Novel approaches to estimating the turbulent kinetic energy dissipation rate from low- and moderate-resolution velocity fluctuation time series

NASA Astrophysics Data System (ADS)

Wacławczyk, Marta; Ma, Yong-Feng; Kopeć, Jacek M.; Malinowski, Szymon P.

2017-11-01

In this paper we propose two approaches to estimating the turbulent kinetic energy (TKE) dissipation rate, based on the zero-crossing method by Sreenivasan et al. (1983). The original formulation requires a fine resolution of the measured signal, down to the smallest dissipative scales. However, due to finite sampling frequency, as well as measurement errors, velocity time series obtained from airborne experiments are characterized by the presence of effective spectral cutoffs. In contrast to the original formulation the new approaches are suitable for use with signals originating from airborne experiments. The suitability of the new approaches is tested using measurement data obtained during the Physics of Stratocumulus Top (POST) airborne research campaign as well as synthetic turbulence data. They appear useful and complementary to existing methods. We show the number-of-crossings-based approaches respond differently to errors due to finite sampling and finite averaging than the classical power spectral method. Hence, their application for the case of short signals and small sampling frequencies is particularly interesting, as it can increase the robustness of turbulent kinetic energy dissipation rate retrieval.

Real time outdoor exposure testing of solar cell modules and component materials

NASA Technical Reports Server (NTRS)

Anagnostou, E.; Forestieri, A. F.

1977-01-01

Plastic samples, solar cell modules, and sub-modules were exposed at test sites in Florida, Arizona, Puerto Rico, and Cleveland, Ohio, in order to determine materials suitable for use in solar cell modules with a proposed 20-year lifetime. Various environments were encountered including subtropical, subtropical with a sea air atmosphere, desert, rain forest, normal urban, and urban-polluted. The samples were exposed for periods up to six months. Materials found not suitable were polyurethane, polyester, Kapton, Mylar, and UV-stabilized Lexan. Suitable materials were acrylic, FEP-A, and glass. The results of exposure of polyvinylidene fluoride were dependent on the specific formulation, but several types appear suitable. RTV silicone rubber (clear) appears to pick up and hold dirt both as a free film and as a potting medium for modules. The results indicate that dirt accumulation and cleanability are important factors in the selection of solar cell module covers and encapsulants.

In itinere strategic environmental assessment of an integrated provincial waste system.

PubMed

Federico, Giovanna; Rizzo, Gianfranco; Traverso, Marzia

2009-06-01

In the paper, the practical problem of analysing in an integrated way the performance of provincial waste systems is approached, in the framework of the Strategic Environmental Assessment (SEA). In particular, the in itinere phase of SEA is analysed herein. After separating out a proper group of ambits, to which the waste system is supposed to determine relevant impacts, pertinent sets of single indicators are proposed. Through the adoption of such indicators the time trend of the system is investigated, and the suitability of each indicator is critically revised. The structure of the evaluation scheme, which is essentially based on the use of ambit issues and analytical indicators, calls for the application of the method of the Dashboard of Sustainability for the integrated evaluation of the whole system. The suitability of this method is shown through the paper, together with the possibility of a comparative analysis of different scenarios of interventions. Of course, the reliability of the proposed method strongly relies on the availability of a detailed set of territorial data. The method appears to represent a useful tool for public administration in the process of optimizing the policy actions aimed at minimizing the increasing problem represented by waste production in urban areas.

Chloride mass-balance method for estimating ground water recharge in arid areas: examples from western Saudi Arabia

NASA Astrophysics Data System (ADS)

Bazuhair, Abdulghaffar S.; Wood, Warren W.

1996-11-01

The chloride mass-balance method, which integrates time and aerial distribution of ground water recharge, was applied to small alluvial aquifers in the wadi systems of the Asir and Hijaz mountains in western Saudi Arabia. This application is an extension of the method shown to be suitable for estimating recharge in regional aquifers in semi-arid areas. Because the method integrates recharge in time and space it appears to be, with certain assumptions, particularly well suited for and areas with large temporal and spatial variation in recharge. In general, recharge was found to be between 3 to 4% of precipitation — a range consistent with recharge rates found in other and and semi-arid areas of the earth.

Chloride mass-balance method for estimating ground water recharge in arid areas: Examples from western Saudi Arabia

USGS Publications Warehouse

Bazuhair, A.S.; Wood, W.W.

1996-01-01

The chloride mass-balance method, which integrates time and aerial distribution of ground water recharge, was applied to small alluvial aquifers in the wadi systems of the Asir and Hijaz mountains in western Saudi Arabia. This application is an extension of the method shown to be suitable for estimating recharge in regional aquifers in semi-arid areas. Because the method integrates recharge in time and space it appears to be, with certain assumptions, particularly well suited for and areas with large temporal and spatial variation in recharge. In general, recharge was found to be between 3 to 4% of precipitation - a range consistent with recharge rates found in other arid and semi-arid areas of the earth.

Nucleic acid hybridization with RNA immobilized on filter paper.

NASA Technical Reports Server (NTRS)

Saxinger, W. C.; Ponnamperuma, C.; Gillespie, D.

1972-01-01

RNA has been immobilized in a manner suitable for use in molecular hybridization experiments with dissolved RNA or DNA by a nonaqueous solid-phase reaction with carbonyldiimidazole and RNA 'dry coated' on cellulose or, preferably, on previously activated phosphocellulose filters. Immobilization of RNA does not appear to alter its chemical character or cause it to acquire affinity for unspecific RNA or DNA. The versatility and efficiency of this method make it potentially attractive for use in routine analytical or preparative hybridization experiments, among other applications.

Thermal conductivity of Rene 41 honeycomb panels

NASA Astrophysics Data System (ADS)

Deriugin, V.

1980-12-01

Effective thermal conductivities of Rene 41 panels suitable for advanced space transportation vehicle structures were determined analytically and experimentally for temperature ranges between 20.4K (423 F) and 1186K (1675 F). The cryogenic data were obtained using a cryostat whereas the high temperature data were measured using a heat flow meter and a comparative thermal conductivity instrument respectively. Comparisons were made between analysis and experimental data. Analytical methods appear to provide reasonable definition of the honeycomb panel effective thermal conductivities.

Thermal conductivity of Rene 41 honeycomb panels. [space transportation vehicles

NASA Technical Reports Server (NTRS)

Deriugin, V.

1980-01-01

Effective thermal conductivities of Rene 41 panels suitable for advanced space transportation vehicle structures were determined analytically and experimentally for temperature ranges between 20.4K (423 F) and 1186K (1675 F). The cryogenic data were obtained using a cryostat whereas the high temperature data were measured using a heat flow meter and a comparative thermal conductivity instrument respectively. Comparisons were made between analysis and experimental data. Analytical methods appear to provide reasonable definition of the honeycomb panel effective thermal conductivities.

Identification of suitable qPCR reference genes in leaves of Brassica oleracea under abiotic stresses.

PubMed

Brulle, Franck; Bernard, Fabien; Vandenbulcke, Franck; Cuny, Damien; Dumez, Sylvain

2014-04-01

Real-time quantitative PCR is nowadays a standard method to study gene expression variations in various samples and experimental conditions. However, to interpret results accurately, data normalization with appropriate reference genes appears to be crucial. The present study describes the identification and the validation of suitable reference genes in Brassica oleracea leaves. Expression stability of eight candidates was tested following drought and cold abiotic stresses by using three different softwares (BestKeeper, NormFinder and geNorm). Four genes (BolC.TUB6, BolC.SAND1, BolC.UBQ2 and BolC.TBP1) emerged as the most stable across the tested conditions. Further gene expression analysis of a drought- and a cold-responsive gene (BolC.DREB2A and BolC.ELIP, respectively), confirmed the stability and the reliability of the identified reference genes when used for normalization in the leaves of B. oleracea. These four genes were finally tested upon a benzene exposure and all appeared to be useful reference genes along this toxicological condition. These results provide a good starting point for future studies involving gene expression measurement on leaves of B. oleracea exposed to environmental modifications.

Salt drying: a low-cost, simple and efficient method for storing plants in the field and preserving biological repositories for DNA diversity research.

PubMed

Carrió, Elena; Rosselló, Josep A

2014-03-01

Although a variety of methods have been optimized for the collection and storage of plant specimens, most of these are not suited for field expeditions for a variety of logistic reasons. Drying specimens with silica gel in polyethylene bags is currently the standard for field-sampling methods that are suitable for subsequent DNA extraction. However, silica-gel repositories are not readily available in remote areas, and its use is not very cost-effective for the long-term storage of collections or in developing countries with limited research budgets. Salting is an ancient and traditional drying process that preserves food samples by dehydrating tissues and inhibiting water-dependent cellular metabolism. We compared salt and silica-gel drying methods with respect to dehydration rates overtime, DNA quality and polymerase chain reaction(PCR) success to assess whether dry salting can be used as an effective plant preservation method for DNA analysis. Specimens from eleven plant species covering a variety of leaf structures, leaf thicknesses and water contents were analysed. Experimental work indicated that (i) levels of dehydration in sodium chloride were usually comparable to those obtained when silica gel was used, (ii) no spoilage, fungal or bacterial growth was observed for any of the species with all drying treatments and (iii) good yields of quality genomic DNA suitable for PCR applications were obtained in the salt-drying treatments. The preservation of plant tissues in commercial table salt appears to be a satisfactory, and versatile method that may be suitable in remote areas where cryogenic resources and silica repositories are not available. © 2013 John Wiley & Sons Ltd.

Accurate, high-throughput typing of copy number variation using paralogue ratios from dispersed repeats

PubMed Central

Armour, John A. L.; Palla, Raquel; Zeeuwen, Patrick L. J. M.; den Heijer, Martin; Schalkwijk, Joost; Hollox, Edward J.

2007-01-01

Recent work has demonstrated an unexpected prevalence of copy number variation in the human genome, and has highlighted the part this variation may play in predisposition to common phenotypes. Some important genes vary in number over a high range (e.g. DEFB4, which commonly varies between two and seven copies), and have posed formidable technical challenges for accurate copy number typing, so that there are no simple, cheap, high-throughput approaches suitable for large-scale screening. We have developed a simple comparative PCR method based on dispersed repeat sequences, using a single pair of precisely designed primers to amplify products simultaneously from both test and reference loci, which are subsequently distinguished and quantified via internal sequence differences. We have validated the method for the measurement of copy number at DEFB4 by comparison of results from >800 DNA samples with copy number measurements by MAPH/REDVR, MLPA and array-CGH. The new Paralogue Ratio Test (PRT) method can require as little as 10 ng genomic DNA, appears to be comparable in accuracy to the other methods, and for the first time provides a rapid, simple and inexpensive method for copy number analysis, suitable for application to typing thousands of samples in large case-control association studies. PMID:17175532

Alcohol Content in the ‘Hyper-Reality’ MTV Show ‘Geordie Shore’

PubMed Central

Lowe, Eden; Britton, John

2018-01-01

Abstract Aim To quantify the occurrence of alcohol content, including alcohol branding, in the popular primetime television UK Reality TV show ‘Geordie Shore’ Series 11. Methods A 1-min interval coding content analysis of alcohol content in the entire DVD Series 11 of ‘Geordie Shore’ (10 episodes). Occurrence of alcohol use, implied use, other alcohol reference/paraphernalia or branding was recorded. Results All categories of alcohol were present in all episodes. ‘Any alcohol’ content occurred in 78%, ‘actual alcohol use’ in 30%, ‘inferred alcohol use’ in 72%, and all ‘other’ alcohol references occurred in 59% of all coding intervals (ACIs), respectively. Brand appearances occurred in 23% of ACIs. The most frequently observed alcohol brand was Smirnoff which appeared in 43% of all brand appearances. Episodes categorized as suitable for viewing by adolescents below the legal drinking age of 18 years comprised of 61% of all brand appearances. Conclusions Alcohol content, including branding, is highly prevalent in the UK Reality TV show ‘Geordie Shore’ Series 11. Two-thirds of all alcohol branding occurred in episodes age-rated by the British Board of Film Classification (BBFC) as suitable for viewers aged 15 years. The organizations OfCom, Advertising Standards Authority (ASA) and the Portman Group should implement more effective policies to reduce adolescent exposure to on-screen drinking. The drinks industry should consider demanding the withdrawal of their brands from the show. Short Summary Alcohol content, including branding, is highly prevalent in the MTV reality TV show ‘Geordie Shore’ Series 11. Current alcohol regulation is failing to protect young viewers from exposure to such content. PMID:29365032

Physicochemical characterization of allergens: quantity, identity, purity, aggregation and conformation.

PubMed

Koppelman, Stef J; Luykx, Dion M A M; de Jongh, Harmen H J; Veldhuizen, Willem Jan

2009-01-01

Allergens and allergoids can be characterized by means of physicochemical methods, resulting in a description of the protein on different structural levels. Several techniques are available and their suitability depends on the composition of the particular sample. Current European legislation on allergen products demands characterization of final products in particular focusing on identity, degree of modification (for allergoids) and stability of the composition. Structural parameters of allergens may be used to investigate the stability of an allergen product. The challenge is to identify and optimize techniques that allow determination of protein structure in the context of a formulated pharmaceutical product. As the majority of the products currently marketed are formulated with aluminium hydroxide or aluminium phosphate as a depot, most of the methods and techniques used for protein characterization in solution are not applicable. An additional hurdle is that allergen products are based on natural extracts, comprising a mixture of proteins, both allergens and non-allergens, sometimes in the presence of other uncharacterized components from the raw material. This paper describes which methods are suitable for the different stages of allergen product manufacturing, and how these relate to the current regulatory requirements. Some of the techniques are demonstrated using a model allergen, cod parvalbumin, and a chemically modified form thereof. We conclude that a variety of methods is available for characterization of proteins in solution, and that a limited number of techniques appear to be suitable for modified allergens (allergoids). Adaptation of existing methods, e.g. mass spectroscopy and infrared spectroscopy may be helpful to obtain protein parameters of allergens in a formulated allergen product. By choosing a combination of techniques, including those additional to physicochemical approaches, relevant parameters of allergens in formulated allergen products can be assessed in order to achieve a well-characterized pharmaceutical product.

Bayesian learning

NASA Technical Reports Server (NTRS)

Denning, Peter J.

1989-01-01

In 1983 and 1984, the Infrared Astronomical Satellite (IRAS) detected 5,425 stellar objects and measured their infrared spectra. In 1987 a program called AUTOCLASS used Bayesian inference methods to discover the classes present in these data and determine the most probable class of each object, revealing unknown phenomena in astronomy. AUTOCLASS has rekindled the old debate on the suitability of Bayesian methods, which are computationally intensive, interpret probabilities as plausibility measures rather than frequencies, and appear to depend on a subjective assessment of the probability of a hypothesis before the data were collected. Modern statistical methods have, however, recently been shown to also depend on subjective elements. These debates bring into question the whole tradition of scientific objectivity and offer scientists a new way to take responsibility for their findings and conclusions.

A dual-adaptive support-based stereo matching algorithm

NASA Astrophysics Data System (ADS)

Zhang, Yin; Zhang, Yun

2017-07-01

Many stereo matching algorithms use fixed color thresholds and a rigid cross skeleton to segment supports (viz., Cross method), which, however, does not work well for different images. To address this issue, this paper proposes a novel dual adaptive support (viz., DAS)-based stereo matching method, which uses both appearance and shape information of a local region to segment supports automatically, and, then, integrates the DAS-based cost aggregation with the absolute difference plus census transform cost, scanline optimization and disparity refinement to develop a stereo matching system. The performance of the DAS method is also evaluated in the Middlebury benchmark and by comparing with the Cross method. The results show that the average error for the DAS method 25.06% lower than that for the Cross method, indicating that the proposed method is more accurate, with fewer parameters and suitable for parallel computing.

Investigation of recrystallization of amorphous trehalose through hot-humidity stage X-ray powder diffraction.

PubMed

Jójárt-Laczkovich, Orsolya; Katona, Gábor; Aigner, Zoltán; Szabó-Révész, Piroska

2016-12-01

The aim of this work was an investigation of the physical changes of the amorphous model material spray-dried trehalose through the use of various analytical techniques and to identify a suitable, rapid method able to quantify the changes. The crystallinity changes and recrystallization process of amorphous samples were investigated by hot-humidity stage X-ray powder diffractometry (HH-XRPD) with fresh samples, conventional X-ray powder diffractometry (XRPD) used stored samples and by differential scanning calorimetry (DSC). The data from the three methods were compared and the various forms of trehalose were analysed. HH-XRPD demonstrated that the recrystallization began at 40 and 60°C up to 45% RH and at 70°C up to 30% RH into dihydrate form. At 70°C up to 60% RH the anhydrous form of trehalose appeared too. Conventional XRPD results showed, that in the 28days stored samples the dihydrate form was detected at 40°C, 50% RH. Storage at 60°C, 40% RH resulted in the appearance of the anhydrous form and at 60°C, 50% RH both polymorphic forms were detected. By carrying out the DSC measurements at different temperatures the fraction of recrystallized trehalose dihydrate was detected. The recrystallization investigated by HH-XRPD and DSC followed Avrami kinetics, the calculated rate constants of isothermal crystallization (K) were same. Both HH-XRPD and conventional XRPD was suitable for the detection of the physical changes of the amorphous model material. DSC measurements showed similar results as HH-XRPD. Primarily HH-XRPD could be suggested for prediction, because the method is fast and every changes could be studied on one sample. Copyright © 2016 Elsevier B.V. All rights reserved.

Never blame the umpire - a review of Situation Awareness models and methods for examining the performance of officials in sport.

PubMed

Neville, Timothy J; Salmon, Paul M

2016-07-01

As sport becomes more complex, there is potential for ergonomics concepts to help enhance the performance of sports officials. The concept of Situation Awareness (SA) appears pertinent given the requirement for officials to understand what is going on in order to make decisions. Although numerous models exist, none have been applied to examine officials, and only several recent examples have been applied to sport. This paper examines SA models and methods to identify if any have applicability to officials in sport (OiS). Evaluation of the models and methods identified potential applications of individual, team and systems models of SA. The paper further demonstrates that the Distributed Situation Awareness model is suitable for studying officials in fastball sports. It is concluded that the study of SA represents a key area of multidisciplinary research for both ergonomics and sports science in the context of OiS. Practitioner Summary: Despite obvious synergies, applications of cognitive ergonomics concepts in sport are sparse. This is especially so for Officials in Sport (OiS). This article presents an evaluation of Situation Awareness models and methods, providing practitioners with guidance on which are the most suitable for OiS system design and evaluation.

Growth of lead tin telluride crystals in gels

NASA Technical Reports Server (NTRS)

Barber, Patrick G.

1986-01-01

Improved gels and several geometries were investigated for use in growing crystals. The use of lead sulfide test crystals proved workable, but it was impossible to obtain and maintain a sufficiently concentrated telluride ion solution to successfully grow lead telluride crystals. It appears that oxygen in the solution is capable of oxidizing the telluride ion up to tellurium metal. The method may still be successful, but only if precautions are taken to eliminate dissolved oxygen from the gels and aqueous solutions and to maintain a suitable concentration of telluride, Te(2)-(aq.).

Robust Dynamic Multi-objective Vehicle Routing Optimization Method.

PubMed

Guo, Yi-Nan; Cheng, Jian; Luo, Sha; Gong, Dun-Wei

2017-03-21

For dynamic multi-objective vehicle routing problems, the waiting time of vehicle, the number of serving vehicles, the total distance of routes were normally considered as the optimization objectives. Except for above objectives, fuel consumption that leads to the environmental pollution and energy consumption was focused on in this paper. Considering the vehicles' load and the driving distance, corresponding carbon emission model was built and set as an optimization objective. Dynamic multi-objective vehicle routing problems with hard time windows and randomly appeared dynamic customers, subsequently, were modeled. In existing planning methods, when the new service demand came up, global vehicle routing optimization method was triggered to find the optimal routes for non-served customers, which was time-consuming. Therefore, robust dynamic multi-objective vehicle routing method with two-phase is proposed. Three highlights of the novel method are: (i) After finding optimal robust virtual routes for all customers by adopting multi-objective particle swarm optimization in the first phase, static vehicle routes for static customers are formed by removing all dynamic customers from robust virtual routes in next phase. (ii)The dynamically appeared customers append to be served according to their service time and the vehicles' statues. Global vehicle routing optimization is triggered only when no suitable locations can be found for dynamic customers. (iii)A metric measuring the algorithms' robustness is given. The statistical results indicated that the routes obtained by the proposed method have better stability and robustness, but may be sub-optimum. Moreover, time-consuming global vehicle routing optimization is avoided as dynamic customers appear.

Validation and Comparison of Two Sampling Methods to Assess Dermal Exposure to Drilling Fluids and Crude Oil

PubMed Central

Galea, Karen S.; McGonagle, Carolyn; Sleeuwenhoek, Anne; Todd, David; Jiménez, Araceli Sánchez

2014-01-01

Dermal exposure to drilling fluids and crude oil is an exposure route of concern. However, there have been no published studies describing sampling methods or reporting dermal exposure measurements. We describe a study that aimed to evaluate a wipe sampling method to assess dermal exposure to an oil-based drilling fluid and crude oil, as well as to investigate the feasibility of using an interception cotton glove sampler for exposure on the hands/wrists. A direct comparison of the wipe and interception methods was also completed using pigs’ trotters as a surrogate for human skin and a direct surface contact exposure scenario. Overall, acceptable recovery and sampling efficiencies were reported for both methods, and both methods had satisfactory storage stability at 1 and 7 days, although there appeared to be some loss over 14 days. The methods’ comparison study revealed significantly higher removal of both fluids from the metal surface with the glove samples compared with the wipe samples (on average 2.5 times higher). Both evaluated sampling methods were found to be suitable for assessing dermal exposure to oil-based drilling fluids and crude oil; however, the comparison study clearly illustrates that glove samplers may overestimate the amount of fluid transferred to the skin. Further comparison of the two dermal sampling methods using additional exposure situations such as immersion or deposition, as well as a field evaluation, is warranted to confirm their appropriateness and suitability in the working environment. PMID:24598941

Use of microcomputers for self-assessment and continuing education in anaesthesia.

PubMed Central

Schmulian, C; Kenny, G N; Campbell, D

1982-01-01

The suitability of computer-assisted self-assessment was evaluated as a means of quality assurance in anaesthesia. Altogether 202 anaesthetists participated in four trials of the method. Analyses of their performance in a self-assessment programme dealing with obstetric anaesthesia showed significant differences in the levels of knowledge of anaesthetists practising for different numbers of years. The acceptability of computer-assisted self-assessment ranged from 91% to 100% for the four trials. Similar programs have been shown to be of value in medical education and thus computer-assisted self-assessment appears to fulfil simultaneously the functions of self-assessment and continuing education. The criteria for a method of quality assurance are met. PMID:6800476

Field test comparison of two dermal tolerance assessment methods of hand hygiene products.

PubMed

Girard, R; Carré, E; Pires-Cronenberger, S; Bertin-Mandy, M; Favier-Bulit, M C; Coyault, C; Coudrais, S; Billard, M; Regard, A; Kerhoas, A; Valdeyron, M L; Cracco, B; Misslin, P

2008-06-01

This study aimed to compare the sensitivity and workload requirement of two dermal tolerance assessment methods of hand hygiene products, in order to select a suitable pilot testing method for field tests. An observer-rating method and a self-assessment method were compared in 12 voluntary hospital departments (autumn/winter of 2005-2006). Three test-periods of three weeks were separated by two-week intervals during which the routine products were reintroduced. The observer rating method scored dryness and irritation on four-point scales. In the self-assessment method, the user rated appearance, intactness, moisture content, and sensation on a visual analogue scale which was converted into a 10-point numerical scale. Eleven products (soaps) were tested (223/250 complete reports for observer rating, 131/251 for self-assessment). Two products were significantly less well tolerated than the routine product according to the observers, four products according to the self-assessments. There was no significant difference between the two methods when products were classified according to tolerance (Fisher's test: P=0.491). For the symptom common to both assessment methods (dryness), there is a good correlation between the two methods (Spearman's Rho: P=0.032). The workload was higher for observer rating method (288 h of observer time plus 122 h of prevention team and pharmacist time compared with 15 h of prevention team and pharmacist time for self-assessment). In conclusion, the self-assessment method was considered more suitable for pilot testing, although further time should be allocated for educational measures as the return rate of complete self-assessment forms was poor.

10 CFR 963.16 - Postclosure suitability evaluation method.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 4 2014-01-01 2014-01-01 false Postclosure suitability evaluation method. 963.16 Section... Determination, Methods, and Criteria § 963.16 Postclosure suitability evaluation method. (a) DOE will evaluate postclosure suitability using the total system performance assessment method. DOE will conduct a total system...

10 CFR 963.16 - Postclosure suitability evaluation method.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 4 2011-01-01 2011-01-01 false Postclosure suitability evaluation method. 963.16 Section... Determination, Methods, and Criteria § 963.16 Postclosure suitability evaluation method. (a) DOE will evaluate postclosure suitability using the total system performance assessment method. DOE will conduct a total system...

10 CFR 963.16 - Postclosure suitability evaluation method.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 4 2012-01-01 2012-01-01 false Postclosure suitability evaluation method. 963.16 Section... Determination, Methods, and Criteria § 963.16 Postclosure suitability evaluation method. (a) DOE will evaluate postclosure suitability using the total system performance assessment method. DOE will conduct a total system...

Case-oriented selection of investigation methods in direct access: A comparison between physiotherapy trainees at professional colleges and in bachelor's study courses.

PubMed

Konrad, Ralf; Geraedts, Max

2018-01-01

Objective: Direct access to physiotherapy services is currently discussed in Germany. Its introduction would mean that initial diagnoses must be made in physiotherapy practices as well. However, it was not yet investigated whether the current training in physiotherapy is sufficient for this, and whether there are differences between the training systems. This study aims to answer the question of whether trainees at the end of Bachelor's studies (BS) are more reliably able to assess the case-related suitability of examination methods than professional college students (FS). Methodology: Questionnaires were developed to assess the suitability of examination methods for diagnostic inquiries. All professional colleges and bachelor's study courses listed with the German Physiotherapy Association were asked to present the questionnaires to their final classes. Results: In 216 addressed professional colleges and 24 bachelor's study courses, the return rate was 9.26% for professional colleges and 33.33% for study courses. One hundred thirty-eight questionnaires from students in 8 study courses and 368 questionnaires from students at 20 professional colleges were evaluated. The mean of correct decisions in total (of max. 54) was 19.01 (BS) or 15.73 (FS); in structure-related and function-related examination methods (of max. 42), it was 17.22 (BS) and 14.8 (FS); in activity-related methods (of max. 12), it was 1.97 (BS) and 0.89 (FS). Out of a max. of 49 examination methods, 23.45 (BS) and 26.72 (FS) were stated as unknown. Conclusion: The university students made correct decisions on the suitability of examination methods significantly more frequently than the professional college students. However, the determined group difference is low. Overall, the results do not appear sufficient for direct access. Training would have to be adapted for this purpose.

Estimating of aquifer parameters from the single-well water-level measurements in response to advancing longwall mine by using particle swarm optimization

NASA Astrophysics Data System (ADS)

Buyuk, Ersin; Karaman, Abdullah

2017-04-01

We estimated transmissivity and storage coefficient values from the single well water-level measurements positioned ahead of the mining face by using particle swarm optimization (PSO) technique. The water-level response to the advancing mining face contains an semi-analytical function that is not suitable for conventional inversion shemes because the partial derivative is difficult to calculate . Morever, the logaritmic behaviour of the model create difficulty for obtaining an initial model that may lead to a stable convergence. The PSO appears to obtain a reliable solution that produce a reasonable fit between water-level data and model function response. Optimization methods have been used to find optimum conditions consisting either minimum or maximum of a given objective function with regard to some criteria. Unlike PSO, traditional non-linear optimization methods have been used for many hydrogeologic and geophysical engineering problems. These methods indicate some difficulties such as dependencies to initial model, evolution of the partial derivatives that is required while linearizing the model and trapping at local optimum. Recently, Particle swarm optimization (PSO) became the focus of modern global optimization method that is inspired from the social behaviour of birds of swarms, and appears to be a reliable and powerful algorithms for complex engineering applications. PSO that is not dependent on an initial model, and non-derivative stochastic process appears to be capable of searching all possible solutions in the model space either around local or global optimum points.

International travel between global urban centres vulnerable to yellow fever transmission

PubMed Central

Brent, Shannon E; Watts, Alexander; Cetron, Martin; German, Matthew; Kraemer, Moritz UG; Bogoch, Isaac I; Brady, Oliver J; Hay, Simon I; Creatore, Maria I

2018-01-01

Abstract Objective To examine the potential for international travel to spread yellow fever virus to cities around the world. Methods We obtained data on the international flight itineraries of travellers who departed yellow fever-endemic areas of the world in 2016 for cities either where yellow fever was endemic or which were suitable for viral transmission. Using a global ecological model of dengue virus transmission, we predicted the suitability of cities in non-endemic areas for yellow fever transmission. We obtained information on national entry requirements for yellow fever vaccination at travellers’ destination cities. Findings In 2016, 45.2 million international air travellers departed from yellow fever-endemic areas of the world. Of 11.7 million travellers with destinations in 472 cities where yellow fever was not endemic but which were suitable for virus transmission, 7.7 million (65.7%) were not required to provide proof of vaccination upon arrival. Brazil, China, India, Mexico, Peru and the United States of America had the highest volumes of travellers arriving from yellow fever-endemic areas and the largest populations living in cities suitable for yellow fever transmission. Conclusion Each year millions of travellers depart from yellow fever-endemic areas of the world for cities in non-endemic areas that appear suitable for viral transmission without having to provide proof of vaccination. Rapid global changes in human mobility and urbanization make it vital for countries to re-examine their vaccination policies and practices to prevent urban yellow fever epidemics. PMID:29875519

Validation and comparison of two sampling methods to assess dermal exposure to drilling fluids and crude oil.

PubMed

Galea, Karen S; McGonagle, Carolyn; Sleeuwenhoek, Anne; Todd, David; Jiménez, Araceli Sánchez

2014-06-01

Dermal exposure to drilling fluids and crude oil is an exposure route of concern. However, there have been no published studies describing sampling methods or reporting dermal exposure measurements. We describe a study that aimed to evaluate a wipe sampling method to assess dermal exposure to an oil-based drilling fluid and crude oil, as well as to investigate the feasibility of using an interception cotton glove sampler for exposure on the hands/wrists. A direct comparison of the wipe and interception methods was also completed using pigs' trotters as a surrogate for human skin and a direct surface contact exposure scenario. Overall, acceptable recovery and sampling efficiencies were reported for both methods, and both methods had satisfactory storage stability at 1 and 7 days, although there appeared to be some loss over 14 days. The methods' comparison study revealed significantly higher removal of both fluids from the metal surface with the glove samples compared with the wipe samples (on average 2.5 times higher). Both evaluated sampling methods were found to be suitable for assessing dermal exposure to oil-based drilling fluids and crude oil; however, the comparison study clearly illustrates that glove samplers may overestimate the amount of fluid transferred to the skin. Further comparison of the two dermal sampling methods using additional exposure situations such as immersion or deposition, as well as a field evaluation, is warranted to confirm their appropriateness and suitability in the working environment. © The Author 2014. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Separation system suitability (3S): a new criterion of chromatogram classification in HPLC based on cross-evaluation of separation capacity/peak symmetry and its application to complex mixtures of anthraquinones.

PubMed

Nowik, Witold; Héron, Sylvie; Bonose, Myriam; Tchapla, Alain

2013-10-07

A comparison of chromatograms obtained in a series of separation conditions for a given complex mixture may be done with a series of chromatographic descriptors. In this study, we used two descriptors: the number of critical pairs and symmetry of peaks, further rescaled and converted to the corresponding critical pairs' coefficient (CPc) and symmetry coefficient (Sc). Considering the difficulty of appreciating global separation quality using CPc and Sc criteria separately, as their respective values are usually uncorrelated, a double-criteria cross-evaluation system was required. For that purpose we tested the commonly used multi-criteria decision-making method - Derringer's desirability function (D) - as well as the recently introduced sum of ranking differences (SRD). To facilitate the graphical comparison of both approaches, the desirability function (D) was used in the inverse form (Dinv). The advantages and drawbacks of both evaluation methods, especially the respective under- or over-evaluation of outliers, caused us to introduce a new ranking approach, separation system suitability (3S). The obtained suitability rankings for the three tested approaches (Dinv, SRD and 3S) are different; nevertheless, 3S appears to be the most balanced and the easiest to interpret as well. The approach developed for selection of suitable systems was applied to the problem of separation of complex mixtures through the analysis of a series of standards of anthraquinone derivatives. To judge the pertinence of this evaluation, a sample containing a number of natural anthraquinones extracted from the bark of Indian mulberry (Morinda citrifolia) was analysed. In conclusion, the proposed methodology for the cross-evaluation of the series of chromatograms using single specific descriptors (CPc and Sc) through a global composite descriptor (3S) significantly simplifies the decision that separation systems are the most suitable for the separation of complex target mixtures of compounds.

Study of immunoglobulin G thin layers obtained by the Langmuir-Blodgett method: application to immunosensors.

PubMed

Barraud, A; Perrot, H; Billard, V; Martelet, C; Therasse, J

1993-01-01

Nowadays, immunosensors play a leading part in the field of bioanalytical chemistry research. As with any biosensor, they need appropriate transducers and a suitable technique to immobilize the active biocomponents. In this study, two transduction modes were chosen: mass effects (quartz microbalance measurements) and geometric and dielectric effects (capacitance measurements). The Langmuir-Blodgett (LB) method appears to be quite suitable for generating biospecific surfaces. This work has focused on the detection of staphylococcal enterotoxin B, the corresponding antibody being immobilized at the surface of fatty acids by a variant of the LB method. The composition of the film and the nature of antibody-fatty acid interactions were studied by means of the two transducers mentioned above. FTIR (Fourier transform infra-red) spectroscopy and protein diagnostic assay. Influence of several parameters (pH, ionic strength, transfer pressure, antibody concentration in the subphase) was investigated. The immobilization rate reached its maximum when experimental conditions allowed optimal electrostatic interactions. In this case, the quartz crystal microbalance response, in air, reached 55 Hz per monolayer of immobilized immunoglobulin G and the equivalent capacitance variation, measured in liquid media, was around 300 pF cm-2. Activity of the biospecific LB films, when binding enterotoxin, was checked by the classical ELISA (enzyme immuno-linked assay) technique.

Black Model Appearance and Product Evaluations.

ERIC Educational Resources Information Center

Kerin, Roger A.

1979-01-01

Examines a study of how human models affect the impression conveyed by an advertisement, particularly the effect of a Black model's physical characteristics on product evaluations among Black and White females.Results show that the physical appearance of the model influenced impressions of product quality and suitability for personal use. (JMF)

Quality of Patient Information Websites About Congenital Heart Defects: Mixed-Methods Study of Perspectives Among Individuals With Experience of a Prenatal Diagnosis

PubMed Central

Melander Marttala, Ulla; Wadensten, Barbro; Bergman, Gunnar; Axelsson, Ove; Mattsson, Elisabet

2017-01-01

Background When a heart defect is prenatally diagnosed in the fetus, expectant parents experience a great need for information about various topics. After the diagnosis, the Web is used for supplemental information, and the scarcity of research calls attention to the need to explore patient information websites from the perspectives of the intended consumers. Objective The overarching aim of this study was to explore the quality of Swedish patient information websites about congenital heart defects, from the perspectives of individuals with experience of a prenatal diagnosis of congenital heart defect in the fetus. Methods This was a mixed-methods study of websites identified through systematic searches in the two most used Web-based search engines. Of the total 80 screened hits, 10 hits led to patient information websites about congenital heart defects. A quality assessment tool inspired by a previous study was used to evaluate each website’s appearance, details, relevance, suitability, information about treatment choices, and overall quality. Answers were given on a 5-point Likert scale, ranging from 1, representing the lowest score, to 5, representing the highest score. Each website was assessed individually by persons with experience of continued (n=4) and terminated (n=5) pregnancy following a prenatal diagnosis. Assessments were analyzed with Kendall’s coefficient of concordance W, Mann-Whitney U test, Friedman’s test, and a Wilcoxon-Nemenyi-McDonald-Thompson test. In addition, each assessor submitted written responses to open-ended questions in the quality assessment tool, and two joint focus group discussions were conducted with each group of assessors. The qualitative data were analyzed with inductive manifest content analysis. Results Assessments represented a low score (median=2.0) for treatment choices and moderate scores (median=3.0) for appearance, details, relevance, suitability, and overall quality. No website had a median of the highest achievable score for any of the questions in the quality assessment tool. Medians of the lowest achievable score were found in questions about treatment choices (n=4 websites), details (n=2 websites), suitability (n=1 website), and overall quality (n=1 website). Websites had significantly different scores for appearance (P=.01), details (P<.001), relevance (P<.001), suitability (P<.001), treatment choices (P=.04), and overall quality (P<.001). The content analysis of the qualitative data generated six categories: (1) advertisements, (2) comprehensiveness, (3) design, (4) illustrations and pictures, (5) language, and (6) trustworthiness. Various issues with the included websites were highlighted, including the use of inappropriate advertisements, biased information, poor illustrations, complex language, and poor trustworthiness. Conclusions From the perspectives of the intended consumers, patient information websites about congenital heart defects are, to a large extent, inadequate tools for supplemental information following a prenatal diagnosis. Health professionals should initiate discussions with patients about their intentions to use the Web, inform them about the varied quality in the Web-based landscape, and offer recommendations for appropriate Web-based sources. PMID:28899846

Comparison of culture-based, vital stain and PMA-qPCR methods for the quantitative detection of viable hookworm ova.

PubMed

Gyawali, P; Sidhu, J P S; Ahmed, W; Jagals, P; Toze, S

2017-06-01

Accurate quantitative measurement of viable hookworm ova from environmental samples is the key to controlling hookworm re-infections in the endemic regions. In this study, the accuracy of three quantitative detection methods [culture-based, vital stain and propidium monoazide-quantitative polymerase chain reaction (PMA-qPCR)] was evaluated by enumerating 1,000 ± 50 Ancylostoma caninum ova in the laboratory. The culture-based method was able to quantify an average of 397 ± 59 viable hookworm ova. Similarly, vital stain and PMA-qPCR methods quantified 644 ± 87 and 587 ± 91 viable ova, respectively. The numbers of viable ova estimated by the culture-based method were significantly (P < 0.05) lower than vital stain and PMA-qPCR methods. Therefore, both PMA-qPCR and vital stain methods appear to be suitable for the quantitative detection of viable hookworm ova. However, PMA-qPCR would be preferable over the vital stain method in scenarios where ova speciation is needed.

A Simplified, Low-Cost Method for Polarized Light Microscopy

PubMed Central

Maude, Richard J.; Buapetch, Wanchana; Silamut, Kamolrat

2009-01-01

Malaria pigment is an intracellular inclusion body that appears in blood and tissue specimens on microscopic examination and can help in establishing the diagnosis of malaria. In simple light microscopy, it can be difficult to discern from cellular background and artifacts. It has long been known that if polarized light microscopy is used, malaria pigment can be much easier to distinguish. However, this technique is rarely used because of the need for a relatively costly polarization microscope. We describe a simple and economical technique to convert any standard light microscope suitable for examination of malaria films into a polarization microscope. PMID:19861611

Magnetic trapping of buffer-gas-cooled chromium atoms and prospects for the extension to paramagnetic molecules

NASA Astrophysics Data System (ADS)

Bakker, Joost M.; Stoll, Michael; Weise, Dennis R.; Vogelsang, Oliver; Meijer, Gerard; Peters, Achim

2006-10-01

We report the successful buffer-gas cooling and magnetic trapping of chromium atoms with densities exceeding 1012 atoms per cm3 at a temperature of 350 mK for the trapped sample. The possibilities of extending the method to buffer-gas cool and magnetically trap molecules are discussed. To minimize the most important loss mechanism in magnetic trapping, molecules with a small spin spin interaction and a large rotational constant are preferred. Both the CrH (6Σ+ ground state) and MnH (7Σ+) radicals appear to be suitable systems for future experiments.

Estimating child mortality and modelling its age pattern for India.

PubMed

Roy, S G

1989-06-01

"Using data [for India] on proportions of children dead...estimates of infant and child mortality are...obtained by Sullivan and Trussell modifications of [the] Brass basic method. The estimate of child survivorship function derived after logit smoothing appears to be more reliable than that obtained by the Census Actuary. The age pattern of childhood mortality is suitably modelled by [a] Weibull function defining the probability of surviving from birth to a specified age and involving two parameters of level and shape. A recently developed linearization procedure based on [a] graphical approach is adopted for estimating the parameters of the function." excerpt

Finite-difference solution of the compressible stability eigenvalue problem

NASA Technical Reports Server (NTRS)

Malik, M. R.

1982-01-01

A compressible stability analysis computer code is developed. The code uses a matrix finite difference method for local eigenvalue solution when a good guess for the eigenvalue is available and is significantly more computationally efficient than the commonly used initial value approach. The local eigenvalue search procedure also results in eigenfunctions and, at little extra work, group velocities. A globally convergent eigenvalue procedure is also developed which may be used when no guess for the eigenvalue is available. The global problem is formulated in such a way that no unstable spurious modes appear so that the method is suitable for use in a black box stability code. Sample stability calculations are presented for the boundary layer profiles of a Laminar Flow Control (LFC) swept wing.

Visual field examination method using virtual reality glasses compared with the Humphrey perimeter.

PubMed

Tsapakis, Stylianos; Papaconstantinou, Dimitrios; Diagourtas, Andreas; Droutsas, Konstantinos; Andreanos, Konstantinos; Moschos, Marilita M; Brouzas, Dimitrios

2017-01-01

To present a visual field examination method using virtual reality glasses and evaluate the reliability of the method by comparing the results with those of the Humphrey perimeter. Virtual reality glasses, a smartphone with a 6 inch display, and software that implements a fast-threshold 3 dB step staircase algorithm for the central 24° of visual field (52 points) were used to test 20 eyes of 10 patients, who were tested in a random and consecutive order as they appeared in our glaucoma department. The results were compared with those obtained from the same patients using the Humphrey perimeter. High correlation coefficient ( r =0.808, P <0.0001) was found between the virtual reality visual field test and the Humphrey perimeter visual field. Visual field examination results using virtual reality glasses have a high correlation with the Humphrey perimeter allowing the method to be suitable for probable clinical use.

[The suitability of sending nursing home residents over 75 to emergency departments].

PubMed

Dang, Anne; Sanchez, Stéphane; Collart, Michèle; Mahmoudi, Rachid; Laplanche, David

The care provided to elderly people aged over 75 must be specific and multidisciplinary. An emergency department, which is seeing increasing numbers of patients passing through its doors, notably with the provision of an ambulatory care service, would not appear to be a suitable place for this fragile population, often with multiple pathologies. A study is looking at the suitability of the emergency department for nursing home residents, who have regular access to medical care, unlike elderly people living at home. Copyright © 2018. Published by Elsevier Masson SAS.

Diversity arrays technology (DArT) markers in apple for genetic linkage maps.

PubMed

Schouten, Henk J; van de Weg, W Eric; Carling, Jason; Khan, Sabaz Ali; McKay, Steven J; van Kaauwen, Martijn P W; Wittenberg, Alexander H J; Koehorst-van Putten, Herma J J; Noordijk, Yolanda; Gao, Zhongshan; Rees, D Jasper G; Van Dyk, Maria M; Jaccoud, Damian; Considine, Michael J; Kilian, Andrzej

2012-03-01

Diversity Arrays Technology (DArT) provides a high-throughput whole-genome genotyping platform for the detection and scoring of hundreds of polymorphic loci without any need for prior sequence information. The work presented here details the development and performance of a DArT genotyping array for apple. This is the first paper on DArT in horticultural trees. Genetic mapping of DArT markers in two mapping populations and their integration with other marker types showed that DArT is a powerful high-throughput method for obtaining accurate and reproducible marker data, despite the low cost per data point. This method appears to be suitable for aligning the genetic maps of different segregating populations. The standard complexity reduction method, based on the methylation-sensitive PstI restriction enzyme, resulted in a high frequency of markers, although there was 52-54% redundancy due to the repeated sampling of highly similar sequences. Sequencing of the marker clones showed that they are significantly enriched for low-copy, genic regions. The genome coverage using the standard method was 55-76%. For improved genome coverage, an alternative complexity reduction method was examined, which resulted in less redundancy and additional segregating markers. The DArT markers proved to be of high quality and were very suitable for genetic mapping at low cost for the apple, providing moderate genome coverage. ELECTRONIC SUPPLEMENTARY MATERIAL: The online version of this article (doi:10.1007/s11032-011-9579-5) contains supplementary material, which is available to authorized users.

Quantification and Statistical Analysis Methods for Vessel Wall Components from Stained Images with Masson's Trichrome

PubMed Central

Hernández-Morera, Pablo; Castaño-González, Irene; Travieso-González, Carlos M.; Mompeó-Corredera, Blanca; Ortega-Santana, Francisco

2016-01-01

Purpose To develop a digital image processing method to quantify structural components (smooth muscle fibers and extracellular matrix) in the vessel wall stained with Masson’s trichrome, and a statistical method suitable for small sample sizes to analyze the results previously obtained. Methods The quantification method comprises two stages. The pre-processing stage improves tissue image appearance and the vessel wall area is delimited. In the feature extraction stage, the vessel wall components are segmented by grouping pixels with a similar color. The area of each component is calculated by normalizing the number of pixels of each group by the vessel wall area. Statistical analyses are implemented by permutation tests, based on resampling without replacement from the set of the observed data to obtain a sampling distribution of an estimator. The implementation can be parallelized on a multicore machine to reduce execution time. Results The methods have been tested on 48 vessel wall samples of the internal saphenous vein stained with Masson’s trichrome. The results show that the segmented areas are consistent with the perception of a team of doctors and demonstrate good correlation between the expert judgments and the measured parameters for evaluating vessel wall changes. Conclusion The proposed methodology offers a powerful tool to quantify some components of the vessel wall. It is more objective, sensitive and accurate than the biochemical and qualitative methods traditionally used. The permutation tests are suitable statistical techniques to analyze the numerical measurements obtained when the underlying assumptions of the other statistical techniques are not met. PMID:26761643

Image processing for identification and quantification of filamentous bacteria in in situ acquired images.

PubMed

Dias, Philipe A; Dunkel, Thiemo; Fajado, Diego A S; Gallegos, Erika de León; Denecke, Martin; Wiedemann, Philipp; Schneider, Fabio K; Suhr, Hajo

2016-06-11

In the activated sludge process, problems of filamentous bulking and foaming can occur due to overgrowth of certain filamentous bacteria. Nowadays, these microorganisms are typically monitored by means of light microscopy, commonly combined with staining techniques. As drawbacks, these methods are susceptible to human errors, subjectivity and limited by the use of discontinuous microscopy. The in situ microscope appears as a suitable tool for continuous monitoring of filamentous bacteria, providing real-time examination, automated analysis and eliminating sampling, preparation and transport of samples. In this context, a proper image processing algorithm is proposed for automated recognition and measurement of filamentous objects. This work introduces a method for real-time evaluation of images without any staining, phase-contrast or dilution techniques, differently from studies present in the literature. Moreover, we introduce an algorithm which estimates the total extended filament length based on geodesic distance calculation. For a period of twelve months, samples from an industrial activated sludge plant were weekly collected and imaged without any prior conditioning, replicating real environment conditions. Trends of filament growth rate-the most important parameter for decision making-are correctly identified. For reference images whose filaments were marked by specialists, the algorithm correctly recognized 72 % of the filaments pixels, with a false positive rate of at most 14 %. An average execution time of 0.7 s per image was achieved. Experiments have shown that the designed algorithm provided a suitable quantification of filaments when compared with human perception and standard methods. The algorithm's average execution time proved its suitability for being optimally mapped into a computational architecture to provide real-time monitoring.

Microstructural and mechanical characteristics of porous iron prepared by powder metallurgy.

PubMed

Capek, Jaroslav; Vojtěch, Dalibor

2014-10-01

The demand for porous biodegradable load-bearing implants has been increasing recently. Based on investigations of biodegradable stents, porous iron may be a suitable material for such applications. In this study, we prepared porous iron samples with porosities of 34-51 vol.% by powder metallurgy using ammonium bicarbonate as a space-holder material. We studied sample microstructure (SEM-EDX and XRD), flexural and compressive behaviors (universal loading machine) and hardness HV5 (hardness tester) of the prepared samples. Sample porosity increased with the amount of spacer in the initial mixtures. Only the pore surfaces had insignificant oxidation and no other contamination was observed. Increasing porosity decreased the mechanical properties of the samples; although, the properties were still comparable with human bone and higher than those of porous non-metallic biomaterials and porous magnesium prepared in a similar way. Based on these results, powder metallurgy appears to be a suitable method for the preparation of porous iron for orthopedic applications. Copyright © 2014 Elsevier B.V. All rights reserved.

Alcohol imagery and branding, and age classification of films popular in the UK.

PubMed

Lyons, Ailsa; McNeill, Ann; Gilmore, Ian; Britton, John

2011-10-01

Exposure to alcohol products in feature films is a risk factor for use of alcohol by young people. This study was designed to document the extent to which alcohol imagery and brand appearances occur in popular UK films, and in relation to British Board of Film Classification (BBFC) age ratings intended to protect children and young people from harmful imagery. Alcohol appearances (classified as 'alcohol use, inferred alcohol use, other alcohol reference and alcohol brand appearances') were measured using 5-min interval coding of 300 films, comprising the 15 highest grossing films at the UK Box Office each year over a period of 20 years from 1989 to 2008. At least one alcohol appearance occurred in 86% of films, at least one episode of alcohol branding in 35% and nearly a quarter (23%) of all intervals analysed contained at least one appearance of alcohol. The occurrence of 'alcohol use and branded alcohol appearances' was particularly high in 1989, but the frequency of these and all other appearance categories changed little in subsequent years. Most films containing alcohol appearances, including 90% of those including 'alcohol brand appearances', were rated as suitable for viewing by children and young people. The most frequently shown brands were American beers: Budweiser, Miller and Coors. Alcohol appearances were similarly frequent in films originating from the UK, as from the USA. Alcohol imagery is extremely common in all films popular in the UK, irrespective of BBFC age classification. Given the relationship between exposure to alcohol imagery in films and use of alcohol by young people, we suggest that alcohol imagery should be afforded greater consideration in determining the suitability of films for viewing by children and young people.

Is Switzerland Suitable for the Invasion of Aedes albopictus?

PubMed Central

Neteler, Markus; Metz, Markus; Rocchini, Duccio; Rizzoli, Annapaola; Flacio, Eleonora; Engeler, Luca; Guidi, Valeria; Lüthy, Peter; Tonolla, Mauro

2013-01-01

Background Over the last 30 years, the Asian tiger mosquito, Aedes albopictus, has rapidly spread around the world. The European distribution comprises the Mediterranean basin with a first appearance in Switzerland in 2003. Early identification of the most suitable areas in Switzerland allowing progressive invasion by this species is considered crucial to suggest adequate surveillance and control plans. Methodology/Principal Findings We identified the most suitable areas for invasion and establishment of Ae. albopictus in Switzerland. The potential distribution areas linked to the current climatic suitability were assessed using remotely sensed land surface temperature data recorded by the MODIS satellite sensors. Suitable areas for adult survival and overwintering of diapausing eggs were also identified for future climatic conditions, considering two different climate change scenarios (A1B, A2) for the periods 2020–2049 and 2045–2074. At present, the areas around Lake Geneva in western Switzerland provide suitable climatic conditions for Ae. albopictus. In northern Switzerland, parts of the Rhine valley, around Lake Constance, as well as the surroundings of Lake Neuchâtel, appear to be suitable for the survival at least of adult Ae. albopictus. However, these areas are characterized by winters currently being too cold for survival and development of diapausing eggs. In southern Switzerland, Ae. albopictus is already well-established, especially in the Canton of Ticino. For the years 2020–2049, the predicted possible spread of the tiger mosquito does not differ significantly from its potential current distribution. However, important expansions are obtained if the period is extended to the years 2045–2074, when Ae. albopictus may invade large new areas. Conclusions/Significance Several parts of Switzerland provide suitable climatic conditions for invasion and establishment of Ae. albopictus. The current distribution and rapid spread in other European countries suggest that the tiger mosquito will colonize new areas in Switzerland in the near future. PMID:24349190

Is Switzerland suitable for the invasion of Aedes albopictus [corrected]?

PubMed

Neteler, Markus; Metz, Markus; Rocchini, Duccio; Rizzoli, Annapaola; Flacio, Eleonora; Engeler, Luca; Guidi, Valeria; Lüthy, Peter; Tonolla, Mauro

2013-01-01

Over the last 30 years, the Asian tiger mosquito, Aedes albopictus, has rapidly spread around the world. The European distribution comprises the Mediterranean basin with a first appearance in Switzerland in 2003. Early identification of the most suitable areas in Switzerland allowing progressive invasion by this species is considered crucial to suggest adequate surveillance and control plans. We identified the most suitable areas for invasion and establishment of Ae. albopictus in Switzerland. The potential distribution areas linked to the current climatic suitability were assessed using remotely sensed land surface temperature data recorded by the MODIS satellite sensors. Suitable areas for adult survival and overwintering of diapausing eggs were also identified for future climatic conditions, considering two different climate change scenarios (A1B, A2) for the periods 2020-2049 and 2045-2074. At present, the areas around Lake Geneva in western Switzerland provide suitable climatic conditions for Ae. albopictus. In northern Switzerland, parts of the Rhine valley, around Lake Constance, as well as the surroundings of Lake Neuchâtel, appear to be suitable for the survival at least of adult Ae. albopictus. However, these areas are characterized by winters currently being too cold for survival and development of diapausing eggs. In southern Switzerland, Ae. albopictus is already well-established, especially in the Canton of Ticino. For the years 2020-2049, the predicted possible spread of the tiger mosquito does not differ significantly from its potential current distribution. However, important expansions are obtained if the period is extended to the years 2045-2074, when Ae. albopictus may invade large new areas. Several parts of Switzerland provide suitable climatic conditions for invasion and establishment of Ae. albopictus. The current distribution and rapid spread in other European countries suggest that the tiger mosquito will colonize new areas in Switzerland in the near future.

Application of superconducting coils to the NASA prototype magnetic balance

NASA Technical Reports Server (NTRS)

Haldeman, C. W.; Kraemer, R. A.; Phey, S. W.; Alishahi, M. M.; Covert, E. E.

1981-01-01

Application of superconducting coils to a general purpose magnetic balance was studied. The most suitable currently available superconducting cable for coils appears to be a bundle of many fine wires which are transposed and are mechanically confined. Sample coils were tested at central fields up to .5 Tesla, slewing rates up to 53 Tesla/ sec and frequencies up to 30 Hz. The ac losses were measured from helium boil-off and were approximately 20% higher than those calculated. Losses were dominated by hysteresis and a model for loss calculation which appears suitable for design purposes is presented along with computer listings. Combinations of two coils were also tested and interaction losses are reported. Two feasible geometries are also presented for prototype magnetic balance using superconductors.

Treatment of constraints in the stochastic quantization method and covariantized Langevin equation

NASA Astrophysics Data System (ADS)

Ikegami, Kenji; Kimura, Tadahiko; Mochizuki, Riuji

1993-04-01

We study the treatment of the constraints in the stochastic quantization method. We improve the treatment of the stochastic consistency condition proposed by Namiki et al. by suitably taking into account the Ito calculus. Then we obtain an improved Langevi equation and the Fokker-Planck equation which naturally leads to the correct path integral quantization of the constrained system as the stochastic equilibrium state. This treatment is applied to an O( N) non-linear α model and it is shown that singular terms appearing in the improved Langevin equation cancel out the σ n(O) divergences in one loop order. We also ascertain that the above Langevin equation, rewritten in terms of idependent variables, is actually equivalent to the one in the general-coordinate transformation covariant and vielbein-rotation invariant formalish.

Evaluation of statistical treatments of left-censored environmental data using coincident uncensored data sets. II. Group comparisons

USGS Publications Warehouse

Antweiler, Ronald C.

2015-01-01

The main classes of statistical treatments that have been used to determine if two groups of censored environmental data arise from the same distribution are substitution methods, maximum likelihood (MLE) techniques, and nonparametric methods. These treatments along with using all instrument-generated data (IN), even those less than the detection limit, were evaluated by examining 550 data sets in which the true values of the censored data were known, and therefore “true” probabilities could be calculated and used as a yardstick for comparison. It was found that technique “quality” was strongly dependent on the degree of censoring present in the groups. For low degrees of censoring (<25% in each group), the Generalized Wilcoxon (GW) technique and substitution of √2/2 times the detection limit gave overall the best results. For moderate degrees of censoring, MLE worked best, but only if the distribution could be estimated to be normal or log-normal prior to its application; otherwise, GW was a suitable alternative. For higher degrees of censoring (each group >40% censoring), no technique provided reliable estimates of the true probability. Group size did not appear to influence the quality of the result, and no technique appeared to become better or worse than other techniques relative to group size. Finally, IN appeared to do very well relative to the other techniques regardless of censoring or group size.

MoS2 thin films prepared by sulfurization

NASA Astrophysics Data System (ADS)

Sojková, M.; Chromik, Å.; Rosová, A.; Dobročka, E.; Hutár, P.; Machajdík, D.; Kobzev, A. P.; Hulman, M.

2017-08-01

Sulfurization of a Mo layer is one of the most used methods for preparation of thin MoS2 films. In the method, a sulfur powder and Mo covered substrate are placed in different positions within a furnace, and heated separately. This requires a furnace having at least two zones. Here, we present a simplified version of the method where a one-zone tube furnace was used. A molybdenum film on a substrate and a sulfur powder were placed in the center of the furnace and heated at temperatures above 800°C. Mo films transform into MoS2 in vapors of sulphur at high temperatures. As-prepared films were characterized by number of techniques including X-ray diffraction (XRD), atomic force microscopy (AFM), transmission electron microscopy (TEM), Raman, Rutherford backscattering (RBS) and X-ray photoelectron spectroscopy (XPS). It appears that one-zone sulfurization, with just one annealing temperature used, is a suitable method for fabrication of MoS2 thin films. This method is fast, cheap and easy to scale up.

Comparison of analytical methods for the determination of histamine in reference canned fish samples

NASA Astrophysics Data System (ADS)

Jakšić, S.; Baloš, M. Ž.; Mihaljev, Ž.; Prodanov Radulović, J.; Nešić, K.

2017-09-01

Two screening methods for histamine in canned fish, an enzymatic test and a competitive direct enzyme-linked immunosorbent assay (CD-ELISA), were compared with the reversed-phase liquid chromatography (RP-HPLC) standard method. For enzymatic and CD-ELISA methods, determination was conducted according to producers’ manuals. For RP-HPLC, histamine was derivatized with dansyl-chloride, followed by RP-HPLC and diode array detection. Results of analysis of canned fish, supplied as reference samples for proficiency testing, showed good agreement when histamine was present at higher concentrations (above 100 mg kg-1). At a lower level (16.95 mg kg-1), the enzymatic test produced some higher results. Generally, analysis of four reference samples according to CD-ELISA and RP-HPLC showed good agreement for histamine determination (r=0.977 in concentration range 16.95-216 mg kg-1) The results show that the applied enzymatic test and CD-ELISA appeared to be suitable screening methods for the determination of histamine in canned fish.

Quantum Entanglement as a Diagnostic of Phase Transitions in Disordered Fractional Quantum Hall Liquids.

PubMed

Liu, Zhao; Bhatt, R N

2016-11-11

We investigate the disorder-driven phase transition from a fractional quantum Hall state to an Anderson insulator using quantum entanglement methods. We find that the transition is signaled by a sharp increase in the sensitivity of a suitably averaged entanglement entropy with respect to disorder-the magnitude of its disorder derivative appears to diverge in the thermodynamic limit. We also study the level statistics of the entanglement spectrum as a function of disorder. However, unlike the dramatic phase-transition signal in the entanglement entropy derivative, we find a gradual reduction of level repulsion only deep in the Anderson insulating phase.

Bioactives from microalgal dinoflagellates.

PubMed

Gallardo-Rodríguez, J; Sánchez-Mirón, A; García-Camacho, F; López-Rosales, L; Chisti, Y; Molina-Grima, E

2012-01-01

Dinoflagellate microalgae are an important source of marine biotoxins. Bioactives from dinoflagellates are attracting increasing attention because of their impact on the safety of seafood and potential uses in biomedical, toxicological and pharmacological research. Here we review the potential applications of dinoflagellate toxins and the methods for producing them. Only sparing quantities of dinoflagellate toxins are generally available and this hinders bioactivity characterization and evaluation in possible applications. Approaches to production of increased quantities of dinoflagellate bioactives are discussed. Although many dinoflagellates are fragile and grow slowly, controlled culture in bioreactors appears to be generally suitable for producing many of the metabolites of interest. Copyright © 2012 Elsevier Inc. All rights reserved.

Human body preservation – old and new techniques

PubMed Central

Brenner, Erich

2014-01-01

This review deals with the art of (anatomical) embalming. The first part contains a brief historical review of the history of embalming, starting with ancient cultures such as the Egyptians and the lesser known Chinchorro culture, then going down the centuries and describing the anatomical techniques developed over the last two centuries. The second part deals in detail with the chemicals used for embalming purposes. The third part deals with several approaches to evaluating embalming methods, their suitability for biomechanical testing, antimicrobial properties, histological appearance, and usability. The fourth and final part analyze the European Biocidal Products Directive (98/8/EC) in the light of embalming. PMID:24438435

Human body preservation - old and new techniques.

PubMed

Brenner, Erich

2014-03-01

This review deals with the art of (anatomical) embalming. The first part contains a brief historical review of the history of embalming, starting with ancient cultures such as the Egyptians and the lesser known Chinchorro culture, then going down the centuries and describing the anatomical techniques developed over the last two centuries. The second part deals in detail with the chemicals used for embalming purposes. The third part deals with several approaches to evaluating embalming methods, their suitability for biomechanical testing, antimicrobial properties, histological appearance, and usability. The fourth and final part analyze the European Biocidal Products Directive (98/8/EC) in the light of embalming. © 2014 Anatomical Society.

Robust Assignment Of Eigensystems For Flexible Structures

NASA Technical Reports Server (NTRS)

Juang, Jer-Nan; Lim, Kyong B.; Junkins, John L.

1992-01-01

Improved method for placement of eigenvalues and eigenvectors of closed-loop control system by use of either state or output feedback. Applied to reduced-order finite-element mathematical model of NASA's MAST truss beam structure. Model represents deployer/retractor assembly, inertial properties of Space Shuttle, and rigid platforms for allocation of sensors and actuators. Algorithm formulated in real arithmetic for efficient implementation. Choice of open-loop eigenvector matrix and its closest unitary matrix believed suitable for generating well-conditioned eigensystem with small control gains. Implication of this approach is that element of iterative search for "optimal" unitary matrix appears unnecessary in practice for many test problems.

Evaluation of antibacterial properties of novel phthalocyanines against Escherichia coli--comparison of analytical methods.

PubMed

Mikula, Premysl; Kalhotka, Libor; Jancula, Daniel; Zezulka, Stepan; Korinkova, Radka; Cerny, Jiri; Marsalek, Blahoslav; Toman, Petr

2014-09-05

We analyzed antibacterial effects of several novel phthalocyanines against Escherichia coli and evaluated the suitability of flow cytometry for the detection of antibacterial effects of phthalocyanines in comparison with routinely used cultivation. After 3h of exposure under cool white light eight cationic phthalocyanines showed very high antibacterial activity in the concentration of 2.00 mg L(-1) and four of them were even efficient in the concentration of 0.20 mg L(-1). Antibacterial activity of neutral and anionic compounds was considerably lower or even negligible. No antibacterial effect was detected when bacteria were exposed without illumination. Binding affinity to bacterial cells was found to represent an important parameter influencing phthalocyanine antibacterial activity that can be modified by total charge of peripheral substituents and by the presence of suitable functional groups inside them. Agglomeration of cells observed in suspensions treated with a higher concentration of certain cationic phthalocyanines (the strongest binders to bacterial membrane) affected cytometric measurements of total cell counts, thus without appropriate pretreatment of the sample before analysis this parameter seems not to be fully valid in the evaluation of phthalocyanine antibacterial activity. Cytometric measurement of cell membrane integrity appears to be a suitable and even more sensitive parameter than cultivation. Copyright © 2014 Elsevier B.V. All rights reserved.

Deblocking of mobile stereo video

NASA Astrophysics Data System (ADS)

Azzari, Lucio; Gotchev, Atanas; Egiazarian, Karen

2012-02-01

Most of candidate methods for compression of mobile stereo video apply block-transform based compression based on the H-264 standard with quantization of transform coefficients driven by quantization parameter (QP). The compression ratio and the resulting bit rate are directly determined by the QP level and high compression is achieved for the price of visually noticeable blocking artifacts. Previous studies on perceived quality of mobile stereo video have revealed that blocking artifacts are the most annoying and most influential in the acceptance/rejection of mobile stereo video and can even completely cancel the 3D effect and the corresponding quality added value. In this work, we address the problem of deblocking of mobile stereo video. We modify a powerful non-local transform-domain collaborative filtering method originally developed for denoising of images and video. The method employs grouping of similar block patches residing in spatial and temporal vicinity of a reference block in filtering them collaboratively in a suitable transform domain. We study the most suitable way of finding similar patches in both channels of stereo video and suggest a hybrid four-dimensional transform to process the collected synchronized (stereo) volumes of grouped blocks. The results benefit from the additional correlation available between the left and right channel of the stereo video. Furthermore, addition sharpening is applied through an embedded alpha-rooting in transform domain, which improve the visual appearance of the deblocked frames.

A novel finite element analysis of three-dimensional circular crack

NASA Astrophysics Data System (ADS)

Ping, X. C.; Wang, C. G.; Cheng, L. P.

2018-06-01

A novel singular element containing a part of the circular crack front is established to solve the singular stress fields of circular cracks by using the numerical series eigensolutions of singular stress fields. The element is derived from the Hellinger-Reissner variational principle and can be directly incorporated into existing 3D brick elements. The singular stress fields are determined as the system unknowns appearing as displacement nodal values. The numerical studies are conducted to demonstrate the simplicity of the proposed technique in handling fracture problems of circular cracks. The usage of the novel singular element can avoid mesh refinement near the crack front domain without loss of calculation accuracy and velocity of convergence. Compared with the conventional finite element methods and existing analytical methods, the present method is more suitable for dealing with complicated structures with a large number of elements.

Impregnation of soft biological specimens with thermosetting resins and elastomers.

PubMed

von Hagens, G

1979-06-01

A new method for impregnation of biological specimens with thermosetting resins and elastomers is described. The method has the advantage that the original relief of the surface is retained. The impregnation is carried out by utilizing the difference between the high vapor tension of the intermedium (e.g., methylene chloride) and the low vapor tension of the solution to be polymerized. After impregnation, the specimen is subject to polymerization conditions without surrounding embedding material. The optical and mechanical properties can be selected by proper choice from various kinds of resins and different procedures, for example, by complete or incomplete impregnation. Acrylic resins, polyester resins, epoxy resins, polyurethanes and silicone rubber have been found suitable for the method. Excellent results have been obtained using transparent silicone rubber since after treatment the specimens are still flexible and resilient, and have retained their natural appearance.

