49 CFR 178.273 - Approval of Specification UN portable tanks.

Code of Federal Regulations, 2010 CFR

2010-10-01

... including, but not limited to, ensuring that the quality control, design calculations and required tests are... necessary to ensure that the design meets the relevant specification. (ii) The manufacturer's serial number that will be assigned to each portable tank. (iii) A statement as to whether the design type has been...

49 CFR 178.273 - Approval of Specification UN portable tanks.

Code of Federal Regulations, 2014 CFR

2014-10-01

... including, but not limited to, ensuring that the quality control, design calculations and required tests are... necessary to ensure that the design meets the relevant specification. (ii) The manufacturer's serial number that will be assigned to each portable tank. (iii) A statement as to whether the design type has been...

Fabrication of precise aperiodic multichannel fibre Bragg grating filters for spectral line suppression in hydrogenated standard telecommunications fibre.

PubMed

Gbadebo, Adenowo A; Turitsyna, Elena G; Williams, John A R

2018-01-22

We demonstrate the design and fabrication of multichannel fibre Bragg gratings (FBGs) with aperiodic channel spacings. These will be suitable for the suppression of specific spectral lines such as OH emission lines in the near infrared (NIR) which degrade ground based astronomical imaging. We discuss the design process used to meet a given specification and the fabrication challenges that can give rise to errors in the final manufactured device. We propose and demonstrate solutions to meet these challenges.

Hierarchical specification of the SIFT fault tolerant flight control system

NASA Technical Reports Server (NTRS)

Melliar-Smith, P. M.; Schwartz, R. L.

1981-01-01

The specification and mechanical verification of the Software Implemented Fault Tolerance (SIFT) flight control system is described. The methodology employed in the verification effort is discussed, and a description of the hierarchical models of the SIFT system is given. To meet the objective of NASA for the reliability of safety critical flight control systems, the SIFT computer must achieve a reliability well beyond the levels at which reliability can be actually measured. The methodology employed to demonstrate rigorously that the SIFT computer meets as reliability requirements is described. The hierarchy of design specifications from very abstract descriptions of system function down to the actual implementation is explained. The most abstract design specifications can be used to verify that the system functions correctly and with the desired reliability since almost all details of the realization were abstracted out. A succession of lower level models refine these specifications to the level of the actual implementation, and can be used to demonstrate that the implementation has the properties claimed of the abstract design specifications.

Final design review summary report for the TN-WHC cask and transportation system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kee, A.T.

1997-01-17

This document represents comments generated from a review of Transnuclear`s Final Design Package distributed on December 10, 1996 and a review of the Final Design Analysis Report meeting held on December 17 & 18, 1996. The Final design describes desicn features and presents final analyses @j performed to fabricate and operate the system while meeting the Cask/Transportation Functions and Requirements, WHC-SD-SNF-FRD-011, Rev. 0 and specification WHC-S-0396, Rev. 1.

Advanced Small Modular Reactor (SMR) Probabilistic Risk Assessment (PRA) Technical Exchange Meeting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, Curtis

2013-09-01

During FY13, the INL developed an advanced SMR PRA framework which has been described in the report Small Modular Reactor (SMR) Probabilistic Risk Assessment (PRA) Detailed Technical Framework Specification, INL/EXT-13-28974 (April 2013). In this framework, the various areas are considered: Probabilistic models to provide information specific to advanced SMRs Representation of specific SMR design issues such as having co-located modules and passive safety features Use of modern open-source and readily available analysis methods Internal and external events resulting in impacts to safety All-hazards considerations Methods to support the identification of design vulnerabilities Mechanistic and probabilistic data needs to support modelingmore » and tools In order to describe this framework more fully and obtain feedback on the proposed approaches, the INL hosted a technical exchange meeting during August 2013. This report describes the outcomes of that meeting.« less

49 CFR 173.415 - Authorized Type A packages.

Code of Federal Regulations, 2014 CFR

2014-10-01

... tests and an engineering evaluation or comparative data showing that the construction methods, packaging design, and materials of construction comply with that specification. After January 1, 2017 each offeror... meets the pertinent design and performance requirements for a DOT 7A Type A specification package. (2...

Methodologies for Root Locus and Loop Shaping Control Design with Comparisons

NASA Technical Reports Server (NTRS)

Kopasakis, George

2017-01-01

This paper describes some basics for the root locus controls design method as well as for loop shaping, and establishes approaches to expedite the application of these two design methodologies to easily obtain control designs that meet requirements with superior performance. The two design approaches are compared for their ability to meet control design specifications and for ease of application using control design examples. These approaches are also compared with traditional Proportional Integral Derivative (PID) control in order to demonstrate the limitations of PID control. Robustness of these designs is covered as it pertains to these control methodologies and for the example problems.

40 CFR 264.1085 - Standards: Surface impoundments.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the surface impoundment by installing and operating either of the following: (1) A floating membrane... from a surface impoundment using a floating membrane cover shall meet the requirements specified in... floating membrane cover designed to meet the following specifications: (i) The floating membrane cover...

76 FR 52944 - Environmental Management Site-Specific Advisory Board, Oak Ridge Reservation

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-24

... Agenda: The main meeting presentation will be an overview of URS/CH2M Oak Ridge LLC (UCOR), the new prime... agenda. The Deputy Designated Federal Officer is empowered to conduct the meeting in a fashion that will...

Liquid rocket engine turbines

NASA Technical Reports Server (NTRS)

1974-01-01

Criteria for the design and development of turbines for rocket engines to meet specific performance, and installation requirements are summarized. The total design problem, and design elements are identified, and the current technology pertaining to these elements is described. Recommended practices for achieving a successful design are included.

Wind/Tornado Guidelines Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ng, D.S.; Holman, G.S.

1991-10-01

This report documents the strategy employed to develop recommended wind/tornado hazard design guidelines for a New Production Reactor (NRP) currently planned for either the Idaho National Engineering Laboratory (INEL) or the Savannah River (SR) site. The Wind/Tornado Working Group (WTWG), comprising six nationally recognized experts in structural engineering, wind engineering, and meteorology, formulated an independent set of guidelines based on site-specific wind/tornado hazard curves and state-of-the-art tornado missile technology. The basic philosophy was to select realistic wind and missile load specifications, and to meet performance goals by applying conservative structural response evaluation and acceptance criteria. Simplified probabilistic risk analyses (PRAs)more » for wind speeds and missile impact were performed to estimate annual damage risk frequencies for both the INEL and SR sites. These PRAs indicate that the guidelines will lead to facilities that meet the US Department of Energy (DOE) design requirements and that the Nuclear Regulatory Commission guidelines adopted by the DOE for design are adequate to meet the NPR safety goals.« less

Manufacturing plastic injection optical molds

NASA Astrophysics Data System (ADS)

Bourque, David

2008-08-01

ABCO Tool & Die, Inc. is a mold manufacturer specializing in the manufacturing of plastic injection molds for molded optical parts. The purpose of this presentation is to explain the concepts and procedures required to build a mold that produces precision optical parts. Optical molds can produce a variety of molded parts ranging from safety eyewear to sophisticated military lens parts, which must meet precise optical specifications. The manufacturing of these molds begins with the design engineering of precision optical components. The mold design and the related optical inserts are determined based upon the specific optical criteria and optical surface geometry. The mold manufacturing techniques will be based upon the optical surface geometry requirements and specific details. Manufacturing processes used will be specific to prescribed geometrical surface requirements of the molded part. The combined efforts result in a robust optical mold which can produce molded parts that meet the most precise optical specifications.

Incorporating Learning Objects in a Curriculum Re-Design to Meet Needs of Students with Specific Learning Disabilities in Illinois Agricultural Education Programs

ERIC Educational Resources Information Center

Pense, Seburn L.; Calvin, Jennifer; Watson, Dennis G.; Wakefield, Dexter B.

2012-01-01

A quasi-experimental pilot study of curriculum re-design using Learning Objects (LO) to instruct agricultural education students with Specific Learning Disabilities (SLD) was conducted in five high schools in the federally designated economically distressed area, the Illinois Delta Region. Six LOs were developed based on a unit of instruction in…

Engineering sciences design. Design and implementation of components for a bioregenerative system for growing higher order plants in space

NASA Technical Reports Server (NTRS)

Nevill, Gale E., Jr.

1989-01-01

The primary goal was to address specific needs in the design of an integrated system to grow higher plants in space. With the needs defined, the emphasis was placed on the design and fabrication of devices to meet these needs. Specific attention was placed on a hand-held harvester, a nutrient concentration sensor, an air-water separator, and a closed-loop biological system simulation.

Real-time design with peer tasks

NASA Technical Reports Server (NTRS)

Goforth, Andre; Howes, Norman R.; Wood, Jonathan D.; Barnes, Michael J.

1995-01-01

We introduce a real-time design methodology for large scale, distributed, parallel architecture, real-time systems (LDPARTS), as an alternative to those methods using rate or dead-line monotonic analysis. In our method the fundamental units of prioritization, work items, are domain specific objects with timing requirements (deadlines) found in user's specification. A work item consists of a collection of tasks of equal priority. Current scheduling theories are applied with artifact deadlines introduced by the designer whereas our method schedules work items to meet user's specification deadlines (sometimes called end-to-end deadlines). Our method supports these scheduling properties. Work item scheduling is based on domain specific importance instead of task level urgency and still meets as many user specification deadlines as can be met by scheduling tasks with respect to urgency. Second, the minimum (closest) on-line deadline that can be guaranteed for a work item of highest importance, scheduled at run time, is approximately the inverse of the throughput, measured in work items per second. Third, throughput is not degraded during overload and instead of resorting to task shedding during overload, the designer can specify which work items to shed. We prove these properties in a mathematical model.

Targeting treatment technologies to address specific stormwater pollutants and numeric discharge limits.

PubMed

Clark, Shirley E; Pitt, Robert

2012-12-15

Stormwater treatment is entering a new phase with stormwater management systems being required to meet specific numeric objectives, as opposed to the historic approach of meeting guidance-document-provided percent removal rates. Meeting numeric discharge requirements will require designers to better understand and apply the physical, chemical, and biological processes underpinning these treatment technologies. This critical review paper focuses on the potential unit treatment operations available for stormwater treatment and outlines how to identify the most applicable treatment options based on the needed pollutant removal goals. Copyright © 2012 Elsevier Ltd. All rights reserved.

National Launch System Space Transportation Main Engine

NASA Technical Reports Server (NTRS)

Hoodless, Ralph M., Jr.; Monk, Jan C.; Cikanek, Harry A., III

1991-01-01

The present liquid-oxygen/liquid-hydrogen engine is described as meeting the specific requirements of the National Launch System (NLS) Program including cost-effectiveness and robustness. An overview of the NLS and its objectives is given which indicates that the program aims to develop a flexible launch system to meet security, civil, and commercial needs. The Space Transportation Main Engine (STME) provides core and boost propulsion for the 1.5-stage vehicle and core propulsion for the solid booster vehicle. The design incorporates step-throttling, order-of-magnitude reductions in welds, and configuration targets designed to optimize robustness. The STME is designed to provide adaptable and dependable propulsion while minimizing recurring costs and is designed to meet the needs of NLS and other typical space-transportation programs currently being planned.

40 CFR 265.1086 - Standards: Surface impoundments.

Code of Federal Regulations, 2010 CFR

2010-07-01

... floating membrane cover in accordance with the provisions specified in paragraph (c) of this section; or (2... emissions from a surface impoundment using a floating membrane cover shall meet the requirements specified... with a floating membrane cover designed to meet the following specifications: (i) The floating membrane...

Refuge alternatives relief valve testing and design

PubMed Central

Lutz, T.J.; Bissert, P.T.; Homce, G.T.; Yonkey, J.A.

2016-01-01

The U.S. National Institute for Occupational Safety and Health (NIOSH) has been researching refuge alternatives (RAs) since 2007. RAs typically have built-in pressure relief valves (PRVs) to prevent the unit from reaching unsafe pressures. The U.S. Mine Safety and Health Administration requires that these valves vent the chamber at a maximum pressure of 1.25 kPa (0.18 psi, 5.0 in. H2O), or as specified by the manufacturer, above mine atmospheric pressure in the RA. To facilitate PRV testing, an instrumented benchtop test fixture was developed using an off-the-shelf centrifugal blower and ductwork. Relief pressures and flow characteristics were measured for three units: (1) a modified polyvinyl chloride check valve, (2) an off-the-shelf brass/cast-iron butterfly check valve and (3) a commercially available valve that was designed specifically for one manufacturer’s steel prefabricated RAs and had been adapted for use in one mine operator’s built-in-place RA. PRVs used in tent-style RAs were not investigated. The units were tested with different modifications and configurations in order to check compliance with Title 30 Code of Federal Regulations, or 30 CFR, regulations. The commercially available relief valve did not meet the 30 CFR relief pressure specification but may meet the manufacturer’s specification. Alternative valve designs were modified to meet the 30 CFR relief pressure specification, but all valve designs will need further design research to examine survivability in the event of a 103 kPa (15.0 psi) impulse overpressure during a disaster. PMID:28018003

Superconducting linear actuator

NASA Technical Reports Server (NTRS)

Johnson, Bruce; Hockney, Richard

1993-01-01

Special actuators are needed to control the orientation of large structures in space-based precision pointing systems. Electromagnetic actuators that presently exist are too large in size and their bandwidth is too low. Hydraulic fluid actuation also presents problems for many space-based applications. Hydraulic oil can escape in space and contaminate the environment around the spacecraft. A research study was performed that selected an electrically-powered linear actuator that can be used to control the orientation of a large pointed structure. This research surveyed available products, analyzed the capabilities of conventional linear actuators, and designed a first-cut candidate superconducting linear actuator. The study first examined theoretical capabilities of electrical actuators and determined their problems with respect to the application and then determined if any presently available actuators or any modifications to available actuator designs would meet the required performance. The best actuator was then selected based on available design, modified design, or new design for this application. The last task was to proceed with a conceptual design. No commercially-available linear actuator or modification capable of meeting the specifications was found. A conventional moving-coil dc linear actuator would meet the specification, but the back-iron for this actuator would weigh approximately 12,000 lbs. A superconducting field coil, however, eliminates the need for back iron, resulting in an actuator weight of approximately 1000 lbs.

[Designing the Annual Meeting and Active Learning System].

PubMed

Kawamura, Kazumi

2018-01-01

　At the 10th Annual Meeting of the Japanese Society for Pharmaceutical Palliative Care and Sciences our theme centered on active learning systems where adult learners engage on their own initiative. Many of the participants were pharmacists active in clinical practices. Regardless of their specialized skill-sets, pharmacists are constantly faced with difficult challenges in their daily work. Passive, one-way lectures are one resource for them, but unfortunately such lectures provide limited insights for resolving concrete problems. The present meeting aimed to show participants how to obtain information they need to solve specific real-world problems. This paper summarizes how we planned this year's meeting, including details about the debate symposium, social lunch, and online questionnaires. All these elements had the end goal of enabling learners proactivity to become their own best resource for learning. It is sincerely hoped that the design and execution of this meeting will prove resourceful for future annual meetings.

75 FR 9220 - Meeting of the Advisory Committee on Minority Health

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-01

... each racial and ethnic minority group and on the development of goals and specific program activities... to improve the health of racial and ethnic minority populations through the development of health... designated contact person at least fourteen (14) business days prior to the meeting. Members of the public...

Manual for Accessibility: [Conference, Meeting, and Lodging Facilities]. Revised.

ERIC Educational Resources Information Center

National Rehabilitation Association, Alexandria, VA.

This illustrated manual and survey forms are designed to be used by organizations, hotel and restaurant associations, interested individuals and others as a guide for selecting accessible conference, meeting, and lodging facilities. The guidelines can also be used with existing facilities to identify specific modifications and accommodations. The…

Unique technical innovations for short rotation woody crops research and development

Treesearch

Adam H. Wiese; Ronald S., Jr. Zalesny

2006-01-01

Often technology that is available to conduct short rotation woody crops (SRWC) research is too expensive, difficult to operate, cumbersome, and/or impractical for meeting sample size requirements. Thus, we have designed, constructed, and tested technical innovations that have allowed us to meet our specific experimental needs.

Waveform generation in the EETS

NASA Astrophysics Data System (ADS)

Wilshire, J. P.

1985-05-01

Design decisions and analysis for the waveform generation portion of an electrical equipment test set are discussed. This test set is unlike conventional ATE in that it is portable and designed to operate in forward area sites for the USMC. It is also unique in that it provides for functional testing for 32 electronic units from the AV-88 Harrier II aircraft. Specific requirements for the waveform generator are discussed, including a wide frequency range, high resolution and accuracy, and low total harmonic distortion. Several approaches to meet these requirements are considered and a specific concept is presented in detail, which consists of a digitally produced waveform that feeds a deglitched analog conversion circuit. Rigorous mathematical analysis is presented to prove that this concept meets the requirements. Finally, design alternatives and enhancements are considered.

Rotor-state feedback in the design of flight control laws for a hovering helicopter

NASA Technical Reports Server (NTRS)

Takahashi, Marc D.

1994-01-01

The use of rigid-body and rotor-state feedback gains in the design of helicopter flight control laws was investigated analytically on a blade element, articulated rotor, helicopter model. The study was conducted while designing a control law to meet an existing military rotorcraft handling qualities design specification (ADS-33C) in low-speed flight. A systematic approach to meet this specification was developed along with an assessment of the function of these gains in the feedback loops. Using the results of this assessment, the pitch and roll crossover behavior was easily modified by adjusting the body attitude and rotor-flap feedback gains. Critical to understanding the feedback gains is that the roll and pitch rate dynamics each have second-order behavior, not the classic first-order behavior, which arises from a quasi-static rotor, six degree-of-freedom model.

Optical design for consumer products

NASA Astrophysics Data System (ADS)

Gupta, Anurag

2014-10-01

Optical engineers often limit their focus on meeting the provided targets on performance and geometry and assume that the specifications are largely non-negotiable. Such approach ignores the value proposition behind the product and the challenges associated with overall product design, manufacturing, business development and legal issues. As a result, the design effort can be expensive, time consuming and can result in product failure. We discuss a product based systems engineering approach that leads to an application specific optical design that is more effective and efficient to implement.

Modeling of additive manufacturing processes for metals: Challenges and opportunities

DOE PAGES

Francois, Marianne M.; Sun, Amy; King, Wayne E.; ...

2017-01-09

Here, with the technology being developed to manufacture metallic parts using increasingly advanced additive manufacturing processes, a new era has opened up for designing novel structural materials, from designing shapes and complex geometries to controlling the microstructure (alloy composition and morphology). The material properties used within specific structural components are also designable in order to meet specific performance requirements that are not imaginable with traditional metal forming and machining (subtractive) techniques.

Space shuttle visual simulation system design study

NASA Technical Reports Server (NTRS)

1973-01-01

A recommendation and a specification for the visual simulation system design for the space shuttle mission simulator are presented. A recommended visual system is described which most nearly meets the visual design requirements. The cost analysis of the recommended system covering design, development, manufacturing, and installation is reported. Four alternate systems are analyzed.

The design, development, and implementation of a data acquisition and handling system at Basin Electric Power Cooperative

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baranowski, S.T.; Culp, L.R.; Jonas, T.S.

1995-12-31

The Clean Air Act Amendments of 1990 require all Phase 1 and 2 utilities to install Continuous Emissions Monitoring Systems (CEMS), which can consist of instrumentation including analyzers and a Data Acquisition and Handling System (DAHS). To meet these requirements, Basin Electric Power Cooperative contracted with Black and Veatch to design and develop a DAHS which would meet all 40 CFR Part 75 requirements. Basin Electric provided the specifications for the DAHS and the graphical user interface, and B and V designed, developed, and installed a DAHS at 3 units at Laramie River Station, 2 units at Antelope Valley Station,more » and 2 units at Leland Olds Station. B and V utilized the existing equipment, adding to it a unique DAHS design. B and V designed and implemented the DAHS which operates in the OS/2 environment to interface with multiple programmable logic controllers. This unique software was written in modular form so that multiple programs run in unison, monitoring each other for errors to ensure continuous operation. The reporting structure is flexible to allow for a variety of formats, including those specifically required by the state to meet CAAA guidelines. Today, these seven units are in operation and comply with the CAAA. This paper describes the issues faced during specification, general design, compliance, and implementation of the DAHS at BEPC, including the lessons learned. The continuous emissions monitoring (CEM) system for each unit at BEPC consisted of a set of dilution probe analyzers for measuring SO{sub 2}, NO{sub x}, and CO{sub 2}.« less

40 CFR 63.1184 - What do I need to know about the design specifications, installation, and operation of a bag leak...

Code of Federal Regulations, 2010 CFR

2010-07-01

... design specifications, installation, and operation of a bag leak detection system? 63.1184 Section 63... bag leak detection system? A bag leak detection system must meet the following requirements: (a) The bag leak detection system must be certified by the manufacturer to be capable of detecting PM...

Functional design specification for Stowage List And Hardware Tracking System (SLAHTS). [space shuttles

NASA Technical Reports Server (NTRS)

Keltner, D. J.

1975-01-01

This functional design specification defines the total systems approach to meeting the requirements stated in the Detailed Requirements Document for Stowage List and Hardware Tracking System for the space shuttle program. The stowage list and hardware tracking system is identified at the system and subsystem level with each subsystem defined as a function of the total system.

Reliable fusion of control and sensing in intelligent machines. Thesis

NASA Technical Reports Server (NTRS)

Mcinroy, John E.

1991-01-01

Although robotics research has produced a wealth of sophisticated control and sensing algorithms, very little research has been aimed at reliably combining these control and sensing strategies so that a specific task can be executed. To improve the reliability of robotic systems, analytic techniques are developed for calculating the probability that a particular combination of control and sensing algorithms will satisfy the required specifications. The probability can then be used to assess the reliability of the design. An entropy formulation is first used to quickly eliminate designs not capable of meeting the specifications. Next, a framework for analyzing reliability based on the first order second moment methods of structural engineering is proposed. To ensure performance over an interval of time, lower bounds on the reliability of meeting a set of quadratic specifications with a Gaussian discrete time invariant control system are derived. A case study analyzing visual positioning in robotic system is considered. The reliability of meeting timing and positioning specifications in the presence of camera pixel truncation, forward and inverse kinematic errors, and Gaussian joint measurement noise is determined. This information is used to select a visual sensing strategy, a kinematic algorithm, and a discrete compensator capable of accomplishing the desired task. Simulation results using PUMA 560 kinematic and dynamic characteristics are presented.

Career/Life Planning for Divorced Women: An Overview.

ERIC Educational Resources Information Center

Kitabchi, Gloria; And Others

1979-01-01

Several programs designed to meet the needs of mature women could be adapted to meet the special needs of the mature divorced woman. Career counseling for the divorced client must address the specific emotional factors involved in divorce, and aim toward total life planning, not simple adjustment to a life crisis and job placement. (Author)

Professional Certification

EPA Pesticide Factsheets

WaterSense recognizes certification programs for irrigation professionals that meet the specification criteria. Certification programs cover three areas: irrigation system design, installation and maintenance, and system auditing.

40 CFR 76.10 - Alternative emission limitations.

Code of Federal Regulations, 2013 CFR

2013-07-01

...; and (ii) The installed NOX emission control system has been designed to meet the applicable emission... that the unit and NOX emission control system were operated in accordance with the bid and design specifications on which the design of the NOX emission control system was based; and (C) Unit operating data as...

40 CFR 76.10 - Alternative emission limitations.

Code of Federal Regulations, 2010 CFR

2010-07-01

...; and (ii) The installed NOX emission control system has been designed to meet the applicable emission... that the unit and NOX emission control system were operated in accordance with the bid and design specifications on which the design of the NOX emission control system was based; and (C) Unit operating data as...

Status Of the ILC Main Linac Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saini, Arun; Kapin, Valery; Solyak, Nikolay

2017-05-01

International Linear collider (ILC) is a proposed accelerator facility which is primarily based on two 11-km long superconducting main linacs. In this paper we present recent updates on the main linac design and discuss changes made in order to meet specification outlined in the technical design report (TDR).

Evolutionary Design of a Phased Array Antenna Element

NASA Technical Reports Server (NTRS)

Globus, Al; Linden, Derek; Lohn, Jason

2006-01-01

We present an evolved S-band phased array antenna element design that meets the requirements of NASA's TDRS-C communications satellite scheduled for launch early next decade. The original specification called for two types of elements, one for receive only and one for transmit/receive. We were able to evolve a single element design that meets both specifications thereby simplifying the antenna and reducing testing and integration costs. The highest performance antenna found using a genetic algorithm and stochastic hill-climbing has been fabricated and tested. Laboratory results are largely consistent with simulation. Researchers have been investigating evolutionary antenna design and optimization since the early 1990s, and the field has grown in recent years its computer speed has increased and electromagnetic simulators have improved. Many antenna types have been investigated, including wire antennas, antenna arrays and quadrifilar helical antennas. In particular, our laboratory evolved a wire antenna design for NASA's Space Technology 5 (ST5) spacecraft. This antenna has been fabricated, tested, and is scheduled for launch on the three spacecraft in 2006.

33 CFR 279.5 - Policy.

Code of Federal Regulations, 2010 CFR

2010-07-01

... utilize an interdisciplinary team with leadership by planning, and participation from engineering, design.... Subsequent aspects of planning, development, and management for the specific project will be directed to... management plans for each specific water resource project, including at least one public meeting. The...

Methods for Meeting the Intent of the ADA in Sidewalk Cross-Slope Design

DOT National Transportation Integrated Search

2000-01-01

This summary report is a review of research undertaken to determine appropriate sidewalk cross-slope design in accordance wit the Americans with Disabilities Act (ADA). The research methods used are described and specific recommendations are provided...

Windmills by Design: Purposeful Curriculum Design to Meet Next Generation Science Standards in a 9-12 Physics Classroom

ERIC Educational Resources Information Center

Concannon, James; Brown, Patrick L.

2017-01-01

The "Next Generation Science Standards" (NGSS) challenges science teachers to think beyond specific content standards when considering how to design and implement curriculum. This lesson, "Windmills by Design," is an insightful lesson in how science teachers can create and implement a cross-cutting lesson to teach the concepts…

Promoting Health-Related Fitness for Elementary Students with Intellectual Disabilities through a Specifically Designed Activity Program

ERIC Educational Resources Information Center

Davis, Kathryn; Zhang, Guili; Hodson, Patricia

2011-01-01

The Motivate, Adapt, and Play Program was specifically designed as an adapted physical activity (PA) program for students with intellectual disabilities (ID) to meet required school PA policies to combat childhood obesity. The policies commonly require a minimum of 30 min of PA per school day. A study was undertaken to test the efficacy of the…

76 FR 16785 - Meeting for Software Developers on the Technical Specifications for Common Formats for Patient...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-25

... Software Developers on the Technical Specifications for Common Formats for Patient Safety Data Collection... designed as an interactive forum where PSOs and software developers can provide input on these technical... updated event descriptions, forms, and technical specifications for software developers. As an update to...

49 CFR 173.32 - Requirements for the use of portable tanks.

Code of Federal Regulations, 2014 CFR

2014-10-01

... portable tanks. (1) The bursting strength of any piping and fittings must be at least four times the design... specified portable tank must meet the same design profile; for example, a DOT Specification 51 portable tank... manufactured portable tanks must conform to the requirements for the design, construction and approval of UN...

75 FR 53379 - Fisheries off West Coast States; Pacific Coast Groundfish Fishery Management Plan; Amendments 20...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-31

... same time, the design of this program is mindful of confidentiality concerns and the compliance burden... groundfish trawl fishery. To meet these needs, NMFS has designed mandatory survey questionnaires for catcher... plant. The data collection would be done on an annual basis, with specific questionnaires designed for...

45 CFR 1356.83 - Reporting requirements and data elements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... specifically designed instruction, at no cost to parents, to meet the unique needs of a child with a disability... element must be left blank. (21) Academic support. Academic supports are services designed to help a youth... are services designed to help a youth enter or complete a post-secondary education and include the...

45 CFR 1356.83 - Reporting requirements and data elements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... specifically designed instruction, at no cost to parents, to meet the unique needs of a child with a disability... element must be left blank. (21) Academic support. Academic supports are services designed to help a youth... are services designed to help a youth enter or complete a post-secondary education and include the...

45 CFR 1356.83 - Reporting requirements and data elements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... specifically designed instruction, at no cost to parents, to meet the unique needs of a child with a disability... element must be left blank. (21) Academic support. Academic supports are services designed to help a youth... are services designed to help a youth enter or complete a post-secondary education and include the...

45 CFR 1356.83 - Reporting requirements and data elements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... specifically designed instruction, at no cost to parents, to meet the unique needs of a child with a disability... element must be left blank. (21) Academic support. Academic supports are services designed to help a youth... are services designed to help a youth enter or complete a post-secondary education and include the...

Advanced electric motor technology: Flux mapping

NASA Technical Reports Server (NTRS)

Doane, George B., III; Campbell, Warren; Brantley, Larry W.; Dean, Garvin

1992-01-01

This report contains the assumptions, mathematical models, design methodology, and design points involved with the design of an electromechanical actuator (EMA) suitable for directing the thrust vector of a large MSFC/NASA launch vehicle. Specifically the design of such an actuator for use on the upcoming liquid fueled National Launch System (NLS) is considered culminating in a point design of both the servo system and the electric motor needed. A major thrust of the work is in selecting spur gear and roller screw reduction ratios to achieve simultaneously wide bandwidth, maximum power transfer, and disturbance rejection while meeting specified horsepower requirements at a given stroking speed as well as a specified maximum stall force. An innovative feedback signal is utilized in meeting these diverse objectives.

Block 4 solar cell module design and test specification for residential applications

NASA Technical Reports Server (NTRS)

1978-01-01

Near-term design, qualification and acceptance requirements are provided for terrestrial solar cell modules suitable for incorporation in photovoltaic power sources (2 kW to 10 kW) applied to single family residential installations. Requirement levels and recommended design limits for selected performance criteria are specified for modules intended principally for rooftop installations. Modules satisfying the requirements of this specification fall into one of two categories, residential panel or residential shingle, both meeting general performance requirements plus additional category peculiar constraints.

Low Average Sidelobe Slot Array Antennas for Radiometer Applications

NASA Technical Reports Server (NTRS)

Rengarajan, Sembiam; Zawardzki, Mark S.; Hodges, Richard E.

2012-01-01

In radiometer applications, it is required to design antennas that meet low average sidelobe levels and low average return loss over a specified frequency bandwidth. It is a challenge to meet such specifications over a frequency range when one uses resonant elements such as waveguide feed slots. In addition to their inherent narrow frequency band performance, the problem is exacerbated due to modeling errors and manufacturing tolerances. There was a need to develop a design methodology to solve the problem. An iterative design procedure was developed by starting with an array architecture, lattice spacing, aperture distribution, waveguide dimensions, etc. The array was designed using Elliott s technique with appropriate values of the total slot conductance in each radiating waveguide, and the total resistance in each feed waveguide. Subsequently, the array performance was analyzed by the full wave method of moments solution to the pertinent integral equations. Monte Carlo simulations were also carried out to account for amplitude and phase errors introduced for the aperture distribution due to modeling errors as well as manufacturing tolerances. If the design margins for the average sidelobe level and the average return loss were not adequate, array architecture, lattice spacing, aperture distribution, and waveguide dimensions were varied in subsequent iterations. Once the design margins were found to be adequate, the iteration was stopped and a good design was achieved. A symmetric array architecture was found to meet the design specification with adequate margin. The specifications were near 40 dB for angular regions beyond 30 degrees from broadside. Separable Taylor distribution with nbar=4 and 35 dB sidelobe specification was chosen for each principal plane. A non-separable distribution obtained by the genetic algorithm was found to have similar characteristics. The element spacing was obtained to provide the required beamwidth and close to a null in the E-plane end-fire direction. Because of the alternating slot offsets, grating lobes called butterfly lobes are produced in non-principal planes close to the H-plane. An attempt to reduce the influence of such grating lobes resulted in a symmetric design.

Multicriteria Gain Tuning for Rotorcraft Flight Controls (also entitled The Development of the Conduit Advanced Control System Design and Evaluation Interface with a Case Study Application Fly by Wire Helicopter Design)

NASA Technical Reports Server (NTRS)

Biezad, Daniel

1997-01-01

Handling qualities analysis and control law design would seem to be naturally complimenting components of aircraft flight control system design, however these two closely coupled disciplines are often not well integrated in practice. Handling qualities engineers and control system engineers may work in separate groups within an aircraft company. Flight control system engineers and handling quality specialists may come from different backgrounds and schooling and are often not aware of the other group's research. Thus while the handling qualities specifications represent desired aircraft response characteristics, these are rarely incorporated directly in the control system design process. Instead modem control system design techniques are based on servo-loop robustness specifications, and simple representations of the desired control response. Comprehensive handling qualities analysis is often left until the end of the design cycle and performed as a check of the completed design for satisfactory performance. This can lead to costly redesign or less than satisfactory aircraft handling qualities when the flight testing phase is reached. The desire to integrate the fields of handling qualities and flight,control systems led to the development of the CONDUIT system. This tool facilitates control system designs that achieve desired handling quality requirements and servo-loop specifications in a single design process. With CONDUIT, the control system engineer is now able to directly design and control systems to meet the complete handling specifications. CONDUIT allows the designer to retain a preferred control law structure, but then tunes the system parameters to meet the handling quality requirements.

Biocatalysts: application and engineering for industrial purposes.

PubMed

Jemli, Sonia; Ayadi-Zouari, Dorra; Hlima, Hajer Ben; Bejar, Samir

2016-01-01

Enzymes are widely applied in various industrial applications and processes, including the food and beverage, animal feed, textile, detergent and medical industries. Enzymes screened from natural origins are often engineered before entering the market place because their native forms do not meet the requirements for industrial application. Protein engineering is concerned with the design and construction of novel enzymes with tailored functional properties, including stability, catalytic activity, reaction product inhibition and substrate specificity. Two broad approaches have been used for enzyme engineering, namely, rational design and directed evolution. The powerful and revolutionary techniques so far developed for protein engineering provide excellent opportunities for the design of industrial enzymes with specific properties and production of high-value products at lower production costs. The present review seeks to highlight the major fields of enzyme application and to provide an updated overview on previous protein engineering studies wherein natural enzymes were modified to meet the operational conditions required for industrial application.

Claims, Evidence and Achievement Level Descriptors as a Foundation for Item Design and Test Specifications

ERIC Educational Resources Information Center

Hendrickson, Amy; Huff, Kristen; Luecht, Ric

2009-01-01

[Slides] presented at the Annual Meeting of National Council on Measurement in Education (NCME) in San Diego, CA in April 2009. This presentation describes how the vehicles for gathering student evidence--task models and test specifications--are developed.

10 CFR Appendix C to Part 52 - Design Certification Rule for the AP600 Design

Code of Federal Regulations, 2013 CFR

2013-01-01

... design, in accordance with 10 CFR part 52, subpart B. The applicant for certification of the AP600 design... appendix. B. Generic technical specifications means the information, required by 10 CFR 50.36 and 50.36a... licensee must meet the requirement in Section III.B of this appendix to reference Tier 2 when referencing...

Engineering Design Challenges in a Science Curriculum

ERIC Educational Resources Information Center

Eisenkraft, Arthur

2011-01-01

Create a light and sound show to entertain friends. Design an improved safety device for a car. Develop a 2-3 minute voice-over for a sports clip explaining the physics involved in the sport. Modify the design of a roller coaster to meet the needs of a specific group of riders. Design an appliance package for a family limited by the power and…

Measure Twice, Build Once: Bench-Scale Testing to Evaluate Bioretention Media Design (Presentation)

EPA Science Inventory

Rain garden design manuals and guidelines typically recommend using native soils or engineered media that meet specifications for low content of clay, silt, fine and very fine sands, and organic matter. These characteristics promote stormwater infiltration and sorption of heavy ...

Lighting Control Best Practice Guide: Schools.

ERIC Educational Resources Information Center

2002

This publication offers design, specification, and installation guidance for lighting control appropriate for K-12 educational facilities. It features applications that illustrate the best control practices for a variety of spaces, facilitating lighting control design and application. Each best practice meets the provisions of relevant energy…

49 CFR 107.503 - Registration statement.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Inspector” or “Design Certifying Engineer”. The following language may be used. I certify that all Registered Inspectors and Design Certifying Engineers used in performance of the prescribed functions meet... requirements applicable to the functions to be performed. (5) A description of the specific functions to be...

Material Stream Strategy for Lithium and Inorganics (U)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Safarik, Douglas Joseph; Dunn, Paul Stanton; Korzekwa, Deniece Rochelle

Design Agency Responsibilities: Manufacturing Support to meet Stockpile Stewardship goals for maintaining the nuclear stockpile through experimental and predictive modeling capability. Development and maintenance of Manufacturing Science expertise to assess material specifications and performance boundaries, and their relationship to processing parameters. Production Engineering Evaluations with competence in design requirements, material specifications, and manufacturing controls. Maintenance and enhancement of Aging Science expertise to support Stockpile Stewardship predictive science capability.

CdSe TFT AMLCDE manufacturing process

NASA Astrophysics Data System (ADS)

Pritchard, Annette M.

1995-06-01

Active Matrix Liquid Crystal Displays, AMLCDs, based on Cadmium Selenide Thin Film Transistors, have been developed by Litton for a number of defence/avionics applications. Fabrication processed for the thin film transistor (TFT) arrays, color filters and liquid crystal cell assembly have been developed which enable the end product to meet the difficult environmental and performance specifications of military applications, while maintaining focus on cost and yield issues. The fabrication of the AMLCD products is now transitioning into a new production facility which has been designed specifically to meet the requirements of the defence/avionics marketplace.

AVERT User Manual

EPA Pesticide Factsheets

AVERT is a flexible modeling framework with a simple user interface designed specifically to meet the needs of state air quality planners and other interested stakeholders. Use this guide to get started.

34 CFR 606.7 - What definitions apply?

Code of Federal Regulations, 2012 CFR

2012-07-01

... implementation plan designed to meet one or more objectives. An activity is a part of a project and has its own... or improved programs and services, beyond those regularly budgeted, specifically designed to improve... expended by an institution of higher education for instruction, research, public service, academic support...

34 CFR 607.7 - What definitions apply?

Code of Federal Regulations, 2013 CFR

2013-07-01

... incorporated into an implementation plan designed to meet one or more objectives. An activity is a part of a..., specifically designed to improve the self sufficiency of the school. Educational and general expenditures means the total amount expended by an institution of higher education for instruction, research, public...

34 CFR 607.7 - What definitions apply?

Code of Federal Regulations, 2012 CFR

2012-07-01

... incorporated into an implementation plan designed to meet one or more objectives. An activity is a part of a..., specifically designed to improve the self sufficiency of the school. Educational and general expenditures means the total amount expended by an institution of higher education for instruction, research, public...

34 CFR 606.7 - What definitions apply?

Code of Federal Regulations, 2013 CFR

2013-07-01

... implementation plan designed to meet one or more objectives. An activity is a part of a project and has its own... or improved programs and services, beyond those regularly budgeted, specifically designed to improve... expended by an institution of higher education for instruction, research, public service, academic support...

34 CFR 606.7 - What definitions apply?

Code of Federal Regulations, 2014 CFR

2014-07-01

... implementation plan designed to meet one or more objectives. An activity is a part of a project and has its own... or improved programs and services, beyond those regularly budgeted, specifically designed to improve... expended by an institution of higher education for instruction, research, public service, academic support...

34 CFR 607.7 - What definitions apply?

Code of Federal Regulations, 2010 CFR

2010-07-01

... incorporated into an implementation plan designed to meet one or more objectives. An activity is a part of a..., specifically designed to improve the self sufficiency of the school. Educational and general expenditures means the total amount expended by an institution of higher education for instruction, research, public...

34 CFR 607.7 - What definitions apply?

Code of Federal Regulations, 2014 CFR

2014-07-01

... incorporated into an implementation plan designed to meet one or more objectives. An activity is a part of a..., specifically designed to improve the self sufficiency of the school. Educational and general expenditures means the total amount expended by an institution of higher education for instruction, research, public...

34 CFR 607.7 - What definitions apply?

Code of Federal Regulations, 2011 CFR

2011-07-01

... incorporated into an implementation plan designed to meet one or more objectives. An activity is a part of a..., specifically designed to improve the self sufficiency of the school. Educational and general expenditures means the total amount expended by an institution of higher education for instruction, research, public...

