Using Cascading Style Sheets to Design a Fly-Out Menu with Microsoft Visual Studio

ERIC Educational Resources Information Center

Liu, Chang; Downing, Charles

2010-01-01

The menu has become an integrated component within nearly all professionally designed websites. This teaching tip presents a no-code way to design either a vertical or a horizontal fly-out menu by using Cascading Style Sheets (CSS) within Microsoft Visual Studio 2008. The approach described in this tip helps students fully understand how to…

The effect of broken stringers on the stress intensity factor for a uniformly stiffened sheet containing a crack

NASA Technical Reports Server (NTRS)

Poe, C. C., Jr.

1973-01-01

A linear elastic stress analysis was made of a centrally cracked sheet stiffened by riveted, uniformly spaced and sized stringers. The stress intensity factor for the sheet and the load concentration factor for the most highly loaded stringer were determined for various numbers of broken stringers. A broken stringer causes the stress intensity factor to be very high when the crack tip is near the broken stringer, but causes little effect when the crack tip extends beyond several intact stringers. A broken stringer also causes an increase in the load concentration factor of the adjacent stringers. The calculated residual strengths and fatigue-crack-growth lives of a stiffened aluminum sheet with a broken stringer were only slightly less than a sheet with all intact stringers, and were still much higher than those of an unstiffened sheet.

Effect of debond growth on stress-intensity factors in a cracked orthotropic sheet stiffened by a semi-infinite orthotropic sheet

NASA Technical Reports Server (NTRS)

Bigelow, C. A.

1986-01-01

Stress-intensity factors are determined for a cracked infinite sheet adhesively bonded to a stringer, and debonding of the adhesive layer is predicted. The stringer is modeled as a semi-infinite sheet. Adhesive nonlinearity is also included. Both the sheet and stringer are treated as homogeneous, orthotropic materials. A set of integral equations is formulated and solved to obtain the adhesive shear stresses and crack-tip stress-intensity factors. Adhesive debonding is predicted using a rupture criterion based on the combined adhesive stresses. When the crack is not under the stringer, the debond extends along the edge of the stringer. When the crack tip is beneath the stringer, the debond grows to the end of the crack, then along the edge of the stringer. Stress levels required for debond initiation decrease as the crack tip is moved beneath the stringer. With a nonlinear adhesive, the debond initiates at higher applied stress levels than in linear adhesive cases. Compared with the linear adhesive solution, modeling a nonlinear adhesive causes the stress-intensity factor to increase when the bond is assumed to remain intact but causes the stress-intensity factor to decrease when debonding is included.

Hazard Communication Standard for Chemical Labels and Safety Data Sheets In GHS Format

EPA Pesticide Factsheets

This fact sheet provides an overview of the required contents of Safety Data Sheets (SDSs) and chemical hazard labels, and includes tips on how these materials can be used to better protect health and the environment.

Astronaut Jerry Linenger with sheet of TIPS correspondence

NASA Image and Video Library

1994-09-15

STS064-23-025 (9-20 Sept. 1994) --- With scissors in hand, astronaut Jerry M. Linenger, STS-64 mission specialist, prepares to cut off a lengthy sheet of correspondence from ground controllers. Called the Thermal Imaging Printing System (TIPS), the message center occupies a stowage locker on the space shuttle Discovery's middeck. Astronaut L. Blaine Hammond, pilot, retrieves a clothing item from a nearby locker. Photo credit: NASA or National Aeronautics and Space Administration

Efficient fabrication of carbon nanotube micro tip arrays by tailoring cross-stacked carbon nanotube sheets.

PubMed

Wei, Yang; Liu, Peng; Zhu, Feng; Jiang, Kaili; Li, Qunqing; Fan, Shoushan

2012-04-11

Carbon nanotube (CNT) micro tip arrays with hairpin structures on patterned silicon wafers were efficiently fabricated by tailoring the cross-stacked CNT sheet with laser. A blade-like structure was formed at the laser-cut edges of the CNT sheet. CNT field emitters, pulled out from the end of the hairpin by an adhesive tape, can provide 150 μA intrinsic emission currents with low beam noise. The nice field emission is ascribed to the Joule-heating-induced desorption of the emitter surface by the hairpin structure, the high temperature annealing effect, and the surface morphology. The CNT emitters with hairpin structures will greatly promote the applications of CNTs in vacuum electronic devices and hold the promises to be used as the hot tips for thermochemical nanolithography. More CNT-based structures and devices can be fabricated on a large scale by this versatile method. © 2012 American Chemical Society

Peeling without precursors

NASA Astrophysics Data System (ADS)

Lister, John; Skinner, Dominic; Large, Tim

2017-11-01

The peeling by fluid injection of an elastic sheet away from a substrate is often regularised by invoking a thin prewetting film or a low-viscosity phase in the tip. Here we analyse fluid-driven peeling without such precursors, and consider an elastic sheet either bonded to, or simply laid on, an elastic substrate. To resolve the `elastic contact-line problem' that arises from viscous flow and beam theory, we determine the near-tip behaviour from lubrication theory coupled to the full equations of elasticity and fracture. The result is a law for the tip propagation speed in terms of the remote loading and the toughness of the sheet-substrate bonding (which might be zero). There are distinct modes of failure, according to whether there is slip ahead of the fluid front. The propagation-speed law gives rise to new similarity solutions for the spread of a fluid-filled blister in different regimes.

Social Media Tips to Enhance Medical Education.

PubMed

Shah, Vikas; Kotsenas, Amy L

2017-06-01

In this article, we describe how social media can supplement traditional education, articulate the advantages and disadvantages of various social media platforms for both teachers and learners, discuss best practices to maintain confidentiality of protected health information, and provide tips for implementing social media-based teaching into the training curriculum. Copyright © 2017 The Association of University Radiologists. All rights reserved.

Lighting: Traffic Safety Tips

DOT National Transportation Integrated Search

1996-01-01

This fact sheet, NHTSA Facts: Summer 1996, discusses traffic safety tips on motor vehicle lighting, including headlights, tail lights, and signal lights. It details the cleaning of headlamps, proper aiming of headlamps, and replacement of burned out ...

Safe Travel Tips for Older Adults

MedlinePlus

... our other tip sheets. Before you board a plane, train, cruise, or get in your car for ... sanitizer, especially after spending time on a crowded plane, train, or bus, and before eating. Use common ...

Girlfriends' Health and Safety Tips

MedlinePlus

... Disease Fact Sheet Women's Health Healthy Weight Lesbian, Gay, Bisexual, and Transgender Health Minority Health Preconception Health ... Disease Fact Sheet Women's Health Healthy Weight Lesbian, Gay, Bisexual, and Transgender Health Minority Health Preconception Health ...

Twelve tips for using social media as a medical educator.

PubMed

Kind, Terry; Patel, Pradip D; Lie, Désirée; Chretien, Katherine C

2014-04-01

We now live, learn, teach and practice medicine in the digital era. Social networking sites are used by at least half of all adults. Engagement with social media can be personal, professional, or both, for health-related and educational purposes. Use is often public. Lapses in professionalism can have devastating consequences, but when used well social media can enhance the lives of and learning by health professionals and trainees, ultimately for public good. Both risks and opportunities abound for individuals who participate, and health professionals need tips to enhance use and avoid pitfalls in their use of social media and to uphold their professional values. This article draws upon current evidence, policies, and the authors' experiences to present best practice tips for health professions educators, trainees, and students to build a framework for navigating the digital world in a way that maintains and promotes professionalism. These practical tips help the newcomer to social media get started by identifying goals, establishing comfort, and connecting. Furthermore, users can ultimately successfully contribute, engage, learn, and teach, and model professional behaviors while navigating social media.

Choosing Whole-Grain Foods: 10 Tips for Purchasing and Storing Whole-Grain Foods

MedlinePlus

... Price Tag Read the Food Label Kitchen Timesavers Cooking for Your Family Tasty & Low-Cost Recipes Sample 2-Week Menus Resources for Professionals MyPlate Tip Sheets Print Materials Infographics 5 Ways ...

Mature Drivers: Traffic Safety Tips

DOT National Transportation Integrated Search

1996-01-01

This fact sheet, NHTSA Facts: Summer 1996, discusses safety tips for drivers aged 70 and older. It notes that mature drivers: rank lower in aggressive actions; tend to make necessary safety adjustments in their driving, based on their own experience;...

Sport Utility Vehicles: Traffic Safety Tips

DOT National Transportation Integrated Search

1996-01-01

This fact sheet, NHTSA Facts: Summer 1996, describe traffic safety tips for driving sport utility vehicles. Because sport utility vehicles have a higher center of gravity, making them more top heavy than cars, they handle and maneuver differently tha...

Brakes: Traffic Safety Tips

DOT National Transportation Integrated Search

1996-01-01

This fact sheet, NHTSA Facts: Summer 1996, describes traffic safety tips about brakes. It discusses drum brakes, disc brakes, and antilock braking systsms. It notes that there are government standards for brakes, and describes how to take care of bra...

Tip Vortices of Isolated Wings and Helicopter Rotor Blades.

DTIC Science & Technology

1987-12-01

root to tip, as expected due to the induced downwash of the tip vor- tex and wake vortex sheet. Although the three different tip-caps produce very...the inherent limitation of not being able to model the vortex wake with these equations, although the Euler formulation has in it the necessary...physics to model vorticity transport correctly. These equations basically lack the physical mecha- nism needed to generate the vortex wake . However, in

Fact Sheet for Preventing and Detecting PCB Contamination in Used Oil

EPA Pesticide Factsheets

This fact sheet provides tips on how to reduce the mismanagement of used oil contaminated with PCBs, a recurring issue faced by EPA and states, commercial and municipal used oil collection centers and recyclers.

Association Between Media Dose, Ad Tagging, and Changes in Web Traffic for a National Tobacco Education Campaign: A Market-Level Longitudinal Study.

PubMed

Shafer, Paul R; Davis, Kevin C; Patel, Deesha; Rodes, Robert; Beistle, Diane

2016-02-17

In 2012, the US Centers for Disease Control and Prevention (CDC) launched Tips From Former Smokers (Tips), the first federally funded national tobacco education campaign. In 2013, a follow-up Tips campaign aired on national cable television networks, radio, and other channels, with supporting digital advertising to drive traffic to the Tips campaign website. The objective of this study was to use geographic and temporal variability in 2013 Tips campaign television media doses and ad tagging to evaluate changes in traffic to the campaign website in response to specific doses of campaign media. Linear regression models were used to estimate the dose-response relationship between weekly market-level television gross rating points (GRPs) and weekly Web traffic to the Tips campaign website. This relationship was measured using unique visitors, total visits, and page views as outcomes. Ad GRP effects were estimated separately for ads tagged with the Tips campaign website URL and 1-800-QUIT-NOW. In the average media market, an increase of 100 television GRPs per week for ads tagged with the Tips campaign website URL was associated with an increase of 650 unique visitors (P<.001), 769 total visits (P<.001), and 1255 total page views (P<.001) per week. The associations between GRPs for ads tagged with 1-800-QUIT-NOW and each Web traffic measure were also statistically significant (P<.001), but smaller in magnitude. Based on these findings, we estimate that the 16-week 2013 Tips television campaign generated approximately 660,000 unique visitors, 900,000 total visits, and 1,390,000 page views for the Tips campaign website. These findings can help campaign planners forecast the likely impact of targeted advertising efforts on consumers' use of campaign-specific websites.

Interaction of multiarmed spirals in bistable media.

PubMed

He, Ya-feng; Ai, Bao-quan; Liu, Fu-cheng

2013-05-01

We study the interaction of both dense and sparse multiarmed spirals in bistable media modeled by equations of the FitzHugh-Nagumo type. A dense one-armed spiral is characterized by its fixed tip. For dense multiarmed spirals, when the initial distance between tips is less than a critical value, the arms collide, connect, and disconnect continuously as the spirals rotate. The continuous reconstruction between the front and the back drives the tips to corotate along a rough circle and to meander zigzaggedly. The rotation frequency of tip, the frequency of zigzagged displacement, the frequency of spiral, the oscillation frequency of media, and the number of arms satisfy certain relations as long as the control parameters of the model are fixed. When the initial distance between tips is larger than the critical value, the behaviors of individual arms within either dense or sparse multiarmed spirals are identical to that of corresponding one-armed spirals.

Earned media and public engagement with CDC's "Tips from Former Smokers" campaign: an analysis of online news and blog coverage.

PubMed

Kornfield, Rachel; Smith, Katherine Clegg; Szczypka, Glen; Vera, Lisa; Emery, Sherry

2015-01-20

In March 2012, the US Centers for Disease Control and Prevention (CDC) launched the first-ever paid national tobacco education campaign. At a cost of US $54 million, "Tips from Former Smokers" (Tips) ran for 3 months across multiple media, depicting the suffering experienced by smokers and their families in graphic detail. The potential impact and reach of the Tips campaign was not limited to that achieved through paid media placements. It was also potentially extended through "earned media", including news and blog coverage of the campaign. Such coverage can shape public understanding of and facilitate public engagement with key health issues. To better understand the contribution of earned media to the public's engagement with health issues in the current news media environment, we examined the online "earned media" and public engagement generated by one national public health campaign. We constructed a purposive sample of online media coverage of the CDC's 2012 Tips from Former Smokers television campaign, focusing on 14 influential and politically diverse US news outlets and policy-focused blogs. We identified relevant content by combining campaign and website-specific keywords for 4 months around the campaign release. Each story was coded for content, inclusion of multimedia, and measures of audience engagement. The search yielded 36 stories mentioning Tips, of which 27 were focused on the campaign. Story content between pieces was strikingly similar, with most stories highlighting the same points about the campaign's content, cost, and potential impact. We saw notable evidence of audience engagement; stories focused on Tips generated 9547 comments, 8891 Facebook "likes", 1027 tweets, and 505 story URL shares on Facebook. Audience engagement varied by story and site, as did the valence and relevance of associated audience comments. Comments were most oppositional on CNN and most supportive on Yahoo. Comment coding revealed approximately equal levels of opposition and support overall. We identified four common arguments among oppositional comments: government intrusion on personal behaviors, problematic allocation of governmental spending, questionable science, and challenges regarding campaign efficacy. Supportive comments tended to convey personal stories and emotions. The Tips campaign received limited coverage on either online news or blog sources, but the limited number of stories generated engagement among online audiences. In addition to the content and volume of blog and news coverage, audience comments and websites' mechanisms for sharing stories via social media are likely to determine the influence of online earned media. In order to facilitate meaningful evaluation of public health campaigns within the rapidly advancing media environment, there is a need for the public health community to build consensus regarding collection and assessment of engagement data.

Safety Belt Use: Traffic Safety Tips

DOT National Transportation Integrated Search

1996-01-01

This fact sheet, NHTSA Facts: Summer 1996, discusses traffic safety tips for wearing seat belts. It describes the correct way to wear a seat belt, how to sit, and differentiates between lap belts and shoulder belts. It points out that air bags provid...

Media Libraries in Action for Administrators, Teachers, Media Librarians, Library Technicians/Aides, and Volunteer Parents (Helping Programs Grow).

ERIC Educational Resources Information Center

Franklin, Esther, Ed.

Suggestions for improving school library and media services are offered by elementary school media staff in the Sacramento (California) area. This manual consists of one-page reference sheets for each school that responded to a request to share helpful ideas on media services. In addition to a helpful idea or ideas, each sheet includes the name of…

The future of ice sheets and sea ice: between reversible retreat and unstoppable loss.

PubMed

Notz, Dirk

2009-12-08

We discuss the existence of cryospheric "tipping points" in the Earth's climate system. Such critical thresholds have been suggested to exist for the disappearance of Arctic sea ice and the retreat of ice sheets: Once these ice masses have shrunk below an anticipated critical extent, the ice-albedo feedback might lead to the irreversible and unstoppable loss of the remaining ice. We here give an overview of our current understanding of such threshold behavior. By using conceptual arguments, we review the recent findings that such a tipping point probably does not exist for the loss of Arctic summer sea ice. Hence, in a cooler climate, sea ice could recover rapidly from the loss it has experienced in recent years. In addition, we discuss why this recent rapid retreat of Arctic summer sea ice might largely be a consequence of a slow shift in ice-thickness distribution, which will lead to strongly increased year-to-year variability of the Arctic summer sea-ice extent. This variability will render seasonal forecasts of the Arctic summer sea-ice extent increasingly difficult. We also discuss why, in contrast to Arctic summer sea ice, a tipping point is more likely to exist for the loss of the Greenland ice sheet and the West Antarctic ice sheet.

The future of ice sheets and sea ice: Between reversible retreat and unstoppable loss

PubMed Central

Notz, Dirk

2009-01-01

We discuss the existence of cryospheric “tipping points” in the Earth's climate system. Such critical thresholds have been suggested to exist for the disappearance of Arctic sea ice and the retreat of ice sheets: Once these ice masses have shrunk below an anticipated critical extent, the ice–albedo feedback might lead to the irreversible and unstoppable loss of the remaining ice. We here give an overview of our current understanding of such threshold behavior. By using conceptual arguments, we review the recent findings that such a tipping point probably does not exist for the loss of Arctic summer sea ice. Hence, in a cooler climate, sea ice could recover rapidly from the loss it has experienced in recent years. In addition, we discuss why this recent rapid retreat of Arctic summer sea ice might largely be a consequence of a slow shift in ice-thickness distribution, which will lead to strongly increased year-to-year variability of the Arctic summer sea-ice extent. This variability will render seasonal forecasts of the Arctic summer sea-ice extent increasingly difficult. We also discuss why, in contrast to Arctic summer sea ice, a tipping point is more likely to exist for the loss of the Greenland ice sheet and the West Antarctic ice sheet. PMID:19884496

Does self-directed and web-based support for parents enhance the effects of viewing a reality television series based on the Triple P-Positive Parenting Programme?

PubMed

Sanders, Matthew; Calam, Rachel; Durand, Marianne; Liversidge, Tom; Carmont, Sue Ann

2008-09-01

This study investigated whether providing self-directed and web-based support for parents enhanced the effects of viewing a reality television series based on the Triple P - Positive Parenting Programme. Parents with a child aged 2 to 9 (N = 454) were randomly assigned to either a standard or enhanced intervention condition. In the standard television alone viewing condition, parents watched the six-episode weekly television series, 'Driving Mum and Dad Mad'. Parents in the enhanced television viewing condition received a self-help workbook, extra web support involving downloadable parenting tip sheets, audio and video streaming of positive parenting messages and email support, in addition to viewing the television series. Parents in both conditions reported significant improvements in their child's disruptive behaviour and improvements in dysfunctional parenting practices. Effects were greater for the enhanced condition as seen on the ECBI, two of the three parenting indicators and overall programme satisfaction. However, no significant differences were seen on other measures, including parent affect indicators. The level of improvement was related to number of episodes watched, with greatest changes occurring in families who watched each episode. Improvements achieved at post-intervention by parents in both groups were maintained at six-month follow-up. Online tip sheets were frequently accessed; uptake of web-based resources was highest early in the series. The value of combining self-help approaches, technology and media as part of a comprehensive public health approach to providing parenting support is discussed.

Influence of Crack-Tip Configurations on the Fracture Response of 0.04-Inch Thick 2024-T3 Aluminum Alloy Sheet

NASA Technical Reports Server (NTRS)

Johnston, William M.; Newman, James C. (Technical Monitor)

2002-01-01

A series of fracture tests were conducted on Middle-crack tension M(T) and compact tension C(T) specimens to determine the effects of specimen type, specimen width, notch tip sharpness and buckling on the fracture behavior of cracked thin sheet (0.04 inch thick) 2024-T3 aluminum alloy material. A series of M(T) specimens were tested with three notch tip configurations: (1) a fatigue pre-cracked notch, (2) a 0.010-inch-diameter wire electrical discharge machined (EDM) notch, and (3) a EDM notch sharpened with a razor blade. The test procedures are discussed and the experimental results for failure stress, load vs. crack extension and the material stress-strain response are reported.

Association Between Media Dose, Ad Tagging, and Changes in Web Traffic for a National Tobacco Education Campaign: A Market-Level Longitudinal Study

PubMed Central

Davis, Kevin C; Patel, Deesha; Rodes, Robert; Beistle, Diane

2016-01-01

Background In 2012, the US Centers for Disease Control and Prevention (CDC) launched Tips From Former Smokers (Tips), the first federally funded national tobacco education campaign. In 2013, a follow-up Tips campaign aired on national cable television networks, radio, and other channels, with supporting digital advertising to drive traffic to the Tips campaign website. Objective The objective of this study was to use geographic and temporal variability in 2013 Tips campaign television media doses and ad tagging to evaluate changes in traffic to the campaign website in response to specific doses of campaign media. Methods Linear regression models were used to estimate the dose-response relationship between weekly market-level television gross rating points (GRPs) and weekly Web traffic to the Tips campaign website. This relationship was measured using unique visitors, total visits, and page views as outcomes. Ad GRP effects were estimated separately for ads tagged with the Tips campaign website URL and 1-800-QUIT-NOW. Results In the average media market, an increase of 100 television GRPs per week for ads tagged with the Tips campaign website URL was associated with an increase of 650 unique visitors (P<.001), 769 total visits (P<.001), and 1255 total page views (P<.001) per week. The associations between GRPs for ads tagged with 1-800-QUIT-NOW and each Web traffic measure were also statistically significant (P<.001), but smaller in magnitude. Conclusions Based on these findings, we estimate that the 16-week 2013 Tips television campaign generated approximately 660,000 unique visitors, 900,000 total visits, and 1,390,000 page views for the Tips campaign website. These findings can help campaign planners forecast the likely impact of targeted advertising efforts on consumers’ use of campaign-specific websites. PMID:26887959

A Cost-Effectiveness Analysis of the First Federally Funded Antismoking Campaign

PubMed Central

Xu, Xin; Alexander, Robert L.; Simpson, Sean A.; Goates, Scott; Nonnemaker, James M.; Davis, Kevin C.; McAfee, Tim

2015-01-01

Background In 2012, CDC launched the first federally funded national mass media antismoking campaign. The Tips From Former Smokers (Tips) campaign resulted in a 12% relative increase in population-level quit attempts. Purpose Cost-effectiveness analysis was conducted in 2013 to evaluate Tips from a funding agency’s perspective. Methods Estimates of sustained cessations; premature deaths averted; undiscounted life years (LYs) saved; and quality-adjusted life years (QALYs) gained by Tips were estimated. Results Tips saved about 179,099 QALYs and prevented 17,109 premature deaths in the U.S. With the campaign cost of roughly $48 million, Tips spent approximately $480 per quitter, $2,819 per premature death averted, $393 per LY saved, and $268 per QALY gained. Conclusions Tips was not only successful at reducing smoking-attributable morbidity and mortality but also was a highly cost-effective mass media intervention. PMID:25498550

Earned Media and Public Engagement With CDC’s "Tips From Former Smokers" Campaign: An Analysis of Online News and Blog Coverage

PubMed Central

Kornfield, Rachel; Szczypka, Glen; Vera, Lisa; Emery, Sherry

2015-01-01

Background In March 2012, the US Centers for Disease Control and Prevention (CDC) launched the first-ever paid national tobacco education campaign. At a cost of US $54 million, “Tips from Former Smokers” (Tips) ran for 3 months across multiple media, depicting the suffering experienced by smokers and their families in graphic detail. The potential impact and reach of the Tips campaign was not limited to that achieved through paid media placements. It was also potentially extended through “earned media”, including news and blog coverage of the campaign. Such coverage can shape public understanding of and facilitate public engagement with key health issues. Objective To better understand the contribution of earned media to the public’s engagement with health issues in the current news media environment, we examined the online “earned media” and public engagement generated by one national public health campaign. Methods We constructed a purposive sample of online media coverage of the CDC’s 2012 Tips from Former Smokers television campaign, focusing on 14 influential and politically diverse US news outlets and policy-focused blogs. We identified relevant content by combining campaign and website-specific keywords for 4 months around the campaign release. Each story was coded for content, inclusion of multimedia, and measures of audience engagement. Results The search yielded 36 stories mentioning Tips, of which 27 were focused on the campaign. Story content between pieces was strikingly similar, with most stories highlighting the same points about the campaign’s content, cost, and potential impact. We saw notable evidence of audience engagement; stories focused on Tips generated 9547 comments, 8891 Facebook “likes”, 1027 tweets, and 505 story URL shares on Facebook. Audience engagement varied by story and site, as did the valence and relevance of associated audience comments. Comments were most oppositional on CNN and most supportive on Yahoo. Comment coding revealed approximately equal levels of opposition and support overall. We identified four common arguments among oppositional comments: government intrusion on personal behaviors, problematic allocation of governmental spending, questionable science, and challenges regarding campaign efficacy. Supportive comments tended to convey personal stories and emotions. Conclusions The Tips campaign received limited coverage on either online news or blog sources, but the limited number of stories generated engagement among online audiences. In addition to the content and volume of blog and news coverage, audience comments and websites’ mechanisms for sharing stories via social media are likely to determine the influence of online earned media. In order to facilitate meaningful evaluation of public health campaigns within the rapidly advancing media environment, there is a need for the public health community to build consensus regarding collection and assessment of engagement data. PMID:25604520

What Every New Media Specialist Needs to Know: These 10 Tips Can Help Your Career Get off to a Great Start

ERIC Educational Resources Information Center

Corbo, Donna; Sample, Candace

2010-01-01

It's not easy being a media specialist, especially if one is new to the profession or one has switched schools and is suddenly the "new kid on the block." This article offers 10 road-tested tips that will help every new media specialist not only survive, but also "thrive": (1) Learn the curriculum; (2) Document! Document! Document! (3) Smile and…

Helping Children with Disabilities Cope with Disaster and Traumatic Events

MedlinePlus

... disturbing media images. For Teachers and Other School Staff Helping students cope with media coverage of disasters: A fact sheet for teachers and school staff [PDF | 307 KB] This fact sheet provides an ...

Early warning of climate tipping points

NASA Astrophysics Data System (ADS)

Lenton, Timothy M.

2011-07-01

A climate 'tipping point' occurs when a small change in forcing triggers a strongly nonlinear response in the internal dynamics of part of the climate system, qualitatively changing its future state. Human-induced climate change could push several large-scale 'tipping elements' past a tipping point. Candidates include irreversible melt of the Greenland ice sheet, dieback of the Amazon rainforest and shift of the West African monsoon. Recent assessments give an increased probability of future tipping events, and the corresponding impacts are estimated to be large, making them significant risks. Recent work shows that early warning of an approaching climate tipping point is possible in principle, and could have considerable value in reducing the risk that they pose.

Cyberbullying Prevention and Intervention Efforts: Current Knowledge and Future Directions.

PubMed

Espelage, Dorothy L; Hong, Jun Sung

2017-06-01

Bullying is a serious public health concern that is associated with significant negative mental, social, and physical outcomes. Technological advances have increased adolescents' use of social media, and online communication platforms have exposed adolescents to another mode of bullying- cyberbullying. Prevention and intervention materials, from websites and tip sheets to classroom curriculum, have been developed to help youth, parents, and teachers address cyberbullying. While youth and parents are willing to disclose their experiences with bullying to their health care providers, these disclosures need to be taken seriously and handled in a caring manner. Health care providers need to include questions about bullying on intake forms to encourage these disclosures. The aim of this article is to examine the current status of cyberbullying prevention and intervention. Research support for several school-based intervention programs is summarised. Recommendations for future research are provided.

Fuels planning: science synthesis and integration; social issues fact sheet 12: Keys to successful collaboration

Treesearch

Christine Esposito

2006-01-01

Collaborating on fire and fuels management with a host of public and private partners may seem like an impossible undertaking, and presents many challenges. This fact sheet reviews tips for what to focus on as you embark on a collaborative fuels management project.Other...

College Women's Health

MedlinePlus

... the College Women's Social Media Kit! College Women's Social Media Toolkit Use the Social Media Toolkit to share health tips with your campus ... toolkit includes resources for young women including sample social media messages, flyers and blogs posts. NEW Social Media ...

Extended Glauert tip correction to include vortex rollup effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maniaci, David; Schmitz, Sven

Wind turbine loads predictions by blade-element momentum theory using the standard tip-loss correction have been shown to over-predict loading near the blade tip in comparison to experimental data. This over-prediction is theorized to be due to the assumption of light rotor loading, inherent in the standard tip-loss correction model of Glauert. A higher- order free-wake method, WindDVE, is used to compute the rollup process of the trailing vortex sheets downstream of wind turbine blades. Results obtained serve an exact correction function to the Glauert tip correction used in blade-element momentum methods. Lastly, it is found that accounting for the effectsmore » of tip vortex rollup within the Glauert tip correction indeed results in improved prediction of blade tip loads computed by blade-element momentum methods.« less

Extended Glauert tip correction to include vortex rollup effects

DOE PAGES

Maniaci, David; Schmitz, Sven

2016-10-03

Wind turbine loads predictions by blade-element momentum theory using the standard tip-loss correction have been shown to over-predict loading near the blade tip in comparison to experimental data. This over-prediction is theorized to be due to the assumption of light rotor loading, inherent in the standard tip-loss correction model of Glauert. A higher- order free-wake method, WindDVE, is used to compute the rollup process of the trailing vortex sheets downstream of wind turbine blades. Results obtained serve an exact correction function to the Glauert tip correction used in blade-element momentum methods. Lastly, it is found that accounting for the effectsmore » of tip vortex rollup within the Glauert tip correction indeed results in improved prediction of blade tip loads computed by blade-element momentum methods.« less

Frictional behavior of atomically thin sheets: hexagonal-shaped graphene islands grown on copper by chemical vapor deposition.

PubMed

Egberts, Philip; Han, Gang Hee; Liu, Xin Z; Johnson, A T Charlie; Carpick, Robert W

2014-05-27

Single asperity friction experiments using atomic force microscopy (AFM) have been conducted on chemical vapor deposited (CVD) graphene grown on polycrystalline copper foils. Graphene substantially lowers the friction force experienced by the sliding asperity of a silicon AFM tip compared to the surrounding oxidized copper surface by a factor ranging from 1.5 to 7 over loads from the adhesive minimum up to 80 nN. No damage to the graphene was observed over this range, showing that friction force microscopy serves as a facile, high contrast probe for identifying the presence of graphene on Cu. Consistent with studies of epitaxially grown, thermally grown, and mechanically exfoliated graphene films, the friction force measured between the tip and these CVD-prepared films depends on the number of layers of graphene present on the surface and reduces friction in comparison to the substrate. Friction results on graphene indicate that the layer-dependent friction properties result from puckering of the graphene sheet around the sliding tip. Substantial hysteresis in the normal force dependence of friction is observed with repeated scanning without breaking contact with a graphene-covered region. Because of the hysteresis, friction measured on graphene changes with time and maximum applied force, unless the tip slides over the edge of the graphene island or contact with the surface is broken. These results also indicate that relatively weak binding forces exist between the copper foil and these CVD-grown graphene sheets.

Solid/melt interface studies of high-speed silicon sheet growth

NASA Technical Reports Server (NTRS)

Ciszek, T. F.

1984-01-01

Radial growth-rate anisotropies and limiting growth forms of point nucleated, dislocation-free silicon sheets spreading horizontally on the free surface of a silicon melt have been measured for (100), (110), (111), and (112) sheet planes. Sixteen-millimeter movie photography was used to record the growth process. Analysis of the sheet edges has lead to predicted geometries for the tip shape of unidirectional, dislocation-free, horizontally growing sheets propagating in various directions within the above-mentioned planes. Similar techniques were used to study polycrystalline sheets and dendrite propagation. For dendrites, growth rates on the order of 2.5 m/min and growth rate anisotropies on the order of 25 were measured.

Impact of 1.5°C global warming on the Greenland and Antarctic ice sheets

NASA Astrophysics Data System (ADS)

Ritz, Catherine; Pattyn, Frank

2017-04-01

For strengthening the global response to climate change, it is crucial to assess to what extent limiting global warming to low values may reduce the impacts on society. To tackle this issue, the IPCC has decided to provide a special report in 2018 on the impacts of global warming of 1.5°C above pre-industrial levels and related global greenhouse gas emission pathways. Ice sheets are well known contributors to sea level rise and many studies have aimed to provide projections of their future contribution in response to climate change, although the focus was often on worst-case scenarios. Here we propose to review the present knowledge of how the ice sheets could be affected in the case of a limited warming of 1.5°C to 2.0°C. We will review the various processes and feedbacks known to induce ice sheets vulnerability. They are different for Greenland, where we know that the surface mass balance plays a crucial role, and Antarctica where the major risk is marine ice sheet instability. One point of interest is to define, in terms of local forcing, the tipping points associated with these processes. We note that limiting global warming to 1.5°C may mean substantially more warming in the polar regions. This polar amplification can be assessed from experiments following the RCP2.6 scenario that have been carried out in recent (post IPCC AR5) studies. This scenario can be considered as an upper limit for 1.5°C. The final question concerns the long term (millennial) impact. There is a general consensus that there are tipping points both for Greenland and Antarctica, which potentially lead to irreversible mass loss. We will review the current knowledge of how long it takes to reach these tipping points and whether subsequent ice-sheet demise is, indeed, unstoppable.

Hover and Wind-Tunnel Testing of Shrouded Rotors for Improved Micro Air Vehicle Design

DTIC Science & Technology

2008-01-01

and the shroud surface pressure distributions. The uniformity of the wake was improved by the presence of the shrouds and by decreasing the blade tip...213 3.35 Effect of blade tip clearance on shrouded-rotor exit-plane wake profiles215 3.36 Effects of changing blade tip clearance on induced...Wright [139] developed a vortex wake model for heavily loaded ducted fans, in which the “inner vortex sheets [shed from the blades ] move at a different

Tubular graphite cones.

PubMed

Zhang, Guangyu; Jiang, Xin; Wang, Enge

2003-04-18

We report the synthesis of tubular graphite cones using a chemical vapor deposition method. The cones have nanometer-sized tips, micrometer-sized roots, and hollow interiors with a diameter ranging from about 2 to several tens of nanometers. The cones are composed of cylindrical graphite sheets; a continuous shortening of the graphite layers from the interior to the exterior makes them cone-shaped. All of the tubular graphite cones have a faceted morphology. The constituent graphite sheets have identical chiralities of a zigzag type across the entire diameter, imparting structural control to tubular-based carbon structures. The tubular graphite cones have potential for use as tips for scanning probe microscopy, but with greater rigidity and easier mounting than currently used carbon nanotubes.

User's manual for the National Water Information Systemof the U.S. Geological Survey Water-Quality System

USGS Publications Warehouse

Gellenbeck, Dorinda J.; Oblinger, Carolyn J.; Runkle, Donna L.; Schertz, Terry L.; Scott, Jonathon C.; Stoker, Yvonne E.; Taylor, Robert L.

2006-01-01

This user documentation is designed to be a reference for the Water-Quality System (QWDATA) within the National Water Information System (NWIS). For the new user, the 'Introduction' and 'Getting Started' sections are the recommended places to begin. The experienced user may want to go straight to the details provided in the program section (section 3). Code lists and some miscellaneous reference materials are provided in the Appendices. The last section, 'Tip Sheets,' is a collection of suggestions for accomplishing selected tasks, some of which are basic and some of which are advanced. Where appropriate, these Tip Sheets are referenced in the main text of the documentation.

User's manual for the National Water Information System of the U.S. Geological Survey (USGS), Water-quality System (QWDATA)

USGS Publications Warehouse

Gellenbeck, Dorinda; Oblinger, Carolyn J.; Runkle, Donna L.; Schertz, Terry L.; Scott, Jonathon C.; Taylor, Robert L.

2005-01-01

This user documentation is designed to be a reference for the Water-Quality System (QWDATA) within the National Water Information System (NWIS). For the new user, the 'Introduction' and 'Getting Started' sections are the recommended places to begin. The experienced user may want to go straight to the details provided in the program section (section 3). Code lists and some miscellaneous reference materials are provided in the Appendices. The last section, 'Tip Sheets,' is a collection of suggestions for accomplishing selected tasks, some of which are basic and some of which are advanced. Where appropriate, these Tip Sheets are referenced in the main text of the documentation.

A view from the terrace; ice-sheet dynamics during the Eocene Oligocene Transition climate tipping point

NASA Astrophysics Data System (ADS)

Scher, Howie; Bohaty, Steven; Huck, Claire

2017-04-01

Glaciation of Antarctica was the pièce de résistance of the shift in global climate that took place during the Eocene Oligocene Transition (EOT; ca. 34 Ma). The timing and progression of ice-sheet development is constrained by benthic foraminiferal d18O records and geochemical proxies for continental weathering from deep-sea sediment cores. The terrace interval is the roughly 500 kyr interval after the precursor glaciation at 34.2 Ma, when ice-sheet expansion reached a short-lived plateau prior to the coalescence of a continent-scale ice sheet at 33.7 Ma. The terrace interval appears to be the tipping point between greenhouse and icehouse climate states, however ice-sheet dynamics are poorly understood during this crucial time. We present evidence for rapid changes in the Nd isotopic composition of bottom waters bathing a sediment core on Maud Rise (ODP Site 689) during the terrace interval of the EOT. Three distinct excursions toward less radiogenic eNd values suggest either 1) changes in the flux of Antarctic weathering products into the Weddell Sea and/or 2) pulses of deep water production that brought shelf waters with the Antarctic Nd isotope fingerprint into contact with Maud Rise. Both interpretations support a scenario of expansion and contraction of the Antarctic ice sheet during the terrace interval.

Cyberbullying Prevention and Intervention Efforts: Current Knowledge and Future Directions

PubMed Central

Hong, Jun Sung

2016-01-01

Bullying is a serious public health concern that is associated with significant negative mental, social, and physical outcomes. Technological advances have increased adolescents’ use of social media, and online communication platforms have exposed adolescents to another mode of bullying—cyberbullying. Prevention and intervention materials, from websites and tip sheets to classroom curriculum, have been developed to help youth, parents, and teachers address cyberbullying. While youth and parents are willing to disclose their experiences with bullying to their health care providers, these disclosures need to be taken seriously and handled in a caring manner. Health care providers need to include questions about bullying on intake forms to encourage these disclosures. The aim of this article is to examine the current status of cyberbullying prevention and intervention. Research support for several school-based intervention programs is summarised. Recommendations for future research are provided. PMID:28562094

New magnetism research brings high-temp superconductivity applications

Science.gov Websites

Contacts Social Media Photos Videos Fact Sheets, Brochures and Reports Summer Science Writing Internship Contacts Social Media Photos Videos Fact Sheets, Brochures and Reports Summer Science Writing Internship New magnetism research brings high-temp superconductivity applications closer By Angela Hardin * April

Know Your School District: Tips for Parents. PACER Center ACTion Information Sheets. PHP-c112

ERIC Educational Resources Information Center

PACER Center, 2006

2006-01-01

Becoming familiar with the school district will help parents become active and involved partners in their child's education. Research has demonstrated that family involvement in children's education can boost their academic success. Knowing about the following areas, which are discussed in this information sheet, can help parental involvement at…

Wire Composition: Its Effect on Metal Disintegration and Particle Formation in Twin-Wire Arc-Spraying Process

NASA Astrophysics Data System (ADS)

Tillmann, W.; Abdulgader, M.

2013-03-01

The wire tips in twin-wire arc-spraying (TWAS) are heated in three different zones. A high-speed camera was used to observe the melting behavior, metal breakup, and particle formation under different operating conditions. In zone (I), the wire tips are melted (liquidus metal) and directly atomized in the form of smaller droplets. Their size is a function of the specific properties of the molten metal and the exerting aerodynamic forces. Zone (II) is directly beneath zone (I) and the origin of the extruded metal sheets at the wire tips. The extruded metal sheets in the case of cored wires are shorter than those observed while using solid wires. In this study, the effects of adjustable parameters and powder filling on melting behavior, particle formation, and process instability were revealed, and a comparison between solid and cored wires was made. The findings can improve the accuracy of the TWAS process modeling.

A fracture criterion for widespread cracking in thin-sheet aluminum alloys

NASA Technical Reports Server (NTRS)

Newman, J. C., Jr.; Dawicke, D. S.; Sutton, M. A.; Bigelow, C. A.

1993-01-01

An elastic-plastic finite-element analysis was used with a critical crack-tip-opening angle (CTOA) fracture criterion to model stable crack growth in thin-sheet 2024-T3 aluminum alloy panels with single and multiple-site damage (MSD) cracks. Comparisons were made between critical angles determined from the analyses and those measured with photographic methods. Calculated load against crack extension and load against crack-tip displacement on single crack specimens agreed well with test data even for large-scale plastic deformations. The analyses were also able to predict the stable tearing behavior of large lead cracks in the presence of stably tearing MSD cracks. Small MSD cracks significantly reduced the residual strength for large lead cracks.

Electrostatic force spectroscopy revealing the degree of reduction of individual graphene oxide sheets.

PubMed

Shen, Yue; Wang, Ying; Zhou, Yuan; Hai, Chunxi; Hu, Jun; Zhang, Yi

2018-01-01

Electrostatic force spectroscopy (EFS) is a method for monitoring the electrostatic force microscopy (EFM) phase with high resolution as a function of the electrical direct current bias applied either to the probe or sample. Based on the dielectric constant difference of graphene oxide (GO) sheets (reduced using various methods), EFS can be used to characterize the degree of reduction of uniformly reduced one-atom-thick GO sheets at the nanoscale. In this paper, using thermally or chemically reduced individual GO sheets on mica substrates as examples, we characterize their degree of reduction at the nanoscale using EFS. For the reduced graphene oxide (rGO) sheets with a given degree of reduction (sample n), the EFS curve is very close to a parabola within a restricted area. We found that the change in parabola opening direction (or sign the parabola opening value) indicates the onset of reduction on GO sheets. Moreover, the parabola opening value, the peak bias value (tip bias leads to the peak or valley EFM phases) and the EFM phase contrast at a certain tip bias less than the peak value can all indicate the degree of reduction of rGO samples, which is positively correlated with the dielectric constant. In addition, we gave the ranking of degree for reduction on thermally or chemically reduced GO sheets and evaluated the effects of the reducing conditions. The identification of the degree of reduction of GO sheets using EFS is important for reduction strategy optimization and mass application of GO, which is highly desired owing to its mechanical, thermal, optical and electronic applications. Furthermore, as a general and quantitative technique for evaluating the small differences in the dielectric properties of nanomaterials, the EFS technique will extend and facilitate its nanoscale electronic devices applications in the future.

Complete Soil-Structure Interaction (SSI) Analyses of I-walls Embedded in Level Ground During Flood Loading

DTIC Science & Technology

2012-09-01

at the ground surface el 0 ft versus water elevation...sheet pile at the ground surface . ................ 62  Figure 3.24. Total displacements for a water elevation of 16.5 ft and a gap tip elevation of -11...103  Figure 4.19. Relative horizontal displacements of the sheet pile at the ground surface

CSC Tip Sheets: Working with Institutional Partners

EPA Pesticide Factsheets

Partner with organizations, such as other jurisdictions, utilities, complementary programs, community-based organizations, and others, can help you implement your program and achieve your collective goals.

Cessation Outcomes Among Quitline Callers in Three States During a National Tobacco Education Campaign.

PubMed

Vickerman, Katrina A; Zhang, Lei; Malarcher, Ann; Mowery, Paul; Nash, Chelsea

2015-07-16

Antismoking mass media campaigns, such as the Centers for Disease Control and Prevention's Tips from Former Smokers (Tips) campaign, increase the number of tobacco users calling tobacco quitlines. Few studies have investigated long-term tobacco use cessation for callers during antismoking media campaigns. Studies have suggested that callers during campaigns may be less committed to quitting and have lower quit rates. This study examines tobacco user cessation outcomes 7 months after quitline enrollment during the 2012 Tips campaign (March 19 through June 10, 2012). We analyzed data for 715 tobacco users who enrolled in the Nebraska, North Carolina, or Texas state quitline multiple-call programs during the 2012 Tips campaign and responded to a 7-month postenrollment survey (38.5% survey response rate). We used multivariable logistic regression analyses to determine whether 7-day and 30-day point prevalence abstinence rates 7 months after enrollment were related to level of exposure to the campaign. In multivariable models, only lower nicotine dependence and higher call completion were associated with higher odds of 7-day and 30-day abstinence 7 months after enrollment. Tips campaign exposure was not associated with abstinence. Once enrolled in quitline counseling, quitline callers achieved similar outcomes regardless of Tips campaign exposure levels. While the campaign did not appear to directly affect odds of tobacco abstinence through quitlines, antismoking mass media campaigns such as Tips are valuable in increasing tobacco users' exposure to quitlines and thus increasing their likelihood of making a quit attempt and eventually achieving tobacco abstinence.

Global Coastal Exposure due to Sea-level Rise beyond Tipping Points with Multiple Warming Pathways

NASA Astrophysics Data System (ADS)

Tawatari, R.; Iseri, Y.; Kiguchi, M.; Kanae, S.

2016-12-01

Sea-level is observed and estimated to continue rising. In the future, the rise could be abrupt and irreversible in century to millennial timescale even if we conduct strong reduction of greenhouse gas emission. Greenland ice sheet and West Antarctic ice sheet are considered as attributable climate systems which would significantly enhance presently-projected sea-level rise by several meters if global mean temperature passes certain "Tipping points" which would exist around +1-5 degree Celsius above present temperature (1980-1999 average). Therefore, vulnerable coastal low-lying area, especially small islands, deltas or poor developing countries, would suffer from semi-permanent inundation and forced to counteract due to the enhanced sea-level rise. This study estimate range of sea-level rise until the year 2300 and 3000 considering excess of tipping points with using multiple levels of temperature scenarios which consist of excess tipping points and non-excess tipping points pathways. We extract state-of-the-art knowledge of tipping elements from paper reviewing to express reasonable relationship between temperature and abruptly-changing sea-level transition across the ages. This study also calculate coastal exposure globally as affected population, area and asset below the estimated sea-level for each countries with overlaying 30 arc-second gridded topography, population distribution and the sea-level. The result indicates which country would be critically affected if we follow overshooting pathways. Furthermore, this study visualize uncertain coastal exposure due to sea-level rise in the future from the multiple warming pathways. This estimation of possible future beyond tipping point would be useful information for decision-makers to establish new planning of defense, migration or mitigation for the future societies.

