering.

Drilling and blasting parameters in sublevel caving in Sheregesh mine

NASA Astrophysics Data System (ADS)

Eremenko, AA; Filippov, VN; Konurin, AI; Khmelinin, AP; Baryshnikov, DV; Khristolyubov, EA

2018-03-01

The factors that influence geomechanical state of rock mass in Sheregesh Mine are determined. The authors discuss a variant of geotechnology with fan drilling. The drill-hole patterns and drilling-and-blasting parameters are presented. The revealed causes of low-quality fragmentation of rocks include the presence of closed and open fractures at different distances from drill-hole mouths, both in case of rings and fans, as well as the blocking of drill-holes with rocks.

Soil management of copper mine tailing soils--sludge amendment and tree vegetation could improve biological soil quality.

PubMed

Asensio, Verónica; Covelo, Emma F; Kandeler, Ellen

2013-07-01

Mine soils at the depleted copper mine in Touro (Northwest Spain) are physico-chemically degraded and polluted by chromium and copper. To increase the quality of these soils, some areas at this mine have been vegetated with eucalyptus or pines, amended with sludges, or received both treatments. Four sites were selected at the Touro mine tailing in order to evaluate the effect of these different reclamation treatments on the biological soil quality: (1) Control (untreated), (2) Forest (vegetated), (3) Sludge (amended with sludges) and (4) Forest+Sludge (vegetated and amended). The new approach of the present work is that we evaluated the effect of planting trees or/and amending with sludges on the biological soil quality of mine sites polluted by metals under field conditions. The addition of sludges to mine sites recovered the biological quality of the soil, while vegetating with trees did not increase microbial biomass and function to the level of unpolluted sites. Moreover, amending with sludges increased the efficiency of the soil's microbial community to metabolize C and N, which was indicated by the decrease of the specific enzyme activities and the increase in the ratio Cmic:Nmic (shift towards predominance of fungi instead of bacteria). However, the high Cu and Cr concentrations still have negative influence on the microorganisms in all the treated soils. For the future remediation of mine soils, we recommend periodically adding sludge and planting native legume species. Copyright © 2013 Elsevier B.V. All rights reserved.

Source and path identification of metals pollution in a mining area by PMF and rare earth element patterns in road dust.

PubMed

Tian, Shuhan; Liang, Tao; Li, Kexin; Wang, Lingqing

2018-08-15

To better assess pollution and offer efficient protection for local residents, it is necessary to both conduct an exhaustive investigation into pollution levels and quantify its contributing sources and paths. As it is the biggest light rare earth element (REE) reserve in the world, Bayan Obo deposit releases large amounts of heavy metals into the surrounding environment. In this study, road dust from zones located at different distances to the mining area was collected and sieved using seven sizes. This allowed for subsequent analysis of size-dependent influences of mining activities. A receptor model was used to quantitatively assess mine contributions. REE distribution patterns and other REE parameters were compared with those in airborne particulates and the surrounding soil to analyze pollution paths. Results showed that 27 metals were rated as moderately to extremely polluted (2

Review of Lead-Zinc Mining Impact on Landscape in the Tri-State Mining District using Small Unmanned Aerial Vehicles.

NASA Astrophysics Data System (ADS)

Bhakta, K. D.; Yeboah-Forson, A.

2015-12-01

The Tri-State lead and zinc mining district in SW Missouri, SE Kansas, and NE Oklahoma encompasses nearly 2,500 sq. miles of land and at its peak accounted for half of the US zinc (23,000,000 tons) production that surpassed one billion dollars in economic value. Once these lead and zinc rich ores were extracted, mining and milling sites were abandoned leaving behind a new landscape with numerous environmental challenges. Since 1970, most of the sites have been targeted for remediation and reclamation by federal and state agencies including the EPA. In order to capture the full extent of the impact of lead and zinc mining in the Tri-State area, numerous geoscientific approaches including data from small unmanned aerial vehicle (UAV) were employed to investigate the influence of mining in the study area. The study presented here is focused on observational assessment of the existing landscape using multiple commercial high-definitions data from UAVs to study different sites across areas of concern in the three states. Primary results (images) gathered and analyzed DEM and GIS data from abandoned mines showed the potential to provide a quick snapshot of successful or unsuccessful remediated areas. Although research and remediation of the Tri-State mining district are a continuous process, evidence from this geomorphic study suggest that UAVs can provide a quick overview of the remediated landscape or serve as a primary background tool for a more detail site-specific environmental study.

Effect of adaptation and pulp density on bioleaching of mine waste using indigenous acidophilic bacteria

NASA Astrophysics Data System (ADS)

Cho, K.; Kim, B.; Lee, D.; Choi, N.; Park, C.

2011-12-01

Adaptation to environment is a natural phenomena that takes place in many animals, plants and microorganisms. These adapted organisms achieve stronger applicability than unadapted organisms after habitation in a specific environment for a long time. In the biohydrometallurgical industry, adaptation to special environment conditions by selective culturing is the most popular method for improving bioleaching activity of strains-although that is time consuming. This study investigated the influence of the bioleaching efficiency of mine waste under batch experimental conditions (adaptation and pulp density) using the indigenous acidophilic bacteria collected from acid mine drainage in Go-seong and Yeon-hwa, Korea. We conducted the batch experiments at the influences of parameters, such as the adaptation of bacteria and pulp density of the mine waste. In the adaptation case, the value of pH in 1'st adaptation bacteria sample exhibited lower than in 2'nd adaptation bacteria sample. And the content of both Cu and Zn at 1'st adaptation bacteria sample appeared lower than at 2'nd adaptation bacteria sample. In the SEM analysis, the rod-shaped bacteria with 1μm in length were observed on the filter paper (pore size - 0.45μm). The results of pulp density experiments revealed that the content of both Cu and Zn increased with increasing pulp density, since the increment of pulp density resulted in the enhancement of bioleaching capacity.