34 CFR 606.7 - What definitions apply?

Code of Federal Regulations, 2011 CFR

2011-07-01

... implementation plan designed to meet one or more objectives. An activity is a part of a project and has its own... or improved programs and services, beyond those regularly budgeted, specifically designed to improve... expended by an institution of higher education for instruction, research, public service, academic support...

34 CFR 606.7 - What definitions apply?

Code of Federal Regulations, 2010 CFR

2010-07-01

... implementation plan designed to meet one or more objectives. An activity is a part of a project and has its own... or improved programs and services, beyond those regularly budgeted, specifically designed to improve... expended by an institution of higher education for instruction, research, public service, academic support...

Solid state, S-band, power amplifier

NASA Technical Reports Server (NTRS)

Digrindakis, M.

1973-01-01

The final design and specifications for a solid state, S-band, power amplifier is reported. Modifications from a previously proposed design were incorporated to improve efficiency and meet input overdrive and noise floor requirements. Reports on the system design, driver amplifier, power amplifier, and voltage and current limiter are included along with a discussion of the testing program.

Application of theory to propeller design

NASA Technical Reports Server (NTRS)

Cox, G. G.; Morgan, W. B.

1974-01-01

The various theories concerning propeller design are discussed. The use of digital computers to obtain specific blade shapes to meet appropriate flow conditions is emphasized. The development of lifting-line and lifting surface configurations is analyzed. Ship propulsive performance and basic propeller design considerations are investigated. The characteristics of supercavitating propellers are compared with those of subcavitating propellers.

40 CFR Appendix A - Protocol for Using an Electrochemical Analyzer to Determine Oxygen and Carbon Monoxide...

Code of Federal Regulations, 2014 CFR

2014-07-01

..., and Process Heaters Using Portable Analyzers”, EMC Conditional Test Protocol 30 (CTM-30), Gas Research... cell design(s) conforming to this protocol will determine the analytical range for each gas component..., selective gas scrubbers, etc.) to meet the design specifications of this protocol. Do not make changes to...

40 CFR Appendix A - Protocol for Using an Electrochemical Analyzer to Determine Oxygen and Carbon Monoxide...

Code of Federal Regulations, 2013 CFR

2013-07-01

..., and Process Heaters Using Portable Analyzers”, EMC Conditional Test Protocol 30 (CTM-30), Gas Research... cell design(s) conforming to this protocol will determine the analytical range for each gas component..., selective gas scrubbers, etc.) to meet the design specifications of this protocol. Do not make changes to...

Techniques for designing rotorcraft control systems

NASA Technical Reports Server (NTRS)

Yudilevitch, Gil; Levine, William S.

1994-01-01

Over the last two and a half years we have been demonstrating a new methodology for the design of rotorcraft flight control systems (FCS) to meet handling qualities requirements. This method is based on multicriterion optimization as implemented in the optimization package CONSOL-OPTCAD (C-O). This package has been developed at the Institute for Systems Research (ISR) at the University of Maryland at College Park. This design methodology has been applied to the design of a FCS for the UH-60A helicopter in hover having the ADOCS control structure. The controller parameters have been optimized to meet the ADS-33C specifications. Furthermore, using this approach, an optimal (minimum control energy) controller has been obtained and trade-off studies have been performed.

WaterSense Labeled New Homes

EPA Pesticide Factsheets

Homes built to meet EPA's specification can earn the WaterSense label. EPA criteria include WaterSense labeled plumbing fixtures, efficient hot water delivery systems, water-smart landscape design, and other features.

78 FR 47217 - Proposed Supervisory Guidance on Implementing Dodd-Frank Act Company-Run Stress Tests for Banking...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-05

..., that are designed to ensure that its stress testing processes are effective in meeting the requirements... specific methodological practices. Consistent with this approach, this guidance sets general supervisory... use any specific methodological practices for their stress tests. Companies may use various practices...

VOCATIONAL EDUCATION INFORMATION SYSTEM. FINAL REPORT.

ERIC Educational Resources Information Center

ZWICKEL, I.; AND OTHERS

STATE- AND FEDERAL-LEVEL DESIGN SPECIFICATIONS WERE DEVELOPED FOR A SYSTEM CAPABLE OF COLLECTING AND REDUCING NATIONWIDE STATISTICAL DATA ON VOCATIONAL EDUCATION. THESE SPECIFICATIONS WERE EXPECTED TO PROVIDE THE BASIS FOR THE ADOPTION BY ALL STATES OF AN INFORMATION REPORTING SYSTEM THAT WOULD MEET BOTH PRESENT AND FUTURE FEDERAL REPORTING…

7 CFR 1728.70 - Procurement of materials.

Code of Federal Regulations, 2014 CFR

2014-01-01

... unlisted item in emergency situations and for experimental use or to meet a specific need. For purposes of... from the industry is not readily available, or the standard designs are not applicable to the borrower's specific problem under consideration. (3) RUS will make arrangements for test or experimental use...

7 CFR 1728.70 - Procurement of materials.

Code of Federal Regulations, 2012 CFR

2012-01-01

... unlisted item in emergency situations and for experimental use or to meet a specific need. For purposes of... from the industry is not readily available, or the standard designs are not applicable to the borrower's specific problem under consideration. (3) RUS will make arrangements for test or experimental use...

7 CFR 1728.70 - Procurement of materials.

Code of Federal Regulations, 2010 CFR

2010-01-01

... unlisted item in emergency situations and for experimental use or to meet a specific need. For purposes of... from the industry is not readily available, or the standard designs are not applicable to the borrower's specific problem under consideration. (3) RUS will make arrangements for test or experimental use...

7 CFR 1728.70 - Procurement of materials.

Code of Federal Regulations, 2013 CFR

2013-01-01

... unlisted item in emergency situations and for experimental use or to meet a specific need. For purposes of... from the industry is not readily available, or the standard designs are not applicable to the borrower's specific problem under consideration. (3) RUS will make arrangements for test or experimental use...

7 CFR 1728.70 - Procurement of materials.

Code of Federal Regulations, 2011 CFR

2011-01-01

... unlisted item in emergency situations and for experimental use or to meet a specific need. For purposes of... from the industry is not readily available, or the standard designs are not applicable to the borrower's specific problem under consideration. (3) RUS will make arrangements for test or experimental use...

49 CFR 178.346-1 - General requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Containers for Motor Vehicle Transportation § 178.346-1 General requirements. (a) Each Specification DOT 406 cargo tank motor vehicle must meet the general design and construction requirements in § 178.345, in addition to the specific requirements contained in this section. (b) MAWP: The MAWP of each cargo tank must...

49 CFR 178.346-1 - General requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Specifications for Containers for Motor Vehicle Transportation § 178.346-1 General requirements. (a) Each Specification DOT 406 cargo tank motor vehicle must meet the general design and construction requirements in... each cargo tank must be no lower than 2.65 psig and no higher than 4 psig. (c) Vacuum loaded cargo...

49 CFR 178.346-1 - General requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Containers for Motor Vehicle Transportation § 178.346-1 General requirements. (a) Each Specification DOT 406 cargo tank motor vehicle must meet the general design and construction requirements in § 178.345, in addition to the specific requirements contained in this section. (b) MAWP: The MAWP of each cargo tank must...

49 CFR 178.346-1 - General requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Containers for Motor Vehicle Transportation § 178.346-1 General requirements. (a) Each Specification DOT 406 cargo tank motor vehicle must meet the general design and construction requirements in § 178.345, in addition to the specific requirements contained in this section. (b) MAWP: The MAWP of each cargo tank must...

49 CFR 178.346-1 - General requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Containers for Motor Vehicle Transportation § 178.346-1 General requirements. (a) Each Specification DOT 406 cargo tank motor vehicle must meet the general design and construction requirements in § 178.345, in addition to the specific requirements contained in this section. (b) MAWP: The MAWP of each cargo tank must...

49 CFR 229.141 - Body structure, MU locomotives.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Body structure, MU locomotives. 229.141 Section... Design Requirements § 229.141 Body structure, MU locomotives. (a) MU locomotives built new after April 1... body structure designed to meet or exceed the following minimum specifications: (1) The body structure...

When "Less is More": The Optimal Design of Language Laboratory Hardware.

ERIC Educational Resources Information Center

Kershaw, Gary; Boyd, Gary

1980-01-01

The results of a process of designing, building, and "de-bugging" two replacement language laboratory hardware systems at Concordia University (Montreal) are described. Because commercially available systems did not meet specifications within budgetary constraints, the systems were built by the university technical department. The systems replaced…

Investigation of a family of power conditioners integrated into a utility grid: Category 1

NASA Astrophysics Data System (ADS)

Wood, P.; Putkovich, R. P.

1981-07-01

Technical issues regarding ac and dc interface requirements were studied. A baseline design was selected to be a good example of existing technology which would not need significant development effort for its implementation in residential solar photovoltaic systems. Alternative technologies are evaluated to determine which meet the baseline specification, and their costs and losses are evaluated. Areas in which cost improvements can be obtained are studied, and the three best candidate technologies--the current sourced converter, the HF front end converter, and the programmed wave converter--are compared. It is concluded that the designs investigated will meet, or with slight improvement could meet, short term efficiency goals. Long term efficiency goals could be met if an isolation transformer were not required in the power conditioning equipment. None of the technologies studied can meet cost goals unless further improvements are possible.

Specification for strontium-90 500-watt(e) radioisotopic thermoelectric generator

NASA Astrophysics Data System (ADS)

Hammel, T.; Himes, J.; Lieberman, A.; McGrew, J. W.; Owings, D.; Schumann, F.

1983-04-01

A conceptual design for a demonstration 500-watt(e) radioisotopic thermoelectric generator (RTG) was created. The design effort was divided into two tasks, viz., create a design specification for a capsule strenth member that utilizes a standard Strontium 90 fluoride filled WESF inner liner, and create a conceptual design for a 500-watt(e) RTG. The strength member specification was designed to survive an external pressure of 24,500 psi and meet the requirements of special form radioisotope heat sources. Therefore the capsule is if desired, licensed for domestic and international transport. The design for the RTG features a radioisotopic heat source, an array of nine capsules in a tungsten biological shield, four current technology series connected thermoelectric conversion modules, low conductivity thermal insulation, and a passive finned housing radiator for waste heat dissipation. The preliminary RTG specification formulated previous to contract award was met or exceeded.

Design and implementation of components for a bioregenerative system for growing higher order plants in space

NASA Technical Reports Server (NTRS)

Brakman, B.; Dioso, L.; Parker, D.; Segal, L.; Merriman, C.; Howard, I.; Vu, H.; Anderson, K.; Riley, S.; Amery, D.

1989-01-01

This report summarizes the efforts of the NASA/USRA Advanced Design Program during the 1988-89 scholastic year. The primary goal was to address specific needs in the design of an integrated system to grow higher order plants in space. The initial phase of the design effort concentrated on studying such a system and identifying its needs. Once these needs were defined, emphasis was placed on the design and fabrication of devices to meet them. Specific attention was placed on a hand-held harvester, a nutrient concentration sensor, an air-water separator, and a closed-loop biological system simulation.

A Fingerprint Pattern of Supports for Teachers' Designing of Technology-Enhanced Learning

ERIC Educational Resources Information Center

Svihla, Vanessa; Reeve, Richard; Sagy, Ornit; Kali, Yael

2015-01-01

Teachers often find themselves in a position in which they need to adapt technology-enhanced materials to meet the needs of their students. As new technologies--especially those not specifically designed for learning--find their way into schools, teachers need to be able to design learning experiences that use these new technologies in their local…

A New Capability for Nuclear Thermal Propulsion Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Amiri, Benjamin W.; Nuclear and Radiological Engineering Department, University of Florida, Gainesville, FL 32611; Kapernick, Richard J.

2007-01-30

This paper describes a new capability for Nuclear Thermal Propulsion (NTP) design that has been developed, and presents the results of some analyses performed with this design tool. The purpose of the tool is to design to specified mission and material limits, while maximizing system thrust to weight. The head end of the design tool utilizes the ROCket Engine Transient Simulation (ROCETS) code to generate a system design and system design requirements as inputs to the core analysis. ROCETS is a modular system level code which has been used extensively in the liquid rocket engine industry for many years. Themore » core design tool performs high-fidelity reactor core nuclear and thermal-hydraulic design analysis. At the heart of this process are two codes TMSS-NTP and NTPgen, which together greatly automate the analysis, providing the capability to rapidly produce designs that meet all specified requirements while minimizing mass. A PERL based command script, called CORE DESIGNER controls the execution of these two codes, and checks for convergence throughout the process. TMSS-NTP is executed first, to produce a suite of core designs that meet the specified reactor core mechanical, thermal-hydraulic and structural requirements. The suite of designs consists of a set of core layouts and, for each core layout specific designs that span a range of core fuel volumes. NTPgen generates MCNPX models for each of the core designs from TMSS-NTP. Iterative analyses are performed in NTPgen until a reactor design (fuel volume) is identified for each core layout that meets cold and hot operation reactivity requirements and that is zoned to meet a radial core power distribution requirement.« less

Comparative Evaluations of Four Specification Methods for Real-Time Systems

DTIC Science & Technology

1989-12-01

December 1989 Comparative Evaluations of Four Specification Methods for Real - Time Systems David P. Wood William G. Wood Specification and Design Methods...Methods for Real - Time Systems Abstract: A number of methods have been proposed in the last decade for the specification of system and software requirements...and software specification for real - time systems . Our process for the identification of methods that meet the above criteria is described in greater

76 FR 61350 - Environmental Management Site-Specific Advisory Board, Paducah

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-04

... Water Model. [cir] Presentation by Swift & Staley: Environmental Information Center. Subcommittee Chairs... in the agenda. The Deputy Designated Federal Officer is empowered to conduct the meeting in a fashion...

Energy efficient engine flight propulsion system preliminary analysis and design report

NASA Technical Reports Server (NTRS)

Gardner, W. B.

1979-01-01

A flight propulsion system preliminary design was established that meets the program goals of at least a 12 percent reduction in thrust specific fuel consumption, at least a five percent reduction in direct operating cost, and one-half the performance deterioration rate of the most efficient current commercial engines. The engine provides a high probability of meeting the 1978 noise rule goal. Smoke and gaseous emissions defined by the EPA proposed standards for engines newly certified after 1 January 1981 are met with the exception of NOx, despite incorporation of all known NOx reduction technology.

Integrated modeling tool for performance engineering of complex computer systems

NASA Technical Reports Server (NTRS)

Wright, Gary; Ball, Duane; Hoyt, Susan; Steele, Oscar

1989-01-01

This report summarizes Advanced System Technologies' accomplishments on the Phase 2 SBIR contract NAS7-995. The technical objectives of the report are: (1) to develop an evaluation version of a graphical, integrated modeling language according to the specification resulting from the Phase 2 research; and (2) to determine the degree to which the language meets its objectives by evaluating ease of use, utility of two sets of performance predictions, and the power of the language constructs. The technical approach followed to meet these objectives was to design, develop, and test an evaluation prototype of a graphical, performance prediction tool. The utility of the prototype was then evaluated by applying it to a variety of test cases found in the literature and in AST case histories. Numerous models were constructed and successfully tested. The major conclusion of this Phase 2 SBIR research and development effort is that complex, real-time computer systems can be specified in a non-procedural manner using combinations of icons, windows, menus, and dialogs. Such a specification technique provides an interface that system designers and architects find natural and easy to use. In addition, PEDESTAL's multiview approach provides system engineers with the capability to perform the trade-offs necessary to produce a design that meets timing performance requirements. Sample system designs analyzed during the development effort showed that models could be constructed in a fraction of the time required by non-visual system design capture tools.

Designing a leadership development program for surgeons.

PubMed

Jaffe, Gregory A; Pradarelli, Jason C; Lemak, Christy Harris; Mulholland, Michael W; Dimick, Justin B

2016-01-01

Although numerous leadership development programs (LDPs) exist in health care, no programs have been specifically designed to meet the needs of surgeons. This study aimed to elicit practicing surgeons' motivations and desired goals for leadership training to design an evidence-based LDP in surgery. At a large academic health center, we conducted semistructured interviews with 24 surgical faculty members who voluntarily applied and were selected for participation in a newly created LDP. Transcriptions of the interviews were analyzed using analyst triangulation and thematic coding to extract major themes regarding surgeons' motivations and perceived needs for leadership knowledge and skills. Themes from interview responses were then used to design the program curriculum specifically to meet the leadership needs of surgical faculty. Three major themes emerged regarding surgeons' motivations for seeking leadership training: (1) Recognizing key gaps in their formal preparation for leadership roles; (2) Exhibiting an appetite for personal self-improvement; and (3) Seeking leadership guidance for career advancement. Participants' interviews revealed four specific domains of knowledge and skills that they indicated as desired takeaways from a LDP: (1) leadership and communication; (2) team building; (3) business acumen/finance; and (4) greater understanding of the health care context. Interviews with surgical faculty members identified gaps in prior leadership training and demonstrated concrete motivations and specific goals for participating in a formal leadership program. A LDP that is specifically tailored to address the needs of surgical faculty may benefit surgeons at a personal and institutional level. Copyright © 2016 Elsevier Inc. All rights reserved.

13 CFR 121.701 - What SBIR programs are subject to size determinations?

Code of Federal Regulations, 2010 CFR

2010-01-01

... between any Federal agency and any small business for the performance of experimental, developmental, or... design, development, and improvement of prototypes and new processes to meet specific requirements. ...

13 CFR 121.701 - What SBIR programs are subject to size determinations?

Code of Federal Regulations, 2012 CFR

2012-01-01

... between any Federal agency and any small business for the performance of experimental, developmental, or... design, development, and improvement of prototypes and new processes to meet specific requirements. ...

13 CFR 121.701 - What SBIR programs are subject to size determinations?

Code of Federal Regulations, 2011 CFR

2011-01-01

... between any Federal agency and any small business for the performance of experimental, developmental, or... design, development, and improvement of prototypes and new processes to meet specific requirements. ...

75 FR 6370 - Environmental Management Site-Specific Advisory Board, Nevada

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-09

..., waste management, and related activities. Tentative Agenda 1. Presentation--History of the Nevada Test... agenda. The Deputy Designated Federal Officer is empowered to conduct the meeting in a fashion that will...

English for Specific Purposes and Academic Literacies: Eclecticism in Academic Writing Pedagogy

ERIC Educational Resources Information Center

McGrath, Lisa; Kaufhold, Kathrin

2016-01-01

Academic Literacies and English for Specific Purposes perspectives on the teaching of academic writing tend to be positioned as dichotomous and ideologically incompatible. Nonetheless, recent studies have called for the integration of these two perspectives in the design of writing programmes in order to meet the needs of students in the…

A CURRICULUM DESIGN FOR DISADVANTAGED COMMUNITY JUNIOR COLLEGE STUDENTS.

ERIC Educational Resources Information Center

CLARKE, JOHNNIE RUTH

THE JUNIOR COLLEGE MUST DEVELOP A CURRICULUM DESIGNED TO MEET THE IDENTIFIABLE EDUCATIONAL NEEDS OF THE DISADVANTAGED STUDENT, WITH SPECIFIC REFERENCE TO THE EFFECTS OF DEPRIVATION ON ASPIRATIONS, VALUES, MOTIVATION, AND SELF-CONCEPT AND TO THE INFLUENCE OF CLASS OR CASTE ON ACADEMIC PROGRESS. THIS STUDENT NEEDS TO DEVELOP (1) POSITIVE FEELINGS OF…

40 CFR 76.14 - Monitoring, recordkeeping, and reporting.

Code of Federal Regulations, 2011 CFR

2011-07-01

... NOX emission control system to the owner or operator showing that such system was designed to meet the... emission control system that were not included in the design specifications and performance guarantee, but... regard to the following types of Group 1, Phase I units: (i) Units employing no new NOX emission control...

40 CFR 76.14 - Monitoring, recordkeeping, and reporting.

Code of Federal Regulations, 2012 CFR

2012-07-01

... NOX emission control system to the owner or operator showing that such system was designed to meet the... emission control system that were not included in the design specifications and performance guarantee, but... regard to the following types of Group 1, Phase I units: (i) Units employing no new NOX emission control...

40 CFR 76.14 - Monitoring, recordkeeping, and reporting.

Code of Federal Regulations, 2010 CFR

2010-07-01

... NOX emission control system to the owner or operator showing that such system was designed to meet the... emission control system that were not included in the design specifications and performance guarantee, but... regard to the following types of Group 1, Phase I units: (i) Units employing no new NOX emission control...

40 CFR 76.14 - Monitoring, recordkeeping, and reporting.

Code of Federal Regulations, 2014 CFR

2014-07-01

... installed NOX emission control system to the owner or operator showing that such system was designed to meet... performance of the NOX emission control system that were not included in the design specifications and... control system during the demonstration period. The tests shall include tests in § 76.15, which may be...

40 CFR 76.14 - Monitoring, recordkeeping, and reporting.

Code of Federal Regulations, 2013 CFR

2013-07-01

... installed NOX emission control system to the owner or operator showing that such system was designed to meet... performance of the NOX emission control system that were not included in the design specifications and... control system during the demonstration period. The tests shall include tests in § 76.15, which may be...

Design options for a bunsen reactor.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moore, Robert Charles

2013-10-01

This work is being performed for Matt Channon Consulting as part of the Sandia National Laboratories New Mexico Small Business Assistance Program (NMSBA). Matt Channon Consulting has requested Sandia's assistance in the design of a chemical Bunsen reactor for the reaction of SO2, I2 and H2O to produce H2SO4 and HI with a SO2 feed rate to the reactor of 50 kg/hour. Based on this value, an assumed reactor efficiency of 33%, and kinetic data from the literature, a plug flow reactor approximately 1%E2%80%9D diameter and and 12 inches long would be needed to meet the specification of the project.more » Because the Bunsen reaction is exothermic, heat in the amount of approximately 128,000 kJ/hr would need to be removed using a cooling jacket placed around the tubular reactor. The available literature information on Bunsen reactor design and operation, certain support equipment needed for process operation and a design that meet the specification of Matt Channon Consulting are presented.« less

Meeting the Challenge of Installing Canes During New Ship Construction on LPD 28

DTIC Science & Technology

2015-03-01

components making up the SWAN are enclosed in Raytheon-designed hardware systems that meet Military Specification MIL-S-901D Grade B shock...Connected Connected Connected, NRE Connected, Engr Control Sys (ECS), Integrated to segreg; tte NREto Condition Assmt Sys (I CAS) SWAN develop HM&E...Hull Mecllanical & Electrical (HM&E) - COA Connected NA Connected Connected, NRE Connected, Damage Control Action Management Dependent to segreg; tte

Design verification of SIFT

NASA Technical Reports Server (NTRS)

Moser, Louise; Melliar-Smith, Michael; Schwartz, Richard

1987-01-01

A SIFT reliable aircraft control computer system, designed to meet the ultrahigh reliability required for safety critical flight control applications by use of processor replications and voting, was constructed for SRI, and delivered to NASA Langley for evaluation in the AIRLAB. To increase confidence in the reliability projections for SIFT, produced by a Markov reliability model, SRI constructed a formal specification, defining the meaning of reliability in the context of flight control. A further series of specifications defined, in increasing detail, the design of SIFT down to pre- and post-conditions on Pascal code procedures. Mechanically checked mathematical proofs were constructed to demonstrate that the more detailed design specifications for SIFT do indeed imply the formal reliability requirement. An additional specification defined some of the assumptions made about SIFT by the Markov model, and further proofs were constructed to show that these assumptions, as expressed by that specification, did indeed follow from the more detailed design specifications for SIFT. This report provides an outline of the methodology used for this hierarchical specification and proof, and describes the various specifications and proofs performed.

Preliminary design and analysis of an advanced rotorcraft transmission

NASA Technical Reports Server (NTRS)

Henry, Z. S.

1990-01-01

Future rotorcraft transmissions of the 1990s and beyond the year 2000 require the incorporation of key emerging material and component technologies using advanced and innovative design practices in order to meet the requirements for a reduced weight-to-power ratio, a decreased noise level, and a substantially increased reliability. The specific goals for future rotocraft transmissions when compared with current state-of-the-art transmissions are a 25 percent weight reduction, a 10-dB reduction in the transmitted noise level, and a system reliability of 5000 hours mean-time-between-removal for the transmission. This paper presents the results of the design studies conducted to meet the stated goals for an advanced rotorcraft transmission. These design studies include system configuration, planetary gear train selection, and reliability prediction methods.

Design Standards for Engineered Tissues

PubMed Central

Nawroth, Janna C.; Parker, Kevin Kit

2013-01-01

Traditional technologies are required to meet specific, quantitative standards of safety and performance. In tissue engineering, similar standards will have to be developed to enable routine clinical use and customized tissue fabrication. In this essay, we discuss a framework of concepts leading towards general design standards for tissue-engineering, focusing in particular on systematic design strategies, control of cell behavior, physiological scaling, fabrication modes and functional evaluation. PMID:23267860

Design of the Curriculum for a Second-Cycle Course in Civil Engineering in the Context of the Bologna Framework

ERIC Educational Resources Information Center

Gavin, K. G.

2010-01-01

This paper describes the design of the curriculum for a Master of Engineering programme in civil engineering at University College Dublin. The revised programme was established to meet the requirements of the Bologna process and this paper specifically considers the design of a new, second-cycle master's component of the programme. In addition to…

High Intensity Superconducting Cyclotron

DTIC Science & Technology

2012-12-01

currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. 1. REPORT DATE (DD-MM-YYYY) 2. REPORT TYPE 3. DATES COVERED...37   4.1   Magnetic  Design  with  Rare   Earth  Pole  Tips...performance meeting the specification. 4.0 Magnetic Field Design 4.1 Magnetic Design with Rare Earth Pole Tips At the time the project was

Silicon solar cells with a total power capacity of 30 kilowatts

NASA Technical Reports Server (NTRS)

1977-01-01

The bulk of the contract effort was carried out in the following two phases: Phase 1 -- module design, Pre-production module fabrication, inspection and test. Phase 2 -- Production, test and delivery. Effort during the first two months of the contract concentrated on design of a solar module to meet specification. Basic module design resulting from this effort is as follows: (1) frame design; (2) cell pan design; (3) cell interconnection; (4) encapsulation; (5) electrical performance.

User-centric design of a personal assistance robot (FRASIER) for active aging.

PubMed

Padir, Taşkin; Skorinko, Jeanine; Dimitrov, Velin

2015-01-01

We present our preliminary results from the design process for developing the Worcester Polytechnic Institute's personal assistance robot, FRASIER, as an intelligent service robot for enabling active aging. The robot capabilities include vision-based object detection, tracking the user and help with carrying heavy items such as grocery bags or cafeteria trays. This work-in-progress report outlines our motivation and approach to developing the next generation of service robots for the elderly. Our main contribution in this paper is the development of a set of specifications based on the adopted user-centered design process, and realization of the prototype system designed to meet these specifications.

Quantification of uncertainty in machining operations for on-machine acceptance.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Claudet, Andre A.; Tran, Hy D.; Su, Jiann-Chemg

2008-09-01

Manufactured parts are designed with acceptance tolerances, i.e. deviations from ideal design conditions, due to unavoidable errors in the manufacturing process. It is necessary to measure and evaluate the manufactured part, compared to the nominal design, to determine whether the part meets design specifications. The scope of this research project is dimensional acceptance of machined parts; specifically, parts machined using numerically controlled (NC, or also CNC for Computer Numerically Controlled) machines. In the design/build/accept cycle, the designer will specify both a nominal value, and an acceptable tolerance. As part of the typical design/build/accept business practice, it is required to verifymore » that the part did meet acceptable values prior to acceptance. Manufacturing cost must include not only raw materials and added labor, but also the cost of ensuring conformance to specifications. Ensuring conformance is a substantial portion of the cost of manufacturing. In this project, the costs of measurements were approximately 50% of the cost of the machined part. In production, cost of measurement would be smaller, but still a substantial proportion of manufacturing cost. The results of this research project will point to a science-based approach to reducing the cost of ensuring conformance to specifications. The approach that we take is to determine, a priori, how well a CNC machine can manufacture a particular geometry from stock. Based on the knowledge of the manufacturing process, we are then able to decide features which need further measurements from features which can be accepted 'as is' from the CNC. By calibration of the machine tool, and establishing a machining accuracy ratio, we can validate the ability of CNC to fabricate to a particular level of tolerance. This will eliminate the costs of checking for conformance for relatively large tolerances.« less

Automated iodine monitor system. [for aqueous solutions

NASA Technical Reports Server (NTRS)

1973-01-01

The feasibility of a direct spectrophotometric measurement of iodine in water was established. An iodine colorimeter, was built to demonstrate the practicality of this technique. The specificity of this method was verified when applied to an on-line system where a reference solution cannot be used, and a preliminary design is presented for an automated iodine measuring and controlling system meeting the desired specifications. An Automated iodine monitor/controller system based on this preliminary design was built, tested, and delivered to the Johnson Space Center.

Neglected Children: Suggestions for Early Childhood Educators.

ERIC Educational Resources Information Center

Peterson, Karen L.; Roscoe, Bruce

1983-01-01

Discusses enhancing the development and improving the quality of life of neglected children through acquiring a special understanding and style of interacting with them and by using activities designed specifically to meet their developmental needs. (RH)

75 FR 57462 - Environmental Management Site-Specific Advisory Board, Oak Ridge Reservation

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-21

... areas of environmental restoration, waste management, and related activities. Tentative Agenda: The main... agenda. The Deputy Designated Federal Officer is empowered to conduct the meeting in a fashion that will...

76 FR 9572 - Environmental Management Site-Specific Advisory Board, Oak Ridge Reservation

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-18

... areas of environmental restoration, waste management, and related activities. Tentative Agenda: The main... agenda. The Deputy Designated Federal Officer is empowered to conduct the meeting in a fashion that will...

75 FR 71424 - Environmental Management Site-Specific Advisory Board, Oak Ridge Reservation

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-23

... areas of environmental restoration, waste management, and related activities. Tentative Agenda: The main... Designated Federal Officer is empowered to conduct the meeting in a fashion that will facilitate the orderly...

Hooked on You.

ERIC Educational Resources Information Center

Sevier, Robert

1988-01-01

Most successful yield strategies use a series of messages specifically designed to meet the informational and emotional needs of students in the final decision-making stages. Techniques to try include: brochures, videotapes, handwritten postscripts, posters, and phone campaigns. (MLW)

76 FR 10018 - Environmental Management Site-Specific Advisory Board, Idaho National Laboratory

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-23

... Idaho's 2015 Cleanup Vision Government Budget Cycle American Recovery and Reinvestment Act Idaho Cleanup.... The Deputy Designated Federal Officer is empowered to conduct the meeting in a fashion that will...

Designing Interactive Multimedia Instruction to Address Soldiers’ Learning Needs

DTIC Science & Technology

2014-12-01

A point of need design seeks to identify and meet specific learning needs. It does so by focusing on the learning needs of an identified group ...instructional design and tailored training techniques to address the Army Learning Model (ALM) point of need concept. The point of need concept focuses both on ...developing six IMI exemplars focused on point of need training, including three variations of needs-focused designs : familiarization, core, and tailored

Specification and Design of Electrical Flight System Architectures with SysML

NASA Technical Reports Server (NTRS)

McKelvin, Mark L., Jr.; Jimenez, Alejandro

2012-01-01

Modern space flight systems are required to perform more complex functions than previous generations to support space missions. This demand is driving the trend to deploy more electronics to realize system functionality. The traditional approach for the specification, design, and deployment of electrical system architectures in space flight systems includes the use of informal definitions and descriptions that are often embedded within loosely coupled but highly interdependent design documents. Traditional methods become inefficient to cope with increasing system complexity, evolving requirements, and the ability to meet project budget and time constraints. Thus, there is a need for more rigorous methods to capture the relevant information about the electrical system architecture as the design evolves. In this work, we propose a model-centric approach to support the specification and design of electrical flight system architectures using the System Modeling Language (SysML). In our approach, we develop a domain specific language for specifying electrical system architectures, and we propose a design flow for the specification and design of electrical interfaces. Our approach is applied to a practical flight system.

High Energy Lithium-Ion VES Cells And Batteries Performances

NASA Astrophysics Data System (ADS)

Castric, A.-F.; Lawson, S.; Borthomieu, Y.

2011-10-01

b Saft's Space VES range of lithium-ion cells have been designed specifically to meet the satellites on-board power need, while meeting the legitimate high levels of requirements for space products. The purpose of the paper is to develop how the VES batteries designs have progressively evolved in order to accommodate the needs, requirements and constraints evolutions. The following topics will be presented: - Description of the main design features of the VES Li- ion batteries. - How the optimised battery configuration is selected against the required EOL power need or other constraints. - Presentation of the batteries performances (electrical, mechanical, thermal, interface, weight, ...). - Measures implemented in order to maintain these performances, and to guarantee the best product quality as per space standards.

Mastering the Diversity Challenge: Easy On-the-Job Applications for Measurable Results.

ERIC Educational Resources Information Center

Lebo, Fern

This book provides practical, step-by-step guidelines and gives important reasons why managing diversity is good for overall business. It identifies issues specific to designated groups and provides effective techniques for creating a level playing field, as well as specific on-the-job applications for running meetings, building a team, opening…

49 CFR 172.519 - General specifications for placards.

Code of Federal Regulations, 2011 CFR

2011-10-01

... meeting the specifications of this section which were in effect on October 1, 2001, (such as, a placard... 12.7 mm (0.5 inches) from each edge. (2) Except as otherwise provided in this subpart, the hazard... to the edge of the placard in the area designated on each placard except the color on the CORROSIVE...

49 CFR 172.519 - General specifications for placards.

Code of Federal Regulations, 2013 CFR

2013-10-01

... meeting the specifications of this section which were in effect on October 1, 2001, (such as, a placard... 12.7 mm (0.5 inches) from each edge. (2) Except as otherwise provided in this subpart, the hazard... to the edge of the placard in the area designated on each placard except the color on the CORROSIVE...

49 CFR 172.519 - General specifications for placards.

Code of Federal Regulations, 2014 CFR

2014-10-01

... meeting the specifications of this section which were in effect on October 1, 2001, (such as, a placard... 12.7 mm (0.5 inches) from each edge. (2) Except as otherwise provided in this subpart, the hazard... to the edge of the placard in the area designated on each placard except the color on the CORROSIVE...

49 CFR 172.519 - General specifications for placards.

Code of Federal Regulations, 2012 CFR

2012-10-01

... meeting the specifications of this section which were in effect on October 1, 2001, (such as, a placard... 12.7 mm (0.5 inches) from each edge. (2) Except as otherwise provided in this subpart, the hazard... to the edge of the placard in the area designated on each placard except the color on the CORROSIVE...

Medical Requirements for Ambulance Design and Equipment. Emergency Health Series.

ERIC Educational Resources Information Center

National Academy of Sciences - National Research Council, Washington, DC. Div. of Medical Sciences.

A vehicle must meet certain specific requirements to be classified as an ambulance if it is to satisfy the demands of the physician in terms of emergency care for which properly trained ambulance attendants can be held responsible. Developed by professional and lay experts for use by automotive designers and manufacturing, this publication would…

Composite Javelin

NASA Technical Reports Server (NTRS)

1979-01-01

In the photo at right, a unique, advanced type of javelin is undergoing "flight test." The javelin was designed to meet specifications laid down by the International Amateur Athletic Federation, but it has better stability than conventional javelins, according to college athletes who tested it. Its development incorporated aerodynamic design techniques and a composite material developed by NASA's Langley Research Center for aircraft and spacecraft.

Become an Indoor airPLUS Verifier

EPA Pesticide Factsheets

With the Indoor airPLUS Program, 3rd-party verifiers help ensure that EPA's high standards, based on leading building science, are applied by the builder during home design and construction to meet the Indoor airPLUS Construction Specifications.

Effects of aggregate angularity on mix design characteristics and pavement performance.

DOT National Transportation Integrated Search

2009-12-01

This research targeted two primary purposes: to estimate current aggregate angularity test methods and to evaluate current : aggregate angularity requirements in the Nebraska asphalt mixture/pavement specification. To meet the first research : object...

HOLLOTRON switch for megawatt lightweight space inverters

NASA Technical Reports Server (NTRS)

Poeschel, R. L.; Goebel, D. M.; Schumacher, R. W.

1991-01-01

The feasibility of satisfying the switching requirements for a megawatt ultralight inverter system using HOLLOTRON switch technology was determined. The existing experimental switch hardware was modified to investigate a coaxial HOLLOTRON switch configuration and the results were compared with those obtained for a modified linear HOLLOTRON configuration. It was concluded that scaling the HOLLOTRON switch to the current and voltage specifications required for a megawatt converter system is indeed feasible using a modified linear configuration. The experimental HOLLOTRON switch operated at parameters comparable to the scaled coaxial HOLLOTRON. However, the linear HOLLOTRON data verified the capability for meeting all the design objectives simultaneously including current density (greater than 2 A/sq cm), voltage (5 kV), switching frequency (20 kHz), switching time (300 ns), and forward voltage drop (less than or equal to 20 V). Scaling relations were determined and a preliminary design was completed for an engineering model linear HOLLOTRON switch to meet the megawatt converter system specifications.

Designing Flightdeck Procedures

NASA Technical Reports Server (NTRS)

Barshi, Immanuel; Mauro, Robert; Degani, Asaf; Loukopoulou, Loukia

2016-01-01

The primary goal of this document is to provide guidance on how to design, implement, and evaluate flight deck procedures. It provides a process for developing procedures that meet clear and specific requirements. This document provides a brief overview of: 1) the requirements for procedures, 2) a process for the design of procedures, and 3) a process for the design of checklists. The brief overview is followed by amplified procedures that follow the above steps and provide details for the proper design, implementation and evaluation of good flight deck procedures and checklists.

Designing a Leadership Development Program for Surgeons

PubMed Central

Jaffe, Gregory A.; Pradarelli, Jason C.; Lemak, Christy Harris; Mulholland, Michael W.; Dimick, Justin B.

2015-01-01

Background Although numerous leadership development programs exist in healthcare, no programs have been specifically designed to meet the needs of surgeons. This study aimed to elicit practicing surgeons’ motivations and desired goals for leadership training in order to design an evidence-based Leadership Development Program (LDP) in surgery. Materials and Methods At a large academic health center, we conducted semi-structured interviews with 24 surgical faculty members who voluntarily applied and were selected for participation in a newly created LDP. Transcriptions of the interviews were analyzed using analyst triangulation and thematic coding in order to extract major themes regarding surgeons’ motivations and perceived needs for leadership knowledge and skills. Themes from interview responses were then used to design the program curriculum specifically to meet the leadership needs of surgical faculty. Results Three major themes emerged regarding surgeons’ motivations for seeking leadership training: 1) Recognizing key gaps in their formal preparation for leadership roles; 2) Exhibiting an appetite for personal self-improvement; and 3) Seeking leadership guidance for career advancement. Participants’ interviews revealed four specific domains of knowledge and skills that they indicated as desired takeaways from a leadership development program: 1) leadership and communication; 2) team building; 3) business acumen/finance; and 4) greater understanding of the healthcare context. Conclusions Interviews with surgical faculty members identified gaps in prior leadership training and demonstrated concrete motivations and specific goals for participating in a formal leadership program. A Leadership Development Program that is specifically tailored to address the needs of surgical faculty may benefit surgeons at a personal and institutional level. PMID:26323368

The minicell TMirradiator: A new system for a new market

NASA Astrophysics Data System (ADS)

Clouser, James F.; Beers, Eric W.

1998-06-01

Since the commissioning of the first industrial Gamma Irradiator design, designers and operators of irradiation systems have been attempting to meet the specific production requirements and challenges presented to them. This objective has resulted in many different versions of irradiators currently in service today, all of which had original charters and many of which still perform very well within even the new requirements of this industry. Continuing changes in the marketplace have, however, placed pressures on existing designs due to a combination of changing dose requirements for sterlization, increased economic pressures from the specific industry served for both time and location and the increasing variety of product types requiring processing. Additionally, certain market areas which could never economically support a typical gamma processing facility have either not been serviced, or have forced potential gamma users to transport product long distances to one of these existing facilities. The MiniCell TM removes many of the traditional barriers previously accepted in the radiation processing industry for building a processing facility in a location. Its reduced size and cost have allowed many potential users to consider in-house processing and its ability to be quickly assembled allow it to meet market needs in a much more timely fashion than the previous designs. The MiniCell system can cost effectively meet many of the current market needs of reducing total cost of processing and also be flexible enough to process product in a wide range of industries effectively.