[Antimicrobial susceptibility testing of anaerobic bacteria].

PubMed

García-Sánchez, José E; García-Sánchez, Enrique; García-García, María Inmaculada

2014-02-01

The anaerobic bacteria resistance to antibiotics is increasing, and even has appeared against the most active of those, like metronidazol and carbapenems. This fact forces to make and periodical sensibility tests -at least in the most aggressive and virulent species, in cases that they are isolated from life locations and in the absence of therapeutic response- to check the local sensibility and to establish suitable empiric therapies, all based on multicentric studies carried out in order to this or well to check the activity of new antibiotics. For the laboratory routine, the easiest sensibility method is the E-test/MIC evaluator. Another alternative is microdilution, that's only normalized for Bacteroides. There are preliminary facts that allow the use of disc diffusion method in some species of Bacteroides and Clostridium. For the temporal and multicentric studies, the procedure is dilution in agar plate, the reference method. Copyright © 2014 Elsevier España, S.L. All rights reserved.

Selection of sugar cane families by using BLUP and multi-diverse analyses for planting in the Brazilian savannah.

PubMed

Barbosa, M H P; Ferreira, A; Peixoto, L A; Resende, M D V; Nascimento, M; Silva, F F

2014-03-12

This study evaluated different strategies to select sugar cane families and obtain clones adapted to the conditions of the Brazilian savannah. Specifically, 7 experiments were conducted, with 10 full sib families, and 2 witnesses in common to all experiments, in each experiment. The plants were grown in random blocks, with witnesses in common (incomplete blocks), and 6 repetitions of each experiment. The data were analyzed through the methodology of mixed patterns, in which the matrices of kinship between the families were identified by the method of restricted maximum likelihood. The characteristics that were evaluated included soluble solids content (BRIX), BRIX ton/ha, average mass of a culm, number of culms/m, and tons of culms/ha. A multi-diverse alternative based on the analysis of groupings by using the UPGMA method was used to identify the most viable families for selection, when considering the genotypic effects on all characteristics. This method appeared suitable for the selection of families, with 5 family groups being formed. The families that formed Group 2 appeared superior to all other families for all the evaluated characteristics. It is recommended that the families in Group 2 are preferentially used in sugar cane improvement programs to obtain varieties optimally adapted to the conditions of the Brazilian savannah.

Participatory methods in pediatric participatory research: a systematic review.

PubMed

Haijes, Hanneke A; van Thiel, Ghislaine J M W

2016-05-01

Meaningful child participation in medical research is seen as important. In order to facilitate further development of participatory research, we performed a systematic literature study to describe and assess the available knowledge on participatory methods in pediatric research. A search was executed in five databases: PubMed, CINAHL, PsycINFO, Scopus, and Cochrane. After careful screening of relevant papers, finally 24 documents were included in our analysis. Literature on participatory methods in pediatric research appears generally to be descriptive, whereby high-quality evidence is lacking. Overall, five groups of participatory methods for children could be distinguished: observational, verbal, written, visual, and active methods. The choice for one of these methods should be based on the child's age, on social and demographic characteristics, and on the research objectives. To date, these methods are still solely used for obtaining data, yet they are suitable for conducting meaningful participation. This may result in a successful partnership between children and researchers. Researchers conducting participatory research with children can use this systematic review in order to weigh the current knowledge about the participatory methods presented.

The Drake Equation

NASA Astrophysics Data System (ADS)

Vakoch, Douglas A.; Dowd, Matthew F.; Drake, Frank

2015-07-01

List of contributors; Foreword Frank Drake; Preface; Acknowledgements; Introduction Steven Dick; 1. Rate of formation of stars suitable for the development of intelligent life, R*, pre-1961 David DeVorkin; 2. Rate of formation of stars suitable for the development of intelligent life, R*, 1961 to the present Patrick François and Danielle Briot; 3. Fraction of stars with planetary systems, fp, pre-1961 Matthew F. Dowd; 4. Fraction of stars with planetary systems, fp, 1961 to the present Chris Impey; 5. Number of planets, per solar system, with an environment suitable for life, ne, pre-1961 Florence Raulin Cerceau; 6. Number of planets, per solar system, with an environment suitable for life, ne, 1961 to the present Danielle Briot and Jean Schneider; 7. Fraction of suitable planets on which life actually appears, fl, pre-1961 Stephané Tirard; 8. Fraction of suitable planets on which life actually appears, fl, 1961 to the present David J. Des Marais; 9. Fraction of life-bearing planets on which intelligent life emerges, fl, pre-1961 Michael Crowe; 10. Fraction of life-bearing planets on which intelligent life emerges, fl, 1961 to the present Lori Marino; 11. Fraction of civilizations that develop a technology that releases detectable signs of their existence into space, fc, pre-1961 Florence Raulin Cerceau; 12. Fraction of civilizations that develop a technology that releases detectable signs of their existence into space, fc, 1961 to the present Seth Shostak; 13. Length of time such civilizations release detectable signals into space, L, pre-1961 David Dunér; 14. Length of time such civilizations release detectable signals into space, L, 1961 to the present Garry Chick; Afterword Paul Davies; Index.

[Effects of future climate change on climatic suitability of rubber plantation in China].

PubMed

Liu, Shao-jun; Zhou, Guang-sheng; Fang, Shi-bo; Zhang, Jing-hong

2015-07-01

Global warming may seriously affect the climatic suitability distribution of rubber plantation in China. Five main climate factors affecting rubber planting were mean temperature of the coldest month, mean extremely minimum temperature, the number of monthly, mean temperature ≥18 °C, annual mean temperature and annual mean precipitation. Climatic suitability areas of rubber plantation in 1981-2010, 2041-2060, 2061-2080 were analyzed by the maximum entropy model based on the five main climate factors and the climate data of 1981-2010 and RCP4.5 scenario data. The results showed that under the background of the future climate change, the climatic suitability area of rubber plantation would have a trend of expansion to the north in 2041-2060, 2061-2080. The climatic suitability areas of rubber plantation in 2041-2060 and 2061-2080 increased more obviously than in 1981-2010. The suitable area and optimum area would increase, while the less suitable area would decrease. The climatic suitability might change in some areas, such as the total suitable area would decrease in Yunnan Province, and the suitability grade in both Jinghong and Mengna would change from optimum area to suitable area. However, the optimum area of rubber plantation would increase significantly in Hainan Island and Leizhou Peninsula of Guangdong Province, and a new less suitable area of rubber planting would appear in Taiwan Island due to the climate change.

Nanoscale array structures suitable for surface enhanced raman scattering and methods related thereto

DOEpatents

Bond, Tiziana C.; Miles, Robin; Davidson, James C.; Liu, Gang Logan

2014-07-22

Methods for fabricating nanoscale array structures suitable for surface enhanced Raman scattering, structures thus obtained, and methods to characterize the nanoscale array structures suitable for surface enhanced Raman scattering. Nanoscale array structures may comprise nanotrees, nanorecesses and tapered nanopillars.

Nanoscale array structures suitable for surface enhanced raman scattering and methods related thereto

DOEpatents

Bond, Tiziana C.; Miles, Robin; Davidson, James C.; Liu, Gang Logan

2015-07-14

Methods for fabricating nanoscale array structures suitable for surface enhanced Raman scattering, structures thus obtained, and methods to characterize the nanoscale array structures suitable for surface enhanced Raman scattering. Nanoscale array structures may comprise nanotrees, nanorecesses and tapered nanopillars.

Nanoscale array structures suitable for surface enhanced raman scattering and methods related thereto

DOEpatents

Bond, Tiziana C; Miles, Robin; Davidson, James; Liu, Gang Logan

2015-11-03

Methods for fabricating nanoscale array structures suitable for surface enhanced Raman scattering, structures thus obtained, and methods to characterize the nanoscale array structures suitable for surface enhanced Raman scattering. Nanoscale array structures may comprise nanotrees, nanorecesses and tapered nanopillars.

Italian recommendations on dental support in the treatment of adult obstructive sleep apnea syndrome (OSAS)

PubMed Central

Levrini, Luca; Sacchi, Franco; Milano, Francesca; Polimeni, Antonella; Cozza, Paolo; Bernkopf, Edoardo; Segù, Marzia; Zucconi, Marco; Vicini, Claudio; Brunello, Enrico

2015-01-01

Summary Background The aim of the present article is to present a set of proposed clinical recommendations aimed at Italian dentists involved in the management of patients with obstructive sleep apnea syndrome or snoring. Methods With the purpose of creating a study group, some of the most important Italian scientific societies operating in fields relevant to the issue of sleep medicine in dentistry were asked to appoint a representative. Each member of the study group was required to answer questions regarding the clinical management of OSAS and snoring. Results Oral appliances can be used to treat: - simple snoring, in patients who do not respond to, or do not appear to be suitable candidates for behavioral measures such as weight loss or positional therapy; - mild or moderate OSAS, in patients who prefer OAs to continuous positive airway pressure (CPAP) or who are not suitable candidates for CPAP, because of its failure or failure of behavioral approaches like weight loss or positional therapy; - severe OSAS, in patients who do not respond to or do not tolerate CPAP and in whom no indication for either maxillofacial or ENT surgery appears applicable. Conclusions The application of oral appliances is highly desirable in cases of simple snoring or mild to moderate OSAS, whereas considerable caution is warranted when treating severe OSAS. It is fundamental to ensure that the patient understands his problem and, at the same time, to present all the various treatment options. PMID:26941893

Microencapsulation of Bioactive Principles with an Airless Spray-Gun Suitable for Processing High Viscous Solutions

PubMed Central

Cocchietto, Moreno; Blasi, Paolo; Lapasin, Romano; Moro, Chiara; Gallo, Davide; Sava, Gianni

2013-01-01

Purpose: to design, assemble and test a prototype of a novel production plant, suitable for producing microparticles (MPs) by processing highly viscous feed solutions (FSs). Methods: the prototype has been built using a commercial air compressor, a piston pump, an airless spray-gun, a customized air-treatment section, a timer, a rotating base, and a filtration section. Preliminary prototype parameter setting was carried out to individuate the best performing nozzle’s dimension, the nebulization timing, and the CaCl2 concentration in the gelation fluid. In addition, prototype throughput (1 L to 5 L) and the range of practicable feed solution (FS) viscosities were assayed. A set of four batches was prepared in order to characterize the MPs, in terms of mean particle size and distribution, flow properties, swelling, encapsulation efficiency and release. Results: according to a qualitative scoring, the large nozzle was suitable to nebulize FSs at a higher alginate concentration. Conversely, the small nozzle performed better in the processing of FSs with an alginate concentration up to 2% w/v. Only at the highest degree of viscosity, corresponding to 5% w/v of alginate, the FS processing was not technically possible. Among the CaCl2 concentrations considered, 15% w/v was recognized as the most versatile. The prototype appears to be convenient and suitable to grant a high yield starting from 2 L of FS. The flow behavior of the FSs assayed can be satisfactorily described with the Carreau-Yasuda equation and the throughput begins to slightly decrease for FSs at alginate concentrations exceeding 3% w/v. MP morphology was irregular with crumpled shape. The angle of repose indicates a good flowability and the release studies showed gastro-resistance and potential prolonged release applications. Conclusions: the novel prototype of production plant is suitable to process large amounts (2 L or more) of FSs, characterized by a high viscosity, to produce MPs suitable for bioactive principle delivery. PMID:24956192

A novel multi-target regression framework for time-series prediction of drug efficacy.

PubMed

Li, Haiqing; Zhang, Wei; Chen, Ying; Guo, Yumeng; Li, Guo-Zheng; Zhu, Xiaoxin

2017-01-18

Excavating from small samples is a challenging pharmacokinetic problem, where statistical methods can be applied. Pharmacokinetic data is special due to the small samples of high dimensionality, which makes it difficult to adopt conventional methods to predict the efficacy of traditional Chinese medicine (TCM) prescription. The main purpose of our study is to obtain some knowledge of the correlation in TCM prescription. Here, a novel method named Multi-target Regression Framework to deal with the problem of efficacy prediction is proposed. We employ the correlation between the values of different time sequences and add predictive targets of previous time as features to predict the value of current time. Several experiments are conducted to test the validity of our method and the results of leave-one-out cross-validation clearly manifest the competitiveness of our framework. Compared with linear regression, artificial neural networks, and partial least squares, support vector regression combined with our framework demonstrates the best performance, and appears to be more suitable for this task.

A novel multi-target regression framework for time-series prediction of drug efficacy

PubMed Central

Li, Haiqing; Zhang, Wei; Chen, Ying; Guo, Yumeng; Li, Guo-Zheng; Zhu, Xiaoxin

2017-01-01

Excavating from small samples is a challenging pharmacokinetic problem, where statistical methods can be applied. Pharmacokinetic data is special due to the small samples of high dimensionality, which makes it difficult to adopt conventional methods to predict the efficacy of traditional Chinese medicine (TCM) prescription. The main purpose of our study is to obtain some knowledge of the correlation in TCM prescription. Here, a novel method named Multi-target Regression Framework to deal with the problem of efficacy prediction is proposed. We employ the correlation between the values of different time sequences and add predictive targets of previous time as features to predict the value of current time. Several experiments are conducted to test the validity of our method and the results of leave-one-out cross-validation clearly manifest the competitiveness of our framework. Compared with linear regression, artificial neural networks, and partial least squares, support vector regression combined with our framework demonstrates the best performance, and appears to be more suitable for this task. PMID:28098186

Detection of Legionella pneumophila by PCR-ELISA method in industrial cooling tower water.

PubMed

Soheili, Majid; Nejadmoghaddam, Mohammad Reza; Babashamsi, Mohammad; Ghasemi, Jamileh; Jeddi Tehrani, Mahmood

2007-11-15

Water supply and Cooling Tower Water (CTW) are among the most common sources of Legionella pneumophila (LP) contamination. A nonradio active method is described to detect LP in industrial CTW samples. DNA was purified and amplified by nested -PCR with amplimers specific for the 16s rRNA gene of LP. The 5' end biotinylated oligomer probe was immobilized on sterptavidin B coated microtiter plates. The nested-PCR product was labeled with digoxigenin and then hybridized with 5'-biotinylated probes. The amplification products were detected by using proxidase-labled anti dioxygenin antibody in a colorimetric reaction. The assay detected LP present in 1 L of 5 CTW samples examined. All of the samples were Legionella positive in both culture and PCR-ELISA methods. The PCR-ELISA assay appears to exhibit high specificity and is a more rapid technique in comparison with bacterial culture method. Thus could prove suitable for use in the routine examination of industrial CTW contamination.

An effective hand vein feature extraction method.

PubMed

Li, Haigang; Zhang, Qian; Li, Chengdong

2015-01-01

As a new authentication method developed years ago, vein recognition technology features the unique advantage of bioassay. This paper studies the specific procedure for the extraction of hand back vein characteristics. There are different positions used in the collecting process, so that a suitable intravenous regional orientation method is put forward, allowing the positioning area to be the same for all hand positions. In addition, to eliminate the pseudo vein area, the valley regional shape extraction operator can be improved and combined with multiple segmentation algorithms. The images should be segmented step by step, making the vein texture to appear clear and accurate. Lastly, the segmented images should be filtered, eroded, and refined. This process helps to filter the most of the pseudo vein information. Finally, a clear vein skeleton diagram is obtained, demonstrating the effectiveness of the algorithm. This paper presents a hand back vein region location method. This makes it possible to rotate and correct the image by working out the inclination degree of contour at the side of hand back.

A finite element based method for solution of optimal control problems

NASA Technical Reports Server (NTRS)

Bless, Robert R.; Hodges, Dewey H.; Calise, Anthony J.

1989-01-01

A temporal finite element based on a mixed form of the Hamiltonian weak principle is presented for optimal control problems. The mixed form of this principle contains both states and costates as primary variables that are expanded in terms of elemental values and simple shape functions. Unlike other variational approaches to optimal control problems, however, time derivatives of the states and costates do not appear in the governing variational equation. Instead, the only quantities whose time derivatives appear therein are virtual states and virtual costates. Also noteworthy among characteristics of the finite element formulation is the fact that in the algebraic equations which contain costates, they appear linearly. Thus, the remaining equations can be solved iteratively without initial guesses for the costates; this reduces the size of the problem by about a factor of two. Numerical results are presented herein for an elementary trajectory optimization problem which show very good agreement with the exact solution along with excellent computational efficiency and self-starting capability. The goal is to evaluate the feasibility of this approach for real-time guidance applications. To this end, a simplified two-stage, four-state model for an advanced launch vehicle application is presented which is suitable for finite element solution.

Quality of Patient Information Websites About Congenital Heart Defects: Mixed-Methods Study of Perspectives Among Individuals With Experience of a Prenatal Diagnosis.

PubMed

Carlsson, Tommy; Melander Marttala, Ulla; Wadensten, Barbro; Bergman, Gunnar; Axelsson, Ove; Mattsson, Elisabet

2017-09-12

When a heart defect is prenatally diagnosed in the fetus, expectant parents experience a great need for information about various topics. After the diagnosis, the Web is used for supplemental information, and the scarcity of research calls attention to the need to explore patient information websites from the perspectives of the intended consumers. The overarching aim of this study was to explore the quality of Swedish patient information websites about congenital heart defects, from the perspectives of individuals with experience of a prenatal diagnosis of congenital heart defect in the fetus. This was a mixed-methods study of websites identified through systematic searches in the two most used Web-based search engines. Of the total 80 screened hits, 10 hits led to patient information websites about congenital heart defects. A quality assessment tool inspired by a previous study was used to evaluate each website's appearance, details, relevance, suitability, information about treatment choices, and overall quality. Answers were given on a 5-point Likert scale, ranging from 1, representing the lowest score, to 5, representing the highest score. Each website was assessed individually by persons with experience of continued (n=4) and terminated (n=5) pregnancy following a prenatal diagnosis. Assessments were analyzed with Kendall's coefficient of concordance W, Mann-Whitney U test, Friedman's test, and a Wilcoxon-Nemenyi-McDonald-Thompson test. In addition, each assessor submitted written responses to open-ended questions in the quality assessment tool, and two joint focus group discussions were conducted with each group of assessors. The qualitative data were analyzed with inductive manifest content analysis. Assessments represented a low score (median=2.0) for treatment choices and moderate scores (median=3.0) for appearance, details, relevance, suitability, and overall quality. No website had a median of the highest achievable score for any of the questions in the quality assessment tool. Medians of the lowest achievable score were found in questions about treatment choices (n=4 websites), details (n=2 websites), suitability (n=1 website), and overall quality (n=1 website). Websites had significantly different scores for appearance (P=.01), details (P<.001), relevance (P<.001), suitability (P<.001), treatment choices (P=.04), and overall quality (P<.001). The content analysis of the qualitative data generated six categories: (1) advertisements, (2) comprehensiveness, (3) design, (4) illustrations and pictures, (5) language, and (6) trustworthiness. Various issues with the included websites were highlighted, including the use of inappropriate advertisements, biased information, poor illustrations, complex language, and poor trustworthiness. From the perspectives of the intended consumers, patient information websites about congenital heart defects are, to a large extent, inadequate tools for supplemental information following a prenatal diagnosis. Health professionals should initiate discussions with patients about their intentions to use the Web, inform them about the varied quality in the Web-based landscape, and offer recommendations for appropriate Web-based sources. ©Tommy Carlsson, Ulla Melander Marttala, Barbro Wadensten, Gunnar Bergman, Ove Axelsson, Elisabet Mattsson. Originally published in the Interactive Journal of Medical Research (http://www.i-jmr.org/), 12.09.2017.

Measuring the Environment for Friendliness Toward Physical Activity: A Comparison of the Reliability of 3 Questionnaires

PubMed Central

Brownson, Ross C.; Chang, Jen Jen; Eyler, Amy A.; Ainsworth, Barbara E.; Kirtland, Karen A.; Saelens, Brian E.; Sallis, James F.

2004-01-01

Objectives. We tested the reliability of 3 instruments that assessed social and physical environments. Methods. We conducted a test–retest study among US adults (n = 289). We used telephone survey methods to measure suitableness of the perceived (vs objective) environment for recreational physical activity and nonmotorized transportation. Results. Most questions in our surveys that attempted to measure specific characteristics of the built environment showed moderate to high reliability. Questions about the social environment showed lower reliability than those that assessed the physical environment. Certain blocks of questions appeared to be selectively more reliable for urban or rural respondents. Conclusions. Despite differences in content and in response formats, all 3 surveys showed evidence of reliability, and most items are now ready for use in research and in public health surveillance. PMID:14998817

Methods for the Identification of Aircraft Tubing of Plain Carbon Steel and Chromium-Molybdenum Steel

NASA Technical Reports Server (NTRS)

Mutchler, W H; Buzzard, R W

1930-01-01

The survey of the possibilities for distinguishing between plain carbon and chromium-molybdenum steel tubing included the Herbert pendulum hardness, magnetic, sparks, and chemical tests. The Herbert pendulum test has the disadvantages of all hardness tests in being limited to factory use and being applicable only to scale-free, normalized material. The small difference in the range of hardness values between plain carbon and chromium-molybdenum steels is likewise a disadvantage. The Rockwell hardness test, at present used in the industry for this purpose, is much more reliable. It may be concluded on the basis of the experiments performed that of all methods surveyed, spark testing appears to be, at present, the most suitable for factory use from the standpoint of speed, accuracy, nondestructiveness and reliability. It is also applicable for field use.

Influence of the sintering temperature on the electrical properties of Ce-doped WO3 ceramics prepared from nano-powders

NASA Astrophysics Data System (ADS)

Dong, Liang; Chen, Han-Jun; Wang, Yu; Li, De-Zhu; Li, Tong-Ye; Zhao, Yong

2007-04-01

Using a nm-level powder fabricated by a wet chemical method as precursor, the CeO2-doped WO3 ceramics were prepared by the conventional solid state reaction at sintering temperatures from 600 to 1100 °C. The x-ray diffraction analysis reveals the coexistence of different WO3 phases in the samples sintered at temperatures below 900 °C, whereas a single phase appears in the samples sintered above 1000 °C. No new Ce-W compound appears. As the sintering temperature increases, the electrical properties of the samples display an interesting transformation from linear to nonlinear behaviour. The measurements of scanning electron microscope, complex impedance and electrical stability indicate that a lot of grain boundary regions in the samples sintered at low temperatures strongly influences the electrical transportation. Therefore, the electrical nonlinearity is due to a basic process controlled by the back-to-back Schottky barriers at grain boundaries with suitable thickness as well as the coexistence of phases.

An integration of minimum local feature representation methods to recognize large variation of foods

NASA Astrophysics Data System (ADS)

Razali, Mohd Norhisham bin; Manshor, Noridayu; Halin, Alfian Abdul; Mustapha, Norwati; Yaakob, Razali

2017-10-01

Local invariant features have shown to be successful in describing object appearances for image classification tasks. Such features are robust towards occlusion and clutter and are also invariant against scale and orientation changes. This makes them suitable for classification tasks with little inter-class similarity and large intra-class difference. In this paper, we propose an integrated representation of the Speeded-Up Robust Feature (SURF) and Scale Invariant Feature Transform (SIFT) descriptors, using late fusion strategy. The proposed representation is used for food recognition from a dataset of food images with complex appearance variations. The Bag of Features (BOF) approach is employed to enhance the discriminative ability of the local features. Firstly, the individual local features are extracted to construct two kinds of visual vocabularies, representing SURF and SIFT. The visual vocabularies are then concatenated and fed into a Linear Support Vector Machine (SVM) to classify the respective food categories. Experimental results demonstrate impressive overall recognition at 82.38% classification accuracy based on the challenging UEC-Food100 dataset.

A particle finite element method for machining simulations

NASA Astrophysics Data System (ADS)

Sabel, Matthias; Sator, Christian; Müller, Ralf

2014-07-01

The particle finite element method (PFEM) appears to be a convenient technique for machining simulations, since the geometry and topology of the problem can undergo severe changes. In this work, a short outline of the PFEM-algorithm is given, which is followed by a detailed description of the involved operations. The -shape method, which is used to track the topology, is explained and tested by a simple example. Also the kinematics and a suitable finite element formulation are introduced. To validate the method simple settings without topological changes are considered and compared to the standard finite element method for large deformations. To examine the performance of the method, when dealing with separating material, a tensile loading is applied to a notched plate. This investigation includes a numerical analysis of the different meshing parameters, and the numerical convergence is studied. With regard to the cutting simulation it is found that only a sufficiently large number of particles (and thus a rather fine finite element discretisation) leads to converged results of process parameters, such as the cutting force.

Common methods for fecal sample storage in field studies yield consistent signatures of individual identity in microbiome sequencing data.

PubMed

Blekhman, Ran; Tang, Karen; Archie, Elizabeth A; Barreiro, Luis B; Johnson, Zachary P; Wilson, Mark E; Kohn, Jordan; Yuan, Michael L; Gesquiere, Laurence; Grieneisen, Laura E; Tung, Jenny

2016-08-16

Field studies of wild vertebrates are frequently associated with extensive collections of banked fecal samples-unique resources for understanding ecological, behavioral, and phylogenetic effects on the gut microbiome. However, we do not understand whether sample storage methods confound the ability to investigate interindividual variation in gut microbiome profiles. Here, we extend previous work on storage methods for gut microbiome samples by comparing immediate freezing, the gold standard of preservation, to three methods commonly used in vertebrate field studies: lyophilization, storage in ethanol, and storage in RNAlater. We found that the signature of individual identity consistently outweighed storage effects: alpha diversity and beta diversity measures were significantly correlated across methods, and while samples often clustered by donor, they never clustered by storage method. Provided that all analyzed samples are stored the same way, banked fecal samples therefore appear highly suitable for investigating variation in gut microbiota. Our results open the door to a much-expanded perspective on variation in the gut microbiome across species and ecological contexts.

Confocal Laser Scanning Microscopy, a New In Vivo Diagnostic Tool for Schistosomiasis

PubMed Central

Holtfreter, Martha Charlotte; Nohr-Łuczak, Constanze; Guthoff, Rudolf Friedrich; Reisinger, Emil Christian

2012-01-01

Background The gold standard for the diagnosis of schistosomiasis is the detection of the parasite's characteristic eggs in urine, stool, or rectal and bladder biopsy specimens. Direct detection of eggs is difficult and not always possible in patients with low egg-shedding rates. Confocal laser scanning microscopy (CLSM) permits non-invasive cell imaging in vivo and is an established way of obtaining high-resolution images and 3-dimensional reconstructions. Recently, CLSM was shown to be a suitable method to visualize Schistosoma mansoni eggs within the mucosa of dissected mouse gut. In this case, we evaluated the suitability of CLSM to detect eggs of Schistosoma haematobium in a patient with urinary schistosomiasis and low egg-shedding rates. Methodology/Principal Findings The confocal laser scanning microscope used in this study was based on a scanning laser system for imaging the retina of a living eye, the Heidelberg Retina Tomograph II, in combination with a lens system (image modality). Standard light cystoscopy was performed using a rigid cystoscope under general anaesthesia. The CLSM endoscope was then passed through the working channel of the rigid cystoscope. The mucosal tissue of the bladder was scanned using CLSM. Schistoma haematobium eggs appeared as bright structures, with the characteristic egg shape and typical terminal spine. Conclusion/Significance We were able to detect schistosomal eggs in the urothelium of a patient with urinary schistosomiasis. Thus, CLSM may be a suitable tool for the diagnosis of schistosomiasis in humans, especially in cases where standard diagnostic tools are not suitable. PMID:22529947

Entropy stable high order discontinuous Galerkin methods for ideal compressible MHD on structured meshes

NASA Astrophysics Data System (ADS)

Liu, Yong; Shu, Chi-Wang; Zhang, Mengping

2018-02-01

We present a discontinuous Galerkin (DG) scheme with suitable quadrature rules [15] for ideal compressible magnetohydrodynamic (MHD) equations on structural meshes. The semi-discrete scheme is analyzed to be entropy stable by using the symmetrizable version of the equations as introduced by Godunov [32], the entropy stable DG framework with suitable quadrature rules [15], the entropy conservative flux in [14] inside each cell and the entropy dissipative approximate Godunov type numerical flux at cell interfaces to make the scheme entropy stable. The main difficulty in the generalization of the results in [15] is the appearance of the non-conservative "source terms" added in the modified MHD model introduced by Godunov [32], which do not exist in the general hyperbolic system studied in [15]. Special care must be taken to discretize these "source terms" adequately so that the resulting DG scheme satisfies entropy stability. Total variation diminishing / bounded (TVD/TVB) limiters and bound-preserving limiters are applied to control spurious oscillations. We demonstrate the accuracy and robustness of this new scheme on standard MHD examples.

Electro-optical properties of Cu2O for P excitons in the regime of Franz-Keldysh oscillations

NASA Astrophysics Data System (ADS)

Zielińska-Raczyńska, Sylwia; Ziemkiewicz, David; Czajkowski, Gerard

2018-04-01

We present the analytical method which enables one to compute the optical functions i.e., reflectivity, transmission, and absorption, including the excitonic effects, for a semiconductor crystal exposed to a uniform electric field for the energy region above the gap and for the external field suitable for the appearance of Franz-Keldysh (FK) oscillations. Our approach intrinsically takes into account the coherence between the carriers and the electromagnetic field. We quantitatively describe the amplitudes and periodicity of FK modulations as well as the influence of Rydberg excitons on the FK effect. Our analytical findings are illustrated numerically for P excitons in Cu2O crystal.

Theoretical analysis of compatibility of several reinforcement materials with NiAl and FeAl matrices

NASA Technical Reports Server (NTRS)

Misra, Ajay K.

1989-01-01

Several potential reinforcement materials were assessed for their chemical, coefficient of thermal expansion (CTE), and mechanical compatibility with the intermetallic matrices based on NiAl and FeAl. Among the ceramic reinforcement materials, Al2O3, TiC, and TiB2, appear to be the optimum choices for NiAl and FeAl matrices. However, the problem of CTE mismatch with the matrix needs to be solved for these three reinforcement materials. Beryllium-rich intermetallic compounds can be considered as potential reinforcement materials provided suitable reaction barrier coatings can be developed for these. Based on preliminary thermodynamic calculations, Sc2O3 and TiC appear to be suitable as reaction barrier coatings for the beryllides. Several reaction barrier coatings are also suggested for the currently available SiC fibers.

Spatial resolution and measurement uncertainty of strains in bone and bone-cement interface using digital volume correlation.

PubMed

Zhu, Ming-Liang; Zhang, Qing-Hang; Lupton, Colin; Tong, Jie

2016-04-01

The measurement uncertainty of strains has been assessed in a bone analogue (sawbone), bovine trabecular bone and bone-cement interface specimens under zero load using the Digital Volume Correlation (DVC) method. The effects of sub-volume size, sample constraint and preload on the measured strain uncertainty have been examined. There is generally a trade-off between the measurement uncertainty and the spatial resolution. Suitable sub-volume sizes have been be selected based on a compromise between the measurement uncertainty and the spatial resolution of the cases considered. A ratio of sub-volume size to a microstructure characteristic (Tb.Sp) was introduced to reflect a suitable spatial resolution, and the measurement uncertainty associated was assessed. Specifically, ratios between 1.6 and 4 appear to give rise to standard deviations in the measured strains between 166 and 620 με in all the cases considered, which would seem to suffice for strain analysis in pre as well as post yield loading regimes. A microscale finite element (μFE) model was built from the CT images of the sawbone, and the results from the μFE model and a continuum FE model were compared with those from the DVC. The strain results were found to differ significantly between the two methods at tissue level, consistent in trend with the results found in human bones, indicating mainly a limitation of the current DVC method in mapping strains at this level. Copyright © 2015 Elsevier Ltd. All rights reserved.

Validation and evaluation of measuring methods for the 3D documentation of external injuries in the field of forensic medicine.

PubMed

Buck, Ursula; Buße, Kirsten; Campana, Lorenzo; Schyma, Christian

2018-03-01

Three-dimensional (3D) measurement techniques are gaining importance in many areas. The latest developments brought more cost-effective, user-friendly, and faster technologies onto the market. Which 3D techniques are suitable in the field of forensic medicine and what are their advantages and disadvantages? This wide-ranging study evaluated and validated various 3D measurement techniques for the forensic requirements. High-tech methods as well as low-budget systems have been tested and compared in terms of accuracy, ease of use, expenditure of time, mobility, cost, necessary knowhow, and their limitations. Within this study, various commercial measuring systems of the different techniques were tested. Based on the first results, one measuring system was selected for each technique, which appeared to be the most suitable for the forensic application or is already established in forensic medicine. A body of a deceased, a face and an injury of a living person, and a shoe sole were recorded by 11 people with different professions and previous knowledge using the selected systems. The results were assessed and the personal experiences were evaluated using a questionnaire. In addition, precision investigations were carried out using test objects. The study shows that the hand-held scanner and photogrammetry are very suitable for the 3D documentation of forensic medical findings. Their moderate acquisition costs and easy operation could lead to more frequent application in forensic medicine in the future. For special applications, the stripe-light scanner still has its justification due to its high precision, the flexible application area, and the high reliability. The results show that, thanks to the technological advances, the 3D measurement technology will have more and more impact on the routine of the forensic medical examination.

Fracture characterization and fracture-permeability estimation at the underground research laboratory in southeastern Manitoba, Canada

USGS Publications Warehouse

Paillet, Frederick L.

1988-01-01

Various conventional geophysical well logs were obtained in conjunction with acoustic tube-wave amplitude and experimental heat-pulse flowmeter measurements in two deep boreholes in granitic rocks on the Canadian shield in southeastern Manitoba. The objective of this study is the development of measurement techniques and data processing methods for characterization of rock volumes that might be suitable for hosting a nuclear waste repository. One borehole, WRA1, intersected several major fracture zones, and was suitable for testing quantitative permeability estimation methods. The other borehole, URL13, appeared to intersect almost no permeable fractures; it was suitable for testing methods for the characterization of rocks of very small permeability and uniform thermo-mechanical properties in a potential repository horizon. Epithermal neutron , acoustic transit time, and single-point resistance logs provided useful, qualitative indications of fractures in the extensively fractured borehole, WRA1. A single-point log indicates both weathering and the degree of opening of a fracture-borehole intersection. All logs indicate the large intervals of mechanically and geochemically uniform, unfractured granite below depths of 300 m in the relatively unfractured borehole, URL13. Some indications of minor fracturing were identified in that borehole, with one possible fracture at a depth of about 914 m, producing a major acoustic waveform anomaly. Comparison of acoustic tube-wave attenuation with models of tube-wave attenuation in infinite fractures of given aperture provide permeability estimates ranging from equivalent single-fractured apertures of less than 0.01 mm to apertures of > 0.5 mm. One possible fracture anomaly in borehole URL13 at a depth of about 914 m corresponds with a thin mafic dike on the core where unusually large acoustic contrast may have produced the observed waveform anomaly. No indications of naturally occurring flow existed in borehole URL13; however, flowmeter measurements indicated flow at < 0.05 L/min from the upper fracture zones in borehole WRA1 to deeper fractures at depths below 800 m. (Author 's abstract)

Best teaching practices in anatomy education: A critical review.

PubMed

Estai, Mohamed; Bunt, Stuart

2016-11-01

In this report we review the range of teaching resources and strategies used in anatomy education with the aim of coming up with suggestions about the best teaching practices in this area. There is much debate about suitable methods of delivering anatomical knowledge. Competent clinicians, particularly surgeons, need a deep understanding of anatomy for safe clinical procedures. However, because students have had very limited exposure to anatomy during clinical training, there is a concern that medical students are ill-prepared in anatomy when entering clerkships and residency programs. Therefore, developing effective modalities for teaching anatomy is essential to safe medical practice. Cadaver-based instruction has survived as the main instructional tool for hundreds of years, however, there are differing views on whether full cadaver dissection is still appropriate for a modern undergraduate training. The limitations on curricular time, trained anatomy faculty and resources for gross anatomy courses in integrated or/and system-based curricula, have led many medical schools to abandon costly and time-consuming dissection-based instruction in favour of alternative methods of instruction including prosection, medical imaging, living anatomy and multimedia resources. To date, no single teaching tool has been found to meet curriculum requirements. The best way to teach modern anatomy is by combining multiple pedagogical resources to complement one another, students appear to learn more effectively when multimodal and system-based approaches are integrated. Our review suggests that certain professions would have more benefit from certain educational methods or strategies than others. Full body dissection would be best reserved for medical students, especially those with surgical career intentions, while teaching based on prosections and plastination is more suitable for dental, pharmacy and allied health science students. There is a need to direct future research towards evaluation of the suitability of the new teaching methodologies in new curricula and student perceptions of integrated and multimodal teaching paradigms, and the ability of these to satisfy learning outcomes. Copyright © 2016 Elsevier GmbH. All rights reserved.

Infrared and visible image fusion based on visual saliency map and weighted least square optimization

NASA Astrophysics Data System (ADS)

Ma, Jinlei; Zhou, Zhiqiang; Wang, Bo; Zong, Hua

2017-05-01

The goal of infrared (IR) and visible image fusion is to produce a more informative image for human observation or some other computer vision tasks. In this paper, we propose a novel multi-scale fusion method based on visual saliency map (VSM) and weighted least square (WLS) optimization, aiming to overcome some common deficiencies of conventional methods. Firstly, we introduce a multi-scale decomposition (MSD) using the rolling guidance filter (RGF) and Gaussian filter to decompose input images into base and detail layers. Compared with conventional MSDs, this MSD can achieve the unique property of preserving the information of specific scales and reducing halos near edges. Secondly, we argue that the base layers obtained by most MSDs would contain a certain amount of residual low-frequency information, which is important for controlling the contrast and overall visual appearance of the fused image, and the conventional "averaging" fusion scheme is unable to achieve desired effects. To address this problem, an improved VSM-based technique is proposed to fuse the base layers. Lastly, a novel WLS optimization scheme is proposed to fuse the detail layers. This optimization aims to transfer more visual details and less irrelevant IR details or noise into the fused image. As a result, the fused image details would appear more naturally and be suitable for human visual perception. Experimental results demonstrate that our method can achieve a superior performance compared with other fusion methods in both subjective and objective assessments.

Modeling and stress analysis of large format InSb focal plane arrays detector under thermal shock

NASA Astrophysics Data System (ADS)

Zhang, Li-Wen; Meng, Qing-Duan; Zhang, Xiao-Ling; Yu, Qian; Lv, Yan-Qiu; Si, Jun-Jie

2013-09-01

Higher fracture probability, appearing in large format InSb infrared focal plane arrays detector under thermal shock loadings, limits its applicability and suitability for large format equipment, and has been an urgent problem to be solved. In order to understand the fracture mechanism and improve the reliability, three dimensional modeling and stress analysis of large format InSb detector is necessary. However, there are few reports on three dimensional modeling and simulation of large format InSb detector, due to huge meshing numbers and time-consuming operation to solve. To solve the problems, basing on the thermal mismatch displacement formula, an equivalent modeling method is proposed in this paper. With the proposed equivalent modeling method, employing the ANSYS software, three dimensional large format InSb detector is modeled, and the maximum Von Mises stress appearing in InSb chip dependent on array format is researched. According to the maximum Von Mises stress location shift and stress increasing tendency, the adaptability range of the proposed equivalent method is also derived, that is, for 16 × 16, 32 × 32 and 64 × 64 format, its adaptability ranges are not larger than 64 × 64, 256 × 256 and 1024 × 1024 format, respectively. Taking 1024 × 1024 InSb detector as an example, the Von Mises stress distribution appearing in InSb chip, Si readout integrated circuits and indium bump arrays are described, and the causes are discussed in detail. All these will provide a feasible research plan to identify the fracture origins of InSb chip and reduce fracture probability for large format InSb detector.

20 CFR 327.15 - Reasonable efforts to obtain work.

Code of Federal Regulations, 2011 CFR

2011-04-01

... claimant. (b) Failure to comply with requirement. When the office of the Board which is adjudicating claims...) Responding to appropriate “want ads” for work which appears suitable for him; (5) Actively prosecuting his...

20 CFR 327.15 - Reasonable efforts to obtain work.

Code of Federal Regulations, 2012 CFR

2012-04-01

... claimant. (b) Failure to comply with requirement. When the office of the Board which is adjudicating claims...) Responding to appropriate “want ads” for work which appears suitable for him; (5) Actively prosecuting his...

20 CFR 327.15 - Reasonable efforts to obtain work.

Code of Federal Regulations, 2014 CFR

2014-04-01

... claimant. (b) Failure to comply with requirement. When the office of the Board which is adjudicating claims...) Responding to appropriate “want ads” for work which appears suitable for him; (5) Actively prosecuting his...

20 CFR 327.15 - Reasonable efforts to obtain work.

Code of Federal Regulations, 2013 CFR

2013-04-01

... claimant. (b) Failure to comply with requirement. When the office of the Board which is adjudicating claims...) Responding to appropriate “want ads” for work which appears suitable for him; (5) Actively prosecuting his...

20 CFR 327.15 - Reasonable efforts to obtain work.

Code of Federal Regulations, 2010 CFR

2010-04-01

... claimant. (b) Failure to comply with requirement. When the office of the Board which is adjudicating claims...) Responding to appropriate “want ads” for work which appears suitable for him; (5) Actively prosecuting his...

10 CFR 963.16 - Postclosure suitability evaluation method.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 963.16 Energy DEPARTMENT OF ENERGY YUCCA MOUNTAIN SITE SUITABILITY GUIDELINES Site Suitability... assessment to evaluate the ability of the Yucca Mountain disposal system to limit radiological doses and... the performance of the Yucca Mountain disposal system using the method described in paragraph (b) of...

Passive runaway electron suppression in tokamak disruptions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, H. M.; Helander, P.; Boozer, A. H.

2013-07-15

Runaway electrons created in disruptions pose a serious problem for tokamaks with large current. It would be desirable to have a runaway electron suppression method which is passive, i.e., a method that does not rely on an uncertain disruption prediction system. One option is to let the large electric field inherent in the disruption drive helical currents in the wall. This would create ergodic regions in the plasma and increase the runaway losses. Whether these regions appear at a suitable time and place to affect the formation of the runaway beam depends on disruption parameters, such as electron temperature andmore » density. We find that it is difficult to ergodize the central plasma before a beam of runaway current has formed. However, the ergodic outer region will make the Ohmic current profile contract, which can lead to instabilities that yield large runaway electron losses.« less

Development of Streptococcus agalactiae vaccines for tilapia.

PubMed

Liu, Guangjin; Zhu, Jielian; Chen, Kangming; Gao, Tingting; Yao, Huochun; Liu, Yongjie; Zhang, Wei; Lu, Chengping

2016-12-21

Vaccination is a widely accepted and effective method to prevent most pathogenic diseases in aquaculture. Various species of tilapia, especially Nile tilapia Oreochromis niloticus, are farmed worldwide because of their high consumer demand. Recently, the tilapia-breeding industry has been hampered by outbreaks of Streptococcus agalactiae infection, which cause high mortality and huge economic losses. Many researchers have attempted to develop effective S. agalactiae vaccines for tilapia. This review provides a summary of the different kinds of S. agalactiae vaccines for tilapia that have been developed recently. Among the various vaccine types, inactivated S. agalactiae vaccines showed superior protection efficiency when compared with live attenuated, recombinant and DNA vaccines. With respect to vaccination method, injecting the vaccine into tilapia provided the most effective immunoprotection. Freund's incomplete adjuvant appeared to be suitable for tilapia vaccines. Other factors, such as immunization duration and number, fish size and challenge dose, also influenced the vaccine efficacy.

Preparation of resveratrol-loaded nanoporous silica materials with different structures

NASA Astrophysics Data System (ADS)

Popova, Margarita; Szegedi, Agnes; Mavrodinova, Vesselina; Novak Tušar, Natasa; Mihály, Judith; Klébert, Szilvia; Benbassat, Niko; Yoncheva, Krassimira

2014-11-01

Solid, nanoporous silica-based spherical mesoporous MCM-41 and KIL-2 with interparticle mesoporosity as well as nanosized zeolite BEA materials differing in morphology and pore size distribution, were used as carriers for the preparation of resveratrol-loaded delivery systems. Two preparation methods have been applied: (i) loading by mixing of resveratrol and mesoporous carrier in solid state and (ii) deposition in ethanol solution. The parent and the resveratrol loaded carriers were characterized by XRD, TEM, N2 physisorption, thermal analysis, and FT-IR spectroscopy. The influence of the support structure on the adsorption capacity and the release kinetics of this poorly soluble compound were investigated. Our results indicated that the chosen nanoporous silica supports are suitable for stabilization of trans-resveratrol and reveal controlled release and ability to protect the supported compound against degradation regardless of loading method. The solid-state dry mixing appears very effective for preparation of drug formulations composed of poorly soluble compound.

Review on Rapid Seismic Vulnerability Assessment for Bulk of Buildings

NASA Astrophysics Data System (ADS)

Nanda, R. P.; Majhi, D. R.

2013-09-01

This paper provides a brief overview of rapid visual screening (RVS) procedures available in different countries with a comparison among all the methods. Seismic evaluation guidelines from, USA, Canada, Japan, New Zealand, India, Europe, Italy, UNDP, with other methods are reviewed from the perspective of their applicability to developing countries. The review shows clearly that some of the RVS procedures are unsuited for potential use in developing countries. It is expected that this comparative assessment of various evaluation schemes will help to identify the most essential components of such a procedure for use in India and other developing countries, which is not only robust, reliable but also easy to use with available resources. It appears that Federal Emergency Management Agency (FEMA) 154 and New Zealand Draft Code approaches can be suitably combined to develop a transparent, reasonably rigorous and generalized procedure for seismic evaluation of buildings in developing countries.

Drawing a different picture with pencil lead as matrix-assisted laser desorption/ionization matrix for fullerene derivatives.

PubMed

Nye, Leanne C; Hungerbühler, Hartmut; Drewello, Thomas

2018-02-01

Inspired by reports on the use of pencil lead as a matrix-assisted laser desorption/ionization matrix, paving the way towards matrix-free matrix-assisted laser desorption/ionization, the present investigation evaluates its usage with organic fullerene derivatives. Currently, this class of compounds is best analysed using the electron transfer matrix trans-2-[3-(4-tert-butylphenyl)-2-methyl-2-propenylidene] malononitrile (DCTB), which was employed as the standard here. The suitability of pencil lead was additionally compared to direct (i.e. no matrix) laser desorption/ionization-mass spectrometry. The use of (DCTB) was identified as the by far gentler method, producing spectra with abundant molecular ion signals and much reduced fragmentation. Analytically, pencil lead was found to be ineffective as a matrix, however, appears to be an extremely easy and inexpensive method for producing sodium and potassium adducts.

Saccadic eye movements analysis as a measure of drug effect on central nervous system function.

PubMed

Tedeschi, G; Quattrone, A; Bonavita, V

1986-04-01

Peak velocity (PSV) and duration (SD) of horizontal saccadic eye movements are demonstrably under the control of specific brain stem structures. Experimental and clinical evidence suggest the existence of an immediate premotor system for saccade generation located in the paramedian pontine reticular formation (PPRF). Effects on saccadic eye movements have been studied in normal volunteers with barbiturates, benzodiazepines, amphetamine and ethanol. On two occasions computer analysis of PSV, SD, saccade reaction time (SRT) and saccade accuracy (SA) was carried out in comparison with more traditional methods of assessment of human psychomotor performance like choice reaction time (CRT) and critical flicker fusion threshold (CFFT). The computer system proved to be a highly sensitive and objective method for measuring drug effect on central nervous system (CNS) function. It allows almost continuous sampling of data and appears to be particularly suitable for studying rapidly changing drug effects on the CNS.

A physically based catchment partitioning method for hydrological analysis

NASA Astrophysics Data System (ADS)

Menduni, Giovanni; Riboni, Vittoria

2000-07-01

We propose a partitioning method for the topographic surface, which is particularly suitable for hydrological distributed modelling and shallow-landslide distributed modelling. The model provides variable mesh size and appears to be a natural evolution of contour-based digital terrain models. The proposed method allows the drainage network to be derived from the contour lines. The single channels are calculated via a search for the steepest downslope lines. Then, for each network node, the contributing area is determined by means of a search for both steepest upslope and downslope lines. This leads to the basin being partitioned into physically based finite elements delimited by irregular polygons. In particular, the distributed computation of local geomorphological parameters (i.e. aspect, average slope and elevation, main stream length, concentration time, etc.) can be performed easily for each single element. The contributing area system, together with the information on the distribution of geomorphological parameters provide a useful tool for distributed hydrological modelling and simulation of environmental processes such as erosion, sediment transport and shallow landslides.

16 CFR 1508.9 - Identifying marks, warning statement, and compliance declaration.

Code of Federal Regulations, 2011 CFR

2011-01-01

... shall appear in block letters, shall contrast sharply with the background (by color, projection, and/or... affixed, fastened, or attached thereto by means of a tag, token, or other suitable medium. The markings...

The Effect of deposition rate on FePt/MgO crystal orientation

NASA Astrophysics Data System (ADS)

Sheikhi, M.; Sebt, S. A.; Khajehnezhad, A.

2018-06-01

FePt granular layers which are made in suitable conditions can have three types of ordering that are crystalline, compositional orders and directional configuration of nanoparticles. Formation of fct structure with L10 compositional ordering requires high temperature. At this temperature, a problem is the size control of the nanoparticles and another problem is control of their crystal orientation. Fabrication method and the use of suitable substrates can help solving these problems. In direct synthesis by sputtering method on the warm substrate the size of FePt nanoparticles in L10 compositional ordered phase can be controlled. We show that crystal orientation of L10-FePt nanoparticles on a thin layer of MgO depends on the rate of deposition. This becomes clear from the results of the XRD analyses of samples. Based on these results in synthesis at room temperature with deposition rate of upper than 1.5 Å/s after annealing, (001) peak is dominated and at rate of lower than 1.0 Å/s just (111) peak is appeared. In direct synthesis with intermediate rate (111) and (110) peaks can be seen. Moreover, the difference of the shape of hysteresis loops of samples in parallel and vertical directions are the witnesses for orientation of samples in presence of MgO layer and the effect of FePt deposition rate on it.

Effects of advanced selection methods on sperm quality and ART outcome.

PubMed

Yetunde, I; Vasiliki, M

2013-10-01

In assisted reproductive technology (ART), the role of spermatozoa has evolved over the years. In the past, early methods of selecting sperm for ART only focused on selecting motile and morphologically normal appearing sperm. It has become evident that these methods are inefficient in identifying the most suitable sperm for fertilization. Novel methods have thus been created to identify highly motile, morphologically normal, viable non-apoptotic spermatozoa with intact membranes and high DNA integrity for use in ART. These advanced methods of selection utilize our knowledge of unique characteristics of sperm, such as sperm surface charge, the presence of hyaluronic acid binding sites on sperm, sperm ultramorphology, markers of apoptosis and zona pellucida binding on sperm. These methods have shown potential promise in improving ART outcomes. Future developments may include Raman spectroscopy, confocal light absorption and scattering spectroscopic microscopy, and polarization microscopy. While these novel techniques have potential, they come with a cost burden and further studies are required to demonstrate their impact on ART outcomes. Furthermore, clinicians and human reproductive scientists need to continue to gather knowledge about human fertilization and determine the most physiological methods of sperm selection.

In situ mineralogical-chemical analysis of Martian materials at landing/roving sites by active and passive remote sensing methods

NASA Technical Reports Server (NTRS)

Neukum, G.; Lehmann, F.; Regner, P.; Jaumann, R.

1988-01-01

Remote sensing of the Martian surface from the ground and from orbiting spacecraft has provided some first-order insight into the mineralogical-chemical composition and the weathering state of Martian surface materials. Much more detailed information can be gathered from performing such measurements in situ at the landing sites or from a rover in combination with analogous measurements from orbit. Measurements in the wavelength range of approximately 0.3 to 12.0 micrometers appear to be suitable to characterize much of the physical, mineralogical, petrological, and chemical properties of Martian surface materials and the weathering and other alteration processes that have acted on them. It is of particular importance to carry out measurements at the same time over a broad wavelength range since the reflectance signatures are caused by different effects and hence give different and complementing information. It appears particularly useful to employ a combination of active and passive methods because the use of active laser spectroscopy allows the obtaining of specific information on thermal infrared reflectance of surface materials. It seems to be evident that a spectrometric survey of Martian materials has to be focused on the analysis of altered and fresh mafic materials and rocks, water-bearing silicates, and possibly carbonates.

Assessing the risk zones of Chagas' disease in Chile, in a world marked by global climatic change

PubMed Central

Tapia-Garay, Valentina; Figueroa, Daniela P; Maldonado, Ana; Frías-Laserre, Daniel; Gonzalez, Christian R; Parra, Alonso; Canals, Lucia; Apt, Werner; Alvarado, Sergio; Cáceres, Dante; Canals, Mauricio

2018-01-01

BACKGROUND Vector transmission of Trypanosoma cruzi appears to be interrupted in Chile; however, data show increasing incidence of Chagas' disease, raising concerns that there may be a reemerging problem. OBJECTIVE To estimate the actual risk in a changing world it is necessary to consider the historical vector distribution and correlate this distribution with the presence of cases and climate change. METHODS Potential distribution models of Triatoma infestans and Chagas disease were performed using Maxent, a machine-learning method. FINDINGS Climate change appears to play a major role in the reemergence of Chagas' disease and T. infestans in Chile. The distribution of both T. infestans and Chagas' disease correlated with maximum temperature, and the precipitation during the driest month. The overlap of Chagas' disease and T. infestans distribution areas was high. The distribution of T. infestans, under two global change scenarios, showed a minimal reduction tendency in suitable areas. MAIN CONCLUSION The impact of temperature and precipitation on the distribution of T. infestans, as shown by the models, indicates the need for aggressive control efforts; the current control measures, including T. infestans control campaigns, should be maintained with the same intensity as they have at present, avoiding sylvatic foci, intrusions, and recolonisation of human dwellings. PMID:29211105

Integrating ethics in health technology assessment: many ways to Rome.

PubMed

Hofmann, Björn; Oortwijn, Wija; Bakke Lysdahl, Kristin; Refolo, Pietro; Sacchini, Dario; van der Wilt, Gert Jan; Gerhardus, Ansgar

2015-01-01

The aim of this study was to identify and discuss appropriate approaches to integrate ethical inquiry in health technology assessment (HTA). The key question is how ethics can be integrated in HTA. This is addressed in two steps: by investigating what it means to integrate ethics in HTA, and by assessing how suitable the various methods in ethics are to be integrated in HTA according to these meanings of integration. In the first step, we found that integrating ethics can mean that ethics is (a) subsumed under or (b) combined with other parts of the HTA process; that it can be (c) coordinated with other parts; or that (d) ethics actively interacts and changes other parts of the HTA process. For the second step, we found that the various methods in ethics have different merits with respect to the four conceptions of integration in HTA. Traditional approaches in moral philosophy tend to be most suited to be subsumed or combined, while processual approaches being close to the HTA or implementation process appear to be most suited to coordinated and interactive types of integration. The article provides a guide for choosing the ethics approach that appears most appropriate for the goals and process of a particular HTA.

Phased Restoration Plan for Degraded Land in North Korea by the Clustered Distribution Pattern of Suitable Afforestation Plants

NASA Astrophysics Data System (ADS)

Lee, S. G.; Lee, W. K.; Choi, H. A.; Yoo, H.; Song, C.; Son, Y.; Cha, S.; Bae, S. W.

2017-12-01

Degraded forest of North Korea (DPRK; The Democratic People's Republic of Koprea) is not only confined itself, it could cause serious problem in Korean Peninsula. The importance of restoration for degraded land has increased to improve an healthy ecosystem and solve a shortage of food in North Korea lately. On the other hand, although effort of North Korea government, degraded problem have consistently got worse. There are two main reasons it does not show effectively. The most critical one is absence of technique and information to restore, they concentrate urgent problem which is related to a poor food supply. The other problem is that they demand an efficiency plan in a short period. In these aspect, this study aims selecting suitable tree by spatial characteristics and establishing phased restoration plan to support policy decision about a degraded land in North Korea. The suitable tree for restoration is taken from references which involve natural plant distribution of North and South Korea (ROK; Republic of Korea). Optimal environmental predicted map is deducted from accumulated data of plant physiology whose endemic environmental optimal range individually. It is integrated a map by order of priorities that first is suitable tree species according to the region, and second is clustering distribution rate in a same species. The two types of priority is applied to weighting method. The research result shows that 23 afforestation species fit to restore, and lager distributed plants agree with the major species in Korean Peninsula. The integrated map considers weight of priorities, and it appears that Picea jezoensis is matched the widest. The integrated map shows a view of suitable restoration according to the space, but this is finespun to utilize in a policy. Therefore It provides 3 step plan to support policy decision by Block Statistics, as 12.5km (long-term general plan), 5km (medium-term detailed plan), 1km (short-term implementation plan).

Axillary Temperature, as Recorded by the iThermonitor WT701, Well Represents Core Temperature in Adults Having Noncardiac Surgery.

PubMed

Pei, Lijian; Huang, Yuguang; Mao, Guangmei; Sessler, Daniel I

2018-03-01

Core temperature can be accurately measured from the esophagus or nasopharynx during general anesthesia, but neither site is suitable for neuraxial anesthesia. We therefore determined the precision and accuracy of a novel wireless axillary thermometer, the iThermonitor, to determine its suitability for use during neuraxial anesthesia and in other patients who are not intubated. We enrolled 80 adults having upper abdominal surgery with endotracheal intubation. Intraoperative core temperature was measured in distal esophagus and was estimated at the axilla with a wireless iThermonitor WT701 (Raiing Medical, Boston MA) at 5-minute intervals. Pairs of axillary and reference distal esophageal temperatures were compared and summarized using linear regression and repeated-measured Bland-Altman methods. We a priori determined that the iThermonitor would have clinically acceptable accuracy if most estimates were within ±0.5°C of the esophageal reference, and suitable precision if the limits of agreement were within ±0.5°C. There were 3339 sets of paired temperatures. Axillary and esophageal temperatures were similar, with a mean difference (esophageal minus axillary) of only 0.14°C ± 0.26°C (standard deviation). The Bland-Altman 95% limits of agreement were reasonably narrow, with the estimated upper limit at 0.66°C and the lower limit at -0.38°C, thus ±0.52°C, indicating good agreement across the range of mean temperatures from 34.9°C to 38.1°C. The absolute difference was within 0.5°C in 91% of the measurements (95% confidence interval, 88%-93%). Axillary temperature, as recorded by the iThermonitor WT701, well represents core temperature in adults having noncardiac surgery and thus appears suitable for clinical use.

Development of europium doped BaSO4 TL OSL dual phosphor for radiation dosimetry applications

NASA Astrophysics Data System (ADS)

Patle, Anita; Patil, R. R.; Kulkarni, M. S.; Bhatt, B. C.; Moharil, S. V.

2015-08-01

This paper presents the results on the preparation and characterization of Europium-doped Barium sulfate (BaSO4: Eu) TL /OSL dual phosphor. The OSL sensitivity was found to be 11% of the commercially available Al2O3: C, using area integration method. The sample also shows good TL sensitivity and the dosimetric peak appears around 190°C with a shoulder at 282°C. After OSL readout, No change in the TL glow curve is observed. Since the observed TL peaks are not responsible for the observed OSL, good OSL as well as TL sensitivity and low fading will make this phosphor suitable for applications in radiation dosimetry using OSL as well as TL.

16 CFR 1509.11 - Identifying marks, caution statement, and compliance declaration.

Code of Federal Regulations, 2011 CFR

2011-01-01

... shall appear in block letters, shall contrast sharply with the background (by color, projection, and/or..., fastened, or attached thereto by means of a tag, token, or other suitable medium. The markings shall not be...

16 CFR 1509.11 - Identifying marks, caution statement, and compliance declaration.

Code of Federal Regulations, 2010 CFR

2010-01-01

... shall appear in block letters, shall contrast sharply with the background (by color, projection, and/or..., fastened, or attached thereto by means of a tag, token, or other suitable medium. The markings shall not be...

Proximal sensing for soil carbon accounting

NASA Astrophysics Data System (ADS)

England, Jacqueline R.; Viscarra Rossel, Raphael A.

2018-05-01

Maintaining or increasing soil organic carbon (C) is vital for securing food production and for mitigating greenhouse gas (GHG) emissions, climate change, and land degradation. Some land management practices in cropping, grazing, horticultural, and mixed farming systems can be used to increase organic C in soil, but to assess their effectiveness, we need accurate and cost-efficient methods for measuring and monitoring the change. To determine the stock of organic C in soil, one requires measurements of soil organic C concentration, bulk density, and gravel content, but using conventional laboratory-based analytical methods is expensive. Our aim here is to review the current state of proximal sensing for the development of new soil C accounting methods for emissions reporting and in emissions reduction schemes. We evaluated sensing techniques in terms of their rapidity, cost, accuracy, safety, readiness, and their state of development. The most suitable method for measuring soil organic C concentrations appears to be visible-near-infrared (vis-NIR) spectroscopy and, for bulk density, active gamma-ray attenuation. Sensors for measuring gravel have not been developed, but an interim solution with rapid wet sieving and automated measurement appears useful. Field-deployable, multi-sensor systems are needed for cost-efficient soil C accounting. Proximal sensing can be used for soil organic C accounting, but the methods need to be standardized and procedural guidelines need to be developed to ensure proficient measurement and accurate reporting and verification. These are particularly important if the schemes use financial incentives for landholders to adopt management practices to sequester soil organic C. We list and discuss requirements for developing new soil C accounting methods based on proximal sensing, including requirements for recording, verification, and auditing.

Simultaneous determination of vitamins A and D3 in dairy products by liquid chromatography-tandem mass spectrometry (LC-MS/MS)

NASA Astrophysics Data System (ADS)

Barakat, I. S. A.; Hammouri, M. K.; Habib, I.

2015-10-01

A potential method for simultaneous determination of vitamin A and vitamin D3 (25- hydroxyvitamin D3) in fresh milk samples is addressed. The method is based on combination of high performance liquid chromatography and mass spectrometry during the course of analysis. The method applied for determination of vitamins A and D3 on eighteen (18) different fresh milk samples using liquid chromatography along with tandem -mass spectrometry. The work describes the suitability of the proposed method for the simultaneous determination of both vitamins using LC-MS/MS as a specific and quantitative technique. The vitamins of milk were separated by C18 Thermo gold column(100mm × 4.6mm × 5 μm) with a flow rate of 1ml/min (using an isocratic mobile phase). The method was validated using duplicate analyses, relative recovery experiment, and comparative analysis with control samples. Liquid- liquid extraction was employed as a pre-concentration step with n-hexane - dichloromethane mixture (90%:10%) as an extraction solvent. The molecular ions (m/z) appeared near 286 and 385nm and for the base peaks were appeared near 255 and 355nm for vitamins A and D3. Good correlation coefficients were obtained, 0.9999 for vitamin D3 and 0.9994 for vitamin A. The limit of detection and the limit of quantification were found to be 0.09ng/ml and 0.54ng/ml for vitamin D3 and 0.32ng/ml and 1.8ng/ml and for vitamin A. The proposed method showed excellent recoveries, about 98% for both vitamins A and D3.

Determining the most suitable areas for artificial groundwater recharge via an integrated PROMETHEE II-AHP method in GIS environment (case study: Garabaygan Basin, Iran).

PubMed

Nasiri, Hossein; Boloorani, Ali Darvishi; Sabokbar, Hassan Ali Faraji; Jafari, Hamid Reza; Hamzeh, Mohamad; Rafii, Yusef

2013-01-01

Flood spreading is a suitable strategy for controlling and benefiting from floods. Selecting suitable areas for flood spreading and directing the floodwater into permeable formations are amongst the most effective strategies in flood spreading projects. Having combined geographic information systems (GIS) and multi-criteria decision analysis approaches, the present study sought to locate the most suitable areas for flood spreading operation in the Garabaygan Basin of Iran. To this end, the data layers relating to the eight effective factors were prepared in GIS environment. This stage was followed by elimination of the exclusionary areas for flood spreading while determining the potentially suitable ones. Having closely examined the potentially suitable areas using the Preference Ranking Organization Method for Enrichment Evaluations (PROMETHEE) II and analytic hierarchy process (AHP) methods, the land suitability map for flood spreading was produced. The PROMETHEE II and AHP were used for ranking all the alternatives and weighting the criteria involved, respectively. The results of the study showed that most suitable areas for the artificial groundwater recharge are located in Quaternary Q(g) and Q(gsc) geologic units and in geomorphological units of pediment and Alluvial fans with slopes not exceeding 3%. Furthermore, significant correspondence between the produced map and the control areas, where the flood spreading projects were successfully performed, provided further evidence for the acceptable efficiency of the integrated PROMETHEE II-AHP method in locating suitable flood spreading areas.

Applying Activity Based Costing (ABC) Method to Calculate Cost Price in Hospital and Remedy Services

PubMed Central

Rajabi, A; Dabiri, A

2012-01-01

Background Activity Based Costing (ABC) is one of the new methods began appearing as a costing methodology in the 1990’s. It calculates cost price by determining the usage of resources. In this study, ABC method was used for calculating cost price of remedial services in hospitals. Methods: To apply ABC method, Shahid Faghihi Hospital was selected. First, hospital units were divided into three main departments: administrative, diagnostic, and hospitalized. Second, activity centers were defined by the activity analysis method. Third, costs of administrative activity centers were allocated into diagnostic and operational departments based on the cost driver. Finally, with regard to the usage of cost objectives from services of activity centers, the cost price of medical services was calculated. Results: The cost price from ABC method significantly differs from tariff method. In addition, high amount of indirect costs in the hospital indicates that capacities of resources are not used properly. Conclusion: Cost price of remedial services with tariff method is not properly calculated when compared with ABC method. ABC calculates cost price by applying suitable mechanisms but tariff method is based on the fixed price. In addition, ABC represents useful information about the amount and combination of cost price services. PMID:23113171

A simple quasi-diabatization scheme suitable for spectroscopic problems based on one-electron properties of interacting states

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cave, Robert J., E-mail: Robert-Cave@hmc.edu; Stanton, John F., E-mail: JFStanton@gmail.com

We present a simple quasi-diabatization scheme applicable to spectroscopic studies that can be applied using any wavefunction for which one-electron properties and transition properties can be calculated. The method is based on rotation of a pair (or set) of adiabatic states to minimize the difference between the given transition property at a reference geometry of high symmetry (where the quasi-diabatic states and adiabatic states coincide) and points of lower symmetry where quasi-diabatic quantities are desired. Compared to other quasi-diabatization techniques, the method requires no special coding, facilitates direct comparison between quasi-diabatic quantities calculated using different types of wavefunctions, and ismore » free of any selection of configurations in the definition of the quasi-diabatic states. On the other hand, the method appears to be sensitive to multi-state issues, unlike recent methods we have developed that use a configurational definition of quasi-diabatic states. Results are presented and compared with two other recently developed quasi-diabatization techniques.« less

A flow calorimeter for determining combustion efficiency from residual enthalpy of exhaust gases

NASA Technical Reports Server (NTRS)

Evans, Albert; Hibbard, Robert R

1954-01-01

A flow calorimeter for determining the combustion efficiency of turbojet and ram-jet combustors from measurement of the residual enthalpy of combustion of the exhaust gas is described. Briefly, the calorimeter catalytically oxidizes the combustible constituents of exhaust-gas samples, and the resultant temperature rise is measured. This temperature rise is related to the residual enthalpy of combustion of the sample by previous calibration of the calorimeter. Combustion efficiency can be calculated from a knowledge of the residual enthalpy of the exhaust gas and the combustor input enthalpy. An accuracy of +-0.2 Btu per cubic foot was obtained with prepared fuel-air mixtures, and the combustion efficiencies of single turbojet combustors measured by both the flow-calorimeter and heat-balance methods compared within 3 percentage units. Flow calorimetry appears to be a suitable method for determining combustion efficiencies at high combustor temperatures where ordinary thermocouples cannot be used. The method is fundamentally more accurate than heat-balance methods at high combustion efficiencies and can be used to verify near-100-percent efficiency data.