Tips for Kids: Lower Your Risk for Type 2 Diabetes

ERIC Educational Resources Information Center

US Department of Health and Human Services, 2005

2005-01-01

Today, more kids have type 2 diabetes than ever before. This colorful, easy-to-read tip sheet encourages young people to take steps to lower their risk for type 2 diabetes. A list of warning signs and a healthy eating guide is offered, along with a list of websites to learn more. [This brochure was prepared by the Department of Health and Human…

Increasing the dose of television advertising in a national antismoking media campaign: results from a randomised field trial

PubMed Central

McAfee, Tim; Davis, Kevin C; Shafer, Paul; Patel, Deesha; Alexander, Robert; Bunnell, Rebecca

2017-01-01

Background While antismoking media campaigns have demonstrated effectiveness, less is known about the country-level effects of increased media dosing. The 2012 US Tips From Former Smokers (Tips) campaign generated approximately 1.6 million quit attempts overall; however, the specific dose–response from the campaign was only assessed by self-report. Objective Assess the impact of higher ad exposure during the 2013 Tips campaign on quit-related behaviours and intentions, campaign awareness, communication about campaign, and disease knowledge. Methods A 3-month national media buy was supplemented within 67 (of 190) randomly selected local media markets. Higher-dose markets received media buys 3 times that of standard-dose markets. We compared outcomes of interest using data collected via web-based surveys from nationally representative, address-based probability samples of 5733 cigarette smokers and 2843 non-smokers. Results In higher-dose markets, 87.2% of smokers and 83.9% of non-smokers recalled television campaign exposure versus 75.0% of smokers and 73.9% of non-smokers in standard-dose markets. Among smokers overall, the relative quit attempt rate was 11% higher in higher-dose markets (38.8% vs 34.9%; p<0.04). The higher-dose increase was larger in African-Americans (50.9% vs 31.8%; p<0.01). Smokers in higher-dose markets without a mental health condition, with a chronic health condition, or with only some college education made quit attempts at a higher rate than those in standard-dose markets. Non-smokers in higher-dose markets were more likely to talk with family or friends about smoking dangers (43.1% vs 35.7%; p<0.01) and had greater knowledge of smoking-related diseases. Conclusions The US 2013 Tips antismoking media campaign compared standard and higher doses by randomisation of local media markets. Results demonstrate the effectiveness of a higher dose for engaging non-smokers and further increasing quit attempts among smokers, especially African-Americans. PMID:26678518

Scabies

MedlinePlus

... too. Wash clothing, sheets, and towels in hot water and dry on a hot setting. Put stuffed animals and other items that ... Sexually Transmitted Diseases (STDs) Tips for Taking Care of Your Skin ...

Food Safety

MedlinePlus

... Price Tag Read the Food Label Kitchen Timesavers Cooking for Your Family Tasty & Low-Cost Recipes Sample 2-Week Menus Resources for Professionals MyPlate Tip Sheets Print Materials Infographics 5 Ways ...

Media--it takes more than flipping a switch.

PubMed

Miller, J

1980-01-01

Choosing the right audiovisual media for a health education program involves a variety of considerations, not the least of which is budget. The following article offers tips on making an informed, intelligent selection of media programs.

Ovarian Cancer Fact Sheet

MedlinePlus

... information Stay Connected Blog Contact us Media inquiries Social media About Us Who we are What we do ... information Stay Connected Blog Contact us Media inquiries Social media Subscribe to receive OWH updates Submit HHS Non- ...

Uterine Fibroids Fact Sheet

MedlinePlus

... information Stay Connected Blog Contact us Media inquiries Social media About Us Who we are What we do ... information Stay Connected Blog Contact us Media inquiries Social media Subscribe to receive OWH updates Submit HHS Non- ...

Myasthenia Gravis Fact Sheet

MedlinePlus

... information Stay Connected Blog Contact us Media inquiries Social media About Us Who we are What we do ... information Stay Connected Blog Contact us Media inquiries Social media Subscribe to receive OWH updates Submit HHS Non- ...

Finite-span rotating wings: three-dimensional vortex formation and variations with aspect ratio

NASA Astrophysics Data System (ADS)

Carr, Z. R.; Chen, C.; Ringuette, M. J.

2013-02-01

We investigate experimentally the effect of aspect ratio ( [InlineMediaObject not available: see fulltext.] ) on the time-varying, three-dimensional flow structure of flat-plate wings rotating from rest at 45° angle of attack. Plates of [InlineMediaObject not available: see fulltext.] = 2 and 4 are tested in a 50 % by mass glycerin-water mixture, with a total rotation of ϕ = 120° and a matched tip Reynolds number of 5,000. The time-varying, three-component volumetric velocity field is reconstructed using phase-locked, phase-averaged stereoscopic digital particle image velocimetry in multiple, closely-spaced chordwise planes. The vortex structure is analyzed using the {Q}-criterion, helicity density, and spanwise quantities. For both [InlineMediaObject not available: see fulltext.] s, the flow initially consists of a connected and coherent leading-edge vortex (LEV), tip vortex (TV), and trailing-edge vortex (TEV) loop; the LEV increases in size with span and tilts aft. Smaller, discrete vortices are present in the separated shear layers at the trailing and tip edges, which wrap around the primary TEV and TV. After about ϕ = 20°, the outboard-span LEV lifts off the plate and becomes arch-like. A second, smaller LEV and the formation of corner vortex structures follow. For [InlineMediaObject not available: see fulltext.] = 4, the outboard LEV moves farther aft, multiple LEVs form ahead of it, and after about ϕ = 50° a breakdown of the lifted-off LEV and the TV occurs. However, for [InlineMediaObject not available: see fulltext.] = 2, the outboard LEV lift-off is not progressive, and the overall LEV-TV flow remains more coherent and closer to the plate, with evidence of breakdown late in the motion. Inboard of about 50 % span, the [InlineMediaObject not available: see fulltext.] = 4 LEV is stable for the motion duration. Up to approximately 60 % span, the [InlineMediaObject not available: see fulltext.] = 2 LEV is distinct from the TV and is similarly stable. The [InlineMediaObject not available: see fulltext.] = 2 LEV exhibits substantially higher spanwise vorticity and velocity. The latter possesses a "four-lobed" distribution at the periphery of the LEV core having adjacent positive (outboard) and negative (inboard) components, corresponding to a helical streamline structure. Both [InlineMediaObject not available: see fulltext.] s show substantial root-to-tip velocity aft of the stable LEV, which drives outboard spanwise vorticity flux; flux toward the root is also present in the front portion of the LEV. For [InlineMediaObject not available: see fulltext.] = 2, there is a strong flux of spanwise vorticity from the outboard LEV to the tip, which may mitigate LEV lift-off and is not found for [InlineMediaObject not available: see fulltext.] = 4. The TV circulation for each [InlineMediaObject not available: see fulltext.] is similar in magnitude and growth when plotted versus the chord lengths travelled by the tip, prior to breakdown. Streamwise vorticity due to the TV induces high spanwise velocity, and for [InlineMediaObject not available: see fulltext.] = 2, the tilted LEV creates further streamwise vorticity which corresponds well to spanwise-elongated regions of spanwise velocity. For [InlineMediaObject not available: see fulltext.] = 2, the TV influences a relatively greater portion of the span and is more coherent at later times, which coupled with the tilted LEV strongly contributes to the higher overall spanwise velocity and vorticity flux.

The singing vortex.

PubMed

Arndt, R; Pennings, P; Bosschers, J; van Terwisga, T

2015-10-06

Marine propellers display several forms of cavitation. Of these, propeller-tip vortex cavitation is one of the important factors in propeller design. The dynamic behaviour of the tip vortex is responsible for hull vibration and noise. Thus, cavitation in the vortices trailing from tips of propeller blades has been studied extensively. Under certain circumstances cavitating vortices have been observed to have wave-like disturbances on the surfaces of vapour cores. Intense sound at discrete frequencies can result from a coupling between tip vortex disturbances and oscillating sheet cavitation on the surfaces of the propeller blades. This research article focuses on the dynamics of vortex cavitation and more in particular on the energy and frequency content of the radiated pressures.

The singing vortex

PubMed Central

Arndt, R.; Pennings, P.; Bosschers, J.; van Terwisga, T.

2015-01-01

Marine propellers display several forms of cavitation. Of these, propeller-tip vortex cavitation is one of the important factors in propeller design. The dynamic behaviour of the tip vortex is responsible for hull vibration and noise. Thus, cavitation in the vortices trailing from tips of propeller blades has been studied extensively. Under certain circumstances cavitating vortices have been observed to have wave-like disturbances on the surfaces of vapour cores. Intense sound at discrete frequencies can result from a coupling between tip vortex disturbances and oscillating sheet cavitation on the surfaces of the propeller blades. This research article focuses on the dynamics of vortex cavitation and more in particular on the energy and frequency content of the radiated pressures. PMID:26442147

Pregnancy Weight Gain Calculator

MedlinePlus

... Price Tag Read the Food Label Kitchen Timesavers Cooking for Your Family Tasty & Low-Cost Recipes Sample 2-Week Menus Resources for Professionals MyPlate Tip Sheets Print Materials Infographics 5 Ways ...

CSC Tip Sheets: Working with Corporations

EPA Pesticide Factsheets

Programs can work with corporations to reduce companies’ greenhouse gas emissions and energy use, as well as create partnerships to reach employees and the community with local sustainability program offerings.

Breathing Easy

EPA Pesticide Factsheets

This fact sheet provides practical information and guidance to auto refinish shops on proper ventilation of paint mixing rooms, including ventilation system basics and diagrams, risk reduction ideas, common mistakes, tips, and design considerations.

User’s manual for the National Water Information System of the U.S. Geological Survey: Water-Quality System

USGS Publications Warehouse

Dupré, David H.; Scott, Jonathon C.; Clark, Melanie L.; Canova, Michael G.; Stoker, Yvonne E.

2013-01-01

This user documentation is designed to be a reference for the quality of water (QW) programs within the National Water Information System (NWIS). If you are a new user, the “Introduction” and “Getting Started” sections may be the right place for you to start. If you are an experienced user, you may want to go straight to the details provided in the “Program” section (section 3). Code lists and some miscellaneous reference materials are provided in the Appendices. The last section, “Tip Sheets,” is a collection of suggestions for accomplishing selected tasks, some of which are basic and some are advanced. These tip sheets are referenced in the main text of the documentation where appropriate.

Daily Food Plan for Moms

MedlinePlus

... Price Tag Read the Food Label Kitchen Timesavers Cooking for Your Family Tasty & Low-Cost Recipes Sample 2-Week Menus Resources for Professionals MyPlate Tip Sheets Print Materials Infographics 5 Ways ...

Why Take a Prenatal Supplement?

MedlinePlus

... Price Tag Read the Food Label Kitchen Timesavers Cooking for Your Family Tasty & Low-Cost Recipes Sample 2-Week Menus Resources for Professionals MyPlate Tip Sheets Print Materials Infographics 5 Ways ...

Glacial uplift: fluid injection beneath an elastic sheet on a poroelastic substrate

NASA Astrophysics Data System (ADS)

Neufeld, Jerome; Hewitt, Duncan; Chini, Greg

2016-11-01

Supraglacial lakes can drain to the base of glaciers extremely rapidly, causing localised uplift of the surrounding glacier and affecting its sliding velocity. The means by which large volumes of drained water interact with and leak into the subglacial hydrological system is unclear, as is the role of the basal till. A theoretical study of the spread of fluid injected below an elastic sheet (the ice) is presented, where the ice lies above, and initially compresses, a deformable poroelastic layer. As pressurized fluid is injected, the deformable layer swells to accommodate more fluid. If sufficient fluid is injected, a 'blister' of fluid forms above the layer, causing the overburden to lift off the base. The flow is controlled by the local pressure drop across the tip of this blister, which depends subtly on both the flow of fluid through the porous layer below the tip, and on poroelastic deformation in the till ahead of the tip. The spreading behaviour and dependence on key parameters is analysed. Predictions of the model are compared to field measurements of uplift from draining glacial lakes in Greenland.

ESTIMATION OF EFFECTIVE SHEAR STRESS WORKING ON FLAT SHEET MEMBRANE USING FLUIDIZED MEDIA IN MBRs

NASA Astrophysics Data System (ADS)

Zaw, Hlwan Moe; Li, Tairi; Nagaoka, Hiroshi; Mishima, Iori

This study was aimed at estimating effective shear stress working on flat sheet membrane by the addition of fluidized media in MBRs. In both of laboratory-scale aeration tanks with and without fluidized media, shear stress variations on membrane surface and water phase velocity variations were measured and MBR operation was conducted. For the evaluation of the effective shear stress working on membrane surface to mitigate membrane surface, simulation of trans-membrane pressure increase was conducted. It was shown that the time-averaged absolute value of shear stress was smaller in the reactor with fluidized media than without fluidized media. However, due to strong turbulence in the reactor with fluidized media caused by interaction between water-phase and media and also due to the direct interaction between membrane surface and fluidized media, standard deviation of shear stress on membrane surface was larger in the reactor with fluidized media than without media. Histograms of shear stress variation data were fitted well to normal distribution curves and mean plus three times of standard deviation was defined to be a maximum shear stress value. By applying the defined maximum shear stress to a membrane fouling model, trans-membrane pressure curve in the MBR experiment was simulated well by the fouling model indicting that the maximum shear stress, not time-averaged shear stress, can be regarded as an effective shear stress to prevent membrane fouling in submerged flat-sheet MBRs.

Light-sheet generation in inhomogeneous media using self-reconstructing beams and the STED-principle.

PubMed

Gohn-Kreuz, Cristian; Rohrbach, Alexander

2016-03-21

Self-reconstruction of Bessel beams in inhomogeneous media is beneficial in light-sheet based microscopy. Although the beam's ring system enables propagation stability, the resulting image contrast is reduced. Here, we show that by a combination of two self-reconstructing beams with different orbital angular momenta it is possible to inhibit fluorescence from the ring system by using stimulated emission depletion (STED) even in strongly scattering media. Our theoretical study shows that the remaining fluorescence γ depends non-linearly on the beams' relative radial and orbital angular momenta. For various scattering media we demonstrate that γ remains remarkably stable over long beam propagation distances.

Five Tips to Help Prevent Infections

MedlinePlus

... Information For… Media Policy Makers 5 Tips to Help Prevent Infections Language: English (US) Español (Spanish) Recommend ... Makers Language: English (US) Español (Spanish) File Formats Help: How do I view different file formats (PDF, ...

Sun and Sjogren's Syndrome

MedlinePlus

... California, for authoring this Patient Education Sheet. Ultraviolet (UV) radiation emitted from the sun and other light ... autoantibody SSA/or Ro. To avoid reactions to UV light, try the following tips: Protect your skin ...

Smart Shopping for Veggies and Fruits

MedlinePlus

... Price Tag Read the Food Label Kitchen Timesavers Cooking for Your Family Tasty & Low-Cost Recipes Sample 2-Week Menus Resources for Professionals MyPlate Tip Sheets Print Materials Infographics 5 Ways ...

Benefits of social media for nurses and service users.

PubMed

Betton, Victoria is deputy; Tomlinson, Victoria

People with mental health problems are increasingly using social media channels as part of their recovery and to improve their lives. This article discusses social media and how it can be used to complement healthcare, offers useful tips on using social media, and explores case studies for nurses to use in clinical practice.

Increases in quitline calls and smoking cessation website visitors during a national tobacco education campaign--March 19-June 10, 2012.

PubMed

2012-08-31

Mass media campaigns and telephone quitlines are effective in increasing cessation rates among cigarette smokers. During March 19-June 10, 2012, CDC aired Tips from Former Smokers (TIPS), the first federally funded, nationwide, paid-media tobacco education campaign in the United States. The TIPS campaign featured former smokers talking about their experiences living with diseases caused by smoking. The campaign was primarily intended to encourage adult smokers aged 18-54 years to quit by making them aware of the health damage caused by smoking and letting them know that they could call the telephone quitline portal 1-800-QUIT-NOW or visit the National Cancer Institute (NCI) smoking cessation website (http://www.smokefree.gov) if they needed free help to quit. The campaign included advertising on national and local cable television, local radio, online media, and billboards, and in movie theaters, transit venues, and print media. To determine the effects of the TIPS campaign on weekly quitline call volume and weekly unique visitors to the cessation website, CDC analyzed call and visitor data immediately before, during, and immediately after the campaign period and compared them with data from the corresponding weeks in 2011. This report summarizes the results of that analysis, which found that the number of weekly calls to the quitline from the 50 states, the District of Columbia, Guam, and Puerto Rico increased 132% (207,519 additional calls) during the TIPS campaign, and the number of unique visitors to the cessation website increased 428% (510,571 additional unique visitors). These results indicate that many smokers are interested in quitting and learning more about cessation assistance, and will respond to motivational messages that include an offer of help.

Tip-leakage cavitation in the clearance of a 2D hydrofoil with fillets: high-speed visualization and PIV/PTV measurements

NASA Astrophysics Data System (ADS)

Zapryagaev, Ivan I.; Timoshevskiy, Mikhail V.; Pervunin, Konstantin S.

2017-09-01

Tip-clearance cavitation is one of the most aggressive forms of cavitation as it can cause surface erosion of hydraulic machinery elements and, as a result, their fatigue damage and disturb designed operating conditions. At present, the literature lacks for detailed experimental data on the inception and development of this type of cavitation at various flow conditions. In the paper, a tip-leakage cavitation occurring in the clearance between an end face of a 2D hydrofoil (a scaled-down model of guide vanes (GV) of a Francis turbine) and a transparent wall of the test section was studied. The experiments were carried out for different cavitating regimes on the cavitation number and two attack angles of 3° and 9°, with the gap size (tip clearance width) varied in the range from 0.4 to 0.8 mm. In order to determine the cavitation inception conditions and investigate the dynamics of the tip-leakage cavitation, a high-speed visualization was applied. A modified PIV/PTV technique with a diverging laser beam instead of a laser light sheet was used to measure the mean velocity distributions within the gap. It was shown that the cavitation pattern on the suction side of the GV model impacts the dynamics of the leakage flow in the gap but does not affect the sheet cavity formed close to the foil leading edge in the clearance as well as its size and dynamics. When the gap size is increased, the tip-leakage cavitation initiates at higher cavitation numbers or, in other words, conditions for the cavitation occurrence become more favorable.

A Transient Initialization Routine of the Community Ice Sheet Model for the Greenland Ice Sheet

NASA Astrophysics Data System (ADS)

van der Laan, Larissa; van den Broeke, Michiel; Noël, Brice; van de Wal, Roderik

2017-04-01

The Community Ice Sheet Model (CISM) is to be applied in future simulations of the Greenland Ice Sheet under a range of climate change scenarios, determining the sensitivity of the ice sheet to individual climatic forcings. In order to achieve reliable results regarding ice sheet stability and assess the probability of future occurrence of tipping points, a realistic initial ice sheet geometry is essential. The current work describes and evaluates the development of a transient initialization routine, using NGRIP 18O isotope data to create a temperature anomaly field. Based on the latter, surface mass balance components runoff and precipitation are perturbed for the past 125k years. The precipitation and runoff fields originate from a downscaled 1 km resolution version of the regional climate model RACMO2.3 for the period 1961-1990. The result of the initialization routine is a present-day ice sheet with a transient memory of the last glacial-interglacial cycle, which will serve as the future runs' initial condition.

Safe Kids Worldwide

MedlinePlus

... Recalls Media Center Blog Videos Newsletter facebook twitter instagram pinterest gplus youtube Search Menu Why It Matters ... Recalls Media Center Blog Videos Newsletter facebook twitter instagram pinterest gplus youtube Sign up for quick tips ...

CSC Tip Sheets: Action Checklists

EPA Pesticide Factsheets

Learn how to use action checklists to motivate behavior change by providing a clear and concise list of activities that community members and organizations can use to reduce their carbon footprint and achieve other sustainability goals.

ChooseMyPlate.gov

MedlinePlus

... Resources for Students Resources for Adults Resources for Professionals Multi-Language Check Out Our Online Tools EATING ON A BUDGET MYPLATE TIP SHEETS MYPLATE QUIZZES SUPERTRACKER WHAT'S COOKING Check Out Our Online Tools Eating on a ...

Children with Special Health Care Needs

MedlinePlus

... to the Hospital Heroes On Medicine's Front Line Observation Emergency Care Fact Sheet Health & Safety Tips Campaigns ... to all caregivers of children, such as babysitters, teachers, and school nurses. Resources Emergency Care For You ...

Increasing the dose of television advertising in a national antismoking media campaign: results from a randomised field trial.

PubMed

McAfee, Tim; Davis, Kevin C; Shafer, Paul; Patel, Deesha; Alexander, Robert; Bunnell, Rebecca

2017-01-01

While antismoking media campaigns have demonstrated effectiveness, less is known about the country-level effects of increased media dosing. The 2012 US Tips From Former Smokers (Tips) campaign generated approximately 1.6 million quit attempts overall; however, the specific dose-response from the campaign was only assessed by self-report. Assess the impact of higher ad exposure during the 2013 Tips campaign on quit-related behaviours and intentions, campaign awareness, communication about campaign, and disease knowledge. A 3-month national media buy was supplemented within 67 (of 190) randomly selected local media markets. Higher-dose markets received media buys 3 times that of standard-dose markets. We compared outcomes of interest using data collected via web-based surveys from nationally representative, address-based probability samples of 5733 cigarette smokers and 2843 non-smokers. In higher-dose markets, 87.2% of smokers and 83.9% of non-smokers recalled television campaign exposure versus 75.0% of smokers and 73.9% of non-smokers in standard-dose markets. Among smokers overall, the relative quit attempt rate was 11% higher in higher-dose markets (38.8% vs 34.9%; p<0.04). The higher-dose increase was larger in African-Americans (50.9% vs 31.8%; p<0.01). Smokers in higher-dose markets without a mental health condition, with a chronic health condition, or with only some college education made quit attempts at a higher rate than those in standard-dose markets. Non-smokers in higher-dose markets were more likely to talk with family or friends about smoking dangers (43.1% vs 35.7%; p<0.01) and had greater knowledge of smoking-related diseases. The US 2013 Tips antismoking media campaign compared standard and higher doses by randomisation of local media markets. Results demonstrate the effectiveness of a higher dose for engaging non-smokers and further increasing quit attempts among smokers, especially African-Americans. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Our Children Are Hurting: Fact Sheet on the Disproportionate Involvement of Indian Young People in the Juvenile Justice and Child Welfare Systems in Ontario, 1981-1982.

ERIC Educational Resources Information Center

Jolly, Stan

This fact sheet documents the disturbing overrepresentation of status Indian youth in the juvenile justice and child welfare systems of Ontario (Canada). However, the information represents only the tip of the iceberg. Data relate solely to children and youth whose parents resided on an Indian reserve; who were dealt with by the family court (not…

A line scanned light-sheet microscope with phase shaped self-reconstructing beams.

PubMed

Fahrbach, Florian O; Rohrbach, Alexander

2010-11-08

We recently demonstrated that Microscopy with Self-Reconstructing Beams (MISERB) increases both image quality and penetration depth of illumination beams in strongly scattering media. Based on the concept of line scanned light-sheet microscopy, we present an add-on module to a standard inverted microscope using a scanned beam that is shaped in phase and amplitude by a spatial light modulator. We explain technical details of the setup as well as of the holograms for the creation, positioning and scaling of static light-sheets, Gaussian beams and Bessel beams. The comparison of images from identical sample areas illuminated by different beams allows a precise assessment of the interconnection between beam shape and image quality. The superior propagation ability of Bessel beams through inhomogeneous media is demonstrated by measurements on various scattering media.

Near wakes of advanced turbopropellers

NASA Technical Reports Server (NTRS)

Hanson, D. B.; Patrick, W. P.

1989-01-01

The flow in the wake of a model single rotation Prop-Fan rotor operating in a wind tunnel was traversed with a hot-wire anemometer system designed to determine the 3 periodic velocity components. Special data acquisition and data reduction methods were required to deal with the high data frequency, narrow wakes, and large fluctuating air angles in the tip vortex region. The model tip helical Mach number was 1.17, simulating the cruise condition. Although the flow field is complex, flow features such as viscous velocity defects, vortex sheets, tip vortices, and propagating acoustic pulses are clearly identified with the aid of a simple analytical wake theory.

Association between Media Doses of the "Tips from Former Smokers" Campaign and Cessation Behaviors and Intentions to Quit among Cigarette Smokers, 2012-2015

ERIC Educational Resources Information Center

Davis, Kevin C.; Patel, Deesha; Shafer, Paul; Duke, Jennifer; Glover-Kudon, Rebecca; Ridgeway, William; Cox, Shanna

2018-01-01

Background: Since 2012, the Centers for Disease Control and Prevention (CDC) has implemented "Tips From Former Smokers" ("Tips"), the first federally funded tobacco education campaign in the United States. To date, there are no evaluations of its long-term impact. Aims: To assess the impact of varied doses of the…

Theoretical study of carbon-based tips for scanning tunnelling microscopy.

PubMed

González, C; Abad, E; Dappe, Y J; Cuevas, J C

2016-03-11

Motivated by recent experiments, we present here a detailed theoretical analysis of the use of carbon-based conductive tips in scanning tunnelling microscopy. In particular, we employ ab initio methods based on density functional theory to explore a graphitic, an amorphous carbon and two diamond-like tips for imaging with a scanning tunnelling microscope (STM), and we compare them with standard metallic tips made of gold and tungsten. We investigate the performance of these tips in terms of the corrugation of the STM images acquired when scanning a single graphene sheet. Moreover, we analyse the impact of the tip-sample distance and show that it plays a fundamental role in the resolution and symmetry of the STM images. We also explore in depth how the adsorption of single atoms and molecules in the tip apexes modifies the STM images and demonstrate that, in general, it leads to an improved image resolution. The ensemble of our results provides strong evidence that carbon-based tips can significantly improve the resolution of STM images, as compared to more standard metallic tips, which may open a new line of research in scanning tunnelling microscopy.

Disaster Distress Helpline

MedlinePlus

... Tips Anniversaries and Trigger Events Types of Disasters Social Media and Disasters Español Contact Us Disaster Distress Helpline ... information if you wish to receive a reply. Social media inquiries . Email us with questions about the Disaster ...

Winter Weather Frequently Asked Questions

MedlinePlus

... Hot Weather Tips Warning Signs and Symptoms FAQs Social Media How to Stay Cool Missouri Cooling Centers Extreme ... PSAs for Disasters Resources for Emergency Health Professionals Social Media Health and Safety Concerns for All Disasters Animals ...

Winter Weather: Outdoor Safety

MedlinePlus

... Hot Weather Tips Warning Signs and Symptoms FAQs Social Media How to Stay Cool Missouri Cooling Centers Extreme ... PSAs for Disasters Resources for Emergency Health Professionals Social Media Health and Safety Concerns for All Disasters Animals ...

Insurance Discounts: Traffic Safety Tips

DOT National Transportation Integrated Search

1996-01-01

This fact sheet, NHTSA Facts: Summer 1996, discusses automobile insurance discounts. It relates how to obtain a discount, and details what factors can influence insurance premiums. It notes that discounts for safety features vary from insurance compa...

Tip Sheets

Science.gov Websites

United States Census Bureau Topics Population Latest Information Age and Sex Ancestry Children Mobility Population Estimates Population Projections Race Veterans Economy Latest Information Portal Other Economic Programs Business Latest Information Business Characteristics Classification Codes

Sharpen Your Edge on Choral Competition.

ERIC Educational Resources Information Center

Morgan, John; Burrows, Bill

1981-01-01

The authors present choral contest/music festival performance tips which they have gleaned from adjudication sheets, judges' notes, and directors' comments. They include ideas on such topics as intonation, musical selections, rehearsal, balance, and staging. (SJL)

CSC Tip Sheets: Working with Students

EPA Pesticide Factsheets

Work with students, individually or in teams, who are a volunteer workforce that offers resources to implement projects. In turn, these students are given a valuable hands-on learning experience, academic credit, and a career boost.

Tipping elements in the Arctic marine ecosystem.

PubMed

Duarte, Carlos M; Agustí, Susana; Wassmann, Paul; Arrieta, Jesús M; Alcaraz, Miquel; Coello, Alexandra; Marbà, Núria; Hendriks, Iris E; Holding, Johnna; García-Zarandona, Iñigo; Kritzberg, Emma; Vaqué, Dolors

2012-02-01

The Arctic marine ecosystem contains multiple elements that present alternative states. The most obvious of which is an Arctic Ocean largely covered by an ice sheet in summer versus one largely devoid of such cover. Ecosystems under pressure typically shift between such alternative states in an abrupt, rather than smooth manner, with the level of forcing required for shifting this status termed threshold or tipping point. Loss of Arctic ice due to anthropogenic climate change is accelerating, with the extent of Arctic sea ice displaying increased variance at present, a leading indicator of the proximity of a possible tipping point. Reduced ice extent is expected, in turn, to trigger a number of additional tipping elements, physical, chemical, and biological, in motion, with potentially large impacts on the Arctic marine ecosystem.

Analysis of capacitive force acting on a cantilever tip at solid/liquid interfaces

NASA Astrophysics Data System (ADS)

Umeda, Ken-ichi; Kobayashi, Kei; Oyabu, Noriaki; Hirata, Yoshiki; Matsushige, Kazumi; Yamada, Hirofumi

2013-04-01

Dielectric properties of biomolecules or biomembranes are directly related to their structures and biological activities. Capacitance force microscopy based on the cantilever deflection detection is a useful scanning probe technique that can map local dielectric constant. Here we report measurements and analysis of the capacitive force acting on a cantilever tip at solid/liquid interfaces induced by application of an alternating voltage to explore the feasibility of the measurements of local dielectric constant by the voltage modulation technique in aqueous solutions. The results presented here suggest that the local dielectric constant measurements by the conventional voltage modulation technique are basically possible even in polar liquid media. However, the cantilever deflection is not only induced by the electrostatic force, but also by the surface stress, which does not include the local dielectric information. Moreover, since the voltage applied between the tip and sample are divided by the electric double layer and the bulk polar liquid, the capacitive force acting on the apex of the tip are strongly attenuated. For these reasons, the lateral resolution in the local dielectric constant measurements is expected to be deteriorated in polar liquid media depending on the magnitude of dielectric response. Finally, we present the criteria for local dielectric constant measurements with a high lateral resolution in polar liquid media.

The Aging Eye

MedlinePlus

... Search Search the NEI Website search NEI on Social Media | Search A-Z | en español | Text size S M ... Outreach Tools and Tips Watch, Listen, and Learn Social Media Glaucoma Glaucoma Learn About Glaucoma Keep Vision in ...

Tires: Traffic Safety Tips

DOT National Transportation Integrated Search

1996-01-01

This fact sheet, NHTSA Facts: Summer 1996, discuses motor vehicle tires. It includes how to buy the right tires (obtaining tires of the correct size, type and tread); how to grade the tires (treadwear, traction, and temperature resistance); and how t...

CSC Tip Sheets: Testimonial Videos

EPA Pesticide Factsheets

Testimonial videos can be used to communicate to your target audience from the perspective of someone like them who has participated in program activities and can speak to the benefits and motivations of the activities your program is promoting.

31 CFR 91.7 - Gambling.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., receipt, or other writing of a type ordinarily used in any illegal form of gambling such as a tip sheet or dream book, unless explained to the satisfaction of the head of the bureau or his delegate, shall be...

Aerosol filtration with steel fiber filters

NASA Astrophysics Data System (ADS)

Bergman, W.; Wilson, K.; Larsen, G.; Lopez, R.

1993-04-01

An experimental study has been conducted of aerosol penetration through a new high efficiency steel fiber filter and filter media that was developed in cooperation with Pall Corporation. Previous studies have shown that sintered steel fiber media have significant improvements in higher filter efficiency and lower pressure drop than the previous steel filter technology based on sintered powder metal media. In the present study, measurements were made of the penetration of dioctyl sebacate (DOS) aerosols through flat sheet samples, pleated cartridge filters, and a 1000 cfm filter having 64 cartridges housed in a 2 x 2 x 1 ft. frame. The steel fiber media used in our study consists of 2 micron diameter stainless steel (316 L) fibers sintered together into sheets.

FAQs about Facilities: Practical Tips for Planning Renovations and New School Library Media Centers.

ERIC Educational Resources Information Center

Lenk, Mary Anne

2002-01-01

Answers frequently asked questions (FAQs) related to planning for renovating or building school library media centers (SLMCs). Topics include the role of the school library media specialist, advance planning, importance of a written long-range plan, library consultants, courses on planning, design compromises, planning resources, professional…

Tips for Working with the Media

ERIC Educational Resources Information Center

Zeman, Gail M.

2011-01-01

Spending some time getting to know reporters, developing a sense of trust, and recognizing that one can meet each other's needs can go a long way toward making the school district-media relationship positive and symbiotic. Many districts have public information officers--even departments--that deal with the media every day. But it is good for…

Theory of buttressed marine ice sheet dynamics and its application to the assessment of tipping-point conditions

NASA Astrophysics Data System (ADS)

Pegler, S.

2017-12-01

Understanding the fate of the West Antarctic Ice Sheet is constrained by difficulties of resolving the buttressing effect of ice shelves and its dynamic response to grounding-line migration. This effect may be responsible for protecting a large majority of outlet glaciers in Antarctica against surging into the ocean. I present a theoretical methodology for assessing the positions and stability of grounding lines that incorporates closed-form, dynamic descriptions of ice-shelf buttressing and extensional (stretching) viscous stresses. The method is applied to assess the conditions for grounding-line tipping points. Such points are shown to produce abrupt `cliff-edge' transitions to runaway retreat, representing the so-called marine ice sheet instability. Depending on the bed profile, melt and calving rates, a tipping point can either lie very near to a local maximum in the bed topography or potentially far upstream of it, along a reverse bed. The model predictions for both wide and narrow embayments are validated by numerical simulations and laboratory experiments. A case study of Pine Island Glacier indicates the possibility for long-term stabilisation, with the analytical method affording an extensive exploration of scenarios. The theory also elucidates a mode of grounding-line migration controlled entirely by the determinants of the ice-shelf buttressing force, with a loss of sensitivity to basal conditions, contrasting with the conclusion from one-dimensional theory that the ice shelf is irrelevant. The results provide an interpretive framework for understanding grounding-line dynamics, its coupling with ice-shelf dynamics, an efficient exploration of parameter variation, and a complement to large-scale simulation.

Local measurement and numerical modeling of mass/heat transfer from a turbine blade in a linear cascade with tip clearance

NASA Astrophysics Data System (ADS)

Jin, Peitong

2000-11-01

Local mass/heat transfer measurements from the turbine blade near-tip and the tip surfaces are performed using the naphthalene sublimation technique. The experiments are conducted in a linear cascade consisting of five high-pressure blades with a central test-blade configuration. The incoming flow conditions are close to those of the gas turbine engine environment (boundary layer displacement thickness is about 0.01 of chord) with an exit Reynolds number of 6.2 x 105. The effects of tip clearance level (0.86%--6.90% of chord), mainstream Reynolds number and turbulence intensity (0.2 and 12.0%) are investigated. Two methods of flow visualization---oil and lampblack, laser light sheet smoke wire---as well as static pressure measurement on the blade surface are used to study the tip leakage flow and vortex in the cascade. In addition, numerical modeling of the flow and heat transfer processes in the linear cascade with different tip clearances is conducted using commercial software incorporating advanced turbulence models. The present study confirms many important results on the tip leakage flow and vortex from the literature, contributes to the current understanding in the effects of tip leakage flow and vortex on local heat transfer from the blade near-tip and the tip surfaces, and provides detailed local and average heat/mass transfer data applicable to turbine blade tip cooling design.

Antilock Braking Systems: Traffic Safety Tips

DOT National Transportation Integrated Search

1996-01-01

This fact sheet, the NHTSA Facts: Summer 1996, defines antilock braking systems, and discusses their benefits, how they work, and their major components. It also details how one would get used to antilock brakes, discussing how they feel and operate ...

CSC Tip Sheets: Conducting and Evaluating Pilot Projects

EPA Pesticide Factsheets

Learn how to conduct and evaluate pilot projects, which are opportunities to “test the waters” for your project on a small scale, provide insight and data on what works, and adjust your strategy for full-scale implementation.

News Releases, Press Releases, Tip Sheet Statements

Science.gov Websites

United States Census Bureau Topics Population Latest Information Age and Sex Ancestry Children Mobility Population Estimates Population Projections Race Veterans Economy Latest Information Portal Other Economic Programs Business Latest Information Business Characteristics Classification Codes

Bumpers: Traffic Safety Tips

DOT National Transportation Integrated Search

1996-01-01

This fact sheet, NHTSA Facts: Summer 1996, discusses automobile bumpers. It notes that a car bumper is not a safety device to prevent or reduce injuries to people in the car. Instead, it is designed to protect the hood, trunk, grille, parking lights,...

What You Need to Know When the Power Goes Out Unexpectedly

MedlinePlus

... Hot Weather Tips Warning Signs and Symptoms FAQs Social Media How to Stay Cool Missouri Cooling Centers Extreme ... PSAs for Disasters Resources for Emergency Health Professionals Social Media Health and Safety Concerns for All Disasters Animals ...

Impact of the Tips From Former Smokers Campaign on Population-Level Smoking Cessation, 2012–2015

PubMed Central

Davis, Kevin C.; Beistle, Diane; King, Brian A.; Duke, Jennifer; Rodes, Robert; Graffunder, Corinne

2018-01-01

This study provides estimates of the long-term cumulative impact of the Centers for Disease Control and Prevention’s national tobacco education campaign, Tips From Former Smokers (Tips), on population-level smoking cessation. We used recently published estimates of the association between increased Tips campaign media doses and quit attempts to calculate campaign-attributable population sustained (6-month) quits during 2012–2015. Tips led to approximately 522,000 sustained quits during 2012–2015. These findings indicate that the Tips campaign’s comprehensive approach to combining evidence-based messages with the promotion of cessation resources was successful in achieving substantial long-term cigarette cessation at the population level over multiple years. PMID:29862960

75 FR 41989 - Content of Periodicals Mail

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-20

... media, since they are not printed sheets. But specifically allowing de minimis product samples will... provision in the DMM allowing product samples in de minimis form to be included as part of a printed sheet...

A Measurement of Vocational Education’s Student Satisfaction in Learning Electronic Appliance Repair and Maintenance Course with CCTV Trainer Kit

NASA Astrophysics Data System (ADS)

Rakhmawati, Lusia; Irwansyah Febriyanto, Fariz

2018-04-01

This study aimed to investigate satisfaction levels, among of the eleventh-grade students majoring in audio-video technique, towards the instructional media CCTV trainer kit: The CCTV Prototype and job sheet on to and analyzed perspectives of the practical approach to learning using CCTV prototype to improve installation skills in the electronic appliance repair and maintenance class. Survey questionnaires and instructional media were applied to data collection. The students’ satisfaction towards the instructional media in teaching and learning process was presented in positive responses, 91.94 % satisfied. The finding reveals that the instructional media using trainer could better to overcome the need a practical approach to learning. Furthermore, using trainer kit media creates an environment where students can support each other and receive feedback from their peers. They performed practice activities that help them apply the new information from the steps on the job sheet.

Human platelet lysate supports the formation of robust human periodontal ligament cell sheets.

PubMed

Tian, Bei-Min; Wu, Rui-Xin; Bi, Chun-Sheng; He, Xiao-Tao; Yin, Yuan; Chen, Fa-Ming

2018-04-01

The use of stem cell-derived sheets has become increasingly common in a wide variety of biomedical applications. Although substantial evidence has demonstrated that human platelet lysate (PL) can be used for therapeutic cell expansion, either as a substitute for or as a supplement to xenogeneic fetal bovine serum (FBS), its impact on cell sheet production remains largely unexplored. In this study, we manufactured periodontal ligament stem cell (PDLSC) sheets in vitro by incubating PDLSCs in sheet-induction media supplemented with various ratios of PL and FBS, i.e. 10% PL without FBS, 7.5% PL + 2.5% FBS, 5% PL + 5% FBS, 2.5% PL + 7.5% FBS or 10% FBS without PL. Cultures with the addition of all the designed supplements led to successful cell sheet production. In addition, all the resultant cellular materials exhibited similar expression profiles of matrix-related genes and proteins, such as collagen I, fibronectin and integrin β1. Interestingly, the cell components within sheets generated by media containing both PL and FBS exhibited improved osteogenic potential. Following in vivo transplantation, all sheets supported significant new bone formation. Our data suggest that robust PDLSC sheets can be produced by applying PL as either an alternative or an adjuvant to FBS. Further examination of the relevant influences of human PL that benefit cell behaviour and matrix production will pave the way towards optimized and standardized conditions for cell sheet production. Copyright © 2017 John Wiley & Sons, Ltd.

Growing TiO2 nanowires on the surface of graphene sheets in supercritical CO2: characterization and photoefficiency.

PubMed

Farhangi, Nasrin; Medina-Gonzalez, Yaocihuatl; Chowdhury, Rajib Roy; Charpentier, Paul A

2012-07-27

Tremendous interest exists towards synthesizing nanoassemblies for dye-sensitized solar cells (DSSCs) using earth-abundant and -friendly materials with green synthetic approaches. In this work, high surface area TiO(2) nanowire arrays were grown on the surface of functionalized graphene sheets (FGSs) containing -COOH functionalities acting as a template by using a sol-gel method in the green solvent, supercritical carbon dioxide (scCO(2)). The effect of scCO(2) pressure (1500, 3000 and 5000 psi), temperature (40, 60 and 80 °C), acetic acid/titanium isopropoxide monomer ratios (HAc/TIP = 2, 4 and 6), functionalized graphene sheets (FGSs)/TIP weight ratios (1:20, 1:40 and 1:60 w/w) and solvents (EtOH, hexane) were investigated. Increasing the HAc/TIPweight ratio from 4 to 6 in scCO(2) resulted in increasing the TiO(2) nanowire diameter from 10 to 40 nm. Raman and high resolution XPS showed the interaction of TiO(2) with the -COOH groups on the surface of the graphene sheets, indicating that graphene acted as a template for polycondensation growth. UV-vis diffuse reflectance and photoluminescence spectroscopy showed a reduction in titania's bandgap and also a significant reduction in electron-hole recombination compared to bare TiO(2) nanowires. Photocurrent measurements showed that the TiO(2)nanowire/graphene composites prepared in scCO(2) gave a 5× enhancement in photoefficiency compared to bare TiO(2) nanowires.

Growing TiO2 nanowires on the surface of graphene sheets in supercritical CO2: characterization and photoefficiency

NASA Astrophysics Data System (ADS)

Farhangi, Nasrin; Medina-Gonzalez, Yaocihuatl; Chowdhury, Rajib Roy; Charpentier, Paul A.

2012-07-01

Tremendous interest exists towards synthesizing nanoassemblies for dye-sensitized solar cells (DSSCs) using earth-abundant and -friendly materials with green synthetic approaches. In this work, high surface area TiO2 nanowire arrays were grown on the surface of functionalized graphene sheets (FGSs) containing -COOH functionalities acting as a template by using a sol-gel method in the green solvent, supercritical carbon dioxide (scCO2). The effect of scCO2 pressure (1500, 3000 and 5000 psi), temperature (40, 60 and 80 °C), acetic acid/titanium isopropoxide monomer ratios (HAc/TIP = 2, 4 and 6), functionalized graphene sheets (FGSs)/TIP weight ratios (1:20, 1:40 and 1:60 w/w) and solvents (EtOH, hexane) were investigated. Increasing the HAc/TIPweight ratio from 4 to 6 in scCO2 resulted in increasing the TiO2 nanowire diameter from 10 to 40 nm. Raman and high resolution XPS showed the interaction of TiO2 with the -COOH groups on the surface of the graphene sheets, indicating that graphene acted as a template for polycondensation growth. UV-vis diffuse reflectance and photoluminescence spectroscopy showed a reduction in titania’s bandgap and also a significant reduction in electron-hole recombination compared to bare TiO2 nanowires. Photocurrent measurements showed that the TiO2nanowire/graphene composites prepared in scCO2 gave a 5× enhancement in photoefficiency compared to bare TiO2 nanowires.

Three-dimensional viscous fingering of miscible fluids in porous media

NASA Astrophysics Data System (ADS)

Suekane, Tetsuya; Ono, Jei; Hyodo, Akimitsu; Nagatsu, Yuichiro

2017-10-01

Viscous fingering is a flow instability that is induced at the displacement front when a less-viscous fluid (LVF) displaces a more-viscous fluid (MVF). Because of the opaque nature of porous media, most experimental investigations of the structure of viscous fingering and its development in time have been limited to two-dimensional porous media or Hele-Shaw cells. In this study, we investigate the three-dimensional characteristics of viscous fingering in porous media using a microfocused x-ray computer tomography (CT) scanner. Similar to two-dimensional experiments, characteristic events such as tip-splitting, shielding, and coalescence were observed in three-dimensional viscous fingering as well. With an increase in the Péclet number at a fixed viscosity ratio, M , the fingers appearing on the interface tend to be fine; however, the locations of the tips of the fingers remain the same for the same injected volume of the LVF. The finger extensions increase in proportion to ln M , and the number of fingers emerging at the initial interface increases with M . This fact agrees qualitatively with linear stability analyses. Within the fingers, the local concentration of NaI, which is needed for the x-ray CT scanner, linearly decreases, whereas it sharply decreases at the tips of the fingers. A locally high Péclet number as well as unsteady motions in lateral directions may enhance the dispersion at the tips of the fingers. As the viscosity ratio increases, the efficiency of each sweep monotonically decreases and reaches an asymptotic state; in addition, the degree of mixing increases with the viscosity ratio. For high flow rates, the asymptotic value of the sweep efficiency is low for high viscosity ratios, while there is no clear dependence of the asymptotic value on the Péclet number.