Ada Software Design Methods Formulation.

DTIC Science & Technology

1982-10-01

aside for one-to-one, non -judgemental discussions between SofTech and the design teams. SofTech’s role in the meetings was to address any Ada-specific...assurance 1.0 prepare version audits 1.0 monitoring contracts 1.0 library control 1.0 other development 1.0 correspondence 1.0 conduct support design ...quality assurance 2.0 Control Board update training manuals 2.0 participation 2.5 being trained 2.0 formulation of policy 2.5 functional system design

EVA Suit R and D for Performance Optimization

NASA Technical Reports Server (NTRS)

Cowley, Matthew S.; Harvill, Lauren; Benson, Elizabeth; Rajulu, Sudhakar

2014-01-01

Designing a planetary suit is very complex and often requires difficult trade-offs between performance, cost, mass, and system complexity. To verify that new suit designs meet requirements, full prototypes must be built and tested with human subjects. However, numerous design iterations will occur before the hardware meets those requirements. Traditional draw-prototype-test paradigms for R&D are prohibitively expensive with today's shrinking Government budgets. Personnel at NASA are developing modern simulation techniques which focus on human-centric designs by creating virtual prototype simulations and fully adjustable physical prototypes of suit hardware. During the R&D design phase, these easily modifiable representations of an EVA suit's hard components will allow designers to think creatively and exhaust design possibilities before they build and test working prototypes with human subjects. It allows scientists to comprehensively benchmark current suit capabilities and limitations for existing suit sizes and sizes that do not exist. This is extremely advantageous and enables comprehensive design down-selections to be made early in the design process, enables the use of human performance as design criteria, and enables designs to target specific populations

Adverse Outcome Pathways: From Definition to Application

EPA Science Inventory

A challenge for both human health and ecological toxicologists is the transparent application of mechanistic (e.g., molecular, biochemical, histological) data to risk assessments. The adverse outcome pathway (AOP) is a conceptual framework designed to meet this need. Specifical...

Sensor Network Middleware for Cyber-Physical Systems: Opportunities and Challenges

NASA Astrophysics Data System (ADS)

Singh, G.

2015-12-01

Wireless Sensor Network middleware typically provides abstractions for common tasks such as atomicity, synchronization and communication with the intention of isolating the developers of distributed applications from lower-level details of the underlying platforms. Developing middleware to meet the performance constraints of applications is an important challenge. Although one would like to develop generic middleware services which can be used in a variety of different applications, efficiency considerations often force developers to design middleware and algorithms customized to specific operational contexts. This presentation will discuss techniques to design middleware that is customizable to suit the performance needs of specific applications. We also discuss the challenges poised in designing middleware for pervasive sensor networks and cyber-physical systems with specific focus on environmental monitoring.

Passing the Baton: A Collaborative Approach to Development and Implementation of Context-Specific Modules for Graduate Teaching Assistants in Cognate Disciplines

ERIC Educational Resources Information Center

O'Neill, Geraldine; McNamara, Martin

2016-01-01

A systematic approach to the training of graduate teaching assistants (GTAs) is required to meet the challenges posed by growing numbers of undergraduate and graduate students. At University College Dublin, educational developers and academic staff across six schools collaborated on the design and phased implementation of context-specific GTA…

Software Architecture: Managing Design for Achieving Warfighter Capability

DTIC Science & Technology

2007-04-30

The Government’s requirements and specifications for a new weapon...at the Preliminary Design Review (PDR) is likely to have a much higher probability of meeting the warfighters’ need for capability. Test -case...inventories of test cases are developed from the user-defined scenarios so that there is one or more test case for every scenario. The test cases will

Study of solid rocket motors for a space shuttle booster. Volume 2 book 2: Supporting research and technology

NASA Technical Reports Server (NTRS)

Vonderesch, A. H.

1972-01-01

The baseline SRM design for the space shuttle employs proven technology based on actual motor firings. Supporting research and technology are therefore required only to address system technology that is specific to the shuttle requirements, and that is needed for optimization of design features. Eight programs are recommended to meet these requirements.

Strategic Planning for Community Viability: A Process, Not a Destination. Circular CRD-60.

ERIC Educational Resources Information Center

Albertson-Zenor, Patricia; Raftery, Sue

Strategic planning (SP), which has been used since the 1960s by business and industry, is now being used by schools, municipalities, universities, and even churches. SP is a process designed to assist groups in developing a custom-designed plan to meet the specific needs of their own organization or community. The following are five important…

The Utility of Needs Analysis for Nondomain Expert Instructors in Designing Task-Based Spanish for the Professions Curricula

ERIC Educational Resources Information Center

Serafini, Ellen J.; Torres, Julio

2015-01-01

The demand for Spanish for specific purposes (SSP) university courses in the United States has prompted widespread curricular change in language departments over the last two decades (Klee, 2015; Sánchez-López, 2013). However, many instructors lack the tools and training needed to design SSP curricula that meet learners' communicative needs in…

Universal Design for Learning in the Classroom: Practical Applications. What Works for Special-Needs Learners Series

ERIC Educational Resources Information Center

Hall, Tracey E., Ed.; Meyer, Anne, Ed.; Rose, David H., Ed.

2012-01-01

Clearly written and well organized, this book shows how to apply the principles of universal design for learning (UDL) across all subject areas and grade levels. The editors and contributors describe practical ways to develop classroom goals, assessments, materials, and methods that use UDL to meet the needs of all learners. Specific teaching…

High subsonic flow tests of a parallel pipe followed by a large area ratio diffuser

NASA Technical Reports Server (NTRS)

Barna, P. S.

1975-01-01

Experiments were performed on a pilot model duct system in order to explore its aerodynamic characteristics. The model was scaled from a design projected for the high speed operation mode of the Aircraft Noise Reduction Laboratory. The test results show that the model performed satisfactorily and therefore the projected design will most likely meet the specifications.

Ride quality criteria and the design process. [standards for ride comfort

NASA Technical Reports Server (NTRS)

Ravera, R. J.

1975-01-01

Conceptual designs for advanced ground transportation systems often hinge on obtaining acceptable vehicle ride quality while attempting to keep the total guideway cost (initial and subsequent maintenance) as low as possible. Two ride quality standards used extensively in work sponsored by the U.S. Department of Transportation (DOT) are the DOT-Urban Tracked Air Cushion Vehicle (UTACV) standard and the International Standards Organization (ISO) reduced ride comfort criteria. These standards are reviewed and some of the deficiencies, which become apparent when trying to apply them in practice, are noted. Through the use of a digital simulation, the impact of each of these standards on an example design process is examined. It is shown that meeting the ISO specification for the particular vehicle/guideway case investigated is easier than meeting the UTACV standard.

Evolution and Development of Effective Feedstock Specifications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garold Gresham; Rachel Emerson; Amber Hoover

The U.S. Department of Energy promotes the production of a range of liquid fuels and fuel blend stocks from lignocellulosic biomass feedstocks by funding fundamental and applied research that advances the state of technology in biomass collection, conversion, and sustainability. As part of its involvement in this program, the Idaho National Laboratory (INL) investigates the feedstock logistics economics and sustainability of these fuels. The 2012 feedstock logistics milestone demonstrated that for high-yield areas that minimize the transportation distances of a low-density, unstable biomass, we could achieve a delivered cost of $35/ton. Based on current conventional equipment and processes, the 2012more » logistics design is able to deliver the volume of biomass needed to fulfill the 2012 Renewable Fuel Standard’s targets for ethanol. However, the Renewable Fuel Standard’s volume targets are continuing to increase and are expected to peak in 2022 at 36 billion gallons. Meeting these volume targets and achieving a national-scale biofuels industry will require expansion of production capacity beyond the 2012 Conventional Feedstock Supply Design Case to access diverse available feedstocks, regardless of their inherent ability to meet preliminary biorefinery quality feedstock specifications. Implementation of quality specifications (specs), as outlined in the 2017 Design Case – “Feedstock Supply System Design and Economics for Conversion of Lignocellulosic Biomass to Hydrocarbon Fuels” (in progress), requires insertion of deliberate, active quality controls into the feedstock supply chain, whereas the 2012 Conventional Design only utilizes passive quality controls.« less

Variable speed gas engine-driven air compressor system

NASA Astrophysics Data System (ADS)

Morgan, J. R.; Ruggles, A. E.; Chen, T. N.; Gehret, J.

1992-11-01

Tecogen Inc. and Ingersoll-Rand Co. as a subcontractor have designed a nominal 150-hp gas engine-driven air compressor utilizing the TECODRIVE 8000 engine and the Ingersoll-Rand 178.5-mm twin screw compressor. Phase 1 included the system engineering and design, economic and applications studies, and a draft commercialization plan. Phase 2 included controls development, laboratory prototype construction, and performance testing. The testing conducted verified that the compressor meets all design specifications.

Sonar Transducer Reliability Improvement Program (STRIP) FY81.

DTIC Science & Technology

1981-10-01

that must be considered when selecting a material for the design of a sonar transducer. In the past decade, plastics have decreased in cost and...required in a sonar transducer system. A recent example of this type of failure has been with a neoprene .tfer formulation which was designed to meet...subject of the first design specification for transducer elastomers. Previous work on this material under the aegis of the Sonar Transduction

Enhancing the incorporation of the patient's voice in drug development and evaluation.

PubMed

Chalasani, Meghana; Vaidya, Pujita; Mullin, Theresa

2018-01-01

People living with a condition are uniquely positioned to inform the understanding of the therapeutic context for drug development and evaluation. In 2012, the U.S. Food and Drug Administration (FDA) established the Patient-Focused Drug Development (PFDD) initiative to more systematically obtain the patient perspective on specific diseases and their currently available treatments. PFDD meetings are unique among FDA public meetings, with a format designed to engage patients and elicit their perspectives on two topic areas: (1) the most significant symptoms of their condition and the impact of the condition on daily life; and, (2) their current approaches to treatment. FDA has conducted 24 disease-specific PFDD meetings to date. The lessons learned from PFDD meetings range from experiences common across rare diseases to more disease specific experiences that matter most to patients. FDA recognizes that FDA-led PFDD meetings alone cannot address the gaps in information on the patient perspective. Patient-focused drug development is an ongoing effort and FDA looks forward to the next steps in advancing the science and the utilization of patient input throughout drug development and evaluation. The U.S. Food and Drug Administration (FDA) has multiple mechanisms for its regulators and staff to interact with patients -- but none quite like its novel Patient-Focused Drug Development (PFDD) initiative. FDA established the PFDD initiative to more systematically obtain the patient perspective on specific diseases and their currently available treatments. Since the initiative's inception in 2012, FDA has held 24 PFDD meetings, covering a range of disease areas and hearing directly from thousands of patients and caregivers. FDA's PFDD meetings have also provided key stakeholders, including patient advocates, researchers, drug developers, healthcare providers, and other government officials, an opportunity to hear the patient's voice. The lessons learned include but are not limited to specific experiences that matter most to patients, patient perspectives on meaningful treatment benefits and how patients want to be engaged in the drug development process. FDA recognizes that FDA-led PFDD meetings alone cannot address the gaps in information on the patient perspective. Further enhancing the incorporation of the patient's voice in drug development and evaluation continues to be a priority for FDA.

The latency validation of the optical link for the ATLAS Liquid Argon Calorimeter Phase-I trigger upgrade

NASA Astrophysics Data System (ADS)

Deng, B.; Xiao, L.; Zhao, X.; Baker, E.; Gong, D.; Guo, D.; He, H.; Hou, S.; Liu, C.; Liu, T.; Sun, Q.; Thomas, J.; Wang, J.; Xiang, A. C.; Yang, D.; Ye, J.; Zhou, W.

2018-05-01

Two optical data link data transmission Application Specific Integrated Circuits (ASICs), the baseline and its backup, have been designed for the ATLAS Liquid Argon (LAr) Calorimeter Phase-I trigger upgrade. The latency of each ASIC and that of its corresponding receiver implemented in a back-end Field-Programmable Gate Array (FPGA) are critical specifications. In this paper, we present the latency measurements and simulation of two ASICs. The measurement results indicate that both ASICs achieve their design goals and meet the latency specifications. The consistency between the simulation and measurements validates the ASIC latency characterization.

Data Validation in the AEDC Engine Test Facility

DTIC Science & Technology

2010-02-01

25 3.4.1 Pretest ...25 3.4.2 Test Period .............................................................................................. 26 3.4.3 Posttest ...use of the data is to assess the degree to which the engine meets its design intent or its specification requirements. When engine development or

46 CFR 162.060-20 - Design and construction requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Ballast Water Management Systems... service; (4) Meets recognized national or international standards for all related marine engineering and electrical engineering applications; and (5) Operates when the vessel is upright, inclined under static...

46 CFR 162.060-20 - Design and construction requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Ballast Water Management Systems... service; (4) Meets recognized national or international standards for all related marine engineering and electrical engineering applications; and (5) Operates when the vessel is upright, inclined under static...

46 CFR 162.060-20 - Design and construction requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Ballast Water Management Systems... service; (4) Meets recognized national or international standards for all related marine engineering and electrical engineering applications; and (5) Operates when the vessel is upright, inclined under static...

EXPERIENCES IN DESIGNING SOLVENTS FOR THE ENVIRONMENT

EPA Science Inventory

Solvents used throughout industry are chosen to meet specific technological requirements such as solute solubility, cleaning and degreasing, or being a medium for paints and coatings. With the increasing awareness of the human health effects and environmental risks of solvent use...

EXPERIENCES IN DESIGNING SOLVENTS FOR THE ENVIRONMENT

EPA Science Inventory

Solvents used throughout industry are chosen to meet specific technological requirements such as solute solubility, cleaning and degreasing, or being a medium for paints and coatings. With the increasing awareness of the human health effects and environmental tisks of solvent use...

Performance and Life Tests of a Regenerative Blower for EVA Suit Ventilation

NASA Technical Reports Server (NTRS)

Izenson, Michael G.; Chen, Weibo; McCormick, John; Paul, Heather L.; Jennings, Mallory A.

2012-01-01

Ventilation fans for future space suits must meet demanding performance specifications, satisfy stringent safety requirements for operation in an oxygen atmosphere, and be able to increase output to operate in buddy mode. A regenerative blower is an attractive choice due to its ability to meet these requirements at low operating speed. This paper describes progress in the development and testing of a regenerative blower designed to meet requirements for ventilation subsystems in future space suits. The blower includes a custom-designed motor that has significantly improved its efficiency. We have measured the blower s head/flow performance and power consumption under conditions that simulate both the normal and buddy mode operating points. We have operated the blower for TBD hours and demonstrated safe operation in an oxygen test loop at prototypical pressures. We also demonstrated operation with simulated lunar dust.

Performance and Life Tests of a Regenerative Blower for EVA Suit Ventilation

NASA Technical Reports Server (NTRS)

Izenson, Mike; Chen, Weibo; Paul, Heather L.; Jennings, Mallory A.

2011-01-01

Ventilation fans for future space suits must meet demanding performance specifications, satisfy stringent safety requirements for operation in an oxygen atmosphere, and be able to increase output to operate in buddy mode. A regenerative blower is an attractive choice due to its ability to meet these requirements at low operating speed. This paper describes progress in the development and testing of a regenerative blower designed to meet requirements for ventilation subsystems in a future space suit Portable Life Support Systems (PLSS). The blower assembly includes a custom-designed motor that has significantly improved in efficiency during this development effort. The blower was tested at both nominal and buddy mode operating points and head/flow performance and power consumption were measured. The blower was operated for over 1000 hours to demonstrate safe operation in an oxygen test loop at prototypical pressures. In addition, the blower demonstrated operation with the introduction of simulated lunar dust.

An Analysis of an Automatic Coolant Bypass in the International Space Station Node 2 Internal Active Thermal Control System

NASA Technical Reports Server (NTRS)

Clanton, Stephen E.; Holt, James M.; Turner, Larry D. (Technical Monitor)

2001-01-01

A challenging part of International Space Station (ISS) thermal control design is the ability to incorporate design changes into an integrated system without negatively impacting performance. The challenge presents itself in that the typical ISS Internal Active Thermal Control System (IATCS) consists of an integrated hardware/software system that provides active coolant resources to a variety of users. Software algorithms control the IATCS to specific temperatures, flow rates, and pressure differentials in order to meet the user-defined requirements. What may seem to be small design changes imposed on the system may in fact result in system instability or the temporary inability to meet user requirements. The purpose of this paper is to provide a brief description of the solution process and analyses used to implement one such design change that required the incorporation of an automatic coolant bypass in the ISS Node 2 element.

Systems integrated human engineering on the Navy's rapid acquisition of manufactured parts/test and integration facility

NASA Technical Reports Server (NTRS)

Gallaway, Glen R.

1987-01-01

Human Engineering in many projects is at best a limited support function. In this Navy project the Human Engineering function is an integral component of the systems design and development process. Human Engineering is a member of the systems design organization. This ensures that people considerations are: (1) identified early in the project; (2) accounted for in the specifications; (3) incorporated into the design; and (4) the tested product meets the needs and expectations of the people while meeting the overall systems requirements. The project exemplifies achievements that can be made by the symbiosis between systems designers, engineers and Human Engineering. This approach increases Human Engineering's effectiveness and value to a project because it becomes an accepted, contributing team member. It is an approach to doing Human Engineering that should be considered for most projects. The functional and organizational issues giving this approach strength are described.

Design of a recumbent seating system

NASA Technical Reports Server (NTRS)

Croyle, Scott; Delarosa, Jose; George, Daren; Hinkle, Cathy; Karas, Stephen

1993-01-01

Future space shuttle missions presented by NASA might require the shuttle to rendezvous with the Russian space station Mir for the purpose of transporting astronauts back to earth. Due to the atrophied state of these astronauts, a special seating system must be designed for their transportation. The main functions of this seating system are to support and restrain the astronauts during normal reentry flight and to dampen some of the loading that might occur in a crash situation. Through research, the design team developed many concept variants for these functional requirements. By evaluating each variant, the concepts were eliminated until the four most attractive designs remained. The team used a decision matrix to determine the best concept to carry through embodiment. This concept involved using struts for support during reentry flight and a spring damper/shock absorber system to dampen crash landing loads. The embodiment design process consisted of defining the layout of each of the main functional components, specifically, the seat structure and the strut structure. Through the use of MCS/pal two, the design was refined until it could handle all required loads and dampen to the forces specified. The auxiliary function carriers were then considered. Following the design of these components, the complete final layout could be determined. It is concluded that the final design meets all specifications outlined in the conceptual design. The main advantages of this design are its low weight, simplicity, and large amount of function sharing between different components. The disassembly of this design could potentially present a problem because of time and size constraints involved. Overall, this design meets or exceeds all functional requirements.

Development of flame-resistant structures for use in the Apollo and Skylab programs

NASA Technical Reports Server (NTRS)

Coskren, R. J.

1973-01-01

Flame-resistant materials have been designed and fabricated to meet certain end-use criteria established by NASA with emphasis on meeting established flammability standards. The program had three general phases: (1) fabrication of candidate sample structures for evaluation by the Structures and Mechanics Division and/or NASA contractors; (2) physical testing of the structures developed; and (3) supply of required quantities of specific items for fabrication into prototype and/or flight items for the Apollo and Skylab programs.

76 FR 75435 - Fatigue Tolerance Evaluation of Metallic Structures

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-02

..., Regulations and Policy Group, Rotorcraft Directorate, ASW-111, Federal Aviation Administration, 2601 Meacham... designed and manufactured, performs properly, and meets the regulations and minimum standards prescribed... amended rule requires a specific result (that is, inspection, retirement times, or equivalent means to...

REAL TIME CONTROL OF URBAN DRAINAGE NETWORKS

EPA Science Inventory

Real-time control (RTC) is a custom-designed, computer-assisted management technology for a specific sewerage network to meet the operational objectives of its collection/conveyance system. RTC can operate in several modes, including a mode that is activated during a wet weather ...

Friendly Extensible Transfer Tool Beta Version

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collins, William P.; Gutierrez, Kenneth M.; McRee, Susan R.

2016-04-15

Often data transfer software is designed to meet specific requirements or apply to specific environments. Frequently, this requires source code integration for added functionality. An extensible data transfer framework is needed to more easily incorporate new capabilities, in modular fashion. Using FrETT framework, functionality may be incorporated (in many cases without need of source code) to handle new platform capabilities: I/O methods (e.g., platform specific data access), network transport methods, data processing (e.g., data compression.).

NASA Space Flight Human System Standards

NASA Technical Reports Server (NTRS)

Tillman, Barry; Pickett, Lynn; Russo, Dane; Stroud, Ken; Connolly, Jan; Foley, Tico

2007-01-01

NASA has begun a new approach to human factors design standards. For years NASA-STD-3000, Manned Systems Integration Standards, has been a source of human factors design guidance for space systems. In order to better meet the needs of the system developers, NASA is revising its human factors standards system. NASA-STD-3000 will be replaced by two documents: set of broad human systems specifications (including both human factors and medical topics) and a human factors design handbook

Charge-coupled device image sensor study

NASA Technical Reports Server (NTRS)

1973-01-01

The design specifications and predicted performance characteristics of a Charge-Coupled Device Area Imager and a Charge-Coupled Device Linear Imager are presented. The Imagers recommended are intended for use in space-borne imaging systems and therefore would meet the requirements for the intended application. A unique overlapping metal electrode structure and a buried channel structure are described. Reasons for the particular imager designs are discussed.

Formal specification and mechanical verification of SIFT - A fault-tolerant flight control system

NASA Technical Reports Server (NTRS)

Melliar-Smith, P. M.; Schwartz, R. L.

1982-01-01

The paper describes the methodology being employed to demonstrate rigorously that the SIFT (software-implemented fault-tolerant) computer meets its requirements. The methodology uses a hierarchy of design specifications, expressed in the mathematical domain of multisorted first-order predicate calculus. The most abstract of these, from which almost all details of mechanization have been removed, represents the requirements on the system for reliability and intended functionality. Successive specifications in the hierarchy add design and implementation detail until the PASCAL programs implementing the SIFT executive are reached. A formal proof that a SIFT system in a 'safe' state operates correctly despite the presence of arbitrary faults has been completed all the way from the most abstract specifications to the PASCAL program.

Investigation of a family of power conditioners integrated into a utility grid: final report Category I

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wood, P.; Putkovich, R.P.

1981-07-01

A study was conducted of the requirements for and technologies applicable to power conditioning equipment in residential solar photovoltaic systems. A survey of companies known or thought to manufacture power conditioning equipment was conducted to asses the technology. Technical issues regarding ac and dc interface requirements were studied. A baseline design was selected to be a good example of existing technology which would not need significant development effort for its implementation. Alternative technologies are evaluated to determine which meet the baseline specification, and their costs and losses are evaluated. Areas in which cost improvements can be obtained are studied, andmore » the three best candidate technologies--the current-sourced converter, the HF front end converter, and the programmed wave converter--are compared. It is concluded that the designs investigated will meet, or with slight improvement could meet, short term efficiency goals. Long term efficiency goals could be met if an isolation transformer were not required in the power conditioning equipment. None of the technologies studied can meet cost goals unless further improvements are possible. (LEW)« less

Why an Eye Limiting Display Resolution Matters

NASA Technical Reports Server (NTRS)

Kato, Kenji Hiroshi

2013-01-01

Many factors affect the suitability of an out-the-window simulator visual system. Contrast, brightness, resolution, field-of-view, update rate, scene content and a number of other criteria are common factors often used to define requirements for simulator visual systems. For the past 7 years, NASA has worked with the USAF on the Operational Based Vision Assessment Program. The purpose of this program has been to provide the USAF School of Aerospace Medicine with a scientific testing laboratory to study human vision and testing standards in an operationally relevant environment. It was determined early in the design that current commercial and military training systems wern't well suited for the available budget as well as the highly research oriented requirements. During various design review meetings, it was determined the OBVA requirements were best met by using commercial-off-the-shelf equipment to minimize technical risk and costs. In this paper we will describe how the simulator specifications were developed in order to meet the research objectives and the resulting architecture and design considerations. In particular we will discuss the image generator architecture and database developments to meet eye limited resolution.

Behavioral Attitudes and Preferences in Cooking Practices with Traditional Open-Fire Stoves in Peru, Nepal, and Kenya: Implications for Improved Cookstove Interventions

PubMed Central

Rhodes, Evelyn L.; Dreibelbis, Robert; Klasen, Elizabeth; Naithani, Neha; Baliddawa, Joyce; Menya, Diana; Khatry, Subarna; Levy, Stephanie; Tielsch, James M.; Miranda, J. Jaime; Kennedy, Caitlin; Checkley, William

2014-01-01

Global efforts are underway to develop and promote improved cookstoves which may reduce the negative health and environmental effects of burning solid fuels on health and the environment. Behavioral studies have considered cookstove user practices, needs and preferences in the design and implementation of cookstove projects; however, these studies have not examined the implications of the traditional stove use and design across multiple resource-poor settings in the implementation and promotion of improved cookstove projects that utilize a single, standardized stove design. We conducted in-depth interviews and direct observations of meal preparation and traditional, open-fire stove use of 137 women aged 20–49 years in Kenya, Peru and Nepal prior in the four-month period preceding installation of an improved cookstove as part of a field intervention trial. Despite general similarities in cooking practices across sites, we identified locally distinct practices and norms regarding traditional stove use and desired stove improvements. Traditional stoves are designed to accommodate specific cooking styles, types of fuel, and available resources for maintenance and renovation. The tailored stoves allow users to cook and repair their stoves easily. Women in each setting expressed their desire for a new stove, but they articulated distinct specific alterations that would meet their needs and preferences. Improved cookstove designs need to consider the diversity of values and needs held by potential users, presenting a significant challenge in identifying a “one size fits all” improved cookstove design. Our data show that a single stove design for use with locally available biomass fuels will not meet the cooking demands and resources available across the three sites. Moreover, locally produced or adapted improved cookstoves may be needed to meet the cooking needs of diverse populations while addressing health and environmental concerns of traditional stoves. PMID:25286166

What is the evidence for conducting palliative care family meetings? A systematic review.

PubMed

Cahill, Philippa J; Lobb, Elizabeth A; Sanderson, Christine; Phillips, Jane L

2017-03-01

Structured family meeting procedures and guidelines suggest that these forums enhance family-patient-team communication in the palliative care inpatient setting. However, the vulnerability of palliative patients and the resources required to implement family meetings in accordance with recommended guidelines make better understanding about the effectiveness of this type of intervention an important priority. Aim and design: This systematic review examines the evidence supporting family meetings as a strategy to address the needs of palliative patients and their families. The review conforms to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses Statement. Six medical and psychosocial databases and "CareSearch," a palliative care-specific database, were used to identify studies reporting empirical data, published in English in peer-reviewed journals from 1980 to March 2015. Book chapters, expert opinion, and gray literature were excluded. The Cochrane Collaboration Tool assessed risk of bias. Of the 5051 articles identified, 13 met the inclusion criteria: 10 quantitative and 3 qualitative studies. There was low-level evidence to support family meetings. Only two quantitative pre- and post-studies used a validated palliative care family outcome measure with both studies reporting significant results post-family meetings. Four other quantitative studies reported significant results using non-validated measures. Despite the existence of consensus-based family meeting guidelines, there is a paucity of evidence to support family meetings in the inpatient palliative care setting. Further research using more robust designs, validated outcome measures, and an economic analysis are required to build the family meeting evidence before they are routinely adopted into clinical practice.

Beyond formalism

NASA Technical Reports Server (NTRS)

Denning, Peter J.

1991-01-01

The ongoing debate over the role of formalism and formal specifications in software features many speakers with diverse positions. Yet, in the end, they share the conviction that the requirements of a software system can be unambiguously specified, that acceptable software is a product demonstrably meeting the specifications, and that the design process can be carried out with little interaction between designers and users once the specification has been agreed to. This conviction is part of a larger paradigm prevalent in American management thinking, which holds that organizations are systems that can be precisely specified and optimized. This paradigm, which traces historically to the works of Frederick Taylor in the early 1900s, is no longer sufficient for organizations and software systems today. In the domain of software, a new paradigm, called user-centered design, overcomes the limitations of pure formalism. Pioneered in Scandinavia, user-centered design is spreading through Europe and is beginning to make its way into the U.S.

Effective Personnel Management. The 1980 Regional Meeting NACS Traveling Troupe Presentation.

ERIC Educational Resources Information Center

Arnett, Wayne; Williams, James L.

1981-01-01

Specific suggestions are given for more effective personnel management: careful screening of applicants by one person, a well-designed application form (a sample is provided), good interview techniques, job descriptions, promotions from within, employee manuals, employee orientation, and continuing interpersonal communication. (MSE)

USRD type F63 transducer

NASA Astrophysics Data System (ADS)

Jevnager, M. D.; Tims, A. C.

1981-11-01

A small reversible audio frequency range transducer was developed. The type F63 transducer is designed to meet the specific needs of the user. It is sensitive and stable with temperature and moderate hydrostatic pressures as required by Naval Mine Engineering Facility to improve their mission capability.

School Reform Meets Administrative Realities.

ERIC Educational Resources Information Center

Brown, Antoinette B.; And Others

Maryland's Challenge Grant Program was designed to bring systemic change to schools with relatively low performance levels. This paper presents findings of an ethnographic study that examined the workings of an educational reform effort across several levels of administration. Specifically, the study explored conditions that facilitated and…

Analysis and design of lattice materials for large cord and curvature variations in skin panels of morphing wings

NASA Astrophysics Data System (ADS)

Vigliotti, Andrea; Pasini, Damiano

2015-03-01

In the past few decades, several concepts for morphing wings have been proposed with the aim of improving the structural and aerodynamic performance of conventional aircraft wings. One of the most interesting challenges in the design of a morphing wing is represented by the skin, which needs to meet specific deformation requirements. In particular when morphing involves changes of cord or curvature, the skin is required to undergo large recoverable deformation in the actuation direction, while maintaining the desired shape and strength in the others. One promising material concept that can meet these specifications is represented by lattice materials. This paper examines the use of alternative planar lattices in the embodiment of a skin panel for cord and camber morphing of an aircraft wing. We use a structural homogenization scheme capable of capturing large geometric nonlinearity, to examine the structural performance of lattice skin concepts, as well as to tune their mechanical properties in desired directions.

A Report On Eight Early-Stage State And Regional Projects Testing Value-Based Payment

PubMed Central

Conrad, Douglas; Grembowski, David; Gibbons, Claire; Marcus-Smith, Miriam; Hernandez, Susan E.; Chang, Judy; Renz, Anne; Lau, Bernard; Cruz, Erin dela

2014-01-01

To help contain health care spending and improve the quality of care, practitioners and policy makers are trying to move away from fee-for-service toward value-based payment, which links providers’ reimbursement to the value, rather than the volume, of services delivered. With funding from the Robert Wood Johnson Foundation, eight grantees across the country are designing and implementing value-based payment reform projects. For example, in Salem, Oregon, the Physicians Choice Foundation is testing “Program Oriented Payments,” which include incentives for providers who follow a condition-specific program of care designed to meet goals set jointly by patient and provider. In this article we describe the funding rationale and the specific objectives, strategies, progress, and early stages of implementation of the eight projects. We also share some early lessons and identify prerequisites for success, such as ensuring that providers have broad and timely access to data so they can meet patients’ needs in cost-effective ways. PMID:23650332

DOE Office of Scientific and Technical Information (OSTI.GOV)

Easton, C. R.

The objectives of this program are to establish a heliostat design with the associated manufacturing, assembly, installation and maintenance approaches that will: (1) yield a significant reduction of capital and operating costs; (2) meet performance specifications for large collector subsystems; and (3) can be produced and deployed throughout the southwestern United States. In addition, cost plans and schedules to develop, fabricate, and operate the heliostat are to be developed. This volume presents the collector design, including trade study and test results, and the manufacturing, installation and checkout, and operations and maintenance concepts. Also, a discussion of specification verification and optimizationmore » is included. (WHK)« less

Near-term hybrid vehicle program, phase 1

NASA Technical Reports Server (NTRS)

1979-01-01

The preliminary design of a hybrid vehicle which fully meets or exceeds the requirements set forth in the Near Term Hybrid Vehicle Program is documented. Topics addressed include the general layout and styling, the power train specifications with discussion of each major component, vehicle weight and weight breakdown, vehicle performance, measures of energy consumption, and initial cost and ownership cost. Alternative design options considered and their relationship to the design adopted, computer simulation used, and maintenance and reliability considerations are also discussed.

Treatment of Vestibular Dysfunction Using a Portable Stimulation

DTIC Science & Technology

2016-04-01

2 performed at National University of Ireland Galway i. Fabrication of 20 units based on final design specifications at the National University of...Ireland Galway j. Testing of initial fabricated units from the National University of Ireland Galway in New Jersey to ensure they are meeting required...standards and creating desired improvement k. Shipment of remaining units from National University of Ireland Galway to New Jersey for use in Specific

Treatment of Vestibular Dysfunction Using a Portable Simulator

DTIC Science & Technology

2015-04-01

generation stimulators for fabrication of units for use in Specific Aim 2 performed at National University of Ireland Galway i. Fabrication of 20 units...based on final design specifications at the National University of Ireland Galway j. Testing of initial fabricated units from the National University...of Ireland Galway in New Jersey to ensure they are meeting required standards and creating desired improvement k. Shipment of remaining units from

Picture Archiving And Communication Systems (PACS): Introductory Systems Analysis Considerations

NASA Astrophysics Data System (ADS)

Hughes, Simon H. C.

1983-05-01

Two fundamental problems face any hospital or radiology department that is thinking about installing a Picture Archiving and Communications System (PACS). First, though the need for PACS already exists, much of the relevant technology is just beginning to be developed. Second, the requirements of each hospital are different, so that any attempts to market a single PACS design for use in large numbers of hospitals are likely to meet with the same problems as were experienced with general-purpose Hospital Information Systems. This paper outlines some of the decision processes involved in arriving at specifications for each module of a PACS and indicates design principles which should be followed in order to meet individual hospital requirements, while avoiding the danger of short-term systems obsolescence.

Validation of the F-18 high alpha research vehicle flight control and avionics systems modifications

NASA Technical Reports Server (NTRS)

Chacon, Vince; Pahle, Joseph W.; Regenie, Victoria A.

1990-01-01

The verification and validation process is a critical portion of the development of a flight system. Verification, the steps taken to assure the system meets the design specification, has become a reasonably understood and straightforward process. Validation is the method used to ensure that the system design meets the needs of the project. As systems become more integrated and more critical in their functions, the validation process becomes more complex and important. The tests, tools, and techniques which are being used for the validation of the high alpha research vehicle (HARV) turning valve control system (TVCS) are discussed, and their solutions are documented. The emphasis of this paper is on the validation of integrated systems.

Validation of the F-18 high alpha research vehicle flight control and avionics systems modifications

NASA Technical Reports Server (NTRS)

Chacon, Vince; Pahle, Joseph W.; Regenie, Victoria A.

1990-01-01

The verification and validation process is a critical portion of the development of a flight system. Verification, the steps taken to assure the system meets the design specification, has become a reasonably understood and straightforward process. Validation is the method used to ensure that the system design meets the needs of the project. As systems become more integrated and more critical in their functions, the validation process becomes more complex and important. The tests, tools, and techniques which are being used for the validation of the high alpha research vehicle (HARV) turning vane control system (TVCS) are discussed and the problems and their solutions are documented. The emphasis of this paper is on the validation of integrated system.

Hubble Space telescope thermal cycle test report for large solar array samples with BSFR cells (Sample numbers 703 and 704)

NASA Technical Reports Server (NTRS)

Alexander, D. W.

1992-01-01

The Hubble space telescope (HST) solar array was designed to meet specific output power requirements after 2 years in low-Earth orbit, and to remain operational for 5 years. The array, therefore, had to withstand 30,000 thermal cycles between approximately +100 and -100 C. The ability of the array to meet this requirement was evaluated by thermal cycle testing, in vacuum, two 128-cell solar cell modules that exactly duplicated the flight HST solar array design. Also, the ability of the flight array to survive an emergency deployment during the dark (cold) portion of an orbit was evaluated by performing a cold-roll test using one module.

A Study of the Impacts of Navigational Links, Task Complexity, and Experience with the Older User on Website Usability in a Community College Domain

ERIC Educational Resources Information Center

Garrett, Robin Eileen

2014-01-01

Community colleges serve a diverse population of learners including many older students counting on the community college for enhanced skills or personal enrichment. Many of these colleges target this population with programs designed specifically to meet the needs and goals of the older adult but may not consider this population when designing a…

Job Skills Education Program. Design Specifications

DTIC Science & Technology

1985-03-01

training approach is supplied in part by research based on the depth-of- processing paradigm ( Craik & Lockhart , 1972; Craik & Tulving, 1975), which...discussion here develops a rationale for the approach, which is consistent with research on incidental learning ( Craik & Lockhart , 1972; Craik & Tulving, 1975...this meeting, a plan evolved to integrate available RCA results and contract products into the - JSEP design. 0 During the Task 1 in- process review, the

An FPGA Testbed for Characterizing and Mapping DOD Applications

DTIC Science & Technology

2017-12-27

series expansion helps to linearize pitch control design for wind turbine using linear quadratic regulator (LQR) [15]. In multi-static radar system...A. Mahmud, M. A. Chowdhury, and J. Zhang, “Stability enhancement of dfig wind turbine using lqr pitch control over rated wind speed,” in 2016 IEEE...the problem of meeting payload design specifications is exacerbated by the need to identify manufacturers with interfaces that match the sensors

Design of primers and probes for quantitative real-time PCR methods.

PubMed

Rodríguez, Alicia; Rodríguez, Mar; Córdoba, Juan J; Andrade, María J

2015-01-01

Design of primers and probes is one of the most crucial factors affecting the success and quality of quantitative real-time PCR (qPCR) analyses, since an accurate and reliable quantification depends on using efficient primers and probes. Design of primers and probes should meet several criteria to find potential primers and probes for specific qPCR assays. The formation of primer-dimers and other non-specific products should be avoided or reduced. This factor is especially important when designing primers for SYBR(®) Green protocols but also in designing probes to ensure specificity of the developed qPCR protocol. To design primers and probes for qPCR, multiple software programs and websites are available being numerous of them free. These tools often consider the default requirements for primers and probes, although new research advances in primer and probe design should be progressively added to different algorithm programs. After a proper design, a precise validation of the primers and probes is necessary. Specific consideration should be taken into account when designing primers and probes for multiplex qPCR and reverse transcription qPCR (RT-qPCR). This chapter provides guidelines for the design of suitable primers and probes and their subsequent validation through the development of singlex qPCR, multiplex qPCR, and RT-qPCR protocols.

40 CFR 63.4490 - What emission limits must I meet?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Standards for Hazardous Air Pollutants for Surface Coating of Plastic Parts and Products Emission... used from parameters other than coating consumption and mass solids content (e.g., design specifications for the parts or products coated and the number of items produced). The determination of...

40 CFR 63.4490 - What emission limits must I meet?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Standards for Hazardous Air Pollutants for Surface Coating of Plastic Parts and Products Emission... used from parameters other than coating consumption and mass solids content (e.g., design specifications for the parts or products coated and the number of items produced). The determination of...

Meeting the Pepsi Challenge: Preparing Evaluation Programs for Scholastic Improvement.

ERIC Educational Resources Information Center

Hopkins, Mona S.

This document provides guidelines for preparing evaluation programs for scholastic improvement. The philosophy underlying assessment and accountability is discussed, with specific reference to the positive and negative aspects of assessment. The design of a curriculum evaluation model is presented, including goal identification, data gathering,…

Adapting Curriculum for Augumentative Communication.

ERIC Educational Resources Information Center

Moos, Karen L.; Hartwig, Shirley K.

This paper describes a program for adapting literature for augmentative and alternative communication (AAC) users and students with other disabilities. The program is designed to teach specific language skills that will meet the students' Individualized Education Program goals and to be implemented on a daily basis by classroom instructors. The…

47 CFR 73.53 - Requirements for authorization of antenna monitors.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 4 2014-10-01 2014-10-01 false Requirements for authorization of antenna... antenna monitors. (a) Antenna monitors shall be verified for compliance with the technical requirements in...) An antenna monitor shall meet the following specifications: (1) The monitor shall be designed to...