Methods for determination of low-molecular weight carbonyl compounds in the ambient atmosphere

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vairavamurthy, A.; Roberts, J.M.; Newman, L.

1991-01-01

Determination of carbonyl compounds in the ambient atmosphere is receiving increasing attention because of the critical role these compounds play in tropospheric organic chemistry. Currently, field measurements are very limited mainly because of the analytical challenges posed by trace concentrations and interferences arising from atmospheric copollutants. We review here the methods for used for determination of carbonyl compounds, from an atmospheric chemistry perspective, emphasizing the principles, advantages, and limitations. Since a large number of varied types of methods have been used specifically for determination of formaldehyde, it is considered separately from other carbonyls. It is clear that despite more thanmore » a decade of work, many problems related to sampling, interferences, and artifacts have not been resolved. Because of the increasing demand for time-series measurements in field studies, and automated method for continuous sampling and analysis of carbonyls is very much required. The widely used liquid chromatographic method based on 2,4-dinitrophenylhydrazine derivatization appears unsuitable for this purpose because of the lengthy collection times required to achieve sub-ppbv detection limits. Important issues to be considered in the development of a suitable field method and potential approaches are discussed. 155 refs., 19 figs., 5 tabs.« less

Estimation of stereovision in conditions of blurring simulation

NASA Astrophysics Data System (ADS)

Krumina, Gunta; Ozolinsh, Maris; Lacis, Ivazs; Lyakhovetskii, Vsevolod

2005-08-01

The aim of this study was to evaluate the simulation of eye pathologies, such as amblyopia and cataracts, to estimate the stereovision in artificial conditions, and to compare the results on the stereothreshold obtained in artificial and real- pathologic conditions. Characteristic of the above-mentioned real-life forms of a reduced vision is a blurred image in one of the eyes. The blurring was simulated by (i) defocusing, (ii) blurred stimuli on the screen, and (iii) occluding of an eye with PLZT or PDLC plates. When comparing the methods, two parameters were used: the subject's visual acuity and the modulation depth of the image. The eye occluder method appeared to systematically provide higher stereothreshold values than the rest of the methods. The PLZT and PDLC plates scattered more in the blue and decreased the contrast of the stimuli when the blurring degree was increased. In the eye occluder method, the stereothreshold increased faster than in the defocusation and monitor stimuli methods when the visual acuity difference was higher than 0.4. It has been shown that the PLZT and PDLC plates are good optical phantoms for the simulation of a cataract, while the defocusation and monitor stimuli methods are more suitable for amblyopia.

Effectiveness of recommended euthanasia methods in larval zebrafish (Danio rerio).

PubMed

Strykowski, Jennifer L; Schech, Joseph M

2015-01-01

The popularity of zebrafish and its use as a model organism in biomedical research including genetics, development, and toxicology, has increased over the past 20 y and continues to grow. However, guidelines for euthanasia remain vague, and the responsibility of creating appropriate euthanasia protocols essentially falls on individual facilities. To reduce variation in experimental results among labs, a standard method of euthanasia for zebrafish would be useful. Although various euthanasia methods have been compared, few studies focus on the effectiveness of euthanasia methods for larval zebrafish. In this study, we exposed larval zebrafish to each of 3 euthanasia agents (MS222, eugenol, and hypothermic shock) and assessed the recovery rate. Hypothermic shock appeared to be the most effective method for euthanizing zebrafish at 14 d after fertilization; however, this method may not be considered an efficient method for large numbers of larval zebrafish. Exposure to chemicals, such as MS222 and eugenol, were ineffective methods for euthanasia at this stage of development. When these agents are used, secondary measures should be taken to ensure death. Choosing a euthanasia method that is effective, efficient, and humane can be challenging. Determining a method of euthanasia that is suitable for fish of all stages will bring the zebrafish community closer to meeting this challenge.

Effectiveness of Recommended Euthanasia Methods in Larval Zebrafish (Danio rerio)

PubMed Central

Strykowski, Jennifer L; Schech, Joseph M

2015-01-01

The popularity of zebrafish and its use as a model organism in biomedical research including genetics, development, and toxicology, has increased over the past 20 y and continues to grow. However, guidelines for euthanasia remain vague, and the responsibility of creating appropriate euthanasia protocols essentially falls on individual facilities. To reduce variation in experimental results among labs, a standard method of euthanasia for zebrafish would be useful. Although various euthanasia methods have been compared, few studies focus on the effectiveness of euthanasia methods for larval zebrafish. In this study, we exposed larval zebrafish to each of 3 euthanasia agents (MS222, eugenol, and hypothermic shock) and assessed the recovery rate. Hypothermic shock appeared to be the most effective method for euthanizing zebrafish at 14 d after fertilization; however, this method may not be considered an efficient method for large numbers of larval zebrafish. Exposure to chemicals, such as MS222 and eugenol, were ineffective methods for euthanasia at this stage of development. When these agents are used, secondary measures should be taken to ensure death. Choosing a euthanasia method that is effective, efficient, and humane can be challenging. Determining a method of euthanasia that is suitable for fish of all stages will bring the zebrafish community closer to meeting this challenge. PMID:25651096

[Climate suitability for tea growing in Zhejiang Province].

PubMed

Jin, Zhi-Feng; Ye, Jian-Gang; Yang, Zai-Qiang; Sun, Rui; Hu, Bo; Li, Ren-Zhong

2014-04-01

It is important to quantitatively assess the climate suitability of tea and its response to climate change. Based on meteorological indices of tea growth and daily meteorological data from 1971 to 2010 in Zhejiang Province, three climate suitability models for single climate factors, including temperature, precipitation and sunshine, were established at a 10-day scale by using the fuzzy mathematics method, and a comprehensive climate suitability model was established with the geometric average method. The results indicated that the climate suitability was high in the tea growth season in Zhejiang Province, and the three kinds of climate suitability were all higher than 0.6. As for the single factor climate suitability, temperature suitability was the highest and sunshine suitability was the lowest. There were obvious inter-annual variations of tea climate suitability, with a decline trend in the 1970s, less variation in the 1980s, and an obvious incline trend after the 1990s. The change tendency of climate suitability for spring tea was similar with that of annual climate suitability, lower in the 1980s, higher in the 1970s and after the 1990s. However, the variation amplitude of the climate suitability for spring tea was larger. The climate suitability for summer tea and autumn tea showed a decline trend from 1971 to 2010.

Analysis of free breathing motion using artifact reduced 4D CT image data

NASA Astrophysics Data System (ADS)

Ehrhardt, Jan; Werner, Rene; Frenzel, Thorsten; Lu, Wei; Low, Daniel; Handels, Heinz

2007-03-01

The mobility of lung tumors during the respiratory cycle is a source of error in radiotherapy treatment planning. Spatiotemporal CT data sets can be used for studying the motion of lung tumors and inner organs during the breathing cycle. We present methods for the analysis of respiratory motion using 4D CT data in high temporal resolution. An optical flow based reconstruction method was used to generate artifact-reduced 4D CT data sets of lung cancer patients. The reconstructed 4D CT data sets were segmented and the respiratory motion of tumors and inner organs was analyzed. A non-linear registration algorithm is used to calculate the velocity field between consecutive time frames of the 4D data. The resulting velocity field is used to analyze trajectories of landmarks and surface points. By this technique, the maximum displacement of any surface point is calculated, and regions with large respiratory motion are marked. To describe the tumor mobility the motion of the lung tumor center in three orthogonal directions is displayed. Estimated 3D appearance probabilities visualize the movement of the tumor during the respiratory cycle in one static image. Furthermore, correlations between trajectories of the skin surface and the trajectory of the tumor center are determined and skin regions are identified which are suitable for prediction of the internal tumor motion. The results of the motion analysis indicate that the described methods are suitable to gain insight into the spatiotemporal behavior of anatomical and pathological structures during the respiratory cycle.

Habitat suitability and movement corridors of grey wolf (Canis lupus) in Northern Pakistan.

PubMed

Kabir, Muhammad; Hameed, Shoaib; Ali, Hussain; Bosso, Luciano; Din, Jaffar Ud; Bischof, Richard; Redpath, Steve; Nawaz, Muhammad Ali

2017-01-01

Habitat suitability models are useful to understand species distribution and to guide management and conservation strategies. The grey wolf (Canis lupus) has been extirpated from most of its historic range in Pakistan primarily due to its impact on livestock and livelihoods. We used non-invasive survey data from camera traps and genetic sampling to develop a habitat suitability model for C. lupus in northern Pakistan and to explore the extent of connectivity among populations. We detected suitable habitat of grey wolf using a maximum entropy approach (Maxent ver. 3.4.0) and identified suitable movement corridors using the Circuitscape 4.0 tool. Our model showed high levels of predictive performances, as seen from the values of area under curve (0.971±0.002) and true skill statistics (0.886±0.021). The main predictors for habitat suitability for C. lupus were distances to road, mean temperature of the wettest quarter and distance to river. The model predicted ca. 23,129 km2 of suitable areas for wolf in Pakistan, with much of suitable habitat in remote and inaccessible areas that appeared to be well connected through vulnerable movement corridors. These movement corridors suggest that potentially the wolf range can expand in Pakistan's Northern Areas. However, managing protected areas with stringent restrictions is challenging in northern Pakistan, in part due to heavy dependence of people on natural resources. The habitat suitability map provided by this study can inform future management strategies by helping authorities to identify key conservation areas.

[Evaluation of metabolic rate for a correct risk assessment of thermal environments].

PubMed

Del Ferraro, Simona; Molinaro, V

2010-01-01

The new law n.81/2008 recognises microclimate as one of physical agents for which risk assessment becomes obligatory. To achieve this it is necessary to evaluate suitable indices, based on heat balance equation, which depend on six parameters: the first four are related to thermal environment and the last two are related to the worker (metabolic rate and thermal insulation). The first four parameters are directly measurable in situ by using a multiple data acquisition unit provided with suitable sensors. Parameters related to the worker are not directly measurable. This aspect represents one of the problems which can lead to an inaccurate risk assessment. Aim of the paper was to identify a method which leads to a correct evaluation of the metabolic rate related to the worker under study. It was decided to follow the procedures described by the standard UNI EN ISO 8996:2005 which presents four different levels to evaluate metabolic rate, each one with an increasing degree of accuracy. Seven workers were selected: three performed light tasks and the other four did heavy work. The study showed that the results appear to be in acceptable agreement in the case of light work while there were detectable differences in value for heavy tasks. The Authors believe it is necessary to stress the importance of a suitable estimation of the metabolic rate in order to carry out a correct risk assessment which quantifies the risk exactly.

Mobile camera-space manipulation

NASA Technical Reports Server (NTRS)

Seelinger, Michael J. (Inventor); Yoder, John-David S. (Inventor); Skaar, Steven B. (Inventor)

2001-01-01

The invention is a method of using computer vision to control systems consisting of a combination of holonomic and nonholonomic degrees of freedom such as a wheeled rover equipped with a robotic arm, a forklift, and earth-moving equipment such as a backhoe or a front-loader. Using vision sensors mounted on the mobile system and the manipulator, the system establishes a relationship between the internal joint configuration of the holonomic degrees of freedom of the manipulator and the appearance of features on the manipulator in the reference frames of the vision sensors. Then, the system, perhaps with the assistance of an operator, identifies the locations of the target object in the reference frames of the vision sensors. Using this target information, along with the relationship described above, the system determines a suitable trajectory for the nonholonomic degrees of freedom of the base to follow towards the target object. The system also determines a suitable pose or series of poses for the holonomic degrees of freedom of the manipulator. With additional visual samples, the system automatically updates the trajectory and final pose of the manipulator so as to allow for greater precision in the overall final position of the system.

3DS-colorimeter based on a mobile phone camera for industrial applications

NASA Astrophysics Data System (ADS)

Miettinen, Jari; Martinkauppi, J. Birgitta; Suopajärvi, Pekka

2013-02-01

Colour gives an essential finishing touch to many products. Consumers find it as an important factor, for example, when selecting doors, furniture, parquet and coated metal products. Currently, colour evaluation is often carried out by looking at the product. Since people's memory for an exact colour is poor, this method often produces unsatisfactory results in industrial quality control. In this paper, we discuss how to solve this problem by the use of a colour measurement technology for mobile phones equipped with a suitable accessory. Mobile phones provide a suitable monitor platform even for laymen as people are increasingly using their mobile devices for purposes of entertainment, communication and business, thus making them a familiar device to use. Our 3DS-colorimeter is a new, handheld, low-cost consumer/industrial-level prototype combining both a colorimeter feature and 3D surface measurement feature. In this paper, we describe its colorimeter features shortly and demonstrate its performance in measurement repeatability and colorimetric accuracy. As an application example, we show its usefulness for monitoring the colour appearance of painted doors. This study indicates that the 3DS-colorimeter is applicable to industrial quality control.

Study of the viscosity of hydrocarbon mixtures under pressure and temperature: A critical model of the corresponding states to double reference in the modeling domain.

NASA Astrophysics Data System (ADS)

Ettahir, Aziz; Boned, Christian; Lagourette, Bernard; Kettani, Kamal; Amarrayi, Khaoula; Garoumi, Mohammed

2017-10-01

The studied predictive model of behavior viscosimetric is the model of K.A. Petersen [1]. The dominant idea of this method is to characterize the viscosity of a fluid from two models taken as a reference in passing through a reduced pressure. The method is corresponding state with two references. This study shows that this method is dependent on the choice of reference and for each of the possibilities of C10/C6H6 and C1/C10 references . The results were investigated for four different weight ratios. It shows that the introduction of an adjusted coefficient does not improve significantly compared to results without adjustment factor, which appears to be the best choice. Regarding the influence of the choice of references, generally the two couples appear suitable but we noted that the choice is not necessary. In the case of mixtures containing at least one aromatic, the results are correct, especially if one takes the ratio of adjustment and our ratio without adjustment compared to that of K. A. PETERSEN[1]. The experimental results of the viscosity exhibit a good agreement with the calculated values. We can predict that the relative improvement is the finding that the introduction of the second body of reference (C10) from the model states corresponding to a reference (C1) of the authors.

University role in astronaut life support systems: Space power supply systems

NASA Technical Reports Server (NTRS)

Chin, L. Y.

1972-01-01

A brief description is given of the schemes suggested for providing electrical power aboard spacecraft. An attempt was made to list the major advantages and disadvantages of each scheme and to identify the particular areas in which it appears likely further research work may prove fruitful. Special attention was given to those research areas that appear suitable for colleges and university work. Chemical, solar, and nuclear power sources are considered together with the appropriate thermoelectric and turboelectric conversion systems.

Identification of suitable sites for mountain ginseng cultivation using GIS and geo-temperature.

PubMed

Kang, Hag Mo; Choi, Soo Im; Kim, Hyun

2016-01-01

This study was conducted to explore an accurate site identification technique using a geographic information system (GIS) and geo-temperature (gT) for locating suitable sites for growing cultivated mountain ginseng (CMG; Panax ginseng), which is highly sensitive to the environmental conditions in which it grows. The study site was Jinan-gun, South Korea. The spatial resolution for geographic data was set at 10 m × 10 m, and the temperatures for various climatic factors influencing CMG growth were calculated by averaging the 3-year temperatures obtained from the automatic weather stations of the Korea Meteorological Administration. Identification of suitable sites for CMG cultivation was undertaken using both a conventional method and a new method, in which the gT was added as one of the most important factors for crop cultivation. The results yielded by the 2 methods were then compared. When the gT was added as an additional factor (new method), the proportion of suitable sites identified decreased by 0.4 % compared with the conventional method. However, the proportion matching real CMG cultivation sites increased by 3.5 %. Moreover, only 68.2 % corresponded with suitable sites identified using the conventional factors; i.e., 31.8 % were newly detected suitable sites. The accuracy of GIS-based identification of suitable CMG cultivation sites improved by applying the temperature factor (i.e., gT) in addition to the conventionally used factors.

Estimating Rooftop Suitability for PV: A Review of Methods, Patents, and Validation Techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Melius, J.; Margolis, R.; Ong, S.

2013-12-01

A number of methods have been developed using remote sensing data to estimate rooftop area suitable for the installation of photovoltaics (PV) at various geospatial resolutions. This report reviews the literature and patents on methods for estimating rooftop-area appropriate for PV, including constant-value methods, manual selection methods, and GIS-based methods. This report also presents NREL's proposed method for estimating suitable rooftop area for PV using Light Detection and Ranging (LiDAR) data in conjunction with a GIS model to predict areas with appropriate slope, orientation, and sunlight. NREL's method is validated against solar installation data from New Jersey, Colorado, and Californiamore » to compare modeled results to actual on-the-ground measurements.« less

Individual responsibility for healthcare financing: application of an analytical framework exploring the suitability of private financing of assistive devices.

PubMed

Tinghög, Gustav; Carlsson, Per

2012-12-01

To operationalise and apply a conceptual framework for exploring when health services contain characteristics that facilitate individuals' ability to take individual responsibility for health care through out-of-pocket payment. In addition, we investigate if the levels of out-of-pocket payment for assistive devices (ADs) in Sweden are in line with the proposed framework. Focus groups were used to operationalise the core concepts of sufficient knowledge, individual autonomy, positive externalities, sufficient demand, affordability, and lifestyle enhancement into a measurable and replicable rationing tool. A selection of 28 ADs were graded separately as having high, medium, or low suitability for private financing according to the measurement scale provided through the operationalised framework. To investigate the actual level of private financing, a questionnaire about the level of out-of-pocket payment for the specific ADs was administered to county councils in Sweden. Concepts were operationalised into three levels indicating possible suitability for private financing. Responses to the questionnaire indicate that financing of ADs in Sweden varies across county councils as regards co-payment, full payment, discretionary payment for certain healthcare consumer groups, and full reimbursement. According to the framework, ADs commonly funded privately were generally considered to be more suitable for private financing. Sufficient knowledge, individual autonomy, and sufficient demand did not appear to influence why certain ADs were financed out-of-pocket. The level of positive externalities, affordability, and lifestyle enhancement appeared to be somewhat higher for ADs that were financed out-of-pocket, but the differences were small. Affordability seemed to be the most influential concept.

Progressive multi-atlas label fusion by dictionary evolution.

PubMed

Song, Yantao; Wu, Guorong; Bahrami, Khosro; Sun, Quansen; Shen, Dinggang

2017-02-01

Accurate segmentation of anatomical structures in medical images is important in recent imaging based studies. In the past years, multi-atlas patch-based label fusion methods have achieved a great success in medical image segmentation. In these methods, the appearance of each input image patch is first represented by an atlas patch dictionary (in the image domain), and then the latent label of the input image patch is predicted by applying the estimated representation coefficients to the corresponding anatomical labels of the atlas patches in the atlas label dictionary (in the label domain). However, due to the generally large gap between the patch appearance in the image domain and the patch structure in the label domain, the estimated (patch) representation coefficients from the image domain may not be optimal for the final label fusion, thus reducing the labeling accuracy. To address this issue, we propose a novel label fusion framework to seek for the suitable label fusion weights by progressively constructing a dynamic dictionary in a layer-by-layer manner, where the intermediate dictionaries act as a sequence of guidance to steer the transition of (patch) representation coefficients from the image domain to the label domain. Our proposed multi-layer label fusion framework is flexible enough to be applied to the existing labeling methods for improving their label fusion performance, i.e., by extending their single-layer static dictionary to the multi-layer dynamic dictionary. The experimental results show that our proposed progressive label fusion method achieves more accurate hippocampal segmentation results for the ADNI dataset, compared to the counterpart methods using only the single-layer static dictionary. Copyright © 2016 Elsevier B.V. All rights reserved.

Nano/micro hybrid scaffold of PCL or P3HB nanofibers combined with silk fibroin for tendon and ligament tissue engineering.

PubMed

Naghashzargar, Elham; Farè, Silvia; Catto, Valentina; Bertoldi, Serena; Semnani, Dariush; Karbasi, Saeed; Tanzi, Maria Cristina

2015-07-04

A novel biodegradable nano/micro hybrid structure was obtained by electrospinning P3HB or PCL nanofibers onto a twisted silk fibroin (SF) structure, with the aim of fabricating a suitable scaffold for tendon and ligament tissue engineering. The electrospinning (ES) processing parameters for P3HB and PCL were optimized on 2D samples, and applied to produce two different nano/micro hybrid constructs (SF/ES-PCL and SF/ES-P3HB).Morphological, chemico-physical and mechanical properties of the novel hybrid scaffolds were evaluated by SEM, ATR FT-IR, DSC, tensile and thermodynamic mechanical tests. The results demonstrated that the nanofibers were tightly wrapped around the silk filaments, and the crystallinity of the SF twisted yarns was not influenced by the presence of the electrospun polymers. The slightly higher mechanical properties of the hybrid constructs confirmed an increase of internal forces due to the interaction between nano and micro components. Cell culture tests with L929 fibroblasts, in the presence of the sample eluates or in direct contact with the hybrid structures, showed no cytotoxic effects and a good level of cytocompatibility of the nano/micro hybrid structures in term of cell viability, particularly at day 1. Cell viability onto the nano/micro hybrid structures decreased from the first to the third day of culture when compared with the control culture plastic, but appeared to be higher when compared with the uncoated SF yarns. Although additional in vitro and in vivo tests are needed, the original fabrication method here described appears promising for scaffolds suitable for tendon and ligament tissue engineering.

A Semi-Discrete Landweber-Kaczmarz Method for Cone Beam Tomography and Laminography Exploiting Geometric Prior Information

NASA Astrophysics Data System (ADS)

Vogelgesang, Jonas; Schorr, Christian

2016-12-01

We present a semi-discrete Landweber-Kaczmarz method for solving linear ill-posed problems and its application to Cone Beam tomography and laminography. Using a basis function-type discretization in the image domain, we derive a semi-discrete model of the underlying scanning system. Based on this model, the proposed method provides an approximate solution of the reconstruction problem, i.e. reconstructing the density function of a given object from its projections, in suitable subspaces equipped with basis function-dependent weights. This approach intuitively allows the incorporation of additional information about the inspected object leading to a more accurate model of the X-rays through the object. Also, physical conditions of the scanning geometry, like flat detectors in computerized tomography as used in non-destructive testing applications as well as non-regular scanning curves e.g. appearing in computed laminography (CL) applications, are directly taken into account during the modeling process. Finally, numerical experiments of a typical CL application in three dimensions are provided to verify the proposed method. The introduction of geometric prior information leads to a significantly increased image quality and superior reconstructions compared to standard iterative methods.

Normative Data for an Instrumental Assessment of the Upper-Limb Functionality.

PubMed

Caimmi, Marco; Guanziroli, Eleonora; Malosio, Matteo; Pedrocchi, Nicola; Vicentini, Federico; Molinari Tosatti, Lorenzo; Molteni, Franco

2015-01-01

Upper-limb movement analysis is important to monitor objectively rehabilitation interventions, contributing to improving the overall treatments outcomes. Simple, fast, easy-to-use, and applicable methods are required to allow routinely functional evaluation of patients with different pathologies and clinical conditions. This paper describes the Reaching and Hand-to-Mouth Evaluation Method, a fast procedure to assess the upper-limb motor control and functional ability, providing a set of normative data from 42 healthy subjects of different ages, evaluated for both the dominant and the nondominant limb motor performance. Sixteen of them were reevaluated after two weeks to perform test-retest reliability analysis. Data were clustered into three subgroups of different ages to test the method sensitivity to motor control differences. Experimental data show notable test-retest reliability in all tasks. Data from older and younger subjects show significant differences in the measures related to the ability for coordination thus showing the high sensitivity of the method to motor control differences. The presented method, provided with control data from healthy subjects, appears to be a suitable and reliable tool for the upper-limb functional assessment in the clinical environment.

Normative Data for an Instrumental Assessment of the Upper-Limb Functionality

PubMed Central

Caimmi, Marco; Guanziroli, Eleonora; Malosio, Matteo; Pedrocchi, Nicola; Vicentini, Federico; Molinari Tosatti, Lorenzo; Molteni, Franco

2015-01-01

Upper-limb movement analysis is important to monitor objectively rehabilitation interventions, contributing to improving the overall treatments outcomes. Simple, fast, easy-to-use, and applicable methods are required to allow routinely functional evaluation of patients with different pathologies and clinical conditions. This paper describes the Reaching and Hand-to-Mouth Evaluation Method, a fast procedure to assess the upper-limb motor control and functional ability, providing a set of normative data from 42 healthy subjects of different ages, evaluated for both the dominant and the nondominant limb motor performance. Sixteen of them were reevaluated after two weeks to perform test-retest reliability analysis. Data were clustered into three subgroups of different ages to test the method sensitivity to motor control differences. Experimental data show notable test-retest reliability in all tasks. Data from older and younger subjects show significant differences in the measures related to the ability for coordination thus showing the high sensitivity of the method to motor control differences. The presented method, provided with control data from healthy subjects, appears to be a suitable and reliable tool for the upper-limb functional assessment in the clinical environment. PMID:26539500

Strengthening of bridges by post-tensioning using monostrands in substituted cable ducts

NASA Astrophysics Data System (ADS)

Klusáček, Ladislav; Svoboda, Adam

2017-09-01

Post-tensioning is suitable, reliable and durable method of strengthening existing engineering structures, especially bridges. The high efficiency of post-tensioning can be seen in many applications throughout the world. In this paper the method is extended by a structural system of substituted cable ducts, which allows for significantly widening application of prestressing so it’s convenient mostly for application on beam bridges or slab bridges (built in years 1920 - 1960). The method of substituted cable ducts is based on theoretical knowledge and technical procedures, which were made possible through the development in prestressing systems, particularly the development of prestressing tendons (monostrands) and encased anchorages, as well as progress in drilling technology. This technique is highly recommended due to minimization of interventions into the constructions, unseen method of cable arrangement and hence the absence of impact on appearance, which is appreciated not only in case of valuable historical structures but also in general. It is possible to summarise that posttensioning by monostrands in substituted cable ducts is a highly effective method of strengthening existing bridges in order to increase their load capacities in terms of current traffic load and to extend their service life.

Application of selected ion monitoring to the analysis of triacylglycerols in olive oil by high temperature-gas chromatography/mass spectrometry.

PubMed

Ruiz-Samblás, C; González-Casado, A; Cuadros-Rodríguez, L; García, F P Rodríguez

2010-06-30

The analysis of the triacylglycerol (TAG) composition of oils is a very challenging task, since the TAGs have very similar physico-chemical properties. In this work, a high temperature-gas chromatographic method coupled to electron ionization-mass spectrometry (HT-GC/EI-MS), in the Selected Ion Monitoring (SIM) mode, method was developed for the analysis of TAGs in the olive oil; this is a method suitable for routine analysis. This method was developed using commercially available standard TAGs. The TAGs studied were separated according to their equivalent carbon number and degree of unsaturation. The peak assignment was carried out by locating the characteristic fragment ions having the same retention time on the SIM profile such as [RCO+74](+) and [RCO+128](+) ions, due to the fatty acyl residues on sn-1, sn-2 and sn-3 positions of the TAG molecule and the [M-OCOR](+) ions corresponding to the acyl ions. The developed method was very useful to eliminate the interferences that appeared in the mass spectrum since electron ionization can prevent satisfactory interpretation of spectra. Copyright 2010 Elsevier B.V. All rights reserved.

Test site suitability assessment for radiation measurements

NASA Astrophysics Data System (ADS)

Borsero, M.; Nano, E.

1980-04-01

Field and attenuation methods for site suitability assessment for radiation measurements are presented. Attention is given to the IEC procedure for checking the suitability of radiation measurement site.

Methods, compounds and systems for detecting a microorganism in a sample

DOEpatents

Colston, Jr, Bill W.; Fitch, J. Patrick; Gardner, Shea N.; Williams, Peter L.; Wagner, Mark C.

2016-09-06

Methods to identify a set of probe polynucleotides suitable for detecting a set of targets and in particular methods for identification of primers suitable for detection of target microorganisms related polynucleotides, set of polynucleotides and compositions, and related methods and systems for detection and/or identification of microorganisms in a sample.

Potential clinical application of masseter and temporal muscle massage treatment using an oral rehabilitation robot in temporomandibular disorder patients with myofascial pain.

PubMed

Ariji, Yoshiko; Nakayama, Miwa; Nishiyama, Wataru; Ogi, Nobumi; Sakuma, Shigemitsu; Katsumata, Akitoshi; Kurita, Kenichi; Ariji, Eiichiro

2015-10-01

To investigate the safety, suitable treatment regimen, and efficacy of masseter and temporal muscle massage treatment using an oral rehabilitation robot. Forty-one temporomandibular disorder (TMD) patients with myofascial pain (8 men, 33 women, median age: 46 years) were enrolled. The safety, suitable massage regimen, and efficacy of this treatment were investigated. Changes in masseter muscle thickness were evaluated on sonograms. No adverse events occurred with any of the treatment sessions. Suitable massage was at pressure of 10 N for 16 minutes. Five sessions were performed every 2 weeks. Total duration of treatment was 9·5 weeks in median. Massage treatment was effective in 70·3% of patients. Masseter muscle thickness decreased with treatment in the therapy-effective group. This study confirmed the safety of massage treatment, and established a suitable regimen. Massage was effective in 70·3% of patients and appeared to have a potential as one of the effective treatments for myofascial pain.

Liquid precursor for deposition of copper selenide and method of preparing the same

DOEpatents

Curtis, Calvin J.; Miedaner, Alexander; Franciscus Antonius Maria Van Hest, Marinus; Ginley, David S.; Hersh, Peter A.; Eldada, Louay; Stanbery, Billy J.

2015-09-08

Liquid precursors containing copper and selenium suitable for deposition on a substrate to form thin films suitable for semiconductor applications are disclosed. Methods of preparing such liquid precursors and methods of depositing a precursor on a substrate are also disclosed.

PREDICTING FIELD PERFORMANCE OF HERBACEOUS SPECIES FOR PHYTOREMEDIATION OF PERCHLORATE

EPA Science Inventory

Results of these short-term experiments coupled with ecological knowledge of the nine herbaceous plant species tested suggest that several species may by successful in on-site remediation of perchlorate. The two wetland species which appear to be most suitable for field experimen...

Habitat suitability and movement corridors of grey wolf (Canis lupus) in Northern Pakistan

PubMed Central

Kabir, Muhammad; Hameed, Shoaib; Ali, Hussain; Bosso, Luciano; Din, Jaffar Ud; Bischof, Richard; Redpath, Steve

2017-01-01

Habitat suitability models are useful to understand species distribution and to guide management and conservation strategies. The grey wolf (Canis lupus) has been extirpated from most of its historic range in Pakistan primarily due to its impact on livestock and livelihoods. We used non-invasive survey data from camera traps and genetic sampling to develop a habitat suitability model for C. lupus in northern Pakistan and to explore the extent of connectivity among populations. We detected suitable habitat of grey wolf using a maximum entropy approach (Maxent ver. 3.4.0) and identified suitable movement corridors using the Circuitscape 4.0 tool. Our model showed high levels of predictive performances, as seen from the values of area under curve (0.971±0.002) and true skill statistics (0.886±0.021). The main predictors for habitat suitability for C. lupus were distances to road, mean temperature of the wettest quarter and distance to river. The model predicted ca. 23,129 km2 of suitable areas for wolf in Pakistan, with much of suitable habitat in remote and inaccessible areas that appeared to be well connected through vulnerable movement corridors. These movement corridors suggest that potentially the wolf range can expand in Pakistan’s Northern Areas. However, managing protected areas with stringent restrictions is challenging in northern Pakistan, in part due to heavy dependence of people on natural resources. The habitat suitability map provided by this study can inform future management strategies by helping authorities to identify key conservation areas. PMID:29121089

Spatio-temporal phenomena in complex systems with time delays

NASA Astrophysics Data System (ADS)

Yanchuk, Serhiy; Giacomelli, Giovanni

2017-03-01

Real-world systems can be strongly influenced by time delays occurring in self-coupling interactions, due to unavoidable finite signal propagation velocities. When the delays become significantly long, complicated high-dimensional phenomena appear and a simple extension of the methods employed in low-dimensional dynamical systems is not feasible. We review the general theory developed in this case, describing the main destabilization mechanisms, the use of visualization tools, and commenting on the most important and effective dynamical indicators as well as their properties in different regimes. We show how a suitable approach, based on a comparison with spatio-temporal systems, represents a powerful instrument for disclosing the very basic mechanism of long-delay systems. Various examples from different models and a series of recent experiments are reported.

The Prevention of Ice Formation on Gasoline Tank Vents

NASA Technical Reports Server (NTRS)

Theodorsen, Theodore; Clay, William C

1931-01-01

This investigation was conducted in the refrigerated wind tunnel at the Langley Memorial Aeronautical Laboratory, Langley Field, Va., to determine a suitable method for preventing the formation of ice on the vents of airplane gasoline tanks. Tests were made on a variety of vent forms arranged in a number of different orientations relative to the direction of the air stream. Both the size of the tube and its orientation were found to be of great importance. Small tubes, under equal circumstances, were found to freeze over far more rapidly than large ones. Tubes pointing downstream, or shielded in other ways, appear to be perfectly immune against this hazard. A tube 3/4 inch in diameter with the opening pointing downstream is finally recommended as being the safest choice of gas tank vent.

Towards Automated Screening of Two-dimensional Crystals

PubMed Central

Cheng, Anchi; Leung, Albert; Fellmann, Denis; Quispe, Joel; Suloway, Christian; Pulokas, James; Carragher, Bridget; Potter, Clinton S.

2007-01-01

Screening trials to determine the presence of two-dimensional (2D) protein crystals suitable for three-dimensional structure determination using electron crystallography is a very labor-intensive process. Methods compatible with fully automated screening have been developed for the process of crystal production by dialysis and for producing negatively stained grids of the resulting trials. Further automation via robotic handling of the EM grids, and semi-automated transmission electron microscopic imaging and evaluation of the trial grids is also possible. We, and others, have developed working prototypes for several of these tools and tested and evaluated them in a simple screen of 24 crystallization conditions. While further development of these tools is certainly required for a turn-key system, the goal of fully automated screening appears to be within reach. PMID:17977016

Development of europium doped BaSO{sub 4} TL OSL dual phosphor for radiation dosimetry applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patle, Anita, E-mail: patle.anita25@gmail.com; Patil, R. R.; Kulkarni, M. S.

This paper presents the results on the preparation and characterization of Europium-doped Barium sulfate (BaSO{sub 4}: Eu) TL /OSL dual phosphor. The OSL sensitivity was found to be 11% of the commercially available Al{sub 2}O{sub 3}: C, using area integration method. The sample also shows good TL sensitivity and the dosimetric peak appears around 190°C with a shoulder at 282°C. After OSL readout, No change in the TL glow curve is observed. Since the observed TL peaks are not responsible for the observed OSL, good OSL as well as TL sensitivity and low fading will make this phosphor suitable formore » applications in radiation dosimetry using OSL as well as TL.« less

Comparison of multispectral remote-sensing techniques for monitoring subsurface drain conditions. [Imperial Valley, California

NASA Technical Reports Server (NTRS)

Goettelman, R. C.; Grass, L. B.; Millard, J. P.; Nixon, P. R.

1983-01-01

The following multispectral remote-sensing techniques were compared to determine the most suitable method for routinely monitoring agricultural subsurface drain conditions: airborne scanning, covering the visible through thermal-infrared (IR) portions of the spectrum; color-IR photography; and natural-color photography. Color-IR photography was determined to be the best approach, from the standpoint of both cost and information content. Aerial monitoring of drain conditions for early warning of tile malfunction appears practical. With careful selection of season and rain-induced soil-moisture conditions, extensive regional surveys are possible. Certain locations, such as the Imperial Valley, Calif., are precluded from regional monitoring because of year-round crop rotations and soil stratification conditions. Here, farms with similar crops could time local coverage for bare-field and saturated-soil conditions.

A new formulation for anisotropic radiative transfer problems. I - Solution with a variational technique

NASA Technical Reports Server (NTRS)

Cheyney, H., III; Arking, A.

1976-01-01

The equations of radiative transfer in anisotropically scattering media are reformulated as linear operator equations in a single independent variable. The resulting equations are suitable for solution by a variety of standard mathematical techniques. The operators appearing in the resulting equations are in general nonsymmetric; however, it is shown that every bounded linear operator equation can be embedded in a symmetric linear operator equation and a variational solution can be obtained in a straightforward way. For purposes of demonstration, a Rayleigh-Ritz variational method is applied to three problems involving simple phase functions. It is to be noted that the variational technique demonstrated is of general applicability and permits simple solutions for a wide range of otherwise difficult mathematical problems in physics.

Fuel-efficient cruise performance model for general aviation piston engine airplanes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parkinson, R.C.H.

1982-01-01

The uses and limitations of typical Pilot Operating Handbook cruise performance data, for constructing cruise performance models suitable for maximizing specific range, are first examined. These data are found to be inadequate for constructing such models. A new model of General Aviation piston-prop airplane cruise performance is then developed. This model consists of two subsystem models: the airframe-propeller-atmosphere subsystem model; and the engine-atmosphere subsystem model. The new model facilitates maximizing specific range; and by virtue of its simplicity and low volume data storage requirements, appears suitable for airborne microprocessor implementation.

The Mantel-Haenszel procedure revisited: models and generalizations.

PubMed

Fidler, Vaclav; Nagelkerke, Nico

2013-01-01

Several statistical methods have been developed for adjusting the Odds Ratio of the relation between two dichotomous variables X and Y for some confounders Z. With the exception of the Mantel-Haenszel method, commonly used methods, notably binary logistic regression, are not symmetrical in X and Y. The classical Mantel-Haenszel method however only works for confounders with a limited number of discrete strata, which limits its utility, and appears to have no basis in statistical models. Here we revisit the Mantel-Haenszel method and propose an extension to continuous and vector valued Z. The idea is to replace the observed cell entries in strata of the Mantel-Haenszel procedure by subject specific classification probabilities for the four possible values of (X,Y) predicted by a suitable statistical model. For situations where X and Y can be treated symmetrically we propose and explore the multinomial logistic model. Under the homogeneity hypothesis, which states that the odds ratio does not depend on Z, the logarithm of the odds ratio estimator can be expressed as a simple linear combination of three parameters of this model. Methods for testing the homogeneity hypothesis are proposed. The relationship between this method and binary logistic regression is explored. A numerical example using survey data is presented.

The Mantel-Haenszel Procedure Revisited: Models and Generalizations

PubMed Central

Fidler, Vaclav; Nagelkerke, Nico

2013-01-01

Several statistical methods have been developed for adjusting the Odds Ratio of the relation between two dichotomous variables X and Y for some confounders Z. With the exception of the Mantel-Haenszel method, commonly used methods, notably binary logistic regression, are not symmetrical in X and Y. The classical Mantel-Haenszel method however only works for confounders with a limited number of discrete strata, which limits its utility, and appears to have no basis in statistical models. Here we revisit the Mantel-Haenszel method and propose an extension to continuous and vector valued Z. The idea is to replace the observed cell entries in strata of the Mantel-Haenszel procedure by subject specific classification probabilities for the four possible values of (X,Y) predicted by a suitable statistical model. For situations where X and Y can be treated symmetrically we propose and explore the multinomial logistic model. Under the homogeneity hypothesis, which states that the odds ratio does not depend on Z, the logarithm of the odds ratio estimator can be expressed as a simple linear combination of three parameters of this model. Methods for testing the homogeneity hypothesis are proposed. The relationship between this method and binary logistic regression is explored. A numerical example using survey data is presented. PMID:23516463

Preparation of resveratrol-loaded nanoporous silica materials with different structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Popova, Margarita, E-mail: mpopova@orgchem.bas.bg; Szegedi, Agnes; Mavrodinova, Vesselina

2014-11-15

Solid, nanoporous silica-based spherical mesoporous MCM-41 and KIL-2 with interparticle mesoporosity as well as nanosized zeolite BEA materials differing in morphology and pore size distribution, were used as carriers for the preparation of resveratrol-loaded delivery systems. Two preparation methods have been applied: (i) loading by mixing of resveratrol and mesoporous carrier in solid state and (ii) deposition in ethanol solution. The parent and the resveratrol loaded carriers were characterized by XRD, TEM, N2 physisorption, thermal analysis, and FT-IR spectroscopy. The influence of the support structure on the adsorption capacity and the release kinetics of this poorly soluble compound were investigated.more » Our results indicated that the chosen nanoporous silica supports are suitable for stabilization of trans-resveratrol and reveal controlled release and ability to protect the supported compound against degradation regardless of loading method. The solid-state dry mixing appears very effective for preparation of drug formulations composed of poorly soluble compound. - Graphical abstract: trans-Resveratrol was stabilized in the pores of BEA zeolite, MCM-41and KIL2 mesoporous silicas. - Highlights: • BEA, KIL-2 and MCM-41 materials were used as carriers for resveratrol loading. • Resveratrol encapsulation in ethanol solution and solid state procedure were applied. • The solid-state preparation appears very effective for stabilization of trans-resveratrol.« less

Extraction of immune and inflammatory cells from human lung parenchyma: evaluation of an enzymatic digestion procedure.

PubMed Central

Holt, P G; Robinson, B W; Reid, M; Kees, U R; Warton, A; Dawson, V H; Rose, A; Schon-Hegrad, M; Papadimitriou, J M

1986-01-01

The inflammatory and immune cell populations of the human lung parenchyma have not been characterized in detail. This report describes a novel and efficient procedure for their extraction. Histologically normal human lung tissue samples from pneumonectomy specimens were sliced to 0.5 mm, and digested in collagenase/DNAse. Viable mononuclear cell yields ranged from 15-48 X 10(6)/g, and were markedly in excess of reported methods employing mechanical tissue disruption, which normally yield populations containing almost exclusively macrophages. The lung digest population was examined by flow cytometry using monoclonal antibodies against cell surface receptors, and found to comprise up to 40% T lymphocytes, 10% B lymphocytes and 30% macrophages, contaminated by less than 1% peripheral blood cells. Based upon these figures, the recoverable lung parenchymal lymphoid cell pool appears considerably larger than previously recognized, being of the same order as the peripheral blood pool. Initial functional studies suggest that such cellular activities as antigen-specific T cell proliferation, antigen-presentation, interleukin 1 production and natural killer cell activity survive the extraction process, and controlled enzymatic digestion experiments with peripheral blood cells indicate that the degree of enzyme-mediated damage to these functions and to cell-surface structures, was minimal. The extraction method thus appears suitable for studying the types and functions of human parenchymal lung cells in health and disease. Images Fig. 2 p195-a PMID:3026698

Liquid precursor for deposition of indium selenide and method of preparing the same

DOEpatents

Curtis, Calvin J.; Miedaner, Alexander; van Hest, Marinus Franciscus Antonius Maria; Ginley, David S.; Hersh, Peter A.; Eldada, Louay; Stanbery, Billy J.

2015-09-22

Liquid precursors containing indium and selenium suitable for deposition on a substrate to form thin films suitable for semiconductor applications are disclosed. Methods of preparing such liquid precursors and method of depositing a liquid precursor on a substrate are also disclosed.

Monitoring of KrF excimer laser ablation for burn scars: a comparative study of transient reflection measurement and time-resolved photography of ablation plume

NASA Astrophysics Data System (ADS)

Nakajima, Akio; Arai, Tsunenori; Kikuchi, Makoto; Iwaya, Akimi; Arai, Katsuyuki; Inazaki, Satoshi; Takaoka, Takatsugu; Kato, Masayoshi

1995-05-01

A simple laser ablation monitoring during burn scar removal by KrF laser irradiation was studied to control laser fluence in real-time. Because, to obtain suitable surface for auto skin-graft, the laser fluence should be precisely controlled at each laser shot. We employed simple probe transmission method which could detect ejected material/phenomena from irradiated surface. The time-course of measured probe intensity contained a couple of attenuated peaks, which might corresponded to a shock wave front and debris plume. The delay time from laser irradiation to the debris plume peak appearance varied with the ablation fluence. The delay time of 1 J/cm2 (near ablation threshold) case prolonged 25% from 8 J/cm2 (far above threshold) case. Therefore, we think the delay time measurement by means of the simple probe transmission method may be available to attain the laser fluence control for nonuniform burn scar removal. The time-resolved photography and probe reflection method were also studied to understand the measured time-course of the transmitted probe intensity.

Loop-mediated isothermal amplification for detection of Staphylococcus aureus in dairy cow suffering from mastitis.

PubMed

Tie, Zhang; Chunguang, Wang; Xiaoyuan, Wei; Xinghua, Zhao; Xiuhui, Zhong

2012-01-01

To develop a rapid detection method of Staphylococcus aureus using loop-mediated isothermal amplification (LAMP), four specific primers were designed according to six distinct sequences of the nuc gene. In addition, the specificity and sensitivity of LAMP were verified and compared with those of PCR. Results showed that the LAMP reaction was completed within 45 min at 62.5°C, and ladder bands were appeared in LAMP products analyzed by gel electrophoresis. After adding 1x SYBR Green l, the positive reaction tube showed green color and the negative reaction tube remained orange, indicating that the LAMP has high specificity. The minimal detectable concentration of LAMP was 1 × 10² CFU/mL and that of PCR was 1 × 10⁴ CFU/mL, indicating that the LAMP was 100 times more sensitive than the PCR. The LAMP method for detection of Staphylococcus aureus has many advantages, such as simple operation, high sensitivity, high specificity, and rapid analysis. Therefore, this method is more suitable for the rapid on-site detection of Staphylococcus aureus.

Bispectral analysis: comparison of two windowing functions

NASA Astrophysics Data System (ADS)

Silvagni, D.; Djerroud, C.; Réveillé, T.; Gravier, E.

2018-02-01

Amongst all the normalized forms of bispectrum, the bicoherence is shown to be a very useful diagnostic tool in experimental studies of nonlinear wave interactions in plasma, as it measures the fraction of wave power due to the quadratic wave coupling in a self-excited fluctuation spectrum [1, 2]. In order to avoid spectral leakage, the application of a windowing function is needed during the bicoherence computation. Spectral leakage from statistically dependent components are of crucial importance in the discrimination between coupled and uncoupled modes, as they will introduce in the bicoherence spectrum phase-coupled modes which in reality do not exist. Therefore, the windowing function plays a key role in the bicoherence estimation. In this paper, two windowing methods are compared: the multiplication of the initial signal by the Hanning function and the subtraction of the straight line which links the two extremities of the signal. The influence of these two windowing methods on both the power spectrum and the bicoherence spectrum is showed. Although both methods give precise results, the Hanning function appears to be the more suitable window.

Retrieval of land cover information under thin fog in Landsat TM image

NASA Astrophysics Data System (ADS)

Wei, Yuchun

2008-04-01

Thin fog, which often appears in remote sensing image of subtropical climate region, has resulted in the low image quantity and bad image mapping. Therefore, it is necessary to develop the image processing method to retrieve land cover information under thin fog. In this paper, the Landsat TM image near the Taihu Lake that is in the subtropical climate zone of China was used as an example, and the workflow and method used to retrieve the land cover information under thin fog have been built based on ENVI software and a single TM image. The basic step covers three parts: 1) isolating the thin fog area in image according to the spectral difference of different bands; 2) retrieving the visible band information of different land cover types under thin fog from the near-infrared bands according to the relationships between near-infrared bands and visible bands of different land cover types in the area without fog; 3) image post-process. The result showed that the method in the paper is easy and suitable, and can be used to improve the quantity of TM image mapping more effectively.

Determination of Grayanotoxins from Rhododendron brachycarpum in Dietary Supplements and Homemade Wine by Liquid Chromatography-Quadrupole Time-of-Flight-Mass Spectrometry and Liquid Chromatography-Tandem Mass Spectrometry.

PubMed

Hwang, Taeik; Noh, Eunyoung; Jeong, Ji Hye; Park, Sung-Kwan; Shin, Dongwoo; Kang, Hoil

2018-02-28

A sensitive and specific high-performance liquid chromatography-quadrupole time-of-flight-mass spectrometry (LC-QTOF-MS) method combined with liquid chromatography-tandem mass spectrometry (LC-MS/MS) was developed for the determination of grayanotoxins I and III in dietary supplements and homemade wine. Grayanotoxins I and III were successfully extracted using solid-phase extraction cartridges, characterized by LC-QTOF-MS, and quantitated by LC-MS/MS. The LC-MS/MS calibration curves were linear over concentrations of 10-100 ng/mL (grayanotoxin I) and 20-400 ng/mL (grayanotoxin III). Grayanotoxins I and III were found in 51 foodstuffs, with quantitative determinations revealing total toxin concentrations of 18.4-101 000 ng/mL (grayanotoxin I) and 15.3-56 000 ng/mL (grayanotoxin III). The potential of the validated method was demonstrated by successful quantitative analysis of grayanotoxins I and III in dietary supplements and homemade wine; the method appears suitable for the routine detection of grayanotoxins I and III from Rhododendron brachycarpum.

Use of doubly labeled water technique in soldiers training for jungle warfare

DOE Office of Scientific and Technical Information (OSTI.GOV)

Forbes-Ewan, C.H.; Morrissey, B.L.; Gregg, G.C.

1989-07-01

The doubly labeled water method was used to estimate the energy expended by four members of an Australian Army platoon (34 soldiers) engaged in training for jungle warfare. Each subject received an oral isotope dose sufficient to raise isotope levels by 200-250 ({sup 18}O) and 100-120 ppm ({sup 2}H). The experimental period was 7 days. Concurrently, a factorial estimate of the energy expenditure of the platoon was conducted. Also, a food intake-energy balance study was conducted for the platoon. Mean daily energy expenditure by the doubly labeled water method was 4,750 kcal (range 4,152-5,394 kcal). The factorial estimate of meanmore » daily energy expenditure was 4,535 kcal. Because of inherent inaccuracies in the food intake-energy balance technique, we were able to conclude only that energy expenditure, as measured by this method, was greater than the estimated mean daily intake of 4,040 kcal. The doubly labeled water technique was well tolerated, is noninvasive, and appears to be suitable in a wide range of field applications.« less

76 FR 82201 - General Site Suitability Criteria for Nuclear Power Stations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-30

..., and 52 [NRC-2011-0297] General Site Suitability Criteria for Nuclear Power Stations AGENCY: Nuclear... Suitability Criteria for Nuclear Power Stations.'' This guide describes a method that the NRC staff considers acceptable to implement the site suitability requirements for nuclear power stations. DATES: Submit comments...

Modeling the Kinetics of Deactivation of Catalysts during the Upgrading of Bio-Oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weber, Robert S.; Olarte, Mariefel V.; Wang, Huamin

The fouling of catalysts for the upgrading of bio-oils appears to be very different from the fouling of catalysts for the hydroprocessing of petroleum-derived streams. There are two reasons for the differences: a) bio-oil contains polarizable components and phases that can stabilize reaction intermediates exhibiting charge separation and b) bio-oil components contain functional groups that contain O, notably carbonyls (>C=O). Aldol condensation of carbonyls affords very different pathways for the production of oligomeric, refractory deposits than does dehydrogenation/polymerization of petroleum-derived hydrocarbons. Colloquially, we refer to the bio-oil derived deposits as “gunk” to discriminate them from coke, the carbonaceous deposits encounteredmore » in petroleum refining. Classical gelation, appears to be a suitable model for the “gunking” reaction. Our work has helped explain the temperature range at which bio-oil should be pre-processed (“stabilized”) to confer longer lifetimes on the catalysts used for more severe processing. Stochastic modeling (kinetic Monte Carlo simulations) appears suitable to capture the rates of oligomerization of bio-oil. This work was supported by the US Department of Energy, Office of Energy Efficiency and Renewable Energy, Bioenergy Technologies Office. Pacific Northwest National Laboratory (PNNL) is a multiprogram national laboratory operated for DOE by Battelle.« less

External Standards or Standard Addition? Selecting and Validating a Method of Standardization

NASA Astrophysics Data System (ADS)

Harvey, David T.

2002-05-01

A common feature of many problem-based laboratories in analytical chemistry is a lengthy independent project involving the analysis of "real-world" samples. Students research the literature, adapting and developing a method suitable for their analyte, sample matrix, and problem scenario. Because these projects encompass the complete analytical process, students must consider issues such as obtaining a representative sample, selecting a method of analysis, developing a suitable standardization, validating results, and implementing appropriate quality assessment/quality control practices. Most textbooks and monographs suitable for an undergraduate course in analytical chemistry, however, provide only limited coverage of these important topics. The need for short laboratory experiments emphasizing important facets of method development, such as selecting a method of standardization, is evident. The experiment reported here, which is suitable for an introductory course in analytical chemistry, illustrates the importance of matrix effects when selecting a method of standardization. Students also learn how a spike recovery is used to validate an analytical method, and obtain a practical experience in the difference between performing an external standardization and a standard addition.

Use of non-linear mixed-effects modelling and regression analysis to predict the number of somatic coliphages by plaque enumeration after 3 hours of incubation.

PubMed

Mendez, Javier; Monleon-Getino, Antonio; Jofre, Juan; Lucena, Francisco

2017-10-01

The present study aimed to establish the kinetics of the appearance of coliphage plaques using the double agar layer titration technique to evaluate the feasibility of using traditional coliphage plaque forming unit (PFU) enumeration as a rapid quantification method. Repeated measurements of the appearance of plaques of coliphages titrated according to ISO 10705-2 at different times were analysed using non-linear mixed-effects regression to determine the most suitable model of their appearance kinetics. Although this model is adequate, to simplify its applicability two linear models were developed to predict the numbers of coliphages reliably, using the PFU counts as determined by the ISO after only 3 hours of incubation. One linear model, when the number of plaques detected was between 4 and 26 PFU after 3 hours, had a linear fit of: (1.48 × Counts 3 h + 1.97); and the other, values >26 PFU, had a fit of (1.18 × Counts 3 h + 2.95). If the number of plaques detected was <4 PFU after 3 hours, we recommend incubation for (18 ± 3) hours. The study indicates that the traditional coliphage plating technique has a reasonable potential to provide results in a single working day without the need to invest in additional laboratory equipment.

"CultureGrams[TM]" and "StateGrams[TM]": Making Places and People Relevant to Elementary Students.

ERIC Educational Resources Information Center

Safford, Barbara Ripp

2002-01-01

Describes "CultureGrams" and "StateGrams", sources that provide practical cultural information including attitudes, appearances, greetings, gestures, dating, family life, transportation, health, and education. Focuses on the edition suitable for elementary school students, explaining specific features and suggesting assignments…

Biochar as potential sustainable precursors for activated carbon production: Multiple applications in environmental protection and energy storage.

PubMed

Tan, Xiao-Fei; Liu, Shao-Bo; Liu, Yun-Guo; Gu, Yan-Ling; Zeng, Guang-Ming; Hu, Xin-Jiang; Wang, Xin; Liu, Shao-Heng; Jiang, Lu-Hua

2017-03-01

There is a growing interest of the scientific community on production of activated carbon using biochar as potential sustainable precursors pyrolyzed from biomass wastes. Physical activation and chemical activation are the main methods applied in the activation process. These methods could have significantly beneficial effects on biochar chemical/physical properties, which make it suitable for multiple applications including water pollution treatment, CO 2 capture, and energy storage. The feedstock with different compositions, pyrolysis conditions and activation parameters of biochar have significant influences on the properties of resultant activated carbon. Compared with traditional activated carbon, activated biochar appears to be a new potential cost-effective and environmentally-friendly carbon materials with great application prospect in many fields. This review not only summarizes information from the current analysis of activated biochar and their multiple applications for further optimization and understanding, but also offers new directions for development of activated biochar. Copyright © 2016 Elsevier Ltd. All rights reserved.

A Global Covariance Descriptor for Nuclear Atypia Scoring in Breast Histopathology Images.

PubMed

Khan, Adnan Mujahid; Sirinukunwattana, Korsuk; Rajpoot, Nasir

2015-09-01

Nuclear atypia scoring is a diagnostic measure commonly used to assess tumor grade of various cancers, including breast cancer. It provides a quantitative measure of deviation in visual appearance of cell nuclei from those in normal epithelial cells. In this paper, we present a novel image-level descriptor for nuclear atypia scoring in breast cancer histopathology images. The method is based on the region covariance descriptor that has recently become a popular method in various computer vision applications. The descriptor in its original form is not suitable for classification of histopathology images as cancerous histopathology images tend to possess diversely heterogeneous regions in a single field of view. Our proposed image-level descriptor, which we term as the geodesic mean of region covariance descriptors, possesses all the attractive properties of covariance descriptors lending itself to tractable geodesic-distance-based k-nearest neighbor classification using efficient kernels. The experimental results suggest that the proposed image descriptor yields high classification accuracy compared to a variety of widely used image-level descriptors.

Separation and characterization of silybin, isosilybin, silydianin and silychristin in milk thistle extract by liquid chromatography-electrospray tandem mass spectrometry.

PubMed

Lee, James I; Hsu, Bih H; Wu, Di; Barrett, Jeffrey S

2006-05-26

A selective and sensitive liquid chromatography/tandem mass spectrometry (LC/MS/MS) method has been developed for the characterization of silymarin in commercially available milk thistle extract. In this study, six main active constituents, including silydianin, silychristin, diastereomers of silybin (silybin A and B) and diastereomers of isosilybin (isosilybin A and B) in silymarin, were completely separated on a YMC ODS-AQ HPLC column using a gradient mobile phase system comprised of ammonium acetate and methanol/water/formic acid. Identification and characterization of the major constituents were based not only on the product ion scan, which provided unique fragmentation information of a selected molecular ion, but also on the specific fragmentation of multiple reaction monitoring (MRM) data, which confirmed the retention times of LC chromatographic peaks. The method was applied in the analysis of human plasma samples in the presence of silymarin and appeared to be suitable for the pharmacokinetic studies in which the discrimination of silymarin constituents is essential.

Sensitive methods for the titrimetric micro-determination of biological calcium and magnesium

PubMed Central

Beale, R. N.; Bostrom, J. O.

1963-01-01

New reagents containing high concentrations of urea are developed for micro-titration of calcium and magnesium, with ethylenediamine tetra-acetic acid (E.D.T.A.) as titrant and Corinth Ca (Plasmocorinth B) as indicator. Magnesium is determined as the difference between calcium plus magnesium and calcium. Quantitative aspects are studied, and accurate titration of untreated serum or urine is believed to be possible; precision is satisfactory. The methods are simple, robust, and suitable for routine use. Normal ranges are established for serum from blood donors of each sex. The mean serum calcium level for women is found to be lower than for men, while the mean magnesium contents are approximately the same. The latter appear to be somewhat lower than values found by flame emission spectrophotometry; in very good agreement with a mean value for plasma obtained by flame absorption spectrophotometry; and intermediate when compared with the values obtained by two other titrimetric procedures. PMID:13969919

On the properties of energy stable flux reconstruction schemes for implicit large eddy simulation

NASA Astrophysics Data System (ADS)

Vermeire, B. C.; Vincent, P. E.

2016-12-01

We begin by investigating the stability, order of accuracy, and dispersion and dissipation characteristics of the extended range of energy stable flux reconstruction (E-ESFR) schemes in the context of implicit large eddy simulation (ILES). We proceed to demonstrate that subsets of the E-ESFR schemes are more stable than collocation nodal discontinuous Galerkin methods recovered with the flux reconstruction approach (FRDG) for marginally-resolved ILES simulations of the Taylor-Green vortex. These schemes are shown to have reduced dissipation and dispersion errors relative to FRDG schemes of the same polynomial degree and, simultaneously, have increased Courant-Friedrichs-Lewy (CFL) limits. Finally, we simulate turbulent flow over an SD7003 aerofoil using two of the most stable E-ESFR schemes identified by the aforementioned Taylor-Green vortex experiments. Results demonstrate that subsets of E-ESFR schemes appear more stable than the commonly used FRDG method, have increased CFL limits, and are suitable for ILES of complex turbulent flows on unstructured grids.

The question of organ procurement: beyond charity.

PubMed

Kreis, Henri

2005-07-01

Over the past 15 years, the shortage of organs for transplantation has worsened. This has forced clinicians to review alternative approaches to organ procurement. These new approaches, however, may have serious implications both for patients and for society as a whole. Ever since the first cadaver organs were used for transplantation, organ procurement has relied on the altruism and goodwill of donors. It now appears that this 40-year-old policy is proving unsuccessful. In order to increase the availability of suitable organs and allow cadaver organ transplantation to continue, it is time to consider new strategies other than donation. Among all the potential methods of organ procurement, including donation, abandonment, sale and societal appropriation, only the latter has never been ethically discussed or implemented. This article considers a variant of this approach defined as 'conditional societal appropriation' as an ethically acceptable possibility. It has the potential to become the principle method for obtaining the necessary organs for transplantation in the near future.

Evaluation of Iron Loss in Interior Permanent Magnet Synchronous Motor with Consideration of Rotational Field

NASA Astrophysics Data System (ADS)

Ma, Lei; Sanada, Masayuki; Morimoto, Shigeo; Takeda, Yoji; Kaido, Chikara; Wakisaka, Takeaki

Loss evaluation is an important issue in the design of electrical machines. Due to the complicate structure and flux distribution, it is difficult to predict the iron loss in the machines exactly. This paper studies the iron loss in interior permanent magnet synchronous motors based on the finite element method. The iron loss test data of core material are used in the fitting of the hysteresis and eddy current loss constants. For motors in practical operation, additional iron losses due to the appearance of rotation of flux density vector and harmonic flux density distribution makes the calculation data deviates from the measured ones. Revision is made to account for these excess iron losses which exist in the practical operating condition. Calculation results show good consistence with the experimental ones. The proposed method provides a possible way to predict the iron loss of the electrical machine with good precision, and may be helpful in the selection of the core material which is best suitable for a certain machine.

A study of radioactivity in modern stream gravels and its possible application as a prospecting method

USGS Publications Warehouse

Chew, Randall T.

1955-01-01

Traverses along some streams of the Colorado Plateau in areas known to contain minable uranium deposits show that anomalous radiation in the stream gravels can be detected with a suitable counter downstream from the deposits. The amount of radiation is influenced by the size of the uranium deposit, the size of the drainage area of the stream, the grain size of the sediments, and the lithology of the rocks over which the stream flows. The spacing of the stations where readings are taken is controlled by the size of the stream, and special readings are also taken directly downstream from important tributaries. An anomaly is empirically defined as a 10 percent rise over background. Radioactive material from large uranium deposits has been detected as much as 1 mile downstream. Radioactive material from smaller deposits is detachable over shorter distances. The method is slow but appears to be a useful prospecting tool under restricted conditions.

Urinary trace element concentrations in environmental settings: is there a value for systematic creatinine adjustment or do we introduce a bias?

PubMed

Hoet, Perrine; Deumer, Gladys; Bernard, Alfred; Lison, Dominique; Haufroid, Vincent

2016-01-01

Systematic creatinine adjustment of urinary concentrations of biomarkers has been a challenge over the past years because the assumption of a constant creatinine excretion rate appears erroneous and the issue of overadjustment has recently emerged. This study aimed at determining whether systematic creatinine adjustment is to be recommended for urinary concentrations of trace elements (TEs) in environmental settings. Paired 24-h collection and random spot urine samples (spotU) were obtained from 39 volunteers not occupationally exposed to TEs. Four models to express TEs concentration in spotU were tested to predict the 24-h excretion rate of these TEs (TEμg/24h) considered as the gold standard reference: absolute concentration (TEμg/l); ratio to creatinine (TEμg/gcr); TEμg/gcr adjusted to creatinine (TEμg/gcr-adj); and concentration adjusted to specific gravity (TEμg/l-SG). As, Ba, Cd, Co, Cr, Cu, Hg, Li, Mo, Ni, Pb, Sn, Sb, Se, Te, V and Zn were analyzed by inductively coupled argon plasma mass spectrometry. There was no single pattern of relationship between urinary TEs concentrations in spotU and TEμg/24h. TEμg/l predicted TEμg/24h with an explained variance ranging from 0 to 60%. Creatinine adjustment improved the explained variance by an additional 5 to ~60% for many TEs, but with a risk of overadjustment for the most of them. This issue could be addressed by adjusting TE concentrations on the basis of the regression coefficient of the relationship between TEμg/gcr and creatinine concentration. SG adjustment was as suitable as creatinine adjustment to predict TEμg/24h with no SG-overadjustment (except V). Regarding Cd, Cr, Cu, Ni and Te, none of the models were found to reflect TEμg/24h. In the context of environmental exposure, systematic creatinine adjustment is not recommended for urinary concentrations of TEs. SG adjustment appears to be a more reliable alternative. For some TEs, however, neither methods appear suitable.

Whole body cleaning agent containing N-acyltaurate

NASA Technical Reports Server (NTRS)

Lentsch, Steven E. (Inventor)

1992-01-01

The subject invention relates to a human cleansing agent particularly suitable for use in long duration spaceflight and to a method of bathing with the agent. The agent of the subject invention is in the form of a paste having a pH of 5.0 to 7.9 which comprises an acyltaurate, a skin conditioner, a hair conditioner, and a preservative. More specifically, it includes sodium N-coconut acid-N-methyl taurate, in combination with soybean lecithin, polyquaternium 16, and formalin. This particular combination satisfies the following objectives: (1) that it be usable with a minimum amount of water per shower (approximately 1 gallon); (2) that it be easily separated from the water for purposes of water reclamation; (3) that it be pH compatible with skin and hair; (4) that it rinse well in deionized water; (5) that it be mild to skin and eyes; (6) that it effectively clean both skin and hair; (7) that it be suitable for use in zero gravity; and (8) that it provide ease of combing of wet and dry hair. The method of the invention includes the steps of wetting the skin and hair with a small quantity of water, lathering the skin with the paste, rinsing the lather from the skin and hair with a small quantity of water to produce a rinse water containing the cleansing agent, defoaming the rinse water, and supplying the defoamed rinse water to a water reclamation unit for recycling the water. The novelty of the invention appears to lie in the particular formulation of the cleansing agent and its method of use which provide optimal results under the given constraints and objectives.

The classification of normal screening mammograms

NASA Astrophysics Data System (ADS)

Ang, Zoey Z. Y.; Rawashdeh, Mohammad A.; Heard, Robert; Brennan, Patrick C.; Lee, Warwick; Lewis, Sarah J.