Recall and Believability of the Tips from Former Smokers Campaign among University Students

ERIC Educational Resources Information Center

Ickes, Melinda. J.; Butler, Karen; Rayens, Mary Kay; Noland, Melody; Wiggins, Amanda T.; Hahn, Ellen J.

2016-01-01

Background: Tobacco media campaigns are effective, but less is known regarding the impact on college students. Purpose: The purpose was to test the effects of an on-campus Tips television campaign on frequency and believability of ads recalled and to assess demographic and personal factors associated with believability. Methods: A…

Fermilab | Tevatron | Media

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram Google+ YouTube Flickr

Evaluating Potential Tipping Points of Antarctic basins

NASA Astrophysics Data System (ADS)

Durand, G.; Sainan, S.; Pattyn, F.; Jourdain, N.

2017-12-01

Antarctica is currently loosing mass and its forthcoming contribution to sea-level rise could substantially increase during the coming centuries. This is essentially due to geometrical constraints, i.e., in regions where grounded ice lies on a bedrock below sea-level sloping down towards the interior of the ice sheet (retrograde slope). For such a configuration the ice sheet is considered potentially unstable, as suggested by theory. However, recent observations on accelerated grounding-line retreat and new insights in modeling Pine Island and Thwaites glaciers give evidence that such self-sustained retreat, called marine ice sheet instability (MISI), has already been on its way. Although West Antarctica appears to be the most vulnerable region for MISI occurrence, similar topographic configurations are also observed in East Antarctica, in the Wilkes Basin in particular. Therefore, evaluating the MISI potential at a pan-Antarctic scale is becoming a priority. Here, using the f.ETISh ice sheet model, an ensemble of simulations of the entire contemporary Antarctic ice sheet has been carried out. In particular, we investigate the debuttressing of ice shelves required to initiate MISI for each coastal region around Antarctica by forcing the model with realistic sub-shelf melt pulses of varying duration and amplitude. We further identify the currently grounded areas where the outlet glaciers could hardly stabilize, the Amundsen Sea Sector being the more prone to large self-sustained retreats. On the contrary, the ability of Cook and Ninnis ice shelves to recover after large perturbations and enough buttress upstream outlet glaciers tends to limit self-sustained retreat of the sector. For each basin, rates of contribution to sea-level rise are discussed together with the RCPs and time when tipping points could be reached and MISI triggered.

Odometer Fraud: Traffic Safety Tips

DOT National Transportation Integrated Search

1996-01-01

This fact sheet, NHTSA Facts: Summer 1996, focuses on odometer fraud, which is a major problem for consumers. Some late model used cars have odometers that have been turned back. Any vehicle that has been driven a high number of miles but is only a f...

Tips for K-12 Educators for Helping Students Communicate and Create Using Visual Motion Media, Photography, and Technology

ERIC Educational Resources Information Center

TechTrends: Linking Research and Practice to Improve Learning, 2009

2009-01-01

This paper describes a particular lesson plan--the "Illustrating Project"--that has been successful for many classroom educators. The Illustrating Project calls for students, individually or in project groups, to illustrate some element of the curriculum via the media selected by the teacher. The selected media might be PowerPoint or some other…

Public Relations for School Library Media Programs: 500 Ways To Influence People and Win Friends for Your School Library Media Center.

ERIC Educational Resources Information Center

Flowers, Helen F.

This informative how-to guide explains public relations strategies and the audiences they target, with tips for customizing these tactics for particular libraries. Helpful techniques are recommended for promoting the use of library media services by students, faculty, building administrators, and school support staff. Readers will also learn how…

Does Digital Video Advertising Increase Population-Level Reach of Multimedia Campaigns? Evidence From the 2013 Tips From Former Smokers Campaign

PubMed Central

Shafer, Paul R; Rodes, Robert; Kim, Annice; Hansen, Heather; Patel, Deesha; Coln, Caryn; Beistle, Diane

2016-01-01

Background Federal and state public health agencies in the United States are increasingly using digital advertising and social media to promote messages from broader multimedia campaigns. However, little evidence exists on population-level campaign awareness and relative cost efficiencies of digital advertising in the context of a comprehensive public health education campaign. Objective Our objective was to compare the impact of increased doses of digital video and television advertising from the 2013 Tips From Former Smokers (Tips) campaign on overall campaign awareness at the population level. We also compared the relative cost efficiencies across these media platforms. Methods We used data from a large national online survey of approximately 15,000 US smokers conducted in 2013 immediately after the conclusion of the 2013 Tips campaign. These data were used to compare the effects of variation in media dose of digital video and television advertising on population-level awareness of the Tips campaign. We implemented higher doses of digital video among selected media markets and randomly selected other markets to receive similar higher doses of television ads. Multivariate logistic regressions estimated the odds of overall campaign awareness via digital or television format as a function of higher-dose media in each market area. All statistical tests used the .05 threshold for statistical significance and the .10 level for marginal nonsignificance. We used adjusted advertising costs for the additional doses of digital and television advertising to compare the cost efficiencies of digital and television advertising on the basis of costs per percentage point of population awareness generated. Results Higher-dose digital video advertising was associated with 94% increased odds of awareness of any ad online relative to standard-dose markets (P<.001). Higher-dose digital advertising was associated with a marginally nonsignificant increase (46%) in overall campaign awareness regardless of media format (P=.09). Higher-dose television advertising was associated with 81% increased odds of overall ad awareness regardless of media format (P<.001). Increased doses of television advertising were also associated with significantly higher odds of awareness of any ad on television (P<.001) and online (P=.04). The adjusted cost of each additional percentage point of population-level reach generated by higher doses of advertising was approximately US $440,000 for digital advertising and US $1 million for television advertising. Conclusions Television advertising generated relatively higher levels of overall campaign awareness. However, digital video was relatively more cost efficient for generating awareness. These results suggest that digital video may be used as a cost-efficient complement to traditional advertising modes (eg, television), but digital video should not replace television given the relatively smaller audience size of digital video viewers. PMID:27627853

Does Digital Video Advertising Increase Population-Level Reach of Multimedia Campaigns? Evidence From the 2013 Tips From Former Smokers Campaign.

PubMed

Davis, Kevin C; Shafer, Paul R; Rodes, Robert; Kim, Annice; Hansen, Heather; Patel, Deesha; Coln, Caryn; Beistle, Diane

2016-09-14

Federal and state public health agencies in the United States are increasingly using digital advertising and social media to promote messages from broader multimedia campaigns. However, little evidence exists on population-level campaign awareness and relative cost efficiencies of digital advertising in the context of a comprehensive public health education campaign. Our objective was to compare the impact of increased doses of digital video and television advertising from the 2013 Tips From Former Smokers (Tips) campaign on overall campaign awareness at the population level. We also compared the relative cost efficiencies across these media platforms. We used data from a large national online survey of approximately 15,000 US smokers conducted in 2013 immediately after the conclusion of the 2013 Tips campaign. These data were used to compare the effects of variation in media dose of digital video and television advertising on population-level awareness of the Tips campaign. We implemented higher doses of digital video among selected media markets and randomly selected other markets to receive similar higher doses of television ads. Multivariate logistic regressions estimated the odds of overall campaign awareness via digital or television format as a function of higher-dose media in each market area. All statistical tests used the .05 threshold for statistical significance and the .10 level for marginal nonsignificance. We used adjusted advertising costs for the additional doses of digital and television advertising to compare the cost efficiencies of digital and television advertising on the basis of costs per percentage point of population awareness generated. Higher-dose digital video advertising was associated with 94% increased odds of awareness of any ad online relative to standard-dose markets (P<.001). Higher-dose digital advertising was associated with a marginally nonsignificant increase (46%) in overall campaign awareness regardless of media format (P=.09). Higher-dose television advertising was associated with 81% increased odds of overall ad awareness regardless of media format (P<.001). Increased doses of television advertising were also associated with significantly higher odds of awareness of any ad on television (P<.001) and online (P=.04). The adjusted cost of each additional percentage point of population-level reach generated by higher doses of advertising was approximately US $440,000 for digital advertising and US $1 million for television advertising. Television advertising generated relatively higher levels of overall campaign awareness. However, digital video was relatively more cost efficient for generating awareness. These results suggest that digital video may be used as a cost-efficient complement to traditional advertising modes (eg, television), but digital video should not replace television given the relatively smaller audience size of digital video viewers.

Roller Coaster Science.

ERIC Educational Resources Information Center

Sumners, Carolyn; Jones, Howard L.

1983-01-01

Discusses the science of roller coasters, relating gravity, potential/kinetic energy, inertia, and centripetal force to the various parts of the ride, providing tips on linking classroom discussions to field trips. Includes sample student activity sheet and source for additional units using amusement park rides/playground activities to teach…

Taking Care of Your Diabetes Means Taking Care of Your Heart (Tip Sheet)

MedlinePlus

... Diabetes Means Taking Care of Your Heart Taking Care of Your Diabetes Means Taking Care of Your Heart Diabetes and Heart Disease For ... What you can do now Ask your health care team these questions: What can I do to ...

Light Sheet Fluorescence Microscopy Quantifies Calcium Oscillations in Root Hairs of Arabidopsis thaliana.

PubMed

Candeo, Alessia; Doccula, Fabrizio G; Valentini, Gianluca; Bassi, Andrea; Costa, Alex

2017-07-01

Calcium oscillations play a role in the regulation of the development of tip-growing plant cells. Using optical microscopy, calcium oscillations have been observed in a few systems (e.g. pollen tubes, fungal hyphae and algal rhizoids). High-resolution, non-phototoxic and rapid imaging methods are required to study the calcium oscillation in root hairs. We show that light sheet fluorescence microscopy is optimal to image growing root hairs of Arabidopsis thaliana and to follow their oscillatory tip-focused calcium gradient. We describe a protocol for performing live imaging of root hairs in seedlings expressing the cytosol-localized ratiometric calcium indicator Yellow Cameleon 3.6. Using this protocol, we measured the calcium gradient in a large number of root hairs. We characterized their calcium oscillations and correlated them with the rate of hair growth. The method was then used to screen the effect of auxin on the properties of the growing root hairs. © The Author 2017. Published by Oxford University Press on behalf of Japanese Society of Plant Physiologists.

Nanobits, Nembranes and Micro Four-Point Probes: Customizable Tools for insitu Manipulation and Characterisation of Nanostructures

NASA Astrophysics Data System (ADS)

Boggild, Peter; Hjorth Petersen, Dirch; Sardan Sukas, Ozlem; Dam, Henrik Friis; Lei, Anders; Booth, Timothy; Molhave, Kristian; Eicchorn, Volkmar

2010-03-01

We present a range of highly adaptable microtools for direct interaction with nanoscale structures; (i) semiautomatic pick-and-place assembly of multiwalled carbon nanotubes onto cantilevers for high-aspect ratio scanning probe microscopy, using electrothermal microgrippers inside a SEM. Topology optimisation was used to calculate the optimal gripper shape defined by the boundary conditions, resulting in 10-100 times better performance. By instead pre-defining detachable tips using electron beam lithography, free-form scanning probe tips (Nanobits) can be mounted in virtually any position on a cantilever; (ii) scanning micro four point probes allow fast, non- destructive mapping of local electrical properties (sheet resistance and Hall mobility) and hysteresis effects of graphene sheets; (iii) sub 100 nm freestanding devices with wires, heaters, actuators, sensors, resonators and probes were defined in a 100 nm thin membrane with focused ion beam milling. By patterning generic membrane templates (Nembranes) the fabrication time of a TEM compatible NEMS device is effectively reduced to less around 20 minutes.

Investigation of tip sonication effects on structural quality of graphene nanoplatelets (GNPs) for superior solvent dispersion.

PubMed

Baig, Zeeshan; Mamat, Othman; Mustapha, Mazli; Mumtaz, Asad; Munir, Khurram S; Sarfraz, Mansoor

2018-07-01

The exceptional properties of graphene and its structural uniqueness can improve the performance of nanocomposites if it can attain the uniform dispersion. Tip sonication assisted graphene solvent dispersion has been emerged as an efficient approach but it can cause significant degradation of graphene structure. This study aimed to evaluate the parametric influence of tip sonication on the characteristics of sp 2 carbon structure in graphene nanoplatelets by varying the sonication time and respective energy at three different amplitudes (60%, 80% and 100%). The study is essential to identify appropriate parameters so as to achieve high-quality and defect-free graphene with a highly desirable aspect ratio after solvent dispersion for composite reinforcement. Quantitative approach via Raman spectroscopy is used to find the defect ratio and lateral size of graphene evolved under the effect of tip sonication parameters. Results imply that the defect ratio is steady and increases continually with GNPs, along with the transformation to the nano-crystalline stage I up to 60 min sonication at all amplitudes. Exfoliation was clearly observed at all amplitudes together with sheet re-stacking due to considerable size reduction of sheets with large quantity. Finally, considerable GNPs fragmentation occurred during sonication with increased amplitude and time as confirmed by the reduction of sp 2 domain (La) and flake size. This also validates the formation of edge-type defect in graphene. Convincingly, lower amplitude and time (up to 60 min) produce better results for a low defect content and larger particle size as quantified by Raman analysis. Copyright © 2018 Elsevier B.V. All rights reserved.

NOAA - National Oceanic and Atmospheric Administration - Media Resources

Science.gov Websites

the footage you're looking for in the shot sheets provided below or complete B-Roll list, please send an e-mail to the NOAA Video Studio at broll@noaa.gov. NOAA B-Roll Shot Sheets (Text & PDF

Climate Science in Social Media: What's Worked, and What Hasn't

NASA Astrophysics Data System (ADS)

Sinclair, P.

2015-12-01

A common conception of social media is that the definition of success is a huge number of viewers and followers. While these outcomes not undesirable, they are not the only signs of success. More important than the size of the audience, is how well that audience follows and in turn, propagates the desired message. Dark Snow project has been successful in driving a global conversation about the Greenland ice sheet, not by creating huge numbers of viewers and followers, but due to a significant, and highly motivated, following among media gatekeepers, academic messengers, and social media activists. It's very important that, from the start, the Dark Snow story - that changes in ice sheet albedo may be driving increased melt, was effectively encoded, or "branded", in the project's name - "Dark Snow" - a vivid and easily illustrated visual image. A simple concept that is easy to describe and understand, but profound in implication, has allowed for wide discussion among professionals in science and media, as well as the general public.

Generating A Strobed Laser Light Sheet

NASA Technical Reports Server (NTRS)

Leighty, Bradley D.; Franke, John M.; Rhodes, David B.; Jones, Stephen B.

1994-01-01

An optoelectronic system generating synchronous, strobed sheet of laser light developed for use in making visible flow of air about model helicopter rotor. Used in wind-tunnel tests to determine actual locations of vortices for comparison with locations predicted by mathematical models to validate models. Each blade tip produces vortex. By establishing successive vortex locations, researcher determines trajectory of vortex pattern. Light-sheet strobe circuits provide selection of blade positions, strobe-pulse durations, and multiple pulses per revolution for rotors having two to nine blades. To make flow visible, vaporizing propylene glycol injected upstream of model. System also provides calibrated trigger delay of strobe pulses, adjustable strobe-pulse durations, selectable number of blades, and slip-sync mode to make flow visible as though in slow motion.

Effects of miles per gallon feedback on fuel efficiency in gas-powered cars.

DOT National Transportation Integrated Search

2009-10-01

This study tested the impact of continuous miles per gallon (MPG) feedback on driving : behavior and fuel efficiency in gas-powered cars. We compared an experimental condition, : where drivers received real-time MPG feedback and a tip sheet, to a con...

Tactics for Improving Parenting Skills (TIPS).

ERIC Educational Resources Information Center

Algozzine, Bob, Ed.; Ysseldyke, Jim, Ed.

This manual presents 99 one-sheet informational brochures designed to improve parenting skills. Each brochure is in a format suitable for duplicating, folding, and distributing. Each parenting "tactic" offers references to related brochures. Tactics are grouped under the following broad areas: (1) home/family involvement (e.g., accepting "The…

Tips for Effective Management

ERIC Educational Resources Information Center

Supple, Kevin F.

2009-01-01

School business officials' days are filled with numbers and reports--audits, balance sheets, check registers, financial statements, journal entries, vouchers, and warrant reports, just to name a few. Those are all important tools that school business officers use to manage the financial resources of the district effectively. However, they are also…

Retention of Nontraditional Students. Tip Sheet.

ERIC Educational Resources Information Center

Ohio State Univ., Columbus. Instructional Materials Lab.

This publication begins with a list of suggestions for increasing the retention of male and female students pursuing nontraditional occupations. It then highlights five successful Ohio programs for the retention of these students: (1) Overcoming Sex Bias and Sex Stereotyping in Secondary Vocational Education--Nontraditional Support (Great Oaks…

Transporting Your Children Safely: Traffic Safety Tips

DOT National Transportation Integrated Search

1996-01-01

This fact sheet from NHTSA Facts: Summer 1996 discusses the use of child safety seats in cars. It describes the proper use of the seats, how to select one that fits both your child and the car, and lists problems to avoid. It mentions where to place ...

TIPS Pamphlets for Parents.

ERIC Educational Resources Information Center

Algozzine, Bob, Ed.; Ysseldyke, Jim, Ed.

This manual presents 99 one-sheet informational brochures designed to improve parenting skills for children with and without disabilities. Each brochure is in a format suitable for duplicating, folding, and distributing. Each brochure offers references to related brochures in the collection. Brochures are grouped under the following broad areas:…

How Does Information Spread on Social Media Lead to Effective Change?

PubMed

Varghese, Thomas K

2017-09-01

Social media encompasses computer-mediated technologies that facilitate the creation and sharing of information, ideas, and other forms of expression via virtual communities and networks. The key, of course, is the ability and willingness for information to be shared. But why does some information spread on social media and not others? What factors translate social media awareness to action? In this article, we explore these themes using case studies, as well as tips on how you can utilize social media to effectively champion a cause.

77 FR 13529 - Agency Information Collection Activities; Proposed Collection; Comment Request-SuperTracker...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-07

... tip messages to Facebook or Twitter using their personal social media account. Through leveraging the user's existing social network, the user is more likely to experience positive feedback and encouragement in achieving their dietary and/or physical activity goals. Social media functionality is provided...

The School Leader's Guide to Social Media

ERIC Educational Resources Information Center

Williamson, Ronald; Johnston, J. Howard

2012-01-01

Social media has exploded onto American culture--including our schools--giving educators a unique opportunity to shape this phenomenon into a powerful tool for improving educational leadership practices. With real-world examples and practical tips, this essential guide shows school leaders how to address both the potential benefits and common…

100 Library Lifesavers: A Survival Guide for School Library Media Specialists.

ERIC Educational Resources Information Center

Bacon, Pamela S.

This book contains tips (author's suggestions), tools (ready-to-use lifesavers), and talk (quotes from practicing media specialists) for school librarians at all grade levels. A total of 100 lifesavers are included, covering areas such as inventory, motivation strategies, disciplinary approaches, library checkout, Internet searching, the traveling…

Basic Media in Education.

ERIC Educational Resources Information Center

Harrell, John

Intended as a guide to the use of different media for use in the classroom, this document demonstrates alternative approaches that may be taken to depicting and communicating images and concepts to others. Some basic tools and materials--including a ruler, matte knife, rubber cement, stapler, felt-tip pens, paint brushes, and lettering pens--are…

Conformation and Dynamics of a Flexible Sheet in Solvent Media by Monte Carlo Simulations

NASA Astrophysics Data System (ADS)

Pandey, Ras; Anderson, Kelly; Heinz, Hendrik; Farmer, Barry

2005-03-01

Flexibility of the clay sheet is limited even in the ex-foliated state in some solvent media. A coarse grained model is used to investigate dynamics and conformation of a flexible sheet to model such a clay platelet in an effective solvent medium on a cubic lattice of size L^3 with lattice constant a. The undeformed sheet is described by a square lattice of size Ls^2, where, each node of the sheet is represented by the unit cube of the cubic lattice and 2a is the minimum distance between the nearest neighbor nodes to incorporate the excluded volume constraints. Additionally, each node interacts with neighboring nodes and solvent (empty) sites within a range ri. Each node execute their stochastic motion with the Metropolis algorithm subject to bond length fluctuation and excluded volume constraints. Mean square displacements of the center node and that of its center of mass are investigated as a function of time step for a set of these parameters. The radius of gyration (Rg) is also examined concurrently to understand its relaxation. Multi-scale segmental dynamics of the sheet is studied by identifying the power-law dependence in various time regimes. Relaxation of Rg and its dependence of temperature are planned to be discussed.

The challenge of stereo PIV measurements in the tip gap of a transonic compressor rotor with casing treatment

NASA Astrophysics Data System (ADS)

Voges, Melanie; Willert, Christian E.; Mönig, Reinhard; Müller, Martin W.; Schiffer, Heinz-Peter

2012-03-01

This contribution is aimed at summarizing the effort taken to apply stereoscopic PIV (SPIV) measurements in the tip clearance of a transonic compressor rotor equipped with a casing treatment. A light sheet probe was placed downstream of the stator and aligned to pass the light sheet through a stator passage into the blade tip clearance of the rotor. A setup with three cameras has been used in order to record the entire 2C velocity field and the smaller area of 3C field of view at the same time instance for comparison with earlier 2C PIV results. A homogeneous seeding distribution was achieved by means of a smoke generator. The main emphasis of the SPIV measurement was to establish a data set with high spatial resolution close to the compressor casing, where the aerodynamic effects of a CT are known to be strong. The paper will discuss some major aspects of the utilized PIV data processing and point out a variety of frequently underestimated error sources that influence the overall quality of the recovered data in spite of the fact that the individual PIV recordings seemed to be of very good quality. Thus, the authors will not focus on the PIV results and related interpretation of the flow field, but on the optimization and procedures applied during setup of the experiment and data processing, respectively.

Recovery of fission product palladium from acidic high level waste solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rizvi, G.H.; Mathur, J.N.; Murali, M.S.

1996-07-01

The recovery of palladium from a synthetic pressurized heavy water reactor high level waste (PHWR-HLW) solution has been carried out, and the best reagents to use for the actual HLW solutions are discussed. The extraction of palladium from nitric acid solutions has been carried out using Cyanex-471X (triisobutylphosphine sulfide, TIPS) as the extractant. The metal ion could be quantitatively extracted from solutions with nitric acid concentrations between 2.0 and 6.0 M. The species extracted into the organic phase was found to be Pd(NO{sub 3}){sub 2}{center_dot}TIPS. Nitric acid in the range of 2.0 to 5.0 M had no effect on TIPSmore » for at least 71 hours. A systematic study of gamma irradiation on loading and stripping of palladium from loaded organic phases using several potential extractants, TIPS, alpha benzoin oxime, dioctylsulfide, and dioctylsulfoxide has been made. A flow sheet for the recovery of palladium from actual HLW solutions using TIPS is proposed.« less

PFAS methods and guidance for sampling and analyzing water and other environmental media (Technical Brief)

EPA Pesticide Factsheets

EPA's methods for analyzing PFAS in environmental media are in various stages of development. This fact sheet summarizes EPA's analytical methods development for groundwater, surface water, wastewater, and solids, including soils, sediments, and biosolids

Educational Technology and Distance Education. An ERIC Fact Sheet.

ERIC Educational Resources Information Center

Ely, Donald P.

The role of educational media and technology personnel in the development of distance education curriculum is the focus of this fact sheet. The definition and background of distance education are briefly described as nontraditional education involving communication between teachers and learners by such means as correspondence, radio, and…

Fact Sheets on Institutional Racism.

ERIC Educational Resources Information Center

Foundation for Change, Inc., New York, NY.

This fact sheet on institutional racism contains statistics on white control of the economy, health, housing, education, the media, and government. It also shows the oppression of minorities in these areas. The areas of wealth, the stock exchange, business, banks, unions, poverty, and unemployment, are discussed in terms of economy. Health matters…

First Year Firsts

ERIC Educational Resources Information Center

Dickinson, Gail K.

2007-01-01

In this article, the author shares some tips for the new or not-so-new library media specialists. During the first week of school, the library media specialist's life will be filled with teacher work days, mandatory meetings, piles of stuff with no apparent purpose, and a line of teachers and other staff who want something from the library. There…

Press, Radio, and TV Tips for Education Associations. PR Bookshelf No. 9.

ERIC Educational Resources Information Center

National Education Association, Washington, DC.

This booklet contains suggestions and techniques aimed at those individuals in education associations who are in charge of news media relations for their organizations. The following aspects of reporting news to the media are discussed: getting organized and acquainted, thinking like a newsperson, writing clearly and simply, typing the news…

Downwash in Vortex Region Behind Rectangular Half-wing at Mach Number 1.91

NASA Technical Reports Server (NTRS)

Cummings, John L; Haefeli, Rudolph C

1950-01-01

Results of an experimental investigation to determine downwash and wake characteristics in region of trailing vortex system behind a rectangular half-wing at Mach number 1.91 are presented. The wing had a 5-percent thick symmetric diamond cross section beveled to a knife edge at the tip. At small angles of attack, downwash angles were in close agreement with predictions of linearized theory based on the assumption of an undistorted vortex sheet. At higher angles of attack, the flow was greatly influenced by the rolling up of the vortex sheet.

Unzip instabilities: Straight to oscillatory transitions in the cutting of thin polymer sheets

NASA Astrophysics Data System (ADS)

Reis, P. M.; Kumar, A.; Shattuck, M. D.; Roman, B.

2008-06-01

We report an experimental investigation of the cutting of a thin brittle polymer sheet with a blunt tool. It was recently shown that the fracture path becomes oscillatory when the tool is much wider than the sheet thickness. Here we uncover two novel transitions from straight to oscillatory fracture by varying either the tilt angle of the tool or the speed of cutting, respectively. We denote these by angle and speed unzip instabilities and analyze them by quantifying both the dynamics of the crack tip and the final shapes of the fracture paths. Moreover, for the speed unzip instability, the straight crack lip obtained at low speeds exhibits out-of-plane buckling undulations (as opposed to being flat above the instability threshold) suggesting a transition from ductile to brittle fracture.

Digital case-based learning system in school.

PubMed

Gu, Peipei; Guo, Jiayang

2017-01-01

With the continuing growth of multi-media learning resources, it is important to offer methods helping learners to explore and acquire relevant learning information effectively. As services that organize multi-media learning materials together to support programming learning, the digital case-based learning system is needed. In order to create a case-oriented e-learning system, this paper concentrates on the digital case study of multi-media resources and learning processes with an integrated framework. An integration of multi-media resources, testing and learning strategies recommendation as the learning unit is proposed in the digital case-based learning framework. The learning mechanism of learning guidance, multi-media materials learning and testing feedback is supported in our project. An improved personalized genetic algorithm which incorporates preference information and usage degree into the crossover and mutation process is proposed to assemble the personalized test sheet for each learner. A learning strategies recommendation solution is proposed to recommend learning strategies for learners to help them to learn. The experiments are conducted to prove that the proposed approaches are capable of constructing personalized sheets and the effectiveness of the framework.

Digital case-based learning system in school

PubMed Central

Gu, Peipei

2017-01-01

With the continuing growth of multi-media learning resources, it is important to offer methods helping learners to explore and acquire relevant learning information effectively. As services that organize multi-media learning materials together to support programming learning, the digital case-based learning system is needed. In order to create a case-oriented e-learning system, this paper concentrates on the digital case study of multi-media resources and learning processes with an integrated framework. An integration of multi-media resources, testing and learning strategies recommendation as the learning unit is proposed in the digital case-based learning framework. The learning mechanism of learning guidance, multi-media materials learning and testing feedback is supported in our project. An improved personalized genetic algorithm which incorporates preference information and usage degree into the crossover and mutation process is proposed to assemble the personalized test sheet for each learner. A learning strategies recommendation solution is proposed to recommend learning strategies for learners to help them to learn. The experiments are conducted to prove that the proposed approaches are capable of constructing personalized sheets and the effectiveness of the framework. PMID:29107965

Theoretical aspects of fracture mechanics

NASA Astrophysics Data System (ADS)

Atkinson, C.; Craster, R. V.

1995-03-01

In this review we try to cover various topics in fracture mechanics in which mathematical analysis can be used both to aid numerical methods and cast light on key features of the stress field. The dominant singular near crack tip stress field can often be parametrized in terms of three parameters K(sub I), K(sub II) and K(sub III) designating three fracture modes each having an angular variation entirely specified for the stress tensor and displacement vector. These results and contact zone models for removing the interpenetration anomaly are described. Generalizations of the above results to viscoelastic media are described. For homogeneous media with constant Poisson's ratio the angular variation of singular crack tip stresses and displacements are shown to be the same for all time and the same inverse square root singularity as occurs in the elastic medium case is found (this being true for a time varying Poisson ratio too). Only the stress intensity factor varies through time dependence of loads and relaxation properties of the medium. For cracks against bimaterial interfaces both the stress singularity and angular form evolve with time as a function of the time dependent properties of the bimaterial. Similar behavior is identified for sharp notches in viscoelastic plates. The near crack tip behavior in material with non-linear stress strain laws is also identified and stress singularities classified in terms of the hardening exponent for power law hardening materials. Again for interface cracks the near crack tip behavior requires careful analysis and it is shown that more than one singular term may be present in the near crack tip stress field. A variety of theory and applications is presented for inhomogeneous elastic media, coupled thermoelasticity etc. Methods based on reciprocal theorems and dual functions which can also aid in getting awkward singular stress behavior from numerical solutions are also reviewed. Finally theoretical calculations of fiber reinforced and particulate composite toughening mechanisms are briefly reviewed.

Resistance Spot Welding of AA5052 Sheet Metal of Dissimilar Thickness

NASA Astrophysics Data System (ADS)

Mat Din, N. A.; Zuhailawati, H.; Anasyida, A. S.

2016-02-01

Resistance spot welding of dissimilar thickness of AA5052 aluminum alloy was performed in order to investigate the effect of metal thickness on the weldment strength. Resistance spot welding was done using a spot welder machine available in Coraza Systems Sdn Bhd using a hemispherical of chromium copper electrode tip with radius of 6.00 mm under 14 kA of current and 0.02 bar of pressure for all thickness combinations. Lap joint configuration was produced between 2.0 mm thick sheet and 1.2 - 3.2 mm thick sheet, respectively. Microstructure of joint showed asymmetrical nugget shape that was larger on the thicker side indicating larger molten metal volume. Joint 2.0 mm x 3.2 mm sheets has the lowest hardness in both transverse direction and through thickness direction because less heat left in the weld nugget. The microstructure shows that this joint has coarse grains of HAZ. As thickness of sheet metal increased, the failure load of the joints increased. However, there was no linear correlation established between joint strength and metal thickness due to different shape of fusion zone in dissimilar thickness sheet metal.

Life, Living, and Learning in the Teen Years.

ERIC Educational Resources Information Center

Wisconsin State Dept. of Public Instruction, Madison.

This packet contains articles by and for teenagers and articles and tips sheets for educators and parents. Included are: (1) "What Teens Need from Teachers, Parents, and Other Adults" (Stephen Small); (2) "Visually Impaired, Deaf Teens Share Views"; (3) "Teens Benefit from Community Service" (Kelli Krueger); (4) "My Experience in Foster Care;" (5)…

Tip Sheet for SEAs: Engaging Parents and Family Members in Postschool Outcome Stakeholder Groups

ERIC Educational Resources Information Center

National Post-School Outcomes Center, 2013

2013-01-01

Involving parents and other family representatives in the Indicator B-14 Post-School Outcomes (PSO) Survey activities can help State Education Agencies (SEAs) develop strategies to increase annual response rates, communicate results to stakeholders, and build support for program improvement and systems change. Perspectives expressed by families of…

The Influence of Welding Parameters on the Nugget Formation of Resistance Spot Welding of Inconel 625 Sheets

NASA Astrophysics Data System (ADS)

Rezaei Ashtiani, Hamid Reza; Zarandooz, Roozbeh

2015-09-01

A 2D axisymmetric electro-thermo-mechanical finite element (FE) model is developed to investigate the effect of current intensity, welding time, and electrode tip diameter on temperature distributions and nugget size in resistance spot welding (RSW) process of Inconel 625 superalloy sheets using ABAQUS commercial software package. The coupled electro-thermal analysis and uncoupled thermal-mechanical analysis are used for modeling process. In order to improve accuracy of simulation, material properties including physical, thermal, and mechanical properties have been considered to be temperature dependent. The thickness and diameter of computed weld nuggets are compared with experimental results and good agreement is observed. So, FE model developed in this paper provides prediction of quality and shape of the weld nuggets and temperature distributions with variation of each process parameter, suitably. Utilizing this FE model assists in adjusting RSW parameters, so that expensive experimental process can be avoided. The results show that increasing welding time and current intensity lead to an increase in the nugget size and electrode indentation, whereas increasing electrode tip diameter decreases nugget size and electrode indentation.

A Hybrid Vortex Sheet / Point Vortex Model for Unsteady Separated Flows

NASA Astrophysics Data System (ADS)

Darakananda, Darwin; Eldredge, Jeff D.; Colonius, Tim; Williams, David R.

2015-11-01

The control of separated flow over an airfoil is essential for obtaining lift enhancement, drag reduction, and the overall ability to perform high agility maneuvers. In order to develop reliable flight control systems capable of realizing agile maneuvers, we need a low-order aerodynamics model that can accurately predict the force response of an airfoil to arbitrary disturbances and/or actuation. In the present work, we integrate vortex sheets and variable strength point vortices into a method that is able to capture the formation of coherent vortex structures while remaining computationally tractable for control purposes. The role of the vortex sheet is limited to tracking the dynamics of the shear layer immediately behind the airfoil. When parts of the sheet develop into large scale structures, those sections are replaced by variable strength point vortices. We prevent the vortex sheets from growing indefinitely by truncating the tips of the sheets and transfering their circulation into nearby point vortices whenever the length of sheet exceeds a threshold. We demonstrate the model on a variety of canonical problems, including pitch-up and impulse translation of an airfoil at various angles of attack. Support by the U.S. Air Force Office of Scientific Research (FA9550-14-1-0328) with program manager Dr. Douglas Smith is gratefully acknowledged.

Anisotropic microporous supports impregnated with polymeric ion-exchange materials

DOEpatents

Friesen, Dwayne; Babcock, Walter C.; Tuttle, Mark

1985-05-07

Novel ion-exchange media are disclosed, the media comprising polymeric anisotropic microporous supports containing polymeric ion-exchange or ion-complexing materials. The supports are anisotropic, having small exterior pores and larger interior pores, and are preferably in the form of beads, fibers and sheets.

Fermilab | Science

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Tevatron experiments Tevatron operation Shutdown process For the media Video of shutdown event Guest book Quick Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter

Simple Tips for Helping Students Become Safer, Smarter Social Media Users

ERIC Educational Resources Information Center

Agosto, Denise E.; Abbas, June

2016-01-01

In thinking about teens and online risks, school librarians need to know researchers generally agree that, despite the popular image of pedophiles and criminals lurking online waiting to harm innocent young people, in reality social media use is only about as risky as most everyday social interactions in the offline world (Agosto and Abbas 2013).…

Extending the Five-Foot Bookshelf: More Essential Books for Professionals Who Serve Teens.

ERIC Educational Resources Information Center

Rosenzweig, Susan

2000-01-01

Provides annotated bibliographies for five books that are recommended professional reading for librarians serving teens. Topics include American Indian stereotypes in the media; a leadership guide for school library media specialists; views of teens; how teens who are different are often outcasts; and tips for public library young adult services.…

A physical mechanism producing suprathermal populations and initiating substorms in the Earth's magnetotail

NASA Astrophysics Data System (ADS)

Sarafopoulos, D. V.

2008-06-01

We suggest a candidate physical mechanism, combining there dimensional structure and temporal development, which is potentially able to produce suprathermal populations and cross-tail current disruptions in the Earth's plasma sheet. At the core of the proposed process is the "akis" structure; in a thin current sheet (TCS) the stretched (tail-like) magnetic field lines locally terminate into a sharp tip around the tail midplane. At this sharp tip of the TCS, ions become non-adiabatic, while a percentage of electrons are accumulated and trapped: The strong and transient electrostatic electric fields established along the magnetic field lines produce suprathermal populations. In parallel, the tip structure is associated with field aligned and mutually attracted parallel filamentary currents which progressively become more intense and inevitably the structure collapses, and so does the local TCS. The mechanism is observationally based on elementary, almost autonomous and spatiotemporal entities that correspond each to a local thinning/dipolarization pair having duration of ~1 min. Energetic proton and electron populations do not occur simultaneously, and we infer that they are separately accelerated at local thinnings and dipolarizations, respectively. In one example energetic particles are accelerated without any dB/dt variation and before the substorm expansion phase onset. A particular effort is undertaken demonstrating that the proposed acceleration mechanism may explain the plasma sheet ratio Ti/Te≍7. All our inferences are checked by the highest resolution datasets obtained by the Geotail Energetic Particles and Ion Composition (EPIC) instrument. The energetic particles are used as the best diagnostics for the accelerating source. Near Earth (X≍10 RE) selected events support our basic concept. The proposed mechanism seems to reveal a fundamental building block of the substorm phenomenon and may be the basic process/structure, which is now missing, that might help explain the persistent, outstanding deficiencies in our physical description of magnetospheric substorms. The mechanism is tested, checked, and found consistent with substorm associated observations performed ~30 and 60 RE away from Earth.

Towards a tipping point in responding to change: rising costs, fewer options for Arctic and global societies.

PubMed

Huntington, Henry P; Goodstein, Eban; Euskirchen, Eugénie

2012-02-01

Climate change incurs costs, but government adaptation budgets are limited. Beyond a certain point, individuals must bear the costs or adapt to new circumstances, creating political-economic tipping points that we explore in three examples. First, many Alaska Native villages are threatened by erosion, but relocation is expensive. To date, critically threatened villages have not yet been relocated, suggesting that we may already have reached a political-economic tipping point. Second, forest fires shape landscape and ecological characteristics in interior Alaska. Climate-driven changes in fire regime require increased fire-fighting resources to maintain current patterns of vegetation and land use, but these resources appear to be less and less available, indicating an approaching tipping point. Third, rapid sea level rise, for example from accelerated melting of the Greenland ice sheet, will create a choice between protection and abandonment for coastal regions throughout the world, a potential global tipping point comparable to those now faced by Arctic communities. The examples illustrate the basic idea that if costs of response increase more quickly than available resources, then society has fewer and fewer options as time passes.

Damage Tolerance of Sandwich Plates With Debonded Face Sheets

NASA Technical Reports Server (NTRS)

Sankar, Bhavani V.

2001-01-01

A nonlinear finite element analysis was performed to simulate axial compression of sandwich beams with debonded face sheets. The load - end-shortening diagrams were generated for a variety of specimens used in a previous experimental study. The energy release rate at the crack tip was computed using the J-integral, and plotted as a function of the load. A detailed stress analysis was performed and the critical stresses in the face sheet and the core were computed. The core was also modeled as an isotropic elastic-perfectly plastic material and a nonlinear post buckling analysis was performed. A Graeco-Latin factorial plan was used to study the effects of debond length, face sheet and core thicknesses, and core density on the load carrying capacity of the sandwich composite. It has been found that a linear buckling analysis is inadequate in determining the maximum load a debonded sandwich beam can carry. A nonlinear post-buckling analysis combined with an elastoplastic model of the core is required to predict the compression behavior of debonded sandwich beams.

Contact EPA Pacific Southwest (Region 9)

EPA Pesticide Factsheets

Contact EPA Region 9, Pacific Southwest: 24-hour report of violations and emergencies, environmental complaint tip line, Environmental Information Center, Library, Reception, Employee Locator, Media, Press, Public Affairs.

Anisotropic microporous supports impregnated with polymeric ion-exchange materials

DOEpatents

Friesen, D.; Babcock, W.C.; Tuttle, M.

1985-05-07

Novel ion-exchange media are disclosed, the media comprising polymeric anisotropic microporous supports containing polymeric ion-exchange or ion-complexing materials. The supports are anisotropic, having small exterior pores and larger interior pores, and are preferably in the form of beads, fibers and sheets. 5 figs.

Fermilab | Tevatron

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram Google+ YouTube Flickr

Fermilab | Contact Fermilab

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Tevatron experiments Tevatron operation Shutdown process For the media Video of shutdown event Guest book Cookies Quick Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter

Fermilab | About Fermilab

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Tevatron experiments Tevatron operation Shutdown process For the media Video of shutdown event Guest book Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram

Six Tips for College Health and Safety

MedlinePlus

... Emergency Preparedness & Response Environmental Health Healthy Living Injury, Violence & Safety Life Stages & Populations Travelers’ Health Workplace Safety & Health Features Media Sign up for Features Get Email Updates To ...

Tips to Prevent Illness from Clostridium Perfringens

MedlinePlus

... Emergency Preparedness & Response Environmental Health Healthy Living Injury, Violence & Safety Life Stages & Populations Travelers’ Health Workplace Safety & Health Features Media Sign up for Features Get Email Updates To ...

Using Current Resources to Implement Wellness Programming for Preschoolers

ERIC Educational Resources Information Center

Cirignano, Sherri M.

2013-01-01

Currently, there is a nationwide effort to include preschool-aged children in wellness efforts for the prevention of obesity. National resources include guidelines, best practices, and tip sheets to assist in the implementation of these interventions. The Let's Move! Child Care Checklist is a resource that can be used to assess the level at…

How to Identify Your Pest

Science.gov Websites

Pest Pest-specific Information (by name) Pest Control Tips Integrated Pest Management (IPM) Fact Sheets National Pesticide Information Center 1.800.858.7378 npic@ace.orst.edu We're open from 8:00AM to 12 Plants Pest Control Identify Your Pest Learn About Your Pest Control Your Pest Integrated Pest Management

Know Your Bottom Line: The Control of Your Auxiliaries.

ERIC Educational Resources Information Center

Stumph, Wayne J.

Designed to help college administrators read and understand accounting statements, this paper provides tips about danger signals that may be evident in financial statements and that may call for speedy action. The first statement examined is a balance sheet; i.e., a summation of all of the possessions and debts of a business or entity, which shows…

Back to the kitchen: food-grade agar is a low-cost alternative to bacteriological agar.

PubMed

Petrovski, Steve; Tillett, Daniel

2012-10-15

Food-grade agar can be used as a low-cost substitute for bacteriological agar in the preparation of solid microbial media. No difference was observed in the colony morphology, growth rate, or viability of bacteria grown on solid media prepared using food-grade agar as compared with using bacteriological-grade agar. This simple tip can reduce the cost of the most common solid media by 80% or more. Copyright © 2012 Elsevier Inc. All rights reserved.

Taking your conference experience to the next level with social media

NASA Astrophysics Data System (ADS)

Burk, John

2012-03-01

I enjoyed reading Jill Tennant's "Insider Conference Tips" ; however, I think she overlooked one thing that can make conferences even more useful and strengthen the connections you make between attendees—social media. Many conferences are finding themselves completely transformed by participants live-blogging and tweeting presentations, colleagues who haven't previously met arranging "meetups" via Twitter, and, perhaps most powerfully, using social media to allow those who can't be there in person at the conference to still participate.

Practical aspects of running DOE for improving growth media for in vitro plants

USDA-ARS?s Scientific Manuscript database

Experiments using DOE software to improve plant tissue culture growth medium are complicated and require complex setups. Once the experimental design is set and the treatment points calculated, media sheets and mixing charts must be developed. Since these experiments require three passages on the sa...

Four Argonne National Laboratory scientists receive Early Career Research

Science.gov Websites

Media Contacts Social Media Photos Videos Fact Sheets, Brochures and Reports Summer Science Writing Writing Internship Four Argonne National Laboratory scientists receive Early Career Research Program economic impact of cascading shortages. He will also seek to enable scaling on high-performance computing

Fermilab | Science at Fermilab | Computing

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium , Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact

Fermilab | Tritium at Fermilab | Indian Creek Results

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram

Fermilab | Tritium at Fermilab | Indian Creek Results

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram Google

Fermilab | Science | Inquiring Minds

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Office of Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at

Fermilab | Tevatron | Tevatron Operation

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium , Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact

Fermilab | Visit Fermilab

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Tevatron experiments Tevatron operation Shutdown process For the media Video of shutdown event Guest book check on holiday hours or check the Lederman Science Center website. Groups of six or more must book a

Fermilab | Tritium at Fermilab

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Energy Office of Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book

Fermilab | Science at Fermilab | Computing | Grid Computing

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram Google+ YouTube Flickr

Fermilab | Tevatron | Experiments | DZero

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram Google+ YouTube Flickr

Fermilab | Science at Fermilab | Computing | Networking

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram

Fermilab | Resources for

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Tevatron experiments Tevatron operation Shutdown process For the media Video of shutdown event Guest book Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For

Fermilab | Tevatron | Tevatron Symposium | Agenda

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For Industry

Fermilab | Tevatron | Tevatron Symposium

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Energy Office of Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book

Fermilab | Visit Fermilab | Tours, Programs and Events

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Quick Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter

Fermilab | Contact Fermilab | Email Fermilab

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Tevatron experiments Tevatron operation Shutdown process For the media Video of shutdown event Guest book , Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact

Fermilab | Tevatron | Shutdown Process

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For

Fermilab | Physics for Everyone | Lecture Series

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram Google+ YouTube Flickr

Fermilab | Science | Particle Physics

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Quick Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter

Fermilab | Visit Fermilab | Transportation

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram Google+ YouTube Flickr

Beyond the Book: Technology Integration into the Secondary School Library Media Curriculum. Library and Information Problem-Solving Skills Series.

ERIC Educational Resources Information Center

Doggett, Sandra L.

After exploring the pros and cons of using various technologies in secondary schools, as well as the development of an Acceptable Use Policy, this book describes how technology affects the role and interaction of media specialists, teachers, students, administrators, and parents. Technology planning tips are given on methods to research trends,…

Bird on a Wire

ERIC Educational Resources Information Center

Ward, Brad J.