Assessing ecotoxicity of biomining effluents in stream ecosystems by in situ invertebrate bioassays: A case study in Talvivaara, Finland.

PubMed

Salmelin, Johanna; Leppänen, Matti T; Karjalainen, Anna K; Vuori, Kari-Matti; Gerhardt, Almut; Hämäläinen, Heikki

2017-01-01

Mining of sulfide-rich pyritic ores produces acid mine drainage waters and has induced major ecological problems in aquatic ecosystems worldwide. Biomining utilizes microbes to extract metals from the ore, and it has been suggested as a new sustainable way to produce metals. However, little is known of the potential ecotoxicological effects of biomining. In the present study, biomining impacts were assessed using survival and behavioral responses of aquatic macroinvertebrates at in situ exposures in streams. The authors used an impedance conversion technique to measure quantitatively in situ behavioral responses of larvae of the regionally common mayfly, Heptagenia dalecarlica, to discharges from the Talvivaara mine (Sotkamo, Northern Finland), which uses a biomining technique. Behavioral responses measured in 3 mine-impacted streams were compared with those measured in 3 reference streams. In addition, 3-d survival of the mayfly larvae and the oligochaete Lumbriculus variegatus was measured in the study sites. Biomining impacts on stream water quality included increased concentrations of sulfur, sulfate, and metals, especially manganese, cadmium, zinc, sodium, and calcium. Survival of the invertebrates in the short term was not affected by the mine effluents. In contrast, apparent behavioral changes in mayfly larvae were detected, but these responses were not consistent among sites, which may reflect differing natural water chemistry of the study sites. Environ Toxicol Chem 2017;36:147-155. © 2016 SETAC. © 2016 SETAC.

Exploiting Stable Mercury Isotopic Analysis to Differentiate between Mercury Sources: Gold Mining vs. Land-Use Change (Invited)

NASA Astrophysics Data System (ADS)

Bergquist, B. A.; Adler Miserendino, R. A.; Guimarães, J. R.; Veiga, M.; Velasquez-López, P.; Lees, P. S.; Thibodeau, A. M.; Fernandez, L. E.

2013-12-01

In parts of the developing world, mercury (Hg) is used to extract gold by amalgamation during artisanal and small-scale gold mining (ASGM) and this can lead to contamination of downstream aquatic ecosystems. Differentiation between Hg from ASGM and from other sources of Hg, such as increased erosion from land cover and land use change (LCLUC), is challenging and has lead to heated debates over the dominant sources of elevated Hg in some ecosystems. Here, stable Hg isotopic analysis was applied in two aquatic ecosystems in South America: (1) the Amazonian aquatic ecosystem of Amapá, Brazil downstream of artisanal gold mining (AGM) and (2) the Puyango-Tumbes River ecosystem downstream of Portovelo-Zaruma, Ecuador, a large mining area where both AGM and small-scale gold mining (SGM) are in operation. The Hg isotopic analyses from Amapá, Brazil, do not support AGM as the source of elevated Hg in the downstream aquatic ecosystem. Instead, Hg isotopes are most consistent with the elevated Hg being from preferential migration of Hg from soil erosion, which is likely associated with land use change. Although soils are regarded as Hg sinks in the global Hg cycle, this work suggests that LCLUC can disrupt Hg stores with significant ecological consequences. In contrast in the Southwestern Andean region of Ecuador and Peru, analysis of Hg isotopes and other toxic metals (i.e., Pb, Zn, Cu), which are associated with the larger scale mining and cyanide used during SGM, demonstrate Hg used during gold mining is the predominant source of Hg downstream and can be traced far from the dominant mining area. Although it has been speculated that Hg from SGM in Ecuador was not that mobile or that Hg far downstream of SGM processing plants was from erosion due to LCLUC or from AGM taking place downstream, the isotopically heavy signature of Hg used during gold mining and elevated other metal concentrations were observed ~120 km downstream of Portovelo-Zaruma. Mercury isotopes appear able to differentiate mining Hg from the non-mining background, which includes runoff from soils and atmospheric deposition, but they cannot distinguish between Hg used during mining from different mining regions or Hg used during AGM versus SGM. Thus, other toxic metals were measured that are more likely to be associated with SGM as opposed to AGM. Together, these studies demonstrate that variations in stable Hg isotopes are a viable tool to differentiate between Hg sources. Although there are unconstrained or unknown aspects of the stable Hg isotope cycle, the isotopic differences between Hg used during ASGM and from background soil, sediment and atmospheric deposition are large enough not to be obscured by changes in isotopic distributions that may be induced as Hg is transported through the environment. This is likely because most of the Hg in the above aquatic ecosystems is bound to particles and colloids and transported such that most of the Hg does not undergo transformations that fractionate Hg isotopes. For example, in the Puyango-Tumbes River, greater than 95% of the Hg is transported in the particulate phase. Thus, in areas where Hg is transported primarily in the particulate or colloidal form, it can be traced if Hg sources are isotopically distinct. Additionally, the contrasting results in our two studies show that scale and processing differences between AGM and SGM influence the extent of Hg contamination.

[Analysis and assessment of atmospheric pollution based on accumulation characterization of heavy metals in Platanus acerifolia leaves].

