Steam versus hot-water scalding in reducing bacterial loads on the skin of commercially processed poultry.

PubMed

Patrick, T E; Goodwin, T L; Collins, J A; Wyche, R C; Love, B E

1972-04-01

A comparison of two types of scalders was conducted to determine their effectiveness in reducing bacterial contamination of poultry carcasses. A conventional hot-water scalder and a prototype model of a steam scalder were tested under commercial conditions. Total plate counts from steam-scalded birds were significantly lower than the counts of water-scalded birds immediately after scalding and again after picking. No differences in the two methods could be found after chilling. Coliform counts from steam-scalded birds were significantly lower than the counts from water-scalded birds immediately after scalding. No significant differences in coliform counts were detected when the two scald methods were compared after defeathering and chilling.

TH-E-17A-07: Improved Cine Four-Dimensional Computed Tomography (4D CT) Acquisition and Processing Method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castillo, S; Castillo, R; Castillo, E

2014-06-15

Purpose: Artifacts arising from the 4D CT acquisition and post-processing methods add systematic uncertainty to the treatment planning process. We propose an alternate cine 4D CT acquisition and post-processing method to consistently reduce artifacts, and explore patient parameters indicative of image quality. Methods: In an IRB-approved protocol, 18 patients with primary thoracic malignancies received a standard cine 4D CT acquisition followed by an oversampling 4D CT that doubled the number of images acquired. A second cohort of 10 patients received the clinical 4D CT plus 3 oversampling scans for intra-fraction reproducibility. The clinical acquisitions were processed by the standard phasemore » sorting method. The oversampling acquisitions were processed using Dijkstras algorithm to optimize an artifact metric over available image data. Image quality was evaluated with a one-way mixed ANOVA model using a correlation-based artifact metric calculated from the final 4D CT image sets. Spearman correlations and a linear mixed model tested the association between breathing parameters, patient characteristics, and image quality. Results: The oversampling 4D CT scans reduced artifact presence significantly by 27% and 28%, for the first cohort and second cohort respectively. From cohort 2, the inter-replicate deviation for the oversampling method was within approximately 13% of the cross scan average at the 0.05 significance level. Artifact presence for both clinical and oversampling methods was significantly correlated with breathing period (ρ=0.407, p-value<0.032 clinical, ρ=0.296, p-value<0.041 oversampling). Artifact presence in the oversampling method was significantly correlated with amount of data acquired, (ρ=-0.335, p-value<0.02) indicating decreased artifact presence with increased breathing cycles per scan location. Conclusion: The 4D CT oversampling acquisition with optimized sorting reduced artifact presence significantly and reproducibly compared to the phase-sorted clinical acquisition.« less

Joint histogram-based cost aggregation for stereo matching.

PubMed

Min, Dongbo; Lu, Jiangbo; Do, Minh N

2013-10-01

This paper presents a novel method for performing efficient cost aggregation in stereo matching. The cost aggregation problem is reformulated from the perspective of a histogram, giving us the potential to reduce the complexity of the cost aggregation in stereo matching significantly. Differently from previous methods which have tried to reduce the complexity in terms of the size of an image and a matching window, our approach focuses on reducing the computational redundancy that exists among the search range, caused by a repeated filtering for all the hypotheses. Moreover, we also reduce the complexity of the window-based filtering through an efficient sampling scheme inside the matching window. The tradeoff between accuracy and complexity is extensively investigated by varying the parameters used in the proposed method. Experimental results show that the proposed method provides high-quality disparity maps with low complexity and outperforms existing local methods. This paper also provides new insights into complexity-constrained stereo-matching algorithm design.

Analysis of different thermal processing methods of foodstuffs to optimize protein, calcium, and phosphorus content for dialysis patients.

PubMed

Vrdoljak, Ivica; Panjkota Krbavčić, Ines; Bituh, Martina; Vrdoljak, Tea; Dujmić, Zoran

2015-05-01

To analyze how different thermal processing methods affect the protein, calcium, and phosphorus content of hospital food served to dialysis patients and to generate recommendations for preparing menus that optimize nutritional content while minimizing the risk of hyperphosphatemia. Standard Official Methods of Analysis (AOAC) methods were used to determine dry matter, protein, calcium, and phosphorus content in potatoes, fresh and frozen carrots, frozen green beans, chicken, beef and pork, frozen hake, pasta, and rice. These levels were determined both before and after boiling in water, steaming, stewing in oil or water, or roasting. Most of the thermal processing methods did not significantly reduce protein content. Boiling increased calcium content in all foodstuffs because of calcium absorption from the hard water. In contrast, stewing in oil containing a small amount of water decreased the calcium content of vegetables by 8% to 35% and of chicken meat by 12% to 40% on a dry weight basis. Some types of thermal processing significantly reduced the phosphorus content of the various foodstuffs, with levels decreasing by 27% to 43% for fresh and frozen vegetables, 10% to 49% for meat, 7% for pasta, and 22.8% for rice on a dry weight basis. On the basis of these results, we modified the thermal processing methods used to prepare a standard hospital menu for dialysis patients. Foodstuffs prepared according to the optimized menu were similar in protein content, higher in calcium, and significantly lower in phosphorus than foodstuffs prepared according to the standard menu. Boiling in water and stewing in oil containing some water significantly reduced phosphorus content without affecting protein content. Soaking meat in cold water for 1 h before thermal processing reduced phosphorus content even more. These results may help optimize the design of menus for dialysis patients. Copyright © 2015 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

Attitudes of New Parents towards Child and Spouse with Lamaze or Non-Lamaze Methods of Childbirth.

ERIC Educational Resources Information Center

McClure, Robert F.; Brewer, R. Thomas

1980-01-01

Lamaze childbirth training was found to have no significant effects on attitudes towards spouse or child. It did have a significant anxiety-reducing effect with respect to childbirth. Parents using the Lamaze method had a more positive attitude about having a baby. (Author/CS)

Multiclass Reduced-Set Support Vector Machines

NASA Technical Reports Server (NTRS)

Tang, Benyang; Mazzoni, Dominic

2006-01-01

There are well-established methods for reducing the number of support vectors in a trained binary support vector machine, often with minimal impact on accuracy. We show how reduced-set methods can be applied to multiclass SVMs made up of several binary SVMs, with significantly better results than reducing each binary SVM independently. Our approach is based on Burges' approach that constructs each reduced-set vector as the pre-image of a vector in kernel space, but we extend this by recomputing the SVM weights and bias optimally using the original SVM objective function. This leads to greater accuracy for a binary reduced-set SVM, and also allows vectors to be 'shared' between multiple binary SVMs for greater multiclass accuracy with fewer reduced-set vectors. We also propose computing pre-images using differential evolution, which we have found to be more robust than gradient descent alone. We show experimental results on a variety of problems and find that this new approach is consistently better than previous multiclass reduced-set methods, sometimes with a dramatic difference.

A New Method for Control of the Efficiency of Gear Reducers

NASA Astrophysics Data System (ADS)

E Kozlov, K.; Egorov, A. V.; Belogusev, V. N.

2017-04-01

This article proposes a new method to control the energy efficiency of gear reducers. The method allows evaluating the friction losses in a drive motor, drive motor bearing assemblies, and toothing both at the stage of control of the finished product and in the course of its operation, maintenance, and repair. The proposed method, unlike currently used methods for control of the efficiency of gear reducers, allows determining the friction losses without the use of strain measurement, which requires calibration of tensometric sensors and expensive equipment. The method is based on the idea of invariability of mechanical characteristics of the induction motor at constant voltage, resistance of windings, and mains frequency, regardless of the driven inertia mass. This paper presents experimental results which verify the theoretical predictions. The proposed method can be implemented in the procedure of acceptance test at the companies that manufacture gear reducers, thereby assess their effectiveness and the level of degradation processes that significantly affect the service life of the research object. The method can be implemented both with universal and with specialized hardware and software complexes. At that, both an increment of the inertia moment and acceleration time of a gear reducer may serve as a performance criterion.

Simple methods to reduce patient exposure during scoliosis radiography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butler, P.F.; Thomas, A.W.; Thompson, W.E.

1986-05-01

Radiation exposure to the breasts of adolescent females can be reduced significantly through the use of one or all of the following methods: fast, rare-earth screen-film combinations; specially designed compensating filters; and breast shielding. The importance of exposure reduction during scoliosis radiography as well as further details on the above described methods are discussed. In addition, the early results of a Center for Devices and Radiological Health study, which recorded exposure and technique data for scoliosis radiography, is presented.

Contraceptive method and pregnancy incidence among African women in HIV-1 serodiscordant partnerships

PubMed Central

NGURE, Kenneth; HEFFRON, Renee; MUGO, Nelly R.; CELUM, Connie; COHEN, Craig R.; ODOYO, Josephine; REES, Helen; KIARIE, James N.; WERE, Edwin; BAETEN, Jared M.

2014-01-01

Background Effective contraception reduces unintended pregnancies and is a central strategy to reduce vertical HIV-1 transmission for HIV-1 infected women. Methods Among 2269 HIV-1 seropositive and 1085 seronegative women from 7 African countries who were members of HIV-1 serodiscordant heterosexual partnerships and who were participating in an HIV-1 prevention clinical trial, we assessed pregnancy incidence for women using various contraceptive methods using multivariate Andersen-Gill analysis. Results Compared with women using no contraceptive method, pregnancy incidence was significantly reduced among HIV-1 seropositive and seronegative women using injectable contraception (adjusted hazard ratio (aHR) 0.24, p=0.001 and aHR 0.25, p<0.001, respectively). Oral contraceptives significantly reduced pregnancy risk only among HIV-1 seropositive women (aHR 0.51, p=0.004) but not seronegative women (aHR 0.64, p=0.3), and, for both seropositive and seronegative women, oral contraceptive pill users were more likely to become pregnant than injectable contraceptive users (aHR 2.22, p=0.01 for HIV-1 seropositive women and aHR 2.65, p=0.09 for HIV-1 seronegative women). Condoms, when reported as being used as the primary contraceptive method, marginally reduced pregnancy incidence (aHR 0.85, p=0.1 for seropositive women and aHR 0.67, p=0.02 for seronegative women). There were no pregnancies among women using intrauterine devices, implantable methods or who had undergone surgical sterilization, although these methods were used relatively infrequently. Conclusions Family planning programs and HIV-1 prevention trials need innovative ways to motivate uptake and sustained use of longer acting, less user-dependent contraception for women who do not desire pregnancy. PMID:22156966

Steam Versus Hot-Water Scalding in Reducing Bacterial Loads on the Skin of Commercially Processed Poultry

PubMed Central

Patrick, Thomas E.; Goodwin, T. L.; Collins, J. A.; Wyche, R. C.; Love, B. E.

1972-01-01

A comparison of two types of scalders was conducted to determine their effectiveness in reducing bacterial contamination of poultry carcasses. A conventional hot-water scalder and a prototype model of a steam scalder were tested under commercial conditions. Total plate counts from steam-scalded birds were significantly lower than the counts of water-scalded birds immediately after scalding and again after picking. No differences in the two methods could be found after chilling. Coliform counts from steam-scalded birds were significantly lower than the counts from water-scalded birds immediately after scalding. No significant differences in coliform counts were detected when the two scald methods were compared after defeathering and chilling. PMID:4553146

Exact model reduction of combinatorial reaction networks

PubMed Central

Conzelmann, Holger; Fey, Dirk; Gilles, Ernst D

2008-01-01

Background Receptors and scaffold proteins usually possess a high number of distinct binding domains inducing the formation of large multiprotein signaling complexes. Due to combinatorial reasons the number of distinguishable species grows exponentially with the number of binding domains and can easily reach several millions. Even by including only a limited number of components and binding domains the resulting models are very large and hardly manageable. A novel model reduction technique allows the significant reduction and modularization of these models. Results We introduce methods that extend and complete the already introduced approach. For instance, we provide techniques to handle the formation of multi-scaffold complexes as well as receptor dimerization. Furthermore, we discuss a new modeling approach that allows the direct generation of exactly reduced model structures. The developed methods are used to reduce a model of EGF and insulin receptor crosstalk comprising 5,182 ordinary differential equations (ODEs) to a model with 87 ODEs. Conclusion The methods, presented in this contribution, significantly enhance the available methods to exactly reduce models of combinatorial reaction networks. PMID:18755034

Method and apparatus for optoacoustic spectroscopy

DOEpatents

Amer, Nabil M.

1979-01-01

A method and apparatus that significantly increases the sensitivity and flexibility of laser optoacoustic spectroscopy, with reduced size. With the method, it no longer is necessary to limit the use of laser optoacoustic spectroscopy to species whose absorption must match available laser radiation. Instead, "doping" with a relatively small amount of an optically absorbing gas yields optoacoustic signatures of nonabsorbing materials (gases, liquids, solids, and aerosols), thus significantly increasing the sensitivity and flexibility of optoacoustic spectroscopy. Several applications of this method are demonstated and/or suggested.

Adaptation of hidden Markov models for recognizing speech of reduced frame rate.

PubMed

Lee, Lee-Min; Jean, Fu-Rong

2013-12-01

The frame rate of the observation sequence in distributed speech recognition applications may be reduced to suit a resource-limited front-end device. In order to use models trained using full-frame-rate data in the recognition of reduced frame-rate (RFR) data, we propose a method for adapting the transition probabilities of hidden Markov models (HMMs) to match the frame rate of the observation. Experiments on the recognition of clean and noisy connected digits are conducted to evaluate the proposed method. Experimental results show that the proposed method can effectively compensate for the frame-rate mismatch between the training and the test data. Using our adapted model to recognize the RFR speech data, one can significantly reduce the computation time and achieve the same level of accuracy as that of a method, which restores the frame rate using data interpolation.

Advanced Guidance and Control Project for Reusable Launch Vehicles

NASA Technical Reports Server (NTRS)

Hanson, John M.

2000-01-01

The goals of this project are to significantly reduce the time and cost associated with guidance and control design for reusable launch vehicles, and to increase their safety and reliability. Success will lead to reduced cycle times during vehicle design and to reduced costs associated with flying to new orbits, with new payloads, and with modified vehicles. Success will also lead to more robustness to unforeseen circumstances in flight thereby enhancing safety and reducing risk. There are many guidance and control methods available that hold some promise for improvement in the desired areas. Investigators are developing a representative set of independent guidance and control methods for this project. These methods are being incorporated into a high-fidelity off is being conducted across a broad range of flight requirements. The guidance and control methods that perform the best will have demonstrated the desired qualities.

Bubble Entropy: An Entropy Almost Free of Parameters.

PubMed

Manis, George; Aktaruzzaman, Md; Sassi, Roberto

2017-11-01

Objective : A critical point in any definition of entropy is the selection of the parameters employed to obtain an estimate in practice. We propose a new definition of entropy aiming to reduce the significance of this selection. Methods: We call the new definition Bubble Entropy . Bubble Entropy is based on permutation entropy, where the vectors in the embedding space are ranked. We use the bubble sort algorithm for the ordering procedure and count instead the number of swaps performed for each vector. Doing so, we create a more coarse-grained distribution and then compute the entropy of this distribution. Results: Experimental results with both real and synthetic HRV signals showed that bubble entropy presents remarkable stability and exhibits increased descriptive and discriminating power compared to all other definitions, including the most popular ones. Conclusion: The definition proposed is almost free of parameters. The most common ones are the scale factor r and the embedding dimension m . In our definition, the scale factor is totally eliminated and the importance of m is significantly reduced. The proposed method presents increased stability and discriminating power. Significance: After the extensive use of some entropy measures in physiological signals, typical values for their parameters have been suggested, or at least, widely used. However, the parameters are still there, application and dataset dependent, influencing the computed value and affecting the descriptive power. Reducing their significance or eliminating them alleviates the problem, decoupling the method from the data and the application, and eliminating subjective factors. Objective : A critical point in any definition of entropy is the selection of the parameters employed to obtain an estimate in practice. We propose a new definition of entropy aiming to reduce the significance of this selection. Methods: We call the new definition Bubble Entropy . Bubble Entropy is based on permutation entropy, where the vectors in the embedding space are ranked. We use the bubble sort algorithm for the ordering procedure and count instead the number of swaps performed for each vector. Doing so, we create a more coarse-grained distribution and then compute the entropy of this distribution. Results: Experimental results with both real and synthetic HRV signals showed that bubble entropy presents remarkable stability and exhibits increased descriptive and discriminating power compared to all other definitions, including the most popular ones. Conclusion: The definition proposed is almost free of parameters. The most common ones are the scale factor r and the embedding dimension m . In our definition, the scale factor is totally eliminated and the importance of m is significantly reduced. The proposed method presents increased stability and discriminating power. Significance: After the extensive use of some entropy measures in physiological signals, typical values for their parameters have been suggested, or at least, widely used. However, the parameters are still there, application and dataset dependent, influencing the computed value and affecting the descriptive power. Reducing their significance or eliminating them alleviates the problem, decoupling the method from the data and the application, and eliminating subjective factors.

Study of Dimple Effect on the Friction Characteristics of a Journal Bearing using Taguchi Method

NASA Astrophysics Data System (ADS)

Murthy, A. Amar; Raghunandana, Dr.

2018-02-01

The effect of producing dimples using chemically etched techniques or by machining process on the surface of a journal bearing bushing to reduce the friction using Taguchi method is investigated. The data used in the present analysis is based on the results obtained by the series of experiments conducted to study the dimples effect on the Stribeck curve. It is statistically proved that producing dimples on the bushing surface of a journal bearing has significant effect on the friction coefficient when used with light oils. Also it is seen that there is an interaction effect between speeds-load and load-dimples. Hence the interaction effect, which are usually neglected should be considered during actual experiments that significantly contributes in reducing the friction in mixed lubrication regime. The experiments, if were conducted after Taguchi method, then the number of experiments would have been reduced to half of the actual set of experiments that were essentially conducted.

Ion Monitoring

DOEpatents

Orr, Christopher Henry; Luff, Craig Janson; Dockray, Thomas; Macarthur, Duncan Whittemore

2003-11-18

The apparatus and method provide a technique for significantly reducing capacitance effects in detector electrodes arising due to movement of the instrument relative to the item/location being monitored in ion detection based techniques. The capacitance variations are rendered less significant by placing an electrically conducting element between the detector electrodes and the monitored location/item. Improved sensitivity and reduced noise signals arise as a result. The technique also provides apparatus and method suitable for monitoring elongate items which are unsuited to complete enclosure in one go within a chamber. The items are monitored part by part as the pass through the instrument, so increasing the range of items or locations which can be successfully monitored.

Reducing the anisotropy of a Brazilian disc generated in a bonded-particle model

NASA Astrophysics Data System (ADS)

Zhang, Q.; Zhang, X. P.; Ji, P. Q.

2018-03-01

The Brazilian test is a widely used method for determining the tensile strength of rocks and for calibrating parameters in bonded-particle models (BPMs). In previous studies, the Brazilian disc has typically been trimmed from a compacted rectangular specimen. The present study shows that different tensile strength values are obtained depending on the compressive loading direction. Several measures are proposed to reduce the anisotropy of the disc. The results reveal that the anisotropy of the disc is significantly influenced by the compactibility of the specimen from which it is trimmed. A new method is proposed in which the Brazilian disc is directly generated with a particle boundary, effectively reducing the anisotropy. The stiffness (particle and bond) and strength (bond) of the boundary are set at less than and greater than those of the disc assembly, respectively, which significantly decreases the stress concentration at the boundary contacts and prevents breakage of the boundary particle bonds. This leads to a significant reduction in the anisotropy of the disc and the discreteness of the tensile strength. This method is more suitable for carrying out a realistic Brazilian test for homogeneous rock-like material in the BPM.

Hepatic Tract Plug-Embolisation After Biliary Stenting. Is It Worthwhile?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dale, Adam P., E-mail: adamdale@doctors.org.uk; Khan, Rafeh, E-mail: rafeh.khan@yahoo.com; Mathew, Anup, E-mail: anup.mathew@sth.nhs.uk

PurposePTC and stenting procedures are associated with significant risks including life-threatening haemorrhage, sepsis, renal failure and high mortality rates. PTC tract closure methods are utilised to reduce haemorrhagic complications despite little evidence to support their use. The current study assesses the incidence of haemorrhagic complications following PTC and stenting procedures, both prior to and following the introduction of a dedicated expanding gelatin foam-targeted embolisation liver tract closure technique.Materials and MethodsHaemorrhagic complications were retrospectively identified in patients undergoing PTC procedures both prior to (subgroup 1) and following (subgroup 2) the introduction of a dedicated targeted liver tract closure method between 9/11/2010more » and 10/08/2012 in a single tertiary referral centre. Mean blood Hb decrease following PTC was established in subgroups 1 and 2. Kaplan–Meier life-table analysis was performed to compare survival outcomes between subgroups using the log-rank test.ResultsHaemorrhagic complications were significantly reduced following the introduction of the targeted PTC tract closure method [(12 vs. 3 % of subgroups 1 (n = 101) and 2 (n = 92), respectively (p = 0.027)]. Mean blood Hb decrease following PTC was 1.40 versus 0.68 g/dL in subgroups 1 and 2, respectively (p = 0.069). 30-day mortality was 14 and 12 % in subgroups 1 and 2, respectively. 50 % of the entire cohort had died by 174 days post-PTC.ConclusionIntroduction of liver tract embolisation significantly reduced haemorrhagic complications in our patient cohort. Utilisation of this method has the potential to reduce the morbidity and mortality burden associated with post-PTC haemorrhage by preventing bleeding from the liver access tract.« less

Advanced Guidance and Control Methods for Reusable Launch Vehicles: Test Results

NASA Technical Reports Server (NTRS)

Hanson, John M.; Jones, Robert E.; Krupp, Don R.; Fogle, Frank R. (Technical Monitor)

2002-01-01

There are a number of approaches to advanced guidance and control (AG&C) that have the potential for achieving the goals of significantly increasing reusable launch vehicle (RLV) safety/reliability and reducing the cost. In this paper, we examine some of these methods and compare the results. We briefly introduce the various methods under test, list the test cases used to demonstrate that the desired results are achieved, show an automated test scoring method that greatly reduces the evaluation effort required, and display results of the tests. Results are shown for the algorithms that have entered testing so far.

Improvement of photon correlation spectroscopy method for measuring nanoparticle size by using attenuated total reflectance.

PubMed

Krishtop, Victor; Doronin, Ivan; Okishev, Konstantin

2012-11-05

Photon correlation spectroscopy is an effective method for measuring nanoparticle sizes and has several advantages over alternative methods. However, this method suffers from a disadvantage in that its measuring accuracy reduces in the presence of convective flows of fluid containing nanoparticles. In this paper, we propose a scheme based on attenuated total reflectance in order to reduce the influence of convection currents. The autocorrelation function for the light-scattering intensity was found for this case, and it was shown that this method afforded a significant decrease in the time required to measure the particle sizes and an increase in the measuring accuracy.

[Neurophysiological effect of flavor and caffeine added to toothpaste].

PubMed

Sadachi, Hidetoshi; Murakami, Yoshinori; Hosoya, Manabu; Yada, Yukihiro

2010-01-01

We previously reported that tooth brushing can be used for active resting as a fatigue-reducing method. In this study, we focused on toothpaste, aiming at increasing the fatigue-reducing effect of tooth brushing. Flavoring and caffeine were added to toothpaste, and their effects were investigated employing the Flicker value, event-related potential P300, and mood scale. Thirteen healthy male and female adults (6 males and 7 females, mean age +/- standard deviation: 28.2 +/- 6.5 yr) performed a 25-minute calculation task using a personal computer, brushed their teeth using the toothpaste, and then repeated the calculation task. The P300 peak latency was significantly shortened after tooth brushing with the toothpaste containing flavoring and caffeine, compared to that after brushing with toothpaste containing no additives (p<0.01), and prolongation of the P300 peak latency after the calculation task was significantly inhibited (p<0.01). In addition, the accuracy of the calculation task tended to increase (p<0.1). Regarding the mood scale, "general fatigue" decreased (p<0.1), "lassitude" was significantly reduced (p<0.05), and "feeling of being refreshed" and "feeling of clear-headedness" were significantly increased (p<0.01 and p<0.05, respectively). These findings suggest the usefulness of tooth brushing with toothpaste with added flavoring and caffeine as a fatigue-reducing method.

Concrete mixtures that incorporate inclusions to reduce the sound generated in Portland cement concrete pavements

DOT National Transportation Integrated Search

2004-01-01

Tire-pavement interaction noise is one of the significant environmental problem in highly populated urban areas situated near busy highways. Traditionally, this problem was reduced through the use of sound barriers ; but this method has limitations. ...

Contraceptive method and pregnancy incidence among women in HIV-1-serodiscordant partnerships.

PubMed

Ngure, Kenneth; Heffron, Renee; Mugo, Nelly R; Celum, Connie; Cohen, Craig R; Odoyo, Josephine; Rees, Helen; Kiarie, James N; Were, Edwin; Baeten, Jared M

2012-02-20

Effective contraception reduces unintended pregnancies and is a central strategy to reduce vertical HIV-1 transmission for HIV-1-infected women. Among 2269 HIV-1-seropositive and 1085-seronegative women from seven African countries who were members of HIV-1-serodiscordant heterosexual partnerships and who were participating in an HIV-1 prevention clinical trial, we assessed pregnancy incidence according to contraceptive method using multivariate Andersen-Gill analysis. Compared with women using no contraceptive method, pregnancy incidence was significantly reduced among HIV-1-seropositive and HIV-1-seronegative women using injectable contraception [adjusted hazard ratio (aHR) 0.24, P = 0.001 and aHR 0.25, P < 0.001, respectively). Oral contraceptives significantly reduced pregnancy risk only among HIV-1-seropositive women (aHR 0.51, P = 0.004) but not seronegative women (aHR 0.64, P = 0.3), and, for both seropositive and seronegative women, oral contraceptive pill users were more likely to become pregnant than injectable contraceptive users (aHR 2.22, P = 0.01 for HIV-1-seropositive women and aHR 2.65, P = 0.09 for HIV-1-seronegative women). Condoms, when reported as being used as the primary contraceptive method, marginally reduced pregnancy incidence (aHR 0.85, P = 0.1 for seropositive women and aHR 0.67, P = 0.02 for seronegative women). There were no pregnancies among women using intrauterine devices, implantable methods or who had undergone surgical sterilization, although these methods were used relatively infrequently. Family planning programs and HIV-1 prevention trials need innovative ways to motivate uptake and sustained use of longer acting, less user-dependent contraception for women who do not desire pregnancy.

A simple modification of the separation method reduces heterogeneity of adipose-derived stem cells.

PubMed

Griesche, Nadine; Luttmann, Werner; Luttmann, Arlette; Stammermann, Thekla; Geiger, Helmut; Baer, Patrick C

2010-01-01

High hopes are put into the use of mesenchymal stem cells (MSCs) in various approaches for tissue engineering and regenerative medicine. MSCs are derived from different tissues with only small differences in their phenotype or their differentiation potential, but higher differences in the cell yield. Since fat is easily accessible and contains a high amount of MSCs to be isolated, adipose-derived stem cells (ASCs) are very promising for clinical approaches. ASCs are not a completely homogeneous cell population. Our study was initiated to explore an easy and convenient method to reduce heterogeneity. We tested different isolation methods: (1) the standard isolation method for ASCs based on plastic attachment, (2) the standard method with an initial washing step after 60 min of adherence and (3) immunomagnetic isolation by 4 typical markers (CD49a, CD90, CD105 and CD271). Cells isolated by these methods were evaluated using quantitative PCR and flow cytometry as well as by their differentiation potential. Washing led to a significantly lower expression of desmin, smA and six2, and a higher expression of the stem cell markers nestin, oct-4 and sall-1, compared to standard isolated cells, while the immunomagnetically isolated cells showed no significant changes. All cells independent of the isolation method could be induced to differentiate into adipocytes and osteoblasts. Our study demonstrates that a simple washing step reduces heterogeneity of cultured ASCs according to PCR analysis, whereas the immunomagnetic isolation only showed minor advantages compared to the standard method, but the disadvantage of significantly lower cell yields in the primary isolates. Copyright 2010 S. Karger AG, Basel.

Foot pressures during gait: a comparison of techniques for reducing pressure points.

PubMed

Lawless, M W; Reveal, G T; Laughlin, R T

2001-07-01

Various methods have been used to redistribute plantar surface foot pressure in patients with foot ulcers. This study was conducted to determine the effectiveness of four modalities (fracture walker, fracture walker with insert, and open and closed toe total contact casts) in reducing plantar foot pressure. Ten healthy, normal volunteer subjects had an F-scan sensor (ultra thin shoe insert pressure monitor) placed under the right foot. They then ambulated on a flat surface, maintaining their normal gait. Dynamic plantar pressures were averaged over 10 steps at four different sites (plantar surface of great toe, first metatarsal head, base of fifth metatarsal, and plantar heel). All subjects repeated this sequence under five different testing conditions (barefoot, with a fracture walker, fracture walker with arch support insert, open and closed toe total contact cast). Each subject's barefoot pressures were then compared with the pressures during the different modalities. All four treatment modalities significantly reduced (p < 0.05) plantar pressure at the first metatarsal head (no method was superior). The fracture walker, fracture walker with insert, and open toe total contact cast significantly reduced pressure at the heel. Pressures at the base of the fifth metatarsal and great toe were not significantly reduced with any treatment form. The fracture walker, with and without arch support, and total contact cast can effectively reduce plantar pressure at the heel and first metatarsal head.

Sensitivity analysis and nonlinearity assessment of steam cracking furnace process

NASA Astrophysics Data System (ADS)

Rosli, M. N.; Sudibyo, Aziz, N.

2017-11-01

In this paper, sensitivity analysis and nonlinearity assessment of cracking furnace process are presented. For the sensitivity analysis, the fractional factorial design method is employed as a method to analyze the effect of input parameters, which consist of four manipulated variables and two disturbance variables, to the output variables and to identify the interaction between each parameter. The result of the factorial design method is used as a screening method to reduce the number of parameters, and subsequently, reducing the complexity of the model. It shows that out of six input parameters, four parameters are significant. After the screening is completed, step test is performed on the significant input parameters to assess the degree of nonlinearity of the system. The result shows that the system is highly nonlinear with respect to changes in an air-to-fuel ratio (AFR) and feed composition.

Proactive control of proactive interference using the method of loci.

PubMed

Bass, Willa S; Oswald, Karl M

2014-01-01

Proactive interferencebuilds up with exposure to multiple lists of similar items with a resulting reduction in recall. This study examined the effectiveness of using a proactive strategy of the method of loci to reduce proactive interference in a list recall paradigm of categorically similar words. While all participants reported using some form of strategy to recall list words, this study demonstrated that young adults were able to proactively use the method of loci after 25 min of instruction to reduce proactive interference as compared with other personal spontaneous strategies. The implications of this study are that top-down proactive strategies such as the method of loci can significantly reduce proactive interference, and that the use of image and sequence or location are especially useful in this regard.

Proactive control of proactive interference using the method of loci

PubMed Central

Bass, Willa S.; Oswald, Karl M.

2014-01-01

Proactive interferencebuilds up with exposure to multiple lists of similar items with a resulting reduction in recall. This study examined the effectiveness of using a proactive strategy of the method of loci to reduce proactive interference in a list recall paradigm of categorically similar words. While all participants reported using some form of strategy to recall list words, this study demonstrated that young adults were able to proactively use the method of loci after 25 min of instruction to reduce proactive interference as compared with other personal spontaneous strategies. The implications of this study are that top-down proactive strategies such as the method of loci can significantly reduce proactive interference, and that the use of image and sequence or location are especially useful in this regard. PMID:25157300

Speckle-reducing scale-invariant feature transform match for synthetic aperture radar image registration

NASA Astrophysics Data System (ADS)

Wang, Xianmin; Li, Bo; Xu, Qizhi

2016-07-01

The anisotropic scale space (ASS) is often used to enhance the performance of a scale-invariant feature transform (SIFT) algorithm in the registration of synthetic aperture radar (SAR) images. The existing ASS-based methods usually suffer from unstable keypoints and false matches, since the anisotropic diffusion filtering has limitations in reducing the speckle noise from SAR images while building the ASS image representation. We proposed a speckle reducing SIFT match method to obtain stable keypoints and acquire precise matches for the SAR image registration. First, the keypoints are detected in a speckle reducing anisotropic scale space constructed by the speckle reducing anisotropic diffusion, so that speckle noise is greatly reduced and prominent structures of the images are preserved, consequently the stable keypoints can be derived. Next, the probabilistic relaxation labeling approach is employed to establish the matches of the keypoints then the correct match rate of the keypoints is significantly increased. Experiments conducted on simulated speckled images and real SAR images demonstrate the effectiveness of the proposed method.

Pulse transmission transceiver architecture for low power communications

DOEpatents

Dress, Jr., William B.; Smith, Stephen F.

2003-08-05

Systems and methods for pulse-transmission low-power communication modes are disclosed. A method of pulse transmission communications includes: generating a modulated pulse signal waveform; transforming said modulated pulse signal waveform into at least one higher-order derivative waveform; and transmitting said at least one higher-order derivative waveform as an emitted pulse. The systems and methods significantly reduce lower-frequency emissions from pulse transmission spread-spectrum communication modes, which reduces potentially harmful interference to existing radio frequency services and users and also simultaneously permit transmission of multiple data bits by utilizing specific pulse shapes.

Sucrose and color profiles in sugarcane (Saccharum sp.) juice analyzed by UFLC-ELSD and Synapt High-Definition Mass Spectrometry during radiation treatment

NASA Astrophysics Data System (ADS)

Lima, Roberta B.; de Aguiar, Claudio Lima; Galaverna, Renan; Baptista, Antonio S.; Eberlin, Marcos N.; Arthur, Valter

2016-04-01

This work evaluated the effect of electron beam irradiation (E-beam) on sugarcane juice and compared the results with preliminary tests performed on sugarcane juice treated with gamma irradiation. The samples were irradiated at 5, 10 and 20 kGy doses and results were compared wile control samples without irradiation. The results showed a significant increase (p≤0.05) of phenolic compounds in both treatments. We also observed increased contents of reducing sugars (glucose and fructose) for the samples irradiated with gamma rays and E-beam measured by the DNS methods. However, there was no significant difference of sugars content measured by chromatographic analyses performed in the sugarcane juice treated with E-beam. Therefore reducing sugars content could be overestimated by the DNS method because salts in sugarcane juice. The treatments were able to reduce sugarcane juice ICUMSA color intensity in both treatments with irradiation. E-beam reduced sugarcane juice color by roughly 49% compared the control, while gamma irradiation reduced it by 30%.

Studying relaxation phenomena via effective master equations

NASA Astrophysics Data System (ADS)

Chan, David; Wan, Jones T. K.; Chu, L. L.; Yu, K. W.

2000-04-01

The real-time dynamics of various relaxation phenomena can be conveniently formulated by a master equation with the enumeration of transition rates between given classes of conformations. To study the relaxation time towards equilibrium, it suffices to solve for the second largest eigenvalue of the resulting eigenvalue equation. Generally speaking, there is no analytic solution for the dynamic equation. Mean-field approaches generally yield misleading results while the presumably exact Monte-Carlo methods require prohibitive time steps in most real systems. In this work, we propose an exact decimation procedure for reducing the number of conformations significantly, while there is no loss of information, i.e., the reduced (or effective) equation is an exact transformed version of the original one. However, we have to pay the price: the initial Markovianity of the evolution equation is lost and the reduced equation contains memory terms in the transition rates. Since the transformed equation has significantly reduced number of degrees of freedom, the systems can readily be diagonalized by iterative means, to obtain the exact second largest eigenvalue and hence the relaxation time. The decimation method has been applied to various relaxation equations with generally desirable results. The advantages and limitations of the method will be discussed.

Whole genome prediction and heritability of childhood asthma phenotypes.

PubMed

McGeachie, Michael J; Clemmer, George L; Croteau-Chonka, Damien C; Castaldi, Peter J; Cho, Michael H; Sordillo, Joanne E; Lasky-Su, Jessica A; Raby, Benjamin A; Tantisira, Kelan G; Weiss, Scott T

2016-12-01

While whole genome prediction (WGP) methods have recently demonstrated successes in the prediction of complex genetic diseases, they have not yet been applied to asthma and related phenotypes. Longitudinal patterns of lung function differ between asthmatics, but these phenotypes have not been assessed for heritability or predictive ability. Herein, we assess the heritability and genetic predictability of asthma-related phenotypes. We applied several WGP methods to a well-phenotyped cohort of 832 children with mild-to-moderate asthma from CAMP. We assessed narrow-sense heritability and predictability for airway hyperresponsiveness, serum immunoglobulin E, blood eosinophil count, pre- and post-bronchodilator forced expiratory volume in 1 sec (FEV 1 ), bronchodilator response, steroid responsiveness, and longitudinal patterns of lung function (normal growth, reduced growth, early decline, and their combinations). Prediction accuracy was evaluated using a training/testing set split of the cohort. We found that longitudinal lung function phenotypes demonstrated significant narrow-sense heritability (reduced growth, 95%; normal growth with early decline, 55%). These same phenotypes also showed significant polygenic prediction (areas under the curve [AUCs] 56% to 62%). Including additional demographic covariates in the models increased prediction 4-8%, with reduced growth increasing from 62% to 66% AUC. We found that prediction with a genomic relatedness matrix was improved by filtering available SNPs based on chromatin evidence, and this result extended across cohorts. Longitudinal reduced lung function growth displayed extremely high heritability. All phenotypes with significant heritability showed significant polygenic prediction. Using SNP-prioritization increased prediction across cohorts. WGP methods show promise in predicting asthma-related heritable traits.

Limb lengthening over a nail can safely reduce the duration of external fixation

PubMed Central

Chaudhary, Milind

2008-01-01

Background: Limb lengthening using Ilizarov external fixation is safe, but the consolidation phase tends to take too long. A method that can safely reduce the time spent in external fixation would help increase patient tolerance and comfort. We report our results of lengthening over nails (LON) method in which an interlocking nail was used along with an Ilizarov external fixator to reduce external fixation duration in limb lengthening. This is a retrospective study. Materials and Methods: Twenty-seven lengthening surgeries were done with the LON method in 23 patients with 22 tibiae and five femora during the last 12 years. Length gain ranged from 1.5 cm to a maximum of 9.8 cm with a mean of 4.6 cm. The mean modified Paley difficulty score was 7.6 points. Fourteen associated procedures were performed in these patients, including equinus contracture releases, supracondylar osteotomies, ilizarov hip reonstruction and ankle fusion. We had a 29% rate of complications which included one problem, three obstacles and four complications with no serious deep intramedullary infections. Our rate of complications compares favorably with series reported in the literature. External fixation duration was reduced significantly to a mean of 17.8 days per cm. Conclusions: A combination of intramedullary nailing along with external fixation significantly reduces external fixation time while maintaining low rate of complications. Great care needs to be taken to prevent pin track infection and deep intramedullary sepsis. PMID:19753160

Anti-inflammatory, Analgesic and Antiulcer properties of Porphyra vietnamensis.

PubMed

Bhatia, Saurabh; Sharma, Kiran; Sharma, Ajay; Nagpal, Kalpana; Bera, Tanmoy

2015-01-01

Aim of the present work was to investigate the anti-inflammatory, analgesic and antiulcer effects of red seaweed Porphyra vietnamensis (P. vietnamenis). Aqueous (POR) and alcoholic (PE) fractions were successfully isolated from P. vietnamenis. Further biological investigations were performed using a classic test of paw edema induced by carrageenan, writhing induced by acetic acid, hot plate method and naproxen induced gastro-duodenal ulcer. Among the fractions POR showed better activity. POR and PE significantly (p < 0.05) reduced carrageenan induced paw edema in a dose dependent manner. In the writhing test POR significantly (p < 0.05) reduced abdominal writhes than PE. In hot plate method POR showed better analgesic activity than PE. POR showed comparable ulcers reducing potential (p<0.01) to that of omeprazole, and has more ulcer reducing potential then PE. The results of this study demonstrated that P. vietnamenis aqueous fraction possesses biological activity that is close to the standards taken for the treatment of peripheral painful or/and inflammatory and ulcer conditions.

Inter-Labeler and Intra-Labeler Variability of Condition Severity Classification Models Using Active and Passive Learning Methods

PubMed Central

Nissim, Nir; Shahar, Yuval; Boland, Mary Regina; Tatonetti, Nicholas P; Elovici, Yuval; Hripcsak, George; Moskovitch, Robert

2018-01-01

Background and Objectives Labeling instances by domain experts for classification is often time consuming and expensive. To reduce such labeling efforts, we had proposed the application of active learning (AL) methods, introduced our CAESAR-ALE framework for classifying the severity of clinical conditions, and shown its significant reduction of labeling efforts. The use of any of three AL methods (one well known [SVM-Margin], and two that we introduced [Exploitation and Combination_XA]) significantly reduced (by 48% to 64%) condition labeling efforts, compared to standard passive (random instance-selection) SVM learning. Furthermore, our new AL methods achieved maximal accuracy using 12% fewer labeled cases than the SVM-Margin AL method. However, because labelers have varying levels of expertise, a major issue associated with learning methods, and AL methods in particular, is how to best to use the labeling provided by a committee of labelers. First, we wanted to know, based on the labelers’ learning curves, whether using AL methods (versus standard passive learning methods) has an effect on the Intra-labeler variability (within the learning curve of each labeler) and inter-labeler variability (among the learning curves of different labelers). Then, we wanted to examine the effect of learning (either passively or actively) from the labels created by the majority consensus of a group of labelers. Methods We used our CAESAR-ALE framework for classifying the severity of clinical conditions, the three AL methods and the passive learning method, as mentioned above, to induce the classifications models. We used a dataset of 516 clinical conditions and their severity labeling, represented by features aggregated from the medical records of 1.9 million patients treated at Columbia University Medical Center. We analyzed the variance of the classification performance within (intra-labeler), and especially among (inter-labeler) the classification models that were induced by using the labels provided by seven labelers. We also compared the performance of the passive and active learning models when using the consensus label. Results The AL methods produced, for the models induced from each labeler, smoother Intra-labeler learning curves during the training phase, compared to the models produced when using the passive learning method. The mean standard deviation of the learning curves of the three AL methods over all labelers (mean: 0.0379; range: [0.0182 to 0.0496]), was significantly lower (p = 0.049) than the Intra-labeler standard deviation when using the passive learning method (mean: 0.0484; range: [0.0275 to 0.0724). Using the AL methods resulted in a lower mean Inter-labeler AUC standard deviation among the AUC values of the labelers’ different models during the training phase, compared to the variance of the induced models’ AUC values when using passive learning. The Inter-labeler AUC standard deviation, using the passive learning method (0.039), was almost twice as high as the Inter-labeler standard deviation using our two new AL methods (0.02 and 0.019, respectively). The SVM-Margin AL method resulted in an Inter-labeler standard deviation (0.029) that was higher by almost 50% than that of our two AL methods. The difference in the inter-labeler standard deviation between the passive learning method and the SVM-Margin learning method was significant (p = 0.042). The difference between the SVM-Margin and Exploitation method was insignificant (p = 0.29), as was the difference between the Combination_XA and Exploitation methods (p = 0.67). Finally, using the consensus label led to a learning curve that had a higher mean intra-labeler variance, but resulted eventually in an AUC that was at least as high as the AUC achieved using the gold standard label and that was always higher than the expected mean AUC of a randomly selected labeler, regardless of the choice of learning method (including a passive learning method). Using a paired t-test, the difference between the intra-labeler AUC standard deviation when using the consensus label, versus that value when using the other two labeling strategies, was significant only when using the passive learning method (p = 0.014), but not when using any of the three AL methods. Conclusions The use of AL methods, (a) reduces intra-labeler variability in the performance of the induced models during the training phase, and thus reduces the risk of halting the process at a local minimum that is significantly different in performance from the rest of the learned models; and (b) reduces Inter-labeler performance variance, and thus reduces the dependence on the use of a particular labeler. In addition, the use of a consensus label, agreed upon by a rather uneven group of labelers, might be at least as good as using the gold standard labeler, who might not be available, and certainly better than randomly selecting one of the group’s individual labelers. Finally, using the AL methods when provided by the consensus label reduced the intra-labeler AUC variance during the learning phase, compared to using passive learning. PMID:28456512

A method for reducing sampling jitter in digital control systems

NASA Technical Reports Server (NTRS)

Anderson, T. O.; HURBD W. J.; Hurd, W. J.

1969-01-01

Digital phase lock loop system is designed by smoothing the proportional control with a low pass filter. This method does not significantly affect the loop dynamics when the smoothing filter bandwidth is wide compared to loop bandwidth.

Standard-, Reduced-, and No-Dose Thin-Section Radiologic Examinations: Comparison of Capability for Nodule Detection and Nodule Type Assessment in Patients Suspected of Having Pulmonary Nodules.

PubMed

Ohno, Yoshiharu; Koyama, Hisanobu; Yoshikawa, Takeshi; Kishida, Yuji; Seki, Shinichiro; Takenaka, Daisuke; Yui, Masao; Miyazaki, Mitsue; Sugimura, Kazuro

2017-08-01

Purpose To compare the capability of pulmonary thin-section magnetic resonance (MR) imaging with ultrashort echo time (UTE) with that of standard- and reduced-dose thin-section computed tomography (CT) in nodule detection and evaluation of nodule type. Materials and Methods The institutional review board approved this study, and written informed consent was obtained from each patient. Standard- and reduced-dose chest CT (60 and 250 mA) and MR imaging with UTE were used to examine 52 patients; 29 were men (mean age, 66.4 years ± 7.3 [standard deviation]; age range, 48-79 years) and 23 were women (mean age, 64.8 years ± 10.1; age range, 42-83 years). Probability of nodule presence was assessed for all methods with a five-point visual scoring system. All nodules were then classified as missed, ground-glass, part-solid, or solid nodules. To compare nodule detection capability of the three methods, consensus for performances was rated by using jackknife free-response receiver operating characteristic analysis, and κ analysis was used to compare intermethod agreement for nodule type classification. Results There was no significant difference (F = 0.70, P = .59) in figure of merit between methods (standard-dose CT, 0.86; reduced-dose CT, 0.84; MR imaging with UTE, 0.86). There was no significant difference in sensitivity between methods (standard-dose CT vs reduced-dose CT, P = .50; standard-dose CT vs MR imaging with UTE, P = .50; reduced-dose CT vs MR imaging with UTE, P >.99). Intermethod agreement was excellent (standard-dose CT vs reduced-dose CT, κ = 0.98, P < .001; standard-dose CT vs MR imaging with UTE, κ = 0.98, P < .001; reduced-dose CT vs MR imaging with UTE, κ = 0.99, P < .001). Conclusion Pulmonary thin-section MR imaging with UTE was useful in nodule detection and evaluation of nodule type, and it is considered at least as efficacious as standard- or reduced-dose thin-section CT. © RSNA, 2017 Online supplemental material is available for this article.

Image-guided spatial localization of heterogeneous compartments for magnetic resonance

PubMed Central

An, Li; Shen, Jun

2015-01-01

Purpose: Image-guided localization SPectral Localization Achieved by Sensitivity Heterogeneity (SPLASH) allows rapid measurement of signals from irregularly shaped anatomical compartments without using phase encoding gradients. Here, the authors propose a novel method to address the issue of heterogeneous signal distribution within the localized compartments. Methods: Each compartment was subdivided into multiple subcompartments and their spectra were solved by Tikhonov regularization to enforce smoothness within each compartment. The spectrum of a given compartment was generated by combining the spectra of the components of that compartment. The proposed method was first tested using Monte Carlo simulations and then applied to reconstructing in vivo spectra from irregularly shaped ischemic stroke and normal tissue compartments. Results: Monte Carlo simulations demonstrate that the proposed regularized SPLASH method significantly reduces localization and metabolite quantification errors. In vivo results show that the intracompartment regularization results in ∼40% reduction of error in metabolite quantification. Conclusions: The proposed method significantly reduces localization errors and metabolite quantification errors caused by intracompartment heterogeneous signal distribution. PMID:26328977

Inter-labeler and intra-labeler variability of condition severity classification models using active and passive learning methods.

PubMed

Nissim, Nir; Shahar, Yuval; Elovici, Yuval; Hripcsak, George; Moskovitch, Robert

2017-09-01

Labeling instances by domain experts for classification is often time consuming and expensive. To reduce such labeling efforts, we had proposed the application of active learning (AL) methods, introduced our CAESAR-ALE framework for classifying the severity of clinical conditions, and shown its significant reduction of labeling efforts. The use of any of three AL methods (one well known [SVM-Margin], and two that we introduced [Exploitation and Combination_XA]) significantly reduced (by 48% to 64%) condition labeling efforts, compared to standard passive (random instance-selection) SVM learning. Furthermore, our new AL methods achieved maximal accuracy using 12% fewer labeled cases than the SVM-Margin AL method. However, because labelers have varying levels of expertise, a major issue associated with learning methods, and AL methods in particular, is how to best to use the labeling provided by a committee of labelers. First, we wanted to know, based on the labelers' learning curves, whether using AL methods (versus standard passive learning methods) has an effect on the Intra-labeler variability (within the learning curve of each labeler) and inter-labeler variability (among the learning curves of different labelers). Then, we wanted to examine the effect of learning (either passively or actively) from the labels created by the majority consensus of a group of labelers. We used our CAESAR-ALE framework for classifying the severity of clinical conditions, the three AL methods and the passive learning method, as mentioned above, to induce the classifications models. We used a dataset of 516 clinical conditions and their severity labeling, represented by features aggregated from the medical records of 1.9 million patients treated at Columbia University Medical Center. We analyzed the variance of the classification performance within (intra-labeler), and especially among (inter-labeler) the classification models that were induced by using the labels provided by seven labelers. We also compared the performance of the passive and active learning models when using the consensus label. The AL methods: produced, for the models induced from each labeler, smoother Intra-labeler learning curves during the training phase, compared to the models produced when using the passive learning method. The mean standard deviation of the learning curves of the three AL methods over all labelers (mean: 0.0379; range: [0.0182 to 0.0496]), was significantly lower (p=0.049) than the Intra-labeler standard deviation when using the passive learning method (mean: 0.0484; range: [0.0275-0.0724). Using the AL methods resulted in a lower mean Inter-labeler AUC standard deviation among the AUC values of the labelers' different models during the training phase, compared to the variance of the induced models' AUC values when using passive learning. The Inter-labeler AUC standard deviation, using the passive learning method (0.039), was almost twice as high as the Inter-labeler standard deviation using our two new AL methods (0.02 and 0.019, respectively). The SVM-Margin AL method resulted in an Inter-labeler standard deviation (0.029) that was higher by almost 50% than that of our two AL methods The difference in the inter-labeler standard deviation between the passive learning method and the SVM-Margin learning method was significant (p=0.042). The difference between the SVM-Margin and Exploitation method was insignificant (p=0.29), as was the difference between the Combination_XA and Exploitation methods (p=0.67). Finally, using the consensus label led to a learning curve that had a higher mean intra-labeler variance, but resulted eventually in an AUC that was at least as high as the AUC achieved using the gold standard label and that was always higher than the expected mean AUC of a randomly selected labeler, regardless of the choice of learning method (including a passive learning method). Using a paired t-test, the difference between the intra-labeler AUC standard deviation when using the consensus label, versus that value when using the other two labeling strategies, was significant only when using the passive learning method (p=0.014), but not when using any of the three AL methods. The use of AL methods, (a) reduces intra-labeler variability in the performance of the induced models during the training phase, and thus reduces the risk of halting the process at a local minimum that is significantly different in performance from the rest of the learned models; and (b) reduces Inter-labeler performance variance, and thus reduces the dependence on the use of a particular labeler. In addition, the use of a consensus label, agreed upon by a rather uneven group of labelers, might be at least as good as using the gold standard labeler, who might not be available, and certainly better than randomly selecting one of the group's individual labelers. Finally, using the AL methods: when provided by the consensus label reduced the intra-labeler AUC variance during the learning phase, compared to using passive learning. Copyright © 2017 Elsevier B.V. All rights reserved.

Progressive Band Selection

NASA Technical Reports Server (NTRS)

Fisher, Kevin; Chang, Chein-I

2009-01-01

Progressive band selection (PBS) reduces spectral redundancy without significant loss of information, thereby reducing hyperspectral image data volume and processing time. Used onboard a spacecraft, it can also reduce image downlink time. PBS prioritizes an image's spectral bands according to priority scores that measure their significance to a specific application. Then it uses one of three methods to select an appropriate number of the most useful bands. Key challenges for PBS include selecting an appropriate criterion to generate band priority scores, and determining how many bands should be retained in the reduced image. The image's Virtual Dimensionality (VD), once computed, is a reasonable estimate of the latter. We describe the major design details of PBS and test PBS in a land classification experiment.

Dual energy CT: How well can pseudo-monochromatic imaging reduce metal artifacts?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuchenbecker, Stefan, E-mail: stefan.kuchenbecker@dkfz.de; Faby, Sebastian; Sawall, Stefan

2015-02-15

Purpose: Dual Energy CT (DECT) provides so-called monoenergetic images based on a linear combination of the original polychromatic images. At certain patient-specific energy levels, corresponding to certain patient- and slice-dependent linear combination weights, e.g., E = 160 keV corresponds to α = 1.57, a significant reduction of metal artifacts may be observed. The authors aimed at analyzing the method for its artifact reduction capabilities to identify its limitations. The results are compared with raw data-based processing. Methods: Clinical DECT uses a simplified version of monochromatic imaging by linearly combining the low and the high kV images and by assigning an energymore » to that linear combination. Those pseudo-monochromatic images can be used by radiologists to obtain images with reduced metal artifacts. The authors analyzed the underlying physics and carried out a series expansion of the polychromatic attenuation equations. The resulting nonlinear terms are responsible for the artifacts, but they are not linearly related between the low and the high kV scan: A linear combination of both images cannot eliminate the nonlinearities, it can only reduce their impact. Scattered radiation yields additional noncanceling nonlinearities. This method is compared to raw data-based artifact correction methods. To quantify the artifact reduction potential of pseudo-monochromatic images, they simulated the FORBILD abdomen phantom with metal implants, and they assessed patient data sets of a clinical dual source CT system (100, 140 kV Sn) containing artifacts induced by a highly concentrated contrast agent bolus and by metal. In each case, they manually selected an optimal α and compared it to a raw data-based material decomposition in case of simulation, to raw data-based material decomposition of inconsistent rays in case of the patient data set containing contrast agent, and to the frequency split normalized metal artifact reduction in case of the metal implant. For each case, the contrast-to-noise ratio (CNR) was assessed. Results: In the simulation, the pseudo-monochromatic images yielded acceptable artifact reduction results. However, the CNR in the artifact-reduced images was more than 60% lower than in the original polychromatic images. In contrast, the raw data-based material decomposition did not significantly reduce the CNR in the virtual monochromatic images. Regarding the patient data with beam hardening artifacts and with metal artifacts from small implants the pseudo-monochromatic method was able to reduce the artifacts, again with the downside of a significant CNR reduction. More intense metal artifacts, e.g., as those caused by an artificial hip joint, could not be suppressed. Conclusions: Pseudo-monochromatic imaging is able to reduce beam hardening, scatter, and metal artifacts in some cases but it cannot remove them. In all cases, the CNR is significantly reduced, thereby rendering the method questionable, unless special post processing algorithms are implemented to restore the high CNR from the original images (e.g., by using a frequency split technique). Raw data-based dual energy decomposition methods should be preferred, in particular, because the CNR penalty is almost negligible.« less

Reformulated diesel fuel and method

DOEpatents

McAdams, Hiramie T [Carrollton, IL; Crawford, Robert W [Tucson, AZ; Hadder, Gerald R [Oak Ridge, TN; McNutt, Barry D [Arlington, VA

2006-08-22

A method for mathematically identifying at least one diesel fuel suitable for combustion in an automotive diesel engine with significantly reduced emissions and producible from known petroleum blendstocks using known refining processes, including the use of cetane additives (ignition improvers) and oxygenated compounds.

Vibration analysis of rotor systems using reduced subsystem models

NASA Technical Reports Server (NTRS)

Fan, Uei-Jiun; Noah, Sherif T.

1989-01-01

A general impedance method using reduced submodels has been developed for the linear dynamic analysis of rotor systems. Formulated in terms of either modal or physical coordinates of the subsystems, the method enables imbalance responses at specific locations of the rotor systems to be efficiently determined from a small number of 'master' degrees of freedom. To demonstrate the capability of this impedance approach, the Space Shuttle Main Engine high-pressure oxygen turbopump has been investigated to determine the bearing loads due to imbalance. Based on the same formulation, an eigenvalue analysis has been performed to study the system stability. A small 5-DOF model has been utilized to illustrate the application of the method to eigenvalue analysis. Because of its inherent characteristics of allowing formulation of reduced submodels, the impedance method can significantly increase the computational speed.

Measuring Range Anxiety: the Substitution-Emergency-Detour (SED) Method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Zhenhong

Range anxiety has been widely recognized as a critical barrier for battery electric vehicles (BEV), but its measurement method is lacking. Such a knowledge gap makes it difficult to analyse the competiveness of and the demand for BEVs. This study develops the Substitution-Emergency-Detour (SED) method to measure the range anxiety cost, and conducts sensitivity analysis of range anxiety cost with respect to nine factors. It is found that the most effective ways to reduce range anxiety are reducing driving intensity, increasing the vehicle range, extending the vehicle range with better charging infrastructure. Better household vehicle flexibility and less range uncertaintymore » can also significantly reduce range anxiety. The SED method and the numerical results are expected to contribute to better understanding of the range anxiety barrier and the BEV demand.« less

Reducing State Communication Anxiety for Public Speakers: An Energy Psychology Pilot Study

ERIC Educational Resources Information Center

Fitch, John, III; Schmuldt, Laura; Rudick, Karen L.

2011-01-01

This mixed-method pilot study investigates the efficacy of implementing primordial energy activation and transcendence to address public speaking anxiety. Speech anxiety was significantly reduced from pretest to posttest, as measured by the Communication Anxiety Inventory State. Suggestions for future research, limitations of the current study,…

Effects of Two Short-Term Desensitization Methods in the Treatment of Test Anxiety

ERIC Educational Resources Information Center

Richardson, Frank C.; Suinn, Richard M.

1974-01-01

Accelerated massed desensitization and anxiety management training were compared with standard systematic desensitization in terms of reducing self-reported test anxiety in high test-anxious college students. All three treatments significantly reduced test anxiety as compared with a waiting list control group. (Author)

Granulation tissue formation at the bronchial stump is reduced after stapler closure in comparison to suture closure in dogs.

PubMed

Izumi, Yotaro; Kawamura, Masafumi; Gika, Masatoshi; Nomori, Hiroaki

2010-03-01

The aim of this study was to compare the morphology of the bronchial stump after lobectomy between mechanical stapler closure and manual suture closure. The effect of fibrin glue application on each method of closure was also observed. Right upper lobectomy was performed in beagles (n=31) using staplers (ST group) or sutures (SU group). In a separate experiment, fibrin glue was sprayed onto the stump after each respective method of closure. After one week, the stump region was examined macroscopically, and also by histology. chi(2)-Test and Mann-Whitney test were used for comparative analysis. The incidence of adhesion formation between the surrounding tissues was significantly reduced in the ST group in comparison to the SU group (22 vs. 80%, P=0.04). The thickness of granulation tissue over the stump was significantly reduced in the ST group in comparison to the SU group (0.8+/-0.2 vs. 2.5+/-0.3 mm, P<0.0001). Vessel density in the granulation tissue was also significantly reduced in the ST group in comparison to the SU group (6+/-2 vs. 16+/-2, P=0.003). Fibrin glue application after stapler closure significantly increased the incidence of adhesion formation, granulation tissue thickness, and vessel density in the granulation tissue over the stump.

The impact of slice-reduced computed tomography on histogram-based densitometry assessment of lung fibrosis in patients with systemic sclerosis

PubMed Central

Maurer, Britta; Suliman, Yossra A.; Morsbach, Fabian; Distler, Oliver; Frauenfelder, Thomas

2018-01-01

Background To evaluate usability of slice-reduced sequential computed tomography (CT) compared to standard high-resolution CT (HRCT) in patients with systemic sclerosis (SSc) for qualitative and quantitative assessment of interstitial lung disease (ILD) with respect to (I) detection of lung parenchymal abnormalities, (II) qualitative and semiquantitative visual assessment, (III) quantification of ILD by histograms and (IV) accuracy for the 20%-cut off discrimination. Methods From standard chest HRCT of 60 SSc patients sequential 9-slice-computed tomography (reduced HRCT) was retrospectively reconstructed. ILD was assessed by visual scoring and quantitative histogram parameters. Results from standard and reduced HRCT were compared using non-parametric tests and analysed by univariate linear regression analyses. Results With respect to the detection of parenchymal abnormalities, only the detection of intrapulmonary bronchiectasis was significantly lower in reduced HRCT compared to standard HRCT (P=0.039). No differences were found comparing visual scores for fibrosis severity and extension from standard and reduced HRCT (P=0.051–0.073). All scores correlated significantly (P<0.001) to histogram parameters derived from both, standard and reduced HRCT. Significant higher values of kurtosis and skewness for reduced HRCT were found (both P<0.001). In contrast to standard HRCT histogram parameters from reduced HRCT showed significant discrimination at cut-off 20% fibrosis (sensitivity 88% kurtosis and skewness; specificity 81% kurtosis and 86% skewness; cut-off kurtosis ≤26, cut-off skewness ≤4; both P<0.001). Conclusions Reduced HRCT is a robust method to assess lung fibrosis in SSc with minimal radiation dose with no difference in scoring assessment of lung fibrosis severity and extension in comparison to standard HRCT. In contrast to standard HRCT histogram parameters derived from the approach of reduced HRCT could discriminate at a threshold of 20% lung fibrosis with high sensitivity and specificity. Hence it might be used to detect early disease progression of lung fibrosis in context of monitoring and treatment of SSc patients. PMID:29850118

Antioxidant Peptides Identified from Ovotransferrin by the ORAC Method Did Not Show Anti-Inflammatory and Antioxidant Activities in Endothelial Cells.

PubMed

Jahandideh, Forough; Chakrabarti, Subhadeep; Davidge, Sandra T; Wu, Jianping

2016-01-13

Oxygen radical absorbance capacity (ORAC) is a widely used method of measuring antioxidant capacities of various antioxidant components. Surprisingly, 16 antioxidant peptides previously identified from egg protein ovotransferrin using the ORAC method did not show any anti-inflammatory and antioxidant activities in cells. After simulated gastro-intestinal digestion (GID), several peptide digests significantly reduced the expression of tumor necrosis factor-α (TNF-α)-induced pro-inflammatory intercellular cell adhesion molecule-1 (ICAM-1) by 65.7 ± 10.4% and vascular cell adhesion molecule-1 (VCAM-1) by 53.5 ± 9.6% to 61.0 ± 14.5%, but only GWNI reduced TNF-α-activated superoxide generation by 71.0 ± 12.9% when tested with dihydroethidium (DHE) assay. Mass spectrometer analysis identified two new peptides, GWN and GW, in the GWNI digest; however, only GW reduced TNF-α-induced VCAM-1 expression (64.3 ± 20.6%) significantly compared to the TNF-α treated cells. Our study suggested that ORAC lacked biological relevance in assessing bioactive peptides.

Optimization of optical proximity correction to reduce mask write time using genetic algorithm

NASA Astrophysics Data System (ADS)

Dick, Gregory J.; Cao, Liang; Asthana, Abhishek; Cheng, Jing; Power, David N.

2018-03-01

The ever increasing pattern densities and design complexities make the tuning of optical proximity correction (OPC) recipes very challenging. One known method for tuning is genetic algorithm (GA). Previously GA has been demonstrated to fine tune OPC recipes in order to achieve better results for possible 1D and 2D geometric concerns like bridging and pinching. This method, however, did not take into account the impact of excess segmentation on downstream operations like fracturing and mask writing. This paper introduces a general methodology to significantly reduce the number of excess edges in the OPC output, thus reducing the number of flashes generated at fracture and subsequently the write time at mask build. GA is used to reduce the degree of unwarranted segmentation while ensuring good OPC quality. An Objective Function (OF) is utilized to ensure quality convergence and process-variation (PV) plus an additional weighed factor to reduce clustered edge count. The technique is applied to 14nm metal layer OPC recipes in order to identify excess segmentation and to produce a modified recipe that significantly reduces these segments. OPC output file sizes is shown to be reduced by 15% or more and overall edge count is shown to be reduced by 10% or more. At the same time overall quality of the OPC recipe is shown to be maintained via OPC Verification (OPCV) results.

An intertwined method for making low-rank, sum-of-product basis functions that makes it possible to compute vibrational spectra of molecules with more than 10 atoms

PubMed Central

Thomas, Phillip S.

2017-01-01

We propose a method for solving the vibrational Schrödinger equation with which one can compute spectra for molecules with more than ten atoms. It uses sum-of-product (SOP) basis functions stored in a canonical polyadic tensor format and generated by evaluating matrix-vector products. By doing a sequence of partial optimizations, in each of which the factors in a SOP basis function for a single coordinate are optimized, the rank of the basis functions is reduced as matrix-vector products are computed. This is better than using an alternating least squares method to reduce the rank, as is done in the reduced-rank block power method. Partial optimization is better because it speeds up the calculation by about an order of magnitude and allows one to significantly reduce the memory cost. We demonstrate the effectiveness of the new method by computing vibrational spectra of two molecules, ethylene oxide (C2H4O) and cyclopentadiene (C5H6), with 7 and 11 atoms, respectively. PMID:28571348

An intertwined method for making low-rank, sum-of-product basis functions that makes it possible to compute vibrational spectra of molecules with more than 10 atoms.

PubMed

Thomas, Phillip S; Carrington, Tucker

2017-05-28

We propose a method for solving the vibrational Schrödinger equation with which one can compute spectra for molecules with more than ten atoms. It uses sum-of-product (SOP) basis functions stored in a canonical polyadic tensor format and generated by evaluating matrix-vector products. By doing a sequence of partial optimizations, in each of which the factors in a SOP basis function for a single coordinate are optimized, the rank of the basis functions is reduced as matrix-vector products are computed. This is better than using an alternating least squares method to reduce the rank, as is done in the reduced-rank block power method. Partial optimization is better because it speeds up the calculation by about an order of magnitude and allows one to significantly reduce the memory cost. We demonstrate the effectiveness of the new method by computing vibrational spectra of two molecules, ethylene oxide (C 2 H 4 O) and cyclopentadiene (C 5 H 6 ), with 7 and 11 atoms, respectively.

Microdrop preparation factors influence culture-media osmolality, which can impair mouse embryo preimplantation development.

PubMed

Swain, J E; Cabrera, L; Xu, X; Smith, G D

2012-02-01

Because media osmolality can impact embryo development, the effect of conditions during microdrop preparation on osmolality was examined. Various sizes of microdrops were prepared under different laboratory conditions. Drops were pipetted directly onto a dish and covered by oil (standard method) or pipetted on the dish, overlaid with oil before removing the underlying media and replaced with fresh media (wash-drop method). Drops were made at 23°C or on a heated stage (37°C) and with or without airflow. Osmolality was assessed at 5 min and 24h. The biological impact of osmolality change was demonstrated by culturing 1-cell mouse embryos in media with varying osmolality. Reduced drop volume, increased temperature and standard method were associated with a significant increase in osmolality at both 5 min and 24h (P-values <0.001, <0.0001 and <0.0001, respectively). There was a significant interaction between airflow, decreased volume, increased temperature and standard method that caused a significant increase in osmolality (40mOsm/kg) compared with controls (P<0.04). There was no significant change in osmolality over time. Mouse embryo development was significantly reduced in media with elevated osmolality (>310mOsm/kg; P<0.05). Procedures in the IVF laboratory can alter osmolality and impact embryo development. Copyright © 2011 Reproductive Healthcare Ltd. Published by Elsevier Ltd. All rights reserved.

Improved Method for Determination of Respiring Individual Microorganisms in Natural Waters

PubMed Central

Tabor, Paul S.; Neihof, Rex A.

1982-01-01

A method is reported that combines the microscopic determinations of specific, individual, respiring microorganisms by the detection of electron transport system activity and the total number of organisms of an estuarine population by epifluorescence microscopy. An active cellular electron transport system specifically reduces 2-(p-iodophenyl)-3-(p-nitrophenyl)-5-phenyl tetrazolium chloride (INT) to INT-formazan, which is recognized as opaque intracellular deposits in microorganisms stained with acridine orange. In a comparison of previously described sample preparation techniques, a loss of >70% of the counts of INT-reducing microorganisms was shown to be due to the dissolution of INT-formazan deposits by immersion oil (used in microscopy). In addition, significantly fewer fluorescing microorganisms and INT-formazan deposits, both ≤0.2 μm in size, were found for sample preparations that included a Nuclepore filter. Visual clarity was enhanced, and significantly greater direct counts and counts of INT-reducing microorganisms were recognized by transferring microorganisms from a filter to a gelatin film on a cover glass, followed by coating the sample with additional gelatin to produce a transparent matrix. With this method, the number of INT-reducing microorganisms determined for a Chesapeake Bay water sample was 2-to 10-fold greater than the number of respiring organisms reported previously for marine or freshwater samples. INT-reducing microorganisms constituted 61% of the total direct counts determined for a Chesapeake Bay water sample. This is the highest percentage of metabolically active microorganisms of any aquatic population reported using a method which determines both total counts and specific activity. PMID:16346025

Improved method for determination of respiring individual microorganisms in natural waters.

PubMed

Tabor, P S; Neihof, R A

1982-06-01

A method is reported that combines the microscopic determinations of specific, individual, respiring microorganisms by the detection of electron transport system activity and the total number of organisms of an estuarine population by epifluorescence microscopy. An active cellular electron transport system specifically reduces 2-(p-iodophenyl)-3-(p-nitrophenyl)-5-phenyl tetrazolium chloride (INT) to INT-formazan, which is recognized as opaque intracellular deposits in microorganisms stained with acridine orange. In a comparison of previously described sample preparation techniques, a loss of >70% of the counts of INT-reducing microorganisms was shown to be due to the dissolution of INT-formazan deposits by immersion oil (used in microscopy). In addition, significantly fewer fluorescing microorganisms and INT-formazan deposits, both

COMPLEX VARIABLE BOUNDARY ELEMENT METHOD: APPLICATIONS.

USGS Publications Warehouse

Hromadka, T.V.; Yen, C.C.; Guymon, G.L.

1985-01-01

The complex variable boundary element method (CVBEM) is used to approximate several potential problems where analytical solutions are known. A modeling result produced from the CVBEM is a measure of relative error in matching the known boundary condition values of the problem. A CVBEM error-reduction algorithm is used to reduce the relative error of the approximation by adding nodal points in boundary regions where error is large. From the test problems, overall error is reduced significantly by utilizing the adaptive integration algorithm.

Corruption costs lives: evidence from a cross-country study.

PubMed

Li, Qiang; An, Lian; Xu, Jing; Baliamoune-Lutz, Mina

2018-01-01

This paper investigates the effect of corruption on health outcomes by using cross-country panel data covering about 150 countries for the period of 1995 to 2012. We employ ordinary least squares (OLS), fixed-effects and two-stage least squares (2SLS) estimation methods, and find that corruption significantly increases mortality rates, and reduces life expectancy and immunization rates. The results are consistent across different regions, gender, and measures of corruption. The findings suggest that reducing corruption can be an effective method to improve health outcomes.

A method for simplifying the analysis of traffic accidents injury severity on two-lane highways using Bayesian networks.