2010-01-01

Since its launch in 2006, the social media tool Twitter has grown from a "wait-and-see" communications site to a mainstream media darling. Last year was the tipping point for this site, which is as easy to use as it is to confuse. As its popularity has grown, there has been a shift in the way Twitter is used. Early Twitter adopters would follow…

Effect of a large-sized silicone sheet upon recovery of mastoid aeration after mastoidectomy.

PubMed

Kazama, Kyosuke; Takahashi, Haruo; Kaieda, Satoru; Iwanaga, Tetsu; Yamamoto-Fukuda, Tomomi; Yoshida, Haruo; Kumagami, Hidetaka; Takasaki, Kenji

2008-06-01

To evaluate the effect of our large-sized silicone sheet upon postoperative recovery of mastoid aeration in ears after surgery including mastoidectomy and soft-wall reconstruction (SWR). Retrospective chart review in a tertiary care center. Recovery of mastoid aeration was assessed by CT 4 to 12 months after surgery on 72 ears (69 patients), in which the silicone sheet covering from the eustachian tube (ET) to the mastoid was placed after SWR procedure with mastoidectomy were done for their chronic otitis media. Results were compared with those with a small silicone sheet. Recovery of mastoid aeration was significantly better in the large-silicone-sheet group than in the small-silicone-sheet group (chi(2) value = 11.7146, P = 0.0006). This preliminary study suggested that our large-sized silicone sheet may be effective for postoperative recovery of mastoid aeration even in ears operated with SWR procedure.

Stiff Hands

MedlinePlus

... Stiff Hands Find a hand surgeon near you. Videos Figures Figure 1: Hand splint to help straighten ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Thumb Arthritis

MedlinePlus

... and Recovery Find a hand surgeon near you. Videos Thumb Arthritis Close Popup Figures Figure 1 - Basal ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Wrist Fractures

MedlinePlus

... Wrist Fractures Find a hand surgeon near you. Videos Wrist Fractures Close Popup Figures Figure 1 - Wrist ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Thumb Sprains

MedlinePlus

... Thumb Sprains Find a hand surgeon near you. Videos Figures Figure 1: The ulnar collateral ligament (UCL) ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Hand Therapy

MedlinePlus

... a scar Find a hand surgeon near you. Videos Figures Figure 1: Examples of hand splints PDF ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Ganglion Cysts

MedlinePlus

... Ganglion Cysts Find a hand surgeon near you. Videos Ganglion Cysts Close Popup Figures Figure 1 - Ganglion ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Fingertip Injuries

MedlinePlus

... the Hand. Find a hand surgeon near you. Videos Figures Figure 1: Fingertip anatomy PDF Fingertip Injury ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Hand Fractures

MedlinePlus

... Hand Fractures Find a hand surgeon near you. Videos Hand Fractures Close Popup Figures Figure 1 - Examples ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Control of Flap Vortices

NASA Technical Reports Server (NTRS)

Greenblatt, David

2005-01-01

A wind tunnel investigation was carried out on a semi-span wing model to assess the feasibility of controlling vortices emanating from outboard flaps and tip-flaps by actively varying the degree of boundary layer separation. Separation was varied by means of perturbations produced from segmented zero-efflux oscillatory blowing slots, while estimates of span loadings and vortex sheet strengths were obtained by integrating wing surface pressures. These estimates were used as input to inviscid rollup relations as a means of predicting changes to the vortex characteristics resulting from the perturbations. Surveys of flow in the wake of the outboard and tip-flaps were made using a seven-hole probe, from which the vortex characteristics were directly deduced. Varying the degree of separation had a marked effect on vortex location, strength, tangential velocity, axial velocity and size for both outboard and tip-flaps. Qualitative changes in vortex characteristics were well predicted by the inviscid rollup relations, while the failure to account for viscosity was presumed to be the main reason for observed discrepancies. Introducing perturbations near the outboard flap-edges or on the tip-flap exerted significant control over vortices while producing negligible lift excursions.

Extensor Tendon Injuries

MedlinePlus

... the Hand. Find a hand surgeon near you. Videos Figures Figure 1 - Extensor tendons, located on the ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Amputation and Prosthetics

MedlinePlus

... Extremity Prosthetics Find a hand surgeon near you. Videos Figures Figure 1: Thumb Prosthesis - not attached Figure ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Tendon Transfer Surgery

MedlinePlus

... Transfer Surgery Find a hand surgeon near you. Videos Figures Figure 2: Example of Tendon Transfer surgery ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Nail Bed Injuries

MedlinePlus

... and Treatment Find a hand surgeon near you. Videos Figures Figure 1: The anatomy of the nail ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Hand Surgery: Anesthesia

MedlinePlus

... To * DESCRIPTION Find a hand surgeon near you. Videos Figures Figure 1: Diagram of the regional blocks ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Cubital Tunnel Syndrome

MedlinePlus

... Tunnel Syndrome Find a hand surgeon near you. Videos Cubital Tunnel Syndrome Close Popup Figures Figure 1 - ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Flexor Tendon Injuries

MedlinePlus

... the Hand. Find a hand surgeon near you. Videos Figures Figure 1 -The tendons of the hand ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Tsunamis

MedlinePlus

... Extreme Heat Older Adults (Aged 65+) Infants and Children Chronic Medical Conditions Low Income Athletes Outdoor Workers Pets Hot Weather Tips Warning Signs and Symptoms FAQs Social Media How to Stay Cool Missouri Cooling Centers Extreme ...

Volcanoes

MedlinePlus

... Extreme Heat Older Adults (Aged 65+) Infants and Children Chronic Medical Conditions Low Income Athletes Outdoor Workers Pets Hot Weather Tips Warning Signs and Symptoms FAQs Social Media How to Stay Cool Missouri Cooling Centers Extreme ...

Developing a healthy web-based cookbook for pediatric cancer patients and survivors: rationale and methods.

PubMed

Li, Rhea; Raber, Margaret; Chandra, Joya

2015-03-31

Obesity has been a growing problem among children and adolescents in the United States for a number of decades. Childhood cancer survivors (CCS) are more susceptible to the downstream health consequences of obesity such as cardiovascular disease, endocrine issues, and risk of cancer recurrence due to late effects of treatment and suboptimal dietary and physical activity habits. The objective of this study was to document the development of a Web-based cookbook of healthy recipes and nutrition resources to help enable pediatric cancer patients and survivors to lead healthier lifestyles. The Web-based cookbook, named "@TheTable", was created by a committee of researchers, a registered dietitian, patients and family members, a hospital chef, and community advisors and donors. Recipes were collected from several sources including recipe contests and social media. We incorporated advice from current patients, parents, and CCS. Over 400 recipes, searchable by several categories and with accompanying nutritional information, are currently available on the website. In addition to healthy recipes, social media functionality and cooking videos are integrated into the website. The website also features nutrition information resources including nutrition and cooking tip sheets available on several subjects. The "@TheTable" website is a unique resource for promoting healthy lifestyles spanning pediatric oncology prevention, treatment, and survivorship. Through evaluations of the website's current and future use, as well as incorporation into interventions designed to promote energy balance, we will continue to adapt and build this unique resource to serve cancer patients, survivors, and the general public.

Developing a Healthy Web-Based Cookbook for Pediatric Cancer Patients and Survivors: Rationale and Methods

PubMed Central

Raber, Margaret

2015-01-01

Background Obesity has been a growing problem among children and adolescents in the United States for a number of decades. Childhood cancer survivors (CCS) are more susceptible to the downstream health consequences of obesity such as cardiovascular disease, endocrine issues, and risk of cancer recurrence due to late effects of treatment and suboptimal dietary and physical activity habits. Objective The objective of this study was to document the development of a Web-based cookbook of healthy recipes and nutrition resources to help enable pediatric cancer patients and survivors to lead healthier lifestyles. Methods The Web-based cookbook, named “@TheTable”, was created by a committee of researchers, a registered dietitian, patients and family members, a hospital chef, and community advisors and donors. Recipes were collected from several sources including recipe contests and social media. We incorporated advice from current patients, parents, and CCS. Results Over 400 recipes, searchable by several categories and with accompanying nutritional information, are currently available on the website. In addition to healthy recipes, social media functionality and cooking videos are integrated into the website. The website also features nutrition information resources including nutrition and cooking tip sheets available on several subjects. Conclusions The “@TheTable” website is a unique resource for promoting healthy lifestyles spanning pediatric oncology prevention, treatment, and survivorship. Through evaluations of the website’s current and future use, as well as incorporation into interventions designed to promote energy balance, we will continue to adapt and build this unique resource to serve cancer patients, survivors, and the general public. PMID:25840596

Tensiometer methods

DOEpatents

Grover, Blair K.; Hubbell, Joel M.; Sisson, James B.; Casper, William L.

2005-12-20

A method for collecting data regarding a matric potential of a media includes providing a tensiometer having a stainless steel tensiometer casing, the stainless steel tensiometer casing comprising a tip portion which includes a wetted porous stainless steel membrane through which a matric potential of a media is sensed; driving the tensiometer into the media using an insertion tube comprising a plurality of probe casing which are selectively coupled to form the insertion tube as the tensiometer is progressively driven deeper into the media, wherein the wetted porous stainless steel membrane is in contact with the media; and sensing the matric potential the media exerts on the wetted porous stainless steel membrane by a pressure sensor in fluid hydraulic connection with the porous stainless steel membrane. A tensiometer includes a stainless steel casing.

Healthy Vision Tips

MedlinePlus

... You may have heard that eating carrots is good for eyes. That’s true, but other foods like spinach, kale, salmon, ... Social Media Information in Spanish (Información en español) Website, Social ...

Hands in Systemic Disease

MedlinePlus

... Systemic Diseases Find a hand surgeon near you. Videos Figures Figure 1 - Arthritic Swelling Figure 10 - Pyogenic ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Gout and Pseudogout

MedlinePlus

... the Hand. Find a hand surgeon near you. Videos Figures Figure 1 – Acute gout episode with a ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Trigger Finger (Stenosing Tenosynovitis)

MedlinePlus

... Trigger Finger Find a hand surgeon near you. Videos Trigger Finger Animation Trigger Finger Close Popup Close ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Hot Weather Tips

MedlinePlus

... Caregiver Stories Connections e-Newsletter Research Registry FCA+(plus) Services Press Media Kit What’s New FCA Blog ... person plenty of water and fruit or vegetable juice even if they say they’re not thirsty. ...

Microstructure and Mechanical Performance of Friction Stir Spot-Welded Aluminum-5754 Sheets

NASA Astrophysics Data System (ADS)

Pathak, N.; Bandyopadhyay, K.; Sarangi, M.; Panda, Sushanta Kumar

2013-01-01

Friction stir spot welding (FSSW) is a recent trend of joining light-weight sheet metals while fabricating automotive and aerospace body components. For the successful application of this solid-state welding process, it is imperative to have a thorough understanding of the weld microstructure, mechanical performance, and failure mechanism. In the present study, FSSW of aluminum-5754 sheet metal was tried using tools with circular and tapered pin considering different tool rotational speeds, plunge depths, and dwell times. The effects of tool design and process parameters on temperature distribution near the sheet-tool interface, weld microstructure, weld strength, and failure modes were studied. It was found that the peak temperature was higher while welding with a tool having circular pin compared to tapered pin, leading to a bigger dynamic recrystallized stir zone (SZ) with a hook tip bending towards the upper sheet and away from the keyhole. Hence, higher lap shear separation load was observed in the welds made from circular pin compared to those made from tapered pin. Due to influence of size and hardness of SZ on crack propagation, three different failure modes of weld nugget were observed through optical cross-sectional micrograph and SEM fractographs.

Social networks uncovered: 10 tips every plastic surgeon should know.

PubMed

Dauwe, Phillip; Heller, Justin B; Unger, Jacob G; Graham, Darrell; Rohrich, Rod J

2012-11-01

Understanding online social networks is of critical importance to the plastic surgeon. With knowledge, it becomes apparent that the numerous networks available are similar in their structure, usage, and function. The key is communication between Internet media such that one maximizes exposure to patients. This article focuses on 2 social networking platforms that we feel provide the most utility to plastic surgeons. Ten tips are provided for incorporation of Facebook and Twitter into your practice.

Fermilab | Science | Fermilab and the Higgs Boson

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For Industry

Fermilab | Tritium at Fermilab | Tritium in Surface Water

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram Google

Fermilab | Science | Particle Accelerators | LHC and Future Accelerators

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Office of Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at

Fermilab | Tritium at Fermilab | Tritium in Sanitary Sewers

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram Google

Fermilab | Tritium at Fermilab | Kress Creek Results

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For

Fermilab | Tevatron | Tevatron Symposium | Organizing Committee

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium , Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact

Fermilab | Tevatron | Tevatron Symposium | Travel and Lodging

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Office of Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at

Fermilab | Science | Particle Accelerators | Fermilab's Accelerator Complex

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For

Fermilab | Tritium at Fermilab | Indian Creek Aerial View

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Office of Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at

Fermilab | Science | Inquiring Minds | Questions About Physics

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For

Fermilab | Tritium at Fermilab | Kress Creek Aerial View

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For Industry

Fermilab | Science | Particle Physics | Benefits of Particle Physics

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram Google

Fermilab | Science | Questions for the Universe

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For

Fermilab | Tritium at Fermilab | Ferry Creek Aerial View

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For Industry

Fermilab | Science at Fermilab | Computing | Mass Storage

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Symposium Cookies Quick Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter

Aerosol Filter Loading Data for a Simulated Jet Engine Test Cell Aerosol.

DTIC Science & Technology

1979-08-01

media. M SECTION II TEST PROGRAM I. TESTING PROCEDURE Sheets of the filter media were obtained from Owens - Corning Fiberglas Corporation. Ten centimeter...loading cycle. 2. TEST FILTERS The four following glass fiber filter medias were obtained from Owens - Corning Fiberglas Corporation (OCF) and tested both...shown in Table 22. Filters were washed from the back side. 5. ONCLUSIONS Four glass fiber filters, specified in the contract, were obtained from Owens

Burn Wise Awareness Kit

EPA Pesticide Factsheets

Health and safety outreach materials in the form of an awareness kit. Designed specifically for state, local, and tribal air agencies working to reduce wood smoke pollution, it includes best burn tips, social media m

First Aid Tips

MedlinePlus

... is to “conduct and support research, training, health information dissemination, and other programs with respect to blinding eye ... Media Policies and Other Important Links NEI Employee Emergency Information NEI Intranet (Employees Only) *PDF files require ...

Choking and Strangulation Prevention Tips

MedlinePlus

... away from children. These include magnets found in construction sets, children's toys or stress-relieving adult desk ... with Us Donate Join Our Mailing List Global Road Safety Sponsors Recalls Media Center Blog Videos Newsletter ...

Animal Bites of the Hand

MedlinePlus

... animal bite Find a hand surgeon near you. Videos Figures Figure 1: Finger infection from cat bite ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Replantation (Finger, Hand, or Arm)

MedlinePlus

... is Replantation? Find a hand surgeon near you. Videos Figures Figure 1: Replantation refers to the surgical ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Experimental analysis of the sheet metal forming behavior of newly developed press hardening steels

NASA Astrophysics Data System (ADS)

Meza-García, Enrique; Kräusel, Verena; Landgrebe, Dirk

2018-05-01

The aim of this work was the characterization of the newly developed press hardening sheet alloys 1800 PHS and 2000 PHS developed by SSAB with regard to their hot forming behavior on the basis of the experimental determination of relevant mechanical and technological properties. For this purpose conventional and non-conventional sheet metal testing methods were used. To determine the friction coefficient, the strip drawing test was applied, while the deep drawing cup test was used to determine the maximum draw depth. Finally, a V-bending test was carried out to evaluate the springback behavior of the investigated alloys by varying the blank temperature and quenching media. This work provides a technological guideline for the production of press hardened sheet parts made of these investigated sheet metals.

Melasma: Tips for Managing

MedlinePlus

... Us Media contacts Advertising contacts AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2018 American Academy ... prohibited without prior written permission. AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2017 American Academy ...

Tips for Healthy Nails

MedlinePlus

... Us Media contacts Advertising contacts AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2018 American Academy ... prohibited without prior written permission. AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2017 American Academy ...

Tips for Relieving Dry Skin

MedlinePlus

... Us Media contacts Advertising contacts AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2018 American Academy ... prohibited without prior written permission. AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2017 American Academy ...

Tips for Healthy Hair

MedlinePlus

... Us Media contacts Advertising contacts AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2018 American Academy ... prohibited without prior written permission. AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2017 American Academy ...

Nerve Injuries of the Upper Extremity

MedlinePlus

... Upper Extremity Find a hand surgeon near you. Videos Figures Figure 1 - Nerve with bundles of individual ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Health Effects of Tsunamis

MedlinePlus

... Extreme Heat Older Adults (Aged 65+) Infants and Children Chronic Medical Conditions Low Income Athletes Outdoor Workers Pets Hot Weather Tips Warning Signs and Symptoms FAQs Social Media How to Stay Cool Missouri Cooling Centers Extreme ...

Trench Foot or Immersion Foot

MedlinePlus

... Extreme Heat Older Adults (Aged 65+) Infants and Children Chronic Medical Conditions Low Income Athletes Outdoor Workers Pets Hot Weather Tips Warning Signs and Symptoms FAQs Social Media How to Stay Cool Missouri Cooling Centers Extreme ...

Progressive failure of sheeted rock slopes: the 2009–2010 Rhombus Wall rock falls in Yosemite Valley, California, USA

USGS Publications Warehouse

Stock, Greg M.; Martel, Stephen J.; Collins, Brian D.; Harp, Edwin L.

2012-01-01

Progressive rock-fall failures in natural rock slopes are common in many environments, but often elude detailed quantitative documentation and analysis. Here we present high-resolution photography, video, and laser scanning data that document spatial and temporal patterns of a 15-month-long sequence of at least 14 rock falls from the Rhombus Wall, a sheeted granitic cliff in Yosemite Valley, California. The rock-fall sequence began on 26 August 2009 with a small failure at the tip of an overhanging rock slab. Several hours later, a series of five rock falls totaling 736 m3progressed upward along a sheeting joint behind the overhanging slab. Over the next 3 weeks, audible cracking occurred on the Rhombus Wall, suggesting crack propagation, while visual monitoring revealed opening of a sheeting joint adjacent to the previous failure surface. On 14 September 2009 a 110 m3 slab detached along this sheeting joint. Additional rock falls between 30 August and 20 November 2010, totaling 187 m3, radiated outward from the initial failure area along cliff (sub)parallel sheeting joints. We suggest that these progressive failures might have been related to stress redistributions accompanying propagation of sheeting joints behind the cliff face. Mechanical analyses indicate that tensile stresses should occur perpendicular to the cliff face and open sheeting joints, and that sheeting joints should propagate parallel to a cliff face from areas of stress concentrations. The analyses also account for how sheeting joints can propagate to lengths many times greater than their depths behind cliff faces. We posit that as a region of failure spreads across a cliff face, stress concentrations along its margin will spread with it, promoting further crack propagation and rock falls.

Antarctic climate and ice-sheet configuration during the early Pliocene interglacial at 4.23 Ma

NASA Astrophysics Data System (ADS)

Golledge, Nicholas R.; Thomas, Zoë A.; Levy, Richard H.; Gasson, Edward G. W.; Naish, Timothy R.; McKay, Robert M.; Kowalewski, Douglas E.; Fogwill, Christopher J.

2017-07-01

The geometry of Antarctic ice sheets during warm periods of the geological past is difficult to determine from geological evidence, but is important to know because such reconstructions enable a more complete understanding of how the ice-sheet system responds to changes in climate. Here we investigate how Antarctica evolved under orbital and greenhouse gas conditions representative of an interglacial in the early Pliocene at 4.23 Ma, when Southern Hemisphere insolation reached a maximum. Using offline-coupled climate and ice-sheet models, together with a new synthesis of high-latitude palaeoenvironmental proxy data to define a likely climate envelope, we simulate a range of ice-sheet geometries and calculate their likely contribution to sea level. In addition, we use these simulations to investigate the processes by which the West and East Antarctic ice sheets respond to environmental forcings and the timescales over which these behaviours manifest. We conclude that the Antarctic ice sheet contributed 8.6 ± 2.8 m to global sea level at this time, under an atmospheric CO2 concentration identical to present (400 ppm). Warmer-than-present ocean temperatures led to the collapse of West Antarctica over centuries, whereas higher air temperatures initiated surface melting in parts of East Antarctica that over one to two millennia led to lowering of the ice-sheet surface, flotation of grounded margins in some areas, and retreat of the ice sheet into the Wilkes Subglacial Basin. The results show that regional variations in climate, ice-sheet geometry, and topography produce long-term sea-level contributions that are non-linear with respect to the applied forcings, and which under certain conditions exhibit threshold behaviour associated with behavioural tipping points.

Developing a Cookbook with Lifestyle Tips: A Community-Engaged Approach to Promoting Diet-Related Cancer Prevention Guidelines.

PubMed

Smith, Selina A; Sheats, Joyce Q; Whitehead, Mary S; Delmoor, Ernestine; Britt, Thomas; Harris, Cassandra L; Robinson-Flint, Janette; Porche-Smith, L Monique; Umeakunne, Kayellen Edmonds; Coughlin, Steven S

Supplementing nutrition education with skills-building activities may enhance community awareness of diet-related cancer prevention guidelines. To develop a cookbook with lifestyle tips, recipes were solicited from the National Black Leadership Initiative on Cancer (NBLIC) community coalitions and dietary intake advice from participants in the Educational Program to Increase Colorectal Cancer Screening (EPICS). With guidance from a chef and registered dietitian, recipes were tested, assessed, and transformed; lifestyle advice was obtained from focus groups. The cookbook with lifestyle tips, named "Down Home Healthy Living (DHHL) 2.0," was distributed in print form to 2,500 EPICS participants and shared electronically through websites and social media.

Developing a Cookbook with Lifestyle Tips: A Community-Engaged Approach to Promoting Diet-Related Cancer Prevention Guidelines

PubMed Central

Smith, Selina A.; Sheats, Joyce Q.; Whitehead, Mary S.; Delmoor, Ernestine; Britt, Thomas; Harris, Cassandra L.; Robinson-Flint, Janette; Porche-Smith, L. Monique; Umeakunne, Kayellen Edmonds; Coughlin, Steven S.

2015-01-01

Supplementing nutrition education with skills-building activities may enhance community awareness of diet-related cancer prevention guidelines. To develop a cookbook with lifestyle tips, recipes were solicited from the National Black Leadership Initiative on Cancer (NBLIC) community coalitions and dietary intake advice from participants in the Educational Program to Increase Colorectal Cancer Screening (EPICS). With guidance from a chef and registered dietitian, recipes were tested, assessed, and transformed; lifestyle advice was obtained from focus groups. The cookbook with lifestyle tips, named “Down Home Healthy Living (DHHL) 2.0,” was distributed in print form to 2,500 EPICS participants and shared electronically through websites and social media. PMID:26709388

Crack-tip-opening angle measurements and crack tunneling under stable tearing in thin sheet 2024-T3 aluminum alloy

NASA Technical Reports Server (NTRS)

Dawicke, D. S.; Sutton, M. A.

1993-01-01

The stable tearing behavior of thin sheets 2024-T3 aluminum alloy was studied for middle crack tension specimens having initial cracks that were: flat cracks (low fatigue stress) and 45 degrees through-thickness slant cracks (high fatigue stress). The critical crack-tip-opening angle (CTOA) values during stable tearing were measured by two independent methods, optical microscopy and digital image correlation. Results from the two methods agreed well. The CTOA measurements and observations of the fracture surfaces showed that the initial stable tearing behavior of low and high fatigue stress tests is significantly different. The cracks in the low fatigue stress tests underwent a transition from flat-to-slant crack growth, during which the CTOA values were high and significant crack tunneling occurred. After crack growth equal to about the thickness, CTOA reached a constant value of 6 deg and after crack growth equal to about twice the thickness, crack tunneling stabilized. The initial high CTOA values, in the low fatigue crack tests, coincided with large three-dimensional crack front shape changes due to a variation in the through-thickness crack tip constraint. The cracks in the high fatigue stress tests reach the same constant CTOA value after crack growth equal to about the thickness, but produced only a slightly higher CTOA value during initial crack growth. For crack growth on the 45 degree slant, the crack front and local field variables are still highly three-dimensional. However, the constant CTOA values and stable crack front shape may allow the process to be approximated with two-dimensional models.

Imaging Electron Motion in a Few Layer MoS2 Device

NASA Astrophysics Data System (ADS)

Bhandari, S.; Wang, K.; Watanabe, K.; Taniguchi, T.; Kim, P.; Westervelt, R. M.

2017-06-01

Ultrathin sheets of MoS2 are a newly discovered 2D semiconductor that holds great promise for nanoelectronics. Understanding the pattern of current flow will be crucial for developing devices. In this talk, we present images of current flow in MoS2 obtained with a Scanned Probe Microscope (SPM) cooled to 4 K. We previously used this technique to image electron trajectories in GaAs/AlGaAs heterostructures and graphene. The charged SPM tip is held just above the sample surface, creating an image charge inside the device that scatters electrons. By measuring the change in resistance ΔR while the tip is raster scanned above the sample, an image of electron flow is obtained. We present images of electron flow in an MoS2 device patterned into a hall bar geometry. A three-layer MoS2 sheet is encased by two hBN layers, top and bottom, and patterned into a hall-bar with multilayer graphene contacts. An SPM image shows the current flow pattern from the wide contact at the end of the device for a Hall density n = 1.3×1012 cm-2. The SPM tip tends to block flow, increasing the resistance R. The pattern of flow was also imaged for a narrow side contact on the sample. At density n = 5.4×1011 cm-2; the pattern seen in the SPM image is similar to the wide contact. The ability to image electron flow promises to be very useful for the development of ultrathin devices from new 2D materials.

Fe doped TiO2 nanofibers on the surface of graphene sheets for photovoltaics applications

NASA Astrophysics Data System (ADS)

Farhangi, Nasrin; Medina-Gonzalez, Yaocihuatl; Charpentier, Paul A.

2011-08-01

Highly ordered, visible light driven TiO2 nanowire arrays doped with Fe photocatalysts were grown on the surface of functionalized graphene sheets (FGSs) using a sol-gel method with titanium isopropoxide (TIP) monomer, acetic acid (HAc) as the polycondensation agent and iron chloride in the green solvent, supercritical carbon dioxide (scCO2). The morphology of the synthesized materials was studied by SEM and TEM, which showed uniform formation of Fe doped TiO2 nanofibers on the surface of graphene sheets, which acted as a template for nanowire growth through surface -COOH functionalities. Increasing Fe content in the nanowires did not change the morphology significantly. Optical properties of the synthesized composites were examined by UV spectroscopy which showed a significant reduction in band gap with increasing Fe content, i.e. 2.25 eV at 0.6% Fe. The enhancement of the optical properties of synthesized materials was confirmed by photocurrent measurement. The optimum sample containing 0.6% Fe doped TiO2 on the graphene sheets increased the power conversation efficiency by 6-fold in comparison to TiO2 alone.

Back-to-School Guide: Jump-Start Learning with New Media. Updated with New Tools and Resources for 2010-11

ERIC Educational Resources Information Center

George Lucas Educational Foundation, 2010

2010-01-01

To help teachers get off to a good start, this paper presents the updated "Back-to-School Guide" that is brimming with new-media ideas and resources. It outlines ten tips, along with easy-to-use tools, that will help teachers build their classroom community, survey students to bring out their ideas, and make learning more collaborative. Links to…

Exploring Media Processes and Project Applications: Rediscovering Shrinky Dinks

ERIC Educational Resources Information Center

Wolf Bordonaro, Gaelynn P.; Blake, Ann; Corrington, Deborah; Fanders, Tegan; Morley, Lauren

2009-01-01

Shrinky Dinks[R] are a plastic-sheet material that shrinks, hardens and thickens when heated in a traditional or toaster oven. The material was a favorite of generations, but many contemporary students and professionals in art have never had the opportunity to play with the unique media. This article discusses Shrinky Dinks and the importance of…

Tensiometer methods and apparatus

DOEpatents

Grover, Blair K.; Hubbell, Joel M.; Sisson, James B.; Casper, William L.

2004-08-10

A method for collecting data regarding a matric potential of a media includes providing a tensiometer having a stainless steel tensiometer casing, the stainless steel tensiometer casing comprising a tip portion which includes a wetted porous stainless steel membrane through which a matric potential of a media is sensed; driving the tensiometer into the media using an insertion tube comprising a plurality of probe casing which are selectively coupled to form the insertion tube as the tensiometer is progressively driven deeper into the media, wherein the wetted porous stainless steel membrane is in contact with the media; and sensing the matric potential the media exerts on the wetted porous stainless steel membrane by a pressure sensor in fluid hydraulic connection with the porous stainless steel membrane. A tensiometer includes a stainless steel casing.

African-American Hair: Tips for Everyday Care

MedlinePlus

... Us Media contacts Advertising contacts AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2018 American Academy ... prohibited without prior written permission. AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2017 American Academy ...

Golf Injuries to the Hand, Wrist, or Elbow

MedlinePlus

... golf injuries Find a hand surgeon near you. Videos Figures Figure 1: Elbow showing muscles as they ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Skin Cancer of the Hand and Upper Extremity

MedlinePlus

... the Hand. Find a hand surgeon near you. Videos Figures Figure 1 - Squamous cell carcinoma with small ... or "in." Also, avoid using media types like "video," "article," and "picture." Tip 4: Your results can ...

Optimization of the Ussing chamber setup with excised rat intestinal segments for dissolution/permeation experiments of poorly soluble drugs.

PubMed

Forner, Kristin; Roos, Carl; Dahlgren, David; Kesisoglou, Filippos; Konerding, Moritz A; Mazur, Johanna; Lennernäs, Hans; Langguth, Peter

2017-02-01

Prediction of the in vivo absorption of poorly soluble drugs may require simultaneous dissolution/permeation experiments. In vivo predictive media have been modified for permeation experiments with Caco-2 cells, but not for excised rat intestinal segments. The present study aimed at improving the setup of dissolution/permeation experiments with excised rat intestinal segments by assessing suitable donor and receiver media. The regional compatibility of rat intestine in Ussing chambers with modified Fasted and Fed State Simulated Intestinal Fluids (Fa/FeSSIF mod ) as donor media was evaluated via several parameters that reflect the viability of the excised intestinal segments. Receiver media that establish sink conditions were investigated for their foaming potential and toxicity. Dissolution/permeation experiments with the optimized conditions were then tested for two particle sizes of the BCS class II drug aprepitant. Fa/FeSSIF mod were toxic for excised rat ileal sheets but not duodenal sheets, the compatibility with jejunal segments depended on the bile salt concentration. A non-foaming receiver medium containing bovine serum albumin (BSA) and Antifoam B was nontoxic. With these conditions, the permeation of nanosized aprepitant was higher than of the unmilled drug formulations. The compatibility of Fa/FeSSIF mod depends on the excised intestinal region. The chosen conditions enable dissolution/permeation experiments with excised rat duodenal segments. The experiments correctly predicted the superior permeation of nanosized over unmilled aprepitant that is observed in vivo. The optimized setup uses FaSSIF mod as donor medium, excised rat duodenal sheets as permeation membrane and a receiver medium containing BSA and Antifoam B.

Detection of Steel Fatigue Cracks with Strain Sensing Sheets Based on Large Area Electronics

PubMed Central

Yao, Yao; Glisic, Branko

2015-01-01

Reliable early-stage damage detection requires continuous monitoring over large areas of structure, and with sensors of high spatial resolution. Technologies based on Large Area Electronics (LAE) can enable direct sensing and can be scaled to the level required for Structural Health Monitoring (SHM) of civil structures and infrastructure. Sensing sheets based on LAE contain dense arrangements of thin-film strain sensors, associated electronics and various control circuits deposited and integrated on a flexible polyimide substrate that can cover large areas of structures. This paper presents the development stage of a prototype strain sensing sheet based on LAE for crack detection and localization. Two types of sensing-sheet arrangements with size 6 × 6 inch (152 × 152 mm) were designed and manufactured, one with a very dense arrangement of sensors and the other with a less dense arrangement of sensors. The sensing sheets were bonded to steel plates, which had a notch on the boundary, so the fatigue cracks could be generated under cyclic loading. The sensors within the sensing sheet that were close to the notch tip successfully detected the initialization of fatigue crack and localized the damage on the plate. The sensors that were away from the crack successfully detected the propagation of fatigue cracks based on the time history of the measured strain. The results of the tests have validated the general principles of the proposed sensing sheets for crack detection and identified advantages and challenges of the two tested designs. PMID:25853407

SELF-MANAGEMENT COUNSELING IN PATIENTS WITH HEART FAILURE: PRIMARY RESULTS FROM THE HEART FAILURE ADHERENCE AND RETENTION TRIAL (HART)

PubMed Central

Powell, Lynda H.; Calvin, James E.; Richardson, Dejuran; Janssen, Imke; Mendes de Leon, Carlos F.; Flynn, Kristin J.; Grady, Kathleen L.; Rucker-Whitaker, Cheryl S.; Eaton, Claudia; Avery, Elizabeth

2013-01-01

Context Activating patients with heart failure (HF) to adhere to physician advice has not translated into clinical benefit, but past trials have had methodologic limitations. Objective To determine the value of self-management counseling plus HF education, over HF education alone, on the primary endpoint of death or HF hospitalization. Design, Setting, and Patients A single center behavioral efficacy trial in 902 patients with mild to moderate systolic or diastolic dysfunction, randomized between 2001–2004. Interventions All patients were offered 18 contacts and 18 HF educational tip sheets over the course of 1 year. Patients randomized to education received tip sheets in the mail and phone calls to check comprehension. Patients randomized to self-management received tip sheets in groups and were taught self-management skills to implement the advice. Main Outcome Measure Death or HF hospitalization, blindly adjudicated by cardiologists. Intent-to-treat results were analyzed as time-to-event and accelerated failure time models were used for non-proportional hazards. Results Patients were an average of 63.6 years, 47% female, 40% minority, 52% with family income <$30,000/year, and 23% with diastolic dysfunction. The self-management arm was no different from the education arm on the primary endpoint (Wilcoxon p=0.58). Post-hoc analyses on pre-specified subgroups revealed a significant income x treatment interaction (log-logistic estimate=0.64, p=0.02). Patients with income <$30,000 in self-management had a slower time to event than those in education (p=0.05) and were no different than higher income patients in either treatment arm. Conclusions The addition of self-management counseling to HF education does not reduce death or HF hospitalizations in patients with mild to moderate HF. Future trials should evaluate tailored outpatient HF management featuring ongoing education and comprehension checks for all, augmented by group-based skill development for those more economically disadvantaged. Such an approach may be a cost-effective, timely, and simple option for reducing HF costs. PMID:20858878

Fractographic Observations on the Mechanism of Fatigue Crack Growth in Aluminium Alloys

NASA Astrophysics Data System (ADS)

Alderliesten, R. C.; Schijve, J.; Krkoska, M.

Special load histories are adopted to obtain information about the behavior of the moving crack tip during the increasing and decreasing part of a load cycle. It is associated with the crack opening and closure of the crack tip. Secondly, modern SEM techniques are applied for observations on the morphology of the fractures surfaces of a fatigue crack. Information about the cross section profiles of striations are obtained. Corresponding locations of the upper and the lower fracture surface are also explored in view of the crack extension mechanism. Most experiments are carried out on sheet specimens of aluminum alloys 2024-T3, but 7050-T7451 specimens are also tested in view of a different ductility of the two alloys.

Preparation of Caco-2 cell sheets using plasma polymerised acrylic acid as a weak boundary layer.

PubMed

Majani, Ruby; Zelzer, Mischa; Gadegaard, Nikolaj; Rose, Felicity R; Alexander, Morgan R

2010-09-01

The use of cell sheets for tissue engineering applications has considerable advantages over single cell seeding techniques. So far, only thermoresponsive surfaces have been used to manufacture cell sheets without chemically disrupting the cell-surface interactions. Here, we present a new and facile technique to prepare sheets of epithelial cells using plasma polymerised acrylic acid films. The cell sheets are harvested by gentle agitation of the media without the need of any additional external stimulus. We demonstrate that the plasma polymer deposition conditions affect the viability and metabolic activity of the cells in the sheet and relate these effects to the different surface properties of the plasma polymerised acrylic acid films. Based on surface analysis data, a first attempt is made to explain the mechanism behind the cell sheet formation. The advantage of the epithelial cell sheets generated here over single cell suspensions to seed a PLGA scaffold is presented. The scaffold itself, prepared using a mould fabricated via photolithography, exhibits a unique architecture that mimics closely the dimensions of the native tissue (mouse intestine). Copyright 2010 Elsevier Ltd. All rights reserved.

Optical modulator including grapene

DOEpatents

Liu, Ming; Yin, Xiaobo; Zhang, Xiang

2016-06-07

The present invention provides for a one or more layer graphene optical modulator. In a first exemplary embodiment the optical modulator includes an optical waveguide, a nanoscale oxide spacer adjacent to a working region of the waveguide, and a monolayer graphene sheet adjacent to the spacer. In a second exemplary embodiment, the optical modulator includes at least one pair of active media, where the pair includes an oxide spacer, a first monolayer graphene sheet adjacent to a first side of the spacer, and a second monolayer graphene sheet adjacent to a second side of the spacer, and at least one optical waveguide adjacent to the pair.

Propagation stability of self-reconstructing Bessel beams enables contrast-enhanced imaging in thick media.

PubMed

Fahrbach, Florian O; Rohrbach, Alexander

2012-01-17

Laser beams that can self-reconstruct their initial beam profile even in the presence of massive phase perturbations are able to propagate deeper into inhomogeneous media. This ability has crucial advantages for light sheet-based microscopy in thick media, such as cell clusters, embryos, skin or brain tissue or plants, as well as scattering synthetic materials. A ring system around the central intensity maximum of a Bessel beam enables its self-reconstruction, but at the same time illuminates out-of-focus regions and deteriorates image contrast. Here we present a detection method that minimizes the negative effect of the ring system. The beam's propagation stability along one straight line enables the use of a confocal line principle, resulting in a significant increase in image contrast. The axial resolution could be improved by nearly 100% relative to the standard light-sheet techniques using scanned Gaussian beams, while demonstrating self-reconstruction also for high propagation depths.

Pilot Study on the Prevalence of Imposed Queries in a School Library Media Center.

ERIC Educational Resources Information Center

Gross, Melissa

1997-01-01

Discussion of information-seeking behavior focuses on a study of the imposed query, as opposed to self-generated queries, in an elementary school library media center in order to quantify its presence, to record characteristics of the users that carry them, and to identify the persons imposing them. The coding sheet is appended. Contains one table…

Social media is all about video these days: tips communicating science from NASA's Earth Right Now

NASA Astrophysics Data System (ADS)

Bell, S.

2016-12-01

If you're not producing video to communicate your science findings, you're missing the boat navigating the ever-evolving currents of social media. NASA's Earth Right Now communications team made video a priority the past year as we engaged a massive online audience on social media. We will share best practices on social media, lessons learned, what's on the horizon and storytelling techniques to try. PBS documentary-style is passé. Welcome to the world of ten-second Snaps, text-on-picture CNN stories, Facebook Live events and 360° video experiences. Your audience is out there, you just need to catch their attention.

Social media use in nursing education.

PubMed

Schmitt, Terri L; Sims-Giddens, Susan S; Booth, Richard G

2012-09-30

As technological advances continue to expand connectivity and communication, the number of patients and nurses engaging in social media increases. Nurses play a significant role in identification, interpretation, and transmission of knowledge and information within healthcare. Social media is a platform that can assist nursing faculty in helping students to gain greater understanding of and/or skills in professional communication; health policy; patient privacy and ethics; and writing competencies. Although there are barriers to integration of social media within nursing education, there are quality resources available to assist faculty to integrate social media as a viable pedagogical method. This article discusses the background and significance of social media tools as pedagogy, and provides a brief review of literature. To assist nurse educators who may be using or considering social media tools, the article offers selected examples of sound and pedagogically functional use in course and program applications; consideration of privacy concerns and advantages and disadvantages; and tips for success.

Bridged graphite oxide materials

NASA Technical Reports Server (NTRS)

Herrera-Alonso, Margarita (Inventor); McAllister, Michael J. (Inventor); Aksay, Ilhan A. (Inventor); Prud'homme, Robert K. (Inventor)

2010-01-01

Bridged graphite oxide material comprising graphite sheets bridged by at least one diamine bridging group. The bridged graphite oxide material may be incorporated in polymer composites or used in adsorption media.

Developing physics learning media using 3D cartoon

NASA Astrophysics Data System (ADS)

Wati, M.; Hartini, S.; Hikmah, N.; Mahtari, S.

2018-03-01

This study focuses on developing physics learning media using 3D cartoon on the static fluid topic. The purpose of this study is to describe: (1) the validity of the learning media, (2) the practicality of the learning media, and (3) the effectiveness of the learning media. This study is a research and development using ADDIE model. The subject of the implementation of media used class XI Science of SMAN 1 Pulau Laut Timur. The data were obtained from the validation sheet of the learning media, questionnaire, and the test of learning outcomes. The results showed that: (1) the validity of the media category is valid, (2) the practicality of the media category is practice, and (3) the effectiveness of the media category is effective. It is concluded that the learning using 3D cartoon on the static fluid topic is eligible to use in learning.

Nanoindentation cannot accurately predict the tensile strength of graphene or other 2D materials

NASA Astrophysics Data System (ADS)

Han, Jihoon; Pugno, Nicola M.; Ryu, Seunghwa

2015-09-01

Due to the difficulty of performing uniaxial tensile testing, the strengths of graphene and its grain boundaries have been measured in experiments by nanoindentation testing. From a series of molecular dynamics simulations, we find that the strength measured in uniaxial simulation and the strength estimated from the nanoindentation fracture force can differ significantly. Fracture in tensile loading occurs simultaneously with the onset of crack nucleation near 5-7 defects, while the graphene sheets often sustain the indentation loads after the crack initiation because the sharply concentrated stress near the tip does not give rise to enough driving force for further crack propagation. Due to the concentrated stress, strength estimation is sensitive to the indenter tip position along the grain boundaries. Also, it approaches the strength of pristine graphene if the tip is located slightly away from the grain boundary line. Our findings reveal the limitations of nanoindentation testing in quantifying the strength of graphene, and show that the loading-mode-specific failure mechanism must be taken into account in designing reliable devices from graphene and other technologically important 2D materials.Due to the difficulty of performing uniaxial tensile testing, the strengths of graphene and its grain boundaries have been measured in experiments by nanoindentation testing. From a series of molecular dynamics simulations, we find that the strength measured in uniaxial simulation and the strength estimated from the nanoindentation fracture force can differ significantly. Fracture in tensile loading occurs simultaneously with the onset of crack nucleation near 5-7 defects, while the graphene sheets often sustain the indentation loads after the crack initiation because the sharply concentrated stress near the tip does not give rise to enough driving force for further crack propagation. Due to the concentrated stress, strength estimation is sensitive to the indenter tip position along the grain boundaries. Also, it approaches the strength of pristine graphene if the tip is located slightly away from the grain boundary line. Our findings reveal the limitations of nanoindentation testing in quantifying the strength of graphene, and show that the loading-mode-specific failure mechanism must be taken into account in designing reliable devices from graphene and other technologically important 2D materials. Electronic ESI (ESI) available: Modelling of polycrystalline graphene, verification of loading speed, biaxial tensile simulations, comparison of stress distribution, size effects of indenter radius, force-deflection curves, and stability analysis of crack propagation. See DOI: 10.1039/c5nr04134a

Five secrets to leveraging maximum buying power with your media project.

PubMed

Hirsch, Lonnie

2010-11-01

Planning and executing a successful media campaign or project requires knowledge and expert execution of specific techniques and skills, including understanding of the requirements for proper media research and competitive intelligence, effective planning of media schedules, negotiation of best rates with media companies, monitoring the campaign, accurately tracking and evaluating results, and making smart adjustments based on tracking data to maximize the profitability and success of the enterprise. Some of the most important knowledge and techniques are not generally known by most advertisers, particularly small businesses like health care practices. This article reveals these tips that are the most effective and includes information on the use of experts and other professional resources that help increase the likelihood of a successful outcome for a well-planned and executed media campaign. Copyright © 2010 Elsevier Inc. All rights reserved.

Showcasing a profession: getting nursing on the newsstand.

PubMed

Hobdell, E F; Slusser, M; Patterson, J; Burgess, E

1991-01-01

Interacting with the media is a method of showcasing the nursing profession. Clinical nurse specialists (CNSs) have a variety of opportunities available for these interactions: appearing on television, participating in a radio program or writing to the media. A survey completed by the authors indicated that CNSs had many media interactions, yet overall, only 17% of all nurses surveyed used writing. This paper begins by discussing where to publish and how to prepare and target the audience. General and specific guidelines for publishing feature articles, health tips, letters to the editor, and other publishing possibilities are presented.

Circumnutation augmented in clinostatted plants by a tactile stimulus

NASA Technical Reports Server (NTRS)

Chapman, D. K.; Brown, A. H.

1981-01-01

Dark-grown, 4-day old, Helianthus annuus seedlings were rotated for 20 hr on horizontal clinostats to minimize the amplitude of circumnutation. Then a Plexiglas sheet was placed gently against the tip of the cotyledons. By time-lapse video imaging (using intermittent IR illumination to which the plants were insensitive) movements of the clinostatted plants were observed before, during, and after the period of mechanical contact. Immediately after the Plexiglas sheet was removed residual nutation increased in amplitude almost three-fold, then declined over the next 7 hr to the prestimulation level. This demonstration of enhancement of circumnutation by mechanical contact is consistent with the model of an endogeneous oscillator that can be stimulated by factors other than gravity.

The screw propeller

NASA Astrophysics Data System (ADS)

Larrabee, E. E.

1980-07-01

Marine and air screw propellers are considered in terms of theoretical hydrodynamics as developed by Joukowsky, Prandtl, and Betz. Attention is given to the flow around wings of finite span where spanwise flow exists and where lift and the bound vorticity must all go smoothly to zero at the wing tips. The concept of a trailing vortex sheet made up of infinitesimal line vortexes roughly aligned with the direction of flight is discussed in this regard. Also considered is induced velocity, which tends to convect the sheet downward at every stage in the roll-up process, the vortex theory of propellers and the Betz-Prandtl circulation distribution. The performance of the Gossamer Albatross and of a pedal-driven biplane called the Chrysalis are also discussed.