2016-03-01

Rationale and objectives: To understand how breast screen readers classify the difficulty of normal screening mammograms using common lexicon describing normal appearances. Cases were also assessed on their suitability for a single reader strategy. Materials and Methods: 15 breast readers were asked to interpret a test set of 29 normal screening mammogram cases and classify them by rating the difficulty of the case on a five-point Likert scale, identifying the salient features and assessing their suitability for single reading. Using the False Positive Fractions from a previous study, the 29 cases were classified into 10 "low", 10 "medium" and nine "high" difficulties. Data was analyzed with descriptive statistics. Spearman's correlation was used to test the strength of association between the difficulty of the cases and the readers' recommendation for single reading strategy. Results: The ratings from readers in this study corresponded to the known difficulty level of cases for the 'low' and 'high' difficulty cases. Uniform ductal pattern and density, symmetrical mammographic features and the absence of micro-calcifications were the main reasons associated with 'low' difficulty cases. The 'high' difficulty cases were described as having `dense breasts'. There was a statistically significant negative correlation between the difficulty of the cases and readers' recommendation for single reading (r = -0.475, P = 0.009). Conclusion: The findings demonstrated potential relationships between certain mammographic features and the difficulty for readers to classify mammograms as 'normal'. The standard Australian practice of double reading was deemed more suitable for most cases. There was an inverse moderate association between the difficulty of the cases and the recommendations for single reading.

An overview of international literature from cystic fibrosis registries 2. Neonatal screening and nutrition/growth.

PubMed

Salvatore, Donatello; Buzzetti, Roberto; Baldo, Ermanno; Forneris, Maria Pia; Lucidi, Vincenzina; Manunza, Daniela; Marinelli, Italo; Messore, Barbara; Neri, Anna Silvia; Raia, Valeria; Furnari, Maria Lucia; Mastella, Gianni

2010-03-01

This is the second article related to a review of the literature based on data from national cystic fibrosis (CF) registries up to June 2008 and covering a total of 115 studies. It focuses on two topics: neonatal screening (NS) and nutritional status, with particular reference to growth. Ten papers meeting the inclusion criteria were found on the topic of NS and its impact on the course of the disease, and were analyzed according to a dedicated grid. The issue of nutrition was addressed by 14 studies, analyzed according to similar criteria. Most of the studies report benefits of early diagnosis by NS, albeit to variable degrees. The benefits were assessed in terms of better nutritional status and growth, but also in terms of lower overall morbidity rate as compared to subjects diagnosed by symptoms. The main biases of these studies, which partly undermine the validity of their results, are also analyzed. A part of our analysis on nutrition/growth is dedicated to the identification of the most suitable parameters to define malnutrition: in children older than two years the body mass index percentile (BMIp) appears to be the most sensitive and significantly associated with respiratory function. Better nutritional status and satisfactory growth appear to be associated with better lung function and lower risk of death. The relationship between nutritional status and socio-economic status is also of interest. CF registry studies support the outcome of cohort observational studies i.e. that pre-symptomatic early diagnosis is beneficial, especially in terms of nutritional status and growth. Studies on nutrition indicate that good nutritional status is associated with better respiratory function and prognosis. Regarding methods, the need emerged to manage potential biases of this kind of non randomized studies, resorting to suitable statistical techniques, such as matching and stratification and, above all, to multivariate methods able to provide estimates adjusted for the main covariates tested. Copyright (c) 2009 European Cystic Fibrosis Society. Published by Elsevier B.V. All rights reserved.

Influence of environmental variables in the efficiency of phage therapy in aquaculture.

PubMed

Silva, Yolanda J; Costa, Liliana; Pereira, Carla; Cunha, Ângela; Calado, Ricardo; Gomes, Newton C M; Almeida, Adelaide

2014-09-01

Aquaculture facilities worldwide continue to experience significant economic losses because of disease caused by pathogenic bacteria, including multidrug-resistant strains. This scenario drives the search for alternative methods to inactivate pathogenic bacteria. Phage therapy is currently considered as a viable alternative to antibiotics for inactivation of bacterial pathogens in aquaculture systems. While phage therapy appears to represent a useful and flexible tool for microbiological decontamination of aquaculture effluents, the effect of physical and chemical properties of culture waters on the efficiency of this technology has never been reported. The present study aimed to evaluate the effect of physical and chemical properties of aquaculture waters (e.g. pH, temperature, salinity and organic matter content) on the efficiency of phage therapy under controlled experimental conditions in order to provide a basis for the selection of the most suitable protocol for subsequent experiments. A bioluminescent genetically transformed Escherichia coli was selected as a model microorganism to monitor real-time phage therapy kinetics through the measurement of bioluminescence, thus avoiding the laborious and time-consuming conventional method of counting colony-forming units (CFU). For all experiments, a bacterial concentration of ≈ 10(5) CFU ml(-1) and a phage concentration of ≈ 10(6-8) plaque forming unit ml(-1) were used. Phage survival was not significantly affected by the natural variability of pH (6.5-7.4), temperature (10-25 °C), salinity (0-30 g NaCl l(-1) ) and organic matter concentration of aquaculture waters in a temperate climate. Nonetheless, the efficiency of phage therapy was mostly affected by the variation of salinity and organic matter content. As the effectiveness of phage therapy increases with water salt content, this approach appears to be a suitable choice for marine aquaculture systems. The success of phage therapy may also be enhanced in non-marine systems through the addition of salt, whenever this option is feasible and does not affect the survival of aquatic species being cultured. © 2013 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

Oligomeric cationic polymethacrylates: a comparison of methods for determining molecular weight.

PubMed

Locock, Katherine E S; Meagher, Laurence; Haeussler, Matthias

2014-02-18

This study compares three common laboratory methods, size-exclusion chromatography (SEC), (1)H nuclear magnetic resonance (NMR), and matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF), to determine the molecular weight of oligomeric cationic copolymers. The potential bias for each method was examined across a series of polymers that varied in molecular weight and cationic character (both choice of cation (amine versus guanidine) and relative proportion present). SEC was found to be the least accurate, overestimating Mn by an average of 140%, owing to the lack of appropriate cationic standards available, and the complexity involved in estimating the hydrodynamic volume of copolymers. MALDI-TOF approximated Mn well for the highly monodisperse (Đ < 1.1), low molecular weight (degree of polymerization (DP) <50) species but appeared unsuitable for the largest polymers in the series due to the mass bias associated with the technique. (1)H NMR was found to most accurately estimate Mn in this study, differing to theoretical values by only 5.2%. (1)H NMR end-group analysis is therefore an inexpensive and facile, primary quantitative method to estimate the molecular weight of oliogomeric cationic polymethacrylates if suitably distinct end-groups signals are present in the spectrum.

Investigation of the accuracy of breast tissue segmentation methods for the purpose of developing breast deformation models for use in adaptive radiotherapy

NASA Astrophysics Data System (ADS)

Juneja, P.; Harris, E. J.; Evans, P. M.

2014-03-01

Realistic modelling of breast deformation requires the breast tissue to be segmented into fibroglandular and fatty tissue and assigned suitable material properties. There are a number of breast tissue segmentation methods proposed and used in the literature. The purpose of this study was to validate and compare the accuracy of various segmentation methods and to investigate the effect of the tissue distribution on the segmentation accuracy. Computed tomography (CT) data for 24 patients, both in supine and prone positions were segmented into fibroglandular and fatty tissue. The segmentation methods explored were: physical density thresholding; interactive thresholding; fuzzy c-means clustering (FCM) with three classes (FCM3) and four classes (FCM4); and k-means clustering. Validation was done in two-stages: firstly, a new approach, supine-prone validation based on the assumption that the breast composition should appear the same in the supine and prone scans was used. Secondly, outlines from three experts were used for validation. This study found that FCM3 gave the most accurate segmentation of breast tissue from CT data and that the segmentation accuracy is adversely affected by the sparseness of the fibroglandular tissue distribution.

Shape classification of wear particles by image boundary analysis using machine learning algorithms

NASA Astrophysics Data System (ADS)

Yuan, Wei; Chin, K. S.; Hua, Meng; Dong, Guangneng; Wang, Chunhui

2016-05-01

The shape features of wear particles generated from wear track usually contain plenty of information about the wear states of a machinery operational condition. Techniques to quickly identify types of wear particles quickly to respond to the machine operation and prolong the machine's life appear to be lacking and are yet to be established. To bridge rapid off-line feature recognition with on-line wear mode identification, this paper presents a new radial concave deviation (RCD) method that mainly involves the use of the particle boundary signal to analyze wear particle features. Signal output from the RCDs subsequently facilitates the determination of several other feature parameters, typically relevant to the shape and size of the wear particle. Debris feature and type are identified through the use of various classification methods, such as linear discriminant analysis, quadratic discriminant analysis, naïve Bayesian method, and classification and regression tree method (CART). The average errors of the training and test via ten-fold cross validation suggest CART is a highly suitable approach for classifying and analyzing particle features. Furthermore, the results of the wear debris analysis enable the maintenance team to diagnose faults appropriately.

Automated respiratory sinus arrhythmia measurement: Demonstration using executive function assessment.

PubMed

Hegarty-Craver, Meghan; Gilchrist, Kristin H; Propper, Cathi B; Lewis, Gregory F; DeFilipp, Samuel J; Coffman, Jennifer L; Willoughby, Michael T

2017-08-08

Respiratory sinus arrhythmia (RSA) is a quantitative metric that reflects autonomic nervous system regulation and provides a physiological marker of attentional engagement that supports cognitive and affective regulatory processes. RSA can be added to executive function (EF) assessments with minimal participant burden because of the commercial availability of lightweight, wearable electrocardiogram (ECG) sensors. However, the inclusion of RSA data in large data collection efforts has been hindered by the time-intensive processing of RSA. In this study we evaluated the performance of an automated RSA-scoring method in the context of an EF study in preschool-aged children. The absolute differences in RSA across both scoring methods were small (mean RSA differences = -0.02-0.10), with little to no evidence of bias for the automated relative to the hand-scoring approach. Moreover, the relative rank-ordering of RSA across both scoring methods was strong (rs = .96-.99). Reliable changes in RSA from baseline to the EF task were highly similar across both scoring methods (96%-100% absolute agreement; Kappa = .83-1.0). On the basis of these findings, the automated RSA algorithm appears to be a suitable substitute for hand-scoring in the context of EF assessment.

The Tree Theme Method in psychosocial occupational therapy: a case study.

PubMed

Gunnarsson, A Birgitta; Jansson, Jan-Ake; Eklund, Mona

2006-12-01

This study aimed to describe the Tree Theme Method (TTM) as a method for intervention in psychosocial occupational therapy. The TTM is based on theories concerning creative activities and occupational storytelling and story making. In order to exemplify the method a case study of a treatment process with follow up was undertaken. The participant was a female client suffering from anxiety and depression. During an interview the client painted symbolic trees on five different occasions with specific variations of the tree theme: a tree symbolizing her present life, her childhood, adolescence, adulthood, and, finally, a tree representing her future. The trees were used as starting points for the client to tell her life story. The intention was that she would find new strategies for how to change her daily life. Three years later there was a follow up stage where the client painted new trees and told her story. Some life themes were identified. The TTM appears suitable for intervention in psychosocial occupational therapy. In future studies the TTM should be subjected to evaluation research based on several clients in order to develop a deeper understanding of the process and what kind of results changes in the TTM intervention may provide.

Distribution, abundance, and spawning season and grounds of the kiyi, Leucichthys kiyi Koelz, in Lake Michigan

USGS Publications Warehouse

Hile, Ralph; Deason, Hilary J.

1947-01-01

The depth of water on known spawning grounds (all in southern Lake Michigan) was 57.5 to 84 fathoms. There is evidence that the kiyi may spawn in more than 90 fathoms. Spawning appears to be widespread throughout waters of suitable depth.

Rethinking Global Engagement - The Requirement for Knowledge Before Action

DTIC Science & Technology

2005-06-01

nevertheless cautions against irrational exuberance ; the REC is suitable for some important reasons and should be implemented, but it is not a replacement for...efforts… have floundered (p. 186).” The exuberant enthusiasm for James Bond-like activities appears enduring in both the official and popular mind

For the Classroom--The Five Signs of Death: Cold Water Camouflage.

ERIC Educational Resources Information Center

Lin, Leslie

1981-01-01

Outlines a classroom science activity suitable for elementary through adult levels demonstrating that coldwater submergence may cause some people to appear dead when they are not. Includes a description of several activities which exhibit the signs of coldwater camouflage, materials needed, and discussion topics. (DS)

Soil suitability for hardwoods in Coastal Plains

Treesearch

W. M. Broadfoot; J. S. McKnight

1962-01-01

The Coastal Plain soil area occupies the major portion of Mississippi east of the Delta and Loess areas. In general, the soils are sandy, acid, and lacking in natural fertility, but on the alluvial soils moisture and drainage relations appear sufficient to support good growth of some tree species.

Student Satisfaction Scale Development and Application for Sport Management in China

ERIC Educational Resources Information Center

Liu, Liu; Wang, Yong-Shun; Wu, Tung-Ju

2017-01-01

Student satisfaction is a primary indicator for college and university organizational self-assessment in European and American countries. Professional sport universities are the major institution cultivating sports talents in China. Nevertheless, it appears the problem in past years that the talent cultivation and management is not suitable for…

Natural regeneration of eastern hemlock: a review

Treesearch

Daniel L. Goerlich; Ralph D. Nyland

2000-01-01

Successful regeneration of eastern hemlock involves a complex biophysical process that commonly spans many years. Critical factors include a reliable source of seed, a suitable seedbed, a partially shaded environment, and several years of favorable moisture. Surface scarification appears critical as a means of site preparation. Even then, young hemlocks grow slowly,...

Appearance of gauge structure in simple dynamical systems

NASA Technical Reports Server (NTRS)

Wilczek, F.; Zee, A.

1984-01-01

By generalizing a construction of Berry and Simon, it is shown that non-Abelian gauge fields arise in the adiabatic development of simple quantum mechanical systems. Characteristics of the gauge fields are related to energy splittings, which may be observable in real systems. Similar phenomena are found for suitable classical systems.

Assessing coastal reclamation suitability based on a fuzzy-AHP comprehensive evaluation framework: A case study of Lianyungang, China.

PubMed

Feng, Lan; Zhu, Xiaodong; Sun, Xiang

2014-12-15

Coastal reclamation suitability evaluation (CRSE) is a difficult, complex and protracted process requiring the evaluation of many different criteria. In this paper, an integrated framework employing a fuzzy comprehensive evaluation method and analytic hierarchy process (AHP) was applied to the suitability evaluation for coastal reclamation for future sustainable development in the coastal area of Lianyungang, China. The evaluation results classified 6.63%, 22.99%, 31.59% and 38.79% of the coastline as suitable, weakly suitable, unsuitable and forbidden, respectively. The evaluation results were verified by the marine pollution data and highly consistent with the water quality status. The fuzzy-AHP comprehensive evaluation method (FACEM) was found to be suitable for the CRSE. This CRSE can also be applied to other coastal areas in China and thereby be used for the better management of coastal reclamation and coastline protection projects. Copyright © 2014 Elsevier Ltd. All rights reserved.

Attention Deficit Hyperactivity Disorder: Is There an App for That? Suitability Assessment of Apps for Children and Young People With ADHD

PubMed Central

Parker, Jack; Robertson, Naomi; Harpin, Valerie

2017-01-01

Background Attention-deficit/hyperactivity disorder (ADHD) is a complex highly comorbid disorder, which can have a huge impact on those with ADHD, their family, and the community around them. ADHD is currently managed using pharmacological and nonpharmacological interventions. However, with advances in technology and an increase in the use of mobile apps, managing ADHD can be augmented using apps specifically designed for this population. However, little is known regarding the suitability and usability of currently available apps. Objective The aim of this study was to explore the suitability of the top 10 listed apps for children and young people with ADHD and clinicians who work with them. It is hypothesized that mobile apps designed for this population could be more suitably designed for this population. Methods The top 10 listed apps that are specifically targeted toward children and young people with ADHD in the United Kingdom were identified via the Google Play (n=5) and iTunes store (n=5). Interviews were then undertaken with 5 clinicians who specialize in treating this population and 5 children and young people with ADHD themselves, to explore their opinions of the 10 apps identified and what they believe the key components are for apps to be suitable for this population. Results Five themes emerged from clinician and young people interviews: the accessibility of the technology, the importance of relating to apps, addressing ADHD symptoms and related difficulties, age appropriateness, and app interaction. Three additional themes emerged from the clinician interviews alone: monitoring symptoms, side effects and app effect on relationships, and the impact of common comorbid conditions. The characteristics of the apps did not appear to match well with the views of our sample. Conclusions These findings suggest that the apps may not be suitable in meeting the complex needs associated with this condition. Further research is required to explore the value of apps for children and young people with ADHD and their families and, in particular, any positive role for apps in the management of ADHD in this age group. A systematic review on how technology can be used to engage this population and how it can be used to help them would be a useful way forward. This could be the platform to begin exploring the use of apps further. PMID:28978497

Advanced high temperature static strain sensor development

NASA Technical Reports Server (NTRS)

Hulse, C. O.; Stetson, K. A.; Grant, H. P.; Jameikis, S. M.; Morey, W. W.; Raymondo, P.; Grudkowski, T. W.; Bailey, R. S.

1986-01-01

An examination was made into various techniques to be used to measure static strain in gas turbine liners at temperatures up to 1150 K (1600 F). The methods evaluated included thin film and wire resistive devices, optical fibers, surface acoustic waves, the laser speckle technique with a heterodyne readout, optical surface image and reflective approaches and capacitive devices. A preliminary experimental program to develop a thin film capacitive device was dropped because calculations showed that it would be too sensitive to thermal gradients. In a final evaluation program, the laser speckle technique appeared to work well up to 1150 K when it was used through a relatively stagnant air path. The surface guided acoustic wave approach appeared to be interesting but to require too much development effort for the funds available. Efforts to develop a FeCrAl resistive strain gage system were only partially successful and this part of the effort was finally reduced to a characterization study of the properties of the 25 micron diameter FeCrAl (Kanthal A-1) wire. It was concluded that this particular alloy was not suitable for use as the resistive element in a strain gage above about 1000 K.

The Use of Tunnel Muck as Industrial Raw Material: Two Case-Studies

NASA Astrophysics Data System (ADS)

Marini, P.; Bellopede, R.

2013-03-01

The re-use of rock as an industrial material requires more treatments than those foreseen for the reuse of muck as an aggregate for concrete and for road construction. The treatments always start with comminution, which has the goal of liberating the rock-forming minerals. Liberation is achieved with the appearance of grains which are composed of only one mineral. The subsequent treatment steps are based on the physical-mechanical-chemical properties of the different minerals, that is, density, magnetic susceptibility, wettability etc. Magnetic separation and flotation, the two techniques examined in this research, are the two most common techniques used in industrial mineral production plants. The mucks that were analysed are from the Omegna and Brennero tunnels, both of which are granitic rocks with different textures. From the analysis and comparison of the preliminary treatment results, it has been possible to optimise the treatment method. Petrographic, mineralogic and firing tests have been conducted to evaluate the obtained results. High-gradient magnetic separation (HGMS) on defined grain sizes appears to be suitable to obtain a product with a high feldspar-quartz content which could be used in the ceramic field.

Advanced high temperature static strain sensor development

NASA Astrophysics Data System (ADS)

Hulse, C. O.; Stetson, K. A.; Grant, H. P.; Jameikis, S. M.; Morey, W. W.; Raymondo, P.; Grudkowski, T. W.; Bailey, R. S.

1986-08-01

An examination was made into various techniques to be used to measure static strain in gas turbine liners at temperatures up to 1150 K (1600 F). The methods evaluated included thin film and wire resistive devices, optical fibers, surface acoustic waves, the laser speckle technique with a heterodyne readout, optical surface image and reflective approaches and capacitive devices. A preliminary experimental program to develop a thin film capacitive device was dropped because calculations showed that it would be too sensitive to thermal gradients. In a final evaluation program, the laser speckle technique appeared to work well up to 1150 K when it was used through a relatively stagnant air path. The surface guided acoustic wave approach appeared to be interesting but to require too much development effort for the funds available. Efforts to develop a FeCrAl resistive strain gage system were only partially successful and this part of the effort was finally reduced to a characterization study of the properties of the 25 micron diameter FeCrAl (Kanthal A-1) wire. It was concluded that this particular alloy was not suitable for use as the resistive element in a strain gage above about 1000 K.

Chemometric compositional analysis of phenolic compounds in fermenting samples and wines using different infrared spectroscopy techniques.

PubMed

Aleixandre-Tudo, Jose Luis; Nieuwoudt, Helene; Aleixandre, Jose Luis; du Toit, Wessel

2018-01-01

The wine industry requires reliable methods for the quantification of phenolic compounds during the winemaking process. Infrared spectroscopy appears as a suitable technique for process control and monitoring. The ability of Fourier transform near infrared (FT-NIR), attenuated total reflectance mid infrared (ATR-MIR) and Fourier transform infrared (FT-IR) spectroscopies to predict compositional phenolic levels during red wine fermentation and aging was investigated. Prediction models containing a large number of samples collected over two vintages from several industrial fermenting tanks as well as wine samples covering a varying number of vintages were validated. FT-NIR appeared as the most accurate technique to predict the phenolic content. Although slightly less accurate models were observed, ATR-MIR and FT-IR can also be used for the prediction of the majority of phenolic measurements. Additionally, the slope and intercept test indicated a systematic error for the three spectroscopies which seems to be slightly more pronounced for HPLC generated phenolics data than for the spectrophotometric parameters. However, the results also showed that the predictions made with the three instruments are statistically comparable. The robustness of the prediction models was also investigated and discussed. Copyright © 2017 Elsevier B.V. All rights reserved.

Management of a typhoon-induced landslide in Otomura (Japan)

NASA Astrophysics Data System (ADS)

Fujisawa, Kazunori; Marcato, Gianluca; Nomura, Yasuhiro; Pasuto, Alessandro

2010-12-01

Late in January 2004 slope instability evidence such as cracks and subsidence appeared on a retaining wall along National Highway 168, near Otomura (Nara Prefecture, Japan). This road plays a strategic role as a long distance route for passenger vehicles and trucks, therefore detailed investigations and constant surveillance have to be carried out in order to manage the induced risk situations. Six months later, on August 10th, a large landslide occurred due to heavy rainfalls related to typhoons #10 and #11 that hit Japan on the first week of August. Field and aerial surveys of the site were carried out soon after the appearance of the first geomorphologic evidence of landslide movements, and a monitoring system was immediately set up. Landslide displacements have been measured since the early stage of movement and road traffic was strictly controlled in order to minimize possible damage. This paper illustrates the effects of landslide activation and the investigations carried out in order to assess landslide hazard and predict the time of failure. Suitable methods for risk management oriented to increase the public safety and including risk control and crisis mitigation acts are also discussed.

Cellular uptake and intracellular fate of engineered nanoparticles: a review on the application of imaging techniques.

PubMed

Tantra, Ratna; Knight, Alex

2011-09-01

The use of imaging tools to probe nanoparticle-cell interactions will be crucial to elucidating the mechanisms of nanoparticle-induced toxicity. Of particular interest are mechanisms associated with cell penetration, translocation and subsequent accumulation inside the cell, or in cellular compartments. The objective of the present paper is to review imaging techniques that have been previously used in order to assess such interactions, and new techniques with the potential to be useful in this area. In order to identify the most suitable techniques, they were evaluated and matched against a list of evaluation criteria. We conclude that limitations exist with all of the techniques and the ultimate choice will thus depend on the needs of end users, and their particular application. The state-of-the-art techniques appear to have the least limitations, despite the fact that they are not so well established and still far from being routine. For example, super-resolution microscopy techniques appear to have many advantages for understanding the details of the interactions between nanoparticles and cells. Future research should concentrate on further developing or improving such novel techniques, to include the development of standardized methods and appropriate reference materials.

Using Geographic Information Systems to Determine Site Suitability for a Low-Level Radioactive Waste Storage Facility.

PubMed

Wilson, Charles A; Matthews, Kennith; Pulsipher, Allan; Wang, Wei-Hsung

2016-02-01

Radioactive waste is an inevitable product of using radioactive material in education and research activities, medical applications, energy generation, and weapons production. Low-level radioactive waste (LLW) makes up a majority of the radioactive waste produced in the United States. In 2010, over two million cubic feet of LLW were shipped to disposal sites. Despite efforts from several states and compacts as well as from private industry, the options for proper disposal of LLW remain limited. New methods for quickly identifying potential storage locations could alleviate current challenges and eventually provide additional sites and allow for adequate regional disposal of LLW. Furthermore, these methods need to be designed so that they are easily communicated to the public. A Geographic Information Systems (GIS) based method was developed to determine suitability of potential LLW disposal (or storage) sites. Criteria and other parameters of suitability were based on the Code of Federal Regulation (CFR) requirements as well as supporting literature and reports. The resultant method was used to assess areas suitable for further evaluation as prospective disposal sites in Louisiana. Criteria were derived from the 10 minimum requirements in 10 CFR Part 61.50, the Nuclear Regulatory Commission's Regulatory Guide 0902, and studies at existing disposal sites. A suitability formula was developed permitting the use of weighting factors and normalization of all criteria. Data were compiled into GIS data sets and analyzed on a cell grid of approximately 14,000 cells (covering 181,300 square kilometers) using the suitability formula. Requirements were analyzed for each cell using multiple criteria/sub-criteria as well as surrogates for unavailable datasets. Additional criteria were also added when appropriate. The method designed in this project proved to be sufficient for initial screening tests in determining the most suitable areas for prospective disposal (or storage) sites. Cells above 90%, 95%, and 99% suitability include respectively 404, 88, and 4 cells suitable for further analysis. With these areas identified, the next step in siting a LLW storage facility would be on-site analysis using additional requirements as specified by relevant regulatory guidelines. The GIS based method provides an easy, economic, efficient and effective means in evaluating potential sites for LLW storage facilities where sufficient GIS data exist.

Using a Geographic Information System to Assess Site Suitability for Managed Aquifer Recharge using Stormwater Capture

NASA Astrophysics Data System (ADS)

Teo, E. K.; Harmon, R. E.; Beganskas, S.; Young, K. S.; Fisher, A. T.; Weir, W. B.; Lozano, S.

2015-12-01

We are completing a regional analysis of Santa Cruz and northern Monterey Counties, CA, to assess the conditions amenable to managed aquifer recharge using stormwater runoff. Communities and water supply agencies across CA are struggling to mitigate the ongoing drought and to develop secure and sustainable water supplies to support long-term municipal, agricultural, environmental and other needs. Enhanced storage of groundwater is an important part of this effort in many basins. This work is especially timely because of the recently enacted "Sustainable Groundwater Management Act" (SGMA), which requires the development of groundwater sustainability agencies and implementation of basin management plans in coming decades. Our analysis focuses specifically on the distributed collection of stormwater runoff, a water source that has typically been treated as a nuisance or waste, from drainages having an area on the order of 40-160 hectares. The first part of this project is a geographic information system (GIS) analysis using surface and subsurface data sets. Developing complete and accurate datasets across the study region required considerable effort to locate, assemble, co-register, patch, and reconcile information from many sources and scales. We have complete spatial coverage for surface data, but subsurface data is more limited in lateral extent. Sites that are most suitable for distributed stormwater capture supporting MAR have high soil infiltration capacity, are well-connected to an underlying aquifer with good transmissive and storage properties, and have space to receive MAR. Additional considerations include method of infiltration, slope, and land use and access. Based on initial consideration of surface data and slope, 7% of the complete study region appears to be "suitable or highly suitable" for MAR (in the top third of the rating system), but there is considerable spatial heterogeneity based on the distribution of shallow soils and bedrock geology.

Quantifying relationships between abundances of cold-water coral Lophelia pertusa and terrain features: A case study on the Norwegian margin

NASA Astrophysics Data System (ADS)

Tong, Ruiju; Purser, Autun; Guinan, Janine; Unnithan, Vikram; Yu, Jinsongdi; Zhang, Chengcheng

2016-03-01

An understanding of how terrain features influence abundance of a particular species greatly aids in the development of accurate predictive habitat suitability models. In this study, we investigated the observed seafloor coverage of cold-water coral Lophelia pertusa in relation to seabed topography at the Sotbakken and Røst Reefs on the Norwegian margin. The primary terrain features at the study sites are a SW-NE stretching mound at Sotbakken Reef and SW-NE running ridges at Røst Reef, located at depths of ~300-400 m and ~250-320 m respectively. Ship-borne multibeam bathymetry data, JAGO dive video data and JAGO positioning data were used in this study. Terrain variables were calculated at scales of 30 m, 90 m and 170 m based on the bathymetry data. Additionally, we investigated the relationships between the terrain variables at multiple scales using the Unweighted Pair Group Method. The observed L. pertusa coverage at both reefs was found to be significantly correlated with most investigated terrain variables, with correlations increasing in strength with increase in analysis scale, suggesting that large scale terrain features likely play an important role in influencing L. pertusa distribution. Small scale terrain variations appear less important in determining the suitability of a region of seafloor for L. pertusa colonization. We conclude that bathymetric position index and curvature, as well as seabed aspect, most strongly correlate with coral coverage, indicating that local topographic highs, with an orientation into inflowing bottom currents, are most suitable for L. pertusa habitation. These results indicate that developing habitat suitability models for L. pertusa will benefit from inclusion of particular key terrain variables (e.g. aspect, plan curvature, mean curvature and slope) and that these should ideally be computed at multiple spatial scales with a greater gap in scales than we used in this study, to maximize the inclusion of the key variables in the model whilst minimizing redundancy.

Selection and visualisation of outcome measures for complex post-acute acquired brain injury rehabilitation interventions

PubMed Central

Ford, Catherine Elaine Longworth; Malley, Donna; Bateman, Andrew; Clare, Isabel C.H.; Wagner, Adam P.; Gracey, Fergus

2016-01-01

Background Outcome measurement challenges rehabilitation services to select tools that promote stakeholder engagement in measuring complex interventions. Objectives To examine the suitability of outcome measures for complex post-acute acquired brain injury (ABI) rehabilitation interventions, report outcomes of a holistic, neuropsychological ABI rehabilitation program and propose a simple way of visualizing complex outcomes. Methods Patient/carer reported outcome measures (PROMS), experience measures (PREMS) and staff-rated measures were collected for consecutive admissions over 1 year to an 18-week holistic, neuropsychological rehabilitation programme at baseline, 18 weeks and 3- and 6-month follow-up. Results Engagement with outcome measurement was poorest for carers and at follow-up for all stakeholders. Dependence, abilities, adjustment, unmet needs, symptomatology including executive dysfunction, and self-reassurance showed improvements at 18 weeks. Adjustment, social participation, perceived health, symptomatology including dysexecutive difficulties, and anxiety were worse at baseline for those who did not complete rehabilitation, than those who did. A radar plot facilitated outcome visualization. Conclusions Engagement with outcome measurement was best when time and support were provided. Supplementing patient- with staff-rated and attendance measures may explain missing data and help quantify healthcare needs. The MPAI4, EBIQ and DEX-R appeared suitable measures to evaluate outcomes and distinguish those completing and not completing neuropsychological rehabilitation. PMID:27341362

High-Throughput Analytical Techniques for the Determination of the Residues of 653 Multiclass Pesticides and Chemical Pollutants in Tea, Part VII: A GC-MS, GC-MS/MS, and LC-MS/MS Study of the Degradation Profiles of Pesticide Residues in Green Tea.

PubMed

Chang, Qiao-Ying; Pang, Guo-Fang; Fan, Chun-Lin; Chen, Hui; Yang, Fang; Li, Jie; Wen, Bi-Fang

2016-11-01

GC-MS, GC-tandem MS (MS/MS), and LC-MS/MS were used to mathematically define the degradation profiles of pesticide residues in two field trials. Nineteen pesticides were studied in the first field trial and 11 in the second. The results of the field trials demonstrated that the degradation profiles of pesticide residues in green tea can be described with power functions to successfully estimate the amount of time, following pesticide application, pesticide residues appearing in tea in concentrations at and/or above the maximum residue limit (MRL) decrease to concentrations below the MRL. Stability tests on green tea samples stored at room temperature were conducted to determine whether pesticide-incurred green tea samples prepared according to the method used in the field trials would be suitable for the preparation of reference standards for laboratory-proficiency testing trials. This paper reports the results of a GC-MS, GC-MS/MS, and LC-MS/MS study, as well as the suitability of the samples prepared under these conditions for use as pesticide reference standards in tea analysis.

Hindered rotor models with variable kinetic functions for accurate thermodynamic and kinetic predictions

NASA Astrophysics Data System (ADS)

Reinisch, Guillaume; Leyssale, Jean-Marc; Vignoles, Gérard L.

2010-10-01

We present an extension of some popular hindered rotor (HR) models, namely, the one-dimensional HR (1DHR) and the degenerated two-dimensional HR (d2DHR) models, allowing for a simple and accurate treatment of internal rotations. This extension, based on the use of a variable kinetic function in the Hamiltonian instead of a constant reduced moment of inertia, is extremely suitable in the case of rocking/wagging motions involved in dissociation or atom transfer reactions. The variable kinetic function is first introduced in the framework of a classical 1DHR model. Then, an effective temperature and potential dependent constant is proposed in the cases of quantum 1DHR and classical d2DHR models. These methods are finally applied to the atom transfer reaction SiCl3+BCl3→SiCl4+BCl2. We show, for this particular case, that a proper accounting of internal rotations greatly improves the accuracy of thermodynamic and kinetic predictions. Moreover, our results confirm (i) that using a suitably defined kinetic function appears to be very adapted to such problems; (ii) that the separability assumption of independent rotations seems justified; and (iii) that a quantum mechanical treatment is not a substantial improvement with respect to a classical one.

Remote clinical decision-making: a clinician's definition.

PubMed

Brady, Mike; Northstone, Kate

2017-05-12

Aims Remote clinical decision-making (RCDM), commonly known as 'telephone triage' or 'hear and treat', describes clinicians' non-face-to-face involvement with patient care, and is an established strategy in UK ambulance services for managing increasing demand. However, there is no suitable definition of RCDM that fully explains the roles undertaken by clinicians in 999 hubs, or for its use as an ambulance quality indicator (AQI). The aim of this study, which is part of a larger evaluation of a new RCDM module in higher education, is to determine how clinicians define RCDM. Methods Three participants were asked, during semi-structured interviews, to define RCDM. The interviews were recorded, transcribed and thematically analysed. Results Clinicians do not focus on outcomes when defining RCDM, but on the efficacy of the process and the appropriateness of the determined outcome. Conclusion There is no precise description of the role of healthcare professionals in 999 clinical hubs, but there is a need for role clarity, for employees and organisations. The study questions the suitability of the definition of hear and treat as an AQI, as it does not appear to represent fully the various duties undertaken by 999 clinical hub healthcare professionals. More research is needed to consider the definition of RCDM in all its forms.

A Scale-up Approach for Film Coating Process Based on Surface Roughness as the Critical Quality Attribute.

PubMed

Yoshino, Hiroyuki; Hara, Yuko; Dohi, Masafumi; Yamashita, Kazunari; Hakomori, Tadashi; Kimura, Shin-Ichiro; Iwao, Yasunori; Itai, Shigeru

2018-04-01

Scale-up approaches for film coating process have been established for each type of film coating equipment from thermodynamic and mechanical analyses for several decades. The objective of the present study was to establish a versatile scale-up approach for film coating process applicable to commercial production that is based on critical quality attribute (CQA) using the Quality by Design (QbD) approach and is independent of the equipment used. Experiments on a pilot scale using the Design of Experiment (DoE) approach were performed to find a suitable CQA from surface roughness, contact angle, color difference, and coating film properties by terahertz spectroscopy. Surface roughness was determined to be a suitable CQA from a quantitative appearance evaluation. When surface roughness was fixed as the CQA, the water content of the film-coated tablets was determined to be the critical material attribute (CMA), a parameter that does not depend on scale or equipment. Finally, to verify the scale-up approach determined from the pilot scale, experiments on a commercial scale were performed. The good correlation between the surface roughness (CQA) and the water content (CMA) identified at the pilot scale was also retained at the commercial scale, indicating that our proposed method should be useful as a scale-up approach for film coating process.

Improving the recovery of qPCR-grade DNA from sludge and sediment.

PubMed

Bonot, Sébastien; Courtois, Sophie; Block, Jean-Claude; Merlin, Christophe

2010-08-01

DNA extraction is often considered as the limiting step of most molecular approaches in ecology and environmental microbiology. Ten existing DNA extraction protocols were compared for recovery of DNA from sludge and a modified version of the protocol described by Porteous et al. (Mol Ecol 6:787-791, 1997) was determined to be the best method for recovery of DNA suitable for PCR. In this respect, it appeared that the commonly used guanidine isothiocyanate could impair the quality of the extracted DNA unless its concentration is lowered. Second, conditioning the samples as liquors as opposed to pellets critically impacts the outcome of the extraction. The suitability of the modified Porteous protocol for quantitative PCR applications is demonstrated in a series of experiments showing the absence of interfering coextracted inhibitors and the linear correspondence between the concentrations of input target DNA and PCR product. Interestingly, it is also shown that the nature of the environmental matrices affects the recovery yield of both circular plasmids and chromosomal DNA, resulting in an apparent fluctuation of the plasmid copy number per cell. This means that quantitative data obtained by PCR remain comparable as long as they apply to an identical target sequence extracted from a similar environment and amplified under the same conditions.

Molecular Tools for the Detection of Nitrogen Cycling Archaea

PubMed Central

Rusch, Antje

2013-01-01

Archaea are widespread in extreme and temperate environments, and cultured representatives cover a broad spectrum of metabolic capacities, which sets them up for potentially major roles in the biogeochemistry of their ecosystems. The detection, characterization, and quantification of archaeal functions in mixed communities require Archaea-specific primers or probes for the corresponding metabolic genes. Five pairs of degenerate primers were designed to target archaeal genes encoding key enzymes of nitrogen cycling: nitrite reductases NirA and NirB, nitrous oxide reductase (NosZ), nitrogenase reductase (NifH), and nitrate reductases NapA/NarG. Sensitivity towards their archaeal target gene, phylogenetic specificity, and gene specificity were evaluated in silico and in vitro. Owing to their moderate sensitivity/coverage, the novel nirB-targeted primers are suitable for pure culture studies only. The nirA-targeted primers showed sufficient sensitivity and phylogenetic specificity, but poor gene specificity. The primers designed for amplification of archaeal nosZ performed well in all 3 criteria; their discrimination against bacterial homologs appears to be weakened when Archaea are strongly outnumbered by bacteria in a mixed community. The novel nifH-targeted primers showed high sensitivity and gene specificity, but failed to discriminate against bacterial homologs. Despite limitations, 4 of the new primer pairs are suitable tools in several molecular methods applied in archaeal ecology. PMID:23365509

A proposed configurable approach for recommendation systems via data mining techniques

NASA Astrophysics Data System (ADS)

Khedr, Ayman E.; Idrees, Amira M.; Hegazy, Abd El-Fatah; El-Shewy, Samir

2018-02-01

This study presents a configurable approach for recommendations which determines the suitable recommendation method for each field based on the characteristics of its data, the method includes determining the suitable technique for selecting a representative sample of the provided data. Then selecting the suitable feature weighting measure to provide a correct weight for each feature based on its effect on the recommendations. Finally, selecting the suitable algorithm to provide the required recommendations. The proposed configurable approach could be applied on different domains. The experiments have revealed that the approach is able to provide recommendations with only 0.89 error rate percentage.

[Study on ecological suitability regionalization of Eucommia ulmoides in Guizhou].

PubMed

Kang, Chuan-Zhi; Wang, Qing-Qing; Zhou, Tao; Jiang, Wei-Ke; Xiao, Cheng-Hong; Xie, Yu

2014-05-01

To study the ecological suitability regionalization of Eucommia ulmoides, for selecting artificial planting base and high-quality industrial raw material purchase area of the herb in Guizhou. Based on the investigation of 14 Eucommia ulmoides producing areas, pinoresinol diglucoside content and ecological factors were obtained. Using spatial analysis method to carry on ecological suitability regionalization. Meanwhile, combining pinoresinol diglucoside content, the correlation of major active components and environmental factors were analyzed by statistical analysis. The most suitability planting area of Eucommia ulmoides was the northwest of Guizhou. The distribution of Eucommia ulmoides was mainly affected by the type and pH value of soil, and monthly precipitation. The spatial structure of major active components in Eucommia ulmoides were randomly distributed in global space, but had only one aggregation point which had a high positive correlation in local space. The major active components of Eucommia ulmoides had no correlation with altitude, longitude or latitude. Using the spatial analysis method and statistical analysis method, based on environmental factor and pinoresinol diglucoside content, the ecological suitability regionalization of Eucommia ulmoides can provide reference for the selection of suitable planting area, artificial planting base and directing production layout.

Physical attractiveness biases in ratings of employment suitability: tracking down the "beauty is beastly" effect.

PubMed

Johnson, Stefanie K; Podratz, Kenneth E; Dipboye, Robert L; Gibbons, Ellie

2010-01-01

The "what is beautiful is good" heuristic suggests that physically attractive persons benefit from their attractiveness in a large range of situations, including perceptions of employment suitability. Conversely, the "beauty is beastly" effect suggests that attractiveness can be detrimental to women in certain employment contexts, although these findings have been less consistent than those for the "what is beautiful is good" effect. The current research seeks to uncover situations in which beauty might be detrimental for female applicants. In two studies, we found that attractiveness can be detrimental for women applying for masculine sex-typed jobs for which physical appearance is perceived as unimportant.

Alcohol Content in the 'Hyper-Reality' MTV Show 'Geordie Shore'.

PubMed

Lowe, Eden; Britton, John; Cranwell, Jo

2018-05-01

To quantify the occurrence of alcohol content, including alcohol branding, in the popular primetime television UK Reality TV show 'Geordie Shore' Series 11. A 1-min interval coding content analysis of alcohol content in the entire DVD Series 11 of 'Geordie Shore' (10 episodes). Occurrence of alcohol use, implied use, other alcohol reference/paraphernalia or branding was recorded. All categories of alcohol were present in all episodes. 'Any alcohol' content occurred in 78%, 'actual alcohol use' in 30%, 'inferred alcohol use' in 72%, and all 'other' alcohol references occurred in 59% of all coding intervals (ACIs), respectively. Brand appearances occurred in 23% of ACIs. The most frequently observed alcohol brand was Smirnoff which appeared in 43% of all brand appearances. Episodes categorized as suitable for viewing by adolescents below the legal drinking age of 18 years comprised of 61% of all brand appearances. Alcohol content, including branding, is highly prevalent in the UK Reality TV show 'Geordie Shore' Series 11. Two-thirds of all alcohol branding occurred in episodes age-rated by the British Board of Film Classification (BBFC) as suitable for viewers aged 15 years. The organizations OfCom, Advertising Standards Authority (ASA) and the Portman Group should implement more effective policies to reduce adolescent exposure to on-screen drinking. The drinks industry should consider demanding the withdrawal of their brands from the show. Alcohol content, including branding, is highly prevalent in the MTV reality TV show 'Geordie Shore' Series 11. Current alcohol regulation is failing to protect young viewers from exposure to such content.

Multigrid Techniques for Highly Indefinite Equations

NASA Technical Reports Server (NTRS)

Shapira, Yair

1996-01-01

A multigrid method for the solution of finite difference approximations of elliptic PDE's is introduced. A parallelizable version of it, suitable for two and multi level analysis, is also defined, and serves as a theoretical tool for deriving a suitable implementation for the main version. For indefinite Helmholtz equations, this analysis provides a suitable mesh size for the coarsest grid used. Numerical experiments show that the method is applicable to diffusion equations with discontinuous coefficients and highly indefinite Helmholtz equations.

Raster-based outranking method: a new approach for municipal solid waste landfill (MSW) siting.

PubMed

Hamzeh, Mohamad; Abbaspour, Rahim Ali; Davalou, Romina

2015-08-01

MSW landfill siting is a complicated process because it requires integration of several factors. In this paper, geographic information system (GIS) and multiple criteria decision analysis (MCDA) were combined to handle the municipal solid waste (MSW) landfill siting. For this purpose, first, 16 input data layers were prepared in GIS environment. Then, the exclusionary lands were eliminated and potentially suitable areas for the MSW disposal were identified. These potentially suitable areas, in an innovative approach, were further examined by deploying Preference Ranking Organization Method for Enrichment Evaluations (PROMETHEE) II and analytic network process (ANP), which are two of the most recent MCDA methods, in order to determine land suitability for landfilling. PROMETHEE II was used to determine a complete ranking of the alternatives, while ANP was employed to quantify the subjective judgments of evaluators as criteria weights. The resulting land suitability was reported on a grading scale of 1-5 from 1 to 5, which is the least to the most suitable area, respectively. Finally, three optimal sites were selected by taking into consideration the local conditions of 15 sites, which were candidates for MSW landfilling. Research findings show that the raster-based method yields effective results.

Multiscale turbulence models based on convected fluid microstructure

NASA Astrophysics Data System (ADS)

Holm, Darryl D.; Tronci, Cesare

2012-11-01

The Euler-Poincaré approach to complex fluids is used to derive multiscale equations for computationally modeling Euler flows as a basis for modeling turbulence. The model is based on a kinematic sweeping ansatz (KSA) which assumes that the mean fluid flow serves as a Lagrangian frame of motion for the fluctuation dynamics. Thus, we regard the motion of a fluid parcel on the computationally resolvable length scales as a moving Lagrange coordinate for the fluctuating (zero-mean) motion of fluid parcels at the unresolved scales. Even in the simplest two-scale version on which we concentrate here, the contributions of the fluctuating motion under the KSA to the mean motion yields a system of equations that extends known results and appears to be suitable for modeling nonlinear backscatter (energy transfer from smaller to larger scales) in turbulence using multiscale methods.

Using supercomputers for the time history analysis of old gravity dams

NASA Astrophysics Data System (ADS)

Rouve, G.; Peters, A.

Some of the old masonry dams that were built in Germany at the beginning of this century are a matter of concern today. In the course of time certain deterioration caused or amplified by aging has appeared and raised questions about the safety of these old dams. The Finite Element Method, which in the past two decades has found a widespread application, offers a suitable tool to re-evaluate the safety of these old gravity dams. The reliability of the results, however, strongly depends on the knowledge of the material parameters. Using historical records and observations a numerical back-analysis models has been developed to simulate the behaviour of these old masonry structures and to estimate their material properties by calibration. Only an implementation on a fourth generation vector computer made the application of this large model possible in practice.

Resonant-Plasmon-Assisted Subwavelength Ablation by a Femtosecond Oscillator

DOE PAGES

Shi, Liping; Iwan, Bianca; Ripault, Quentin; ...

2018-02-02

Here, we experimentally demonstrate the use of subwavelength optical nanoantennas to assist a direct nanoscale ablation using the ultralow fluence of a Ti:sapphire oscillator through the excitation of surface plasmon waves. The mechanism is attributed to nonthermal transient unbonding and electrostatic ablation, which is triggered by the surface plasmon-enhanced field electron emission and acceleration in vacuum. We show that the electron-driven ablation appears for both nanoscale metallic as well as dielectric materials. While the observed surface plasmon-enhanced local ablation may limit the applications of nanostructured surfaces in extreme nonlinear nanophotonics, it, nevertheless, also provides a method for nanomachining, manipulation, andmore » modification of nanoscale materials. Lastly, collateral thermal damage to the antenna structure can be suitably avoided, and nonlinear conversion processes can be stabilized by a dielectric overcoating of the antenna.« less

Method of preparation of uranium nitride

DOEpatents

Kiplinger, Jaqueline Loetsch; Thomson, Robert Kenneth James

2013-07-09

Method for producing terminal uranium nitride complexes comprising providing a suitable starting material comprising uranium; oxidizing the starting material with a suitable oxidant to produce one or more uranium(IV)-azide complexes; and, sufficiently irradiating the uranium(IV)-azide complexes to produce the terminal uranium nitride complexes.

Buried Man-made Structure Imaging using 2-D Resistivity Inversion

NASA Astrophysics Data System (ADS)

Anderson Bery, Andy; Nordiana, M. M.; El Hidayah Ismail, Noer; Jinmin, M.; Nur Amalina, M. K. A.

2018-04-01

This study is carried out with the objective to determine the suitable resistivity inversion method for buried man-made structure (bunker). This study was carried out with two stages. The first stage is suitable array determination using 2-D computerized modeling method. One suitable array is used for the infield resistivity survey to determine the dimension and location of the target. The 2-D resistivity inversion results showed that robust inversion method is suitable to resolve the top and bottom part of the buried bunker as target. In addition, the dimension of the buried bunker is successfully determined with height of 7 m and length of 20 m. The location of this target is located at -10 m until 10 m of the infield resistivity survey line. The 2-D resistivity inversion results obtained in this study showed that the parameters selection is important in order to give the optimum results. These parameters are array type, survey geometry and inversion method used in data processing.

Equity and Lifelong Learning: Lessons from Workplace Learning in Scottish SMEs

ERIC Educational Resources Information Center

Riddell, Sheila; Ahlgren, Linda; Weedon, Elisabet

2009-01-01

Workplace learning is identified by UK and Scottish governments as an important means of achieving social mobility, and therefore producing a more equal society. However, there appears to be a patchwork of provision and funding arrangements, making it difficult for employers and employees to identify suitable routes. Analysis of large scale survey…

76 FR 27288 - Port Access Route Study: The Atlantic Coast From Maine to Florida

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-11

... rerouting traffic, funneling traffic, and placement of structures (e.g., wind turbines) that may obstruct... November 2010, the Secretary of the Department of the Interior (DOI) announced Wind Energy Areas (WEAs) off.... These WEAs are offshore locations that appear most suitable for wind energy development. All of the...

cl_reg9_swcoast_50mwind

Science.gov Websites

is not suitable for micro-siting potential development projects. This shapefile was generated from a , LLC for the U.S. Department of Energy ("DOE"). The user is granted the right, without any , provided that this entire notice appears in all copies of the data. Further, the user of this data agrees

Object knowledge modulates colour appearance.

PubMed

Witzel, Christoph; Valkova, Hanna; Hansen, Thorsten; Gegenfurtner, Karl R

2011-01-01

We investigated the memory colour effect for colour diagnostic artificial objects. Since knowledge about these objects and their colours has been learned in everyday life, these stimuli allow the investigation of the influence of acquired object knowledge on colour appearance. These investigations are relevant for questions about how object and colour information in high-level vision interact as well as for research about the influence of learning and experience on perception in general. In order to identify suitable artificial objects, we developed a reaction time paradigm that measures (subjective) colour diagnosticity. In the main experiment, participants adjusted sixteen such objects to their typical colour as well as to grey. If the achromatic object appears in its typical colour, then participants should adjust it to the opponent colour in order to subjectively perceive it as grey. We found that knowledge about the typical colour influences the colour appearance of artificial objects. This effect was particularly strong along the daylight axis.

Object knowledge modulates colour appearance

PubMed Central

Witzel, Christoph; Valkova, Hanna; Hansen, Thorsten; Gegenfurtner, Karl R

2011-01-01

We investigated the memory colour effect for colour diagnostic artificial objects. Since knowledge about these objects and their colours has been learned in everyday life, these stimuli allow the investigation of the influence of acquired object knowledge on colour appearance. These investigations are relevant for questions about how object and colour information in high-level vision interact as well as for research about the influence of learning and experience on perception in general. In order to identify suitable artificial objects, we developed a reaction time paradigm that measures (subjective) colour diagnosticity. In the main experiment, participants adjusted sixteen such objects to their typical colour as well as to grey. If the achromatic object appears in its typical colour, then participants should adjust it to the opponent colour in order to subjectively perceive it as grey. We found that knowledge about the typical colour influences the colour appearance of artificial objects. This effect was particularly strong along the daylight axis. PMID:23145224

Statistical Approaches Used to Assess the Equity of Access to Food Outlets: A Systematic Review

PubMed Central

Lamb, Karen E.; Thornton, Lukar E.; Cerin, Ester; Ball, Kylie

2015-01-01

Background Inequalities in eating behaviours are often linked to the types of food retailers accessible in neighbourhood environments. Numerous studies have aimed to identify if access to healthy and unhealthy food retailers is socioeconomically patterned across neighbourhoods, and thus a potential risk factor for dietary inequalities. Existing reviews have examined differences between methodologies, particularly focussing on neighbourhood and food outlet access measure definitions. However, no review has informatively discussed the suitability of the statistical methodologies employed; a key issue determining the validity of study findings. Our aim was to examine the suitability of statistical approaches adopted in these analyses. Methods Searches were conducted for articles published from 2000–2014. Eligible studies included objective measures of the neighbourhood food environment and neighbourhood-level socio-economic status, with a statistical analysis of the association between food outlet access and socio-economic status. Results Fifty-four papers were included. Outlet accessibility was typically defined as the distance to the nearest outlet from the neighbourhood centroid, or as the number of food outlets within a neighbourhood (or buffer). To assess if these measures were linked to neighbourhood disadvantage, common statistical methods included ANOVA, correlation, and Poisson or negative binomial regression. Although all studies involved spatial data, few considered spatial analysis techniques or spatial autocorrelation. Conclusions With advances in GIS software, sophisticated measures of neighbourhood outlet accessibility can be considered. However, approaches to statistical analysis often appear less sophisticated. Care should be taken to consider assumptions underlying the analysis and the possibility of spatially correlated residuals which could affect the results. PMID:29546115

Analysis of intraosseous samples using point of care technology--an experimental study in the anaesthetised pig.

PubMed

Strandberg, Gunnar; Eriksson, Mats; Gustafsson, Mats G; Lipcsey, Miklós; Larsson, Anders

2012-11-01

Intraosseous access is an essential method in emergency medicine when other forms of vascular access are unavailable and there is an urgent need for fluid or drug therapy. A number of publications have discussed the suitability of using intraosseous access for laboratory testing. We aimed to further evaluate this issue and to study the accuracy and precision of intraosseous measurements. Five healthy, anaesthetised pigs were instrumented with bilateral tibial intraosseous cannulae and an arterial catheter. Samples were collected hourly for 6h and analysed for blood gases, acid base status, haemoglobin and electrolytes using an I-Stat point of care analyser. There was no clinically relevant difference between results from left and right intraosseous sites. The variability of the intraosseous sample values, measured as the coefficient of variance (CV), was maximally 11%, and smaller than for the arterial sample values for all variables except SO2. For most variables, there seems to be some degree of systematic difference between intraosseous and arterial results. However, the direction of this difference seems to be predictable. Based on our findings in this animal model, cartridge based point of care instruments appear suitable for the analysis of intraosseous samples. The agreement between intraosseous and arterial analysis seems to be good enough for the method to be clinically useful. The precision, quantified in terms of CV, is at least as good for intraosseous as for arterial analysis. There is no clinically important difference between samples from left and right tibia, indicating a good reproducibility. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Performance and Storage Integrity of Dried Blood Spots for PCB, BFR and Pesticide Measurements

PubMed Central

Batterman, Stuart; Chernyak, Sergei

2014-01-01

Dried blood spots (DBS) can provide accurate and valuable estimates of exposure to environmental toxicants, and the use of information derived from archived newborn DBS information has enormous potential to open up new research on the impacts of early chemical exposure on disease. Broad application of DBS for the purpose of quantitative exposure estimation requires robust and validated methods. This study investigates the suitability of DBS analyses for population studies of exposure to three chemical groups: polychlorinated biphenyls (PCBs), brominated flame retardants (BFRs), and chlorinated pesticides. It examines background (matrix) contamination, recovery and extraction variability, sensitivity, and storage stability. DBS samples prepared using 50 μL of adult blood were analyzed by GC/MS, and method performance was confirmed by using certified materials and paired DBS-blood samples from six volunteers. Several of the target compounds and their degradation products have not been previously measured in DBS. All target compounds were detected in DBS samples collected from the volunteers. Sample DBS cards showed background contamination of several compounds. When stored at room temperature, target compounds, excluding PBDEs, were stable for up to one month. When refrigerated or frozen, stability was acceptable for all compounds up to one year, and multiyear storage appears acceptable at colder (e.g., −80 °C) temperatures. Multicompartment models may be used to estimate or correct for storage losses. Considering concentrations of contaminants for adults and children reported in the literature, and experimental values of detection limits and background contamination, DBS samples are suitable for quantifying exposures to many PCBs, BFRs and persistent pesticides. PMID:25058892

Building a high resolution national elevation model from SRTM: The Australian experience

NASA Astrophysics Data System (ADS)

Gallant, J. C.; Read, A.; Dowling, T. I.

2011-12-01

The global SRTM DEM is a valuable global data set that, for many countries including Australia, provides the best basis for a fine resolution national DEM. But the SRTM data suffers from a variety of artefacts and errors that prevent its routine application with familiar terrain analysis tools. The most important of these are stripes, voids, random noise and offsets due to trees. The tree offsets are particularly disruptive in riparian areas where they make rivers appear as ridge lines. This paper describes how a suite of tools was applied to the 1 second SRTM data for Australia to treat each of these artefacts. An FFT-based tool was developed to detect and remove regular striping. Voids were filled using a modification of the delta surface fill method. Offsets due to trees were modelled and removed using a vegetation mask derived from remotely sensed imagery and a statistical estimate of the offset at vegetation patch boundaries. Random noise was removed using an adaptive smoothing method that responds to variations in both local relief and noise magnitude. Finally, mapped channel networks were imposed using a modified version of the ANUDEM software to enforce hydrological connectivity. The resulting products are being distributed by Geoscience Australia and the smoothed and drainage enforced products in particular are suitable for use in routine terrain analysis tasks. With some adaptation, the same processes could be applied to the global SRTM to derive a product that, in combination with an improved ASTER G-DEM, would provide a high quality comprehensive global elevation model suitable for most purposes.

Gas chromatography-mass spectrometry of hexafluoroacetone derivatives: First time utilization of a gaseous phase derivatizing agent for analysis of extraterrestrial amino acids.

PubMed

Geffroy-Rodier, C; Buch, A; Sternberg, R; Papot, S

2012-07-06

Within the perspective of the current and next space missions to Mars (MSL 2011 and Exomars 2016-2018), the detection and enantioselective separation of building blocks such as the amino acids are important subjects which are becoming fundamental for the search for traces of life on the surface and subsurface of Mars. In this work, we have developed and optimized a method adapted to space experimentation to derivatize and analyze amino acids, using hexafluoroacetone as the derivatizing agent. The temperature, duration of the derivative transfer to the analyser, and chromatographic separation parameters have been optimized to meet the instrument design constraints imposed on devices for extraterrestrial experiments. The work presented in this rationale has established that hexafluoroacetone, in addition to its intrinsic qualities, such as the production of light-weight derivatives (no racemization) and great resistance to the drastic operating conditions, has indeed facilitated simple and fast derivatization that appears to be suitable for in situ analysis in space. By using hexafluoroacetone as the derivatizing agent, we successfully identified, 21 amino acids including 12 of the 20 proteinic amino acids without stirring or extraction steps. Ten of these derivatized amino acids were enantioselectively separated. The precision and accuracy measurements for the D/L ratio showed that the proposed method was also suitable for the determination of both enantioselective forms of most of the tested amino acids. The limits of detection obtained were lower than the ppb level of organic molecules detected in Martian meteorites. Copyright © 2012 Elsevier B.V. All rights reserved.

USE OF MODELS FOR GAMMA SHIELDING STUDIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clifford, C.E.

1962-02-01

The use of models for shielding studies of buildings exposed to gamma radiation was evaluated by comparing the dose distributions produced in a blockhouse with movable inside walls exposed to 0.66 Mev gamma radiation with corresponding distributions in an iron 1 to 10 scale model. The effects of air and ground scaling on the readings in the model were also investigated. Iron appeared to be a suitable model material for simple closed buildings but for more complex structures it appeared that the use of iron models would progressively overestimite the gamms shielding protection as the complexity increased. (auth)

Comparing Facial 3D Analysis With DNA Testing to Determine Zygosities of Twins.

PubMed

Vuollo, Ville; Sidlauskas, Mantas; Sidlauskas, Antanas; Harila, Virpi; Salomskiene, Loreta; Zhurov, Alexei; Holmström, Lasse; Pirttiniemi, Pertti; Heikkinen, Tuomo

2015-06-01

The aim of this study was to compare facial 3D analysis to DNA testing in twin zygosity determinations. Facial 3D images of 106 pairs of young adult Lithuanian twins were taken with a stereophotogrammetric device (3dMD, Atlanta, Georgia) and zygosity was determined according to similarity of facial form. Statistical pattern recognition methodology was used for classification. The results showed that in 75% to 90% of the cases, zygosity determinations were similar to DNA-based results. There were 81 different classification scenarios, including 3 groups, 3 features, 3 different scaling methods, and 3 threshold levels. It appeared that coincidence with 0.5 mm tolerance is the most suitable feature for classification. Also, leaving out scaling improves results in most cases. Scaling was expected to equalize the magnitude of differences and therefore lead to better recognition performance. Still, better classification features and a more effective scaling method or classification in different facial areas could further improve the results. In most of the cases, male pair zygosity recognition was at a higher level compared with females. Erroneously classified twin pairs appear to be obvious outliers in the sample. In particular, faces of young dizygotic (DZ) twins may be so similar that it is very hard to define a feature that would help classify the pair as DZ. Correspondingly, monozygotic (MZ) twins may have faces with quite different shapes. Such anomalous twin pairs are interesting exceptions, but they form a considerable portion in both zygosity groups.

Selection of a suitable method for the preparation of polymeric nanoparticles: multi-criteria decision making approach.

PubMed

Krishnamoorthy, Kannan; Mahalingam, Manikandan

2015-03-01

The present study is aimed to select the suitable method for preparation of camptothecin loaded polymeric nanoparticles by utilizing the multi-criteria decision making method. Novel approaches of drug delivery by formulation using nanotechnology are revolutionizing the future of medicine. Recent years have witnessed unprecedented growth of research and application in the area of nanotechnology. Nanoparticles have become an important area of research in the field of drug delivery because they have the ability to deliver a wide range of drug to varying areas of body. Despite of extensive research and development, polymeric nanoparticles are frequently used to improve the therapeutic effect of drugs. A number of techniques are available for the preparation of polymeric nanoparticles. The Analytical Hierarchy Process (AHP) is a method for decision making, which are derived from individual judgements for qualitative factors, using the pair-wise comparison matrix. In AHP, a decision hierarchy is constructed with a goal, criteria and alternatives. The model uses three main criteria 1) Instrument, 2) Process and Output and 3) Cost. In addition, there are eight sub-criteria's as well as eight alternatives. Pair-wise comparison matrixes are used to obtain the overall priority weight and ranking for the selection of suitable method. Nanoprecipitation technique is the most suitable method for the preparation of camptothecin loaded polymeric nanoparticles with the highest overall priority weight of 0.297 CONCLUSION: In particular, the result indicates that the priority weights obtained from AHP could be defined as a multiple output for finding out the most suitable method for preparation of camptothecin loaded polymeric nanoparticles.

Evaluation of preparation methods for suspended nano-objects on substrates for dimensional measurements by atomic force microscopy

PubMed Central

Göhler, Daniel; Wessely, Benno; Stintz, Michael; Lazzerini, Giovanni Mattia; Yacoot, Andrew

2017-01-01

Dimensional measurements on nano-objects by atomic force microscopy (AFM) require samples of safely fixed and well individualized particles with a suitable surface-specific particle number on flat and clean substrates. Several known and proven particle preparation methods, i.e., membrane filtration, drying, rinsing, dip coating as well as electrostatic and thermal precipitation, were performed by means of scanning electron microscopy to examine their suitability for preparing samples for dimensional AFM measurements. Different suspensions of nano-objects (with varying material, size and shape) stabilized in aqueous solutions were prepared therefore on different flat substrates. The drop-drying method was found to be the most suitable one for the analysed suspensions, because it does not require expensive dedicated equipment and led to a uniform local distribution of individualized nano-objects. Traceable AFM measurements based on Si and SiO2 coated substrates confirmed the suitability of this technique. PMID:28904839

Evaluation of preparation methods for suspended nano-objects on substrates for dimensional measurements by atomic force microscopy.

PubMed

Fiala, Petra; Göhler, Daniel; Wessely, Benno; Stintz, Michael; Lazzerini, Giovanni Mattia; Yacoot, Andrew

2017-01-01

Dimensional measurements on nano-objects by atomic force microscopy (AFM) require samples of safely fixed and well individualized particles with a suitable surface-specific particle number on flat and clean substrates. Several known and proven particle preparation methods, i.e., membrane filtration, drying, rinsing, dip coating as well as electrostatic and thermal precipitation, were performed by means of scanning electron microscopy to examine their suitability for preparing samples for dimensional AFM measurements. Different suspensions of nano-objects (with varying material, size and shape) stabilized in aqueous solutions were prepared therefore on different flat substrates. The drop-drying method was found to be the most suitable one for the analysed suspensions, because it does not require expensive dedicated equipment and led to a uniform local distribution of individualized nano-objects. Traceable AFM measurements based on Si and SiO 2 coated substrates confirmed the suitability of this technique.

Selection of a Suitable Method for the Preparation of Polymeric Nanoparticles: Multi-Criteria Decision Making Approach

PubMed Central

Krishnamoorthy, Kannan; Mahalingam, Manikandan

2015-01-01

Purpose: The present study is aimed to select the suitable method for preparation of camptothecin loaded polymeric nanoparticles by utilizing the multi-criteria decision making method. Novel approaches of drug delivery by formulation using nanotechnology are revolutionizing the future of medicine. Recent years have witnessed unprecedented growth of research and application in the area of nanotechnology. Nanoparticles have become an important area of research in the field of drug delivery because they have the ability to deliver a wide range of drug to varying areas of body. Methods: Despite of extensive research and development, polymeric nanoparticles are frequently used to improve the therapeutic effect of drugs. A number of techniques are available for the preparation of polymeric nanoparticles. The Analytical Hierarchy Process (AHP) is a method for decision making, which are derived from individual judgements for qualitative factors, using the pair-wise comparison matrix. In AHP, a decision hierarchy is constructed with a goal, criteria and alternatives. Results: The model uses three main criteria 1) Instrument, 2) Process and Output and 3) Cost. In addition, there are eight sub-criteria’s as well as eight alternatives. Pair-wise comparison matrixes are used to obtain the overall priority weight and ranking for the selection of suitable method. Nanoprecipitation technique is the most suitable method for the preparation of camptothecin loaded polymeric nanoparticles with the highest overall priority weight of 0.297 Conclusion: In particular, the result indicates that the priority weights obtained from AHP could be defined as a multiple output for finding out the most suitable method for preparation of camptothecin loaded polymeric nanoparticles. PMID:25789220

Methods of Constructing a Blended Performance Function Suitable for Formation Flight

NASA Technical Reports Server (NTRS)

Ryan, Jack

2017-01-01

Two methods for constructing performance functions for formation fight-for-drag-reduction suitable for use with an extreme-seeking control system are presented. The first method approximates an a prior measured or estimated drag-reduction performance function by combining real-time measurements of readily available parameters. The parameters are combined with weightings determined from a minimum squares optimization to form a blended performance function.

Rational design of crystal contact-free space in protein crystals for analyzing spatial distribution of motions within protein molecules.