PubMed

Mujalli, Randa Oqab; de Oña, Juan

2011-10-01

This study describes a method for reducing the number of variables frequently considered in modeling the severity of traffic accidents. The method's efficiency is assessed by constructing Bayesian networks (BN). It is based on a two stage selection process. Several variable selection algorithms, commonly used in data mining, are applied in order to select subsets of variables. BNs are built using the selected subsets and their performance is compared with the original BN (with all the variables) using five indicators. The BNs that improve the indicators' values are further analyzed for identifying the most significant variables (accident type, age, atmospheric factors, gender, lighting, number of injured, and occupant involved). A new BN is built using these variables, where the results of the indicators indicate, in most of the cases, a statistically significant improvement with respect to the original BN. It is possible to reduce the number of variables used to model traffic accidents injury severity through BNs without reducing the performance of the model. The study provides the safety analysts a methodology that could be used to minimize the number of variables used in order to determine efficiently the injury severity of traffic accidents without reducing the performance of the model. Copyright © 2011 Elsevier Ltd. All rights reserved.

Combination of ray-tracing and the method of moments for electromagnetic radiation analysis using reduced meshes

NASA Astrophysics Data System (ADS)

Delgado, Carlos; Cátedra, Manuel Felipe

2018-05-01

This work presents a technique that allows a very noticeable relaxation of the computational requirements for full-wave electromagnetic simulations based on the Method of Moments. A ray-tracing analysis of the geometry is performed in order to extract the critical points with significant contributions. These points are then used to generate a reduced mesh, considering the regions of the geometry that surround each critical point and taking into account the electrical path followed from the source. The electromagnetic analysis of the reduced mesh produces very accurate results, requiring a fraction of the resources that the conventional analysis would utilize.

Model predictive control based on reduced order models applied to belt conveyor system.

PubMed

Chen, Wei; Li, Xin

2016-11-01

In the paper, a model predictive controller based on reduced order model is proposed to control belt conveyor system, which is an electro-mechanics complex system with long visco-elastic body. Firstly, in order to design low-degree controller, the balanced truncation method is used for belt conveyor model reduction. Secondly, MPC algorithm based on reduced order model for belt conveyor system is presented. Because of the error bound between the full-order model and reduced order model, two Kalman state estimators are applied in the control scheme to achieve better system performance. Finally, the simulation experiments are shown that balanced truncation method can significantly reduce the model order with high-accuracy and model predictive control based on reduced-model performs well in controlling the belt conveyor system. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

In vitro antioxidant and antihyperlipidemic activities of Bauhinia variegata Linn

PubMed Central

Rajani, G.P.; Ashok, Purnima

2009-01-01

Objectives: To evaluate the ethanolic and aqueous extracts of Bauhinia variegata Linn. for in vitro antioxidant and antihyperlipidemic activity. Materials and Methods: Ethanolic and aqueous extracts of the stem bark and root of B. variegata Linn. were prepared and assessed for in vitro antioxidant activity by various methods namely total reducing power, scavenging of various free radicals such as 1,2-diphenyl-2-picrylhydrazyl (DPPH), super oxide, nitric oxide, and hydrogen peroxide. The percentage scavenging of various free radicals were compared with standard antioxidants such as ascorbic acid and butylated hydroxyl anisole (BHA). The extracts were also evaluated for antihyperlipidemic activity in Triton WR-1339 (iso-octyl polyoxyethylene phenol)-induced hyperlipidemic albino rats by estimating serum triglyceride, very low density lipids (VLDL), cholesterol, low-density lipids (LDL), and high-density lipid (HDL) levels. Result: Significant antioxidant activity was observed in all the methods, (P < 0.01) for reducing power and (P < 0.001) for scavenging DPPH, super oxide, nitric oxide, and hydrogen peroxide radicals. The extracts showed significant reduction (P < 0.01) in cholesterol at 6 and 24 h and (P < 0.05) at 48 h. There was significant reduction (P < 0.01) in triglyceride level at 6, 24, and 48 h. The VLDL level was also significantly (P < 0.05) reduced from 24 h and maximum reduction (P < 0.01) was seen at 48 h. There was significant increase (P < 0.01) in HDL at 6, 24, and 48 h. Conclusion: From the results, it is evident that alcoholic and aqueous extracts of B. variegata Linn. can effectively decrease plasma cholesterol, triglyceride, LDL, and VLDL and increase plasma HDL levels. In addition, the alcoholic and aqueous extracts have shown significant antioxidant activity. By the virtue of its antioxidant activity, B. variegata Linn. may show antihyperlipidemic activity. PMID:20177495

Novel Thermally Stable Poly (vinyl chloride) Composites for Sulfate Removal

EPA Science Inventory

BaCO₃ dispersed PVC composites were prepared through a polymer re-precipitation method. The composites were tested for sulfate removal using rapid small scale column test (RSSCT) and found to significantly reduce sulfate concentration. The method was extended to synthe...

New Hybrid Algorithms for Estimating Tree Stem Diameters at Breast Height Using a Two Dimensional Terrestrial Laser Scanner

PubMed Central

Kong, Jianlei; Ding, Xiaokang; Liu, Jinhao; Yan, Lei; Wang, Jianli

2015-01-01

In this paper, a new algorithm to improve the accuracy of estimating diameter at breast height (DBH) for tree trunks in forest areas is proposed. First, the information is collected by a two-dimensional terrestrial laser scanner (2DTLS), which emits laser pulses to generate a point cloud. After extraction and filtration, the laser point clusters of the trunks are obtained, which are optimized by an arithmetic means method. Then, an algebraic circle fitting algorithm in polar form is non-linearly optimized by the Levenberg-Marquardt method to form a new hybrid algorithm, which is used to acquire the diameters and positions of the trees. Compared with previous works, this proposed method improves the accuracy of diameter estimation of trees significantly and effectively reduces the calculation time. Moreover, the experimental results indicate that this method is stable and suitable for the most challenging conditions, which has practical significance in improving the operating efficiency of forest harvester and reducing the risk of causing accidents. PMID:26147726

Coordinate alignment of combined measurement systems using a modified common points method

NASA Astrophysics Data System (ADS)

Zhao, G.; Zhang, P.; Xiao, W.

2018-03-01

The co-ordinate metrology has been extensively researched for its outstanding advantages in measurement range and accuracy. The alignment of different measurement systems is usually achieved by integrating local coordinates via common points before measurement. The alignment errors would accumulate and significantly reduce the global accuracy, thus need to be minimized. In this thesis, a modified common points method (MCPM) is proposed to combine different traceable system errors of the cooperating machines, and optimize the global accuracy by introducing mutual geometric constraints. The geometric constraints, obtained by measuring the common points in individual local coordinate systems, provide the possibility to reduce the local measuring uncertainty whereby enhance the global measuring certainty. A simulation system is developed in Matlab to analyze the feature of MCPM using the Monto-Carlo method. An exemplary setup is constructed to verify the feasibility and efficiency of the proposed method associated with laser tracker and indoor iGPS systems. Experimental results show that MCPM could significantly improve the alignment accuracy.

An Analytical Solution for Yaw Maneuver Optimization on the International Space Station and Other Orbiting Space Vehicles

NASA Technical Reports Server (NTRS)

Dobrinskaya, Tatiana

2015-01-01

This paper suggests a new method for optimizing yaw maneuvers on the International Space Station (ISS). Yaw rotations are the most common large maneuvers on the ISS often used for docking and undocking operations, as well as for other activities. When maneuver optimization is used, large maneuvers, which were performed on thrusters, could be performed either using control moment gyroscopes (CMG), or with significantly reduced thruster firings. Maneuver optimization helps to save expensive propellant and reduce structural loads - an important factor for the ISS service life. In addition, optimized maneuvers reduce contamination of the critical elements of the vehicle structure, such as solar arrays. This paper presents an analytical solution for optimizing yaw attitude maneuvers. Equations describing pitch and roll motion needed to counteract the major torques during a yaw maneuver are obtained. A yaw rate profile is proposed. Also the paper describes the physical basis of the suggested optimization approach. In the obtained optimized case, the torques are significantly reduced. This torque reduction was compared to the existing optimization method which utilizes the computational solution. It was shown that the attitude profiles and the torque reduction have a good match for these two methods of optimization. The simulations using the ISS flight software showed similar propellant consumption for both methods. The analytical solution proposed in this paper has major benefits with respect to computational approach. In contrast to the current computational solution, which only can be calculated on the ground, the analytical solution does not require extensive computational resources, and can be implemented in the onboard software, thus, making the maneuver execution automatic. The automatic maneuver significantly simplifies the operations and, if necessary, allows to perform a maneuver without communication with the ground. It also reduces the probability of command errors. The suggested analytical solution provides a new method of maneuver optimization which is less complicated, automatic and more universal. A maneuver optimization approach, presented in this paper, can be used not only for the ISS, but for other orbiting space vehicles.

Recent progress on improving ICRF coupling and reducing RF-specific impurities in ASDEX Upgrade

NASA Astrophysics Data System (ADS)

Zhang, Wei; Bobkov, Volodymyr; Noterdaeme, Jean-Marie; Tierens, Wouter; Aguiam, Diogo; Bilato, Roberto; Coster, David; Colas, Laurent; Crombé, Kristel; Fuenfgelder, Helmut; Faugel, Helmut; Feng, Yuhe; Jacquot, Jonathan; Jacquet, Philippe; Kallenbach, Arne; Kostic, Ana; Lunt, Tilmann; Maggiora, Riccardo; Ochoukov, Roman; Silva, Antonio; Suárez, Guillermo; Tuccilo, Angelo A.; Tudisco, Onofrio; Usoltceva, Mariia; Van Eester, Dirk; Wang, Yongsheng; Yang, Qingxi

2017-10-01

The recent scientific research on ASDEX Upgrade (AUG) has greatly advanced solutions to two issues of Radio Frequency (RF) heating in the Ion Cyclotron Range of Frequencies (ICRF): (a) the coupling of ICRF power to the plasma is significantly improved by density tailoring with local gas puffing; (b) the release of RF-specific impurities is significantly reduced by minimizing the RF near field with 3-strap antennas. This paper summarizes the applied methods and reviews the associated achievements.

Improving the numerical integration solution of satellite orbits in the presence of solar radiation pressure using modified back differences

NASA Technical Reports Server (NTRS)

Lundberg, J. B.; Feulner, M. R.; Abusali, P. A. M.; Ho, C. S.

1991-01-01

The method of modified back differences, a technique that significantly reduces the numerical integration errors associated with crossing shadow boundaries using a fixed-mesh multistep integrator without a significant increase in computer run time, is presented. While Hubbard's integral approach can produce significant improvements to the trajectory solution, the interpolation method provides the best overall results. It is demonstrated that iterating on the point mass term correction is also important for achieving the best overall results. It is also shown that the method of modified back differences can be implemented with only a small increase in execution time.

Insulator coated magnetic nanoparticulate composites with reduced core loss and method of manufacture thereof

NASA Technical Reports Server (NTRS)

Zhang, Yide (Inventor); Wang, Shihe (Inventor); Xiao, Danny (Inventor)

2004-01-01

A series of bulk-size magnetic/insulating nanostructured composite soft magnetic materials with significantly reduced core loss and its manufacturing technology. This insulator coated magnetic nanostructured composite is comprises a magnetic constituent, which contains one or more magnetic components, and an insulating constituent. The magnetic constituent is nanometer scale particles (1-100 nm) coated by a thin-layered insulating phase (continuous phase). While the intergrain interaction between the immediate neighboring magnetic nanoparticles separated by the insulating phase (or coupled nanoparticles) provide the desired soft magnetic properties, the insulating material provides the much demanded high resistivity which significantly reduces the eddy current loss. The resulting material is a high performance magnetic nanostructured composite with reduced core loss.

Reducing statistical uncertainties in simulated organ doses of phantoms immersed in water

DOE PAGES

Hiller, Mauritius M.; Veinot, Kenneth G.; Easterly, Clay E.; ...

2016-08-13

In this study, methods are addressed to reduce the computational time to compute organ-dose rate coefficients using Monte Carlo techniques. Several variance reduction techniques are compared including the reciprocity method, importance sampling, weight windows and the use of the ADVANTG software package. For low-energy photons, the runtime was reduced by a factor of 10 5 when using the reciprocity method for kerma computation for immersion of a phantom in contaminated water. This is particularly significant since impractically long simulation times are required to achieve reasonable statistical uncertainties in organ dose for low-energy photons in this source medium and geometry. Althoughmore » the MCNP Monte Carlo code is used in this paper, the reciprocity technique can be used equally well with other Monte Carlo codes.« less

Reduction of the sonic boom level in supersonic aircraft flight by the method of surface cooling

NASA Astrophysics Data System (ADS)

Fomin, V. M.; Chirkashenko, V. F.; Volkov, V. F.; Kharitonov, A. M.

2013-12-01

Based on the analysis of various aspects of creating a supersonic transport aircraft of the second generation, the necessity of developing unconventional active methods of sonic boom level reduction is demonstrated. Surface cooling is shown to exert a significant effect on formation of the disturbed flow structure up to large distances from the body by an example of a supersonic flow around a body of revolution. A method of reducing the intensity of the intermediate shock wave and excess pressure momentum near the body is proposed. This method allows the length of the reduced (by 50%) sonic boom level to be increased and the bow shock wave intensity in the far zone to be reduced by 12%. A possibility of controlling the process of formation of wave structures, such as hanging pressure shocks arising near the aircraft surface, is demonstrated. The action of the cryogenic mechanism is explained.

Multilevel metallization method for fabricating a metal oxide semiconductor device

NASA Technical Reports Server (NTRS)

Hollis, B. R., Jr.; Feltner, W. R.; Bouldin, D. L.; Routh, D. E. (Inventor)

1978-01-01

An improved method is described of constructing a metal oxide semiconductor device having multiple layers of metal deposited by dc magnetron sputtering at low dc voltages and low substrate temperatures. The method provides multilevel interconnections and cross over between individual circuit elements in integrated circuits without significantly reducing the reliability or seriously affecting the yield.

Reducing health risk assigned to organic emissions from a chemical weapons incinerator.

PubMed

Laman, David M; Weiler, B Douglas; Skeen, Rodney S

2013-03-01

Organic emissions from a chemical weapons incinerator have been characterized with an improved set of analytical methods to reduce the human health risk assigned to operations of the facility. A gas chromatography/mass selective detection method with substantially reduced detection limits has been used in conjunction with scanning electron microscopy/energy dispersive X-ray spectrometry and Fourier transform infrared microscopy to improve the speciation of semi-volatile and non-volatile organics emitted from the incinerator. The reduced detection limits have allowed a significant reduction in the assumed polycyclic aromatic hydrocarbon (PAH) and aminobiphenyl (ABP) emission rates used as inputs to the human health risk assessment for the incinerator. A mean factor of 17 decrease in assigned human health risk is realized for six common local exposure scenarios as a result of the reduced PAH and ABP detection limits.

Application of the Finite Element Method to Rotary Wing Aeroelasticity

NASA Technical Reports Server (NTRS)

Straub, F. K.; Friedmann, P. P.

1982-01-01

A finite element method for the spatial discretization of the dynamic equations of equilibrium governing rotary-wing aeroelastic problems is presented. Formulation of the finite element equations is based on weighted Galerkin residuals. This Galerkin finite element method reduces algebraic manipulative labor significantly, when compared to the application of the global Galerkin method in similar problems. The coupled flap-lag aeroelastic stability boundaries of hingeless helicopter rotor blades in hover are calculated. The linearized dynamic equations are reduced to the standard eigenvalue problem from which the aeroelastic stability boundaries are obtained. The convergence properties of the Galerkin finite element method are studied numerically by refining the discretization process. Results indicate that four or five elements suffice to capture the dynamics of the blade with the same accuracy as the global Galerkin method.

Comparison of 3 Methods for Identifying Dietary Patterns Associated With Risk of Disease

PubMed Central

DiBello, Julia R.; Kraft, Peter; McGarvey, Stephen T.; Goldberg, Robert; Campos, Hannia

2008-01-01

Reduced rank regression and partial least-squares regression (PLS) are proposed alternatives to principal component analysis (PCA). Using all 3 methods, the authors derived dietary patterns in Costa Rican data collected on 3,574 cases and controls in 1994–2004 and related the resulting patterns to risk of first incident myocardial infarction. Four dietary patterns associated with myocardial infarction were identified. Factor 1, characterized by high intakes of lean chicken, vegetables, fruit, and polyunsaturated oil, was generated by all 3 dietary pattern methods and was associated with a significantly decreased adjusted risk of myocardial infarction (28%–46%, depending on the method used). PCA and PLS also each yielded a pattern associated with a significantly decreased risk of myocardial infarction (31% and 23%, respectively); this pattern was characterized by moderate intake of alcohol and polyunsaturated oil and low intake of high-fat dairy products. The fourth factor derived from PCA was significantly associated with a 38% increased risk of myocardial infarction and was characterized by high intakes of coffee and palm oil. Contrary to previous studies, the authors found PCA and PLS to produce more patterns associated with cardiovascular disease than reduced rank regression. The most effective method for deriving dietary patterns related to disease may vary depending on the study goals. PMID:18945692

CO2 and CH4 fluxes in a Spartina salt marsh and brackish Phragmites marsh in Massachusetts

NASA Astrophysics Data System (ADS)

Tang, J.; Wang, F.; Kroeger, K. D.; Gonneea, M. E.

2017-12-01

Coastal salt marshes play an important role in global and regional carbon cycling. Tidally restricted marshes reduce salinity and provide a habitat suitable for Phragmites invasion. We measured greenhouse gas (GHG) emissions (CO2 and CH4) continuously with the eddy covariance method and biweekly with the static chamber method in a Spartina salt marsh and a Phragmites marsh on Cape Cod, Massachusetts, USA. We did not find significant difference in CO2 fluxes between the two sites, but the CH4 fluxes were much higher in the Phragmites site than the Spartina marsh. Temporally, tidal cycles influence the CO2 and CH4 fluxes in both sites. We found that the salt marsh was a significant carbon sink when CO2 and CH4 fluxes were combined. Restoring tidally restricted marshes will significantly reduce CH4 emissions and provide a strong ecosystem carbon service.

Effect of a triclosan/PVM/MA copolymer/fluoride dentifrice on volatile sulfur compounds in vitro.

PubMed

Pilch, S; Williams, M I; Cummins, D

2005-01-01

The objective of the investigation was to document the in vitro efficacy of a triclosan/PVM/MA copolymer/fluoride (TCF) dentifrice against the formation of volatile sulfur compounds (VSC) as well as the growth of H2S-producing bacteria. Clinical studies using organoleptic judges, gas chromatography, or a portable sulfide monitor have generally been employed in the assessment of treatments for the control of oral malodor. However, these studies are not appropriate for screening purposes because of the expense and time required. An in vitro method was developed for the purpose of screening new compounds, agents or formulations for their ability to control VSC formation and for determining bio-equivalence of efficacy when implementing changes in existing formulations. The method combines basic microbiological methods, dynamic flow cell techniques and head space analysis. The in vitro VSC method was validated by comparing the efficacy of two dentifrices containing TCF with a control fluoride dentifrice as the TCF products have been clinically proven to control oral malodor. In the validation studies, the TCF-containing dentifrices were significantly better (P < 0.05) than the control dentifrice in inhibiting VSC formation and reducing H(2)S-producing bacteria. For example, when compared with baseline, the TCF dentifrices reduced VSC formation between 42 and 49% compared with the control dentifrice which reduced VSC formation 3%. There was no significant difference (P > 0.05) between the two TCF dentifrice formulations. Using an in vitro breath VSC model, it has been demonstrated that two variants of a dentifrice containing triclosan, PVM/MA copolymer and fluoride have efficacy that is significantly better than a control fluoridated dentifrice and that there is no significant difference between the triclosan/PVM/MA copolymer/fluoride dentifrice variants.

Dynamically Hedging Oil and Currency Futures Using Receding Horizontal Control and Stochastic Programming

NASA Astrophysics Data System (ADS)

Cottrell, Paul Edward

There is a lack of research in the area of hedging future contracts, especially in illiquid or very volatile market conditions. It is important to understand the volatility of the oil and currency markets because reduced fluctuations in these markets could lead to better hedging performance. This study compared different hedging methods by using a hedging error metric, supplementing the Receding Horizontal Control and Stochastic Programming (RHCSP) method by utilizing the London Interbank Offered Rate with the Levy process. The RHCSP hedging method was investigated to determine if improved hedging error was accomplished compared to the Black-Scholes, Leland, and Whalley and Wilmott methods when applied on simulated, oil, and currency futures markets. A modified RHCSP method was also investigated to determine if this method could significantly reduce hedging error under extreme market illiquidity conditions when applied on simulated, oil, and currency futures markets. This quantitative study used chaos theory and emergence for its theoretical foundation. An experimental research method was utilized for this study with a sample size of 506 hedging errors pertaining to historical and simulation data. The historical data were from January 1, 2005 through December 31, 2012. The modified RHCSP method was found to significantly reduce hedging error for the oil and currency market futures by the use of a 2-way ANOVA with a t test and post hoc Tukey test. This study promotes positive social change by identifying better risk controls for investment portfolios and illustrating how to benefit from high volatility in markets. Economists, professional investment managers, and independent investors could benefit from the findings of this study.

An improved protocol for the preparation of total genomic DNA from isolates of yeast and mould using Whatman FTA filter papers.

PubMed

Borman, Andrew M; Fraser, Mark; Linton, Christopher J; Palmer, Michael D; Johnson, Elizabeth M

2010-06-01

Here, we present a significantly improved version of our previously published method for the extraction of fungal genomic DNA from pure cultures using Whatman FTA filter paper matrix technology. This modified protocol is extremely rapid, significantly more cost effective than our original method, and importantly, substantially reduces the problem of potential cross-contamination between sequential filters when employing FTA technology.

Iterative Boltzmann plot method for temperature and pressure determination in a xenon high pressure discharge lamp

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zalach, J.; Franke, St.

2013-01-28

The Boltzmann plot method allows to calculate plasma temperatures and pressures if absolutely calibrated emission coefficients of spectral lines are available. However, xenon arcs are not very well suited to be analyzed this way, as there are only a limited number of lines with atomic data available. These lines have high excitation energies in a small interval between 9.8 and 11.5 eV. Uncertainties in the experimental method and in the atomic data further limit the accuracy of the evaluation procedure. This may result in implausible values of temperature and pressure with inadmissible uncertainty. To omit these shortcomings, an iterative schememore » is proposed that is making use of additional information about the xenon fill pressure. This method is proved to be robust against noisy data and significantly reduces the uncertainties. Intentionally distorted synthetic data are used to illustrate the performance of the method, and measurements performed on a laboratory xenon high pressure discharge lamp are analyzed resulting in reasonable temperatures and pressures with significantly reduced uncertainties.« less

Design and control of the phase current of a brushless dc motor to eliminate cogging torque

NASA Astrophysics Data System (ADS)

Jang, G. H.; Lee, C. J.

2006-04-01

This paper presents a design and control method of the phase current to reduce the torque ripple of a brushless dc (BLDC) motor by eliminating cogging torque. The cogging torque is the main source of torque ripple and consequently of speed error, and it is also the excitation source to generate the vibration and noise of a motor. This research proposes a modified current wave form, which is composed of main and auxiliary currents. The former is the conventional current to generate the commutating torque. The latter generates the torque with the same magnitude and opposite sign of the corresponding cogging torque at the given position in order to eliminate the cogging torque. Time-stepping finite element method simulation considering pulse-width-modulation switching method has been performed to verify the effectiveness of the proposed method, and it shows that this proposed method reduces torque ripple by 36%. A digital-signal-processor-based controller is also developed to implement the proposed method, and it shows that this proposed method reduces the speed ripple significantly.

Myocardial perfusion MRI with sliding-window conjugate-gradient HYPR.

PubMed

Ge, Lan; Kino, Aya; Griswold, Mark; Mistretta, Charles; Carr, James C; Li, Debiao

2009-10-01

First-pass perfusion MRI is a promising technique for detecting ischemic heart disease. However, the diagnostic value of the method is limited by the low spatial coverage, resolution, signal-to-noise ratio (SNR), and cardiac motion-related image artifacts. In this study we investigated the feasibility of using a method that combines sliding window and CG-HYPR methods (SW-CG-HYPR) to reduce the acquisition window for each slice while maintaining the temporal resolution of one frame per heartbeat in myocardial perfusion MRI. This method allows an increased number of slices, reduced motion artifacts, and preserves the relatively high SNR and spatial resolution of the "composite images." Results from eight volunteers demonstrate the feasibility of SW-CG-HYPR for accelerated myocardial perfusion imaging with accurate signal intensity changes of left ventricle blood pool and myocardium. Using this method the acquisition time per cardiac cycle was reduced by a factor of 4 and the number of slices was increased from 3 to 8 as compared to the conventional technique. The SNR of the myocardium at peak enhancement with SW-CG-HYPR (13.83 +/- 2.60) was significantly higher (P < 0.05) than the conventional turbo-FLASH protocol (8.40 +/- 1.62). Also, the spatial resolution of the myocardial perfection images was significantly improved. SW-CG-HYPR is a promising technique for myocardial perfusion MRI. (c) 2009 Wiley-Liss, Inc.

Determining Reduced Order Models for Optimal Stochastic Reduced Order Models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bonney, Matthew S.; Brake, Matthew R.W.

2015-08-01

The use of parameterized reduced order models(PROMs) within the stochastic reduced order model (SROM) framework is a logical progression for both methods. In this report, five different parameterized reduced order models are selected and critiqued against the other models along with truth model for the example of the Brake-Reuss beam. The models are: a Taylor series using finite difference, a proper orthogonal decomposition of the the output, a Craig-Bampton representation of the model, a method that uses Hyper-Dual numbers to determine the sensitivities, and a Meta-Model method that uses the Hyper-Dual results and constructs a polynomial curve to better representmore » the output data. The methods are compared against a parameter sweep and a distribution propagation where the first four statistical moments are used as a comparison. Each method produces very accurate results with the Craig-Bampton reduction having the least accurate results. The models are also compared based on time requirements for the evaluation of each model where the Meta- Model requires the least amount of time for computation by a significant amount. Each of the five models provided accurate results in a reasonable time frame. The determination of which model to use is dependent on the availability of the high-fidelity model and how many evaluations can be performed. Analysis of the output distribution is examined by using a large Monte-Carlo simulation along with a reduced simulation using Latin Hypercube and the stochastic reduced order model sampling technique. Both techniques produced accurate results. The stochastic reduced order modeling technique produced less error when compared to an exhaustive sampling for the majority of methods.« less

Continuous correction of differential path length factor in near-infrared spectroscopy

PubMed Central

Moore, Jason H.; Diamond, Solomon G.

2013-01-01

Abstract. In continuous-wave near-infrared spectroscopy (CW-NIRS), changes in the concentration of oxyhemoglobin and deoxyhemoglobin can be calculated by solving a set of linear equations from the modified Beer-Lambert Law. Cross-talk error in the calculated hemodynamics can arise from inaccurate knowledge of the wavelength-dependent differential path length factor (DPF). We apply the extended Kalman filter (EKF) with a dynamical systems model to calculate relative concentration changes in oxy- and deoxyhemoglobin while simultaneously estimating relative changes in DPF. Results from simulated and experimental CW-NIRS data are compared with results from a weighted least squares (WLSQ) method. The EKF method was found to effectively correct for artificially introduced errors in DPF and to reduce the cross-talk error in simulation. With experimental CW-NIRS data, the hemodynamic estimates from EKF differ significantly from the WLSQ (p<0.001). The cross-correlations among residuals at different wavelengths were found to be significantly reduced by the EKF method compared to WLSQ in three physiologically relevant spectral bands 0.04 to 0.15 Hz, 0.15 to 0.4 Hz and 0.4 to 2.0 Hz (p<0.001). This observed reduction in residual cross-correlation is consistent with reduced cross-talk error in the hemodynamic estimates from the proposed EKF method. PMID:23640027

Continuous correction of differential path length factor in near-infrared spectroscopy

NASA Astrophysics Data System (ADS)

Talukdar, Tanveer; Moore, Jason H.; Diamond, Solomon G.

2013-05-01

In continuous-wave near-infrared spectroscopy (CW-NIRS), changes in the concentration of oxyhemoglobin and deoxyhemoglobin can be calculated by solving a set of linear equations from the modified Beer-Lambert Law. Cross-talk error in the calculated hemodynamics can arise from inaccurate knowledge of the wavelength-dependent differential path length factor (DPF). We apply the extended Kalman filter (EKF) with a dynamical systems model to calculate relative concentration changes in oxy- and deoxyhemoglobin while simultaneously estimating relative changes in DPF. Results from simulated and experimental CW-NIRS data are compared with results from a weighted least squares (WLSQ) method. The EKF method was found to effectively correct for artificially introduced errors in DPF and to reduce the cross-talk error in simulation. With experimental CW-NIRS data, the hemodynamic estimates from EKF differ significantly from the WLSQ (p<0.001). The cross-correlations among residuals at different wavelengths were found to be significantly reduced by the EKF method compared to WLSQ in three physiologically relevant spectral bands 0.04 to 0.15 Hz, 0.15 to 0.4 Hz and 0.4 to 2.0 Hz (p<0.001). This observed reduction in residual cross-correlation is consistent with reduced cross-talk error in the hemodynamic estimates from the proposed EKF method.

Assessment of alternative disposal methods to reduce greenhouse gas emissions from municipal solid waste in India.

PubMed

Yedla, Sudhakar; Sindhu, N T

2016-06-01

Open dumping, the most commonly practiced method of solid waste disposal in Indian cities, creates serious environment and economic challenges, and also contributes significantly to greenhouse gas emissions. The present article attempts to analyse and identify economically effective ways to reduce greenhouse gas emissions from municipal solid waste. The article looks at the selection of appropriate methods for the control of methane emissions. Multivariate functional models are presented, based on theoretical considerations as well as the field measurements to forecast the greenhouse gas mitigation potential for all the methodologies under consideration. Economic feasibility is tested by calculating the unit cost of waste disposal for the respective disposal process. The purpose-built landfill system proposed by Yedla and Parikh has shown promise in controlling greenhouse gas and saving land. However, these studies show that aerobic composting offers the optimal method, both in terms of controlling greenhouse gas emissions and reducing costs, mainly by requiring less land than other methods. © The Author(s) 2016.

Efficacy of a Radiation Absorbing Shield in Reducing Dose to the Interventionalist During Peripheral Endovascular Procedures: A Single Centre Pilot Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Power, S.; Mirza, M.; Thakorlal, A.

PurposeThis prospective pilot study was undertaken to evaluate the feasibility and effectiveness of using a radiation absorbing shield to reduce operator dose from scatter during lower limb endovascular procedures.Materials and MethodsA commercially available bismuth shield system (RADPAD) was used. Sixty consecutive patients undergoing lower limb angioplasty were included. Thirty procedures were performed without the RADPAD (control group) and thirty with the RADPAD (study group). Two separate methods were used to measure dose to a single operator. Thermoluminescent dosimeter (TLD) badges were used to measure hand, eye, and unshielded body dose. A direct dosimeter with digital readout was also used tomore » measure eye and unshielded body dose. To allow for variation between control and study groups, dose per unit time was calculated.ResultsTLD results demonstrated a significant reduction in median body dose per unit time for the study group compared with controls (p = 0.001), corresponding to a mean dose reduction rate of 65 %. Median eye and hand dose per unit time were also reduced in the study group compared with control group, however, this was not statistically significant (p = 0.081 for eye, p = 0.628 for hand). Direct dosimeter readings also showed statistically significant reduction in median unshielded body dose rate for the study group compared with controls (p = 0.037). Eye dose rate was reduced for the study group but this was not statistically significant (p = 0.142).ConclusionInitial results are encouraging. Use of the shield resulted in a statistically significant reduction in unshielded dose to the operator’s body. Measured dose to the eye and hand of operator were also reduced but did not reach statistical significance in this pilot study.« less

The feasibility of using computer graphics in environmental evaluations : interim report, documenting historic site locations using computer graphics.

DOT National Transportation Integrated Search

1981-01-01

This report describes a method for locating historic site information using a computer graphics program. If adopted for use by the Virginia Department of Highways and Transportation, this method should significantly reduce the time now required to de...

Systematic Desensitization as a Method of Teaching a General Anxiety-Reducing Skill

ERIC Educational Resources Information Center

Zemore, Robert

1975-01-01

College students were treated with either a standard or modified version of systematic desensitization. Relative to a no-treatment control group, both treatment methods produced significant reductions in both the treated and untreated fears. The implications these findings have for two alternative conceptions of systematic desensitization are…

[Optimized application of nested PCR method for detection of malaria].

PubMed

Yao-Guang, Z; Li, J; Zhen-Yu, W; Li, C

2017-04-28

Objective To optimize the application of the nested PCR method for the detection of malaria according to the working practice, so as to improve the efficiency of malaria detection. Methods Premixing solution of PCR, internal primers for further amplification and new designed primers that aimed at two Plasmodium ovale subspecies were employed to optimize the reaction system, reaction condition and specific primers of P . ovale on basis of routine nested PCR. Then the specificity and the sensitivity of the optimized method were analyzed. The positive blood samples and examination samples of malaria were detected by the routine nested PCR and the optimized method simultaneously, and the detection results were compared and analyzed. Results The optimized method showed good specificity, and its sensitivity could reach the pg to fg level. The two methods were used to detect the same positive malarial blood samples simultaneously, the results indicated that the PCR products of the two methods had no significant difference, but the non-specific amplification reduced obviously and the detection rates of P . ovale subspecies improved, as well as the total specificity also increased through the use of the optimized method. The actual detection results of 111 cases of malarial blood samples showed that the sensitivity and specificity of the routine nested PCR were 94.57% and 86.96%, respectively, and those of the optimized method were both 93.48%, and there was no statistically significant difference between the two methods in the sensitivity ( P > 0.05), but there was a statistically significant difference between the two methods in the specificity ( P < 0.05). Conclusion The optimized PCR can improve the specificity without reducing the sensitivity on the basis of the routine nested PCR, it also can save the cost and increase the efficiency of malaria detection as less experiment links.

Does counselling improve uptake of long-term and permanent contraceptive methods in a high HIV-prevalence setting?

PubMed Central

Dudley, Lilian; Makumucha, Courage; Dlamini, Phatisizwe; Moyo, Sihle; Bhembe, Sibongiseni

2015-01-01

Abstract Background Studies have shown a reduced uptake of contraceptive methods in HIV-positive women of childbearing age, mainly because of unmet needs that may be a result of poor promotion of available methods of contraception, especially long-term and permanent methods (LTPM). Aim To compare the uptake of contraceptive methods, and particularly LTPM, by HIV-positive and HIV-negative post-partum mothers, and to assess the effects of counselling on contraceptive choices. Setting Three government district hospitals in Swaziland. Methods Interviews were conducted using a structured questionnaire, before and after counselling HIV-negative and HIV-positive post-partum women in LTPM use, unintended pregnancy rates, future fertility and reasons for contraceptive choices. Results A total of 711 women, of whom half were HIV-positive, participated in the study. Most (72.3% HIV-negative and 84% HIV-positive) were on modern methods of contraception, with the majority using 2-monthly and 3-monthly injectables. Intended use of any contraceptive increased to 99% after counselling. LTPM use was 7.0% in HIV-negative mothers and 15.3% in HIV-positive mothers before counselling, compared with 41.3% and 42.4% in HIV-negative and HIV-positive mothers, respectively, after counselling. Pregnancy intentions and counselling on future fertility were significantly associated with current use of contraception, whilst current LTPM use and level of education were significantly associated with LTPM post-counselling. Conclusion Counselling on all methods including LTPM reduced unmet needs in contraception in HIV-positive and HIV-negative mothers and could improve contraceptive uptake and reduce unintended pregnancies. Health workers do not always remember to include LTPM when they counsel clients, which could result in a low uptake of these methods. Further experimental studies should be conducted to validate these results. PMID:26842525

Fast Video Encryption Using the H.264 Error Propagation Property for Smart Mobile Devices

PubMed Central

Chung, Yongwha; Lee, Sungju; Jeon, Taewoong; Park, Daihee

2015-01-01

In transmitting video data securely over Video Sensor Networks (VSNs), since mobile handheld devices have limited resources in terms of processor clock speed and battery size, it is necessary to develop an efficient method to encrypt video data to meet the increasing demand for secure connections. Selective encryption methods can reduce the amount of computation needed while satisfying high-level security requirements. This is achieved by selecting an important part of the video data and encrypting it. In this paper, to ensure format compliance and security, we propose a special encryption method for H.264, which encrypts only the DC/ACs of I-macroblocks and the motion vectors of P-macroblocks. In particular, the proposed new selective encryption method exploits the error propagation property in an H.264 decoder and improves the collective performance by analyzing the tradeoff between the visual security level and the processing speed compared to typical selective encryption methods (i.e., I-frame, P-frame encryption, and combined I-/P-frame encryption). Experimental results show that the proposed method can significantly reduce the encryption workload without any significant degradation of visual security. PMID:25850068

Use of insecticide-treated house screens to reduce infestations of dengue virus vectors, Mexico.

PubMed

Manrique-Saide, Pablo; Che-Mendoza, Azael; Barrera-Perez, Mario; Guillermo-May, Guillermo; Herrera-Bojorquez, Josue; Dzul-Manzanilla, Felipe; Gutierrez-Castro, Cipriano; Lenhart, Audrey; Vazquez-Prokopec, Gonzalo; Sommerfeld, Johannes; McCall, Philip J; Kroeger, Axel; Arredondo-Jimenez, Juan I

2015-02-01

Dengue prevention efforts rely on control of virus vectors. We investigated use of insecticide-treated screens permanently affixed to windows and doors in Mexico and found that the screens significantly reduced infestations of Aedes aegypti mosquitoes in treated houses. Our findings demonstrate the value of this method for dengue virus vector control.

Improving target coverage and organ-at-risk sparing in intensity-modulated radiotherapy for cervical oesophageal cancer using a simple optimisation method.

PubMed

Lu, Jia-Yang; Cheung, Michael Lok-Man; Huang, Bao-Tian; Wu, Li-Li; Xie, Wen-Jia; Chen, Zhi-Jian; Li, De-Rui; Xie, Liang-Xi

2015-01-01

To assess the performance of a simple optimisation method for improving target coverage and organ-at-risk (OAR) sparing in intensity-modulated radiotherapy (IMRT) for cervical oesophageal cancer. For 20 selected patients, clinically acceptable original IMRT plans (Original plans) were created, and two optimisation methods were adopted to improve the plans: 1) a base dose function (BDF)-based method, in which the treatment plans were re-optimised based on the original plans, and 2) a dose-controlling structure (DCS)-based method, in which the original plans were re-optimised by assigning additional constraints for hot and cold spots. The Original, BDF-based and DCS-based plans were compared with regard to target dose homogeneity, conformity, OAR sparing, planning time and monitor units (MUs). Dosimetric verifications were performed and delivery times were recorded for the BDF-based and DCS-based plans. The BDF-based plans provided significantly superior dose homogeneity and conformity compared with both the DCS-based and Original plans. The BDF-based method further reduced the doses delivered to the OARs by approximately 1-3%. The re-optimisation time was reduced by approximately 28%, but the MUs and delivery time were slightly increased. All verification tests were passed and no significant differences were found. The BDF-based method for the optimisation of IMRT for cervical oesophageal cancer can achieve significantly better dose distributions with better planning efficiency at the expense of slightly more MUs.

Hierarchical matrices implemented into the boundary integral approaches for gravity field modelling

NASA Astrophysics Data System (ADS)

Čunderlík, Róbert; Vipiana, Francesca

2017-04-01

Boundary integral approaches applied for gravity field modelling have been recently developed to solve the geodetic boundary value problems numerically, or to process satellite observations, e.g. from the GOCE satellite mission. In order to obtain numerical solutions of "cm-level" accuracy, such approaches require very refined level of the disretization or resolution. This leads to enormous memory requirements that need to be reduced. An implementation of the Hierarchical Matrices (H-matrices) can significantly reduce a numerical complexity of these approaches. A main idea of the H-matrices is based on an approximation of the entire system matrix that is split into a family of submatrices. Large submatrices are stored in factorized representation, while small submatrices are stored in standard representation. This allows reducing memory requirements significantly while improving the efficiency. The poster presents our preliminary results of implementations of the H-matrices into the existing boundary integral approaches based on the boundary element method or the method of fundamental solution.

Service tough composite structures using the Z-direction reinforcement process

NASA Technical Reports Server (NTRS)

Freitas, Glenn; Magee, Constance; Boyce, Joseph; Bott, Richard

1992-01-01

Foster-Miller has developed a new process to provide through thickness reinforcement of composite structures. The process reinforces laminates locally or globally on-tool during standard autoclave processing cycles. Initial test results indicate that the method has the potential to significantly reduce delamination in carbon-epoxy. Laminates reinforced with the z-fiber process have demonstrated significant improvements in mode 1 fracture toughness and compression strength after impact. Unlike alternative methods, in-plane properties are not adversely affected.

[Effects of different straw recycling and tillage methods on soil respiration and microbial activity].

PubMed

Li, Xiao-sha; Wu, Ning; Liu, Ling; Feng, Yu-peng; Xu, Xu; Han, Hui-fang; Ning, Tang-yuan; Li, Zeng-jia

2015-06-01

To explore the effects of different tillage methods and straw recycling on soil respiration and microbial activity in summer maize field during the winter wheat and summer maize double cropping system, substrate induced respiration method and CO2 release method were used to determine soil microbial biomass carbon, microbial activity, soil respiration, and microbial respiratory quotient. The experiment included 3 tillage methods during the winter wheat growing season, i.e., no-tillage, subsoiling and conventional tillage. Each tillage method was companied with 2 straw management patterns, i.e., straw recycling and no straw. The results indicated that the conservation tillage methods and straw recycling mainly affected 0-10 cm soil layer. Straw recycling could significantly improve the microbial biomass carbon and microbial activity, while decrease microbial respiratory quotient. Straw recycling could improve the soil respiration at both seedling stage and anthesis, however, it could reduce the soil respiration at filling stage, wax ripeness, and harvest stage. Under the same straw application, compared with conventional tillage, the soil respiration and microbial respiratory quotient in both subsoiling and no-tillage were reduced, while the microbial biomass carbon and microbial activity were increased. During the summer maize growing season, soil microbial biomass carbon and microbial activity were increased in straw returning with conservation tillage, while the respiratory quotient was reduced. In 0-10 cm soil layer, compared with conventional tillage, straw recycling with subsoiling and no-tillage significantly increased soil microbial biomass carbon by 95.8% and 74.3%, and increased soil microbial activity by 97.1% and 74.2%, respectively.

Efficient pairwise RNA structure prediction using probabilistic alignment constraints in Dynalign

PubMed Central

2007-01-01

Background Joint alignment and secondary structure prediction of two RNA sequences can significantly improve the accuracy of the structural predictions. Methods addressing this problem, however, are forced to employ constraints that reduce computation by restricting the alignments and/or structures (i.e. folds) that are permissible. In this paper, a new methodology is presented for the purpose of establishing alignment constraints based on nucleotide alignment and insertion posterior probabilities. Using a hidden Markov model, posterior probabilities of alignment and insertion are computed for all possible pairings of nucleotide positions from the two sequences. These alignment and insertion posterior probabilities are additively combined to obtain probabilities of co-incidence for nucleotide position pairs. A suitable alignment constraint is obtained by thresholding the co-incidence probabilities. The constraint is integrated with Dynalign, a free energy minimization algorithm for joint alignment and secondary structure prediction. The resulting method is benchmarked against the previous version of Dynalign and against other programs for pairwise RNA structure prediction. Results The proposed technique eliminates manual parameter selection in Dynalign and provides significant computational time savings in comparison to prior constraints in Dynalign while simultaneously providing a small improvement in the structural prediction accuracy. Savings are also realized in memory. In experiments over a 5S RNA dataset with average sequence length of approximately 120 nucleotides, the method reduces computation by a factor of 2. The method performs favorably in comparison to other programs for pairwise RNA structure prediction: yielding better accuracy, on average, and requiring significantly lesser computational resources. Conclusion Probabilistic analysis can be utilized in order to automate the determination of alignment constraints for pairwise RNA structure prediction methods in a principled fashion. These constraints can reduce the computational and memory requirements of these methods while maintaining or improving their accuracy of structural prediction. This extends the practical reach of these methods to longer length sequences. The revised Dynalign code is freely available for download. PMID:17445273

Evaluating Composite Sampling Methods of Bacillus spores at Low Concentrations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hess, Becky M.; Amidan, Brett G.; Anderson, Kevin K.

Restoring facility operations after the 2001 Amerithrax attacks took over three months to complete, highlighting the need to reduce remediation time. The most time intensive tasks were environmental sampling and sample analyses. Composite sampling allows disparate samples to be combined, with only a single analysis needed, making it a promising method to reduce response times. We developed a statistical experimental design to test three different composite sampling methods: 1) single medium single pass composite: a single cellulose sponge samples multiple coupons; 2) single medium multi-pass composite: a single cellulose sponge is used to sample multiple coupons; and 3) multi-medium post-samplemore » composite: a single cellulose sponge samples a single surface, and then multiple sponges are combined during sample extraction. Five spore concentrations of Bacillus atrophaeus Nakamura spores were tested; concentrations ranged from 5 to 100 CFU/coupon (0.00775 to 0.155CFU/cm2, respectively). Study variables included four clean surface materials (stainless steel, vinyl tile, ceramic tile, and painted wallboard) and three grime coated/dirty materials (stainless steel, vinyl tile, and ceramic tile). Analysis of variance for the clean study showed two significant factors: composite method (p-value < 0.0001) and coupon material (p-value = 0.0008). Recovery efficiency (RE) was higher overall using the post-sample composite (PSC) method compared to single medium composite from both clean and grime coated materials. RE with the PSC method for concentrations tested (10 to 100 CFU/coupon) was similar for ceramic tile, painted wall board, and stainless steel for clean materials. RE was lowest for vinyl tile with both composite methods. Statistical tests for the dirty study showed RE was significantly higher for vinyl and stainless steel materials, but significantly lower for ceramic tile. These results suggest post-sample compositing can be used to reduce sample analysis time when responding to a Bacillus anthracis contamination event of clean or dirty surfaces.« less

Reduction of capacity decay in vanadium flow batteries by an electrolyte-reflow method

NASA Astrophysics Data System (ADS)

Wang, Ke; Liu, Le; Xi, Jingyu; Wu, Zenghua; Qiu, Xinping

2017-01-01

Electrolyte imbalance is a major issue with Vanadium flow batteries (VFBs) as it has a significant impact on electrolyte utilization and cycle life over extended charge-discharge cycling. This work seeks to reduce capacity decay and prolong cycle life of VFBs by adopting a novel electrolyte-reflow method. Different current density and various start-up time of the method are investigated in the charge-discharge tests. The results show that the capacity decay rate is reduced markedly and the cycle life is prolonged substantially by this method. In addition, the coulomb efficiency, voltage efficiency and energy efficiency remain stable during the whole cycle life test, which indicates this method has little impact on the long lifetime performance of the VFBs. The method is low-cost, simple, effective, and can be applied in industrial VFB productions.

CeasIng Cpap At standarD criteriA (CICADA): impact on weight gain, time to full feeds and caffeine use.

PubMed

Broom, Margaret; Ying, Lei; Wright, Audrey; Stewart, Alice; Abdel-Latif, Mohamed E; Shadbolt, Bruce; Todd, David A

2014-09-01

In our previous randomised controlled trial (RCT), we have shown in preterm babies (PBs) <30 weeks gestation that CeasIng Cpap At standarD criteriA (CICADA (method 1)) compared with cycling off continuous positive airway pressure (CPAP) gradually (method 2) or cycling off CPAP gradually with low flow air/oxygen during periods off CPAP (method 3) reduces CPAP cessation time in PBs <30 weeks gestation. This retrospective study reviewed weight gain, time to reach full feeds and time to cease caffeine in PBs previously enrolled in the RCT. Data were collected from 162 of the 177 PBs, and there was no significant difference in the projected weight gain between the three methods. Based on intention to treat, the time taken to reach full feeds for all three methods showed no significant difference. However, post hoc analysis showed the CICADA method compared with cycling off gradually just failed significance (30.3±1.6 vs 31.1±2.4 (weeks corrected gestational age (Wks CGA±SD)), p=0.077). Analysis of time to cease caffeine showed there was a significant difference between the methods with PBs randomised to the CICADA method compared with the cycling off method ceasing caffeine almost a week earlier (33.6±2.4 vs 34.5±2.8 (Wks CGA±SD), p=0.02). This retrospective study provides evidence to substantiate the optimum method of ceasing CPAP; the CICADA method, does not adversely affect weight gain, time to reach full feeds and may reduce time to cease caffeine in PBs <30 weeks gestation. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Robotics and Automation for Flight Deck Aircraft Servicing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chesser, J.B.; Draper, J.V.; Pin, F.G.

1999-03-01

One of the missions of the Future Aircraft Carriers Program is to investigate methods that would improve aircraft turnaround servicing activities on carrier decks. The major objectives and criteria for evaluating alternative aircraft servicing methods are to reduce workload requirements, turnaround times (TAT), and life-cycle costs (LCC). Technologies in the field of Robotics and Automation (R and A) have the potential to significantly contribute to these objectives. The objective of this study was to investigate aircraft servicing functions on carrier decks which would offer the potentially most significant payoff if improved by various R and A technologies. Improvement in thismore » case means reducing workload, time and LCC. This objective was accomplished using a ''bottom-up'' formalized approach as described in the following.« less

Aircraft engine pollution reduction.

NASA Technical Reports Server (NTRS)

Rudey, R. A.

1972-01-01

The effect of engine operation on the types and levels of the major aircraft engine pollutants is described and the major factors governing the formation of these pollutants during the burning of hydrocarbon fuel are discussed. Methods which are being explored to reduce these pollutants are discussed and their application to several experimental research programs are pointed out. Results showing significant reductions in the levels of carbon monoxide, unburned hydrocarbons, and oxides of nitrogen obtained from experimental combustion research programs are presented and discussed to point out potential application to aircraft engines. An experimental program designed to develop and demonstrate these and other advanced, low pollution combustor design methods is described. Results that have been obtained to date indicate considerable promise for reducing advanced engine exhaust pollutants to levels significantly below current engines.

A novel curvilinear approach for prostate seed implantation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Podder, Tarun K.; Dicker, Adam P.; Hutapea, Parsaoran

Purpose: A new technique called ''curvilinear approach'' for prostate seed implantation has been proposed. The purpose of this study is to evaluate the dosimetric benefit of curvilinear distribution of seeds for low-dose-rate (LDR) prostate brachytherapy. Methods: Twenty LDR prostate brachytherapy cases planned intraoperatively with VariSeed planning system and I-125 seeds were randomly selected as reference rectilinear cases. All the cases were replanned by using curved-needle approach keeping the same individual source strength and the volume receiving 100% of prescribed dose 145 Gy (V{sub 100}). Parameters such as number of needles, seeds, and the dose coverage of the prostate (D{sub 90},more » V{sub 150}, V{sub 200}), urethra (D{sub 30}, D{sub 10}) and rectum (D{sub 5}, V{sub 100}) were compared for the rectilinear and the curvilinear methods. Statistical significance was assessed using two-tailed student's t-test. Results: Reduction of the required number of needles and seeds in curvilinear method were 30.5% (p < 0.001) and 11.8% (p < 0.49), respectively. Dose to the urethra was reduced significantly; D{sub 30} reduced by 10.1% (p < 0.01) and D{sub 10} reduced by 9.9% (p < 0.02). Reduction in rectum dose D{sub 5} was 18.5% (p < 0.03) and V{sub 100} was also reduced from 0.93 cc in rectilinear to 0.21 cc in curvilinear (p < 0.001). Also the V{sub 150} and V{sub 200} coverage of prostate reduced by 18.8% (p < 0.01) and 33.9% (p < 0.001), respectively. Conclusions: Significant improvement in the relevant dosimetric parameters was observed in curvilinear needle approach. Prostate dose homogeneity (V{sub 150}, V{sub 200}) improved while urethral dose was reduced, which might potentially result in better treatment outcome. Reduction in rectal dose could potentially reduce rectal toxicity and complications. Reduction in number of needles would minimize edema and thereby could improve postimplant urinary incontinence. This study indicates that the curvilinear implantation approach is dosimetrically superior to conventional rectilinear implantation technique.« less

Antioxidant and hypolipidemic activity of Kumbhajatu in hypercholesterolemic rats

PubMed Central

Ghosh, Rumi; Kadam, Parag P.; Kadam, Vilasrao J.

2010-01-01

Objective: To study the efficacy of Kumbhajatu in reducing the cholesterol levels and as an antioxidant in hypercholesterolemic rats. Materials and Methods: Hypercholesterolemia was induced in normal rats by including 2% w/w cholesterol, 1% w/w sodium cholate and 2.5% w/w coconut oil in the normal diet. Powdered form of Kumbhajatu was administered as feed supplement at 250 and 500 mg/kg dose levels to the hypercholesterolemic rats. Plasma lipid profile, hepatic superoxide dismutase (SOD) activity, catalase activity, reduced glutathione and extent of lipid peroxidation in the form of malondialdehyde were estimated using standard methods. Results: Feed supplementation with 250 and 500 mg/kg of Kumbhajatu resulted in a significant decline in plasma lipid profiles. The feed supplementation increased the concentration of catalase, SOD, glutathione and HDL-c significantly in both the experimental groups (250 and 500 mg/kg). On the other hand, the concentration of malondialdehyde, cholesterol, triglycerides, LDL-c and VLDL in these groups (250 and 500 mg/kg) were decreased significantly. Conclusion: The present study demonstrates that addition of Kumbhajatu powder at 250 and 500 mg/kg level as a feed supplement reduces the plasma lipid levels and also decreases lipid peroxidation. PMID:21170207

Antioxidant, analgesic and anti-inflammatory activities of the methanolic extract of Piper betle leaves

PubMed Central

Alam, Badrul; Akter, Fahima; Parvin, Nahida; Sharmin Pia, Rashna; Akter, Sharmin; Chowdhury, Jesmin; Sifath-E-Jahan, Kazi; Haque, Ekramul

2013-01-01

Objective: The present study was designed to evaluate the antioxidant, analgesic, and anti-inflammatory activities of the methanolic extract of Piper betle leaves (MPBL). Materials and Methods: MPBL was evaluated for anti-inflammatory activity using carrageenan-induced hind paw edema model. Analgesic activity of MPBL was evaluated by hot plate, writhing, and formalin tests. Total phenolic and flavonoids content, total antioxidant activity, scavenging of 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical, peroxynitrate (ONOO) as well as inhibition of total ROS generation, and assessment of reducing power were used to evaluate antioxidant potential of MPBL. Results: The extract of MPBL, at the dose of 100 and 200 mg/kg, produced a significant (p<0.05) increase in pain threshold in hot plate method whereas significantly (p<0.05) reduced the writhing caused by acetic acid and the number of licks induced by formalin in a dose-dependent manner. The same ranges of doses of MPBL caused significant (p<0.05) inhibition of carrageenan-induced paw edema after 4 h in a dose-dependent manner. In DPPH, ONOO-, and total ROS scavenging method, MPBL showed good antioxidant potentiality with the IC50 value of 16.33±1.02, 25.16±0.61 , and 41.72±0.48 µg/ml, respectively with a significant (p<0.05) good reducing power. Conclusion: The findings of the study suggested that MPBL has strong analgesic, anti-inflammatory, and antioxidant effects, conforming the traditional use of this plant for inflammatory pain alleviation to its antioxidant potentiality. PMID:25050265

The effectiveness of an educational intervention to improve knowledge and perceptions for reducing organophosphate pesticide exposure among Indonesian and South Australian migrant farmworkers

PubMed Central

Suratman, Suratman; Ross, Kirstin E; Babina, Kateryna; Edwards, John William

2016-01-01

Background Farmworkers are at risk of exposure to organophosphate pesticides (OPs). Improvements of knowledge and perceptions about organophosphate (OP) exposure may be of benefit for the reduction in OP exposure. Purpose The purpose of this study was to examine the effectiveness of an educational intervention to improve knowledge and perceptions for reducing OP exposure among Indonesian and South Australian (SA) migrant farmworkers. Methods This was a quasi-experimental study. The educational intervention used a method of group communication for 30 Indonesian farmworkers and individual communication for seven SA migrant farmworkers. Knowledge and perceptions about OP exposure were measured pre-intervention and 3 months after the intervention. Results Unadjusted intervention effects at follow-up showed statistically significantly improved scores of knowledge (both adverse effects of OPs and self-protection from OP exposure), perceived susceptibility, and perceived barriers among Indonesian farmworkers compared with SA migrant farmworkers. Furthermore, these four significant variables in the unadjusted model and the two other variables (perceived severity and perceived benefits) were statistically significant after being adjusted for the level of education and years working as a farmworker. In contrast, knowledge about adverse effects of OPs was the only variable that was statistically significantly improved among SA migrant farmworkers. The results of this study suggests educational interventions using a method of group communication could be more effective than using individual intervention. Conclusion These improvements provide starting points to change health behavior of farmworkers, particularly to reduce OP exposure, both at the workplace and at home. PMID:26855602

Effect of kinesiotaping, non-elastic taping and bracing on segmental foot kinematics during drop landing in healthy subjects and subjects with chronic ankle instability.

PubMed

Kuni, B; Mussler, J; Kalkum, E; Schmitt, H; Wolf, S I

2016-09-01

To evaluate the effects of kinesiotape, non-elastic tape, and soft brace on segmental foot kinematics during drop landing in subjects with chronic ankle instability and healthy subjects. Controlled study with repeated measurements. Three-dimensional motion analysis laboratory. Twenty participants with chronic ankle instability and 20 healthy subjects. The subjects performed drop landings with 17 retroreflective markers on the foot and lower leg in four conditions: barefoot, with kinesiotape, with non-elastic tape and with a soft brace. Ranges of motion of foot segments using a foot measurement method. In participants with chronic ankle instability, midfoot movement in the frontal plane (inclination of the medial arch) was reduced significantly by non-elastic taping, but kinesiotaping and bracing had no effect. In healthy subjects, both non-elastic taping and bracing reduced that movement. In both groups, non-elastic taping and bracing reduced rearfoot excursion in inversion/eversion significantly, which indicates a stabilisation effect. No such effect was found with kinesiotaping. All three methods reduced maximum plantar flexion significantly. Non-elastic taping stabilised the midfoot best in patients with chronic ankle instability, while kinesiotaping did not influence foot kinematics other than to stabilise the rearfoot in the sagittal plane. ClinicalTrials.gov NCT01810471. Copyright © 2015 Chartered Society of Physiotherapy. Published by Elsevier Ltd. All rights reserved.

Fault Diagnosis for Rotating Machinery: A Method based on Image Processing

PubMed Central

Lu, Chen; Wang, Yang; Ragulskis, Minvydas; Cheng, Yujie

2016-01-01

Rotating machinery is one of the most typical types of mechanical equipment and plays a significant role in industrial applications. Condition monitoring and fault diagnosis of rotating machinery has gained wide attention for its significance in preventing catastrophic accident and guaranteeing sufficient maintenance. With the development of science and technology, fault diagnosis methods based on multi-disciplines are becoming the focus in the field of fault diagnosis of rotating machinery. This paper presents a multi-discipline method based on image-processing for fault diagnosis of rotating machinery. Different from traditional analysis method in one-dimensional space, this study employs computing method in the field of image processing to realize automatic feature extraction and fault diagnosis in a two-dimensional space. The proposed method mainly includes the following steps. First, the vibration signal is transformed into a bi-spectrum contour map utilizing bi-spectrum technology, which provides a basis for the following image-based feature extraction. Then, an emerging approach in the field of image processing for feature extraction, speeded-up robust features, is employed to automatically exact fault features from the transformed bi-spectrum contour map and finally form a high-dimensional feature vector. To reduce the dimensionality of the feature vector, thus highlighting main fault features and reducing subsequent computing resources, t-Distributed Stochastic Neighbor Embedding is adopt to reduce the dimensionality of the feature vector. At last, probabilistic neural network is introduced for fault identification. Two typical rotating machinery, axial piston hydraulic pump and self-priming centrifugal pumps, are selected to demonstrate the effectiveness of the proposed method. Results show that the proposed method based on image-processing achieves a high accuracy, thus providing a highly effective means to fault diagnosis for rotating machinery. PMID:27711246

Does counselling improve uptake of long-term and permanent contraceptive methods in a high HIV-prevalence setting?

PubMed

Siveregi, Amon; Dudley, Lilian; Makumucha, Courage; Dlamini, Phatisizwe; Moyo, Sihle; Bhembe, Sibongiseni

2015-11-06

Studies have shown a reduced uptake of contraceptive methods in HIV-positive women of childbearing age, mainly because of unmet needs that may be a result of poor promotion of available methods of contraception, especially long-term and permanent methods (LTPM). To compare the uptake of contraceptive methods, and particularly LTPM, by HIV-positive and HIV negative post-partum mothers, and to assess the effects of counselling on contraceptive choices. Three government district hospitals in Swaziland. Interviews were conducted using a structured questionnaire, before and after counselling HIV negativeand HIV-positive post-partum women in LTPM use, unintended pregnancy rates, future fertility and reasons for contraceptive choices. A total of 711 women, of whom half were HIV-positive, participated in the study. Most (72.3% HIV-negative and 84% HIV-positive) were on modern methods of contraception, with the majority using 2-monthly and 3-monthly injectables. Intended use of any contraceptive increased to 99% after counselling. LTPM use was 7.0% in HIV-negative mothers and 15.3% in HIV-positive mothers before counselling, compared with 41.3% and 42.4% in HIV-negative and HIV-positive mothers, respectively, after counselling. Pregnancy intentions and counselling on future fertility were significantly associated with current use of contraception, whilst current LTPM use and level of education were significantly associated with LTPM post-counselling. Counselling on all methods including LTPM reduced unmet needs in contraception in HIV positive and HIV-negative mothers and could improve contraceptive uptake and reduce unintended pregnancies. Health workers do not always remember to include LTPM when they counsel clients, which could result in a low uptake of these methods. Further experimental studies should be conducted to validate these results.

Fault Diagnosis for Rotating Machinery: A Method based on Image Processing.

PubMed

Lu, Chen; Wang, Yang; Ragulskis, Minvydas; Cheng, Yujie

2016-01-01

Rotating machinery is one of the most typical types of mechanical equipment and plays a significant role in industrial applications. Condition monitoring and fault diagnosis of rotating machinery has gained wide attention for its significance in preventing catastrophic accident and guaranteeing sufficient maintenance. With the development of science and technology, fault diagnosis methods based on multi-disciplines are becoming the focus in the field of fault diagnosis of rotating machinery. This paper presents a multi-discipline method based on image-processing for fault diagnosis of rotating machinery. Different from traditional analysis method in one-dimensional space, this study employs computing method in the field of image processing to realize automatic feature extraction and fault diagnosis in a two-dimensional space. The proposed method mainly includes the following steps. First, the vibration signal is transformed into a bi-spectrum contour map utilizing bi-spectrum technology, which provides a basis for the following image-based feature extraction. Then, an emerging approach in the field of image processing for feature extraction, speeded-up robust features, is employed to automatically exact fault features from the transformed bi-spectrum contour map and finally form a high-dimensional feature vector. To reduce the dimensionality of the feature vector, thus highlighting main fault features and reducing subsequent computing resources, t-Distributed Stochastic Neighbor Embedding is adopt to reduce the dimensionality of the feature vector. At last, probabilistic neural network is introduced for fault identification. Two typical rotating machinery, axial piston hydraulic pump and self-priming centrifugal pumps, are selected to demonstrate the effectiveness of the proposed method. Results show that the proposed method based on image-processing achieves a high accuracy, thus providing a highly effective means to fault diagnosis for rotating machinery.

Multi-element least square HDMR methods and their applications for stochastic multiscale model reduction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Lijian, E-mail: ljjiang@hnu.edu.cn; Li, Xinping, E-mail: exping@126.com

Stochastic multiscale modeling has become a necessary approach to quantify uncertainty and characterize multiscale phenomena for many practical problems such as flows in stochastic porous media. The numerical treatment of the stochastic multiscale models can be very challengeable as the existence of complex uncertainty and multiple physical scales in the models. To efficiently take care of the difficulty, we construct a computational reduced model. To this end, we propose a multi-element least square high-dimensional model representation (HDMR) method, through which the random domain is adaptively decomposed into a few subdomains, and a local least square HDMR is constructed in eachmore » subdomain. These local HDMRs are represented by a finite number of orthogonal basis functions defined in low-dimensional random spaces. The coefficients in the local HDMRs are determined using least square methods. We paste all the local HDMR approximations together to form a global HDMR approximation. To further reduce computational cost, we present a multi-element reduced least-square HDMR, which improves both efficiency and approximation accuracy in certain conditions. To effectively treat heterogeneity properties and multiscale features in the models, we integrate multiscale finite element methods with multi-element least-square HDMR for stochastic multiscale model reduction. This approach significantly reduces the original model's complexity in both the resolution of the physical space and the high-dimensional stochastic space. We analyze the proposed approach, and provide a set of numerical experiments to demonstrate the performance of the presented model reduction techniques. - Highlights: • Multi-element least square HDMR is proposed to treat stochastic models. • Random domain is adaptively decomposed into some subdomains to obtain adaptive multi-element HDMR. • Least-square reduced HDMR is proposed to enhance computation efficiency and approximation accuracy in certain conditions. • Integrating MsFEM and multi-element least square HDMR can significantly reduce computation complexity.« less

Method for rapidly producing microporous and mesoporous materials

DOEpatents

Coronado, Paul R.; Poco, John F.; Hrubesh, Lawrence W.; Hopper, Robert W.

1997-01-01

An improved, rapid process is provided for making microporous and mesoporous materials, including aerogels and pre-ceramics. A gel or gel precursor is confined in a sealed vessel to prevent structural expansion of the gel during the heating process. This confinement allows the gelation and drying processes to be greatly accelerated, and significantly reduces the time required to produce a dried aerogel compared to conventional methods. Drying may be performed either by subcritical drying with a pressurized fluid to expel the liquid from the gel pores or by supercritical drying. The rates of heating and decompression are significantly higher than for conventional methods.

A walkthrough solution to the boundary overlap problem

Treesearch

Mark J. Ducey; Jeffrey H. Gove; Harry T. Valentine

2004-01-01

Existing methods for eliminating bias due to boundary overlap suffer some disadvantages in practical use, including the need to work outside the tract, restrictions on the kinds of boundaries to which they are applicable, and the possibility of significantly increased variance as a price for unbiasedness. We propose a new walkthrough method for reducing boundary...

Method for shaping polyethylene tubing

NASA Technical Reports Server (NTRS)

Kramer, R. C.

1981-01-01

Method forms polyethylene plastic tubing into configurations previously only possible with metal tubing. By using polyethylene in place of copper or stain less steel tubing inlow pressure systems, fabrication costs are significantly reduced. Polyethylene tubing can be used whenever low pressure tubing is needed in oil operations, aircraft and space applications, powerplants, and testing laboratories.

Nox Emission Reduction in Commercial Jets Through Water Injection

NASA Technical Reports Server (NTRS)

Balepin, Vladimir; Ossello, Chris; Snyder, Chris

2002-01-01

This paper discusses a method of the nitrogen oxides (NOx) emission reduction through the injection of water in commercial turbofan engines during the takeoff and climbout cycles. In addition to emission reduction, this method can significantly reduce turbine temperature during the most demanding operational modes (takeoff and climbout) and increase engine reliability and life.

Streamed video clips to reduce anxiety in children during inhaled induction of anesthesia.

PubMed

Mifflin, Katherine A; Hackmann, Thomas; Chorney, Jill Maclaren

2012-11-01

Anesthesia induction in children is frequently achieved by inhalation of nitrous oxide and sevoflurane. Pediatric anesthesiologists commonly use distraction techniques such as humor or nonprocedural talk to reduce anxiety and facilitate a smooth transition at this critical phase. There is a large body of successful distraction research that explores the use of video and television distraction methods for minor medical and dental procedures, but little research on the use of this method for ambulatory surgery. In this randomized control trial study we examined whether video distraction is effective in reducing the anxiety of children undergoing inhaled induction before ambulatory surgery. Children (control = 47, video = 42) between 2 and 10 years old undergoing ambulatory surgery were randomly assigned to a video distraction or control group. In the video distraction group a video clip of the child's preference was played during induction, and the control group received traditional distraction methods during induction. The modified Yale Preoperative Anxiety Scale was used to assess the children's anxiety before and during the process of receiving inhalation anesthetics. All subjects were similar in their age and anxiety scores before entering the operating rooms. Children in the video distraction group were significantly less anxious at induction and showed a significantly smaller change in anxiety from holding to induction than did children in the control group. Playing video clips during the inhaled induction of children undergoing ambulatory surgery is an effective method of reducing anxiety. Therefore, pediatric anesthesiologists may consider using video distraction as a useful, valid, alternative strategy for achieving a smooth transition to the anesthetized state.

Effect of Cord Blood Processing on Transplant Outcomes after Single Myeloablative Umbilical Cord Blood Transplantation

PubMed Central

Ballen, Karen K.; Logan, Brent R.; Laughlin, Mary J.; He, Wensheng; Ambruso, Daniel R.; Armitage, Susan E.; Beddard, Rachel L.; Bhatla, Deepika; Hwang, William Y.K.; Kiss, Joseph E.; Koegler, Gesine; Kurtzberg, Joanne; Nagler, Arnon; Oh, David; Petz, Lawrence D.; Price, Thomas H.; Quinones, Ralph R.; Ratanatharathorn, Voravit; Rizzo, J. Douglas; Sazama, Kathleen; Scaradavou, Andromachi; Schuster, Michael W.; Sender, Leonard S.; Shpall, Elizabeth J.; Spellman, Stephen R.; Sutton, Millicent; Weitekamp, Lee Ann; Wingard, John R.; Eapen, Mary

2015-01-01

Variations in cord blood manufacturing and administration are common, and the optimal practice, not known. We compared processing and banking practices at 16 public cord blood banks (CBB) in the United States, and assessed transplant outcomes on 530 single umbilical cord blood (UCB) myeloablative transplantations for hematologic malignancies, facilitated by these banks. UCB banking practices were separated into three mutually exclusive groups based on whether processing was automated or manual; units were plasma and red blood cell reduced or buffy coat production method or plasma reduced. Compared to the automated processing system for units, the day-28 neutrophil recovery was significantly lower after transplantation of units that were manually processed and plasma reduced (red cell replete) (odds ratio [OR] 0.19 p=0.001) or plasma and red cell reduced (OR 0.54, p=0.05). Day-100 survival did not differ by CBB. However, day-100 survival was better with units that were thawed with the dextran-albumin wash method compared to the “no wash” or “dilution only” techniques (OR 1.82, p=0.04). In conclusion, CBB processing has no significant effect on early (day 100) survival despite differences in kinetics of neutrophil recovery. PMID:25543094

Association of β-defensin copy number and psoriasis in three cohorts of European origin

PubMed Central

Stuart, Philip E; Hüffmeier, Ulrike; Nair, Rajan P; Palla, Raquel; Tejasvi, Trilokraj; Schalkwijk, Joost; Elder, James T; Reis, Andre; Armour, John AL

2012-01-01

A single previous study has demonstrated significant association of psoriasis with copy number of beta-defensin genes, using DNA from psoriasis cases and controls from Nijmegen and Erlangen. In this study we attempted to replicate that finding in larger new cohorts from Erlangen (N = 2017) and Michigan (N = 5412), using improved methods for beta-defensin copy number determination based on the paralog ratio test (PRT), and enhanced methods of analysis and association testing implemented in the CNVtools resource. We demonstrate that the association with psoriasis found in the discovery sample is maintained after applying improved typing and analysis methods (p = 5.5 × 10−4, OR = 1.25). We also find that the association is replicated in 2616 cases and 2526 controls from Michigan, although at reduced significance (p = 0.014), but not in new samples from Erlangen (1396 cases and 621 controls, p = 0.38). Meta-analysis across all cohorts suggests a nominally significant association (p = 6.6 × 10−3/2 × 10−4) with an effect size (OR = 1.081) much lower than found in the discovery study (OR = 1.32). This reduced effect size and significance on replication is consistent with a genuine but weak association. PMID:22739795

Surface-Based fMRI-Driven Diffusion Tractography in the Presence of Significant Brain Pathology: A Study Linking Structure and Function in Cerebral Palsy

PubMed Central

Cunnington, Ross; Boyd, Roslyn N.; Rose, Stephen E.