PubMed

Liu, Ling; Fang, Yan-Ming; Wang, Shun-Chang; Xie, Ying; Wang, Cheng-Run

2014-03-01

The present work was aimed to evaluate the heavy metal pollution in the atmosphere of Huainan City. We measured and clustered the accumulation of six heavy metals in Platanus acerifolia leaves in 20 sampling fields with six types of environmental conditions, and analyzed the EF value of heavy metal enrichment in the leaves. The results showed that the accumulations in Platanus acerifolia leaves varied according to different types of metals, following the order of Zn > Cu > Cr > Ni > Pb > Cd. Environmental conditions also had great influence on the accumulation of heavy metals. Cd and Cu were mostly found in cement plant and mine, respectively, and Cr, Ni, Pb and Zn were significant higher in main road, compared with other environmental conditions. The average values of EF for all the metals expect Cr in scenic and village area were over 1. The average values of EF for all the metals in mine, power plant, main road and cement plant were above 3. The overall pollution condition of heavy metals in Huainan City followed the order of Cd > Cu > Zn > Ni > Pb > Cr.

Jean Francheteau (1943-2010)

NASA Astrophysics Data System (ADS)

Sclater, John; Le Pichon, Xavier

2010-12-01

Jean Francheteau, pioneering marine geologist and geophysicist, AGU Fellow, and emeritus professor at the University of Brest (Université de Bretagne Occidentale), died on 21 July in St-Renan, Brittany, France, at the age of 67 after a long illness. With his passing, the field of Earth sciences lost a major contributor to the development of a definitive theory of plate tectonics and one of the first to make visual geological observations on the deep seafloor. Such scientific accomplishments, coupled with his personal charm and the ability to collaborate with researchers from many institutions, ensured that he had a huge influence not only on the world of research but also on teaching and the application of ethics to science. Jean arrived at Scripps Institution of Oceanography in La Jolla, Calif., in 1966 after obtaining a diploma in mining engineering at the prestigious Éole Nationale Supérieure de la Métallurgie et de l'Industrie des Mines in Nancy, France. He chose Victor Vacquier as his thesis supervisor and began working in Vic's lab with John Sclater, ostensibly on heat flow measurements.

A study of coal production in Nigeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akarakiri, J.B.; Afonja, A.A.; Okejiri, E.C.

The Nigerian coal industry was studied. The focus was on the problems which have caused low production output of coal. More specifically, the study examined the present techniques of coal production, the causes of low production of coal, the coal production policy as it affected this study, and proposed policy measures to address the findings. It was discovered that some of the limiting factors to coal production in Nigeria could be attributed to the lack of the following: (i) clear and specific production-demand targets set for coal in Nigeria; (ii) adequate technological capability to mechanize coal mining operations in Nigeria;more » (iii) venture capital to invest in coal production; (iv) poor infrastructural facilities for coal production such as mining, storage, transportation, etc. It was also discovered that the dissatisfaction of the miners with their conditions of service influenced production capacity negatively. These findings point to the reality that coal is unlikely to play a major role in the country's energy equation in the near future unless serious efforts are made to address the above issues.« less

Uranium aqueous speciation in the vicinity of the former uranium mining sites using the diffusive gradients in thin films and ultrafiltration techniques.

PubMed

Drozdzak, Jagoda; Leermakers, Martine; Gao, Yue; Elskens, Marc; Phrommavanh, Vannapha; Descostes, Michael

2016-03-24

The performance of the Diffusive Gradients in Thin films (DGT) technique with Chelex(®)-100, Metsorb™ and Diphonix(®) as binding phases was evaluated in the vicinity of the former uranium mining sites of Chardon and L'Ecarpière (Loire-Atlantique department in western France). This is the first time that the DGT technique with three different binding agents was employed for the aqueous U determination in the context of uranium mining environments. The fractionation and speciation of uranium were investigated using a multi-methodological approach using filtration (0.45 μm, 0.2 μm), ultrafiltration (500 kDa, 100 kDa and 10 kDa) coupled to geochemical speciation modelling (PhreeQC) and the DGT technique. The ultrafiltration data showed that at each sampling point uranium was present mostly in the 10 kDa truly dissolved fraction and the geochemical modelling speciation calculations indicated that U speciation was markedly predominated by CaUO2(CO3)3(2-). In natural waters, no significant difference was observed in terms of U uptake between Chelex(®)-100 and Metsorb™, while similar or inferior U uptake was observed on Diphonix(®) resin. In turn, at mining influenced sampling spots, the U accumulation on DGT-Diphonix(®) was higher than on DGT-Chelex(®)-100 and DGT-Metsorb™, probably because their performance was disturbed by the extreme composition of the mining waters. The use of Diphonix(®) resin leads to a significant advance in the application and development of the DGT technique for determination of U in mining influenced environments. This investigation demonstrated that such multi-technique approach provides a better picture of U speciation and enables to assess more accurately the potentially bioavailable U pool. Copyright © 2016 Elsevier B.V. All rights reserved.

Model for the prediction of subsurface strata movement due to underground mining

NASA Astrophysics Data System (ADS)

Cheng, Jianwei; Liu, Fangyuan; Li, Siyuan

2017-12-01

The problem of ground control stability due to large underground mining operations is often associated with large movements and deformations of strata. It is a complicated problem, and can induce severe safety or environmental hazards either at the surface or in strata. Hence, knowing the subsurface strata movement characteristics, and making any subsidence predictions in advance, are desirable for mining engineers to estimate any damage likely to affect the ground surface or subsurface strata. Based on previous research findings, this paper broadly applies a surface subsidence prediction model based on the influence function method to subsurface strata, in order to predict subsurface stratum movement. A step-wise prediction model is proposed, to investigate the movement of underground strata. The model involves a dynamic iteration calculation process to derive the movements and deformations for each stratum layer; modifications to the influence method function are also made for more precise calculations. The critical subsidence parameters, incorporating stratum mechanical properties and the spatial relationship of interest at the mining level, are thoroughly considered, with the purpose of improving the reliability of input parameters. Such research efforts can be very helpful to mining engineers’ understanding of the moving behavior of all strata over underground excavations, and assist in making any damage mitigation plan. In order to check the reliability of the model, two methods are carried out and cross-validation applied. One is to use a borehole TV monitor recording to identify the progress of subsurface stratum bedding and caving in a coal mine, the other is to conduct physical modelling of the subsidence in underground strata. The results of these two methods are used to compare with theoretical results calculated by the proposed mathematical model. The testing results agree well with each other, and the acceptable accuracy and reliability of the proposed prediction model are thus validated.