Neutrinos | News

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram Google+ YouTube Flickr

Computing | Home

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Quick Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter

Conformation-Directed Formation of Self-Healing Diblock Copolypeptide Hydrogels via Polyion Complexation.

PubMed

Sun, Yintao; Wollenberg, Alexander L; O'Shea, Timothy Mark; Cui, Yanxiang; Zhou, Z Hong; Sofroniew, Michael V; Deming, Timothy J

2017-10-25

Synthetic diblock copolypeptides were designed to incorporate oppositely charged ionic segments that form β-sheet-structured hydrogel assemblies via polyion complexation when mixed in aqueous media. The observed chain conformation directed assembly was found to be required for efficient hydrogel formation and provided distinct and useful properties to these hydrogels, including self-healing after deformation, microporous architecture, and stability against dilution in aqueous media. While many promising self-assembled materials have been prepared using disordered or liquid coacervate polyion complex (PIC) assemblies, the use of ordered chain conformations in PIC assemblies to direct formation of new supramolecular morphologies is unprecedented. The promising attributes and unique features of the β-sheet-structured PIC hydrogels described here highlight the potential of harnessing conformational order derived from PIC assembly to create new supramolecular materials.

Equivalent orthotropic elastic moduli identification method for laminated electrical steel sheets

NASA Astrophysics Data System (ADS)

Saito, Akira; Nishikawa, Yasunari; Yamasaki, Shintaro; Fujita, Kikuo; Kawamoto, Atsushi; Kuroishi, Masakatsu; Nakai, Hideo

2016-05-01

In this paper, a combined numerical-experimental methodology for the identification of elastic moduli of orthotropic media is presented. Special attention is given to the laminated electrical steel sheets, which are modeled as orthotropic media with nine independent engineering elastic moduli. The elastic moduli are determined specifically for use with finite element vibration analyses. We propose a three-step methodology based on a conventional nonlinear least squares fit between measured and computed natural frequencies. The methodology consists of: (1) successive augmentations of the objective function by increasing the number of modes, (2) initial condition updates, and (3) appropriate selection of the natural frequencies based on their sensitivities on the elastic moduli. Using the results of numerical experiments, it is shown that the proposed method achieves more accurate converged solution than a conventional approach. Finally, the proposed method is applied to measured natural frequencies and mode shapes of the laminated electrical steel sheets. It is shown that the method can successfully identify the orthotropic elastic moduli that can reproduce the measured natural frequencies and frequency response functions by using finite element analyses with a reasonable accuracy.

I Can Soar: How Technology Helps Students Take Off. A Resource Kit for Parents, Educators, and School Administrators Who Work with Students Who Have Disabilities.

ERIC Educational Resources Information Center

Gruner, Allison; Fleming, Erin; Bradley, Carl; Diamond, Christina M.; Ruedel, Kristin L. A.; Saunders, Jessica; Paulsen, Christine; McInerney, Maurice

This resource kit includes the following: Executive Summary; Legal Fact Sheet; Resource Guide; 26-minute "I Can Soar" Videotape; Video User's Guide; and Stories of Students Featured in Video. The materials provide tips to hep guide consumers in better integrating assistive technology (AT) within effective programs and services for children with…

Worldwide Emerging Environmental Issues Affecting the U.S. Military. December 2009 Report

DTIC Science & Technology

2009-12-01

serious loss of ice sheets and associated sea-level rise • Amazon rainforest ––increased weather-altering deforestation after passing a critical...scientists agree on some tipping elements that are extremely sensitive to climate shifts and therefore might have an important impact on the planetary...trigger radical changes Scientists point out that an additional important unknown element is the interaction of these and other known elements

Fingerprinting of music scores

NASA Astrophysics Data System (ADS)

Irons, Jonathan; Schmucker, Martin

2004-06-01

Publishers of sheet music are generally reluctant in distributing their content via the Internet. Although online sheet music distribution's advantages are numerous the potential risk of Intellectual Property Rights (IPR) infringement, e.g. illegal online distributions, disables any innovation propensity. While active protection techniques only deter external risk factors, additional technology is necessary to adequately treat further risk factors. For several media types including music scores watermarking technology has been developed, which ebeds information in data by suitable data modifications. Furthermore, fingerprinting or perceptual hasing methods have been developed and are being applied especially for audio. These methods allow the identification of content without prior modifications. In this article we motivate the development of watermarking and fingerprinting technologies for sheet music. Outgoing from potential limitations of watermarking methods we explain why fingerprinting methods are important for sheet music and address potential applications. Finally we introduce a condept for fingerprinting of sheet music.

Acceptability of a theory-based sedentary behaviour reduction intervention for older adults ('On Your Feet to Earn Your Seat').

PubMed

Matei, Raluca; Thuné-Boyle, Ingela; Hamer, Mark; Iliffe, Steve; Fox, Kenneth R; Jefferis, Barbara J; Gardner, Benjamin

2015-07-02

Adults aged 60 years and over spend most time sedentary and are the least physically active of all age groups. This early-phase study explored acceptability of a theory-based intervention to reduce sitting time and increase activity in older adults, as part of the intervention development process. An 8-week uncontrolled trial was run among two independent samples of UK adults aged 60-75 years. Sample 1, recruited from sheltered housing on the assumption that they were sedentary and insufficiently active, participated between December 2013 and March 2014. Sample 2, recruited through community and faith centres and a newsletter, on the basis of self-reported inactivity (<150 weekly minutes of moderate-to-vigorous activity) and sedentary behaviour (≥ 6 h mean daily sitting), participated between March and August 2014. Participants received a booklet offering 16 tips for displacing sitting with light-intensity activity and forming activity habits, and self-monitoring 'tick-sheets'. At baseline, 4-week, and 8-week follow-ups, quantitative measures were taken of physical activity, sedentary behaviour, and habit. At 8 weeks, tick-sheets were collected and a semi-structured interview conducted. Acceptability was assessed for each sample separately, through attrition and adherence to tips, ANOVAs for behaviour and habit changes, and, for both samples combined, thematic analysis of interviews. In Sample 1, 12 of 16 intervention recipients completed the study (25% attrition), mean adherence was 40% (per-tip range: 15-61%), and there were no clear patterns of changes in sedentary or physical activity behaviour or habit. In Sample 2, 23 of 27 intervention recipients completed (15% attrition), and mean adherence was 58% (per-tip range: 39-82%). Sample 2 decreased mean sitting time and sitting habit, and increased walking, moderate activity, and activity habit. Qualitative data indicated that both samples viewed the intervention positively, found the tips easy to follow, and reported health and wellbeing gains. Low attrition, moderate adherence, and favourability in both samples, and positive changes in Sample 2, indicate the intervention was acceptable. Higher attrition, lower adherence, and no apparent behavioural impact among Sample 1 could perhaps be attributable to seasonal influences. The intervention has been refined to address emergent acceptability problems. An exploratory controlled trial is underway.

Sustainability

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For

Phenomenological Model of Current Sheet Canting in Pulsed Electromagnetic Accelerators

NASA Technical Reports Server (NTRS)

Markusic, Thomas; Choueiri, E. Y.

2003-01-01

The phenomenon of current sheet canting in pulsed electromagnetic accelerators is the departure of the plasma sheet (that carries the current) from a plane that is perpendicular to the electrodes to one that is skewed, or tipped. Review of pulsed electromagnetic accelerator literature reveals that current sheet canting is a ubiquitous phenomenon - occurring in all of the standard accelerator geometries. Developing an understanding of current sheet canting is important because it can detract from the propellant sweeping capabilities of current sheets and, hence, negatively impact the overall efficiency of pulsed electromagnetic accelerators. In the present study, it is postulated that depletion of plasma near the anode, which results from axial density gradient induced diamagnetic drift, occurs during the early stages of the discharge, creating a density gradient normal to the anode, with a characteristic length on the order of the ion skin depth. Rapid penetration of the magnetic field through this region ensues, due to the Hall effect, leading to a canted current front ahead of the initial current conduction channel. In this model, once the current sheet reaches appreciable speeds, entrainment of stationary propellant replenishes plasma in the anode region, inhibiting further Hall-convective transport of the magnetic field; however, the previously established tilted current sheet remains at a fairly constant canting angle for the remainder of the discharge cycle, exerting a transverse J x B force which drives plasma toward the cathode and accumulates it there. This proposed sequence of events has been incorporated into a phenomenological model. The model predicts that canting can be reduced by using low atomic mass propellants with high propellant loading number density; the model results are shown to give qualitative agreement with experimentally measured canting angle mass dependence trends.

Evolution of music score watermarking algorithm

NASA Astrophysics Data System (ADS)

Busch, Christoph; Nesi, Paolo; Schmucker, Martin; Spinu, Marius B.

2002-04-01

Content protection for multimedia data is widely recognized especially for data types that are frequently distributed, sold or shared using the Internet. Particularly music industry dealing with audio files realized the necessity for content protection. Distribution of music sheets will face the same problems. Digital watermarking techniques provide a certain level of protection for these music sheets. But classical raster-oriented watermarking algorithms for images suffer several drawbacks when directly applied to image representations of music sheets. Therefore new solutions have been developed which are designed regarding the content of the music sheets. In Comparison to other media types the development for watermarking of music scores is a rather young art. The paper reviews the evolution of the early approaches and describes the current state of the art in the field.

Possible participation of transient sheets of 1. -->. 4-. beta. -glucans in the biosynthesis of cellulose I. [Acetobacter xylinum

DOE Office of Scientific and Technical Information (OSTI.GOV)

Colvin, J.R.

1983-01-01

It is suggested that a primary, essential stage in the biologic formation of a microfibril of cellulose I is an extracellular, lateral association of presynthesized (1..-->..4)-..beta..-D-glucans, by hydrogen bonding, to form long, thin sheets. These sheets then superimpose themselves nonenzymatically by London forces to form the nascent microfibril. The ends of the constituent glucans of the nascent microfibril may undergo extension or rearrangement of the type indicated by Maclachlan and colleagues. The formation of the metastable, native structure (cellulose I) may be deduced from the above suggestion as a natural consequence of closest packing of the sheets. The irreversibility ofmore » the change from cellulose I to cellulose II, either by mercerization or regeneration, also follows from the postulate. The suggestion also explains why cellulose microfibrils and chitin microfibrils may be formed contiguously in cell walls without interfering with each other. High-resolution electron micrographs of the tips of newly formed microfibrils of bacterial cellulose which had been very lightly negatively stained with sodium phosphotungstate are consistent with the suggestion. 33 references, 3 figures.« less

Variability of AVHRR-Derived Clear-Sky Surface Temperature over the Greenland Ice Sheet.

NASA Astrophysics Data System (ADS)

Stroeve, Julienne; Steffen, Konrad

1998-01-01

The Advanced Very High Resolution Radiometer is used to derive surface temperatures for one satellite pass under clear skies over the Greenland ice sheet from 1989 through 1993. The results of these temperatures are presented as monthly means, and their spatial and temporal variability are discussed. Accuracy of the dry snow surface temperatures is estimated to be better than 1 K during summer. This error is expected to increase during polar night due to problems in cloud identification. Results indicate the surface temperature of the Greenland ice sheet is strongly dominated by topography, with minimum surface temperatures associated with the high elevation regions. In the summer, maximum surface temperatures occur during July along the western coast and southern tip of the ice sheet. Minimum temperatures are found at the summit during summer and move farther north during polar night. Large interannual variability in surface temperatures occurs during winter associated with katabatic storm events. Summer temperatures show little variation, although 1992 stands out as being colder than the other years. The reason for the lower temperatures during 1992 is believed to be a result of the 1991 eruption of Mount Pinatubo.

CROMERR Program Fact Sheet

EPA Pesticide Factsheets

The Cross-Media Electronic Reporting Rule (CROMERR), published in the Federal Register under 40 CFR, Part 3 on October 13, 2005, provides the legal framework for electronic reporting under all of EPA's environmental regulations.

ANNIE | News

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media , Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact

Coupling frontal elution paper chromatography with desorption corona beam ionization mass spectrometry for rapid analysis of chlorphenamine in herbal medicines and dietary supplements.

PubMed

Huang, Yun-Qing; You, Jing-Qing; Zhang, Junsheng; Sun, Wenjian; Ding, Li; Feng, Yu-Qi

2011-10-14

We developed a convenient method by coupling frontal elution paper chromatography with desorption corona beam ionization mass spectrometry (DCBI-MS) for rapid determination of chlorphenamine added in herbal medicines or dietary supplements. In this method, the ethanol extract of the herbal products was spotted directly onto an isosceles triangular filter paper sheet, and then the paper sheet was developed under strong elution condition with the sample zone migrating at the solvent front. The analyte was finally condensed at the V-shaped tip which could then be placed under the visible plasma beam of DCBI for ionization. The overall procedure took less than 5 min. The frontal elution paper chromatography on a triangular plate used in this work improved the signal intensity of chlorphenamine by 30-fold due to the analyte condensing at the tip and the reduction of the background suppression. Furthermore, the paper sheet also functioned as a filter in the analysis of solid or powder samples, which can increase the analytical throughput by omitting the step of centrifugation. The proposed method in current study was successfully applied in the determination of chlorphenamine in herbal medicines. Chlorphenamine was detected in four of the twelve types of herbal medicines examined in this study. The limit of detection was 200 ng/mL (2.0 ng absolute) in full-scan positive-ion mode and the linear range was from 5.0 μg/mL to 50 μg/mL with satisfactory linear coefficient (R(2) (the square of the correlation coefficient)=0.895). Good reproducibility was achieved with relative standard deviations (RSDs) less than 15.0% and the recoveries of chlorphenamine ranged from 84.3 to 90.6%. Copyright © 2011 Elsevier B.V. All rights reserved.

From Aβ Filament to Fibril: Molecular Mechanism of Surface-Activated Secondary Nucleation from All-Atom MD Simulations.

PubMed

Schwierz, Nadine; Frost, Christina V; Geissler, Phillip L; Zacharias, Martin

2017-02-02

Secondary nucleation pathways in which existing amyloid fibrils catalyze the formation of new aggregates and neurotoxic oligomers are of immediate importance for the onset and progression of Alzheimer's disease. Here, we apply extensive all-atom molecular dynamics simulations in explicit water to study surface-activated secondary nucleation pathways at the extended lateral β-sheet surface of a preformed Aβ 9-40 filament. Calculation of free-energy profiles allows us to determine binding free energies and conformational intermediates for nucleation complexes consisting of 1-4 Aβ peptides. In addition, we combine the free-energy profiles with position-dependent diffusion profiles to extract complementary kinetic information and macroscopic growth rates. Single monomers bind to the β-sheet surface in a disordered, hydrophobically collapsed conformation, whereas dimers and larger oligomers can retain a cross-β conformation resembling a more ordered fibril structure. The association processes during secondary nucleation follow a dock/lock mechanism consisting of a fast initial encounter phase (docking) and a slow structural rearrangement phase (locking). The major driving forces for surface-activated secondary nucleation are the release of a large number of hydration water molecules and the formation of hydrophobic interface contacts, the latter being in contrast to the elongation process at filament tips, which is dominated by the formation of stable and highly specific interface hydrogen bonds. The calculated binding free energies and the association rates for the attachment of Aβ monomers and oligomers to the extended lateral β-sheet surface of the filament seed are higher compared to those for elongation at the filament tips, indicating that secondary nucleation pathways can become important once a critical concentration of filaments has formed.

A Hand-held Fiber-optic Implement for the Site-specific Delivery of Photosensitizer and Singlet Oxygen

PubMed Central

Mahendran, Adaickapillai; Kopkalli, Yasemin; Ghosh, Goutam; Ghogare, Ashwini; Minnis, Mihaela; Kruft, Bonnie I.; Zamadar, Matibur; Aebisher, David; Davenport, Lesley; Greer, Alexander

2012-01-01

We have constructed a fiber optic device that internally flows triplet oxygen and externally produces singlet oxygen, causing a reaction at the (Z)-1,2-dialkoxyethene spacer group, freeing a pheophorbide sensitizer upon the fragmentation of a reactive dioxetane intermediate. The device can be operated and sensitizer photorelease observed using absorption and fluorescence spectroscopy. We demonstrate the preference of sensitizer photorelease when the probe tip is in contact with octanol or lipophilic media. A first-order photocleavage rate constant of 1.13 h−1 was measured in octanol where dye desorption was not accompanied by readsorption. When the probe tip contacts aqueous solution, the photorelease was inefficient because most of the dye adsorbed on the probe tip, even after the covalent ethene spacer bonds have been broken. The observed stability of the free sensitizer in lipophilic media is reasonable even though it is a pyropheophorbide-a derivative that carries a p-formylbenzylic alcohol substituent at the carboxylic acid group. In octanol or lipid systems, we found that the dye was not susceptible to hydrolysis to pyropheophorbide-a, otherwise a pH effect was observed in a binary methanol-water system (9:1) at pH below 2 or above 8. PMID:21790616

Recall and Believability of the Tips From Former Smokers Campaign Among University Students

PubMed Central

Ickes, Melinda. J.; Butler, Karen; Rayens, Mary Kay; Noland, Melody; Wiggins, Amanda T.; Hahn, Ellen J.

2016-01-01

Background Tobacco media campaigns are effective, but less is known regarding the impact on college students. Purpose The purpose was to test the effects of an on-campus Tips television campaign on frequency and believability of ads recalled and to assess demographic and personal factors associated with believability. Methods A quasi-experimental pre-post design was used to assess the 8-week campaign with three Tips ads. Two randomly-selected cohorts of college students (N = 1,593) from a large public university completed online surveys pre- and post-campaign. Group comparisons using chi-square tests, two-sample t-tests, and logistic regression, controlling for residence or cohort; predictors of believability using proportional odds modeling. Results Ads were recalled by significantly more students (68%) post-campaign. Believability for one or more ads was lower for males, undergraduates, those belonging to fraternity/sorority, and current polytobacco users (p<.05). Believability was greater for those who recalled seeing the ads more often (p<.05). Discussion Sub-groups of college students, including males and undergraduates, reported less ad believability, which should be considered when designing communication strategies. Translation to Health Education Practice Considering the potential impact and cost-effective nature of on-campus TV media campaigns, these ads need to be integrated into current campus tobacco control strategies. PMID:28396713

Recall and Believability of the Tips From Former Smokers Campaign Among University Students.

PubMed

Ickes, Melinda J; Butler, Karen; Rayens, Mary Kay; Noland, Melody; Wiggins, Amanda T; Hahn, Ellen J

2016-01-01

Tobacco media campaigns are effective, but less is known regarding the impact on college students. The purpose was to test the effects of an on-campus Tips television campaign on frequency and believability of ads recalled and to assess demographic and personal factors associated with believability. A quasi-experimental pre-post design was used to assess the 8-week campaign with three Tips ads. Two randomly-selected cohorts of college students ( N = 1,593) from a large public university completed online surveys pre- and post-campaign. Group comparisons using chi-square tests, two-sample t-tests, and logistic regression, controlling for residence or cohort; predictors of believability using proportional odds modeling. Ads were recalled by significantly more students (68%) post-campaign. Believability for one or more ads was lower for males, undergraduates, those belonging to fraternity/sorority, and current polytobacco users ( p <.05). Believability was greater for those who recalled seeing the ads more often ( p <.05). Sub-groups of college students, including males and undergraduates, reported less ad believability, which should be considered when designing communication strategies. Considering the potential impact and cost-effective nature of on-campus TV media campaigns, these ads need to be integrated into current campus tobacco control strategies.

A Primer on Social Media for Plastic Surgeons: What Do I Need to Know About Social Media and How Can It Help My Practice?

PubMed

Gould, Daniel J; Grant Stevens, W; Nazarian, Sheila

2017-05-01

Social media has changed the way plastic surgeons interact with their colleagues, patients, and friends. Social media is a rapidly changing phenomenon that it is critical to plastic surgeons and their practice. Plastic surgery can be marketed directly to consumers and therefore social media can provide a valuable platform to interact with potential patients and to define a surgeon's expertise and practice online. Social media impacts search engine optimization algorithms, increasing web traffic to a surgeon's site, and it can affect patients' perceptions of the practice and surgeon. Social media is a powerful tool, but it should be harnessed wisely to avoid potential pitfalls. This article provides an overview of social media, an outline of resources for surgeons to use, and some tips and tricks for new users. © 2017 The American Society for Aesthetic Plastic Surgery, Inc. Reprints and permission: journals.permissions@oup.com.

Are you Scared Yet?: Evaluating Fear Appeal Messages in Tweets about the Tips Campaign.

PubMed

Emery, Sherry L; Szczypka, Glen; Abril, Eulàlia Puig; Kim, Yoonsang; Vera, Lisa

2014-04-01

In March 2012, the CDC launched "Tips from Former Smokers," a $54 million national campaign featuring individuals experiencing long-term health consequences of smoking. The campaign approach was based on strong evidence that anti-tobacco ads portraying fear, graphic images, and personal testimonials are associated with attitudinal and behavior change. Yet it was also controversial; critics cited the danger that viewers might reject such intensely graphic messages. Tasked with informing this debate, our study analyzes the corpus of Tips campaign-related tweets obtained via the Twitter Firehose. We provide a novel and rigorous method for media campaign evaluation within the framework of the Extended Parallel Process Model. Among the relevant Tweets, 87% showed evidence of message acceptance, while 7% exhibited message rejection.

Face Sheet/Core Disbond Growth in Honeycomb Sandwich Panels Subjected to Ground-Air-Ground Pressurization and In-Plane Loading

NASA Technical Reports Server (NTRS)

Chen, Zhi M.; Krueger, Ronald; Rinker, Martin

2015-01-01

Typical damage modes in light honeycomb sandwich structures include face sheet/core disbonding and core fracture, both of which can pose a threat to the structural integrity of a component. These damage modes are of particular interest to aviation certification authorities since several in-service occurrences, such as rudder structural failure and other control surface malfunctions, have been attributed to face sheet/core disbonding. Extensive studies have shown that face sheet/core disbonding and core fracture can lead to damage propagation caused by internal pressure changes in the core. The increasing use of composite sandwich construction in aircraft applications makes it vitally important to understand the effect of ground-air-ground (GAG) cycles and conditions such as maneuver and gust loads on face sheet/core disbonding. The objective of the present study was to use a fracture mechanics based approach developed earlier to evaluate the loading at the disbond front caused by ground-air-ground pressurization and in-plane loading. A honeycomb sandwich panel containing a circular disbond at one face sheet/core interface was modeled with three-dimensional (3D) solid finite elements. The disbond was modeled as a discrete discontinuity and the strain energy release rate along the disbond front was computed using the Virtual Crack Closure Technique (VCCT). Special attention was paid to the pressure-deformation coupling which can decrease the pressure load within the disbonded sandwich section significantly when the structure is highly deformed. The commercial finite element analysis software, Abaqus/Standard, was used for the analyses. The recursive pressure-deformation coupling problem was solved by representing the entrapped air in the honeycomb cells as filled cavities in Abaqus/Standard. The results show that disbond size, face sheet thickness and core thickness are important parameters that determine crack tip loading at the disbond front. Further, the pressure-deformation coupling was found to have an important load decreasing effect [6]. In this paper, a detailed problem description is provided first. Second, the analysis methodology is presented. The fracture mechanics approach used is described and the specifics of the finite element model, including the fluid-filled cavities, are introduced. Third, the initial model verification and validation are discussed. Fourth, the findings from a closely related earlier study [6] are summarized. These findings provided the basis for the current investigation. Fifth, an aircraft ascent scenario from 0 to 12192 m (0 to 40000 ft) is considered and the resulting crack tip loading at the disbond front is determined. In-plane loading to simulate maneuvers and gust conditions are also considered. Sixth, the results are shown for a curved panel, which was used to simulate potential fuselage applications. Finally, a brief summary of observations is presented and recommendations for improvement are provided.

Hygiene Etiquette: Coughing and Sneezing

MedlinePlus

... Statistics Health Promotion Materials Campaigns Fact Sheets Podcasts Posters Presentations Social Media Stickers Videos/TV Newsroom, Features, ... on Facebook Tweet Share Compartir This vintage British poster from World War II shows that coughing and ...

Fermilab | About | Organization | Fermilab Organization

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram Google+ YouTube Flickr

Analysis of the sweeped actuator line method

DOE PAGES

Nathan, Jörn; Masson, Christian; Dufresne, Louis; ...

2015-10-16

The actuator line method made it possible to describe the near wake of a wind turbine more accurately than with the actuator disk method. Whereas the actuator line generates the helicoidal vortex system shed from the tip blades, the actuator disk method sheds a vortex sheet from the edge of the rotor plane. But with the actuator line come also temporal and spatial constraints, such as the need for a much smaller time step than with actuator disk. While the latter one only has to obey the Courant-Friedrichs-Lewy condition, the former one is also restricted by the grid resolution andmore » the rotor tip-speed. Additionally the spatial resolution has to be finer for the actuator line than with the actuator disk, for well resolving the tip vortices. Therefore this work is dedicated to examining a method in between of actuator line and actuator disk, which is able to model the transient behavior, such as the rotating blades, but which also relaxes the temporal constraint. Therefore a larger time-step is used and the blade forces are swept over a certain area. As a result, the main focus of this article is on the aspect of the blade tip vortex generation in comparison with the standard actuator line and actuator disk.« less

Analysis of the sweeped actuator line method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nathan, Jörn; Masson, Christian; Dufresne, Louis

The actuator line method made it possible to describe the near wake of a wind turbine more accurately than with the actuator disk method. Whereas the actuator line generates the helicoidal vortex system shed from the tip blades, the actuator disk method sheds a vortex sheet from the edge of the rotor plane. But with the actuator line come also temporal and spatial constraints, such as the need for a much smaller time step than with actuator disk. While the latter one only has to obey the Courant-Friedrichs-Lewy condition, the former one is also restricted by the grid resolution andmore » the rotor tip-speed. Additionally the spatial resolution has to be finer for the actuator line than with the actuator disk, for well resolving the tip vortices. Therefore this work is dedicated to examining a method in between of actuator line and actuator disk, which is able to model the transient behavior, such as the rotating blades, but which also relaxes the temporal constraint. Therefore a larger time-step is used and the blade forces are swept over a certain area. As a result, the main focus of this article is on the aspect of the blade tip vortex generation in comparison with the standard actuator line and actuator disk.« less

Ten Tips To Aid Teachers Creating Multimedia Presentations.

ERIC Educational Resources Information Center

Ennis, Willie; Ennis, Demetria

1996-01-01

Suggestions to help teachers create original multimedia presentations and lessons include building resource teams, knowing intellectual property and copyright issues, analyzing target audiences, carefully selecting media, considering hardware and software requirements, seeking technical support, encouraging distribution on the World Wide Web,…

Teaching Tips.

ERIC Educational Resources Information Center

Journalism Educator, 1985

1985-01-01

Presents a variety of journalism classroom techniques, including an editing scavenger hunt, a discovery method for compiling news sources, intense instruction in news technology, criteria for evaluating ad copy, a course combining print and broadcast journalism, use of the Teletext, and teaching ad forms for the new media. (HTH)

Contact the Office of Communication | News

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram

Facilities Engineering Services Section

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For

Internal Audit Service | Internal Audit Service

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Home Contact Phone Book Fermilab at Work For Industry Jobs Interact Facebook Twitter Instagram Google

Tractor/Lawn Mower | News

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Science Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For

Development of Chemistry Game Card as an Instructional Media in the Subject of Naming Chemical Compound in Grade X

NASA Astrophysics Data System (ADS)

Bayharti; Iswendi, I.; Arifin, M. N.

2018-04-01

The purpose of this research was to produce a chemistry game card as an instructional media in the subject of naming chemical compounds and determine the degree of validity and practicality of instructional media produced. Type of this research was Research and Development (R&D) that produced a product. The development model used was4-D model which comprises four stages incuding: (1) define, (2) design, (3) develop, and (4) disseminate. This research was restricted at the development stage. Chemistry game card developed was validated by seven validators and practicality was tested to class X6 students of SMAN 5 Padang. Instrument of this research is questionnair that consist of validity sheet and practicality sheet. Technique in collection data was done by distributing questionnaire to the validators, chemistry teachers, and students. The data were analyzed by using formula Cohen’s Kappa. Based on data analysis, validity of chemistry game card was0.87 with category highly valid and practicality of chemistry game card was 0.91 with category highly practice.

Does Digital Ad Exposure Influence Information-Seeking Behavior Online? Evidence From the 2012 Tips From Former Smokers National Tobacco Prevention Campaign

PubMed Central

Hansen, Heather; Duke, Jennifer; Davis, Kevin; Alexander, Robert; Rowland, Amy; Mitchko, Jane

2016-01-01

Background Measuring the impact of online health campaigns is challenging. Ad click-through rates are traditionally used to measure campaign reach, but few Internet users ever click on ads. Alternatively, self-reported exposure to digital ads would be prone to recall bias. Furthermore, there may be latency effects whereby people do not click on ads when exposed but visit the promoted website or conduct campaign-related searches later. Online panels that unobtrusively collect panelists’ Web behavior data and link ad exposure to website visits and searches can more reliably assess the impact of digital ad exposure. From March to June 2012, the Centers for Disease Control and Prevention aired the national Tips From Former Smokers (Tips 2012) media campaign designed to encourage current smokers to quit. Advertisements ran across media channels, and the digital ads directed users to the Tips 2012 campaign website. Objective Our aim was to examine whether exposure to Tips 2012 digital ads influenced information-seeking behaviors online. Methods ComScore mined its panelists’ Web behavior data for unique codes that would indicate exposure to Tips 2012 ads, regardless of whether panelists clicked the ad or not. A total of 15,319 US adults were identified as having been exposed to a Tips 2012 campaign ad. An equal number of unexposed adults (N=15,319) were identified and matched on demographics and Internet use behavior to the exposed group. Panelists’ Web behavior data were mined for up to 4 weeks after initial Tips 2012 ad exposure to determine whether they visited the Tips 2012 campaign website or other cessation-related websites (eg, nicotine replacement therapy site) or conducted searches for campaign-related topics (eg, quit smoking). Results The proportion of exposed adults visiting the Tips 2012 sites increased from 0.4% in Week 1 to 0.9% 4 weeks after ad exposure, and these rates were significantly higher than in the unexposed group (0.1% in Week 1 to 0.4% in Week 4, P<.001) across all weeks examined. The proportion of exposed panelists visiting other cessation websites increased from 0.2% in Week 1 to 0.3% 4 weeks after initial ad exposure, and these rates were significantly higher than in the unexposed group (0.0% in Week 1 to 0.2% in Week 4, P=.001 to P=.019) across all weeks examined. There were no significant differences in searches for campaign-related topics between the exposed and unexposed group during most of the weeks examined. Conclusions These results suggest that online ad exposure is associated with confirmed visits to the Tips 2012 campaign sites and visits to other cessation websites and that these information-seeking behaviors occur up to several weeks after ad exposure. Web behavior data from online panels are useful for examining exposure and behavioral responses to digital campaign ads. PMID:26983849

Does Digital Ad Exposure Influence Information-Seeking Behavior Online? Evidence From the 2012 Tips From Former Smokers National Tobacco Prevention Campaign.

PubMed

Kim, Annice; Hansen, Heather; Duke, Jennifer; Davis, Kevin; Alexander, Robert; Rowland, Amy; Mitchko, Jane

2016-03-16

Measuring the impact of online health campaigns is challenging. Ad click-through rates are traditionally used to measure campaign reach, but few Internet users ever click on ads. Alternatively, self-reported exposure to digital ads would be prone to recall bias. Furthermore, there may be latency effects whereby people do not click on ads when exposed but visit the promoted website or conduct campaign-related searches later. Online panels that unobtrusively collect panelists' Web behavior data and link ad exposure to website visits and searches can more reliably assess the impact of digital ad exposure. From March to June 2012, the Centers for Disease Control and Prevention aired the national Tips From Former Smokers (Tips 2012) media campaign designed to encourage current smokers to quit. Advertisements ran across media channels, and the digital ads directed users to the Tips 2012 campaign website. Our aim was to examine whether exposure to Tips 2012 digital ads influenced information-seeking behaviors online. ComScore mined its panelists' Web behavior data for unique codes that would indicate exposure to Tips 2012 ads, regardless of whether panelists clicked the ad or not. A total of 15,319 US adults were identified as having been exposed to a Tips 2012 campaign ad. An equal number of unexposed adults (N=15,319) were identified and matched on demographics and Internet use behavior to the exposed group. Panelists' Web behavior data were mined for up to 4 weeks after initial Tips 2012 ad exposure to determine whether they visited the Tips 2012 campaign website or other cessation-related websites (eg, nicotine replacement therapy site) or conducted searches for campaign-related topics (eg, quit smoking). The proportion of exposed adults visiting the Tips 2012 sites increased from 0.4% in Week 1 to 0.9% 4 weeks after ad exposure, and these rates were significantly higher than in the unexposed group (0.1% in Week 1 to 0.4% in Week 4, P<.001) across all weeks examined. The proportion of exposed panelists visiting other cessation websites increased from 0.2% in Week 1 to 0.3% 4 weeks after initial ad exposure, and these rates were significantly higher than in the unexposed group (0.0% in Week 1 to 0.2% in Week 4, P=.001 to P=.019) across all weeks examined. There were no significant differences in searches for campaign-related topics between the exposed and unexposed group during most of the weeks examined. These results suggest that online ad exposure is associated with confirmed visits to the Tips 2012 campaign sites and visits to other cessation websites and that these information-seeking behaviors occur up to several weeks after ad exposure. Web behavior data from online panels are useful for examining exposure and behavioral responses to digital campaign ads.

APPLICATION OF STEEL PIPE PILE LOADING TESTS TO DESIGN VERIFICATION OF FOUNDATION OF THE TOKYO GATE BRIDGE

NASA Astrophysics Data System (ADS)

Saitou, Yutaka; Kikuchi, Yoshiaki; Kusakabe, Osamu; Kiyomiya, Osamu; Yoneyama, Haruo; Kawakami, Taiji

Steel sheet pipe pile foundations with large diameter steel pipe sheet pile were used for the foundation of the main pier of the Tokyo Gateway bridge. However, as for the large diameter steel pipe pile, the bearing mechanism including a pile tip plugging effect is still unclear due to lack of the practical examinations even though loading tests are performed on Trans-Tokyo Bay Highway. In the light of the foregoing problems, static pile loading tests both vertical and horizontal directions, a dynamic loading test, and cone penetration tests we re conducted for determining proper design parameters of the ground for the foundations. Design parameters were determined rationally based on the tests results. Rational design verification was obtained from this research.

Fatigue crack growth in 2024-T3 aluminum under tensile and transverse shear stresses

NASA Technical Reports Server (NTRS)

Viz, Mark J.; Zehnder, Alan T.

1994-01-01

The influence of transverse shear stresses on the fatigue crack growth rate in thin 2024-T3 aluminum alloy sheets is investigated experimentally. The tests are performed on double-edge cracked sheets in cyclic tensile and torsional loading. This loading generates crack tip stress intensity factors in the same ratio as the values computed for a crack lying along a lap joint in a pressurized aircraft fuselage. The relevant fracture mechanics of cracks in thin plates along with the details of the geometrically nonlinear finite element analyses used for the test specimen calibration are developed and discussed. Preliminary fatigue crack growth data correlated using the fully coupled stress intensity factor calibration are presented and compared with fatigue crack growth data from pure delta K(sub I)fatigue tests.

Path Dependence of Regional Climate Change

NASA Astrophysics Data System (ADS)

Herrington, Tyler; Zickfeld, Kirsten

2013-04-01

Path dependence of the climate response to CO2 forcing has been investigated from a global mean perspective, with evidence suggesting that long-term global mean temperature and precipitation changes are proportional to cumulative CO2 emissions, and independent of emissions pathway. Little research, however, has been done on path dependence of regional climate changes, particularly in areas that could be affected by tipping points. Here, we utilize the UVic Earth System Climate Model version 2.9, an Earth System Model of Intermediate Complexity. It consists of a 3-dimensional ocean general circulation model, coupled with a dynamic-thermodynamic sea ice model, and a thermodynamic energy-moisture balance model of the atmosphere. This is then coupled with a terrestrial carbon cycle model and an ocean carbon-cycle model containing an inorganic carbon and marine ecosystem component. Model coverage is global with a zonal resolution of 3.6 degrees and meridional resolution of 1.8 degrees. The model is forced with idealized emissions scenarios across five cumulative emission groups (1300 GtC, 2300 GtC, 3300 GtC, 4300 GtC, and 5300 GtC) to explore the path dependence of (and the possibility of hysteresis in) regional climate changes. Emission curves include both fossil carbon emissions and emissions from land use changes, and span a variety of peak and decline scenarios with varying emission rates, as well as overshoot and instantaneous pulse scenarios. Tipping points being explored include those responsible for the disappearance of summer Arctic sea-ice, the irreversible melt of the Greenland Ice Sheet, the collapse of the Atlantic Thermohaline Circulation, and the dieback of the Amazonian Rainforest. Preliminary results suggest that global mean climate change after cessation of CO2 emissions is independent of the emissions pathway, only varying with total cumulative emissions, in accordance with results from earlier studies. Forthcoming analysis will investigate path dependence of regional climate change. Some evidence exists to support the idea of hysteresis in the Greenland Ice Sheet, and since tipping points represent non-linear elements of the climate system, we suspect that the other tipping points might also show path dependence.

Investigation of Unsteady Flow Field in a Low-Speed One and a Half Stage Axial Compressor. Part 2; Effects of Tip Gap Size On the Tip Clearance Flow Structure at Near Stall Operation

NASA Technical Reports Server (NTRS)

Hah, Chunill; Hathaway, Michael; Katz, Joseph

2014-01-01

The primary focus of this paper is to investigate the effect of rotor tip gap size on how the rotor unsteady tip clearance flow structure changes in a low speed one and half stage axial compressor at near stall operation (for example, where maximum pressure rise is obtained). A Large Eddy Simulation (LES) is applied to calculate the unsteady flow field at this flow condition with both a small and a large tip gaps. The numerically obtained flow fields at the small clearance matches fairly well with the available initial measurements obtained at the Johns Hopkins University with 3-D unsteady PIV in an index-matched test facility which renders the compressor blades and casing optically transparent. With this setup, the unsteady velocity field in the entire flow domain, including the flow inside the tip gap, can be measured. The numerical results are also compared with previously published measurements in a low speed single stage compressor (Maerz et al. [2002]). The current study shows that, with the smaller rotor tip gap, the tip clearance vortex moves to the leading edge plane at near stall operating condition, creating a nearly circumferentially aligned vortex that persists around the entire rotor. On the other hand, with a large tip gap, the clearance vortex stays inside the blade passage at near stall operation. With the large tip gap, flow instability and related large pressure fluctuation at the leading edge are observed in this one and a half stage compressor. Detailed examination of the unsteady flow structure in this compressor stage reveals that the flow instability is due to shed vortices near the leading edge, and not due to a three-dimensional separation vortex originating from the suction side of the blade, which is commonly referred to during a spike-type stall inception. The entire tip clearance flow is highly unsteady. Many vortex structures in the tip clearance flow, including the sheet vortex system near the casing, interact with each other. The core tip clearance vortex, which is formed with the rotor tip gap flows near the leading edge, is also highly unsteady or intermittent due to pressure oscillations near the leading edge and varies from passage to passage. For the current compressor stage, the evidence does not seem to support that a classical vortex breakup occurs in any organized way, even with the large tip gap. Although wakes from the IGV influence the tip clearance flow in the rotor, the major characteristics of rotor tip clearance flows in isolated or single stage rotors are observed in this one and a half stage axial compressor.

Comparison between the Amount of Environmental Change and the Amount of Transcriptome Change

PubMed Central

Ogata, Norichika; Kozaki, Toshinori; Yokoyama, Takeshi; Hata, Tamako; Iwabuchi, Kikuo

2015-01-01

Cells must coordinate adjustments in genome expression to accommodate changes in their environment. We hypothesized that the amount of transcriptome change is proportional to the amount of environmental change. To capture the effects of environmental changes on the transcriptome, we compared transcriptome diversities (defined as the Shannon entropy of frequency distribution) of silkworm fat-body tissues cultured with several concentrations of phenobarbital. Although there was no proportional relationship, we did identify a drug concentration “tipping point” between 0.25 and 1.0 mM. Cells cultured in media containing lower drug concentrations than the tipping point showed uniformly high transcriptome diversities, while those cultured at higher drug concentrations than the tipping point showed uniformly low transcriptome diversities. The plasticity of transcriptome diversity was corroborated by cultivations of fat bodies in MGM-450 insect medium without phenobarbital and in 0.25 mM phenobarbital-supplemented MGM-450 insect medium after previous cultivation (cultivation for 80 hours in MGM-450 insect medium without phenobarbital, followed by cultivation for 10 hours in 1.0 mM phenobarbital-supplemented MGM-450 insect medium). Interestingly, the transcriptome diversities of cells cultured in media containing 0.25 mM phenobarbital after previous cultivation (cultivation for 80 hours in MGM-450 insect medium without phenobarbital, followed by cultivation for 10 hours in 1.0 mM phenobarbital-supplemented MGM-450 insect medium) were different from cells cultured in media containing 0.25 mM phenobarbital after previous cultivation (cultivation for 80 hours in MGM-450 insect medium without phenobarbital). This hysteretic phenomenon of transcriptome diversities indicates multi-stability of the genome expression system. Cellular memories were recorded in genome expression networks as in DNA/histone modifications. PMID:26657512

Patient Satisfaction After Rhinoplasty: A Social Media Analysis.

PubMed

Khansa, Ibrahim; Khansa, Lara; Pearson, Gregory D

2016-01-01

Compared to other cosmetic procedures, rhinoplasty has a relatively low patient satisfaction rate, due to the difficulty of the procedure, and potentially unrealistic patient expectations. Understanding the reasons behind patient dissatisfaction is key to improving outcomes. Previous authors have done surgeon-initiated surveys, expert ratings, and morphologic measurements, to measure rhinoplasty success. No study has analyzed online reviews by patients to identify reasons for dissatisfaction with rhinoplasty. The goal of this study was to analyze satisfaction patterns in rhinoplasty using online reviews. All primary rhinoplasty reviews on RealSelf (Seattle, WA), a social media website for patients undergoing cosmetic surgery, were reviewed. The researchers recorded patient gender, whether they were satisfied, and the reasons for satisfaction or dissatisfaction. Male and female patients were compared, using chi-squared analysis. There were 2326 reviews for primary rhinoplasty (2032 females, 294 males). The overall satisfaction rate was 83.6%. Significantly more females than males were satisfied (87.6% vs 56.1%, P < .001). Among males, the most common reasons for dissatisfaction were residual dorsal hump, under-rotated tip, and a nose that was too small. Among females, the most common reasons for dissatisfaction were residual dorsal hump, under-rotated tip, and bulbous tip. Among dissatisfied patients, females were significantly more likely than males to precisely verbalize the morphologic or functional reason for their dissatisfaction. We found that males had lower satisfaction with rhinoplasty, and were more vague when expressing reasons for dissatisfaction, than females. Social media provides a novel way to understand reasons for patient dissatisfaction after cosmetic surgery. © 2015 The American Society for Aesthetic Plastic Surgery, Inc. Reprints and permission: journals.permissions@oup.com.

Trailing Vortex Measurements in the Wake of a Hovering Rotor Blade with Various Tip Shapes

NASA Technical Reports Server (NTRS)

Martin, Preston B.; Leishman, J. Gordon

2003-01-01

This work examined the wake aerodynamics of a single helicopter rotor blade with several tip shapes operating on a hover test stand. Velocity field measurements were conducted using three-component laser Doppler velocimetry (LDV). The objective of these measurements was to document the vortex velocity profiles and then extract the core properties, such as the core radius, peak swirl velocity, and axial velocity. The measured test cases covered a wide range of wake-ages and several tip shapes, including rectangular, tapered, swept, and a subwing tip. One of the primary differences shown by the change in tip shape was the wake geometry. The effect of blade taper reduced the initial peak swirl velocity by a significant fraction. It appears that this is accomplished by decreasing the vortex strength for a given blade loading. The subwing measurements showed that the interaction and merging of the subwing and primary vortices created a less coherent vortical structure. A source of vortex core instability is shown to be the ratio of the peak swirl velocity to the axial velocity deficit. The results show that if there is a turbulence producing region of the vortex structure, it will be outside of the core boundary. The LDV measurements were supported by laser light-sheet flow visualization. The results provide several benchmark test cases for future validation of theoretical vortex models, numerical free-wake models, and computational fluid dynamics results.

Activities on Facebook Reveal the Depressive State of Users

PubMed Central

Kwak, Jinah

2013-01-01

Background As online social media have become prominent, much effort has been spent on identifying users with depressive symptoms in order to aim at early diagnosis, treatment, and even prevention by using various online social media. In this paper, we focused on Facebook to discern any correlations between the platform’s features and users’ depressive symptoms. This work may be helpful in trying to reach and detect large numbers of depressed individuals more easily. Objective Our goal was to develop a Web application and identify depressive symptom–related features from users of Facebook, a popular social networking platform. Methods 55 Facebook users (male=40, female=15, mean age 24.43, SD 3.90) were recruited through advertisement fliers distributed to students in a large university in Korea. Using EmotionDiary, the Facebook application we developed, we evaluated depressive symptoms using the Center for Epidemiological Studies-Depression (CES-D) scale. We also provided tips and facts about depression to participants and measured their responses using EmotionDiary. To identify the Facebook features related to depression, correlation analyses were performed between CES-D and participants’ responses to tips and facts or Facebook social features. Last, we interviewed depressed participants (CES-D≥25) to assess their depressive symptoms by a psychiatrist. Results Facebook activities had predictive power in distinguishing depressed and nondepressed individuals. Participants’ response to tips and facts, which can be explained by the number of app tips viewed and app points, had a positive correlation (P=.04 for both cases), whereas the number of friends and location tags had a negative correlation with the CES-D scale (P=.08 and P=.045 respectively). Furthermore, in finding group differences in Facebook social activities, app tips viewed and app points resulted in significant differences (P=.01 and P=.03 respectively) between probably depressed and nondepressed individuals. Conclusions Our results using EmotionDiary demonstrated that the more depressed one is, the more one will read tips and facts about depression. We also confirmed depressed individuals had significantly fewer interactions with others (eg, decreased number of friends and location tagging). Our app, EmotionDiary, can successfully evaluate depressive symptoms as well as provide useful tips and facts to users. These results open the door for examining Facebook activities to identify depressed individuals. We aim to conduct the experiment in multiple cultures as well. PMID:24084314

Activities on Facebook reveal the depressive state of users.