47 CFR 73.53 - Requirements for authorization of antenna monitors.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 4 2011-10-01 2011-10-01 false Requirements for authorization of antenna... antenna monitors. (a) Antenna monitors shall be verified for compliance with the technical requirements in...) An antenna monitor shall meet the following specifications: (1) The monitor shall be designed to...

47 CFR 73.53 - Requirements for authorization of antenna monitors.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 4 2012-10-01 2012-10-01 false Requirements for authorization of antenna... antenna monitors. (a) Antenna monitors shall be verified for compliance with the technical requirements in...) An antenna monitor shall meet the following specifications: (1) The monitor shall be designed to...

47 CFR 73.53 - Requirements for authorization of antenna monitors.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Requirements for authorization of antenna... antenna monitors. (a) Antenna monitors shall be verified for compliance with the technical requirements in...) An antenna monitor shall meet the following specifications: (1) The monitor shall be designed to...

47 CFR 73.53 - Requirements for authorization of antenna monitors.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 4 2013-10-01 2013-10-01 false Requirements for authorization of antenna... antenna monitors. (a) Antenna monitors shall be verified for compliance with the technical requirements in...) An antenna monitor shall meet the following specifications: (1) The monitor shall be designed to...

Developmental Education: The Recognition of Individual Differences

ERIC Educational Resources Information Center

Blimline, Carol; Klimek, Richard

1977-01-01

This article describes the historical, empirical, and theoretical aspects of a series of one-credit student development courses offered at a multicampus community college. The courses, ranging from "The Emerging Woman" to "Study Skills," were specifically designed to meet a variety of developmental needs for a diverse student…

Key Actor Perceptions of Athletics Strategy

ERIC Educational Resources Information Center

Collins, William Thomas

2012-01-01

Athletics strategy refers to specific initiatives within the intercollegiate athletics program that are designed to meet the broader strategic goals of a post-secondary institution. This case focused on athletics strategy decisions that were enacted within the context of organizational change as Cartwright College, a pseudonym, transitioned from a…

Retail Training and Education.

ERIC Educational Resources Information Center

Bloodworth, Margaret

The book provides insight into training aims, principles, techniques, aids , and courses designed to meet the training needs of specific groups of staff, such as management staff, training staff, new staff, and established staff. It also covers the training and educational elements of the Certificate of Retail Management Principles. Training…

The Bartlesville System; TGISS Software Documentation.

ERIC Educational Resources Information Center

Roberts, Tommy L.; And Others

TGISS (Total Guidance Information Support System) is an information storage and retrieval system specifically designed to meet the needs and requirements of a counselor in the Bartlesville Public School environment. The system, which is a combination of man/machine capabilities, includes the hardware and software necessary to extend the…

The design and development of a rectangular, shingle-type photovoltaic module

NASA Astrophysics Data System (ADS)

Shepard, N. F., Jr.

A shingle-type photovoltaic module has been designed and developed to meet the requirements of specifications for residential applications. The module is ideally suited for installation directly to the sheathing of a sloping, south-facing roof of a residential, industrial, or commercial building. The design requirements are examined, taking into account also module safety requirements. Aspects of module design and analysis are discussed, giving attention to installation details, solar cells and electrical circuit design, the encapsulation system, substrate lamination, and the module-to-module interconnecting cable. Details of module assembly experience and test and outdoor exposure experience are also considered.

The design and development of a rectangular, shingle-type photovoltaic module

NASA Technical Reports Server (NTRS)

Shepard, N. F., Jr.

1982-01-01

A shingle-type photovoltaic module has been designed and developed to meet the requirements of specifications for residential applications. The module is ideally suited for installation directly to the sheathing of a sloping, south-facing roof of a residential, industrial, or commercial building. The design requirements are examined, taking into account also module safety requirements. Aspects of module design and analysis are discussed, giving attention to installation details, solar cells and electrical circuit design, the encapsulation system, substrate lamination, and the module-to-module interconnecting cable. Details of module assembly experience and test and outdoor exposure experience are also considered.

A Simulation Modeling Approach Method Focused on the Refrigerated Warehouses Using Design of Experiment

NASA Astrophysics Data System (ADS)

Cho, G. S.

2017-09-01

For performance optimization of Refrigerated Warehouses, design parameters are selected based on the physical parameters such as number of equipment and aisles, speeds of forklift for ease of modification. This paper provides a comprehensive framework approach for the system design of Refrigerated Warehouses. We propose a modeling approach which aims at the simulation optimization so as to meet required design specifications using the Design of Experiment (DOE) and analyze a simulation model using integrated aspect-oriented modeling approach (i-AOMA). As a result, this suggested method can evaluate the performance of a variety of Refrigerated Warehouses operations.

Development of a parameter optimization technique for the design of automatic control systems

NASA Technical Reports Server (NTRS)

Whitaker, P. H.

1977-01-01

Parameter optimization techniques for the design of linear automatic control systems that are applicable to both continuous and digital systems are described. The model performance index is used as the optimization criterion because of the physical insight that can be attached to it. The design emphasis is to start with the simplest system configuration that experience indicates would be practical. Design parameters are specified, and a digital computer program is used to select that set of parameter values which minimizes the performance index. The resulting design is examined, and complexity, through the use of more complex information processing or more feedback paths, is added only if performance fails to meet operational specifications. System performance specifications are assumed to be such that the desired step function time response of the system can be inferred.

Manufacturability: from design to SPC limits through "corner-lot" characterization

NASA Astrophysics Data System (ADS)

Hogan, Timothy J.; Baker, James C.; Wesneski, Lisa; Black, Robert S.; Rothenbury, Dave

2004-12-01

Texas Instruments" Digital Micro-mirror Device, is used in a wide variety of optical display applications ranging from fixed and portable projectors to high-definition television (HDTV) to digital cinema projection systems. A new DMD pixel architecture, called "FTP", was designed and qualified by Texas Instruments DLPTMTM Group in 2003 to meet increased performance objectives for brightness and contrast ratio. Coordination between design, test and fabrication groups was required to balance pixel performance requirements and manufacturing capability. "Corner Lot" designed experiments (DOE) were used to verify "fabrication space" available for the pixel design. The corner lot technique allows confirmation of manufacturability projections early in the design/qualification cycle. Through careful design and analysis of the corner-lot DOE, a balance of critical dimension (cd) "budgets" is possible so that specification and process control limits can be established that meet both customer and factory requirements. The application of corner-lot DOE is illustrated in a case history of the DMD "FTP" pixel. The process for balancing test parameter requirements with multiple critical dimension budgets is shown. MEMS/MOEMS device design and fabrication can use similar techniques to achieve agressive design-to-qualification goals.

Manufacturability: from design to SPC limits through "corner-lot" characterization

NASA Astrophysics Data System (ADS)

Hogan, Timothy J.; Baker, James C.; Wesneski, Lisa; Black, Robert S.; Rothenbury, Dave

2005-01-01

Texas Instruments" Digital Micro-mirror Device, is used in a wide variety of optical display applications ranging from fixed and portable projectors to high-definition television (HDTV) to digital cinema projection systems. A new DMD pixel architecture, called "FTP", was designed and qualified by Texas Instruments DLPTMTM Group in 2003 to meet increased performance objectives for brightness and contrast ratio. Coordination between design, test and fabrication groups was required to balance pixel performance requirements and manufacturing capability. "Corner Lot" designed experiments (DOE) were used to verify "fabrication space" available for the pixel design. The corner lot technique allows confirmation of manufacturability projections early in the design/qualification cycle. Through careful design and analysis of the corner-lot DOE, a balance of critical dimension (cd) "budgets" is possible so that specification and process control limits can be established that meet both customer and factory requirements. The application of corner-lot DOE is illustrated in a case history of the DMD "FTP" pixel. The process for balancing test parameter requirements with multiple critical dimension budgets is shown. MEMS/MOEMS device design and fabrication can use similar techniques to achieve agressive design-to-qualification goals.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kornfeldt, H.; Bjoerk, K.O.; Ekstroem, P.

The protection against dynamic effects in connection with potential pipe breaks has been implemented in different ways in the development of BWR reactor designs. First-generation plant designs reflect code requirements in effect at that time which means that no piping restraint systems were designed and built into those plants. Modern designs have, in contrast, implemented full protection against damage in connection with postulated pipe breaks, as required in current codes and regulations. Moderns standards and current regulatory demands can be met for the older plants by backfitting pipe whip restraint hardware. This could lead to several practical difficulties as thesemore » installations were not anticipated in the original plant design and layout. Meeting the new demands by analysis would in this situation have great advantages. Application of leak-before-break criteria gives an alternative opportunity of meeting modem standards in reactor safety design. Analysis takes into account data specific to BWR primary system operation, actual pipe material properties, piping loads and leak detection capability. Special attention must be given to ensure that the data used reflects actual plant conditions.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Albis, A.H.A.

This research effort is concerned with the identification and utilization of practical design guidelines to meet the demand for guidance in innovative planning and building design for Egyptian desert conditions. An energy-conscious design can be realized with a minimum expenditure of exhaustible energy resources and maximum utilization of the natural energies for cooling and heating. The energy design guidelines developed will be applied to an Urban Center, on a site selected to alleviate the stress on Cairo, which has been suffering for over two decades from housing shortages due to overpopulation. Design criteria to meet the challenges of this researchmore » include: neighborhood planning; orientation; building details; shading; colors of walls and roofs; materials; and massing configuration. In this research, desert construction and its aspects, use of building materials, approaches to energy conservation, and architectural principles for neighborhood planning are identified. The human requirement for thermal comfort specific to desert environments are analyzed and related to diurnal and annual patterns of outdoor conditions, and to the potential for modifying indoor thermal conditions by designs suitable to prevailing climatic conditions.« less

Thermal Management and Reliability of Automotive Power Electronics and Electric Machines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Narumanchi, Sreekant V; Bennion, Kevin S; Cousineau, Justine E

Low-cost, high-performance thermal management technologies are helping meet aggressive power density, specific power, cost, and reliability targets for power electronics and electric machines. The National Renewable Energy Laboratory is working closely with numerous industry and research partners to help influence development of components that meet aggressive performance and cost targets through development and characterization of cooling technologies, and thermal characterization and improvements of passive stack materials and interfaces. Thermomechanical reliability and lifetime estimation models are important enablers for industry in cost-and time-effective design.

Space Nuclear Thermal Propulsion (SNTP) Air Force facility

NASA Technical Reports Server (NTRS)

Beck, David F.

1993-01-01

The Space Nuclear Thermal Propulsion (SNTP) Program is an initiative within the US Air Force to acquire and validate advanced technologies that could be used to sustain superior capabilities in the area or space nuclear propulsion. The SNTP Program has a specific objective of demonstrating the feasibility of the particle bed reactor (PBR) concept. The term PIPET refers to a project within the SNTP Program responsible for the design, development, construction, and operation of a test reactor facility, including all support systems, that is intended to resolve program technology issues and test goals. A nuclear test facility has been designed that meets SNTP Facility requirements. The design approach taken to meet SNTP requirements has resulted in a nuclear test facility that should encompass a wide range of nuclear thermal propulsion (NTP) test requirements that may be generated within other programs. The SNTP PIPET project is actively working with DOE and NASA to assess this possibility.

Non-Toxic Orbital Maneuvering System Engine Development

NASA Technical Reports Server (NTRS)

Green, Christopher; Claflin, Scott; Maeding, Chris; Butas, John

1999-01-01

Recent results using the Aestus engine operated with LOx/ethanol propellant are presented. An experimental program at Rocketdyne Propulsion and Power is underway to adapt this engine for the Boeing Reusable Space Systems Division non-toxic Orbital Maneuvering System/Reaction control System (OMS/RCS) system. Daimler-Chrysler Aerospace designed the Aestus as an nitrogen tetroxide/monomethyl hydrazine (NTO/MMH) upper-stage engine for the Ariane 5. The non-toxic OMS/RCS system's preliminary design requires a LOx/ethanol (O2/C2H5OH) engine that operates with a mixture ratio of 1.8, a specific impulse of 323 seconds, and fits within the original OMS design envelope. This paper describes current efforts to meet these requirements including, investigating engine performance using LOx/ethanol, developing the en-ine system sizing package, and meeting the vehicle operation parameters. Data from hot-fire testing are also presented and discussed.

MHD program plan, FY 1991

NASA Astrophysics Data System (ADS)

1990-10-01

The current magnetohydrodynamic MHD program being implemented is a result of a consensus established in public meetings held by the Department of Energy in 1984. The public meetings were followed by the formulation of a June 1984 Coal-Fired MHD Preliminary Transition and Program Plan. This plan focused on demonstrating the proof-of-concept (POC) of coal-fired MHD electric power plants by the early 1990s. MHD test data indicate that while there are no fundamental technical barriers impeding the development of MHD power plants, technical risk remains. To reduce the technical risk three key subsystems (topping cycle, bottoming cycle, and seed regeneration) are being assembled and tested separately. The program does not require fabrication of a complete superconducting magnet, but rather the development and testing of superconductor cables. The topping cycle system test objectives can be achieved using a conventional iron core magnet system already in place at a DOE facility. Systems engineering-derived requirements and analytical modeling to support scale-up and component design guide the program. In response to environmental, economic, engineering, and utility acceptance requirements, design choices and operating modes are tested and refined to provide technical specifications for meeting commercial criteria. These engineering activities are supported by comprehensive and continuing systems analyses to establish realistic technical requirements and cost data. Essential elements of the current program are to: develop technical and environmental data for the integrated MHD topping cycle and bottoming cycle systems through POC testing (1000 and 4000 hours, respectively); design, construct, and operate a POC seed regeneration system capable of processing spent seed materials from the MHD bottoming cycle; prepare conceptual designs for a site specific MHD retrofit plant; and continue supporting research necessary for system testing.

29 CFR 776.27 - Construction which is related to covered production.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., gravel, asphalt, cement, crushed rock, railroad ties, pipes, conduits, wires, concrete pilings and other... designed”, or meeting particular specifications, for use in production of particular kinds of goods for... contemplated, will not ordinarily be considered covered. However, if the new building is designed as a...

40 CFR 63.4490 - What emission limits must I meet?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) National Emission Standards for Hazardous Air Pollutants for Surface Coating of Plastic Parts and Products... estimate the relative mass of coating solids used from parameters other than coating consumption and mass solids content (e.g., design specifications for the parts or products coated and the number of items...

40 CFR 63.4490 - What emission limits must I meet?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) National Emission Standards for Hazardous Air Pollutants for Surface Coating of Plastic Parts and Products... estimate the relative mass of coating solids used from parameters other than coating consumption and mass solids content (e.g., design specifications for the parts or products coated and the number of items...

40 CFR 63.4490 - What emission limits must I meet?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) National Emission Standards for Hazardous Air Pollutants for Surface Coating of Plastic Parts and Products... estimate the relative mass of coating solids used from parameters other than coating consumption and mass solids content (e.g., design specifications for the parts or products coated and the number of items...

Investigation of Use of Slag Aggregates and Slag Cements in Concrete Pavements to Reduce the Maintenance Cost

DOT National Transportation Integrated Search

2017-12-01

The objective of this research was to evaluate the influence of using the ACBFS aggregate (slag aggregate) as a replacement for natural aggregates on the properties of pavement concrete designed to meet the standard specifications of the Indiana Depa...

Writing Better Software for Economics Principles Textbooks.

ERIC Educational Resources Information Center

Walbert, Mark S.

1989-01-01

Examines computer software currently available with most introductory economics textbooks. Compares what is available with what should be available in order to meet the goal of effectively using the microcomputer to teach economic principles. Recommends 14 specific pedagogical changes that should be made in order to improve current designs. (LS)

77 FR 38769 - 97th Annual Meeting of the National Conference on Weights and Measures

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-29

... testing equipment that comprise the regulatory control of commercial weighing and measuring devices. The... specifications to recognize current marketing practices of offering pre or post delivery discounts on fuel prices... proposal would allow device manufacturers greater flexibility in the design and operation of customer...

Student Satisfaction with an Innovative Internship

ERIC Educational Resources Information Center

Petrila, Ann; Fireman, Orah; Fitzpatrick, Leslie Schnoll; Hodas, Robyn Wertheimer; Taussig, Heather N.

2015-01-01

This article describes an internship program designed specifically to meet graduate students' training needs within the context of their work in a prevention program for children in foster care. An internship based on a strong model of intern recruitment and supervision, structured inclusion of interns in a supportive agency culture, a…

The Department of Humanities Writing Program.

ERIC Educational Resources Information Center

Umpqua Community Coll., Roseburg, OR.

Designed for students, faculty, and others interested in the writing program at Umpqua Community College (UCC) in Oregon, this booklet clarifies the specific function and scope of the writing courses offered by UCC's Department of Humanities. Section I states the department's objectives (e.g., to provide a core curriculum meeting the requirements…

Communicating Effectively in Japanese for Business. Second Year.

ERIC Educational Resources Information Center

Hijirida, Kyoko; Sato, Carrie N.

Designed for university students majoring in business with specific occupational goals involving the tourist industry, this textbook was developed to meet both academic and society needs by providing a clear relationship between the Japanese language class and the student's major field of study. The textbook focuses on three objectives: to produce…

Service Learning: Opportunities for Legal Studies in Business

ERIC Educational Resources Information Center

Burke, Debra D.

2007-01-01

Service learning is a form of experiential learning designed to engage students, faculty, and community partners in a mutually beneficial experience. Specifically, it "is a credit-bearing, educational experience in which students participate in an organized service activity that meets identified community needs and reflects on the service activity…

Effectiveness of Existing Eye Safety Legislation in Arizona.

ERIC Educational Resources Information Center

Gillaspy, Roy Eugene

This study was designed to ascertain the current practices of eye safety in Arizona high school industrial education laboratories, including the enforcement of eye safety legislation, use of eye protection devices, how the eye ware meets the American National Standards Institute specifications, and the teachers' interpretations of the existing eye…

Industrial Technology Orientation Curriculum Guide.

ERIC Educational Resources Information Center

Illinois State Board of Education, Springfield. Dept. of Adult, Vocational and Technical Education.

The four courses in this guide were designed to meet the specifications for the career orientation level of Illinois' Education for Employment Curriculum Model. These orientation-level courses can be taken by high school students in any sequence: (1) communication technology; (2) energy utilization technology; (3) production technology; and (4)…

"Doing" Social Studies: A Framework for the Historical and Cultural Analysis of Electricity.

ERIC Educational Resources Information Center

Gambro, John S.; Ingold, Barbara S.

1997-01-01

Briefly describes activities and questions designed to integrate the study of electricity into any of the specific social studies disciplines. Meeting the performance expectations of the National Standards, the activities are connected to archaeology, anthropology, geography, history, economics, political science, law, religion, philosophy,…

7 CFR 29.1132 - Rule 26.

Code of Federal Regulations, 2010 CFR

2010-01-01

... INSPECTION Standards Rules § 29.1132 Rule 26. Tobacco that contains a moderate amount of dirt or sand, but which otherwise meets the specifications of any Primings grade, including the first quality Nondescript from the Primings group, shall be designated by placing the special factor, “dirt” or “sand” after the...

Design and fabrication of solar cell modules

NASA Technical Reports Server (NTRS)

Shaughnessy, T. P.

1978-01-01

A program conducted for design, fabrication and evaluation of twelve silicon solar cell modules is described. The purpose of the program was to develop a module design consistent with the requirements and objectives of JPL specification and to also incorporate elements of new technologies under development to meet LSSA Project goals. Module development emphasized preparation of a technically and economically competitive design based upon utilization of ion implanted solar cells and a glass encapsulation system. The modules fabricated, tested and delivered were of nominal 2 X 2 foot dimensions and 20 watt minimum rating. Basic design, design rationale, performance and results of environmental testing are described.

CEM-designer: design of custom expression microarrays in the post-ENCODE Era.

PubMed

Arnold, Christian; Externbrink, Fabian; Hackermüller, Jörg; Reiche, Kristin

2014-11-10

Microarrays are widely used in gene expression studies, and custom expression microarrays are popular to monitor expression changes of a customer-defined set of genes. However, the complexity of transcriptomes uncovered recently make custom expression microarray design a non-trivial task. Pervasive transcription and alternative processing of transcripts generate a wealth of interweaved transcripts that requires well-considered probe design strategies and is largely neglected in existing approaches. We developed the web server CEM-Designer that facilitates microarray platform independent design of custom expression microarrays for complex transcriptomes. CEM-Designer covers (i) the collection and generation of a set of unique target sequences from different sources and (ii) the selection of a set of sensitive and specific probes that optimally represents the target sequences. Probe design itself is left to third party software to ensure that probes meet provider-specific constraints. CEM-Designer is available at http://designpipeline.bioinf.uni-leipzig.de. Copyright © 2014 Elsevier B.V. All rights reserved.

Skylab vectorcardiograph: System description and in flight operation

NASA Technical Reports Server (NTRS)

Lintott, J.; Costello, M. J.

1975-01-01

A vectorcardiograph system was used to measure cardiac electrical activity of Skylab crewmen. This system was chosen because of its data-quantification advantages. The vectorcardiograph was required to meet recommended American Heart Association specifications, to withstand space environmental extremes, and to facilitate data gathering in the weightless environment. The vectorcardiograph system performed without failure, and all projected data were acquired. The appendix lists the design specifications used for the Skylab vectorcardiograph system.

Veterans’ Health Care: Limited Progress Made to Address Concerns That Led to High Risk Designation

DTIC Science & Technology

2017-03-15

partially meet two of the five criteria GAO uses to assess removal from the High-Risk List ( leadership commitment and an action plan), but it has not met...the other three (agency capacity, monitoring efforts, and demonstrated progress). Specifically, VA officials have taken leadership actions such as...high-risk designation, additional actions are required of VA, including: (1) demonstrating stronger leadership support as it continues its

DESIGN AND CONSTRUCTION OF SCHOOL BUILDINGS. PROCEEDINGS, ASSOCIATION OF SCHOOL BUSINESS OFFICIALS OF THE UNITED STATES AND CANADA, ANNUAL MEETING AND EDUCATIONAL EXHIBIT, (50TH SAN FRANCISCO, CALIFORNIA, OCTOBER 71-22, 1964).

ERIC Educational Resources Information Center

LIEBESKIND, MORRIS

PROBLEMS IN THE SCHEDULING AND COMPLETION OF SCHOOL BUILDING DESIGN AND CONSTRUCTION PROJECTS ARE DISCUSSED WITH REFERENCE TO THE CRITICAL PATH METHOD OF PROGRAMING. THE DISCUSSION GIVES A BROAD OVERVIEW OF THE METHOD WITH DETAILED SUGGESTIONS FOR SCHOOL ADMINISTRATORS. SPECIFIC SUBJECT AREAS INCLUDE--(1) CPM, A NEW MANAGEMENT TOOL, (2) CPM…

Performance of species occurrence estimators when basic assumptions are not met: a test using field data where true occupancy status is known

USGS Publications Warehouse

Miller, David A. W.; Bailey, Larissa L.; Grant, Evan H. Campbell; McClintock, Brett T.; Weir, Linda A.; Simons, Theodore R.

2015-01-01

Our results demonstrate that even small probabilities of misidentification and among-site detection heterogeneity can have severe effects on estimator reliability if ignored. We challenge researchers to place greater attention on both heterogeneity and false positives when designing and analysing occupancy studies. We provide 9 specific recommendations for the design, implementation and analysis of occupancy studies to better meet this challenge.

Inertial Navigation System for India's Reusable Launch Vehicle-Technology Demonstrator (RLV-TD HEX) Mission

NASA Astrophysics Data System (ADS)

Umadevi, P.; Navas, A.; Karuturi, Kesavabrahmaji; Shukkoor, A. Abdul; Kumar, J. Krishna; Sreekumar, Sreejith; Basim, A. Mohammed

2017-12-01

This work presents the configuration of Inertial Navigation System (INS) used in India's Reusable Launch Vehicle-Technology Demonstrator (RLV-TD) Program. In view of the specific features and requirements of the RLV-TD, specific improvements and modifications were required in the INS. A new system was designed, realised and qualified meeting the mission requirements of RLV-TD, at the same time taking advantage of the flight heritage attained in INS through various Launch vehicle Missions of the country. The new system has additional redundancy in acceleration channel, in-built inclinometer based bias update scheme for acceleration channels and sign conventions as employed in an aircraft. Data acquisition in micro cycle periodicity (10 ms) was incorporated which was required to provide rate and attitude information at higher sampling rate for ascent phase control. Provision was incorporated for acquisition of rate and acceleration data with high resolution for aerodynamic characterisation and parameter estimation. GPS aided navigation scheme was incorporated to meet the stringent accuracy requirements of the mission. Navigation system configuration for RLV-TD, specific features incorporated to meet the mission requirements, various tests carried out and performance during RLV-TD flight are highlighted.

Standard High Solids Vessel Design De-inventory Simulant Qualification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fiskum, Sandra K.; Burns, Carolyn A.M.; Gauglitz, Phillip A.

The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is working to develop a Standard High Solids Vessel Design (SHSVD) process vessel. To support testing of this new design, WTP engineering staff requested that a Newtonian simulant be developed that would represent the de-inventory (residual high-density tank solids cleanout) process. Its basis and target characteristics are defined in 24590-WTP-ES-ENG-16-021 and implemented through PNNL Test Plan TP-WTPSP-132 Rev. 1.0. This document describes the de-inventory Newtonian carrier fluid (DNCF) simulant composition that will satisfy the basis requirement to mimic the density (1.18 g/mL ± 0.1 g/mL) and viscosity (2.8 cP ± 0.5more » cP) of 5 M NaOH at 25 °C.1 The simulant viscosity changes significantly with temperature. Therefore, various solution compositions may be required, dependent on the test stand process temperature range, to meet these requirements. Table ES.1 provides DNCF compositions at selected temperatures that will meet the density and viscosity specifications as well as the temperature range at which the solution will meet the acceptable viscosity tolerance.« less

Electrical resistivity well-logging system with solid-state electronic circuitry

USGS Publications Warehouse

Scott, James Henry; Farstad, Arnold J.

1977-01-01

An improved 4-channel electrical resistivity well-logging system for use with a passive probe with electrodes arranged in the 'normal' configuration has been designed and fabricated by Westinghouse Electric Corporation to meet technical specifications developed by the U.S. Geological Survey. Salient features of the system include solid-state switching and current regulation in the transmitter circuit to produce a constant-current source square wave, and synchronous solid-state switching and sampling of the potential waveform in the receiver circuit to provide an analog dc voltage proportions to the measured resistivity. Technical specifications and design details are included in this report.

Shuttle bit rate synchronizer. [signal to noise ratios and error analysis

NASA Technical Reports Server (NTRS)

Huey, D. C.; Fultz, G. L.

1974-01-01

A shuttle bit rate synchronizer brassboard unit was designed, fabricated, and tested, which meets or exceeds the contractual specifications. The bit rate synchronizer operates at signal-to-noise ratios (in a bit rate bandwidth) down to -5 dB while exhibiting less than 0.6 dB bit error rate degradation. The mean acquisition time was measured to be less than 2 seconds. The synchronizer is designed around a digital data transition tracking loop whose phase and data detectors are integrate-and-dump filters matched to the Manchester encoded bits specified. It meets the reliability (no adjustments or tweaking) and versatility (multiple bit rates) of the shuttle S-band communication system through an implementation which is all digital after the initial stage of analog AGC and A/D conversion.

Where microbiology meets microengineering: design and applications of reporter bacteria.

PubMed

van der Meer, Jan Roelof; Belkin, Shimshon

2010-07-01

Bacteria have long been the targets for genetic manipulation, but more recently they have been synthetically designed to carry out specific tasks. Among the simplest of these tasks is chemical compound and toxicity detection coupled to the production of a quantifiable reporter signal. In this Review, we describe the current design of bacterial bioreporters and their use in a range of assays to measure the presence of harmful chemicals in water, air, soil, food or biological specimens. New trends for integrating synthetic biology and microengineering into the design of bacterial bioreporter platforms are also highlighted.

Design and analysis of tubular permanent magnet linear generator for small-scale wave energy converter

NASA Astrophysics Data System (ADS)

Kim, Jeong-Man; Koo, Min-Mo; Jeong, Jae-Hoon; Hong, Keyyong; Cho, Il-Hyoung; Choi, Jang-Young

2017-05-01

This paper reports the design and analysis of a tubular permanent magnet linear generator (TPMLG) for a small-scale wave-energy converter. The analytical field computation is performed by applying a magnetic vector potential and a 2-D analytical model to determine design parameters. Based on analytical solutions, parametric analysis is performed to meet the design specifications of a wave-energy converter (WEC). Then, 2-D FEA is employed to validate the analytical method. Finally, the experimental result confirms the predictions of the analytical and finite element analysis (FEA) methods under regular and irregular wave conditions.

Software design by reusing architectures

NASA Technical Reports Server (NTRS)

Bhansali, Sanjay; Nii, H. Penny

1992-01-01

Abstraction fosters reuse by providing a class of artifacts that can be instantiated or customized to produce a set of artifacts meeting different specific requirements. It is proposed that significant leverage can be obtained by abstracting software system designs and the design process. The result of such an abstraction is a generic architecture and a set of knowledge-based, customization tools that can be used to instantiate the generic architecture. An approach for designing software systems based on the above idea are described. The approach is illustrated through an implemented example, and the advantages and limitations of the approach are discussed.

AN ASSESSMENT OF FLYWHEEL HIGH POWER ENERGY STORAGE TECHNOLOGY FOR HYBRID VEHICLES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hansen, James Gerald

2012-02-01

An assessment has been conducted for the DOE Vehicle Technologies Program to determine the state of the art of advanced flywheel high power energy storage systems to meet hybrid vehicle needs for high power energy storage and energy/power management. Flywheel systems can be implemented with either an electrical or a mechanical powertrain. The assessment elaborates upon flywheel rotor design issues of stress, materials and aspect ratio. Twelve organizations that produce flywheel systems submitted specifications for flywheel energy storage systems to meet minimum energy and power requirements for both light-duty and heavy-duty hybrid applications of interest to DOE. The most extensivemore » experience operating flywheel high power energy storage systems in heavy-duty and light-duty hybrid vehicles is in Europe. Recent advances in Europe in a number of vehicle racing venues and also in road car advanced evaluations are discussed. As a frame of reference, nominal weight and specific power for non-energy storage components of Toyota hybrid electric vehicles are summarized. The most effective utilization of flywheels is in providing high power while providing just enough energy storage to accomplish the power assist mission effectively. Flywheels are shown to meet or exceed the USABC power related goals (discharge power, regenerative power, specific power, power density, weight and volume) for HEV and EV batteries and ultracapacitors. The greatest technical challenge facing the developer of vehicular flywheel systems remains the issue of safety and containment. Flywheel safety issues must be addressed during the design and testing phases to ensure that production flywheel systems can be operated with adequately low risk.« less

Quality risk management in pharmaceutical development.

PubMed

Charoo, Naseem Ahmad; Ali, Areeg Anwer

2013-07-01

The objective of ICH Q8, Q9 and Q10 documents is application of systemic and science based approach to formulation development for building quality into product. There is always some uncertainty in new product development. Good risk management practice is essential for success of new product development in decreasing this uncertainty. In quality by design paradigm, the product performance properties relevant to the patient are predefined in target product profile (TPP). Together with prior knowledge and experience, TPP helps in identification of critical quality attributes (CQA's). Initial risk assessment which identifies risks to these CQA's provides impetus for product development. Product and process are designed to gain knowledge about these risks, devise strategies to eliminate or mitigate these risks and meet objectives set in TPP. By laying more emphasis on high risk events the protection level of patient is increased. The process being scientifically driven improves the transparency and reliability of the manufacturer. The focus on risk to the patient together with flexible development approach saves invaluable resources, increases confidence on quality and reduces compliance risk. The knowledge acquired in analysing risks to CQA's permits construction of meaningful design space. Within the boundaries of the design space, variation in critical material characteristics and process parameters must be managed in order to yield a product having the desired characteristics. Specifications based on product and process understanding are established such that product will meet the specifications if tested. In this way, the product is amenable to real time release, since specifications only confirm quality but they do not serve as a means of effective process control.

Design of a diamond-crystal monochromator for the LCLS hard x-ray self-seeding project

NASA Astrophysics Data System (ADS)

Shu, D.; Shvyd'ko, Y.; Amann, J.; Emma, P.; Stoupin, S.; Quintana, J.

2013-03-01

As the result of collaborations between the Advanced Photon Source (APS), Argonne National Laboratory, and the Linac Coherent Light Source (LCLS) at SLAC National Accelerator Laboratory, we have designed and constructed a diamond crystal monochromator for the LCLS hard x-ray self-seeding project. The novel monochromator is ultrahigh-vacuum compatible to meet the LCLS linear accelerator vacuum environmental requirement. A special graphite holder was designed for strain-free mount of the 110-μm thin synthetic diamond crystal plate provided by Technological Institute for Super-hard and Novel Carbon Materials of Russia (TISNCM). An in-vacuum multi-axis precision positioning mechanism is designed to manipulate the thin-film diamond holder with resolutions and stabilities required by the hard x-ray self-seeding physics. Optical encoders, limit switches, and hardware stops are established in the mechanism to ensure system reliability and to meet the accelerator personal and equipment safety interlock requirements. Molybdenum shields are installed in the monochromator to protect the encoders and associated electronics from radiation damage. Mechanical specifications, designs, and preliminary test results of the diamond monochromator are presented in this paper.

Energy Efficient Engine Flight Propulsion System Preliminary Analysis and Design Report

NASA Technical Reports Server (NTRS)

Bisset, J. W.; Howe, D. C.

1983-01-01

The final design and analysis of the flight propulsion system is presented. This system is the conceptual study engine defined to meet the performance, economic and environmental goals established for the Energy Efficient Engine Program. The design effort included a final definition of the engine, major components, internal subsystems, and nacelle. Various analytical representations and results from component technology programs are used to verify aerodynamic and structural design concepts and to predict performance. Specific design goals and specifications, reflecting future commercial aircraft propulsion system requirements for the mid-1980's, are detailed by NASA and used as guidelines during engine definition. Information is also included which details salient results from a separate study to define a turbofan propulsion system, known as the maximum efficiency engine, which reoptimized the advanced fuel saving technologies for improved fuel economy and direct operating costs relative to the flight propulsion system.

Tool for Turbine Engine Closed-Loop Transient Analysis (TTECTrA) Users' Guide

NASA Technical Reports Server (NTRS)

Csank, Jeffrey T.; Zinnecker, Alicia M.

2014-01-01

The tool for turbine engine closed-loop transient analysis (TTECTrA) is a semi-automated control design tool for subsonic aircraft engine simulations. At a specific flight condition, TTECTrA produces a basic controller designed to meet user-defined goals and containing only the fundamental limiters that affect the transient performance of the engine. The purpose of this tool is to provide the user a preliminary estimate of the transient performance of an engine model without the need to design a full nonlinear controller.

Jefferson Lab CLAS12 Superconducting Solenoid magnet Requirements and Design Evolution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rajput-Ghoshal, Renuka; Hogan, John P.; Fair, Ruben J.

2014-12-01

As part of the Jefferson Lab 12GeV accelerator upgrade project, one of the experimental halls (Hall B) requires two superconducting magnets. One is a magnet system consisting of six superconducting trapezoidal racetrack-type coils assembled in a toroidal configuration and the second is an actively shielded solenoidal magnet system consisting of 5 coils. In this presentation the physics requirements for the 5 T solenoid magnet, design constraints, conductor decision, and cooling choice will be discussed. The various design iterations to meet the specification will also be discussed in this presentation.

DSN radio science system design and testing for Voyager-Neptune encounter

NASA Technical Reports Server (NTRS)

Ham, N. C.; Rebold, T. A.; Weese, J. F.

1989-01-01

The Deep Space Network (DSN) Radio Science System presently implemented within the Deep Space Network was designed to meet stringent requirements imposed by the demands of the Voyager-Neptune encounter and future missions. One of the initial parameters related to frequency stability is discussed. The requirement, specification, design, and methodology for measuring this parameter are described. A description of special instrumentation that was developed for the test measurements and initial test data resulting from the system tests performed at Canberra, Australia and Usuda, Japan are given.

Specimen Designs for Testing Advanced Aeropropulsion Materials Under In-Plane Biaxial Loading

NASA Technical Reports Server (NTRS)

Ellis, John R.; Abul-Aziz, Ali

2003-01-01

A design study was undertaken to develop specimen designs for testing advanced aeropropulsion materials under in-plane biaxial loading. The focus of initial work was on developing a specimen design suitable for deformation and strength tests to be conducted under monotonic loading. The type of loading initially assumed in this study was the special case of equibiaxial, tensile loading. A specimen design was successfully developed after a lengthy design and optimization process with overall dimensions of 12 by 12 by 0.625 in., and a gage area of 3.875 by 3.875 by 0.080 in. Subsequently, the scope of the work was extended to include the development of a second design tailored for tests involving cyclic loading. A specimen design suitably tailored to meet these requirements was successfully developed with overall dimensions of 12 by 12 by 0.500 in. and a gage area of 2.375 by 2.375 by 0.050 in. Finally, an investigation was made to determine whether the specimen designs developed in this study for equibiaxial, tensile loading could be used without modification to investigate general forms of biaxial loading. For best results, it was concluded that specimen designs need to be optimized and tailored to meet the specific loading requirements of individual research programs.

Efficient design of nanoplasmonic waveguide devices using the space mapping algorithm.

PubMed

Dastmalchi, Pouya; Veronis, Georgios

2013-12-30

We show that the space mapping algorithm, originally developed for microwave circuit optimization, can enable the efficient design of nanoplasmonic waveguide devices which satisfy a set of desired specifications. Space mapping utilizes a physics-based coarse model to approximate a fine model accurately describing a device. Here the fine model is a full-wave finite-difference frequency-domain (FDFD) simulation of the device, while the coarse model is based on transmission line theory. We demonstrate that simply optimizing the transmission line model of the device is not enough to obtain a device which satisfies all the required design specifications. On the other hand, when the iterative space mapping algorithm is used, it converges fast to a design which meets all the specifications. In addition, full-wave FDFD simulations of only a few candidate structures are required before the iterative process is terminated. Use of the space mapping algorithm therefore results in large reductions in the required computation time when compared to any direct optimization method of the fine FDFD model.

Conceptual design of ACB-CP for ITER cryogenic system

NASA Astrophysics Data System (ADS)

Jiang, Yongcheng; Xiong, Lianyou; Peng, Nan; Tang, Jiancheng; Liu, Liqiang; Zhang, Liang

2012-06-01

ACB-CP (Auxiliary Cold Box for Cryopumps) is used to supply the cryopumps system with necessary cryogen in ITER (International Thermonuclear Experimental Reactor) cryogenic distribution system. The conceptual design of ACB-CP contains thermo-hydraulic analysis, 3D structure design and strength checking. Through the thermohydraulic analysis, the main specifications of process valves, pressure safety valves, pipes, heat exchangers can be decided. During the 3D structure design process, vacuum requirement, adiabatic requirement, assembly constraints and maintenance requirement have been considered to arrange the pipes, valves and other components. The strength checking has been performed to crosscheck if the 3D design meets the strength requirements for the ACB-CP.

Customized Contract Training in Community Colleges: Who Really Benefits? Draft.

ERIC Educational Resources Information Center

Pincus, Fred L.

Customized Contract Training (CCT), which involves contracting to design short term, non-credit courses and workshops to meet the training needs of specific employers, is the new buzz-word at community colleges. Though many assume this type of school-business partnership benefits everyone, the potential negative effects on community colleges as…

VERITAS: status c.2005

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weekes, T. C.; Atkins, R. W.; Badran, H. M.

2006-07-11

VERITAS (Very Energetic Radiation Imaging Telescope Array System), is one of a new generation of TeV gamma-ray observatories. The current status of its construction is described here. The first two telescopes and cameras have been completed and meet the design specifications; the full array of four telescopes could be operational by the end of 2006.

Comparative Study of Antenna Elements for TDRSS Enhanced Multiple Access System

NASA Technical Reports Server (NTRS)

Kory, Carol L.; Lambert, Kevin; Acosta, Roberto; Nessel, James

2006-01-01

We compare three antennas, which are candidates for the TDRSS-Continuation enhanced MA array antenna elements. Measured and simulated data show very good agreement for all antenna elements. All of the antennas meet the specifications with the exception of the SBA isolation. However, improvements can likely be made with further design efforts.