Issues of Exploitation of Induction Motors in the Course of Underground Mining Operations

NASA Astrophysics Data System (ADS)

Gumula, Stanisław; Hudy, Wiktor; Piaskowska-Silarska, Malgorzata; Pytel, Krzysztof

2017-09-01

Mining industry is one of the most important customers of electric motors. The most commonly used in the contemporary mining industry is alternating current machines used for processing electrical energy into mechanical energy. The operating problems and the influence of qualitative interference acting on the inputs of individual regulators to field-oriented system in the course of underground mining operations has been presented in the publication. The object of controlling the speed is a slip-ring induction motor. Settings of regulators were calculated using an evolutionary algorithm. Examination of system dynamics was performed by a computer with the use of the MATLAB / Simulink software. According to analyzes, large distortion of input signals of regulators adversely affects the rotational speed that pursued by the control system, which may cause a large vibration of the whole system and, consequently, its much faster destruction. Designed system is characterized by a significantly better resistance to interference. The system is stable with the properly selected settings of regulators, which is particularly important during the operation of machinery used in underground mining.

Occupational Malfunctioning and Fatigue Related Work Stress Disorders (FRWSDs): An Emerging Issue in Indian Underground Mine (UGM) Operations

NASA Astrophysics Data System (ADS)

Dey, Shibaji Ch.; Dey, Netai Chandra; Sharma, Gourab Dhara

2018-04-01

Indian underground mining (UGM) transport system largely deals with different fore and back bearing work processes associated with different occupational disorders and fatigue related work stress disorders (FRWSDs). Therefore, this research study is specifically aimed to determine the fatigue related problems in general and determination of Recovery Heart Rate (Rec HR) pattern and exact cause of FRWSDs in particular. A group of twenty (N = 20) UGM operators are selected for the study. Heart rate profiles and work intensities of selected workforces have been recorded continuously during their regular mine operation and the same workforces are tested on a treadmill on surface with almost same work intensity (%Maximal Heart Rate) which was earlier observed in the mine. Recovery Heart Rate (Rec HR) in both the experiment zones is recorded. It is observed that with almost same work intensity, the recovery patterns of submaximal prolonged work in mine are different as compared to treadmill. This research study indicates that non-biomechanical muscle activity along with environmental stressors may have an influence on recovery pattern and FRWSDs.

On the Role of Mining Exposure in Epigenetic Effects in Parkinson's Disease.

PubMed

Castillo, Sebastian; Muñoz, Patricia; Behrens, Maria Isabel; Diaz-Grez, Fernando; Segura-Aguilar, Juan

2017-08-01

To explore the possible influence of heavy metal mining on incidence of Parkinson's disease (PD), global DNA methylation was assessed in blood samples from a population of PD patients (n = 45) and control subjects (n = 52) in Antofagasta neighborhood, a Chilean city built for exclusive use of mining companies. Comparisons were made with PD subjects (n = 52) and control subjects (n = 59) from Santiago Chile, a city having little association with mining. All subjects were assessed by two neurologists and PD diagnosis was based on UK Parkinson's Disease Society Brain Bank Clinical Diagnostic Criteria. From blood samples obtained from each individual, a decrease in global DNA methylation was observed in PD patients either exposed (49% of control, P < 0.001) or not exposed (47% of control, P < 0.001) to mining activity. Although there was no difference in levels of DNA methylation between PD patients from the two cities, there was a lower level of DNA methylation in control subjects from Santiago versus Antofagasta.

The lead isotopic composition of dust in the vicinity of a uranium mine in northern Australia and its use for radiation dose assessment.

PubMed

Bollhöfer, Andreas; Honeybun, Russell; Rosman, Kevin; Martin, Paul

2006-08-01

Airborne lead isotope ratios were measured via Thermal Ionisation Mass Spectrometry in samples from the vicinity of Ranger uranium mine in northern Australia. Dust deposited on leaves of Acacia spp. was washed off and analysed to gain a geographical snapshot of lead isotope ratios in the region. Aerosols were also collected on Teflon filters that were changed monthly over one seasonal cycle using a low volume diaphragm pump. Lead isotope ratios in dust deposited on leaves overestimate the relative amount of mine origin airborne lead, most likely due to a difference of the size distribution of particles collected on leaves and true aerosol size distribution. Seasonal measurements show that the annual average mine contribution to airborne lead concentrations in Jabiru East, approximately 2.5 km northwest of the mine, amounted to 13%, with distinct differences between the wet and dry season. The relative contribution of mine origin lead deposited on leaves in the dry season drops to less than 1% at a distance of 12.5 km from the mine along the major wind direction. An approach is outlined, in which lead isotope ratios are used to estimate the effective radiation dose received from the inhalation of mine origin radioactivity trapped in or on dust. Using the data from our study, this dose has been calculated to be approximately 2 microSv year(-1) for people living and working in the area.

Radon as a tracer of daily, seasonal and spatial air movements in the Underground Tourist Route "Coal Mine" (SW Poland).