2016-01-01

Diffusion MRI (dMRI) tractography analyses are difficult to perform in the presence of brain pathology. Automated methods that rely on cortical parcellation for structural connectivity studies often fail, while manually defining regions is extremely time consuming and can introduce human error. Both methods also make assumptions about structure-function relationships that may not hold after cortical reorganisation. Seeding tractography with functional-MRI (fMRI) activation is an emerging method that reduces these confounds, but inherent smoothing of fMRI signal may result in the inclusion of irrelevant pathways. This paper describes a novel fMRI-seeded dMRI-analysis pipeline based on surface-meshes that reduces these issues and utilises machine-learning to generate task specific white matter pathways, minimising the requirement for manually-drawn ROIs. We directly compared this new strategy to a standard voxelwise fMRI-dMRI approach, by investigating correlations between clinical scores and dMRI metrics of thalamocortical and corticomotor tracts in 31 children with unilateral cerebral palsy. The surface-based approach successfully processed more participants (87%) than the voxel-based approach (65%), and provided significantly more-coherent tractography. Significant correlations between dMRI metrics and five clinical scores of function were found for the more superior regions of these tracts. These significant correlations were stronger and more frequently found with the surface-based method (15/20 investigated were significant; R2 = 0.43–0.73) than the voxelwise analysis (2 sig. correlations; 0.38 & 0.49). More restricted fMRI signal, better-constrained tractography, and the novel track-classification method all appeared to contribute toward these differences. PMID:27487011

Modeling and simulation of ocean wave propagation using lattice Boltzmann method

NASA Astrophysics Data System (ADS)

Nuraiman, Dian

2017-10-01

In this paper, we present on modeling and simulation of ocean wave propagation from the deep sea to the shoreline. This requires high computational cost for simulation with large domain. We propose to couple a 1D shallow water equations (SWE) model with a 2D incompressible Navier-Stokes equations (NSE) model in order to reduce the computational cost. The coupled model is solved using the lattice Boltzmann method (LBM) with the lattice Bhatnagar-Gross-Krook (BGK) scheme. Additionally, a special method is implemented to treat the complex behavior of free surface close to the shoreline. The result shows the coupled model can reduce computational cost significantly compared to the full NSE model.

Reference tissue modeling with parameter coupling: application to a study of SERT binding in HIV

NASA Astrophysics Data System (ADS)

Endres, Christopher J.; Hammoud, Dima A.; Pomper, Martin G.

2011-04-01

When applicable, it is generally preferred to evaluate positron emission tomography (PET) studies using a reference tissue-based approach as that avoids the need for invasive arterial blood sampling. However, most reference tissue methods have been shown to have a bias that is dependent on the level of tracer binding, and the variability of parameter estimates may be substantially affected by noise level. In a study of serotonin transporter (SERT) binding in HIV dementia, it was determined that applying parameter coupling to the simplified reference tissue model (SRTM) reduced the variability of parameter estimates and yielded the strongest between-group significant differences in SERT binding. The use of parameter coupling makes the application of SRTM more consistent with conventional blood input models and reduces the total number of fitted parameters, thus should yield more robust parameter estimates. Here, we provide a detailed evaluation of the application of parameter constraint and parameter coupling to [11C]DASB PET studies. Five quantitative methods, including three methods that constrain the reference tissue clearance (kr2) to a common value across regions were applied to the clinical and simulated data to compare measurement of the tracer binding potential (BPND). Compared with standard SRTM, either coupling of kr2 across regions or constraining kr2 to a first-pass estimate improved the sensitivity of SRTM to measuring a significant difference in BPND between patients and controls. Parameter coupling was particularly effective in reducing the variance of parameter estimates, which was less than 50% of the variance obtained with standard SRTM. A linear approach was also improved when constraining kr2 to a first-pass estimate, although the SRTM-based methods yielded stronger significant differences when applied to the clinical study. This work shows that parameter coupling reduces the variance of parameter estimates and may better discriminate between-group differences in specific binding.

Comparison of Cryopreserved Human Sperm between Ultra Rapid Freezing and Slow Programmable Freezing: Effect on Motility, Morphology and DNA Integrity.

PubMed

Tongdee, Pattama; Sukprasert, Matchuporn; Satirapod, Chonticha; Wongkularb, Anna; Choktanasiri, Wicham

2015-05-01

Cryopreservation of sperm is common methods to preserve male fertility. Sperm freezing, suggest slow programmable freezing caused lower change of sperm morphology than sperm freezing in vapor of liquid nitrogen. Ultra rapid freezing is easy to be worked on, less time, low cost and does not need high experience. To compare the effect on sperm motility, morphology and DNA integrity of post-thawed sperm after ultra rapid freezing and slow programmable freezing methods. Experimental study at laboratory of infertility unit, Department of Obstetrics and Gynecology, Faculty of Medicine Ramathibodi Hospital. Thirty-seven semen samples with normal semen analysis according to World Health Organization (WHO) 1999 [normal sperm volume ( 2 ml) and normal sperm concentration (≥ 20 x10(6)/ml) and sperm motility (≥ 50%)]. Semen samples were washed. Then each semen sample was divided into six cryovials. Two cryovials, 0.5 ml each, were cryopreserved by slow programmable freezing. Four 0.25 ml containing cryovials, were cryopreserved by ultra rapidfreezing method. After cryopreservationfor 1 month, thawedprocess was carried out at room temperature. Main outcomes are sperm motility was determined by Computer-Assisted Semen Analysis (CASA), sperm morphology was determined by eosin-methylene blue staining and sperm DNA integrity was assessed by TUNEL assay. Sperm motility was reduced significantly by both methods, from 70.4 (9.0)% to 29.1 (12.3)% in slowprogrammable freezing and to 19.7 (9.8)% in ultra rapid freezing (p < 0.05). Sperm motility decreased significantly more by ultra rapid freezing (p < 0.001). The percentage of normal sperm morphology and DNA integrity were also reduced significantly by both methods. However, no significant difference between the two methods was found (p > 0.05). Cryopreservation of human sperm for 1 month significantly decreased sperm motility, morphology and DNA integrity in both methods. However sperm motility was decreased more by ultra rapid freezing.

An evaluation of technologies for the heavy metal remediation of dredged sediments.

PubMed

Mulligan, C N; Yong, R N; Gibbs, B F

2001-07-30

Sediments dewatering is frequently necessary after dredging to remediate and treat contaminants. Methods include draining of the water in lagoons with or without coagulants and flocculants, or using presses or centrifuges. Treatment methods are similar to those used for soil and include pretreatment, physical separation, thermal processes, biological decontamination, stabilization/solidification and washing. However, compared to soil treatment, few remediation techniques have been commercially used for sediments. In this paper, a review of the methods that have been used and an evaluation of developed and developing technologies is made. Sequential extraction technique can be a useful tool for determining metal speciation before and after washing. Solidification/stabilization techniques are successful but significant monitoring is required, since the solidification process can be reversible. In addition, the presence of organics can reduce treatment efficiency. Vitrification is applicable for sediments but expensive. Only if a useful glass product can be sold will this process be economically viable. Thermal processes are only applicable for removal of volatile metals, such as mercury and costs are high. Biological processes are under development and have the potential to be low cost. Since few low cost metal treatment processes for sediments are available, there exists significant demand for further development. Pretreatment may be one of the methods that can reduce costs by reducing the volumes of sediments that need to be treated.

A prospective randomised study comparing the jubilee dressing method to a standard adhesive dressing for total hip and knee replacements.

PubMed

Burke, Neil G; Green, Connor; McHugh, Gavin; McGolderick, Niall; Kilcoyne, Carol; Kenny, Patrick

2012-08-01

It is important to reduce potential wound complications in total hip and total knee arthroplasty procedures. The purpose of this study was to compare the jubilee dressing method to a standard adhesive dressing. 124 patients (62 total hip replacements and 62 total knee replacements) were randomly selected to have either a standard adhesive dressing or jubilee method dressing. The number of dressing changes, incidence of blistering, leakage, appearance of inflammation, infection rate and the average stay in hospital was recorded for each patient. The jubilee dressing significantly reduced the rate of blistering, leakage and number of dressing changes when compare to a traditional adhesive dressing (p < 0.05). The rate of inflammation and average length of stay in hospital was not significantly different between the two groups. The authors recommend the use of this dressing for total hip and total knee arthroplasty procedures due to the associated lower complication rate. Copyright © 2012 Tissue Viability Society. Published by Elsevier Ltd. All rights reserved.

Fast H.264/AVC FRExt intra coding using belief propagation.

PubMed

Milani, Simone

2011-01-01

In the H.264/AVC FRExt coder, the coding performance of Intra coding significantly overcomes the previous still image coding standards, like JPEG2000, thanks to a massive use of spatial prediction. Unfortunately, the adoption of an extensive set of predictors induces a significant increase of the computational complexity required by the rate-distortion optimization routine. The paper presents a complexity reduction strategy that aims at reducing the computational load of the Intra coding with a small loss in the compression performance. The proposed algorithm relies on selecting a reduced set of prediction modes according to their probabilities, which are estimated adopting a belief-propagation procedure. Experimental results show that the proposed method permits saving up to 60 % of the coding time required by an exhaustive rate-distortion optimization method with a negligible loss in performance. Moreover, it permits an accurate control of the computational complexity unlike other methods where the computational complexity depends upon the coded sequence.

[Effects of sanguisorba tannins and saponins compatibility on pharmacokinetic parameters of catechin, epicatechin and ziyuglycoside Ⅰ in rats].

PubMed

Xiong, Yong-Ai; Yang, Ming

2016-10-01

To study the effects of sanguisorba tannins and saponins compatibility at different proportions [tannins-saponins (1∶1) and tannins-saponins(8∶1)] after intragastric administration (50 mg•kg⁻¹) on pharmacokinetic parameters of catechin, epicatechin and ziyuglycoside Ⅰ in rats by using pharmacokinetic techniques and methods. Kinetica 5.0 software was used to calculate the pharmacokinetic parameters. The results showed that the specificity, linearity, recovery rate, precision and stability of the established detection method were in line with the test requirements. When the sanguisorba tannins and eaponins were combined at the rate of 1∶1, Vd and CL of catechin and epicatechin were increased significantly（P<0.05); MRT was significantly shortened(P<0.05); Cmax and AUC were significantly reduced(P<0.05). When the sanguisorba tannins and saponins were combined at the rate of 8∶1, Vd and CL of catechin and epicatechin were significantly reduced(P<0.05); MRT was significantly prolonged(P<0.05); Cmax and AUC were increased significantly(P<0.05). In addition, with the increase in proportion of sanguisorba tannins in the compatibility, Cmax and AUC of ziyuglycoside Ⅰ were increased significantly(P<0.05); Vd and CL were significantly reduced(P<0.05), Tmax was obviously lagging behind, and MRT was also significantly prolonged(P<0.05). In our present study, catechin, epicatechin and ziyuglycoside Ⅰ showed good pharmacokinetic behavior in rats when sanguisorba tannins and saponins were combined at the rate of 8∶1 in compatibility, which could be used as a reference for the proportion in sanguisorba tannins and saponins compatibility. Copyright© by the Chinese Pharmaceutical Association.

A New Low Complexity Angle of Arrival Algorithm for 1D and 2D Direction Estimation in MIMO Smart Antenna Systems

PubMed Central

Al-Sadoon, Mohammed A. G.; Zuid, Abdulkareim; Jones, Stephen M. R.; Noras, James M.

2017-01-01

This paper proposes a new low complexity angle of arrival (AOA) method for signal direction estimation in multi-element smart wireless communication systems. The new method estimates the AOAs of the received signals directly from the received signals with significantly reduced complexity since it does not need to construct the correlation matrix, invert the matrix or apply eigen-decomposition, which are computationally expensive. A mathematical model of the proposed method is illustrated and then verified using extensive computer simulations. Both linear and circular sensors arrays are studied using various numerical examples. The method is systematically compared with other common and recently introduced AOA methods over a wide range of scenarios. The simulated results show that the new method has several advantages in terms of reduced complexity and improved accuracy under the assumptions of correlated signals and limited numbers of snapshots. PMID:29140313

A New Low Complexity Angle of Arrival Algorithm for 1D and 2D Direction Estimation in MIMO Smart Antenna Systems.

PubMed

Al-Sadoon, Mohammed A G; Ali, Nazar T; Dama, Yousf; Zuid, Abdulkareim; Jones, Stephen M R; Abd-Alhameed, Raed A; Noras, James M

2017-11-15

This paper proposes a new low complexity angle of arrival (AOA) method for signal direction estimation in multi-element smart wireless communication systems. The new method estimates the AOAs of the received signals directly from the received signals with significantly reduced complexity since it does not need to construct the correlation matrix, invert the matrix or apply eigen-decomposition, which are computationally expensive. A mathematical model of the proposed method is illustrated and then verified using extensive computer simulations. Both linear and circular sensors arrays are studied using various numerical examples. The method is systematically compared with other common and recently introduced AOA methods over a wide range of scenarios. The simulated results show that the new method has several advantages in terms of reduced complexity and improved accuracy under the assumptions of correlated signals and limited numbers of snapshots.

Effectiveness of Mindfulness-Based Cognitive Therapy (MBCT) in Reducing Aggression of Individuals at the Juvenile Correction and Rehabilitation Center.

PubMed

Milani, Atefeh; Nikmanesh, Zahra; Farnam, Ali

2013-12-01

In the present era, delinquency in children and adolescents is undoubtedly a difficult and upsetting issue attracting the attention of many experts such as psychologists, sociologists, and criminologists. These experts often try to answer why a number of children and adolescents engage in various crimes such as aggressive and anti-social crimes. They also try to find out how these crimes can be prevented. The present study investigates the effectiveness of mindfulness-based cognitive therapy training (MBCT) in reducing aggression in a juvenile correction and rehabilitation center of Zahedan province during years 1991 to 1992. This experimental study included an experimental and a control group with a pretest, posttest, and follow-up approach. The Buss and Perry aggression questionnaire (1992) was used for data collection. The sample group included 22 (10 experimental and 12 control groups) adolescent males in a juvenile correction and rehabilitation center of Zahedan province who were selected through a census method. Using a matching method based on the pre-test scores of the aggression questionnaire, they were then divided into two equivalent categories and were randomly assigned to the two groups. Mindfulness-based cognitive training took the group training in 8 sessions administered on experimental group. The follow-up test was conducted two weeks after the end of the posttest sessions. The results were analyzed using ANCOVA. The results of ANCOVA showed that mindfulness-based cognitive training could significantly reduce aggression during posttest and follow-up test phases in the experimental group, compared to the control group (P < 0.01). Moreover, the results indicated the effectiveness of this method in significantly reducing anger, physical aggression, and hostility during posttest and follow-up test phases (P < 0.05). However, no significant reduction was observed in the verbal aggression subscale. According to the results of the present study, mindfulness-based cognitive training seems to be effective for reducing aggressive behaviors.

The Effectiveness of Art Therapy in Reducing Internalizing and Externalizing Problems of Female Adolescents.

PubMed

Bazargan, Yasaman; Pakdaman, Shahla

2016-01-01

The internalizing and externalizing problems relating to childhood and adolescent have always been significant. Because there is special considerations in establishing communication with them and hence, the therapeutic methods for these problems must take into account these considerations. As establishing a therapeutic relationship is an important component of effective counseling, it seems that art therapy may help alleviate these problems. The purpose of this study is to determine the effectiveness of art therapy in reducing internalizing and externalizing problems of adolescent girls (14 - 18 years old). This is a semi-experimental study carried out in the form of a pre-test/post-test design with control group. The population of this study includes female students of Gole Laleh School of Art in district 3 of Tehran, Iran, out of which 30 students with internalizing problems and 30 individuals with externalizing problems were selected through targeted sampling. Students were randomly assigned to control and experimental groups. Experimental groups participated in 6 painting sessions designed based on Art therapy theories and previous studies. The material used for diagnosis of the problems in posttest and pretest was an Achenbach self-assessment form. Data were analyzed using a mixed analysis of variance (ANOVA). Our results showed that Art therapy significantly reduced internalizing problems (F = 17.61, P < 0.001); however, its effect in reducing externalizing problems was not significant (F = 3.93, P = 0.06). Art therapy as a practical therapeutic method can be used to improve internalizing problems. To reduce externalizing problems, more sessions may be needed. Thus, future studies are required to insure these findings.

Effect of steepest-meridian clear corneal incision for reducing preexisting corneal astigmatism using a meridian-marking method or surgeon's intuition.

PubMed

Hayashi, Ken; Yoshida, Motoaki; Yoshimura, Koichi

2014-12-01

To compare the effect of steepest-meridian clear corneal incisions (CCIs) for reducing preexisting corneal astigmatism between a meridian-marking method and a surgeon's-intuition method. Hayashi Eye Hospital, Fukuoka, Japan. Randomized controlled trials. Eyes scheduled for phacoemulsification were randomized to 1 of 2 groups: a 2.65 mm steepest-meridian CCI using the meridian-marking method or a 2.65 mm steepest-meridian CCI using the surgeon's intuition. Regular and irregular corneal astigmatism, surgically induced astigmatism (SIA) vector, refractive status, higher-order aberrations (HOAs), uncorrected (UDVA) and corrected (CDVA) distance visual acuities, and physical meridian misalignment of the steepest-meridian CCI measured using anterior segment optical coherence tomography were evaluated preoperatively and 1 month and 3 months postoperatively. The mean meridian misalignment of the steepest-meridian CCIs was significantly smaller in the meridian-marking group (4.4 degrees ± 2.8 [SD]) than in the surgeon's-intuition group (8.6 ± 4.4 degrees) (P ≤.0001). Regular and irregular corneal astigmatism and corneal HOAs did not change significantly postoperatively in either group. No significant difference was found in regular or irregular corneal astigmatism, refractive cylinder, manifest spherical equivalent value, SIA, HOAs, UDVA, or CDVA between the meridian-marking group and the surgeon's-intuition group throughout the follow-up. The physical meridian misalignment of steepest-meridian CCI was significantly smaller with the meridian-marking method than with the surgeon's-intuition method; however, the effect of the difference was not large enough to decrease remaining astigmatism and HOAs or to improve the UDVA. Copyright © 2014 ASCRS and ESCRS. Published by Elsevier Inc. All rights reserved.

A guide for roadside vegetation management

DOT National Transportation Integrated Search

2009-10-01

Implementing a comprehensive turf management program significantly reduces the overall cost of managing the vegetation along state roadways. This guide provides methods for efficiently and effectively managing the activities that will achieve and mai...

Preshaping command inputs to reduce telerobotic system oscillations

NASA Technical Reports Server (NTRS)

Singer, Neil C.; Seering, Warren P.

1989-01-01

The results of using a new technique for shaping inputs to a model of the space shuttle Remote Manipulator System (RMS) are presented. The shapes inputs move the system to the same location that was originally commanded, however, the oscillations of the machine are considerably reduced. An overview of the new shaping method is presented. A description of RMS model is provided. The problem of slow joint servo rates on the RMS is accommodated with an extension of the shaping method. The results and sample data are also presented for both joint and three-dimensional cartesian motions. The results demonstrate that the new shaping method performs well on large, telerobotic systems which exhibit significant structural vibration. The new method is shown to also result in considerable energy savings during operations of the RMS manipulator.

Mitigating Seabird Bycatch during Hauling by Pelagic Longline Vessels

PubMed Central

Gilman, Eric; Chaloupka, Milani; Wiedoff, Brett; Willson, Jeremy

2014-01-01

Bycatch in longline fisheries threatens the viability of some seabird populations. The Hawaii longline swordfish fishery reduced seabird captures by an order of magnitude primarily through mitigating bycatch during setting. Now, 75% of captures occur during hauling. We fit observer data to a generalized additive regression model with mixed effects to determine the significance of the effect of various factors on the standardized seabird haul catch rate. Density of albatrosses attending vessels during hauling, leader length and year had largest model effects. The standardized haul catch rate significantly increased with increased albatross density during hauling. The standardized catch rate was significantly higher the longer the leader: shorter leaders place weighted swivels closer to hooks, reducing the likelihood of baited hooks becoming available to surface-scavenging albatrosses. There was a significant linear increasing temporal trend in the standardized catch rate, possibly partly due to an observed increasing temporal trend in the local abundance of albatrosses attending vessels during hauling. Swivel weight, Beaufort scale and season were also significant but smaller model effects. Most (81%) haul captures were on branchlines actively being retrieved. Future haul mitigation research should therefore focus on reducing bird access to hooks as crew coil branchlines, including methods identified here of shorter leaders and heavier swivels, and other potentially effective methods, including faster branchline coiling and shielding the area where hooks becomes accessible. The proportion of Laysan albatross (Phoebastria immutabilis) captures that occurred during hauling was significantly, 1.6 times, higher than for black-footed albatrosses (P. nigripes), perhaps due to differences in the time of day of foraging and in daytime scavenging competitiveness; mitigating haul bycatch would therefore be a larger benefit to Laysans. Locally, findings identify opportunities to nearly eliminate seabird bycatch. Globally, findings fill a gap in knowledge of methods to mitigate seabird bycatch during pelagic longline hauling. PMID:24400096

Carotid Artery Stenting

PubMed Central

2018-01-01

Carotid artery stenosis is relatively common and is a significant cause of ischemic stroke, but carotid revascularization can reduce the risk of ischemic stroke in patients with significant symptomatic stenosis. Carotid endarterectomy has been and remains the gold standard treatment to reduce the risk of carotid artery stenosis. Carotid artery stenting (CAS) (or carotid artery stent implantation) is another method of carotid revascularization, which has developed rapidly over the last 30 years. To date, the frequency of use of CAS is increasing, and clinical outcomes are improving with technical advancements. However, the value of CAS remains unclear in patients with significant carotid artery stenosis. This review article discusses the basic concepts and procedural techniques involved in CAS. PMID:29171201

A simple method to reduce discharge of sewage microorganisms from an Antarctic research station.

PubMed

Hughes, Kevin A; Blenkharn, Nigel

2003-03-01

The majority of coastal Antarctic stations release untreated sewage into the near-shore marine environment. This study examined bacterial reproduction within the temporary sewage-holding tanks of Rothera Research Station (Adelaide Island, Antarctic Peninsula) and monitored sewage pollution in the local marine environment. By continuously flushing the sewage-holding tanks with cold seawater we inhibited microbial reproduction and decreased the numbers of bacteria subsequently released into the sea by >90%. The widespread use of this simple method could significantly reduce the numbers of faecal coliform and other non-native microorganisms introduced into the Antarctic marine environment.

Geodesic denoising for optical coherence tomography images

NASA Astrophysics Data System (ADS)

Shahrian Varnousfaderani, Ehsan; Vogl, Wolf-Dieter; Wu, Jing; Gerendas, Bianca S.; Simader, Christian; Langs, Georg; Waldstein, Sebastian M.; Schmidt-Erfurth, Ursula

2016-03-01

Optical coherence tomography (OCT) is an optical signal acquisition method capturing micrometer resolution, cross-sectional three-dimensional images. OCT images are used widely in ophthalmology to diagnose and monitor retinal diseases such as age-related macular degeneration (AMD) and Glaucoma. While OCT allows the visualization of retinal structures such as vessels and retinal layers, image quality and contrast is reduced by speckle noise, obfuscating small, low intensity structures and structural boundaries. Existing denoising methods for OCT images may remove clinically significant image features such as texture and boundaries of anomalies. In this paper, we propose a novel patch based denoising method, Geodesic Denoising. The method reduces noise in OCT images while preserving clinically significant, although small, pathological structures, such as fluid-filled cysts in diseased retinas. Our method selects optimal image patch distribution representations based on geodesic patch similarity to noisy samples. Patch distributions are then randomly sampled to build a set of best matching candidates for every noisy sample, and the denoised value is computed based on a geodesic weighted average of the best candidate samples. Our method is evaluated qualitatively on real pathological OCT scans and quantitatively on a proposed set of ground truth, noise free synthetic OCT scans with artificially added noise and pathologies. Experimental results show that performance of our method is comparable with state of the art denoising methods while outperforming them in preserving the critical clinically relevant structures.

Evaluation of fluorescence in situ hybridization techniques to study long non-coding RNA expression in cultured cells

PubMed Central

Soares, Ricardo J; Maglieri, Giulia; Gutschner, Tony; Lund, Anders H; Nielsen, Boye S

2018-01-01

Abstract Deciphering the functions of long non-coding RNAs (lncRNAs) is facilitated by visualization of their subcellular localization using in situ hybridization (ISH) techniques. We evaluated four different ISH methods for detection of MALAT1 and CYTOR in cultured cells: a multiple probe detection approach with or without enzymatic signal amplification, a branched-DNA (bDNA) probe and an LNA-modified probe with enzymatic signal amplification. All four methods adequately stained MALAT1 in the nucleus in all of three cell lines investigated, HeLa, NHDF and T47D, and three of the methods detected the less expressed CYTOR. The sensitivity of the four ISH methods was evaluated by image analysis. In all three cell lines, the two methods involving enzymatic amplification gave the most intense MALAT1 signal, but the signal-to-background ratios were not different. CYTOR was best detected using the bDNA method. All four ISH methods showed significantly reduced MALAT1 signal in knock-out cells, and siRNA-induced knock-down of CYTOR resulted in significantly reduced CYTOR ISH signal, indicating good specificity of the probe designs and detection systems. Our data suggest that the ISH methods allow detection of both abundant and less abundantly expressed lncRNAs, although the latter required the use of the most specific and sensitive probe detection system. PMID:29059327

Off-flavor related volatiles in soymilk as affected by soybean variety, grinding, and heat-processing methods.

PubMed

Zhang, Yan; Guo, Shuntang; Liu, Zhisheng; Chang, Sam K C

2012-08-01

Off-flavor of soymilk is a barrier to the acceptance of consumers. The objectionable soy odor can be reduced through inhibition of their formation or through removal after being formed. In this study, soymilk was prepared by three grinding methods (ambient, cold, and hot grinding) from two varieties (yellow Prosoy and a black soybean) before undergoing three heating processes: stove cooking, one-phase UHT (ultrahigh temperature), and two-phase UHT process using a Microthermics direct injection processor, which was equipped with a vacuuming step to remove injected water and volatiles. Eight typical soy odor compounds, generated from lipid oxidation, were extracted by a solid-phase microextraction method and analyzed by gas chromatography. The results showed that hot grinding and cold grinding significantly reduced off-flavor as compared with ambient grinding, and hot grinding achieved the best result. The UHT methods, especially the two-phase UHT method, were effective to reduce soy odor. Different odor compounds showed distinct concentration patterns because of different formation mechanisms. The two varieties behaved differently in odor formation during the soymilk-making process. Most odor compounds could be reduced to below the detection limit through a combination of hot grinding and two-phase UHT processing. However, hot grinding gave lower solid and protein recoveries in soymilk.

Improving multi-objective reservoir operation optimization with sensitivity-informed dimension reduction

NASA Astrophysics Data System (ADS)

Chu, J.; Zhang, C.; Fu, G.; Li, Y.; Zhou, H.

2015-08-01

This study investigates the effectiveness of a sensitivity-informed method for multi-objective operation of reservoir systems, which uses global sensitivity analysis as a screening tool to reduce computational demands. Sobol's method is used to screen insensitive decision variables and guide the formulation of the optimization problems with a significantly reduced number of decision variables. This sensitivity-informed method dramatically reduces the computational demands required for attaining high-quality approximations of optimal trade-off relationships between conflicting design objectives. The search results obtained from the reduced complexity multi-objective reservoir operation problems are then used to pre-condition the full search of the original optimization problem. In two case studies, the Dahuofang reservoir and the inter-basin multi-reservoir system in Liaoning province, China, sensitivity analysis results show that reservoir performance is strongly controlled by a small proportion of decision variables. Sensitivity-informed dimension reduction and pre-conditioning are evaluated in their ability to improve the efficiency and effectiveness of multi-objective evolutionary optimization. Overall, this study illustrates the efficiency and effectiveness of the sensitivity-informed method and the use of global sensitivity analysis to inform dimension reduction of optimization problems when solving complex multi-objective reservoir operation problems.

Shielding methods of quasilaminar jets outflowing from plasma torch with interelectrode insert

NASA Astrophysics Data System (ADS)

Solonenko, O. P.; Smirnov, A. V.

2017-05-01

Investigations of two methods of protection against mixing of surrounding air atmosphere with the free lengthy jets outflowing at low Reynolds numbers from plasma torches with interelectrode insertion (IEI) were carried out. The offered methods allow to significantly reduce the mixing of oxygen with plasma jets that gives a possibility of synthesis, treatment and spraying of powder materials, as well as melting of coatings critical to oxidation.

Optimal subsystem approach to multi-qubit quantum state discrimination and experimental investigation

NASA Astrophysics Data System (ADS)

Xue, ShiChuan; Wu, JunJie; Xu, Ping; Yang, XueJun

2018-02-01

Quantum computing is a significant computing capability which is superior to classical computing because of its superposition feature. Distinguishing several quantum states from quantum algorithm outputs is often a vital computational task. In most cases, the quantum states tend to be non-orthogonal due to superposition; quantum mechanics has proved that perfect outcomes could not be achieved by measurements, forcing repetitive measurement. Hence, it is important to determine the optimum measuring method which requires fewer repetitions and a lower error rate. However, extending current measurement approaches mainly aiming at quantum cryptography to multi-qubit situations for quantum computing confronts challenges, such as conducting global operations which has considerable costs in the experimental realm. Therefore, in this study, we have proposed an optimum subsystem method to avoid these difficulties. We have provided an analysis of the comparison between the reduced subsystem method and the global minimum error method for two-qubit problems; the conclusions have been verified experimentally. The results showed that the subsystem method could effectively discriminate non-orthogonal two-qubit states, such as separable states, entangled pure states, and mixed states; the cost of the experimental process had been significantly reduced, in most circumstances, with acceptable error rate. We believe the optimal subsystem method is the most valuable and promising approach for multi-qubit quantum computing applications.

Simplified methods for calculating photodissociation rates

NASA Technical Reports Server (NTRS)

Shimazaki, T.; Ogawa, T.; Farrell, B. C.

1977-01-01

Simplified methods for calculating the transmission of solar UV radiation and the dissociation coefficients of various molecules are compared. A significant difference sometimes appears in calculations of the individual band, but the total transmission and the total dissociation coefficients integrated over the entire SR (solar radiation) band region agree well between the methods. The ambiguities in the solar flux data affect the calculated dissociation coefficients more strongly than does the method. A simpler method is developed for the purpose of reducing the computation time and computer memory size necessary for storing coefficients of the equations. The new method can reduce the computation time by a factor of more than 3 and the memory size by a factor of more than 50 compared with the Hudson-Mahle method, and yet the result agrees within 10 percent (in most cases much less) with the original Hudson-Mahle results, except for H2O and CO2. A revised method is necessary for these two molecules, whose absorption cross sections change very rapidly over the SR band spectral range.

Subsampled Hessian Newton Methods for Supervised Learning.

PubMed

Wang, Chien-Chih; Huang, Chun-Heng; Lin, Chih-Jen

2015-08-01

Newton methods can be applied in many supervised learning approaches. However, for large-scale data, the use of the whole Hessian matrix can be time-consuming. Recently, subsampled Newton methods have been proposed to reduce the computational time by using only a subset of data for calculating an approximation of the Hessian matrix. Unfortunately, we find that in some situations, the running speed is worse than the standard Newton method because cheaper but less accurate search directions are used. In this work, we propose some novel techniques to improve the existing subsampled Hessian Newton method. The main idea is to solve a two-dimensional subproblem per iteration to adjust the search direction to better minimize the second-order approximation of the function value. We prove the theoretical convergence of the proposed method. Experiments on logistic regression, linear SVM, maximum entropy, and deep networks indicate that our techniques significantly reduce the running time of the subsampled Hessian Newton method. The resulting algorithm becomes a compelling alternative to the standard Newton method for large-scale data classification.

Impact of SMS/GPRS Printers in Reducing Time to Early Infant Diagnosis Compared With Routine Result Reporting: A Systematic Review and Meta-Analysis

PubMed Central

Markby, Jessica; Boeke, Caroline; Penazzato, Martina; Urick, Brittany; Ghadrshenas, Anisa; Harris, Lindsay; Ford, Nathan; Peter, Trevor

2017-01-01

Background: Despite significant gains made toward improving access, early infant diagnosis (EID) testing programs suffer from long test turnaround times that result in substantial loss to follow-up and mortality associated with delays in antiretroviral therapy initiation. These delays in treatment initiation are particularly impactful because of significant HIV-related infant mortality observed by 2–3 months of age. Short message service (SMS) and general packet radio service (GPRS) printers allow test results to be transmitted immediately to health care facilities on completion of testing in the laboratory. Methods: We conducted a systematic review and meta-analysis to assess the benefit of using SMS/GPRS printers to increase the efficiency of EID test result delivery compared with traditional courier paper–based results delivery methods. Results: We identified 11 studies contributing data for over 16,000 patients from East and Southern Africa. The test turnaround time from specimen collection to result received at the health care facility with courier paper–based methods was 68.0 days (n = 6835), whereas the test turnaround time with SMS/GPRS printers was 51.1 days (n = 6711), resulting in a 2.5-week (25%) reduction in the turnaround time. Conclusions: Courier paper–based EID test result delivery methods are estimated to add 2.5 weeks to EID test turnaround times in low resource settings and increase the risk that infants receive test results during or after the early peak of infant mortality. SMS/GPRS result delivery to health care facility printers significantly reduced test turnaround time and may reduce this risk. SMS/GPRS printers should be considered for expedited delivery of EID and other centralized laboratory test results. PMID:28825941

Magnetic human body communication.

PubMed

Park, Jiwoong; Mercier, Patrick P

2015-01-01

This paper presents a new human body communication (HBC) technique that employs magnetic resonance for data transfer in wireless body-area networks (BANs). Unlike electric field HBC (eHBC) links, which do not necessarily travel well through many biological tissues, the proposed magnetic HBC (mHBC) link easily travels through tissue, offering significantly reduced path loss and, as a result, reduced transceiver power consumption. In this paper the proposed mHBC concept is validated via finite element method simulations and measurements. It is demonstrated that path loss across the body under various postures varies from 10-20 dB, which is significantly lower than alternative BAN techniques.

Flooded Underground Coal Mines: A Significant Source of Inexpensive Geothermal Energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watzlaf, G.R.; Ackman, T.E.

2007-04-01

Many mining regions in the United States contain extensive areas of flooded underground mines. The water within these mines represents a significant and widespread opportunity for extracting low-grade, geothermal energy. Based on current energy prices, geothermal heat pump systems using mine water could reduce the annual costs for heating to over 70 percent compared to conventional heating methods (natural gas or heating oil). These same systems could reduce annual cooling costs by up to 50 percent over standard air conditioning in many areas of the country. (Formatted full-text version is released by permission of publisher)

Complementary Reliability-Based Decodings of Binary Linear Block Codes

NASA Technical Reports Server (NTRS)

Fossorier, Marc P. C.; Lin, Shu

1997-01-01

This correspondence presents a hybrid reliability-based decoding algorithm which combines the reprocessing method based on the most reliable basis and a generalized Chase-type algebraic decoder based on the least reliable positions. It is shown that reprocessing with a simple additional algebraic decoding effort achieves significant coding gain. For long codes, the order of reprocessing required to achieve asymptotic optimum error performance is reduced by approximately 1/3. This significantly reduces the computational complexity, especially for long codes. Also, a more efficient criterion for stopping the decoding process is derived based on the knowledge of the algebraic decoding solution.

A Universal Rig for Supporting Large Hammer Drills: Reduced Injury Risk and Improved Productivity

PubMed Central

Rempel, David; Barr, Alan

2015-01-01

Drilling holes into concrete with heavy hammer and rock drills is one of the most physically demanding tasks performed in commercial construction and poses risks for musculoskeletal disorders, noise induced hearing loss, hand arm vibration syndrome and silicosis. The aim of this study was to (1) use a participatory process to develop a rig to support pneumatic rock drills or large electric hammer drills in order to reduce the health risks and (2) evaluate the usability of the rig. Seven prototype rigs for supporting large hammer drills were developed and modified with feedback from commercial contractors and construction workers. The final design was evaluated by laborers and electricians (N=29) who performed their usual concrete drilling with the usual method and the new rig. Subjective regional fatigue was significantly less in the neck, shoulders, hands and arms, and lower back) when using the universal rig compared to the usual manual method. Usability ratings for the rig were significantly better than the usual method on stability, control, drilling, accuracy, and vibration. Drilling time was reduced by approximately 50% with the rig. Commercial construction contractors, laborers and electricians who use large hammer drills for drilling many holes should consider using such a rig to prevent musculoskeletal disorders, fatigue, and silicosis. PMID:26005290

Putaminal volume and diffusion in early familial Creutzfeldt-Jakob disease.

PubMed

Seror, Ilana; Lee, Hedok; Cohen, Oren S; Hoffmann, Chen; Prohovnik, Isak

2010-01-15

The putamen is centrally implicated in the pathophysiology of Creutzfeldt-Jakob Disease (CJD). To our knowledge, its volume has never been measured in this disease. We investigated whether gross putaminal atrophy can be detected by MRI in early stages, when the diffusion is already reduced. Twelve familial CJD patients with the E200K mutation and 22 healthy controls underwent structural and diffusion MRI scans. The putamen was identified in anatomical scans by two methods: manual tracing by a blinded investigator, and automatic parcellation by a computerized segmentation procedure (FSL FIRST). For each method, volume and mean Apparent Diffusion Coefficient (ADC) were calculated. ADC was significantly lower in CJD patients (697+/-64 microm(2)/s vs. 750+/-31 microm(2)/s, p<0.005), as expected, but the volume was not reduced. The computerized FIRST delineation yielded comparable ADC values to the manual method, but computerized volumes were smaller than manual tracing values. We conclude that significant diffusion reduction in the putamen can be detected by delineating the structure manually or with a computerized algorithm. Our findings confirm and extend previous voxel-based and observational studies. Putaminal volume was not reduced in our early-stage patients, thus confirming that diffusion abnormalities precede detectible atrophy in this structure.

Strategic assay deployment as a method for countering analytical bottlenecks in high throughput process development: case studies in ion exchange chromatography.

PubMed

Konstantinidis, Spyridon; Heldin, Eva; Chhatre, Sunil; Velayudhan, Ajoy; Titchener-Hooker, Nigel

2012-01-01

High throughput approaches to facilitate the development of chromatographic separations have now been adopted widely in the biopharmaceutical industry, but issues of how to reduce the associated analytical burden remain. For example, acquiring experimental data by high level factorial designs in 96 well plates can place a considerable strain upon assay capabilities, generating a bottleneck that limits significantly the speed of process characterization. This article proposes an approach designed to counter this challenge; Strategic Assay Deployment (SAD). In SAD, a set of available analytical methods is investigated to determine which set of techniques is the most appropriate to use and how best to deploy these to reduce the consumption of analytical resources while still enabling accurate and complete process characterization. The approach is demonstrated by investigating how salt concentration and pH affect the binding of green fluorescent protein from Escherichia coli homogenate to an anion exchange resin presented in a 96-well filter plate format. Compared with the deployment of routinely used analytical methods alone, the application of SAD reduced both the total assay time and total assay material consumption by at least 40% and 5%, respectively. SAD has significant utility in accelerating bioprocess development activities. Copyright © 2012 American Institute of Chemical Engineers (AIChE).

Exercise reduces depressive symptoms in adults with arthritis: Evidential value

PubMed Central

Kelley, George A; Kelley, Kristi S

2016-01-01

AIM To determine whether evidential value exists that exercise reduces depression in adults with arthritis and other rheumatic conditions. METHODS Utilizing data derived from a prior meta-analysis of 29 randomized controlled trials comprising 2449 participants (1470 exercise, 979 control) with fibromyalgia, osteoarthritis, rheumatoid arthritis or systemic lupus erythematosus, a new method, P-curve, was utilized to assess for evidentiary worth as well as dismiss the possibility of discriminating reporting of statistically significant results regarding exercise and depression in adults with arthritis and other rheumatic conditions. Using the method of Stouffer, Z-scores were calculated to examine selective-reporting bias. An alpha (P) value < 0.05 was deemed statistically significant. In addition, average power of the tests included in P-curve, adjusted for publication bias, was calculated. RESULTS Fifteen of 29 studies (51.7%) with exercise and depression results were statistically significant (P < 0.05) while none of the results were statistically significant with respect to exercise increasing depression in adults with arthritis and other rheumatic conditions. Right-skew to dismiss selective reporting was identified (Z = −5.28, P < 0.0001). In addition, the included studies did not lack evidential value (Z = 2.39, P = 0.99), nor did they lack evidential value and were P-hacked (Z = 5.28, P > 0.99). The relative frequencies of P-values were 66.7% at 0.01, 6.7% each at 0.02 and 0.03, 13.3% at 0.04 and 6.7% at 0.05. The average power of the tests included in P-curve, corrected for publication bias, was 69%. Diagnostic plot results revealed that the observed power estimate was a better fit than the alternatives. CONCLUSION Evidential value results provide additional support that exercise reduces depression in adults with arthritis and other rheumatic conditions. PMID:27489782

The impact of education and cooking methods on serum phosphate levels in patients on hemodialysis: 1-year study.

PubMed

Vrdoljak, Ivica; Panjkota Krbavčić, Ines; Bituh, Martina; Leko, Ninoslav; Pavlović, Draško; Vrdoljak Margeta, Tea

2017-04-01

Control of serum phosphate is important for patients on hemodialysis. The aim of the study was to determine if education based on phosphorus-reducing techniques in food preparation and thermal processing, and accordingly prepared and applied diets, will lead to better outcomes than a standard education program to improve phosphate control in patients on hemodialysis. Forty-seven patients on hemodialysis were divided between an intervention and a control group. All subjects received training about nutrition for hemodialysis patients by trained dietitian. In addition, subjects in the intervention group received additional training in phosphorus-reducing techniques in food preparation and received two hospital meals prepared using suggested cooking methods to reduce the phosphate content of food during dialysis treatment. Serum phosphate, serum albumin, and anthropometric parameters were measured, while nPCR was calculated, at the baseline and during the 1-year study. No differences in serum phosphate levels were observed between intervention (1.68 mmol/L [1.48-2.03]) and control group (1.88 mmol/L [1.57-2.2]) at baseline (P = 0.130). Although not statistically significant between groups the mean reduction was more apparent in the intervention group (-0.3 mmol/L (-0.4 to 0.1) vs. -0.2 (-0.5 to 0.1)), and lead to significantly reduction of phosphate binder therapy. During the study, the nPCR and anthropometric status of the patients did not change significantly. Providing additional education to hemodialysis patients on the specific cooking methods and accordingly prepared meals may decrease serum phosphate levels without significantly affecting nutritional status which may be useful in helping to prevent and treat hyperphosphatemia. © 2016 International Society for Hemodialysis.

The Misgav Ladach method for cesarean section compared to the Pfannenstiel method.

PubMed

Darj, E; Nordström, M L

1999-01-01

The aim of the study was to evaluate the outcome of two different methods of cesarean section (CS). The study was designed as a prospective, randomized, controlled trial. All CS were performed at the University Hospital in Uppsala, Sweden. Fifty women admitted to hospital for a first elective CS were consecutively included in the study. They were randomly allocated to two groups. One group was operated on by the Misgav Ladach method for CS and the other group by the Pfannenstiel method. All operations were performed by the same surgeon. Duration of operation, amount of bleeding, analgesics required, scar appearance and length of hospitalization. Operating time was significantly different between the two methods, with an average of 12.5 minutes with the Misgav Ladach method and 26 minutes with the Pfannenstiel method (p<0.001). The amount of blood loss differed significantly, with 448 ml and 608 ml respectively (p=0.017). Significantly less analgesic injections and tablets (p=0.004) were needed after the Misgav Ladach method. The Misgav Ladach method of CS has advantages over the Pfannenstiel method by being significantly quicker to perform, with a reduced amount of bleeding and diminished postoperative pain. The women were satisfied with the appearance of their scars. In this study no negative effects of the new operation technique were discovered.

Preparing thermoplastic aromatic polyimides

NASA Technical Reports Server (NTRS)

Bell, V. L.

1973-01-01

Method prepares aromatic polyimides with significantly reduced glass-transition temperatures and without accompanying loss of high-level thermo-oxidative stability which has been typical. This has been made possible by use of diamine monomers with specific stereoisomeric features.

Method for rapidly producing microporous and mesoporous materials

DOEpatents

Coronado, P.R.; Poco, J.F.; Hrubesh, L.W.; Hopper, R.W.

1997-11-11

An improved, rapid process is provided for making microporous and mesoporous materials, including aerogels and pre-ceramics. A gel or gel precursor is confined in a sealed vessel to prevent structural expansion of the gel during the heating process. This confinement allows the gelation and drying processes to be greatly accelerated, and significantly reduces the time required to produce a dried aerogel compared to conventional methods. Drying may be performed either by subcritical drying with a pressurized fluid to expel the liquid from the gel pores or by supercritical drying. The rates of heating and decompression are significantly higher than for conventional methods. 3 figs.

Effect of Resin-modified Glass Ionomer Cement Dispensing/Mixing Methods on Mechanical Properties.

PubMed

Sulaiman, T A; Abdulmajeed, A A; Altitinchi, A; Ahmed, S N; Donovan, T E

2018-03-23

Resin-modified glass ionomer cements (RMGIs) are often used for luting indirect restorations. Hand-mixing traditional cements demands significant time and may be technique sensitive. Efforts have been made by manufacturers to introduce the same cement using different dispensing/mixing methods. It is not known what effects these changes may have on the mechanical properties of the dental cement. The purpose of this study was to evaluate the mechanical properties (diametral tensile strength [DTS], compressive strength [CS], and fracture toughness [FT]) of RMGIs with different dispensing/mixing systems. The RMGI specimens (n=14)-RelyX Luting (hand mix), RelyX Luting Plus (clicker-hand mix), RelyX Luting Plus (automix) (3M ESPE), GC Fuji PLUS (capsule-automix), and GC FujiCEM 2 (automix) (GC)-were prepared for each mechanical test and examined after thermocycling (n=7/subgroup) for 20,000 cycles to the following: DTS, CS (ISO 9917-1) and FT (ISO standard 6872; Single-edge V-notched beam method). Specimens were mounted and loaded with a universal testing machine until failure occurred. Two-/one-way analysis of variance followed by Tukey honestly significantly different post hoc test was used to analyze data for statistical significance ( p<0.05). The interaction effect of both dispensing/mixing method and thermocycling was significant only for the CS test of the GC group ( p<0.05). The different dispensing/mixing methods had no effect on the DTS of the tested cements. The CS of GC Fuji PLUS was significantly higher than that of the automix version ( p<0.05). The FT decreased significantly when switching from RelyX (hand mix) to RelyX Luting Plus (clicker-hand mix) and to RelyX Luting Plus (automix) ( p<0.05). Except in the case of the DTS of the GC group and the CS of GC Fuji PLUS, thermocycling had a significant effect reducing the mechanical properties of the RMGI cements ( p<0.05). Introducing alternative dispensing/mixing methods for mixing RMGIs to reduce time and technique sensitivity may affect mechanical properties and is brand dependent.

Compressible flows with periodic vortical disturbances around lifting airfoils. Ph.D. Thesis - Notre Dame Univ.

NASA Technical Reports Server (NTRS)

Scott, James R.

1991-01-01

A numerical method is developed for solving periodic, three-dimensional, vortical flows around lifting airfoils in subsonic flow. The first-order method that is presented fully accounts for the distortion effects of the nonuniform mean flow on the convected upstream vortical disturbances. The unsteady velocity is split into a vortical component which is a known function of the upstream flow conditions and the Lagrangian coordinates of the mean flow, and an irrotational field whose potential satisfies a nonconstant-coefficient, inhomogeneous, convective wave equation. Using an elliptic coordinate transformation, the unsteady boundary value problem is solved in the frequency domain on grids which are determined as a function of the Mach number and reduced frequency. The numerical scheme is validated through extensive comparisons with known solutions to unsteady vortical flow problems. In general, it is seen that the agreement between the numerical and analytical results is very good for reduced frequencies ranging from 0 to 4, and for Mach numbers ranging from .1 to .8. Numerical results are also presented for a wide variety of flow configurations for the purpose of determining the effects of airfoil thickness, angle of attack, camber, and Mach number on the unsteady lift and moment of airfoils subjected to periodic vortical gusts. It is seen that each of these parameters can have a significant effect on the unsteady airfoil response to the incident disturbances, and that the effect depends strongly upon the reduced frequency and the dimensionality of the gust. For a one-dimensional (transverse) or two-dimensional (transverse and longitudinal) gust, the results indicate that airfoil thickness increases the unsteady lift and moment at the low reduced frequencies but decreases it at the high reduced frequencies. The results show that an increase in airfoil Mach number leads to a significant increase in the unsteady lift and moment for the low reduced frequencies, but a significant decrease for the high reduced frequencies.

Method and apparatus for measuring irradiated fuel profiles

DOEpatents

Lee, David M.

1982-01-01

A new apparatus is used to substantially instantaneously obtain a profile of an object, for example a spent fuel assembly, which profile (when normalized) has unexpectedly been found to be substantially identical to the normalized profile of the burnup monitor Cs-137 obtained with a germanium detector. That profile can be used without normalization in a new method of identifying and monitoring in order to determine for example whether any of the fuel has been removed. Alternatively, two other new methods involve calibrating that profile so as to obtain a determination of fuel burnup (which is important for complying with safeguards requirements, for utilizing fuel to an optimal extent, and for storing spent fuel in a minimal amount of space). Using either of these two methods of determining burnup, one can reduce the required measurement time significantly (by more than an order of magnitude) over existing methods, yet retain equal or only slightly reduced accuracy.

Lossless Compression of JPEG Coded Photo Collections.

PubMed

Wu, Hao; Sun, Xiaoyan; Yang, Jingyu; Zeng, Wenjun; Wu, Feng

2016-04-06

The explosion of digital photos has posed a significant challenge to photo storage and transmission for both personal devices and cloud platforms. In this paper, we propose a novel lossless compression method to further reduce the size of a set of JPEG coded correlated images without any loss of information. The proposed method jointly removes inter/intra image redundancy in the feature, spatial, and frequency domains. For each collection, we first organize the images into a pseudo video by minimizing the global prediction cost in the feature domain. We then present a hybrid disparity compensation method to better exploit both the global and local correlations among the images in the spatial domain. Furthermore, the redundancy between each compensated signal and the corresponding target image is adaptively reduced in the frequency domain. Experimental results demonstrate the effectiveness of the proposed lossless compression method. Compared to the JPEG coded image collections, our method achieves average bit savings of more than 31%.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hiller, Mauritius M.; Veinot, Kenneth G.; Easterly, Clay E.

In this study, methods are addressed to reduce the computational time to compute organ-dose rate coefficients using Monte Carlo techniques. Several variance reduction techniques are compared including the reciprocity method, importance sampling, weight windows and the use of the ADVANTG software package. For low-energy photons, the runtime was reduced by a factor of 10 5 when using the reciprocity method for kerma computation for immersion of a phantom in contaminated water. This is particularly significant since impractically long simulation times are required to achieve reasonable statistical uncertainties in organ dose for low-energy photons in this source medium and geometry. Althoughmore » the MCNP Monte Carlo code is used in this paper, the reciprocity technique can be used equally well with other Monte Carlo codes.« less

Management of enterocutaneous fistulas and problem stomas with silicone casting of the abdominal wall defect.

PubMed

Streza, G A; Laing, B J; Gilsdorf, R B

1977-12-01

Silicone casting of abdominal wall defects around enteric fistulas in six patients and problem stomas in three patients proved to be an effective means of controlling the output of the fistulas, reducing wound care time, and reducing or eliminating parenteral nutrition needs. Outpatient management was possible in seven of the nine patients. It is observed that the wounds healed rapidly with this method of fistula control. Epithelialization occurred more rapidly than expected. This method of management may tend to make the fistulas remain open longer than by other means of care, but the significant increase in patient comfort, the financial savings, and the relative safety warrant continued utilization and observation of this method of management.

Methods for reducing pollutant emissions from jet aircraft

NASA Technical Reports Server (NTRS)

Butze, H. F.

1971-01-01

Pollutant emissions from jet aircraft and combustion research aimed at reducing these emissions are defined. The problem of smoke formation and results achieved in smoke reduction from commercial combustors are discussed. Expermental results of parametric tests performed on both conventional and experimental combustors over a range of combustor-inlet conditions are presented. Combustor design techniques for reducing pollutant emissions are discussed. Improved fuel atomization resulting from the use of air-assist fuel nozzles has brought about significant reductions in hydrocarbon and carbon monoxide emissions at idle. Diffuser tests have shown that the combustor-inlet airflow profile can be controlled through the use of diffuser-wall bleed and that it may thus be possible to reduce emissions by controlling combustor airflow distribution. Emissions of nitric oxide from a shortlength annular swirl-can combustor were significantly lower than those from a conventional combustor operating at similar conditions.

[Intragastric utilization of antacids following meals in relation to stomach emptying].

PubMed

Lux, G; Hartog, C; Ruppin, H; Lederer, P; Schmitt, W

1983-03-01

Gastric acid secretion and gastric emptying rate was measured using double marker method and continuous titration of a liquid peptone test meal. Titration rate was significantly reduced by 30 ml of an aluminiumhydroxide- and magnesiumhydroxide containing antacid compound (Maalox). Acidity of gastric contents was reduced over a period of 48.4 +/- 9.1 min (mean +/- SD; endpoint of titration pH 5.5) and 77.6 +/- 2.0 min (pH 3.5) (p less than 0.05). The histamine H2-receptor blocker Ranitidine (0.25 mg/kg b.w.) and the antimuscarinic agent Pirenzepine reduced titrable gastric acid secretion in a similar range, as far as the observation period of 90 min is concerned. Biosorbin MCT, a formula diet, stimulated gastric acid secretion half the amount of gastric acid secretion stimulated by the peptone meal. Gastric emptying rate was significantly reduced by formula diet, but not by either of the other compounds.

Improving diet recipe and cooking methods attenuates hyperphosphatemia in patients undergoing peritoneal dialysis.

PubMed

Jiang, N; Fang, W; Gu, A P; Yuan, J Z; Yang, X X; Lin, A W; Ni, Z H; Qian, J Q

2015-09-01

Hyperphosphatemia is an independent predictor for cardiovascular and all-cause mortality in patients undergoing peritoneal dialysis (PD). The study aimed to investigate the effect of dietary intervention on reducing serum phosphate concentration in hyperphosphatemic PD patients. In this single-center clinical trial, 97 prevalent PD patients with serum phosphate concentration ≥ 1.6 mmol/l were allocated to the intervention (n = 48) or control (n = 49) group and followed up for 1 year. In addition to phosphate binder (calcium carbonate) therapy, patients in the intervention group were intensively educated to reduce phosphate-rich food intake and improve cooking methods. While stable in the control group (1.97 ± 0.20 to 1.94 ± 0.35 mmol/l, p > 0.05), the serum phosphate concentration decreased significantly in the intervention group (1.98 ± 0.28 to 1.65 ± 0.33 mmol/l, p = 0.015) concurrently with the drop in dietary phosphate intake (13.03 ± 3.39 to 10.82 ± 3.00 mg/kg ideal body weight/day, p = 0.001). Moreover, after 6 months of intervention, fewer patients needed to use calcium carbonate (from 64.6% to 41.5%, p = 0.029) and the medicine dose reduced significantly (from 2.25 (0, 3.94) to 0 (0, 1.50) g/day, p < 0.001). Our data indicated that intensive dietary intervention of reducing phosphate-rich food intake and improving cooking methods attenuated hyperphosphatemia in PD patients. It suggests that regular assessment of dietary phosphate intake and modification of diet recipe and cooking methods are essential for hyperphosphatemia treatment in PD patients in addition to phosphate binder therapy. Copyright © 2015 Elsevier B.V. All rights reserved.

Selecting Sensitive Parameter Subsets in Dynamical Models With Application to Biomechanical System Identification.

PubMed

Ramadan, Ahmed; Boss, Connor; Choi, Jongeun; Peter Reeves, N; Cholewicki, Jacek; Popovich, John M; Radcliffe, Clark J

2018-07-01

Estimating many parameters of biomechanical systems with limited data may achieve good fit but may also increase 95% confidence intervals in parameter estimates. This results in poor identifiability in the estimation problem. Therefore, we propose a novel method to select sensitive biomechanical model parameters that should be estimated, while fixing the remaining parameters to values obtained from preliminary estimation. Our method relies on identifying the parameters to which the measurement output is most sensitive. The proposed method is based on the Fisher information matrix (FIM). It was compared against the nonlinear least absolute shrinkage and selection operator (LASSO) method to guide modelers on the pros and cons of our FIM method. We present an application identifying a biomechanical parametric model of a head position-tracking task for ten human subjects. Using measured data, our method (1) reduced model complexity by only requiring five out of twelve parameters to be estimated, (2) significantly reduced parameter 95% confidence intervals by up to 89% of the original confidence interval, (3) maintained goodness of fit measured by variance accounted for (VAF) at 82%, (4) reduced computation time, where our FIM method was 164 times faster than the LASSO method, and (5) selected similar sensitive parameters to the LASSO method, where three out of five selected sensitive parameters were shared by FIM and LASSO methods.

The estimation of dynamic contact angle of ultra-hydrophobic surfaces using inclined surface and impinging droplet methods

NASA Astrophysics Data System (ADS)

Jasikova, Darina; Kotek, Michal

2014-03-01

The development of industrial technology also brings with optimized surface quality, particularly where there is contact with food. Application ultra-hydrophobic surface significantly reduces the growth of bacteria and facilitates cleaning processes. Testing and evaluation of surface quality are used two methods: impinging droplet and inclined surface method optimized with high speed shadowgraphy, which give information about dynamic contact angle. This article presents the results of research into new methods of measuring ultra-hydrophobic patented technology.

[Solubilization Specificities Interferon beta-1b from Inclusion Bodies].

PubMed

Zhuravko, A S; Kononova, N V; Bobruskin, A I

2015-01-01

A new solubilization method of recombinant interferon beta-1b (IFNβ-1b) from the inclusion bodies was developed. This method allows to extract the target protein selectively in the solutions of different alcohols, such as ethanol, propanol and isopropanol. It was shown that the more effective IFNβ-1b solubilization was achieved in the 55% propanol solution. This method allowed to extract the target protein from inclusion bodies around 85-90%, and significantly reduced Escherichia coli content in the solubilizate, in comparison with standard methods.

An improved method for isolating viruses from asymptomatic carrier fish

USGS Publications Warehouse

Amend, Donald F.; Pietsch, John P.

1972-01-01

This paper describes a method using elevated levels of penicillin, streptomycin, and nystatin instead of filters to control bacteria and mold contaminants in specimens processed for virus isolation. Filters were shown to significantly reduce the virus concentration. Virus and tissue cultures were not affected by this procedure. In field tests nearly three times more specimens were positive for virus with this method than with the widely used filter technique. Moreover, the cost of materials was less. This method is recommended for inspection and certification purposes.

Monitoring Corrosion of Steel Bars in Reinforced Concrete Structures

PubMed Central

Verma, Sanjeev Kumar; Bhadauria, Sudhir Singh; Akhtar, Saleem

2014-01-01

Corrosion of steel bars embedded in reinforced concrete (RC) structures reduces the service life and durability of structures causing early failure of structure, which costs significantly for inspection and maintenance of deteriorating structures. Hence, monitoring of reinforcement corrosion is of significant importance for preventing premature failure of structures. This paper attempts to present the importance of monitoring reinforcement corrosion and describes the different methods for evaluating the corrosion state of RC structures, especially hal-cell potential (HCP) method. This paper also presents few techniques to protect concrete from corrosion. PMID:24558346

Monitoring corrosion of steel bars in reinforced concrete structures.

PubMed

Verma, Sanjeev Kumar; Bhadauria, Sudhir Singh; Akhtar, Saleem

2014-01-01

Corrosion of steel bars embedded in reinforced concrete (RC) structures reduces the service life and durability of structures causing early failure of structure, which costs significantly for inspection and maintenance of deteriorating structures. Hence, monitoring of reinforcement corrosion is of significant importance for preventing premature failure of structures. This paper attempts to present the importance of monitoring reinforcement corrosion and describes the different methods for evaluating the corrosion state of RC structures, especially hal-cell potential (HCP) method. This paper also presents few techniques to protect concrete from corrosion.

Comparison of three methods to reduce energy density. Effects on daily energy intake.

PubMed

Williams, Rachel A; Roe, Liane S; Rolls, Barbara J

2013-07-01

Reductions in food energy density can decrease energy intake, but it is not known if the effects depend on the way that energy density is reduced. We investigated whether three methods of reducing energy density (decreasing fat, increasing fruit and vegetables, and adding water) differed in their effects on energy intake across the day. In a crossover design, 59 adults ate breakfast, lunch, and dinner in the laboratory once a week for 4 weeks. Across conditions, the entrées were either standard in energy density or were reduced in energy density by 20% using one of the three methods. Each meal included a manipulated entrée along with unmanipulated side dishes, and all foods were consumed ad libitum. Reducing the energy density of entrées significantly decreased daily energy intake compared to standard entrées (mean intake 2667 ± 77 kcal/day; 11,166 ± 322 kJ/day). The mean decrease was 396 ± 44 kcal/day (1658 ± 184 kJ/day) when fat was reduced, 308 ± 41 kcal/day (1290 ± 172 kJ/day) when fruit and vegetables were increased, and 230 ± 35 kcal/day (963 ± 147 kJ/day) when water was added. Daily energy intake was lower when fat was decreased compared to the other methods. These findings indicate that a variety of diet compositions can be recommended to reduce overall dietary energy density in order to moderate energy intake. Copyright © 2013 Elsevier Ltd. All rights reserved.

An improved multilevel Monte Carlo method for estimating probability distribution functions in stochastic oil reservoir simulations

DOE PAGES

Lu, Dan; Zhang, Guannan; Webster, Clayton G.; ...

2016-12-30

In this paper, we develop an improved multilevel Monte Carlo (MLMC) method for estimating cumulative distribution functions (CDFs) of a quantity of interest, coming from numerical approximation of large-scale stochastic subsurface simulations. Compared with Monte Carlo (MC) methods, that require a significantly large number of high-fidelity model executions to achieve a prescribed accuracy when computing statistical expectations, MLMC methods were originally proposed to significantly reduce the computational cost with the use of multifidelity approximations. The improved performance of the MLMC methods depends strongly on the decay of the variance of the integrand as the level increases. However, the main challengemore » in estimating CDFs is that the integrand is a discontinuous indicator function whose variance decays slowly. To address this difficult task, we approximate the integrand using a smoothing function that accelerates the decay of the variance. In addition, we design a novel a posteriori optimization strategy to calibrate the smoothing function, so as to balance the computational gain and the approximation error. The combined proposed techniques are integrated into a very general and practical algorithm that can be applied to a wide range of subsurface problems for high-dimensional uncertainty quantification, such as a fine-grid oil reservoir model considered in this effort. The numerical results reveal that with the use of the calibrated smoothing function, the improved MLMC technique significantly reduces the computational complexity compared to the standard MC approach. Finally, we discuss several factors that affect the performance of the MLMC method and provide guidance for effective and efficient usage in practice.« less

Super-Resolution Image Reconstruction Applied to Medical Ultrasound

NASA Astrophysics Data System (ADS)

Ellis, Michael

Ultrasound is the preferred imaging modality for many diagnostic applications due to its real-time image reconstruction and low cost. Nonetheless, conventional ultrasound is not used in many applications because of limited spatial resolution and soft tissue contrast. Most commercial ultrasound systems reconstruct images using a simple delay-and-sum architecture on receive, which is fast and robust but does not utilize all information available in the raw data. Recently, more sophisticated image reconstruction methods have been developed that make use of far more information in the raw data to improve resolution and contrast. One such method is the Time-Domain Optimized Near-Field Estimator (TONE), which employs a maximum a priori estimation to solve a highly underdetermined problem, given a well-defined system model. TONE has been shown to significantly improve both the contrast and resolution of ultrasound images when compared to conventional methods. However, TONE's lack of robustness to variations from the system model and extremely high computational cost hinder it from being readily adopted in clinical scanners. This dissertation aims to reduce the impact of TONE's shortcomings, transforming it from an academic construct to a clinically viable image reconstruction algorithm. By altering the system model from a collection of individual hypothetical scatterers to a collection of weighted, diffuse regions, dTONE is able to achieve much greater robustness to modeling errors. A method for efficient parallelization of dTONE is presented that reduces reconstruction time by more than an order of magnitude with little loss in image fidelity. An alternative reconstruction algorithm, called qTONE, is also developed and is able to reduce reconstruction times by another two orders of magnitude while simultaneously improving image contrast. Each of these methods for improving TONE are presented, their limitations are explored, and all are used in concert to reconstruct in vivo images of a human testicle. In all instances, the methods presented here outperform conventional image reconstruction methods by a significant margin. As TONE and its variants are general image reconstruction techniques, the theories and research presented here have the potential to significantly improve not only ultrasound's clinical utility, but that of other imaging modalities as well.

High pressure processing alters water distribution enabling the production of reduced-fat and reduced-salt pork sausages.

PubMed

Yang, Huijuan; Han, Minyi; Bai, Yun; Han, Yanqing; Xu, Xinglian; Zhou, Guanghong

2015-04-01

High pressure processing (HPP) was used to explore novel methods for modifying the textural properties of pork sausages with reduced-salt, reduced-fat and no fat replacement additions. A 2×7 factorial design was set up, incorporating two pressure levels (0.1 or 200 MPa) and seven fat levels (0, 5, 10, 15, 20, 25 and 30%). Sausages treated at 200 MPa exhibited improved tenderness at all fat levels compared with 0.1 MPa treated samples, and the shear force of sausages treated at 200 MPa with 15 or 20% fat content was similar to the 0.1 MPa treated sausages with 30% fat. HPP significantly changed the P₂ peak ratio of the four water components in raw sausages, resulting in improved textural properties of emulsion-type sausages with reduced-fat and reduced-salt. Significant correlations were found between pH, color, shear force and water proportions. The scanning and transmission micrographs revealed the formation of smaller fat globules and an improved network structure in the pressure treated sausages. In conclusion, there is potential to manufacture sausages with reduced-fat and reduced-salt by using HPP to maintain textural qualities. Copyright © 2014. Published by Elsevier Ltd.

GUIDE TO CLEANER TECHNOLOGIES: ORGANIC COATING REMOVAL

EPA Science Inventory

A cleaner technology is a source reduction or recycle method |applied to eliminate or significantly reduce hazardous waste generation. Source reduction includes product changes and source control. Source control can be further characterized as input material changes, technology...

Effects of Cold and Compression on Edema.

ERIC Educational Resources Information Center

Sloan, J. P.; And Others

1988-01-01

Investigation of ways to treat artificially induced acute inflammatory reactions in human tissue found that neither cooling or pressure alone reduced the swelling, while a combination of the two methods produced a significant reduction in swelling. (Author/CB)

Process for using surface strain measurements to obtain operational loads for complex structures

NASA Technical Reports Server (NTRS)

Ko, William L. (Inventor); Richards, William Lance (Inventor)

2010-01-01

The invention is an improved process for using surface strain data to obtain real-time, operational loads data for complex structures that significantly reduces the time and cost versus current methods.

Mental Illness Stigma Intervention in African Americans: Examining Two Delivery Methods.

PubMed

Vinson, Ebony S; Abdullah, Tahirah; Brown, Tamara L

2016-05-01

Stigma surrounding mental illness and mental health treatment remains a significant problem, particularly among African Americans. This study sought to examine the effects of 2 intervention delivery methods in reducing reported stigma. African Americans (n = 158) were nonrandomly assigned to an in-person contact or video condition and administered a survey immediately before, after, and 2 weeks following the stigma intervention. The in vivo contact condition consisted of an African American man discussing his experiences with mental illness and psychotherapy. The session was recorded, and the recording was used for the video condition. There were no significant effects based on delivery method; however, there was a significant effect for time on stigma and help-seeking attitude measures. Further research is needed to determine the overall effectiveness of the intervention.

Postprocessing for Air Quality Predictions

NASA Astrophysics Data System (ADS)

Delle Monache, L.

2017-12-01

In recent year, air quality (AQ) forecasting has made significant progress towards better predictions with the goal of protecting the public from harmful pollutants. This progress is the results of improvements in weather and chemical transport models, their coupling, and more accurate emission inventories (e.g., with the development of new algorithms to account in near real-time for fires). Nevertheless, AQ predictions are still affected at times by significant biases which stem from limitations in both weather and chemistry transport models. Those are the result of numerical approximations and the poor representation (and understanding) of important physical and chemical process. Moreover, although the quality of emission inventories has been significantly improved, they are still one of the main sources of uncertainties in AQ predictions. For operational real-time AQ forecasting, a significant portion of these biases can be reduced with the implementation of postprocessing methods. We will review some of the techniques that have been proposed to reduce both systematic and random errors of AQ predictions, and improve the correlation between predictions and observations of ground-level ozone and surface particulate matter less than 2.5 µm in diameter (PM2.5). These methods, which can be applied to both deterministic and probabilistic predictions, include simple bias-correction techniques, corrections inspired by the Kalman filter, regression methods, and the more recently developed analog-based algorithms. These approaches will be compared and contrasted, and strength and weaknesses of each will be discussed.

Reduced detection by Ziehl-Neelsen method of acid-fast bacilli in sputum samples preserved in cetylpyridinium chloride solution.

PubMed

Selvakumar, N; Sudhamathi, S; Duraipandian, M; Frieden, T R; Narayanan, P R

2004-02-01

Twelve health facilities implementing the DOTS strategy, and the Tuberculosis Research Centre (TRC), Chennai, India. To determine the detection rates using Ziehl-Neelsen (ZN) and auramine-phenol to stain acid-fast bacilli (AFB) in sputum samples stored in cetylpyridinium chloride (CPC) solution. Two smears were prepared from each of 988 sputum samples collected in CPC and randomly allocated, one to ZN and the other to auramine-phenol staining. All samples were processed for culture of Mycobacterium tuberculosis. A significantly higher proportion of samples were negative using the ZN method compared to the auramine-phenol method (74.5% vs. 61.8%, McNamara's paired chi2 test; P < 0.001). Among 377 samples that were positive using auramine-phenol, 44% were negative using ZN. There were more culture-positive, smear-negative samples in ZN (52.7%) than in auramine-phenol (30%); the difference attained statistical significance (McNemar's paired chi2 test; P < 0.00004). Using ZN, of the 104 smears made immediately after collection, 52 were positive for AFB, of which only 35 (67.3%) were positive after storage in CPC; the reduction in the number of positive smears attained statistical significance (McNemar's paired chi2 test; P = 0.004). Detection of AFB in sputum samples preserved in CPC is significantly reduced using ZN staining.