A University Library Creates a Digital Repository for Documenting and Disseminating Community Engagement

ERIC Educational Resources Information Center

Miller, William A.; Billings, Marilyn

2012-01-01

Digital repositories are new tools for documenting the accumulated scholarly work produced at academic institutions and disseminating that material broadly via the internet. Digital repositories support all file types and can be adapted to meet the custom design specifications of individual institutions. A section for community engagement…

Skills for Drug-Free Living Curriculum Guide. Future Quest.

ERIC Educational Resources Information Center

de la Garza, Bridget M.; And Others

The Future Quest curriculum is a functional curriculum to teach drug abuse prevention skills to youth with mild disabilities. The curriculum is a one-semester instructional program of lesson plans that incorporate research-based effective teaching practices and are specifically designed to meet the needs of students with learning and behavior…

Advances in Education Research, Winter 1999.

ERIC Educational Resources Information Center

Advances in Education Research, 1999

1999-01-01

This volume presents selected articles related to the impact of early intervention programs. This is part of a two volume set designed to showcase some of the best cutting edge research in these programs. This volume focuses specifically on aspects of the programs that have proven to be most successful in helping students and meeting programmatic…

Improving Seventh Grade Students' Learning of Ratio and Proportion: The Role of Schema-Based Instruction

ERIC Educational Resources Information Center

Jitendra, Asha K.; Star, Jon R.; Starosta, Kristin; Leh, Jayne M.; Sood, Sheetal; Caskie, Grace; Hughes, Cheyenne L.; Mack, Toshi R.

2009-01-01

The present study evaluated the effectiveness of an instructional intervention (schema-based instruction, SBI) that was designed to meet the diverse needs of middle school students by addressing the research literatures from both special education and mathematics education. Specifically, SBI emphasizes the role of the mathematical structure of…

A New Creative Learning Centre at a Girls School in Australia

ERIC Educational Resources Information Center

Bell, Amanda

2007-01-01

Brisbane Girls Grammar School's new Creative Learning Centre was conceived to group arts studies which were previously scattered across the campus and to serve all students as a meeting place and technology hub. The building is specifically designed to provide the most flexible and innovative environment for teenaged girls, having special regard…

24 CFR 3280.403 - Standard for windows and sliding glass doors used in manufactured homes.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Manufactured Housing, except the exterior and interior pressure tests must be conducted at the design wind... the products, an independent quality assurance agency shall conduct pre-production specimen tests in... meet ANSI Z97.1-1984, “Safety Performance Specifications and Methods of Test for Safety Glazing...

24 CFR 3280.403 - Standard for windows and sliding glass doors used in manufactured homes.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Manufactured Housing, except the exterior and interior pressure tests must be conducted at the design wind... the products, an independent quality assurance agency shall conduct pre-production specimen tests in... meet ANSI Z97.1-1984, “Safety Performance Specifications and Methods of Test for Safety Glazing...

24 CFR 3280.403 - Standard for windows and sliding glass doors used in manufactured homes.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Manufactured Housing, except the exterior and interior pressure tests must be conducted at the design wind... the products, an independent quality assurance agency shall conduct pre-production specimen tests in... meet ANSI Z97.1-1984, “Safety Performance Specifications and Methods of Test for Safety Glazing...

24 CFR 3280.403 - Standard for windows and sliding glass doors used in manufactured homes.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Manufactured Housing, except the exterior and interior pressure tests must be conducted at the design wind... the products, an independent quality assurance agency shall conduct pre-production specimen tests in... meet ANSI Z97.1-1984, “Safety Performance Specifications and Methods of Test for Safety Glazing...

Model Adoption Exchange Payment System: Technical Specifications and User Instructions.

ERIC Educational Resources Information Center

Ambrosino, Robert J.

This user's manual, designed to meet the needs of adoption exchange administrators and program managers for a formal tool to assist them in the overall management and operation of their program, presents the Model Adoption Exchange Payment System (MAEPS), which was developed to improve the delivery of adoption exchange services throughout the…

Preschool Music Curricula: Children's Music Development Program.

ERIC Educational Resources Information Center

Levinowitz, Lili Muhler; Gordon, Edwin Elias

These developmental music curricula for preschool children 18 months to 3 years old, 3-year-olds, 4-year-olds, and 5- to 6-year-olds are specifically designed to meet perceptual-motor, cognitive-linguistic, social-emotional, and music needs of children of different ages. Materials provided in this paper include: (1) a rationale for early music…

How to Operate Your Day Care Program.

ERIC Educational Resources Information Center

Jones (Ryan) Associates, Inc., Wyomissing, PA.

Originally written to assist communities in Pennsylvania in the design and implementation of comprehensive child development day care programs to meet Federal Inter-Agency guidelines, this manual is geared to the specific needs of the administrator and is equally valuable for any program, large or small, public or private. Section I is on the…

Commonsense Methods for Children with Special Educational Needs: Strategies for the Regular Classroom. Fourth Edition.

ERIC Educational Resources Information Center

Westwood, Peter

This book is designed to provide teachers with an immediate and comprehensive source of practical strategies for meeting children's special needs in regular classrooms. Chapter 1 explores issues relating to children with general and specific learning difficulties. It discusses inclusive schooling and special educational needs, factors associated…

A Report on Deliverable Six: Develop a Concept Design for a Ruggedized, Lightweight, Portable, Powered Handheld Suction Device

DTIC Science & Technology

reflect it. There are commercially available manual and powered suction devices on the market , and several are specifically advertised for use in...combine to suggest that no device on the market meets even the most basic requirements of being small, lightweight, rugged, and demonstrating adequate

Build a Bird House. Grades 3-5.

ERIC Educational Resources Information Center

Rushton, Erik; Ryan, Emily; Swift, Charles

In this activity, students construct bird nests and birdhouses. Students research a bird of their choice in order to design a house that will meet that bird's specific needs. The activity works well in conjunction with a high school level woodshop class where students would partner up. This activity requires an 80-minute time period for…

Cornerstones: Literacy Units Ready for Teachers, Students

ERIC Educational Resources Information Center

Blasko, Jennifer; Donahue, Sheila

2008-01-01

Every day, teachers face the time-consuming task of adapting materials from curricula that do not meet their students' needs or match their learning styles. This article discusses ready-made literacy units specifically designed for teachers of deaf and hard of hearing students. The units were part of the Cornerstones Project, an activity of the…

Meeting the Challenge of Limited Literacy Resources for Adolescents and Adults with Intellectual Disabilities

ERIC Educational Resources Information Center

Morgan, Michelle F.; Moni, Karen B.

2008-01-01

For adolescents and adults with mild to moderate intellectual disabilities (or, in the UK, learning disabilities or learning difficulties), the achievement of successful engagement with, and construction of meaning from, texts necessitates the implementation and use of specifically designed and adapted teaching strategies and resources. The…

Virtual Learning Environments on the Go: CALL Meets MALL

ERIC Educational Resources Information Center

Arús Hita, Jorge

2016-01-01

This paper presents "Eating out," a Moodle-based digital learning resource for English as a Foreign Language (EFL) teaching that can be run both on computers and mobile devices. It is argued that Mobile Assisted Language Learning (MALL) resources do not necessarily need to be specifically designed for such platforms. Rather, a carefully…

75 FR 346 - Environmental Management Site-Specific Advisory Board, Idaho National Laboratory

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-05

... current agenda): Progress to Cleanup. InSitu Grouting--Draft Remedial Design and Remedial Action Work Plan... this meeting be announced in the Federal Register. DATES: Wednesday, January 20, 2010, 8 a.m.-5 p.m... in the areas of environmental restoration, waste management, and related activities. Tentative Topics...

Faculty Perceptions of Students with Intellectual Disabilities in Public Post Secondary Education

ERIC Educational Resources Information Center

Fisher, Andrew

2008-01-01

Persons with intellectual disabilities have been integrated into post secondary education at increasing rates since the 1990s. Some colleges and universities have responded to the influx of this population by implementing specific programs designed to meet the needs of students who have intellectual disabilities. As many as 138 college campuses…

YAMM - Yet Another Menu Manager

NASA Technical Reports Server (NTRS)

Mazer, Alan S.; Weidner, Richard J.

1991-01-01

Yet Another Menu Manager (YAMM) computer program an application-independent menuing package of software designed to remove much difficulty and save much time inherent in implementation of front ends of large packages of software. Provides complete menuing front end for wide variety of applications, with provisions for independence from specific types of terminals, configurations that meet specific needs of users, and dynamic creation of menu trees. Consists of two parts: description of menu configuration and body of application code. Written in C.

Investigation using data from ERTS to develop and implement utilization of living marine resources

NASA Technical Reports Server (NTRS)

Stevenson, W. H. (Principal Investigator); Pastula, E. J., Jr.

1973-01-01

The author has identified the following significant results. The feasibility of utilizing ERTS-1 data in conjunction with aerial remote sensing and sea truth information to predict the distribution of menhaden in the Mississippi Sound during a specific time frame has been demonstrated by employing a number of uniquely designed empirical regression models. The construction of these models was made possible through innovative statistical routines specifically developed to meet the stated objectives.

Preliminary design of a solar central receiver for site-specific repowering application (Saguaro Power Plant). Volume II. Preliminary design. Final report, October 1982-September 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weber, E.R.

1983-09-01

The solar central receiver technology, site, and specific unit for repowering were selected in prior analyses and studies. The objectives of this preliminary design study were to: develop a solar central receiver repowering design for Saguaro that (1) has potential to be economically competitive with fossil fueled plants in near and long term applications, (2) has the greatest chance for completion without further government funding, (3) will further define technical and economic feasibility of a 66 MWe gross size plant that is adequate to meet the requirements for utility and industrial process heat applications, (4) can potentially be constructed andmore » operated within the next five years, and (5) incorporates solar central receiver technology and represents state-of-the-art development. This volume on the preliminary design includes the following sections: executive summary; introduction; changes from advanced conceptual design; preliminary design; system characteristics; economic analysis; and development plan.« less

Design, optimization, and analysis of a self-deploying PV tent array

NASA Astrophysics Data System (ADS)

Collozza, Anthony J.

1991-06-01

A tent shaped PV array was designed and the design was optimized for maximum specific power. In order to minimize output power variation a tent angle of 60 deg was chosen. Based on the chosen tent angle an array structure was designed. The design considerations were minimal deployment time, high reliability, and small stowage volume. To meet these considerations the array was chosen to be self-deployable, form a compact storage configuration, using a passive pressurized gas deployment mechanism. Each structural component of the design was analyzed to determine the size necessary to withstand the various forces to which it would be subjected. Through this analysis the component weights were determined. An optimization was performed to determine the array dimensions and blanket geometry which produce the maximum specific power for a given PV blanket. This optimization was performed for both lunar and Martian environmental conditions. Other factors such as PV blanket types, structural material, and wind velocity (for Mars array), were varied to determine what influence they had on the design point. The performance specifications for the array at both locations and with each type of PV blanket were determined. These specifications were calculated using the Arimid fiber composite as the structural material. The four PV blanket types considered were silicon, GaAs/Ge, GaAsCLEFT, and amorphous silicon. The specifications used for each blanket represented either present day or near term technology. For both the Moon and Mars the amorphous silicon arrays produced the highest specific power.

POWOW: A Modular, High Power Spacecraft Concept

NASA Technical Reports Server (NTRS)

Brandhorst, Henry W., Jr.

2000-01-01

A robust space infrastructure encompasses a broad range of mission needs along with an imperative to reduce costs of satellites meeting those needs. A critical commodity for science, commercial and civil satellites is power at an affordable cost. The POWOW (POwer WithOut Wires) spacecraft concept was created to provide, at one end of the scale, multi-megawatts of power yet also be composed of modules that can meet spacecraft needs in the kilowatt range. With support from the NASA-sponsored Space Solar Power Exploratory Research and Technology Program, the POWOW spacecraft concept was designed to meet Mars mission needs - while at the same time having elements applicable to a range of other missions. At Mars, the vehicle would reside in an aerosynchronous orbit and beam power to a variety of locations on the surface. It is the purpose of this paper to present the latest concept design results. The Space Power Institute along with four companies: Able Engineering, Inc., Entech, Inc., Primex Aerospace Co., and TECSTAR have produced a modular, power-rich electrically propelled spacecraft design that meets these requirements. In addition, it also meets a range of civil and commercial needs. The spacecraft design is based on multijunction Ill-V solar cells, the new Stretched Lens Aurora (SLA) module, a lightweight array design based on a multiplicity of 8 kW end-of-life subarrays and electric thrusters. The solar cells have excellent radiation resistance and efficiencies above 30%. The SLA has a concentration ratio up to 15x while maintaining an operating temperature of 80 C. The design of the 8 kW array building block will be presented and its applicability to commercial and government missions will be discussed. Electric propulsion options include Hall, MPD and ion thrusters of various power levels and trade studies have been conducted to define the most advantageous options. The present baseline spacecraft design providing 900 kW using technologies expected to be available in 2003 will be described. Areal power densities of nearly 400 W/meters squared at 80 C operating temperatures and wing level specific powers of over 400 W/kg are projected. Details of trip times and payloads to Mars will be presented as well as trade studies of various electric propulsion options. Trip times compare favorably with chemical propulsion options. Because the design is modular, learning curve methodology can be applied to determine expected cost reductions. These results will also be included. This paper has not been presented at a previous meeting.

Environmental control medical support team

NASA Technical Reports Server (NTRS)

Crump, William J.; Kilgore, Melvin V., Jr.

1988-01-01

The activities conducted in support of the Environmental Control and Life Support Team during December 7, 1987 through September 30, 1988 are summarized. The majority of the ongoing support has focused on the ECLSS area. Through a series of initial meetings with the ECLSS team and technical literature review, an initial list of critical topics was developed. Subtasks were then identified or additional related tasks received as action items from the ECLSS group meetings. Although most of the efforts focused on providing MSFC personnel with information regarding specific questions and problems related to ECLSS issues, other efforts regarding identifying an ECLSS Medical Support Team and constructing data bases of technical information were also initiated and completed. The specific tasks are as follows: (1) Provide support to the mechanical design and integration of test systems as related to microbiological concerns; (2) Assist with design of Human Subjects Test Protocols; (3) Interpretation and recommendations pertaining to air/water quality requirements; (4) Assist in determining the design specifications required as related to the Technical Demonstration Program; (5) Develop a data base of all microorganisms recovered from previous subsystem testing; (6) Estimates of health risk of individual microbes to test subjects; (7) Assist with setting limits for safety of test subjects; (8) Health monitoring of test subjects; (9) Assist in the preparation of test plans; (10) Assist in the development of a QA/QC program to assure the validity, accuracy and precision of the analyses; and (11) Assist in developing test plans required for future man in the loop testing.

Patterning vascular networks in vivo for tissue engineering applications.

PubMed

Chaturvedi, Ritika R; Stevens, Kelly R; Solorzano, Ricardo D; Schwartz, Robert E; Eyckmans, Jeroen; Baranski, Jan D; Stapleton, Sarah Chase; Bhatia, Sangeeta N; Chen, Christopher S

2015-05-01

The ultimate design of functionally therapeutic engineered tissues and organs will rely on our ability to engineer vasculature that can meet tissue-specific metabolic needs. We recently introduced an approach for patterning the formation of functional spatially organized vascular architectures within engineered tissues in vivo. Here, we now explore the design parameters of this approach and how they impact the vascularization of an engineered tissue construct after implantation. We used micropatterning techniques to organize endothelial cells (ECs) into geometrically defined "cords," which in turn acted as a template after implantation for the guided formation of patterned capillaries integrated with the host tissue. We demonstrated that the diameter of the cords before implantation impacts the location and density of the resultant capillary network. Inclusion of mural cells to the vascularization response appears primarily to impact the dynamics of vascularization. We established that clinically relevant endothelial sources such as induced pluripotent stem cell-derived ECs and human microvascular endothelial cells can drive vascularization within this system. Finally, we demonstrated the ability to control the juxtaposition of parenchyma with perfused vasculature by implanting cords containing a mixture of both a parenchymal cell type (hepatocytes) and ECs. These findings define important characteristics that will ultimately impact the design of vasculature structures that meet tissue-specific needs.

How Can Health Information Technologies Contribute to Improve Health Care Services for High-Need Patients?

PubMed

Nøhr, Christian; Botin, Lars; Zhu, Xinxin

2017-01-01

This paper discusses how health information technologies like tele-care, tele-health and tele-medicine can improve the condition for high-need patients, specifically in relation to access. The paper addresses specifically the values of timeliness and equity and how tele technological solutions can support and enhance these values. The paper introduces to the concept of scaffolding, which constitutes the framework for dynamic, appropriate, caring and embracing approaches for engaging and involving high-need patients that are vulnerable and exposed. A number of specific considerations for designing tele-technologies for high-need patients are derived, and the paper concludes that ethical and epistemological criterions for design are needed in order to meet the needs and requirements of the weak and exposed.

Repeated significance tests of linear combinations of sensitivity and specificity of a diagnostic biomarker

PubMed Central

Wu, Mixia; Shu, Yu; Li, Zhaohai; Liu, Aiyi

2016-01-01

A sequential design is proposed to test whether the accuracy of a binary diagnostic biomarker meets the minimal level of acceptance. The accuracy of a binary diagnostic biomarker is a linear combination of the marker’s sensitivity and specificity. The objective of the sequential method is to minimize the maximum expected sample size under the null hypothesis that the marker’s accuracy is below the minimal level of acceptance. The exact results of two-stage designs based on Youden’s index and efficiency indicate that the maximum expected sample sizes are smaller than the sample sizes of the fixed designs. Exact methods are also developed for estimation, confidence interval and p-value concerning the proposed accuracy index upon termination of the sequential testing. PMID:26947768

Spacecraft optical disk recorder memory buffer control

NASA Technical Reports Server (NTRS)

Hodson, Robert F.

1993-01-01

This paper discusses the research completed under the NASA-ASEE summer faculty fellowship program. The project involves development of an Application Specific Integrated Circuit (ASIC) to be used as a Memory Buffer Controller (MBC) in the Spacecraft Optical Disk System (SODR). The SODR system has demanding capacity and data rate specifications requiring specialized electronics to meet processing demands. The system is being designed to support Gigabit transfer rates with Terabit storage capability. The complete SODR system is designed to exceed the capability of all existing mass storage systems today. The ASIC development for SODR consist of developing a 144 pin CMOS device to perform format conversion and data buffering. The final simulations of the MBC were completed during this summer's NASA-ASEE fellowship along with design preparations for fabrication to be performed by an ASIC manufacturer.

Transforming patient experience: health web science meets medicine 2.0.

PubMed

McHattie, Lynn-Sayers; Cumming, Grant; French, Tara

2014-01-01

Until recently, the Western biomedical paradigm has been effective in delivering health care, however this model is not positioned to tackle complex societal challenges or solve the current problems facing health care and delivery. The future of medicine requires a shift to a patient-centric model and in so doing the Internet has a significant role to play. The disciplines of Health Web Science and Medicine 2.0 are pivotal to this approach. This viewpoint paper argues that these disciplines, together with the field of design, can tackle these challenges. Drawing together ideas from design practice and research, complexity theory, and participatory action research we depict design as an approach that is fundamentally social and linked to concepts of person-centered care. We discuss the role of design, specifically co-design, in understanding the social, psychological, and behavioral dimensions of illness and the implications for the design of future care towards transforming the patient experience. This paper builds on the presentations and subsequent interdisciplinary dialogue that developed from the panel session "Transforming Patient Experience: Health Web Science Meets Web 2.0" at the 2013 Medicine 2.0 conference in London.

Transforming Patient Experience: Health Web Science Meets Medicine 2.0

PubMed Central

2014-01-01

Until recently, the Western biomedical paradigm has been effective in delivering health care, however this model is not positioned to tackle complex societal challenges or solve the current problems facing health care and delivery. The future of medicine requires a shift to a patient-centric model and in so doing the Internet has a significant role to play. The disciplines of Health Web Science and Medicine 2.0 are pivotal to this approach. This viewpoint paper argues that these disciplines, together with the field of design, can tackle these challenges. Drawing together ideas from design practice and research, complexity theory, and participatory action research we depict design as an approach that is fundamentally social and linked to concepts of person-centered care. We discuss the role of design, specifically co-design, in understanding the social, psychological, and behavioral dimensions of illness and the implications for the design of future care towards transforming the patient experience. This paper builds on the presentations and subsequent interdisciplinary dialogue that developed from the panel session "Transforming Patient Experience: Health Web Science Meets Web 2.0" at the 2013 Medicine 2.0 conference in London. PMID:25075246

Spacecraft design project: High temperature superconducting infrared imaging satellite

NASA Technical Reports Server (NTRS)

1991-01-01

The High Temperature Superconductor Infrared Imaging Satellite (HTSCIRIS) is designed to perform the space based infrared imaging and surveillance mission. The design of the satellite follows the black box approach. The payload is a stand alone unit, with the spacecraft bus designed to meet the requirements of the payload as listed in the statement of work. Specifications influencing the design of the spacecraft bus were originated by the Naval Research Lab. A description of the following systems is included: spacecraft configuration, orbital dynamics, radio frequency communication subsystem, electrical power system, propulsion, attitude control system, thermal control, and structural design. The issues of testing and cost analysis are also addressed. This design project was part of the course Advanced Spacecraft Design taught at the Naval Postgraduate School.

A microdisplay-based HUD for automotive applications: Backplane design, planarization, and optical implementation

NASA Astrophysics Data System (ADS)

Schuck, Miller Harry

Automotive head-up displays require compact, bright, and inexpensive imaging systems. In this thesis, a compact head-up display (HUD) utilizing liquid-crystal-on-silicon microdisplay technology is presented from concept to implementation. The thesis comprises three primary areas of HUD research: the specification, design and implementation of a compact HUD optical system, the development of a wafer planarization process to enhance reflective device brightness and light immunity and the design, fabrication and testing of an inexpensive 640 x 512 pixel active matrix backplane intended to meet the HUD requirements. The thesis addresses the HUD problem at three levels, the systems level, the device level, and the materials level. At the systems level, the optical design of an automotive HUD must meet several competing requirements, including high image brightness, compact packaging, video-rate performance, and low cost. An optical system design which meets the competing requirements has been developed utilizing a fully-reconfigurable reflective microdisplay. The design consists of two optical stages, the first a projector stage which magnifies the display, and a second stage which forms the virtual image eventually seen by the driver. A key component of the optical system is a diffraction grating/field lens which forms a large viewing eyebox while reducing the optical system complexity. Image quality biocular disparity and luminous efficacy were analyzed and results of the optical implementation are presented. At the device level, the automotive HUD requires a reconfigurable, video-rate, high resolution image source for applications such as navigation and night vision. The design of a 640 x 512 pixel active matrix backplane which meets the requirements of the HUD is described. The backplane was designed to produce digital field sequential color images at video rates utilizing fast switching liquid crystal as the modulation layer. The design methodology is discussed, and the example of a clock generator is described from design to implementation. Electrical and optical test results of the fabricated backplane are presented. At the materials level, a planarization method was developed to meet the stringent brightness requirements of automotive HUD's. The research efforts described here have resulted in a simple, low cost post-processing method for planarizing microdisplay substrates based on a spin-cast polymeric resin, benzocyclobutene (BCB). Six- fold reductions in substrate step height were accomplished with a single coating. Via masking and dry etching methods were developed. High reflectivity metal was deposited and patterned over the planarized substrate to produce high aperture pixel mirrors. The process is simple, rapid, and results in microdisplays better able to meet the stringent requirements of high brightness display systems. Methods and results of the post- processing are described.

A Prospective Study of the Concordance of DSM-IV and DSM-5 Diagnostic Criteria for Autism Spectrum Disorder.

PubMed

Mazurek, Micah O; Lu, Frances; Symecko, Heather; Butter, Eric; Bing, Nicole M; Hundley, Rachel J; Poulsen, Marie; Kanne, Stephen M; Macklin, Eric A; Handen, Benjamin L

2017-09-01

The transition from DSM-IV to DSM-5 criteria for autism spectrum disorder (ASD) sparked considerable concern about the potential implications of these changes. This study was designed to address limitations of prior studies by prospectively examining the concordance of DSM-IV and final DSM-5 criteria on a consecutive sample of 439 children referred for autism diagnostic evaluations. Concordance and discordance were assessed using a consistent diagnostic battery. DSM-5 criteria demonstrated excellent overall specificity and good sensitivity relative to DSM-IV criteria. Sensitivity and specificity were strongest for children meeting DSM-IV criteria for autistic disorder, but poor for those meeting criteria for Asperger's disorder and pervasive developmental disorder. Higher IQ, older age, female sex, and less pronounced ASD symptoms were associated with greater discordance.

Multichip module technology for automotive application

NASA Astrophysics Data System (ADS)

Johnson, R. Wayne; Evans, John L.; Bosley, Larry

1995-01-01

Advancements in multichip module technology are creating design freedoms previously unavailable to design engineers. These advancements are opening new markets for laminate based multichip module products. In particular, material improvements in laminate printed wiring boards are allowing multichip module technology to meet more stringent environmental conditions. In addition, improvements in encapsulants and adhesives are enhancing the capabilities of multichip module technology to meet harsh environment. Furthermore, improvements in manufacturing techniques are providing the reliability improvements necessary for use in high quality electronic systems. These advances are making multichip module technology viable for high volume, harsh environment applications like under-the-hood automotive electronics. This paper will provide a brief review of multichip module technology, a discussion of specific research activities with Chrysler for use of multichip modules in automotive engine controllers and finally a discussion of prototype multichip modules fabricated and tested.

The programming language HAL: A specification

NASA Technical Reports Server (NTRS)

1971-01-01

HAL accomplishes three significant objectives: (1) increased readability, through the use of a natural two-dimensional mathematical format; (2) increased reliability, by providing for selective recognition of common data and subroutines, and by incorporating specific data-protect features; (3) real-time control facility, by including a comprehensive set of real-time control commands and signal conditions. Although HAL is designed primarily for programming on-board computers, it is general enough to meet nearly all the needs in the production, verification and support of aerospace, and other real-time applications.

Development Challenges of Utilizing a Corner Cube Mechanism Design with Successful IASI Flight Heritage for the Infrared Sounder (IRS) on MTG: Recurrent Mechanical Design not Correlated to Recurrent Development

NASA Astrophysics Data System (ADS)

Spanoudakis, Peter; Schwab, Philippe; Kiener, Lionel; Saudan, Herve; Perruchoud, Gerald

2015-09-01

The Corner Cube Mechanism (CCM) design for the Infra-Red Sounder (IRS) on MTG is based on the successful mechanism currently in orbit on the Infrared Atmospheric Sounding Interferometers (IASI) on the Metop satellites. The overall CCM performance is described with attention given to the specific design developments for the MTG project. A description is presented of the modifications introduced and challenges encountered to adapt the IASI space heritage design (which is only 15 years old) to meet the MTG specifications. A detailed account is provided regarding the tests performed on the adapted components for the new programme. The major issues encountered and solutions proposed are illustrated concerning the voice- coil actuator development, optical switch design, fatigue life of the flexure components and the adaptation of the launch locking device. Nevertheless, an Engineering Qualification Model was rapidly manufactured and now undergoing a qualification test campaign.

Latch fittings for the scientific instruments on the space telescope

NASA Technical Reports Server (NTRS)

Dozier, J. D.; Kaelber, E.

1983-01-01

Latch fittings which kinematically mount the replaceable scientific instruments onto the Space Telescope must maintain precise alignment and thermal stability for on-orbit observations. Design features which are needed to meet stringent criteria include the use of ceramic isolators for thermal and electrical insulation, materials with different coefficients of thermal expansion for athermalization, precision manufacturing procedures, and extremely tight tolerances. A specific latch fitting to be discussed is a ball-and-socket design. In addition, testing, crew aids, and problems will be covered.

Health and Economic Outcomes in the Alumni of the Wounded Warrior Project: 2010-2012

DTIC Science & Technology

2014-01-01

design a web-based survey that would help the organization evaluate how well it is meeting its three primary strategic goals: • Ensure that wounded...the Primary Care PTSD Screen (PC-PTSD). When responses to all three surveys were pooled into one analysis, they show that the percentage of...relied on a metric in the data, the two-item Connor- Davidson Resilience Scale (CD- RISC  2), a measure specifically designed to quantify an indi

Laser systems for the combustion research facility - Diana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, C.K.; Lavasek, J.W.; Jones, E.D.

1982-03-01

A 5-Joule/pulse, 1.8-..mu..s-pulse-width, 10-ppS flashlamp-pumped tunable-dye-laser system, called Diana, has been built for use in experiments to be performed at the Combustion Research Facility, Sandia National Laboratories, Livermore. Design specifications for the system and details of construction are described, and it is noted that performance of the laser meets or exceeds all design criteria. Areas for further performance improvements are discussed, and updates are suggested to enhance system usefulness.

Solar energy heating system design package for a single-family residence at New Castle, Pennsylvania

NASA Technical Reports Server (NTRS)

1977-01-01

The design of a solar heating and hot water system for a single family dwelling is described. Cost trade studies on the energy conservation and architectural features of the solar house are discussed. The present status of verification for the single family heating system, i.e., proof that the components and the system meet applicable physical and functional requirements, is reported. The system integration drawings, the major subsystems drawings, and the architect's specifications and plans are included.

Identification and status of design improvements to the NASA Shuttle EMU for International Space Station application.

PubMed

Wilde, R C; McBarron, J W; Faszcza, J J

1997-06-01

To meet the significant increase in EVA demand to support assembly and operations of the International Space Station (ISS), NASA and industry have improved the current Shuttle Extravehicular Mobility Unit (EMU), or "space suit", configuration to meet the unique and specific requirements of an orbital-based system. The current Shuttle EMU was designed to be maintained and serviced on the ground between frequent Shuttle flights. ISS will require the EMUs to meet increased EVAs out of the Shuttle Orbiter and to remain on orbit for up to 180 days without need for regular return to Earth for scheduled maintenance or refurbishment. Ongoing Shuttle EMU improvements have increased reliability, operational life and performance while minimizing ground and on-orbit maintenance cost and expendable inventory. Modifications to both the anthropomorphic mobility elements of the Space Suit Assembly (SSA) as well as to the Primary Life Support System (PLSS) are identified and discussed. This paper also addresses the status of on-going Shuttle EMU improvements and summarizes the approach for increasing interoperability of the U.S. and Russian space suits to be utilized aboard the ISS.

Adequate number of clinicians on usability tests lacking, says study.

PubMed

2015-12-01

A new study reveals that some of the largest EMR vendors failed to meet certification standards, specifying that they state their user-centered design processes, and that they include at least 15 representative end-user participants in their usability tests. It is not clear why these vendors were certified despite not meeting the standards established by Office of the National Coordinator for Health Information Technology (ONC), but investigators suggest that emergency clinicians and administrators should engage with vendors early on, querying them about their user-centered processes. An analysis of the usability tests performed by 41 of some the largest EMR vendors found that 34% of them did not meet certification standards, specifying that they state their user-centered design process. Also, 63% of the vendors failed to include at least 15 representative end-users in their usability tests. Only 15% of the vendors used at least 15 participants who had clinical backgrounds in their usability tests. Experts urge clinicians to engage with EMR user groups to share best practices for optimizing specific EMR products.

RT-Syn: A real-time software system generator

NASA Technical Reports Server (NTRS)

Setliff, Dorothy E.

1992-01-01

This paper presents research into providing highly reusable and maintainable components by using automatic software synthesis techniques. This proposal uses domain knowledge combined with automatic software synthesis techniques to engineer large-scale mission-critical real-time software. The hypothesis centers on a software synthesis architecture that specifically incorporates application-specific (in this case real-time) knowledge. This architecture synthesizes complex system software to meet a behavioral specification and external interaction design constraints. Some examples of these external constraints are communication protocols, precisions, timing, and space limitations. The incorporation of application-specific knowledge facilitates the generation of mathematical software metrics which are used to narrow the design space, thereby making software synthesis tractable. Success has the potential to dramatically reduce mission-critical system life-cycle costs not only by reducing development time, but more importantly facilitating maintenance, modifications, and extensions of complex mission-critical software systems, which are currently dominating life cycle costs.

LST and instrument considerations. [modular design

NASA Technical Reports Server (NTRS)

Levin, G. M.

1974-01-01

In order that the LST meet its scientific objectives and also be a National Astronomical Space Facility during the 1980's and 1990's, broad requirements have been levied by the scientific community. These scientific requirements can be directly translated into design requirements and specifications for the scientific instruments. The instrument ensemble design must be consistent with a 15-year operational lifetime. Downtime for major repair/refurbishment or instrument updating must be minimized. The overall efficiency and performance of the instruments should be maximized. Modularization of instruments and instrument subsystems, some degree of on-orbit servicing (both repair and replacement), on-axis location, minimizing the number of reflections within instruments, minimizing polarization effects, and simultaneous operation of the F/24 camera with other instruments, are just a few of the design guidelines and specifications which can and will be met in order that these broader scientific requirements be satisfied.-

South Carolina Guide for Mathematics for the Technologies (Applied Vocational Mathematics).

ERIC Educational Resources Information Center

Moore, Charles; And Others

In this instructional guide, a third-level, two-semester mathematics course specifically for the student who plans a career in a vocational field is presented. The course is designed to meet the needs of students with varying mathematical backgrounds and to teach the mathematical skills required by various technical areas. In this practical…

Health Education in Elementary Schools. Curriculum Bulletin, 1969-70 Series. Number 2.

ERIC Educational Resources Information Center

New York City Board of Education, Brooklyn, NY. Bureau of Curriculum Development.

This publication serves as a basic instrument for health instruction in the elementary grades. It has been designed for adaptation in meeting the differing needs of New York City pupils. The format of the bulletin enables the teacher to plan specific lessons with health learning supplemented by recommended pupil activities through a basic set up…

Consistent indicators and methods and a scalable sample design to meet assessment, inventory, and monitoring information needs across scales

USDA-ARS?s Scientific Manuscript database

Within the Bureau of Land Management (BLM), as in many land management agencies throughout the world, much effort is invested in monitoring and assessment for specific management needs. The BLM Assessment, Inventory, and Monitoring (AIM) Strategy was initiated, in part, to evaluate and make recommen...

Project visual analysis for the Allegheny National Forest

Treesearch

Gary W. Kell

1979-01-01

The Project Visual Analysis is a landscape assessment procedure involving forest vegetative manipulation. A logical step by step analysis leads the user to a specific set of landscape management guidelines to be used as an aid in designing a project or in evaluating whether the proposed project impacts will meet visual objectives. Key elements within the procedure are...

Engaging in Continuing Education and Training: Learning Preferences of Worker-Learners in the Health and Community Services Industry

ERIC Educational Resources Information Center

Choy, Sarojni; Billett, Stephen; Kelly, Ann

2013-01-01

Current tertiary education and training provisions are designed mainly to meet the learning needs of those preparing for entry into employment and specific occupations. Yet, changing work, new work requirements, an ageing workforce and the ongoing need for employability across lengthening working lives make it imperative that this educational…

Moving from the Margins: Culturally Safe Teacher Education in Remote Northwestern British Columbia

ERIC Educational Resources Information Center

Harrison, Edward B.; Lautensach, Alexander K.; McDonald, Verna Lynn

2012-01-01

In 2007 the University of Northern British Columbia initiated a two-year elementary teacher education program at the Northwest Campus in Terrace, British Columbia. The program was designed to meet specific community needs in the North that arise from inequities in the cultural safety of Indigenous teachers and students. The authors share three…

The Inclusive Classroom Profile (ICP) Preliminary Findings of Demonstration Study in North Carolina

ERIC Educational Resources Information Center

Soukakou, E.; Winton, P.; West, T.

2012-01-01

The Inclusive Classroom Profile (ICP) was developed in response to a lack of validated instruments designed specifically to measure the quality of inclusive practices, and it is based on research evidence on the effectiveness of specialized instructional strategies for meeting the individual needs of children in inclusive settings (Odom, 2004;…

We're in This Together: Creating Synergies with Collaborative Ventures

ERIC Educational Resources Information Center

Fulton, Tara Lynn

2012-01-01

Academic libraries by nature serve as spaces for communities of learners to gather. Careful design and marketing of spaces to meet specific needs, staffed by experts to facilitate and guide such learning, enhance the impact of "library as place." In this article, the author shares two examples of collaborations that have resulted from partnerships…

41 CFR 102-76.25 - What standards must Federal agencies meet in providing architectural and interior design services?

Code of Federal Regulations, 2012 CFR

2012-01-01

... Public Contracts and Property Management Federal Property Management Regulations System (Continued... accordance with the standards in § 102-76.65. (c) Use metric specifications in construction where the metric system is the accepted industry standard, and to the extent that such usage is economically feasible and...

41 CFR 102-76.25 - What standards must Federal agencies meet in providing architectural and interior design services?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Public Contracts and Property Management Federal Property Management Regulations System (Continued... accordance with the standards in § 102-76.65. (c) Use metric specifications in construction where the metric system is the accepted industry standard, and to the extent that such usage is economically feasible and...

41 CFR 102-76.25 - What standards must Federal agencies meet in providing architectural and interior design services?

Code of Federal Regulations, 2011 CFR

2011-01-01

... Public Contracts and Property Management Federal Property Management Regulations System (Continued... accordance with the standards in § 102-76.65. (c) Use metric specifications in construction where the metric system is the accepted industry standard, and to the extent that such usage is economically feasible and...

41 CFR 102-76.25 - What standards must Federal agencies meet in providing architectural and interior design services?

Code of Federal Regulations, 2014 CFR

2014-01-01

... Public Contracts and Property Management Federal Property Management Regulations System (Continued... accordance with the standards in § 102-76.65. (c) Use metric specifications in construction where the metric system is the accepted industry standard, and to the extent that such usage is economically feasible and...

Fort Berthold Library Literacy Program. Final Performance Report, October 1, 1988-September 30, 1989.

ERIC Educational Resources Information Center

Fort Berthold Reservation Public Library, New Town, ND.

The report describes activities of the Fort Berthold Reservation Public Library (North Dakota) Literacy Program to meet six objectives for the 1988-89 project year. The program was designed specifically to promote literacy among three Native American tribes, the Mandan, Hidatsa, and Arikara. Objectives included acquisition of a library literacy…

76 FR 80915 - Environmental Management Site-Specific Advisory Board, Northern New Mexico

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-27

...), Ed Worth and Lee Bishop Welcome and Introductions, Ralph Phelps 3:15 p.m. Environmental Cleanup.... Consent Order Update 6 p.m. Public Comment Period, Ralph Phelps 7 p.m. Adjourn, Lee Bishop and Ed Worth... presentation in the agenda. The Deputy Designated Federal Officer is empowered to conduct the meeting in a...

When We Review the National Visual Arts Standards

ERIC Educational Resources Information Center

Herberholz, Barbara

2010-01-01

The National Art Education Association (NAEA) has clearly defined the role of art with six content and achievement standards that are broad in coverage and designed specifically to ensure a thorough and comprehensive art program for K-4, 5-8 and 9-12. To meet the standards, students learn vocabularies and concepts associated with various types of…

The Medically Fragile Child: Caring for Children with Special Healthcare Needs in the School Setting

ERIC Educational Resources Information Center

American Federation of Teachers (NJ), 2009

2009-01-01

This publication is designed to help teachers, nurses and paraprofessionals meet the challenges of dealing with children who have serious medical problems. It contains information on training, health and safety, and legal rights and responsibilities. Specifically, this third edition sets out to accomplish three goals: (1) to educate American…

Middle School Curriculum, Instruction, and Assessment. The Handbook of Research in Middle Level Education.

ERIC Educational Resources Information Center

Anfara, Vincent A., Jr., Ed.; Stacki, Sandra L., Ed.

This volume theorizes, describes, and explains practices and some specific programs designed to help meet the needs and demands of a diverse student population. The central point of this volume is that curriculum, instruction, and assessment in middle-level education is a dynamic, interrelated system undergoing change. The book contains the…

Republication of "Experiencing Management: A Comprehensive, 'Hands-On' Model for the Introductory Undergraduate Management Course"

ERIC Educational Resources Information Center

Miller, John A.