PubMed

Tchorz-Trzeciakiewicz, Dagmara Eulalia; Parkitny, Tomasz

2015-11-01

The surveys of radon concentrations in the Underground Tourist Route "Coal Mine" were carried out using passive and active measurement techniques. Passive methods with application of Solid State Nuclear Track Detectors LR115 were used at 4 points in years 2004-2007 and at 21 points in year 2011. These detectors were exchanged at the beginning of every season in order to get information about seasonal and spatial changes of radon concentrations. The average radon concentration noted in this facility was 799 Bq m(-3) and is consistent with radon concentrations noted in Polish coal mines. Seasonal variations, observed in this underground tourist route, were as follows: the highest radon concentrations were noted during summers, the lowest during winters, during springs and autumns intermediate but higher in spring than in autumn. The main external factor that affected seasonal changes of radon concentrations was the seasonal variation of outside temperature. No correlation between seasonal variations of radon concentrations and seasonal average atmospheric pressures was found. Spatial variations of radon concentrations corresponded with air movements inside the Underground Tourist Route "Coal Mine". The most vivid air movements were noted along the main tunnel in adit and at the place located near no blinded (in the upper part) shaft. Daily variations of radon concentrations were recorded in May 2012 using RadStar RS-230 as the active measurement technique. Typical daily variations of radon concentrations followed the pattern that the highest radon concentrations were recorded from 8-9 a.m. to 7-8 p.m. and the lowest during nights. The main factor responsible for hourly variations of radon concentrations was the daily variation of outside temperatures. No correlations were found between radon concentration and other meteorological parameters such as atmospheric pressure, wind velocity or precipitation. Additionally, the influence of human factor on radon concentrations was noticed. As human factor, we consider open entrance door during restorations works carried out inside the underground facility. Comprehensive surveys of radon concentrations in the Underground Tourist Route "Coal Mine", which included hourly, seasonal and spatial measurements, have revealed that radon can be the excellent tracer of air movements inside the underground facilities that are not equipped with mechanical ventilation system. The main external factor that affects hourly, seasonal and even spatial changes of radon concentrations inside Underground Tourist Route "Coal Mine" is the variation of outside temperature. The maximum effective dose received by employees during 2000 working hours in a year was 5.8 mSv y(-1) and the minimum was 3.5 mSv y(-1). Tourist guides, who usually spend underground about 1000 h y(-1), received effective dose from 1.7 mSv y(-1) to 2.3 mSv y(-1). According to Polish Law, employees, receiving effective dose for occupational exposure higher than 1 mSv y(-1) but below 6 mSv y(-1), are allocated to category B of workers and the level of radiation in their place of work should be controlled and continuously monitored. The radiation monitoring system in the Underground Tourist Route "Coal Mine" does not exist. None of Polish tourist routes or caves has installed radiation monitoring system although effective doses received by employees, in some of them, exceed values defined by law. Effective dose received by tourist during one trip was lower than 0.001 mSv y(-1) and risk of cancer induction was lower than 0.00001%. The probability, that tourists inside the Underground Tourist Route "Coal Mine" receive effective dose exceeding allowable annual limit for members of the public of 1 mSv y(-1) does not exist. The Underground Tourist Route Coal Mine is a safe place for tourists from radiological point of view. Copyright © 2015 Elsevier Ltd. All rights reserved.

Modeling the emission, transport and deposition of contaminated dust from a mine tailing site.

PubMed

Stovern, Michael; Betterton, Eric A; Sáez, A Eduardo; Villar, Omar Ignacio Felix; Rine, Kyle P; Russell, Mackenzie R; King, Matt

2014-01-01

Mining operations are potential sources of airborne particulate metal and metalloid contaminants through both direct smelter emissions and wind erosion of mine tailings. The warmer, drier conditions predicted for the Southwestern US by climate models may make contaminated atmospheric dust and aerosols increasingly important, due to potential deleterious effects on human health and ecology. Dust emissions and dispersion of contaminants from the Iron King Mine tailings in Dewey-Humboldt, Arizona, a Superfund site, are currently being investigated through in situ field measurements and computational fluid dynamics modeling. These tailings are significantly contaminated with lead and arsenic with an average soil concentration of 1616 and 1420 ppm, respectively. Similar levels of these contaminants have also been measured in soil samples taken from the area surrounding the mine tailings. Using a computational fluid dynamics model, we have been able to model dust transport from the mine tailings to the surrounding region. The model includes a distributed Eulerian model to simulate fine aerosol transport and a Lagrangian approach to model fate and transport of larger particles. In order to improve the accuracy of the dust transport simulations both regional topographical features and local weather patterns have been incorporated into the model simulations.

Amending Jasper County, Missouri soils with biochar and ...

EPA Pesticide Factsheets

Abandoned mines and the residuals from mining across the U.S. pose a considerable, pervasive risk to human health and the environment. Many soils in the Tri-State-Mining District (TSMD), located where Missouri, Kansas and Oklahoma meet, have been affected by the residuals of historic lead and zinc mining. Here we describe a research collaboration between ORD and Region 7 to investigate the use of customized soil amendments, which will include biochar, as a tool to provide both soil remediation and reestablishment of a soil-stabilizing native plant community at sites in the TSMD. Biochar is a charcoal-like, carbon-rich, porous by-product of thermal pyrolysis or gasification. A benefit of using biochar is the ability to engineer its properties to correspond to specific soil remediation needs. Specifically, it has properties that make it well suited for use in remediating mine soils and reestablishing vegetation, with studies indicating that biochar can complex and immobilize heavy metals. This is of critical importance for mining influenced sites. However, the optimized biochar properties for the remediation of acidic mine soils are not yet fully known. Biochar can be produced to have a range of pH values, depending upon feedstock and pyrolysis or gasification conditions, and post-production activation. Therefore, this material may be used as a liming agent to raise soil pH. Additionally, some biochars have been shown to improve soil water holding capacities and

Geological and anthropogenic factors influencing mercury speciation in mine wastes: An EXAFS spectroscopy study

USGS Publications Warehouse

Kim, C.S.; Rytuba, J.J.; Brown, Gordon E.