A Web-Based Program to Increase Knowledge and Reduce Cigarette and Nargila Smoking Among Arab University Students in Israel: Mixed-Methods Study to Test Acceptability

PubMed Central

Linn, Shai; Rafaeli, Sheizaf

2015-01-01

Background Among Arab citizens in Israel, cigarette and nargila (hookah, waterpipe) smoking is a serious public health problem, particularly among the young adult population. With the dramatic increase of Internet and computer use among Arab college and university students, a Web-based program may provide an easy, accessible tool to reduce smoking rates without heavy resource demands required by traditional methods. Objective The purpose of this research was to examine the acceptability and feasibility of a pilot Web-based program that provides tailored feedback to increase smoking knowledge and reduce cigarette and nargila smoking behaviors among Arab college/university students in Israel. Methods A pilot Web-based program was developed, consisting of a self-administered questionnaire and feedback system on cigarette and nargila smoking. Arab university students were recruited to participate in a mixed-methods study, using both quantitative (pre-/posttest study design) and qualitative tools. A posttest was implemented at 1 month following participation in the intervention to assess any changes in smoking knowledge and behaviors. Focus group sessions were implemented to assess acceptability and preferences related to the Web-based program. Results A total of 225 participants—response rate of 63.2% (225/356)—completed the intervention at baseline and at 1-month poststudy, and were used for the comparative analysis. Statistically significant reductions in nargila smoking among participants (P=.001) were found. The intervention did not result in reductions in cigarette smoking. However, the tailored Web intervention resulted in statistically significant increases in the intention to quit smoking (P=.021). No statistically significant increases in knowledge were seen at 1-month poststudy. Participants expressed high satisfaction with the intervention and 93.8% (211/225) of those who completed the intervention at both time intervals reported that they would recommend the program to their friends, indicating excellent acceptability and feasibility of the intervention. This was further emphasized in the focus group sessions. Conclusions A tailored Web-based program may be a promising tool to reduce nargila smoking among Arab university students in Israel. The tailored Web intervention was not successful at significantly reducing cigarette smoking or increasing knowledge. However, the intervention did increase participants’ intention to quit smoking. Participants considered the Web-based tool to be an interesting, feasible, and highly acceptable strategy. Trial Registration Trial Registration: ISRCTN registry ISRCTN59207794; http://www.isrctn.com/ISRCTN59207794 (Archived by WebCite at http://www.webcitation.org/6VkYOBNOJ). PMID:25707034

Domestic cooking methods affect the nutritional quality of red cabbage.

PubMed

Xu, Feng; Zheng, Yonghua; Yang, Zhenfeng; Cao, Shifeng; Shao, Xingfeng; Wang, Hongfei

2014-10-15

The aim of this work is to investigate the effects of domestic cooking methods, including steaming, microwave heating, boiling and stir-frying on the nutritional quality of red cabbage. Compared with fresh-cut red cabbage, all cooking methods were found to cause significant reduction in anthocyanin and total glucosinolates contents. Moreover, steaming resulted in significantly greater retention of vitamin C and DPPH radical-scavenging activity, while stir-frying and boiling, two popular Chinese cooking methods, led to significant losses of total phenolic, vitamin C, DPPH radical-scavenging activity, and total soluble sugar as well as reducing sugars. Normally, red cabbage consumed fresh in salads could maintain the highest nutrition. However, considering the habits of Asian cuisine, it is recommended to use less water and less cooking time, such as steaming based on our present results, so as to retain the optimum benefits of the health-promoting compounds. Copyright © 2014 Elsevier Ltd. All rights reserved.

Investigation of membranous ventricular septal defect complicated with tricuspid regurgitation in ventricular septal defect occlusion

PubMed Central

LIU, SHU-PING; LI, LI; YAO, KE-CHUN; WANG, NA; WANG, JIAN-CHANG

2013-01-01

This study aimed to explore the mechanism of membranous ventricular septal defect complicated with tricuspid regurgitation and the significance of ventricular septal defect occlusion by echocardiography. A total of 43 patients with membranous ventricular septal defect complicated with tricuspid regurgitation were observed by echocardiography and the changes in length, area and volume of tricuspid regurgitation prior to and following ventricular septal defect occlusion were measured. There were four different mechanisms of membranous ventricular septal defect complicated with tricuspid regurgitation. The various indices of tricuspid regurgitation volume were significantly reduced following occlusion. Ventricular septal defect occlusion significantly reduces tricuspid regurgitation volume complicated with membranous ventricular septal defect and echocardiography is an ideal method to detect these changes. PMID:23404058

Boiling and frying peanuts decreases soluble peanut (Arachis Hypogaea) allergens Ara h 1 and Ara h 2 but does not generate hypoallergenic peanuts

USDA-ARS?s Scientific Manuscript database

Peanut allergy continues to be a problem in most developed countries of the world. We sought a processing method that would alter allergenic peanut proteins, such that allergen recognition by IgE from allergic individuals would be significantly reduced or eliminated. Such a method would render accid...

Inhibition of cell surface expression of endothelial adhesion molecules by ursolic acid prevents intimal hyperplasia of venous bypass grafts in rats

PubMed Central

Zeller, Iris; Wiedemann, Dominik; Schwaiger, Stefan; Stelzmüller, Marlies; Kreutmayer, Simone; Leberfing, Oliver; Stuppner, Hermann; Bernhard, David

2012-01-01

OBJECTIVES Despite rapid progress in surgical techniques, there is still a significant lack of surgery-supportive pharmacological treatments. The aim of this study was to test the hypothesis that ursolic acid (UA) may prevent intimal hyperplasia of venous bypass grafts. METHODS The hypothesis was tested by means of primary cell isolation and culture followed by real-time polymerase chain reaction, western blotting, fluorescence microscopy and fluorescence-activated cell sorting analyses, as well as an in vivo rat model for intimal hyperplasia of venous bypass grafts and immunohistochemistry and histochemistry. RESULTS The local application of UA significantly inhibited intimal hyperplasia in vivo (intimal thickness control: 25 μm, UA group: 18 μM–8 weeks after surgery). The UA treatment of grafts significantly resulted in reduced endothelial vascular cell adhesion molecule-1 (VCAM-1) expression, reduced infiltration of the grafts vessel wall by CD45-positive cells and increased smooth muscle cell (SMC) death. In in vitro condition, it could be shown that UA inhibits VCAM-1 expression downstream of NFκB and is likely to interfere with VCAM-1 protein synthesis in endothelial cells. Quantification of cell death in vascular smooth muscle cells treated with UA indicated that UA is a potent inducer of SMC apoptosis. CONCLUSIONS Our results suggest that UA-mediated inhibition of endothelial VCAM-1 expression reduces the infiltration of venous bypass grafts by CD45-positive cells and inhibits intimal hyperplasia. Apoptosis induction in SMCs may be another method in which UA reduces intimal thickening. UA may constitute a surgery-supportive pharmacon that reduces intimal hyperplasia of vein grafts. PMID:22551965

Density-cluster NMA: A new protein decomposition technique for coarse-grained normal mode analysis.

PubMed

Demerdash, Omar N A; Mitchell, Julie C

2012-07-01

Normal mode analysis has emerged as a useful technique for investigating protein motions on long time scales. This is largely due to the advent of coarse-graining techniques, particularly Hooke's Law-based potentials and the rotational-translational blocking (RTB) method for reducing the size of the force-constant matrix, the Hessian. Here we present a new method for domain decomposition for use in RTB that is based on hierarchical clustering of atomic density gradients, which we call Density-Cluster RTB (DCRTB). The method reduces the number of degrees of freedom by 85-90% compared with the standard blocking approaches. We compared the normal modes from DCRTB against standard RTB using 1-4 residues in sequence in a single block, with good agreement between the two methods. We also show that Density-Cluster RTB and standard RTB perform well in capturing the experimentally determined direction of conformational change. Significantly, we report superior correlation of DCRTB with B-factors compared with 1-4 residue per block RTB. Finally, we show significant reduction in computational cost for Density-Cluster RTB that is nearly 100-fold for many examples. Copyright © 2012 Wiley Periodicals, Inc.

Short-term postnatal quality of life in women with previous Misgav Ladach caesarean section compared to Pfannenstiel-Dorffler caesarean section method.

PubMed

Fatušić, Zlatan; Hudić, Igor; Sinanović, Osman; Kapidžić, Mirela; Hotić, Nešad; Musić, Asim

2011-09-01

To examine whether short-term postnatal health-related quality of life differed among women after different methods of cesarean sections. One hundred forty-five women were evaluated with previous CS (85 by Misgav Ladach and 60 by Pfannenstiel-Dörffler). Short-time quality of life was measured using the Croatian version of Short Form Health Survey (SF - 36). Short-term postoperative recovery was assessed using two criteria: febrile morbidity and degree of pain. Incidence of peritoneal adhesions was assigned using Bristow scoring system. Four weeks after delivery women with previous Misgav Ladach cesarean section significantly scored higher on the bodily pain (72.4 vs. 56.7, p < 0.05), social functioning (71.5 vs. 60.4, p < 0.05), and the vitality (61.7 vs. 50.3, p < 0.05) subscales. These differences disappeared in the second assessment (12-weeks postpartum) except in the bodily pain (74.7 vs. 61.2, p < 0.05) subscale. There was a significant trend toward a higher requirement for postoperative analgesics in the Pfannenstiel-Dörfler group (doses: 5.4 vs. 8.7, p < 0.05; hours: 17.9 vs. 23.3, p < 0.05), and they had a significantly higher rate of febrile morbidity than the Misgav Ladach group (5.7 vs. 9.4%, p < 0.05). Hospitalization time was reduced in the Misgav Ladach group (4.2 vs. 7.3, p <\\ 0.05). The incidence of adhesions was significantly lower in patients who had undergone a previous operation using the original Misgav Ladach method (0.47 vs. 0.77, p < 0.05). Misgav Ladach cesarean section method might lead to better short-time quality of life resulting in reducing postoperative complications compared to Pfannenstiel-Dörfler cesarean section method.

Effect of Exogenous Phytase Addition on Soil Phosphatase Activities: a Fluorescence Spectroscopy Study.

PubMed

Yang, Xiao-zhu; Chen, Zhen-hua; Zhang, Yu-lan; Chen, Li-jun

2015-05-01

The utilization of organic phosphorus (P) has directly or indirectly improved after exogenous phytase was added to soil. However, the mechanism by which exogenous phytase affected the soil phosphatases (phosphomonoesterase and phosphodiesterase) activities was not clear. The present work was aimed to study red soil, brown soil and cinnamon soil phosphomonoesterase (acid and alkaline) (AcP and AlP) and phosphodiesterase (PD) activities responding to the addition of exogenous phytase (1 g phytase/50 g air dry soil sample) based on the measurements performed via a fluorescence detection method combined with 96 microplates using a TECAN Infinite 200 Multi-Mode Microplate Reader. The results indicated that the acid phosphomonoesterase activity was significantly enhanced in red soil (p≤0. 01), while it was significantly reduced in cinnamon soil; alkaline phosphomonoesterase activity was significantly enhanced in cinnamon soil (p≤ 0. 01), while it was significantly reduced in red soil; phosphodiesterase activity was increased in three soils but it was significantly increased in brown soil (p≤0. 01) after the addition of exogenous phytase. The activities still remained strong after eight days in different soils, which indicated that exogenous phytase addition could be enhance soil phosphatases activities effectively. This effect was not only related to soil properties, such as pH and phosphorus forms, but might also be related to the excreted enzyme amount of the stimulating microorganism. Using fluorescence spectroscopy to study exogenous phytase addition influence on soil phosphatase activities was the first time at home and abroad. Compared with the conventional spectrophotometric method, the fluorescence microplate method is an accurate, fast and simple to use method to determine the relationships among the soil phosphatases activities.

Integrating Formal Methods and Testing 2002

NASA Technical Reports Server (NTRS)

Cukic, Bojan

2002-01-01

Traditionally, qualitative program verification methodologies and program testing are studied in separate research communities. None of them alone is powerful and practical enough to provide sufficient confidence in ultra-high reliability assessment when used exclusively. Significant advances can be made by accounting not only tho formal verification and program testing. but also the impact of many other standard V&V techniques, in a unified software reliability assessment framework. The first year of this research resulted in the statistical framework that, given the assumptions on the success of the qualitative V&V and QA procedures, significantly reduces the amount of testing needed to confidently assess reliability at so-called high and ultra-high levels (10-4 or higher). The coming years shall address the methodologies to realistically estimate the impacts of various V&V techniques to system reliability and include the impact of operational risk to reliability assessment. Combine formal correctness verification, process and product metrics, and other standard qualitative software assurance methods with statistical testing with the aim of gaining higher confidence in software reliability assessment for high-assurance applications. B) Quantify the impact of these methods on software reliability. C) Demonstrate that accounting for the effectiveness of these methods reduces the number of tests needed to attain certain confidence level. D) Quantify and justify the reliability estimate for systems developed using various methods.

Random access with adaptive packet aggregation in LTE/LTE-A.

PubMed

Zhou, Kaijie; Nikaein, Navid

While random access presents a promising solution for efficient uplink channel access, the preamble collision rate can significantly increase when massive number of devices simultaneously access the channel. To address this issue and improve the reliability of the random access, an adaptive packet aggregation method is proposed. With the proposed method, a device does not trigger a random access for every single packet. Instead, it starts a random access when the number of aggregated packets reaches a given threshold. This method reduces the packet collision rate at the expense of an extra latency, which is used to accumulate multiple packets into a single transmission unit. Therefore, the tradeoff between packet loss rate and channel access latency has to be carefully selected. We use semi-Markov model to derive the packet loss rate and channel access latency as functions of packet aggregation number. Hence, the optimal amount of aggregated packets can be found, which keeps the loss rate below the desired value while minimizing the access latency. We also apply for the idea of packet aggregation for power saving, where a device aggregates as many packets as possible until the latency constraint is reached. Simulations are carried out to evaluate our methods. We find that the packet loss rate and/or power consumption are significantly reduced with the proposed method.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoon, Boram; Gupta, Rajan; Bhattacharya, Tanmoy

We present a detailed analysis of methods to reduce statistical errors and excited-state contamination in the calculation of matrix elements of quark bilinear operators in nucleon states. All the calculations were done on a 2+1 flavor ensemble with lattices of sizemore » $$32^3 \\times 64$$ generated using the rational hybrid Monte Carlo algorithm at $a=0.081$~fm and with $$M_\\pi=312$$~MeV. The statistical precision of the data is improved using the all-mode-averaging method. We compare two methods for reducing excited-state contamination: a variational analysis and a two-state fit to data at multiple values of the source-sink separation $$t_{\\rm sep}$$. We show that both methods can be tuned to significantly reduce excited-state contamination and discuss their relative advantages and cost-effectiveness. A detailed analysis of the size of source smearing used in the calculation of quark propagators and the range of values of $$t_{\\rm sep}$$ needed to demonstrate convergence of the isovector charges of the nucleon to the $$t_{\\rm sep} \\to \\infty $$ estimates is presented.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoon, Boram; Gupta, Rajan; Bhattacharya, Tanmoy

We present a detailed analysis of methods to reduce statistical errors and excited-state contamination in the calculation of matrix elements of quark bilinear operators in nucleon states. All the calculations were done on a 2+1-flavor ensemble with lattices of size 32 3 × 64 generated using the rational hybrid Monte Carlo algorithm at a = 0.081 fm and with M π = 312 MeV. The statistical precision of the data is improved using the all-mode-averaging method. We compare two methods for reducing excited-state contamination: a variational analysis and a 2-state fit to data at multiple values of the source-sink separationmore » t sep. We show that both methods can be tuned to significantly reduce excited-state contamination and discuss their relative advantages and cost effectiveness. As a result, a detailed analysis of the size of source smearing used in the calculation of quark propagators and the range of values of t sep needed to demonstrate convergence of the isovector charges of the nucleon to the t sep → ∞ estimates is presented.« less

Controlling excited-state contamination in nucleon matrix elements

DOE PAGES

Yoon, Boram; Gupta, Rajan; Bhattacharya, Tanmoy; ...

2016-06-08

We present a detailed analysis of methods to reduce statistical errors and excited-state contamination in the calculation of matrix elements of quark bilinear operators in nucleon states. All the calculations were done on a 2+1-flavor ensemble with lattices of size 32 3 × 64 generated using the rational hybrid Monte Carlo algorithm at a = 0.081 fm and with M π = 312 MeV. The statistical precision of the data is improved using the all-mode-averaging method. We compare two methods for reducing excited-state contamination: a variational analysis and a 2-state fit to data at multiple values of the source-sink separationmore » t sep. We show that both methods can be tuned to significantly reduce excited-state contamination and discuss their relative advantages and cost effectiveness. As a result, a detailed analysis of the size of source smearing used in the calculation of quark propagators and the range of values of t sep needed to demonstrate convergence of the isovector charges of the nucleon to the t sep → ∞ estimates is presented.« less

Evaluating the Effect of Processing Parameters on Porosity in Electron Beam Melted Ti-6Al-4V via Synchrotron X-ray Microtomography

NASA Astrophysics Data System (ADS)

Cunningham, Ross; Narra, Sneha P.; Ozturk, Tugce; Beuth, Jack; Rollett, A. D.

2016-03-01

Electron beam melting (EBM) is one of the subsets of direct metal additive manufacturing (AM), an emerging manufacturing method that fabricates metallic parts directly from a three-dimensional (3D) computer model by the successive melting of powder layers. This family of technologies has seen significant growth in recent years due to its potential to manufacture complex components with shorter lead times, reduced material waste and minimal post-processing as a "near-net-shape" process, making it of particular interest to the biomedical and aerospace industries. The popular titanium alloy Ti-6Al-4V has been the focus of multiple studies due to its importance to these two industries, which can be attributed to its high strength to weight ratio and corrosion resistance. While previous research has found that most tensile properties of EBM Ti-6Al-4V meet or exceed conventional manufacturing standards, fatigue properties have been consistently inferior due to a significant presence of porosity. Studies have shown that adjusting processing parameters can reduce overall porosity; however, they frequently utilize methods that give insufficient information to properly characterize the porosity (e.g., Archimedes' method). A more detailed examination of the result of process parameter adjustments on the size and spatial distribution of gas porosity was performed utilizing synchrotron-based x-ray microtomography with a minimum feature resolution of 1.5 µm. Cross-sectional melt pool area was varied systematically via process mapping. Increasing melt pool area through the speed function variable was observed to significantly reduce porosity in the part.

Pulse transmission receiver with higher-order time derivative pulse generator

DOEpatents

Dress, Jr., William B.; Smith, Stephen F.

2003-08-12

Systems and methods for pulse-transmission low-power communication modes are disclosed. A pulse transmission receiver includes: a front-end amplification/processing circuit; a synchronization circuit coupled to the front-end amplification/processing circuit; a clock coupled to the synchronization circuit; a trigger signal generator coupled to the clock; and at least one higher-order time derivative pulse generator coupled to the trigger signal generator. The systems and methods significantly reduce lower-frequency emissions from pulse transmission spread-spectrum communication modes, which reduces potentially harmful interference to existing radio frequency services and users and also simultaneously permit transmission of multiple data bits by utilizing specific pulse shapes.

Comet brightness parameters: Definition, determination, and correlations

NASA Technical Reports Server (NTRS)

Meisel, D. D.; Morris, C. S.

1976-01-01

The power-law definition of comet brightness is reviewed and possible systematic influences are discussed that can affect the derivation of m sub o and n values from visual magnitude estimates. A rationale for the Bobrovnikoff aperture correction method is given and it is demonstrated that the Beyer extrafocal method leads to large systematic effects which if uncorrected by an instrumental relationship result in values significantly higher than those derived according to the Bobrovnikoff guidelines. A series of visual brightness parameter sets are presented which have been reduced to the same photometric system. Recommendations are given to insure that future observations are reduced to the same system.

Computationally efficient method for Fourier transform of highly chirped pulses for laser and parametric amplifier modeling.

PubMed

Andrianov, Alexey; Szabo, Aron; Sergeev, Alexander; Kim, Arkady; Chvykov, Vladimir; Kalashnikov, Mikhail

2016-11-14

We developed an improved approach to calculate the Fourier transform of signals with arbitrary large quadratic phase which can be efficiently implemented in numerical simulations utilizing Fast Fourier transform. The proposed algorithm significantly reduces the computational cost of Fourier transform of a highly chirped and stretched pulse by splitting it into two separate transforms of almost transform limited pulses, thereby reducing the required grid size roughly by a factor of the pulse stretching. The application of our improved Fourier transform algorithm in the split-step method for numerical modeling of CPA and OPCPA shows excellent agreement with standard algorithms.

Pulse transmission receiver with higher-order time derivative pulse correlator

DOEpatents

Dress, Jr., William B.; Smith, Stephen F.

2003-09-16

Systems and methods for pulse-transmission low-power communication modes are disclosed. A pulse transmission receiver includes: a higher-order time derivative pulse correlator; a demodulation decoder coupled to the higher-order time derivative pulse correlator; a clock coupled to the demodulation decoder; and a pseudorandom polynomial generator coupled to both the higher-order time derivative pulse correlator and the clock. The systems and methods significantly reduce lower-frequency emissions from pulse transmission spread-spectrum communication modes, which reduces potentially harmful interference to existing radio frequency services and users and also simultaneously permit transmission of multiple data bits by utilizing specific pulse shapes.

Antioxidant, analgesic and anti-inflammatory activities of the methanolic extract of Piper betle leaves.

PubMed

Alam, Badrul; Akter, Fahima; Parvin, Nahida; Sharmin Pia, Rashna; Akter, Sharmin; Chowdhury, Jesmin; Sifath-E-Jahan, Kazi; Haque, Ekramul

2013-01-01

The present study was designed to evaluate the antioxidant, analgesic, and anti-inflammatory activities of the methanolic extract of Piper betle leaves (MPBL). MPBL was evaluated for anti-inflammatory activity using carrageenan-induced hind paw edema model. Analgesic activity of MPBL was evaluated by hot plate, writhing, and formalin tests. Total phenolic and flavonoids content, total antioxidant activity, scavenging of 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical, peroxynitrate (ONOO) as well as inhibition of total ROS generation, and assessment of reducing power were used to evaluate antioxidant potential of MPBL. The extract of MPBL, at the dose of 100 and 200 mg/kg, produced a significant (p<0.05) increase in pain threshold in hot plate method whereas significantly (p<0.05) reduced the writhing caused by acetic acid and the number of licks induced by formalin in a dose-dependent manner. The same ranges of doses of MPBL caused significant (p<0.05) inhibition of carrageenan-induced paw edema after 4 h in a dose-dependent manner. In DPPH, ONOO(-), and total ROS scavenging method, MPBL showed good antioxidant potentiality with the IC50 value of 16.33±1.02, 25.16±0.61 , and 41.72±0.48 µg/ml, respectively with a significant (p<0.05) good reducing power. The findings of the study suggested that MPBL has strong analgesic, anti-inflammatory, and antioxidant effects, conforming the traditional use of this plant for inflammatory pain alleviation to its antioxidant potentiality.

Reducing intraoperative red blood cell unit wastage in a large academic medical center

PubMed Central

Whitney, Gina M.; Woods, Marcella C.; France, Daniel J.; Austin, Thomas M.; Deegan, Robert J.; Paroskie, Allison; Booth, Garrett S.; Young, Pampee P.; Dmochowski, Roger R.; Sandberg, Warren S.; Pilla, Michael A.

2015-01-01

BACKGROUND The wastage of red blood cell (RBC) units within the operative setting results in significant direct costs to health care organizations. Previous education-based efforts to reduce wastage were unsuccessful at our institution. We hypothesized that a quality and process improvement approach would result in sustained reductions in intraoperative RBC wastage in a large academic medical center. STUDY DESIGN AND METHODS Utilizing a failure mode and effects analysis supplemented with time and temperature data, key drivers of perioperative RBC wastage were identified and targeted for process improvement. RESULTS Multiple contributing factors, including improper storage and transport and lack of accurate, locally relevant RBC wastage event data were identified as significant contributors to ongoing intraoperative RBC unit wastage. Testing and implementation of improvements to the process of transport and storage of RBC units occurred in liver transplant and adult cardiac surgical areas due to their history of disproportionately high RBC wastage rates. Process interventions targeting local drivers of RBC wastage resulted in a significant reduction in RBC wastage (p <0.0001; adjusted odds ratio, 0.24; 95% confidence interval, 0.15–0.39), despite an increase in operative case volume over the period of the study. Studied process interventions were then introduced incrementally in the remainder of the perioperative areas. CONCLUSIONS These results show that a multidisciplinary team focused on the process of blood product ordering, transport, and storage was able to significantly reduce operative RBC wastage and its associated costs using quality and process improvement methods. PMID:26202213

Energy Management in Smart Cities Based on Internet of Things: Peak Demand Reduction and Energy Savings.

PubMed

Mahapatra, Chinmaya; Moharana, Akshaya Kumar; Leung, Victor C M

2017-12-05

Around the globe, innovation with integrating information and communication technologies (ICT) with physical infrastructure is a top priority for governments in pursuing smart, green living to improve energy efficiency, protect the environment, improve the quality of life, and bolster economy competitiveness. Cities today faces multifarious challenges, among which energy efficiency of homes and residential dwellings is a key requirement. Achieving it successfully with the help of intelligent sensors and contextual systems would help build smart cities of the future. In a Smart home environment Home Energy Management plays a critical role in finding a suitable and reliable solution to curtail the peak demand and achieve energy conservation. In this paper, a new method named as Home Energy Management as a Service (HEMaaS) is proposed which is based on neural network based Q -learning algorithm. Although several attempts have been made in the past to address similar problems, the models developed do not cater to maximize the user convenience and robustness of the system. In this paper, authors have proposed an advanced Neural Fitted Q -learning method which is self-learning and adaptive. The proposed method provides an agile, flexible and energy efficient decision making system for home energy management. A typical Canadian residential dwelling model has been used in this paper to test the proposed method. Based on analysis, it was found that the proposed method offers a fast and viable solution to reduce the demand and conserve energy during peak period. It also helps reducing the carbon footprint of residential dwellings. Once adopted, city blocks with significant residential dwellings can significantly reduce the total energy consumption by reducing or shifting their energy demand during peak period. This would definitely help local power distribution companies to optimize their resources and keep the tariff low due to curtailment of peak demand.

Energy Management in Smart Cities Based on Internet of Things: Peak Demand Reduction and Energy Savings

PubMed Central

Moharana, Akshaya Kumar

2017-01-01

Around the globe, innovation with integrating information and communication technologies (ICT) with physical infrastructure is a top priority for governments in pursuing smart, green living to improve energy efficiency, protect the environment, improve the quality of life, and bolster economy competitiveness. Cities today faces multifarious challenges, among which energy efficiency of homes and residential dwellings is a key requirement. Achieving it successfully with the help of intelligent sensors and contextual systems would help build smart cities of the future. In a Smart home environment Home Energy Management plays a critical role in finding a suitable and reliable solution to curtail the peak demand and achieve energy conservation. In this paper, a new method named as Home Energy Management as a Service (HEMaaS) is proposed which is based on neural network based Q-learning algorithm. Although several attempts have been made in the past to address similar problems, the models developed do not cater to maximize the user convenience and robustness of the system. In this paper, authors have proposed an advanced Neural Fitted Q-learning method which is self-learning and adaptive. The proposed method provides an agile, flexible and energy efficient decision making system for home energy management. A typical Canadian residential dwelling model has been used in this paper to test the proposed method. Based on analysis, it was found that the proposed method offers a fast and viable solution to reduce the demand and conserve energy during peak period. It also helps reducing the carbon footprint of residential dwellings. Once adopted, city blocks with significant residential dwellings can significantly reduce the total energy consumption by reducing or shifting their energy demand during peak period. This would definitely help local power distribution companies to optimize their resources and keep the tariff low due to curtailment of peak demand. PMID:29206159

Model's sparse representation based on reduced mixed GMsFE basis methods

NASA Astrophysics Data System (ADS)

Jiang, Lijian; Li, Qiuqi

2017-06-01

In this paper, we propose a model's sparse representation based on reduced mixed generalized multiscale finite element (GMsFE) basis methods for elliptic PDEs with random inputs. A typical application for the elliptic PDEs is the flow in heterogeneous random porous media. Mixed generalized multiscale finite element method (GMsFEM) is one of the accurate and efficient approaches to solve the flow problem in a coarse grid and obtain the velocity with local mass conservation. When the inputs of the PDEs are parameterized by the random variables, the GMsFE basis functions usually depend on the random parameters. This leads to a large number degree of freedoms for the mixed GMsFEM and substantially impacts on the computation efficiency. In order to overcome the difficulty, we develop reduced mixed GMsFE basis methods such that the multiscale basis functions are independent of the random parameters and span a low-dimensional space. To this end, a greedy algorithm is used to find a set of optimal samples from a training set scattered in the parameter space. Reduced mixed GMsFE basis functions are constructed based on the optimal samples using two optimal sampling strategies: basis-oriented cross-validation and proper orthogonal decomposition. Although the dimension of the space spanned by the reduced mixed GMsFE basis functions is much smaller than the dimension of the original full order model, the online computation still depends on the number of coarse degree of freedoms. To significantly improve the online computation, we integrate the reduced mixed GMsFE basis methods with sparse tensor approximation and obtain a sparse representation for the model's outputs. The sparse representation is very efficient for evaluating the model's outputs for many instances of parameters. To illustrate the efficacy of the proposed methods, we present a few numerical examples for elliptic PDEs with multiscale and random inputs. In particular, a two-phase flow model in random porous media is simulated by the proposed sparse representation method.

Model's sparse representation based on reduced mixed GMsFE basis methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Lijian, E-mail: ljjiang@hnu.edu.cn; Li, Qiuqi, E-mail: qiuqili@hnu.edu.cn

2017-06-01

In this paper, we propose a model's sparse representation based on reduced mixed generalized multiscale finite element (GMsFE) basis methods for elliptic PDEs with random inputs. A typical application for the elliptic PDEs is the flow in heterogeneous random porous media. Mixed generalized multiscale finite element method (GMsFEM) is one of the accurate and efficient approaches to solve the flow problem in a coarse grid and obtain the velocity with local mass conservation. When the inputs of the PDEs are parameterized by the random variables, the GMsFE basis functions usually depend on the random parameters. This leads to a largemore » number degree of freedoms for the mixed GMsFEM and substantially impacts on the computation efficiency. In order to overcome the difficulty, we develop reduced mixed GMsFE basis methods such that the multiscale basis functions are independent of the random parameters and span a low-dimensional space. To this end, a greedy algorithm is used to find a set of optimal samples from a training set scattered in the parameter space. Reduced mixed GMsFE basis functions are constructed based on the optimal samples using two optimal sampling strategies: basis-oriented cross-validation and proper orthogonal decomposition. Although the dimension of the space spanned by the reduced mixed GMsFE basis functions is much smaller than the dimension of the original full order model, the online computation still depends on the number of coarse degree of freedoms. To significantly improve the online computation, we integrate the reduced mixed GMsFE basis methods with sparse tensor approximation and obtain a sparse representation for the model's outputs. The sparse representation is very efficient for evaluating the model's outputs for many instances of parameters. To illustrate the efficacy of the proposed methods, we present a few numerical examples for elliptic PDEs with multiscale and random inputs. In particular, a two-phase flow model in random porous media is simulated by the proposed sparse representation method.« less

RECOVERY OF VOCS FROM SURFACTANT SOLUTION BY PERVAPORATION

EPA Science Inventory

Surfactant-based processes are emerging as promising technologies to enhance conventional pump-and-treat methods for remediating soils contaminated with nonaqueous phase liquids (NAPLs), primarily due to the potential to significantly reduce the remediation time. In order to reus...

Developing Alternative Methods/Techniques for Plant Establishment Under Reduced Irrigation

DOT National Transportation Integrated Search

2009-06-10

The purpose of the study was to evaluate soil treatments for their effect on establishment of wild-land : shrubs without supplemental irrigation. The treatments that significantly improved growth over irrigation : alone at a central California fill s...

Gun-Control Legislation and the Impact on Suicide.

PubMed

Leenaars, Antoon A

2007-01-01

Gun control is the prototypical example of controlling the environment for the means of suicide, an effective public health approach to suicide prevention. Canada's Criminal Law Amendment Act of 1977 (Bill C-51) provides an excellent opportunity to illustrate the effects of legislative gun-control laws and the impact on suicide. The research in Canada supports the significant effect of C-51 in reducing suicides and firearm suicides, even if one controls for socioeconomic factors, although not equally for all ages. The young, a high-risk group, show the most significant decrease, without significant substitution of other methods (displacement). Studies on gun-control laws from New Zealand, the United States, and Australia support the Canadian findings. It is concluded that, although not equally applicable in all countries, gun control may well have significant applications in reducing suicide worldwide.

Ice Accretion with Varying Surface Tension

NASA Technical Reports Server (NTRS)

Bilanin, Alan J.; Anderson, David N.

1995-01-01

During an icing encounter of an aircraft in flight, super-cooled water droplets impinging on an airfoil may splash before freezing. This paper reports tests performed to determine if this effect is significant and uses the results to develop an improved scaling method for use in icing test facilities. Simple laboratory tests showed that drops splash on impact at the Reynolds and Weber numbers typical of icing encounters. Further confirmation of droplet splash came from icing tests performed in the NaSA Lewis Icing Research Tunnel (IRT) with a surfactant added to the spray water to reduce the surface tension. The resulting ice shapes were significantly different from those formed when no surfactant was added to the water. These results suggested that the droplet Weber number must be kept constant to properly scale icing test conditions. Finally, the paper presents a Weber-number-based scaling method and reports results from scaling tests in the IRT in which model size was reduced up to a factor of 3. Scale and reference ice shapes are shown which confirm the effectiveness of this new scaling method.

Optimization of the Agar-gel Method for Isolation of Migrating Ascaris suum Larvae From the Liver and Lungs of Pigs

PubMed Central

Saeed, I; Roepstorff, A; Rasmussen, T; Høg, M; Jungersen, G

2001-01-01

Experiments on use of an agar-gel method for recovery of migrating Ascaris suum larvae from the liver and lungs of pigs were conducted to obtain fast standardized methods. Subsamples of blended tissues of pig liver and lungs were mixed with agar to a final concentration of 1% agar and the larvae allowed to migrate out of the agar-gel into 0.9% NaCl at 38°C. The results showed that within 3 h more than 88% of the recoverable larvae migrated out of the liver agar-gel and more than 83% of the obtained larvae migrated out of the lung agar-gel. The larvae were subsequently available in a very clean suspension which reduced the sample counting time. Blending the liver for 60 sec in a commercial blender showed significantly higher larvae recovery than blending for 30 sec. Addition of gentamycin to reduce bacterial growth during incubation, glucose to increase larval motility during migration or ice to increase sedimentation of migrated larvae did not influence larvae recovery significantly. PMID:11503373

Scatter correction for cone-beam computed tomography using self-adaptive scatter kernel superposition

NASA Astrophysics Data System (ADS)

Xie, Shi-Peng; Luo, Li-Min

2012-06-01

The authors propose a combined scatter reduction and correction method to improve image quality in cone beam computed tomography (CBCT). The scatter kernel superposition (SKS) method has been used occasionally in previous studies. However, this method differs in that a scatter detecting blocker (SDB) was used between the X-ray source and the tested object to model the self-adaptive scatter kernel. This study first evaluates the scatter kernel parameters using the SDB, and then isolates the scatter distribution based on the SKS. The quality of image can be improved by removing the scatter distribution. The results show that the method can effectively reduce the scatter artifacts, and increase the image quality. Our approach increases the image contrast and reduces the magnitude of cupping. The accuracy of the SKS technique can be significantly improved in our method by using a self-adaptive scatter kernel. This method is computationally efficient, easy to implement, and provides scatter correction using a single scan acquisition.

A Hyperspherical Adaptive Sparse-Grid Method for High-Dimensional Discontinuity Detection

DOE PAGES

Zhang, Guannan; Webster, Clayton G.; Gunzburger, Max D.; ...

2015-06-24

This study proposes and analyzes a hyperspherical adaptive hierarchical sparse-grid method for detecting jump discontinuities of functions in high-dimensional spaces. The method is motivated by the theoretical and computational inefficiencies of well-known adaptive sparse-grid methods for discontinuity detection. Our novel approach constructs a function representation of the discontinuity hypersurface of an N-dimensional discontinuous quantity of interest, by virtue of a hyperspherical transformation. Then, a sparse-grid approximation of the transformed function is built in the hyperspherical coordinate system, whose value at each point is estimated by solving a one-dimensional discontinuity detection problem. Due to the smoothness of the hypersurface, the newmore » technique can identify jump discontinuities with significantly reduced computational cost, compared to existing methods. In addition, hierarchical acceleration techniques are also incorporated to further reduce the overall complexity. Rigorous complexity analyses of the new method are provided as are several numerical examples that illustrate the effectiveness of the approach.« less

A hyper-spherical adaptive sparse-grid method for high-dimensional discontinuity detection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Guannan; Webster, Clayton G.; Gunzburger, Max D.

This work proposes and analyzes a hyper-spherical adaptive hierarchical sparse-grid method for detecting jump discontinuities of functions in high-dimensional spaces is proposed. The method is motivated by the theoretical and computational inefficiencies of well-known adaptive sparse-grid methods for discontinuity detection. Our novel approach constructs a function representation of the discontinuity hyper-surface of an N-dimensional dis- continuous quantity of interest, by virtue of a hyper-spherical transformation. Then, a sparse-grid approximation of the transformed function is built in the hyper-spherical coordinate system, whose value at each point is estimated by solving a one-dimensional discontinuity detection problem. Due to the smoothness of themore » hyper-surface, the new technique can identify jump discontinuities with significantly reduced computational cost, compared to existing methods. Moreover, hierarchical acceleration techniques are also incorporated to further reduce the overall complexity. Rigorous error estimates and complexity analyses of the new method are provided as are several numerical examples that illustrate the effectiveness of the approach.« less

A sample preparation method for recovering suppressed analyte ions in MALDI TOF MS.

PubMed

Lou, Xianwen; de Waal, Bas F M; Milroy, Lech-Gustav; van Dongen, Joost L J

2015-05-01

In matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI TOF MS), analyte signals can be substantially suppressed by other compounds in the sample. In this technical note, we describe a modified thin-layer sample preparation method that significantly reduces the analyte suppression effect (ASE). In our method, analytes are deposited on top of the surface of matrix preloaded on the MALDI plate. To prevent embedding of analyte into the matrix crystals, the sample solution were prepared without matrix and efforts were taken not to re-dissolve the preloaded matrix. The results with model mixtures of peptides, synthetic polymers and lipids show that detection of analyte ions, which were completely suppressed using the conventional dried-droplet method, could be effectively recovered by using our method. Our findings suggest that the incorporation of analytes in the matrix crystals has an important contributory effect on ASE. By reducing ASE, our method should be useful for the direct MALDI MS analysis of multicomponent mixtures. Copyright © 2015 John Wiley & Sons, Ltd.

Evaluating Composite Sampling Methods of Bacillus Spores at Low Concentrations

PubMed Central

Hess, Becky M.; Amidan, Brett G.; Anderson, Kevin K.; Hutchison, Janine R.

2016-01-01

Restoring all facility operations after the 2001 Amerithrax attacks took years to complete, highlighting the need to reduce remediation time. Some of the most time intensive tasks were environmental sampling and sample analyses. Composite sampling allows disparate samples to be combined, with only a single analysis needed, making it a promising method to reduce response times. We developed a statistical experimental design to test three different composite sampling methods: 1) single medium single pass composite (SM-SPC): a single cellulose sponge samples multiple coupons with a single pass across each coupon; 2) single medium multi-pass composite: a single cellulose sponge samples multiple coupons with multiple passes across each coupon (SM-MPC); and 3) multi-medium post-sample composite (MM-MPC): a single cellulose sponge samples a single surface, and then multiple sponges are combined during sample extraction. Five spore concentrations of Bacillus atrophaeus Nakamura spores were tested; concentrations ranged from 5 to 100 CFU/coupon (0.00775 to 0.155 CFU/cm2). Study variables included four clean surface materials (stainless steel, vinyl tile, ceramic tile, and painted dry wallboard) and three grime coated/dirty materials (stainless steel, vinyl tile, and ceramic tile). Analysis of variance for the clean study showed two significant factors: composite method (p< 0.0001) and coupon material (p = 0.0006). Recovery efficiency (RE) was higher overall using the MM-MPC method compared to the SM-SPC and SM-MPC methods. RE with the MM-MPC method for concentrations tested (10 to 100 CFU/coupon) was similar for ceramic tile, dry wall, and stainless steel for clean materials. RE was lowest for vinyl tile with both composite methods. Statistical tests for the dirty study showed RE was significantly higher for vinyl and stainless steel materials, but lower for ceramic tile. These results suggest post-sample compositing can be used to reduce sample analysis time when responding to a Bacillus anthracis contamination event of clean or dirty surfaces. PMID:27736999

Evaluating Composite Sampling Methods of Bacillus Spores at Low Concentrations.

PubMed

Hess, Becky M; Amidan, Brett G; Anderson, Kevin K; Hutchison, Janine R

2016-01-01

Restoring all facility operations after the 2001 Amerithrax attacks took years to complete, highlighting the need to reduce remediation time. Some of the most time intensive tasks were environmental sampling and sample analyses. Composite sampling allows disparate samples to be combined, with only a single analysis needed, making it a promising method to reduce response times. We developed a statistical experimental design to test three different composite sampling methods: 1) single medium single pass composite (SM-SPC): a single cellulose sponge samples multiple coupons with a single pass across each coupon; 2) single medium multi-pass composite: a single cellulose sponge samples multiple coupons with multiple passes across each coupon (SM-MPC); and 3) multi-medium post-sample composite (MM-MPC): a single cellulose sponge samples a single surface, and then multiple sponges are combined during sample extraction. Five spore concentrations of Bacillus atrophaeus Nakamura spores were tested; concentrations ranged from 5 to 100 CFU/coupon (0.00775 to 0.155 CFU/cm2). Study variables included four clean surface materials (stainless steel, vinyl tile, ceramic tile, and painted dry wallboard) and three grime coated/dirty materials (stainless steel, vinyl tile, and ceramic tile). Analysis of variance for the clean study showed two significant factors: composite method (p< 0.0001) and coupon material (p = 0.0006). Recovery efficiency (RE) was higher overall using the MM-MPC method compared to the SM-SPC and SM-MPC methods. RE with the MM-MPC method for concentrations tested (10 to 100 CFU/coupon) was similar for ceramic tile, dry wall, and stainless steel for clean materials. RE was lowest for vinyl tile with both composite methods. Statistical tests for the dirty study showed RE was significantly higher for vinyl and stainless steel materials, but lower for ceramic tile. These results suggest post-sample compositing can be used to reduce sample analysis time when responding to a Bacillus anthracis contamination event of clean or dirty surfaces.

Antioxidant and hepatoprotective activity of Cordia macleodii leaves

PubMed Central

Qureshi, Naseem N.; Kuchekar, Bhanudansh S.; Logade, Nadeem A.; Haleem, Majid A.

2009-01-01

This investigation was undertaken to evaluate ethanolic extract of Cordia macleodii leaves for possible antioxidant and hepatoprotective potential. Antioxidant activity of the extracts was evaluated by four established, in vitro methods viz. 1,1-diphenyl-2-picryl hydrazyl (DPPH) radical scavenging method, nitric oxide (NO) radical scavenging method, iron chelation method and reducing power method. The extract demonstrated a significant dose dependent antioxidant activity comparable with ascorbic acid. The extract was also evaluated for hepatoprotective activity by carbon tetrachloride (CCl4) induced liver damage model in rats. CCl4 produced a significant increase in levels of serum glutamate pyruvate transaminase (GPT), serum glutamate oxaloacetate transaminase (GOT), Alkaline Phosphatase (ALP) and total bilirubin. Pretreatment of the rats with ethanolic extract of C. macleodii (100, 200 and 400 mg/kg po) inhibited the increase in levels of GPT, GOT, ALP and total bilirubin and the inhibition was comparable with Silymarin (100 mg/kg po). The present study revealed that C. macleodii leaves have significant radical scavenging and hepatoprotective activities. PMID:23960714

Influence of photo- and thermal bleaching on pre-irradiation low water peak single mode fibers

NASA Astrophysics Data System (ADS)

Yin, Jianchong; Wen, Jianxiang; Luo, Wenyun; Xiao, Zhongyin; Chen, Zhenyi; Wang, Tingyun

2011-12-01

Reducing the radiation-induced transmission loss in low water peak single mode fiber (LWP SMF) has been investigated by using photo-bleaching method with 980nm pump light source and using thermal-bleaching method with temperature control system. The results show that the radiation-induced loss of pre-irradiation optical fiber can be reduced effectively with the help of photo-bleaching or thermal-bleaching. Although the effort of photo-bleaching is not as significant as thermal-bleaching, by using photo-bleaching method, the loss of fiber caused by radiation-induced defects can be reduced best up to 49% at 1310nm and 28% at 1550nm in low pre-irradiation condition, the coating of the fiber are not destroyed, and the rehabilitating time is just several hours, while self-annealing usually costs months' time. What's more, the typical high power LASER for photo-bleaching can be 980nm pump Laser Diode, which is very accessible.

Effects of aquaporin 4 and inward rectifier potassium channel 4.1 on medullospinal edema after methylprednisolone treatment to suppress acute spinal cord injury in rats.

PubMed

Li, Ye; Hu, Haifeng; Liu, Jingchen; Zhu, Qingsan; Gu, Rui

2018-02-01

To investigate the effects of aquaporin 4 (AQP4) and inward rectifier potassium channel 4.1 (Kir4.1) on medullospinal edema after treatment with methylprednisolone (MP) to suppress acute spinal cord injury (ASCI) in rats. Sprague Dawley rats were randomly divided into control, sham, ASCI, and MP-treated ASCI groups. After the induction of ASCI, we injected 30 mg/kg MP via the tail vein at various time points. The Tarlov scoring method was applied to evaluate neurological symptoms, and the wet-dry weights method was applied to measure the water content of the spinal cord. The motor function score of the ASCI group was significantly lower than that of the sham group, and the spinal water content was significantly increased. In addition, the levels of AQP4 and Kir4.1 were significantly increased, as was their degree of coexpression. Compared with that in the ASCI group, the motor function score and the water content were significantly increased in the MP group; in addition, the expression and coexpression of AQP4 and Kir4.1 were significantly reduced. Methylprednisolone inhibited medullospinal edema in rats with acute spinal cord injury, possibly by reducing the coexpression of aquaporin 4 and Kir4.1 in medullospinal tissues.

Archiving and Distributing Mouse Lines by Sperm Cryopreservation, IVF, and Embryo Transfer

PubMed Central

Takahashi, Hideko; Liu, Chengyu

2012-01-01

The number of genetically modified mouse lines has been increasing exponentially in the past few decades. In order to safeguard them from accidental loss and genetic drifting, to reduce animal housing cost, and to efficiently distribute them around the world, it is important to cryopreserve these valuable genetic resources. Preimplantation-stage embryos from thousands of mouse lines have been cryopreserved during the past two to three decades. Although reliable, this method requires several hundreds of embryos, which demands a sizable breeding colony, to safely preserve each line. This requirement imposes significant delay and financial burden for the archiving effort. Sperm cryopreservation is now emerging as the leading method for storing and distributing mouse lines, largely due to the recent finding that addition of a reducing agent, monothioglycerol, into the cryoprotectant can significantly increase the in vitro fertilization (IVF) rate in many mouse strains, including the most widely used C57BL/6 strain. This method is quick, inexpensive, and requires only two breeding age male mice, but it still remains tricky and strain-dependent. A small change in experimental conditions can lead to significant variations in the outcome. In this chapter, we describe in detail our sperm cryopreservation, IVF, and oviduct transfer procedures for storing and reviving genetically modified mouse lines. PMID:20691860

The use of methods of structural optimization at the stage of designing high-rise buildings with steel construction

NASA Astrophysics Data System (ADS)

Vasilkin, Andrey

2018-03-01

The more designing solutions at the search stage for design for high-rise buildings can be synthesized by the engineer, the more likely that the final adopted version will be the most efficient and economical. However, in modern market conditions, taking into account the complexity and responsibility of high-rise buildings the designer does not have the necessary time to develop, analyze and compare any significant number of options. To solve this problem, it is expedient to use the high potential of computer-aided designing. To implement automated search for design solutions, it is proposed to develop the computing facilities, the application of which will significantly increase the productivity of the designer and reduce the complexity of designing. Methods of structural and parametric optimization have been adopted as the basis of the computing facilities. Their efficiency in the synthesis of design solutions is shown, also the schemes, that illustrate and explain the introduction of structural optimization in the traditional design of steel frames, are constructed. To solve the problem of synthesis and comparison of design solutions for steel frames, it is proposed to develop the computing facilities that significantly reduces the complexity of search designing and based on the use of methods of structural and parametric optimization.

The impact of slice-reduced computed tomography on histogram-based densitometry assessment of lung fibrosis in patients with systemic sclerosis.

PubMed

Nguyen-Kim, Thi Dan Linh; Maurer, Britta; Suliman, Yossra A; Morsbach, Fabian; Distler, Oliver; Frauenfelder, Thomas

2018-04-01

To evaluate usability of slice-reduced sequential computed tomography (CT) compared to standard high-resolution CT (HRCT) in patients with systemic sclerosis (SSc) for qualitative and quantitative assessment of interstitial lung disease (ILD) with respect to (I) detection of lung parenchymal abnormalities, (II) qualitative and semiquantitative visual assessment, (III) quantification of ILD by histograms and (IV) accuracy for the 20%-cut off discrimination. From standard chest HRCT of 60 SSc patients sequential 9-slice-computed tomography (reduced HRCT) was retrospectively reconstructed. ILD was assessed by visual scoring and quantitative histogram parameters. Results from standard and reduced HRCT were compared using non-parametric tests and analysed by univariate linear regression analyses. With respect to the detection of parenchymal abnormalities, only the detection of intrapulmonary bronchiectasis was significantly lower in reduced HRCT compared to standard HRCT (P=0.039). No differences were found comparing visual scores for fibrosis severity and extension from standard and reduced HRCT (P=0.051-0.073). All scores correlated significantly (P<0.001) to histogram parameters derived from both, standard and reduced HRCT. Significant higher values of kurtosis and skewness for reduced HRCT were found (both P<0.001). In contrast to standard HRCT histogram parameters from reduced HRCT showed significant discrimination at cut-off 20% fibrosis (sensitivity 88% kurtosis and skewness; specificity 81% kurtosis and 86% skewness; cut-off kurtosis ≤26, cut-off skewness ≤4; both P<0.001). Reduced HRCT is a robust method to assess lung fibrosis in SSc with minimal radiation dose with no difference in scoring assessment of lung fibrosis severity and extension in comparison to standard HRCT. In contrast to standard HRCT histogram parameters derived from the approach of reduced HRCT could discriminate at a threshold of 20% lung fibrosis with high sensitivity and specificity. Hence it might be used to detect early disease progression of lung fibrosis in context of monitoring and treatment of SSc patients.

Improved magnetic resonance fingerprinting reconstruction with low-rank and subspace modeling.

PubMed

Zhao, Bo; Setsompop, Kawin; Adalsteinsson, Elfar; Gagoski, Borjan; Ye, Huihui; Ma, Dan; Jiang, Yun; Ellen Grant, P; Griswold, Mark A; Wald, Lawrence L

2018-02-01

This article introduces a constrained imaging method based on low-rank and subspace modeling to improve the accuracy and speed of MR fingerprinting (MRF). A new model-based imaging method is developed for MRF to reconstruct high-quality time-series images and accurate tissue parameter maps (e.g., T 1 , T 2 , and spin density maps). Specifically, the proposed method exploits low-rank approximations of MRF time-series images, and further enforces temporal subspace constraints to capture magnetization dynamics. This allows the time-series image reconstruction problem to be formulated as a simple linear least-squares problem, which enables efficient computation. After image reconstruction, tissue parameter maps are estimated via dictionary-based pattern matching, as in the conventional approach. The effectiveness of the proposed method was evaluated with in vivo experiments. Compared with the conventional MRF reconstruction, the proposed method reconstructs time-series images with significantly reduced aliasing artifacts and noise contamination. Although the conventional approach exhibits some robustness to these corruptions, the improved time-series image reconstruction in turn provides more accurate tissue parameter maps. The improvement is pronounced especially when the acquisition time becomes short. The proposed method significantly improves the accuracy of MRF, and also reduces data acquisition time. Magn Reson Med 79:933-942, 2018. © 2017 International Society for Magnetic Resonance in Medicine. © 2017 International Society for Magnetic Resonance in Medicine.

Diminution of the gut resistome after a gut microbiota-targeted dietary intervention in obese children

PubMed Central

Wu, Guojun; Zhang, Chenhong; Wang, Jing; Zhang, Feng; Wang, Ruirui; Shen, Jian; Wang, Linghua; Pang, Xiaoyan; Zhang, Xiaojun; Zhao, Liping; Zhang, Menghui

2016-01-01

The gut microbiome represents an important reservoir of antibiotic resistance genes (ARGs). Effective methods are urgently needed for managing the gut resistome to fight against the antibiotic resistance threat. In this study, we show that a gut microbiota-targeted dietary intervention, which shifts the dominant fermentation of gut bacteria from protein to carbohydrate, significantly diminished the gut resistome and alleviated metabolic syndrome in obese children. Of the non-redundant metagenomic gene catalog of ~2 × 106 microbial genes, 399 ARGs were identified in 131 gene types and conferred resistance to 47 antibiotics. Both the richness and diversity of the gut resistome were significantly reduced after the intervention. A total of 201 of the 399 ARGs were carried in 120 co-abundance gene groups (CAGs) directly binned from the gene catalog across both pre-and post-intervention samples. The intervention significantly reduced several CAGs in Klebsiella, Enterobacter and Escherichia, which were the major hubs for multiple resistance gene types. Thus, dietary intervention may become a potentially effective method for diminishing the gut resistome. PMID:27044409

Diminution of the gut resistome after a gut microbiota-targeted dietary intervention in obese children.

PubMed

Wu, Guojun; Zhang, Chenhong; Wang, Jing; Zhang, Feng; Wang, Ruirui; Shen, Jian; Wang, Linghua; Pang, Xiaoyan; Zhang, Xiaojun; Zhao, Liping; Zhang, Menghui

2016-04-05

The gut microbiome represents an important reservoir of antibiotic resistance genes (ARGs). Effective methods are urgently needed for managing the gut resistome to fight against the antibiotic resistance threat. In this study, we show that a gut microbiota-targeted dietary intervention, which shifts the dominant fermentation of gut bacteria from protein to carbohydrate, significantly diminished the gut resistome and alleviated metabolic syndrome in obese children. Of the non-redundant metagenomic gene catalog of ~2 × 10(6) microbial genes, 399 ARGs were identified in 131 gene types and conferred resistance to 47 antibiotics. Both the richness and diversity of the gut resistome were significantly reduced after the intervention. A total of 201 of the 399 ARGs were carried in 120 co-abundance gene groups (CAGs) directly binned from the gene catalog across both pre-and post-intervention samples. The intervention significantly reduced several CAGs in Klebsiella, Enterobacter and Escherichia, which were the major hubs for multiple resistance gene types. Thus, dietary intervention may become a potentially effective method for diminishing the gut resistome.

Perturbative universal state-selective correction for state-specific multi-reference coupled cluster methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brabec, Jiri; Banik, Subrata; Kowalski, Karol

2016-10-28

The implementation details of the universal state-selective (USS) multi-reference coupled cluster (MRCC) formalism with singles and doubles (USS(2)) are discussed on the example of several benchmark systems. We demonstrate that the USS(2) formalism is capable of improving accuracies of state specific multi-reference coupled-cluster (MRCC) methods based on the Brillouin-Wigner and Mukherjee’s sufficiency conditions. Additionally, it is shown that the USS(2) approach significantly alleviates problems associated with the lack of invariance of MRCC theories upon the rotation of active orbitals. We also discuss the perturbative USS(2) formulations that significantly reduce numerical overhead of the full USS(2) method.

The influence of pelvic adjustment on vertical jump height in female university students with functional leg length inequality.

PubMed

Gong, Wontae

2015-01-01

[Purpose] This study aimed to investigate the effect of pelvic adjustment on vertical jump height (VJH) in female university students with functional leg length inequality (FLLI). [Subjects] Thirty female university students with FLLI were divided into a pelvic adjustment group (n = 15) and a stretching (control) group (n = 15). [Methods] VJH was measured using an OptoGait. [Results] After the intervention, jump height improved significantly compared with the pre-intervention height only in the pelvic adjustment group, while FLLI showed statistically significant improvement in both groups. [Conclusion] Pelvic adjustment as per the Gonstead method can be applied as a method of reducing FLLI and increasing VJH.

Jointly determining significance levels of primary and replication studies by controlling the false discovery rate in two-stage genome-wide association studies.

PubMed

Jiang, Wei; Yu, Weichuan

2017-01-01

In genome-wide association studies, we normally discover associations between genetic variants and diseases/traits in primary studies, and validate the findings in replication studies. We consider the associations identified in both primary and replication studies as true findings. An important question under this two-stage setting is how to determine significance levels in both studies. In traditional methods, significance levels of the primary and replication studies are determined separately. We argue that the separate determination strategy reduces the power in the overall two-stage study. Therefore, we propose a novel method to determine significance levels jointly. Our method is a reanalysis method that needs summary statistics from both studies. We find the most powerful significance levels when controlling the false discovery rate in the two-stage study. To enjoy the power improvement from the joint determination method, we need to select single nucleotide polymorphisms for replication at a less stringent significance level. This is a common practice in studies designed for discovery purpose. We suggest this practice is also suitable in studies with validation purpose in order to identify more true findings. Simulation experiments show that our method can provide more power than traditional methods and that the false discovery rate is well-controlled. Empirical experiments on datasets of five diseases/traits demonstrate that our method can help identify more associations. The R-package is available at: http://bioinformatics.ust.hk/RFdr.html .

Directly calculated electrical conductivity of hot dense hydrogen from molecular dynamics simulation beyond Kubo-Greenwood formula

NASA Astrophysics Data System (ADS)

Ma, Qian; Kang, Dongdong; Zhao, Zengxiu; Dai, Jiayu

2018-01-01

Electrical conductivity of hot dense hydrogen is directly calculated by molecular dynamics simulation with a reduced electron force field method, in which the electrons are represented as Gaussian wave packets with fixed sizes. Here, the temperature is higher than electron Fermi temperature ( T > 300 eV , ρ = 40 g / cc ). The present method can avoid the Coulomb catastrophe and give the limit of electrical conductivity based on the Coulomb interaction. We investigate the effect of ion-electron coupled movements, which is lost in the static method such as density functional theory based Kubo-Greenwood framework. It is found that the ionic dynamics, which contributes to the dynamical electrical microfield and electron-ion collisions, will reduce the conductivity significantly compared with the fixed ion configuration calculations.

A novel diagnosis method for a Hall plates-based rotary encoder with a magnetic concentrator.

PubMed

Meng, Bumin; Wang, Yaonan; Sun, Wei; Yuan, Xiaofang

2014-07-31

In the last few years, rotary encoders based on two-dimensional complementary metal oxide semiconductors (CMOS) Hall plates with a magnetic concentrator have been developed to measure contactless absolute angle. There are various error factors influencing the measuring accuracy, which are difficult to locate after the assembly of encoder. In this paper, a model-based rapid diagnosis method is presented. Based on an analysis of the error mechanism, an error model is built to compare minimum residual angle error and to quantify the error factors. Additionally, a modified particle swarm optimization (PSO) algorithm is used to reduce the calculated amount. The simulation and experimental results show that this diagnosis method is feasible to quantify the causes of the error and to reduce iteration significantly.

An efficient optimization method to improve the measuring accuracy of oxygen saturation by using triangular wave optical signal

NASA Astrophysics Data System (ADS)

Li, Gang; Yu, Yue; Zhang, Cui; Lin, Ling

2017-09-01

The oxygen saturation is one of the important parameters to evaluate human health. This paper presents an efficient optimization method that can improve the accuracy of oxygen saturation measurement, which employs an optical frequency division triangular wave signal as the excitation signal to obtain dynamic spectrum and calculate oxygen saturation. In comparison to the traditional method measured RMSE (root mean square error) of SpO2 which is 0.1705, this proposed method significantly reduced the measured RMSE which is 0.0965. It is notable that the accuracy of oxygen saturation measurement has been improved significantly. The method can simplify the circuit and bring down the demand of elements. Furthermore, it has a great reference value on improving the signal to noise ratio of other physiological signals.

Effects of furrow irrigation on the growth, production, and water use efficiency of direct sowing rice.

PubMed

He, Chunlin

2010-08-03

Rice farming is the major crop production in Asia and is predicted to increase significantly in the near future in order to meet the demands for the increasing human population. Traditional irrigation methods used in rice farming often result in great water loss. New water-saving methods are urgently needed to reduce water consumption. Three field and pot experiments were conducted to evaluate the furrow irrigation (FI) system to improve water use efficiency (WUE) and production of direct sowing rice in southern China. Compared to the conventional irrigation (CI) system (continuous flooding irrigation), for every square hectometer of rice field, the FI system reduced water use by 3130 m3, or 48.1%, and increased grain production by 13.9% for an early cultivar. For a late cultivar, the FI system reduced water use by 2655 m3, or 40.6%, and an increase of grain production by 12.1%. The improved WUE in the FI system is attributed to (1) a significant reduction of irrigation rate, seepage, evaporation, and evapotranspiration; (2) a significant reduction in the reduced materials, such as ferrous ion (Fe2+), and therefore an increase in the vitality of the root system, evident by the increases in the number of white roots by 32.62%, and decreases in the number of black roots by 20.04% and yellow roots by 12.58%; the use of the FI system may also reduce humidity of the rice field and enhance gas transport in the soil and light penetration, which led to reduced rice diseases and increased leaf vitality; and (3) increases in tiller and effective spikes by 11.53% and the weight per thousand grains by 1.0 g. These findings suggest that the shallow FI system is a promising means for rice farming in areas with increasing water shortages.

Comparison of histomorphometrical data obtained with two different image analysis methods.

PubMed

Ballerini, Lucia; Franke-Stenport, Victoria; Borgefors, Gunilla; Johansson, Carina B

2007-08-01

A common way to determine tissue acceptance of biomaterials is to perform histomorphometrical analysis on histologically stained sections from retrieved samples with surrounding tissue, using various methods. The "time and money consuming" methods and techniques used are often "in house standards". We address light microscopic investigations of bone tissue reactions on un-decalcified cut and ground sections of threaded implants. In order to screen sections and generate results faster, the aim of this pilot project was to compare results generated with the in-house standard visual image analysis tool (i.e., quantifications and judgements done by the naked eye) with a custom made automatic image analysis program. The histomorphometrical bone area measurements revealed no significant differences between the methods but the results of the bony contacts varied significantly. The raw results were in relative agreement, i.e., the values from the two methods were proportional to each other: low bony contact values in the visual method corresponded to low values with the automatic method. With similar resolution images and further improvements of the automatic method this difference should become insignificant. A great advantage using the new automatic image analysis method is that it is time saving--analysis time can be significantly reduced.

Methods and statistics for combining motif match scores.

PubMed

Bailey, T L; Gribskov, M

1998-01-01

Position-specific scoring matrices are useful for representing and searching for protein sequence motifs. A sequence family can often be described by a group of one or more motifs, and an effective search must combine the scores for matching a sequence to each of the motifs in the group. We describe three methods for combining match scores and estimating the statistical significance of the combined scores and evaluate the search quality (classification accuracy) and the accuracy of the estimate of statistical significance of each. The three methods are: 1) sum of scores, 2) sum of reduced variates, 3) product of score p-values. We show that method 3) is superior to the other two methods in both regards, and that combining motif scores indeed gives better search accuracy. The MAST sequence homology search algorithm utilizing the product of p-values scoring method is available for interactive use and downloading at URL http:/(/)www.sdsc.edu/MEME.

Perturbation theory corrections to the two-particle reduced density matrix variational method.

PubMed

Juhasz, Tamas; Mazziotti, David A

2004-07-15

In the variational 2-particle-reduced-density-matrix (2-RDM) method, the ground-state energy is minimized with respect to the 2-particle reduced density matrix, constrained by N-representability conditions. Consider the N-electron Hamiltonian H(lambda) as a function of the parameter lambda where we recover the Fock Hamiltonian at lambda=0 and we recover the fully correlated Hamiltonian at lambda=1. We explore using the accuracy of perturbation theory at small lambda to correct the 2-RDM variational energies at lambda=1 where the Hamiltonian represents correlated atoms and molecules. A key assumption in the correction is that the 2-RDM method will capture a fairly constant percentage of the correlation energy for lambda in (0,1] because the nonperturbative 2-RDM approach depends more significantly upon the nature rather than the strength of the two-body Hamiltonian interaction. For a variety of molecules we observe that this correction improves the 2-RDM energies in the equilibrium bonding region, while the 2-RDM energies at stretched or nearly dissociated geometries, already highly accurate, are not significantly changed. At equilibrium geometries the corrected 2-RDM energies are similar in accuracy to those from coupled-cluster singles and doubles (CCSD), but at nonequilibrium geometries the 2-RDM energies are often dramatically more accurate as shown in the bond stretching and dissociation data for water and nitrogen. (c) 2004 American Institute of Physics.

High-throughput process development: determination of dynamic binding capacity using microtiter filter plates filled with chromatography resin.

PubMed

Bergander, Tryggve; Nilsson-Välimaa, Kristina; Oberg, Katarina; Lacki, Karol M

2008-01-01

Steadily increasing demand for more efficient and more affordable biomolecule-based therapies put a significant burden on biopharma companies to reduce the cost of R&D activities associated with introduction of a new drug to the market. Reducing the time required to develop a purification process would be one option to address the high cost issue. The reduction in time can be accomplished if more efficient methods/tools are available for process development work, including high-throughput techniques. This paper addresses the transitions from traditional column-based process development to a modern high-throughput approach utilizing microtiter filter plates filled with a well-defined volume of chromatography resin. The approach is based on implementing the well-known batch uptake principle into microtiter plate geometry. Two variants of the proposed approach, allowing for either qualitative or quantitative estimation of dynamic binding capacity as a function of residence time, are described. Examples of quantitative estimation of dynamic binding capacities of human polyclonal IgG on MabSelect SuRe and of qualitative estimation of dynamic binding capacity of amyloglucosidase on a prototype of Capto DEAE weak ion exchanger are given. The proposed high-throughput method for determination of dynamic binding capacity significantly reduces time and sample consumption as compared to a traditional method utilizing packed chromatography columns without sacrificing the accuracy of data obtained.

Bicarbonate trigger for inducing lipid accumulation in algal systems

DOEpatents

Gardner, Robert; Peyton, Brent; Cooksey, Keith E.

2015-08-04

The present invention provides bicarbonate containing and/or bicarbonate-producing compositions and methods to induce lipid accumulation in an algae growth system, wherein the algae growth system is under light-dark cycling condition. By adding said compositions at a specific growth stage, said methods lead to much higher lipid accumulation and/or significantly reduced total time required for accumulating lipid in the algae growth system.

Ethanol production from lignocellulose

DOEpatents

Ingram, Lonnie O.; Wood, Brent E.

2001-01-01

This invention presents a method of improving enzymatic degradation of lignocellulose, as in the production of ethanol from lignocellulosic material, through the use of ultrasonic treatment. The invention shows that ultrasonic treatment reduces cellulase requirements by 1/3 to 1/2. With the cost of enzymes being a major problem in the cost-effective production of ethanol from lignocellulosic material, this invention presents a significant improvement over presently available methods.

Importance sampling variance reduction for the Fokker–Planck rarefied gas particle method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collyer, B.S., E-mail: benjamin.collyer@gmail.com; London Mathematical Laboratory, 14 Buckingham Street, London WC2N 6DF; Connaughton, C.

The Fokker–Planck approximation to the Boltzmann equation, solved numerically by stochastic particle schemes, is used to provide estimates for rarefied gas flows. This paper presents a variance reduction technique for a stochastic particle method that is able to greatly reduce the uncertainty of the estimated flow fields when the characteristic speed of the flow is small in comparison to the thermal velocity of the gas. The method relies on importance sampling, requiring minimal changes to the basic stochastic particle scheme. We test the importance sampling scheme on a homogeneous relaxation, planar Couette flow and a lid-driven-cavity flow, and find thatmore » our method is able to greatly reduce the noise of estimated quantities. Significantly, we find that as the characteristic speed of the flow decreases, the variance of the noisy estimators becomes independent of the characteristic speed.« less

How to deal with morning bad breath: A randomized, crossover clinical trial

PubMed Central

Oliveira-Neto, Jeronimo M.; Sato, Sandra; Pedrazzi, Vinícius

2013-01-01

Context: The absence of a protocol for the treatment of halitosis has led us to compare mouthrinses with mechanical oral hygiene procedures for treating morning breath by employing a hand-held sulfide monitor. Aims: To compare the efficacy of five modalities of treatment for controlling morning halitosis in subjects with no dental or periodontal disease. Settings and Design: This is a five-period, randomized, crossover clinical trial. Materials and Methods: Twenty volunteers were randomly assigned to the trial. Testing involved the use of a conventional tongue scraper, a tongue scraper joined to the back of a toothbrush's head, two mouthrinses (0.05% cetylpyridinium chloride and 0.12% chlorhexidine digluconate) and a soft-bristled toothbrush and fluoride toothpaste for practicing oral hygiene. Statistical Analysis Used: Data analysis was performed using SPSS version 17 for Windows and NCSS 2007 software (P < 0.05). The products and the periods were compared with each other using the Friedman's test. When significant differences (P < 0.05) were determined, the products and periods were compared in pairs by using the Wilcoxon's test and by adjusting the original significance level (0.05) for multiple comparisons by using the Bonferroni's method. Results: The toothbrush's tongue scraper was able to significantly reduce bad breath for up to 2 h. Chlorhexidine reduced bad breath only at the end of the second hour, an effect that lasted for 3 h. Conclusions: Mechanical tongue cleaning was able to immediately reduce bad breath for a short period, whereas chlorhexidine and mechanical oral hygiene reduced bad breath for longer periods, achieving the best results against morning breath. PMID:24554886

Iterative image-domain decomposition for dual-energy CT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Niu, Tianye; Dong, Xue; Petrongolo, Michael

2014-04-15

Purpose: Dual energy CT (DECT) imaging plays an important role in advanced imaging applications due to its capability of material decomposition. Direct decomposition via matrix inversion suffers from significant degradation of image signal-to-noise ratios, which reduces clinical values of DECT. Existing denoising algorithms achieve suboptimal performance since they suppress image noise either before or after the decomposition and do not fully explore the noise statistical properties of the decomposition process. In this work, the authors propose an iterative image-domain decomposition method for noise suppression in DECT, using the full variance-covariance matrix of the decomposed images. Methods: The proposed algorithm ismore » formulated in the form of least-square estimation with smoothness regularization. Based on the design principles of a best linear unbiased estimator, the authors include the inverse of the estimated variance-covariance matrix of the decomposed images as the penalty weight in the least-square term. The regularization term enforces the image smoothness by calculating the square sum of neighboring pixel value differences. To retain the boundary sharpness of the decomposed images, the authors detect the edges in the CT images before decomposition. These edge pixels have small weights in the calculation of the regularization term. Distinct from the existing denoising algorithms applied on the images before or after decomposition, the method has an iterative process for noise suppression, with decomposition performed in each iteration. The authors implement the proposed algorithm using a standard conjugate gradient algorithm. The method performance is evaluated using an evaluation phantom (Catphan©600) and an anthropomorphic head phantom. The results are compared with those generated using direct matrix inversion with no noise suppression, a denoising method applied on the decomposed images, and an existing algorithm with similar formulation as the proposed method but with an edge-preserving regularization term. Results: On the Catphan phantom, the method maintains the same spatial resolution on the decomposed images as that of the CT images before decomposition (8 pairs/cm) while significantly reducing their noise standard deviation. Compared to that obtained by the direct matrix inversion, the noise standard deviation in the images decomposed by the proposed algorithm is reduced by over 98%. Without considering the noise correlation properties in the formulation, the denoising scheme degrades the spatial resolution to 6 pairs/cm for the same level of noise suppression. Compared to the edge-preserving algorithm, the method achieves better low-contrast detectability. A quantitative study is performed on the contrast-rod slice of Catphan phantom. The proposed method achieves lower electron density measurement error as compared to that by the direct matrix inversion, and significantly reduces the error variation by over 97%. On the head phantom, the method reduces the noise standard deviation of decomposed images by over 97% without blurring the sinus structures. Conclusions: The authors propose an iterative image-domain decomposition method for DECT. The method combines noise suppression and material decomposition into an iterative process and achieves both goals simultaneously. By exploring the full variance-covariance properties of the decomposed images and utilizing the edge predetection, the proposed algorithm shows superior performance on noise suppression with high image spatial resolution and low-contrast detectability.« less

GUIDE TO CLEANER TECHNOLOGIES: ALTERNATIVE METAL FINISHES

EPA Science Inventory

A cleaner technology is a source reduction or recycle method applied to eliminate or significantly reduce the amount of any hazardous substance, pollutant, or contaminant released to the environment. The emphasis of cleaner technologies is on process changes that can prevent poll...