2017-01-01

The purpose of this article is to describe an experiential course designed to overcome the specific problems inherent in working with undergraduate students in introductory management courses. The article grew out of discussions among faculty at the 1988 Academy of Management meetings who shared deep concerns about the quality of undergraduate…

Fire Safety: Stop the Heat. Fourth Grade. Fire Safety for Texans: Fire and Burn Prevention Curriculum Guide.

ERIC Educational Resources Information Center

Texas State Commission on Fire Protection, Austin.

This booklet comprises the fourth grade component of a series of curriculum guides on fire and burn prevention. Designed to meet the age-specific needs of fourth grade students, its objectives include: (1) understanding principles of extinguishing fires, (2) investigating issues of peer pressure related to fire setting, (3) developing…

Fire Safe Together. Kindergarten. Fire Safety for Texans: Fire and Burn Prevention Curriculum Guide.

ERIC Educational Resources Information Center

Texas State Commission on Fire Protection, Austin.

This booklet comprises the kindergarten component of a series of curriculum guides on fire and burn prevention. Designed to meet the age-specific needs of kindergarten students, its objectives include developing basic awareness of fire and burn dangers, developing simple actions to reduce injury, and encouraging parent involvement. Texas essential…

24 CFR 3280.904 - Specific requirements for designing the transportation system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... the tire and manufactured home frame or structure to permit unimpeded wheel movement and for changing... alternatives listed in § 3280.903(c) may be accepted in place of such an analysis. (7) Hubs and bearings. Hubs...) Tires, wheels and rims. Tires, wheels and rims shall meet the requirements of § 3280.904(b)(3). Tires...

24 CFR 3280.904 - Specific requirements for designing the transportation system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... the tire and manufactured home frame or structure to permit unimpeded wheel movement and for changing... alternatives listed in § 3280.903(c) may be accepted in place of such an analysis. (7) Hubs and bearings. Hubs...) Tires, wheels and rims. Tires, wheels and rims shall meet the requirements of § 3280.904(b)(3). Tires...

24 CFR 3280.904 - Specific requirements for designing the transportation system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... the tire and manufactured home frame or structure to permit unimpeded wheel movement and for changing... alternatives listed in § 3280.903(c) may be accepted in place of such an analysis. (7) Hubs and bearings. Hubs...) Tires, wheels and rims. Tires, wheels and rims shall meet the requirements of § 3280.904(b)(3). Tires...

24 CFR 3280.904 - Specific requirements for designing the transportation system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... the tire and manufactured home frame or structure to permit unimpeded wheel movement and for changing... alternatives listed in § 3280.903(c) may be accepted in place of such an analysis. (7) Hubs and bearings. Hubs...) Tires, wheels and rims. Tires, wheels and rims shall meet the requirements of § 3280.904(b)(3). Tires...

Design and Development of Lateral Flight Director

NASA Technical Reports Server (NTRS)

Kudlinski, Kim E.; Ragsdale, William A.

1999-01-01

The current control law used for the flight director in the Boeing 737 simulator is inadequate with large localizer deviations near the middle marker. Eight different control laws are investigated. A heuristic method is used to design control laws that meet specific performance criteria. The design of each is described in detail. Several tests were performed and compared with the current control law for the flight director. The goal was to design a control law for the flight director that can be used with large localizer deviations near the middle marker, which could be caused by winds or wake turbulence, without increasing its level of complexity.

Design of space-type electronic power transformers

NASA Technical Reports Server (NTRS)

Ahearn, J. F.; Lagadinos, J. C.

1977-01-01

Both open and encapsulated varieties of high reliability, low weight, and high efficiency moderate and high voltage transformers were investigated to determine the advantages and limitations of their construction in the ranges of power and voltage required for operation in the hard vacuum environment of space. Topics covered include: (1) selection of the core material; (2) preliminary calculation of core dimensions; (3) selection of insulating materials including magnet wire insulation, coil forms, and layer and interwinding insulation; (4) coil design; (5) calculation of copper losses, core losses and efficiency; (6) calculation of temperature rise; and (7) optimization of design with changes in core selection or coil design as required to meet specifications.

A cost effective method of meeting emission requirements from a 50 MMscfd glycol dehydrator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gearhart, L.E.

1998-12-31

The removal of volatile organic compounds (VOC) and benzene, toluene, ethylbenzene, xylene (BTEX) from glycol dehydration systems does not require costly equipment or elaborate controls. This paper will describe the design and installation of a 10 equivalent try glycol dehydration unit for field gas dehydration. The absorber design minimizes the absorption of VOC and BTEX by requiring 1.0 to 1.5 gallons of glycol per pound of water removed. Glycol unit VOC emissions are effectively controlled without installing vent gas condensers which require disposal of the waste condensate. The emission control system on this unit is simple to operate, meets emissionmore » standards and the dehydrator design achieves pipeline sales gas specifications at a reasonable cost. The system reduces the VOC and BTEX by adding a stripper on the glycol going to the reboiler. A 50 MMscfd dehydrator was installed in December 1995 and the results of an emission test done in April 1997 are presented in this paper.« less

Identifying Key Components for an Effective Case Report Poster: An Observational Study

PubMed Central

Paranjape, Anuradha; Estrada, Carlos

2008-01-01

BACKGROUND Residents demonstrate scholarly activity by presenting posters at academic meetings. Although recommendations from national organizations are available, evidence identifying which components are most important is not. OBJECTIVE To develop and test an evaluation tool to measure the quality of case report posters and identify the specific components most in need of improvement. DESIGN Faculty evaluators reviewed case report posters and provided on-site feedback to presenters at poster sessions of four annual academic general internal medicine meetings. A newly developed ten-item evaluation form measured poster quality for specific components of content, discussion, and format (5-point Likert scale, 1 = lowest, 5 = highest). Main outcome measure(s): Evaluation tool performance, including Cronbach alpha and inter-rater reliability, overall poster scores, differences across meetings and evaluators and specific components of the posters most in need of improvement. RESULTS Forty-five evaluators from 20 medical institutions reviewed 347 posters. Cronbach’s alpha of the evaluation form was 0.84 and inter-rater reliability, Spearman’s rho 0.49 ( < 0.001). The median score was 4.1 (Q1 -Q3, 3.7-4.6)(Q1 = 25th, Q3 = 75th percentile). The national meeting median score was higher than the regional meetings (4.4 vs, 4.0,  < 0.001). We found no difference in faculty scores. The following areas were identified as most needing improvement: clearly state learning objectives, tie conclusions to learning objectives, and use appropriate amount of words. CONCLUSIONS Our evaluation tool provides empirical data to guide trainees as they prepare posters for presentation which may improve poster quality and enhance their scholarly productivity. PMID:19089510

UML activity diagrams in requirements specification of logic controllers

NASA Astrophysics Data System (ADS)

Grobelna, Iwona; Grobelny, Michał

2015-12-01

Logic controller specification can be prepared using various techniques. One of them is the wide understandable and user-friendly UML language and its activity diagrams. Using formal methods during the design phase increases the assurance that implemented system meets the project requirements. In the approach we use the model checking technique to formally verify a specification against user-defined behavioral requirements. The properties are usually defined as temporal logic formulas. In the paper we propose to use UML activity diagrams in requirements definition and then to formalize them as temporal logic formulas. As a result, UML activity diagrams can be used both for logic controller specification and for requirements definition, what simplifies the specification and verification process.

Study of multiple cycles valves

NASA Technical Reports Server (NTRS)

Wichmann, H.

1973-01-01

A discussion is presented regarding valves which can be cycled repeatedly and are available from industry for application in the inlet system for the Pioneer Venus Probe mass spectrometer. Both solenoid type and latching type valves are considered. The study is divided into two principal areas: (1) preparation of a valve specification reflecting the requirements of the inlet system cyclic valves for the Pioneer Venus Probe mass spectrometer and the submittal of this specification to potential valve suppliers for their response and proposal; (2) preparation of a design layout of an optimum cyclic valve meeting all of the valve specification requirements.

Space station wardroom habitability and equipment study

NASA Technical Reports Server (NTRS)

Nixon, David; Miller, Christopher; Fauquet, Regis

1989-01-01

Experimental designs in life-size mock-up form for the wardroom facility for the Space Station Habitability Module are explored and developed. In Phase 1, three preliminary concepts for the wardroom configuration are fabricated and evaluated. In Phase 2, the results of Phase 1 are combined with a specific range of program design requirements to provide the design criteria for the fabrication of an innovative medium-fidelity mock-up of a wardrobe configuration. The study also focuses on the design and preliminary prototyping of selected equipment items including crew exercise compartments, a meal/meeting table and a portable workstation. Design criteria and requirements are discussed and documented. Preliminary and final mock-ups and equipment prototypes are described and illustrated.

A Way to Select Electrical Sheets of the Segment Stator Core Motors.

NASA Astrophysics Data System (ADS)

Enomoto, Yuji; Kitamura, Masashi; Sakai, Toshihiko; Ohara, Kouichiro

The segment stator core, high density winding coil, high-energy-product permanent magnet are indispensable technologies in the development of a compact and also high efficient motors. The conventional design method for the segment stator core mostly depended on experienced knowledge of selecting a suitable electromagnetic material, far from optimized design. Therefore, we have developed a novel design method in the selection of a suitable electromagnetic material based on the correlation evaluation between the material characteristics and motor performance. It enables the selection of suitable electromagnetic material that will meet the motor specification.

Tradeoffs in Capstone Design Courses Involving More Than One Discipline [Senior Design].

PubMed

Goldberg, Jay

2017-01-01

According to a 2015 survey, 5% of capstone design course instructors indicated that their courses involve students from more than one engineering discipline [1]. Students in these courses may hear presentations on topics of common interest and work together on project teams that require knowledge and skills from more than one discipline. Some courses make use of occasional breakout sessions in which discipline-specific topics (such as U.S. Food and Drug Administration regulations) of greater value to students in a particular discipline are presented during class sessions where only students of that discipline meet [2].

The ARCO 1 megawatt Photovoltaic Power Plant

NASA Astrophysics Data System (ADS)

Rhodes, G. W.; Reilly, M. R.

The world's largest Photovoltaic Power Plant is in operation and meeting performance specifications on the Southern California Edison (SCE) grid near Hesperia, California. The 1 MW plant designed and constructed by The BDM Corporation, for ARCO Solar Inc., occupies a 20 acre site adjacent to the SCE Lugo substation. The entire design and construction process took 7 1/2 months and was not only on schedule but below budget. Because of its vast photovoltaic experience, BDM was chosen over several engineering firms to perform this complex job. We were provided a conceptual design from ARCO which we quickly refined and immediately initiated construction.

Embedding a pedagogical model in the design of an online course.

PubMed

Sternberger, Carol S

2002-01-01

The importance of course design and its relationship to learning is overlooked when the electronic version of a course is static. The author discusses the process used to redesign a traditional course into a dynamic and interactive Web-based course by using a pedagogical model developed specifically for hypermedia. Congruence between the instructional methods and the media is a must for a successful design that meets the needs of a wide variety of learners. The hyperlearning model, Dimensions, provides the infrastructure to facilitate the congruence of methods and media while supporting multiple learning styles.

Optimization of scaffold design for bone tissue engineering: A computational and experimental study.

PubMed

Dias, Marta R; Guedes, José M; Flanagan, Colleen L; Hollister, Scott J; Fernandes, Paulo R

2014-04-01

In bone tissue engineering, the scaffold has not only to allow the diffusion of cells, nutrients and oxygen but also provide adequate mechanical support. One way to ensure the scaffold has the right properties is to use computational tools to design such a scaffold coupled with additive manufacturing to build the scaffolds to the resulting optimized design specifications. In this study a topology optimization algorithm is proposed as a technique to design scaffolds that meet specific requirements for mass transport and mechanical load bearing. Several micro-structures obtained computationally are presented. Designed scaffolds were then built using selective laser sintering and the actual features of the fabricated scaffolds were measured and compared to the designed values. It was possible to obtain scaffolds with an internal geometry that reasonably matched the computational design (within 14% of porosity target, 40% for strut size and 55% for throat size in the building direction and 15% for strut size and 17% for throat size perpendicular to the building direction). These results support the use of these kind of computational algorithms to design optimized scaffolds with specific target properties and confirm the value of these techniques for bone tissue engineering. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Survey evaluation and design (SED): A case study in Garden Banks, Gulf of Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, G.; Hannan, A.; Mann, A.D.

1995-12-31

Hydrocarbon exploration in the Gulf of Mexico has reached its mature stages. Exploration objectives such as deep stratigraphic and pre-salt traps are becoming more dominant. As the exploration targets change, earlier 3D seismic surveys, designed for different objectives, become less able to meet the demands of the present day explorations. Some areas of the Gulf of Mexico will require reacquisition of new 3D seismic data, redesigned to meet new objectives. Garden Banks is one such area. A major advantage of performing a survey evaluation design (SED) in a mature area is the amount and diversity of available data. Geological profiles,more » reservoir characterizations, borehole wireline and surface seismic data, all serve to aid in the survey design. Given the exploration history and geological objectives, the geophysical analyses of resolution, signal loss, noise, fold, acquisition geometry, migration aperture, velocity anisotropy and others, may now be carried out in a much more specific manner. A thorough SED ensures that overall survey objectives will be met and reduces the possibility of over design on critical parameters. This generates the highest quality seismic survey for the most reasonable cost.« less

Integrated control design for driver assistance systems based on LPV methods

NASA Astrophysics Data System (ADS)

Gáspár, Péter; Németh, Balázs

2016-12-01

The paper proposes a control design method for a driver assistance system. In the operation of the system, a predefined trajectory required by the driver with a steering command is followed. During manoeuvres the control system generates differential brake moment and the auxiliary front-wheel steering angle and changes the camber angles of the wheels in order to improve the tracking of the road trajectory. The performance specifications are guaranteed by the local controllers, i.e. the brake, the steering, and the suspension systems, while the coordination of these components is provided by the supervisor. The advantage of this architecture is that local controllers are designed independently, which is ensured by the fact that the monitoring signals are taken into consideration in the formalisation of their performance specifications. The fault-tolerant control can be achieved by incorporating the detected fault signals in their performance specifications. The control system also uses a driver model, with which the reference signal can be generated. In the control design, the parameter-dependent linear parameter-varyingmethod, which meets the performance specifications, is used. The operation of the control system is illustrated through different normal and emergency vehicle manoeuvres with a high-accuracy simulation software.

41 CFR 102-76.25 - What standards must Federal agencies meet in providing architectural and interior design services?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Federal agencies meet in providing architectural and interior design services? 102-76.25 Section 102-76.25...) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 76-DESIGN AND CONSTRUCTION Design and Construction § 102-76.25 What standards must Federal agencies meet in providing architectural and interior design services...

Cost-effective technology advancement directions for electric propulsion transportation systems in earth-orbital missions

NASA Technical Reports Server (NTRS)

Regetz, J. D., Jr.; Terwilliger, C. H.

1979-01-01

The directions that electric propulsion technology should take to meet the primary propulsion requirements for earth-orbital missions in the most cost effective manner are determined. The mission set requirements, state of the art electric propulsion technology and the baseline system characterized by it, adequacy of the baseline system to meet the mission set requirements, cost optimum electric propulsion system characteristics for the mission set, and sensitivities of mission costs and design points to system level electric propulsion parameters are discussed. The impact on overall costs than specific masses or costs of propulsion and power systems is evaluated.

Planning and setting objectives in field studies: Chapter 2

USGS Publications Warehouse

Fisher, Robert N.; Dodd, C. Kenneth

2016-01-01

This chapter enumerates the steps required in designing and planning field studies on the ecology and conservation of reptiles, as these involve a high level of uncertainty and risk. To this end, the chapter differentiates between goals (descriptions of what one intends to accomplish) and objectives (the measurable steps required to achieve the established goals). Thus, meeting a specific goal may require many objectives. It may not be possible to define some of them until certain experiments have been conducted; often evaluations of sampling protocols are needed to increase certainty in the biological results. And if sampling locations are fixed and sampling events are repeated over time, then both study-specific covariates and sampling-specific covariates should exist. Additionally, other critical design considerations for field study include obtaining permits, as well as researching ethics and biosecurity issues.

Robust Control Design via Linear Programming

NASA Technical Reports Server (NTRS)

Keel, L. H.; Bhattacharyya, S. P.

1998-01-01

This paper deals with the problem of synthesizing or designing a feedback controller of fixed dynamic order. The closed loop specifications considered here are given in terms of a target performance vector representing a desired set of closed loop transfer functions connecting various signals. In general these point targets are unattainable with a fixed order controller. By enlarging the target from a fixed point set to an interval set the solvability conditions with a fixed order controller are relaxed and a solution is more easily enabled. Results from the parametric robust control literature can be used to design the interval target family so that the performance deterioration is acceptable, even when plant uncertainty is present. It is shown that it is possible to devise a computationally simple linear programming approach that attempts to meet the desired closed loop specifications.

High voltage and current, gate assisted, turn-off thyristor development

NASA Technical Reports Server (NTRS)

Nowalk, T. P.; Brewster, J. B.; Kao, Y. C.

1972-01-01

An improved high speed power switch with unique turn-off capability was developed. This gate assisted turn-off thyristor (GATT) was rated 1000 volts and 100 amperes with turn-off times of 2 microseconds. Fifty units were delivered for evaluation. In addition, test circuits designed to relate to the series inverter application were built and demonstrated. In the course of this work it was determined that the basic device design is adequate to meet the static characteristics and dynamic turn-off specification. It was further determined that the turn-on specification is critically dependent on the gate drive circuit due to the distributive nature of the cathode-gate geometry. Future work should emphasize design modifications which reduce the gate current required for fast turn-on, thereby opening the way to higher power (current) devices.

Redirecting T-cell specificity by introducing a tumor-specific chimeric antigen receptor

PubMed Central

Jena, Bipulendu; Dotti, Gianpietro

2010-01-01

Infusions of antigen-specific T cells have yielded therapeutic responses in patients with pathogens and tumors. To broaden the clinical application of adoptive immunotherapy against malignancies, investigators have developed robust systems for the genetic modification and characterization of T cells expressing introduced chimeric antigen receptors (CARs) to redirect specificity. Human trials are under way in patients with aggressive malignancies to test the hypothesis that manipulating the recipient and reprogramming T cells before adoptive transfer may improve their therapeutic effect. These examples of personalized medicine infuse T cells designed to meet patients' needs by redirecting their specificity to target molecular determinants on the underlying malignancy. The generation of clinical grade CAR+ T cells is an example of bench-to-bedside translational science that has been accomplished using investigator-initiated trials operating largely without industry support. The next-generation trials will deliver designer T cells with improved homing, CAR-mediated signaling, and replicative potential, as investigators move from the bedside to the bench and back again. PMID:20439624

Designing Successful Professional Meetings and Conferences in Education: Planning, Implementation, and Evaluation.

ERIC Educational Resources Information Center

Mundry, Susan; Britton, Edward; Raizen, Senta; Loucks-Horsley, Susan

This book outlines the principles of planning, implementing, and evaluating successful professional meetings and conferences in education. The following are among the topics discussed: (1) the knowledge base of effective meetings and conferences (nine principles held by effective meeting designers; characteristics of effective meetings and…

Design and test of aircraft engine isolators for reduced interior noise

NASA Technical Reports Server (NTRS)

Unruh, J. F.; Scheidt, D. C.

1982-01-01

Improved engine vibration isolation was proposed to be the most weight and cost efficient retrofit structure-borne noise control measure for single engine general aviation aircraft. A study was carried out the objectives: (1) to develop an engine isolator design specification for reduced interior noise transmission, (2) select/design candidate isolators to meet a 15 dB noise reduction design goal, and (3) carry out a proof of concept evaluation test. Analytical model of the engine, vibration isolators and engine mount structure were coupled to an empirical model of the fuselage for noise transmission evaluation. The model was used to develop engine isolator dynamic properties design specification for reduced noise transmission. Candidate isolators ere chosen from available product literature and retrofit to a test aircraft. A laboratory based test procedure was then developed to simulate engine induced noise transmission in the aircraft for a proof of concept evaluation test. Three candidate isolator configurations were evaluated for reduced structure-borne noise transmission relative to the original equipment isolators.

Use of Non-Apical Assay Data in an Integrated Approach to ...

EPA Pesticide Factsheets

This speaker abstract is part of a session proposal for the 2018 Society of Toxicology annual meeting. I am proposing to speak about the use of new approach methods and data, such as AOPs, in mixtures risk assessment. I have developed an innovative approach called AOP footprinting that I intend to present at this meeting. This speaker abstract is part of a session proposal for the 2018 Society of Toxicology annual meeting. Drs. Margaret Pratt (NCEA-IRIS) and Cynthia Rider (NIEHS) are the co-chairs of the proposed session which is designed to present information related to mixtures risk assessment of environmental chemicals, such as PAHs. I have specifically been asked to speak about the use of 21st century toxicity information in human health assessment (e.g., assay data from novel data streams).

HB-LINE ANION EXCHANGE PURIFICATION OF AFS-2 PLUTONIUM FOR MOX

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kyser, E. A.; King, W. D.

2012-07-31

Non-radioactive cerium (Ce) and radioactive plutonium (Pu) anion exchange column experiments using scaled HB-Line designs were performed to investigate the feasibility of using either gadolinium nitrate (Gd) or boric acid (B as H{sub 3}BO{sub 3}) as a neutron poison in the H-Canyon dissolution process. Expected typical concentrations of probable impurities were tested and the removal of these impurities by a decontamination wash was measured. Impurity concentrations are compared to two specifications - designated as Column A or Column B (most restrictive) - proposed for plutonium oxide (PuO{sub 2}) product shipped to the Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF). Usemore » of Gd as a neutron poison requires a larger volume of wash for the proposed Column A specification. Since boron (B) has a higher proposed specification and is more easily removed by washing, it appears to be the better candidate for use in the H-Canyon dissolution process. Some difficulty was observed in achieving the Column A specification due to the limited effectiveness that the wash step has in removing the residual B after ~4 BV's wash. However a combination of the experimental 10 BV's wash results and a calculated DF from the oxalate precipitation process yields an overall DF sufficient to meet the Column A specification. For those impurities (other than B) not removed by 10 BV's of wash, the impurity is either not expected to be present in the feedstock or process, or recommendations have been provided for improvement in the analytical detection/method or validation of calculated results. In summary, boron is recommended as the appropriate neutron poison for H-Canyon dissolution and impurities are expected to meet the Column A specification limits for oxide production in HB-Line.« less

HB-LINE ANION EXCHANGE PURIFICATION OF AFS-2 PLUTONIUM FOR MOX

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kyser, E.; King, W.

2012-04-25

Non-radioactive cerium (Ce) and radioactive plutonium (Pu) anion exchange column experiments using scaled HB-Line designs were performed to investigate the feasibility of using either gadolinium nitrate (Gd) or boric acid (B as H{sub 3}BO{sub 3}) as a neutron poison in the H-Canyon dissolution process. Expected typical concentrations of probable impurities were tested and the removal of these impurities by a decontamination wash was measured. Impurity concentrations are compared to two specifications - designated as Column A or Column B (most restrictive) - proposed for plutonium oxide (PuO{sub 2}) product shipped to the Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF). Usemore » of Gd as a neutron poison requires a larger volume of wash for the proposed Column A specification. Since boron (B) has a higher proposed specification and is more easily removed by washing, it appears to be the better candidate for use in the H-Canyon dissolution process. Some difficulty was observed in achieving the Column A specification due to the limited effectiveness that the wash step has in removing the residual B after {approx}4 BV's wash. However a combination of the experimental 10 BV's wash results and a calculated DF from the oxalate precipitation process yields an overall DF sufficient to meet the Column A specification. For those impurities (other than B) not removed by 10 BV's of wash, the impurity is either not expected to be present in the feedstock or process, or recommendations have been provided for improvement in the analytical detection/method or validation of calculated results. In summary, boron is recommended as the appropriate neutron poison for H-Canyon dissolution and impurities are expected to meet the Column A specification limits for oxide production in HB-Line.« less

Development of advanced high temperature in-cylinder components and tribological systems for low heat rejection diesel engines, phase 1

NASA Astrophysics Data System (ADS)

Kroeger, C. A.; Larson, H. J.

1992-03-01

Analysis and concept design work completed in Phase 1 have identified a low heat rejection engine configuration with the potential to meet the Heavy Duty Transport Technology program specific fuel consumption goal of 152 g/kW-hr. The proposed engine configuration incorporates low heat rejection, in-cylinder components designed for operation at 24 MPa peak cylinder pressure. Water cooling is eliminated by selective oil cooling of the components. A high temperature lubricant will be required due to increased in-cylinder operating temperatures. A two-stage turbocharger air system with intercooling and aftercooling was selected to meet engine boost and BMEP requirements. A turbocompound turbine stage is incorporated for exhaust energy recovery. The concept engine cost was estimated to be 43 percent higher compared to a Caterpillar 3176 engine. The higher initial engine cost is predicted to be offset by reduced operating costs due the lower fuel consumption.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keyser, Matthew A

Present-day thermal management systems for battery electric vehicles are inadequate in limiting the maximum temperature rise of the battery during extreme fast charging. If the battery thermal management system is not designed correctly, the temperature of the cells could reach abuse temperatures and potentially send the cells into thermal runaway. Furthermore, the cell and battery interconnect design needs to be improved to meet the lifetime expectations of the consumer. Each of these aspects is explored and addressed as well as outlining where the heat is generated in a cell, the efficiencies of power and energy cells, and what type ofmore » battery thermal management solutions are available in today's market. Thermal management is not a limiting condition with regard to extreme fast charging, but many factors need to be addressed especially for future high specific energy density cells to meet U.S. Department of Energy cost and volume goals.« less

Enabling fast charging - Battery thermal considerations

NASA Astrophysics Data System (ADS)

Keyser, Matthew; Pesaran, Ahmad; Li, Qibo; Santhanagopalan, Shriram; Smith, Kandler; Wood, Eric; Ahmed, Shabbir; Bloom, Ira; Dufek, Eric; Shirk, Matthew; Meintz, Andrew; Kreuzer, Cory; Michelbacher, Christopher; Burnham, Andrew; Stephens, Thomas; Francfort, James; Carlson, Barney; Zhang, Jiucai; Vijayagopal, Ram; Hardy, Keith; Dias, Fernando; Mohanpurkar, Manish; Scoffield, Don; Jansen, Andrew N.; Tanim, Tanvir; Markel, Anthony

2017-11-01

Battery thermal barriers are reviewed with regards to extreme fast charging. Present-day thermal management systems for battery electric vehicles are inadequate in limiting the maximum temperature rise of the battery during extreme fast charging. If the battery thermal management system is not designed correctly, the temperature of the cells could reach abuse temperatures and potentially send the cells into thermal runaway. Furthermore, the cell and battery interconnect design needs to be improved to meet the lifetime expectations of the consumer. Each of these aspects is explored and addressed as well as outlining where the heat is generated in a cell, the efficiencies of power and energy cells, and what type of battery thermal management solutions are available in today's market. Thermal management is not a limiting condition with regard to extreme fast charging, but many factors need to be addressed especially for future high specific energy density cells to meet U.S. Department of Energy cost and volume goals.

Development of advanced high temperature in-cylinder components and tribological systems for low heat rejection diesel engines, phase 1

NASA Technical Reports Server (NTRS)

Kroeger, C. A.; Larson, H. J.

1992-01-01

Analysis and concept design work completed in Phase 1 have identified a low heat rejection engine configuration with the potential to meet the Heavy Duty Transport Technology program specific fuel consumption goal of 152 g/kW-hr. The proposed engine configuration incorporates low heat rejection, in-cylinder components designed for operation at 24 MPa peak cylinder pressure. Water cooling is eliminated by selective oil cooling of the components. A high temperature lubricant will be required due to increased in-cylinder operating temperatures. A two-stage turbocharger air system with intercooling and aftercooling was selected to meet engine boost and BMEP requirements. A turbocompound turbine stage is incorporated for exhaust energy recovery. The concept engine cost was estimated to be 43 percent higher compared to a Caterpillar 3176 engine. The higher initial engine cost is predicted to be offset by reduced operating costs due the lower fuel consumption.

Spaceflight Human System Standards

NASA Technical Reports Server (NTRS)

Holubec, Keith; Tillman, Barry; Connolly, Jan

2009-01-01

NASA created a new approach for human system integration and human performance standards. NASA created two documents a standard and a reference handbook. The standard is titled NASA Space Flight Human-System Standard (SFHSS) and consists of two-volumes: Volume 1- Crew Health This volume covers standards needed to support astronaut health (medical care, nutrition, sleep, exercise, etc.) Volume 2 Human Factors, Habitability and Environmental Health This volume covers the standards for system design that will maintain astronaut performance (ie., environmental factors, design of facilities, layout of workstations, and lighting requirements). It includes classic human factors requirements. The new standards document is written in terms so that it is applicable to a broad range of present and future NASA systems. The document states that all new programs prepare system-specific requirements that will meet the general standards. For example, the new standard does not specify a design should accommodate specific percentiles of a defined population. Rather, NASA-STD-3001, Volume 2 states that all programs shall prepare program-specific requirements that define the user population and their size ranges. The design shall then accommodate the full size range of those users. The companion reference handbook, Human Integration Design Handbook (HIDH), was developed to capture the design consideration information from NASA-STD-3000, and adds spaceflight lessons learned, gaps in knowledge, example solutions, and suggests research to further mature specific disciplines. The HIDH serves two major purposes: HIDH is the reference document for writing human factors requirements for specific systems. HIDH contains design guidance information that helps insure that designers create systems which safely and effectively accommodate the capabilities and limitations of space flight crews.

Internships for Future Faculty: Meeting the Career Goals of the Next Generation of Educators in Marriage and Family Therapy

ERIC Educational Resources Information Center

Miller, John K.; Todahl, Jeff; Platt, Jason J.; Lambert-Shute, Jennifer; Eppler, Christie S.

2010-01-01

A key component of a doctoral education in marriage and family therapy (MFT) is the completion of an internship. Virtually all MFT doctoral internships are focused on advanced clinical practice and often are located in agencies unconnected with an academic setting. This article describes an MFT doctoral internship specifically designed to foster…

Stress Reduction at the Work-Family Interface: Positive Parenting and Self-Efficacy as Mechanisms of Change in Workplace Triple P

ERIC Educational Resources Information Center

Hartung, Doreen; Hahlweg, Kurt

2011-01-01

Workplace Triple P (WPTP) is a group-based parenting skills training specifically designed to meet the needs of employed parents. Several randomized controlled trials have demonstrated the training's efficacy. This study examined possible mechanisms of change that account for the stress reduction effects of this parenting skills training at the…

The Anger Management Project: A Group Intervention for Anger in People with Physical and Multiple Disabilities

ERIC Educational Resources Information Center

Hagiliassis, Nick; Gulbenkoglu, Hrepsime; Di Marco, Mark; Young, Suzanne; Hudson, Alan

2005-01-01

Background: This paper describes the evaluation of a group program designed specifically to meet the anger management needs of a group of individuals with various levels of intellectual disability and/or complex communication needs. Method: Twenty-nine individuals were randomly assigned to an intervention group or a waiting-list comparison group.…

Positively Fire Safe. Third Grade. Fire Safety for Texans: Fire and Burn Prevention Curriculum Guide.

ERIC Educational Resources Information Center

Texas State Commission on Fire Protection, Austin.

This booklet comprises the third grade component of a series of curriculum guides on fire and burn prevention. Designed to meet the age-specific needs of third grade students, its objectives include: (1) acquiring basic knowledge of hazards and safe storage of flammable liquids; and (2) developing positive actions to prevent fires and burns or to…

Fire Safety's My Job. Eighth Grade. Fire Safety for Texans: Fire and Burn Prevention Curriculum Guide.

ERIC Educational Resources Information Center

Texas State Commission on Fire Protection, Austin.

This booklet comprises the eighth grade component of a series of curriculum guides on fire and burn prevention. Designed to meet the age-specific needs of eighth grade students, its objectives include: (1) focusing on technical aspects of fire hazards and detection, and (2) exploring fire hazards outside the home. Texas essential elements of…

Developing the Learning Physical Science Curriculum: Adapting a Small Enrollment, Laboratory and Discussion Based Physical Science Course for Large Enrollments

ERIC Educational Resources Information Center

Goldberg, Fred; Price, Edward; Robinson, Stephen; Boyd-Harlow, Danielle; McKean, Michael

2012-01-01

We report on the adaptation of the small enrollment, lab and discussion based physical science course, "Physical Science and Everyday Thinking" (PSET), for a large-enrollment, lecture-style setting. Like PSET, the new "Learning Physical Science" (LEPS) curriculum was designed around specific principles based on research on learning to meet the…

The Devil May Be in the Details: How the Characteristics of SCHIP Programs Affect Take-Up

ERIC Educational Resources Information Center

Wolfe, Barbara; Scrivner, Scott

2005-01-01

In this paper, we explore whether the specific design of a state's program has contributed to its success in meeting two objectives of the Children's Health Insurance Program (SCHIP): increasing the health insurance coverage of children in lower-income families and doing so with a minimum reduction in their private health insurance coverage…

Fire Safety for Consumers. Economics (High School). Fire Safety for Texans: Fire and Burn Prevention Curriculum Guide.

ERIC Educational Resources Information Center

Texas State Commission on Fire Protection, Austin.

This booklet comprises the high school economics component of a series of curriculum guides on fire and burn prevention. It is designed to meet the age-specific needs of eleventh and twelfth grade students. Objectives include: (1) developing an awareness of adult responsibilities to preserve family, property, and economy; (2) preparing for…

Business Law for Business Education Departments in Pennsylvania's Public Schools. Bulletin 280.

ERIC Educational Resources Information Center

Nichols, Natalie P.

This guide is designed to aid high school teachers of business law in Pennsylvania to structure their courses. Specifically, it is intended to help teachers identify and place correct emphasis upon those areas of business law which will most nearly meet the students' needs when they reach adulthood, to help teachers to inculcate in the students…

Fire Safety Power. Sixth Grade. Fire Safety for Texans: Fire and Burn Prevention Curriculum Guide.

ERIC Educational Resources Information Center

Texas State Commission on Fire Protection, Austin.

This booklet comprises the sixth grade component of a series of curriculum guides on fire and burn prevention. Designed to meet the age-specific needs of sixth grade students, its objectives include: (1) developing a comprehensive understanding of fire physics, (2) evaluating electrical hazards and how to respond to those hazards, and (3)…

Fire Safety: Any Time, Any Place. First Grade. Fire Safety for Texans: Fire and Burn Prevention Curriculum Guide.

ERIC Educational Resources Information Center

Texas State Commission on Fire Protection, Austin.

This booklet comprises the first grade component of a series of curriculum guides on fire and burn prevention. Designed to meet the age-specific needs of first grade students, its objectives include acquiring basic knowledge of fire and burn hazards, developing a basic understanding of simple injury reduction, and encouraging parent involvement.…

Responsible for Fire Safety. Seventh Grade. Fire Safety for Texans: Fire and Burn Prevention Curriculum Guide.

ERIC Educational Resources Information Center

Texas State Commission on Fire Protection, Austin.

This booklet comprises the seventh grade component of a series of curriculum guides on fire and burn prevention. Designed to meet the age-specific needs of seventh grade students, its objectives include: (1) practicing responsible decision-making regarding fire and burn hazards, including peer pressure related to fire risks; and (2) practicing…

75 FR 7282 - Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-18

... March 19, 2010, the committee will discuss, make recommendations and vote on a PMA for the REVO MRI Pacemaker System sponsored by Medtronic. The REVO MRI Pacing System is a pacemaker (with a standard pacing indication) that has been specifically designed to be safe for the MRI environment under certain MR scanning...

Designing Collaboration Tools to Optimize Distributed Battlespace Synchronization

DTIC Science & Technology

2009-08-01

Collective Efficacy Self-efficacy represents the belief that one possesses the ability to meet the demands of a specific situation ( Bandura , 1997). These...military teams ( Alberts & Hayes, 2003). Research has shown that high- performing teams tend to optimize information exchange (Aubert & Kelsey, 2003...17    REFERENCES Alberts , D.S., & Hayes, R.E. (2003). Power to the edge: Command control in the

[Medical nutrition in Alzheimer's: the trials].

PubMed

Scheltens, Philip; Twisk, Jos W R

2013-01-01

We describe the small but statistically significant effects of the medical nutrition diet 'Souvenaid' on memory in early Alzheimer's disease in two published randomised clinical trials. We specifically discuss the design and statistical approach, which were predefined and meet current standards in the field. Further research is needed to substantiate the long term effects and learn more about the mode of action of Souvenaid.

Promoting Diversity in the Field of Evaluation: Reflections on the First Year of the Robert Wood Johnson Foundation Evaluation Fellowship Program

ERIC Educational Resources Information Center

Christie, Christina A.; Vo, Anne T.

2011-01-01

In this paper we describe an evaluation training program sponsored by the Robert Wood Johnson Foundation and led by Duquesne University and OMG Center for Collaborative Learning designed to meet the challenge of developing a cadre of diverse evaluation professionals, specifically those from traditionally underrepresented or underserved…

A Multiple-Track Nursing Sequence: Supplement to Research Report No. 1.

ERIC Educational Resources Information Center

Gilpatrick, Eleanor

Following a survey of 2,361 practical nurses in New York City municipal hospitals in 1968, a specific multiple-track nursing sequence was developed to meet manpower shortages and upgrade licensed practical nurses (LPN's) to registered nurses (RN's) and nurse's aides (NA's) to LPN's. The two models designed were for use in New York City but it is…

Optical design of free-form bicycle lamp

NASA Astrophysics Data System (ADS)

Tian, Chao; Cen, Zaofeng; Deng, Shitao; Wang, Jing

2008-03-01

Bicycle lamp used for road lighting is becoming popular now. However, few people have realized its potential market and correlative researches are far from enough. Generally speaking, researches on bicycle lamps are mostly focused on how to design a reflector which will collect light energy more efficiently and can transfer it to certain areas forward when the light source is determinated. In traditional angle of view, the reflector is usually a paraboloid or ellipsoid. However, both of them can not meet the requirement in practice most of the cases. Therefore, free form reflectors (FFRs) instead are widely used. In this paper, a new approach to design FFR which is convenient and rapid is presented. To do computer-aided simulation, certain light source should be selected first. Usually, light sources that behavior like a Lambertian emitter are modeled. To examine the correctness of this approach, a bicycle lamp is designed according to this approach to see if it can meet the requirements of the Germany standard which will be introduced in the text later. The standard requires specific illuminance values for particular points at the test screen with a distance of 10m from the source. The simulation results is exciting and can meet all the requirement. For example, 10lx is expected at the point (0, 0) while the obtained value is 10.42lx, under the conditions that the total luminous flux of the light source is 42lm and the reflectivity of FFR is 0.8. This method has certain universal significance and can provide references for the design of other illumination systems.

Multi-surface topography targeted plateau honing for the processing of cylinder liner surfaces of automotive engines

NASA Astrophysics Data System (ADS)

Lawrence, K. Deepak; Ramamoorthy, B.

2016-03-01

Cylinder bores of automotive engines are 'engineered' surfaces that are processed using multi-stage honing process to generate multiple layers of micro geometry for meeting the different functional requirements of the piston assembly system. The final processed surfaces should comply with several surface topographic specifications that are relevant for the good tribological performance of the engine. Selection of the process parameters in three stages of honing to obtain multiple surface topographic characteristics simultaneously within the specification tolerance is an important module of the process planning and is often posed as a challenging task for the process engineers. This paper presents a strategy by combining the robust process design and gray-relational analysis to evolve the operating levels of honing process parameters in rough, finish and plateau honing stages targeting to meet multiple surface topographic specifications on the final running surface of the cylinder bores. Honing experiments were conducted in three stages namely rough, finish and plateau honing on cast iron cylinder liners by varying four honing process parameters such as rotational speed, oscillatory speed, pressure and honing time. Abbott-Firestone curve based functional parameters (Rk, Rpk, Rvk, Mr1 and Mr2) coupled with mean roughness depth (Rz, DIN/ISO) and honing angle were measured and identified as the surface quality performance targets to be achieved. The experimental results have shown that the proposed approach is effective to generate cylinder liner surface that would simultaneously meet the explicit surface topographic specifications currently practiced by the industry.