2004-01-01

The speciation of Hg is a critical determinant of its mobility, reactivity, and potential bioavailability in mine-impacted regions. Furthermore, Hg speciation in these complex natural systems is influenced by a number of physical, geological, and anthropogenic variables. In order to investigate the degree to which several of these variables may affect Hg speciation, extended X-ray absorption fine structure (EXAFS) spectroscopy was used to determine the Hg phases and relative proportions of these phases present in Hg-bearing wastes from selected mine-impacted regions in California and Nevada. The geological origin of Hg ore has a significant effect on Hg speciation in mine wastes. Specifically, samples collected from hot-spring Hg deposits were found to contain soluble Hg-chloride phases, while such phases were largely absent in samples from silica-carbonate Hg deposits; in both deposit types, however, Hg-sulfides in the form of cinnabar (HgS, hex.) and metacinnabar (HgS, cub.) dominate. Calcined wastes in which Hg ore was crushed and roasted in excess of 600??C, contain high proportions of metacinnabar while the main Hg-containing phase in unroasted waste rock samples from the same mines is cinnabar. The calcining process is thought to promote the reconstructive phase transformation of cinnabar to metacinnabar, which typically occurs at 345??C. The total Hg concentration in calcines is strongly correlated with particle size, with increases of nearly an order of magnitude in total Hg concentration between the 500-2000 ??m and <45 ??m size fractions (e.g., from 97-810 mg/kg Hg in calcines from the Sulphur Bank Mine, CA). The proportion of Hg-sulfides present also increased by 8-18% as particle size decreased over the same size range. This finding suggests that insoluble yet soft Hg-sulfides are subject to preferential mechanical weathering and become enriched in the fine-grained fraction, while soluble Hg phases are leached out more readily as particle size decreases. The speciation of Hg in mine wastes is similar to that in distributed sediments located downstream from the same waste piles, indicating that the transport of Hg from mine waste piles does not significantly impact Hg speciation. Hg LIII-EXAFS analysis of samples from Au mining regions, where elemental Hg(0) was introduced to aid in the Au recovery process, identified the presence of Hg-sulfides and schuetteite (Hg3O2SO4), which may have formed as a result of long-term Hg(0) burial in reducing high-sulfide sediments. ?? 2003 Elsevier Ltd. All rights reserved.

In-mine testing of a natural background sensor, part B

NASA Technical Reports Server (NTRS)

Martzloff, F. D.

1981-01-01

The capability of a natural background sensor for measuring the thickness of top coal on a longwall face was examined. The limitations on the time during which tests could be performed, and the roof conditions, did not produce readings of top coal measurements during the shearer operation. It was demonstrated that the system is capable to survive operating conditions in the mine environment, while the static tests confirmed that the natural background sensor approach is a valid method of measuring top coal thickness in mines where the roof rock provides a constant radiation level. It is concluded that the practical results will improve sequent development of an integrated vertical control system which is information from the natural background system.

Isotope biogeochemical assessment of natural biodegradation processes in open cast pit mining landscapes

NASA Astrophysics Data System (ADS)

Jeschke, Christina; Knöller, Kay; Koschorreck, Matthias; Ussath, Maria; Hoth, Nils

2014-05-01

In Germany, a major share of the energy production is based on the burning of lignite from open cast pit mines. The remediation and re-cultivation of the former mining areas in the Lusatian and Central German lignite mining district is an enormous technical and economical challenge. After mine closures, the surrounding landscapes are threatened by acid mine drainage (AMD), i.e. the acidification and mineralization of rising groundwater with metals and inorganic contaminants. The high content of sulfur (sulfuric acid, sulfate), nitrogen (ammonium) and iron compounds (iron-hydroxides) deteriorates the groundwater quality and decelerates sustainable development of tourism in (former) mining landscapes. Natural biodegradation or attenuation (NA) processes of inorganic contaminants are considered to be a technically low impact and an economically beneficial solution. The investigations of the stable isotope compositions of compounds involved in NA processes helps clarify the dynamics of natural degradation and provides specific informations on retention processes of sulfate and nitrogen-compounds in mine dump water, mine dump sediment, and residual pit lakes. In an active mine dump we investigated zones where the process of bacterial sulfate reduction, as one very important NA process, takes place and how NA can be enhanced by injecting reactive substrates. Stable isotopes signatures of sulfur and nitrogen components were examined and evaluated in concert with hydrogeochemical data. In addition, we delineated the sources of ammonium pollution in mine dump sediments and investigated nitrification by 15N-labeling techniques to calculate the limit of the conversion of harmful ammonium to nitrate in residual mining lakes. Ultimately, we provided an isotope biogeochemical assessment of natural attenuation of sulfate and ammonium at mine dump sites and mining lakes. Also, we estimated the risk potential for water in different compartments of the hydrological system. In laboratory experiments, we tested reactive materials that may speed up the process of bacterial sulfate reduction. In in-situ experiments, we quantified nitrification rates. Based on the results, we are able to suggest promising technical measures that enhance natural attenuation processes at mine dump site and in mining lakes. The natural water cycle in lignite mining landscapes is heavily impacted by human activities. Basically, nature is capable of cleaning itself to a certain extent after mining activities stopped. However, it is our responsibility to support biogeochemical processes to make them more efficient and more sustainable. Isotopic monitoring proved to be an excellent tool for assessing the relevance and performance of different re-cultivation measures for a positive long-term development of the water quality in large-scale aquatic systems affected by the impact of lignite mining.