Joint Contracture Orthosis (JCO)

NASA Technical Reports Server (NTRS)

Lunsford, Thomas R.; Parsons, Ken; Krouskop, Thomas; McGee, Kevin

1997-01-01

The purpose of this project was to develop an advanced orthosis which is effective in reducing upper and lower limb contractures in significantly less time than currently required with conventional methods. The team that developed the JCO consisted of an engineer, orthotist, therapist, and physician.

Finite element dynamic analysis of soft tissues using state-space model.

PubMed

Iorga, Lucian N; Shan, Baoxiang; Pelegri, Assimina A

2009-04-01

A finite element (FE) model is employed to investigate the dynamic response of soft tissues under external excitations, particularly corresponding to the case of harmonic motion imaging. A solid 3D mixed 'u-p' element S8P0 is implemented to capture the near-incompressibility inherent in soft tissues. Two important aspects in structural modelling of these tissues are studied; these are the influence of viscous damping on the dynamic response and, following FE-modelling, a developed state-space formulation that valuates the efficiency of several order reduction methods. It is illustrated that the order of the mathematical model can be significantly reduced, while preserving the accuracy of the observed system dynamics. Thus, the reduced-order state-space representation of soft tissues for general dynamic analysis significantly reduces the computational cost and provides a unitary framework for the 'forward' simulation and 'inverse' estimation of soft tissues. Moreover, the results suggest that damping in soft-tissue is significant, effectively cancelling the contribution of all but the first few vibration modes.

Factors affecting nursing staff use of a communication tool to reduce potentially preventable acute care transfers in long-term care.

PubMed

Ballard, Stephanie A; Peretti, Matteo; Lungu, Ovidiu; Voyer, Philippe; Tabamo, Fruan; Alfonso, Linda; Cetin-Sahin, Deniz; Johnson, Sarasa M A; Wilchesky, Machelle

Although specialized communication tools can effectively reduce acute care transfers, few studies have assessed the factors that may influence the use of such tools by nursing staff at the individual level. We evaluated the associations between years of experience, tool-related training, nursing attitudes, and intensity of use of a communication tool developed to reduce transfers in a long-term care facility. We employed a mixed methods design using data from medical charts, electronic records, and semi-structured interviews. Experienced nurses used the tool significantly less than inexperienced nurses, and training had a significant positive impact on tool use. Nurses found the purpose of the tool to be confusing. No significant differences in attitude were observed based on years of experience or intensity of use. Project findings indicate that focused efforts to enrich training may increase intervention adherence. Experienced nurses in particular should be made aware of the benefits of utilizing communication tools. Copyright © 2017 Elsevier Inc. All rights reserved.

Impact of a Comprehensive Workplace Hand Hygiene Program on Employer Health Care Insurance Claims and Costs, Absenteeism, and Employee Perceptions and Practices

PubMed Central

Arbogast, James W.; Moore-Schiltz, Laura; Jarvis, William R.; Harpster-Hagen, Amanda; Hughes, Jillian; Parker, Albert

2016-01-01

Objective: The aim of this study was to determine the efficacy of a multimodal hand hygiene intervention program in reducing health care insurance claims for hygiene preventable infections (eg, cold and influenza), absenteeism, and subjective impact on employees. Methods: A 13.5-month prospective, randomized cluster controlled trial was executed with alcohol-based hand sanitizer in strategic workplace locations and personal use (intervention group) and brief hand hygiene education (both groups). Four years of retrospective data were collected for all participants. Results: Hygiene-preventable health care claims were significantly reduced in the intervention group by over 20% (P < 0.05). Absenteeism was positively impacted overall for the intervention group. Employee survey data showed significant improvements in hand hygiene behavior and perception of company concern for employee well-being. Conclusion: Providing a comprehensive, targeted, yet simple to execute hand hygiene program significantly reduced the incidence of health care claims and increased employee workplace satisfaction. PMID:27281645

Anal wall sparing effect of an endorectal balloon in 3D conformal and intensity-modulated prostate radiotherapy.

PubMed

Smeenk, Robert Jan; van Lin, Emile N J Th; van Kollenburg, Peter; Kunze-Busch, Martina; Kaanders, Johannes H A M

2009-10-01

To investigate the anal wall (Awall) sparing effect of an endorectal balloon (ERB) in 3D conformal radiotherapy (3D-CRT) and intensity-modulated radiotherapy (IMRT) for prostate cancer. In 24 patients with localized prostate carcinoma, two planning CT-scans were performed: with and without ERB. A prostate planning target volume (PTV) was defined, and the Awall was delineated, using two different methods. Three-field and 4-field 3D-CRT plans, and IMRT plans were generated with a prescription dose of 78Gy. In 144 treatment plans, the minimum dose (D(min)), maximum dose (D(max)), and mean dose (D(mean)) to the Awall were calculated, as well as the Awall volumes exposed to doses ranging from >or=20Gy to >or=70Gy (V(20)-V(70), respectively). In the 3D-CRT plans, an ERB significantly reduced D(mean), D(max), and V(30)-V(70). For IMRT all investigated dose parameters were significantly reduced by the ERB. The absolute reduction of D(mean) was 12Gy in 3D-CRT and was 7.5Gy in IMRT for both methods of Awall delineation. Application of an ERB showed a significant Awall sparing effect in both 3D-CRT and IMRT. This may lead to reduced late anal toxicity in prostate radiotherapy.

Energy absorption is reduced with oleic acid supplements in human short bowel syndrome.

PubMed

Compher, Charlene W; Kinosian, Bruce P; Rubesin, Stephen E; Ratcliffe, Sarah J; Metz, David C

2009-01-01

Oleic acid premeal supplements have been described as a method to trigger the ileal brake and thus lengthen transit time and the opportunity for nutrient absorption. The aims of this study were to determine whether oleic acid supplements would lengthen transit time and improve absorption of nutrients in study participants with short bowel syndrome as well as affect diarrhea or patient weight. A double-blind, controlled, random-order crossover trial was conducted in 8 study participants with longstanding and severe short bowel syndrome, employing blue food color appearance, breath hydrogen testing, and radio-opaque markers as measures of transit time. Absorption of energy, protein, fat, and fluid was conducted by classic nutrient balance methods. Diarrhea was estimated by daily stool weight and number of bowel actions. Although 8 patients were enrolled, only 7 completed the study. Transit time was not significantly different between oleic acid and placebo treatment, although peptide YY levels trended higher with the oleic acid treatment. Energy absorption was reduced 14% by oleic acid, significantly more than the 3% reduction by placebo. Fat, protein, and fluid absorption was not changed significantly. Neither diarrhea nor patient body weight was changed by oleic acid. Energy absorption is reduced by oleic acid supplements in severe short bowel syndrome. The study may have lacked power to determine whether oleic acid affects diarrhea or body weight.

Analysis of drugs in human tissues by supercritical fluid extraction/immunoassay

NASA Astrophysics Data System (ADS)

Furton, Kenneth G.; Sabucedo, Alberta; Rein, Joseph; Hearn, W. L.

1997-02-01

A rapid, readily automated method has been developed for the quantitative analysis of phenobarbital from human liver tissues based on supercritical carbon dioxide extraction followed by fluorescence enzyme immunoassay. The method developed significantly reduces sample handling and utilizes the entire liver homogenate. The current method yields comparable recoveries and precision and does not require the use of an internal standard, although traditional GC/MS confirmation can still be performed on sample extracts. Additionally, the proposed method uses non-toxic, inexpensive carbon dioxide, thus eliminating the use of halogenated organic solvents.

Accurate evaluation of exchange fields in finite element micromagnetic solvers

NASA Astrophysics Data System (ADS)

Chang, R.; Escobar, M. A.; Li, S.; Lubarda, M. V.; Lomakin, V.

2012-04-01

Quadratic basis functions (QBFs) are implemented for solving the Landau-Lifshitz-Gilbert equation via the finite element method. This involves the introduction of a set of special testing functions compatible with the QBFs for evaluating the Laplacian operator. The results by using QBFs are significantly more accurate than those via linear basis functions. QBF approach leads to significantly more accurate results than conventionally used approaches based on linear basis functions. Importantly QBFs allow reducing the error of computing the exchange field by increasing the mesh density for structured and unstructured meshes. Numerical examples demonstrate the feasibility of the method.

The sensitivity of relative toxicity rankings by the USF/NASA test method to some test variables

NASA Technical Reports Server (NTRS)

Hilado, C. J.; Labossiere, L. A.; Leon, H. A.; Kourtides, D. A.; Parker, J. A.; Hsu, M.-T. S.

1976-01-01

Pyrolysis temperature and the distance between the source and sensor of effluents are two important variables in tests for relative toxicity. Modifications of the USF/NASA toxicity screening test method to increase the upper temperature limit of pyrolysis, reduce the distance between the sample and the test animals, and increase the chamber volume available for animal occupancy, did not significantly alter rankings of relative toxicity of four representative materials. The changes rendered some differences no longer significant, but did not reverse any rankings. The materials studied were cotton, wool, aromatic polyamide, and polybenzimidazole.

Hepatocurative potential of sesquiterpene lactones of Taraxacum officinale on carbon tetrachloride induced liver toxicity in mice.

PubMed

Mahesh, A; Jeyachandran, R; Cindrella, L; Thangadurai, D; Veerapur, V P; Muralidhara Rao, D

2010-06-01

The hepatocurative potential of ethanolic extract (ETO) and sesquiterpene lactones enriched fraction (SL) of Taraxacum officinale roots was evaluated against carbon tetrachloride (CCl 4 ) induced hepatotoxicity in mice. The diagnostic markers such as alanine aminotransferase (ALT), aspartate aminotransferase (AST), alkaline phosphatase (ALP) and total bilirubin contents were significantly elevated, whereas significant reduction in the level of reduced glutathione (GSH) and enhanced hepatic lipid peroxidation, liver weight and liver protein were observed in CCl 4 induced hepatotoxicity in mice. Post-treatment with ETO and SL significantly protected the hepatotoxicity as evident from the lower levels of hepatic enzyme markers, such as serum transaminase (ALT, AST), ALP and total bilirubin. Further, significant reduction in the liver weight and liver protein in drug-treated hepatotoxic mice and also reduced oxidative stress by increasing reduced glutathione content and decreasing lipid peroxidation level has been noticed. The histopathological evaluation of the liver also revealed that ETO and SL reduced the incidence of liver lesions induced by CCl 4 . The results indicate that sesquiterpene lactones have a protective effect against acute hepatotoxicity induced by the administration of CCl 4 in mice. Furthermore, observed activity of SL may be due to the synergistic action of two sesquiterpene lactones identified from enriched ethyl acetate fraction by HPLC method.

Potential therapeutic and protective effect of curcumin against stroke in the male albino stroke-induced model rats.

PubMed

Zhang, Yuanyuan; Yan, Yi; Cao, Yi; Yang, Yongtao; Zhao, Qing; Jing, Rui; Hu, Jiayi; Bao, Juan

2017-08-15

The present study was carried out to understand the therapeutic effect of curcumin (CUR) against stroke in the experimental animal model. The study investigates the healing effect of CUR on mitochondrial dysfunction and inflammation. Male albino, Wistar strain rats were used for the induction of middle cerebral artery occlusion (MCAO), and reperfusion. Enzyme-linked immunosorbent assay (ELISA) was used for the determination of interleukin 6 (IL-6) and tumor necrosis factor alpha (TNF-α) in the brain region. Western blot analysis was used to determine the protein expression levels of Bax, Bcl-2, p53, and Sirt1. The water level was determined in brain region by using standard method. Experimental results indicated that the use of CUR significantly reduced brain edema and water content. IL-6 and TNF-α were significantly reduced in the brain region following use of CUR. Mitochondrial membrane potential (MMP) also reduced significantly after CUR treatment. Protein expression of p53 and Bax were significantly reduced, whereas Bcl-2 and Sirt1 were increased following CUR treatment. Taking all these data together, it is suggested that the use of CUR may be a potential therapeutic agent for the treatment of stroke. Copyright © 2017 Elsevier Inc. All rights reserved.

A data-driven approach for denoising GNSS position time series

NASA Astrophysics Data System (ADS)

Li, Yanyan; Xu, Caijun; Yi, Lei; Fang, Rongxin

2017-12-01

Global navigation satellite system (GNSS) datasets suffer from common mode error (CME) and other unmodeled errors. To decrease the noise level in GNSS positioning, we propose a new data-driven adaptive multiscale denoising method in this paper. Both synthetic and real-world long-term GNSS datasets were employed to assess the performance of the proposed method, and its results were compared with those of stacking filtering, principal component analysis (PCA) and the recently developed multiscale multiway PCA. It is found that the proposed method can significantly eliminate the high-frequency white noise and remove the low-frequency CME. Furthermore, the proposed method is more precise for denoising GNSS signals than the other denoising methods. For example, in the real-world example, our method reduces the mean standard deviation of the north, east and vertical components from 1.54 to 0.26, 1.64 to 0.21 and 4.80 to 0.72 mm, respectively. Noise analysis indicates that for the original signals, a combination of power-law plus white noise model can be identified as the best noise model. For the filtered time series using our method, the generalized Gauss-Markov model is the best noise model with the spectral indices close to - 3, indicating that flicker walk noise can be identified. Moreover, the common mode error in the unfiltered time series is significantly reduced by the proposed method. After filtering with our method, a combination of power-law plus white noise model is the best noise model for the CMEs in the study region.

Temporal Decompostion of a Distribution System Quasi-Static Time-Series Simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mather, Barry A; Hunsberger, Randolph J

This paper documents the first phase of an investigation into reducing runtimes of complex OpenDSS models through parallelization. As the method seems promising, future work will quantify - and further mitigate - errors arising from this process. In this initial report, we demonstrate how, through the use of temporal decomposition, the run times of a complex distribution-system-level quasi-static time series simulation can be reduced roughly proportional to the level of parallelization. Using this method, the monolithic model runtime of 51 hours was reduced to a minimum of about 90 minutes. As expected, this comes at the expense of control- andmore » voltage-errors at the time-slice boundaries. All evaluations were performed using a real distribution circuit model with the addition of 50 PV systems - representing a mock complex PV impact study. We are able to reduce induced transition errors through the addition of controls initialization, though small errors persist. The time savings with parallelization are so significant that we feel additional investigation to reduce control errors is warranted.« less

Method to Reduce Target Motion Through Needle-Tissue Interactions.

PubMed

Oldfield, Matthew J; Leibinger, Alexander; Seah, Tian En Timothy; Rodriguez Y Baena, Ferdinando

2015-11-01

During minimally invasive surgical procedures, it is often important to deliver needles to particular tissue volumes. Needles, when interacting with a substrate, cause deformation and target motion. To reduce reliance on compensatory intra-operative imaging, a needle design and novel delivery mechanism is proposed. Three-dimensional finite element simulations of a multi-segment needle inserted into a pre-existing crack are presented. The motion profiles of the needle segments are varied to identify methods that reduce target motion. Experiments are then performed by inserting a needle into a gelatine tissue phantom and measuring the internal target motion using digital image correlation. Simulations indicate that target motion is reduced when needle segments are stroked cyclically and utilise a small amount of retraction instead of being held stationary. Results are confirmed experimentally by statistically significant target motion reductions of more than 8% during cyclic strokes and 29% when also incorporating retraction, with the same net insertion speed. By using a multi-segment needle and taking advantage of frictional interactions on the needle surface, it is demonstrated that target motion ahead of an advancing needle can be substantially reduced.

Potential Impact of Graphic Health Warnings on Cigarette Packages in Reducing Cigarette Demand and Smoking-Related Deaths in Vietnam.

PubMed

Minh, Hoang Van; Chung, Le Hong; Giang, Kim Bao; Duc, Duong Minh; Hinh, Nguyen Duc; Mai, Vu Quynh; Cuong, Nguyen Manh; Manh, Pham Duc; Duc, Ha Anh; Yang, Jui-Chen

2016-01-01

Two years after implementation of the graphic health warning intervention in Vietnam, it is very important to evaluate the intervention's potential impact. The objective of this paper was to predict effects of graphic health warnings on cigarette packages, particularly in reducing cigarette demand and smoking-associated deaths in Vietnam. In this study, a discrete choice experiment (DCE) method was used to evaluate the potential impact of graphic tobacco health warnings on smoking demand. To predict the impact of GHWs on reducing premature deaths associated with smoking, we constructed different static models. We adapted the method developed by University of Toronto, Canada and found that GHWs had statistically significant impact on reducing cigarette demand (up to 10.1% through images of lung damage), resulting in an overall decrease of smoking prevalence in Vietnam. We also found that between 428,417- 646,098 premature deaths would be prevented as a result of the GHW intervention. The potential impact of the GHW labels on reducing premature smoking-associated deaths in Vietnam were shown to be stronger among lower socio-economic groups.

Vitamin D binding protein isoforms as candidate predictors of disease extension in childhood arthritis

PubMed Central

Gibson, David S.; Newell, Keri; Evans, Alexandra N.; Finnegan, Sorcha; Manning, Gwen; Scaife, Caitriona; McAllister, Catherine; Pennington, Stephen R.; Duncan, Mark W.; Moore, Terry L.; Rooney, Madeleine E.

2012-01-01

Introduction. Juvenile idiopathic arthritis (JIA) comprises a poorly understood group of chronic autoimmune diseases with variable clinical outcomes. We investigated whether the synovial fluid (SF) proteome could distinguish a subset of patients in whom disease extends to affect a large number of joints. Methods. SF samples from 57 patients were obtained around time of initial diagnosis of JIA, labeled with Cy dyes and separated by two-dimensional electrophoresis. Multivariate analyses were used to isolate a panel of proteins which distinguish patient subgroups. Proteins were identified using MALDI-TOF mass spectrometry with expression verified by immunochemical methods. Protein glycosylation status was confirmed by hydrophilic interaction liquid chromatography. Results. A truncated isoform of vitamin D binding protein (VDBP) is present at significantly reduced levels in the SF of oligoarticular patients at risk of disease extension, relative to other subgroups (p < 0.05). Furthermore, sialylated forms of immunopurified synovial VDBP were significantly reduced in extended oligoarticular patients (p < 0.005). Conclusion. Reduced conversion of VDBP to a macrophage activation factor may be used to stratify patients to determine risk of disease extension in JIA patients. PMID:22771520

Analyzing locomotion synthesis with feature-based motion graphs.

PubMed

Mahmudi, Mentar; Kallmann, Marcelo

2013-05-01

We propose feature-based motion graphs for realistic locomotion synthesis among obstacles. Among several advantages, feature-based motion graphs achieve improved results in search queries, eliminate the need of postprocessing for foot skating removal, and reduce the computational requirements in comparison to traditional motion graphs. Our contributions are threefold. First, we show that choosing transitions based on relevant features significantly reduces graph construction time and leads to improved search performances. Second, we employ a fast channel search method that confines the motion graph search to a free channel with guaranteed clearance among obstacles, achieving faster and improved results that avoid expensive collision checking. Lastly, we present a motion deformation model based on Inverse Kinematics applied over the transitions of a solution branch. Each transition is assigned a continuous deformation range that does not exceed the original transition cost threshold specified by the user for the graph construction. The obtained deformation improves the reachability of the feature-based motion graph and in turn also reduces the time spent during search. The results obtained by the proposed methods are evaluated and quantified, and they demonstrate significant improvements in comparison to traditional motion graph techniques.

Facile synthesis of hierarchical dendritic PtPd nanogarlands supported on reduced graphene oxide with enhanced electrocatalytic properties

NASA Astrophysics Data System (ADS)

Li, Shan-Shan; Zheng, Jie-Ning; Ma, Xiaohong; Hu, Yuan-Yuan; Wang, Ai-Jun; Chen, Jian-Rong; Feng, Jiu-Ju

2014-05-01

A simple and facile method is developed for one-pot preparation of hierarchical dendritic PtPd nanogarlands supported on reduced graphene oxide (PtPd/RGO) at room temperature, without using any seed, organic solvent, or complex apparatus. It is found that octylphenoxypolyethoxyethanol (NP-40) as a soft template and its amount are critical to the formation of PtPd garlands. The as-prepared nanocomposites are further applied to methanol and ethanol oxidation with significantly enhanced electrocatalytic activity and better stability in alkaline media.A simple and facile method is developed for one-pot preparation of hierarchical dendritic PtPd nanogarlands supported on reduced graphene oxide (PtPd/RGO) at room temperature, without using any seed, organic solvent, or complex apparatus. It is found that octylphenoxypolyethoxyethanol (NP-40) as a soft template and its amount are critical to the formation of PtPd garlands. The as-prepared nanocomposites are further applied to methanol and ethanol oxidation with significantly enhanced electrocatalytic activity and better stability in alkaline media. Electronic supplementary information (ESI) available: Experimental section, Fig. S1-S12 and Tables S1 and S2. See DOI: 10.1039/c3nr06808k

[Early activation of heart-operated patients as a tool for optimization of cardio-surgery curation (review)].

PubMed

2014-04-01

During last years in foreign countries there was widely introduced tactic of early activation of cardio-surgery patients. Necessary components of this methodical approach are early finishing of post-operation artificial respiration and extubation of trachea, shortening of time spending in intensive therapy till 1 day and sign out from stationary after 5 days. As a result of reducing hospitalization period, the curation costs are reduced significantly. Goal of this research was the analysis of methods of anesthesia that allow early extubation and activation after cardio-surgery interventions. There were analyzed data of protocols of anesthesia and post-operation periods for 270 patients. It was concluded that applied methods of anesthesia ensure adequate protection from operation stress and allow reduce time of post-operation artificial respiration, early activation of patients without reducing level of their safety. It was also proved that application of any type of anesthesia medicines is not influencing the temp of post-operation activation. Conducted research is proving the advisability of using tactic of early activation of patients after heart operations and considers this as a tool for optimization of cardio-surgery curation.

Improving multi-objective reservoir operation optimization with sensitivity-informed problem decomposition

NASA Astrophysics Data System (ADS)

Chu, J. G.; Zhang, C.; Fu, G. T.; Li, Y.; Zhou, H. C.

2015-04-01

This study investigates the effectiveness of a sensitivity-informed method for multi-objective operation of reservoir systems, which uses global sensitivity analysis as a screening tool to reduce the computational demands. Sobol's method is used to screen insensitive decision variables and guide the formulation of the optimization problems with a significantly reduced number of decision variables. This sensitivity-informed problem decomposition dramatically reduces the computational demands required for attaining high quality approximations of optimal tradeoff relationships between conflicting design objectives. The search results obtained from the reduced complexity multi-objective reservoir operation problems are then used to pre-condition the full search of the original optimization problem. In two case studies, the Dahuofang reservoir and the inter-basin multi-reservoir system in Liaoning province, China, sensitivity analysis results show that reservoir performance is strongly controlled by a small proportion of decision variables. Sensitivity-informed problem decomposition and pre-conditioning are evaluated in their ability to improve the efficiency and effectiveness of multi-objective evolutionary optimization. Overall, this study illustrates the efficiency and effectiveness of the sensitivity-informed method and the use of global sensitivity analysis to inform problem decomposition when solving the complex multi-objective reservoir operation problems.

Testing and modeling the influence of reclamation and control methods for reducing nonpoint mercury emissions associated with industrial open pit gold mines.

PubMed

Miller, Matthieu B; Gustin, Mae S

2013-06-01

Industrial gold mining is a significant source of mercury (Hg) emission to the atmosphere. To investigate ways to reduce these emissions, reclamation and dust and mercury control methods used at open pit gold mining operations in Nevada were studied in a laboratory setting. Using this information along with field data, and building off previous work, total annual Hg emissions were estimated for two active gold mines in northern Nevada. Results showed that capping mining waste materials with a low-Hg substrate can reduce Hg emissions from 50 to nearly 100%. The spraying of typical dust control solutions often results in higher Hg emissions, especially as materials dry after application. The concentrated application of a dithiocarbamate Hg control reagent appears to reduce Hg emissions, but further testing mimicking the actual distribution of this chemical within an active leach solution is needed to make a more definitive assessment.

Microbial Shifts in the Intestinal Microbiota of Salmonella Infected Chickens in Response to Enrofloxacin

PubMed Central

Li, Jun; Hao, Haihong; Cheng, Guyue; Liu, Chunbei; Ahmed, Saeed; Shabbir, Muhammad A. B.; Hussain, Hafiz I.; Dai, Menghong; Yuan, Zonghui

2017-01-01

Fluoroquinolones (FQs) are important antibiotics used for treatment of Salmonella infection in poultry in many countries. However, oral administration of fluoroquinolones may affect the composition and abundance of a number of bacterial taxa in the chicken intestine. Using 16S rRNA gene sequencing, the microbial shifts in the gut of Salmonella infected chickens in response to enrofloxacin treatments at different dosages (0, 0.1, 4, and 100 mg/kg b.w.) were quantitatively evaluated. The results showed that the shedding levels of Salmonella were significantly reduced in the high dosage group as demonstrated by both the culturing method and 16S rRNA sequencing method. The average values of diversity indices were higher in the control group than in the three medicated groups. Non-metric multidimensional scaling (NMDS) analysis results showed that the microbial community of high dosage group was clearly separated from the other three groups. In total, 25 genera were significantly enriched (including 6 abundant genera: Lactococcus, Bacillus, Burkholderia, Pseudomonas, Rhizobium, and Acinetobacter) and 23 genera were significantly reduced in the medicated groups than in the control group for the treatment period, but these bacterial taxa recovered to normal levels after therapy withdrawal. Additionally, 5 genera were significantly reduced in both treatment and withdrawal periods (e.g., Blautia and Anaerotruncus) and 23 genera (e.g., Enterobacter and Clostridium) were significantly decreased only in the withdrawal period, indicating that these genera might be the potential targets for the fluoroquinolones antimicrobial effects. Specially, Enterococcus was significantly reduced under high dosage of enrofloxacin treatment, while significantly enriched in the withdrawal period, which was presumably due to the resistance selection. Predicted microbial functions associated with genetic information processing were significantly decreased in the high dosage group. Overall, enrofloxacin at a dosage of 100 mg/kg b.w. significantly altered the microbial community membership and structure, and microbial functions in the chicken intestine during the medication. This study fully investigates the chicken intestinal microbiota in response to enrofloxacin treatment and identifies potential targets against which the fluoroquinolones may have potent antimicrobial effects. These results provide insights into the effects of the usage of enrofloxacin on chicken and will aid in the prudent and rational use of antibiotics in poultry industry. PMID:28943868

Microbial Shifts in the Intestinal Microbiota of Salmonella Infected Chickens in Response to Enrofloxacin.

PubMed

Li, Jun; Hao, Haihong; Cheng, Guyue; Liu, Chunbei; Ahmed, Saeed; Shabbir, Muhammad A B; Hussain, Hafiz I; Dai, Menghong; Yuan, Zonghui

2017-01-01

Fluoroquinolones (FQs) are important antibiotics used for treatment of Salmonella infection in poultry in many countries. However, oral administration of fluoroquinolones may affect the composition and abundance of a number of bacterial taxa in the chicken intestine. Using 16S rRNA gene sequencing, the microbial shifts in the gut of Salmonella infected chickens in response to enrofloxacin treatments at different dosages (0, 0.1, 4, and 100 mg/kg b.w.) were quantitatively evaluated. The results showed that the shedding levels of Salmonella were significantly reduced in the high dosage group as demonstrated by both the culturing method and 16S rRNA sequencing method. The average values of diversity indices were higher in the control group than in the three medicated groups. Non-metric multidimensional scaling (NMDS) analysis results showed that the microbial community of high dosage group was clearly separated from the other three groups. In total, 25 genera were significantly enriched (including 6 abundant genera: Lactococcus , Bacillus , Burkholderia , Pseudomonas , Rhizobium , and Acinetobacter ) and 23 genera were significantly reduced in the medicated groups than in the control group for the treatment period, but these bacterial taxa recovered to normal levels after therapy withdrawal. Additionally, 5 genera were significantly reduced in both treatment and withdrawal periods (e.g., Blautia and Anaerotruncus ) and 23 genera (e.g., Enterobacter and Clostridium ) were significantly decreased only in the withdrawal period, indicating that these genera might be the potential targets for the fluoroquinolones antimicrobial effects. Specially, Enterococcus was significantly reduced under high dosage of enrofloxacin treatment, while significantly enriched in the withdrawal period, which was presumably due to the resistance selection. Predicted microbial functions associated with genetic information processing were significantly decreased in the high dosage group. Overall, enrofloxacin at a dosage of 100 mg/kg b.w. significantly altered the microbial community membership and structure, and microbial functions in the chicken intestine during the medication. This study fully investigates the chicken intestinal microbiota in response to enrofloxacin treatment and identifies potential targets against which the fluoroquinolones may have potent antimicrobial effects. These results provide insights into the effects of the usage of enrofloxacin on chicken and will aid in the prudent and rational use of antibiotics in poultry industry.

The Application of Simulation Method in Isothermal Elastic Natural Gas Pipeline

NASA Astrophysics Data System (ADS)

Xing, Chunlei; Guan, Shiming; Zhao, Yue; Cao, Jinggang; Chu, Yanji

2018-02-01

This Elastic pipeline mathematic model is of crucial importance in natural gas pipeline simulation because of its compliance with the practical industrial cases. The numerical model of elastic pipeline will bring non-linear complexity to the discretized equations. Hence the Newton-Raphson method cannot achieve fast convergence in this kind of problems. Therefore A new Newton Based method with Powell-Wolfe Condition to simulate the Isothermal elastic pipeline flow is presented. The results obtained by the new method aregiven based on the defined boundary conditions. It is shown that the method converges in all cases and reduces significant computational cost.

Novel method for fast characterization of high-surface-area electrocatalytic materials using carbon fiber microelectrode.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Strmcnik, D.; Hodnik, N.; Hocevar, S. B.

2010-02-18

A carbon fiber microelectrode (CFME) was used for characterization of the nanoparticle catalysts as an alternative to the well-established rotating disk electrode (RDE) method. We found that the novel CFME method yielded comparable results to the RDE method when investigating the adsorption/desorption processes as well the specific activity for reactions such as the oxygen reduction reaction. Its major advantage over the RDE method is a fast sample preparation and rapid measurement, reducing significantly the time of a single sample characterization from 2-3 h to a favorable 5-10 min.

Evaluation of a Mass-Media Campaign to Increase the Awareness of the Need to Reduce Discretionary Salt Use in the South African Population.

PubMed

Wentzel-Viljoen, Edelweiss; Steyn, Krisela; Lombard, Carl; De Villiers, Anniza; Charlton, Karen; Frielinghaus, Sabine; Crickmore, Christelle; Mungal-Singh, Vash

2017-11-12

The South African strategic plan to reduce cardiovascular disease (CVD) includes reducing population salt intake to less than 5 g/day. A mass media campaign was undertaken to increase public awareness of the association between high salt intake, blood pressure and CVD, and focused on the reduction of discretionary salt intake. Community based surveys, before and after the campaign, were conducted in a cohort of black women aged 18-55 years. Questions on knowledge, attitudes and beliefs regarding salt use were asked. Current interest in engaging with salt reduction behaviors was assessed using the "stage of change" model. Five hundred fifty women participated in the baseline study and 477 in the follow-up survey. Most of the indicators of knowledge, attitudes and behavior change show a significant move towards considering and initiating reduced salt consumption. Post intervention, significantly more participants reported that they were taking steps to control salt intake (38% increased to 59.5%, p < 0.0001). In particular, adding salt while cooking and at the table occurred significantly less frequently. The findings suggest that mass media campaigns may be an effective tool to use as part of a strategy to reduce discretionary consumption of salt among the population along with other methods.

Effectiveness of an intervention for reducing social stigma towards mental illness in adolescents

PubMed Central

Vila-Badia, Regina; Martínez-Zambrano, Francisco; Arenas, Otilia; Casas-Anguera, Emma; García-Morales, Esther; Villellas, Raúl; Martín, José Ramón; Pérez-Franco, María Belén; Valduciel, Tamara; Casellas, Diana; García-Franco, Mar; Miguel, Jose; Balsera, Joaquim; Pascual, Gemma; Julia, Eugènia; Ochoa, Susana

2016-01-01

AIM: To evaluate the effectiveness of an intervention for reducing social stigma towards mental illness in adolescents. The effect of gender and knowledge of someone with mental illness was measured. METHODS: Two hundred and eighty secondary school students were evaluated using the Community Attitudes towards Mental Illness (CAMI) questionnaire. The schools were randomized and some received the intervention and others acted as the control group. The programme consisted of providing information via a documentary film and of contact with healthcare staff in order to reduce the social stigma within the school environment. RESULTS: The intervention was effective in reducing the CAMI authoritarianism and social restrictiveness subscales. The intervention showed significant changes in girls in terms of authoritarianism and social restrictiveness, while boys only showed significant changes in authoritarianism. Following the intervention, a significant reduction was found in authoritarianism and social restrictiveness in those who knew someone with mental illness, and only in authoritarianism in those who did not know anyone with mental illness. CONCLUSION: The intervention was effective to reduce social stigma towards people with mental illness, especially in the area of authoritarianism. Some differences were found depending on gender and whether or not the subjects knew someone with mental illness. PMID:27354967

A tri-modality image fusion method for target delineation of brain tumors in radiotherapy.

PubMed

Guo, Lu; Shen, Shuming; Harris, Eleanor; Wang, Zheng; Jiang, Wei; Guo, Yu; Feng, Yuanming

2014-01-01

To develop a tri-modality image fusion method for better target delineation in image-guided radiotherapy for patients with brain tumors. A new method of tri-modality image fusion was developed, which can fuse and display all image sets in one panel and one operation. And a feasibility study in gross tumor volume (GTV) delineation using data from three patients with brain tumors was conducted, which included images of simulation CT, MRI, and 18F-fluorodeoxyglucose positron emission tomography (18F-FDG PET) examinations before radiotherapy. Tri-modality image fusion was implemented after image registrations of CT+PET and CT+MRI, and the transparency weight of each modality could be adjusted and set by users. Three radiation oncologists delineated GTVs for all patients using dual-modality (MRI/CT) and tri-modality (MRI/CT/PET) image fusion respectively. Inter-observer variation was assessed by the coefficient of variation (COV), the average distance between surface and centroid (ADSC), and the local standard deviation (SDlocal). Analysis of COV was also performed to evaluate intra-observer volume variation. The inter-observer variation analysis showed that, the mean COV was 0.14(± 0.09) and 0.07(± 0.01) for dual-modality and tri-modality respectively; the standard deviation of ADSC was significantly reduced (p<0.05) with tri-modality; SDlocal averaged over median GTV surface was reduced in patient 2 (from 0.57 cm to 0.39 cm) and patient 3 (from 0.42 cm to 0.36 cm) with the new method. The intra-observer volume variation was also significantly reduced (p = 0.00) with the tri-modality method as compared with using the dual-modality method. With the new tri-modality image fusion method smaller inter- and intra-observer variation in GTV definition for the brain tumors can be achieved, which improves the consistency and accuracy for target delineation in individualized radiotherapy.

Acceleration of GPU-based Krylov solvers via data transfer reduction

DOE PAGES

Anzt, Hartwig; Tomov, Stanimire; Luszczek, Piotr; ...

2015-04-08

Krylov subspace iterative solvers are often the method of choice when solving large sparse linear systems. At the same time, hardware accelerators such as graphics processing units continue to offer significant floating point performance gains for matrix and vector computations through easy-to-use libraries of computational kernels. However, as these libraries are usually composed of a well optimized but limited set of linear algebra operations, applications that use them often fail to reduce certain data communications, and hence fail to leverage the full potential of the accelerator. In this study, we target the acceleration of Krylov subspace iterative methods for graphicsmore » processing units, and in particular the Biconjugate Gradient Stabilized solver that significant improvement can be achieved by reformulating the method to reduce data-communications through application-specific kernels instead of using the generic BLAS kernels, e.g. as provided by NVIDIA’s cuBLAS library, and by designing a graphics processing unit specific sparse matrix-vector product kernel that is able to more efficiently use the graphics processing unit’s computing power. Furthermore, we derive a model estimating the performance improvement, and use experimental data to validate the expected runtime savings. Finally, considering that the derived implementation achieves significantly higher performance, we assert that similar optimizations addressing algorithm structure, as well as sparse matrix-vector, are crucial for the subsequent development of high-performance graphics processing units accelerated Krylov subspace iterative methods.« less

Application of multiattribute decision-making methods for the determination of relative significance factor of impact categories.

PubMed

Noh, Jaesung; Lee, Kun Mo

2003-05-01

A relative significance factor (f(i)) of an impact category is the external weight of the impact category. The objective of this study is to propose a systematic and easy-to-use method for the determination of f(i). Multiattribute decision-making (MADM) methods including the analytical hierarchy process (AHP), the rank-order centroid method, and the fuzzy method were evaluated for this purpose. The results and practical aspects of using the three methods are compared. Each method shows the same trend, with minor differences in the value of f(i). Thus, all three methods can be applied to the determination of f(i). The rank order centroid method reduces the number of pairwise comparisons by placing the alternatives in order, although it has inherent weakness over the fuzzy method in expressing the degree of vagueness associated with assigning weights to criteria and alternatives. The rank order centroid method is considered a practical method for the determination of f(i) because it is easier and simpler to use compared to the AHP and the fuzzy method.

Development of cost-effective surfactant flooding technology. First annual report for the period, September 30, 1992--September 29, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pope, G.A.; Sepehrnoori, K.

1994-08-01

This research consists of the parallel development of a new chemical flooding simulator and the application of existing UTCHEM simulation code to model surfactant flooding. The new code is based upon a completely new numerical method that combines for the first time higher order finite difference methods, flux limiters, and implicit algorithms. Early results indicate that this approach has significant advantages in some problems and will likely enable simulation of much larger and more realistic chemical floods once it is fully developed. Additional improvements have also been made to the UTCHEM code and it has been applied for the firstmore » time to the study of stochastic reservoirs with and without horizontal wells to evaluate methods to reduce the cost and risk of surfactant flooding. During the first year of this contract, significant progress has been made on both of these tasks. The authors have found that there are indeed significant differences between the performance predictions based upon the traditional layered reservoir description and the more realistic and flexible descriptions using geostatistics. These preliminary studies of surfactant flooding using horizontal wells shows that although they have significant potential to greatly reduce project life and thus improve the economics of the process, their use requires accurate reservoir descriptions and simulations to be effective. Much more needs to be done to fully understand and optimize their use and develop reliable design criteria.« less

Flexible, multi-measurement guided wave damage detection under varying temperatures

NASA Astrophysics Data System (ADS)

Douglass, Alexander C. S.; Harley, Joel B.

2018-04-01

Temperature compensation in structural health monitoring helps identify damage in a structure by removing data variations due to environmental conditions, such as temperature. Stretch-based methods are one of the most commonly used temperature compensation methods. To account for variations in temperature, stretch-based methods optimally stretch signals in time to optimally match a measurement to a baseline. All of the data is then compared with the single baseline to determine the presence of damage. Yet, for these methods to be effective, the measurement and the baseline must satisfy the inherent assumptions of the temperature compensation method. In many scenarios, these assumptions are wrong, the methods generate error, and damage detection fails. To improve damage detection, a multi-measurement damage detection method is introduced. By using each measurement in the dataset as a baseline, error caused by imperfect temperature compensation is reduced. The multi-measurement method increases the detection effectiveness of our damage metric, or damage indicator, over time and reduces the presence of additional peaks caused by temperature that could be mistaken for damage. By using many baselines, the variance of the damage indicator is reduced and the effects from damage are amplified. Notably, the multi-measurement improves damage detection over single-measurement methods. This is demonstrated through an increase in the maximum of our damage signature from 0.55 to 0.95 (where large values, up to a maximum of one, represent a statistically significant change in the data due to damage).

Network model of project "Lean Production"

NASA Astrophysics Data System (ADS)

Khisamova, E. D.

2018-05-01

Economical production implies primarily new approaches to culture of management and organization of production and offers a set of tools and techniques that allows reducing losses significantly and making the process cheaper and faster. Economical production tools are simple solutions that allow one to see opportunities for improvement of all aspects of the business, to reduce losses significantly, to constantly improve the whole spectrum of business processes, to increase significantly the transparency and manageability of the organization, to take advantage of the potential of each employee of the company, to increase competitiveness, and to obtain significant economic benefits without making large financial expenditures. Each of economical production tools solves a specific part of the problems, and only application of their combination will allow one to solve the problem or minimize it to acceptable values. The research of the governance process project "Lean Production" permitted studying the methods and tools of lean production and developing measures for their improvement.

A PCA aided cross-covariance scheme for discriminative feature extraction from EEG signals.

PubMed

Zarei, Roozbeh; He, Jing; Siuly, Siuly; Zhang, Yanchun

2017-07-01

Feature extraction of EEG signals plays a significant role in Brain-computer interface (BCI) as it can significantly affect the performance and the computational time of the system. The main aim of the current work is to introduce an innovative algorithm for acquiring reliable discriminating features from EEG signals to improve classification performances and to reduce the time complexity. This study develops a robust feature extraction method combining the principal component analysis (PCA) and the cross-covariance technique (CCOV) for the extraction of discriminatory information from the mental states based on EEG signals in BCI applications. We apply the correlation based variable selection method with the best first search on the extracted features to identify the best feature set for characterizing the distribution of mental state signals. To verify the robustness of the proposed feature extraction method, three machine learning techniques: multilayer perceptron neural networks (MLP), least square support vector machine (LS-SVM), and logistic regression (LR) are employed on the obtained features. The proposed methods are evaluated on two publicly available datasets. Furthermore, we evaluate the performance of the proposed methods by comparing it with some recently reported algorithms. The experimental results show that all three classifiers achieve high performance (above 99% overall classification accuracy) for the proposed feature set. Among these classifiers, the MLP and LS-SVM methods yield the best performance for the obtained feature. The average sensitivity, specificity and classification accuracy for these two classifiers are same, which are 99.32%, 100%, and 99.66%, respectively for the BCI competition dataset IVa and 100%, 100%, and 100%, for the BCI competition dataset IVb. The results also indicate the proposed methods outperform the most recently reported methods by at least 0.25% average accuracy improvement in dataset IVa. The execution time results show that the proposed method has less time complexity after feature selection. The proposed feature extraction method is very effective for getting representatives information from mental states EEG signals in BCI applications and reducing the computational complexity of classifiers by reducing the number of extracted features. Copyright © 2017 Elsevier B.V. All rights reserved.

Communicating and Translating EPA's Computational Toxicology Research (WC10)

EPA Science Inventory

US EPA’s National Center for Computational Toxicology (NCCT) develops and uses alternative testing methods to accelerate the pace of chemical evaluations, reduce reliance on animal testing, and address the significant lack of chemical data. The chemical data is generated through ...

Methane on the greenhouse agenda

NASA Technical Reports Server (NTRS)

Hogan, Kathleen B.; Hoffman, John S.; Thompson, Anne M.

1991-01-01

Options for reducing methane emissions, which could have a significant effect on global warming, are addressed. Emissions from landfills, coal mining, oil and natural gas systems, ruminants, animal wastes and wastewater, rice cultivation, and biomass burning are considered. Methods for implementing these emission reductions are discussed.

ITS technologies reduce delay, crashes and emissions, with significant returns on investment : research spotlight.

DOT National Transportation Integrated Search

2015-07-01

Intelligent transportation systems (ITS) technologies have gained popularity in recent years as a method for relieving road congestion and improving safety through better traf c and incident management. Since 2006, MDOT has invested more than $100 mi...

Overset Grid Methods Applied to Nonlinear Potential Flows

NASA Technical Reports Server (NTRS)

Holst, Terry; Kwak, Dochan (Technical Monitor)

2000-01-01

The objectives of this viewgraph presentation are to develop Chimera-based potential methodology which is compatible with overflow and overflow infrastructure, creating options for an advanced problem solving environment and to significantly reduce turnaround time for aerodynamic analysis and design (primarily cruise conditions).

ADVANCED COMPUTATIONAL METHODS IN DOSE MODELING: APPLICATION OF COMPUTATIONAL BIOPHYSICAL TRANSPORT, COMPUTATIONAL CHEMISTRY, AND COMPUTATIONAL BIOLOGY

EPA Science Inventory

Computational toxicology (CompTox) leverages the significant gains in computing power and computational techniques (e.g., numerical approaches, structure-activity relationships, bioinformatics) realized over the last few years, thereby reducing costs and increasing efficiency i...

Advanced Testing Method for Ground Thermal Conductivity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Xiaobing; Clemenzi, Rick; Liu, Su

A new method is developed that can quickly and more accurately determine the effective ground thermal conductivity (GTC) based on thermal response test (TRT) results. Ground thermal conductivity is an important parameter for sizing ground heat exchangers (GHEXs) used by geothermal heat pump systems. The conventional GTC test method usually requires a TRT for 48 hours with a very stable electric power supply throughout the entire test. In contrast, the new method reduces the required test time by 40%–60% or more, and it can determine GTC even with an unstable or intermittent power supply. Consequently, it can significantly reduce themore » cost of GTC testing and increase its use, which will enable optimal design of geothermal heat pump systems. Further, this new method provides more information about the thermal properties of the GHEX and the ground than previous techniques. It can verify the installation quality of GHEXs and has the potential, if developed, to characterize the heterogeneous thermal properties of the ground formation surrounding the GHEXs.« less

Failure Bounding And Sensitivity Analysis Applied To Monte Carlo Entry, Descent, And Landing Simulations

NASA Technical Reports Server (NTRS)

Gaebler, John A.; Tolson, Robert H.

2010-01-01

In the study of entry, descent, and landing, Monte Carlo sampling methods are often employed to study the uncertainty in the designed trajectory. The large number of uncertain inputs and outputs, coupled with complicated non-linear models, can make interpretation of the results difficult. Three methods that provide statistical insights are applied to an entry, descent, and landing simulation. The advantages and disadvantages of each method are discussed in terms of the insights gained versus the computational cost. The first method investigated was failure domain bounding which aims to reduce the computational cost of assessing the failure probability. Next a variance-based sensitivity analysis was studied for the ability to identify which input variable uncertainty has the greatest impact on the uncertainty of an output. Finally, probabilistic sensitivity analysis is used to calculate certain sensitivities at a reduced computational cost. These methods produce valuable information that identifies critical mission parameters and needs for new technology, but generally at a significant computational cost.

Modification method to reduce the impact of blood vessel on noncontact discrimination of human blood based on ;M+N; theory

NASA Astrophysics Data System (ADS)

Zhang, Linna; Ding, Hongyan; Lin, Ling; Wang, Yimin; Guo, Xin

2018-01-01

Noncontact discriminating human blood is significantly crucial for import-export ports and inspection and quarantine departments. We had already demonstrated that visible diffuse reflectance spectroscopy combining PLS-DA method can successfully realize noncontact human blood discrimination. However, the circulated blood vessels may be produced with different materials. The use of various kinds of blood tubes may have a negative effect on the discrimination, based on ;M+N; theory (Li et al., 2016). In this research, we explored the impact of different material of blood vessels, such as glass tube and plastic tube, on the prediction ability of the discrimination model. Furthermore, we searched for the modification method to reduce the influence from the blood tubes. Our work indicated that generalized diffuse reflectance method can greatly improve the discrimination accuracy. This research can greatly facilitate the application of noncontact discrimination method based on visible and near-infrared diffuse reflectance spectroscopy.

ERROR REDUCTION IN DUCT LEAKAGE TESTING THROUGH DATA CROSS-CHECKS

DOE Office of Scientific and Technical Information (OSTI.GOV)

ANDREWS, J.W.

1998-12-31

One way to reduce uncertainty in scientific measurement is to devise a protocol in which more quantities are measured than are absolutely required, so that the result is over constrained. This report develops a method for so combining data from two different tests for air leakage in residential duct systems. An algorithm, which depends on the uncertainty estimates for the measured quantities, optimizes the use of the excess data. In many cases it can significantly reduce the error bar on at least one of the two measured duct leakage rates (supply or return), and it provides a rational method ofmore » reconciling any conflicting results from the two leakage tests.« less

Adaptive single-pixel imaging with aggregated sampling and continuous differential measurements

NASA Astrophysics Data System (ADS)

Huo, Yaoran; He, Hongjie; Chen, Fan; Tai, Heng-Ming

2018-06-01

This paper proposes an adaptive compressive imaging technique with one single-pixel detector and single arm. The aggregated sampling (AS) method enables the reduction of resolutions of the reconstructed images. It aims to reduce the time and space consumption. The target image with a resolution up to 1024 × 1024 can be reconstructed successfully at the 20% sampling rate. The continuous differential measurement (CDM) method combined with a ratio factor of significant coefficient (RFSC) improves the imaging quality. Moreover, RFSC reduces the human intervention in parameter setting. This technique enhances the practicability of single-pixel imaging with the benefits from less time and space consumption, better imaging quality and less human intervention.

Developments in neonatal technology continue to improve infant outcomes.

PubMed

Noble, Lawrence

2003-09-01

The past 20 years have yielded little success in reducing prematurity rates or decreasing the major morbidities of premature infants. Determination of interventions to decrease prematurity rates, and the development of methods to reduce premature neurologic damage, are the challenges for the next 20 years. With the advent of genetic analysis and the ability to study environmental and genetic interactions, we may be on the threshold of another significant decrease in mortality and morbidity in the premature infant.

Impact of Interventions to Reduce Alzheimer’s Disease Pathology on the Prevalence of Dementia in the Oldest-Old

PubMed Central

Brookmeyer, Ron; Kawas, Claudia H.; Abdallah, Nada; Paganini-Hill, Annlia; Kim, Ronald C.; Corrada, Maria M.

2016-01-01

Introduction The number of persons aged over 90 years will grow significantly in coming decades. This group has the highest rates of dementia, most commonly Alzheimer’s disease (AD). Methods Using The 90+ Study we developed a statistical model for dementia risk based on brain pathologies. Intervention scenarios which reduce or eliminate AD pathology were considered and the numbers of dementia cases among the U.S. oldest-old that could be prevented were estimated. Results U.S. dementia prevalence among the oldest-old will increase from 1.35 million in 2015 to 4.72 million in 2050.If interventions eliminate AD pathology, dementia prevalence would be reduced by approximately 50%, averting nearly 2.4 million cases in 2050. However, large numbers of dementia cases would still remain. Discussion Reducing AD pathology would significantly decrease the public health burden of dementia. However, other interventions are needed to address the burden associated with other dementing pathologies prevalent in the oldest-old. PMID:26900132

Efficacy of a radiation absorbing shield in reducing dose to the interventionalist during peripheral endovascular procedures: a single centre pilot study.

PubMed

Power, S; Mirza, M; Thakorlal, A; Ganai, B; Gavagan, L D; Given, M F; Lee, M J

2015-06-01

This prospective pilot study was undertaken to evaluate the feasibility and effectiveness of using a radiation absorbing shield to reduce operator dose from scatter during lower limb endovascular procedures. A commercially available bismuth shield system (RADPAD) was used. Sixty consecutive patients undergoing lower limb angioplasty were included. Thirty procedures were performed without the RADPAD (control group) and thirty with the RADPAD (study group). Two separate methods were used to measure dose to a single operator. Thermoluminescent dosimeter (TLD) badges were used to measure hand, eye, and unshielded body dose. A direct dosimeter with digital readout was also used to measure eye and unshielded body dose. To allow for variation between control and study groups, dose per unit time was calculated. TLD results demonstrated a significant reduction in median body dose per unit time for the study group compared with controls (p = 0.001), corresponding to a mean dose reduction rate of 65 %. Median eye and hand dose per unit time were also reduced in the study group compared with control group, however, this was not statistically significant (p = 0.081 for eye, p = 0.628 for hand). Direct dosimeter readings also showed statistically significant reduction in median unshielded body dose rate for the study group compared with controls (p = 0.037). Eye dose rate was reduced for the study group but this was not statistically significant (p = 0.142). Initial results are encouraging. Use of the shield resulted in a statistically significant reduction in unshielded dose to the operator's body. Measured dose to the eye and hand of operator were also reduced but did not reach statistical significance in this pilot study.

Use of phenyl/tetrazolyl-functionalized magnetic microspheres and stable isotope labeled internal standards for significant reduction of matrix effect in determination of nine fluoroquinolones by liquid chromatography-quadrupole linear ion trap mass spectrometry.

PubMed

Xu, Fei; Liu, Feng; Wang, Chaozhan; Wei, Yinmao

2018-02-01

In this study, the strategy of unique adsorbent combined with isotope labeled internal standards was used to significantly reduce the matrix effect for the enrichment and analysis of nine fluoroquinolones in a complex sample by liquid chromatography coupled to quadrupole linear ion trap mass spectrometry (LC-QqQ LIT -MS/MS). The adsorbent was prepared conveniently by functionalizing Fe 3 O 4 @SiO 2 microspheres with phenyl and tetrazolyl groups, which could adsorb fluoroquinolones selectively via hydrophobic, electrostatic, and π-π interactions. The established magnetic solid-phase extraction (MSPE) method as well as using stable isotope labeled internal standards in the next MS/MS detection was able to reduce the matrix effect significantly. In the process of LC-QqQ LIT -MS/MS analysis, the precursor and product ions of the analytes were monitored quantitatively and qualitatively on a QTrap system equipped simultaneously with the multiple reaction monitoring (MRM) and enhanced product ion (EPI) scan. Subsequently, the enrichment method combined with LC-QqQ LIT -MS/MS demonstrated good analytical features in terms of linearity (7.5-100.0 ng mL -1 , r > 0.9960), satisfactory recoveries (88.6%-118.3%) with RSDs < 12.0%, LODs = 0.5 μg kg -1 and LOQs = 1.5 μg kg -1 for all tested analytes. Finally, the developed MSPE-LC-QqQ LIT -MS/MS method had been successfully applied to real pork samples for food-safety risk monitoring in Ningxia Province, China. Graphical abstract Mechanism of reducing matrix effect through the as-prepared adsorbent.

Investigating the Effect of Extracorporeal Shock Wave Therapy on Reducing Chronic Pain in Patients with Pes Anserine Bursitis: A Randomized, Clinical- Controlled Trial

PubMed Central

Khosrawi, Saeid; Taheri, Parisa; Ketabi, Marziyeh

2017-01-01

Background: Knee pain, is one of the most common causes of patients’ referring to physiatric clinics, and several factors, are involved in its creation. One of these factors is pes anserine bursitis (PAB) for which various treatment methods are used. This study aims to investigate the effect of this method on reducing chronic pain in these patients. Materials and Methods: This clinical trial was conducted in 2013- 2014 on patients with PAB referring to academic, physical medicine clinics. The patients with chronic PAB (pain duration more than 3 months), who were refractory to conservative treatments, were randomly divided into two 20-member experimental groups (extracorporeal shock wave therapy [ESWT] and sham ESWT). Pain scores of all patients were measured using the Visual Analog Scale (VAS) and McGill Pain Questionnaire (MPQ) (total and present pain indexes [TPIs and PPIs]) before intervention, immediately after intervention (3rd week), and after 8 weeks. The pain scores were then compared and statistically analyzed. Results: In the ESWT group, the mean patient pain score of the VAS and TPI in MPQ were significantly lower than in the sham ESWT group immediately after intervention (3rd week): P =0.02, P = 0.04 respectively; and 8 weeks after the end of treatment: P =0.01, P = 0.000. Moreover, the PPI in both groups had significantly decreased over time, although in ESWT group this decrement was significantly more than sham ESWT group (P < 0.001). Conclusion: The results showed that ESWT could be effective in reducing the pain and treating PAB. PMID:28626745

Reduced Operating Time but Not Blood Loss With Cruciate Retaining Total Knee Arthroplasty

PubMed Central

Vermesan, Dinu; Trocan, Ilie; Prejbeanu, Radu; Poenaru, Dan V; Haragus, Horia; Gratian, Damian; Marrelli, Massimo; Inchingolo, Francesco; Caprio, Monica; Cagiano, Raffaele; Tatullo, Marco

2015-01-01

Background There is no consensus regarding the use of retaining or replacing cruciate implants for patients with limited deformity who undergo a total knee replacement. Scope of this paper is to evaluate whether a cruciate sparing total knee replacement could have a reduced operating time compared to a posterior stabilized implant. Methods For this purpose, we performed a randomized study on 50 subjects. All procedures were performed by a single surgeon in the same conditions to minimize bias and only knees with a less than 20 varus deviation and/or maximum 15° fixed flexion contracture were included. Results Surgery time was significantly shorter with the cruciate retaining implant (P = 0.0037). The mean duration for the Vanguard implant was 68.9 (14.7) and for the NexGen II Legacy was 80.2 (11.3). A higher range of motion, but no significant Knee Society Scores at 6 months follow-up, was used as controls. Conclusions In conclusion, both implants had the potential to assure great outcomes. However, if a decision has to be made, choosing a cruciate retaining procedure could significantly reduce the surgical time. When performed under tourniquet, this gain does not lead to reduced blood loss. PMID:25584102

Metformin reduces lipid accumulation in macrophages by inhibiting FOXO1-mediated transcription of fatty acid-binding protein 4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Jun; Division of Cardiothoracic Surgery, Michael E. DeBakey Department of Surgery, Baylor College of Medicine, Houston, TX; Texas Heart Institute at St. Luke's Episcopal Hospital, Houston, TX

2010-02-26

Objective: The accumulation of lipids in macrophages contributes to the development of atherosclerosis. Strategies to reduce lipid accumulation in macrophages may have therapeutic potential for preventing and treating atherosclerosis and cardiovascular complications. The antidiabetic drug metformin has been reported to reduce lipid accumulation in adipocytes. In this study, we examined the effects of metformin on lipid accumulation in macrophages and investigated the mechanisms involved. Methods and results: We observed that metformin significantly reduced palmitic acid (PA)-induced intracellular lipid accumulation in macrophages. Metformin promoted the expression of carnitine palmitoyltransferase I (CPT-1), while reduced the expression of fatty acid-binding protein 4 (FABP4)more » which was involved in PA-induced lipid accumulation. Quantitative real-time PCR showed that metformin regulates FABP4 expression at the transcriptional level. We identified forkhead transcription factor FOXO1 as a positive regulator of FABP4 expression. Inhibiting FOXO1 expression with FOXO1 siRNA significantly reduced basal and PA-induced FABP4 expression. Overexpression of wild-type FOXO1 and constitutively active FOXO1 significantly increased FABP4 expression, whereas dominant negative FOXO1 dramatically decreased FABP4 expression. Metformin reduced FABP4 expression by promoting FOXO1 nuclear exclusion and subsequently inhibiting its activity. Conclusions: Taken together, these results suggest that metformin reduces lipid accumulation in macrophages by repressing FOXO1-mediated FABP4 transcription. Thus, metformin may have a protective effect against lipid accumulation in macrophages and may serve as a therapeutic agent for preventing and treating atherosclerosis in metabolic syndrome.« less

Unsteady Flow Simulation: A Numerical Challenge

DTIC Science & Technology

2003-03-01

drive to convergence the numerical unsteady term. The time marching procedure is based on the approximate implicit Newton method for systems of non...computed through analytical derivatives of S. The linear system stemming from equation (3) is solved at each integration step by the same iterative method...significant reduction of memory usage, thanks to the reduced dimensions of the linear system matrix during the implicit marching of the solution. The

New Trends in Two-Way Time and Frequency Transfer via Satellite

DTIC Science & Technology

1999-12-01

Recent developments performed with SATRE two-way time transfer ( TWSTFT ) modems resulted in significant performance upgrades and operational...improvements of the TWSTFT method These are aimed to reduce : manpower effort and to provide reliable, real-time data via a centralized monitoring and...collection have been used throughout the experiment INTRODUCTION Two-Way Time and Frequency Transfer via Satellite ( TWSTFT ) is a well established method to

[Effect of twirling-reinforcing-reducing needling manipulations on contents of serum acetylcholine and arterial NOS and cGMP in stress-induced hypertension rats].

PubMed

Liu, Wei; Zhu, Ling-Qun; Chen, Si-Si; Lu, Shu-Chao; Tang, Jie; Liu, Qing-Guo

2015-04-01

To observe the effect of twirling-reinforcing or reducing needling manipulations on plasma acetylcholine (Ach) content and expression of nitric oxide synthetase (NOS) and cyclic guanosine monophosphate (cGMP) in thoracic artery tissue in stress-induced hypertension rats. A total of 60 male rats were randomly divided into blank control, model, acupuncture (no-needle-manipulation) , twirling-reinforcing needling and twirling-reducing needling groups (n = 12 in each group). The stress hypertension model was established by giving the animals with noise and electric shock stimulation (paw), twice a day for 15 days. Acupuncture stimulation was applied to bilateral "Taichong" (LR 3) for 1 min, followed by retaining the needles for 20 min. The treatment was conducted once daily for 7 days. Systolic blood pressure of the rat's tail was detected with non-invasive method and plasma Ach, and NOS and cGMP contents in the thoracic artery tissue were measured using ELISA method. Compared with the control group, the systolic blood pressure was significantly higher in the model group after 15 days' stress stimulation (P < 0.01), while the contents of plasma Ach, arterial NOS and cGMP were markedly down-regulated (P < 0.01). Following 7 days' acupuncture interventions, the increased blood pressure was down-regulated in the no-needle-manipulation, twirling-reinforcing needling and twirling-reducing needling groups (P < 0.05, P < 0.01); and the decreased Ach and NOS in the 3 treatment groups, and cGMP levels in the twirling-reinforcing and twirling-reducing needling groups were remarkably up-regulated (P < 0.01, P < 0.05). No significant change of arterial cGMP content was found in the no-needle-manipulation group (P > 0.05). The effect of the twirling-reducing needling was superior to that of no-needle-manipulation and twirling-reinforcing needling in lowering blood pressure and raising plasma Ach content (P < 0.05, P < 0.01). The twirling-reducing needling of acupuncture has a significant anti-hypertensive effect in stress hypertension rats, which may be associated with its effects in raising blood Ach, and arterial NOS and cGMP levels.

Heuristic Modeling for TRMM Lifetime Predictions

NASA Technical Reports Server (NTRS)

Jordan, P. S.; Sharer, P. J.; DeFazio, R. L.

1996-01-01

Analysis time for computing the expected mission lifetimes of proposed frequently maneuvering, tightly altitude constrained, Earth orbiting spacecraft have been significantly reduced by means of a heuristic modeling method implemented in a commercial-off-the-shelf spreadsheet product (QuattroPro) running on a personal computer (PC). The method uses a look-up table to estimate the maneuver frequency per month as a function of the spacecraft ballistic coefficient and the solar flux index, then computes the associated fuel use by a simple engine model. Maneuver frequency data points are produced by means of a single 1-month run of traditional mission analysis software for each of the 12 to 25 data points required for the table. As the data point computations are required only a mission design start-up and on the occasion of significant mission redesigns, the dependence on time consuming traditional modeling methods is dramatically reduced. Results to date have agreed with traditional methods to within 1 to 1.5 percent. The spreadsheet approach is applicable to a wide variety of Earth orbiting spacecraft with tight altitude constraints. It will be particularly useful to such missions as the Tropical Rainfall Measurement Mission scheduled for launch in 1997, whose mission lifetime calculations are heavily dependent on frequently revised solar flux predictions.

Prospective and retrospective high order eddy current mitigation for diffusion weighted echo planar imaging.

PubMed

Xu, Dan; Maier, Joseph K; King, Kevin F; Collick, Bruce D; Wu, Gaohong; Peters, Robert D; Hinks, R Scott

2013-11-01

The proposed method is aimed at reducing eddy current (EC) induced distortion in diffusion weighted echo planar imaging, without the need to perform further image coregistration between diffusion weighted and T2 images. These ECs typically have significant high order spatial components that cannot be compensated by preemphasis. High order ECs are first calibrated at the system level in a protocol independent fashion. The resulting amplitudes and time constants of high order ECs can then be used to calculate imaging protocol specific corrections. A combined prospective and retrospective approach is proposed to apply correction during data acquisition and image reconstruction. Various phantom, brain, body, and whole body diffusion weighted images with and without the proposed method are acquired. Significantly reduced image distortion and misregistration are consistently seen in images with the proposed method compared with images without. The proposed method is a powerful (e.g., effective at 48 cm field of view and 30 cm slice coverage) and flexible (e.g., compatible with other image enhancements and arbitrary scan plane) technique to correct high order ECs induced distortion and misregistration for various diffusion weighted echo planar imaging applications, without the need for further image post processing, protocol dependent prescan, or sacrifice in signal-to-noise ratio. Copyright © 2013 Wiley Periodicals, Inc.

Clinical effect of reducing curing times with high-intensity LED lights

PubMed Central

Ward, Justin D.; Wolf, Bethany J.; Leite, Luis P.; Zhou, Jing

2016-01-01

Objective To evaluate the clinical performance of brackets cured with a high-intensity, light-emitting diode (LED) with a shorter curing time. Materials and Methods Thirty-four patients and a total of 680 brackets were examined using a randomized split-mouth design. The maxillary right and mandibular left quadrants were cured for 6 seconds with a high-intensity LED light (3200 mW/cm2) and the maxillary left and mandibular right quadrants were cured for 20 seconds with a standard-intensity LED light (1200 mW/cm2). Alternating patients had the quadrants inverted for the curing protocol. The number and date of each first-time bracket failure was recorded from 199 to 585 days posttreatment. Results The bracket failure rate was 1.18% for both curing methods. The proportion of bracket failure was not significantly different between curing methods (P = 1.000), genders (P = 1.000), jaws (P = .725), sides (P = .725), or quadrants (P = .547). Posterior teeth exhibited a greater proportion of failures (2.21%) relative to anterior teeth (0.49%), although the difference was not statistically significant (P = .065). Conclusions No difference was found in bond failure rates between the two curing methods. Both methods showed bond failure rates low enough to be considered clinically sufficient. The high-intensity LED light used with a shorter curing time may be considered an advantage due to the reduced chair time. PMID:25760887

Topic detection using paragraph vectors to support active learning in systematic reviews.

PubMed

Hashimoto, Kazuma; Kontonatsios, Georgios; Miwa, Makoto; Ananiadou, Sophia

2016-08-01

Systematic reviews require expert reviewers to manually screen thousands of citations in order to identify all relevant articles to the review. Active learning text classification is a supervised machine learning approach that has been shown to significantly reduce the manual annotation workload by semi-automating the citation screening process of systematic reviews. In this paper, we present a new topic detection method that induces an informative representation of studies, to improve the performance of the underlying active learner. Our proposed topic detection method uses a neural network-based vector space model to capture semantic similarities between documents. We firstly represent documents within the vector space, and cluster the documents into a predefined number of clusters. The centroids of the clusters are treated as latent topics. We then represent each document as a mixture of latent topics. For evaluation purposes, we employ the active learning strategy using both our novel topic detection method and a baseline topic model (i.e., Latent Dirichlet Allocation). Results obtained demonstrate that our method is able to achieve a high sensitivity of eligible studies and a significantly reduced manual annotation cost when compared to the baseline method. This observation is consistent across two clinical and three public health reviews. The tool introduced in this work is available from https://nactem.ac.uk/pvtopic/. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

Smart light random memory sprays Retinex: a fast Retinex implementation for high-quality brightness adjustment and color correction.

PubMed

Banić, Nikola; Lončarić, Sven

2015-11-01

Removing the influence of illumination on image colors and adjusting the brightness across the scene are important image enhancement problems. This is achieved by applying adequate color constancy and brightness adjustment methods. One of the earliest models to deal with both of these problems was the Retinex theory. Some of the Retinex implementations tend to give high-quality results by performing local operations, but they are computationally relatively slow. One of the recent Retinex implementations is light random sprays Retinex (LRSR). In this paper, a new method is proposed for brightness adjustment and color correction that overcomes the main disadvantages of LRSR. There are three main contributions of this paper. First, a concept of memory sprays is proposed to reduce the number of LRSR's per-pixel operations to a constant regardless of the parameter values, thereby enabling a fast Retinex-based local image enhancement. Second, an effective remapping of image intensities is proposed that results in significantly higher quality. Third, the problem of LRSR's halo effect is significantly reduced by using an alternative illumination processing method. The proposed method enables a fast Retinex-based image enhancement by processing Retinex paths in a constant number of steps regardless of the path size. Due to the halo effect removal and remapping of the resulting intensities, the method outperforms many of the well-known image enhancement methods in terms of resulting image quality. The results are presented and discussed. It is shown that the proposed method outperforms most of the tested methods in terms of image brightness adjustment, color correction, and computational speed.

Ulinastatin Suppresses Burn-Induced Lipid Peroxidation and Reduces Fluid Requirements in a Swine Model

PubMed Central

Luo, Hong-Min; Du, Ming-Hua; Lin, Zhi-Long; Hu, Quan; Zhang, Lin; Ma, Li; Wang, Huan; Wen, Yu; Lv, Yi; Lin, Hong-Yuan; Pi, Yu-Li; Hu, Sen; Sheng, Zhi-Yong

2013-01-01

Objective. Lipid peroxidation plays a critical role in burn-induced plasma leakage, and ulinastatin has been reported to reduce lipid peroxidation in various models. This study aims to examine whether ulinastatin reduces fluid requirements through inhibition of lipid peroxidation in a swine burn model. Methods. Forty miniature swine were subjected to 40% TBSA burns and were randomly allocated to the following four groups: immediate lactated Ringer's resuscitation (ILR), immediate LR containing ulinastatin (ILR/ULI), delayed LR resuscitation (DLR), and delayed LR containing ulinastatin (DLR/ULI). Hemodynamic variables, net fluid accumulation, and plasma thiobarbituric acid reactive substances (TBARS) concentrations were measured. Heart, liver, lung, skeletal muscle, and ileum were harvested at 48 hours after burn for evaluation of TBARS concentrations, activities of antioxidant enzymes, and tissue water content. Results. Ulinastatin significantly reduced pulmonary vascular permeability index (PVPI) and extravascular lung water index (ELWI), net fluid accumulation, and water content of heart, lung, and ileum in both immediate or delayed resuscitation groups. Furthermore, ulinastatin infusion significantly reduced plasma and tissue concentrations of TBARS in both immediate or delayed resuscitation groups. Conclusions. These results indicate that ulinastatin can reduce fluid requirements through inhibition of lipid peroxidation. PMID:23738046

A methodology for probabilistic remaining creep life assessment of gas turbine components

NASA Astrophysics Data System (ADS)

Liu, Zhimin

Certain gas turbine components operate in harsh environments and various mechanisms may lead to component failure. It is common practice to use remaining life assessments to help operators schedule maintenance and component replacements. Creep is a major failure mechanisms that affect the remaining life assessment, and the resulting life consumption of a component is highly sensitive to variations in the material stresses and temperatures, which fluctuate significantly due to the changes in real operating conditions. In addition, variations in material properties and geometry will result in changes in creep life consumption rate. The traditional method used for remaining life assessment assumes a set of fixed operating conditions at all times, and it fails to capture the variations in operating conditions. This translates into a significant loss of accuracy and unnecessary high maintenance and replacement cost. A new method that captures these variations described above and improves the prediction accuracy of remaining life is developed. First, a metamodel is built to approximate the relationship between variables (operating conditions, material properties, geometry, etc.) and a creep response. The metamodel is developed using Response Surface Method/Design of Experiments methodology. Design of Experiments is an efficient sampling method, and for each sampling point a set of finite element analyses are used to compute the corresponding response value. Next, a low order polynomial Response Surface Equation (RSE) is used to fit these values. Four techniques are suggested to dramatically reduce computational effort, and to increase the accuracy of the RSE: smart meshing technique, automatic geometry parameterization, screening test and regional RSE refinement. The RSEs, along with a probabilistic method and a life fraction model are used to compute current damage accumulation and remaining life. By capturing the variations mentioned above, the new method results in much better accuracy than that available using the traditional method. After further development and proper verification the method should bring significant savings by reducing the number of inspections and deferring part replacement.