PubMed

Matsuoka, Rei; Shimada, Atsushi; Komuro, Yasuaki; Sugita, Yuji; Kohda, Daisuke

2016-03-01

Contacts with neighboring molecules in protein crystals inevitably restrict the internal motions of intrinsically flexible proteins. The resultant clear electron densities permit model building, as crystallographic snapshot structures. Although these still images are informative, they could provide biased pictures of the protein motions. If the mobile parts are located at a site lacking direct contacts in rationally designed crystals, then the amplitude of the movements can be experimentally analyzed. We propose a fusion protein method, to create crystal contact-free space (CCFS) in protein crystals and to place the mobile parts in the CCFS. Conventional model building fails when large amplitude motions exist. In this study, the mobile parts appear as smeared electron densities in the CCFS, by suitable processing of the X-ray diffraction data. We applied the CCFS method to a highly mobile presequence peptide bound to the mitochondrial import receptor, Tom20, and a catalytically relevant flexible segment in the oligosaccharyltransferase, AglB. These two examples demonstrated the general applicability of the CCFS method to the analysis of the spatial distribution of motions within protein molecules. © 2016 The Protein Society.

Novel Injectable Calcium Phosphate Bone Cement from Wet Chemical Precipitation Method

NASA Astrophysics Data System (ADS)

Hablee, S.; Sopyan, I.; Mel, M.; Salleh, H. M.; Rahman, M. M.; Singh, R.

2017-06-01

Calcium phosphate cement has been prepared via chemical precipitation method for injectable bone filling materials. Calcium hydroxide, Ca(OH)2, and diammonium hydrogen phosphate, (NH4)2HPO4, were used as calcium and phosphorus precursors respectively. The synthesized powder was mixed with water at different powder-to-liquid (P/L) ratios, which was adjusted at 0.8, 0.9, 1.0, 1.1 and 1.2. The influence of P/L ratio on the injectability, setting time and mechanical strength of calcium phosphate cement paste has been evaluated. The synthesized powder appeared as purely hydroxyapatite with nanosized and agglomerated spherical particles. All cement pastes show excellent injectability except for the paste with P/L ratio 1.2. Calcium phosphate cement with P/L ratio 1.1 shows the ideal cement for bone filler application with good injectability, the initial and final setting times of 30 min and 160 min, and the compression strength of 2.47 MPa. The result indicated that the newly developed calcium phosphate cement is physically suitable for bone filler application. This paper presents our investigation on the effect of P/L ratio on the handling and mechanical properties of calcium phosphate cement prepared via wet chemical precipitation method.

Development of porous structured polyvinyl alcohol/zeolite/carbon composites as adsorbent

NASA Astrophysics Data System (ADS)

Laksmono, J. A.; Sudibandriyo, M.; Saputra, A. H.; Haryono, A.

2017-05-01

Adsorption is a separation process that has higher energy efficiency than others. Analyzing the nature of the adsorbate and the selection of suitable adsorbent are key success in adsorption. The performance of the adsorbent can be modified either physically or chemically to obtain the efficiency and effectiveness of the adsorption, this can be facilitated by using a composite adsorbent. In this study, we have conducted the preparation process of a polyvinyl alcohol (PVA)/zeolite/carbon composites. The resulting adsorbent composites are dedicated for ethanol - water dehydration proposes. The composites were prepared using cross-linked polymerization method followed by supercritical fluid extraction (SFE) to obtain the porous structured upon drying process. The characterization of the functional groups and morphology were performed by using Fourier Transform Infra-Red (FTIR) and Scanning Electron Microscopy (SEM), respectively. The FTIR analysis showed that composite prepared by SFE method formed hydrogen bonding confirmed by the appearance of peaks at 2950 - 3000 cm-1 compared to composite without SFE method, whereas, the results of SEM study showed the formation of three layered structures. On basis of the obtained results, it can be shown that PVA/zeolite/carbon has high potential to be develop further as an adsorbent composite.

A novel false color mapping model-based fusion method of visual and infrared images

NASA Astrophysics Data System (ADS)

Qi, Bin; Kun, Gao; Tian, Yue-xin; Zhu, Zhen-yu

2013-12-01

A fast and efficient image fusion method is presented to generate near-natural colors from panchromatic visual and thermal imaging sensors. Firstly, a set of daytime color reference images are analyzed and the false color mapping principle is proposed according to human's visual and emotional habits. That is, object colors should remain invariant after color mapping operations, differences between infrared and visual images should be enhanced and the background color should be consistent with the main scene content. Then a novel nonlinear color mapping model is given by introducing the geometric average value of the input visual and infrared image gray and the weighted average algorithm. To determine the control parameters in the mapping model, the boundary conditions are listed according to the mapping principle above. Fusion experiments show that the new fusion method can achieve the near-natural appearance of the fused image, and has the features of enhancing color contrasts and highlighting the infrared brilliant objects when comparing with the traditional TNO algorithm. Moreover, it owns the low complexity and is easy to realize real-time processing. So it is quite suitable for the nighttime imaging apparatus.

A homogeneous biochemiluminescent assay for detection of influenza

NASA Astrophysics Data System (ADS)

Hui, Kwok Min; Li, Xiao Jing; Pan, Lu; Li, X. J.

2015-05-01

Current methods of rapid detection of influenza are based on detection of the nucleic acids or antigens of influenza viruses. Since influenza viruses constantly mutate leading to appearance of new strains or variants of viruses, these detection methods are susceptible to genetic changes in influenza viruses. Type A and B influenza viruses contain neuraminidase, an essential enzyme for virus replication which enables progeny influenza viruses leave the host cells to infect new cells. Here we describe an assay method, the homogeneous biochemiluminescent assay (HBA), for rapid detection of influenza by detecting viral neuraminidase activity. The assay mimics the light production process of a firefly: a viral neuraminidase specific substrate containing a luciferin moiety is cleaved in the presence of influenza virus to release luciferin, which becomes a substrate to firefly luciferase in a light production system. All reagents can be formulated in a single reaction mix so that the assay involves only one manual step, i.e., sample addition. Presence of Type A or B influenza virus in the sample leads to production of strong, stable and easily detectable light signal, which lasts for hours. Thus, this influenza virus assay is suitable for use in point-of-care settings.

[Use of an iliac branched endoprostheis in endovascular treatment for an abdominal aortic aneurysm combined with aneurysms of both common iliac arteries].

PubMed

Imaev, T E; Kuchin, I V; Lepilin, P M; Kolegaev, A S; Medvedeva, I S; Komlev, A E; Akchurin, R S

An abdominal aortic aneurysm appears to be combined with aneurysmatic lesions of the common iliac arteries in 30-40% of cases. Like abdominal aortic aneurysms, aneurysms of the common iliac arteries rarely manifest themselves clinically. The lethality rate in case of rupture is comparable to that for rupture of an abdominal aortic aneurysm. During endoprosthetic repair of abdominal aortic aneurysms combined with aneurysms of the common iliac arteries, in order to prevent endoleaks and to improve the distal zone of fixation of endografts surgeons often resort to embolization of internal iliac arteries, which may lead to ischaemic postoperative complications. One of the methods of preserving pelvic blood flow is the use of an iliac branched endograft. A series of studies evaluating long-term outcomes demonstrated that this method proved to be both safe and effective, and with the suitable anatomy is a method of choice in high surgical risk patients. The present article deals with a clinical case report concerning bilateral endoprosthetic repair of the common iliac arteries, combined with endoprosthetic repair of an abdominal aortic aneurysm, with the description of technical peculiarities of implanting an iliac branched graft.

Rapid and high resolution genotyping of all Escherichia coli serotypes using 10 genomic repeat-containing loci.

PubMed

Løbersli, Inger; Haugum, Kjersti; Lindstedt, Bjørn-Arne

2012-01-01

Our laboratory has previously published two multiple-locus variable-number tandem-repeats analysis (MLVA) methods for rapid genotyping of Escherichia coli (E. coli), which are now in routine use for surveillance and outbreak detection. The first assay developed was specific for E. coli O157:H7; however this assay was not suitable for genotyping other E. coli serotypes. A new generic MLVA-assay was then developed with the capability of genotyping all E. coli serotypes. This generic E. coli MLVA (GECM7) was based on polymorphism in seven variable number of tandem repeats (VNTR) loci. GECM7 worked well with the majority of E. coli serotypes; however we wanted to increase the resolution for this method based in part of comparison with PFGE typing of E. coli O26:H11, where PFGE appeared to display higher resolution. The GECM7 method was improved by adding three new repeat-loci to a total of ten (GECM10), and a considerable increase in resolution was observed (from 296 to 507 genotypes on the same set of strains). Copyright © 2011 Elsevier B.V. All rights reserved.

Evaluation of georeferencing methods with respect to their suitability to address unsimilarity between the image to be referenced and the reference image

NASA Astrophysics Data System (ADS)

Brüstle, Stefan; Erdnüß, Bastian

2016-10-01

In recent years, operational costs of unmanned aircraft systems (UAS) have been massively decreasing. New sensors satisfying weight and size restrictions of even small UAS cover many different spectral ranges and spatial resolutions. This results in airborne imagery having become more and more available. Such imagery is used to address many different tasks in various fields of application. For many of those tasks, not only the content of the imagery itself is of interest, but also its spatial location. This requires the imagery to be properly georeferenced. Many UAS have an integrated GPS receiver together with some kind of INS device acquiring the sensor orientation to provide the georeference. However, both GPS and INS data can easily become unavailable for a period of time during a flight, e.g. due to sensor malfunction, transmission problems or jamming. Imagery gathered during such times lacks georeference. Moreover, even in datasets not affected by such problems, GPS and INS inaccuracies together with a potentially poor knowledge of ground elevation can render location information accuracy less than sufficient for a given task. To provide or improve the georeference of an image affected by this, an image to reference registration can be performed if a suitable reference is available, e.g. a georeferenced orthophoto covering the area of the image to be georeferenced. Registration and thus georeferencing is achieved by determining a transformation between the image to be referenced and the reference which maximizes the coincidence of relevant structures present both in the former and the latter. Many methods have been developed to accomplish this task. Regardless of their differences they usually tend to perform the better the more similar an image and a reference are in appearance. This contribution evaluates a selection of such methods all differing in the type of structure they use for the assessment of coincidence with respect to their ability to tolerate unsimilarity in appearance. Similarity in appearance is mainly dependent on the following aspects, namely the similarity of abstraction levels (Is the reference e.g. an orthophoto or a topographical map?), the similarity of sensor types and spectral bands (Is the image e.g. a SAR image and the reference a passively sensed one? Was e.g. a NIR sensor used capturing the image while a VIS sensor was used in the reference?), the similarity of resolutions (Is the ground sampling distance of the reference comparable to the one of the image?), the similarity of capture parameters (Are e.g. the viewing angles comparable in the image and in the reference?) and the similarity concerning the image content (Was there e.g. snow coverage present when the image was captured while this was not the case when the reference was captured?). The evaluation is done by determining the performance of each method with a set of image to be referenced and reference pairs representing various degrees of unsimilarity with respect to each of the above mentioned aspects of similarity.

Evaluating a vessel for suitability for containing fluid

DOEpatents

Barefield, II, James E.; Judge, Elizabeth J.; Le, Loan A.; Lopez, Leon N.; Beveridge, Andrew C.; Chapman, Daniel R.; Taylor, Seth T.

2017-05-30

A method for evaluating a vessel for suitability to contain a fluid includes providing a vessel and forming a polished surface portion of the vessel by removing oxidation and/or contaminants from a portion of the vessel. The method further includes applying a focused laser to the polished surface portion to form plasma on the polished surface portion, and determining whether the vessel is suitable for containing a fluid based on silicon content of the polished surface portion. The silicon content is estimated based on light emitted from the plasma.

Generic method for the absolute quantification of glutathione S-conjugates: Application to the conjugates of acetaminophen, clozapine and diclofenac.

PubMed

den Braver, Michiel W; Vermeulen, Nico P E; Commandeur, Jan N M

2017-03-01

Modification of cellular macromolecules by reactive drug metabolites is considered to play an important role in the initiation of tissue injury by many drugs. Detection and identification of reactive intermediates is often performed by analyzing the conjugates formed after trapping by glutathione (GSH). Although sensitivity of modern mass spectrometrical methods is extremely high, absolute quantification of GSH-conjugates is critically dependent on the availability of authentic references. Although 1 H NMR is currently the method of choice for quantification of metabolites formed biosynthetically, its intrinsically low sensitivity can be a limiting factor in quantification of GSH-conjugates which generally are formed at low levels. In the present study, a simple but sensitive and generic method for absolute quantification of GSH-conjugates is presented. The method is based on quantitative alkaline hydrolysis of GSH-conjugates and subsequent quantification of glutamic acid and glycine by HPLC after precolumn derivatization with o-phthaldialdehyde/N-acetylcysteine (OPA/NAC). Because of the lower stability of the glycine OPA/NAC-derivate, quantification of the glutamic acid OPA/NAC-derivate appeared most suitable for quantification of GSH-conjugates. The novel method was used to quantify the concentrations of GSH-conjugates of diclofenac, clozapine and acetaminophen and quantification was consistent with 1 H NMR, but with a more than 100-fold lower detection limit for absolute quantification. Copyright © 2017. Published by Elsevier B.V.

Approaching Etuaptmumk--introducing a consensus-based mixed method for health services research.

PubMed

Chatwood, Susan; Paulette, Francois; Baker, Ross; Eriksen, Astrid; Hansen, Ketil Lenert; Eriksen, Heidi; Hiratsuka, Vanessa; Lavoie, Josée; Lou, Wendy; Mauro, Ian; Orbinski, James; Pabrum, Nathalie; Retallack, Hanna; Brown, Adalsteinn

2015-01-01

With the recognized need for health systems' improvements in the circumpolar and indigenous context, there has been a call to expand the research agenda across all sectors influencing wellness and to recognize academic and indigenous knowledge through the research process. Despite being recognized as a distinct body of knowledge in international forums and across indigenous groups, examples of methods and theories based on indigenous knowledge are not well documented in academic texts or peer-reviewed literature on health systems. This paper describes the use of a consensus-based, mixed method with indigenous knowledge by an experienced group of researchers and indigenous knowledge holders who collaborated on a study that explored indigenous values underlying health systems stewardship. The method is built on the principles of Etuaptmumk or two-eyed seeing, which aim to respond to and resolve the inherent conflicts between indigenous ways of knowing and the scientific inquiry that informs the evidence base in health care. Mixed methods' frameworks appear to provide a framing suitable for research questions that require data from indigenous knowledge sources and western knowledge. The nominal consensus method, as a western paradigm, was found to be responsive to embedding of indigenous knowledge and allowed space to express multiple perspectives and reach consensus on the question at hand. Further utilization and critical evaluation of this mixed methodology with indigenous knowledge are required.

Business And Industry Look Out For Their Own

ERIC Educational Resources Information Center

Kunze, Karl R.

1973-01-01

According to the author, counseling programs (i.e. ones which do more than give out information and help employees move from incompatible jobs within the company to more suitable ones) are relatively rare in business and industry. It appears that counseling in industry will be provided by its own people--the line supervisor and the personnel…

What Have We Learnt about Mobile LifeLong Learning (mLLL)?

ERIC Educational Resources Information Center

Seta, Luciano; Kukulska-Hulme, Agnes; Arrigo, Marco

2014-01-01

Mobile technologies are becoming ubiquitous in education, yet the wider implications of this phenomenon are not well understood. The paper discusses how mobile lifelong learning (mLLL) may be defined, and the challenges of forging a suitable definition in an ever-shifting technological and socio-economic landscape. mLLL appears as a ubiquitous…

minimUML: A Minimalist Approach to UML Diagramming for Early Computer Science Education

ERIC Educational Resources Information Center

Turner, Scott A.; Perez-Quinones, Manuel A.; Edwards, Stephen H.

2005-01-01

In introductory computer science courses, the Unified Modeling Language (UML) is commonly used to teach basic object-oriented design. However, there appears to be a lack of suitable software to support this task. Many of the available programs that support UML focus on developing code and not on enhancing learning. Programs designed for…

Density correlators in a self-similar cascade

NASA Astrophysics Data System (ADS)

Bialas, A.; Czyz˙; Ewski, J.

1999-09-01

Multivariate density moments (correlators) of arbitrary order are obtained for the multiplicative self-similar cascade. This result is based on the calculation by Greiner, Eggers and Lipa where the correlators of the logarithms of the particle densities have been obtained. The density correlators, more suitable for comparison with multiparticle data, appear to have a simple factorizable form.

On-Bark Behavior of Dendroctonus frontalis: A Markov Chain Analysis

Treesearch

J. Bishir; James H. Roberds; Brian L. Strom

2004-01-01

Tree-killing species of the Scolytidae (Coleoptera) must locate suitable hosts at least once per generation for successful reproduction. The process used to select hosts is complex, involving a sequence of steps and many possible outcomes. Because more beetles land on bark (host-find) than bore galleries (host-recognize), postlanding behaviors appear to be important in...

Reaction monitoring using hyperpolarized NMR with scaling of heteronuclear couplings by optimal tracking

NASA Astrophysics Data System (ADS)

Zhang, Guannan; Schilling, Franz; Glaser, Steffen J.; Hilty, Christian

2016-11-01

Off-resonance decoupling using the method of Scaling of Heteronuclear Couplings by Optimal Tracking (SHOT) enables determination of heteronuclear correlations of chemical shifts in single scan NMR spectra. Through modulation of J-coupling evolution by shaped radio frequency pulses, off resonance decoupling using SHOT pulses causes a user-defined dependence of the observed J-splitting, such as the splitting of 13C peaks, on the chemical shift offset of coupled nuclei, such as 1H. Because a decoupling experiment requires only a single scan, this method is suitable for characterizing on-going chemical reactions using hyperpolarization by dissolution dynamic nuclear polarization (D-DNP). We demonstrate the calculation of [13C, 1H] chemical shift correlations of the carbanionic active sites from hyperpolarized styrene polymerized using sodium naphthalene as an initiator. While off resonance decoupling by SHOT pulses does not enhance the resolution in the same way as a 2D NMR spectrum would, the ability to obtain the correlations in single scans makes this method ideal for determination of chemical shifts in on-going reactions on the second time scale. In addition, we present a novel SHOT pulse that allows to scale J-splittings 50% larger than the respective J-coupling constant. This feature can be used to enhance the resolution of the indirectly detected chemical shift and reduce peak overlap, as demonstrated in a model reaction between p-anisaldehyde and isobutylamine. For both pulses, the accuracy is evaluated under changing signal-to-noise ratios (SNR) of the peaks from reactants and reaction products, with an overall standard deviation of chemical shift differences compared to reference spectra of 0.02 ppm when measured on a 400 MHz NMR spectrometer. Notably, the appearance of decoupling side-bands, which scale with peak intensity, appears to be of secondary importance.

[Analysis and research of brain-computer interface experiments for imaging left-right hands movement].

PubMed

Wu, Yazhou; He, Qinghua; Huang, Hua; Zhang, Ling; Zhuo, Yu; Xie, Qi; Wu, Baoming

2008-10-01

This is a research carried out to explore a pragmatic way of BCI based imaging movement, i. e. to extract the feature of EEG for reflecting different thinking by searching suitable methods of signal extraction and recognition algorithm processing, to boost the recognition rate of communication for BCI system, and finally to establish a substantial theory and experimental support for BCI application. In this paper, different mental tasks for imaging left-right hands movement from 6 subjects were studied in three different time sections (hint keying at 2s, 1s and 0s after appearance of arrow). Then we used wavelet analysis and Feed-forward Back-propagation Neural Network (BP-NN) method for processing and analyzing the experimental data of off-line. Delay time delta t2, delta t1 and delta t0 for all subjects in the three different time sections were analyzed. There was significant difference between delta to and delta t2 or delta t1 (P<0.05), but no significant difference was noted between delta t2 and delta t1 (P>0.05). The average results of recognition rate were 65%, 86.67% and 72%, respectively. There were obviously different features for imaging left-right hands movement about 0.5-1s before actual movement; these features displayed significant difference. We got higher recognition rate of communication under the hint keying at about 1s after the appearance of arrow. These showed the feasibility of using the feature signals extracted from the project as the external control signals for BCI system, and demon strated that the project provided new ideas and methods for feature extraction and classification of mental tasks for BCI.

Multi-detection of preservatives in cheeses by liquid chromatography-tandem mass spectrometry.

PubMed

Fuselli, Fabio; Guarino, Chiara; La Mantia, Alessandro; Longo, Lucia; Faberi, Angelo; Marianella, Rosa Maria

2012-10-01

The incorrect use of preservatives in cheeses may compromise food safety and damage consumers. According to the law, more than one preservative may be contemporarily used in cheeses. So a method for their contemporary detection may be useful for both manufacturers and control agencies quality control. In this research a liquid chromatography-tandem mass spectrometric with electrospray ionization method for the multi-determination of seven preservatives (benzoic acid, citric acid, hexamethylenetetramine, lysozyme, natamycin, nisin and sorbic acid) in cheese was developed. The preservatives were contemporarily extracted from cheese by a single procedure, and analyzed by RP-LC/ESI-MS/MS (Ion Trap) in positive ionization mode, with single reaction monitoring (SRM) acquisition. Three sample types (hard, pasta filata and fresh cheese) were used for method evaluation. Recoveries were mostly higher than 90%; MDLs ranged from 0.02 to 0.26 mgkg(-1), and MQLs were included between 0.07 and 0.88 mgkg(-1). Due to matrix effect, quantitation was performed by referring to a matrix matched calibration curve, for each cheese typology. This method was also applied to commercial cheese samples, with good results. It appears fast, reliable and suitable for both screening and confirmation of the presence and quantitation of the preservatives in a single, multi-detection analysis. Copyright © 2012 Elsevier B.V. All rights reserved.

A new convergence analysis and perturbation resilience of some accelerated proximal forward-backward algorithms with errors

NASA Astrophysics Data System (ADS)

Reem, Daniel; De Pierro, Alvaro

2017-04-01

Many problems in science and engineering involve, as part of their solution process, the consideration of a separable function which is the sum of two convex functions, one of them possibly non-smooth. Recently a few works have discussed inexact versions of several accelerated proximal methods aiming at solving this minimization problem. This paper shows that inexact versions of a method of Beck and Teboulle (fast iterative shrinkable tresholding algorithm) preserve, in a Hilbert space setting, the same (non-asymptotic) rate of convergence under some assumptions on the decay rate of the error terms The notion of inexactness discussed here seems to be rather simple, but, interestingly, when comparing to related works, closely related decay rates of the errors terms yield closely related convergence rates. The derivation sheds some light on the somewhat mysterious origin of some parameters which appear in various accelerated methods. A consequence of the analysis is that the accelerated method is perturbation resilient, making it suitable, in principle, for the superiorization methodology. By taking this into account, we re-examine the superiorization methodology and significantly extend its scope. This work was supported by FAPESP 2013/19504-9. The second author was supported also by CNPq grant 306030/2014-4.

Remote pedestrians detection at night time in FIR Image using contrast filtering and locally projected region based CNN

NASA Astrophysics Data System (ADS)

Kim, Taehwan; Kim, Sungho

2017-02-01

This paper presents a novel method to detect the remote pedestrians. After producing the human temperature based brightness enhancement image using the temperature data input, we generates the regions of interest (ROIs) by the multiscale contrast filtering based approach including the biased hysteresis threshold and clustering, remote pedestrian's height, pixel area and central position information. Afterwards, we conduct local vertical and horizontal projection based ROI refinement and weak aspect ratio based ROI limitation to solve the problem of region expansion in the contrast filtering stage. Finally, we detect the remote pedestrians by validating the final ROIs using transfer learning with convolutional neural network (CNN) feature, following non-maximal suppression (NMS) with strong aspect ratio limitation to improve the detection performance. In the experimental results, we confirmed that the proposed contrast filtering and locally projected region based CNN (CFLP-CNN) outperforms the baseline method by 8% in term of logaveraged miss rate. Also, the proposed method is more effective than the baseline approach and the proposed method provides the better regions that are suitably adjusted to the shape and appearance of remote pedestrians, which makes it detect the pedestrian that didn't find in the baseline approach and are able to help detect pedestrians by splitting the people group into a person.

Monitoring of multiple bacteriocins through a developed dual extraction protocol and comparison of HPLC-DAD with turbidometry as their quantification system.

PubMed

Katharopoulos, Efstathios; Touloupi, Katerina; Touraki, Maria

2016-08-01

The present study describes the development of a simple and efficient screening system that allows identification and quantification of nine bacteriocins produced by Lactococcus lactis. Cell-free L. lactis extracts presented a broad spectrum of antibacterial activity, including Gram-negative bacteria, Gram-positive bacteria, and fungi. The characterization of their sensitivity to pH, and heat, showed that the extracts retained their antibacterial activity at extreme pH values and in a wide temperature range. The loss of antibacterial activity following treatment of the extracts with lipase or protease suggests a lipoproteinaceous nature of the produced antimicrobials. The extracts were subjected to a purification protocol that employs a two phase extraction using ammonium sulfate precipitation and organic solvent precipitation, followed by ion exchange chromatography, solid phase extraction and HPLC. In the nine fractions that presented antimicrobial activity, bacteriocins were quantified by the turbidometric method using a standard curve of nisin and by the HPLC method with nisin as the external standard, with both methods producing comparable results. Turbidometry appears to be unique in the qualitative determination of bacteriocins but the only method suitable to both separate and quantify the bacteriocins providing increased sensitivity, accuracy, and precision is HPLC. Copyright © 2016 Elsevier B.V. All rights reserved.

A sensitive and rapid determination of ranitidine in human plasma by HPLC with fluorescence detection and its application for a pharmacokinetic study.

PubMed

Ulu, Sevgi Tatar; Tuncel, Muzaffer

2012-04-01

A novel precolumn derivatization reversed-phase high-performance liquid chromatography method with fluorescence detection is described for the determination of ranitidine in human plasma. The method was based on the reaction of ranitidine with 4-fluoro-7-nitrobenzo-2-oxa-1,3-diazole forming yellow colored fluorescent product. The separation was achieved on a C(18) column using methanol-water (60:40, v/v) mobile phase. Fluorescence detection was used at the excitation and emission of 458 and 521 nm, respectively. Lisinopril was utilized as an internal standard. The flow rate was 1.2 mL/min. Ranitidine and lisinopril appeared at 3.24 and 2.25 min, respectively. The method was validated for system suitability, precision, accuracy, linearity, limit of detection, limit of quantification, recovery and robustness. Intra- and inter-day precisions of the assays were in the range of 0.01-0.44%. The assay was linear over the concentration range of 50-2000 ng/mL. The mean recovery was determined to be 96.40 ± 0.02%. This method was successfully applied to a pharmacokinetic study after oral administration of a dose (150 mg) of ranitidine. © The Author [2012]. Published by Oxford University Press. All rights reserved.

Applications of Computer Simulation Methods in Plastic Forming Technologies for Magnesium Alloys

NASA Astrophysics Data System (ADS)

Zhang, S. H.; Zheng, W. T.; Shang, Y. L.; Wu, X.; Palumbo, G.; Tricarico, L.

2007-05-01

Applications of computer simulation methods in plastic forming of magnesium alloy parts are discussed. As magnesium alloys possess very poor plastic formability at room temperature, various methods have been tried to improve the formability, for example, suitable rolling process and annealing procedures should be found to produce qualified magnesium alloy sheets, which have the reduced anisotropy and improved formability. The blank can be heated to a warm temperature or a hot temperature; a suitable temperature field is designed, tools should be heated or the punch should be cooled; suitable deformation speed should be found to ensure suitable strain rate range. Damage theory considering non-isothermal forming is established. Various modeling methods have been tried to consider above situations. The following situations for modeling the forming process of magnesium alloy sheets and tubes are dealt with: (1) modeling for predicting wrinkling and anisotropy of sheet warm forming; (2) damage theory used for predicting ruptures in sheet warm forming; (3) modeling for optimizing of blank shape and dimensions for sheet warm forming; (4) modeling in non-steady-state creep in hot metal gas forming of AZ31 tubes.

Behavioral Ecology of Captive Species: Using Bibliographic Information to Assess Pet Suitability of Mammal Species

PubMed Central

Koene, Paul; de Mol, Rudi M.; Ipema, Bert

2016-01-01

Which mammal species are suitable to be kept as pet? For answering this question many factors have to be considered. Animals have many adaptations to their natural environment in which they have evolved that may cause adaptation problems and/or risks in captivity. Problems may be visible in behavior, welfare, health, and/or human–animal interaction, resulting, for example, in stereotypies, disease, and fear. A framework is developed in which bibliographic information of mammal species from the wild and captive environment is collected and assessed by three teams of animal scientists. Oneliners from literature about behavioral ecology, health, and welfare and human–animal relationship of 90 mammal species are collected by team 1 in a database and strength of behavioral needs and risks is assessed by team 2. Based on summaries of those strengths the suitability of the mammal species is assessed by team 3. Involvement of stakeholders for supplying bibliographic information and assessments was propagated. Combining the individual and subjective assessments of the scientists using statistical methods makes the final assessment of a rank order of suitability as pet of those species less biased and more objective. The framework is dynamic and produces an initial rank ordered list of the pet suitability of 90 mammal species, methods to add new mammal species to the list or remove animals from the list and a method to incorporate stakeholder assessments. A model is developed that allows for provisional classification of pet suitability. Periodical update of the pet suitability framework is expected to produce an updated list with increased reliability and accuracy. Furthermore, the framework could be further developed to assess the pet suitability of additional species of other animal groups, e.g., birds, reptiles, and amphibians. PMID:27243023

Enhancing the Detectability of Subtle Changes in Multispectral Imagery Through Real-time Change Magnification

DTIC Science & Technology

2015-07-27

remapped to obtain a dynamic  image sequence with a natural color appearance (Hogervorst  et   al .,  2006 ; Hogervorst & Toet, 2010).    2.1.2 Motion...to enhance  the visibility of low‐amplitude temporal (color or location) changes in a standard video sequences  (Wadhwa  et   al ., 2013).  The method...filter scheme, which is highly  suitable to fuse multispectral imagery (Koren  et   al ., 1995; Liu  et   al ., 2001), it can in principle be  incorporated into

Lipidomics by Supercritical Fluid Chromatography

PubMed Central

Laboureur, Laurent; Ollero, Mario; Touboul, David

2015-01-01

This review enlightens the role of supercritical fluid chromatography (SFC) in the field of lipid analysis. SFC has been popular in the late 1980s and 1990s before almost disappearing due to the commercial success of liquid chromatography (LC). It is only 20 years later that a regain of interest appeared when new commercial instruments were introduced. As SFC is fully compatible with the injection of extracts in pure organic solvent, this technique is perfectly suitable for lipid analysis and can be coupled with either highly universal (UV or evaporative light scattering) or highly specific (mass spectrometry) detection methods. A short history of the use of supercritical fluids as mobile phase for the separation oflipids will be introduced first. Then, the advantages and drawbacks of SFC are discussed for each class of lipids (fatty acyls, glycerolipids, glycerophospholipids, sphingolipids, sterols, prenols, polyketides) defined by the LIPID MAPS consortium. PMID:26090714

Complete Imageless solution for overlay front-end manufacturing

NASA Astrophysics Data System (ADS)

Herisson, David; LeCacheux, Virginie; Touchet, Mathieu; Vachellerie, Vincent; Lecarpentier, Laurent; Felten, Franck; Polli, Marco

2005-09-01

Imageless option of KLA-Tencor RDM system (Recipe Data Management) is a new method of recipe creation, using only the mask design to define alignment target and measurement parameters. This technique is potentially the easiest tool to improve recipe management of a large amount of products in logic fab. Overlay recipes are created without wafer, by using a synthetic image (copy of gds mask file) for alignment pattern and target design like shape (frame in frame) and size for the measurement. A complete gauge study on critical CMOS 90nm Gate level has been conducted to evaluate reliability and robustness of the imageless recipe. We show that Imageless limits drastically the number of templates used for recipe creation, and improves or maintains measurement capability compare to manual recipe creation (operator dependant). Imageless appears to be a suitable solution for high volume manufacturing, as shown by the results obtained on production lots.

Transport electron through a quantum wire by side-attached asymmetric quantum-dot rings

NASA Astrophysics Data System (ADS)

Rostami, A.; Zabihi, S.; Rasooli S., H.; Seyyedi, S. K.

2011-12-01

The electronic conductance at zero temperature through a quantum wire with side-attached asymmetric quantum ring (as a scatter system) is theoretically studied using the non-interacting Anderson tunneling Hamiltonian method. We show that the asymmetric configuration of QD- scatter system strongly impresses the amplitude and spectrum of quantum wire nanostructure transmission characteristics. It is shown that whenever the balanced number of quantum dots in two rings is substituted by unbalanced scheme, the number of forbidden mini-bands in quantum wire conductance increases and QW-nanostructure electronic conductance contains rich spectral properties due to appearance of the new anti-resonance and resonance points in spectrum. Considering the suitable gap between nano-rings can strengthen the amplitude of new resonant peaks in the QW conductance spectrum. The proposed asymmetric quantum ring scatter system idea in this paper opens a new insight on designing quantum wire nano structure for given electronic conductance.

Synthesis and applications of MANs/poly(MMA-co-BA) nanocomposite latex by miniemulsion polymerization

PubMed Central

Chen, Huayao; Zhou, Xinhua; Gunasekaran, Sundaram

2017-01-01

We have synthesized core-shell structured 3-methacryloxypropyltrimethoxysilane (MPS) functionalized antimony-doped tin oxide nanoparticles (MANs)–poly(methyl methacrylate-co-butyl acrylate) (PMMA-co-BA, PMB) nanocomposite latex particles via miniemulsion polymerization method. Polymerizable anionic surfactant DNS-86 (allyloxy polyoxyethylene(10) nonyl ammonium sulfate) was first introduced to synthesize core-shell nanocomposite. The morphologies of synthesized MANs and MANs/PMB latex nanocomposite particles were studied with transmission electron microscopy, which revealed particles, on average 70 nm in size, with a core-shell structure. Owing to the uniformity and hydrophobicity of MANs, the MANs-embedded PMB latex nanocomposite can be tailored more precisely than other nanoparticles-embedded nanocomposites. Films incorporating 10 wt% of MANs in the MAN/PMB latex nanocomposite exhibit good transmittance in the visible region, and excellent opacity in the near infrared region. The MANs/PMB nanocomposite film also appears suitable for heat insulation applications. PMID:29291076

Body to Scalp: Evolving Trends in Body Hair Transplantation

PubMed Central

Saxena, Kuldeep; Savant, Sandeep S.

2017-01-01

Follicular unit extraction (FUE) is becoming an increasingly popular method for hair restoration. As FUE leaves behind no linear scars, it is more suitable to harvest from various body areas including beard, chest, and extremities in hirsute individuals. Body hair characteristics such as thickness, length, and hair cycle may not completely match to that of the scalp hair. The techniques of harvesting body hairs are more time consuming, requiring higher degree of skill than regular scalp FUE. Body hair transplantation can be successfully used either alone or in combination with scalp hair in advanced grades of baldness, for improving the cosmetic appearance of hairlines and in scarring alopecia when there is paucity of donor scalp hair. Harvesting of body hairs opens up a new viable donor source for hair restoration surgeons, especially in cases of advanced Norwood grades five and above of androgenetic alopecia. PMID:28584752

Modeling the Dynamic Interrelations between Mobility, Utility, and Land Asking Price

NASA Astrophysics Data System (ADS)

Hidayat, E.; Rudiarto, I.; Siegert, F.; Vries, W. D.

2018-02-01

Limited and insufficient information about the dynamic interrelation among mobility, utility, and land price is the main reason to conduct this research. Several studies, with several approaches, and several variables have been conducted so far in order to model the land price. However, most of these models appear to generate primarily static land prices. Thus, a research is required to compare, design, and validate different models which calculate and/or compare the inter-relational changes of mobility, utility, and land price. The applied method is a combination of analysis of literature review, expert interview, and statistical analysis. The result is newly improved mathematical model which have been validated and is suitable for the case study location. This improved model consists of 12 appropriate variables. This model can be implemented in the Salatiga city as the case study location in order to arrange better land use planning to mitigate the uncontrolled urban growth.

Determination of buoyant density and sensitivity to chloroform and freon for the etiological agent of infectious salmonid anaemia

USGS Publications Warehouse

Christie, K.E.; Hjeltnes, B.; Uglenes , I.; Winton, J.R.

1993-01-01

Plasma was collected from Atlantic salmon Salrno salar with acute infectious salmon anaemia (ISA) and used to challenge Atlantic salmon parr by intraperitoneal injection. Treatment of plasma with the lipid solvent, chloroform, showed that the etiological agent of ISA contained essential lipids, probably as a viral envelope. Some infectivity remained following treatment with freon. Injection challenges using fractions from equilibrium density gradient centrifugation of plasma from fish with acute ISA revealed a band of infectivity in the range 1.184 to 1.262 g cm-3. The band was believed to conta~n both complete ISA-virus particles and infectious particles lacking a complete envelope, nucleocapsid or genome. Density gradient centrifugation of infectious plasma for enrichment of the putative ISA virus appeared to offer a suitable method for obtaining virus-specific nucleic acid for use in the construction of cDNA libraries. 

Approaches to modelling uranium (VI) adsorption on natural mineral assemblages

USGS Publications Warehouse

Waite, T.D.; Davis, J.A.; Fenton, B.R.; Payne, T.E.

2000-01-01

Component additivity (CA) and generalised composite (GC) approaches to deriving a suitable surface complexation model for description of U(VI) adsorption to natural mineral assemblages are pursued in this paper with good success. A single, ferrihydrite-like component is found to reasonably describe uranyl uptake to a number of kaolinitic iron-rich natural substrates at pH > 4 in the CA approach with previously published information on nature of surface complexes, acid-base properties of surface sites and electrostatic effects used in the model. The GC approach, in which little pre-knowledge about generic surface sites is assumed, gives even better fits and would appear to be a method of particular strength for application in areas such as performance assessment provided the model is developed in a careful, stepwise manner with simplicity and goodness of fit as the major criteria for acceptance.

Behaviour of a ZnO thin film as MSG for biosensing material in sub-wavelength regime

NASA Astrophysics Data System (ADS)

Iftimie, N.; Steigmann, R.; Danila, N. A.; Iacomi, F.; Faktorova, D.; Savin, A.

2016-11-01

Zinc oxide nanostructured materials, such as films and nanoparticles, could provide a suitable platform for development of high performance biosensing material due to their unique fundamental material properties. In this study, the enzyme biosensing consisting of a zinc oxide (ZnO) nanoparticles were grown on SiO2/Si substrates by vacuum thermal evaporation method and their sensing characteristics are examined in air and investigated. The film morphology is characterized by X-ray diffraction (XRD) the film crystalline quality and by scanning electron microscopy (SEM). Also, the interest in surface waves appeared due to evanescent waves in the metallic strip grating structure (MSG-Ag/ZnO/SiO2/Si) in sub-wavelength regime. Before testing the sensor with metamaterials (MMs) lens in the sub-wavelength regime, a simulation of the evanescent wave's formation has been performed at the edge of Ag strips, with thicknesses in the range of micrometers.

Synergic in vitro combinations of artemisinin, pyrimethamine and methylene blue against Neospora caninum.

PubMed

Pereira, Luiz Miguel; de Luca, Gabriela; Abichabki, Nathália de Lima Martins; Bronzon da Costa, Cássia Mariana; Yatsuda, Ana Patrícia

2018-01-15

Neospora caninum is a member of Apicomplexa phylum, the causative agent of neosporosis. The neosporosis combat is not well established and several strategies related to vaccine, chemotherapy and immune modulation are under development. In this work, we evaluated the effects of artemisinin (Art), methylene blue (MB) and pyrimethamine (Pyr) alone or associated, on N. caninum proliferation and elimination using LacZ tagged tachyzoites. The reactive oxygen species (ROS) production after incubation with Art were also performed. Our results indicate that combinations of classical antimalarial drugs improve the parasite control, allowing the use of three drugs in a single dose. Additionally, artemisinin demonstrated distinct ROS production patterns in intra and extracellular N. caninum forms. The drug repurposing appears as a suitable approach, allowing a fast and safe method to evaluate old drugs but novel candidates against neosporosis. Copyright © 2017 Elsevier B.V. All rights reserved.

Rapid sucrose monitoring in green coffee samples using multienzymatic biosensor.

PubMed

Stredansky, Miroslav; Redivo, Luca; Magdolen, Peter; Stredansky, Adam; Navarini, Luciano

2018-07-15

Amperometric biosensor utilizing FAD-dependent glucose dehydrogenase (FAD-GDH) for a specific sucrose monitoring in green coffee is described. FAD-GDH was co-immobilized with invertase and mutarotase on a thin-layer gold planar electrode using chitosan. The biosensor showed a wide linearity (from 10 to 1200 μM), low detection limit (8.4 μM), fast response time (50 s), and appeared to be O2 independent. In addition the biosensors exhibited a good operational (3 days) and storage (1 year) stability. Finally, the results achieved from the biosensor measurements of sucrose in 17 samples of green coffee (Coffea arabica, C. canephora and C. liberica) were compared with those obtained by the standard HPLC method. The good correlation among results of real samples, satisfactory analytical performance and simple use of the presented biosensor make it suitable for application in coffee industry. Copyright © 2018 Elsevier Ltd. All rights reserved.

Structural properties and defects of GaN crystals grown at ultra-high pressures: A molecular dynamics simulation

NASA Astrophysics Data System (ADS)

Gao, Tinghong; Li, Yidan; Xie, Quan; Tian, Zean; Chen, Qian; Liang, Yongchao; Ren, Lei; Hu, Xuechen

2018-01-01

The growth of GaN crystals at different pressures was studied by molecular dynamics simulation employing the Stillinger-Weber potential, and their structural properties and defects were characterized using the radial distribution function, the Voronoi polyhedron index method, and a suitable visualization technology. Crystal structures formed at 0, 1, 5, 10, and 20 GPa featured an overwhelming number of <4 0 0 0> Voronoi polyhedra, whereas amorphous structures comprising numerous disordered polyhedra were produced at 50 GPa. During quenching, coherent twin boundaries were easily formed between zinc-blende and wurtzite crystal structures in GaN. Notably, point defects usually appeared at low pressure, whereas dislocations were observed at high pressure, since the simultaneous growth of two crystal grains with different crystal orientations and their boundary expansion was hindered in the latter case, resulting in the formation of a dislocation between these grains.

Evaluation of serum theophylline concentrations following administration of sustained-release beads in applesauce to asthmatic preschool children.

PubMed

Leeder, J S; Robertson, C; Correia, J; Isles, A F; Levison, H; Macleod, S M

1986-02-01

A sustained-release theophylline preparation (Theo-Dur Sprinkle) was evaluated in young asthmatic patients aged 1 to 6 years and receiving a daily dose of 23.4 +/- 2.0 mg/kg (mean +/- SD) to determine, on the basis of serial serum concentrations obtained over a 12-hour dosing interval at steady state, the suitability of such a product in patients likely to metabolize the drug very rapidly. Peak theophylline concentrations of 15.1 +/- 4.1 mg/L were achieved 5.5 +/- 1.5 hours after dosing. The mean maximum to minimum concentration difference was 6.9 +/- 2.2 mg/L for the dosing interval studied. Fluctuations in theophylline concentration less than 100% were achieved in nine of the 12 study patients. Use of the "sprinkle-technique" with Theo-Dur Sprinkle appears to be a simple and effective method of maintaining acceptable fluctuations in serum theophylline concentrations in preschool asthmatic children.

Vectorial model for guided-mode resonance gratings

NASA Astrophysics Data System (ADS)

Fehrembach, A.-L.; Gralak, B.; Sentenac, A.

2018-04-01

We propose a self-consistent vectorial method, based on a Green's function technique, to describe the resonances that appear in guided-mode resonance gratings. The model provides intuitive expressions of the reflectivity and transmittivity matrices of the structure, involving coupling integrals between the modes of a planar reference structure and radiative modes. When one mode is excited, the diffracted field for a suitable polarization can be written as the sum of a resonant and a nonresonant term, thus extending the intuitive approach used to explain the Fano shape of the resonance in scalar configurations. When two modes are excited, we derive a physical analysis in a configuration which requires a vectorial approach. We provide numerical validations of our model. From a technical point of view, we show how the Green's tensor of our planar reference structure can be expressed as two scalar Green's functions, and how to deal with the singularity of the Green's tensor.

An evaluation of the use of ERTS-1 satellite imagery for grizzly bear habitat analysis

NASA Technical Reports Server (NTRS)

Varney, J. R.; Craighead, J. J.; Sumner, J.

1973-01-01

Multispectral scanner images taken by the ERTS-1 satellite in August and October, 1972, were examined to determine if they would be useful in identifying and mapping favorable habitat for grizzly bears. It was possible to identify areas having a suitable mixture of alpine meadow and timber, and to eliminate those which did not meet the isolation requirements of grizzlies because of farming or grazing activity. High altitude timbered areas mapped from satellite imagery agreed reasonably well with the distribution of whitebark pine, an important food species. Analysis of satellite imagery appears to be a valuable supplement to present ground observation methods, since it allows the most important areas to be identified for intensive study and many others to be eliminated from consideration. A sampling plan can be developed from such data which will minimize field effort and overall program cost.

Measuring average angular velocity with a smartphone magnetic field sensor

NASA Astrophysics Data System (ADS)

Pili, Unofre; Violanda, Renante

2018-02-01

The angular velocity of a spinning object is, by standard, measured using a device called a tachometer. However, by directly using it in a classroom setting, the activity is likely to appear as less instructive and less engaging. Indeed, some alternative classroom-suitable methods for measuring angular velocity have been presented. In this paper, we present a further alternative that is smartphone-based, making use of the real-time magnetic field (simply called B-field in what follows) data gathering capability of the B-field sensor of the smartphone device as the timer for measuring average rotational period and average angular velocity. The in-built B-field sensor in smartphones has already found a number of uses in undergraduate experimental physics. For instance, in elementary electrodynamics, it has been used to explore the well-known Bio-Savart law and in a measurement of the permeability of air.

Development of RFI Mitigation Techniques with Digital Beamforming

NASA Technical Reports Server (NTRS)

Bollian, Tobias; Rincon, Rafael; Fatoyinbo, Temilola; Osmanoglu, Batuhan

2016-01-01

Remote sensing radars with longer wavelengths penetrate deeper into the observed scene and are more suitable for the scientific observation of ice sheets or vegetation. Therefore, SAR systems are moving to lower frequencies like L- or P-band. However, as the frequency spectrum is a limited resource, this means that the occupied frequency band has to be shared with existing users. These users can have serious impact on the imaging quality. Radio frequency interference (RFI) that arrives at the antenna together with the SAR backscatter is causing a drop of the signal-to-noise ratio. Despite the high processing gain of the SAR signal, artifacts can appear in the image if the RFI is strong enough. This can lead to a corruption of the acquired data and make it unsuitable for scientific purposes. Hence, the investigation of methods for RFI mitigation is critical to the performance of radar missions and to ensure they meet their main task.

Light elements burning reaction rates at stellar temperatures as deduced by the Trojan Horse measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lamia, L.; Spitaleri, C.; La Cognata, M.

2015-02-24

Experimental nuclear astrophysics aims at determining the reaction rates for astrophysically relevant reactions at their Gamow energies. For charged-particle induced reactions, the access to these energies is usually hindered, in direct measurements, by the presence of the Coulomb barrier between the interacting particles or by electron screening effects, which make hard the determination of the bare-nucleus S(E)-factor of interest for astrophysical codes. The use of the Trojan Horse Method (THM) appears as one of the most suitable tools for investigating nuclear processes of interest for astrophysics. Here, in view of the recent TH measurements, the main destruction channels for deuteriummore » ({sup 2}H), for the two lithium {sup 6,7}Li isotopes, for the {sup 9}Be and the one for the two boron {sup 10,11}B isotopes will be discussed.« less

The use of liquid latex for soot removal from fire scenes and attempted fingerprint development with Ninhydrin.

PubMed

Clutter, Susan Wright; Bailey, Robert; Everly, Jeff C; Mercer, Karl

2009-11-01

Throughout the United States, clearance rates for arson cases remain low due to fire's destructive nature, subsequent suppression, and a misconception by investigators that no forensic evidence remains. Recent research shows that fire scenes can yield fingerprints if soot layers are removed prior to using available fingerprinting processes. An experiment applying liquid latex to sooted surfaces was conducted to assess its potential to remove soot and yield fingerprints after the dried latex was peeled. Latent fingerprints were applied to glass and drywall surfaces, sooted in a controlled burn, and cooled. Liquid latex was sprayed on, dried, and peeled. Results yielded usable prints within the soot prior to removal techniques, but no further fingerprint enhancement was noted with Ninhydrin. Field studies using liquid latex will be continued by the (US) Virginia Fire Marshal Academy but it appears that liquid latex application is a suitable soot removal method for forensic applications.

Photodynamic action of protoporphyrin IX derivatives on Trichophyton rubrum*

PubMed Central

Ramos, Rogério Rodrigo; Kozusny-Andreani, Dora Inês; Fernandes, Adjaci Uchôa; Baptista, Mauricio da Silva

2016-01-01

BACKGROUND Dermatophytes are filamentous keratinophilic fungi. Trichophyton rubrum is a prevalent infectious agent in tineas and other skin diseases. Drug therapy is considered to be limited in the treatment of such infections, mainly due to low accessibility of the drug to the tissue attacked and development of antifungal resistance in these microorganisms. In this context, Photodynamic Therapy is presented as an alternative. OBJECTIVE Evaluate, in vitro, the photodynamic activity of four derivatives of Protoporphyrin IX by irradiation with LED 400 nm in T. rubrum. METHOD Assays were subjected to irradiation by twelve cycles of ten minutes at five minute intervals. RESULT Photodynamic action appeared as effective with total elimination of UFCs from the second irradiation cycle. CONCLUSION Studies show that the photodynamic activity on Trichophyton rubrum relates to a suitable embodiment of the photosensitizer, which can be maximized by functionalization of peripheral groups of the porphyrinic ring. PMID:27192510

Long shelf-life streptavidin support-films suitable for electron microscopy of biological macromolecules

DOE PAGES

Han, Bong-Gyoon; Watson, Zoe; Kang, Hannah; ...

2016-06-15

We describe a rapid and convenient method of growing streptavidin (SA) monolayer crystals directly on holey-carbon EM grids. As expected, these SA monolayer crystals retain their biotin-binding function and crystalline order through a cycle of embedding in trehalose and, later, its removal. This fact allows one to prepare, and store for later use, EM grids on which SA monolayer crystals serve as an affinity substrate for preparing specimens of biological macromolecules. In addition, we report that coating the lipid-tail side of trehalose-embedded monolayer crystals with evaporated carbon appears to improve the consistency with which well-ordered, single crystals are observed tomore » span over entire, 2 μm holes of the support films. Randomly biotinylated 70S ribosomes are used as a test specimen to show that these support films can be used to obtain a high-resolution cryo-EM structure« less

Thermoelectric and magnetic properties of Cr-doped single crystal Bi2Se3 - Search for energy filtering

NASA Astrophysics Data System (ADS)

Cermak, P.; Ruleova, P.; Holy, V.; Prokleska, J.; Kucek, V.; Palka, K.; Benes, L.; Drasar, C.

2018-02-01

Thermoelectric effects are one of the promising ways to utilize waste heat. Novel approaches have appeared in recent decades aiming to enhance thermoelectric conversion. The theory of energy filtering of free carriers by inclusions is among the latest developed methods. Although the basic idea is clear, experimental evidence of this phenomenon is rare. Based on this concept, we searched suitable systems with stable structures showing energy filtering. Here, we report on the anomalous behavior of Cr-doped single-crystal Bi2Se3 that indicates energy filtering. The solubility of chromium in Bi2Se3 was studied, which is the key parameter in the formation process of inclusions. We present recent results on the effect of Cr-doping on the transport coefficients on a wide set of single crystalline samples. Magnetic measurements were used to corroborate the conclusions drawn from the transport and X-ray measurements.

Methods of making copper selenium precursor compositions with a targeted copper selenide content and precursor compositions and thin films resulting therefrom

DOEpatents

Curtis, Calvin J [Lakewood, CO; Miedaner, Alexander [Boulder, CO; van Hest, Marinus Franciscus Antonius Maria; Ginley, David S [Evergreen, CO; Leisch, Jennifer [Denver, CO; Taylor, Matthew [West Simsbury, CT; Stanbery, Billy J [Austin, TX

2011-09-20

Precursor compositions containing copper and selenium suitable for deposition on a substrate to form thin films suitable for semi-conductor applications. Methods of forming the precursor compositions using primary amine solvents and methods of forming the thin films wherein the selection of temperature and duration of heating controls the formation of a targeted species of copper selenide.

Leak and Pipe Detection Method and System

NASA Technical Reports Server (NTRS)

Youngquist, Robert C. (Inventor)

2003-01-01

A method and system for locating leaks of conductive fluids from non-conductive pipes and other structures or for locat- ing non-conductive pipes or structures having conductive fluid contained therein, employ a charge generator to apply a time varying charge to the conductive fluid, and a capaci- tive type detector that can detect the variable charge that is induced in the fluid. The capacitive detector, which prefer- ably includes a handheld housing, employs a large conduc- tive pickup plate that is used to locate the pipe or leak by scanning the plate over the ground and detecting the induced charge that is generated when the plate comes in close proximity to the pipe or leak. If a leak is encountered, the resulting signal will appear over an area larger than expected for a buried pipe, assuming the leak provides an electrically conductive path between the flow and the wet surrounding ground. The detector uses any suitable type of indicator device, such as a pair of headphones that enable an operator to hear the detected signal as a chirping sound, for example.

Multivariate Analysis of the Determinants of the End-Product Quality of Manure-Based Composts and Vermicomposts Using Bayesian Network Modelling.

PubMed

Faverial, Julie; Cornet, Denis; Paul, Jacky; Sierra, Jorge

2016-01-01

Previous studies indicated that the quality of tropical composts is poorer than that of composts produced in temperate regions. The aim of this study was to test the type of manure, the use of co-composting with green waste, and the stabilization method for their ability to improve compost quality in the tropics. We produced 68 composts and vermicomposts that were analysed for their C, lignin and NPK contents throughout the composting process. Bayesian networks were used to assess the mechanisms controlling compost quality. The concentration effect, for C and lignin, and the initial blend quality, for NPK content, were the main factors affecting compost quality. Cattle manure composts presented the highest C and lignin contents, and poultry litter composts exhibited the highest NPK content. Co-composting improved quality by enhancing the concentration effect, which reduced the impact of C and nutrient losses. Vermicomposting did not improve compost quality; co-composting without earthworms thus appears to be a suitable stabilization method under the conditions of this study because it produced high quality composts and is easier to implement.

Pattern Formation

NASA Astrophysics Data System (ADS)

Hoyle, Rebecca

2006-03-01

From the stripes of a zebra and the spots on a leopard's back to the ripples on a sandy beach or desert dune, regular patterns arise everywhere in nature. The appearance and evolution of these phenomena has been a focus of recent research activity across several disciplines. This book provides an introduction to the range of mathematical theory and methods used to analyse and explain these often intricate and beautiful patterns. Bringing together several different approaches, from group theoretic methods to envelope equations and theory of patterns in large-aspect ratio-systems, the book also provides insight behind the selection of one pattern over another. Suitable as an upper-undergraduate textbook for mathematics students or as a fascinating, engaging, and fully illustrated resource for readers in physics and biology, Rebecca Hoyle's book, using a non-partisan approach, unifies a range of techniques used by active researchers in this growing field. Accessible description of the mathematical theory behind fascinating pattern formation in areas such as biology, physics and materials science Collects recent research for the first time in an upper level textbook Features a number of exercises - with solutions online - and worked examples

On the optimization of electromagnetic geophysical data: Application of the PSO algorithm

NASA Astrophysics Data System (ADS)

Godio, A.; Santilano, A.

2018-01-01

Particle Swarm optimization (PSO) algorithm resolves constrained multi-parameter problems and is suitable for simultaneous optimization of linear and nonlinear problems, with the assumption that forward modeling is based on good understanding of ill-posed problem for geophysical inversion. We apply PSO for solving the geophysical inverse problem to infer an Earth model, i.e. the electrical resistivity at depth, consistent with the observed geophysical data. The method doesn't require an initial model and can be easily constrained, according to external information for each single sounding. The optimization process to estimate the model parameters from the electromagnetic soundings focuses on the discussion of the objective function to be minimized. We discuss the possibility to introduce in the objective function vertical and lateral constraints, with an Occam-like regularization. A sensitivity analysis allowed us to check the performance of the algorithm. The reliability of the approach is tested on synthetic, real Audio-Magnetotelluric (AMT) and Long Period MT data. The method appears able to solve complex problems and allows us to estimate the a posteriori distribution of the model parameters.

Ultrasonic Monitoring of the Interaction between Cement Matrix and Alkaline Silicate Solution in Self-Healing Systems.

PubMed

Ait Ouarabi, Mohand; Antonaci, Paola; Boubenider, Fouad; Gliozzi, Antonio S; Scalerandi, Marco

2017-01-07

Alkaline solutions, such as sodium, potassium or lithium silicates, appear to be very promising as healing agents for the development of encapsulated self-healing concretes. However, the evolution of their mechanical and acoustic properties in time has not yet been completely clarified, especially regarding their behavior and related kinetics when they are used in the form of a thin layer in contact with a hardened cement matrix. This study aims to monitor, using linear and nonlinear ultrasonic methods, the evolution of a sodium silicate solution interacting with a cement matrix in the presence of localized cracks. The ultrasonic inspection via linear methods revealed that an almost complete recovery of the elastic and acoustic properties occurred within a few days of healing. The nonlinear ultrasonic measurements contributed to provide further insight into the kinetics of the recovery due to the presence of the healing agent. A good regain of mechanical performance was ascertained through flexural tests at the end of the healing process, confirming the suitability of sodium silicate as a healing agent for self-healing cementitious systems.

Electron microscopy and computed microtomography studies of in vivo implanted mini-TL dosimeters.

PubMed

Strand, S E; Strandh, M; Spanne, P

1993-01-01

The need for direct methods of measuring the absorbed dose in vivo increases for systemic radiation therapy, and in more sophisticated methodologies developed for radioimmunotherapy. One method suggested is the use of mini-thermoluminescent dosimeters (TLD). Recent reports indicate a marked loss of signal when the dosimeters are used in vivo. We investigated the exterior surface of the dosimeters with scanning electron microscopy and the interior dosimeter volume with computed microtomography. The results show that the dosimeters initially have crystals uniformly embedded in the teflon matrix, with some of them directly exposed to the environment. After incubation in gel, holes appear in the dosimeter matrix where the crystals should have been. The computed microtomographic images show that crystals remain in the interior of the matrix, producing the remaining signal. We conclude that these dosimeters should be very carefully handled, and for practical use of mini-TLDs in vivo the dosimeters should be calibrated in equivalent milieus. An alternative solution to the problem of decreased TL efficiency, would be to coat the dosimeters with a thin layer, of Teflon, or other suitable material.

A Novel Finite-Sum Inequality-Based Method for Robust H∞ Control of Uncertain Discrete-Time Takagi-Sugeno Fuzzy Systems With Interval-Like Time-Varying Delays.

PubMed

Zhang, Xian-Ming; Han, Qing-Long; Ge, Xiaohua

2017-09-22

This paper is concerned with the problem of robust H∞ control of an uncertain discrete-time Takagi-Sugeno fuzzy system with an interval-like time-varying delay. A novel finite-sum inequality-based method is proposed to provide a tighter estimation on the forward difference of certain Lyapunov functional, leading to a less conservative result. First, an auxiliary vector function is used to establish two finite-sum inequalities, which can produce tighter bounds for the finite-sum terms appearing in the forward difference of the Lyapunov functional. Second, a matrix-based quadratic convex approach is employed to equivalently convert the original matrix inequality including a quadratic polynomial on the time-varying delay into two boundary matrix inequalities, which delivers a less conservative bounded real lemma (BRL) for the resultant closed-loop system. Third, based on the BRL, a novel sufficient condition on the existence of suitable robust H∞ fuzzy controllers is derived. Finally, two numerical examples and a computer-simulated truck-trailer system are provided to show the effectiveness of the obtained results.

[The most effective dosage in the administration of PGF2-alpha for interruption of pregnancy during the 2d trimester].

PubMed

Herczeg, J; Szontágh, F

1974-06-23

Artificial interruption of pregnancy contains too many risks from the 12th week of pregnancy. The authors have been working at finding the most suitable and effective dosage of prostaglandin for the interruption of pregnancy during the 2nd trimester. The new dosage experimented was 25 mg of prostaglandin F2alpha, followed by another 25 mg 6 hours later. The clinical efficiency of this dosage was tested. This procedures was used in 45 cases. The efficiency of the method was compared to the efficiency of the previously used dosage, which was 25 mg of prostaglandin F2alpha, followed by 25 mg 24 hours later. The new dosage was evaluated 91% efficient, while the previous dosage was found to be 75% efficient. The side effects were rated as acceptable by the patients. There was no case of infection. Two undeniable advantages were found with this new dosage: the duration of the actual procedure is considerably reduced, and the method appears to be much safer. The authors conclude that this new procedure offers numerous clinical advantages.

On beam shaping of the field radiated by a line source coupled to finite or infinite photonic crystals.

PubMed

Ceccuzzi, Silvio; Jandieri, Vakhtang; Baccarelli, Paolo; Ponti, Cristina; Schettini, Giuseppe

2016-04-01

Comparison of the beam-shaping effect of a field radiated by a line source, when an ideal infinite structure constituted by two photonic crystals and an actual finite one are considered, has been carried out by means of two different methods. The lattice sums technique combined with the generalized reflection matrix method is used to rigorously investigate the radiation from the infinite photonic crystals, whereas radiation from crystals composed of a finite number of rods along the layers is analyzed using the cylindrical-wave approach. A directive radiation is observed with the line source embedded in the structure. With an increased separation distance between the crystals, a significant edge diffraction appears that provides the main radiation mechanism in the finite layout. Suitable absorbers are implemented to reduce the above-mentioned diffraction and the reflections at the boundaries, thus obtaining good agreement between radiation patterns of a localized line source coupled to finite and infinite photonic crystals, when the number of periods of the finite structure is properly chosen.

Studies On Endoscopic Local Hyperthermia Using Nd-YAG Laser

NASA Astrophysics Data System (ADS)

Tsunekawa, H.; Kanemaki, N.; Furusawa, A.; Hotta, M.; Kuroiwa, A.; Nishida, M.; Mori, N.; Watanabe, Y.; Morise, K.; Iizuka, A.

1987-03-01

Attempting a new method of laser irradiation for depressed gastric carcinoma, using a newly developed interstitial probe and laser attenuator, we applied local hyperthermia with prolonged low watt contact irradiation. Experimental studies were performed with this probe, using BDF1 mice injected hypodermically with Lewis lung carcinoma. A laser power of 2.0 w at the tip of fiber produced the most desirable temperature curve, about 43 - 60°C at the irradiation site. Clinical applications were carried out on 15 patients with early gastric carcinoma (mainly depressed), 10 preoperative pilot cases and 5 inoperable cases. In follow-up operations and biopsies gastric carcinoma was found to have completely dis-appeared in 2 of the preoperative and 4 of the inoperable cases. In the remaining 8 preoperative cases residual traces of carcinoma were found at the margin of the laser ulcer, but not at the bottom of it. We propose that endoscopic local hyperthermia using interstitial probe and low power irradiation (2.0 W) is the safest and most suitable method of dealing with depressed carcinoma.

In vivo Three-Dimensional Superresolution Fluorescence Tracking using a Double-Helix Point Spread Function

PubMed Central

Lew, Matthew D.; Thompson, Michael A.; Badieirostami, Majid; Moerner, W. E.

2010-01-01

The point spread function (PSF) of a widefield fluorescence microscope is not suitable for three-dimensional super-resolution imaging. We characterize the localization precision of a unique method for 3D superresolution imaging featuring a double-helix point spread function (DH-PSF). The DH-PSF is designed to have two lobes that rotate about their midpoint in any transverse plane as a function of the axial position of the emitter. In effect, the PSF appears as a double helix in three dimensions. By comparing the Cramer-Rao bound of the DH-PSF with the standard PSF as a function of the axial position, we show that the DH-PSF has a higher and more uniform localization precision than the standard PSF throughout a 2 μm depth of field. Comparisons between the DH-PSF and other methods for 3D super-resolution are briefly discussed. We also illustrate the applicability of the DH-PSF for imaging weak emitters in biological systems by tracking the movement of quantum dots in glycerol and in live cells. PMID:20563317

Relative toxicity of products of pyrolysis and combustion of polymeric materials using various test conditions

NASA Technical Reports Server (NTRS)

Hilado, C. J.

1976-01-01

Relative toxicity data for a large number of natural and synthetic polymeric materials are presented which were obtained by 11 pyrolysis and three flaming-combustion test methods. The materials tested include flexible and rigid polyurethane foams, different kinds of fabrics and woods, and a variety of commodity polymers such as polyethylene. Animal exposure chambers of different volumes containing mice, rats, or rabbits were used in the tests, which were performed over the temperature range from ambient to 800 C with and without air flow or recirculation. The test results are found to be sensitive to such variables as exposure mode, temperature, air flow and dilution, material concentration, and animal species, but relative toxicity rankings appear to be similar for many methods and materials. It is concluded that times to incapacitance and to death provide a more suitable basis for relative toxicity rankings than percent mortality alone, that temperature is the most important variable in the tests reported, and that variables such as chamber volume and animal species may not significantly affect the rankings.

21 CFR 640.63 - Suitability of donor.

Code of Federal Regulations, 2010 CFR

2010-04-01

... ADDITIONAL STANDARDS FOR HUMAN BLOOD AND BLOOD PRODUCTS Source Plasma § 640.63 Suitability of donor. (a) Method of determining. The suitability of a donor for Source Plasma shall be determined by a qualified... year. (2)(i) A donor who is to be immunized for the production of high-titer plasma shall be examined...

21 CFR 640.63 - Suitability of donor.

Code of Federal Regulations, 2012 CFR

2012-04-01

... ADDITIONAL STANDARDS FOR HUMAN BLOOD AND BLOOD PRODUCTS Source Plasma § 640.63 Suitability of donor. (a) Method of determining. The suitability of a donor for Source Plasma shall be determined by a qualified... year. (2)(i) A donor who is to be immunized for the production of high-titer plasma shall be examined...

21 CFR 640.63 - Suitability of donor.

Code of Federal Regulations, 2011 CFR

2011-04-01

... ADDITIONAL STANDARDS FOR HUMAN BLOOD AND BLOOD PRODUCTS Source Plasma § 640.63 Suitability of donor. (a) Method of determining. The suitability of a donor for Source Plasma shall be determined by a qualified... year. (2)(i) A donor who is to be immunized for the production of high-titer plasma shall be examined...

21 CFR 640.63 - Suitability of donor.

Code of Federal Regulations, 2013 CFR

2013-04-01

... ADDITIONAL STANDARDS FOR HUMAN BLOOD AND BLOOD PRODUCTS Source Plasma § 640.63 Suitability of donor. (a) Method of determining. The suitability of a donor for Source Plasma shall be determined by a qualified... year. (2)(i) A donor who is to be immunized for the production of high-titer plasma shall be examined...

21 CFR 640.63 - Suitability of donor.

Code of Federal Regulations, 2014 CFR

2014-04-01

... ADDITIONAL STANDARDS FOR HUMAN BLOOD AND BLOOD PRODUCTS Source Plasma § 640.63 Suitability of donor. (a) Method of determining. The suitability of a donor for Source Plasma shall be determined by a qualified... year. (2)(i) A donor who is to be immunized for the production of high-titer plasma shall be examined...