Soil amendments improve microbial ecology parameters of "topsoil inoculum" used in post-mining restoration

NASA Astrophysics Data System (ADS)

Kumaresan, Deepak; Munoz-Rojas, Miriam; Moreira-Grez, Benjamin; Kariman, Khalil; Whiteley, Andrew

2017-04-01

Mine operations generate substantial volumes of waste substrates, which are crushed and/or chemically treated waste rock from which ores are extracted. Establishment of rehabilitated landforms using post-mining substrates (i.e. waste rocks, tailings) that typically exhibit extreme conditions (such as high pH, nutrient deficiency, excessive salinity and metal toxicity) can be a major environmental problem and a critical issue during mine closure operations. More importantly, mine sites are located predominantly in arid or semi-arid lands where our understanding of basic ecosystem processes and microbial interactions with native plants (e.g. Eucalyptus spp., Acacia spp., Grevillea spp. in Western Australia) are limited. Despite the wide acknowledgement on the impact of microbial functional diversity on overall soil and plant health, no detailed attention has been paid to understand the role of belowground microbial functional diversity in the context of mine rehabilitation strategies. In this research, we investigated the role of nitrogen-based and microbial consortia amendments on improving the microbial ecology parameters of "topsoil inoculum" and subsequently its cascading effect on seedling establishment and plant morphology of Acacia ancistrocarpa, a legume native to the Pilbara and other regions of Western Australia and commonly used in arid zone restoration. The study was conducted under controlled environmental conditions in potted plants using topsoil retrieved from previously stockpiled material as growth media. A morphological assessment was undertaken to measure shoot length, shoot weight, root length, root area and root weight. Soil chemical properties, e.g. carbon, nitrogen and trace metals concentrations were determined Microbial activity was measured with the 1-day CO2 test, which determines soil microbial respiration rate based on the measurement of the CO2 burst produced after moistening dry soil (Muñoz-Rojas et al., 2016). Bacterial and archaeal community composition was assessed using high-throughput sequencing of the 16S rRNA marker gene analysis (Whiteley et al., 2012). Our results showed significant (P <0.05) larger rates of microbial activity and shoot:root ratio in those pots amended with both N and microbial consortia. Both amendments significantly influenced the chemical and bacterial-archaeal community composition in the topsoil inoculum. Topsoil amended with inorganic nitrogen revealed higher relative abundance of 16S rRNA gene sequences related to phylum Nitrospira, Planctomycetes, Gemmatimonadetes and Cyanobacteria/Chloroplast in comparison to "water-only" (control) and "microbial consortia" treatment. Addition of microbial consortia to topsoil significantly increased the concentrations of soil potassium, iron, copper and manganese. Interestingly, a large proportion of sequences that can only be assigned at the domain level (either Bacteria or Archaea) were detected in the control samples suggesting the presence of novel taxa/lineages in the native soil and their relative abundances are significantly influenced by the addition of amendments. Our data indicates that whilst amendments results significant improvement of plant growth and establishment at early stages it also results in considerable phylogenetic divergence within soil bacterial/archaeal communities, in particular loss of indigenous taxa/lineages that could have above-below ground feedback with native plants. Muñoz-Rojas M, Erickson TE, Martini D, Dixon KW, Merritt DJ. 2016. Soil physicochemical and microbiological indicators of short, medium and long term post-fire recovery in semi-arid ecosystems. Ecological indicators 63, 14-22.DOI: 10.1016/j.ecolind.2015.11.038 Whiteley AS, Jenkins S, Waite I, Kresoje N, Payne H, Mullan B, Allcock R, O'Donnell AG. Microbial 16S rRNA Ion Tag and community metagenome sequencing using the Ion Torrent (PGM) Platform. J Microbiol Methods 91, 80-88, doi:10.1016/j.mimet.2012.07.008 (2012).

2006 SME annual meeting & 7th ICARD, March 26-29, 2006, St. Louis, Missouri. Pre-prints

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

2006-07-01

Subjects covered by the papers include: enhanced coalbed methane through carbon sequestration, application of laser surface coatings for raw coal screen wear resistance enhancement, application of cross-flow teeter-bed separator in the US coal industry, arsenic removal from drinking water, modelling of fire spread along combustibles in a mine entry, coal's role in sustaining society, real time characterisation of frother bubble thin films, diesel emissions, overcoming stress measurements form underground coal amines, dry jigging coal, estimation of roof strata strength, improving screen bowl centrifuge performance, installation of ventilation shaft at a New Mexico coal mine, evaluation of feasibility of CO{sub 2}more » sequestration in deep coal, robot-human control interaction in mining operations, small mine and contractor safety, coal dust explosibility meter, US coal mine fatalities versus age of mine, and water and slurry bulkheads in underground coal mines.« less

Dewatering of the Jenkins open pit uranium mine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Straskraba, V.; Kissinger, L.E.

Mining of low grade uranium sandstones in the Jenkins open pit mine in the Shirley Basin, Wyoming was troubled by slope failures and wet conditions in the pit. Since the mine was expanding toward a river, the possibility of drainage from this river into the mine raised serious concern during the mine planning. A baseline hydrogeologic study was performed and dewatering measures were designed with the help of a numerical mathematical model. A combination of dewatering wells installed from the surface around the perimeter of the pit and horizontal drains in areas of high slope failure potential substantially improved themore » mining conditions and slope stability. This procedure consequently led to the successful ore recovery from the highly saturated sandstone strata. The development of drawdown during the dewatering of two separated aquifers in the overburden was close to that predicted by the model.« less

Mining injuries in Serbian underground coal mines -- a 10-year study.