NASA-STD 3001 and the Human Integration Design Handbook (HIDH): Evolution of NASA-STD-3000

NASA Technical Reports Server (NTRS)

Pickett, Lynn; Connolly, Janis; Arch, M.; Tillman, Barry; Russo, Dane

2007-01-01

The Habitability & Environmental Factors and Space Medicine Divisions have developed the Space Flight Human System Standard (SFHSS) (NASA-STD-3001) to replace NASA-STD-3000 as a new NASA standard for all human spaceflight programs. The SFHSS is composed of 2 volumes. Volume 1, Crew Health, contains medical levels of care, permissible exposure limits, and fitness for duty criteria, and permissible outcome limits as a means of defining successful operating criteria for the human system. Volume 2, Habitability and Environmental Health, contains environmental, habitability and human factors standards. Development of the Human Integration Design Handbook (HIDH), a companion to the standard, is currently under construction and entails the update and revision of NASA-STD-3000 data. This new handbook will, in the fashion of NASA STD-3000, assist engineers and designers in appropriately applying habitability, environmental and human factors principles to spacecraft design. Organized in a chapter-module-element structure, the HIDH will provide the guidance for the development of requirements, design considerations, lessons learned, example solutions, background research, and assist in the identification of gaps and research needs in the disciplines. Subject matter experts have been and continue to be solicited to participate in the update of the chapters. The purpose is to build the HIDH with the best and latest data, and provide a broad representation from experts in industry, academia, the military and the space program. The handbook and the two standards volumes work together in a unique way to achieve the required level of human-system interface. All new NASA programs will be required to meet Volumes 1 and 2. Volume 2 presents human interface goals in broad, non-verifiable standards. Volume 2 also requires that each new development program prepare a set of program-specific human factors requirements. These program-specific human and environmental factors requirements must be verifiable and tailored to assure the new system meets the Volume 2 standards. Programs will use the HIDH to write their verifiable program-specific requirements.

Recovery Act: Advanced Direct Methanol Fuel Cell for Mobile Computing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fletcher, James H.; Cox, Philip; Harrington, William J

2013-09-03

ABSTRACT Project Title: Recovery Act: Advanced Direct Methanol Fuel Cell for Mobile Computing PROJECT OBJECTIVE The objective of the project was to advance portable fuel cell system technology towards the commercial targets of power density, energy density and lifetime. These targets were laid out in the DOE’s R&D roadmap to develop an advanced direct methanol fuel cell power supply that meets commercial entry requirements. Such a power supply will enable mobile computers to operate non-stop, unplugged from the wall power outlet, by using the high energy density of methanol fuel contained in a replaceable fuel cartridge. Specifically this project focusedmore » on balance-of-plant component integration and miniaturization, as well as extensive component, subassembly and integrated system durability and validation testing. This design has resulted in a pre-production power supply design and a prototype that meet the rigorous demands of consumer electronic applications. PROJECT TASKS The proposed work plan was designed to meet the project objectives, which corresponded directly with the objectives outlined in the Funding Opportunity Announcement: To engineer the fuel cell balance-of-plant and packaging to meet the needs of consumer electronic systems, specifically at power levels required for mobile computing. UNF used existing balance-of-plant component technologies developed under its current US Army CERDEC project, as well as a previous DOE project completed by PolyFuel, to further refine them to both miniaturize and integrate their functionality to increase the system power density and energy density. Benefits of UNF’s novel passive water recycling MEA (membrane electrode assembly) and the simplified system architecture it enabled formed the foundation of the design approach. The package design was hardened to address orientation independence, shock, vibration, and environmental requirements. Fuel cartridge and fuel subsystems were improved to ensure effective fuel containment. PROJECT OVERVIEW The University of North Florida (UNF), with project partner the University of Florida, recently completed the Department of Energy (DOE) project entitled “Advanced Direct Methanol Fuel Cell for Mobile Computing”. The primary objective of the project was to advance portable fuel cell system technology towards the commercial targets as laid out in the DOE R&D roadmap by developing a 20-watt, direct methanol fuel cell (DMFC), portable power supply based on the UNF innovative “passive water recovery” MEA. Extensive component, sub-system, and system development and testing was undertaken to meet the rigorous demands of the consumer electronic application. Numerous brassboard (nonpackaged) systems were developed to optimize the integration process and facilitating control algorithm development. The culmination of the development effort was a fully-integrated, DMFC, power supply (referred to as DP4). The project goals were 40 W/kg for specific power, 55 W/l for power density, and 575 Whr/l for energy density. It should be noted that the specific power and power density were for the power section only, and did not include the hybrid battery. The energy density is based on three, 200 ml, fuel cartridges, and also did not include the hybrid battery. The results show that the DP4 system configured without the methanol concentration sensor exceeded all performance goals, achieving 41.5 W/kg for specific power, 55.3 W/l for power density, and 623 Whr/l for energy density. During the project, the DOE revised its technical targets, and the definition of many of these targets, for the portable power application. With this revision, specific power, power density, specific energy (Whr/kg), and energy density are based on the total system, including fuel tank, fuel, and hybridization battery. Fuel capacity is not defined, but the same value is required for all calculations. Test data showed that the DP4 exceeded all 2011 Technical Status values; for example, the DP4 energy density was 373 Whr/l versus the DOE 2011 status of 200 Whr/l. For the DOE 2013 Technical Goals, the operation time was increased from 10 hours to 14.3 hours. Under these conditions, the DP4 closely approached or surpassed the technical targets; for example, the DP4 achieved 468 Whr/l versus the goal of 500 Whr/l. Thus, UNF has successfully met the project goals. A fully-operational, 20-watt DMFC power supply was developed based on the UNF passive water recovery MEA. The power supply meets the project performance goals and advances portable power technology towards the commercialization targets set by the DOE.« less

A comparative study of the Unified System for Orbit Computation and the Flight Design System. [computer programs for mission planning tasks associated with space shuttle

NASA Technical Reports Server (NTRS)

Maag, W.

1977-01-01

The Flight Design System (FDS) and the Unified System for Orbit Computation (USOC) are compared and described in relation to mission planning for the shuttle transportation system (STS). The FDS is designed to meet the requirements of a standardized production tool and the USOC is designed for rapid generation of particular application programs. The main emphasis in USOC is put on adaptability to new types of missions. It is concluded that a software system having a USOC-like structure, adapted to the specific needs of MPAD, would be appropriate to support planning tasks in the area unique to STS missions.

Design control for clinical translation of 3D printed modular scaffolds.

PubMed

Hollister, Scott J; Flanagan, Colleen L; Zopf, David A; Morrison, Robert J; Nasser, Hassan; Patel, Janki J; Ebramzadeh, Edward; Sangiorgio, Sophia N; Wheeler, Matthew B; Green, Glenn E

2015-03-01

The primary thrust of tissue engineering is the clinical translation of scaffolds and/or biologics to reconstruct tissue defects. Despite this thrust, clinical translation of tissue engineering therapies from academic research has been minimal in the 27 year history of tissue engineering. Academic research by its nature focuses on, and rewards, initial discovery of new phenomena and technologies in the basic research model, with a view towards generality. Translation, however, by its nature must be directed at specific clinical targets, also denoted as indications, with associated regulatory requirements. These regulatory requirements, especially design control, require that the clinical indication be precisely defined a priori, unlike most academic basic tissue engineering research where the research target is typically open-ended, and furthermore requires that the tissue engineering therapy be constructed according to design inputs that ensure it treats or mitigates the clinical indication. Finally, regulatory approval dictates that the constructed system be verified, i.e., proven that it meets the design inputs, and validated, i.e., that by meeting the design inputs the therapy will address the clinical indication. Satisfying design control requires (1) a system of integrated technologies (scaffolds, materials, biologics), ideally based on a fundamental platform, as compared to focus on a single technology, (2) testing of design hypotheses to validate system performance as opposed to mechanistic hypotheses of natural phenomena, and (3) sequential testing using in vitro, in vivo, large preclinical and eventually clinical tests against competing therapies, as compared to single experiments to test new technologies or test mechanistic hypotheses. Our goal in this paper is to illustrate how design control may be implemented in academic translation of scaffold based tissue engineering therapies. Specifically, we propose to (1) demonstrate a modular platform approach founded on 3D printing for developing tissue engineering therapies and (2) illustrate the design control process for modular implementation of two scaffold based tissue engineering therapies: airway reconstruction and bone tissue engineering based spine fusion.

Design Control for Clinical Translation of 3D Printed Modular Scaffolds

PubMed Central

Hollister, Scott J.; Flanagan, Colleen L.; Zopf, David A.; Morrison, Robert J.; Nasser, Hassan; Patel, Janki J.; Ebramzadeh, Edward; Sangiorgio, Sophia N.; Wheeler, Matthew B.; Green, Glenn E.

2015-01-01

The primary thrust of tissue engineering is the clinical translation of scaffolds and/or biologics to reconstruct tissue defects. Despite this thrust, clinical translation of tissue engineering therapies from academic research has been minimal in the 27 year history of tissue engineering. Academic research by its nature focuses on, and rewards, initial discovery of new phenomena and technologies in the basic research model, with a view towards generality. Translation, however, by its nature must be directed at specific clinical targets, also denoted as indications, with associated regulatory requirements. These regulatory requirements, especially design control, require that the clinical indication be precisely defined a priori, unlike most academic basic tissue engineering research where the research target is typically open-ended, and furthermore requires that the tissue engineering therapy be constructed according to design inputs that ensure it treats or mitigates the clinical indication. Finally, regulatory approval dictates that the constructed system be verified, i.e., proven that it meets the design inputs, and validated, i.e., that by meeting the design inputs the therapy will address the clinical indication. Satisfying design control requires (1) a system of integrated technologies (scaffolds, materials, biologics), ideally based on a fundamental platform, as compared to focus on a single technology, (2) testing of design hypotheses to validate system performance as opposed to mechanistic hypotheses of natural phenomena, and (3) sequential testing using in vitro, in vivo, large preclinical and eventually clinical tests against competing therapies, as compared to single experiments to test new technologies or test mechanistic hypotheses. Our goal in this paper is to illustrate how design control may be implemented in academic translation of scaffold based tissue engineering therapies. Specifically, we propose to (1) demonstrate a modular platform approach founded on 3D printing for developing tissue engineering therapies and (2) illustrate the design control process for modular implementation of two scaffold based tissue engineering therapies: airway reconstruction and bone tissue engineering based spine fusion. PMID:25666115

Magnetic shielding and vacuum test for passive hydrogen masers

NASA Technical Reports Server (NTRS)

Gubser, D. U.; Wolf, S. A.; Jacoby, A. B.; Jones, L. D.

1982-01-01

Vibration tests on high permeability magnetic shields used in the SAO-NRL Advanced Development Model (ADM) hydrogen maser were made. Magnetic shielding factors were measured before and after vibration. Preliminary results indicate considerable (25%) degradation. Test results on the NRL designed vacuum pumping station for the ADM hydrogen maser are also discussed. This system employs sintered zirconium carbon getter pumps to pump hydrogen plus small ion pumps to pump the inert gases. In situ activation tests and pumping characteristics indicate that the system can meet design specifications.

Systems design study of the Pioneer Venus spacecraft. Volume 1. Technical analyses and tradeoffs, sections 1-4 (part 1 of 4)

NASA Technical Reports Server (NTRS)

1973-01-01

The results are reported of the Pioneer Venus studies from 2 October 1972 through 30 June 1973. Many missions were considered, involving two launch vehicles (Thor/Delta and Atlas/Centaur), and different launch opportunities and spacecraft configurations to meet varying science requirements, all at minimum cost. The sequence of events is described and the specific studies conducted are summarized. The effects of science payload on mission and spacecraft design are discussed along with the mission analyses.

Structural dynamics technology research in NASA: Perspective on future needs

NASA Technical Reports Server (NTRS)

1979-01-01

The perspective of a NASA ad hoc study group on future research needs in structural dynamics within the aerospace industry is presented. The common aspects of the design process across the industry are identified and the role of structural dynamics is established through a discussion of various design considerations having their basis in structural dynamics. The specific structural dynamics issues involved are identified and assessed as to their current technological status and trends. Projections of future requirements based on this assessment are made and areas of research to meet them are identified.

Challenges of Cold Conditioning and Static Testing the Ares Demonstration Motor (DM-2)

NASA Technical Reports Server (NTRS)

Quinn, Shyla; Davis, Larry C.

2011-01-01

The Ares first stage rocket is a "human-rated" motor capable of producing and sustaining 3.5 million pounds of thrust throughout it s two-minute burn period. A series of demonstration motors (DM) will be tested in different conditioned environments to confirm they meet all design specifications. The second demonstration motor (DM-2) was designated to be a "cold motor", this means the internal propellant mean bulk temperature (PMBT) was 40 +5\\-3 F. The motor was subjected to subfreezing temperatures for two months.

ECO fill: automated fill modification to support late-stage design changes

NASA Astrophysics Data System (ADS)

Davis, Greg; Wilson, Jeff; Yu, J. J.; Chiu, Anderson; Chuang, Yao-Jen; Yang, Ricky

2014-03-01

One of the most critical factors in achieving a positive return for a design is ensuring the design not only meets performance specifications, but also produces sufficient yield to meet the market demand. The goal of design for manufacturability (DFM) technology is to enable designers to address manufacturing requirements during the design process. While new cell-based, DP-aware, and net-aware fill technologies have emerged to provide the designer with automated fill engines that support these new fill requirements, design changes that arrive late in the tapeout process (as engineering change orders, or ECOs) can have a disproportionate effect on tapeout schedules, due to the complexity of replacing fill. If not handled effectively, the impacts on file size, run time, and timing closure can significantly extend the tapeout process. In this paper, the authors examine changes to design flow methodology, supported by new fill technology, that enable efficient, fast, and accurate adjustments to metal fill late in the design process. We present an ECO fill methodology coupled with the support of advanced fill tools that can quickly locate the portion of the design affected by the change, remove and replace only the fill in that area, while maintaining the fill hierarchy. This new fill approach effectively reduces run time, contains fill file size, minimizes timing impact, and minimizes mask costs due to ECO-driven fill changes, all of which are critical factors to ensuring time-to-market schedules are maintained.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klein, Steven Karl; Determan, John C.

Dynamic System Simulation (DSS) models of fissile solution systems have been developed and verified against a variety of historical configurations. DSS techniques have been applied specifically to subcritical accelerator-driven systems using fissile solution fuels of uranium. Initial DSS models were developed in DESIRE, a specialized simulation scripting language. In order to tailor the DSS models to specifically meet needs of system designers they were converted to a Visual Studio implementation, and one of these subsequently to National Instrument’s LabVIEW for human factors engineering and operator training. Specific operational characteristics of subcritical accelerator-driven systems have been examined using a DSS modelmore » tailored to this particular class using fissile fuel.« less

1.5 MW RF Load for ITER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ives, Robert Lawrence; Marsden, David; Collins, George

Calabazas Creek Research, Inc. developed a 1.5 MW RF load for the ITER fusion research facility currently under construction in France. This program leveraged technology developed in two previous SBIR programs that successfully developed high power RF loads for fusion research applications. This program specifically focused on modifications required by revised technical performance, materials, and assembly specification for ITER. This program implemented an innovative approach to actively distribute the RF power inside the load to avoid excessive heating or arcing associated with constructive interference. The new design implemented materials and assembly changes required to meet specifications. Critical components were builtmore » and successfully tested during the program.« less

Vision Tests For Medical Surveillance Or To Insure Job Fitness

NASA Astrophysics Data System (ADS)

Wolbarsht, M. L.; Landers, M. B.

1986-05-01

The rationale for designing screening type eye examinations to document visual capabilities for specific jobs or changes in visual function following exposure to specific ocular hazards is discussed. Possible applications to clinical situations are also discussed. Specific tests meeting requirements of definite end point quantification, ease of administration, and reproducibility are given for contrast (glare) sensitivity, distortions in macular imaging (Amsler grid), and color vision. The selection is aetailed for tne individual test combinations of various populations such as automobile uriver license applicants, visual display operators, and persons exposed to lasers, including military as well as non-military installers and repairers of optical fibers for communications.

An operational satellite scatterometer for wind vector measurements over the ocean

NASA Technical Reports Server (NTRS)

Grantham, W. L.; Bracalente, E. M.; Jones, W. L.; Schrader, J. H.; Schroeder, L. C.; Mitchell, J. L.

1975-01-01

Performance requirements and design characteristics of a microwave scatterometer wind sensor for measuring surface winds over the oceans on a global basis are described. Scatterometer specifications are developed from user requirements of wind vector measurement range and accuracy, swath width, resolution cell size and measurement grid spacing. A detailed analysis is performed for a baseline fan-beam scatterometer design, and its performance capabilities for meeting the SeaSat-A user requirements. Various modes of operation are discussed which will allow the resolution of questions concerning the effects of sea state on the scatterometer wind sensing ability and to verify design boundaries of the instrument.

Feasibility of magnetic bearings for advanced gas turbine engines

NASA Technical Reports Server (NTRS)

Hibner, David; Rosado, Lewis

1992-01-01

The application of active magnetic bearings to advanced gas turbine engines will provide a product with major improvements compared to current oil lubricated bearing designs. A rethinking of the engine rotating and static structure design is necessary and will provide the designer with significantly more freedom to meet the demanding goals of improved performance, increased durability, higher reliability, and increased thrust to weight ratio via engine weight reduction. The product specific technology necessary for this high speed, high temperature, dynamically complex application has been defined. The resulting benefits from this approach to aircraft engine rotor support and the complementary engine changes and improvements have been assessed.

Technical specification for vacuum systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khaw, J.

The vacuum systems at the Stanford Linear Accelerator Center (SLAC) are primarily of all-metal construction and operate at pressures from 10/sup -5/ to 10/sup -11/ Torr. The primary gas loads during operation result from thermal desorption and beam-induced desorption from the vacuum chamber walls. These desorption rates can be extremely high in the case of hydrocarbons and other contaminants. These specifications place a major emphasis on eliminating contamination sources. The specifications and procedures have been written to insure the cleanliness and vacuum integrity of all SLAC vacuum systems, and to assist personnel involved with SLAC vacuum systems in choosing andmore » designing components that are compatible with existing systems and meet the quality and reliability of SLAC vacuum standards. The specification includes requirements on design, procurement, fabrication, chemical cleaning, clean room practices, welding and brazing, helium leak testing, residual gas analyzer testing, bakeout, venting, and pumpdown. Also appended are specifications regarding acceptable vendors, isopropyl alcohol, bakeable valve cleaning procedure, mechanical engineering safety inspection, notes on synchrotron radiation, and specifications of numerous individual components. (LEW)« less

Modeling and Design Analysis Methodology for Tailoring of Aircraft Structures with Composites

NASA Technical Reports Server (NTRS)

Rehfield, Lawrence W.

2004-01-01

Composite materials provide design flexibility in that fiber placement and orientation can be specified and a variety of material forms and manufacturing processes are available. It is possible, therefore, to 'tailor' the structure to a high degree in order to meet specific design requirements in an optimum manner. Common industrial practices, however, have limited the choices designers make. One of the reasons for this is that there is a dearth of conceptual/preliminary design analysis tools specifically devoted to identifying structural concepts for composite airframe structures. Large scale finite element simulations are not suitable for such purposes. The present project has been devoted to creating modeling and design analysis methodology for use in the tailoring process of aircraft structures. Emphasis has been given to creating bend-twist elastic coupling in high aspect ratio wings or other lifting surfaces. The direction of our work was in concert with the overall NASA effort Twenty- First Century Aircraft Technology (TCAT). A multi-disciplinary team was assembled by Dr. Damodar Ambur to work on wing technology, which included our project.

PRISM Spectrograph Optical Design

NASA Technical Reports Server (NTRS)

Chipman, Russell A.

1995-01-01

The objective of this contract is to explore optical design concepts for the PRISM spectrograph and produce a preliminary optical design. An exciting optical configuration has been developed which will allow both wavelength bands to be imaged onto the same detector array. At present the optical design is only partially complete because PRISM will require a fairly elaborate optical system to meet its specification for throughput (area*solid angle). The most complex part of the design, the spectrograph camera, is complete, providing proof of principle that a feasible design is attainable. This camera requires 3 aspheric mirrors to fit inside the 20x60 cm cross-section package. A complete design with reduced throughput (1/9th) has been prepared. The design documents the optical configuration concept. A suitable dispersing prism material, CdTe, has been identified for the prism spectrograph, after a comparison of many materials.

Passive isolation/damping system for the Hubble space telescope reaction wheels

NASA Technical Reports Server (NTRS)

Hasha, Martin D.

1987-01-01

NASA's Hubble Space Telescope contain large, diffraction limited optics with extraordinary resolution and performance for surpassing existing observatories. The need to reduce structural borne vibration and resultant optical jitter from critical Pointing Control System components, Reaction Wheels, prompted the feasibility investigation and eventual development of a passive isolation system. Alternative design concepts considered were required to meet a host of stringent specifications and pass rigid tests to be successfully verified and integrated into the already built flight vehicle. The final design employs multiple arrays of fluid damped springs that attenuate over a wide spectrum, while confining newly introduced resonances to benign regions of vehicle dynamic response. Overall jitter improvement of roughly a factor of 2 to 3 is attained with this system. The basis, evolution, and performance of the isolation system, specifically discussing design concepts considered, optimization studies, development lessons learned, innovative features, and analytical and ground test verified results are presented.

Meeting the substance abuse treatment needs of lesbian, bisexual and transgender women: implications from research to practice

PubMed Central

Stevens, Sally

2012-01-01

Research on the incidence, etiology and substance abuse treatment needs of lesbian, bisexual and transgender (LBT) women is limited. Most research indicates higher levels of alcohol and drug abuse among these populations compared to their heterosexual counterparts, with recent research indicating that substance abuse is a particular concern for transgender individuals and an increasing problem among younger LBT individuals. Risk factors and reasons for substance abuse among sexual minority women are similar to those of heterosexual women, yet are substantially complicated by issues of family rejection and lack of social support, stigma and minority stress, as well as abuse and harassment. Historically, substance abuse prevention, early intervention, and clinical treatment programs were designed to meet the needs of the sexual majority population with relatively few programs designed to incorporate the specific needs of sexual minorities. This article reviews findings from previous studies and utilizes new data collected from community-based and residential substance abuse treatment programs to (1) examine issues relevant to LBT women and substance use, and (2) make recommendations for tailoring substance abuse treatment programs to meet the needs of these populations. PMID:24474874

Development of the IBSAL-SimMOpt Method for the Optimization of Quality in a Corn Stover Supply Chain

DOE PAGES

Chavez, Hernan; Castillo-Villar, Krystel; Webb, Erin

2017-08-01

Variability on the physical characteristics of feedstock has a relevant effect on the reactor’s reliability and operating cost. Most of the models developed to optimize biomass supply chains have failed to quantify the effect of biomass quality and preprocessing operations required to meet biomass specifications on overall cost and performance. The Integrated Biomass Supply Analysis and Logistics (IBSAL) model estimates the harvesting, collection, transportation, and storage cost while considering the stochastic behavior of the field-to-biorefinery supply chain. This paper proposes an IBSAL-SimMOpt (Simulation-based Multi-Objective Optimization) method for optimizing the biomass quality and costs associated with the efforts needed to meetmore » conversion technology specifications. The method is developed in two phases. For the first phase, a SimMOpt tool that interacts with the extended IBSAL is developed. For the second phase, the baseline IBSAL model is extended so that the cost for meeting and/or penalization for failing in meeting specifications are considered. The IBSAL-SimMOpt method is designed to optimize quality characteristics of biomass, cost related to activities intended to improve the quality of feedstock, and the penalization cost. A case study based on 1916 farms in Ontario, Canada is considered for testing the proposed method. Analysis of the results demonstrates that this method is able to find a high-quality set of non-dominated solutions.« less

Development of the IBSAL-SimMOpt Method for the Optimization of Quality in a Corn Stover Supply Chain

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chavez, Hernan; Castillo-Villar, Krystel; Webb, Erin

Variability on the physical characteristics of feedstock has a relevant effect on the reactor’s reliability and operating cost. Most of the models developed to optimize biomass supply chains have failed to quantify the effect of biomass quality and preprocessing operations required to meet biomass specifications on overall cost and performance. The Integrated Biomass Supply Analysis and Logistics (IBSAL) model estimates the harvesting, collection, transportation, and storage cost while considering the stochastic behavior of the field-to-biorefinery supply chain. This paper proposes an IBSAL-SimMOpt (Simulation-based Multi-Objective Optimization) method for optimizing the biomass quality and costs associated with the efforts needed to meetmore » conversion technology specifications. The method is developed in two phases. For the first phase, a SimMOpt tool that interacts with the extended IBSAL is developed. For the second phase, the baseline IBSAL model is extended so that the cost for meeting and/or penalization for failing in meeting specifications are considered. The IBSAL-SimMOpt method is designed to optimize quality characteristics of biomass, cost related to activities intended to improve the quality of feedstock, and the penalization cost. A case study based on 1916 farms in Ontario, Canada is considered for testing the proposed method. Analysis of the results demonstrates that this method is able to find a high-quality set of non-dominated solutions.« less

Laboratory evaluation of the Level TROLL 100 manufactured by In-Situ Inc.: results of pressure and temperature tests

USGS Publications Warehouse

Carnley, Mark V.; Fulford, Janice M.; Brooks, Myron H.

2013-01-01

The Level TROLL 100 manufactured by In-Situ Inc. was evaluated by the U.S. Geological Survey (USGS) Hydrologic Instrumentation Facility (HIF) for conformance to the manufacturer’s accuracy specifications for measuring pressure throughout the device’s operating temperature range. The Level TROLL 100 is a submersible, sealed, water-level sensing device with an operating pressure range equivalent to 0 to 30 feet of water over a temperature range of −20 to 50 degrees Celsius (°C). The device met the manufacturer’s stated accuracy specifications for pressure within its temperature-compensated operating range of 0 to 50 °C. The device’s accuracy specifications did not meet established USGS requirements for primary water-stage sensors used in the operation of streamgages, but the Level TROLL 100 may be suitable for other hydrologic data-collection applications. As a note, the Level TROLL 100 is not designed to meet USGS accuracy requirements. Manufacturer accuracy specifications were evaluated, and the procedures followed and the results obtained are described in this report. USGS accuracy requirements are routinely examined and reported when instruments are evaluated at the HIF.

Gigascale Silicon Research Center for Design and Test

DTIC Science & Technology

2000-01-07

students Kanna Shimizu and Chris Wilson participated in a meeting at Intel hosted by Mani Azimi, with Moenes, Ching-Tsun, Fred Rastgar, and Mani...Prof. David Dill Researchers: Kanna Shimizu Bus specifications are currently informal, resulting in ambiguities and inconsistencies. We’ve been...Expected Graduation: 6/1/2000 Advisor: Dill Last Name: Shimizu First Name: Kanna Work Address: Department of Computer Science, Gates Computer Science

TLOG: Training and Educating Operational Logistic Planners

DTIC Science & Technology

2008-05-22

monograph recommends specific changes to the current curriculum. Additions in operational knowledge provide the students technical knowledge and a...common frame of reference in campaign planning. The changes result in students not only technically competent to design a concept of support, but...planning process. The implementation of these changes enhance TLog’s curriculum to meet the course’s stated goal; the graduates will be the

Computer-Mediated Communication in English for Specific Purposes: A Case Study with Computer Science Students at Universiti Teknologi Malaysia

ERIC Educational Resources Information Center

Shamsudin, Sarimah; Nesi, Hilary

2006-01-01

This paper will describe an ESP approach to the design and implementation of computer-mediated communication (CMC) tasks for computer science students at Universiti Teknologi Malaysia, and discuss the effectiveness of the chat feature of Windows NetMeeting as a tool for developing specified language skills. CMC tasks were set within a programme of…

Entering Adulthood: Balancing Stress for Success. A Curriculum for Grades 9-12. Contemporary Health Series. [Teacher's Guide and] Student Workbook.

ERIC Educational Resources Information Center

Hart, Susan J.

This curriculum guide provides high school students with specific tools to develop insights, attitudes and life skills they need to meet life's challenges and covers critical health and family life topics. It is part of a series designed to provide educators with the curricular tools necessary to challenge students to take personal responsibility…

A Lifetime for Fire Safety. Health (High School). Fire Safety for Texans: Fire and Burn Prevention Curriculum Guide.

ERIC Educational Resources Information Center

Texas State Commission on Fire Protection, Austin.

This booklet comprises the high school health component of a series of curriculum guides on fire and burn prevention. It is designed to meet the age-specific needs of ninth and tenth grade students. Objectives include: (1) reviewing comprehensive fire and burn prevention techniques and emergency actions; (2) developing an awareness of fire safety…

Evaluation program for secondary spacecraft cells

NASA Technical Reports Server (NTRS)

Christy, D. E.

1972-01-01

The life cycle test of secondary spacecraft electric cells is discussed. The purpose of the tests is to insure that all cells put into the life cycle test meet the required specifications. The evaluation program gathers statistical information concerning cell performance characteristics and limitations. Weaknesses in cell design which are discovered during the tests are reported to research facilities in order to increase the service life of the cells.

Making Me Fire Safe. Second Grade. Fire Safety for Texans: Fire and Burn Prevention Curriculum Guide.

ERIC Educational Resources Information Center

Texas State Commission on Fire Protection, Austin.

This booklet comprises the second grade component of a series of curriculum guides on fire and burn prevention. Designed to meet the age-specific needs of second grade students, its objectives include acquiring basic understanding of how to prevent and put out fires and developing greater self-direction to prevent and react to fire, smoke, or burn…

Charged Up for Fire Safety. Fifth Grade. Fire Safety for Texans: Fire and Burn Prevention Curriculum Guide.

ERIC Educational Resources Information Center

Texas State Commission on Fire Protection, Austin.

This booklet comprises the fifth grade component of a series of curriculum guides on fire and burn prevention. Designed to meet the age-specific needs of fifth grade students, its objectives include: (1) exploring heating equipment safety, (2) analyzing the impact of fire on the outdoor environment and methods to reduce that impact, (3) developing…

DEVELOPMENT OF PERMANENT MECHANICAL REPAIR SLEEVE FOR PLASTIC PIPE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hitesh Patadia

2004-09-30

The report presents a comprehensive summary of the project status related to the development of a permanent mechanical repair fitting intended to be installed on damaged PE mains under blowing gas conditions. Specifically, the product definition has been developed taking into account relevant codes and standards and industry input. A conceptual design for the mechanical repair sleeve has been developed which meets the product definition.

76 FR 64123 - Advisory Committee on Reactor Safeguards (ACRS); Meeting of the ACRS Subcommittee on Future Plant...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-17

... NUCLEAR REGULATORY COMMISSION Advisory Committee on Reactor Safeguards (ACRS); Meeting of the ACRS Subcommittee on Future Plant Designs; Notice of Meeting The ACRS Subcommittee on Future Plant Designs will hold a meeting on November 2, 2011, Room T-2B1, 11545 Rockville Pike, Rockville, Maryland. The entire meeting will be open to public...

Electro-Mechanical Actuator. DC Resonant Link Controller

NASA Technical Reports Server (NTRS)

Schreiner, Kenneth E.

1996-01-01

This report summarizes the work performed on the 68 HP electro-mechanical actuator (EMA) system developed on NASA contract for the Electrical Actuation (ELA) Technology Bridging Program. The system was designed to demonstrate the capability of large, high power linear ELAs for applications such as Thrust Vector Control (TVC) on rocket engines. It consists of a motor controller, drive electronics and a linear actuator capable of up to 32,00 lbs loading at 7.4 inches/second. The drive electronics are based on the Resonant DC link concept and operate at a nominal frequency of 55 kHz. The induction motor is a specially designed high speed, low inertia motor capable of a 68 peak HP. The actuator was originally designed by MOOG Aerospace under an internal R & D program to meet Space Shuttle Main Engine (SSME) TVC requirements. The design was modified to meet this programs linear rate specification of 7.4 inches/second. The motor and driver were tested on a dynamometer at the Martin Marietta Space Systems facility. System frequency response, step response and force-velocity tests were conducted at the MOOG Aerospace facility. A complete description of the system and all test results can be found in the body of the report.

Requirement Assurance: A Verification Process

NASA Technical Reports Server (NTRS)

Alexander, Michael G.

2011-01-01

Requirement Assurance is an act of requirement verification which assures the stakeholder or customer that a product requirement has produced its "as realized product" and has been verified with conclusive evidence. Product requirement verification answers the question, "did the product meet the stated specification, performance, or design documentation?". In order to ensure the system was built correctly, the practicing system engineer must verify each product requirement using verification methods of inspection, analysis, demonstration, or test. The products of these methods are the "verification artifacts" or "closure artifacts" which are the objective evidence needed to prove the product requirements meet the verification success criteria. Institutional direction is given to the System Engineer in NPR 7123.1A NASA Systems Engineering Processes and Requirements with regards to the requirement verification process. In response, the verification methodology offered in this report meets both the institutional process and requirement verification best practices.

CAN-Care: an innovative model of practice-based learning.

PubMed

Raines, Deborah A

2006-01-01

The "Collaborative Approach to Nursing Care" (CAN-Care) Model of practice-based education is designed to meet the unique learning needs of the accelerated nursing program student. The model is based on a synergistic partnership between the academic and service settings, the vision of which is to create an innovative practice-based learning model, resulting in a positive experience for both the student and unit-based nurse. Thus, the objectives of quality outcomes for both the college and Health Care Organization are fulfilled. Specifically, the goal is the education of nurses ready to meet the challenges of caring for persons in the complex health care environment of the 21st century.

Expert Meeting Report: Cladding Attachment Over Exterior Insulation (BSC Report)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

The addition of insulation to the exterior of buildings is an effective means of increasing the thermal resistance of both wood framed walls as well as mass masonry wall assemblies. The location of the insulation to the exterior of the structure has many direct benefits including better effective R-value from reduced thermal bridging, better condensation resistance, reduced thermal stress on the structure, as well as other commonly associated improvements such as increased air tightness and improved water management (Hutcheon 1964, Lstiburek 2007). The intent of the meeting was to review the current state of industry knowledge regarding cladding attachment overmore » exterior insulation with a specific focus on: 1. Gravity load resistance, 2. Wind load resistance. The presentations explore these topics from an engineering design, laboratory testing, field monitoring, as well as practical construction perspective. By bringing various groups together (who have been conduction research or have experience in this area), a more holistic review of the design limits and current code language proposals can be completed and additional gaps identified. The results of which will help inform design standards and criteria.« less

Information Science Panel joint meeting with Imaging Science Panel

NASA Technical Reports Server (NTRS)

1982-01-01

Specific activity in information extraction science (taken to include data handling) is needed to: help identify the bounds of practical missions; identify potential data handling and analysis scenarios; identify the required enabling technology; and identify the requirements for a design data base to be used by the disciplines in determining potential parameters for future missions. It was defined that specific analysis topics were a function of the discipline involved, and therefore no attempt was made to define any specific analysis developments required. Rather, it was recognized that a number of generic data handling requirements exist whose solutions cannot be typically supported by the disciplines. The areas of concern were therefore defined as: data handling aspects of system design considerations; enabling technology for data handling, with specific attention to rectification and registration; and enabling technology for analysis. Within each of these areas, the following topics were addressed: state of the art (current status and contributing factors); critical issues; and recommendations for research and/or development.

Capabilities needed for the next generation of thermo-hydraulic codes for use in real time applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arndt, S.A.

1997-07-01

The real-time reactor simulation field is currently at a crossroads in terms of the capability to perform real-time analysis using the most sophisticated computer codes. Current generation safety analysis codes are being modified to replace simplified codes that were specifically designed to meet the competing requirement for real-time applications. The next generation of thermo-hydraulic codes will need to have included in their specifications the specific requirement for use in a real-time environment. Use of the codes in real-time applications imposes much stricter requirements on robustness, reliability and repeatability than do design and analysis applications. In addition, the need for codemore » use by a variety of users is a critical issue for real-time users, trainers and emergency planners who currently use real-time simulation, and PRA practitioners who will increasingly use real-time simulation for evaluating PRA success criteria in near real-time to validate PRA results for specific configurations and plant system unavailabilities.« less

Potential of agricultural fungicides for antifungal drug discovery.

PubMed

Jampilek, Josef

2016-01-01

While it is true that only a small fraction of fungal species are responsible for human mycoses, the increasing prevalence of fungal diseases has highlighted an urgent need to develop new antifungal drugs, especially for systemic administration. This contribution focuses on the similarities between agricultural fungicides and drugs. Inorganic, organometallic and organic compounds can be found amongst agricultural fungicides. Furthermore, fungicides are designed and developed in a similar fashion to drugs based on similar rules and guidelines, with fungicides also having to meet similar criteria of lead-likeness and/or drug-likeness. Modern approved specific-target fungicides are well-characterized entities with a proposed structure-activity relationships hypothesis and a defined mode of action. Extensive toxicological evaluation, including mammalian toxicology assays, is performed during the whole discovery and development process. Thus modern agrochemical research (design of modern agrochemicals) comes close to drug design, discovery and development. Therefore, modern specific-target fungicides represent excellent lead-like structures/models for novel drug design and development.

Onboard Inert Gas Generation System/Onboard Oxygen Gas Generation System (OBIGGS/OBOGS) Study. Part 1; Aircraft System Requirements

NASA Technical Reports Server (NTRS)

Reynolds, Thomas L.; Bailey, Delbert B.; Lewinski, Daniel F.; Roseburg, Conrad M.; Palaszewski, Bryan (Technical Monitor)

2001-01-01

The purpose of this technology assessment is to define a multiphase research study program investigating Onboard Inert Gas Generation Systems (OBIGGS) and Onboard Oxygen Generation Systems (OBOGS) that would identify current airplane systems design and certification requirements (Subtask 1); explore state-of-the-art technology (Subtask 2); develop systems specifications (Subtask 3); and develop an initial system design (Subtask 4). If feasible, consideration may be given to the development of a prototype laboratory test system that could potentially be used in commercial transport aircraft (Subtask 5). These systems should be capable of providing inert nitrogen gas for improved fire cargo compartment fire suppression and fuel tank inerting and emergency oxygen for crew and passenger use. Subtask I of this research study, presented herein, defines current production aircraft certification requirements and design objectives necessary to meet mandatory FAA certification requirements and Boeing design and performance specifications. These requirements will be utilized for baseline comparisons for subsequent OBIGGS/OBOGS application evaluations and assessments.

Aerospace technology development of three types of solid state remote power controllers for 120VDC with current ratings of five, and thirty amperes, one type having current limiting

NASA Technical Reports Server (NTRS)

Baker, D. E.

1975-01-01

The first generation of remote power controllers (RPC) developed included: a 5-ampere design (Type 1), capable of limiting maximum overload current to 15 amperes for .1 sec; and 5-ampere noncurrent (Type 2) and 30-ampere noncurrent (Type 3) limiting designs, both with selectable instant trip levels for high-current overload. Each design provides overcurrent protection through an inverse I squared T trip-out function with an automatic reset option and demonstrates step-applied fault capability with a 4000-ampere surge, fast-risetime (low-inductance) power source. They also meet MIL - STD - 461A specification for electromagnetic interference. The second generation RPCs traded off specification compliance for reduction in cost and complexity for the Type 1 and 2 designs and give comparable or improved performance in most areas. The noncurrent limiting RPC proved to be a more economical and feasible method of overload protection for certain load types.

Lessons Learned Using COTS Electronics for the International Space Station Radiation Environment

NASA Technical Reports Server (NTRS)

Blumer, John H.; Roth, A. (Technical Monitor)

2001-01-01

The mantra of 'Faster, Better, Cheaper' has to a large degree been interpreted as using Commercial Off-the-Shelf (COTS) components and/or circuit boards. One of the first space applications to actually use COTS in space along with radiation performance requirements was the Expedite the Processing of Experiments to Space Station (EXPRESS) Rack program, for the International Space Station (ISS). In order to meet the performance, cost and schedule targets, military grade Versa Module Eurocard (VME) was selected as the baseline design for the main computer, the Rack Interface Controller (RIC). VME was chosen as the computer backplane because of the large variety of military grade boards available, which were designed to meet the military environmental specifications (thermal, shock, vibration, etc.). These boards also have a paper pedigree in regards to components. Since these boards exceeded most ISS environmental requirements, it was reasoned using COTS mid-grade VME boards, as opposed to designing custom boards could save significant time and money. It was recognized up front the radiation environment of ISS, while benign compared to many space flight applications, would be the main challenge to using COTS. Thus in addition to selecting vendors on how well their boards met the usual performance and environmental specifications, the board's parts lists were reviewed on how well they would perform in the ISS radiation environment. However, issues with verifying that the available radiation test data was applicable to the actual part used, vendor part design changes and the fact most parts did not have valid test data soon complicated board and part selection in regards to radiation.