Experimental Evaluation of Suitability of Selected Multi-Criteria Decision-Making Methods for Large-Scale Agent-Based Simulations.

PubMed

Tučník, Petr; Bureš, Vladimír

2016-01-01

Multi-criteria decision-making (MCDM) can be formally implemented by various methods. This study compares suitability of four selected MCDM methods, namely WPM, TOPSIS, VIKOR, and PROMETHEE, for future applications in agent-based computational economic (ACE) models of larger scale (i.e., over 10 000 agents in one geographical region). These four MCDM methods were selected according to their appropriateness for computational processing in ACE applications. Tests of the selected methods were conducted on four hardware configurations. For each method, 100 tests were performed, which represented one testing iteration. With four testing iterations conducted on each hardware setting and separated testing of all configurations with the-server parameter de/activated, altogether, 12800 data points were collected and consequently analyzed. An illustrational decision-making scenario was used which allows the mutual comparison of all of the selected decision making methods. Our test results suggest that although all methods are convenient and can be used in practice, the VIKOR method accomplished the tests with the best results and thus can be recommended as the most suitable for simulations of large-scale agent-based models.

[Extraction method suitable for detection of unheated crustaceans including cephalothorax by ELISA].

PubMed

Shibahara, Yusuke; Yamada, Itta; Uesaka, Yoshihiko; Uneo, Noriko; Abe, Akihisa; Ohashi, Eiji; Shiomi, Kazuo

2009-08-01

When unheated whole samples of crustaceans (shrimp, prawn and crab) were analyzed with our ELISA kit (FA test EIA-Crustacean 'Nissui') using anti-tropomyosin antibodies, a remarkable reduction in reactivity was recognized. This reduction in activity was found to be due to the digestion of tropomyosin during the extraction process by proteases contained in cephalothorax. To avoid the digestion of tropomyosin by proteases, we developed an extraction method (heating method) suitable for the detection of tropomyosin in unheated crustaceans including cephalothorax. Experiments with unheated whole samples of various species of crustaceans confirmed that the heating method greatly improved the low reactivity in the standard method; the heating method gave extraction efficiencies of as high as 93-107%. Various processed crustaceans with cephalothorax, such as dry products (unheated or weakly heated products) and pickles in soy sauce (unheated products), that showed low reactivity with the standard method were confirmed to give superior results with the heating method. These results indicated that the developed heating method is suitable for detecting unheated crustaceans with cephalothorax by means of the ELISA kit.

How many fish? Comparison of two underwater visual sampling methods for monitoring fish communities

PubMed Central

Sini, Maria; Vatikiotis, Konstantinos; Katsoupis, Christos

2018-01-01

Background Underwater visual surveys (UVSs) for monitoring fish communities are preferred over fishing surveys in certain habitats, such as rocky or coral reefs and seagrass beds and are the standard monitoring tool in many cases, especially in protected areas. However, despite their wide application there are potential biases, mainly due to imperfect detectability and the behavioral responses of fish to the observers. Methods The performance of two methods of UVSs were compared to test whether they give similar results in terms of fish population density, occupancy, species richness, and community composition. Distance sampling (line transects) and plot sampling (strip transects) were conducted at 31 rocky reef sites in the Aegean Sea (Greece) using SCUBA diving. Results Line transects generated significantly higher values of occupancy, species richness, and total fish density compared to strip transects. For most species, density estimates differed significantly between the two sampling methods. For secretive species and species avoiding the observers, the line transect method yielded higher estimates, as it accounted for imperfect detectability and utilized a larger survey area compared to the strip transect method. On the other hand, large-scale spatial patterns of species composition were similar for both methods. Discussion Overall, both methods presented a number of advantages and limitations, which should be considered in survey design. Line transects appear to be more suitable for surveying secretive species, while strip transects should be preferred at high fish densities and for species of high mobility. PMID:29942703

A habitat suitability model for Chinese sturgeon determined using the generalized additive method

NASA Astrophysics Data System (ADS)

Yi, Yujun; Sun, Jie; Zhang, Shanghong

2016-03-01

The Chinese sturgeon is a type of large anadromous fish that migrates between the ocean and rivers. Because of the construction of dams, this sturgeon's migration path has been cut off, and this species currently is on the verge of extinction. Simulating suitable environmental conditions for spawning followed by repairing or rebuilding its spawning grounds are effective ways to protect this species. Various habitat suitability models based on expert knowledge have been used to evaluate the suitability of spawning habitat. In this study, a two-dimensional hydraulic simulation is used to inform a habitat suitability model based on the generalized additive method (GAM). The GAM is based on real data. The values of water depth and velocity are calculated first via the hydrodynamic model and later applied in the GAM. The final habitat suitability model is validated using the catch per unit effort (CPUEd) data of 1999 and 2003. The model results show that a velocity of 1.06-1.56 m/s and a depth of 13.33-20.33 m are highly suitable ranges for the Chinese sturgeon to spawn. The hydraulic habitat suitability indexes (HHSI) for seven discharges (4000; 9000; 12,000; 16,000; 20,000; 30,000; and 40,000 m3/s) are calculated to evaluate integrated habitat suitability. The results show that the integrated habitat suitability reaches its highest value at a discharge of 16,000 m3/s. This study is the first to apply a GAM to evaluate the suitability of spawning grounds for the Chinese sturgeon. The study provides a reference for the identification of potential spawning grounds in the entire basin.

Zoom in at African country level: potential climate induced changes in areas of suitability for survival of malaria vectors

PubMed Central

2014-01-01

Background Predicting anopheles vectors’ population densities and boundary shifts is crucial in preparing for malaria risks and unanticipated outbreaks. Although shifts in the distribution and boundaries of the major malaria vectors (Anopheles gambiae s.s. and An. arabiensis) across Africa have been predicted, quantified areas of absolute change in zone of suitability for their survival have not been defined. In this study, we have quantified areas of absolute change conducive for the establishment and survival of these vectors, per African country, under two climate change scenarios and based on our findings, highlight practical measures for effective malaria control in the face of changing climatic patterns. Methods We developed a model using CLIMEX simulation platform to estimate the potential geographical distribution and seasonal abundance of these malaria vectors in relation to climatic factors (temperature, rainfall and relative humidity). The model yielded an eco-climatic index (EI) describing the total favourable geographical locations for the species. The EI values were classified and exported to a GIS package. Using ArcGIS, the EI shape points were clipped to the extent of Africa and then converted to a raster layer using Inverse Distance Weighted (IDW) interpolation method. Generated maps were then transformed into polygon-based geo-referenced data set and their areas computed and expressed in square kilometers (km2). Results Five classes of EI were derived indicating the level of survivorship of these malaria vectors. The proportion of areas increasing or decreasing in level of survival of these malaria vectors will be more pronounced in eastern and southern African countries than those in western Africa. Angola, Ethiopia, Kenya, Mozambique, Tanzania, South Africa and Zambia appear most likely to be affected in terms of absolute change of malaria vectors suitability zones under the selected climate change scenarios. Conclusion The potential shifts of these malaria vectors have implications for human exposure to malaria, as recrudescence of the disease is likely to be recorded in several new areas and regions. Therefore, the need to develop, compile and share malaria preventive measures, which can be adapted to different climatic scenarios, remains crucial. PMID:24885061

Simulation of space radiation effects on polyimide film materials for high temperature applications

NASA Technical Reports Server (NTRS)

Fogdall, L. B.; Cannaday, S. S.

1977-01-01

Space environment effects on candidate materials for the solar sail film are determined. Polymers, including metallized polyimides that might be suitable solar radiation receivers, were exposed to combined proton and solar electromagnetic radiation. Each test sample was weighted, to simulate the tension on the polymer when it is stretched into near-planar shape while receiving solar radiation. Exposure rates up to 16 times that expected in Earth orbit were employed, to simulate near-sun solar sailing conditions. Sample appearance, elongation, and shrinkage were monitored, noted, and documented in situ. Thermosetting polyimides showed less degradation or visual change in appearance than thermoplastics.

Increase in quantity and quality of suitable areas for invasive species as climate changes.

PubMed

Bertelsmeier, Cleo; Luque, Gloria M; Courchamp, Franck

2013-12-01

As climatically suitable range projections become increasingly used to assess distributions of species, we recommend systematic assessments of the quality of habitat in addition to the classical binary classification of habitat. We devised a method to assess occurrence probability, captured by a climatic suitability index, through which we could determine variations in the quality of potential habitat. This relative risk assessment circumvents the use of an arbitrary suitability threshold. We illustrated our method with 2 case studies on invasive ant species. We estimated invasion potential of the destroyer ant (Monomorium destructor) and the European fire ant (Myrmica rubra) on a global scale currently and by 2080 with climate change. We found that 21.1% of the world's landmass currently has a suitable climate for the destroyer ant and 16% has a suitable climate for European fire ant. Our climatic suitability index showed that both ant species would benefit from climate change, but in different ways. The size of the potential distribution increased by 35.8% for the destroyer ant. Meanwhile, the total area of potential distribution remained the same for the European fire ant (>0.05%), but the level of climatic suitability within this range increased greatly and led to an improvement in habitat quality (i.e., of invasive species' establishment likelihood). Either through quantity or quality of suitable areas, both invasive ant species are likely to increase the extent of their invasion in the future, following global climate change. Our results show that species may increase their range if either more areas become suitable or if the available areas present improved suitability. Studies in which an arbitrary suitability threshold was used may overlook changes in area quality within climatically suitable areas and as a result reach incorrect predictions. Incremento de la Cantidad y Calidad de Áreas Idóneas para Especies Invasoras a Medida que Cambia el Clima. © 2013 Society for Conservation Biology.

Raman Spectroscopic Detection for Simulants of Chemical Warfare Agents Using a Spatial Heterodyne Spectrometer.

PubMed

Hu, Guangxiao; Xiong, Wei; Luo, Haiyan; Shi, Hailiang; Li, Zhiwei; Shen, Jing; Fang, Xuejing; Xu, Biao; Zhang, Jicheng

2018-01-01

Raman spectroscopic detection is one of the suitable methods for the detection of chemical warfare agents (CWAs) and simulants. Since the 1980s, many researchers have been dedicated to the research of chemical characteristic of CWAs and simulants and instrumental improvement for their analysis and detection. The spatial heterodyne Raman spectrometer (SHRS) is a new developing instrument for Raman detection that appeared in 2011. It is already well-known that SHRS has the characteristics of high spectral resolution, a large field-of-view, and high throughput. Thus, it is inherently suitable for the analysis and detection of these toxic chemicals and simulants. The in situ and standoff detection of some typical simulants of CWAs, such as dimethyl methylphosphonate (DMMP), diisopropyl methylphosphonate (DIMP), triethylphosphate (TEP), diethyl malonate (DEM), methyl salicylate (MES), 2-chloroethyl ethyl sulfide (CEES), and malathion, were tried. The achieved results show that SHRS does have the ability of in situ analysis or standoff detection for simulants of CWAs. When the laser power was set to as low as 26 mW, the SHRS still has a signal-to-noise ratio higher than 5 in in situ detection. The standoff Raman spectra detection of CWAs simulants was realized at a distance of 11 m. The potential feasibility of standoff detection of SHRS for CWAs simulants has been proved.

Construction of biocompatible porous tissue scaffold from the decellularized umbilical artery.

PubMed

Xin, Yi; Wu, Guanghui; Wu, Man; Zhang, Xiaoxia; Velot, Emilie; Decot, Véronique; Cui, Wei; Huang, Yimin; Stoltz, Jean-Francois; Du, Jie; Li, Na

2015-01-01

The scaffolds prepared from the tissue decellularization conserve the porous 3-D structure and provide an optimal matrix for the tissue regeneration. Since decade, the enzymatic digestion, chemical reagent treatment and mechanical actions such as eversion and abrasion have been used to remove the cells from the intact matrix. In this study, we optimized an enzymatic method to decellularize the umbilical artery to construct a 3-D porous scaffold which is suitable for the culture of mesenchymal stem cells (MSCs). The scaffold maintained the interconnected porous structure. It remained the similar high water content 95.3 ± 1% compared to 94.9 ± 0.6% in the intact umbilical artery (p>0.05). The decellularization process decreased the stress from 0.24 ± 0.05 mPa to 0.15 ± 0.06 mPa (p<0.05). However the decellularization did not change the strain of the artery (45 ± 15% vs. 53 ± 10%, p>0.05). When the scaffold was transplanted to the subcutaneous tissue in the wild type mice, there were less T cells appeared in the surrounding tissue which meant the decreased the immunogenicity by decellularization. This scaffold also supported the adhesion and proliferation of the MSCs. In this study, we constructed a biological compatible porous scaffold from the decellularized umbilical artery which may provide a suitable scaffold for cell-matrix interaction studies and for tissue engineering.

Global estimation of areas with suitable environmental conditions for mariculture species

PubMed Central

Reygondeau, Gabriel; Wabnitz, Colette C. C.; Troell, Max; Cheung, William W. L.

2018-01-01

Aquaculture has grown rapidly over the last three decades expanding at an average annual growth rate of 5.8% (2005–2014), down from 8.8% achieved between 1980 and 2010. The sector now produces 44% of total food fish production. Increasing demand and consumption from a growing global population are driving further expansion of both inland and marine aquaculture (i.e., mariculture, including marine species farmed on land). However, the growth of mariculture is dependent on the availability of suitable farming areas for new facilities, particularly for open farming practices that rely on the natural oceanic environmental parameters such as temperature, oxygen, chlorophyll etc. In this study, we estimated the marine areas within the exclusive economic zones of all countries that were suitable for potential open ocean mariculture activities. To this end, we quantify the environmental niche and inferred the global habitat suitability index (HSI) of the 102 most farmed marine species using four species distribution models. The average weighted HSI across the four models suggests that 72,000,000 km2 of ocean are to be environmentally suitable to farm one or more species. About 92% of the predicted area (66,000,000 km2) is environmentally suitable for farming finfish, 43% (31,000,000 km2) for molluscs and 54% (39,000,000 km2) for crustaceans. These predictions do not consider technological feasibility that can limit crustaceans farming in open waters. Suitable mariculture areas along the Atlantic coast of South America and West Africa appear to be most under-utilized for farming. Our results suggest that factors other than environmental considerations such as the lack of socio-economic and technological capacity, as well as aqua feed supply are currently limiting the potential for mariculture expansion in many areas. PMID:29357374

Selection of suitable fertilizer draw solute for a novel fertilizer-drawn forward osmosis-anaerobic membrane bioreactor hybrid system.

PubMed

Kim, Youngjin; Chekli, Laura; Shim, Wang-Geun; Phuntsho, Sherub; Li, Sheng; Ghaffour, Noreddine; Leiknes, TorOve; Shon, Ho Kyong

2016-06-01

In this study, a protocol for selecting suitable fertilizer draw solute for anaerobic fertilizer-drawn forward osmosis membrane bioreactor (AnFDFOMBR) was proposed. Among eleven commercial fertilizer candidates, six fertilizers were screened further for their FO performance tests and evaluated in terms of water flux and reverse salt flux. Using selected fertilizers, bio-methane potential experiments were conducted to examine the effect of fertilizers on anaerobic activity due to reverse diffusion. Mono-ammonium phosphate (MAP) showed the highest biogas production while other fertilizers exhibited an inhibition effect on anaerobic activity with solute accumulation. Salt accumulation in the bioreactor was also simulated using mass balance simulation models. Results showed that ammonium sulfate and MAP were the most appropriate for AnFDFOMBR since they demonstrated less salt accumulation, relatively higher water flux, and higher dilution capacity of draw solution. Given toxicity of sulfate to anaerobic microorganisms, MAP appears to be the most suitable draw solution for AnFDFOMBR. Copyright © 2016 Elsevier Ltd. All rights reserved.

Selection of suitable e-learning approach using TOPSIS technique with best ranked criteria weights

NASA Astrophysics Data System (ADS)

Mohammed, Husam Jasim; Kasim, Maznah Mat; Shaharanee, Izwan Nizal Mohd

2017-11-01

This paper compares the performances of four rank-based weighting assessment techniques, Rank Sum (RS), Rank Reciprocal (RR), Rank Exponent (RE), and Rank Order Centroid (ROC) on five identified e-learning criteria to select the best weights method. A total of 35 experts in a public university in Malaysia were asked to rank the criteria and to evaluate five e-learning approaches which include blended learning, flipped classroom, ICT supported face to face learning, synchronous learning, and asynchronous learning. The best ranked criteria weights are defined as weights that have the least total absolute differences with the geometric mean of all weights, were then used to select the most suitable e-learning approach by using TOPSIS method. The results show that RR weights are the best, while flipped classroom approach implementation is the most suitable approach. This paper has developed a decision framework to aid decision makers (DMs) in choosing the most suitable weighting method for solving MCDM problems.

ADHD: Is There an App for That? A Suitability Assessment of Apps for the Parents of Children and Young People With ADHD

PubMed Central

Parker, Jack; Harpin, Valerie

2017-01-01

Background Attention-deficit hyperactivity disorder (ADHD) is a highly comorbid disorder that can impact significantly on the individual and their family. ADHD is managed via pharmacological and nonpharmacological interventions. Parents also gain support from parent support groups, which may include chat rooms, as well as face-to-face meetings. With the growth of technology use over recent years, parents have access to more resources that ever before. A number of mobile apps have been developed to help parents manage ADHD in their children and young people. Unfortunately many of these apps are not evidence-based, and little is known of their suitability for the parents or whether they are helpful in ADHD management. Objective The aim of this study was to explore the (1) parents’ views of the suitability of the top ten listed apps for parents of children and young people with ADHD and (2) the views of clinicians that work with them on the suitability and value of the apps. Methods The top 10 listed apps specifically targeted toward the parents of children and young people with ADHD were identified via the Google Play (n=5) and iTunes store (n=5). Interviews were then undertaken with 7 parents of children or young people with ADHD and 6 clinicians who specialize in working with this population to explore their opinions of the 10 apps identified and what they believe the key components are for apps to be suitable and valuable for this population. Results Four themes emerged from clinician and parent interviews: (1) the importance of relating to the app, (2) apps that address ADHD-related difficulties, (3) how the apps can affect family relationships, and (4) apps as an educational tool. Two additional themes emerged from the clinician interviews alone: monitoring ADHD symptoms and that apps should be practical. Parents also identified an additional theme: the importance of the technology. Overall, the characteristics of the current top 10 listed apps did not appear to match well to the views of our sample. Conclusions Findings suggest that these apps may not fully meet the complex needs of this parent population. Further research is required to explore the value of apps with this population and how they can be tailored to their very specific needs. PMID:29030325

Intermittent targeted therapies and stochastic evolution in patients affected by chronic myeloid leukemia

NASA Astrophysics Data System (ADS)

Pizzolato, N.; Persano Adorno, D.; Valenti, D.; Spagnolo, B.

2016-05-01

Front line therapy for the treatment of patients affected by chronic myeloid leukemia (CML) is based on the administration of tyrosine kinase inhibitors, namely imatinib or, more recently, axitinib. Although imatinib is highly effective and represents an example of a successful molecular targeted therapy, the appearance of resistance is observed in a proportion of patients, especially those in advanced stages. In this work, we investigate the appearance of resistance in patients affected by CML, by modeling the evolutionary dynamics of cancerous cell populations in a simulated patient treated by an intermittent targeted therapy. We simulate, with the Monte Carlo method, the stochastic evolution of initially healthy cells to leukemic clones, due to genetic mutations and changes in their reproductive behavior. We first present the model and its validation with experimental data by considering a continuous therapy. Then, we investigate how fluctuations in the number of leukemic cells affect patient response to the therapy when the drug is administered with an intermittent time scheduling. Here we show that an intermittent therapy (IT) represents a valid choice in patients with high risk of toxicity, despite an associated delay to the complete restoration of healthy cells. Moreover, a suitably tuned IT can reduce the probability of developing resistance.

Critical insight into the interaction of naringenin with human haemoglobin: A combined spectroscopic and computational modeling approaches

NASA Astrophysics Data System (ADS)

Maity, Subhajit; Chakraborty, Sandipan; Chakraborti, Abhay Sankar

2017-02-01

The present study demonstrates critical insight into the binding of a bioactive flavanone naringenin with normal human haemoglobin (NHb). Both spectrophotometric and spectrofluorimetric studies reveal that naringenin interacts with NHb. The binding affinity constant and number of binding sites appear to be approximately (1.5 ± 0.2) × 104 M-1 and 1, respectively. Static quenching seems to be an important factor in binding process, as evident from steady-state and time-resolved fluorescence spectroscopic studies. Far UV circular dichroism spectroscopy depicts that binding of naringenin to NHb causes no change in the secondary structure of the protein, which is also evident from Fourier transform infrared spectroscopic study. Free energy change (ΔG0) for naringenin-NHb interaction, determined by spectroscopic and isothermal calorimetric method, appears to be -5.67 kcal/mol and -6.90 kcal/mol, respectively, and is close to the docking energy -6.84 kcal/mol. Molecular docking suggests that naringenin binds near the cavity of the tetrameric heme protein, forming hydrogen bonds with surrounding amino acid residues. The binding site is away from the heme moieties, implicating naringenin binding does not affect the oxygen binding capacity of NHb, which makes the protein a suitable carrier of the flavonoid.

Physicochemical properties of sugar palm starch film: Effect of concentration and plasticizer type

NASA Astrophysics Data System (ADS)

Prasetyo, D. J.; Apriyana, W.; Jatmiko, T. H.; Hernawan; Hayati, S. N.; Rosyida, V. T.; Pranoto, Y.; Poeloengasih, C. D.

2017-07-01

In order to find the best formula for capsule shell production, this present work dealt with exploring physicochemical properties of sugar palm (Arenga pinnata) starch film as a function of different kinds and various concentrations of plasticizers. The films were prepared by casting method at different formula: starch 9-11%, glycerol or sorbitol 35-45% and polyethylene-glycol 400 (PEG 400) 5-9%. Appearance, thickness, retraction ratio, moisture content, swelling behavior and solubility of the film in water were analyzed. Both glycerol and sorbitol are compatible with starch matrix. On the contrary, PEG 400 did not form a film with suitable characteristics. The result reveals that glycerol- and sorbitol-plasticized films appeared translucent, homogenous, smooth and slightly brown in all formulas. Different type and concentration of plasticizers altered the physicochemical of film in different ways. The sorbitol-plasticized film had lower moisture content (≤ 10%) than that of glycerol-plasticized film (≥ 18%). In contrast, film plasticized with sorbitol showed higher solubility in water (28-35%) than glycerol-plasticized film (22-28%). As the concentration of both plasticizers increased, there was an increasing tendency on thickness and solubility in water. Conversely, retraction ratio and swelling degree decreased when both plasticizers concentration increased. In conclusion, the sorbitol-plasticized film showed a potency to be developed as hard capsule material.

ECG telemetry in conscious guinea pigs.

PubMed

Ruppert, Sabine; Vormberge, Thomas; Igl, Bernd-Wolfgang; Hoffmann, Michael

2016-01-01

During preclinical drug development, monitoring of the electrocardiogram (ECG) is an important part of cardiac safety assessment. To detect potential pro-arrhythmic liabilities of a drug candidate and for internal decision-making during early stage drug development an in vivo model in small animals with translatability to human cardiac function is required. Over the last years, modifications/improvements regarding animal housing, ECG electrode placement, and data evaluation have been introduced into an established model for ECG recordings using telemetry in conscious, freely moving guinea pigs. Pharmacological validation using selected reference compounds affecting different mechanisms relevant for cardiac electrophysiology (quinidine, flecainide, atenolol, dl-sotalol, dofetilide, nifedipine, moxifloxacin) was conducted and findings were compared with results obtained in telemetered Beagle dogs. Under standardized conditions, reliable ECG data with low variability allowing largely automated evaluation were obtained from the telemetered guinea pig model. The model is sensitive to compounds blocking cardiac sodium channels, hERG K(+) channels and calcium channels, and appears to be even more sensitive to β-blockers as observed in dogs at rest. QT interval correction according to Bazett and Sarma appears to be appropriate methods in conscious guinea pigs. Overall, the telemetered guinea pig is a suitable model for the conduct of early stage preclinical ECG assessment. Copyright © 2016 Elsevier Inc. All rights reserved.

Multi-criteria Decision Analysis to Model Ixodes ricinus Habitat Suitability.

PubMed

Rousseau, Raphaël; McGrath, Guy; McMahon, Barry J; Vanwambeke, Sophie O

2017-09-01

Tick-borne diseases present a major threat to both human and livestock health throughout Europe. The risk of infection is directly related to the presence of its vector. Thereby it is important to know their distribution, which is strongly associated with environmental factors: the presence and availability of a suitable habitat, of a suitable climate and of hosts. The present study models the habitat suitability for Ixodes ricinus in Ireland, where data on tick distribution are scarce. Tick habitat suitability was estimated at a coarse scale (10 km) with a multi-criteria decision analysis (MCDA) method according to four different scenarios (depending on the variables used and on the weights granted to each of them). The western part of Ireland and the Wicklow mountains in the East were estimated to be the most suitable areas for I. ricinus in the island. There was a good level of agreement between results from the MCDA and recorded tick presence. The different scenarios did not affect the spatial outputs substantially. The current study suggests that tick habitat suitability can be mapped accurately at a coarse scale in a data-scarce context using knowledge-based methods. It can serve as a guideline for future countrywide sampling that would help to determine local risk of tick presence and refining knowledge on tick habitat suitability in Ireland.

Assessing ecoregional-scale habitat suitability index models for priority landbirds

Treesearch

John M. Tirpak; D. Todd Jones-Farrand; Frank R. Thompson; Daniel J. Twedt; Charles K. Baxter; Jane A. Fitzgerald; William B. Uihlein

2009-01-01

Emerging methods in habitat and wildlife population modeling promise new horizons in conservation but only if these methods provide robust population-habitat linkages. We used Breeding Bird Survey (BBS) data to verify and validate newly developed habitat suitability index (HSI) models for 40 priority landbird species in the Central Hardwoods and West Gulf Coastal Plain...

Review methods for image segmentation from computed tomography images

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mamat, Nurwahidah; Rahman, Wan Eny Zarina Wan Abdul; Soh, Shaharuddin Cik

Image segmentation is a challenging process in order to get the accuracy of segmentation, automation and robustness especially in medical images. There exist many segmentation methods that can be implemented to medical images but not all methods are suitable. For the medical purposes, the aims of image segmentation are to study the anatomical structure, identify the region of interest, measure tissue volume to measure growth of tumor and help in treatment planning prior to radiation therapy. In this paper, we present a review method for segmentation purposes using Computed Tomography (CT) images. CT images has their own characteristics that affectmore » the ability to visualize anatomic structures and pathologic features such as blurring of the image and visual noise. The details about the methods, the goodness and the problem incurred in the methods will be defined and explained. It is necessary to know the suitable segmentation method in order to get accurate segmentation. This paper can be a guide to researcher to choose the suitable segmentation method especially in segmenting the images from CT scan.« less

A Way to Select Electrical Sheets of the Segment Stator Core Motors.

NASA Astrophysics Data System (ADS)

Enomoto, Yuji; Kitamura, Masashi; Sakai, Toshihiko; Ohara, Kouichiro

The segment stator core, high density winding coil, high-energy-product permanent magnet are indispensable technologies in the development of a compact and also high efficient motors. The conventional design method for the segment stator core mostly depended on experienced knowledge of selecting a suitable electromagnetic material, far from optimized design. Therefore, we have developed a novel design method in the selection of a suitable electromagnetic material based on the correlation evaluation between the material characteristics and motor performance. It enables the selection of suitable electromagnetic material that will meet the motor specification.

Predicting Fish Growth Potential and Identifying Water Quality Constraints: A Spatially-Explicit Bioenergetics Approach

NASA Astrophysics Data System (ADS)

Budy, Phaedra; Baker, Matthew; Dahle, Samuel K.

2011-10-01

Anthropogenic impairment of water bodies represents a global environmental concern, yet few attempts have successfully linked fish performance to thermal habitat suitability and fewer have distinguished co-varying water quality constraints. We interfaced fish bioenergetics, field measurements, and Thermal Remote Imaging to generate a spatially-explicit, high-resolution surface of fish growth potential, and next employed a structured hypothesis to detect relationships among measures of fish performance and co-varying water quality constraints. Our thermal surface of fish performance captured the amount and spatial-temporal arrangement of thermally-suitable habitat for three focal species in an extremely heterogeneous reservoir, but interpretation of this pattern was initially confounded by seasonal covariation of water residence time and water quality. Subsequent path analysis revealed that in terms of seasonal patterns in growth potential, catfish and walleye responded to temperature, positively and negatively, respectively; crappie and walleye responded to eutrophy (negatively). At the high eutrophy levels observed in this system, some desired fishes appear to suffer from excessive cultural eutrophication within the context of elevated temperatures whereas others appear to be largely unaffected or even enhanced. Our overall findings do not lead to the conclusion that this system is degraded by pollution; however, they do highlight the need to use a sensitive focal species in the process of determining allowable nutrient loading and as integrators of habitat suitability across multiple spatial and temporal scales. We provide an integrated approach useful for quantifying fish growth potential and identifying water quality constraints on fish performance at spatial scales appropriate for whole-system management.

Exploring a suitable nitrogen fertilizer rate to reduce greenhouse gas emissions and ensure rice yields in paddy fields.

PubMed

Zhong, Yiming; Wang, Xiaopeng; Yang, Jingping; Zhao, Xing; Ye, Xinyi

2016-09-15

The application rate of nitrogen fertilizer was believed to dramatically influence greenhouse gas (GHG) emissions from paddy fields. Thus, providing a suitable nitrogen fertilization rate to ensure rice yields, reducing GHG emissions and exploring emission behavior are important issues for field management. In this paper, a two year experiment with six rates (0, 75, 150, 225, 300, 375kgN/ha) of nitrogen fertilizer application was designed to examine GHG emissions by measuring carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O) flux and their cumulative global warming potential (GWP) from paddy fields in Hangzhou, Zhejiang in 2013 and 2014. The results indicated that the GWP and rice yields increased with an increasing application rate of nitrogen fertilizer. Emission peaks of CH4 mainly appeared at the vegetative phase, and emission peaks of CO2, and N2O mainly appeared at reproductive phase of rice growth. The CO2 flux was significantly correlated with soil temperature, while the CH4 flux was influenced by logging water remaining period and N2O flux was significantly associated with nitrogen application rates. This study showed that 225kgN/ha was a suitable nitrogen fertilizer rate to minimize GHG emissions with low yield-scaled emissions of 3.69 (in 2013) and 2.23 (in 2014) kg CO2-eq/kg rice yield as well as to ensure rice yields remained at a relatively high level of 8.89t/ha in paddy fields. Copyright © 2016 Elsevier B.V. All rights reserved.

Development of a highly reliable composite board for printed circuitry for use in space environment

NASA Technical Reports Server (NTRS)

Bradbury, E. J.; Markle, R. A.; Dunnavant, W. R.; Stickney, P. B.

1971-01-01

Materials, processes and fabrication techniques have been investigated for the development of a high-temperature circuit-board laminate. High quality, void-free copper-clad laminates have been made using 7628/HS-1 style fiberglas reinforcements with filled polyimide matrices. The fabricating characteristics of P13N resin appear suitable for use as a filled matrix in this circuit board development. High-fired, ball-milled alumina appears to be necessary to obtain the desired effects in the circuit board system. Nickel-clad copper foil bonding surfaces appear to be another requirement for retention of good bond strengths after art work and plating sequences. The fabrication cycle for this circuit board system is very dependent on the heating profile. Very rapid heating with quick loading is recommended. A stack approach to lamination was successfully used.

Are We "Lucky" for the First Amendment? A Brief History of Students' Right to Read

ERIC Educational Resources Information Center

Kelsey, Marie

2007-01-01

Winter 2007 marked an episode of high anxiety in the library science profession, when the latest Newbery winner, "The Higher Power of Lucky," triggered discussion about words and their suitability for young readers. It seems that the entire world now knows that the word "scrotum" appears on the first page of the book. School…

Darwin and Evolution: A Set of Activities Based on the Evolution of Mammals

ERIC Educational Resources Information Center

Haresnape, Janet M.

2010-01-01

These activities, prepared for key stage 5 students (ages 16-18) and also suitable for key stage 4 (ages 14-16), show that physical appearance is not necessarily the best way to classify mammals. DNA structure is examined to show how similarities and differences between DNA sequences of mammals can be used to establish evolutionary relationships.…

Using the ribosome to synthesize peptidomimetics

PubMed Central

2009-01-01

Peptidomimetic research is an approach to identify peptide-based drugs designed to mimic structural, conformational, and biological properties of peptides while overcoming their limitations, such as protease instability and poor cell penetration. With recent advances in ribosomal synthesis of peptides containing unnatural amino acids, this technology appears suitable for preparing large structurally diverse libraries of peptidomimetics for drug discovery screening. PMID:20948631

Development and Validation of an Instrument to Assess Student Attitudes toward Science across Grades 5 through 10

ERIC Educational Resources Information Center

Summers, Ryan; Abd-El-Khalick, Fouad

2018-01-01

The aim of the present study is to enable future studies into students' attitudes toward science, and related constructs, by developing and validating an instrument suitable for cross-sectional designs. Following a thorough review of the literature it was determined that many extant instruments included design aspects that appeared to be limited…

Multiscale habitat relationships of stream amphibians in the Klamath-Siskiyou region of California and Oregon

Treesearch

Hartwell H. Welsh Jr; Amy J. Lind

2002-01-01

Regional amphibian distribution patterns can vary greatly depending on species and the spatial scale of inquiry (e.g., landscape to microenvironment). These differences appear to be related both to habitat selection among species as well as availability of suitable habitats across scales. We sampled amphibians in 39 second- and third-order streams in the conifer-...

Practical considerations for measuring hydrogen concentrations in groundwater

USGS Publications Warehouse

Chapelle, F.H.; Vroblesky, D.A.; Woodward, J.C.; Lovley, D.R.

1997-01-01

Several practical considerations for measuring concentrations of dissolved molecular hydrogen (H2) in groundwater including 1 sampling methods 2 pumping methods and (3) effects of well casing materials were evaluated. Three different sampling methodologies (a downhole sampler, a gas- stripping method, and a diffusion sampler) were compared. The downhole sampler and gas-stripping methods gave similar results when applied to the same wells, the other hand, appeared to The diffusion sampler, on overestimate H2 concentrations relative to the downhole sampler. Of these methods, the gas-stripping method is better suited to field conditions because it is faster (~ 30 min for a single analysis as opposed to 2 h for the downhole sampler or 8 h for the diffusion sampler), the analysis is easier (less sample manipulation is required), and the data computations are more straightforward (H2 concentrations need not be corrected for water sample volume). Measurement of H2 using the gas-stripping method can be affected by different pumping equipment. Peristaltic, piston, and bladder pumps all gave similar results when applied to water produced from the same well. It was observed, however, that peristaltic-pumped water (which draws water under a negative pressure) enhanced the gas-stripping process and equilibrated slightly faster than either piston or bladder pumps (which push water under a positive pressure). A direct current(dc) electrically driven submersible pump was observed to produce H2 and was not suitable for measuring H2 in groundwater. Measurements from two field sites indicate that iron or steel well casings, produce H2, which masks H2 concentrations in groundwater. PVC-cased wells or wells cased with other materials that do not produce H2 are necessary for measuring H2 concentrations in groundwater.Several practical considerations for measuring concentrations of dissolved molecular hydrogen in groundwater including sampling methods, pumping methods, and effects of well casing materials were evaluated. The downhole sampler and gas-stripping methods gave similar results when applied to the same wells. The diffusional sampler appears to overestimate H2 concentrations relative to the downhole sampler. Gas-stripping method is better for a single analysis and the data computations are more straightforward. Measurement of H2 using the gas-stripping method can be affected by different pumping equipment.

Matrix-Assisted Laser Desorption/Ionization Time-of-Flight Mass-Spectrometry (MALDI-TOF MS) Based Microbial Identifications: Challenges and Scopes for Microbial Ecologists

PubMed Central

Rahi, Praveen; Prakash, Om; Shouche, Yogesh S.

2016-01-01

Matrix-assisted laser desorption/ionization time-of-flight mass-spectrometry (MALDI-TOF MS) based biotyping is an emerging technique for high-throughput and rapid microbial identification. Due to its relatively higher accuracy, comprehensive database of clinically important microorganisms and low-cost compared to other microbial identification methods, MALDI-TOF MS has started replacing existing practices prevalent in clinical diagnosis. However, applicability of MALDI-TOF MS in the area of microbial ecology research is still limited mainly due to the lack of data on non-clinical microorganisms. Intense research activities on cultivation of microbial diversity by conventional as well as by innovative and high-throughput methods has substantially increased the number of microbial species known today. This important area of research is in urgent need of rapid and reliable method(s) for characterization and de-replication of microorganisms from various ecosystems. MALDI-TOF MS based characterization, in our opinion, appears to be the most suitable technique for such studies. Reliability of MALDI-TOF MS based identification method depends mainly on accuracy and width of reference databases, which need continuous expansion and improvement. In this review, we propose a common strategy to generate MALDI-TOF MS spectral database and advocated its sharing, and also discuss the role of MALDI-TOF MS based high-throughput microbial identification in microbial ecology studies. PMID:27625644

Approaching Etuaptmumk – introducing a consensus-based mixed method for health services research

PubMed Central

Chatwood, Susan; Paulette, Francois; Baker, Ross; Eriksen, Astrid; Hansen, Ketil Lenert; Eriksen, Heidi; Hiratsuka, Vanessa; Lavoie, Josée; Lou, Wendy; Mauro, Ian; Orbinski, James; Pabrum, Nathalie; Retallack, Hanna; Brown, Adalsteinn

2015-01-01

With the recognized need for health systems’ improvements in the circumpolar and indigenous context, there has been a call to expand the research agenda across all sectors influencing wellness and to recognize academic and indigenous knowledge through the research process. Despite being recognized as a distinct body of knowledge in international forums and across indigenous groups, examples of methods and theories based on indigenous knowledge are not well documented in academic texts or peer-reviewed literature on health systems. This paper describes the use of a consensus-based, mixed method with indigenous knowledge by an experienced group of researchers and indigenous knowledge holders who collaborated on a study that explored indigenous values underlying health systems stewardship. The method is built on the principles of Etuaptmumk or two-eyed seeing, which aim to respond to and resolve the inherent conflicts between indigenous ways of knowing and the scientific inquiry that informs the evidence base in health care. Mixed methods’ frameworks appear to provide a framing suitable for research questions that require data from indigenous knowledge sources and western knowledge. The nominal consensus method, as a western paradigm, was found to be responsive to embedding of indigenous knowledge and allowed space to express multiple perspectives and reach consensus on the question at hand. Further utilization and critical evaluation of this mixed methodology with indigenous knowledge are required. PMID:26004427

Solutions of some problems in applied mathematics using MACSYMA

NASA Technical Reports Server (NTRS)

Punjabi, Alkesh; Lam, Maria

1987-01-01

Various Symbolic Manipulation Programs (SMP) were tested to check the functioning of their commands and suitability under various operating systems. Support systems for SMP were found to be relatively better than the one for MACSYMA. The graphics facilities for MACSYMA do not work as expected under the UNIX operating system. Not all commands for MACSYMA function as described in the manuals. Shape representation is a central issue in computer graphics and computer-aided design. Aside from appearance, there are other application dependent, desirable properties like continuity to certain order, symmetry, axis-independence, and variation-diminishing properties. Several shape representations are studied, which include the Osculatory Method, a Piecewise Cubic Polynomial Method using two different slope estimates, Piecewise Cubic Hermite Form, a method by Harry McLaughlin, and a Piecewise Bezier Method. They are applied to collected physical and chemical data. Relative merits and demerits of these methods are examined. Kinematics of a single link, non-dissipative robot arm is studied using MACSYMA. Lagranian is set-up and Lagrange's equations are derived. From there, Hamiltonian equations of motion are obtained. Equations suggest that bifurcation of solutions can occur, depending upon the value of a single parameter. Using the characteristic function W, the Hamilton-Jacobi equation is derived. It is shown that the H-J equation can be solved in closed form. Analytical solutions to the H-J equation are obtained.

Validation of miRNA genes suitable as reference genes in qPCR analyses of miRNA gene expression in Atlantic salmon (Salmo salar).

PubMed

Johansen, Ilona; Andreassen, Rune

2014-12-23

MicroRNAs (miRNAs) are an abundant class of endogenous small RNA molecules that downregulate gene expression at the post-transcriptional level. They play important roles by regulating genes that control multiple biological processes, and recent years there has been an increased interest in studying miRNA genes and miRNA gene expression. The most common method applied to study gene expression of single genes is quantitative PCR (qPCR). However, before expression of mature miRNAs can be studied robust qPCR methods (miRNA-qPCR) must be developed. This includes identification and validation of suitable reference genes. We are particularly interested in Atlantic salmon (Salmo salar). This is an economically important aquaculture species, but no reference genes dedicated for use in miRNA-qPCR methods has been validated for this species. Our aim was, therefore, to identify suitable reference genes for miRNA-qPCR methods in Salmo salar. We used a systematic approach where we utilized similar studies in other species, some biological criteria, results from deep sequencing of small RNAs and, finally, experimental validation of candidate reference genes by qPCR to identify the most suitable reference genes. Ssa-miR-25-3p was identified as most suitable single reference gene. The best combinations of two reference genes were ssa-miR-25-3p and ssa-miR-455-5p. These two genes were constitutively and stably expressed across many different tissues. Furthermore, infectious salmon anaemia did not seem to affect their expression levels. These genes were amplified with high specificity, good efficiency and the qPCR assays showed a good linearity when applying a simple cybergreen miRNA-PCR method using miRNA gene specific forward primers. We have identified suitable reference genes for miRNA-qPCR in Atlantic salmon. These results will greatly facilitate further studies on miRNA genes in this species. The reference genes identified are conserved genes that are identical in their mature sequence in many aquaculture species. Therefore, they may also be suitable as reference genes in other teleosts. Finally, the systematic approach used in our study successfully identified suitable reference genes, suggesting that this may be a useful strategy to apply in similar validation studies in other aquaculture species.

Noise induced phenomena in combustion

NASA Astrophysics Data System (ADS)

Liu, Hongliang

Quantitative models of combustion usually consist of systems of deterministic differential equations. However, there are reasons to suspect that noise may have a significant influence. In this thesis, our primary objective is to study the effect of noise on measurable quantities in the combustion process. Our first study involves combustion in a homogeneous gas. With a one step reaction model, we analytically estimate the requirements under which noise is important to create significant differences. Our simulation shows that a bi-modality phenomenon appears when appropriate parameters are applied, which agrees with our analytical result. Our second study involves steady planar flames. We use a relatively complete chemical model of the H2/air reaction system, which contains all eight reactive species (H2, O2, H, O, OH, H2O, HO2, H2O2) and N2. Our mathematical model for this system is a reacting flow model. We derive noise terms related to transport processes by a method advocated by Landau & Lifshitz, and we also derive noise terms related to chemical reactions. We develop a code to simulate this system. The numerical implementation relies on a good Riemann solver, suitable initial and boundary conditions, and so on. We also implement a code on a continuation method, which not only can be used to study approximate properties of laminar flames under deterministic governing equations, but also eliminates the difficulty of providing a suitable initial condition for governing equations with noise. With numerical experiments, we find the difference of flame speed exist when the noise is turned on or off although it is small when compared with the influence of other parameters, for example, the equivalence ratio. It will be a starting point for further studies to include noise in combustion.

Assessing Non-Technical Site Suitability Criteria for Stormwater Capture, Treatment and Recharge

NASA Astrophysics Data System (ADS)

Eisenstein, W.

2016-12-01

This presentation will describe a new method for assessing non-technical site suitability criteria for the siting of stormwater capture, treatment and recharge (or stormwater CTR) facilities in Sonoma County, California, USA. "Non-technical site suitability criteria" include issues such as community acceptance, aesthetics, nuisances and hazards, and compatibility with neighboring land uses, and are distinguished from "technical criteria" such as hydrology and soil characteristics that are the traditional subject of suitability analyses. Non-technical criteria are rarely, if ever, considered in formal siting suitability studies conducted by agencies and municipalities, yet can be fatal to the prospects of a given project's construction if not identified and mitigated. The researchers developed a new method for identifying and spatially characterizing relevant non-technical criteria through interviews and questionnaires with community stakeholders, and introducing those criteria into a spatial multi-criteria decision analysis framework that assesses site suitabilty across a study watershed (the Upper Petaluma River watershed in Sonoma County).

An approach for land suitability evaluation using geostatistics, remote sensing, and geographic information system in arid and semiarid ecosystems.

PubMed

Emadi, Mostafa; Baghernejad, Majid; Pakparvar, Mojtaba; Kowsar, Sayyed Ahang

2010-05-01

This study was undertaken to incorporate geostatistics, remote sensing, and geographic information system (GIS) technologies to improve the qualitative land suitability assessment in arid and semiarid ecosystems of Arsanjan plain, southern Iran. The primary data were obtained from 85 soil samples collected from tree depths (0-30, 30-60, and 60-90 cm); the secondary information was acquired from the remotely sensed data from the linear imaging self-scanner (LISS-III) receiver of the IRS-P6 satellite. Ordinary kriging and simple kriging with varying local means (SKVLM) methods were used to identify the spatial dependency of soil important parameters. It was observed that using the data collected from the spectral values of band 1 of the LISS-III receiver as the secondary variable applying the SKVLM method resulted in the lowest mean square error for mapping the pH and electrical conductivity (ECe) in the 0-30-cm depth. On the other hand, the ordinary kriging method resulted in a reliable accuracy for the other soil properties with moderate to strong spatial dependency in the study area for interpolation in the unstamped points. The parametric land suitability evaluation method was applied on the density points (150 x 150 m(2)) instead of applying on the limited representative profiles conventionally, which were obtained by the kriging or SKVLM methods. Overlaying the information layers of the data was used with the GIS for preparing the final land suitability evaluation. Therefore, changes in land characteristics could be identified in the same soil uniform mapping units over a very short distance. In general, this new method can easily present the squares and limitation factors of the different land suitability classes with considerable accuracy in arbitrary land indices.

ISRU Production of Life Support Consumables for a Lunar Base

NASA Technical Reports Server (NTRS)

Cooper, Bonnie L.; Simon, Tom

2007-01-01

Similar to finding a home on Earth, location is important when selecting where to set up an exploration outpost. Essential considerations for comparing potential lunar outpost locations include: (1) areas nearby that would be useful for In-Situ Resource Utilization (ISRU) oxygen extraction from regolith for crew breathing oxygen as well as other potential uses; (2) proximity to a suitable landing site; (3) availability of sunlight; (4) capability for line-of-sight communications with Earth; (5) proximity to permanently-shadowed areas for potential in-situ water ice; and (6) scientific interest. The Mons Malapert1 (Malapert Mountain) area (85.5degS, 0degE) has been compared to these criteria, and appears to be a suitable location for a lunar outpost.

Determination of mechanical properties of some glass fiber reinforced plastics suitable to Wind Turbine Blade construction

NASA Astrophysics Data System (ADS)

Steigmann, R.; Savin, A.; Goanta, V.; Barsanescu, P. D.; Leitoiu, B.; Iftimie, N.; Stanciu, M. D.; Curtu, I.

2016-08-01

The control of wind turbine's components is very rigorous, while the tower and gearbox have more possibility for revision and repairing, the rotor blades, once they are deteriorated, the defects can rapidly propagate, producing failure, and the damages can affect large regions around the wind turbine. This paper presents the test results, performed on glass fiber reinforced plastics (GFRP) suitable to construction of wind turbine blades (WTB). The Young modulus, shear modulus, Poisson's ratio, ultimate stress have been determined using tensile and shear tests. Using Dynamical Mechanical Analysis (DMA), the activation energy for transitions that appear in polyester matrix as well as the complex elastic modulus can be determined, function of temperature.

Exploring the handshake in employment interviews.

PubMed

Stewart, Greg L; Dustin, Susan L; Barrick, Murray R; Darnold, Todd C

2008-09-01

The authors examined how an applicant's handshake influences hiring recommendations formed during the employment interview. A sample of 98 undergraduate students provided personality measures and participated in mock interviews during which the students received ratings of employment suitability. Five trained raters independently evaluated the quality of the handshake for each participant. Quality of handshake was related to interviewer hiring recommendations. Path analysis supported the handshake as mediating the effect of applicant extraversion on interviewer hiring recommendations, even after controlling for differences in candidate physical appearance and dress. Although women received lower ratings for the handshake, they did not on average receive lower assessments of employment suitability. Exploratory analysis suggested that the relationship between a firm handshake and interview ratings may be stronger for women than for men.

Quantification of fungal abundance on cultural heritage using real time PCR targeting the β-actin gene

PubMed Central

Ettenauer, Jörg; Piñar, Guadalupe; Tafer, Hakim; Sterflinger, Katja

2014-01-01

The traditional methodology used for the identification of microbes colonizing our cultural heritage was the application of cultivation methods and/or microscopy. This approach has many advantages, as living microorganisms may be obtained for physiological investigations. In addition, these techniques allow the quantitative and qualitative assessment of the investigated environment. Quantitative analyses are done by plate count and the determination of abundance by the colony forming unit (CFU). Nevertheless, these techniques have many drawbacks that lead to an underestimation of the cell numbers and do not provide a comprehensive overview of the composition of the inhabiting microbiota. In the last decades, several molecular techniques have been developed enabling many advantages over the cultivation approach. Mainly PCR-based, fingerprinting techniques allow a qualitative detection and identification of the microbiota. In this study, we developed a real time PCR method as a simple, rapid and reliable tool to detect and quantify fungal abundance using the β-actin gene, which is known to appear as a single-copy gene in fungi. To this end, five different indoor thermal insulation materials applied for historical buildings that were previously tested for their bio-susceptibility against various fungi were subjected to qPCR analyses. The obtained results were compared with those obtained from a previous study investigating the bio-susceptibility of the insulation materials using classical cultivation experiments. Both results correlated well, revealing that Perlite plaster was the most suitable insulation material, showing the lowest fungal CFU and qPCR values. In contrast, insulations made of wood showed to be not recommendable from the microbiological point of view. In addition, the potential of qPCR was tested in other materials of cultural heritage, as old parchments, showing to be a suitable method for measuring fungal abundance in these delicate materials. PMID:24904567

Classification of glioblastoma and metastasis for neuropathology intraoperative diagnosis: a multi-resolution textural approach to model the background

NASA Astrophysics Data System (ADS)

Ahmad Fauzi, Mohammad Faizal; Gokozan, Hamza Numan; Elder, Brad; Puduvalli, Vinay K.; Otero, Jose J.; Gurcan, Metin N.

2014-03-01

Brain cancer surgery requires intraoperative consultation by neuropathology to guide surgical decisions regarding the extent to which the tumor undergoes gross total resection. In this context, the differential diagnosis between glioblastoma and metastatic cancer is challenging as the decision must be made during surgery in a short time-frame (typically 30 minutes). We propose a method to classify glioblastoma versus metastatic cancer based on extracting textural features from the non-nuclei region of cytologic preparations. For glioblastoma, these regions of interest are filled with glial processes between the nuclei, which appear as anisotropic thin linear structures. For metastasis, these regions correspond to a more homogeneous appearance, thus suitable texture features can be extracted from these regions to distinguish between the two tissue types. In our work, we use the Discrete Wavelet Frames to characterize the underlying texture due to its multi-resolution capability in modeling underlying texture. The textural characterization is carried out in primarily the non-nuclei regions after nuclei regions are segmented by adapting our visually meaningful decomposition segmentation algorithm to this problem. k-nearest neighbor method was then used to classify the features into glioblastoma or metastasis cancer class. Experiment on 53 images (29 glioblastomas and 24 metastases) resulted in average accuracy as high as 89.7% for glioblastoma, 87.5% for metastasis and 88.7% overall. Further studies are underway to incorporate nuclei region features into classification on an expanded dataset, as well as expanding the classification to more types of cancers.

Development and validation of a high throughput assay for the quantification of multiple green tea-derived catechins in human plasma.

PubMed

Mawson, Deborah H; Jeffrey, Keon L; Teale, Philip; Grace, Philip B

2018-06-19

A rapid, accurate and robust method for the determination of catechin (C), epicatechin (EC), gallocatechin (GC), epigallocatechin (EGC), catechin gallate (Cg), epicatechin gallate (ECg), gallocatechin gallate (GCg) and epigallocatechin gallate (EGCg) concentrations in human plasma has been developed. The method utilises protein precipitation following enzyme hydrolysis, with chromatographic separation and detection using reversed-phase liquid chromatography - tandem mass spectrometry (LC-MS/MS). Traditional issues such as lengthy chromatographic run times, sample and extract stability, and lack of suitable internal standards have been addressed. The method has been evaluated using a comprehensive validation procedure, confirming linearity over appropriate concentration ranges, and inter/intra batch precision and accuracies within suitable thresholds (precisions within 13.8% and accuracies within 12.4%). Recoveries of analytes were found to be consistent between different matrix samples, compensated for using suitable internal markers and within the performance of the instrumentation used. Similarly, chromatographic interferences have been corrected using the internal markers selected. Stability of all analytes in matrix is demonstrated over 32 days and throughout extraction conditions. This method is suitable for high throughput sample analysis studies. This article is protected by copyright. All rights reserved.

Using the spectral induced polarization method to assess biochar performance as a remediation agent

NASA Astrophysics Data System (ADS)

Ntarlagiannis, D.; Kirmizakis, P.; Kalderis, D.; Soupios, P. M.

2016-12-01

Olive mill waste-water (OMW), the waste product of olive oil production, typically holds a high concentration of hazardous substances (e.g. phenols) to humans and the environment. OMW is usually disposed of into unregulated, not properly constructed, evaporation ponds in the close vicinity of the olive mil. Efficient, easy to apply, remediation methods are sought to address the impact of uncontrolled OMW in the Mediterranean region. Biochar amended soils could be used to reduce the detrimental effects of OMW since it has been shown to reduce the organic load of impacted soils. We present results from a laboratory experiment designed [a] to treat OMW using biochar, and [b] utilize the spectral induced polarization (SIP) method to monitor the remediation process. Three biochar amended columns (5%, 10%, 25%) and one control were saturated with OMW from the Alikianos waste pond. After 10 day treatment the organic load was reduced on all biochar amended columns, with the 10% showing the highest reduction. Early results indicate aerobic degradation at the initial treatment stages, followed by anaerobic conditions later. SIP monitoring provides some very interesting results, with the real and imaginary components behaving differently. The real conductivity appears to increase significantly only for the 10% biochar column, the one with highest organic load removal. Imaginary conductivity appears to increase with time in all biochar amended columns, and it seems to be affected by the amount of biochar present. Finally, scaning electron microscopy (SEM) showed no alterations on the physical structure of the biochar, potentially allowing for multiple treatments and/or re-using. These early results suggest that biochar is suitable for OMW treatment, and SIP is sensitive to the remediation processes. Overall, the method is simple to set-up, run and monitor and does not require any safety precautions. Further geochemical analysis is performed to provide additional insight on OMW and biochar processes, and their links to SIP responses.

Quality of life assessment in cosmetics: specificity and interest of the international BeautyQol instrument.

PubMed

Beresniak, Ariel; Auray, Jean-Paul; Duru, Gérard; Aractingi, Selim; Krueger, Gerald G; Talarico, Sergio; Tsutani, Kiichiro; Dupont, Danielle; de Linares, Yolaine

2015-09-01

The wide use of cosmetics and their perceived benefits upon well-being imply objective descriptions of their effects upon the different dimensions contributing to the quality of life (QoL). Such a goal pleas for using relevant and validated scientific instruments with robust measurement methods. This paper discusses the interest of the new validated questionnaire BeautyQoL specifically designed to assess the effect of cosmetic products on physical appearance and QoL. After conducting a review of skin appearance and QoL, three phases of the international codevelopment have been carried out in the following sequence: semi-directed interviews (Phase 1), acceptability study (Phase 2), and validation study (Phase 3). Data collection and validation process have been carried out in 16 languages. This review confirms that QoL instruments developed in dermatology are not suitable to assess cosmetic products, mainly because of their lack of sensitivity. General acceptability of BeautyQol was very good. Forty-two questions have been structured in five dimensions that explained 76.7% of the total variance: Social Life, Self-confidence, Mood, Vitality, and Attractiveness. Cronbach's alpha coefficients are between 0.932 and 0.978, confirming the good internal consistency of the results. The BeautyQol questionnaire is the first international instrument specific to cosmetic products and physical appearance that has been validated in 16 languages and could be used in a number of clinical trials and descriptive studies to demonstrate the added value of these products on the QoL. © 2015 Wiley Periodicals, Inc.

Modeling ocean wave propagation under sea ice covers

NASA Astrophysics Data System (ADS)

Zhao, Xin; Shen, Hayley H.; Cheng, Sukun

2015-02-01

Operational ocean wave models need to work globally, yet current ocean wave models can only treat ice-covered regions crudely. The purpose of this paper is to provide a brief overview of ice effects on wave propagation and different research methodology used in studying these effects. Based on its proximity to land or sea, sea ice can be classified as: landfast ice zone, shear zone, and the marginal ice zone. All ice covers attenuate wave energy. Only long swells can penetrate deep into an ice cover. Being closest to open water, wave propagation in the marginal ice zone is the most complex to model. The physical appearance of sea ice in the marginal ice zone varies. Grease ice, pancake ice, brash ice, floe aggregates, and continuous ice sheet may be found in this zone at different times and locations. These types of ice are formed under different thermal-mechanical forcing. There are three classic models that describe wave propagation through an idealized ice cover: mass loading, thin elastic plate, and viscous layer models. From physical arguments we may conjecture that mass loading model is suitable for disjoint aggregates of ice floes much smaller than the wavelength, thin elastic plate model is suitable for a continuous ice sheet, and the viscous layer model is suitable for grease ice. For different sea ice types we may need different wave ice interaction models. A recently proposed viscoelastic model is able to synthesize all three classic models into one. Under suitable limiting conditions it converges to the three previous models. The complete theoretical framework for evaluating wave propagation through various ice covers need to be implemented in the operational ocean wave models. In this review, we introduce the sea ice types, previous wave ice interaction models, wave attenuation mechanisms, the methods to calculate wave reflection and transmission between different ice covers, and the effect of ice floe breaking on shaping the sea ice morphology. Laboratory experiments, field measurements and numerical simulations supporting the fundamental research in wave-ice interaction models are discussed. We conclude with some outlook of future research needs in this field.

Experimental Evaluation of Suitability of Selected Multi-Criteria Decision-Making Methods for Large-Scale Agent-Based Simulations

PubMed Central

2016-01-01

Multi-criteria decision-making (MCDM) can be formally implemented by various methods. This study compares suitability of four selected MCDM methods, namely WPM, TOPSIS, VIKOR, and PROMETHEE, for future applications in agent-based computational economic (ACE) models of larger scale (i.e., over 10 000 agents in one geographical region). These four MCDM methods were selected according to their appropriateness for computational processing in ACE applications. Tests of the selected methods were conducted on four hardware configurations. For each method, 100 tests were performed, which represented one testing iteration. With four testing iterations conducted on each hardware setting and separated testing of all configurations with the–server parameter de/activated, altogether, 12800 data points were collected and consequently analyzed. An illustrational decision-making scenario was used which allows the mutual comparison of all of the selected decision making methods. Our test results suggest that although all methods are convenient and can be used in practice, the VIKOR method accomplished the tests with the best results and thus can be recommended as the most suitable for simulations of large-scale agent-based models. PMID:27806061

Comparision of the different probability distributions for earthquake hazard assessment in the North Anatolian Fault Zone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yilmaz, Şeyda, E-mail: seydayilmaz@ktu.edu.tr; Bayrak, Erdem, E-mail: erdmbyrk@gmail.com; Bayrak, Yusuf, E-mail: bayrak@ktu.edu.tr

In this study we examined and compared the three different probabilistic distribution methods for determining the best suitable model in probabilistic assessment of earthquake hazards. We analyzed a reliable homogeneous earthquake catalogue between a time period 1900-2015 for magnitude M ≥ 6.0 and estimated the probabilistic seismic hazard in the North Anatolian Fault zone (39°-41° N 30°-40° E) using three distribution methods namely Weibull distribution, Frechet distribution and three-parameter Weibull distribution. The distribution parameters suitability was evaluated Kolmogorov-Smirnov (K-S) goodness-of-fit test. We also compared the estimated cumulative probability and the conditional probabilities of occurrence of earthquakes for different elapsed timemore » using these three distribution methods. We used Easyfit and Matlab software to calculate these distribution parameters and plotted the conditional probability curves. We concluded that the Weibull distribution method was the most suitable than other distribution methods in this region.« less

Comparison of gel column, card, and cartridge techniques for dog erythrocyte antigen 1.1 blood typing

PubMed Central

Seth, Mayank; Jackson, Karen V.; Winzelberg, Sarah; Giger, Urs

2012-01-01

Objective To compare accuracy and ease of use of a card agglutination assay, an immunochromatographic cartridge method, and a gel-based method for canine blood typing. Sample Blood samples from 52 healthy blood donor dogs, 10 dogs with immune-mediated hemolytic anemia (IMHA), and 29 dogs with other diseases. Procedures Blood samples were tested in accordance with manufacturer guidelines. Samples with low PCVs were created by the addition of autologous plasma to separately assess the effects of anemia on test results. Results Compared with a composite reference standard of agreement between 2 methods, the gel-based method was found to be 100% accurate. The card agglutination assay was 89% to 91% accurate, depending on test interpretation, and the immunochromatographic cartridge method was 93% accurate but 100% specific. Errors were observed more frequently in samples from diseased dogs, particularly those with IMHA. In the presence of persistent autoagglutination, dog erythrocyte antigen (DEA) 1.1 typing was not possible, except with the immunochromatographic cartridge method. Conclusions and Clinical Relevance The card agglutination assay and immunochromatographic cartridge method, performed by trained personnel, were suitable for in-clinic emergency DEA 1.1 blood typing. There may be errors, particularly for samples from dogs with IMHA, and the immunochromatographic cartridge method may have an advantage of allowing typing of samples with persistent autoagglutination. The laboratory gel-based method would be preferred for routine DEA 1.1 typing of donors and patients if it is available and time permits. Current DEA 1.1 typing techniques appear to be appropriately standardized and easy to use. PMID:22280380

Mineral resource potential map of the Troublesome Roadless Area, McCreary County, Kentucky

USGS Publications Warehouse

Sigleo, W.R.; Randall, A. H.; Ross, R.B.; Hammack, R.W.

1982-01-01

Possible uses for sandstone units include silica sand, construction sand, and dimension stone. Shale may be suitable for structural clay products. Commercial quantities of oil and gas may be present at shallow depth in rocks of Mississippian age. A stream-sediment geochemical survey failed to recognize anomalies that would suggest mineralization, and the metallic mineral potential of the study area appears limited.

Salts of alkali metal anions and process of preparing same

DOEpatents

Dye, James L.; Ceraso, Joseph M.; Tehan, Frederick J.; Lok, Mei Tak

1978-01-01

Compounds of alkali metal anion salts of alkali metal cations in bicyclic polyoxadiamines are disclosed. The salts are prepared by contacting an excess of alkali metal with an alkali metal dissolving solution consisting of a bicyclic polyoxadiamine in a suitable solvent, and recovered by precipitation. The salts have a gold-color crystalline appearance and are stable in a vacuum at -10.degree. C. and below.

Section V: Conclusions

DTIC Science & Technology

2001-06-01

aeromedical issues. The section concludes with a sample review of a candidate medication, in this case losartan potassium, with a possible approach to...as losartan , Allergic rhinitis is a very common condition appear to hold promise for use in aircrew and generally compatible with military aircrew...evaluating the aeromedical suitability of HI antihistamines for this condition in aircrew losartan led our group to designate losartan as a because of

Miconia biocontrol: Where are we going and when will we get there?

Treesearch

M.T. Johnson

2010-01-01

We have made much progress in evaluating potential agents for biocontrol of miconia, and several appear likely to be suitable for future introduction to Hawaiÿi. Unfortunately, none of them is an obvious silver bullet. We face the challenge of prioritizing the existing candidates and inventing the combination of agents that will achieve our goals. Now is an opportune...

Automated Robust Image Segmentation: Level Set Method Using Nonnegative Matrix Factorization with Application to Brain MRI.

PubMed

Dera, Dimah; Bouaynaya, Nidhal; Fathallah-Shaykh, Hassan M

2016-07-01

We address the problem of fully automated region discovery and robust image segmentation by devising a new deformable model based on the level set method (LSM) and the probabilistic nonnegative matrix factorization (NMF). We describe the use of NMF to calculate the number of distinct regions in the image and to derive the local distribution of the regions, which is incorporated into the energy functional of the LSM. The results demonstrate that our NMF-LSM method is superior to other approaches when applied to synthetic binary and gray-scale images and to clinical magnetic resonance images (MRI) of the human brain with and without a malignant brain tumor, glioblastoma multiforme. In particular, the NMF-LSM method is fully automated, highly accurate, less sensitive to the initial selection of the contour(s) or initial conditions, more robust to noise and model parameters, and able to detect as small distinct regions as desired. These advantages stem from the fact that the proposed method relies on histogram information instead of intensity values and does not introduce nuisance model parameters. These properties provide a general approach for automated robust region discovery and segmentation in heterogeneous images. Compared with the retrospective radiological diagnoses of two patients with non-enhancing grade 2 and 3 oligodendroglioma, the NMF-LSM detects earlier progression times and appears suitable for monitoring tumor response. The NMF-LSM method fills an important need of automated segmentation of clinical MRI.

Artificial intelligence in predicting bladder cancer outcome: a comparison of neuro-fuzzy modeling and artificial neural networks.

PubMed

Catto, James W F; Linkens, Derek A; Abbod, Maysam F; Chen, Minyou; Burton, Julian L; Feeley, Kenneth M; Hamdy, Freddie C

2003-09-15

New techniques for the prediction of tumor behavior are needed, because statistical analysis has a poor accuracy and is not applicable to the individual. Artificial intelligence (AI) may provide these suitable methods. Whereas artificial neural networks (ANN), the best-studied form of AI, have been used successfully, its hidden networks remain an obstacle to its acceptance. Neuro-fuzzy modeling (NFM), another AI method, has a transparent functional layer and is without many of the drawbacks of ANN. We have compared the predictive accuracies of NFM, ANN, and traditional statistical methods, for the behavior of bladder cancer. Experimental molecular biomarkers, including p53 and the mismatch repair proteins, and conventional clinicopathological data were studied in a cohort of 109 patients with bladder cancer. For all three of the methods, models were produced to predict the presence and timing of a tumor relapse. Both methods of AI predicted relapse with an accuracy ranging from 88% to 95%. This was superior to statistical methods (71-77%; P < 0.0006). NFM appeared better than ANN at predicting the timing of relapse (P = 0.073). The use of AI can accurately predict cancer behavior. NFM has a similar or superior predictive accuracy to ANN. However, unlike the impenetrable "black-box" of a neural network, the rules of NFM are transparent, enabling validation from clinical knowledge and the manipulation of input variables to allow exploratory predictions. This technique could be used widely in a variety of areas of medicine.

Three methods for isolating viable anthozoan endoderm cells with their intracellular symbiotic dinoflagellates

NASA Astrophysics Data System (ADS)

Gates, R. D.; Muscatine, L.