Data entry errors and design for model-based tight glycemic control in critical care.

PubMed

Ward, Logan; Steel, James; Le Compte, Aaron; Evans, Alicia; Tan, Chia-Siong; Penning, Sophie; Shaw, Geoffrey M; Desaive, Thomas; Chase, J Geoffrey

2012-01-01

Tight glycemic control (TGC) has shown benefits but has been difficult to achieve consistently. Model-based methods and computerized protocols offer the opportunity to improve TGC quality but require human data entry, particularly of blood glucose (BG) values, which can be significantly prone to error. This study presents the design and optimization of data entry methods to minimize error for a computerized and model-based TGC method prior to pilot clinical trials. To minimize data entry error, two tests were carried out to optimize a method with errors less than the 5%-plus reported in other studies. Four initial methods were tested on 40 subjects in random order, and the best two were tested more rigorously on 34 subjects. The tests measured entry speed and accuracy. Errors were reported as corrected and uncorrected errors, with the sum comprising a total error rate. The first set of tests used randomly selected values, while the second set used the same values for all subjects to allow comparisons across users and direct assessment of the magnitude of errors. These research tests were approved by the University of Canterbury Ethics Committee. The final data entry method tested reduced errors to less than 1-2%, a 60-80% reduction from reported values. The magnitude of errors was clinically significant and was typically by 10.0 mmol/liter or an order of magnitude but only for extreme values of BG < 2.0 mmol/liter or BG > 15.0-20.0 mmol/liter, both of which could be easily corrected with automated checking of extreme values for safety. The data entry method selected significantly reduced data entry errors in the limited design tests presented, and is in use on a clinical pilot TGC study. The overall approach and testing methods are easily performed and generalizable to other applications and protocols. © 2012 Diabetes Technology Society.

Risk Analysis of Earth-Rock Dam Failures Based on Fuzzy Event Tree Method

PubMed Central

Fu, Xiao; Gu, Chong-Shi; Su, Huai-Zhi; Qin, Xiang-Nan

2018-01-01

Earth-rock dams make up a large proportion of the dams in China, and their failures can induce great risks. In this paper, the risks associated with earth-rock dam failure are analyzed from two aspects: the probability of a dam failure and the resulting life loss. An event tree analysis method based on fuzzy set theory is proposed to calculate the dam failure probability. The life loss associated with dam failure is summarized and refined to be suitable for Chinese dams from previous studies. The proposed method and model are applied to one reservoir dam in Jiangxi province. Both engineering and non-engineering measures are proposed to reduce the risk. The risk analysis of the dam failure has essential significance for reducing dam failure probability and improving dam risk management level. PMID:29710824

A robust cloud registration method based on redundant data reduction using backpropagation neural network and shift window

NASA Astrophysics Data System (ADS)

Xin, Meiting; Li, Bing; Yan, Xiao; Chen, Lei; Wei, Xiang

2018-02-01

A robust coarse-to-fine registration method based on the backpropagation (BP) neural network and shift window technology is proposed in this study. Specifically, there are three steps: coarse alignment between the model data and measured data, data simplification based on the BP neural network and point reservation in the contour region of point clouds, and fine registration with the reweighted iterative closest point algorithm. In the process of rough alignment, the initial rotation matrix and the translation vector between the two datasets are obtained. After performing subsequent simplification operations, the number of points can be reduced greatly. Therefore, the time and space complexity of the accurate registration can be significantly reduced. The experimental results show that the proposed method improves the computational efficiency without loss of accuracy.

Which is the best method of sterilization of tumour bone for reimplantation? a biomechanical and histopathological study

PubMed Central

2010-01-01

Introduction Sterilization and re-usage of tumour bone for reconstruction after tumour resection is now gaining popularity in the East. This recycle tumour bone needs to be sterilized in order to eradicate the tumour cells before re-implantation for limb salvage procedures. The effect of some of these treatments on the integrity and sterility of the bone after treatment has been published but there has yet been a direct comparison between the various methods of sterilization to determine the one method that gives the best tumour kill without compromising the bone's structural integrity. Method This study was performed to evaluate the effect of several sterilization methods on the mechanical behavior of human cortical bone graft and histopathology evaluation of tumour bone samples after being processed with 4 different methods of sterilization. Fresh human cortical tumour bone is harvested from the diaphyseal region of the tumour bone were sterilized by autoclave (n =10); boiling (n =10); pasteurization (n =10); and irradiation (n =10). There were also 10 control specimens that did not receive any form of sterilization treatment. The biomechanical test conducted were stress to failure, modulus and strain to failure, which were determined from axial compression testing. Statistical analysis (ANOVA) was performed on these results. Significance level (α) and power (β) were set to 0.05 and 0.90, respectively. Results ANOVA analysis of 'failure stress', 'modulus' and 'strain to failure' demonstrated significant differences (p < 0.05) between treated cortical bone and untreated specimens under mechanical loading. 'Stress to failure' was significantly reduced in boiled, autoclaved and irradiated cortical bone samples (p < 0.05). 'Modulus' detected significant differences in the boiled, autoclaved and pasteurization specimens compared to controls (p < 0.05). 'Strain to failure' was reduced by irradiation (p < 0.05) but not by the other three methods of treatments. Histopathology study revealed no viable tumour cell in any of four types of treatment group compared to the untreated control group. Conclusions Sterilization of cortical bone sample by pasteurization and to a lesser extent, irradiation does not significantly alter the mechanical properties when compared with untreated samples. Mechanical properties degrade with the use of high temperature for sterilization (boiling). All methods of sterilization gave rise to 100 percent tumour kill. PMID:20831801

A method for the estimation of the significance of cross-correlations in unevenly sampled red-noise time series

NASA Astrophysics Data System (ADS)

Max-Moerbeck, W.; Richards, J. L.; Hovatta, T.; Pavlidou, V.; Pearson, T. J.; Readhead, A. C. S.

2014-11-01

We present a practical implementation of a Monte Carlo method to estimate the significance of cross-correlations in unevenly sampled time series of data, whose statistical properties are modelled with a simple power-law power spectral density. This implementation builds on published methods; we introduce a number of improvements in the normalization of the cross-correlation function estimate and a bootstrap method for estimating the significance of the cross-correlations. A closely related matter is the estimation of a model for the light curves, which is critical for the significance estimates. We present a graphical and quantitative demonstration that uses simulations to show how common it is to get high cross-correlations for unrelated light curves with steep power spectral densities. This demonstration highlights the dangers of interpreting them as signs of a physical connection. We show that by using interpolation and the Hanning sampling window function we are able to reduce the effects of red-noise leakage and to recover steep simple power-law power spectral densities. We also introduce the use of a Neyman construction for the estimation of the errors in the power-law index of the power spectral density. This method provides a consistent way to estimate the significance of cross-correlations in unevenly sampled time series of data.

Diagnosis of Chronic Kidney Disease Based on Support Vector Machine by Feature Selection Methods.

PubMed

Polat, Huseyin; Danaei Mehr, Homay; Cetin, Aydin

2017-04-01

As Chronic Kidney Disease progresses slowly, early detection and effective treatment are the only cure to reduce the mortality rate. Machine learning techniques are gaining significance in medical diagnosis because of their classification ability with high accuracy rates. The accuracy of classification algorithms depend on the use of correct feature selection algorithms to reduce the dimension of datasets. In this study, Support Vector Machine classification algorithm was used to diagnose Chronic Kidney Disease. To diagnose the Chronic Kidney Disease, two essential types of feature selection methods namely, wrapper and filter approaches were chosen to reduce the dimension of Chronic Kidney Disease dataset. In wrapper approach, classifier subset evaluator with greedy stepwise search engine and wrapper subset evaluator with the Best First search engine were used. In filter approach, correlation feature selection subset evaluator with greedy stepwise search engine and filtered subset evaluator with the Best First search engine were used. The results showed that the Support Vector Machine classifier by using filtered subset evaluator with the Best First search engine feature selection method has higher accuracy rate (98.5%) in the diagnosis of Chronic Kidney Disease compared to other selected methods.

Implementation of Kalman filter algorithm on models reduced using singular pertubation approximation method and its application to measurement of water level

NASA Astrophysics Data System (ADS)

Rachmawati, Vimala; Khusnul Arif, Didik; Adzkiya, Dieky

2018-03-01

The systems contained in the universe often have a large order. Thus, the mathematical model has many state variables that affect the computation time. In addition, generally not all variables are known, so estimations are needed to measure the magnitude of the system that cannot be measured directly. In this paper, we discuss the model reduction and estimation of state variables in the river system to measure the water level. The model reduction of a system is an approximation method of a system with a lower order without significant errors but has a dynamic behaviour that is similar to the original system. The Singular Perturbation Approximation method is one of the model reduction methods where all state variables of the equilibrium system are partitioned into fast and slow modes. Then, The Kalman filter algorithm is used to estimate state variables of stochastic dynamic systems where estimations are computed by predicting state variables based on system dynamics and measurement data. Kalman filters are used to estimate state variables in the original system and reduced system. Then, we compare the estimation results of the state and computational time between the original and reduced system.

The effect of different cooking methods on fatty acid composition and antioxidant activity of n-3 fatty acids fortified tilapia meat with or without clove essential oil.

PubMed

Ramezani-Fard, Ehsan; Romano, Nicholas; Goh, Yong-Meng; Oskoueian, Ehsan; Ehteshami, Fariborz; Ebrahimi, Mahdi

2016-07-01

Tilapia farmers are increasingly relying on dietary fish oil alternatives which substantially reduces health beneficial n-3 polyunsaturated fatty acids (PUFA) in tilapia products.? This may be further exacerbated depending on the cooking method.? This study aimed to evaluate the effects of different cooking methods on the fatty acid composition and oxidative stability of tilapia minced meat after prior fish oil fortifications with or without clove essential oil. Results showed that frying tilapia in either sunflower or palm oil significantly increased the saturated fatty acid and linoleic acid content, respectively, of tilapia. However, fish oil fortifications significantly increased the n-3 PUFA content, but tended to decrease oxidative stability, particularly when microwaving. This was mitigated by clove essential oil, which significantly improved oxidative stability after cooking. Results indicate that n-3 PUFA and clove essential oil fortifications is an effective method to deliver and protect these beneficial fatty acids for human consumers. ?

[The Misgav-Ladach method for cesarean section compared to the Pfannenstiel technique].

PubMed

Studziński, Zbigniew

2002-08-01

The aim of the study was to evaluate the outcome of two different methods of cesarean section. To determine whether the Misgav-Ladach caesarean technique can offer benefits when compared with conventional Pfannenstiel caesarean section technique. This study describes operative details and the postoperative course of 110 patients who underwent caesarean section in May 2000 to December 2000 in Department of Gynecology and Obstetrics in Regional Hospital in Slupsk, Poland. One group (50 women) was operated with the Misgav-Ladach method for caesarean section and the other group (60 women) with Pfannenstiel method. Operating time was significantly different between the two methods, with an average of 20.2 minutes with the Misgav-Ladach method and 47.3 minutes with the Pfannenstiel method (p < 0.001). Time of child delivery was with average 1.1 minutes with the Misgav-Ladach method and 3.8 minutes with the Pfannenstiel method (p < 0.001). The amount of blood loss different significantly, with 336 ml and 483 ml respectively (p < 0.001). No significant difference was found in Apgar scores. No difference was found in overall postoperative complications, wound infection, febrile illness, febrile morbidity, wound dehiscence affected by the new technique. Significantly less suture material was used during Misgav-Ladach caesarean section compared to Pfannenstiel technique (p < 0.001). The Misgav-Ladach method of caesarean section has advantages over the Pfannenstiel technique by being significantly quicker to perform, with the reduced amounts of bleeding and suture material. The women were satisfied with the appearance of their scars. In this study no negative effects of the new operation technique were discovered.

The effects of topical sodium cromoglicate on itch and flare in human skin induced by intradermal histamine: a randomised double-blind vehicle controlled intra-subject design trial

PubMed Central

2011-01-01

Background Itch is a prominent feature of many skin diseases, particularly atopic dermatitis and cutaneous mastocytosis. Sodium cromoglicate (SCG), a chromone developed for the treatment of allergic disease has been shown to reduce the severity of itch when applied topically to subjects with atopic dermatitis. The aim of this study was to investigate whether topical sodium cromoglicate can reduce the severity of itch induced by intradermal histamine. Methods SCG was introduced into the skin of healthy volunteers both by iontophoresis and by topical application using a new 4% cutaneous emulsion (Altoderm™). The skin was then challenged with intradermal histamine. Measurements were made of severity of itch, size of wheal and flare and change in blood flux Results SCG significantly reduced the severity of itch (P = 0.0045) and flare (P = 0.0143) when delivered by iontophoresis. SCG 4% cutaneous emulsion significantly reduced severity of itch (P = 0.024) and flare (P = 0.015) in atopic subjects. Trend analysis showed increasing effect on itch with increased concentrations of SCG, which was significant (P = 0.046). There were no effects on wheal or blood flux. Conclusions Topically applied SCG, administered in a new cutaneous emulsion base, significantly reduced the itch and flare caused by intradermal histamine. The effect was greatest in atopic subjects and increased with the concentration of SCG in the emulsion. Trial registration ISRCTN35671014 PMID:21385340

The Effect of Reflexology Applied to Patients with Chronic Obstructive Pulmonary Disease on Dyspnea and Fatigue.

PubMed

Polat, Hatice; Ergüney, Seher

The purpose of this study was to determine the effect of reflexology on reducing dyspnea and fatigue in patients with chronic obstructive pulmonary disease (COPD). The study was conducted as a pretest-posttest experimental design. The population of the study consisted of 60 patients (30 in experimental group and 30 in control group). Patient Description Form, Baseline Dyspnea Index (BDI) and Visual Analogue Scale-Fatigue (VAS-F) were used to collect the data. The difference between pretest-posttest dyspnea and fatigue mean scores of patients in the experimental group was statistically significant (p < .01). The difference between pretest-posttest dyspnea and fatigue mean scores of patients in the control group was statistically insignificant (p > .05). It was determined that the reflexology reduced dyspnea and fatigue in patients with COPD. Complementary methods such as reflexology should be used with pharmacological methods to reduce dyspnea and fatigue of COPD patients.

Propulsion integration for military aircraft

NASA Technical Reports Server (NTRS)

Henderson, William P.

1989-01-01

The transonic aerodynamic characteristics for high-performance aircraft are significantly affected by shock-induced flow interactions as well as other local flow interference effects which usually occur at transonic speeds. These adverse interactions can not only cause high drag, but can cause unusual aerodynamic loadings and/or severe stability and control problems. Many new programs are underway to develop methods for reducing the adverse effects, as well as to develop an understanding of the basic flow conditions which are the primary contributors. It is anticipated that these new programs will result in technologies which can reduce the aircraft cruise drag through improved integration as well as increased aircraft maneuverability throughh the application of thrust vectoring. This paper will identify some of the primary propulsion integration problems for high performance aircraft at transonic speeds, and demonstrate several methods for reducing or eliminating the undesirable characteristics, while enhancing configuration effectiveness.

Fast Time-Dependent Density Functional Theory Calculations of the X-ray Absorption Spectroscopy of Large Systems.

PubMed

Besley, Nicholas A

2016-10-11

The computational cost of calculations of K-edge X-ray absorption spectra using time-dependent density functional (TDDFT) within the Tamm-Dancoff approximation is significantly reduced through the introduction of a severe integral screening procedure that includes only integrals that involve the core s basis function of the absorbing atom(s) coupled with a reduced quality numerical quadrature for integrals associated with the exchange and correlation functionals. The memory required for the calculations is reduced through construction of the TDDFT matrix within the absorbing core orbitals excitation space and exploiting further truncation of the virtual orbital space. The resulting method, denoted fTDDFTs, leads to much faster calculations and makes the study of large systems tractable. The capability of the method is demonstrated through calculations of the X-ray absorption spectra at the carbon K-edge of chlorophyll a, C 60 and C 70 .

Blanking Method with Aid of Scrap to Reduce Tensile Residual Stress on Sheared Edge

NASA Astrophysics Data System (ADS)

Yasutomi, T.; Yonemura, S.; Yoshida, T.; Mizumura, M.; Hiwatashi, S.

2017-09-01

A simple shearing method to reduce tensile residual stress on a sheared edge is highly desired in the automotive industry because this type of stress deteriorates the fatigue property of automotive parts. In this study, the effect of a coining method with a shearing scrap material on a sheared edge was investigated. The scrap part of a sheared plate has a fracture surface shape similar to that of the product part since these parts are generated by separation of a single plate with crack propagation. Therefore, it is possible to impose plastic strain over the entire fracture surface by using the scrap part as a coining tool. Effectiveness of this method was investigated for high-tensile-strength steel. Using this method, the tensile residual stress on the sheared surface was significantly reduced and work hardening was slightly increased. The effects of shearing clearance and coining stroke were also investigated. Tensile residual stress decreased as the coining stroke increased; however, it saturated at a certain stroke. The stroke at which tensile residual stress saturated was relatively small at a large clearance. In particular, the amount of plastic deformation on fracture surface increased when coining stroke became large. These tendencies could be explained by the conditions of contact, which were investigated using finite element analysis.

Dynamic frame resizing with convolutional neural network for efficient video compression

NASA Astrophysics Data System (ADS)

Kim, Jaehwan; Park, Youngo; Choi, Kwang Pyo; Lee, JongSeok; Jeon, Sunyoung; Park, JeongHoon

2017-09-01

In the past, video codecs such as vc-1 and H.263 used a technique to encode reduced-resolution video and restore original resolution from the decoder for improvement of coding efficiency. The techniques of vc-1 and H.263 Annex Q are called dynamic frame resizing and reduced-resolution update mode, respectively. However, these techniques have not been widely used due to limited performance improvements that operate well only under specific conditions. In this paper, video frame resizing (reduced/restore) technique based on machine learning is proposed for improvement of coding efficiency. The proposed method features video of low resolution made by convolutional neural network (CNN) in encoder and reconstruction of original resolution using CNN in decoder. The proposed method shows improved subjective performance over all the high resolution videos which are dominantly consumed recently. In order to assess subjective quality of the proposed method, Video Multi-method Assessment Fusion (VMAF) which showed high reliability among many subjective measurement tools was used as subjective metric. Moreover, to assess general performance, diverse bitrates are tested. Experimental results showed that BD-rate based on VMAF was improved by about 51% compare to conventional HEVC. Especially, VMAF values were significantly improved in low bitrate. Also, when the method is subjectively tested, it had better subjective visual quality in similar bit rate.

Income analysis of goat farmers on the farmers group in district of Serdang Bedagai

NASA Astrophysics Data System (ADS)

Manurung, J. N.; Hasnudi; Supriana, T.

2018-02-01

The farmers group are expected to reduce the production cost of goat breeding and improve the income of farmers which impact on the welfare of goat farmers. This research aim to analyze the factors that influence the income of farmers group, in sub-district Dolok Masihul Pegajahan, and Dolok Merawan, Serdang Bedagai. The method used is survey method with 90 respondents. Data was analysed by multiple linear regression. The result showed, simultaneously goat cost, sale price of goat, fixed cost and variable cost had significant effect on income of goat farmers. Partially, goat cost, variable cost and sale price of goat had significant effect on income of goat farmers, while fixed cost had no significant effect.

Test Results for Entry Guidance Methods for Space Vehicles

NASA Technical Reports Server (NTRS)

Hanson, John M.; Jones, Robert E.

2004-01-01

There are a number of approaches to advanced guidance and control that have the potential for achieving the goals of significantly increasing reusable launch vehicle (or any space vehicle that enters an atmosphere) safety and reliability, and reducing the cost. This paper examines some approaches to entry guidance. An effort called Integration and Testing of Advanced Guidance and Control Technologies has recently completed a rigorous testing phase where these algorithms faced high-fidelity vehicle models and were required to perform a variety of representative tests. The algorithm developers spent substantial effort improving the algorithm performance in the testing. This paper lists the test cases used to demonstrate that the desired results are achieved, shows an automated test scoring method that greatly reduces the evaluation effort required, and displays results of the tests. Results show a significant improvement over previous guidance approaches. The two best-scoring algorithm approaches show roughly equivalent results and are ready to be applied to future vehicle concepts.

Test Results for Entry Guidance Methods for Reusable Launch Vehicles

NASA Technical Reports Server (NTRS)

Hanson, John M.; Jones, Robert E.

2003-01-01

There are a number of approaches to advanced guidance and control (AG&C) that have the potential for achieving the goals of significantly increasing reusable launch vehicle (RLV) safety and reliability, and reducing the cost. This paper examines some approaches to entry guidance. An effort called Integration and Testing of Advanced Guidance and Control Technologies (ITAGCT) has recently completed a rigorous testing phase where these algorithms faced high-fidelity vehicle models and were required to perform a variety of representative tests. The algorithm developers spent substantial effort improving the algorithm performance in the testing. This paper lists the test cases used to demonstrate that the desired results are achieved, shows an automated test scoring method that greatly reduces the evaluation effort required, and displays results of the tests. Results show a significant improvement over previous guidance approaches. The two best-scoring algorithm approaches show roughly equivalent results and are ready to be applied to future reusable vehicle concepts.

Phenolic content and antioxidant activity of Pereskia grandifolia Haw. (Cactaceae) extracts

PubMed Central

Sim, K. S.; Nurestri, A. M. Sri; Norhanom, A. W.

2010-01-01

The leaves of Pereskia grandifolia Haw. (Cactaceae), commonly known as “Jarum Tujuh Bilah” in Malaysia, have been traditionally used as natural remedy in folk medicine by the locals. In the present study, the antioxidant potential of P. grandifolia crude methanol and its fractionated extracts (hexane, ethyl acetate and water) have been investigated, employing three different established testing systems, such as scavenging activity on 1,1-diphenyl-2-picrylhydrazyl (DPPH) radicals, reducing power assay and β-carotene method. The total phenolic content of the P. grandifolia extracts was also assessed by the Folin-Ciocalteau’s method. The ethyl acetate extract showed significantly the highest total phenolic content, DPPH scavenging ability and antioxidant activity in β-carotene bleaching assay while the hexane extract possessed significantly strongest reducing power. The data obtained in these testing systems clearly establish the antioxidant potency of P. grandifolia. As such, this is the first report on the antioxidant activities of P. grandifolia. PMID:20931088

Fitting of hearing aids with different technical parameters to a patient with dead regions

NASA Astrophysics Data System (ADS)

Hojan-Jezierska, Dorota; Skrodzka, Ewa

2009-01-01

The purpose of the study was to determine an optimal hearing aid fitting procedure for a patient with well diagnosed high-frequency ‘dead regions’ in both cochleas. The patient reported non-symmetrical hearing problems of sensorineural origin. For binaural amplification two similar independent hearing aids were used as well as a pair of dependent devices with an ear-to-ear function. Two fitting methods were used: DSLi/o and NAL-NL1, and four different strategies of fitting were tested: the initial fitting based on the DSLi/o or NAL-NL1 method with necessary loudness corrections, the second fitting taking into account all the available functions of hearing instruments, the third fitting (based on the second one) but with significantly reduced amplification well above one octave of frequency inside dead region, and the final fitting with significantly reduced gain slightly below one octave inside dead regions. The results of hearing aids fitting were assessed using an APHAB procedure.

[Curative effect of ozone hydrotherapy for pemphigus].

PubMed

Jiang, Fuqiong; Deng, Danqi; Li, Xiaolan; Wang, Wenfang; Xie, Hong; Wu, Yongzhuo; Luan, Chunyan; Yang, Binbin

2018-02-28

To determine clinical curative effects of ozone therapy for pemphigus vulgaris.
 Methods: Ozone hydrotherapy was used as an aid treatment for 32 patients with pemphigus vulgaris. The hydropathic compression of potassium permanganate solution for 34 patients with pemphigus vulgaris served as a control. The main treatment for both groups were glucocorticoids and immune inhibitors. The lesions of patients, bacterial infection, usage of antibiotics, patient's satisfaction, and clinical curative effect were evaluated in the 2 groups.
 Results: There was no significant difference in the curative effect and the average length of staying at hospital between the 2 groups (P>0.05). But rate for the usage of antibiotics was significantly reduced in the group of ozone hydrotherapy (P=0.039). The patients were more satisfied in using ozone hydrotherapy than the potassium permanganate solution after 7-day therapy (P>0.05).
 Conclusion: Ozone hydrotherapy is a safe and effective aid method for pemphigus vulgaris. It can reduce the usage of antibiotics.

Symboldrama, a psychotherapeutic method for adolescents with dissociative and PTSD symptoms: a pilot study.

PubMed

Nilsson, Doris; Wadsby, Marie

2010-01-01

A total of 15 clinically referred adolescents who had been sexually or physically abused participated in this pilot study of the use of symboldrama psychotherapy. Symboldrama is a psychotherapeutic method that uses imagery as the major psychotherapeutic tool. All adolescents reported to be suffering from a high level of dissociative symptoms and other symptoms such as anxiety, depression, posttraumatic stress, and anger after their traumas. The objective of the study was to test the hypothesis that symboldrama psychotherapy in addition to psycho-education of the non-offending parent would significantly reduce the reported symptoms. Before treatment, the participants answered three questionnaires: (a) the Life Incidence of Traumatic Events Scale, (b) the Trauma Symptom Checklist for Children, and (c) the Dissociation Questionnaire-Swedish version. After treatment, the participants once again filled out the Trauma Symptom Checklist for Children and the Dissociation Questionnaire-Swedish version. The scores from before and after treatment were compared, and the results showed that the symptoms had been statistically significantly reduced.

Significant improvement in the thermal annealing process of optical resonators

NASA Astrophysics Data System (ADS)

Salzenstein, Patrice; Zarubin, Mikhail

2017-05-01

Thermal annealing performed during process improves the quality of the roughness of optical resonators reducing stresses at the periphery of their surface thus allowing higher Q-factors. After a preliminary realization, the design of the oven and the electronic method were significantly improved thanks to nichrome resistant alloy wires and chopped basalt fibers for thermal isolation during the annealing process. Q-factors can then be improved.

Advances in environmental and occupational respiratory diseases in 2009.

PubMed

Peden, David B; Bush, Robert K

2010-03-01

The year 2009 led to a number of significant advances in environmental and occupational allergic diseases. The role of exposure to environmental pollutants, respiratory viruses, and allergen exposure showed significant advances. New allergens were identified. Occupational asthma and the relationship of complementary and alternative medicine to allergic diseases were extensively reviewed. New approaches to immunotherapy, novel vaccine techniques, and methods to reduce risks for severe allergic disease were addressed.

Microwave-assisted Derivatization of Fatty Acids for Its Measurement in Milk Using High-Performance Liquid Chromatography.

PubMed

Shrestha, Rojeet; Miura, Yusuke; Hirano, Ken-Ichi; Chen, Zhen; Okabe, Hiroaki; Chiba, Hitoshi; Hui, Shu-Ping

2018-01-01

Fatty acid (FA) profiling of milk has important applications in human health and nutrition. Conventional methods for the saponification and derivatization of FA are time-consuming and laborious. We aimed to develop a simple, rapid, and economical method for the determination of FA in milk. We applied a beneficial approach of microwave-assisted saponification (MAS) of milk fats and microwave-assisted derivatization (MAD) of FA to its hydrazides, integrated with HPLC-based analysis. The optimal conditions for MAS and MAD were determined. Microwave irradiation significantly reduced the sample preparation time from 80 min in the conventional method to less than 3 min. We used three internal standards for the measurement of short-, medium- and long-chain FA. The proposed method showed satisfactory analytical sensitivity, recovery and reproducibility. There was a significant correlation in the milk FA concentrations between the proposed and conventional methods. Being quick, economic, and convenient, the proposed method for the milk FA measurement can be substitute for the convention method.

A Simple and Efficient Method of Extracting DNA from Aged Bones and Teeth.

PubMed

Liu, Qiqi; Liu, Liyan; Zhang, Minli; Zhang, Qingzhen; Wang, Qiong; Ding, Xiaoran; Shao, Liting; Zhou, Zhe; Wang, Shengqi

2018-05-01

DNA is often difficult to extract from old bones and teeth due to low levels of DNA and high levels of degradation. This study established a simple yet efficient method for extracting DNA from 20 aged bones and teeth (approximately 60 years old). Based on the concentration and STR typing results, the new method of DNA extraction (OM) developed in this study was compared with the PrepFiler™ BTA Forensic DNA Extraction Kit (BM). The total amount of DNA extracted using the OM method was not significantly different from that extracted using the commercial kit (p > 0.05). However, the number of STR loci detected was significantly higher in the samples processed using the OM method than using the BM method (p < 0.05). This study aimed to establish a DNA extraction method for aged bones and teeth to improve the detection rate of STR typing and reduce costs compared to the BM technique. © 2017 American Academy of Forensic Sciences.

Femtosecond laser surface texturing of titanium as a method to reduce the adhesion of Staphylococcus aureus and biofilm formation

NASA Astrophysics Data System (ADS)

Cunha, Alexandre; Elie, Anne-Marie; Plawinski, Laurent; Serro, Ana Paula; Botelho do Rego, Ana Maria; Almeida, Amélia; Urdaci, Maria C.; Durrieu, Marie-Christine; Vilar, Rui

2016-01-01

The aim of the present work was to investigate the possibility of using femtosecond laser surface texturing as a method to reduce the colonization of Grade 2 Titanium alloy surfaces by Staphylococcus aureus and the subsequent formation of biofilm. The laser treatments were carried out with a Yb:KYW chirped-pulse-regenerative amplification laser system with a central wavelength of 1030 nm and a pulse duration of 500 fs. Two types of surface textures, consisting of laser-induced periodic surface structures (LIPSS) and nanopillars, were produced. The topography, chemical composition and phase constitution of these surfaces were investigated by atomic force microscopy, scanning electron microscopy, X-ray photoelectron spectroscopy, micro-Raman spectroscopy, and X-ray diffraction. Surface wettability was assessed by the sessile drop method using water and diiodomethane as testing liquids. The response of S. aureus put into contact with the laser treated surfaces in controlled conditions was investigated by epifluorescence microscopy and scanning electron microscopy 48 h after cell seeding. The results achieved show that the laser treatment reduces significantly the bacterial adhesion to the surface as well as biofilm formation as compared to a reference polished surfaces and suggest that femtosecond laser texturing is a simple and promising method for endowing dental and orthopedic titanium implants with antibacterial properties, reducing the risk of implant-associated infections without requiring immobilized antibacterial substances, nanoparticles or coatings.

Effect of different processing methods on antioxidant activity of underutilized legumes, Entada scandens seed kernel and Canavalia gladiata seeds.

PubMed

Sasipriya, Gopalakrishnan; Siddhuraju, Perumal

2012-08-01

The present study is proposed to determine the antioxidant activity of raw and processed samples of underutilized legumes, Entada scandens seed kernel and Canavalia gladiata seeds. The indigenous processing methods like dry heating, autoclaving and soaking followed by autoclaving in different solutions (plain water, ash, sugar and sodium bicarbonate) were adopted to seed samples. All other processing methods than dry heat showed significant reduction in phenolics (2.9-63%), tannins (26-100%) and flavonoids (14-67%). However, in processed samples of E. scandens, the hydroxyl radical scavenging activity and β-carotene bleaching inhibition activity were increased, whereas, 2,2-azinobis (3-ethyl benzothiazoline-6-sulfonic acid) diammonium salt (ABTS·(+)), ferric reducing antioxidant power (FRAP), metal chelating and superoxide anion scavenging activity were similar to unprocessed ones. In contrary, except dry heating in C. gladiata, all other processing methods significantly (P<0.05) reduced the 2,2'-diphenyl-1-picryl-hydrazyl (DPPH·) (20-35%), ABTS·(+) (22-75%), FRAP (34-74%), metal chelating (30-41%), superoxide anion radical scavenging (8-80%), hydroxyl radical scavenging (20-40%) and β-carotene bleaching inhibition activity (15-69%). In addition, the sample extracts of raw and dry heated samples protected DNA damage at 10 μg. All processing methods in E. scandens and dry heating in C. gladiata would be a suitable method for adopting in domestic or industrial processing. Copyright © 2012 Elsevier Ltd. All rights reserved.

Application of Absorbable Hemostatic Materials Observed in Thyroid Operation

NASA Astrophysics Data System (ADS)

Li, Yan-Ming; Liang, Zhen-Zhen; Song, Yan

2016-05-01

To observe the application effects of the absorbable hemostatic materials in thyroid operation. Methods: From May 2014 to January 2015, 100 patients with thyroid surgery in our university affiliated hospital were selected as the research object. Randomly divided into experimental group and control group, 50 cases in each group. Application of absorbable hemostatic hemostatic materials in the experimental group during the operation, the control group using the traditional mechanical methods of hemostasis hemostasis to observe the operation time, bleeding volume, postoperative drainage volume, complications and hospital stay of the two groups. Results: The operation time, bleeding volume, postoperative drainage and hospital stay in the experimental group were significantly lower in the study group than in the control group, and the difference between the two groups was statistically significant (P< 0.05); The satisfaction of patients in the experimental group was significantly higher than that in the control group, the difference was statistically significant in the two groups (P < 0.05); There was no significant difference in the incidence of wound bleeding complications between the study group and the control group (P > 0.05). Conclusion: Absorbable hemostatic materials can effectively shorten the operation time, reduce intraoperative blood loss and postoperative drainage, reduce the length of hospital stay and improve the success rate of surgery and patient satisfaction, which is worthy to be popularized in clinical thyroid surgery.

A method to determine the impact of reduced visual function on nodule detection performance.

PubMed

Thompson, J D; Lança, C; Lança, L; Hogg, P

2017-02-01

In this study we aim to validate a method to assess the impact of reduced visual function and observer performance concurrently with a nodule detection task. Three consultant radiologists completed a nodule detection task under three conditions: without visual defocus (0.00 Dioptres; D), and with two different magnitudes of visual defocus (-1.00 D and -2.00 D). Defocus was applied with lenses and visual function was assessed prior to each image evaluation. Observers evaluated the same cases on each occasion; this comprised of 50 abnormal cases containing 1-4 simulated nodules (5, 8, 10 and 12 mm spherical diameter, 100 HU) placed within a phantom, and 25 normal cases (images containing no nodules). Data was collected under the free-response paradigm and analysed using Rjafroc. A difference in nodule detection performance would be considered significant at p < 0.05. All observers had acceptable visual function prior to beginning the nodule detection task. Visual acuity was reduced to an unacceptable level for two observers when defocussed to -1.00 D and for one observer when defocussed to -2.00 D. Stereoacuity was unacceptable for one observer when defocussed to -2.00 D. Despite unsatisfactory visual function in the presence of defocus we were unable to find a statistically significant difference in nodule detection performance (F(2,4) = 3.55, p = 0.130). A method to assess visual function and observer performance is proposed. In this pilot evaluation we were unable to detect any difference in nodule detection performance when using lenses to reduce visual function. Copyright © 2016 The College of Radiographers. Published by Elsevier Ltd. All rights reserved.

Effects of aeration method and aeration rate on greenhouse gas emissions during composting of pig feces in pilot scale.

PubMed

Jiang, Tao; Li, Guoxue; Tang, Qiong; Ma, Xuguang; Wang, Gang; Schuchardt, Frank

2015-05-01

The aim of this study was to uncover ways to mitigate greenhouse gas (GHG) emissions and reduce energy consumption during the composting process. We assessed the effects of different aeration rates (0, 0.18, 0.36, and 0.54 L/(kg dry matter (dm)·min)) and methods (continuous and intermittent) on GHG emissions. Pig feces and corn stalks were mixed at a ratio of 7:1. The composting process lasted for 10 weeks, and the compost was turned approximately every 2 weeks. Results showed that both aeration rate and method significantly affected GHG emissions. Higher aeration rates increased NH3 and N2O losses, but reduced CH4 emissions. The exception is that the CH4 emission of the passive aeration treatment was lower than that of the low aeration rate treatment. Without forced aeration, the CH4 diffusion rates in the center of the piles were very low and part of the CH4 was oxidized in the surface layer. Intermittent aeration reduced NH3 and CH4 losses, but significantly increased N2O production during the maturing periods. Intermittent aeration increased the nitrification/denitrification alternation and thus enhanced the N2O production. Forced aeration treatments had higher GHG emission rates than the passive aeration treatment. Forced aeration accelerated the maturing process, but could not improve the quality of the end product. Compared with continuous aeration, intermittent aeration could increase the O2 supply efficiency and reduced the total GHG emission by 17.8%, and this reduction increased to 47.4% when composting was ended after 36 days. Copyright © 2015. Published by Elsevier B.V.

A scalable and accurate method for classifying protein-ligand binding geometries using a MapReduce approach.

PubMed

Estrada, T; Zhang, B; Cicotti, P; Armen, R S; Taufer, M

2012-07-01

We present a scalable and accurate method for classifying protein-ligand binding geometries in molecular docking. Our method is a three-step process: the first step encodes the geometry of a three-dimensional (3D) ligand conformation into a single 3D point in the space; the second step builds an octree by assigning an octant identifier to every single point in the space under consideration; and the third step performs an octree-based clustering on the reduced conformation space and identifies the most dense octant. We adapt our method for MapReduce and implement it in Hadoop. The load-balancing, fault-tolerance, and scalability in MapReduce allow screening of very large conformation spaces not approachable with traditional clustering methods. We analyze results for docking trials for 23 protein-ligand complexes for HIV protease, 21 protein-ligand complexes for Trypsin, and 12 protein-ligand complexes for P38alpha kinase. We also analyze cross docking trials for 24 ligands, each docking into 24 protein conformations of the HIV protease, and receptor ensemble docking trials for 24 ligands, each docking in a pool of HIV protease receptors. Our method demonstrates significant improvement over energy-only scoring for the accurate identification of native ligand geometries in all these docking assessments. The advantages of our clustering approach make it attractive for complex applications in real-world drug design efforts. We demonstrate that our method is particularly useful for clustering docking results using a minimal ensemble of representative protein conformational states (receptor ensemble docking), which is now a common strategy to address protein flexibility in molecular docking. Copyright © 2012 Elsevier Ltd. All rights reserved.

Nutrient Runoff Losses from Liquid Dairy Manure Applied with Low-Disturbance Methods.

PubMed

Jokela, William; Sherman, Jessica; Cavadini, Jason

2016-09-01

Manure applied to cropland is a source of phosphorus (P) and nitrogen (N) in surface runoff and can contribute to impairment of surface waters. Tillage immediately after application incorporates manure into the soil, which may reduce nutrient loss in runoff as well as N loss via NH volatilization. However, tillage also incorporates crop residue, which reduces surface cover and may increase erosion potential. We applied liquid dairy manure in a silage corn ( L.)-cereal rye ( L.) cover crop system in late October using methods designed to incorporate manure with minimal soil and residue disturbance. These include strip-till injection and tine aerator-band manure application, which were compared with standard broadcast application, either incorporated with a disk or left on the surface. Runoff was generated with a portable rainfall simulator (42 mm h for 30 min) three separate times: (i) 2 to 5 d after the October manure application, (ii) in early spring, and (iii) after tillage and planting. In the postmanure application runoff, the highest losses of total P and dissolved reactive P were from surface-applied manure. Dissolved P loss was reduced 98% by strip-till injection; this result was not statistically different from the no-manure control. Reductions from the aerator band method and disk incorporation were 53 and 80%, respectively. Total P losses followed a similar pattern, with 87% reduction from injected manure. Runoff losses of N had generally similar patterns to those of P. Losses of P and N were, in most cases, lower in the spring rain simulations with fewer significant treatment effects. Overall, results show that low-disturbance manure application methods can significantly reduce nutrient runoff losses compared with surface application while maintaining residue cover better than incorporation by tillage. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Reducing 4D CT artifacts using optimized sorting based on anatomic similarity.

PubMed

Johnston, Eric; Diehn, Maximilian; Murphy, James D; Loo, Billy W; Maxim, Peter G

2011-05-01

Four-dimensional (4D) computed tomography (CT) has been widely used as a tool to characterize respiratory motion in radiotherapy. The two most commonly used 4D CT algorithms sort images by the associated respiratory phase or displacement into a predefined number of bins, and are prone to image artifacts at transitions between bed positions. The purpose of this work is to demonstrate a method of reducing motion artifacts in 4D CT by incorporating anatomic similarity into phase or displacement based sorting protocols. Ten patient datasets were retrospectively sorted using both the displacement and phase based sorting algorithms. Conventional sorting methods allow selection of only the nearest-neighbor image in time or displacement within each bin. In our method, for each bed position either the displacement or the phase defines the center of a bin range about which several candidate images are selected. The two dimensional correlation coefficients between slices bordering the interface between adjacent couch positions are then calculated for all candidate pairings. Two slices have a high correlation if they are anatomically similar. Candidates from each bin are then selected to maximize the slice correlation over the entire data set using the Dijkstra's shortest path algorithm. To assess the reduction of artifacts, two thoracic radiation oncologists independently compared the resorted 4D datasets pairwise with conventionally sorted datasets, blinded to the sorting method, to choose which had the least motion artifacts. Agreement between reviewers was evaluated using the weighted kappa score. Anatomically based image selection resulted in 4D CT datasets with significantly reduced motion artifacts with both displacement (P = 0.0063) and phase sorting (P = 0.00022). There was good agreement between the two reviewers, with complete agreement 34 times and complete disagreement 6 times. Optimized sorting using anatomic similarity significantly reduces 4D CT motion artifacts compared to conventional phase or displacement based sorting. This improved sorting algorithm is a straightforward extension of the two most common 4D CT sorting algorithms.

Reducing the Take-Home Pathway of Pesticide Exposure: Behavioral Outcomes from the ¡Para Niños Saludables! Study

PubMed Central

Strong, Larkin L.; Thompson, Beti; Koepsell, Thomas D.; Meischke, Hendrika; Coronado, Gloria D.

2011-01-01

Objective To evaluate the effectiveness of a community intervention in promoting adoption of behaviors to reduce the take-home pathway of pesticide exposure in farmworker households. Methods Using two cross-sectional samples of farmworker households in 11 intervention and 12 comparison communities in Washington State, we examined whether differences over time in reported pesticide safety practices varied by community intervention status. Results Pesticide safety practices increased in both intervention and comparison communities over time. Changes were significantly greater in intervention communities for removing work shoes before entering the home (p=0.003) and marginally significantly greater for changing out of work clothes within one hour of arriving home (p=0.05). Conclusions The intervention was associated with modest effects in certain behaviors among farmworkers. Further research is needed to identify successful strategies for reducing the take-home pathway of pesticide exposure. PMID:19620892

Impacts of regulated competition on pricing in Chinese pharmaceutical market under urban employee basic medical insurance.

PubMed

Zhao, Mingyue; Wu, Jing

2017-06-01

Examine the effects of regulated competition on the drug pricing in China. Based on product-level data, a regression method was employed for pricing by using data from Tianjin Urban Employee Basic Medical Insurance (UEBMI) database. The market competition measures distinguished generic competition within the same molecule from therapeutic competition within the same therapeutic class. The increases in pricing are inversely related to the number of generic competitions. The generic sub-group results vary from the originator sub-group. For the generics, generic competition has a significantly reduced effect on the price; however, only therapeutic competition has a significantly reduced effect on the originator price. Regulated competition has a positive role in shaping the pharmaceutical market. Furthermore, regulated competition affects the price differently for the sub-groups. The promotion of competition between generic and originator in order to reap full competition benefit and reduce frictions among policies are necessary.

A new linear least squares method for T1 estimation from SPGR signals with multiple TRs

NASA Astrophysics Data System (ADS)

Chang, Lin-Ching; Koay, Cheng Guan; Basser, Peter J.; Pierpaoli, Carlo

2009-02-01

The longitudinal relaxation time, T1, can be estimated from two or more spoiled gradient recalled echo x (SPGR) images with two or more flip angles and one or more repetition times (TRs). The function relating signal intensity and the parameters are nonlinear; T1 maps can be computed from SPGR signals using nonlinear least squares regression. A widely-used linear method transforms the nonlinear model by assuming a fixed TR in SPGR images. This constraint is not desirable since multiple TRs are a clinically practical way to reduce the total acquisition time, to satisfy the required resolution, and/or to combine SPGR data acquired at different times. A new linear least squares method is proposed using the first order Taylor expansion. Monte Carlo simulations of SPGR experiments are used to evaluate the accuracy and precision of the estimated T1 from the proposed linear and the nonlinear methods. We show that the new linear least squares method provides T1 estimates comparable in both precision and accuracy to those from the nonlinear method, allowing multiple TRs and reducing computation time significantly.

Scatter measurement and correction method for cone-beam CT based on single grating scan

NASA Astrophysics Data System (ADS)

Huang, Kuidong; Shi, Wenlong; Wang, Xinyu; Dong, Yin; Chang, Taoqi; Zhang, Hua; Zhang, Dinghua

2017-06-01

In cone-beam computed tomography (CBCT) systems based on flat-panel detector imaging, the presence of scatter significantly reduces the quality of slices. Based on the concept of collimation, this paper presents a scatter measurement and correction method based on single grating scan. First, according to the characteristics of CBCT imaging, the scan method using single grating and the design requirements of the grating are analyzed and figured out. Second, by analyzing the composition of object projection images and object-and-grating projection images, the processing method for the scatter image at single projection angle is proposed. In addition, to avoid additional scan, this paper proposes an angle interpolation method of scatter images to reduce scan cost. Finally, the experimental results show that the scatter images obtained by this method are accurate and reliable, and the effect of scatter correction is obvious. When the additional object-and-grating projection images are collected and interpolated at intervals of 30 deg, the scatter correction error of slices can still be controlled within 3%.

Information Theory for Gabor Feature Selection for Face Recognition

NASA Astrophysics Data System (ADS)

Shen, Linlin; Bai, Li

2006-12-01

A discriminative and robust feature—kernel enhanced informative Gabor feature—is proposed in this paper for face recognition. Mutual information is applied to select a set of informative and nonredundant Gabor features, which are then further enhanced by kernel methods for recognition. Compared with one of the top performing methods in the 2004 Face Verification Competition (FVC2004), our methods demonstrate a clear advantage over existing methods in accuracy, computation efficiency, and memory cost. The proposed method has been fully tested on the FERET database using the FERET evaluation protocol. Significant improvements on three of the test data sets are observed. Compared with the classical Gabor wavelet-based approaches using a huge number of features, our method requires less than 4 milliseconds to retrieve a few hundreds of features. Due to the substantially reduced feature dimension, only 4 seconds are required to recognize 200 face images. The paper also unified different Gabor filter definitions and proposed a training sample generation algorithm to reduce the effects caused by unbalanced number of samples available in different classes.

a Landmark Extraction Method Associated with Geometric Features and Location Distribution

NASA Astrophysics Data System (ADS)

Zhang, W.; Li, J.; Wang, Y.; Xiao, Y.; Liu, P.; Zhang, S.

2018-04-01

Landmark plays an important role in spatial cognition and spatial knowledge organization. Significance measuring model is the main method of landmark extraction. It is difficult to take account of the spatial distribution pattern of landmarks because that the significance of landmark is built in one-dimensional space. In this paper, we start with the geometric features of the ground object, an extraction method based on the target height, target gap and field of view is proposed. According to the influence region of Voronoi Diagram, the description of target gap is established to the geometric representation of the distribution of adjacent targets. Then, segmentation process of the visual domain of Voronoi K order adjacent is given to set up target view under the multi view; finally, through three kinds of weighted geometric features, the landmarks are identified. Comparative experiments show that this method has a certain coincidence degree with the results of traditional significance measuring model, which verifies the effectiveness and reliability of the method and reduces the complexity of landmark extraction process without losing the reference value of landmark.

3-D localization of virtual sound sources: effects of visual environment, pointing method, and training.

PubMed

Majdak, Piotr; Goupell, Matthew J; Laback, Bernhard

2010-02-01

The ability to localize sound sources in three-dimensional space was tested in humans. In Experiment 1, naive subjects listened to noises filtered with subject-specific head-related transfer functions. The tested conditions included the pointing method (head or manual pointing) and the visual environment (VE; darkness or virtual VE). The localization performance was not significantly different between the pointing methods. The virtual VE significantly improved the horizontal precision and reduced the number of front-back confusions. These results show the benefit of using a virtual VE in sound localization tasks. In Experiment 2, subjects were provided with sound localization training. Over the course of training, the performance improved for all subjects, with the largest improvements occurring during the first 400 trials. The improvements beyond the first 400 trials were smaller. After the training, there was still no significant effect of pointing method, showing that the choice of either head- or manual-pointing method plays a minor role in sound localization performance. The results of Experiment 2 reinforce the importance of perceptual training for at least 400 trials in sound localization studies.

Fast online generalized multiscale finite element method using constraint energy minimization

NASA Astrophysics Data System (ADS)

Chung, Eric T.; Efendiev, Yalchin; Leung, Wing Tat

2018-02-01

Local multiscale methods often construct multiscale basis functions in the offline stage without taking into account input parameters, such as source terms, boundary conditions, and so on. These basis functions are then used in the online stage with a specific input parameter to solve the global problem at a reduced computational cost. Recently, online approaches have been introduced, where multiscale basis functions are adaptively constructed in some regions to reduce the error significantly. In multiscale methods, it is desired to have only 1-2 iterations to reduce the error to a desired threshold. Using Generalized Multiscale Finite Element Framework [10], it was shown that by choosing sufficient number of offline basis functions, the error reduction can be made independent of physical parameters, such as scales and contrast. In this paper, our goal is to improve this. Using our recently proposed approach [4] and special online basis construction in oversampled regions, we show that the error reduction can be made sufficiently large by appropriately selecting oversampling regions. Our numerical results show that one can achieve a three order of magnitude error reduction, which is better than our previous methods. We also develop an adaptive algorithm and enrich in selected regions with large residuals. In our adaptive method, we show that the convergence rate can be determined by a user-defined parameter and we confirm this by numerical simulations. The analysis of the method is presented.

Biogenic amine profile in unripe Arabica coffee beans processed according to dry and wet methods.

PubMed

Dias, Eduardo C; Pereira, Rosemary G F A; Borém, Flávio M; Mendes, Eulália; de Lima, Renato R; Fernandes, José O; Casal, Susana

2012-04-25

Immature coffee fruit processing contributes to a high amount of defective beans, which determines a significant amount of low-quality coffee sold in the Brazilian internal market. Unripe bean processing was tested, taking the levels of bioactive amines as criteria for evaluating the extent of fermentation and establishing the differences between processing methods. The beans were processed by the dry method after being mechanically depulped immediately after harvest or after a 12 h resting period in a dry pile or immersed in water. Seven bioactive amines were quantified: putrescine, spermine, spermidine, serotonin, cadaverine, histamine, and tyramine, with global amounts ranging from 71.8 to 80.3 mg/kg. The levels of spermine and spermidine were lower in the unripe depulped coffee than in the natural coffee. The specific conditions of dry and wet processing also influenced cadaverine levels, and histamine was reduced in unripe depulped coffee. A resting period of 12 h does not induce significant alteration on the beans and can be improved if performed in water. These results confirm that peeling immature coffee can decrease fermentation processes while providing more uniform drying, thus reducing the number of defects and potentially increasing beverage quality.

Intelligent single switch wheelchair navigation.

PubMed

Ka, Hyun W; Simpson, Richard; Chung, Younghyun

2012-11-01

We have developed an intelligent single switch scanning interface and wheelchair navigation assistance system, called intelligent single switch wheelchair navigation (ISSWN), to improve driving safety, comfort and efficiency for individuals who rely on single switch scanning as a control method. ISSWN combines a standard powered wheelchair with a laser rangefinder, a single switch scanning interface and a computer. It provides the user with context sensitive and task specific scanning options that reduce driving effort based on an interpretation of sensor data together with user input. Trials performed by 9 able-bodied participants showed that the system significantly improved driving safety and efficiency in a navigation task by significantly reducing the number of switch presses to 43.5% of traditional single switch wheelchair navigation (p < 0.001). All participants made a significant improvement (39.1%; p < 0.001) in completion time after only two trials.

Psychophysics of reading. XVII. Low-vision performance with four types of electronically magnified text.

PubMed

Harland, S; Legge, G E; Luebker, A

1998-03-01

Most people with low vision need magnification to read. Page navigation is the process of moving a magnifier during reading. Modern electronic technology can provide many alternatives for navigating through text. This study compared reading speeds for four methods of displaying text. The four methods varied in their page-navigation demands. The closed-circuit television (CCTV) and MOUSE methods involved manual navigation. The DRIFT method (horizontally drifting text) involved no manual navigation, but did involve both smooth-pursuit and saccadic eye movements. The rapid serial visual presentation (RSVP) method involved no manual navigation, and relatively few eye movements. There were 7 normal subjects and 12 low-vision subjects (7 with central-field loss, CFL group, and 5 with central fields intact, CFI group). The subjects read 70-word passages at speeds that yielded good comprehension. Taking the CCTV reading speed as a benchmark, neither the normal nor low-vision subjects had significantly different speeds with the MOUSE method. As expected from the reduced navigational demands, normal subjects read faster with the DRIFT method (85% faster) and the RSVP method (169%). The CFI group read significantly faster with DRIFT (43%) and RSVP (38%). The CFL group showed no significant differences in reading speed for the four methods.

Pyrolytic graphite collector development program

NASA Technical Reports Server (NTRS)

Wilkins, W. J.

1982-01-01

Pyrolytic graphite promises to have significant advantages as a material for multistage depressed collector electrodes. Among these advantages are lighter weight, improved mechanical stiffness under shock and vibration, reduced secondary electron back-streaming for higher efficiency, and reduced outgassing at higher operating temperatures. The essential properties of pyrolytic graphite and the necessary design criteria are discussed. This includes the study of suitable electrode geometries and methods of attachment to other metal and ceramic collector components consistent with typical electrical, thermal, and mechanical requirements.

Thick film magnetic nanoparticulate composites and method of manufacture thereof

NASA Technical Reports Server (NTRS)

Ge, Shihui (Inventor); Yan, Dajing (Inventor); Xiao, Danny T. (Inventor); Ma, Xinqing (Inventor); Zhang, Yide (Inventor); Zhang, Zongtao (Inventor)

2009-01-01

Thick film magnetic/insulating nanocomposite materials, with significantly reduced core loss, and their manufacture are described. The insulator coated magnetic nanocomposite comprises one or more magnetic components, and an insulating component. The magnetic component comprises nanometer scale particles (about 1 to about 100 nanometers) coated by a thin-layered insulating phase. While the intergrain interaction between the immediate neighboring magnetic nanoparticles separated by the insulating phase provides the desired soft magnetic properties, the insulating material provides high resistivity, which reduces eddy current loss.

Human Body 3D Posture Estimation Using Significant Points and Two Cameras

PubMed Central

Juang, Chia-Feng; Chen, Teng-Chang; Du, Wei-Chin

2014-01-01

This paper proposes a three-dimensional (3D) human posture estimation system that locates 3D significant body points based on 2D body contours extracted from two cameras without using any depth sensors. The 3D significant body points that are located by this system include the head, the center of the body, the tips of the feet, the tips of the hands, the elbows, and the knees. First, a linear support vector machine- (SVM-) based segmentation method is proposed to distinguish the human body from the background in red, green, and blue (RGB) color space. The SVM-based segmentation method uses not only normalized color differences but also included angle between pixels in the current frame and the background in order to reduce shadow influence. After segmentation, 2D significant points in each of the two extracted images are located. A significant point volume matching (SPVM) method is then proposed to reconstruct the 3D significant body point locations by using 2D posture estimation results. Experimental results show that the proposed SVM-based segmentation method shows better performance than other gray level- and RGB-based segmentation approaches. This paper also shows the effectiveness of the 3D posture estimation results in different postures. PMID:24883422

A method for generating reduced-order combustion mechanisms that satisfy the differential entropy inequality

NASA Astrophysics Data System (ADS)

Ream, Allen E.; Slattery, John C.; Cizmas, Paul G. A.

2018-04-01

This paper presents a new method for determining the Arrhenius parameters of a reduced chemical mechanism such that it satisfies the second law of thermodynamics. The strategy is to approximate the progress of each reaction in the reduced mechanism from the species production rates of a detailed mechanism by using a linear least squares method. A series of non-linear least squares curve fittings are then carried out to find the optimal Arrhenius parameters for each reaction. At this step, the molar rates of production are written such that they comply with a theorem that provides the sufficient conditions for satisfying the second law of thermodynamics. This methodology was used to modify the Arrhenius parameters for the Westbrook and Dryer two-step mechanism and the Peters and Williams three-step mechanism for methane combustion. Both optimized mechanisms showed good agreement with the detailed mechanism for species mole fractions and production rates of most major species. Both optimized mechanisms showed significant improvement over previous mechanisms in minor species production rate prediction. Both optimized mechanisms produced no violations of the second law of thermodynamics.

Synthesis of instrumentally and historically recorded earthquakes and studying their spatial statistical relationship (A case study: Dasht-e-Biaz, Eastern Iran)

NASA Astrophysics Data System (ADS)

Jalali, Mohammad; Ramazi, Hamidreza

2018-06-01

Earthquake catalogues are the main source of statistical seismology for the long term studies of earthquake occurrence. Therefore, studying the spatiotemporal problems is important to reduce the related uncertainties in statistical seismology studies. A statistical tool, time normalization method, has been determined to revise time-frequency relationship in one of the most active regions of Asia, Eastern Iran and West of Afghanistan, (a and b were calculated around 8.84 and 1.99 in the exponential scale, not logarithmic scale). Geostatistical simulation method has been further utilized to reduce the uncertainties in the spatial domain. A geostatistical simulation produces a representative, synthetic catalogue with 5361 events to reduce spatial uncertainties. The synthetic database is classified using a Geographical Information System, GIS, based on simulated magnitudes to reveal the underlying seismicity patterns. Although some regions with highly seismicity correspond to known faults, significantly, as far as seismic patterns are concerned, the new method highlights possible locations of interest that have not been previously identified. It also reveals some previously unrecognized lineation and clusters in likely future strain release.

Effects of cooking methods on starch and sugar composition of sweetpotato storage roots

PubMed Central

Wei, Shuying; Lu, Guoquan; Cao, Heping

2017-01-01

Sweetpotato has rich nutrition, good ecological adaptability and high yield. There is a lack of knowledge about the effects of cooking methods on starch and sugar components in elite Chinese cultivars. In this study, sweetpotato storage roots from four cultivars “Xinxiang”, “Jinyu”, “Zimei” and “Yuzishu 263” were treated by baking, boiling and steaming and subsequently analyzed for starch content, amylase activity and sugar contents including glucose, fructose, sucrose and maltose. Results indicated that cooking reduced starch content and final amylase activity and increased reducing sugar content especially maltose content, but did not have significant influence on non-reducing sugar content. These effects were different among the four cultivars and three cooking methods. Baking led to the least starch reduction. Storage roots of “Jinyu” contained the highest amount of sugar content and thus sweetest. Sugar composition analysis suggested that cultivars “Xinxiang” and “Jinyu” belong to high-maltose cultivars. This study may provide useful information for evaluating the cooking quality of sweetpotato cultivars. PMID:28827808

Radiation Protection Methods for the Interventionalist’s Hands: Use of an Extension Tube

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dixon, Shaheen, E-mail: shaheen7noorani@gmail.com; Schick, Daniel, E-mail: Daniel.Schick@health.qld.gov.au; Harper, John, E-mail: John-Harper@health.qld.gov.au

2015-04-15

PurposeCumulative radiation exposure to the hands during certain interventional procedures may be high. It is important to decrease the amount of radiation to the operator due to the possibility of deterministic effects. We performed a pilot study to demonstrate a significant decrease in operator dose when using extension tubing (ET) in combination with shielding and collimation during a simulated percutaneous transhepatic cholangiogram (PTC) procedure.MethodsA whole body, anthropomorphic phantom was used to simulate the patient. A Unfors-Xi Survey detector (to measure scatter) supported by a retort stand and trolley was placed in various positions to simulate the position of hands andmore » eyes/thyroid of an interventionalist. Radiation dose was measured simulating left and right-sided PTC punctures with and without a lead shield, and with and without ET.ResultsRegarding the radiation dose to the hands; the use of an ET reduces dose by 54 % in right-sided PTC punctures without a shield and by 91 % if used in combination with a shield. For left-sided PTC punctures, ET reduces hand dose by 75 %. The use of collimation decreases hand dose by approximately 60 %. The use of shielding reduces dose to the eyes/thyroid by 98 %.ConclusionsThe dose to the hands can be significantly reduced with the appropriate use of a shield, ET, and tight collimation. The use of a shield is paramount to reduce dose to the eyes/thyroid. It is important for interventionalists to adhere to radiation protective practice considering the potential deterministic effects during a lifelong career.« less

Reduced-Order Blade Mistuning Analysis Techniques Developed for the Robust Design of Engine Rotors

NASA Technical Reports Server (NTRS)

Min, James B.

2004-01-01

The primary objective of this research program is to develop vibration analysis tools, design tools, and design strategies to significantly improve the safety and robustness of turbine engine rotors. Bladed disks in turbine engines always feature small, random blade-to-blade differences, or mistuning. Mistuning can lead to a dramatic increase in blade forced-response amplitudes and stresses. Ultimately, this results in high-cycle fatigue, which is a major safety and cost concern. In this research program, the necessary steps will be taken to transform a state-of-the-art vibration analysis tool, the Turbo-Reduce forced-response prediction code, into an effective design tool by enhancing and extending the underlying modeling and analysis methods. Furthermore, novel techniques will be developed to assess the safety of a given design. In particular, a procedure will be established for using eigenfrequency curve veerings to identify "danger zones" in the operating conditions--ranges of rotational speeds and engine orders in which there is a great risk that the rotor blades will suffer high stresses. This work also will aid statistical studies of the forced response by reducing the necessary number of simulations. Finally, new strategies for improving the design of rotors will be pursued. Several methods will be investigated, including the use of intentional mistuning patterns to mitigate the harmful effects of random mistuning, and the modification of disk stiffness to avoid reaching critical values of interblade coupling in the desired operating range. Recent research progress is summarized in the following paragraphs. First, significant progress was made in the development of the component mode mistuning (CMM) and static mode compensation (SMC) methods for reduced-order modeling of mistuned bladed disks (see the following figure). The CMM method has been formalized and extended to allow a general treatment of mistuning. In addition, CMM allows individual mode mistuning, which accounts for the realistic effects of local variations in blade properties that lead to different mistuning values for different mode types (e.g., mistuning of the first torsion mode versus the second flexural mode). The accuracy and efficiency of the CMM method and the corresponding Turbo-Reduce code were validated for an example finite element model of a bladed disk.

Impact and appreciation of two methods aiming at reducing hazardous drug environmental contamination: The centralization of the priming of IV tubing in the pharmacy and use of a closed-system transfer device.

PubMed

Guillemette, Annie; Langlois, Hélène; Voisine, Maxime; Merger, Delphine; Therrien, Roxane; Mercier, Genevieve; Lebel, Denis; Bussières, Jean-François

2014-12-01

The main objective was to evaluate the impact of two methods aiming at reducing hazardous drug environmental contamination: the centralization of the priming of IV tubing in the pharmacy and the use of a closed-system transfer device. The secondary objective was to evaluate the satisfaction of pharmacy technicians using a survey. Sites in the hematology-oncology satellite pharmacy and care unit were analyzed for the presence of cyclophosphamide, ifosfamide and methotrexate before and after the centralization of the priming of IV tubing in the pharmacy and before and after using a closed-system transfer device. The limits of detection for cyclophosphamide, ifosfamide and methotrexate were, respectively, of 0.0015 ng/cm(2), 0.0012 ng/cm(2) and 0.0060 ng/cm(2). The pharmacy technician satisfaction was evaluated using a questionnaire. A total of 225 samples was quantified. After the centralization of priming in the pharmacy, no significant difference was found in the proportion of positive samples for cyclophosphamide, ifosfamide and methotrexate. Traces of cyclophosphamide found on the floor in patient care areas was significantly reduced (median[min-max] 0.08[0.06-0.09]ng/cm(2) vs. 0.03[0.02-0.05], p < 0.0001). After using a closed-system transfer device, a significant difference was found for the proportion of cyclophosphamide positive samples (15/45(33%) vs. 0/45(0%), p < 0.0001), but no significant difference was found for ifosfamide (12/45(27%) vs. 5/45(11%), p = 0.059) and methotrexate (1/45(2%) vs. 2/45(4%), p = 0.557). Pharmacy technicians raised issues following the centralization of priming (e.g. workload) and the use of closed-system transfer devices (e.g. spills, particles, workload and handling difficulties). The centralization of the priming of IV tubing in the pharmacy reduced floor contamination in patient care areas without increasing surface contamination in the pharmacy. Closed-system transfer devices reduced contamination in pharmacy, but handling issues were raised by pharmacy technicians. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Efficient experimental design for uncertainty reduction in gene regulatory networks.

PubMed

Dehghannasiri, Roozbeh; Yoon, Byung-Jun; Dougherty, Edward R

2015-01-01

An accurate understanding of interactions among genes plays a major role in developing therapeutic intervention methods. Gene regulatory networks often contain a significant amount of uncertainty. The process of prioritizing biological experiments to reduce the uncertainty of gene regulatory networks is called experimental design. Under such a strategy, the experiments with high priority are suggested to be conducted first. The authors have already proposed an optimal experimental design method based upon the objective for modeling gene regulatory networks, such as deriving therapeutic interventions. The experimental design method utilizes the concept of mean objective cost of uncertainty (MOCU). MOCU quantifies the expected increase of cost resulting from uncertainty. The optimal experiment to be conducted first is the one which leads to the minimum expected remaining MOCU subsequent to the experiment. In the process, one must find the optimal intervention for every gene regulatory network compatible with the prior knowledge, which can be prohibitively expensive when the size of the network is large. In this paper, we propose a computationally efficient experimental design method. This method incorporates a network reduction scheme by introducing a novel cost function that takes into account the disruption in the ranking of potential experiments. We then estimate the approximate expected remaining MOCU at a lower computational cost using the reduced networks. Simulation results based on synthetic and real gene regulatory networks show that the proposed approximate method has close performance to that of the optimal method but at lower computational cost. The proposed approximate method also outperforms the random selection policy significantly. A MATLAB software implementing the proposed experimental design method is available at http://gsp.tamu.edu/Publications/supplementary/roozbeh15a/.

Efficient experimental design for uncertainty reduction in gene regulatory networks

PubMed Central

2015-01-01

Background An accurate understanding of interactions among genes plays a major role in developing therapeutic intervention methods. Gene regulatory networks often contain a significant amount of uncertainty. The process of prioritizing biological experiments to reduce the uncertainty of gene regulatory networks is called experimental design. Under such a strategy, the experiments with high priority are suggested to be conducted first. Results The authors have already proposed an optimal experimental design method based upon the objective for modeling gene regulatory networks, such as deriving therapeutic interventions. The experimental design method utilizes the concept of mean objective cost of uncertainty (MOCU). MOCU quantifies the expected increase of cost resulting from uncertainty. The optimal experiment to be conducted first is the one which leads to the minimum expected remaining MOCU subsequent to the experiment. In the process, one must find the optimal intervention for every gene regulatory network compatible with the prior knowledge, which can be prohibitively expensive when the size of the network is large. In this paper, we propose a computationally efficient experimental design method. This method incorporates a network reduction scheme by introducing a novel cost function that takes into account the disruption in the ranking of potential experiments. We then estimate the approximate expected remaining MOCU at a lower computational cost using the reduced networks. Conclusions Simulation results based on synthetic and real gene regulatory networks show that the proposed approximate method has close performance to that of the optimal method but at lower computational cost. The proposed approximate method also outperforms the random selection policy significantly. A MATLAB software implementing the proposed experimental design method is available at http://gsp.tamu.edu/Publications/supplementary/roozbeh15a/. PMID:26423515

An Efficient Method Coupling Kernel Principal Component Analysis with Adjoint-Based Optimal Control and Its Goal-Oriented Extensions

NASA Astrophysics Data System (ADS)

Thimmisetty, C.; Talbot, C.; Tong, C. H.; Chen, X.

2016-12-01

The representativeness of available data poses a significant fundamental challenge to the quantification of uncertainty in geophysical systems. Furthermore, the successful application of machine learning methods to geophysical problems involving data assimilation is inherently constrained by the extent to which obtainable data represent the problem considered. We show how the adjoint method, coupled with optimization based on methods of machine learning, can facilitate the minimization of an objective function defined on a space of significantly reduced dimension. By considering uncertain parameters as constituting a stochastic process, the Karhunen-Loeve expansion and its nonlinear extensions furnish an optimal basis with respect to which optimization using L-BFGS can be carried out. In particular, we demonstrate that kernel PCA can be coupled with adjoint-based optimal control methods to successfully determine the distribution of material parameter values for problems in the context of channelized deformable media governed by the equations of linear elasticity. Since certain subsets of the original data are characterized by different features, the convergence rate of the method in part depends on, and may be limited by, the observations used to furnish the kernel principal component basis. By determining appropriate weights for realizations of the stochastic random field, then, one may accelerate the convergence of the method. To this end, we present a formulation of Weighted PCA combined with a gradient-based means using automatic differentiation to iteratively re-weight observations concurrent with the determination of an optimal reduced set control variables in the feature space. We demonstrate how improvements in the accuracy and computational efficiency of the weighted linear method can be achieved over existing unweighted kernel methods, and discuss nonlinear extensions of the algorithm.

Defects in ZnO nanorods prepared by a hydrothermal method.

PubMed

Tam, K H; Cheung, C K; Leung, Y H; Djurisić, A B; Ling, C C; Beling, C D; Fung, S; Kwok, W M; Chan, W K; Phillips, D L; Ding, L; Ge, W K

2006-10-26

ZnO nanorod arrays were fabricated using a hydrothermal method. The nanorods were studied by scanning electron microscopy, photoluminescence (PL), time-resolved PL, X-ray photoelectron spectroscopy, and positron annihilation spectroscopy before and after annealing in different environments and at different temperatures. Annealing atmosphere and temperature had significant effects on the PL spectrum, while in all cases the positron diffusion length and PL decay times were increased. We found that, while the defect emission can be significantly reduced by annealing at 200 degrees C, the rods still have large defect concentrations as confirmed by their low positron diffusion length and short PL decay time constants.

Econometric analysis to evaluate the effect of community-based health insurance on reducing informal self-care in Burkina Faso

PubMed Central

Robyn, Paul Jacob; Hill, Allan; Liu, Yuanli; Souares, Aurélia; Savadogo, Germain; Sié, Ali; Sauerborn, Rainer

2012-01-01

Objective This study examines the role of community-based health insurance (CBHI) in influencing health-seeking behaviour in Burkina Faso, West Africa. Community-based health insurance was introduced in Nouna district, Burkina Faso, in 2004 with the goal to improve access to contracted providers based at primary- and secondary-level facilities. The paper specifically examines the effect of CBHI enrolment on reducing the prevalence of seeking modern and traditional methods of self-treatment as the first choice in care among the insured population. Methods Three stages of analysis were adopted to measure this effect. First, propensity score matching was used to minimize the observed baseline differences between the insured and uninsured populations. Second, through matching the average treatment effect on the treated, the effect of insurance enrolment on health-seeking behaviour was estimated. Finally, multinomial logistic regression was applied to model demand for available health care options, including no treatment, traditional self-treatment, modern self-treatment, traditional healers and facility-based care. Results For the first choice in care sought, there was no significant difference in the prevalence of self-treatment among the insured and uninsured populations, reaching over 55% for each group. When comparing the alternative option of no treatment, CBHI played no significant role in reducing the demand for self-care (either traditional or modern) or utilization of traditional healers, while it did significantly increase consumption of facility-based care. The average treatment effect on the treated was insignificant for traditional self-care, modern self-care and traditional healer, but was significant with a positive effect for use of facility care. Discussion While CBHI does have a positive impact on facility care utilization, its effect on reducing the prevalence of self-care is limited. The policy recommendations for improving the CBHI scheme’s responsiveness to population health care demand should incorporate community-based initiatives that offer attractive and appropriate alternatives to self-care. PMID:21414993

Stressors and anxiety in dementia caregiving: multiple mediation analysis of rumination, experiential avoidance, and leisure.