78 FR 17945 - Advisory Committee on Reactor Safeguards (ACRS); Meeting of the ACRS Subcommittee on Future Plant...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-25

... NUCLEAR REGULATORY COMMISSION Advisory Committee on Reactor Safeguards (ACRS); Meeting of the ACRS Subcommittee on Future Plant Designs; Notice of Meeting The ACRS Subcommittee on Future Plant Designs will hold a meeting on April 9, 2013, Room T-2B1, 11545 Rockville Pike, Rockville, Maryland. The entire meeting will be open to public attendance....

77 FR 74698 - Advisory Committee on Reactor Safeguards (ACRS); Meeting of the ACRS Subcommittee on Future Plant...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-17

... NUCLEAR REGULATORY COMMISSION Advisory Committee on Reactor Safeguards (ACRS); Meeting of the ACRS Subcommittee on Future Plant Designs; Notice of Meeting The ACRS Subcommittee on Future Plant Designs will hold a meeting on January 17, 2013, Room T-2B3, 11545 Rockville Pike, Rockville, Maryland. The meeting will be open to public attendance, wit...

34 CFR 200.79 - Exclusion of supplemental State and local funds from supplement, not supplant and comparability...

Code of Federal Regulations, 2010 CFR

2010-07-01

... academic achievement standards; (ii) Provides supplementary services designed to meet the special... at least 40 percent; (ii) Is designed to promote schoolwide reform and upgrade the entire educational... academic achievement standards that all students are expected to meet; (iii) Is designed to meet the...

Examining family meetings at end of life: The model of practice in a hospice inpatient unit.

PubMed

Meeker, Mary Ann; Waldrop, Deborah P; Seo, Jin Young

2015-10-01

Our purpose was to rigorously examine the nature of family meetings as conducted in an inpatient hospice care unit in order to generate an inductive theoretical model. In this two-phase project, we first interviewed eight members of the interdisciplinary care team who participated in multiple family meetings each week. Interview questions explored why and how they conducted family meetings. Using an observation template created from these interview data, we subsequently conducted ethnographic observations during family meetings. Using the methods of grounded theory, our findings were synthesized into a theoretical model depicting the structure and process of formal family meetings within this setting. The core of the family meeting was characterized by cognitive and affective elements aimed at supporting the family and facilitating quality care by clarifying the past, easing the present, and protecting the future. This inductive model was subsequently found to be highly aligned with a sense of coherence, an important influence on coping, and adaptation to the stress of a life-limiting illness. Provider communication with family members is particularly critical during advanced illness and end-of-life care. The National Consensus Project clinical practice guidelines for quality palliative care list regular family meetings among the recommended practices for excellent communication during end-of-life care, but do not provide specific guidance on how and when to provide such meetings. Our findings provide a theoretical model that can inform the design of a family meeting to address family members' needs for meaningful and contextualized information, validation of their important contributions to care, and preparation for the patient's death.

Co-design in synthetic biology: a system-level analysis of the development of an environmental sensing device.

PubMed

Ball, David A; Lux, Matthew W; Graef, Russell R; Peterson, Matthew W; Valenti, Jane D; Dileo, John; Peccoud, Jean

2010-01-01

The concept of co-design is common in engineering, where it is necessary, for example, to determine the optimal partitioning between hardware and software of the implementation of a system features. Here we propose to adapt co-design methodologies for synthetic biology. As a test case, we have designed an environmental sensing device that detects the presence of three chemicals, and returns an output only if at least two of the three chemicals are present. We show that the logical operations can be implemented in three different design domains: (1) the transcriptional domain using synthetically designed hybrid promoters, (2) the protein domain using bi-molecular fluorescence complementation, and (3) the fluorescence domain using spectral unmixing and relying on electronic processing. We discuss how these heterogeneous design strategies could be formalized to develop co-design algorithms capable of identifying optimal designs meeting user specifications.

Applying MDA to SDR for Space to Model Real-time Issues

NASA Technical Reports Server (NTRS)

Blaser, Tammy M.

2007-01-01

NASA space communications systems have the challenge of designing SDRs with highly-constrained Size, Weight and Power (SWaP) resources. A study is being conducted to assess the effectiveness of applying the MDA Platform-Independent Model (PIM) and one or more Platform-Specific Models (PSM) specifically to address NASA space domain real-time issues. This paper will summarize our experiences with applying MDA to SDR for Space to model real-time issues. Real-time issues to be examined, measured, and analyzed are: meeting waveform timing requirements and efficiently applying Real-time Operating System (RTOS) scheduling algorithms, applying safety control measures, and SWaP verification. Real-time waveform algorithms benchmarked with the worst case environment conditions under the heaviest workload will drive the SDR for Space real-time PSM design.

Handbook for Designing MMOD Protection

NASA Technical Reports Server (NTRS)

Arnold, Jim; Christiansen, Eric L.; Davis, Alan; Hyde, James; Lear, Dana; Liou, J.C.; Lyons, Frankel; Prior, Thomas; Studor, George; Ratliff, Martin;

Mechanical properties of direct core build-up materials.

PubMed

Combe, E C; Shaglouf, A M; Watts, D C; Wilson, N H

1999-05-01

This work was undertaken to measure mechanical properties of a diverse group of materials used for direct core build-ups, including a high copper amalgam, a silver cermet cement, a VLC resin composite and two composites specifically developed for this application. Compressive strength, elastic modulus, diametral tensile strength and flexural strength and modulus were measured for each material as a function of time up to 3 months, using standard specification tests designed for the materials. All the materials were found to meet the minimum specification requirements except in terms of flexural strength for the amalgam after 1 h and the silver cermet at all time intervals. There proved to be no obvious superior material in all respects for core build-ups, and the need exists for a specification to be established specifically for this application.

Load Distribution Factors for Composite Multicell Box Girder Bridges

NASA Astrophysics Data System (ADS)

Tiwari, Sanjay; Bhargava, Pradeep

2017-12-01

Cellular steel section composite with a concrete deck is one of the most suitable superstructures in resisting torsional and warping effects induced by highway loading. This type of structure has inherently created new design problems for engineers in estimating its load distribution when subjected to moving vehicles. Indian Codes of Practice does not provide any specific guidelines for the design of straight composite concrete deck-steel multi-cell bridges. To meet the practical requirements arising during the design process, a simple design method is needed for straight composite multi-cell bridges in the form of load distribution factors for moment and shear. This work presents load distribution characteristics of straight composite multi-cell box girder bridges under IRC trains of loads.

Design and experimental validation of a flutter suppression controller for the active flexible wing

NASA Technical Reports Server (NTRS)

Waszak, Martin R.; Srinathkumar, S.

1992-01-01

The synthesis and experimental validation of an active flutter suppression controller for the Active Flexible Wing wind tunnel model is presented. The design is accomplished with traditional root locus and Nyquist methods using interactive computer graphics tools and extensive simulation based analysis. The design approach uses a fundamental understanding of the flutter mechanism to formulate a simple controller structure to meet stringent design specifications. Experimentally, the flutter suppression controller succeeded in simultaneous suppression of two flutter modes, significantly increasing the flutter dynamic pressure despite modeling errors in predicted flutter dynamic pressure and flutter frequency. The flutter suppression controller was also successfully operated in combination with another controller to perform flutter suppression during rapid rolling maneuvers.

Optimal Experiment Design for Thermal Characterization of Functionally Graded Materials

NASA Technical Reports Server (NTRS)

Cole, Kevin D.

2003-01-01

The purpose of the project was to investigate methods to accurately verify that designed , materials meet thermal specifications. The project involved heat transfer calculations and optimization studies, and no laboratory experiments were performed. One part of the research involved study of materials in which conduction heat transfer predominates. Results include techniques to choose among several experimental designs, and protocols for determining the optimum experimental conditions for determination of thermal properties. Metal foam materials were also studied in which both conduction and radiation heat transfer are present. Results of this work include procedures to optimize the design of experiments to accurately measure both conductive and radiative thermal properties. Detailed results in the form of three journal papers have been appended to this report.

Computer aided airship design

NASA Technical Reports Server (NTRS)

Davis, S. J.; Rosenstein, H.

1975-01-01

The Comprehensive Airship Sizing and Performance Computer Program (CASCOMP) is described which was developed and used in the design and evaluation of advanced lighter-than-air (LTA) craft. The program defines design details such as engine size and number, component weight buildups, required power, and the physical dimensions of airships which are designed to meet specified mission requirements. The program is used in a comparative parametric evaluation of six advanced lighter-than-air concepts. The results indicate that fully buoyant conventional airships have the lightest gross lift required when designed for speeds less than 100 knots and the partially buoyant concepts are superior above 100 knots. When compared on the basis of specific productivity, which is a measure of the direct operating cost, the partially buoyant lifting body/tilting prop-rotor concept is optimum.

Rotor systems research aircraft predesign study. Volume 2: Conceptual study report

NASA Technical Reports Server (NTRS)

Schmidt, S. A.; Linden, A. W.

1972-01-01

The overall feasibility of the technical requirements and concepts for a rotor system research aircraft (RSRA) was determined. The designs of two aircraft were then compared against the RSRA requirements. One of these is an all new aircraft specifically designed as an RSRA vehicle. A new main rotor, transmission, wings, and fuselage are included in this design. The second aircraft uses an existing Sikorsky S-61 main rotor, an S-61 roller gearbox, and a highly modified Sikorsky S-67 airframe. The wing for this aircraft is a new design. Both aircraft employ a fan-in-fin anti-torque/yaw control system, T58-GE-16 engines for rotor power, and TF34-GE-2 turbofans for auxiliary thrust. Each aircraft meets the basic requirements and goals of the program. The all new aircraft has inflight variable main rotor shaft tilt, a side-by-side cockpit seating arrangement, and is slightly faster in the compound mode. It is also somewhat lighter since it uses new dynamic components specifically designed for the RSRA. Preliminary development plans, including schedules and costs, were prepared for both of these aircraft.

Getting what they need when they need it. Identifying barriers to information needs of family caregivers to manage dementia-related behavioral symptoms.

PubMed

Werner, Nicole E; Stanislawski, Barbara; Marx, Katherine A; Watkins, Daphne C; Kobayashi, Marissa; Kales, Helen; Gitlin, Laura N

2017-02-22

Consumer health informatics (CHI) such as web-based applications may provide the platform for enabling the over 15 million family caregivers of patients with Alzheimer's Disease or related dementias the information they need when they need it to support behavioral symptom management. However, for CHI to be successful, it is necessary that it be designed to meet the specific information needs of family caregivers in the context in which caregiving occurs. A sociotechnical systems approach to CHI design can help to understand the contextual complexities of family caregiving and account for those complexities in the design of CHI for family caregivers. This study used a sociotechnical systems approach to identify barriers to meeting caregivers' information needs related to the management of dementia-related behavioral symptoms, and to derive design implications that overcome barriers for caregiver-focused web-based platforms. We have subsequently used these design implications to inform the development of a web-based platform, WeCareAdvisor,TM which provides caregivers with information and an algorithm by which to identify and manage behavioral symptoms for which they seek management strategies. We conducted 4 focus groups with family caregivers (N=26) in a Midwestern state. Qualitative content analysis of the data was guided by a sociotechnical systems framework. We identified nine categories of barriers that family caregivers confront in obtaining needed information about behavioral symptom management from which we extrapolated design implications for a web-based platform. Based on interactions within the sociotechnical system, three critical information needs were identified: 1) timely access to information, 2) access to information that is tailored or specific to caregiver's needs and contexts, and 3) usable information that can directly inform how caregivers' manage behaviors. The sociotechnical system framework is a useful approach for identifying information needs of family caregivers to inform design of web-based platforms that are user-centered.

75 FR 58448 - Advisory Committee on Reactor Safeguards (ACRS); Meeting of the ACRS Subcommittee On Future Plant...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-24

... NUCLEAR REGULATORY COMMISSION Advisory Committee on Reactor Safeguards (ACRS); Meeting of the ACRS Subcommittee On Future Plant Designs The ACRS Subcommittee on Future Plant Designs will hold a meeting on..., 2010, 1 p.m. Until 5 p.m. The Subcommittee will review current Design Acceptance Criteria associated...

Progress Toward Fabrication of Machined Metal Shells for the First Double-Shell Implosions at the National Ignition Facility

DOE PAGES

Cardenas, Tana; Schmidt, Derek W.; Loomis, Eric N.; ...

2018-01-25

The double-shell platform fielded at the National Ignition Facility requires developments in new machining techniques and robotic assembly stations to meet the experimental specifications. Current double-shell target designs use a dense high-Z inner shell, a foam cushion, and a low-Z outer shell. The design requires that the inner shell be gas filled using a fill tube. This tube impacts the entire machining and assembly design. Other intermediate physics designs have to be fielded to answer physics questions and advance the technology to be able to fabricate the full point design in the near future. One of these intermediate designs ismore » a mid-Z imaging design. The methods of designing, fabricating, and characterizing each of the major components of an imaging double shell are discussed with an emphasis on the fabrication of the machined outer metal shell.« less

Progress Toward Fabrication of Machined Metal Shells for the First Double-Shell Implosions at the National Ignition Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cardenas, Tana; Schmidt, Derek W.; Loomis, Eric N.

The double-shell platform fielded at the National Ignition Facility requires developments in new machining techniques and robotic assembly stations to meet the experimental specifications. Current double-shell target designs use a dense high-Z inner shell, a foam cushion, and a low-Z outer shell. The design requires that the inner shell be gas filled using a fill tube. This tube impacts the entire machining and assembly design. Other intermediate physics designs have to be fielded to answer physics questions and advance the technology to be able to fabricate the full point design in the near future. One of these intermediate designs ismore » a mid-Z imaging design. The methods of designing, fabricating, and characterizing each of the major components of an imaging double shell are discussed with an emphasis on the fabrication of the machined outer metal shell.« less

Semiannual Report to Congress on the Effectiveness of the Civil Aviation Security Program

DTIC Science & Technology

1988-11-01

secure Zround environment and for providing local law enforcement support for airline and airport security measures. Finally, the passengers, the...operating environment for these air carriers. Airport security programs are designed to meet the threat to the specific airport. Of the 402 airports...assistance during this project. Responding to urgent requests from the Government of Liberia for onsite training of its airport security forces, FAA

Using Microsoft Access XP: A How-To-Do-It Manual for Librarians. How-To-Do-It Manuals for Librarians, Number 120.

ERIC Educational Resources Information Center

Butler, E. Sonny; Napier, Timothy R.

This manual is designed to assist librarians in programming unique database applications that meet specific library needs. Chapter 1 goes over the basic functions of working with Windows, describes terms such as multitasking, and shows how to use the menu and tool bars. Chapter 2 covers the basics, defines some useful terms, and presents the steps…

Selected Factors Related to Selective Service Rejection and Rejection Rate in Delaware (1967): A Study of the Characteristics of Young Men Failing to Meet Mental Qualifications for Military Service.

ERIC Educational Resources Information Center

Price, Jay R.

This study sought information about selective service rejection in Delaware, specifically rejectee characteristics, reasons for rejection, and the high rejection rate in Delaware. The basic design was a modified case study method in which a sample of individual records were examined. Differences between this sample and national samples were tested…

Using an On-Line Test To Assess Reading Skills and Predict the Ability To Successfully Pass a Reading SOL Test.

ERIC Educational Resources Information Center

Simpson, Katherine P.

Designing a remediation program to meet students' needs involves finding out what a student knows and needs to know. An online testing program, such as eduTest, may provide the answers. This test is a versatile instrument that offers benchmark tests, grade specific tests, and strand tests in the four content areas for grades K through 8. The…

Evolution of the ATLAS PanDA workload management system for exascale computational science

NASA Astrophysics Data System (ADS)

Maeno, T.; De, K.; Klimentov, A.; Nilsson, P.; Oleynik, D.; Panitkin, S.; Petrosyan, A.; Schovancova, J.; Vaniachine, A.; Wenaus, T.; Yu, D.; Atlas Collaboration

2014-06-01

An important foundation underlying the impressive success of data processing and analysis in the ATLAS experiment [1] at the LHC [2] is the Production and Distributed Analysis (PanDA) workload management system [3]. PanDA was designed specifically for ATLAS and proved to be highly successful in meeting all the distributed computing needs of the experiment. However, the core design of PanDA is not experiment specific. The PanDA workload management system is capable of meeting the needs of other data intensive scientific applications. Alpha-Magnetic Spectrometer [4], an astro-particle experiment on the International Space Station, and the Compact Muon Solenoid [5], an LHC experiment, have successfully evaluated PanDA and are pursuing its adoption. In this paper, a description of the new program of work to develop a generic version of PanDA will be given, as well as the progress in extending PanDA's capabilities to support supercomputers and clouds and to leverage intelligent networking. PanDA has demonstrated at a very large scale the value of automated dynamic brokering of diverse workloads across distributed computing resources. The next generation of PanDA will allow other data-intensive sciences and a wider exascale community employing a variety of computing platforms to benefit from ATLAS' experience and proven tools.

Challenges of Cold Conditioning and Static Testing the Second Ares Demonstration Motor (DM-2)

NASA Technical Reports Server (NTRS)

Quinn, Shyla; Davis, Larry C.

2011-01-01

On August 31, 2010, a five-segment demonstration motor (DM) for the Ares program was successfully tested. A series of demonstration motors (DMs) will be tested in different conditioned environments to confirm they meet their design specifications. The second demonstration motor (DM-2) was the first cold motor. The motor needed to be subjected to sub-freezing temperatures for two months so that its internal propellant mean bulk temperature (PMBT) was approximately 40 F. Several challenges had to be overcome to make this a successful test. One challenge was to condition four field joints to get the O-rings approximately 32 F. This would be done by applying conditioning shrouds to externally cool each field joint after the test bay was pulled off. The purpose of this conditioning was to validate the new O-ring design and allow joint heaters to be eliminated. Another challenge was maintaining temperature requirements for components in the nozzle vectoring system. A separate heating system was used to warm these components during cold conditioning. There were 53 test objectives that required 764 channels of data to be recorded; 460 were specific to DM-2. This instrumentation had to be installed prior to conditioning, which meant the baseline process and timeline had to be modified to meet this time critical schedule.

Tools reference manual for a Requirements Specification Language (RSL), version 2.0

NASA Technical Reports Server (NTRS)

Fisher, Gene L.; Cohen, Gerald C.

1993-01-01

This report describes a general-purpose Requirements Specification Language, RSL. The purpose of RSL is to specify precisely the external structure of a mechanized system and to define requirements that the system must meet. A system can be comprised of a mixture of hardware, software, and human processing elements. RSL is a hybrid of features found in several popular requirements specification languages, such as SADT (Structured Analysis and Design Technique), PSL (Problem Statement Language), and RMF (Requirements Modeling Framework). While languages such as these have useful features for structuring a specification, they generally lack formality. To overcome the deficiencies of informal requirements languages, RSL has constructs for formal mathematical specification. These constructs are similar to those found in formal specification languages such as EHDM (Enhanced Hierarchical Development Methodology), Larch, and OBJ3.

Supporting the Creation and Publication of Reviewed and Tested Teaching Modules through the InTeGrate Project

NASA Astrophysics Data System (ADS)

Bruckner, M. Z.; Birnbaum, S. J.; Bralower, T. J.; Egger, A. E.; Fox, S.; Gosselin, D. C.; Iverson, E. A. R.; Manduca, C. A.; Mcconnell, D. A.; Steer, D. N.; Taber, J. J.

2016-12-01

InTeGrate is dedicated to providing robust curricular materials that increase Earth literacy among undergraduate students. As of August 2016, 14 modules that use an interdisciplinary approach to teach about Earth-related sustainability issues across the curriculum have been published, and 19 courses and modules are undergoing final revisions. Materials are designed for undergraduate courses and have been tested in a variety of disciplines including geoscience, engineering, humanities, ethics, and Spanish language courses. The materials were developed, tested, revised, and reviewed using a two-year, highly scaffolded process that involves meeting a series of checkpoints, and is supported by a team of experts who provide guidance and formative feedback throughout the process. A series of webinars also supported teams in the development process. Author teams comprise 3-6 faculty members from at least three different institutions. Authors work collaboratively in a templated webspace designed specifically for creating materials, and representatives from the InTeGrate leadership, assessment, and web teams support each group of authors. This support team provides guidance and feedback on content, pedagogy, and web layout as authors develop materials. Authors attend two face-to-face meetings, one at the beginning of the process and another after materials are piloted in authors' classes. These meetings serve to initially orient authors to the development process, including the rubric that will guide their work, and in making revisions following the piloting phase of the project. Authors report that the meetings also provide professional development experience wherein they learn about pedagogy from each other and team leaders. The bulk of the materials development occurs remotely, with teams meeting regularly via teleconference as they follow the project timeline. All materials undergo review against the Materials Design and Refinement Rubric to ensure they meet project goals and are of high quality before being piloted in the authors' classes. Subsequent revisions are based on the authors' pilot experiences and feedback from the assessment team as well as an external review. Learn more at: serc.carleton.edu/integrate/teaching_materials/modules_courses.html

MODIS Information, Data, and Control System (MIDACS) system specifications and conceptual design

NASA Technical Reports Server (NTRS)

Han, D.; Salomonson, V.; Ormsby, J.; Ardanuy, P.; Mckay, A.; Hoyt, D.; Jaffin, S.; Vallette, B.; Sharts, B.; Folta, D.

1988-01-01

The MODIS Information, Data, and Control System (MIDACS) Specifications and Conceptual Design Document discusses system level requirements, the overall operating environment in which requirements must be met, and a breakdown of MIDACS into component subsystems, which include the Instrument Support Terminal, the Instrument Control Center, the Team Member Computing Facility, the Central Data Handling Facility, and the Data Archive and Distribution System. The specifications include sizing estimates for the processing and storage capacities of each data system element, as well as traffic analyses of data flows between the elements internally, and also externally across the data system interfaces. The specifications for the data system, as well as for the individual planning and scheduling, control and monitoring, data acquisition and processing, calibration and validation, and data archive and distribution components, do not yet fully specify the data system in the complete manner needed to achieve the scientific objectives of the MODIS instruments and science teams. The teams have not yet been formed; however, it was possible to develop the specifications and conceptual design based on the present concept of EosDIS, the Level-1 and Level-2 Functional Requirements Documents, the Operations Concept, and through interviews and meetings with key members of the scientific community.

76 FR 5220 - Advisory Committee on Reactor Safeguards (ACRS); Meeting of the ACRS Subcommittee on Future Plant...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-28

... NUCLEAR REGULATORY COMMISSION Advisory Committee on Reactor Safeguards (ACRS); Meeting of the ACRS Subcommittee on Future Plant Designs The ACRS Subcommittee on Future Plant Designs will hold a meeting on February 9, 2011, at 11545 Rockville Pike, Room T-2B1, Rockville, Maryland. The entire meeting will be open...

76 FR 16016 - Advisory Committee on Reactor Safeguards (ACRS); Meeting of the ACRS Subcommittee on Future Plant...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-22

... NUCLEAR REGULATORY COMMISSION Advisory Committee on Reactor Safeguards (ACRS); Meeting of the ACRS Subcommittee on Future Plant Designs The ACRS Subcommittee on Future Plant Designs will hold a meeting on April 5, 2011, at 11545 Rockville Pike, Room T-2B1, Rockville, Maryland. The entire meeting will be open...

76 FR 27003 - Notice of Meeting of the Agricultural Air Quality Task Force

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-10

... Task Force (AAQTF) will meet to continue discussions on critical air quality issues in relation to... between agricultural production and air quality. The meeting is open to the public, and a draft agenda is... Designations F. Next Meeting, time/place Public Input (Time will be reserved at designated times to receive...

Xyce parallel electronic simulator : users' guide.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mei, Ting; Rankin, Eric Lamont; Thornquist, Heidi K.

2011-05-01

This manual describes the use of the Xyce Parallel Electronic Simulator. Xyce has been designed as a SPICE-compatible, high-performance analog circuit simulator, and has been written to support the simulation needs of the Sandia National Laboratories electrical designers. This development has focused on improving capability over the current state-of-the-art in the following areas: (1) Capability to solve extremely large circuit problems by supporting large-scale parallel computing platforms (up to thousands of processors). Note that this includes support for most popular parallel and serial computers; (2) Improved performance for all numerical kernels (e.g., time integrator, nonlinear and linear solvers) through state-of-the-artmore » algorithms and novel techniques. (3) Device models which are specifically tailored to meet Sandia's needs, including some radiation-aware devices (for Sandia users only); and (4) Object-oriented code design and implementation using modern coding practices that ensure that the Xyce Parallel Electronic Simulator will be maintainable and extensible far into the future. Xyce is a parallel code in the most general sense of the phrase - a message passing parallel implementation - which allows it to run efficiently on the widest possible number of computing platforms. These include serial, shared-memory and distributed-memory parallel as well as heterogeneous platforms. Careful attention has been paid to the specific nature of circuit-simulation problems to ensure that optimal parallel efficiency is achieved as the number of processors grows. The development of Xyce provides a platform for computational research and development aimed specifically at the needs of the Laboratory. With Xyce, Sandia has an 'in-house' capability with which both new electrical (e.g., device model development) and algorithmic (e.g., faster time-integration methods, parallel solver algorithms) research and development can be performed. As a result, Xyce is a unique electrical simulation capability, designed to meet the unique needs of the laboratory.« less

Validation Methods Research for Fault-Tolerant Avionics and Control Systems: Working Group Meeting, 2

NASA Technical Reports Server (NTRS)

Gault, J. W. (Editor); Trivedi, K. S. (Editor); Clary, J. B. (Editor)

1980-01-01

The validation process comprises the activities required to insure the agreement of system realization with system specification. A preliminary validation methodology for fault tolerant systems documented. A general framework for a validation methodology is presented along with a set of specific tasks intended for the validation of two specimen system, SIFT and FTMP. Two major areas of research are identified. First, are those activities required to support the ongoing development of the validation process itself, and second, are those activities required to support the design, development, and understanding of fault tolerant systems.

Patient Satisfaction Measurement in Occupational and Environmental Medicine Practice.

PubMed

Drury, David L; Adamo, Philip; Cloeren, Marianne; Hegmann, Kurt T; Martin, Douglas W; Levine, Michael J; Olson, Shawn M; Pransky, Glenn S; Tacci, James A; Thiese, Matthew

2018-05-01

: High patient satisfaction is a desirable goal in medical care. Patient satisfaction measures are increasingly used to evaluate and improve quality in all types of medical practices. However, the unique aspects of occupational and environmental medicine (OEM) practice require development of OEM-specific measures and thoughtful interpretation of results. The American College of Occupational and Environmental Medicine has developed and recommends a set of specific questions to measure patient satisfaction in OEM, designed to meet anticipated regulatory requirements, facilitate quality improvement of participating OEM practices, facilitate case-management review, and offer fair and accurate assessment of OEM physicians.

Design of Quasi-Terminator Orbits near Primitive Bodies

NASA Technical Reports Server (NTRS)

Lantoine, Gregory; Broschart, Stephen B.; Grebow, Daniel J.

2013-01-01

Quasi-terminator orbits are a class of quasi-periodic orbits around a primitive body that exist in the vicinity of the well-known terminator orbits. The inherent stability of quasi-terminator trajectories and their wide variety of viewing geometries make them a very compelling option for primitive body mapping missions. In this paper, we discuss orbit design methodologies for selection of an appropriate quasi-terminator orbit that would meet the needs of a specific mission. Convergence of these orbits in an eccentric, higher-fidelity model is also discussed with an example case at Bennu, the target of the upcoming NASA's OSIRIS-REx mission.

High performance thyratron driver with low jitter.

PubMed

Verma, Rishi; Lee, P; Springham, S V; Tan, T L; Rawat, R S

2007-08-01

We report the design and development of insulated gate bipolar junction transistor based high performance driver for operating thyratrons in grounded grid mode. With careful design, the driver meets the specification of trigger output pulse rise time less than 30 ns, jitter less than +/-1 ns, and time delay less than 160 ns. It produces a -600 V pulse of 500 ns duration (full width at half maximum) at repetition rate ranging from 1 Hz to 1.14 kHz. The developed module also facilitates heating and biasing units along with protection circuitry in one complete package.

Scanning mirror for infrared sensors

NASA Technical Reports Server (NTRS)

Anderson, R. H.; Bernstein, S. B.

1972-01-01

A high resolution, long life angle-encoded scanning mirror, built for application in an infrared attitude sensor, is described. The mirror uses a Moire' fringe type optical encoder and unique torsion bar suspension together with a magnetic drive to meet stringent operational and environmental requirements at a minimum weight and with minimum power consumption. Details of the specifications, design, and construction are presented with an analysis of the mirror suspension that allows accurate prediction of performance. The emphasis is on mechanical design considerations, and brief discussions are included on the encoder and magnetic drive to provide a complete view of the mirror system and its capabilities.

Lessons learned from selecting and testing spaceflight potentiometers

NASA Technical Reports Server (NTRS)

Iskenderian, T.

1994-01-01

A solar array drive (SAD) was designed for operation on the TOPEX/POSEIDON spacecraft that was launched in August, 1992. The experience gained in selecting, specifying, testing to failure, and redesigning its position sensor produced valuable lessons for future component selection and qualification. Issues of spaceflight heritage, cost/benefit/risk assessment, and component specification are addressed. It was found that costly schedule and budget overruns may have been avoided if the capability of the candidate sensors to meet requirements had been more critically examined prior to freezing the design. The use of engineering models and early qualification tests is also recommended.

HELIOS Third Joint Working Group Meeting

NASA Technical Reports Server (NTRS)

Ousley, Gilbert; Kutzer, Ants

1970-01-01

During the past six months since the Second Helios Joint Working Group Meeting held 27-30 April 1970 at Goddard Space Flight Center, the TDS Sub-Group supported the Helios Project Office and the other Sub-Groups in the timely disposition of action items and the dissemination of information pertinent to the development of interface documentation. Of particular importance during this time period was the Project's decision to incorporate a single-channel telemetry system design aboard the spacecraft. The TDS Sub-Group participated actively in the process that led to this decision. Still under active study with TDS participation is the pending Project Office decision regarding the incorporation of a ranging capability within the telecommunications design. The TDS Sub-Group assisted the Mission Analysis and Operations Sub-Group in establishment of a study effort concerning the Near-Earth Sequence of Events from launch to launch plus 8 hours. This study, which will provide valuable data for the spacecraft telecommunications design, will include participation by the Experiment, Launch Vehicle, Spacecraft, as well as the TDS and MA&O Sub-Groups. Also during the past 6-month period, the TDS, in conjunction with the Spacecraft Sub-Group, initiated activity to develop the Helios Spacecraft/TDS Compatibility Test Plans and Procedures. Activity concerning the foregoing interface discussions has been and will continue to be based upon the "TDS Estimated Capabilities Document for the Helios Missions" (613-1), and the "DSN/Flight Project Interface Design Handbook" (810-5). These will continue to be considered TDS controlling documents until specific Helios Project/TDS interface documentation is generated and signed off by the respective parties. In addition to the above, the DSN continued the Helios Trainee Program with seven GfW/DFVLR trainees in residence at JPL. Two trainees will complete their year's residency concurrent with the Third Helios Joint Working Group Meeting, while four new trainees are expected to arrive following the Third Helios Joint Working Group Meeting. These and other activities are reported in detail in the paragraphs that follow.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nexant, Inc., San Francisco, California

The first section (Task 1) of this report by Nexant includes a survey and screening of various acid gas removal processes in order to evaluate their capability to meet the specific design requirements for thermochemical ethanol synthesis in NREL's thermochemical ethanol design report (Phillips et al. 2007, NREL/TP-510-41168). MDEA and selexol were short-listed as the most promising acid-gas removal agents based on work described in Task 1. The second report section (Task 2) describes a detailed design of an MDEA (methyl diethanol amine) based acid gas removal system for removing CO2 and H2S from biomass-derived syngas. Only MDEA was chosenmore » for detailed study because of the available resources.« less

A mobile robot system for ground servicing operations on the space shuttle

NASA Astrophysics Data System (ADS)

Dowling, K.; Bennett, R.; Blackwell, M.; Graham, T.; Gatrall, S.; O'Toole, R.; Schempf, H.

1992-11-01

A mobile system for space shuttle servicing, the Tessellator, has been configured, designed and is currently being built and integrated. Robot tasks include chemical injection and inspection of the shuttle's thermal protection system. This paper outlines tasks, rationale, and facility requirements for the development of this system. A detailed look at the mobile system and manipulator follow with a look at mechanics, electronics, and software. Salient features of the mobile robot include omnidirectionality, high reach, high stiffness and accuracy with safety and self-reliance integral to all aspects of the design. The robot system is shown to meet task, facility, and NASA requirements in its design resulting in unprecedented specifications for a mobile-manipulation system.

A mobile robot system for ground servicing operations on the space shuttle

NASA Technical Reports Server (NTRS)

Dowling, K.; Bennett, R.; Blackwell, M.; Graham, T.; Gatrall, S.; O'Toole, R.; Schempf, H.

1992-01-01

A mobile system for space shuttle servicing, the Tessellator, has been configured, designed and is currently being built and integrated. Robot tasks include chemical injection and inspection of the shuttle's thermal protection system. This paper outlines tasks, rationale, and facility requirements for the development of this system. A detailed look at the mobile system and manipulator follow with a look at mechanics, electronics, and software. Salient features of the mobile robot include omnidirectionality, high reach, high stiffness and accuracy with safety and self-reliance integral to all aspects of the design. The robot system is shown to meet task, facility, and NASA requirements in its design resulting in unprecedented specifications for a mobile-manipulation system.

Design Optimization of Gas Generator Hybrid Propulsion Boosters

NASA Technical Reports Server (NTRS)

Weldon, Vincent; Phillips, Dwight; Fink, Larry

1990-01-01

A methodology used in support of a study for NASA/MSFC to optimize the design of gas generator hybrid propulsion booster for uprating the National Space Transportation System (NSTS) is presented. The objective was to compare alternative configurations for this booster approach, optimizing each candidate concept on different bases, in order to develop data for a trade table on which a final decision was based. The methodology is capable of processing a large number of independent and dependent variables, adjusting the overall subsystems characteristics to arrive at a best compromise integrated design to meet various specific optimization criteria subject to selected constraints. For each system considered, a detailed weight statement was generated along with preliminary cost and reliability estimates.

Enabling fast charging – Battery thermal considerations

DOE PAGES

Keyser, Matthew; Pesaran, Ahmad; Li, Qibo; ...

2017-10-23

Battery thermal barriers are reviewed with regards to extreme fast charging. Present-day thermal management systems for battery electric vehicles are inadequate in limiting the maximum temperature rise of the battery during extreme fast charging. If the battery thermal management system is not designed correctly, the temperature of the cells could reach abuse temperatures and potentially send the cells into thermal runaway. Furthermore, the cell and battery interconnect design needs to be improved to meet the lifetime expectations of the consumer. Each of these aspects is explored and addressed as well as outlining where the heat is generated in a cell,more » the efficiencies of power and energy cells, and what type of battery thermal management solutions are available in today’s market. Here, thermal management is not a limiting condition with regard to extreme fast charging, but many factors need to be addressed especially for future high specific energy density cells to meet U.S. Department of Energy cost and volume goals.« less

Recent progress in NASA Langley Research Center textile reinforced composites program

NASA Technical Reports Server (NTRS)

Dexter, H. Benson; Harris, Charles E.; Johnston, Norman J.

1992-01-01

Research was conducted to explore the benefits of textile reinforced composites for transport aircraft primary structures. The objective is to develop and demonstrate the potential of affordable textile reinforced composite materials to meet design properties and damage tolerance requirements of advanced aircraft structural concepts. Some program elements include development of textile preforms, processing science, mechanics of materials, experimental characterization of materials, and development and evaluation of textile reinforced composite structural elements and subcomponents. Textile 3-D weaving, 3-D braiding, and knitting and/or stitching are being compared with conventional laminated tape processes for improved damage tolerance. Through-the-thickness reinforcements offer significant damage tolerance improvements. However, these gains must be weighted against potential loss in in-plane properties such as strength and stiffness. Analytical trade studies are underway to establish design guidelines for the application of textile material forms to meet specific loading requirements. Fabrication and testing of large structural parts are required to establish the potential of textile reinforced composite materials.

Design of Mixed Batch Reactor and Column Studies at Oak Ridge National Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Weimin; Criddle, Craig S.

2015-11-16

We (the Stanford research team) were invited as external collaborators to contribute expertise in environmental engineering and field research at the ORNL IFRC, Oak Ridge, TN, for projects carried out at the Argonne National Laboratory and funded by US DOE. Specifically, we assisted in the design of batch and column reactors using ORNL IFRC materials to ensure the experiments were relevant to field conditions. During the funded research period, we characterized ORNL IFRC groundwater and sediments in batch microcosm and column experiments conducted at ANL, and we communicated with ANL team members through email and conference calls and face-to-face meetingsmore » at the annual ERSP PI meeting and national meetings. Microcosm test results demonstrated that U(VI) in sediments was reduced to U(IV) when amended with ethanol. The reduced products were not uraninite but unknown U(IV) complexes associated with Fe. Fe(III) in solid phase was only partially reduced. Due to budget reductions at ANL, Stanford contributions ended in 2011.« less

Enabling fast charging – Battery thermal considerations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keyser, Matthew; Pesaran, Ahmad; Li, Qibo

Battery thermal barriers are reviewed with regards to extreme fast charging. Present-day thermal management systems for battery electric vehicles are inadequate in limiting the maximum temperature rise of the battery during extreme fast charging. If the battery thermal management system is not designed correctly, the temperature of the cells could reach abuse temperatures and potentially send the cells into thermal runaway. Furthermore, the cell and battery interconnect design needs to be improved to meet the lifetime expectations of the consumer. Each of these aspects is explored and addressed as well as outlining where the heat is generated in a cell,more » the efficiencies of power and energy cells, and what type of battery thermal management solutions are available in today’s market. Here, thermal management is not a limiting condition with regard to extreme fast charging, but many factors need to be addressed especially for future high specific energy density cells to meet U.S. Department of Energy cost and volume goals.« less

Constructing experimental designs for discrete-choice experiments: report of the ISPOR Conjoint Analysis Experimental Design Good Research Practices Task Force.

PubMed

Reed Johnson, F; Lancsar, Emily; Marshall, Deborah; Kilambi, Vikram; Mühlbacher, Axel; Regier, Dean A; Bresnahan, Brian W; Kanninen, Barbara; Bridges, John F P

2013-01-01

Stated-preference methods are a class of evaluation techniques for studying the preferences of patients and other stakeholders. While these methods span a variety of techniques, conjoint-analysis methods-and particularly discrete-choice experiments (DCEs)-have become the most frequently applied approach in health care in recent years. Experimental design is an important stage in the development of such methods, but establishing a consensus on standards is hampered by lack of understanding of available techniques and software. This report builds on the previous ISPOR Conjoint Analysis Task Force Report: Conjoint Analysis Applications in Health-A Checklist: A Report of the ISPOR Good Research Practices for Conjoint Analysis Task Force. This report aims to assist researchers specifically in evaluating alternative approaches to experimental design, a difficult and important element of successful DCEs. While this report does not endorse any specific approach, it does provide a guide for choosing an approach that is appropriate for a particular study. In particular, it provides an overview of the role of experimental designs for the successful implementation of the DCE approach in health care studies, and it provides researchers with an introduction to constructing experimental designs on the basis of study objectives and the statistical model researchers have selected for the study. The report outlines the theoretical requirements for designs that identify choice-model preference parameters and summarizes and compares a number of available approaches for constructing experimental designs. The task-force leadership group met via bimonthly teleconferences and in person at ISPOR meetings in the United States and Europe. An international group of experimental-design experts was consulted during this process to discuss existing approaches for experimental design and to review the task force's draft reports. In addition, ISPOR members contributed to developing a consensus report by submitting written comments during the review process and oral comments during two forum presentations at the ISPOR 16th and 17th Annual International Meetings held in Baltimore (2011) and Washington, DC (2012). Copyright © 2013 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.