1992-09-01

Three maceration methods are described for the isolation of single endoderm cells from marine cnidarians. Two are enzymatic treatments suitable for fleshy anthozoans such as sea anemones and zoanthids. The third employs calcium free sea water and is suitable for stony corals. The viability and morphology of the endoderm cells is described using fluorogenic dyes and scanning and transmission electron microscopy.

3D Molding of Veneers by Mechanical and Pneumatic Methods

PubMed Central

Gaff, Milan; Gašparík, Miroslav

2017-01-01

This paper deals with the influence of selected methods (mechanical and pneumatic) as well as various factors (wood species, moisture content, veneer shape, punch diameter, laminating foil thickness, holding method, plasticizing) on 3D molding of veneers. 3D molding was evaluated on the basis of maximum deflection of birch and beech veneers. Cracks and warping edges were also evaluated in selected groups of mechanical molding. Mechanical methods tested veneers with various treatments (steaming, water and ammonia plasticizing and lamination). The pneumatic method was based on veneer shaping using air pressure. The results indicate that birch veneers are more suitable for 3D molding. The differences between the mechanical and pneumatic methods were not considerable. The most suitable method for mechanical 3D molding was the veneer lamination by polyethylene foils with thicknesses of 80 and 125 μm, inasmuch as these achieved better results than veneer plasticized by steam. The occurrence of cracks was more frequent in beech veneers, whereas, edge warping occurred at similar rates for both wood species and depends rather on holding method during 3D molding. Use of the ammonia solution is more suitable and there occurs no marked increase in moisture as happens when soaking in water. PMID:28772684

The quantitative modelling of human spatial habitability

NASA Technical Reports Server (NTRS)

Wise, J. A.

1985-01-01

A model for the quantitative assessment of human spatial habitability is presented in the space station context. The visual aspect assesses how interior spaces appear to the inhabitants. This aspect concerns criteria such as sensed spaciousness and the affective (emotional) connotations of settings' appearances. The kinesthetic aspect evaluates the available space in terms of its suitability to accommodate human movement patterns, as well as the postural and anthrometric changes due to microgravity. Finally, social logic concerns how the volume and geometry of available space either affirms or contravenes established social and organizational expectations for spatial arrangements. Here, the criteria include privacy, status, social power, and proxemics (the uses of space as a medium of social communication).

Release of indomethacin from ultrasound dry granules containing lactose-based excipients.

PubMed

Cavallari, Cristina; Albertini, Beatrice; Rodriguez, Lorenzo; Rabasco, Antonio M; Fini, Adamo

2005-01-20

Physical mixtures were prepared containing indomethacin and beta-lactose and alpha-lactose-based excipients (Ludipress and Cellactose). The mixtures were compacted with the aid of ultrasound, obtaining tablets, which were milled and sieved. Granules thus obtained were examined by optical microscopy and differential scanning calorimetry. The intense yellow color of the granules and the absence of indomethacin peak in thermograms suggest important modifications of indomethacin physical state; the drug thus modified appears to be spread on the excipient particle surface as a thin film, giving a lustrous appearance. No influence of ultrasound was observed on phase transition concerning lactose; only loss of water was important under high energy ultrasound. Dissolution profiles suggest an increased release of the drug from the systems treated with ultrasound at high energy, with respect to a traditional compaction; while no difference could be evidenced among the three excipients that, however, appear all suitable for this ultrasound-aided direct compression process.

Land suitability assessment for wind power plant site selection using ANP-DEMATEL in a GIS environment: case study of Ardabil province, Iran.

PubMed

Azizi, Ali; Malekmohammadi, Bahram; Jafari, Hamid Reza; Nasiri, Hossein; Amini Parsa, Vahid

2014-10-01

Wind energy is a renewable energy resource that has increased in usage in most countries. Site selection for the establishment of large wind turbines, called wind farms, like any other engineering project, requires basic information and careful planning. This study assessed the possibility of establishing wind farms in Ardabil province in northwestern Iran by using a combination of analytic network process (ANP) and decision making trial and evaluation laboratory (DEMATEL) methods in a geographical information system (GIS) environment. DEMATEL was used to determine the criteria relationships. The weights of the criteria were determined using ANP and the overlaying process was done on GIS. Using 13 information layers in three main criteria including environmental, technical and economical, the land suitability map was produced and reclassified into 5 equally scored divisions from least suitable to most suitable areas. The results showed that about 6.68% of the area of Ardabil province is most suitable for establishment of wind turbines. Sensitivity analysis shows that significant portions of these most suitable zones coincide with suitable divisions of the input layers. The efficiency and accuracy of the hybrid model (ANP-DEMATEL) was evaluated and the results were compared to the ANP model. The sensitivity analysis, map classification, and factor weights for the two methods showed satisfactory results for the ANP-DEMATEL model in wind power plant site selection.

Regional prediction of basin-scale brown trout habitat suitability

NASA Astrophysics Data System (ADS)

Ceola, S.; Pugliese, A.

2014-09-01

In this study we propose a novel method for the estimation of ecological indices describing the habitat suitability of brown trout (Salmo trutta). Traditional hydrological tools are coupled with an innovative regional geostatistical technique, aiming at the prediction of the brown trout habitat suitability index where partial or totally ungauged conditions occur. Several methods for the assessment of ecological indices are already proposed in the scientific literature, but the possibility of exploiting a geostatistical prediction model, such as Topological Kriging, has never been investigated before. In order to develop a regional habitat suitability model we use the habitat suitability curve, obtained from measured data of brown trout adult individuals collected in several river basins across the USA. The Top-kriging prediction model is then employed to assess the spatial correlation between upstream and downstream habitat suitability indices. The study area is the Metauro River basin, located in the central part of Italy (Marche region), for which both water depth and streamflow data were collected. The present analysis focuses on discharge values corresponding to the 0.1-, 0.5-, 0.9-empirical quantiles derived from flow-duration curves available for seven gauging stations located within the study area, for which three different suitability indices (i.e. ψ10, ψ50 and ψ90) are evaluated. The results of this preliminary analysis are encouraging showing Nash-Sutcliffe efficiencies equal to 0.52, 0.65, and 0.69, respectively.

The Use of Color Sensors for Spectrographic Calibration

NASA Astrophysics Data System (ADS)

Thomas, Neil B.

2018-04-01

The wavelength calibration of spectrographs is an essential but challenging task in many disciplines. Calibration is traditionally accomplished by imaging the spectrum of a light source containing features that are known to appear at certain wavelengths and mapping them to their location on the sensor. This is typically required in conjunction with each scientific observation to account for mechanical and optical variations of the instrument over time, which may span years for certain projects. The method presented here investigates the usage of color itself instead of spectral features to calibrate a spectrograph. The primary advantage of such a calibration is that any broad-spectrum light source such as the sky or an incandescent bulb is suitable. This method allows for calibration using the full optical pathway of the instrument instead of incorporating separate calibration equipment that may introduce errors. This paper focuses on the potential for color calibration in the field of radial velocity astronomy, in which instruments must be finely calibrated for long periods of time to detect tiny Doppler wavelength shifts. This method is not restricted to radial velocity, however, and may find application in any field requiring calibrated spectrometers such as sea water analysis, cellular biology, chemistry, atmospheric studies, and so on. This paper demonstrates that color sensors have the potential to provide calibration with greatly reduced complexity.

Methods of Ex Situ and In Situ Investigations of Structural Transformations: The Case of Crystallization of Metallic Glasses.

PubMed

Miglierini, Marcel B; Procházka, Vít; Vrba, Vlastimil; Švec, Peter; Janičkovič, Dušan; Matúš, Peter

2018-06-07

We demonstrate the use of two nuclear-based analytical methods that can follow the modifications of microstructural arrangement of iron-based metallic glasses (MGs). Despite their amorphous nature, the identification of hyperfine interactions unveils faint structural modifications. For this purpose, we have employed two techniques that utilize nuclear resonance among nuclear levels of a stable 57 Fe isotope, namely Mössbauer spectrometry and nuclear forward scattering (NFS) of synchrotron radiation. The effects of heat treatment upon (Fe2.85Co1)77Mo8Cu1B14 MG are discussed using the results of ex situ and in situ experiments, respectively. As both methods are sensitive to hyperfine interactions, information on structural arrangement as well as on magnetic microstructure is readily available. Mössbauer spectrometry performed ex situ describes how the structural arrangement and magnetic microstructure appears at room temperature after the annealing under certain conditions (temperature, time), and thus this technique inspects steady states. On the other hand, NFS data are recorded in situ during dynamically changing temperature and NFS examines transient states. The use of both techniques provides complementary information. In general, they can be applied to any suitable system in which it is important to know its steady state but also transient states.

Multimodal Sensing Strategy Using pH Dependent Fluorescence Switchable System

NASA Astrophysics Data System (ADS)

Muthurasu, A.; Ganesh, V.

2016-12-01

Biomolecules assisted preparation of fluorescent gold nanoparticles (FL-Au NPs) has been reported in this work using glucose oxidase enzyme as both reducing and stabilizing agent and demonstrated their application through multimodal sensing strategy for selective detection of cysteine (Cys). Three different methods namely fluorescence turn OFF-ON strategy, naked eye detection and electrochemical methods are used for Cys detection by employing FL-Au NPs as a common probe. In case of fluorescence turn-OFF method a strong interaction between Au NPs and thiol results in quenching of fluorescence due to replacement of glucose oxidase by Cys at neutral pH. Second mode is based on fluorescence switch-ON strategy where initial fluorescence is significantly quenched by either excess acid or base and further addition of Cys results in appearance of rosy-red and green fluorescence respectively. Visual colour change and fluorescence emission arises due to etching of Au atoms on the surface by thiol leading to formation of Au nanoclusters. Finally, electrochemical sensing of Cys is also carried out using cyclic voltammetry in 0.1 M PBS solution. These findings provide a suitable platform for Cys detection over a wide range of pH and concentration levels and hence the sensitivity can also be tuned accordingly.

Fine-grained recognition of plants from images.

PubMed

Šulc, Milan; Matas, Jiří

2017-01-01

Fine-grained recognition of plants from images is a challenging computer vision task, due to the diverse appearance and complex structure of plants, high intra-class variability and small inter-class differences. We review the state-of-the-art and discuss plant recognition tasks, from identification of plants from specific plant organs to general plant recognition "in the wild". We propose texture analysis and deep learning methods for different plant recognition tasks. The methods are evaluated and compared them to the state-of-the-art. Texture analysis is only applied to images with unambiguous segmentation (bark and leaf recognition), whereas CNNs are only applied when sufficiently large datasets are available. The results provide an insight in the complexity of different plant recognition tasks. The proposed methods outperform the state-of-the-art in leaf and bark classification and achieve very competitive results in plant recognition "in the wild". The results suggest that recognition of segmented leaves is practically a solved problem, when high volumes of training data are available. The generality and higher capacity of state-of-the-art CNNs makes them suitable for plant recognition "in the wild" where the views on plant organs or plants vary significantly and the difficulty is increased by occlusions and background clutter.

Protein Crystal Growth With the Aid of Microfluidics

NASA Technical Reports Server (NTRS)

vanderWoerd, Mark

2003-01-01

Protein crystallography is one of three well-known methods to obtain the structure of proteins. A major rate limiting step in protein crystallography is protein crystal nucleation and growth, which is still largely a process conducted by trial-and-error methods. Many attempts have been made to improve protein crystal growth by performing growth in microgravity. Although the use of microgravity appears to improve crystal quality in some attempts, this method has been inefficient because several reasons: we lack a fundamental understanding of macromolecular crystal growth in general and of the influence of microgravity in particular, we have to start with crystal growth conditions in microgravity based on conditions on the ground and finally the hardware does not allow for experimental iteration without reloading samples on the ground. To partially accommodate the disadvantages of the current hardware, we have used microfluidic technology (Lab-on-a-Chip devices) to design the concept of a more efficient crystallization device, suitable for use on the International Space Station and in high-throughput applications on the ground. The concept and properties of microfluidics, the application design process, and the advances in protein crystal growth hardware will be discussed in this presentation. Some examples of proteins crystallized in the new hardware will be discussed, including the differences between conventional crystallization versus crystallization in microfluidics.

Microbial community, and biochemical and physiological properties of Korean traditional black raspberry (Robus coreanus Miquel) vinegar.

PubMed

Song, Nho-Eul; Cho, Sung-Ho; Baik, Sang-Ho

2016-08-01

The aim of this study was to elucidate the changes in microbial community and biochemical and physiological properties of traditional Muju black raspberry (Robus coreanus Miquel) vinegar (TMBV) during fermentation by culture-independent methods. During vinegar fermentation, ethanol produced up to 120 g L(-1) until day 35, with continuously increasing yeast concentration to a total of log 7.6 CFU mL(-1) . After day 35, acetic acid bacteria (AAB) concentrations rose to log 5.8 CFU mL(-1) until day 144. Denaturing gradient gel electrophoresis analysis showed that Saccharomyces cerevisiae was detected until day 87 of the fermentation, at which point Acetobacter pasteurianus gradually took over as the dominant species. Total sugar was reduced to 6.6 °Brix and total acidity produced up to 44 g L(-1) . In this study, we established the physicochemical analysis and growth dynamics of yeast and AAB during alcoholic and acetic acid fermentation of black raspberry by a traditional method. Overall, S. cerevisiae and A. pasteurianus species appeared to dominate the TMBV fermentation. In conclusion, this study demonstrated a suitable fermentation system for TMBV by the static surface method. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

BlastNeuron for Automated Comparison, Retrieval and Clustering of 3D Neuron Morphologies.

PubMed

Wan, Yinan; Long, Fuhui; Qu, Lei; Xiao, Hang; Hawrylycz, Michael; Myers, Eugene W; Peng, Hanchuan

2015-10-01

Characterizing the identity and types of neurons in the brain, as well as their associated function, requires a means of quantifying and comparing 3D neuron morphology. Presently, neuron comparison methods are based on statistics from neuronal morphology such as size and number of branches, which are not fully suitable for detecting local similarities and differences in the detailed structure. We developed BlastNeuron to compare neurons in terms of their global appearance, detailed arborization patterns, and topological similarity. BlastNeuron first compares and clusters 3D neuron reconstructions based on global morphology features and moment invariants, independent of their orientations, sizes, level of reconstruction and other variations. Subsequently, BlastNeuron performs local alignment between any pair of retrieved neurons via a tree-topology driven dynamic programming method. A 3D correspondence map can thus be generated at the resolution of single reconstruction nodes. We applied BlastNeuron to three datasets: (1) 10,000+ neuron reconstructions from a public morphology database, (2) 681 newly and manually reconstructed neurons, and (3) neurons reconstructions produced using several independent reconstruction methods. Our approach was able to accurately and efficiently retrieve morphologically and functionally similar neuron structures from large morphology database, identify the local common structures, and find clusters of neurons that share similarities in both morphology and molecular profiles.

Water Walls for Life Support

NASA Technical Reports Server (NTRS)

Hammoudeh, Mona (Inventor); Flynn, Michael T. (Inventor); Gormly, Sherwin J. (Inventor); Richardson, Tra-My Justine (Inventor)

2017-01-01

A method and associated system for processing waste gases, liquids and solids, produced by human activity, to separate (i) liquids suitable for processing to produce potable water, (ii) solids and liquids suitable for construction of walls suitable for enclosing a habitat volume and for radiation shielding, and (iii) other fluids and solids that are not suitable for processing. A forward osmosis process and a reverse osmosis process are sequentially combined to reduce fouling and to permit accumulation of different processable substances. The invention may be used for long term life support of human activity.

Gis-Based Solar and Wind Turbine Site Selection Using Multi-Criteria Analysis: Case Study Tehran, Iran

NASA Astrophysics Data System (ADS)

Sadeghi, M.; Karimi, M.

2017-09-01

Renewable energy has less negative impacts on environment than fossil fuels. Iran has many resources for renewable energy exploitation but because of their high price, it has not been developed. Site selection is an important step for utilizing large investments like solar farms and wind turbines. Multi-criteria evaluation methods are commonly used for site selection. The purpose of this paper is to determine suitable sites for solar farm and wind turbine using GIS and AHP in Tehran, in order to generate a distributed network to increase power network stability. The final land suitability index was grouped in four categories as "most suitable", "suitable", "moderate" and "low suitable". As a result 94.61% (789939.63 km2) is low suitable, 4.47% (37337.17 km2) is moderate, 0.59% (4964.22 km2) is suitable and 0.32% (2680.70 km2) is the most suitable for building wind turbine and for solar farm, 44.07% (8116.88 km2) is low suitable, 12.81% (2359.79 km2) is moderate, 35.10% (6464.29 km2) is suitable and 8.02% (1477.28 km2) is the most suitable.

International travel between global urban centres vulnerable to yellow fever transmission.

PubMed

Brent, Shannon E; Watts, Alexander; Cetron, Martin; German, Matthew; Kraemer, Moritz Ug; Bogoch, Isaac I; Brady, Oliver J; Hay, Simon I; Creatore, Maria I; Khan, Kamran

2018-05-01

To examine the potential for international travel to spread yellow fever virus to cities around the world. We obtained data on the international flight itineraries of travellers who departed yellow fever-endemic areas of the world in 2016 for cities either where yellow fever was endemic or which were suitable for viral transmission. Using a global ecological model of dengue virus transmission, we predicted the suitability of cities in non-endemic areas for yellow fever transmission. We obtained information on national entry requirements for yellow fever vaccination at travellers' destination cities. In 2016, 45.2 million international air travellers departed from yellow fever-endemic areas of the world. Of 11.7 million travellers with destinations in 472 cities where yellow fever was not endemic but which were suitable for virus transmission, 7.7 million (65.7%) were not required to provide proof of vaccination upon arrival. Brazil, China, India, Mexico, Peru and the United States of America had the highest volumes of travellers arriving from yellow fever-endemic areas and the largest populations living in cities suitable for yellow fever transmission. Each year millions of travellers depart from yellow fever-endemic areas of the world for cities in non-endemic areas that appear suitable for viral transmission without having to provide proof of vaccination. Rapid global changes in human mobility and urbanization make it vital for countries to re-examine their vaccination policies and practices to prevent urban yellow fever epidemics.

Macroscopic and microscopic evaluation of a new implant design supporting immediately loaded full arch rehabilitation

PubMed Central

Tetè, Stefano; Zizzari, Vincenzo; De Carlo, Alessandro; Sinjari, Bruna; Gherlone, Enrico

2012-01-01

Summary The purpose of this study is to evaluate macroscopic and microscopic appearance of a new implant design, with particular emphasis given to the type of prosthesis connection. Two dental implants of the same type (Torque Type®, WinSix®, BioSAFin. S.r.l. - Ancona, Italy), with sandblasted and acid etched surfaces (Micro Rough Surface®), but differing from each other for the prosthesis connection system, were examined by scanning electron microscope (SEM) analysis at different magnifications: TTI implant, with a hexagonal internal connection, and TTX implant, with a hexagonal external connection. SEM analysis showed that the Torque Type® implant is characterized by a truncated cone shape with tapered tips. The implant body showed a double loop thread and double pitch with blunt tips. For both types of connection, the implant neck was 0.7 mm in height with a 3% taper. This implant design may be able to guarantee osteotomic properties at the time of insertion in a surgical site suitably prepared, a facilitated screwing, thanks to the thread pitch and to the broad and deep draining grooves, thereby ensuring a good primary stability. The different connection design appears defined and precise, in order to ensure a good interface between the fixture and the prosthetic components. Therefore, this design appears to be particularly suitable in cases where a good primary stability is necessary and a precise coupling between endosseous and prosthetic components, as it allows an easy insertion of the fixture even in conditions of reduced bone availability, and in cases of immediately loaded full-arch rehabilitations. PMID:23087785

Macroscopic and microscopic evaluation of a new implant design supporting immediately loaded full arch rehabilitation.

PubMed

Tetè, Stefano; Zizzari, Vincenzo; De Carlo, Alessandro; Sinjari, Bruna; Gherlone, Enrico

2012-04-01

The purpose of this study is to evaluate macroscopic and microscopic appearance of a new implant design, with particular emphasis given to the type of prosthesis connection. Two dental implants of the same type (Torque Type(®), WinSix(®), BioSAFin. S.r.l. - Ancona, Italy), with sandblasted and acid etched surfaces (Micro Rough Surface(®)), but differing from each other for the prosthesis connection system, were examined by scanning electron microscope (SEM) analysis at different magnifications: TTI implant, with a hexagonal internal connection, and TTX implant, with a hexagonal external connection. SEM analysis showed that the Torque Type(®) implant is characterized by a truncated cone shape with tapered tips. The implant body showed a double loop thread and double pitch with blunt tips. For both types of connection, the implant neck was 0.7 mm in height with a 3% taper. This implant design may be able to guarantee osteotomic properties at the time of insertion in a surgical site suitably prepared, a facilitated screwing, thanks to the thread pitch and to the broad and deep draining grooves, thereby ensuring a good primary stability. The different connection design appears defined and precise, in order to ensure a good interface between the fixture and the prosthetic components. Therefore, this design appears to be particularly suitable in cases where a good primary stability is necessary and a precise coupling between endosseous and prosthetic components, as it allows an easy insertion of the fixture even in conditions of reduced bone availability, and in cases of immediately loaded full-arch rehabilitations.

Actual light deflections in regions of crack tips and their influence on measurements in photomechanics

NASA Astrophysics Data System (ADS)

Hecker, Friedrich W.; Pindera, Jerzy T.; Wen, Baicheng

Crack-tip photomechanics procedures are based on certain simplifying assumptions that are seldom discussed. In a recent paper the theoretical bases of the shadow optical methods of caustics have been analysed and tested using the results obtained by three analytical-experimental procedures, namely classical strain gage techniques, isodynes, and strain-gradient index method. It has been concluded that the straing-radient index method appears to be a suitable tool for analysis of stress states near crack tips and notches and, in particular, for testing the predictive power of the pertinent singular solutions of the linear elastic fracture mechanics and the ranges of their applicability. In the present paper, a more detailed analysis of all results obtained in light deflection experiments allows to quantify the contribution of both involved effects and to determine the distortion of the faces of the investigated plates along their crack planes. The ability of the strain-gradient light bending method to analyse some features of the three-dimensional stress-state is reported. Finally, the presented experimental evidence allows to draw conclusions related to limits of applicability of certain photomechanical measurements near crack tips. An extensive summary of this paper is published in the Proceedings of the Second International Conference on Photomechanics and Speckle Metrology, Vol. 1554A, part of SPIE's 1991 International Symposium on Optical Applied Science and Engineering, 22-26 July 1991, San Diego, CA, USA. 1

Dried blood spot assay for the quantification of phenytoin using Liquid Chromatography-Mass Spectrometry.

PubMed

Villanelli, Fabio; Giocaliere, Elisa; Malvagia, Sabrina; Rosati, Anna; Forni, Giulia; Funghini, Silvia; Shokry, Engy; Ombrone, Daniela; Della Bona, Maria Luisa; Guerrini, Renzo; la Marca, Giancarlo

2015-02-02

Phenytoin (PHT) is one of the most commonly used anticonvulsant drugs for the treatment of epilepsy and bipolar disorders. The large amount of plasma required by conventional methods for drug quantification makes mass spectrometry combined with dried blood spot (DBS) sampling crucial for pediatric patients where therapeutic drug monitoring or pharmacokinetic studies may be difficult to realize. DBS represents a new convenient sampling support requiring minimally invasive blood drawing and providing long-term stability of samples and less expensive shipment and storage. The aim of this study was to develop a LC-MS/MS method for the quantification of PHT on DBS. This analytical method was validated and gave good linearity (r(2)=0.999) in the range of 0-100mg/l. LOQ and LOD were 1.0mg/l and 0.3mg/l, respectively. The drug extraction from paper was performed in a few minutes using a mixture composed of organic solvent for 80%. The recovery ranged from 85 to 90%; PHT in DBS showed to be stable at different storage temperatures for one month. A good correlation was also obtained between PHT plasma and DBS concentrations. This method is both precise and accurate and appears to be particularly suitable to monitor treatment with a simple and convenient sample collection procedure. Copyright © 2014 Elsevier B.V. All rights reserved.

Toward a suitable structural analysis of gene delivery carrier based on polycationic carbohydrates by electron transfer dissociation tandem mass spectrometry.

PubMed

Przybylski, Cédric; Benito, Juan M; Bonnet, Véronique; Mellet, Carmen Ortiz; García Fernández, José M

2016-12-15

Polycationic carbohydrates represent an attractive class of biomolecules for several applications and particularly as non viral gene delivery vectors. In this case, the establishment of structure-biological activity relationship requires sensitive and accurate characterization tools to both control and achieve fine structural deciphering. Electrospray-tandem mass spectrometry (ESI-MS/MS) appears as a suitable approach to address these questions. In the study herein, we have investigated the usefulness of electron transfer dissociation (ETD) to get structural data about five polycationic carbohydrates demonstrated as promising gene delivery agents. A particular attention was paid to determine the influence of charge states as well as both fluoranthene reaction time and supplementary activation (SA) on production of charge reduced species, fragmentation yield, varying from 2 to 62%, as well as to obtain the most higher both diversity and intensity of fragments, according to charge states and targeted compounds. ETD fragmentation appeared to be mainly directed toward pending group rather than carbohydrate cyclic scaffold leading to a partial sequencing for building blocks when amino groups are close to carbohydrate core, but allowing to complete structural deciphering of some of them, such as those including dithioureidocysteaminyl group which was not possible with CID only. Such findings clearly highlight the potential to help the rational choice of the suitable analytical conditions, according to the nature of the gene delivery molecules exhibiting polycationic features. Moreover, our ETD-MS/MS approach open the way to a fine sequencing/identification of grafted groups carried on various sets of oligo-/polysaccharides in various fields such as glycobiology or nanomaterials, even with unknown or questionable extraction, synthesis or modification steps. Copyright © 2016 Elsevier B.V. All rights reserved.

Development of a new clot formation protocol for standardized in vitro investigations of sonothrombolysis.

PubMed

Roessler, Florian C; Teichert, Andrea; Ohlrich, Marcus; Marxsen, Jan H; Stellmacher, Florian; Tanislav, Christian; Seidel, Günter

2014-11-30

Agreement about the most suitable clot formation protocol for sonothrombolysis investigations is lacking. Lysis rates vary strongly owing to different test conditions and, thus, cannot be compared. We aim to establish a simple but physiologically grounded protocol for in vitro coagulation to enable standardized sonothrombolysis investigations. Clots were generated from platelet-rich plasma (PRP) obtained by centrifugation (10 min, 180 × g) of human venous blood (VB). PRP was mixed with the boundary layer formed between the supernatant and the erythrocyte layer. To achieve clots with different platelet counts, PRP was gradually substituted with platelet-free plasma (PFP), harvested from the supernatant of VB after centrifugation (10 min, 2570 × g). Clot types were examined for histological appearance, hydrodynamic resistance under physiological flows, and lysis rate measured by weight loss after a 2-h treatment with recombinant tissue plasminogen activator (rt-PA) (60 kU/ml). Lysis rates of the most suitable clot were measured after a 1-h treatment with rt-PA (60 kU/ml), and combined treatment with rt-PA and 2-MHz transcranial color-coded sonography (TCCS) (0.179 W/cm(2)) or 2-MHz transcranial Doppler (TCD) (0.457 W/cm(2)). With increased platelet count, the hydrodynamic resistance of the artificial clots increased, their histological appearance became more physiological, and lysis rates decreased. The most suitable clots consisted of 1.5-ml PRP, 2.0-ml PFP, and 0.5-ml boundary layer. Their lysis rates were 36.7 ± 7.8% (rt-PA), 40.8 ± 8.6% (rt-PA+TCCS), and 40.4 ± 8.3% (rt-PA+TCD). These systemic investigations were conducted for the first time. This protocol should be used for standardized sonothrombolysis investigations. Copyright © 2014 Elsevier B.V. All rights reserved.

An iterative method for near-field Fresnel region polychromatic phase contrast imaging

NASA Astrophysics Data System (ADS)

Carroll, Aidan J.; van Riessen, Grant A.; Balaur, Eugeniu; Dolbnya, Igor P.; Tran, Giang N.; Peele, Andrew G.

2017-07-01

We present an iterative method for polychromatic phase contrast imaging that is suitable for broadband illumination and which allows for the quantitative determination of the thickness of an object given the refractive index of the sample material. Experimental and simulation results suggest the iterative method provides comparable image quality and quantitative object thickness determination when compared to the analytical polychromatic transport of intensity and contrast transfer function methods. The ability of the iterative method to work over a wider range of experimental conditions means the iterative method is a suitable candidate for use with polychromatic illumination and may deliver more utility for laboratory-based x-ray sources, which typically have a broad spectrum.

Satellite sound broadcasting system study: Mobile considerations

NASA Technical Reports Server (NTRS)

Golshan, Nasser

1990-01-01

Discussed here is the mobile reception part of a study to investigate a satellite sound broadcast system in the UHF or L bands. Existing propagation and reception measurements are used with proper interpretation to evaluate the signaling, coding, and diversity alternatives suitable for the system. Signal attenuation in streets shadowed by buildings appear to be around 29 db, considerably higher than the 10 db adopted by CCIR. With the marriage of proper technologies, an LMSS class satellite can provide substantial direct satellite audio broadcast capability in UHF or L bands for high quality mobile and portable indoor reception by low cost radio receivers. This scheme requires terrestrial repeaters for satisfactory mobile reception in urban areas. A specialized bandwidth efficient spread spectrum signalling technique is particularly suitable for the terrestrial repeaters.

Predicting suitable habitat for the gold coral Savalia savaglia (Bertoloni, 1819) (Cnidaria, Zoantharia) in the South Tyrrhenian Sea

NASA Astrophysics Data System (ADS)

Giusti, Michela; Innocenti, Carlo; Canese, Simonepietro

2014-06-01

The gold coral Savalia savaglia (Cnidaria, Zoantharia) is a rare component of the mesophotic zone of the Mediterranean Sea and northeastern Atlantic Ocean. During two field campaigns along the Italian coast in the South Tyrrhenian Sea, two populations of this species were discovered. The specimens were filmed and photographed by means of a Remotely Operated Vehicle (ROV). To identify the role of local bathymetry and other derived variables on presence and distribution of S. savaglia we used a Habitat Suitability (HS) modeling technique based on Ecological Niche Factor Analysis (ENFA), utilizing high-resolution multibeam bathymetry and ROV data. Among the set of environmental variables derived from multibeam data, slope, rugosity, eastness and distance to rocks, appear to be the main variables involved in S. savaglia distribution, pointing out that the habitat differs considerably from the mean environmental conditions over the study area, and that S. savaglia ecological niche is significantly narrower than the available habitat. The HS map was developed to differentiate the sea floor into suitability classes. The comparison between suitability classes and presence data showed that the HS map is coherent with the observed spatial distribution of the species. The most suitable habitat for S. savaglia is characterized by a rough sea floor with rocks that is steeply sloped, oriented northeast, and within a water depth range of 34-77 m. Our study suggests that predictive modeling is an approach that can be applied to other deep coral species to locate areas with a suitable habitat. Considering the difficulties to reach the habitats in which these species live, this approach could be essential to planning further studies that help define areas where the species may be present.

A New Method for Unconstrained Heart Rate Monitoring

DTIC Science & Technology

2001-10-25

members. However, care of bedridden elderly persons are not easy task, and this caused severe psychological and financial problems for other family...physical and mental conditions of bedridden elderly people at home and patients at hospitals and to contribute to the labor saving of the care and the...not suitable for home care of bedridden elderly people. Our method provides very small, simple and mechanically rugged device suitable for home

The source and impact of appearance teasing: an examination by sex and weight status among early adolescents from the Czech Republic.

PubMed

Almenara, Carlos A; Ježek, Stanislav

2015-03-01

Some adolescents are victims of negative appearance-related feedback, and this may have lasting adverse effects on their self-evaluation. The aim of this study was to examine the frequency and impact of appearance teasing across sex and weight status. The participants were 570 Czech adolescents (47.9% girls) evaluated at age 13 during the European Longitudinal Study of Pregnancy and Childhood. Instruments used were body mass index and an adapted version of the Physical Experiences Survey that measures appearance teasing sources (parents, peers, among others), body part teased, and the impact of teasing. Chi-square test and multivariate analyses of variance were conducted to compare groups by sex and weight status. Logistic regression was then used for adjusted analyses. Girls were more likely to report appearance teasing than boys. Overweight adolescents, both girls and boys, were more likely to be teased than non-overweight adolescents. Overweight adolescents compared with non-overweight adolescents reported higher levels of impact of body-related teasing. Czech adolescents continue to adopt the societal standards of Western countries, stigmatizing overweight peers. This may affect more obese adolescents. Future research has to evaluate different sources of appearance-related teasing. Interventions in schools are suitable for the reduction of appearance-related prejudices. © 2015, American School Health Association.

A rapid method for the extraction and analysis of carotenoids and other hydrophobic substances suitable for systems biology studies with photosynthetic bacteria.

PubMed

Bóna-Lovász, Judit; Bóna, Aron; Ederer, Michael; Sawodny, Oliver; Ghosh, Robin

2013-10-11

A simple, rapid, and inexpensive extraction method for carotenoids and other non-polar compounds present in phototrophic bacteria has been developed. The method, which has been extensively tested on the phototrophic purple non-sulphur bacterium Rhodospirillum rubrum, is suitable for extracting large numbers of samples, which is common in systems biology studies, and yields material suitable for subsequent analysis using HPLC and mass spectroscopy. The procedure is particularly suitable for carotenoids and other terpenoids, including quinones, bacteriochlorophyll a and bacteriopheophytin a, and is also useful for the analysis of polar phospholipids. The extraction procedure requires only a single step extraction with a hexane/methanol/water mixture, followed by HPLC using a Spherisorb C18 column, with a mobile phase consisting of acetone-water and a non-linear gradient of 50%-100% acetone. The method was employed for examining the carotenoid composition observed during microaerophilic growth of R. rubrum strains, and was able to determine 18 carotenoids, 4 isoprenoid-quinones, bacteriochlorophyll a and bacteriopheophytin a as well as four different phosphatidylglycerol species of different acyl chain compositions. The analytical procedure was used to examine the dynamics of carotenoid biosynthesis in the major and minor pathways operating simultaneously in a carotenoid biosynthesis mutant of R. rubrum.

Site suitability evaluation of an old operating landfill using AHP and GIS techniques and integrated hydrogeological and geophysical surveys.

PubMed

Saatsaz, Masoud; Monsef, Iman; Rahmani, Mostafa; Ghods, Abdolreza

2018-02-16

Because of the outdated methods of common landfill selection, it is imperative to reevaluate the usage suitability. To assess the suitability of the existing waste landfill in Zanjan, Iran, we have used a combination of the analytical hierarchy process (AHP) and GIS techniques, along with fieldwork surveys. Four major criteria and 12 subcriteria were considered, and the AHP was applied to assign the relative importance weights of criteria and subcriteria to each other. Finally, a landfill suitability map was generated and ranked based on the final suitability scores. The results show that the unsuitable areas are around Zanjan, in the middle parts of the plain. By contrast, the most suitable areas are uncultivated areas, located mostly in the west, north, and south. The results also indicate that the present landfill is a highly suitable site. After desk studies, geoelectrical surveys and infiltration measurements were conducted to make the final decision. Double-ring permeability tests confirm the landfill is an acceptable site. The electrical sounding shows that the leachate plume has a width of about ~ 450 m, spreads to a depth of about ~ 55 m, and migrates towards the northeast. Considering the groundwater depth, dry climate, and a low infiltration rate of the landfill soils, it can be concluded that leachate plumes will not contaminate groundwater within this decade. The proposed method can be implemented to reevaluate the suitability of any old operating reservoir such as oil reservoirs, petrol filling stations, heavy industrial tanks, and landfills, containing liquid hazardous materials.

Discreet passive explosive detection through 2-sided waveguided fluorescence

DOEpatents

Harper, Ross James [Stillwater, OK; la Grone, Marcus [Cushing, OK; Fisher, Mark [Stillwater, OK

2011-10-18

The current invention provides a passive sampling device suitable for collecting and detecting the presence of target analytes. In particular, the passive sampling device is suitable for detecting nitro-aromatic compounds. The current invention further provides a passive sampling device reader suitable for determining the collection of target analytes. Additionally, the current invention provides methods for detecting target analytes using the passive sampling device and the passive sampling device reader.

RADIATION DOSIMETER AND DOSIMETRIC METHODS

DOEpatents

Taplin, G.V.

1958-10-28

The determination of ionizing radiation by means of single fluid phase chemical dosimeters of the colorimetric type is presented. A single fluid composition is used consisting of a chlorinated hydrocarbon, an acidimetric dye, a normalizer and water. Suitable chlorinated hydrocarbons are carbon tetrachloride, chloroform, trichloroethylene, trichlorethane, ethylene dichioride and tetracbloroethylene. Suitable acidimetric indicator dyes are phenol red, bromcresol purple, and creosol red. Suitable normallzers are resorcinol, geraniol, meta cresol, alpha -tocopberol, and alpha -naphthol.

A method to assess the allocation suitability of recreational activities: An economic approach

NASA Astrophysics Data System (ADS)

Wang, Hsiao-Lin

1996-03-01

Most existing methods of planning focus on development of a recreational area; less consideration is placed on the allocation of recreational activities within a recreational area. Most existing research emphasizes the economic benefits of developing a recreational area; few authors assessed the allocation suitability of recreational activities from an economic point of view. The purpose of this work was to develop a model to assess the allocation suitability of recreational activities according to the application of a concept of analysis of cost and benefit under a premise of ecological concern. The model was verified with a case study of Taiwan. We suggest that the proposed model should form a critical part of recreational planning.

Polymer scaffold degradation control via chemical control

DOEpatents

Hedberg-Dirk, Elizabeth L.; Dirk, Shawn; Cicotte, Kirsten

2016-01-05

A variety of polymers and copolymers suitable for use as biologically compatible constructs and, as a non-limiting specific example, in the formation of degradable tissue scaffolds as well methods for synthesizing these polymers and copolymers are described. The polymers and copolymers have degradation rates that are substantially faster than those of previously described polymers suitable for the same uses. Copolymers having a synthesis route which enables one to fine tune the degradation rate by selecting the specific stoichiometry of the monomers in the resulting copolymer are also described. The disclosure also provides a novel synthesis route for maleoyl chloride which yields monomers suitable for use in the copolymer synthesis methods described herein.

Preliminary Study into Shell Mold Casting of Nominal 60-Nitinol Alloy

DTIC Science & Technology

The present study was initiated to determine the feasibility of shell mold casting nominal 60- Nitinol into suitable EOD (Explosive Ordnance Disposal...surface finish and definition and property response of cast alloy. Based upon the results, 60- Nitinol appears quite suited to shell molding and a...concern lies in the casting porosity associated with the relatively large liquid-to-solid shrinkage of nominal 60- Nitinol .

COATED ALLOYS

DOEpatents

Harman, C.G.; O'Bannon, L.S.

1958-07-15

A coating is described for iron group metals and alloys, that is particularly suitable for use with nickel containing alloys. The coating is glassy in nature and consists of a mixture containing an alkali metal oxide, strontium oxide, and silicon oxide. When the glass coated nickel base metal is"fired'' at less than the melting point of the coating, it appears the nlckel diffuses into the vitreous coating, thus providing a closely adherent and protective cladding.

Going beyond Google for Faster and Smarter Web Searching

ERIC Educational Resources Information Center

Vine, Rita

2004-01-01

With more than 4 billion web pages in its database, Google is suitable for many different kinds of searches. When you know what you are looking for, Google can be a pretty good first choice, as long as you want to search a word pattern that can be expected to appear on any results pages. The problem starts when you don't know exactly what you're…

Monitoring of monosaccharides, oligosaccharides, ethanol and glycerol during wort fermentation by biosensors, HPLC and spectrophotometry.

PubMed

Monošík, Rastislav; Magdolen, Peter; Stredanský, Miroslav; Šturdík, Ernest

2013-05-01

The aim of the present study was to analyze sugar levels (namely maltose, maltotriose, glucose and fructose) and alcohols (ethanol and glycerol) during the fermentation process in wort samples by amperometric enzymatic biosensors developed by our research group for industrial application, HPLC and spectrophotometry, and to compare the suitability of the presented methods for determination of individual analytes. We can conclude that for the specific monitoring of maltose or maltotriose only the HPLC method was suitable. On the other hand, biosensors and spectrophotometry reflected a decrease in total sugar concentration better and were able to detect both glucose and fructose in the later stages of fermentation, while HPLC was not. This can be attributed to the low detection limits and good sensitivity of the proposed methods. For the ethanol and glycerol analysis all methods proved to be suitable. However, concerning the cost expenses and time analysis, biosensors represented the best option. Copyright © 2012 Elsevier Ltd. All rights reserved.

Update on diagnostic value of breath test in gastrointestinal and liver diseases

PubMed Central

Siddiqui, Imran; Ahmed, Sibtain; Abid, Shahab

2016-01-01

In the field of gastroenterology, breath tests (BTs) are used intermittently as diagnostic tools that allow indirect, non-invasive and relatively less cumbersome evaluation of several disorders by simply quantifying the appearance in exhaled breath of a metabolite of a specific substrate administered. The aim of this review is to have an insight into the principles, methods of analysis and performance parameters of various hydrogen, methane and carbon BTs which are available for diagnosing gastrointestinal disorders such as Helicobacter pylori infection, small intestinal bacterial overgrowth, and carbohydrate malabsorption. Evaluation of gastric emptying is routinely performed by scintigraphy which is however, difficult to perform and not suitable for children and pregnant women, this review has abridged the 13C-octanoic acid test in comparison to scintigraphy and has emphasized on its working protocol and challenges. A new development such as electronic nose test is also highlighted. Moreover we have also explored the limitations and constraints restraining the wide use of these BT. We conclude that breath testing has an enormous potential to be used as a diagnostic modality. In addition it offers distinct advantages over the traditional invasive methods commonly employed. PMID:27574563

Multivariate Analysis of the Determinants of the End-Product Quality of Manure-Based Composts and Vermicomposts Using Bayesian Network Modelling

PubMed Central

Faverial, Julie; Cornet, Denis; Paul, Jacky

2016-01-01

Previous studies indicated that the quality of tropical composts is poorer than that of composts produced in temperate regions. The aim of this study was to test the type of manure, the use of co-composting with green waste, and the stabilization method for their ability to improve compost quality in the tropics. We produced 68 composts and vermicomposts that were analysed for their C, lignin and NPK contents throughout the composting process. Bayesian networks were used to assess the mechanisms controlling compost quality. The concentration effect, for C and lignin, and the initial blend quality, for NPK content, were the main factors affecting compost quality. Cattle manure composts presented the highest C and lignin contents, and poultry litter composts exhibited the highest NPK content. Co-composting improved quality by enhancing the concentration effect, which reduced the impact of C and nutrient losses. Vermicomposting did not improve compost quality; co-composting without earthworms thus appears to be a suitable stabilization method under the conditions of this study because it produced high quality composts and is easier to implement. PMID:27314950

An improved method for Agrobacterium rhizogenes-mediated transformation of tomato suitable for the study of arbuscular mycorrhizal symbiosis.

PubMed

Ho-Plágaro, Tania; Huertas, Raúl; Tamayo-Navarrete, María I; Ocampo, Juan A; García-Garrido, José M

2018-01-01

Solanum lycopersicum , an economically important crop grown worldwide, has been used as a model for the study of arbuscular mycorrhizal (AM) symbiosis in non-legume plants for several years and several cDNA array hybridization studies have revealed specific transcriptomic profiles of mycorrhizal tomato roots. However, a method to easily screen candidate genes which could play an important role during tomato mycorrhization is required. We have developed an optimized procedure for composite tomato plant obtaining achieved through Agrobacterium rhizogenes -mediated transformation. This protocol involves the unusual in vitro culture of composite plants between two filter papers placed on the culture media. In addition, we show that DsRed is an appropriate molecular marker for the precise selection of cotransformed tomato hairy roots . S. lycopersicum composite plant hairy roots appear to be colonized by the AM fungus Rhizophagus irregularis in a manner similar to that of normal roots, and a modified construct useful for localizing the expression of promoters putatively associated with mycorrhization was developed and tested. In this study, we present an easy, fast and low-cost procedure to study AM symbiosis in tomato roots.

Visualization of human heart conduction system by means of fluorescence spectroscopy

NASA Astrophysics Data System (ADS)

Venius, Jonas; Bagdonas, Saulius; Žurauskas, Edvardas; Rotomskis, Ricardas

2011-10-01

The conduction system of the heart is a specific muscular tissue, where a heartbeat signal originates and initiates the depolarization of the ventricles. The muscular origin makes it complicated to distinguish the conduction system from the surrounding tissues. A surgical intervention can lead to the accidental harm of the conduction system, which may eventually result in a dangerous obstruction of the heart functionality. Therefore, there is an immense necessity for developing a helpful method to visualize the conduction system during the operation time. The specimens for the spectroscopic studies were taken from nine diverse human hearts. The localization of distinct types of the tissue was preliminary marked by the pathologist and approved histologically after the spectral measurements. Variations in intensity, as well as in shape, were detected in autofluorescence spectra of different heart tissues. The most distinct differences were observed between the heart conduction system and the surrounding tissues under 330 and 380 nm excitation. The spectral region around 460 nm appeared to be the most suitable for an unambiguous differentiation of the human conduction system avoiding the absorption peak of blood. The visualization method, based on the intensity ratios calculated for two excitation wavelengths, was also demonstrated.

Influence of nickel substitution on crystal structure and magnetic properties of strontium ferrite preparation via sol-gel auto-combustion route

NASA Astrophysics Data System (ADS)

Roohani, Ebrahim; Arabi, Hadi; Sarhaddi, Reza

2018-01-01

In this research, SrFe12-xNixO19 (x = 0 - 1) hexagonal ferrites were prepared by sol-gel auto-combustion method. Effect of Ni substitution on structural, morphological and magnetic properties of nanoparticles was investigated by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Transmission electron microscopy (TEM) and vibrating sample magnetometer (VSM), respectively. The XRD results confirmed that all samples with x ≤ 0.5 have single phase M-type strontium ferrite structure, whereas for the SrFe12-xNixO19 samples with x > 0.5, the spinel NiFe2O4 phase has also appeared. The lattice parameters and crystallite sizes of the powders were concluded from the XRD data and Williamson-Hall method. Magnetic analyses showed that the coercivity of powders decreased from 5672 Oe to 639 Oe while the saturation magnetization increased from 74 emu/g to 81 emu/g with nickel substitution. The results of this study suggest that the strontium hexaferrites doped with Ni are suitable for applications in high density magnetic recording media as well as microwave devices because of their promising magnetic properties.

Numerical modeling of the transitional boundary layer over a flat plate

NASA Astrophysics Data System (ADS)

Ivanov, Dimitry; Chorny, Andrei

2015-11-01

Our example is connected with fundamental research on understanding how an initially laminar boundary layer becomes turbulent. We have chosen the flow over a flat plate as a prototype for boundary-layer flows around bodies. Special attention was paid to the near-wall region in order to capture all levels of the boundary layer. In this study, the numerical software package OpenFOAM has been used in order to solve the flow field. The results were used in a comparative study with data obtained from Large Eddy Simulation (LES). The composite SGS-wall model is presently incorporated into a computer code suitable for the LES of developing flat-plate boundary layers. Presently this model is extended to the LES of the zero-pressure gradient, flat-plate turbulent boundary layer. In current study the time discretization is based on a second order Crank-Nicolson/Adams-Bashforth method. LES solver using Smagorinsky and the one-equation LES turbulence models. The transition models significantly improve the prediction of the onset location compared to the fully turbulent models.LES methods appear to be the most promising new tool for the design and analysis of flow devices including transition regions of the turbulent flow.

Non-radioactive TRF assay modifications to improve telomeric DNA detection efficiency in plants

PubMed Central

Nigmatullina, Liliia R.; Sharipova, Margarita R.; Shakirov, Eugene V.

2016-01-01

The length of telomeric DNA is often considered a cellular biomarker of aging and general health status. Several telomere length measuring assays have been developed, of which the most common is the Telomere Restriction Fragment (TRF) analysis, which typically involves the use of radioactively labeled oligonucleotide probes. While highly effective, this method potentially poses substantial health concerns and generates radioactive waste. Digoxigenin (DIG) alternatives to radioactive probes have been developed and used successfully in a number of assays. Here we optimize the DIG protocol to measure telomere length in the model plant Arabidopsis thaliana and present evidence that this approach can be used successfully to efficiently and accurately measure telomere length in plants. Specifically, hybridization temperature of 42 °C instead of the typical 55 °C appears to generate stronger signals. In addition, DIG incorporation at 5′-end instead of 3′-end of the labeled oligonucleotide greatly enhances signal. We conclude that non-radioactive TRF assays can be as efficient as radioactive methods in detecting and measuring telomere length in plants, making this assay suitable for medical and research laboratories unable to utilize radioactivity due to hazardous waste disposal and safety concerns. PMID:28133587

Head repositioning accuracy to neutral: a comparative study of error calculation.

PubMed

Hill, Robert; Jensen, Pål; Baardsen, Tor; Kulvik, Kristian; Jull, Gwendolen; Treleaven, Julia

2009-02-01

Deficits in cervical proprioception have been identified in subjects with neck pain through the measure of head repositioning accuracy (HRA). Nevertheless there appears to be no general consensus regarding the construct of measurement of error used for calculating HRA. This study investigated four different mathematical methods of measurement of error to determine if there were any differences in their ability to discriminate between a control group and subjects with a whiplash associated disorder. The four methods for measuring cervical joint position error were calculated using a previous data set consisting of 50 subjects with whiplash complaining of dizziness (WAD D), 50 subjects with whiplash not complaining of dizziness (WAD ND) and 50 control subjects. The results indicated that no one measure of HRA uniquely detected or defined the differences between the whiplash and control groups. Constant error (CE) was significantly different between the whiplash and control groups from extension (p<0.05). Absolute errors (AEs) and root mean square errors (RMSEs) demonstrated differences between the two WAD groups in rotation trials (p<0.05). No differences were seen with variable error (VE). The results suggest that a combination of AE (or RMSE) and CE are probably the most suitable measures for analysis of HRA.

Assessment of the use of latissimus dorsi restoration during modified radical mastectomy in breast cancer patients.

PubMed

Yang, Chao; Wang, Xinle; Zhang, Geng; Yang, Liu; Guo, Xuan; Wang, Xue; Song, Zhenchuan

2017-12-01

The incision area of modified radical mastectomy in breast cancer patients is associated with subcutaneous effusion and skin flap necrosis as the most common complications. The aim of the present study was to assess the effect of latissimus dorsi restoration during modified radical mastectomy in breast cancer patients by evaluating 365 cases. Among these cases, 185 received modified radical mastectomy combined with intraoperative latissimus dorsi restoration, while 180 received modified radical mastectomy alone. The flap tension, drainage fluid amount and extubation time were compared between the two methods. The flap tension in patients who received modified radical mastectomy combined with intraoperative latissimus dorsi restoration was significantly lower and the blood supply was better. After surgery, the drainage fluid amount was also significantly lower in these patients compared with the control group. Furthermore, the mean time to drainage tube removal was significantly shorter in these patients and the postoperative cosmetic outcome was superior. Thus, it was concluded that modified radical mastectomy combined with intraoperative latissimus dorsi restoration in breast cancer patients was associated with reduced drainage fluid effusion, shorter hospitalization time and decreased flap tension. Overall, this method appears to be potentially suitable for extensive application in the clinical setting.

A two-step real-time PCR assay for quantitation and genotyping of human parvovirus 4.

PubMed

Väisänen, E; Lahtinen, A; Eis-Hübinger, A M; Lappalainen, M; Hedman, K; Söderlund-Venermo, M

2014-01-01

Human parvovirus 4 (PARV4) of the family Parvoviridae was discovered in a plasma sample of a patient with an undiagnosed acute infection in 2005. Currently, three PARV4 genotypes have been identified, however, with an unknown clinical significance. Interestingly, these genotypes seem to differ in epidemiology. In Northern Europe, USA and Asia, genotypes 1 and 2 have been found to occur mainly in persons with a history of injecting drug use or other parenteral exposure. In contrast, genotype 3 appears to be endemic in sub-Saharan Africa, where it infects children and adults without such risk behaviour. In this study, a novel straightforward and cost-efficient molecular assay for both quantitation and genotyping of PARV4 DNA was developed. The two-step method first applies a single-probe pan-PARV4 qPCR for screening and quantitation of this relatively rare virus, and subsequently, only the positive samples undergo a real-time PCR-based multi-probe genotyping. The new qPCR-GT method is highly sensitive and specific regardless of the genotype, and thus being suitable for studying the clinical impact and occurrence of the different PARV4 genotypes. Copyright © 2013 Elsevier B.V. All rights reserved.

Three-dimensional CT Venography: A Diagnostic Modality for the Preoperative Assessment of Patients with Varicose Veins

PubMed Central

Sato, Katsutoshi; Orihashi, Kazumasa; Takahashi, Shinya; Takasaki, Taiichi; Kurosaki, Tatsuya; Imai, Katsuhiko; Ishifuro, Minoru; Sueda, Taijiro

2011-01-01

Objective: We preoperatively assessed varicose veins by means of computed tomography (CT) with contrast injection in the veins of the lower extremity (CT venography). This paper reports the procedures, results and implications of CT venography from the surgical aspect. Methods: A total of 48 legs in 39 patients were examined. Contrast medium was diluted ten-fold and injected into the lower extremity veins, often using a dual route of injection. The images were reconstructed with the volume-rendering method. Results: CT venography clearly visualized the veins with a small amount of contrast medium and facilitated the identification of anatomy that was not suitable for passing the stripper. In addition, CT venography helped identify unusual types of varicose veins or uncommon sites of inflow of small saphenous veins. Such information was helpful for avoiding unexpected vascular injury or for minimizing skin incision. Dual-route injection was beneficial to minimize the blind zones. Doppler ultrasound could be more focused on hemodynamic assessment and determination of incision sites. Conclusions: CT Venography is feasible in all cases of varicose veins. When performed in conjunction with ultrasonography, it appears to facilitate the safe and efficient treatment of various types of varicose veins. PMID:23555458

Computer-generated holograms (CGH) realization: the integration of dedicated software tool with digital slides printer

NASA Astrophysics Data System (ADS)

Guarnieri, Vittorio; Francini, Franco

1997-12-01

Last generation of digital printer is usually characterized by a spatial resolution enough high to allow the designer to realize a binary CGH directly on a transparent film avoiding photographic reduction techniques. These devices are able to produce slides or offset prints. Furthermore, services supplied by commercial printing company provide an inexpensive method to rapidly verify the validity of the design by means of a test-and-trial process. Notably, this low-cost approach appears to be suitable for a didactical environment. On the basis of these considerations, a set of software tools able to design CGH's has been developed. The guidelines inspiring the work have been the following ones: (1) ray-tracing approach, considering the object to be reproduced as source of spherical waves; (2) Optimization and speed-up of the algorithms used, in order to produce a portable code, runnable on several hardware platforms. In this paper calculation methods to obtain some fundamental geometric functions (points, lines, curves) are described. Furthermore, by the juxtaposition of these primitives functions it is possible to produce the holograms of more complex objects. Many examples of generated CGHs are presented.

A prospective study of outcome from rubber band ligation of piles.

PubMed

Longman, R J; Thomson, W H F

2006-02-01

With the recent introduction of stapled anopexy it is timely to review the benefits of existing treatment options for piles. This study investigates the effectiveness and safety of rubber band ligation (RBL) of piles in the outpatient setting. Two hundred and fifty-two consecutive patients referred with piles in an 18-month period were studied prospectively. In those patients deemed suitable for banding of piles, data were collected on symptoms, proctoscopic appearance and degree of piles. Short and long-term outcome data were recorded for success of treatment and complications. Of 203 patients considered suitable and who attended for RBL, 176 kept their follow-up appointment. One hundred and forty-eight (84%) had been rendered symptom-free. A third of patients, however, had proctoscopic evidence of persistent piles, whilst in half of those patients with continuing symptoms the anal cushions appeared normal. Six (3%) patients had suffered a complication. Long-term follow-up by questionnaire found that 44% of respondents remained asymptomatic at a median of 46 months from banding. Six (5%) of 117 responders to the questionnaire had, though previously normal, suffered a postbanding impairment of continence. Most patients with piles of any degree can be safely managed by rubber band ligation, but return of symptoms in the long term affects more than half of patients treated.

Carbon monoxide sensor and method of use thereof

DOEpatents

McDaniel; Anthony H. , Medlin; J. Will , Bastasz; Robert J.

2007-09-04

Carbon monoxide sensors suitable for use in hydrogen feed streams and methods of use thereof are disclosed. The sensors are palladium metal/insulator/semiconductor (Pd-MIS) sensors which may possess a gate metal layer having uniform, Type 1, or non-uniform, Type 2, film morphology. Type 1 sensors display an increased sensor response in the presence of carbon monoxide while Type 2 sensors display a decreased response to carbon monoxide. The methods and sensors disclosed herein are particularly suitable for use in proton exchange membrane fuel cells (PEMFCs).

Method For Screening Microcrystallizations For Crystal Formation

DOEpatents

Santarsiero, Bernard D. , Stevens, Raymond C. , Schultz, Peter G. , Jaklevic, Joseph M. , Yegian, Derek T. , Cornell, Earl W. , Nordmeyer, Robert A.

2003-10-07

A method is provided for performing array microcrystallizations to determine suitable crystallization conditions for a molecule, the method comprising: forming an array of microcrystallizations, each microcrystallization comprising a drop comprising a mother liquor solution whose composition varies within the array and a molecule to be crystallized, the drop having a volume of less than 1 microliter; storing the array of microcrystallizations under conditions suitable for molecule crystals to form in the drops in the array; and detecting molecule crystal formation in the drops by taking images of the drops.

Brief overview of the various families of grouts and their aplications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nandts, A.

1989-04-01

It is difficult to maintain an up-to-date overview of all the grouts presently used on the international market. Better grouts are continuously developed and more formulators are making their appearance. Consequently, it is difficult to clearly define all of the products in the industry. This topic has been the subject of numerous papers and textbooks. Most authors, however, only focus on their fields of interest: applications in geotechnical, or rehabilitation, or seepage control in civil engineering, oil or mining industry. There has been a limited transfer of technology from one field to the other because of the enormous differences inmore » magnitude, site conditions and consequently the application techniques. The tools an engineer has are: his expertise in grouting and engineering background, equipment available or to be designed or modified to carry out a particular job, relevant data available from other sciences, and products with a variety of characteristics. This paper concentrates on product selection. The most suitable product for a particular project requires a good understanding of the general chemical and mechanical characteristics of the grout. The grouts have been classified into four categories for the purpose of this paper. There may be other methods of classification; however, this is only an attempt to help the industry with the selection of the most suitable grout for a given application. The four categories are: suspension grouts, chemical grouts, hot melts, and precipitation grouts. 1 fig.« less

[Application of an improved model of a job-matching platform for nurses].

PubMed

Huang, Way-Ren; Lin, Chiou-Fen

2015-04-01

The three-month attrition rate for new nurses in Taiwan remains high. Many hospitals rely on traditional recruitment methods to find new nurses, yet it appears that their efficacy is less than ideal. To effectively solve this manpower shortage, a nursing resource platform is a project worth developing in the future. This study aimed to utilize a quality-improvement model to establish communication between hospitals and nursing students and create a customized employee-employer information-matching platform to help nursing students enter the workforce. This study was structured around a quality-improvement model and used current situation analysis, literature review, focus-group discussions, and process re-engineering to formulate necessary content for a job-matching platform for nursing. The concept of an academia-industry strategic alliance helped connect supply and demand within the same supply chain. The nurse job-matching platform created in this study provided job flexibility as well as job suitability assessments and continued follow-up and services for nurses after entering the workforce to provide more accurate matching of employers and employees. The academia-industry strategic alliance, job suitability, and long-term follow-up designed in this study are all new features in Taiwan's human resource service systems. The proposed human resource process re-engineering provides nursing students facing graduation with a professionally managed human resources platform. Allowing students to find an appropriate job prior to graduation will improve willingness to work and employee retention.

Transport of fluorobenzoate tracers in a vegetated hydrologic control volume: 1. Experimental results

NASA Astrophysics Data System (ADS)

Queloz, Pierre; Bertuzzo, Enrico; Carraro, Luca; Botter, Gianluca; Miglietta, Franco; Rao, P. S. C.; Rinaldo, Andrea

2015-04-01

This paper reports about the experimental evidence collected on the transport of five fluorobenzoate tracers injected under controlled conditions in a vegetated hydrologic volume, a large lysimeter (fitted with load cells, sampling ports, and an underground chamber) where two willows prompting large evapotranspiration fluxes had been grown. The relevance of the study lies in the direct and indirect measures of the ways in which hydrologic fluxes, in this case, evapotranspiration from the upper surface and discharge from the bottom drainage, sample water and solutes in storage at different times under variable hydrologic forcings. Methods involve the accurate control of hydrologic inputs and outputs and a large number of suitable chemical analyses of water samples in discharge waters. Mass extraction from biomass has also been performed ex post. The results of the 2 year long experiment established that our initial premises on the tracers' behavior, known to be sorption-free under saturated conditions which we verified in column leaching tests, were unsuitable as large differences in mass recovery appeared. Issues on reactivity thus arose and were addressed in the paper, in this case attributed to microbial degradation and solute plant uptake. Our results suggest previously unknown features of fluorobenzoate compounds as hydrologic tracers, potentially interesting for catchment studies owing to their suitability for distinguishable multiple injections, and an outlook on direct experimental closures of mass balance in hydrologic transport volumes involving fluxes that are likely to sample differently stored water and solutes.

Suitable Site Selection of Small Dams Using Geo-Spatial Technique: a Case Study of Dadu Tehsil, Sindh

NASA Astrophysics Data System (ADS)

Khalil, Zahid

2016-07-01

Decision making about identifying suitable sites for any project by considering different parameters, is difficult. Using GIS and Multi-Criteria Analysis (MCA) can make it easy for those projects. This technology has proved to be an efficient and adequate in acquiring the desired information. In this study, GIS and MCA were employed to identify the suitable sites for small dams in Dadu Tehsil, Sindh. The GIS software is used to create all the spatial parameters for the analysis. The parameters that derived are slope, drainage density, rainfall, land use / land cover, soil groups, Curve Number (CN) and runoff index with a spatial resolution of 30m. The data used for deriving above layers include 30 meter resolution SRTM DEM, Landsat 8 imagery, and rainfall from National Centre of Environment Prediction (NCEP) and soil data from World Harmonized Soil Data (WHSD). Land use/Land cover map is derived from Landsat 8 using supervised classification. Slope, drainage network and watershed are delineated by terrain processing of DEM. The Soil Conservation Services (SCS) method is implemented to estimate the surface runoff from the rainfall. Prior to this, SCS-CN grid is developed by integrating the soil and land use/land cover raster. These layers with some technical and ecological constraints are assigned weights on the basis of suitability criteria. The pair wise comparison method, also known as Analytical Hierarchy Process (AHP) is took into account as MCA for assigning weights on each decision element. All the parameters and group of parameters are integrated using weighted overlay in GIS environment to produce suitable sites for the Dams. The resultant layer is then classified into four classes namely, best suitable, suitable, moderate and less suitable. This study reveals a contribution to decision making about suitable sites analysis for small dams using geo-spatial data with minimal amount of ground data. This suitability maps can be helpful for water resource management organizations in determination of feasible rainwater harvesting structures (RWH).

Excess Lead-210 and Plutonium-239+240: Two suitable radiogenic soil erosion tracers for mountain grassland sites.

PubMed

Meusburger, K; Porto, P; Mabit, L; La Spada, C; Arata, L; Alewell, C

2018-01-01

The expected growing population and challenges associated with globalisation will increase local food and feed demands and enhance the pressure on local and regional upland soil resources. In light of these potential future developments it is necessary to define sustainable land use and tolerable soil loss rates with methods applicable and adapted to mountainous areas. Fallout-radionuclides (FRNs) are proven techniques to increase our knowledge about the status and resilience of agro-ecosystems. However, the use of the Caesium-137 ( 137 Cs) method is complicated in the European Alps due to its heterogeneous input and the timing of the Chernobyl fallout, which occurred during a few single rain events on partly snow covered ground. Other radioisotopic techniques have been proposed to overcome these limitations. The objective of this study is to evaluate the suitability of excess Lead-210 ( 210 Pb ex ) and Plutonium-239+240 ( 239+240 Pu) as soil erosion tracers for three different grassland management types at the steep slopes (slope angles between 35 and 38°) located in the Central Swiss Alps. All three FRNs identified pastures as having the highest mean (± standard deviation) net soil loss of -6.7 ± 1.1, -9.8 ± 6.8 and -7.0 ± 5.2 Mg ha -1 yr -1 for 137 Cs, 210 Pb ex and 239+240 Pu, respectively. A mean soil loss of -5.7 ± 1.5, -5.2 ± 1.5 and-5.6 ± 2.1 was assessed for hayfields and the lowest rates were established for pastures with dwarf-shrubs (-5.2 ± 2.5, -4.5 ± 2.5 and -3.3 ± 2.4 Mg ha -1 yr -1 for 137 Cs, 210 Pb ex and 239+240 Pu, respectively). These rates, evaluated at sites with an elevated soil erosion risk exceed the respective soil production rates. Among the three FRN methods used, 239+240 Pu appears as the most promising tracer in terms of measurement uncertainty and reduced small scale variability (CV of 13%). Despite a higher level of uncertainty, 210 Pb ex produced comparable results, with a wide range of erosion rates sensitive to changes in grassland management. 210 Pb ex can then be as well considered as a suitable soil tracer to investigate alpine agroecosystems. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

On the stability of projection methods for the incompressible Navier-Stokes equations based on high-order discontinuous Galerkin discretizations

NASA Astrophysics Data System (ADS)

Fehn, Niklas; Wall, Wolfgang A.; Kronbichler, Martin

2017-12-01

The present paper deals with the numerical solution of the incompressible Navier-Stokes equations using high-order discontinuous Galerkin (DG) methods for discretization in space. For DG methods applied to the dual splitting projection method, instabilities have recently been reported that occur for small time step sizes. Since the critical time step size depends on the viscosity and the spatial resolution, these instabilities limit the robustness of the Navier-Stokes solver in case of complex engineering applications characterized by coarse spatial resolutions and small viscosities. By means of numerical investigation we give evidence that these instabilities are related to the discontinuous Galerkin formulation of the velocity divergence term and the pressure gradient term that couple velocity and pressure. Integration by parts of these terms with a suitable definition of boundary conditions is required in order to obtain a stable and robust method. Since the intermediate velocity field does not fulfill the boundary conditions prescribed for the velocity, a consistent boundary condition is derived from the convective step of the dual splitting scheme to ensure high-order accuracy with respect to the temporal discretization. This new formulation is stable in the limit of small time steps for both equal-order and mixed-order polynomial approximations. Although the dual splitting scheme itself includes inf-sup stabilizing contributions, we demonstrate that spurious pressure oscillations appear for equal-order polynomials and small time steps highlighting the necessity to consider inf-sup stability explicitly.