PubMed

Romero-Moreno, R; Losada, A; Márquez-González, M; Mausbach, B T

2016-11-01

Despite the robust associations between stressors and anxiety in dementia caregiving, there is a lack of research examining which factors contribute to explain this relationship. This study was designed to test a multiple mediation model of behavioral and psychological symptoms of dementia (BPSD) and anxiety that proposes higher levels of rumination and experiential avoidance and lower levels of leisure satisfaction as potential mediating variables. The sample consisted of 256 family caregivers. In order to test a simultaneously parallel multiple mediation model of the BPSD to anxiety pathway, a PROCESS method was used and bias-corrected and accelerated bootstrapping method was used to test confidence intervals. Higher levels of stressors significantly predicted anxiety. Greater stressors significantly predicted higher levels of rumination and experiential avoidance, and lower levels of leisure satisfaction. These three coping variables significantly predicted anxiety. Finally, rumination, experiential avoidance, and leisure satisfaction significantly mediated the link between stressors and anxiety. The explained variance for the final model was 47.09%. Significant contrasts were found between rumination and leisure satisfaction, with rumination being a significantly higher mediator. The results suggest that caregivers' experiential avoidance, rumination, and leisure satisfaction may function as mechanisms through which BPSD influence on caregivers' anxiety. Training caregivers in reducing their levels of experiential avoidance and rumination by techniques that foster their ability of acceptance of their negative internal experiences, and increase their level of leisure satisfaction, may be helpful to reduce their anxiety symptoms developed by stressors.

Evaluation of effect of different disposable infection control barriers on light intensity of light-curing unit and microhardness of composite - An in vitro study

PubMed Central

Khode, Rajiv Tarachand; Shenoi, Pratima Ramakrishna; Kubde, Rajesh R.; Makade, Chetana S.; Wadekar, Kanchan D.; Khode, Priyanka Tarachand

2017-01-01

Aims: This study evaluated effect of infection control barriers on light intensity (LI) of light-curing unit (LCU) and microhardness of composite. Materials and Methods: Four different disposable barriers (n = 30) were tested against the control. LI for each barrier was measured with Lux meter. One hundred and fifty Teflon molds were equally divided into five groups of thirty each. Composite was filled in bulk in these molds and cured without and with barrier. Microhardness was evaluated on top and bottom surface of composite specimen with microhardness testing machine and hardness ratio (HR) was derived. Statistical Analysis Used: One-way analysis of variance, Tukey's honestly significant difference test, and paired t-test using SPSS version 18 software. Results: All barriers had significantly reduced the baseline LI of LCU (P < 0.0001), but only Cure Elastic Steri-Shield and latex cut glove pieces (LCGP) significantly reduced the microhardness of the composite (P < 0.05). However, HR determined inadequate curing only with LCGP. Conclusions: Although entire tested barrier significantly reduced the LI; none, except LCGP markedly affected the degree of cure of the composite. PMID:29279622

Segregation of biomedical waste in an South Indian tertiary care hospital

PubMed Central

Sengodan, Vetrivel Chezian

2014-01-01

Introduction: Hospital wastes pose significant public health hazard if not properly managed. Hence, it is necessary to develop and adopt optimal waste management systems in the hospitals. Material and method: Biomedical waste generated in Coimbatore Medical College Hospital was color coded (blue, yellow, and red) and the data was analyzed retrospectively on a daily basis for 3 years (January 2010-December 2012). Results: Effective segregation protocols significantly reduced biomedical waste generated from 2011 to 2012. While biomedical waste of red category was significantly higher (>50%), the category yellow was the least. Per unit (per bed per day) total biomedical waste generated was 68.5, 68.8, and 61.3 grams in 2010, 2011, and 2012, respectively. Discussion: Segregation of biomedical waste at the source of generation is the first and essential step in biomedical waste management. Continuous training, fixing the responsibility on the nursing persons, and constant supervision are the key criteria's in implementing biomedical waste segregation process, which can significantly reduce per unit biomedical waste generated. Conclusion: We highly recommend all hospitals to adopt our protocol and effectively implement them to reduce generation of biomedical waste. PMID:25097419

A method for the reduction of aerodynamic drag of road vehicles

NASA Technical Reports Server (NTRS)

Pamadi, Bandu N.; Taylor, Larry W.; Leary, Terrance O.

1990-01-01

A method is proposed for the reduction of the aerodynamic drag of bluff bodies, particularly for application to road transport vehicles. This technique consists of installation of panels on the forward surface of the vehicle facing the airstream. With the help of road tests, it was demonstrated that the attachment of proposed panels can reduce aerodynamic drag of road vehicles and result in significant fuel cost savings and conservation of energy resources.

Pre- and post-treatment techniques for spacecraft water recovery

NASA Technical Reports Server (NTRS)

Putnam, David F.; Colombo, Gerald V.; Chullen, Cinda

1986-01-01

Distillation-based waste water pretreatment and recovered water posttreatment methods are proposed for the NASA Space Station. Laboratory investigation results are reported for two nonoxidizing urine pretreatment formulas (hexadecyl trimethyl ammonium bromide and Cu/Cr) which minimize the generation of volatile organics, thereby significantly reducing posttreatment requirements. Three posttreatment methods (multifiltration, reverse osmosis, and UV-assisted ozone oxidation) have been identified which appear promising for the removal of organic contaminants from recovered water.

MRI directed bilateral stimulation of the subthalamic nucleus in patients with Parkinson's disease

PubMed Central

Patel, N; Plaha, P; O'Sullivan, K; McCarter, R; Heywood, P; Gill, S

2003-01-01

Objective: Bilateral chronic high frequency deep brain stimulation (DBS) of the subthalamic nucleus (STN) has emerged as an appropriate therapy for patients with advanced Parkinson's disease refractory to medical therapy. Advances in neuroimaging and neurophysiology have led to the development of varied targeting methods for the delivery of this treatment. Intraoperative neurophysiological and clinical monitoring is regarded by many to be mandatory for accurate STN localisation. We have examined efficacy of bilateral STN stimulation using a predominantly magnetic resonance imaging (MRI)-directed technique. Methods: DBS leads were stereotactically implanted into the STN using an MRI directed method, with intraoperative macrostimulation used purely for adjustment. The effects of DBS were evaluated in 16 patients followed up to 12 months, and compared with baseline assessments. Assessments were performed in both off and on medication states, and were based on the Unified Parkinson's Disease Rating Scale (UPDRS) and timed motor tests. Functional status outcomes were examined using the PDQ-39 quality of life questionnaire. A battery of psychometric tests was used to assess cognition. Results: After 12 months, stimulation in the off medication state resulted in significant improvements in Activities of Daily Living and Motor scores (UPDRS parts II and III) by 62% and 61% respectively. Timed motor tests were significantly improved in the off medication state. Motor scores (UPDRS part III) were significantly improved by 40% in the on medication state. Dyskinesias and off duration were significantly reduced and the mean dose of L-dopa equivalents was reduced by half. Psychometric test scores were mostly unchanged or improved. Adverse events were few. Conclusions: An MRI directed targeting method for implantation of DBS leads into the STN can be used safely and effectively, and results are comparable with studies using intraoperative microelectrode neurophysiological targeting. In addition, our method was associated with an efficient use of operating time, and without the necessary costs of microelectrode recording. PMID:14638880

Dexpanthenol enhances skin barrier repair and reduces inflammation after sodium lauryl sulphate-induced irritation.

PubMed

Proksch, E; Nissen, H P

2002-12-01

Dexpanthenol-containing creams have been widely used for treatment of lesions (superficial wounds) of the skin and mucous membranes. Dexpanthenol is converted in tissues to pantothenic acid, a component of coenzyme A. Coenzyme A catalyses early steps in the synthesis of fatty acids and sphingolipids which are of crucial importance for stratum corneum lipid bilayers and cell membrane integrity. In the present study, the effects were examined of a dexpanthenol-containing cream on skin barrier repair, stratum corneum hydration, skin roughness, and inflammation after sodium lauryl sulphate (SLS)-induced irritation. Irritation was induced by application of SLS in patch test chambers. The dexpanthenol-contaming cream or the vehicle were applied twice daily and barrier repair, hydration, roughness, and inflammation of the skin were determined by using biophysical methods. Significantly accelerated skin barrier repair was found in treatments with the dexpanthenol-containing cream (verum) compared with vehicle-treated (placebo) or untreated skin. Both verum and placebo showed an increase in stratum corneum hydration, but significantly more so with the dexpanthenol-containing cream. Both creams reduced skin roughness, but again the verum was superior. The dexpanthenol-containing cream significantly reduced skin redness as a sign of inflammation in contrast to the vehicle, which produced no effect. Treatment with a dexpanthenol-containing cream showed significantly enhanced skin barrier repair and stratum corneum hydration, while reducing skin roughness and inflammation.

The effects of aerobic exercise for persons with migraine and co-existing tension-type headache and neck pain. A randomized, controlled, clinical trial.

PubMed

Krøll, Lotte Skytte; Hammarlund, Catharina Sjödahl; Linde, Mattias; Gard, Gunvor; Jensen, Rigmor Højland

2018-01-01

Aim To evaluate aerobic exercise in migraine and co-existing tension-type headache and neck pain. Methods Consecutively recruited persons with migraine and co-existing tension-type headache and neck pain were randomized into an exercise group or control group. Aerobic exercise consisted of bike/cross-trainer/brisk walking for 45 minutes, three times/week. Controls continued usual daily activities. Pain frequency, intensity, and duration; physical fitness, level of physical activity, well-being and ability to engage in daily activities were assessed at baseline, after treatment and at follow-up. Results Fifty-two persons completed the study. Significant between-group improvements for the exercise group were found for physical fitness, level of physical activity, migraine burden and the ability to engage in physical activity because of reduced impact of tension-type headache and neck pain. Within the exercise group, significant reduction was found for migraine frequency, pain intensity and duration, neck pain intensity, and burden of migraine; an increase in physical fitness and well-being. Conclusions Exercise significantly reduced the burden of migraine and the ability to engage in physical activity because of reduced impact of tension-type headache and neck pain. Exercise also reduced migraine frequency, pain intensity and duration, although this was not significant compared to controls. These results emphasize the importance of regular aerobic exercise for reduction of migraine burden.

A Randomized Clinical Trial of Schinus terebinthifolius Mouthwash to Treat Biofilm-Induced Gingivitis

PubMed Central

Freires, Irlan de Almeida; Alves, Livia Araújo; Ferreira, Gabriela Lacet Silva; Jovito, Vanessa de Carvalho; de Castro, Ricardo Dias; Cavalcanti, Alessandro Leite

2013-01-01

Objectives. This study aimed to investigate the efficacy of a Schinus terebinthifolius (ST) mouthwash in reducing gingival inflammation levels (GI) and biofilm accumulation (BA) in children with gingivitis. Methods. This was a randomized, controlled, triple blind, and phase II clinical trial, with children aged 9–13 years (n = 27) presenting with biofilm-induced gingivitis. The sample was randomized into experimental (0.3125% ST, n = 14) and control (0.12% chlorhexidine/CHX, n = 13) groups. Products were masked as regards color, flavor and aroma. Intervention protocol consisted in supervised rinsing of 10 mL/day for 01 minute for 10 days. Gingival bleeding and simplified oral hygiene indexes were used to assess the efficacy variables, measured at baseline and after intervention by calibrated examiners. Data were statistically treated with paired t-test, unpaired t-test, and Wilcoxon and Mann-Whitney tests (α = .05). Results. It was found that both ST and CHX were able to significantly reduce GI levels after 10 days (P < 0.001) and there was no significant difference between them (P > 0.05). CHX was the only product able to significantly reduce BA after 10 days when compared to baseline (P < 0.05). Conclusion. ST mouthwash showed significant anti-inflammatory activity (equivalent to CHX), but it was not able to reduce biofilm accumulation. PMID:23843886

Association of Nitric Oxide Levels and Endothelial Nitric Oxide Synthase G894T Polymorphism with Coronary Artery Disease in the Iranian Population

PubMed Central

Mahmoodi, Khalil; Nasehi, Leila; Karami, Elham; Soltanpour, Mohammad Soleiman

2016-01-01

Purpose: The endothelial nitric oxide synthase (eNOS) G894T polymorphism has been reported to cause endothelial dysfunction and may have a role in the development of coronary artery disease (CAD). The aim of the present study was to investigate the association of eNOS G894T genetic polymorphism and plasma levels of nitric oxide (NO) with CAD risk in an Iranian population. Materials and Methods: We studied 200 patients with angiographically documented CAD and 100 matched controls. Analysis of G894T genetic polymorphism of eNOS was performed by polymerase chain reaction-restriction fragment length polymorphism method. Plasma levels of NO were determined using Griess method. Biochemical analysis was conducted by routine colorimetric methods. Results: Plasma levels of NO were significantly lower in CAD patients than control subjects (41.60±12.70 vs. 55.48±16.57, P=0.001). Also, the mean plasma levels of NO were significantly lower in T allele carriers of eNOS G894T polymorphism than G allele carriers (P<0.001). The genotype distribution and minor T allele frequency of eNOS G894T polymorphism significantly differed between CAD patients and control subjects (P<0.05). However, no significant association was found between the eNOS G894T polymorphism and the severity of CAD (number of diseased vessel) or the lipid profile of CAD patients (P>0.05). Conclusion: Reduced plasma level of NO is associated with increased risk of CAD in our population. Moreover, eNOS G894T polymorphism is a significant risk factor for CAD development via reducing the plasma levels of NO. However, eNOS G894T polymorphism is not a contributing factor for the severity of CAD. PMID:27699157

A web-based program to increase knowledge and reduce cigarette and nargila smoking among Arab university students in Israel: mixed-methods study to test acceptability.

PubMed

Essa-Hadad, Jumanah; Linn, Shai; Rafaeli, Sheizaf

2015-02-20

Among Arab citizens in Israel, cigarette and nargila (hookah, waterpipe) smoking is a serious public health problem, particularly among the young adult population. With the dramatic increase of Internet and computer use among Arab college and university students, a Web-based program may provide an easy, accessible tool to reduce smoking rates without heavy resource demands required by traditional methods. The purpose of this research was to examine the acceptability and feasibility of a pilot Web-based program that provides tailored feedback to increase smoking knowledge and reduce cigarette and nargila smoking behaviors among Arab college/university students in Israel. A pilot Web-based program was developed, consisting of a self-administered questionnaire and feedback system on cigarette and nargila smoking. Arab university students were recruited to participate in a mixed-methods study, using both quantitative (pre-/posttest study design) and qualitative tools. A posttest was implemented at 1 month following participation in the intervention to assess any changes in smoking knowledge and behaviors. Focus group sessions were implemented to assess acceptability and preferences related to the Web-based program. A total of 225 participants-response rate of 63.2% (225/356)-completed the intervention at baseline and at 1-month poststudy, and were used for the comparative analysis. Statistically significant reductions in nargila smoking among participants (P=.001) were found. The intervention did not result in reductions in cigarette smoking. However, the tailored Web intervention resulted in statistically significant increases in the intention to quit smoking (P=.021). No statistically significant increases in knowledge were seen at 1-month poststudy. Participants expressed high satisfaction with the intervention and 93.8% (211/225) of those who completed the intervention at both time intervals reported that they would recommend the program to their friends, indicating excellent acceptability and feasibility of the intervention. This was further emphasized in the focus group sessions. A tailored Web-based program may be a promising tool to reduce nargila smoking among Arab university students in Israel. The tailored Web intervention was not successful at significantly reducing cigarette smoking or increasing knowledge. However, the intervention did increase participants' intention to quit smoking. Participants considered the Web-based tool to be an interesting, feasible, and highly acceptable strategy. ISRCTN registry ISRCTN59207794; http://www.isrctn.com/ISRCTN59207794 (Archived by WebCite at http://www.webcitation.org/6VkYOBNOJ).

Assessing differential expression in two-color microarrays: a resampling-based empirical Bayes approach.

PubMed

Li, Dongmei; Le Pape, Marc A; Parikh, Nisha I; Chen, Will X; Dye, Timothy D

2013-01-01

Microarrays are widely used for examining differential gene expression, identifying single nucleotide polymorphisms, and detecting methylation loci. Multiple testing methods in microarray data analysis aim at controlling both Type I and Type II error rates; however, real microarray data do not always fit their distribution assumptions. Smyth's ubiquitous parametric method, for example, inadequately accommodates violations of normality assumptions, resulting in inflated Type I error rates. The Significance Analysis of Microarrays, another widely used microarray data analysis method, is based on a permutation test and is robust to non-normally distributed data; however, the Significance Analysis of Microarrays method fold change criteria are problematic, and can critically alter the conclusion of a study, as a result of compositional changes of the control data set in the analysis. We propose a novel approach, combining resampling with empirical Bayes methods: the Resampling-based empirical Bayes Methods. This approach not only reduces false discovery rates for non-normally distributed microarray data, but it is also impervious to fold change threshold since no control data set selection is needed. Through simulation studies, sensitivities, specificities, total rejections, and false discovery rates are compared across the Smyth's parametric method, the Significance Analysis of Microarrays, and the Resampling-based empirical Bayes Methods. Differences in false discovery rates controls between each approach are illustrated through a preterm delivery methylation study. The results show that the Resampling-based empirical Bayes Methods offer significantly higher specificity and lower false discovery rates compared to Smyth's parametric method when data are not normally distributed. The Resampling-based empirical Bayes Methods also offers higher statistical power than the Significance Analysis of Microarrays method when the proportion of significantly differentially expressed genes is large for both normally and non-normally distributed data. Finally, the Resampling-based empirical Bayes Methods are generalizable to next generation sequencing RNA-seq data analysis.

Biomechanical effects of sitting with adjustable ischial and lumbar support on occupational low back pain: evaluation of sitting load and back muscle activity

PubMed Central

Makhsous, Mohsen; Lin, Fang; Bankard, James; Hendrix, Ronald W; Hepler, Matthew; Press, Joel

2009-01-01

Background Compared to standing posture, sitting decreases lumbar lordosis, increases low back muscle activity, disc pressure, and pressure on the ischium, which are associated with occupational LBP. A sitting device that reduces spinal load and low back muscle activities may help increase sitting comfort and reduce LBP risk. The objective of this study is to investigate the biomechanical effect of sitting with a reduced ischial support and an enhanced lumbar support (Off-Loading) on load, interface pressure and muscle activities. Methods A laboratory test in low back pain (LBP) and asymptomatic subjects was designed to test the biomechanical effect of using the Off-Loading sitting posture. The load and interface pressure on seat and the backrest, and back muscle activities associated with usual and this Off-Loading posture were recorded and compared between the two postures. Results Compared with Normal (sitting upright with full support of the seat and flat backrest) posture, sitting in Off-Loading posture significantly shifted the center of the force and the peak pressure on the seat anteriorly towards the thighs. It also significantly decreased the contact area on the seat and increased that on the backrest. It decreased the lumbar muscle activities significantly. These effects are similar in individuals with and without LBP. Conclusion Sitting with reduced ischial support and enhanced lumbar support resulted in reduced sitting load on the lumbar spine and reduced the lumbar muscular activity, which may potentially reduce sitting-related LBP. PMID:19193245

[Ice application for reducing pain associated with goserelin acetate injection].

PubMed

Ishii, Kaname; Nagata, Chika; Koshizaki, Eiko; Nishiuchi, Satoko

2013-10-01

We investigated the effectiveness of using an ice pack for reducing the pain associated with goserelin acetate injection. In this study, 39 patients with prostate cancer and 1 patient with breast cancer receiving hormonal therapy with goserelin acetate were enrolled. All patients completed a questionnaire regarding the use of ice application. We used the numerical rating scale (NRS) to assess the pain associated with injection. The NRS scores indicated that the pain was significantly less with ice application than with the usual method (p < 0.001). Further, ice application could decrease the duration of pain sensation. Ice application at the injection site is safe and effective for reducing pain.

First-pass myocardial perfusion MRI with reduced subendocardial dark-rim artifact using optimized Cartesian sampling.

PubMed

Zhou, Zhengwei; Bi, Xiaoming; Wei, Janet; Yang, Hsin-Jung; Dharmakumar, Rohan; Arsanjani, Reza; Bairey Merz, C Noel; Li, Debiao; Sharif, Behzad

2017-02-01

The presence of subendocardial dark-rim artifact (DRA) remains an ongoing challenge in first-pass perfusion (FPP) cardiac magnetic resonance imaging (MRI). We propose a free-breathing FPP imaging scheme with Cartesian sampling that is optimized to minimize the DRA and readily enables near-instantaneous image reconstruction. The proposed FPP method suppresses Gibbs ringing effects-a major underlying factor for the DRA-by "shaping" the underlying point spread function through a two-step process: 1) an undersampled Cartesian sampling scheme that widens the k-space coverage compared to the conventional scheme; and 2) a modified parallel-imaging scheme that incorporates optimized apodization (k-space data filtering) to suppress Gibbs-ringing effects. Healthy volunteer studies (n = 10) were performed to compare the proposed method against the conventional Cartesian technique-both using a saturation-recovery gradient-echo sequence at 3T. Furthermore, FPP imaging studies using the proposed method were performed in infarcted canines (n = 3), and in two symptomatic patients with suspected coronary microvascular dysfunction for assessment of myocardial hypoperfusion. Width of the DRA and the number of DRA-affected myocardial segments were significantly reduced in the proposed method compared to the conventional approach (width: 1.3 vs. 2.9 mm, P < 0.001; number of segments: 2.6 vs. 8.7; P < 0.0001). The number of slices with severe DRA was markedly lower for the proposed method (by 10-fold). The reader-assigned image quality scores were similar (P = 0.2), although the quantified myocardial signal-to-noise ratio was lower for the proposed method (P < 0.05). Animal studies showed that the proposed method can detect subendocardial perfusion defects and patient results were consistent with the gold-standard invasive test. The proposed free-breathing Cartesian FPP imaging method significantly reduces the prevalence of severe DRAs compared to the conventional approach while maintaining similar resolution and image quality. 2 J. Magn. Reson. Imaging 2017;45:542-555. © 2016 International Society for Magnetic Resonance in Medicine.

A Particle Batch Smoother Approach to Snow Water Equivalent Estimation

NASA Technical Reports Server (NTRS)

Margulis, Steven A.; Girotto, Manuela; Cortes, Gonzalo; Durand, Michael

2015-01-01

This paper presents a newly proposed data assimilation method for historical snow water equivalent SWE estimation using remotely sensed fractional snow-covered area fSCA. The newly proposed approach consists of a particle batch smoother (PBS), which is compared to a previously applied Kalman-based ensemble batch smoother (EnBS) approach. The methods were applied over the 27-yr Landsat 5 record at snow pillow and snow course in situ verification sites in the American River basin in the Sierra Nevada (United States). This basin is more densely vegetated and thus more challenging for SWE estimation than the previous applications of the EnBS. Both data assimilation methods provided significant improvement over the prior (modeling only) estimates, with both able to significantly reduce prior SWE biases. The prior RMSE values at the snow pillow and snow course sites were reduced by 68%-82% and 60%-68%, respectively, when applying the data assimilation methods. This result is encouraging for a basin like the American where the moderate to high forest cover will necessarily obscure more of the snow-covered ground surface than in previously examined, less-vegetated basins. The PBS generally outperformed the EnBS: for snow pillows the PBSRMSE was approx.54%of that seen in the EnBS, while for snow courses the PBSRMSE was approx.79%of the EnBS. Sensitivity tests show relative insensitivity for both the PBS and EnBS results to ensemble size and fSCA measurement error, but a higher sensitivity for the EnBS to the mean prior precipitation input, especially in the case where significant prior biases exist.

Innovative Adaptive Control Method Demonstrated for Active Suppression of Instabilities in Engine Combustors

NASA Technical Reports Server (NTRS)

Kopasakis, George

2005-01-01

This year, an improved adaptive-feedback control method was demonstrated that suppresses thermoacoustic instabilities in a liquid-fueled combustor of a type used in aircraft engines. Extensive research has been done to develop lean-burning (low fuel-to-air ratio) combustors that can reduce emissions throughout the mission cycle to reduce the environmental impact of aerospace propulsion systems. However, these lean-burning combustors are susceptible to thermoacoustic instabilities (high-frequency pressure waves), which can fatigue combustor components and even downstream turbine blades. This can significantly decrease the safe operating life of the combustor and turbine. Thus, suppressing the thermoacoustic combustor instabilities is an enabling technology for meeting the low-emission goals of the NASA Ultra-Efficient Engine Technology (UEET) Project.

Reducing the cost of using collocation to compute vibrational energy levels: Results for CH2NH.

PubMed

Avila, Gustavo; Carrington, Tucker

2017-08-14

In this paper, we improve the collocation method for computing vibrational spectra that was presented in the work of Avila and Carrington, Jr. [J. Chem. Phys. 143, 214108 (2015)]. Known quadrature and collocation methods using a Smolyak grid require storing intermediate vectors with more elements than points on the Smolyak grid. This is due to the fact that grid labels are constrained among themselves and basis labels are constrained among themselves. We show that by using the so-called hierarchical basis functions, one can significantly reduce the memory required. In this paper, the intermediate vectors have only as many elements as the Smolyak grid. The ideas are tested by computing energy levels of CH 2 NH.

SAR measurements of surface displacements at Augustine Volcano, Alaska from 1992 to 2005

USGS Publications Warehouse

Lee, C.-W.; Lu, Z.; Kwoun, Oh-Ig

2007-01-01

Augustine volcano is an active stratovolcano located at the southwest of Anchorage, Alaska. Augustine volcano had experienced seven significantly explosive eruptions in 1812, 1883, 1908, 1935, 1963, 1976, and 1986, and a minor eruption in January 2006. We measured the surface displacements of the volcano by radar interferometry and GPS before and after the eruption in 2006. ERS-1/2, RADARSAT-1 and ENVISAT SAR data were used for the study. Multiple interferograms were stacked to reduce artifacts caused by different atmospheric conditions. Least square (LS) method was used to reduce atmospheric artifacts. Singular value decomposition (SVD) method was applied for retrieval of time sequential deformations. Satellite radar interferometry helps to understand the surface displacements system of Augustine volcano. ?? 2007 IEEE.

SAR measurements of surface displacements at Augustine Volcano, Alaska from 1992 to 2005

USGS Publications Warehouse

Lee, C.-W.; Lu, Z.; Kwoun, Oh-Ig

2008-01-01

Augustine volcano is an active stratovolcano located at the southwest of Anchorage, Alaska. Augustine volcano had experienced seven significantly explosive eruptions in 1812, 1883, 1908, 1935, 1963, 1976, and 1986, and a minor eruption in January 2006. We measured the surface displacements of the volcano by radar interferometry and GPS before and after the eruption in 2006. ERS-1/2, RADARSAT-1 and ENVISAT SAR data were used for the study. Multiple interferograms were stacked to reduce artifacts caused by different atmospheric conditions. Least square (LS) method was used to reduce atmospheric artifacts. Singular value decomposition (SVD) method was applied for retrieval of time sequential deformations. Satellite radar interferometry helps to understand the surface displacements system of Augustine volcano. ?? 2007 IEEE.

Fibrin tissue adhesive reduces postoperative blood loss in total knee arthroplasty.

PubMed

Sabatini, Luigi; Trecci, Andrea; Imarisio, Daniele; Uslenghi, Marco Davide; Bianco, Giuseppe; Scagnelli, Roberto

2012-09-01

Blood transfusion is often required in total knee replacement; various methods of blood preservation have been studied. The best solution is to reduce the loss of blood during and after surgery. We designed this study to evaluate the hemostatic efficacy and safety of fibrin tissue adhesive (Quixil) in patients receiving total knee arthroplasty [low contact stress (LCS, DePuy, Warsaw, IN, US) cementless total knee replacement (TKR)] with a prospective, randomized, standard treatment controlled study. Thirty-five patients were randomized to receive treatment with fibrin tissue adhesive (treatment group), and 35 were randomized to be managed with postoperative blood recovery and reinfusion (control group). Blood loss in suction drain, decrease in hemoglobin values, and transfusions were recorded. A significant reduction in apparent total blood loss was detected in the treatment group compared with the control group. There was also a lower decrease in hemoglobin level, although this difference was not significant. When fibrin tissue adhesive was administered, the need for transfusions was lower. No major adverse events were recorded in our series. Fibrin tissue adhesive reduced blood loss in TKR and seemed to significantly reduce the need for blood transfusion. Fibrin tissue adhesive can be an appropriate solution to enhance hemostasis and vessel sealing at the operative site in TKR, in order to reduce blood loss after surgery and the risk of complications.

Autoclave method for rapid preparation of bacterial PCR-template DNA.

PubMed

Simmon, Keith E; Steadman, Dewey D; Durkin, Sarah; Baldwin, Amy; Jeffrey, Wade H; Sheridan, Peter; Horton, Rene; Shields, Malcolm S

2004-02-01

An autoclave method for preparing bacterial DNA for PCR template is presented, it eliminates the use of detergents, organic solvents, and mechanical cellular disruption approaches, thereby significantly reducing processing time and costs while increasing reproducibility. Bacteria are lysed by rapid heating and depressurization in an autoclave. The lysate, cleared by microcentrifugation, was either used directly in the PCR reaction, or concentrated by ultrafiltration. This approach was compared with seven established methods of DNA template preparation from four bacterial sources which included boiling Triton X-100 and SDS, bead beating, lysozyme/proteinase K, and CTAB lysis method components. Bacteria examined were Enterococcus and Escherichia coli, a natural marine bacterial community and an Antarctic cyanobacterial-mat. DNAs were tested for their suitability as PCR templates by repetitive element random amplified polymorphic DNA (RAPD) and denaturing gradient gel electrophoresis (DGGE) analysis. The autoclave method produced PCR amplifiable template comparable or superior to the other methods, with greater reproducibility, much shorter processing time, and at a significantly lower cost.

Testing an automated method to estimate ground-water recharge from streamflow records

USGS Publications Warehouse

Rutledge, A.T.; Daniel, C.C.

1994-01-01

The computer program, RORA, allows automated analysis of streamflow hydrographs to estimate ground-water recharge. Output from the program, which is based on the recession-curve-displacement method (often referred to as the Rorabaugh method, for whom the program is named), was compared to estimates of recharge obtained from a manual analysis of 156 years of streamflow record from 15 streamflow-gaging stations in the eastern United States. Statistical tests showed that there was no significant difference between paired estimates of annual recharge by the two methods. Tests of results produced by the four workers who performed the manual method showed that results can differ significantly between workers. Twenty-two percent of the variation between manual and automated estimates could be attributed to having different workers perform the manual method. The program RORA will produce estimates of recharge equivalent to estimates produced manually, greatly increase the speed od analysis, and reduce the subjectivity inherent in manual analysis.

Effect of different cooking methods on minerals, vitamins and nutritional quality indices of kutum roach (Rutilus frisii kutum).

PubMed

Hosseini, Hedayat; Mahmoudzadeh, Maryam; Rezaei, Masoud; Mahmoudzadeh, Leila; Khaksar, Ramin; Khosroshahi, Nader Karimian; Babakhani, Aria

2014-04-01

In this study, the influence of four cooking methods (baking, boiling, microwaving and frying) was evaluated on the nutritional value of kutum roach. Proximate, fatty acid composition, vitamin and mineral contents and also nutritional quality indices (NQI) of kutum roach were investigated before and after cooking treatment. All treated samples showed increase in protein, ash and lipid contents and decrease in the content of total omega-3 fatty acids (n-3) in comparison to raw fish fillets (control group). Cooking methods had no significant effect on omega-6 fatty acids (n-6) except for frying that increased it. Nonetheless, all of the cooking methods reduced vitamin B1, A and D contents. Boiling significantly decreased mineral contents including Na, K, P and Zn. Considering the overall nutritional quality indices, vitamin and mineral contents, baking is the best cooking method among other applied methods. Copyright © 2013 Elsevier Ltd. All rights reserved.

Physical exercises for breast cancer survivors: effects of 10 weeks of training on upper limb circumferences

PubMed Central

Di Blasio, Andrea; Morano, Teresa; Bucci, Ines; Di Santo, Serena; D’Arielli, Alberto; Castro, Cristina Gonzalez; Cugusi, Lucia; Cianchetti, Ettore; Napolitano, Giorgio

2016-01-01

[Purpose] The aims of this study were to verify the effects on upper limb circumferences and total body extracellular water of 10 weeks of Nordic Walking (NW) and Walking (W), both alone and combined with a series of exercises created for breast cancer survivors, the ISA method. [Subjects and Methods] Twenty breast cancer survivors were randomly assigned to 4 different training groups and evaluated for upper limb circumferences, total body and extracellular water. [Results] The breast cancer survivors who performed NW, alone and combined with the ISA method, and Walking combined with the ISA method (but not alone) showed significantly reduced arm and forearm circumferences homolateral to the surgical intervention. [Conclusion] For breast cancer survivors, NW, alone and combined with the ISA method, and Walking combined with the ISA method should be prescribed to prevent the onset and to treat light forms of upper limb lymphedema because Walking training practiced alone had no significant effect on upper limb circumference reduction. PMID:27821934

Reducing the width of confidence intervals for the difference between two population means by inverting adaptive tests.

PubMed

O'Gorman, Thomas W

2018-05-01

In the last decade, it has been shown that an adaptive testing method could be used, along with the Robbins-Monro search procedure, to obtain confidence intervals that are often narrower than traditional confidence intervals. However, these confidence interval limits require a great deal of computation and some familiarity with stochastic search methods. We propose a method for estimating the limits of confidence intervals that uses only a few tests of significance. We compare these limits to those obtained by a lengthy Robbins-Monro stochastic search and find that the proposed method is nearly as accurate as the Robbins-Monro search. Adaptive confidence intervals that are produced by the proposed method are often narrower than traditional confidence intervals when the distributions are long-tailed, skewed, or bimodal. Moreover, the proposed method of estimating confidence interval limits is easy to understand, because it is based solely on the p-values from a few tests of significance.

Nitrate-nitrogen reduction by established tree and pasture buffer strips associated with a cattle feedlot effluent disposal area near Armidale, NSW Australia.

PubMed

Wang, Liangmin; Duggin, John A; Nie, Daoping

2012-05-30

Vegetated buffer strips have been recognized as an important element in overall agro-ecosystem management to reduce the delivery of non-point source pollutants from agricultural land to inland water systems. A buffer strip experiment consisting of two tree species (Eucalyptus camaldulensis and Casuarina cunninghamiana) with two planting densities and a pasture treatment was conducted to determine the effectiveness of NO(3)-N removal from a cattle feedlot effluent disposal area at Tullimba near Armidale, NSW Australia. Different management methods were applied for the buffers where grass and weeds were mowed 2-3 times during the second and third years and were not managed during the rest experimental years for the tree buffer, while grass was harvested 1-3 times per year for the pasture buffer. The differences between tree species and planting density significantly affected tree growth, but the growth difference did not significantly affect their capacities to reduce NO(3)-N in soil surface runoff and groundwater. On average for all the tree and pasture treatments, the buffer strips reduced NO(3)-N concentration by 8.5%, 14.7% and 14.4% for the surface runoff, shallow and deep groundwater respectively. The tree and pasture buffer strips were not significantly different in NO(3)-N reduction for both shallow and deep groundwater while the pasture buffer strips reduced significantly more NO(3)-N concentration in surface runoff than the tree buffer strips. Both buffer strips reduced more than 50% of surface runoff volume indicating that both the tree and pasture buffer strips were efficient at removing water and nutrients, mostly through a significant reduction in soil surface runoff volume. Copyright © 2012 Elsevier Ltd. All rights reserved.

Randomised, double blind trial of two loading dose regimens of diamorphine in ventilated newborn infants.

PubMed Central

Barker, D. P.; Simpson, J.; Pawula, M.; Barrett, D. A.; Shaw, P. N.; Rutter, N.

1995-01-01

AIMS--To compare the safety and efficacy of two loading doses of diamorphine in 27 ventilated newborn infants in a randomised double blind trial. METHODS--Fifty or 200 mcg/kg were infused intravenously over 30 minutes, followed by a 15 mcg/kg/hour continuous infusion. Serial measurements were made of physiology, behaviour, and stress hormones. RESULTS--Both loading doses produced small but significant falls in blood pressure. The 200 mcg/kg dose produced greater respiratory depression, and two infants deteriorated clinically, requiring resuscitation. Loading reduced respiratory effort in most of the infants, but had little effect on behavioural activity. Stress hormone concentrations were reduced at six hours in both dosage groups; differences between loading doses were not significant. Morphine, morphine-3-glucuronide, and morphine-6-glucuronide were detected in the plasma of all patients. No significant differences in concentrations between loading doses were found. CONCLUSIONS--Diamorphine reduces the stress response in ventilated newborn infants. A high loading dose confers no benefit, and may produce undesirable physiological effects. A 50 mcg/kg loading dose seems to be safe and effective. PMID:7552591

Reducing unplanned pregnancy and abortion in Zimbabwe through postabortion contraception.

PubMed

Johnson, Brooke R; Ndhlovu, Singatsho; Farr, Sherry L; Chipato, Tsungai

2002-06-01

In many countries, women treated for complications from spontaneous or unsafely induced abortion lack access to contraceptive services. As a result, many of them soon have a subsequent unplanned pregnancy or a repeat abortion, placing their health at increased risk. This report presents the results of a prospective intervention study on postabortion family planning conducted in the two largest public hospitals in Zimbabwe. Women at Harare Central Hospital, in the capital, received a postabortion family planning intervention, and Mpilo Central Hospital, in Bulawayo, served as the control site. The study cohort was 982 women, 527 of whom were followed for a 12-month period. During the follow-up period, significantly more women used highly effective methods of contraception, significantly fewer unplanned pregnancies occurred, and fewer repeat abortions were performed at the intervention site than at the control site. These results offer compelling evidence that ward-based contraceptive services provided to women treated for incomplete abortion can significantly reduce subsequent unplanned pregnancies. The results also suggest that postabortion family planning services can reduce the incidence of repeat abortion.

Interventions Delivered in Clinical Settings are Effective in Reducing Risk of HIV Transmission Among People Living with HIV: Results from the Health Resources and Services Administration (HRSA)’s Special Projects of National Significance Initiative

PubMed Central

Shade, Starley B.; Rose, Carol Dawson; Koester, Kimberly; Maiorana, Andre; Malitz, Faye E.; Bie, Jennifer; Kang-Dufour, Mi-Suk; Morin, Stephen F.

2010-01-01

To support expanded prevention services for people living with HIV, the US Health Resources and Services Administration (HRSA) sponsored a 5-year initiative to test whether interventions delivered in clinical settings were effective in reducing HIV transmission risk among HIV-infected patients. Across 13 demonstration sites, patients were randomized to one of four conditions. All interventions were associated with reduced unprotected vaginal and/or anal intercourse with persons of HIV-uninfected or unknown status among the 3,556 participating patients. Compared to the standard of care, patients assigned to receive interventions from medical care providers reported a significant decrease in risk after 12 months of participation. Patients receiving prevention services from health educators, social workers or paraprofessional HIV-infected peers reported significant reduction in risk at 6 months, but not at 12 months. While clinics have a choice of effective models for implementing prevention programs for their HIV-infected patients, medical provider-delivered methods are comparatively robust. PMID:20229132

Development of an Economical Method to Reduce the Extractable Latex Protein Levels in Finished Dipped Rubber Products

PubMed Central

Perera, Ambegoda Liyanage Harini Amalka

2017-01-01

Natural rubber latex (NRL) allergy is caused by the extractable latex proteins in dipped rubber products. It is a major concern for the consumers who are sensitive to the allergenic extractable proteins (EP) in products such as NRL gloves. Objective of this research was to develop an economical method to reduce the EP in finished dipped NRL products. In order to reduce the EP levels, two natural proteases, bromelain from pineapple and papain from papaya, were extracted and partially purified using (NH4)2SO4. According to the newly developed method, different glove samples were treated with a 5% solution of each partially purified enzyme, for 2 hours at 60°C. Residual amounts of in treated samples were quantified using the modified Lowry assay (ASTM D5712-10). Bromelain displayed a 54 (±11)% reduction of the EP from the dipped rubber products, whereas it was 58 (±8)% with papain. These results clearly indicate that the selected natural proteases, bromelain, and papain contribute significantly towards the reduction of the total EP in finished NRL products. Application of bromelain enzyme for the aforementioned purpose has not been reported up to date, whereas papain has been used to treat raw NRL towards reducing the EP. PMID:28706952

Normalized Rotational Multiple Yield Surface Framework (NRMYSF) stress-strain curve prediction method based on small strain triaxial test data on undisturbed Auckland residual clay soils

NASA Astrophysics Data System (ADS)

Noor, M. J. Md; Ibrahim, A.; Rahman, A. S. A.

2018-04-01

Small strain triaxial test measurement is considered to be significantly accurate compared to the external strain measurement using conventional method due to systematic errors normally associated with the test. Three submersible miniature linear variable differential transducer (LVDT) mounted on yokes which clamped directly onto the soil sample at equally 120° from the others. The device setup using 0.4 N resolution load cell and 16 bit AD converter was capable of consistently resolving displacement of less than 1µm and measuring axial strains ranging from less than 0.001% to 2.5%. Further analysis of small strain local measurement data was performed using new Normalized Multiple Yield Surface Framework (NRMYSF) method and compared with existing Rotational Multiple Yield Surface Framework (RMYSF) prediction method. The prediction of shear strength based on combined intrinsic curvilinear shear strength envelope using small strain triaxial test data confirmed the significant improvement and reliability of the measurement and analysis methods. Moreover, the NRMYSF method shows an excellent data prediction and significant improvement toward more reliable prediction of soil strength that can reduce the cost and time of experimental laboratory test.

Measuring the effectiveness of patient-chosen reminder methods in a private orthodontic practice.

PubMed

Wegrzyniak, Lauren M; Hedderly, Deborah; Chaudry, Kishore; Bollu, Prashanti

2018-05-01

To evaluate the effectiveness of patient-chosen appointment reminder methods (phone call, e-mail, or SMS text) in reducing no-show rates. This was a retrospective case study that determined the correlation between patient-chosen appointment reminder methods and no-show rates in a private orthodontic practice. This study was conducted in a single office location of a multioffice private orthodontic practice using data gathered in 2015. The subjects were patients who self-selected the appointment reminder method (phone call, e-mail, or SMS text). Patient appointment data were collected over a 6-month period. Patient attendance was analyzed with descriptive statistics to determine any significant differences among patient-chosen reminder methods. There was a total of 1193 appointments with an average no-show rate of 2.43% across the three reminder methods. No statistically significant differences ( P = .569) were observed in the no-show rates between the three methods: phone call (3.49%), e-mail (2.68%), and SMS text (1.90%). The electronic appointment reminder methods (SMS text and e-mail) had lower no-show rates compared with the phone call method, with SMS text having the lowest no-show rate of 1.90%. However, since no significant differences were observed between the three patient-chosen reminder methods, providers may want to allow patients to choose their reminder method to decrease no-shows.

A Method to Further Reduce the Perceived Noise of Low Tip Speed Fans

NASA Technical Reports Server (NTRS)

Dittmar, James H.

2000-01-01

The use of low tip speed, high bypass ratio fans is a method for reducing the noise of turbofan jet engines. These fans typically have a low number of rotor blades and a number of stator vanes sufficient to achieve cut-off of the blade passing tone. Their perceived noise levels are typically dominated by broadband noise caused by the rotor wake turbulence - stator interaction mechanism. A 106 bladed, 1100 ft/sec takeoff tip speed fan, the Alternative Low Noise Fan, has been tested and shown to have reduced broadband noise. This reduced noise is believed to be the result of the high rotor blade number. Although this fan with 106 blades would not be practical with materials as they exist today, a fan with 50 or so blades could be practically realized. A noise estimate has indicated that such a 50 bladed, low tip speed fan could be 2 to 3 EPNdB quieter than an 18 bladed fan. If achieved, this level of noise reduction would be significant and points to the use of a high blade number, low tip speed fan as a possible configuration for reduced fan noise.

Utility of Vibratory Stimulation for Reducing Intraoral Injection Pain.

PubMed

Erdogan, Ozgur; Sinsawat, Anatachai; Pawa, Sudeep; Rintanalert, Duangtawan; Vuddhakanok, Suchada

2018-01-01

Intraoral local anesthesia injection is often perceived as a painful and anxiety-causing dental procedure. Vibration stimulus is one of the nonpharmacologic methods used to reduce unwanted sensations of local anesthesia injection. This clinical study evaluated the effectiveness of a recently introduced vibratory stimulation device in intraoral local anesthesia administration. Thirty-two subjects underwent 2 maxillary local anesthesia injections in 2 different sessions: 1 with conventional techniques and 1 with the aid of a vibratory stimulation device (DentalVibe). The pain levels were evaluated with a visual analog scale and the Wong-Baker FACES Pain Rating Scale. The subjects were asked to choose the preferred method for future injections. The data were evaluated statistically. There were no significant differences between the 2 injection methods with regard to either pain evaluation method. The preference of the subjects regarding future injection technique was evenly distributed between the groups. The vibratory stimulation device used in this study did not provide any reduction in pain level associated with maxillary infiltration local anesthesia administration.

Antioxidant capacity of cornelian cherry (Cornus mas L.) - comparison between permanganate reducing antioxidant capacity and other antioxidant methods.

PubMed

Popović, Boris M; Stajner, Dubravka; Slavko, Kevrešan; Sandra, Bijelić

2012-09-15

Ethanol extracts (80% in water) of 10 cornelian cherry (Cornus mas L.) genotypes were studied for antioxidant properties, using methods including DPPH(), ()NO, O(2)(-) and ()OH antiradical powers, FRAP, total phenolic and anthocyanin content (TPC and ACC) and also one relatively new, permanganate method (permanganate reducing antioxidant capacity-PRAC). Lipid peroxidation (LP) was also determined as an indicator of oxidative stress. The data from different procedures were compared and analysed by multivariate techniques (correlation matrix calculation and principal component analysis (PCA)). Significant positive correlations were obtained between TPC, ACC and DPPH(), ()NO, O(2)(-), and ()OH antiradical powers, and also between PRAC and TPC, ACC and FRAP. PCA found two major clusters of cornelian cherry, based on antiradical power, FRAP and PRAC and also on chemical composition. Chemometric evaluation showed close interdependence between PRAC method and FRAP and ACC. There was a huge variation between C. mas genotypes in terms of antioxidant activity. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effects of local anaesthesia or local anaesthesia plus a non-steroidal anti-inflammatory drug on the acute cortisol response of calves to five different methods of castration.

PubMed

Stafford, K J; Mellor, D J; Todd, S E; Bruce, R A; Ward, R N

2002-08-01

The cortisol response of calves to different methods of castration (ring, band, surgical, clamp) with or without local anaesthetic, or local anaesthetic plus a non-steroidal anti-inflammatory drug were recorded. All methods of castration caused a significant cortisol response and by inference pain and distress. Band castration caused a greater cortisol response than ring castration but the responses were eliminated by local anaesthetic. The cortisol response to surgical castration, by traction on the spermatic cords or by cutting across them with an emasculator, was not diminished by local anaesthetic but when ketoprofen was given with local anaesthetic the cortisol response was eliminated. Local anaesthetic did reduce the behavioural response to cutting the scrotum and handling the testes. Clamp castration caused the smallest cortisol response which was reduced or eliminated by local anaesthetic or local anesthetic plus ketoprofen respectively, but this method of castration was not always successful.

Active vibration control for flexible rotor by optimal direct-output feedback control

NASA Technical Reports Server (NTRS)

Nonami, Kenzou; Dirusso, Eliseo; Fleming, David P.

1989-01-01

Experimental research tests were performed to actively control the rotor vibrations of a flexible rotor mounted on flexible bearing supports. The active control method used in the tests is called optimal direct-output feedback control. This method uses four electrodynamic actuators to apply control forces directly to the bearing housings in order to achieve effective vibration control of the rotor. The force actuators are controlled by an analog controller that accepts rotor displacement as input. The controller is programmed with experimentally determined feedback coefficients; the output is a control signal to the force actuators. The tests showed that this active control method reduced the rotor resonance peaks due to unbalance from approximately 250 micrometers down to approximately 25 micrometers (essentially runout level). The tests were conducted over a speed range from 0 to 10,000 rpm; the rotor system had nine critical speeds within this speed range. The method was effective in significantly reducing the rotor vibration for all of the vibration modes and critical speeds.

Active vibration control for flexible rotor by optimal direct-output feedback control

NASA Technical Reports Server (NTRS)

Nonami, K.; Dirusso, E.; Fleming, D. P.

1989-01-01

Experimental research tests were performed to actively control the rotor vibrations of a flexible rotor mounted on flexible bearing supports. The active control method used in the tests is called optimal direct-output feedback control. This method uses four electrodynamic actuators to apply control forces directly to the bearing housings in order to achieve effective vibration control of the rotor. The force actuators are controlled by an analog controller that accepts rotor displacement as input. The controller is programmed with experimentally determined feedback coefficients; the output is a control signal to the force actuators. The tests showed that this active control method reduced the rotor resonance peaks due to unbalance from approximately 250 microns down to approximately 25 microns (essentially runout level). The tests were conducted over a speed range from 0 to 10,000 rpm; the rotor system had nine critical speeds within this speed range. The method was effective in significantly reducing the rotor vibration for all of the vibration modes and critical speeds.

[Pharmacological study on hemostasis, analgesic and anti inflammation effects of the alcohol extract of Hibiscus tiliaceus].

PubMed

Qiu, Fen; Tian, Hui; Zhang, Zhi; Yuan, Xian-Ling; Tan, Yuan-Feng; Ning, Xiao-Qing

2013-10-01

To study the effects of hemostasis, analgesic and anti inflammation of the alcohol extract of Hibiscus tiliaceus and offer pharmacological and experimental basis for its safe and effective use in clinic. The effects of hemostasist were observed with tail breaking method, capillary tube method and slide method; Hot board and body distortion induced by acetic acid methods were applied in mice analgesia experiment, the mice model of acute auricle swelling induced by dmi ethylbenzene and capillary permeability induced by acetic acid were applied to observe the anti inflammatory effects. The alcohol extract of Hibiscus tiliaceus could significantly reduce the bleeding time and the clotting time, delay the plant reaction time and reduce the writhing times of the mice, and it also had effect on inhibiting swelling of mice ear and the permeability of the capillary. These results suggest that the alcohol extract of Hibiscus tiliaceus has the effects of hemostasis, analgesic and anti inflammation.

Effective implementation of the weak Galerkin finite element methods for the biharmonic equation

DOE PAGES

Mu, Lin; Wang, Junping; Ye, Xiu

2017-07-06

The weak Galerkin (WG) methods have been introduced in [11, 12, 17] for solving the biharmonic equation. The purpose of this paper is to develop an algorithm to implement the WG methods effectively. This can be achieved by eliminating local unknowns to obtain a global system with significant reduction of size. In fact this reduced global system is equivalent to the Schur complements of the WG methods. The unknowns of the Schur complement of the WG method are those defined on the element boundaries. The equivalence of theWG method and its Schur complement is established. The numerical results demonstrate themore » effectiveness of this new implementation technique.« less

Effective implementation of the weak Galerkin finite element methods for the biharmonic equation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mu, Lin; Wang, Junping; Ye, Xiu

The weak Galerkin (WG) methods have been introduced in [11, 12, 17] for solving the biharmonic equation. The purpose of this paper is to develop an algorithm to implement the WG methods effectively. This can be achieved by eliminating local unknowns to obtain a global system with significant reduction of size. In fact this reduced global system is equivalent to the Schur complements of the WG methods. The unknowns of the Schur complement of the WG method are those defined on the element boundaries. The equivalence of theWG method and its Schur complement is established. The numerical results demonstrate themore » effectiveness of this new implementation technique.« less

Urinary 11-dehydro-thromboxane B₂ and 2,3-dinor-6-keto-prostaglandin-F₁α in healthy post-menopausal and pre-menopausal women receiving aspirin 100 mg.

PubMed

Hartanto, Marcia Dewi; Arieselia, Zita; Setiabudy, Rianto; Setiawati, Arini; Baziad, Ali

2012-07-01

The prevalence of cardiovascular diseases in women increases sharply after menopause. In postmenopausal women, thromboxane production increases while prostacyclin decreases. Low dose aspirin reduces the production of both thromboxane and prostacyclin. The present study was an open-label clinical trial with two parallel groups of 15 premenopausal women and 15 postmenopausal women. Twenty-four hours urine was collected from each subject before and after aspirin 100 mg daily for 7 days. The concentration of thromboxane and prostacyclin was measured as their metabolites (11-dehydro-thromboxane B(2) and 2,3-dinor-6-keto-prostaglandin-F(1α)) in urine using enzyme immunoassay methods. This study showed that aspirin significantly reduced thromboxane in both groups with significantly larger percentage reduction in postmenopausal women compared to premenopausal women (73.32 vs. 61.13%, p = 0.021). This study also showed that aspirin reduced prostacyclin significantly in both groups, but the percentage reduction between the groups was not significantly different. The decrease in the ratio of 11-dTXB(2)/2,3-dinor-6-keto-PGF(1α) should be compared to assess aspirin efficacy as an antithrombotic. Calculation of the ratio of 11-dTXB(2)/2,3-dinor-6-keto-PGF(1α) before aspirin consumption was higher in postmenopausal women than in premenopausal women. The decrease in 11-dTXB(2)/2,3-dinor-6-keto-PGF(1α) ratio by aspirin was greater in postmenopausal women than in premenopausal women (1.91 vs. 0.17; p = 0.022). It was concluded that aspirin reduced thromboxane and prostacyclin significantly in each group with significant 11-dTXB(2) percentage reduction between groups and non-significant 2,3-dinor-6-keto-PGF(1α) percentage reduction between groups, but reduced the 11-dTXB(2)/2,3-dinor-6-keto-PGF(1α) ratio much larger in postmenopausal women compared to that in premenopausal women.

Nacelle Integration to Reduce the Sonic Boom of Aircraft Designed to Cruise at Supersonic Speeds

NASA Technical Reports Server (NTRS)

Mack, Robert J.

1999-01-01

An empirical method for integrating the engine nacelles on a wing-fuselage-fin(s) configuration has been described. This method is based on Whitham theory and Seebass and George sonic-boom minimization theory, With it, both reduced sonic-boom as well as high aerodynamic efficiency methods can be applied to the conceptual design of a supersonic-cruise aircraft. Two high-speed civil transport concepts were used as examples to illustrate the application of this engine-nacelle integration methodology: (1) a concept with engine nacelles mounted on the aft-fuselage, the HSCT-1OB; and (2) a concept with engine nacelles mounted under an extended-wing center section, the HSCT-11E. In both cases, the key to a significant reduction in the sonic-boom contribution from the engine nacelles was to use the F-function shape of the concept as a guide to move the nacelles further aft on the configuration.

Optimization of Advanced ACTPol Transition Edge Sensor Bolometer Operation Using R(T,I) Transition Measurements

NASA Astrophysics Data System (ADS)

Salatino, Maria

2017-06-01

In the current submm and mm cosmology experiments the focal planes are populated by kilopixel transition edge sensors (TESes). Varying incoming power load requires frequent rebiasing of the TESes through standard current-voltage (IV) acquisition. The time required to perform IVs on such large arrays and the resulting transient heating of the bath reduces the sky observation time. We explore a bias step method that significantly reduces the time required for the rebiasing process. This exploits the detectors' responses to the injection of a small square wave signal on top of the dc bias current and knowledge of the shape of the detector transition R(T,I). This method has been tested on two detector arrays of the Atacama Cosmology Telescope (ACT). In this paper, we focus on the first step of the method, the estimate of the TES %Rn.

Randomization in clinical trials in orthodontics: its significance in research design and methods to achieve it.

PubMed

Pandis, Nikolaos; Polychronopoulou, Argy; Eliades, Theodore

2011-12-01

Randomization is a key step in reducing selection bias during the treatment allocation phase in randomized clinical trials. The process of randomization follows specific steps, which include generation of the randomization list, allocation concealment, and implementation of randomization. The phenomenon in the dental and orthodontic literature of characterizing treatment allocation as random is frequent; however, often the randomization procedures followed are not appropriate. Randomization methods assign, at random, treatment to the trial arms without foreknowledge of allocation by either the participants or the investigators thus reducing selection bias. Randomization entails generation of random allocation, allocation concealment, and the actual methodology of implementing treatment allocation randomly and unpredictably. Most popular randomization methods include some form of restricted and/or stratified randomization. This article introduces the reasons, which make randomization an integral part of solid clinical trial methodology, and presents the main randomization schemes applicable to clinical trials in orthodontics.

Reduction of the coupling vibration between the bending vibrators of the frequency-change-type two-axis acceleration sensor

NASA Astrophysics Data System (ADS)

Sugawara, Sumio; Sasaki, Yoshifumi; Kudo, Subaru

2018-07-01

The frequency-change-type two-axis acceleration sensor uses a cross-type vibrator consisting of four bending vibrators. When coupling vibration exists between these four bending vibrators, the resonance frequency of each vibrator cannot be adjusted independently. In this study, methods of reducing the coupling vibration were investigated by finite-element analysis. A method of adjusting the length of the short arm of each vibrator was proposed for reducing the vibration. When piezoelectric ceramics were bonded to the single-sided surface of the vibrator, the method was not sufficient. Thus, the ceramics with the same dimensions were bonded to double-sided surfaces. As a result, a marked reduction was obtained in this case. Also, the linearity of the sensor characteristics was significantly improved in a small acceleration range. Accordingly, it was clarified that considering the symmetry along the thickness direction of the vibrator is very important.

Egg-Independent Influenza Vaccines and Vaccine Candidates

PubMed Central

Manini, Ilaria; Pozzi, Teresa; Rossi, Stefania; Montomoli, Emanuele

2017-01-01

Vaccination remains the principal way to control seasonal infections and is the most effective method of reducing influenza-associated morbidity and mortality. Since the 1940s, the main method of producing influenza vaccines has been an egg-based production process. However, in the event of a pandemic, this method has a significant limitation, as the time lag from strain isolation to final dose formulation and validation is six months. Indeed, production in eggs is a relatively slow process and production yields are both unpredictable and highly variable from strain to strain. In particular, if the next influenza pandemic were to arise from an avian influenza virus, and thus reduce the egg-laying hen population, there would be a shortage of embryonated eggs available for vaccine manufacturing. Although the production of egg-derived vaccines will continue, new technological developments have generated a cell-culture-based influenza vaccine and other more recent platforms, such as synthetic influenza vaccines. PMID:28718786

Blood pressure control with selective vagal nerve stimulation and minimal side effects

NASA Astrophysics Data System (ADS)

Plachta, Dennis T. T.; Gierthmuehlen, Mortimer; Cota, Oscar; Espinosa, Nayeli; Boeser, Fabian; Herrera, Taliana C.; Stieglitz, Thomas; Zentner, Joseph

2014-06-01

Objective. Hypertension is the largest threat to patient health and a burden to health care systems. Despite various options, 30% of patients do not respond sufficiently to medical treatment. Mechanoreceptors in the aortic arch relay blood pressure (BP) levels through vagal nerve (VN) fibers to the brainstem and trigger the baroreflex, lowering the BP. Selective electrical stimulation of these nerve fibers reduced BP in rats. However, there is no technique described to localize and stimulate these fibers inside the VN without inadvertent stimulation of non-baroreceptive fibers causing side effects like bradycardia and bradypnea. Approach. We present a novel method for selective VN stimulation to reduce BP without the aforementioned side effects. Baroreceptor compound activity of rat VN (n = 5) was localized using a multichannel cuff electrode, true tripolar recording and a coherent averaging algorithm triggered by BP or electrocardiogram. Main results. Tripolar stimulation over electrodes near the barofibers reduced the BP without triggering significant bradycardia and bradypnea. The BP drop was adjusted to 60% of the initial value by varying the stimulation pulse width and duration, and lasted up to five times longer than the stimulation. Significance. The presented method is robust to impedance changes, independent of the electrode's relative position, does not compromise the nerve and can run on implantable, ultra-low power signal processors.

Solar variability: Implications for global change

NASA Technical Reports Server (NTRS)

Lean, Judith; Rind, David

1994-01-01

Solar variability is examined in search of implications for global change. The topics covered include the following: solar variation modification of global surface temperature; the significance of solar variability with respect to future climate change; and methods of reducing the uncertainty of the potential amplitude of solar variability on longer time scales.

Development of a qPCR direct detection method for Listeria monocytogenes in milk

USDA-ARS?s Scientific Manuscript database

There is a growing movement among consumers in the US and Europe towards minimally processed foods, including raw milk and dairy products. This trend significantly increases exposure to dairy-borne pathogens and indicates a need for rapid, sensitive screening tests for raw dairy products to reduce ...

Measurement Of Crossflow Vortex Structure

NASA Technical Reports Server (NTRS)

Maddalon, Dal V.; Agarwal, Navel K.

1994-01-01

Method developed for measuring wavelengths of crossflow vortices by using surface-mounted, microthin, multielement hot-film sensors. Provides direct and true value of wavelength of crossflow vortices at various spanwise locations without localized flow disturbances. Attainment of laminar airflow on aircraft wings has significant potential for reducing drag and increasing fuel efficiency.

Producing gapped-ferrite transformer cores

NASA Technical Reports Server (NTRS)

Mclyman, W. T.

1980-01-01

Improved manufacturing techniques make reproducible gaps and minimize cracking. Molded, unfired transformer cores are cut with thin saw and then fired. Hardened semicircular core sections are bonded together, placed in aluminum core box, and fluidized-coated. After winding is run over box, core is potted. Economical method significantly reduces number of rejects.

Critical Evaluation of Animal Alternative Tests for the Identification of Endocrine Active Substances, oral presentation

EPA Science Inventory

In the past 20 years, considerable progress in animal alternatives accompanied by advances in the toxicological sciences and new emphases on aquatic vertebrates has appeared. A significant amount of current research is targeted to evaluate alternative test methods that may reduce...

Critical Evaluation of Animal Alternative Tests for the Identification of Endocrine Active Substances

EPA Science Inventory

A significant amount of research is currently targeted to evaluate alternative test methods that may reduce, refine, or replace the use of animals, while ensuring human and environmental health and safety. It is important that the information gained from the alternative tests pr...

Treatment of Phobic Disorders Using Cognitive and Exposure Methods: A Self-Efficacy Analysis.

ERIC Educational Resources Information Center

Biran, Mia; Wilson, G. Terence

1981-01-01

Examined predictions derived from self-efficacy theory in comparing the effects of exposure and cognitive interventions with simple phobics. Guided exposure (GE) was significantly superior to cognitive restructuring (CR) in enhancing approach behavior, increasing level and strength of self-efficacy, reducing subjective fear, and decreasing…

Gene expression profiling of whole blood: Comparison of target preparation methods for accurate and reproducible microarray analysis

PubMed Central

Vartanian, Kristina; Slottke, Rachel; Johnstone, Timothy; Casale, Amanda; Planck, Stephen R; Choi, Dongseok; Smith, Justine R; Rosenbaum, James T; Harrington, Christina A

2009-01-01

Background Peripheral blood is an accessible and informative source of transcriptomal information for many human disease and pharmacogenomic studies. While there can be significant advantages to analyzing RNA isolated from whole blood, particularly in clinical studies, the preparation of samples for microarray analysis is complicated by the need to minimize artifacts associated with highly abundant globin RNA transcripts. The impact of globin RNA transcripts on expression profiling data can potentially be reduced by using RNA preparation and labeling methods that remove or block globin RNA during the microarray assay. We compared four different methods for preparing microarray hybridization targets from human whole blood collected in PAXGene tubes. Three of the methods utilized the Affymetrix one-cycle cDNA synthesis/in vitro transcription protocol but varied treatment of input RNA as follows: i. no treatment; ii. treatment with GLOBINclear; or iii. treatment with globin PNA oligos. In the fourth method cDNA targets were prepared with the Ovation amplification and labeling system. Results We find that microarray targets generated with labeling methods that reduce globin mRNA levels or minimize the impact of globin transcripts during hybridization detect more transcripts in the microarray assay compared with the standard Affymetrix method. Comparison of microarray results with quantitative PCR analysis of a panel of genes from the NF-kappa B pathway shows good correlation of transcript measurements produced with all four target preparation methods, although method-specific differences in overall correlation were observed. The impact of freezing blood collected in PAXGene tubes on data reproducibility was also examined. Expression profiles show little or no difference when RNA is extracted from either fresh or frozen blood samples. Conclusion RNA preparation and labeling methods designed to reduce the impact of globin mRNA transcripts can significantly improve the sensitivity of the DNA microarray expression profiling assay for whole blood samples. While blockage of globin transcripts during first strand cDNA synthesis with globin PNAs resulted in the best overall performance in this study, we conclude that selection of a protocol for expression profiling studies in blood should depend on several factors, including implementation requirements of the method and study design. RNA isolated from either freshly collected or frozen blood samples stored in PAXGene tubes can be used without altering gene expression profiles. PMID:19123946

Effects of heat stress on baroreflex function in humans

NASA Technical Reports Server (NTRS)

Crandall, Craig G.; Cui, Jian; Wilson, Thad E.

2003-01-01

INTRODUCTION: Heat stress significantly reduces orthostatic tolerance in humans. The mechanism(s) causing this response remain unknown. The purpose of this review article is to present data pertaining to the hypothesis that reduced orthostatic tolerance in heat stressed individuals is a result of heat stress induced alterations in baroflex function. METHODS: In both normothermic and heat stressed conditions baroreflex responsiveness was assessed via pharmacological and non-pharmacological methods. In addition, the effects of heat stress on post-synaptic vasoconstrictor responsiveness were assessed. RESULTS: Generally, whole body heating did not alter baroreflex sensitivity defined as the gain of the linear portion of the baroreflex curve around the operating point. However, whole body heating shifted the baroreflex curve to the prevailing (i.e. elevated) heart rate and muscle sympathetic nerve activity. Finally, the heat stress impaired vasoconstrictor responses to exogenous administration of adrenergic agonists. CONCLUSION: Current data do not support the hypothesis that reduced orthostatic tolerance associated with heat stress in humans is due to impaired baroreflex responsiveness. This phenomenon may be partially due to the effects of heat stress on reducing vasoconstrictor responsiveness.

Correlated natural transition orbital framework for low-scaling excitation energy calculations (CorNFLEx).

PubMed

Baudin, Pablo; Kristensen, Kasper

2017-06-07

We present a new framework for calculating coupled cluster (CC) excitation energies at a reduced computational cost. It relies on correlated natural transition orbitals (NTOs), denoted CIS(D')-NTOs, which are obtained by diagonalizing generalized hole and particle density matrices determined from configuration interaction singles (CIS) information and additional terms that represent correlation effects. A transition-specific reduced orbital space is determined based on the eigenvalues of the CIS(D')-NTOs, and a standard CC excitation energy calculation is then performed in that reduced orbital space. The new method is denoted CorNFLEx (Correlated Natural transition orbital Framework for Low-scaling Excitation energy calculations). We calculate second-order approximate CC singles and doubles (CC2) excitation energies for a test set of organic molecules and demonstrate that CorNFLEx yields excitation energies of CC2 quality at a significantly reduced computational cost, even for relatively small systems and delocalized electronic transitions. In order to illustrate the potential of the method for large molecules, we also apply CorNFLEx to calculate CC2 excitation energies for a series of solvated formamide clusters (up to 4836 basis functions).

Can changing the timing of outdoor air intake reduce indoor concentrations of traffic-related pollutants in schools?

PubMed

MacNeill, M; Dobbin, N; St-Jean, M; Wallace, L; Marro, L; Shin, T; You, H; Kulka, R; Allen, R W; Wheeler, A J

2016-10-01

Traffic emissions have been associated with a wide range of adverse health effects. Many schools are situated close to major roads, and as children spend much of their day in school, methods to reduce traffic-related air pollutant concentrations in the school environment are warranted. One promising method to reduce pollutant concentrations in schools is to alter the timing of the ventilation so that high ventilation time periods do not correspond to rush hour traffic. Health Canada, in collaboration with the Ottawa-Carleton District School Board, tested the effect of this action by collecting traffic-related air pollution data from four schools in Ottawa, Canada, during October and November 2013. A baseline and intervention period was assessed in each school. There were statistically significant (P < 0.05) reductions in concentrations of most of the pollutants measured at the two late-start (9 AM start) schools, after adjusting for outdoor concentrations and the absolute indoor-outdoor temperature difference. The intervention at the early-start (8 AM start) schools did not have significant reductions in pollutant concentrations. Based on these findings, changing the timing of the ventilation may be a cost-effective mechanism of reducing traffic-related pollutants in late-start schools located near major roads. © 2015 Her Majesty the Queen in Right of Canada. Indoor Air published by John Wiley & Sons Ltd. Reproduced with the permission of the Minister of Health Canada.

Exercise reduces depressive symptoms in adults with arthritis: Evidential value.

PubMed

Kelley, George A; Kelley, Kristi S

2016-07-12

To determine whether evidential value exists that exercise reduces depression in adults with arthritis and other rheumatic conditions. Utilizing data derived from a prior meta-analysis of 29 randomized controlled trials comprising 2449 participants (1470 exercise, 979 control) with fibromyalgia, osteoarthritis, rheumatoid arthritis or systemic lupus erythematosus, a new method, P -curve, was utilized to assess for evidentiary worth as well as dismiss the possibility of discriminating reporting of statistically significant results regarding exercise and depression in adults with arthritis and other rheumatic conditions. Using the method of Stouffer, Z -scores were calculated to examine selective-reporting bias. An alpha ( P ) value < 0.05 was deemed statistically significant. In addition, average power of the tests included in P -curve, adjusted for publication bias, was calculated. Fifteen of 29 studies (51.7%) with exercise and depression results were statistically significant ( P < 0.05) while none of the results were statistically significant with respect to exercise increasing depression in adults with arthritis and other rheumatic conditions. Right-skew to dismiss selective reporting was identified ( Z = -5.28, P < 0.0001). In addition, the included studies did not lack evidential value ( Z = 2.39, P = 0.99), nor did they lack evidential value and were P -hacked ( Z = 5.28, P > 0.99). The relative frequencies of P -values were 66.7% at 0.01, 6.7% each at 0.02 and 0.03, 13.3% at 0.04 and 6.7% at 0.05. The average power of the tests included in P -curve, corrected for publication bias, was 69%. Diagnostic plot results revealed that the observed power estimate was a better fit than the alternatives. Evidential value results provide additional support that exercise reduces depression in adults with arthritis and other rheumatic conditions.

The use of a modified technique to reduce radioactive air contamination in aerosol lung ventilation imaging.

PubMed

Avison, M; Hart, G

2001-06-01

The aim of this study was to reduce airborne contamination resulting from the use of aerosols in lung ventilation scintigraphy. Lung ventilation imaging is frequently performed with 99mTc-diethylenetriaminepentaacetate aerosol (DTPA), derived from a commercial nebuliser. Airborne contamination is a significant problem with this procedure; it results in exposure of staff to radiation and can reduce gamma camera performance when the ventilation is performed in the camera room. We examined the level of airborne contamination resulting from the standard technique with one of the most popular nebuliser kits and tested a modification which significantly reduced airborne contamination. Air contamination was measured while ventilating 122 patients. The modified technique reduced air contamination by a mean value of 64% (p = 0.028) compared with the standard control technique. Additionally, differences in contamination were examined when a mask or mouthpiece was used as well as differences between operators. A simplified method of monitoring air contamination is presented using a commonly available surface contamination monitor. The index so derived was proportional to air contamination (r = 0.88). The problems and regulations associated with airborne contamination are discussed.