PubMed

Park, Sungkyu; Lee, Sang Won; Kwak, Jinah; Cha, Meeyoung; Jeong, Bumseok

2013-10-01

As online social media have become prominent, much effort has been spent on identifying users with depressive symptoms in order to aim at early diagnosis, treatment, and even prevention by using various online social media. In this paper, we focused on Facebook to discern any correlations between the platform's features and users' depressive symptoms. This work may be helpful in trying to reach and detect large numbers of depressed individuals more easily. Our goal was to develop a Web application and identify depressive symptom-related features from users of Facebook, a popular social networking platform. 55 Facebook users (male=40, female=15, mean age 24.43, SD 3.90) were recruited through advertisement fliers distributed to students in a large university in Korea. Using EmotionDiary, the Facebook application we developed, we evaluated depressive symptoms using the Center for Epidemiological Studies-Depression (CES-D) scale. We also provided tips and facts about depression to participants and measured their responses using EmotionDiary. To identify the Facebook features related to depression, correlation analyses were performed between CES-D and participants' responses to tips and facts or Facebook social features. Last, we interviewed depressed participants (CES-D≥25) to assess their depressive symptoms by a psychiatrist. Facebook activities had predictive power in distinguishing depressed and nondepressed individuals. Participants' response to tips and facts, which can be explained by the number of app tips viewed and app points, had a positive correlation (P=.04 for both cases), whereas the number of friends and location tags had a negative correlation with the CES-D scale (P=.08 and P=.045 respectively). Furthermore, in finding group differences in Facebook social activities, app tips viewed and app points resulted in significant differences (P=.01 and P=.03 respectively) between probably depressed and nondepressed individuals. Our results using EmotionDiary demonstrated that the more depressed one is, the more one will read tips and facts about depression. We also confirmed depressed individuals had significantly fewer interactions with others (eg, decreased number of friends and location tagging). Our app, EmotionDiary, can successfully evaluate depressive symptoms as well as provide useful tips and facts to users. These results open the door for examining Facebook activities to identify depressed individuals. We aim to conduct the experiment in multiple cultures as well.

What advice is given to newly qualified doctors on Twitter? An analysis of #TipsForNewDocs tweets.

PubMed

Rashid, Mohammed Ahmed; McKechnie, Doug; Gill, Deborah

2018-07-01

Twitter is a social media platform on which users post very brief messages that can be rapidly communicated across wide geographical areas and audiences. Many doctors use Twitter for personal as well as professional communications and networking. The #TipsForNewDocs hashtag is used on Twitter to give advice to newly qualified doctors as they commence their careers. This study explores the nature and focus of such advice. An analysis of Twitter activity containing the #TipsForNewDocs hashtag was performed using Symplur health care analytics software. Tweets sent during a peak 48-hour period in 2016 (immediately preceding the first day of work for newly qualified UK doctors) were studied. The geographical locations and professional backgrounds of participants were categorised and the content of tweets was subjected to thematic analysis. During 1 and 2 August 2016, 661 unique #TipsForNewDocs tweets were posted. A total of 621 (94.0%) were posted by people in the UK; 522 (79.0%) were posted by doctors, and the remainder by allied health care professionals and patients. The majority of included tweets focused on aspects of professional development, improving personal or professional knowledge, particularly tacit knowledge, and developing 'know-how'. These aspects of professional knowledge have previously been described as fundamental to professional education and training. However, a significant subset of tweets focused on accelerating socialisation into the profession, an essential step in joining a professional community. The tweets relating to socialisation were often humorous and colloquial in nature. Despite their brief and often jocular nature, #TipsForNewDocs tweets provided meaningful advice for newcomers to the profession, often focusing on tacit learning and professional socialisation. Hashtag-driven enquiries can be a valuable and time-efficient way of accessing and sharing tacitly held knowledge. Social media content analysis can provide valuable insights into key educational issues. © 2018 John Wiley & Sons Ltd and The Association for the Study of Medical Education.

Root Growth Patterns and Morphometric Change Based on the Growth Media

NASA Astrophysics Data System (ADS)

Schultz, Eric R.; Paul, Anna-Lisa; Ferl, Robert J.

2016-12-01

Arabidopsis thaliana roots skew with minimal waving in the microgravity environment of the International Space Station. Root skewing and root waving have been studied on the ground as well as in spaceflight, but often using different media types. In this study, Arabidopsis seedlings were grown on nutrient media plates that were comprised of various gelling agents with varied hardness in order to better assess these media for spaceflight research experiments. ImageJ was used to quantify the root morphology of 8-dayold seedlings, while R was used to perform statistical analyses. Root growth was drastically different between Difco agar, agarose, and Phytagel. Additionally, root waving masked skewing in certain media. Regression analysis revealed overall patterns when organized by hardness but also revealed that differences in media type had more of an impact on root growth than hardness itself. Different arrangements of media around the root tip revealed that roots grown on the media surface were longer and had fewer waves per millimeter than roots grown embedded in media. The implications for spaceflight research are discussed.

Proton Improvement Plan-II (PIP-II)

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media , Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For Industry Jobs Interact

Hot-pressed polymer nanofiber supported graphene membrane for high-performance nanofiltration.

PubMed

Wang, Zhao; Sahadevan, Rajesh; Yeh, Che-Ning; Menkhaus, Todd J; Huang, Jiaxing; Fong, Hao

2017-08-04

Graphene oxide (GO) sheets can be readily surface-overlaid on hot-pressed electrospun polyacrylonitrile (PAN) nanofiber membrane to form a continuous and crack-free layer; upon thermal reduction at 150 °C for 12 h, the resulting reduced GO (rGO) layer can reject ∼90% MgSO 4 with high water flux (due to the size exclusion mechanism), making the prepared PAN-rGO membranes promising nanofiltration media for water purification. It is important to note that no delamination of GO/rGO sheet layers has been observed throughout this study. We highlight that a simple processing method (i.e., hot pressing) is critical for the successful preparation of 2D materials (e.g., GO/rGO) based membranes/media. It is envisioned that the reported study can benefit many groups working on various membrane applications of 2D materials; in other words, the hot-pressed electrospun nanofiber membranes could be generally utilized as an innovative type of platform to support various 2D sheets for different separation applications such as highly efficient and cost-effective removal of dissolved components (e.g., organic molecules) and even (hydrated) ions from water.

Dielectric, Piezoelectric, and Vibration Properties of the LiF-Doped (Ba0.95Ca0.05)(Ti0.93Sn0.07)O₃ Lead-Free Piezoceramic Sheets.

PubMed

Cheng, Chien-Min; Chen, Kai-Huang; Lee, Da-Huei; Jong, Fuh-Cheng; Chen, Mei-Li; Chang, Jhih-Kai

2018-01-24

By the conventional solid state reaction method, a small amount of lithium fluoride (LiF) was used as the sintering promoter to improve the sintering and piezoelectric characteristics of (Ba 0.95 Ca 0.05 )(Ti 0.93 Sn 0.07 )O₃ (BCTS) lead-free piezoceramic sheets. Using X-ray diffraction (XRD) and a scanning electron microscope (SEM), the inferences of the crystalline and surface microstructures were obtained and analyzed. Then, the impedance analyzer and d 33 -meter were used to measure the dielectric and piezoelectric characteristics. In this study, the optimum sintering temperature of the BCTS sheets decreased from 1450 °C to 1390 °C due to LiF doping. For the 0.07 wt % LiF-doped BCTS sheets sintered at 1390 °C, the piezoelectric constant (d 33 ) is 413 pC/N, the electric-mechanical coupling coefficient (k p ) is 47.5%, the dielectric loss (tan δ) is 3.9%, and the dielectric constant (ε r ) is 8100, which are all close to or even better than that of the pure undoped BCTS ceramics. The Curie temperature also improved, from 85 °C for pure BCTS to 140 °C for BCTS-0.07 LiF sheets. Furthermore, by using the vibration system and fixing 1.5 g tip mass at the end of the sheets, as the vibration frequency is 20 Hz, the proposed piezoelectric ceramic sheets also reveal a good energy harvesting performance at the maximum output peak voltage of 4.6 V, which is large enough and can be applied in modern low-power electronic products.

A Relationship Between Constraint and the Critical Crack Tip Opening Angle

NASA Technical Reports Server (NTRS)

Johnston, William M.; James, Mark A.

2009-01-01

Of the various approaches used to model and predict fracture, the Crack Tip Opening Angle (CTOA) fracture criterion has been successfully used for a wide range of two-dimensional thin-sheet and thin plate applications. As thicker structure is considered, modeling the full three-dimensional fracture process will become essential. This paper investigates relationships between the local CTOA evaluated along a three-dimensional crack front and the corresponding local constraint. Previously reported tunneling crack front shapes were measured during fracture by pausing each test and fatigue cycling the specimens to mark the crack surface. Finite element analyses were run to model the tunneling shape during fracture, with the analysis loading conditions duplicating those tests. The results show an inverse relationship between the critical fracture value and constraint which is valid both before maximum load and after maximum load.

Combining cell sheet technology and electrospun scaffolding for engineered tubular, aligned, and contractile blood vessels.

PubMed

Rayatpisheh, Shahrzad; Heath, Daniel E; Shakouri, Amir; Rujitanaroj, Pim-On; Chew, Sing Yian; Chan-Park, Mary B

2014-03-01

Herein we combine cell sheet technology and electrospun scaffolding to rapidly generate circumferentially aligned tubular constructs of human aortic smooth muscles cells with contractile gene expression for use as tissue engineered blood vessel media. Smooth muscle cells cultured on micropatterned and N-isopropylacrylamide-grafted (pNIPAm) polydimethylsiloxane (PDMS), a small portion of which was covered by aligned electrospun scaffolding, resulted in a single sheet of unidirectionally aligned cells. Upon cooling to room temperature, the scaffold, its adherent cells, and the remaining cell sheet detached and were collected on a mandrel to generating tubular constructs with circumferentially aligned smooth muscle cells which possess contractile gene expression and a single layer of electrospun scaffold as an analogue to a small diameter blood vessel's internal elastic lamina (IEL). This method improves cell sheet handling, results in rapid circumferential alignment of smooth muscle cells which immediately express contractile genes, and introduction of an analogue to small diameter blood vessel IEL. Copyright © 2013 Elsevier Ltd. All rights reserved.

Efficient Adsorption Characteristics of Pristine and Silver-Doped Graphene Oxide Towards Contaminants: A Potential Membrane Material for Water Purification?

PubMed

Panigrahi, Puspamitra; Dhinakaran, Ashok Kumar; Sekar, Yuvaraj; Ahuja, Rajeev; Hussain, Tanveer

2018-05-16

In this work, we have investigated the potential of pristine and silver (Ag)-functionalized graphene oxide monolayers GO (GO-Ag) as efficient membranes for water filtration. Our first principles calculations based on density functional theory (DFT) reveal the hydrophilic nature of GO surfaces. The phonon frequency calculations within density functional perturbation theory (DFPT) confirmed the stability of GO sheets in aqueous media. Van der Waals-corrected binding energies of GO sheet towards heavy metals suggest that even pristine GO sheets are completely impermeable to various heavy metals like arsenic (As) and lead (Pb). However, compared to GO, the GO-Ag sheets have a much higher affinity towards the three amino acids histidine, phenyl-alanine and tyrosine, which are the main component of a bacteria cell wall. The GO-Ag sheet is found to be extremely efficient for bacteria inactivation. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

High resolution 3D MRI of mouse mammary glands with intra-ductal injection of contrast media

PubMed Central

Markiewicz, Erica; Fan, Xiaobing; Mustafi, Devkumar; Zamora, Marta; Roman, Brian B.; Jansen, Sanaz A.; Macleod, Kay; Conzen, Suzanne D.; Karczmar, Gregory S.

2014-01-01

The purpose of this study was to use high resolution 3D MRI to study mouse mammary gland ductal architecture based on intra-ductal injection of contrast agents. Female FVB/N mice age 12–20 weeks (n = 12), were used in this study. A 34G, 45° tip Hamilton needle with a 25uL Hamilton syringe was inserted into the tip of the nipple. Approximately 20–25uL of a Gadodiamide/Trypan blue/saline solution was injected slowly over one minute into the nipple and duct. To prevent washout of contrast media from ducts due to perfusion, and maximize the conspicuity of ducts on MRI, mice were sacrificed one minute after injection. High resolution 3D T1-weighted images were acquired on a 9.4T Bruker scanner after sacrifice to eliminate motion artifacts and reduce contrast media leakage from ducts. Trypan blue staining was well distributed throughout the ductal tree. MRI showed the mammary gland ductal structure clearly. In spoiled gradient echo T1-weighted images, the signal-to-noise ratio of regions identified as enhancing mammary ducts following contrast injection was significantly higher than that of muscle (p < 0.02) and significantly higher than that of contralateral mammary ducts that were not injected with contrast media (p < 0.0001). The methods described here could be adapted for injection of specialized contrast agents to measure metabolism or target receptors in normal ducts and ducts with in situ cancers. PMID:25179139

Applying Dynamic Wake Models to Induced Power Calculations for an Optimum Rotor

DTIC Science & Technology

2009-08-01

versions being special cases of the general one. Although the rotor blade may be moving at transonic speeds near the tip, the rotor wake is...The effect of a finite number of blades incurs an additional loss in wake energy due to the individual vortex sheets from each blade . In 1929... blades . Up to this point, previous developments have been able to achieve the full description of the wake in all ranges of flight regime

Re-design and fabrication of titanium multi-wall Thermal Protection System (TPS) test panels

NASA Technical Reports Server (NTRS)

Blair, W.; Meaney, J. E., Jr.; Rosenthal, H. A.

1984-01-01

The Titanium Multi-wall Thermal Protection System (TIPS) panel was re-designed to incorporate Ti-6-2-4-2 outer sheets for the hot surface, ninety degree side closures for ease of construction and through panel fastness for ease of panel removal. Thermal and structural tests were performed to verify the design. Twenty-five panels were fabricated and delivered to NASA for evaluation at Langley Research Center and Johnson Space Center.

Get the Lead Out: Facts about Childhood Lead Poisoning [and] Housekeeping Tips To Reduce Lead Exposure [and] Nutrition and Lead Poisoning [and] The Medical Consequences of Lead Poisoning [and] Lead Poisoning for Health Care Providers.

ERIC Educational Resources Information Center

Illinois State Dept. of Public Health, Springfield.

This document is comprised of five fact sheets from the Illinois Department of Public Health regarding childhood lead poisoning. Recent studies claim that childhood lead poisoning can contribute to problems later in life, such as academic failure, juvenile delinquency, and high blood pressure. Directed to parents, caregivers, and health care…

Fabrication and characterization of poly-(ε)-caprolactone and bioactive glass composites for tissue engineering applications.

PubMed

Mohammadkhah, Ali; Marquardt, Laura M; Sakiyama-Elbert, Shelly E; Day, Delbert E; Harkins, Amy B

2015-04-01

Much work has focused on developing synthetic materials that have tailored degradation profiles and physical properties that may prove useful in developing biomaterials for tissue engineering applications. In the present study, three different composite sheets consisting of biodegradable poly-ε-caprolactone (PCL) and varying types of bioactive glass were investigated. The three composites were composed of 50wt.% PCL and (1) 50wt.% 13-93 B3 borate glass particles, (2) 50wt.% 45S5 silicate glass particles, or (3) a blend of 25wt.% 13-93 B3 and 25wt.% 45S5 glass particles. Degradation profiles determined for each composite showed the composite that contained only 13-93 B3 borate glass had a higher degradation rate compared to the composite containing only 45S5 silicate glass. Uniaxial tensile tests were performed on the composites to determine the effect of adding glass to the polymer on mechanical properties. The peak stress of all of the composites was lower than that of PCL alone, but 100% PCL had a higher stiffness when pre-reacted in cell media for 6weeks, whereas composite sheets did not. Finally, to determine whether the composite sheets would maintain neuronal growth, dorsal root ganglia isolated from embryonic chicks were cultured on composite sheets, and neurite outgrowth was measured. The bioactive glass particles added to the composites showed no negative effects on neurite extension, and neurite extension increased on PCL:45S5 PCL:13-93 B3 when pre-reacted in media for 24h. This work shows that composite sheets of PCL and bioactive glass particles provide a flexible biomaterial for neural tissue engineering applications. Copyright © 2015 Elsevier B.V. All rights reserved.

Micropropagation of Rubus and Ribes spp.

PubMed

Dziedzic, Ewa; Jagła, Joanna

2013-01-01

Micropropagation is the most appropriate method for large-scale production of Rubus and Ribes spp. The proliferation rate of Rubus spp. differs in shoot tips and nodal segments. The culture media used for raspberry and blackberry propagation are MS-based supplemented with different combination and ratio of plant growth regulators, depending on the stage of culture. The initiation medium containing 0.4 mg L(-1) BA and 0.1 mg L(-1) IBA is used to stabilize shoot cultures. In multiplication media, concentration of cytokinin is doubled. In vitro rooting of shoots is achieved on media supplemented with 1.0 mg L(-1) IBA. Ribes spp. cultures are initiated from shoot tips, meristem, or dormant buds on MS medium supplemented with 2.0 mg L(-1) BA, 0.5 mg L(-1) IBA, and 0.1 mg L(-1) GA(3.) After stabilization of shoot cultures in 3-4-week time, shoot multiplication is carried out on MS medium containing 1.0 mg L(-1) BA and 0.1 mg L(-1) IBA. Shoots 2 cm long are cultured to rooting on a medium amended with 2.0 mg L(-1) IBA and 5.0 mg L(-1) IAA. Rooted plantlets are transferred to universal peat substrate and acclimatized in the greenhouse.

Long term effects of BAPTA in scala media on cochlear function.

PubMed

Sellick, Peter M

2007-09-01

BAPTA was iontophoresed or allowed to diffuse into the scala media of the first turn of the guinea pig cochlea via pipettes inserted through the round window and basilar membrane. Cochlear action potential (CAP) thresholds for basal turn frequencies were elevated, scala media cochlear microphonic in response to a 207Hz tone were drastically reduced and the distortion products 2f1-f2 and f2-f2 in response to primaries set at 18 and 21.6kHz were eliminated or severely reduced. The animals were recovered and the above measurements repeated between 24 and 240h after the application of BAPTA. In all animals thresholds for basal turn frequencies remained elevated, and the distortion components were severely reduced. The endolymphatic potential (EP), measured through the basilar membrane on recovery, was not significantly different from the values measured before BAPTA was applied. If the effect of BAPTA, in lowering endolymphatic Ca(2+) concentration, is restricted to the destruction of tip links, as has been shown in many other preparations, then these results suggest that this effect has permanent consequences, either because the tip links failed to regenerate or because their destruction precipitated the degeneration of OHCs. These results may have a bearing on the mechanisms behind permanent threshold shift.

Endogenous Sheet-Averaged Tension Within a Large Epithelial Cell Colony.

PubMed

Dumbali, Sandeep P; Mei, Lanju; Qian, Shizhi; Maruthamuthu, Venkat

2017-10-01

Epithelial cells form quasi-two-dimensional sheets that function as contractile media to effect tissue shape changes during development and homeostasis. Endogenously generated intrasheet tension is a driver of such changes, but has predominantly been measured in the presence of directional migration. The nature of epithelial cell-generated forces transmitted over supracellular distances, in the absence of directional migration, is thus largely unclear. In this report, we consider large epithelial cell colonies which are archetypical multicell collectives with extensive cell-cell contacts but with a symmetric (circular) boundary. Using the traction force imbalance method (TFIM) (traction force microscopy combined with physical force balance), we first show that one can determine the colony-level endogenous sheet forces exerted at the midline by one half of the colony on the other half with no prior assumptions on the uniformity of the mechanical properties of the cell sheet. Importantly, we find that this colony-level sheet force exhibits large variations with orientation-the difference between the maximum and minimum sheet force is comparable to the average sheet force itself. Furthermore, the sheet force at the colony midline is largely tensile but the shear component exhibits significantly more variation with orientation. We thus show that even an unperturbed epithelial colony with a symmetric boundary shows significant directional variation in the endogenous sheet tension and shear forces that subsist at the colony level.

The effect of velocity slip and multiple convective boundary conditions in a Darcian porous media with microorganism past a vertical stretching/shrinking sheet

NASA Astrophysics Data System (ADS)

Latiff, Nur Amalina Abdul; Yahya, Elisa; Ismail, Ahmad Izani Md.; Amirsom, Ardiana; Basir, Faisal

2017-08-01

An analysis is carried out to study the steady mixed convective boundary layer flow of a nanofluid in a Darcian porous media with microorganisms past a vertical stretching/shrinking sheet. Heat generation/absorption and chemical reaction effects are incorporated in the model. The partial differential equations are transformed into a system of ordinary differential equations by using similarity transformations generated by scaling group transformations. The transformed equations with boundary conditions are solved numerically. The effects of controlling parameters such as velocity slip, Darcy number, heat generation/absorption and chemical reaction on the skin friction factor, heat transfer, mass transfer and microorganism transfer are shown and discuss through graphs. Comparison of numerical solutions in the present study with the previous existing results in literature are made and comparison results are in very good agreement.

Modeling of light dynamic cone penetration test - Panda 3 ® in granular material by using 3D Discrete element method

NASA Astrophysics Data System (ADS)

Tran, Quoc Anh; Chevalier, Bastien; Benz, Miguel; Breul, Pierre; Gourvès, Roland

2017-06-01

The recent technological developments made on the light dynamic penetration test Panda 3 ® provide a dynamic load-penetration curve σp - sp for each impact. This curve is influenced by the mechanical and physical properties of the investigated granular media. In order to analyze and exploit the load-penetration curve, a numerical model of penetration test using 3D Discrete Element Method is proposed for reproducing tests in dynamic conditions in granular media. All parameters of impact used in this model have at first been calibrated by respecting mechanical and geometrical properties of the hammer and the rod. There is a good agreement between experimental results and the ones obtained from simulations in 2D or 3D. After creating a sample, we will simulate the Panda 3 ®. It is possible to measure directly the dynamic load-penetration curve occurring at the tip for each impact. Using the force and acceleration measured in the top part of the rod, it is possible to separate the incident and reflected waves and then calculate the tip's load-penetration curve. The load-penetration curve obtained is qualitatively similar with that obtained by experimental tests. In addition, the frequency analysis of the measured signals present also a good compliance with that measured in reality when the tip resistance is qualitatively similar.

Feasibility and Perceptions of Cell Phone-Based, Health-Related Communication With Adolescents in an Economically Depressed Area.

PubMed

Sawni, Anju; Cederna-Meko, Crystal; LaChance, Jenny L; Buttigieg, Angie; Le, Quoc; Nunuk, Irene; Ang, Joyce; Burrell, Katherine M

2017-02-01

We examined the feasibility and perception of cell-based (texting, voicemail [VM], and email/social media), health-related communication with adolescents in Genesee County, MI, where 22% reside below the poverty level. Results of an anonymous survey found that 86% of respondents owned a cell phone, 87% had data, 96% texted, 90.5% emailed/used social media, and 68% had VM. Most adolescents were interested in cell-based communication via texting (52%), VM (37%), and email/social media (31%). Interest in types of health communication included appointment reminders (99% texting; 94% VM; 95% email/social media), shot reminders (84.5% texting; 74.5% VM; 81% email/social media), call for test results (71.5% texting; 75% VM; 65% email/social media), medication reminders (63% texting; 54% VM; 58% e-mail/social media), and health tips (36% texting; 18.5% VM; 73% email/social media). Cell-based health-related communication with adolescents is feasible even within low socioeconomic status populations, primarily via texting. Health providers should embrace cell-based patient communication.

Reconnection in the Post-impulsive Phase of Solar Flares

NASA Astrophysics Data System (ADS)

Forbes, Terry G.; Seaton, Daniel B.; Reeves, Katharine K.

2018-05-01

Using a recently developed analytical procedure, we determine the rate of magnetic reconnection in the “standard” model of eruptive solar flares. During the late phase, the neutral line is located near the lower tip of the reconnection current sheet, and the upper region of the current sheet is bifurcated into a pair of Petschek-type shocks. Despite the presence of these shocks, the reconnection rate remains slow if the resistivity is uniform and the flow is laminar. Fast reconnection is achieved only if there is some additional mechanism that can shorten the length of the diffusion region at the neutral line. Observations of plasma flows by the X-ray telescope on Hinode imply that the diffusion region is, in fact, quite short. Two possible mechanisms for reducing the length of the diffusion region are localized resistivity and MHD turbulence.

Quantitation of Cellular Dynamics in Growing Arabidopsis Roots with Light Sheet Microscopy

PubMed Central

Birnbaum, Kenneth D.; Leibler, Stanislas

2011-01-01

To understand dynamic developmental processes, living tissues have to be imaged frequently and for extended periods of time. Root development is extensively studied at cellular resolution to understand basic mechanisms underlying pattern formation and maintenance in plants. Unfortunately, ensuring continuous specimen access, while preserving physiological conditions and preventing photo-damage, poses major barriers to measurements of cellular dynamics in growing organs such as plant roots. We present a system that integrates optical sectioning through light sheet fluorescence microscopy with hydroponic culture that enables us to image, at cellular resolution, a vertically growing Arabidopsis root every few minutes and for several consecutive days. We describe novel automated routines to track the root tip as it grows, to track cellular nuclei and to identify cell divisions. We demonstrate the system's capabilities by collecting data on divisions and nuclear dynamics. PMID:21731697

Battling Sexual Abuse

ERIC Educational Resources Information Center

Dessoff, Alan

2010-01-01

From costly lawsuits on behalf of victims to negative media coverage, districts can face potentially devastating consequences as a result of sexual abuse of their students by district employees. This article offers a few tips on how to battle sexual abuse particularly in school districts. The author stresses that by adopting strong policies that…

The Hidden Formula of Youth Digital Media Engagement. Tips

ERIC Educational Resources Information Center

Reynolds, Rebecca

2009-01-01

The slate of recent reports on youth technology engagement do not explicitly address the construct of "perceived competence," the third main affective state associated with intrinsically-motivated behavior in Edward Deci and Richard Ryan's broader psychological research. In the Spring of 2008, a team of researchers at Syracuse…

Bits and Bytes: A Google Dare

ERIC Educational Resources Information Center

Bennett-Bealer, Nichole

2013-01-01

Educators' reliance on the Internet to research and answer any question, gives rise to a new challenge for students. Like its counterpart at other colleges and universities, Career Services at Burlington County College leads students through a workshop where they analyze their social media presence. The tips and hints help students develop the…

Costs of Emergency Care

MedlinePlus

... All RSS Feeds ACEP In the News Multimedia Image Gallery ACEP Video ACEP Radio ACEP Ads Resources Statistics & Reports Health Policy Campaigns Published Letters Journalism Awards Fact Sheets Social Media Contact Us Site Body Main Content Annals of Emergency Medicine | EMAF Website | ...

Social media use profile, social skills, and nurse-patient interaction among Registered Nurses in tertiary hospitals: A structural equation model analysis.

PubMed

Mariano, Micah Celine O; Maniego, John Christian M; Manila, Hariette Lou Marie D; Mapanoo, Ram Cedrick C; Maquiran, Kerwin Miguel A; Macindo, John Rey B; Tejero, Lourdes Marie S; Torres, Gian Carlo S

2018-04-01

Social media has become increasingly important over the past decades and has been integrated in various environments, including the healthcare setting. Yet, the influence of social media use on the social skills and nurse-patient interaction of nurses is an area in nursing that requires further studies. This study determined the interrelationships among social media use profile, social skills, and nurse-patient interaction of Registered Nurses in tertiary hospitals. Employing structural equation modeling, a descriptive-correlational study was conducted among 212 consecutively-selected nurses from two tertiary hospitals. Consenting respondents completed a two-part survey composed of the respondent profile sheet and the Social Skills Inventory. The respondent profile sheet assessed demographic profile and social media use profile in terms of the mode, frequency, and duration of utilization. Three trained team members observed each nurse-patient dyad and completed the Nurse-Patient Bonding Instrument. A good fit model illustrated the negative effects of frequent social media use to patient openness (β = -0.18, p < 0.05) and engagement (β = -0.11, p ≤ 0.05). Longer use of social media on a daily basis, however, positively affected both dimensions of social skills. Accessing social media platforms using non-handheld devices showed the most influential positive effects to social skills and nurse-patient interaction. Additionally, although verbal social skills positively affected most dimensions of nurse-patient interaction, non-verbal social skills negatively influenced patient engagement (β = -0.19, p = 0.019) and nurse openness (β = -0.38, p ≤ 0.05). The structural model illustrates the effects of using social media on the social skills and nurse-patient interaction of nurses and emphasizes the need for implementing institutional policies on the judicious use and application of social media in the workplace. Further, social skills development programs geared toward having a balanced social skill must be implemented. Copyright © 2018 Elsevier Ltd. All rights reserved.

Filter Media Tests Under Simulated Martian Atmospheric Conditions

NASA Technical Reports Server (NTRS)

Agui, Juan H.

2016-01-01

Human exploration of Mars will require the optimal utilization of planetary resources. One of its abundant resources is the Martian atmosphere that can be harvested through filtration and chemical processes that purify and separate it into its gaseous and elemental constituents. Effective filtration needs to be part of the suite of resource utilization technologies. A unique testing platform is being used which provides the relevant operational and instrumental capabilities to test articles under the proper simulated Martian conditions. A series of tests were conducted to assess the performance of filter media. Light sheet imaging of the particle flow provided a means of detecting and quantifying particle concentrations to determine capturing efficiencies. The media's efficiency was also evaluated by gravimetric means through a by-layer filter media configuration. These tests will help to establish techniques and methods for measuring capturing efficiency and arrestance of conventional fibrous filter media. This paper will describe initial test results on different filter media.

B-scan technique for localization and characterization of fatigue cracks around fastener holes in multi-layered structures

NASA Astrophysics Data System (ADS)

Hopkins, Deborah; Datuin, Marvin; Aldrin, John; Warchol, Mark; Warchol, Lyudmila; Forsyth, David

2018-04-01

The work presented here aims to develop and transition angled-beam shear-wave inspection techniques for crack localization at fastener sites in multi-layer aircraft structures. This requires moving beyond detection to achieve reliable crack location and size, thereby providing invaluable information for maintenance actions and service-life management. The technique presented is based on imaging cracks in "True" B-scans (depth view projected in the sheets along the beam path). The crack traces that contribute to localization in the True B-scans depend on small, diffracted signals from the crack edges and tips that are visible in simulations and experimental data acquired with sufficient gain. The most recent work shows that cracks rotated toward and away from the central ultrasonic beam also yield crack traces in True B-scans that allow localization in simulations, even for large obtuse angles where experimental and simulation results show very small or no indications in the C-scans. Similarly, for two sheets joined by sealant, simulations show that cracks in the second sheet can be located in True B-scans for all locations studied: cracks that intersect the front or back wall of the second sheet, as well as relatively small mid-bore cracks. These results are consistent with previous model verification and sensitivity studies that demonstrate crack localization in True B-scans for a single sheet and cracks perpendicular to the ultrasonic beam.

Cultural Evolutionary Tipping Points in the Storage and Transmission of Information

PubMed Central

Bentley, R. Alexander; O’Brien, Michael J.

2012-01-01

Human culture has evolved through a series of major tipping points in information storage and communication. The first was the appearance of language, which enabled communication between brains and allowed humans to specialize in what they do and to participate in complex mating games. The second was information storage outside the brain, most obviously expressed in the “Upper Paleolithic Revolution” – the sudden proliferation of cave art, personal adornment, and ritual in Europe some 35,000–45,000 years ago. More recently, this storage has taken the form of writing, mass media, and now the Internet, which is arguably overwhelming humans’ ability to discern relevant information. The third tipping point was the appearance of technology capable of accumulating and manipulating vast amounts of information outside humans, thus removing them as bottlenecks to a seemingly self-perpetuating process of knowledge explosion. Important components of any discussion of cultural evolutionary tipping points are tempo and mode, given that the rate of change, as well as the kind of change, in information storage and transmission has not been constant over the previous million years. PMID:23267338

Cultural evolutionary tipping points in the storage and transmission of information.

PubMed

Bentley, R Alexander; O'Brien, Michael J

2012-01-01

Human culture has evolved through a series of major tipping points in information storage and communication. The first was the appearance of language, which enabled communication between brains and allowed humans to specialize in what they do and to participate in complex mating games. The second was information storage outside the brain, most obviously expressed in the "Upper Paleolithic Revolution" - the sudden proliferation of cave art, personal adornment, and ritual in Europe some 35,000-45,000 years ago. More recently, this storage has taken the form of writing, mass media, and now the Internet, which is arguably overwhelming humans' ability to discern relevant information. The third tipping point was the appearance of technology capable of accumulating and manipulating vast amounts of information outside humans, thus removing them as bottlenecks to a seemingly self-perpetuating process of knowledge explosion. Important components of any discussion of cultural evolutionary tipping points are tempo and mode, given that the rate of change, as well as the kind of change, in information storage and transmission has not been constant over the previous million years.

Calcium-regulated in vivo protein phosphorylation in Zea mays L. root tips

NASA Technical Reports Server (NTRS)

Raghothama, K. G.; Reddy, A. S.; Friedmann, M.; Poovaiah, B. W.

1987-01-01

Calcium dependent protein phosphorylation was studied in corn (Zea mays L.) root tips. Prior to in vivo protein phosphorylation experiments, the effect of calcium, ethyleneglycol-bis-(beta-aminoethyl ether)-N-N' -tetraacetic acid (EGTA) and calcium ionophore (A-23187) on phosphorus uptake was studied. Calcium increased phosphorus uptake, whereas EGTA and A-23187 decreased it. Consequently, phosphorus concentration in the media was adjusted so as to attain similar uptake in different treatments. Phosphoproteins were analyzed by two-dimensional gel electrophoresis. Distinct changes in phosphorylation were observed following altered calcium levels. Calcium depletion in root tips with EGTA and A-23187 decreased protein phosphorylation. However, replenishment of calcium following EGTA and ionophore pretreatment enhanced phosphorylation of proteins. Preloading of the root tips with 32P in the presence of EGTA and A-23187 followed by a ten minute calcium treatment, resulted in increased phosphorylation indicating the involvement of calcium, calcium and calmodulin-dependent kinases. Calmodulin antagonist W-7 was effective in inhibiting calcium-promoted phosphorylation. These studies suggest a physiological role for calcium-dependent phosphorylation in calcium-mediated processes in plants.

Dynamic cone penetration tests in granular media: Determination of the tip's dynamic load-penetration curve

NASA Astrophysics Data System (ADS)

Escobar, E.; Benz, M.; Gourvès, R.; Breul, P.

2013-06-01

In this article a two-dimensional discrete numerical model, realized in PFC2D, is presented. This model is used in the dynamic penetration tests in a granular medium. Its objective being the validation of the measurement technique offered by Panda 3® (Benz et al. 2011) which is designed to calculate the tip's load-penetration curve for each impact in the soil where different parameters are used. To do so, we have compared the results obtained by calculation during the impacts to those measured directly in the model of a penetrometer through the installation of the gauges at the cone.

Large Tabular Iceberg, South Atlantic Ocean

NASA Image and Video Library

1991-09-18

This large tabular iceberg, broken off from the Antarctic Ice Sheet, was spotted in the South Atlantic Ocean (57.0S, 57.0W) southeast of the tip of South America as it was slowly being moved north and east by wind, current and tidal influences. This type of iceberg, never to be seen in the northern hemisphere, is typical for Antarctica. Although some such icebergs are as large as 100 km in length, this one measures about 35 by 69 km.

Large Tabular Iceberg, South Atlantic Ocean

NASA Technical Reports Server (NTRS)

1991-01-01

This large tabular iceberg, broken off from the Antarctic Ice Sheet, was spotted in the South Atlantic Ocean (57.0S, 57.0W) southeast of the tip of South America as it was slowly being moved north and east by wind, current and tidal influences. This type of iceberg, never to be seen in the northern hemisphere, is typical for Antarctica. Although some such icebergs are as large as 100 km in length, this one measures about 35 by 69 km.

How to Chair Effective Meetings: A Guide to Group Problem Solving,

DTIC Science & Technology

1975-01-01

Physical Aids: 1. Felt-tip pens 2. Tablets 3. Pencils 4. Three-hole punch 5. Paper clips 6. Masking tape 7. Stapler 8. Water and glasses 9. Ash trays...basic ideas in the speaker’s own words - on large sheets of paper in full view of the group. The other group members have a responsibility under this...agenda handout or placed on chalkboard or paper pad) 2. Other handouts 3. Sign to identify meeting room 4. Name cards (tents) for participants, if needed

Modeling the Effects of Solar Cell Distribution on Optical Cross Section for Solar Panel Simulation

DTIC Science & Technology

2012-09-01

cell material. The solar panel was created as a CAD model and simulated with the imaging facility parameters with TASAT. TASAT uses a BRDF to apply...1 MODELING THE EFFECTS OF SOLAR CELL DISTRIBUTION ON OPTICAL CROSS SECTION FOR SOLAR PANEL SIMULATION Kelly Feirstine Meiling Klein... model of a solar panel with various solar cell tip and tilt distribution statistics. Modeling a solar panel as a single sheet of “solar cell” material

Learning & Growing Together: Understanding and Supporting Your Child's Development = Aprender y crecer juntos: Como comprender y fomentar el desarrollo de sus hijos [with] Tip Sheets: Ideas for Professionals in Programs That Serve Young Children and Their Families.

ERIC Educational Resources Information Center

Lerner, Claire; Dombro, Amy Laura; Powers, Stefanie

Based on the view that the primary caregivers for infants and toddlers are their own best resource for understanding and caring for their child and that parenting is a lifelong learning process, this book provides information and tools to help caregivers build a strong foundation for their child's development. The book, both in English and…

Micromechanical testing of individual collagen fibrils.

PubMed

van der Rijt, Joost A J; van der Werf, Kees O; Bennink, Martin L; Dijkstra, Pieter J; Feijen, Jan

2006-09-15

A novel method based on AFM was used to attach individual collagen fibrils between a glass surface and the AFM tip, to allow force spectroscopy studies of these. The fibrils were deposited on glass substrates that are partly coated with Teflon AF. A modified AFM tip was used to accurately deposit epoxy glue droplets on either end of the collagen fibril that cross the glass-Teflon AF interface, as to such attach it with one end to the glass and the other end to the AFM tip. Single collagen fibrils have been mechanically tested in ambient conditions and were found to behave reversibly up to stresses of 90 MPa. Within this regime a Young's modulus of 2-7 GPa was obtained. In aqueous media, the collagen fibrils could be tested reversibly up to about 15 MPa, revealing Young's moduli ranging from 0.2 to at most 0.8 GPa.

Restoration of uneven illumination in light sheet microscopy images.

PubMed

Uddin, Mohammad Shorif; Lee, Hwee Kuan; Preibisch, Stephan; Tomancak, Pavel

2011-08-01

Light microscopy images suffer from poor contrast due to light absorption and scattering by the media. The resulting decay in contrast varies exponentially across the image along the incident light path. Classical space invariant deconvolution approaches, while very effective in deblurring, are not designed for the restoration of uneven illumination in microscopy images. In this article, we present a modified radiative transfer theory approach to solve the contrast degradation problem of light sheet microscopy (LSM) images. We confirmed the effectiveness of our approach through simulation as well as real LSM images.

Wake Geometry Measurements and Analytical Calculations on a Small-Scale Rotor Model

NASA Technical Reports Server (NTRS)

Ghee, Terence A.; Berry, John D.; Zori, Laith A. J.; Elliott, Joe W.

1996-01-01

An experimental investigation was conducted in the Langley 14- by 22-Foot Subsonic Tunnel to quantify the rotor wake behind a scale model helicopter rotor in forward level flight at one thrust level. The rotor system in this test consisted of a four-bladed fully articulated hub with blades of rectangular planform and an NACA 0012 airfoil section. A laser light sheet, seeded with propylene glycol smoke, was used to visualize the vortex geometry in the flow in planes parallel and perpendicular to the free-stream flow. Quantitative measurements of wake geometric proper- ties, such as vortex location, vertical skew angle, and vortex particle void radius, were obtained as well as convective velocities for blade tip vortices. Comparisons were made between experimental data and four computational method predictions of experimental tip vortex locations, vortex vertical skew angles, and wake geometries. The results of these comparisons highlight difficulties of accurate wake geometry predictions.

Cell sheet-based tissue engineering for fabricating 3-dimensional heart tissues.

PubMed

Shimizu, Tatsuya

2014-01-01

In addition to stem cell biology, tissue engineering is an essential research field for regenerative medicine. In contrast to cell injection, bioengineered tissue transplantation minimizes cell loss and has the potential to repair tissue defects. A popular approach is scaffold-based tissue engineering, which utilizes a biodegradable polymer scaffold for seeding cells; however, new techniques of cell sheet-based tissue engineering have been developed. Cell sheets are harvested from temperature-responsive culture dishes by simply lowering the temperature. Monolayer or stacked cell sheets are transplantable directly onto damaged tissues and cell sheet transplantation has already been clinically applied. Cardiac cell sheet stacking produces pulsatile heart tissue; however, lack of vasculature limits the viable tissue thickness to 3 layers. Multistep transplantation of triple-layer cardiac cell sheets cocultured with endothelial cells has been used to form thick vascularized cardiac tissue in vivo. Furthermore, in vitro functional blood vessel formation within 3-dimensional (3D) tissues has been realized by successfully imitating in vivo conditions. Triple-layer cardiac cell sheets containing endothelial cells were layered on vascular beds and the constructs were media-perfused using novel bioreactor systems. Interestingly, cocultured endothelial cells migrate into the vascular beds and form perfusable blood vessels. An in vitro multistep procedure has also enabled the fabrication of thick, vascularized heart tissues. Cell sheet-based tissue engineering has revealed great potential to fabricate 3D cardiac tissues and should contribute to future treatment of severe heart diseases and human tissue model production.

Giant and Tunable Anisotropy of Nanoscale Friction in Graphene

NASA Astrophysics Data System (ADS)

Capaz, Rodrigo; Menezes, Marcos; Almeida, Clara; de Cicco, Marcelo; Achete, Carlos; Fragneaud, Benjamin; Cançado, Luiz Gustavo; Paupitz, Ricardo; Galvão, Douglas; Prioli, Rodrigo

The nanoscale friction between an atomic force microscopy tip and graphene is investigated using friction force microscopy (FFM). During the tip movement, friction forces are observed to increase and then saturate in a highly anisotropic manner. As a result, the friction coefficient of graphene is highly dependent on the scanning direction: Under some conditions, the energy dissipated along the armchair direction can be 80% higher than along the zigzag direction. In comparison, for highly-oriented pyrolitic graphite (HOPG), the friction anisotropy between armchair and zigzag directions is only 15%. This giant friction anisotropy in graphene results from anisotropies in the amplitudes of flexural deformations of the graphene sheet driven by the tip movement, not present in HOPG. The effect can be seen as a novel manifestation of the classical phenomenon of Euler buckling at the nanoscale, which provides the non-linear ingredients that amplify friction anisotropy. Simulations based on a novel version of the 2D Tomlinson model (modified to include the effects of flexural deformations), as well as fully atomistic molecular dynamics simulations and first-principles density-functional theory (DFT) calculations, are able to reproduce and explain the experimental observations.

Giant and Tunable Anisotropy of Nanoscale Friction in Graphene

NASA Astrophysics Data System (ADS)

Almeida, Clara M.; Prioli, Rodrigo; Fragneaud, Benjamin; Cançado, Luiz Gustavo; Paupitz, Ricardo; Galvão, Douglas S.; de Cicco, Marcelo; Menezes, Marcos G.; Achete, Carlos A.; Capaz, Rodrigo B.

2016-08-01

The nanoscale friction between an atomic force microscopy tip and graphene is investigated using friction force microscopy (FFM). During the tip movement, friction forces are observed to increase and then saturate in a highly anisotropic manner. As a result, the friction forces in graphene are highly dependent on the scanning direction: under some conditions, the energy dissipated along the armchair direction can be 80% higher than along the zigzag direction. In comparison, for highly-oriented pyrolitic graphite (HOPG), the friction anisotropy between armchair and zigzag directions is only 15%. This giant friction anisotropy in graphene results from anisotropies in the amplitudes of flexural deformations of the graphene sheet driven by the tip movement, not present in HOPG. The effect can be seen as a novel manifestation of the classical phenomenon of Euler buckling at the nanoscale, which provides the non-linear ingredients that amplify friction anisotropy. Simulations based on a novel version of the 2D Tomlinson model (modified to include the effects of flexural deformations), as well as fully atomistic molecular dynamics simulations and first-principles density-functional theory (DFT) calculations, are able to reproduce and explain the experimental observations.

High resolution 3D MRI of mouse mammary glands with intra-ductal injection of contrast media.