Improved colour matching technique for fused nighttime imagery with daytime colours

NASA Astrophysics Data System (ADS)

Hogervorst, Maarten A.; Toet, Alexander

2016-10-01

Previously, we presented a method for applying daytime colours to fused nighttime (e.g., intensified and LWIR) imagery (Toet and Hogervorst, Opt.Eng. 51(1), 2012). Our colour mapping not only imparts a natural daylight appearance to multiband nighttime images but also enhances the contrast and visibility of otherwise obscured details. As a result, this colourizing method leads to increased ease of interpretation, better discrimination and identification of materials, faster reaction times and ultimately improved situational awareness (Toet e.a., Opt.Eng.53(4), 2014). A crucial step in this colouring process is the choice of a suitable colour mapping scheme. When daytime colour images and multiband sensor images of the same scene are available the colour mapping can be derived from matching image samples (i.e., by relating colour values to sensor signal intensities). When no exact matching reference images are available the colour transformation can be derived from the first-order statistical properties of the reference image and the multiband sensor image (Toet, Info. Fus. 4(3), 2003). In the current study we investigated new colour fusion schemes that combine the advantages of the both methods, using the correspondence between multiband sensor values and daytime colours (1st method) in a smooth transformation (2nd method). We designed and evaluated three new fusion schemes that focus on: i) a closer match with the daytime luminances, ii) improved saliency of hot targets and iii) improved discriminability of materials

GIS habitat analysis for lesser prairie-chickens in southeastern New Mexico.

PubMed

Johnson, Kristine; Neville, Teri B; Neville, Paul

2006-12-04

We conducted Geographic Information System (GIS) habitat analyses for lesser prairie-chicken (LPCH, Tympanuchus pallidicinctus) conservation planning. The 876,799 ha study area included most of the occupied habitat for the LPCH in New Mexico. The objectives were to identify and quantify: 1. suitable LPCH habitat in New Mexico, 2. conversion of native habitats, 3. potential for habitat restoration, and 4. unsuitable habitat available for oil and gas activities. We found 16% of suitable habitat (6% of the study area) distributed in 13 patches of at least 3,200 ha and 11% of suitable habitat (4% of the study area) distributed in four patches over 7,238 ha. The area converted from native vegetation types comprised 17% of the study area. Ninety-five percent of agricultural conversion occurred on private lands in the northeastern corner of the study area. Most known herbicide-related conversions (82%) occurred in rangelands in the western part of the study area, on lands managed primarily by the US Bureau of Land Management (BLM). We identified 88,190 ha (10% of the study area) of habitats with reasonable restoration potential. Sixty-two percent of the primary population area (PPA) contained occupied, suitable, or potentially suitable habitat, leaving 38% that could be considered for oil and gas development. Although suitable LPCH habitat appears at first glance to be abundant in southeastern New Mexico, only a fraction of apparently suitable vegetation types constitute quality habitat. However, we identified habitat patches that could be restored through mesquite control or shin-oak reintroduction. The analysis also identified areas of unsuitable habitat with low restoration potential that could be targeted for oil and gas exploration, in lieu of occupied, high-quality habitats. Used in combination with GIS analysis and current LPCH population data, the habitat map represents a powerful conservation and management tool.

GIS habitat analysis for lesser prairie-chickens in southeastern New Mexico

PubMed Central

Johnson, Kristine; Neville, Teri B; Neville, Paul

2006-01-01

Background We conducted Geographic Information System (GIS) habitat analyses for lesser prairie-chicken (LPCH, Tympanuchus pallidicinctus) conservation planning. The 876,799 ha study area included most of the occupied habitat for the LPCH in New Mexico. The objectives were to identify and quantify: 1. suitable LPCH habitat in New Mexico, 2. conversion of native habitats, 3. potential for habitat restoration, and 4. unsuitable habitat available for oil and gas activities. Results We found 16% of suitable habitat (6% of the study area) distributed in 13 patches of at least 3,200 ha and 11% of suitable habitat (4% of the study area) distributed in four patches over 7,238 ha. The area converted from native vegetation types comprised 17% of the study area. Ninety-five percent of agricultural conversion occurred on private lands in the northeastern corner of the study area. Most known herbicide-related conversions (82%) occurred in rangelands in the western part of the study area, on lands managed primarily by the US Bureau of Land Management (BLM). We identified 88,190 ha (10% of the study area) of habitats with reasonable restoration potential. Sixty-two percent of the primary population area (PPA) contained occupied, suitable, or potentially suitable habitat, leaving 38% that could be considered for oil and gas development. Conclusion Although suitable LPCH habitat appears at first glance to be abundant in southeastern New Mexico, only a fraction of apparently suitable vegetation types constitute quality habitat. However, we identified habitat patches that could be restored through mesquite control or shin-oak reintroduction. The analysis also identified areas of unsuitable habitat with low restoration potential that could be targeted for oil and gas exploration, in lieu of occupied, high-quality habitats. Used in combination with GIS analysis and current LPCH population data, the habitat map represents a powerful conservation and management tool. PMID:17144922

Automated encoding of clinical documents based on natural language processing.

PubMed

Friedman, Carol; Shagina, Lyudmila; Lussier, Yves; Hripcsak, George

2004-01-01

The aim of this study was to develop a method based on natural language processing (NLP) that automatically maps an entire clinical document to codes with modifiers and to quantitatively evaluate the method. An existing NLP system, MedLEE, was adapted to automatically generate codes. The method involves matching of structured output generated by MedLEE consisting of findings and modifiers to obtain the most specific code. Recall and precision applied to Unified Medical Language System (UMLS) coding were evaluated in two separate studies. Recall was measured using a test set of 150 randomly selected sentences, which were processed using MedLEE. Results were compared with a reference standard determined manually by seven experts. Precision was measured using a second test set of 150 randomly selected sentences from which UMLS codes were automatically generated by the method and then validated by experts. Recall of the system for UMLS coding of all terms was .77 (95% CI.72-.81), and for coding terms that had corresponding UMLS codes recall was .83 (.79-.87). Recall of the system for extracting all terms was .84 (.81-.88). Recall of the experts ranged from .69 to .91 for extracting terms. The precision of the system was .89 (.87-.91), and precision of the experts ranged from .61 to .91. Extraction of relevant clinical information and UMLS coding were accomplished using a method based on NLP. The method appeared to be comparable to or better than six experts. The advantage of the method is that it maps text to codes along with other related information, rendering the coded output suitable for effective retrieval.

A Novel Source of Cultured Podocytes

PubMed Central

Da Sacco, Stefano; Lemley, Kevin V.; Sedrakyan, Sargis; Zanusso, Ilenia; Petrosyan, Astgik; Peti-Peterdi, Janos; Burford, James; De Filippo, Roger E.; Perin, Laura

2013-01-01

Amniotic fluid is in continuity with multiple developing organ systems, including the kidney. Committed, but still stem-like cells from these organs may thus appear in amniotic fluid. We report having established for the first time a stem-like cell population derived from human amniotic fluid and possessing characteristics of podocyte precursors. Using a method of triple positive selection we obtained a population of cells (hAKPC-P) that can be propagated in vitro for many passages without immortalization or genetic manipulation. Under specific culture conditions, these cells can be differentiated to mature podocytes. In this work we compared these cells with conditionally immortalized podocytes, the current gold standard for in vitro studies. After in vitro differentiation, both cell lines have similar expression of the major podocyte proteins, such as nephrin and type IV collagen, that are characteristic of mature functional podocytes. In addition, differentiated hAKPC-P respond to angiotensin II and the podocyte toxin, puromycin aminonucleoside, in a way typical of podocytes. In contrast to immortalized cells, hAKPC-P have a more nearly normal cell cycle regulation and a pronounced developmental pattern of specific protein expression, suggesting their suitability for studies of podocyte development for the first time in vitro. These novel progenitor cells appear to have several distinct advantages for studies of podocyte cell biology and potentially for translational therapies. PMID:24349133

Seasonal Variations of the Antioxidant Composition in Ground Bamboo Sasa argenteastriatus Leaves

PubMed Central

Ni, Qinxue; Xu, Guangzhi; Wang, Zhiqiang; Gao, Qianxin; Wang, Shu; Zhang, Youzuo

2012-01-01

Sasa argenteastriatus, with abundant active compounds and high antioxidant activity in leaves, is a new leafy bamboo grove suitable for exploitation. To utilize it more effectively and scientifically, we investigate the seasonal variations of antioxidant composition in its leaves and antioxidant activity. The leaves of Sasa argenteastriatus were collected on the 5th day of each month in three same-sized sample plots from May 2009 to May 2011. The total flavonoids (TF): phenolics (TP) and triterpenoid (TT) of bamboo leaves were extracted and the contents analyzed by UV-spectrophotometer. Our data showed that all exhibited variations with the changing seasons, with the highest levels appearing in November to March. Antioxidant activity was measured using DPPH and FRAP methods. The highest antioxidant activity appeared in December with the lowest in May. Correlation analyses demonstrated that TP and TF exhibited high correlation with bamboo antioxidant activity. Eight bamboo characteristic compounds (orientin, isoorientin, vitexin, homovitexin and p-coumaric acid, chlorogenic acid, caffeic acid, ferulic acid) were determined by RP-HPLC synchronously. We found that chlorogenic acid, isoorientin and vitexin are the main compounds in Sasa argenteastriatus leaves and the content of isovitexin and chlorogenic acid showed a similar seasonal variation with the TF, TP and TT. Our results suggested that the optimum season for harvesting Sasa argenteastriatus leaves is between autumn and winter. PMID:22408451

Assessment of natural enamel lesions with optical coherence tomography in comparison with microfocus x-ray computed tomography.

PubMed

Espigares, Jorge; Sadr, Alireza; Hamba, Hidenori; Shimada, Yasushi; Otsuki, Masayuki; Tagami, Junji; Sumi, Yasunori

2015-01-01

A technology to characterize early enamel lesions is needed in dentistry. Optical coherence tomography (OCT) is a noninvasive method that provides high-resolution cross-sectional images. The aim of this study is to compare OCT with microfocus x-ray computed tomography ([Formula: see text]) for assessment of natural enamel lesions in vitro. Ten human teeth with visible white spot-like changes on the enamel smooth surface and no cavitation (ICDAS code 2) were subjected to imaging by μCT (SMX-100CT, Shimadzu) and 1300-nm swept-source OCT (Dental SS-OCT, Panasonic Health Care). In [Formula: see text], the lesions appeared as radiolucent dark areas, while in SS-OCT, they appeared as areas of increased signal intensity beneath the surface. An SS-OCT attenuation coefficient based on Beer-Lambert law could discriminate lesions from sound enamel. Lesion depth ranged from 175 to [Formula: see text] in SS-OCT. A correlation between [Formula: see text] and SS-OCT was found regarding lesion depth ([Formula: see text], [Formula: see text]) and also surface layer thickness ([Formula: see text], [Formula: see text]). The images obtained clinically in real time using the dental SS-OCT system are suitable for the assessment of natural subsurface lesions and their surface layer, providing comparable images to a laboratory high-resolution [Formula: see text] without the use of x-ray.

Assessment of natural enamel lesions with optical coherence tomography in comparison with microfocus x-ray computed tomography

PubMed Central

Espigares, Jorge; Sadr, Alireza; Hamba, Hidenori; Shimada, Yasushi; Otsuki, Masayuki; Tagami, Junji; Sumi, Yasunori

2015-01-01

Abstract. A technology to characterize early enamel lesions is needed in dentistry. Optical coherence tomography (OCT) is a noninvasive method that provides high-resolution cross-sectional images. The aim of this study is to compare OCT with microfocus x-ray computed tomography (μCT) for assessment of natural enamel lesions in vitro. Ten human teeth with visible white spot-like changes on the enamel smooth surface and no cavitation (ICDAS code 2) were subjected to imaging by μCT (SMX-100CT, Shimadzu) and 1300-nm swept-source OCT (Dental SS-OCT, Panasonic Health Care). In μCT, the lesions appeared as radiolucent dark areas, while in SS-OCT, they appeared as areas of increased signal intensity beneath the surface. An SS-OCT attenuation coefficient based on Beer–Lambert law could discriminate lesions from sound enamel. Lesion depth ranged from 175 to 606  μm in SS-OCT. A correlation between μCT and SS-OCT was found regarding lesion depth (R=0.81, p<0.001) and also surface layer thickness (R=0.76, p<0.005). The images obtained clinically in real time using the dental SS-OCT system are suitable for the assessment of natural subsurface lesions and their surface layer, providing comparable images to a laboratory high-resolution μCT without the use of x-ray. PMID:26158079

[Comparison of two nucleic acid extraction methods for norovirus in oysters].

PubMed

Yuan, Qiao; Li, Hui; Deng, Xiaoling; Mo, Yanling; Fang, Ling; Ke, Changwen

2013-04-01

To explore a convenient and effective method for norovirus nucleic acid extraction from oysters suitable for long-term viral surveillance. Two methods, namely method A (glycine washing and polyethylene glycol precipitation of the virus followed by silica gel centrifugal column) and method B (protease K digestion followed by application of paramagnetic silicon) were compared for their performance in norovirus nucleic acid extraction from oysters. Real-time RT-PCR was used to detect norovirus in naturally infected oysters and in oysters with induced infection. The two methods yielded comparable positive detection rates for the samples, but the recovery rate of the virus was higher with method B than with method A. Method B is a more convenient and rapid method for norovirus nucleic acid extraction from oysters and suitable for long-term surveillance of norovirus.

Process of modifying a cable end

DOEpatents

Roose, L.D.

1995-08-01

End moldings for high-voltage cables are described wherein the dielectric insulator of the cable is heated and molded to conform to a desired shape. As a consequence, high quality substantially bubble-free cable connectors suitable for mating to premanufactured fittings are made. Disclosed are a method for making the cable connectors either in the field or in a factory, molds suitable for use with the method, and the molded cable connectors, themselves. 5 figs.

Evaluation of the suitability of a plant virus, pepper mild mottle virus, as a surrogate of human enteric viruses for assessment of the efficacy of coagulation-rapid sand filtration to remove those viruses.

PubMed

Shirasaki, N; Matsushita, T; Matsui, Y; Yamashita, R

2018-02-01

Here, we evaluated the removal of three representative human enteric viruses - adenovirus (AdV) type 40, coxsackievirus (CV) B5, and hepatitis A virus (HAV) IB - and one surrogate of human caliciviruses - murine norovirus (MNV) type 1 - by coagulation-rapid sand filtration, using water samples from eight water sources for drinking water treatment plants in Japan. The removal ratios of a plant virus (pepper mild mottle virus; PMMoV) and two bacteriophages (MS2 and φX174) were compared with the removal ratios of human enteric viruses to assess the suitability of PMMoV, MS2, and φX174 as surrogates for human enteric viruses. The removal ratios of AdV, CV, HAV, and MNV, evaluated via the real-time polymerase chain reaction (PCR) method, were 0.8-2.5-log 10 when commercially available polyaluminum chloride (PACl, basicity 1.5) and virgin silica sand were used as the coagulant and filter medium, respectively. The type of coagulant affected the virus removal efficiency, but the age of silica sand used in the rapid sand filtration did not. Coagulation-rapid sand filtration with non-sulfated, high-basicity PACls (basicity 2.1 or 2.5) removed viruses more efficiently than the other aluminum-based coagulants. The removal ratios of MS2 were sometimes higher than those of the three human enteric viruses and MNV, whereas the removal ratios of φX174 tended to be smaller than those of the three human enteric viruses and MNV. In contrast, the removal ratios of PMMoV were similar to and strongly correlated with those of the three human enteric viruses and MNV. Thus, PMMoV appears to be a suitable surrogate for human enteric viruses for the assessment of the efficacy of coagulation-rapid sand filtration to remove viruses. Copyright © 2017 Elsevier Ltd. All rights reserved.

Discreet passive explosive detection through 2-sided wave guided fluorescence

DOEpatents

Harper, Ross James; la Grone, Marcus; Fisher, Mark

2012-10-16

The current invention provides a passive sampling device suitable for collecting and detecting the presence of target analytes. In particular, the passive sampling device is suitable for detecting nitro-aromatic compounds. The current invention further provides a passive sampling device reader suitable for determining the collection of target analytes. Additionally, the current invention provides methods for detecting target analytes using the passive sampling device and the passive sampling device reader.

The addition of nanochitosan suspension as filler in carrageenan-tapioca biocomposite film

NASA Astrophysics Data System (ADS)

Rochima, Emma; Fiyanih, Elisah; Afrianto, Eddy; Subhan, Ujang; Praseptiangga, Danar; Panatarani, Camellia; Joni, I. Made

2018-02-01

This research aimed to investigate the effect of nanochitosan (CSNPs) suspension by beads milling method as filler in carrageenan-tapioca biocomposite film. In addition, the antibacterial activity of CSNPs as filler with two food pathogenic bacteria, Staphylococcus aureus and Escherichia coli and then influence of nano fillers for appearance of films were observed. The incorporation of CSNPs suspension with 0.5, 1, 1.5 and 2 (%v/v) in carrageenan-tapioca film exhibited antibacterial activity againts both bacteria. CSNPs had slightly higher antimicrobial activity against E. coli aureus compared to S. aureus at all concentrations due to different mechanisms. Therefore, the best antimicrobial activity was obtained from 1 wt%. Furthermore the best antimicrobial activity was characterized by means of the thickness and transparency. The result showed that the thickness of film was 0.059 mm and the transparency was 87.88. It was concluded that the incorporation of CSNPs suspension 1 wt% in carrageenan-tapioca composite film is suitable for developing active packaging.

Selected Schizosaccharomyces pombe Strains Have Characteristics That Are Beneficial for Winemaking

PubMed Central

Benito, Ángel; Jeffares, Daniel; Palomero, Felipe; Calderón, Fernando; Bai, Feng-Yan; Bähler, Jürg; Benito, Santiago

2016-01-01

At present, wine is generally produced using Saccharomyces yeast followed by Oenococus bacteria to complete malolactic fermentation. This method has some unsolved problems, such as the management of highly acidic musts and the production of potentially toxic products including biogenic amines and ethyl carbamate. Here we explore the potential of the fission yeast Schizosaccharomyces pombe to solve these problems. We characterise an extensive worldwide collection of S. pombe strains according to classic biochemical parameters of oenological interest. We identify three genetically different S. pombe strains that appear suitable for winemaking. These strains compare favourably to standard Saccharomyces cerevisiae winemaking strains, in that they perform effective malic acid deacidification and significantly reduce levels of biogenic amines and ethyl carbamate precursors without the need for any secondary bacterial malolactic fermentation. These findings indicate that the use of certain S. pombe strains could be advantageous for winemaking in regions where malic acid is problematic, and these strains also show superior performance with respect to food safety. PMID:27007548

Extended Plefka expansion for stochastic dynamics

NASA Astrophysics Data System (ADS)

Bravi, B.; Sollich, P.; Opper, M.

2016-05-01

We propose an extension of the Plefka expansion, which is well known for the dynamics of discrete spins, to stochastic differential equations with continuous degrees of freedom and exhibiting generic nonlinearities. The scenario is sufficiently general to allow application to e.g. biochemical networks involved in metabolism and regulation. The main feature of our approach is to constrain in the Plefka expansion not just first moments akin to magnetizations, but also second moments, specifically two-time correlations and responses for each degree of freedom. The end result is an effective equation of motion for each single degree of freedom, where couplings to other variables appear as a self-coupling to the past (i.e. memory term) and a coloured noise. This constitutes a new mean field approximation that should become exact in the thermodynamic limit of a large network, for suitably long-ranged couplings. For the analytically tractable case of linear dynamics we establish this exactness explicitly by appeal to spectral methods of random matrix theory, for Gaussian couplings with arbitrary degree of symmetry.

Why Do Membranes of Some Unhealthy Cells Adopt a Cubic Architecture?

DOE PAGES

Xiao, Qi; Wang, Zhichun; Williams, Dewight; ...

2016-12-05

Nonlamellar lipid arrangements, including cubosomes, appear in unhealthy cells, e.g., when they are subject to stress, starvation, or viral infection. The bioactivity of cubosomes—nanoscale particles exhibiting bicontinuous cubic structures—versus more common vesicles is an unexplored area due to lack of suitable model systems. Here, glycodendrimercubosomes (GDCs)—sugar-presenting cubosomes assembled from Janus glycodendrimers by simple injection into buffer—are proposed as mimics of biological cubic membranes. The bicontinuous cubic GDC architecture has been demonstrated by electron tomography. The stability of these GDCs in buffer enabled studies on lectin-dependent agglutination, revealing significant differences compared with the vesicular glycodendrimersome (GDS) counterpart. In particular, GDCs showedmore » an increased activity toward concanavalin A, as well as an increased sensitivity and selectivity toward two variants of banana lectins, a wild-type and a genetically modified variant, which is not exhibited by GDSs. These results suggest that cells may adapt under unhealthy conditions by undergoing a transformation from lamellar to cubic membranes as a method of defense.« less

Residual stresses investigations in composite samples by speckle interferometry and specimen repositioning

NASA Astrophysics Data System (ADS)

Baldi, Alfonso; Jacquot, Pierre

2003-05-01

Graphite-epoxy laminates are subjected to the "incremental hole-drilling" technique in order to investigate the residual stresses acting within each layer of the composite samples. In-plane speckle interferometry is used to measure the displacement field created by each drilling increment around the hole. Our approach features two particularities (1) we rely on the precise repositioning of the samples in the optical set-up after each new boring step, performed by means of a high precision, numerically controlled milling machine in the workshop; (2) for each increment, we acquire three displacement fields, along the length, the width of the samples, and at 45°, using a single symmetrical double beam illumination and a rotary stage holding the specimens. The experimental protocol is described in detail and the experimental results are presented, including a comparison with strain gages. Speckle interferometry appears as a suitable method to respond to the increasing demand for residual stress determination in composite samples.

Endoscopic fluorescence imaging for early assessment of anastomotic recurrence of Crohn's disease

NASA Astrophysics Data System (ADS)

Mordon, Serge R.; Maunoury, Vincent; Geboes, K.; Klein, Olivier; Desreumaux, P.; Debaert, A.; Colombel, Jean-Frederic

1999-02-01

Crohn's disease is an inflammatory bowel disease of unknown etiology. The mechanism of the initial mucosal alterations is still unclear: ulcerations overlying lymphoid follicles and/or vasculitis have been proposed as the early lesions. We have developed a new and original method combining endoscopy of fluorescence angiography for identifying the early pathological lesions, occurring in the neo-terminal ileum after right ileocolonic resection. The patient population consisted of 10 subjects enrolled in a prospective protocol of endoscopic follow-up at 3 and 12 months after surgery. Fluorescence imaging showed small spots giving a bright fluorescence distributed singly in mucosa which appeared normal in routine endoscopy. Histopathological examination demonstrated that the fluorescence of small spots originated from small, usually superficial, erosive lesions. In several cases, these erosive lesions occurred over lymphoid follicles. Endoscopic fluorescence imaging provides a suitable means of investigating the initial aspect of the Crohn's disease process in displaying some correlative findings between fluorescent aspects and early pathological mucosal alterations.

A priori calculations of the free energy of formation from solution of polymorphic self-assembled monolayers.

PubMed

Reimers, Jeffrey R; Panduwinata, Dwi; Visser, Johan; Chin, Yiing; Tang, Chunguang; Goerigk, Lars; Ford, Michael J; Sintic, Maxine; Sum, Tze-Jing; Coenen, Michiel J J; Hendriksen, Bas L M; Elemans, Johannes A A W; Hush, Noel S; Crossley, Maxwell J

2015-11-10

Modern quantum chemical electronic structure methods typically applied to localized chemical bonding are developed to predict atomic structures and free energies for meso-tetraalkylporphyrin self-assembled monolayer (SAM) polymorph formation from organic solution on highly ordered pyrolytic graphite surfaces. Large polymorph-dependent dispersion-induced substrate-molecule interactions (e.g., -100 kcal mol(-1) to -150 kcal mol(-1) for tetratrisdecylporphyrin) are found to drive SAM formation, opposed nearly completely by large polymorph-dependent dispersion-induced solvent interactions (70-110 kcal mol(-1)) and entropy effects (25-40 kcal mol(-1) at 298 K) favoring dissolution. Dielectric continuum models of the solvent are used, facilitating consideration of many possible SAM polymorphs, along with quantum mechanical/molecular mechanical and dispersion-corrected density functional theory calculations. These predict and interpret newly measured and existing high-resolution scanning tunnelling microscopy images of SAM structure, rationalizing polymorph formation conditions. A wide range of molecular condensed matter properties at room temperature now appear suitable for prediction and analysis using electronic structure calculations.

Think aloud: acute stress and coping strategies during golf performances.

PubMed

Nicholls, Adam R; Polman, Remco C J

2008-07-01

A limitation of the sport psychology coping literature is the amount of time between a stressful episode and the recall of the coping strategies used in the stressful event (Nicholls & Polman, 2007). The purpose of this study was to develop and implement a technique to measure acute stress and coping during performance. Five high-performance adolescent golfers took part in Level 2 verbalization think aloud trials (Ericsson & Simon, 1993), which involved participants verbalizing their thoughts, over six holes of golf. Verbal reports were audio-recorded during each performance, transcribed verbatim, and analyzed using protocol analysis (Ericsson & Simon, 1993). Stressors and coping strategies varied throughout the six holes, which support the proposition that stress and coping is a dynamic process that changes across phases of the same performance (Lazarus, 1999). The results also revealed information regarding the sequential patterning of stress and coping, suggesting that the golfers experienced up to five stressors before reporting a coping strategy. Think aloud appears a suitable method to collect concurrent stress and coping data.

Why Do Membranes of Some Unhealthy Cells Adopt a Cubic Architecture?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiao, Qi; Wang, Zhichun; Williams, Dewight

Nonlamellar lipid arrangements, including cubosomes, appear in unhealthy cells, e.g., when they are subject to stress, starvation, or viral infection. The bioactivity of cubosomes—nanoscale particles exhibiting bicontinuous cubic structures—versus more common vesicles is an unexplored area due to lack of suitable model systems. Here, glycodendrimercubosomes (GDCs)—sugar-presenting cubosomes assembled from Janus glycodendrimers by simple injection into buffer—are proposed as mimics of biological cubic membranes. The bicontinuous cubic GDC architecture has been demonstrated by electron tomography. The stability of these GDCs in buffer enabled studies on lectin-dependent agglutination, revealing significant differences compared with the vesicular glycodendrimersome (GDS) counterpart. In particular, GDCs showedmore » an increased activity toward concanavalin A, as well as an increased sensitivity and selectivity toward two variants of banana lectins, a wild-type and a genetically modified variant, which is not exhibited by GDSs. These results suggest that cells may adapt under unhealthy conditions by undergoing a transformation from lamellar to cubic membranes as a method of defense.« less

Electrospun amplified fiber optics.

PubMed

Morello, Giovanni; Camposeo, Andrea; Moffa, Maria; Pisignano, Dario

2015-03-11

All-optical signal processing is the focus of much research aiming to obtain effective alternatives to existing data transmission platforms. Amplification of light in fiber optics, such as in Erbium-doped fiber amplifiers, is especially important for efficient signal transmission. However, the complex fabrication methods involving high-temperature processes performed in a highly pure environment slow the fabrication process and make amplified components expensive with respect to an ideal, high-throughput, room temperature production. Here, we report on near-infrared polymer fiber amplifiers working over a band of ∼20 nm. The fibers are cheap, spun with a process entirely carried out at room temperature, and shown to have amplified spontaneous emission with good gain coefficients and low levels of optical losses (a few cm(-1)). The amplification process is favored by high fiber quality and low self-absorption. The found performance metrics appear to be suitable for short-distance operations, and the large variety of commercially available doping dyes might allow for effective multiwavelength operations by electrospun amplified fiber optics.

The Age of Rift-Related Basalts in East Antarctica

NASA Astrophysics Data System (ADS)

Leitchenkov, G. L.; Belyatsky, B. V.; Kaminsky, V. D.

2018-01-01

The Lambert Rift, which is a large intracontinental rift zone in East Antarctica, developed over a long period of geological time, beginning from the Late Paleozoic, and its evolution was accompanied by magmatic activity. The latest manifestation of magmatism is eruption of alkaline olivine-leucite basalts on the western side of the Lambert Rift; Rb-Sr dating referred its time to the Middle Eocene, although its genesis remained vague. In order to solve this problem, we found geochronometer minerals in basaltic samples and 68 apatite grains appeared to be suitable for analysis. Their ages and ages of host basalts, determined by the U-Pb local method on the SIMS SHRIMP-II, were significantly different (323 ± 31 Ma) from those assumed earlier. This age corresponds to the earliest stage of crustal extension in East Antarctica and to most of Gondwana. The new data crucially change the ideas about the evolution of Lambert Rift and demonstrate the ambiguity of K-Ar dates of the alkali effusive formed under long-term rifting.

Renormalization of minimally doubled fermions

NASA Astrophysics Data System (ADS)

Capitani, Stefano; Creutz, Michael; Weber, Johannes; Wittig, Hartmut

2010-09-01

We investigate the renormalization properties of minimally doubled fermions, at one loop in perturbation theory. Our study is based on the two particular realizations of Boriçi-Creutz and Karsten-Wilczek. A common feature of both formulations is the breaking of hyper-cubic symmetry, which requires that the lattice actions are supplemented by suitable counterterms. We show that three counterterms are required in each case and determine their coefficients to one loop in perturbation theory. For both actions we compute the vacuum polarization of the gluon. It is shown that no power divergences appear and that all contributions which arise from the breaking of Lorentz symmetry are cancelled by the counterterms. We also derive the conserved vector and axial-vector currents for Karsten-Wilczek fermions. Like in the case of the previously studied Boriçi-Creutz action, one obtains simple expressions, involving only nearest-neighbour sites. We suggest methods how to fix the coefficients of the counterterms non-perturbatively and discuss the implications of our findings for practical simulations.

Transparent lithium-ion batteries

PubMed Central

Yang, Yuan; Jeong, Sangmoo; Hu, Liangbing; Wu, Hui; Lee, Seok Woo; Cui, Yi

2011-01-01

Transparent devices have recently attracted substantial attention. Various applications have been demonstrated, including displays, touch screens, and solar cells; however, transparent batteries, a key component in fully integrated transparent devices, have not yet been reported. As battery electrode materials are not transparent and have to be thick enough to store energy, the traditional approach of using thin films for transparent devices is not suitable. Here we demonstrate a grid-structured electrode to solve this dilemma, which is fabricated by a microfluidics-assisted method. The feature dimension in the electrode is below the resolution limit of human eyes, and, thus, the electrode appears transparent. Moreover, by aligning multiple electrodes together, the amount of energy stored increases readily without sacrificing the transparency. This results in a battery with energy density of 10 Wh/L at a transparency of 60%. The device is also flexible, further broadening their potential applications. The transparent device configuration also allows in situ Raman study of fundamental electrochemical reactions in batteries. PMID:21788483

A new method for placental/cord blood processing in the collection bag. I. Analysis of factors involved in red blood cell removal.

PubMed

Bertolini, F; Battaglia, M; Zibera, C; Baroni, G; Soro, V; Perotti, C; Salvaneschi, L; Robustelli della Cuna, G

1996-10-01

We describe a new procedure for large-scale CB processing in the collection bag, thus minimizing the risk of CB contamination. A solution of 6% hydroxyethyl starch (HES) was added directly to the CB containing bag. After RBC sedimentation at 4 degrees C, the WBC-rich supernatant was collected in a satellite bag and centrifuged. After supernatant removal, the cell pellet was resuspended and the percent recovery of total WBC, CD34+ progenitor cells, CFU-GM and cobblestone area-forming cells (CAFC) evaluated. Results obtained with three different types of CB collection bags (300, 600 and 1000 ml) were analyzed and compared with those of an open system in 50 ml tubes. CB processing procedures in 300 and 1000 ml bags were associated with better WBC, CFU, CD34+ cell and CAFC recovery (83-93%). This novel CB processing procedure appears to be easy, effective and particularly suitable for large-scale banking under GMP conditions.

The Locomotion of Mouse Fibroblasts in Tissue Culture

PubMed Central

Gail, Mitchell H.; Boone, Charles W.

1970-01-01

Time-lapse cinematography was used to investigate the motion of mouse fibroblasts in tissue culture. Observations over successive short time intervals revealed a tendency for the cells to persist in their direction of motion from one 2.5 hr time interval to the next. Over 5.0-hr time intervals, however, the direction of motion appeared random. This fact suggested that D, the diffusion constant of a random walk model, might serve to characterize cellular motility if suitably long observation times were used. We therefore investigated the effect of “persistence” on the pure random walk model, and we found theoretically and confirmed experimentally that the motility of a persisting cell could indeed be characterized by an augmented diffusion constant, D*. A method for determining confidence limits on D* was also developed. Thus a random walk model, modified to comprehend the persistence effect, was found to describe the motion of fibroblasts in tissue culture and to provide a numerical measure of cellular motility. PMID:5531614

Silver nanowires as infrared-active materials for surface-enhanced Raman scattering.

PubMed

Becucci, Maurizio; Bracciali, Monica; Ghini, Giacomo; Lofrumento, Cristiana; Pietraperzia, Giangaetano; Ricci, Marilena; Tognaccini, Lorenzo; Trigari, Silvana; Gellini, Cristina; Feis, Alessandro

2018-05-17

Surface-enhanced Raman scattering (SERS) is increasing in significance as a bioanalytical tool. Novel nanostructured metal substrates are required to improve performances and versatility of SERS spectroscopy. In particular, as biological tissues are relatively transparent in the infrared wavelength range, SERS-active materials suitable for infrared laser excitation are needed. Nanowires appear interesting in this respect as they show a very broad localized surface plasmon resonance band, ranging from near UV to near infrared wavelengths. The SERS activity of silver nanowires has been tested at three wavelengths and a fair enhancement at 1064 and 514 nm has been observed, whereas a very weak enhancement was present when exciting close to the nanowire extinction maximum. These experimentally measured optical properties have been contrasted with finite element method simulations. Furthermore, laser-induced optoacoustic spectroscopy measurements have shown that the extinction at 1064 nm is completely due to scattering. This result has an important implication that no heating occurs when silver nanowires are utilized as SERS-active substrates, thereby preventing possible thermal damage.

Lead paste recycling based on conversion into battery grade oxides. Electrochemical tests and industrial production of new batteries

NASA Astrophysics Data System (ADS)

Fusillo, G.; Rosestolato, D.; Scura, F.; Cattarin, S.; Mattarozzi, L.; Guerriero, P.; Gambirasi, A.; Brianese, N.; Staiti, P.; Guerriero, R.; La Sala, G.

2018-03-01

We present the preparation and characterization of pure lead monoxide obtained through recycling of the lead paste recovered from exhausted lead acid batteries. The recycling is based on a hydrometallurgical procedure reported in a STC Patent, that includes simple chemical operations (desulphurisation, leaching, precipitation, filtration) and a final thermal conversion. Materials obtained by treatment at 600 °C consist predominantly of β-PbO. The electrochemical behaviour of Positive Active Mass (PAM) prepared from different materials (or mixtures) is then investigated and compared. An optimized oxide material, obtained by prolonged (8 h) thermal treatment at 600 °C, consists of pure β-PbO and appears suitable for preparation of battery elements, alone or in mixture with a small fraction (10%-30%) of traditional industrial leady oxide. The resulting battery performances are similar to those obtained from pure leady oxide. In comparison with traditional recycling processes, the proposed method guarantees lower energy consumption, limited environmental impact and reduced operating risk for industry workers.

Laboratory analytical methods for the determination of the hydrocarbon status of soils (a review)

NASA Astrophysics Data System (ADS)

Pikovskii, Yu. I.; Korotkov, L. A.; Smirnova, M. A.; Kovach, R. G.

2017-10-01

Laboratory analytical methods suitable for the determination of the hydrocarbon status of soils (a specific soil characteristic involving information on the total content and qualitative features of soluble (bitumoid) carbonaceous substances and individual hydrocarbons (polycyclic aromatic hydrocarbons, alkanes, etc.) in bitumoid, as well as the composition and content of hydrocarbon gases) have been considered. Among different physicochemical methods of study, attention is focused on the methods suitable for the wide use. Luminescence-bituminological analysis, low-temperature spectrofluorimetry (Shpolskii spectroscopy), infrared (IR) spectroscopy, gas chromatography, chromatography-mass spectrometry, and some other methods have been characterized, as well as sample preparation features. Advantages and limitations of each of these methods are described; their efficiency, instrumental complexity, analysis duration, and accuracy are assessed.

Methods for producing Cu-67 radioisotope with use of a ceramic capsule for medical applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ehst, David A.; Willit, James L.

The present invention provides a method for producing Cu67 radioisotope suitable for use in medical applications. The method comprises irradiating a metallic zinc-68 (Zn68) target within a sealed ceramic capsule with a high energy gamma ray beam. After irradiation, the Cu67 is isolated from the Zn68 by any suitable method (e.g. chemical and or physical separation). In a preferred embodiment, the Cu67 is isolated by sublimation of the zinc in a ceramic sublimation tube to afford a copper residue containing Cu67. The Cu67 can be further purified by chemical means.

Study of Systems Using Inertia Wheels for Precise Attitude Control of a Satellite

NASA Technical Reports Server (NTRS)

White, John S.; Hansen, Q. Marion

1961-01-01

Systems using inertia wheels are evaluated in this report to determine their suitability for precise attitude control of a satellite and to select superior system configurations. Various possible inertia wheel system configurations are first discussed in a general manner. Three of these systems which appear more promising than the others are analyzed in detail, using the Orbiting Astronomical Observatory as an example. The three systems differ from each other only by the method of damping, which is provided by either a rate gyro, an error-rate network, or a tachometer in series with a high-pass filter. An analytical investigation which consists of a generalized linear analysis, a nonlinear analysis using the switching-time method, and an analog computer study shows that all three systems are theoretically capable of producing adequate response and also of maintaining the required pointing accuracy for the Orbiting Astronomical Observatory of plus or minus 0.1 second of arc. Practical considerations and an experimental investigation show, however, that the system which uses an error-rate network to provide damping is superior to the other two systems. The system which uses a rate gyro is shown to be inferior because the threshold level causes a significant amount of limit-cycle operation, and the system which uses a tachometer with a filter is shown to be inferior because a device with the required dynamic range of operation does not appear to be available. The experimental laboratory apparatus used to investigate the dynamic performance of the systems is described, and experimental results are included to show that under laboratory conditions with relatively large extraneous disturbances, a dynamic tracking error of less than plus or minus 0.5 second of arc was obtained.

Can discrete event simulation be of use in modelling major depression?

PubMed Central

Le Lay, Agathe; Despiegel, Nicolas; François, Clément; Duru, Gérard

2006-01-01

Background Depression is among the major contributors to worldwide disease burden and adequate modelling requires a framework designed to depict real world disease progression as well as its economic implications as closely as possible. Objectives In light of the specific characteristics associated with depression (multiple episodes at varying intervals, impact of disease history on course of illness, sociodemographic factors), our aim was to clarify to what extent "Discrete Event Simulation" (DES) models provide methodological benefits in depicting disease evolution. Methods We conducted a comprehensive review of published Markov models in depression and identified potential limits to their methodology. A model based on DES principles was developed to investigate the benefits and drawbacks of this simulation method compared with Markov modelling techniques. Results The major drawback to Markov models is that they may not be suitable to tracking patients' disease history properly, unless the analyst defines multiple health states, which may lead to intractable situations. They are also too rigid to take into consideration multiple patient-specific sociodemographic characteristics in a single model. To do so would also require defining multiple health states which would render the analysis entirely too complex. We show that DES resolve these weaknesses and that its flexibility allow patients with differing attributes to move from one event to another in sequential order while simultaneously taking into account important risk factors such as age, gender, disease history and patients attitude towards treatment, together with any disease-related events (adverse events, suicide attempt etc.). Conclusion DES modelling appears to be an accurate, flexible and comprehensive means of depicting disease progression compared with conventional simulation methodologies. Its use in analysing recurrent and chronic diseases appears particularly useful compared with Markov processes. PMID:17147790

Sensory and rapid instrumental methods as a combined tool for quality control of cooked ham.

PubMed

Barbieri, Sara; Soglia, Francesca; Palagano, Rosa; Tesini, Federica; Bendini, Alessandra; Petracci, Massimiliano; Cavani, Claudio; Gallina Toschi, Tullia

2016-11-01

In this preliminary investigation, different commercial categories of Italian cooked pork hams have been characterized using an integrated approach based on both sensory and fast instrumental measurements. For these purposes, Italian products belonging to different categories (cooked ham, "selected" cooked ham and "high quality" cooked ham) were evaluated by sensory descriptive analysis and by the application of rapid tools such as image analysis by an "electronic eye" and texture analyzer. The panel of trained assessors identified and evaluated 10 sensory descriptors able to define the quality of the products. Statistical analysis highlighted that sensory characteristics related to appearance and texture were the most significant in discriminating samples belonged to the highest (high quality cooked hams) and the lowest (cooked hams) quality of the product whereas the selected cooked hams, showed intermediate characteristics. In particular, high quality samples were characterized, above all, by the highest intensity of pink intensity, typical appearance and cohesiveness, and, at the same time, by the lowest intensity of juiciness; standard cooked ham samples showed the lowest intensity of all visual attributes and the highest value of juiciness, whereas the intermediate category (selected cooked ham) was not discriminated from the other. Also physical-rheological parameters measured by electronic eye and texture analyzer were effective in classifying samples. In particular, the PLS model built with data obtained from the electronic eye showed a satisfactory performance in terms of prediction of the pink intensity and presence of fat attributes evaluated during the sensory visual phase. This study can be considered a first application of this combined approach that could represent a suitable and fast method to verify if the meat product purchased by consumer match its description in terms of compliance with the claimed quality.

[Climatic suitability of citrus in subtropical China].

PubMed

Duan, Hai-Lai; Qian, Huai-Sui; Li, Ming-Xia; Du, Yao-Dong

2010-08-01

By applying the theories of ecological suitability and the methods of fuzzy mathematics, this paper established a climatic suitability model for citrus, calculated and evaluated the climatic suitability and its spatiotemporal differences for citrus production in subtropical China, and analyzed the climatic suitability of citrus at its different growth stages and the mean climatic suitability of citrus in different regions of subtropical China. The results showed that the citrus in subtropical China had a lower climatic suitability and a higher risk at its flower bud differentiation stage, budding stage, and fruit maturity stage, but a higher climatic suitability and a lower risk at other growth stages. Cold damage and summer drought were the key issues affecting the citrus production in subtropical China. The citrus temperature suitability represented a latitudinal zonal pattern, i. e., decreased with increasing latitude; its precipitation suitability was high in the line of "Sheyang-Napo", medium in the southeast of the line, low in the northwest of the line, and non in high mountainous area; while the sunlight suitability was in line with the actual duration of sunshine, namely, higher in high-latitude areas than in low-latitude areas, and higher in high-altitude areas than in plain areas. Limited by temperature factor, the climatic suitability was in accordance with temperature suitability, i. e., south parts had a higher suitability than north parts, basically representing latitudinal zonal pattern. From the analysis of the inter-annual changes of citrus climatic suitability, it could be seen that the citrus climatic suitability in subtropical China was decreasing, and had obvious regional differences, suggesting that climate change could bring about the changes in the regions suitable for citrus production and in the key stages of citrus growth.

The Use of the Visualisation of Multidimensional Data Using PCA to Evaluate Possibilities of the Division of Coal Samples Space Due to their Suitability for Fluidised Gasification

NASA Astrophysics Data System (ADS)

Jamróz, Dariusz; Niedoba, Tomasz; Surowiak, Agnieszka; Tumidajski, Tadeusz

2016-09-01

Methods serving to visualise multidimensional data through the transformation of multidimensional space into two-dimensional space, enable to present the multidimensional data on the computer screen. Thanks to this, qualitative analysis of this data can be performed in the most natural way for humans, through the sense of sight. An example of such a method of multidimensional data visualisation is PCA (principal component analysis) method. This method was used in this work to present and analyse a set of seven-dimensional data (selected seven properties) describing coal samples obtained from Janina and Wieczorek coal mines. Coal from these mines was previously subjected to separation by means of a laboratory ring jig, consisting of ten rings. With 5 layers of both types of coal (with 2 rings each) were obtained in this way. It was decided to check if the method of multidimensional data visualisation enables to divide the space of such divided samples into areas with different suitability for the fluidised gasification process. To that end, the card of technological suitability of coal was used (Sobolewski et al., 2012; 2013), in which key, relevant and additional parameters, having effect on the gasification process, were described. As a result of analyses, it was stated that effective determination of coal samples suitability for the on-surface gasification process in a fluidised reactor is possible. The PCA method enables the visualisation of the optimal subspace containing the set requirements concerning the properties of coals intended for this process.

An iterative and targeted sampling design informed by habitat suitability models for detecting focal plant species over extensive areas.

PubMed

Wang, Ophelia; Zachmann, Luke J; Sesnie, Steven E; Olsson, Aaryn D; Dickson, Brett G

2014-01-01

Prioritizing areas for management of non-native invasive plants is critical, as invasive plants can negatively impact plant community structure. Extensive and multi-jurisdictional inventories are essential to prioritize actions aimed at mitigating the impact of invasions and changes in disturbance regimes. However, previous work devoted little effort to devising sampling methods sufficient to assess the scope of multi-jurisdictional invasion over extensive areas. Here we describe a large-scale sampling design that used species occurrence data, habitat suitability models, and iterative and targeted sampling efforts to sample five species and satisfy two key management objectives: 1) detecting non-native invasive plants across previously unsampled gradients, and 2) characterizing the distribution of non-native invasive plants at landscape to regional scales. Habitat suitability models of five species were based on occurrence records and predictor variables derived from topography, precipitation, and remotely sensed data. We stratified and established field sampling locations according to predicted habitat suitability and phenological, substrate, and logistical constraints. Across previously unvisited areas, we detected at least one of our focal species on 77% of plots. In turn, we used detections from 2011 to improve habitat suitability models and sampling efforts in 2012, as well as additional spatial constraints to increase detections. These modifications resulted in a 96% detection rate at plots. The range of habitat suitability values that identified highly and less suitable habitats and their environmental conditions corresponded to field detections with mixed levels of agreement. Our study demonstrated that an iterative and targeted sampling framework can address sampling bias, reduce time costs, and increase detections. Other studies can extend the sampling framework to develop methods in other ecosystems to provide detection data. The sampling methods implemented here provide a meaningful tool when understanding the potential distribution and habitat of species over multi-jurisdictional and extensive areas is needed for achieving management objectives.

An Iterative and Targeted Sampling Design Informed by Habitat Suitability Models for Detecting Focal Plant Species over Extensive Areas

PubMed Central

Wang, Ophelia; Zachmann, Luke J.; Sesnie, Steven E.; Olsson, Aaryn D.; Dickson, Brett G.

2014-01-01

Prioritizing areas for management of non-native invasive plants is critical, as invasive plants can negatively impact plant community structure. Extensive and multi-jurisdictional inventories are essential to prioritize actions aimed at mitigating the impact of invasions and changes in disturbance regimes. However, previous work devoted little effort to devising sampling methods sufficient to assess the scope of multi-jurisdictional invasion over extensive areas. Here we describe a large-scale sampling design that used species occurrence data, habitat suitability models, and iterative and targeted sampling efforts to sample five species and satisfy two key management objectives: 1) detecting non-native invasive plants across previously unsampled gradients, and 2) characterizing the distribution of non-native invasive plants at landscape to regional scales. Habitat suitability models of five species were based on occurrence records and predictor variables derived from topography, precipitation, and remotely sensed data. We stratified and established field sampling locations according to predicted habitat suitability and phenological, substrate, and logistical constraints. Across previously unvisited areas, we detected at least one of our focal species on 77% of plots. In turn, we used detections from 2011 to improve habitat suitability models and sampling efforts in 2012, as well as additional spatial constraints to increase detections. These modifications resulted in a 96% detection rate at plots. The range of habitat suitability values that identified highly and less suitable habitats and their environmental conditions corresponded to field detections with mixed levels of agreement. Our study demonstrated that an iterative and targeted sampling framework can address sampling bias, reduce time costs, and increase detections. Other studies can extend the sampling framework to develop methods in other ecosystems to provide detection data. The sampling methods implemented here provide a meaningful tool when understanding the potential distribution and habitat of species over multi-jurisdictional and extensive areas is needed for achieving management objectives. PMID:25019621

Biodegradation of Aliphatic-Aromatic Copolyesters by Thermomonospora fusca and Other Thermophilic Compost Isolates

PubMed Central

Kleeberg, Ilona; Hetz, Claudia; Kroppenstedt, Reiner Michael; Müller, Rolf-Joachim; Deckwer, Wolf-Dieter

1998-01-01

Random aliphatic-aromatic copolyesters synthesized from 1,4-butanediol, adipic acid, and terephthalic acid (BTA) have excellent thermal and mechanical properties and are biodegradable by mixed cultures (e.g., in compost). Over 20 BTA-degrading strains were isolated by using compost as a microbial source. Among these microorganisms, thermophilic actinomycetes obviously play an outstanding role and appear to dominate the initial degradation step. Two actinomycete strains exhibited about 20-fold higher BTA degradation rates than usually observed in a common compost test. These isolates were identified as Thermomonospora fusca strains. They appeared to be particularly suitable for establishment of rapid degradation tests and were used in comparative studies on the biodegradation of various polyesters. PMID:9572944

Fluorescent detection of apoptotic cells using a family of zinc coordination complexes with selective affinity for membrane surfaces that are enriched with phosphatidylserine.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, Bradley D.; Lambert, Timothy N.; Lakshmi, C.

2005-03-01

The appearance of phosphatidylserine on the membrane surface of apoptotic cells (Jurkat, CHO, HeLa) is monitored by using a family of bis(Zn{sup 2+}-2,2{prime}-dipicolylamine) coordination compounds with appended fluorescein or biotin groups as reporter elements. The phosphatidylserine affinity group is also conjugated directly to a CdSe/CdS quantum dot to produce a probe suitable for prolonged observation without photobleaching. Apoptosis can be detected under a wide variety of conditions, including variations in temperature, incubation time, and binding media. Binding of each probe appears to be restricted to the cell membrane exterior, because no staining of organelles or internal membranes is observed.

Paradigms, pragmatism and possibilities: mixed-methods research in speech and language therapy.

PubMed

Glogowska, Margaret

2011-01-01

After the decades of the so-called 'paradigm wars' in social science research methodology and the controversy about the relative place and value of quantitative and qualitative research methodologies, 'paradigm peace' appears to have now been declared. This has come about as many researchers have begun to take a 'pragmatic' approach in the selection of research methodology, choosing the methodology best suited to answering the research question rather than conforming to a methodological orthodoxy. With the differences in the philosophical underpinnings of the two traditions set to one side, an increasing awareness, and valuing, of the 'mixed-methods' approach to research is now present in the fields of social, educational and health research. To explore what is meant by mixed-methods research and the ways in which quantitative and qualitative methodologies and methods can be combined and integrated, particularly in the broad field of health services research and the narrower one of speech and language therapy. The paper discusses the ways in which methodological approaches have already been combined and integrated in health services research and speech and language therapy, highlighting the suitability of mixed-methods research for answering the typically multifaceted questions arising from the provision of complex interventions. The challenges of combining and integrating quantitative and qualitative methods and the barriers to the adoption of mixed-methods approaches are also considered. The questions about healthcare, as it is being provided in the 21st century, calls for a range of methodological approaches. This is particularly the case for human communication and its disorders, where mixed-methods research offers a wealth of possibilities. In turn, speech and language therapy research should be able to contribute substantively to the future development of mixed-methods research. © 2010 Royal College of Speech & Language Therapists.

Reaction monitoring using hyperpolarized NMR with scaling of heteronuclear couplings by optimal tracking.

PubMed

Zhang, Guannan; Schilling, Franz; Glaser, Steffen J; Hilty, Christian

2016-11-01

Off-resonance decoupling using the method of Scaling of Heteronuclear Couplings by Optimal Tracking (SHOT) enables determination of heteronuclear correlations of chemical shifts in single scan NMR spectra. Through modulation of J-coupling evolution by shaped radio frequency pulses, off resonance decoupling using SHOT pulses causes a user-defined dependence of the observed J-splitting, such as the splitting of 13 C peaks, on the chemical shift offset of coupled nuclei, such as 1 H. Because a decoupling experiment requires only a single scan, this method is suitable for characterizing on-going chemical reactions using hyperpolarization by dissolution dynamic nuclear polarization (D-DNP). We demonstrate the calculation of [ 13 C, 1 H] chemical shift correlations of the carbanionic active sites from hyperpolarized styrene polymerized using sodium naphthalene as an initiator. While off resonance decoupling by SHOT pulses does not enhance the resolution in the same way as a 2D NMR spectrum would, the ability to obtain the correlations in single scans makes this method ideal for determination of chemical shifts in on-going reactions on the second time scale. In addition, we present a novel SHOT pulse that allows to scale J-splittings 50% larger than the respective J-coupling constant. This feature can be used to enhance the resolution of the indirectly detected chemical shift and reduce peak overlap, as demonstrated in a model reaction between p-anisaldehyde and isobutylamine. For both pulses, the accuracy is evaluated under changing signal-to-noise ratios (SNR) of the peaks from reactants and reaction products, with an overall standard deviation of chemical shift differences compared to reference spectra of 0.02ppm when measured on a 400MHz NMR spectrometer. Notably, the appearance of decoupling side-bands, which scale with peak intensity, appears to be of secondary importance. Copyright © 2016 Elsevier Inc. All rights reserved.

A fuel-efficient cruise performance model for general aviation piston engine airplanes. Ph.D. Thesis. Final Report

NASA Technical Reports Server (NTRS)

Parkinson, R. C. H.

1983-01-01

A fuel-efficient cruise performance model which facilitates maximizing the specific range of General Aviation airplanes powered by spark-ignition piston engines and propellers is presented. Airplanes of fixed design only are considered. The uses and limitations of typical Pilot Operating Handbook cruise performance data, for constructing cruise performance models suitable for maximizing specific range, are first examined. These data are found to be inadequate for constructing such models. A new model of General Aviation piston-prop airplane cruise performance is then developed. This model consists of two subsystem models: the airframe-propeller-atmosphere subsystem model; and the engine-atmosphere subsystem model. The new model facilitates maximizing specific range; and by virtue of its implicity and low volume data storge requirements, appears suitable for airborne microprocessor implementation.

Nonlinear optimal control for the synchronization of chaotic and hyperchaotic finance systems

NASA Astrophysics Data System (ADS)

Rigatos, G.; Siano, P.; Loia, V.; Ademi, S.; Ghosh, T.

2017-11-01

It is possible to make specific finance systems get synchronized to other finance systems exhibiting chaotic and hyperchaotic dynamics, by applying nonlinear optimal (H-infinity) control. This signifies that chaotic behavior can be generated in finance systems by exerting a suitable control input. Actually, a lead financial system is considered which exhibits inherently chaotic dynamics. Moreover, a follower finance system is introduced having parameters in its model that inherently prohibit the appearance of chaotic dynamics. Through the application of a suitable nonlinear optimal (H-infinity) control input it is proven that the follower finance system can replicate the chaotic dynamics of the lead finance system. By applying Lyapunov analysis it is proven that asymptotically the follower finance system gets synchronized with the lead system and that the tracking error between the state variables of the two systems vanishes.

Assessing the impacts of water abstractions on river ecosystem services: an eco-hydraulic modelling approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carolli, Mauro, E-mail: mauro.carolli@unitn.it; Geneletti, Davide, E-mail: davide.geneletti@unitn.it; Zolezzi, Guido, E-mail: guido.zolezzi@unitn.it

The provision of important river ecosystem services (ES) is dependent on the flow regime. This requires methods to assess the impacts on ES caused by interventions on rivers that affect flow regime, such as water abstractions. This study proposes a method to i) quantify the provision of a set of river ES, ii) simulate the effects of water abstraction alternatives that differ in location and abstracted flow, and iii) assess the impact of water abstraction alternatives on the selected ES. The method is based on river modelling science, and integrates spatially distributed hydrological, hydraulic and habitat models at different spatialmore » and temporal scales. The method is applied to the hydropeaked upper Noce River (Northern Italy), which is regulated by hydropower operations. We selected locally relevant river ES: habitat suitability for the adult marble trout, white-water rafting suitability, hydroelectricity production from run-of-river (RoR) plants. Our results quantify the seasonality of river ES response variables and their intrinsic non-linearity, which explains why the same abstracted flow can produce different effects on trout habitat and rafting suitability depending on the morphology of the abstracted reach. An economic valuation of the examined river ES suggests that incomes from RoR hydropower plants are of comparable magnitude to touristic revenue losses related to the decrease in rafting suitability.« less

Geospatial distribution modeling and determining suitability of groundwater quality for irrigation purpose using geospatial methods and water quality index (WQI) in Northern Ethiopia

NASA Astrophysics Data System (ADS)

Gidey, Amanuel

2018-06-01

Determining suitability and vulnerability of groundwater quality for irrigation use is a key alarm and first aid for careful management of groundwater resources to diminish the impacts on irrigation. This study was conducted to determine the overall suitability of groundwater quality for irrigation use and to generate their spatial distribution maps in Elala catchment, Northern Ethiopia. Thirty-nine groundwater samples were collected to analyze and map the water quality variables. Atomic absorption spectrophotometer, ultraviolet spectrophotometer, titration and calculation methods were used for laboratory groundwater quality analysis. Arc GIS, geospatial analysis tools, semivariogram model types and interpolation methods were used to generate geospatial distribution maps. Twelve and eight water quality variables were used to produce weighted overlay and irrigation water quality index models, respectively. Root-mean-square error, mean square error, absolute square error, mean error, root-mean-square standardized error, measured values versus predicted values were used for cross-validation. The overall weighted overlay model result showed that 146 km2 areas are highly suitable, 135 km2 moderately suitable and 60 km2 area unsuitable for irrigation use. The result of irrigation water quality index confirms 10.26% with no restriction, 23.08% with low restriction, 20.51% with moderate restriction, 15.38% with high restriction and 30.76% with the severe restriction for irrigation use. GIS and irrigation water quality index are better methods for irrigation water resources management to achieve a full yield irrigation production to improve food security and to sustain it for a long period, to avoid the possibility of increasing environmental problems for the future generation.

Application of GIS Technology for Town Planning Tasks Solving

NASA Astrophysics Data System (ADS)

Kiyashko, G. A.

2017-11-01

For developing territories, one of the most actual town-planning tasks is to find out the suitable sites for building projects. The geographic information system (GIS) allows one to model complex spatial processes and can provide necessary effective tools to solve these tasks. We propose several GIS analysis models which can define suitable settlement allocations and select appropriate parcels for construction objects. We implement our models in the ArcGIS Desktop package and verify by application to the existing objects in Primorsky Region (Primorye Territory). These suitability models use several variations of the analysis method combinations and include various ways to resolve the suitability task using vector data and a raster data set. The suitability models created in this study can be combined, and one model can be integrated into another as its part. Our models can be updated by other suitability models for further detailed planning.

Lock Culvert Valves; Hydraulic Design Considerations

DTIC Science & Technology

2011-06-01

gate.” Musical note shape seals are also not suitable as sill seals although they appear to be in use. Lewin (1995) also warns that particular...of the tailwater rather than the high water surface maintained with a reverse tainter valve. Air entrainment through the valve well, which would...the valve. The air vent is located such that the air drawn into the culvert is entrained in the form of very small bubbles, avoiding large air pockets

Some Effects of Compressibility on the Flow Through Fans and Turbines

DTIC Science & Technology

1945-08-01

conditions, or the velocity diagram, for the cascade of airfoils representing a fan or a turbine - blade arrangement (fig. 1). The conservation laws...Compressibility on the Flow Through Fans and Turbines AUTHOR(S); Perl. W.j Epstein, H.T. ORIGINATING AGENCY: Aircraft Engine Research Lab., Cleveland, O... turbine blading . It appears, however, that use of a suitable polytropic exponent n?^7 allows direct application in many cases.) Substitution of

AMINE EXTRACTION OF PLUTONIUM FROM NITRIC ACID SOLUTIONS LOADING AND STRIPPING EXPERIMENTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, A.S.

1961-01-19

Information is presented on a suitable amine processing system for plutonium nitrate. Experiments with concentrated plutonium nitrate solutions show that trilaurylamine (TLA) - xylene solvent systems did not form a second organic phase. Experiments are also reported with tri-noctylamine (TnOA)-xylene and TLA-Amsco - octyl alcohol. Two organic phases appear in both these systems at high plutonium nitrate concentrations. Data are tabulated from loading and stripping experiments. (J.R.D.)

A fast and accurate method to predict 2D and 3D aerodynamic boundary layer flows

NASA Astrophysics Data System (ADS)

Bijleveld, H. A.; Veldman, A. E. P.

2014-12-01

A quasi-simultaneous interaction method is applied to predict 2D and 3D aerodynamic flows. This method is suitable for offshore wind turbine design software as it is a very accurate and computationally reasonably cheap method. This study shows the results for a NACA 0012 airfoil. The two applied solvers converge to the experimental values when the grid is refined. We also show that in separation the eigenvalues remain positive thus avoiding the Goldstein singularity at separation. In 3D we show a flow over a dent in which separation occurs. A rotating flat plat is used to show the applicability of the method for rotating flows. The shown capabilities of the method indicate that the quasi-simultaneous interaction method is suitable for design methods for offshore wind turbine blades.

Harmonic reduction of Direct Torque Control of six-phase induction motor.

PubMed

Taheri, A

2016-07-01

In this paper, a new switching method in Direct Torque Control (DTC) of a six-phase induction machine for reduction of current harmonics is introduced. Selecting a suitable vector in each sampling period is an ordinal method in the ST-DTC drive of a six-phase induction machine. The six-phase induction machine has 64 voltage vectors and divided further into four groups. In the proposed DTC method, the suitable voltage vectors are selected from two vector groups. By a suitable selection of two vectors in each sampling period, the harmonic amplitude is decreased more, in and various comparison to that of the ST-DTC drive. The harmonics loss is greater reduced, while the electromechanical energy is decreased with switching loss showing a little increase. Spectrum analysis of the phase current in the standard and new switching table DTC of the six-phase induction machine and determination for the amplitude of each harmonics is proposed in this paper. The proposed method has a less sampling time in comparison to the ordinary method. The Harmonic analyses of the current in the low and high speed shows the performance of the presented method. The simplicity of the proposed method and its implementation without any extra hardware is other advantages of the proposed method. The simulation and experimental results show the preference of the proposed method. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

Development and evaluation of event-specific quantitative PCR method for genetically modified soybean A2704-12.

PubMed

Takabatake, Reona; Akiyama, Hiroshi; Sakata, Kozue; Onishi, Mari; Koiwa, Tomohiro; Futo, Satoshi; Minegishi, Yasutaka; Teshima, Reiko; Mano, Junichi; Furui, Satoshi; Kitta, Kazumi

2011-01-01

A novel real-time PCR-based analytical method was developed for the event-specific quantification of a genetically modified (GM) soybean event; A2704-12. During the plant transformation, DNA fragments derived from pUC19 plasmid were integrated in A2704-12, and the region was found to be A2704-12 specific. The pUC19-derived DNA sequences were used as primers for the specific detection of A2704-12. We first tried to construct a standard plasmid for A2704-12 quantification using pUC19. However, non-specific signals appeared with both qualitative and quantitative PCR analyses using the specific primers with pUC19 as a template, and we then constructed a plasmid using pBR322. The conversion factor (C(f)), which is required to calculate the amount of the genetically modified organism (GMO), was experimentally determined with two real-time PCR instruments, the Applied Biosystems 7900HT and the Applied Biosystems 7500. The determined C(f) values were both 0.98. The quantitative method was evaluated by means of blind tests in multi-laboratory trials using the two real-time PCR instruments. The limit of quantitation for the method was estimated to be 0.1%. The trueness and precision were evaluated as the bias and reproducibility of relative standard deviation (RSD(R)), and the determined bias and RSD(R) values for the method were each less than 20%. These results suggest that the developed method would be suitable for practical analyses for the detection and quantification of A2704-12.

Brand appearances in contemporary cinema films and contribution to global marketing of cigarettes.

PubMed

Sargent, J D; Tickle, J J; Beach, M L; Dalton, M A; Ahrens, M B; Heatherton, T F

2001-01-06

The appearance of a cigarette brand in a cinema film gives the brand a certain distinction through its association with the characters and general tone of the film. Through the worldwide distribution of films, brands are promoted globally. We assessed the tobacco-brand appearances in a 10-year sample of contemporary films. We viewed the contents of the top 25 US box-office films for each year of release, from 1988 to 1997 (250 films in total). We compared the prevalence of brand appearances for films produced before a voluntary ban on paid product placement by the tobacco industry (1988-90) with films produced after the ban (1991-97). Tobacco-brand appearance was defined as the screen appearance of a brand name, logo, or identifiable trademark on products or product packaging, billboards, store-front advertising, or tobacco promotional items. We defined actor endorsement of a brand as the display of a brand while being handled or used by an actor. More than 85% of the films contained tobacco use. Tobacco brands appeared in 70 (28%) films. Brand appearances were as common in films suitable for adolescent audiences as they were in films for adult audiences (32 vs 35%), and were also present in 20% of those rated for children. Prevalence of brand appearance did not change overall in relation to the ban. However, there was a striking increase in the type of brand appearance depicted, with actor endorsement increasing from 1% of films before the ban to 11% after. Four US cigarette brands accounted for 80% of brand appearances. Revenues outside the USA accounted for 49% of total revenues for these films, indicating a large international audience. Tobacco-brand appearances are common in films and are becoming increasingly endorsed by actors. The most highly advertised US cigarette brands account for most brand appearances, which suggests an advertising motive to this practice.

Survey of engineering computational methods and experimental programs for estimating supersonic missile aerodynamic characteristics

NASA Technical Reports Server (NTRS)

Sawyer, W. C.; Allen, J. M.; Hernandez, G.; Dillenius, M. F. E.; Hemsch, M. J.

1982-01-01

This paper presents a survey of engineering computational methods and experimental programs used for estimating the aerodynamic characteristics of missile configurations. Emphasis is placed on those methods which are suitable for preliminary design of conventional and advanced concepts. An analysis of the technical approaches of the various methods is made in order to assess their suitability to estimate longitudinal and/or lateral-directional characteristics for different classes of missile configurations. Some comparisons between the predicted characteristics and experimental data are presented. These comparisons are made for a large variation in flow conditions and model attitude parameters. The paper also presents known experimental research programs developed for the specific purpose of validating analytical methods and extending the capability of data-base programs.

Selection of suitable NDT methods for building inspection

NASA Astrophysics Data System (ADS)

Pauzi Ismail, Mohamad

2017-11-01

Construction of modern structures requires good quality concrete with adequate strength and durability. Several accidents occurred in the civil constructions and were reported in the media. Such accidents were due to poor workmanship and lack of systematic monitoring during the constructions. In addition, water leaking and cracking in residential houses was commonly reported too. Based on these facts, monitoring the quality of concrete in structures is becoming more and more important subject. This paper describes major Non-destructive Testing (NDT) methods for evaluating structural integrity of concrete building. Some interesting findings during actual NDT inspections on site are presented. The NDT methods used are explained, compared and discussed. The suitable methods are suggested as minimum NDT methods to cover parameters required in the inspection.