Local Anaesthetic Infiltration and Indwelling Postoperative Wound Catheters for Patients with Hip Fracture Reduce Death Rates and Length of Stay

PubMed Central

Harrison, William D.; Lees, Deborah; A'Court, Jamie; Ankers, Thomas; Harper, Ian; Inman, Dominic; Reed, Mike R.

2015-01-01

Background. An analgesic enhanced recovery (ER) protocol for patients with a hip fracture was introduced. It was hypothesised that the ER would reduce pain, length of stay and improve clinical outcomes. The protocol used intraoperative infiltration of levobupivacaine followed by ongoing wound infusions. Methods. Consecutive patients admitted to two hospitals were eligible for the ER protocol. Numerical Reporting Scale pain scores (0–10) were recorded alongside opiate requirements. 434 patients in the ER group (316 full ER, 90 partial ER, and 28 no ER) were compared to a control group (CG) of 100 consecutive patients managed with traditional opiate analgesia. Results. Mean opiate requirement was 49.2 mg (CG) versus 32.5 mg (ER). Pain scores were significantly reduced in the full ER group, p < 0.0001. Direct discharge home and mean acute inpatient stay were significantly reduced (p = 0.0031 and p < 0.0001, resp.). 30-day mortality was 15% (CG) versus 5.5% (ER), p = 0.0024. Conclusions. This analgesic ER protocol for patients with a hip fracture was safe and effective and was associated with reduced inpatient stay and mortality. PMID:26649330

Working Overtime in Community Mental Health: Associations with Clinician Burnout and Perceived Quality of Care

PubMed Central

Luther, Lauren; Gearhart, Timothy; Fukui, Sadaaki; Morse, Gary; Rollins, Angela L.; Salyers, Michelle P.

2017-01-01

Objective Funding cuts have increased job demands and threatened clinicians’ ability to provide high-quality, person-centered care. One response to increased job demands is for clinicians to work more than their official scheduled work hours (i.e., overtime). We sought to examine the frequency of working overtime and its relationships with job characteristics, work-related outcomes, and quality of care in community health clinicians. Methods One hundred and eighty-two clinicians completed demographic and job characteristics questions and measures of burnout, job satisfaction, turnover intention, work-life conflict, and perceived quality of care. Clinicians also reported the importance of reducing stress and their confidence in reducing their stress. Clinicians who reported working overtime were compared to clinicians that did not on demographic and job characteristics and work-related outcomes. Results Ninety-four clinicians (52%) reported working overtime in a typical week. Controlling for exempt status and group differences in time spent supervising others, those working overtime reported significantly increased burnout and work-life conflict and significantly lower job satisfaction and quality of care than those not working overtime. Clinicians working overtime also reported significantly greater importance in reducing stress but less confidence in their ability to reduce stress than those not working overtime. There were no significant group differences for turnover intention. Conclusions and Implications for Practice Working overtime is associated with negative consequences for clinician-related work outcomes and perceived quality of care. Policies and interventions aimed at reducing overtime and work-related stress and burnout may be warranted in order to improve quality of care. PMID:27786520

Flavonoid metabolites reduce tumor necrosis factor‐α secretion to a greater extent than their precursor compounds in human THP‐1 monocytes

PubMed Central

di Gesso, Jessica L.; Kerr, Jason S.; Zhang, Qingzhi; Raheem, Saki; Yalamanchili, Sai Krishna; O'Hagan, David; Kay, Colin D.; O'Connell, Maria A.

2015-01-01

1 Scope Flavonoids are generally studied in vitro, in isolation, and as unmetabolized precursor structures. However, in the habitual diet, multiple flavonoids are consumed together and found present in the circulation as complex mixtures of metabolites. Using a unique study design, we investigated the potential for singular or additive anti‐inflammatory effects of flavonoid metabolites relative to their precursor structures. 2 Methods and results Six flavonoids, 14 flavonoid metabolites, and 29 combinations of flavonoids and their metabolites (0.1–10 μM) were screened for their ability to reduce LPS‐induced tumor necrosis factor‐α (TNF‐α) secretion in THP‐1 monocytes. One micromolar peonidin‐3‐glucoside, cyanidin‐3‐glucoside, and the metabolites isovanillic acid (IVA), IVA‐glucuronide, vanillic acid‐glucuronide, protocatechuic acid‐3‐sulfate, and benzoic acid‐sulfate significantly reduced TNF‐α secretion when in isolation, while there was no effect on TNF‐α mRNA expression. Four combinations of metabolites that included 4‐hydroxybenzoic acid (4HBA) and/or protocatechuic acid also significantly reduced TNF‐α secretion to a greater extent than the precursors or metabolites alone. The effects on LPS‐induced IL‐1β and IL‐10 secretion and mRNA expression were also examined. 4HBA significantly reduced IL‐1β secretion but none of the flavonoids or metabolites significantly modified IL‐10 secretion. 3 Conclusion This study provides novel evidence suggesting flavonoid bioactivity results from cumulative or additive effects of circulating metabolites. PMID:25801720

Slightly acidic electrolyzed water for reducing airborne microorganisms in a layer breeding house.

PubMed

Hao, Xiaoxia; Cao, Wei; Li, Baoming; Zhang, Qiang; Wang, Chaoyuan; Ge, Liangpeng

2014-04-01

Reducing airborne microorganisms may potentially improve the environment in layer breeding houses. The effectiveness of slightly acidic electrolyzed water (SAEW; pH 5.29-6.30) in reducing airborne microorganisms was investigated in a commercial layer house in northern China. The building had a tunnel-ventilation system, with an evaporative cooling. The experimental area was divided into five zones along the length of the house, with zone 1 nearest to an evaporative cooling pad and zone 5 nearest to the fans. The air temperature, relative humidity, dust concentration, and microbial population were measured at the sampling points in the five zones during the study period. The SAEW was sprayed by workers in the whole house. A six-stage air microbial sampler was used to measure airborne microbial population. Results showed that the population of airborne bacteria and fungi were sharply reduced by 0.71 x 10(5) and 2.82 x 10(3) colony-forming units (CFU) m(-3) after 30 min exposure to SAEW, respectively. Compared with the benzalkonium chloride (BC) solution and povidone-iodine (PVP-I) solution treatments, the population reductions of airborne fungi treated by SAEW were significantly (P < 0.05) more, even though the three disinfectants can decrease both the airborne bacteria and fungi significantly (P < 0.05) 30 min after spraying. There are no effective methods for reducing airborne microbial levels in tunnel-ventilated layer breeding houses; additionally, there is limited information available on airborne microorganism distribution. This research investigated the spatial distribution of microbial population, and the effectiveness of spraying slightly acidic electrolyzed water in reducing microbial levels. The research revealed that slightly acidic electrolyzed water spray was a potential method for reducing microbial presence in layer houses. The knowledge gained in this research about the microbial population variations in the building may assist producers in managing the bird housing environment and engineers in designing poultry houses.

Self-consistent field for fragmented quantum mechanical model of large molecular systems.

PubMed

Jin, Yingdi; Su, Neil Qiang; Xu, Xin; Hu, Hao

2016-01-30

Fragment-based linear scaling quantum chemistry methods are a promising tool for the accurate simulation of chemical and biomolecular systems. Because of the coupled inter-fragment electrostatic interactions, a dual-layer iterative scheme is often employed to compute the fragment electronic structure and the total energy. In the dual-layer scheme, the self-consistent field (SCF) of the electronic structure of a fragment must be solved first, then followed by the updating of the inter-fragment electrostatic interactions. The two steps are sequentially carried out and repeated; as such a significant total number of fragment SCF iterations is required to converge the total energy and becomes the computational bottleneck in many fragment quantum chemistry methods. To reduce the number of fragment SCF iterations and speed up the convergence of the total energy, we develop here a new SCF scheme in which the inter-fragment interactions can be updated concurrently without converging the fragment electronic structure. By constructing the global, block-wise Fock matrix and density matrix, we prove that the commutation between the two global matrices guarantees the commutation of the corresponding matrices in each fragment. Therefore, many highly efficient numerical techniques such as the direct inversion of the iterative subspace method can be employed to converge simultaneously the electronic structure of all fragments, reducing significantly the computational cost. Numerical examples for water clusters of different sizes suggest that the method shall be very useful in improving the scalability of fragment quantum chemistry methods. © 2015 Wiley Periodicals, Inc.

Point of care hemoglobin testing in plateletpheresis donors: Noninvasive versus invasive methods.

PubMed

Mallhi, R S; Pawar, Amit; Kushwaha, Neerja; Kumar, Sudeep; Dimri, Ujjwal

2016-10-01

Predonation hemoglobin (Hb) for plateletpheresis donors is estimated by presently available invasive methods. Venous samples of only those donors whose Hb is more than 12.5 g/dl are screened for complete blood count and transfusion transmissible infections. There is a pressing need to substitute this invasive Hb test with noninvasive one to reduce donor discomfort and avoid further pricking the donor. We therefore went ahead with the aim of comparing a noninvasive Hb estimation method NBM 200 with the invasive method - Hemocue, taking SYSMEX KX-21 as a gold standard. 500 voluntary consenting plateletpheresis donors qualifying the laid down criteria for platelet donation were included in the study. Hb readings obtained by the NBM 200 and Hemocue were compared to those obtained from the fully automated hematology analyzer SYSMEX KX-21. Coefficients of correlation were found to be statistically significant at <0.0001 level of confidence. Results of Friedman's test on the three methods also showed significant difference in means. Bland-Altman plots and mountain plots also confirm the same. NBM 200 was found to be more sensitive, specific, and precise than Hemocue in detecting ineligible donors. NBM 200 was found to be more sensitive, specific, and precise as compared to Hemocue for predonation screening of Hb in plateletpheresis donors and the prime benefit it offers is that it is 'noninvasive' thereby assisting in stemming the platelet donor pool. The onus lies on the blood transfusion services to make use of appropriately validated gadgets that reduce the donor discomfort.

Biomechanics of unilateral and bilateral sacroiliac joint stabilization: laboratory investigation.

PubMed

Lindsey, Derek P; Parrish, Robin; Gundanna, Mukund; Leasure, Jeremi; Yerby, Scott A; Kondrashov, Dimitriy

2018-03-01

OBJECTIVE Bilateral symptoms have been reported in 8%-35% of patients with sacroiliac (SI) joint dysfunction. Stabilization of a single SI joint may significantly alter the stresses on the contralateral SI joint. If the contralateral SI joint stresses are significantly increased, degeneration may occur; alternatively, if the stresses are significantly reduced, bilateral stabilization may be unnecessary for patients with bilateral symptoms. The biomechanical effects of 1) unilateral stabilization on the contralateral SI joint and 2) bilateral stabilization on both SI joints are currently unknown. The objectives of this study were to characterize bilateral SI joint range of motion (ROM) and evaluate and compare the biomechanical effects of unilateral and bilateral implant placement for SI joint fusion. METHODS A lumbopelvic model (L5-pelvis) was used to test the ROM of both SI joints in 8 cadavers. A single-leg stance setup was used to load the lumbar spine and measure the ROM of each SI joint in flexion-extension, lateral bending, and axial rotation. Both joints were tested 1) while intact, 2) after unilateral stabilization, and 3) after bilateral stabilization. Stabilization consisted of lateral transiliac placement of 3 triangular titanium plasma-sprayed (TPS) implants. RESULTS Intact testing showed that during single-leg stance the contralateral SI joint had less ROM in flexion-extension (27%), lateral bending (32%), and axial rotation (69%) than the loaded joint. Unilateral stabilization resulted in significant reduction of flexion-extension ROM (46%) on the treated side; no significant ROM changes were observed for the nontreated side. Bilateral stabilization resulted in significant reduction of flexion-extension ROM of the primary (45%) and secondary (75%) SI joints. CONCLUSIONS This study demonstrated that during single-leg loading the ROMs for the stance (loaded) and swing (unloaded) SI joints are significantly different. Unilateral stabilization for SI joint dysfunction significantly reduces the ROM of the treated side, but does not significantly reduce the ROM of the nontreated contralateral SI joint. Bilateral stabilization is necessary to significantly reduce the ROM for both SI joints.

A study on the dependence of exposure dose reduction and image evaluation on the distance from the dental periapical X-ray machine

NASA Astrophysics Data System (ADS)

Joo, Kyu-Ji; Shin, Jae-Woo; Dong, Kyung-Rae; Lim, Chang-Seon; Chung, Woon-Kwan; Kim, Young-Jae

2013-11-01

Reducing the exposure dose from a periapical X-ray machine is an important aim in dental radiography. Although the radiation exposure dose is generally low, any radiation exposure is harmful to the human body. Therefore, this study developed a method that reduces the exposure dose significantly compared to that encountered in a normal procedure, but still produces an image with a similar resolution. The correlation between the image resolution and the exposure dose of the proposed method was examined with increasing distance between the dosimeter and the X-ray tube. The results were compared with those obtained from the existing radiography method. When periapical radiography was performed once according to the recommendations of the International Commission on Radiological Protection (ICRP), the measured skin surface dose was low at 7 mGy or below. In contrast, the skin surface dose measured using the proposed method was only 1.57 mGy, showing a five-fold reduction. These results suggest that further decreases in dose might be achieved using the proposed method.

The impacts of speed cameras on road accidents: an application of propensity score matching methods.

PubMed

Li, Haojie; Graham, Daniel J; Majumdar, Arnab

2013-11-01

This paper aims to evaluate the impacts of speed limit enforcement cameras on reducing road accidents in the UK by accounting for both confounding factors and the selection of proper reference groups. The propensity score matching (PSM) method is employed to do this. A naïve before and after approach and the empirical Bayes (EB) method are compared with the PSM method. A total of 771 sites and 4787 sites for the treatment and the potential reference groups respectively are observed for a period of 9 years in England. Both the PSM and the EB methods show similar results that there are significant reductions in the number of accidents of all severities at speed camera sites. It is suggested that the propensity score can be used as the criteria for selecting the reference group in before-after control studies. Speed cameras were found to be most effective in reducing accidents up to 200 meters from camera sites and no evidence of accident migration was found. Copyright © 2013 Elsevier Ltd. All rights reserved.

How to detect and reduce movement artifacts in near-infrared imaging using moving standard deviation and spline interpolation.

PubMed

Scholkmann, F; Spichtig, S; Muehlemann, T; Wolf, M

2010-05-01

Near-infrared imaging (NIRI) is a neuroimaging technique which enables us to non-invasively measure hemodynamic changes in the human brain. Since the technique is very sensitive, the movement of a subject can cause movement artifacts (MAs), which affect the signal quality and results to a high degree. No general method is yet available to reduce these MAs effectively. The aim was to develop a new MA reduction method. A method based on moving standard deviation and spline interpolation was developed. It enables the semi-automatic detection and reduction of MAs in the data. It was validated using simulated and real NIRI signals. The results show that a significant reduction of MAs and an increase in signal quality are achieved. The effectiveness and usability of the method is demonstrated by the improved detection of evoked hemodynamic responses. The present method can not only be used in the postprocessing of NIRI signals but also for other kinds of data containing artifacts, for example ECG or EEG signals.

Estimation of the Thermal Process in the Honeycomb Panel by a Monte Carlo Method

NASA Astrophysics Data System (ADS)

Gusev, S. A.; Nikolaev, V. N.

2018-01-01

A new Monte Carlo method for estimating the thermal state of the heat insulation containing honeycomb panels is proposed in the paper. The heat transfer in the honeycomb panel is described by a boundary value problem for a parabolic equation with discontinuous diffusion coefficient and boundary conditions of the third kind. To obtain an approximate solution, it is proposed to use the smoothing of the diffusion coefficient. After that, the obtained problem is solved on the basis of the probability representation. The probability representation is the expectation of the functional of the diffusion process corresponding to the boundary value problem. The process of solving the problem is reduced to numerical statistical modelling of a large number of trajectories of the diffusion process corresponding to the parabolic problem. It was used earlier the Euler method for this object, but that requires a large computational effort. In this paper the method is modified by using combination of the Euler and the random walk on moving spheres methods. The new approach allows us to significantly reduce the computation costs.

Effect of Guar Gum with Sorbitol Coating on the Properties and Oil Absorption of French Fries.

PubMed

Jia, Bo; Fan, Daming; Li, Jinwei; Duan, Zhenhua; Fan, Liuping

2017-12-13

This paper investigated the effects of guar gum with sorbitol coating on the oil absorption of French fries by combined dye oil methods, confocal laser scanning microscopy (CLSM) and scanning electron microscopy (SEM). The results showed that pretreatment of blanching with calcium ions and coating with guar gum and sorbitol could significantly reduce the structural oil (STO) and penetrated surface oil (PSO) of French fries and have no negative effects on its texture and also effectively control the final moisture content ( p < 0.05). Compared with control or samples coated with guar gum (blanching with or without calcium ions), the total oil (TO) of French fries with guar gum and sorbitol reduced by 50.8%, 33.1% and 30.6%, respectively. CLSM photographs confirmed that STO significantly reduced after coating with guar gum and sorbitol, followed by PSO. In the process of frying, the coatings of guar gum or guar gum with sorbitol could effectively prevent oil from infiltrating the potato tissue, which can be seen in the SEM photographs. The barrier properties of French fries were enhanced by coating guar gum, and sorbitol was added to avoid pores and cracks. Blanching with calcium ion can significantly reduce the final moisture content of coating French fries.

Reduced age-related degeneration of the hippocampal subiculum in long-term meditators.

PubMed

Kurth, Florian; Cherbuin, Nicolas; Luders, Eileen

2015-06-30

Normal aging is known to result in a reduction of gray matter within the hippocampal complex, particularly in the subiculum. The present study was designed to address the question whether the practice of meditation can amend this age-related subicular atrophy. For this purpose, we established the correlations between subicular volume and chronological age within 50 long-term meditators and 50 control subjects. High-resolution magnetic resonance imaging (MRI) scans were automatically processed combining cytoarchitectonically defined probabilistic maps with advanced tissue segmentation and registration methods. Overall, we observed steeper negative regression slopes in controls. The analysis further revealed a significant group-by-age interaction for the left subiculum with a significant negative correlation between age and subicular volume in controls, but no significant correlation in meditators. Altogether, these findings seem to suggest a reduced age-related atrophy of the left subiculum in meditators compared to healthy controls. Possible explanations might be a relative increase of subicular tissue over time through long-term training as meditation is a process that incorporates regular and ongoing mental efforts. Alternatively, because meditation is an established form of reducing stress, our observation might reflect an overall preservation of subicular tissue through a reduced neuronal vulnerability to negative effects of stress. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Effect of Guar Gum with Sorbitol Coating on the Properties and Oil Absorption of French Fries

PubMed Central

Jia, Bo; Fan, Daming; Li, Jinwei; Duan, Zhenhua; Fan, Liuping

2017-01-01

This paper investigated the effects of guar gum with sorbitol coating on the oil absorption of French fries by combined dye oil methods, confocal laser scanning microscopy (CLSM) and scanning electron microscopy (SEM). The results showed that pretreatment of blanching with calcium ions and coating with guar gum and sorbitol could significantly reduce the structural oil (STO) and penetrated surface oil (PSO) of French fries and have no negative effects on its texture and also effectively control the final moisture content (p < 0.05). Compared with control or samples coated with guar gum (blanching with or without calcium ions), the total oil (TO) of French fries with guar gum and sorbitol reduced by 50.8%, 33.1% and 30.6%, respectively. CLSM photographs confirmed that STO significantly reduced after coating with guar gum and sorbitol, followed by PSO. In the process of frying, the coatings of guar gum or guar gum with sorbitol could effectively prevent oil from infiltrating the potato tissue, which can be seen in the SEM photographs. The barrier properties of French fries were enhanced by coating guar gum, and sorbitol was added to avoid pores and cracks. Blanching with calcium ion can significantly reduce the final moisture content of coating French fries. PMID:29236044

Comparison of Acute Health Effects From Exposures to Diesel and Biodiesel Fuel Emissions

PubMed Central

Mehus, Aaron A.; Reed, Rustin J.; Lee, Vivien S. T.; Littau, Sally R.; Hu, Chengcheng; Lutz, Eric A.

2015-01-01

Objective: To investigate the comparative acute health effects associated with exposures to diesel and 75% biodiesel/25% diesel (B75) blend fuel emissions. Methods: We analyzed multiple health endpoints in 48 healthy adults before and after exposures to diesel and B75 emissions in an underground mine setting—lung function, lung and systemic inflammation, novel biomarkers of exposure, and oxidative stress were assessed. Results: B75 reduced respirable diesel particulate matter by 20%. Lung function declined significantly more after exposure to diesel emissions. Lung inflammatory cells along with sputum and plasma inflammatory mediators increased significantly to similar levels with both exposures. Urinary 8-hydroxydeoxyguanosine, a marker of oxidative stress, was not significantly changed after either exposure. Conclusions: Use of B75 lowered respirable diesel particulate matter exposure and some associated acute health effects, although lung and systemic inflammation were not reduced compared with diesel use. PMID:26147538

Results from the Xylitol for Adult Caries Trial (X-ACT)

PubMed Central

Bader, James D.; Vollmer, William M.; Shugars, Daniel A.; Gilbert, Gregg H.; Amaechi, Bennett T.; Brown, John P.; Laws, Reesa L.; Funkhouser, Kimberly A.; Makhija, Sonia K.; Ritter, André V.; Leo, Michael C.

2013-01-01

Background Although caries is prevalent in adults, few preventive therapies have been tested in adult populations. This randomized clinical trial evaluated the effectiveness of xylitol lozenges in preventing caries in elevated caries-risk adults. Methods X-ACT was a three-site placebo-controlled randomized trial. Participants (n=691) ages 21–80 consumed five 1.0 g xylitol or placebo lozenges daily for 33 months. Clinical examinations occurred at baseline, 12, 24 and 33 months. Results Xylitol lozenges reduced the caries increment 11%. This reduction, which represented less than one-third of a surface per year, was not statistically significant. There was no indication of a dose-response effect. Conclusions Daily use of xylitol lozenges did not result in a statistically or clinically significant reduction in 33-month caries increment among elevated caries-risk adults. Clinical Implications These results suggest that xylitol used as a supplement in adults does not significantly reduce their caries experience. PMID:23283923

Effect of Immobilized Antithrombin III on the Thromboresistance of Polycarbonate Urethane.

PubMed

Lukas, Karin; Stadtherr, Karin; Gessner, Andre; Wehner, Daniel; Schmid, Thomas; Wendel, Hans Peter; Schmid, Christof; Lehle, Karla

2017-03-24

The surface of foils and vascular grafts made from a thermoplastic polycarbonate urethanes (PCU) (Chronoflex AR) were chemically modified using gas plasma treatment, binding of hydrogels-(1) polyethylene glycol bisdiamine and carboxymethyl dextran (PEG-DEX) and (2) polyethyleneimine (PEI)-and immobilization of human antithrombin III (AT). Their biological impact was tested in vitro under static and dynamic conditions. Static test methods showed a significantly reduced adhesion of endothelial cells, platelets, and bacteria, compared to untreated PCU. Modified PCU grafts were circulated in a Chandler-Loop model for 90 min at 37 °C with human blood. Before and after circulation, parameters of the hemostatic system (coagulation, platelets, complement, and leukocyte activation) were analyzed. PEI-AT significantly inhibited the activation of both coagulation and platelets and prevented the activation of leukocytes and complement. In conclusion, both modifications significantly reduce coagulation activation, but only PEI-AT creates anti-bacterial and anti-thrombogenic functionality.

Reducing false-positive incidental findings with ensemble genotyping and logistic regression based variant filtering methods.

PubMed

Hwang, Kyu-Baek; Lee, In-Hee; Park, Jin-Ho; Hambuch, Tina; Choe, Yongjoon; Kim, MinHyeok; Lee, Kyungjoon; Song, Taemin; Neu, Matthew B; Gupta, Neha; Kohane, Isaac S; Green, Robert C; Kong, Sek Won

2014-08-01

As whole genome sequencing (WGS) uncovers variants associated with rare and common diseases, an immediate challenge is to minimize false-positive findings due to sequencing and variant calling errors. False positives can be reduced by combining results from orthogonal sequencing methods, but costly. Here, we present variant filtering approaches using logistic regression (LR) and ensemble genotyping to minimize false positives without sacrificing sensitivity. We evaluated the methods using paired WGS datasets of an extended family prepared using two sequencing platforms and a validated set of variants in NA12878. Using LR or ensemble genotyping based filtering, false-negative rates were significantly reduced by 1.1- to 17.8-fold at the same levels of false discovery rates (5.4% for heterozygous and 4.5% for homozygous single nucleotide variants (SNVs); 30.0% for heterozygous and 18.7% for homozygous insertions; 25.2% for heterozygous and 16.6% for homozygous deletions) compared to the filtering based on genotype quality scores. Moreover, ensemble genotyping excluded > 98% (105,080 of 107,167) of false positives while retaining > 95% (897 of 937) of true positives in de novo mutation (DNM) discovery in NA12878, and performed better than a consensus method using two sequencing platforms. Our proposed methods were effective in prioritizing phenotype-associated variants, and an ensemble genotyping would be essential to minimize false-positive DNM candidates. © 2014 WILEY PERIODICALS, INC.

Reducing false positive incidental findings with ensemble genotyping and logistic regression-based variant filtering methods

PubMed Central

Hwang, Kyu-Baek; Lee, In-Hee; Park, Jin-Ho; Hambuch, Tina; Choi, Yongjoon; Kim, MinHyeok; Lee, Kyungjoon; Song, Taemin; Neu, Matthew B.; Gupta, Neha; Kohane, Isaac S.; Green, Robert C.; Kong, Sek Won

2014-01-01

As whole genome sequencing (WGS) uncovers variants associated with rare and common diseases, an immediate challenge is to minimize false positive findings due to sequencing and variant calling errors. False positives can be reduced by combining results from orthogonal sequencing methods, but costly. Here we present variant filtering approaches using logistic regression (LR) and ensemble genotyping to minimize false positives without sacrificing sensitivity. We evaluated the methods using paired WGS datasets of an extended family prepared using two sequencing platforms and a validated set of variants in NA12878. Using LR or ensemble genotyping based filtering, false negative rates were significantly reduced by 1.1- to 17.8-fold at the same levels of false discovery rates (5.4% for heterozygous and 4.5% for homozygous SNVs; 30.0% for heterozygous and 18.7% for homozygous insertions; 25.2% for heterozygous and 16.6% for homozygous deletions) compared to the filtering based on genotype quality scores. Moreover, ensemble genotyping excluded > 98% (105,080 of 107,167) of false positives while retaining > 95% (897 of 937) of true positives in de novo mutation (DNM) discovery, and performed better than a consensus method using two sequencing platforms. Our proposed methods were effective in prioritizing phenotype-associated variants, and ensemble genotyping would be essential to minimize false positive DNM candidates. PMID:24829188

Arithmetic functions in torus and tree networks

DOEpatents

Bhanot, Gyan; Blumrich, Matthias A.; Chen, Dong; Gara, Alan G.; Giampapa, Mark E.; Heidelberger, Philip; Steinmacher-Burow, Burkhard D.; Vranas, Pavlos M.

2007-12-25

Methods and systems for performing arithmetic functions. In accordance with a first aspect of the invention, methods and apparatus are provided, working in conjunction of software algorithms and hardware implementation of class network routing, to achieve a very significant reduction in the time required for global arithmetic operation on the torus. Therefore, it leads to greater scalability of applications running on large parallel machines. The invention involves three steps in improving the efficiency and accuracy of global operations: (1) Ensuring, when necessary, that all the nodes do the global operation on the data in the same order and so obtain a unique answer, independent of roundoff error; (2) Using the topology of the torus to minimize the number of hops and the bidirectional capabilities of the network to reduce the number of time steps in the data transfer operation to an absolute minimum; and (3) Using class function routing to reduce latency in the data transfer. With the method of this invention, every single element is injected into the network only once and it will be stored and forwarded without any further software overhead. In accordance with a second aspect of the invention, methods and systems are provided to efficiently implement global arithmetic operations on a network that supports the global combining operations. The latency of doing such global operations are greatly reduced by using these methods.

Impact of glucuronide interferences on therapeutic drug monitoring of posaconazole by tandem mass spectrometry.

PubMed

Krüger, Ralf; Vogeser, Michael; Burghardt, Stephan; Vogelsberger, Rita; Lackner, Karl J

2010-12-01

Posaconazole is a novel antifungal drug for oral application intended especially for therapy of invasive mycoses. Due to variable gastrointestinal absorption, adverse side effects, and suspected drug-drug interactions, therapeutic drug monitoring (TDM) of posaconazole is recommended. A fast ultra performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) method for quantification of posaconazole with a run-time <3 min was developed and compared to a LC-MS/MS method and HPLC method with fluorescence detection. During evaluation of UPLC-MS/MS, two earlier eluting peaks were observed in the MRM trace of posaconazole. This was only seen in patient samples, but not in spiked calibrator samples. Comparison with LC-MS/MS disclosed a significant bias with higher concentrations measured by LC-MS/MS, while UPLC-MS/MS showed excellent agreement with the commercially available HPLC method. In the LC-MS/MS procedure, comparably wide and left side shifted peaks were noticed. This could be ascribed to in-source fragmentation of conjugate metabolites during electrospray ionisation. Precursor and product ion scans confirmed the assumption that the additional compounds are posaconazole glucuronides. Reducing the cone voltage led to disappearance of the glucuronide peaks. Slight modification of the LC-MS/MS method enabled separation of the main interference, leading to significantly reduced deviation. These results highlight the necessity to reliably eliminate interference from labile drug metabolites for correct TDM results, either by sufficient separation or selective MS conditions. The presented UPLC-MS/MS method provides a reliable and fast assay for TDM of posaconazole.

Rapid micro-scale proteolysis of proteins for MALDI-MS peptide mapping using immobilized trypsin

NASA Astrophysics Data System (ADS)

Gobom, Johan; Nordhoff, Eckhard; Ekman, Rolf; Roepstorff, Peter

1997-12-01

In this study we present a rapid method for tryptic digestion of proteins using micro-columns with enzyme immobilized on perfusion chromatography media. The performance of the method is exemplified with acyl-CoA-binding protein and reduced carbamidomethylated bovine serum albumin. The method proved to be significantly faster and yielded a better sequence coverage and an improved signal-to-noise ratio for the MALDI-MS peptide maps, compared to in-solution- and on-target digestion. Only a single sample transfer step is required, and therefore sample loss due to adsorption to surfaces is reduced, which is a critical issue when handling low picomole to femtomole amounts of proteins. An example is shown with on-column proteolytic digestion and subsequent elution of the digest into a reversed-phase micro-column. This is useful if the sample contains large amounts of salt or is too diluted for MALDI-MS analysis. Furthermore, by step-wise elution from the reversedphase column, a complex digest can be fractionated, which reduces signal suppression and facilitates data interpretation in the subsequent MS-analysis. The method also proved useful for consecutive digestions with enzymes of different cleavage specificity. This is exemplified with on-column tryptic digestion, followed by reversed-phase step-wise elution, and subsequent on-target V8 protease digestion.

The bias, accuracy and precision of faecal egg count reduction test results in cattle using McMaster, Cornell-Wisconsin and FLOTAC egg counting methods.

PubMed

Levecke, B; Rinaldi, L; Charlier, J; Maurelli, M P; Bosco, A; Vercruysse, J; Cringoli, G

2012-08-13

The faecal egg count reduction test (FECRT) is the recommended method to monitor anthelmintic drug efficacy in cattle. There is a large variation in faecal egg count (FEC) methods applied to determine FECRT. However, it remains unclear whether FEC methods with an equal analytic sensitivity, but with different methodologies, result in equal FECRT results. We therefore, compared the bias, accuracy and precision of FECRT results for Cornell-Wisconsin (analytic sensitivity = 1 egg per gram faeces (EPG)), FLOTAC (analytic sensitivity = 1 EPG) and McMaster method (analytic sensitivity = 10 EPG) across four levels of egg excretion (1-49 EPG; 50-149 EPG; 150-299 EPG; 300-600 EPG). Finally, we assessed the sensitivity of the FEC methods to detect a truly reduced efficacy. To this end, two different criteria were used to define reduced efficacy based on FECR, including those described in the WAAVP guidelines (FECRT <95% and lower limit of 95%CI <90%) (Coles et al., 1992) and those proposed by El-Abdellati et al. (2010) (upper limit of 95%CI <95%). There was no significant difference in bias and accuracy of FECRT results across the three methods. FLOTAC provided the most precise FECRT results. Cornell-Wisconsin and McMaster gave similar imprecise results. FECRT were significantly underestimated when baseline FEC were low and drugs were more efficacious. For all FEC methods, precision and accuracy of the FECRT improved as egg excretion increased, this effect was greatest for McMaster and least for Cornell-Wisconsin. The sensitivity of the three methods to detect a truly reduced efficacy was high (>90%). Yet, the sensitivity of McMaster and Cornell-Wisconsin may drop when drugs only show sub-optimal efficacy. Overall, the study indicates that the precision of FECRT is affected by the methodology of FEC, and that the level of egg excretion should be considered in the final interpretation of the FECRT. However, more comprehensive studies are required to provide more insights into the complex interplay of factors inherent to study design (sample size and FEC method) and host-parasite interactions (level of egg excretion and aggregation across the host population). Copyright © 2012 Elsevier B.V. All rights reserved.

Faecal indicator bacteria enumeration in beach sand: A comparison study of extraction methods in medium to coarse sands

USGS Publications Warehouse

Boehm, A.B.; Griffith, J.; McGee, C.; Edge, T.A.; Solo-Gabriele, H. M.; Whitman, R.; Cao, Y.; Getrich, M.; Jay, J.A.; Ferguson, D.; Goodwin, K.D.; Lee, C.M.; Madison, M.; Weisberg, S.B.

2009-01-01

Aims: The absence of standardized methods for quantifying faecal indicator bacteria (FIB) in sand hinders comparison of results across studies. The purpose of the study was to compare methods for extraction of faecal bacteria from sands and recommend a standardized extraction technique. Methods and Results: Twenty-two methods of extracting enterococci and Escherichia coli from sand were evaluated, including multiple permutations of hand shaking, mechanical shaking, blending, sonication, number of rinses, settling time, eluant-to-sand ratio, eluant composition, prefiltration and type of decantation. Tests were performed on sands from California, Florida and Lake Michigan. Most extraction parameters did not significantly affect bacterial enumeration. anova revealed significant effects of eluant composition and blending; with both sodium metaphosphate buffer and blending producing reduced counts. Conclusions: The simplest extraction method that produced the highest FIB recoveries consisted of 2 min of hand shaking in phosphate-buffered saline or deionized water, a 30-s settling time, one-rinse step and a 10 : 1 eluant volume to sand weight ratio. This result was consistent across the sand compositions tested in this study but could vary for other sand types. Significance and Impact of the Study: Method standardization will improve the understanding of how sands affect surface water quality. ?? 2009 The Society for Applied Microbiology.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Niu, T; Dong, X; Petrongolo, M

Purpose: Dual energy CT (DECT) imaging plays an important role in advanced imaging applications due to its material decomposition capability. Direct decomposition via matrix inversion suffers from significant degradation of image signal-to-noise ratios, which reduces clinical value. Existing de-noising algorithms achieve suboptimal performance since they suppress image noise either before or after the decomposition and do not fully explore the noise statistical properties of the decomposition process. We propose an iterative image-domain decomposition method for noise suppression in DECT, using the full variance-covariance matrix of the decomposed images. Methods: The proposed algorithm is formulated in the form of least-square estimationmore » with smoothness regularization. It includes the inverse of the estimated variance-covariance matrix of the decomposed images as the penalty weight in the least-square term. Performance is evaluated using an evaluation phantom (Catphan 600) and an anthropomorphic head phantom. Results are compared to those generated using direct matrix inversion with no noise suppression, a de-noising method applied on the decomposed images, and an existing algorithm with similar formulation but with an edge-preserving regularization term. Results: On the Catphan phantom, our method retains the same spatial resolution as the CT images before decomposition while reducing the noise standard deviation of decomposed images by over 98%. The other methods either degrade spatial resolution or achieve less low-contrast detectability. Also, our method yields lower electron density measurement error than direct matrix inversion and reduces error variation by over 97%. On the head phantom, it reduces the noise standard deviation of decomposed images by over 97% without blurring the sinus structures. Conclusion: We propose an iterative image-domain decomposition method for DECT. The method combines noise suppression and material decomposition into an iterative process and achieves both goals simultaneously. The proposed algorithm shows superior performance on noise suppression with high image spatial resolution and low-contrast detectability. This work is supported by a Varian MRA grant.« less

Measurement of temperature induced in bone during drilling in minimally invasive foot surgery.

PubMed

Omar, Noor Azzizah; McKinley, John C

2018-02-19

There has been growing interest in minimally invasive foot surgery due to the benefits it delivers in post-operative outcomes in comparison to conventional open methods of surgery. One of the major factors determining the protocol in minimally invasive surgery is to prevent iatrogenic thermal osteonecrosis. The aim of the study is to look at various drilling parameters in a minimally invasive surgery setting that would reduce the risk of iatrogenic thermal osteonecrosis. Sixteen fresh-frozen tarsal bones and two metatarsal bones were retrieved from three individuals and drilled using various settings. The parameters considered were drilling speed, drill diameter, and inter-individual cortical variability. Temperature measurements of heat generated at the drilling site were collected using two methods; thermocouple probe and infrared thermography. The data obtained were quantitatively analysed. There was a significant difference in the temperatures generated with different drilling speeds (p<0.05). However, there was no significant difference in temperatures recorded between the bones of different individuals and in bones drilled using different drill diameters. Thermocouple showed significantly more sensitive tool in measuring temperature compared to infrared thermography. Drilling at an optimal speed significantly reduced the risk of iatrogenic thermal osteonecrosis by maintaining temperature below the threshold level. Although different drilling diameters did not produce significant differences in temperature generation, there is a need for further study on the mechanical impact of using different drill diameters. Copyright © 2018 Elsevier Ltd. All rights reserved.

Treatment of Subacromial Impingement Syndrome: Platelet-Rich Plasma or Exercise Therapy? A Randomized Controlled Trial

PubMed Central

Nejati, Parisa; Ghahremaninia, Armita; Naderi, Farrokh; Gharibzadeh, Safoora; Mazaherinezhad, Ali

2017-01-01

Background: Subacromial impingement syndrome (SAIS) is the most common disorder of the shoulder. The evidence for the effectiveness of treatment options is inconclusive and limited. Therefore, there is a need for more evidence in this regard, particularly for long-term outcomes. Hypothesis: Platelet-rich plasma (PRP) would be an effective method in treating subacromial impingement. Study Design: Randomized controlled trial; Level of evidence, 1. Methods: This was a single-blinded randomized clinical trial with 1-, 3-, and 6-month follow-up. Sixty-two patients were randomly placed into 2 groups, receiving either PRP or exercise therapy. The outcome parameters were pain, shoulder range of motion (ROM), muscle force, functionality, and magnetic resonance imaging findings. Results: Both treatment options significantly reduced pain and increased shoulder ROM compared with baseline measurements. Both treatments also significantly improved functionality. However, the treatment choices were not significantly effective in improving muscle force. Trend analysis revealed that in the first and third months, exercise therapy was superior to PRP in pain, shoulder flexion and abduction, and functionality. However, in the sixth month, only shoulder abduction and total Western Ontario Rotator Cuff score were significantly different between the 2 groups. Conclusion: Both PRP injection and exercise therapy were effective in reducing pain and disability in patients with SAIS, with exercise therapy proving more effective. PMID:28567426

Estimating snow depth of alpine snowpack via airborne multifrequency passive microwave radiance observations: Colorado, USA

NASA Astrophysics Data System (ADS)

Kim, R. S.; Durand, M. T.; Li, D.; Baldo, E.; Margulis, S. A.; Dumont, M.; Morin, S.

2017-12-01

This paper presents a newly-proposed snow depth retrieval approach for mountainous deep snow using airborne multifrequency passive microwave (PM) radiance observation. In contrast to previous snow depth estimations using satellite PM radiance assimilation, the newly-proposed method utilized single flight observation and deployed the snow hydrologic models. This method is promising since the satellite-based retrieval methods have difficulties to estimate snow depth due to their coarse resolution and computational effort. Indeed, this approach consists of particle filter using combinations of multiple PM frequencies and multi-layer snow physical model (i.e., Crocus) to resolve melt-refreeze crusts. The method was performed over NASA Cold Land Processes Experiment (CLPX) area in Colorado during 2002 and 2003. Results showed that there was a significant improvement over the prior snow depth estimates and the capability to reduce the prior snow depth biases. When applying our snow depth retrieval algorithm using a combination of four PM frequencies (10.7,18.7, 37.0 and 89.0 GHz), the RMSE values were reduced by 48 % at the snow depth transects sites where forest density was less than 5% despite deep snow conditions. This method displayed a sensitivity to different combinations of frequencies, model stratigraphy (i.e. different number of layering scheme for snow physical model) and estimation methods (particle filter and Kalman filter). The prior RMSE values at the forest-covered areas were reduced by 37 - 42 % even in the presence of forest cover.

Tribo-functionalizing Si and SU8 materials by surface modification for application in MEMS/NEMS actuator-based devices

NASA Astrophysics Data System (ADS)

Singh, R. A.; Satyanarayana, N.; Kustandi, T. S.; Sinha, S. K.

2011-01-01

Micro/nano-electro-mechanical-systems (MEMS/NEMS) are miniaturized devices built at micro/nanoscales. At these scales, the surface/interfacial forces are extremely strong and they adversely affect the smooth operation and the useful operating lifetimes of such devices. When these forces manifest in severe forms, they lead to material removal and thereby reduce the wear durability of the devices. In this paper, we present a simple, yet robust, two-step surface modification method to significantly enhance the tribological performance of MEMS/NEMS materials. The two-step method involves oxygen plasma treatment of polymeric films and the application of a nanolubricant, namely perfluoropolyether. We apply the two-step method to the two most important MEMS/NEMS structural materials, namely silicon and SU8 polymer. On applying surface modification to these materials, their initial coefficient of friction reduces by ~4-7 times and the steady-state coefficient of friction reduces by ~2.5-3.5 times. Simultaneously, the wear durability of both the materials increases by >1000 times. The two-step method is time effective as each of the steps takes the time duration of approximately 1 min. It is also cost effective as the oxygen plasma treatment is a part of the MEMS/NEMS fabrication process. The two-step method can be readily and easily integrated into MEMS/NEMS fabrication processes. It is anticipated that this method will work for any kind of structural material from which MEMS/NEMS are or can be made.

Autogenic-Feedback Training Exercise (AFTE) Method and System

NASA Technical Reports Server (NTRS)

Cowings, Patricia S. (Inventor)

1997-01-01

The Autogenic-Feedback Training Exercise (AFTE) method of the present invention is a combined application of physiologic and perceptual training techniques. such as autogenic therapy and biofeedback. This combined therapy approach produces a methodology that is appreciably more effective than either of the individual techniques used separately. The AFTE method enables sufficient magnitude of control necessary to significantly reduce the behavioral and physiologic reactions to severe environmental stressors. It produces learned effects that are persistent over time and are resistant to extinction and it can be administered in a short period of time. The AFTE method may be used efficiently in several applications, among which are the following: to improve pilot and crew performance during emergency flying conditions; to train people to prevent the occurrence of nausea and vomiting associated with motion and sea sickness, or morning sickness in early pregnancy; as a training method for preventing or counteracting air-sickness symptoms in high-performance military aircraft; for use as a method for cardiovascular training, as well as for multiple other autonomic responses, which may contribute to the alleviation of Space Motion Sickness (SMS) in astronauts and cosmonauts; training people suffering from migraine or tension headaches to control peripheral blood flow and reduce forehead and/or trapezius muscle tension; training elderly people suffering from fecal incontinence to control their sphincter muscles; training cancer patients to reduce the nauseagenic effects of chemotherapy; and training patients with Chronic Intestinal Pseudo-obstruction (CIP).

High strength air-dried aerogels

DOEpatents

Coronado, Paul R.; Satcher, Jr., Joe H.

2012-11-06

A method for the preparation of high strength air-dried organic aerogels. The method involves the sol-gel polymerization of organic gel precursors, such as resorcinol with formaldehyde (RF) in aqueous solvents with R/C ratios greater than about 1000 and R/F ratios less than about 1:2.1. Using a procedure analogous to the preparation of resorcinol-formaldehyde (RF) aerogels, this approach generates wet gels that can be air dried at ambient temperatures and pressures. The method significantly reduces the time and/or energy required to produce a dried aerogel compared to conventional methods using either supercritical solvent extraction. The air dried gel exhibits typically less than 5% shrinkage.

Regional interpretation of water-quality monitoring data

USGS Publications Warehouse

Smith, Richard A.; Schwarz, Gregory E.; Alexander, Richard B.

1997-01-01

We describe a method for using spatially referenced regressions of contaminant transport on watershed attributes (SPARROW) in regional water-quality assessment. The method is designed to reduce the problems of data interpretation caused by sparse sampling, network bias, and basin heterogeneity. The regression equation relates measured transport rates in streams to spatially referenced descriptors of pollution sources and land-surface and stream-channel characteristics. Regression models of total phosphorus (TP) and total nitrogen (TN) transport are constructed for a region defined as the nontidal conterminous United States. Observed TN and TP transport rates are derived from water-quality records for 414 stations in the National Stream Quality Accounting Network. Nutrient sources identified in the equations include point sources, applied fertilizer, livestock waste, nonagricultural land, and atmospheric deposition (TN only). Surface characteristics found to be significant predictors of land-water delivery include soil permeability, stream density, and temperature (TN only). Estimated instream decay coefficients for the two contaminants decrease monotonically with increasing stream size. TP transport is found to be significantly reduced by reservoir retention. Spatial referencing of basin attributes in relation to the stream channel network greatly increases their statistical significance and model accuracy. The method is used to estimate the proportion of watersheds in the conterminous United States (i.e., hydrologic cataloging units) with outflow TP concentrations less than the criterion of 0.1 mg/L, and to classify cataloging units according to local TN yield (kg/km2/yr).

[Method of correcting sensitivity nonuniformity using gaussian distribution on 3.0 Tesla abdominal MRI].

PubMed

Hayashi, Norio; Miyati, Tosiaki; Takanaga, Masako; Ohno, Naoki; Hamaguchi, Takashi; Kozaka, Kazuto; Sanada, Shigeru; Yamamoto, Tomoyuki; Matsui, Osamu

2011-01-01

In the direction where the phased array coil used in parallel magnetic resonance imaging (MRI) is perpendicular to the arrangement, sensitivity falls significantly. Moreover, in a 3.0 tesla (3T) abdominal MRI, the quality of the image is reduced by changes in the relaxation time, reinforcement of the magnetic susceptibility effect, etc. In a 3T MRI, which has a high resonant frequency, the signal of the depths (central part) is reduced in the trunk part. SCIC, which is sensitivity correction processing, has inadequate correction processing, such as that edges are emphasized and the central part is corrected. Therefore, we used 3T with a Gaussian distribution. The uneven compensation processing for sensitivity of an abdomen MR image was considered. The correction processing consisted of the following methods. 1) The center of gravity of the domain of the human body in an abdomen MR image was calculated. 2) The correction coefficient map was created from the center of gravity using the Gaussian distribution. 3) The sensitivity correction image was created from the correction coefficient map and the original picture image. Using the Gaussian correction to process the image, the uniformity calculated using the NEMA method was improved significantly compared to the original image of a phantom. In a visual evaluation by radiologists, the uniformity was improved significantly using the Gaussian correction processing. Because of the homogeneous improvement of the abdomen image taken using 3T MRI, the Gaussian correction processing is considered to be a very useful technique.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turner, A.; Davis, A.; University of Wisconsin-Madison, Madison, WI 53706

CCFE perform Monte-Carlo transport simulations on large and complex tokamak models such as ITER. Such simulations are challenging since streaming and deep penetration effects are equally important. In order to make such simulations tractable, both variance reduction (VR) techniques and parallel computing are used. It has been found that the application of VR techniques in such models significantly reduces the efficiency of parallel computation due to 'long histories'. VR in MCNP can be accomplished using energy-dependent weight windows. The weight window represents an 'average behaviour' of particles, and large deviations in the arriving weight of a particle give rise tomore » extreme amounts of splitting being performed and a long history. When running on parallel clusters, a long history can have a detrimental effect on the parallel efficiency - if one process is computing the long history, the other CPUs complete their batch of histories and wait idle. Furthermore some long histories have been found to be effectively intractable. To combat this effect, CCFE has developed an adaptation of MCNP which dynamically adjusts the WW where a large weight deviation is encountered. The method effectively 'de-optimises' the WW, reducing the VR performance but this is offset by a significant increase in parallel efficiency. Testing with a simple geometry has shown the method does not bias the result. This 'long history method' has enabled CCFE to significantly improve the performance of MCNP calculations for ITER on parallel clusters, and will be beneficial for any geometry combining streaming and deep penetration effects. (authors)« less

Quantitative Assessment of Blood Pressure Measurement Accuracy and Variability from Visual Auscultation Method by Observers without Receiving Medical Training

PubMed Central

Feng, Yong; Chen, Aiqing

2017-01-01

This study aimed to quantify blood pressure (BP) measurement accuracy and variability with different techniques. Thirty video clips of BP recordings from the BHS training database were converted to Korotkoff sound waveforms. Ten observers without receiving medical training were asked to determine BPs using (a) traditional manual auscultatory method and (b) visual auscultation method by visualizing the Korotkoff sound waveform, which was repeated three times on different days. The measurement error was calculated against the reference answers, and the measurement variability was calculated from the SD of the three repeats. Statistical analysis showed that, in comparison with the auscultatory method, visual method significantly reduced overall variability from 2.2 to 1.1 mmHg for SBP and from 1.9 to 0.9 mmHg for DBP (both p < 0.001). It also showed that BP measurement errors were significant for both techniques (all p < 0.01, except DBP from the traditional method). Although significant, the overall mean errors were small (−1.5 and −1.2 mmHg for SBP and −0.7 and 2.6 mmHg for DBP, resp., from the traditional auscultatory and visual auscultation methods). In conclusion, the visual auscultation method had the ability to achieve an acceptable degree of BP measurement accuracy, with smaller variability in comparison with the traditional auscultatory method. PMID:29423405

Comportement d'une source karstique soumise à une sécheresse prolongée : la source Bittit (Maroc)

NASA Astrophysics Data System (ADS)

Amraoui, Fouad; Razack, Moumtaz; Bouchaou, Lhoussaine

2004-09-01

The behaviour of a karstic spring (Bittit spring, Middle Atlas, Morocco) subjected to a prolonged drought (>20 yr), is analysed using spring hydrographs analysis methods and correlation and spectral methods. Two series of discharges, corresponding to a normal rainfall period and a drought period, are analysed. The results show that the karstic system is inertial, with very significant storage. However, in spite of the great regulating capacity of the storage, the long drought period significantly reduced the spring discharges, due to less diversified inputs, and to the karstic system storage depletion. To cite this article: F. Amraoui et al., C. R. Geoscience 336 (2004).

Employment of sawtooth-shaped-function excitation signal and oversampling for improving resistance measurement accuracy

NASA Astrophysics Data System (ADS)

Lin, Ling; Li, Shujuan; Yan, Wenjuan; Li, Gang

2016-10-01

In order to achieve higher measurement accuracy of routine resistance without increasing the complexity and cost of the system circuit of existing methods, this paper presents a novel method that exploits a shaped-function excitation signal and oversampling technology. The excitation signal source for resistance measurement is modulated by the sawtooth-shaped-function signal, and oversampling technology is employed to increase the resolution and the accuracy of the measurement system. Compared with the traditional method of using constant amplitude excitation signal, this method can effectively enhance the measuring accuracy by almost one order of magnitude and reduce the root mean square error by 3.75 times under the same measurement conditions. The results of experiments show that the novel method can attain the aim of significantly improve the measurement accuracy of resistance on the premise of not increasing the system cost and complexity of the circuit, which is significantly valuable for applying in electronic instruments.

[Analysis of the stability and adaptability of near infrared spectra qualitative analysis model].

PubMed

Cao, Wu; Li, Wei-jun; Wang, Ping; Zhang, Li-ping

2014-06-01

The stability and adaptability of model of near infrared spectra qualitative analysis were studied. Method of separate modeling can significantly improve the stability and adaptability of model; but its ability of improving adaptability of model is limited. Method of joint modeling can not only improve the adaptability of the model, but also the stability of model, at the same time, compared to separate modeling, the method can shorten the modeling time, reduce the modeling workload; extend the term of validity of model, and improve the modeling efficiency. The experiment of model adaptability shows that, the correct recognition rate of separate modeling method is relatively low, which can not meet the requirements of application, and joint modeling method can reach the correct recognition rate of 90%, and significantly enhances the recognition effect. The experiment of model stability shows that, the identification results of model by joint modeling are better than the model by separate modeling, and has good application value.

Adaptive simplification of complex multiscale systems.

PubMed

Chiavazzo, Eliodoro; Karlin, Ilya

2011-03-01

A fully adaptive methodology is developed for reducing the complexity of large dissipative systems. This represents a significant step toward extracting essential physical knowledge from complex systems, by addressing the challenging problem of a minimal number of variables needed to exactly capture the system dynamics. Accurate reduced description is achieved, by construction of a hierarchy of slow invariant manifolds, with an embarrassingly simple implementation in any dimension. The method is validated with the autoignition of the hydrogen-air mixture where a reduction to a cascade of slow invariant manifolds is observed.

Inverse kinematics of a dual linear actuator pitch/roll heliostat

NASA Astrophysics Data System (ADS)

Freeman, Joshua; Shankar, Balakrishnan; Sundaram, Ganesh

2017-06-01

This work presents a simple, computationally efficient inverse kinematics solution for a pitch/roll heliostat using two linear actuators. The heliostat design and kinematics have been developed, modeled and tested using computer simulation software. A physical heliostat prototype was fabricated to validate the theoretical computations and data. Pitch/roll heliostats have numerous advantages including reduced cost potential and reduced space requirements, with a primary disadvantage being the significantly more complicated kinematics, which are solved here. Novel methods are applied to simplify the inverse kinematics problem which could be applied to other similar problems.

Poloxamer-188 reduces muscular edema after tourniquet-induced ischemia-reperfusion injury in rats.

PubMed

Walters, Thomas J; Mase, Vincent J; Roe, Janet L; Dubick, Michael A; Christy, Robert J

2011-05-01

Skeletal muscle injury can result in significant edema, which can in turn lead to the development of acute extremity compartment syndrome (CS). Poloxamer-188 (P-188), a multiblock copolymer surfactant, has been shown to decrease edema by sealing damaged membranes in a number of tissues after a variety of injury modalities. The objective is to determine whether the administration of P-188 significantly reduces skeletal muscle edema associated with ischemia/reperfusion injury (I-R). Male Sprague-Dawley rats underwent 180 minutes of tourniquet-induced ischemia. Five minutes before tourniquet release, rats received either a bolus of (1) P-188 (150 mg/kg; P-188 group) or (2) vehicle (Vehicle group) via a jugular catheter (n=10 per group). After 240 minutes reperfusion, both groups received a second bolus of either P-188 (P-188) or vehicle (Vehicle) via a tail vein catheter. Sixteen hours later, rats were killed; muscle weights were determined, infarct size (2,3,5-triphenyltetrazolium chloride method), and blinded histologic analysis (hematoxylin and eosin) were performed on the gastrocnemius and tibialis anterior muscles, as well as indices of antioxidant status. P-188 resulted in significantly less edema (wet weight) and reduced an index of lipid peroxidation compared with Vehicle (p<0.05). Wet:dry weight ratios were less in the P-188 group (indicating less edema). Muscle viability as indicated by 2,3,5-triphenyltetrazolium chloride staining or routine histology did not reveal statistically significant differences between groups. P-188 significantly reduced ischemia-reperfusion-related muscle edema and lipid peroxidation but did not impact muscle viability. Excess edema can lead to acute extremity CS, which is associated with significant morbidity and mortality. P-188 may provide a potential adjunctive treatment for the reduction of CS.

Ginger extract and aerobic training reduces lipid profile in high-fat fed diet rats.

PubMed

Khosravani, M; Azarbayjani, M A; Abolmaesoomi, M; Yusof, A; Zainal Abidin, N; Rahimi, E; Feizolahi, F; Akbari, M; Seyedjalali, S; Dehghan, F

2016-04-01

Obesity, hyperglycemia and dyslipidemia, are major risk factors. However, natural therapies, dietary components, and physical activity may effect on these concerns. The aim of this study was to examine the effect of aerobic exercise and consumption of liquid ginger extract on lipid profile of Male rats with a high-fat fed diet. 32 rats were randomly divided into 4 groups: 1) aerobic exercise, 2) Ginger extract, 3) combined aerobic exercise and Ginger extract, and 4) the control. Subjects of the first three groups received ginger extract via gavage feeding of 250 mg/kg. The exercise program was 3 sessions per week on 3 different days over 4 weeks. Total cholesterol (TC), Triglyceride (TG), HDL and LDL were measured 24-h before the first session and 24-h after the final training session. The concentration of TG in the control group was significantly higher than other groups. In addition, the mean concentration of TG in the aerobic exercise group was significantly lower than Ginger extract group but there was no significant difference as compared to combined aerobic exercise and ginger extract group. The combination of aerobic exercise and ginger consumption significantly reduced the TG level compared to ginger group. TC and LDL concentrations were significantly decreased in all groups compare to control. The combination of aerobic exercise and ginger extract feeding caused a significant increase in HDL levels. The finding of this study suggests that the combination of aerobic exercise and liquid ginger extract consumption might be an effective method of reducing lipid profiles, which will reduce the risk of cardiovascular diseases caused by high-fat diets.

Comparison of two methods for recovering migrating Ascaris suum larvae from the liver and lungs of pigs.

PubMed

Slotved, H C; Roepstorff, A; Barnes, E H; Eriksen, L; Nansen, P

1996-08-01

Nine groups of 5 pigs were inoculated with Ascaris suum eggs on day 0. Groups 1, 2, and 3 were inoculated with 100 eggs, groups 4, 5, and 6 with 1,000 eggs, and groups 7, 8, and 9 with 10,000 eggs. On day 3, groups 1, 4, and 7 were slaughtered, on day 7 groups 2, 5, and 8, and on day 10 groups 3, 6, and 9. The liver (days 3 and 7) and lungs (days 3, 7, and 10) were removed and 2, 25% samples of both organs were collected. Larvae were recovered from 1 sample by the Baermann method and from the other by an agar-gel method. Overall there were no significant differences in the liver larval recovery between the 2 methods. The use of the agar-gel method resulted in a very clean suspension of larvae and thereby reduced the sample counting time by a factor of 5-10 compared to the Baermann method. With both methods larval recovery from the lungs resulted in a clean larval suspension that was easy to count, and there were overall no significant differences between the 2 methods, although there was a tendency toward the Baermann method recovering more larvae from the lungs than the agar-gel method. The tissue sample dry weight did not significantly influence larval recovery by the agar-gel method, and the time interval from slaughtering to start of incubation on day 3 (interval 51-92 min), day 7 (interval 37-114 min), and day 10 (interval 50-129 min) had no significant effect on recovery by either method.

A Comparison of Hand Wrist Bone Analysis with Two Different Cervical Vertebral Analysis in Measuring Skeletal Maturation

PubMed Central

Pichai, Saravanan; Rajesh, M; Reddy, Naveen; Adusumilli, Gopinath; Reddy, Jayaprakash; Joshi, Bhavana

2014-01-01

Background: Skeletal maturation is an integral part of individual pattern of growth and development and is a continuous process. Peak growth velocity in standing height is the most valid representation of the rate of overall skeletal growth. Ossification changes of hand wrist and cervical vertebrae are the reliable indicators of growth status of individual. The objective of this study was to compare skeletal maturation as measured by hand wrist bone analysis and cervical vertebral analysis. Materials and Methods: Hand wrist radiographs and lateral cephalograms of 72 subjects aged between 7 and 16 years both male and female from the patients visiting Department of Orthodontics and Dentofacial Orthopedics, R.V. Dental College and Hospital. The 9 stages were reduced to 5 stages to compare with cervical vertebral maturation stage by Baccetti et al. The Bjork, Grave and Brown stages were reduced to six intervals to compare with cervical vertebral maturational index (CVMI) staging by Hassel and Farman. These measurements were then compared with the hand wrist bone analysis, and the results were statistically analyzed using the Mann–Whitney test. Results: There was no significant difference between the hand wrist analysis and the two different cervical vertebral analyses for assessing skeletal maturation. There was no significant difference between the two cervical vertebral analyses, but the CVMI method, which is visual method is less time consuming. Conclusion: Vertebral analysis on a lateral cephalogram is as valid as the hand wrist bone analysis with the advantage of reducing the radiation exposure of growing subjects. PMID:25395791

Progress Toward Affordable High Fidelity Combustion Simulations Using Filtered Density Functions for Hypersonic Flows in Complex Geometries

NASA Technical Reports Server (NTRS)

Drozda, Tomasz G.; Quinlan, Jesse R.; Pisciuneri, Patrick H.; Yilmaz, S. Levent

2012-01-01

Significant progress has been made in the development of subgrid scale (SGS) closures based on a filtered density function (FDF) for large eddy simulations (LES) of turbulent reacting flows. The FDF is the counterpart of the probability density function (PDF) method, which has proven effective in Reynolds averaged simulations (RAS). However, while systematic progress is being made advancing the FDF models for relatively simple flows and lab-scale flames, the application of these methods in complex geometries and high speed, wall-bounded flows with shocks remains a challenge. The key difficulties are the significant computational cost associated with solving the FDF transport equation and numerically stiff finite rate chemistry. For LES/FDF methods to make a more significant impact in practical applications a pragmatic approach must be taken that significantly reduces the computational cost while maintaining high modeling fidelity. An example of one such ongoing effort is at the NASA Langley Research Center, where the first generation FDF models, namely the scalar filtered mass density function (SFMDF) are being implemented into VULCAN, a production-quality RAS and LES solver widely used for design of high speed propulsion flowpaths. This effort leverages internal and external collaborations to reduce the overall computational cost of high fidelity simulations in VULCAN by: implementing high order methods that allow reduction in the total number of computational cells without loss in accuracy; implementing first generation of high fidelity scalar PDF/FDF models applicable to high-speed compressible flows; coupling RAS/PDF and LES/FDF into a hybrid framework to efficiently and accurately model the effects of combustion in the vicinity of the walls; developing efficient Lagrangian particle tracking algorithms to support robust solutions of the FDF equations for high speed flows; and utilizing finite rate chemistry parametrization, such as flamelet models, to reduce the number of transported reactive species and remove numerical stiffness. This paper briefly introduces the SFMDF model (highlighting key benefits and challenges), and discusses particle tracking for flows with shocks, the hybrid coupled RAS/PDF and LES/FDF model, flamelet generated manifolds (FGM) model, and the Irregularly Portioned Lagrangian Monte Carlo Finite Difference (IPLMCFD) methodology for scalable simulation of high-speed reacting compressible flows.

Advanced Hydrogen Liquefaction Process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schwartz, Joseph; Kromer, Brian; Neu, Ben

2011-09-28

The project identified and quantified ways to reduce the cost of hydrogen liquefaction, and reduce the cost of hydrogen distribution. The goal was to reduce the power consumption by 20% and then to reduce the capital cost. Optimizing the process, improving process equipment, and improving ortho-para conversion significantly reduced the power consumption of liquefaction, but by less than 20%. Because the efficiency improvement was less than the target, the program was stopped before the capital cost was addressed. These efficiency improvements could provide a benefit to the public to improve the design of future hydrogen liquefiers. The project increased themore » understanding of hydrogen liquefaction by modeling different processes and thoroughly examining ortho-para separation and conversion. The process modeling provided a benefit to the public because the project incorporated para hydrogen into the process modeling software, so liquefaction processes can be modeled more accurately than using only normal hydrogen. Adding catalyst to the first heat exchanger, a simple method to reduce liquefaction power, was identified, analyzed, and quantified. The demonstrated performance of ortho-para separation is sufficient for at least one identified process concept to show reduced power cost when compared to hydrogen liquefaction processes using conventional ortho-para conversion. The impact of improved ortho-para conversion can be significant because ortho para conversion uses about 20-25% of the total liquefaction power, but performance improvement is necessary to realize a substantial benefit. Most of the energy used in liquefaction is for gas compression. Improvements in hydrogen compression will have a significant impact on overall liquefier efficiency. Improvements to turbines, heat exchangers, and other process equipment will have less impact.« less

Effects of electroacupuncture on corticotropin-releasing hormone in rats with chronic visceral hypersensitivity

PubMed Central

Liu, Hui-Rong; Fang, Xiao-Yi; Wu, Huan-Gan; Wu, Lu-Yi; Li, Jing; Weng, Zhi-Jun; Guo, Xin-Xin; Li, Yu-Guang

2015-01-01

AIM: To investigate the effect of electroacupuncture on corticotropin-releasing hormone (CRH) in the colon, spinal cord, and hypothalamus of rats with chronic visceral hypersensitivity. METHODS: A rat model of chronic visceral hypersensitivity was generated according to the internationally accepted method of colorectal balloon dilatation. In the 7th week after the procedure, rats were randomly divided into a model group (MG), electroacupuncture group (EA), and sham electroacupuncture group (S-EA). After treatment, the abdominal withdrawal reflex (AWR) score was used to assess the behavioral response of visceral hyperalgesia. Immunohistochemistry (EnVision method), ELISA, and fluorescence quantitative PCR methods were applied to detect the expression of CRH protein and mRNA in the colon, spinal cord, and hypothalamus. RESULTS: The sensitivity of the rats to the colorectal distension stimulus applied at different strengths (20-80 mmHg) increased with increasing stimulus strength, resulting in increasing AWR scores in each group. Compared with NG, the AWR score of MG was significantly increased (P < 0.01). After conducting EA, the AWR scores of the rats were decreased compared with MG rats. The relative expression of CRH mRNA in the colon, spinal cord, and hypothalamus of MG rats was significantly increased compared with NG rats (P < 0.01). CRH mRNA in the colon and spinal cord of EA and S-EA rats was decreased to varying degrees (P > 0.05) compared with normal rats (NG). However, the decrease in EA compared with MG rats was statistically significant (P < 0.01). The average optical density of CRH expression in the colon of the MG rats was significantly enhanced compared with NG (P < 0.05), while the average optical density of CRH expression in the EA and S-EA rats was significantly decreased compared with MG rats (P < 0.01, P < 0.05, respectively). Compared with MG rats, the CRH concentration in the spinal cord of EA rats was significantly reduced (P < 0.01), but there was no significant change in S-EA rats (P > 0.05). CONCLUSION: Electroacupuncture at the Shangjuxu acupoint was able to significantly reduce the visceral hypersensitivity in rats, and regulated the expression of CRH protein and mRNA in the colon, spinal cord and hypothalamus at different levels, playing a therapeutic role in this model of irritable bowel syndrome. PMID:26109804

Human Activity Recognition from Smart-Phone Sensor Data using a Multi-Class Ensemble Learning in Home Monitoring.

PubMed

Ghose, Soumya; Mitra, Jhimli; Karunanithi, Mohan; Dowling, Jason

2015-01-01

Home monitoring of chronically ill or elderly patient can reduce frequent hospitalisations and hence provide improved quality of care at a reduced cost to the community, therefore reducing the burden on the healthcare system. Activity recognition of such patients is of high importance in such a design. In this work, a system for automatic human physical activity recognition from smart-phone inertial sensors data is proposed. An ensemble of decision trees framework is adopted to train and predict the multi-class human activity system. A comparison of our proposed method with a multi-class traditional support vector machine shows significant improvement in activity recognition accuracies.

Blockade of epithelial membrane protein 2 (EMP2) abrogates infection of Chlamydia muridarum murine genital infection model

PubMed Central

Shimazaki, Kaori; Chan, Ann M.; Moniz, Raymond J.; Wadehra, Madhuri; Nagy, Agnes; Coulam, C. Paige; Mareninov, Sergey; Lepin, Eric M.; Wu, Anna M.; Kelly, Kathleen A.; Braun, Jonathan; Gordon, Lynn K.

2012-01-01

New methods are needed to eradicate or prevent Chlamydia trachomatis infections. Blockade of epithelial membrane protein 2 (EMP2) by genetic silencing or neutralizing polyclonal antibody reduced chlamydial infectivity in vitro. This study tests the prediction that recombinant anti-EMP2 diabody could reduce early chlamydial infection of the genital tract in vivo. In a murine infection model, pretreatment with anti-EMP2 diabody, as compared to control diabody, significantly reduced bacterial load, tissue production of inflammatory cytokines, recruitment of polymorphonuclear leukocytes, and local tissue inflammation. These findings support EMP2 as a potential preventative and therapeutic target for genital chlamydial infection. PMID:19159428

Quality improvement project to reduce infiltration and extravasation events in a pediatric hospital.

PubMed

Tofani, Barbara F; Rineair, Sylvia A; Gosdin, Craig H; Pilcher, Patricia M; McGee, Susan; Varadarajan, Kartik R; Schoettker, Pamela J

2012-12-01

A safety event response team at Cincinnati Children's Hospital Medical Center developed and tested improvement strategies to reduce peripheral intravenous (PIV) infiltration and extravasation injuries. Improvement activities included development of the touch-look-compare method for hourly PIV site assessment, staff education and mandatory demonstration of PIV site assessment, and performance monitoring and sharing of compliance results. We observed a significant reduction in the injury rate immediately following implementation of the interventions that corresponded with monitoring compliance in performing hourly assessments on patients with a PIV, but this was not sustained. The team is currently examining other strategies to reduce PIV injuries. Copyright © 2012 Elsevier Inc. All rights reserved.

Pulse transmission transmitter including a higher order time derivate filter

DOEpatents

Dress, Jr., William B.; Smith, Stephen F.

2003-09-23

Systems and methods for pulse-transmission low-power communication modes are disclosed. A pulse transmission transmitter includes: a clock; a pseudorandom polynomial generator coupled to the clock, the pseudorandom polynomial generator having a polynomial load input; an exclusive-OR gate coupled to the pseudorandom polynomial generator, the exclusive-OR gate having a serial data input; a programmable delay circuit coupled to both the clock and the exclusive-OR gate; a pulse generator coupled to the programmable delay circuit; and a higher order time derivative filter coupled to the pulse generator. The systems and methods significantly reduce lower-frequency emissions from pulse transmission spread-spectrum communication modes, which reduces potentially harmful interference to existing radio frequency services and users and also simultaneously permit transmission of multiple data bits by utilizing specific pulse shapes.

A new in vitro bioassay system for discovery and quantitative evaluation of mosquito repellents

USDA-ARS?s Scientific Manuscript database

Mosquitoes are vectors of many pathogens that cause human diseases. Although prevention and control of immature stages is the best method to control mosquitoes, repellents play a significant role in reducing the risk of these diseases by preventing mosquito bites. The In vitro K & D bioassay system ...

Computerized Adaptive Personality Testing: A Review and Illustration With the MMPI-2 Computerized Adaptive Version.

ERIC Educational Resources Information Center

Forbey, Johnathan D.; Ben-Porath, Yossef S.

2007-01-01

Computerized adaptive testing in personality assessment can improve efficiency by significantly reducing the number of items administered to answer an assessment question. Two approaches have been explored for adaptive testing in computerized personality assessment: item response theory and the countdown method. In this article, the authors…

Alternatives to in vivo Tests to Detect Endocrine Disrupting Chemicals (EDCs) in Fish and Amphibians

EPA Science Inventory

A significant amount of current research in risk assessment of chemicals is targeted to evaluate alternative test methods that may reduce, replace or refine the use of animals, while ensuring human and environmental health and safety. In 2009, the US EPA began implementation of t...