PubMed

Markiewicz, Erica; Fan, Xiaobing; Mustafi, Devkumar; Zamora, Marta; Roman, Brian B; Jansen, Sanaz A; Macleod, Kay; Conzen, Suzanne D; Karczmar, Gregory S

2015-01-01

The purpose of this study was to use high resolution three-dimensional (3D) magnetic resonance imaging (MRI) to study mouse mammary gland ductal architecture based on intra-ductal injection of contrast agents. Female FVB/N mice age 12-20 weeks (n=12), were used in this study. A 34G, 45° tip Hamilton needle with a 25μL Hamilton syringe was inserted into the tip of the nipple. Approximately 20-25μL of a Gadodiamide/Trypan blue/saline solution was injected slowly over one minute into the nipple and duct. To prevent washout of contrast media from ducts due to perfusion, and maximize the conspicuity of ducts on MRI, mice were sacrificed one minute after injection. High resolution 3D T1-weighted images were acquired on a 9.4T Bruker scanner after sacrifice to eliminate motion artifacts and reduce contrast media leakage from ducts. Trypan blue staining was well distributed throughout the ductal tree. MRI showed the mammary gland ductal structure clearly. In spoiled gradient echo T1-weighted images, the signal-to-noise ratio of regions identified as enhancing mammary ducts following contrast injection was significantly higher than that of muscle (p<0.02) and significantly higher than that of contralateral mammary ducts that were not injected with contrast media (p<0.0001). The methods described here could be adapted for injection of specialized contrast agents to measure metabolism or target receptors in normal ducts and ducts with in situ cancers. Copyright © 2014 Elsevier Inc. All rights reserved.

Effect of the first federally funded US antismoking national media campaign.

PubMed

McAfee, Tim; Davis, Kevin C; Alexander, Robert L; Pechacek, Terry F; Bunnell, Rebecca

2013-12-14

Every year, smoking kills more than 5 million people globally, including 440,000 people in the USA, where the long-term decline in smoking prevalence has slowed. The US Centers for Disease Control and Prevention (CDC) delivered a national, 3-month antismoking campaign called Tips From Former Smokers (Tips) that started in March, 2012, in which hard-hitting, emotionally evocative television advertising was featured, depicting smoking-related suffering in real people. We aimed to assess the effects of the Tips campaign. We undertook baseline and follow-up surveys of nationally representative cohorts of adult smokers and non-smokers. The national effect of the Tips campaign was estimated by applying rates of change in the cohort before and after the campaign to US census data. 3051 smokers and 2220 non-smokers completed baseline and follow-up assessments. 2395 (78%) smokers and 1632 (74%) non-smokers recalled seeing at least one Tips advertisement on television during the 3-month campaign. Quit attempts among smokers rose from 31.1% (95% CI 30.3-31.9) at baseline to 34.8% (34.0-35.7) at follow-up, a 12% relative increase. The prevalence of abstinence at follow-up among smokers who made a quit attempt was 13.4% (95% CI 9.7-17.2). Nationally, an estimated 1.64 million additional smokers made a quit attempt, and 220,000 (95% CI 159,000-282,000) remained abstinent at follow-up. Recommendations by non-smokers to quit grew from 2.6% at baseline to 5.1% at follow-up, and the prevalence of people talking with friends and family about the dangers of smoking rose from 31.9% (95% CI 31.3-32.5) to 35.2% (34.6-35.9), resulting in an estimated 4.7 million additional non-smokers recommending cessation services and more than 6 million talking about the dangers of smoking. The high-exposure Tips media campaign was effective at increasing population-level quit attempts. The growth in smokers who quit and became sustained quitters could have added from a third to almost half a million quality-adjusted life-years to the US population. Expanded implementation of similar campaigns globally could accelerate progress on the WHO Framework Convention on Tobacco Control and reduce smoking prevalence globally. CDC, US Department of Health and Human Services. Copyright © 2013 Elsevier Ltd. All rights reserved.

Impact of a U.S. Antismoking National Media Campaign on Beliefs, Cognitions and Quit Intentions

ERIC Educational Resources Information Center

Duke, Jennifer C.; Davis, Kevin C.; Alexander, Robert L.; MacMonegle, Anna J.; Fraze, Jami L.; Rodes, Robert M.; Beistle, Diane M.

2015-01-01

In 2012, the Centers for Disease Control and Prevention launched a national tobacco education campaign, "Tips From Former Smokers," that consisted of graphic, emotionally evocative, testimonial-style advertisements. This longitudinal study examines changes in beliefs, tobacco-related cognitions and intentions to quit smoking among U.S.…

Dialogue: A Teaching Guide to Nuclear Issues.

ERIC Educational Resources Information Center

Educators for Social Responsibility, Cambridge, MA.

Materials in this manual are designed to help educators raise the issue of nuclear war through a "day of dialog" on the subject. There are seven sections. Section 1 contains a project reationale; suggestions for implementation; methods for meeting resistance; tips for schoolwide, parent-teacher, and community discussion; uses of the media; and…

The Components of Great Sex: Sexuality Education for People Who Desire to Scale the Heights of Optimal Sexuality

ERIC Educational Resources Information Center

Wampold, Charles H.

2014-01-01

Ubiquitous "sex tips" in popular media evidence an unquenchable public interest in learning how to experience "great sex," and studies confirm that a great sexual relationship correlates to general relationship satisfaction, which in turn correlates to overall happiness. However, sexologists have paid scant attention to…

The State of the Digital Humanities: A Report and a Critique

ERIC Educational Resources Information Center

Liu, Alan

2012-01-01

The scholarly field of the digital humanities has recently expanded and integrated its fundamental concepts, historical coverage, relationship to social experience, scale of projects, and range of interpretive approaches. All this brings the overall field (including the related area of new media studies) to a tipping point where it has the…

Educating Policymakers: 2006 NPS Arms Educators

ERIC Educational Resources Information Center

Techniques: Connecting Education and Careers, 2006

2006-01-01

This article reports that at the 2006 ACTE National Policy Seminar, nearly 500 career and technical educators gathered in Washington, DC, in March to learn about what is happening with Perkins, receive tips on working with the media, and voice their opinions with their federal representatives. Attendees left this session armed with the statistics…

News: A Consumer's Guide.

ERIC Educational Resources Information Center

Doig, Ivan; Doig, Carol

A guide to news media, this book describes how to tell when a report is biased; provides tips on spotting hoaxes and public relations ploys in the news; gives standards to judge expert opinion and reliable sources; lists critics and other sources of help for the news consumer; discusses the endless contest among politicians, newsmen, and…

The Shoestring Library

ERIC Educational Resources Information Center

Fullner, Sheryl Kindle

2010-01-01

An organized collection of budget saving methods, materials, and strategies, these tips are all tried-and-true examples of ways to stretch the media specialist's budget and time, and change even the drabbest library into an inviting oasis of learning. Makeovers are mesmerizing. Whether it is the 400-pound man who turns into a hunk or a hovel that…

Teaching Information Ethics to High School Students

ERIC Educational Resources Information Center

Lehman, Kathy

2009-01-01

The new AASL standards clearly spell out ethical responsibilities, which school librarians strive to instill and model as they work with staff and students. In this article, the author presents the AASL standards together with some tips and lesson ideas which she and her library partner have put into practice within their library media program.

Teaching Tip: Developing an Intercollegiate Twitter Forum to Improve Student Exam Study and Digital Professionalism.

PubMed

Whiting, Martin; Kinnison, Tierney; Mossop, Liz

#VetFinals has been developed as a novel online Twitter teaching event designed to support intercollegiate veterinary teaching using social media. Previous studies in other fields have suggested that Twitter use within universities may have benefits for undergraduate education. This "teaching tip" paper describes a project using Twitter to host online exam study sessions. The project has been a highly successful collaborative effort between the Royal Veterinary College and Nottingham Veterinary School in the UK. Over 4 years, the #VetFinals project has developed into a long-term, self-sustaining enterprise. This initiative provides a semi-structured means for student exam preparation with direct real-time input from a faculty member. It also creates a network of peers both horizontally across institutions and vertically throughout year groups. Based on similar initiatives in other disciplines, an anticipated outcome of this project was to contribute to student online professionalism. This could help address the veterinary community's recently highlighted problems with professional conduct and appropriate use of social media. Analysis of the success of this endeavor will be available in a future publication.

Oriental nose elongation using an L-shaped polyethylene sheet implant for combined septal spreading and extension.

PubMed

Zhou, Jia; Huang, Xiaolu; Zheng, Danning; Li, Haizhou; Herrler, Tanja; Li, Qingfeng

2014-04-01

The currently recommended strategies for short nose elongation were designed primarily for the Caucasian nasal framework. For Oriental patients, more elongation often is required because a hypoplastic septal cartilage requires more elongation, resulting in a higher risk of complications. This report proposes a modified technique for Oriental nose elongation, which adjusts the pressure points after nasal elongation using an L-shaped implant. Between January 2007 and December 2009, 58 patients underwent Oriental nose elongation using an L-shaped, porous, high-density polyethylene sheet implant. Augmentation rhinoplasty and conchal cartilage shield grafts were performed depending on the nasal shape. Pre- and postoperative nasal length, height, and projection as well as columella-labial angle, columella-lobular angle, and nasal tip angle were measured and compared. A patient satisfaction survey was performed postoperatively. All occurring complications were recorded. The postoperative nasal length was significantly elongated from 47.0±10.4 mm to 49.3±10.1 mm (p=0.003), and the nasal height increased significantly from 48.5±9.1 mm to 50.4±8.5 mm (p=0.011). The initially obtuse columella-labial angle improved significantly from 100.8°±12.1° to 92.5°±15.5° (p=0.014). No significant changes were found regarding nasal projection, nasal tip angle, or columella-lobular angle. The majority of the patients (91.3%) were highly satisfied or satisfied with the aesthetic results. A major complication in terms of implant exposure was observed in one case. The minor complications included stiffness of the nasal tip (3 patients) and tip redness (1 patient). In Oriental nose elongation, the use of an L-shaped graft is a feasible and safe treatment option that allows for an excellent aesthetic outcome and reduces the incidence of complications. This journal requires that authors assign a level of evidence to each submission to which Evidence-Based Medicine rankings are applicable. This excludes Review Articles, Book Reviews, and manuscripts that concern Basic Science, Animal Studies, Cadaver Studies, and Experimental Studies. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .

Influence of cytokinins, auxins and polyamines on in vitro mass multiplication of cotton (Gossypium hirsutum L. cv. SVPR2).

PubMed

Ganesan, M; Jayabalan, N

2006-06-01

In the present investigation, the influence of different forms of cytokinins, auxins and polyamines were tested for mass multiplication and regeneration of cotton. Initially, for the identification of effective concentration for multiple shoot induction, various concentrations of BAP, Kin and 2iP along with IAA and NAA were tested. Among tested concentrations, media fortified with MS salts; B5 vitamins; 30 g/l, glucose; 2.0 mg/l, 2iP; 2.0 mg/l, IAA and 0.7 % agar showed best response for multiplication of shoot tip explants (20 shoots per shoot tip explants). In nodal explants, maximum of 18.6 shoots were obtained in the media fortified with MS salts, B5 vitamins, 30 g/l, glucose, 2.0 mg/l, 2iP, 1.0 mg/l, NAA and 0.7 % agar. Effect of different concentrations of polyamines like spermidine and putrescine were also tested along with the above said multiplication media. Among the various treatments, 20 mg/l of putrescine showed best response and the multiple of shoots were increased to 26.5 shoots per shoot tip explants and 24.5 shoots per nodal explants. Elongation of shoots was achieved on multiple shoot induction medium. Significant number of roots were initiated in the medium supplemented with MS salts, vitamin B5 and IBA (2.0 mg/l). The frequency of root induction was increased by addition of, PVP (10 mg/l) along with root induction medium and after 2 weeks, the roots reached the maximum length of 22 cm. Further, these plantlets were hardened by using sand, soil and vermiculate in 1:1:1 ratio. The hardened plants were transferred to the environmental growth chamber for proper acclimatization. The hardened plants were then transferred to field for boll yielding and they exhibited 100% survival.

NCIP Profiles, 1-5, 1995.

ERIC Educational Resources Information Center

NCIP Profiles, 1995

1995-01-01

This set of information sheets is intended to improve practice in special education through technology, media, and materials. The first information profile introduces NCIP (the National Center to Improve Practice), gives an example of how one special education administrator uses NCIP resources, and offers suggestions for facilitating NCIP…

One-step leapfrog ADI-FDTD method for simulating electromagnetic wave propagation in general dispersive media.

PubMed

Wang, Xiang-Hua; Yin, Wen-Yan; Chen, Zhi Zhang David

2013-09-09

The one-step leapfrog alternating-direction-implicit finite-difference time-domain (ADI-FDTD) method is reformulated for simulating general electrically dispersive media. It models material dispersive properties with equivalent polarization currents. These currents are then solved with the auxiliary differential equation (ADE) and then incorporated into the one-step leapfrog ADI-FDTD method. The final equations are presented in the form similar to that of the conventional FDTD method but with second-order perturbation. The adapted method is then applied to characterize (a) electromagnetic wave propagation in a rectangular waveguide loaded with a magnetized plasma slab, (b) transmission coefficient of a plane wave normally incident on a monolayer graphene sheet biased by a magnetostatic field, and (c) surface plasmon polaritons (SPPs) propagation along a monolayer graphene sheet biased by an electrostatic field. The numerical results verify the stability, accuracy and computational efficiency of the proposed one-step leapfrog ADI-FDTD algorithm in comparison with analytical results and the results obtained with the other methods.

Modelisation of the SECMin molten salts environment

NASA Astrophysics Data System (ADS)

Lucas, M.; Slim, C.; Delpech, S.; di Caprio, D.; Stafiej, J.

2014-06-01

We develop a cellular automata modelisation of SECM experiments to study corrosion in molten salt media for generation IV nuclear reactors. The electrodes used in these experiments are cylindrical glass tips with a coaxial metal wire inside. As the result of simulations we obtain the current approach curves of the electrodes with geometries characterized by several values of the ratios of glass to metal area at the tip. We compare these results with predictions of the known analytic expressions, solutions of partial differential equations for flat uniform geometry of the substrate. We present the results for other, more complicated substrate surface geometries e. g. regular saw modulated surface, surface obtained by Eden model process, ...

Spring back of infinite honeycomb sheets beyond plastic deformation

NASA Astrophysics Data System (ADS)

Bonfanti, A.; Bhaskar, A.

2015-02-01

Cellular structures are promising for applications where high stiffness and strength are required with the minimal use of material. They are often used in applications where the plastic deformation plays an important role, such as those involving crashworthiness, energy absorption, and stents. The elastic analysis of a honeycomb sheet has been carried out in the past [1]. The present analysis extends this classical work in the elasto-plastic regime. Recoil analysis due to elastic recovery is absent from the published literature. This work aims to develop an analytical model to calculate the spring back for a simplified case, that of an infinite honeycomb sheet. An elastic-perfectly plastic material model is assumed. The recoil for a clamped beam with a load and moment applied at the free edge is analytically calculated first. This is carried out by relating the stress distribution of the cross section to the final deformed shape. The part corresponding to the elastic contribution is subsequently subtracted in order to obtain the final configuration after the external load is removed. This simple elasto-plastic analysis is then incorporated into the analysis of an infinite sheet made of uniform hexagonal cells. The translational symmetry of the lattice is exploited along with the analysis of a beam under tip loading through to plastic stage and recoil. The final shape of the struts upon the removal of the remote stress is completely determined by the plastic deformation which cannot be recovered. The expression for the beam thus obtained is then used to build an analytical model for an infinite honeycomb sheet loaded in both directions.

[Developing patient information sheets in general practice. Proposal for a methodology].

PubMed

Sustersic, Mélanie; Meneau, Aurélia; Drémont, Roger; Paris, Adeline; Laborde, Laurent; Bosson, Jean-Luc

2008-12-15

Health information is patients' wish and right. For general practitioners, it is a duty, a legal obligation and a pre-requisite in any preventive approach. Written information must complete oral information since it improves health care quality. However, in general practice, there are no patient documents which are scientifically valid, understandable and efficient in terms of communication. To develop a method for creating patient information sheets and to experiment its feasibility through the development of 125 sheets focused on the most common clinical conditions in general practice. Research and literature review pour the development of specifications, and creation of 125 sheets following these specifications. The specifications developed consist of the 10 following steps: selection of the topic and the objectives, literature review, selection of the sections, drafting, validation of the scientific contents, assessment among patients, validation of the layout, selection of the media, delivery to patients and update. Following these specifications, we developed 125 information sheets. Each of these was reviewed by several physicians and assessed with R. Flesh readability test (the established acceptable threshold value was 40). The 30 sheets associated with the lowest scores were selected and reviewed to improve their overall readability. Even though some difficulties cannot be avoided when developing patient information sheets, each physician or physician association can create its own documents following the proposed specifications and thus deliver a customized message.

Mesenchymal stem cell sheets exert anti-stenotic effects in a rat arterial injury model.

PubMed

Homma, Jun; Sekine, Hidekazu; Matsuura, Katsuhisa; Kobayashi, Eiji; Shimizu, Tatsuya

2018-05-04

Restenosis after catheter or surgical intervention substantially affects the prognosis of arterial occlusive disease. Mesenchymal stem cells (MSCs) may have anti-stenotic effects on injured arteries. MSC transplantation from the adventitial side of an artery is safer than endovascular transplantation but has not been extensively examined. In this study, a rat model of femoral artery injury was used to compare the anti-stenotic effects of transplanted cell sheets and transplanted cell suspensions. Rat adipose-derived stem cells (ASCs) were used as the source of MSCs. For both cell sheets and suspensions, 6×106 MSCs were transplanted on the day of arterial injury. MSC sheets attenuated neointimal hyperplasia more than MSC suspensions (intima-to-media ratio in haematoxylin/eosin-stained sections: 0.55±0.13 vs. 1.14±0.12; P<0.05). Cell engraftment (assessed by immunohistochemistry or bioluminescence imaging of luciferase-expressing cells), arterial re-endothelialisation (evaluated by immunohistochemical staining for rat endothelial cell antigen-1) and restriction of vascular smooth muscle cell proliferation in the neointima (double-staining of alpha-smooth muscle actin and phospho-histone H3) were greater when MSC sheets were applied than when MSC suspensions were used. In conclusion, MSC sheets exhibited better anti-stenotic and cell engraftment properties than MSC suspensions. MSC sheet transplantation from the adventitial side is a promising therapy for prevention of arterial restenosis.

Analyses of Buckling and Stable Tearing in Thin-Sheet Materials

NASA Technical Reports Server (NTRS)

Seshadri, B. R.; Newman, J. C., Jr.

1998-01-01

This paper was to verify the STAGS (general shell, geometric and material nonlinear) code and the critical crack tip opening angle (CTOA) fracture criterion for predicting stable tearing in cracked panels that fail with severe out of plane buckling. Materials considered ranged from brittle to ductile behavior. Test data used in this study are reported elsewhere. The STAGS code was used to model stable tearing using a critical CTOA value that was determined from a cracked panel that was 'restrained' from buckling. ne analysis methodology was then used to predict the influence of buckling on stable tearing and failure loads. Parameters like crack length to specimen width ratio, crack configuration, thickness, and material tensile properties had a significant influence on the buckling behavior of cracked thin sheet materials. Experimental and predicted results showed a varied buckling response for different crack length to sheet thickness ratios because different buckling modes were activated. Effects of material tensile properties and fracture toughness on buckling response were presented. The STAGS code and the CTOA fracture criterion were able to predict the influence of buckling on stable tearing behavior and failure loads on a variety of materials and crack configurations.

Past, present, and future of sublimation transfer imaging

NASA Astrophysics Data System (ADS)

Akada, Masanori

1990-07-01

SONY's announcement of tlavica system shaked the world in 1981. In the new nonphotographic imaging system, image is acquired with CCD to be converted into electric image-signal, stored in magnetic recording media,displayed on a CR1 and printed on a special sheet. To get a hard copy, Sublimation Transfer technology was developed. That announcement brought about world-wide R&D of competitive color imaging systems: Ink-jet, Wax transfer,. Sublimation Transfer(ST) and Electrophotography. In spite of much effort,most of those were insufficient for getting a good hard copy. Developing sufficient ST recording media, Dai Nippon Printing started ST recording media business in 1986. It was the first manufacturing scale production and sale of ST recording media in the world. Nowadays ST technology is known for its advantages: high image quality, consistency from copy to copy, smooth tone-reproduction from high-light to maximum density, and easiness to use. In the following paper progress of ST recording media and the present situation and future markets of the media will be presented.

Dynamics of proteins aggregation. II. Dynamic scaling in confined media

NASA Astrophysics Data System (ADS)

Zheng, Size; Shing, Katherine S.; Sahimi, Muhammad

2018-03-01

In this paper, the second in a series devoted to molecular modeling of protein aggregation, a mesoscale model of proteins together with extensive discontinuous molecular dynamics simulation is used to study the phenomenon in a confined medium. The medium, as a model of a crowded cellular environment, is represented by a spherical cavity, as well as cylindrical tubes with two aspect ratios. The aggregation process leads to the formation of β sheets and eventually fibrils, whose deposition on biological tissues is believed to be a major factor contributing to many neuro-degenerative diseases, such as Alzheimer's, Parkinson's, and amyotrophic lateral sclerosis diseases. Several important properties of the aggregation process, including dynamic evolution of the total number of the aggregates, the mean aggregate size, and the number of peptides that contribute to the formation of the β sheets, have been computed. We show, similar to the unconfined media studied in Paper I [S. Zheng et al., J. Chem. Phys. 145, 134306 (2016)], that the computed properties follow dynamic scaling, characterized by power laws. The existence of such dynamic scaling in unconfined media was recently confirmed by experiments. The exponents that characterize the power-law dependence on time of the properties of the aggregation process in spherical cavities are shown to agree with those in unbounded fluids at the same protein density, while the exponents for aggregation in the cylindrical tubes exhibit sensitivity to the geometry of the system. The effects of the number of amino acids in the protein, as well as the size of the confined media, have also been studied. Similarities and differences between aggregation in confined and unconfined media are described, including the possibility of no fibril formation, if confinement is severe.

Practical tips for managing LinkedIn and Facebook (on top of everything else).

PubMed

Meerschaert, Carol

2012-01-01

Time-saving steps and strategies to help you make room for social media in your crowded day. I bet you've never thought to yourself, "I'd like more work to do". So how can you possibly accomplish everything and manage your association's LinkedIn group and Facebook page as well?

Ectomycorrihizae of Table Mountain Pine and the Influence of Prescribed Burning on their Survival

Treesearch

Lisa E. Ellis; Thomas A. Waldrop; Frank H. Tainter

2002-01-01

High-intensity prescribed fires have been recommended to regenerate Table Mountain pine (Pinus pungens). However, tests of these burns produced few seedlings, possibly due to soil sterilization. This study examined abundance of mycorrhizal root tips in the field after a high-intensity fire and in the laboratory after exposing rooting media to...

Spatially discrete thermal drawing of biodegradable microneedles for vascular drug delivery.

PubMed

Choi, Chang Kuk; Lee, Kang Ju; Youn, Young Nam; Jang, Eui Hwa; Kim, Woong; Min, Byung-Kwon; Ryu, WonHyoung

2013-02-01

Spatially discrete thermal drawing is introduced as a novel method for the fabrication of biodegradable microneedles with ultra-sharp tip ends. This method provides the enhanced control of microneedle shapes by spatially controlling the temperature of drawn polymer as well as drawing steps and speeds. Particular focus is given on the formation of sharp tip ends of microneedles at the end of thermal drawing. Previous works relied on the fracture of polymer neck by fast drawing that often causes uncontrolled shapes of microneedle tips. Instead, this approach utilizes the surface energy of heated polymer to form ultra-sharp tip ends. We have investigated the effect of such temperature control, drawing speed, and drawing steps in thermal drawing process on the final shape of microneedles using biodegradable polymers. XRD analysis was performed to analyze the effect of thermal cycle on the biodegradable polymer. Load-displacement measurement also showed the dependency of mechanical strengths of microneedles on the microneedle shapes. Ex vivo vascular tissue insertion and drug delivery demonstrated microneedle insertion to tunica media layer of canine aorta and drug distribution in the tissue layer. Copyright © 2012 Elsevier B.V. All rights reserved.

Dielectric-loaded coaxial-slot antenna for interstitial microwave hyperthermia: longitudinal control of heating patterns.

PubMed

Hamada, L; Saito, K; Yoshimura, H; Ito, K

2000-01-01

In this paper, the microwave interstitial antenna with the dielectric load in part near the tip is introduced to realize the tip-heating and to improve the dependence of the heating patterns on the insertion depth. Numerical simulations using the Finite Difference Time Domain (FDTD) method have been conducted at the frequency of 915 MHz for four different configurations of the coaxial-slot antenna inserted into a catheter: the media between the antenna and the catheter are (a) no, (b) a thin air layer, (c) a thin dielectric layer, and (d) a thin air layer and a dielectric load in part near the tip. The diameter of the antenna including the catheter is sufficiently small for minimally invasive therapy. Comparison of the SARs for the four configurations makes it clear that the dielectric-loaded antenna can realize the best tip-heating and suppress the hot spot near the surface of the human body. Dependence of the SAR distributions on the insertion depth of the antenna has also been examined. It is found from the investigation that the dielectric-loaded antenna has little dependence on the insertion depth.

Coordinated Specialty Care Fact Sheet and Checklist

MedlinePlus

... Join A Study News & Events News & Events Home Science News Meetings and Events Multimedia Social Media Press Resources Newsletters NIMH News Feeds About Us About Us Home About the Director Advisory Boards and ... of Mental Health Office of Science Policy, Planning, and Communications 6001 Executive Boulevard, Room ...

Audiovisual Materials.

ERIC Educational Resources Information Center

American Council on Education, Washington, DC. HEATH/Closer Look Resource Center.

The fact sheet presents a suggested evaluation framework for use in previewing audiovisual materials, a list of selected resources, and an annotated list of films which were shown at the AHSSPPE '83 Media Fair as part of the national conference of the Association on Handicapped Student Service Programs in Postsecondary Education. Evaluation…

A Novel Light Trapping Phenomenon in Fluid Media.

ERIC Educational Resources Information Center

Devlin, J. C.; Tolles, W. M.

1979-01-01

Describes an experiment on light trapping in thin liquid films. Injection of a thin layer of solution at the boundary of a moving solvent is utilized to create a thin fluid sheet having an index of refraction greater than that of the surrounding medium. (Author/SA)

Compendium of CARDEROCKDIV Articles Published in Navy Domestic Technology Transfer Fact Sheet, January 1990 through December 1992

DTIC Science & Technology

1992-12-01

longer in the Gulf of Mexico and the patrol, in such areas as th(. Florida Straits have learned what Yucatan Peninsula and from naval Ii means to look down...same performed on conventional deep - containing shallow cracks aW/W < J value have markedly different crack specimens The increa-ed 02, are commonly...the Jc values ’for characterization of the crack-tip atW ratio effects on the measured corresponding deep -crack spec- stress field Moreover, these

Near-Field Scanning Optical Microscopy of Soft, Biological, or Rough Objects in Aqueous Environment: Challenges and some Remedies to Circumvent

NASA Technical Reports Server (NTRS)

Vikram, C. S.; Witherow, W. K.

1999-01-01

Near-field scanning optical microscopy is an established technique for sub-wavelength spatial resolution in imaging, spectroscopy, material science, surface chemistry, polarimetry, etc. A significant amount of confidence has been established for thin hard specimens in air. However when soft, biological, rough, in aqueous environment object, or a combination is involved, the progress has been slow. The tip-sample mechanical interaction, heat effects to sample, drag effects to the probe, difficulty in controlling tip-sample separation in case of rough objects, light scattering from sample thickness, etc. create problems. Although these problems are not even fully understood, there have been attempts to study them with the aim of performing reliable operations. In this review we describe these attempts. Starting with general problems encountered, various effects like polarization, thermal, and media are covered. The roles of independent tip-sample distance control tools in the relevant situations are then described. Finally progress in fluid cell aspect has been summarized.

From 1D Polymers to 2D Polymers: Preparation of Free-Standing Single-Monomer-Thick Two-Dimensional Conjugated Polymers in Water.

PubMed

Zhang, Na; Wang, Taisheng; Wu, Xing; Jiang, Chen; Zhang, Taiming; Jin, Bangkun; Ji, Hengxing; Bai, Wei; Bai, Ruke

2017-07-25

Recently, investigation on two-dimensional (2D) organic polymers has made great progress, and conjugated 2D polymers already play a dynamic role in both academic and practical applications. However, a convenient, noninterfacial approach to obtain single-layer 2D polymers in solution, especially in aqueous media, remains challenging. Herein, we present a facile, highly efficient, and versatile "1D to 2D" strategy for preparation of free-standing single-monomer-thick conjugated 2D polymers in water without any aid. The 2D structure was achieved by taking advantage of the side-by-side self-assembly of a rigid amphiphilic 1D polymer and following topochemical photopolymerization in water. The spontaneous formation of single-layer polymer sheets was driven by synergetic association of the hydrophobic interactions, π-π stacking interactions, and electrostatic repulsion. Both the supramolecular sheets and the covalent sheets were confirmed by spectroscopic analyses and electron microscope techniques. Moreover, in comparison of the supramolecular 2D polymer, the covalent 2D polymer sheets exhibited not only higher mechanical strength but also higher conductivity, which can be ascribed to the conjugated network within the covalent 2D polymer sheets.

Growth of Transgressive Sills in Mechanically Layered Media: Faroe Islands, NE Atlantic Margin

NASA Astrophysics Data System (ADS)

Walker, R. J.

2014-12-01

Igneous sills represent an important contribution to upper crustal magma transport, acting as magma conduits and stores (i.e. as sill networks, or as nascent magma chambers). Complex sill-network intrusion in basin settings can have significant impact on subsurface fluid flow (e.g., water aquifer and hydrocarbon systems), geothermal systems, the maturation of hydrocarbons, and methane release. Models for these effects are critically dependent on the models for sill emplacement. This study focuses on staircase-geometry sills in the Faroe Islands, on the European Atlantic Margin, which are hosted in mechanically layered lavas (1-20 m thick) and basaltic volcaniclastic units (1-30 m thick). The sills range from 20-50 m thick, with each covering ~17 km2, and transgressing a vertical range of ~480 m. Steps in the sills are elliptical in cross section, and discontinuous laterally, forming smooth transgressive ramps, hence are interpreted as representing initial stages of sill propagation as magma fingers, which inflate through time to create a through-going sheet. Although steps correspond to the position of some host rock layer interfaces and volcaniclastic horizons, most interfaces are bypassed. The overall geometry of the sills is consistent with ENE-WSW compression, and NNW-SSE extension, and stress anisotropy-induced transgression. Local morphology indicates that mechanical layering suppressed tensile stress ahead of the crack tip, leading to a switch in minimum and intermediate stress axes, facilitating lateral sill propagation as fingers, and resulting in a stepped transgressive geometry.

Land management practices to become important as biofuels use grows |

Science.gov Websites

Media Photos Videos Fact Sheets, Brochures and Reports Summer Science Writing Internship Land management , making land management practices increasingly important, especially under a scenario where cellulosic impact of agricultural land use and management on U.S. carbon budgets," recently published in the

Basic Drafting: Book One.

ERIC Educational Resources Information Center

Davis, Ronald; And Others

The first of a two-book course in drafting, this manual consists of 13 topics in the following units: introduction to drafting, general safety, basic tools and lines, major equipment, applying for a job, media, lettering, reproduction, drawing sheet layout, architect's scale usage, civil engineer's scale usage, mechanical engineer's scale usage,…

Are you Scared Yet?

PubMed Central

Emery, Sherry L.; Szczypka, Glen; Abril, Eulàlia Puig; Kim, Yoonsang; Vera, Lisa

2014-01-01

In March 2012, the CDC launched “Tips from Former Smokers,” a $54 million national campaign featuring individuals experiencing long-term health consequences of smoking. The campaign approach was based on strong evidence that anti-tobacco ads portraying fear, graphic images, and personal testimonials are associated with attitudinal and behavior change. Yet it was also controversial; critics cited the danger that viewers might reject such intensely graphic messages. Tasked with informing this debate, our study analyzes the corpus of Tips campaign-related tweets obtained via the Twitter Firehose. We provide a novel and rigorous method for media campaign evaluation within the framework of the Extended Parallel Process Model. Among the relevant Tweets, 87% showed evidence of message acceptance, while 7% exhibited message rejection. PMID:25429162

Fabrication and characterization of cylindrical light diffusers comprised of shape memory polymer.

PubMed

Small, Ward; Buckley, Patrick R; Wilson, Thomas S; Loge, Jeffrey M; Maitland, Kristen D; Maitland, Duncan J

2008-01-01

We developed a technique for constructing light diffusing devices comprised of a flexible shape memory polymer (SMP) cylindrical diffuser attached to the tip of an optical fiber. The devices are fabricated by casting an SMP rod over the cleaved tip of an optical fiber and media blasting the SMP rod to create a light diffusing surface. The axial and polar emission profiles and circumferential (azimuthal) uniformity are characterized for various blasting pressures, nozzle-to-sample distances, and nozzle translation speeds. The diffusers are generally strongly forward-directed and consistently withstand over 8 W of incident IR laser light without suffering damage when immersed in water. These devices are suitable for various endoluminal and interstitial biomedical applications.

Fabrication and characterization of cylindrical light diffusers comprised of shape memory polymer

PubMed Central

Small, Ward; Buckley, Patrick R.; Wilson, Thomas S.; Loge, Jeffrey M.; Maitland, Kristen D.; Maitland, Duncan J.

2009-01-01

We developed a technique for constructing light diffusing devices comprised of a flexible shape memory polymer (SMP) cylindrical diffuser attached to the tip of an optical fiber. The devices are fabricated by casting an SMP rod over the cleaved tip of an optical fiber and media blasting the SMP rod to create a light diffusing surface. The axial and polar emission profiles and circumferential (azimuthal) uniformity are characterized for various blasting pressures, nozzle-to-sample distances, and nozzle translation speeds. The diffusers are generally strongly forward-directed and consistently withstand over 8 W of incident IR laser light without suffering damage when immersed in water. These devices are suitable for various endoluminal and interstitial biomedical applications. PMID:18465981

Wrinkling of a thin circular sheet bonded to a spherical substrate

PubMed Central

Kohn, Robert V.

2017-01-01

We consider a disc-shaped thin elastic sheet bonded to a compliant sphere. (Our sheet can slip along the sphere; the bonding controls only its normal displacement.) If the bonding is stiff (but not too stiff), the geometry of the sphere makes the sheet wrinkle to avoid azimuthal compression. The total energy of this system is the elastic energy of the sheet plus a (Winkler-type) substrate energy. Treating the thickness of the sheet h as a small parameter, we determine the leading-order behaviour of the energy as h tends to zero, and we give (almost matching) upper and lower bounds for the next-order correction. Our analysis of the leading-order behaviour determines the macroscopic deformation of the sheet; in particular, it determines the extent of the wrinkled region, and predicts the (non-trivial) radial strain of the sheet. The leading-order behaviour also provides insight about the length scale of the wrinkling, showing that it must be approximately independent of the distance r from the centre of the sheet (so that the number of wrinkles must increase with r). Our results on the next-order correction provide insight about how the wrinkling pattern should vary with r. Roughly speaking, they suggest that the length scale of wrinkling should not be exactly constant—rather, it should vary slightly, so that the number of wrinkles at radius r can be approximately piecewise constant in its dependence on r, taking values that are integer multiples of h−a with . This article is part of the themed issue ‘Patterning through instabilities in complex media: theory and applications’. PMID:28373380

How cracks are hot and cool: a burning issue for paper.

PubMed

Toussaint, Renaud; Lengliné, Olivier; Santucci, Stéphane; Vincent-Dospital, Tom; Naert-Guillot, Muriel; Måløy, Knut Jørgen

2016-07-07

Material failure is accompanied by important heat exchange, with extremely high temperature - thousands of degrees - reached at crack tips. Such a temperature may subsequently alter the mechanical properties of stressed solids, and finally facilitate their rupture. Thermal runaway weakening processes could indeed explain stick-slip motions and even be responsible for deep earthquakes. Therefore, to better understand catastrophic rupture events, it appears crucial to establish an accurate energy budget of fracture propagation from a clear measure of various energy dissipation sources. In this work, combining analytical calculations and numerical simulations, we directly relate the temperature field around a moving crack tip to the part α of mechanical energy converted into heat. By monitoring the slow crack growth in paper sheets using an infrared camera, we measure a significant fraction α = 12% ± 4%. Besides, we show that (self-generated) heat accumulation could weaken our samples by microfiber combustion, and lead to a fast crack/dynamic failure/regime.

Low-temperature, ultrahigh-vacuum tip-enhanced Raman spectroscopy combined with molecular beam epitaxy for in situ two-dimensional materials' studies

NASA Astrophysics Data System (ADS)

Sheng, Shaoxiang; Li, Wenbin; Gou, Jian; Cheng, Peng; Chen, Lan; Wu, Kehui

2018-05-01

Tip-enhanced Raman spectroscopy (TERS), which combines scanning probe microscopy with the Raman spectroscopy, is capable to access the local structure and chemical information simultaneously. However, the application of ambient TERS is limited by the unstable and poorly controllable experimental conditions. Here, we designed a high performance TERS system based on a low-temperature ultrahigh-vacuum scanning tunneling microscope (LT-UHV-STM) and combined with a molecular beam epitaxy (MBE) system. It can be used for growing two-dimensional (2D) materials and for in situ STM and TERS characterization. Using a 2D silicene sheet on the Ag(111) surface as a model system, we achieved an unprecedented 109 Raman single enhancement factor in combination with a TERS spatial resolution down to 0.5 nm. The results show that TERS combined with a MBE system can be a powerful tool to study low dimensional materials and surface science.

A high-sensitive static vector magnetometer based on two vibrating coils

NASA Astrophysics Data System (ADS)

Yin, Jing; Pan, Cheng Liang; Wang, Hong Bo; Feng, Zhi Hua

2011-12-01

A static vector magnetometer based on two-dimensional (2D) vibrating coils actuated by a piezoelectric cantilever is presented. Two individual sensing coils are orthogonally fastened at the tip of cantilever and piezoelectric sheets are used to excite the cantilever bending. Due to off-axis coupler on the tip, the cantilever generates bending and twisting vibrations simultaneously on their corresponding resonant frequencies, realizing the 2D rotating vibrations of the coils. According to Faraday-Lenz Law, output voltages are induced from the coils. They are amplified by a pre-amplifier circuit, decoupled by a phase-sensitive detector, and finally used to calculate the vector of magnetic field at the coil location. The coil head of a prototype magnetometer possesses a dc sensitivity of around 10 μV/Gs with a good linearity in the measuring range from 0 to 16 μT. The corresponding noise level is about 13.1 nT in the bandwidth from 0.01 Hz to 1 Hz.

A tipping point in refreezing accelerates mass loss of Greenland's glaciers and ice caps

NASA Astrophysics Data System (ADS)

Noël, B.; van de Berg, W. J.; Lhermitte, S.; Wouters, B.; Machguth, H.; Howat, I.; Citterio, M.; Moholdt, G.; Lenaerts, J. T. M.; van den Broeke, M. R.

2017-03-01

Melting of the Greenland ice sheet (GrIS) and its peripheral glaciers and ice caps (GICs) contributes about 43% to contemporary sea level rise. While patterns of GrIS mass loss are well studied, the spatial and temporal evolution of GICs mass loss and the acting processes have remained unclear. Here we use a novel, 1 km surface mass balance product, evaluated against in situ and remote sensing data, to identify 1997 (+/-5 years) as a tipping point for GICs mass balance. That year marks the onset of a rapid deterioration in the capacity of the GICs firn to refreeze meltwater. Consequently, GICs runoff increases 65% faster than meltwater production, tripling the post-1997 mass loss to 36+/-16 Gt-1, or ~14% of the Greenland total. In sharp contrast, the extensive inland firn of the GrIS retains most of its refreezing capacity for now, buffering 22% of the increased meltwater production. This underlines the very different response of the GICs and GrIS to atmospheric warming.

Twelve tips for using Twitter as a learning tool in medical education.

PubMed

Forgie, Sarah Edith; Duff, Jon P; Ross, Shelley

2013-01-01

Twitter is an online social networking service, accessible from any Internet-capable device. While other social networking sites are online confessionals or portfolios of personal current events, Twitter is designed and used as a vehicle to converse and share ideas. For this reason, we believe that Twitter may be the most likely candidate for integrating social networking with medical education. Using current research in medical education, motivation and the use of social media in higher education, we aim to show the ways Twitter may be used as a learning tool in medical education. A literature search of several databases, online sources and blogs was carried out examining the use of Twitter in higher education. We created 12 tips for using Twitter as a learning tool and organized them into: the mechanics of using Twitter, suggestions and evidence for incorporating Twitter into many medical education contexts, and promoting research into the use of Twitter in medical education. Twitter is a relatively new social medium, and its use in higher education is in its infancy. With further research and thoughtful application of media literacy, Twitter is likely to become a useful adjunct for more personalized teaching and learning in medical education.

Key findings on legal and regulatory barriers to HIV testing and access to care across Europe.

PubMed

Power, L; Hows, J; Jakobsen, S F

2018-02-01

The aim of this work within OptTEST by HiE has been to demonstrate the role of legal and regulatory barriers in hindering access to HIV testing, treatment and care across Europe and to produce tools to help dismantle them. An online survey to assess country-specific data on legal and regulatory barriers distributed widely across the WHO Europe region. Literature reviews conducted in January-October 2015 in English, in November 2015 in Russian, and updated in April 2017. Semi-structured interviews were conducted with 25 key actors within the HIV field to feed into case studies and tip sheets on how to dismantle legal and regulatory barriers. More than 160 individuals and organisations from 49 countries across the WHO European region provided responses which were analysed and cross checked with other data sources and a searchable database produced (legalbarriers.peoplewithhiveurope.org). The conducted literature reviews yielded 88 papers and reports which identify legal and regulatory barriers to key populations' access to HV testing and care. Based on the interviews with key actors, ranging from PLHIV activists to government officials, on lessons-learned, a series of tip sheets and ten case studies were written-up intended to inform and inspire the HIV community to address and overcome existing barriers (opttest.eu/Tools). While some of the barriers identified may require major changes to wider health systems, or long term legal reform, many are open to a simple change in regulations or custom and practice. We have the tools. Why can't we finish the job? © 2018 British HIV Association.

Unveiling climate and ice-sheet history from drilling in high-latitude margins and future perspectives

NASA Astrophysics Data System (ADS)

Escutia Dotti, Carlota

2010-05-01

Polar ice is an important component of the climate system, affecting global sea level, ocean circulation and heat transport, marine productivity, and albedo. During the last decades drilling in the Arctic (IODP ACEX and Bering Expeditions) and in Antarctica (ODP Legs 178, 188, IODP Expedition 318 and ANDRILL) has revealed regional information about sea ice and ice sheets development and evolution. Integration of this data with numerical modeling provide an understanding of the early development of the ice sheets and their variability through the Cenozoic. Much of this work points to atmospheric CO2 and other greenhouse gases concentrations as important triggering mechanism driving the onset of glaciation and subsequent ice volume variability. With current increasing atmospheric greenhouse gases concentrations resulting in rapidly rising global temperatures, studies of polar climates become increasingly prominent on the research agenda. Despite of the relevance of the high-latitudes in the global climate systems, the short- and long-term history of the ice sheets and sea-ice and its relationships with paleoclimatic, paleoceanographic, and sea level changes is still poorly understood. A multinational, multiplatform scientific drilling strategy is being developed to recover key physical evidence from selected high-latitude areas. This strategy is aimed at addressing key knowledge gaps about the role of polar ice in climate change, targeting questions such as timing of events, rates of change, tipping points, regional variations, and northern vs. southern hemispheres (in phase or out-of-phase) variability. This data is critical to provide constrains to sea-ice and ice sheet models, which are the basis for forecasting the future of the cryosphere in a warming world.

In vitro fabrication of functional three-dimensional tissues with perfusable blood vessels

PubMed Central

Sekine, Hidekazu; Shimizu, Tatsuya; Sakaguchi, Katsuhisa; Dobashi, Izumi; Wada, Masanori; Yamato, Masayuki; Kobayashi, Eiji; Umezu, Mitsuo; Okano, Teruo

2013-01-01

In vitro fabrication of functional vascularized three-dimensional tissues has been a long-standing objective in the field of tissue engineering. Here we report a technique to engineer cardiac tissues with perfusable blood vessels in vitro. Using resected tissue with a connectable artery and vein as a vascular bed, we overlay triple-layer cardiac cell sheets produced from coculture with endothelial cells, and support the tissue construct with media perfused in a bioreactor. We show that endothelial cells connect to capillaries in the vascular bed and form tubular lumens, creating in vitro perfusable blood vessels in the cardiac cell sheets. Thicker engineered tissues can be produced in vitro by overlaying additional triple-layer cell sheets. The vascularized cardiac tissues beat and can be transplanted with blood vessel anastomoses. This technique may create new opportunities for in vitro tissue engineering and has potential therapeutic applications. PMID:23360990

Intercalation of paracetamol into the hydrotalcite-like host

NASA Astrophysics Data System (ADS)

Kovanda, František; Maryšková, Zuzana; Kovář, Petr

2011-12-01

Hydrotalcite-like compounds are often used as host structures for intercalation of various anionic species. The product intercalated with the nonionic, water-soluble pharmaceuticals paracetamol, N-(4-hydroxyphenyl)acetamide, was prepared by rehydration of the Mg-Al mixed oxide obtained by calcination of hydrotalcite-like precursor at 500 °C. The successful intercalation of paracetamol molecules into the interlayer space was confirmed by powder X-ray diffraction and infrared spectroscopy measurements. Molecular simulations showed that the phenolic hydroxyl groups of paracetamol interact with hydroxide sheets of the host via the hydroxyl groups of the positively charged sites of Al-containing octahedra; the interlayer water molecules are located mostly near the hydroxide sheets. The arrangement of paracetamol molecules in the interlayer is rather disordered and interactions between neighboring molecules cause their tilting towards the hydroxide sheets. Dissolution tests in various media showed slower release of paracetamol intercalated in the hydrotalcite-like host in comparison with tablets containing the powdered pharmaceuticals.

Integrating personalized medical test contents with XML and XSL-FO.