PubMed

Stojadinović, Saša; Svrkota, Igor; Petrović, Dejan; Denić, Miodrag; Pantović, Radoje; Milić, Vitomir

2012-12-01

Mining, especially underground coal mining, has always been a dangerous occupation. Injuries, unfortunately, even those resulting in death, are one of the major occupational risks that all miners live with. Despite the fact that all workers are aware of the risk, efforts must be and are being made to increase the safety of mines. Injury monitoring and data analysis can provide us with valuable data on the causes of accidents and enable us to establish a correlation between the conditions in the work environment and the number of injuries, which can further lead to proper preventive measures. This article presents the data on the injuries in Serbian coal mines during a 10-year period (2000-2009). The presented results are only part of an ongoing study whose aim is to assess the safety conditions in Serbian coal mines and classify them according to that assessment. Copyright © 2011 Elsevier Ltd. All rights reserved.

Energy saving analysis on mine-water source heat pump in a residential district of Henan province, central China

NASA Astrophysics Data System (ADS)

Wang, Hong; Duan, Huanlin; Chen, Aidong

2018-02-01

In this paper, the mine-water source heat pump system is proposed in residential buildings of a mining community. The coefficient of performance (COP) and the efficiency of exergy are analyzed. The results show that the COP and exergy efficiency of the mine-water source heat pump are improved, the exergy efficiency of mine-water source heat pump is more than 10% higher than that of the air source heat pump.The electric power conservation measure of “peak load shifting” is also emphasized in this article. It shows that itis a very considerable cost in the electric saving by adopting the trough period electricity to produce hot water. Due to the proper temperature of mine water, the mine-watersource heat pump unit is more efficient and stable in performance, which further shows the advantage of mine-water source heat pump in energy saving and environmental protection. It provides reference to the design of similar heat pump system as well.

Performance analysis of a multispectral system for mine detection in the littoral zone

NASA Astrophysics Data System (ADS)

Hargrove, John T.; Louchard, Eric

2004-09-01

Science & Technology International (STI) has developed, under contract with the Office of Naval Research, a system of multispectral airborne sensors and processing algorithms capable of detecting mine-like objects in the surf zone. STI has used this system to detect mine-like objects in a littoral environment as part of blind tests at Kaneohe Marine Corps Base Hawaii, and Panama City, Florida. The airborne and ground subsystems are described. The detection algorithm is graphically illustrated. We report on the performance of the system configured to operate without a human in the loop. A subsurface (underwater bottom proud mine in the surf zone and moored mine in shallow water) mine detection capability is demonstrated in the surf zone, and in shallow water with wave spillage and foam. Our analysis demonstrates that this STI-developed multispectral airborne mine detection system provides a technical foundation for a viable mine counter-measures system for use prior to an amphibious assault.

Soil quality and water redistribution influences on plant production over low hillslopes on reclaimed mined land

USDA-ARS?s Scientific Manuscript database

A basic part of soils’ delivery of ecosystem services is the interaction between plant growth response to soil quality (SQ) factors at point scale and water redistribution effects at hillslope scale. To study the influence of SQ-indicator properties and water redistribution, we examined hillslope pr...

Radiometric surveying for the assessment of radiation dose and radon specific exhalation in underground environment

NASA Astrophysics Data System (ADS)

Bochiolo, M.; Verdoya, M.; Chiozzi, P.; Pasquale, V.

2012-08-01

We performed a radiometric survey for evaluating the natural radioactivity and the related potential hazard level both outdoor and indoor a mine tunnel. The mine is located in a zone of uranium enrichment in the Western Alps (Italy). At first, a γ-ray spectrometry survey of the area surrounding the mine was carried out to define the extent of the ore deposit. Then, spectrometric measurements were performed in the tunnel and rock samples were collected for laboratory analyses. The results point to significant heterogeneity in uranium concentration and consequently in the absorbed dose rate spatial distribution. Spectrometric results in situ and in the laboratory, together with radon air concentration measurements, were used to infer the radon specific exhalation and flow from the mine rocks. The specific exhalation is positively related to the activity concentration of uranium.

Characterization and quantification of geochemical reaction rates in mine waste piles using unsaturated zone gases

NASA Astrophysics Data System (ADS)

Birkham, T.; Hendry, J.; Kirkland, R.; Bradley, S.; Mendoza, C.; Wassenaar, L.

2003-04-01

From 1997 to the present, we have installed and monitored 240 gas probes (maximum depth of 43 m) in unsaturated waste rock, overburden and tailings piles at a uranium mine in northern Saskatchewan, Canada and an oil sands mine in northern Alberta, Canada. Depth profiles of O2, CO2, N2 and CH4 pore-gas concentrations, temperature, and moisture content were measured in the field and used to characterize and quantifyin situ geochemical reaction rates. An innovative field-portable GC system has been developed to monitor pore-gas concentrations. At most sites, gas migration has been attributed to diffusion. At sites where advective transport may be important, subsurface total pressure measurements have been used to assess the contribution of advection to gas migration. The stable isotopes of molecular O2 (16O2 and 18O16O) and C in CO2 (12CO2 and 13CO2) have also been measured and modeled. At the uranium mine, the modelling of the O2, CO2, δ18OO2, and δ13CCO2 depth profiles was used to identify an alternative mechanism of O2 consumption and CO2 production in mine waste-rock piles. At the oil sands mine, a complex and unique system involving O2, CO2, and CH4 fluxes in the unsaturated zone and across the capillary fringe has been identified and is currently being modeled.