PubMed

Toddenroth, Dennis; Dugas, Martin; Frankewitsch, Thomas

2011-03-01

In 2004 the adoption of a modular curriculum at the medical faculty in Muenster led to the introduction of centralized examinations based on multiple-choice questions (MCQs). We report on how organizational challenges of realizing faculty-wide personalized tests were addressed by implementation of a specialized software module to automatically generate test sheets from individual test registrations and MCQ contents. Key steps of the presented method for preparing personalized test sheets are (1) the compilation of relevant item contents and graphical media from a relational database with database queries, (2) the creation of Extensible Markup Language (XML) intermediates, and (3) the transformation into paginated documents. The software module by use of an open source print formatter consistently produced high-quality test sheets, while the blending of vectorized textual contents and pixel graphics resulted in efficient output file sizes. Concomitantly the module permitted an individual randomization of item sequences to prevent illicit collusion. The automatic generation of personalized MCQ test sheets is feasible using freely available open source software libraries, and can be efficiently deployed on a faculty-wide scale.

Pneumatic fractures in confined granular media.

PubMed

Eriksen, Fredrik K; Toussaint, Renaud; Turquet, Antoine L; Måløy, Knut J; Flekkøy, Eirik G

2017-06-01

We perform experiments where air is injected at a constant overpressure P_{in}, ranging from 5 to 250 kPa, into a dry granular medium confined within a horizontal linear Hele-Shaw cell. The setup allows us to explore compacted configurations by preventing decompaction at the outer boundary, i.e., the cell outlet has a semipermeable filter such that beads are stopped while air can pass. We study the emerging patterns and dynamic growth of channels in the granular media due to fluid flow, by analyzing images captured with a high speed camera (1000 images/s). We identify four qualitatively different flow regimes, depending on the imposed overpressure, ranging from no channel formation for P_{in} below 10 kPa, to large thick channels formed by erosion and fingers merging for high P_{in} around 200 kPa. The flow regimes where channels form are characterized by typical finger thickness, final depth into the medium, and growth dynamics. The shape of the finger tips during growth is studied by looking at the finger width w as function of distance d from the tip. The tip profile is found to follow w(d)∝d^{β}, where β=0.68 is a typical value for all experiments, also over time. This indicates a singularity in the curvature d^{2}d/dw^{2}∼κ∼d^{1-2β}, but not of the slope dw/dd∼d^{β-1}, i.e., more rounded tips rather than pointy cusps, as they would be for the case β>1. For increasing P_{in}, the channels generally grow faster and deeper into the medium. We show that the channel length along the flow direction has a linear growth with time initially, followed by a power-law decay of growth velocity with time as the channel approaches its final length. A closer look reveals that the initial growth velocity v_{0} is found to scale with injection pressure as v_{0}∝P_{in}^{3/2}, while at a critical time t_{c} there is a cross-over to the behavior v(t)∝t^{-α}, where α is close to 2.5 for all experiments. Finally, we explore the fractal dimension of the fully developed patterns. For example, for patterns resulting from intermediate P_{in} around 100-150 kPa, we find that the box-counting dimensions lie within the range D_{B}∈[1.53,1.62], similar to viscous fingering fractals in porous media.

Pneumatic fractures in confined granular media

NASA Astrophysics Data System (ADS)

Eriksen, Fredrik K.; Toussaint, Renaud; Turquet, Antoine L.; Mâløy, Knut J.; Flekkøy, Eirik G.

2017-06-01

We perform experiments where air is injected at a constant overpressure Pin, ranging from 5 to 250 kPa, into a dry granular medium confined within a horizontal linear Hele-Shaw cell. The setup allows us to explore compacted configurations by preventing decompaction at the outer boundary, i.e., the cell outlet has a semipermeable filter such that beads are stopped while air can pass. We study the emerging patterns and dynamic growth of channels in the granular media due to fluid flow, by analyzing images captured with a high speed camera (1000 images/s). We identify four qualitatively different flow regimes, depending on the imposed overpressure, ranging from no channel formation for Pin below 10 kPa, to large thick channels formed by erosion and fingers merging for high Pin around 200 kPa. The flow regimes where channels form are characterized by typical finger thickness, final depth into the medium, and growth dynamics. The shape of the finger tips during growth is studied by looking at the finger width w as function of distance d from the tip. The tip profile is found to follow w (d ) ∝dβ , where β =0.68 is a typical value for all experiments, also over time. This indicates a singularity in the curvature d2d /d w2˜κ ˜d1 -2 β , but not of the slope d w /d d ˜dβ -1 , i.e., more rounded tips rather than pointy cusps, as they would be for the case β >1 . For increasing Pin, the channels generally grow faster and deeper into the medium. We show that the channel length along the flow direction has a linear growth with time initially, followed by a power-law decay of growth velocity with time as the channel approaches its final length. A closer look reveals that the initial growth velocity v0 is found to scale with injection pressure as v0∝Pin3/2 , while at a critical time tc there is a cross-over to the behavior v (t ) ∝t-α , where α is close to 2.5 for all experiments. Finally, we explore the fractal dimension of the fully developed patterns. For example, for patterns resulting from intermediate Pin around 100-150 kPa, we find that the box-counting dimensions lie within the range DB∈[1.53 ,1.62 ] , similar to viscous fingering fractals in porous media.

Bridging the divide between science and journalism.

PubMed

Van Eperen, Laura; Marincola, Francesco M; Strohm, Jennifer

2010-03-10

There are countless reasons nearly every scientist should learn how to communicate effectively with the media, including increased understanding of critical research findings to attract or sustain funding and build new professional partnerships that will further propel forward research. But where do scientists begin? Bridging the Divide between Science and Journalism offers practical tips for any scientist looking to work with the media.Given the traditional and internet-based sources for medical research and healthcare-related news now available, it is imperative that scientists know how to communicate their latest findings through the appropriate channels. The credible media channels are managed by working journalists, so learning how to package vast, technical research in a form that is appetizing and "bite-sized" in order to get their attention, is an art. Reducing years of research into a headline can be extremely difficult and certainly doesn't come naturally to every scientist, so this article provides suggestions on how to work with the media to communicate your findings.

Bridging the Divide between Science and Journalism

PubMed Central

2010-01-01

There are countless reasons nearly every scientist should learn how to communicate effectively with the media, including increased understanding of critical research findings to attract or sustain funding and build new professional partnerships that will further propel forward research. But where do scientists begin? Bridging the Divide between Science and Journalism offers practical tips for any scientist looking to work with the media. Given the traditional and internet-based sources for medical research and healthcare-related news now available, it is imperative that scientists know how to communicate their latest findings through the appropriate channels. The credible media channels are managed by working journalists, so learning how to package vast, technical research in a form that is appetizing and "bite-sized" in order to get their attention, is an art. Reducing years of research into a headline can be extremely difficult and certainly doesn't come naturally to every scientist, so this article provides suggestions on how to work with the media to communicate your findings. PMID:20219123

Tie-fibre structure and organization in the knee menisci

PubMed Central

Andrews, Stephen H J; Rattner, Jerome B; Abusara, Ziad; Adesida, Adetola; Shrive, Nigel G; Ronsky, Janet L

2014-01-01

The collagenous structure of the knee menisci is integral to the mechanical integrity of the tissue and the knee joint. The tie-fibre structure of the tissue has largely been neglected, despite previous studies demonstrating its correlation with radial stiffness. This study has evaluated the structure of the tie-fibres of bovine menisci using 2D and 3D microscopy techniques. Standard collagen and proteoglycan (PG) staining and 2D light microscopy techniques were conducted. For the first time, the collagenous structure of the menisci was evaluated using 3D, second harmonic generation (SHG) microscopy. This technique facilitated the imaging of collagen structure in thick sections (50–100 μm). Imaging identified that tie-fibres of the menisci arborize from the outer margin of the meniscus toward the inner tip. This arborization is associated with the structural arrangement of the circumferential fibres. SHG microscopy has definitively demonstrated the 3D organization of tie-fibres in both sheets and bundles. The hierarchy of the structure is related to the organization of circumferential fascicles. Large tie-fibre sheets bifurcate into smaller sheets to surround circumferential fascicles of decreasing size. The tie-fibres emanate from the lamellar layer that appears to surround the entire meniscus. At the tibial and femoral surfaces these tie-fibre sheets branch perpendicularly into the meniscal body. The relationship between tie-fibres and blood vessels in the menisci was also observed in this study. Tie-fibre sheets surround the blood vessels and an associated PG-rich region. This subunit of the menisci has not previously been described. The size of tie-fibre sheets surrounding the vessels appeared to be associated with the size of blood vessel. These structural findings have implications in understanding the mechanics of the menisci. Further, refinement of the complex structure of the tie-fibres is important in understanding the consequences of injury and disease in the menisci. The framework of meniscus architecture also defines benchmarks for the development of tissue-engineered replacements in the future. PMID:24617800

Cavitation noise studies on marine propellers

NASA Astrophysics Data System (ADS)

Sharma, S. D.; Mani, K.; Arakeri, V. H.

1990-04-01

Experimental observations are described of cavitation inception and noise from five model propellers, three basic and two modified, tested in the open jet section of the Indian Institute of Science high-speed water tunnel facility. Extensive experiments on the three basic propellers of different design, which included visualization of cavitation and measurements of noise, showed that the dominant type of cavitation was in the form of tip vortex cavitation, accompanied by leading edge suction side sheet cavitation in its close vicinity, and the resultant noise depended on parameters such as the advance coefficient, the cavitation number, and the propeller geometry. Of these, advance coefficient was found to have the maximum influence not only on cavitation noise but also on the inception of cavitation. Noise levels and frequencies of spectra obtained from all the three basic propellers at conditions near inception and different advance coefficient values, when plotted in the normalized form as suggested by Blake, resulted in a universal spectrum which would be useful for predicting cavitation noise at prototype scales when a limited extent of cavitation is expected in the same form as observed on the present models. In an attempt to delay the onset of tip vortex cavitation, the blades of two of the three basic propellers were modified by drilling small holes in the tip and leading edge areas. Studies on the modified propellers showed that the effectiveness of the blade modification was apparently stronger at low advance coefficient values and depended on the blade sectional profile. Measurements of cavitation noise indicated that the modification also improved the acoustic performance of the propellers as it resulted in a complete attenuation of the low-frequency spectral peaks, which were prominent with the basic propellers. In addition to the above studies, which were conducted under uniform flow conditions, one of the basic propellers was tested in the simulated wake of a typical single screw ship. The wake was simulated by using a wire screen technique. Observations of cavitation and measurement of noise clearly showed that the presence of the wake had a strong influence on the propeller cavitation and noise performance. Cavitation was found to be of the cloud type, which generated very intense noise compared to that generated by tip vortex cavitation along with leading edge suction side sheet cavitation in the uniform flow conditions. The noise spectra obtained with wake simulation also are presented in a normalized form to be of general utility.

Drying of fiber webs

DOEpatents

Warren, David W.

1997-01-01

A process and an apparatus for high-intensity drying of fiber webs or sheets, such as newsprint, printing and writing papers, packaging paper, and paperboard or linerboard, as they are formed on a paper machine. The invention uses direct contact between the wet fiber web or sheet and various molten heat transfer fluids, such as liquified eutectic metal alloys, to impart heat at high rates over prolonged durations, in order to achieve ambient boiling of moisture contained within the web. The molten fluid contact process causes steam vapor to emanate from the web surface, without dilution by ambient air; and it is differentiated from the evaporative drying techniques of the prior industrial art, which depend on the uses of steam-heated cylinders to supply heat to the paper web surface, and ambient air to carry away moisture, which is evaporated from the web surface. Contact between the wet fiber web and the molten fluid can be accomplished either by submersing the web within a molten bath or by coating the surface of the web with the molten media. Because of the high interfacial surface tension between the molten media and the cellulose fiber comprising the paper web, the molten media does not appreciately stick to the paper after it is dried. Steam generated from the paper web is collected and condensed without dilution by ambient air to allow heat recovery at significantly higher temperature levels than attainable in evaporative dryers.

National Civics Teacher Survey: Information Literacy in High School Civics. Fact Sheet

ERIC Educational Resources Information Center

Kawashima-Ginsberg, Kei

2014-01-01

Teaching students to use news and information media ("information literacy") is an important aspect of civic education, especially now that news sources are rapidly changing and fragmenting along ideological lines. Information literacy is required in several state standards, and it is also frequently defined as an important "21st…

White Control and Minority Oppression. Fact Sheets on Institutional Racism.

ERIC Educational Resources Information Center

Foundation for Change, Inc., New York, NY.

Salient facts about white control and minority oppression are provided for major areas such as the economy, health, housing, education, the media, government, and the census. Economic data on white control cover topics such as wealth, the stock exchange, businesses, banks, union control and membership, and others. Data per training to minority…

Male Control and Female Oppression. Fact Sheets on Institutional Racism.

ERIC Educational Resources Information Center

Foundation for Change, Inc., New York, NY.

Following sections that define sexism, that give examples of individual, cultural, and institutional sexism, and that provide random thoughts on sexism and racism, statistics are listed for women and their relationship to various areas such as the economy, education, sports, the government, the media, and housing. Specific topics subsumed under…

Fermilab Library

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Big Bang. Featured New eBooks The Black Book of Quantum Chromodynamics This book by Fermilab author at the LHC This book aims to give a broad organizational and strategic understanding of the nature of

ASK A Scientist | News

Science.gov Websites

Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and brochures Media Scientist June 3, 2018, 1:00 pm Fermilab news Search Upcoming events May 27 Sun English Country Dancing Kuhn Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For Industry

Practical experience with full-scale structured sheet media (SSM) integrated fixed-film activated sludge (IFAS) systems for nitrification.

PubMed

Li, Hua; Zhu, Jia; Flamming, James J; O'Connell, Jack; Shrader, Michael

2015-01-01

Many wastewater treatment plants in the USA, which were originally designed as secondary treatment systems with no or partial nitrification requirements, are facing increased flows, loads, and more stringent ammonia discharge limits. Plant expansion is often not cost-effective due to either high construction costs or lack of land. Under these circumstances, integrated fixed-film activated sludge (IFAS) systems using both suspended growth and biofilms that grow attached to a fixed plastic structured sheet media are found to be a viable solution for solving the challenges. Multiple plants have been retrofitted with such IFAS systems in the past few years. The system has proven to be efficient and reliable in achieving not only consistent nitrification, but also enhanced bio-chemical oxygen demand removal and sludge settling characteristics. This paper presents long-term practical experiences with the IFAS system design, operation and maintenance, and performance for three full-scale plants with distinct processes; that is, a trickling filter/solids contact process, a conventional plug flow activated sludge process and an extended aeration process.

The influence of the environment on the propagation of protostellar outflows

NASA Astrophysics Data System (ADS)

Moraghan, Anthony; Smith, Michael D.; Rosen, Alexander

2008-06-01

The properties of bipolar outflows depend on the structure in the environment as well as the nature of the jet. To help distinguish between the two, we investigate here the properties pertaining to the ambient medium. We execute axisymmetric hydrodynamic simulations, injecting continuous atomic jets into molecular media with density gradients (protostellar cores) and density discontinuities (thick swept-up sheets). We determine the distribution of outflowing mass with radial velocity (the mass spectrum) to quantify our approach and to compare to observationally determined values. We uncover a sequence from clump entrainment in the flanks to bow shock sweeping as the density profile steepens. We also find that the dense, highly supersonic outflows remain collimated but can become turbulent after passing through a shell. The mass spectra vary substantially in time, especially at radial speeds exceeding 15 kms-1. The mass spectra also vary according to the conditions: both envelope-type density distributions and the passage through dense sheets generate considerably steeper mass spectra than a uniform medium. The simulations suggest that observed outflows penetrate highly non-uniform media.

Separation of ballistic and diffusive fluorescence photons in confocal Light-Sheet Microscopy of Arabidopsis roots.

PubMed

Meinert, Tobias; Tietz, Olaf; Palme, Klaus J; Rohrbach, Alexander

2016-08-24

Image quality in light-sheet fluorescence microscopy is strongly affected by the shape of the illuminating laser beam inside embryos, plants or tissue. While the phase of Gaussian or Bessel beams propagating through thousands of cells can be partly controlled holographically, the propagation of fluorescence light to the detector is difficult to control. With each scatter process a fluorescence photon loses information necessary for the image generation. Using Arabidopsis root tips we demonstrate that ballistic and diffusive fluorescence photons can be separated by analyzing the image spectra in each plane without a priori knowledge. We introduce a theoretical model allowing to extract typical scattering parameters of the biological material. This allows to attenuate image contributions from diffusive photons and to amplify the relevant image contributions from ballistic photons through a depth dependent deconvolution. In consequence, image contrast and resolution are significantly increased and scattering artefacts are minimized especially for Bessel beams with confocal line detection.

Separation of ballistic and diffusive fluorescence photons in confocal Light-Sheet Microscopy of Arabidopsis roots

PubMed Central

Meinert, Tobias; Tietz, Olaf; Palme, Klaus J.; Rohrbach, Alexander

2016-01-01

Image quality in light-sheet fluorescence microscopy is strongly affected by the shape of the illuminating laser beam inside embryos, plants or tissue. While the phase of Gaussian or Bessel beams propagating through thousands of cells can be partly controlled holographically, the propagation of fluorescence light to the detector is difficult to control. With each scatter process a fluorescence photon loses information necessary for the image generation. Using Arabidopsis root tips we demonstrate that ballistic and diffusive fluorescence photons can be separated by analyzing the image spectra in each plane without a priori knowledge. We introduce a theoretical model allowing to extract typical scattering parameters of the biological material. This allows to attenuate image contributions from diffusive photons and to amplify the relevant image contributions from ballistic photons through a depth dependent deconvolution. In consequence, image contrast and resolution are significantly increased and scattering artefacts are minimized especially for Bessel beams with confocal line detection. PMID:27553506

Needle Tip Position and Bevel Direction Have No Effect in the Fluoroscopic Epidural Spreading Pattern in Caudal Epidural Injections: A Randomized Trial

PubMed Central

Kwon, Won Kyoung; Kim, Ah Na; Lee, Pil Moo; Park, Cheol Hwan; Kim, Jae Hun

2016-01-01

Background. Caudal epidural steroid injections (CESIs) are an effective treatment for pain. If the injection spreads in a specific pattern depending on the needle position or bevel direction, it would be possible to inject the agent into a specific and desired area. Objectives. We conducted a prospective randomized trial to determine if the needle position and bevel direction have any effect on the epidural spreading pattern in CESI. Methods. Demographic data of the patient were collected. During CESI, the needle position (middle or lateral) and direction (ventral or dorsal) were randomly allocated. Following fluoroscope-guided injection of 4 mL contrast media and 10 mL of injectates, the epidural spreading patterns (ventral or dorsal, bilateral or lateral) were imaged. Results. In the 210 CESIs performed, the needle tip position and bevel direction did not influence the epidural spreading patterns at L4-5 and L5-S1 disc levels. A history of Lumbar spine surgery was associated with a significantly limited spread to each disc level. A midline needle tip position was more effective than the lateral position in spreading to the distant disc levels. Conclusions. Neither the needle tip position nor the bevel direction affected the epidural drug spreading pattern during CESI. PMID:27445609

Mass-velocity and size-velocity distributions of ejecta cloud from shock-loaded tin surface using large scale molecular dynamics simulations

NASA Astrophysics Data System (ADS)

Durand, Olivier; Soulard, Laurent

2015-06-01

The mass (volume and areal densities) versus velocity as well as the size versus velocity distributions of a shock-induced cloud of particles are investigated using large scale molecular dynamics (MD) simulations. A generic 3D tin crystal with a sinusoidal free surface roughness is set in contact with vacuum and shock-loaded so that it melts directly on shock. At the reflection of the shock wave onto the perturbations of the free surface, 2D sheets/jets of liquid metal are ejected. The simulations show that the distributions may be described by an analytical model based on the propagation of a fragmentation zone, from the tip of the sheets to the free surface, within which the kinetic energy of the atoms decreases as this zone comes closer to the free surface on late times. As this kinetic energy drives (i) the (self-similar) expansion of the zone once it has broken away from the sheet and (ii) the average size of the particles which result from fragmentation in the zone, the ejected mass and the average size of the particles progressively increase in the cloud as fragmentation occurs closer to the free surface. Though relative to nanometric scales, our model reproduces quantitatively experimental profiles and may help in their analysis.

Three-dimensional real-time imaging of bi-phasic flow through porous media

NASA Astrophysics Data System (ADS)

Sharma, Prerna; Aswathi, P.; Sane, Anit; Ghosh, Shankar; Bhattacharya, S.

2011-11-01

We present a scanning laser-sheet video imaging technique to image bi-phasic flow in three-dimensional porous media in real time with pore-scale spatial resolution, i.e., 35 μm and 500 μm for directions parallel and perpendicular to the flow, respectively. The technique is illustrated for the case of viscous fingering. Using suitable image processing protocols, both the morphology and the movement of the two-fluid interface, were quantitatively estimated. Furthermore, a macroscopic parameter such as the displacement efficiency obtained from a microscopic (pore-scale) analysis demonstrates the versatility and usefulness of the method.

In vitro regeneration of solanum aethiopicum L. (scarlet eggplant), an african vegetable crop with potential ornamental value

USDA-ARS?s Scientific Manuscript database

Successful in vitro regeneration of plantlets was obtained from shoot tips of five Solanum aethiopicum (African eggplants) accessions evaluated in two media, M1 and M2. The M1 medium consisted of Murashige and Skoog (MS) basal salt mixture supplemented with 20 g/L sucrose, 0.75 g/L MgCl2, and 2 g/L ...

Tipping news in information accumulation system

NASA Astrophysics Data System (ADS)

Shin, J. K.

2010-05-01

As a continuous opinion dynamics model, the information accumulation system (IAS) includes three basic mechanisms of the news, the inheritance and the diffusion as contributing to the information accumulation process of a system. A system is composed of agents who diffuse information through internal interaction, while each of them has incomplete memory or inheritance rate. The news comes from external sources of information, such as mass media. Previously the model IAS was studied only for the small news problems. In this study, a tipping news problem is considered. A key question of the problem is: what is the minimum strength of advertisement that can tip the minority opinion to a majority one? Dynamics of the IAS is briefly revisited with a special interest on nonlinear behavior of the model. In particular, it is shown that a discrete map of the IAS for a single color problem can be transformed into a logistic map, from which the dynamics of the IAS can be better understood. To show the applicability of the IAS model, the result is applied to explain the concept of the critical population size, which claims that there is a minimum population size for a social knowledge system to be continuously inherited without being lost. And critical size of the tipping news is found analytically in terms of IAS parameters. Some of the key results from the present study are compared in detail with the results from the Brownian particle model, which is believed to be the most similar model to the IAS. The concept of tipping news is used to show that a traditional society can tip at an exceptionally low inter-community exposure. Finally, the result was applied to the language competition problem.

INTERDISCIPLINARY PHYSICS AND RELATED AREAS OF SCIENCE AND TECHNOLOGY: Multi-mode Spiral Wave in a Coupled Oscillatory Medium

NASA Astrophysics Data System (ADS)

Wang, Qun; Gao, Qing-Yu; Lü, Hua-Ping; Zheng, Zhi-Gang

2010-05-01

Multi-mode spiral wave and its breakup in 1-d and 2-d coupled oscillatory media is studied here by theoretic analysis and numerical simulations. The analysis in 1-d system shows that the dispersion relation curve could be non-monotonic depending on the coupling strength. It may also lead to the coexistence of different wave numbers within one system. Direct numerical observations in 1-d and 2-d systems conform to the prediction of dispersion relation analysis. Our findings indicate that the wave grouping can also be observed in oscillatory media without tip meandering and waves with negative group velocity can occur without inhomogeneity.

Main factors causing intergranular and quasi-cleavage fractures at hydrogen-induced cracking in tempered martensitic steels

NASA Astrophysics Data System (ADS)

Kurokawa, Ami; Doshida, Tomoki; Hagihara, Yukito; Suzuki, Hiroshi; Takai, Kenichi

2018-05-01

Though intergranular (IG) and quasi-cleavage (QC) fractures have been widely recognized as typical fracture modes of the hydrogen-induced cracking in high-strength steels, the main factor has been unclarified yet. In the present study, the hydrogen content dependence on the main factor causing hydrogen-induced cracking has been examined through the fracture mode transition from QC to IG at the crack initiation site in the tempered martensitic steels. Two kinds of tempered martensitic steels were prepared to change the cohesive force due to the different precipitation states of Fe3C on the prior γ grain boundaries. A high amount of Si (H-Si) steel has a small amount of Fe3C on the prior austenite grain boundaries. Whereas, a low amount of Si (L-Si) steel has a large amount of Fe3C sheets on the grain boundaries. The fracture modes and initiations were observed using FE-SEM (Field Emission-Scanning Electron Microscope). The crack initiation sites of the H-Si steel were QC fracture at the notch tip under various hydrogen contents. While the crack initiation of the L-Si steel change from QC fracture at the notch tip to QC and IG fractures from approximately 10 µm ahead of the notch tip as increasing in hydrogen content. For L-Si steels, two possibilities are considered that the QC or IG fracture occurred firstly, or the QC and IG fractures occurred simultaneously. Furthermore, the principal stress and equivalent plastic strain distributions near the notch tip were calculated with FEM (Finite Element Method) analysis. The plastic strain was the maximum at the notch tip and the principle stress was the maximum at approximately 10 µm from the notch tip. The position of the initiation of QC and IG fracture observed using FE-SEM corresponds to the position of maximum strain and stress obtained with FEM, respectively. These findings indicate that the main factors causing hydrogen-induced cracking are different between QC and IG fractures.

Using IRI and GSM TIP model results as environment for HF radio wave propagation model during the geomagnetic storm occurred on September 26-29, 2011

NASA Astrophysics Data System (ADS)

Kotova, D. S.; Klimenko, M. V.; Klimenko, V. V.; Zakharov, V. E.; Ratovsky, K. G.; Nosikov, I. A.; Zhao, B.

2015-11-01

This paper analyses the geomagnetic storm on September 26-29, 2011. We compare the calculation results obtained using the Global Self-consistent Model of the Thermosphere, Ionosphere and Protonosphere (GSM TIP) and IRI-2012 (Bilitza et al., 2014) model with ground-based ionosonde data of stations at different latitudes and longitudes. We examined physical mechanisms responsible for the formation of ionospheric effects during the main phase of geomagnetic storm that occurred at the rising phase of the 24th solar cycle. We used numerical results obtained from IRI-2012 and GSM TIP models as propagation environment for HF signals from an equatorial transmitter during quiet and disturbed conditions. We used the model of HF radio wave propagation developed in I. Kant Baltic Federal University (BFU) that is based on the geometrical optics approximation. We compared the obtained radio paths in quiet conditions and during the main and recovery storm phases and evaluated radio wave attenuation in different media models.

Remediating Contaminant Plumes in Groundwater with Shallow Excavations Containing Coarse Reactive Media.

PubMed

Hudak, Paul F

2018-02-01

A groundwater flow and mass transport model tested the capability of shallow excavations filled with coarse, reactive media to remediate a hypothetical unconfined aquifer with a maximum saturated thickness of 5 m. Modeled as contaminant sinks, the rectangular excavations were 10 m downgradient of an initial contaminant plume originating from a source at the top of the aquifer. The initial plume was approximately 259 m long, 23 m wide, and 5 m thick, with a downgradient tip located approximately 100 m upgradient of the site boundary. The smallest trench capable of preventing offsite migration was 11 m long (measured perpendicular to groundwater flow), 4 m wide (measured parallel to groundwater flow), and 3 m deep. Results of this study suggest that shallow trenches filled with coarse filter media that partially penetrate unconfined aquifers may be a viable alternative for remediating contaminated groundwater at some sites.

Quantum friction on monoatomic layers and its classical analog

NASA Astrophysics Data System (ADS)

Maslovski, Stanislav I.; Silveirinha, Mário G.

2013-07-01

We consider the effect of quantum friction at zero absolute temperature resulting from polaritonic interactions in closely positioned two-dimensional arrays of polarizable atoms (e.g., graphene sheets) or thin dielectric sheets modeled as such arrays. The arrays move one with respect to another with a nonrelativistic velocity v≪c. We confirm that quantum friction is inevitably related to material dispersion, and that such friction vanishes in nondispersive media. In addition, we consider a classical analog of the quantum friction which allows us to establish a link between the phenomena of quantum friction and classical parametric generation. In particular, we demonstrate how the quasiparticle generation rate typically obtained from the quantum Fermi golden rule can be calculated classically.

Guided magnonic Michelson interferometer

PubMed Central

Ahmed, Muhammad H.; Jeske, Jan; Greentree, Andrew D.

2017-01-01

Magnonics is an emerging field with potential applications in classical and quantum information processing. Freely propagating magnons in two-dimensional media are subject to dispersion, which limits their effective range and utility as information carriers. We show the design of a confining magnonic waveguide created by two surface current carrying wires placed above a spin-sheet, which can be used as a primitive for reconfigurable magnonic circuitry. We theoretically demonstrate the ability of such guides to counter the transverse dispersion of the magnon in a spin-sheet, thus extending the range of the magnon. A design of a magnonic directional coupler and controllable Michelson interferometer is shown, demonstrating its utility for information processing tasks. PMID:28134271

Defense Threat Reduction Agency > Research > DTRIAC > Media Collection

Science.gov Websites

*Cover a broad scope of both the pre- and post-test activities of a test series or operation *Detonations FOIA Electronic Reading Room Privacy Impact Assessment DTRA No Fear Act Reporting Nuclear Test Personnel Review NTPR Fact Sheets NTPR Radiation Dose Assessment Documents US Atmospheric Nuclear Test

Fermilab | Science | Inquiring Minds | The science of matter, space and

Science.gov Websites

Contact Phone Book Newsroom Newsroom News and features Press releases Photo gallery Fact sheets and process For the media Video of shutdown event Guest book Tevatron Impact June 11, 2012 About the symposium Security, Privacy, Legal Use of Cookies Quick Links Home Contact Phone Book Fermilab at Work For Industry

Adapting HYDRUS-1D to simulate overland flow and reactive transport during sheet flow deviations

USDA-ARS?s Scientific Manuscript database

The HYDRUS-1D code is a popular numerical model for solving the Richards equation for variably-saturated water flow and solute transport in porous media. This code was adapted to solve rather than the Richards equation for subsurface flow the diffusion wave equation for overland flow at the soil sur...

Social media for radiologists: an introduction.

PubMed

Ranschaert, Erik R; van Ooijen, P M A; Lee, Simon; Ratib, Osman; Parizel, P M

2015-12-01

Social media, which can be defined as dynamic and interactive online communication forums, are becoming increasingly popular, not only for the general public but also for radiologists. In addition to assisting radiologists in finding useful profession-related information and interactive educational material in all kinds of formats, they can also contribute towards improving communication with peers, clinicians, and patients. The growing use of social networking in healthcare also has an impact on the visibility and engagement of radiologists in the online virtual community. Although many radiologists are already using social media, a large number of our colleagues are still unaware of the wide spectrum of useful information and interaction available via social media and of the added value these platforms can bring to daily practice. For many, the risk of mixing professional and private data by using social media creates a feeling of insecurity, which still keeps radiologists from using them. In this overview we aim to provide information on the potential benefits, challenges, and inherent risks of social media for radiologists. We will provide a summary of the different types of social media that can be of value for radiologists, including useful tips on how to use them safely and efficiently. • Online social networking enhances communication and collaboration between peers • Social media facilitate access to educational and scientific information • Recommendations and guidelines from policymakers and professional organisations are needed • Applications are desired for efficient and secure exchange of medical images in social media.

Twelve tips for using digital storytelling to promote reflective learning by medical students.

PubMed

Sandars, John; Murray, Christopher; Pellow, Andy

2008-01-01

Digital storytelling has potential to motivate students to engage in reflective learning since it uses a range of new technologies and multimedia that are more familiar to young people. The use of visual and audio media offers creative opportunities that can motivate students to develop deeper learning. A structured approach to creating a digital story is essential so that its potential is achieved.

Start Your Search Engines. Part One: Taming Google--and Other Tips to Master Web Searches

ERIC Educational Resources Information Center

Adam, Anna; Mowers, Helen

2008-01-01

There are a lot of useful tools on the Web, all those social applications, and the like. Still most people go online for one thing--to perform a basic search. For most fact-finding missions, the Web is there. But--as media specialists well know--the sheer wealth of online information can hamper efforts to focus on a few reliable references.…

Comparison of the quantitative dry culture methods with both conventional media and most probable number method for the enumeration of coliforms and Escherichia coli/coliforms in food.

PubMed

Teramura, H; Sota, K; Iwasaki, M; Ogihara, H

2017-07-01

Sanita-kun™ CC (coliform count) and EC (Escherichia coli/coliform count), sheet quantitative culture systems which can avoid chromogenic interference by lactase in food, were evaluated in comparison with conventional methods for these bacteria. Based on the results of inclusivity and exclusivity studies using 77 micro-organisms, sensitivity and specificity of both Sanita-kun™ met the criteria for ISO 16140. Both media were compared with deoxycholate agar, violet red bile agar, Merck Chromocult™ coliform agar (CCA), 3M Petrifilm™ CC and EC (PEC) and 3-tube MPN, as reference methods, in 100 naturally contaminated food samples. The correlation coefficients of both Sanita-kun™ for coliform detection were more than 0·95 for all comparisons. For E. coli detection, Sanita-kun™ EC was compared with CCA, PEC and MPN in 100 artificially contaminated food samples. The correlation coefficients for E. coli detection of Sanita-kun™ EC were more than 0·95 for all comparisons. There were no significant differences in all comparisons when conducting a one-way analysis of variance (anova). Both Sanita-kun™ significantly inhibited colour interference by lactase when inhibition of enzymatic staining was assessed using 40 natural cheese samples spiked with coliform. Our results demonstrated Sanita-kun™ CC and EC are suitable alternatives for the enumeration of coliforms and E. coli/coliforms, respectively, in a variety of foods, and specifically in fermented foods. Current chromogenic media for coliforms and Escherichia coli/coliforms have enzymatic coloration due to breaking down of chromogenic substrates by food lactase. The novel sheet culture media which have film layer to avoid coloration by food lactase have been developed for enumeration of coliforms and E. coli/coliforms respectively. In this study, we demonstrated these media had comparable performance with reference methods and less interference by food lactase. These media have a possibility not only to be useful alternatives but also to contribute for accurate enumeration of these bacteria in a variety of foods, and specifically in fermented foods. © 2017 The Society for Applied Microbiology.

Drying of fiber webs

DOEpatents

Warren, D.W.

1997-04-15

A process and an apparatus are disclosed for high-intensity drying of fiber webs or sheets, such as newsprint, printing and writing papers, packaging paper, and paperboard or linerboard, as they are formed on a paper machine. The invention uses direct contact between the wet fiber web or sheet and various molten heat transfer fluids, such as liquefied eutectic metal alloys, to impart heat at high rates over prolonged durations, in order to achieve ambient boiling of moisture contained within the web. The molten fluid contact process causes steam vapor to emanate from the web surface, without dilution by ambient air; and it is differentiated from the evaporative drying techniques of the prior industrial art, which depend on the uses of steam-heated cylinders to supply heat to the paper web surface, and ambient air to carry away moisture, which is evaporated from the web surface. Contact between the wet fiber web and the molten fluid can be accomplished either by submersing the web within a molten bath or by coating the surface of the web with the molten media. Because of the high interfacial surface tension between the molten media and the cellulose fiber comprising the paper web, the molten media does not appreciatively stick to the paper after it is dried. Steam generated from the paper web is collected and condensed without dilution by ambient air to allow heat recovery at significantly higher temperature levels than attainable in evaporative dryers. 6 figs.

Alloy 33: A new material for the handling of HNO{sub 3}/HF media in reprocessing of nuclear fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koehler, M.; Heubner, U.; Eichenhofer, K.W.

Alloy 33, an austenitic 33Cr-32Fe-31Ni-1.6Mo-0.6Cu-0.4N material shows excellent resistance to corrosion when exposed to highly oxidizing media as e.g. HNO{sub 3} and HNO{sub 3}/HF mixtures which are encountered in reprocessing of nuclear fuel. According to the test results available so far, resistance to corrosion in boiling azeotropic (67%) HNO{sub 3} is about 6 and 2 times superior to AISI 304 L and 310 L. In higher concentrated nitric acid it can be considered corrosion resistant up to 95% HNO{sub 3} at 25 C, up to 90% HNO{sub 3} at 50 C and up to somewhat less than 85% HNO{sub 3}more » at 75 C. In 20% HNO{sub 3}/7% HF at 50 C its resistance to corrosion is superior to AISI 316 Ti and Alloy 28 by factors of about 200 and 2.4. Other media tested with different results include 12% HNO{sub 3} with up to 3.5% HF and 0.4% HF with 32 to 67.5% HNO{sub 3} at 90 C. Alloy 33 is easily fabricated into all product forms required for chemical plants (e.g. plate, sheet, strip, wire, tube and flanges). Components such as dished ends and tube to tube sheet weldments have been successfully fabricated facilitating the use of Alloy 33 for reprocessing of nuclear fuel.« less

Swimming & Propulsion in Viscoelastic Media

NASA Astrophysics Data System (ADS)

Arratia, Paulo

2012-02-01

Many microorganisms have evolved within complex fluids, which include soil, intestinal fluid, and mucus. The material properties or rheology of such fluids can strongly affect an organism's swimming behavior. A major challenge is to understand the mechanism of propulsion in media that exhibit both solid- and fluid-like behavior, such as viscoelastic fluids. In this talk, we present experiments that explore the swimming behavior of biological organisms and artificial particles in viscoelastic media. The organism is the nematode Caenorhabditis elegans, a roundworm widely used for biological research that swims by generating traveling waves along its body. Overall, we find that fluid elasticity hinders self-propulsion compared to Newtonian fluids due to the enhanced resistance to flow near hyperbolic points for viscoelastic fluids. As fluid elasticity increases, the nematode's propulsion speed decreases. These results are consistent with recent theoretical models for undulating sheets and cylinders. In order to gain further understanding on propulsion in viscoelastic media, we perform experiments with simple reciprocal artificial `swimmers' (magnetic dumbbell particles) in polymeric and micellar solutions. We find that self-propulsion is possible in viscoelastic media even if the motion is reciprocal.

A combined Surface Enhanced Raman Spectroscopy (SERS)/UV-vis approach for the investigation of dye content in commercial felt tip pens inks.

PubMed

Saviello, Daniela; Trabace, Maddalena; Alyami, Abeer; Mirabile, Antonio; Giorgi, Rodorico; Baglioni, Piero; Iacopino, Daniela

2018-05-01

The development of protocols for the protection of the large patrimony of works of art created by felt tip pen media since the 1950's requires detailed knowledge of the main dyes constituting commercial ink mixtures. In this work Surface Enhanced Raman Scattering (SERS) and UV-vis spectroscopy were used for the first time for the systematic identification of dye composition in commercial felt tip pens. A large selection of pens comprising six colors of five different brands was analyzed. Intense SERS spectra were obtained for all colors, allowing identification of main dye constituents. Poinceau 4R and Eosin dyes were found to be the main constituents of red and pink colors; Rhodamine and Tartrazine were found in orange and yellow colors; Erioglaucine was found in green and blue colors. UV-vis analysis of the same inks was used to support SERS findings but also to unequivocally assign some uncertain dye identifications, especially for yellow and orange colors. The spectral data of all felt tip pens collected through this work were assembled in a database format. The data obtained through this systematic investigation constitute the basis for the assembly of larger reference databases that ultimately will support the development of conservation protocols for the long term preservation of modern art collections. Copyright © 2018 Elsevier B.V. All rights reserved.

A tipping point in refreezing accelerates mass loss of Greenland's glaciers and ice caps.

PubMed

Noël, B; van de Berg, W J; Lhermitte, S; Wouters, B; Machguth, H; Howat, I; Citterio, M; Moholdt, G; Lenaerts, J T M; van den Broeke, M R

2017-03-31

Melting of the Greenland ice sheet (GrIS) and its peripheral glaciers and ice caps (GICs) contributes about 43% to contemporary sea level rise. While patterns of GrIS mass loss are well studied, the spatial and temporal evolution of GICs mass loss and the acting processes have remained unclear. Here we use a novel, 1 km surface mass balance product, evaluated against in situ and remote sensing data, to identify 1997 (±5 years) as a tipping point for GICs mass balance. That year marks the onset of a rapid deterioration in the capacity of the GICs firn to refreeze meltwater. Consequently, GICs runoff increases 65% faster than meltwater production, tripling the post-1997 mass loss to 36±16 Gt -1 , or ∼14% of the Greenland total. In sharp contrast, the extensive inland firn of the GrIS retains most of its refreezing capacity for now, buffering 22% of the increased meltwater production. This underlines the very different response of the GICs and GrIS to atmospheric warming.

A tipping point in refreezing accelerates mass loss of Greenland's glaciers and ice caps

PubMed Central

Noël, B.; van de Berg, W. J; Lhermitte, S.; Wouters, B.; Machguth, H.; Howat, I.; Citterio, M.; Moholdt, G.; Lenaerts, J. T. M.; van den Broeke, M. R.

2017-01-01

Melting of the Greenland ice sheet (GrIS) and its peripheral glaciers and ice caps (GICs) contributes about 43% to contemporary sea level rise. While patterns of GrIS mass loss are well studied, the spatial and temporal evolution of GICs mass loss and the acting processes have remained unclear. Here we use a novel, 1 km surface mass balance product, evaluated against in situ and remote sensing data, to identify 1997 (±5 years) as a tipping point for GICs mass balance. That year marks the onset of a rapid deterioration in the capacity of the GICs firn to refreeze meltwater. Consequently, GICs runoff increases 65% faster than meltwater production, tripling the post-1997 mass loss to 36±16 Gt−1, or ∼14% of the Greenland total. In sharp contrast, the extensive inland firn of the GrIS retains most of its refreezing capacity for now, buffering 22% of the increased meltwater production. This underlines the very different response of the GICs and GrIS to atmospheric warming. PMID:28361871

Surface-sensitive Raman spectroscopy of collagen I fibrils.

PubMed

Gullekson, Corinne; Lucas, Leanne; Hewitt, Kevin; Kreplak, Laurent

2011-04-06

Collagen fibrils are the main constituent of the extracellular matrix surrounding eukaryotic cells. Although the assembly and structure of collagen fibrils is well characterized, very little appears to be known about one of the key determinants of their biological function-namely, the physico-chemical properties of their surface. One way to obtain surface-sensitive structural and chemical data is to take advantage of the near-field nature of surface- and tip-enhanced Raman spectroscopy. Using Ag and Au nanoparticles bound to Collagen type-I fibrils, as well as tips coated with a thin layer of Ag, we obtained Raman spectra characteristic to the first layer of collagen molecules at the surface of the fibrils. The most frequent Raman peaks were attributed to aromatic residues such as phenylalanine and tyrosine. In several instances, we also observed Amide I bands with a full width at half-maximum of 10-30 cm(-1). The assignment of these Amide I band positions suggests the presence of 3(10)-helices as well as α- and β-sheets at the fibril's surface. Copyright © 2011 Biophysical Society. Published by Elsevier Inc. All rights reserved.

GRACE-FO Prelaunch Briefing

NASA Image and Video Library

2018-05-21

NASA Headquarters Public Affairs Officer Steve Cole moderates a Gravity Recovery and Climate Experiment Follow-On (GRACE-FO) mission prelaunch media briefing, Monday, May 21, 2018, at Vandenberg Air Force Base in California. The twin GRACE-FO spacecraft will measure changes in how mass is redistributed within and among Earth's atmosphere, oceans, land and ice sheets, as well as within Earth itself. Photo Credit: (NASA/Bill Ingalls)

Facts about Employer Support for Child Care. NCJW Center for the Child Fact Sheet Number 2. Revised.

ERIC Educational Resources Information Center

National Council of Jewish Women, New York, NY. Center for the Child.

Media coverage has given rise to various misconceptions about the scope of employer support for child care and the kinds of assistance most useful to employees. Some may believe that employer support for child care involves opening a child care center at the workplace. While employer-sponsored child care centers are highly publicized, they…

Electrochemical investigations of Co3Fe-RGO as a bifunctional catalyst for oxygen reduction and evolution reactions in alkaline media

NASA Astrophysics Data System (ADS)

Kumar, Surender; Kumar, Divyaratan; Kishore, Brij; Ranganatha, Sudhakar; Munichandraiah, Nookala; Venkataramanan, Natarajan S.

2017-10-01

Nanoparticles of Co3Fe alloy is prepared on reduced graphene oxide (RGO) sheets by modified polyol method. Synthesized alloy particles are characterized by various physicochemical techniques. TEM and SEM pictures showed homogeneously dispersed alloy nanoparticles on the RGO sheets. Electrochemistry of alloy nanoparticles is investigated in alkaline medium. The result shows that oxygen evaluation reaction (OER) activity of Co3Fe-RGO is higher than Pt-black particles. RDE studies in alkaline medium shows that oxygen reduction reaction (ORR) follow four electron pathway. It is suggest that Co3Fe-RGO is an efficient non-precious catalyst for oxygen (ORR/OER) reactions in alkaline electrolyte for PEMFC applications.

In Situ Synthesis of Reduced Graphene Oxide and Gold Nanocomposites for Nanoelectronics and Biosensing.

PubMed

Dong, Xiaochen; Huang, Wei; Chen, Peng

2011-12-01

In this study, an in situ chemical synthesis approach has been developed to prepare graphene-Au nanocomposites from chemically reduced graphene oxide (rGO) in aqueous media. UV-Vis absorption, atomic force microscopy, scanning electron microscopy, transmission electron microscopy, and Raman spectroscopy were used to demonstrate the successful attachment of Au nanoparticles to graphene sheets. Configured as field-effect transistors (FETs), the as-synthesized single-layered rGO-Au nanocomposites exhibit higher hole mobility and conductance when compared to the rGO sheets, promising its applications in nanoelectronics. Furthermore, we demonstrate that the rGO-Au FETs are able to label-freely detect DNA hybridization with high sensitivity, indicating its potentials in nanoelectronic biosensing.